Combustion of sodium in the open atmosphere

International Nuclear Information System (INIS)

Morewith, H.A.; Johnson, R.P.; Nelson, C.T.; Otter, J.M.

1979-01-01

A series of sodium fire tests has been conducted in ambient air at a meteorological test site. This test series was designed to simulate hypothetical accidents which might occur in the heat transport system of an LMFBR. Measurements of concentration, agglomeration, fallout, and chemical species of the sodium combustion products were made as a function of downwind distance. In each of the first two tests, ∼23 kg of 540 deg. C sodium was sprayed as a fan of 250-μm sodium drops across the wind, from heights of 5 or 6 m. Each release took a few minutes. A dense sodium combustion product aerosol was formed, and quickly agglomerated to large (100 to 660 μm) diameter particles. More than 50% of the aerosol mass fell out within several hundred meters of the release point. Two additional tests were performed by releasing sodium through 9.5-mm diameter jets at a height of 30 m. In each test, the sodium jet was aimed horizontally across the wind, and followed a downward parabolic trajectory, releasing burning sodium drops along its track. Again, close-in fallout due to large agglomerates was observed. A substantial amount of unburned sodium fell 30 m to the ground, where it burned. In a third type of test, sodium was burned for 60 min as pool in a 1.5m 2 burn pan at 9 m/s wind velocity. Approximately 30% of the combustion products became airborne. Large agglomerates fell out as they moved downwind, depositing 1 kg/m 2 at 1 m downwind from the edge of the pan. Chemical analysis of the samples indicated that the sodium fires produced mainly Na 2 O, and that the conversion of NaOH was slow. Comparison were made with COMRADEX-IV code models, which are appropriate for calculating deposition and concentrations for downwind distances between 10 2 and 10 4 m. (author)

Numerical simulation code for combustion of sodium liquid droplet and its verification

International Nuclear Information System (INIS)

Okano, Yasushi

1997-11-01

The computer programs for sodium leak and burning phenomena had been developed based on mechanistic approach. Direct numerical simulation code for sodium liquid droplet burning had been developed for numerical analysis of droplet combustion in forced convection air flow. Distributions of heat generation and temperature and reaction rate of chemical productions, such as sodium oxide and hydroxide, are calculated and evaluated with using this numerical code. Extended MAC method coupled with a higher-order upwind scheme had been used for combustion simulation of methane-air mixture. In the numerical simulation code for combustion of sodium liquid droplet, chemical reaction model of sodium was connected with the extended MAC method. Combustion of single sodium liquid droplet was simulated in this report for the verification of developed numerical simulation code. The changes of burning rate and reaction product with droplet diameter and inlet wind velocity were investigated. These calculation results were qualitatively and quantitatively conformed to the experimental and calculation observations in combustion engineering. It was confirmed that the numerical simulation code was available for the calculation of sodium liquid droplet burning. (author)

The toxicity and anesthetic effect of sodium hydroxybutyrate and ketamine at different periods of the combined radiation injuy , burn trauma and x-ray exposure

International Nuclear Information System (INIS)

Il'yuchenok, T.Yu.; Rasulev, B.K.; Moiseeva, L.A.

1985-01-01

Mongreal mice have been used to study animal sensitivity under the conditions of combined radiation injury (CRI), separate burn and X-ray effect to sodium hydroxybutyrate and ketamine. It is shown that while administering these anes thetics the differences in the organism reaction depend on the stage of injury and form of exposure. The changes in anesthesia duration in the first days (1-st - 4-th) after radiation exposure are contrary to those at combined radiation-thermal injury and separate burn trauma. The anesthetic effect of ketamine increases under the conditions of combined radiation-thermal injury and is not changed at separate exposures; its toxicity, on the contrary, on the 30-th day after burn and irradiation is increased

Sodium leak at Monju (II): Sodium leak, burning and aerosol behavior

International Nuclear Information System (INIS)

Funada, T.; Yamagishi, Y.

1996-01-01

The amount of leaked sodium was estimated as approximately 640 kg during the 220 minute leak. The ventilation duct and the walkway grating under the leak site were severely damaged by Na-Fe-O reaction, but the floor liner and the concrete wall were not. A total 100 kg of sodium aerosol was deposited in the reactor auxiliary building and 230 kg was released to the atmosphere. The sodium concentration at the site boundary was calculated as 0.05 mg/m 3 , NaOH equivalent, which was low in comparison with the permitted level of 2 mg/m 3 . The tritium quantity released was estimated as 4.4 x 10 7 Bq, which was about 0.03% of the average released value per month for a LWR. (author)

The combustion of sodium

International Nuclear Information System (INIS)

Newman, R.N.

1978-01-01

The burning rates of sodium in the form of vapour jets, droplets, sprays and unconfined and confined pools have been reviewed. Attention has been paid to assessing the value of models in the various combustion modes. Additional models have been constructed for the descriptions of laminar and turbulent vapour jets, stationary droplets, forced convection over ambient pool fires together with correlations for peak pressures in confined pool environments. Where appropriate experiments with sodium have not been conducted, the likely behaviour is predicted by comparison with the burning of other fuels, particularly in the field of large free ambient fires. Some areas where further knowledge is required are highlighted. (author)

Investigation for the sodium leak Monju. Sodium fire test-II

International Nuclear Information System (INIS)

Uchiyama, Naoki; Takai, Toshihide; Nishimura, Masahiro; Miyahara, Shinya; Miyake, Osamu; Tanabe, Hiromi

2000-08-01

As a part of the work for investigating the sodium leak accident which occurred in the Monju reactor (hereinafter referred to as Monju), sodium fire test-II was carried out using the SOLFA-1 (Sodium Leak, Fire and Aerosol) facility at OEC/PNC. In the test, the piping, ventilation duct, grating and floor liner were all full-sized and arranged in a rectangular concrete cell in the same manner as in Monju. The main objectives of the test were to confirm the leak and burning behavior of sodium from the damaged thermometer, and the effects of the sodium fire on the integrity of the surrounding structure. The main conclusions obtained from the test are shown below: (1) Burning Behavior of Leaked Sodium : Images taken with a cameras in the test reveal that in the early stages of the sodium leak, the sodium dropped down out of the flexible tube in drips. (2) Damage to the Ventilation Duct and Grating : The temperature of the ventilation duct's inner surface fluctuated between approximately 600degC and 700degC. The temperature of the grating began rising at the outset of the test, then fluctuated between roughly 600degC and 900degC. The maximum temperature was about 1000degC. After the test, damage to the ventilation duct and the grating was found. Damage to the duct was greater than that at Monju. (3) Effects on the Floor Liner : The temperature of the floor liner under the leak point exceed 1,000degC at 3 hours and 20 minutes into the test. A post test inspection of the liner revealed five holes in an area about 1m x 1m square under the leak point. There was also a decrease of the liner thickness on the north and west side of the leak point. (4) Effects on Concrete : The post test inspection revealed no surface damage on either the concrete side walls or the ceiling. However, the floor concrete was eroded to a maximum depth 8 cm due to a sodium-concrete reaction. The compressive strength of the concrete was not degraded in spite of the thermal effect. (5) Chemical

Installation for the suppression of sodium fires

International Nuclear Information System (INIS)

Newman, R.N.; Payne, J.F.B.; Lee, C.J.; Rowe, D.M.J.

1979-01-01

The basic operating principles are discussed of a passive baffle-catch tray fire suppression system for sodium fires. A new design is described incorporating increased compartmentalization of the collecting and drainage parts of the device. The burning and smoke generation rates from trays with varying aperture sizes were measured. From the experiments it was found that the burning rate and smoke generation rates could be related satisfactorily to the aperture areas. For the smallest aperture size ( 2 ) it was found that the smoke release was considerably less than that from a fire of the same area, because the smoke deposited on the underside of the baffle. A re-ignition problem was found, where pillars of sodium oxide (wicks) grow upward from the surface of the drained sodium and begin to burn when level with the baffle aperature. From a knowledge of the rate of growth of the wicks, trays may be made sufficiently deep to avoid the problem. Self acting valves were developed which allow the passage of sodium through the aperture and close when drainage is complete. These devices were shown to effect complete extinction of the drained sodium. Using the designs proposed it is possible to construct a system that will reduce the smoke emission from the drained sodium by a factor approaching 10 3 , without the use of valves, or with the self acting valves developed, reduce the emission from the drained sodium to approximately zero. (author)

Iodine release from sodium pool combustion

International Nuclear Information System (INIS)

Sagawa, N.; Fukushima, Y.; Yokota, N.; Akagane, K.; Mochizuki, K.

1979-01-01

Iodine release associated with sodium pool combustion was determined by heating 20 gr sodium containing sodium iodide, which was labelled with 131 I and dissolved in the sodium in concentration of 1∼1,000 ppm, to burn on a nickel crucible in conditioned atmosphere in a closed vessel of 0.4 m 3 . Oxygen concentration was changed in 5∼21% and humidity in 0∼89% by mixing nitrogen gas and air. Combustion products were trapped by a Maypack filter composed of particle filters, copper screens and activated charcoal beds and by a glass beads pack cooled by liquid argon. Iodine collected on these filter elements was determined by radio-gas chromatography. When the sodium sample burned in the atmosphere of air at room temperature, the release fractions observed were 6∼33% for sodium and 1∼20% for iodine added in the sodium. The release iodine was present in aerosol at a ratio of 98%, and the remainder in the gas form. The release fraction of iodine trended to decrease as oxygen concentration and humidity in the atmosphere increased. No organic iodide was detected in the combustion products. (author)

Licking as an out-of-hospital burns treatment-An isolated cultural phenomenon?

LENUS (Irish Health Repository)

Seoighe, Deirdre M

2012-02-01

Wound management in burns is a potentially complex issue. Salivary constituents have been shown experimentally to be of benefit in the treatment of thermal injuries. In our clinical experience we have encountered patients who have saliva directly applied to the burn wound prior to presenting to the national burns service. The practice is known as "Licking". We report two cases to illustrate the presentations we have encountered. We believe that these illustrate an isolated phenomenon unique to the Republic of Ireland.

Sodium hypochlorite poisoning

Science.gov (United States)

... that can cause choking and serious breathing problems. Symptoms of sodium hypochlorite poisoning may include: Burning, red eyes Chest pain Coma Coughing (from the fumes) Delirium Gagging sensation Low blood pressure Pain in the ...

Sodium fires and nuclear power station safety

International Nuclear Information System (INIS)

Ivanenko, V.N.; Zubin, A.; Drobyshev, A.V.

1986-01-01

The danger of sodium aerosol release at a design basis accident (DBA) of a sodium-cooled fast reactor that involves coolant leakage and burning, is being analyzed. It has been shown that radioactive and toxic releases at DBA do not exceed permissible values. Some means of sodium fire fighting are described. (author)

Porcine Burn Shock - Development of a Reliable Model and Response to Sodium, Water, and Plasma Loads Administered for Resuscitation

Science.gov (United States)

1973-06-01

nm.ddt. inital, Diet n*Mf) Thomas L. Wachtel, M.D. G. R. McCahan, Jr., D.V.M. 0 REPORT CATS 70. TOTAL No. Or PAGE Nb O. or mrs June 1973 - w 78 0. CON...observations of caloric uptake of pigskin, rise in temperature at the dermis-fat interface as a function of both time and skin surface temperature and an...of Iso-, Hypo - and Hypertonic Sodium Solutions in the Treatment of Burn Shock in Mice," Surgery, 57: 698-704, May 1965. 24. Rosenthal, S. M

Methodology for Extraction of Remaining Sodium of Used Sodium Containers

International Nuclear Information System (INIS)

Jung, Minhwan; Kim, Jongman; Cho, Youngil; Jeong, Jiyoung

2014-01-01

Sodium used as a coolant in the SFR (Sodium-cooled Fast Reactor) reacts easily with most elements due to its high reactivity. If sodium at high temperature leaks outside of a system boundary and makes contact with oxygen, it starts to burn and toxic aerosols are produced. In addition, it generates flammable hydrogen gas through a reaction with water. Hydrogen gas can be explosive within the range of 4.75 vol%. Therefore, the sodium should be handled carefully in accordance with standard procedures even though there is a small amount of target sodium remainings inside the containers and drums used for experiment. After the experiment, all sodium experimental apparatuses should be dismantled carefully through a series of draining, residual sodium extraction, and cleaning if they are no longer reused. In this work, a system for the extraction of the remaining sodium of used sodium drums has been developed and an operation procedure for the system has been established. In this work, a methodology for the extraction of remaining sodium out of the used sodium container has been developed as one of the sodium facility maintenance works. The sodium extraction system for remaining sodium of the used drums was designed and tested successfully. This work will contribute to an establishment of sodium handling technology for PGSFR. (Prototype Gen-IV Sodium-cooled Fast Reactor)

Sodium Bicarbonate mouth rinse: An Uncommon Complication

OpenAIRE

Fatih Mehmet Coskunses

2012-01-01

Sodium bicarbonate is a natural buffer that maintains a healthy pH in mouth to promote a clean and fresh oral environment. Sodium-bicarbonate rinse is empirically suggested to patients by dentist and people around, and may prove to be harmful. In this short communication, we present chemical burn of oral mucosa because of sodium-bicarbonate rinse after misfit dental impression.

Summary of HEDL sodium fire tests

International Nuclear Information System (INIS)

Hillard, R.K.

1978-10-01

The sodium fire test program and related studies at the Hanford Engineering Development Laboratory (HEDL) are described. The program is analytical and experimental in scope, with computer code development and experimental verification. Tests have ranged in size from gram quantity laboratory tests to 1600-kg sodium spills. The experimental work is performed in two facilities: the Large Sodium Fire Facility (LSFF) and the Containment Systems Test Facility (CSTF). Sodium fire extinguishment tests which verified the Fast Flux Test Facility (FFTF) secondary sodium fire protection system are described and related informaion on sodium burning rates and smoke release rates are correlated. The burning rates are compared to theoretical predictions based on heat and mass transfer analogy, with good agreement. Comparisons with the SOFIRE-II code are also made. Sodium combustion aerosol properties are defined as to chemical and physical nature, settling in closed vessels and effect of added water vapor. The HAA-3B aerosol behavior computer code is compared to tests in the 850-m 3 CSTF containment vessel. Sodium spray tests in the CSTF are compared with the SPRAY computer code. An air cleaning program is described, which has the objective of removing high mass concentration sodium combustion aerosols from vented cells and containment buildings. The aerosol mass holding capacity of commercial filters was measured and an aqueous scrubber system is described. The effects of sodium spills on cell structures were investigated, including water release from heated concrete, the reaction of sodium with concrete, the formation and spontaneous recombination of hydrogen, and the ability of steel cell liners to withstand large spills of high temperature sodium without leaking

Experimental study on combustion characteristics of sodium fire in a columnar flow

International Nuclear Information System (INIS)

Zhang Zhigang; Peng Kangwei; Guo Ming; Huo Yan

2014-01-01

In the operation of the sodium-cooled fast reactor, the accident caused by the leakage and combustion of liquid sodium is common and frequent in sodium-related facilities. This paper is based on an experimental study of sodium fire in a columnar flow, which was carried out to focus on the burning characteristics by analyzing the temperature fields in the burner. The injection of 200°C liquid sodium with the flux of 0.5 m 3 /h was poured into a 7.9 m 3 volume stainless steel cylindrical burner to shape a sodium fire, and the data of temperature fields in the burner have been collected by dozens of thermocouples which are laid in the combustion space and sodium collection plate. These results show that the sodium fire in a columnar flow is composed of the foregoing centered columnar fire, the subsequent spray fire caused by atomization and the pool fire on the collection plate. The temperature close to the burning sodium flow maximally reaches up to 950°C. The radial temperatures apart from the sodium flow are relatively low and generally about 200°C, and maximally just 300°C even when close to the sodium collection plate. The maximum temperature of the burning sodium dropping on the collection plate rises in the center of plate, about 528°C. This study is helpful to evaluate the combustion characteristics, formation process and composing forms of the sodium fire in the sodium-related facilities. (author)

NACOM - a code for sodium spray fire analysis

International Nuclear Information System (INIS)

Rao, P.M.; Kannan, S.E.

2002-01-01

Full text: In liquid metal fast breeder reactors (LMFBR), leakage of sodium can result in a spray fire. Because of higher burning rates in droplet form combustion of sodium in spray fire, thermal consequences are more severe than that in a sodium pool fire. The code NACOM was developed for the analysis of sodium spray fires in LMFBRs facilities. The code uses the validated model for estimating the falling droplet burning rates in pre-ignition and vapour phase combustion stages. It uses a distribution system to generate the droplet groups of different diameters that represent the spray. The code requires about 20 input parameters like sodium leak rates, sodium temperature, initial cell conditions like oxygen concentration, temperature and dimensions. NACOM is a validated code based on experiments with sodium inventory up to 650 kg in 0 to 21 % O 2 atmospheres. The paper brings out the salient features of the code along with the sensitivity analysis of the main input parameters like spray volume mean diameter, oxygen concentration etc. based on the results obtained. The limitations of the code and the confidence margins applicable to results obtained are also brought out

Sodium sampling and impurities determination

International Nuclear Information System (INIS)

Docekal, J.; Kovar, C.; Stuchlik, S.

1980-01-01

Samples may be obtained from tubes in-built in the sodium facility and further processed or they are taken into crucibles, stored and processed later. Another sampling method is a method involving vacuum distillation of sodium, thus concentrating impurities. Oxygen is determined by malgamation, distillation or vanadium balance methods. Hydrogen is determined by the metal diaphragm extraction, direct extraction or amalgamation methods. Carbon is determined using dry techniques involving burning a sodium sample at 1100 degC or using wet techniques by dissolving the sample with an acid. Trace amounts of metal impurities are determined after dissolving sodium in ethanol. The trace metals are concentrated and sodium excess is removed. (M.S.)

Analysis of patents on extinguishing agent for sodium fires

International Nuclear Information System (INIS)

Jeong, Ji Young; Jeong, K. C.; Kim, B. H.; Kim, T. J.; Choi, J. H.

2002-02-01

This report relates to the extinction of sodium fires, particularly where the burning sodium is in liquid form. The total of 14 patents on extinguishing agents for sodium fires patented from 1969 to 1997 are analyzed and summarized. All of the patents analyzed were issued from USA, France and Japan

Analysis of patents on extinguishing agent for sodium fires

Energy Technology Data Exchange (ETDEWEB)

Jeong, Ji Young; Jeong, K C; Kim, B H; Kim, T J; Choi, J H

2002-02-01

This report relates to the extinction of sodium fires, particularly where the burning sodium is in liquid form. The total of 14 patents on extinguishing agents for sodium fires patented from 1969 to 1997 are analyzed and summarized. All of the patents analyzed were issued from USA, France and Japan.

Burning mouth syndrome: an enigmatic disorder.

Science.gov (United States)

Javali, M A

2013-01-01

Burning mouth syndrome (BMS) is a chronic oral pain or burning sensation affecting the oral mucosa, often unaccompanied by mucosal lesions or other evident clinical signs. It is observed principally in middle-aged patients and postmenopausal women and may be accompanied by xerostomia and altered taste. Burning mouth syndrome is characterized by an intense burning or stinging sensation, preferably on the tongue or in other areas of mouth. This disorder is one of the most common, encountered in the clinical practice. This condition is probably of multifactorial origin; however the exact underlying etiology remains uncertain. This article discusses several aspects of BMS, updates current knowledge about the etiopathogenesis and describes the clinical features as well as the diagnosis and management of BMS patients.

Summary of HEDL sodium fire tests

International Nuclear Information System (INIS)

Hilliard, R.K.

1979-01-01

The sodium fire test program and related studies at the Hanford Engineering Development Laboratory (HEDL), covering the period from 1972 to 1978, are described. The program is analytical and experimental in scope, with computer code development and experimental verification. Tests have ranged in size from gram quantity laboratory tests to 1600-kg sodium spills. The experimental work is performed in two facilities: the Large Sodium Fire Facility (LSFF) and the Containment Systems Test Facility (CSTF). The facilities are described and the experimental results summarized. Sodium fire extinguishment tests which verified the Fast Flux Test Facility (FFTF) secondary sodium fire protection system are described and related information on sodium burning rates and smoke release rates are correlated. The burning rates are compared to theoretical predictions based on heat and mass transfer analogy, with good agreement. Comparisons with the SOFIRE-II code are also made. Sodium combustion aerosol properties are defined as to chemical and physical nature, settling in closed vessels and effect of added water vapor. The HAA-38 aerosol behaviour computer code is compared to tests in the 850-m 3 CSTF containment vessel. Sodium spray tests in the CSTF are compared with the SPRAY computer code. An air cleaning program is described, which has the objective of removing high mass concentration sodium combustion aerosols from vented cells and containment buildings. The aerosol mass holding capacity of commercial filters was measured and an aqueous scrubber system is described. The effects of sodium spills on cell structures were investigated, including water release from heated concrete, the reaction of sodium with concrete, the formation and spontaneous recombination of hydrogen, and the ability of steel cell liners to withstand large spills of high temperature sodium without leaking. (author)

Summary of HEDL sodium fire tests

Energy Technology Data Exchange (ETDEWEB)

Hilliard, R K [Hanford Engineering Development Laboratory, Richland, WA (United States)

1979-03-01

The sodium fire test program and related studies at the Hanford Engineering Development Laboratory (HEDL), covering the period from 1972 to 1978, are described. The program is analytical and experimental in scope, with computer code development and experimental verification. Tests have ranged in size from gram quantity laboratory tests to 1600-kg sodium spills. The experimental work is performed in two facilities: the Large Sodium Fire Facility (LSFF) and the Containment Systems Test Facility (CSTF). The facilities are described and the experimental results summarized. Sodium fire extinguishment tests which verified the Fast Flux Test Facility (FFTF) secondary sodium fire protection system are described and related information on sodium burning rates and smoke release rates are correlated. The burning rates are compared to theoretical predictions based on heat and mass transfer analogy, with good agreement. Comparisons with the SOFIRE-II code are also made. Sodium combustion aerosol properties are defined as to chemical and physical nature, settling in closed vessels and effect of added water vapor. The HAA-38 aerosol behaviour computer code is compared to tests in the 850-m{sup 3} CSTF containment vessel. Sodium spray tests in the CSTF are compared with the SPRAY computer code. An air cleaning program is described, which has the objective of removing high mass concentration sodium combustion aerosols from vented cells and containment buildings. The aerosol mass holding capacity of commercial filters was measured and an aqueous scrubber system is described. The effects of sodium spills on cell structures were investigated, including water release from heated concrete, the reaction of sodium with concrete, the formation and spontaneous recombination of hydrogen, and the ability of steel cell liners to withstand large spills of high temperature sodium without leaking. (author)

CLINICAL STUDY OF ELECTRICAL BURNS AMONG ALL BURNS CASES- 3 YEARS’ EXPERIENCE

Directory of Open Access Journals (Sweden)

Nagabathula Durga Prasad

2017-08-01

Full Text Available BACKGROUND With the advances in technology, electrical injuries are becoming more common and are the leading cause of work-related traumatic death. One third of all electrical traumas and most high-voltage injuries are job related and more than 50% of these injuries result from power line contact. The management of the major burn injury represents a significant challenge to every member of the burns team. Most of electrical burns present with gangrene of toes and limbs with eschar over body parts. Their presentation is mostly due to contact with high-voltage electricity at their work places. MATERIALS AND METHODS A retrospective study was made to study the clinico-social profile of patients suffering electric burns admitted into Department of General Surgery. RESULTS 92 cases were evaluated and studied. Majority of patients developed gangrene of limbs and toes. Amputations and skin grafting was done. Most patients who suffered electric burns were males of age group 21 to 40 years. All cases are accidental and mostly occurred at work places. Most electric burns are high-voltage based and caused deep burns. Major complications like acute renal failure and septicaemia were encountered. Most of them suffered 16 to 30% burns. Most commonly isolated organism from wounds is pseudomonas. Most of them suffered a hospital stay of 1 to 2 months. CONCLUSION Electric burns are a burden to the society. Prevention is the best way to deal with them. Electricity-based employees have to be trained properly regarding safety measures to be taken. General education of public regarding safety measures can prevent electrical burn injuries.

Camphor Burns on the Palm: An Unusual New Presentation

Directory of Open Access Journals (Sweden)

B A Ramesh

2018-01-01

Full Text Available Introduction: Camphor burns on the palm are uncommon and rarely encountered by a plastic surgeon. Aim: This study aims to analyze different patterns of camphor burns on the palm. Methods: Five women and one man presented with camphor burns on their palm. All patients had burns on their right palm. The shape of camphor, the duration of contact with the ignited camphor on the palm, and post-burn treatments were evaluated. Results: Three types of camphor burns were noted: Type 1 (a ring-shaped or a dome-shaped blister with unburned skin in the center, Type 2 (an oval-shaped partially thick burn with unburned skin in the center, and Type 3 (a full-thickness burn exposing the palmar fascia. Conclusion: Different types of camphor burns on the palm are described in this study. This is the first study to report ring-shaped blisters and ring-shaped partially thick camphor burns caused on the palm.

Sodium fires and its extinguishment; Gorenie, sredstva i sposoby tusheniya natriya

Energy Technology Data Exchange (ETDEWEB)

Mikhedov, V G

1979-03-01

The fire safety problems of NPP with sodium coolants in USSR are presented. The design of sodium reactors is made with premises with sodium coolants being hermetic and filled with nitrogen. Some engineering solutions of fire safety including design, elaboration and choice of construction and protection materials are presented. Some theoretical aspects of sodium burning are presented as well as methods of sodium fire extinguishing methods including the use of powder.

Extinguishing experiments of sodium fires carried out by TNO

International Nuclear Information System (INIS)

Meijer, G.J.A.M.; Rulkens, W.H.

1979-01-01

For the collection of burning sodium from the components and pipes of the secondary circuit of SNR 300, spill-trays are foreseen which are connected to dump tanks. These spill-trays are covered with a sieve in order to reduce the flow of air to the sodium in the spill-tray and hence to reduce the burning rate. In order to further minimize the consequences of a large sodium fire for the components, the licensing authority required as a back-up the installation of a remotely operated distribution system by means of which an extinguishing powder can be sprayed upon the spill-trays. Experiments were carried out in which the effectiveness of different extinguishing powders in combination with the sieve covered spill-trays were tested in a comparative manner. Attention was paid to the question whether such a spray system would have also additional benefits in the case of smaller sodium leaks. To this purpose three commercially available extinguishing powders were tested, one on a sodium chloride, two on a carbonate base. Also the effectiveness of the sieves proper with respect to reducing the burning rate was tested without applying any extinguishing powders. Finally for a reference some tests were done on open spill-trays, i.e. spill-trays not covered with a sieve.The investigations which were carried out in 1976-1977 were limited to fire experiments, aspects of transport of the powder in the distribution system were not investigated

Comparison between TRU burning reactors and commercial fast reactor

International Nuclear Information System (INIS)

Fujimura, Koji; Sanda, Toshio; Ogawa, Takashi

2001-03-01

additional consideration should be required in nuclear design and fuel treating facilities due to reactivity coefficient being shifted to the plus side, larger neutron yield and increased heat source caused by MA loading. (2) Confirmation of TRU burning reactor core concepts. The core specification of sodium cooled-nitride fueled TRU burning large reactor was designed based on commercial type fast reactor (sodium cooled nitride fueled large fast reactor, 38000 MWt) which was designed in the feasibility studies on commercialized fast reactor cycle system. The composition of MAs from LWR's spent fuel was supposed. MA content in the core fuel is settled to 60 wt% based on the JAERI's design in order to maximize the MA transmutation amount. We need to exchange 25% of core fuel with zirconium hydride (ZrH 1.6 ) to attain Doppler coefficient being equivalent to that of the conventional type commercial fast reactor loaded 5 wt% MA. Furthermore, this reactor could transmute MAs produced in forty-eight sodium cooled nitride fueled large fast reactors generating the same output. In order to investigate the dependency of MA transmutation characteristics on the reactor output, 1200 MWt TRU burning middle or small reactor core concept was designed. This core was settled by reducing the number of core fuel assemblies from that of TRU burning large reactor designed above. MA transmutation rate in this core is smaller than that in the TRU burning large reactor core because the neutron flux of this core becomes smaller than that of the TRU burning large reactor core due to the higher Pu enrichment. (3) Comparison between TRU burning reactor and conventional type commercial fast reactor. MA transmutation and nuclear characteristics of the sodium cooled nitride fuel commercial type fast reactor loaded 5 wt%MA were evaluated and compared with those of TRU burning large reactor designed in (2). The commercial type fast reactor could only transmute MAs produced in seven sodium cooled nitride

Decontamination of burns contaminated with radioactive materials

International Nuclear Information System (INIS)

Vykouril, L.

1986-01-01

The suitability of various solutions for the decontamination of burnt skin and their efficiency were tested by experiments on rats. Tested was the decontamination of undisturbed skin, second degree skin burns and third degree skin burns. Decontamination solutions used included: distilled water, jodonal (an aqueous solution of iodine, ethoxylated nonylphenols, the copolymer of ethylene oxide with propylene oxide, and phosphoric acid) and a decontamination mixture of Sapon, Komplexon (trade names of detergents) and sodium hexametaphosphate. Decontamination efficiency was 68.4% for second degree burns and 47.1% for third degree burns. Most effective was the decontamination solution with an efficiency of 72%; the efficiency of jodonal was 67% and of water - 54%. Jodonal is the most suitable: in addition, it acts as a disinfectant and antiseptic. (M.D.)

Epidemiology, etiology and outcomes of burn patients in a Referral Burn Hospital, Tehran

Directory of Open Access Journals (Sweden)

Mohammad Mehdi Soltan Dallal

2016-08-01

Full Text Available Background: Burns and its complications are regarded as a major problem in the society. Skin injuries resulted from ultraviolet radiation, radioactivity, electricity or chemicals as well as respiratory damage from smoke inhalation are considered burns. This study aimed to determine the epidemiology and outcome of burn patients admitted to Motahari Hospital, Tehran, Iran. Methods: Two hundred patients with second-degree burns admitted to Motahari Referral Center of Burn in Tehran, Iran. They were studied during a period of 12 months from May 2012 to May 2013. During the first week of treatment swabs were collected from the burn wounds after cleaning the site with sterile normal saline. Samples were inoculated in blood agar and McConkey agar, then incubation at 37 C for 48 hours. Identification was carried out according to standard conventional biochemical tests. Treatment continued up to epithelial formation and wound healing. Results of microbial culture for each patient was recorded. Healing time of the burn wounds in patients was recorded in log books. Chi-square test and SPSS Software v.19 (IBM, NY, USA were used for data analysis. Results: Our findings indicate that the most causes of burns are hot liquids in 57% of cases and flammable liquid in 21% of cases. The most cases of burns were found to be in the range of 21 to 30 percent with 17.5% and 7% in male and female respectively. Gram-negative bacteria were dominated in 85.7% and among them pseudomonas spp. with 37.5% were the most common cause of infected burns, followed by Enterobacter, Escherichia coli, Staphylococcus aureus, Acinetobacter and Klebsiella spp. Conclusion: The results of this study showed that the most cause of burns in both sex is hot liquid. Men were more expose to burn than women and this might be due to the fact that men are involved in more dangerous jobs than female. Pseudomonas aeruginosa was the most common organism encountered in burn infection.

Effect of turbulent natural convection on sodium pool combustion in the steam generator building of a fast breeder reactor

International Nuclear Information System (INIS)

Karthikeyan, S.; Sundararajan, T.; Shet, U.S.P.; Selvaraj, P.

2009-01-01

A computational model is proposed to simulate sodium pool combustion considering the effect of turbulent natural convection in a vented enclosure of the steam generator building (SGB) of a fast breeder reactor. The model is validated by comparing the simulated results with the experimental results available in literature for sodium pool combustion in a CSTF vessel. After validation, the effects of vents and the location of the pool on the burning rate of sodium and the associated heat transfer to the walls are studied in an enclosure comparable in size to one floor of the steam generator building. In the presence of ventilation, the burning rate of sodium increases, but the total heat transferred to the walls of the enclosure is reduced. It is also found that the burning rate of sodium pool and the heat transfer to the walls of the enclosures vary significantly with the location of sodium pool.

Destruction of mechanical structures by sodium fires

International Nuclear Information System (INIS)

Cherdron, W.

1992-01-01

With respect to pipe ruptures and leakages in liquid-metal fast breeder reactors, it can be assumed that relatively large amounts of liquid sodium will be poured or sprayed into an oxygen-containing atmosphere. Under reactor conditions, the sodium will burn immediately, leading to temperature and pressure rises in the containment, and the strong aerosol release may influence ventilation and filter systems. In addition to these consequences, which are well known, it must be taken into account that the sodium fire also attacks mechanical structures like steel and concrete. In the frame work of the sodium fire research program (FAUNA) at Kernforschungszentrum Karlsruhe, extensive experiments were performed to investigate the consequences of sodium pool, spray, and combined fires

Extinction of sodium fires

International Nuclear Information System (INIS)

Malet, J.C.; Spagna, F.

1989-01-01

This paper presents how, starting from a knowledge of sodium ignition and burning, principles for extinction (smothering catch trays, leak recuperation systems, powders) can be developed. These techniques applied in Superphenix 1 and PEC reactors have been tested in the ESMERALDA experimental program which is a joint French/Italian project. (author)

Review of the sodium fire experiments including sodium-concrete-reactions and summary of the results

International Nuclear Information System (INIS)

Cherdron, W.

1996-01-01

In the technical and design concept of containment systems of sodium cooled breeder reactors it has to be considered, that leakages in sodium pipes lead to sodium fires. The temperature and pressure rise caused by sodium fires makes it indispensable to analyse these accidents to be able to assess the safety of the whole system. Generally sodium leakages may lead to three different types of fires with different consequences. The main influences are the geometry of the leakage, shape, size, location, and the sodium conditions, such as temperature, flow rate and velocity. It must be also considered the reaction of sodium with surfaces like concrete. The paper gives an overview over all the sodium fire experiments performed in the FAUNA-facility (220 m 3 ) of the Forschungszentrum Karlsruhe in the years 1979 to 1993. The experimental program started with the investigation of pool fires on burning areas between 2 and 12 m 2 with up to 500 kg of Sodium. The experiments had been continued with 3 combined fires and 40 experiments on spray fires. 7 experiments on sodium-concrete reactions completed the program. (author)

An unusual electrical burn caused by alkaline batteries

Directory of Open Access Journals (Sweden)

Tyng-Luen Roan

2015-02-01

Full Text Available Electrical burns caused by low-voltage batteries are rarely reported. We recently encountered a male patient who suffered from a superficial second-degree burn over his left elbow and back. The total body surface area of the burn was estimated to be 6%. After interviewing the patient, the cause was suspected to be related to the explosion of a music player on the left-side of his waist, carried on his belt while he was painting a bathroom wall. Elevated creatine kinase levels and hematuria indicated rhabdomyolysis and suggested an electrical burn. Initial treatment was done in the burn intensive care unit with fluid challenge and wound care. The creatine kinase level decreased gradually and the hematuria was gone after 4 days in the intensive care unit. He was then transferred to the general ward for further wound management and discharged from our burn center after a total of 11 days without surgical intervention.

Friction and wear in sodium

International Nuclear Information System (INIS)

Hoffman, N.J.; Droher, J.J.

1973-01-01

In the design of a safe and reliable sodium-cooled reactor one of the more important problem areas is that of friction and wear of components immersed in liquid sodium or exposed to sodium vapor. Sodium coolant at elevated temperatures may severely affect most oxide-bearing surface layers which provide corrosion resistance and, to some extent, lubrication and surface hardness. Consequently, accelerated deterioration may be experienced on engaged-motion contact surfaces, which could result in unexpected reactor shutdown from component malfunction or failure due to galling and seizure. An overall view of the friction and wear phenomena encountered during oscillatory rubbing of surfaces in high-temperature, liquid-sodium environments is presented. Specific data generated at the Liquid Metal Engineering Center (LMEC) on this subject is also presented. (U.S.)

Methods for the sodium cooled fast reactor fire safety provisions

International Nuclear Information System (INIS)

Gryaznov, B.V.; Dergachev, N.P.

1983-01-01

Problems of fire safety provision on NPPs with sodium cooled fast reactor are under discussion. Methods of sodium leak localization, measures eliminating sodium flaring up during leaks and main means of sodium fire extinguishing are considered. An extinguishing of sodium flaring up is performed by means of sodium temperatUre decrease and by limitation of hydrogen access to the flaring up surface. A conclusion is made that the most effective methods of extinguishing are the following: self-extinguishing (due to hydrogen burning out in a limiting volume); extinguishing by a gas mixture of nitrogen and carbonic acid (initial filling and blowing of rooms during sodium flaring up); extinguishing by special powders

Investigation of sodium area conflagrations and testing of a protective system

Energy Technology Data Exchange (ETDEWEB)

Huber, F; Menzenhauer, P; Peppler, W [Kernforschungszentrum Karlsruhe (F.R. Germany). Inst. fuer Reaktorentwicklung

1975-12-01

During research and development work on the SNR-300 sodium-cooled fast reactor the consequences and confinement of sodium fires occurring in enclosures were studied. The behavior of liquid sodium during fires and the behavior of an inherently ready-for-operation protective system are described. Theoretical considerations on the behavior of burning liquid sodium are compared with experimental results. A protective system for large facilities is presented and the use of extinguishing powders is reviewed.

Analytical study of sodium combustion phenomena under sodium leak accidents

International Nuclear Information System (INIS)

Kim, Byung Ho; Jeong, J. Y.; Jeong, K. C.; Kim, T. J.; Choi, J. H.

2001-12-01

The rise of temperature and pressure, the release of aerosol in the buildings as a result of sodium fire must be considered for the safety measures of LMR. Therefore for the safety of the LMR, it is necessary to understand the characteristics of sodium fire, resulting from the various type of leakage. ASSCOPS(Analysis of Simultaneous Sodium Combustion in Pool and Spray) is the computer code for the analysis of the thermal consequence of sodium leak and fire in LMR that has been developed by Japan Nuclear Cycle Development Institute(JNC) in Japan. In this study, a preliminary analysis of sodium leak and fire accidents in S/G building of KALIMER is made by using ASSCOPS code. Various phenomena of interest are spray and pool burning, peak pressure, temperature change, local structure temperature, aerosol behavior, drain system into smothering tank, ventilation characteristics at each cell with the safety venting system and nitrogen injection system. In this calculation, the dimension of the S/G building was chosen in accordance with the selected options of LMR name KALIMER(Korea). As a result of this study, it was shown that subsequent effect of sodium fire depended upon whether the sodium continued to leak from the pipe or not, whether the ventilation system was running, whether the inert gas injection system was provided, whether the sodium on floor was drained into the smothering tank or not, whether the building was sealed or not, etc. Specially the excessive rise of pressure into each cell was prevented by installing the pressure release plates on wall of the building

Some aspects of sodium technology issued from the operating experience of RAPSODIE and PHENIX

International Nuclear Information System (INIS)

Kremser, J.; Lacroix, A.

1976-01-01

This paper deals with the experience on sodium technology gained from RAPSODIE and PHENIX operation. Problems encountered with sodium circuits, main components, handling equipment and instrumentation are discussed. Some information related to the contamination by radioactive products of sodium and sodium circuits is given

Fuel burn analysis of a sodium fast reactor with KANEXT and Serpent; Analisis de quemado de combustible de un reactor rapido de sodio con KANEXT y SERPENT

Energy Technology Data Exchange (ETDEWEB)

Lopez S, R. C.; Francois L, J. L., E-mail: rcarlos.lope@gmail.com [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Paseo Cuauhnahuac 8532, 62550 Jiutepec, Morelos (Mexico)

2015-09-15

The fast reactors cooled by sodium are one of the options considered in the Generation IV. Since most of the reactors of Fourth Generation are still in development stage, is necessary to have efficient and reliable computational tools, this in order to obtain accurate results in reasonable computational times. In this paper is introduced and describes the deterministic code KANEXT (KArlsruhe Neutronic EXtended Tool) and is compared against a Monte Carlo code of more diffusion: Serpent. KANEXT, being a modular code requires the interaction of different modules to perform a job, this interaction of modules is described in this article. The parameters to be compared are the results of the neutron multiplication effective factor and the evolution of isotopes during the burning. The mentioned comparison is carried out for a fast reactor cooled by sodium of relatively small size compared to commercial size reactors. In this paper the particularities of the reactor are described, important for the analysis such as geometry, enrichments, reflector, etc. The considerations in the implementation in both codes are also described, as are simplifications, length of the burning steps, possible solutions of the Bateman equations for the burning fuel in Serpent and the solution options for transport (P3) and diffusion (P1) in KANEXT. The results show good correspondence between Serpent and KANEXT, which give confidence to continue using KANEXT as the main tool. Respect to computation time, time saving is evident with the use of deterministic codes instead of Monte Carlo codes, in this particular case, the time savings using KANEXT is about 98.5% of the time used by Serpent. (Author)

Effects of sodium fires on structures and materials. Practical experience with sodium leakage accidents

International Nuclear Information System (INIS)

Freudenstein, K.F.

1989-01-01

A few sodium leakage, incidents happened in SNR 300 nuclear power plant during pre-nuclear operation which were of minor importance with respect to sodium fires. The most important sodium fire accident in the past happened in the Almeria Solar platform in Spain during the attempt to repair a valve while leaving accidentally the circuit under 4 bar overpressure. Considerable damage to pipes, valves, its insulation and its support structures was observed in the influence zone of the fire. Post accident analysis gave a leaked mass of about 14 m 3 , at a sodium temperature of 225 deg. C, the leakage lasting approximately half an hour, and burning under convective heat exchange with the external air in a section of 40 m 2 up to a height of 6 m down to the catch pans. Some local temperatures were determined by metallurgical means, integral support temperatures estimated from mechanical deformation observed. From these temperatures it was concluded that a massive spray type fire must have happened. The results fall in the interpretation range of sodium-spray fire test results. (author)

Study of burned optimization for minor actinides in European Sodium Fast Reactor (ESFR) by use of moderator materials

International Nuclear Information System (INIS)

Ramos, R L; Villanueva, A J; Buiront, L

2012-01-01

The minor actinides (MA) burn up optimization in the European Sodium Fast Reactor (ESFR) core was studied by adding different moderating materials in the Minor Actinides Bearing Blanket subassemblies (MABB SA) using the ERANOS neutron code package. These SA are of hexagonal shape and are composed of pellets inside of pins. These pellets contain a mixture of uranium dioxide (UO 2 ) and americium dioxide (AmO 2 ). If some of these pins are replaced by other identical ones containing moderating material instead of minor actinides, a shift in the spectrum towards lower energies is expected, which might enhance the burn up performance. The results of this work demonstrated that the use of compounds of hydrogen and magnesium as moderators produces a shift in the neutron spectrum, improving the porcentual minor actinides consumption. ZrH 2 moderator material was found to exhibit the best performances for this propose, followed by MgO and MgAl 2 O 4 , in that order. The use of SiC, BeO, TiC, LiO 2 and ZrC material produced no effect on the shift of the neutron spectrum. For safety reasons, it seems hardly realistic to use hydrogenous compounds in sodium fast reactors. So, compounds with magnesium are selected to be placed into the pins to improve the porcentual minor actinides consumption. The ESFR core is composed by 817 SA, 453 of them are fuel SA, 247 are reflectors SA, 84 are MABB (Minor Actinides Bearing Blankets) SA and 33 are control and shutdown rods. When about half of the total pins in each MABB were substituted by moderator pins with MgO pellets (135 of 271 pins), the porcentual consumption of minor actinides was of 30.85 %, i.e., 227.22 kg of minor actinides were consumed out of 736.65 kg in the initial configuration. In the case where all the pins of the MABB contained pellets of minor actinides, the porcentual consumption of minor actinides was of 21.26 %, i.e., 312.13 kg of minor actinides were consumed of 1467.87 kg in the initial configuration (author)

Sodium channel Nav1.7 immunoreactivity in painful human dental pulp and burning mouth syndrome

Directory of Open Access Journals (Sweden)

Yiangou Yiangos

2010-06-01

Full Text Available Abstract Background Voltage gated sodium channels Nav1.7 are involved in nociceptor nerve action potentials and are known to affect pain sensitivity in clinical genetic disorders. Aims and Objectives To study Nav1.7 levels in dental pulpitis pain, an inflammatory condition, and burning mouth syndrome (BMS, considered a neuropathic orofacial pain disorder. Methods Two groups of patients were recruited for this study. One group consisted of patients with dental pulpitis pain (n = 5 and controls (n = 12, and the other patients with BMS (n = 7 and controls (n = 10. BMS patients were diagnosed according to the International Association for the Study of Pain criteria; a pain history was collected, including the visual analogue scale (VAS. Immunohistochemistry with visual intensity and computer image analysis were used to evaluate levels of Nav1.7 in dental pulp tissue samples from the dental pulpitis group, and tongue biopsies from the BMS group. Results There was a significantly increased visual intensity score for Nav1.7 in nerve fibres in the painful dental pulp specimens, compared to controls. Image analysis showed a trend for an increase of the Nav1.7 immunoreactive % area in the painful pulp group, but this was not statistically significant. When expressed as a ratio of the neurofilament % area, there was a strong trend for an increase of Nav1.7 in the painful pulp group. Nav1.7 immunoreactive fibres were seen in abundance in the sub-mucosal layer of tongue biopsies, with no significant difference between BMS and controls. Conclusion Nav1.7 sodium channel may play a significant role in inflammatory dental pain. Clinical trials with selective Nav1.7 channel blockers should prioritise dental pulp pain rather than BMS.

Sodium channel Nav1.7 immunoreactivity in painful human dental pulp and burning mouth syndrome

Science.gov (United States)

2010-01-01

Background Voltage gated sodium channels Nav1.7 are involved in nociceptor nerve action potentials and are known to affect pain sensitivity in clinical genetic disorders. Aims and Objectives To study Nav1.7 levels in dental pulpitis pain, an inflammatory condition, and burning mouth syndrome (BMS), considered a neuropathic orofacial pain disorder. Methods Two groups of patients were recruited for this study. One group consisted of patients with dental pulpitis pain (n = 5) and controls (n = 12), and the other patients with BMS (n = 7) and controls (n = 10). BMS patients were diagnosed according to the International Association for the Study of Pain criteria; a pain history was collected, including the visual analogue scale (VAS). Immunohistochemistry with visual intensity and computer image analysis were used to evaluate levels of Nav1.7 in dental pulp tissue samples from the dental pulpitis group, and tongue biopsies from the BMS group. Results There was a significantly increased visual intensity score for Nav1.7 in nerve fibres in the painful dental pulp specimens, compared to controls. Image analysis showed a trend for an increase of the Nav1.7 immunoreactive % area in the painful pulp group, but this was not statistically significant. When expressed as a ratio of the neurofilament % area, there was a strong trend for an increase of Nav1.7 in the painful pulp group. Nav1.7 immunoreactive fibres were seen in abundance in the sub-mucosal layer of tongue biopsies, with no significant difference between BMS and controls. Conclusion Nav1.7 sodium channel may play a significant role in inflammatory dental pain. Clinical trials with selective Nav1.7 channel blockers should prioritise dental pulp pain rather than BMS. PMID:20529324

Burn Survivors' Perceptions regarding Relevant Sexual Education Strategies

Science.gov (United States)

Parrott, Yolan; Esmail, Shaniff

2010-01-01

Purpose: This paper aims to investigate the unique issues childhood burn survivors experience in relation to sex education and sexual development. Design/methodology/approach: Using a phenomenological approach, participants described their lived experiences with regards to sex education and the sexuality issues they encountered as child burn…

FORMULATION AND TECHNOLOGY DEVELOPMENT OF HERBAL PHENOLIC BIOPOLYMER-CONTAINING FILMS FOR BURN TREATMENT.

Science.gov (United States)

Gokadze, S; Barbakadze, V; Mulkijanyan, K; Bakuridze, A; Bakuridze, L

2017-06-01

Application of phytofilms based on biosolublepolymers is considered as a prospectivemethod for burn treatment . Herbal remedies contain biologically active substances, that are relatively less toxic, do not cause skin irritation or allergic reactions and, importantly, affectstrains of the microorganisms and viruses resistant to antibiotics and synthetic drugs. Nowadays, the advantages are given to such burn healing drugs, which along with high specific efficacy, have analgesic, anti-inflammatory and antimicrobial effects, and don't irritate the tissues. The mentioned peculiarities are characteristic for a new herbal phenolic biopolymer poly[3-(3,4-dihydroxyphenyl) glyceric acid](PDGA), isolated from the roots and stems of different comfrey species . The aim of the study was the development of the formulation and technology of biosoluble films for burn treatment on the basis of PDGA. The optimal content of phytofilm for burn healing was selected on the basis of the biopharmaceutical study results. The impact of the film-former on the quality, adhesion and moisture absorption of the phytofilmhas been studied. The optimal degree of the phytofilm moisture, determining its high adhesive properties,was established. The film prepared on the basis of sodium alginate, with 30.4% humidity, demonstrated the greatest adhesion strength. After investigation of the PDGA release it was found, that the hydrophilic bases such as: sodium carboxymethyl-cellulose (69.2%) andsodium alginate (78,65%) appeared to be optimal among the others. At the same time, taking into consideration the disadvantages of sodium carboxymethyl-cellulose (tautening effect on burnt surface, relatively low stability), a film based on sodium alginate has been chosen. The manufacturing technology for obtaining PDGA-containing phytofilm by casting is proposed. Theshelf-lifeofproposedPDGA-containingphytofilmis 2 years.

Numerical prediction of fire extinguishment characteristics of sodium leak collection tray in a fast breeder reactor

International Nuclear Information System (INIS)

Diwakar, S.V.; Mangarjuna Rao, P.; Kasinathan, N.; Das, Sarit K.; Sundararajan, T.

2011-01-01

Highlights: ► Sodium fire extinguishment in a leak collection tray is modeled by lumped approach. ► Hydrodynamics of liquid sodium on tray is emulated through a draining/sloshing model. ► Pool burning rates in the tray and holdup vessel are numerically estimated. ► The model directly yields the mass of sodium recovered after extinction of fire. ► Model predictions are in reasonable agreement with the available experimental data. - Abstract: Sodium leak collection tray (LCT) is an efficient passive device used for the extinguishment of liquid sodium fire in case of an accidental leakage from the secondary circuit of a fast breeder reactor. The LCT essentially isolates the leaking sodium into closed containers where the resulting fire is extinguished due to limited availability of oxygen. The current work aims to highlight the combustion extinguishment characteristics of LCT through a lumped formulation by conserving the mass and energy of liquid sodium and constituent gases in various parts of the LCT. Here, the complex hydrodynamics of liquid sodium is emulated through a semi-analytical draining/sloshing model and its burning rates are predicted through a three-dimensional open pool combustion model for the tray region and a closed pool combustion model for the holdup vessel. These simulations evaluate the burning rates at discrete levels of liquid sodium which are subsequently interpolated to establish correlations involving instantaneous liquid levels and oxygen concentration. Using the correlations obtained from the draining and combustion models, the overall lumped formulation directly predicts the un-burnt sodium recoverable after the extinguishment of fire in the LCT. The predicted results of this model compare well with the available experimental data.

Thermodynamic consequences of sodium leaks and fires in reactor containments

International Nuclear Information System (INIS)

Cherdron, W.; Jordan, S.

1989-01-01

In the technical and design concept of containment systems of sodium cooled breeder reactors due consideration must be given to the fact, that sodium penetration through leakages leads to sodium fires. The temperature and pressure rise caused by sodium fires makes it indispensable to analyze these accidents to be able to asses the safety of the whole system. To study the thermodynamic consequences of sodium leaks and fires, a long series of experiments on pool fires, spray fires and combined fires has been performed in the FAUNA-facility. In the pool fire experiments the pool area has been varied between 2 m 2 and 12 m 2 , with up to 500 kg of sodium at 500 deg. C inlet temperature. Burning rates between 20 and 40 kg Na/m 2 /h, depending on the particular conditions, can be stated for such types of fires. Combined fires, simulating a leakage through an insulation, have been investigated using a special sodium outlet 6 m above a 12 m 2 burning pan. The sodium flow ejection rate in these experiments covered the range of 50 up to 710 gr Na/sec, the maximum total amount of sodium released into the FAUNA vessel was 810 kg. The consequences of combined fires cover the range between pool fires and spray fires. The sodium spray fires were performed using a sodium spray system (150 liters of sodium at 500 deg. C and up to 6 bars overpressure), installed in the FAUNA containment, ejecting the sodium vertically upwards towards the impact plate at the top of the containment. In a series of experiments the spray nozzles have been varied from circular holes to sharp and rough edged slits, the flow rate covered the range from 0.8 kg Na/sec up to 56 Na/sec. It has been found that the nozzle design influences somewhat the course of the pressure increase, but the maximum overpressure is mainly determined by the sodium flow rate and the amount of sodium ejected. (author)

An Advanced Sodium-Cooled Fast Reactor Core Concept Using Uranium-Free Metallic Fuels for Maximizing TRU Burning Rate

Directory of Open Access Journals (Sweden)

Wuseong You

2017-12-01

Full Text Available In this paper, we designed and analyzed advanced sodium-cooled fast reactor cores using uranium-free metallic fuels for maximizing burning rate of transuranics (TRU nuclides from PWR spent fuels. It is well known that the removal of fertile nuclides such as 238U from fuels in liquid metal cooled fast reactor leads to the degradation of important safety parameters such as the Doppler coefficient, coolant void worth, and delayed neutron fraction. To resolve the degradation of the Doppler coefficient, we considered adding resonant nuclides to the uranium-free metallic fuels. The analysis results showed that the cores using uranium-free fuels loaded with tungsten instead of uranium have a significantly lower burnup reactivity swing and more negative Doppler coefficients than the core using uranium-free fuels without resonant nuclides. In addition, we considered the use of axially central B4C absorber region and moderator rods to further improve safety parameters such as sodium void worth, burnup reactivity swing, and the Doppler coefficient. The results of the analysis showed that the final design core can consume ~353 kg per cycle and satisfies self-controllability under unprotected accidents. The fuel cycle analysis showed that the PWR–SFR coupling fuel cycle option drastically reduces the amount of waste going to repository and the SFR burner can consume the amount of TRUs discharged from 3.72 PWRs generating the same electricity.

Radioimmunoassay of sodium cromoglycate in human plasma

Energy Technology Data Exchange (ETDEWEB)

Brown, K; Gardner, J J; Lockley, W J.S.; Preston, J R; Wilkinson, D J [Fisons plc, Loughborough (UK). Pharmaceutical Div.

1983-01-01

A sensitive radioimmunoassay method for sodium cromoglycate in human plasma is described. The lowest quantifiable concentration of sodium cromoglycate is 0.93 nmol/l when 0.1 ml plasma samples are analysed. The range of the method is limited; both 0.01 and 0.1 ml volumes of plasma must be analysed to encompass the concentration range 0.93-139 nmol/l which may be encountered in plasma samples from patients and human volunteers. The method is specific for sodium cromoglycate as indicated by a low cross-reactivity of the anti-cromoglycate antiserum with a number of drugs.

Improved modelling of sodium-spray fires and sodium-combustion aerosol chemical evolution - 15488

International Nuclear Information System (INIS)

Mathe, E.; Kissane, M.; Petitprez, D.

2015-01-01

In the context of the Generation IV Initiative, the consequences of a severe-accident in sodium-cooled fast reactor (SFR) must be studied. Being pyrophoric, sodium will burn upon contact with air in a containment creating toxic aerosols and we must take into account these fire aerosols when assessing the source term. We have developed a numerical simulation named NATRAC to calculate the mass of aerosols produced during a spray fire in a SFR severe accident. The results show that the mass of oxide aerosols can involve more than 60% of the ejected sodium. In a second part we have developed a numerical simulation named STARK based on the Cooper model that models the physico-chemical transformations of the aerosols. However, this model has never been validated and the literature does not permit to do so. In these conditions, we have designed and performed our own experiment ESSTIA to obtain the missing values of the parameters that govern Cooper model. The modified Cooper model we propose with the new parameters reproduces correctly the ESSTIA experimental data. The only parameter that has not yet been measured is the tortuosity of the sodium-fire aerosols surface layers. A dedicated experiment using real sodium-fire aerosols could eliminate any doubts about the uncertainty of the proposed Cooper model

CP ESFR: Collaborative Project for a European Sodium Fast Reactor Core studies

International Nuclear Information System (INIS)

Buiron, L.; Vasile, A.; Sunderland, R.

2013-01-01

• Significant progress has been made in optimizing both the oxide and carbide ESFR cores; • For the oxide core the optimisation process concentrated on the reduction of the sodium void reactivity effect and on the evaluation of MA burning performances. The CONF2 axial configuration has provided a significant overall reduction of the sodium void reactivity effect. • The carbide core had a significantly higher reactivity loss over the fuel cycle compared to the oxide one. By increasing slightly the fuel pin diameter, whilst still retaining the advantages of lower fuel temperatures of carbide fuel, and making changes in the core layout, the reactivity loss over the cycle has been reduced to a level similar to that of the oxide core. By adopting the CONF2 axial configuration initially developed for the oxide core, the sodium void reactivity of the carbide core has also been reduced appreciably. • The MA transmutation performances of the optimized ESFR oxide core have been investigated with respect to two boundary configurations. The HET2 configuration shows a low MA transmutation rate sufficient to burn the MA produced by the ESFR core without affecting the safety parameters. The HOM4 configuration (where 4%wt. MA are loaded homogeneously in each core SA) is the most challenging configuration due to its impact on safety coefficients but it shows an high MA burning rate suitable for burning also MA accumulated by a thermal reactor fleet

Fast reactor sodium systems operation experience and 'leak-before-break' criterion

International Nuclear Information System (INIS)

Ivanenko, V.N.; Zybin, V.A.

1996-01-01

In the paper sodium leakage detection systems used at fast reactors are described. Requirements on their main characteristics (sensitivity, response lime) are formulated. Results of tests are presented on studying the parameters of sodium leak detection systems including experiments on the measurement of size distribution of aerosol particles that have passed through sodium systems thermal insulation after leak initiation. Comparison of these data with dispersion of particles formed at free burning is carried out. Experience of real leaks that occurred at fast reactor sodium systems is analyzed. It has been shown that initiation and development of real leaks do not always follow the theoretical scheme. A substantial role of human factor for sodium systems reliability relative to sodium leaks is stressed. (author)

Flame photometric detection of sodium leaks: Tests on a fullscale model for the control gear sodium rig

International Nuclear Information System (INIS)

Grundy, B.R.; Knowles, P.

1971-01-01

The proposed arrangement for detecting sodium leaks from the large flanges of the Control Gear Sodium Rig (Test Section No. 8, MCTR) at REML is to jacket then in a secondary containment from which air samples will be continuously pumped. Pipework feeds the air to a flame photometer which responds if soditun is present. To prove that sodium smoke could be transferred through the system, tests were performed on a fullscale model by burning small amounts of sodium in different jackets. Large signals free from fluctuations were obtained in all tests, peak response occurring in 2 1/4 minutes or less. The signal quickly cleared after isolating the appropriate vessel. A waiting period of several hours was sufficient to reduce the signal to zero, no cleaning of pipework, etc being necessary. In contrast, samples of two lagging materials heated to 400 °C gave no response with the photometer at maximum sensitivity. (author)

Development of a Consistent and Reproducible Porcine Scald Burn Model

Science.gov (United States)

Kempf, Margit; Kimble, Roy; Cuttle, Leila

2016-01-01

There are very few porcine burn models that replicate scald injuries similar to those encountered by children. We have developed a robust porcine burn model capable of creating reproducible scald burns for a wide range of burn conditions. The study was conducted with juvenile Large White pigs, creating replicates of burn combinations; 50°C for 1, 2, 5 and 10 minutes and 60°C, 70°C, 80°C and 90°C for 5 seconds. Visual wound examination, biopsies and Laser Doppler Imaging were performed at 1, 24 hours and at 3 and 7 days post-burn. A consistent water temperature was maintained within the scald device for long durations (49.8 ± 0.1°C when set at 50°C). The macroscopic and histologic appearance was consistent between replicates of burn conditions. For 50°C water, 10 minute duration burns showed significantly deeper tissue injury than all shorter durations at 24 hours post-burn (p ≤ 0.0001), with damage seen to increase until day 3 post-burn. For 5 second duration burns, by day 7 post-burn the 80°C and 90°C scalds had damage detected significantly deeper in the tissue than the 70°C scalds (p ≤ 0.001). A reliable and safe model of porcine scald burn injury has been successfully developed. The novel apparatus with continually refreshed water improves consistency of scald creation for long exposure times. This model allows the pathophysiology of scald burn wound creation and progression to be examined. PMID:27612153

Sodium removal by alcohol process: Basic tests and its application

International Nuclear Information System (INIS)

Nakai, S.; Yamamoto, S.; Akai, M.; Yatabe, T.

1997-01-01

We have various methods for sodium removal; an alcohol cleaning process, a steam cleaning process and a direct burning process. Sodium removal by the alcohol process has a lot of advantages, such as causing no alkali corrosion to steel, short processing time and easy operation. Therefore the alcohol process was selected for the 1MWt double wall tube straight type steam generator. We have already had some experiences of the alcohol process, while still needed to confirm the sodium removal rate in the crevice and to develop an on-line sodium concentration monitoring method in alcohol during sodium removal. We have conducted the small scale sodium removal test with flowing alcohol where the sodium removal rate in the crevice and the alcohol conductivity were measured as functions of sodium concentration in alcohol and alcohol temperature. The sodium removal of the DWTSG was conducted by the devised alcohol process safely and efficiently. The process hour was about 1 day. Visual inspection during dismantling of the DWTSG showed no evidence of any un-reacted sodium. (author)

Degradation behavior of limestone concrete under limited time sodium exposure

International Nuclear Information System (INIS)

Das, S.K.; Sharma, A.K.; Ramesh, S.S.; Parida, F.C.; Kasinathan, N.; Chellapandi, P.

2009-01-01

Adequate safety measures are taken during design, fabrication, construction and operation of liquid sodium cooled fast breeder reactor (FBR). However, possibility of sodium leak from secondary heat transport circuits of FBR has not been completely ruled out. In the areas housing sodium pipelines such as Steam Generator Building (SGB), spilled liquid sodium not only reacts with air causing fire but also interacts with structural concrete resulting in its degradation. The structural concrete can be protected from sodium attack using sodium resistant sacrificial concrete layer or steel/refractory liners. Moreover, design and construction of sloping floor with sodium collection pit helps in minimizing the mass of sodium accumulated on the floor and exposure period. Sacrificial concrete layer on the structural concrete should meet key factors like economy, castability, easy removal of affected concrete in the event of a sodium fire and disposability of debris apart from its good resistance against hot burning sodium. Present study is directed towards testing of limestone concrete blocks (made out of 13% ordinary portland cement, 8% water, 48% coarse limestone and 31 % fine limestone aggregates)

Psychiatric Assessment and Rehabilitation of Burn Patients

Directory of Open Access Journals (Sweden)

Süleyman Akarsu

2017-03-01

Full Text Available Objective: Psychiatric rehabilitation has gained significance owing to improved healthcare facilities for burn injuries and decreased mortality/ morbidity rates. Burn traumas may result in psychiatric signs such as denial, anger, guilt, confusion, disgrace, anxiety, distress, and nervousness. Psychiatric disorders such as delirium, depression, anxiety, post-traumatic stress disorder, and sexual problems can also be encountered. Therefore, it is necessary to look for these signs and disorders through regular sessions with burn patients and appropriate psychometric tests. This study aims at examining the process of psychological rehabilitation for burn patients in light of the current literature. Material and Methods: This study has been carried out in the light of the main and current literature review. The study intends to put forth the data observed in the course of the psychological diagnosis, treatment and rehabilitation of burn patients. The study has been conducted in accordance with the Helsinki Declaration Guidelines. Results: Treatment and rehabilitation process requires a multidisciplinary teamwork that consists of physicians, dieticians, psychologists, social service specialists, and other healthcare workers who can meet the needs of burn patients and their families. It is necessary for the team to contribute both to the hospitalization process and the social environment of the patients and their families. Conclusion: It is observed that the quality of life of these patients can be considerably improved with the effective assessment of psychiatric signs that occur during or after the injury and with appropriate treatment methods.

Experimental study of sodium fires on concrete based on the sodium-concrete reaction and its consequences: study of the behavior of various concretes under metallic sheaths

International Nuclear Information System (INIS)

Berlin; Colome, J.; Malet, J.C.

The problem created by the violent reaction between hot sodium and concrete has only recently been recognized. Its importance was evidenced during experiments in which the sodium-barium oxide concrete reactions led to violent explosions. SESR approached this question during its experimental programs Cassandre and Lucifer. The Cassandre 01 experiment demonstrated the sodium-ordinary concrete reaction, where sodium was burned directly in a concrete vat. The consequences of this fire, pulverization of sodium particles, explosions and deterioration of the concrete led to consideration of protecting the concrete. Among possible shieldings sheath metal appeared to be the safest solution. The Cassandre 08, Lucifer 01 and Lucifer 04 experiments were used to study the behavior of various qualities of concrete protected from fire by a metal wall. The results show that a metal cladding efficiently protects concrete from sodium leaks

Technology for analysis of sodium pool fire characteristics

Energy Technology Data Exchange (ETDEWEB)

Kim, Byung Ho; Jeong, K C; Jeong, J Y; Kim, T J; Choi, J H; Choi, Y D; Hwang, S T

2000-09-01

Basic and detail design for medium sodium fire test facility was carried out and medium sodium fire test facility was constructed. Design data is as follows. - Test cell material : Concrete with high strength - Test cell dimension ; 48m{sup 3} (3x4x4m) - Design temp. ; 700 deg C - Operation temp. ; 530 deg C - Design pressure ; 1 bar (max.) - Dimension(Inside) : 3 x 4 x 4(m) - Test cell thickness ; 45cm - Liner plate with (Thickness : 3mm) In this study, sodium fire characteristics was analyzed and data for validation of computer code was produced. Oxygen and sodium filled in pool pan didn't burns instantly, but pool fire occurred through pre-ignition. Distribution of temperature in test cell was divided by two parts, and temperature at upper position appeared to be higher than temperature at lower position. The temperature in test cell increased with the feed of sodium. The pressure in test cell increased with the feed of sodium. When the feed of sodium was 8kg, peak pressure was 0.075 bar. Peak temperature in sodium pool appeared to be 854 deg C regardless of the feed of sodium. Decrease of 1% in oxygen concentration showed the rise of 0.036bar in pressure.

Technology for analysis of sodium pool fire characteristics

International Nuclear Information System (INIS)

Kim, Byung Ho; Jeong, K. C.; Jeong, J. Y.; Kim, T. J.; Choi, J. H.; Choi, Y. D.; Hwang, S. T.

2000-09-01

Basic and detail design for medium sodium fire test facility was carried out and medium sodium fire test facility was constructed. Design data is as follows. - Test cell material : Concrete with high strength - Test cell dimension ; 48m 3 (3x4x4m) - Design temp. ; 700 deg C - Operation temp. ; 530 deg C - Design pressure ; 1 bar (max.) - Dimension(Inside) : 3 x 4 x 4(m) - Test cell thickness ; 45cm - Liner plate with (Thickness : 3mm) In this study, sodium fire characteristics was analyzed and data for validation of computer code was produced. Oxygen and sodium filled in pool pan didn't burns instantly, but pool fire occurred through pre-ignition. Distribution of temperature in test cell was divided by two parts, and temperature at upper position appeared to be higher than temperature at lower position. The temperature in test cell increased with the feed of sodium. The pressure in test cell increased with the feed of sodium. When the feed of sodium was 8kg, peak pressure was 0.075 bar. Peak temperature in sodium pool appeared to be 854 deg C regardless of the feed of sodium. Decrease of 1% in oxygen concentration showed the rise of 0.036bar in pressure

Technology for analysis of sodium pool fire characteristics

Energy Technology Data Exchange (ETDEWEB)

Kim, Byung Ho; Jeong, K. C.; Jeong, J. Y.; Kim, T. J.; Choi, J. H.; Choi, Y. D.; Hwang, S. T

2000-09-01

Basic and detail design for medium sodium fire test facility was carried out and medium sodium fire test facility was constructed. Design data is as follows. - Test cell material : Concrete with high strength - Test cell dimension ; 48m{sup 3} (3x4x4m) - Design temp. ; 700 deg C - Operation temp. ; 530 deg C - Design pressure ; 1 bar (max.) - Dimension(Inside) : 3 x 4 x 4(m) - Test cell thickness ; 45cm - Liner plate with (Thickness : 3mm) In this study, sodium fire characteristics was analyzed and data for validation of computer code was produced. Oxygen and sodium filled in pool pan didn't burns instantly, but pool fire occurred through pre-ignition. Distribution of temperature in test cell was divided by two parts, and temperature at upper position appeared to be higher than temperature at lower position. The temperature in test cell increased with the feed of sodium. The pressure in test cell increased with the feed of sodium. When the feed of sodium was 8kg, peak pressure was 0.075 bar. Peak temperature in sodium pool appeared to be 854 deg C regardless of the feed of sodium. Decrease of 1% in oxygen concentration showed the rise of 0.036bar in pressure.

Simple experiments studying the catastrophic corrosion of stainless steel caused by sodium leaks

International Nuclear Information System (INIS)

Mathison, J.; Trevalion, P.A.; Hamer, A.N.

1971-01-01

Under certain conditions, small quantities of soditum escaping through a small hole may cause extensive corrosion and cratering on the outside of the containment in the vicinity of the leak and there is a possibility that this might lead to a major rupture of the containment. It is difficult to estimate such a corrosion rate by conducting post mortems after an incident because of the lack of precise information about times and temperatures. Simple sodium burning experiments have therefore been carried out in an attempt to provide rough quantitative data on the size of these corrosion rates. These showed that the average rate of corrosion of specimens of 18.8.1 stainless steel beneath a burning pool of sodium was of the order of 0.05 cm/hr at 600 ° C and 0.005 cm/hr at 400 ° C. Enhanced corrosion occurs at the periphery of the burning sodium. The rate of penetration will depend on the shape of the corrosion profile which exists in the affected surface. The times needed to penetrate different wall thicknesses of stainless steel pipework have been calculated for various corrosion profiles similar to those which have been observed after incidents in REML. (author)

Studies on release and deposition behaviour of cesium from contaminated sodium pools and cesium trap development for FBTR

International Nuclear Information System (INIS)

Sahoo, P.; Kannan, S.E.; Muralidharan, P.; Chandran, K.

1996-01-01

Investigations were carried out on the release and deposition behaviour of cesium from sodium pools in air-filled chamber in the temperature range of 673 to 873 K, using Cs-134 to simulate Cs-137. About 0.12 kg of sodium was loaded in a burn-pot together with 92.5 kBq of cesium. Experiments were carried out with 21% oxygen. Natural burning period of sodium and specific activity ratio between cesium and sodium showed a tendency to decrease and release fractions of both the species tended to increase with temperature. From the surface deposited aerosols it was observed that cesium has propensity to settle down closer to the point of release. A cesium trap has been developed for FBTR with RVC as getter material. Absorption kinetics and particle release behaviour studies pointed to its intended satisfactory performance in the plant. (author)

The Attack on Psychosomatic Integrity: a Study of the Psychological Sequelae of Burn Trauma

Science.gov (United States)

Cavaleri, V.; Epifanio, M.S.; Benigno, A.; Conte, F.; Di Pasquale, A.

2009-01-01

Summary Burns pathology is characterized not only by insidious damage to the patients' outward appearance but also by the equally painful emotional difficulties they encounter as they reorganize their identity and their personal history. This exploratory survey, combining research work with medical action, considers the cases of 41 outpatients who were hospitalized and subjected to skin grafting. The patients were recruited through the database of the Palermo Civic Hospital Plastic Surgery and Burns Therapy Operative Unit. The questionnaires were compiled 6 and 12 months post-burn (12 months' observation). The main objective of the research was to investigate the quality of life of burn patients in relation to the way they handled their condition on the emotional level, in order to cope with the stress caused by the burn. PMID:21991160

Exothermic potential of sodium nitrate salt cake

International Nuclear Information System (INIS)

Beitel, G.A.

1977-06-01

High-Level radioactive liquid waste is being reduced to a liquid slurry by an evaporation and crystallization process and stored in the existing single-shell tanks. Continuous pumping of the waste storage tank will reduce the present 30 to 50% moisture to the minimum possible. The reduced waste is a relatively immobile salt cake consisting predominantly of sodium nitrate (NaNO 3 ) with lesser amounts of sodium nitrite (NaNO 2 ), sodium metaaluminate (NaAlO 2 ), and sodium hydroxide (NaOH). Trace amounts of fission products, transuranics, and a broad spectrum of organic materials in small but unknown amounts are also present. A program was initiated in 1973 to determine whether or not conditions exist which could lead to an exothermic reaction in the salt cake. Results of the latest series of tests conducted to determine the effects of mass and pressure are summarized. Hanford salt cake, as stored, cannot support combustion, and does not ignite when covered with a burning volatile hydrocarbon

Release of fission products from contaminated sodium fires

International Nuclear Information System (INIS)

Jordan, S.

1976-01-01

Leaks in the primary coolant system of a LMFBR and also serious incidents with tank rupture may entail the escape of fission products into the containment of the reactor. For incident analysis it is important to know the retention capability of sodium for the different fission products. The release of cesium and strontium from pools contaminated with 100 to 1000 ppM was investigated by experiments. The cesium content of airborne aerosols depends on oxygen concentration: at 21 percent oxygen concentration the Cs content of sodium-oxide aerosols is 3 times and at 0.5 percent 15 times as high as the initial Cs concentration in the pool. Strontium content of aerosols over burning contaminated sodium pools is 10 3 times smaller than the strontium pool concentration

Operating experience of RAPSODIE and PHENIX relating to sodium aerosols and vapours

Energy Technology Data Exchange (ETDEWEB)

Delisle, J P; Reboul, M; Elie, X [DRNR/STRS - Centre de Cadarache, Saint-Paul-lez-Durance (France)

1977-01-01

The main difficulties resulting from sodium aerosols and vapours in the cover gas which have been encountered for 10 years in RAPSODIE and for 3 years in PHENIX are reviewed: condensation of sodium in annular spaces; plugging in primary gas pipes; plugging of filters and vapour traps. All those problems were easily overcome. (author)

Validation of CONTAIN-LMR code for accident analysis of sodium-cooled fast reactor containments

Energy Technology Data Exchange (ETDEWEB)

Gordeev, S.; Hering, W.; Schikorr, M.; Stieglitz, R. [Inst. for Neutron Physic and Reactor Technology, Karlsruhe Inst. of Technology, Campus Nord (Germany)

2012-07-01

CONTAIN-LMR 1 is an analytical tool for the containment performance of sodium cooled fast reactors. In this code, the modelling for the sodium fire is included: the oxygen diffusion model for the sodium pool fire, and the liquid droplet model for the sodium spray fire. CONTAIN-LMR is also able to model the interaction of liquid sodium with concrete structure. It may be applicable to different concrete compositions. Testing and validation of these models will help to qualify the simulation results. Three experiments with sodium performed in the FAUNA facility at FZK have been used for the validation of CONTAIN-LMR. For pool fire tests, calculations have been performed with two models. The first model consists of one gas cell representing the volume of the burn compartment. The volume of the second model is subdivided into 32 coupled gas cells. The agreement between calculations and experimental data is acceptable. The detailed pool fire model shows less deviation from experiments. In the spray fire, the direct heating from the sodium burning in the media is dominant. Therefore, single cell modeling is enough to describe the phenomena. Calculation results have reasonable agreement with experimental data. Limitations of the implemented spray model can cause the overestimation of predicted pressure and temperature in the cell atmosphere. The ability of the CONTAIN-LMR to simulate the sodium pool fire accompanied by sodium-concrete reactions was tested using the experimental study of sodium-concrete interactions for construction concrete as well as for shielding concrete. The model provides a reasonably good representation of chemical processes during sodium-concrete interaction. The comparison of time-temperature profiles of sodium and concrete shows, that the model requires modifications for predictions of the test results. (authors)

Thermal fluctuation problems encountered in LMFRs

International Nuclear Information System (INIS)

Gelineau, O.; Sperandio, M.; Martin, P.; Ricard, J.B.; Martin, L.; Bougault, A.

1994-01-01

One of the most significant problems of LMFBRs deals with thermal fluctuations. The main reason is that LMFBRs operate with sodium coolant at very different temperatures which leads to the existence of several areas of transition between hot and cold sodium. These transitions areas which are the critical points, maybe found in the reactor block as well as in the secondary and auxiliary loops. The characteristics of these thermal fluctuations are not easy to quantify because of their complex (random) behaviour, and often demand the use of thermalhydraulic mock-up tests. A good knowledge of these phenomena is essential because of the potential high level of damage they can induce on structures. Two typical thermal fluctuation problems encountered on operation reactors are described. They were not originally anticipated at the design stage of the former Phenix and the latter Superphenix reactors. Description and the analyses performed to describe the damaging process are explained. A well known thermal fluctuation problem is presented. It is pointed out how the feedback from the damages observed on operating reactors is used to prevent the components from any high cycle fatigue

Numerical modeling of sodium fire – Part II: Pool combustion and combined spray and pool combustion

International Nuclear Information System (INIS)

Sathiah, Pratap; Roelofs, Ferry

2014-01-01

Highlights: • A CFD based method is proposed for the simulation of sodium pool combustion. • A sodium evaporation based model is proposed to model sodium pool evaporation. • The proposed method is validated against sodium pool experiments of Newman and Payne. • The results obtained using the proposed method are in good agreement with the experiments. - Abstract: The risk of sodium-air reaction has received considerable attention after the sodium-fire accident in Monju reactor. The fires resulting from the sodium-air reaction can be detrimental to the safety of a sodium fast reactor. Therefore, predicting the consequences of a sodium fire is important from a safety point of view. A computational method based on CFD is proposed here to simulate sodium pool fire and understand its characteristics. The method solves the Favre-averaged Navier-Stokes equation and uses a non-premixed mixture fraction based combustion model. The mass transfer of sodium vapor from the pool surface to the flame is obtained using a sodium evaporation model. The proposed method is then validated against well-known sodium pool experiments of Newman and Payne. The flame temperature and location predicted by the model are in good agreement with experiments. Furthermore, the trends of the mean burning rate with initial pool temperature and oxygen concentration are captured well. Additionally, parametric studies have been performed to understand the effects of pool diameter and initial air temperature on the mean burning rate. Furthermore, the sodium spray and sodium pool combustion models are combined to simulate simultaneous spray and pool combustion. Simulations were performed to demonstrate that the combined code could be applied to simulate this. Once sufficiently validated, the present code can be used for safety evaluation of a sodium fast reactor

Numerical modeling of sodium fire – Part II: Pool combustion and combined spray and pool combustion

Energy Technology Data Exchange (ETDEWEB)

Sathiah, Pratap, E-mail: pratap.sathiah78@gmail.com [Shell Global Solutions Ltd., Brabazon House, Concord Business Park, Threapwood Road, Manchester M220RR (United Kingdom); Roelofs, Ferry, E-mail: roelofs@nrg.eu [Nuclear Research and Consultancy Group (NRG), Westerduinweg 3, 1755ZG Petten (Netherlands)

2014-10-15

Highlights: • A CFD based method is proposed for the simulation of sodium pool combustion. • A sodium evaporation based model is proposed to model sodium pool evaporation. • The proposed method is validated against sodium pool experiments of Newman and Payne. • The results obtained using the proposed method are in good agreement with the experiments. - Abstract: The risk of sodium-air reaction has received considerable attention after the sodium-fire accident in Monju reactor. The fires resulting from the sodium-air reaction can be detrimental to the safety of a sodium fast reactor. Therefore, predicting the consequences of a sodium fire is important from a safety point of view. A computational method based on CFD is proposed here to simulate sodium pool fire and understand its characteristics. The method solves the Favre-averaged Navier-Stokes equation and uses a non-premixed mixture fraction based combustion model. The mass transfer of sodium vapor from the pool surface to the flame is obtained using a sodium evaporation model. The proposed method is then validated against well-known sodium pool experiments of Newman and Payne. The flame temperature and location predicted by the model are in good agreement with experiments. Furthermore, the trends of the mean burning rate with initial pool temperature and oxygen concentration are captured well. Additionally, parametric studies have been performed to understand the effects of pool diameter and initial air temperature on the mean burning rate. Furthermore, the sodium spray and sodium pool combustion models are combined to simulate simultaneous spray and pool combustion. Simulations were performed to demonstrate that the combined code could be applied to simulate this. Once sufficiently validated, the present code can be used for safety evaluation of a sodium fast reactor.

Flame Retardant and Antimicrobial Jute Textile Using Sodium Metasilicate Nonahydrate

Directory of Open Access Journals (Sweden)

Basak S.

2014-06-01

Full Text Available Flame retardant and antimicrobial functionalities were imparted in jute textile using sodium metasilicate nonahydrate (SMSN, commonly known as “water glass”. Sodium metasilicate nonahydrate (SMSN was applied in jute fabric in different concentration by padding method followed by drying. Flame retardancy of the fabric was evaluated by Limiting Oxygen Index (LOI and burning behaviour under vertical flammability tester including the char length. Burning rate was found to decrease by almost 10 times after an application of 2% SMSN compared to the control sample. Thermogravimetry (TG and differential scanning calorimetry (DSC analysis of both the control and treated jute fabrics were utilized to understand the mechanism of developed flame retardance in jute fabric. It was observed that the SMSN treated samples showed excellent antimicrobial property against both gram positive and gram negative bacteria. Antimicrobial properties of both the control and treated jute fabrics were also measured quantitatively.

Skin resurfacing in a circumferential full thickness burn to the penis: lessons learnt.

Science.gov (United States)

Jabir, Shehab; Frew, Quentin; Thompson, Richard; Dziewulski, Peter

2013-08-13

A circumferential full-thickness burn to the penis is a rarely encountered injury. However, when it does occur, it proves a management challenge to the plastic and burns surgeon in terms of reconstruction. This is due to the need of not only regaining adequate function of the organ, but also because of the need for a pleasing aesthetic outcome. Split-skin grafts have been utilised successfully to resurface full thickness burns of the penis and have given good results. Yet the success of split-skin grafts, especially those applied to an anatomically challenging region of the body such as the penis, depends on a number of carefully thought-out steps. We discuss the case of a circumferential full-thickness burn to the penis which was treated with split-skin grafting and highlight important pitfalls that the plastic and burns surgeon need to be aware of to ensure a successful outcome.

Experience in the field of sodium fire and prevention in Japan

Energy Technology Data Exchange (ETDEWEB)

Tsuzawa, Y [Power Reactor and Nuclear Fuel Development Corp., Akasaka, Minato-ku, Tokyo (Japan)

1979-03-01

The existing facilities of sodium technology development and liquid sodium cooled fast breeder reactors are equipped with fire-extinguishing powder capable of putting out fire by smothering in case of accidental sodium fire induced by the leakage of high temperature sodium from the circulating system. The purpose of this experiment is to obtain quantitatively the relationship between such a fire-extinguishing powder needed and sodium temperature and its depth. The fourteen different experiments were performed using Na{sub 2}CO{sub 3} type and NaCl type powder both of which are authorized as fire-extinguishing agent under the present governmental regulation, and the sodium (25 cm deep in the test container) being heated up to 300 deg. C and 600 deg. C, and burned. The present experiment has shown the prospective that the amount of fire extinguishing powder of 45 kg/m{sup 2} at maximum is sufficient to control the accidental sodium fire under the foreseeable circumstances. (author)

Experience in the field of sodium fire and prevention in Japan

International Nuclear Information System (INIS)

Tsuzawa, Y.

1979-01-01

The existing facilities of sodium technology development and liquid sodium cooled fast breeder reactors are equipped with fire-extinguishing powder capable of putting out fire by smothering in case of accidental sodium fire induced by the leakage of high temperature sodium from the circulating system. The purpose of this experiment is to obtain quantitatively the relationship between such a fire-extinguishing powder needed and sodium temperature and its depth. The fourteen different experiments were performed using Na 2 CO 3 type and NaCl type powder both of which are authorized as fire-extinguishing agent under the present governmental regulation, and the sodium (25 cm deep in the test container) being heated up to 300 deg. C and 600 deg. C, and burned. The present experiment has shown the prospective that the amount of fire extinguishing powder of 45 kg/m 2 at maximum is sufficient to control the accidental sodium fire under the foreseeable circumstances. (author)

Sodium spray and jet fire model development within the CONTAIN-LMR code

International Nuclear Information System (INIS)

Scholtyssek, W.

1993-01-01

An assessment was made of the sodium spray fire model implemented in the CONTAIN code. The original droplet burn model, which was based on the NACOM code, was improved in several aspects, especially concerning evaluation of the droplet burning rate, reaction chemistry and heat balance, spray geometry and droplet motion, and consistency with CONTAIN standards of gas property evaluation. An additional droplet burning model based on a proposal by Krolikowski was made available to include the effect of the chemical equilibrium conditions at the flame temperature. The models were validated against single-droplet burn experiments as well as spray and jet fire experiments. Reasonable agreement was found between the two burn models and experimental data. When the gas temperature in the burning compartment reaches high values, the Krolikowski model seems to be preferable. Critical parameters for spray fire evaluation were found to be the spray characterization, especially the droplet size, which largely determines the burning efficiency, and heat transfer conditions at the interface between the atmosphere and structures, which controls the thermal hydraulic behavior in the burn compartment

Perbandingan Penyembuhan Luka Bakar Derajat Dua antara Rebusan Daun Sirih dan Moist Exposed Burn Ointment

Directory of Open Access Journals (Sweden)

Ihsan

2012-06-01

Full Text Available The use of topical agent is one of the main strategies in management of burn injury. At Dr. Hasan Sadikin Hospital, moist exposed burn ointment (MEBO is the first line topical agent for treating burn injury, not all places in Indonesia able to use it. Piper betle is one of the traditional agent to treat wound including that caused burn injury. Our experimental study was to compare the second grade burn injury healing process by using Wistar sp. for boiled piper betle leaves, MEBO and as control physiologic sodium chloride for fourteen days (August 25th–September 8th 2009 at Animal Pharmacology Laboratory of Faculty of Medicine Padjadjaran University. The variables which measured were diameter of injury, pus development, evidence of serous and erythematous skin, at 4th, 7th and 14th day of studied. Histopathologic examination was conducted at day 14 to determine the amount of fibroblast, collagen and epithelial. The results according to the measurement of diameter (piper betle leaves group 17.4 mm was smaller than other groups (p<0.001. In pus development control group was higher than other groups (p=0.043. In pathological findings, the control group was at inflammation phase, while in boiled piper betle leaves group was at proliferation phase and in MEBO group at remodeling phase (with epithel score 1.9 which higher than other groups (p<0.001. In conclusions, application of boiled piper betle leaves in treating second degree burn injury gives a better result than physiologic sodium chloride, although MEBO is better for second degree burn injury healing process.

Production of sodium bicarbonate from a basic process stream

NARCIS (Netherlands)

Witkamp, G.J.; Van Spronsen, J.; Hasselaar, M.

2012-01-01

The present invention is in the area of the treatment of a gas flow containing carbon dioxide obtained from burning at least one organic waste or feed stream, on the one hand to produce sodium bicarbonate and optionally remove and/or recover molybdenum compounds and/or other impurities from the said

Enhancing TRU burning and Am transmutation in Advanced Recycling Reactor

International Nuclear Information System (INIS)

Ikeda, Kazumi; Kochendarfer, Richard A.; Moriwaki, Hiroyuki; Kunishima, Shigeru

2011-01-01

Research highlights: → This ARR is an oxide fueled sodium cooled reactor based on innovative technologies to destruct TRU. → TRU burning core is designed to burn TRU at 28 kg/TW th h, adding moderator pins of B 4 C (Enriched B-11). → Am transmutation core can transmute Am at 34 kg/TW th h, adding uranium free AmN blanket to TRU burning core. → The TRU burning core improves TRU burning by 40-50% than the previous core. → The Am transmutation core can transmute Am effectively, keeping the void reactivity acceptable. - Abstract: This paper presents about conceptual designs of Advanced Recycling Reactor (ARR) focusing on enhancement in transuranics (TRU) burning and americium (Am) transmutation. The design has been conducted in the context of the Global Nuclear Energy Partnership (GNEP) seeking to close nuclear fuel cycle in ways that reduce proliferation risks, reduce the nuclear waste in the US and further improve global energy security. This study strives to enhance the TRU burning and the Am transmutation, assuming the development of related technologies in this study, while the ARR based on mature technologies was designed in the previous study. It has followed that the provided TRU burning core is designed to burn TRU at 28 kg/TW th h, by adding moderator pins of B 4 C (Enriched B-11) and the Am transmutation core will be able to transmute Am at 34 kg/TW th h, by locating Am blanket of AmN around the TRU burning core. It indicates that these concepts improve TRU burning by 40-50% than the previous core and can transmute Am effectively, keeping the void reactivity acceptable.

MSFR TRU-burning potential and comparison with an SFR

Energy Technology Data Exchange (ETDEWEB)

Fiorina, C.; Cammi, A. [Politecnico di Milano: Via La Masa 34, 20136 Milan (Italy); Franceschini, F. [Westinghouse Electric Company LL: 1000 Westinghouse Dr., Cranberry Township, PA 16066 (United States); Krepel, J. [Paul Scherrer Institut - PSI WEST, 5234 Villigen (Switzerland)

2013-07-01

The objective of this work is to evaluate the Molten Salt Fast Reactor (MSFR) potential benefits in terms of transuranics (TRU) burning through a comparative analysis with a sodium-cooled FR. The comparison is based on TRU- and MA-burning rates, as well as on the in-core evolution of radiotoxicity and decay heat. Solubility issues limit the TRU-burning rate to 1/3 that achievable in traditional low-CR FRs (low-Conversion-Ratio Fast Reactors). The softer spectrum also determines notable radiotoxicity and decay heat of the equilibrium actinide inventory. On the other hand, the liquid fuel suggests the possibility of using a Pu-free feed composed only of Th and MA (Minor Actinides), thus maximizing the MA burning rate. This is generally not possible in traditional low-CR FRs due to safety deterioration and decay heat of reprocessed fuel. In addition, the high specific power and the lack of out-of-core cooling times foster a quick transition toward equilibrium, which improves the MSFR capability to burn an initial fissile loading, and makes the MSFR a promising system for a quick (i.e., in a reactor lifetime) transition from the current U-based fuel cycle to a novel closed Th cycle. (authors)

An unsuspected cause of meal-time morbidity: instant noodle scald burns.

Science.gov (United States)

Koltz, Peter F; Wasicek, Philip; Mays, Chester; Bell, Derek E

2013-01-01

Observational analysis revealed a concerning frequency of scald burns secondary to instant noodles. A literature review reveals studies with small sample sizes of pediatric populations and analysis of container engineering. The adult cohort, treatments, and short-term outcomes have been neglected. Considering these deficiencies, we reviewed our institution's experience with burns secondary to instant noodles. Patient encounters due to instant noodle burns from January 1, 2007, through May 15, 2011, were reviewed. Demographics, burn characteristics, treatment, length of stay, number of operative interventions, and complications were analyzed. Eight hundred fifty-two patients were seen (460 were admitted) for scald burns of all pathogenesis. Of these, 121 (14%) were seen for burns secondary to noodles (63 men and 58 women). Of these, 48 were older than age 4 (group 1), and 73 were younger than age 4 (group 2). TBSA was 2.34 in group 1 and 1.64 in group 2 (P = .04). The most commonly burned areas in group 1 were extremities (n = 43) and in group 2 were chest (n = 32) and extremities (n = 31). Seven patients in group 1 and two patients in group 2 required operative intervention. Length of stay in groups 1 and 2 were 3.5 and 6 days, respectively. Noodle scald burns cause morbidity at all ages. Pediatric burns due to noodles are frequently managed conservatively but more often necessitate inpatient treatment. The nonpediatric population has larger TBSA and requires more frequent operative intervention. The morbidity of noodle burns is significant. Increased public education and container re-engineering is warranted.

Delayed gamma power measurement for sodium-cooled fast reactors

Energy Technology Data Exchange (ETDEWEB)

Coulon, R., E-mail: romain.coulon@cea.f [CEA, LIST, Laboratoire Capteurs et Architectures Electroniques, F-91191 Gif-sur-Yvette (France); Normand, S., E-mail: stephane.normand@cea.f [CEA, LIST, Laboratoire Capteurs et Architectures Electroniques, F-91191 Gif-sur-Yvette (France); Ban, G., E-mail: ban@lpccaen.in2p3.f [ENSICAEN, 6 Boulevard Marechal Juin, F-14050 Caen Cedex 4 (France); Barat, E.; Montagu, T.; Dautremer, T. [CEA, LIST, Laboratoire Modelisation Simulation et Systemes, F-91191 Gif-sur-Yvette (France); Brau, H.-P. [ICSM, Centre de Marcoule, BP 17171 F-30207 Bagnols sur Ceze (France); Dumarcher, V. [AREVA NP, SET, F-84500 Bollene (France); Michel, M.; Barbot, L.; Domenech, T.; Boudergui, K.; Bourbotte, J.-M. [CEA, LIST, Laboratoire Capteurs et Architectures Electroniques, F-91191 Gif-sur-Yvette (France); Jousset, P. [CEA, LIST, Departement des Capteurs, du Signal et de l' Information, F-91191 Gif-sur-Yvette (France); Barouch, G.; Ravaux, S.; Carrel, F. [CEA, LIST, Laboratoire Modelisation Simulation et Systemes, F-91191 Gif-sur-Yvette (France); Saurel, N. [CEA, DAM, Laboratoire Mesure de Dechets et Expertise, F-21120 Is-sur-Tille (France); Frelin-Labalme, A.-M.; Hamrita, H. [CEA, LIST, Laboratoire Capteurs et Architectures Electroniques, F-91191 Gif-sur-Yvette (France)

2011-01-15

Graphical abstract: Display Omitted Research highlights: {sup 20}F and {sup 23}Ne tagging agents are produced by fast neutron flux. {sup 20}F signal has been measured at the SFR Phenix prototype. A random error of only 3% for an integration time of 2 s could be achieved. {sup 20}F and {sup 23}Ne power measurement has a reduced temperature influence. Burn-up impact could be limited by simultaneous {sup 20}F and {sup 23}Ne measurement. - Abstract: Previous works on pressurized water reactors show that the nitrogen 16 activation product can be used to measure thermal power. Power monitoring using a more stable indicator than ex-core neutron measurements is required for operational sodium-cooled fast reactors, in order to improve their economic efficiency at the nominal operating point. The fluorine 20 and neon 23 produced by (n,{alpha}) and (n,p) capture in the sodium coolant have this type of convenient characteristic, suitable for power measurements with low build-up effects and a potentially limited temperature, flow rate, burn-up and breeding dependence. This method was tested for the first time during the final tests program of the French Phenix sodium-cooled fast reactor at CEA Marcoule, using the ADONIS gamma pulse analyzer. Despite a non-optimal experimental configuration for this application, the delayed gamma power measurement was pre-validated, and found to provide promising results.

Acoustic and turbulent agglomeration of sodium aerosols. Progress report, January 1, 1977--December 31, 1977

International Nuclear Information System (INIS)

Hinds, W.C.

1977-09-01

Freshly formed and aged sodium aerosols generated by burning metallic sodium in air were decontaminated in wet cell washers of experimental design. Two wetted cells in series packed with curly glass fibers 35 μm in diameter gave removal efficiencies in excess of 90%. More efficient cell packings and a larger number of cells in series can be used to raise collection efficiency above 99%

Spontaneous neutrophil migration patterns during sepsis after major burns.

Science.gov (United States)

Jones, Caroline N; Moore, Molly; Dimisko, Laurie; Alexander, Andrew; Ibrahim, Amir; Hassell, Bryan A; Warren, H Shaw; Tompkins, Ronald G; Fagan, Shawn P; Irimia, Daniel

2014-01-01

Finely tuned to respond quickly to infections, neutrophils have amazing abilities to migrate fast and efficiently towards sites of infection and inflammation. Although neutrophils ability to migrate is perturbed in patients after major burns, no correlations have yet been demonstrated between altered migration and higher rate of infections and sepsis in these patients when compared to healthy individuals. To probe if such correlations exist, we designed microfluidic devices to quantify the neutrophil migration phenotype with high precision. Inside these devices, moving neutrophils are confined in channels smaller than the neutrophils and forced to make directional decisions at bifurcations and around posts. We employed these devices to quantify neutrophil migration across 18 independent parameters in 74 blood samples from 13 patients with major burns and 3 healthy subjects. Blinded, retrospective analysis of clinical data and neutrophil migration parameters revealed that neutrophils isolated from blood samples collected during sepsis migrate spontaneously inside the microfluidic channels. The spontaneous neutrophil migration is a unique phenotype, typical for patients with major burns during sepsis and often observed one or two days before the diagnosis of sepsis is confirmed. The spontaneous neutrophil migration phenotype is rare in patients with major burns in the absence of sepsis, and is not encountered in healthy individuals. Our findings warrant further studies of neutrophils and their utility for early diagnosing and monitoring sepsis in patients after major burns.

Improving burn care and preventing burns by establishing a burn database in Ukraine.

Science.gov (United States)

Fuzaylov, Gennadiy; Murthy, Sushila; Dunaev, Alexander; Savchyn, Vasyl; Knittel, Justin; Zabolotina, Olga; Dylewski, Maggie L; Driscoll, Daniel N

2014-08-01

Burns are a challenge for trauma care and a contribution to the surgical burden. The former Soviet republic of Ukraine has a foundation for burn care; however data concerning burns in Ukraine has historically been scant. The objective of this paper was to compare a new burn database to identify problems and implement improvements in burn care and prevention in this country. Retrospective analyses of demographic and clinical data of burn patients including Tukey's post hoc test, analysis of variance, and chi square analyses, and Fisher's exact test were used. Data were compared to the American Burn Association (ABA) burn repository. This study included 1752 thermally injured patients treated in 20 hospitals including Specialized Burn Unit in Municipal Hospital #8 Lviv, Lviv province in Ukraine. Scald burns were the primary etiology of burns injuries (70%) and burns were more common among children less than five years of age (34%). Length of stay, mechanical ventilation use, infection rates, and morbidity increased with greater burn size. Mortality was significantly related to burn size, inhalation injury, age, and length of stay. Wound infections were associated with burn size and older age. Compared to ABA data, Ukrainian patients had double the length of stay and a higher rate of wound infections (16% vs. 2.4%). We created one of the first burn databases from a region of the former Soviet Union in an effort to bring attention to burn injury and improve burn care. Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

Design of the US-CRBRP sodium/water reaction pressure relief system

International Nuclear Information System (INIS)

Kruger, G.B.; Murdock, T.B.; Rodwell, E.; Sane, J.O.

1976-01-01

Protection against intermediate sodium system overpressure from the sodium/water reaction associated with large leaks within the CRBRP Steam Generators is provided by the sodium/water reaction pressure relief system (SWRPRS). This system consists of rupture disks connected to the intermediate sodium piping adjacent to the inlet to the superheater and outlet from the evaporator modules. The rupture discs relieve into piping that leads to reaction produce separator tanks, which in turn are vented to a centrifugal separator and flare stack arranged to burn hydrogen gas exhausting into the atmosphere. Analyses have been conducted using the TRANSWRAP Computer Code to predict the system pressures and flow rates during the large leak event. Experimental tests to be conducted in the large leak test rig (LLTR) will be used to confirm the analysis techniques used in the design

Prevention of burn-on defect on surface of hydroturbine blade casting of ultra-low-carbon refining stainless steel

Directory of Open Access Journals (Sweden)

Li Ling

2008-08-01

Full Text Available The burn-on sand is common surface defect encountered in CO2-cured silicate-bonded sand casting of hydroturbine blade of ultra-low-carbon martensitic stainless steel, its feature, causes and prevention measures are presented in this paper. Experiments showed that the burn-on defect is caused by oxidization of chromium in the molten steel at high temperature and can be effectively eliminated by using chromium-corundum coating.

Burned-Out Testicular Tumor: A Case Report

Directory of Open Access Journals (Sweden)

N. Balalaa

2011-01-01

Full Text Available Germ cell tumors constitute the majority of all testicular tumors, which are relatively rare overall and are mainly encountered in young adults and teenagers. The term ‘burned-out’ germ cell tumor refers to the presence of a metastatic germ cell tumor with histological regression of the primary testicular lesion. Clinical examination of the testes and scrotal sonography is pivotal in the initial diagnosis of such neoplasms. We present a case of a 31-year-old male with a retroperitoneal mass and no palpable lesion on testicular examination.

A novel model approach for esophageal burns in rats: A comparison of three methods.

Science.gov (United States)

Kalkan, Yildiray; Tumkaya, Levent; Akdogan, Remzi Adnan; Yucel, Ahmet Fikret; Tomak, Yakup; Sehitoglu, İbrahim; Pergel, Ahmet; Kurt, Aysel

2015-07-01

Corrosive esophageal injury causes serious clinical problems. We aimed to create a new experimental esophageal burn model using a single catheter without a surgical procedure. We conducted the study with two groups of 12 male rats that fasted for 12 h before application. A modified Foley balloon catheter was inserted into the esophageal lumen. The control group was given 0.9% sodium chloride, while the experimental group was given 37.5% sodium hydroxide with the other part of the catheter. After 60s, esophagus was washed with distilled water. The killed rats were examined using histopathological methods after 28 days. In comparison with the histopathological changes experienced by the study groups, the control groups were observed to have no pathological changes. Basal cell degeneration, dermal edema, and a slight increase in the keratin layer and collagen density of submucosa due to stenosis were all observed in the group subjected to esophageal corrosion. A new burn model can thus, we believe, be created without the involvement of invasive laparoscopic surgery and general anesthesia. The burn in our experiment was formed in both the distal and proximal esophagus, as in other models; it can also be formed optionally in the entire esophagus. © The Author(s) 2013.

Design comparisons of TRU burner cores with similar sodium void worth

International Nuclear Information System (INIS)

Sang Ji, Kim; Young Il, Kim; Young Jin, Kim; Nam Zin, Cho

2001-01-01

This study summarizes the neutronic performance and fuel cycle behavior of five geometrically-different transuranic (TRU) burner cores with similar low sodium void reactivity. The conceptual cores encompass core geometries for annular, two-region homogeneous, dual pin type, pan-shaped and H-shaped cores. They have been designed with the same assembly specifications and managed to have similar end-of-cycle sodium void reactivities and beginning-of-cycle peak power densities through the changes in the core size and configuration. The requirement of low sodium void reactivity is shown to lead each design concept to characteristic neutronics performance and fuel cycle behavior. The H-/pan-shaped cores allow the core compaction as well as higher rate of TRU burning. (author)

Atmospheric diffusion and fallout and alkaline materials produced by sodium fires

International Nuclear Information System (INIS)

Benfenati, I.

1982-01-01

The present works deals with a theoretic approach of the diffusion in air of colloidal Na 2 O coming out of sodium fires, consequent to sodium losses from the cooling circuit of a fast breeder reactor, in case of accident. The theoretical pattern has subsequently been applied to a numerical assessment of the Na 2 O concentration in air and on the ground (due to fallout), either inside or outside the sodium hall of the Cpv-1 facility at the Brasimone site. The assessment refers to the maximum credible accident 'pool burning', in the most unfavourable meteorological conditions. Protectionistic recomendations are given, and emergency procedures are described, in that concerns boot people professionally employed within the reactor site and the external population

Fuel and fission product release from sodium

International Nuclear Information System (INIS)

Sauter, H.

1992-01-01

The NALA program at Kernforschungszentrum Karlsruhe is concerned with the release of fuel and fission products from hot or boiling sodium pools (radiological secondary source term) in a liquid-metal fast breeder reactor accident scenario with tank failure. The main concern is to determine retention factors (RF), to uncover the most essential parameters that influence the RF values, and to describe the way they do it. In the framework of the last NALA series, NALA IIIc, the influence of sodium-concrete interaction was investigated, partly with subsequent sodium burning. In our experiments, ∼3 kg of sodium and added pieces of concrete reaching from 4 to 40 g was used. The composition of the concrete was suitable for shielding and construction as used in the SNR-300 reactor. Fuel was simulated by 20-μm particles of depleted UO 2 , and CeO 2 , NaI, and TeO 2 were used as fission products. Most experiments were performed in an inert argon gas atmosphere with monitored hydrogen development. In some cases, the preheated pool was allowed to come into contact with ambient air, which caused an ordinary sodium fire. For the latter case, we used the 220-m 3 FAUNA vessel as an outer containment and collected the fire aerosols by a trap and subsequent filters for analysis

Organised Cultural Encounters

DEFF Research Database (Denmark)

Christiansen, Lene Bull; Galal, Lise Paulsen; Hvenegård-Lassen, Kirsten

2017-01-01

The article introduces the special issue by presenting the concept of organised cultural encounters that are encounters organised to manage and/or transform problems perceived to originate in or include cultural differences. Inspired by Pratt’s conceptualisation of the contact zone, a critical...... perspective on the particular historical and spatial context of any encounter and how this context frames and mediates what takes place during an encounter is applied. While the articles of the issue present different varieties of organised cultural encounters, it is argued that they are not only of the same...

Assessment of Knowledge, Attitude and Practice of Solid Waste Open Burning in Terengganu, Malaysia

Directory of Open Access Journals (Sweden)

Mariani Ariffin

2017-07-01

Full Text Available With more than 40 percent of the world’s rubbish is burned, open burning is a significant source of atmospheric pollution globally and remains one of the main environmental issues and health concerns for many developing nations. Despite having stringent criminal penalties for illegal open burning, Malaysia encounters increasing trend in open burning incidents. A better understanding of the knowledge, attitudinal, and perception towards open burning would inform more effective intervention efforts towards changing this trend. A questionnaire survey to assess knowledge, attitude and practice of public was conducted in Kuala Terengganu. A total of 384 respondents from various demographic backgrounds participated in the survey. Descriptive analysis was used to analyse the respondents’ socio-demographic profiles. Pearson correlation was used to uncover the relationship between knowledge, attitude and practice among the respondents. Results showed that the respondents had good knowledge on open burning and showed positive attitude towards protecting the environment from the problem. However, they displayed lack of practice to tackle the problem in real life. The study also found a weak relationship between knowledge with attitude and practice on open burning. Policy-makers should, therefore, devise intervention programmes that can encourage higher practice rather than merely focusing on raising awareness.

Cultural geography. Different encounters, encountering difference

OpenAIRE

Longhurst, Robyn

2007-01-01

In the first half of this paper it is argued that cultural geography is a dynamic and diverse field that extends well beyond a single branch of human geography. The boundaries between it and other sub-disciplines are often blurred. People have «different» encounters with cultural geography depending on their sub-disciplinary convergences. People also have different encounters with cultural geography depending on where they live and work. «Place matters» in the construction, production and rep...

Characteristic and composition of smokes in sodium fires

International Nuclear Information System (INIS)

Goncalves, A.C.; Torres, A.R.; Brito Aghina, L.O. de; Messere e Castro, P.

1986-01-01

The formation ratios of chemical principal compounds appear in smokes of fires up to 50 Kg of sodium in installations for fast reactor researches, were measured for a simulation in a scale of 1:1000. Relations of hydroxide concentrations, carbonate and bicarbonate appear in smokes retained in counter-current washing tower and in dry filters are presented. It is still presented the variation of the temperature profile and composition of burning wastes. (Author) [pt

Research on mouse model of grade II corneal alkali burn

Directory of Open Access Journals (Sweden)

Jun-Qiang Bai

2016-04-01

Full Text Available AIM: To choose appropriate concentration of sodium hydroxide (NaOH solution to establish a stable and consistent corneal alkali burn mouse model in grade II. METHODS: The mice (n=60 were randomly divided into four groups and 15 mice each group. Corneal alkali burns were induced by placing circle filter paper soaked with NaOH solutions on the right central cornea for 30s. The concentrations of NaOH solutions of groups A, B, C, and D were 0.1 mol/L, 0.15 mol/L , 0.2 mol/L, and 1.0 mol/L respectively. Then these corneas were irrigated with 20 mL physiological saline (0.9% NaCl. On day 7 postburn, slit lamp microscope was used to observe corneal opacity, corneal epithelial sodium fluorescein staining positive rate, incidence of corneal ulcer and corneal neovascularization, meanwhile pictures of the anterior eyes were taken. Cirrus spectral domain optical coherence tomography was used to scan cornea to observe corneal epithelial defect and corneal ulcer. RESULTS: Corneal opacity scores ( were not significantly different between the group A and group B (P=0.097. Incidence of corneal ulcer in group B was significantly higher than that in group A (P=0.035. Incidence of corneal ulcer and perforation rate in group B was lower than that in group C. Group C and D had corneal neovascularization, and incidence of corneal neovascularization in group D was significantly higher than that in group C (P=0.000. CONCLUSION: Using 0.15 mol/L NaOH can establish grade II mouse model of corneal alkali burns.

Mobile encounters

DEFF Research Database (Denmark)

Koefoed, Lasse Martin; Christensen, Mathilde Dissing; Simonsen, Kirsten

2017-01-01

The paper explores modes of encounters in the everyday practice of bus travel. Particularly, it addresses cross-cultural encounters located in the tension between familiarity and difference, between inclusion and exclusion. The paper is located in contemporary thoughts, approaching public transport...... not only as a moving device but also as a social arena. Furthermore, the bus is simultaneously perceived as a public space, at once composite, contradictory and heterogeneous, and as a meeting place involving ‘Throwntogetherness’. The encounters analysed are bodily, emotional charged and outspoken meetings...

Cold trap dismantling and sodium removal at a fast breeder reactor

Energy Technology Data Exchange (ETDEWEB)

Graf, Anja; Petrick, Holger; Stutz, Uwe [WAK GmbH, Eggenstein-Leopoldshafen (Germany). Hauptabt. Dekontaminationsbetriebe Rueckbau Kompakte Natriumgekuehlte Kernreaktoranlage (KNK); Hosking, Paul [Nuclear Decommissioning Services Limited (NDSL), Sutherland, Dornoch (United Kingdom)

2013-11-15

The first German prototype Fast Breeder Nuclear Reactor (KNK) is currently being dismantled after being the only operating Fast Breeder-type reactor in Germany. As this reactor type used sodium as a coolant in its primary and secondary circuit, 7 cold traps containing various amounts of partially activated sodium needed to be disposed of as part of the dismantling. The resulting combined difficulties of radioactive contamination and high chemical reactivity were handled by treating the cold traps differently depending on their size and the amount of sodium contained inside. Six small cold traps were processed on-site by cutting them up into small parts using a band saw under a protective atmosphere. The sodium was then converted to sodium hydroxide by using water. The remaining large cold trap could not be handled in the same way due to its dimensions (2.9 m x 1.1 m) and the declared amount of sodium inside (1,700 kg). It was therefore manually dismantled inside a large box filled with a protective atmosphere, while the resulting pieces were packaged for later burning in a special facility. The experiences gained by KNK during this process may be advantageous for future dismantling projects in similar sodium-cooled reactors worldwide. (orig.)

Impacts of burnup-dependent swelling of metallic fuel on the performance of a compact breed-and-burn fast reactor

Energy Technology Data Exchange (ETDEWEB)

Hartanto, Donny; Heo, Woong; Kim, Chi Hyung; Kim, Yong Hee [Dept. of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon (Korea, Republic of)

2016-04-15

The U-Zr or U-TRU-Zr cylindrical metallic fuel slug used in fast reactors is known to swell significantly and to grow during irradiation. In neutronics simulations of metallic-fueled fast reactors, it is assumed that the slug has swollen and contacted cladding, and the bonding sodium has been removed from the fuel region. In this research, a realistic burnup-dependent fuel-swelling simulation was performed using Monte Carlo code McCARD for a single-batch compact sodium-cooled breed-and-burn reactor by considering the fuel-swelling behavior reported from the irradiation test results in EBR-II. The impacts of the realistic burnup-dependent fuel swelling are identified in terms of the reactor neutronics performance, such as core lifetime, conversion ratio, axial power distribution, and local burnup distributions. It was found that axial fuel growth significantly deteriorated the neutron economy of a breed-and-burn reactor and consequently impaired its neutronics performance. The bonding sodium also impaired neutron economy, because it stayed longer in the blanket region until the fuel slug reached 2% burnup.

Making of a burn unit: SOA burn center

Directory of Open Access Journals (Sweden)

Jayant Kumar Dash

2016-01-01

Full Text Available Each year in India, burn injuries account for more than 6 million hospital emergency department visits; of which many require hospitalization and are referred to specialized burn centers. There are few burn surgeons and very few burn centers in India. In our state, Odisha, there are only two burn centers to cater to more than 5000 burn victims per year. This article is an attempt to share the knowledge that I acquired while setting up a new burn unit in a private medical college of Odisha.

[Surgical treatment of burns : Special aspects of pediatric burns].

Science.gov (United States)

Bührer, G; Beier, J P; Horch, R E; Arkudas, A

2017-05-01

Treatment of pediatric burn patients is very important because of the sheer frequency of burn wounds and the possible long-term ramifications. Extensive burns need special care and are treated in specialized burn centers. The goal of this work is to present current standards in burn therapy and important innovations in the treatment of burns in children so that the common and small area burn wounds and scalds in pediatric patients in day-to-day dermatological practice can be adequately treated. Analysis of current literature, discussion of reviews, incorporation of current guidelines. Burns in pediatric patients are common. Improvement of survival can be achieved by treatment in burn centers. The assessment of burn depth and area is an important factor for proper treatment. We give an overview for outpatient treatment of partial thickness burns. New methods may result in better long-term outcome. Adequate treatment of burn injuries considering current literature and guidelines improves patient outcome. Rational implementation of new methods is recommended.

The liquid metal embrittlement of iron and ferritic steels in sodium

International Nuclear Information System (INIS)

Hilditch, J.P.; Hurley, J.R.; Tice, D.R.; Skeldon, P.

1995-01-01

The liquid metal embrittlement of iron and A508 III, 21/4Cr-1Mo and 15Mo3 steels in sodium at 200-400 o C has been studied, using dynamic straining at 10 -6 s -1 , in order to investigate the roles of microstructure and composition. The steels comprised bainitic, martensitic, tempered martensitic and ferritic/pearlitic microstructures. All materials were embrittled by sodium, the embrittlement being associated generally with quasicleavage on fracture surfaces. Intergranular cracking was also found with martensitic and ferritic/pearlitic microstructures. The susceptibility to embrittlement was greater in higher strength materials and at higher temperatures. The embrittlement was similar to that encountered previously in 9Cr steel, which depends upon the presence of non-metallic impurities in the sodium. (author)

Operational techniques employed for the liquid sodium source term control loops

International Nuclear Information System (INIS)

Chulos, L.E.

1976-01-01

Four Source Term Control Loops (STCLs) have been designed, constructed, and placed into operation at the Hanford Engineering Development Laboratory (HEDL) as part of the Radioactivity Control Technology program. The data obtained are used to determine the corrosion and deposition of LMFBR materials, including corrosion product radionuclides, in a non-isothermal flowing sodium system. The paper discusses operation of the STCL Facilities and, in particular, the methods used for controlling the oxygen content of the liquid sodium. These methods include cold trapping techniques, hot trapping, seeding the cold traps with sodium oxide, and precipitating the oxygen in the cold trap in a controlled manner. Operational problems encountered with the STCL Facilities and the techniques for correcting these problems are also discussed

Comparative Analysis of Single and Dual Irradiation Pass of Deep Burn High Temperature Reactor Scenario

International Nuclear Information System (INIS)

Jeong, Chang Joon; Jo, Chang Keun; Noh, Jae Man

2012-01-01

A concept of a deep-burn (DB) of trans uranic (TRU) elements in a high temperature reactor (HTR) has been proposed and studied with a single irradiation pass. However, there is still a significant amount of TRU after burn in an HTR. Therefore, it is necessary to burn more TRU in a fast reactor (FR) with repeated reprocessing such as a pyro-process. In this study, the fuel cycle calculations are performed and the results are compared for a singlepass DB-HHR scenario and a dual-pass sodium-cooled fast reactor (SFR) scenario. For the analysis, front-end and back-end parameters are compared. The calculations were performed by the DANESS (Dynamic Analysis of Nuclear Energy System Strategies), which is an integrated system dynamic fuel cycle analysis code

Development of a MELCOR Sodium Chemistry (NAC) Package - FY17 Progress.

Energy Technology Data Exchange (ETDEWEB)

Louie, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Humphries, Larry L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-02-01

This report describes the status of the development of MELCOR Sodium Chemistry (NAC) package. This development is based on the CONTAIN-LMR sodium physics and chemistry models to be implemented in MELCOR. In the past three years, the sodium equation of state as a working fluid from the nuclear fusion safety research and from the SIMMER code has been implemented into MELCOR. The chemistry models from the CONTAIN-LMR code, such as the spray and pool fire mode ls, have also been implemented into MELCOR. This report describes the implemented models and the issues encountered. Model descriptions and input descriptions are provided. Development testing of the spray and pool fire models is described, including the code-to-code comparison with CONTAIN-LMR. The report ends with an expected timeline for the remaining models to be implemented, such as the atmosphere chemistry, sodium-concrete interactions, and experimental validation tests .

Global cooperation and conceptual design toward GNEP. Enhanced TRU burning fast reactor

International Nuclear Information System (INIS)

Ikeda, Kazumi; Maddox, James W.; Nakazato, Wataru; Kunishima, Shigeru

2008-01-01

In support of the GNEP (Global Nuclear Energy Partnership) program, AREVA and Mitsubishi Heavy Industries, Ltd. (MHI) seek to develop an ARR (Advanced Recycling Reactor) in concern with a CFTC (Consolidated Fuel Treatment Facility). This report presents the examination of more effective transuranics (TRU) burning core. Therefore some innovative technologies have been examined under the safety requirements; MA bearing fuel with 50% TRU fraction, moderator pin, fuel of high Am fraction, and Am blanket. The function of moderator is to enhance TRU burning capability, while increasing the Doppler effect and reducing the positive sodium void effect. The aim of 50% TRU fraction is to increase TRU burning capability by curbing plutonium production. Both high Am fraction of fuel and Am blanket can promote Am transmutation. According to the detailed calculation of high TRU (MA 15%, Pu 35% average) contained oxide fueled core with moderator pins of 12% arranged driver fuel assemblies, TRU conversion ratio decreases down to 0.33 and TRU burning capability is improved to 67kg/TWeh. Deploying Am blanket which is oxide fuel with Am 50% and U 50%, the total of Am transmutation capability becomes 69 kg/TWeh. (author)

Thinking about the service encounter enhances encounter-related word-of-mouth

DEFF Research Database (Denmark)

Mattsson, Jan; Söderlund, Magnus

) the memorability of the service encounter and (b) the extent to which what had happened had been subject to rehearsal with the purpose of telling others about it. These findings should be seen in relation to the literature’s view that customer satisfaction, not thinking, is a dominant predictor of word-of-mouth......This study examines the impact of thinking about a service encounter, after it has been completed, on telling others about it (i.e., word-of-mouth). The main finding was that encounter-related thinking boosted word-of-mouth. We also found that the think-talk association was mediated by (a....... Our results, however, indicate that satisfaction’s contribution to the variation in talking about the encounter was modest (and customer satisfaction played only a minor role in explaining why an encounter is thought about)....

Development of evaluation methodology to assess the sodium fire suppression performance of leak collection tray

International Nuclear Information System (INIS)

Parida, F.C.; Rao, P.M.; Ramesh, S.S.; Somayajulu, P.A.; Malarvizhi, B.; Kannan, S.E.

2005-01-01

Full text of publication follows: Leakage of hot liquid sodium and its subsequent combustion in the form of a pool cannot be completely ruled out in a Fast breeder Reactor (FBR) plant in spite of provision for adequate safety measures. To protect the plant system from the hazardous effects of flame, heat and smoke, one of the passive protection devices used in FBR plants is the Leak Collection Tray (LCT). The design of LCT is based on immediate channeling of burning liquid sodium on the funnel shaped sloping cover tray (SCT) to the bottom sodium hold-up vessel (SHV) in which self-extinction of the fire occurs due to oxygen starvation. The SCT has one or three drain pipes and air vent pipes depending on the type of design. In each experiment, a known amount ranging from 30 to 40 kg of hot liquid sodium at 550 deg. C was discharged on the LCT in the open air. Continuous on-line monitoring of temperature at strategic locations (∼ 28 points) was carried out. Colour video-graphy was employed for taking motion pictures of various time-dependent events like sodium dumping, appearance of flame and release of smoke through vent pipes. After self-extinction of sodium fire, the LCT was allowed to cool overnight in an argon atmosphere. Solid samples of sodium debris in the SCT and SHV were collected by manual core drilling machine. The samples were subjected to chemical analysis for determination of unburnt and burnt sodium. The sodium debris removed from SCT and SHV were separately weighed. To assess the performance of the LCT, two different geometrical configurations of SCT, one made up of stainless steel an the other of carbon steel, were used. Three broad phenomena are identified as the basis of evaluation methodology. These are (a) thermal transients, i.e. heating and cooling of the bulk sodium in SCT and SHV respectively, (b) post test sodium debris distribution between SCT and SHV as well as (c) sodium combustion and smoke release behaviour. Under each category

Development of evaluation methodology to assess the sodium fire suppression performance of leak collection tray

Energy Technology Data Exchange (ETDEWEB)

Parida, F.C.; Rao, P.M.; Ramesh, S.S.; Somayajulu, P.A.; Malarvizhi, B.; Kannan, S.E. [Engineering Safety Division, Safety Group, Indira Gandhi Centre for Atomic Research, Kalpakkam - 603102, Tamilnadu (India)

2005-07-01

Full text of publication follows: Leakage of hot liquid sodium and its subsequent combustion in the form of a pool cannot be completely ruled out in a Fast breeder Reactor (FBR) plant in spite of provision for adequate safety measures. To protect the plant system from the hazardous effects of flame, heat and smoke, one of the passive protection devices used in FBR plants is the Leak Collection Tray (LCT). The design of LCT is based on immediate channeling of burning liquid sodium on the funnel shaped sloping cover tray (SCT) to the bottom sodium hold-up vessel (SHV) in which self-extinction of the fire occurs due to oxygen starvation. The SCT has one or three drain pipes and air vent pipes depending on the type of design. In each experiment, a known amount ranging from 30 to 40 kg of hot liquid sodium at 550 deg. C was discharged on the LCT in the open air. Continuous on-line monitoring of temperature at strategic locations ({approx} 28 points) was carried out. Colour video-graphy was employed for taking motion pictures of various time-dependent events like sodium dumping, appearance of flame and release of smoke through vent pipes. After self-extinction of sodium fire, the LCT was allowed to cool overnight in an argon atmosphere. Solid samples of sodium debris in the SCT and SHV were collected by manual core drilling machine. The samples were subjected to chemical analysis for determination of unburnt and burnt sodium. The sodium debris removed from SCT and SHV were separately weighed. To assess the performance of the LCT, two different geometrical configurations of SCT, one made up of stainless steel an the other of carbon steel, were used. Three broad phenomena are identified as the basis of evaluation methodology. These are (a) thermal transients, i.e. heating and cooling of the bulk sodium in SCT and SHV respectively, (b) post test sodium debris distribution between SCT and SHV as well as (c) sodium combustion and smoke release behaviour. Under each category

An overview of sodium-fire related studies in the UK

International Nuclear Information System (INIS)

Bilsborough, R.; Capp, P.D.; Newman, R.N.

1979-01-01

In the six years since the last Sodium Fires Specialists Meeting (Hanford, May 1972) the UKAEA and the Construction Companies, now NPC, have concentrated on the commissioning and early operation of the prototype Fast Reactor (PFR) at Dounreay Nuclear Power Development Establishment. Rig support for PFR has continued at Risley Nuclear Power Development Laboratory with effort mainly directed to engineering and heat transfer studies; the fire protection and leak detection systems used have been based on information available in 1972. Over the same period the CEGB have shown an increasing interest in the Liquid Metal Cooled Fast Reactor system with a consequent increase in research work on the subject of sodium fires. The text and appendices of this overview reflect this spread of emphasis. The ignition characteristics, burning rates and smoke release fractions of free ambient pool fires have been studied and this is described. This paper covers the following topics as well: extinguishment of sodium fires; prevention and protection; aerosols, physical chemistry and codes

An overview of sodium-fire related studies in the UK

Energy Technology Data Exchange (ETDEWEB)

Bilsborough, R [NPC, Risley, Warrington, Cheshire (United Kingdom); Capp, P D [UKAEA, Atomic Energy Establishment Winfrith, Winfrith, Dorchester, Dorset (United Kingdom); Newman, R N [CEGB, Berkely Nuclear Laboratories, Berkley, Gloucestershire (United Kingdom)

1979-03-01

In the six years since the last Sodium Fires Specialists Meeting (Hanford, May 1972) the UKAEA and the Construction Companies, now NPC, have concentrated on the commissioning and early operation of the prototype Fast Reactor (PFR) at Dounreay Nuclear Power Development Establishment. Rig support for PFR has continued at Risley Nuclear Power Development Laboratory with effort mainly directed to engineering and heat transfer studies; the fire protection and leak detection systems used have been based on information available in 1972. Over the same period the CEGB have shown an increasing interest in the Liquid Metal Cooled Fast Reactor system with a consequent increase in research work on the subject of sodium fires. The text and appendices of this overview reflect this spread of emphasis. The ignition characteristics, burning rates and smoke release fractions of free ambient pool fires have been studied and this is described. This paper covers the following topics as well: extinguishment of sodium fires; prevention and protection; aerosols, physical chemistry and codes.

Theoretical modelling of the movement of sodium fire fumes in a building

International Nuclear Information System (INIS)

Vaughan, G.J.; Simpson, C.P.; Smith, A.G.

1989-01-01

The important effect that the thermal hydraulic behaviour in a containment can have on the burning rate of a sodium fire is discussed. To explore the nature of the convective motion induced y the fire and how these might be affected by the containment morphology, calculations with a thermal hydraulic code, PHOENICS, were carried out. This code has also been used to investigate the movement of the smoke cloud produced by a fire to support a study of the use of a venting system. Both studies are reported and some conclusions on the role of thermal hydraulic phenomena on sodium fire investigations are made. (author)

Coexistence of Extended Spectrum Beta-Lactamases, AmpC Beta-Lactamases and Metallo-Beta-Lactamases in Acinetobacter baumannii from burns patients: a report from a tertiary care centre of India

OpenAIRE

Gupta, V.; Garg, R.; Garg, S.; Chander, J.; Attri, A.K.

2013-01-01

Multidrug-resistant Acinetobacter baumanii is a major pathogen encountered in pyogenic infections, especially from burns patients in hospital settings. Often there is also coexistence of multiple beta-lactamase enzymes responsible for beta-lactam resistance in a single isolate, which further complicates treatment options. We conducted a study on burn wound pus samples obtained from the burns unit of our hospital. Phenotypic tests were used to determine the Extended Spectrum Beta-Lactamase, Am...

Burning Mouth Syndrome and "Burning Mouth Syndrome".

Science.gov (United States)

Rifkind, Jacob Bernard

2016-03-01

Burning mouth syndrome is distressing to both the patient and practitioner unable to determine the cause of the patient's symptoms. Burning mouth syndrome is a diagnosis of exclusion, which is used only after nutritional deficiencies, mucosal disease, fungal infections, hormonal disturbances and contact stomatitis have been ruled out. This article will explore the many causes and treatment of patients who present with a chief complaint of "my mouth burns," including symptomatic treatment for those with burning mouth syndrome.

To burn or not to burn

International Nuclear Information System (INIS)

Busch, L.

1993-01-01

While taking a match to an oil slick may sound like the making of a chaotic inferno, emergency response specialists say burning may be the most efficient way to remove large oil spills from the ocean's surface. But tests of this technique are being resisted by environmentalists as well as the Environmental Protection Agency (EPA), which has final authority over the matter. The debate over test burning arose most recently in Alaska when a proposal to spill and then ignite 1,000 barrels of crude on the Arctic Ocean this past summer was rejected by the EPA. The EPA didn't object to the technique or to the notion of burning spilled oil. However, it contends that it's not necessary to spill thousands of gallons of oil to conduct tests, and unnecessarily pollute the environment, when plenty of oil is already available from accidental spills. Researchers disagree, claiming they won't be able to use the burning technique on an actual spill until it has been tested in a controlled experiment. Despite such concerns, the Canadian government is going ahead with a test burn off the coast of Newfoundland next year. Faced with a choice of test burning or the kind of shoreline contamination left in the wake of the Exxon Valdez disaster, Environment Canada opts for testing. Learning valuable lessons about rapid oil-spill cleanup is worth the relatively minor risks to the environment that test burning would pose

Novel burn device for rapid, reproducible burn wound generation.

Science.gov (United States)

Kim, J Y; Dunham, D M; Supp, D M; Sen, C K; Powell, H M

2016-03-01

Scarring following full thickness burns leads to significant reductions in range of motion and quality of life for burn patients. To effectively study scar development and the efficacy of anti-scarring treatments in a large animal model (female red Duroc pigs), reproducible, uniform, full-thickness, burn wounds are needed to reduce variability in observed results that occur with burn depth. Prior studies have proposed that initial temperature of the burner, contact time with skin, thermal capacity of burner material, and the amount of pressure applied to the skin need to be strictly controlled to ensure reproducibility. The purpose of this study was to develop a new burner that enables temperature and pressure to be digitally controlled and monitored in real-time throughout burn wound creation and compare it to a standard burn device. A custom burn device was manufactured with an electrically heated burn stylus and a temperature control feedback loop via an electronic microstat. Pressure monitoring was controlled by incorporation of a digital scale into the device, which measured downward force. The standard device was comprised of a heat resistant handle with a long rod connected to the burn stylus, which was heated using a hot plate. To quantify skin surface temperature and internal stylus temperature as a function of contact time, the burners were heated to the target temperature (200±5°C) and pressed into the skin for 40s to create the thermal injuries. Time to reach target temperature and elapsed time between burns were recorded. In addition, each unit was evaluated for reproducibility within and across three independent users by generating burn wounds at contact times spanning from 5 to 40s at a constant pressure and at pressures of 1 or 3lbs with a constant contact time of 40s. Biopsies were collected for histological analysis and burn depth quantification using digital image analysis (ImageJ). The custom burn device maintained both its internal

Experimental study on combustion and suppression characteristics of sodium fire in a columnar flow using extinguishing powder

International Nuclear Information System (INIS)

Huo Yan; Zhang Zhigang; Li Jinke; Liu Zhongkun; Ma Yaolong

2017-01-01

In the operation of the sodium-cooled fast reactor, the leakage and fire accident of liquid sodium is common and it is frequent in sodium-related facilities. This study focuses on the combustion and suppression characteristics of sodium fire in a columnar flow. Liquid sodium (250°C) is injected into a 7.9 m"3 cylindrical chamber at a flow rate of about 1.0 m"3/h to create a columnar sodium fire, and 18.4 kg class D extinguishing powder is sprayed after the liquid sodium injection. The temperature in the chamber space and sodium collection plate and the heat release rate from sodium fire are measured and analyzed. Based on the temperature data the sodium fire under suppression could be divided into four phases of dropping sharply, continuously remaining lower, rising and declining mildly, and depressing. The sodium fire in the space could be suppressed and cooled down if the extinguishing agent could spray in the early period of the liquid sodium injection. The extinguishing agent could suppress the combustion and spreading of liquid sodium dropping on the collection plate, limit the pool combustion area and postpone the commencement of sodium pool burning in spite of its later re-ignition happening. This study promises to evaluate the combustion and suppression characteristics of sodium fire in the sodium-related facilities. (author)

Burns education for non-burn specialist clinicians in Western Australia.

Science.gov (United States)

McWilliams, Tania; Hendricks, Joyce; Twigg, Di; Wood, Fiona

2015-03-01

Burn patients often receive their initial care by non-burn specialist clinicians, with increasingly collaborative burn models of care. The provision of relevant and accessible education for these clinicians is therefore vital for optimal patient care. A two phase design was used. A state-wide survey of multidisciplinary non-burn specialist clinicians throughout Western Australia identified learning needs related to paediatric burn care. A targeted education programme was developed and delivered live via videoconference. Pre-post-test analysis evaluated changes in knowledge as a result of attendance at each education session. Non-burn specialist clinicians identified numerous areas of burn care relevant to their practice. Statistically significant differences between perceived relevance of care and confidence in care provision were reported for aspects of acute burn care. Following attendance at the education sessions, statistically significant increases in knowledge were noted for most areas of acute burn care. Identification of learning needs facilitated the development of a targeted education programme for non-burn specialist clinicians. Increased non-burn specialist clinician knowledge following attendance at most education sessions supports the use of videoconferencing as an acceptable and effective method of delivering burns education in Western Australia. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Is proportion burned severely related to daily area burned?

International Nuclear Information System (INIS)

Birch, Donovan S; Morgan, Penelope; Smith, Alistair M S; Kolden, Crystal A; Hudak, Andrew T

2014-01-01

The ecological effects of forest fires burning with high severity are long-lived and have the greatest impact on vegetation successional trajectories, as compared to low-to-moderate severity fires. The primary drivers of high severity fire are unclear, but it has been hypothesized that wind-driven, large fire-growth days play a significant role, particularly on large fires in forested ecosystems. Here, we examined the relative proportion of classified burn severity for individual daily areas burned that occurred during 42 large forest fires in central Idaho and western Montana from 2005 to 2007 and 2011. Using infrared perimeter data for wildfires with five or more consecutive days of mapped perimeters, we delineated 2697 individual daily areas burned from which we calculated the proportions of each of three burn severity classes (high, moderate, and low) using the differenced normalized burn ratio as mapped for large fires by the Monitoring Trends in Burn Severity project. We found that the proportion of high burn severity was weakly correlated (Kendall τ = 0.299) with size of daily area burned (DAB). Burn severity was highly variable, even for the largest (95th percentile) in DAB, suggesting that other variables than fire extent influence the ecological effects of fires. We suggest that these results do not support the prioritization of large runs during fire rehabilitation efforts, since the underlying assumption in this prioritization is a positive relationship between severity and area burned in a day. (letters)

Encountering Materiality

DEFF Research Database (Denmark)

Svabo, Connie

2016-01-01

DHT researcher Connie Svabo and artist Charlotte Grum did a joint performance presentation titled Becoming Sheep, Becoming Animal at the international conference Encountering Materiality – Transdisciplinary Conversations, held in Geneve, Schwitzerland, June 23-25 2016.......DHT researcher Connie Svabo and artist Charlotte Grum did a joint performance presentation titled Becoming Sheep, Becoming Animal at the international conference Encountering Materiality – Transdisciplinary Conversations, held in Geneve, Schwitzerland, June 23-25 2016....

An experimental study on suspended sodium droplet combustion (3)

International Nuclear Information System (INIS)

Sato, Kenji

2005-03-01

As part of studies for phenomenological investigation of sodium droplet burning behavior, in our previous experimental studies for suspended single sodium droplet, behavior of ignition process and succeeding combustion, ignition delay time, and droplet temperature history had been investigated. In this study, combustion experiments of suspended sodium droplet were performed in upward dry air flow by expanding the range of free-stream velocity U of air flow into 400 cm/s with initial droplet temperature Ti=300, 350, and 400degC and initial droplet diameter 4 mm at first. Then, the combustion experiments were also performed by changing the initial droplet diameter from 2.3 to 4.4 mm with Ti=350 and 400degC and U=100 cm/s. From the experimental results, the effects of free-stream velocity, initial droplet temperature, and initial droplet diameter on the ignition/burning behavior and ignition delay time were examined. The obtained results are as follows: (1) Ignition phenomena of suspended droplet were observed for all examined experimental conditions up to 400 cm/s. The orange emission observed at the moment of ignition occurs simultaneously over whole droplet surface except the top region of it. (2) The feature of the dependence of ignition delay time on the free-stream velocity is independent of the initial droplet temperature. With the increase of the free-stream velocity, up to 300 cm/s the ignition delay time decreases with decreasing dependency, and then the dependency increases more. (3) The ignition delay time increases with the increase of initial droplet diameter. The dependency increases as the initial droplet diameter increases. The ignition delay time extrapolated toward zero diameters from the obtained results becomes to be essentially zero. (author)

An assessment of burn care professionals' attitudes to major burn.

LENUS (Irish Health Repository)

Murphy, A D

2008-06-01

The resuscitation of severe burn remains a controversial area within the burn care profession. There is ongoing debate as to what percentage burn is associated with a sufficient quality of life to support initial resuscitation efforts. We conducted a survey of delegates at the 39th Annual Meeting of the British Burns Association (2005), regarding attitudes towards resuscitation following major burns. Respondents were asked the maximum percentage total body surface area (TBSA) burn beyond which they would not wish to be resuscitated. They were also asked what maximum TBSA they perceived to be commensurate with an acceptable quality of life (QOL). One hundred and forty three of 300 delegates responded to the questionnaire. Thirty three percent of respondents would not wish to be resuscitated with 50-75% TBSA burns or greater. A further 35% would not wish to have life-sustaining intervention with 75-95% TBSA burns or greater. The remaining 32% indicated that they would not want resuscitation with TBSA burns>95%. Regardless of TBSA affected, 16% would not wish resuscitation if they had full thickness facial burns, a further 10% did not want resuscitation if both their hands and faces were affected. Our survey demonstrates the diversity of personal preference amongst burn care professionals. This would suggest that a unifying philosophy regarding the resuscitation of extensive burns will remain elusive.

Air-Freshener Burns: A New Paradigm in Burns Etiology?

OpenAIRE

Sarwar, Umran; Nicolaou, M.; Khan, M. S.; Tiernan, E.

2011-01-01

Objectives: We report a rare case of burns following the use of automated air-fresheners. Methods: We present a case report with a brief overview of the literature relating to burns associated with air-fresheners. The mechanism and treatment of these types of injuries are also described. Results: A 44 year-old female was admitted under the care of the burns team following burns secondary to an exploding air-freshener canister. The patient sustained burns to the face, thorax and arms re...

Air-freshener burns: a new paradigm in burns etiology?

Science.gov (United States)

Sarwar, Umran; Nicolaou, M; Khan, M S; Tiernan, E

2011-10-01

We report a rare case of burns following the use of automated air-fresheners. We present a case report with a brief overview of the literature relating to burns associated with air-fresheners. The mechanism and treatment of these types of injuries are also described. A 44 year-old female was admitted under the care of the burns team following burns secondary to an exploding air-freshener canister. The patient sustained burns to the face, thorax and arms resulting in a seven-day hospital admission. The burns were treated conservatively. To our knowledge this is one of the few documented cases of burns as a result of air-fresheners. As they become more ubiquitous, we anticipate the incidence of such cases to increase. As such, they pose a potential public health concern on a massive scale.

In-situ burning of Orimulsion : small scale burns

International Nuclear Information System (INIS)

Fingas, M.F.

2002-01-01

This study examined the feasibility of burning Orimulsion. In-situ burning has always been a viable method for cleaning oil spills on water because it can effectively reduce the amount of spilled oil and eliminate the need to collect, store, transport and dispose of recovered oil. Orimulsion, however, behaves very differently from conventional oil when it is spilled because of its composition of 70 per cent bitumen in 30 per cent water. In-situ burning of this surfactant-stablized oil-in-water emulsion has never been seriously considered because of the perception that Orimulsion could not be ignited, and if it could, ignition would not be sustained. In this study, burn tests were conducted on 3 scales in a Cleveland Open Cup apparatus of 5 cm, 10 cm and 50 cm diameters. Larger scale burns were conducted in specially built pans. All tests were conducted on salt water which caused the bitumen to separate from the water. The objective was to determine if sufficient vapours could be generated to ignite the Orimulsion. The study also measured if a sustained flame would result in successful combustion. Both objectives were successfully accomplished. Diesel fuel was used to ignite the Orimulsion in the specially designed pan for large scale combustion. Quantitative removal of Orimulsion was achieved in all cases, but in some burns it was necessary to re-ignite the Orimulsion. It was noted that when Orimulsion burns, some trapped water droplets in the bitumen explode with enough force to extinguish a small flame. This did not occur on large-scale burns. It was concluded that the potential for successful in-situ burning increases with size. It was determined that approximately 1 mm in thickness of diesel fuel is needed to ignite a burn. 5 refs., 3 tabs., 4 figs

ASTRID, Generation IV advanced sodium technological reactor for industrial demonstration

International Nuclear Information System (INIS)

Gauche, F.

2013-01-01

ASTRID (Advanced Sodium Technological Reactor for Industrial Demonstration) is an integrated technology demonstrator designed to demonstrate the operability of the innovative choices enabling fast neutron reactor technology to meet the Generation IV criteria. ASTRID is a sodium-cooled fast reactor with an electricity generating power of 600 MWe. In order to meet the generation IV goals, ASTRID will incorporate the following decisive innovations: -) an improved core with a very low, even negative void coefficient; -) the possible installation of additional safety devices in the core. For example, passive anti-reactivity insertion devices are explored; -) more core instrumentation; -) an energy conversion system with modular steam generators, to limit the effects of a possible sodium-water reaction, or sodium-nitrogen exchangers; -) considerable thermal inertia combined with natural convection to deal with decay heat; -)elimination of major sodium fires by bunkerization and/or inert atmosphere in the premises; -) to take into account off-site hazards (earthquake, airplane crash,...) right from the design stage; -) a complete rethink of the reactor architecture in order to limit the risk of proliferation. ASTRID will also include systems for reducing the length of refueling outages and increasing the burn-up and the duration of the cycle. In-service inspection, maintenance and repair are also taken into account right from the start of the project. The ASTRID prototype should be operational by about 2023. (A.C.)

Modeling Fuel Treatment Leverage: Encounter Rates, Risk Reduction, and Suppression Cost Impacts

Directory of Open Access Journals (Sweden)

Matthew P. Thompson

2017-11-01

Full Text Available The primary theme of this study is the cost-effectiveness of fuel treatments at multiple scales of investment. We focused on the nexus of fuel management and suppression response planning, designing spatial fuel treatment strategies to incorporate landscape features that provide control opportunities that are relevant to fire operations. Our analysis explored the frequency and magnitude of fire-treatment encounters, which are critical determinants of treatment efficacy. Additionally, we examined avoided area burned, avoided suppression costs, and avoided damages, and combined all three under the umbrella of leverage to explore multiple dimensions with which to characterize return on investment. We chose the Sierra National Forest, California, USA, as our study site, due to previous work providing relevant data and analytical products, and because it has the potential for large, long-duration fires and corresponding potential for high suppression expenditures. Modeling results generally confirmed that fire-treatment encounters are rare, such that median suppression cost savings are zero, but in extreme years, savings can more than offset upfront investments. Further, reductions in risk can expand areas where moderated suppression response would be appropriate, and these areas can be mapped in relation to fire control opportunities.

Factors affecting sodium hypochlorite extraction of CCA from treated wood.

Science.gov (United States)

Gezer, E D; Cooper, P A

2009-12-01

Significant amounts of chromated copper arsenate (CCA) treated wood products, such as utility poles and residential construction wood, remain in service. There is increasing public concern about environmental contamination from CCA-treated wood when it is removed from service for reuse or recycling, placed in landfills or burned in commercial incinerators. In this paper, we investigated the effects of time, temperature and sodium hypochlorite concentration on chromium oxidation and extraction of chromated copper arsenate from CCA-treated wood (Type C) removed from service. Of the conditions evaluated, reaction of milled wood with sodium hypochlorite for one hour at room temperature followed by heating at 75 degrees C for two hours gave the highest extraction efficiency. An average of 95% Cr, 99% Cu and 96% As could be removed from CCA-treated, milled wood by this process. Most of the extracted chromium was oxidized to the hexavalent state and could therefore be recycled in a CCA treating solution. Sodium hypochlorite extracting solutions could be reused several times to extract CCA components from additional treated wood samples.

Biomass burning in Africa: As assessment of annually burned biomass

International Nuclear Information System (INIS)

Delmas, R.A.; Loudjani, P.; Podaire, A.; Menaut, J.C.

1991-01-01

It is now established that biomass burning is the dominant phenomenon that controls the atmospheric chemistry in the tropics. Africa is certainly the continent where biomass burning under various aspects and processes is the greatest. Three different types of burnings have to be considered-bush fires in savanna zones which mainly affect herbaceous flora, forest fires due to forestation for shifting agriculture or colonization of new lands, and the use of wood as fuel. The net release of carbon resulting from deforestation is assumed to be responsible for about 20% of the CO 2 increase in the atmosphere because the burning of forests corresponds to a destorage of carbon from the biospheric reservoir. The amount of reactive of greenhouse gases emitted by biomass burning is directly proportional, through individual emission factors, to the biomass actually burned. This chapter evaluates the biomass annually burned on the African continent as a result of the three main burning processes previously mentioned

An experimental study on suspended sodium droplet combustion (2)

International Nuclear Information System (INIS)

Sato, Kenji

2004-03-01

As part of studies for phenomenological investigation of sodium droplet burning behavior, in our previous experimental studies for suspended single sodium droplet, behavior of ignition process and succeeding combustion, ignition delay time, and droplet temperature history had been investigated. In the present study, by using 4 mm diam. suspended sodium droplet, combustion experiments were performed for extended free-stream velocity range of dry air up to 200 cm/s, and for the initial droplet temperature T i =300degC and 400degC, and the effects of the free-stream velocity and initial droplet temperature on the ignition/burning behavior and ignition delay time were examined by using high speed video camera. The obtained experimental results are as follows: (1) Ignition phenomena of suspended spherical shape droplet were observed for all examined experimental conductions except the case of free-stream velocity U=200 cm/s at 300degC, where detachment of droplet from the support due to strained oxide film occurred. (2) The ignition delay time defined as the time to evolution of orange-light emitting zone or flame zone decreases with the increase of the free-stream velocity or of initial droplet temperature. Examples of typical ignition delay time are 0.68 s at U=20 cm/s, 0.52 s at U=100 cm/s, and 0.37 s at 200 cm/s for T i =400degC. (3) The orange-light emission at the moment of ignition occurs simultaneously over whole surface except the top region of the droplet. The intensity of the emission at the moment of ignition takes its maximum at the bottom region or upstream region of the droplet, and the emission intensity during the stable burning period increases with the increase of U. (4) When T i is 300degC, formation of temporal multiple short projections are observed before ignition for all examined free-stream velocities. The projections often do not disappear before ignition when the velocity is relatively high. (5) The layer or cloud composed of aerosol is formed

Effects of burn location and investigator on burn depth in a porcine model.

Science.gov (United States)

Singer, Adam J; Toussaint, Jimmy; Chung, Won Taek; Thode, Henry C; McClain, Steve; Raut, Vivek

2016-02-01

In order to be useful, animal models should be reproducible and consistent regardless of sampling bias, investigator creating burn, and burn location. We determined the variability in burn depth based on biopsy location, burn location and investigator in a porcine model of partial thickness burns. 24 partial thickness burns (2.5 cm by 2.5 cm each) were created on the backs of 2 anesthetized pigs by 2 investigators (one experienced, one inexperienced) using a previously validated model. In one of the pigs, the necrotic epidermis covering each burn was removed. Five full thickness 4mm punch biopsies were obtained 1h after injury from the four corners and center of the burns and stained with Hematoxylin and Eosin and Masson's trichrome for determination of burn depth by a board certified dermatopathologist blinded to burn location and investigator. Comparisons of burn depth by biopsy location, burn location and investigator were performed with t-tests and ANOVA as appropriate. The mean (SD) depth of injury to blood vessels (the main determinant of burn progression) in debrided and non-debrided pigs pooled together was 1.8 (0.3)mm, which included 75% of the dermal depth. Non-debrided burns were 0.24 mm deeper than debrided burns (Plocations, in debrided burns. Additionally, there were also no statistical differences in burn depths from midline to lateral in either of these burn types. Burn depth was similar for both investigators and among biopsy locations. Burn depth was greater for caudal locations in non-debrided burns and overall non-debrided burns were deeper than debrided burns. However, burn depth did not differ based on investigator, biopsy site, and medial-lateral location. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Density and shape factor of sodium aerosol. Final report, October 1, 1975--January 31, 1977

International Nuclear Information System (INIS)

Hinds, W.; Mallove, E.; First, M.W.

1977-04-01

Measurements were made of effective density, size distribution and dynamic shape factor for sodium fire aerosol particles using centrifugal separation and scanning electron microscopy. The aerosols were formed by burning one pound of sodium in a 90 m 3 air filled chamber at initial relative humidities from 16% to 53%. The aerosol particles were primarily sodium carbonate with water of hydration or adsorbed water. Twenty-nine samples of aerosols aged from 34-376 minutes gave an average value of effective density of 0.61 gm/cm 3 with relative standard deviation of 22%. This corresponds to a Stokes' correction factor, α, as used in the HAA-3 Code of 0.27. For the conditions of this study no clear trends were observed for effective density with relative humidity, age, or aerodynamic diameter

Burns caused by electronic vaping devices (e-cigarettes): A new classification proposal based on mechanisms.

Science.gov (United States)

Serror, K; Chaouat, M; Legrand, Matthieu M; Depret, F; Haddad, J; Malca, N; Mimoun, M; Boccara, D

2018-05-01

Introduction With more than 10 million of daily users, e-cigarettes encountered a great success. But in the past few years, the number of medical reports of injuries caused by the explosion of e-cigarettes has significantly increased. This article aims at reporting our series and reviewing the literature to propose a new classification based on the mechanisms of injuries related to e-cigarettes that can guide non-specialists and specialists in the management of these patients. Method We performed a retrospective review of our institutional burn database from June 2016 to July 2017 for injuries caused by or in the context of using an e-cigarette. The patients' demographics (age, gender), burn injury mechanisms, depth, localization, surface and interventions were described. Results Ten patients suffered from burns related to the use of e-cigarettes. The burns were located at the thigh (80%) and the hand (50%) with a mean surface of 3% of TBSA. Four different mechanisms could be described: Type A: thermal burns with flames due to the phenomenon of "thermal runaway", Type B: blasts lesions secondary to the explosion, Type C: chemical alkali burns caused by spreading of the electrolyte solution and Type D: thermal burns without flames due to overheating. These different mechanisms suggest specific surgical and non-surgical management. Conclusion Management of injuries sustained from e-cigarettes' explosions should be approached from the standpoint of mechanisms. Different mechanisms could be associated and should be considered in specific management. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

Universalist ethics in extraterrestrial encounter

Science.gov (United States)

Baum, Seth D.

2010-02-01

If humanity encounters an extraterrestrial civilization, or if two extraterrestrial civilizations encounter each other, then the outcome may depend not only on the civilizations' relative strength to destroy each other but also on what ethics are held by one or both civilizations. This paper explores outcomes of encounter scenarios in which one or both civilizations hold a universalist ethical framework. Several outcomes are possible in such scenarios, ranging from one civilization destroying the other to both civilizations racing to be the first to commit suicide. Thus, attention to the ethics of both humanity and extraterrestrials is warranted in human planning for such an encounter. Additionally, the possibility of such an encounter raises profound questions for contemporary human ethics, even if such an encounter never occurs.

LMR design concepts for transuranic management in low sodium void worth cores

International Nuclear Information System (INIS)

Hill, R.N.

1991-01-01

The fuel cycle processing techniques and hard neuron spectrum of the Integral Fast Reactor (IFR) metal fuel cycle have favorable characteristics for the management of transuranics; and the wide range of breeding characteristics available in metal fuelled cores provides for flexibility in transuranic management strategy. Previous studies indicate that most design options which decrease the breeding ratio also show a decrease in sodium void worth; therefore, low void worths are achievable in transuranic burning (low breeding ratio) core designs. This paper describes numerous trade studies assessing various design options for a low void worth transuranic burner core. A flat annular core design appears to be a promising concept; the high leakage geometry yields a low breeding ratio and small sodium void worth. To allow flexibility in breeding characteristics, alternate design options which achieve fissile self-sufficiency are also evaluated. A self-sufficient core design which is interchangeable with the burner core and maintains a low sodium void worth is developed. 13 refs., 1 fig., 4 tabs

LMR design concepts for transuranic management in low sodium void worth cores

International Nuclear Information System (INIS)

Hill, R.N.

1991-01-01

The fuel cycle processing techniques and hard neutron spectrum of the integral Fast Reactor (IFR) metal fuel cycle have favorable characteristics for the management of transuranics; and the wide range of breeding characteristics available in metal fuelled cores provides for flexibility in transuranic management strategy. Previous studies indicate that most design options which decrease the breeding ratio also allow a decrease in sodium void worth; therefore, low void worths are achievable in transuranic burning (low breeding ratio) core designs. This paper describes numerous trade studies assessing various design options for a low void worth transuranic burner core. A flat annular core design appears to be a promising concept; the high leakage geometry yields a low breeding ratio and small sodium void worth. To allow flexibility in breeding characteristics, alternate design options which achieve fissile self-sufficiency are also evaluated. A self-sufficient core design which is interchangeable with the burner core and maintains a low sodium void worth is developed. (author)

30 CFR 816.87 - Coal mine waste: Burning and burned waste utilization.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Burning and burned waste...-SURFACE MINING ACTIVITIES § 816.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or burned coal mine waste shall be removed from a permitted disposal...

Impact of a Newly Implemented Burn Protocol on Surgically Managed Partial Thickness Burns at a Specialized Burns Center in Singapore.

Science.gov (United States)

Tay, Khwee-Soon Vincent; Chong, Si-Jack; Tan, Bien-Keem

2016-03-01

This study evaluated the impact of a newly implemented protocol for superficial to mid-dermal partial thickness burns which involves early surgery and rapid coverage with biosynthetic dressing in a specialized national burns center in Singapore. Consecutive patients with 5% or greater total body surface area (TBSA) superficial to mid-dermal partial thickness burns injury admitted to the Burns Centre at the Singapore General Hospital between August and December 2014 for surgery within 48 hours of injury were prospectively recruited into the study to form the protocol group. Comparable historical cases from the year 2013 retrieved from the burns center audit database were used to form the historical control group. Demographics (age, sex), type and depth of burns, %TBSA burnt, number of operative sessions, and length of stay were recorded for each patient of both cohorts. Thirty-nine burns patients managed under the new protocol were compared with historical control (n = 39) comparable in age and extensiveness of burns. A significantly shorter length of stay (P burns was observed in the new protocol group (0.74 day/%TBSA) versus historical control (1.55 day/%TBSA). Fewer operative sessions were needed under the new protocol for burns 10% or greater TBSA burns (P protocol for surgically managed burns patients which involves early surgery and appropriate use of biosynthetic dressing on superficial to mid-dermal partial thickness burns. Clinically, shorter lengths of stay, fewer operative sessions, and decreased need for skin grafting of burns patient were observed.

Burns

Science.gov (United States)

A burn is damage to your body's tissues caused by heat, chemicals, electricity, sunlight, or radiation. Scalds from hot ... and gases are the most common causes of burns. Another kind is an inhalation injury, caused by ...

Solubilities of sodium nitrate, sodium nitrite, and sodium aluminate in simulated nuclear waste

International Nuclear Information System (INIS)

Reynolds, D.A.; Herting, D.L.

1984-09-01

Solubilities were determined for sodium nitrate, sodium nitrite, and sodium aluminate in synthetic nuclear waste liquor. Solubilities were determined as a function of temperature and solution composition (concentrations of sodium hydroxide, sodium nitrate, sodium nitrite, and sodium aluminate). Temperature had the greatest effect on the solubilities of sodium nitrate and sodium nitrite and a somewhat lesser effect on sodium aluminate solubility. Hydroxide had a great effect on the solubilities of all three salts. Other solution components had minor effects. 2 references, 8 figures, 11 tables

In-situ burning of heavy oils and Orimulsion : mid-scale burns

International Nuclear Information System (INIS)

Fingas, M.F.; Fieldhouse, B.; Brown, C.E.; Gamble, L.

2004-01-01

In-situ burning is considered to be a viable means to clean oil spills on water. In-situ burning, when performed under the right conditions, can reduce the volume of spilled oil and eliminate the need to collect, store, transport and dispose of the recovered oil. This paper presented the results of bench-scale in-situ burning tests in which Bunker C, Orimulsion and weathered bitumen were burned outdoors during the winter in burn pans of approximately 1 square metre. Each test was conducted on salt water which caused the separation of the bitumen from the water in the Orimulsion. Small amounts of diesel fuel was used to ignite the heavy oils. Quantitative removal of the fuels was achieved in all cases, but re-ignition was required for the Orimulsion. Maximum efficiency was in the order of 70 per cent. The residue was mostly asphaltenes and resins which cooled to a solid, glass like material that could be readily removed. The study showed that the type of oil burned influences the behaviour of the burns. Bunker C burned quite well and Orimulsion burned efficiently, but re-ignition was necessary. It was concluded that there is potential for burning heavy oils of several types in-situ. 6 refs., 7 tabs., 18 figs

Assessing burn depth in tattooed burn lesions with LASCA Imaging

Science.gov (United States)

Krezdorn, N.; Limbourg, A.; Paprottka, F.J.; Könneker; Ipaktchi, R.; Vogt, P.M

2016-01-01

Summary Tattoos are on the rise, and so are patients with tattooed burn lesions. A proper assessment with regard to burn depth is often impeded by the tattoo dye. Laser speckle contrast analysis (LASCA) is a technique that evaluates burn lesions via relative perfusion analysis. We assessed the effect of tattoo skin pigmentation on LASCA perfusion imaging in a multicolour tattooed patient. Depth of burn lesions in multi-coloured tattooed and untattooed skin was assessed using LASCA. Relative perfusion was measured in perfusion units (PU) and compared to various pigment colours, then correlated with the clinical evaluation of the lesion. Superficial partial thickness burn (SPTB) lesions showed significantly elevated perfusion units (PU) compared to normal skin; deep partial thickness burns showed decreased PU levels. PU of various tattoo pigments to normal skin showed either significantly lower values (blue, red, pink) or significantly increased values (black) whereas orange and yellow pigment showed values comparable to normal skin. In SPTB, black and blue pigment showed reduced perfusion; yellow pigment was similar to normal SPTB burn. Deep partial thickness burn (DPTB) lesions in tattoos did not show significant differences to normal DPTB lesions for black, green and red. Tattoo pigments alter the results of perfusion patterns assessed with LASCA both in normal and burned skin. Yellow pigments do not seem to interfere with LASCA assessment. However proper determination of burn depth both in SPTB and DPTB by LASCA is limited by the heterogenic alterations of the various pigment colours. PMID:28149254

Satisfaction with life after burn: A Burn Model System National Database Study.

Science.gov (United States)

Goverman, J; Mathews, K; Nadler, D; Henderson, E; McMullen, K; Herndon, D; Meyer, W; Fauerbach, J A; Wiechman, S; Carrougher, G; Ryan, C M; Schneider, J C

2016-08-01

While mortality rates after burn are low, physical and psychosocial impairments are common. Clinical research is focusing on reducing morbidity and optimizing quality of life. This study examines self-reported Satisfaction With Life Scale scores in a longitudinal, multicenter cohort of survivors of major burns. Risk factors associated with Satisfaction With Life Scale scores are identified. Data from the National Institute on Disability, Independent Living, and Rehabilitation Research (NIDILRR) Burn Model System (BMS) database for burn survivors greater than 9 years of age, from 1994 to 2014, were analyzed. Demographic and medical data were collected on each subject. The primary outcome measures were the individual items and total Satisfaction With Life Scale (SWLS) scores at time of hospital discharge (pre-burn recall period) and 6, 12, and 24 months after burn. The SWLS is a validated 5-item instrument with items rated on a 1-7 Likert scale. The differences in scores over time were determined and scores for burn survivors were also compared to a non-burn, healthy population. Step-wise regression analysis was performed to determine predictors of SWLS scores at different time intervals. The SWLS was completed at time of discharge (1129 patients), 6 months after burn (1231 patients), 12 months after burn (1123 patients), and 24 months after burn (959 patients). There were no statistically significant differences between these groups in terms of medical or injury demographics. The majority of the population was Caucasian (62.9%) and male (72.6%), with a mean TBSA burned of 22.3%. Mean total SWLS scores for burn survivors were unchanged and significantly below that of a non-burn population at all examined time points after burn. Although the mean SWLS score was unchanged over time, a large number of subjects demonstrated improvement or decrement of at least one SWLS category. Gender, TBSA burned, LOS, and school status were associated with SWLS scores at 6 months

Burning issues

International Nuclear Information System (INIS)

Raloff, J.

1993-01-01

The idea of burning oil slicks at sea has intrigued oil-cleanup managers for more than a decade, but it wasn't until the advent of fireproof booms in the mid-1980's and a major spill opportunity (the March 1989 Exxon Valdez) that in-situ burning got a real sea trial. The results of this and other burning experiments indicate that, when conditions allow it, nothing can compete with fire's ability to remove oil from water. Burns have the potential to remove as much oil in one day as mechanical devices can in one month, along with minimal equipment, labor and cost. Reluctance to burn in appropriate situations comes primarily from the formation of oily, black smoke. Analysis of the potentially toxic gases have been done, indicating that burning will not increase the levels of polluting aldehydes, ketones, dioxins, furans, and PAHs above those that normally evaporate from spilled oil. This article contains descriptions of planned oil fires and the discussion on the advantages and concerns of such a policy

30 CFR 817.87 - Coal mine waste: Burning and burned waste utilization.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Burning and burned waste...-UNDERGROUND MINING ACTIVITIES § 817.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or unburned coal mine waste shall be removed from a permitted disposal...

The role of resilience in the recovery of the burn-injured patient: an integrative review

Directory of Open Access Journals (Sweden)

Kornhaber R

2016-05-01

Full Text Available R Kornhaber,1 H Bridgman,2 L McLean,3–6 J Vandervord7 1School of Health Sciences, Faculty of Health, University of Tasmania, Hobart, TAS, 2Centre for Rural Health, School of Health Sciences, Faculty of Health, University of Tasmania, Hobart, TAS, 3Brain and Mind Centre, 4Westmead Psychotherapy Program, Discipline of Psychiatry, Sydney Medical School, University of Sydney, Sydney, NSW, 5Sydney West and Greater Southern Psychiatry Training Network, Cumberland Hospital, Western Sydney Local Health District, Sydney, NSW, 6Consultation-Liaison Psychiatry, Royal North Shore Hospital, Sydney, NSW, 7Severe Burns Injury Unit, Royal North Shore Hospital, St Leonards, NSW, Australia Abstract: Severe burn injuries are catastrophic life events resulting in significant physical and psychological effects. With long periods of hospitalization and rehabilitation, burn survivors encounter many issues, including an altered body image and loss of function and independence that subsequently influence quality of life and the family unit. Consequently, resilience has been identified as a fundamental concept that facilitates the adaptability required to navigate the lengthy and complex recovery process. However, over time, the notion of resilience has shifted from a static, innate trait to a fluid and multidimensional concept. Here, we review the evidence surrounding the role of resilience in the recovery of burn injury. This integrative review was based on a systematic search of five electronic databases. Of the 89 articles identified, ten primary research papers met the inclusion criteria. Three key themes were identified encompassing relational strengths, positive coping, and the resistance to trauma symptoms that are fundamental constructs associated with developing and sustaining resilience that resonate with the broader literature on burn recovery. However, limited evidence is currently available within the burns context. While resilience appears to be a vital

Genitalia burn: accident or violence? Concerns that transcend injury treatment

Directory of Open Access Journals (Sweden)

Ana Lúcia Ferreira

2014-06-01

Full Text Available OBJECTIVE: To describe a case of genital burn which raised the suspicion of maltreatment (sexual abuse and neglect by lack of supervision.CASE DESCRIPTION: An infant was taken to the Emergency Room of a pediatric hospital with an extensive burn in the vulva and perineum. The mother claimed the burn had been caused by a sodium-hydroxide-based product. However, the injury severity led to the suspicion of sexual abuse, which was then ruled out by a multidisciplinary team, based on the consistent report by the mother. Besides, the lesion type matched those caused by the chemical agent involved in the accident and the family context was evaluated and considered adequate. The patient had a favorable outcome and was discharged after four days of hospitalization. Outpatient follow-up during six months after the accident enabled the team to rule out neglect by lack of supervision.COMMENTS: Accidents and violence are frequent causes of physical injuries in children, and the differential diagnosis between them can be a challenge for healthcare workers, especially in rare clinical conditions involving patients who cannot speak for themselves. The involvement of a multidisciplinary trained team helps to have an adequate approach, ensuring child protection and developing a bond with the family; the latter is essential for a continued patient follow-up.

The improvement of control rod in experimental fast reactor JOYO. The development of a sodium bonded type control rod

Energy Technology Data Exchange (ETDEWEB)

Soga, T.; Miyakawa, S.; Mitsugi, T. [Japan Nuclear Cycle Development Inst., Oarai Engineering Center, Irradiation Center, Irradiation and Administration Section, Oarai, Ibaraki (Japan)

1999-06-01

Currently, the lifetime of control rods in JOYO is limited by Absorber-Cladding Mechanical Interaction (ACMI) due to swelling of B{sub 4}C(boron carbide) pellets accelerated by relocation of pellet fragments. A sodium bonded type control rod was developed which improves the thermal conductivity by means of charging sodium into the gap between B{sub 4}C and cladding and by utilizing a shroud which wraps the pellet fragments in a thin tube. This new design will be able to enlarge the gap between B{sub 4}C and cladding, without heating B{sub 4}C or fragment relocation, thus extending the life of the control rod. The sodium bonded type will be fabricated as the ninth reload control rods in JOYO. (1) The specification of a sodium bonded type control rod was determined with the wide gap between B{sub 4}C and cladding. In the design simulation, main component temperature were below the maximum limit. And the local heating by helium bubble generated from B{sub 4}C in the sodium gap, was not a serious problem in the analysis which was considered. (2) A structural design for the sodium entrance into the pin was determined. A formula was developed which the limit for sodium charging given physical dimension of the structure and sodium property. Result from sodium out-pile experiments validated the theoretical formula. (3) The analysis of ACMI indicated a lifetime extension of the sodium bonded type by 4.6% in comparison with lifetime of the helium bonded type of 1.6%. This is due to the boron10 burn-up rate being three times higher in the sodium bonded type than in the helium bonded type. To achieve a target burn-up 10% in the future, it will be necessary to modify design based on irradiation data which will be obtained by practical use of the sodium bonded control rods in JOYO. (4) The effects due to Absorber-Cladding Chemical Interaction (ACCI) were reduced by controlling the cladding temperature and chromium coating to the cladding's inner surface. It was confirmed

Global Burned Area and Biomass Burning Emissions from Small Fires

Science.gov (United States)

Randerson, J. T.; Chen, Y.; vanderWerf, G. R.; Rogers, B. M.; Morton, D. C.

2012-01-01

In several biomes, including croplands, wooded savannas, and tropical forests, many small fires occur each year that are well below the detection limit of the current generation of global burned area products derived from moderate resolution surface reflectance imagery. Although these fires often generate thermal anomalies that can be detected by satellites, their contributions to burned area and carbon fluxes have not been systematically quantified across different regions and continents. Here we developed a preliminary method for combining 1-km thermal anomalies (active fires) and 500 m burned area observations from the Moderate Resolution Imaging Spectroradiometer (MODIS) to estimate the influence of these fires. In our approach, we calculated the number of active fires inside and outside of 500 m burn scars derived from reflectance data. We estimated small fire burned area by computing the difference normalized burn ratio (dNBR) for these two sets of active fires and then combining these observations with other information. In a final step, we used the Global Fire Emissions Database version 3 (GFED3) biogeochemical model to estimate the impact of these fires on biomass burning emissions. We found that the spatial distribution of active fires and 500 m burned areas were in close agreement in ecosystems that experience large fires, including savannas across southern Africa and Australia and boreal forests in North America and Eurasia. In other areas, however, we observed many active fires outside of burned area perimeters. Fire radiative power was lower for this class of active fires. Small fires substantially increased burned area in several continental-scale regions, including Equatorial Asia (157%), Central America (143%), and Southeast Asia (90%) during 2001-2010. Globally, accounting for small fires increased total burned area by approximately by 35%, from 345 Mha/yr to 464 Mha/yr. A formal quantification of uncertainties was not possible, but sensitivity

Can we make an early 'do not resuscitate' decision in severe burn patients?

Science.gov (United States)

Yüce, Yücel; Acar, Hakan Ahmet; Erkal, Kutlu Hakan; Tuncay, Erhan

2017-03-01

The present study was conducted to examine topic of issuing early do-not-resuscitate (DNR) order at first diagnosis of patients with severe burn injuries in light of current law in Turkey and the medical literature. DNR requires withholding cardiopulmonary resuscitation in event of respiratory or cardiac arrest and allowing natural death to occur. It is frequently enacted for terminal cancer patients and elderly patients with irreversible neurological disorders. Between January 2009 and December 2014, 29 patients (3.44%) with very severe burns were admitted to burn unit. Average total burn surface area (TBSA) was 94.24% (range: 85-100%), and in 10 patients, TBSA was 100%. Additional inhalation burns were present in 26 of the patients (89.65%). All of the patients died, despite every medical intervention. Mean survival was 4.75 days (range: 1-24 days). Total of 17 patients died within 72 hours. Lethal dose 50 (% TBSA at which certain group has 50% chance of survival) rate of our burn center is 62%. Baux indices were used for prognostic evaluation of the patients; mean total Baux score of the patients was 154.13 (range: 117-183). It is well known that numerous problems may be encountered during triage of severely burned patients in Turkey. These patients are referred to burn centers and are frequently transferred via air ambulance between cities, and even countries. They are intubated and mechanical ventilation is initiated at burn center. Many interventions are performed to treat these patients, such as escharotomy, fasciotomy, tangential or fascial excision, central venous catheterization and tracheostomy, or hemodialysis. Yet despite such interventions, these patients die, typically within 48 to 96 hours. Integrity of the body is often lost as result of aggressive intervention with no real benefit, and there are also economic costs to hospital related to use of materials, bed occupancy, and distribution of workforce. For these reasons, as well as patient comfort

Understanding metropolitan patterns of daily encounters.

Science.gov (United States)

Sun, Lijun; Axhausen, Kay W; Lee, Der-Horng; Huang, Xianfeng

2013-08-20

Understanding of the mechanisms driving our daily face-to-face encounters is still limited; the field lacks large-scale datasets describing both individual behaviors and their collective interactions. However, here, with the help of travel smart card data, we uncover such encounter mechanisms and structures by constructing a time-resolved in-vehicle social encounter network on public buses in a city (about 5 million residents). Using a population scale dataset, we find physical encounters display reproducible temporal patterns, indicating that repeated encounters are regular and identical. On an individual scale, we find that collective regularities dominate distinct encounters' bounded nature. An individual's encounter capability is rooted in his/her daily behavioral regularity, explaining the emergence of "familiar strangers" in daily life. Strikingly, we find individuals with repeated encounters are not grouped into small communities, but become strongly connected over time, resulting in a large, but imperceptible, small-world contact network or "structure of co-presence" across the whole metropolitan area. Revealing the encounter pattern and identifying this large-scale contact network are crucial to understanding the dynamics in patterns of social acquaintances, collective human behaviors, and--particularly--disclosing the impact of human behavior on various diffusion/spreading processes.

A case-control evaluation of fungiform papillae density in burning mouth syndrome.

Science.gov (United States)

Naud, Jason M; Benca, Laura; Drangsholt, Mark T; LeResche, Linda; Coldwell, Susan E

2018-04-01

It has been hypothesized that high fungiform papillae density may be a risk factor for developing the taste and pain alterations characteristic of burning mouth syndrome. Evaluate whether fungiform papillae density, taste sensitivity, and mechanical pain sensitivity differ between burning mouth syndrome cases and controls. This case-control study compared cases diagnosed with primary burning mouth syndrome with pain-free controls. Participants (17 female cases and 23 female controls) rated the intensity of sucrose, sodium chloride, citric acid, and quinine applied separately to each side of the anterior tongue and sampled whole mouth. Mechanical pain sensitivity was assessed separately for each side of the tongue using weighted pins. Digital photographs of participants' tongues were used to count fungiform papillae. Burning mouth syndrome cases had increased whole mouth taste intensity. Cases also had increased sensitivity to quinine on the anterior tongue, as well as increased mechanical pain sensitivity on the anterior tongue. Fungiform papillae density did not differ significantly between cases and controls. Fungiform papillae density on the left and right sides of the tongue were correlated in controls; however, there was no left/right side correlation in cases. Cases had increased pain and taste perception on the anterior tongue. The lack of correlation between left and right fungiform papillae density in cases may be an indication of asymmetrical lingual innervation in these patients. 3b. Laryngoscope, 128:841-846, 2018. © 2017 The American Laryngological, Rhinological and Otological Society, Inc.

Innovative generativity of digital service encounters

DEFF Research Database (Denmark)

Henten, Anders; Sørensen, Jannick Kirk

2018-01-01

The research question examined in this chapter is how service encounters, based on digital interfaces, differ from face-to-face (f2f) encounters in terms of potential innovative generativity. New computer technologies facilitating big data processing and the development of advanced recommender...... systems and the recent developments of artificial intelligence with respect to cognitive and affective computing will certainly enhance the potential for innovations to be created on the basis of digital service encounters. However, the empathetic understanding of the needs and wants of the service users...... that can be part of the f2f service encounters cannot automatically result from digital service encounters. Digital tools can be developed and used to supplement the impressions that f2f encounters initiate. However, human interpretations and even human f2f encounters will also be needed to maintain...

Dialysate sodium and sodium gradient in maintenance hemodialysis: a neglected sodium restriction approach?

OpenAIRE

Munoz Mendoza, Jair; Sun, Sumi; Chertow, Glenn M.; Moran, John; Doss, Sheila; Schiller, Brigitte

2011-01-01

Background. A higher sodium gradient (dialysate sodium minus pre-dialysis plasma sodium) during hemodialysis (HD) has been associated with sodium loading; however, its role is not well studied. We hypothesized that a sodium dialysate prescription resulting in a higher sodium gradient is associated with increases in interdialytic weight gain (IDWG), blood pressure (BP) and thirst.

On the Burning of Plutonium Originating from Light Water Reactor Use in a Fast Molten Salt Reactor—A Neutron Physical Study

Directory of Open Access Journals (Sweden)

Bruno Merk

2015-11-01

Full Text Available An efficient burning of the plutonium produced during light water reactor (LWR operation has the potential to significantly improve the sustainability indices of LWR operations. The work offers a comparison of the efficiency of Pu burning in different reactor configurations—a molten salt fast reactor, a LWR with mixed oxide (MOX fuel, and a sodium cooled fast reactor. The calculations are performed using the HELIOS 2 code. All results are evaluated against the plutonium burning efficiency determined in the Consommation Accrue de Plutonium dans les Réacteurs à Neutrons RApides (CAPRA project. The results are discussed with special view on the increased sustainability of LWR use in the case of successful avoidance of an accumulation of Pu which otherwise would have to be forwarded to a final disposal. A strategic discussion is given about the unavoidable plutonium production, the possibility to burn the plutonium to avoid a burden for the future generations which would have to be controlled.

Burn mouse models

DEFF Research Database (Denmark)

Calum, Henrik; Høiby, Niels; Moser, Claus

2014-01-01

Severe thermal injury induces immunosuppression, involving all parts of the immune system, especially when large fractions of the total body surface area are affected. An animal model was established to characterize the burn-induced immunosuppression. In our novel mouse model a 6 % third-degree b......Severe thermal injury induces immunosuppression, involving all parts of the immune system, especially when large fractions of the total body surface area are affected. An animal model was established to characterize the burn-induced immunosuppression. In our novel mouse model a 6 % third...... with infected burn wound compared with the burn wound only group. The burn mouse model resembles the clinical situation and provides an opportunity to examine or develop new strategies like new antibiotics and immune therapy, in handling burn wound victims much....

Development of continuous energy Monte Carlo burn-up calculation code MVP-BURN

International Nuclear Information System (INIS)

Okumura, Keisuke; Nakagawa, Masayuki; Sasaki, Makoto

2001-01-01

Burn-up calculations based on the continuous energy Monte Carlo method became possible by development of MVP-BURN. To confirm the reliably of MVP-BURN, it was applied to the two numerical benchmark problems; cell burn-up calculations for High Conversion LWR lattice and BWR lattice with burnable poison rods. Major burn-up parameters have shown good agreements with the results obtained by a deterministic code (SRAC95). Furthermore, spent fuel composition calculated by MVP-BURN was compared with measured one. Atomic number densities of major actinides at 34 GWd/t could be predicted within 10% accuracy. (author)

Bacterial infections in burn patients at a burn hospital in Iran.

Science.gov (United States)

Ekrami, Alireza; Kalantar, Enayat

2007-12-01

The major challenge for a burn team is nosocomial infection in burn patients, which is known to cause over 50% of burn deaths. Most studies on infection in burn patients focus on burn wound infection, whereas other nosocomial infections in these patients are not well described. We undertook this study to determine three types of nosocomial infections viz., burn wound infection, urinary tract infection, and blood stream infection in burn patients in a burn hospital in Iran. During the one year period (May 2003 to April 2004), 182 patients were included in this study. Blood, urine and wound biopsy samples were taken 7 and 14 days after admission to Taleghani Burn hospital. Isolation and identification of microorganisms was done using the standard procedure. Disk diffusion test were performed for all the isolates for antimicrobial susceptibility. Of the 182 patients, 140 (76.9%) acquired at least one type of infection of the 140, 116 patients (82.8%) were culture positive on day 7 while 24 (17.2%) on 14 days after admission. Primary wound infection was most common (72.5%), followed by blood stream (18.6%) and urinary tract infections (8.9 %). The microorganisms causing infections were Pseudomonas aeruginosa (37.5%), Staphylococcus aureus (20.2%), and Acinetobacter baumanni (10.4%). Among these isolates P. aeruginosa was found to be 100 per cent resistant to amikacin, gentamicin , carbenicillin, ciprofloxacin, tobramycin and ceftazidime; 58 per cent of S. aureus and 60 per cent of coagulase negative Staphylococcus were methicillin resistant. High prevalence of nosocomial infections and the presence of multidrug resistant bacteria, and methicillin resistant S. aureus in patients at Taleghani Burn Hospital suggest continuous surveillance of burn infections and develop strategies for antimicrobial resistance control and treatment of infectious complications.

Comparing the reported burn conditions for different severity burns in porcine models: a systematic review.

Science.gov (United States)

Andrews, Christine J; Cuttle, Leila

2017-12-01

There are many porcine burn models that create burns using different materials (e.g. metal, water) and different burn conditions (e.g. temperature and duration of exposure). This review aims to determine whether a pooled analysis of these studies can provide insight into the burn materials and conditions required to create burns of a specific severity. A systematic review of 42 porcine burn studies describing the depth of burn injury with histological evaluation is presented. Inclusion criteria included thermal burns, burns created with a novel method or material, histological evaluation within 7 days post-burn and method for depth of injury assessment specified. Conditions causing deep dermal scald burns compared to contact burns of equivalent severity were disparate, with lower temperatures and shorter durations reported for scald burns (83°C for 14 seconds) compared to contact burns (111°C for 23 seconds). A valuable archive of the different mechanisms and materials used for porcine burn models is presented to aid design and optimisation of future models. Significantly, this review demonstrates the effect of the mechanism of injury on burn severity and that caution is recommended when burn conditions established by porcine contact burn models are used by regulators to guide scald burn prevention strategies. © 2017 Medicalhelplines.com Inc and John Wiley & Sons Ltd.

Burning Mouth Syndrome

Science.gov (United States)

... Care Home Health Info Health Topics Burning Mouth Burning Mouth Syndrome (BMS) is a painful, complex condition often described ... or other symptoms. Read More Publications Cover image Burning Mouth Syndrome Publication files Download Language English PDF — Number of ...

Full Core Burn-up Calculation at JRR-3 with MVP-BURN

International Nuclear Information System (INIS)

Komeda, Masao; Yamamoto, Kazuyoshi; Kusunoki, Tsuyoshi

2008-01-01

Research reactors use a burnable poison to suppress an excess reactivity in the beginning of reactor lifetime. The JRR-3 (Japan Research Reactor No.3) has used cadmium wires of radius 0.02 cm as a burnable poison. This report describes burn-up calculations of plate fuel models and full core models with MVP-BURN, which is a burn-up calculation code using Monte Carlo method and has been developed in JAEA (Japan Atomic Energy Agency). As the results of calculations of plate models, between a model composed of one burn-up region along the radius direction and a model composed of a few burn-up regions along the radius direction, the effective absorption cross section of 113 Cd has had different tendency on reaching approximate 40. day (10000 MWd/t). And as results of calculations of full core model, it has been indicated that k eff is almost same till approximate 80. day (22000 MWd/t) between a model composed of one burn-up region along the vertical direction and a model composed of a few burn-up regions along the vertical direction. However difference of 113 Cd burn-up becomes pronounced and each k eff makes a difference after 80. day. (authors)

Educational Materials - Burn Wise

Science.gov (United States)

Burn Wise outreach material. Burn Wise is a partnership program of that emphasizes the importance of burning the right wood, the right way, in the right wood-burning appliance to protect your home, health, and the air we breathe.

Encounters with immigrant customers

DEFF Research Database (Denmark)

Mygind, Anna; Espersen, Sacha; Nørgaard, Lotte Stig

2013-01-01

were not sufficiently assessed at the counter (n = 55, 65%), and that their latest encounter with an immigrant customer was less satisfactory than a similar encounter with an ethnic Danish customer (n = 48, 57%) (significantly more pharmacists than assistants: odds ratio, OR, 3.19; 95% confidence...

Management of a facial partial thickness chemical burn in a dog caused by bleach.

Science.gov (United States)

Kawalilak, Lukas T; Fransson, Boel A; Alessio, Terri L

2017-03-01

To describe the management and successful outcome of a late-recognition partial thickness bleach burn to the face and corneas of a dog. A 1-year-old male neutered Fox Terrier mix breed dog was evaluated for sloughing facial epithelium 5 days after coming into contact with an 8.25% household bleach cleaning solution. Severe erythema, edema, and crusting were noted around the muzzle and margins of both eyes, with moderate to severe alopecia in these areas. A partially detached, partial thickness eschar was present on the muzzle, while a firmly attached eschar was present in the region of both frontal sinuses. These injuries were consistent with a focal, superficial, and partial thickness chemical burn. Multiple ocular abnormalities, the most concerning of which was corneal ulceration, were also present. The patient's wounds were managed conservatively with limited surgical debridement of the affected epithelium 11 and 22 days after the initial exposure. Topical ocular medications, corneal debridement, and a superficial keratectomy were also used. All lesions resolved completely by 84 days postexposure, with no residual effects on the patient's quality of life. Chemical burns caused by contact with alkaline agents such as bleach (sodium hypochlorite) result in extensive necrosis of the skin and underlying structures. This is the first report of management alkaline facial burns in a dog. If inadequate or delayed hydrotherapy following exposure has resulted in superficial partial thickness burns, conservative management can be successful when traditional treatments, especially bandaging, are not feasible. © Veterinary Emergency and Critical Care Society 2017.

Core concepts for ''zero-sodium-void-worth core'' in metal fuelled fast reactor

International Nuclear Information System (INIS)

Chang, Y.I.; Hill, R.N.; Fujita, E.K.; Wade, D.C.; Kumaoka, Y.; Suzuki, M.; Kawashima, M.; Nakagawa, H.

1991-01-01

Core design options to reduce the sodium void worth in metal fueled LMRs are investigated. Two core designs which achieve a zero sodium void worth are analyzed in detail. The first design is a ''pancaked'' and annular core with enhanced transuranic burning capabilities; the high leakage in this design yields a low breeding ratio and small void worth. The second design is an axially multilayered annular core which is fissile self-sufficient; in this design, the upper and lower core regions are neutronically decoupled for reduced void worth while fissile self-sufficiency is achieved using internal axial blankets plus external radial and axial blanket zones. The neutronic performance characteristics of these low void worth designs are assessed here; their passive safety properties are discussed in a companion paper. 16 refs., 2 figs., 3 tabs

Core concepts for 'zero-sodium-void-worth core' in metal fuelled fast reactor

International Nuclear Information System (INIS)

Chang, Y.I.; Hill, R.N.; Fujita, E.K.; Wade, D.C.; Kumaoka, Y.; Suzuki, M.; Kawashima, M.; Nakagawa, H.

1991-01-01

Core design options to reduce the sodium void worth in metal fuelled LMRs are investigated. Two core designs which achieve a zero sodium void worth are analyzed in detail. The first design is a 'pancaked' and annular core with enhanced transuranic burning capabilities; the high leakage in this design yields a low breeding ratio and small void worth. The second design is an axially multilayered annular core which is fissile self-sufficient; in this design, the upper and lower core regions are neutronically decoupled for reduced void worth while fissile self-sufficiency is achieved using internal axial blankets plus external radial and axial blanket-zones. The neutronic performance characteristics of these low void worth designs are assessed here; their passive safety properties are discussed in a companion paper. (author)

Minor actinide burning in dedicated lead-bismuth cooled fast reactors

International Nuclear Information System (INIS)

Hejzlar, P.; Driscoll, M.J.; Kazimi, M.S.; Todreas, N.E.

2001-01-01

The destruction of minor actinides (MA) in dedicated burners is of contemporary interest in Europe and Japan because it requires the deployment of smaller number of special transmutation facilities. A major fraction of Pu from spent LWR fuel can be then burned in PWRs (or fast reactors) using dedicated fertile-free fuel assemblies. However, the design of MA burning fast spectrum cores poses significant challenges because of deterioration of key safety parameters, in particular of the coolant void coefficient. This study proposes the concept of an lead-bismuth eutectic (LBE)-cooled dedicated MA burner having metallic fuel (MA-Pu-Zr) and streaming assemblies to attain acceptable coolant void worth performance. It is shown that a large 1800 MWth fertile-free core containing 37 wt% TRU with very high fraction of MA(59 wt%) from LWR spent fuel can be burned in a first cycle for 700 EFPDs with a very small reactivity swing: less than β eff . Moreover, the reactivity void worth is negative for a fully voided core when all surrounding coolant is kept at reference density. However, the core reactivity increases as coolant density falls from the reference value of 10.25 to 6 g/cm 3 . Because its coolant density coefficient value is less than that of a sodium cooled IFR, the concept provides good potential for the achievement of self-regulation characteristics in unprotected events, provided that small negative fuel temperature feedback can be maintained. (authors)

Deciding Where to Burn: Stakeholder Priorities for Prescribed Burning of a Fire-Dependent Ecosystem

Directory of Open Access Journals (Sweden)

Jennifer K. Costanza

2011-03-01

Full Text Available Multiagency partnerships increasingly work cooperatively to plan and implement fire management. The stakeholders that comprise such partnerships differ in their perceptions of the benefits and risks of fire use or nonuse. These differences inform how different stakeholders prioritize sites for burning, constrain prescribed burning, and how they rationalize these priorities and constraints. Using a survey of individuals involved in the planning and implementation of prescribed fire in the Onslow Bight region of North Carolina, we examined how the constraints and priorities for burning in the longleaf pine (Pinus palustris ecosystem differed among three stakeholder groups: prescribed burn practitioners from agencies, practitioners from private companies, and nonpractitioners. Stakeholder groups did not differ in their perceptions of constraints to burning, and development near potentially burned sites was the most important constraint identified. The top criteria used by stakeholders to decide where to burn were the time since a site was last burned, and a site's ecosystem health, with preference given to recently burned sites in good health. Differences among stakeholder groups almost always pertained to perceptions of the nonecological impacts of burning. Prescribed burning priorities of the two groups of practitioners, and particularly practitioners from private companies, tended to be most influenced by nonecological impacts, especially through deprioritization of sites that have not been burned recently or are in the wildland-urban interface (WUI. Our results highlight the difficulty of burning these sites, despite widespread laws in the southeast U.S. that limit liability of prescribed burn practitioners. To avoid ecosystem degradation on sites that are challenging to burn, particularly those in the WUI, conservation partnerships can facilitate demonstration projects involving public and private burn practitioners on those sites. In summary

Epidemiology of burns

NARCIS (Netherlands)

Dokter, Jan

2016-01-01

The aim of this thesis is to understand the epidemiology, treatment and outcomes of specialized burn care in The Netherlands. This thesis is mainly based on historical data of the burn centre in Rotterdam from 1986, combined with historical data from the burn centres in Groningen and Beverwijk from

Polymeric Films Loaded with Vitamin E and Aloe vera for Topical Application in the Treatment of Burn Wounds

Directory of Open Access Journals (Sweden)

Gabriela Garrastazu Pereira

2014-01-01

Full Text Available Burns are serious traumas related to skin damage, causing extreme pain and possibly death. Natural drugs such as Aloe vera and vitamin E have been demonstrated to be beneficial in formulations for wound healing. The aim of this work is to develop and evaluate polymeric films containing Aloe vera and vitamin E to treat wounds caused by burns. Polymeric films containing different quantities of sodium alginate and polyvinyl alcohol (PVA were characterized for their mechanical properties and drug release. The polymeric films, which were produced, were thin, flexible, resistant, and suitable for application on damaged skin, such as in burn wounds. Around 30% of vitamin E acetate was released from the polymeric films within 12 hours. The in vivo experiments with tape stripping indicated an effective accumulation in the stratum corneum when compared to a commercial cream containing the same quantity of vitamin E acetate. Vitamin E acetate was found in higher quantities in the deep layers of the stratum corneum when the film formulation was applied. The results obtained show that the bioadhesive films containing vitamin E acetate and Aloe vera could be an innovative therapeutic system for the treatment of burns.

Polymeric films loaded with vitamin E and aloe vera for topical application in the treatment of burn wounds.

Science.gov (United States)

Pereira, Gabriela Garrastazu; Guterres, Sílvia Stanisçuaki; Balducci, Anna Giulia; Colombo, Paolo; Sonvico, Fabio

2014-01-01

Burns are serious traumas related to skin damage, causing extreme pain and possibly death. Natural drugs such as Aloe vera and vitamin E have been demonstrated to be beneficial in formulations for wound healing. The aim of this work is to develop and evaluate polymeric films containing Aloe vera and vitamin E to treat wounds caused by burns. Polymeric films containing different quantities of sodium alginate and polyvinyl alcohol (PVA) were characterized for their mechanical properties and drug release. The polymeric films, which were produced, were thin, flexible, resistant, and suitable for application on damaged skin, such as in burn wounds. Around 30% of vitamin E acetate was released from the polymeric films within 12 hours. The in vivo experiments with tape stripping indicated an effective accumulation in the stratum corneum when compared to a commercial cream containing the same quantity of vitamin E acetate. Vitamin E acetate was found in higher quantities in the deep layers of the stratum corneum when the film formulation was applied. The results obtained show that the bioadhesive films containing vitamin E acetate and Aloe vera could be an innovative therapeutic system for the treatment of burns.

Burns and military clothing.

Science.gov (United States)

McLean, A D

2001-02-01

Burn injury is a ubiquitous threat in the military environment. The risks during combat are well recognised, but the handling of fuel, oil, munitions and other hot or flammable materials during peacetime deployment and training also imposes an inherent risk of accidental burn injury. Over the last hundred years, the burn threat in combat has ranged from nuclear weapons to small shoulder-launched missiles. Materials such as napalm and white phosphorus plainly present a risk of burn, but the threat extends to encompass personnel in vehicles attacked by anti-armour weapons, large missiles, fuel-air explosives and detonations/conflagrations on weapons platforms such as ships. Large numbers of burn casualties were caused at Pearl Harbor, in Hiroshima and Nagasaki, Vietnam, during the Arab/Israeli Wars and in the Falkland Islands conflict. The threat from burns is unlikely to diminish, indeed new developments in weapons seek to exploit the vulnerability of the serviceman and servicewoman to burns. Clothing can be a barrier to some types of burn--both inherently in the properties of the material, but also by trapping air between clothing layers. Conversely, ignition of the clothing may exacerbate a burn. There is hearsay that burnt clothing products within a wound may complicate the clinical management, or that materials that melt (thermoplastic materials) should not be worn if there is a burn threat. This paper explores the incidence of burn injury, the mechanisms of heat transfer to bare skin and skin covered by materials, and the published evidence for the complication of wound management by materials. Even light-weight combat clothing can offer significant protection to skin from short duration flash burns; the most vulnerable areas are the parts of the body not covered--face and hands. Multilayered combat clothing can offer significant protection for short periods from engulfment by flames; lightweight tropical wear with few layers offers little protection. Under

Ceruloplasmin and Hypoferremia: Studies in Burn and Non-Burn Trauma Patients

Science.gov (United States)

2015-03-06

ceruloplasmin; ferroxidase; iron status; oxidant stress; burn; trauma 1. Introduction Iron is an essential element for life that facilitates...899–906. 45. Shakespeare , P.G. Studies on the serum levels of iron, copper and zinc and the urinary excretion of zinc after burn injury. Burns Incl

Pediatric Burns from Glass-Fronted Fireplaces in Canada: A Growing Issue Over the Past 20 Years.

Science.gov (United States)

Toor, Jay; Crain, Jennifer; Kelly, Charis; Verchere, Cindy; Fish, Joel

2016-01-01

There is an alarming lack of public awareness surrounding the safety of glass-fronted fireplaces. This has resulted in an active campaign from the American Burn Association Prevention Committee. One issue encountered while advocating for prevention among manufacturers is the lack of corroborating and accurate data. The purpose of this study was to examine the annual trends and epidemiology of glass-fronted fireplace-related burn injuries to children less than 15 years old, who presented to Canadian emergency departments between 1990 and 2010. Records of pediatric burn injuries related to glass-fronted fireplaces were extracted from the Canadian Hospitals Injury Reporting and Prevention Program database for the study period (1990-2010). Cases were analyzed in terms of anatomic area affected, demographics, seasonality, safety device use, and injury severity. A total of 616 cases of burns from glass-fronted fireplaces were identified. The incidence increased at an average of 2.7 cases per year. This is a greater than 20-fold increase over 20 years. Seventy-five percentage of the cases occurred in children less than 2 years, and 95% occurred in children less than 5 years. The study demonstrated a growing risk from glass-fronted fireplace burns, likely due to the increasing popularity of household gas fireplace units. These units are a particular risk to children less than 2 years, attributable to their developing mobility and reduced reaction time. This is a preventable injury that should be addressed through changes to legislation and manufacturing.

Design and selection of materials for sodium cooled fast reactors

International Nuclear Information System (INIS)

Chetal, S.C.

2011-01-01

Sodium cooled fast reactors are currently in operation, under construction or under design by a number of countries. The design of sodium cooled fast reactor is covered by French RCC - MR code and ASME code NH. The codes cover rules as regards to materials, design and construction. These codes do not cover the effect of irradiation and environment. Elevated temperature design criteria in nuclear codes are much stringent in comparison to non nuclear codes. Sodium corrosion is not an issue in selection of materials provided oxygen impurity in sodium is controlled for which excellent reactor operating experience is available. Austenitic stainless steels have remained the choice for the permanent structures of primary sodium system. Stabilized austenitic stainless steel are rejected because of poor operating experience and non inclusion in the design codes. Route for improved creep behaviour lies in compositional modifications in 316 class steel. However, the weldability needs to be ensured. For cold leg component is non creep regime, SS 304 class steel is favoured from overall economics. Enhanced fuel burn up can be realized by the use of 9-12%Cr 1%Mo class steel for the wrapper of MOX fuel design, and cladding and wrapper for metal fuel reactors. Minor compositional modifications of 20% cold worked 15Cr-15Ni class austenitic stainless steel will be a strong candidate for the cladding of MOX fuel design in the short term. Long term objective for the cladding will be to develop oxide dispersion strengthened steel. 9%Cr 1%Mo class steel (Gr 91) is an ideal choice for integrated once through sodium heated steam generators. One needs to incorporate operating experience from reactors and thermal power stations, industrial capability and R and D feedback in preparing the technical specifications for procurement of wrought products and welding consumables to ensure reliable operation of the components and systems over the design life. The paper highlights the design approach

Stream Lifetimes Against Planetary Encounters

Science.gov (United States)

Valsecchi, G. B.; Lega, E.; Froeschle, Cl.

2011-01-01

We study, both analytically and numerically, the perturbation induced by an encounter with a planet on a meteoroid stream. Our analytical tool is the extension of pik s theory of close encounters, that we apply to streams described by geocentric variables. The resulting formulae are used to compute the rate at which a stream is dispersed by planetary encounters into the sporadic background. We have verified the accuracy of the analytical model using a numerical test.

Effectiveness of Chlorinated Water, Sodium Hypochlorite, Sodium ...

African Journals Online (AJOL)

This study evaluated the efficacy of chlorinated water, sodium hypochlorite solution, sodium chloride solution and sterile distilled water in eliminating pathogenic bacteria on the surfaces of raw vegetables. Lettuce vegetables were dipped in different concentrations of chlorinated water, sodium hypochlorite solution, sodium ...

Study on MAs transmutation of accelerator-driven system sodium-cooled fast reactor loaded with metallic fuel

International Nuclear Information System (INIS)

Han Song; Yang Yongwei

2007-01-01

Through the analysis of the effect of heavy metal actinides on the effective multiplication constant (k eff ) of the core in accelerator-driven system (ADS) sodium-cooled fast reactor loaded with metallic fuel, we gave the method for determining fuel components. the characteristics of minor actinides (MAs) transmutation was analyzed in detail. 3D burn-up code COUPLE, which couples MCNP4c3 and ORIGEN2, was applied to the neutron simulation and burn up calculation. The results of optimized scheme shows that adjusting the proportion of 239 Pu and maintaining the value during the burn-up cycle is an efficient method of designing k eff and keeping stable during the burn-up cycle. Spallation neutrons lead to the neutron spectrum harder at inner core than that at outer core. It is in favor of improving MA's fission cross sections and the capture-to-fission ratio. The total MAs transmutation support ratio 8.3 achieves excellent transmutation effect. For higher flux at inner core leads to obvious differences on transmutation efficiency,only disposing MAs at inner core is in favor of decreasing the loading mass and improving MAs transmutation effect. (authors)

Burn Wise

Science.gov (United States)

Burn Wise is a partnership program of the U.S. Environmental Protection Agency that emphasizes the importance of burning the right wood, the right way, in the right appliance to protect your home, health, and the air we breathe.

Effects of radiation, burn and combined radiation-burn injury on hemodynamics

International Nuclear Information System (INIS)

Ye Benlan; Cheng Tianming; Xiao Jiasi

1996-01-01

Changes in hemodynamics after radiation, burn and combined radiation burn injury within eight hours post injury were studied. The results indicate: (1) Shock of rats in the combined injury group is more severe than that in the burn group. One of the reasons is that the blood volume in the combined injury group is less than that in the burn group. Radiation injury plays an important role in this effect, which enhances the increase in vascular permeability and causes the loss of plasma. (2) Decrease in cardiac output and stroke work and increase in vascular resistance in the combined radiation burn group are more drastic than those in the burn group, which may cause and enhance shock. Replenishing fluid is useful for recovery of hemodynamics. (3) Rb uptake is increased in the radiation group which indicates that compensated increase of myocardial nutritional blood flow may take place before the changes of hemodynamics and shock. Changes of Rb uptake in the combined injury group is different from that in the radiation groups and in the burn group. The results also suggest that changes of ion channel activities may occur to a different extent after injury. (4) Verapamil is helpful to the recovery of hemodynamics post injury. It is better to combine verapamil with replenishing fluid

Outcomes of burns in the elderly: revised estimates from the Birmingham Burn Centre.

Science.gov (United States)

Wearn, Christopher; Hardwicke, Joseph; Kitsios, Andreas; Siddons, Victoria; Nightingale, Peter; Moiemen, Naiem

2015-09-01

Outcomes after burn have continued to improve over the last 70 years in all age groups including the elderly. However, concerns have been raised that survival gains have not been to the same magnitude in elderly patients compared to younger age groups. The aims of this study were to analyze the recent outcomes of elderly burn injured patients admitted to the Birmingham Burn Centre, compare data with a historical cohort and published data from other burn centres worldwide. A retrospective review was conducted of all patients ≥65 years of age, admitted to our centre with cutaneous burns, between 2004 and 2012. Data was compared to a previously published historical cohort (1999-2003). 228 patients were included. The observed mortality for the study group was 14.9%. The median age of the study group was 79 years, the male to female ratio was 1:1 and median Total Body Surface Area (TBSA) burned was 5%. The incidence of inhalation injury was 13%. Median length of stay per TBSA burned for survivors was 2.4 days/% TBSA. Mortality has improved in all burn size groups, but differences were highly statistically significant in the medium burn size group (10-20% TBSA, p≤0.001). Burn outcomes in the elderly have improved over the last decade. This reduction has been impacted by a reduction in overall injury severity but is also likely due to general improvements in burn care, improved infrastructure, implementation of clinical guidelines and increased multi-disciplinary support, including Geriatric physicians. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

The Art of the Encounter

Directory of Open Access Journals (Sweden)

Éric Vautrin

2013-03-01

Full Text Available As the archives from the second half of Grotowski’s life were made available, this text focuses on the Polish master’s conceptions of theatre where he describes theatre as the art of the encounter. This paper simultaneously places this proposition in the context of questions of a specific time period, and reveals how this encounter is the anathema that will revert viewpoints both about the art of acting and the creation of theatrical relations. These researches on theatre as the art of the encounter continue today through the Open Program, one of the two groups of the Workcenter of Jerzy Grotowski and Thomas Richards, and, notably, their creations around American poet Allen Ginsberg, an author whose poetry intends, in a similar way, to encounter the other and the world.

Wound management and outcome of 595 electrical burns in a major burn center.

Science.gov (United States)

Li, Haisheng; Tan, Jianglin; Zhou, Junyi; Yuan, Zhiqiang; Zhang, Jiaping; Peng, Yizhi; Wu, Jun; Luo, Gaoxing

2017-06-15

Electrical burns are important causes of trauma worldwide. This study aims to analyze the clinical characteristics, wound management, and outcome of electric burns. This retrospective study was performed at the Institute of Burn Research of the Third Military Medical University during 2013-2015. Data including the demographics, injury patterns, wound treatment, and outcomes were collected and analyzed. A total of 595 electrical burn patients (93.8% males) were included. The average age was 37.3 ± 14.6 y, and most patients (73.5%) were aged 19∼50 years. Most patients (67.2%) were injured in work-related circumstances. The mean total body surface area was 8.8 ± 11.8% and most wounds (63.5%) were full-thickness burns. Operation times of high-voltage burns and current burns were higher than those of low-voltage burns and arc burns, respectively. Of the 375 operated patients, 83.2% (n = 312) underwent skin autografting and 49.3% (n = 185) required skin flap coverage. Common types of skin flaps were adjacent (50.3%), random (42.2%), and pedicle (35.7%). Amputation was performed in 107 cases (18.0%) and concentrated on the hands (43.9%) and upper limbs (39.3%). The mean length of stay was 42.9 ± 46.3 d and only one death occurred (0.2%). Current burns and higher numbers of operations were major risk factors for amputation and length of stay, respectively. Electrical burns mainly affected adult males with occupational exposures in China. Skin autografts and various skin flaps were commonly used for electric burn wound management. More standardized and effective strategies of treatment and prevention are still needed to decrease amputation rates. Copyright © 2017 Elsevier Inc. All rights reserved.

Burning mouth syndrome

Directory of Open Access Journals (Sweden)

K A Kamala

2016-01-01

Full Text Available Burning mouth syndrome (BMS is multifactorial in origin which is typically characterized by burning and painful sensation in an oral cavity demonstrating clinically normal mucosa. Although the cause of BMS is not known, a complex association of biological and psychological factors has been identified, suggesting the existence of a multifactorial etiology. As the symptom of oral burning is seen in various pathological conditions, it is essential for a clinician to be aware of how to differentiate between symptom of oral burning and BMS. An interdisciplinary and systematic approach is required for better patient management. The purpose of this study was to provide the practitioner with an understanding of the local, systemic, and psychosocial factors which may be responsible for oral burning associated with BMS, and review of treatment modalities, therefore providing a foundation for diagnosis and treatment of BMS.

Assessment of burn-specific health-related quality of life and patient scar status following burn.

Science.gov (United States)

Oh, Hyunjin; Boo, Sunjoo

2017-11-01

This study assessed patient-perceived levels of scar assessment and burn-specific quality of life (QOL) in Korean burn patients admitted to burn care centers and identified differences in scar assessment and QOL based on various patient characteristics. A cross-sectional descriptive study using anonymous paper-based survey methods was conducted with 100 burn patients from three burn centers specializing in burn care in South Korea. Mean subject age was 44.5 years old, and 69% of the subjects were men. The overall mean QOL was 2.91 out of 5. QOL was lowest for the work subdomain (2.25±1.45) followed by the treatment regimen subdomain (2.32±1.16). The subjects' mean total scar assessment score was 35.51 out of 60, and subjects were most unsatisfied with scar color. Subjects with low income, flame-source burns, severe burns, visible scars, and scars on face or hand reported significantly lower QOL. Subjects with severe burn degree and burn range perceived their burn scar condition to be worse than that of others. The results show that burn subjects experience the most difficulties with their work and the treatment regimen. Subjects with severe burn and visible scarring have a reduced QOL and a poor scar status. Scar management intervention may improve QOL of burn patients especially those with severe burn and visible scars. Further studies are warranted to evaluate the relationship between scar assessment and QOL. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

The epidemology of burn injuries of children and the importance of modern burn centre

Directory of Open Access Journals (Sweden)

Janez Mohar

2007-01-01

Full Text Available Background: Burns represent the major percentage of injuries to children. Their incidence level, injury mechanisms and treatment often differ from the burn injuries of adults.Methods: From the medical records of the Department for Plastic and Reconstructive Surgery of the Ljubljana Medical Centre we gathered, analyzed and compared the burn injuries of children up to the age of 15 who were admitted to hospital in the year 2003 to those who were treated as outpatients. Moreover, we compared the burn injuries of hospitalized children at the same department in the years 2003, 1993 and 1983 respectively. We compared their gender, age, the total body surface area of burns, the depth of burns, frequency of the mechanisms of injury, the affected parts of the body and the length and mode of treatment. Finally, we compared our results with the results of similar studies from other burn centres.Results: The number of children treated for burns at the department has declined. In all the years studied, the injured children were younger than 5 and the majority of them were boys. The number of children admitted with substantial total body surface areas of burns was also declining. However, there was an increase in the number of children admitted with burns less than 10 % of their total body surface area. The number of burns treated by surgery slightly increased over the years studied. There was a similar sex and age distribution among the hospitalized children and those treated as outpatients.Conclusions: The number of children hospitalized with burns is in decline. In the years 1983, 1993 and 2003, there was no significant difference in the percentage of children who were treated surgically and those who were treated conservatively (P = 0.247. The Burn Centre at the Department for Plastic and Reconstructive Surgery of the Ljubljana Medical Centre which together with the Burn Department of the Maribor General Hospital covers the population of two million

Pediatric burns: Kids' Inpatient Database vs the National Burn Repository.

Science.gov (United States)

Soleimani, Tahereh; Evans, Tyler A; Sood, Rajiv; Hartman, Brett C; Hadad, Ivan; Tholpady, Sunil S

2016-04-01

Burn injuries are one of the leading causes of morbidity and mortality in young children. The Kids' Inpatient Database (KID) and National Burn Repository (NBR) are two large national databases that can be used to evaluate outcomes and help quality improvement in burn care. Differences in the design of the KID and NBR could lead to differing results affecting resultant conclusions and quality improvement programs. This study was designed to validate the use of KID for burn epidemiologic studies, as an adjunct to the NBR. Using the KID (2003, 2006, and 2009), a total of 17,300 nonelective burn patients younger than 20 y old were identified. Data from 13,828 similar patients were collected from the NBR. Outcome variables were compared between the two databases. Comparisons revealed similar patient distribution by gender, race, and burn size. Inhalation injury was more common among the NBR patients and was associated with increased mortality. The rates of respiratory failure, wound infection, cellulitis, sepsis, and urinary tract infection were higher in the KID. Multiple regression analysis adjusting for potential confounders demonstrated similar mortality rate but significantly longer length of stay for patients in the NBR. Despite differences in the design and sampling of the KID and NBR, the overall demographic and mortality results are similar. The differences in complication rate and length of stay should be explored by further studies to clarify underlying causes. Investigations into these differences should also better inform strategies to improve burn prevention and treatment. Copyright © 2016 Elsevier Inc. All rights reserved.

Encounter with comet Halley

International Nuclear Information System (INIS)

Sagdeev, R.Z.

1989-01-01

This paper reports on an international armada of six spacecraft which encountered the comet Halley and performed in-situ measurements. These encounters led to the discovery of a number of cometary plasma physics phenomena. Another important result was that a value for the average density of the cometary nucleus could be estimated, which is found to be compatible with snow ball models for the nucleus

The Idealized Cultural Encounter

DEFF Research Database (Denmark)

Christiansen, Lene Bull

Studies into cultural encounters have predominantly taken point of departure in ‘problematic encounters’, in which researchers and participants see cultural difference as an obstacle on the road to harmonious relationships (e.g. in ‘the clash of civilisations,’ or in migration/integration studies......). This paper proposes to study cultural encounters which are organised around ideals of cultural difference as a positive social and political force. The Danish People to People NGO Mellemfolkeligt Samvirke (MS) is build around ideals of equality, co-operation, mutuality and solidarity between people...... and cultures. A prominent feature of the organisation is organised cultural encounters between Northern (predominantly Danish) volunteers and Africans, which takes place at ‘training centres’ both in Denmark and in African countries, such as Kenya or Tanzania. In this paper I will outline the theoretical...

Conclusive experimental study of prevention measures against sodium combustion residuum reignition. Run-F9-1, Run-F9-2

International Nuclear Information System (INIS)

Ishikawa, Hiroyasu; Ohno, Shuji; Miyahara, Shinya

2004-04-01

Nitrogen gas can be an extinguisher or a mitigating material in the case of sodium leak and fire accident in an air atmosphere, which may occur at a liquid metal cooled nuclear power plant. However, sodium combustion residuum sometimes reignites in the air atmosphere even at room temperature when it was produced by nitrogen gas injection to the burning sodium. Then, in this study we executed conclusive experiments of prevention measures against sodium combustion residuum reignition by a mixture of carbon-dioxide (CO 2 ) gas, humidity and nitrogen gas. The experiments were carried out with the FRAT-1 test equipment; the humidity conditions were changed in air which were used to sodium combustion atmosphere and exposure air for confirmation of prevented combustion residue reignition. First of all, the sodium of about 2.5 kg was leaked in air atmosphere, and next, the sodium combustion was stopped by nitrogen gas injection. Next, the combustion residuum was cooled in the nitrogen atmosphere, and then the combustion residuum was exposed to atmosphere of carbon-dioxide (4%); humidity (6000vppm); oxygen (3%)-nitrogen (based gas) mixture. It was confirmed that the combustion residuum was not reignition even if exposed to the air atmosphere again at the end of experiment. We had confirmed that the prevention measures against sodium combustion residuum reignition to establish by this research were effective. (author)

Improved Survival of Patients With Extensive Burns: Trends in Patient Characteristics and Mortality Among Burn Patients in a Tertiary Care Burn Facility, 2004-2013.

Science.gov (United States)

Strassle, Paula D; Williams, Felicia N; Napravnik, Sonia; van Duin, David; Weber, David J; Charles, Anthony; Cairns, Bruce A; Jones, Samuel W

Classic determinants of burn mortality are age, burn size, and the presence of inhalation injury. Our objective was to describe temporal trends in patient and burn characteristics, inpatient mortality, and the relationship between these characteristics and inpatient mortality over time. All patients aged 18 years or older and admitted with burn injury, including inhalation injury only, between 2004 and 2013 were included. Adjusted Cox proportional hazards regression models were used to estimate the relationship between admit year and inpatient mortality. A total of 5540 patients were admitted between 2004 and 2013. Significant differences in sex, race/ethnicity, burn mechanisms, TBSA, inhalation injury, and inpatient mortality were observed across calendar years. Patients admitted between 2011 and 2013 were more likely to be women, non-Hispanic Caucasian, with smaller burn size, and less likely to have an inhalation injury, in comparison with patients admitted from 2004 to 2010. After controlling for patient demographics, burn mechanisms, and differential lengths of stay, no calendar year trends in inpatient mortality were detected. However, a significant decrease in inpatient mortality was observed among patients with extensive burns (≥75% TBSA) in more recent calendar years. This large, tertiary care referral burn center has maintained low inpatient mortality rates among burn patients over the past 10 years. While observed decreases in mortality during this time are largely due to changes in patient and burn characteristics, survival among patients with extensive burns has improved.

The Burning Saints

DEFF Research Database (Denmark)

Xygalatas, Dimitris

. Carrying the sacred icons of the saints, participants dance over hot coals as the saint moves them. The Burning Saints presents an analysis of these rituals and the psychology behind them. Based on long-term fieldwork, The Burning Saints traces the historical development and sociocultural context......, The Burning Saints presents a highly original analysis of how mental processes can shape social and religious behaviour....

Experimental study of the consequences of accidental sodium release in the form of peroxide aerosols on the tomato and the lettuce

International Nuclear Information System (INIS)

Camus, H.; Delmas, J.; Grauby, A.; Disdier, R.

1977-01-01

Industrial development of sodium cooled breeder reactors have lead to the study of consequences of accidents occuring in the cooling circuit. The effects on crops when aerosols are released in the atmosphere can be determined after a certain amount of molten sodium (stable element 23 Na) is brought into contact with the open air. Experiments are performed in a 'Phytotron' equipment on lettuces and tomatoes in dry atmosphere at two different moments during the growing process. The aerosol studied has a high content of sodium peroxide and the ground deposit varied between 17 and 450 mg/m 2 sodium equivalent. (Concentration at distances of 800 m and 1500 m calculated for a theoretical fire involving 10 tons of sodium). Necrosis, visible only with a microscope, were reported when deposits in sodium equivalent were under 300 mg/m 2 . Leaves were destroyed if necrosis were numerous (deposit above 300 mg/m 2 ). Tomatoes, and fruits in particular, were found to be more resistant than lettuces. Sodium embedded in dead cells does not migrate in the plant and does not disturb the plants physiological equilibrium. New sprouts have normal sodium percentage. The consequences are essentially burns of which the extent is more or less high depending on the deposits and the kind of species involved [fr

Covering techniques for severe burn treatment: lessons for radiological burn accidents

International Nuclear Information System (INIS)

Carsin, H.; Stephanazzi, J.; Lambert, F.; Curet, P.M.; Gourmelon, P.

2002-01-01

Covering techniques for severe burn treatment: lessons for radiological burn accidents. After a severe burn, the injured person is weakened by a risk of infection and a general inflammation. The necrotic tissues have to be removed because they are toxic for the organism. The injured person also needs to be covered by a cutaneous envelope, which has to be done by a treatment centre for burned people. The different techniques are the following: - auto grafts on limited burned areas; - cutaneous substitutes to cover temporary extended burned areas. Among them: natural substitutes like xenografts (pork skin, sheep skin,..) or allografts (human skin), - treated natural substitutes which only maintain the extracellular matrix. Artificial skins belong to this category and allow the development of high quality scars, - cell cultures in the laboratory: multiplying the individual cells and grafting them onto the patient. This technique is not common but allows one to heal severely injured patients. X-ray burns are still a problem. Their characteristics are analysed: intensive, permanent, antalgic resistant pain. They are difficult to compare with heat burns. In spite of a small number of known cases, we can give some comments and guidance on radio necrosis cures: the importance of the patients comfort, of ending the pain, of preventing infection, and nutritional balance. At the level of epidermic inflammation and phlyctena (skin blisters), the treatment may be completed by the use of growth factors. At the level of necrosis, after a temporary cover, an auto graft can be considered only if a healthy basis is guaranteed. The use of cellular cultures in order to obtain harmonious growth factors can be argued. (author)

[Combined burn trauma in the array of modern civilian and combat burns].

Science.gov (United States)

Ivchenko, E V; Borisov, D N; Golota, A S; Krassiĭ, A B; Rusev, I T

2015-02-01

The current article positions the combined burn and non-burn injuries in the general array of civilian and combat burns. For that purpose the official state statistics and scientific medical publications, domestic as well as foreign, have been analyzed. It has been shown that in peace time the combined burn/trauma injuries are infrequent. But the same type of injury becomes routine especially among the civilian population in the conditions of the modern so called "hybrid war". And the medical service should be prepared for it.

Burning mouth disorder

Directory of Open Access Journals (Sweden)

Anand Bala

2012-01-01

Full Text Available Burning mouth disorder (BMD is a burning or stinging sensation affecting the oral mucosa, lips and/or tongue, in the absence of clinically visible mucosal lesions. There is a strong female predilection, with the age of onset being approximately 50 years. Affected patients often present with multiple oral complaints, including burning, dryness and taste alterations. The causes of BMD are multifactorial and remain poorly understood. Recently, there has been a resurgence of interest in this disorder with the discovery that the pain of burning mouth syndrome (BMS may be neuropathic in origin and originate both centrally and peripherally. The most common sites of burning are the anterior tongue, anterior hard palate and lower lip, but the distribution of oral sites affected does not appear to affect the natural history of the disorder or the response to treatment BMS may persist for many years. This article provides updated information on BMS and presents a new model, based on taste dysfunction, for its pathogenesis.

Privacy encounters in Teledialogue

DEFF Research Database (Denmark)

Andersen, Lars Bo; Bøge, Ask Risom; Danholt, Peter

2017-01-01

Privacy is a major concern when new technologies are introduced between public authorities and private citizens. What is meant by privacy, however, is often unclear and contested. Accordingly, this article utilises grounded theory to study privacy empirically in the research and design project...... Teledialogue aimed at introducing new ways for public case managers and placed children to communicate through IT. The resulting argument is that privacy can be understood as an encounter, that is, as something that arises between implicated actors and entails some degree of friction and negotiation....... An argument which is further qualified through the philosophy of Gilles Deleuze. The article opens with a review of privacy literature before continuing to present privacy as an encounter with five different foci: what technologies bring into the encounter; who is related to privacy by implication; what...

Survival after burn in a sub-Saharan burn unit: Challenges and opportunities

Science.gov (United States)

Tyson, Anna F.; Boschini, Laura P.; Kiser, Michelle M.; Samuel, Jonathan C.; Mjuweni, Steven N.; Cairns, Bruce A.; Charles, Anthony G.

2013-01-01

Background Burns are among the most devastating of all injuries and a major global public health crisis, particularly in sub-Saharan Africa. In developed countries, aggressive management of burns continues to lower overall mortality and increase lethal total body surface area (TBSA) at which 50% of patients die (LA50). However, lack of resources and inadequate infrastructure significantly impede such improvements in developing countries. Methods This study is a retrospective analysis of patients admitted to the burn center at Kamuzu Central Hospital in Lilongwe, Malawi between June 2011 and December 2012. We collected information including patient age, gender, date of admission, mechanism of injury, time to presentation to hospital, total body surface area (TBSA) burn, comorbidities, date and type of operative procedures, date of discharge, length of hospital stay, and survival. We then performed bivariate analysis and logistic regression to identify characteristics associated with increased mortality. Results A total of 454 patients were admitted during the study period with a median age of 4 years (range 0.5 months to 79 years). Of these patients, 53% were male. The overall mean TBSA was 18.5%, and average TBSA increased with age—17% for 0–18 year olds, 24% for 19–60 year olds, and 41% for patients over 60 years old. Scald and flame burns were the commonest mechanisms, 52% and 41% respectively, and flame burns were associated with higher mortality. Overall survival in this population was 82%; however survival reduced with increasing age categories (84% in patients 0–18 years old, 79% in patients 19–60 years old, and 36% in patients older than 60 years). TBSA remained the strongest predictor of mortality after adjusting for age and mechanism of burn. The LA50 for this population was 39% TBSA. Discussion Our data reiterate that burn in Malawi is largely a pediatric disease and that the high burn mortality and relatively low LA50 have modestly improved

Children with burns referred for child abuse evaluation: Burn characteristics and co-existent injuries.

Science.gov (United States)

Pawlik, Marie-Christin; Kemp, Alison; Maguire, Sabine; Nuttall, Diane; Feldman, Kenneth W; Lindberg, Daniel M

2016-05-01

Intentional burns represent a serious form of physical abuse that must be identified to protect children from further harm. This study is a retrospectively planned secondary analysis of the Examining Siblings To Recognize Abuse (ExSTRA) network data. Our objective was to describe the characteristics of burns injuries in children referred to Child Abuse Pediatricians (CAPs) in relation to the perceived likelihood of abuse. We furthermore compare the extent of diagnostic investigations undertaken in children referred to CAPs for burn injuries with those referred for other reasons. Within this dataset, 7% (215/2890) of children had burns. Children with burns were older than children with other injuries (median age 20 months vs. 10 months). Physical abuse was perceived as likely in 40.9% (88) and unlikely in 59.1% (127). Scalds accounted for 52.6% (113) and contact burns for 27.6% (60). Several characteristics of the history and burn injury were associated with a significantly higher perceived likelihood of abuse, including children with reported inflicted injury, absent or inadequate explanation, hot water as agent, immersion scald, a bilateral/symmetric burn pattern, total body surface area ≥10%, full thickness burns, and co-existent injuries. The rates of diagnostic testing were significantly lower in children with burns than other injuries, yet the yield of skeletal survey and hepatic transaminases testing were comparable between the two groups. This would imply that children referred to CAPs for burns warrant the same level of comprehensive investigations as those referred for other reasons. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Technical problems encountered during certification of a Type B (plutonium) package (U)

International Nuclear Information System (INIS)

Gromada, R.J.; Opperman, E.K.

1993-01-01

Westinghouse Savannah River Company is responsible for maintaining the 5320 Plutonium Shipping Cask. The 5320 Cask was originally designed over 15 years ago to transport plutonium and americium. Since then the 5320 Cask has been redesigned numerous times to meet changing packaging regulations. During the current certificate renewal process, four of the 5320 Casks were subjected to hypothetical accident condition drop, puncture and thermal tests. This paper will discuss the technical problems encountered as well as the experiences gained from performing the accident test sequence. The first two sequential tests, the drop and puncture tests, were performed satisfactorily and immediately met the intent of the regulations. The third sequential test, a 1475degF thermal test, was performed in an electric furnace and did not meet regulations. Problems were encountered with oxygen deficiency and radiation attenuation during the test. An evaluation of the problems associated with furnace testing and their solutions will be discussed. The thermal test was repeated in a pool fire at the Sandia National Laboratory Lurance Canyon Burn Site. Unexpected problems from extremely high (1900degF) flame temperatures resulted in secondary vessel containment failure. From the results of a failure study, a heat shield was added to the 5320 Cask and a subsequent fire test determined that the packaging finally met the intent of the regulations. The failure study as well as the subsequent design solution will be discussed. (author)

Sodium

Science.gov (United States)

Table salt is a combination of two minerals - sodium and chloride Your body needs some sodium to work properly. It helps with the function ... in your body. Your kidneys control how much sodium is in your body. If you have too ...

Foot burns: epidemiology and management.

Science.gov (United States)

Hemington-Gorse, S; Pellard, S; Wilson-Jones, N; Potokar, T

2007-12-01

This is a retrospective study of the epidemiology and management of isolated foot burns presenting to the Welsh Centre for Burns from January 1998 to December 2002. A total of 289 were treated of which 233 were included in this study. Approximately 40% were in the paediatric age group and the gender distribution varied dramatically for adults and children. In the adult group the male:female ratio was 3.5:1, however in the paediatric group the male:female ratio was more equal (1.6:1). Scald burns (65%) formed the largest group in children and scald (35%) and chemical burns (32%) in adults. Foot burns have a complication rate of 18% and prolonged hospital stay. Complications include hypertrophic scarring, graft loss/delayed healing and wound infection. Although isolated foot burns represent a small body surface area, over half require treatment as in patients to allow for initial aggressive conservative management of elevation and regular wound cleansing to avoid complications. This study suggests a protocol for the initial acute management of foot burns. This protocol states immediate referral of all foot burns to a burn centre, admission of these burns for 24-48 h for elevation, regular wound cleansing with change of dressings and prophylactic antibiotics.

A Retrospective Analysis of the Burn Injury Patients Records in the Emergency Department, an Epidemiologic Study

Directory of Open Access Journals (Sweden)

Nilgün Aksoy

2014-08-01

Full Text Available Introduction: Burns can be very destructive, and severely endanger the health and lives of humans. It maybe cause disability and even psychological trauma in individuals. . Such an event can also lead to economic burden on victim’s families and society. The aim of our study is to evaluate epidemiology and outcome of burn patients referring to emergency department. Methods: This is a cross-sectional study was conducted by evaluation of patients’ files and forensic reports of burned patients’ referred to the emergency department (ED of Akdeniz hospital, Turkey, 2008. Demographic data, the season, place, reason, anatomical sites, total body surface area, degrees, proceeding treatment, and admission time were recorded. Multinomial logistic regression was used to compare frequencies’ differences among single categorized variables. Stepwise logistic regression was applied to develop a predictive model for hospitalization. P<0.05 was defined as a significant level. Results: Two hundred thirty patients were enrolled (53.9% female. The mean of patients' ages was 25.3 ± 22.3 years. The most prevalence of burn were in the 0-6 age group and most of which was hot liquid scalding (71.3%. The most affected parts of the body were the left and right upper extremities. With increasing the severity of triage level (OR=2.2; 95% CI: 1.02-4.66; p=0.046, intentional burn (OR=4.7; 95% CI: 1.03-21.8; p=0.047, referring from other hospitals or clinics (OR=3.4; 95% CI: 1.7-6.6; p=0.001, and percentage of burn (OR=18.1; 95% CI: 5.42-62.6; p<0.001 were independent predictive factor for hospitalization. In addition, odds of hospitalization was lower in patients older than 15 years (OR=0.7; 95% CI: 0.5-0.91; p=0.035. Conclusion: This study revealed the most frequent burns are encountered in the age group of 0-6 years, percentage of <10%, second degree, upper extremities, indoor, and scalding from hot liquids. Increasing ESI severity, intentional burn, referring from

Microbiological Monitoring and Proteolytic Study of Clinical Samples From Burned and Burned Wounded Patients

International Nuclear Information System (INIS)

Toema, M.A.; El-Bazza, Z.E.; El-Hifnawi, H.N.; Abd-El-Hakim, E.E.

2013-01-01

In this study, clinical samples were collected from 100 patients admitted to Burn and Plastic Surgery Department, Faculty of Medicine, Ain Shams University, Egypt, over a period of 12 months. The proteolytic activity of 110 clinical samples taken from surfaces swabs which taken from burned and burned wounded patients with different ages and gender was examined. Screening for the proteolytic activity produced by pathogenic bacteria isolated from burned and burned wounded patients was evaluated as gram positive Bacilli and gram negative bacilli showed high proteolytic activity (46.4%) while 17.9% showed no activity. The isolated bacteria proved to have proteolytic activity were classified into high, moderate and weak. The pathogenic bacteria isolated from burned and burned wounded patients and showing proteolytic activity were identified as Pseudomonas aeruginosa, Proteus mirabilis, Proteus vulgaris, Bacillus megaterium, Bacillus cereus, Staphylococcus aureus, Escherichia coli, Klebsiella ozaeanae, Klebsiella oxytoca, Klebsiella pneumoniae and Pseudomonas fluoresces.

Spatial frequency domain imaging of burn wounds in a preclinical model of graded burn severity

Science.gov (United States)

Nguyen, John Quan; Crouzet, Christian; Mai, Tuan; Riola, Kathleen; Uchitel, Daniel; Liaw, Lih-Huei; Bernal, Nicole; Ponticorvo, Adrien; Choi, Bernard; Durkin, Anthony J.

2013-06-01

Frequent monitoring of early-stage burns is necessary for deciding optimal treatment and management. Both superficial and full thickness burns are relatively easy to diagnose based on clinical observation. In between these two extremes are superficial-partial thickness and deep-partial thickness burns. These burns, while visually similar, differ dramatically in terms of clinical treatment and are known to progress in severity over time. The objective of this study was to determine the potential of spatial frequency domain imaging (SFDI) for noninvasively mapping quantitative changes in chromophore and optical properties that may be an indicative of burn wound severity. A controlled protocol of graded burn severity was developed and applied to 17 rats. SFDI data was acquired at multiple near-infrared wavelengths over a course of 3 h. Burn severity was verified using hematoxylin and eosin histology. From this study, we found that changes in water concentration (edema), deoxygenated hemoglobin concentration, and optical scattering (tissue denaturation) to be statistically significant at differentiating superficial partial-thickness burns from deep-partial thickness burns.

Epidemiology of burns throughout the World. Part II: intentional burns in adults.

Science.gov (United States)

Peck, Michael D

2012-08-01

A significant number of burns and deaths from fire are intentionally wrought. Rates of intentional burns are unevenly distributed throughout the world; India has a particularly high rate in young women whereas in Europe rates are higher in men in mid-life. Data from hospitalized burn patients worldwide reveal incidence rates for assault by fire and scalds ranging from 3% to 10%. The average proportion of the body surface area burned in an assault by fire or scalds is approximately 20%. In different parts of the world, attempted burning of others or oneself can be attributed to different motives. Circumstances under which assaults occur fall largely into the categories of interpersonal conflict, including spousal abuse, elder abuse, or interactions over contentious business transactions. Contributing social factors to assaults by burning include drug and alcohol abuse, non-constructive use of leisure time, non-participation in religious and community activities, unstable relationships, and extramarital affairs. Although the incidence of self-mutilation and suicide attempts by burning are relatively low, deliberate self-harm carries a significant risk of death, with an overall mortality rate of 65% worldwide. In those who resort to self-immolation, circumstantial themes reflect domestic discord, family dysfunction, and the social ramifications of unemployment. Preventing injurious burn-related violence requires a multifaceted approach, including legislation and enforcement, education, and advocacy. Better standardized assessment tools are needed to screen for risks of abuse and for psychiatric disorders in perpetrators. Copyright © 2012 Elsevier Ltd and ISBI. All rights reserved.

In-pile observation of gas release from sodium-joint carbide pins irradiated in Osiris

International Nuclear Information System (INIS)

Colin, M.; Faugere, J.L.; Rouault, J.

1978-01-01

Gas release is studied in three sodium-joint carbide pins irradiated in the reactor Osiris at a nominal linear power of 900 W/cm to burn-ups ranging from 4 to 13%. The overall activity, stable gases and radioactive gases are measured. It is found that most of the gas is released in busts, that the release of stable gases speeds up sharply after an incubation time, that the initial bursts are very large and that for each mode of release observed and for each class of nuclide the radioactive gases follow a law R/B=A/lambda.n. An attempt is made to interpret the results in terms of either the formation of gas bubbles in the sodium joint, the existence of a large bubble above the fissile column or the simultaneous release of a large number of smaller bubbles [fr

Burning mouth syndrome

OpenAIRE

K A Kamala; S Sankethguddad; S G Sujith; Praveena Tantradi

2016-01-01

Burning mouth syndrome (BMS) is multifactorial in origin which is typically characterized by burning and painful sensation in an oral cavity demonstrating clinically normal mucosa. Although the cause of BMS is not known, a complex association of biological and psychological factors has been identified, suggesting the existence of a multifactorial etiology. As the symptom of oral burning is seen in various pathological conditions, it is essential for a clinician to be aware of how to different...

Adult survivors' lived experience of burns and post-burn health: A qualitative analysis.

Science.gov (United States)

Abrams, Thereasa E; Ogletree, Roberta J; Ratnapradipa, Dhitinut; Neumeister, Michael W

2016-02-01

The individual implications of major burns are likely to affect the full spectrum of patients' physical, emotional, psychological, social, environmental, spiritual and vocational health. Yet, not all of the post-burn health implications are inevitably negative. Utilizing a qualitative approach, this heuristic phenomenological study explores the experiences and perceptions early (ages 18-35) and midlife (ages 36-64) adults providing insight for how participants perceived their burns in relationship to their post-burn health. Participants were interviewed using semi-structured interview questions framed around seven domains of health. Interview recordings were transcribed verbatim then coded line by line, identifying dominant categories related to health. Categories were analyzed identifying shared themes among the study sample. Participants were Caucasian, seven males and one female. Mean age at time of interviews was 54.38 and 42.38 at time of burns. Mean time since burns occurred was 9.38 years with a minimum of (20%) total body surface area (TBSA) burns. Qualitative content analysis rendered three emergent health-related categories and associated themes that represented shared meanings within the participant sample. The category of "Physical Health" reflected the theme physical limitations, pain and sensitivity to temperature. Within the category of "Intellectual Health" were themes of insight, goal setting and self-efficacy, optimism and humor and within "Emotional Health" were the themes empathy and gratitude. By exploring subjective experiences and perceptions of health shared through dialog with experienced burned persons, there are opportunities to develop a more complete picture of how holistic health may be affected by major burns that in turn could support future long-term rehabilitative trajectories of early and midlife adult burn patients. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Burn-related factors affecting anxiety, depression and self-esteem in burn patients: an exploratory study.

Science.gov (United States)

Jain, M; Khadilkar, N; De Sousa, A

2017-03-31

Burns are physically, psychologically and economically challenging injuries, and the factors leading to them are many and under-studied. The aim of the current study was to assess level of anxiety, depression and self-esteem in burn patients, and look at various burn-related variables that affect them. This cross-sectional study included 100 patients with burn injuries admitted to a tertiary care private hospital in an urban metropolis in India. The patients were assessed for anxiety, depression and self-esteem using the Hamilton anxiety rating scale, Hamilton depression rating scale and Rosenberg self-esteem scale respectively. Assessment was carried out within 2-8 weeks of injury following medical stabilization. The data was tabulated and statistically analyzed. The study sample was predominantly male (54%), married (69%), with a mean age of 34.1 ± 10.8 years. Accidental burns (94%) were the most common modality of injury. The majority (46%) suffered burns involving 20-59% total body surface area (TBSA), and facial burns were present (57%). No significant association was found between TBSA and anxiety, depression or self-esteem, and the same was true for facial burns. Deep burns, however, were significantly associated with anxiety (p=0.03) and depression (p=0.0002). High rates of anxiety and depression are associated with burn injuries and related to burn depth. Adjustment and recovery in these patients depends on various other factors like the patient's psychological status, nature/extent of the injury and ensuing medical care. Further research is warranted to reveal the magnitude and predictors of psychological problems in burn patients.

Treatment of Palm Burns in Children

OpenAIRE

Argirova, M.; Hadzhiyski, O.

2005-01-01

The timing and methods of treatment of palm burns in children vary widely. From January 2002 to November 2004, 492 children with burns - 125 of them with hand burns or other body burns - were hospitalized and treated at the N.I. Pirogov Clinic for Burns and Plastic Surgery in Bulgaria. Fifty-four children (for a total of 73 burned hands) presented isolated palm burns.Twenty-two hands were operated on. In this review we present the incidence, causes, treatment methods, functional results, and ...

Analysis of the minority actinides transmutation in a sodium fast reactor with uniform load pattern by the MCNPX-CINDER code

International Nuclear Information System (INIS)

Ochoa Valero, R.; Garcia-Herranz, N.; Aragones, J. M.

2010-01-01

The aim of this study is to evaluate the minority actinides transmutation in sodium fast reactors (SFR) assuming a uniform load pattern. It is determined the isotopic evolution of the actinides along burn, and the evolution of the reactivity and the reactivity coefficients. For that, it is used the MCNPX neutron transport code coupled with the inventory code CINDER90.

Etiology of Burn Injuries Among 0-6 Aged Children in One University Hospital Burn Unit, Bursa, Turkey

Directory of Open Access Journals (Sweden)

Neriman Akansel

2013-01-01

Full Text Available Background; Children whose verbal communications are not fully developed are the ones at risk for burn injuries. Causes of burn injuries vary among different age groups and scald injuries are the common cause of burn injuries among children. The majority of burns result from contact with thermal agents such as flame, hot surfaces, or hot liquids.Aim: The aim of this study was to determine etiologic factors of the burn injured children Methods: Data were collected for burn injured children treated in Uludag University Medical Hospital Burn Unit between January 2001 – December 2008. Patients’ demographic variables, etiology of burn injury, TBSA(total body surface area, degree of the burn injury, duration of hospitalization was detected from medical records of the hospitalized patients.Results: The mean age of the children was 2.5±1.5 (median=2. Although 4.6 % of burned patients were under one year of age, most of the children (67.8% were between 1-3 years. All of the patients were burned as a result of accident and house environment was the place where the burn incident occurred. Burn injuries occurredmostly during summer (29.9% and spring (28.7%. Scald injuries (75.3% were mostly seen burn injury types all among other burn injuries.Conclusions: Lack of supervision and observation are usually the most common causes of burn injuries in children. Statistical differences were found among age groups according to their burn etiology (p<0.05. An effect of TBSA on patient survival was statistically significant (p<0.000 and also statistically significant results were seen among age groups according to their TBSA’s (p<0.005.

Optimization of burn referrals

DEFF Research Database (Denmark)

Reiband, Hanna K; Lundin, Kira; Alsbjørn, Bjarne

2014-01-01

INTRODUCTION: Correct estimation of the severity of burns is important to obtain the right treatment of the patient and to avoid over- and undertriage. In this study we aimed to assess how often the guidelines for referral of burn injured patients are met at the national burn centre (NBC), Denmar...

Incidence and characteristics of chemical burns.

Science.gov (United States)

Koh, Dong-Hee; Lee, Sang-Gil; Kim, Hwan-Cheol

2017-05-01

Chemical burns can lead to serious health outcomes. Previous studies about chemical burns have been performed based on burn center data so these studies have provided limited information about the incidence of chemical burns at the national level. The aim of this study was to evaluate the incidence and characteristics of chemical burns using nationwide databases. A cohort representing the Korean population, which was established using a national health insurance database, and a nationwide workers' compensation database were used to evaluate the incidence and characteristics of chemical burns. Characteristics of the affected body region, depth of burns, industry, task, and causative agents were analyzed from two databases. The incidence of chemical burns was calculated according to employment status. The most common regions involving chemical burns with hospital visits were the skin followed by the eyes. For skin lesions, the hands and wrists were the most commonly affected regions. Second degree burns were the most common in terms of depth of skin lesions. The hospital visit incidence was 1.96 per 10,000 person-year in the general population. The compensated chemical burns incidence was 0.17 per 10,000 person-year. Employees and the self-employed showed a significantly increased risk of chemical burns undergoing hospital visits compared to their dependents. Chemical burns on the skin and eyes are almost equally prevalent. The working environment was associated with increased risk of chemical burns. Our results may aid in estimating the size of the problem and prioritizing prevention of chemical burns. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Sodium technology handbook

International Nuclear Information System (INIS)

2005-09-01

This document was published as a textbook for the education and training of personnel working for operations and maintenances of sodium facilities including FBR plants and those engaged in R and D activities related to sodium technology. This handbook covers the following technical areas. Properties of sodium. Compatibilities of sodium with materials. Thermalhydraulics and structural integrity. Sodium systems and components. Sodium instrumentations. Sodium handling technology. Sodium related accident evaluation and countermeasures for FBRs. Operation, maintenance and repair technology of sodium facilities. Safety measures related to sodium. Laws, regulations and internal rules related to sodium. The plannings and discussions of the handbook were made in the Sodium Technology Education Committee organized in O-arai Engineering Center consisting of the representatives of the related departments including Tsuruga headquarters. Experts in various departments participated in writing individual technical subjects. (author)

Encounters in cancer treatment

DEFF Research Database (Denmark)

Høybye, Mette Terp; Tjørnhøj-Thomsen, Tine

2014-01-01

Based on extensive ethnographic material from in-depth interviews with Danish cancer patients after treatment, this study analyzes their stories to explore how interactions with the physician configures and situates a need for rehabilitation. We identify three themes in the illness stories: (1...... by this encounter. The significance of the social encounters in cancer treatment is elucidated through this analysis, and we demonstrate how the need for recognition of the complex effects of cancer on one's life is central to counter experiences of objectification and dehumanization....

Astronaut observations of global biomass burning

International Nuclear Information System (INIS)

Wood, C.A.; Nelson, R.

1991-01-01

One of the most fundamental inputs for understanding and modeling possible effects of biomass burning is knowledge of the size of the area burned. Because the burns are often very large and occur on all continents (except Antarctica), observations from space are essential. Information is presented in this chapter on another method for monitoring biomass burning, including immediate and long-term effects. Examples of astronaut photography of burning during one year give a perspective of the widespread occurrence of burning and the variety of biological materials that are consumed. The growth of burning in the Amazon region is presented over 15 years using smoke as a proxy for actual burning. Possible climate effects of smoke palls are also discussed

[A tale of two encounters].

Science.gov (United States)

Chanel, Marie-Paule

The moving testimony of a patient shows the impact which a successful encounter can have. Beyond the positive clinical consequences, her rediscovered motivation and pleasure are the essential drivers which have guided her along the pathway of reconstruction. A tale of two encounters which have marked her life course. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Car radiator burns: a prevention issue.

Science.gov (United States)

Rabbitts, Angela; Alden, Nicole E; Conlin, Tara; Yurt, Roger W

2004-01-01

Scald burns continue to be the major cause of injury to patients admitted to the burn center. Scald burns occurring from car radiator fluid comprise a significant subgroup. Although manufacturer warning labels have been placed on car radiators, these burns continue to occur. This retrospective review looks at all patients admitted to our burn center who suffered scald burns from car radiator fluid to assess the extent of this problem. During the study period, 86 patients were identified as having suffered scald burns as a result of contact with car radiator fluid. Seventy-one percent of the burn injuries occurred in the summer months. The areas most commonly burned were the head and upper extremities. Burn prevention efforts have improved greatly over the years; however, this study demonstrates that scald burns from car radiator fluid continue to cause physical, emotional, and financial devastation. The current radiator warning labels alone are not effective. The National Highway Traffic Safety Administration has proposed a new federal motor vehicle safety standard to aid in decreasing the number of scald burns from car radiators. The results of this study were submitted to the United States Department of Transportation for inclusion in a docket for federal legislation supporting these safety measures.

Innovation from the ICT-based service encounter

DEFF Research Database (Denmark)

Henten, Anders

2012-01-01

The pupose of the paper is to develop a framework for analyzing the dynamics of innovations emanating from the ICT-based service encounters. Many innovations are based on the direct encounter between employees and customers, and the paper aims to extend the analysis of such encounters to ICT...

Characterization of a sodium-cooled fast reactor in an MHR-SFR synergy for TRU transmutation

International Nuclear Information System (INIS)

Hong, Ser Gi; Kim, Yonghee; Venneri, Francesco

2008-01-01

In the task of destroying the light water reactor (LWR) transuranics (TRUs), we consider the concept of a synergistic combination of a deep-burn (DB) gas-cooled reactor followed by a sodium-cooled fast reactor (SFR), as an alternative way to the direct feeding of the LWR TRUs to the SFR. In the synergy concept, TRUs from LWR are first deeply incinerated in a graphite-moderated DB-MHR (modular helium reactor) and then the spent fuels of DB-MHR are recycled into the closed-cycle SFR. The DB-MHR core is 100% TRU-loaded and a deep-burning (50-65%) is achieved in a safe manner (as discussed in our previous work). In this analysis, the SFR fuel cycle is closed with a pyro-processing technology to minimize the waste stream to a final repository. Neutronic characteristics of the SFR core in the MHR-SFR synergy have been evaluated from the core physics point of view. Also, we have compared core characteristics of the synergy SFR with those of a stand-alone SFR transuranic burner. For a consistent comparison, the two SFRs are designed to have the same TRU consumption rate of ∼250 kg/GW EFPY that corresponds to the TRU discharge rate from three 600 MW DB-MHRs. The results of our work show that the synergy SFR, fed with TRUs from DB-MHR, has a much smaller burnup reactivity swing, a slightly greater delayed neutron fraction (both positive features) but also a higher sodium void worth and a less negative Doppler coefficients than the conventional SFR, fed with TRUs directly from the LWRs. In addition, several design measures have been considered to reduce the sodium void worth in the synergy SFR core

Oral Rehydration Therapy in Burn Patients

Science.gov (United States)

2014-04-24

Burn Any Degree Involving 20-29 Percent of Body Surface; Burn Any Degree Involving 30-39 Percent of Body Surface; Burn Any Degree Involving 40-49 Percent of Body Surface; Burn Any Degree Involving 50-59 Percent of Body Surface; Burn Any Degree Involving 60-65 Percent of Body Surface

ASRS Reports on Wake Vortex Encounters

Science.gov (United States)

Connell, Linda J.; Taube, Elisa Ann; Drew, Charles Robert; Barclay, Tommy Earl

2010-01-01

ASRS is conducting a structured callback research project of wake vortex incidents reported to the ASRS at all US airports, as well as wake encounters in the enroute environment. This study has three objectives: (1) Utilize the established ASRS supplemental data collection methodology and provide ongoing analysis of wake vortex encounter reports; (2) Document event dynamics and contributing factors underlying wake vortex encounter events; and (3) Support ongoing FAA efforts to address pre-emptive wake vortex risk reduction by utilizing ASRS reporting contributions.

Initial Encounters : The Lived Experiences of Buyers

NARCIS (Netherlands)

G. Wright; J.J. Dekker

2012-01-01

The initial encounter between a buyer and a seller has received much attention among practitioners. The first time a buyer interacts with a seller is thought to be highly influential. The premise is that buyers form an opinion during this first encounter, or even the first minutes of this encounter.

Applicability of RELAP5-3D for Thermal-Hydraulic Analyses of a Sodium-Cooled Actinide Burner Test Reactor

Energy Technology Data Exchange (ETDEWEB)

C. B. Davis

2006-07-01

The Actinide Burner Test Reactor (ABTR) is envisioned as a sodium-cooled, fast reactor that will burn the actinides generated in light water reactors to reduce nuclear waste and ease proliferation concerns. The RELAP5-3D computer code is being considered as the thermal-hydraulic system code to support the development of the ABTR. An evaluation was performed to determine the applicability of RELAP5-3D for the analysis of a sodium-cooled fast reactor. The applicability evaluation consisted of several steps, including identifying the important transients and phenomena expected in the ABTR, identifying the models and correlations that affect the code’s calculation of the important phenomena, and evaluating the applicability of the important models and correlations for calculating the important phenomena expected in the ABTR. The applicability evaluation identified code improvements and additional models needed to simulate the ABTR. The accuracy of the calculated thermodynamic and transport properties for sodium was also evaluated.

Inhibitin: a specific inhibitor of sodium/sodium exchange in erythrocytes.

OpenAIRE

Morgan, K; Brown, R C; Spurlock, G; Southgate, K; Mir, M A

1986-01-01

An inhibitor of ouabain-insensitive sodium/sodium exchange in erythrocytes has been isolated from leukemic promyelocytes. To explore the specific effects of this inhibitor, named inhibitin, sodium transport experiments were carried out in human erythrocytes. Inhibitin reduced ouabain-insensitive bidirectional sodium transport. It did not change net sodium fluxes, had no significant effect on rubidium influx, and did not inhibit sodium-potassium-ATPase activity. The inhibitory effect of inhibi...

Electrochemical machining of burn-resistant Ti40 alloy

Directory of Open Access Journals (Sweden)

Xu Zhengyang

2015-08-01

Full Text Available This study investigates the feasibility of using electrochemical machining (ECM to produce critical aeroengine components from a new burn-resistant titanium alloy (Ti40, thereby reducing costs and improving efficiency relative to conventional mechanical machining. Through this, it is found that an aqueous mix of sodium chloride and potassium bromide provides the optimal electrolyte and that the surface quality of the Ti40 workpiece is improved by using a pulsed current of 1 kHz rather than a direct current. Furthermore, the quality of cavities produced by ECM and the overall material removal rate are determined to be dependent on a combination of operating voltage, electrolyte inlet pressure, cathode feeding rate and electrolyte concentration. By optimizing these parameters, a surface roughness of 0.371 μm has been achieved in conjunction with a specific removal rate of more than 3.1 mm3/A·min.

Treatment of secondary burn wound progression in contact burns-a systematic review of experimental approaches.

Science.gov (United States)

Schmauss, Daniel; Rezaeian, Farid; Finck, Tom; Machens, Hans-Guenther; Wettstein, Reto; Harder, Yves

2015-01-01

After a burn injury, superficial partial-thickness burn wounds may progress to deep partial-thickness or full-thickness burn wounds, if kept untreated. This phenomenon is called secondary burn wound progression or conversion. Burn wound depth is an important determinant of patient morbidity and mortality. Therefore, reduction or even the prevention of secondary burn wound progression is one goal of the acute care of burned patients. The objective of this study was to review preclinical approaches evaluating therapies to reduce burn wound progression. A systematic review of experimental approaches in animals that aim at reducing or preventing secondary burn wound progression was performed in accordance with the Preferred Reporting Items for Systematic Reviews and Meta Analysis (PRISMA) guidelines. The selected references consist of all the peer-reviewed studies performed in vivo in animals and review articles published in English, German, Italian, Spanish, or French language relevant to the topic of secondary burn wound progression. We searched MEDLINE, Cochrane Library, and Google Scholar including all the articles published from the beginning of notations to the present. The search was conducted between May 3, 2012 and December 26, 2013. We included 29 experimental studies in this review, investigating agents that maintain or increase local perfusion conditions, as well as agents that exhibit an anti-coagulatory, an anti-inflammatory, or an anti-apoptotic property. Warm water, simvastatin, EPO, or cerium nitrate may represent particularly promising approaches for the translation into clinical use in the near future. This review demonstrates promising experimental approaches that might reduce secondary burn wound progression. Nevertheless, a translation into clinical application needs to confirm the results compiled in experimental animal studies.

IAEA NAPRO coordinated research project: physical properties of sodium - 15331

International Nuclear Information System (INIS)

Passerini, S.; Gerardi, C.; Grandy, C.; Azpitarte, O.E.; Chocron, M.; Japas, M.L.; Bubelis, E.; Perez-Martin, S.; Jayaraj, S.; Roelofs, F.; Latge, C.; Gerschenfeld, A.; Long, Bin; Selvaraj, P.; Marinenko, E.; Zagorulko, Y.; Ohira, H.; Monti, S.

2015-01-01

The International Atomic Energy Agency (IAEA) recently established a CRP on 'Sodium properties and safe operation of experimental facilities in support of the development and deployment of Sodium Cooled Fast Reactors - NAPRO', to be carried out in the period 2013-2017. The first phase of the CRP is focused on the collection and assessment of sodium properties, and it will lead to a consistent property data set which will be published in the form of a handbook. This work is carried out by the 11 participating organizations from 10 Member States through the review and evaluation of the existing available data, the identification of the data gaps and the development of recommendations for experimental programmes to support closing these data gaps. A specific work package (WP 1.1), under the leadership of Argonne National Laboratory, is focused on the analysis of physical properties of sodium: 19 thermodynamic properties (including gaseous state) and 12 transport properties. The expected outcome includes the improved understanding of the availability, accuracy and range of applications of sodium properties centered on fast reactors and other technological applications. The implemented methodology for WP 1.1 (including the division of work among participants and an overall overview of the collected references) is described and so the properties included in WP 1.1 and their classification. Major findings to date related to WP 1.1 are presented in this work, including detailed analysis of two selected properties. The availability of relevant data in principal and out-of-principal references is discussed. Finally, challenges encountered with the collection of references, uncertainty and lack of recent experimental investigation are also listed and adjustments to the methodological approach are proposed as future work. (authors)

Sodium Exposure Tests on Limestone Concrete Used as Sacrificial Protection Layer in FBR

International Nuclear Information System (INIS)

Parida, F.C.; Das, S.K.; Sharma, A.K.; Rao, P.M.; Ramesh, S.S.; Somayajulu, P.A.; Malarvizhi, B.; Kasinathan, N.

2006-01-01

Hot sodium coming in contact with structural concrete in case of sodium leak in FBR system cause damage as a result of thermo-chemical attack by burning sodium. In addition, release of free and bound water from concrete leads to generation of hydrogen gas, which is explosive in nature. Hence limestone concrete, as sacrificial layer on the structural concrete in FBR, needs to be qualified. Four concrete blocks of dimension 600 mm x 600 mm x 300 mm with 300 mm x 300 mm x 150 mm cavity were cast and subjected to controlled sodium exposure tests. They have composition of ordinary portland cement, water, fine and coarse aggregate of limestone in the ratio of 1: 0.58: 2.547: 3.817. These blocks were subjected to preliminary inspection by ultrasonic pulse velocity technique and rebound hammer tests. Each block was exposed for 30 minutes to about 12 kg of liquid sodium (∼ 120 mm liquid column) at 550 deg. C in open air, after which sodium was sucked back from the cavity of the concrete block into a sodium tank. On-line temperature monitoring was carried out at strategic locations of sodium pool and concrete block. After removing sodium from the cavity and cleaning the surfaces, rebound hammer testing was carried out on each concrete block at the same locations where data were taken earlier at pre-exposed stage. The statistical analysis of rebound hammer data revealed that one of the concrete block alone has undergone damage to the extent of 16%. The loss of mass occurred for all the four blocks varied from 0.6 to 2.4% due to release of water during the test duration. Chemical analysis of sodium in concrete samples collected from cavity floor of each block helped in generation of depth profiles of sodium monoxide concentration for each block. From this it is concluded that a bulk penetration of sodium up to 30 mm depth has taken place. However it was also observed that at few local spots, sodium penetrated into concrete up to 50 mm. Cylindrical core samples of 50 mm x 150

The space of togetherness--a caring encounter.

Science.gov (United States)

Holopainen, Gunilla; Kasén, Anne; Nyström, Lisbet

2014-03-01

Encounters in relation to the nurse-patient relationship are often discussed within nursing and caring literature without a reflection on the actual meaning of the concept. Assuming that an encounter is essential for nursing care, this article seeks to create a deeper understanding of the concept through a hermeneutic approach to texts by the philosophers Buber and Marcel. Presence, recognition, availability and mutuality seem to be essential prerequisites for an encounter. As these prerequisites are fulfilled within and between human beings who encounter each other, it is possible to speak of a space of togetherness, a mutual existence, where life's mystery shines forth and caring is realized. The challenge lies in creating these encounters within nursing care. © 2012 The Authors Scandinavian Journal of Caring Sciences © 2012 Nordic College of Caring Science.

In-situ burning: NIST studies

International Nuclear Information System (INIS)

Evans, D.D.

1992-01-01

In-situ burning of spilled oil has distinct advantages over other countermeasures. It offers the potential to convert rapidly large quantities of oil into its primary combustion products, carbon dioxide and water, with a small percentage of other unburned and residue byproducts. Because the oil is converted to gaseous products of combustion by burning, the need for physical collection, storage, and transport of recovered fluids is reduced to the few percent of the original spill volume that remains as residue after burning. Burning oil spills produces a visible smoke plume containing smoke particulate and other products of combustion which may persist for many kilometers from the burn. This fact gives rise to public health concerns, related to the chemical content of the smoke plume and the downwind deposition of particulate, which need to be answered. In 1985, a joint Minerals Management Service (MMS) and Environment Canada (EC) in-situ burning research program was begun at the National Institute of Standards and Technology (NIST). This research program was designed to study the burning of large crude oil spills on water and how this burning would affect air quality by quantifying the products of combustion and developing methods to predict the downwind smoke particulate deposition. To understand the important features of in-situ burning, it is necessary to perform both laboratory and mesoscale experiments. Finally, actual burns of spilled oil at sea will be necessary to evaluate the method at the anticipated scale of actual response operations. In this research program there is a continuing interaction between findings from measurements on small fire experiments performed in the controlled laboratory environments of NIST and the Fire Research Institute (FRI) in Japan, and large fire experiments at facilities like the USCG Fire Safety and Test Detachment in Mobile, Alabama where outdoor liquid fuel burns in large pans are possible

Reliability enhancement through optimal burn-in

Science.gov (United States)

Kuo, W.

1984-06-01

A numerical reliability and cost model is defined for production line burn-in tests of electronic components. The necessity of burn-in is governed by upper and lower bounds: burn-in is mandatory for operation-critical or nonreparable component; no burn-in is needed when failure effects are insignificant or easily repairable. The model considers electronic systems in terms of a series of components connected by a single black box. The infant mortality rate is described with a Weibull distribution. Performance reaches a steady state after burn-in, and the cost of burn-in is a linear function for each component. A minimum cost is calculated among the costs and total time of burn-in, shop repair, and field repair, with attention given to possible losses in future sales from inadequate burn-in testing.

Phoenix Society for Burn Survivors

Science.gov (United States)

... in 2018! Learn More For Loved Ones A burn injury doesn't just impact the survivor. Families ... to support longterm recovery, improve the quality of burn care, and prevent burn injury. Explore articles on ...

Simple method of determining induced 32P activity following burning of sulfur tablets by measuring Cherenkov radiation

International Nuclear Information System (INIS)

Kubicek, I.

1986-01-01

A method is described allowing the detemination of induced beta activity of phosphorus-32 using Cherenkov radiation, following the burning of sulfur tablets in the measuring vesels. A mixture of phosphoric acid and sodium phosphate solutions was used as the medium for the production of Cherenkov radiation. The losses of activity during sulfur tablet burning, the detection efficiency and the minimum detectable activity for which the minimum determinable dose was estimated, were determined. The results obtained by measurement with Cherenkov radiation are compared with other techniques of phosphorus-32 detection. The method was tested at VUPL Bratislava on detectors irradited using a 252 Cf fast neutron source. From Caswell's data, the fluence-to-kerma conversin factor was determined for a neutron spectrum calculated by the Monte Carlo method. Tissue kerma was estimated from the neutron fluence corresponding to the appropriate values of saturated activity per 1 sulfur-32 nucleus. (author)

Ultrasound assessed thickness of burn scars in association with laser Doppler imaging determined depth of burns in paediatric patients.

Science.gov (United States)

Wang, Xue-Qing; Mill, Julie; Kravchuk, Olena; Kimble, Roy M

2010-12-01

This study describes the ultrasound assessment of burn scars in paediatric patients and the association of these scar thickness with laser Doppler imaging (LDI) determined burn depth. A total of 60 ultrasound scar assessments were conducted on 33 scars from 21 paediatric burn patients at 3, 6 and 9 months after-burn. The mean of peak scar thickness was 0.39±0.032 cm, with the thickest at 6 months (0.40±0.036 cm). There were 17 scald burn scars (0.34±0.045 cm), 4 contact burn scars (0.61±0.092 cm), and 10 flame burn scars (0.42±0.058 cm). Each group of scars followed normal distributions. Twenty-three scars had original burns successfully scanned by LDI and various depths of burns were presented by different colours according to blood perfusion units (PU), with dark blue burns, with the thinnest scars for green coloured burns and the thickest for dark blue coloured burns. Within light blue burns, grafted burns healed with significantly thinner scars than non-grafted burns. This study indicates that LDI can be used for predicting the risk of hypertrophic scarring and for guiding burn care. To our knowledge, this is the first study to correlate the thickness of burns scars by ultrasound scan with burn depth determined by LDI. Copyright © 2010 Elsevier Ltd and ISBI. All rights reserved.

Impact of nuclear data on sodium-cooled fast reactor calculations

International Nuclear Information System (INIS)

Aures, A.; Bostelmann, F.; Zwermann, W.; Velkov, K.

2016-01-01

Neutron transport and depletion calculations are performed in combination with various nuclear data libraries in order to assess the impact of nuclear data on safety-relevant parameters of sodium-cooled fast reactors. These calculations are supplemented by systematic uncertainty analyses with respect to nuclear data. Analysed quantities are the multiplication factor and nuclide densities as a function of burn-up and the Doppler and Na-void reactivity coefficients at begin of cycle. While ENDF/B-VII.0 / -VII.1 yield rather consistent results, larger discrepancies are observed between the JEFF libraries. While the newest evaluation, JEFF-3.2, agrees with the ENDF/B-VII libraries, the JEFF-3.1.2 library yields significant larger multiplication factors. (authors)

Is location of burns related to outcome? A comparison between burns on extremities and burns on head and/or trunk in patients with low to intermediate TBSA in a burn center in The Netherlands.

Science.gov (United States)

Menger, Tirsa; Krijnen, Pieta; Tuinebreijer, Willem E; Breederveld, Roelf S

2014-01-01

In the literature no study was found about the effect of location of burns on outcome. The objective of this retrospective study was to investigate the effect of location on outcome parameters of 371 patients, admitted to our burn center from January 2009 to December 2011. The patients were included in the study if more than 80% of the burn(s) was localized either on the extremities or on the head and/or trunk. Two groups of TBSA were elaborated, low: 0 to 5% and intermediate: 5 to 15%. Two-hundred ninety-two patients (78.7%) had a low TBSA (burns on the head and/or trunk were more often admitted to the intensive care unit, mostly as a result of suspected inhalation injury (6.2 vs 0.9%; P = .008). More complications were seen in the intermediate TBSA group. In this study no difference in outcome was found between burns on the head and/or trunk or on extremities. The patients with burns on the head and/or trunk group are more frequently admitted to intensive care.

Burn Wise Educational Materials for Businesses

Science.gov (United States)

Burn Wise outreach material. Burn Wise is a partnership program of that emphasizes the importance of burning the right wood, the right way, in the right wood-burning appliance to protect your home, health, and the air we breathe.

The treatment of extensively burned patents and β irradiational injury skin burn patients with irradiated pigskin

International Nuclear Information System (INIS)

Tang Zhongyi; Lu Xingan; Jing Ling; Qi Qiang

1994-01-01

Obvious therapeutic effects achieved by the covering of irradiation sterilized pigskin on burn wounds, escarectomized 3rd degree burn wounds β injured burns are discussed. The article also describes the manufacture processes of irradiated pigskins and the selection of surgical treatments of various burns. 5 refs., 1 tab., 4 figs

Assault by burning in Jordan

Science.gov (United States)

Haddadin, W.

2012-01-01

Summary Criminal attacks by burns on women in Jordan are highlighted in this retrospective study carried out of all proved cases of criminal burns in female patients treated at the burn unit of the Royal Rehabilitation Center in Jordan between January 2005 and June 2012. Thirteen patients were included in our study, out of a total of 550 patients admitted, all in the age range of 16-45 yr. Of these 13 women, six were burned by acid throwing, five by hot water, and two by direct flames from fuel thrown over them. Burn percentage ranged from 15 to 75% of the total body surface area, with involvement in most cases of the face and upper trunk. The mean hospital stay was 33 days and the mortality rate was 3/13, i.e. 23%. Violence against women exists in Jordanian society, yet burning assaults are rare. Of these, burning by throwing acid is the most common and most disfiguring act, with a higher mortality rate in domestic environments. PMID:23766757

Adiabatic flame temperature of sodium combustion and sodium-water reaction

International Nuclear Information System (INIS)

Okano, Y.; Yamaguchi, A.

2001-01-01

In this paper, background information of sodium fire and sodium-water reaction accidents of LMFBR (liquid metal fast breeder reactor) is mentioned at first. Next, numerical analysis method of GENESYS is described in detail. Next, adiabatic flame temperature and composition of sodium combustion are analyzed, and affect of reactant composition, such oxygen and moisture, is discussed. Finally, adiabatic reaction zone temperature and composition of sodium-water reaction are calculated, and affects of reactant composition, sodium vaporization, and pressure are stated. Chemical equilibrium calculation program for generic chemical system (GENESYS) is developed in this study for the research on adiabatic flame temperature of sodium combustion and adiabatic reaction zone temperature of sodium-water reaction. The maximum flame temperature of the sodium combustion is 1,950 K at the standard atmospheric condition, and is not affected by the existence of moisture. The main reaction product is Na 2 O (l) , and in combustion in moist air, with NaOH (g) . The maximum reaction zone temperature of the sodium-water reaction is 1,600 K, and increases with the system pressure. The main products are NaOH (g) , NaOH (l) and H2 (g) . Sodium evaporation should be considered in the cases of sodium-rich and high pressure above 10 bar

Sodium in diet

Science.gov (United States)

Diet - sodium (salt); Hyponatremia - sodium in diet; Hypernatremia - sodium in diet; Heart failure - sodium in diet ... Too much sodium in the diet may lead to: High blood pressure in some people A serious buildup of fluid in people with heart failure , cirrhosis of ...

Silicon Burning. II. Quasi-Equilibrium and Explosive Burning

International Nuclear Information System (INIS)

Hix, W.R.; Thielemann, F.

1999-01-01

Having examined the application of quasi-equilibrium to hydrostatic silicon burning in Paper I of this series, we now turn our attention to explosive silicon burning. Previous authors have shown that for material that is heated to high temperature by a passing shock and then cooled by adiabatic expansion, the results can be divided into three broad categories, incomplete burning, normal freezeout, and α-rich freezeout, with the outcome depending on the temperature, density, and cooling timescale. In all three cases, we find that the important abundances obey quasi-equilibrium for temperatures greater than approximately 3x10 9 K, with relatively little nucleosynthesis occurring following the breakdown of quasi-equilibrium. We will show that quasi-equilibrium provides better abundance estimates than global nuclear statistical equilibrium, even for normal freezeout, and particularly for α-rich freezeout. We will also examine the accuracy with which the final nuclear abundances can be estimated from quasi-equilibrium. copyright copyright 1999. The American Astronomical Society

Creep and creep rupture properties of cladding tube (type 316) in high temperature sodium

International Nuclear Information System (INIS)

Atsumo, H.

1977-01-01

The thin walled small sized seamless AISI 316 steel tubes, which are designated to be domestically used as the fuel cladding tube for sodium cooled fast breeder reactors in Japan, are irradiated in the following sodium of high temperature in the range of 370 deg. C to 700 deg. C, and receive gradually increased internal pressure caused by the fission produced gas generating from the nuclear fuel burn-up inside the cladding tube. Consequently, the creep behavior of fuel cladding tubes under a high temperature sodium environment is an important problem which must be determined and clarified together with their characteristic features under irradiation and in air. In relation to the creep performance of fuel cladding tubes made of AISI 316 steel and other comparable austenitic stainless steels, hardly any studies are found that are made systematically to examine the effect of sodium with sodium purity as parameter or any comparative studies with in-air data at various different temperatures. The present research work was aimed to obtain certain basic design data relating to in-sodium creep performance of the domestic made fuel cladding tubes for fast breeder reactors, and also to gain further date as considered necessary under several sodium conditions. That is, together with establishment of the technology for tensile creep test and internal pressure creep rupture test in flowing sodium of high temperature, a series of tests and studies were performed on the trial made cladding tubes of AISI Type-316 steel. In the first place, two kinds of purity conditions of sodium, close to the actual reactor-operating condition, (oxygen concentration of 10 ppm and 5 ppm respectively) were established, and then uniaxial tensile creep test and rupture test under various temperatures were performed and the resulting data were compared and evaluated against the in-air data. Then, secondly, an internal pressure creep rupture test was conducted under a single purity sodium environment

Methylated spirit burns: an ongoing problem.

Science.gov (United States)

Jansbeken, J R H; Vloemans, A F P M; Tempelman, F R H; Breederveld, R S

2012-09-01

Despite many educational campaigns we still see burns caused by methylated spirit every year. We undertook a retrospective study to analyse the impact of this problem. We retrospectively collected data of all patients with burns caused by methylated spirit over twelve years from 1996 to 2008. Our main endpoints were: incidence, age, mechanism of injury, total body surface area (TBSA) burned, burn depth, need for surgery and length of hospital stay. Ninety-seven patients with methylated spirit burns were included. During the study period there was no decrease in the number of patients annually admitted to the burn unit with methylated spirit burns. 28% of the patients (n=27) were younger than eighteen years old, 15% (n=15) were ten years old or younger. The most common cause of burns was carelessness in activities involving barbecues, campfires and fondues. Mean TBSA burned was 16% (SD 12.4). 70% (n=68) had full thickness burns. 66% (n=64) needed grafting. Mean length of hospital stay was 23 days (SD 24.7). The use of methylated spirit is an ongoing problem, which continues to cause severe burns in adults and children. Therefore methylated spirit should be banned in households. We suggest sale only in specialised shops, clear labelling and mandatory warnings. Copyright © 2012 Elsevier Ltd and ISBI. All rights reserved.

In situ Microscopic Observation of Sodium Deposition/Dissolution on Sodium Electrode

OpenAIRE

Yuhki Yui; Masahiko Hayashi; Jiro Nakamura

2016-01-01

Electrochemical sodium deposition/dissolution behaviors in propylene carbonate-based electrolyte solution were observed by means of in situ light microscopy. First, granular sodium was deposited at pits in a sodium electrode in the cathodic process. Then, the sodium particles grew linearly from the electrode surface, becoming needle-like in shape. In the subsequent anodic process, the sodium dissolved near the base of the needles on the sodium electrode and the so-called ?dead sodium? broke a...

The impact of antecedent fire area on burned area in southern California coastal ecosystems

Science.gov (United States)

Price, Owen F.; Bradstock, Ross A.; Keeley, Jon E.; Syphard, Alexandra D.

2012-01-01

Frequent wildfire disasters in southern California highlight the need for risk reduction strategies for the region, of which fuel reduction via prescribed burning is one option. However, there is no consensus about the effectiveness of prescribed fire in reducing the area of wildfire. Here, we use 29 years of historical fire mapping to quantify the relationship between annual wildfire area and antecedent fire area in predominantly shrub and grassland fuels in seven southern California counties, controlling for annual variation in weather patterns. This method has been used elsewhere to measure leverage: the reduction in wildfire area resulting from one unit of prescribed fire treatment. We found little evidence for a leverage effect (leverage = zero). Specifically our results showed no evidence that wildfire area was negatively influenced by previous fires, and only weak relationships with weather variables rainfall and Santa Ana wind occurrences, which were variables included to control for inter-annual variation. We conclude that this is because only 2% of the vegetation burns each year and so wildfires rarely encounter burned patches and chaparral shrublands can carry a fire within 1 or 2 years after previous fire. Prescribed burning is unlikely to have much influence on fire regimes in this area, though targeted treatment at the urban interface may be effective at providing defensible space for protecting assets. These results fit an emerging global model of fire leverage which position California at the bottom end of a continuum, with tropical savannas at the top (leverage = 1: direct replacement of wildfire by prescribed fire) and Australian eucalypt forests in the middle (leverage ∼ 0.25).

Burns (For Parents)

Science.gov (United States)

... small, and have sensitive skin that needs extra protection. Although some minor burns aren't cause for concern and can ... burns, the mildest of the three, are limited to the top layer of skin: Signs ... pain, and minor swelling. The skin is dry without blisters. Healing ...

Beyond the Embodied Digital Service Encounter

DEFF Research Database (Denmark)

Sørensen, Jannick Kirk

2018-01-01

When a digital service encounter develops differently than anticipated, the client becomes a user. This transformation reveals the ambiguous nature of digital service encounter being neither well-functioning tools, nor having the same sensitivity to and tolerance for service failures as in human ...

Smartphone applications in burns.

Science.gov (United States)

Wurzer, Paul; Parvizi, Daryousch; Lumenta, David B; Giretzlehner, Michael; Branski, Ludwik K; Finnerty, Celeste C; Herndon, David N; Tuca, Alexandru; Rappl, Thomas; Smolle, Christian; Kamolz, Lars P

2015-08-01

Since the introduction of applications (apps) for smartphones, the popularity of medical apps has been rising. The aim of this review was to demonstrate the current availability of apps related to burns on Google's Android and Apple's iOS store as well as to include a review of their developers, features, and costs. A systematic online review of Google Play Store and Apple's App Store was performed by using the following search terms: "burn," "burns," "thermal," and the German word "Verbrennung." All apps that were programmed for use as medical apps for burns were included. The review was performed from 25 February until 1 March 2014. A closer look at the free and paid calculation apps including a standardized patient was performed. Four types of apps were identified: calculators, information apps, book/journal apps, and games. In Google Play Store, 31 apps were related to burns, of which 20 were calculation apps (eight for estimating the total body surface area (TBSA) and nine for total fluid requirement (TFR)). In Apple's App Store, under the category of medicine, 39 apps were related to burns, of which 21 were calculation apps (19 for estimating the TBSA and 17 for calculating the TFR). In 19 out of 32 available calculation apps, our study showed a correlation of the calculated TFR compared to our standardized patient. The review demonstrated that many apps for medical burns are available in both common app stores. Even free available calculation apps may provide a more objective and reproducible procedure compared to manual/subjective estimations, although there is still a lack of data security especially in personal data entered in calculation apps. Further clinical studies including smartphone apps for burns should be performed. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Towards more efficient burn care: Identifying factors associated with good quality of life post-burn.

Science.gov (United States)

Finlay, V; Phillips, M; Allison, G T; Wood, F M; Ching, D; Wicaksono, D; Plowman, S; Hendrie, D; Edgar, D W

2015-11-01

As minor burn patients constitute the vast majority of a developed nation case-mix, streamlining care for this group can promote efficiency from a service-wide perspective. This study tested the hypothesis that a predictive nomogram model that estimates likelihood of good long-term quality of life (QoL) post-burn is a valid way to optimise patient selection and risk management when applying a streamlined model of care. A sample of 224 burn patients managed by the Burn Service of Western Australia who provided both short and long-term outcomes was used to estimate the probability of achieving a good QoL defined as 150 out of a possible 160 points on the Burn Specific Health Scale-Brief (BSHS-B) at least six months from injury. A multivariate logistic regression analysis produced a predictive model provisioned as a nomogram for clinical application. A second, independent cohort of consecutive patients (n=106) was used to validate the predictive merit of the nomogram. Male gender (p=0.02), conservative management (p=0.03), upper limb burn (p=0.04) and high BSHS-B score within one month of burn (pburns were excluded due to loss to follow up. For clinicians managing comparable burn populations, the BSWA burns nomogram is an effective tool to assist the selection of patients to a streamlined care pathway with the aim of improving efficiency of service delivery. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

The sodium coolant

International Nuclear Information System (INIS)

Rodriguez, G.

2004-01-01

The sodium is the best appropriate coolant for the fast neutrons reactors technology. Thus the fast neutrons reactors development is intimately bound to the sodium technology. This document presents the sodium as a coolant point of view: atomic structure and characteristics, sodium impacts on the fast neutron reactors technology, chemical properties of the sodium and the consequences, quality control in a nuclear reactor, sodium treatment. (A.L.B.)

Outcome after burns: an observational study on burn scar maturation and predictors for severe scarring.

Science.gov (United States)

van der Wal, Martijn B A; Vloemans, Jos F P M; Tuinebreijer, Wim E; van de Ven, Peter; van Unen, Ella; van Zuijlen, Paul P M; Middelkoop, Esther

2012-01-01

Long-term outcome of burn scars as well as the relation with clinically relevant parameters has not been studied quantitatively. Therefore, we conducted a detailed analysis on the clinical changes of burn scars in a longitudinal setup. In addition, we focused on the differences in scar quality in relation to the depth, etiology of the burn wound and age of the patient. Burn scars of 474 patients were subjected to a scar assessment protocol 3, 6, and 12 months postburn. Three different age groups were defined (≤5, 5-18, and ≥18 years). The observer part of the patient and observer scar assessment scale revealed a significant (p burned (p  0.230) have no significant influence on scar quality when corrected for sex, total body surface area burned, time, and age or etiology, respectively. © 2012 by the Wound Healing Society.

Lawn mower-related burns.

Science.gov (United States)

Still, J; Orlet, H; Law, E; Gertler, C

2000-01-01

Lawn mower-related injuries are fairly common and are usually caused by the mower blades. Burns may also be associated with the use of power lawn mowers. We describe 27 lawn mower-related burn injuries of 24 male patients and 3 female patients. Three of the patients with burn injuries were children. Burn sizes ranged from 1% to 99% of the total body surface area (mean, 18.1%). Two of the patients died. The hospital stay ranged from 1 day to 45 days. Twenty-six injuries involved gasoline, which is frequently associated with refueling accidents. Safety measures should involve keeping children away from lawn mowers that are being used. The proper use and storage of gasoline is stressed.

Termite: Emulation Testbed for Encounter Networks

Directory of Open Access Journals (Sweden)

Rodrigo Bruno

2015-08-01

Full Text Available Cutting-edge mobile devices like smartphones and tablets are equipped with various infrastructureless wireless interfaces, such as WiFi Direct and Bluetooth. Such technologies allow for novel mobile applications that take advantage of casual encounters between co-located users. However, the need to mimic the behavior of real-world encounter networks makes testing and debugging of such applications hard tasks. We present Termite, an emulation testbed for encounter networks. Our system allows developers to run their applications on a virtual encounter network emulated by software. Developers can model arbitrary encounter networks and specify user interactions on the emulated virtual devices. To facilitate testing and debugging, developers can place breakpoints, inspect the runtime state of virtual nodes, and run experiments in a stepwise fashion. Termite defines its own Petri Net variant to model the dynamically changing topology and synthesize user interactions with virtual devices. The system is designed to efficiently multiplex an underlying emulation hosting infrastructure across multiple developers, and to support heterogeneous mobile platforms. Our current system implementation supports virtual Android devices communicating over WiFi Direct networks and runs on top of a local cloud infrastructure. We evaluated our system using emulator network traces, and found that Termite is expressive and performs well.

Ciguatoxins activate specific cold pain pathways to elicit burning pain from cooling.

Science.gov (United States)

Vetter, Irina; Touska, Filip; Hess, Andreas; Hinsbey, Rachel; Sattler, Simon; Lampert, Angelika; Sergejeva, Marina; Sharov, Anastasia; Collins, Lindon S; Eberhardt, Mirjam; Engel, Matthias; Cabot, Peter J; Wood, John N; Vlachová, Viktorie; Reeh, Peter W; Lewis, Richard J; Zimmermann, Katharina

2012-10-03

Ciguatoxins are sodium channel activator toxins that cause ciguatera, the most common form of ichthyosarcotoxism, which presents with peripheral sensory disturbances, including the pathognomonic symptom of cold allodynia which is characterized by intense stabbing and burning pain in response to mild cooling. We show that intraplantar injection of P-CTX-1 elicits cold allodynia in mice by targeting specific unmyelinated and myelinated primary sensory neurons. These include both tetrodotoxin-resistant, TRPA1-expressing peptidergic C-fibres and tetrodotoxin-sensitive A-fibres. P-CTX-1 does not directly open heterologously expressed TRPA1, but when co-expressed with Na(v) channels, sodium channel activation by P-CTX-1 is sufficient to drive TRPA1-dependent calcium influx that is responsible for the development of cold allodynia, as evidenced by a large reduction of excitatory effect of P-CTX-1 on TRPA1-deficient nociceptive C-fibres and of ciguatoxin-induced cold allodynia in TRPA1-null mutant mice. Functional MRI studies revealed that ciguatoxin-induced cold allodynia enhanced the BOLD (Blood Oxygenation Level Dependent) signal, an effect that was blunted in TRPA1-deficient mice, confirming an important role for TRPA1 in the pathogenesis of cold allodynia.

Animal Models in Burn Research

Science.gov (United States)

Abdullahi, A.; Amini-Nik, S.; Jeschke, M.G

2014-01-01

Burn injury is a severe form of trauma affecting more than two million people in North America each year. Burn trauma is not a single pathophysiological event but a devastating injury that causes structural and functional deficits in numerous organ systems. Due to its complexity and the involvement of multiple organs, in vitro experiments cannot capture this complexity nor address the pathophysiology. In the past two decades, a number of burn animal models have been developed to replicate the various aspects of burn injury; to elucidate the pathophysiology and explore potential treatment interventions. Understanding the advantages and limitations of these animal models is essential for the design and development of treatments that are clinically relevant to humans. This review paper aims to highlight the common animal models of burn injury in order to provide investigators with a better understanding of the benefits and limitations of these models for translational applications. While many animal models of burn exist, we limit our discussion to the skin healing of mouse, rat, and pig. Additionally, we briefly explain hypermetabolic characteristics of burn injury and the animal model utilized to study this phenomena. Finally, we discuss the economic costs associated with each of these models in order to guide decisions of choosing the appropriate animal model for burn research. PMID:24714880

Knowledge of childhood burn risks and burn first aid: Cool Runnings.

Science.gov (United States)

Burgess, Jacqueline D; Watt, Kerrianne A; Kimble, Roy M; Cameron, Cate M

2018-01-31

The high incidence of hot beverage scalds among young children has not changed in the past 15 years, but preventive campaigns have been scarce. A novel approach was used to engage mothers of young children in an app-based hot beverage scald prevention campaign 'Cool Runnings'. This paper provides baseline data for this randomised controlled trial (RCT). Queensland-based mothers aged 18+ years with at least one child aged 5-12 months were recruited via social media to Cool Runnings, which is a two-group, parallel, single-blinded RCT. In total, 498 participants from across Queensland completed the baseline questionnaire. The most common source of burn first aid information was the internet (79%). One-third (33%) correctly identified hot beverage scalds as the leading cause of childhood burns, 43% knew the age group most at risk. While 94% reported they would cool a burn with water, only 10% reported the recommended 20min duration. After adjusting for all relevant variables, there were two independent predictors of adequate burn first aid knowledge: first aid training in the past year (OR=3.32; 95% CI 1.8 to 6.1) and smoking status (OR=0.17; 95% CI 0.04 to 0.7). In this study, mothers of young children were largely unaware how frequently hot beverage scalds occur and the age group most susceptible to them. Inadequate burn first aid knowledge is prevalent across mothers of young children; there is an urgent and compelling need to improve burn first aid knowledge in this group. Given the high incidence of hot beverages scalds in children aged 6-24 months, it is important to target future burn prevention/first aid campaigns at parents of young children. ACTRN12616000019404; Pre-results. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Burn-out

OpenAIRE

Patricia van Echtelt

2014-01-01

Deze publicatie is alleen elektronisch verkrijgbaar (downloaden van deze site) Burn-out (ofwel: emotionele uitputting) komt relatief vaak voor: ongeveer één op de acht werknemers in Nederland heeft er last van. Het wordt dan ook gezien als een serieus maatschappelijk probleem dat beleidsmatig aandacht vergt. Dit rapport presenteert de resultaten van twee specifieke analyses over burn-out. Ten eerste gaan we na wat het effect is van emotionele uitputting op de loopbaan van werknemers. Ten twee...

Sodium pool fire analysis of sodium-cooled fast reactor by calculation

International Nuclear Information System (INIS)

Yu Hong; Xu Mi; Jin Degui

2002-01-01

Theoretical models were established according to the characteristic of sodium pool fire, and the SPOOL code was created independently. Some transient processes in sodium pool fire were modeled, including chemical reaction of sodium and oxygen; sodium combustion heat transfer modes in several kids of media; production, deposition and discharge of sodium aerosol; mass and energy exchange between different media in different ventilating conditions. The important characteristic parameters were calculated, such as pressure and temperature of gas, temperature of building materials, mass concentration of sodium aerosol, and so on. The SPOOL code, which provided available safety analysis tool for sodium pool fire accidents in sodium-cooled fast reactor, was well demonstrated with experimental data

Outpatient presentations to burn centers: data from the Burns Registry of Australia and New Zealand outpatient pilot project.

Science.gov (United States)

Gabbe, Belinda J; Watterson, Dina M; Singer, Yvonne; Darton, Anne

2015-05-01

Most studies about burn injury focus on admitted cases. To compare outpatient and inpatient presentations at burn centers in Australia to inform the establishment of a repository for outpatient burn injury. Data for sequential outpatient presentations were collected at seven burn centers in Australia between December 2010 and May 2011 and compared with inpatient admissions from these centers recorded by the Burns Registry of Australia and New Zealand for the corresponding period. There were 788 outpatient and 360 inpatient presentations. Pediatric outpatients included more children burns (39% vs 24%). Adult outpatients included fewer males (58% vs 73%) and intentional injuries (3.3% vs 10%), and more scald (46% vs 30%) and contact burns (24% vs 13%). All pediatric, and 98% of adult, outpatient presentations involved a %TBSAburns presenting to burn centers differed to inpatient admission data, particularly with respect to etiology and burn severity, highlighting the importance of the need for outpatient data to enhance burn injury surveillance and inform prevention. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

High burn rate solid composite propellants

Science.gov (United States)

Manship, Timothy D.

High burn rate propellants help maintain high levels of thrust without requiring complex, high surface area grain geometries. Utilizing high burn rate propellants allows for simplified grain geometries that not only make production of the grains easier, but the simplified grains tend to have better mechanical strength, which is important in missiles undergoing high-g accelerations. Additionally, high burn rate propellants allow for a higher volumetric loading which reduces the overall missile's size and weight. The purpose of this study is to present methods of achieving a high burn rate propellant and to develop a composite propellant formulation that burns at 1.5 inches per second at 1000 psia. In this study, several means of achieving a high burn rate propellant were presented. In addition, several candidate approaches were evaluated using the Kepner-Tregoe method with hydroxyl terminated polybutadiene (HTPB)-based propellants using burn rate modifiers and dicyclopentadiene (DCPD)-based propellants being selected for further evaluation. Propellants with varying levels of nano-aluminum, nano-iron oxide, FeBTA, and overall solids loading were produced using the HTPB binder and evaluated in order to determine the effect the various ingredients have on the burn rate and to find a formulation that provides the burn rate desired. Experiments were conducted to compare the burn rates of propellants using the binders HTPB and DCPD. The DCPD formulation matched that of the baseline HTPB mix. Finally, GAP-plasticized DCPD gumstock dogbones were attempted to be made for mechanical evaluation. Results from the study show that nano-additives have a substantial effect on propellant burn rate with nano-iron oxide having the largest influence. Of the formulations tested, the highest burn rate was a 84% solids loading mix using nano-aluminum nano-iron oxide, and ammonium perchlorate in a 3:1(20 micron: 200 micron) ratio which achieved a burn rate of 1.2 inches per second at 1000

Community integration after burn injuries.

Science.gov (United States)

Esselman, P C; Ptacek, J T; Kowalske, K; Cromes, G F; deLateur, B J; Engrav, L H

2001-01-01

Evaluation of community integration is a meaningful outcome criterion after major burn injury. The Community Integration Questionnaire (CIQ) was administered to 463 individuals with major burn injuries. The CIQ results in Total, Home Integration, Social Integration, and Productivity scores. The purposes of this study were to determine change in CIQ scores over time and what burn injury and demographic factors predict CIQ scores. The CIQ scores did not change significantly from 6 to 12 to 24 months postburn injury. Home integration scores were best predicted by sex and living situation; Social Integration scores by marital status; and Productivity scores by functional outcome, burn severity, age, and preburn work factors. The data demonstrate that individuals with burn injuries have significant difficulties with community integration due to burn and nonburn related factors. CIQ scores did not improve over time but improvement may have occurred before the initial 6-month postburn injury follow-up in this study.

The effect of inhalation aromatherapy with damask rose (Rosa damascena) essence on the pain intensity after dressing in patients with burns: A clinical randomized trial.

Science.gov (United States)

Bikmoradi, Ali; Harorani, Mehdi; Roshanaei, Ghodratollah; Moradkhani, Shirin; Falahinia, Golam Hossein

2016-01-01

Pain is one of the common problems encountered by patients with burns, which increases after each dressing. This study aimed to investigate the effect of inhalation aromatherapy with damask rose essence on the pain of patients with burns that is caused after dressing. A randomized clinical trial was conducted on 50 patients with second- and third-degree burn wounds. The baseline pain of the patients was assessed 30 min before they entered into the dressing room on the first and second days of intervention. The patients in the experimental group inhaled five drops of damask rose essence 40% in distilled water, while those in the control group inhaled five drops of distilled water as placebo. The pain intensity was assessed using Visual Analogue Scale at 15 and 30 min after the patients exited from the dressing room. Data were analyzed by SPSS (version 18) using descriptive and inferential statistics. There was significant difference between the mean of pain intensity before and after intervention at 15 and 30 min after dressing (P rose could be effective for relieving the pain caused after dressing in patients with burns. Therefore, it could be suggested as a complementary therapy in burn patients for pain relief.

Is there a threshold age and burn size associated with poor outcomes in the elderly after burn injury?

Science.gov (United States)

Jeschke, Marc G; Pinto, Ruxandra; Costford, Sheila R.; Amini-Nik, Saeid

2016-01-01

Elderly burn care represents a vast challenge. The elderly are one of the most susceptible populations to burn injuries, but also one of the fastest growing demographics, indicating a substantial increase in patient numbers in the near future. Despite the need and importance of elderly burn care, survival of elderly burn patients is poor. Additionally, little is known about the responses of elderly patients after burn. One central question that has not been answered is what age defines an elderly patient. The current study was conducted to determine whether there is a cut-off age for elderly burn patients that is correlated with an increased risk for mortality and to determine the burn size in modern burn care that is associated with increased mortality. To answer these questions, we applied appropriate statistical analyses to the Ross Tilley Burn Centre and the Inflammatory and Host Response to Injury databases. We could not find a clear cut-off age that differentiates or predicts between survival and death. Risk of death increased linearly with increasing age. Additionally, we found that the LD50 decreases from 45% total body surface area (TBSA) to 25% TBSA from the age of 55 years to the age of 70 years, indicating that even small burns lead to poor outcome in the elderly. We therefore concluded that age is not an ideal to predictor of burn outcome, but we strongly suggest that burn care providers be aware that if an elderly patient sustains even a 25% TBSA burn, the risk of mortality is 50% despite the implementation of modern protocolized burn care. PMID:26803373

Crude oil burning mechanisms

DEFF Research Database (Denmark)

van Gelderen, Laurens; Malmquist, L.M.V.; Jomaas, Grunde

2015-01-01

In order to improve predictions for the burning efficiency and the residue composition of in-situ burning of crude oil, the burning mechanism of crude oil was studied in relation to the composition of its hydrocarbon mixture, before, during and after the burning. The surface temperature, flame...... height, mass loss rate and residues of three hydrocarbon liquids (n-octane, dodecane and hexadecane), two crude oils (DUC and REBCO) and one hydrocarbon liquid mixture of the aforementioned hydrocarbon liquids were studied using the Crude Oil Flammability Apparatus. The experimental results were compared...... on the highest achievable oil slick temperature. Based on this mechanism, predictions can then be made depending on the hydrocarbon composition of the fuel and the measured surface temperature....

[Influence of three-level collaboration network of pediatric burns treatment in Anhui province on treatment effects of burn children].

Science.gov (United States)

Xia, Z G; Zhou, X L; Kong, W C; Li, X Z; Song, J H; Fang, L S; Hu, D L; Cai, C; Tang, Y Z; Yu, Y X; Wang, C H; Xu, Q L

2018-03-20

Objective: To explore the influence of three-level collaboration network of pediatric burns in Anhui province on treatment effects of burn children. Methods: The data of medical records of pediatric burn children transferred from Lu'an People's Hospital and Fuyang People's Hospital to the First Affiliated Hospital of Anhui Medical University from January 2014 to December 2015 and January 2016 to September 2017 (before and after establishing three-level collaboration network of pediatric burns treatment) were analyzed: percentage of transferred burn children to hospitalized burn children in corresponding period, gender, age, burn degree, treatment method, treatment result, occurrence and treatment result of shock, and operative and non-operative treatment time and cost. Rehabilitation result of burn children transferred back to local hospitals in 2016 and 2017. Data were processed with t test, chi-square test, Mann-Whitney U test, and Fisher's exact test. Results: (1) Percentage of burn children transferred from January 2014 to December 2015 was 34.3% (291/848) of the total number of hospitalized burn children in the same period of time, which was close to 30.4% (210/691) of burn children transferred from January 2016 to September 2017 ( χ (2)=2.672, P >0.05). (2) Gender, age, burn degree, and treatment method of burn children transferred from the two periods of time were close ( χ (2)=3.382, Z =-1.917, -1.911, χ (2)=3.133, P >0.05). (3) Cure rates of children with mild, moderate, and severe burns transferred from January 2016 to September 2017 were significantly higher than those of burn children transferred from January 2014 to December 2015 ( χ (2)=11.777, 6.948, 4.310, P burns transferred from the two periods of time were close ( χ (2)=1.181, P >0.05). (4) Children with mild and moderate burns transferred from the two periods of time were with no shock. The incidence of shock of children with severe burns transferred from January 2014 to December 2015 was 6

A rare case of failed healing in previously burned skin after a secondary burns.

Science.gov (United States)

Goldie, Stephen J; Parsons, Shaun; Menezes, Hana; Ives, Andrew; Cleland, Heather

2017-01-01

Patients presenting with large surface area burns are common in our practice; however, patients with a secondary large burn on pre-existing burn scars and grafts are rare and not reported. We report on an unusual case of a patient sustaining a secondary large burn to areas previously injured by a burn from a different mechanism. We discuss the potential implications when managing a case like this and suggest potential biological reasons why the skin may behave differently. Our patient was a 33-year-old man who presented with a 5% TBSA burn on skin scarred by a previous 40% total body surface area (TBSA) burn and skin grafts. Initially assessed as superficial partial thickness in depth, the wounds were treated conservatively with dressings; however, they failed to heal and became infected requiring surgical management. Burns sustained in areas of previous burn scars and grafts may behave differently to normal patterns of healing, requiring more aggressive management and surgical intervention at an early stage.

UO2/sodium thermal interaction experiments at AWRE foulness since January 1972

International Nuclear Information System (INIS)

Darby, K.I.; Pottinger, R.C.; Turner, R.G.; Rees, N.J.M.

With an interaction rig described in an earlier report a number of performance tests were carried out. The unwanted gas content of the pyrotechnic charge has been identified as adsorbed water vapor. Calorimetric firings have confirmed the total theoretical energy release and chemical analyses of the debris showed that the pyrotechnic reaction had burnt to completion: experiments to correlate rate of charge burning with the pressure rise are proceeding. Charges with UO 2 diluent instead of the previously used Al 2 O 3 have been fired under sodium and water producing identical effects. One tries to separate debris from sodium by distillation. Pyrotechnic charges diluted with aluminium or silver were fired in a viewing cell, the design of which is described. A very high gas blanket pressure probably due to vapor pressure effects from the charge were observed. One frictional plate has been used with a negligible effect on measured gas blanket pressure. As a means to limit the first bubble excursion same firings were made with an increased gas blanket pressure

Global Diabetes Encounters

DEFF Research Database (Denmark)

Juul Nielsen, Annegrete; Langstrup, Henriette

2014-01-01

As already recognized, though little theorized within International Relations, the capacity of technology to ensure the achievement of preset policy goals is often grossly overrated. Drawing on Science and Technology Studies, this chapter proposes a lens to investigate global encounters, which ta...

Repeated Prescribed Burning in Aspen

Science.gov (United States)

Donald A. Perala

1974-01-01

Infrequent burning weather, low flammability of the aspen-hardwood association, and prolific sprouting and seeding of shrubs and hardwoods made repeated dormant season burning a poor tool to convert good site aspen to conifers. Repeat fall burns for wildlife habitat maintenance is workable if species composition changes are not important.

Low sodium diet (image)

Science.gov (United States)

... for you. Look for these words on labels: low-sodium, sodium-free, no salt added, sodium-reduced, ... for you. Look for these words on labels: low-sodium, sodium-free, no salt added, sodium-reduced, ...

Scientific Opinion on the safety evaluation of the active substances, sodium carbonate peroxyhydrate coated with sodium carbonate and sodium silicate, bentonite, sodium chloride, sodium carbonate for use in active food contact materials

OpenAIRE

EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids (CEF)

2013-01-01

This scientific opinion of the Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids deals with the safety evaluation of the powder mixture of the active substances sodium carbonate peroxyhydrate coated with sodium carbonate and sodium silicate (FCM substance No 1009), bentonite (CAS No 1302-78-9, FCM No 393), sodium chloride (CAS No 7647-14-5, FCM No 985), sodium carbonate (CAS No 497-19-8, FCM No 1008) which are intended to be used as combined oxygen generator and carbon...

Effect of ascorbate ions in DTPA treatment after contamination by mixed plutonium dioxide-sodium burning products

International Nuclear Information System (INIS)

Metivier, H.; Masse, R.; Nolibe, D.; Nenot, J.C.; Lafuma, J.

1977-01-01

Plutonium toxicity problems arising from the use of molten sodium cooled fast breeder reactors involving the accidental mixing and ignition of sodium contaminated by plutonium dioxide have been investigated. The possibility of using the strong reducing agent, ascorbate ion, in order to reduce Pu VI to a chemical form more complexable by DTPA, has been tested using male and female rats. Urine, feces, liver and skeletal measurements of 239 Pu daughter products were carried out. It was shown that the transportable fraction was not significantly modified by the associate ascorbate-DTPA treatment. However the skeletal burden which represents 2.2% with DTPA, reached only 1.6% with ascorbate association and 0.3% with preventive ascorbate injections. Whatever the DTPA ascorbate treatment, the liver burden was not modified significantly. Difference observable only with preventive ascorbate treatment cancels out ascorbate association in order to greatly increase DTPA therapy efficiency, but seems to indicate that the Pu-proteins associations in blood is reduced more easily by ascorbate than association of Pu with local proteins. Ascorbate reduction can also be observed in urinary elimination in that preventive ascorbate, followed by DTPA-ascorbate, leads to a quicker urinary elimination than DTPA or DTPA plus ascorbate post treatment. (U.K.)

Development of sodium disposal technology. Experiment of sodium compound solidification process

International Nuclear Information System (INIS)

Matsumoto, Toshiyuki; Ohura, Masato; Yatoh, Yasuo

2007-07-01

A large amount of sodium containing radioactive waste will come up at the time of final shutdown/decommission of FBR plant. The radioactive waste is managed as solid state material in a closed can in Japan. As for the sodium, there is no established method to convert the radioactive sodium to solid waste. Further, the sodium is highly reactive. Thus, it is recommended to convert the sodium to a stable substance before the solidification process. One of the stabilizing methods is conversion of sodium into sodium hydroxide solution. These stabilization and solidification processes should be safe, economical, and efficient. In order to develop such sodium disposal technology, nonradioactive sodium was used and a basic experiment was performed. Waste-fluid Slag Solidification method was employed as the solidification process of sodium hydroxide solution. Experimental parameters were mixing ratio of the sodium hydroxide and the slag solidification material, temperature and concentration of the sodium hydroxide. The best parameters were obtained to achieve the maximum filling ratio of the sodium hydroxide under a condition of enough high compressive strength of the solidified waste. In a beaker level test, the solidified waste was kept in a long term and it was shown that there was no change of appearance, density, and also the compressive strength was kept at a target value. In a real scale test, homogeneous profiles of the density and the compressive strength were obtained. The compressive strength was higher than the target value. It was shown that the Waste-fluid Slag Solidification method can be applied to the solidification process of the sodium hydroxide solution, which was produced by the stabilization process. (author)

21 CFR 880.5180 - Burn sheet.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Burn sheet. 880.5180 Section 880.5180 Food and... Burn sheet. (a) Identification. A burn sheet is a device made of a porous material that is wrapped aroung a burn victim to retain body heat, to absorb wound exudate, and to serve as a barrier against...

Physical functional outcome assessment of patients with major burns admitted to a UK Burn Intensive Care Unit.

Science.gov (United States)

Smailes, Sarah T; Engelsman, Kayleen; Dziewulski, Peter

2013-02-01

Determining the discharge outcome of burn patients can be challenging and therefore a validated objective measure of functional independence would assist with this process. We developed the Functional Assessment for Burns (FAB) score to measure burn patients' functional independence. FAB scores were taken on discharge from ICU (FAB 1) and on discharge from inpatient burn care (FAB 2) in 56 patients meeting the American Burn Association criteria for major burn. We retrospectively analysed prospectively collected data to measure the progress of patients' physical functional outcomes and to evaluate the predictive validity of the FAB score for discharge outcome. Mean age was 38.6 years and median burn size 35%. Significant improvements were made in the physical functional outcomes between FAB 1 and FAB 2 scores (pburn patients. Copyright © 2012 Elsevier Ltd and ISBI. All rights reserved.

Ileocolic perforation secondary to sodium polystyrene sulfonate in sorbitol use: A case report

Science.gov (United States)

Trottier, Vincent; Drolet, Sébastien; Morcos, Mohib W

2009-01-01

Hyperkalemia is a common condition encountered in medical and surgical patients. It can lead to various complications including cardiac arrhythmias. Sodium polystyrene sulfonate (SPS) in sorbitol is an ion-exchange resin that can be used to treat hyperkalemia. It can be used in enema or in oral form. The present article describes the case of an intensive care unit patient who experienced severe, diffuse, intestinal perforation induced by the use of SPS-sorbitol, requiring multiple laparotomies, followed by a brief review of the relevant literature and recommendations regarding the use of SPS-sorbitol. PMID:19826644

A numerical approach for the study of large sodium spray fires and its application for SPX1

International Nuclear Information System (INIS)

Varet, T.; Leroy, B.; Barthez, M.; Malet, J.C.

1996-01-01

For the original design of SUPER-PHENIX, only pool fires were analysed for secondary sodium because these were thought to be the most likely. However, after the sodium spray fire at the solar plant of ALMERIA, an analysis of the consequences of secondary spray fire was undertaken. According to the French Safety Authority, the most penalizing cases of sodium leak and fire must be taken into account for each type of consequences, up to the complete rupture of a main secondary pipe. The experimental data available were mainly based on sodium flowrates in the range of ten kilograms per second, which are far below the leak flowrates obtained in case of a complete rupture of a main secondary pipe, i.e. several tons of sodium per second during a short time interval; moreover, it was obviously not possible to perform sodium tests with such high flowrate conditions. Consequently a complete methodology for the prediction of the behaviour of large sodium spray fires has been developed: the two-dimensional code PULSAR, which solves the two phase flow Navier-Stokes equations with source terms of mass and energy, is first used to evaluate the physical behaviour of a spray of sodium droplets in a cell in diverse conditions and thus to determine the burning rate. This last value is then used as data in the FEUMIX code in which other phenomena such as the dynamic response of pressure relief systems are described, in order to determine the pressure transient in the cell. This approach has been successfully tested using the experimental data available from past and recent tests, particularly the high flowrates tests IGNA 3602 and IGNA 3604. This numerical approach has been applied to the analysis of the consequences of postulated large sodium leaks in SUPER-PHENIX and allowed us to justify the hypotheses used to design the protective measures implemented on the plant, and thus the demonstration of safety with regard to large sodium leaks. (author)

Genital burns in the national burn repository: incidence, etiology, and impact on morbidity and mortality.

Science.gov (United States)

Harpole, Bethany G; Wibbenmeyer, Lucy A; Erickson, Bradley A

2014-02-01

To better characterize national genital burns (GBs) characteristics using a large burn registry. We hypothesized that mortality and morbidity will be higher in patients with GBs. The National Burn Repository, a large North American registry of hospitalized burn patients, was queried for patients with GB. Burn characteristics and mechanism, demographics, mortality, and surgical interventions were retrieved. Outcomes of interest were mortality, hospital-acquired infection (HAI), and surgical intervention on the genitalia. Adjusted odds ratios (aOR) for outcomes were determined with binomial logistic regression controlling for age, total burn surface area, race, length of stay, gender, and inhalation injury presence. GBs were present in 1245 cases of 71,895 burns (1.7%). Patients with GB had significantly greater average total burn surface area, length of stay, and mortality. In patients with GB, surgery of the genitalia was infrequent (10.4%), with the aOR of receiving surgery higher among men (aOR 2.7, P burns (aOR 3.1, P <.002). Presence of a GB increased the odds of HAI (aOR 3.0, P <.0001) and urinary tract infections (aOR 3.4, P <.0001). GB was also an independent predictor of mortality (aOR 1.54) even after adjusting for the increased HAI risk. GBs are rare but associated with higher HAI rates and higher mortality after adjusting for well-established mortality risk factors. Although a cause and effect relationship cannot be established using these registry data, we believe this study suggests the need for special management considerations in GB cases to improve overall outcomes. Copyright © 2014 Elsevier Inc. All rights reserved.

The Burns Registry of Australia and New Zealand: progressing the evidence base for burn care.

Science.gov (United States)

Cleland, Heather; Greenwood, John E; Wood, Fiona M; Read, David J; Wong She, Richard; Maitz, Peter; Castley, Andrew; Vandervord, John G; Simcock, Jeremy; Adams, Christopher D; Gabbe, Belinda J

2016-03-21

Analysis of data from the Burns Registry of Australia and New Zealand (BRANZ) to determine the extent of variation between participating units in treatment and in specific outcomes during the first 4 years of its operation. BRANZ, an initiative of the Australian and New Zealand Burn Association, is a clinical quality registry developed in accordance with the Australian Commission on Safety and Quality in Healthcare national operating principles. Patients with burn injury who fulfil pre-defined criteria are transferred to and managed in designated burn units. There are 17 adult and paediatric units in Australia and New Zealand that manage almost all patients with significant burn injury. Twelve of these units treat adult patients. Data on 7184 adult cases were contributed by ten acute adult burn units to the registry between July 2010 and June 2014.Major outcomes: In-hospital mortality, hospital length of stay, skin grafting rates, and rates of admission to intensive care units. Considerable variations in unit profiles (including numbers of patients treated), in treatment and in outcomes were identified. Despite the highly centralised delivery of care to patients with severe or complex burn injury, and the relatively small number of specialist burn units, we found significant variation between units in clinical management and in outcomes. BRANZ data from its first 4 years of operation support its feasibility and the value of further development of the registry. Based on these results, the focus of ongoing research is to improve understanding of the reasons for variations in practice and of their effect on outcomes for patients, and to develop evidence-informed clinical guidelines for burn management in Australia and New Zealand.

Development of the life impact burn recovery evaluation (LIBRE) profile: assessing burn survivors' social participation.

Science.gov (United States)

Kazis, Lewis E; Marino, Molly; Ni, Pengsheng; Soley Bori, Marina; Amaya, Flor; Dore, Emily; Ryan, Colleen M; Schneider, Jeff C; Shie, Vivian; Acton, Amy; Jette, Alan M

2017-10-01

Measuring the impact burn injuries have on social participation is integral to understanding and improving survivors' quality of life, yet there are no existing instruments that comprehensively measure the social participation of burn survivors. This project aimed to develop the Life Impact Burn Recovery Evaluation Profile (LIBRE), a patient-reported multidimensional assessment for understanding the social participation after burn injuries. 192 questions representing multiple social participation areas were administered to a convenience sample of 601 burn survivors. Exploratory factor analysis and confirmatory factor analysis (CFA) were used to identify the underlying structure of the data. Using item response theory methods, a Graded Response Model was applied for each identified sub-domain. The resultant multidimensional LIBRE Profile can be administered via Computerized Adaptive Testing (CAT) or fixed short forms. The study sample included 54.7% women with a mean age of 44.6 (SD 15.9) years. The average time since burn injury was 15.4 years (0-74 years) and the average total body surface area burned was 40% (1-97%). The CFA indicated acceptable fit statistics (CFI range 0.913-0.977, TLI range 0.904-0.974, RMSEA range 0.06-0.096). The six unidimensional scales were named: relationships with family and friends, social interactions, social activities, work and employment, romantic relationships, and sexual relationships. The marginal reliability of the full item bank and CATs ranged from 0.84 to 0.93, with ceiling effects less than 15% for all scales. The LIBRE Profile is a promising new measure of social participation following a burn injury that enables burn survivors and their care providers to measure social participation.

BurnCase 3D software validation study: Burn size measurement accuracy and inter-rater reliability.

Science.gov (United States)

Parvizi, Daryousch; Giretzlehner, Michael; Wurzer, Paul; Klein, Limor Dinur; Shoham, Yaron; Bohanon, Fredrick J; Haller, Herbert L; Tuca, Alexandru; Branski, Ludwik K; Lumenta, David B; Herndon, David N; Kamolz, Lars-P

2016-03-01

The aim of this study was to compare the accuracy of burn size estimation using the computer-assisted software BurnCase 3D (RISC Software GmbH, Hagenberg, Austria) with that using a 2D scan, considered to be the actual burn size. Thirty artificial burn areas were pre planned and prepared on three mannequins (one child, one female, and one male). Five trained physicians (raters) were asked to assess the size of all wound areas using BurnCase 3D software. The results were then compared with the real wound areas, as determined by 2D planimetry imaging. To examine inter-rater reliability, we performed an intraclass correlation analysis with a 95% confidence interval. The mean wound area estimations of the five raters using BurnCase 3D were in total 20.7±0.9% for the child, 27.2±1.5% for the female and 16.5±0.1% for the male mannequin. Our analysis showed relative overestimations of 0.4%, 2.8% and 1.5% for the child, female and male mannequins respectively, compared to the 2D scan. The intraclass correlation between the single raters for mean percentage of the artificial burn areas was 98.6%. There was also a high intraclass correlation between the single raters and the 2D Scan visible. BurnCase 3D is a valid and reliable tool for the determination of total body surface area burned in standard models. Further clinical studies including different pediatric and overweight adult mannequins are warranted. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Frontcountry encounter norms among three cultures

Science.gov (United States)

Jerry J. Vaske; Maureen P. Donnelly; Robert M. Doctor; James P. Petruzzi

1995-01-01

Existing normative studies have focused on backcountry encounter norms reported by North Americans. This study extends previous research by comparing encounter norms reported by three different cultures - North Americans, Europeans, and Japanese - in a frontcountry day use recreation area. Data were obtained from on-site surveys distributed at the Columbia Icefield in...

Cosmopolitan encounters

DEFF Research Database (Denmark)

Plage, Stefanie; Willing, Indigo; Woodward, Ian

2017-01-01

This study contributes to the growing research on everyday cosmopolitanism in diverse societies. We employ a cosmopolitan encounters framework to explore the reflexive openness people perform and the ethical reasoning they draw on to get along with each other. In particular, we look beyond....... The ethical framework we propose is grounded in reflexive acts of sharing going beyond notions of giving and performing hospitality within a host/guest dyad....

Accuracy of burn size estimation in patients transferred to adult Burn Units in Sydney, Australia: an audit of 698 patients.

Science.gov (United States)

Harish, Varun; Raymond, Andrew P; Issler, Andrea C; Lajevardi, Sepehr S; Chang, Ling-Yun; Maitz, Peter K M; Kennedy, Peter

2015-02-01

The purpose of this study was to compare burn size estimation between referring centres and Burn Units in adult patients transferred to Burn Units in Sydney, Australia. A review of all adults transferred to Burn Units in Sydney, Australia between January 2009 and August 2013 was performed. The TBSA estimated by the referring institution was compared with the TBSA measured at the Burns Unit. There were 698 adults transferred to a Burns Unit. Equivalent TBSA estimation between the referring hospital and Burns Unit occurred in 30% of patients. Overestimation occurred at a ratio exceeding 3:1 with respect to underestimation, with the difference between the referring institutions and Burns Unit estimation being statistically significant (Pburn-injured patients as well as in patients transferred more than 48h after the burn (Pburn (Pburns (≥20% TBSA) were found to have more satisfactory burn size estimations compared with less severe injuries (burn size assessment by referring centres. The systemic tendency for overestimation occurs throughout the entire TBSA spectrum, and persists with increasing time after the burn. Underestimation occurs less frequently but rises with increasing time after the burn and with increasing TBSA. Severe burns (≥20% TBSA) are more accurately estimated by the referring hospital. The inaccuracies in burn size assessment have the potential to result in suboptimal treatment and inappropriate referral to specialised Burn Units. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Due Regard Encounter Model Version 1.0

Science.gov (United States)

2013-08-19

Note that no existing model covers encoun- ters between two IFR aircraft in oceanic airspace. The reason for this is that one cannot observe encounters...encounters between instrument flight rules ( IFR ) and non- IFR traffic beyond 12NM. 2 TABLE 1 Encounter model categories. Aircraft of Interest Intruder...Aircraft Location Flight Rule IFR VFR Noncooperative Noncooperative Conventional Unconventional CONUS IFR C C U X VFR C U U X Offshore IFR C C U X VFR C U

C-Scan Performance Test of Under-Sodium ultrasonic Waveguide Sensor in Sodium

International Nuclear Information System (INIS)

Joo, Young Sang; Bae, Jin Ho; Kim, Jong Bum

2011-01-01

Reactor core and in-vessel structures of a sodium-cooled fast (SFR) are submerged in opaque liquid sodium in the reactor vessel. The ultrasonic inspection techniques should be applied for observing the in-vessel structures under hot liquid sodium. Ultrasonic sensors such as immersion sensors and rod-type waveguide sensors have developed in order to apply under-sodium viewing of the in-vessel structures of SFR. Recently the novel plate-type ultrasonic waveguide sensor has been developed for the versatile application of under-sodium viewing in SFR. In previous studies, the ultrasonic waveguide sensor module was designed and manufactured, and the feasibility study of the ultrasonic waveguide sensor was performed. To improve the performance of the ultrasonic waveguide sensor in the under-sodium application, a new concept of ultrasonic waveguide sensors with a Be coated SS304 plate is suggested for the effective generation of a leaky wave in liquid sodium and the non-dispersive propagation of A 0 -mode Lamb wave in an ultrasonic waveguide sensor. In this study, the C-scan performance of the under-sodium ultrasonic waveguide sensor in sodium has been investigated by the experimental test in sodium. The under-sodium ultrasonic waveguide sensor and the sodium test facility with a glove box system and a sodium tank are designed and manufactured to carry out the performance test of under-sodium ultrasonic waveguide sensor in sodium environment condition

Burns in sub-Saharan Africa: A review.

Science.gov (United States)

Nthumba, Peter M

2016-03-01

Burns are important preventable causes of morbidity and mortality, with a disproportionate incidence in sub-Saharan Africa. The management of these injuries in sub-Saharan Africa is a challenge because of multiple other competing problems such as infectious diseases (HIV/AIDS, tuberculosis and malaria), terrorist acts and political instability. There is little investment in preventive measures, pre-hospital, in-hospital and post-discharge care of burns, resulting in high numbers of burns, high morbidity and mortality. Lack of data that can be used in legislation and policy formulation is a major hindrance in highlighting the problem of burns in this sub-region. An online search of publications on burns from sub-Saharan countries was performed. A total of 54 publications with 32,862 patients from 14 countries qualified for inclusion in the study. The average age was 15.3 years. Children aged 10 years and below represented over 80% of the burn patient population. Males constituted 55% of those who suffered burns. Scalds were the commonest cause of thermal injuries, accounting for 59% of all burns, while flame burns accounted for 33%. The burn mortality averaged 17%, or the death of one of every five burn victims. These statistics indicate the need for an urgent review of burn policies and related legislation across the sub-Saharan region to help reduce burns, and provide a safe environment for children. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Management of post burn hand deformities

Directory of Open Access Journals (Sweden)

Sabapathy S

2010-10-01

Full Text Available The hand is ranked among the three most frequent sites of burns scar contracture deformity. One of the major determinants of the quality of life in burns survivors is the functionality of the hands. Burns deformities, although largely preventable, nevertheless do occur when appropriate treatment is not provided in the acute situation or when they are part of a major burns. Reconstructive procedures can greatly improve the function of the hands. Appropriate choice of procedures and timing of surgery followed by supervised physiotherapy can be a boon for a burns survivor.

Global biomass burning. Atmospheric, climatic, and biospheric implications

International Nuclear Information System (INIS)

Levine, J.S.

1991-01-01

Biomass burning is a significant source of atmospheric gases and, as such, may contribute to global climate changes. Biomass burning includes burning forests and savanna grasslands for land clearing, burning agricultural stubble and waste after harvesting, and burning biomass fuels. The chapters in this volume include the following topics: remote sensing of biomass burning from space;geographical distribution of burning; combustion products of burning in tropical, temperate and boreal ecosystems; burning as a global source of atmospheric gases and particulates; impacts of biomass burning gases and particulates on global climate; and the role of biomass burning on biodiversity and past global extinctions. A total of 1428 references are cited for the 63 chapters. Individual chapters are indexed separately for the data bases

Burn-center quality improvement: are burn outcomes dependent on admitting facilities and is there a volume-outcome "sweet-spot"?

Science.gov (United States)

Hranjec, Tjasa; Turrentine, Florence E; Stukenborg, George; Young, Jeffrey S; Sawyer, Robert G; Calland, James F

2012-05-01

Risk factors of mortality in burn patients such as inhalation injury, patient age, and percent of total body surface area (%TBSA) burned have been identified in previous publications. However, little is known about the variability of mortality outcomes between burn centers and whether the admitting facilities or facility volumes can be recognized as predictors of mortality. De-identified data from 87,665 acute burn observations obtained from the National Burn Repository between 2003 and 2007 were used to estimate a multivariable logistic regression model that could predict patient mortality with reference to the admitting burn facility/facility volume, adjusted for differences in age, inhalation injury, %TBSA burned, and an additional factor, percent full thickness burn (%FTB). As previously reported, all three covariates (%TBSA burned, inhalation injury, and age) were found to be highly statistically significant risk factors of mortality in burn patients (P value improve the multivariable model. The treatment/admitting facility was found to be an independent mortality predictor, with certain hospitals having increased odds of death and others showing a protective effect (decreased odds ratio). Hospitals with high burn volumes had the highest risk of mortality. Mortality outcomes of patients with similar risk factors (%TBSA burned, inhalation injury, age, and %FTB) are significantly affected by the treating facility and their admission volumes.

Sodium safety manual

International Nuclear Information System (INIS)

Hayes, D.J.; Gardiner, R.L.

1980-09-01

The sodium safety manual is based upon more than a decade of experience with liquid sodium at Berkeley Nuclear Laboratories (BNL). It draws particularly from the expertise and experience developed in the course of research work into sodium fires and sodium water reactions. It draws also on information obtained from the UKAEA and other sodium users. Many of the broad principles will apply to other Establishments but much of the detail is specific to BNL and as a consequence its application at other sites may well be limited. Accidents with sodium are at best unpleasant and at worst lethal in an extremely painful way. The object of this manual is to help prevent sodium accidents. It is not intended to give detailed advice on specific precautions for particular situations, but rather to set out the overall strategy which will ensure that sodium activities will be pursued safely. More detail is generally conveyed to staff by the use of local instructions known as Sodium Working Procedures (SWP's) which are not reproduced in this manual although a list of current SWP's is included. Much attention is properly given to the safe design and operation of larger facilities; nevertheless evidence suggests that sodium accidents most frequently occur in small-scale work particularly in operations associated with sodium cleaning and special care is needed in all such cases. (U.K.)

Burn-related peripheral neuropathy: A systematic review.

Science.gov (United States)

Tu, Yiji; Lineaweaver, William C; Zheng, Xianyou; Chen, Zenggan; Mullins, Fred; Zhang, Feng

2017-06-01

Peripheral neuropathy is the most frequent disabling neuromuscular complication of burns. However, the insidious and progressive onset of burn neuropathy makes it often undiagnosed or overlooked. In our study, we reviewed the current studies on the burn-related peripheral neuropathy to summarize the morbidity, mechanism, detecting method and management of peripheral neuropathy in burn patients. Of the 1533 burn patients included in our study, 98 cases (6.39%) were presented with peripheral neuropathy. Thermal and electrical burns were the most common etiologies. Surgical procedures, especially nerve decompression, showed good effect on functional recovery of both acute and delayed peripheral neuropathy in burn patients. It is noteworthy that, for early detection and prevention of peripheral neuropathy, electrodiagnostic examinations should be performed on burn patients independent of symptoms. Still, the underlying mechanisms of burn-related peripheral neuropathy remain to be clarified. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Creating a social work link to the burn community: a research team goes to burn camp.

Science.gov (United States)

Williams, Nancy R; Reeves, Patricia M; Cox, Ellen R; Call, Serena B

2004-01-01

Social work faculty and graduate students conducted focus groups with 52 burn-injured adolescents from three burn camps to explore perceptions of their camp experience. Three themes emerged from data analysis that suggest burn camps play an important role in participants' lives. Camp is a place where burn-injured adolescents: (1) feel "normal" and accepted; (2) acquire insight in regard to self and meaning in life; and (3) gain confidence, increase self-esteem, and develop empathy. This project highlights how the use of qualitative research methods with grassroots organizations such as burn camps can serve as a link to greater social work involvement with this community.

High-velocity runaway stars from three-body encounters

Science.gov (United States)

Gvaramadze, V. V.; Gualandris, A.; Portegies Zwart, S.

2010-01-01

We performed numerical simulations of dynamical encounters between hard, massive binaries and a very massive star (VMS; formed through runaway mergers of ordinary stars in the dense core of a young massive star cluster) to explore the hypothesis that this dynamical process could be responsible for the origin of high-velocity (≥ 200 - 400 km s-1) early or late B-type stars. We estimated the typical velocities produced in encounters between very tight massive binaries and VMSs (of mass of ≥ 200 M⊙) and found that about 3 - 4% of all encounters produce velocities ≥ 400 km s-1, while in about 2% of encounters the escapers attain velocities exceeding the Milky Ways's escape velocity. We therefore argue that the origin of high-velocity (≥ 200 - 400 km s-1) runaway stars and at least some so-called hypervelocity stars could be associated with dynamical encounters between the tightest massive binaries and VMSs formed in the cores of star clusters. We also simulated dynamical encounters between tight massive binaries and single ordinary 50 - 100 M⊙ stars. We found that from 1 to ≃ 4% of these encounters can produce runaway stars with velocities of ≥ 300 - 400 km s-1 (typical of the bound population of high-velocity halo B-type stars) and occasionally (in less than 1% of encounters) produce hypervelocity (≥ 700 km s-1) late B-type escapers.

Current concepts on burn wound conversion – a review of recent advances in understanding the secondary progressions of burns

Science.gov (United States)

Salibian, Ara A.; Del Rosario, Angelica Tan; De Almeida Moura Severo, Lucio; Nguyen, Long; Banyard, Derek A.; Toranto, Jason D.; Evans, Gregory R.D.; Widgerow, Alan D.

2016-01-01

Burn wound conversion describes the process by which superficial partial thickness burns convert into deeper burns necessitating surgical intervention. Fully understanding and thus controlling this phenomenon continues to defy burn surgeons. However, potentially guiding burn wound progression so as to obviate the need for surgery while still bringing about healing with limited scarring is the major unmet challenge. Comprehending the pathophysiologic background contributing to deeper progression of these burns is an essential prerequisite to planning any intervention. In this study, a review of articles examining burn wound progression over the last five years was conducted to analyze trends in recent burn progression research, determine changes in understanding of the pathogenesis of burn conversion, and subsequently examine the direction for future research in developing therapies. The majority of recent research focuses on applying therapies from other disease processes to common underlying pathogenic mechanisms in burn conversion. While ischemia, inflammation, and free oxygen radicals continue to demonstrate a critical role in secondary necrosis, novel mechanisms such as autophagy have also been shown to contribute affect significantly burn progression significantly. Further research will have to determine whether multiple mechanisms should be targeted when developing clinical therapies. PMID:26787127

[Burns care following a nuclear incident].

Science.gov (United States)

Bargues, L; Donat, N; Jault, P; Leclerc, T

2010-09-30

Radiation injuries are usually caused by radioactive isotopes in industry. Detonations of nuclear reactors, the use of military nuclear weapons, and terrorist attacks represent a risk of mass burn casualties. Ionizing radiation creates thermal burns, acute radiation syndrome with pancytopenia, and a delayed cutaneous syndrome. After a latency period, skin symptoms appear and the depth of tissue damages increase with dose exposure. The usual burn resuscitation protocols have to be applied. Care of these victims also requires assessment of the level of radiation, plus decontamination by an experienced team. In nuclear disasters, the priority is to optimize the available resources and reserve treatment to patients with the highest probability of survival. After localized nuclear injury, assessment of burn depth and surgical techniques of skin coverage are the main difficulties in a burn centre. Training in medical facilities and burn centres is necessary in the preparation for management of the different types of burn injuries.

Urinary Sodium and Potassium Excretion and Dietary Sources of Sodium in Maputo, Mozambique

Directory of Open Access Journals (Sweden)

Ana Queiroz

2017-08-01

Full Text Available This study aimed to evaluate the urinary excretion of sodium and potassium, and to estimate the main food sources of sodium in Maputo dwellers. A cross-sectional evaluation of a sample of 100 hospital workers was conducted between October 2012 and May 2013. Sodium and potassium urinary excretion was assessed in a 24-h urine sample; creatinine excretion was used to exclude unlikely urine values. Food intake in the same period of urine collection was assessed using a 24-h dietary recall. The Food Processor Plus® was used to estimate sodium intake corresponding to naturally occurring sodium and sodium added to processed foods (non-discretionary sodium. Salt added during culinary preparations (discretionary sodium was computed as the difference between urinary sodium excretion and non-discretionary sodium. The mean (standard deviation urinary sodium excretion was 4220 (1830 mg/day, and 92% of the participants were above the World Health Organization (WHO recommendations. Discretionary sodium contributed 60.1% of total dietary sodium intake, followed by sodium from processed foods (29.0% and naturally occurring sodium (10.9%. The mean (standard deviation urinary potassium excretion was 1909 (778 mg/day, and 96% of the participants were below the WHO potassium intake recommendation. The mean (standard deviation sodium to potassium molar ratio was 4.2 (2.4. Interventions to decrease sodium and increase potassium intake are needed in Mozambique.

Processing changes across reading encounters.

Science.gov (United States)

Levy, B A; Newell, S; Snyder, J; Timmins, K

1986-10-01

Five experiments examined changes in the processing of a text across reading encounters. Experiment 1 showed that reading speed increased systematically across encounters, with no loss in the extensiveness of analyses of the printed text, as indicated by the ability to detect nonword errors embedded within that passage. Experiment 2 replicated this improved reading fluency with experience and showed that it occurred even with typescript changes across trials, thus indicating that a primed visual operations explanation cannot account for the effect. The third and fourth experiments then extended the study of the familiarity effect to higher level processing, as indicated by the detection of word errors. Familiarity facilitated the detection of these violations at the syntactic-semantic levels. Finally, Experiment 5 showed that these higher level violations continued to be well detected over a series of reading encounters with the same text. The results indicate that prior experience improves reading speed, with no attenuation of analysis of the printed words or of the passage's message.

A new metric for quantifying burn severity: The Relativized Burn Ratio

Science.gov (United States)

Sean A. Parks; Gregory K. Dillon; Carol Miller

2014-01-01

Satellite-inferred burn severity data have become increasingly popular over the last decade for management and research purposes. These data typically quantify spectral change between pre-and post-fire satellite images (usually Landsat). There is an active debate regarding which of the two main equations, the delta normalized burn ratio (dNBR) and its relativized form...

The collaborative project on European sodium fast reactor (CP ESFR project)

International Nuclear Information System (INIS)

Fiorini, Gian-Luigi

2010-01-01

The paper summarizes the key characteristics of the four years large Collaborative Project on European Sodium Fast Reactor (CP ESFR - 2009-2012); the CP ESFR follows the 6th FP project named 'Roadmap for a European Innovative SOdium cooled FAst Reactor - EISOFAR' further identifying, organizing and implementing a significant part of the needed R and D effort. The paper also gives insights concerning the so called 'working horses' cores and systems which are provided by CEA and AREVA and that will be used as a basis to test the performances and assess the pertinence of innovative solutions. The CP ESFR merges the contribution of 25 European partners (EU + CH); it will be performed under the aegis of the 7th Euratom FP under the Area - Advanced Nuclear Systems with a refund from the European Commission. It will be a key component of the European Sustainable Nuclear Energy Technology Platform (SNE TP) and its Strategic Research Agenda (SRA). The inputs for the project are the key research goals for fourth generation of European sodium cooled fast reactors which can be summarized as follows: an improved safety with in particular the achievement of a robust architecture vis-a-vis of abnormal situations and the robustness of the safety demonstrations; the guarantee of a financial risk similar to that of the other means of energy production; a flexible and robust management of nuclear materials and especially waste reduction through Minor Actinides burning

Ice & Fire: the Burning Question

DEFF Research Database (Denmark)

van Gelderen, Laurens; Jomaas, Grunde

2017-01-01

With the Arctic opening up to new shipping routes and increased oil exploration and production due to climate change, the risk of an Arctic oil spill is increasing. Of the classic oil spill response methods (mechanical recovery, dispersants and in-situ burning), in-situ burning is considered...... to be particularly a suitable response method in the Arctic. In-situ burning aims to remove the oil from the marine environment by burning it from the water surface. A recent Ph.D. thesis from the Technical University of Denmark has provided some new insights with respect to the fire science behind this response...

Assessment of flow induced vibration in a sodium-sodium heat exchanger

Energy Technology Data Exchange (ETDEWEB)

Prakash, V. [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India)], E-mail: prakash@igcar.gov.in; Thirumalai, M.; Prabhakar, R.; Vaidyanathan, G. [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India)

2009-01-15

The 500 MWe Prototype Fast Breeder Reactor (PFBR) is under construction at Kalpakkam. It is a liquid metal sodium cooled pool type fast reactor with all primary components located inside a sodium pool. The heat produced due to fission in the core is transported by primary sodium to the secondary sodium in a sodium to sodium Intermediate Heat Exchanger (IHX), which in turn is transferred to water in the steam generator. PFBR IHX is a shell and tube type heat exchanger with primary sodium on shell side and secondary sodium in the tube side. Since IHX is one of the critical components placed inside the radioactive primary sodium, trouble-free operation of the IHX is very much essential for power plant availability. To validate the design and the adequacy of the support system provided for the IHX, flow induced vibration (FIV) experiments were carried out in a water test loop on a 60 deg. sector model. This paper discusses the flow induced vibration measurements carried out in 60 deg. sector model of IHX, the modeling criteria, the results and conclusion.

The relevance of axial burn-up profiles for the criticality safety analysis of spent nuclear fuel in a final repository

International Nuclear Information System (INIS)

Kilger, R.; Gmal, B.; Moser, E.F.

2008-01-01

Due to inhomogeneous neutron flux and moderator density distributions in the reactor core, the burn-up of a nuclear fuel assembly is not homogeneous but shows an axial distribution, typically with lower partial burn-up and thus higher remaining reactivity at the fuel ends in particular at the assembly top end. Beyond a burn-up of about 15 to 20 GWd/tHM, the multiplication factor K of the whole assembly is dominated by this lower-burnt end regions, and is usually higher than for assuming a homogeneous uniform distribution of the averaged burn-up. This behaviour commonly referred to as positive ''end effect'' is well known in burn-up credit considerations for transportation and storage casks and is being investigated also in the context of criticality analyses for final disposition of spent nuclear fuel. Sign and value of the end effect depend on several parameters. Based on a generic model one may not conclude that criticality in a final repository is a likely or expected event, but nevertheless it draws the attention to the fact that criticality is not excluded per se but has to be considered in the analysis and probably has to be encountered by certain appropriate measures, maybe e.g. by limitation of the amount of fissile material inside one single cask, or a rigorous prove for prevention of water ingress. The authors also conclude that the higher partial reactivity of the fuel ends has to be accounted for carefully in more realistic analyses of post-closure scenarios with respect to criticality safety.

Sedation and Analgesia in Burn

Directory of Open Access Journals (Sweden)

Özkan Akıncı

2011-07-01

Full Text Available Burn injury is one of the most serious injuries that mankind may face. In addition to serious inflammation, excessive fluid loss, presence of hemodynamic instability due to intercurrent factors such as debridements, infections and organ failure, very different levels and intensities of pain, psychological problems such as traumatic stress disorder, depression, delirium at different levels that occur in patient with severe burn are the factors which make it difficult to provide the patient comfort. In addition to a mild to moderate level of baseline permanent pain in burn patients, which is due to tissue damage, there is procedural pain as well, which occurs by treatments such as grafting and dressings, that are severe, short-term burst style 'breakthrough' pain. Movement and tactile stimuli are also seen in burn injury as an effect to sensitize the peripheral and central nervous system. Even though many burn centers have established protocols to struggle with the pain, studies show that pain relief still inadequate in burn patients. Therefore, the treatment of burn pain and the prevention of possible emergence of future psychiatric problems suc as post-traumatic stress disorder, the sedative and anxiolytic agents should be used as a recommendation according to the needs and hemodynamic status of individual patient. (Journal of the Turkish Society Intensive Care 2011; 9 Suppl: 26-30

Survey of the Statewide Impact of Payer Source on Referral of Small Burns to Burn Centers.

Science.gov (United States)

Penny, Rachel; Coffey, Rebecca; Jones, Larry; Bailey, J Kevin

It is generally agreed that patients with large burns will be referred to organized burn centers, however, the referral of patients with smaller burns is less certain. A two-part survey was conducted to identify referral patterns for burn patients that meet American Burn Association referral criteria, and any effect insurance type might have on the referral patterns. The emergency departments of our state hospital association's member hospitals were contacted seeking a referral for a fictitious patient with a third-degree scald of the dominant hand. The referral sites were contacted twice, first stating that the patient had commercial insurance, next stating that the patient had Medicaid. Data collected included wait time for an appointment or reasons for denial of an appointment. Of 218 hospitals, 46 were excluded because they did not offer emergency care, and eight because they were listed as burn centers on the American Burn Association website. Of the remaining 164, 119 (73%) would refer to a burn center, 21 (13%) to a plastic surgeon, 10 (6%) to a hand surgeon, 7 (4%) to a wound center, 7 (4%) to another nonburn physician resource. There was no difference in wait time to the first available appointment with regards to insurance type (6.56 ± 4.68 vs 6.53 ± 5.05 days). Our state's referral pattern gives us insight into the regional referral pattern. This information will be used to guide a focused education and communication program to provide better service for the burn victims of our state.

Pediatric Burns: A Single Institution Retrospective Review of Incidence, Etiology, and Outcomes in 2273 Burn Patients (1995-2013).

Science.gov (United States)

Lee, Christina J; Mahendraraj, Krishnaraj; Houng, Abraham; Marano, Michael; Petrone, Sylvia; Lee, Robin; Chamberlain, Ronald S

Unintentional burn injury is the third most common cause of death in the U.S. for children age 5 to 9, and accounts for major morbidity in the pediatric population. Pediatric burn admission data from U.S. institutions has not been reported recently. This study assesses all pediatric burn admissions to a State wide Certified Burn Treatment Center to evaluate trends in demographics, burn incidence, and cause across different age groups. Demographic and clinical data were collected on 2273 pediatric burn patients during an 18-year period (1995-2013). Pediatric patients were stratified by age into "age 0 to 6," "age 7 to 12," and "age 13 to 18." Data were obtained from National Trauma Registry of the American College of Surgeons and analyzed using standard statistical methodology. A total of 2273 burn patients under age 18 were treated between 1995 and 2013. A total of 1663 (73.2%) patients were ages 0 to 6, 294 (12.9%) were 7 to 12, and 316 (13.9%) were age 13 to 18. A total of 1400 (61.6%) were male and 873 (38.4%) were female (male:female ratio of 1.6:1). Caucasians had the highest burn incidence across all age groups (40.9%), followed by African-Americans (33.6%), P burns occurred at home, P burned was 8.9%, with lower extremity being the most common site (38.5%). Scald burns constituted the majority of cases (71.1%, n = 1617), with 53% attributable to hot liquids related to cooking, including coffee or tea, P burns were the dominant cause (53.8%). Overall mean length of stay was 10.5 ± 10.8 days for all patients, and15.5 ± 12 for those admitted to the intensive care unit, P burn injuries are scald burns that occur at home and primarily affect the lower extremities in Caucasian and African-American males. Among Caucasian teenagers flame burns predominate. Mean length of stay was 10 days, 23% of patients required skin grafting surgery, and mortality was 0.9%. The results of this study highlight the need for primary prevention programs focusing on avoiding

Dental Encounter System (DES)

Data.gov (United States)

Department of Veterans Affairs — Dental Encounter System (DES) is an automated health care application designed to capture critical data about the operations of VA Dental Services. Information on...

Sodium vapor deposition onto a horizontal flat plate above liquid sodium surface, (3)

International Nuclear Information System (INIS)

Kudo, Kazuhiko; Hirata, Masaru.

1978-01-01

Sodium vapour and sodium mist in the cover gas of a sodium system of a fast breeder reactor cause various problems. In this report, with the results of measurements of sodium mist concentration, the distribution of sodium mist diameter in cover gas was analytically obtained. The analysis was made by using the different nucleus model B. The measurement of the concentration of sodium mist was carried out with a sodium mist pot designed by the author. The experiment was done at the sodium temperature of 400 and 500 degree centigrade. The relations among sodium temperature, upper wall temperature, and the sodium mist concentration in cover gas were obtained. Evaluation of effective condensed nuclear radius in the cover gas was made by the comparison of analysis and experimental results. The results of this evaluation shows the following conclusions. It is impossible to express the distribution of sodium mist diameter by normal distribution or logarithmic normal distribution. Drop of sodium temperature results in the decrease of weight mean radius of generated sodium mist. Drop of upper wall temperature causes the decrease of weight mean radius, and increases sodium mist concentration. (Kato, T.)

An investigation of sodium iodide solubility in sodium-stainless steel systems

International Nuclear Information System (INIS)

Sagawa, Norihiko; Tashiro, Suguru

1996-01-01

Sodium iodide and major constituents of stainless steel in sodium are determined by using the steel capsules to obtain a better understanding on contribution of the constituents to the apparent iodide solubility in sodium. The capsule loaded with 20 g sodium and 0.1 - 0.3 g powder of sodium iodide is heated at its upper part in a furnace and cooled at its bottom on brass plates to establish a large temperature gradient along the capsule tube. After a given period of equilibration, the iodide and constituents are fixed in solidified sodium by quick quenching of the capsules. Sodium samples are taken from the sectioned capsule tube and submitted to sodium dissolution by vaporized water for determination of the iodine and to vacuum distillation for determination of the metal elements. Iron and nickel concentrations are observed to be lower in the samples at higher iodine concentrations. Chromium and manganese concentrations are seen to be insensitive to the iodine concentrations. The observations can be interpreted by a model that sodium oxide combines with metal iodide in sodium to form a complex compound and with consideration that the compound will fall and deposit onto the bottom of the capsule by thermal diffusion. (author)

Ozone generation over the Indian Ocean during the South African biomass-burning period: case study of October 1992.

Directory of Open Access Journals (Sweden)

F. G. Taupin

2002-04-01

Full Text Available In this study, we present an estimation of photochemical ozone production during free tropospheric transport between the African biomass burning area and Reunion Island (Indian Ocean by means of trajectory-chemistry model calculations. Indeed, enhanced ozone concentrations (80–100 ppbv between 5 and 8 km height over Reunion Island are encountered during September–October when African biomass burning is active. The measurements performed during flight 10 of the TRACE-A campaign (October 6, 1992 have been used to initialise the lagrangian trajectory-chemistry model and several chemical forward trajectories, which reach the area of Reunion Island some days later, are calculated. We show that the ozone burden already present in the middle and upper troposphere over Southern Africa, formed from biomass burning emissions, is further enhanced by photochemical production over the Indian Ocean at the rate of 2.5 - 3 ppbv/day. The paper presents sensitivity studies of how these photochemical ozone production rates depend on initial conditions. The rates are also compared to those obtained by other studies over the Atlantic Ocean. The importance of our results for the regional ozone budget over the Indian Ocean is briefly discussed.Key words. Atmospheric composition and structure (evolution of the atmosphere; troposphere – composition and chemistry; meterorology and atmospheric dynamics (tropical meteorology

Involving burn survivors in agenda setting on burn research: an added value?

NARCIS (Netherlands)

Broerse, J.E.W.; Zweekhorst, M.B.M.; Van Rensen, A.J.M.L.; De Haan, M.J.M.

2010-01-01

Background and aim: The role of burn survivors in burn research is usually restricted to being objects of study and beneficiaries of research results, while decision-making on research is traditionally the domain of a small group of experts, mainly scientists. In this article we compare the research

49 CFR 173.189 - Batteries containing sodium or cells containing sodium.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Batteries containing sodium or cells containing sodium. 173.189 Section 173.189 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.189 Batteries containing sodium or cells containing sodium. (a...

A core performance study on an actinide recycling 'zero-sodium-void worth' core

International Nuclear Information System (INIS)

Kawashima, M.; Nakagawa, M.; Yamaoka, M.; Kasahara, F.

1994-01-01

A core performance study was made for an absorber-type parfait core (A-APC) as one of 'Zero-sodium-void-worth' core concepts. This evaluation study pursued different two aspects; one for transuranic (TRU) management strategy, and another for a loss-of-coolant anticipated transient behavior considering the unique core configuration. The results indicated that this core has a large flexibility for actinide recycling in terms of self-sufficiency and minor actinide burning. The result also showed that this core has kept a large mitigation potential for ULOF events as well as a simple flat core concept, reflecting detailed three dimensional core bowing behavior for the A-APC configuration. (author)

Orion Burn Management, Nominal and Response to Failures

Science.gov (United States)

Odegard, Ryan; Goodman, John L.; Barrett, Charles P.; Pohlkamp, Kara; Robinson, Shane

2016-01-01

An approach for managing Orion on-orbit burn execution is described for nominal and failure response scenarios. The burn management strategy for Orion takes into account per-burn variations in targeting, timing, and execution; crew and ground operator intervention and overrides; defined burn failure triggers and responses; and corresponding on-board software sequencing functionality. Burn-to- burn variations are managed through the identification of specific parameters that may be updated for each progressive burn. Failure triggers and automatic responses during the burn timeframe are defined to provide safety for the crew in the case of vehicle failures, along with override capabilities to ensure operational control of the vehicle. On-board sequencing software provides the timeline coordination for performing the required activities related to targeting, burn execution, and responding to burn failures.

Determinants of customer satisfaction with service encounter

Directory of Open Access Journals (Sweden)

Ariana Nefat

2008-12-01

Full Text Available Service encounters are the focal point of a customer’s perception of a service in terms of its quality, value and customer satisfaction. The paper researches the influence of the components of a service encounter on customer satisfaction. Among several factors that determine customer satisfaction the quality of service, which is related to the characteristics of service, plays an important role. However, a direct insight into the reasons that make a service encounter satisfactory or unsatisfactory is provided by the critical incident technique, where causes of dis/satisfaction differ primarily depending on whether they derive from interpersonal contact or from contact with technology. The evidence of service, which includes people, process and the physical evidence, plays a critical role in a customer’s dis/satisfaction. The influence of these elements cannot be observed separately; it must be observed in their interaction during the delivery of service and their strongest effect is achieved during face-to-face service encounters that have the characteristics of a theatre metaphor. Even though a high level of satisfaction may be achieved after the recovery of a service, enterprises should aim to conduct excellent service encounters right from the start.

Comparison of the General Health, Self-Esteem and Social Support in Self-Inflicted Burn Patients and Non Self Inflicted Burn Patients of the Choromy Accidental and Burning Hospital of Ganaveh

Directory of Open Access Journals (Sweden)

MS Enayati

2006-04-01

Full Text Available ABSTRACT: Introduction & Objective: Self-inflicted burn is a violent method of suicide. Since our society faces lots of psychological, social, personal and economical problems due to self-inflicted burn, more survey for this event can assist us to know its causes and prevent from its occurrence. This research was carried out to compare general health, self- esteem and social support in patient's self-inflicted burn and non-self-inflicted burn of the Choromy accidental and burning hospital in Ganaveh. Materials & Methods: This is a descriptive – analytic study. The sample consisted of 60 inpatients burnt (males & females of the Choromy accidental and burning hospital (Ganaveh. The method of sampling was simple random. Participants completed the General Health Questionnaire (G.H.Q- 28 of Goldberg, Cooper Smith’s questionnaire of self–esteem and Philip’s social support scale. Multivariate analysis of variance (MANOVA and T-test were the major statistical analysis in this research. Results: The mean and standard deviation of the general health were 44.57 ± 14.65 for self-inflicted burn persons and for non - self inflicted burn they were 10.83 ± 6.27. In the self–esteem variable, the mean and the standard deviation were 57.90 ± 4.94 for self-inflicted burn persons and 55.47 ± 6.04 for non-self inflicted burn ones. Mean and standard deviation of whole social supporting were 20.40 ± 4.94 for self-inflicted burn persons and 23.73 ± 1.17 for non-self inflicted burn group. The findings showed significant differences between the two groups from viewpoint of general health and social supporting while there were no significant differences between two groups in case of self–esteem. Conclusion: There are a significant relationship between general health, social supporting and self-inflicted burn.Therefore, in order to prevent self inflicted burn it is suggested that we make a relationship between persons and societies, families, groups and

Development of severe accident evaluation technology (level 2 PSA) for sodium-cooled fast reactors. (5) Identification of dominant factors in ex-vessel accident sequences

International Nuclear Information System (INIS)

Ohno, Shuji; Seino, Hiroshi; Miyahara, Shinya

2009-01-01

The evaluation of accident progression outside of a reactor vessel (ex-vessel) and subsequent transfer behavior of radioactive materials is of great importance from the viewpoint of Level 2 PSA. Hence typical ex-vessel accident sequences in the JAEA Sodium-cooled Fast Reactor are qualitatively discussed in this paper and dominant behaviors or factors in the sequences are investigated through parametric calculations using the CONTAIN/LMR code. Scenarios to be focused on are, 1) sodium vapor leakage from the reactor vessel and 2) sodium-concrete reaction, which are both to be considered in the accident category of LOHRS (loss of heat removal system) and might be followed by an early containment failure due to the thermal effect of sodium combustion and hydrogen burning respectively. The calculated results clarify that the sodium vapor leak rate and the scale of sodium-concrete reaction are the important factors to dominate the ex-vessel accident progression. In addition to the understandings of the dominant factors, the analyzed results also provide the specific information such as pressure loading value to the containment and the timing of pressurization, which is indispensable as technical base in Level 2 PSA for developing event trees and for quantifying the accident consequences. (author)

On the results of investigating cause of sodium leak accident in prototype fast breeder reactor 'Monju' in Power Reactor and Nuclear Fuel Development Corporation

International Nuclear Information System (INIS)

1997-01-01

The sodium leak accident in the secondary system of Monju occurred on December 8, 1995. The task force for investigating the accident was established in Nuclear Safety Bureau, and on May 23, 1996, the May report on the results of investigation was published. In order to elucidate the details of the fact that only one thermometer in the secondary system was broken and the reaction of leaked sodium with steel materials, the investigation was continued. In this report, also the results of these additional investigations are included. First, the accident of this time is outlined. As for the cause of the occurrence of sodium leak, the examination of the fracture surface of the broken thermometer, the high cycle fatigue due to hydrodynamic vibration, the investigation of the design, manufacture and installation of the thermometer, and the evaluation of secondary system thermometers which were not broken are reported. The cause that only one thermometer was broken was the way of its insertion which made the restraint of vibration amplitude ineffective. As the effects of sodium leak, the pile of sodium compound on floor liner, the damage of ducts and gratings, and the color change of concrete walls were observed. The burning experiment due to sodium leak was carried out to confirm the effects. (K.I.)

Global biomass burning: Atmospheric, climatic, and biospheric implications

International Nuclear Information System (INIS)

Levine, J.S.

1991-01-01

As a significant source of atmospheric gases, biomass burning must be addressed as a major environmental problem. Biomass burning includes burning forests and savanna grasslands for land clearing and conversion, burning agricultural stubble and waste after harvesting, and burning biomass fuels. The editor discusses the history of biomass burning and provides an overview of the individual chapters

Fire-fighting burning oil wells

International Nuclear Information System (INIS)

Newbury, Herbert; Risk, Stewart.

1993-01-01

A method of extinguishing burning oil wells is presented which involves dispensing liquid nitrogen to the burning site to prevent or inhibit oxygen from fuelling the flames. To carry out the method a remotely operated vehicle is described which is provided with a source of liquid nitrogen and an articulated deployment boom capable of supplying the liquid nitrogen to the site of a burning oil well. (Author)

Cavitation erosion in sodium flow, sodium cavitation tunnel testing

International Nuclear Information System (INIS)

Courbiere, Pierre.

1981-04-01

The high-volume sodium flows present in fast neutron reactors are liable to induce cavitation phenomena in various portion of the sodium lines and pumps. The absence of sufficient data in this area led the C.E.A. to undertake an erosion research program in cavitating sodium flow. This paper discusses the considerations leading to the definition and execution of sodium cavitation erosion tests, and reviews the tests run with 400 0 C sodium on various steel grades: 316, 316 L, 316 Ti (Z8CNDT17-12), Poral (Z3CND18-12), 304 L and LN2 - clad 316 L (Ni coating-clad 316 L). Acoustic detection and signal processing methods were used with an instrument package designed and implemented at the Cadarache Nuclear Research Center

Chemical characterisation of iron in dust and biomass burning aerosols during AMMA-SOP0/DABEX: implication for iron solubility

Directory of Open Access Journals (Sweden)

R. Paris

2010-05-01

Full Text Available The chemical composition and the soluble fraction were determined in aerosol samples collected during flights of AMMA-SOP0/DABEX campaign, which were conducted in the West African Sahel during dry season (2006. Two aerosol types are encountered in this period: dust particles (DUST and biomass burning aerosol (BB. Chemical analysis and microscope observations showed that the iron (Fe found in BB samples mainly originates from dust particles mostly internally mixed in the biomass burning layer. Chemical analyses of samples showed that the Fe solubility is lower in African dust samples than in biomass burning aerosols. Our data provide a first idea of the variability of iron dust solubility in the source region (0.1% and 3.4%. We found a relationship between iron solubility/clay content/source which partly confirms that the variability of iron solubility in this source region is related to the character and origin of the aerosols themselves. In the biomass burning samples, no relationship were found between Fe solubility and either the concentrations of acidic species (SO₄²⁻, NO₃⁻ or oxalate or the content of carbon (TC, OC, BC. Therefore, we were unable to determine what processes are involved in this increase of iron solubility. In terms of supply of soluble Fe to oceanic ecosystems on a global scale, the higher solubility observed for Fe in biomass burning could imply an indirect source of Fe to marine ecosystems. But these aerosols are probably not significant because the Sahara is easily the dominant source of Fe to the Atlantic Ocean.

Removal of sodium from the component of the sodium purification loop

International Nuclear Information System (INIS)

Kim, Byung Ho; Jeong, Kyung Chai; Jeong, Ji Young; Kim, Jong Man; Choi, Byung Hae; Nam, Ho Yun

2005-01-01

The purpose of a cleaning process is to remove the residual sodium adhering to the component walls once it has been properly drained. It is necessary to clean and decontaminate a component, especially the large components of the primary coolant system; such as the intermediate heat exchangers and the primary pump. Improper and inadequate cleaning has in a number of cases resulted in problems in the storage, handling, and reuse of components. Several types of failures due to improper cleaning procedures have been defined in the past. Inadequate and incomplete removal of sodium results in residues which may contain metallic sodium and alkaline compounds such as sodium hydroxide, sodium oxide, sodium carbonate, and various types of alcoholates. Reinsertion of components containing these compounds into a high-temperature sodium system can result in either the intergranular penetration characteristic of a high-oxygen sodium or an accelerated corrosion due to oxygen. The methods used for cleaning sodium equipment depend on the condition and types of equipment to be cleaned and whether the equipment is to be reused. Cleaning methods are needed that will avoid a deleterious local overheating, material surface degradation or deposits, chemical, physical, or mechanical damage, and external effects. This paper discusses a steam-nitrogen gas cleaning method for the routine applications that permits the reuse of the cold trap in sodium

In situ oil burning in the marshland environment : soil temperatures resulting from crude oil and diesel fuel burns

International Nuclear Information System (INIS)

Bryner, N.P.; Walton, W.D.; Twilley, W.H.; Roadarmel, G.; Mendelssohn, I.A.; Lin, Q.; Mullin, J.V.

2001-01-01

The unique challenge associated with oil spill cleanups in sensitive marsh environments was discussed. Mechanical recovery of crude or refined hydrocarbons in wetlands may cause more damage to the marsh than the oil itself. This study evaluated whether in situ burning of oiled marshlands would provide a less damaging alternative than mechanical recovery. This was done through a series of 6 crude oil and 5 diesel fuel burns conducted in a test tank to examine the impact of intentional burning of oil spilled in a wetlands environment. There are several factors which may influence how well such an environment would recover from an in situ oil burn, such as plant species, fuel type and load, water level, soil type, and burn duration. This paper focused on soil, air and water temperatures, as well as total heat fluxes that resulted when 3 plant species were exposed to full-scale in situ burns that were created by burning diesel fuel and crude oil. The soil temperatures were monitored during the test burn at three different soil/water elevations for 700 second burn exposures. A total of 184 plant sods were harvested from marshlands in southern Louisiana and were subjected to the burning fuel. They were instrumental in characterizing the thermal and chemical stress that occur during an in-situ burn. The plants were inserted into the test tanks at various water and soil depths. The results indicated that diesel fuel and crude oil burns produced similar soil temperature profiles at each of three plant sod elevations. Although in-situ burning did not appear to remediate oil that had penetrated into the soil, it did effectively remove floating oil from the water surface, thereby preventing it from potentially contaminating adjacent habitats and penetrating the soil when the water recedes. The regrowth and recovery of the plants will be described in a separate report. 25 refs., 7 tabs., 15 figs

Epidemiology of burns undergoing hospitalization to the National Burns Unit in the Sultanate of Oman: a 25-year review.

Science.gov (United States)

Al-Shaqsi, Sultan; Al-Kashmiri, Ammar; Al-Bulushi, Taimoor

2013-12-01

The aim of this study was to describe the epidemiology of burns admitted to the National Burns Unit (NBU) in the Sultanate of Oman between 1987 and 2011. This is a retrospective review of burn patients admitted to Oman's National Burns Unit (NBU) between 1987 and 2011. The data extracted from the national burn registry. The study describes the admission rate by gender and age groups, occupation, causes of burns, time-to-admission, length of stay and in-hospital mortality of burns between 1987 and 2011. During a 25-year from 1987 to 2011, there were 3531 burn patients admitted to the National Burns Unit in Oman. The average admission rate to NBU is 7.02 per 100,000 persons per year. On average, males were more likely to be admitted to the NBU than females during the study period (P value Oman. Children are disproportionately over-represented in this study. Prevention programmes are urgently needed to address this "silent and costly epidemic." Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

The Parameters Controlling the Burning Efficiency of In-Situ Burning of Crude Oil on Water

DEFF Research Database (Denmark)

van Gelderen, Laurens; Jomaas, Grunde

2017-01-01

Parameters that control the burning efficiency of in-situ burning of crude oil on water were identified by studying the influence of the initial slick thickness, vaporization order, oil slick diameter, weathering state of the oil, heat losses to the water layer and heat flux to the fuel surface...... on the burning efficiency for light and heavy crude oils. These parameters were studied in several small scale and intermediate scale experimental setups. The results showed that the heat losses to the water layer increase with increasing burning time because the components in a crude oil evaporate from volatile...... to non-volatile. Due to the relatively low heat feedback (reradiation and convection, in kW/m2) to the fuel surface of small scale pool fires, as compared to large scale pool fires, these heat losses were shown to limit the burning efficiency in small scale experiments. By subjecting small scale crude...

Fancy a cup of scald? - The role of hot beverage burns in paediatric burns admissions in Ireland.

Science.gov (United States)

McGuire, F; Hegarty, M; Jennings, P; Marsden, P; Smith, L

2017-06-09

Burns and scalds are preventable injuries in children that typically occur in the home. This study aimed to examine the role of hot beverage scalds in paediatric burn admissions in order to identify key target audiences for future safety strategies. Using the Hospital Inpatient Enquiry System (HIPE) a retrospective study of paediatric burn admissions in 2014 examined demographics, cause and severity of injury and location of occurrence. There were 233 paediatric discharges (age 0-18 yrs.) with a principal diagnosis of burn injury; 57% of these occurred in children under three years and 95% of these occurred in the home. Scalds caused 74% of burn injuries; hot beverages accounted for least 33% of these of which 77% were partial thickness and 73% were upper body burns. Effective hot beverage scald prevention strategies, targeted towards caregivers in the home, are required.

Burn Injury Arise From Flying Balloon Toys

Directory of Open Access Journals (Sweden)

Yalcin Kulahci

2007-08-01

Full Text Available Many of peoples are faced minor or major burn injuries in their life. Even the most widespread burn cause is flame injuries, too different burn cause pointed out in literature like Acetylen burns. The cases which imply in literature, mostly causes from explosion of high pressure acetylene tube, metal oxygene patch flame or carbide lamp using from cave explorers. An interesting acetylene burn cause in Turkey was publised by the authors. This cases was to come into being from flying toy balloons flame. 80 person was injured from flying toy ballons flame in a meeting in 2002. Although this potential risks of acetylene, helium have not any of some risk. But helium was provided from other countries and have more price. The injuries which caused from acetylene burns like 1st -2nd degree burns. Consequently that was known helium is more avaliable for using in toy sector, and never cause burn injuries like this. [TAF Prev Med Bull. 2007; 6(4: 291-296

Burn Pit Emissions Exposure and Respiratory and Cardiovascular Conditions Among Airborne Hazards and Open Burn Pit Registry Participants.

Science.gov (United States)

Liu, Jason; Lezama, Nicholas; Gasper, Joseph; Kawata, Jennifer; Morley, Sybil; Helmer, Drew; Ciminera, Paul

2016-07-01

The aim of this study was to determine how burn pit emissions exposure is associated with the incidence of respiratory and cardiovascular conditions. We examined the associations between assumed geographic and self-reported burn pit emissions exposure and respiratory and cardiovascular outcomes in participants of the Airborne Hazards and Open Burn Pit Registry. We found significant dose-response associations for higher risk of self-reported emphysema, chronic bronchitis, or chronic obstructive pulmonary disease with increased days of deployment within 2 miles of selected burn pits (P-trend = 0.01) and self-reported burn pit smoke exposure (P-trend = 0.0005). We found associations between burn pit emissions exposure and higher incidence of post-deployment self-reported respiratory and cardiovascular conditions, but these findings should be interpreted with caution because the surrogate measurements of burn pit emissions exposure in this analysis may not reflect individual exposure levels.

Okanagan indoor wood burning appliance inventory survey

International Nuclear Information System (INIS)

2001-01-01

A survey was conducted to determine the usage and nature of wood burning appliances used by residents in British Columbia's Okanagan region. The objective was to better understand this source of air quality concern and to facilitate strategic planning, guidelines and legislation. The survey also provides a baseline to track the effectiveness of any reduction strategies. It identifies the different types of wood burning appliances used in the community and presents residential options about potential bylaws to protect air quality. The receptivity of households to switch to more efficient wood burning appliances was also examined. The survey completes a portion of an overall emissions inventory for the Okanagan Valley. Environment Canada uses the particulate loading results to model the air quality in the airshed. Results showed that approximately 21 per cent of the households in the Okanagan use indoor wood burning appliances, and burn an average of 2.3 cords of wood each year. Only 11 per cent of the appliances are considered to have advanced burning technology. It is projected that the use of wood burning appliances in the Okanagan will increase by 5 to 7 per cent in the next 2 years. Most residents have good burning habits, but some improvements can still be made. Many residents are considering exchanging old wood burning appliances for clean burning technology appliances for environmental and health reasons. Most households would support a bylaw to control nuisance amounts of smoke from wood burning appliances. 20 tabs., 5 figs

The effect of inhalation aromatherapy with damask rose (Rosa damascena) essence on the pain intensity after dressing in patients with burns: A clinical randomized trial

Science.gov (United States)

Bikmoradi, Ali; Harorani, Mehdi; Roshanaei, Ghodratollah; Moradkhani, Shirin; Falahinia, Golam Hossein

2016-01-01

Background: Pain is one of the common problems encountered by patients with burns, which increases after each dressing. This study aimed to investigate the effect of inhalation aromatherapy with damask rose essence on the pain of patients with burns that is caused after dressing. Materials and Methods: A randomized clinical trial was conducted on 50 patients with second- and third-degree burn wounds. The baseline pain of the patients was assessed 30 min before they entered into the dressing room on the first and second days of intervention. The patients in the experimental group inhaled five drops of damask rose essence 40% in distilled water, while those in the control group inhaled five drops of distilled water as placebo. The pain intensity was assessed using Visual Analogue Scale at 15 and 30 min after the patients exited from the dressing room. Data were analyzed by SPSS (version 18) using descriptive and inferential statistics. Results: There was significant difference between the mean of pain intensity before and after intervention at 15 and 30 min after dressing (P aromatherapy in the experimental group (P aromatherapy with damask rose could be effective for relieving the pain caused after dressing in patients with burns. Therefore, it could be suggested as a complementary therapy in burn patients for pain relief. PMID:27186201

Moving Encounters

Directory of Open Access Journals (Sweden)

Ann Deslandes

2011-04-01

Full Text Available This essay explores my experience of losing an authoritative speaking position – that is, ‘falling on my face’ in a research encounter with the Brazilian Landless Worker’s Movement (O Movimento dos Trabalhadores Rurais sem Terra, or MST.  My specific movements through this locale invoke Gayatri Chakravorty Spivak’s concept of ‘unlearning one’s privilege as a loss’; and Sara Ahmed’s theory of ‘stranger fetishism’.  In writing my brief loss, I also; of course, recover my speaking position, meaning that I can always efface the loss by re-writing it as a source of ethnographic authority.  This essay is written in two voices in order to reflect this paradox: one which describes the encounter, and one that critically ruminates upon it.  I note, for example, that the MST as a variegated conglomerate of people takes the form of particular ‘Others’ when they are represented in the scholarship and polemic of ‘first world’ activists in the so called ‘global justice movement’.  ‘Falling on my face in the street’ of these Others locates particular processes of fetishization within the global justice movement and the relationships across power and difference that are contained herein; processes that impact on the idea of a ‘global’ solidarity against systemic ‘global’ oppressions.

Customer-sales employee encounters: a dyadic perspective.

NARCIS (Netherlands)

Dolen, van W.; Lemmink, J.G.A.M.; Ruyter, de J.C.; Jong, de A.

2003-01-01

Although researchers have suggested that the performance of the salesperson during sales encounters is critical, many of the underlying mechanisms that govern the interaction between salespersons and customers are still unclear. In this research, we investigate sales encounters from a new approach

Apparatus for removing impurities in the sodium of sodium cooled reactors

Energy Technology Data Exchange (ETDEWEB)

Yamauchi, A

1970-11-11

An apparatus is provided for removing oxygen from liquid sodium flowing in a sodium cooled reactor. The removal of oxygen is complete with high efficiency. The liquid sodium to be purified is disposed outside a cylindrical wall and negatively charged, whereas sodium as a reducing material is disposed inside the same wall. The cylindrical wall is made of zirconia-calcia (ZrO/sub 2/)sub(0.87)(CaO)sub(0.13) solid electrolyte, the cylinder having a thickness of 2.5mm, a diameter of 3cm and a depth of 20cm under the sodium level. Electric resistance of the solid electrolyte is 2.3 ohm at 500/sup 0/C. A current of 1A by the application of 25 volts treats 0.3g of oxygen. Consequently, 1 liter or 1kg of liquid sodium containing 1,000ppm of oxygen can be purified for about 3 hours at an electrical consumption of 7.5 watt-hour. In one embodiment, a cylindrical electrolytic solid made of zirconia-calcia or zirconia-yttria was disposed in a container. Liquid sodium containing oxygen flowed outside of the cylinder. Liquid sodium as a reducing material was present inside the cylinder and the container and the cylinder were electrically insulated. An electrode was inserted at the center of the cylinder and a baffle plate at the upper portion of the electrode to shield heat and rising sodium vapor was provided. The space above the container was filled with an inert gas. The oxygen in the liquid sodium to be purified transferred through the wall of the cylinder into the interior of the cylinder so as to oxydize the reducing sodium material. The supersaturated sodium oxide inside the cylinder was deposited.

Burning mouth syndrome

OpenAIRE

Zakrzewska, Joanna; Buchanan, John A. G.

2016-01-01

Burning mouth syndrome is a debilitating medical condition affecting nearly 1.3 million of Americans. Its common features include a burning painful sensation in the mouth, often associated with dysgeusia and xerostomia, despite normal salivation. Classically, symptoms are better in the morning, worsen during the day and typically subside at night. Its etiology is largely multifactorial, and associated medical conditions may include gastrointestinal, urogenital, psychiatric, neurologic and met...

Burning mouth syndrome: An update

Directory of Open Access Journals (Sweden)

Vijay Kumar Ambaldhage

2015-01-01

Full Text Available Burning mouth syndrome (BMS is characterized by an oral burning sensation in the absence of any organic disorders of the oral cavity. Although the cause of BMS is not known, a complex association of biological and psychological factors has been identified, suggesting the existence of a multifactorial etiology. It is observed principally in middle-aged patients and postmenopausal women and is characterized by an intense burning type of pain, preferably on the tongue and in other areas of the oral mucosa. As the symptom of oral burning is seen in various pathological conditions, it is essential for a clinician to be aware of how to differentiate between symptom of oral burning and BMS. This article provides an overview of the literature on this syndrome with special reference to the etiological factors, clinical aspects, diagnostic criteria that should be followed and the therapeutic management with reference to the most recent studies.

Maternal burn-out: an exploratory study.

Science.gov (United States)

Séjourné, N; Sanchez-Rodriguez, R; Leboullenger, A; Callahan, S

2018-02-21

Maternal burn-out is a psychological, emotional and physiological condition resulting from the accumulation of various stressors characterised by a moderate but also a chronic and repetitive dimension. Little research has focused on this syndrome. The current study aims to assess maternal burn-out rate and to identify factors associated with this state of exhaustion. 263 French mothers aged between 20 and 49 years answered five scales quantifying maternal burn-out, perceived social support, parental stress, depression and anxiety symptoms and history of postnatal depression. About 20% of mothers were affected by maternal burn-out. The main factors related to maternal burn-out were having a child perceived as difficult, history of postnatal depression, anxiety, satisfaction of a balance between professional and personal life and parental stress. This research shows the need for further work on maternal burn-out to better understand and prevent this syndrome.

Bacteriological profile of burn wound isolates in a burns center of a tertiary hospital

Directory of Open Access Journals (Sweden)

Amankwa Richcane

2017-01-01

Full Text Available Objective: To determine the bacteriological profile and antimicrobial susceptibility patterns of burn wound isolates.Methods: Swabs were taken from burn wound of patients admitted to Ward D2C and Burns Intensive Care Unit (BICU from December 2014 to November 2015. Samples were processed at the Microbiology Laboratory for identification and sensitivity. Bacteria isolated were identified using their morphological characteristics, Gram staining reaction and biochemical tests. The antimicrobial susceptibility testing was done using Kirby-Bauer disc diffusion method. Questionnaires were also administered to study participants to obtain information on demography, kind of first aid received, antibiotics received prior to culture and sensitivity.Results: A total of 86 patients comprising 45 patients from Ward D2C and 41 from BICU participated in the study. Males were 51(59.3% and females 35 (40.7%. Age of participants ranged from 0–56+ years. Pseudomonas aeruginosa was the commonest pathogen isolated 26(30.2%, followed by Pseudomonas spp. 21(24.4%, Escherichia coli 17(19.8%, Klebsiella spp. 12(14.0%. Coagulase negative Staphylococcus accounted for 2(2.3%. Overall prevalence of infection in the study was 90.7%.Conclusions: Burn wound infection continues to be a major challenge in burn centers. Regular surveillance of commonly identified pathogens in the ward and their antimicrobial susceptibility will guide proper empiric selection of antibiotics for management of burn wounds.

Customer-to-customer roles and impacts in service encounters

OpenAIRE

Lee, Linda

2016-01-01

This thesis investigates customer-to-customer roles and impacts in the context of service encounters. This topic is studied from two angles: customer interactions during group service encounters and customer perceptions post service encounters. The first angle is a focus on group service encounters that addresses the lack of research on customer-to-customer interactions that occur in customer-to-customer interaction-intensive contexts. These are contexts where the interactions between custome...

Pediatric burn rehabilitation: Philosophy and strategies

Directory of Open Access Journals (Sweden)

Shohei Ohgi

2013-09-01

Full Text Available Burn injuries are a huge public health issue for children throughout the world, with the majority occurring in developing countries. Burn injuries can leave a pediatric patient with severely debilitating and deforming contractures, which can lead to significant disability when left untreated. Rehabilitation is an essential and integral part of pediatric burn treatment. The aim of this article was to review the literature on pediatric burn rehabilitation from the Medline, CINAHL, and Web of Science databases. An attempt has been made to present the basic aspects of burn rehabilitation, provide practical information, and discuss the goals and conceptualization of rehabilitation as well as the development of rehabilitation philosophy and strategies.

Effect of sodium lactate /sodium diacetate in combination with sodium nitrite on physiochemical, microbial properties and sensory evaluation of cow sausage

Directory of Open Access Journals (Sweden)

Habib Sedghi

2014-11-01

Full Text Available Sodium nitrite has been always considered as one of the common additives due to its antibacterial effects on Clostridium botulinum and meat products' color, however it produces cancer creating nitrosamine. Recently, organic acids and their salts such as lactates have been employed as antimicrobial compounds. Lactates also improve organileptic properties including color, texture and taste and antioxidant properties. Sodium lactate causes to more reduction of anaerobic spore former bacteria than nitrite, inhibits botulin produced by Clostridium botulinum. Sodium lactate produces a permanent reddish pink color through reduction of deoxymygloboline and producing deoxymyoglobuline. In this study, the decrease of sodium nitrite amount from 120ppm to 15ppm by adding sodium lactate / sodium diacetate led to achieve an acceptable product. The best results revealed through adding 3.0625% of sodium lactate / sodium diacetate in combination with 30ppm sodium nitrite. Results also exhibited more reduction of pathogens' growth than nitrite, enhanced flavor slightly, but unable to produce reddish pink color as produced by nitrite. Results also exhibited that sodium lactate / diacetate cause to retard in microbial growth, reducing chemical change, enhance sensory properties, partially improvement in taste and texture. Although inappropriate color demonstrated sodium lactate / diacetate's inability in red pink color production in 4th sample (contains 15 ppm nitrite, its synergy effect in combination with sodium nitrite on nitroso myoglobuline production has been proven, led to sodium nitrite reduction in sausages.

A Lakatosian Encounter

Science.gov (United States)

Chick, Helen

2010-01-01

There is much to be learned and pondered by reading "Proofs and Refutations," by Imre Lakatos. It highlights the importance of mathematical definitions, and how definitions evolve to capture the essence of the object they are defining. It also provides an exhilarating encounter with the ups and downs of the mathematical reasoning process, where…

Electrolytic process to produce sodium hypochlorite using sodium ion conductive ceramic membranes

Science.gov (United States)

Balagopal, Shekar; Malhotra, Vinod; Pendleton, Justin; Reid, Kathy Jo

2012-09-18

An electrochemical process for the production of sodium hypochlorite is disclosed. The process may potentially be used to produce sodium hypochlorite from seawater or low purity un-softened or NaCl-based salt solutions. The process utilizes a sodium ion conductive ceramic membrane, such as membranes based on NASICON-type materials, in an electrolytic cell. In the process, water is reduced at a cathode to form hydroxyl ions and hydrogen gas. Chloride ions from a sodium chloride solution are oxidized in the anolyte compartment to produce chlorine gas which reacts with water to produce hypochlorous and hydrochloric acid. Sodium ions are transported from the anolyte compartment to the catholyte compartment across the sodium ion conductive ceramic membrane. Sodium hydroxide is transported from the catholyte compartment to the anolyte compartment to produce sodium hypochlorite within the anolyte compartment.

49 CFR 195.226 - Welding: Arc burns.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Welding: Arc burns. 195.226 Section 195.226 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... PIPELINE Construction § 195.226 Welding: Arc burns. (a) Each arc burn must be repaired. (b) An arc burn may...

Festival as embodied encounters

DEFF Research Database (Denmark)

Simonsen, Kirsten; Koefoed, Lasse Martin; Neergaard, Maja de

2017-01-01

This article is part of a project on Paradoxical Spaces: Encountering the Other in public space which explores how cultural difference is experienced, practiced and negotiated in public space. Specifically, it explores the ‘multicultural’ festival Kulturhavn taking place yearly along the harbour...... of Copenhagen. Multicultural festivals are seen as places for on-going identity negotiations, where individuals and groups define meaningful concepts of identity along with notions of exclusion. In the paper, we adopt a performative approach abandoning the distinction between bodies and space and embracing...... ideas of ‘embodiment’ and ‘rhythm’. We explore participant engagement emphasizing bodily practices as well as sensuous experiences, but also differential processes and orientalist images produced in, and through, encounters. Among the range of activities at the festival, we focus on three: food; dance...

DIFFERENTIATING PERIMORTEM AND POSTMORTEM BURNING

Directory of Open Access Journals (Sweden)

Brahmaji Master

2015-01-01

Full Text Available One of the most challenging cases in forensic medicine is ascertaining the cause of death of burnt bodies under suspicious circumstances. The key questions that arise at the time of investigation include: 1  Was the person alive or dead prior to fire accident?  Did the victim die because of burn?  If death was not related to burns, could burns play a role in causing death?  Were the burns sustained accidentally, did the person commit suicide or was the person murdered?  Are the circumstances suggesting an attempt to conceal crime?  How was the fire started?  How was the victim identified?  In case of mass fatalities, who died first? Postmortem burning of corpses is supposed to be one of the ways to hide a crime. Differentiating the actual cause of death in burn patients is therefore important. Medical examiners usually focus on the defining the changes that occur in tissues while forensic anthropologists deal with the changes related to the bone with or without any the influence of other tissues. Under the circumstances of fire, differentiating the perimortem trauma from that of postmortem cause of bone fractures is vital in determining the cause and motive of death

Comparison of heat transfer and soil impacts of air curtain burner burning and slash pile burning

Science.gov (United States)

Woongsoon Jang; Deborah S. Page-Dumroese; Han-Sup Han

2017-01-01

We measured soil heating and subsequent changes in soil properties between two forest residue disposal methods: slash pile burning (SPB) and air curtain burner (ACB). The ACB consumes fuels more efficiently and safely via blowing air into a burning container. Five burning trials with different fuel sizes were implemented in northern California, USA. Soil temperature...

Pediatric burn wound impetigo after grafting.

Science.gov (United States)

Aikins, Kimberly; Prasad, Narayan; Menon, Seema; Harvey, John G; Holland, Andrew J A

2015-01-01

Modern burn care techniques have reduced the risk of infection of the acute burn wound, resulting in more rapid healing and a lower incidence of graft loss. Secondary breakdown may still occur. The loss of epithelium in association with multifocal superficial abscesses and ulceration has been termed burns impetigo. This may result in considerable morbidity and require prolonged treatment. The events preceding development, the impact on the patient, and the ideal treatment appear unclear and poorly reported. In 5 years, between 2006 and 2011, 406 pediatric burns were treated with skin grafts, with 7% developing burns impetigo. Time to resolution ranged from 5 to 241 days: the mean time to complete healing was greatest with conservative management (96 days), followed by antibacterial dressings (37 days), oral antibiotics (36 days), topical steroids (16 days), and oral antibiotics in combination with topical steroids (13.5 days). Burns impetigo resulted in significant morbidity, requiring multiple visits to the treatment center and prolonged symptoms. Delay in diagnosis and treatment resulted in worse outcomes. Prompt consideration of burns impetigo should occur when postgraft patients present with suggestive clinical signs and treatment with oral antibiotics plus topical steroids should be considered.

[Burns, new challenges to take on].

Science.gov (United States)

Galí-Llàcer, Rosa; Sena-Fernández, Beatriz; Leyva-Moral, Juan Manuel

2009-04-01

This article concerns a transversal descriptive study which shows the characteristics of burns treated in a Primary Health Care Center in an urban environment in Barcelona from 19 July 2005 unti 11 August 2007 (N=93). Patients younger than 15 were excluded from this study. 88% (82; CI of 95% 81,47-94,59) of the burns treated were caused by a thermal agent. Kitchen cooking oil ranks first as the cause of burns (24; 27%, CI of 95% 17,99-36,01). 70% of the burns studied had signs of superficial skin damage (65, CI of 95% 60,70-79,30). 61% (57; CI of 95% 51,70-70,30) of these burns were located on upper extremities The average recorded body surface burned was 0.0076% (median = 0,005%, range = 0,0001-0,5000%). The greatest number of wounds were observed among men aged 31 to 45 (17%; 16; CI of 95% 9,38-24,62). Educational health programs which focus on prevention of, and first aid care for, burns are needed. Studies like this one may prove useful when starting preventive or educational strategies.

Burning characteristics of microcellular combustible objects

Directory of Open Access Journals (Sweden)

Wei-tao Yang

2014-06-01

Full Text Available Microcellular combustible objects for application of combustible case, caseless ammunition or combustible detonator-holding tubes are fabricated through one-step foaming process, in which supercritical CO2 is used as foaming agent. The formulations consist of inert polymer binder and ultra fine RDX. For the inner porous structures of microcellular combustible objects, the cell sizes present a unimodal or bimodal distribution by adjusting the foaming conditions. Closed bomb test is to investigate the influence of both porous structure style and RDX content on burning behavior. The sample with bimodal distribution of cell sizes burns faster than that with unimodal distribution, and the concentration of RDX can influence the burning characteristics in a positive manner. In addition, the translation of laminar burning to convective burning is determined by burning rate versus pressure curves of samples at two different loading densities, and the resulting transition pressure is 30 MPa. Moreover, the samples with bigger sample size present higher burning rate, resulting in providing deeper convective depth. Dynamic vivacity of samples is also studied. The results show that the vivacity increases with RDX content and varies with inner structure.

[Burns in adolescents].

Science.gov (United States)

Ortiz Rodríguez, R; Domínguez Amillo, E; Soto Beauregard, C; Díaz González, M; López Gutiérrez, J C; Ros Mar, Z; Tovar Larrucea, J A

2012-04-01

The aim of this study was to know the epidemiology of burns in teenagers. Burn patients over 11 years old admitted in our Institution in the last 10 years were included. Etiology, burn size, hospital stay, quirurgical interventions and long term sequelae were registered. One thousand and eight patients were admitted, 89 were over 11 years (8.8%), 70.7% were boys and 29.3% girls. Fire was the principal agent in 58 cases (65.1%), due to fireworks in 13 (22.4%), alcohol in 7 (12%), explosion of flammable containers (spray) in 4 (6.8%) and gasoline in 3 (5.2%). Fireworks injuries and spray explosions affected face and hand in 88% cases. The median hospital stay was 8 days after admission (1 to 90). 83.1% required surgical treatment with mean of 1.8 +/- 1.4 interventions and 21.3% had long-term sequelaes that required at least one surgical intervention. Fire is the main cause of burns in adolescents. Fireworks injuries represented a quarter of that lesions, and highlights paint spray explosions as new causative agents. Considering the high morbidity in this age group, with permanent functional and aesthetic sequelae, prevention campaigns are needed to reduce such accidents.

A core design study for 'zero-sodium-void-worth' cores

International Nuclear Information System (INIS)

Kawashima, Masatoshi; Suzuki, Masao; Hill, R.N.

1992-01-01

Recently, a number of low sodium-void-worth metal-fueled core design concepts have been proposed; to provide for flexibility in transuranic nuclide management strategy, core designs which exhibit a wide range of breeding characteristics have been developed. Two core concepts, a flat annular (transuranic burning) core and an absorber-type parfait (transuranic self-sufficient) core, are selected for this study. In this paper, the excess reactivity management schemes applied in the two designs are investigated in detail. In addition, the transient effect of reactivity insertions on the parfait core design is assessed. The upper and lower core regions in the parfait design are neutronically decoupled; however, the common coolant channel creates thermalhydraulic coupling. This combination of neutronic and thermalhydraulic characteristics leads to unique behavior in anticipated transient overpower events. (author)

Impact of Work-Related Burn Injury on Social Reintegration Outcomes: A Life Impact Burn Recovery Evaluation (LIBRE) Study.

Science.gov (United States)

Schneider, Jeffrey C; Shie, Vivian L; Espinoza, Leda F; Shapiro, Gabriel D; Lee, Austin; Acton, Amy; Marino, Molly; Jette, Alan; Kazis, Lewis E; Ryan, Colleen M

2017-11-26

To examine differences in long-term social reintegration outcomes for burn survivors with and without work-related injuries. Cross-sectional survey. Community-dwelling burn survivors. Burn survivors (N=601) aged ≥18 years with injuries to ≥5% total body surface area or burns to critical areas (hands, feet, face, or genitals). Not applicable. The Life Impact Burn Recovery Evaluation Profile was used to examine the following previously validated 6 scale scores of social participation: Family and Friends, Social Interactions, Social Activities, Work and Employment, Romantic Relationships, and Sexual Relationships. Older participants, those who were married, and men were more likely to be burned at work (Preintegration outcomes than those without work-related injuries. Identification of those at higher risk for work reintegration challenges after burn injury may enable survivors, providers, employers, and insurers to better use appropriate resources to promote and target optimal employment outcomes. Copyright © 2017 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Burn prevention in Zambia: a targeted epidemiological approach.

Science.gov (United States)

Heard, Jason P; Latenser, Barbara A; Liao, Junlin

2013-01-01

The aim of this study is to assess primary burn prevention knowledge in a rural Zambian population that is disproportionately burdened by burn injuries. A 10-question survey was completed by youths, and a 15-question survey was completed by adults. The survey was available in both English and Nyanja. The surveys were designed to test their knowledge in common causes, first aid, and emergency measures regarding burn injuries. Logistic regression analysis was used to explore relationships between burn knowledge, age, school, and socioeconomic variables. A burn prevention coloring book, based on previous local epidemiological data, was also distributed to 800 school age youths. Five hundred fifty youths and 39 adults completed the survey. The most significant results show knowledge deficits in common causes of burns, first aid treatment of a burn injury, and what to do in the event of clothing catching fire. Younger children were more likely to do worse than older children. The adults performed better than the youths, but still lack fundamental burn prevention and treatment knowledge. Primary burn prevention data from the youths and adults surveyed demonstrate a clear need for burn prevention and treatment education in this population. In a country where effective and sustainable burn care is lacking, burn prevention may be a better investment to reduce burn injury than large investments in healthcare resources.

Accelerant-related burns and drug abuse: Challenging combination.

Science.gov (United States)

Leung, Leslie T F; Papp, Anthony

2018-05-01

Accelerants are flammable substances that may cause explosion when added to existing fires. The relationships between drug abuse and accelerant-related burns are not well elucidated in the literature. Of these burns, a portion is related to drug manufacturing, which have been shown to be associated with increased burn complications. 1) To evaluate the demographics and clinical outcomes of accelerant-related burns in a Provincial Burn Centre. 2) To compare the clinical outcomes with a control group of non-accelerant related burns. 3) To analyze a subgroup of patients with history of drug abuse and drug manufacturing. Retrospective case control study. Patient data associated with accelerant-related burns from 2009 to 2014 were obtained from the British Columbia Burn Registry. These patients were compared with a control group of non-accelerant related burns. Clinical outcomes that were evaluated include inhalational injury, ICU length of stay, ventilator support, surgeries needed, and burn complications. Chi-square test was used to evaluate categorical data and Student's t-test was used to evaluate mean quantitative data with the p value set at 0.05. A logistic regression model was used to evaluate factors affecting burn complications. Accelerant-related burns represented 28.2% of all burn admissions (N=532) from 2009 to 2014. The accelerant group had higher percentage of patients with history of drug abuse and was associated with higher TBSA burns, ventilator support, ICU stay and pneumonia rates compared to the non-accelerant group. Within the accelerant group, there was no difference in clinical outcomes amongst people with or without history of drug abuse. Four cases were associated with methamphetamine manufacturing, all of which underwent ICU stay and ventilator support. Accelerant-related burns cause significant burden to the burn center. A significant proportion of these patients have history of drug abuse. Copyright © 2017 Elsevier Ltd and ISBI. All rights

Childhood burns in south eastern Nigeria.

Science.gov (United States)

Archibong, A E; Antia, U E; Udosen, J

1997-06-01

In a ten year retrospective study of burns in children in University of Calabar Teaching Hospital (UCTH), Calabar, the main causes were hot water, hot soup or oil (56.6%) involving children mostly in the one to three year age group. The relative safety of the home environment seen in other forms of paediatric trauma is not observed in burns in children. A changing pattern of burns in children has emerged within the region with naked flames/bush fire coming second and affecting 22.7% of the children. Chemical burns hitherto a rare occurrence is now frequent because of the storage of caustic soda and acids in living rooms by soap making parents. Burns affecting the perineum, axilla and buttocks are difficult to keep clean and frequently lead to infections, with associated increased morbidity. Causes of childhood burns are largely preventable requiring active social/medical education and public enlightenment campaigns on the various methods of prevention.

In-Situ Burn Gaps Analysis

Science.gov (United States)

2015-02-01

This Report) UNCLAS//Public 20. Security Class (This Page) UNCLAS//Public 21. No of Pages 76 22. Price UNCLAS//Public | CG-926 RDC | Merrick...surveillance and spotting techniques/equipment to keep responders in the heaviest oil concentrations where their operation to skim , burn, or disperse...Offshore Oil Skim And Burn System For Use With Vessels Of Opportunity. UNCLAS//Public | CG-926 RDC | Merrick, et al. Public | June 2015 In-Situ Burn Gaps

Ileocolic Perforation Secondary to Sodium Polystyrene Sulfonate in Sorbitol Use: A Case Report

Directory of Open Access Journals (Sweden)

Vincent Trottier

2009-01-01

Full Text Available Hyperkalemia is a common condition encountered in medical and surgical patients. It can lead to various complications including cardiac arrhythmias. Sodium polystyrene sulfonate (SPS in sorbitol is an ion-exchange resin that can be used to treat hyperkalemia. It can be used in enema or in oral form. The present article describes the case of an intensive care unit patient who experienced severe, diffuse, intestinal perforation induced by the use of SPS-sorbitol, requiring multiple laparotomies, followed by a brief review of the relevant literature and recommendations regarding the use of SPS-sorbitol.

Sodium-cooled fast reactor core designs for transmutation of MHR spent fuel

International Nuclear Information System (INIS)

Hong, S. G.; Kim, Y. H.; Venneri, F.

2010-01-01

In this paper, the core design analyses of sodium cooled fast reactors (SFR) are performed for the effective transmutation of the DB (Deep Burn)-MHR (Modular Helium Reactor). In this concept, the spent fuels of DB-MHR are transmuted in SFRs with a closed fuel cycle after TRUs from LWR are first incinerated in a DB-MHR. We introduced two different type SFR core designs for this purpose, and evaluated their core performance parameters including the safety-related parameters. In particular, the cores are designed to have lower transmutation rate relatively to our previous work so as to make the fuel characteristics more feasible. The first type cores which consist of two enrichment regions are typical homogeneous annular cores and they rate 900 MWt power. On the other hand, the second type cores which consist of a central non-fuel region and a single enrichment fuel region rate relatively higher power of 1500 MWt. For these cores, the moderator rods (YH 1.8 ) are used to achieve less positive sodium void worth and the more negative Doppler coefficient because the loading of DB-MHR spent fuel leads to the degradation of these safety parameters. The analysis results show that these cores have low sodium void worth and negative reactivity coefficients except for the one related with the coolant expansion but the coolant expansion reactivity coefficient is within the typical range of the typical SFR cores. (authors)

Report of sodium cavitation

International Nuclear Information System (INIS)

Murai, Hitoshi; Shima, Akira; Oba, Toshisaburo; Kobayashi, Ryoji; Hashimoto, Hiroyuki

1975-01-01

The damage of components for LMFBRs due to sodium cavitation is serious problem. This report summarizes the following items, (1) mechanism of the incipience of sodium cavitation, (2) damage due to sodium cavitation, (3) detection method for sodium cavitation, and (4) estimation method for sodium cavitation by the comparison with water cavitation. Materials were collected from the reports on liquid metal cavitation, sodium cavitation and water cavitation published from 1965 to now. The mechanism of the incipience of sodium cavitation cavitation parameters (mean location, distributed amount or occurrence aspect and stability), experiment of causing cavitation with Venturi tube, and growth of bubbles within superheated sodium. The sodium cavitation damage was caused by magnetostriction vibration method and with Venturi tube. The state of damage was investigated with the cavitation performance of a sodium pump, and the damage was examined in view of the safety of LMFBR plants. Sodium cavitation was detected with acoustic method, radiation method, and electric method. The effect of physical property of liquid on incipient cavitation was studied. These are thermodynamic effect based on quasistatic thermal equilibrium condition and the effect of the physical property of liquid based on bubble dynamics. (Iwase, T.)

Microbiological and quantitative analysis of burn wounds in the burn unit at a tertiary care hospital in Kashmir

Directory of Open Access Journals (Sweden)

Tahir Saleem Khan

2016-01-01

Full Text Available Background: The burn wound represents a susceptible site for opportunistic colonization by organisms of endogenous and exogenous origin. The present study was undertaken to analyze the microflora of burn wounds of the burn patients from a tertiary care hospital in Kashmir, India. Materials sand Methods: The study included all patients with acute burns admitted from January 2010 to December 2011 (2 years. The standard techniques, as practiced during collection of microbiological specimens, were used during wound swab/biopsy collection. Results: 74.19% of swab cultures yielded single isolates. On swab culture, Pseudomonas aeruginosa was the commonly isolated organism (46.86%. Staphylococcus aureus was the most common isolate isolated during 1st postburn week (30.86%. 258/288 (89.58% blood cultures were sterile. 8/58 (13.79% blood cultures were positive during the second postburn week. S. aureus was the most common organism grown on blood culture (44.44%. P. aeruginosa was mostly sensitive to polymyxin B (86.0%, amikacin (40.0%, and ciprofloxacin (37.3%, respectively. S. aureus was most commonly sensitive to linezolid (85.0% and vancomycin (78.8%% whereas Acinetobacter spp. was sensitive to polymyxin B (65.3%, piperacillin/tazobactam (44.9%, and amikacin (38.8%. Patients (27.27% who showed local signs of burn wound infection and positive blood culture were subjected to burn wound biopsy. 93.33% of patients who had counts >105 colony-forming unit/g of tissue showed significant association with local signs of burn wound infection and positive blood culture for any organism. Conclusion: The microbiological surveillance of burn wounds needs to be continued for a rational antibiotic policy and prevention of emergence of resistant organisms. Burn wound biopsy culture is an effective tool for quantitative analysis of burn wounds; however, subjecting this biopsy to histological examination is more predictable of burn wound infection and its correlation

A multi-sensor burned area algorithm for crop residue burning in northwestern India: validation and sources of error

Science.gov (United States)

Liu, T.; Marlier, M. E.; Karambelas, A. N.; Jain, M.; DeFries, R. S.

2017-12-01

A leading source of outdoor emissions in northwestern India comes from crop residue burning after the annual monsoon (kharif) and winter (rabi) crop harvests. Agricultural burned area, from which agricultural fire emissions are often derived, can be poorly quantified due to the mismatch between moderate-resolution satellite sensors and the relatively small size and short burn period of the fires. Many previous studies use the Global Fire Emissions Database (GFED), which is based on the Moderate Resolution Imaging Spectroradiometer (MODIS) burned area product MCD64A1, as an outdoor fires emissions dataset. Correction factors with MODIS active fire detections have previously attempted to account for small fires. We present a new burned area classification algorithm that leverages more frequent MODIS observations (500 m x 500 m) with higher spatial resolution Landsat (30 m x 30 m) observations. Our approach is based on two-tailed Normalized Burn Ratio (NBR) thresholds, abbreviated as ModL2T NBR, and results in an estimated 104 ± 55% higher burned area than GFEDv4.1s (version 4, MCD64A1 + small fires correction) in northwestern India during the 2003-2014 winter (October to November) burning seasons. Regional transport of winter fire emissions affect approximately 63 million people downwind. The general increase in burned area (+37% from 2003-2007 to 2008-2014) over the study period also correlates with increased mechanization (+58% in combine harvester usage from 2001-2002 to 2011-2012). Further, we find strong correlation between ModL2T NBR-derived burned area and results of an independent survey (r = 0.68) and previous studies (r = 0.92). Sources of error arise from small median landholding sizes (1-3 ha), heterogeneous spatial distribution of two dominant burning practices (partial and whole field), coarse spatio-temporal satellite resolution, cloud and haze cover, and limited Landsat scene availability. The burned area estimates of this study can be used to build

Total-body sodium and sodium excess

International Nuclear Information System (INIS)

Aloia, J.F.; Cohn, S.H.; Abesamis, C.; Babu, T.; Zanzi, I.; Ellis, K.

1980-01-01

Total-body levels of sodium (TBNa), chlorine (TBCI), calcium (TBCa), and potassium (TBK) were measured by neutron activation and analysis of results by whole body counting in 66 postmenopausal women. The relationship between TBNa, and TBCl, TBK, and TBCa on the one hand, and height and weight on the other, were found to compare with those previously reported. The hypothesis that TBNa and TBCl are distributed normally could not be rejected. The sodium excess (Na/sub es/) is defined as the sodium that is present in excess of that associated with the extracellular fluid (chlorine) space; the Na/sub es/ approximates nonexchangeable bone sodium. In these 66 postmenopausal women, and in patients with different endocrinopathies previously described, the values on Na/sub es/ did not differ from the normal values except in the thyrotoxicosis patients, where they were decreased. A close relationship between Na/sub es/ and TBCa was maintained in the endocrinopathies studied. This relationship was found in conditions accompanied by either an increment or a loss of skeletal mass. It appears that the NA/sub es/ value is primarily dependent upon the calcium content of bone

PROSCARA Inc. in-situ burning summary paper

International Nuclear Information System (INIS)

1994-06-01

In-situ burning as a viable response tactic in the event of an oil spill, was discussed. Key factors which influence a decision to use burning were enumerated, including a detailed analysis of the environmental effects of in-situ burning on soils. The critical parameters were time, soil heating and extent of oil penetration into the soil. It was noted that on water-saturated and frozen soil in-situ burning had no adverse effects. The advantages and disadvantages of in-situ burning vis-a-vis conventional mechanical recovery were discussed. Factors that do, and factors that do not support decisions in favour of in-situ burning were listed. 4 refs., 2 tabs

Reactive burn models and ignition & growth concept

Directory of Open Access Journals (Sweden)

Shaw M.S.

2011-01-01

Full Text Available Plastic-bonded explosives are heterogeneous materials. Experimentally, shock initiation is sensitive to small amounts of porosity, due to the formation of hot spots (small localized regions of high temperature. This leads to the Ignition & Growth concept, introduced by LeeTarver in 1980, as the basis for reactive burn models. A homo- genized burn rate needs to account for three meso-scale physical effects: (i the density of active hot spots or burn centers; (ii the growth of the burn fronts triggered by the burn centers; (iii a geometric factor that accounts for the overlap of deflagration wavelets from adjacent burn centers. These effects can be combined and the burn model defined by specifying the reaction progress variable λ = g(s as a function of a dimensionless reaction length s(t = rbc/ℓbc, rather than by specifying an explicit burn rate. The length scale ℓbc(Ps = [Nbc(Ps]−1/3 is the average distance between burn centers, where Nbc is the number density of burn centers activated by the lead shock. The reaction length rbc(t = ∫t0 D(P(t′dt′ is the distance the burn front propagates from a single burn center, where D(P is the deflagration speed as a function of the local pressure and t is the time since the shock arrival. A key implementation issue is how to determine the lead shock strength in conjunction with a shock capturing scheme. We have developed a robust algorithm for this purpose based on the Hugoniot jump condition for the energy. The algorithm utilizes the time dependence of density, pressure and energy within each cell. The method is independent of the numerical dissipation used for shock capturing. It is local and can be used in one or more space dimensions. The burn model has a small number of parameters which can be calibrated to fit velocity gauge data from shock initiation experiments.

Tourniquet associated chemical burn

Directory of Open Access Journals (Sweden)

Jae-Hyuk Yang

2012-01-01

Full Text Available Chemical burn under pneumatic tourniquet is an iatrogenic preventable injury and is rarely reported in the literature. The two important mechanisms are maceration (friction and wetness underneath the tourniquent. In this report, our experience with two illustrative patients who presented with iatrogenic tourniquet associated burn is described.

Drug utilization study in a burn care unit of a tertiary care hospital

Directory of Open Access Journals (Sweden)

Santoshkumar R Jeevangi

2011-03-01

Full Text Available Objective: To evaluate drug utilization and associated costs for the treatment of patients admitted in burn care unit of a tertiary care hospital. Methods: A prospective cross sectional study was conducted for a period of 15 months at Basaweshwara Teaching and General Hospital (BTGH, Gulbarga and the data collected was analyzed for various drug use indicators. Results: A total of 100 prescriptions were collected with 44% belonging to males and 56% to females. The average number of drugs per prescription ranged from 4.5 to 9.5. 9.5% of generics and 92% of essential drugs were prescribed. The opioid analgesics and sedatives were prescribed to all the patients who were admitted in burn care unit. The (Defined daily dose DDD/1 000/day for amikacin (359 was the highest followed by diclofenac sodium (156, pantoprazole (144, diazepam (130, ceftazidime (124, tramadol (115, ceftriaxone (84 and for paracetamol (4 which was the lowest. Conclusions: Significant amount of the money was spent on procurement of drugs. Most of the money was spent on prescribed antibiotics. The prescription of generic drugs should be promoted, for cost effective treatment. Hence the results of the present study indicate that there is a considerable scope for improvement in the prescription pattern.

Sodium fluxes in sweet pepper exposed to varying sodium concentrations

NARCIS (Netherlands)

Blom-Zandstra, M.; Vogelzang, S.A.; Veen, B.W.

1998-01-01

The sodium transport and distribution of sweet pepper (Capsicum annuum L.) under saline conditions were studied after transferring the plants to a sodium-free nutrient solution. Sodium stress up to 60 mM did not affect the growth of sweet pepper, as it appears able to counteract the unfavourable

Suicide by burning: epidemiological and clinical profiles.

Science.gov (United States)

Theodorou, Panagiotis; Phan, Vu T Q; Weinand, Christian; Maegele, Marc; Maurer, Christoph A; Perbix, Walter; Leitsch, Sebastian; Lefering, Rolf; Spilker, Gerald

2011-04-01

Self-immolation constitutes a rare form of suicide in developed countries, though it accounts for unique injury characteristics in the burn intensive care unit. The aim of this study was to present the epidemiological and clinical features of patients burned during a suicidal attempt seen in a North Rhine-Westphalia burn intensive care unit (BICU). To address this aim, we undertook a 21-year retrospective study involving patients with thermal injuries admitted to the largest burn unit in Germany. A total of 125 suicide-related burn victims were identified in the study period (9.4%). Comparing the self-immolation group with the rest burn patient cohort, suicide victims were more likely to be single and to act under the influence of alcohol. The suicidal group had a larger extent of burns, higher incidence of inhalation injury, required more surgical procedures, catecholamines, blood transfusions, and a longer BICU stay. Their clinical course was complicated by prolonged intubation period, higher rate of multiple drug-resistant bacteria acquisition and sepsis, leading to a higher mortality rate. Although the proportion of self-immolation victims among all burned patients is not high, the markedly higher severity of their burns and their poorer quality of outcomes makes them an important clinical subgroup for further study.

Reaction velocity of sodium hydration in humid air and sodium carbonation in humid carbon dioxide atmosphere. Fundamental study on sodium carbonate process in FBR bulk sodium coolant disposal technology

International Nuclear Information System (INIS)

Tadokoro, Yutaka; Yoshida, Eiichi

1999-11-01

A sodium carbonate processing method, which changes sodium to sodium carbonate and/or sodium bicarbonate by humid carbon dioxide, has been examined and about to be applied to large test loops dismantling. However, that the basic data regarding the progress of the reaction is insufficient on the other hand, is a present condition. The present report therefore aims at presenting basic data regarding the reaction velocity of sodium hydration in humid air and sodium carbonation in humid carbon dioxide atmosphere, and observing the reaction progress, for the application to large test loops dismantling. The test result is summarized as follows. (1) Although the reaction velocity of sodium varied with sodium specimen sizes and velocity measurement methods, the reaction velocity of sodium hydration was in about 0.16 ∼ 0.34 mmh -1 (0.016 ∼ 0.033g cm -2 h -1 , 6.8x10 -4 ∼ 1.4x10 -3 mol cm -2 h -1 ) and that of sodium carbonation was in about 0.16 ∼ 0.27mmh -1 (0.016 ∼ 0.023g cm -2 h -1 , 6.8x10 -4 ∼ 1.1x10 -3 mol cm -2 h -1 ) (26 ∼ 31degC, RH 100%). (2) The reaction velocity of sodium in carbon dioxide atmosphere was greatly affected by vapor partial pressure (absolutely humidity). And the velocity was estimated in 0.08 ∼ 0.12mmh -1 (0.008 ∼ 0.012g cm -2 h -1 , 3.4x10 -4 ∼ 5.2x10 -4 mol cm -2 h -1 ) in the carbon dioxide atmosphere, whose temperature of 20degC and relative humidity of 80% are assumed real sodium carbonate process condition. (3) By the X-ray diffraction method, NaOH was found in humid air reaction product. Na 2 CO 3 , NaHCO 3 were found in carbon dioxide atmosphere reaction product. It was considered that Sodium changes to NaOH, and subsequently to NaHCO 3 through Na 2 CO 3 . (4) For the application to large test loops dismantling, it is considered possible to change sodium to a target amount of sodium carbonate (or sodium bicarbonate) by setting up gas supply quantity and also processing time appropriately according to the surface area

Co-creation of Innovations in ICT based service encounters

DEFF Research Database (Denmark)

Sørensen, Jannick Kirk; Henten, Anders

2014-01-01

Innovations in services often emanate from service encounters (i.e. the touch points between the service producers and the customers). Two different types of service encounters are dealt with: face-to-face and ICT-based service encounters. The aim of the chapter is to examine the specific...

Sodium intake and dietary sources of sodium in undergraduate students from Novi Sad, Serbia

Directory of Open Access Journals (Sweden)

Jovičić-Bata Jelena

2016-01-01

Full Text Available Background/Aim. Data on sodium intake and sources of sodium in the diet in Serbia are limited. The aim of this study was to estimate the sodium intake and identify the sources of sodium in the diet of undergraduate students attending the University of Novi Sad. Methods. Students completed a questionnaire to gather data on their gender, age and university faculty attended, and then a 24 h dietary recall. The sodium intake of the students was calculated using the dietary recall data and data on the sodium content of foods. The contribution of different food groups as well as of specific foodstuffs to the total sodium intake was calculated. Results. The mean estimated sodium intake of the students was 3,938.5 ± 1,708.1 mg/day. The sodium intake of 89.1% of the surveyed students exceeded the guideline for sodium intake, the majority of the sodium coming from processed foods (78.9% of the total sodium intake. The food groups that contributed the most to the total sodium intake of the students were meat and meat products (21.7% and cereals and cereal-based products (18.6%. Bread and other bakery products were responsible for 13.1% of the total sodium intake. Conclusion. High sodium intake in students of the University of Novi Sad puts them at high risk of developing high blood pressure. The food industry should work towards reformulating products with high sodium content, especially bread and other bakery products. Efforts should be taken to reduce sodium intake among undergraduate students in Novi Sad.

Burning mouth syndrome: An update

OpenAIRE

Vijay Kumar Ambaldhage; Jaishankar Homberhalli Puttabuddi; Purnachandrarao Naik Nunsavath

2015-01-01

Burning mouth syndrome (BMS) is characterized by an oral burning sensation in the absence of any organic disorders of the oral cavity. Although the cause of BMS is not known, a complex association of biological and psychological factors has been identified, suggesting the existence of a multifactorial etiology. It is observed principally in middle-aged patients and postmenopausal women and is characterized by an intense burning type of pain, preferably on the tongue and in other areas of the ...

Parametric Effect of Sodium Hydroxide and Sodium Carbonate on the Potency of a Degreaser

OpenAIRE

Babatope Abimbola Olufemi

2016-01-01

Experimental and statistical analysis was carried out on the comparative effect of sodium hydroxide and sodium carbonate on the potency of a laboratory produced degreaser in this work. The materials used include; octadecyl benzene sulphonic acid, sodium hydroxide, sodium carbonate, sodium metasilicate, carboxyl methyl cellulose (C.M.C), formadelhyde, perfume, colourant and distilled water. Different samples of degreaser were produced with varying composition of sodium hydroxide and sodium car...

Test Your Sodium Smarts

Science.gov (United States)

... You may be surprised to learn how much sodium is in many foods. Sodium, including sodium chloride ... foods with little or no salt. Test your sodium smarts by answering these 10 questions about which ...

Stress disorder and PTSD after burn injuries: a prospective study of predictors of PTSD at Sina Burn Center, Iran

Directory of Open Access Journals (Sweden)

Sadeghi-Bazargani H

2011-07-01

Full Text Available Homayoun Sadeghi-Bazargani1, Hemmat Maghsoudi2, Mohsen Soudmand-Niri3, Fatemeh Ranjbar4, Hossein Mashadi-Abdollahi51Neuroscience Research Center, Statistics and Epidemiology Department, School of Health and Nutrition, 2Department of Surgery, 3School of Psychology, 4Department of Psychiatry, 5National Public Health Management Centre, Tabriz University of Medical Sciences, Tabriz, IranBackground: A burn injury can be a traumatic experience with tremendous social, physical, and psychological consequences. The aim of this study was to investigate the existence of post-traumatic stress disorder (PTSD and predictors of PTSD Checklist score initially and 3 months after injury in burns victims admitted to the Sina Burn Center in north-west Iran.Methods: This prospective study examined adult patients aged 16–65 years with unintentional burns. The PTSD Checklist was used to screen for PTSD.Results: Flame burns constituted 49.4% of all burns. Mean PTSD score was 23.8 ± 14.7 early in the hospitalization period and increased to 24.2 ± 14.3, 3 months after the burn injury. Twenty percent of victims 2 weeks into treatment had a positive PTSD screening test, and this figure increased to 31.5% after 3 months. The likelihood of developing a positive PTSD screening test increased significantly after 3 months (P < 0.01. Using multivariate regression analysis, factors independently predicting PTSD score were found to be age, gender, and percentage of total body surface area burned.Conclusion: PTSD was a problem in the population studied and should be managed appropriately after hospital admission due to burn injury. Male gender, younger age, and higher total body surface area burned may predict a higher PTSD score after burn injury. Keywords: post-traumatic stress disorder, burn injury, predictors, Iran

Comparison of KANEXT and SERPENT for fuel depletion calculations of a sodium fast reactor

International Nuclear Information System (INIS)

Lopez-Solis, R.C.; Francois, J.L.; Becker, M.; Sanchez-Espinoza, V.H.

2014-01-01

As most of Generation-IV systems are in development, efficient and reliable computational tools are needed to obtain accurate results in reasonably computer time. In this study, KANEXT code system is presented and validated against the well-known Monte Carlo SERPENT code, for fuel depletion calculations of a sodium fast reactor (SFR). The KArlsruhe Neutronic EXtended Tool (KANEXT) is a modular code system for deterministic reactor calculations, consisting of one kernel and several modules. Results obtained with KANEXT for the SFR core are in good agreement with the ones of SERPENT, e.g. the neutron multiplication factor and the isotopes evolution with burn-up. (author)

Vaporization order and burning efficiency of crude oils during in-situ burning on water

DEFF Research Database (Denmark)

van Gelderen, Laurens; Malmquist, Linus M.V.; Jomaas, Grunde

2017-01-01

furthermore showed that the vaporization was diffusion-limited. Analysis of the heat transfer balance for the crude oils indicated that the energy available for evaporation decreased over time due to increasing heat losses, which were caused by the volatility controlled vaporization order. Presumably, larger......In order to improve the understanding of the burning efficiency and its observed size dependency of in-situ burning of crude oil on water, the vaporization order of the components in crude oils was studied. The vaporization order of such multicomponent fuels was assessed by studying the surface...... these results. The crude oils did not show any steady state behavior, but instead had an increasing surface temperature and decreasing burning rate and flame height, indicating a volatility controlled vaporization order. An increasing concentration gradient from the medium to heavy fraction in the burn residues...

Acute pain management in burn patients

DEFF Research Database (Denmark)

Gamst-Jensen, Hejdi; Vedel, Pernille Nygaard; Lindberg-Larsen, Viktoria Oline

2014-01-01

OBJECTIVE: Burn patients suffer excruciating pain due to their injuries and procedures related to surgery, wound care, and mobilization. Acute Stress Disorder, Post-Traumatic Stress Disorder, chronic pain and depression are highly prevalent among survivors of severe burns. Evidence-based pain...... patients. The most highly recommended guidelines provided clear and accurate recommendations for the nursing and medical staff on pain management in burn patients. We recommend the use of a validated appraisal tool such as the AGREE instrument to provide more consistent and evidence-based care to burn...

National programme for prevention of burn injuries

Directory of Open Access Journals (Sweden)

Gupta J

2010-10-01

Full Text Available The estimated annual burn incidence in India is approximately 6-7 million per year. The high incidence is attributed to illiteracy, poverty and low level safety consciousness in the population. The situation becomes further grim due to the absence of organized burn care at primary and secondary health care level. But the silver lining is that 90% of burn injuries are preventable. An initiative at national level is need of the hour to reduce incidence so as to galvanize the available resources for more effective and standardized treatment delivery. The National Programme for Prevention of Burn Injuries is the endeavor in this line. The goal of National programme for prevention of burn injuries (NPPBI would be to ensure prevention and capacity building of infrastructure and manpower at all levels of health care delivery system in order to reduce incidence, provide timely and adequate treatment to burn patients to reduce mortality, complications and provide effective rehabilitation to the survivors. Another objective of the programme will be to establish a central burn registry. The programme will be launched in the current Five Year Plan in Medical colleges and their adjoining district hospitals in few states. Subsequently, in the next five year plan it will be rolled out in all the medical colleges and districts hospitals of the country so that burn care is provided as close to the site of accident as possible and patients need not to travel to big cities for burn care. The programme would essentially have three components i.e. Preventive programme, Burn injury management programme and Burn injury rehabilitation programme.

Gas fireplace contact burns in young children.

Science.gov (United States)

Zettel, Julie C; Khambalia, Amina; Barden, Wendy; Murthy, Trisha; Macarthur, Colin

2004-01-01

Contact burns from domestic appliances are common in young children. Recently, gas fireplaces have been recognized as a potential cause of contact burns in young children. We sought to quantify the frequency of gas fireplace contact burns in young children, to identify the etiology of contact, to describe the clinical presentation, and to describe clinical outcomes. Children with gas fireplace contact burn injuries presenting to The Hospital for Sick Children in Toronto (1999-2002) were identified using three data sources: the Canadian Hospitals Injury Reporting and Prevention Program Database, the Burn Unit Registry, and the Rehabilitation Services Database. Demographic, clinical, and outcomes data were collected on all children. During the 4-year study period, 27 children presented to the hospital because of a gas fireplace contact burn (approximately 9% of all contact burns). The median age of the children was 14 months (range, 8-36 months), with 16 boys (59%). Most children were burned in their own home. With regard to etiology, 10 children (37%) lost their balance near the fireplace, 2 (7%) walked too close to the glass front, and 8 (30%) touched the glass front out of curiosity. Almost half (44%) of the children burned the palms and digits of both hands. The median total burn surface area was 1% (range, 0.2-2.5%). In total, 30% of children were admitted to hospital, and 11% required skin grafts. All children had full wound closure after 4 to 43 days. Given the etiology of these burns (loss of balance or curiosity), passive prevention, such as barriers or changes in the composition of glass panels, may be the most effective approach to combat them.

Modulation of inflammatory and catabolic responses in severely burned children by early burn wound excision in the first 24 hours

NARCIS (Netherlands)

Barret, JP; Herndon, DN

Hypothesis: Early burn wound excision modulates the hypermetabolic response in severe pediatric burn injuries. Design: Before-after trial. Setting: A 30-bed burn referral center in a private, university-affiliated hospital. Methods: We studied 35 severely burned children who were divided into 2

Infections in critically ill burn patients.

Science.gov (United States)