Waste vitrification: prediction of acceptable compositions in a lime-soda-silica glass-forming system

International Nuclear Information System (INIS)

Gilliam, T.M.; Jantzen, C.M.

1996-10-01

A model is presented based upon calculated bridging oxygens which allows the prediction of the region of acceptable glass compositions for a lime-soda-silica glass-forming system containing mixed waste. The model can be used to guide glass formulation studies (e.g., treatability studies) or assess the applicability of vitrification to candidate waste streams

Performance Characteristics of Waste Glass Powder Substituting Portland Cement in Mortar Mixtures

Science.gov (United States)

Kara, P.; Csetényi, L. J.; Borosnyói, A.

2016-04-01

In the present work, soda-lime glass cullet (flint, amber, green) and special glass cullet (soda-alkaline earth-silicate glass coming from low pressure mercury-discharge lamp cullet and incandescent light bulb borosilicate glass waste cullet) were ground into fine powders in a laboratory planetary ball mill for 30 minutes. CEM I 42.5N Portland cement was applied in mortar mixtures, substituted with waste glass powder at levels of 20% and 30%. Characterisation and testing of waste glass powders included fineness by laser diffraction particle size analysis, specific surface area by nitrogen adsorption technique, particle density by pycnometry and chemical analysis by X-ray fluorescence spectrophotometry. Compressive strength, early age shrinkage cracking and drying shrinkage tests, heat of hydration of mortars, temperature of hydration, X-ray diffraction analysis and volume stability tests were performed to observe the influence of waste glass powder substitution for Portland cement on physical and engineering properties of mortar mixtures.

Effect of embedded silver nanoparticles on refractive index of soda lime glass

Science.gov (United States)

Sonal, Sharma, Annu; Aggarwal, Sanjeev

2018-05-01

Silver glass nanocomposites were prepared by exposing silver doped soda lime glass slides obtained via ion-exchange reaction to a beam of 200 keV Argon ions (Ar+) at an off normal angle of 400 with doses of 5x1015 ions cm-2 and 1x1016 ions cm-2. These nanocomposites were further characterized using UV-visible spectrophotometer so as to study their transmission and reflection behavior and compute their refractive index and real and imaginary parts of dielectric function.

Microbial communities associated with the anthropogenic, highly alkaline environment of a saline soda lime, Poland.

Science.gov (United States)

Kalwasińska, Agnieszka; Felföldi, Tamás; Szabó, Attila; Deja-Sikora, Edyta; Kosobucki, Przemysław; Walczak, Maciej

2017-07-01

Soda lime is a by-product of the Solvay soda process for the production of sodium carbonate from limestone and sodium chloride. Due to a high salt concentration and alkaline pH, the lime is considered as a potential habitat of haloalkaliphilic and haloalkalitolerant microbial communities. This artificial and unique environment is nutrient-poor and devoid of vegetation, due in part to semi-arid, saline and alkaline conditions. Samples taken from the surface layer of the lime and from the depth of 2 m (both having pH ~11 and EC e up to 423 dS m -1 ) were investigated using culture-based (culturing on alkaline medium) and culture-independent microbiological approaches (microscopic analyses and pyrosequencing). A surprisingly diverse bacterial community was discovered in this highly saline, alkaline and nutrient-poor environment, with the bacterial phyla Proteobacteria (representing 52.8% of the total bacterial community) and Firmicutes (16.6%) showing dominance. Compared to the surface layer, higher bacterial abundance and diversity values were detected in the deep zone, where more stable environmental conditions may occur. The surface layer was dominated by members of the genera Phenylobacterium, Chelativorans and Skermanella, while in the interior layer the genus Fictibacillus was dominant. The culturable aerobic, haloalkaliphilic bacteria strains isolated in this study belonged mostly to the genus Bacillus and were closely related to the species Bacillus pseudofirmus, B. cereus, B. plakortidis, B. thuringensis and B. pumilus.

Formation of silver colloids on ion exchanged soda lime silicate glasses by irradiation

International Nuclear Information System (INIS)

Yoshimura, E.M.; Okuno, E.

1998-01-01

The effect of ionizing radiation (gamma rays, X-rays and electrons) on soda lime silicate glasses, in which part of the Na + was substituted by Ag + by means of an ionic exchange process, was studied. The techniques of thermally stimulated depolarization current (TSDC) and transmission electron microscopy (TEM) were employed to follow the formation of silver colloids by irradiation. Also the thermoluminescence (TL) of the samples was measured and three peaks between room temperature and 450 C were observed. The TEM and TSDC results agree that, as expected, ionizing radiation promotes the formation of silver colloids on the ion exchanged surface of soda lime glasses. Soft X-rays are much more efficient in the process than gamma rays and electrons. The correlation with thermoluminescence glow curves indicates that the intensity of a TL peak at 230 C can provide a rapid means of evaluating the presence of silver colloids. TL sensitivities, measured as area under the glow curve per unit mass and unit dose, are very similar for ion exchanged and not exchanged samples submitted to X-ray irradiation, although the peak temperatures differ in about 40 C in the two cases. For both electron and gamma irradiated samples, the TL sensitivity drops about an order of magnitude when compared to the X-ray irradiated ones. (orig.)

Development of dense glass-ceramic from recycled soda-lime-silicate glass and fly ash for tiling

Science.gov (United States)

Mustaffar, Mohd Idham; Mahmud, Mohamad Haniza; Hassan, Mahadi Abu

2017-12-01

Dense glass-ceramics were prepared by sinter-crystallization process from a combination of soda-lime-silicate glass waste and fly ash. Bentonite clay that acted as a binder was also added in a prepared formulation. The powder mixture of soda-lime glass, fly ash and bentonite clay were compacted by using uniaxial hydraulic press machine and sintered at six (6) various temperatures namely 750, 800, 850, 900, 950 and 1000 °C. The heating rate and sintering time were set at 5 °C/min and 30 minutes respectively. The results revealed that modulus of rupture (MOR), density and linear shrinkage increase first from 750 to 800 °C but decrease later after 800 to 1000 °C. In the meantime, water absorption was showing completely an opposite trend. The glass-ceramic sintered at 800 °C was found to have the best combination of physical-mechanical properties and has the potential to be applied in the construction industry particularly as floor and wall tiles because of the simple manufacturing process at low temperature.

Cullet Manufacture Using the Cylindrical Induction Melter

International Nuclear Information System (INIS)

Miller, D. H.

2000-01-01

The base process for vitrification of the Am/Cm solution stored in F-canyon uses 25SrABS cullet as the glass former. A small portion of the cullet used in the SRTC development work was purchased from Corning while the majority was made in the 5 inch Cylindrical Induction Melter (CIM5). Task 1.01 of TTR-NMSS/SE-006, Additional Am-Cm Process Development Studies, requested that a process for the glass former (cullet) fabrication be specified. This report provides the process details for 25SrAB cullet production thereby satisfying Task 1.01

Value Recovery from Waste Liquid Crystal Display Glass Cullet through Leaching: Understanding the Correlation between Indium Leaching Behavior and Cullet Piece Size

OpenAIRE

Basudev Swain; Chan Gi Lee; Hyun Seon Hong

2018-01-01

For hydrometallurgical recovery of indium from glass cullet after dismantling a waste liquid crystal display (LCD), leaching is the rudimentary stage. Though size reduction of the cullet pieces adds convenience for recycling, from an efficiency and cost-effectiveness perspective regarding leaching process development, determining the proper cullet piece size is essential. Hence, in this study, leaching efficiency of indium as a function of cullet piece size was investigated, wherein the prope...

Effects of Aqueous Solutions on the Slow Crack Growth of Soda-Lime-Silicate Glass

Science.gov (United States)

Hausmann, Bronson D.; Salem, Jonathan A.

2016-01-01

The slow crack growth (SCG) parameters of soda-lime-silicate were measured in distilled and saltwater of various concentrations in order to determine if the presence of salt and the contaminate formation of a weak sodium film affects stress corrosion susceptibility. Past research indicates that solvents affect the rate of crack growth; however, the effects of salt have not been studied. The results indicate a small but statistically significant effect on the SCG parameters A and n at high concentrations; however, for typical engineering purposes, the effect can be ignored.

Use of rice rusk ash and spent catalyst as a source of raw material for the production and characterization of soda-lime silicate glasses destined for packaging

International Nuclear Information System (INIS)

Araujo, M.S.; Martinelli, J.R.; Genova, L.A.; Prado, U.S. do

2016-01-01

Study on the use of rice husk ash (RHA) and waste catalyst (ECAT), two industrial solid waste generated in large quantities in Brazil, getting soda-lime glass for the production of packaging. Both the waste may be classified as class II waste according to NBR 10,004. Samples were produced adding Na_2CO_3 and CaO to obtain a composition within the range of commercial soda-lime glasses. The results showed that both can be used as received (without any previous treatment) replacing important raw materials, source of Al_2O_3 and SiO2, necessary for glass formation. The produced samples were amber due to the presence of nickel (Ni2+ ions) from the ECAT and optical transmittance of 18%. These also showed good homogeneity, i.e., absence of bubbles and striae and dissolution rate higher than a commercial soda-lime glass. In general, the samples are presented suitable for applications that require low transmittance such as colored glass containers, which does not require perfect visibility and transparency. Finally, the waste level of incorporation was approximately 78 mass%. (author)

Can a soda-lime glass be used to demonstrate how patterns of strength dependence are influenced by pre-cementation and resin-cementation variables?

LENUS (Irish Health Repository)

Hooi, Paul

2013-01-01

To determine how the variability in biaxial flexure strength of a soda-lime glass analogue for a PLV and DBC material was influenced by precementation operative variables and following resin-cement coating.

The Effects of Salt Water on the Slow Crack Growth of Soda Lime Silicate Glass

Science.gov (United States)

Hausmann, Bronson D.; Salem, Jonathan A.

2016-01-01

The slow crack growth parameters of soda-lime silicate were measured in distilled and salt water of various concentrations in order to determine if stress corrosion susceptibility is affected by the presence of salt and the contaminate formation of a weak sodium film. Past research indicates that solvents effect the rate of crack growth, however, the effects of salt have not been studied. The results indicate a small but statistically significant effect on the slow crack growth parameters A and n. However, for typical engineering purposes, the effect can be ignored.

Fabrication and characterization of bioactive glass-ceramic using soda-lime-silica waste glass.

Science.gov (United States)

Abbasi, Mojtaba; Hashemi, Babak

2014-04-01

Soda-lime-silica waste glass was used to synthesize a bioactive glass-ceramic through solid-state reactions. In comparison with the conventional route, that is, the melt-quenching and subsequent heat treatment, the present work is an economical technique. Structural and thermal properties of the samples were examined by X-ray diffraction (XRD) and differential thermal analysis (DTA). The in vitro test was utilized to assess the bioactivity level of the samples by Hanks' solution as simulated body fluid (SBF). Bioactivity assessment by atomic absorption spectroscopy (AAS) and scanning electron microscopy (SEM) was revealed that the samples with smaller amount of crystalline phase had a higher level of bioactivity. Copyright © 2014 Elsevier B.V. All rights reserved.

Integrated treatment of acid mine drainage using BOF slag, lime/soda ash and reverse osmosis (RO): Implication for the production of drinking water

CSIR Research Space (South Africa)

Masindi, Vhahangwele

2017-12-01

Full Text Available -up with environmental friendly and zeroliquid-discharge technologies. The purpose of this novel study was to produce drinking water and recover valuable minerals from acid mine drainage using an integration of Basic Oxygen Furnace (BOF) slag, lime, soda ash and Reverse...

PREPARATION OF ZEOLITE X COATINGS ON SODA-LIME TYPE GLASS PLATES

Directory of Open Access Journals (Sweden)

M. Tatlier

Full Text Available Abstract The dissolution of glass in highly alkaline reaction mixtures and the impact of this phenomenon on zeolite coating formation were investigated. Coating samples were prepared and characterized by X-ray diffraction (XRD, field emission gun scanning electron microscopy (FEGSEM and thermogravimetry (TG. It was demonstrated that zeolite X coatings might be prepared on soda-lime glass. Glass dissolved to some degree, up to 2% of its original mass, in the reaction mixtures for the conditions investigated. This dissolution affected the zeolite synthesis taking place on the glass surface, resulting in phases different from those obtained on inert metal surfaces in some cases, especially for the use of reaction mixtures with relatively high Si/Al ratios. The percentage of dissolution of glass plates increased with their decreasing thickness, indicating a surface phenomenon for the dissolution. The stabilities of the coatings, which varied with the synthesis conditions, benefited from the addition of extra thin layers of polyacrylic acid.

Internal friction of hydrated soda-lime-silicate glasses.

Science.gov (United States)

Reinsch, S; Müller, R; Deubener, J; Behrens, H

2013-11-07

The internal friction of hydrated soda-lime-silica glasses with total water content (C(W)) up to 1.9 wt. % was studied by dynamic mechanical analysis (DMA) using temperature-frequency sweeps from 723 K to 273 K and from 1 s(-1) to 50 s(-1). Total water content and concentrations of H2O molecules (C(H2O)) and OH groups (C(OH)) in the DMA specimens were determined by infrared spectroscopy. For low water contents (C(W) ≈ C(OH) friction peaks below the glass transition (α relaxation) were assigned to the low-temperature motion of alkali ions (γ relaxation) and cooperative movements of dissimilar mobile species under participation of OH at higher temperature (β(OH) relaxation). For large water contents (C(W) > 1 wt. %), where significant amounts of molecular water are evident (C(H2O) > 0.15 wt. %), however, internal friction spectra change unexpectedly: the β(OH) peak heights saturate and a low temperature shoulder appears on the β-relaxation peak. This emerging relaxation mode (β(H2O) relaxation) was assigned to the motions of H2O molecules. β(H2O) relaxation was found to be faster than β(OH) but slower than γ relaxation. Activation energy of the different relaxation modes increased in the order γ < β(H2O) < β(OH) < α.

Alkali passivation mechanism of sol-gel derived TiO2-SiO2 films coated on soda-lime-silica glass substrates

Energy Technology Data Exchange (ETDEWEB)

Matsuda, A; Matsuno, Y; Katayama, S; Tsuno, T [Nippon Steel Glass Co. Ltd., Tokyo (Japan); Toge, N; Minami, T [University of Osaka Prefecture, Osaka (Japan). College of Engineering

1992-09-01

TiO2-SiO2 films prepared by the sol-gel method serves as an effective alkali passivation layer on a soda-lime-silica glass substrate and the film is superior to a sol-gel derived pure SiO2 film from the view point of weathering resistance improvement. To clarify the reason, alkali passivation mechanism of sol-gel derived TiO2-SiO2 glass films with different TiO2 contents coated on a soda-lime-silica glass substrate was studied by SIMS (secondary ion mass spectroscopy) and XPS (X-ray photoelectron spectroscopy) analyses, and compared with the results of a sol-gel derived pure SiO2 film. As a result, the following conclusions were obtained: An increase in TiO2 content in the TiO2 SiO2 film increases the sodium concentration in the film, which was induced by sodium migration from the glass substrate during the heat-treatment. Because of the presence of sodium the TiO2 -SiO2 films serve not as a barrier but as an effective getter of alkali ions and thereby effectively improve the weathering resistance Of the glass substrate. 10 refs., 6 figs.

OD bands in the IR spectra of a deuterated soda-lime-silica glass

Energy Technology Data Exchange (ETDEWEB)

Peuker, C.; Brzezinka, K.W.; Gaber, M.; Kohl, A.; Geissler, H. [Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin (Germany)

2001-07-01

IR spectra of a deuterated glass of the composition (in mol%) 16 Na{sub 2}O . 10 CaO . 74 SiO{sub 2} complete earlier spectroscopic studies on water-poor soda-lime-silica glasses. The approved IR spectroscopic method of the deuterium exchange allows a reliable assignment of the hydroxyl bands also in the case of glasses. By spectra comparison the assignment of the IR bands at 3500 and 2800 cm{sup -1} to hydroxyl groups with different hydrogen bonding is verified. The IR band at about 4500 cm{sup -1} is interpreted as both a combination of the stretching vibrations {nu}O-H and {nu}Si-OH and a combination of the stretching vibration {nu}O-H and the deformation vibration {delta}SiOH. The bands at 1763 and 1602 cm{sup -1} are attributed to combination vibrations of the glass network. (orig.)

Use of rice rusk ash and spent catalyst as a source of raw material for the production and characterization of soda-lime silicate glasses destined for packaging; Utilizacao de residuos de catalisador (ECAT) e cinzas da casca de arroz (CCA) na elaboracao de vidros silicatos soda-cal destinados ao setor de embalagem

Energy Technology Data Exchange (ETDEWEB)

Araujo, M.S.; Martinelli, J.R.; Genova, L.A.; Prado, U.S. do, E-mail: araujo.mariaana@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Ciencia e Tecnologia de Materiais

2016-07-01

Study on the use of rice husk ash (RHA) and waste catalyst (ECAT), two industrial solid waste generated in large quantities in Brazil, getting soda-lime glass for the production of packaging. Both the waste may be classified as class II waste according to NBR 10,004. Samples were produced adding Na{sub 2}CO{sub 3} and CaO to obtain a composition within the range of commercial soda-lime glasses. The results showed that both can be used as received (without any previous treatment) replacing important raw materials, source of Al{sub 2}O{sub 3} and SiO2, necessary for glass formation. The produced samples were amber due to the presence of nickel (Ni2+ ions) from the ECAT and optical transmittance of 18%. These also showed good homogeneity, i.e., absence of bubbles and striae and dissolution rate higher than a commercial soda-lime glass. In general, the samples are presented suitable for applications that require low transmittance such as colored glass containers, which does not require perfect visibility and transparency. Finally, the waste level of incorporation was approximately 78 mass%. (author)

A completely transparent, adhesively bonded soda-lime glass block masonry system

Directory of Open Access Journals (Sweden)

F. Oikonomopoulou

2015-01-01

Full Text Available A pioneering, all transparent, self-supporting glass block facade is presented in this paper. Previously realized examples utilize embedded metal components in order to obtain the desired structural performance despite the fact that these elements greatly affect the facade’s overall transparency level. Undeniably, the oxymoron ‘transparency and strength’ remains the prime concern in such applications. In this paper, a new, innovative structural system for glass block facades is described, which demonstrably meets both criteria. The structure is exclusively constructed by monolithic glass blocks, bonded with a colourless, UV-curing adhesive, obtaining thus a maximum transparency. In addition, the desired structural performance is achieved solely through the masonry system, without any opaque substructure. Differing from previous realized projects, solid soda-lime glass blocks are used rather than borosilicate ones. This article provides an overview of the integrated architectural and structural design and discusses the choice of materials. The structural verification of the system is demonstrated. The results show that the adhesively bonded glass block structure has the required self-structural behaviour, but only if strict tolerances are met in the geometry of the glass blocks.

A study on the plasticity of soda-lime silica glass via molecular dynamics simulations

Science.gov (United States)

Urata, Shingo; Sato, Yosuke

2017-11-01

Molecular dynamics (MD) simulations were applied to construct a plasticity model, which enables one to simulate deformations of soda-lime silica glass (SLSG) by using continuum methods. To model the plasticity, stress induced by uniaxial and a variety of biaxial deformations was measured by MD simulations. We found that the surfaces of yield and maximum stresses, which are evaluated from the equivalent stress-strain curves, are reasonably represented by the Mohr-Coulomb ellipsoid. Comparing a finite element model using the constructed plasticity model to a large scale atomistic model on a nanoindentation simulation of SLSG reveals that the empirical method is accurate enough to evaluate the SLSG mechanical responses. Furthermore, the effect of ion-exchange on the SLSG plasticity was examined by using MD simulations. As a result, it was demonstrated that the effects of the initial compressive stress on the yield and maximum stresses are anisotropic contrary to our expectations.

Iron oxide coating films in soda-lime glass by triboadhesion

Energy Technology Data Exchange (ETDEWEB)

Aguilar, J. O.; Arjona, M. J. [Boulevard Bahia s/n esq. Ignacio Comonfort, Chetumal (Mexico); Rodriguez-Lelis, J. M. [Interior Internado Palmira s/n, Cuernavaca, Morelos (Mexico)

2009-04-15

In the triboadhesion process the coating material is passed through a rotating cotton mop and the substrate to be coated. The cotton mop rotates at high velocity and exerts pressure on the surface of the substrate. The combined effect of pressure and velocity of the coating mop on the substrate increases its temperature close to the melting point, allowing deposition and diffusion of the coating material within the substrate. After it is deposited, its particles are embedded within the base material forming a thin film composite. The amount of the coating material deposited on the substrate has its maximum at the surface and then decreases as a function of the local temperature within the base material. Bearing this in mind, in the present work, triboadhesion is employed to deposit iron oxide in a substrate of soda-lime glass, with the purpose of determining the feasibility of using this technique for solar control coatings. It was found, through electronic scan microscopy, that a composite material film is formed following the coating direction. Reflectance and transmittance tests were carried out on the glass samples. A 20% difference was found in the visible spectral region (VIS), and a reduction between 10 and 20% in the Near Infrared Region (NIR). These results showed that the triboadhesion is a promising technique for the application of thin films for solar control or solar cells

Iron oxide coating films in soda-lime glass by triboadhesion

International Nuclear Information System (INIS)

Aguilar, J. O.; Arjona, M. J.; Rodriguez-Lelis, J. M.

2009-01-01

In the triboadhesion process the coating material is passed through a rotating cotton mop and the substrate to be coated. The cotton mop rotates at high velocity and exerts pressure on the surface of the substrate. The combined effect of pressure and velocity of the coating mop on the substrate increases its temperature close to the melting point, allowing deposition and diffusion of the coating material within the substrate. After it is deposited, its particles are embedded within the base material forming a thin film composite. The amount of the coating material deposited on the substrate has its maximum at the surface and then decreases as a function of the local temperature within the base material. Bearing this in mind, in the present work, triboadhesion is employed to deposit iron oxide in a substrate of soda-lime glass, with the purpose of determining the feasibility of using this technique for solar control coatings. It was found, through electronic scan microscopy, that a composite material film is formed following the coating direction. Reflectance and transmittance tests were carried out on the glass samples. A 20% difference was found in the visible spectral region (VIS), and a reduction between 10 and 20% in the Near Infrared Region (NIR). These results showed that the triboadhesion is a promising technique for the application of thin films for solar control or solar cells

Encapsulation of TRISO particle fuel in durable soda-lime-silicate glasses

International Nuclear Information System (INIS)

Heath, Paul G.; Corkhill, Claire L.; Stennett, Martin C.; Hand, Russell J.; Meyer, Willem C.H.M.; Hyatt, Neil C.

2013-01-01

Tri-Structural Isotropic (TRISO) coated particle-fuel is a key component in designs for future high temperature nuclear reactors. This study investigated the suitability of three soda lime silicate glass compositions, for the encapsulation of simulant TRISO particle fuel. A cold press and sinter (CPS) methodology was employed to produce TRISO particle–glass composites. Composites produced were determined to have an aqueous durability, fracture toughness and Vickers’ hardness comparable to glasses currently employed for the disposal of high level nuclear wastes. Sintering at 700 °C for 30 min was found to remove all interconnected porosity from the composite bodies and oxidation of the outer pyrolytic carbon layer during sintering was prevented by processing under a 5% H 2 /N 2 atmosphere. However, the outer pyrolytic carbon layer was not effectively wetted by the encapsulating glass matrix. The aqueous durability of the TRISO particle–glass composites was investigated using PCT and MCC-1 tests combined with geochemical modelling. It was found that durability was dependent on silicate and calcium solution saturation. This study provides significant advancements in the preparation of TRISO particle encapsulant waste forms. The potential for the use of non-borosilicate sintered glass composites for TRISO particle encapsulation has been confirmed, although further refinements are required

Encapsulation of TRISO particle fuel in durable soda-lime-silicate glasses

Energy Technology Data Exchange (ETDEWEB)

Heath, Paul G.; Corkhill, Claire L.; Stennett, Martin C.; Hand, Russell J. [Immobilisation Science Laboratory, Department of Materials Science and Engineering, Robert Hadfield Building, University of Sheffield, Sheffield S1 3JD (United Kingdom); Meyer, Willem C.H.M. [Necsa, South African Nuclear Energy Corporation, PO Box 582, Pretoria, Gauteng (South Africa); Hyatt, Neil C., E-mail: n.c.hyatt@sheffield.ac.uk [Immobilisation Science Laboratory, Department of Materials Science and Engineering, Robert Hadfield Building, University of Sheffield, Sheffield S1 3JD (United Kingdom)

2013-05-15

Tri-Structural Isotropic (TRISO) coated particle-fuel is a key component in designs for future high temperature nuclear reactors. This study investigated the suitability of three soda lime silicate glass compositions, for the encapsulation of simulant TRISO particle fuel. A cold press and sinter (CPS) methodology was employed to produce TRISO particle–glass composites. Composites produced were determined to have an aqueous durability, fracture toughness and Vickers’ hardness comparable to glasses currently employed for the disposal of high level nuclear wastes. Sintering at 700 °C for 30 min was found to remove all interconnected porosity from the composite bodies and oxidation of the outer pyrolytic carbon layer during sintering was prevented by processing under a 5% H{sub 2}/N{sub 2} atmosphere. However, the outer pyrolytic carbon layer was not effectively wetted by the encapsulating glass matrix. The aqueous durability of the TRISO particle–glass composites was investigated using PCT and MCC-1 tests combined with geochemical modelling. It was found that durability was dependent on silicate and calcium solution saturation. This study provides significant advancements in the preparation of TRISO particle encapsulant waste forms. The potential for the use of non-borosilicate sintered glass composites for TRISO particle encapsulation has been confirmed, although further refinements are required.

Bone Loss at Implant with Titanium Abutments Coated by Soda Lime Glass Containing Silver Nanoparticles: A Histological Study in the Dog

Science.gov (United States)

Martinez, Arturo; Guitián, Francisco; López-Píriz, Roberto; Bartolomé, José F.; Cabal, Belén; Esteban-Tejeda, Leticia; Torrecillas, Ramón; Moya, José S.

2014-01-01

The aim of the present study was to evaluate bone loss at implants connected to abutments coated with a soda-lime glass containing silver nanoparticles, subjected to experimental peri-implantitis. Also the aging and erosion of the coating in mouth was studied. Five beagle dogs were used in the experiments. Three implants were placed in each mandible quadrant: in 2 of them, Glass/n-Ag coated abutments were connected to implant platform, 1 was covered with a Ti-mechanized abutment. Experimental peri-implantitis was induced in all implants after the submarginal placement of cotton ligatures, and three months after animals were euthanatized. Thickness and morphology of coating was studied in abutment cross-sections by SEM. Histology and histo-morphometric studies were carried on in undecalfied ground slides. After the induced peri-implantitis: 1.The abutment coating shown losing of thickness and cracking. 2. The histometry showed a significant less bone loss in the implants with glass/n-Ag coated abutments. A more symmetric cone of bone resorption was observed in the coated group. There were no significant differences in the peri-implantitis histological characteristics between both groups of implants. Within the limits of this in-vivo study, it could be affirmed that abutments coated with biocide soda-lime-glass-silver nanoparticles can reduce bone loss in experimental peri-implantitis. This achievement makes this coating a suggestive material to control peri-implantitis development and progression. PMID:24466292

Bone loss at implant with titanium abutments coated by soda lime glass containing silver nanoparticles: a histological study in the dog.

Directory of Open Access Journals (Sweden)

Arturo Martinez

Full Text Available The aim of the present study was to evaluate bone loss at implants connected to abutments coated with a soda-lime glass containing silver nanoparticles, subjected to experimental peri-implantitis. Also the aging and erosion of the coating in mouth was studied. Five beagle dogs were used in the experiments. Three implants were placed in each mandible quadrant: in 2 of them, Glass/n-Ag coated abutments were connected to implant platform, 1 was covered with a Ti-mechanized abutment. Experimental peri-implantitis was induced in all implants after the submarginal placement of cotton ligatures, and three months after animals were euthanatized. Thickness and morphology of coating was studied in abutment cross-sections by SEM. Histology and histo-morphometric studies were carried on in undecalfied ground slides. After the induced peri-implantitis: 1.The abutment coating shown losing of thickness and cracking. 2. The histometry showed a significant less bone loss in the implants with glass/n-Ag coated abutments. A more symmetric cone of bone resorption was observed in the coated group. There were no significant differences in the peri-implantitis histological characteristics between both groups of implants. Within the limits of this in-vivo study, it could be affirmed that abutments coated with biocide soda-lime-glass-silver nanoparticles can reduce bone loss in experimental peri-implantitis. This achievement makes this coating a suggestive material to control peri-implantitis development and progression.

Wiping frictional properties of electrospun hydrophobic/hydrophilic polyurethane nanofiber-webs on soda-lime glass and silicon-wafer.

Science.gov (United States)

Watanabe, Kei; Wei, Kai; Nakashima, Ryu; Kim, Ick Soo; Enomoto, Yuji

2013-04-01

In the present work, we conducted the frictional tests of hydrophobic and hydrophilic polyurethane (PUo and PUi) nanofiber webs against engineering materials; soda-lime glass and silicon wafer. PUi/glass combination, with highest hydrophilicity, showed the highest friction coefficient which decrease with the increase of the applied load. Furthermore, the effects of fluorine coating are also investigated. The friction coefficient of fluorine coated hydrophobic PU nanofiber (PUof) shows great decrease against the silicon wafer. Finally, wiping ability and friction property are investigated when the substrate surface is contaminated. Nano-particle dusts are effectively collected into the pores by wiping with PUo and PUi nanofiber webs both on glass and silicon wafer. The friction coefficient gradually increased with the increase of the applied load.

Structural analysis and visible light-activated photocatalytic activity of iron-containing soda lime aluminosilicate glass

Energy Technology Data Exchange (ETDEWEB)

Iida, Yusuke; Akiyama, Kazuhiko [Department of Chemistry, Graduate School of Science and Engineering, Tokyo Metropolitan University, 1-1 Minami-Osawa, Hachi-Oji, Tokyo 192-0397 (Japan); Kobzi, Balázs; Sinkó, Katalin; Homonnay, Zoltán [Institute of Chemistry, Eötvös Loránd University, Pázmany P. s., 1/A, Budapest 1117 (Hungary); Kuzmann, Ernő [Institute of Chemistry, Eötvös Loránd University, Pázmany P. s., 1/A, Budapest 1117 (Hungary); Laboratory of Nuclear Chemistry, Chemical Research Center, Hungarian Academy of Sciences, Budapest 1512 (Hungary); Ristić, Mira; Krehula, Stjepko [Division of Materials Chemistry, RuđerBošković Institute, Bijenička cesta 54, Zagreb 10000 (Croatia); Nishida, Tetsuaki [Department of Biological and Environmental Chemistry, Faculty of Humanity-Oriented Science and Engineering, Kinki University, 11-6 Kayanomori, Iizuka, Fukuoka 820-8555 (Japan); Kubuki, Shiro, E-mail: kubuki@tmu.ac.jp [Department of Chemistry, Graduate School of Science and Engineering, Tokyo Metropolitan University, 1-1 Minami-Osawa, Hachi-Oji, Tokyo 192-0397 (Japan)

2015-10-05

Highlights: • Hematite was precipitated by heat treatment of iron aluminosilicate glass. • The hematite phase shows visible light photocatalytic activity. • We could prepare an effective photocatalyst from ‘ubiquitous elements’. - Abstract: A relationship between structure and visible light-activated photocatalytic activity of iron-containing soda lime aluminosilicate (15Na{sub 2}O⋅15CaO⋅40Fe{sub 2}O{sub 3}⋅xAl{sub 2}O{sub 3}⋅(30−x)SiO{sub 2}) glass (xNCFAS) was investigated by means of {sup 57}Fe-Mössbauer spectroscopy, X-ray diffractometry (XRD) and UV–visible light absorption spectroscopy (UV–VIS). The {sup 57}Fe-Mössbauer spectrum of 11NCFAS glass measured after heat-treatment at 1000 °C for 100 min was composed of a paramagnetic doublet due to Fe{sup III}(T{sub d}) and two magnetic sextets due to regular hematite (α-Fe{sub 2}O{sub 3}) and hematite with larger internal magnetic field. X-ray diffraction patterns of heat-treated xNCFAS samples resulted in decrease of α-Fe{sub 2}O{sub 3} and increase of Ca{sub 2}Fe{sub 22}O{sub 33} or CaFe{sub 2}O{sub 4} with alumina content. A quick decrease in methylene blue (MB) concentration from 15.6 to 4.7 μmol L{sup −1} was observed in the photocatalytic reaction test with 40 mg of heat-treated 11NCFAS glass under visible light-exposure. The largest first-order rate constant of MB decomposition (k) was estimated to be 9.26 × 10{sup −3} min{sup −1}. Tauc’s plot yielded a band gap energy (E{sub g}) of 1.88 eV for heat-treated 11NCFAS glass, which is smaller than previously reported E{sub g} of 2.2 eV for α-Fe{sub 2}O{sub 3}. These results prove that addition of Al{sub 2}O{sub 3} into iron-containing soda lime silicate glass is favorable for the preparation of improved visible light-photocatalyst with ‘ubiquitous’ elements.

Microstructure characterization of the soda-lime-glass/copper-indium-gallium-selenium interface in Cu-poor Cu(In,Ga)Se{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Wang, Jian, E-mail: wangjustb@gmail.com; Qiao, Yi; Zhu, Jie, E-mail: jiezhu@ustb.edu.cn

2015-05-29

The microstructure characteristics of the soda-lime-glass/Cu(In,Ga)Se{sub 2} (SLG/CIGS) interface in Cu-poor CIGS films are investigated by transmission electron microscopy and selected area electronic diffraction (SAED). The SAED patterns show very sharp and strong spots, indicating the main structure of CIGS chalcopyrite. Small dispersed crystals with size distribution from 2 to 5 nm seem to be embedded in amorphous matrix, and additional spots indicate the presence of an ordered vacancy compound (OVC). This observation is consistent with the Raman results, and the OVC phase with the nanoclusters exists in the CIGS matrix, instead of layer structure. Lattice distortion results in local changes in contrast. Some pseudo-disordered structure is observed, however, the structure is actually the chalcopyrite CIGS structure. 180° rotation twins are also observed at the SLG/CIGS interface. Lattice distortion is widely observed at the interface of the Cu-poor CIGS films, and the extra spots could be caused by different lattice orientations. - Highlights: • Cu(In,Ga)Se{sub 2} (CIGS) were prepared on bare soda-lime-glass (SLG) substrates. • Microstructure of the SLG/CIGS interface was investigated. • An ordered vacancy compound (OVC) phase was observed. • The OVC phase with nanoclusters exists in the CIGS matrix, instead of layer structure. • 180° rotation twins were observed at the SLG/CIGS interface.

Effect of sintering temperature on physical, structural and optical properties of wollastonite based glass-ceramic derived from waste soda lime silica glasses

Directory of Open Access Journals (Sweden)

Karima Amer Almasri

Full Text Available The impact of different sintering temperatures on physical, optical and structural properties of wollastonite (CaSiO3 based glass-ceramics were investigated for its potential application as a building material. Wollastonite based glass-ceramics was provided by a conventional melt-quenching method and followed by a controlled sintering process. In this work, soda lime silica glass waste was utilized as a source of silicon. The chemical composition and physical properties of glass were characterized by using Energy Dispersive X-ray Fluorescence (EDXRF and Archimedes principle. The Archimedes measurement results show that the density increased with the increasing of sintering temperature. The generation of CaSiO3, morphology, size and crystal phase with increasing the heat-treatment temperature were examined by field emission scanning electron microscopy (FESEM, Fourier transforms infrared reflection spectroscopy (FTIR, and X-ray diffraction (XRD. The average calculated crystal size gained from XRD was found to be in the range 60 nm. The FESEM results show a uniform distribution of particles and the morphology of the wollastonite crystal is in relict shapes. The appearance of CaO, SiO2, and Ca-O-Si bands disclosed from FTIR which showed the formation of CaSiO3 crystal phase. In addition to the calculation of the energy band gap which found to be increased with increasing sintering temperature. Keywords: Soda lime silica glass, Wollastonite, Sintering, Structural properties, Optical properties

Modeling and evaluating of surface roughness prediction in micro-grinding on soda-lime glass considering tool characterization

Science.gov (United States)

Cheng, Jun; Gong, Yadong; Wang, Jinsheng

2013-11-01

The current research of micro-grinding mainly focuses on the optimal processing technology for different materials. However, the material removal mechanism in micro-grinding is the base of achieving high quality processing surface. Therefore, a novel method for predicting surface roughness in micro-grinding of hard brittle materials considering micro-grinding tool grains protrusion topography is proposed in this paper. The differences of material removal mechanism between convention grinding process and micro-grinding process are analyzed. Topography characterization has been done on micro-grinding tools which are fabricated by electroplating. Models of grain density generation and grain interval are built, and new predicting model of micro-grinding surface roughness is developed. In order to verify the precision and application effect of the surface roughness prediction model proposed, a micro-grinding orthogonally experiment on soda-lime glass is designed and conducted. A series of micro-machining surfaces which are 78 nm to 0.98 μm roughness of brittle material is achieved. It is found that experimental roughness results and the predicting roughness data have an evident coincidence, and the component variable of describing the size effects in predicting model is calculated to be 1.5×107 by reverse method based on the experimental results. The proposed model builds a set of distribution to consider grains distribution densities in different protrusion heights. Finally, the characterization of micro-grinding tools which are used in the experiment has been done based on the distribution set. It is concluded that there is a significant coincidence between surface prediction data from the proposed model and measurements from experiment results. Therefore, the effectiveness of the model is demonstrated. This paper proposes a novel method for predicting surface roughness in micro-grinding of hard brittle materials considering micro-grinding tool grains protrusion

Nonlinear relationship between the Product Consistency Test (PCT) response and the Al/B ratio in a soda-lime aluminoborosilicate glass

Energy Technology Data Exchange (ETDEWEB)

Farooqi, Rahmat Ullah, E-mail: rufarooqi@postech.ac.kr [Division of Advanced Nuclear Engineering, Pohang University of Science and Technology, 77 Cheongam-Ro, Nam-Gu, Pohang, Gyeongbuk 790-784 (Korea, Republic of); Hrma, Pavel [Division of Advanced Nuclear Engineering, Pohang University of Science and Technology, 77 Cheongam-Ro, Nam-Gu, Pohang, Gyeongbuk 790-784 (Korea, Republic of); Pacific Northwest National Laboratory, Richland, WA (United States)

2016-06-15

We have investigated the effect of Al/B ratio on the Product Consistency Test (PCT) response. In an aluminoborosilicate soda-lime glass based on a modified International Simple Glass, ISG-3, the Al/B ratio varied from 0 to 0.55 (in mole fractions). In agreement with various models of the PCT response as a function of glass composition, we observed a monotonic increase of B and Na releases with decreasing Al/B mole ratio, but only when the ratio was higher than 0.05. Below this value (Al/B < 0.05), we observed a sharp decrease that we attribute to B in tetrahedral coordination.

Effect of ZnO on the Physical Properties and Optical Band Gap of Soda Lime Silicate Glass

Science.gov (United States)

Zaid, Mohd Hafiz Mohd; Matori, Khamirul Amin; Aziz, Sidek Hj. Abdul; Zakaria, Azmi; Ghazali, Mohd Sabri Mohd

2012-01-01

This manuscript reports on the physical properties and optical band gap of five samples of soda lime silicate (SLS) glass combined with zinc oxide (ZnO) that were prepared by a melting and quenching process. To understand the role of ZnO in this glass structure, the density, molar volume and optical band gaps were investigated. The density and absorption spectra in the Ultra-Violet-Visible (UV-Visible) region were recorded at room temperature. The results show that the densities of the glass samples increased as the ZnO weight percentage increased. The molar volume of the glasses shows the same trend as the density: the molar volume increased as the ZnO content increased. The optical band gaps were calculated from the absorption edge, and it was found that the optical band gap decreased from 3.20 to 2.32 eV as the ZnO concentration increased. PMID:22837711

Use of wasted foundry sand (WFS) as a partial substitute for silica in a soda lime glass

International Nuclear Information System (INIS)

Martin, A.C.; Ueno, O.K.; Folgueras, M.V.

2016-01-01

The waste foundry sand (WFS) is the main waste generates in foundry industries. Studies in the literature suggest the use of WFS in different materials, such as concrete, brick or asphalt. This work aims to partially replace the silica of a soda-lime glass by the WFS. The waste foundry sand has in its composition elements such as iron and aluminum that can affect the glass quality, which justifies the residue processing to reduce the impurity content. The treatments, that included mechanical agitation and thermal treatment, resulted in a slight decrease in the percent of iron with consequent increase of the silica content. After treatment, some sands were incorporated into the glass, that showed green color but with lower absorption intensity for the sand with less iron content. It was observed that it's possible to obtain glasses using WFS, however, there is difficulty in color controlling. (author

Effect of sintering on crystallization and structural properties of soda lime silica glass

Directory of Open Access Journals (Sweden)

Zaid Mohd Hafiz Mohd

2017-01-01

Full Text Available The effect of sintering temperatures on crystallization and structural of the soda lime silica (SLS glass was reported. Elemental weight composition of the SLS glass powder was identified through Energy dispersive X-ray fluorescence (EDXRF analysis while the thermal behavior of the glass was determined using Differential thermal analysis (DTA technique. Archimedes’ method and direct geometric measurement were respectively used to determine bulk density and linear shrinkage of the glass samples. Crystallisation behavior of the samples was investigated by X-ray diffraction (XRD analysis and chemical bonds present in the samples were measured using Fourier Transform Infrared (FTIR spectroscopy. Results showed an increase in the density and linear shrinkage of the samples as a function of the sintering temperature. The XRD analysis revealed the formation of α-quartz (SiO2 and a minor amount of devitrite phases in the samples and these were further verified through the detection of chemical bonds by FTIR after sintering at 800ºC. The properties of the glass-ceramics can be explained on the basis of crystal chemistry which indicated that the alkali ions formed as carriers in the random network structure and can be recommended for the manufacture of glass fiber or toughened glass-ceramic insulators.

A laser-based technology for fabricating a soda-lime glass based microfluidic device for circulating tumour cell capture.

Science.gov (United States)

Nieto, Daniel; Couceiro, Ramiro; Aymerich, Maria; Lopez-Lopez, Rafael; Abal, Miguel; Flores-Arias, María Teresa

2015-10-01

We developed a laser-based technique for fabricating microfluidic microchips on soda-lime glass substrates. The proposed methodology combines a laser direct writing, as a manufacturing tool for the fabrication of the microfluidics structures, followed by a post-thermal treatment with a CO2 laser. This treatment will allow reshaping and improving the morphological (roughness) and optical qualities (transparency) of the generated microfluidics structures. The use of lasers commonly implemented for material processing makes this technique highly competitive when compared with other glass microstructuring approaches. The manufactured chips were tested with tumour cells (Hec 1A) after being functionalized with an epithelial cell adhesion molecule (EpCAM) antibody coating. Cells were successfully arrested on the pillars after being flown through the device giving our technology a translational application in the field of cancer research. Copyright © 2015 Elsevier B.V. All rights reserved.

Phase modification and dielectric properties of a cullet-paper ash-kaolin clay-based ceramic

Science.gov (United States)

Samah, K. A.; Sahar, M. R.; Yusop, M.; Omar, M. F.

2018-03-01

Novel ceramics from waste material made of ( x) paper ash-(80 - x) cullet-20 kaolin clay (10wt% ≤ x ≤ 30wt%) were successfully synthesized using a conventional solid-state reaction technique. Energy-dispersive X-ray analysis confirmed the presence of Si, Ca, Al, and Fe in the waste material for preparing these ceramics. The influence of the cullet content on the phase structures and the dielectric properties of these ceramics were systematically investigated. The impedance spectra were verified in the range from 1 Hz to 10 MHz at room temperature. The phase of the ceramics was found to primarily consist of wollastonite (CaSiO3), along with minor phases of γ-dicalcium silicate (Ca2SiO4) and quartz (SiO2). The sample with a cullet content of 55wt% possessed the optimum wollastonite structure and exhibited good dielectric properties. An increase of the cullet content beyond 55wt% resulted in a structural change from wollastonite to dicalcium silicate, a decrease in dielectric constant, and an increase in dielectric loss. All experimental results suggested that these novel ceramics from waste are applicable for electronic devices.

Effect of barrier layers on the properties of indium tin oxide thin films on soda lime glass substrates

International Nuclear Information System (INIS)

Lee, Jung-Min; Choi, Byung-Hyun; Ji, Mi-Jung; An, Yong-Tae; Park, Jung-Ho; Kwon, Jae-Hong; Ju, Byeong-Kwon

2009-01-01

In this paper, the electrical, structural and optical properties of indium tin oxide (ITO) films deposited on soda lime glass (SLG) haven been investigated, along with high strain point glass (HSPG) substrate, through radio frequency magnetron sputtering using a ceramic target (In 2 O 3 :SnO 2 , 90:10 wt.%). The ITO films deposited on the SLG show a high electrical resistivity and structural defects compared with those deposited on HSPG due to the Na ions from the SLG diffusing to the ITO film by annealing. However, these properties can be improved by intercalating a barrier layer of SiO 2 or Al 2 O 3 between the ITO film and the SLG substrate. SIMS analysis has confirmed that the barrier layer inhibits the Na ion's diffusion from the SLG. In particular, the ITO films deposited on the Al 2 O 3 barrier layer, show better properties than those deposited on the SiO 2 barrier layer.

Effects of ion implantation on the hardness and friction behaviour of soda-lime silica glass

International Nuclear Information System (INIS)

Bull, S.J.; Page, T.F.

1992-01-01

Ion implantation-induced changes in the near-surface mechanical properties of soda-lime silica glass have been investigated by indentation and scratch testing and have been found to be more complicated than changes in the corresponding properties of crystalline ceramic materials. Argon, nitrogen, carbon and potassium ions were used with energies in the range 45-300 keV. Hardness and scratch friction tests were performed under ambient laboratory conditions. At low doses, a decrease in hardness and an increase in both friction and surface stress are observed which are attributed to the electronic damage produced by ion implantation. At higher doses, the hardness increases again and a maximum is produced similar to the behaviour observed for crystalline materials. Similarly there is found to be a second stress and friction peak at this dose. This behaviour is shown to be due to the build-up of displacement damage produced by ion implantation and is thus very similar to the radiation hardening (and eventual amorphization) behaviour of ion-implanted crystalline ceramics. For glass, ''amorphization'' probably corresponds to some change in the existing amorphous state which, in turn, is responsible for the reduction in hardness, stress and friction at the highest doses. (author)

Studies on the Potential of Waste Soda Lime Silica Glass in Glass Ionomer Cement Production

Directory of Open Access Journals (Sweden)

V. W. Francis Thoo

2013-01-01

Full Text Available Glass ionomer cements (GIC are produced through acid base reaction between calcium-fluoroaluminosilicate glass powder and polyacrylic acid (PAA. Soda lime silica glasses (SLS, mainly composed of silica (SiO2, have been utilized in this study as the source of SiO2 for synthesis of Ca-fluoroaluminosilicate glass. Therefore, the main objective of this study was to investigate the potential of SLS waste glass in producing GIC. Two glasses, GWX 1 (analytical grade SiO2 and GWX 2 (replacing SiO2 with waste SLS, were synthesized and then characterized using X-ray diffraction (XRD and energy dispersive X-ray (EDX. Synthesized glasses were then used to produce GIC, in which the properties were characterized using Fourier transform infrared spectroscopy (FT-IR and compressive test (from 1 to 28 days. XRD results showed that amorphous glass was produced by using SLS waste glass (GWX 2, which is similar to glass produced using analytical grade SiO2 (GWX 1. Results from FT-IR showed that the setting reaction of GWX 2 cements is slower compared to cement GWX 1. Compressive strengths for GWX 1 cements reached up to 76 MPa at 28 days, whereas GWX 2 cements showed a slightly higher value, which is 80 MPa.

Formation of silver nanoparticles inside a soda-lime glass matrix in the presence of a high intensity Ar+ laser beam

International Nuclear Information System (INIS)

Niry, M. D.; Khalesifard, H. R.; Mostafavi-Amjad, J.; Ahangary, A.; Azizian-Kalandaragh, Y.

2012-01-01

Formation and motion of the silver nanoparticles inside an ion-exchanged soda-lime glass in the presence of a focused high intensity continuous wave Ar + laser beam (intensity: 9.2 x 10 4 W/cm 2 ) have been studied in here. One-dimensional diffusion equation has been used to model the diffusion of the silver ions into the glass matrix, and a two-dimensional reverse diffusion model has been introduced to explain the motion of the silver clusters and their migration toward the glass surface in the presence of the laser beam. The results of the mentioned models were in agreement with our measurements on thickness of the ion-exchange layer by means of optical microscopy and recorded morphology of the glass surface around the laser beam axis by using a Mirau interferometer. SEM micrographs were used to extract the size distribution of the migrated silver particles over the glass surface.

A dynamic fatigue study of soda-lime silicate and borosilicate glasses using small scale indentation flaws

International Nuclear Information System (INIS)

Dabbs, T.P.; Lawn, B.R.; Kelly, P.L.

1982-01-01

The dynamic fatigue characteristics of two glasses, soda-lime silicate and borosilicate, in water have been studied using a controlled indentation flaw technique. It is argued that the indentation approach offers several advantages over more conventional fatigue testing procedures: (i) the reproducibility of data is relatively high, eliminating statistics as a basis of analysis: (ii) the flaw ultimately responsible for failure is well defined and may be conveniently characterised before and after (and during, if necessary) the strength test; (iii) via adjustment of the indentation load, the size of the flaw can be suitably predetermined. Particular attention is devoted to the third point because of the facility it provides for systematic investigation of the range of flaw sizes over which macroscopic crack behaviour remains applicable. The first part of the paper summarises the essential fracture mechanics theory of the extension of an indentation flaw to failure. In the next part of the paper the results of dynamic fatigue tests on glass rods in distilled water are described. Data are obtained for Vickers indentation loads in the range 0.05 to 100 N, corresponding to contact dimensions of 2 to 100 μm. Finally, the implications of the results in relation to the response of 'natural' flaws are discussed. (author)

Characterization of residues of effluent treatment plant from lapping process of soda-lime glass and its application in the production of concrete

International Nuclear Information System (INIS)

Antonio, Aline Pignaton; Calmon, Joao Luiz; Tristao, Fernando Avancini

2012-01-01

This study enunciates the physical, chemical and mineralogical composition of the residue from the process of ETE cutting of soda-lime glasses and its application in concrete as a replacement to the weight of CPV ARI RS cement, at levels of 0, 5, 10, 15 and 20%. Tests were performed on fresh and hardened (ages 3, 7, 28 and 300 days). The results were compared and statistically analyzed. In the fresh state, reductions in the amount of exuding water and consistency were observed. The results of compressive strength were statistically different, while the results for the tensile strength by diametrical compression and modulus of elasticity results were belonging to homogeneous groups. Beneficial effects the levels of residue on the cementitious matrix and the transition zone of concrete were identified by SEM, particularly concrete in S15

Photocatalytic activity of titanium dioxide modified concrete materials - influence of utilizing recycled glass cullets as aggregates.

Science.gov (United States)

Chen, Jun; Poon, Chi-Sun

2009-08-01

Combining the use of photocatalysts with cementitious materials is an important development in the field of photocatalytic air pollution mitigation. This paper presents the results of a systematic study on assessing the effectiveness of pollutant degradation by concrete surface layers that incorporate a photocatalytic material - Titanium Dioxide. The photocatalytic activity of the concrete samples was determined by photocatalytic oxidation of nitric oxide (NO) in the laboratory. Recycled glass cullets, derived from crushed waste beverage bottles, were used to replace sand in preparing the concrete surface layers. Factors, which may affect the pollutant removal performance of the concrete layers including glass color, aggregate size and curing age, were investigated. The results show a significant enhancement of the photocatalytic activity due to the use of glass cullets as aggregates in the concrete layers. The samples fabricated with clear glass cullets exhibited threefold NO removal efficiency compared to the samples fabricated with river sand. The light transmittance property of glass was postulated to account for the efficiency improvement, which was confirmed by a separate simulation study. But the influence of the size of glass cullets was not evident. In addition, the photocatalytic activity of concrete surface layers decreased with curing age, showing a loss of 20% photocatalytic activity after 56-day curing.

Use of wasted foundry sand (WFS) as a partial substitute for silica in a soda lime glass; Utilizacao de areia descartada de fundicao (ADF) como substituinte parcial da silica em um vidro soda-cal

Energy Technology Data Exchange (ETDEWEB)

Martin, A.C.; Ueno, O.K.; Folgueras, M.V., E-mail: amandacarolinemartin@gmail.com [Universidade do Estado de Santa Catarina (CCT/UDESC), Joinville, SC (Brazil). Centro de Ciencias Tecnologicas

2016-07-01

The waste foundry sand (WFS) is the main waste generates in foundry industries. Studies in the literature suggest the use of WFS in different materials, such as concrete, brick or asphalt. This work aims to partially replace the silica of a soda-lime glass by the WFS. The waste foundry sand has in its composition elements such as iron and aluminum that can affect the glass quality, which justifies the residue processing to reduce the impurity content. The treatments, that included mechanical agitation and thermal treatment, resulted in a slight decrease in the percent of iron with consequent increase of the silica content. After treatment, some sands were incorporated into the glass, that showed green color but with lower absorption intensity for the sand with less iron content. It was observed that it's possible to obtain glasses using WFS, however, there is difficulty in color controlling. (author.

Effect of γ-irradiation on the electrical conductivity of some soda lime silicate glass containing blast furnace slag

International Nuclear Information System (INIS)

Elalaily, N.A.; Khalil, Magda M.I.; Ahmed, L.S.

2007-01-01

The effect of electric field strength on conduction in soda lime silicate glass doped with blast furnace slag with different concentration was studied and the value of jump distance was calculated. The structure and the mixed anion effect in the conductivity have been examined by measuring the electrical conductivity of glass samples at temperature ranging between 20 and 250 deg. C. The results showed that the electrical conductivity of the examined glasses are divided into three ranges depending on the temperature range. The first is from room temperature to about 49.5 deg. C, the second is at a temperature range of 60.3-104 deg. C where the glass shows a decrease in its conductivity with the increase in temperature. This was followed by another increase in the electrical conductivity with the increase in temperature. The results also showed that the glass becomes more insulating as the slag content increased. The effect of irradiation was also studied by exposing glass samples to two different irradiation doses. It can be noticed that irradiation causes an increase in the electrical conductivity, especially at high temperature. The results were discussed and correlated according to the molecular structure of the prepared glass

Visible light activated catalytic effect of iron containing soda-lime silicate glass characterized by 57Fe-Moessbauer spectroscopy

International Nuclear Information System (INIS)

Shiro Kubuki; Jun Iwanuma; Yusuke Takahashi; Kazuhiko Akiyama; Ernoe Kuzmann; Hungarian Academy of Sciences, Budapest; Tetsuaki Nishida

2014-01-01

A relationship between local structure and visible light activated catalytic effect of iron containing soda lime silicate glass with the composition of 15Na 2 O·15CaO·xFe 2 O 3 ·(70-x)SiO 2 , x = 5-50 mass %, abbreviated as NCFSx was investigated by means of 57 Fe-Moessbauer spectroscopy, X-ray diffractometry (XRD), small angle X-ray scattering (SAXS), electrospray ionization mass spectrometry (ESI-MS) and ultraviolet-visible light absorption spectroscopy (UV-Vis). Moessbauer spectra of NCFSx glass with 'x' being equal to or larger than 30 after isothermal annealing at 1,000 deg C for 100 min consisted of a paramagnetic doublet and a magnetic sextet. The former had isomer shift (δ) of 0.24 mm s -1 and quadrupole splitting (Δ) of 0.99 mm s -1 due to distorted Fe III O 4 tetrahedra, and the latter had δ of 0.36 mm s -1 and internal magnetic field (H int ) of 51.8 T due to hematite (α-Fe 2 O 3 ). The absorption area (A) of α-Fe 2 O 3 varied from 47.2 to 75.9, 93.1, 64.8 and 47.9 % with 'x' from 30 to 35, 40, 45 and 50, indicating that the amount of precipitated α-Fe 2 O 3 varied with the Fe 2 O 3 content of NCFSx glass. The precipitation of α-Fe 2 O 3 was also confirmed by XRD study of annealed NCFS glass with 'x' larger than 30. A relaxed sexted with δ, H int and Γ of 0.34 mm s -1 and 37.9 T and 1.32 mm s -1 was observed from the Moessbauer spectra of annealed NCFSx glass with 'x' of 45 and 50, implying that the precipitation of non-stoichiometric iron hydroxide oxide with the composition of Fe 1.833 (OH) 0.5 O 2.5 having the similar structure of α-Fe 2 O 3 and α-FeOOH. A remarkable decrease in the concentration of methylene blue (MB) from 10 to 0.0 μmol L -1 with the first-order rate constant (k) of 2.87 × 10 -2 h -1 was observed for 10-day leaching test using annealed NCFS50 glass under visible light irradiation. ESI-MS study indicated that existence of fragments with m/z value of 129, 117 and 207 etc. originating from MB having m/z of 284. This

Field demonstration of in situ treatment of buried low-level radioactive solid waste with caustic soda and soda ash to immobilize 90Sr

International Nuclear Information System (INIS)

Spalding, B.P.

1984-02-01

A low-level radioactive solid waste disposal trench was injected on four occasions with solutions of caustic soda, soda ash, caustic soda, and lime/soda ash, respectively. Because investigations had indicated that 90 Sr could be coprecipitated with soil calcium carbonate by treatment with soda ash, this demonstration was undertaken as a test of its technical feasibility. After concentrations of 90 Sr and water hardness decreased within the intratrench monitoring wells; one well at the foot of the trench decreased from over 100 to a persistent level of less than 10 kBq of 90 Sr per liter. Recharge of 90 Sr from the trench to a sump immediately below was reduced by about 90%. Water hardness and 90 Sr concentrations were strongly correlated through time within each monitoring well, indicating that 90 Sr behaved as a tracer for soil calcium and magnesium. The disappearance of 90 Sr from the trench water, therefore, was an in situ water softening. Soil samples retrieved from the trench indicated that as much as 98% of the total 90 Sr was present as a coprecipitate with calcium carbonate. The hydrologic characterization of this trench indicated an average void space of 41% and an average trench-wall hydraulic conductivity of 3.4 x 10 -7 m/s. Sampling of the trench's discharge contamination plume indicated that it had resulted from a combination of subsurface seepage and bathtub overflow during infrequent periods of intense precipitation. A generic assessment of soda ash treatment indicated that treatment would be most effective for soils of high cation exchange capacity with either low ( 80%) basic cation saturation of that cation exchange capacity

The Microstructure and Physical Properties of Incinerated Paper-Cullet-Clay Ceramics

Science.gov (United States)

Sahar, M. R.; Hamzah, K.; Rohani, M. S.; Samah, K. A.; Razi, M. M.

A series of ceramic based on (x) incinerated recycle paper - (80-x) cullet - 20 Kaolin clay (where 10×45 wt%) has successfully been made by slip casting technique followed by sintering at 1000 °C. The actual composition of ceramic is analyzed using Energy Dispersive of X-Ray (EDAX) while the phase existence is determined using X-Ray Diffraction (XRD) technique. Their microstructural morphology is observed under Scanning Electron Microscope (SEM) and the physical properties are measured in term of their thermal shrinkage and hardness. It is found that the ceramic contain mostly of Silica and the phase is dominated by the existence of Quartz (SiO2), Wollastonite (CaSiO3) and Anorthite (Ca(Al2SiO8)). The SEM micrograph shows that the morphology is dominated by the existence of granular structure, and then become smoother as the cullet level is further increased. It is also found out that the thermal shrinkage is in the range 18% - 6.5% while the hardness is in the range of 152MPa- 1.463 GPa depending on composition.

Impact of soda-lime borosilicate glass composition on water penetration and water structure at the first time of alteration

International Nuclear Information System (INIS)

Rebiscoul, D.; Bruguier, F.; Gin, S.; Magnin, V.

2012-01-01

In this study, the impact of soda-lime borosilicate glass composition and particularly the effect of charge compensators such Ca and Na and, of network formers such Si and Zr, on water penetration and water structure at the first time of alteration were investigated. Two non-destructive techniques were combined: the Fourier transform infrared spectroscopy in attenuated total reflection geometry to precise the predominant alteration mechanisms and assess the water structure in altered zone and the grazing incidence X-ray reflectometry to determine the thickness of the altered glass zone allowing to calculate the water diffusion coefficients through the glasses. The results of glass alteration at pH = 3 and 30 degrees C have shown that hydrolysis was the predominant mechanism after few seconds for glass having a high amount of non-binding oxygen. For the other glasses, which for the diffusion was the limiting reaction, the calculated water diffusion coefficients were comprised between 10 -21 and 10 -19 m 2 .s -1 and vary as a function of glass composition. An activation energy of 76.9 kJ.mol -1 was calculated and appears to be higher than inert gas diffusion through the glass highlighting that water molecules strongly interact with the glass matrix. (authors)

The glass-like glazed coating made of cathode-ray tube faceplates cullet

Directory of Open Access Journals (Sweden)

N.І. Zavgorodnya

2016-05-01

Full Text Available The tendency of the current time is to find ways of expedient municipal solid waste recycling as a secondary raw material with similar physicochemical and mechanical characteristics for the purpose of efficient use of resources and reduction of harmful impact on the environment. Due to the termination the production of monitors and television sets with cathode-ray tubes, a significant part of them is grow out of use in the form of dimensional waste. Kinescopes of these electric devices contain valuable components including the screen and conical glass and cathode-luminophors. Existing trends in the world of CRT faceplates cullet recycling argue for reasonability of recycling ways of this valuable secondary raw materials. Aim: The aim of researches is to determine the impact of the full replacement of quartz sand by faceplates cullet and using the zinc sulfide, reconstituted of used cathode-luminophors, as a secondary raw material in the production of glass-like glaze on the basic properties of color glaze. Materials and Methods: Cathode-ray tube faceplates are cut off during removal process, washed from dirt, dried, crushed by press, milled in a cheek grinder and finally crushed in a barrel mill. The slurried impurity (clay, dyes of desired color, including ZnS, water are added to this powder. The received mix is processed of wet grinding for slip production. Slip is surfaced on glass-ceramic tile, dried up, burned at maximum temperature of 900ºС. Results: Experimental research has shown that glass-forming, modifying and intermediate oxides of inorganic substances are added to the glaze with the CRT faceplates cullet. The Chasiv Yar clay belongs to the group with significant gas emission. The water vapor arising during the clay dehydration plays role of the "carrier" of heavy non-volatile components, considerably accelerates gas processes and increases activity of gas components. Zinc sulphide, dissolved in the silicate glaze melts when heated

A study on engineering characteristics of asphalt concrete using filler with recycled waste lime.

Science.gov (United States)

Sung Do, Hwang; Hee Mun, Park; Suk keun, Rhee

2008-01-01

This study focuses on determining the engineering characteristics of asphalt concrete using mineral fillers with recycled waste lime, which is a by-product of the production of soda ash (Na(2)CO(3)). The materials tested in this study were made using a 25%, 50%, 75%, and 100% mixing ratio based on the conventional mineral filler ratio to analyze the possibility of using recycled waste lime. The asphalt concretes, made of recycled waste lime, hydrated lime, and conventional asphalt concrete, were evaluated through their fundamental engineering properties such as Marshall stability, indirect tensile strength, resilient modulus, permanent deformation characteristics, moisture susceptibility, and fatigue resistance. The results indicate that the application of recycled waste lime as mineral filler improves the permanent deformation characteristics, stiffness and fatigue endurance of asphalt concrete at the wide range of temperatures. It was also determined that the mixtures with recycled waste lime showed higher resistance against stripping than conventional asphalt concrete. It was concluded from various test results that a waste lime can be used as mineral filler and, especially, can greatly improve the resistance of asphalt concrete to permanent deformation at high temperatures.

The effects of gamma irradiation on the elastic properties of soda lime glass doped with cerium oxide

Energy Technology Data Exchange (ETDEWEB)

Laopaiboon, R.; Laopaiboon, J.; Pencharee, S. [Glass Technology Excellent Center (GTEC), Department of Physics, Faculty of Science, Ubon Ratchathani University, Ubon Ratchathani, 34190 (Thailand); Nontachat, S. [Department of Radiotherapy, Ubon Ratchathani Cancer Centre, Ubon Ratchathani, 34190 (Thailand); Bootjomchai, C., E-mail: cherdsak_per@hotmail.co.th [Glass Technology Excellent Center (GTEC), Department of Physics, Faculty of Science, Ubon Ratchathani University, Ubon Ratchathani, 34190 (Thailand)

2016-05-05

Soda lime glass doped with cerium oxide was prepared using a conventional melt quenching technique. The density and molar volume of the glass samples were measured. Ultrasonic wave velocities of the glass samples were carried out using a pulse echo technique. The density and ultrasonic velocities were used for determining elastic moduli of the glass samples, both before and after irradiation with gamma rays at 1 kGy. The results revealed that the influence of gamma irradiation caused the matrix structure of the glass samples to be damaged by creating displacements, electronic defects and/or breaks in the network bonds, leading to the formation of non-bridging oxygens (NBOs). Elastic properties were investigated under the influence of gamma irradiation. The results also revealed that the structures of the glass samples were distorted by irradiation. Damage by irradiation created the NBOs and/or the transformation of main glass network structures from Q{sub 4} to Q{sub 3}. Evidence of these results was acquired from FTIR spectra. The results of FTIR supported the results and were obtained from ultrasonic velocities. In addition, the elastic properties obtained from experiments were compared with theoretical values calculated from the Makishima and Mackenzie model (M–M model). - Highlights: • Results show good agreement between experimental and theoretical of elastic moduli. • Influence of irradiation created a distorted network structure. • Transformation of network structure from Ref. Q{sub 4} to Q{sub 3} after irradiation. • FTIR result is good evidence of the result is obtained from ultrasonic technique.

Waste heat recovery at the glass industry with the intervention of batch and cullet preheating

Directory of Open Access Journals (Sweden)

Dolianitis Ioannis

2016-01-01

Full Text Available A promising option to reduce the specific energy consumption and CO2 emissions at a conventional natural gas fired container glass furnace deals with the advanced utilization of the exhaust gases downstream the air regenerators by means of batch and cullet preheating. A 3-dimensional computational model that simulates this process using mass and heat transfer equations inside a preheater has been developed. A case study for an efficient small-sized container glass furnace is presented dealing with the investigation of the impact of different operating and design configurations on specific energy consumption, CO2 emissions, flue gas energy recovery, batch temperature and preheater efficiency. In specific, the effect of various parameters is studied, including the preheater’s dimensions, flue gas temperature, batch moisture content, glass pull, combustion air excess and cullet fraction. Expected energy savings margin is estimated to 12-15%.

Impact effects of gamma irradiation on the optical and FT infrared absorption spectra of some Nd3+-doped soda lime phosphate glasses

Science.gov (United States)

Marzouk, M. A.; Elkashef, I. M.; Elbatal, H. A.

2018-04-01

The main aim of the present work is to study by two collective optical and FTIR spectral measurements some prepared Nd2O3-doped soda lime phosphate glasses before and after gamma irradiation with dose (9 Mrad). The spectral data reveal two strong UV absorption peaks which are correlated with unavoidable trace iron impurities beside extended additional characteristic bands due to Nd3+ ions. Gamma irradiation on the undoped glass produces slight decrease of the intensity of the UV absorption and the generation of an induced visible band and these effects are controlled with two photochemical reduction of some Fe3+ ions to Fe2+ ions together with the formation of nonbridging oxygen hole center (NBOHC) or phosphorous oxygen hole center (POHC). The impact effect of gamma irradiation on the spectra of Nd2O3-doped glasses is limited due to suggested shielding behavior of neodymium ions. FT-infrared spectra show vibrational modes due to main Q2-Q3 phosphate groups and the response of gamma irradiation of the IR spectra is low and the limited variations are related to suggested changes in some bond angles and bond lengths which cause the observed decrease to the intensities of some IR bands.

A simulation approach to material removal in microwave drilling of soda lime glass at 2.45 GHz

Science.gov (United States)

Lautre, Nitin Kumar; Sharma, Apurbba Kumar; Pradeep, Kumar; Das, Shantanu

2015-09-01

Material removal during microwave drilling is basically due to thermal ablation of the material in the vicinity of the drilling tool. The microtip of the tool, also termed as concentrator, absorbs microwaves and ionizes the dielectric in its proximity creating a zone of plasma. The plasma takes the shape of a sphere owing to the atmospheric sphere, which acts as the source of thermal energy to be used for processing a material. This mechanism of heating, also called localized microwave heating, was used in the present study to drill holes in 1.2-mm-thick soda lime glass. The mechanism of material removal had been analyzed through simulation of the hot spot region, and the results were attempted to explain through experiment observations. It was realized that the glass being a poor conductor of heat, a low power (90 W in this case) yields better drilling results owing to more localized heat corresponding to a low-volume plasma sphere. The low application time prevents further heat transfer, and a localized concentration of heat becomes possible that primarily causes the material ablation. The plasma sphere appears sustain while the tool moves through the bulk of the glass thickness although its volume gets further shrunk. The process needs careful selection of the parameters. The simulation results show relatively low temperature in the top half (opposite to the tool tip) of the plasma sphere which eventually causes the semimolten viscous glass to collapse into the drill cavity as the tool advances into the bulk and stops the movement of the tool. The continued plasma sphere raises the tip temperature, which makes the tip to melt and gets blunt. The plasma formation ceases owing to larger diameter of the tool, and the tool gets stuck which could be verified through experimental results.

Numerical study of cullet glass subjected to microwave heating and SiC susceptor effects. Part II: Exergy transfer analysis

International Nuclear Information System (INIS)

Acevedo, Luis; Usón, Sergio; Uche, Javier

2015-01-01

Highlights: • Exergy transfer analysis is proposed for the analysis of microwave glass heating. • Distribution of exergy transferred, accumulated and destroyed is quantified. • The method is applied to the comparison of different susceptor positions. - Abstract: The mathematical model of exergy transfer in cullet glass heated by microwave inside of a cubical cavity with the aid of a susceptor is presented. Part I of this paper presented a numerical combined electromagnetic and heat transfer model by applying both transient Maxwell’s equations and heat transfer equations. Then, the electromagnetic and temperature fields were used to obtain the exergy transfer analysis in the oven. Exergy transfer analysis informs us about the efficiency of energy transformations taking place during the heating process, since it explains how the quality of the energy behaves along the heating process. The rate of internal exergy, exergy flowing and destroyed exergy were obtained and presented for this transient process. Part I showed that the susceptor location could change the temperature fields of cullet glass. So, an exergy analysis is important to understand the irreversibilities produced by a susceptor during preheating (microwaves activation) and heating process of the cullet glass, and how they could be minimized. Exergy transfer analysis shows how both, electromagnetic and heat transfer, are responsible of the irreversibilities generated in the heating process

Comparison studies on soda lignin and soda-anthraquinone lignin

International Nuclear Information System (INIS)

Ibrahim, M.N.M; Yusof, N.N.M.; Hashim, A.

2007-01-01

Soda lignin and soda anthraquinone lignin were compared in this study. The physico-chemical properties and structural features of the isolated lignin were characterized by Fourier Transform Infrared Spectroscopy (FTIR), Ultraviolet (UV), ash test, Carbon-Hydrogen-Nitrogen (CHN) analyzer, Nuclear Magnetic Resonance ( 13 C-NMR) and High Performance Liquid Chromatography (HPLC). Nitrobenzene oxidation was performed on these two types of lignin especially for the HPLC analysis. Based on the CHN, 13 C-NMR and UV results there were no significant differences between soda lignin and soda anthraquinone lignin. The FTIR results also showed that there were no significant differences in terms of functional groups that exist in both lignins. (author)

Large-sized soda ban as an alternative to soda tax.

Science.gov (United States)

Min, Hery Michelle

2013-01-01

This Note examines New York City's Sugary Drinks Portion Cap Rule (Soda Ban), which was originally set to become effective March 12, 2013. The New York County Supreme Court's decision in New York Statewide Coalition of Hispanic Chambers of Commerce v. New York City Department of Health and Mental Hygiene suspended the Soda Ban on March 11, 2013. The First Department of the Appellate Division of New York State Supreme Court affirmed the suspension on July 30, 2013. However, the complex economic policy and constitutional issues arising from the proposed Soda Ban deserve as much attention as the ultimate result of the legal challenge to the ban. Both courts struck down the Soda Ban on the grounds that it violated the separation of powers doctrine. The lower court further held that the Soda Ban was arbitrary and capricious. This Note does not focus solely on the holdings of the two courts, but takes a broader approach in analyzing the issues involved in the Soda Ban. By comparing and contrasting tobacco products with sugary beverages, this Note explains why the public seems to find the Soda Ban less appealing than tobacco regulations. Specifically, this Note addresses how the failed attempts of numerous states and cities to implement soda taxes demonstrate the complexity of policies geared toward curbing obesity; how fundamental values, such as health, fairness, efficiency, and autonomy factor into obesity policies; and the fact that legislatures and courts are struggling to determine the scope of public health law intervention. The Note explores how the Soda Ban, despite its judicial suspension, could represent a stepping-stone in combating the obesity epidemic.

Papermaking Properties of Carpinus betulus with kraft, Soda and Soda-Urea Pulping Processes

Directory of Open Access Journals (Sweden)

Rasoul Darstan

2013-06-01

Full Text Available This research was carried out in order to comparatively investigate the hornbeam kraft, soda and soda-urea papermaking properties. The selected treatment in kraft process had an average yield of 44.43% and kappa number of 23.75. In soda process the selected treatment had an average yield of 38.75% and kappa number of 19.28. In soda-urea process, the selected treatments had an average yield of 39.85, 40.1, 40.5, 39.8 and 40.61 and kappa number of 21.21, 22.33, 22.66, 25.28 and 26.85. After refining the selected pulp to reach the freeness of 400±25 ml CSF, 60 g/m2 handsheets were made and physical, mechanical and optical properties were measured. Results showed that kraft pulps had higher yield and better refinability than soda and soda-urea pulps. Papers made from kraft process had higher strength properties than those made of soda and soda-urea process. With addition of urea, yield and kappa number of pulps increased. The highest improvement in tensile index, breaking length and tear index was achieved with addition of 3% urea and the highest improvement in burst index was achieved with adding 4% urea. Results of brightness measurements showed that papers from kraft and soda processes had the lowest and highest brightness degree respectively. With the addition of urea, brightness of papers decreased.

A comparison of soda and soda-AQ pulps from cotton stalks | Akgül ...

African Journals Online (AJOL)

In this study, cotton stalks (Gossypium hirsutum L.) were cooked using soda and soda-anthraquinone (AQ) process. Nine soda cooks were conducted by changing cooking conditions including active alkali charge and pulping time. Soda-AQ cooks were obtained by adding 0.075, 0.10, 0.15, 0.2% AQ (based on o.d stalks) to ...

Waste heat recovery at the glass industry with the intervention of batch and cullet preheating

OpenAIRE

Dolianitis Ioannis; Giannakopoulos Dionysios; Hatzilau Christina-Stavrula; Karellas Sotirios; Kakaras Emmanuil; Nikolova Evelina; Skarpetis Georgios; Christodoulou Nikolaos; Giannoulas Nikolaos; Zitounis Theodoros

2016-01-01

A promising option to reduce the specific energy consumption and CO2 emissions at a conventional natural gas fired container glass furnace deals with the advanced utilization of the exhaust gases downstream the air regenerators by means of batch and cullet preheating. A 3-dimensional computational model that simulates this process using mass and heat transfer equations inside a preheater has been developed. A case study for an efficient small-sized containe...

ZnO films grown by pulsed-laser deposition on soda lime glass substrates for the ultraviolet inactivation of Staphylococcus epidermidis biofilms

Directory of Open Access Journals (Sweden)

Jean-Paul Mosnier, Richard J O'Haire, Enda McGlynn, Martin O Henry, Stephen J McDonnell, Maria A Boyle and Kevin G McGuigan

2009-01-01

Full Text Available We found that a ZnO film of 2 μm thickness which was laser-deposited at room temperature onto a plain soda lime glass substrate, exhibits notable antibacterial activity against a biofilm of Staphylococcus epidermidis when back-illuminated by a UVA light source with a peak emission wavelength of about 365 nm. X-ray diffraction (XRD, scanning electron microscopy (SEM, atomic force microscopy (AFM, UV-visible absorption spectroscopy, Raman spectroscopy and x-ray photoemission spectroscopy (XPS were used to characterize the ZnO films before and after the interactions with the biofilm and the ultraviolet light, respectively. The as-deposited film was highly textured with the wurtzite (0002 in-plane orientation (c-axis perpendicular to ZnO surface and had a surface rms roughness of 49.7 nm. In the as-deposited film, the Zn to O ratio was 1 to 0.95. After the UV and biofilm treatments, the ZnO film surface had become rougher (rms roughness 68.1 nm and presented uniform micron-sized pitting randomly distributed, while the zinc to oxygen ratio had become 1 to 2.2. In this case, both the UV-visible and Raman spectra pointed to degradation of the structural quality of the material. On the strength of these data, we propose a model for the mediation of the bactericidal activity in which the photogeneration of highly oxidizing species and the presence of active surface defect sites both play an important role. This study is of particular interest for the acute problem of disinfection of pathogenic biofilms which form on medical device/implant surfaces.

Citrate, malate and alkali content in commonly consumed diet sodas: implications for nephrolithiasis treatment.

Science.gov (United States)

Eisner, Brian H; Asplin, John R; Goldfarb, David S; Ahmad, Ardalanejaz; Stoller, Marshall L

2010-06-01

Citrate is a known inhibitor of calcium stone formation. Dietary citrate and alkali intake may have an effect on citraturia. Increasing alkali intake also increases urine pH, which can help prevent uric acid stones. We determined citrate, malate and total alkali concentrations in commonly consumed diet sodas to help direct dietary recommendations in patients with hypocitraturic calcium or uric acid nephrolithiasis. Citrate and malate were measured in a lemonade beverage commonly used to treat hypocitraturic calcium nephrolithiasis and in 15 diet sodas. Anions were measured by ion chromatography. The pH of each beverage was measured to allow calculation of the unprotonated anion concentration using the known pK of citric and malic acid. Total alkali equivalents were calculated for each beverage. Statistical analysis was done using Pearson's correlation coefficient. Several sodas contained an amount of citrate equal to or greater than that of alkali and total alkali as a lemonade beverage commonly used to treat hypocitraturic calcium nephrolithiasis (6.30 mEq/l citrate as alkali and 6.30 as total alkali). These sodas were Diet Sunkist Orange, Diet 7Up, Sprite Zero, Diet Canada Dry Ginger Ale, Sierra Mist Free, Diet Orange Crush, Fresca and Diet Mountain Dew. Colas, including Caffeine Free Diet Coke, Coke Zero, Caffeine Free Diet Pepsi and Diet Coke with Lime, had the lowest total alkali (less than 1.0 mEq/l). There was no significant correlation between beverage pH and total alkali content. Several commonly consumed diet sodas contain moderate amounts of citrate as alkali and total alkali. This information is helpful for dietary recommendations in patients with calcium nephrolithiasis, specifically those with hypocitraturia. It may also be useful in patients with low urine pH and uric acid stones. Beverage malate content is also important since malate ingestion increases the total alkali delivered, which in turn augments citraturia and increases urine pH. Copyright

Baking Soda Science.

Science.gov (United States)

Science Activities, 1994

1994-01-01

Discusses the basic principles of baking soda chemistry including the chemical composition of baking soda, its acid-base properties, the reaction of bicarbonate solution with calcium ions, and a description of some general types of chemical reactions. Includes a science activity that involves removing calcium ions from water. (LZ)

The Sr-90 waste treatment by using sodium carbonat as a carrier

International Nuclear Information System (INIS)

Suroto.

1978-01-01

The coprecipitation processes of the Sr-90 wastes, with the lime-soda treatment, that followed by the mechanism of isomorph substitution, have shown a good performance in pH 7-8. Excess of natrium carbonate in the lime-soda treatment caused the decrease of the decontamination factor. This research shows that the coprecipitation by calcite-phosphate was better than the lime-soda treatment. (author)

Potential Use Of Carbide Lime Waste As An Alternative Material To Conventional Hydrated Lime Of Cement-Lime Mortars

OpenAIRE

Al Khaja, Waheeb A.

1992-01-01

The present study aimed at the possibility of using the carbide lime waste as an alternative material to the conventional lime used for cement-lime mortar. The waste is a by-product obtained in the generation of acetylene from calcium carbide. Physical and chemical properties of the wastes were studied. Two cement-lime-sand mix proportions containing carbide lime waste were compared with the same mix proportions containing conventional lime along with a control mix without lime. Specimens wer...

A Novel Study on Using Vietnam Rice Hush Ash and Cullet as Environmental Materials

Directory of Open Access Journals (Sweden)

Trung Kien Pham

2017-01-01

Full Text Available This work introduces novel method to prepare ecomaterials wollastonite (CaSiO3 using the hydrothermal treatment technique of Rice hush ash (RHA, glass cullet and CaO at 180°C for 24 hour so as the Ca/Si molar ration of 1.0. The sample after hydrothermal treatment at 180°C for 24 hours is calcined at 1000°C to obtained wollastonite CaSiO3. The obtained wollastonite has many applications in biomaterials and thermal insulator. This research also aim to improve the quality of RHA, thus reduce negative impact to environment.

Novel radiator for carbon dioxide absorbents in low-flow anesthesia.

Science.gov (United States)

Hirabayashi, Go; Mitsui, Takanori; Kakinuma, Takayasu; Ogihara, Yukihiko; Matsumoto, Shohei; Isshiki, Atsushi; Yasuo, Watanabe

2003-01-01

During long-term low-flow sevoflurane anesthesia, dew formation and the generation of compound A are increased in the anesthesia circuit because of elevated soda lime temperature. The object of this study was to develop a novel radiator for carbon dioxide absorbents used for long durations of low-flow sevoflurane anesthesia. Eleven female swine were divided into two groups comprising a "radiator" group (n = 5) that used a novel radiator for carbon dioxide absorbents and a "control" group (n = 6) that used a conventional canister. Anesthesia was maintained with N2O, O2, and sevoflurane, and low-flow anesthesia was performed with fresh gas flow at 0.6 L/min for 12 hr. In the "control" group, the soda lime temperature reached more than 40 degrees C and soda lime dried up with severe dew formation in the inspiratory valve. In the "radiator" group, the temperature of soda lime stayed at 30 degrees C, and the water content of soda lime was retained with no dew formation in the inspiratory valve. In addition, compound A concentration was reduced. In conclusion, radiation of soda lime reduced the amounts of condensation formed and the concentration of compound A in the anesthetic circuit, and allowed long term low-flow anesthesia without equipment malfunction.

Antibacterial activity of baking soda.

Science.gov (United States)

Drake, D

1997-01-01

The antibacterial activity of baking soda (sodium bicarbonate) was assessed using three different experimental approaches. Standard minimum inhibitory concentration analyses revealed substantial inhibitory activity against Streptococcus mutans that was not due to ionic strength or high osmolarity. Short-term exposure assays showed significant killing of bacterial suspensions when baking soda was combined with the detergent sodium dodecylsulfate. Multiple, brief exposures of sucrose-colonized S mutans to baking soda and sodium dodecylsulfate caused statistically significant decreases in numbers of viable cells. Use of oral health care products with high concentrations of baking soda could conceivably result in decreased levels of cariogenic S mutans in saliva and plaque.

Sorption Characteristics of Activated Carbon Obtained from Rice Husks by Treatment with Lime

International Nuclear Information System (INIS)

Hnin Nwe Aye; Aye Aye Maw; Nyunt Wynn

2011-12-01

The sorption studies of rice husk char prepared by carbonization and activation with lime, caustic soda and sulphuric acid have been investigated. Prior to impregnation with the lime; on a micro processing scale the pre-carbonization temperature of rice husk were determined by using TG-DTA thermal analysis. The impregnation with chemical was made after carbonization and the impregnated chars were subjected to activation at appropriate temperatures of about 300 C to 500 C depending on the impregnated chars. The physico-chemical properties of the prepared chars were tested by conventional and modern techniques. Sorption capacities with respect to colored dyes were determined for each of the char. These sorption capacities are indicative of the decolorizing nature and the acid or basic nature. The sorption capacities of the prepared chars towards the uptake of metals such as copper, iron, lead and cadmium were also studied and the lime activated char exhibits high adsorptive capacities for all the metals compared to other prepared chars as well as the commercial wood char. The evaluation of the sorption capacities of this chars were made on the basis of Freundlich and Langmuir monolayer coverage equations. Thus, based on batch dosage method and breakthrough flow method, the uptake of the metals were found to be in following order for the lime activated rice husk char; Cu > Fe > Pb > Cd. From this investigation, it can be inferred that a rice husk char impregnated with 20% technical grade CaO has the potential effect to be used as an effective metal adsorbent particularly for the uptake of toxic heavy metals in the secondary stage of water treatment processes.

Hemorrhagic Encephalopathy From Acute Baking Soda Ingestion.

Science.gov (United States)

Hughes, Adrienne; Brown, Alisha; Valento, Matthew

2016-09-01

Baking soda is a readily available household product composed of sodium bicarbonate. It can be used as a home remedy to treat dyspepsia. If used in excessive amounts, baking soda has the potential to cause a variety of serious metabolic abnormalities. We believe this is the first reported case of hemorrhagic encephalopathy induced by baking soda ingestion. Healthcare providers should be aware of the dangers of baking soda misuse and the associated adverse effects.

Use of rice rusk ash and spent catalyst as a source of raw material for the production and characterization of soda-lime silicate glasses destined for packaging

International Nuclear Information System (INIS)

Araujo, Mariana Silva de

2016-01-01

In this study, the use of two industrial solid wastes (ISW), generated in large quantities in Brazil, were presented in production of soda-lime silicate glasses destined for packaging. The evaluated wastes were rice husk ash (RHA) and the spent catalyst at the Petrochemical Fluid Catalytic Cracking units (ECAT), both may be classified as a class II solid waste according to NBR 10.004. This new proposal for the allocation of such wastes is an alternative to current provisions, seeking not only to minimize environmental impacts, but also enrich them as raw materials. For the samples production, besides ISW were used melting oxide (Na 2 CO 3 ) and stabilizer oxide (CaO).The results demonstrate that both can be used in their raw form (without treatment) replacing important raw materials, sources of Al 2 O 3 and SiO 2 , essential for glass formation. The samples obtained presented amber color due to the presence of nickel (Ni² + ion) from ECAT and 18% of optical transmittance. They also showed a good homogeneity, i.e., absence of bubbles and striae and 1,33 x 10 -8 g/cm²·day of hydrolytic resistance according to ISO695-1984. Thus, the obtained glass is suitable for applications requiring low light transmittance such as colored glasses containers in general, which does not require perfect visibility and transparency. The incorporation in the final composition was approximately 78% in mass. (author)

Hemorrhagic Encephalopathy From Acute Baking Soda Ingestion

Directory of Open Access Journals (Sweden)

Adrienne Hughes

2016-09-01

Full Text Available Baking soda is a readily available household product composed of sodium bicarbonate. It can be used as a home remedy to treat dyspepsia. If used in excessive amounts, baking soda has the potential to cause a variety of serious metabolic abnormalities. We believe this is the first reported case of hemorrhagic encephalopathy induced by baking soda ingestion. Healthcare providers should be aware of the dangers of baking soda misuse and the associated adverse effects.

Hemorrhagic Encephalopathy From Acute Baking Soda Ingestion

OpenAIRE

Hughes, Adrienne; Brown, Alisha; Valento, Matthew

2016-01-01

Baking soda is a readily available household product composed of sodium bicarbonate. It can be used asa home remedy to treat dyspepsia. If used in excessive amounts, baking soda has the potential to causea variety of serious metabolic abnormalities. We believe this is the first reported case of hemorrhagicencephalopathy induced by baking soda ingestion. Healthcare providers should be aware of the dangers ofbaking soda misuse and the associated adverse effects. [West J Emerg Med. 2016;17(5)619...

Functional microbiology of soda lakes

NARCIS (Netherlands)

Sorokin, D.Y.; Banciu, H.L.; Muyzer, G.

2015-01-01

Soda lakes represent unique permanently haloalkaline system. Despite the harsh conditions, they are inhabited by abundant, mostly prokaryotic, microbial communities. This review summarizes results of studies of main functional groups of the soda lake prokaryotes responsible for carbon, nitrogen and

LIME REQUIREMENT DETERMINATION AND LIMING IMPACT ON SOIL NUTRIENT STATUS

Directory of Open Access Journals (Sweden)

Krunoslav Karalić

2010-06-01

Full Text Available The aim of conducted research was to determine the influence of liming, mineral and organic fertilization on soil chemical properties and nutrient availability in the soil, yield height and mineral composition of alfalfa. Results were used to create regression models for prediction of liming impact on soil chemical properties. Liming and fertilization experiment was sat up in 20 L volume plastic pots with two types of acid soils with different texture from two sites. Ten liming and fertilization treatments were applied in four repetitions. Lime treatments increased soil pH values and decreased hydrolytic acidity. Mineral and organic fertilization affected additional soil acidification. Application of lime intensified mineralization and humus decomposition, while organic fertilization raised humus content. The results showed significant increase of AL-P2O5 and K2O availability. The treatments increased soil Ca concentrations, but at the same time decreased exchangeable Mg concentrations. Soil pH increase resulted in lower Fe, Mn, Zn and Cu availability. Soil CEC was increased by applied treatments. Lime rates increased number and height of alfalfa plants, as well as yield of leaf, stalk increased concentrations of N, P, K and Ca in alfalfa leaf and stalk, but decreased leaf Mg and Fe, Mn, Zn and Cu concentrations. Regression computer models predicted with adequate accuracy P, Fe, Mn, Zn and Cu availability and final pH value as a result of liming and fertilization impact.

SODA: Smart Objects, Dumb Archives

Science.gov (United States)

Nelson, Michael L.; Maly, Kurt; Zubair, Mohammad; Shen, Stewart N. T.

2004-01-01

We present the Smart Object, Dumb Archive (SODA) model for digital libraries (DLs). The SODA model transfers functionality traditionally associated with archives to the archived objects themselves. We are exploiting this shift of responsibility to facilitate other DL goals, such as interoperability, object intelligence and mobility, and heterogeneity. Objects in a SODA DL negotiate presentation of content and handle their own terms and conditions. In this paper we present implementations of our smart objects, buckets, and our dumb archive (DA). We discuss the status of buckets and DA and how they are used in a variety of DL projects.

Lime-water consolidation effects on poor lime mortars

Czech Academy of Sciences Publication Activity Database

Drdácký, Miloš; Slížková, Zuzana

2012-01-01

Roč. 43, č. 1 (2012), s. 31-36 ISSN 0044-9466 R&D Projects: GA ČR(CZ) GA103/09/2067 Institutional support: RVO:68378297 Keywords : lime mortar s * lime -water consolidation * conservation Subject RIV: JN - Civil Engineering

Lime

Science.gov (United States)

Miller, M.

2006-01-01

In 2005, US lime production was 20 Mt with a value of $1.5 billion. Production was unchanged compared with 2004. Captive production was 1.4 Mt. US consumption was 20.2 Mt. Most of the US lime trade was with Canada and Mexico. Despite some disruptions due to hurricanes Katrina and Rita, normal sales activities remained healthy.

Characterization of residues of effluent treatment plant from lapping process of soda-lime glass and its application in the production of concrete; Caracterizacao de residuo de estacao de tratamento de efluentes de processo de lapidacao de vidro sodo-calcico e sua aplicacao na producao de concreto

Energy Technology Data Exchange (ETDEWEB)

Antonio, Aline Pignaton; Calmon, Joao Luiz; Tristao, Fernando Avancini, E-mail: apignaton@hotmail.com, E-mail: calmonbarcelona@gmail.com, E-mail: fernandoavancini@ct.ufes.br [Universidade Federal do Espirito Santo (UFES), Vitoria, ES (Brazil). Programa de Pos-Graduacao em Engenharia Civil

2012-07-01

This study enunciates the physical, chemical and mineralogical composition of the residue from the process of ETE cutting of soda-lime glasses and its application in concrete as a replacement to the weight of CPV ARI RS cement, at levels of 0, 5, 10, 15 and 20%. Tests were performed on fresh and hardened (ages 3, 7, 28 and 300 days). The results were compared and statistically analyzed. In the fresh state, reductions in the amount of exuding water and consistency were observed. The results of compressive strength were statistically different, while the results for the tensile strength by diametrical compression and modulus of elasticity results were belonging to homogeneous groups. Beneficial effects the levels of residue on the cementitious matrix and the transition zone of concrete were identified by SEM, particularly concrete in S15.

Exposure to soda commercials affects sugar-sweetened soda consumption in young women. An observational experimental study

NARCIS (Netherlands)

Koordeman, R.; Anschutz, D.J.; Baaren, R.B. van; Engels, R.C.M.E.

2010-01-01

The present study examines the direct effects of television commercials advertising soda on actual sugar-sweetened soda consumption among young women. An experimental-observational study design was used, in which 51 female students (ages 18-29) were exposed to a 35-min movie clip, interrupted by two

Exposure to soda commercials affects sugar-sweetened soda consumption in young woman: an observational experimental study

NARCIS (Netherlands)

Koordeman, R.; Anschutz, D.J.; van Baaren, R.B.; Engels, R.C.M.E.

2010-01-01

The present study examines the direct effects of television commercials advertising soda on actual sugar-sweetened soda consumption among young women. An experimental-observational study design was used, in which 51 female students (ages 18-29) were exposed to a 35-min movie clip, interrupted by two

Synthesis of glass-ceramics using glass cullet and vitrified industrial by-products

Energy Technology Data Exchange (ETDEWEB)

Karamberi, A.; Orkopoulos, K.; Moutsatsou, A. [National Technical University of Athens, Athens (Greece)

2007-07-01

This study concerns the recycling of inorganic waste materials for the production of glass-ceramics and the evaluation of the developed physical properties. Four industrial by-products were selected due to their mass production: (I) two high calcium lignite fly ashes, (ii) slag derived from the production of Fe-Ni and, (iii) steel slag. In order to examine the role of the SiO{sub 2} in the crystallization process, glass cullet and Egyptian sand were added. Thermal treatment, at 1450{sup o}C, enables the production of glasses using mixtures of these materials at appropriate proportions. The crystallization was achieved by heating at 900, 950 and 1000{sup o}C. The produced materials were examined concerning their structure by X-ray diffraction and scanning electron microscopy (SEM-EDS). The results showed that the crystalline phase is greatly depending on the structure of the raw material and the thermal process, influencing accordingly the hardness of the final products.

The antifungal efficiency of carbide lime slurry compared with the commercial lime efficiency

Science.gov (United States)

Strigac, J.; Mikusinec, J.; Strigacova, J.; Stevulova, N.

2017-10-01

The article deals with studying the antifungal efficiency of carbide lime slurry compared to industrially manufactured commercial lime. Antifungal efficiency expressed as mould proofness properties was tested on the fungi using the procedure given in standard CSN 72 4310. A mixture of fungi Aspergillus niger, Chaetomium globosum, Penicillium funiculosum, Paecilomyces variotii and Gliocladium virens was utilized for testing. The scale for evaluating mould proofness properties according to CSN 72 4310 is from 0 to 5 in degree of fungi growth, where 0 means that no fungi growth occurs and the building products and materials possess fungistatic properties. The study confirms the fungistatic propeties of carbide lime slurry as well as industrially manufactured commercial lime. However, carbide lime slurry and industrially manufactured commercial lime possess no fungicidal effect.

[Review of lime carbon sink.

Science.gov (United States)

Liu, Li Li; Ling, Jiang Hua; Tie, Li; Wang, Jiao Yue; Bing, Long Fei; Xi, Feng Ming

2018-01-01

Under the background of "missing carbon sink" mystery and carbon capture and storage (CCS) technology development, this paper summarized the lime material flow process carbon sink from the lime carbonation principles, impact factors, and lime utilization categories in chemical industry, metallurgy industry, construction industry, and lime kiln ash treatment. The results showed that the lime carbonation rate coefficients were mainly impacted by materials and ambient conditions; the lime carbon sink was mainly in chemical, metallurgy, and construction industries; and current researches focused on the mechanisms and impact factors for carbonation, but their carbon sequestration calculation methods had not been proposed. Therefore, future research should focus on following aspects: to establish a complete system of lime carbon sequestration accounting method in view of material flow; to calculate lime carbon sequestration in both China and the world and explain their offset proportion of CO 2 emission from lime industrial process; to analyze the contribution of lime carbon sequestration to missing carbon sink for clarifying part of missing carbon sinks; to promote the development of carbon capture and storage technology and provide some scientific bases for China's international negotiations on climate change.

Dolomitic lime containing hydraulic additive

International Nuclear Information System (INIS)

Lagzdina, S.; Sedmalis, U.; Bidermanis, L.; Liepins, J.; Grosvalds, I.

1997-01-01

To obtain qualitative dolomitic lime the optimum calcination temperature of dolomite containing about 9 % of clayey substances is 900 deg C. The mechanical strength of dolomitic lime containing 30 % of brick waste additive after 6-9 months of hardening is 1.4-1.5 times higher than that of samples without hydraulic additive, for calcium lime - 2.2-2.6 times higher. Generally the mechanical strength of dolomitic lime is higher than that one of calcium lime. It can be explained by the active role of MgO in the hydration and hardening processes of dolomitic lime. Xray diffraction phase analysis was performed by X-ray diffractometer DPON-3M with Cu-K α emission filter

An Analysis of the Nonlinear Spectral Mixing of Didymium and Soda-Lime Glass Beads Using Hyperspectral Imagery (HSI) Microscopy

Science.gov (United States)

2014-05-01

2001). Learning with Kernels: Support Vector Machines , Regularization, Optimization, and Beyond. The MIT Press, Cambridge, MA, 644 p. [26] Banerjee...A., Burlina, P., and Broadwater, J., (2007). A Machine Learning Approach for finding hyperspectral endmembers. Proceedings of the IEEE International... lime glass beads using hyperspectral imagery (HSI) microscopy Ronald G. Resmini1*, Robert S. Rand2, David W. Allen3, and Christopher J. Deloye1

The effect of soda immersion on nano hybrid composite resin discoloration

Directory of Open Access Journals (Sweden)

M. Chair Effendi

2014-03-01

Full Text Available Background: Composite resin is the tooth-colored restorative material which most of the people are fond of due to their aesthetic value. The composite resin discoloration may happen because of the intrinsic and extrinsic factors. Soda water is one of the beverages which can cause the composite resin discoloration. Purpose: The study was aimed to determine the effect of soda immersion on nano hybrid composite resin discoloration. Methods: The study was an experimental laboratory study using 100 shade A3 nano hybrid composite resin specimens with the diameter of 5 mm and density of 2mm. The samples were divided into 5 groups, each group was immersed in different beverages. The beverages were mineral water; lemon-flavored soda; strawberry-flavored soda; fruit punch-flavored soda; and orange-flavored soda for 3, 7, 14 and 21 days respectively, in the temperature of 37o C. The discoloration measurement utilizes Spectrophotometer, Vita Easy Shade, and uses CIEL*a*b* method. Results: The result showed that the duration of immersion in soda had an effect on the Nano hybrid composite resin discoloration. Strawberry and fruit punch- flavored soda were the most influential components toward the discoloration. Nevertheless, the generally-occurred discoloration was clinically acceptable (∆E ≤ 3,3. Conclusion: The study suggested that the soda immersion duration has effect on Nano hybrid composite resin discoloration.Latar belakang: Resin komposit adalah material sewarna gigi yang diminati masyarakat karena memiliki nilai estetik yang baik. Perubahan warna resin komposit dapat terjadi karena faktor intrinsik dan ekstrinsik. Minuman soda merupakan salah satu minuman yang dapat menyebabkan perubahan warna pada resin komposit. Tujuan: Tujuan dari penelitian ini untuk meneliti perubahan warna resin komposit nanohibrida akibat perendaman dalam minuman soda. Metode: Metode yang digunakan pada penelitian ini adalah eksperimental laboratorik dengan menggunakan

Preparation and Characterization of Modified Soda Lignin with Polyethylene Glycol

Directory of Open Access Journals (Sweden)

Fangda Zhang

2016-10-01

Full Text Available Soda lignin does not have thermal flowing characteristics and it is impossible for it to be further thermally molded. To achieve the fusibility of soda lignin for fiber preparation by melt-spinning, an effective method for soda lignin modification was conducted by cooking it with polyethylene glycol (PEG 400 at various ratios. The higher the ratio of PEG that was used, the more PEG molecular chains were grafted at the alpha carbon of the soda lignin through ether bonds, resulting in lower thermal transition temperatures and more excellent fusibility. The modified soda lignin with a weight ratio of lignin to PEG of 1:4 exhibited a relative thermal stability of molten viscosity at selected temperatures. Thereafter, the resultant fusible soda lignin was successfully melt-spun into filaments with an average diameter of 33 ± 5 μm, which is smaller than that of some industrial lignins. Accordingly, it is possible to utilize soda lignin to produce fibrous carbonaceous materials.

β-Irradiation Effects on the Formation and Stability of CaMoO4 in a Soda Lime Borosilicate Glass Ceramic for Nuclear Waste Storage.

Science.gov (United States)

Patel, Karishma B; Boizot, Bruno; Facq, Sébastien P; Lampronti, Giulio I; Peuget, Sylvain; Schuller, Sophie; Farnan, Ian

2017-02-06

Molybdenum solubility is a limiting factor to actinide loading in nuclear waste glasses, as it initiates the formation of water-soluble crystalline phases such as alkali molybdates. To increase waste loading efficiency, alternative glass ceramic structures are sought that prove resistant to internal radiation resulting from radioisotope decay. In this study, selective formation of water-durable CaMoO 4 in a soda lime borosilicate is achieved by introducing up to 10 mol % MoO 3 in a 1:1 ratio to CaO using a sintering process. The resulting homogeneously dispersed spherical CaMoO 4 nanocrystallites were analyzed using electron microscopy, X-ray diffraction (XRD), Raman and electron paramagnetic resonance (EPR) spectroscopies prior to and post irradiation, which replicated internal β-irradiation damage on an accelerated scale. Following 0.77 to 1.34 GGy of 2.5 MeV electron radiation CaMoO 4 does not exhibit amorphization or significant transformation. Nor does irradiation induce glass-in-glass phase separation in the surrounding amorphous matrix, or the precipitation of other molybdates, thus proving that excess molybdenum can be successfully incorporated into a structure that it is resistant to β-irradiation proportional to 1000 years of storage without water-soluble byproducts. The CaMoO 4 crystallites do however exhibit a nonlinear Scherrer crystallite size pattern with dose, as determined by a Rietveld refinement of XRD patterns and an alteration in crystal quality as deduced by anisotropic peak changes in both XRD and Raman spectroscopy. Radiation-induced modifications in the CaMoO 4 tetragonal unit cell occurred primarily along the c-axis indicating relaxation of stacked calcium polyhedra. Concurrently, a strong reduction of Mo 6+ to Mo 5+ during irradiation is observed by EPR, which is believed to enhance Ca mobility. These combined results are used to hypothesize a crystallite size alteration model based on a combination of relaxation and diffusion

Baking soda: a potentially fatal home remedy.

Science.gov (United States)

Nichols, M H; Wason, S; Gonzalez del Rey, J; Benfield, M

1995-04-01

We present a case of a six-week-old infant who developed life-threatening complications after unintentional sodium bicarbonate intoxication. Baking soda was being used by the mother as a home remedy to "help the baby burp." A review of the literature regarding the use (or misuse) of baking soda follows. Our patient, along with the other noted case reports, emphasizes the need for warnings on baking soda products whose labels recommend its use as an antacid. Poisonings must be high in the differential diagnosis of any patient, regardless of age, who presents with altered mental status or status epilepticus.

Sponsorship of National Health Organizations by Two Major Soda Companies.

Science.gov (United States)

Aaron, Daniel G; Siegel, Michael B

2017-01-01

Obesity is a pervasive public health problem in the U.S. Reducing soda consumption is important for stemming the obesity epidemic. However, several articles and one book suggest that soda companies are using their resources to impede public health interventions that might reduce soda consumption. Although corporate sponsorship by tobacco and alcohol companies has been studied extensively, there has been no systematic attempt to catalog sponsorship activities of soda companies. This study investigates the nature, extent, and implications of soda company sponsorship of U.S. health and medical organizations, as well as corporate lobbying expenditures on soda- or nutrition-related public health legislation from 2011 to 2015. Records of corporate philanthropy and lobbying expenditures on public health legislation by soda companies in the U.S. during 2011-2015 were found through Internet and database searches. From 2011 to 2015, the Coca-Cola Company and PepsiCo were found to sponsor a total of 95 national health organizations, including many medical and public health institutions whose specific missions include fighting the obesity epidemic. During the study period, these two soda companies lobbied against 29 public health bills intended to reduce soda consumption or improve nutrition. There is surprisingly pervasive sponsorship of national health and medical organizations by the nation's two largest soda companies. These companies lobbied against public health intervention in 97% of cases, calling into question a sincere commitment to improving the public's health. By accepting funding from these companies, health organizations are inadvertently participating in their marketing plans. Copyright © 2016 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Bubbling over: soda consumption and its link to obesity in California.

Science.gov (United States)

Babey, Susan H; Jones, Malia; Yu, Hongjian; Goldstein, Harold

2009-09-01

Background The prevalence of overweight and obesity has increased dramatically in both adults and children in the last three decades in the n California, 62% of adolescents ages 12-17 and 41% of children ages 2-11 drink at least one soda or other sweetened beverage every day. In addition, 24% of adults drink at least one soda or other sweetened beverage on an average day. Adults who drink soda occasionally (not every day) are 15% more likely to be overweight or obese, and adults who drink one or more sodas per day are 27% more likely to be overweight or obese than adults who do not drink soda, even when adjusting for poverty status and race/ethnicity. This policy brief, produced collaboratively by the California Center for Public Health Advocacy and the UCLA Center for Health Policy Research, examines soda consumption in California by cities and counties using data from the 2005 California Health Interview Survey (CHIS 2005). In addition, the brief investigates whether there is an association between soda consumption and the prevalence of overweight and obesity. There are major differences in soda consumption rates by geographic area in California, suggesting that social and environmental factors affect the consumption of soda. Also, the prevalence of overweight and obesity is higher among those who drink one or more sodas or other sweetened beverages every day than among those who do not consume these soft drinks. Establishing public policies that focus on reducing soda consumption could contribute to reversing California's increasing overweight and obesity problem.

Fabrication of low thermal expansion SiC/ZrW{sub 2}O{sub 8} porous ceramics

Energy Technology Data Exchange (ETDEWEB)

Poowancum, A; Matsumaru, K; Juarez-Ramirez, I; Ishizaki, K [Department of Mechanical Engineering, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka, Niigata 940-2188 (Japan); Torres-Martinez, L M [Universidad Autonoma de Nuevo Leon, Av. Universidad s/n, San Nicolas de los Garza, NL, C.P. 66451 (Mexico); Fu, Z Y [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan, Hubei, 430070 (China); Lee, S W, E-mail: anurat@ishizaki.nagaokaut.ac.jp [Department of Environment Engineering, Sun Moon University, 100, Kalsan-ri, Tangjeong-myeon, Asan, Chungnam 336-708 (Korea, Republic of)

2011-03-15

Low or zero thermal expansion porous ceramics are required for several applications. In this work near zero thermal expansion porous ceramics were fabricated by using SiC and ZrW{sub 2}O{sub 8} as positive and negative thermal expansion materials, respectively, bonded by soda lime glass. The mixture of SiC, ZrW{sub 2}O{sub 8} and soda lime glass was sintered by Pulsed Electric Current Sintering (PECS, or sometimes called Spark Plasma Sintering, SPS) at 700 deg. C. Sintered samples with ZrW{sub 2}O{sub 8} particle size smaller than 25 {mu}m have high thermal expansion coefficient, because ZrW{sub 2}O{sub 8} has the reaction with soda lime glass to form Na{sub 2}ZrW{sub 3}O{sub 12} during sintering process. The reaction between soda lime glass and ZrW{sub 2}O{sub 8} is reduced by increasing particle size of ZrW{sub 2}O{sub 8}. Sintered sample with ZrW{sub 2}O{sub 8} particle size 45-90 {mu}m shows near zero thermal expansion.

Element analysis on Japanese ancient glass by PIXE method

International Nuclear Information System (INIS)

Koizumi, Y.; Kobayashi, K.

2001-01-01

The authors analyzed ancient glasses using PIXE (particle induced X-ray emission) method associated with the accelerator used for the trace analysis of environments and organisms. They examined whether the material properties of the glasses made by ancient technology have correlation with those of each era or each region both in and out of Japan. The alkali lime glasses excavated from Japanese ancient ruins are classified as soda lime glasses and potash lime glasses, and intermediate glasses containing both are also detected. As for the glasses between the late Yayoi period and the early Tumulus period in eastern Japan, glass beads were mostly classified as potash lime glasses. In the mid and late Tumulus periods, soda lime glasses and the glasses with an intermediate composition increased in addition to potash lime glasses. In the analysis of the glass beads excavated from the ruins of the late Yayoi period to the early Tumult period in Tsushima, potash lime glasses and soda lime glasses coexisted in the same period. Most of the coloring components of deep-blue system mostly found in eastern Japan were manganese and iron, and the coloring components such as blue, green, sky blue, etc. were copper. Yellow was the color expressed with lead or lead - iron. The coloring materials were common regardless of the classification of glasses based on main components. (A.O.)

Combined distiller waste utilisation and combustion gases desulphurisation method. The case study of soda-ash industry

Energy Technology Data Exchange (ETDEWEB)

Kasikowski, Tomasz; Buczkowski, Roman; Cichosz, Marcin; Lemanowska, Eliza [Faculty of Chemistry, Nicolas Copernicus University, ul. Gagarina 7, 87-100 Torun (Poland)

2007-09-15

In this paper, a concept of technology that can be helpful for lowering the negative influence of the synthetic (based on the Solvay process) soda ash plant on the natural environment is presented. We describe the desulphurisation of combustion gases from the factory's power plant, which is based on their absorption in the overflow of distiller waste. The excess of lime milk, which is added in the process of ammonia regeneration from filter liquor, results in a strong alkalinity of distiller waste. The high pH of distiller waste favours absorption of acidic combustion gases. The laboratory-scale tests showed about 80% efficiency of the desulphurisation process. The suspension samples we obtained consist mainly of CaCO{sub 3}. We suggest using the obtained solid phase as an adsorbent-insert in Fluidised Bed Combustion technology (FBC). Based on raw material prices, production costs, and average sell prices of the product, economic analysis of innovation was executed. Profits from employing the method presented come mainly from reduction of environmental fees. The sensitivity analysis of cost showed that the application of the desulphurisation process causes cost reduction in soda-ash production accounting for EUR 150 thousand per year (excluding depreciation) in Poland, and EUR 11,700 thousand per year (excluding depreciation) in Sweden. It has been found that the latter value is similar to the positive environmental impact of this innovation expressed in monetary units (EUR 10,350 thousand per year, excluding depreciation). (author)

Evidence for biofilm acid neutralization by baking soda.

Science.gov (United States)

Zero, Domenick T

2017-11-01

The generating of acids from the microbial metabolism of dietary sugars and the subsequent decrease in biofilm pH below the pH at which tooth mineral begins to demineralize (critical pH) are the key elements of the dental caries process. Caries preventive strategies that rapidly neutralize biofilm acids can prevent demineralization and favor remineralization and may help prevent the development of sugar-induced dysbiosis that shifts the biofilm toward increased cariogenic potential. Although the neutralizing ability of sodium bicarbonate (baking soda) has been known for many years, its anticaries potential as an additive to fluoride dentifrice has received only limited investigation. There is evidence that baking soda rapidly can reverse the biofilm pH decrease after a sugar challenge; however, the timing of when it is used in relation to a dietary sugar exposure is critical in that the sooner its used the greater the benefit in preventing a sustained biofilm pH decrease and subsequent demineralization. Furthermore, the effectiveness of baking soda in elevating biofilm pH appears to depend on concentration. Thus, the concentration of baking soda in marketed dentifrice products, which ranges from 10% to 65%, may affect their biofilm pH neutralizing performance. People with hyposalivation particularly may benefit from using fluoride dentifrice containing baking soda because of their diminished ability to clear dietary sugars and buffer biofilm acids. Although promising, there is the need for more evidence that strategies that modify the oral ecology, such as baking soda, can alter the cariogenic (acidogenic and aciduric) properties of biofilm microorganisms. The acid neutralization of dental biofilm by using fluoride dentifrice that contains baking soda has potential for helping counteract modern high-sugar diets by rapidly neutralizing biofilm-generated acid, especially in people with hyposalivation. Copyright © 2017 American Dental Association. Published by

Microbiology of Lonar Lake and other soda lakes

Science.gov (United States)

Paul Antony, Chakkiath; Kumaresan, Deepak; Hunger, Sindy; Drake, Harold L; Murrell, J Colin; Shouche, Yogesh S

2013-01-01

Soda lakes are saline and alkaline ecosystems that are believed to have existed throughout the geological record of Earth. They are widely distributed across the globe, but are highly abundant in terrestrial biomes such as deserts and steppes and in geologically interesting regions such as the East African Rift valley. The unusual geochemistry of these lakes supports the growth of an impressive array of microorganisms that are of ecological and economic importance. Haloalkaliphilic Bacteria and Archaea belonging to all major trophic groups have been described from many soda lakes, including lakes with exceptionally high levels of heavy metals. Lonar Lake is a soda lake that is centered at an unusual meteorite impact structure in the Deccan basalts in India and its key physicochemical and microbiological characteristics are highlighted in this article. The occurrence of diverse functional groups of microbes, such as methanogens, methanotrophs, phototrophs, denitrifiers, sulfur oxidizers, sulfate reducers and syntrophs in soda lakes, suggests that these habitats harbor complex microbial food webs that (a) interconnect various biological cycles via redox coupling and (b) impact on the production and consumption of greenhouse gases. Soda lake microorganisms harbor several biotechnologically relevant enzymes and biomolecules (for example, cellulases, amylases, ectoine) and there is the need to augment bioprospecting efforts in soda lake environments with new integrated approaches. Importantly, some saline and alkaline lake ecosystems around the world need to be protected from anthropogenic pressures that threaten their long-term existence. PMID:23178675

Rootstocks for 'Tahiti' lime

Directory of Open Access Journals (Sweden)

Stenzel Neusa Maria Colauto

2004-01-01

Full Text Available The 'Tahiti' lime (Citrus latifolia Tanaka is an important commercial citrus cultivar in Brazil. 'Rangpur' lime has being used as its main rootstock, but it is susceptible to root rot caused by Phytophthora, reducing tree longevity. An experiment was set up in a randomized block design, with three trees per plot of each rootstock and four replicates, and run for 12 years, aiming to compare the performance of 'IAC-5 Tahiti' lime, budded on 'Rangpur' lime (Citrus limonia Osb.; 'C-13' citrange (Citrus sinensis (L. Osb. × Poncirus trifoliata (L. Raf.; 'African' rough lemon (Citrus jambhiri Lush.; 'Volkamer' lemon (Citrus volkameriana Ten. & Pasq.; trifoliate orange (Poncirus trifoliata (L. Raf.; 'Sunki' mandarin (Citrus sunki Hort. ex Tan. and 'Cleopatra' mandarin (Citrus reshni Hort. ex Tan.. Eleven years after the establishment of the orchard, trees with the greatest canopy development were budded on 'C-13' citrange and 'African' rough lemon, and both differed significantly from trees budded on trifoliate orange, 'Sunki' and 'Cleopatra' mandarins, which presented the smallest canopy development. Trees budded on 'Rangpur' lime and 'C-13' citrange had the highest cumulative yields, and were different from trees budded on trifoliate orange, 'Cleopatra' and 'Sunki' mandarins. There was no rootstock effect on mean fruit weight and on the total soluble solid/acid ratio in the juice. The 'Rangpur' lime and the 'Cleopatra' mandarin rootstocks reduced longevity of plants.

Soda intake and osteoporosis risk in postmenopausal American-Indian women

Science.gov (United States)

Supplee, Joy D; Duncan, Glen E; Bruemmer, Barbara; Goldberg, Jack; Wen, Yang; Henderson, Jeffrey A

2015-01-01

Objective Low bone mass often leads to osteoporosis and increased risk of bone fractures. Soda consumption may contribute to imbalances that lead to decreased bone mineral density (BMD) and general bone health. We examined the relationship between soda consumption and osteoporosis risk in postmenopausal American-Indian women, an at-risk population because of nutritional and other lifestyle-related factors. Design Cross-sectional analysis using logistic regression to examine associations between soda consumption and osteoporosis, and linear regression to examine the association between soda consumption and BMD, with and without adjustment for demographic and lifestyle factors. Quantitative ultrasound of the heel was performed to estimate BMD (g/cm2). Setting American-Indian communities in the Northern Plains and Southwestern USA. Subjects A total of 438 postmenopausal American-Indian women. Results Women with osteoporosis were significantly older and had lower BMI, average daily soda intakes, BMD levels and use of hormones than women without osteoporosis (P 0·05), although age (increased), BMI (decreased) and past hormone use (decreased) were all significantly associated with osteoporosis risk (PIndian women, analyses did confirm confounding between soda consumption and age and BMI. This suggests that any potential effects of soda consumption on bone health are largely mediated through these factors. PMID:21208477

Improved control of sucrose losses and clarified juice turbidity with lime saccharate in hot lime clarification of sugarcane juice and other comparisons with milk of lime

Science.gov (United States)

A comparative investigation of adding milk of lime (MOL) versus lime saccharate (SACCH) in hot lime clarification of juice at a U.S. sugarcane factory was undertaken to quantify performance across the 2009 processing season after a preliminary factory study in 2008. SACCH was prepared by adding hyd...

Mineral Resource of the Month: Lime

Science.gov (United States)

Corathers, Lisa A.

2015-01-01

Lime is the common term for several chemicals in three major categories: quicklime, hydrated lime and refractory dead-burned dolomite. Lime is almost never found naturally. It is primarily manufactured by burning limestone in kilns, followed by hydration when necessary. 

Arsenic removal by lime softening

DEFF Research Database (Denmark)

Kaosol, T.; Suksaroj, C.; Bregnhøj, Henrik

2002-01-01

This paper focuses on the study of arsenic removal for drinking water by lime softening. The initial arsenic (V) concentration was 500 and 1,000 ug/L in synthetic groundwater. The experiments were performed as batch tests with varying lime dosages and mixing time. For the synthetic groundwater......, arsenic (V) removal increased with increasing lime dosage and mixing time, as well as with the resulting pH. The residual arsenic (V) in all cases was lower than the WHO guideline of 10 ug/L at pH higher than 11.5. Kinetic of arsenic (V) removal can be described by a first-order equation as C1 = C0*e......^-k*t. The relation between the constant (k value) and increasing lime dosage was found to be linear, described by k = 0.0034 (Dlime). The results support a theory from the literature that the arsenic (V) was removed by precipitation af Ca3(AsO4)2. The results obtained in the present study suggest that lime...

The relationship between amount of soda consumed and intention to reduce soda consumption among adults exposed to the Choose Health LA 'Sugar Pack' health marketing campaign.

Science.gov (United States)

Robles, Brenda; Blitstein, Jonathan L; Lieberman, Alicea J; Barragan, Noel C; Gase, Lauren N; Kuo, Tony

2015-10-01

To examine behavioural intention to reduce soda consumption after exposure to the Choose Health LA 'Sugar Pack' campaign in Los Angeles County, California, USA. A cross-sectional street-intercept survey was conducted to assess knowledge, attitudes, health behaviours and behavioural intentions after exposure to the 'Sugar Pack' campaign. A multivariable regression analysis was performed to examine the relationships between the amount of soda consumed and self-reported intention to reduce consumption of non-diet soda among adults who saw the campaign. Three pre-selected Los Angeles County Metro bus shelters and/or rail stops with the highest number of 'Sugar Pack' campaign advertisement placements. Riders of the region's Metro buses and railways who were the intended audience of the campaign advertisements. The overall survey response rate was 56 % (resulting n 1041). Almost 60 % of respondents were exposed to the advertisements (619/1041). The multivariable logistic regression analysis suggested that the odds of reporting intention to reduce soda consumption among moderate consumers (1-6 sodas/week) were 1·95 times greater than among heavy consumers (≥1 soda/d), after controlling for clustering and covariates. Respondents with less than a high-school education and who perceived sugary beverage consumption as harmful also had higher odds; in contrast, respondents aged ≥65 years had lower odds. Results suggest that future campaigns should be tailored differently for moderate v. heavy consumers of soda. Similar tailoring strategies are likely needed for younger groups, for those with less educational attainment and for those who do not perceive consumption of soda as harmful.

Enhancement of plaque removal by baking soda toothpastes from less accessible areas in the dentition.

Science.gov (United States)

Thong, S; Hooper, W; Xu, Y; Ghassemi, A; Winston, A

2011-01-01

To determine if baking soda toothpastes are relatively more effective than non-baking soda toothpastes in promoting plaque removal from less accessible sites in the dentition. Several single-brushing comparisons of baking soda and non-baking soda toothpastes for their overall ability to remove plaque have been published. In this study, individual comparisons of these published data, comparing the plaque removal performance of baking soda and non-baking soda toothpastes at various sites in the dentition, were examined to see if there were any site-dependant performance trends. The site-specific single-brushing data were then combined and analyzed in two ways. Meta-analyses of the clinical studies were performed to compare baking soda's relative plaque removal advantage at various sites in the mouth using paired t-testing at p baking soda toothpastes were graphically compared with plaque index reductions due to brushing with non-baking soda dentifrices. The percent relative plaque removal advantage for baking soda toothpastes at various sites were plotted against the reduction in plaque index due to brushing with non-baking soda toothpastes. Individual comparisons showed that brushing with the toothpastes containing baking soda generally removed significantly more plaque from each site than brushing with toothpastes without baking soda. The relative efficacy advantage for baking soda toothpastes was consistently higher at sites where the non-baking soda toothpastes removed less plaque. Meta-analytical comparisons confirmed baking soda toothpastes to be relatively more effective in enhancing plaque removal from sites where less plaque was removed compared to brushing with non-baking soda toothpastes (p baking soda toothpastes' relative plaque removal advantage could be seen to increase hyperbolically with decreasing plaque removal by the non-baking soda toothpastes with which they were compared. We presuppose that the reason less plaque is removed by non-baking soda

Effect of baking soda in dentifrices on plaque removal.

Science.gov (United States)

Myneni, Srinivas R

2017-11-01

The prevention of dental caries and periodontal diseases targets control of dental plaque biofilm. In this context, chemical agents could represent a valuable complement to mechanical plaque control by reducing and controlling biofilm formation. The literature on the effectiveness of different dentifrices has not, however, been carefully categorized. A lack of consensus exists among dental professionals on a recommendation for a universal dentifrice for plaque control. The authors reviewed the scientific data on the different properties of sodium bicarbonate (baking soda)-containing dentifrices and their effectiveness in plaque removal. The results of the literature search show that baking soda-containing dentifrices are ideal candidates to be considered as a universal dentifrice because baking soda is inexpensive, abundant in supply, highly biocompatible, exhibits specific antibacterial properties to oral microorganisms, has low abrasivity, and is effective in plaque biofilm removal. Although some patients may benefit from desensitizing or high fluoride-containing dentifrices, those with routine needs may find using dentifrices containing baking soda and fluoride effective. Baking soda and fluoride dentifrices, therefore, may perhaps be considered as a criterion standard for patients with routine oral hygiene needs. Copyright © 2017 American Dental Association. Published by Elsevier Inc. All rights reserved.

40 CFR 98.190 - Definition of the source category.

Science.gov (United States)

2010-07-01

.... (a) Lime manufacturing plants (LMPs) engage in the manufacture of a lime product (e.g., calcium oxide, high-calcium quicklime, calcium hydroxide, hydrated lime, dolomitic quicklime, dolomitic hydrate, or... kraft pulp mill, soda pulp mill, sulfite pulp mill, or only processes sludge containing calcium...

Low Temperature Soda-Oxygen Pulping of Bagasse

OpenAIRE

Fengxia Yue; Ke-Li Chen; Fachuang Lu

2016-01-01

Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today’s pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum coo...

Earth mortars and earth-lime renders

Directory of Open Access Journals (Sweden)

Maria Fernandes

2008-01-01

Full Text Available Earth surface coatings play a decorative architectural role, apart from their function as wall protection. In Portuguese vernacular architecture, earth mortars were usually applied on stone masonry, while earth renders and plasters were used on indoors surface coatings. Limestone exists only in certain areas of the country and consequently lime was not easily available everywhere, especially on granite and schist regions where stone masonry was a current building technique. In the central west coast of Portugal, the lime slaking procedure entailed slaking the quicklime mixed with earth (sandy soil, in a pit; the resulting mixture would then be combined in a mortar or plaster. This was also the procedure for manufactured adobes stabilized with lime. Adobe buildings with earth-lime renderings and plasters were also traditional in the same region, using lime putty and lime wash for final coat and decoration. Classic decoration on earth architecture from the 18th-19th century was in many countries a consequence of the François Cointeraux (1740-1830 manuals - Les Cahiers d'Architecture Rurale" (1793 - a French guide for earth architecture and building construction. This manual arrived to Portugal in the beginning of XIX century, but was never translated to Portuguese. References about decoration for earth houses were explained on this manual, as well as procedures about earth-lime renders and ornamentation of earth walls; in fact, these procedures are exactly the same as the ones used in adobe buildings in this Portuguese region. The specific purpose of the present paper is to show some cases of earth mortars, renders and plasters on stone buildings in Portugal and to explain the methods of producing earth-lime renders, and also to show some examples of rendering and coating with earth-lime in Portuguese adobe vernacular architecture.

Ectomycorrhizal activity as affected by soil liming

Energy Technology Data Exchange (ETDEWEB)

Andersson, Solbritt

1996-05-01

Acidification of the forest soils in southern Sweden due to atmospheric deposition has become evident during recent decades. To counteract further acidification, liming of forests in the most affected areas has been proposed. Most forest trees in the temperate and boreal forest ecosystems live in symbiosis with ectomycorrhizal fungi, and their uptake of mineral nutrients from the soil is greatly influenced by the symbiosis. In this thesis effects of liming on ectomycorrhiza have been studied in relation to effects on root colonization, fungal growth and nitrogen uptake. In field experiments the effects of liming on ectomycorrhizal colonization of root tips were variable, possibly due to different soil types and climatic variations. However, a changed mycorrhizal community structure could be detected. Laboratory studies also showed that the substrate may influence the outcome of lime applications; the nutrient status of the substrate had a marked effect on how mycelial growth was affected by liming. Under the experimental conditions used in the studies presented in this thesis, liming reduced the uptake of nitrogen and phosphorus by both mycorrhizal and non-mycorrhizal plants. The amount of extractable nitrogen and phosphorus in the peat was also reduced by liming. The latter could be due to either microbial or chemical immobilization. The lime induced decrease in nitrogen uptake was stronger in non-mycorrhizal plants than in mycorrhizal plants. Thus, the mycorrhizal plants had a higher ability to deal with the negative effects of liming on nitrogen availability. This was not the case for phosphorus. The lime induced decrease in phosphorus uptake was stronger for mycorrhizal plants, and in the highest lime treatment there was no significant difference between the mycorrhizal and the non-mycorrhizal spruce plants. 76 refs, 2 figs, 1 tab

Interfacial Properties of CZTS Thin Film Solar Cell

Directory of Open Access Journals (Sweden)

N. Muhunthan

2014-01-01

Full Text Available Cu-deficient CZTS (copper zinc tin sulfide thin films were grown on soda lime as well as molybdenum coated soda lime glass by reactive cosputtering. Polycrystalline CZTS film with kesterite structure was produced by annealing it at 500°C in Ar atmosphere. These films were characterized for compositional, structural, surface morphological, optical, and transport properties using energy dispersive X-ray analysis, glancing incidence X-ray diffraction, Raman spectroscopy, scanning electron microscopy, atomic force microscopy, UV-Vis spectroscopy, and Hall effect measurement. A CZTS solar cell device having conversion efficiency of ~0.11% has been made by depositing CdS, ZnO, ITO, and Al layers over the CZTS thin film deposited on Mo coated soda lime glass. The series resistance of the device was very high. The interfacial properties of device were characterized by cross-sectional SEM and cross-sectional HRTEM.

Low Temperature Soda-Oxygen Pulping of Bagasse.

Science.gov (United States)

Yue, Fengxia; Chen, Ke-Li; Lu, Fachuang

2016-01-13

Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today's pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum cooking temperature 100 °C, time hold at maximum temperature 180 min, initial pressure of oxygen 0.6 MPa, MgSO4 charge 0.5%, and de-pithed bagasse consistency 12%. Properties of the resultant pulp were screened yield 60.9%, Kappa number 14, viscosity 766 dm³/kg, and brightness 63.7% ISO. Similar pulps were also obtained at 110 °C or 105 °C with a cooking time of 90 min. Compared with pulps obtained at higher temperatures (115-125 °C), this pulp had higher screened yield, brightness, and acceptable viscosity, while the delignification degree was moderate. These results indicated that soda-oxygen pulping at 100 °C, the lowest cooking temperature reported so far for soda-oxygen pulping, is a suitable process for making chemical pulp from bagasse. Pulping at lower temperature and using oxygen make it an environmental friendly and energy-saving pulping process.

Low Temperature Soda-Oxygen Pulping of Bagasse

Directory of Open Access Journals (Sweden)

Fengxia Yue

2016-01-01

Full Text Available Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today’s pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum cooking temperature 100 °C, time hold at maximum temperature 180 min, initial pressure of oxygen 0.6 MPa, MgSO4 charge 0.5%, and de-pithed bagasse consistency 12%. Properties of the resultant pulp were screened yield 60.9%, Kappa number 14, viscosity 766 dm3/kg, and brightness 63.7% ISO. Similar pulps were also obtained at 110 °C or 105 °C with a cooking time of 90 min. Compared with pulps obtained at higher temperatures (115–125 °C, this pulp had higher screened yield, brightness, and acceptable viscosity, while the delignification degree was moderate. These results indicated that soda-oxygen pulping at 100 °C, the lowest cooking temperature reported so far for soda-oxygen pulping, is a suitable process for making chemical pulp from bagasse. Pulping at lower temperature and using oxygen make it an environmental friendly and energy-saving pulping process.

Can soda fountains be recommended in hospitals?

Science.gov (United States)

Chaberny, Iris F; Kaiser, Peter; Sonntag, Hans-Günther

2006-09-01

Mineral water (soda water) is very popular in Germany. Therefore, soda fountains were developed as alternatives to the traditional deposit bottle system. Nowadays, different systems of these devices are commercially available. For several years, soda fountains produced by different companies have been examined at the University Hospital of Heidelberg. In 1998, it was possible for the first time to observe and evaluate one of these systems over a period of 320 days in a series of microbiological examinations. The evaluation was implemented on the basis of the German drinking water regulation (Anonymous, 1990. Gesetz über Trinkwasser und Wasser für Lebensmittelbetriebe (Trinkwasserverordnung - TrinkwV) vom 12. Dezember 1990. Bundesgesetzblatt 66, 2613ff). Initially, the bacteria counts exceeded the reference values imposed by the German drinking water regulation in almost 50% of the analyses. Pseudomonas aeruginosa was also detected in almost 38% of the samples. After a re-arrangement of the disinfection procedure and the removal of the charcoal filter, Pseudomonas aeruginosa was not detectable any more. However, the bacteria counts still frequently exceeded the reference values of the German drinking water regulation. Following our long-term analysis, we would not recommend soda fountains in high-risk areas of hospitals. If these devices are to be used in hospitals, the disinfection procedures should be executed in weekly or fortnightly intervals and the water quality should be examined periodically.

Carbon dioxide: making the right connection

African Journals Online (AJOL)

This highlights safety issues concerning pipeline provision of carbon dioxide, and that it is of utmost ... capnograph sample line, gas analysis unit, water trap and soda .... The heat generated by the chemical reaction between soda lime.

The Stabilization of Weathered Dolerite Aggregates with Cement, Lime, and Lime Fly Ash for Pavement Construction

Directory of Open Access Journals (Sweden)

Felix N. Okonta

2014-01-01

Full Text Available An experimental program was performed on weathered dolerite specimens stabilized by adding varying percentages of cement (4, 8, 12, and 16 % and lime (6 and 12 % and a combination of lime and fly ash (6% lime + 12% Fly ash and 12% lime + 12% Fly ash % by dry weight of soil. The strength was examined under three different curing methods, namely, membrane curing (MBC, alternate moist-air curing (MAC, and water curing (WAC, by conducting unconfined compressive strength (UCS tests. Simple polynomial and linear functions (regression models were used to define the relationships between the variables investigated. Membrane curing (MBC gave results close enough to the water curing (WAC to indicate that it can be confidently used on the field during pavement construction. From the results obtained, for class B (interurban collector and major rural roads pavement construction, addition of 8% cement was recommended for road base construction with stabilized WDA. Also the addition of 12 + 12% Lime and Fly Ash was recommended for road subbase construction with stabilized WDA. Stabilized WDA against the prejudiced myths would perform satisfactorily for base and subbase construction in both heavily trafficked and low volume roads with economic quantities of cement, lime, and fly ash in South Africa.

Recycled sand in lime-based mortars.

Science.gov (United States)

Stefanidou, M; Anastasiou, E; Georgiadis Filikas, K

2014-12-01

The increasing awareness of the society about safe guarding heritage buildings and at the same time protecting the environment promotes strategies of combining principles of restoration with environmentally friendly materials and techniques. Along these lines, an experimental program was carried out in order to investigate the possibility of producing repair, lime-based mortars used in historic buildings incorporating secondary materials. The alternative material tested was recycled fine aggregates originating from mixed construction and demolition waste. Extensive tests on the raw materials have been performed and mortar mixtures were produced using different binding systems with natural, standard and recycled sand in order to compare their mechanical, physical and microstructure properties. The study reveals the improved behavior of lime mortars, even at early ages, due to the reaction of lime with the Al and Si constituents of the fine recycled sand. The role of the recycled sand was more beneficial in lime mortars rather than the lime-pozzolan or lime-pozzolan-cement mortars as a decrease in their performance was recorded in the latter cases due to the mortars' structure. Copyright © 2014 Elsevier Ltd. All rights reserved.

GPU-powered model analysis with PySB/cupSODA.

Science.gov (United States)

Harris, Leonard A; Nobile, Marco S; Pino, James C; Lubbock, Alexander L R; Besozzi, Daniela; Mauri, Giancarlo; Cazzaniga, Paolo; Lopez, Carlos F

2017-11-01

A major barrier to the practical utilization of large, complex models of biochemical systems is the lack of open-source computational tools to evaluate model behaviors over high-dimensional parameter spaces. This is due to the high computational expense of performing thousands to millions of model simulations required for statistical analysis. To address this need, we have implemented a user-friendly interface between cupSODA, a GPU-powered kinetic simulator, and PySB, a Python-based modeling and simulation framework. For three example models of varying size, we show that for large numbers of simulations PySB/cupSODA achieves order-of-magnitude speedups relative to a CPU-based ordinary differential equation integrator. The PySB/cupSODA interface has been integrated into the PySB modeling framework (version 1.4.0), which can be installed from the Python Package Index (PyPI) using a Python package manager such as pip. cupSODA source code and precompiled binaries (Linux, Mac OS/X, Windows) are available at github.com/aresio/cupSODA (requires an Nvidia GPU; developer.nvidia.com/cuda-gpus). Additional information about PySB is available at pysb.org. paolo.cazzaniga@unibg.it or c.lopez@vanderbilt.edu. Supplementary data are available at Bioinformatics online. © The Author(s) 2017. Published by Oxford University Press.

SODA: The reduced database for the TdeV tokamak

International Nuclear Information System (INIS)

Cote, A.; Michaud, D.; Caumartin, J.; de Villers, P.; Gauthier, Y.; Gauvreau, J.; Larsen, J.

1997-01-01

SODA which stands for Systgrave eme d close-quote Organisation des Donnacute ees et d close-quote Analyse, is a general database for TdeV. SODA has the following goals: to produce a database of a reduced set of physical data; to ensure that these data are validated; to record all the parameters relevant to tokamak operation and experiments; to facilitate the retrieval of data using given selection criteria; and to improve data accessibility and analysis. The relational database ORACLE trademark has been chosen to provide flexibility and to accommodate the increasing expectations of the TdeV researchers. In-house expertise allows custom-made tables and centralized data management. In the process of creating SODA several new interfaces for the scientific coordinator, machine operator, and diagnosticians have been added to provide a better definition of the experiment for the archiving system. The database includes the more relevant machine and diagnostic parameters, plasma perturbations (rf, biasing, gas hor-ellipsis), mean and standard deviation of physical signals, plasma profiles, and code results (equilibrium hor-ellipsis) for selected time windows in a discharge. Users of the X-window interface of SODA are not required to know the database structure or the SQL language. SODA has been operating successfully for over a year and its capabilities are continuously expanding. copyright 1997 American Institute of Physics

Comparative evaluation of aerial lime mortars for architectural conservation

OpenAIRE

Faria, Paulina; Henriques, Fernando M.A.; Rato, Vasco

2008-01-01

Journal of Cultural Heritage 9 (2008) 338-346 International bibliography on conservation usually refers that mortars made with lime putty with long extinction periods behave better than others made with the current dry hydrated limes. In order to evaluate this assess, an experimental study of lime mortars was carried out, using dry hydrated lime and two lime putties. It becomes clear that the use of lime putties with long extinction periods in mortars allow better performances, pa...

College Cafeteria Signage Increases Water Intake but Water Position on the Soda Dispenser Encourages More Soda Consumption.

Science.gov (United States)

Montuclard, Astrid Linn; Park-Mroch, Jennifer; O'Shea, Amy M J; Wansink, Brian; Irvin, Jill; Laroche, Helena H

2017-10-01

To evaluate the effects of improved water location visibility and water dispenser position on the soda dispenser on undergraduate students' beverage choices. Two focus groups with pilot intervention surveys before and after, adding a small sign above the soda dispensers' water button for 6 weeks in a large US university's all-you-can-eat, prepaid dining hall (measured with chi-square tests and logistic and ordinal logistic regression). Focus groups included 15 students. Survey participants included 357 students before and 301 after the intervention. After the intervention, more students reported ever having drunk water with the meal (66.4% to 77.0%; P = .003) and water consumption frequency increased (P = .005). Postintervention, the odds of drinking water increased by 1.57. Preference for other drinks was the main reason for not drinking water. A total of 59% of students had ever changed their preference from water to soda. The clear indication of the water's location increased students' reported water consumption. Further investigation is needed into how a non-independent water dispenser influences students' beverage choice. Clearly labeled, independent water dispensers are recommended. Copyright © 2017 Society for Nutrition Education and Behavior. All rights reserved.

Are energy Drinks Scapegoats? Decomposing Teenagers' Caffeine intake from Energy Drinks and Soda Beverages.

Science.gov (United States)

Turel, Ofir

2018-02-22

Energy drinks have been repeatedly blamed for contributing to caffeine intake among teenagers. This study aimed to estimate and compare the caffeine intake of US teenagers from soda drinks versus energy drinks and shots. Data were taken from a 2015 nationally representative survey (Monitoring the Future) of 8th and 10th graders in the US (47.2% 8th grade; 51.1% female). Participants reported their numbers of consumed sodas, diet sodas, energy drinks, and energy shots per day. These were converted into mg caffeine/day and were contrasted with common guidelines for healthy caffeine intake, stratified by age group and sex. Error-bar charts, ANOVA and ROC curves were used for contrasting caffeine intake from soda drinks and energy drinks, as well as their contribution to exceeding recommended caffeine intake cutoffs. First, in both sexes and grades the intake from soda drinks was significantly higher than the intake from energy drinks. The soda and energy drink intake for males was higher than the intake for females; intake for 8th graders was higher than this of 10th graders. Second, caffeine intake from soda drinks was significantly higher even in those who exceeded the recommended maximum caffeine intake. Third, caffeine intakes from soda and energy drinks were efficacious in explaining the exceeding of the recommended threshold for daily caffeine intake, but the explanatory power of soda drinks was larger. From a caffeine consumption standpoint, health professionals should emphasize reduction in both soda and energy drinks.

A comparative study of the effect of diet and soda carbonated drinks ...

African Journals Online (AJOL)

A comparative study of the effect of diet and soda carbonated drinks on the histology of the cerebellum of adult female albino Wistar rats. ... African Health Sciences ... Group B was administered 50 ml of regular soda (RS), and group C was administered 50 ml of diet soda (DS) each per day for 21 days, and the rats were ...

Durability of air lime mortar

DEFF Research Database (Denmark)

Nielsen, Anders

2016-01-01

This contribution deals with the physical and chemical reasons why pure air lime mortars used in masonry of burned bricks exposed to outdoor climate have shown to be durable from the Middle Ages to our days. This sounds strange in modern times where pure air lime mortars are regarded as weak...... materials, which are omitted from standards for new masonry buildings, where use of hydraulic binders is prescribed. The reasons for the durability seam to be two: 1. The old mortars have high lime contents. 2. The carbonation process creates a pore structure with a fine pored outer layer and coarser pores...

Modification of Lime Mortars with Synthesized Aluminosilicates

Science.gov (United States)

Loganina, Valentina I.; Sadovnikova, Marija E.; Jezierski, Walery; Małaszkiewicz, Dorota

2017-10-01

The increasing attention for restoration of buildings of historical and architectural importance has increased the interest for lime-based binders, which could be applied for manufacturing repair mortars and plasters compatible with historical heritage. Different additives, admixtures or fibers may be incorporated to improve mechanical and thermal features of such materials. In this study synthesized aluminosilicates (SA) were applied as an additive for lime mortar. The technology of synthesis consisted in the deposition of aluminosilicates from a sodium liquid glass by the aluminum sulphate Al2(SO4)3. The goal of this investigation was developing a new method of aluminosilicates synthesis from a sodium liquid glass and using this new material as a component for a lime mortar. Aluminosilicates were precipitated from the solution of aluminum sulphate Al2(SO)3 and sodium silicate. SA were then used as an additive to calcareous compositions and their influence was tested. Mortars were prepared with commercial air lime and siliceous river sand. Air lime binder was replaced by 5 and 10 wt.% of SA. Calcareous composition specimens were formed at water/lime ratio 1.0. The following analyses were made: grain size distribution of SA, X-ray diffraction analysis (XRD), sorption properties, plastic strength and compressive strength of lime mortars. XRD pattern of the SA shows the presence of thenardite, gibbsite and amorphous phase represented by aggregate of nano-size cristobalite-like crystallites. Application of SA leads to increase of compressive strength after 90 days of hardening by 28% and 53% at SA content 5 and 10% respectively comparing to specimens without this additive. Contents of chemically bound lime in the reference specimens after 28 days of hardening in air-dry conditions was 46.5%, while in specimens modified with SA contained 50.0-55.3% of bound lime depending on filtrate pH. This testifies to high activity of calcareous composition. The new blended lime

27 CFR 9.27 - Lime Kiln Valley.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Lime Kiln Valley. 9.27... OF THE TREASURY LIQUORS AMERICAN VITICULTURAL AREAS Approved American Viticultural Areas § 9.27 Lime Kiln Valley. (a) Name. The name of the viticultural area described in this section is “Lime Kiln Valley...

Tailings treatment techniques for uranium mill waste: a review of existing information

International Nuclear Information System (INIS)

Sherwood, D.R.; Serne, R.J.

1983-07-01

Of primary concern at uranium mill sites in the United States is the potential of ground-water contamination from mill wastes that are disposed in tailings impoundments. Although many systems have been used to control seepage from tailings impoundments, most of these systems are limited in their ability to handle an excess of tailings solution. Three general amelioration methods were identified: neutralization, fixation and specific constituent removal. During neutralization, a reagent is added to the tailings solution to neutralize the acidity and raise the pH to reduce the solubility of various pH sensitive contaminants. Fixation processes add materials such as lime, cement or asphalt to the waste to produce a physically stable composition that resists leaching of hazardous constituents. Specific constituent removal encompasses varying techniques, such as alternate ore leaching processes, effluent treatment with sorption, or ion exchange agents or selected precipitation that reduce specific constituent concentrations in tailings solution. Neutralization processes appear to be best suited for treating uranium mill tailings because they can, at a reasonable cost, limit the solution concentration of many contaminants. The effectiveness of the process depends on the reagent used as well as the waste being treated. Of the six reagents studied (lime, limestone, caustic soda, soda ash, combined limestone/lime and combined alumina/lime/soda), a combined treatment of limestone and lime seems best, especially for tailings containing ferric iron as the limestone economically buffers the solution acidity while the lime takes the pH to 8.0, an optimum level for heavy metal removal. For those tailings containing ferrous iron, lime alone works best. The costs for the lime/limestone or lime processes range from $0.20 to $1.00 per 1000 gal of treated water, excluding capital equipment costs

Baking soda dentifrice and periodontal health: A review of the literature.

Science.gov (United States)

Sabharwal, Amarpreet; Scannapieco, Frank A

2017-11-01

Mechanical disruption of dental biofilm is critical to maintain periodontal health. Baking soda-containing dentifrices have shown to be potential aids for improving gingival health and maintaining dental biofilm control. Evidence from classic and contemporary literature is reviewed and summarized in this review. In vitro and in vivo (animal and human, respectively) studies and clinical trials have been analyzed. Some clinical studies demonstrated the benefits of baking soda dentifrices in plaque and gingivitis reduction. Clinical trials with longer follow-up would be useful to confirm the impact of baking soda on gingival health. Regular dental biofilm control and adjunctive use of baking soda dentifrices in an otherwise healthy and compliant patient may provide success in maintenance of gingival health. Copyright © 2017 American Dental Association. Published by Elsevier Inc. All rights reserved.

Wetland vegetation responses to liming an Adirondack watershed

Energy Technology Data Exchange (ETDEWEB)

Mackun, I.R.

1993-01-01

Watershed liming as a long-term mitigation strategy to neutralize lake acidity, from increasing acid deposition, was initiated in North America at Woods Lake in the west central Adirondack region of New York. In October 1989, a dose of 10 MT lime (83.5% CaCO[sub 3]) ha[sup [minus]1] was aerially applied to 48% of the watershed. The wetlands adjacent to Woods Lake showed two distinct community types: one dominated by Chamaedaphne calyculata, and one dominated by graminoids and other herbaceous species. Within two years, liming did not alter the structure of either community type, and changed the cover or frequency of only 6 of 64 individual taxa. Most of these changes occurred in the herbaceous community type. The only strong positive response to liming was a nearly threefold increase in cover of the rhizomatous sedge Cladium mariscoides. The cover of Carex interior and Sphagnum spp. benefited from lime addition, while cover of Drosera intermedia and Muhlenbergia uniflora, and frequency of Hypericum canadense responded negatively to lime. Liming influenced the competitive release of only three taxa, all forbs with small growth forms. The tissue chemistry of foliage and twigs of Myrica gale, Chamaedaphne calyculata, and Carex stricta in the Chamaedaphne calyculata community type clearly illustrated species-specific patterns of nutrient accumulation and allocation both before and after liming. Concentrations of 17 of 20 elements responded to liming, although the responses varied among species and plant parts. Carex foliage was least responsive to liming, and Chamaedaphne twigs were most responsive. Elemental changes in plant tissues will be reflected in litter and many influence long-term nutrient dynamics in the wetland community.

Phytochemical fingerprints of lime honey collected in serbia.

Science.gov (United States)

Gašić, Uroš; Šikoparija, Branko; Tosti, Tomislav; Trifković, Jelena; Milojković-Opsenica, Dušanka; Natić, Maja; Tešić, Živoslav

2014-01-01

Composition of phenolic compounds and the sugar content were determined as the basis for characterization of lime honey from Serbia. Particular attention was given to differences in phytochemical profiles of ripe and unripe lime honey and lime tree nectar. Melissopalynological analysis confirmed domination of Tilia nectar in all analyzed samples. Phenolic acids, abscisic acid, flavonoids, and flavonoid glycosides were determined by means of ultra-HPLC coupled with a hybrid mass spectrometer (UHPLC-OrbiTrap). Sugar content was determined using high-performance anion-exchange chromatography with amperometric detection. Similar phenolic compounds characterized unripe and ripe honeys, while the lime tree nectar profile showed notable differences. Compared to lime tree nectar, a high amount of chrysin, pinocembrin, and galangin were detected in both ripe and unripe lime honey. Fructose and glucose were the major constituents of all investigated samples, and amounts were within the limits established by European Union legislation. Sucrose content in the nectar sample was up to two-fold higher when compared to all honey samples. Isomaltose and gentiobiose with turanose content were different in analyzed production stages of lime honey.

Study of the creep of lime-stabilised zirconia

International Nuclear Information System (INIS)

Saint-Jacques, Robert G.

1971-09-01

This research thesis reports the study of creep of stabilised zirconia containing between 13 and 20 per cent of lime, at temperatures between 1.200 and 1.400 C, and under compression stresses between 500 and 4.000 pounds by square inch. Specimens are polycrystalline with an average grain diameter between 7 and 29 microns. The author notably shows that the creep rate of lime-stabilised zirconia is directly proportional to the applied stress, and that the creep apparent activation energy is close to activation energy of volume self-diffusion of calcium and zirconium in lime-stabilised zirconia. Results of creep tests show that, in the studied conditions, the creep rate is directly proportional to the inverse of the grain average diameter, and this is in compliance with the Gifkins and Snowden theory of creep by sliding at grain boundaries. The author also shows that the creep rate of the lime stabilised zirconia varies with lime content, and reaches a maximum when zirconia contains about 15 per cent of lime. Lower creep rates obtained for higher and lower lime contents are explained [fr

Energy efficiency opportunity guide in the lime industry

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The lime industry processes limestone, an abundant inorganic mineral, for metallurgical, industrial and chemical, environmental, and construction applications. The energy the industry uses results in greenhouse gas emissions and the Canadian Lime Institute, in collaboration with Natural Resources Canada, sponsored the development of this guidebook which is intended to provide ideas for saving energy in the lime industry. This document is a practical source of information and can be used to develop self-audit and evaluation techniques to monitor energy usage. The report first provides an overview of the lime industry, then presents its energy costs. General energy efficiency methodologies are highlighted and, in conclusion, advice on improving energy efficiency in general and specifically for lime industry operations is given. This guidebook provides useful information for lime industry operators who are trying to improve the energy efficiency of their operations.

Stain removal and whitening by baking soda dentifrice: A review of literature.

Science.gov (United States)

Li, Yiming

2017-11-01

Tooth discoloration may be caused by intrinsic or extrinsic stains or a combination of both. There are 2 major approaches to removing the stains, including the chemical mechanism using peroxides for tooth bleaching and the mechanical mechanism using abrasives in prophylactic pastes and dentifrices to remove stains, resulting in a whitening effect. Attempts have also been made to add a low concentration of peroxides to dentifrices to enhance their abrasive cleaning to remove tooth stains. This article provides a review of both in vitro and clinical studies on stain removal and whitening effect of dentifrices containing sodium bicarbonate (baking soda). In recent years, whitening dentifrices have become popular because of little additional effort for use, ease of availability, low cost, and accumulated evidence of clinical efficacy and safety in the literature. Advances in research and technology have led to innovative formulations of dentifrices using baking soda as the sole abrasive or a component of an abrasive system. Baking soda is biologically compatible with acid-buffering capacities, antibacterial at high concentrations, and has a relatively lower abrasivity. The evidence available in the literature indicates that baking soda-based dentifrices are effective and safe for tooth stain removal and consequently whitening. A number of clinical studies have also shown that baking soda-based dentifrices are more effective in stain removal and whitening than some non-baking soda-containing dentifrices with a higher abrasivity. So far, research efforts have mainly focused on stain removal and tooth-whitening efficacy and clinical safety of baking soda dentifrices used with manual toothbrushes, with only a few studies investigating their effects using powered toothbrushes, for which further research is encouraged. As part of a daily oral hygiene practice, baking soda-based dentifrice is a desirable, alternative or additional measure for tooth stain removal and whitening

Gluten-Free Recipes

Science.gov (United States)

... Tofu and Shrimp Curry Irish Soda Bread Jalapeño Poppers Key Lime Pie Key Lime Pie Shooters Knorr’s ... Dill Dip Gruyere Crustinis Hot Chili Dip Jalapeño Poppers Knorr’s Vegetable Dip Lemon Dipping Sauce Meatballs for ...

Microbial Flocculant for Nature Soda

Energy Technology Data Exchange (ETDEWEB)

Qin, Peiyong; Zhang, Tong; Chen, Cuixian

2004-03-31

Microbial flocculant for nature soda has been studied. Lactobacillus TRJ21, which was able to produce an excellent biopolymer flocculant for nature soda, was obtained in our lab. The microbial flocculant was mainly produced when the bacteria laid in stationary growth phase. Fructose or glucose, as carbon sources, were more favorable for the bacterial growth and flocculant production. The bacteria was able to use ammonium sulfate or Urea as nitrogen to produce flocculant, but was not able to use peptone effectively. High C/N ratio was more favorable to Lactobacillus TRJ21 growth and flocculant production than low C/N ratio. The biopolymer flocculant was mainly composed of polysaccharide and protein with a molecular weight 1.38x106 by gel permeation chromatography. It was able to be easily purified from the culture medium by acetone. Protein in the flocculant was tested for the flocculating activity ingredient by heating the flocculant.

Regular-soda intake independent of weight status is associated with asthma among US high school students.

Science.gov (United States)

Park, Sohyun; Blanck, Heidi M; Sherry, Bettylou; Jones, Sherry Everett; Pan, Liping

2013-01-01

Limited research shows an inconclusive association between soda intake and asthma, potentially attributable to certain preservatives in sodas. This cross-sectional study examined the association between regular (nondiet)-soda intake and current asthma among a nationally representative sample of high school students. Analysis was based on the 2009 national Youth Risk Behavior Survey and included 15,960 students (grades 9 through 12) with data for both regular-soda intake and current asthma status. The outcome measure was current asthma (ie, told by doctor/nurse that they had asthma and still have asthma). The main exposure variable was regular-soda intake (ie, drank a can/bottle/glass of soda during the 7 days before the survey). Multivariable logistic regression was used to estimate the adjusted odds ratios for regular-soda intake with current asthma after controlling for age, sex, race/ethnicity, weight status, and current cigarette use. Overall, 10.8% of students had current asthma. In addition, 9.7% of students who did not drink regular soda had current asthma, and 14.7% of students who drank regular soda three or more times per day had current asthma. Compared with those who did not drink regular soda, odds of having current asthma were higher among students who drank regular soda two times per day (adjusted odds ratio=1.28; 95% CI 1.02 to 1.62) and three or more times per day (adjusted odds ratio=1.64; 95% CI 1.25 to 2.16). The association between high regular-soda intake and current asthma suggests efforts to reduce regular-soda intake among youth might have benefits beyond improving diet quality. However, this association needs additional research, such as a longitudinal examination. Published by Elsevier Inc.

Stress relaxation in tempered glass caused by heat soak testing

DEFF Research Database (Denmark)

Schneider, Jens; Hilcken, Jonas; Aronen, Antti

2016-01-01

Heat soak testing of tempered glass is a thermal process required after the tempering process itself to bring glasses of commercial soda-lime-silica-glass to failure that are contaminated with nickel sulphide inclusions, diameter 50 mm to 500 mm typically. Thus, the tests avoid a so-called "spont...... of commercial soda-lime-silica glass, it causes stress relaxation in tempered glass and the fracture pattern of the glass changes accordingly, especially thin glasses are affected. Based on the Tool-Narayanaswamy-Model, this paper comprises the theoretical background of the stress...

Quantitative bacterial examination and chemical evaluation of Diet, Club, and Ice-cream Sodas, Soft Drinks

International Nuclear Information System (INIS)

Watoo, M.K.S.; Watoo, F.S.; Kazi, T.G.; Tirmizi, S.A.; Iqbal, J.

2005-01-01

Diet, club, and ice cream sodas are flavored soft drinks consumed throughout the world, especially in summer seasons. This study has been undertaken to monitor the bacterial and chemical contamination of these national and international branded drinks procured from local markets. The isolated coliforms and microbes were E. coli Salmonella spp, Klebsiella spp, Enterobacter spp, Shigella spp, and Bacillus cereus. Diet and club sodas were less contaminated with microorganisms than were ice-cream sodas. Fifteen trace and toxic elements were identified with an atomic absorption spectrophotometer following the improved ash digestion method. The values of Nickel (Ni), (0.15 mg/L), (Pb) (0.28mg/L), Cadmium (Cd) (0.13mg/L) and Aluminum (Al) (0.76 mg/L) were higher than the (WHO) recommended limits. The concentrations of (Na, Fe, Pb) and Chromium (Cr) were higher in club sodas than diet and ice-cream sodas and the concentrations of Calcium (Ca), (Mn) in ice-cream sodas were also higher than diet and club sodas. Overall, the ice-cream sodas did not conform to the (WHO) standards allowed for safe ingestion of micro- and macro-metals in various drinks. (author)

Enhancement of plaque removal efficacy by tooth brushing with baking soda dentifrices: results of five clinical studies.

Science.gov (United States)

Putt, Mark S; Milleman, Kimberly R; Ghassemi, Annahita; Vorwerk, Linda M; Hooper, William J; Soparkar, Pramod M; Winston, Anthony E; Proskin, Howard M

2008-01-01

An earlier clinical study demonstrated that brushing with a commercial Arm & Hammer dentifrice containing baking soda physically removed significantly more plaque than brushing with either of two commercial dentifrices which did not contain baking soda. However, little has been done to confirm these results and to compare baking soda-containing dentifrices with more recently commercialized non-baking soda dentifrice formulations. The objective of this study was to compare commercial dentifrices containing 20% to 65% baking soda and commercial dentifrices without baking soda in enhancing plaque removal efficacy of tooth brushing. Five randomized, controlled, blinded, crossover clinical studies were performed among healthy adult volunteers who provided informed consent. After approximately 24 hours without oral hygiene, subjects with sufficient plaque were enrolled in the study phase. Plaque was scored before and after supervised brushing for one minute using the Turesky, et al. modification of the Quigley-Hein Plaque Index at six sites per tooth according to Soparkar's modification as described by Lobene, et al. In each study, wash-out periods with a regular dentifrice not evaluated in the study separated each product treatment. In all studies, every dentifrice exhibited a significant (p baking soda dentifrices resulted in statistically greater (p baking soda. Results on other tooth surfaces, such as facial, lingual, proximal, and gingival surfaces also demonstrated statistically greater (p baking soda-containing dentifrices as compared to the baking soda-free dentifrices. In three of the studies comparing different levels of baking soda, brushing with dentifrices with higher concentrations of baking soda consistently removed numerically more plaque than those containing lower levels. In one of these three studies, the difference in plaque removal between the baking soda dentifrices reached statistical significance. The results suggest a positive relationship

The Untapped Power of Soda Taxes: Incentivizing Consumers, Generating Revenue, and Altering Corporate Behavior

Directory of Open Access Journals (Sweden)

Sarah A. Roache

2017-09-01

Full Text Available Globally, soda taxes are gaining momentum as powerful interventions to discourage sugar consumption and thereby reduce the growing burden of obesity and non-communicable diseases (NCDs. Evidence from early adopters including Mexico and Berkeley, California, confirms that soda taxes can disincentivize consumption through price increases and raise revenue to support government programs. The United Kingdom’s new graduated levy on sweetened beverages is yielding yet another powerful impact: soda manufacturers are reformulating their beverages to significantly reduce the sugar content. Product reformulation – whether incentivized or mandatory – helps reduce overconsumption of sugars at the societal level, moving away from the long-standing notion of individual responsibility in favor of collective strategies to promote health. But as a matter of health equity, soda product reformulation should occur globally, especially in low- and middleincome countries (LMICs, which are increasingly targeted as emerging markets for soda and junk food and are disproportionately impacted by NCDs. As global momentum for sugar reduction increases, governments and public health advocates should harness the power of soda taxes to tackle the economic, social, and informational drivers of soda consumption, driving improvements in food environments and the public’s health.

Stream capture to form Red Pass, northern Soda Mountains, California

Science.gov (United States)

Miller, David; Mahan, Shannon

2014-01-01

Red Pass, a narrow cut through the Soda Mountains important for prehistoric and early historic travelers, is quite young geologically. Its history of downcutting to capture streams west of the Soda Mountains, thereby draining much of eastern Fort Irwin, is told by the contrast in alluvial fan sediments on either side of the pass. Old alluvial fan deposits (>500 ka) were shed westward off an intact ridge of the Soda Mountains but by middle Pleistocene time, intermediate-age alluvial fan deposits (~100 ka) were laid down by streams flowing east through the pass into Silurian Valley. The pass was probably formed by stream capture driven by high levels of groundwater on the west side. This is evidenced by widespread wetland deposits west of the Soda Mountains. Sapping and spring discharge into Silurian Valley over millennia formed a low divide in the mountains that eventually was overtopped and incised by a stream. Lessons include the importance of groundwater levels for stream capture and the relatively youthful appearance of this ~100-200 ka feature in the slowly changing Mojave Desert landscape.

Como evitar a formação de substâncias tóxicas durante a absorção de dióxido de carbono pela cal sodada com uso de anestésicos halogenados Como evitar la formación de substancias tóxicas durante la absorción de dióxido de carbono por la cal sodada con uso de anestésicos halogenados Preventing toxic substances production during carbon dioxide absorption by soda lime with halogenate anesthetics

Directory of Open Access Journals (Sweden)

Renato Ângelo Saraiva

2004-06-01

para evitar excesivo aumento de la temperatura y grande degradación metabólica de los halogenados sin perjudicar la absorción del dióxido de carbono. CONCLUSIONES: Se debe tener el cuidado en usar la cal sodada lo antes posible y cuando ella queda expuesta al medio ambiente (aire seco por muchas horas como por ejemplo en un final de semana (mas de 48 horas es recomendable colocar agua, de preferencia destilada, en la relación de 25 ml para cada 500 g de cal. Actualmente la industria está bien informada sobre el problema de la composición de la cal, entonces, se debe preferir la cal sodada que tenga solamente el hidróxido de calcio y sea totalmente desprovista de hidróxido de potasio e hidróxido de sodio.BACKGROUND AND OBJECTIVES: Since the beginning, soda lime use has presented some complications which resulted in its difficult application. However major advantages such as decreasing fresh gas flow, anesthetic consumption and operating room pollution, and improving breathing system and airway humidity, have pushed research forward to improve it and assure the continuity of its use. Currently, there are problems with dehydration, increased temperature and metabolic degradation of halogenate agents, which require special care to prevent toxic substances formation. CONTENTS: There is a chain reaction as from dehydrated or dried out soda lime with very low percent volume of water. There is increased temperature, more halogenate anesthetic absorption by lime granules, followed by higher metabolic degradation of these agents' molecules and, as a consequence, the production of toxic substances, such as Compound A by reaction of hydroxides with sevoflurane. There is also carbon monoxide production by reaction of halogenate anesthetics and strong lime bases. Compound A is nephrotoxic and carbon monoxide may lead to hypoxia and severe coagulation problems. In addition to care with soda lime hydration it is possible to use it without strong bases, such as potassium and

Engineering Properties of Bentonite Stabilized with Lime and Phosphogypsum

Directory of Open Access Journals (Sweden)

Kumar Sujeet

2014-12-01

Full Text Available Engineering properties such as compaction, unconfined compressive strength, consistency limits, percentage swell, free swell index, the California bearing ratio and the consolidation of bentonite stabilized with lime and phosphogypsum are presented in this paper. The content of the lime and phosphogypsum varied from 0 to 10 %. The results reveal that the dry unit weight and optimum moisture content of bentonite + 8 % lime increased with the addition of 8 % phosphogypsum. The percentage of swell increased and the free swell index decreased with the addition of 8 % phosphogypsum to the bentonite + 8 % lime mix. The unconfined compressive strength of the bentonite + 8 % lime increased with the addition of 8 % phosphogypsum as well as an increase in the curing period up to 14 days. The liquid limit and plastic limit of the bentonite + 8 % lime increased, whereas the plasticity index remained constant with the addition of 8 % phosphogypsum. The California bearing ratio, modulus of subgrade reaction, and secant modulus increased for the bentonite stabilized with lime and phosphogypsum. The coefficient of the consolidation of the bentonite increased with the addition of 8 % lime and no change with the addition of 8 % phosphogypsum.

First evidence of lime burning in southern Scandinavia: lime kilns found at the royal residence on the west bank of Lake Tissø

DEFF Research Database (Denmark)

Henriksen, Peter Steen; Holst, Sandie

2015-01-01

In connection with investigations of the aristocratic residence at Tissø from the Viking Age, the earliest evidence so far of lime burning in Denmark has been excavated. The excavations unearthed traces of up to five lime kilns which were subsequently dated to the end of the ninth century....... This corresponds well with the dating of the erection of the hall in the third construction phase at Fugledegård. Finds of mud-and-wattle with whitewashing show that the lime was used to whitewash the halls at Tissø in both the Germanic Iron Age and the Viking Age. Analyses of lime from the lime kilns...... and the whitewashed mud-and-wattle demonstrate that the raw material for the lime burning was mainly travertine deposited in spring water, but that bryozoan limestone was also used. The lime kilns were just under 2 m in diameter with stone-built edges, and there are indications that the superstructure may have been...

Lime stabilization of expansive soil from Sergipe - Brazil

Directory of Open Access Journals (Sweden)

Leite Rafaella

2016-01-01

Full Text Available Expansive soils are characterized by volumetric changes caused by variations in moisture. They can cause several damages to civil constructions, especially to lightweight structures, including cracks and fissures. Chemical stabilization through addition of lime is one of the most effective techniques used to treat this type of soil. Due to cationic exchanges, lime can significantly reduce swell potential. This research studied a disturbed sample of expansive soil collected in Nossa Senhora do Socorro – Sergipe, Brazil, through the following laboratory tests: sieve and hydrometer tests, Atterberg Limits, compaction, free swell and swell pressure. All direct and indirect methods mentioned in this paper indicated that the natural soil presented high to very high degree of expansion, which reached approximately 20% of free swell and nearly 200 kPa of swell pressure. In order to evaluate the effect of lime, the same tests were conducted in soil-lime mixtures, using lime contents of 3%, 6% and 9%. The results confirmed the efficiency of lime stabilization. It was noted that, as lime content increased, there was reduction of clay fraction and increment of silt fraction; plasticity index decreased to nearly its half; compaction curve was displaced; and free swell and swell pressure reduced significantly.

Baking Soda and Vinegar Rockets

Science.gov (United States)

Claycomb, James R.; Zachary, Christopher; Tran, Quoc

2009-01-01

Rocket experiments demonstrating conservation of momentum will never fail to generate enthusiasm in undergraduate physics laboratories. In this paper, we describe tests on rockets from two vendors that combine baking soda and vinegar for propulsion. The experiment compared two analytical approximations for the maximum rocket height to the…

Ring Formation in Lime Kilns; Ringbildning i Mesaugnar II

Energy Technology Data Exchange (ETDEWEB)

Dhak, Janice [AaF-Process AB, Stockholm (Sweden)

2003-07-15

The key to a cost efficient and high performance pulp production is low variations in the production level. Despite the fact that all pulp mills always work with improvements to eliminate problems with ring formations, AaF has at several mill seen that the operation of a lime kiln still often is disturbed by ring formation. In 1999 AAF made an extensive investigation of more than 10 lime kilns in Sweden, considering operational data, kiln data and lime chemical analyzes. The result pointed out the importance of how the lime kiln is operated and that dead load and contaminants in the lime was less important. The report suggested that it is the difference in the temperature between the flue gas and the lime that is of importance. There are no quantified process values available that guides for a 'best practice' way to run a lime kiln to avoid ring formation. The goal with this project has been to develop a strategy for operation of a kiln in a way that lowers the risk for ring formation. The results from simulations of a number of lime kilns in this project could not proof that a low difference in the temperature between the flue gas and the lime was the main cause of problems with ring formation and thus it was not possible to quantify the optimal difference to avoid rings. Probably the most important information from the simulations was that it is not the temperature difference in number of degrees that is of importance, rather the fact that the temperature difference in the kalcining zone varies, and time to time reach below the critical level were lime occasionally is cooled down. It can be the case if the temperature profile of the flue gas temporarily changes or if the lime mud temperature profile is changed. The reason for changes in the temperature profile is discussed in the report. The most important factors discussed are: Variations in the energy input e.g. oil and methanol/strong gases in cocombustion. One single fuel is easier to control

Effect of the preparation of lime putties on their properties.

Science.gov (United States)

Navrátilová, Eva; Tihlaříková, Eva; Neděla, Vilém; Rovnaníková, Pavla; Pavlík, Jaroslav

2017-12-08

In the study of lime as the basic component of historical mortars and plasters, four lime putties prepared from various kinds of lime of various granulometry and by various ways of preparation were evaluated. The rheological properties and micro-morphologic changes, growing of calcite crystals, and rate of carbonation were monitored. The lime putty prepared from lump lime achieves the best rheological properties, yield stress 214.7 Pa and plastic viscosity 2.6 Pa·s. The suitability of this lime putty was checked by testing the development of calcium hydroxide and calcite crystals using scanning electron microscopy and environmental scanning electron microscopy. The disordered crystals of calcium hydroxide exhibit better carbonation resulting in the large crystals of calcite; therefore, the mortar prepared from the lump lime has the highest flexural strength and compressive strength 0.8/2.5 MPa, its carbonation is the fastest and exhibits the longest durability. Also, thanks to the micro-morphological characterization of samples in their native state by means of environmental scanning electron microscopy, the new way of lime putty preparation by mixing was proven. The preparation consists in the mechanical crash of the lime particles immediately after hydration. This enables the properties of putty prepared from lump lime to be nearly reached.

MONITORING OF WILD BEES IN POSTINDUSTRIAL WASTELANDS IN THE KUJAWY REGION

Directory of Open Access Journals (Sweden)

Lucyna Twerd

2017-04-01

Full Text Available Species diversity of pollinating insects was studied in areas affected by soda and lime industry in the Kujawy region (central Poland. Environmental monitoring was conducted near 3 industrial plants related to lime processing: Soda-Mątwy S.A. in Inowrocław, Janiksoda S.A. in Janikowo, and Trzuskawica S.A. in Bielawy. We recorded there 183 species of wild bees (Hymenoptera: Apoidea: Apiformes. The species that are widespread in the study area, i.e. common to all the 3 localities, accounted for about 50%, while those observed only locally, i.e. associated with only 1 industrial area, accounted for 25%. In the analysed period (2007-2010, we confirmed the occurrence of most of the species recorded: 78% in the areas affected by soda industry and 55% in those affected by lime industry. The presented results indicate that, surprisingly, postindustrial wastelands (including human-made and strongly degraded habitats can create favourable conditions for stable populations of many species of insects, also of the monitored wild bees.

Freeze concentration of lime juice

Directory of Open Access Journals (Sweden)

Ampawan Tansakul

2008-11-01

Full Text Available The main objective of this research was to study the effects of processing conditions, i.e. cooling medium temperature (-6, -12 and -18C and scraper blade rotational speed (50, 100 and 150 rpm on the freeze concentration of lime juice. The initial soluble solid content of lime juice was 7.6 Brix. Results showed that soluble solid content of lime juice increased as cooling medium temperature decreased while scraper blade rotational speed increased. It was also found that the processing condition with -18˚C cooling medium temperature and 150 rpm rotational speed of the scraper blade was the best among all studied conditions, although the loss of the soluble solids with ice crystals during ice separation was relatively high at 35%.

Removal of phosphate from greenhouse wastewater using hydrated lime.

Science.gov (United States)

Dunets, C Siobhan; Zheng, Youbin

2014-01-01

Phosphate (P) contamination in nutrient-laden wastewater is currently a major topic of discussion in the North American greenhouse industry. Precipitation of P as calcium phosphate minerals using hydrated lime could provide a simple, inexpensive method for retrieval. A combination of batch experiments and chemical equilibrium modelling was used to confirm the viability of this P removal method and determine lime addition rates and pH requirements for greenhouse wastewater of varying nutrient compositions. Lime: P ratio (molar ratio of CaMg(OH)₄: PO₄‒P) provided a consistent parameter for estimating lime addition requirements regardless of initial P concentration, with a ratio of 1.5 providing around 99% removal of dissolved P. Optimal P removal occurred when lime addition increased the pH from 8.6 to 9.0, suggesting that pH monitoring during the P removal process could provide a simple method for ensuring consistent adherence to P removal standards. A Visual MINTEQ model, validated using experimental data, provided a means of predicting lime addition and pH requirements as influenced by changes in other parameters of the lime-wastewater system (e.g. calcium concentration, temperature, and initial wastewater pH). Hydrated lime addition did not contribute to the removal of macronutrient elements such as nitrate and ammonium, but did decrease the concentration of some micronutrients. This study provides basic guidance for greenhouse operators to use hydrated lime for phosphate removal from greenhouse wastewater.

Use of demolition residues construction in soil-lime bricks

International Nuclear Information System (INIS)

Figueiredo, S.S.; Silva, C.G.; Silva, I.A.; Neves, G.A.

2011-01-01

Besides being responsible for several environmental damage caused by its residues, the construction industry is also considered the greatest natural resources consumer. When finely ground, such residues can exhibit cementing properties, which may replace part of the lime used in the manufacture of soil-lime bricks. This study aimed to verify the viability of using demolition residues (DR) in soil-lime bricks without structural function. For this, test specimens were prepared using mixes in a 1:10 ratio of lime:soil and embedding residue in partial replacement of lime in the proportions of 25%, 50% and 75%. The test specimens were submitted to curing periods of 28 and 52 days, then it was determined the compression strength. The results showed that when embedded on moderate percentages, demolition residues construction can be used in the production of soil-lime bricks. (author)

The association of soda sales tax and school nutrition laws: a concordance of policies.

Science.gov (United States)

Greathouse, K Leigh; Chriqui, Jamie; Moser, Richard P; Agurs-Collins, Tanya; Perna, Frank M

2014-10-01

The current research examined the association between state disfavoured tax on soda (i.e. the difference between soda sales tax and the tax on food products generally) and a summary score representing the strength of state laws governing competitive beverages (beverages that compete with the beverages in the federally funded school lunch programme) in US schools. The Classification of Laws Associated with School Students (CLASS) summary score reflected the strength of a state's laws restricting competitive beverages sold in school stores, vending machines, school fundraisers and à la carte cafeteria items. Bridging the Gap (BTG) is a nationally recognized research initiative that provided state-level soda tax data. The main study outcome was the states' competitive beverage summary scores for elementary, middle and high school grade levels, as predicted by the states' disfavoured soda tax. Univariate and multivariate analyses were conducted, adjusting for year and state. Data from BTG and CLASS were used. BTG and CLASS data from all fifty states and the District of Columbia from 2003 to 2010 were used. A higher disfavoured soda sales tax was generally associated with an increased likelihood of having strong school beverage laws across grade levels, and especially when disfavoured soda sales tax was >5 %. These data suggest a concordance between states' soda taxes and laws governing beverages sold in schools. States with high disfavoured sales tax on soda had stronger competitive beverage laws, indicating that the state sales tax environment may be associated with laws governing beverage policy in schools.

Molecular identification of Nocardia species using the sodA gene

Directory of Open Access Journals (Sweden)

K. Sánchez-Herrera

2017-09-01

Full Text Available Currently for bacterial identification and classification the rrs gene encoding 16S rRNA is used as a reference method for the analysis of strains of the genus Nocardia. However, it does not have enough polymorphism to differentiate them at the species level. This fact makes it necessary to search for molecular targets that can provide better identification. The sodA gene (encoding the enzyme superoxide dismutase has had good results in identifying species of other Actinomycetes. In this study the sodA gene is proposed for the identification and differentiation at the species level of the genus Nocardia. We used 41 type species of various collections; a 386 bp fragment of the sodA gene was amplified and sequenced, and a phylogenetic analysis was performed comparing the genes rrs (1171 bp, hsp65 (401 bp, secA1 (494 bp, gyrB (1195 bp and rpoB (401 bp. The sequences were aligned using the Clustal X program. Evolutionary trees according to the neighbour-joining method were created with the programs Phylo_win and MEGA 6. The specific variability of the sodA genus of the genus Nocardia was analysed. A high phylogenetic resolution, significant genetic variability, and specificity and reliability were observed for the differentiation of the isolates at the species level. The polymorphism observed in the sodA gene sequence contains variable regions that allow the discrimination of closely related Nocardia species. The clear specificity, despite its small size, proves to be of great advantage for use in taxonomic studies and clinical diagnosis of the genus Nocardia.

Recovery of drinking water and valuable minerals from acid mine drainage using an integration of magnesite, lime, soda ash, CO(sub)2 and reverse osmosis treatment processes

CSIR Research Space (South Africa)

Masindi, Vhahangwele

2017-08-01

Full Text Available that drinking water, metals, gypsum, hydrated lime/limestone were recovered from the treatment process as valuable resources. This was confirmed by X-ray diffraction (XRD) and X-ray Fluorescence (XRF). Morphological properties of initial and recovered minerals...

Simple Analysis of Historical Lime Mortars

Science.gov (United States)

Pires, Joa~o

2015-01-01

A laboratory experiment is described in which a simple characterization of a historical lime mortar is made by the determination of its approximate composition by a gravimetric method. Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) are also used for the qualitative characterization of the lime mortar components. These…

Comparative study of engineering properties of two-lime waste tire particle soil and soil with lime/loess ratio of 3:7

Science.gov (United States)

Tiecheng, Yan; Xingyuan, Zhang; Hongping, Yang

2018-03-01

This study describes an analytical comparison of the engineering characteristics of two-lime waste tire particle soil and soil with lime/loess ratio of 3:7 using density measurements, results of indoor consolidation tests, and direct shear tests to examine the strength and deformation characteristics. It investigates the engineering performance of collapsible loess treated with waste tire particles and lime. The results indicate that (1) the shear strength of the two-lime waste tire particle soils increases continuously with soil age; and (2) the two-lime waste tire particle soils are light-weight, strong, and low-deformation soils, and can be applied primarily to improve the foundation soil conditions in areas with collapsible loess soils. This could address the problem of used tire disposal, while providing a new method to consider and manage collapsible loess soils.

Lime treatment of stabilized leachates

International Nuclear Information System (INIS)

Renou, S.; Poulain, S.; Givaudan, J. G.; Sahut, C.; Moulin, P.

2009-01-01

Reverse Osmosis is the most widely used method for treating municipal solid waste landfill leachates, since it produces a permeate in compliance with reject requirements. However, the efficiency of this process at the industrial scale is limited mainly because of membrane fouling and the high osmotic pressures involved. Although lime precipitation is traditionally used to eliminate the temporary hardness of water by de-carbonation, it has also been shown to be highly efficient in removing humic substances which are known to have strong fouling potential towards membranes. Our objective is to study the lime/leachate physico-chemistry, in order to determine the potential of the lime precipitation as pre-treatment for reverse osmosis. The results show that the lime treatment makes it possible (i) to act efficiently on the inorganic fraction of leachates through a de-carbonation mechanism which entails massive precipitation of the carbonates under the form of CaCO 3 , (ii) to eliminate by co-precipitation the high Molecular Weight (MW) organic macromolecules (≥ 50, 000 g.mol -1 ) such as humic acids, and (iii) to generate a stable residue that can be easily stored at a landfill. The reverse osmosis step will be facilitated through significant reduction of the osmotic pressures and prevention of membrane fouling. (authors)

[Modification of fasting blood glucose in adults with diabetes mellitus type 2 after regular soda and diet soda intake in the State of Querétaro, Mexico].

Science.gov (United States)

Olalde-Mendoza, Liliana; Moreno-González, Yazmín Esmeralda

2013-06-01

The objective of the study was to compare the modification of fasting blood glucose in adults with diabetes mellitus type 2 after intake of regular soda and diet soda. We conducted a randomized clinical trial in clinics of Instituto Mexicano del Seguro Social in Querétaro, México. We included 80 patients with diabetes (mean weight 74.2 +/- 13.66, BMI 30.5 +/- 4.305, waist 98.2 +/- 12.9 and time evolution of diabetes 3.8 +/- 3.009) who were asked to come with fasting for 8 hours and without taking any medicine before testing. They were divided into two groups of 40 subjects, to whom was measured fasting blood glucose after the ingestion of 200 ml of diet soda (with aspartame and acesulfame potassium) or regular soda (without sweetener) we measure glucose at 10, 15 and 30 minutes. For statistical analysis performed we used Student's t-test for dependent and independent samples, and paired t-test, and chi square test (chi2). Capillary glucose levels at 10 minutes were -34.52 and -25.41%, at 15 minutes -48.8 and -36.2% and at 30 minutes 57.75 and 43.6% of absolute and relative differences, with p = 0.000. In conclusion, according to the observations, diet soda doesn't increased blood glucose levels, with a significant difference in fasting decreased at 30 minutes.

Hydrogen peroxide and caustic soda: Dancing with a dragon while bleaching

Science.gov (United States)

Peter W. Hart; Carl Houtman; Kolby Hirth

2013-01-01

When hydrogen peroxide is mixed with caustic soda, an auto-accelerating reaction can lead to generation of significant amounts of heat and oxygen. On the basis of experiments using typical pulp mill process concentration and temperatures, a relatively simple kinetic model has been developed. Evaluation of these model results reveals that hydrogen peroxide-caustic soda...

Lime in gold and uranium mining

International Nuclear Information System (INIS)

Van Staden, C.M.

1979-01-01

In this article the author discusses the role of lime in gold and uranium extraction and looks more closely at the industry's efforts to improve the environment by vegetation of sand dumps and slimes dams. He then comes to the conclusion that lime has been and still is the most effective, practical and cheapest chemical that can be used in the South African gold and uranium mining industry to settle pulps, protect cyanide solutions, aid the vegetation of dumps and neutralise acidic waters and residues. The gold and uranium industry is very pollution concious, and in South Africa the importance of the role that lime plays in combating air and water pollution cannot be over emphasised

The Untapped Power of Soda Taxes: Incentivizing Consumers, Generating Revenue, and Altering Corporate Behavior.

Science.gov (United States)

Roache, Sarah A; Gostin, Lawrence O

2017-06-14

Globally, soda taxes are gaining momentum as powerful interventions to discourage sugar consumption and thereby reduce the growing burden of obesity and non-communicable diseases (NCDs). Evidence from early adopters including Mexico and Berkeley, California, confirms that soda taxes can disincentivize consumption through price increases and raise revenue to support government programs. The United Kingdom's new graduated levy on sweetened beverages is yielding yet another powerful impact: soda manufacturers are reformulating their beverages to significantly reduce the sugar content. Product reformulation - whether incentivized or mandatory - helps reduce overconsumption of sugars at the societal level, moving away from the long-standing notion of individual responsibility in favor of collective strategies to promote health. But as a matter of health equity, soda product reformulation should occur globally, especially in low- and middleincome countries (LMICs), which are increasingly targeted as emerging markets for soda and junk food and are disproportionately impacted by NCDs. As global momentum for sugar reduction increases, governments and public health advocates should harness the power of soda taxes to tackle the economic, social, and informational drivers of soda consumption, driving improvements in food environments and the public's health. © 2017 The Author(s); Published by Kerman University of Medical Sciences. This is an open-access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Time evolution of pore system in lime - Pozzolana composites

Science.gov (United States)

Doleželová, Magdaléna; Čáchová, Monika; Scheinherrová, Lenka; Keppert, Martin

2017-11-01

The lime - pozzolana mortars and plasters are used in restoration works on building cultural heritage but these materials are also following the trend of energy - efficient solutions in civil engineering. Porosity and pore size distribution is one of crucial parameters influencing engineering properties of porous materials. The pore size distribution of lime based system is changing in time due to chemical processes occurring in the material. The present paper describes time evolution of pore system in lime - pozzolana composites; the obtained results are useful in prediction of performance of lime - pozzolana systems in building structures.

Lime and gypsum application on the wheat crop

Directory of Open Access Journals (Sweden)

Caires Eduardo Fávero

2002-01-01

Full Text Available Root growth and crop yield can be affected by chemical modifications of the soil profile owing to lime and gypsum applications. A field trial was carried out on a dystrophic Clayey Rhodic Hapludox at Ponta Grossa, PR, Brazil, aiming to evaluate lime (without or with incorporation into the soil and gypsum effects on root growth, mineral nutrition and grain yield of wheat (cv. OR 1. A randomized complete block design was used, with three replications, in a split-plot experiment. Treatments with dolomitic limestone (without lime and 4.5 t ha-1 of lime applied on the surface, in total rate and 1/3 of the requirement per year during 3 years, or incorporated into the soil were applied in July 1998 (main plots and the rates of gypsum (0, 3, 6 and 9 t ha-1 in October 1998 (subplots. Wheat was evaluated in the 2000 winter season. In conditions of water deficit absence, there was no limitation in root growth in depth, for exchangeable Ca of 6 mmol c dm-3. Lime incorporation of lime increased the Mg concentration in the leaves, but wheat yield was not influenced by the correction of soil acidity through liming treatments. Gypsum increased the concentrations of Ca and S in wheat leaves, with significant effects on grain yield. The critical level of S-SO4(2- in the 0-20 cm soil layer, extracted by ammonium acetate 0.5 mol L-1 in acetic acid 0.25 mol L-1, was 25.8 mg dm-3.

Balancing guava nutrition with liming and fertilization

Directory of Open Access Journals (Sweden)

Amanda Hernandes

2012-12-01

Full Text Available Guava response to liming and fertilization can be monitored by tissue testing. Tissue nutrient signature is often diagnosed against nutrient concentration standards. However, this approach has been criticized for not considering nutrient interactions and to generate numerical biases as a result of data redundancy, scale dependency and non-normal distribution. Techniques of compositional data analysis can control those biases by balancing groups of nutrients, such as those involved in liming and fertilization. The sequentially arranged and orthonormal isometric log ratios (ilr or balances avoid numerical bias inherent to compositional data. The objectives were to relate tissue nutrient balances with the production of "Paluma" guava orchards differentially limed and fertilized, and to adjust the current patterns of nutrient balance with the range of more productive guava trees. It was conducted one experiment of 7-yr of liming and three experiments of 3-yr with N, P and K trials in 'Paluma' orchards on an Oxisol. Plant N, P, K, Ca and Mg were monitored yearly. It was selected the [N, P, K | Ca, Mg], [N, P | K], [N | P] and [Ca | Mg] balances to set apart the effects of liming (Ca-Mg and fertilizers (N-K on macronutrient balances. Liming largely influenced nutrient balances of guava in the Oxisol while fertilization was less influential. The large range of guava yields and nutrient balances allowed defining balance ranges and comparing them with the critical ranges of nutrient concentration values currently used in Brazil and combined into ilr coordinates.

46 CFR 148.04-23 - Unslaked lime in bulk.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Unslaked lime in bulk. 148.04-23 Section 148.04-23... HAZARDOUS MATERIALS IN BULK Special Additional Requirements for Certain Material § 148.04-23 Unslaked lime in bulk. (a) Unslaked lime in bulk must be transported in unmanned, all steel, double-hulled barges...

Saliva secretion difference before and after rinsing with baking soda on menopause women

Directory of Open Access Journals (Sweden)

Dewi Anggraeni

2007-03-01

Full Text Available Menopause women can experience a decrease in saliva secretion (decrease. To understand the clear picture about saliva secretion, the volume, flow rate, pH and viscosity were then measured. The aim of this research was to obtain a picture about the difference of saliva secretion before and after rinsing with baking soda on menopause women. The type of the research used was a laboratory quasi-experiment with comparative descriptive form. The technique used in this research is the survey method, and samples were taken using the multistage cluster random sampling method, and t-student statistical analysis. This research was conducted with the saliva collected with spitting method on 45 menopause women. The results show that the average volume, flow rate, pH and viscosity before rinsing with baking soda was 1.79 ml, 0.18 ml/minute, 7.40 and 0.81 mm2/second. The average volume, flow rate, pH and viscosity after rinsing with baking soda were 2.66 ml; 0.27 ml/minute; 8.67 and 0.78 mm2/second. Statistical analysis t-student on α = 0.05 shows volume changes, flow rate, pH and saliva viscosity before and after rinsing with baking soda was 0.873; 0.086; 1.273 and 0.037 respectively. The conclusion shows a significant difference between saliva secretion before and after rinsing with baking soda, and saliva secretion after rinsing with baking soda on menopause women.

Effect of lime concentration on gelatinized maize starch dispersions properties.

Science.gov (United States)

Lobato-Calleros, C; Hernandez-Jaimes, C; Chavez-Esquivel, G; Meraz, M; Sosa, E; Lara, V H; Alvarez-Ramirez, J; Vernon-Carter, E J

2015-04-01

Maize starch was lime-cooked at 92 °C with 0.0-0.40% w/w Ca(OH)2. Optical micrographs showed that lime disrupted the integrity of insoluble remnants (ghosts) and increased the degree of syneresis of the gelatinized starch dispersions (GSD). The particle size distribution was monomodal, shifting to smaller sizes and narrower distributions with increasing lime concentration. X-ray patterns and FTIR spectra showed that crystallinity decreased to a minimum at lime concentration of 0.20% w/w. Lime-treated GSD exhibited thixotropic and viscoelastic behaviour. In the linear viscoelastic region the storage modulus was higher than the loss modulus, but a crossover between these moduli occurred in the non-linear viscoelastic region. The viscoelastic properties decreased with increased lime concentration. The electrochemical properties suggested that the amylopectin-rich remnants and the released amylose contained in the continuous matrix was firstly attacked by calcium ions at low lime levels (<0.20% w/w), disrupting the starch gel microstructure. Copyright © 2014 Elsevier Ltd. All rights reserved.

Low Velocity Sphere Impact of a Borosilicate Glass

Energy Technology Data Exchange (ETDEWEB)

Morrissey, Timothy G [ORNL; Ferber, Mattison K [ORNL; Wereszczak, Andrew A [ORNL; Fox, Ethan E [ORNL

2012-05-01

This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (< 30 m/s or < 65 mph) ball impact testing of Borofloat borosilicate glass, and is a follow-up to a similar study completed by the authors on Starphire soda-lime silicate glass last year. The response of the borosilicate glass to impact testing at different angles was also studied. The Borofloat glass was supplied by the US Army Research Laboratory and its tin-side was impacted or indented. The intent was to better understand low velocity impact response in the Borofloat. Seven sphere materials were used whose densities bracket that of rock: borosilicate glass, soda-lime silicate glass, silicon nitride, aluminum oxide, zirconium oxide, carbon steel, and a chrome steel. A gas gun or a ball-drop test setup was used to produce controlled velocity delivery of the spheres against the glass tile targets. Minimum impact velocities to initiate fracture in the Borofloat were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between the seven sphere-Borofloat-target combinations. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) BS glass responded similarly to soda-lime silicate glass when spherically indented but quite differently under sphere impact conditions; (2) Frictional effects contributed to fracture initiation in BS glass when it spherically indented. This effect was also observed with soda-lime silicate glass; (3) The force necessary to initiate fracture in BS glass under spherical impact decreases with increasing elastic modulus of the sphere material. This trend is opposite to what was observed with soda-lime silicate glass. Friction cannot explain this trend and the authors do not have a legitimate explanation for it yet; (4) The force necessary to initiate contact-induced fracture is higher under dynamic conditions than under quasi-static conditions. That

[Study on Archaeological Lime Powders from Taosi and Yinxu Sites by FTIR].

Science.gov (United States)

Wei, Guo-feng; Zhang, Chen; Chen, Guo-liang; He, Yu-ling; Gao, Jiang-tao; Zhang, Bing-jian

2015-03-01

Archaeological lime powders samples from Taosi and Yinxu sites, natural limestone and experimentally prepared lime mortar were investigated by means of Fourier transform infrared spectrometry (FTIR) to identify the raw material of lime powders from Taosi and Yinxu sites. Results show that ν2/ν4 ratio of calcite resulted from carbonation reaction of man-made lime is around 6.31, which is higher than that of calcite in natural limestone and reflects the difference in the disorder of calcite crystal structure among the natural limestone and prepared lime mortar. With additional grinding, the values of v2 and ν4 in natural limestone and prepared lime mortar decrease. Meanwhile, the trend lines of ν2 versus ν4 for calcite in experimentally prepared lime mortar have a steeper slope when compared to calcite in natural limestone. These imply that ν2/ν4 ratio and the slope of the trend lines of ν2 versus ν4 can be used to determine the archaeological man-made lime. Based on the experiment results, it is possible that the archaeological lime powder from Taosi and Yinxu sites was prepared using man-made lime and the ancient Chinese have mastered the calcining technology of man-made lime in the late Neolithic period about 4 300 years ago.

40 CFR 63.443 - Standards for the pulping system at kraft, soda, and semi-chemical processes.

Science.gov (United States)

2010-07-01

... Paper Industry § 63.443 Standards for the pulping system at kraft, soda, and semi-chemical processes. (a... operator of each pulping system using a semi-chemical or soda process subject to the requirements of this... kraft, soda, and semi-chemical processes. 63.443 Section 63.443 Protection of Environment ENVIRONMENTAL...

Effects of corn cob ash on lime stabilized lateritic soil

Science.gov (United States)

Nnochiri, Emeka Segun

2018-03-01

This study assesses the effects of Corn Cob Ash (CCA) on lime-stabilized lateritic soil. Preliminary tests were carried out on the natural soil sample for purpose of identification and classification. Lime being the main stabilizing material was thoroughly mixed with the soil sample to determine the optimum lime requirement of the sample as a basis for evaluating the effects of the CCA. The optimum lime requirement was 10%. The CCA was thereafter added to the lime stabilized soil in varying proportions of 2, 4, 6, 8 and 10%. Unsoaked CBR increased from 83% at 0% CCA to highest value of 94% at 4% CCA. Unconfined Compressive Strength (UCS) values increased from 1123kN/m2 at 0% CCA to highest value of 1180kN/m2 at 4% CCA. It was therefore concluded that CCA can serve as a good complement for lime stabilization in lateritic soil.

Properties Of Soda/Yttria/Silica Glasses

Science.gov (United States)

Angel, Paul W.; Hann, Raiford E.

1994-01-01

Experimental study of glass-formation compositional region of soda/ yttria/silicate system and of selected physical properties of glasses within compositional region part of continuing effort to identify glasses with high coefficients of thermal expansion and high softening temperatures, for use as coatings on superalloys and as glass-to-metal seals.

Optimization of lime treatment processes

International Nuclear Information System (INIS)

Zinck, J. M.; Aube, B. C.

2000-01-01

Lime neutralization technology used in the treatment of acid mine drainage and other acidic effluents is discussed. Theoretical studies and laboratory experiments designed to optimize the technology of lime neutralization processes and to improve the cost efficiency of the treatment process are described. Effluent quality, slaking temperature, aeration, solid-liquid separation, sludge production and geochemical stability have been studied experimentally and on site. Results show that through minor modification of the treatment process, costs, sludge volume generated, and metal released to the environment can be significantly reduced. 17 refs., 4 figs

Soda-anthraquinone, kraft and organosolv pulping of holm oak trimmings.

Science.gov (United States)

Alaejos, J; López, F; Eugenio, M E; Tapias, R

2006-11-01

The operating conditions for an organosolv (ethyleneglycol) and two alkaline (soda-anthraquinone and kraft) processes for obtaining cellulose pulp and paper from holm oak (Quercus ilex) wood trimmings were optimized. A range of variation for each process variable (viz. temperature, cooking time and soda or ethyleneglycol concentration) was established and a central composite experimental design involving three independent variables at three different variation levels was applied. The results obtained with the three cooking processes used were compared and those provided by the kraft process were found to be the best. Thus, the tensile index values it provided (5.9-16.3 N m/g) were 23.7% and 41.5% better than those obtained with the soda-AQ and ethyleneglycol processes, respectively. Also, the kraft process provided the best burst index, brightness and kappa number values. Based on the optimum working ranges, the temperature and cooking time were the variables resulting in the most and least marked changes, respectively, in pulp properties.

Characteristic Asphalt Concrete Wearing Course (ACWC) Using Variation Lime Filler

Science.gov (United States)

Permana, R. A.; Pramesti, F. P.; Setyawan, A.

2018-03-01

This research use of lime filler Sukaraja expected add durability layers of concrete pavement is asphalt damage caused by the weather and load traffic. This study attempts to know how much value characteristic Marshall on a mixture of concrete asphalt using lime filler. This research uses experimental methods that is with a pilot to get results, thus will look filler utilization lime on construction concrete asphalt variation in filler levels 2 %, 3 %, 4 %.The results showed that the use of lime filler will affect characteristic a mixture of concrete asphalt. The more filler chalk used to increase the value of stability. On the cretaceous filler 2 % value of stability is 1067,04 kg. When lime filler levels added to the levels of filler 4 %, the value of stability increased to 1213,92 kg. The flexibility increased the number of filler as levels lime 2 % to 4 % suggests that are conducted more stiff mix.

Liming as a method to remedy lakes contaminated by radiostrontium

International Nuclear Information System (INIS)

Haakanson, Lars

2003-01-01

This work has identified the characteristics regulating lake sensitivity to 90 Sr-contamination and why certain lakes are likely to respond positively to lake liming (Ca-treatment) and when this would not be a feasible or economic remedial measure to lower 90 Sr-levels in fish. The results demonstrate that liming would work best in (1) small, (2) low-productive, (3) oligohumic, (4) acid lakes with (5) low initial Ca-concentrations. It is important to start the liming as soon as possible after the fallout. The liming model discussed in this work can be used to calculate the changes in lake Ca-concentrations and the duration of the liming. The Sr-model can be used to calculate changes in Sr-levels in water, sediments and fish. At best, these simulations indicate that it is realistic to expect that lake liming can reduce peak levels of 90 Sr in fish by 25-40%

Short-term responses of wetland vegetation after liming of an Adirondack watershed

Energy Technology Data Exchange (ETDEWEB)

Mackun, I.R.; Leopold, D.J.; Raynal, D.J. (State Univ. of New York, Syracuse, NY (United States))

1994-08-01

Watershed liming has been suggested as a long-term mitigation strategy for lake acidity, particularly in areas subject to high levels of acidic deposition. However, virtually no information has been available on the impacts of liming on wetland vegetation. In 1989, 1100 Mg of limestone (83.5% CaCO[sub 3]) were aerially applied to 48% (100 ha) of the Woods Lake watershed in the west-central Adirondack region of New York as part of the first comprehensive watershed liming study in North America. We inventoried wetland vegetation in 1.0-m[sup 2] plots before liming and during the subsequent 2 yr. Within this period liming influenced the cover, frequency, or importance values of only 6 of 64 wetland taxa. The cover of Sphagnum spp. and of the cespitose sedge Carex interior decreased in control relative to limed plots, and cover of the rhizomatous sedge Cladium mariscoides increased nearly threefold in limed areas. These two sedges, which are relatively tall, are characteristic of more calcareous habitats. Cover of the grass Muhlenbergia uniflora, cover and importance were adversely affected or inhibited by lime. It is unclear whether liming directly inhibited the growth of these three small-statured species, or whether the adverse effects of lime were mediated through shifts in competitive interactions with other species. The limited responses that we observed to liming, along with changes that occurred in control plots over the study period, may indicate that in the short term watershed liming was no more of a perturbation than the environmental factors responsible for natural annual variation in wetland communities.

Liming impacts on soils, crops and biodiversity in the UK: A review.

Science.gov (United States)

Holland, J E; Bennett, A E; Newton, A C; White, P J; McKenzie, B M; George, T S; Pakeman, R J; Bailey, J S; Fornara, D A; Hayes, R C

2018-01-01

Fertile soil is fundamental to our ability to achieve food security, but problems with soil degradation (such as acidification) are exacerbated by poor management. Consequently, there is a need to better understand management approaches that deliver multiple ecosystem services from agricultural land. There is global interest in sustainable soil management including the re-evaluation of existing management practices. Liming is a long established practice to ameliorate acidic soils and many liming-induced changes are well understood. For instance, short-term liming impacts are detected on soil biota and in soil biological processes (such as in N cycling where liming can increase N availability for plant uptake). The impacts of liming on soil carbon storage are variable and strongly relate to soil type, land use, climate and multiple management factors. Liming influences all elements in soils and as such there are numerous simultaneous changes to soil processes which in turn affect the plant nutrient uptake; two examples of positive impact for crops are increased P availability and decreased uptake of toxic heavy metals. Soil physical conditions are at least maintained or improved by liming, but the time taken to detect change varies significantly. Arable crops differ in their sensitivity to soil pH and for most crops there is a positive yield response. Liming also introduces implications for the development of different crop diseases and liming management is adjusted according to crop type within a given rotation. Repeated lime applications tend to improve grassland biomass production, although grassland response is variable and indirect as it relates to changes in nutrient availability. Other indicators of liming response in grassland are detected in mineral content and herbage quality which have implications for livestock-based production systems. Ecological studies have shown positive impacts of liming on biodiversity; such as increased earthworm abundance that

Action time effect of lime on its depressive ability for pyrite

Institute of Scientific and Technical Information of China (English)

Tichang Sun

2004-01-01

Two sample groups of bulk concentrates consisting mainly of pyrite and chalcopyrite from Daye and Chenghchao Mines in Hubei Province of China were used to investigate the effect of the action time of lime on its depressive ability for pyrite. The experimental results conducted with different samples and collectors showed that the action time between lime and pyrite markedly influences the depressive ability of lime. The depressive ability of lime increased with the action time increasing. It was also proved that the depressive results obtained at a large lime dosage after a shorter action time are similar to those obtained at a small lime dosage after a longer action time. The increase of depressive ability of lime after a longer action time is because that there are different mechanisms in different action time. The composition on the surface of pyrite acted for different time with lime was studied by using ESCA (Electron Spectroscopic Chemical Analysis). The results showed that iron hydroxide and calcium sulphate formed on the pyrite surface at the presence of lime in the pulp but the amounts of iron hydroxide and calcium sulphate were different at different action time. At the beginning action time the compound formed on the pyrite surface was mainly calcium sulphate and almost no iron hydroxide formed; but with the action time increasing, iron hydroxide formed. The longer the action time, the more iron hydroxide and the less calcium sulphate formed. It was considered that the stronger depressive ability of lime after a longer action time is because more iron hydroxide forms on the pyrite surface.

Experimental investigation and constitutive model for lime mudstone.

Science.gov (United States)

Wang, Junbao; Liu, Xinrong; Zhao, Baoyun; Song, Zhanping; Lai, Jinxing

2016-01-01

In order to investigate the mechanical properties of lime mudstone, conventional triaxial compression tests under different confining pressures (0, 5, 15 and 20 MPa) are performed on lime mudstone samples. The test results show that, from the overall perspective of variation law, the axial peak stress, axial peak strain and elastic modulus of lime mudstone tend to gradually increase with increasing confining pressure. In the range of tested confining pressure, the variations in axial peak stress and elastic modulus with confining pressure can be described with linear functions; while the variation in axial peak strain with confining pressure can be reflected with a power function. To describe the axial stress-strain behavior in failure process of lime mudstone, a new constitutive model is proposed, with the model characteristics analyzed and the parameter determination method put forward. Compared with Wang' model, only one parameter n is added to the new model. The comparison of predicted curves from the model and test data indicates that the new model can preferably simulate the strain softening property of lime mudstone and the axial stress-strain response in rock failure process.

Hydration products of lime-metakaolin pastes at ambient temperature with ageing

Energy Technology Data Exchange (ETDEWEB)

Gameiro, A., E-mail: agameiro@lnec.pt [National Laboratory of Civil Engineering, Materials Department, Av. do Brasil, 101, 1700 Lisbon (Portugal); Santos Silva, A., E-mail: ssilva@lnec.pt [National Laboratory of Civil Engineering, Materials Department, Av. do Brasil, 101, 1700 Lisbon (Portugal); Veiga, R., E-mail: rveiga@lnec.pt [National Laboratory of Civil Engineering, Buildings Department, Av. do Brasil, 101, 1700 Lisbon (Portugal); Velosa, A., E-mail: avelosa@ua.pt [Department of Civil Engineering, Geobiotec, University of Aveiro, Campus Universitario de Santiago, 3810-193 Aveiro (Portugal)

2012-05-10

Highlights: Black-Right-Pointing-Pointer We study the compounds formed in lime/MK blended pastes and their stability over time. Black-Right-Pointing-Pointer Different mixes of lime/MK pastes show different reaction kinetics during curing time, being the pozzolanic compounds formed directly proportional to the lime by MK replacement. Black-Right-Pointing-Pointer Some pozzolanic products are found to be unstable during the hydration reaction employed in our study. - Abstract: Mortars constituted of lime mixtures with pozzolanic additions have been extensively used in the past for the construction of historic and traditional buildings. This paper presents the results of blended pastes of lime and metakaolin (MK), namely compounds formed and their stability over time. This research is part of an extensive study aiming at the formulation of lime based mortars for restoration purposes. It has been shown for several years that MK has been applied in inorganic binders due to its capacity to react vigorously with calcium hydroxide (CH). In the presence of water originating a series of major hydrated phases, namely tetra calcium aluminate hydrate (C{sub 4}AH{sub 13}), calcium silicates hydrates (CSH) and calcium aluminium silicate hydrates (stratlingite - C{sub 2}ASH{sub 8}). Several blended pastes of lime and MK, with different substitution rates of lime by MK (wt%) were prepared and cured at a temperature of 20 Degree-Sign C and relative humidity RH > 95%. The phase composition of the formed hydrated phases was determined by X-ray diffraction (XRD) and simultaneous thermal analysis (TG-DTA). The obtained results showed that lime/MK pastes compositions displayed different reaction kinetics during curing time, being the pozzolanic products content directly proportional to the substitution rate of lime by MK. Also, a relationship between the increase stratlingite content and the MK substitution rate of lime by MK was found.

Spatial distribution of soda straws growth rates of the Coufin Cave (Vercors, France

Directory of Open Access Journals (Sweden)

Perrette Yves

2010-07-01

Full Text Available The Choranche Cave system (Vercors, France is an excellent locality for measuring the growth rates of large numbers soda straws. This is especially the case for the Coufin Cave, as enlargement of the cave entrance in 1875 led to a change in stalactite color from brown to white, thus providing a reliable chronomarker. The date of this brown-to-white calcite transition has been confirmed by lamina counting. We measured and georeferenced the growth-lengths of 306 soda straws in a 1m2 area of the roof of the Coufin Cave entrance chamber. Because of the very slow and sometimes inexistent water feeding of those stalactites, hydrochemistry analysis were not achieved and drop rate effect on growth were neglected; this study is based on a geomorphological and geostatistical work. By measuring a large number of soda straws in a very small area for which most of the parameters affecting stalactite growth could be considered uniform, and because flow rates are very slow (frequencies are always superior to 1 drop per half hour, we could ascribe differences in growth rates to variations in the global increase of water flow through the unsaturated matrix. Statistical and geostatistical analyses of the measurements showed that this set of similarly shaped stalactites actually consisted of three Gaussian populations with different mean growth rates: fast growth rate (FGR- mean of 0.92 mm.y-1, medium growth rate (MGR- mean of 0.47 mm.y-1 and low growth rate (LGR- 0.09 mm.y-1. Plotting the lengths and spatial distribution of the 20 longest FGR soda straws revealed that there is a rough pattern to the water flow through the cave roof. Even if no direction is statisticaly different from others, the observed directional pattern is consistent with local and regional tectonic observations. Plots of the spatial distribution of the soda straws show that FGR soda straws follow lines of regional geological stress, whereas MGR and LGR soda straws are more dispersed.

Peat Soil Stabilization using Lime and Cement

Directory of Open Access Journals (Sweden)

Mohd Zambri Nadhirah

2018-01-01

Full Text Available This paper presents a study of the comparison between two additive Lime and Cement for treating peat soil in term of stabilization. Peat and organic soils are commonly known for their high compressibility, extremely soft, and low strength. The aim of this paper is to determine the drained shear strength of treated peat soil from Perlis for comparison purposes. Direct Shear Box Test was conducted to obtain the shear strength for all the disturbed peat soil samples. The quick lime and cement was mixed with peat soil in proportions of 10% and 20% of the dry weight peat soil. The experiment results showed that the addition of additives had improved the strength characteristics of peat soil by 14% increment in shear strength. In addition, the mixture of lime with peat soil yield higher result in shear strength compared to cement by 14.07% and 13.5% respectively. These findings indicate that the lime and cement is a good stabilizer for peat soil, which often experienced high amount of moisture content.

Peat Soil Stabilization using Lime and Cement

Science.gov (United States)

Zambri, Nadhirah Mohd; Ghazaly, Zuhayr Md.

2018-03-01

This paper presents a study of the comparison between two additive Lime and Cement for treating peat soil in term of stabilization. Peat and organic soils are commonly known for their high compressibility, extremely soft, and low strength. The aim of this paper is to determine the drained shear strength of treated peat soil from Perlis for comparison purposes. Direct Shear Box Test was conducted to obtain the shear strength for all the disturbed peat soil samples. The quick lime and cement was mixed with peat soil in proportions of 10% and 20% of the dry weight peat soil. The experiment results showed that the addition of additives had improved the strength characteristics of peat soil by 14% increment in shear strength. In addition, the mixture of lime with peat soil yield higher result in shear strength compared to cement by 14.07% and 13.5% respectively. These findings indicate that the lime and cement is a good stabilizer for peat soil, which often experienced high amount of moisture content.

Prevalence of using baking soda in different types of most commonly consumed breads by Iranian people

Directory of Open Access Journals (Sweden)

Abolfazl Mohammadbeigi

2018-01-01

Full Text Available Background: Nowadays, in most bakeries in order to accelerate bread production process and reduce work pressure on bakers, harmful chemicals like baking soda are in use. Therefore, the aim of the present study was to investigate the prevalence of using baking soda in different types of most commonly consumed breads by Iranian people. Materials and Methods: This cross-sectional descriptive study was carried out on 234 bakeries in Qom, Iran, during 2017. The proportional stratified sampling method was used to select bakeries and bakers in different districts of Qom. Age, bakery experience, education of bakers and bread's pH were collected by a questionnaire and an electrical pH meter. Results: The results showed that seventy bakeries (29.9% of Qom were using baking soda in bread. The highest frequent use of baking soda was observed in Taftoon (38.7% and Lavash bread (31.5%. There was a significant difference between the use of baking soda and demographic variables such as age and literacy level. The attitude and knowledge of bakery employees about the complications of the baking soda were not appropriate. Conclusions: To reduce the use of baking soda and improve their knowledge and attitude, there is a need of strict supervision and monitoring by responsible organisations, especially the Ministry of Health.

Metabolic alkalosis secondary to baking soda treatment of a diaper rash.

Science.gov (United States)

Gonzalez, J; Hogg, R J

1981-06-01

A 4-month-old infant was seen with hypokalemic metabolic alkalosis that was associated with prior application of liberal amounts of sodium bicarbonate (baking soda) to a diaper rash. After exclusion of other etiologies of the infant's acid-base disturbance, a complete resolution occurred following discontinuation of the baking soda applications. This case report provides a reminder of the significant side effects that may result from the excessive use of a seemingly harmless household substance.

Plasticity, Swell-Shrink, and Microstructure of Phosphogypsum Admixed Lime Stabilized Expansive Soil

OpenAIRE

James, Jijo; Pandian, P. Kasinatha

2016-01-01

The study involved utilization of an industrial waste, Phosphogypsum (PG), as an additive to lime stabilization of an expansive soil. Three lime dosages, namely, initial consumption of lime (ICL), optimum lime content (OLC), and less than ICL (LICL), were identified for the soil under study for stabilizing the soil. Along with lime, varying doses of PG were added to the soil for stabilization. The effect of stabilization was studied by performing index tests, namely, liquid limit, plastic lim...

Towards the industrial solar production of lime

Energy Technology Data Exchange (ETDEWEB)

Meier, A.; Bonaldi, E. [QualiCal SA, Bergamo (Italy); Cella, G.M. [QualiCal SA, Bergamo (Italy); Lipinski, W.; Palumbo, R.; Steinfeld, A. [ETH Zuerich (Switzerland) and PSI; Wieckert, C.; Wuillemin, D.

2002-03-01

A new industrial concept that aims at the development of the chemical engineering technology for the solar production of lime is being examined. To establish the technical feasibility, a 10 kW solar reactor has been designed, constructed, and experimentally tested at a high-flux solar furnace. The quality of the produced solar lime meets industrial standards. (author)

Hydrogen Chloride Reaction with Lime and Limestone

DEFF Research Database (Denmark)

Erik Weinell, Claus; Jensen, Peter I.; Dam-Johansen, Kim

1992-01-01

The capacity of solid slaked lime and limestone for binding HCl from a gas phase has been investigated in the temperature range 60-1000 °C. The binding capacity is largest in the range 500-600 °C. However, for slaked lime in the presence of water, a large binding capacity is observed also below 150...

Cleaner production in the ammonia-soda industry: an ecological and economic study.

Science.gov (United States)

Kasikowski, T; Buczkowski, R; Lemanowska, E

2004-12-01

Five methods to reduce the negative influence of soda ash factories on the natural environment are presented: 1. obtaining calcium-magnesium phosphates by treating the suspension from raw brine purification with orthophosphoric acid (H(3)PO(4)), 2. production of precipitated chalk from soda processing waste, 3. production of gypsum and semi-brine, 4. desulphurisation of fume gases from the factory power plant, 5. utilization of distiller waste. The tests, accomplished on a laboratory scale, showed the high efficiency of these methods. Economic analysis has proved that only four out of the five presented processes can have a positive financial effect on soda ash factories, as well as being well justified economically. The value of two of the innovations presented is confirmed by their implementation in factories.

Absence of sodA Increases the Levels of Oxidation of Key Metabolic Determinants of Borrelia burgdorferi.

Directory of Open Access Journals (Sweden)

Maria D Esteve-Gassent

Full Text Available Borrelia burgdorferi, the causative agent of Lyme disease, alters its gene expression in response to environmental signals unique to its tick vector or vertebrate hosts. B. burgdorferi carries one superoxide dismutase gene (sodA capable of controlling intracellular superoxide levels. Previously, sodA was shown to be essential for infection of B. burgdorferi in the C3H/HeN model of Lyme disease. We employed two-dimensional electrophoresis (2-DE and immunoblot analysis with antibodies specific to carbonylated proteins to identify targets that were differentially oxidized in the soluble fractions of the sodA mutant compared to its isogenic parental control strain following treatment with an endogenous superoxide generator, methyl viologen (MV, paraquat. HPLC-ESI-MS/MS analysis of oxidized proteins revealed that several proteins of the glycolytic pathway (BB0057, BB0020, BB0348 exhibited increased carbonylation in the sodA mutant treated with MV. Levels of ATP and NAD/NADH were reduced in the sodA mutant compared with the parental strain following treatment with MV and could be attributed to increased levels of oxidation of proteins of the glycolytic pathway. In addition, a chaperone, HtpG (BB0560, and outer surface protein A (OspA, BBA15 were also observed to be oxidized in the sodA mutant. Immunoblot analysis revealed reduced levels of Outer surface protein C (OspC, Decorin binding protein A (DbpA, fibronectin binding protein (BBK32, RpoS and BosR in the sodA mutant compared to the control strains. Viable sodA mutant spirochetes could not be recovered from both gp91/phox-⁄- and iNOS deficient mice while borrelial DNA was detected in multiple tissues samples from infected mice at significantly lower levels compared to the parental strain. Taken together, these observations indicate that the increased oxidation of select borrelial determinants and reduced levels of critical pathogenesis-associated lipoproteins contribute to the in vivo deficit of

Effects of Palm Kernel Shell Ash on Lime-Stabilized Lateritic Soil

Science.gov (United States)

Nnochiri, Emeka Segun; Ogundipe, Olumide M.; Oluwatuyi, Opeyemi E.

2017-09-01

The research investigated the effects of palm kernel shell ash (PKSA) on lime-stabilized lateritic soil. Preliminary tests were performed on three soil samples, i.e., L1, L2 and L3 for identification; the results showed that L1 was A-7-6, L2 was A-7-6, and L3 was A-7-6. The optimum amount of lime for each of the soil samples was achieved. The optimum amount for L1 was 10%, for L2, 8% and for L3, 10%; at these values they recorded the lowest plasticity indexes. The further addition of PKSA was performed by varying the amount of PKSA and lime added to each of the soil samples. The addition of 4% PKSA+ 6% lime, the addition of 4% PKSA + 4% lime, and the addition of 4% PKSA + 6% lime increased the California Bearing Ratio (CBR) to the highest values for L1, L2 and L3 from 8.20%. It was concluded that PKSA can be a suitable complement for lime stabilization in lateritic soil.

Origin of C. latifolia and C. aurantiifolia triploid limes: the preferential disomic inheritance of doubled-diploid 'Mexican' lime is consistent with an interploid hybridization hypothesis.

Science.gov (United States)

Rouiss, H; Bakry, F; Froelicher, Y; Navarro, L; Aleza, P; Ollitrault, P

2018-03-05

Two main types of triploid limes are produced worldwide. The 'Tahiti' lime type (Citrus latifolia) is predominant, while the 'Tanepao' type (C. aurantiifolia) is produced to a lesser extent. Both types result from natural interspecific hybridization involving a diploid gamete of C. aurantiifolia 'Mexican' lime type (itself a direct interspecific C. micrantha × C. medica hybrid). The meiotic behaviour of a doubled-diploid 'Mexican' lime, the interspecific micrantha/medica recombination and the resulting diploid gamete structures were analysed to investigate the possibility that 'Tahiti' and 'Tanepao' varieties are derived from natural interploid hybridization. A population of 85 tetraploid hybrids was established between a doubled-diploid clementine and a doubled-diploid 'Mexican' lime and used to infer the genotypes of 'Mexican' lime diploid gametes. Meiotic behaviour was studied through combined segregation analysis of 35 simple sequenbce repeat (SSR) and single nucleotide polymorphismn (SNP) markers covering the nine citrus chromosomes and cytogenetic studies. It was supplemented by pollen viability assessment. Pollen viability of the doubled-diploid Mexican lime (64 %) was much higher than that of the diploid. On average, 65 % of the chromosomes paired as bivalents and 31.4 % as tetravalents. Parental heterozygosity restitution ranged from 83 to 99 %. Disomic inheritance with high preferential pairing values was deduced for three chromosomes. Intermediate inheritances, with disomic trend, were found for five chromosomes, and an intermediate inheritance was observed for one chromosome. The average effective interspecific recombination rate was low (1.2 cM Mb-1). The doubled-diploid 'Mexican' lime had predominantly disomic segregation, producing interspecific diploid gamete structures with high C. medica/C. micrantha heterozygosity, compatible with the phylogenomic structures of triploid C. latifolia and C. aurantiifolia varieties. This disomic trend limits

Elemental analysis of Taiwanese areca nut and limes with INAA

International Nuclear Information System (INIS)

Wei, Y.Y.; Chung, C.

1997-01-01

The popular areca nuts were sampled and their stuffed white and red lime were collected simultaneously from four marketplaces in Taiwan in different growing seasons. Samples of areca nut were treated via homogenizer prior to freeze drying, about 100-150 mg each of the areca nut and lime were packed into PE bag. Samples were irradiated with neutron flux about 10 12 n x cm -2 x s -1 . A total of 17, 18, and 13 elements was analyzed with INAA for white lime, red lime, and areca nut, respectively. The results indicated that Ca have the highest concentration in both limes. Most elements in collected samples have wide range of concentrations among different seasons and marketplaces. It is suggested that the elemental concentration of areca nut and limes exists in divergence originated from various farms in Taiwan. In addition, four elements of Ca, Fe, Mg, and Sc are probably overtaken by persons having chewing habit of areca nut and their effects on oral cancer are discussed. (author)

The association between state bans on soda only and adolescent substitution with other sugar-sweetened beverages: a cross-sectional study

OpenAIRE

Taber, Daniel R; Chriqui, Jamie F; Vuillaume, Renee; Kelder, Steven H; Chaloupka, Frank J

2015-01-01

Background: Across the United States, many states have actively banned the sale of soda in high schools, and evidence suggests that students’ in-school access to soda has declined as a result. However, schools may be substituting soda with other sugar-sweetened beverages (SSBs), and national trends indicate that adolescents are consuming more sports drinks and energy drinks. This study examined whether students consumed more non-soda SSBs in states that banned the sale of soda in school. Meth...

Economic evaluation of the industrial solar production of lime

International Nuclear Information System (INIS)

Meier, Anton; Gremaud, Nicolas; Steinfeld, Aldo

2005-01-01

The use of concentrated solar energy in place of fossil fuels for driving the endothermic calcination reaction CaCO 3 → CaO + CO 2 at above 1300 K has the potential of reducing CO 2 emissions by 20% in a state-of-the-art lime plant and up to 40% in a conventional cement plant. An economic assessment for an industrial solar calcination plant with 25 MW th solar input indicates that the cost of solar produced lime ranges between 128 and 157 $/t, about twice the current selling price of conventional lime. The solar production of high purity lime for special sectors in the chemical and pharmaceutical industry might be competitive with conventional fossil fuel based calcination processes at current fuel prices

Managing ecosystems without prior knowledge: pathological outcomes of lake liming

Directory of Open Access Journals (Sweden)

David G. Angeler

2017-12-01

Full Text Available Management actions often need to be taken in the absence of ecological information to mitigate the impact of pressing environmental problems. Managers counteracted the detrimental effects of cultural acidification on aquatic ecosystems during the industrial era using liming to salvage biodiversity and ecosystem services. However, historical contingencies, i.e., whether lakes were naturally acidic or degraded because of acidification, were largely unknown and therefore not accounted for in management. It is uncertain whether liming outcomes had a potentially detrimental effect on naturally acidic lakes. Evidence from paleolimnological reconstructions allowed us to analyze community structure in limed acidified and naturally acidic lakes, and acidified and circumneutral references. We analyzed community structure of phytoplankton, zooplankton, macroinvertebrates (littoral, sublittoral, profundal, and fish between 2000 and 2004. Naturally acidic limed lakes formed communities that were not representative of the other lake types. The occurrence of fish species relevant for ecosystem service provisioning (fisheries potential in naturally acidic limed lakes were confounded by biogeographical factors. In addition, sustained changes in water quality were conducive to harmful algal blooms. This highlights a pathological outcome of liming lakes when their naturally acidic conditions are not accounted for. Because liming is an important social-ecological system, sustained ecological change of lakes might incur undesired costs for societies in the long term.

Sugar-sweetened beverage, diet soda, and fatty liver disease in the Framingham Heart Study cohorts.

Science.gov (United States)

Ma, Jiantao; Fox, Caroline S; Jacques, Paul F; Speliotes, Elizabeth K; Hoffmann, Udo; Smith, Caren E; Saltzman, Edward; McKeown, Nicola M

2015-08-01

Non-alcoholic fatty liver disease affects ∼30% of US adults, yet the role of sugar-sweetened beverages and diet soda on these diseases remains unknown. We examined the cross-sectional association between intake of sugar-sweetened beverages or diet soda and fatty liver disease in participants of the Framingham Offspring and Third Generation cohorts. Fatty liver disease was defined using liver attenuation measurements generated from computed tomography in 2634 participants. Alanine transaminase concentration, a crude marker of fatty liver disease, was measured in 5908 participants. Sugar-sweetened beverage and diet soda intake were estimated using a food frequency questionnaire. Participants were categorized as either non-consumers or consumers (3 categories: 1 serving/month to sugar-sweetened beverages or diet soda. After adjustment for age, sex, smoking status, Framingham cohort, energy intake, alcohol, dietary fiber, fat (% energy), protein (% energy), diet soda intake, and body mass index, the odds ratios of fatty liver disease were 1, 1.16 (0.88, 1.54), 1.32 (0.93, 1.86), and 1.61 (1.04, 2.49) across sugar-sweetened beverage consumption categories (p trend=0.04). Sugar-sweetened beverage consumption was also positively associated with alanine transaminase levels (p trend=0.007). We observed no significant association between diet soda intake and measures of fatty liver disease. In conclusion, we observed that regular sugar-sweetened beverage consumption was associated with greater risk of fatty liver disease, particularly in overweight and obese individuals, whereas diet soda intake was not associated with measures of fatty liver disease. Copyright © 2015 European Association for the Study of the Liver. All rights reserved.

Water Utility Lime Sludge Reuse – An Environmental Sorbent ...

Science.gov (United States)

Lime sludge can be used as an environmental sorbent to remove sulfur dioxide (SO2) and acid gases, by the ultra-fine CaCO3 particles, and to sequester mercury and other heavy metals, by the Natural Organic Matter and residual activated carbon. The laboratory experimental set up included a simulated flue gas preparation unit, a lab-scale wet scrubber, and a mercury analyzer system. The influent mercury concentration was based on a range from 22 surveyed power plants. The reactivity of the lime sludge sample for acid neutralization was determined using a method similar to method ASTM C1318-95. Similar experiments were conducted using reagent calcium carbonate and calcium sulfate to obtain baseline data for comparing with the lime sludge test results. The project also evaluated the techno-economic feasibility and sustainable benefits of reusing lime softening sludge. If implemented on a large scale, this transformative approach for recycling waste materials from water treatment utilities at power generation utilities for environmental cleanup can save both water and power utilities millions of dollars. Huge amounts of lime sludge waste, generated from hundreds of water treatment utilities across the U.S., is currently disposed in landfills. This project evaluated a sustainable and economically-attractive approach to the use of lime sludge waste as a valuable resource for power generation utilities.

Effect of gamma radiation on chemical composition and storability of lime RTS

International Nuclear Information System (INIS)

Pandey, S.K.; Bisen, A.; Dwivedi, V.

2008-01-01

In the present investigation, the RTS was irradiated with different doses of gamma radiation to study their effect on chemical composition and storability of lime RTS and vitamin C content only was influenced significantly by 50 Gy gamma radiation during storage (16 days) without adversely affecting the quality of lime fruits, whereas, under control and higher doses of gamma radiation, the quality of lime RTS was deteriorated. The irradiation of lime with 50 Gy gamma radiation may be useful for extending storability of lime of RTS and stabilizing the market demand. (author)

Efficacy of baking soda-containing chewing gum in removing natural tooth stain.

Science.gov (United States)

Mankodi, S M; Conforti, N; Berkowitz, H

2001-07-01

A 14-week, double-blind, randomized clinical trial was conducted with 126 healthy volunteers to compare the efficacy of twice-daily use of 3 baking soda-containing chewing gums in removing natural tooth stain when used in conjunction with a program of regular oral hygiene. All 3 chewing gums significantly reduced extrinsic stain (P Baking Soda Gum (AHDC) reduced dental stain by 70.8%, compared to reductions of 71.9% and 65.3%, after use of 2 experimental gum formulations. Whitened appearance improved by 1.73 shade tabs using AHDC gum, and up to 2.49 shade tabs with the experimental formulations. These results suggest that the use of baking soda-containing gum after meals, in conjunction with good oral hygiene, can improve both extrinsic dental staining and the whitened appearance of teeth.

Effect of neutron irradiation on etching, optical and structural properties of microscopic glass slide used as a solid state nuclear track detector

International Nuclear Information System (INIS)

Singh, Surinder; Kaur Sandhu, Amanpreet; Prasher, Sangeeta; Prakash Pandey, Om

2007-01-01

Microscopic glass slides are soda-lime glasses which are readily available and are easy to manufacture with low production cost. The application of these glasses as nuclear track detector will help us to make use of these glasses as solid-state nuclear track detector. The present paper describes the variation in the etching, optical and structural properties of the soda-lime microscopic glass slides due to neutron irradiation of different fluences. The color transformation and an increase in the optical absorption with neutron irradiation are observed. Both the bulk and track etch rates are found to increase with neutron fluence, thus showing a similar dependence on neutron fluence, but the sensitivity remains almost constant

Natronobacillus azotifigens gen. nov., sp. nov., an anaerobic diazotrophic haloalkaliphile from soda-rich habitats

NARCIS (Netherlands)

Sorokin, I.D.; Zadorina, E.V.; Kravchenko, I.K.; Boulygina, E.S.; Tourova, T.P.; Sorokin, D.Y.

2009-01-01

Gram-positive bacteria capable of nitrogen fixation were obtained in microoxic enrichments from soda soils in south-western Siberia, north-eastern Mongolia, and the Lybian desert (Egypt). The same organisms were obtained in anoxic enrichments with glucose from soda lake sediments in the Kulunda

Lime utilization in the laboratory, field, and design of pavement layers : final report.

Science.gov (United States)

2017-01-01

The objective of this study was to review and report the best practices of using lime (i.e., granulated lime, hydrated lime, and slurry lime) to dry soil, in working tables, and in pavement applications. The project also reviewed and documented the i...

Analysis of caustic soda of different manufacturers in pakistan for mercerization of cotton textiles

International Nuclear Information System (INIS)

Zahid, B.; Faisal, S.; Siddique, S.H.

2017-01-01

Pakistan has sufficient production capacity of caustic soda to cater the needs of the local industry. Presently, Pakistan has four major plants with production capacity around 435,000 mega ton per year of caustic soda of various grades. Textile industry of Pakistan is the major consumer of produced high grade caustic soda; as the presence of any impurities especially dissolved salts and metals is unfavorable for wet processing of cotton. This study investigates the performance of three different local brands of caustic soda intended for use in textile wet processing of cotton fabric specifically for mercerization process. The brands were selected based on their purity grades. The selected caustic soda samples were chemically analyzed for the presence of impurities. Twenty seven cotton fabric samples (nine samples of each brand) were prepared by mercerization in slack state. The cotton fabric samples were tested for changes in surface morphology, tensile strength (warp and weft), tear strength, air permeability and K/S (Colour Strength). The results were analyzed using one-way ANOVA (Analysis of Variance) to ascertain the statistical equivalence within and between the tested brands. The results showed no significant differences across the tested brands at a 95% confidence level except for air permeability and K/S in blue shade. (author)

The association between state bans on soda only and adolescent substitution with other sugar-sweetened beverages: a cross-sectional study.

Science.gov (United States)

Taber, Daniel R; Chriqui, Jamie F; Vuillaume, Renee; Kelder, Steven H; Chaloupka, Frank J

2015-07-27

Across the United States, many states have actively banned the sale of soda in high schools, and evidence suggests that students' in-school access to soda has declined as a result. However, schools may be substituting soda with other sugar-sweetened beverages (SSBs), and national trends indicate that adolescents are consuming more sports drinks and energy drinks. This study examined whether students consumed more non-soda SSBs in states that banned the sale of soda in school. Student data on consumption of various SSBs and in-school access to vending machines that sold SSBs were obtained from the National Youth Physical Activity and Nutrition Study (NYPANS), conducted in 2010. Student data were linked to state laws regarding the sale of soda in school in 2010. Students were cross-classified based on their access to vending machines and whether their state banned soda in school, creating 4 comparison groups. Zero-inflated negative binomial models were used to compare these 4 groups with respect to students’ self-reported consumption of diet soda, sports drinks, energy drinks, coffee/tea, or other SSBs. Students who had access to vending machines in a state that did not ban soda were the reference group. Models were adjusted for race/ethnicity, sex, grade, home food access, state median income, and U.S. Census region. Students consumed more servings of sports drinks, energy drinks, coffee/tea, and other SSBs if they resided in a state that banned soda in school but attended a school with vending machines that sold other SSBs. Similar results were observed where schools did not have vending machines but the state allowed soda to be sold in school. Intake was generally not elevated where both states and schools limited SSB availability – i.e., states banned soda and schools did not have SSB vending machines. State laws that ban soda but allow other SSBs may lead students to substitute other non-soda SSBs. Additional longitudinal research is needed to confirm this

Effects of a Baking Soda Gum on extrinsic dental stain: results of a longitudinal 4-week assessment.

Science.gov (United States)

Soparkar, P; Newman, M B

2001-07-01

An evaluation of the effects of ARM & HAMMER DENTAL CARE The Baking Soda Gum (AHDC) on extrinsic dental stain was made in 48 subjects presenting with measurable extrinsic stain. The subjects were randomized to use either the baking soda gum or a non-baking soda placebo gum for 20 minutes twice daily after lunch and dinner while brushing once daily. The procedure of limited brushing was chosen to simulate the level of hygiene normally practiced by participants entering a clinical study. After 4 weeks, the reduction in measurable extrinsic stain in the baking soda gum group was statistically significant (P = .0044) relative to baseline. Statistical analysis of the placebo gum group revealed no significant change in extrinsic stain from baseline. The magnitude of the unadjusted longitudinal reduction in extrinsic stain in the baking soda gum group was 29.7% at 4 weeks.

Influence of lime juice on the severity of sickle cell anemia.

Science.gov (United States)

Adegoke, Samuel Ademola; Shehu, Umar Abdullahi; Mohammed, Lasisi Oluwafemi; Sanusi, Yunusa; Oyelami, Oyeku Akibu

2013-06-01

The pain in sickle cell anemia (SCA) is often triggered by dehydration, acidosis, and fever that are usually due to malaria. Intake of lime juice was recently demonstrated to facilitate clearance of the malaria parasite. It was therefore sought to determine whether regular intake of lime juice will ameliorate crisis, especially recurrent bone pain. In this preliminary, open-labeled, randomized study, the effects of lime juice on the clinical and some laboratory characteristics of children with SCA were tested. Among the 113 children with SCA studied in two hospitals, the 58 receiving lime treatment had lower rates of significant painful episodes than the 55 without lime (37 versus 83 crises in 6 months, and 0.64±0.11 versus 1.51±0.34 average rates per child, plime did not cause any significant side-effect. Regular intake of lime juice may be of great therapeutic and nutritional relevance in children with SCA.

Experimental study of silty clay stabilization with cement and lime in multan, pakistan

International Nuclear Information System (INIS)

Sultan, T.

2014-01-01

Stabilization is valuable substitute for advancing the soil characteristics. The engineering features gained after stabilization differs broadly owing to non-uniformity in constitutions of soil. This study describes an assessment of cement and lime additives for advancing soils ventures. The effectiveness of lime and cement stabilization on geotechnical characteristics of the in situ soil has also been described in the paper. The additives like cement and lime were added in different dosage rates to examine the change in properties of the in situ soil. Cement addition caused an increase in unconfined compression strength (UCS) throughout from 4% to 16% of cement. Moreover, it has been observed that by adding lime, the early strength of clay increases up to 6% of lime but for long term strength i.e. 28 days maximum strengths is achieved for 4% of lime. It also confirms that with more percentage of lime and longer duration of curing, it expands. In addition to the strength behavior of samples at various percentages of cement and lime, the deflection at failure point was also examined. In order to make a straight comparison, both cement and lime stabilized soils were also tested in laboratory. Generally, the performance of Portland cement-stabilized soils was advanced to lime in the experiments performed. (author)

Development of a three-dimensional CFD model for rotary lime kilns

Energy Technology Data Exchange (ETDEWEB)

Lixin Tao; Blom, Roger (FS Dynamics Sweden AB, Goeteborg (Sweden)); Nordgren, Daniel (Innventia, Stockholm (Sweden))

2010-11-15

In the calcium loop of the recovery cycle in a Kraft process of pulp and paper production, rotary lime kilns are used to convert the lime mud, mainly CaCO3, back to quick lime, CaO, for re-use in the causticizing process. The lime kilns are one of the major energy consumption devices for paper and pulp industry. Because of the rising oil price and new emission limits, the pulp mills have been forced to look for alternative fuels for their lime kilns. One interesting alternative to oil, often easily available at pulp mills, is biofuels such as sawdust and bark. However the practical kiln operation often encounters some difficulties because of the uncertainties around the biofuel impact on the lime kiln performance. A deeper understanding of the flame characteristics is required when shifting from oil to biofuels. Fortunately recent advances in modern Computational Fluid Dynamics, CFD, have provided the possibility to study and predict the detailed flame characteristics regarding the lime kiln performance. In this project a three-dimensional CFD model for rotary lime kilns has been developed. To simulate a rotary lime kiln the developed CFD model integrates the three essential sub-models, i.e. the freeboard hot flow model, the lime bed model and the rotating refractory wall model and it is developed based on the modern CFD package: FLUENT which is commercially available on the market. The numerical simulations using the developed CFD model have been performed for three selected kiln operations fired with three different fuel mixtures. The predicted results from the CFD modelling are presented and discussed in order to compare the impacts on the kiln performance due to the different firing conditions. During the development, the lime kiln at the Soedra Cell Moensteraas mill has been used as reference kiln. To validate the CFD model, in-plant measurements were carried out in the Moensteraas lime kiln during an experiment campaign. The results obtained from the

Hygroscopic slaking of lime with steam or humid air. New energy effective lime slaking technology in kraft pulping; Hygroskopisk slaeckning av kalk med aanga eller fuktig luft. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

Energy Technology Data Exchange (ETDEWEB)

Lundqvist, Roland

2005-12-15

Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional slaking method is that heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant. The forecasted method means that lime is slaked with steam or humid air, for example combined with a lime mud drier and a lime kiln. The task has included slaking of burned lime with steam or humid hot air, on purpose to test a specific machine equipment in pilote scale, and to investigate temperatures and hydratization rates able to reach. Also the lime slaked with steam/humid air should be compared with burned lime slaked in green liquor when green liquor is causticized, and to investigate the dewatering properties of formed lime mud. The target group is pulp and paper industry using the kraft process. The tests have been performed at SMA Svenska Mineral AB plant (lime burning) at Sandarne Sweden in years 2004-2005. Hydrated lime of varying slaking rates has been produced at temperatures up to 270 deg C. Caustizicing being performed show that dewatering properties of lime mud formed is quite up to the standard of lime mud from burned lime slaked in green liquor. The apprehension, that the hygroscopic slaked lime should result in lime mud difficult to dewater, has not become true. Important experiences have come out which could be used as a base in further investigations.

Effects of experimental acidification on mobilisation of metals from sediments of limed and non-limed lakes

International Nuclear Information System (INIS)

Waellstedt, Teresia; Borg, Hans

2003-01-01

In order to study the influence of pH on the mobilisation of metals from lake sediments, intact sediment cores with overlying water were sampled from one lime treated lake and one acidified lake. The overlying water of two cores from each lake was successively acidified to pH 4.2 over a period of 3 months. In the acid treated samples from the limed lake, the initial concentrations of Al, Cd, Mn, Pb and Zn in the overlying water were generally lower and the final concentrations were higher than in the acid treated samples from the acidified lake. The labile inorganic fraction of Al (Al i ) was increasingly dominating as pH decreased. Redox potential and pH in the sediment indicated that the upper two centimetres were involved in the exchange reactions. The experiment showed that mobilisation of metals from sediments can occur and the results indicated that mobilisation could contribute to increased concentrations of metals in lake water during reacidification of formerly lime treated lakes. - Reacidification leads to mobilisation of metals from lake sediments

Effects of Diet Soda on Gut Hormones in Youths With Diabetes

OpenAIRE

Brown, Rebecca J.; Walter, Mary; Rother, Kristina I.

2012-01-01

OBJECTIVE In patients with type 2 diabetes, but not type 1 diabetes, abnormal secretion of incretins in response to oral nutrients has been described. In healthy youths, we recently reported accentuated glucagon-like peptide 1 (GLP-1) secretion in response to a diet soda sweetened with sucralose and acesulfame-K. In this study, we examined the effect of diet soda on gut hormones in youths with diabetes. RESEARCH DESIGN AND METHODS Subjects aged 12?25 years with type 1 diabetes (n = 9) or type...

Conversion of Hanford salt cake to glass: laboratory studies

International Nuclear Information System (INIS)

Schulz, W.W.; Dressen, A.L.; Hobbick, C.W.; Kupfer, M.J.

1976-05-01

Approximately 140 million liters of solid salt cake (mainly NaNO 3 ), produced by evaporation of aged, alkaline high-level wastes, will be stored in underground tanks when the present Hanford Waste Management Program is completed in the early 1980's. These solid wastes can be converted to silicate-based glasses by melting them either at 1200 to 1300 0 C with appropriate amounts of sand and lime (soda-lime formulation) or at 1000 to 1100 0 C with appropriate amounts of Columbia River basalt and B 2 O 3 (basalt formulation). Both formulations yield dense, immobile glasses of low water leachability (10 -7 to 10 -6 g cm -2 day -1 ) suitable for terminal storage. The soda-lime formulation is presently preferred over the basalt formulation because it can accommodate more salt cake (50 wt percent versus 30 to 40 wt percent) while yielding a glass whose volume is 10 to 20 percent less than the volume of the salt cake in the melt charge

Long-Term Sustainability from the Perspective of Cullet Recycling in the Container Glass Industry: Evidence from Italy

Directory of Open Access Journals (Sweden)

Mario Testa

2017-10-01

Full Text Available Glass manufacturing is a high-volume process, during which large substance quantities are transformed into commercial products, and significant amounts of non-renewable resources and energy (i.e., thermal fuels and electrical power are consumed. The main purpose of this study is to give a critical explanation of the performance of the Italian container glass industry from the perspective of cullet being recycled, to outline the opportunities for transition towards circular business models that stimulate innovation in new sectors based on reverse-cycle activities for recycling. In 2015, disparate performances have been achieved as regards the container glass recycling rate in northern, central, and southern Italy, accounting for around 73%, 64%, and 55%, respectively. In fact, only northern Italy is in line with European targets, as by 2025 it will only need to increase its current performance by two percentage points, unlike central and southern Italy that will have to increase performance by, respectively, 11% and 20%. This shows a need to improve the efficiency of municipal waste collection systems in central and southern Italy, where undifferentiated waste still holds appreciable amounts of glass. Consequently, we propose several improvement channels, from the revision of waste legislation to the re-engineering of waste management supply chains.

Plasticity, Swell-Shrink, and Microstructure of Phosphogypsum Admixed Lime Stabilized Expansive Soil

Directory of Open Access Journals (Sweden)

Jijo James

2016-01-01

Full Text Available The study involved utilization of an industrial waste, Phosphogypsum (PG, as an additive to lime stabilization of an expansive soil. Three lime dosages, namely, initial consumption of lime (ICL, optimum lime content (OLC, and less than ICL (LICL, were identified for the soil under study for stabilizing the soil. Along with lime, varying doses of PG were added to the soil for stabilization. The effect of stabilization was studied by performing index tests, namely, liquid limit, plastic limit, shrinkage limit, and free swell test, on pulverized remains of failed unconfined compression test specimens. The samples were also subjected to a microstructural study by means of scanning electron microscope. Addition of PG to lime resulted in improvement in the plasticity and swell-shrink characteristics. The microstructural study revealed the formation of a dense compact mass of stabilized soil.

Kaffir lime leaves extract inhibits biofilm formation by Streptococcus mutans.

Science.gov (United States)

Kooltheat, Nateelak; Kamuthachad, Ludthawun; Anthapanya, Methinee; Samakchan, Natthapon; Sranujit, Rungnapa Pankla; Potup, Pachuen; Ferrante, Antonio; Usuwanthim, Kanchana

2016-04-01

Although kaffir lime has been reported to exhibit antioxidant and antileukemic activity, little is known about the antimicrobial effect of kaffir lime extract. Because Streptococcus mutans has been known to cause biofilm formation, it has been considered the most important causative pathogen of dental caries. Thus, the effective control of its effects on the oral biofilm is the key to the prevention of dental caries. The aims of the present study were to investigate the effect of kaffir lime leaves extract on biofilm formation and its antibacterial activity on S. mutans. We examined the effect of kaffir lime leaves extract on growth and biofilm formation of S. mutans. For the investigation we used a kaffir lime extract with high phenolic content. The minimum inhibitory concentration of the extract was determined by broth microdilution assay. The inhibitory effect of the test substances on biofilm formation was also investigated by biofilm formation assay and qRT-PCR of biofilm formation-associated genes. Kaffir lime leaves extract inhibits the growth of S. mutans, corresponding to the activity of an antibiotic, ampicillin. Formation of biofilm by S. mutans was also inhibited by the extract. These results were confirmed by the down-regulation of genes associated with the biofilm formation. The findings highlight the ability of kaffir lime leaves extract to inhibit S. mutans activity, which may be beneficial in the prevention of biofilm formation on dental surface, reducing dental plaque and decreasing the chance of dental carries. Copyright © 2016 Elsevier Inc. All rights reserved.

Liming the acid lake Hovvatn, Norway: a whole-ecosystem study

Energy Technology Data Exchange (ETDEWEB)

Raddum, G G; Brettum, P; Matzow, D; Nilssen, J P; Skov, A; Sveaelv, T; Wright, R F

1986-12-01

Hovvatn, a 1 sq. km. chronically-acidified lake in southernmost Norway, was treated with 200 tonne of powdered limestone in March 1981. An additional 40 tonne were added to a 0.046 sq km pond (Pollen) draining into Hovvatn. The lakes were stocked with brown trout in June 1981 and in each subsequent year. At ice-out pH rose from 4.4 to 6.3 (Hovvatn) and 7.5 (Pollen), Ca and alkalinity increased, and total Al decreased by 120 ..mu..g/l. None of the other major ions exhibited significant changes in concentration. Total organic C and P increased after liming. The phytoplankton community was dominated by chrysophytes and did not change significantly following liming. The zooplankton community was typical of acid lakes prior to liming. There was a clear succession in species dominance following treatment, although no new species immigrated to the lakes. Zoobenthos changed from a community characterized by low abundance and reduced number of species to increased abundance of oligochaetes, mayflies and chironomids. Hovvatn and Pollen were barren of fish prior to stocking. The stocked fish showed remarkably high growth rate during the first years. Liming apparently improved conditions for zoobenthos, enhancing the processing of fine detritus which in turn resulted in elevated levels of TOC and P in the lakewaters during the first year after liming. The oligotrophication process typical of acid lakes was temporarily reversed by liming. The interactions between groups of organisms in Hovvatn and Pollen indicates that many years are required before a new steady-state can be attained following liming. 61 references.

Beverages obtained from soda fountain machines in the U.S. contain microorganisms, including coliform bacteria.

Science.gov (United States)

White, Amy S; Godard, Renee D; Belling, Carolyn; Kasza, Victoria; Beach, Rebecca L

2010-01-31

Ninety beverages of three types (sugar sodas, diet sodas and water) were obtained from 20 self-service and 10 personnel-dispensed soda fountains, analyzed for microbial contamination, and evaluated with respect to U.S. drinking water regulations. A follow-up study compared the concentration and composition of microbial populations in 27 beverages collected from 9 soda fountain machines in the morning as well as in the afternoon. Ice dispensed from these machines was also examined for microbial contamination. While none of the ice samples exceeded U.S. drinking water standards, coliform bacteria was detected in 48% of the beverages and 20% had a heterotrophic plate count greater than 500cfu/ml. Statistical analyses revealed no difference in levels of microbial contamination between beverage types or between those dispensed from self-service and personnel-dispensed soda fountains. More than 11% of the beverages analyzed contained Escherichia coli and over 17% contained Chryseobacterium meningosepticum. Other opportunistic pathogenic microorganisms isolated from the beverages included species of Klebsiella, Staphylococcus, Stenotrophomonas, Candida, and Serratia. Most of the identified bacteria showed resistance to one or more of the 11 antibiotics tested. These findings suggest that soda fountain machines may harbor persistent communities of potentially pathogenic microorganisms which may contribute to episodic gastric distress in the general population and could pose a more significant health risk to immunocompromised individuals. These findings have important public health implications and signal the need for regulations enforcing hygienic practices associated with these beverage dispensers. Copyright 2009 Elsevier B.V. All rights reserved.

Hygroscopic slaking of lime with steam or humid air. New energy effective lime slaking technology in kraft pulping; Hygroskopisk slaeckning av kalk med aanga eller fuktig luft. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

Energy Technology Data Exchange (ETDEWEB)

Lundqvist, Roland

2003-07-15

Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional slaking method is that heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant. The forecasted method means that lime is slaked with steam or humid air, for example combined with a lime mud drier and a lime kiln. The task has included slaking of burned lime with steam or humid hot air, on purpose to test a specific machine equipment in pilote scale, and to investigate temperatures and hydratization rates able to reach. Also the lime slaked with steam/humid air should be compared with burned lime slaked in green liquor when green liquor is causticized, and to investigate the dewatering properties of formed lime mud. The target group is pulp and paper industry using the kraft process. The tests have been performed at SMA Svenska Mineral AB plant (lime burning) at Sandarne Sweden in years 2004-2005. Project owner has been the Swedish company Torkapparater AB, and the project is performed inside the 'Vaermeforsk Program for Pulp and Paper Industry 2004-2005'. Other partners, besides SMA Svenska Mineral AB, has been Stora Enso Skoghalls Bruk, Carnot AB, AaF Process AB and KTH Energiprocesser. Hydrated lime of varying slaking rates has been produced at temperatures up to 270 deg C. Caustizicing being performed show that dewatering properties of lime mud formed is quite up to the standard of lime mud from burned lime slaked in green liquor. The apprehension, that the hygroscopic slaked lime should result

Steam slaking of lime - kinetics and technology. New energy effective lime slaking technology in kraft pulping; Aangslaeckning av kalk - kinetik och teknik. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

Energy Technology Data Exchange (ETDEWEB)

Lundqvist, Roland

2008-06-15

Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional lime burning and slaking methods are that heat recovery is bad and heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant, and to recover heat at higher temperatures. The forecasted method means that lime is slaked with water vapour, for example combined with an indirect heated lime mud drier and a lime kiln. This project is a follow-up to pilot tests performed in a specific machine equipment at year 2006. The target group is pulp and paper industry using the kraft process. The owner of this new project is Carnot AB and the project is performed inside the Vaermeforsk Program for Pulp and Paper Industry 2006-2008. Partners and advisers in project group have been KTH Energy Processes, CTH Energy and Environment, LTH Chemical Technology, SMA Mineral AB, and reference group from STORA Enso Skoghall, Sodra Cell, M-Real Husum and SCA Packaging Piteaa. The task in this stage has included market investigations and laboratory tests. Contacts have been made with suppliers, preliminary dimensioning of process equipment and budget offers are received. Economic calculations have been made out of the offers. The laboratory tests are done as an examination paper at KTH Energiprocesser on the reactivity of burned lime from kraft lime kiln when it is slaked with water vapour instead of green liquor. The vapour intended to be used is at atmospheric pressure or even down to 0,2 atm. Complementary addition to these laboratory

Acid-base properties of a limed pyritic overburden during simulated weathering

Energy Technology Data Exchange (ETDEWEB)

Doolittle, J.J.; Hossner, L.R. [South Dakota State University, Brookings, SD (United States). Plant Science Dept.

1997-11-01

Surface-mine reclamation is often hindered by the formation of acid mine soil and acid mine drainage from FeS{sub 2} oxidation. Surface soils containing FeS{sub 2} are often treated with crushed limestone (predominately CaCO{sub 3}) to prevent aid minesoil formation. The main objective of this study was to evaluate the long-term effectiveness of liming pyritic minesoil to prevent the formation of acid minesoil and acid mine drainage. Pyritic minesoils that did not receive lime became acidic very rapidly and produced acidic leachate. Almost all of the FeS{sub 2} in this treatment oxidized during the first 200 d. The addition of lime at a rate of 25% of the theoretical acid-base account (ABA) significantly slowed FeS{sub 2} oxidation, but rapid oxidation ensued after the added lime was neutralized. Treatments receiving a liming rate of 50% ABA or greater remained neutral to alkaline throughout the study. Acid-base values and residual FeS{sub 2}-CO{sub 3} data, however, indicate that the lime was dissolving from the system faster than the FeS{sub 2} was oxidizing, and all the treatments would eventually become acidic. The results indicate that the liming of a pyritic overburden to an ABA of 125% is not a sustainable solution to preventing acid minesoil and acid mine drainage. 25 refs., 6 figs., 3 tabs.

Stabilization of expansive soil using bagasse ash & lime | Wubshet ...

African Journals Online (AJOL)

7-5 soil on the AASHTO classification was stabilized using 3% lime, 15% bagasse ash and 15% bagasse ash in combination with 3% lime by dry weight of the soil. The effect of the additives on the soil was investigated with respect to plastcity, ...

Where there's a will: can highlighting future youth-targeted marketing increase support for soda taxes?

Science.gov (United States)

Roh, Sungjong; Schuldt, Jonathon P

2014-12-01

Amid concern about high rates of obesity and related diseases, the marketing of nutritionally poor foods to young people by the food industry has come under heavy criticism by public health advocates, who cite decades of youth-targeted marketing in arguing for reforms. In light of recent evidence that the same event evokes stronger emotional reactions when it occurs in the future versus the past, highlighting youth-targeted marketing that has yet to occur may evoke stronger reactions to such practices, and perhaps, greater support for related health policy initiatives. In a between-subjects experiment, Web participants (N = 285) read that a major soda company had already launched (past condition) or was planning to launch (future condition) an advertising campaign targeting children. Measures included support for a soda tax and affective responses to the company's actions. Greater support for the soda tax was observed in the future condition than in the past condition. Moreover, participants in the future condition reported heightened negative emotions about the company's actions, which mediated the observed effect on soda tax support. The same action undertaken by the food industry (here, marketing soda to children) may evoke stronger negative emotions and greater support for a health policy initiative when it is framed prospectively rather than retrospectively.

Removal of Strontium from Drinking Water by Conventional ...

Science.gov (United States)

The United States Environmental Protection Agency Contaminant Candidate List 3 lists strontium as a contaminant for potential regulatory consideration in drinking water. There is very little data available on strontium removal from drinking water. As a result, there is an immediate need to perform treatment studies. The objective of this work is to evaluate the effectiveness of conventional and lime-soda ash softening treatments to remove strontium from surface and ground waters. Conventional drinking water treatment with aluminum and iron coagulants were able to achieve 12% and 5.9% strontium removal at best, while lime softening removed as much as 78% from natural strontium-containing ground water. Systematic fundamental experiments showed that strontium removal during the lime-soda ash softening was related to pH, calcium concentration and dissolved inorganic carbon concentration. Final strontium concentration was also directly associated with initial strontium concentration. Precipitated solids showed well-formed crystals or agglomerates of mixed solids, two polymorphs of calcium carbonate (vaterite and calcite), and strontianite, depending on initial water quality conditions. X-ray diffraction analysis suggested that strontium likely replaced calcium inside the crystal lattice and was likely mainly responsible for removal during lime softening. To inform the public.

Activated charcoal and baking soda to reduce odor associated with extensive blistering disorders.

Science.gov (United States)

Chakravarthi, Arun; Srinivas, C R; Mathew, Anil C

2008-01-01

Skin disease leading to extensive blistering and loss of skin is associated with a characteristic smell. Odor can cause physiologic disturbances such as increase in heart rate and respiratory rate. It can also cause nausea and vomiting and is disturbing to bystanders. To test odor reducing capability of activated charcoal. In this blinded experimental study we used putrefied amniotic membrane to produce odor and studied the effectiveness of activated charcoal and soda-bi-carbonate to reduce odor. Statistical analysis with Kruskal Wall's Chi Square Test and Man Whitney U test showed significant reduction of odor using activated charcoal by itself or along with soda-bi-carbonate. We recommend the usage of activated charcoal with/without soda bicarbonate as an inexpensive practical measure to reduce foul odor associated with extensive skin loss.

Soil Stabilization with Lime for the Construction of Forest Roads

Directory of Open Access Journals (Sweden)

Reginaldo Sérgio Pereira

2018-02-01

Full Text Available ABSTRACT The mechanical performance of soil stabilization using lime to improve forest roads was assessed. This study was conducted with lateritic soil (LVAd30 using lime content of 2% in the municipality of Niquelândia, Goiás state, Brazil. Geotechnical tests of soil characterization, compaction, and mechanical strength were performed applying different compaction efforts and curing periods. The results showed that lime content significantly changed the mechanical performance of natural soil, increasing its mechanical strength and load-carrying capacity. Compaction effort and curing time provided different responses in the unconfined compressive strength (UCS and California Bearing Ratio (CBR tests. The best UCS value (786.59 kPa for the soil-lime mixture was achieved with modified compaction effort and curing time of 28 days. In the CBR test, soil-lime mixtures compacted at intermediate and modified efforts and cured for 28 days were considered for application as subbase material of flexible road pavements, being a promising alternative for use in layers of forest roads.

LIME EFFECTIVENESS OF SOME FERTILIZERS IN A TROPICAL ACID ALFISOL

Directory of Open Access Journals (Sweden)

Mercy Omogbohu Anetor

2007-11-01

Full Text Available Liming increases production costs and environmentally unfriendly. Effectiveness of crystalliser (CRYS, single super phosphate (SSP and organic fertilizer (OF for liming was evaluated by determining pH and phosphorus- (P- availability in an acid alfisol incubated with the amendments, Ca(OH2 being reference. Treatments were replicated thrice in completely randomised design. Un-amended soil remained acidic (pH 4.8 but liming raised pH (6.1-6.6, enhancing maximum (15.09-17.33 mg kg-1 P–release (un-amended having 4.24-7.09 mg P kg-1. Lime (L and L+P treatments resulted in maximum pH increases (7.0-7.2, decreasing with incubation. Fertilizer treatments also raised pH (5.0-5.5 for OF, CRYS or SSP; 5.6-5.8 for CRYS +SSP, CRYS+OF and OF+SSP relative to control (5.2. Acid soil infertility-ameliorating potential of CRYS and OF was revealed. They could be used multi-purposely as lime and P fertilizers by poor-resource farmers challenged by acid soil infertility factors.

Lime treatment of liquid waste containing heavy metals, radionuclides and organics

International Nuclear Information System (INIS)

DuPont, A.

1990-01-01

This paper reports on lime treatment of liquid waste containing heavy metals, radio nuclides and organics. Lime is wellknown for its use in softening drinking water the treatment of municipal wastewaters. It is becoming important in the treatment of industrial wastewater and liquid inorganic hazardous waste; however, there are many questions regarding the use of lime for the treatment of liquid hazardous waste

[Effects of Lime on Seedling Growth,Yield and Volatile Constituents of Atractylodes lancea].

Science.gov (United States)

Zhang, Yan; Miki, Sakurai; Chen, Mei-lan; Takeda, Xiuji; Zhao, Dong-yue; Kang, Li-ping; Guo, Lan-ping

2015-03-01

To investigate the effects of different amounts of lime on yield and quality of Atractylodes lancea, and to provide reference for the herb growing site soil improvement and self-poisoning ease. Add different gradients of lime, and then measure their growth targets, yield and four kinds of volatile constituents content(hinesol, atractylone, β-eudesmol and atractylodin). Volatile constituents yield per plant was calculated. Adding 160 g/m2 lime had a significant role in promoting the growth and yield of herb; Adding 80 g/m2 lime was conducive to the volatile constituents production, and adding lime decreased the atractylone and atractylodin content, while increased the hinesol and β-eudesmol content; Adding 160 g/m2 lime promoted the volatile constituents yield per plant. Adding lime plays a role of neutralize soil pH, antibacteria and prevention incognita, and has a certain degree of ease autotoxicity and obstacle,and then promotes the yield and volatile constituents production of Atractylodes lancea.

Lime helps establish crownvetch on coal-breaker refuse

Science.gov (United States)

Miroslaw M. Czapowskyj; Edward A. Sowa

1976-01-01

A study was begun in 1965 to determine the effect of lime fertilizer, and mulch on the establishment and growth of crownvetch crowns planted on anthracite coal-breaker refuse. After 7 years the lime application had by far the strongest effect. Both 2.5 and 5.0 tons per acre increased survival and ground cover manyfold, and both treatments were equally beneficial from...

Extracting solid carbonaceous materials with solvents

Energy Technology Data Exchange (ETDEWEB)

1936-02-08

Solvent extraction of solid carbonaceous materials is performed in the presence of powdered catalysts together with alkaline substances. Oxides of nickel or iron or nickel nitrate have been used together with caustic soda or potash solutions or milk of lime. Solvents used include benzenes, middle oils, tars, tetrahydronaphthalene. The extraction is performed at 200 to 500/sup 0/C under pressures of 20 to 200 atm. Finely ground peat was dried and mixed with milk of lime and nickel nitrate and an equal quantity of middle oil. The mixture was heated for 3 h at 380/sup 0/C at 90 atm. 88.5% of the peat was extracted. In a similar treatment brown coal was impregnated with solutions of caustic soda and ferric chloride.

Models for predicting the mass of lime fruits by some engineering properties.

Science.gov (United States)

Miraei Ashtiani, Seyed-Hassan; Baradaran Motie, Jalal; Emadi, Bagher; Aghkhani, Mohammad-Hosein

2014-11-01

Grading fruits based on mass is important in packaging and reduces the waste, also increases the marketing value of agricultural produce. The aim of this study was mass modeling of two major cultivars of Iranian limes based on engineering attributes. Models were classified into three: 1-Single and multiple variable regressions of lime mass and dimensional characteristics. 2-Single and multiple variable regressions of lime mass and projected areas. 3-Single regression of lime mass based on its actual volume and calculated volume assumed as ellipsoid and prolate spheroid shapes. All properties considered in the current study were found to be statistically significant (ρ lime based on minor diameter and first projected area are the most appropriate models in the first and the second classifications, respectively. In third classification, the best model was obtained on the basis of the prolate spheroid volume. It was finally concluded that the suitable grading system of lime mass is based on prolate spheroid volume.

Characterization of historic lime mortars by neutron scattering and mercury porosimetry

International Nuclear Information System (INIS)

Zouridakis, N.; Stefanopoulos, K.L.; Treimer, W.

1999-01-01

Complete text of publication follows. Lime mortars were commonly used in building from ancient Greek times through to the beginning of the nineteenth century [1]. In the past few years, the increased interest in conservation and restoration of historic monuments requires a better knowledge of the structure and composition of lime mortars resulting from the various additives, as well as the preparation technique each time used. Lime mortars from ancient Greek monuments have been dated by using the radiocarbon method [2]. Furthermore, a wide selection of lime mortars from known historic periods and monuments in Greece has been examined by mercury porosimetry. It was found that their structure depends on the utilization of the monument which come from. In specific, lime mortars coming from residences have more or less the same structure, whereas the preparation technique differs for lime mortars coming from tombs and walls. The weathering effects on the porous system of the mortars are studied by neutron scattering. (author) [1] Brown, P.W., and Clifton, J.R., 'Air pollution and conservation', eds. J. Roswall and S. Aleby, 225 (1988), Elsevier, Amsterdam.; [2] N. Zouridakis, J.F. Sliege, A. Person et al., Archaeometry, 60 (1987) 29

Sugary soda consumption and albuminuria: results from the National Health and Nutrition Examination Survey, 1999-2004.

Directory of Open Access Journals (Sweden)

David A Shoham

Full Text Available BACKGROUND: End-stage renal disease rates rose following widespread introduction of high fructose corn syrup in the American diet, supporting speculation that fructose harms the kidney. Sugar-sweetened soda is a primary source of fructose. We therefore hypothesized that sugary soda consumption was associated with albuminuria, a sensitive marker for kidney disease. METHODOLOGY/PRINCIPAL FINDINGS: Design was a cross-sectional analysis. Data were drawn from the National Health and Nutrition Examination Survey (NHANES, 1999-2004. The setting was a representative United States population sample. Participants included adults 20 years and older with no history of diabetes mellitus (n = 12,601; after exclusions for missing outcome and covariate information (n = 3,243, the analysis dataset consisted of 9,358 subjects. Exposure was consumption of two or more sugary soft drinks, based on 24-hour dietary recall. The main outcome measure was Albuminuria, defined by albumin to creatinine ratio cutpoints of >17 mg/g (males and >25 mg/g (females. Logistic regression adjusted for confounders (diet soda, age, race-ethnicity, gender, poverty. Interactions between age, race-ethnicity, gender, and overweight-obesity were explored. Further analysis adjusted for potential mediators: energy intake, basal metabolic rate, obesity, hypertension, lipids, serum uric acid, smoking, energy expenditure, and glycohemoglobin. Alternative soda intake definitions and cola consumption were employed. RESULTS: Weighted albuminuria prevalence was 11%, and 17% consumed 2+ sugary soft drinks/day. The confounder-adjusted odds ratio for sugary soda was 1.40 (95% confidence interval: 1.13, 1.74. Associations were modified by gender (p = 0.008 and overweight-obesity (p = 0.014. Among women, the OR was 1.86 (95% CI: 1.37, 2.53; the OR among males was not significant. In the group with body mass under 25 kg/m(2, OR = 2.15 (95% confidence interval: 1.42, 3.25. Adjustment for potential

Suitability of a lime source high in manganese as a feed ingredient ...

African Journals Online (AJOL)

plasma enzyme levels, mineral concentrations in plasma, faeces and kidneys, mineral content of livers, haematology, hislopathol- ogy of livers and kidneys and bone measurements.It is concluded that the Ouplaas lime, .... Table 1 Mineral composition of the pure lime sources (dry basis). Lime sources. Na. (vo). Mg. (vo). K.

Phylogenetic origin of limes and lemons revealed by cytoplasmic and nuclear markers.

Science.gov (United States)

Curk, Franck; Ollitrault, Frédérique; Garcia-Lor, Andres; Luro, François; Navarro, Luis; Ollitrault, Patrick

2016-04-01

The origin of limes and lemons has been a source of conflicting taxonomic opinions. Biochemical studies, numerical taxonomy and recent molecular studies suggested that cultivated Citrus species result from interspecific hybridization between four basic taxa (C. reticulata,C. maxima,C. medica and C. micrantha). However, the origin of most lemons and limes remains controversial or unknown. The aim of this study was to perform extended analyses of the diversity, genetic structure and origin of limes and lemons. The study was based on 133 Citrus accessions. It combined maternal phylogeny studies based on mitochondrial and chloroplastic markers, and nuclear structure analysis based on the evaluation of ploidy level and the use of 123 markers, including 73 basic taxa diagnostic single nucleotide polymorphism (SNP) and indel markers. The lime and lemon horticultural group appears to be highly polymorphic, with diploid, triploid and tetraploid varieties, and to result from many independent reticulation events which defined the sub-groups. Maternal phylogeny involves four cytoplasmic types out of the six encountered in the Citrus genus. All lime and lemon accessions were highly heterozygous, with interspecific admixture of two, three and even the four ancestral taxa genomes. Molecular polymorphism between varieties of the same sub-group was very low. Citrus medica contributed to all limes and lemons and was the direct male parent for the main sub-groups in combination with C. micrantha or close papeda species (for C. aurata, C. excelsa, C. macrophylla and C. aurantifolia--'Mexican' lime types of Tanaka's taxa), C. reticulata(for C. limonia, C. karna and C. jambhiri varieties of Tanaka's taxa, including popular citrus rootstocks such as 'Rangpur' lime, 'Volkamer' and 'Rough' lemons), C. aurantium (for C. limetta and C. limon--yellow lemon types--varieties of Tanaka's taxa) or the C. maxima × C. reticulate hybrid (for C. limettioides--'Palestine sweet' lime types--and C

Liming of acid tropical soils: practice, prospects and constraints ...

African Journals Online (AJOL)

But the incidental inclusion of liming materials in fertilizers has not been effective and sustainable due to the intensive land use activities, constant application of acid-forming chemical fertilizers, leaching losses of bases and crop removal. Liming materials themselves vary in their calcium and magnesium contents and ...

Incorporation of turmeric-lime mixture during the preparation of ...

African Journals Online (AJOL)

GREGO

2007-03-19

Mar 19, 2007 ... behaviour) of 2 min-blanched samples (both treated and control) were the maximum among other corresponding puree samples. Thus, 2 min blanching time may be preferred for the preparation of this new type of turmeric-lime treated tomato puree product. Key words: Turmeric-lime, Lycopersicon ...

PERBEDAAN PH SALIVA ANTARA PENGGUNA PASTA GIGI YANG MENGANDUNG BAKING SODA DAN PENGGUNA PASTA GIGI YANG MENGANDUNG FLUOR

OpenAIRE

LINARDI, ALICIA NADIA

2014-01-01

2014 Latar belakang : Baking soda dan fluor merupakan bahan yang biasa ditambahkan dalam pasta gigi. Baking soda dan fluor mempunyai kemampuan untuk meningkatkan sekresi saliva dan pH saliva. Tujuan penelitian ini adalah untuk mengetahui perbedaan pH saliva antara pengguna pasta gigi yang mengandung baking soda dan pengguna pasta gigi yang mengandun fluor. Bahan dan metode : Jenis penelitian ini adalah eksperimental dengan desai...

Baking soda misuse as a home remedy: case experience of the California Poison Control System.

Science.gov (United States)

Al-Abri, S A; Kearney, T

2014-02-01

Baking soda is a common household product promoted by the manufacturer as an antacid. It contains sodium bicarbonate and has the potential for significant toxicity when ingested in excessive amounts. Characterizing the patterns and outcomes from the misuse of baking soda as a home remedy can guide the clinical assessment and preventative counselling of patients at risk for use of this product. We conducted a retrospective review of all symptomatic cases involving ingestion and misuse of a baking soda powder product that were reported to the California Poison Control System between the years 2000 and 2012. Of the 192 cases we identified, 55·8% were female, ages ranged 2 months to 79 years, and the most common reasons for misuse included antacid (60·4%), 'beat a urine drug test' (11·5%) and treat a UTI (4·7%). Most cases (55·2%) had significant symptoms warranting a medical evaluation, whereas 12 patients required hospital admission developed either electrolyte imbalances, metabolic alkalosis or respiratory depression. Misuse of baking soda can result in serious electrolyte and acid/base imbalances. Patients at highest risk of toxicity may include those who chronically use an antacid, those who use the method to 'beat' urine drug screens, pregnant women and young children. Self-treatment with baking soda as a home remedy may also mask or delay medical care thereby complicating or exacerbating an existing medical problem. We suggest that healthcare providers counsel high-risk patients about the potential complications of misuse of baking soda as a home remedy. © 2013 John Wiley & Sons Ltd.

40 CFR 180.1231 - Lime; exemption from the requirement of a tolerance.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Lime; exemption from the requirement... From Tolerances § 180.1231 Lime; exemption from the requirement of a tolerance. An exemption from the requirement of a tolerance is established for residues of lime. [70 FR 33363, June 8, 2005] ...

Lime-Stabilized Black Cotton Soil and Brick Powder Mixture as Subbase Material

Directory of Open Access Journals (Sweden)

S. Srikanth Reddy

2018-01-01

Full Text Available Various researchers, for the past few decades, had tried to stabilize black cotton soil using lime for improving its shrinkage and swelling characteristics. But these days, the cost of lime has increased resulting in increase in need for alternative and cost effective waste materials such as fly ash and rice husk ash. Brick powder, one among the alternative materials, is a fine powdered waste that contains higher proportions of silica and is found near brick kilns in rural areas. The objective of the study is to investigate the use of lime-stabilized black cotton soil and brick powder mixture as subbase material in flexible pavements. Black cotton soil procured from the local area, tested for suitability as subbase material, turned out to be unsuitable as it resulted in very less CBR value. Even lime stabilization of black cotton soil under study has not showed up the required CBR value specified for the subbase material of flexible pavement by MORTH. Hence the lime-stabilized black cotton soil is proportioned with brick powder to obtain optimum mixture that yields a better CBR value. The mixture of 20% brick powder and 80% lime-stabilized black cotton soil under study resulted in increase in the CBR value by about 135% in comparison with lime-stabilized black cotton soil. Thus it is promising to use the mixture of brick powder and lime-stabilized black cotton soil as subbase material in flexible pavements.

New waste based clinkers: Belite and lime formulations

International Nuclear Information System (INIS)

Raupp-Pereira, Fabiano; Ball, Richard James; Rocha, Joao; Labrincha, Joao A.; Allen, Geoffrey C.

2008-01-01

This work describes the formulation of new belite-based (CR2) and lime-based (CR3) cementitious materials derived from industrial wastes, such as sludges (generated in the Al-anodising and surface coating industrial processes, potable water filtration/cleaning operations and in marble sawing processes) and foundry sand. Powder mixtures were prepared and fired at different temperatures. For comparison, similar formulations were prepared with pre-treated and commercially available natural raw materials and processed in similar conditions. The thermal process was followed by differential scanning calorimetry (DSC) and high-temperature powder X-ray diffraction (HT-XRD) studies. The CR2 clinker was found to contain belite as the main cementitious phase, the main polymorph being identified by NMR. The CR3 clinker contained common cementitious phases, such as C 3 A and C 3 S, but free lime and calcium aluminium oxide sulphates were also identified by high temperature XRD and NMR. Then the corresponding cement was prepared and the evolution of the mechanical strength with time was evaluated. The lime-based cement obtained from wastes shows a stronger hardening character than the standard material, which tends to show dusting phenomena due to the presence of a reasonable amount of free lime (as the result of its expansive reaction with ambient moisture). Some fluxing impurities (e.g. alkalis) present in the waste materials improve the overall reactivity of the mixture and induces the combination of the lime in CR3. Raman, XPS and FIB techniques were used to fully characterise the aged cements

Activated charcoal and baking soda to reduce odor associated with extensive blistering disorders

Directory of Open Access Journals (Sweden)

Chakravarthi Arun

2008-01-01

Full Text Available Background: Skin disease leading to extensive blistering and loss of skin is associated with a characteristic smell. Odor can cause physiologic disturbances such as increase in heart rate and respiratory rate. It can also cause nausea and vomiting and is disturbing to bystanders. Aims: To test odor reducing capability of activated charcoal. Methods: In this blinded experimental study we used putrefied amniotic membrane to produce odor and studied the effectiveness of activated charcoal and soda-bi-carbonate to reduce odor. Results: Statistical analysis with Kruskal Wall′s Chi Square Test and Man Whitney U test showed significant reduction of odor using activated charcoal by itself or along with soda-bi-carbonate. Conclusion: We recommend the usage of activated charcoal with/without soda bicarbonate as an inexpensive practical measure to reduce foul odor associated with extensive skin loss.

Hypernatremia and metabolic alkalosis as a consequence of the therapeutic misuse of baking soda.

Science.gov (United States)

Fuchs, S; Listernick, R

1987-12-01

When used appropriately, baking soda (sodium bicarbonate, USP) is a nontoxic, readily available, multipurpose product found in many households. We report an infant who presented with hypernatremia and metabolic alkalosis due to the addition of baking soda to her water. This case represents the possible dangerous use of a common household product in infants owing to the lack of proper warning labels.

The Strength Behaviour of Lime Stabilized Organic Clay Soil Modified by Catalyst Additeives

Directory of Open Access Journals (Sweden)

Khitam Abdulhussein Saeed

2016-12-01

Full Text Available The organic clay soil can be found in many large size reclaimed lands. These soils present enormously high settlement potential and low strength that needs to be improved by means of effective ground improvement techniques. One of the low cost techniques is to modify the soil with lime in-situ to make it suitable for construction and allow it to increase in strength by pozzolanic reactions between lime and clay minerals. Lime is known to be an effective stabilization material for clayey soil. Nevertheless, its effectiveness may be less with organic clay due to low effective strength properties. Thus, this study concerns the addition of catalyst i.e. zeolite which may improve the performance of lime stabilization to accelerate lime-organic clay reactions. The unconfined compressive test (UCT is conducted on remoulded samples (38mm x 80mm for 0, 7, 14 , 28, and 90 days of curing period. The addition of synthetic zeolite in lime-organic stabilized soil has increased the soil strength by 185% at 90 days curing period at the design mix of organic clay + 10% lime +10% zeolite. The higher value of UCS indicates that zeolite is an effective catalyst to enhance lime stabilization.

Calcium carbonate synthesis with prescribed properties based on liquid waste of soda production

OpenAIRE

E.O. Mikhailova; V.O. Panasenko; N.B. Markova

2016-01-01

A promising direction in solving of environmental problems of soda industry is the development of low-waste resource-saving technologies, which consist in recycling of valuable waste components with obtaining the commercial products. Aim: The aim is to establish the optimal conditions for obtaining calcium carbonate with prescribed properties from liquid waste of soda production. Materials and Methods: Chemically deposited calcium carbonate is used as filler and should have certain physical a...

The use of hydrated lime in acid mine drainage treatment

Science.gov (United States)

Othman, Anuar; Sulaiman, Azli; Sulaiman, Shamsul Kamal

2017-05-01

Hydrated lime also known as calcium hydroxide with chemical formula Ca(OH)2 was used in this study as neutralization agent in acid mine drainage (AMD) treatment. Hydrated lime that is used to treat pool water samples from tin tailings located in Pengkalan Hulu, Perak was obtained from Simpang Pulai, Perak. The pH of water sample was around 2.6 to 2.8. Ten different variables of hydrated lime weights were used to treat 1 L of water sample. The weights of hydrated lime used were 0.2 g, 0.4 g, 0.6 g, 0.8 g, 1.0 g, 1.2 g, 1.4 g, 1.6 g, 1.8 g and 2.0 g. Time interval used was every 5 minutes up to minutes 30. Jar test method was used in this study. The maximum pH value of 5.93 ± 0.03 most approaches standard A and had complied standard B have been obtained using 2.0 g hydrated lime in 30-minute time interval. The concentration of arsenic, cadmium and chromium had decreased but only cadmium concentration did not comply with Standards A and B.

Analysis on soil compressibility changes of samples stabilized with lime

Directory of Open Access Journals (Sweden)

Elena-Andreea CALARASU

2016-12-01

Full Text Available In order to manage and control the stability of buildings located on difficult foundation soils, several techniques of soil stabilization were developed and applied worldwide. Taking into account the major significance of soil compressibility on construction durability and safety, the soil stabilization with a binder like lime is considered one of the most used and traditional methods. The present paper aims to assess the effect of lime content on soil geotechnical parameters, especially on compressibility ones, based on laboratory experimental tests, for several soil categories in admixture with different lime dosages. The results of this study indicate a significant improvement of stabilized soil parameters, such as compressibility and plasticity, in comparison with natural samples. The effect of lime stabilization is related to an increase of soil structure stability by increasing the bearing capacity.

Liming effect in the degradation of 14C-glyphosate in soils

International Nuclear Information System (INIS)

Arantes, Sayonara A.C.M.; Lavorenti, Arquimedes

2007-01-01

Liming is soil fertility management practice essential in tropical soils, in general extremely acidic. This practice, by influencing physical, chemical and biological features of soils may influence the behavior of organic molecules in soils. The glyphosate is one the most widely used pesticides in Brazil in several cultures to pest management control. Studies on its fate in soil are still incipient, mainly under the effect of liming practice The objective of the present study was to verify the effect of liming practice in the degradation of glyphosate in Red Latosol (LE) and Quartzarenic Neosol (RQ) soils and also in the microbial activity of the same soils. The experiment was conducted in a completely randomized design in a 2 x 2 factorial scheme, corresponding to two soils and two management conditions (with liming and without liming), with four replicates. The Radiometric technique was utilized to evaluate the evolution the 14 CO 2 at intervals of 7 days, during 70 days. The study of microbial activity was conducted parallel to the degradation experiment, using the methodology of radiolabelled glucose ( 14 C-glucose), which was measured at intervals of fourteen days, during 70 days. The results showed that in the studied soils, the liming increased the 14 C-glyphosate mineralization and the microbial activity. (author)

Effect of Lime Stabilization on Vertical Deformation of Laterite Halmahera Soil

Science.gov (United States)

Saing, Zubair; Djainal, Herry

2018-04-01

In this paper, the study was conducted to determine the lime effect on vertical deformation of road base physical model of laterite Halmahera soil. The samples of laterite soil were obtained from Halmahera Island, North Maluku Province, Indonesia. Soil characteristics were obtained from laboratory testing, according to American Standard for Testing and Materials (ASTM), consists of physical, mechanical, minerals, and chemical. The base layer of physical model testing with the dimension; 2m of length, 2m of width, and 1.5m of height. The addition of lime with variations of 3, 5, 7, an 10%, based on maximum dry density of standard Proctor test results and cured for 28 days. The model of lime treated laterite Halmahera soil with 0,1m thickness placed on subgrade layer with 1,5m thickness. Furthermore, the physical model was given static vertical loading. Some dial gauge is placed on the lime treated soil surface with distance interval 20cm, to read the vertical deformation that occurs during loading. The experimentals data was analyzed and validated with numerical analysis using finite element method. The results showed that the vertical deformation reduced significantly on 10% lime content (three times less than untreated soil), and qualify for maximum deflection (standard requirement L/240) on 7-10% lime content.

Diffusion and ionic conduction in oxide glasses

International Nuclear Information System (INIS)

Mehrer, H; Imre, A W; Tanguep-Nijokep, E

2008-01-01

The ion transport properties of soda-lime silicate and alkali borate glasses have been studied with complimentary tracer diffusion and impedance spectroscopy techniques in order to investigate the ion dynamics and mixed-alkali effect (MAE). In soda-lime silicate glasses the tracer diffusivity of 22 Na alkali ions is more than six orders of magnitude faster than the diffusivity of earth alkali 45 Ca ions. This observation is attributed to a stronger binding of bivalent earth alkali ions to the glass network as compared to that of alkali ions. The conductivity of the investigated standard soda-lime silicate glasses is mostly due to the high mobility of sodium ions and a temperature independent Haven ratio of about 0.45 is obtained. For single alkali sodium-borate glasses, the Haven ratio is also temperature independent, however, it is decreases with decreasing temperature for rubidium-borate glass. The MAE was investigated for Na-Rb borate glasses and it was observed that the tracer diffusivities of 22 Na and 86 Rb ions cross, when plotted as function of the relative alkali content. This crossover occurs near the Na/(Na+Rb) ratio of the conductivity minimum due to MAE. The authors suggest that this crossover and the trend of diffusion coefficients is the key to an understanding of the MAE

Structure change of soda-silicate glass by mechanical milling

International Nuclear Information System (INIS)

Iwao, M; Okuno, M

2010-01-01

Structure change of ground soda-silicate glass (SiO 2 -Na 2 O binary systems) was investigated using X-ray diffraction (XRD) and infrared spectroscopy. The measurement results were discussed comparison to that of SiO 2 glass. With increasing Na 2 O concentrations, the XRD intensity around 2θ = 22 0 decreased and the intensity around 32 0 increased. The intensity around 22 0 and 32 0 maybe attributed to SiO 2 glass structure unit and soda-silicate glass unit, respectively. The peaks of Na 2 CO 3 crystal for 2SiO 2 -Na 2 O glass were observed with increasing milling time. This crystallization was suggested that Na + ion on 2SiO 2 -Na 2 O glass surface connected CO 2 in air. The intensity around 22 0 and 32 0 decreased and the intensity around 30 0 increased with increasing milling time. These may indicate that SiO 2 glass structure unit and soda-silicate glass structure unit were mixed by milling. In addition, IR absorption band near v = 1100 cm -1 was separated to two bands near 940 cm -1 and 1070 cm -1 with increasing Na 2 O concentrations. The band near 940 cm -1 decreased and the band near 1070 cm -1 increased with increasing milling time. These spectra changes were suggested due to decrease of Na 2 O concentrations in 2SiO 2 -Na 2 O glass with Na 2 CO 3 crystallization.

Efficacy and phytotoicity of lime sulphur in organic apple production

NARCIS (Netherlands)

Holb, I.J.; Jong, de P.F.; Heijne, B.

2003-01-01

Curative and preventive efficacy and phytotoxicity of lime sulphur spray schedules, based on a warning system, were evaluated in the Netherlands during two growing seasons under field conditions. In most cases, lime sulphur treatments applied either curatively or preventively resulted in

Carbonation of lime and cement stabilized layers in road construction

CSIR Research Space (South Africa)

Netterberg, F

1984-04-01

Full Text Available The problem of deterioration of lime, lime-slag and cement stabilized pavement layers during curing, before sealing and in service is partly ascribed to carbonation of the stabilizer during curing and subsequent exposure to the atmosphere before...

Lime application methods, water and bottom soil acidity in fresh water fish ponds

Directory of Open Access Journals (Sweden)

Queiroz Julio Ferraz de

2004-01-01

Full Text Available Although some methods for determining lime requirement of pond soils are available and commonly used, there is still no consensus on whether it is more effective to apply liming materials to the bottoms of empty ponds or to wait and apply them over the water surface after ponds are filled. There is also little information on how deep lime reacts in pond sediment over time, and whether the depth of reaction is different when liming materials are applied to the water or to the soil. Therefore, three techniques for treating fish ponds with agricultural limestone were evaluated in ponds with clayey soils at a commercial fish farm. Amounts of agricultural limestone equal to the lime requirement of bottom soils were applied to each of three ponds by: direct application over the pond water surface; spread uniformly over the bottom of the empty pond; spread uniformly over the bottom of the empty pond followed by tilling of the bottom. Effectiveness of agricultural limestone applications did not differ among treatment methods. Agricultural limestone also reacted quickly to increase total alkalinity and total hardness of pond water to acceptable concentrations within 2 weeks after application. The reaction of lime to increase soil pH was essentially complete after one to two months, and lime had no effect below a soil depth of 8 cm. Tilling of pond bottoms to incorporate liming materials is unnecessary, and tilling consumes time and is an expensive practice; filled ponds can be limed effectively.

How state taxes and policies targeting soda consumption modify the association between school vending machines and student dietary behaviors: a cross-sectional analysis.

Science.gov (United States)

Taber, Daniel R; Chriqui, Jamie F; Vuillaume, Renee; Chaloupka, Frank J

2014-01-01

Sodas are widely sold in vending machines and other school venues in the United States, particularly in high school. Research suggests that policy changes have reduced soda access, but the impact of reduced access on consumption is unclear. This study was designed to identify student, environmental, or policy characteristics that modify the associations between school vending machines and student dietary behaviors. Data on school vending machine access and student diet were obtained as part of the National Youth Physical Activity and Nutrition Study (NYPANS) and linked to state-level data on soda taxes, restaurant taxes, and state laws governing the sale of soda in schools. Regression models were used to: 1) estimate associations between vending machine access and soda consumption, fast food consumption, and lunch source, and 2) determine if associations were modified by state soda taxes, restaurant taxes, laws banning in-school soda sales, or student characteristics (race/ethnicity, sex, home food access, weight loss behaviors.). Contrary to the hypothesis, students tended to consume 0.53 fewer servings of soda/week (95% CI: -1.17, 0.11) and consume fast food on 0.24 fewer days/week (95% CI: -0.44, -0.05) if they had in-school access to vending machines. They were also less likely to consume soda daily (23.9% vs. 27.9%, average difference  =  -4.02, 95% CI: -7.28, -0.76). However, these inverse associations were observed primarily among states with lower soda and restaurant tax rates (relative to general food tax rates) and states that did not ban in-school soda sales. Associations did not vary by any student characteristics except for weight loss behaviors. Isolated changes to the school food environment may have unintended consequences unless policymakers incorporate other initiatives designed to discourage overall soda consumption.

How state taxes and policies targeting soda consumption modify the association between school vending machines and student dietary behaviors: a cross-sectional analysis.

Directory of Open Access Journals (Sweden)

Daniel R Taber

Full Text Available Sodas are widely sold in vending machines and other school venues in the United States, particularly in high school. Research suggests that policy changes have reduced soda access, but the impact of reduced access on consumption is unclear. This study was designed to identify student, environmental, or policy characteristics that modify the associations between school vending machines and student dietary behaviors.Data on school vending machine access and student diet were obtained as part of the National Youth Physical Activity and Nutrition Study (NYPANS and linked to state-level data on soda taxes, restaurant taxes, and state laws governing the sale of soda in schools. Regression models were used to: 1 estimate associations between vending machine access and soda consumption, fast food consumption, and lunch source, and 2 determine if associations were modified by state soda taxes, restaurant taxes, laws banning in-school soda sales, or student characteristics (race/ethnicity, sex, home food access, weight loss behaviors..Contrary to the hypothesis, students tended to consume 0.53 fewer servings of soda/week (95% CI: -1.17, 0.11 and consume fast food on 0.24 fewer days/week (95% CI: -0.44, -0.05 if they had in-school access to vending machines. They were also less likely to consume soda daily (23.9% vs. 27.9%, average difference  =  -4.02, 95% CI: -7.28, -0.76. However, these inverse associations were observed primarily among states with lower soda and restaurant tax rates (relative to general food tax rates and states that did not ban in-school soda sales. Associations did not vary by any student characteristics except for weight loss behaviors.Isolated changes to the school food environment may have unintended consequences unless policymakers incorporate other initiatives designed to discourage overall soda consumption.

How State Taxes and Policies Targeting Soda Consumption Modify the Association between School Vending Machines and Student Dietary Behaviors: A Cross-Sectional Analysis

Science.gov (United States)

Taber, Daniel R.; Chriqui, Jamie F.; Vuillaume, Renee; Chaloupka, Frank J.

2014-01-01

Background Sodas are widely sold in vending machines and other school venues in the United States, particularly in high school. Research suggests that policy changes have reduced soda access, but the impact of reduced access on consumption is unclear. This study was designed to identify student, environmental, or policy characteristics that modify the associations between school vending machines and student dietary behaviors. Methods Data on school vending machine access and student diet were obtained as part of the National Youth Physical Activity and Nutrition Study (NYPANS) and linked to state-level data on soda taxes, restaurant taxes, and state laws governing the sale of soda in schools. Regression models were used to: 1) estimate associations between vending machine access and soda consumption, fast food consumption, and lunch source, and 2) determine if associations were modified by state soda taxes, restaurant taxes, laws banning in-school soda sales, or student characteristics (race/ethnicity, sex, home food access, weight loss behaviors.) Results Contrary to the hypothesis, students tended to consume 0.53 fewer servings of soda/week (95% CI: -1.17, 0.11) and consume fast food on 0.24 fewer days/week (95% CI: -0.44, -0.05) if they had in-school access to vending machines. They were also less likely to consume soda daily (23.9% vs. 27.9%, average difference = -4.02, 95% CI: -7.28, -0.76). However, these inverse associations were observed primarily among states with lower soda and restaurant tax rates (relative to general food tax rates) and states that did not ban in-school soda sales. Associations did not vary by any student characteristics except for weight loss behaviors. Conclusion Isolated changes to the school food environment may have unintended consequences unless policymakers incorporate other initiatives designed to discourage overall soda consumption. PMID:25083906

Advanced treatment of swine wastewater using an agent synthesized from amorphous silica and hydrated lime.

Science.gov (United States)

Tanaka, Yasuo; Hasegawa, Teruaki; Sugimoto, Kiyomi; Miura, Keiichi; Aketo, Tsuyoshi; Minowa, Nobutaka; Toda, Masaya; Kinoshita, Katsumi; Yamashita, Takahiro; Ogino, Akifumi

2014-01-01

Advanced treatment using an agent synthesized from amorphous silica and hydrated lime (M-CSH-lime) was developed and applied to swine wastewater treatment. Biologically treated wastewater and M-CSH-lime (approximately 6 w/v% slurry) were fed continuously into a column-shaped reactor from its bottom. Accumulated M-CSH-lime gradually formed a bed layer. The influent permeated this layer and contacted the M-CSH-lime, and the treatment reaction progressed. Treated liquid overflowing from the top of the reactor was neutralized with CO₂gas bubbling. The colour removal rate approximately exceeded 50% with M-CSH-lime addition rates of > 0.15 w/v%. The removal rate of PO(3⁻)(4) exceeded 80% with the addition of>0.03 w/v% of M-CSH-lime. The removal rates of coliform bacteria and Escherichia coli exceeded 99.9% with > 0.1 w/v%. Accumulated M-CSH-lime in the reactor was periodically withdrawn from the upper part of the bed layer. The content of citric-acid-soluble P₂O₅ in the recovered matter was>15% when the weight ratio of influent PO(3⁻)(4) -P to added M-CSH-lime was > 0.15. This content was comparable with commercial phosphorus fertilizer. The inhibitory effect of recovered M-CSH-lime on germination and growth of leafy vegetable komatsuna (Brassica rapa var. perviridis) was evaluated by an experiment using the Neubauer's pot. The recovered M-CSH-lime had no negative effect on germination and growth. These results suggest that advanced water treatment with M-CSH-lime was effective for simultaneous removal of colour, [Formula: see text] and coliform bacteria at an addition rate of 0.03-0.15 w/v%, and that the recovered M-CSH-lime would be suitable as phosphorus fertilizer.

Baking soda pica associated with rhabdomyolysis and cardiomyopathy in pregnancy.

Science.gov (United States)

Scolari Childress, Katherine M; Myles, Thomas

2013-08-01

Pica is a commonly underappreciated disorder in pregnancy that can lead to several complications, including severe metabolic derangements and other adverse outcomes. We report a case of baking soda pica in pregnancy associated with both rhabdomyolysis and cardiomyopathy. A multigravid woman at 37 weeks of gestation presented with weakness and severe hypokalemia. She subsequently had development of rhabdomyolysis and presumed peripartum cardiomyopathy. After delivery, it was discovered that the patient had a long history of consumption of large quantities of baking soda. Her condition improved with cessation of the pica. Clinicians must have a high index of suspicion for pica in pregnancy because it can lead to complex diagnostic challenges and pregnancy complications. The diagnosis should be considered in a patient with unexplained metabolic abnormalities.

Expansion reduction of clayey soils through Surcharge application and Lime Treatment

Directory of Open Access Journals (Sweden)

T. López-Lara

2017-12-01

Full Text Available Expansive clayey soils produce heaving and cracking of floor slabs and walls. Expansive soils owe their characteristics to the presence of swelling clay minerals. This soil expands and contracts due to changes in the moisture content of the soil. In this study the surcharge required to counteract soil expansion was measured in natural expansive soils (untreated soils and lime treated soils starting at 19.61 kPa (2 Ton/m2 and continuing with increments of 19.61 kPa. Additionaly in lime treated soils the amount of lime was determined under different surcharges in order to reduce the expansion. The test results indicated that the surcharges applied to untreated soils were not proportional to the decrease of expansion which is probably due to the increase of soil density. In fact, only the initial surcharge of 19.61 kPa significantly decreased the expansion. According to the results, the soil expansion was considerably reduced (1.54% with the surcharge of 78.45 kPa, therefore this surcharge can be considered as the Swelling pressure. On the other hand the soil tested (high compressibility clay was stabilized with 6% of lime (without surcharges which was determined with the lowest value of liquid limit and plastic index as well as expansion test. After the application of surcharges and lime treatment to expansive soil, the surcharges of 39.22 kPa and 58.84 kPa decreased expansion and increased their resistance. This was concluded by similar low values of expansion (without settlements under both surcharges of each treated soil tested (2, 4 and 6% of lime. It can be concluded that the surcharge contributed to the decrease of soil expansion due to the decrease of the amount of lime required (6% without surcharge. So, 4% of lime was enough for the surcharge of 19.61 kPa and 2% of lime required the surcharge minimum of 39.22 kPa. This shows that the surcharge of a house on expansive soil reduces soil expansion and therefore reduces costs of any

CHEMICAL SOIL ATTRIBUTES AS AFFECTED BY LIME AND GYPSUM SURFACE APPLICATION

Directory of Open Access Journals (Sweden)

A. Mantovani

2017-10-01

Full Text Available The gypsum is a soil condition end it has to function contribute to the elimination or reduction of aluminum in the soil in depth. Still, it can contribute to the distribution of nutrients in the soil profile more uniformly and thus increasing the productivity of crops. This study aimed to evaluate the influence of gypsum application, with and without lime, on soil chemical properties and soybean yield, in a no-till system. The experiment was carried in Campos Novos, Santa Catarina State, Brazil, with a randomized block design and split plot design with four replications, the main portion was distributed gypsum doses (1000, 2000, 4000 and 6000 kg ha-1 without incorporation, and the split plot (with and without lime and the liming was 2,000 kg ha-1. We evaluated the performance of components and productivity of soybeans. It was also analyzed the soil pH and Ca, Mg, S and Al at 0-20 and 20-40 cm. The application of gypsum at the rates tested surface with and without lime did not affect the yield components and soybean productivity. At 0-20 cm soil depth lime application increased soil pH by 0.3 units on the average rates of gypsum, but in the 20-40 cm layer was not found effect of lime and gypsum in pH ground due to the short time between application and evaluation. In areas with and without lime contents of Ca and S in the two layers evaluated increased with increasing rates of gypsum, since Mg has difference with the lime application on a 0-20 cm to dose 4000 kg ha-1 and the lime in the gypsum rates and Al decreased with increasing dose gypsum average in the 20-40 cm layer depth. The application of gypsum and limestone softened the negative effects of soil acidity and the increase mainly of calcium and sulfur at 0-20 cm, with less efficient effects in the 20-40 cm layer due to the soil is clayey and the period between the implementation and evaluation be 120 days.

Producer gas and its use for the manufacture of lime

Energy Technology Data Exchange (ETDEWEB)

Gupta, A K; Kumar, S

1976-04-01

An analysis of available data indicates that coal-based producer gas is superior to coal or wood as a fuel for lime kilns and much more readily available than oil or natural gas. With producer gas, chemical-grade lime is obtained, and the kiln capacity is increased, so that a smaller unit can be used or more lime obtained. With a mixture of coal and wood as the fuel, the lime produced is contaminated with ash. The added cost of the gas-producer unit can be paid out in one year owing to the greater demand for and the consequent higher prices obtainable for the chemical-grade product. In addition, the flue gases from the kiln can be used in place of steam to heat the gas producer, but experimental studies are needed to determine the magnitude of the savings in fuel consumption. 15 references.

Metagenomic insights into the uncultured diversity and physiology of microbes in four hypersaline soda lake brines

NARCIS (Netherlands)

Vavourakis, Charlotte D.; Ghai, Rohit; Rodriguez-Valera, Francisco; Sorokin, Dimitry Y.; Tringe, Susannah G.; Hugenholtz, Philip; Muyzer, Gerard

2016-01-01

Soda lakes are salt lakes with a naturally alkaline pH due to evaporative concentration of sodium carbonates in the absence of major divalent cations. Hypersaline soda brines harbor microbial communities with a high species- and strain-level archaeal diversity and a large proportion of still

Metagenomic Insights into the Uncultured Diversity and Physiology of Microbes in Four Hypersaline Soda Lake Brines

NARCIS (Netherlands)

Vavourakis, C.D.; Ghai, R.; Rodriguez-valera, F.; Sorokin, D.Y.; Tringe, S.G.; Hugenholtz, P.; Muyzer, G.

2016-01-01

Soda lakes are salt lakes with a naturally alkaline pH due to evaporative concentration of sodium carbonates in the absence of major divalent cations. Hypersaline soda brines harbor microbial communities with a high species- and strain-level archaeal diversity and a large proportion of still

Interpreting chemistry and technology of lime binders and implementing it in the conservation field

Directory of Open Access Journals (Sweden)

Georgia Zacharopoulou

2009-01-01

Full Text Available The objective of the paper is the compilation, review and dissemination of updated scientific knowledge on lime theory and technology in the field of heritage conservation. The strong evidence of the last decade's research on the positive effect of the - not demonstrable by a chemical equation – 'key' missing link of the maturation process is highlighted. It is demonstrated that the exceptional perfor -mance characteristics of durable lime based mortars predominately rely on the capacity for rapid, efficient and extensive carbonation of the air-hardening phase of limes, in particular when matured (nanoparticle wet slaked lime putties are used; and on the chemical and mechanical stability of the strength components (principally CSHs of the hydraulic phase of limes, which is higher in their more crystalline forms of historical lime-pozzolan mixtures than in their amorphous forms of modern cements. Hence, physicochemical adhesion and cohesion bonds both at the lime matrix and at the binder/aggregate interfaces are ensured imparting minimization of cracks and durability to lime based mortars and historic masonries. The comprehensive documentation of the former leads to optimal materials and procedures to preserve our cultural heritage.

Lime sulfur toxicity to broad mite, to its host plants and to natural enemies.

Science.gov (United States)

Venzon, Madelaine; Oliveira, Rafael M; Perez, André L; Rodríguez-Cruz, Fredy A; Martins Filho, Sebastião

2013-06-01

An acaricidal effect of lime sulfur has not been demonstrated for Polyphagotarsonemus latus. However, lime sulfur can cause toxicity to natural enemies and to host plants. In this study, the toxicity of different concentrations of lime sulfur to P. latus, to the predatory mite Amblyseius herbicolus and to the predatory insect Chrysoperla externa was evaluated. Additionally, the phytotoxicity of lime sulfur to two P. latus hosts, chili pepper and physic nut plants, was determined. Lime sulfur at a concentration of 9.5 mL L(-1) restrained P. latus population growth. However, this concentration was deleterious to natural enemies. The predatory mite A. herbicolus showed a negative value of instantaneous growth rate, and only 50% of the tested larvae of C. externa reached adulthood when exposed to 10 mL L(-1) . Physic nut had severe injury symptoms when sprayed with all tested lime sulfur concentrations. For chili pepper plants, no phytoxicity was observed at any tested concentration. Lime sulfur might be used for P. latus control on chili pepper but not on physic nut owing to phytotoxicity. Care should be taken when using lime sulfur in view of negative effects on natural enemies. Selective lime sulfur concentration integrated with other management tactics may provide an effective and sustainable P. latus control on chili pepper. © 2012 Society of Chemical Industry.

A novel eco-friendly technique for efficient control of lime water softening process.

Science.gov (United States)

Ostovar, Mohamad; Amiri, Mohamad

2013-12-01

Lime softening is an established type of water treatment used for water softening. The performance of this process is highly dependent on lime dosage. Currently, lime dosage is adjusted manually based on chemical tests, aimed at maintaining the phenolphthalein (P) and total (M) alkalinities within a certain range (2 P - M > or = 5). In this paper, a critical study of the softening process has been presented. It has been shown that the current method is frequently incorrect. Furthermore, electrical conductivity (EC) has been introduced as a novel indicator for effectively characterizing the lime softening process.This novel technique has several advantages over the current alkalinities method. Because no chemical reagents are needed for titration, which is a simple test, there is a considerable reduction in test costs. Additionally, there is a reduction in the treated water hardness and generated sludge during the lime softening process. Therefore, it is highly eco-friendly, and is a very cost effective alternative technique for efficient control of the lime softening process.

Investigation of Copper Sorption by Sugar Beet Processing Lime Waste

Science.gov (United States)

In the western United States, sugar beet processing for sugar recovery generates a lime-based waste product (~250,000 Mg yr-1) that has little liming value in the region’s calcareous soils. This area has recently experienced an increase in dairy production, with dairi...

Some studies on the reaction between fly ash and lime

Indian Academy of Sciences (India)

Unknown

Blain's air permeability apparatus was used for ... Pulverized lime with high per- centage of CaO (> 80 ... kept in a low-pressure autoclave at an average steam pressure and ... ing the solubility of lime in a solvent containing 1 part by volume of ...

Nutritional characteristics of two pigeon pea hybrids – Liming and phosphated fertilization

Directory of Open Access Journals (Sweden)

Marcia Atauri Cardelli de Lucena

2012-12-01

Full Text Available The use of legumes in animal production systems can be a sustainable alternative as a protein source in rotational grazing system and/or as a protein bank. Pigeon pea (Cajanus cajan (L. Millsp. figure as an example of success of this use on animal nutrition. The development of this species can be limited by the high acidity and low soil phosphorus content. There is a lack of scientific information on the effects of liming and phosphorus fertilization on some nutritional variables of two pigeon pea new hybrids. This study was conducted in pots containing 5 kg of soil in a greenhouse at the Instituto de Zootecnia, Nova Odessa, São Paulo State. There were studied two pigeon pea hybrids, H1 and H2, and the treatments involved agronomic practices: 1 No liming and without phosphorus (control, 2 Liming (L, 3 Phosphorus fertilization (P and 4 Liming plus phosphorus. Liming was proposed to increase soil base saturation to 50%, it was used dolomite lime PRNT = 90%, in an amount corresponding to 4.5 t/ha. Phosphorus fertilization (as superphosphate rate was 60 kg/ha of PO25. The experimental units were allocated according to a complete randomised block design, with five replications. We analyzed the levels of crude protein (CP, neutral detergent fiber (NDF, acid detergent fiber (ADF, in pigeon pea shoot at 45 days of age. Statistical analyzes were performed using the software SISVAR, averages were compared using test for multiple comparisons Student Newman-Keuls - SNK test (P < 0.05. The H1 hybrid had the highest content of CP, by applying P, lime plus P and the control treatment compared to H2 hybrid. The association lime plus P resulted in higher content of CP mainly due to the increased availability of P for plants. Smaller values were observed for NDF in H2 with P application. Lower values of ADF were observed in H1 in both control treatment and P application. The ADF values were lower for the hybrid H2 only for the treatment lime plus P. The two

The motivational benefits of a dentifrice containing baking soda and hydrogen peroxide.

Science.gov (United States)

Fischman, S L; Kugel, G; Truelove, R B; Nelson, B J; Cancro, L P

1992-01-01

Twenty-two family practice dentists, in a large metropolitan area, were recruited to act as independent examiners in a study to evaluate the compliance of their patients to accept a good oral hygiene regimen with the use of a fluoride dentifrice, containing hydrogen peroxide and baking soda, dispensed from a dual dispensing package. To evaluate compliance, the dentists attended an orientation seminar and were trained to assess gingival health using the CPITN periodontal probe. Each dentist evaluated the gingival health status of five to seven of his own patients, initially and after one and three months of product use following hygiene instruction and product assignment. One-hundred and thirty-one patients successfully completed the study. After one month of using the hydrogen peroxide/baking soda toothpaste, the mean reduction in bleeding sites was 53%; at three months the reduction was 62%. The hydrogen peroxide/baking soda dentifrice was well accepted by dentist and patient, and a discernible improvement in oral health of the patients was achieved when the product was used in a conscientious oral hygiene program.

Liming effect in the degradation of 14C-glyphosate in soils

Energy Technology Data Exchange (ETDEWEB)

Arantes, Sayonara A.C.M.; Lavorenti, Arquimedes [Universidade de Sao Paulo (USP), Piracicaba, SP (Brazil). Escola Superior de Agricultura Luiz de Queiroz]. E-mails: samoreno@esalq.usp.br; alavoren@esalq.usp.br; Tornisielo, Valdemar L. [Centro de Energia Nuclear na Agricultura (CENA), Piracicaba, SP (Brazil)]. E-mail: vltornis@cena.usp.br

2007-07-01

Liming is soil fertility management practice essential in tropical soils, in general extremely acidic. This practice, by influencing physical, chemical and biological features of soils may influence the behavior of organic molecules in soils. The glyphosate is one the most widely used pesticides in Brazil in several cultures to pest management control. Studies on its fate in soil are still incipient, mainly under the effect of liming practice The objective of the present study was to verify the effect of liming practice in the degradation of glyphosate in Red Latosol (LE) and Quartzarenic Neosol (RQ) soils and also in the microbial activity of the same soils. The experiment was conducted in a completely randomized design in a 2 x 2 factorial scheme, corresponding to two soils and two management conditions (with liming and without liming), with four replicates. The Radiometric technique was utilized to evaluate the evolution the {sup 14}CO{sub 2} at intervals of 7 days, during 70 days. The study of microbial activity was conducted parallel to the degradation experiment, using the methodology of radiolabelled glucose ({sup 14}C-glucose), which was measured at intervals of fourteen days, during 70 days. The results showed that in the studied soils, the liming increased the {sup 14}C-glyphosate mineralization and the microbial activity. (author)

Long-term field-scale experiment on using lime filters in an agricultural catchment.

Science.gov (United States)

Kirkkala, Teija; Ventelä, Anne-Mari; Tarvainen, Marjo

2012-01-01

The River Yläneenjoki catchment in southwest Finland is an area with a high agricultural nutrient load. We report here on the nutrient removal performance of three on-site lime-sand filters (F1, F2, and F3), established within or on the edge of the buffer zones. The filters contain burnt lime (CaO) or spent lime [CaO, Ca(OH), and CaCO]. Easily soluble lime results in a high pH level (>11) and leads to an efficient precipitation of soluble phosphorus (P) from the runoff. Water samples were taken from the inflow and outflow of each site in different hydrological situations. The length of the monitoring period was 4 yr for F1, 6 yr for F2, and 1.5 yr for F3. F1 and F2 significantly reduced the suspended solids (SS), total P (PTOT), and dissolved reactive P (DRP) in the treated water. The proportional reduction (%) varied but was usually clearly positive. Filter F3 was divided into two equal parts, one containing burnt lime and the other spent lime. Both filter parts removed PTOT and SS efficiently from the water; the burnt-lime part also removed DRP. The mixed-lime part removed DRP for a year, but then the efficiency decreased. The effect of filters on nitrogen compounds varied. We conclude that sand filters incorporating lime can be used together with buffer zones to reduce both P and SS load to watercourses. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Influence of Lime and Phosphorus Application Rates on Growth of Maize in an Acid Soil

Directory of Open Access Journals (Sweden)

Peter Asbon Opala

2017-01-01

Full Text Available The interactive effects of lime and phosphorus on maize growth in an acid soil were investigated in a greenhouse experiment. A completely randomized design with 12 treatments consisting of four lime levels, 0, 2, 10, and 20 t ha−1, in a factorial combination with three phosphorus rates, 0, 30, and 100 kg ha−1, was used. Maize was grown in pots for six weeks and its heights and dry matter yield were determined and soils were analyzed for available P and exchangeable acidity. Liming significantly reduced the exchangeable acidity in the soils. The effect of lime on available P was not significant but available P increased with increasing P rates. There was a significant effect of lime, P, and P by lime interactions on plant heights and dry matter. Without lime application, dry matter increased with increasing P rates but, with lime, dry mattes increased from 0 to 30 kg P ha−1 but declined from 30 to 100 kg P ha−1. The highest dry matter yield (13.8 g pot−1 was obtained with a combined 2 t ha−1 of lime with 30 kg P ha−1 suggesting that lime application at low rates combined with moderate amounts of P would be appropriate in this soil.

Imperial Limes - Projections in Medieval Imperial Idea

Directory of Open Access Journals (Sweden)

Z.Z. Zhekov

2015-08-01

Full Text Available Roman imperial limes from I - V BC was the first state border in world history, which in some sense corresponds to the modern concept of political boundary. It represents sustainable political, military and economic barrier between the Romans and the rest of the world. With minor modifications it retains their basic strategic concept during the period as expressed from the emperors Augustus and Tiberius. Limes become powerful barrier that separates cultural Roman Hellenistic world of the wild barbarian but at the same time limits the constructed infrastructure of roads, forts and towns became a natural cultural, commercial and political mediator between these two initially hostile worlds. In border towns developed a lively trade between Romans and barbarians. Roman traders penetrate inside the barbarian lands getting to know their culture and history. Studying foreign peoples and countries they convey information gathered imperial legate of the Roman population. The same process was developed and of course in the opposite direction. Exchange of information on the other promotes mutual understanding and open living on both sides of the Roman Limes.

The effect of reuse of unhairing-liming residual floats through ...

African Journals Online (AJOL)

STORAGESEVER

2008-09-03

Sep 3, 2008 ... Key words: Unhairing-liming process, reusing, leather industry, environment, bacterial and fungal numbers. INTRODUCTION .... 4.0 x101. -: No growth. Chemical analysis of samples. Chemical analyses of sodium sulphide and lime were done for the regeneration of ULP residual liquors. While preparing ...

40 CFR 180.1232 - Lime-sulfur; exemption from the requirement of a tolerance.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Lime-sulfur; exemption from the... Exemptions From Tolerances § 180.1232 Lime-sulfur; exemption from the requirement of a tolerance. An exemption from the requirement of a tolerance is established for residues of lime-sulfur. [70 FR 33363, June...

Hydrogenolysis and Activation of Soda Lignin Using [BMIM]Cl as a Catalyst and Solvent

Directory of Open Access Journals (Sweden)

Shengming Zhang

2017-07-01

Full Text Available To improve the reactivity of the soda lignin, an acid ionic liquid 1-butyl-3-mthylimidazolium chloride ([BMIM]Cl was used as the catalyst and solvent to degrade the soda lignin through hydrogenolysis. Structural elucidation of the lignin samples was conducted by using a combination of analytical methods including chemical analysis, ultraviolet spectrophotometry (UV spectrophotometry, Fourier transform infrared spectroscopy (FT-IR spectra, two-dimensional heteronuclear single quantum coherence nuclear magnetic resonance (2D-HSQC NMR techniques, and gel permeation chromatography (GPC. The antioxidant activities of the lignin samples were evaluated using the diammonium 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonate (ABTS+ radical scavenging and 1,1-diphenyl-2-picrylhydrazyl (DPPH radical scavenging methods. The degradation mechanism was proposed based on the characterization results. The optimal reaction condition was as follows: the concentration of [BMIM]Cl in the solution was 10 wt %, the hydrogen initial pressure was 3 MPa, and the solution was heated for 4 h at 90 °C. After the reaction, the total hydroxyl content of the soda lignin increased by 81.3%, while the phenolic hydroxyl content increased by 23.1%. At the same time, the weight-average molar mass of the soda lignin sample decreased from 8220 to 6450 g/mol with an improved antioxidant activity. In addition, approximately 56.7% of the β-O-4 linkages were degraded in the lreaction. The main effect of the acid ionic liquid [BMIM]C1 was related to the cleavage of β-O-4 linkages. This study has shown the potential of using the catalyzed soda lignin as a natural polymer antioxidant.

Audiovisual Documentation of an International Seminar : Case: LIME

OpenAIRE

Tikkanen, Kirsti; Rönnberg, Mira

2013-01-01

The aim of this Bachelor’s thesis is to create a documentary video of an international seminar held in Kerava, Finland, in June 2013. The seminar was called Learning on Immigration and Multicultural Education (LIME) and it was conducted by Kerava Adult Education Center (later Keravan Opisto). LIME was a two-year intercultural project funded by the European Union. Different non-governmental organizations and adult education centers from eight European countries took part on the project. The ai...

DEVELOPMENT OF TECHNIQUES FOR QUANTITATIVE ANALYSIS OF LIME FLOWERS

Directory of Open Access Journals (Sweden)

Demyanenko DV

2016-03-01

Full Text Available Introduction. The article is devoted to the development of techniques for quantitative analysis of lime flower in order to make amendments to existing pharmacopoeian monographs for this herbal drug. Lime inflorescences contain lipophilic biologically active substances (BAS causing notable antimicrobial and anti-inflammatory effects and also more polar phenolic compounds with antiulcer activity. Considering this, it’s necessary to regulate all these groups of BAS quantitatively. Materials and methods. For this study six batches of lime flowers harvested in 2008-2009 yrs. in Kharkiv, Rivno and Zhitomir regions were used as crude herbal drug. Loss on drying was determined by routine pharmacopoeian procedures. Total content of lipophilic substances was determined gravimetrically after Soxhlet extraction of samples 1, 5, 7 and 10 g in weight with methylene chloride, considering that by its extracting ability this solvent is close to liquefied difluorochloromethane (freon R22 used by us for obtaining of lipophilic complexes. The duration of complete analytical extraction was determined by infusion of six 10 g assays of lime flowers during 1, 2, 3, 4, 5, 6 hours, then quantity of lipophilic extractives was revealed gravimetrically. Quantity of essential oil in lime flowers was evaluated under the procedure of ЕР7, 2.8.12. Weight of the herbal drug sample was 200 g, distillation rate – 2,5- 3,5 ml/min, volume of distillation liquid (water – 500 ml, volume of xylene in the graduated tube – 0,50 ml. Total flavonoid content recalculated to quercetin was determined after hydrolysis with acidified acetone, withdrawing of flavonoid aglycones with ethylacetate and by further spectrophotometry of their complexes with aluminium chloride. All quantitative determinations were replicated five times for each assay. All chemicals and reagents were of analytical grade. Results and discussion. It was found that adequate accuracy of the analysis of lipophilic

Enhanced inhibition of Aspergillus niger on sedge (Lepironia articulata) treated with heat-cured lime oil.

Science.gov (United States)

Matan, N; Matan, N; Ketsa, S

2013-08-01

This study aimed to examine heat curing effect (30-100°C) on antifungal activities of lime oil and its components (limonene, p-cymene, β-pinene and α-pinene) at concentrations ranging from 100 to 300 μl ml(-1) against Aspergillus niger in microbiological medium and to optimize heat curing of lime oil for efficient mould control on sedge (Lepironia articulata). Broth dilution method was employed to determine lime oil minimum inhibitory concentration, which was at 90 μl ml(-1) with heat curing at 70°C. Limonene, a main component of lime oil, was an agent responsible for temperature dependencies of lime oil activities observed. Response surface methodology was used to construct the mathematical model describing a time period of zero mould growth on sedge as functions of heat curing temperature and lime oil concentration. Heat curing of 90 μl ml(-1) lime oil at 70°C extended a period of zero mould growth on sedge to 18 weeks under moist conditions. Heat curing at 70°C best enhanced antifungal activity of lime oil against A. niger both in medium and on sedge. Heat curing of lime oil has potential to be used to enhance the antifungal safety of sedge products. © 2013 The Society for Applied Microbiology.

EVALUATION OF LINERBOARD PROPERTIES FROM MALAYSIAN CULTIVATED KENAF SODA-ANTHRAQUINONE PULPS VERSUS COMMERCIAL PULPS

OpenAIRE

Ahmad Azizi Mossello; Jalaluddin Harun; Rushdan Ibrahim; Hossien Resalati; Seyed Rashid Fallah Shamsi; Paridah Md Tahir; Mohd Nor Mohad Yusoff

2010-01-01

Malaysian cultivated kenaf has been identified as a suitable raw material for linerboard production. This study examines the soda-antraquinone (soda-AQ) pulp of kenaf fibers versus old corrugated container (OCC) and unbleached softwood kraft pulps as the main sources for linerboard production. The results showed significant differences among the pulp properties. The unbleached kraft pulp with very high freeness required high beating to reach an optimized freeness and produced paper with the h...

Liming Poultry Manures to Kill Pathogens and Decrease Soluble Phosphorus

International Nuclear Information System (INIS)

Maguire, R.; Hesterberg, D.; Gernat, A.; Anderson, K.; Wineland, M.; Grimes, J.

2006-01-01

Received for publication September 9, 2005. Stabilizing phosphorus (P) in poultry waste to reduce P losses from manured soils is important to protect surface waters, while pathogens in manures are an emerging issue. This study was conducted to evaluate CaO and Ca(OH) 2 for killing manure bacterial populations (pathogens) and stabilizing P in poultry wastes and to investigate the influence on soils following amendment with the treated wastes. Layer manure and broiler litter varying in moisture content were treated with CaO and Ca(OH) 2 at rates of 2.5, 5, 10, and 15% by weight. All treated wastes were analyzed for microbial plate counts, pH, and water-soluble phosphorus (WSP), while a few selected layer manures were analyzed by phosphorus X-ray absorption near edge structure (XANES). A loamy sand and a silt loam were amended with broiler litter and layer manure treated with CaO at rates of 0, 2.5, 5, 10, and 15% and soil WSP and pH were measured at times 1, 8, and 29 d. Liming reduced bacterial populations, with greater rates of lime leading to greater reductions; for example 10% CaO applied to 20% solids broiler litter reduced the plate counts from 793 000 to 6500 mL -1 . Liming also reduced the WSP in the manures by over 90% in all cases where at least 10% CaO was added. Liming the manures also reduced WSP in soils immediately following application and raised soil pH. The liming process used successfully reduced plate counts and concerns about P losses in runoff following land application of these limed products due to decreased WSP

Liquid wastes from mining and milling of uranium ores - a laboratory study of treatment methods

International Nuclear Information System (INIS)

Ryan, R.K.; Alfredson, P.G.

1976-10-01

Methods of reducing the concentration of contaminants in mine water and in the acidic raffinate from uranium milling operations have been studied. Lime, limestone, caustic soda and lime-soda ash mixtures were compared as reagents for neutralising raffinates and for removing amines and heavy metals including radium from solution. All methods of neutralisation reduced contaminant levels significantly. Two-stage neutralisation using limestone in the first stage to pH 4, followed by second stage lime treatment appears to be an economically attractive approach. This method usually gave the lowest residual radium concentration provided the solids from the first stage were not removed before adding lime. Radium can be further removed from neutralised raffinates or from mine water conditioned with sulphate by the addition of barium chloride to co-precipitate the sulphates of barium and radium. The concentration of radium was readily reduced to less than 3 pCi l -1 by adding 10 mg Ba l -1 raffinate. For mine waters conditioned to 0.01 M in sulphate, barium additions of 20 mg l -1 were required to attain the same radium concentrations. Adsorption on barytes was also effective in removing radium from conditioned mine water and neutralised raffinates. (author)

Baking soda as an abrasive in toothpastes: Mechanism of action and safety and effectiveness considerations.

Science.gov (United States)

Hara, Anderson T; Turssi, Cecilia P

2017-11-01

Toothpastes can be formulated with different abrasive systems, depending on their intended clinical application. This formulation potentially affects their effectiveness and safety and, therefore, requires proper understanding. In this article, the authors focused on abrasive aspects of toothpastes containing sodium bicarbonate (baking soda), which have gained considerable attention because of their low abrasivity and good compatibility, while providing clinical effectiveness (further detailed in the other articles of this special issue). The authors first appraised the role of toothpaste abrasivity on tooth wear, exploring some underlying processes and the existing methods to determine toothpaste abrasivity. The authors reviewed the available data on the abrasivity of toothpastes containing baking soda and reported a summary of findings highlighting the clinical implications. On the basis of the collected evidence, baking soda has an intrinsic low-abrasive nature because of its comparatively lower hardness in relation to enamel and dentin. Baking soda toothpastes also may contain other ingredients, which can increase their stain removal effectiveness and, consequently, abrasivity. Even those formulations have abrasivity well within the safety limit regulatory agencies have established and, therefore, can be considered safe. Copyright © 2017 American Dental Association. Published by Elsevier Inc. All rights reserved.

'Closed Circuit' Anaesthesia

African Journals Online (AJOL)

its constant-flow flowmeters and accurate vaporisers, there. Department of Anaesthesia ... Enough evidence has accumulated on the dangers of long periods of ... form in the soda-lime. To understand how these problems may .be solved, one.

Classical Methods and Calculation Algorithms for Determining Lime Requirements

Directory of Open Access Journals (Sweden)

André Guarçoni

Full Text Available ABSTRACT The methods developed for determination of lime requirements (LR are based on widely accepted principles. However, the formulas used for calculation have evolved little over recent decades, and in some cases there are indications of their inadequacy. The aim of this study was to compare the lime requirements calculated by three classic formulas and three algorithms, defining those most appropriate for supplying Ca and Mg to coffee plants and the smaller possibility of causing overliming. The database used contained 600 soil samples, which were collected in coffee plantings. The LR was estimated by the methods of base saturation, neutralization of Al3+, and elevation of Ca2+ and Mg2+ contents (two formulas and by the three calculation algorithms. Averages of the lime requirements were compared, determining the frequency distribution of the 600 lime requirements (LR estimated through each calculation method. In soils with low cation exchange capacity at pH 7, the base saturation method may fail to adequately supply the plants with Ca and Mg in many situations, while the method of Al3+ neutralization and elevation of Ca2+ and Mg2+ contents can result in the calculation of application rates that will increase the pH above the suitable range. Among the methods studied for calculating lime requirements, the algorithm that predicts reaching a defined base saturation, with adequate Ca and Mg supply and the maximum application rate limited to the H+Al value, proved to be the most efficient calculation method, and it can be recommended for use in numerous crops conditions.

76 FR 82295 - Central Power & Lime LLC; Notice of Filing

Science.gov (United States)

2011-12-30

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket Nos. EL12-18-000; QF82-207-007] Central Power & Lime LLC; Notice of Filing December 23, 2011. Take notice that on December 22, 2011, Central Power & Lime LLC, pursuant to sections 18 CFR 292.205(c) and 385.207 of the Federal Energy...

A nano approach to consolidation of degraded historic lime mortars

Czech Academy of Sciences Publication Activity Database

Drdácký, Miloš; Slížková, Zuzana; Ziegenbalg, G.

2009-01-01

Roč. 8, č. 2 (2009), s. 13-22 ISSN 1662-5250 R&D Projects: GA ČR(CZ) GA103/06/1609 Institutional research plan: CEZ:AV0Z20710524 Keywords : lime water * calcium hydroxide nanosuspension * lime mortar Subject RIV: AL - Art, Architecture, Cultural Heritage Impact factor: 0.571, year: 2009

Going flat: examining heterogeneity in the soda-obesity relationship by subgroup and place of birth among Asian Americans.

Science.gov (United States)

Alcalá, Héctor E; Sharif, Mienah Z

2017-06-01

To determine if the association between soda consumption and obesity is uniform among Asian-American population subgroups. We conducted multivariate logistic regression analyses on odds of being obese among seven Asian subgroups and by place of birth using data from the 2009 California Health Interview Survey. An omnibus population-based health survey. Non-institutionalized adults, aged 18 years or over, residing in California (n 36 271). Despite low levels of soda consumption in several Asian-American ethnic groups, soda consumption increased the odds of being obese among Chinese, Koreans and Other Asians but not for Whites. Obesity risk varied across Asian subgroups and by place of birth within these subgroups. More public health efforts addressing soda consumption in Asian-American communities are needed as a strategy for not only preventing chronic diseases but also disparities, considering the varying levels of soda intake across subgroups. Results support the growing body of literature critiquing acculturation theory in immigrant health research by documenting inconsistent findings by place of birth. Future research should take into account the heterogeneity among Asian Americans to advance our understanding of health outcomes and disparities.

Differences in the rheological properties of calcitic and dolomitic lime slurries: influence of particle characteristics and practical implications in lime-based mortar manufacturing

Directory of Open Access Journals (Sweden)

Arizzi, A.

2012-06-01

Full Text Available The study of the rheological properties of lime suspensions is a useful means to evaluate the workability of lime mortars. In this work, we studied the flow behaviour of two industrial hydrated limes, one of calcitic and the other of dolomitic composition, by means of two types of rheometer with different geometry and setup mode. The obtained results were interpreted taking into account the differences in microstructure and surface properties of the suspended particles. Calcitic lime dry particles are formed by angular and polydisperse clusters and, once dispersed in water, they behave like thixotropic materials. On the other hand, the dolomitic lime is formed by nanoparticles and small round cluster and it shows a pronounced plastic behaviour in suspension. This fundamental difference between the two materials explains the traditional preference for dolomitic lime mortars for plastering and rendering applications.

El estudio de las propiedades reológicas de suspensiones de cal es una herramienta muy útil para evaluar la trabajabilidad de morteros de cal. En este trabajo se ha estudiado el comportamiento en suspensión de dos cales hidratadas, de composición calcítica y dolomítica, mediante dos tipos de reómetros con geometría y modalidades distintas de medida. Los resultados obtenidos se han interpretado teniendo en cuenta las diferencias en la microestructura y las propiedades de superficie de las partículas en suspensión. Las partículas de cal calcítica están formadas por aglomerados angulares y polidispersos y, una vez dispersadas en agua, presentan un comportamiento tixotrópico. Por su parte, la cal dolomítica está formada por nanopartículas y pequeños agregados redondeados y muestra en suspensión un pronunciado comportamiento plástico. Esta importante diferencia entre las dos cales explica la preferencia tradicional de morteros de cal dolomítica para aplicaciones en revocos.

Effect of organosolv and soda pulping processes on the metals content of non-woody pulps.

Science.gov (United States)

González, M; Cantón, L; Rodríguez, A; Labidi, J

2008-09-01

In this work the effect of different pulping processes (ethyleneglycol, diethyleneglycol, ethanolamine and soda) of tow abounded raw materials (empty fruit bunches - EFB and rice straw) on the ash, silicates and metals (Fe, Zn, Cu, Pb, Mn, Ni and Cd) content of the obtained pulps have been studied. Results showed that pulps obtained by diethyleneglycol pulping process presented lower metals content (756 microg/g and 501 microg/g for EFB and rice straw pulp, respectively) than soda pulps (984 microg/g and 889 microg/g). Ethanolamine pulps presented values of holocellulose (74% and 77% for EFB and rice straw pulp, respectively), alpha-cellulose (74% and 69%), kappa number (18.7 and 18.5) and viscosity (612 and 90 6ml/g) similar to those of soda pulp, and lower lignin contents (11% and 12%).

Utilization of slaked lime for the regulation of pH value in the process of copper

Directory of Open Access Journals (Sweden)

Petković Aleksandar V.

2009-01-01

Full Text Available The investigations of used lime at plant from company Messer-Tehnogas, Belgrade, were in the aim to improvement technologically results from flotation concentration of copper minerals in flotation plant Veliki Krivelj. This paper shows usage of slaked lime, which is waste in the process of technical gas production, for regulation of pH value in the process of copper minerals flotation concentration. It is important to point out that slaked lime is a waste material that is not dangerous. Preparation and dosage includes preparation procedures, which enable introduction into flotation process with the aim of achieving better results. Lime from Limekiln Zagrađe is brought into four storage places in flotation. Volume of each storage place is 80 m3. Lime in pieces from storage place is added by airbladders on transportation line and by system of transportation lines lime gets to the ball mill. At the mill entrance water is added and then follows lime grinding. Milk glass of lime thus prepared goes to the pump basket from where is transported by pipeline to conditioner, and then by manual and (or automatic valves it is dosed to the flotation concentration of copper minerals process. Prospect of advancement and rationalization of the used lime in flotation plant Bor, Veliki Krivelj and Majdanpek as well as a way to link different branches of industry was demonstrated. Total cost of lime supplying, transporting, preparation and distribution related slaked lime is lower for 2.955 din/kg. Particularly, using lime from Messer in content of 2.1 g/l value of pH 11.82 is possible to obtain.

Flue gas desulphurization in a spray tower with de-coupled recycling of soda ash

Energy Technology Data Exchange (ETDEWEB)

Liebgott, H.

1983-05-01

RD project to develop a ''dry'' process for the desulphurization of flue gases. The process is based on a desulphurization step with a solution of soda ash which is sprayed into the flue gas. The gas is cooled by evaporation but its temperature is still higher than the dew point; reheating is not necessary. The product of the desulphurization is a dry mixture of sodium sulphite and -carbonate. It is intended to reprocess this powder to soda in a central plant - serving several power stations. First sulphite is oxidized to sulphate, which in turn is reacted with calcium chloride to form calcium sulphate and sodium chloride. The latter is introduced into the Solvay-soda ash process which yields calcium chloride as a by-product. Tests were carried out for the desulphurization step and the oxidation of sulphite. The desulphurization tests resulted in poor degrees of SO/sub 2/-removal even with high stoichiometric ratios of soda ash to sulphur dioxide. The preliminary estimates of process economics made before start of experimental work could not be verified. Furthermore, during work on the project, new processes were revealed whereby flue gas is desulphurized in a spray-drying apparatus with a slurry of calcium hydroxide. In an extension of the project, tests were carried out which confirmed these findings. The project was abandoned.

Development of an efficient and economic small scale management scheme for low-and intermediate level radioactive waste and its impact on the environment

International Nuclear Information System (INIS)

Salomon, A.Ph.; Panem, J.A.; Manalastas, H.C.; Cortez, S.L.; Paredes, C.H.; Bartolome, Z.M.

1976-05-01

This paper is a preliminary report on the evolution of a pilot-scale management system for low-and intermediate level radioactive wastes to provide adequate protection to the public as well as maintain the equilibrium in the human environment. Discussions on the waste management and disposal scheme proposals, assessment of waste treatment requirements of the Atomic Research Center, Philippine Atomic Energy Commission, previous experiences in the handling and management of radioactive wastes, current practices and alternatives to meet waste management problems and research studies on waste treatment are presented. In the selection of a chemical treatment process for ARC, comparative studies on the different waste processing methods or combination of processes that will be most suitable for the waste requirements of the Center are now in progress. The decontamination efficiency and economy of the lime-soda, ferrocyanide phosphate and ferric hydroxide methods are being compared. Jar experiments were conducted in the Lime-Soda Process to establish the optima conditions for certain parameter required in order to achieve an efficient and economical treatment system applicable to the local conditions for attaining maximum removal of contamination; maximum settling time - 5 hours after treatment, optimum pH-11, 2:3 ppm ratio of Ca +2 to Co 3 -2 concentration, concentration of dosing reagents can further be increased beyond 160 ppm Ca +2 and 240 ppm Co 3 -2 . Cobalt contamination can be removed with lime-soda treatment aside from strontium

Admixture of lime in connection with deep rotary cultivation for short rotation energy forest

Energy Technology Data Exchange (ETDEWEB)

Danfors, B; Stambeck, A; Aasberg, G

1985-01-01

Spaghnum soils, which could be used for production of short rotation energy forests (Salix), require lime for the adjustment of the pH-level to obtain production at acceptable levels. It is necessary that the lime is distributed uniformly in the soil profile to a depth of at least 40-50 cm. The investigation has studied three methods of spreading and incorporating lime in the uppermost layer of soil. The first method concerned ploughing of peat soil with a conventional agricultural plough, the second method concerned rotovation with an agricutural rotovator to maximally 20 cm depth. In both cases the lime has been spread with a centrifugal broadcaster before the soil tillage. The third method implied simultaneous spreading of the lime and rotovation of the peat to a depth of maximally 50 cm, JTI has built and constructed a machine for this purpose. Ploughing as the only method of soil tillage of peat soils before planting of short rotation energy forests is rejected for two reasons. 1. Certain peat soils which have such mechanical properties that they immediately completely clog a plough. 2. The deficient distribution of lime in the ploughed layer. Rotovation with an agricultural rotovator has been done with good results. The delivery of lime in connection with the rotovation works well provided that the lime is dry. The peat is efficiently disintegrated and the lime gets a sufficiently uniform admixture. The cultivation depth, 40-50 cm, appears to be sufficient for the Salix plants to cope with the water supply during the summer. Limitations which should be discussed concern the cost of such an intensive and deep tillage of the peat.

Nutrient leaching potential following application of papermill lime-sludge to an acidic clay soil

Directory of Open Access Journals (Sweden)

S. C. Vettorazzo

2001-09-01

Full Text Available This experiment was carried out under greenhouse conditions with soil pots during 210 days, to evaluate the effect of calcitic papermill lime-sludge application (at the rates 0, 773, 1.547, and 2.320 mg kg-1 or respective equivalents to control, 2, 4, and 6 t ha-1, on chemical composition of soil leachate and its effects on eucalypt growth and yield. Highest soil leachate pH, SO4, and Na concentrations occurred in the 4 and 6 t ha-1 treatments. Soil leachate nitrate concentrations decreased with increasing lime-sludge rate. Soil leachate phosphate remained low (below the detection limit in all treatments until 120 days, while the concentration increased in the lime-sludge treatments at 210 days (last sampling in about 600 mg L-1. Lime-sludge decreased leachate Mg concentration, but had no significant effect among rates. Soil leachate Ca, K, B, Cu, Fe, and Zn did not change significantly for any lime-sludge application rates. The maximum NO3, Ca, Mg, K, and Na concentrations in the soil leachate occurred at 60 days after lime-sludge application (leaching equivalent to 1 pore volume, but for pH and SO4, the maximum occurred at 210 days (leaching equivalent to 4 pore volumes. Lime-sludge application decreased the concentration of exchangeable Al in the soil. Plant diameter growth and dry matter yield were increased with increasing lime-sludge rate. Beneficial effects on mineral nutrition (P, K, Ca, B, and Zn of eucalypts were also obtained by the application of 4 and 6 t ha-1 of lime-sludge.

Terrestrial liming benefits birds in an acidified forest in the northeast.

Science.gov (United States)

Pabian, Sarah E; Brittingham, Margaret C

2007-12-01

Studies in Europe have reported negative effects of acid deposition on forest birds, and research in North America has identified links between forest bird abundance and rates of acid deposition. We examined the bird community in an acidified forest in central Pennsylvania (USA) and evaluated the effects of terrestrial lime application on birds. We used a before-after control-impact (BACI) study design, with one year of observation before (2003) and three years after lime application (2004, 2005, and 2006). Between the 2003 and 2004 field seasons, 4500 kg/ha of dolomitic lime were applied to two of four 100-ha watersheds. Each year, we monitored bird abundance and Ovenbird (Seiurus aurocapilla) eggshell thickness and territory size. Soil and snail abundance data were also collected. The bird community and territory size results indicated that the study area may be providing low-quality habitat for forest birds, perhaps as a result of acid deposition. We found lower forest bird abundances than have been found in less acidified areas of Pennsylvania, and larger Ovenbird territory sizes than have been found in other studies. We found a significant positive relationship between soil calcium and bird abundance, indicating that soil calcium may affect bird abundance. Liming increased soil calcium and pH and led to increased snail and bird abundances. After liming, bird abundance was positively related to snail abundance. No significant changes occurred in Ovenbird territory size or eggshell thickness. Our results suggest that acid deposition could be responsible for reduced bird abundance, and that liming is a potential mitigation technique.

Experimental Effects of Lime Application on Aquatic Macrophytes: 2. Growth Response Versus Treatment Time and Lime Concentration

National Research Council Canada - National Science Library

James, William F; Barko, John W

2006-01-01

This research investigated the effects of applying lime (as calcium hydroxide; Ca(OH)2) either early or later in the life cycle on the growth, survivorship, and reproductive success of Sago Pondweed...

Effects of hydrated lime on radionuclides stabilization of Hanford tank residual waste.

Science.gov (United States)

Wang, Guohui; Um, Wooyong; Cantrell, Kirk J; Snyder, Michelle M V; Bowden, Mark E; Triplett, Mark B; Buck, Edgar C

2017-10-01

Chemical stabilization of tank residual waste is part of a Hanford Site tank closure strategy to reduce overall risk levels to human health and the environment. In this study, a set of column leaching experiments using tank C-104 residual waste were conducted to evaluate the leachability of uranium (U) and technetium (Tc) where grout and hydrated lime were applied as chemical stabilizing agents. The experiments were designed to simulate future scenarios where meteoric water infiltrates through the vadose zones into the interior of the tank filled with layers of grout or hydrated lime, and then contacts the residual waste. Effluent concentrations of U and Tc were monitored and compared among three different packing columns (waste only, waste + grout, and waste + grout + hydrated lime). Geochemical modeling of the effluent compositions was conducted to determine saturation indices of uranium solid phases that could control the solubility of uranium. The results indicate that addition of hydrated lime strongly stabilized the uranium through transforming uranium to a highly insoluble calcium uranate (CaUO 4 ) or similar phase, whereas no significant stabilization effect of grout or hydrated lime was observed on Tc leachability. The result implies that hydrated lime could be a great candidate for stabilizing Hanford tank residual wastes where uranium is one of the main concerns. Published by Elsevier Ltd.

Note: Making tens of centimeter long uniform microfluidic channels using commercial glass pipette

Science.gov (United States)

Ou, Neil; Lee, Huang-Ming; Wu, Jong-Ching

2018-03-01

Producing microchannels with diameters between 10 and 20 μm and with lengths in the tens of centimeters is reported. The method can be modified to obtain diameters as narrow as 350 nm. Length-to-diameter aspect ratios that surpass 104 can be produced for a fraction of current production costs. The controllable channel is produced by applying a flame to the narrow end of a commercial pipette that is made from a soda-lime silicate. In combination with a pulling mechanism, applying heat to the composite material lengthens the pipette in a highly uniform way. Given that the materials and methods in this research are cost-effective when compared to femtosecond laser micromachining on 2D silicon-based surfaces, further research into producing microchannels from soda-lime silicates may revolutionize access to 3D controllable microchannels.

Effect of Lime on characteristics of consolidation, strength, swelling and plasticity of fine grained soil

Science.gov (United States)

Estabragh, A. R.; Bordbar, A. T.; Parsaee, B.; Eskandari, Gh.

2009-04-01

Using Lime as an additive material to clayey soil is one of the best effective technique in building the soil structures to get some purposes such as soil stabilization, soil reinforcement and decreasing soil swelling. In this research the effect of Lime on geotechnical characteristics of a clayey soil was investigated. Soil specimen types used in this study were consisted of clayey soil as the control treatment and clay mixed with different weight fractions of lime, 4, 6, 8 & 10 percent. Some experiments such as CBR, atterburg limits, compaction, consolidation and swelling was conducted on specimens. Results revealed that adding lime to soil would change its physical and mechanical properties. Adding lime increase the compression strength and consolidation coefficient and decrease swelling potential and maximum dry density. According to the results, Atterburg experiments show that presence of lime in soil increase the liquid limit of low plasticity soil and decrease the liquid limit of high plasticity soil, but totally it decreases the plasticity index of soils. Key words: soil stabilization, lime, compression strength, swelling, atterburg limits, compaction

Arsenic immobilization by calcium-arsenic precipitates in lime treated soils

International Nuclear Information System (INIS)

Moon, Deok Hyun; Dermatas, Dimitris; Menounou, Nektaria

2004-01-01

Lime-based stabilization/solidification (S/S) can be an effective remediation alternative for the immobilization of arsenic (As) in contaminated soils and sludges. However, the exact immobilization mechanism has not been well established. Based on previous research, As immobilization could be attributed to sorption and/or inclusion in pozzolanic reaction products and/or the formation of calcium-arsenic (Ca-As) precipitates. In this study, suspensions of lime-As and lime-As-kaolinite were studied in an attempt to elucidate the controlling mechanism of As immobilization in lime treated soils. Aqueous lime-As suspensions (slurries) with varying Ca/As molar ratios (1:1, 1.5:1, 2:1, 2.5:1 and 4:1) were prepared and soluble As concentrations were determined. X-Ray diffraction (XRD) analyses were used to establish the resulting mineralogy of crystalline precipitate formation. Depending on the redox state of the As source, different As precipitates were identified. When As (III) was used, the main precipitate formation was Ca-As-O. With As(V) as the source, Ca 4 (OH) 2 (AsO 4 ) 2 ·4H 2 O formed at Ca/As molar ratios greater than 1:1. A significant increase in As (III) immobilization was observed at Ca/As molar ratios greater than 1:1. Similarly, a substantial increase in As (V) immobilization was noted at Ca/As molar ratios greater than or equal to 2.5:1. This observation was also confirmed by XRD. Lime-As-kaolinite slurries were also prepared at different Ca/As molar ratios. These slurries were used to specifically investigate the possibility of forming pozzolanic reaction products. Such products would immobilize As by sorption and/or inclusion along with the formations of different As precipitates. Toxicity Characteristic Leaching Procedure (TCLP) tests were used to evaluate As leachability in these slurries. XRD analyses revealed no pozzolanic reaction product formation. Instead, As immobilization was found to be precipitation controlled. The same Ca-As precipitate, Ca

Acidic deposition: State of science and technology. Report 15. Liming acidic surface waters. Final report

International Nuclear Information System (INIS)

Olem, H.; Thornelof, E.; Sandoy, S.; Schreiber, R.K.

1990-09-01

The document describes the science and technology of aquatic liming--a method for improving the water quality of acidic surface waters to restore or enhance fisheries. The report is a comprehensive compilation of years of research in North America and Europe by dozens of scientists. Several mitigation technologies--including those that have only been proposed--are critically evaluated along with the effects of liming on water chemistry and aquatic biota. Through these evaluations, the state of the science and technology of aquatic liming is identified for the reader. Whole-lake liming is now recognized as a valuable management tool for acidic surface waters and their fisheries. However, some liming technologies are considered experimental and will need further evaluation. Distinctions between technologies are included--as is the distinction between liming acidic surface waters and reducing acidifying emissions

A randomized crossover clinical study showing that methylphenidate-SODAS improves attention-deficit/hyperactivity disorder symptoms in adolescents with substance use disorder

Directory of Open Access Journals (Sweden)

C.M. Szobot

2008-03-01

Full Text Available Our objective was to evaluate the effectiveness of a long-acting formulation of methylphenidate (MPH-SODAS on attention-deficit/hyperactivity disorder (ADHD symptoms in an outpatient sample of adolescents with ADHD and substance use disorders (SUD. Secondary goals were to evaluate the tolerability and impact on drug use of MPH-SODAS. This was a 6-week, single-blind, placebo-controlled crossover study assessing efficacy of escalated doses of MPH-SODAS on ADHD symptoms in 16 adolescents with ADHD/SUD. Participants were randomly allocated to either group A (weeks 1-3 on MPH-SODAS, weeks 4-6 on placebo or group B (reverse order. The primary outcome measures were the Swanson, Nolan and Pelham Scale, version IV (SNAP-IV and the Clinical Global Impression Scale (CGI. We also evaluated the adverse effects of MPH-SODAS using the Barkley Side Effect Rating Scale and subject reports of drug use during the study. The sample consisted of marijuana (N = 16; 100% and cocaine users (N = 7; 43.8%. Subjects had a significantly greater reduction in SNAP-IV and CGI scores (P < 0.001 for all analyses during MPH-SODAS treatment compared to placebo. No significant effects for period or sequence were found in analyses with the SNAP-IV and CGI scales. There was no significant effect on drug use. MPH-SODAS was well tolerated but was associated with more severe appetite reduction than placebo (P < 0.001. MPH-SODAS was more effective than placebo in reducing ADHD symptoms in a non-abstinent outpatient sample of adolescents with comorbid SUD. Randomized clinical trials, with larger samples and SUD intervention, are recommended.

Study of lime vs. no lime in cold in-place recycled asphalt concrete pavements : final report.

Science.gov (United States)

1991-09-01

The resilient characteristics of cold in-place recycled asphalt concrete with and without lime were examined. Six core samples were obtained from a site two months after construction; six months later, six additional core samples were obtained from t...

Self-healing of lime based mortars: Microscopy observations on case studies

NARCIS (Netherlands)

Lubelli, B.; Nijland, T.G.; Hees, R.P.J. van

2011-01-01

Lime mortars have, up to a certain extent, a self-healing capacity which may contribute to their durability. Self-healing in lime mortars consists of a process of dissolution, transport and re-precipitation of calcium compounds to heal cracks and fissures. The spontaneous occurrence of self-healing

Self-healing of lime based mortars : Microscopy observations on case studies

NARCIS (Netherlands)

Lubelli, B.; Nijland, T.G.; Van Hees, R.P.J.

2011-01-01

Lime mortars have, up to a certain extent, a self-healing capacity which may contribute to their durability. Self-healing in lime mortars consists of a process of dissolution, transport and re-precipitation of calcium compounds to heal cracks and fissures. The spontaneous occurrence of self-healing

Contrasting the genetic patterns of microbial communities in Soda lakes with and without cyanobacterial bloom

OpenAIRE

Andreote, A. P. D.; Dini-Andreote, F.; Rigonato, J.; Machineski, G. S.; Souza, B. C. E.; Barbiéro, Laurent; Rezende, A. T.; Fiore, M. F.

2018-01-01

Soda lakes have high levels of sodium carbonates and are characterized by salinity and elevated pH. These ecosystems are found across Africa, Europe, Asia, Australia, North, Central, and South America. Particularly in Brazil, the Pantanal region has a series of hundreds of shallow soda lakes (ca. 600) potentially colonized by a diverse haloalkaliphilic microbial community. Biological information of these systems is still elusive, in particular data on the description of the main taxa involved...

Influence of natural pozzolana and lime additives on the temporal variation of soil compaction and shear strength

Science.gov (United States)

Harichane, Khelifa; Ghrici, Mohamed; Missoum, Hanifi

2011-06-01

Soil stabilization has been practiced for quite some time by adding mixtures, such as cement, lime and fly ash. The additives of lime (L), natural pozzolana (NP) or a combination of both were investigated here on the impact on the temporal variation of geotechnical characteristics of two cohesive soils. Lime and natural pozzolana were added at the content of 0-8% and 0-20%, respectively. The soil specimens were cured for 1, 7, 28 and 90 days and then tested for shear strength. Our data show that a combination of lime with natural pozzolana causes the increase in the maximum dry density but the decrease in the optimum moisture content in the gray soil, and vice verse in the red soil. The shear stress of both cohesive soils stabilized with lime or with the combination of lime and natural pozzolana was found to increase with time. The cohesion and the internal friction angle in lime-added samples were demonstrated to increase with time. The combination of lime with natural pozzolana exhibits a significant effect on the enhancement of the cohesion and the internal friction angle at later stages. The lime-natural pozzolana combination appears to produce higher shear parameters than lime or natural pozzolana used alone.

Impact of lime treated soils performance on design of earthfill dikes

Directory of Open Access Journals (Sweden)

Nerincx Nicolas

2016-01-01

Full Text Available Nowadays soil treatment with lime in civil engineering is widespread in many countries on all continents, within several construction fields. The interest of the hydraulic works community regarding this technique is currently growing. It has been indeed shown during the last decade that appropriate treatment technologies provide lime treated soils with high level properties such as excellent homogeneity, low permeability, internal and external erosion resistance and mechanical stability. Those have been shown in laboratory and for some properties with full scale experiments. The so conferred soil properties can lead to innovative earthfill dams and dikes designs by addressing some of the typical designer’s problems, such as stability, watertightness, internal erosion, surface protection and flood control. However, lime treated soil external erosion resistance is still to be quantified in the field for proper designing and dimensioning of lime treated soil external erosion protection or spillways. With this purpose, an experimental earthfill dike has been built along the river Vidourle (France in July 2015, in the frame of the French R&D program “DigueELITE”. This 50 m long and 3,5 m high dike is made of lime treated silt and is provided with sensors (succion, water content and temperature and piezometer in order to be monitored. It will also be tested against surface erosion. The final objective of this R&D program is to provide guidelines for designing innovative overflow resistant earthfill dikes. This article describes the performance reached by lime treated soils and associated design requirements and application; the experimental dike construction and lessons learned; the monitoring program; the dike design perspectives opened by soil treatment.

Investigation of Hydraulic Binding Characteristics of Lime Based Mortars Used in Historical Masonry Structures

Science.gov (United States)

Binal, Adil

2017-10-01

In the historic masonry structures, hard and large rock fragments were used as the construction materials. The hydraulic binder material prepared to keep this used material in its entirety is a different material than the cement used today. Khorasan mortar made by using aggregate and lime exhibits a more flexible structure than the concrete. This feature allows the historic building to be more durable. There is also a significant industrial value because of the use of Khorasan mortar in the restoration of historic masonry structures. Therefore, the calculation of the ideal mixture of Khorasan mortar and the determination of its mechanical and physical properties are of great importance regarding preserving historic buildings. In this study, the mixtures of different lime and brick fractions were prepared. It was determined that Khorasan mortar shows the highest compressive strength in mixtures with water/lime ratio of 0.55 and lime/aggregate ratio of 0.66. By keeping the mixing ratio constant, it was observed that the strengths of the samples kept in the humidity chamber for different curing times increased day by day. The early strength values of samples with the high lime/aggregate ratio (l/a: 0.83) were higher than those with the low lime/aggregate ratio (l/a: 0.5). For the samples with low lime/aggregate ratio, there was an increase in the strength values depending on the curing period. As the cure duration increases, a chemical reaction takes place between the lime and the brick fracture, and as a result of this reaction, the strength values are increased.

Effect of annealing atmosphere on microstructure, optical and ...

Indian Academy of Sciences (India)

61

properties of spray pyrolysed indium doped Zn(O,S) thin films .... prepared solution was sprayed by a compressed air assisted system on a clean soda lime glass .... flake-like structures contract from their sides to produce compact film with ...

Assessment of soda ash calcination treatment of Turkish trona ore

Directory of Open Access Journals (Sweden)

Gezer Sibel

2016-01-01

Full Text Available Trona is relatively rare, non-metallic mineral, Na2CO3 · NaHCO3 · 2H2O. The pure material contains 70.3% sodium carbonate and by calcination the excess CO2 and water can be driven off, yielding natural soda ash. The terms soda ash and sodium carbonate are used interchangeably. Trona calcining is a key process step in production of soda ash (sodium carbonate anhydrate from the relatively cheap trona ore. The calcination reaction may proceeds in a sequence of steps. Depending on the conditions, it may result in formation of either sodium carbonate monohydrate (Na2CO3 · H2O, sodium sesquicarbonate or weigschederite (Na2CO3 · 3NaHCO3. The Beypazarı Turkish trona deposit is the second largest deposit in the world with the content of 84% trona. The decomposition of trona appeared to be a single stage process across the temperature range studied (150-200 °C with the representative samples of different size fractions in the draught up metallurgical furnace. The optimum particle size and calcination time were −6.35 mm and 30 minutes, respectively, at calcination temperature of 175 °C in a metallurgical furnace. Microwave-induced dry calcination of trona was possible and 5 minutes of calcination time at a power level of 900 was sufficient for complete calcination of −6.35 mm feed. This includes short time calcinations with the goal of improving economics and simplifying the thermal process.

A four-week clinical study to evaluate and compare the effectiveness of a baking soda dentifrice and an antimicrobial dentifrice in reducing plaque.

Science.gov (United States)

Ghassemi, Annahita; Vorwerk, Linda M; Hooper, William J; Putt, Mark S; Milleman, Kimberly R

2008-01-01

To evaluate and compare the effectiveness in reducing plaque of a fluoride dentifrice containing baking soda and a non-baking soda fluoride dentifrice containing an antimicrobial (triclosan/copolymer) system after a single brushing and over a four-week period of daily brushing. A total of 207 subjects completed this randomized, blinded, parallel-group clinical study. Twenty-four hour plaque buildup was scored at baseline and after two and four weeks of twice-daily use of the products. Additionally, controlled single brushing with the assigned dentifrice, followed by post-brushing plaque assessment, was performed at the start (baseline visit) and end (Week-4 visit) of the study. Plaque was scored using the Turesky, et al. modification of Quigley-Hein Index at six sites per tooth, according to Soparkar's modification. Mean baseline whole mouth plaque scores for the baking soda and triclosan dentifrice groups were 2.90 +/- 0.40 and 2.90 +/- 0.39, respectively, and the difference was not statistically significant. Within-group analysis showed that both products significantly reduced the amount of plaque over the four-week period (p baking soda dentifrice exhibited significantly greater reduction in plaque scores (p baking soda dentifrice group (0.34 +/- 0.32) was 2.22-fold greater than that observed for the triclosan dentifrice group (0.15 +/- 0.24). Similarly, single brushing with the baking soda dentifrice showed a 1.88- to 2.08-fold greater pre- to post-brushing plaque difference as compared to the triclosan dentifrice at the baseline visit (mean plaque reduction: baking soda 0.54 +/- 0.26; triclosan 0.28 +/- 0.18; ratio 1.88X) and Week-4 visit (baking soda 0.47 +/- 0.21; triclosan 0.23 +/- 0.15; ratio 2.08X). Similar to the whole mouth scores, evaluation of various tooth sites (facial, lingual, proximal, and gingival) showed a significantly greater reduction in plaque scores for brushing with the baking soda dentifrice as compared to brushing with the triclosan

Soda-Lime-Silicate Float Glass: A Property Comparison

Science.gov (United States)

2017-10-01

temperature. West Conshohocken (PA): ASTM International; 2012. 4. Quinn GD, Swab JJ . Fracture toughness of glasses as measured by the SCF and SEPB methods...Swab JJ , Patel PJ, Tran X, Gilde L, Luoto E, Gaviola MH, Gott A, Paulson B, Kilczewski S. Equibiaxial flexure strength of glass: influence of glass

REMOVAL OF BERYLLIUM FROM DRINKING WATER BY CHEMICAL COAGULATION AND LIME SOFTENING

Science.gov (United States)

The effectiveness of conventional drinking water treatment and lime softening was evaluated for beryllium removal from two drinking water sources. ar test studies were conducted to determine how common coagulants (aluminum sulfate and ferric chloride and lime softening performed ...

Destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Urquhart, D

1882-08-19

Manufacture of ammonia and purification of shale oils are described. In the distillation of shales, increase of ammonia is obtained and the oils are less contaminated by sulfur, by mixing a small proportion, about two to three percent, of lime or slaked line with the shale. The same process is used with other carbonaceous substances containing nitrogen, such as peat, coal, or the like; but a smaller proportion of lime is used than in the former case, and the lime is slaked with caustic soda solution. When slack or waste coal or other carbonaceous substances are distilled by heated air or gases arising from imperfect combustion, as in furnaces on the gas producer principle, slaked lime is added to the slack or other material.

A Comparison between Lime and Alkaline Hydrogen Peroxide Pretreatments of Sugarcane Bagasse for Ethanol Production

Science.gov (United States)

Rabelo, Sarita C.; Filho, Rubens Maciel; Costa, Aline C.

Pretreatment procedures of sugarcane bagasse with lime (calcium hydroxide) or alkaline hydrogen peroxide were evaluated and compared. Analyses were performed using 2 × 2 × 2 factorial designs, with pretreatment time, temperature, and lime loading and hydrogen peroxide concentration as factors. The responses evaluated were the yield of total reducing sugars (TRS) and glucose released from pretreated bagasse after enzymatic hydrolysis. Experiments were performed using the bagasse as it comes from an alcohol/ sugar factory and bagasse in the size range of 0.248 to 1.397 mm (12-60 mesh). The results show that when hexoses and pentoses are of interest, lime should be the pretreatment agent chosen, as high TRS yields are obtained for nonscreened bagasse using 0.40 g lime/g dry biomass at 70 °C for 36 h. When the product of interest is glucose, the best results were obtained with lime pretreatment of screened bagasse. However, the results for alkaline peroxide and lime pretreatments of nonscreened bagasse are not very different.

An introduction to LIME 1.0 and its use in coupling codes for multiphysics simulations.

Energy Technology Data Exchange (ETDEWEB)

Belcourt, Noel; Pawlowski, Roger Patrick; Schmidt, Rodney Cannon; Hooper, Russell Warren

2011-11-01

LIME is a small software package for creating multiphysics simulation codes. The name was formed as an acronym denoting 'Lightweight Integrating Multiphysics Environment for coupling codes.' LIME is intended to be especially useful when separate computer codes (which may be written in any standard computer language) already exist to solve different parts of a multiphysics problem. LIME provides the key high-level software (written in C++), a well defined approach (with example templates), and interface requirements to enable the assembly of multiple physics codes into a single coupled-multiphysics simulation code. In this report we introduce important software design characteristics of LIME, describe key components of a typical multiphysics application that might be created using LIME, and provide basic examples of its use - including the customized software that must be written by a user. We also describe the types of modifications that may be needed to individual physics codes in order for them to be incorporated into a LIME-based multiphysics application.

Sugar-sweetened beverage and diet soda consumption and the 7-year risk for type 2 diabetes mellitus in middle-aged Japanese men.

Science.gov (United States)

Sakurai, M; Nakamura, K; Miura, K; Takamura, T; Yoshita, K; Nagasawa, S Y; Morikawa, Y; Ishizaki, M; Kido, T; Naruse, Y; Suwazono, Y; Sasaki, S; Nakagawa, H

2014-02-01

This cohort study investigated the association between sugar-sweetened beverage (SSB) and diet soda consumption and the incidence of type 2 diabetes in Japanese men. The participants were 2,037 employees of a factory in Japan. We measured consumption of SSB and diet soda using a self-administered diet history questionnaire. The incidence of diabetes was determined in annual medical examinations over a 7-year period. Hazard ratios (HRs) with 95 % confidence intervals (CIs) for diabetes were estimated after adjusting for age, body mass index, family history, and dietary and other lifestyle factors. During the study, 170 participants developed diabetes. The crude incidence rates (/1,000 person-years) across participants who were rare/never SSB consumers, Diet soda consumption was significantly associated with the incident risk of diabetes (P for trend = 0.013), and multivariate-adjusted HRs compared to rare/never diet soda consumers were 1.05 (0.62-1.78) and 1.70 (1.13-2.55), respectively, for participants who consumed diet soda was significantly associated with an increased risk for diabetes in Japanese men. Diet soda is not always effective at preventing type 2 diabetes even though it is a zero-calorie drink.

Lime Kiln Modeling. CFD and One-dimensional simulations

Energy Technology Data Exchange (ETDEWEB)

Svedin, Kristoffer; Ivarsson, Christofer; Lundborg, Rickard

2009-03-15

The incentives for burning alternative fuels in lime kilns are growing. An increasing demand on thorough investigations of alternative fuel impact on lime kiln performance have been recognized, and the purpose of this project has been to develop a lime kiln CFD model with the possibility to fire fuel oil and lignin. The second part of the project consists of three technical studies. Simulated data from a one-dimensional steady state program has been used to support theories on the impact of biofuels and lime mud dryness. The CFD simulations was carried out in the commercial code FLUENT. Due to difficulties with the convergence of the model the calcination reaction is not included. The model shows essential differences between the two fuels. Lignin gives a different flame shape and a longer flame length compared to fuel oil. Mainly this depends on how the fuel is fed into the combustion chamber and how much combustion air that is added as primary and secondary air. In the case of lignin combustion the required amount of air is more than in the fuel oil case. This generates more combustion gas and a different flow pattern is created. Based on the values from turbulent reaction rate for the different fuels an estimated flame length can be obtained. For fuel oil the combustion is very intense with a sharp peak in the beginning and a rapid decrease. For lignin the combustion starts not as intense as for the fuel oil case and has a smoother shape. The flame length appears to be approximately 2-3 meter longer for lignin than for fuel oil based on turbulent reaction rate in the computational simulations. The first technical study showed that there are many benefits of increasing dry solids content in the lime mud going into a kiln such as increased energy efficiency, reduced TRS, and reduced sodium in the kiln. However, data from operating kilns indicates that these benefits can be offset by increasing exit gas temperature that can limit kiln production capacity. Simulated

77 FR 45715 - Application of Key Lime Air Corporation for Commuter Authority

Science.gov (United States)

2012-08-01

... DEPARTMENT OF TRANSPORTATION Office of the Secretary [Docket DOT-OST-2009-0116] Application of Key Lime Air Corporation for Commuter Authority AGENCY: Department of Transportation. ACTION: Notice of... Lime Air Corporation fit, willing, and able, and awarding it a Commuter Air Carrier Authorization...

Influence of the sintering temperature in the microstructure of foam glass obtained from waste glass

International Nuclear Information System (INIS)

Pokorny, A.; Vicenzi, J.; Bergmann, C.P.

2012-01-01

In this work, foam glasses were produced from grounded soda-lime glass and a synthetic carbonate, used as a foaming agent, with a similar composition to a dolomite lime, added with different oxides (SiO 2 , Al 2 O 3 , Fe 2 O 3 , MnO 2 , Na 2 O, K 2 O, TiO 2 and P 2 O 5 ). The objective was to evaluate the influence of sintering temperature on the properties and microstructure of the obtained material. In addition, the effect of addition of the oxides in the expansion of the ceramic bodies was evaluated. The ceramic bodies were formulated with 3 weight percent of synthetic carbonate, uniaxially pressed and fired within the temperature range from 700 deg C to 950 deg C, with a heating rate of 150K/h. The technological characterization of the ceramic bodies involved the determination of the volumetric expansion and their microstructures have been characterized by optical microscopy and scanning electron microscopy. The experimental results have shown foam glass can be obtained from grounded soda-lime glass, using synthetic carbonate, with the introduction of the different oxides, as foaming agent. (author)

Belowground ectomycorrhizal fungal communities respond to liming in three southern Swedish coniferous forest stands

DEFF Research Database (Denmark)

Kjøller, Rasmus; Clemmensen, Karina

2009-01-01

In this study we report on changes in the belowground ectomycorrhizal fungal communities in southern Swedish coniferous forests as a consequence of liming with 3-7 ton limestone per hectare 16 years prior to the study. A total of 107 ectomycorrhizal fungi were identified from 969 independently...... sampled root tips by sequencing the internal transcribed spacer region of the ribosomal DNA. Forty, 59 and 51 species were identified in three pine and spruce forests. Within all sites only about 25% of the species overlapped between the limed and the reference areas. However, the most abundant species...... were often found in both limed and reference plots and 60-70% of the root tips at each site were colonised by species occurring in both limed and reference plots. Across all three sites, fungal species belonging to the genus Tylospora and the order Pezizales became significantly more frequent in limed...

California Bearing Ratio (CBR) test on stabilization of clay with lime addition

Science.gov (United States)

Hastuty, I. P.; Roesyanto; Limbong, M. N.; Oberlyn, S. J.

2018-02-01

Clay is a type of soil with particles of certain minerals giving plastic properties when mixed with water. Soil has an important role in a construction, besides as a building material in a wide variety of civil engineering works, soil is also used as supporting foundation of the building. Basic properties of clay are rock-solid in dry and plastic with medium water content. In high water content, clay becomes sticky like (cohesive) and soften. Therefore, clay stabilization is necessary to repair soil’s mechanical properties. In this research, lime is use as a stabilizer that contains the Ca+ element to bond bigger particles. Lime used is slaked lime Ca(OH)2. Clay used has liquid limitation (LL) value of 47.33%, plasticity index of 29.88% and CBR value 6.29. The results explain about 10% lime mixture variation gives the optimum stabilized clay with CBR value of 8.75%.

Structural adaptation of Salsola soda L. (Chenopodiaceae from inland and maritime saline area

Directory of Open Access Journals (Sweden)

Milić Dubravka M.

2013-01-01

Full Text Available The microscopic analysis of leaf and stem in two populations of Salsola soda was carried out in order to examine mechanism of anatomical adaptations to environmental condition on saline habitats and to determine if there exists a morpho-anatomical differentiation between populations from maritime and inland saline area. Analysis included 26 quantitative characters of leaf and stem. The results showed that both populations exhibited halomorphic and xeromorphic adaptations, which refered to ecological plasticity and adaptations of plants to their habitats. Our research also showed that S. soda had quite a stable morphoanatomical structure, since only quantitative changes were recorded. [Projekat Ministarstva nauke Republike Srbije, br. 173002

Positive and negative aspects of soda/anthraquinone pulping of hardwoods.

Science.gov (United States)

Francis, R C; Bolton, T S; Abdoulmoumine, N; Lavrykova, N; Bose, S K

2008-11-01

The positive aspects of the non-sulfur soda/anthraquinone (SAQ) process are mostly tied to improved energy efficiency while lower pulp brightness after bleaching is its most significant drawback. A credible method that quantifies bleachability as well as an approach that solves the problem for SAQ pulps from hardwoods will be described. A straight line correlation (R2=0.904) was obtained between O2 kappa number and final light absorption coefficient (LAC) value after standardized OD0EpD1 bleaching of nine hardwood kraft pulps from three laboratories and one pulp mill. The bleachability of pulps from four different soda processes catalyzed by anthraquinone (AQ) and 2-methylanthraquinone (MAQ) was compared to that of conventional kraft pulps by comparing O2 kappa number decrease and final LAC values. It was observed that a mild hot water pre-hydrolysis improved the bleachability of SAQ pulps to a level equal to that of kraft.

Effects of watershed and in-stream liming on macroinvertebrate communities in acidified tributaries to an Adirondack lake

Science.gov (United States)

George, Scott D.; Baldigo, Barry P.; Lawrence, Gregory B.; Fuller, Randall L.

2018-01-01

Liming techniques are being explored as a means to accelerate the recovery of aquatic biota from decades of acid deposition in many regions. The preservation or restoration of native sportfish populations has typically been the impetus for liming programs, and as such, less attention has been given to its effects on other biological assemblages such as macroinvertebrates. Furthermore, the differing effects of various lime application strategies such as in-stream and watershed applications are not well understood. In 2012, a program was initiated using in-stream and aerial (whole-watershed) liming to improve water quality and Brook Trout (Salvelinus fontinalis) recruitment in three acidified tributaries of a high-elevation Adirondack lake in New York State. Concurrently, macroinvertebrates were sampled annually between 2013 and 2016 at 3 treated sites and 3 untreated reference sites to assess the effects of each liming technique on this community. Despite improvements in water chemistry in all three limed streams, our results generally suggest that neither liming technique succeeded in improving the condition of macroinvertebrate communities. The watershed application caused an immediate and unsustained decrease in the density of macroinvertebrates and increase in the proportion of sensitive taxa. These changes were driven primarily by a one-year 71 percent reduction of the acid-tolerant Leuctra stoneflies and likely represent an initial chemistry shock from the lime application rather than a recovery response. The in-stream applications appeared to reduce the density of macroinvertebrates, particularly in one stream where undissolved lime covered the natural substrate. The close proximity of our study sites to the in-stream application points (50 and 1230 m) may partly explain these negative effects. Our results are consistent with prior studies of in-stream liming which indicate that this technique often fails to restore macroinvertebrate communities to a pre

Differences in nitrogen and urea metabolism between goats bred for ...

African Journals Online (AJOL)

glacial acetic acid and dried over H2S04 and soda lime to remove radioactivity .... by factors such as rumen ammonia concentration, volatile fatty acid production ... breed differences observed in this study, but the fact that urea excretion rate in ...

Radiation dose estimation from the radioactivity analysis of lime and cement used in Bangladesh

International Nuclear Information System (INIS)

Alam, M.N.; Miah, M.M.H.; Chowdhury, M.I.; Kamal, M.; Ghose, S.; Islam, M.N.; Mustafa, M.N.; Miah, M.S.R.

1999-01-01

The radioactivity concentrations of 232 Th, 226 Ra, 40 K and 137 Cs were measured using high-resolution γ-ray spectrometry in limestone, powdered lime, by-product lime and cement used in Bangladesh. The activity concentrations, Ra equivalent activities, representative level index values for all samples and the effective dose equivalents due to the intake of the above-mentioned radionuclides in limestone and powdered lime by the adult group were estimated. The mean activity concentrations of 232 Th, 226 Ra and 40 K were 60.8, 60.2 and 928 Bq kg -1 , respectively for limestone, 107, 68.0 and 1660 Bq kg -1 , respectively, for powdered lime and 83.0, 31.0 and 972 Bq kg -1 , respectively, for by-product lime. For cement, the mean activity concentrations of 232 Th, 226 Ra and 40 K were observed to be 54.3, 29.7 and 523 Bq kg -1 , respectively. The presence of 137 Cs was not detectable in any of the studied samples. The measured average activities of 232 Th, 226 Ra and 40 K for all samples were relatively higher than the world typical values except for 226 Ra in cement and by-product lime. The calculated mean Ra equivalent values for limestone, powdered lime, by-product lime and cement were 219, 349, 224 and 148 Bq kg -1 , respectively. The corresponding representative level index values were found to be 1.63, 2.63, 1.68 and 1.09, respectively. The mean effective dose equivalent values of 232 Th, 226 Ra and 40 K for limestone were 56.5x10 -7 , 41.6x10 -8 and 50.8x10 -10 Sv g -1 , respectively, and those for powdered lime were 99.5x10 -7 , 46.9x10 -8 and 91.3x10 -10 Sv g -1 , respectively. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

High-temperature counter-flow recuperator

Science.gov (United States)

Rudloff, F.

1981-05-01

The commercial potential of a helical recuperator design in recovering waste heat from industrial furnaces is reported. The helical recuperator concept consists of a cylindrical column with an interior helical interface which separates the preheat air and the combustion gas. The column operates in a teer flow mode and is formed from modular sections. The material evaluation consisted of exposing material samples to a soda-lime glass furnace environment for a fifteen week period. ECP-3, X-81, and Unichrome were the best suited for use in a soda-lime environment and ECP-3 was the best candidate with respect to manufacturing. Two potential design modifications were identified: a finned design and a double helix design. For materials that showed the greatest potential for use in the glass environment, the double helix design made from ECP-3 was the most economical producing payback periods of 6 to 14 years.

Effect of liquid liming on sorghum growth in an Ultisol.

Directory of Open Access Journals (Sweden)

Manuel E. Camacho

2015-06-01

Full Text Available   The aim of this study was to evaluate the effects of the application of liquid lime on sorghum growth in an Ultisol. This research was conducted between August and November, 2011 at the Agricultural Research Center, San José, Costa Rica. In an Ultisol planted with sorghum, in pots of 800 ml, the following treatments where applied: control without lime, calcium carbonate at doses of 10 and 20 l/ha, magnesium oxide at doses of 10 and 20 l/ha, calcium carbonate + magnesium oxide at doses of 5 + 5 and 10 + 10 l/ha, respectively. Six weeks after planting, sorghum was harvested, measuring leaf area, dry and fresh weight of the aerial and root biomass, nutrient absorption and the soil chemical characteristics. Treatments using calcium carbonate and calcium carbonate + magnesium oxide obtained the best values of leaf area and the higher weight of the aerial and root biomass of sorghum. Even though there were no significant differences between liquid lime treatments, there were regarding control without lime and weight biomass variables. Liquid calcium carbonate significantly increased Ca absorption, and the calcium carbonate + magnesium oxide treatment at doses of 10 l/h showed the highest Mg absorption. All amendment treatments caused an improvement of the soil fertility, the most notable being the application of 20 l/ha of magnesium oxide that dropped the exchangeable acidity from 9.02 to 0.36 cmol(+/l, acidity saturation dropped from 95 to 3.3%, and pH increased from 5 to 5.7. It was concluded that the liquid liming amendments had a positive effect over the crop and the soil fertility.

The relationships among lemons, limes and citron: a chromosomal comparison.

Science.gov (United States)

Carvalho, R; Soares Filho, W S; Brasileiro-Vidal, A C; Guerra, M

2005-01-01

Lemons, limes and citron constitute a group of closely related Citrus species, whose species delimitations and taxonomic relationships are unclear. In order to identify karyotypic similarities and species relationships within this group, the CMA+/DAPI- banding pattern and the distribution of the 5S and 45S rDNA sites of 10 accessions of lime, lemon, and citron were investigated. The four cultivars of C. limon analyzed showed the same pattern of CMA+ bands and rDNA sites, suggesting that they originated from a single germplasm, later differentiated by distinct somatic mutations. The lemons C. jambhiri, C. limonia and C. volkameriana displayed karyotypes very similar to each other, but they differed from C. limon by the absence of a single chromosome with one band in each telomere. The limes, C. aurantifolia and C. limettioides, seemed less related to each other and exhibited different heteromorphic chromosome pairs. In C. aurantifolia, the presence of a chromosome type unknown in all other Citrus species cytologically known so far supports the assumption that this accession may be derived from a hybrid with a species from the subgenus Papeda or from another genus. Citrus medica was the only homozygous accession of this group and all of its chromosome types were clearly represented in limes and lemons, some of them forming heteromorphic pairs. The analysis of the distribution of rDNA sites allowed a further refinement of the comparison among accessions. The lemons and limes were heterozygous for all rDNA sites, whereas C. medica was entirely homozygous. These data support the hypothesis that C. medica is a true species while the other nine accessions are hybrids. Copyright 2005 S. Karger AG, Basel.

The effect of baking soda when applied to bleached enamel prior to restorative treatment.

Science.gov (United States)

Tostes, Bhenya Ottoni; Mondelli, Rafael Francisco Lia; Lima-Arsati, Ynara Bosco de Oliveira; Rodrigues, Jose Augusto; Costa, Leonardo Cesar

2013-08-01

This in vitro study evaluated the effect of 10% baking soda solution and sodium bicarbonate powder (applied with jets) when applied to bleached enamel prior to restorative treatment. The surfaces of 40 bovine incisors were flattened and divided into 5 groups (n = 8): Group B (bleached and restored, negative control), Group W (bleached, stored in distilled water for 7 days, and restored), Group BSJ (bleached, abraded with baking soda jet for 1 min, and restored), Group BSS (bleached, application of 10% baking soda solution for 5 min, and restored), and Group R (restored, without bleaching, positive control). The samples were bleached in 1 session with 3 applications of 35% HP-based gel and activated with a LED appliance for 9 min each. Resin composite cylinders (2 mm height and 0.8 mm diameter) were made on the enamel surface after the acid etching and a conventional 1-step single vial adhesive application was performed. After storage in distilled water (37 ± 1°C, 24 hr), the microshear bond test was performed (1 mm/min). ANOVA and Tukey tests were applied to compare the results. The mean results of these tests showed that Groups W, BBS, and R were not statistically different. These groups also indicated a higher bond strength when compared with Groups B and BSJ. The application of 10% baking soda solution for 5 min may be an alternative pre-restorative treatment for bleached enamel, but further studies are needed to consider whether or not this treatment may be effectively used in clinical practice.

Application and properties of pure lime façades - case study

Directory of Open Access Journals (Sweden)

Violeta Bokan Bosiljkov

2008-01-01

Full Text Available The paper presents experiences obtained during application and testing of different pure lime façades that could be successfully used in restoration of historical buildings in Slovenia. The lime façade consists of a rendering layer (rough mortar, a finishing layer (fine mortar and a protective layer of lime wash. For the design of the mortars different industrially and traditionally produced limes were chosen, based on the results of preliminary studies of the authors and experiences of a small enterprise (SE involved in the study. The façade layers were applied to the most problematic northern wall of the historic chapel made from rubble masonry. The chapel belongs to the castle Crnelo, built at the end of the 17th century in the village Turnše, not far from Ljubljana, the capital of Slovenia. The façade layers were made by skilled workers of SE, with about one year time difference between application of rendering and finishing layers, and with a protective layer of coloured lime wash applied to one to three day old finishing layers. On the rendering layers, visual inspection, water absorption tests and determination of carbonation depth were carried out before subsequent finishing layers were applied. The same on-site tests were carried out also on finished façade layers. So far, parallel to the on-site tests, compressive and water absorption tests on prisms prepared from rough mortars were carried out in laboratory.

Effect of liming on the behaviour of 90Sr and 137Cs in a lake ecosystem

International Nuclear Information System (INIS)

Outola, Iisa; Rask, Martti

2011-01-01

Liming of lakes is considered one possible remedial action to reduce the accumulation of radionuclides into fish in the case of a radiological accident. These responses were tested in field conditions in a small acidified lake that was divided into two parts: one limed with CaCO 3 and the other half left as an unlimed control. The transfer of 90 Sr from water into fish decreased on average by 50% during the first year after liming. However, at the same time the 90 Sr concentration in water increased, reaching a maximum within 6 months after liming. Approximately 50% more 90 Sr was detected in water in the limed part of the lake than on control side during the first year. 90 Sr was most probably released from the sediment as the Ca concentration and pH of the water increased. As a result of these two processes, which counterbalanced each other (increased release of 90 Sr into water from sediment and decreased transfer of 90 Sr from water into fish), the 90 Sr concentration in fish did not notably differ between the limed and control sides of the lake. Liming may only be suitable as a remedial action if carried out immediately after a radiological accident, before significant amounts of radionuclides have been deposited in lake sediments. In the case of 137 Cs, the effect of liming was less pronounced. 137 Cs activity concentration in water increased in the first year by 20% and uptake by fish decreased by 20%. - Highlights: → Acidified lake was divided into two parts: one limed with CaCO 3 and the other half left as an unlimed control. → The transfer of 90 Sr from water into fish decreased by 50% during the first year after liming. → At the same time liming increased the 90 Sr concentration in the water by 50%. → The increased amount of 90 Sr in water is assumed to have originated from the lake sediments. → The 90 Sr concentration in fish remained relatively unchanged.

Genetic variation assessment of acid lime accessions collected from south of Iran using SSR and ISSR molecular markers.

Science.gov (United States)

Sharafi, Ata Allah; Abkenar, Asad Asadi; Sharafi, Ali; Masaeli, Mohammad

2016-01-01

Iran has a long history of acid lime cultivation and propagation. In this study, genetic variation in 28 acid lime accessions from five regions of south of Iran, and their relatedness with other 19 citrus cultivars were analyzed using Simple Sequence Repeat (SSR) and Inter-Simple Sequence Repeat (ISSR) molecular markers. Nine primers for SSR and nine ISSR primers were used for allele scoring. In total, 49 SSR and 131 ISSR polymorphic alleles were detected. Cluster analysis of SSR and ISSR data showed that most of the acid lime accessions (19 genotypes) have hybrid origin and genetically distance with nucellar of Mexican lime (9 genotypes). As nucellar of Mexican lime are susceptible to phytoplasma, these acid lime genotypes can be used to evaluate their tolerance against biotic constricts like lime "witches' broom disease".

The Effect of Kaffir Lime Leaves Distillation Residue Oleoresin Concentration on Active Paper Packaging Characteristics

Science.gov (United States)

Kawiji; Utami, R.; Ulum, S.; Khasanah, L. U.; Manuhara, G. J.; Atmaka, W.

2018-03-01

Oleoresin of kaffir lime leaves distillation residue still contains some active compounds such as Citronellal, β-Citronellol, and Linalool which potential to incorporated on the active paper packaging. The purposes of this study were to determine the effect of kaffir lime leaves distillation residue oleoresin concentration on the physical characteristics, sensory characteristics, and antimicrobial activity of the active paper packaging incorporated with kaffir lime leaves distillation residue oleoresin and to determine the functional groups of active paper packaging. The concentration of kaffir lime leaves distillation residue oleoresin were varied at 0%, 2%, 4% and 6%. The result showed that the addition of kaffir lime leaves distillation residue oleoresin increased the thickness and moisture content of the paper and decreased the tensile strengths and folding endurances of active paper packaging. The microbial inhibition tends to increase along with the higher oleoresin concentration addition. Aromatic CH group were found at a wavelength of 897.90 cm-1 of on paper packaging with 2% oleoresin indicated as functional aromatic functional group allegedly obtained from the kaffir lime leaves oleoresin.

Expansive soil stabilization with coir waste and lime for flexible pavement subgrade

Science.gov (United States)

Narendra Goud, G.; Hyma, A.; Shiva Chandra, V.; Sandhya Rani, R.

2018-03-01

Expansive soil properties can be improved by various methods to make it suitable for construction of flexible pavement. The coir pith is the by-product (bio-waste) generated from coir industry during extraction of coir fiber from coconut husk. Openly disposed coir pith can make the surrounding areas unhygienic. This bio-waste can be one of the potential materials to stabilize the expansive soils. In the present study coir pith and lime are used as stabilizers. Different combinations of coir pith contents (1%, 2% and 3%) and lime contents (2%, 3% and 4%)are used to study the behavior of expansive soil. Unconfined compressive strength (UCS) of unstabilized and stabilized soils was determined. Optimum content of coir pith and lime are determined based on UCS of the soil. California bearing ratio of soil determined at optimum contents of coir pith and lime. Flexible pavement layer compositions for two levels of traffic using stabilized soil subgrade.

Lime kiln dust as a potential raw material in portland cement manufacturing

Science.gov (United States)

Miller, M. Michael; Callaghan, Robert M.

2004-01-01

In the United States, the manufacture of portland cement involves burning in a rotary kiln a finely ground proportional mix of raw materials. The raw material mix provides the required chemical combination of calcium, silicon, aluminum, iron, and small amounts of other ingredients. The majority of calcium is supplied in the form of calcium carbonate usually from limestone. Other sources including waste materials or byproducts from other industries can be used to supply calcium (or lime, CaO), provided they have sufficiently high CaO content, have low magnesia content (less than 5 percent), and are competitive with limestone in terms of cost and adequacy of supply. In the United States, the lime industry produces large amounts of lime kiln dust (LKD), which is collected by dust control systems. This LKD may be a supplemental source of calcium for cement plants, if the lime and cement plants are located near enough to each other to make the arrangement economical.

Nutritional value of organic acid lime juice (Citrus latifolia T., cv. Tahiti

Directory of Open Access Journals (Sweden)

Carolina Netto Rangel

2011-12-01

Full Text Available Acid lime can be used as fresh fruit or as juice to increase the flavor of drinks. Therefore, it is necessary to analyze organic acid lime nutritional composition in order to evaluate if there are important differences among those conventionally produced. No significant differences in total titrable acidity, pH, ascorbic acid, sucrose, calcium, and zinc were found between the acid lime juice from organic biodynamic crops and conventional crops. However, the organic biodynamic fruits presented higher peel percentage than the conventional ones leading to lower juice yield. On the other hand, fructose, glucose, total soluble solids contents, potassium, manganese, iron, and copper were higher in the conventional samples. These results indicated few nutritional differences between organic and conventional acid lime juices in some constituents. Nevertheless, fruit juice from biodynamic crops could be a good choice since it is free from pesticides and other agents that cause problems to human health maintaining the levels similar to those of important nutritional compounds.

Dissolved organic carbon and nitrogen mineralization strongly affect co2 emissions following lime application to acidic soil

International Nuclear Information System (INIS)

Shaaban, M.; Peng, Q.; Lin, S.; Wu, Y.

2014-01-01

Emission of greenhouse gases from agricultural soils has main contribution to the climatic change and global warming. Dynamics of dissolved organic carbon (DOC) and nitrogen mineralization can affect CO/sub 2/ emission from soils. Influence of DOC and nitrogen mineralization on CO/sub 2/ emissions following lime application to acidic soil was investigated in current study. Laboratory experiment was conducted under aerobic conditions with 25% moisture contents (66% water-filled pore space) at 25 degree C in the dark conditions. Different treatments of lime were applied to acidic soil as follows: CK (control), L (low rate of lime: 0.2g lime / 100 g soil) and H (high rate of lime: 0.5g lime /100g soil). CO/sub 2/ emissions were measured by gas chromatography and dissolved organic carbon, NH4 +-N, NO/sub 3/ --N and soil pH were measured during incubation study. Addition of lime to acidic soil significantly increased the concentration of DOC and N mineralization rate. Higher concentrations of DOC and N mineralization, consequently, increased the CO/sub 2/ emissions from lime treated soils. Cumulative CO/sub 2/ emission was 75% and 71% higher from L and H treatments as compared to CK. The results of current study suggest that DOC and N mineralization are critical in controlling gaseous emissions of CO/sub 2/ from acidic soils following lime application. (author)

Crystalline ordered states of CuIn1−xGaxSe2 (x = 0, 0.3, and 1.0) thin-films on different substrates investigated by Raman scattering spectroscopy

International Nuclear Information System (INIS)

Jeong, A.R.; Jo, W.; Song, M.; Yoon, S.

2012-01-01

Structural properties of Cu(In,Ga)Se 2 absorber layers have been examined for photovoltaic applications. Thin-films with three different chemical compositions, CuInSe 2 (CIS), Cu(In,Ga)Se 2 (CIGS) and CuGaSe 2 (CGS), were grown by co-evaporation on two kinds of substrates: Mo-coated soda-lime glass and bare soda-lime glass. Intriguing morphology and grain-growth behaviors were found in the surface of the films. X-ray diffraction of the films exhibited phase formation of the stoichiometric chalcopyrite phase of the materials while signs of secondary phases like Cu 2 Se and Cu–Se 2 were also observed. The optical transmittance of the films was measured to obtain their optical bandgaps, which were well matched with the bulk values of CIS, CIGS, and CGS, which are 1.1, 1.4, and 1.7 eV, respectively. Using Raman scattering spectroscopy, the A 1 mode was observed to shift from 177 cm −1 for CIS to 189 cm −1 for CGS as the Ga content increased. The films on Mo substrates are likely to have secondary phases, which is not the case for soda-lime glass. An indication of the formation of the CuAu structure is obtained from the CIS thin-films. - Highlights: ► We report structural and optical properties of CIGS films on different substrates. ► Various optical tools were used to characterize the CIGS films. ► Crystalline ordered states were examined by A1 mode of Raman spectra.

Cytotoxic and antibacterial activity of the mixture of olive oil and lime cream in vitro conditions.

Science.gov (United States)

Sumer, Zeynep; Yildirim, Gulay; Sumer, Haldun; Yildirim, Sahin

2013-01-01

The mixture of olive oil and lime cream has been traditionally used to treat external burns in the region of Hatay/Antakya and middle Anatolia. Olive oil and lime cream have been employed by many physicians to treat many ailments in the past. A limited number of studies have shown the antibacterial effect of olive oil and that it does not have any toxic effect on the skin. But we did not find any reported studies on the mixture of olive oil and lime cream. The aim of this paper is to investigate the cytotoxic and antibacterial activity of olive oil and lime cream individually or/and in combination in vitro conditions, by using disk-diffusion method and in cell culture. The main purpose in using this mixture is usually to clear burns without a trace. Agar overlay, MTT (Cytotoxicity assay) and antibacterial susceptibility tests were used to investigate the cytotoxic and antibacterial activity of olive oil and lime cream. We found that lime cream has an antibacterial activity but also cytotoxic on the fibroblasts. On the other hand olive oil has limited or no antibacterial effect and it has little or no cytotoxic on the fibroblasts. When we combined lime cream and olive oil, olive oil reduced its cytotoxic impact. These results suggest that mixture of olive oil and lime cream is not cytotoxic and has antimicrobial activity.

Revisiting tropical instability wave variability in the Atlantic ocean using SODA reanalysis

Science.gov (United States)

de Decco, Hatsue Takanaca; Torres Junior, Audalio Rebelo; Pezzi, Luciano Ponzi; Landau, Luiz

2018-03-01

The spatial and temporal variability of energy exchange in Tropical Instability Waves (TIWs) in the Atlantic Ocean were investigated. A spectral analysis was used to filter the 5-day mean results from Simple Ocean Data Assimilation (SODA) reanalysis spanning from 1958 to 2008. TIWs were filtered over periods of 15 to 60 days and between wavelengths of 4 and 20 longitude degrees. The main approach of this study was the use of bidirectionally filtered TIW time series as the perturbation fields, and the difference in these time series from the SODA total results was considered to be the basic state for energetics analysis. The main result was that the annual cycle (period of 360 days) was the main source of variability of the waves, and the semi-annual cycle (period of 180 days) was a secondary variation, which indicated that TIWs occurred throughout the year but with intensity that varies seasonally. In SODA, barotropic instability acts as the mechanism that feeds and extracts energy to/from TIWs at equatorial Atlantic. Baroclinic instability is the main mechanism that extracts energy from TIWs to the equatorial circulation north of the Equator. All TIW patterns of variability were observed western of 10° W. The present study reveals new evidences regarding TIW variability and suggests that future investigations should include a detailed description of TIW dynamics as part of Atlantic Ocean equatorial circulation.

Prevalence of using baking soda in different types of most commonly consumed breads by Iranian people

OpenAIRE

Abolfazl Mohammadbeigi; Ali Salehi; Hassan Izanloo; Zahra Ghorbani; Vahid Vanaki; Reza Ramazani; Mahdi Asadi-Ghalhari

2018-01-01

Background: Nowadays, in most bakeries in order to accelerate bread production process and reduce work pressure on bakers, harmful chemicals like baking soda are in use. Therefore, the aim of the present study was to investigate the prevalence of using baking soda in different types of most commonly consumed breads by Iranian people. Materials and Methods: This cross-sectional descriptive study was carried out on 234 bakeries in Qom, Iran, during 2017. The proportional stratified sampling met...

Application of lime and urea and its effect on development of Phythophthora palmivora.

Directory of Open Access Journals (Sweden)

Sakti Widyanta Pratama

2015-03-01

Full Text Available Black pod rot disease (BPRD which is caused by Phytophthora palmivora is one of the main diseases of cocoa cultivations particularly in plantations with wet climate. Black pod rot can develop rapidly under high humidity environments, particularly during rainy seasons. This disease can cause loss of harvest of up to 46.63% in East Java. The various control efforts attempted so far have not resulted in significant improvements. Urea, in addition to functioning as fertilizer, can also produce the ammonia gas which is believed to be able to suppress black pod rot. This research aims to determine the effectiveness of black pod rot control using the combination of lime and urea. This research was conducted from June to September 2013. The materials used in test included sterile soil, black pod rot infected cocoa, urea, and agricultural lime. Observation results showed that ammonia could form from urea. Lime can increase the speed of the formation. The ammonia gas forming from 0.06% urea and 0.3% lime can control the P. palmivora fungus inside the soil. Key words: Pod rot, P. palmivora, urea, lime, ammonia

A systematic review of the effectiveness of liming to mitigate impacts of river acidification on fish and macro-invertebrates

International Nuclear Information System (INIS)

Mant, Rebecca C.; Jones, David L.; Reynolds, Brian; Ormerod, Steve J.; Pullin, Andrew S.

2013-01-01

The addition of calcium carbonate to catchments or watercourses – liming – has been used widely to mitigate freshwater acidification but the abatement of acidifying emissions has led to questions about its effectiveness and necessity. We conducted a systematic review and meta-analysis of the impact of liming streams and rivers on two key groups of river organisms: fish and invertebrates. On average, liming increased the abundance and richness of acid-sensitive invertebrates and increased overall fish abundance, but benefits were variable and not guaranteed in all rivers. Where B-A-C-I designs (before-after-control-impact) were used to reduce bias, there was evidence that liming decreased overall invertebrate abundance. This systematic review indicates that liming has the potential to mitigate the symptoms of acidification in some instances, but effects are mixed. Future studies should use robust designs to isolate recovery due to liming from decreasing acid deposition, and assess factors affecting liming outcomes. -- Highlights: •In a systematic review and meta-analysis, we asked how river liming affected fish and invertebrates. •On average, liming increased fish abundance. •Liming also increased average abundance and richness of acid-sensitive invertebrates. •However, benefits were variable and not guaranteed in all acidified rivers. -- A systematic review showed lime application to acidified rivers increased average fish abundance, and abundance and richness in acid-sensitive invertebrates, but not always

Influence of lime on struvite formation and nitrogen conservation during food waste composting.

Science.gov (United States)

Wang, Xuan; Selvam, Ammaiyappan; Wong, Jonathan W C

2016-10-01

This study aimed at investigating the feasibility of supplementing lime with struvite salts to reduce ammonia emission and salinity consequently to accelerate the compost maturity. Composting was performed in 20-L bench-scale reactors for 35days using artificial food waste mixed with sawdust at 1.2:1 (w/w dry basis), and Mg and P salts (MgO and K2HPO4, respectively). Nitrogen loss was significantly reduced from 44.3% to 27.4% during composting through struvite formation even with the addition of lime. Lime addition significantly reduced the salinity to less than 4mS/cm with a positive effect on improving compost maturity. Thus addition of both lime and struvite salts synergistically provide advantages to buffer the pH, reduce ammonia emission and salinity, and accelerate food waste composting. Copyright © 2016 Elsevier Ltd. All rights reserved.

Shear strength and compressibility behaviour of lime-treated organic clay

OpenAIRE

Yunus, NZM; Wanatowski, D; Hassan, NA; Marto, A

2016-01-01

Apart from strength characteristics, a review of studies on the compressibility of lime-treated soils is equally important that influenced the stability of soil structures. Due to the fact that no study has been carried out, an investigation on the effects of humic acid on strength and compressibility behaviour of lime-stabilised organic clay is presented in this paper. Unconfined Compressive Strength (UCS) and oedometer tests were carried out at different curing periods of 7, 28 and 90 days....

Nano Transition Metal Sulfide Catalyst for Solvolysis Liquefaction of Soda Lignin

International Nuclear Information System (INIS)

Fei-Ling, P.; Chin-Hua, C.; Sarani Zakaria; Soon-Keong, N.; Tze-Khong, L.

2011-01-01

Solvolysis liquefaction of soda lignin in the presence of various transition metal sulfide catalysts was studied to investigate the catalyst effects on the oil and gas yields, conversion rate and higher heating value (HHV) of oil. Nano sized copper sulfide, iron sulfide and molybdenum sulfide were successfully synthesized via a simple hydrothermal method under reaction temperature 200 degree Celsius for 90 min. The addition of transition metal sulfide based catalysts (CuS, MoS 2 and FeS 2 ) enhanced both production of the oils and gas and the higher heating value (HHV) of oil products. A high oil and gas yields of 82.1 % and 2890 cm 3 was obtained with MoS 2 at 250 degree Celsius for 60 min. Elemental analyses for the oils revealed that the liquid products have much higher heating values than the crude soda lignin powder. (author)

Briquetting soda weed (Salsola tragus) to be used as a rural fuel source

Energy Technology Data Exchange (ETDEWEB)

Yumak, Hasan [Mechanical Engineering Department, Faculty of Engineering and Architecture, Yuzuncu Yil University, 65080 Van (Turkey); Ucar, Tamer [Mechanical Engineering Department, Faculty of Engineering and Architecture, Bozok University, 66200 Yozgat (Turkey); Seyidbekiroglu, Nesim [Agricultural Machinery Department, Faculty of Agriculture, Yuzuncu Yil University, 65080 Van (Turkey)

2010-05-15

Amount of traditional fuel sources in the world has been decreasing and there is a definite need to produce and utilize alternative fuels such as biomass materials. In this study, briquetting conditions of Russian tumbleweed, Salsola tragus, (commonly named soda weed in Turkey) which grows in salty soils were investigated. Soda weeds were first chopped coarsely in a local tresher, then chopped finely in a hammer mill. Weed materials at three moisture levels (7%, 10%, and 13%) were prepared in the lab. Chopped weed materials were filled in cylindrical and square dies and compressed using a hydraulic press at three pressure levels of 15.7, 19.6 and 31.4 MPa. Optimum temperature, moisture rate, and pressure values were determined to produce stable briquettes. Further experiments were conducted to produce briquettes using sawdust and walnut shells as additives in conical dies of two different sizes. Results of a statistical analysis of parameters to produce briquettes in different dies indicated that moisture rates of 7-10%, pressure of 31.4 MPa, and temperatures of 85-105 C were suitable for briquetting soda weed. Furthermore, sawdust and walnut shells additives increased briquette density without any negative effects on production process and product stability. (author)

Effectiveness of lime and peat applications on cadmium availability in a paddy soil under various moisture regimes.

Science.gov (United States)

Chen, Yanhui; Xie, Tuanhui; Liang, Qiaofeng; Liu, Mengjiao; Zhao, Mingliu; Wang, Mingkuang; Wang, Guo

2016-04-01

In paddy soils, amendments and moisture play important role in the immobilization of cadmium (Cd). The effects of applying lime, peat, and a combination of both on soil Eh, pH, and Cd availability in contaminated soils were investigated under wetted (80 ± 5 % of water holding capacity) and flooded (completely submerged) conditions. In wetted soils, there was little change in Eh, compared to flooded soils where Eh reduced rapidly. Amendments of lime only or in a mixture with peat increased soil pH to different degrees, depending on the lime application rate. However, peat addition only slightly affected soil pH. The decreased Cd availability in flooded soils was related to submergence duration and was significantly lower than that in wetted soils after 14 days. Liming wetted and flooded soils decreased exchangeable Cd and increased carbonates or Fe-Mn oxides bound fractions, while peat addition transformed Cd from carbonates to organic matter bound fractions. The combined application of peat and lime generally showed better inhibitory effects on the availability of Cd than separately application of lime or peat. Higher application rates of lime, peat, or their mixture were more effective at reducing Cd contamination in flooded soil. This indicates that application of peat and lime mixture under flooded conditions was most effective for in situ remediation of Cd-contaminated soils. Further studies are required to assess the long-term effectiveness of the peat and lime mixture on Cd availability in paddy soils.

Lime application for the efficient production of nutraceutical glucooligosaccharides from Leuconostoc mesenteroides NRRL B-742 (ATCC13146).

Science.gov (United States)

Moon, Young Hwan; Madsen, Lee; Chung, Chang-Ho; Kim, Doman; Day, Donal F

2015-02-01

We have previously demonstrated the production of glucooligosaccharides via a fermentation of sucrose with Leuconostoc mesenteroides NRRL B-742 using sodium hydroxide (NaOH) to control the pH. Because NaOH is expensive, we sought to minimize the cost of our process by substituting hydrated lime and saccharate of lime (lime sucrate) in its place. The yield of glucooligosaccharides using either 5 % lime (41.4 ± 0.5 g/100 g) or 5 % lime sucrate (40.0 ± 1.4 g/100 g) were both similar to the NaOH control (42.4 ± 1.5 g/100 g). Based on this, it appears that the cost associated with pH control in our process can be reduced by a factor of approximately 2.4 using lime instead of NaOH. Because our chromatographic stage is based on a Ca(2+)-form resin to separate glucooligosaccharides, the use of lime not only negates the need for costly de-salting via ion-exchange (elimination of two ion-exchange sections) prior to separation, but also greatly reduces the resin regeneration cost.

Thermophysical properties of enzyme clarified Lime (Citrus aurantifolia L) juice at different moisture contents.

Science.gov (United States)

Manjunatha, S S; Raju, P S; Bawa, A S

2014-11-01

Thermophysical properties of enzyme clarified lime (Citrus aurantifolia L.) juice were evaluated at different moisture contents ranging from 30.37 % to 89.30 % (wet basis) corresponding to a water activity range of 0.835 to 0.979. The thermophysical properties evaluated were density, Newtonian viscosity, thermal conductivity, specific heat and thermal diffusivity. The investigation showed that density and Newtonian viscosity of enzyme clarified lime juice decreased significantly (p lime juice with moisture content/water activity employing regression analysis by the method of least square approximation. Results indicated the existence of strong correlation between thermophysical properties and moisture content/water activity of enzyme clarified lime juice, a significant (p < 0.0001) negative correlation between physical and thermal properties was observed.

Effects of liming on forage availability and nutrient content in a forest impacted by acid rain.

Directory of Open Access Journals (Sweden)

Sarah E Pabian

Full Text Available Acidic deposition and subsequent forest soil acidification and nutrient depletion can affect negatively the growth, health and nutrient content of vegetation, potentially limiting the availability and nutrient content of forage for white-tailed deer (Odocoileus virginianus and other forest herbivores. Liming is a mitigation technique that can be used to restore forest health in acidified areas, but little is known about how it affects the growth or nutrient content of deer forage. We examined the effects of dolomitic limestone application on the growth and chemical composition of understory plants in an acidified forest in central Pennsylvania, with a focus on vegetative groups included as white-tailed deer forage. We used a Before-After-Control-Impact study design with observations 1 year before liming and up to 5 years post-liming on 2 treated and 2 untreated 100-ha sites. Before liming, forage availability and several nutrients were below levels considered optimal for white-tailed deer, and many vegetative characteristics were related to soil chemistry. We observed a positive effect of liming on forb biomass, with a 2.7 fold increase on limed sites, but no biomass response in other vegetation groups. We observed positive effects of liming on calcium and magnesium content and negative effects on aluminum and manganese content of several plant groups. Responses to liming by forbs and plant nutrients show promise for improving vegetation health and forage quality and quantity for deer.

Influence of the mechanical properties of lime mortar on the strength of brick masonry

OpenAIRE

PAVIA, SARA

2013-01-01

PUBLISHED This paper aims at improving the quality of lime mortar masonry by understanding the mechanics of mortars and masonry and their interaction. It investigates how the mortar?s compressive and flexural strengths impact the compressive and bond strength of clay brick masonry bound with calcium lime (CL) and natural hydraulic lime (NHL) mortars. It concludes that the strength of the bond has a greater impact on the compressive strength of masonry than the mortar?s st...

Estimation of atmospheric fluoride by limed filter papers

International Nuclear Information System (INIS)

Smith, D.R.

1988-09-01

The limed filter paper method of static sampling of atmospheric fluoride is reviewed in this report. Use of the technique, in conjunction with precise measurement of the absorbed fluoride and calibration with dynamic air sampling techniques, to estimate atmospheric fluoride levels, is considered to give only qualitative data (± 50%). The limed filter paper method is site specific due to variations in meteorological conditions. Its main value is to indicate seasonal and annual trends in fluoride exposure of vegetation. Subject to these considerations, the lower and upper limits of atmospheric fluoride exposure and the applicability to atmospheric fluoride estimation under routine or emergency fluoride release conditions are discussed, with special emphasis on the limiting factors

A comparative study of the effect of diet and soda carbonated drinks ...

African Journals Online (AJOL)

EB

2013-09-03

Sep 3, 2013 ... Objectives: A comparative effect of the diet and regular soda carbonated drinks on the histology of the cerebellum of ... contains caffeine, depending on the quantities .... and health: a systematic review and meta-analysis.

Obtaining a glass-ceramic material from a steel slag mixed with glass cullet; Obtencion de un material vitroceramico a partir de una escoria de aceria mezclada con vidrio de desecho

Energy Technology Data Exchange (ETDEWEB)

Oziel Mendez Guerrero, D.; Alicia Vazquez Mendez, B.; Alvarez Mendez, A.

2011-07-01

In this paper, the qualitative, quantitative and thermal characterization of a steel slag and glass cullet of high generation rate in northern Mexico were made in order to use these wastes as raw materials in the production of glass ceramics. The particle size was controlled at sizes = 75 micrometers and the major components of the slag were located in a phase equilibrium diagram for proposing a reaction temperature that leaded to the starting glass. Later, heat treatments were performed to obtain the glass ceramics. The materials were characterized by powder X-ray diffraction (XRD), differential thermal analysis coupled with thermal gravimetric analysis (DTA-TGA), reflected light optical microscopy (RLOM) and scanning electron microscopy (SEM). Subsequently, Vickers microhardness and chemical resistance tests were performed, which enabled us to propose an application of the glass ceramics. (Author) 18 refs.

Effects of acid rain and liming on the enchytraeid fauna in forest soils

International Nuclear Information System (INIS)

Graefe, U.

1989-01-01

The development of the enchytraeid community has been observed in a Solling beech forest over a period of 11 years. Eight out of 18 formerly established species have disappeared in one decade. The connection to soil chemical changes due to atmospheric deposition is discussed. A comparison of adjoining beech and spruce stands revealed considerably lower species numbers under spruce. The community under beech is developing in the direction of the species community in the spruce stand. Liming affects changes in the dominance structure. Mesophilic species are favoured, acidophilic are repressed. In an oak-beech stand near Hamburg even the recolonization by previously absent species was observed. Liming experiments with 25, 50 and 100 dt CaCO 3 /ha showed decreasing total abundance of enchytraeids proportional to the amount of lime. Species number, diversity and evenness increased with lime treatments up to 50 dt/ha. (orig.)

Subgrade stabilization alternatives to lime and cement.

Science.gov (United States)

2010-04-15

This project involved four distinct research activities, (1) the influence of temperature on lime-stabilized soils, (2) the influence of temperature on cement-stabilized soils (3) temperature modeling of stabilized subgrade and (4) use of calcium chl...

Solidification of radioactive waste in a cement/lime mixture

International Nuclear Information System (INIS)

Zhou, H.; Colombo, P.

1984-01-01

The suitability of a cement/lime mixture for use as a solidification agent for different types of wastes was investigated. This work includes studies directed towards determining the wasted/binder compositional field over which successful solidification occurs with various wastes and the measurement of some of the waste from properties relevant to evaluating the potential for the release of radionuclides to the environment. In this study, four types of low-level radioactive wastes were simulated for incorporation into a cement/lime mixture. These were boric acid waste, sodium sulfate wastes, aion exchange resins and incinerator ash. 7 references, 3 figures, 2 tables

Evaluation of lime and hydrothermal pretreatments for efficient enzymatic hydrolysis of raw sugarcane bagasse.

Science.gov (United States)

Grimaldi, Maira Prearo; Marques, Marina Paganini; Laluce, Cecília; Cilli, Eduardo Maffud; Sponchiado, Sandra Regina Pombeiro

2015-01-01

Ethanol production from sugarcane bagasse requires a pretreatment step to disrupt the cellulose-hemicellulose-lignin complex and to increase biomass digestibility, thus allowing the obtaining of high yields of fermentable sugars for the subsequent fermentation. Hydrothermal and lime pretreatments have emerged as effective methods in preparing the lignocellulosic biomass for bioconversion. These pretreatments are advantageous because they can be performed under mild temperature and pressure conditions, resulting in less sugar degradation compared with other pretreatments, and also are cost-effective and environmentally sustainable. In this study, we evaluated the effect of these pretreatments on the efficiency of enzymatic hydrolysis of raw sugarcane bagasse obtained directly from mill without prior screening. In addition, we evaluated the structure and composition modifications of this bagasse after lime and hydrothermal pretreatments. The highest cellulose hydrolysis rate (70 % digestion) was obtained for raw sugarcane bagasse pretreated with lime [0.1 g Ca(OH)2/g raw] for 60 min at 120 °C compared with hydrothermally pretreated bagasse (21 % digestion) under the same time and temperature conditions. Chemical composition analyses showed that the lime pretreatment of bagasse promoted high solubilization of lignin (30 %) and hemicellulose (5 %) accompanied by a cellulose accumulation (11 %). Analysis of pretreated bagasse structure revealed that lime pretreatment caused considerable damage to the bagasse fibers, including rupture of the cell wall, exposing the cellulose-rich areas to enzymatic action. We showed that lime pretreatment is effective in improving enzymatic digestibility of raw sugarcane bagasse, even at low lime loading and over a short pretreatment period. It was also demonstrated that this pretreatment caused alterations in the structure and composition of raw bagasse, which had a pronounced effect on the enzymes accessibility to the

Liming effect on P availability from Maardu phosphate rock

International Nuclear Information System (INIS)

Sidlauskas, G.; Masauskas, S.; Ezerinskas, V.

2002-01-01

Thirty years ago phosphate rock from the Maardu deposit was intensively used for soil fertilization in Lithuania. However, the application of finely ground product caused an undesirable dusty operation. Afterwards, a super-phosphate production plant was built in Kedainiai and the use of phosphate rock was completely abandoned. Field experiments with fodder beets and barley were carried out to evaluate the P availability of granulated superphosphate and Maardu phosphate rock. The comparison was made at three acidity levels: a) unlimed acid soil with a high content of Al (pH kcl 4.3-4.4, hydrolytic acidity was 41-44 meq/kg soil), b) soil limed with 0.5n rate CaCO 3 powder limestone based on hydrolytic acidity, and c) soil limed with 1.0n rate CaCO 3 . Two field experiments were carried out with fodder beets. In 1997 the yield increased significantly due to liming. However, no significant yield increases were found due to the application of phosphorus fertilizers. Differences between the effect of superphosphate and phosphate rock were also not observed. This might have been caused by a severe drought during the vegetative growth of plants. In the following year, 1998, a soil with similar acidity was chosen, however it contained even lower amounts of available phosphorus in the arable soil (about 50 mg/kg soil A-L method). In the unlimed soil the yield was low, the effect of superphosphate was better than that of phosphate rock. A good fodder beet yield of 32 to 35 t/ha was obtained and the effect of phosphate rock was better than that of superphosphate at 0.5n CaCO 3 rate. When liming with at the high rate (1.0n CaCO 3 rate according to hydrolytic acidity) the action of phosphate rock declined, and a better yield was obtained with superphosphate. Barley was grown after fodder beets in the 1997 experimental field and the residual effect of superphosphate and phosphate rock was investigated. Weather conditions were favorable for barley growth. Therefore a normal yield

Geomechanical properties of lime stabilized clayey sands

International Nuclear Information System (INIS)

Arabani, M.; Karami, M. Veis

2007-01-01

Clayey sands that have low plasticity, low compressibility and high strength under loads, are suitable as a base material for any engineering construction projects as well as for roads and building construction. Decrease of plasticity and compressibility as well as increase in strength of these materials can be obtained by many different methods. Of these methods, lime stabilization is a common, applicable, and easy to use approach that can improve geomechanical and geotechnical properties of clayey sand fills. In this study some important geomechanical properties and geotechnical properties of clayey sands including compressive strength, CBR and elastic plastic behavior are investigated. A range of gradations representative of those gradations found in situ in the north of Iran were selected for testing and samples were artificially rebuilt in the laboratory. The mixes were then stabilized with hydrated lime and cured. Different mechanical tests were performed on mature materials. The stress-strain behavior of lime-stabilized mixes was plotted and a parabolic function was used to estimate the trend of stress-strain behavior. The data show that there is a correlation among the results of uniaxial load test, tensile strength, and CBR of the tested specimens. Also, results of the unconfined compression test and the indirect tensile strength test show that an increase in clay content up to a certain percent, in the clay-sand fills, tends to increase the strength of the materials in compression as well as in tension. (author)

Download this PDF file

African Journals Online (AJOL)

adsorbent, anhydrous calcium chloride" and a pre-weighed carbon dioxide adsorbent, soda lime. Glycerol was identified spectroscopically (IR) and by its reaction with KHSO, toform acrolein'. Kinetic analysis of data. The measured gas volumes were converted to moles of gas assuming ideal gas behaviour and correcting.

Maintaining of the demineralized water quality in storage tanks

International Nuclear Information System (INIS)

Hochmueller, K.; Wandelt, E.

1981-03-01

Two processes for maintaining the quality of the mineralized water in storage tanks are considered. A slight overpressure of nitrogen can be created above the water, or the air flowing in the tank can be cleaned by passing it through a soda-containing lime filter [fr

Design philosophy and construction of a high concentration compound parabolic concentrator

CSIR Research Space (South Africa)

Roos, TH

2010-09-01

Full Text Available mm samples were measured in a Cary spectrophotometer. The mean transmission of these samples is shown in comparison to a regular 2mm soda-lime glass sample (non-mirror application) from PFG in figure 2 (left). 400 600 800 1000 1200 1400 1600 1800...

Industrial Wastes as Auxiliary Additives to Cement/Lime Stabilization of Soils

OpenAIRE

James, Jijo; Pandian, P. Kasinatha

2016-01-01

Chemical stabilization involves the use of chemical agents for initiating reactions within the soil for modification of its geotechnical properties. Cement and lime stabilization have been the most common stabilization methods adopted for soil treatment. Cement stabilization results in good compressive strengths and is preferred for cohesionless to moderately cohesive soil but loses effectiveness when the soil is highly plastic. Lime stabilization is the most preferred method for plastic clay...

Real-time visualization of dynamic particle contact failures

Energy Technology Data Exchange (ETDEWEB)

Parab, Niranjan D.; Hudspeth, Matthew; Claus, Ben; Guo, Zherui; Sun, Tao; Fezzaa, Kamel; Chen, Weinong W.

2017-01-01

Granular materials are widely used to resist impact and blast. Under these dynamic loadings, the constituent particles in the granular system fracture. To study the fracture mechanisms in brittle particles under dynamic compressive loading, a high speed X-ray phase contrast imaging setup was synchronized with a Kolsky bar apparatus. Controlled compressive loading was applied on two contacting particles using the Kolsky bar apparatus and fracture process was captured using the high speed X-ray imaging setup. Five different particles were investigated: soda-lime glass, polycrystalline silica (silicon dioxide), polycrystalline silicon, barium titanate glass, and yttrium stabilized zirconia. For both soda lime glass and polycrystalline silica particles, one of the particles fragmented explosively, thus breaking into many small pieces. For Silicon and barium titanate glass particles, a finite number of cracks were observed in one of the particles causing it to fracture. For yttrium stabilized zirconia particles, a single meridonial crack developed in one of the particles, breaking it into two parts.

Studying the Environmental Health Status and Consumption of Baking Soda in Military and Urban Lavash Bakeries of Tehran in 2012

Directory of Open Access Journals (Sweden)

H Rostami

2013-06-01

Full Text Available Background and purpose:Consumption of baking soda, as a primary material for preparation of bread dough, has been banned due to its health complications in Iran. So bread production in our country faced difficulties and one part of them is related to health issues which are bread production. Also, in some cases, baking soda is used in the bread production. This study was done to study the environmental health status and consumption of baking soda in the military and urban Lavash bakeries of Tehran in 2012. Materials and methods:This is a descriptive comparative study done on Lavash bread production of 14 military bakeries and 14 corresponding urban bakeries near them. PH in the samples was tested based on Institute of Standards and Industrial Research of Iran No. 2628. To check the status of environmental health and personal hygiene of bakeries, the check list of Cereal Research Center was used. Results:In terms of environmental health status,28.6% military bakeries and7.1% urban bakeries were at good level. In terms of personal hygiene, all bakeries were in the poor category. Also,42.9% of military Lavash bakeries and 14.3% of urban Lavash bakeries used baking soda in their bread production. Conclusion:Environment health and personal hygiene status in military bakeries are better than the urban bakeries however, hygiene status was not desirable in military bakeries. Also, baking soda consumption in military bakeries was more common than the urban bakeries. According to the results of this study, control of health status and avoiding baking soda consumption in the bakeries are necessary.

Shift in aggregation, ROS generation, antioxidative defense, lysozyme and acetylcholinesterase activities in the cells of an Indian freshwater sponge exposed to washing soda (sodium carbonate).

Science.gov (United States)

Mukherjee, Soumalya; Ray, Mitali; Ray, Sajal

2016-09-01

Washing soda, chemically identified as anhydrous sodium carbonate, is a popular cleaning agent among the rural and urban populations of India which often contaminates the freshwater ponds and lakes, the natural habitat of sponge Eunapius carteri. Present investigation deals with estimation of cellular aggregation, generation of ROS and activities of antioxidant enzymes, lysozyme and acetylcholinesterase in the cells of E. carteri under the environmentally realistic concentrations of washing soda. Prolonged treatment of washing soda inhibited the degree of cellular aggregation. Experimental exposure of 8 and 16mg/l of sodium carbonate for 48h elevated the physiological level of reactive oxygen species (ROS) generation in the agranulocytes, semigranulocytes and granulocytes of E. carteri, whereas, treatment of 192h inhibited the ROS generation in three cellular morphotypes. Activities of superoxide dismutase, catalase and glutathione-S-transferase were recorded to be inhibited under prolonged exposure of washing soda. Washing soda mediated inhibition of ROS generation and depletion in the activities of antioxidant enzymes were indicative to an undesirable shift in cytotoxic status and antioxidative defense in E. carteri. Inhibition in the activity of lysozyme under the treatment of sodium carbonate was suggestive to a severe impairment of the innate immunological efficiency of E. carteri distributed in the washing soda contaminated habitat. Washing soda mediated inhibition in the activity of acetylcholinesterase indicated its neurotoxicity in E. carteri. Washing soda, a reported environmental contaminant, affected adversely the immunophysiological status of E. carteri with reference to cellular aggregation, oxidative stress, antioxidative defense, lysozyme and acetylcholinesterase activity. Copyright © 2016 Elsevier Inc. All rights reserved.

Geotechnical and Physico-Chemical Characterization of Low Lime Fly Ashes

Directory of Open Access Journals (Sweden)

Arif Ali Baig Moghal

2013-01-01

Full Text Available In order to explore the possibility of using low-lime fly ashes, the physical and chemical properties which have a direct bearing on their geotechnical and geoenvironmental behaviors have been investigated. In this paper, two types of low-lime fly ashes, originating from India, have been used. A brief account of various methods adopted in characterizing their physical, chemical, and geotechnical properties is presented. The relative importance of each of these properties in enhancing the bulk applicability of fly ashes has been brought out.

The characteristics of soda metasomatite type uranium mineralization for proterozoic strata in the central-southern part of Kang-Dian earth's axis

International Nuclear Information System (INIS)

Qian Farong

1995-12-01

The uranium mineralization for Proterozoic strata in the central-southern part of Kang-Dian earth's axis can be divided into four typy (sandstone, soda metasomatite, proterozoic epimetamorphics and quartzite). The soda metasomatite type is the dominant type of uranium mineralization and has the prospecting potential in the area. The characteristics of this type uranium mineralization and the problems of metallogenesis are discussed. Soda metasomatite type uranium mineralization is controlled by soda metasomatite and structure. Uranium exists mainly in the forms of minerals (pitchblende, uranate). Its cell parameter is high and oxygenated coefficient is low, belonging to moderate-low temperature hydrothermal origin. The metallogenetic materials originated from deep-seated crust and country rocks. The metallogenetic solution includes a great quantity of atmospheric water, besides hydrothermal solution from deep-seated crust. The metallogene underwent the two stages i.e. Jinnin and Chengjiang. (4 tabs., 3 figs.)

Location of quarries of magnesian lime used as raw material of Roman plasters in western Lombardy (Italy

Directory of Open Access Journals (Sweden)

Roberto Bugini

2017-01-01

Full Text Available Lime as building material was widely diffused in Roman architecture of western Lombardy. The presence of magnesite (magnesium carbonate was detected in painted plasters coming from roman sites of Milano: magnesite indicates the use of dolomite to make the lime. Dolomite rocks widely outcrop in the Lombard Prealps: light grey dolomites and dolomitic limestones (Dolomia del Salvatore, Ladinian-Anisian; grey dolomites, sometimes with cyclothemes (Dolomia Principale, Norian. There is no evidence of Roman lime quarries or kilns in this area; the Romans probably exploited the same dolomite outcrops, located along the eastern shore of lake Maggiore, where lime was produced from the Middle Ages onwards. The glacio-fluvial deposits of the middle course of the river Adda (cobbles, pebbles of siliceous limestone together with limestone and dolomite outcropping in the river basin were another medieval and modern source of raw material, mainly to make a moderately hydraulic lime (called “calce forte”, but this kind of lime is lacking in Roman plasters.

Effects of Lime and Concrete Waste on Vadose Zone Carbon Cycling

DEFF Research Database (Denmark)

Thaysen, Eike Marie; Jessen, Søren; Postma, D.

2014-01-01

In this work we investigate how lime and crushed concrete waste (CCW) affect carbon cycling in the vadose zone and explore whether these amendments could be employed to mitigate climate change by increasing the transport of CO2 from the atmosphere to the groundwater. We use a combination of exper......In this work we investigate how lime and crushed concrete waste (CCW) affect carbon cycling in the vadose zone and explore whether these amendments could be employed to mitigate climate change by increasing the transport of CO2 from the atmosphere to the groundwater. We use a combination...... of experimental and modeling tools to determine ongoing biogeochemical processes. Our results demonstrate that lime and CCW amendments to acid soil contribute to the climate forcing by largely increasing the soil CO2 efflux to the atmosphere. In a series of mesocosm experiments, with barley (Hordeum vulgare L.......) grown on podzolic soil material, we have investigated inorganic carbon cycling through the gaseous and liquid phases and how it is affected by different soil amendments. The mesocosm amendments comprised the addition of 0, 9.6, or 21.2 kg m−2 of crushed concrete waste (CCW) or 1 kg lime m−2. The CCW...

Environment-Friendly Control of Pear Scab and Rust Using Lime Sulfur

Directory of Open Access Journals (Sweden)

Ju Hoon Cha

2018-03-01

Full Text Available Pear scab and rust are the major diseases causing severe epidemics in organic cultivation of pear trees. Incidences of pear scab and rust were compared in organically managed plots and conventionally managed plots to obtain optimum application schedule of environment-friendly control agents in organically managed plots. Organically cultural practice with 10 time-applications of lime sulfur and Bordeaux mixture showed higher than 40% of control efficacies of pear scab and rust compared to conventionally cultural practice. Organically cultural practice with 8 time-applications of lime sulfur considering weather condition showed higher than 30% of control efficacies of pear scab compared to conventionally cultural practice. The results suggest that proper application of environment-friendly control agents such as lime sulfur considering weather condition will enable effective control of the major diseases for organic cultivation of pear.

Effect of dentifrice containing fluoride and/or baking soda on enamel demineralization/remineralization: an in situ study.

Science.gov (United States)

Cury, J A; Hashizume, L N; Del Bel Cury, A A; Tabchoury, C P

2001-01-01

The additive effect of baking soda on the anticariogenic effect of fluoride dentifrice is not well established. To evaluate it, a crossover in situ study was done in three phases of 28 days. Volunteers, using acrylic palatal appliances containing four human enamel blocks, two sound (to evaluate demineralization) and two with artificial caries lesions (to evaluate remineralization), took part in this study. During each phase, 10% sucrose solution was dripped (3 times a day) only onto the sound blocks. After 10 min, a slurry of placebo, fluoride (F) or fluoride and baking soda (F+NaHCO(3)) dentifrice was dripped onto all enamel blocks. The results showed a higher F concentration in dental plaque formed during treatment with F+NaHCO(3) than placebo (pbaking soda neither improves nor impairs the effect of F dentifrice on reduction of demineralization and enhancement of remineralization of enamel.

Morphological alteration, lysosomal membrane fragility and apoptosis of the cells of Indian freshwater sponge exposed to washing soda (sodium carbonate).

Science.gov (United States)

Mukherjee, Soumalya; Ray, Mitali; Dutta, Manab Kumar; Acharya, Avanti; Mukhopadhyay, Sandip Kumar; Ray, Sajal

2015-12-01

Washing soda is chemically known as sodium carbonate and is a component of laundry detergent. Domestic effluent, drain water and various anthropogenic activities have been identified as major routes of sodium carbonate contamination of the freshwater ecosystem. The freshwater sponge, Eunapius carteri, bears ecological and evolutionary significance and is considered as a bioresource in aquatic ecosystems. The present study involves estimation of morphological damage, lysosomal membrane integrity, activity of phosphatases and apoptosis in the cells of E. carteri under the environmentally realistic concentrations of washing soda. Exposure to washing soda resulted in severe morphological alterations and damages in cells of E. carteri. Fragility and destabilization of lysosomal membranes of E. carteri under the sublethal exposure was indicative to toxin induced physiological stress in sponge. Prolonged exposure to sodium carbonate resulted a reduction in the activity of acid and alkaline phosphatases in the cells of E. carteri. Experimental concentration of 8 mg/l of washing soda for 192 h yielded an increase in the physiological level of cellular apoptosis among the semigranulocytes and granulocytes of E. carteri, which was suggestive to possible shift in apoptosis mediated immunoprotection. The results were indicative of an undesirable shift in the immune status of sponge. Contamination of the freshwater aquifers by washing soda thus poses an alarming ecotoxicological threat to sponges. Copyright © 2015 Elsevier Inc. All rights reserved.

Effect of quick lime on physicochemical properties of clay soil

Directory of Open Access Journals (Sweden)

Bessaim Mohammed Mustapha

2018-01-01

Full Text Available Clay soils are known for their water sensitivity, which causes irreparable damage to any structure built on this type of soil. In order to avoid such problem, it is necessary to use various improvement and stabilization methods such as treatment with lime. This process has been used successfully in the field for decades. The addition of lime generates various physicochemical reactions within the soil such as cation exchange and pozzolanic reactions which are largely responsible for the improvement of the soil in question. This paper presents a study concerning the variation of physicochemical properties of clayey soil with the addition of quicklime at different percentages. Experiments were performed on two clayey soils (CL type in order to investigate the influence of quicklime on Atterberg limits and pH. These tests were carried out in an attempt to study and follow the development and progression of various reactions occurred within the soil with various lime percentages. The results show that the addition of quicklime causes a significant improvement in soil properties by reducing plasticity and thereby improves the soil workability. It can also be found that the addition of lime increase pH of soil, which allow activating pozzolanic reactions who tend to stabilize the soil in question by formation of cementitious compounds. Finally, the pH can be considered as a relevant parameter who allows a better understanding of the reactions that occur in the soil matrix.

Comparative studies on anthraquinone retention following the soda/anthraquinone process using 14C-labelled anthraquinone, and mode of action of anthraquinone on lignins and lignin model components

International Nuclear Information System (INIS)

Pfuetze, E.

1982-01-01

This dissertation contributes to the clarification of the following questions: how much of the additive is retained in cellulose following soda/anthraquinone-wood pulping; how much anthraquinone can be detected after extraction studies and after a conventional CEHD-bleaching treatment; can differences be detected between soda lignins and soda/anthraquinone lignins with respect to analytical data, spectroscopie characteristics and macromolecular properties; and how do dimeric lignin models with #betta#-arylether structure behave in decomposition studies using the soda/anthraquinone process. (orig./MG) [de

Effect of Lime Addition Methods on Performance Related Properties of Asphalt Concrete Mixture

Directory of Open Access Journals (Sweden)

Amjad Hamd Khalil Albayati

2016-09-01

Full Text Available In the recent years, some of the newly constructed asphalt concrete pavements in Baghdad as well as other cities across Iraq showed premature failures with consequential negative impact on both roadway safety and economy. Frequently, load associated mode of failure (rutting and fatigue as well as, occasionally, moisture damage in some poorly drained sections are the main failure types found in those newly constructed road. In this research, hydrated lime was introduced into asphalt concrete mixtures of wearing course in two methods. The first one was the addition of dry lime on dry aggregate and the second one was the addition of dry lime on saturated surface dry aggregate moisturized by 2.0 to 3.0 percent of water. For each type of addition, five different percentages of lime as a partial replacement of ordinary limestone mineral filler were used; these were; 1.0, 1.5, 2.0, 2.5, and 3 percent by weight of aggregate besides a control mixture that did not contain lime. Marshall Mix design method was used and the performance properties of moisture damage, resilient modulus, permanent deformation and fatigue characteristics were evaluated using indirect tensile strength, uniaxial repeated loading and repeated flexural beam tests. Also, VESYS5W software was implemented to evaluate the pavements performance in terms of rut depth and fatigue area for a typical pavement structure. The main conclusion withdrawn from this research revealed that the use of 2.5 percent hydrated lime in dry addition method and wet addition method showed an improved fatigue and permanent deformation characteristics, lower moisture susceptibility and high resilient modulus.

The growth of Scots pine and the availability of nutrients in old Finnish liming experiments on drained peatlands

International Nuclear Information System (INIS)

Nieminen, M.; Paetilae, A.

1994-01-01

Liming (with applications of 1000 to 8000 kg/ha) had no long- term (1929-1985) effect on the growth of Scots pine on drained oligotrophic peatlands. Liming plus NPK fertilization had a variable effect on the growth of stands. The same treatment could result in a very different response in different experimental areas. Both liming alone and liming plus NPK fertilization increased the calcium, magnesium and nitrogen contents of peat and decreased the C/Nratio and acidity. Liming plus fertilization decreased needle boron and manganese and increased calcium and nitrogen concentrations. The results of peat and needle analysis indicated that the changes in nitrogen availability to trees caused by liming have not been sufficient enough to affect tree growth. It was also concluded that boron deficiency was the main reason for the lowered yield. (26 refs., 6 tabs., 8 figs.) (author)

Lime Stabilization of Fine-Grained Greenlandic Sediments in Relation to Construction Projects

DEFF Research Database (Denmark)

Jørgensen, Anders Stuhr; Ingeman-Nielsen, Thomas; Nielsen, Hans Rasmus

2010-01-01

to the cold climate, and it is therefore of great interest to study possible methods to improve the stability of the fine-grained sediments. This presentation will include results of laboratory studies of lime stabilization on a clay soil from Kangerlussuaq, western Greenland. The result includes tests...... of the optimum lime mixture in relation to both reaction time and temperature influence....

Determination of optimal burning temperature ranges for production of natural hydraulic limes

Czech Academy of Sciences Publication Activity Database

Válek, Jan; van Halem, Eveline; Viani, Alberto; Pérez-Estébanez, Marta; Ševčík, Radek; Šašek, Petr

2014-01-01

Roč. 66, September (2014), s. 771-780 ISSN 0950-0618 R&D Projects: GA MK(CZ) DF11P01OVV010 Keywords : natural hydraulic lime * mechanical properties * calcination * CaO * X-ray diffraction * lime reactivity Subject RIV: AL - Art, Architecture, Cultural Heritage Impact factor: 2.296, year: 2014 http://www.sciencedirect.com/science/article/pii/S095006181400628X

RELATIONSHIP BETWEEN CRYSTALLINE STRUCTURE AND OPTICAL PROPERTIES OF WHEAT (Triticum aestevum L. STRAW SODA-OXYGEN PULP

Directory of Open Access Journals (Sweden)

Esat Gümüşkaya

2003-04-01

Full Text Available In this study; pulp was produced with soda-oxygen process by using wheat (Triticum aestevum L. straw as raw material and this pulp bleached with hypocholoride (H and peroxyde (P stages. It was found that crystalline properties of unbleached and bleached pulp samples increased by removing amorphous components. In addition, paper sheets made from unbleached and bleached soda-oxygen pulp and determined their optical properties. Consequently; while crystalline properties of pulp samples was rising with HP bleaching, it was determined that optical properties of paper sheets improved with bleaching.

The geotechnical properties of black cotton soil treated with crushed ...

African Journals Online (AJOL)

From these tests, cohesion was found to be decreasing with increase in glass cullet content and the angle of internal friction increases as the glass cullet content increased. The Unconfined Compressive Strength test (UCS), permeability test and California Bearing Ratio test (CBR) increases as glass cullet content increased ...

Soil acidification and liming in grassland production and grassland soil fertility in Slovenia

Directory of Open Access Journals (Sweden)

Jure ČOP

2015-12-01

Full Text Available This paper reviews the evidences on grassland soil acidity and liming in relation to soil processes and herbage production. There is also an outline of the present state of soil acidity and acidity-related traits – contents of organic matter (OM, phosphorus (P and potassium (K in Slovene grassland. In grassland, soil acidification is an ongoing process under humid climate conditions. It is mainly driven by leaching of nutrients, net loss of cations due to retention in livestock products, use of physiologically acid fertilizers, acid rain and N2 fixation. This process is reduced by strong pH buffering capacity of the soil and by physiologically basic fertilizers. Acid grassland soils in Slovenia are widely distributed in spite of the fact that 44% of the total land has developed from a carbonate parent material. Of the 1713 grassland soil samples analysed during 2005-2007 45% were regarded as acid ones (pH < 5.5; in KCl, 57% as soils with very low P status (˂ 6 mg P2O5/100 g soil and 22% as soils with very low K status (˂ 10 mg K2O/100 soil. Increased content of soil organic matter was identified for alpine pastures (˃ 10 % OM in 44% of samples, mainly as a result of low decomposition rate. Liming of acid grassland soils did not always reflect in a higher herbage yield. The cause for this inefficiency is plant composition of grassland. Thus, many grassland plants with relatively high production potential have adapted to acid soil conditions. To illustrate the inconsistent liming effect three researches are reviewed. In the first two researches liming along with fertilizer application did not increase the yield comparing to the fertilized control while in the third research the increase amounted 26 %. Liming improves considerably botanical composition of the acid grassland (e.g. sward where Common Bent – Agrostis tenuis Sibth. – prevails and thus indirectly affects palatability and nutritive value of herbage. Grassland liming has a weak

Influence of the sintering temperature in the microstructure of foam glass obtained from waste glass; Influencia da temperatura de queima na microestrutura de espumas vitreas obtidas a partir de residuos de vidro

Energy Technology Data Exchange (ETDEWEB)

Pokorny, A.; Vicenzi, J.; Bergmann, C.P., E-mail: andrea_pokorny@yahoo.com.br [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil)

2012-07-01

In this work, foam glasses were produced from grounded soda-lime glass and a synthetic carbonate, used as a foaming agent, with a similar composition to a dolomite lime, added with different oxides (SiO{sub 2}, Al{sub 2}O{sub 3}, Fe{sub 2}O{sub 3}, MnO{sub 2}, Na{sub 2}O, K{sub 2}O, TiO{sub 2} and P{sub 2}O{sub 5}). The objective was to evaluate the influence of sintering temperature on the properties and microstructure of the obtained material. In addition, the effect of addition of the oxides in the expansion of the ceramic bodies was evaluated. The ceramic bodies were formulated with 3 weight percent of synthetic carbonate, uniaxially pressed and fired within the temperature range from 700 deg C to 950 deg C, with a heating rate of 150K/h. The technological characterization of the ceramic bodies involved the determination of the volumetric expansion and their microstructures have been characterized by optical microscopy and scanning electron microscopy. The experimental results have shown foam glass can be obtained from grounded soda-lime glass, using synthetic carbonate, with the introduction of the different oxides, as foaming agent. (author)

The effect of lime pre-treatments of date palm leaves on delignification and in vitro rumen degradability

NARCIS (Netherlands)

Ghorbani, M.; Ahmadi, F.; Rajaee Rad, A.; Zamiri, M.J.; Cone, J.W.; Polikarpov, I.

2017-01-01

Experiments were conducted to determine the effect of lime pre-treatment on the chemical composition and in vitro rumen degradability of date palm leaves (DPL). Lime pre-treatments, with or without oxygen supply, were applied for 1, 2 and 3 weeks at 25 and 40 °C. Lime was neutralized by the

Archaeomagnetic studies in central Mexico—dating of Mesoamerican lime-plasters

Science.gov (United States)

Hueda-Tanabe, Y.; Soler-Arechalde, A. M.; Urrutia-Fucugauchi, J.; Barba, L.; Manzanilla, L.; Rebolledo-Vieyra, M.; Goguitchaichvili, A.

2004-11-01

For the first time results of an archaeomagnetic study of unburned lime-plasters from Teotihuacan and Tenochtitlan in central Mesoamerica are presented. Plasters made of lime, lithic clasts and water, appear during the Formative Period and were used for a variety of purposes in floors, sculptures, ceramics and supporting media for mural paintings in the Oaxaca and Maya area. In Central Mexico, grinded volcanic scoria rich in iron minerals is incorporated into the lime-plasters mixture. Samples were selected from two archaeological excavation projects in the Teopancazco residential compound of Teotihuacan and the large multi-stage structure of Templo Mayor in Tenochtitlan, where chronological information is available. The intensity of remanent magnetization (natural remanent magnetization (NRM)) and low-field susceptibility are weak reflecting low relative content of magnetic minerals. NRM directions are well grouped and alternating field demagnetization shows single or two-component magnetizations. Rockmagnetic experiments point to fine-grained titanomagnetites with pseudo-single domain behavior. Anisotropy of magnetic susceptibility (AMS) measurements document a depositional fabric, with normal to free-surface minimum AMS axes. Characteristic mean site directions were correlated to the paleosecular variation curve for Mesoamerica. Data from Templo Mayor reflect recent tilting of the structures. Teopancazco mean site declinations show good correspondence with the reference curve, in agreement with the radiocarbon dating. Dates for four stages of Teotihuacan occupancy based on the study of lime-plasters range from AD 350 to 550. A date for a possible Mazapa occupation around AD 850 or 950 is also suggested based on the archaeomagnetic correlation. The archaeomagnetic record of a plaster floor in Teopancazco differed from the other nearby sites pointing to a thermoremanent magnetization; comparison with the reference curve suggests dates around AD 1375 or 1415. The

Study of sticky rice-lime mortar technology for the restoration of historical masonry construction.

Science.gov (United States)

Yang, Fuwei; Zhang, Bingjian; Ma, Qinglin

2010-06-15

Replacing or repairing masonry mortar is usually necessary in the restoration of historical constructions, but the selection of a proper mortar is often problematic. An inappropriate choice can lead to failure of the restoration work, and perhaps even further damage. Thus, a thorough understanding of the original mortar technology and the fabrication of appropriate replacement materials are important research goals. Many kinds of materials have been used over the years in masonry mortars, and the technology has gradually evolved from the single-component mortar of ancient times to hybrid versions containing several ingredients. Beginning in 2450 BCE, lime was used as masonry mortar in Europe. In the Roman era, ground volcanic ash, brick powder, and ceramic chip were added to lime mortar, greatly improving performance. Because of its superior properties, the use of this hydraulic (that is, capable of setting underwater) mortar spread, and it was adopted throughout Europe and western Asia. Perhaps because of the absence of natural materials such as volcanic ash, hydraulic mortar technology was not developed in ancient China. However, a special inorganic-organic composite building material, sticky rice-lime mortar, was developed. This technology was extensively used in important buildings, such as tombs, in urban constructions, and even in water conservancy facilities. It may be the first widespread inorganic-organic composite mortar technology in China, or even in the world. In this Account, we discuss the origins, analysis, performance, and utility in historic preservation of sticky rice-lime mortar. Mortar samples from ancient constructions were analyzed by both chemical methods (including the iodine starch test and the acid attack experiment) and instrumental methods (including thermogravimetric differential scanning calorimetry, X-ray diffraction, Fourier transform infrared, and scanning electron microscopy). These analytical results show that the ancient masonry

Photon emission induced by brittle fracture of borosilicate glasses

Energy Technology Data Exchange (ETDEWEB)

Shiota, Tadashi, E-mail: tshiota@ceram.titech.ac.jp [Department of Metallurgy and Ceramic Science, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo 152-8550 (Japan); Sato, Yoshitaka [Department of Metallurgy and Ceramic Science, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo 152-8550 (Japan); Kishi, Tetsuo [Department of Chemistry and Materials Science, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo 152-8550 (Japan); Yasuda, Kouichi [Department of Metallurgy and Ceramic Science, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo 152-8550 (Japan)

2016-05-15

Photon emission (PE) at wavelength ranges of 430–490 nm (B-PE), 500–600 nm (G-PE) and 610–680 nm (R-PE) caused by brittle fracture was simultaneously measured in the nanosecond-to-microsecond and millisecond time domains for two types of borosilicate glasses: Pyrex-type Tempax glass and BK7 glass. The results were compared to those for silica and soda lime glasses. The time dependence of the PE of Tempax glass was similar to that of silica glass, while the PE intensity was lower. Because Tempax glass contains both silica-rich and borate-rich amorphous phases, the PE must be mainly produced by the fracture of the silica-rich phase. Moreover, the proportion of B-PE of Tempax glass was higher than that of silica glass. This suggests that the measured B-PE might also include very weak PE caused by the fracture of the borate-rich phase. The PE time dependence of BK7 glass was similar to that of soda lime glass, which was different from the case for Tempax glass. The PE intensity of BK7 glass was slightly higher than that of soda lime glass, but much lower than that of Tempax glass. The result indicates that non-bridging oxygen in the glasses affects crack propagation behavior and reduces the PE. - Highlights: • Photon emission (PE) upon brittle fracture of borosilicate glasses was measured. • Pyrex-type Tempax and BK7 glasses showed different PE characteristics. • The rupture of Si–O bonds produces much stronger PE than that of B–O bonds. • Non-bridging oxygen in glass affects crack propagation behavior and reduces the PE.

Effect of liming on the molybdenum content in the root and leaf of ...

African Journals Online (AJOL)

Three liming treatments were employed (1, 3 and 4 t/ha CaCO3). The liming operation used on pseudogley induced a statistically significant increase in molybdenum ion absorption into the root system of tomato. Independently from the aforementioned, the values for the root and leaf molybdenum content of tomato in each ...

LANDSCAPE ARCHAEOLOGY ALONG LIMES TRANSALUTANUS

Directory of Open Access Journals (Sweden)

Eugen S. Teodor

2014-09-01

Full Text Available The project addresses the historical monuments comprised in the longest Roman ‘linear defence’ structure present on the Romanian territory.Despite it being the longest, this historic structure is the least protected and the least known in its technical details. Was indeed Limes Transalutanus an incomplete limes (lacking civilian settlements, for example, an odd construction (a vallum without fossa, an early-alarm line rather than a proper defensive line? Taking on these historical and archaeological challenges, the team attempts to develop an investigation technology applicable to large scale archaeological landscapes - a full evaluation chain, involving aerial survey, surface survey, geophysical investigation, multispectral images analysis, statistic evaluation and archaeological diggings. This technological chain will be systematically applied on the whole length of the objective, that is, on a 155 km distance. The attempt to find answers to issues related to the earth works’ functionality, layout, structure, chronology and relation with adjacent sites will be grounded on exploring the relations of the monument with the surrounding environment, by focussing on finding methods to reconstruct the features of the ancient landscapes, like systematic drilling, palynological tests and toponymical studies.

Separation of hemicellulose-derived saccharides from wood hydrolysate by lime and ion exchange resin.

Science.gov (United States)

Wang, Xiaojun; Zhuang, Jingshun; Fu, Yingjuan; Tian, Guoyu; Wang, Zhaojiang; Qin, Menghua

2016-04-01

A combined process of lime treatment and mixed bed ion exchange was proposed to separate hemicellulose-derived saccharides (HDS) from prehydrolysis liquor (PHL) of lignocellulose as value added products. The optimization of lime treatment achieved up to 44.2% removal of non-saccharide organic compounds (NSOC), mainly colloidal substances, with negligible HDS degradation at 0.5% lime level and subsequent neutralization by phosphoric acid. The residual NSOC and calcium ions in lime-treated PHL were eliminated by mixed bed ion exchange. The breakthrough curves of HDS and NSOC showed selective retention toward NSOC, leading to 75% HDS recovery with 95% purity at 17 bed volumes of exchange capacity. In addition, macroporous resin showed higher exchange capacity than gel resin as indicated by the triple processing volume. The remarkable selectivity of the combined process suggested the feasibility for HDS separation from PHL. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermophysical properties of hydrophobised lime plasters - The influence of ageing

Science.gov (United States)

Pavlíková, Milena; Zemanová, Lucie; Pavlík, Zbyšek

2017-07-01

The building envelope is a principal responsible for buildings energy loses. Lime plasters as the most popular finishing materials of historical buildings and culture monuments influence the thermal behaviour as well as construction material of masonry. On this account, the effect of ageing on the thermophysical properties of a newly designed lime plasters containing hydrophobic admixture is analysed in the paper. For the comparative purposes, the reference lime plaster is tested. The ageing is accelerated with controlled carbonation process to simulate the final plasters properties. Basic characterization of the tested materials is done using bulk density, matrix density, and porosity measurements. Thermal conductivity and volumetric heat capacity are experimentally assessed using a transient impulse method. The obtained data revealed the significant changes of the both studied thermal parameters in the dependence on plasters composition and age. The assessed material parameters will be stored in a material database, where will find use as an input data for computational modelling of heat transport in this type of porous building materials and evaluation of energy-savings and sustainability issues.

Baking soda and salt in bakeries of Mehrdasht (Najafabad), Isfahan, Iran: a survey on a typical rural population in a developing country.

Science.gov (United States)

Rezaiimofrad, M; Rangraz Jeddi, F; Azarbad, Z

2013-03-01

Bread is a valuable source of proteins, minerals and calories. Baking soda prevents the absorption and digestion of bread and more salt used in production of bread also causes different diseases. This study was conducted to determine the amount of soda and salt in bakeries. Cross-sectional descriptive study was carried out on 50 bakeries district during 2009. 400 samples were collected in four steps randomly. The standard PH baking soda in bread and salt less than 2 g/100 g was considered as the reference. The PH less than 6.2 was seen in 91.5% of samples and analyzed by random effect analysis. In 64.5% of samples, the amount of salt was more than the standard. The amount of baking soda used in the bakeries was not high; bakers either had no enough knowledge about the amount of salt or had more other reasons. Drastic measures are recommended.

THE LIME PURIFICATION OF SUGAR –CONTAINING SOLUTION USING HIGH VISCOSITY COLLOIDAL SOLUTIONS

Directory of Open Access Journals (Sweden)

K. V.

2015-12-01

Full Text Available Aim of the work was to determine the efficiency of combined application of lime and high-viscous suspensions, containing the aluminium nanoparticles as a precursor in treatment of sugar-containing solutions. At the first stage the aluminium nanopowder, encapsulated into a salt matrix, was produced by the combined precipitation from a gas phase of metal and halogenide of alkali metal (NaCl. For the long-term stabilization of aluminum nanoparticles the method, developed by the authors, for dispersing these powders in the composition of polyethylene glycols was used, providing the colloidal solution of high viscosity (gel. At the second stage, as an object of investigation a juice of sugar beet, produced in the laboratory conditions by water extracting from the beet chips, was applied. In the produced juice the main characteristics of its quality were determined: the content of solids, sucrose, its purity was calculated (ratio of sucrose to solids content, in%. The content of protein and pectin components was also determined (as the main components of the colloidal fraction of the diffusion juice. Conventionally, as a basic reagent for the process of a lime pretreatment a lime milk of 1.18 g/cm3 density, prepared by liming the burned lime using hot water, was used. During the experiments the effectiveness of reagents, containing aluminum in nanoform, on the degree of removal of the colloidal dispersion substances in the process of juice purification in sugar beet production and improvement of its quality, is shown. However, the obtained results show that, depending on the method of producing, the additional reagents with aluminium nanoparticles have different effect on change of diffusion juice purity in the process of its treatment by the lime milk.

Liming Influences Growth and Nutrient Balances in Sugar Maple (Acer saccharum) Seedlings on an Acidic Forest Soil

Science.gov (United States)

Dudley J. Raynal

1998-01-01

Forests in the northeastern US have been limed to mitigate soil acidification and the acidity of surface waters and to improve soil base cation status. Much of the area considered for liming is within the range of sugar maple (Acer saccharum), but there is a poor understanding of how liming influences growth and nutrient balance of this species on...

40 CFR 141.564 - My system practices lime softening-is there any special provision regarding my individual filter...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false My system practices lime softening-is... People Individual Filter Turbidity Requirements § 141.564 My system practices lime softening—is there any special provision regarding my individual filter turbidity monitoring? If your system utilizes lime...

Liming and fertilisation in Pinus taeda plantations with severe nutrient deficiency in savanna soils

Directory of Open Access Journals (Sweden)

Araína Hulmann Batista

2014-11-01

Full Text Available Soils with high acidity and low exchangeable bases may be responsible for low yields of Pinus taeda in a forest plantation at Jaguariaíva, Paraná State, Brazil. The aim of this study was to evaluate the effect of liming and fertilisation, applied over litter, on two selected areas with Pinus taeda plantations. Soil, litter and pine needles were evaluated for K, Ca and Mg concentrations and soil acidity parameters. Seven treatments were applied: (i complete (N, P, K, Zn, Cu, B, Mo, and lime; (ii without N, P, and K; (iii without Zn, Cu, B, and Mo; (iv without K; (v without Zn; (vi without lime; and (vii control (without nutrients and lime. Soil samples were collected at five soil depths (0-5, 5-10, 10-20, 20-40 and 40-60 cm simultaneously with litter samples. Needles were also collected from the first and second pine flushes. Liming induced soil pH, Ca2+, and Mg2+ increases, and the opposite was observed for Al3+ and Al saturation. Fertilisation increased soil exchangeable K+ concentrations and needle and litter K concentrations. The low Ca and Mg concentrations found in the plant needles might be attributable to their low mobility.

Cadmium uptake by tobacco as affected by liming, N form, and year of cultivation

International Nuclear Information System (INIS)

Tsadilas, C.D.; Karaivazoglou, N.A.; Tsotsolis, N.C.; Stamatiadis, S.; Samaras, V.

2005-01-01

Tobacco is able to accumulate cadmium and reduction of cadmium content can reduce health hazards to smokers. Soil pH and form of N fertilizers are among the factors affecting Cd uptake by tobacco. This hypothesis was tested in an acid soil in northern Greece by a four year field experiment. The variability of Cd uptake by tobacco was attributed to the variation of soil Cd availability as affected by soil pH. Liming with 3000 kg Ca(OH) 2 ha -1 increased soil pH by 0.8 units and decreased extractable with DTPA soil and leaf Cd by 40% and 35%, respectively. The ammonium fertilizer caused the opposite, but weaker, effects. Liming reduced soil Cd more in the ammonium treatment than in nitrate or combined N treatments. The year of cultivation strongly affected soil and leaf Cd. Four years after tobacco cultivation, soil pH was reduced by 0.5 units, whereas soil and leaf Cd reduction was more than 60% in the limed treatments. Liming affected Cd uptake only in the first three years of cultivation. - Liming and N form affect Cd uptake by Virginia tobacco which contributes significantly to the great reduction of extractable soil Cd after three years of continuous cultivation

Lime and rates and sources of phosphorus as influencing soybean yield and chemical properties of Pelotas soil (alfisol)

International Nuclear Information System (INIS)

Machado, M.O.

1983-01-01

The effect of five phosphates as sources of phosphorus for soybean (Bragg cultivar) was evaluated in two rates (100 and 200 Kg/ha of total P 2 O 5 ), on limed and unlimed soil condtions. The experiment was carried out under field conditions, during the soybean growing season of 1973/74, 1974/75, 1975/76 and 1976/77, at UEPAE Pelotas station. The pH and the exchangeable Ca + Mg content from the soil were increased with Gafsa phosphate, but mainly with lime, Thomas slag and Yoorin thermophosphate application. The exchangeable Al content was eliminated by lime application and decreased annually by application of Gafsa phosphate, Thomas slag and Yoorin thermophosphate, when the lime was not applied. Thomas slag and Yoorin thermophosphate were the best phosphates for grain yield and do without lime: however, under limed soil conditions all phosphates had some efficiency, except for the Gafsa phosphate in the first growing season. (Author) [pt

Novel MEMS Apparatus for In Situ Thermo-Mechanical Tensile Testing of Materials at the Micro- and Nano-Scale (Preprint)

Science.gov (United States)

2009-04-01

outer ends of the MEMS-stage connect the stage to a macroscopic piezo -electric actuated test frame using rigid pins. In order to apply uniaxial...carbide also served as the resistor for Joule heating. This heater was used to melt glass (Soda lime glass, softening temperature: 720C, Gold Seal

40 CFR 141.553 - My system practices lime softening-is there any special provision regarding my combined filter...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false My system practices lime softening-is... Filter Effluent Requirements § 141.553 My system practices lime softening—is there any special provision regarding my combined filter effluent? If your system practices lime softening, you may acidify...

Evaluation of Cement, Lime, and Asphalt Amended Municipal Solid Waste Incinerator Residues

Science.gov (United States)

1989-09-01

the lime column over time ( Atlas & Bartha , 1987). Certainly, a more extensive evaluation of the lime amended residue’s microbial activity is required...4.02 ASTM D 1559 (1988) Annual Book of ASTM Standards: Road & Paving Materials; Traveled Surface Characteristics, Sec 4, Vol 4.03 Atlas , R. & R. Bartha ...1987) Microbial Ecology : Fundamentals & Applications, Benjamin-Cummings, Menlo, CA Barrow N., J. Bowden, A. Posner, & J. Quirk (1981) Describing the

Substrate pH and butterfly bush response to dolomitic lime or steel slag amendment

Science.gov (United States)

Steel slag is a fertilizer amendment with a high concentration of calcium oxide, and thus capable of raising substrate pH similar to dolomitic lime. Steel slag, however, contains higher concentrations of some nutrients, such as iron, manganese, and silicon, compared to dolomitic lime. The objectiv...

A theory manual for multi-physics code coupling in LIME.

Energy Technology Data Exchange (ETDEWEB)

Belcourt, Noel; Bartlett, Roscoe Ainsworth; Pawlowski, Roger Patrick; Schmidt, Rodney Cannon; Hooper, Russell Warren

2011-03-01

The Lightweight Integrating Multi-physics Environment (LIME) is a software package for creating multi-physics simulation codes. Its primary application space is when computer codes are currently available to solve different parts of a multi-physics problem and now need to be coupled with other such codes. In this report we define a common domain language for discussing multi-physics coupling and describe the basic theory associated with multiphysics coupling algorithms that are to be supported in LIME. We provide an assessment of coupling techniques for both steady-state and time dependent coupled systems. Example couplings are also demonstrated.

Initial growth of Schizolobium parahybae in Brazilian Cerrado soil under liming and mineral fertilization

Directory of Open Access Journals (Sweden)

Ademilson Coneglian

Full Text Available ABSTRACT High prices and the scarcity of hardwoods require the use of alternative wood sources, such as the Guapuruvu (Schizolobium parahybae, an arboreal species native to the Atlantic Forest, which has fast growth and high market potential. However, there is no information on its cultivation in the Brazilian Cerrado. Thus, this study aimed to analyze the contribution of mineral fertilization and liming in a Cerrado soil on the initial growth of Schizolobium parahybae. The experiment was set in a randomized block design, with 4 treatments (Cerrado soil; soil + liming; soil + fertilizer; and soil + fertilizer + liming and 15 replicates. The following variables were analyzed: plant height, stem diameter, number of leaves, total, shoot, leaf, root and stem dry matter, and root/shoot ratio. The obtained data were subjected to the analysis of variance, Tukey test and regression analysis. During the initial growth, Schizolobium parahybae can be cultivated in a Brazilian Cerrado soil only under mineral fertilization, with no need for soil liming.

Homespun remedy, homespun toxicity: baking soda ingestion for dyspepsia.

Science.gov (United States)

Ajbani, Keyur; Chansky, Michael E; Baumann, Brigitte M

2011-04-01

A 68-year-old man presented to the Emergency Department with a severe metabolic alkalosis after ingesting large quantities of baking soda to treat his dyspepsia. His underlying pulmonary disease and a progressively worsening mental status necessitated intubation for respiratory failure. Laboratory studies revealed a hyponatremic, hypochloremic, hypokalemic metabolic alkalosis. The patient was successfully treated after cessation of the oral bicarbonate, initiation of intravenous hydration, and correction of electrolyte abnormalities. Copyright © 2011 Elsevier Inc. All rights reserved.

Vanadium extraction from slimes by the lime-bicarbonate method

International Nuclear Information System (INIS)

Lishchenko, T.V.; Vdovina, L.V.; Slobodchikova, R.I.

1978-01-01

Some main parameters of the lime-bicarbonate method of extracting vanadium from residues obtained in washing waters of mazut boilers on thermal stations have been determined. To study the process of vanadium extraction during caking of the residues with lime and subsequent leaching of water-soluble vanadium, a ''Minsk-22'' computer has been used for computation. Analysis of the equation derived has shown that a change in temperature of vanadium leaching, density of pulp, and a kind of heating of the charge affect the process only slightly. It has also been shown that the calcination temperature is expedient to be kept above 850 deg C and consumption temperature is expedient to be kept above 85O deg C and consumption of lime must not exceed 20% of the residues weight. Bicarbonate consumption exerts a decisive influence on completeness of vanadium extraction and must be increased up to >35%; duration of leaching should be raised up to 30-45 minutes. With increasing calcination temperature the duration of leaching decreases. When temperature and duration of calcination increase, the formation of water-soluble vanadium intensifies. With the aid of optimization program seven variants have been chosen, which ensure vanadium extraction into solution by 95-100%

Sorghum yield after liming and combinations of phosphorus sources

Directory of Open Access Journals (Sweden)

Thiago C. Silveira

Full Text Available ABSTRACT Phosphate fertilization has increased sorghum yield, but few studies are available on sorghum production and efficient fertilizer management related to liming and phosphorus (P sources. This work evaluates production, dry matter partitioning and agronomic efficiency (AEI in successive sorghum cycles after application of limestone and combinations of phosphorus sources. Two cycles were conducted in sequence in the same experimental field, in a 2 x 6 factorial scheme, corresponding to soil with or without liming and six combinations of P2O5 sources: control (0 kg ha-1 P2O5, 100% Itafós natural phosphate (NP, 75% NP + 25% single superphosphate (SS, 50% NP + 50% SS, 25% NP + 75% SS and 100% SS. Pots with capacity for 8 dm3 were used in a randomized block design with four replicates. The first cycle, conducted in the summer/autumn season, reached the highest dry matter production and P accumulation in treatments with higher SS proportions, leading to higher AEI. Subsequently, in the second cycle, conducted considering only the residual phosphate fertilization of the first cycle, highest dry matter production and AEI were obtained in the treatment with 100% or higher proportions of natural phosphate in the presence of liming, most likely due to the gradual release of P.

The influence of lime and nitrogen fertilisers on spore counts of Pithomyces chartarum in pasture.

Science.gov (United States)

Cuttance, E L; Laven, R A; Mason, W A; Stevenson, M

2016-11-01

To determine whether the application of lime or nitrogen to pasture affected the spore counts of Pithomyces chartarum. The lime application studies were undertaken on a spring-calving, pasture-based, commercial dairy farm near Te Awamutu, New Zealand. On 6 November 2012, five randomly selected paddocks were split into three equal sections. In two of the sections, lime was applied at either 1.5 or 2.5 t/ha, and the central section was left as an untreated control. Each section was sampled for spore counting weekly from 16 January to 15 May 2013. Starting in January 2013, five other randomly selected paddocks were monitored for spore counts. On 20 March 2013 the average spore counts in three paddocks were >100,000 spores/g of pasture. These paddocks were then divided into three equal sections and lime was applied as described above. Spore counting in each section continued weekly until 15 May 2013. The nitrogen application study was carried out on three commercial dairy farms near Te Awamutu, New Zealand. Two randomly selected paddocks on each farm were divided into three equal sections and, on 20 December 2012, nitrogen in the form of urea was applied at either 50 or 80 kg urea/ha to two of the sections; the central section remained as an untreated control. Each section was sampled for spore counting weekly from 16 January to 15 May 2013. Following pre-summer lime application, treatment at 1.5 or 2.5 t/ha did not affect spore counts over time compared with the control section (p>0.26). Similarly following autumn lime application, treatment at 1.5 or 2.5 t/ha did not affect spore counts over time compared with the control section (p>0.11). Following nitrogen application median spore counts remained 0.49). This study found that application of lime before the risk period for facial eczema, in November, application of lime after a spore count rise, in March, or urea application in December did not affect changes in number of spores produced by P. chartarum. This

The Fracture Process of Tempered Soda-Lime-Silica Glass

DEFF Research Database (Denmark)

Nielsen, Jens Henrik; Olesen, John Forbes; Stang, Henrik

2009-01-01

This work presents experimental observations of the characteristic fracture process of tempered glass. Square specimens with a side length of 300 mm, various thicknesses and a residual stress state characterized by photoelastic measurements were used. Fracture was initiated using a 2.5 mm diamond...

Shock wave propagation in soda lime glass using optical ...

Indian Academy of Sciences (India)

2016-06-16

Jun 16, 2016 ... probe beam in the transverse direction coupled with an optical streak .... (650 ps) was split using a beam splitter after the fifth amplifier stage in the ..... [17] A S Joshi et al, Fusion Engg. Design 44, 067 (1999). [18] A K Sharma ...

Application of lime (CaCO3) to promote forest recovery from severe acidification increases potential for earthworm invasion

Science.gov (United States)

Homan, Caitlin; Beirer, Colin M; McCay, Timothy S; Lawrence, Gregory B.

2016-01-01

The application of lime (calcium carbonate) may be a cost-effective strategy to promote forest ecosystem recovery from acid impairment, under contemporary low levels of acidic deposition. However, liming acidified soils may create more suitable habitat for invasive earthworms that cause significant damage to forest floor communities and may disrupt ecosystem processes. We investigated the potential effects of liming in acidified soils where earthworms are rare in conjunction with a whole-ecosystem liming experiment in the chronically acidified forests of the western Adirondacks (USA). Using a microcosm experiment that replicated the whole-ecosystem treatment, we evaluated effects of soil liming on Lumbricus terrestris survivorship and biomass growth. We found that a moderate lime application (raising pH from 3.1 to 3.7) dramatically increased survival and biomass of L. terrestris, likely via increases in soil pH and associated reductions in inorganic aluminum, a known toxin. Very few L. terrestris individuals survived in unlimed soils, whereas earthworms in limed soils survived, grew, and rapidly consumed leaf litter. We supplemented this experiment with field surveys of extant earthworm communities along a gradient of soil pH in Adirondack hardwood forests, ranging from severely acidified (pH 5). In the field, no earthworms were observed where soil pH 4.4 and human dispersal vectors, including proximity to roads and public fishing access, were most prevalent. Overall our results suggest that moderate lime additions can be sufficient to increase earthworm invasion risk where dispersal vectors are present.

Baking soda pica: a case of hypokalemic metabolic alkalosis and rhabdomyolysis in pregnancy.

Science.gov (United States)

Grotegut, Chad A; Dandolu, Vani; Katari, Sunita; Whiteman, Valerie E; Geifman-Holtzman, Ossie; Teitelman, Melissa

2006-02-01

We report a case of baking soda pica in a woman at 31 weeks of pregnancy causing severe hypokalemic metabolic alkalosis and rhabdomyolysis. A multigravida at 31 weeks of gestation presented with weakness and muscle pain. She was found to have severe hypokalemic metabolic alkalosis and rhabdomyolysis, with elevation in serum transaminases and hypertension. We initially thought the patient had an atypical presentation of preeclampsia until it was realized that she was ingesting 1 full box of baking soda (454 g sodium bicarbonate) per day. Symptoms and abnormal laboratory findings resolved with discontinuation of the patient's pica practices. Pica is a common but often overlooked practice that can potentially lead to life-threatening disorders. A thorough evaluation of a patient's dietary intake is extremely important, especially in the setting of atypical presentations of disease in pregnancy.

Specification and time required for the application of a lime-based render inside historic buildings

Directory of Open Access Journals (Sweden)

Vasco Peixoto de Freitas

2008-01-01

Full Text Available Intervention in ancient buildings with historical and architectural value requires traditional techniques, such as the use of lime mortars for internal and external wall renderings. In order to ensure the desired performance, these rendering mortars must be rigorously specified and quality controls have to be performed during application. The choice of mortar composition should take account of factors such as compatibility with the substrate, mechanical requirements and water behaviour. The construction schedule, which used to be considered a second order variable, nowadays plays a decisive role in the selection of the rendering technique, given its effects upon costs. How should lime-based mortars be specified? How much time is required for the application and curing of a lime-based render? This paper reflects upon the feasibility of using traditional lime mortars in three-layer renders inside churches and monasteries under adverse hygrothermal conditions and when time is critical. A case study is presented in which internal lime mortar renderings were applied in a church in Northern Portugal, where the very high relative humidity meant that several months were necessary before the drying process was complete.

The effect of baking soda/hydrogen peroxide dentifrice (Mentadent) and a 0.12 percent chlorhexidine gluconate mouthrinse (Peridex) in reducing gingival bleeding.

Science.gov (United States)

Taller, S H

1993-01-01

The purpose of this study was to determine the effectiveness of a baking soda/hydrogen peroxide dentifrice, Mentadent, and a 0.12 percent chlorhexidine gluconate mouthrinse, Peridex, in reducing gingival bleeding. Forty subjects were divided into three groups; the baking soda group, the chlorhexidine group and the control group. All groups received oral hygiene instruction and brushed and flossed three times per day. Bleeding point scores were evaluated at baseline and at five weeks. The baking soda/hydrogen peroxide group used the supplied dentifrice as their sole toothpaste. The 0.12 percent chlorhexidine group used the mouthrinse twice per day. The control group performed oral hygiene as instructed. At five weeks, the 0.12 percent chlorhexidine mouthrinse significantly reduced gingival bleeding. The dentifrice and control groups revealed no statistically significant reductions. The results indicate that the 0.12 percent chlorhexidine mouthrinse is useful in improving oral health, whereas the baking soda/hydrogen peroxide dentifrice offered no advantages to conventional oral hygiene.

Simultaneous removal of colour, phosphorus and disinfection from treated wastewater using an agent synthesized from amorphous silica and hydrated lime.

Science.gov (United States)

Yamashita, Takahiro; Aketo, Tsuyoshi; Minowa, Nobutaka; Sugimoto, Kiyomi; Yokoyama, Hiroshi; Ogino, Akifumi; Tanaka, Yasuo

2013-01-01

An agent synthesized from amorphous silica and hydrated lime (CSH-lime) was investigated for its ability to simultaneously remove the colour, phosphorus and disinfection from the effluents from wastewater treatment plants on swine farms. CSH-lime removed the colour and phosphate from the effluents, with the colour-removal effects especially high at pH 12, and phosphorous removal was more effective in strongly alkaline conditions (pH > 10). Colour decreased from 432 +/-111 (mean +/- SD) to 107 +/- 41 colour units and PO4(3-)P was reduced from 45 +/- 39 mg/L to undetectable levels at the CSH-lime dose of 2.0% w/v. Moreover, CSH-lime reduced the total organic carbon from 99.0 to 37.9 mg/L at the dose of 2.0% w/v and was effective at inactivating total heterotrophic and coliform bacteria. However, CSH-lime did not remove nitrogen compounds such as nitrite, nitrate and ammonium. Colour was also removed from dye solutions by CSH-lime, at the same dose.

Hemp-Lime Performance in Danish Climatic Context. Thermal Conductivity as a Function of Moisture Content

DEFF Research Database (Denmark)

Antonov, Yovko Ivanov; Jensen, Rasmus Lund; Pomianowski, Michal Zbigniew

2016-01-01

concrete is a bio-based building material composed of the woody core of industrial hemp and lime based binder. It is a non-load-bearing material, which can be used as floor and around structural frames for walls and roof. The material is characterized by relatively low environmental impact, moderate...... thermal properties and, high air and moisture permeability. The properties vary with binder composition, mixing and casting techniques, as well as intended application. This research presents preliminary heat and moisture building simulations of single family house made out of hemp-lime composite....... To evaluate the performance of hemp-lime, it is compared to models with common external walls, upon defined parameters. The article also determines the variation of thermal conductivity for hemp-lime commercial plaster and wall mix, as a function of moisture content. The most promising binder composition...

Contrasting the Genetic Patterns of Microbial Communities in Soda Lakes with and without Cyanobacterial Bloom.

Science.gov (United States)

Andreote, Ana P D; Dini-Andreote, Francisco; Rigonato, Janaina; Machineski, Gabriela Silva; Souza, Bruno C E; Barbiero, Laurent; Rezende-Filho, Ary T; Fiore, Marli F

2018-01-01

Soda lakes have high levels of sodium carbonates and are characterized by salinity and elevated pH. These ecosystems are found across Africa, Europe, Asia, Australia, North, Central, and South America. Particularly in Brazil, the Pantanal region has a series of hundreds of shallow soda lakes (ca. 600) potentially colonized by a diverse haloalkaliphilic microbial community. Biological information of these systems is still elusive, in particular data on the description of the main taxa involved in the biogeochemical cycling of life-important elements. Here, we used metagenomic sequencing to contrast the composition and functional patterns of the microbial communities of two distinct soda lakes from the sub-region Nhecolândia, state of Mato Grosso do Sul, Brazil. These two lakes differ by permanent cyanobacterial blooms (Salina Verde, green-water lake) and by no record of cyanobacterial blooms (Salina Preta, black-water lake). The dominant bacterial species in the Salina Verde bloom was Anabaenopsis elenkinii . This cyanobacterium altered local abiotic parameters such as pH, turbidity, and dissolved oxygen and consequently the overall structure of the microbial community. In Salina Preta, the microbial community had a more structured taxonomic profile. Therefore, the distribution of metabolic functions in Salina Preta community encompassed a large number of taxa, whereas, in Salina Verde, the functional potential was restrained across a specific set of taxa. Distinct signatures in the abundance of genes associated with the cycling of carbon, nitrogen, and sulfur were found. Interestingly, genes linked to arsenic resistance metabolism were present at higher abundance in Salina Verde and they were associated with the cyanobacterial bloom. Collectively, this study advances fundamental knowledge on the composition and genetic potential of microbial communities inhabiting tropical soda lakes.

Contrasting the Genetic Patterns of Microbial Communities in Soda Lakes with and without Cyanobacterial Bloom

Science.gov (United States)

Andreote, Ana P. D.; Dini-Andreote, Francisco; Rigonato, Janaina; Machineski, Gabriela Silva; Souza, Bruno C. E.; Barbiero, Laurent; Rezende-Filho, Ary T.; Fiore, Marli F.

2018-01-01

Soda lakes have high levels of sodium carbonates and are characterized by salinity and elevated pH. These ecosystems are found across Africa, Europe, Asia, Australia, North, Central, and South America. Particularly in Brazil, the Pantanal region has a series of hundreds of shallow soda lakes (ca. 600) potentially colonized by a diverse haloalkaliphilic microbial community. Biological information of these systems is still elusive, in particular data on the description of the main taxa involved in the biogeochemical cycling of life-important elements. Here, we used metagenomic sequencing to contrast the composition and functional patterns of the microbial communities of two distinct soda lakes from the sub-region Nhecolândia, state of Mato Grosso do Sul, Brazil. These two lakes differ by permanent cyanobacterial blooms (Salina Verde, green-water lake) and by no record of cyanobacterial blooms (Salina Preta, black-water lake). The dominant bacterial species in the Salina Verde bloom was Anabaenopsis elenkinii. This cyanobacterium altered local abiotic parameters such as pH, turbidity, and dissolved oxygen and consequently the overall structure of the microbial community. In Salina Preta, the microbial community had a more structured taxonomic profile. Therefore, the distribution of metabolic functions in Salina Preta community encompassed a large number of taxa, whereas, in Salina Verde, the functional potential was restrained across a specific set of taxa. Distinct signatures in the abundance of genes associated with the cycling of carbon, nitrogen, and sulfur were found. Interestingly, genes linked to arsenic resistance metabolism were present at higher abundance in Salina Verde and they were associated with the cyanobacterial bloom. Collectively, this study advances fundamental knowledge on the composition and genetic potential of microbial communities inhabiting tropical soda lakes. PMID:29520256

Contrasting the Genetic Patterns of Microbial Communities in Soda Lakes with and without Cyanobacterial Bloom

Directory of Open Access Journals (Sweden)

Ana P. D. Andreote

2018-02-01

Full Text Available Soda lakes have high levels of sodium carbonates and are characterized by salinity and elevated pH. These ecosystems are found across Africa, Europe, Asia, Australia, North, Central, and South America. Particularly in Brazil, the Pantanal region has a series of hundreds of shallow soda lakes (ca. 600 potentially colonized by a diverse haloalkaliphilic microbial community. Biological information of these systems is still elusive, in particular data on the description of the main taxa involved in the biogeochemical cycling of life-important elements. Here, we used metagenomic sequencing to contrast the composition and functional patterns of the microbial communities of two distinct soda lakes from the sub-region Nhecolândia, state of Mato Grosso do Sul, Brazil. These two lakes differ by permanent cyanobacterial blooms (Salina Verde, green-water lake and by no record of cyanobacterial blooms (Salina Preta, black-water lake. The dominant bacterial species in the Salina Verde bloom was Anabaenopsis elenkinii. This cyanobacterium altered local abiotic parameters such as pH, turbidity, and dissolved oxygen and consequently the overall structure of the microbial community. In Salina Preta, the microbial community had a more structured taxonomic profile. Therefore, the distribution of metabolic functions in Salina Preta community encompassed a large number of taxa, whereas, in Salina Verde, the functional potential was restrained across a specific set of taxa. Distinct signatures in the abundance of genes associated with the cycling of carbon, nitrogen, and sulfur were found. Interestingly, genes linked to arsenic resistance metabolism were present at higher abundance in Salina Verde and they were associated with the cyanobacterial bloom. Collectively, this study advances fundamental knowledge on the composition and genetic potential of microbial communities inhabiting tropical soda lakes.

Energy Efficient Microwave Hybrid Processing of Lime for Cement, Steel, and Glass Industries

Energy Technology Data Exchange (ETDEWEB)

Fall, Morgana L; Yakovlev, Vadim; Sahi, Catherine; Baranova, Inessa; Bowers, Johnney G; Esquenazi\t, Gibran L

2012-02-10

In this study, the microwave materials interactions were studied through dielectric property measurements, process modeling, and lab scale microwave hybrid calcination tests. Characterization and analysis were performed to evaluate material reactions and energy usage. Processing parameters for laboratory scale and larger scale calcining experiments were developed for MAT limestone calcination. Early stage equipment design concepts were developed, with a focus on microwave post heating treatment. The retrofitting of existing rotary calcine equipment in the lime industry was assessed and found to be feasible. Ceralink sought to address some of the major barriers to the uptake of MAT identified as the need for (1) team approach with end users, technology partners, and equipment manufacturers, (2) modeling that incorporates kiln materials and variations to the design of industrial microwave equipment. This project has furthered the commercialization effort of MAT by working closely with an industrial lime manufacturer to educate them regarding MAT, identifying equipment manufacturer to supply microwave equipment, and developing a sophisticated MAT modeling with WPI, the university partner. MAT was shown to enhance calcining through lower energy consumption and faster reaction rates compared to conventional processing. Laboratory testing concluded that a 23% reduction in energy was possible for calcining small batches (5kg). Scale-up testing indicated that the energy savings increased as a function of load size and 36% energy savings was demonstrated (22 kg). A sophisticated model was developed which combines simultaneous microwave and conventional heating. Continued development of this modeling software could be used for larger scale calcining simulations, which would be a beneficial low-cost tool for exploring equipment design prior to actual building. Based on these findings, estimates for production scale MAT calcining benefits were calculated, assuming uptake of

State policies targeting junk food in schools: racial/ethnic differences in the effect of policy change on soda consumption.

Science.gov (United States)

Taber, Daniel R; Stevens, June; Evenson, Kelly R; Ward, Dianne S; Poole, Charles; Maciejewski, Matthew L; Murray, David M; Brownson, Ross C

2011-09-01

We estimated the association between state policy changes and adolescent soda consumption and body mass index (BMI) percentile, overall and by race/ethnicity. We obtained data on whether states required or recommended that schools prohibit junk food in vending machines, snack bars, concession stands, and parties from the 2000 and 2006 School Health Policies and Programs Study. We used linear mixed models to estimate the association between 2000-2006 policy changes and 2007 soda consumption and BMI percentile, as reported by 90 730 students in 33 states and the District of Columbia in the Youth Risk Behavior Survey, and to test for racial/ethnic differences in the associations. Policy changes targeting concession stands were associated with 0.09 fewer servings of soda per day among students (95% confidence interval [CI] = -0.17, -0.01); the association was more pronounced among non-Hispanic Blacks (0.19 fewer servings per day). Policy changes targeting parties were associated with 0.07 fewer servings per day (95% CI = -0.13, 0.00). Policy changes were not associated with BMI percentile in any group. State policies targeting junk food in schools may reduce racial/ethnic disparities in adolescent soda consumption, but their impact appears to be too weak to reduce adolescent BMI percentile.

Molecular characterization and pathogenicity assays of Colletotrichum acutatum, causal agent for lime anthracnose in Texas

Science.gov (United States)

Several distorted Mexican lime [Citrus aurantiifolia (Christm). Swingle] fruit, leaf, and twig samples with lime anthracnose symptoms were collected from three trees in residential areas of Brownsville, Texas. The causal fungal organism, Colletotrichum acutatum J. H. Simmonds was isolated from leave...

A comparative study of the effect of diet and soda carbonated drinks ...

African Journals Online (AJOL)

EB

2013-09-03

Sep 3, 2013 ... Objectives: A comparative effect of the diet and regular soda carbonated drinks on the histology of the cerebellum of female albino Wistar rats was ... contains caffeine, depending on the quantities consumed5. Caffeine is linked ... consumption might result in seizures, memory loss, dizziness, headache and ...

Effect of high thermal expansion glass infiltration on mechanical ...

Indian Academy of Sciences (India)

This work studies the effect on the mechanical properties of alumina-10 wt% zirconia (3 mol% yttria stabilized) composite by infiltrating glass of a higher thermal expansion (soda lime glass) on the surface at high temperature. The glass improved the strength of composite at room temperature as well as at high temperature.

Effect of soil compaction and biomass removal on soil CO2 efflux in a Missouri forest

Science.gov (United States)

Felix, Jr. Ponder

2005-01-01

Forest disturbances associated with harvesting activities can affect soil properties and soil respiration. A soda-lime technique was used to measure soil carbon dioxide (CO2) efflux rates in clearcut plots of a Missouri oak-hickory (Quercus spp. L.-Carya spp. Nutt.) forest 4 years after being treated with two levels of forest...

A Re-evaluation of the Physiochemistry of Glass on the Basis of Recent Developments and its Relevance to the Glass Industry

NARCIS (Netherlands)

Veer, F.A.; Bristogianni, Telesilla; Justino de Lima, Clarissa; Louter, Christian; Bos, Freek; Belis, Jan; Veer, Fred; Nijsse, Rob

The classical image of glass is that of a rigid, transparent brittle material characterized by a non-crystalline microstructure. This 19th and 20th century image however is mostly based on the contrast between soda lime glass and metals. It does not really make sense in the 21th century where more

Investigations on generation and use of a sludge-lime fertilizer. Untersuchungen zur Erzeugung und Anwendung eines Klaerschlamm-Kalkduengers

Energy Technology Data Exchange (ETDEWEB)

Boehnke, B; Weiling, R

1980-06-01

Sludge is an important energy and raw material source, which if possible should be utilized in agriculture. Through the addition of unslaked lime a hygienically safe product can be prepared with the help of a suitable treatment process and can be offered in granulated form as a valuable sludge-lime fertilizer. Sludges of different consistencies and origins were investigated. Varying amounts and types of lime were used and the products were tested for easy handling, storage capability and temperature influence on the hygienic conditions. In order to obtain a disseminable substance, a solid matter content of over 60% is necessary. This is achieved through variation of the lime content depending on the solid content of the respective sludge. According to the existing regulations, which fix the minimum CaO content in a lime fertilizer at 30%, a predewatering of the sludge up to 25%-30% of the solid matter content is sufficient. Economic viability is assured, specially in areas where intensive agricultural use of lime fertilizer is necessary. (orig.) With 32 refs., 15 tabs., 27 figs.

CCD camera eases the control of a soda recovery boiler; CCD-kamera helpottaa soodakattilan valvontaa

Energy Technology Data Exchange (ETDEWEB)

Kinnunen, L.

2001-07-01

Fortum Technology has developed a CCD firebox camera, based on semiconductor technology, enduring hard conditions of soda recovery boiler longer than traditional cameras. The firebox camera air- cooled and the same air is pressed over the main lens so it remains clean despite of the alkaline liquor splashing around in the boiler. The image of the boiler is transferred through the main lens, image transfer lens and a special filter, mounted inside the camera tube, into the CCD camera. The first CCD camera system has been in use since 1999 in Sunila pulp mill in Kotka, owned by Myllykoski Oy and Enso Oyj. The mill has two medium-sized soda recovery boilers. The amount of black liquor, formed daily, is about 2000 tons DS, which is more than enough for the heat generation. Even electric power generation exceeds sometimes the demand, so the surplus power can be sold out. Black liquor is sprayed inside the soda recovery boiler with high pressure. The liquor form droplets in the boiler, the temperature of which is over 1000 deg C. A full-hot pile is formed at the bottom of the boiler after burning. The size and shape of the pile effect on the efficiency and the emissions of the boiler. The camera has operated well.

Acute toxicity from baking soda ingestion.

Science.gov (United States)

Thomas, S H; Stone, C K

1994-01-01

Sodium bicarbonate is an extremely well-known agent that historically has been used for a variety of medical conditions. Despite the widespread use of oral bicarbonate, little documented toxicity has occurred, and the emergency medicine literature contains no reports of toxicity caused by the ingestion of baking soda. Risks of acute and chronic oral bicarbonate ingestion include metabolic alkalosis, hypernatremia, hypertension, gastric rupture, hyporeninemia, hypokalemia, hypochloremia, intravascular volume depletion, and urinary alkalinization. Abrupt cessation of chronic excessive bicarbonate ingestion may result in hyperkalemia, hypoaldosteronism, volume contraction, and disruption of calcium and phosphorus metabolism. The case of a patient with three hospital admissions in 4 months, all the result of excessive oral intake of bicarbonate for symptomatic relief of dyspepsia is reported. Evaluation and treatment of patients with acute bicarbonate ingestion is discussed.

Use of kaolin waste for production os soil-lime blocks

International Nuclear Information System (INIS)

Anjos, C.M. dos; Neves, G.A.

2011-01-01

There is an evident growth in waste generation over the last decades, especially in developing countries. The mining industry produces large quantities and different kinds and levels of dangerousness, such as the kaolin processing industry, which produces waste based on silica, mica and kaolinite. Disposal of this material in an inappropriate location causes significant environmental impacts, which could be minimized with the use of waste as raw material for use in construction. This paper has as main objective to study the incorporation of the kaolin processing waste into soil-lime. The residues of kaolin were calcined at a temperature of 800 ° C for evaluation of pozzolanic activity. Raw materials and conventional alternatives were characterized by means of test particle size analysis by laser diffraction, chemical analysis, X-ray diffraction. Then, blocks conventional soil-lime and soil-lime with the introduction of residual kaolin in proportions of 10%, 20%, 30% and 40% were cast and cured in a moist chamber for periods of 28, 60 and 90 days. The technological tests of compressive strength results obtained within the specifications of the ABNT. The best results were for 90 days of healing and 20% residue. (author)

Wood ash as a soil additive and liming agent

International Nuclear Information System (INIS)

Campbell, A.; Etiegni, L.; Mahler, R.L.

1991-01-01

This study evaluated wood ash as an agricultural soil supplement and liming material. Winter wheat (Triticum aestivum) and poplar (Populus sp.) were grown in a greenhouse on six different Idaho soils amended with different ash concentrations. At ash levels equal to or lower than 2%, no detrimental effects were observed. In fact, the biomass of the wheat and the caliper and height of the poplar cuttings increased more at 2% ash 940 metric tons/ha than with the control soil. These results suggest that wood ash could be used in agricultural applications as a low analysis fertilizer containing potassium and as a liming agent. Land application of wood ash could be less expensive and more environmentally sound than present landfilling practices

Preliminary observation on the effect of baking soda volume on controlling odour from discarded organic waste

International Nuclear Information System (INIS)

Qamaruz-Zaman, N.; Kun, Y.; Rosli, R.-N.

2015-01-01

Highlights: • Approximately 50 g baking soda reduced odour concentration by 70%. • Reducing volatile acid concentration reduces odour concentration. • Ammonia has less effect on odour concentration. - Abstract: Food wastes with high moisture and organic matter content are likely to emit odours as a result of the decomposition process. The management of odour from decomposing wastes is needed to sustain the interest of residents and local councils in the source separation of kitchen wastes. This study investigated the potential of baking soda (at 50 g, 75 g and 100 g per kg food waste) to control odour from seven days stored food waste. It was found that 50 g of baking soda, spread at the bottom of 8 l food wastes bin, can reduce the odour by about 70%. A higher amount (above 100 g) is not advised as a pH higher than 9.0 may be induced leading to the volatilization of odorous ammonia. This research finding is expected to benefit the waste management sector, food processing industries as well as the local authorities where malodour from waste storage is a pressing issue

Preliminary observation on the effect of baking soda volume on controlling odour from discarded organic waste

Energy Technology Data Exchange (ETDEWEB)

Qamaruz-Zaman, N., E-mail: cenastaein@usm.my; Kun, Y.; Rosli, R.-N.

2015-01-15

Highlights: • Approximately 50 g baking soda reduced odour concentration by 70%. • Reducing volatile acid concentration reduces odour concentration. • Ammonia has less effect on odour concentration. - Abstract: Food wastes with high moisture and organic matter content are likely to emit odours as a result of the decomposition process. The management of odour from decomposing wastes is needed to sustain the interest of residents and local councils in the source separation of kitchen wastes. This study investigated the potential of baking soda (at 50 g, 75 g and 100 g per kg food waste) to control odour from seven days stored food waste. It was found that 50 g of baking soda, spread at the bottom of 8 l food wastes bin, can reduce the odour by about 70%. A higher amount (above 100 g) is not advised as a pH higher than 9.0 may be induced leading to the volatilization of odorous ammonia. This research finding is expected to benefit the waste management sector, food processing industries as well as the local authorities where malodour from waste storage is a pressing issue.

CHEMISTRY OF PLANTS AND RECLAIMED GROUNDS ON SODA WASTE SITE AT JANIKOWO

Directory of Open Access Journals (Sweden)

Jan Siuta

2014-10-01

Full Text Available The paper presents the state of soda waste dumping site prior to reclamation, including the initial vegetation and properties of local grounds, the chemistry of plants colonizing the alkaline grounds in 2013 as well as the comparison of mineral element contents in leaves of trees spontaneously growing on the soda waste site in the years 2000 and 2013. The paper consists an integral part of a wider work concerning the effectiveness of sewage sludge application for bioremediation of highly saline and alkaline waste at the Janikowo Soda Plant. The spontaneous vegetation on soda waste in 2000 was scarce and patchy, its development conditioned by local microrelief where depressions provided water for plant establishment. The main species entering the site included grasses (Lolium perenne, Calamagrostis epigeios and herbs (Reseda lutea, Tussilago farfara and Picris hieracioides. The physico-chemical properties of waste grounds varied widely both horizontally and spatially. In 2013, the reclaimed dumping site was covered by a well-established meadow-likevegetation and the soil top layer (0–5 cm contained 9.2–13.9% Ca and 15–161 mg Cl/kg, at pH 7.6–7.8. The underlying 10–20 cm layer contained 21.1–63.3% Ca and 204–3110 mg Cl/kg, at pH 7.93–9.04. In the deeper 40-60 cm layer there was found 30.0-37.5% Ca and 9 920-16 320 mg Cl/kg, at pH 11.5–12.1. The vegetation growing in the vicinity of soil profiles contained: 1.65–3.36% N; 0.25–0.43% P; 1.38–2.95% K; 0.33–1.10 % Ca and 0.13–0.54% Mg. The contents of heavy metals in plants approximated the average amounts found in meadow clippings in Poland. The contents of main nutrients in leaves of trees spontaneously growing on the waste site were significantly higher in 2013 (2.70–3.21% N; 0.25–0.34% P and 0.98–1.75% K than in the year 2000 (1.70–2.04% N; 0.11–0.21% P and 0.54–0.80% K. The application of sewage sludge and subsequent fertilization of vegetation on waste

Development of New Lemon-Lime Flavored Beverage for OGTT: Acceptability and Reproducibility.

Science.gov (United States)

Chotwanvirat, Phawinpon; Thewjitcharoen, Yotsapon; Parksook, Wyn; Krittiyawong, Sirinate; Hutaphat, Kritchana; Nakasatien, Soontaree; Kaocharoen, Sming; Himathongkam, Thep

2016-05-01

The oral glucose tolerance test (OGTT) is essential procedure in both screening and diagnosis of impaired glucose tolerance (IGT), impaired fasting glucose (IFG) and diabetes mellitus (DM), but it is not easy to perform because of intense sweetness of the 75-g glucose test beverage causing abdominal discomfort post-testing. Therefore, the new formula of non-carbonated lemon-lime flavored beverage was developed to increase its palatability and better compliance. To develop a new non-carbonated lemon-lime flavored beverage to replace the standard beverage for OGTT Subsequently, the diagnostic value and acceptability between the new formula and the traditional 75-g OGTT formula were compared in healthy subjects. The new lemon-lime flavored formula was developed to replace the standard beverage for OGTT by adding 1,000 milligram of citric acid and 0.03 gram of lime flavor to 75 gram of anhydrous glucose to a final volume of 300 ml. The study was conducted in 30 healthy subjects who underwent the traditional 75-gram OGTT test and the new formula of OGTT beverage one week later, or vice versa, to access acceptability, indices markers of insulin secretion, and insulin sensitivity. Palatability was determined by rating on a 9-point Hedonic Scale. Thirty healthy subjects (15 females) with the age of 33.2 ± 7.5 years and body mass index of 22.9 ± 3.5 kg/m² were enrolled. No significant difference was found between plasma glucose in 0, 30, 60, 90, and 120 minutes, insulin level (0 and 120 minutes) and four insulin surrogate markers in both traditional 75-gram OGTT and new formula of lemon-lime flavored OGTT beverage. The overall satisfaction score of the new formula OGTT was better when compared with the scores of the traditional OGTT (7.1 ± 1.8 vs. 4.7 ± 2.0). Only one subject complained about abdominal discomfort in both episode of OGTT CONCLUSION: The modified lemon-lime flavored beverage for OGTT demonstrated better acceptance in the subjects without difference in

In-Depth Transcriptome Sequencing of Mexican Lime Trees Infected with Candidatus Phytoplasma aurantifolia.

Science.gov (United States)

Mardi, Mohsen; Karimi Farsad, Laleh; Gharechahi, Javad; Salekdeh, Ghasem Hosseini

2015-01-01

Witches' broom disease of acid lime greatly affects the production of Mexican lime in Iran. It is caused by a phytoplasma (Candidatus Phytoplasma aurantifolia). However, the molecular mechanisms that underlie phytoplasma pathogenicity and the mode of interactions with host plants are largely unknown. Here, high-throughput transcriptome sequencing was conducted to explore gene expression signatures associated with phytoplasma infection in Mexican lime trees. We assembled 78,185 unique transcript sequences (unigenes) with an average length of 530 nt. Of these, 41,805 (53.4%) were annotated against the NCBI non-redundant (nr) protein database using a BLASTx search (e-value ≤ 1e-5). When the abundances of unigenes in healthy and infected plants were compared, 2,805 transcripts showed significant differences (false discovery rate ≤ 0.001 and log2 ratio ≥ 1.5). These differentially expressed genes (DEGs) were significantly enriched in 43 KEGG metabolic and regulatory pathways. The up-regulated DEGs were mainly categorized into pathways with possible implication in plant-pathogen interaction, including cell wall biogenesis and degradation, sucrose metabolism, secondary metabolism, hormone biosynthesis and signalling, amino acid and lipid metabolism, while down-regulated DEGs were predominantly enriched in ubiquitin proteolysis and oxidative phosphorylation pathways. Our analysis provides novel insight into the molecular pathways that are deregulated during the host-pathogen interaction in Mexican lime trees infected by phytoplasma. The findings can be valuable for unravelling the molecular mechanisms of plant-phytoplasma interactions and can pave the way for engineering lime trees with resistance to witches' broom disease.

Lewis acid-catalyzed depolymerization of soda lignin in supercritical ethanol/water mixtures

NARCIS (Netherlands)

Güvenatam, Burcu; Heeres, Erik H.J.; Pidko, Evgeny A.; Hensen, Emiel J M

2016-01-01

The depolymerization of lignin model compounds and soda lignin by super Lewis acidic metal triflates has been investigated in a mixture of ethanol and water at 400 °C. The strong Lewis acids convert representative model compounds for the structure-forming linkages in lignin, namely α-O-4, 5-O-4

Sludge hygienization: Helminth eggs destruction by lime treatment Ascaris eggs as model

Energy Technology Data Exchange (ETDEWEB)

Banas, S.; Schwartzbrod, J. [Lab. de Chimie Physique et Microbiologie de l' Environnement, Nancy (France); Remy, M. [Lhoist, on behalf of the European Lime Assoication (EuLA), Bruessel (Germany); Boehm, R. [Univ. Hohenheim, Stuttgart (Germany); Verfuerden, M. [Fels-Werke GmbH, im Namen des Bundesverbandes der Deutschen Kalkindustrie (BVK), Koeln (Germany)

2003-07-01

Most pathogens in the raw sewage are concentrated into the sewage sludge. They can be separated into four categories: viruses, bacteria, protozoa and larger parasites such as human roundworms, tapeworms and liver flukes. Such micro-organisms can cause disease in humans, the transmission occurring in several ways e.g. by inhaling sludge aerosols or dust, by eating vegetables or fruits contaminated by sludge, drinking water contaminated by run-off or by eating meat from livestock infected by grazing pastures fertilised with sludge. The presence of helminth eggs in urban sludge may constitute a sanitary risk when used as agricultural fertiliser. To avoid any contamination, the efficiency of a certain number of sludge hygienization processes must be tested. One of these involves decontamination with quicklime. The Ascaris egg inactivation by liming with lime milk, slaked lime and quicklime is studied in a series of sludges coming from slaughterhouses. (orig.)

Impacts of fresh lime juice and peel on atherosclerosis progression in an animal model

Directory of Open Access Journals (Sweden)

Maryam Boshtam

2013-11-01

Full Text Available BACKGROUND: The main protective role of antioxidants in the progression of atherosclerosis has been shown in some studies. Therefore, this project evaluated the effects of Citrus aurantifolia (Christm juice and peel on antioxidant activity and atherosclerosis progression in rabbits receiving a hypercholesterolemic diet. METHODS: Forty white New Zealand male rabbits were randomly allocated to four groups. All groups were on hypercholesterolemic diet for two months. While the first group was considered as the hypercholesterolemic control, groups 2 and 3 (intervention groups received 5 ml/day lime juice and 1 g/day dried lime peel powder, respectively. Group 4 was fed a normal diet (normal control. Before and after the study, weight was measured and a fasting blood specimen was taken from the rabbits. Serum lipids analyses and antioxidant activity evaluations were then performed. The rabbits’ aorta and coronary arteries were separated and the presence of fatty streaks was studied. RESULTS: Comparing to the hypercholesterolemic control group (-25.2 ± 7.0, only the plasma total antioxidant capacity change was significantly more in rabbits supplemented with lime juice (16.3 ± 14.7 and peel (8.6 ± 7.1 (P = 0.008. The presence of fatty streaks in coronary arteries and aorta of the intervention groups [juice (0.2 ± 0.01; peel (0.0 ± 0.00] was significantly decreased compared to the hypercholesterolemic control group (1.2 ± 0.4 (P < 0.001. CONCLUSION: Based on our findings, Citrus aurantifolia peel and juice increase plasma antioxidant capacity in rabbits, and can thus prevent or decelerate the process of atherogenesis. However, lime peel is more effective than lime juice.   Keywords: Animal, Atherosclerosis, Atherogenic Diet, Fatty Streak, Intervention, Lime    Normal 0 false false false EN-US X-NONE AR-SA

Copper, nickel and zinc phytoavailability in an oxisol amended with sewage sludge and liming

Directory of Open Access Journals (Sweden)

Martins Adão Luiz Castanheiro

2003-01-01

Full Text Available Contents of heavy metal on agricultural soils have been raised by land applications of sewage sludge and may constitute a hazard to plants, animals and humans. A field experiment was carried out from 1983 to 1987, to evaluate the long-term effect of sewage sludge application, with and without liming, on heavy metal accumulation and availability in a Rhodic Hapludox soil grown with maize (HMD 7974 hybrid. Trials were set up in a completely randomized blocks design with four replications. Each block was split in two bands, one with and another without liming. The sludge was applied in each band at rates: 0, 20, 40, 60 and 80 Mg ha-1 (dry basis in a single application; and 40, 60 and 80 Mg ha-1 split in two, three and four equal yearly applications, respectively. The soil was sampled for chemical analysis each year after harvest. Soil samples were analysed for Cu, Ni and Zn in extracts obtained with DTPA and Mehlich-3 solutions, and in extracts obtained by digestion with nitric-perchloric acid (total metal contents, using an inductively coupled plasma (ICP spectrometer. In general, Zn, Cu and Ni concentrations in DTPA and Mehlich-3 extracts increased linearly with sludge application. Total Cu and Zn concentrations increased when sludge was applied, whereas total Ni concentrations were not affected. Both extractants were suitable to evaluate Cu and Zn availability to corn in the soil treated with sewage sludge. Liming reduced the DTPA extractability of Zn. DTPA-extractable Cu concentrations were not significantly affected by liming. Mehlich-3-extractable Cu and Zn concentrations increased with liming. Only DTPA extractant indicated reduction of Ni concentrations in the soil after liming.

The Soda Can Optimization Problem: Getting Close to the Real Thing

Science.gov (United States)

Premadasa, Kirthi; Martin, Paul; Sprecher, Bryce; Yang, Lai; Dodge, Noah-Helen

2016-01-01

Optimizing the dimensions of a soda can is a classic problem that is frequently posed to freshman calculus students. However, if we only minimize the surface area subject to a fixed volume, the result is a can with a square edge-on profile, and this differs significantly from actual cans. By considering a more realistic model for the can that…

Initial Examination of Low Velocity Sphere Impact of Glass Ceramics

Energy Technology Data Exchange (ETDEWEB)

Morrissey, Timothy G [ORNL; Fox, Ethan E [ORNL; Wereszczak, Andrew A [ORNL; Ferber, Mattison K [ORNL

2012-06-01

This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (< 30 m/s or < 65 mph) sphere impact testing of two materials from the lithium aluminosilicate family reinforced with different amounts of ceramic particulate, i.e., glass-ceramic materials, SCHOTT Resistan{trademark}-G1 and SCHOTT Resistan{trademark}-L. Both materials are provided by SCHOTT Glass (Duryea, PA). This work is a follow-up to similar sphere impact studies completed by the authors on PPG's Starphire{reg_sign} soda-lime silicate glass and SCHOTT BOROFLOAT{reg_sign} borosilicate glass. A gas gun or a sphere-drop test setup was used to produce controlled velocity delivery of silicon nitride (Si{sub 3}N{sub 4}) spheres against the glass ceramic tile targets. Minimum impact velocities to initiate fracture in the glass-ceramics were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between sphere and target material. Quasistatic spherical indentation was also performed on both glass ceramics and their contact damage responses were compared to those of soda-lime silicate and borosilicate glasses. Lastly, variability of contact damage response was assessed by performing spherical indentation testing across the area of an entire glass ceramic tile. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Resistan{trademark}-L glass ceramic required the highest velocity of sphere impact for damage to initiate. Starphire{reg_sign} soda-lime silicate glass was second best, then Resistan{trademark}-G1 glass ceramic, and then BOROFLOAT{reg_sign} borosilicate glass. (2) Glass-ceramic Resistan{trademark}-L also required the largest force to initiate ring crack from quasi-static indentation. That ranking was followed, in descending order, by Starphire{reg_sign} soda-lime silicate glass, Resistan{trademark}-G1 glass ceramic, and BOROFLOAT{reg_sign} borosilicate glass

Performance of Portland cement mixes containing silica fume and mixed with lime-water

Directory of Open Access Journals (Sweden)

Metwally A.A. Abd Elaty

2014-12-01

Test results show that using lime-water in mixing enhances consistency degree compared to the corresponding control mixes. Furthermore, it delays both initial and final setting times compared with traditional water due to the common ion effect principles. Moreover, combined use of lime-water and silica fume enhances the pozzolanic reaction that was identified by the strength development at both early and later ages. The existence of CH crystals for higher percentages of silica fume (up to 30% for further reaction at later ages was observed by XRD results. Moreover, combined use of silica fume and lime-water ensures a high alkaline media around steel bars from the moment of ingredients mixing as long as later ages despite of pozzolanic reaction that was identified from results of chloride attack.

EVALUATION OF BIOAEROSOL COMPONENTS, GENERATION FACTORS, AND AIRBORNE TRANSPORT ASSOCIATED WITH LIME TREATMENT OF CONTAMINATED SEDIMENT

Science.gov (United States)

Lime treatment has been used in contaminated sediment management activities for many purposes such as dewatering, improvement of physical properties, and reducing contaminant mobility. Exothermic volatilization of volatile organic compounds from lime-treated sediment is well kno...

Crack velocity measurement by induced electromagnetic radiation

International Nuclear Information System (INIS)

Frid, V.; Rabinovitch, A.; Bahat, D.

2006-01-01

Our model of electromagnetic radiation (EMR) emanated from fracture implies that EMR amplitude is proportional to crack velocity. Soda lime glass samples were tested under uniaxial tension. Comparison of crack velocity observed by Wallner line analysis and the peak amplitude of EMR signals registered during the test, showed very good correlation, validating this proportionality

Crack velocity measurement by induced electromagnetic radiation

Energy Technology Data Exchange (ETDEWEB)

Frid, V. [Deichmann Rock Mechanics Laboratory of the Negev, Geological and Environmental Sciences Department, Ben Gurion University of the Negev, Beer Sheva (Israel)]. E-mail: vfrid@bgu.ac.il; Rabinovitch, A. [Deichmann Rock Mechanics Laboratory of the Negev, Physics Department, Ben Gurion University of the Negev, Beer Sheva (Israel); Bahat, D. [Deichmann Rock Mechanics Laboratory of the Negev, Geological and Environmental Sciences Department, Ben Gurion University of the Negev, Beer Sheva (Israel)

2006-07-31

Our model of electromagnetic radiation (EMR) emanated from fracture implies that EMR amplitude is proportional to crack velocity. Soda lime glass samples were tested under uniaxial tension. Comparison of crack velocity observed by Wallner line analysis and the peak amplitude of EMR signals registered during the test, showed very good correlation, validating this proportionality.

An Aerobic Digestion of Lime Sludge.

Science.gov (United States)

1982-07-01

removal. 1,2 After lime addition, phosphorus is considered to be in the form of calcium hydroxyapatite (Ca5-(OH)(P04 )3 ), which will not resolubilize...U: c a e - ~ -’ tr *cr. V. (r. C . -~~~ C c C C&c cj Ir u -. C Fy. - U C C - C F.~-cc 0.c gC - - gg MFC - - C -66 TABLE 20. SUMMARY OF LEAST

Influence of liming substances and temperature on microbial activity and leaching of soil organic matter in coniferous forest ecosystems

International Nuclear Information System (INIS)

Andersson, Stefan

1999-01-01

Liming has been proposed as a means to counteract the anthropogenic acidification of forest soils in Sweden. The increased pH caused by liming may affect the production and leaching of dissolved organic matter (DOM) from the mor humus layer. The aim of this thesis was to assess changes in leaching of dissolved organic carbon (DOC) and nitrogen (DON) and microbial activity in relation to liming. Leaching experiments were carried out in the laboratory with incubated field-limed soils and by monitoring of dissolved components in lysimeter water collected in a field liming experiment in southern Sweden from 1992-1997. Liming increased the leaching of DOC and DON from the mor humus layer but in the B horizon there were indications of different adsorption properties of DON compared to DOC, which affected the leaching of DOC and DON from the B horizon. DOC leaching was mainly regulated by temperature in mor humus from a site in southern Sweden, while pH had a greater effect in mor humus from a site in northern Sweden. This may have been due to relatively higher bacterial growth in the limed mor humus from southern Sweden. The experiments indicated that bacteria had a decisive role in the microbial production of DOM and bacterial activity was stimulated more by the increase in pH than by the change in the chemical composition of DOM after liming. Field data indicated that increasedCO 2 respiration in the limed treatment decreased carbon storage in the mor humus layer. There may have been an increase in carbon and nitrogen storage in the B horizon due to an increased adsorption caused by the higher leaching of DOM from the mor humus layer. The changes in storage could not be confirmed statistically, but there was a significant decline in the C/N ratio in the mor humus layer in the limed treatment. The adsorption patterns of DOC and DON indicated in the field were confirmed in a laboratory experiment