Properties of bacterial radioresistance observed in sewage sludge

Energy Technology Data Exchange (ETDEWEB)

Watanabe, H; Ito, H; Takehisa, M [Japan Atomic Energy Research Inst., Takasaki, Gunma. Takasaki Radiation Chemistry Research Establishment; Iizuka, H

1981-09-01

The changes in radiosensitivities of bacteria in sludge were investigated. The coliforms are more radioresistant in raw sludge than in cake (dewatered sludge). This radioresistance of coliforms was observed not only in raw sludge but also in the cake diluted with water. The radioresistance was independent of the difference of treatment plant, kind of sludge, and season. The oxygen effect on the radioresistance was not observed, but the resistance was changed during storage of sludge. Escherichia coli isolated from sludge was radiosensitive in buffer, but its radiosensitivity was protected by the water-extracts of sludge. On the other hand, radioresistant bacteria were present in total bacteria of sludge irradiated at 2 Mrad. However, the dominant flora in the irradiated sludge consisted of radiosensitive bacteria (mainly Pseudomonas). When a strain of radiosensitive Pseudomonas was irradiated in raw sludge and diluted cake, the radiosensitivity was remarkably protected. From these results, it is suggested that a factor affecting the radiosensitivity of bacteria is present in sludge.

Properties of bacterial radioresistance observed in sewage sludge

International Nuclear Information System (INIS)

Watanabe, Hiroshi; Ito, Hitoshi; Takehisa, Masaaki; Iizuka, Hiroshi.

1981-01-01

The changes in radiosensitivities of bacteria in sludge were investigated. The coliforms are more radioresistant in raw sludge than in cake (dewatered sludge). This radioresistance of coliforms was observed not only in raw sludge but also in the cake diluted with water. The radioresistance was independent of the difference of treatment plant, kind of sludge, and season. The oxygen effect on the radioresistance was not observed, but the resistance was changed during storage of sludge. Escherichia coli isolated from sludge was radiosensitive in buffer, but its radiosensitivity was protected by the water-extracts of sludge. On the other hand, radioresistant bacteria were present in total bacteria of sludge irradiated at 2 Mrad. However, the dominant flora in the irradiated sludge consisted of radiosensitive bacteria (mainly Pseudomonas). When a strain of radiosensitive Pseudomonas was irradiated in raw sludge and diluted cake, the radiosensitivity was remarkably protected. From these results, it is suggested that a factor affecting the radiosensitivity of bacteria is present in sludge. (author)

Bacterial composition of activated sludge - importance for floc and sludge properties

Energy Technology Data Exchange (ETDEWEB)

Nielsen, Per H.; Thomsen, Trine R.; Nielsen, Jeppe L.

2003-07-01

Activated sludge flocs consist of numerous constituents which, together with other factors, are responsible for floc structure and floc properties. These properties largely determine the sludge properties such as flocculation, settling and dewaterability. In this paper we briefly review the present knowledge about the role of bacteria in relation to floc and sludge properties, and we present a new approach to investigate the identity and function of the bacteria in the activated sludge flocs. The approach includes identification of the important bacteria and a characterization of their physiological and functional properties. It is carried out by use of culture-independent molecular biological methods linked with other methods to study the physiology and function maintaining a single cell resolution. Using this approach it was found that floc-forming properties differed among the various bacterial groups, e.g. that different microcolony-forming bacteria had very different sensitivities to shear and that some of them deflocculated under anaerobic conditions. in our opinion, the approach to combine identity with functional analysis of the dominant bacteria in activated sludge by in situ methods is a very promising way to investigate correlations between presence of specific bacteria, and floc and sludge properties that are of interest. (author)

Biosorption of Cd, Cr, Mn, and Pb from aqueous solutions by Bacillus sp strains isolated from industrial waste activate sludge

OpenAIRE

García, Rocío; Campos, Juan; Cruz, Julio Alfonso; Calderón, Ma. Elena; Raynal, Ma. Elena; Buitrón, Germán

2016-01-01

Abstract The microorganisms are capable of accumulating heavy metal ions from water as biosorbent agents, offering a potential alternative for the detoxification and recovery of toxic/precious metals in industrial wastewater. In the present work, metal-resistant bacterial strains were isolated and identified from activated sludge of a waste treatment plant in the Municipality of Santa Rosa Jauregui, Querétaro. To obtain bacteria tolerant to metals, 37 bacterial strains and two isolates were s...

Molecular characterization of a Xylanase-producing fungus isolated from fouled soil

Directory of Open Access Journals (Sweden)

Punniavan Sakthiselvan

2014-12-01

Full Text Available Xylanase (EC 3. 2. 1. 8, hydrolyzes xylo-oligosaccharides into D-xylose and required for complete hydrolysis of native cellulose and biomass conversion. It has broad range of applications in the pulp and paper, pharmaceutical and Agri-food industries. Fifty fungal species were isolated from the fouled soil around an oil refinery and screened for the production of xylanase enzyme by enrichment culture techniques. The isolated fungal strain was identified as Hypocrea lixii SS1 based on the results of biochemical tests and 18s rRNA sequencing. The phylogenetic tree was constructed using the MEGA 5 software. Further, Hypocrea lixii SS1 was tested for the ability to utilize the sunflower oil sludge (waste from the oil industry as the sole carbon source for xylanase production. The growth characteristics of Hypocrea lixii SS1 were also studied and maximum growth was found on the 7th day of incubation. The fungus showed a remarkable xylanase production of 38.9 U/mL. Xylanase was purified using a combination of 0-50% NH4SO2 precipitation, DEAE-sepharose and Sephacryl S-200 chromatography. Single peak obtained in RP-HPLC confirms the purity of xylanase. Further the enzyme produced was affirmed as xylanase with its molecular weight (29 kDa using SDS-PAGE.

Toxic influence of silver and uranium salts on activated sludge of wastewater treatment plants and synthetic activated sludge associates modeled on its pure cultures.

Science.gov (United States)

Tyupa, Dmitry V; Kalenov, Sergei V; Skladnev, Dmitry A; Khokhlachev, Nikolay S; Baurina, Marina M; Kuznetsov, Alexander Ye

2015-01-01

Toxic impact of silver and uranium salts on activated sludge of wastewater treatment facilities has been studied. Some dominating cultures (an active nitrogen fixer Agrobacterium tumifaciens (A.t) and micromyces such as Fusarium nivale, Fusarium oxysporum, and Penicillium glabrum) have been isolated and identified as a result of selection of the activated sludge microorganisms being steadiest under stressful conditions. For these cultures, the lethal doses of silver amounted 1, 600, 50, and 300 µg/l and the lethal doses of uranium were 120, 1,500, 1,000, and 1,000 mg/l, respectively. A.tumifaciens is shown to be more sensitive to heavy metals than micromyces. Synthetic granular activated sludge was formed on the basis of three cultures of the isolated micromyces steadiest against stress. Its granules were much more resistant to silver than the whole native activated sludge was. The concentration of silver causing 50 % inhibition of synthetic granular activated sludge growth reached 160-170 μg/l as far as for the native activated sludge it came only to 100-110 μg/l.

Zinc bioaccumulation by microbial consortium isolated from nickel smelter sludge disposal site

Directory of Open Access Journals (Sweden)

Kvasnová Simona

2017-06-01

Full Text Available Heavy metal pollution is one of the most important environmental issues of today. Bioremediation by microorganisms is one of technologies extensively used for pollution treatment. In this study, we investigated the heavy metal resistance and zinc bioaccumulation by microbial consortium isolated from nickel sludge disposal site near Sereď (Slovakia. The composition of consortium was analyzed based on MALDI-TOF MS of cultivable bacteria and we have shown that the consortium was dominated by bacteria of genus Arthrobacter. While consortium showed very good growth in the zinc presence, it was able to remove only 15 % of zinc from liquid media. Selected members of consortia have shown lower growth rates in the zinc presence but selected isolates have shown much higher bioaccumulation abilities compared to whole consortium (up to 90 % of zinc removal for NH1 strain. Bioremediation is frequently accelerated through injection of native microbiota into a contaminated area. Based on data obtained in this study, we can conclude that careful selection of native microbiota could lead to the identification of bacteria with increased bioaccumulation abilities.

In situ detection, isolation, and physiological properties of a thin filamentous microorganism abundant in methanogenic granular sludges: a novel isolate affiliated with a clone cluster, the green non-sulfur bacteria, subdivision I.

Science.gov (United States)

Sekiguchi, Y; Takahashi, H; Kamagata, Y; Ohashi, A; Harada, H

2001-12-01

We previously showed that very thin filamentous bacteria affiliated with the division green non-sulfur bacteria were abundant in the outermost layer of thermophilic methanogenic sludge granules fed with sucrose and several low-molecular-weight fatty acids (Y. Sekiguchi, Y. Kamagata, K. Nakamura, A. Ohashi, H. Harada, Appl. Environ. Microbiol. 65:1280-1288, 1999). Further 16S ribosomal DNA (rDNA) cloning-based analysis revealed that the microbes were classified within a unique clade, green non-sulfur bacteria (GNSB) subdivision I, which contains a number of 16S rDNA clone sequences from various environmental samples but no cultured representatives. To investigate their function in the community and physiological traits, we attempted to isolate the yet-to-be-cultured microbes from the original granular sludge. The first attempt at isolation from the granules was, however, not successful. In the other thermophilic reactor that had been treating fried soybean curd-manufacturing wastewater, we found filamentous microorganisms to outgrow, resulting in the formation of projection-like structures on the surface of granules, making the granules look like sea urchins. 16S rDNA-cloning analysis combined with fluorescent in situ hybridization revealed that the projections were comprised of the uncultured filamentous cells affiliated with the GNSB subdivision I and Methanothermobacter-like cells and the very ends of the projections were comprised solely of the filamentous cells. By using the tip of the projection as the inoculum for primary enrichment, a thermophilic, strictly anaerobic, filamentous bacterium, designated strain UNI-1, was successfully isolated with a medium supplemented with sucrose and yeast extract. The strain was a very slow growing bacterium which is capable of utilizing only a limited range of carbohydrates in the presence of yeast extract and produced hydrogen from these substrates. The growth was found to be significantly stimulated when the strain was

Bacteriology of activated sludge

NARCIS (Netherlands)

Gils, van H.W.

1964-01-01

The bacteriology and biochemistry of activated sludge grown in domestic waste water or fed with synthetic media were studied. The nature of the flocs was investigated by determining morphological and physiological characteristics of many strains isolated.

Predominant bacteria were

Selection of diazotrophic bacteria isolated from wastewater treatment plant sludge at a poultry slaughterhouse for their effect on maize plants

Directory of Open Access Journals (Sweden)

Jorge Avelino Rodriguez Lozada

Full Text Available ABSTRACT The economic and environmental costs of nitrogen fertilization have intensified the search for technologies that reduce mineral fertilization, for example atmospheric nitrogen-fixing (diazotrophic bacteria inoculation. In this context, the present study addressed the isolation and quantification of diazotrophic bacteria in the sludge from treated wastewater of a poultry slaughterhouse; a description of the bacteria, based on cell and colony morphology; and an assessment of growth and N content of maize plants in response to inoculation. Sixteen morphotypes of bacteria were isolated in six N-free culture media (JMV, JMVL, NFb, JNFb, LGI, and LGI-P. The bacteria stained gram-positive, with 10 rod- and six coccoid-shaped isolates. To evaluate the potential of bacteria to promote plant growth, maize seeds were inoculated. The experiment consisted of 17 treatments (control plus 16 bacterial isolates and was carried out in a completely randomized design with six replicates. The experimental units consisted of one pot containing two maize plants in a greenhouse. Forty-five days after planting, the variables plant height, leaf number, stem diameter, root and shoot fresh and dry weight, and N content were measured. The highest values were obtained with isolate UFV L-162, which produced 0.68 g total dry matter per plant and increased N content to 22.14 mg/plant, representing increments of 74 and 133%, respectively, compared with the control. Diazotrophs inhabit sludge from treated wastewater of poultry slaughterhouses and can potentially be used to stimulate plant development and enrich inoculants.

Experience with a pilot plant for the irradiation of sewage sludge: Experiments on the inactivation of viruses in sewage sludge after radiation treatment

International Nuclear Information System (INIS)

Epp, C.

1975-01-01

Investigations examining the virus inactivating effect of a 60 Co-plant have up to now been limited to attempts to isolate virus from sludge samples taken from sewage sludge before and after irradiation with 300 krad. As in these sludge samples the presence of virus could be proved only on a rather irregular basis, an experiment was carried out in which defined virus quantities were packed into capsules and mixed with the digested sludge. At the end of the hygienization process these capsules were removed from the sludge and examined for virus content. In addition one radiation volume (5.6 m 3 ) was infected with attenuated polio virus type I and the virus content of the sludge titrated before and after the radiation treatment. (author)

Synthetic fibers as an indicator of land application of sludge

International Nuclear Information System (INIS)

Zubris, Kimberly Ann V.; Richards, Brian K.

2005-01-01

Synthetic fabric fibers have been proposed as indicators of past spreading of wastewater sludge. Synthetic fiber detectability was examined in sludges (dewatered, pelletized, composted, alkaline-stabilized) and in soils from experimental columns and field sites applied with those sludge products. Fibers (isolated by water extraction and examined using polarized light microscopy) were detectable in sludge products and in soil columns over 5 years after application, retaining characteristics observed in the applied sludge. Concentrations mirrored (within a factor of 2) predictions based on soil dilution. Fibers were detectable in field site soils up to 15 years after application, again retaining the characteristics seen in sludge products. Concentrations correlated with residual sludge metal concentration gradients in a well-characterized field site. Fibers found along preferential flow paths and/or in horizons largely below the mixed layer suggest some potential for translocation. Synthetic fibers were shown to be rapid and semi-quantitative indicators of past sludge application. - Synthetic fabric fibers present in wastewater sludge are a semi-quantitative long-term indicator of past sludge application in soils

Soil microbial functional and fungal diversity as influenced by municipal sewage sludge accumulation.

Science.gov (United States)

Frąc, Magdalena; Oszust, Karolina; Lipiec, Jerzy; Jezierska-Tys, Stefania; Nwaichi, Eucharia Oluchi

2014-08-28

Safe disposal of municipal sewage sludge is a challenging global environmental concern. The aim of this study was to assess the response of soil microbial functional diversity to the accumulation of municipal sewage sludge during landfill storage. Soil samples of a municipal sewage sludge (SS) and from a sewage sludge landfill that was 3 m from a SS landfill (SS3) were analyzed relative to an undisturbed reference soil. Biolog EcoPlatesTM were inoculated with a soil suspension, and the Average Well Color Development (AWCD), Richness (R) and Shannon-Weaver index (H) were calculated to interpret the results. The fungi isolated from the sewage sludge were identified using comparative rDNA sequencing of the LSU D2 region. The MicroSEQ® ID software was used to assess the raw sequence files, perform sequence matching to the MicroSEQ® ID-validated reference database and create Neighbor-Joining trees. Moreover, the genera of fungi isolated from the soil were identified using microscopic methods. Municipal sewage sludge can serve as a habitat for plant pathogens and as a source of pathogen strains for biotechnological applications.

Study of the Mechanical Properties and Vibration Isolation Performance of a Molecular Spring Isolator

Directory of Open Access Journals (Sweden)

Muchun Yu

2016-01-01

Full Text Available Molecular Spring Isolator (MSI is a novel passive vibration isolation technique, providing High-Static-Low-Dynamic (HSLD stiffness based on the use of molecular spring material. The molecular spring material is a solid-liquid mixture consisting of water and hydrophobic nanoporous materials. Under a certain level of external pressure, water molecules can intrude into the hydrophobic pores of nanoporous materials, developing an additional solid-liquid interface. Such interfaces are able to store, release, and transform mechanical energy, providing properties like mechanical spring. Having been only recently developed, the basic mechanic properties of a MSI have not been studied in depth. This paper focuses on the stiffness influence factors, the dynamic frequency response, and the vibration isolation performance of a MSI; these properties help engineers to design MSIs for different engineering applications. First, the working mechanism of a MSI is introduced from a three-dimensional general view of the water infiltration massive hydrophobic nanoporous pores. Next, a wide range of influence factors on the stiffness properties of MSI are studied. In addition, the frequency response functions (FRFs of the MSI vibration isolation system are studied utilizing the matching method based on equivalent piecewise linear (EPL system. Finally, the vibration isolation properties of MSI are evaluated by force transmissibility.

Protein Recovery from Secondary Paper Sludge and Its Potential Use as Wood Adhesive

Science.gov (United States)

Pervaiz, Muhammad

Secondary sludge is an essential part of biosolids produced through the waste treatment plant of paper mills. Globally paper mills generate around 3.0 million ton of biosolids and in the absence of beneficial applications, the handling and disposal of this residual biomass poses a serious environmental and economic proposition. Secondary paper sludges were investigated in this work for recovery of proteins and their use as wood adhesive. After identifying extracellular polymeric substances as adhesion pre-cursors through analytical techniques, studies were carried out to optimize protein recovery from SS and its comprehensive characterization. A modified physicochemical protocol was developed to recover protein from secondary sludge in substantial quantities. The combined effect of French press and sonication techniques followed by alkali treatment resulted in significant improvement of 44% in the yield of solubilized protein compared to chemical methods. The characterization studies confirmed the presence of common amino acids in recovered sludge protein in significant quantities and heavy metal concentration was reduced after recovery process. The sodium dodecyl sulfate polyacrylamide gel electrophoresis analysis revealed the presence of both low and high molecular weight protein fractions in recovered sludge protein. After establishing the proof-of-concept in the use of recovered sludge protein as wood adhesive, the bonding mechanism of protein adhesives with cellulose substrate was further elucidated in a complementary protein-modification study involving soy protein isolate and its glycinin fractions. The results of this study validated the prevailing bonding theories by proving that surface wetting, protein structure, and type of wood play important role in determining final adhesive strength. Recovered sludge protein was also investigated for its compatibility to formulate hybrid adhesive blends with formaldehyde and bio-based polymers. Apart from chemical

Hydrothermal Testing of K Basin Sludge and N Reactor Fuel at Sludge Treatment Project Operating Conditions

Energy Technology Data Exchange (ETDEWEB)

Delegard, Calvin H.; Schmidt, Andrew J.; Thornton, Brenda M.

2007-03-30

The Sludge Treatment Project (STP), managed for the U. S. DOE by Fluor Hanford (FH), was created to design and operate a process to eliminate uranium metal from K Basin sludge prior to packaging for Waste Isolation Pilot Plant (WIPP). The STP process uses high temperature liquid water to accelerate the reaction, produce uranium dioxide from the uranium metal, and safely discharge the hydrogen. Under nominal process conditions, the sludge will be heated in pressurized water at 185°C for as long as 72 hours to assure the complete reaction (corrosion) of up to 0.25-inch diameter uranium metal pieces. Under contract to FH, the Pacific Northwest National Laboratory (PNNL) conducted bench-scale testing of the STP hydrothermal process in November and December 2006. Five tests (~50 ml each) were conducted in sealed, un-agitated reaction vessels under the hydrothermal conditions (e.g., 7 to 72 h at 185°C) of the STP corrosion process using radioactive sludge samples collected from the K East Basin and particles/coupons of N Reactor fuel also taken from the K Basins. The tests were designed to evaluate and understand the chemical changes that may be occurring and the effects that any changes would have on sludge rheological properties. The tests were not designed to evaluate engineering aspects of the process. The hydrothermal treatment affected the chemical and physical properties of the sludge. In each test, significant uranium compound phase changes were identified, resulting from dehydration and chemical reduction reactions. Physical properties of the sludge were significantly altered from their initial, as-settled sludge values, including, shear strength, settled density, weight percent water, and gas retention.

Microbial enhanced separation of oil from a petroleum refinery sludge.

Science.gov (United States)

Joseph, P J; Joseph, Ammini

2009-01-15

Petroleum refineries around the world have adopted different technological options to manage the solid wastes generated during the refining process and stocking of crude oil. These include physical, chemical and biological treatment methods. In this investigation bacterial mediated oil separation is effected. Two strains of Bacillus were isolated from petroleum-contaminated soils, and inoculated into slurry of sludge, and sludge-sand combinations. The bacteria could effect the separation of oil so as to form a floating scum within 48h with an efficiency of 97% at < or =5% level of sludge in the sludge-sand mixture. The activity was traced to the production of biosurfactants by bacteria.

Identification of selected microorganisms from activated sludge capable of benzothiazole and benzotriazole transformation.

Science.gov (United States)

Kowalska, Katarzyna; Felis, Ewa

2015-01-01

Benzothiazole (BT) and benzotriazole (BTA) are present in the environment - especially in urban and industrial areas, usually as anthropogenic micropollutants. BT and BTA have been found in the municipal and industrial wastewater, rivers, soil, groundwater, sediments and sludge. The origins of those substances' presence in the environment are various industry branches (food, chemical, metallurgical, electrical), households and surface runoff from industrial areas. Increasingly strict regulations on water quality and the fact that the discussed compounds are poorly biodegradable, make them a serious problem in the environment. Considering this, it is important to look for environmentally friendly and socially acceptable ways to remove BT and BTA. The aim of this study was to identify microorganisms capable of BT and BTA transformation or/and degradation in aquatic environment. Selected microorganisms were isolated from activated sludge. The identification of microorganisms capable of BT and BTA removal was possible using molecular biology techniques (PCR, DNA sequencing). Among isolated microorganisms of activated sludge are bacteria potentially capable of BT and BTA biotransformation and/or removal. The most common bacteria capable of BT and BTA transformation were Rhodococcus sp., Enterobacter sp., Arthrobacter sp. They can grow in a medium with BT and BTA as the only carbon source. Microorganisms previously adapted to the presence of the studied substances at a concentration of 10 mg/l, showed a greater rate of growth of colonies on media than microorganisms unconditioned to the presence of such compounds. Results of the biodegradation test suggest that BT was degraded to a greater extent than BTA, 98-100% and 11-19%, respectively.

Biochemical and molecular genetic studies on some cyanobacterial isolates

International Nuclear Information System (INIS)

Kamal, E.A.R.; Ebrahim, S.A.A.

2011-01-01

In the present study, the isolation and purification of a set of Cyanobacteria strains belonging to genus Oscillatoria was undertaken, followed by the analyses of phylogenetic relationships using different biochemical and molecular genetic techniques (SOS-PAGE and RAPO-PCR). A total of 45 protein bands were observed within the studied Osci/latoria isolates by SOS-PAGE (only three unique bands, eight monomorphic bands and 37 polymorphic bands). On the other hand, extracted ONA from isolates was used to identify the molecular fingerprints. A sum of 94 polymorphic bands was generated by these primers in the Ocsi/laloria genotypes under study. A total of 20 unique bands were identified out of the polymorphic ones. These unique bands were used to discriminate among the studied Ocsi/latoria isolates. Most isolates of Ocsi/latoria genotypes were discriminated by one or more unique bands. Numerical taxonomic using 45 protein attributes of 19 isolates and RAPO markers on five isolates. Two methods -Clustering (UPGMA) and Principal Component Analysis (PCA) were used for these analyses. The similarities and clusters produced between the studied isolates were discussed.

Biochemical and molecular genetic studies on some cyanobacterial isolates

Energy Technology Data Exchange (ETDEWEB)

Kamal, E A.R. [Umm Al-Qura University, Makkah (Saudi Arabia). Dept. of Biology; Ebrahim, S A.A. [Ain Sham University, Cairo (Egypt). Dept. of Cytogenetic

2011-11-15

In the present study, the isolation and purification of a set of Cyanobacteria strains belonging to genus Oscillatoria was undertaken, followed by the analyses of phylogenetic relationships using different biochemical and molecular genetic techniques (SOS-PAGE and RAPO-PCR). A total of 45 protein bands were observed within the studied Osci/latoria isolates by SOS-PAGE (only three unique bands, eight monomorphic bands and 37 polymorphic bands). On the other hand, extracted ONA from isolates was used to identify the molecular fingerprints. A sum of 94 polymorphic bands was generated by these primers in the Ocsi/laloria genotypes under study. A total of 20 unique bands were identified out of the polymorphic ones. These unique bands were used to discriminate among the studied Ocsi/latoria isolates. Most isolates of Ocsi/latoria genotypes were discriminated by one or more unique bands. Numerical taxonomic using 45 protein attributes of 19 isolates and RAPO markers on five isolates. Two methods -Clustering (UPGMA) and Principal Component Analysis (PCA) were used for these analyses. The similarities and clusters produced between the studied isolates were discussed.

Near-bottom pelagic bacteria at a deep-water sewage sludge disposal site

Energy Technology Data Exchange (ETDEWEB)

Takizawa, M.; Straube, W.L.; Hill, R.T.; Colwell, R.R.

1994-01-01

The epibenthic bacterial community at deep-ocean sewage sludge disposal site DWD-106, located approximately 106 miles (ca. 196 km) off the coast of New Jersey, was assessed for changes associated with the introduction of large amounts of sewage sludge. Mixed cultures and bacterial isolates obtained from water overlying sediment core samples collected at the deep-water (2,500 m) municipal sewage disposal site were tested for the ability to grow under in situ conditions of temperature and pressure. The responses of cultures collected at a DWD-106 station heavily impacted by sewage sludge were compared with those of samples collected from a station at the same depth which was not contaminated by sewage sludge. Significant differences were observed in the ability of mixed bacterial cultures and isolates from the two sites to grow under deep-sea pressure and temperature conditions. The levels of sludge contamination were established by enumerating Clostridium perfringens, a sewage indicator bacterium, in sediment samples from the two sites. (Copyright (c) 1993, American Society for Microbiology.)

Soil Microbial Functional and Fungal Diversity as Influenced by Municipal Sewage Sludge Accumulation

Directory of Open Access Journals (Sweden)

Magdalena Frąc

2014-08-01

Full Text Available Safe disposal of municipal sewage sludge is a challenging global environmental concern. The aim of this study was to assess the response of soil microbial functional diversity to the accumulation of municipal sewage sludge during landfill storage. Soil samples of a municipal sewage sludge (SS and from a sewage sludge landfill that was 3 m from a SS landfill (SS3 were analyzed relative to an undisturbed reference soil. Biolog EcoPlatesTM were inoculated with a soil suspension, and the Average Well Color Development (AWCD, Richness (R and Shannon-Weaver index (H were calculated to interpret the results. The fungi isolated from the sewage sludge were identified using comparative rDNA sequencing of the LSU D2 region. The MicroSEQ® ID software was used to assess the raw sequence files, perform sequence matching to the MicroSEQ® ID-validated reference database and create Neighbor-Joining trees. Moreover, the genera of fungi isolated from the soil were identified using microscopic methods. Municipal sewage sludge can serve as a habitat for plant pathogens and as a source of pathogen strains for biotechnological applications.

Soil Microbial Functional and Fungal Diversity as Influenced by Municipal Sewage Sludge Accumulation

Science.gov (United States)

Frąc, Magdalena; Oszust, Karolina; Lipiec, Jerzy; Jezierska-Tys, Stefania; Nwaichi, Eucharia Oluchi

2014-01-01

Safe disposal of municipal sewage sludge is a challenging global environmental concern. The aim of this study was to assess the response of soil microbial functional diversity to the accumulation of municipal sewage sludge during landfill storage. Soil samples of a municipal sewage sludge (SS) and from a sewage sludge landfill that was 3 m from a SS landfill (SS3) were analyzed relative to an undisturbed reference soil. Biolog EcoPlatesTM were inoculated with a soil suspension, and the Average Well Color Development (AWCD), Richness (R) and Shannon-Weaver index (H) were calculated to interpret the results. The fungi isolated from the sewage sludge were identified using comparative rDNA sequencing of the LSU D2 region. The MicroSEQ® ID software was used to assess the raw sequence files, perform sequence matching to the MicroSEQ® ID-validated reference database and create Neighbor-Joining trees. Moreover, the genera of fungi isolated from the soil were identified using microscopic methods. Municipal sewage sludge can serve as a habitat for plant pathogens and as a source of pathogen strains for biotechnological applications. PMID:25170681

Molecular identification of clinical Nocardia isolates from India.

Science.gov (United States)

Rudramurthy, Shivaprakash M; Honnavar, Prasanna; Kaur, Harsimran; Samanta, Palash; Ray, Pallab; Ghosh, Anup; Chakrabarti, Arunaloke

2015-10-01

The epidemiology of nocardiosis is evolving with increasing number of Nocardia spp. causing human infection. In recent years, molecular techniques have been used to identify Nocardia spp. There are limited data available on the spectrum of Nocardia spp. isolated from clinical samples in India. Here, a molecular study was carried on 30 clinical isolates maintained in our National Culture Collection to evaluate the techniques used for identifying the agents. The isolates were identified by sequencing two promising genes: the 16S rRNA gene and hsp65. Both hsp65 and the 16S rRNA gene could reliably identify 90 % of Nocardia isolates, i.e. N. farcinica, N. cyriacigeorgica, N. brasiliensis, N. otitidiscaviarum, N. amamiensis and N. pneumoniae. The mean percentage dissimilarity of sequence identification was higher using the hsp65 gene (4 %, range 0-7.9 %) compared with the 16S rRNA gene (2.3 %, range 0-8.9 %). Two isolates that showed ambiguous results in both the short segment of the 16S rRNA gene and hsp65 sequences could be resolved by sequencing a larger fragment (∼1000 bp) of the 16S rRNA gene. Both of these isolates were identified as N. beijingensis with similarities of 99.8 and 100 % compared with the standard strain. Genotyping of N. cyriacigeorgica strains was performed using hsp65 gene sequences and compared with previously described genotypes. Our N. cyriacigeorgica isolates belonged to genotype 1 (n = 4) and genotype 2 (n = 2). The present study highlights a wide spectrum of Nocardia spp. in India and emphasizes the need for molecular techniques for identification to the species level.

Partial Molecular Characterization Of Cowpea Stunt Isolates Of ...

African Journals Online (AJOL)

Partial molecular characterization of the coat protein of the cowpea stunt-causing isolates of Cucumber Mosaic Virus (CMV) from Arkansas and Georgia revealed that both isolates of CMV belong to CMV subgroup I and differ at eight nucleotides positions, resulting in two amino acids difference. There was only one amino ...

Molecular characterization of Prunus necrotic ringspot virus isolated from rose in Brazil.

OpenAIRE

FAJARDO, T. V. M.; NASCIMENTO, M. B.; EIRAS, M.; NICKEL, O.; PIO-RIBEIRO, G.

2016-01-01

ABSTRACT: There is no molecular characterization of Brazilian isolates of Prunus necrotic ringspot virus (PNRSV), except for those infecting peach. In this research, the causal agent of rose mosaic was determined and the movement (MP) and coat (CP) protein genes of a PNRSV isolate from rose were molecularly characterized for the first time in Brazil. The nucleotide and deduced amino acid sequences of MP and CP complete genes were aligned and compared with other isolates. Molecular analysis of...

The survival of pathogens in soil treated with wastewater sludge and in potatoes grown in such soil.

Science.gov (United States)

Chale-Matsau, J R B; Snyman, H G

2006-01-01

The prevalence of pathogens on potatoes (Solanum tuberosum) grown in soil amended with a pathogen rich wastewater sludge was investigated. Bacteria of the family Enterobacteriaceae are important pathogens causing intestinal and systemic illness of humans and other animals. Type B sludge was used. Sludges investigated are the high metal and the low metal sludges. Microorganisms in the sludge-amended soil were using culture-based technique. Salmonella and E. coli were observed in tested soil samples. No microorganisms were isolated from control samples taken throughout the process of the experiment. At harvest time, some of the potato samples from LMS soil were contaminated. These potatoes were subjected to further investigation using molecular techniques (polymerase chain reaction) with fD1 and rP2 as primers. Organisms identified from the sequenced potato peel samples with the BLAST search tool included Enterobacter agglomerans (Pantoea agglomerans), several Buttiauxella spp., Pectobacterium spp., Erwinia spp. and a few Pantoea spp. Other than the E. agglomerans, which is commonly found in the gut and upper respiratory tract of humans and in the environment, all the other species identified were found to be mainly either plant or soil pathogens. The E. agglomerans are not primary pathogens but secondary opportunistic pathogens particularly in immunocompromised individuals. These results suggest that growing high risk crops using wastewater sludge contaminated soil may lead to limited infestation of produce with primary pathogens. It appears that the use of HMS due to early pathogen die-off provides less risk of infection than the LMS. However, proper treatment of wastewater sludge to reduce pathogen load is essential prior to its use as soil conditioner.

Bacteriological studies on dairy waste activated sludge

NARCIS (Netherlands)

Adamse, A.D.

1966-01-01

Dairy-waste activated sludge was examined for bacterial composition and response to different conditions. Strains isolated were classified mainly into three groups: predominantly coryneform bacteria (largely Arthrobacter), some Achromobacteraceae and a small groups of Pseudomonadaceae.

Molecular characterization of Prunus necrotic ringspot virus isolated from rose in Brazil

Directory of Open Access Journals (Sweden)

Thor Vinícius Martins Fajardo

2015-12-01

Full Text Available ABSTRACT: There is no molecular characterization of Brazilian isolates of Prunus necrotic ringspot virus (PNRSV, except for those infecting peach. In this research, the causal agent of rose mosaic was determined and the movement (MP and coat (CP protein genes of a PNRSV isolate from rose were molecularly characterized for the first time in Brazil. The nucleotide and deduced amino acid sequences of MP and CP complete genes were aligned and compared with other isolates. Molecular analysis of the MP and CP nucleotide sequences of a Brazilian PNRSV isolate from rose and others from this same host showed highest identities of 96.7% and 98.6%, respectively, and Rose-Br isolate was classified in PV32 group.

Complete genome sequence provides insights into the biodrying-related microbial function of Bacillus thermoamylovorans isolated from sewage sludge biodrying material.

Science.gov (United States)

Cai, Lu; Zheng, Sheng-Wei; Shen, Yu-Jun; Zheng, Guo-Di; Liu, Hong-Tao; Wu, Zhi-Ying

2018-07-01

To enable the development of microbial agents and identify suitable candidate used for biodrying, the existence and function of Bacillus thermoamylovorans during sewage sludge biodrying merits investigation. This study isolated a strain of B. thermoamylovorans during sludge biodrying, submitted it for complete genome sequencing and analyzed its potential microbial functions. After biodrying, the moisture content of the biodrying material decreased from 66.33% to 50.18%, and B. thermoamylovorans was the ecologically dominant Bacillus, with the primary annotations associated with amino acid transport and metabolism (9.53%) and carbohydrate transport and metabolism (8.14%). It contains 96 carbohydrate-active- enzyme-encoding gene counts, mainly distributed in glycoside hydrolases (33.3%) and glycosyl transferases (27.1%). The virulence factors are mainly associated with biosynthesis of capsule and polysaccharide capsule. This work indicates that among the biodrying microorganisms, B. thermoamylovorans has good potential for degrading recalcitrant and readily degradable components, thus being a potential microbial agent used to improve biodrying. Copyright © 2018 Elsevier Ltd. All rights reserved.

Molecular characterization of Cryptosporidium isolates from humans in Equatorial Guinea.

Science.gov (United States)

Blanco, María Alejandra; Iborra, Asunción; Vargas, Antonio; Nsie, Eugenia; Mbá, Luciano; Fuentes, Isabel

2009-12-01

The aim of the study was to perform a molecular characterization of clinical isolates of Cryptosporidium species from Equatorial Guinea. Standard laboratory methods were used to identify 35 cryptosporidiosis cases among 185 patients. PCR-RFLP successfully identified 34 Cryptosporidium species from these 35 cases, comprising C. parvum (52.9%), C. hominis (44.1%) and C. meleagridis (2.9%); over 90% of the species were isolated from HIV-positive patients. This is the first report of the molecular characterization of Cryptosporidium species isolated from humans in Equatorial Guinea and shows that zoonotic and anthroponotic transmission is present in this country.

Isolation, cloning and molecular characterization of a thermotolerant ...

African Journals Online (AJOL)

Isolation, cloning and molecular characterization of a thermotolerant xylanase from Streptomyces sp. THW31. Thayat Sriyapai, Peechapack Somyoonsap, Supatra Areekit, Paisarn Khawsak, Arda Pakpitcharoen, Kosum Chansiri ...

Investigation on ultrasonication mediated biosurfactant disintegration method in sludge flocs for enhancing hydrolytic enzymes activity and polyhydroxyalkanoates.

Science.gov (United States)

Sethupathy, A; Sivashanmugam, P

2018-06-04

In this study, a novel biosurfactant potential bacterial strain Pseudomonas pachastrellae RW43 was isolated from pulp and paper sludge and the biosurfactant namely rhamnolipid produced by Pseudomonas pachastrellae RW43 was investigated by varying pH and incubation time in batch liquid fermentation process. The maximal yield of rhamnolipid was found to be 12.1 g/L at an optimized condition of pH 7 and incubation time of 168 h. NMR analysis was performed for identification of molecular structure of produced rhamnolipid and its results concluded that the product was identified as di rhamnolipid. Then, statistically the global optimum conditions for hydrolytic enzymes extraction parameters (sonication power (100 W), extraction time (15 min) and rhamnolipid dosage (2% v/v)) were established. At 30,456 kJ/kg TS specific energy, ultrasonication with rhamnolipid disintegration method extracted maximal consortium activity of hydrolytic enzymes from mixed sludge (municipal and pulp & paper sludge) and the maximum observed were found to be 42.22, 51.75, 34.26, 24.21, 11.35 Units/g VSS respectively for protease, α-amylase, cellulase, lipase and α-glucosidase. Polyhydroxyalkanoates was recovered from enzymes extracted sludge using various solvents namely chloroform, sodium hypochlorite with chloroform and sodium lauryl sulfate with sodium hypochlorite. The maximum recovery was found to be 74 g/kg using sodium hypochlorite and chloroform extraction solvents.

Experience with a pilot plant for sewage sludge: Experiments on the inactivation of viruses in sewage sludge after a radiation treatment

International Nuclear Information System (INIS)

Epp, C.

1975-01-01

Investigations examining the virus inactivating effect of a Cobalt-60-plant were, till now, limited to the attempts to isolate virus from the sludge samples taken from sewage sludge before and after irradiation with 300 krad. As in those sludge samples virus presence could be proven only on a rather irregular basis, an experiment was devised in which defined virus quantities were packed into capsules and mixed with the digested sludge. At the end of the hygienization process these capsules were removed from the sludge and examined for virus content. Furthermore one radiation volume (5.6 m 3 ) was infected with attenuated polio virus type I and the virus content was determined before and after the radiation treatment. In 33 sludge samples examined before hygienization, presence of one or several viruses occurred in 8 samples. With the 33 capsules examined after hygienization with 300 krad, only 2 showed presence of virus. Suspensions of attenuated polio virus type I packed into synthetic capsules with a medium virus dosis of 10sup(6.92) JD 50/0.1 were immersed into sludge. In 6 experiments it was found that after hygienization, virus dosis was reduced to an average value of 10sup(5.4) JD 50/0.1 ml. Accordingly, the experimental results showed that after the radiation treatment the reduction of the exposed virus was more than 90%. Under natural conditions the investigation of the sewage sludge samples showed presence of virus 4 times less after hygienization than in the samples examined before hygienization. (orig./AK) [de

Bioleaching of heavy metals from sewage sludge using Acidithiobacillus thiooxidans

Science.gov (United States)

Wen, Ye-Ming; Lin, Hong-Yan; Wang, Qing-Ping; Chen, Zu-Liang

2010-11-01

Acidithiobacillus thiooxidans was isolated from sewage sludge using the incubation in the Waksman liquor medium and the inoculation in Waksman solid plate. It was found that the optimum conditions of the bioleaching included solid concentration 2%, sulfur concentration 5 gṡL-1 and cell concentration 10%. The removal efficiency of Cr, Cu, Pb and Zh in sewage sludge, which was obtained from waste treatment plant, Jinshan, Fuzhou, was 43.65%, 96.24%, 41.61% and 96.50% in the period of 4˜10 days under the optimum conditions, respectively. After processing using the proposed techniques, the heavy metals in sewage sludge did meet the requirement the standards of nation.

Molecular Characterization of Clostridium difficile Isolates in China From 2010 to 2015

Directory of Open Access Journals (Sweden)

Xiao-shu Liu

2018-04-01

Full Text Available Clostridium difficile infection (CDI has become a worldwide public health problem causing high mortality and a large disease burden. Molecular typing and analysis is important for surveillance and infection control of CDI. However, molecular characterization of C. difficile across China is extremely rare. Here, we report on the toxin profiles, molecular subtyping with multilocus sequence typing (MLST and PCR ribotyping, and epidemiological characteristics of 199 C. difficile isolates collected between 2010 through 2015 from 13 participating centers across China. We identified 35 STs and 27 ribotypes (RTs among the 199 C. difficile isolates: ST35 (15.58%, ST3 (15.08%, ST37 (12.06%, and RT017 (14.07%, RT001 (12.06%, RT012 (11.56% are the most prevalent. One isolate with ST1 and 8 isolates with ST 11 were identified. We identified a new ST in this study, denoted ST332. The toxin profile tcdA+tcdB+tcdC+tcdR+tcdE+CDT- (65.83% was the predominant profile. Furthermore, 11 isolates with positive binary toxin genes were discovered. According to the PCR ribotyping, one isolate with RT 027, and 6 isolates with RT 078 were confirmed. The epidemiological characteristics of C. difficile in China shows geographical differences, and both the toxin profile and molecular types exhibit great diversity across the different areas.

Co-conditioning and dewatering of chemical sludge and waste activated sludge.

Science.gov (United States)

Chang, G R; Liu, J C; Lee, D J

2001-03-01

The conditioning and dewatering behaviors of chemical and waste activated sludges from a tannery were studied. Capillary suction time (CST), specific resistance to filtration (SRF), and bound water content were used to evaluate the sludge dewatering behaviors. Zeta potentials were also measured. Experiments were conducted on each sludge conditioned and dewatered separately, and on the sludge mixed at various ratios. Results indicate that the chemical sludge was relatively difficult to be dewatered, even in the presence of polyelectrolyte. When the waste activated sludge was mixed with the chemical sludge at ratios of 1:1 and 2:1, respectively, the dewaterability of chemical sludge improved remarkably while the relatively better dewaterability of the waste activated sludge deteriorated only to a limited extent. As the mixing ratios became 4:1 and 8:1, the dewaterability of the mixed sludge was equal to that of the waste activated sludge. The optimal polyelectrolyte dosage for the mixed sludge was equal to or less than that of the waste activated sludge. It is proposed that the chemical sludges act as skeleton builders that reduce the compressibility of the mixed sludge whose dewaterability is enhanced. Bound water contents of sludge decreased at low polyelectrolyte dosage and were not significantly affected as polyelectrolyte dosage increased. Advantages and disadvantages of co-conditioning and dewatering chemical sludge and waste activated sludge were discussed.

Minimization of Excess Sludge in Activated Sludge Systems

Directory of Open Access Journals (Sweden)

Sayed Ali Reza Momeni

2006-01-01

Full Text Available The disposal of excess sludge from wastewater treatment plant represents a rising challenge in activated sludge processes. Hence, the minimization of excess sludge production was investigated by increasing the dissolved oxygen in aeration basin. Units of the pilot include: Primary sedimentation tank, aeration basin, secondary sedimentation tank, and return sludge tank. Volume of aeration basin is 360 l and influent flow rate is 90 L/h. Influent of pilot is taken from effluent of grit chamber of Isfahan's North Wastewater treatment plant. The experiments were done on different parts of pilot during the 5 month of study. Results show that increase of dissolved oxygen in aeration tank affect on decrease of excess sludge. Increase of dissolved oxygen from 0.5 to 4.5 mg/L resulted in 25% decrease of excess sludge. Variation of dissolved oxygen affect on settleability of sludge too. By increase of dissolved oxygen, SVI decreased and then increased. Value of 1-3 mg/L was the adequate range of dissolved oxygen by settleability of sludge and optimum range was 2-2.5 mg/L. It could be concluded by increasing of dissolved oxygen up to of 3 mg/L, sludge settleability significant decreased.

Rate of biodegradation of crude oil by microorganisms isolated from ...

African Journals Online (AJOL)

The rate of biodegradation of crude oil by micro-organisms isolated from crude oil sludge environment in Eket, Akwa Ibom State of Nigeria was studied. Mineral salt medium supplemented with crude oil was used and three most abundant species isolated from a crude oil sludged soil - Micrococcus varians, Bacillus subtilis ...

Enhanced composting of radiation disinfected sewage sludge

International Nuclear Information System (INIS)

Kawakami, W.; Hashimoto, S.

1984-01-01

Studies on isothermal composting of radiation disinfected sewage sludge and liquid chromatography of water extracts of the products were carried out. The optimum temperature and pH were around 50 deg C and 7 to 8, respectively. The repeated use of products as seeds increased the rate of CO 2 evolution. The rate reached a maximum within 10 hours and decreased rapidly, and the CO 2 evolution ceased after about 3 days. The conversion of organic carbon to carbon dioxide attained to about 40% for the repeated use of products as seeds at the optimum conditions. As long as seeds as available were used, no remarkable difference was found in the composting of unirradiated and irradiated sludges. The composting process using radiation, however, can be carried out at the optimum conditions and is expected to shorten the composting period, because it is not necessary to keep fermentation temperature higher to reduce pathogen in sludge. Liquid chromatographic studies of the products showed that low molecular components decreased and higher molecular ones increased with fermentation. An index expressing the degree of reduction of easily decomposable organics was presented. The index also showed that the optimum temperature for fermentation was 50 deg C. (author)

Ultrasonic reduction of excess sludge from the activated sludge system

International Nuclear Information System (INIS)

Zhang Guangming; Zhang Panyue; Yang Jinmei; Chen Yanming

2007-01-01

Sludge treatment has long become the most challenging problem in wastewater treatment plants. Previous studies showed that ozone or chlorine effectively liquefies sludge into substrates for bio-degradation in the aeration tank, and thus reduces the excess sludge. This paper employs ultrasound to reduce the excess sludge from the sequential batch reactor (SBR) system. Partial sludge was disintegrated into dissolved substrates by ultrasound in an external sono-tank and was then returned to the SBR for bio-degradation. The results showed that ultrasound (25 kHz) effectively liquefied the sludge. The most effective conditions for sludge reduction were as following: sludge sonication ratio of 3/14, ultrasound intensity of 120 kW/kgDS, and sonication duration of 15 min. The amount of excess sludge was reduced by 91.1% to 17.8 mg/(L d); the organic content and settleability of sludge in the SBR were not impacted. The chemical oxygen demand (COD) removal efficiency was 81.1%, the total nitrogen (TN) removal efficiency was 17-66%, and high phosphorus concentration in the effluent was observed

Heating value characteristics of sewage sludge: a comparative study of different sludge types

International Nuclear Information System (INIS)

Kim, Young-JU.; Kang, Hae-Ok.; Qureshi, T.I.

2005-01-01

Heating value characteristics of three different types of sludge, i.e. domestic sewage sludge, industrial sludge, and industrial + domestic sewage sludge were investigated. Industrial + domestic sewage sludge (thickened) showed the highest heating value (5040 kcal/kg) than other sludge types. This may be due to increased amount of organic matter presents in thickened sludge than de-watered sludge. A gradual increase in organic matter of the sludge was observed with the increase of the moisture contents. Heating value of the sludge having 60% moisture contents was found in the range between 924-1656 kcal/kg and this amount was higher than the minimum heating value (800 kcal/kg) required sustaining auto thermal combustion in sludge incineration process. Energy consumption requirement for pre drying sludge operations revealed that industrial sludge (de-watered) required the minimum cost (13 $/ton of sludge) to make it a sludge of fuel grade (60% W), while mixed sludge cost the highest amount for its pre-drying operations. (author)

Comparison of extended-spectrum-β-lactamase (ESBL) carrying Escherichia coli from sewage sludge and human urinary tract infection

International Nuclear Information System (INIS)

Zarfel, G.; Galler, H.; Feierl, G.; Haas, D.; Kittinger, C.; Leitner, E.; Grisold, A.J.; Mascher, F.; Posch, J.; Pertschy, B.; Marth, E.; Reinthaler, F.F.

2013-01-01

For many years, extended-spectrum-beta-lactamase (ESBL) producing bacteria were a problem mainly located in medical facilities. Within the last decade however, ESBL-producing bacteria have started spreading into the community and the environment. In this study, ESBL-producing Escherichia coli from sewage sludge were collected, analysed and compared to ESBL-E. coli from human urinary tract infections (UTIs). The dominant ESBL-gene-family in both sample groups was bla CTX-M , which is the most prevalent ESBL-gene-family in human infection. Still, the distribution of ESBL genes and the frequency of additional antibiotic resistances differed in the two sample sets. Nevertheless, phenotyping did not divide isolates of the two sources into separate groups, suggesting similar strains in both sample sets. We speculate that an exchange is taking place between the ESBL E. coli populations in infected humans and sewage sludge, most likely by the entry of ESBL E. coli from UTIs into the sewage system. - Highlights: ► ESBL E. coli strains from sewage sludge harbour the same dominant ESBL enzymes as human isolates. ► High resistance rates for important antibiotics can be found in isolated ESBL strains. ► High phenotypic diversity of ESBL E. coli isolates from sewage sludge and from human sources. - The distribution of ESBL resistance genes in isolates from patients and environmental samples.

Gamma radiation inactivation of pathogens in sludge under larger-scale condition

Energy Technology Data Exchange (ETDEWEB)

Sermkiattipong, N; Pongpat, S

1996-12-01

The effect of gamma radiation on microorganisms in sludge from Huay Kwang Sewage Treatment Plant and Vajira Hospital showed that total bacterial counts were reduced to 2-3 log cycles and 1-2 log cycles at 5 kGy irradiation with and without aeration, respectively. Inactivation of coliform bacteria in sludge required irradiation with and without aeration at the dosages of 3-4.5 and 4-5 kGy, respectively. A dose of 2-3 kGy was sufficient to inactivate fecal coliform bacteria and E. coli. The doses used for inactivation these bacteria depend on the irradiation condition and solid content in sludge sample. Irradiation with aeration led to an increased microbial inactivation. According to our results, the frequency of occurrence of salmonella e contaminated in sludge from Huay Kwang Sewage Treatment Plant and Vajira Hospital was 50% and 75%, respectively. A dose of 2 kGy irradiation with or without aeration, salmonella e could not be detected in any sludge. Clostridium perfringens organisms were also detected in non-irradiated and irradiated sludge from both sources. Moreover, a dose of 5 kGy irradiation with or without aeration was not enough to eliminate C. perfringens. However, no shigella e were isolated from any treatment of sludge

Gamma radiation inactivation of pathogens in sludge under larger-scale condition

International Nuclear Information System (INIS)

Sermkiattipong, N.; Pongpat, S.

1996-01-01

The effect of gamma radiation on microorganisms in sludge from Huay Kwang Sewage Treatment Plant and Vajira Hospital showed that total bacterial counts were reduced to 2-3 log cycles and 1-2 log cycles at 5 kGy irradiation with and without aeration, respectively. Inactivation of coliform bacteria in sludge required irradiation with and without aeration at the dosages of 3-4.5 and 4-5 kGy, respectively. A dose of 2-3 kGy was sufficient to inactivate fecal coliform bacteria and E. coli. The doses used for inactivation these bacteria depend on the irradiation condition and solid content in sludge sample. Irradiation with aeration led to an increased microbial inactivation. According to our results, the frequency of occurrence of salmonella e contaminated in sludge from Huay Kwang Sewage Treatment Plant and Vajira Hospital was 50% and 75%, respectively. A dose of 2 kGy irradiation with or without aeration, salmonella e could not be detected in any sludge. Clostridium perfringens organisms were also detected in non-irradiated and irradiated sludge from both sources. Moreover, a dose of 5 kGy irradiation with or without aeration was not enough to eliminate C. perfringens. However, no shigella e were isolated from any treatment of sludge

Use of a water treatment sludge in a sewage sludge dewatering process

Science.gov (United States)

Górka, Justyna; Cimochowicz-Rybicka, Małgorzata; Kryłów, Małgorzata

2018-02-01

The objective of the research study was to determine whether a sewage sludge conditioning had any impact on sludge dewaterability. As a conditioning agent a water treatment sludge was used, which was mixed with a sewage sludge before a digestion process. The capillary suction time (CST) and the specific filtration resistance (SRF) were the measures used to determine the effects of a water sludge addition on a dewatering process. Based on the CST curves the water sludge dose of 0.3 g total volatile solids (TVS) per 1.0 g TVS of a sewage sludge was selected. Once the water treatment sludge dose was accepted, disintegration of the water treatment sludge was performed and its dewaterability was determined. The studies have shown that sludge dewaterability was much better after its conditioning with a water sludge as well as after disintegration and conditioning, if comparing to sludge with no conditioning. Nevertheless, these findings are of preliminary nature and future studies will be needed to investigate this topic.

Isolation and molecular characterization of phytase producing ...

African Journals Online (AJOL)

Isolation and molecular characterization of phytase producing bacteria from Malaysia hot springs. ... The strains were further analyzed in broth culture using sodium phytate as substrate. Among them, strain L3 was selected as the best producer (0.16 U/ml after 72 h of culture). This phytase showed optimal activity at 37 °C ...

Metabolic and Co-Metabolic Transformation of Diclofenac by Enterobacter hormaechei D15 Isolated from Activated Sludge.

Science.gov (United States)

Aissaoui, Salima; Ouled-Haddar, Houria; Sifour, Mohamed; Harrouche, Kamel; Sghaier, Haitham

2017-03-01

The presence of non-steroidal anti-inflammatory drugs, such as diclofenac (DCF), in the environment, is an emerging problem due to their harmful effects on non-target organisms, even at low concentrations. We studied the biodegradation of DCF by the strain D15 of Enterobacter hormaechei. The strain was isolated from an activated sludge, and identified as E. hormaechei based on its physiological characteristics and its 16 S RNA sequence. Using HPTLC and GC-MS methods, we demonstrated that this strain metabolized DCF at an elimination rate of 52.8%. In the presence of an external carbon source (glucose), the elimination rate increased to approximately 82%. GC-MS analysis detected and identified one metabolite as 1-(2,6-dichlorophenyl)-1,3-dihydro-2H-indol-2-one; it was produced as a consequence of dehydration and lactam formation reactions.

Molecular characterization of Salmonella isolates by REP-PCR and RAPD analysis.

Science.gov (United States)

Albufera, U; Bhugaloo-Vial, P; Issack, M I; Jaufeerally-Fakim, Y

2009-05-01

Eighteen Salmonella isolates from both human and food (non-human) sources (fish, meat, and poultry) were characterized using conventional culture methods, biochemical, serological, and molecular analyses. REP-PCR and RAPD produced DNA profiles for differentiation purposes. Enterobacterial repetitive intergenic consensus (ERIC), repetitive extragenic palindronic (REP) and BOXAIR primers were selected for REP-PCR and two arbitrary primers, namely OPP-16 and OPS-11 were used for RAPD to generate DNA fingerprints from the Salmonella isolates. REP-PCR method showed greater discriminatory power in differentiating closely related strains of the related strains of Salmonella and produced more complex banding patterns as compared with RAPD. A dendogram was constructed with both sets of profiles using SPSS Version 13.0 computer software and showed that most human isolates were separately clustered from the non-human isolates. Two of the human isolates were closely related to some of the non-human isolates. A good correlation was also observed between the serogrouping of the O antigen and the molecular profiles obtained from REP-PCR and RAPD data of the Salmonella isolates. The results of a principal coordinate analysis (PCA) corresponded to the clustering in the dendrogram.

Economic comparison of sludge irradiation and alternative methods of municipal sludge treatment

International Nuclear Information System (INIS)

Ahlstrom, S.B.; McGuire, H.E.

1977-11-01

The relative economics of radiation treatment and other sludge treatment processes are reported. The desirability of radiation treatment is assessed in terms of cost and the quality of the treated sludge product. The major conclusions of this study are: radiation treatment is a high-level disinfection process. Therefore, it should only be considered if high levels of disinfection are required for widespread reuse of the sludge; the handling, transporting and pathogen growback problems associated with disinfected wet sludge makes it less attractive for reuse than dry sludge; radiation of composted sludge produces a product of similar quality at less cost than any thermal treatment and/or flash drying treatment option for situations where a high degree of disinfection is required; and heavy metal concerns, especially cadmium, may limit the reuse of sludge despite high disinfection levels. It is recommended that radiation treatment of sludge, particularly dry sludge, continue to be studied. A sensitivity analysis investigating the optimal conditions under which sludge irradiation operates should be instigated. Furthermore, costs of adding sludge irradiation to existing sludge treatment schemes should be determined

In Situ Detection, Isolation, and Physiological Properties of a Thin Filamentous Microorganism Abundant in Methanogenic Granular Sludges: a Novel Isolate Affiliated with a Clone Cluster, the Green Non-Sulfur Bacteria, Subdivision I

OpenAIRE

Sekiguchi, Yuji; Takahashi, Hiroki; Kamagata, Yoichi; Ohashi, Akiyoshi; Harada, Hideki

2001-01-01

We previously showed that very thin filamentous bacteria affiliated with the division green non-sulfur bacteria were abundant in the outermost layer of thermophilic methanogenic sludge granules fed with sucrose and several low-molecular-weight fatty acids (Y. Sekiguchi, Y. Kamagata, K. Nakamura, A. Ohashi, H. Harada, Appl. Environ. Microbiol. 65:1280–1288, 1999). Further 16S ribosomal DNA (rDNA) cloning-based analysis revealed that the microbes were classified within a unique clade, green non...

Biological sludge solubilisation for reduction of excess sludge production in wastewater treatment process.

Science.gov (United States)

Yamaguchi, T; Yao, Y; Kihara, Y

2006-01-01

A novel sludge disintegration system (JFE-SD system) was developed for the reduction of excess sludge production in wastewater treatment plants. Chemical and biological treatments were applied to disintegrate excess sludge. At the first step, to enhance biological disintegration, the sludge was pretreated with alkali. At the second step, the sludge was disintegrated by biological treatment. Many kinds of sludge degrading microorganisms integrated the sludge. The efficiency of the new sludge disintegration system was confirmed in a full-scale experiment. The JFE-SD system reduced excess sludge production by approximately 50% during the experimental period. The quality of effluent was kept at quite a good level. Economic analysis revealed that this system could significantly decrease the excess sludge treatment cost.

Enhancing sludge biodegradability and volatile fatty acid production by tetrakis hydroxymethyl phosphonium sulfate pretreatment.

Science.gov (United States)

Wu, Qing-Lian; Guo, Wan-Qian; Bao, Xian; Yin, Ren-Li; Feng, Xiao-Chi; Zheng, He-Shan; Luo, Hai-Chao; Ren, Nan-Qi

2017-09-01

A new pretreatment method based on tetrakis hydroxymethyl phosphonium sulfate (THPS) biocide was tried to enhance sludge disintegration, and improved sludge biodegradability and subsequent volatile fatty acid (VFA) production. Sludge activity decreased to less than 10% after 2 days pretreatment using 20mg/g-TSS THPS, which also obviously destroyed EPS and cell membrane, and dissolved more biodegradable substances (48.8%) than raw sludge (19.7%). Moreover, 20mg/g-TSS THPS pretreatment shortened fermentation time to 4days and improved VFA production to 2778mg COD/L (4.35 times than that in control). Therein, the sum of n-butyric, n-valeric and iso-valeric acids unexpectedly accounted for 60.5% of total VFA (only 20.1% of that in control). The more high molecular weight VFAs (C4-C5) than low molecular VFAs (C2-C3) resulted from THPS pretreatment benefited to subsequent medium-chain volatile acids (C6-C12) generation to realize the separation and recovery of organic carbon more efficiently. Copyright © 2017. Published by Elsevier Ltd.

Strength Measurements of Archive K Basin Sludge Using a Soil Penetrometer

International Nuclear Information System (INIS)

Delegard, Calvin H.; Schmidt, Andrew J.; Chenault, Jeffrey W.

2011-01-01

Spent fuel radioactive sludge present in the K East and K West spent nuclear fuel storage basins now resides in the KW Basin in six large underwater engineered containers. The sludge will be dispositioned in two phases under the Sludge Treatment Project: (1) hydraulic retrieval into sludge transport and storage containers (STSCs) and transport to interim storage in Central Plateau and (2) retrieval from the STSCs, treatment, and packaging for shipment to the Waste Isolation Pilot Plant. In the years the STSCs are stored, sludge strength is expected to increase through chemical reaction, intergrowth of sludge crystals, and compaction and dewatering by settling. Increased sludge strength can impact the type and operation of the retrieval equipment needed prior to final sludge treatment and packaging. It is important to determine whether water jetting, planned for sludge retrieval from STSCs, will be effective. Shear strength is a property known to correlate with the effectiveness of water jetting. Accordingly, the unconfined compressive strengths (UCS) of archive K Basin sludge samples and sludge blends were measured using a pocket penetrometer modified for hot cell use. Based on known correlations, UCS values can be converted to shear strengths. Twenty-six sludge samples, stored in hot cells for a number of years since last being disturbed, were identified as potential candidates for UCS measurement and valid UCS measurements were made for twelve, each of which was found as moist or water-immersed solids at least 1/2-inch deep. Ten of the twelve samples were relatively weak, having consistencies described as 'very soft' to 'soft'. Two of the twelve samples, KE Pit and KC-4 P250, were strong with 'very stiff' and 'stiff' consistencies described, respectively, as 'can be indented by a thumb nail' or 'can be indented by thumb'. Both of these sludge samples are composites collected from KE Basin floor and Weasel Pit locations. Despite both strong sludges having

Strength Measurements of Archive K Basin Sludge Using a Soil Penetrometer

Energy Technology Data Exchange (ETDEWEB)

Delegard, Calvin H.; Schmidt, Andrew J.; Chenault, Jeffrey W.

2011-12-06

Spent fuel radioactive sludge present in the K East and K West spent nuclear fuel storage basins now resides in the KW Basin in six large underwater engineered containers. The sludge will be dispositioned in two phases under the Sludge Treatment Project: (1) hydraulic retrieval into sludge transport and storage containers (STSCs) and transport to interim storage in Central Plateau and (2) retrieval from the STSCs, treatment, and packaging for shipment to the Waste Isolation Pilot Plant. In the years the STSCs are stored, sludge strength is expected to increase through chemical reaction, intergrowth of sludge crystals, and compaction and dewatering by settling. Increased sludge strength can impact the type and operation of the retrieval equipment needed prior to final sludge treatment and packaging. It is important to determine whether water jetting, planned for sludge retrieval from STSCs, will be effective. Shear strength is a property known to correlate with the effectiveness of water jetting. Accordingly, the unconfined compressive strengths (UCS) of archive K Basin sludge samples and sludge blends were measured using a pocket penetrometer modified for hot cell use. Based on known correlations, UCS values can be converted to shear strengths. Twenty-six sludge samples, stored in hot cells for a number of years since last being disturbed, were identified as potential candidates for UCS measurement and valid UCS measurements were made for twelve, each of which was found as moist or water-immersed solids at least 1/2-inch deep. Ten of the twelve samples were relatively weak, having consistencies described as 'very soft' to 'soft'. Two of the twelve samples, KE Pit and KC-4 P250, were strong with 'very stiff' and 'stiff' consistencies described, respectively, as 'can be indented by a thumb nail' or 'can be indented by thumb'. Both of these sludge samples are composites collected from KE Basin floor and

Molecular variability among isolates of Fusarium oxysporum associated with root rot disease of Agave tequilana.

Science.gov (United States)

Vega-Ramos, Karla L; Uvalle-Bueno, J Xavier; Gómez-Leyva, Juan F

2013-04-01

In this study, 115 isolates of Fusarium oxysporum from roots of Agave tequilana Weber cv azul plants and soil in commercial plantations in western Mexico were characterized using morphological and molecular methods. Genetic analyses of monosporic isolates included restriction enzyme analysis of rDNA (ARDRA) using HaeIII and HinfI, and genetic diversity was determined using Box-PCR molecular markers. Box-PCR analysis generated 14 groups. The groups correlated highly with the geographic location of the isolate and sample type. These results demonstrate the usefulness of ARDRA and Box-PCR techniques in the molecular characterization of the Fusarium genus for the discrimination of pathogenic isolates.

An Economic comparison of sludge irradiation and alternative methods of municipal sludge treatment

Energy Technology Data Exchange (ETDEWEB)

Ahlstrom, S.B.; McGuire, H.E.

1977-11-01

The relative economics of radiation treatment and other sludge treatment processes are reported. The desirability of radiation treatment is assessed in terms of cost and the quality of the treated sludge product. The major conclusions of this study are: radiation treatment is a high-level disinfection process. Therefore, it should only be considered if high levels of disinfection are required for widespread reuse of the sludge; the handling, transporting and pathogen growback problems associated with disinfected wet sludge makes it less attractive for reuse than dry sludge; radiation of composted sludge produces a product of similar quality at less cost than any thermal treatment and/or flash drying treatment option for situations where a high degree of disinfection is required; and heavy metal concerns, especially cadmium, may limit the reuse of sludge despite high disinfection levels. It is recommended that radiation treatment of sludge, particularly dry sludge, continue to be studied. A sensitivity analysis investigating the optimal conditions under which sludge irradiation operates should be instigated. Furthermore, costs of adding sludge irradiation to existing sludge treatment schemes should be determined.

Sewage sludge disintegration by high-pressure homogenization: a sludge disintegration model.

Science.gov (United States)

Zhang, Yuxuan; Zhang, Panyue; Ma, Boqiang; Wu, Hao; Zhang, Sheng; Xu, Xin

2012-01-01

High-pressure homogenization (HPH) technology was applied as a pretreatment to disintegrate sewage sludge. The effects of homogenization pressure, homogenization cycle number, and total solid content on sludge disintegration were investigated. The sludge disintegration degree (DD(COD)), protein concentration, and polysaccharide concentration increased with the increase of homogenization pressure and homogenization cycle number, and decreased with the increase of sludge total solid (TS) content. The maximum DD(COD) of 43.94% was achieved at 80 MPa with four homogenization cycles for a 9.58 g/L TS sludge sample. A HPH sludge disintegration model of DD(COD) = kNaPb was established by multivariable linear regression to quantify the effects of homogenization parameters. The homogenization cycle exponent a and homogenization pressure exponent b were 0.4763 and 0.7324 respectively, showing that the effect of homogenization pressure (P) was more significant than that of homogenization cycle number (N). The value of the rate constant k decreased with the increase of sludge total solid content. The specific energy consumption increased with the increment of sludge disintegration efficiency. Lower specific energy consumption was required for higher total solid content sludge.

Radiation disinfection of sewage sludge and composting of the irradiated sludge

International Nuclear Information System (INIS)

Hashimoto, Shoji; Nishimura, Koichi; Watanabe, Hiromasa; Kawakami, Waichiro

1985-01-01

In the radiation disinfected sewage sludge, its stabilization is necessary with the composting. In this disinfected sludge, there is no need of keeping it at high temperature at the cost of fermentation velocity. The fermentation velocity can thus be set to obtain its maximum value. In sewage sludge utilization of farm land, to prevent the contamination with pathogenic bacteria and the secondary pollution, the radiation disinfection of dehydrated sludge and the composting of the disinfected sludge have been studied. The disinfection effect when an electron accelerator is used for the radiation source is described. Then, the composting of the disinfected sludge is described in chemical kinetics of the microorganisms. (Mori, K.)

First isolation and molecular characterization of Ehrlichia canis in Costa Rica, Central America.

Science.gov (United States)

Romero, L E; Meneses, A I; Salazar, L; Jiménez, M; Romero, J J; Aguiar, D M; Labruna, M B; Dolz, G

2011-08-01

The present study investigated Ehrlichia species in blood samples from dogs suspected of clinical ehrlichiosis, using molecular and isolation techniques in cell culture. From a total of 310 canine blood samples analyzed by 16S rRNA nested PCR, 148 (47.7%) were positive for Ehrlichia canis. DNA from Ehrlichia chaffeensis or Ehrlichia ewingii was not detected in any sample using species-specific primers in separated reactions. Leukocytes from five PCR-positive dogs were inoculated into DH82 cells; successful isolation of E. canis was obtained in four samples. Partial sequence of the dsb gene of eight canine blood samples (including the five samples for in vitro isolation) was obtained by PCR and their analyses through BLAST showed 100% of identity with the corresponding sequence of E. canis in GenBank. This study represents the first molecular diagnosis, isolation, and molecular characterization of E. canis in dogs from Costa Rica. Copyright © 2010 Elsevier Ltd. All rights reserved.

Sludge derived fuel technique of sewage sludge by oil vacuum evaporation drying

International Nuclear Information System (INIS)

Kim, Seokhwan; Lim, Byungran; Lee, Sookoo

2010-01-01

Sewage sludge contains high content of organic materials and its water content is also very high about 80% even after filtration process. Landfill as a sludge treatment methods can cause odor problem and leachate production which can derive the secondary contamination of soil and groundwater. The ocean dumping will be prohibited according to the London Convention and domestic stringent environmental regulation. Based on domestic agenda on organic sewage sludge treatment, the ocean disposal will be prohibited from 2012, thus alternative methods are demanded. Sludge derived fuel (SDF) technology can alleviate the emission of greenhouse gas and recover energy from sludge. For proper treatment and SDF production from sludge, the vacuum evaporation and immersion frying technology was adopted in this research. This technology dries moisture in sludge after mixing with oil such as Bunker C oil, waste oil or waste food oil etc. Mixing sludge and oil secures liquidity of organic sludge to facilitate handling throughout the drying process. The boiling temperature could be maintained low through vacuum condition in whole evaporation process. This study was performed to find the optimum operating temperature and pressure, the mixing ratio of sludge and oil. Finally, we could obtained SDF which moisture content was less than 5%, its heating value was over 4,500 kcal/ kg sludge. This heating value could satisfy the Korean Fuel Standard for the Recycle Products. Assessed from the perspective of energy balance and economic evaluation, this sludge drying system could be widely used for the effective sludge treatment and the production of SDF. (author)

Sludge recovery apparatus

International Nuclear Information System (INIS)

Marmo, A.R.

1979-01-01

Sludge recovery machine comprising a hollow centrifuge, a vertical pipe for feeding in a liquid containing sludge and a sliding rake pressing against the internal wall of the centrifuge to dislodge and move the sludge, a power drive for spinning the centrifuge at high speed and a rotating drying table to take the sludge and dry it [fr

Excess sludge reduction in activated sludge processes by integrating ultrasound treatment

International Nuclear Information System (INIS)

Perez-Elvira, S.; Fdz-Polanco, M.; Plaza, F. I.; Garralon, G.; Fdz-Polanco, F.

2009-01-01

Biological sludge produced in the activated sludge process can be minimised modifying the water line, the sludge line or the final disposal strategy. Selecting the water line the general idea is to reduce the sludge producing the yield coefficient by means of the called lysis cryptic growth process. The main techniques referenced in literature are onization, chlorination and chemical and heat treatment. Ultrasounds are widely used to increase anaerobic biodegradability but are not reported as system to control excess sludge production. (Author)

Inactivation of Clostridium difficile in sewage sludge by anaerobic thermophilic digestion.

Science.gov (United States)

Xu, Changyun; Salsali, Hamidreza; Weese, Scott; Warriner, Keith

2016-01-01

There has been an increase in community-associated Clostridium difficile infections with biosolids derived from wastewater treatment being identified as one potential source. The current study evaluated the efficacy of thermophilic digestion in decreasing levels of C. difficile ribotype 078 associated with sewage sludge. Five isolates of C. difficile 078 were introduced (final density of 5 log CFU/g) into digested sludge and subjected to anaerobic digestion at mesophilic (36 or 42 °C) or thermophilic (55 °C) temperatures for up to 60 days. It was found that mesophilic digestion at 36 °C did not result in a significant reduction in C. difficile spore levels. In contrast, thermophilic sludge digestion reduced endospore levels at a rate of 0.19-2.68 log CFU/day, depending on the strain tested. The mechanism of lethality was indirect - by stimulating germination then inactivating the resultant vegetative cells. Acidification of sludge by adding acetic acid (6 g/L) inhibited the germination of spores regardless of the sludge digestion temperature. In conclusion, thermophilic digestion can be applied to reduce C. difficile in biosolids, thereby reducing the environmental burden of the enteric pathogen.

Measurements and thermodynamics of hydrotreater product sludge stability

Energy Technology Data Exchange (ETDEWEB)

Andersen, S.I. [Technical Univ. of Denmark, Lyngby (Denmark)

2003-07-01

Sludge is a by-product of the hydrotreating process of asphaltene during feedstock conversions. The stability of the asphaltenes in the system is related to the produced sludge. The remaining asphaltenes are unstable due to chemical changes in the mixture even though a large conversion of heptane asphaltene occurs. The flocculation titration technique was applied to several feedstocks and catalysts to understand changes in stability and to develop conversion schemes that avoid sludge formation. The effect of temperature conversion was studied in detail. Results obtained by flocculation titration were in agreement with size exclusion chromatography, elemental analysis, infrared spectroscopy and other methods. The authors also examined the chemical changes in product and in product asphaltenes. It was concluded that high hydrotreatment temperature leads to the formation of unstable products as cracking occurs. It was shown that molecular weight of asphaltenes decreases during the hydroprocessing, and the transition temperature is related to the feed. tabs., figs.

Effects of different sludge disintegration methods on sludge moisture distribution and dewatering performance.

Science.gov (United States)

Jin, Lingyun; Zhang, Guangming; Zheng, Xiang

2015-02-01

A key step in sludge treatment is sludge dewatering. However, activated sludge is generally very difficult to be dewatered. Sludge dewatering performance is largely affected by the sludge moisture distribution. Sludge disintegration can destroy the sludge structure and cell wall, so as change the sludge floc structure and moisture distribution, thus affecting the dewatering performance of sludge. In this article, the disintegration methods were ultrasound treatment, K2FeO4 oxidation and KMnO4 oxidation. The degree of disintegration (DDCOD), sludge moisture distribution and the final water content of sludge cake after centrifuging were measured. Results showed that three disintegration methods were all effective, and K2FeO4 oxidation was more efficient than KMnO4 oxidation. The content of free water increased obviously with K2FeO4 and KMnO4 oxidations, while it decreased with ultrasound treatment. The changes of free water and interstitial water were in the opposite trend. The content of bounding water decreased with K2FeO4 oxidation, and increased slightly with KMnO4 oxidation, while it increased obviously with ultrasound treatment. The water content of sludge cake after centrifuging decreased with K2FeO4 oxidation, and did not changed with KMnO4 oxidation, but increased obviously with ultrasound treatment. In summary, ultrasound treatment deteriorated the sludge dewaterability, while K2FeO4 and KMnO4 oxidation improved the sludge dewaterability. Copyright © 2014. Published by Elsevier B.V.

Sludge disintegration techniques - assessment of their impacts on solubilization of organic carbon and methane production

OpenAIRE

Fatoorehchi, Elham

2016-01-01

In the present thesis, ozone, sodium hydroxide and ultrasound were conducted to disintegrate the excess sludge prior to anaerobic digestion with the aim of improving methane production. The impacts of different sludge disintegration methods on the molecular size distribution of DOC solubilized after disintegration were investigated using size exclusion chromatography with online organic carbon detection (SEC-OCD).

Bioprocessing of sewage sludge for safe recycling on agricultural land - BIOWASTE

Energy Technology Data Exchange (ETDEWEB)

Schmidt, Jens Ejbye; Angelidaki, Irini; Christensen, Nina; Batstone, Damien John; Lyberatos, Gerasimos; Stamatelatou, Katerina; Lichtfouse, Eric; Elbisser, Brigitte; Rogers, Kayne; Sappin-Didier, Valerie; Dernaix, Laurence; Caria; Giovanni; Metzger, Laure; Borghi, Veronica; Montcada, Eloi

2003-07-01

Disposal and handling of sewage sludge are increasing problems in Europe due to the increasing quantities of the sewage sludge produced. A large amount of the sewage sludge contains small fractions of toxic chemicals, which results in problems with safe use of the sewage sludge on agricultural land. From an ecological and economical point of view, it would be essential to establish methodologies, which could allow sewage sludge to be reused as fertilizers on agricultural land. Energy efficient biotreatment processes of organic waste are, therefore, of crucial importance. BIOWASTE will offer an integrated study of this area. The typical composition of sewage sludge will be characterized with regard to key contaminating compounds. The following compounds will be in focus: Emulsifying agents such as nonylphenols and nonylphenol ethoxylates (NPE), polycyclic aromatic hydrocarbons (PAHs) derived from incomplete combustion processes and phthalates, which are used as additives in plastics and surfactants such as linear alkyl benzene sulfonate (LAS). Analytical techniques suitable for qualitative and quantitative evaluation of the chemical species involved in the processes under investigation will be determined. Bacteria that are able to degrade selected contaminating compounds under anaerobic and aerobic conditions will be isolated, characterized and bioaugmented for decontamination of sewage sludge through bioprocessing. Aerobic, anaerobic and combination of aerobic/anaerobic bioprocessing of sewage sludge will be applied. A mathematical model will be developed to describe the biodegradation processes of the contaminating compounds after establishing the kinetic parameters for degradation of contaminating compounds. The bioprocessed sewage sludge will be used in eco- and plant- toxicology tests to evaluate the impact of the xenobiotics on the environment. Methodologies will be developed and applied to assess the cleanliness of the bioprocessing as a safe method for waste

Molecular Typing of Salmonella Isolates in Poultry by Pulsed-Field Gel Electrophoresis in Iran

Directory of Open Access Journals (Sweden)

Narges Golab

2014-11-01

Full Text Available Background: Salmonella is one of the most widespread zoonotic enter pathogenic microorganisms found in the global food chain. Poultryand Poultry products have been identified as one of the important foodborne sources of Salmonella. Pulsed-Field Gel Electrophoresis (PFGE is a gold standard typing method for identification of Salmonella isolates during outbreaks and epidemiological investigations. Objectives: The aim of this study was to carry out molecular typing of Salmonella enterica spp. by PFGE technique. Materials and Methods: All 47 Salmonella isolates were serotyped and then subjected to PFGE. Total isolates were analyzed by means of the molecular technique XbaI PFGE. Results: In the current work, PFGE and serotyping were used to subtype 47 Salmonella isolates belonging to 22 different serotypes and derived from poultry. Thirty-nine PFGE patterns out of 47 isolates were obtained. The Discrimination Index (DI by serotyping (0.93 was lower than PFGE (DI = 0.99. Conclusions: In conclusion, molecular methods such as PFGE can be used for epidemiological characterization of Salmonella serotypes.

Molecular typing of Sporothrix schenckii isolates from cats in Malaysia.

Science.gov (United States)

Kano, Rui; Okubo, Miki; Siew, Han Hock; Kamata, Hiroshi; Hasegawa, Atsuhiko

2015-04-01

Epidemiological data on the aetiologic agents of feline sporotrichosis in Malaysia have not been reported, though human sporotrichosis in Malaysia is reported to be transmitted primarily via cat scratch. To the best of our knowledge, the present report is the first study of the molecular epidemiology of Sporothrix schenckii isolates from cats with sporotrichosis in Malaysia. In the present work, we characterised 18 clinical isolates from cats in Malaysia based on molecular properties, including sequence analyses of the calmodulin gene and the rDNA ITS region and selective PCR of mating type (MAT) loci. In this study, isolates from feline sporotrichosis were identified as a S. schenckii sensu stricto by sequence analyses of the calmodulin gene and the internal transcribed spacer (ITS) region. Notably, phylogenetic analysis of the ITS confirmed assignment to clinical clade D (and not C) of S. schenckii sensu stricto. Therefore, clinical clade D of S. schenckii sensu stricto appeared to be the prevailing source of feline sporotrichosis in Malaysia. The ratio of MAT1-1-1:MAT1-2-1 in these Malaysian isolates was found to be 1 : 0. This result suggested that a clonal strain of S. schenckii is the prevailing causative agent of feline sporotrichosis in Malaysia. © 2015 Blackwell Verlag GmbH.

Enhanced sludge reduction in septic tanks by increasing temperature.

Science.gov (United States)

Pussayanavin, Tatchai; Koottatep, Thammarat; Eamrat, Rawintra; Polprasert, Chongrak

2015-01-01

Septic tanks in most developing countries are constructed without drainage trenches or leaching fields to treat toilet wastewater and /or grey water. Due to the short hydraulic retention time, effluents of these septic tanks are still highly polluted, and there is usually high accumulation of septic tank sludge or septage containing high levels of organics and pathogens that requires frequent desludging and subsequent treatment. This study aimed to reduce sludge accumulation in septic tanks by increasing temperatures of the septic tank content. An experimental study employing two laboratory-scale septic tanks fed with diluted septage and operating at temperatures of 40 and 30°C was conducted. At steady-state conditions, there were more methanogenic activities occurring in the sludge layer of the septic tank operating at the temperature of 40°C, resulting in less total volatile solids (TVS) or sludge accumulation and more methane (CH4) production than in the unit operating at 30°C. Molecular analysis found more abundance and diversity of methanogenic microorganisms in the septic tank sludge operating at 40°C than at 30°C. The reduced TVS accumulation in the 40°C septic tank would lengthen the period of septage removal, resulting in a cost-saving in desluging and septage treatment. Cost-benefit analysis of increasing temperatures in septic tanks was discussed.

Isolation and Molecular Characterization of Brucella Isolates in Cattle Milk in Uganda

Directory of Open Access Journals (Sweden)

Denis Rwabiita Mugizi

2015-01-01

Full Text Available Brucellosis is endemic in livestock and humans in Uganda and its transmission involves a multitude of risk factors like consumption of milk from infected cattle. To shed new light on the epidemiology of brucellosis in Uganda the present study used phenotypic and molecular approaches to delineate the Brucella species, biovars, and genotypes shed in cattle milk. Brucella abortus without a biovar designation was isolated from eleven out of 207 milk samples from cattle in Uganda. These isolates had a genomic monomorphism at 16 variable number tandem repeat (VNTR loci and showed in turn high levels of genetic variation when compared with other African strains or other B. abortus biovars from other parts of the world. This study further highlights the usefulness of MLVA as an epidemiological tool for investigation of Brucella infections.

The role and control of sludge age in biological nutrient removal activated sludge systems.

Science.gov (United States)

Ekama, G A

2010-01-01

The sludge age is the most fundamental and important parameter in the design, operation and control of biological nutrient removal (BNR) activated sludge (AS) systems. Generally, the better the effluent and waste sludge quality required from the system, the longer the sludge age, the larger the biological reactor and the more wastewater characteristics need to be known. Controlling the reactor concentration does not control sludge age, only the mass of sludge in the system. When nitrification is a requirement, sludge age control becomes a requirement and the secondary settling tanks can no longer serve the dual purpose of clarifier and waste activated sludge thickeners. The easiest and most practical way to control sludge age is with hydraulic control by wasting a defined proportion of the reactor volume daily. In AS plants with reactor concentration control, nitrification fails first. With hydraulic control of sludge age, nitrification will not fail, rather the plant fails by shedding solids over the secondary settling tank effluent weirs.

Sludge Water Characteristics Under Different Separation Methods from a Membrane Bioreactor

KAUST Repository

Wei, Chunhai

2013-11-22

The concept of sludge water was proposed to integrate the relative terminologies and its characteristics under different separation methods from a membrane bioreactor (MBR) were investigated in this study. Based on chemical oxygen demand (COD) and three-dimensional fluorescence excitation-emission matrix (F-EEM), and compared with the control (gravitational sedimentation), some suspended particulate organics or biopolymer clusters (mainly proteins) were released from sludge flocs into the supernatant after centrifugation under low to middle centrifugal forces (10-4000 g) and then aggregated into a pellet under high centrifugal forces (10000-20000 g). Filtration (1.2 μm glass fiber filter) produced sludge water with a lower biopolymers concentration than the control (gravitational sedimentation followed by filtration) due to cake layer formation during filtration. As for centrifugation followed by filtration, low to middle centrifugal forces did not significantly affect sludge water characteristics but high centrifugal forces reduced the concentrations of some proteins in sludge water from advanced analytical protocols including F-EEM and liquid chromatography with on-line organic carbon detection (LC-OCD), demonstrating a low to middle centrifugal force suitable for MBR sludge water separation. From LC-OCD, the main fractions of sludge water were humic substances and building blocks, low molecular weight neutrals and biopolymers (mainly proteins rather than polysaccharides). Supplemental materials are available for this article. Go to the publisher\\'s online edition of Separation Science and Technology to view the supplemental file. © 2013 Copyright Taylor and Francis Group, LLC.

Sludge Water Characteristics Under Different Separation Methods from a Membrane Bioreactor

KAUST Repository

Wei, Chunhai; Amy, Gary L.

2013-01-01

The concept of sludge water was proposed to integrate the relative terminologies and its characteristics under different separation methods from a membrane bioreactor (MBR) were investigated in this study. Based on chemical oxygen demand (COD) and three-dimensional fluorescence excitation-emission matrix (F-EEM), and compared with the control (gravitational sedimentation), some suspended particulate organics or biopolymer clusters (mainly proteins) were released from sludge flocs into the supernatant after centrifugation under low to middle centrifugal forces (10-4000 g) and then aggregated into a pellet under high centrifugal forces (10000-20000 g). Filtration (1.2 μm glass fiber filter) produced sludge water with a lower biopolymers concentration than the control (gravitational sedimentation followed by filtration) due to cake layer formation during filtration. As for centrifugation followed by filtration, low to middle centrifugal forces did not significantly affect sludge water characteristics but high centrifugal forces reduced the concentrations of some proteins in sludge water from advanced analytical protocols including F-EEM and liquid chromatography with on-line organic carbon detection (LC-OCD), demonstrating a low to middle centrifugal force suitable for MBR sludge water separation. From LC-OCD, the main fractions of sludge water were humic substances and building blocks, low molecular weight neutrals and biopolymers (mainly proteins rather than polysaccharides). Supplemental materials are available for this article. Go to the publisher's online edition of Separation Science and Technology to view the supplemental file. © 2013 Copyright Taylor and Francis Group, LLC.

Radioactivity in sludge: tank cleaning procedures and sludge disposal

International Nuclear Information System (INIS)

Bradley, D.A.

1995-01-01

In the oil and gas industry management of alpha-active sludge is made more complex by the presence of hydrocarbons and heavy metals. This presentation discusses the origin of radioactivity in sludge, management of risk in terms of safe working procedures, storage and possible disposal options. The several options will generally involve aspects of dilution or of concentration; issues to be discussed will include sludge farming, bioremediation and incineration. (author)

Sludge pretreatment chemistry evaluation: Enhanced sludge washing separation factors

International Nuclear Information System (INIS)

Colton, N.G.

1995-03-01

This report presents the work conducted in Fiscal Year 1994 by the Sludge Pretreatment Chemistry Evaluation Subtask for the Tank Waste Remediation System (TWRS) Tank Waste Treatment Science Task. The main purpose of this task, is to provide the technical basis and scientific understanding to support TWRS baseline decisions and actions, such as the development of an enhanced sludge washing process to reduce the volume of waste that will require high-level waste (HLW) vitrification. One objective within the Sludge Pretreatment Chemistry Evaluation Subtask was to establish wash factors for various SST (single-shell tank) sludges. First, analytical data were compiled from existing tank waste characterization reports. These data were summarized on tank-specific worksheets that provided a uniform format for reviewing and comparing data, as well as the means to verify whether the data set for each tank was complete. Worksheets were completed for 27 SST wastes. The analytical water wash data provided tank-specific information about the fraction of each component that dissolves with water, i.e., an estimate of tank-specific wash factors for evaluating tank-by-tank processing. These wash data were then used collectively to evaluate some of the wash factors that are assumed for the overall SST waste inventory; specifically, wash factors for elements that would be found primarily in sludges. The final step in this study was to incorporate the characterization and wash factor data into a spreadsheet that provides insight into the effect of enhanced sludge washing on individual tank sludges as well as for groups of sludges that may be representative of different waste types. Spreadsheet results include the estimated mass and percentage of each element that would be removed with washing and leaching. Furthermore, estimated compositions are given of the final wash and leach streams and residual solids, in terms of both concentration and dry weight percent

Molecular cloning of cellulase genes from indigenous bacterial isolates

International Nuclear Information System (INIS)

Jong Bor Chyan; Pauline Liew Woan Ying; Mat Rasol Awang

2006-01-01

Indigenous cellulolytic bacterial isolates having high activities in degrading carboxymethyl cellulose (CMC) were isolated from local environments. Identification of these isolates were performed by molecular techniques. By using polymerase chain reaction (PCR) techniques, PCR products encoding cellulase gene were amplified from the total genomic DNAs. Purified PCR product was successfully cloned and expressed in Escherichia coli host system. The complete nucleotide sequences of the cellulase genes determined. The analysis of amino acid sequences deduced from the genes indicated that the cloned DNA fragments show high homology to those of endoglucanase genes of family GH5. All cloned genes consist of an N-terminal signal peptide, a catalytic domain of family 5 glycosyl hydrolase and a cellulose-binding domain of family III. (Author)

Virulence and molecular polymorphism of Prunus necrotic ringspot virus isolates.

Science.gov (United States)

Hammond, R W; Crosslin, J M

1998-07-01

Prunus necrotic ringspot virus (PNRSV) occurs as numerous strains or isolates that vary widely in their pathogenic, biophysical and serological properties. Prior attempts to distinguish pathotypes based upon physical properties have not been successful; our approach was to examine the molecular properties that may distinguish these isolates. The nucleic acid sequence was determined from 1.65 kbp RT-PCR products derived from RNA 3 of seven distinct isolates of PNRSV that differ serologically and in pathology on sweet cherry. Sequence comparisons of ORF 3a (putative movement protein) and ORF 3b (coat protein) revealed single nucleotide and amino acid differences with strong correlations to serology and symptom types (pathotypes). Sequence differences between serotypes and pathotypes were also reflected in the overall phylogenetic relationships between the isolates.

Molecular characterization of vancomycin-resistant Enterococcus faecium isolates from Bermuda.

Directory of Open Access Journals (Sweden)

Patrick Eberechi Akpaka

Full Text Available Molecular characteristics of vancomycin resistant enterococci isolates from Bermuda Island is currently unknown. This study was conducted to investigate phenotypic and genotypic characteristics of VRE isolates from Bermuda Island using the chromogenic agar, E-tests, polymerase chain reaction (PCR, pulsed-field gel electrophoresis (PFGE and multilocus sequence typing (MLST. Eighteen E. faecium isolates were completely analyzed and were all resistant to vancomycin, susceptible to linezolid and quinupristin/dalfopristin, positive for vanA and esp genes. The MLST analysis confirmed most isolates were of the sequence types linked to clonal complex 17 (CC17 that is widely associated with outbreaks in hospitals. Infection control measures, antibiotic stewardship, and surveillance activities will continue to be a priority in hospital on the Island.

Mitigation of Hydrogen Gas Generation from the Reaction of Uranium Metal with Water in K Basin Sludge and Sludge Waste Forms

Energy Technology Data Exchange (ETDEWEB)

Sinkov, Sergey I.; Delegard, Calvin H.; Schmidt, Andrew J.

2011-06-08

Prior laboratory testing identified sodium nitrate and nitrite to be the most promising agents to minimize hydrogen generation from uranium metal aqueous corrosion in Hanford Site K Basin sludge. Of the two, nitrate was determined to be better because of higher chemical capacity, lower toxicity, more reliable efficacy, and fewer side reactions than nitrite. The present lab tests were run to determine if nitrate’s beneficial effects to lower H2 generation in simulated and genuine sludge continued for simulated sludge mixed with agents to immobilize water to help meet the Waste Isolation Pilot Plant (WIPP) waste acceptance drainable liquid criterion. Tests were run at ~60°C, 80°C, and 95°C using near spherical high-purity uranium metal beads and simulated sludge to emulate uranium-rich KW containerized sludge currently residing in engineered containers KW-210 and KW-220. Immobilization agents tested were Portland cement (PC), a commercial blend of PC with sepiolite clay (Aquaset II H), granulated sepiolite clay (Aquaset II G), and sepiolite clay powder (Aquaset II). In all cases except tests with Aquaset II G, the simulated sludge was mixed intimately with the immobilization agent before testing commenced. For the granulated Aquaset II G clay was added to the top of the settled sludge/solution mixture according to manufacturer application directions. The gas volumes and compositions, uranium metal corrosion mass losses, and nitrite, ammonia, and hydroxide concentrations in the interstitial solutions were measured. Uranium metal corrosion rates were compared with rates forecast from the known uranium metal anoxic water corrosion rate law. The ratios of the forecast to the observed rates were calculated to find the corrosion rate attenuation factors. Hydrogen quantities also were measured and compared with quantities expected based on non-attenuated H2 generation at the full forecast anoxic corrosion rate to arrive at H2 attenuation factors. The uranium metal

Mitigation of Hydrogen Gas Generation from the Reaction of Uranium Metal with Water in K Basin Sludge and Sludge Waste Forms

International Nuclear Information System (INIS)

Sinkov, Sergey I.; Delegard, Calvin H.; Schmidt, Andrew J.

2011-01-01

Prior laboratory testing identified sodium nitrate and nitrite to be the most promising agents to minimize hydrogen generation from uranium metal aqueous corrosion in Hanford Site K Basin sludge. Of the two, nitrate was determined to be better because of higher chemical capacity, lower toxicity, more reliable efficacy, and fewer side reactions than nitrite. The present lab tests were run to determine if nitrate's beneficial effects to lower H2 generation in simulated and genuine sludge continued for simulated sludge mixed with agents to immobilize water to help meet the Waste Isolation Pilot Plant (WIPP) waste acceptance drainable liquid criterion. Tests were run at ∼60 C, 80 C, and 95 C using near spherical high-purity uranium metal beads and simulated sludge to emulate uranium-rich KW containerized sludge currently residing in engineered containers KW-210 and KW-220. Immobilization agents tested were Portland cement (PC), a commercial blend of PC with sepiolite clay (Aquaset II H), granulated sepiolite clay (Aquaset II G), and sepiolite clay powder (Aquaset II). In all cases except tests with Aquaset II G, the simulated sludge was mixed intimately with the immobilization agent before testing commenced. For the granulated Aquaset II G clay was added to the top of the settled sludge/solution mixture according to manufacturer application directions. The gas volumes and compositions, uranium metal corrosion mass losses, and nitrite, ammonia, and hydroxide concentrations in the interstitial solutions were measured. Uranium metal corrosion rates were compared with rates forecast from the known uranium metal anoxic water corrosion rate law. The ratios of the forecast to the observed rates were calculated to find the corrosion rate attenuation factors. Hydrogen quantities also were measured and compared with quantities expected based on non-attenuated H2 generation at the full forecast anoxic corrosion rate to arrive at H2 attenuation factors. The uranium metal

K basins sludge removal sludge pretreatment system

International Nuclear Information System (INIS)

Chang, H.L.

1997-01-01

The Spent Nuclear Fuels Program is in the process of planning activities to remove spent nuclear fuel and other materials from the 100-K Basins as a remediation effort for clean closure. The 105 K- East and K-West Basins store spent fuel, sludge, and debris. Sludge has accumulated in the 1 00 K Basins as a result of fuel oxidation and a slight amount of general debris being deposited, by settling, in the basin water. The ultimate intent in removing the sludge and fuel is to eliminate the environmental risk posed by storing fuel at the K Basins. The task for this project is to disposition specific constituents of sludge (metallic fuel) to produce a product stream through a pretreatment process that will meet the requirements, including a final particle size acceptable to the Tank Waste Remediation System (TWRS). The purpose of this task is to develop a preconceptual design package for the K Basin sludge pretreatment system. The process equipment/system is at a preconceptual stage, as shown in sketch ES-SNF-01 , while a more refined process system and material/energy balances are ongoing (all sketches are shown in Appendix C). Thus, the overall process and 0535 associated equipment have been conservatively selected and sized, respectively, to establish the cost basis and equipment layout as shown in sketches ES- SNF-02 through 08

Diversity, Localization, and Physiological Properties of Filamentous Microbes Belonging to Chloroflexi Subphylum I in Mesophilic and Thermophilic Methanogenic Sludge Granules

Science.gov (United States)

Yamada, Takeshi; Sekiguchi, Yuji; Imachi, Hiroyuki; Kamagata, Yoichi; Ohashi, Akiyoshi; Harada, Hideki

2005-01-01

We previously reported that the thermophilic filamentous anaerobe Anaerolinea thermophila, which is the first cultured representative of subphylum I of the bacterial phylum Chloroflexi, not only was one of the predominant constituents of thermophilic sludge granules but also was a causative agent of filamentous sludge bulking in a thermophilic (55°C) upflow anaerobic sludge blanket (UASB) reactor in which high-strength organic wastewater was treated (Y. Sekiguchi, H. Takahashi, Y. Kamagata, A. Ohashi, and H. Harada, Appl. Environ. Microbiol. 67:5740-5749, 2001). To further elucidate the ecology and function of Anaerolinea-type filamentous microbes in UASB sludge granules, we surveyed the diversity, distribution, and physiological properties of Chloroflexi subphylum I microbes residing in UASB granules. Five different types of mesophilic and thermophilic UASB sludge were used to analyze the Chloroflexi subphylum I populations. 16S rRNA gene cloning-based analyses using a 16S rRNA gene-targeted Chloroflexi-specific PCR primer set revealed that all clonal sequences were affiliated with the Chloroflexi subphylum I group and that a number of different phylotypes were present in each clone library, suggesting the ubiquity and vast genetic diversity of these populations in UASB sludge granules. Subsequent fluorescence in situ hybridization (FISH) of the three different types of mesophilic sludge granules using a Chloroflexi-specific probe suggested that all probe-reactive cells had a filamentous morphology and were widely distributed within the sludge granules. The FISH observations also indicated that the Chloroflexi subphylum I bacteria were not always the predominant populations within mesophilic sludge granules, in contrast to thermophilic sludge granules. We isolated two mesophilic strains and one thermophilic strain belonging to the Chloroflexi subphylum I group. The physiological properties of these isolates suggested that these populations may contribute to the

Sludge minimization technologies - an overview

Energy Technology Data Exchange (ETDEWEB)

Oedegaard, Hallvard

2003-07-01

The management of wastewater sludge from wastewater treatment plants represents one of the major challenges in wastewater treatment today. The cost of the sludge treatment amounts to more that the cost of the liquid in many cases. Therefore the focus on and interest in sludge minimization is steadily increasing. In the paper an overview is given for sludge minimization (sludge mass reduction) options. It is demonstrated that sludge minimization may be a result of reduced production of sludge and/or disintegration processes that may take place both in the wastewater treatment stage and in the sludge stage. Various sludge disintegration technologies for sludge minimization are discussed, including mechanical methods (focusing on stirred ball-mill, high-pressure homogenizer, ultrasonic disintegrator), chemical methods (focusing on the use of ozone), physical methods (focusing on thermal and thermal/chemical hydrolysis) and biological methods (focusing on enzymatic processes). (author)

Filterability of membrane bioreactor (MBR) sludge: impacts of polyelectrolytes and mixing with conventional activated sludge.

Science.gov (United States)

Yigit, Nevzat O; Civelekoglu, Gokhan; Cinar, Ozer; Kitis, Mehmet

2010-01-01

The main objective of this work was to investigate the filterability of MBR sludge and its mixture with conventional activated sludge (CAS). In addition, the impacts of type and dose of various polyelectrolytes, filter type and sludge properties on the filterability of both MBR and Mixed sludges were determined. Specific cake resistance (SCR) measured by the Buchner funnel filtration test apparatus and the solids content of the resulting sludge cake were used to assess the dewaterability of tested sludges. The type of filter paper used in Buchner tests affected the results of filterability for MBR, CAS and Mixed sludges. SCR values and optimum polyelectrolyte doses increased with increasing MLSS concentrations in the MBR, which suggested that increase in MLSS concentrations accompanied by increases in EPS and SMP concentrations and a shift toward smaller particles caused poorer dewaterability of the MBR sludge. The significant differences observed among the filterability of CAS and MBR sludges suggested that MLSS alone is not a good predictor of sludge dewaterability. Combining CAS and MBR sludges at different proportions generally improved their dewaterability. Combining MBR sludges having typically high MLSS and EPS concentrations with CAS having much lower MLSS concentrations may be an option for full-scale treatment plants experiencing sludge dewaterability problems. Better filterability and higher cake dry solids were achieved with cationic polyelectrolytes compared to anionic and non-ionic ones for all sludge types tested.

An exploration of the effect and interaction mechanism of bisphenol A on waste sludge hydrolysis with multi-spectra, isothermal titration microcalorimetry and molecule docking.

Science.gov (United States)

Hou, Guangying; Zhang, Rui; Hao, Xiaoyan; Liu, Chunguang

2017-07-05

An increasing amount of bisphenol A (BPA) is being produced and used, then discharged into sewage treatment plants and accumulated in sludge or soil, when the sludge is used as fertilizer. Accumulation of BPA in sludge or soil causes poisoning to the enzyme, which affects the biological treatment of sludge and the circulation and conversion of materials in soil. In this research, effect of BPA on sludge hydrolysis is studied from the respect of concentration and components of soluble organic matter in sludge, using three-dimensional fluorescence spectra. In order to illuminate the interaction mechanism, toxic effect of BPA on α-Amylase (a model of hydrolase in sludge) is investigated with multi-spectra, isothermal titration microcalorimetry and molecule docking at the molecular level. Results show that the secondary structure of α-Amylase and the microenvironment of amino acid residue in α-Amylase are changed. The molecular docking study and ITC results show that hydrophobic bond and hydrogen bond exist in the interaction between BPA and α-Amylase. Based on the above analysis and enzyme activity assay, sludge hydrolysis is inhibited due to the denaturation of α-Amylase with BPA exposure. Copyright © 2017 Elsevier B.V. All rights reserved.

Treatment of petroleum industry oil sludge by Rhodotorula sp

Energy Technology Data Exchange (ETDEWEB)

Shailubhai, K.; Rao, N.N.; Modi, V.V.

1984-06-01

A Rhodotorula sp., isolated from soil, which showed a versatile capacity to degrade various aromatic and aliphatic hydrocarbons, was used to treat oil sludge. As a result of treatment, there was significant decrease in BOD, COD and contents of various petroleum fractions. The susceptibility to degradation was in the following order: saturate fraction >aromatic fraction> asphaltic fraction.

INNOVATIVE REMEDIATION AND MONITORING SYSTEM INSIDE AN AREA USED FOR PAPER SLUDGE RECOVERY

Directory of Open Access Journals (Sweden)

Valerio Marroni

2010-12-01

Full Text Available An innovative bioremediation technology and strategy were applied to a former-quarry area in Imola (BO – Italy concerned by an incorrect environmental restoration of paper sludge, with subsequent uncontrolled biogas production and migration to the adjacent area. An Emergency Plan was implemented by the isolation of the buried sludge area and a characterization project was performed to define an appropriate permanently safe recovery. An innovative biological in situ treatment, avoiding paper sludge removal, was adopted; it was based on the use of tailored compost and enzymes to reduce methane production and concentration. This was integrated by specific monitoring piezometers for both biogas (CH4, CO2 and oxygen monthly measurements, and also the application of a respirometric technique application to buried sludge for assessing its stabilisation under aerobic and anaerobic conditions. This communication describes the strategy used, the treatment and monitoring system and the results of 3 years field pilot application. Monitoring work is still in progress.

Molecular screening and isolation of Newcastle disease virus from ...

African Journals Online (AJOL)

Molecular screening and isolation of Newcastle disease virus from live poultry markets and chickens from commercial poultry farms in Zaria, Kaduna state, Nigeria. ... The PDF file you selected should load here if your Web browser has a PDF reader plug-in installed (for example, a recent version of Adobe Acrobat Reader).

Molecular characterization of acquired enrofloxacin resistance in Mycoplasma synoviae field isolates.

Science.gov (United States)

Lysnyansky, I; Gerchman, I; Mikula, I; Gobbo, F; Catania, S; Levisohn, S

2013-07-01

The in vitro activity of enrofloxacin against 73 Mycoplasma synoviae field strains isolated in Israel and Europe was determined by broth microdilution. Decreased susceptibility to enrofloxacin was identified in 59% of strains, with the MICs ranging from 1 to >16 μg/ml. The estimated MIC50 and MIC90 values for enrofloxacin were 2 and 8 μg/ml, respectively. Moreover, this study showed that 92% of recent Israeli field isolates (2009 to 2011) of M. synoviae have MICs of ≥ 2 μg/ml to enrofloxacin. Comparison of the quinolone resistance-determining regions (QRDRs) in M. synoviae isolates revealed a clear correlation between the presence of one of the amino acid substitutions Asp79-Asn, Thr80-Ala/Ile, Ser81-Pro, and Asp84-Asn/Tyr/His of the ParC QRDR and decreased susceptibility to enrofloxacin (MIC, ≥ 1 μg/ml). Amino acid substitutions at positions GyrA 87, GyrB 401/402, and ParE 420/454 were also identified, but there was no clear-cut correlation with susceptibility to enrofloxacin. Comparison of vlhA molecular profiles revealed the presence of 9 different genotypes in the Israeli M. synoviae field isolates and 10 genotypes in the European isolates; only one vlhA genotype (type 4) was identified in both cohorts. Based on results of vlhA molecular typing, several mechanisms for emergence and dissemination of Israeli enrofloxacin-resistant M. synoviae isolates are suggested.

Removal of oxytetracycline and determining its biosorption properties on aerobic granular sludge.

Science.gov (United States)

Mihciokur, Hamdi; Oguz, Merve

2016-09-01

This study investigates biosorption of Oxytetracycline, a broad-spectrum antibiotic, using aerobic granular sludge as an adsorbent in aqueous solutions. A sequencing batch reactor fed by a synthetic wastewater was operated to create aerobic granular sludge. Primarily, the pore structure and surface area of granular sludge, the chemical structure and the molecular sizes of the pharmaceutical, operating conditions, such as pH, stirring rate, initial concentration of Oxytetracycline, during adsorption process was verified. Subsequently, thermodynamic and kinetic aspects of the adsorption were examined and adsorption isotherm studies were carried out. It was shown that the aerobic granular sludge was a good alternative for biosorption of this pharmaceutical. The pharmaceutical was adsorbed better at pH values of 6-8. The adsorption efficiency increased with rising ionic strength. Also, it was seen that the adsorption process was an exothermic process in terms of thermodynamics. The adsorption can be well explained by Langmuir isotherm model. Copyright © 2016 Elsevier B.V. All rights reserved.

Ultrasonically enhanced disintegration. Polymers, sludge, and contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Groenroos, A.

2010-05-15

There are a great variety of potential applications of high-intensity ultrasonic energy. Of these, cleaning, plastic pounding, and at present also sludge disintegration and the remediation of contaminated soil are probably the best known and offer the most general market for high-intensity ultrasonics. All developments within the area of ultrasound applications lead to the creation of environmentally friendly processes and compounds, emphasizing the role of ultrasound in 'green chemistry'. Ultrasound technology is considered not easy to use in industrial processes, since devices providing high sonic energy are not easy to construct. This thesis investigates on a semi-pilot scale if it is possible to enhance the disintegration of three quite different samples: polymers, sludge, and contaminated soil by using ultrasound. The results indicate that it is possible to enhance the disintegration of polymers by means of ultrasonic power only when the cavitation threshold is exceeded. Above the cavitation threshold, the most extensive degradation took place at the lowest ultrasonic frequency used. The biggest decrease (from 115,000 g/mol to 30,000 g/mol) in relative molecular mass (RMM) was observed when the concentration of polyvinyl alcohol (PVA) was the lowest (1.0%). However, in the case of carboxymethylcellulose (CMC) it was observed that when viscosity was not adjusted there is an optimum polymer concentration (1.5-2.0%) where degradation is most efficient. The thesis shows that the extent of ultrasonic depolymerization decreases with decreasing molecular mass of the CMC polymer. The study also reveals that ultrasonic irradiation causes narrowing of the molecular mass distribution. The degradation of CMC polymer proceeded linearly and the rate of ultrasonic depolymerization decreased with decreasing molecular mass. In cases where the initial dynamic viscosities of polymer solutions were not the same, the sonolytic degradation of CMC polymer mainly depended

Critical operational parameters for zero sludge production in biological wastewater treatment processes combined with sludge disintegration.

Science.gov (United States)

Yoon, Seong-Hoon; Lee, Sangho

2005-09-01

Mathematical models were developed to elucidate the relationships among process control parameters and the effect of these parameters on the performance of anoxic/oxic biological wastewater processes combined with sludge disintegrators (A/O-SD). The model equations were also applied for analyses of activated sludge processes hybrid with sludge disintegrators (AS-SD). Solubilization ratio of sludge in the sludge disintegrator, alpha, hardly affected sludge reduction efficiencies if the biomass was completely destructed to smaller particulates. On the other hand, conversion efficiency of non-biodegradable particulates to biodegradable particulates, beta, significantly affected sludge reduction efficiencies because beta was directly related to the accumulation of non-biodegradable particulates in bioreactors. When 30% of sludge in the oxic tank was disintegrated everyday and beta was 0.5, sludge reduction was expected to be 78% and 69% for the A/O-SD and AS-SD processes, respectively. Under this condition, the sludge disintegration number (SDN), which is the amount of sludge disintegrated divided by the reduced sludge, was calculated to be around 4. Due to the sludge disintegration, live biomass concentration decreased while other non-biodegradable particulates concentration increased. As a consequence, the real F/M ratio was expected to be much higher than the apparent F/M. The effluent COD was maintained almost constant for the range of sludge disintegration rate considered in this study. Nitrogen removal efficiencies of the A/O-SD process was hardly affected by the sludge disintegration until daily sludge disintegration reaches 40% of sludge in the oxic tank. Above this level of sludge disintegration, autotrophic biomass concentration decreases overly and TKN in the effluent increases abruptly in both the A/O-SD and AS-SD processes. Overall, the trends of sludge reduction and effluent quality according to operation parameters matched well with experimental results

Effects of Sludge-amendment on Mineralization of Pyrene and Microorganisms in Sludge and Soil

DEFF Research Database (Denmark)

Klinge, C; Gejlsbjerg, B; Ekelund, Flemming

2001-01-01

. Sludge-amendment enhanced the mineralization of pyrene in the soil compared to soil without sludge, and the most extensive mineralization was observed when the sludge was kept in a lump. The number of protozoa, heterotrophic bacteria and pyrene-mineralizing bacteria was much higher in the sludge compared...... to the soil. The amendment of sludge did not affect the number of protozoa and bacteria in the surrounding soil, which indicated that organic contaminants in the sludge had a little effect on the number of protozoa and bacteria in the surrounding soil...

Molecular characterization of multidrug-resistant Mycobacterium tuberculosis isolated in Nepal.

Science.gov (United States)

Poudel, Ajay; Nakajima, Chie; Fukushima, Yukari; Suzuki, Haruka; Pandey, Basu Dev; Maharjan, Bhagwan; Suzuki, Yasuhiko

2012-06-01

Despite the fact that Nepal is one of the first countries globally to introduce multidrug-resistant tuberculosis (MDR-TB) case management, the number of MDR-TB cases is continuing to rise in Nepal. Rapid molecular tests applicable in this setting to identify resistant organisms would be an effective tool in reversing this trend. To develop such tools, information about the frequency and distribution of mutations that are associated with phenotypic drug resistance in Mycobacterium tuberculosis is required. In the present study, we investigated the prevalence of mutations in rpoB and katG genes and the inhA promoter region in 158 M. tuberculosis isolates (109 phenotypically MDR and 49 non-MDR isolates collected in Nepal) by DNA sequencing. Mutations affecting the 81-bp rifampin (RIF) resistance-determining region (RRDR) of rpoB were identified in 106 of 109 (97.3%) RIF-resistant isolates. Codons 531, 526, and 516 were the most commonly affected, at percentages of 58.7, 15.6, and 15.6%, respectively. Of 113 isoniazid (INH)-resistant isolates, 99 (87.6%) had mutations in the katG gene, with Ser315Thr being the most prevalent (81.4%) substitution. Mutations in the inhA promoter region were detected in 14 (12.4%) INH-resistant isolates. The results from this study provide an overview of the current situation of RIF and INH resistance in M. tuberculosis in Nepal and can serve as a basis for developing or improving rapid molecular tests to monitor drug-resistant strains in this country.

Removal of hydrocarbon from refinery tank bottom sludge employing microbial culture.

Science.gov (United States)

Saikia, Rashmi Rekha; Deka, Suresh

2013-12-01

Accumulation of oily sludge is becoming a serious environmental threat, and there has not been much work reported for the removal of hydrocarbon from refinery tank bottom sludge. Effort has been made in this study to investigate the removal of hydrocarbon from refinery sludge by isolated biosurfactant-producing Pseudomonas aeruginosa RS29 strain and explore the biosurfactant for its composition and stability. Laboratory investigation was carried out with this strain to observe its efficacy of removing hydrocarbon from refinery sludge employing whole bacterial culture and culture supernatant to various concentrations of sand-sludge mixture. Removal of hydrocarbon was recorded after 20 days. Analysis of the produced biosurfactant was carried out to get the idea about its stability and composition. The strain could remove up to 85 ± 3 and 55 ± 4.5 % of hydrocarbon from refinery sludge when whole bacterial culture and culture supernatant were used, respectively. Maximum surface tension reduction (26.3 mN m(-1)) was achieved with the strain in just 24 h of time. Emulsification index (E24) was recorded as 100 and 80 % with crude oil and n-hexadecane, respectively. The biosurfactant was confirmed as rhamnolipid containing C8 and C10 fatty acid components and having more mono-rhamnolipid congeners than the di-rhamnolipid ones. The biosurfactant was stable up to 121 °C, pH 2-10, and up to a salinity value of 2-10 % w/v. To our knowledge, this is the first report showing the potentiality of a native strain from the northeast region of India for the efficient removal of hydrocarbon from refinery sludge.

Effect of seed sludge on characteristics and microbial community of aerobic granular sludge.

Science.gov (United States)

Song, Zhiwei; Pan, Yuejun; Zhang, Kun; Ren, Nanqi; Wang, Aijie

2010-01-01

Aerobic granular sludge was cultivated by using different kinds of seed sludge in sequencing batch airlift reactor. The influence of seed sludge on physical and chemical properties of granular sludge was studied; the microbial community structure was probed by using scanning electron microscope and polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE). The results showed that seed sludge played an important role on the formation of aerobic granules. Seed sludge taken from beer wastewater treatment plant (inoculum A) was more suitable for cultivating aerobic granules than that of sludge from municipal wastewater treatment plant (inoculum B). Cultivated with inoculum A, large amount of mature granules formed after 35 days operation, its SVI reached 32.75 mL/g, and SOUR of granular sludge was beyond 1.10 mg/(g x min). By contrast, it needed 56 days obtaining mature granules using inoculum B. DGGE profiles indicated that the dominant microbial species in mature granules were 18 and 11 OTU when inoculum A and B were respectively employed as seed sludge. The sequencing results suggested that dominant species in mature granules cultivated by inoculum A were Paracoccus sp., Devosia hwasunensi, Pseudoxanthomonas sp., while the dominant species were Lactococcus raffinolactis and Pseudomonas sp. in granules developed from inoculum B.

Enhancement of biogas production from sewage sludge by addition of grease trap sludge

International Nuclear Information System (INIS)

Grosser, A.; Neczaj, E.

2016-01-01

Highlights: • Addition of grease trap sludge is interesting option for sewage sludge digestion. • Co-digestion of grease trap sludge and sewage sludge improved efficiency of process. • The anaerobic digestion can be carried out at short hydraulic retention time. • Long chain fatty acids concentration was below the ranges for inhibition of anaerobic digestion. - Abstract: Despite having many benefits, a low degree of volatile solids removal as well as long retention time are the main factors limiting the performance of the anaerobic digestion. Co-digestion of sewage sludge with other organic waste (for example fat rich materials) is one of the few potential ways to enhance the performance of the anaerobic digestion. In this article, the effects of adding fatty rich materials on the performance and stability of semi-continuous anaerobic digestion of sewage sludge were investigated on a 6 l laboratory-scale reactor (working volume equal to 5.5 l). The reactor was operated in a semi-continuous mode with a hydraulic retention time of 10 days. The data presented in this paper relate to the period in which the grease trap sludge accounted for 10, 12, 14, 16 and 18% of the mixture on the volatile solids basis. The results clearly indicate that the addition of fat rich materials like grease trap sludge can lead to a satisfactory increase in biogas yield in digester treating sewage sludge. The results showed that co-digestion can enhance the biogas yield by 28–82% compared to anaerobic digestion of sewage sludge alone (control sample). Moreover, the addition of grease trap sludge to digesters resulted in increased volatile solids removal from 44.38% (control sample) to 57.77% (feedstock with 14% addition of grease trap sludge). It was found that the increase of grease trap sludge in the feedstock had a direct impact on the biogas production and methane yield. This proposal has also been confirmed by statistical analysis such as Pearson correlation coefficients and

Impact of sludge properties on solid-liquid separation of activated sludge

DEFF Research Database (Denmark)

Christensen, Morten Lykkegaard

2016-01-01

Solid-liquid separation of activated sludge is important both directly after the biological treatment of wastewater and for sludge dewatering. The separation of solid from the treated wastewater can be done by clarifiers (conventional plants) or membrane (MBR). Further, part of the sludge is taken...... out from the proces and usually dewatered before further handling. The separation process is costly. Moreover, the separation process depends on the composition and the properties of the sludge. The best separation is obtained for sludge that contains strong, compact flocs without single cells...... and dissolved extracellular polymeric substances (EPS). Polyvalent ions improve the floc strangth and improve the separation whereas monovalent ions (e.g. from road salt, sea water intrusion and industry) reduces impair the separation. Further high pH impairs the separation process due to floc disintegration...

Wasting Away: To Sludge or Not to Sludge?

Directory of Open Access Journals (Sweden)

L Nicolle

2001-01-01

Full Text Available Following a century of high standards of sanitation, food and water safety in North America are often taken for granted. Recent outbreaks of illness attributed to food and water contamination, however, have challenged this complacency. Now, sludge is added to the list of concerns. Sewage sludge is the muddy substance that remains after the treatment of municipal sewage. This material includes not only human waste, but also household and industrial toxic wastes disposed of in local sewers. Federal and provincial Canadian regulations support the use of this material as fertilizer, within acceptable guidelines, as does the Environmental Protection Agency in the United States. The safety of sludge, however, is questioned by some individuals and groups. Specifically, the risk of infectious agents and toxins to workers or other exposed individuals, and the potential for heavy metals and organic chemicals to be transferred from sludge-treated fields into crops are concerns.

Carbon-14 in sludge

International Nuclear Information System (INIS)

Fowler, J.R.; Coleman, C.J.

1983-01-01

The level of C-14 in high-level waste is needed to establish the amount of C-14 that will be released to the environment either as off-gas from the Defense Waste Processing Facility (DWPF) or as a component of saltstone. Available experimental data confirmed a low level of C-14 in soluble waste, but no data was available for sludge. Based on the processes used in each area, Purex LAW sludge in F-area and HM HAW sludge in H-area will contain the bulk of any sludge produced by the cladding. Accordingly, samples from Tank 8F containing Purex LAW and Tank 15H containing HM HAW were obtained and analyzed for C-14. These two waste types constitute approximately 70% of the total sludge inventory now stored in the waste tanks. Results from analyses of these two sludge types show: the total C-14 inventory in sludge now stored in the waste tanks is 6.8 Ci; C-14 releases to the atmosphere from the DWPF will average approximately 0.6 Ci annually at the projected sludge processing rate in the DWPF. 4 references, 2 tables

Micrococcus flavus sp. nov., isolated from activated sludge in a bioreactor.

Science.gov (United States)

Liu, Xing-Yu; Wang, Bao-Jun; Jiang, Cheng-Ying; Liu, Shuang-Jiang

2007-01-01

Bacterial strain LW4(T) was isolated from activated sludge of a wastewater-treatment bioreactor. Cells of strain LW4(T) were Gram-positive cocci, with a diameter of 0.7-1.0 microm. Colonies produced on LB agar plates were yellow, smooth, circular and 0.5-1.5 mm in diameter. Strain LW4(T) was aerobic and grew over the temperature range 26-34 degrees C and pH range 5-9, with optimal growth at 30.5-31.5 degrees C and pH 6.0-6.2. The cell-wall peptidoglycan of strain LW4(T) contained amino acid residues of lysine, glutamic acid, alanine, glycine and aspartic acid. The most abundant cellular fatty acids of strain LW4(T) were anteiso-C(15 : 0) (32.15 %) and iso-C(15 : 0) (31.65 %). Major respiratory quinones were MK-8(H(2)) (57.3 %) and MK-7(H(2)) (32.9 %). The DNA G+C content was 71.4 mol% (T(m)). 16S rRNA gene sequence analysis indicated that strain LW4(T) was phylogenetically related to members of the genus Micrococcus, with similarities ranging from 96.5 to 97.3 %. Levels of DNA-DNA relatedness of strain LW4(T) to Micrococcus luteus DSM 20030(T), Micrococcus lylae DSM 20315(T) and Micrococcus antarcticus AS 1.2372(T) were 55, 48 and 36 %, respectively. Based on these results, it is concluded that strain LW4(T) represents a novel species of the genus Micrococcus, for which the name Micrococcus flavus sp. nov. is proposed. The type strain is strain LW4(T) (=CGMCC 1.5361(T)=JCM 14000(T)).

Isolation and Characterization of PHA-Producing Bacteria from Propylene Oxide Saponification Wastewater Residual Sludge.

Science.gov (United States)

Li, Ruirui; Gu, Pengfei; Fan, Xiangyu; Shen, Junyu; Wu, Yulian; Huang, Lixuan; Li, Qiang

2018-03-21

A polyhydroxyalkanoate (PHA)-producing strain was isolated from propylene oxide (PO) saponification wastewater activated sludge and was identified as Brevundimonas vesicularis UJN1 through 16S rDNA sequencing and Biolog microbiological identification. Single-factor and response surface methodology experiments were used to optimize the culture medium and conditions. The optimal C/N ratio was 100/1.04, and the optimal carbon and nitrogen sources were sucrose (10 g/L) and NH 4 Cl (0.104 g/L) respectively. The optimal culture conditions consisted of initial pH of 6.7 and an incubation temperature of 33.4 °C for 48 h, with 15% inoculum and 100 mL medium at an agitation rate of 180 rpm. The PHA concentration reached 34.1% of the cell dry weight and increased three times compared with that before optimization. The only report of PHA-producing bacteria by Brevundimonas vesicularis showed that the conversion rate of PHAs using glucose as the optimal carbon source was 1.67%. In our research, the conversion rate of PHAs with sucrose as the optimal carbon source was 3.05%, and PHA production using sucrose as the carbon source was much cheaper than that using glucose as the carbon source.

Toxicity evaluation and prediction of toxic chemicals on activated sludge system.

Science.gov (United States)

Cai, Bijing; Xie, Li; Yang, Dianhai; Arcangeli, Jean-Pierre

2010-05-15

The gaps of data for evaluating toxicity of new or overloaded organic chemicals on activated sludge system resulted in the requirements for methodology of toxicity estimation. In this study, 24 aromatic chemicals typically existed in the industrial wastewater were selected and classified into three groups of benzenes, phenols and anilines. Their toxicity on activated sludge was then investigated. Two indexes of IC(50-M) and IC(50-S) were determined respectively from the respiration rates of activated sludge with different toxicant concentration at mid-term (24h) and short-term (30min) time intervals. Experimental results showed that the group of benzenes was the most toxic, followed by the groups of phenols and anilines. The values of IC(50-M) of the tested chemicals were higher than those of IC(50-S). In addition, quantitative structure-activity relationships (QSARs) models developed from IC(50-M) were more stable and accurate than those of IC(50-S). The multiple linear models based on molecular descriptors and K(ow) presented better reliability than single linear models based on K(ow). Among these molecular descriptors, E(lumo) was the most important impact factor for evaluation of mid-term toxicity. Copyright (c) 2009 Elsevier B.V. All rights reserved.

Protists as bioindicators in activated sludge: Identification, ecology and future needs.

Science.gov (United States)

Foissner, Wilhelm

2016-08-01

When the activated sludge process was developed, operators and scientists soon recognized protists as valuable indicators. However, only when Curds et al. (1968) showed with a few photographs the need of ciliates for a clear plant effluent, sewage protistology began to bloom but was limited by the need of species identification. Still, this is a major problem although several good guides are available. Thus, molecular kits should be developed for identification. Protists are indicators in two stages of wastewater treatment, viz., in the activated sludge and in the environmental water receiving the plant effluent. Continuous control of the protist and bacterial communities can prevent biological sludge foaming and bulking and may greatly save money for sludge oxygenation because several protist species are excellent indicators for the amount of oxygen present. The investigation of the effluent-receiving rivers gives a solid indication about the long term function of sewage works. The literature on protist bioindication in activated sludge is widely distributed. Thus, I compiled the data in a simple Table, showing which communities and species indicate good, mediocre, or poor plant performance. Further, many details on indication are provided, such as sludge loading and nitrifying conditions. Such specific features should be improved by appropriate statistics and more reliable identification of species. Then, protistologists have a fair chance to become important in wastewater works. Activated sludge is a unique habitat for particular species, often poorly or even undescribed. As an example, I present two new species. The first is a minute (∼30μm) Metacystis that makes an up to 300μm-sized mucous envelope mimicking a sludge floc. The second is a Phialina that is unique in having the contractile vacuole slightly posterior to mid-body. Finally, I provide a list of species which have the type locality in sewage plants. Copyright © 2016 Elsevier GmbH. All rights

Nuclear safety of extended sludge processing on tank 42 and 51 sludge (DWPF sludge feed batch one)

International Nuclear Information System (INIS)

Clemons, J.S.

1993-01-01

The sludge in tanks 42 and 51 is to be washed with inhibited water to remove soluble salts and combined in tank 51 in preparation for feed to DWPF. Since these tanks contain uranium and plutonium, the process of washing must be evaluated to ensure subcriticality is maintained. When the sludge is washed, inhibited water is added, the tank contents are slurried and allowed to settle. The sludge wash water is then decanted to the evaporator feed tank where it is fed to the evaporator to reduce the volume. The resulting evaporator concentrate is sent to a salt tank where it cools and forms crystallized salt cake. This salt cake will later be dissolved, processed in ITP and sent to Z-Area. This report evaluates the supernate and sludge during washing, the impact on the evaporator during concentration of decanted wash water, and the salt tank where the concentrated supernate is deposited. The conclusions generated in this report are specific to the sludge currently contained in tanks 42 and 51

Thermophilic slurry-phase treatment of petroleum hydrocarbon waste sludges

International Nuclear Information System (INIS)

Castaldi, F.J.; Bombaugh, K.J.; McFarland, B.

1995-01-01

Chemoheterotrophic thermophilic bacteria were used to achieve enhanced hydrocarbon degradation during slurry-phase treatment of oily waste sludges from petroleum refinery operations. Aerobic and anaerobic bacterial cultures were examined under thermophilic conditions to assess the effects of mode of metabolism on the potential for petroleum hydrocarbon degradation. The study determined that both aerobic and anaerobic thermophilic bacteria are capable of growth on petroleum hydrocarbons. Thermophilic methanogenesis is feasible during the degradation of hydrocarbons when a strict anaerobic condition is achieved in a slurry bioreactor. Aerobic thermophilic bacteria achieved the largest apparent reduction in chemical oxygen demand, freon extractable oil, total and volatile solid,s and polycyclic aromatic hydrocarbons (PAHs) when treating oily waste sludges. The observed shift with time in the molecular weight distribution of hydrocarbon material was more pronounced under aerobic metabolic conditions than under strict anaerobic conditions. The changes in the hydrocarbon molecular weight distribution, infrared spectra, and PAH concentrations during slurry-phase treatment indicate that the aerobic thermophilic bioslurry achieved a higher degree of hydrocarbon degradation than the anaerobic thermophilic bioslurry during the same time period

Sludge busters

Energy Technology Data Exchange (ETDEWEB)

Pichon, Max

2010-07-15

Full text: A few years ago, For Earth developed low energy sub-surface aeration systems to increase the biological activity in the wastewater sludge ponds. Then came the idea to introduce probiotic bacteria to really ramp up the process, which promises massive time and cost savings in sludge management. Increasing the volumes of specific bacteria reactivates the sludge, accelerating biological nutrient removal in general and, by tailoring the bacteria, targeting specific organic waste types. The technology is already running at more than 30 councils across NSW and in some commercial settings, such as dairy farms. Shane McKibbin, GM of For Earth, said the 'Probiotic, Low Energy Aeration System' offers considerable upside. “The cost savings have been enormous with some councils, including the work done at Woolgoolga Water Reclamation Plant at Coffs Harbour,” he said. Sludge settling in wastewater treatment plant lagoons is typically pumped out, centrifuged to remove water and then landfilled. In Woolgoolga's case that process was costing Coffs Harbour Water $150 a cubic metre; McKibbin said they've slashed that to a measly $5 a cubic metre. An array of 'industrial air stones' is dropped 1m below the surface to create an oxygenated blanket across the surface, overcoming the tendency of sludge ponds to stagnate. The key though is floating probiotic dosing lines across the surface, which kick-starts the probiotics process. “Previously, some operators just wanted to throw it on with a bucket, so the bacteria would get thrown into one corner of the pond. But since we introduced the dosing system it has really improved the overall performance,” said McKibbin.The dosing pump system automatically applies the bacteria into the dosing line according to a specified program, ensuring the probiotics are spread out across the pond and across the week. “I would say it improves and accelerates the result by 30 per cent,” he adds. “The biggest problem was that

Sludge busters

International Nuclear Information System (INIS)

Pichon, Max

2010-01-01

Full text: A few years ago, For Earth developed low energy sub-surface aeration systems to increase the biological activity in the wastewater sludge ponds. Then came the idea to introduce probiotic bacteria to really ramp up the process, which promises massive time and cost savings in sludge management. Increasing the volumes of specific bacteria reactivates the sludge, accelerating biological nutrient removal in general and, by tailoring the bacteria, targeting specific organic waste types. The technology is already running at more than 30 councils across NSW and in some commercial settings, such as dairy farms. Shane McKibbin, GM of For Earth, said the 'Probiotic, Low Energy Aeration System' offers considerable upside. “The cost savings have been enormous with some councils, including the work done at Woolgoolga Water Reclamation Plant at Coffs Harbour,” he said. Sludge settling in wastewater treatment plant lagoons is typically pumped out, centrifuged to remove water and then landfilled. In Woolgoolga's case that process was costing Coffs Harbour Water $150 a cubic metre; McKibbin said they've slashed that to a measly $5 a cubic metre. An array of 'industrial air stones' is dropped 1m below the surface to create an oxygenated blanket across the surface, overcoming the tendency of sludge ponds to stagnate. The key though is floating probiotic dosing lines across the surface, which kick-starts the probiotics process. “Previously, some operators just wanted to throw it on with a bucket, so the bacteria would get thrown into one corner of the pond. But since we introduced the dosing system it has really improved the overall performance,” said McKibbin.The dosing pump system automatically applies the bacteria into the dosing line according to a specified program, ensuring the probiotics are spread out across the pond and across the week. “I would say it improves and accelerates the result by 30 per cent,” he adds. “The biggest problem was that

Isolation and identification of molecular species of phosphatidylcholine and lysophosphatidylcholine from jojoba seed meal (Simmondsia chinensis).

Science.gov (United States)

Léon, Fabian; Van Boven, Maurits; de Witte, Peter; Busson, Roger; Cokelaere, Marnix

2004-03-10

A mixture of lysophosphatidylcholine (LPC) and phosphatidylcholine (PC) has been isolated by column chromatography from a jojoba meal (Simmondsia chinensis) extract. The molecular species of both classes could be separated and isolated by C18 reversed phase HPLC. The two major compounds were identified by 1D and 2D (1)H and (13)C NMR, by MS, and by GC-MS as 1-oleoyl-3-lysophosphatidylcholine and 1,2-dioleoyl-3-phosphatidylcholine. Eight other molecular species of LPC and four other molecular species of PC could be assigned by comparison of the mass spectra of the isolated compounds with the spectra of the two major compounds. Complete characterization of the individual molecular species was achieved by GC and GC-MS analysis of the fatty acyl composition from the isolated compounds. The PC/LPC proportion in the phospholipid mixture from three different samples is 1.6 +/- 0.1. LPC is considered to be an important bioactive compound; the results of this study suggest further research for the evaluation of potential health benefits of jojoba meal phospholipids.

Sludge Stabilization Campaign blend plan

International Nuclear Information System (INIS)

De Vries, M.L.

1994-01-01

This sludge stabilization blend plan documents the material to be processed and the order of processing for the FY95 Sludge Stabilization Campaign. The primary mission of this process is to reduce the inventory of unstable plutonium bearing sludge. The source of the sludge is residual and glovebox floor sweepings from the production of material at the Plutonium Finishing Plant (PFP). The reactive sludge is currently being stored in various gloveboxes at PFP. There are two types of the plutonium bearing material that will be thermally stabilized in the muffle furnace: Plutonium Reclamation Facility (PRF) sludge and Remote Mechanical C (RMC) Line material

Characterization and migration of oil and solids in oily sludge during centrifugation.

Science.gov (United States)

Wang, Jun; Han, Xu; Huang, Qunxing; Ma, Zengyi; Chi, Yong; Yan, Jianhua

2018-05-01

The migration behaviors of oil, water and solids in sludge during centrifugation were elaborated. Size distribution, surface topography and lypohydrophilic properties were studied in detail. The average size of solids was 61 μm in original sludge, 31 μm in upper layer and 235 μm in bottom layer. The result shows that solvent is essential to separate oil phase into molecular light and weight fractions during centrifugation. With solvent/oil ratio increases from 1:2, 1:1, 2:1 to 5:1, molecular weight in upper layer decreases from 1044, 1043, 1020 to 846 combined with that in bottom layer increases. A model was proposed to calculate the oil residue content in solid phases after sedimentation. The findings of this paper provide information for optimizing the oil recovery and clean treatment.

Molecular docking of viscosine as a new lipoxygenase inhibitor isolated from Dodonaea viscosa

Directory of Open Access Journals (Sweden)

Amir Zada Khan

2013-03-01

Full Text Available Viscosine was isolated from Dodonaea viscosa, which showed significant lipoxygenase inhibitory activity (IC50: value 39 ± 0.17. Molecular docking simulations were conducted to explore molecular binding mode, and to help elucidate molecular mechanism behind its significant inhibitory activity. Molecular interactions of viscosine with catalytic triad (His523, His518, Ile875 inside active site of lipoxygenase via hydrogen bonding, seems to be the major factor involved in its significant lipoxygenase inhibitory activity.

Pseudoclavibacter caeni sp. nov., isolated from sludge of a sewage disposal plant.

Science.gov (United States)

Srinivasan, Sathiyaraj; Kim, Hyun Sook; Kim, Myung Kyum; Lee, Myungjin

2012-04-01

A Gram-positive, strictly aerobic, rod-shaped, non-motile bacterial strain, designated MJ28T, was isolated from a sludge sample from the Daejeon sewage disposal plant in South Korea. A polyphasic approach was applied to study the taxonomic position of strain MJ28T. Strain MJ28T showed highest 16S rRNA gene sequence similarity to Pseudoclavibacter soli KP02T (95.2 %). Levels of 16S rRNA gene sequence similarity to the type strains of other Pseudoclavibacter species were less than 94.0 %. Phylogenetic analysis based on 16S rRNA gene sequences showed that strain MJ28T belonged to the clade formed by members of the genus Pseudoclavibacter in the family Microbacteriaceae. The G+C content of the genomic DNA of strain MJ28T was 65.8 mol%. The chemotaxonomic characteristics of strain MJ28T showed features typical of the genus Pseudoclavibacter, with MK-9 as the predominant respiratory quinone, 2,4-diaminobutryic acid as the diamino acid in the peptidoglycan, and anteiso-C17:0 (44.6 %), anteiso-C15:0 (35.7 %) and C16:0 (9.5 %) as the major fatty acids. On the basis of phylogenetic inference, fatty acid profile and other phenotypic properties, strain MJ28T is considered to represent a novel species of the genus Pseudoclavibacter, for which the name Pseudoclavibacter caeni sp. nov. is proposed. The type strain is MJ28T (=KCTC 19773T=JCM 16921T).

Rhodanobacter caeni sp. nov., isolated from sludge from a sewage disposal plant.

Science.gov (United States)

Woo, Sung-Geun; Srinivasan, Sathiyaraj; Kim, Myung Kyum; Lee, Myungjin

2012-12-01

Two Gram-reaction-negative, motile bacteria, designated strains MJ01(T) and MJ14, were isolated from sludge collected from the Daejeon sewage disposal plant in South Korea. The taxonomic positions of both strains were determined using a polyphasic approach. In phylogenetic analyses based on 16S rRNA gene sequences, strains MJ01(T) and MJ14 appeared indistinguishable and to be most closely related to members of the genus Rhodanobacter in the family Xanthomonadaceae of the Gammaproteobacteria (96.4-98.8% sequence similarity). Strain MJ01(T) exhibited a relatively high level of DNA-DNA relatedness with strain MJ14 (89.3 %) but relatively low DNA-DNA relatedness values with established species in the genus Rhodanobacter (<60 %). The genomic DNA G+C contents of strains MJ01(T) and MJ14 were 65.3 and 64.8 mol%, respectively. The major respiratory quinone of both novel strains was the ubiquinone Q-8. The major fatty acids of both strains were iso-C(15 : 0), iso-C(16 : 0), iso-C(17:0) and iso-C(17 : 1)ω9c, and the polar lipid profiles of the two strains contained diphosphatidylglycerol, phosphatidylglycerol, phosphatidylethanolamine and minor amounts of unidentified aminophospholipids and phospholipids. Based on the phenotypic, genotypic and phylogenetic evidence, strains MJ01(T) and MJ14 represent a single novel species in the genus Rhodanobacter, for which the name Rhodanobacter caeni sp. nov. is proposed. The type strain is MJ01(T) ( = KCTC 22449(T) = JCM 16242(T)), with MJ14 ( = KCTC 22460 = JCM 16243) as a reference strain.

Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings.

Science.gov (United States)

Larsen, Julie D; Nielsen, Steen M; Scheutz, Charlotte

2017-11-01

Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during the resting period. As the resting period proceeded, atmospheric air re-entered the pore space at all depth levels. The methane (CH 4 ) concentration was at its highest during the first part of the resting period, and then declined as the sludge residue became more dewatered and thereby aerated. In the pore space, the concentration of CH 4 often exceeded the concentration of carbon dioxide (CO 2 ). However, the total emission of CO 2 from the surface of the sludge residue exceeded the total emission of CH 4 , suggesting that CO 2 was mainly produced in the layer of newly applied sludge and/or that CO 2 was emitted from the sludge residue more readily compared to CH 4 .

Sludge recovery apparatus

International Nuclear Information System (INIS)

Marmo, A.R.

1979-01-01

An improved design of a sludge recovery apparatus used in the fabrication of nuclear fuel is described. This apparatus provides for automatic separation of sludge from the grinder coolant, drying of the sludge into a flowable powder and transfer of the dry powder to a salvage container. It can be constructed to comply with criticality-safe-geometry requirements and to obviate need for operating personnel in its immediate vicinity. (UK)

Linking toxicity profiles to pollutants in sludge and sediments

Czech Academy of Sciences Publication Activity Database

Stiborová, H.; Kolář, Michal; Vrkoslavová, J.; Pulkrabová, J.; Hajslova, J.; Demnerová, K.; Uhlík, O.

2017-01-01

Roč. 321, zima (2017), s. 672-680 ISSN 0304-3894 R&D Projects: GA ČR(CZ) GA15-02328S Institutional support: RVO:68378050 Keywords : polycyclic aromatic-hydrocarbons * Toxicity * Contamination * Sludge * Sediments * Priority pollutants * Constrained correspondence analysis (CCS) Subject RIV: EB - Genetics ; Molecular Biology OBOR OECD: Other biological topics Impact factor: 6.065, year: 2016

Control of electron localization to isolate and enhance molecular harmonic plateau in asymmetric HeH2+ system

International Nuclear Information System (INIS)

Lu, Ruifeng; Yu, Chao; Wang, Yunhui; Shi, Qi; Zhang, Yadong

2014-01-01

High-order harmonic generation from the asymmetric molecular ion HeH 2+ exposed to intense laser fields was investigated by quantum wave packet calculations in which the initial wave packet of HeH 2+ was prepared in the first excited 2pσ state. The calculated molecular harmonic plateau at low frequencies was effectively isolated and enhanced by adjusting the carrier-envelope phase (CEP) of the laser field. Furthermore, double-well model, time-dependent electronic density, electronic state population, and time-frequency analyses were presented to explain the underlying mechanism of the efficient isolated molecular plateau. By taking advantage of the CEP effect to control the electronic dynamics, this isolated molecular plateau can be used to generate high-intensity single attosecond pulses.

Management Of Hanford KW Basin Knockout Pot Sludge As Spent Nuclear Fuel

International Nuclear Information System (INIS)

Raymond, R. E.; Evans, K. M.

2012-01-01

CH2M Hill Plateau Remediation Company (CHPRC) and AREVA Federal Services, LLC (AFS) have been working collaboratively to develop and deploy technologies to remove, transport, and interim store remote-handled sludge from the 10S-K West Reactor Fuel Storage Basin on the U.S. Department of Energy (DOE) Hanford Site near Richland, WA, USA. Two disposal paths exist for the different types of sludge found in the K West (KW) Basin. One path is to be managed as Spent Nuclear Fuel (SNF) with eventual disposal at an SNF at a yet to be licensed repository. The second path will be disposed as remote-handled transuranic (RH-TRU) waste at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, NM. This paper describes the systems developed and executed by the Knockout Pot (KOP) Disposition Subproject for processing and interim storage of the sludge managed as SNF, (i.e., KOP material)

Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings

DEFF Research Database (Denmark)

Larsen, Julie Dam; Nielsen, Steen M; Scheutz, Charlotte

2017-01-01

Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological...... processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during...

Sludge technology assessment

International Nuclear Information System (INIS)

Krause, T.R.; Cunnane, J.C.; Helt, J.E.

1994-12-01

The retrieval, processing, and generation of final waste forms from radioactive tank waste sludges present some of the most challenging technical problems confronting scientists and engineers responsible for the waste management programs at the various Department of Energy laboratories and production facilities. Currently, the Department of Energy is developing a strategy to retrieve, process, and generate a final waste form for the sludge that meets the acceptance criteria for the final disposition. An integral part of this strategy will be use of separation processes that treat the sludge; the goal is to meet feed criteria for the various processes that will generate the final waste form, such as vitrification or grouting. This document is intended to (1) identify separation technologies which are being considered for sludge treatment at various DOE sites, (2) define the current state of sludge treatment technology, (3) identify what research and development is required, (4) identify current research programs within either DOE or academia developing sludge treatment technology, and (5) identify commercial separation technologies which may be applicable. Due to the limited scope of this document, technical evaluations regarding the need for a particular separations technology, the current state of development, or the research required for implementation, are not provided

Phenotypic and molecular identification of Fonsecaea pedrosoi strains isolated from chromoblastomycosis patients in Mexico and Venezuela.

Science.gov (United States)

Carolina Rojas, O; León-Cachón, Rafael B R; Pérez-Maya, Antonio Alí; Aguirre-Garza, Marcelino; Moreno-Treviño, María G; González, Gloria M

2015-05-01

Chromoblastomycosis is a chronic granulomatous disease caused frequently by fungi of the Fonsecaea genus. The objective of this study was the phenotypic and molecular identification of F. pedrosoi strains isolated from chromoblastomycosis patients in Mexico and Venezuela. Ten strains were included in this study. For phenotypic identification, we used macroscopic and microscopic morphologies, carbohydrate assimilation test, urea hydrolysis, cixcloheximide tolerance, proteolitic activity and the thermotolerance test. The antifungal activity of five drugs was evaluated against the isolates. Molecular identification was performed by sequencing the internal transcribed spacer (ITS) ribosomal DNA regions of the isolated strains. The physiological analysis and morphological features were variable and the precise identification was not possible. All isolates were susceptible to itraconazole, terbinafine, voriconazole and posaconazole. Amphotericin B was the least effective drug. The alignment of the 559-nucleotide ITS sequences from our strains compared with sequences of GenBank revealed high homology with F. pedrosoi (EU285266.1). In this study, all patients were from rural areas, six from Mexico and four from Venezuela. Ten isolates were identified by phenotypic and molecular analysis, using ITS sequence and demonstrated that nine isolates from Mexico and Venezuela were 100% homologous and one isolate showed a small genetic distance. © 2015 Blackwell Verlag GmbH.

Activated sludge model No. 3

DEFF Research Database (Denmark)

Gujer, W.; Henze, M.; Mino, T.

1999-01-01

The Activated Sludge Model No. 3 (ASM3) can predict oxygen consumption, sludge production, nitrification and denitrification of activated sludge systems. It relates to the Activated Sludge Model No. 1 (ASM1) and corrects for some defects of ASM I. In addition to ASM1, ASM3 includes storage of org...

Species identification and molecular typing of human Brucella isolates from Kuwait.

Science.gov (United States)

Mustafa, Abu S; Habibi, Nazima; Osman, Amr; Shaheed, Faraz; Khan, Mohd W

2017-01-01

Brucellosis is a zoonotic disease of major concern in Kuwait and the Middle East. Human brucellosis can be caused by several Brucella species with varying degree of pathogenesis, and relapses are common after apparently successful therapy. The classical biochemical methods for identification of Brucella are time-consuming, cumbersome, and provide information limited to the species level only. In contrast, molecular methods are rapid and provide differentiation at intra-species level. In this study, four molecular methods [16S rRNA gene sequencing, real-time PCR, enterobacterial repetitive intergenic consensus (ERIC)-PCR and multilocus variable-number tandem-repeat analysis (MLVA)-8, MLVA-11 and MLVA-16 were evaluated for the identification and typing of 75 strains of Brucella isolated in Kuwait. 16S rRNA gene sequencing of all isolates showed 90-99% sequence identity with B. melitensis and real-time PCR with genus- and species- specific primers identified all isolates as B. melitensis. The results of ERIC-PCR suggested the existence of 75 ERIC genotypes of B. melitensis with a discriminatory index of 0.997. Cluster classification of these genotypes divided them into two clusters, A and B, diverging at ~25%. The maximum number of genotypes (n = 51) were found in cluster B5. MLVA-8 analysis identified all isolates as B. melitensis, and MLVA-8, MLVA-11 and MLVA-16 typing divided the isolates into 10, 32 and 71 MLVA types, respectively. Furthermore, the combined minimum spanning tree analysis demonstrated that, compared to MLVA types discovered all over the world, the Kuwaiti isolates were a distinct group of MLVA-11 and MLVA-16 types in the East Mediterranean Region.

Efficiency of a pilot-scale integrated sludge thickening and digestion reactor in treating low-organic excess sludge.

Science.gov (United States)

He, Qiang; Li, Jiang; Liu, Hongxia; Tang, Chuandong; de Koning, Jaap; Spanjers, Henri

2012-06-01

The sludge production from medium- and small-scale wastewater treatment plants in the Three Gorges Reservoir Region is low and non-stable; especially, the organic content in this sludge is low (near 40% of VS/TS). An integrated thickening and digestion (ISTD) reactor was developed to treat this low-organic excess sludge. After a flow test and start-up experiment of the reactor, a running experiment was used to investigate the excess sludge treatment efficiency under five different excess sludge inflows: 200, 300, 400, 500 and 400 L/d (a mixture of excess sludge and primary sludge in a volume ratio of 9:1). This trial was carried out in the wastewater treatment plant in Chongqing, which covers 80% of the Three Gorges Reservoir Region, under the following conditions: (1) sludge was heated to 38-40 degrees C using an electrical heater to maintain anaerobic mesophilic digestion; (2) the biogas produced was recirculated to mix raw sludge with anaerobic sludge in the reactor under the flow rate of 12.5 L/min. There were three main results. Firstly, the flow pattern of the inner reactor was almost completely mixed under the air flow of 12.0 L/min using clear water. Secondly, under all the different sludge inflows, the water content in the outlet sludge was below 93%. Thirdly, the organic content in the outlet sludge was decreased from 37% to 30% and from 24% to 20%, whose removal ratio was in relation to the organic content of the inlet sludge. The excess sludge treatment capacity of the ISTD reactor was according to the organic content in the excess sludge.

Molecular Detection and Characterization of Goat Isolate of Taenia hydatigena in Turkey

Directory of Open Access Journals (Sweden)

Armagan Erdem Utuk

2012-01-01

Full Text Available The aim of this study was to provide molecular detection and characterization of the goat isolate of Taenia hydatigena from Ankara province of Turkey. For this purpose, PCR amplification of small subunit ribosomal RNA (rrnS and partial sequencing of mitochondrial cytochrome c oxidase subunit 1 (mt-CO1 genes were performed in a one-month-old dead goat. According to rrnS-PCR results, parasites were identified as Taenia spp., and partial sequence of mt-CO1 gene was corresponding to T. hydatigena. At the end of the study, we concluded that molecular tools can be used to define species of parasites in cases where the key morphologic features cannot be detected. Nucleotide sequence data of Turkish goat isolate of T. hydatigena was submitted to GenBank for other researchers interested in this subject. By this study, molecular detection and characterization of T. hydatigena was done for the first time in Turkey.

Radiation hygienization of raw sewage sludge

International Nuclear Information System (INIS)

Shah, M.R.; Lavale, D.S.; Rawat, P.; Benny, P.G.; Sharma, A.K.; Dey, G.R.; Bhave, V.

2001-01-01

'Radiation treatment of municipal sewage sludge can achieve resource conservation and recovery objectives. The liquid sludge irradiator of Sludge Hygienization Research Irradiator at Baroda (India) was operated for generating data on treatment of raw sludge containing 3-4 % solids. The plant system was modified for irradiating raw sludge without affecting basic irradiator initially designed to treat digested sludge. Hourly samples were analysed for estimation of disinfection dose requirement. Sand separated from the sludge was used as in-situ dosimeter by making use of its thermoluminescence property. Investigations are being carried out for regrowth of Total Coliforms in the sludge samples from this irradiator. Possibility of inadequate treatment due to geometric configuration of irradiator is being checked. (author)

Sewage sludges disinfection

International Nuclear Information System (INIS)

Alexandre, D.; Gevaudan, P.P.

1977-01-01

There is a hygienic risk in using biological sewage sludges for agriculture. Systematic analyses carried out on sludge samples obtained from purification plants in the Eastern and Southern part of France, show the almost uniform presence of pathogenic microorganisms. Some of them survive more than nine months after application to the soil. Conventional processes for disinfection, liming and heat, make the sludge unsuitable for agricultural use. On the other hand, irradiation involves no modification of structure and composition of sludges. Radiation doses required for disinfection vary according to the type of microorganism. Some of them are eliminated at rather low doses (200 krad), but mycobacteria, viruses and eggs of worms resist to more important doses. The security dose is estimated to be approx. 1000 krad

STATUS OF MECHANICAL SLUDGE REMOVAL AND COOLING COILS CLOSURE AT THE SAVANNAH RIVER SITE - F TANK FARM CLOSURE PORJECT -9225

International Nuclear Information System (INIS)

Jolly, R.

2009-01-01

The Savannah River Site F-Tank Farm Closure project has successfully performed Mechanical Sludge Removal using the Waste on Wheels (WOW) system within two of its storage tanks. The Waste on Wheels (WOW) system is designed to be relatively mobile with the ability for many components to be redeployed to multiple tanks. It is primarily comprised of Submersible Mixer Pumps (SMPs), Submersible Transfer Pumps (STPs), and a mobile control room with a control panel and variable speed drives. These tanks, designated as Tank 6 and Tank 5 respectively, are Type I waste tanks located in F-Tank Farm (FTF) with a capacity of 2839 cubic meters (750,000 gallons) each. In addition, Type I tanks have 34 vertically oriented cooling coils and two horizontal cooling coil circuits along the tank floor. DOE intends to remove from service and operationally close Tank 5 and Tank 6 and other HLW tanks that do not meet current containment standards. After obtaining regulatory approval, the tanks and cooling coils will be isolated and filled with grout for long term stabilization. Mechanical Sludge Removal of the remaining sludge waste within Tank 6 removed ∼ 75% of the original 25,000 gallons in August 2007. Utilizing lessons learned from Tank 6, Tank 5 Mechanical Sludge Removal completed removal of ∼ 90% of the original 125 cubic meters (33,000 gallons) of sludge material in May 2008. The successful removal of sludge material meets the requirement of approximately 19 to 28 cubic meters (5,000 to 7,500 gallons) remaining prior to the Chemical Cleaning process. The Chemical Cleaning Process will utilize 8 wt% oxalic acid to dissolve the remaining sludge heel. The flow sheet for Chemical Cleaning planned a 20:1 volume ratio of acid to sludge for the first strike with mixing provided by the submersible mixer pumps. The subsequent strikes will utilize a 13:1 volume ratio of acid to sludge with no mixing. The results of the Chemical Cleaning Process are detailed in the 'Status of Chemical

STATUS OF MECHANICAL SLUDGE REMOVAL AND COOLING COILS CLOSURE AT THE SAVANNAH RIVER SITE - F TANK FARM CLOSURE PROJECT - 9225

Energy Technology Data Exchange (ETDEWEB)

Jolly, R

2009-01-06

The Savannah River Site F-Tank Farm Closure project has successfully performed Mechanical Sludge Removal using the Waste on Wheels (WOW) system within two of its storage tanks. The Waste on Wheels (WOW) system is designed to be relatively mobile with the ability for many components to be redeployed to multiple tanks. It is primarily comprised of Submersible Mixer Pumps (SMPs), Submersible Transfer Pumps (STPs), and a mobile control room with a control panel and variable speed drives. These tanks, designated as Tank 6 and Tank 5 respectively, are Type I waste tanks located in F-Tank Farm (FTF) with a capacity of 2839 cubic meters (750,000 gallons) each. In addition, Type I tanks have 34 vertically oriented cooling coils and two horizontal cooling coil circuits along the tank floor. DOE intends to remove from service and operationally close Tank 5 and Tank 6 and other HLW tanks that do not meet current containment standards. After obtaining regulatory approval, the tanks and cooling coils will be isolated and filled with grout for long term stabilization. Mechanical Sludge Removal of the remaining sludge waste within Tank 6 removed {approx} 75% of the original 25,000 gallons in August 2007. Utilizing lessons learned from Tank 6, Tank 5 Mechanical Sludge Removal completed removal of {approx} 90% of the original 125 cubic meters (33,000 gallons) of sludge material in May 2008. The successful removal of sludge material meets the requirement of approximately 19 to 28 cubic meters (5,000 to 7,500 gallons) remaining prior to the Chemical Cleaning process. The Chemical Cleaning Process will utilize 8 wt% oxalic acid to dissolve the remaining sludge heel. The flow sheet for Chemical Cleaning planned a 20:1 volume ratio of acid to sludge for the first strike with mixing provided by the submersible mixer pumps. The subsequent strikes will utilize a 13:1 volume ratio of acid to sludge with no mixing. The results of the Chemical Cleaning Process are detailed in the &apos

Molecular characterization of the first leptospires isolated from goats in Brazil

Directory of Open Access Journals (Sweden)

Walter Lilenbaum

2014-12-01

Full Text Available Two Leptospira sp. isolates were obtained by the first time from goats in Brazil and characterized by sequencing rrs, rpoB and secY genes, PFGE and typing with monoclonal antibodies. Both isolates are identical and belong to Leptospira santarosai. Analysis of the rrs and the rpoB genes sequences revealed 100% identity between the goat isolates and the Bananal reference strain. When secY sequences of the two isolates were compared to each other, it was observed that they had identical sequences. However, when compared to that of the Bananal reference strain, there were 15 mismatches along the 549 bp secY sequence. In conclusion, molecular methods are increasingly useful for the characterization of leptospires and allowed to identify those isolates of caprine origin as closely related but not identical to serovar Bananal, and constitute a new type named Carioca.

Isolation and biochemical and molecular characterization of Listeria monocytogenes in food

International Nuclear Information System (INIS)

Helel, Salma

2008-01-01

monocytogenes is a Gram-positive bacteria, saprophytic, non-spore. This is an extremely resistant seeds to environmental conditions outside, especially since the cold psychrotrophic. It can contaminate raw vegetables, cooked meals ready for consumption or foods to be stored in the refrigerator, such as cheese or meat. It is the bacteria responsible for listeriosis. It threatens first unborn children, infants, pregnant women, the elderly and people whose immune system is weakened. Strains of Listeria spp isolated from foods (seafood, meat, meat) were first identified at the stage of the genus by classical tests (Gram staining, catalase test, oxidase test and mobility) and stage of the test case by hemolysis, CAMP test and the gallery Api Listeria. Biochemical characterization allowed after a numerical analysis, to assign 100% of isolates to the genus Listeria. Molecular characterization was performed by PCR amplification of genes coding for protein p60 (iap), the listeriolysine O (hly), the Phosphatidylinositol Phospholipase C (PI-PLC plca) Phosphatidylcholine Phospholipase C (plcB). The result showed an amplification of the iap gene of 100% of the hly gene, plca, plcB of 31.81%. This characterization represents an identification of the collection on the genetic level and shows that 31.81% of isolates, is likely to express the genes responsible for virulence factors of L. monocytogenes, to produce listeriolysine O, phospholipase C and Lecithinase. The molecular identification was performed by microarray technique and identified isolates L. September monocytogenes (five original clinical isolates and two food-borne), fourteen L. innocua (of food) and a strain not identified by DNA chip.. (Author)

Improvement of sludge dewaterability and removal of sludge-borne metals by bioleaching at optimum pH.

Science.gov (United States)

Liu, Fenwu; Zhou, Lixiang; Zhou, Jun; Song, Xingwei; Wang, Dianzhan

2012-06-30

Bio-acidification caused by bio-oxidation of energy substances during bioleaching is widely known to play an important role in improving sludge-borne metals removal. Here we report that bioleaching also drastically enhances sludge dewaterability in a suitable pH level. To obtain the optimum initial concentrations of energy substances and pH values for sludge dewaterability during bioleaching, bio-oxidation of Fe(2+) and S(0) under co-inoculation with Acidithiobacillus thiooxidans TS6 and Acidothiobacillus ferrooxidans LX5 and their effects on sludge dewaterability and metals removal during sludge bioleaching were investigated. Results indicated that the dosage of energy substances with 2g/L S(0) and 2g/L Fe(2+) could obtain bio-oxidation efficiencies of up to 100% for Fe(2+) and 50% for S(0) and were the optimal dosages for sludge bioleaching. The removal efficiencies of sludge-borne Cu and Cr could reach above 85% and 40%, respectively, and capillary suction time (CST) of bioleached sludge decreased to as low as ∼10s from initial 48.9s for fresh sludge when sludge pH declined to ∼2.4 through bioleaching. These results confirm the potential of bioleaching as a novel method for improving sludge dewaterability as well as removal of metals. Copyright © 2012 Elsevier B.V. All rights reserved.

Cost and effectiveness comparisons of various types of sludge irradiation and sludge pasteurization treatments

International Nuclear Information System (INIS)

Morris, M.E.

1976-01-01

The radiation from 137 Cs, a major constituent of nuclear fuel reprocessing waste, can be used to sterilize sewage sludge. This paper compares the effectiveness and cost of heat pasteurization, irradiation, and thermoradiation (simultaneous heating/irradiation), three competing methods of sludge disinfection. The cost of irradiation and thermoradiation is slightly higher than heat pasteurization costs for liquid sludges, although minor changes in oil availability or prices could change this. If the viral destruction could be done easily by other means, a 500-kilorad irradiation dose would be effective and less costly. For dry sewage sludges, irradiation is as effective and much less costly than any of the liquid sludge disinfection processes. Irradiation of compost appears to be cheaper and more practical than any heat pasteurization process for the dry sludge (the insulating property of the compost makes heating difficult). 6 tables, 2 fig

F-Canyon Sludge Physical Properties

International Nuclear Information System (INIS)

Poirier, M. R.; Hansen, P. R.; Fink, S. D.

2005-01-01

The Site Deactivation and Decommissioning (SDD) Organization is evaluating options to disposition the 800 underground tanks (including removal of the sludge heels from these tanks). To support this effort, DandD requested assistance from Savannah River National Laboratory (SRNL) personnel to determine the pertinent physical properties to effectively mobilize the sludge from these tanks (Tanks 804, 808, and 809). SDD provided SRNL with samples of the sludge from Tanks 804, 808, and 809. The authors measured the following physical properties for each tank: particle settling rate, shear strength (i.e., settled solids yield stress), slurry rheology (i.e., yield stress and consistency), total solids concentration in the sludge, soluble solids concentration of the sludge, sludge density, and particle size distribution

SLUDGE TREATMENT PROJECT PHASE 1 SLUDGE STORAGE OPTIONS. ASSESSMENT OF T PLANT VERSUS ALTERNATE STORAGE FACILITY

International Nuclear Information System (INIS)

Rutherford, W.W.; Geuther, W.J.; Strankman, M.R.; Conrad, E.A.; Rhoadarmer, D.D.; Black, D.M.; Pottmeyer, J.A.

2009-01-01

The CH2M HILL Plateau Remediation Company (CHPRC) has recommended to the U.S. Department of Energy (DOE) a two phase approach for removal and storage (Phase 1) and treatment and packaging for offsite shipment (Phase 2) of the sludge currently stored within the 105-K West Basin. This two phased strategy enables early removal of sludge from the 105-K West Basin by 2015, allowing remediation of historical unplanned releases of waste and closure of the 100-K Area. In Phase 1, the sludge currently stored in the Engineered Containers and Settler Tanks within the 105-K West Basin will be transferred into sludge transport and storage containers (STSCs). The STSCs will be transported to an interim storage facility. In Phase 2, sludge will be processed (treated) to meet shipping and disposal requirements and the sludge will be packaged for final disposal at a geologic repository. The purpose of this study is to evaluate two alternatives for interim Phase 1 storage of K Basin sludge. The cost, schedule, and risks for sludge storage at a newly-constructed Alternate Storage Facility (ASF) are compared to those at T Plant, which has been used previously for sludge storage. Based on the results of the assessment, T Plant is recommended for Phase 1 interim storage of sludge. Key elements that support this recommendation are the following: (1) T Plant has a proven process for storing sludge; (2) T Plant storage can be implemented at a lower incremental cost than the ASF; and (3) T Plant storage has a more favorable schedule profile, which provides more float, than the ASF. Underpinning the recommendation of T Plant for sludge storage is the assumption that T Plant has a durable, extended mission independent of the K Basin sludge interim storage mission. If this assumption cannot be validated and the operating costs of T Plant are borne by the Sludge Treatment Project, the conclusions and recommendations of this study would change. The following decision-making strategy, which is

SLUDGE TREATMENT PROJECT PHASE 1 SLUDGE STORAGE OPTIONS ASSESSMENT OF T PLANT VERSUS ALTERNATE STORAGE FACILITY

Energy Technology Data Exchange (ETDEWEB)

RUTHERFORD WW; GEUTHER WJ; STRANKMAN MR; CONRAD EA; RHOADARMER DD; BLACK DM; POTTMEYER JA

2009-04-29

The CH2M HILL Plateau Remediation Company (CHPRC) has recommended to the U.S. Department of Energy (DOE) a two phase approach for removal and storage (Phase 1) and treatment and packaging for offsite shipment (Phase 2) of the sludge currently stored within the 105-K West Basin. This two phased strategy enables early removal of sludge from the 105-K West Basin by 2015, allowing remediation of historical unplanned releases of waste and closure of the 100-K Area. In Phase 1, the sludge currently stored in the Engineered Containers and Settler Tanks within the 105-K West Basin will be transferred into sludge transport and storage containers (STSCs). The STSCs will be transported to an interim storage facility. In Phase 2, sludge will be processed (treated) to meet shipping and disposal requirements and the sludge will be packaged for final disposal at a geologic repository. The purpose of this study is to evaluate two alternatives for interim Phase 1 storage of K Basin sludge. The cost, schedule, and risks for sludge storage at a newly-constructed Alternate Storage Facility (ASF) are compared to those at T Plant, which has been used previously for sludge storage. Based on the results of the assessment, T Plant is recommended for Phase 1 interim storage of sludge. Key elements that support this recommendation are the following: (1) T Plant has a proven process for storing sludge; (2) T Plant storage can be implemented at a lower incremental cost than the ASF; and (3) T Plant storage has a more favorable schedule profile, which provides more float, than the ASF. Underpinning the recommendation of T Plant for sludge storage is the assumption that T Plant has a durable, extended mission independent of the K Basin sludge interim storage mission. If this assumption cannot be validated and the operating costs of T Plant are borne by the Sludge Treatment Project, the conclusions and recommendations of this study would change. The following decision-making strategy, which is

Fate of return activated sludge after ozonation: an optimization study for sludge disintegration.

Science.gov (United States)

Demir, Ozlem; Filibeli, Ayse

2012-09-01

The effects of ozonation on sludge disintegration should be investigated before the application of ozone during biological treatment, in order to minimize excess sludge production. In this study, changes in sludge and supernatant after ozonation of return activated sludge were investigated for seven different ozone doses. The optimum ozone dose to avoid inhibition of ozonation and high ozone cost was determined in terms of disintegration degree as 0.05 g O3/gTS. Suspended solid and volatile suspended solid concentrations of sludge decreased by 77.8% and 71.6%, respectively, at the optimum ozone dose. Ozonation significantly decomposed sludge flocs. The release of cell contents was proved by the increase of supernatant total nitrogen (TN) and phosphorus (TP). While TN increased from 7 mg/L to 151 mg/L, TP increased from 8.8 to 33 mg/L at the optimum ozone dose. The dewaterability and filterability characteristics of the ozonated sludge were also examined. Capillary suction time increased with increasing ozone dosage, but specific resistance to filtration increased to a specific value and then decreased dramatically. The particle size distribution changed significantly as a result of floc disruption at an optimum dose of 0.05 gO3/gTS.

Polymer Film-Based Screening and Isolation of Polylactic Acid (PLA)-Degrading Microorganisms.

Science.gov (United States)

Kim, Mi Yeon; Kim, Changman; Moon, Jungheun; Heo, Jinhee; Jung, Sokhee P; Kim, Jung Rae

2017-02-28

Polylactic acid (PLA) has been highlighted as an alternative renewable polymer for the replacement of petroleum-based plastic materials, and is considered to be biodegradable. On the other hand, the biodegradation of PLA by terminal degraders, such as microorganisms, requires a lengthy period in the natural environment, and its mechanism is not completely understood. PLA biodegradation studies have been conducted using mainly undefined mixed cultures, but only a few bacterial strains have been isolated and examined. For further characterization of PLA biodegradation, in this study, the PLA-degrading bacteria from digester sludge were isolated and identified using a polymer film-based screening method. The enrichment of sludge on PLA granules was conducted with the serial transference of a subculture into fresh media for 40 days, and the attached biofilm was inoculated on a PLA film on an agar plate. 3D optical microscopy showed that the isolates physically degraded the PLA film due to bacterial degradation. 16S rRNA gene sequencing identified the microbial colonies to be Pseudomonas sp. MYK1 and Bacillus sp. MYK2. The two isolates exhibited significantly higher specific gas production rates from PLA biodegradation compared with that of the initial sludge inoculum.

Effects of Co-Processing Sewage Sludge in the Cement Kiln on PAHs, Heavy Metals Emissions and the Surrounding Environment.

Science.gov (United States)

Lv, Dong; Zhu, Tianle; Liu, Runwei; Li, Xinghua; Zhao, Yuan; Sun, Ye; Wang, Hongmei; Zhang, Fan; Zhao, Qinglin

2018-04-08

To understand the effects of co-processing sewage sludge in the cement kiln on non-criterion pollutants emissions and its surrounding environment, the flue gas from a cement kiln stack, ambient air and soil from the background/downwind sites were collected in the cement plant. Polycyclic aromatic hydrocarbons (PAHs) and heavy metals of the samples were analyzed. The results show that PAHs in flue gas mainly exist in the gas phase and the low molecular weight PAHs are the predominant congener. The co-processing sewage sludge results in the increase in PAHs and heavy metals emissions, especially high molecular weight PAHs and low-volatile heavy metals such as Cd and Pb in the particle phase, while it does not change their compositions and distribution patterns significantly. The concentrations and their distributions of the PAHs and heavy metals between the emissions and ambient air have a positive correlation and the co-processing sewage sludge results in the increase of PAHs and heavy metals concentrations in the ambient air. The PAHs concentration level and their distribution in soil are proportional to those in the particle phase of flue gas, and the co-processing sewage sludge can accelerate the accumulation of the PAHs and heavy metals in the surrounding soil, especially high/middle molecular weight PAHs and low-volatile heavy metals.

Molecular epidemiology of Klebsiella pneumoniae K1 and K2 isolates in Japan.

Science.gov (United States)

Harada, Sohei; Ishii, Yoshikazu; Saga, Tomoo; Aoki, Kotaro; Tateda, Kazuhiro

2018-03-20

Although severe infections caused by hypervirulent Klebsiella pneumoniae isolates, such as K1 isolates belonging to sequence type (ST) 23, have been a significant problem in Asian countries, epidemiology of these isolates in Japan remains unclear. We performed a nationwide molecular epidemiological study of K. pneumoniae K1 and K2 isolates in Japan. Of the 259K. pneumoniae isolates collected, 14 and 16 isolates were identified as capsular genotypes K1 and K2, respectively. All K1 isolates were ST23 or its closely related clones and showed high genetic similarity by pulsed-field gel electrophoresis (PFGE) and the DiversiLab system (DL). K2 isolates, belonging to ST14, ST25, ST65, ST86, and ST110, were more genetically diverse than K1 isolates. Isolates belonging to a specific ST showed identical virulence gene profiles with a few exceptions. PFGE and DL results using K1 and K2 isolates were generally in agreement. Copyright © 2018. Published by Elsevier Inc.

Characterization of the heterotrophic biomass and the endogenous residue of activated sludge.

Science.gov (United States)

Ramdani, Abdellah; Dold, Peter; Gadbois, Alain; Déléris, Stéphane; Houweling, Dwight; Comeau, Yves

2012-03-01

The activated sludge process generates an endogenous residue (X(E)) as a result of heterotrophic biomass decay (X(H)). A literature review yielded limited information on the differences between X(E) and X(H) in terms of chemical composition and content of extracellular polymeric substances (EPS). The objective of this project was to characterize the chemical composition (x, y, z, a, b and c in C(x)H(y)O(z)N(a)P(b)S(c)) of the endogenous and the active fractions and EPS of activated sludge from well designed experiments. To isolate X(H) and X(E) in this study, activated sludge was generated in a 200L pilot-scale aerobic membrane bioreactor (MBR) fed with a soluble and completely biodegradable synthetic influent of sodium acetate as the sole carbon source. This influent, which contained no influent unbiodegradable organic or inorganic particulate matter, allowed the generation of a sludge composed essentially of two fractions: heterotrophic biomass X(H) and an endogenous residue X(E), the nitrifying biomass being negligible. The endogenous decay rate and the active biomass fraction of the MBR sludge were determined in 21-day aerobic digestion batch tests by monitoring the VSS and OUR responses. Fractions of X(H) and X(E) were respectively 68% and 32% in run 1 (MBR at 5.2 day SRT) and 59% and 41% in run 2 (MBR at 10.4 day SRT). The endogenous residue was isolated by subjecting the MBR sludge to prolonged aerobic batch digestion for 3 weeks, and was characterized in terms of (a) elemental analysis for carbon, nitrogen, phosphorus and sulphur; and (b) content of EPS. The MBR sludge was characterized using the same procedures (a and b). Knowing the proportions of X(H) and X(E) in this sludge, it was possible to characterize X(H) by back calculation. Results from this investigation showed that the endogenous residue had a chemical composition different from that of the active biomass with a lower content of inorganic matter (1:4.2), of nitrogen (1:2.9), of phosphorus (1

Date palm and the activated sludge co-composting actinobacteria sanitization potential.

Science.gov (United States)

El Fels, Loubna; Hafidi, Mohamed; Ouhdouch, Yedir

2016-01-01

The objective of this study was to find a connection between the development of the compost actinobacteria and the potential involvement of antagonistic thermophilic actinomycetes in compost sanitization as high temperature additional role. An abundance of actinobacteria and coliforms during the activated sludge and date palm co-composting is determined. Hundred actinomycete isolates were isolated from the sample collected at different composting times. To evaluate the antagonistic effects of the different recovered actinomycete isolates, several wastewater-linked microorganisms known as human and plant potential pathogens were used. The results showed that 12 isolates have an in vitro inhibitory effect on at least 9 of the indicator microorganisms while only 4 active strains inhibit all these pathogens. The antimicrobial activities of sterilized composting time extracts are also investigated.

Molecular characterization of Mycobacterium bovis strains isolated from cattle slaughtered at two abattoirs in Algeria

Directory of Open Access Journals (Sweden)

Ouzrout Rachid

2009-01-01

Full Text Available Abstract Background Bovine Tuberculosis is prevalent in Algeria despite governmental attempts to control the disease. The objective of this study was to conduct, for the first time, molecular characterization of a population sample of Mycobacterium bovis strains isolated from slaughter cattle in Algeria. Between August and November 2007, 7250 animals were consecutively screened at the abattoirs of Algiers and Blida. In 260 animals, gross visible granulomatous lesions were detected and put into culture. Bacterial isolates were subsequently analysed by molecular methods. Results Altogether, 101 bacterial strains from 100 animals were subjected to molecular characterization. M. bovis was isolated from 88 animals. Other bacteria isolated included one strain of M. caprae, four Rhodococcus equi strains, three Non-tuberculous Mycobacteria (NTM and five strains of other bacterial species. The M. bovis strains isolated showed 22 different spoligotype patterns; four of them had not been previously reported. The majority of M. bovis strains (89% showed spoligotype patterns that were previously observed in strains from European cattle. Variable Number of Tandem Repeat (VNTR typing supported a link between M. bovis strains from Algeria and France. One spoligotype pattern has also been shown to be frequent in M. bovis strains from Mali although the VNTR pattern of the Algerian strains differed from the Malian strains. Conclusion M. bovis infections account for a high amount of granulomatous lesions detected in Algerian slaughter cattle during standard meat inspection at Algiers and Blida abattoir. Molecular typing results suggested a link between Algerian and European strains of M. bovis.

Lipid profiling in sewage sludge.

Science.gov (United States)

Zhu, Fenfen; Wu, Xuemin; Zhao, Luyao; Liu, Xiaohui; Qi, Juanjuan; Wang, Xueying; Wang, Jiawei

2017-06-01

High value-added reutilization of sewage sludge from wastewater treatment plants (WWTPs) is essential in sustainable development in WWTPs. However, despite the advantage of high value reutilization, this process must be based on a detailed study of organics in sludge. We used the methods employed in life sciences to determine the profile of lipids (cellular lipids, free fatty acids (FFAs), and wax/gum) in five sludge samples obtained from three typical WWTPs in Beijing; these samples include one sludge sample from a primary sedimentation tank, two activated sludge samples from two Anaerobic-Anoxic-Oxic (A2/O) tanks, and two activated sludge samples from two membrane bioreactor tanks. The percentage of total raw lipids varied from 2.90% to 12.3%. Sludge from the primary sedimentation tank showed the highest concentrations of lipid, FFA, and wax/gum and the second highest concentration of cellular lipids. All activated sludge contained an abundance of cellular lipids (>54%). Cells in sludge can from plants, animals, microbes and so on in wastewater. Approximately 14 species of cellular lipids were identified, including considerable high value-potential ceramide (9567-38774 mg/kg), coenzyme (937-3897 mg/kg), and some phosphatidylcholine (75-548 mg/kg). The presence of those lipid constituents would thus require a wider range of recovery methods for sludge. Both cellular lipids and FFAs contain an abundance of C16-C18 lipids at high saturation level, and they serve as good resources for biodiesel production. Copyright © 2017 Elsevier Ltd. All rights reserved.

Gordonia caeni sp. nov., isolated from sludge of a sewage disposal plant.

Science.gov (United States)

Srinivasan, Sathiyaraj; Park, Giho; Yang, Hyejin; Hwang, Supyong; Bae, Yoonjung; Jung, Yong-An; Kim, Myung Kyum; Lee, Myungjin

2012-11-01

A Gram-stain-positive, strictly aerobic, short-rod-shaped, non-motile strain (designated MJ32(T)) was isolated from a sludge sample of the Daejeon sewage disposal plant in South Korea. A polyphasic approach was applied to study the taxonomic position of strain MJ32(T). Strain MJ32(T) showed highest 16S rRNA gene sequence similarity to Gordonia hirsuta DSM 44140(T) (98.1%) and Gordonia hydrophobica DSM 44015(T) (97.0%); levels of sequence similarity to the type strains of other recognized Gordonia species were less than 97.0%. Phylogenetic analysis based on 16S rRNA gene sequences showed that strain MJ32(T) belonged to the clade formed by members of the genus Gordonia in the family Gordoniaceae. The G+C content of the genomic DNA of strain MJ32(T) was 69.2 mol%. Chemotaxonomically, strain MJ32(T) showed features typical of the genus Gordonia. The predominant respiratory quinone was MK-9(H(2)), the mycolic acids present had C(56)-C(60) carbon atoms, and the major fatty acids were C(16:0) (34.6%), tuberculostearic acid (21.8%), C(16:1)ω7c (19.5%) and C(18:1)ω9c (12.7%). The peptidoglycan type was based on meso-2,6-diaminopimelic acid as the diagnostic diamino acid with glycolated sugars. On the basis of phylogenetic inference, fatty acid profile and other phenotypic properties, strain MJ32(T) is considered to represent a novel species of the genus Gordonia, for which the name Gordonia caeni sp. nov. is proposed. The type strain is MJ32(T) (=KCTC 19771(T)=JCM 16923(T)).

First molecular identification and characterization of classical swine fever virus isolates from Nepal.

Science.gov (United States)

Postel, Alexander; Jha, Vijay C; Schmeiser, Stefanie; Becher, Paul

2013-01-01

Classical swine fever (CSF) is a major constraint to pig production worldwide, and in many developing countries, the epidemiological status is unknown. Here, for the first time, molecular identification and characterization of CSFV isolates from two recent outbreaks in Nepal are presented. Analysis of full-length E2-encoding sequences revealed that these isolates belonged to CSFV subgenotype 2.2 and had highest genetic similarity to isolates from India. Hence, for CSFV, Nepal and India should be regarded as one epidemiological unit. Both Nepalese isolates exhibited significant sequence differences, excluding a direct epidemiological connection and suggesting that CSFV is endemic in that country.

Molecular, ultrastructural, and biological characterization of Pennsylvania isolates of Plum pox virus.

Science.gov (United States)

Schneider, William L; Damsteegt, Vernon D; Gildow, Fred E; Stone, Andrew L; Sherman, Diana J; Levy, Laurene E; Mavrodieva, Vessela; Richwine, Nancy; Welliver, Ruth; Luster, Douglas G

2011-05-01

Plum pox virus (PPV) was identified in Pennsylvania in 1999. The outbreak was limited to a four-county region in southern Pennsylvania. Initial serological and molecular characterization indicated that the isolates in Pennsylvania belong to the D strain of PPV. The Pennsylvania isolates were characterized by sequence analysis, electron microscopy, host range, and vector transmission to determine how these isolates related to their previously studied European counterparts. Genetically, Pennsylvania (PPV-Penn) isolates were more closely related to each other than to any other PPV-D strains, and isolates from the United States, Canada, and Chile were more closely related to each other than to European isolates. The PPV-Penn isolates exist as two clades, suggesting the possibility of multiple introductions. Electron microscopy analysis of PPV-Penn isolates, including cytopathological studies, indicated that the virions were similar to other Potyvirus spp. PPV-Penn isolates had a herbaceous host range similar to that of European D isolates. There were distinct differences in the transmission efficiencies of the two PPV-Penn isolates using Myzus persicae and Aphis spiraecola as vectors; however, both PPV-Penn isolates were transmitted by M. persicae more efficiently than a European D isolate but less efficiently than a European M isolate.

Efficiency of Worm Reactors in Reducing Sludge Volume in Activated Sludge Systems

Directory of Open Access Journals (Sweden)

Azam Naderi

2017-01-01

Full Text Available The activated sludge process is the most widely used on a global scale for the biological treatment of both domestic and industrial effluents. One problem associated with the process, however, is the high volume of sludge produced. Excess sludge treatment and disposal account for up to 60% of the total operating costs of urban wastewater treatment plants due to the stringent environmental regulations on excess sludge disposal. These strict requirements have encouraged a growing interest over the last few years in reducing sludge volumes produced at biological treatment plants and a number of physical, chemical, and mechanical methods have been accordingly developed for this purpose. The proposed methods are disadvantaged due to their rather high investment and operation costs. An alternative technology that avoids many of these limitations is the worm reactor. In this study, the characteristics of this technology are investigated while the related literature is reviewed to derive the optimal conditions for the operation of this process in different situations.

Pythium insidiosum: morphological and molecular identification of Brazilian isolates

Directory of Open Access Journals (Sweden)

Maria Isabel de Azevedo

2012-07-01

Full Text Available Pythium insidiosum is an oomycete belonging to the kingdom Stramenipila and it is the etiologic agent of pythiosis. Pythiosis is a life-threatening infectious disease characterized by the development of chronic lesions on cutaneous and subcutaneous, intestinal, and bone tissues in humans and many species of animals. The identification of P. insidiosum is important in order to implement a rapid and definitive diagnosis and an effective treatment. This study reports the identification of 54 isolates of P. insidiosum of horses, dogs and sheep that presented suspicious clinical lesions of pythiosis from different regions in Brazil, by using morphological and molecular assays. Throughout the PCR it was possible to confirm the identity of all Brazilian isolates as being P. insidiosum.

Molecular epidemiology of group A streptococcus from pharyngeal isolates in Auckland, New Zealand, 2013.

Science.gov (United States)

Williamson, Deborah A; Moreland, Nicole J; Carter, Philip; Upton, Arlo; Morgan, Julie; Proft, Thomas; Lennon, Diana; Baker, Michael G; Dunbar, Rod; Fraser, John D

2014-01-24

To describe the molecular epidemiology of emm types associated with circulating pharyngeal group A streptococcus (GAS) isolates in Auckland, New Zealand. GAS isolates were collected over a 10-day period from a community pathology provider in Auckland. PCR analysis and sequencing of the emm gene was performed at the Institute of Environmental Science and Research. A total of 52 emm types were identified from 278 GAS isolates. The three most common emm types were emm1, emm89 and emm12. Overall, the experimental 30-valent GAS M protein vaccine covered 19 / 52 (37%) of emm types in our study. Our study provides baseline data on the circulating pharyngeal GAS emm types in Auckland. Future clinical and molecular surveillance of GAS pharyngitis is essential in the context of ongoing GAS vaccine development.

Important operational parameters of membrane bioreactor-sludge disintegration (MBR-SD) system for zero excess sludge production.

Science.gov (United States)

Yoon, Seong-Hoon

2003-04-01

In order to prevent excess sludge production during wastewater treatment, a membrane bioreactor-sludge disintegration (MBR-SD) system has been introduced, where the disintegrated sludge is recycled to the bioreactor as a feed solution. In this study, a mathematical model was developed by incorporating a sludge disintegration term into the conventional activated sludge model and the relationships among the operational parameters were investigated. A new definition of F/M ratio for the MBR-SD system was suggested to evaluate the actual organic loading rate. The actual F/M ratio was expected to be much higher than the apparent F/M ratio in MBR-SD. The kinetic parameters concerning the biodegradability of organics hardly affect the system performance. Instead, sludge solubilization ratio (alpha) in the SD process and particulate hydrolysis rate constant (k(h)) in biological reaction determine the sludge disintegration number (SDN), which is related with the overall economics of the MBR-SD system. Under reasonable alpha and k(h) values, SDN would range between 3 and 5 which means the amount of sludge required to be disintegrated would be 3-5 times higher for preventing a particular amount of sludge production. Finally, normalized sludge disintegration rate (q/V) which is needed to maintain a certain level of MLSS in the MBR-SD system was calculated as a function of F/V ratio.

Particle Size (Sieving) and Enthalpy (Acid Calorimetry) Analysis of Single-Pull K East Basin Floor and Pit Sludges

International Nuclear Information System (INIS)

Bredt, P.R.; Delegard, C.H.; Schmidt, A.J.; Silvers, K.L.; Thornton, B.M.; Gano, S.

2000-01-01

This report presents the results of particle size analyses and calorimetry testing performed on selected single-pull sludge samples collected from the Hanford K East Basin between December 1998 and June 1999. The samples were collected as isolated cores predominantly from areas that had not been previously sampled (e.g., North Loadout Pit, Dummy Elevator Pit, Tech View Pit), or from areas in which the sludge composition had been altered since the last sampling (e.g., Weasel Pit). Particle size analyses were performed by washing wet sludge samples through a series of four sieves with openings of 250, 500, 1410, and 4000 microm. The loaded sieves were weighed before and after drying to obtain wet and dry particle size distributions. Knowledge of the particle size distribution is needed to design and predict the performance of the systems that will be used to retrieve, transport, and recover sludge. Also, sieving provides an opportunity to observe the components in the sludge. For example, during sieving of the sludge sample from the North Loadout Pit, significant quantities of organic ion exchange beads were observed. The uranium metal content and the particle size of the uranium metal in the K Basin sludge will largely determine the chemical reactivity of the sludge. In turn, the designs for the sludge handling and storage systems must be compatible with the reactivity of the sludge. Therefore, acid calorimetry was performed to estimate the uranium metal content of the sludge. For this testing, sludge samples were dissolved in nitric acid within a calibrated adiabatic calorimeter. The resulting dissolution enthalpy data were then used to discriminate between metallic uranium (minus3750 J/g in nitric acid) and uranium oxide (minus394 J/g in nitric acid). Results from this testing showed that the single-pull sludge samples contained little or no uranium metal

STUDY ON MAXIMUM SPECIFIC SLUDGE ACIVITY OF DIFFERENT ANAEROBIC GRANULAR SLUDGE BY BATCH TESTS

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

The maximum specific sludge activity of granular sludge from large-scale UASB, IC and Biobed anaerobic reactors were investigated by batch tests. The limitation factors related to maximum specific sludge activity (diffusion, substrate sort, substrate concentration and granular size) were studied. The general principle and procedure for the precise measurement of maximum specific sludge activity were suggested. The potential capacity of loading rate of the IC and Biobed anaerobic reactors were analyzed and compared by use of the batch tests results.

Composting of sewage sludge irradiated

International Nuclear Information System (INIS)

Hashimoto, Shoji; Watanabe, Hiromasa; Nishimura, Koichi; Kawakami, Waichiro

1981-01-01

Recently, the development of the techniques to return sewage sludge to forests and farm lands has been actively made, but it is necessary to assure its hygienic condition lest the sludge is contaminated by pathogenic bacteria. The research to treat sewage sludge by irradiation and utilize it as fertilizer or soil-improving material has been carried out from early on in Europe and America. The effects of the irradiation of sludge are sterilization, to kill parasites and their eggs, the inactivation of weed seeds and the improvement of dehydration. In Japan, agriculture is carried out in the vicinity of cities, therefore it is not realistic to use irradiated sludge for farm lands as it is. The composting treatment of sludge by aerobic fermentation is noticed to eliminate the harms when the sludge is returned to forests and farm lands. It is desirable to treat sludge as quickly as possible from the standpoint of sewage treatment, accordingly, the speed of composting is a problem. The isothermal fermentation experiment on irradiated sludge was carried out using a small-scale fermentation tank and strictly controlling fermentation conditions, and the effects of various factors on the fermentation speed were studied. The experimental setup and method are described. The speed of composting reached the maximum at 50 deg C and at neutral or weak alkaline pH. The speed increased with the increase of irradiation dose up to 30 Mrad. (Kako, I.)

Stabilization/solidification of sewage sludge

Energy Technology Data Exchange (ETDEWEB)

Boura, Panagiota; Katsioti, Margarita; Tsakiridis, Petros; Katsiri, Alexandra

2003-07-01

The main objective of this work is to investigate a viable alternative for the final disposal of sewage sludge from urban wastewater treatment plants by its use as an additive in developing new construction materials. For this purpose, several mixtures of sludge- cement and sludge-cement and jarosite/alunite precipitate were prepared. Jarosite/alunite precipitate is a waste product of a new hydrometallurgical process. Two kinds of sludge were used: primary sludge from Psyttalia Wastewater Treatment Plant, which receives a considerable amount of industrial waste, and biological sludge from Metamorphosi Wastewater Treatment Plant. Various percentages of these sludges were stabilized/solidified with Portland cement and Portland cement with jarosite/alunite. The specimens were tested by determination of compressive strength according to the methods described by European Standard EN 196. X-Ray Diffraction (XRD) analysis as well as Thermogravimetry-Differential Thermal Analysis (TG-DTA) were used to determine the hydration products in 28 days. Furthermore, Toxicity Characteristic Leaching Procedure test for heavy metals (TCLP), were carried out in order to investigate the environmental compatibility of these new materials. (author)

K Basin sludge dissolution engineering study

International Nuclear Information System (INIS)

Westra, A.G.

1998-01-01

The purpose of this engineering study is to investigate the available technology related to dissolution of the K Basin sludge in nitric acid. The conclusion of this study along with laboratory and hot cell tests with actual sludge samples will provide the basis for beginning conceptual design of the sludge dissolver. The K Basin sludge contains uranium oxides, fragments of metallic U, and some U hydride as well as ferric oxyhydroxide, aluminum oxides and hydroxides, windblown sand that infiltrated the basin enclosure, ion exchange resin, and miscellaneous materials. The decision has been made to dispose of this sludge separate from the fuel elements stored in the basins. The sludge will be conditioned so that it meets Tank Waste Remediation System waste acceptance criteria and can be sent to one of the underground storage tanks. Sludge conditioning will be done by dissolving the fuel constituents in nitric acid, separating the insoluble material, adding neutron absorbers for criticality safety, and then reacting the solution with caustic to co-precipitate the uranium and plutonium. There will be five distinct feed streams to the sludge conditioning process two from the K East (KE) Basin and three from the K West (KW) Basin. The composition of the floor and pit sludges which contain more iron oxides and sand than uranium is much different than the canister sludges which are composed of mostly uranium oxides. The sludge conditioning equipment will be designed to process all of the sludge streams, but some of the operating parameters will be adjusted as necessary to handle the different sludge stream compositions. The volume of chemical additions and the amount of undissolved solids will be much different for floor and pit sludge than for canister sludge. Dissolution of uranium metal and uranium dioxide has been studied quite thoroughly and much information is available. Both uranium metal and uranium dioxide have been dissolved on a large scale in nuclear fuel

Microbial degradation of waste hydrocarbons in oily sludge from some Romanian oil fields

International Nuclear Information System (INIS)

Lazar, I.; Dobrota, S.; Voicu, A.; Stefanescu, M.; Sandulescu, L.; Petrisor, I.G.

1999-01-01

During oil production and processing activities, significant quantities of oily sludge are produced. The sludge represents not only an environmental pollution source but also occupies big spaces in storage tanks. Romania, an experienced European oil-producing and processing country, is faced with environmental problems generated by oily sludge accumulations. Many such accumulations are to be submitted to bioremediation processes based on the hydrocarbon degradation activity of naturally occurring, selectively isolated bacteria. In this paper the results concerning a laboratory screening of several natural bacterial consortia and laboratory tests to establish the performance in degradation of hydrocarbons contained in oily sludges from Otesti oil field area, are presented. As a result of the laboratory screening, we selected six natural bacterial consortia (BCSl-I 1 to BCSl-I 6 ) with high ability in degradation of hydrocarbons from paraffinic and non-paraffinic asphaltic oils (between 25.53%-64.30% for non-paraffinic asphaltic oil and between 50.25%-72.97% for paraffinic oil). The laboratory tests proved that microbial degradation of hydrocarbons contained in oily sludge from Otesti oil field area varied from 16.75% to 95.85% in moving conditions (Erlenmeyers of 750 ml on rotary shaker at 200 rpm) and from 16.85% to 51.85% in static conditions (Petri dishes Oe 10 cm or vessels of 500 ml)

Quantitative structure-property relationships for predicting sorption of pharmaceuticals to sewage sludge during waste water treatment processes.

Science.gov (United States)

Berthod, L; Whitley, D C; Roberts, G; Sharpe, A; Greenwood, R; Mills, G A

2017-02-01

Understanding the sorption of pharmaceuticals to sewage sludge during waste water treatment processes is important for understanding their environmental fate and in risk assessments. The degree of sorption is defined by the sludge/water partition coefficient (K d ). Experimental K d values (n=297) for active pharmaceutical ingredients (n=148) in primary and activated sludge were collected from literature. The compounds were classified by their charge at pH7.4 (44 uncharged, 60 positively and 28 negatively charged, and 16 zwitterions). Univariate models relating log K d to log K ow for each charge class showed weak correlations (maximum R 2 =0.51 for positively charged) with no overall correlation for the combined dataset (R 2 =0.04). Weaker correlations were found when relating log K d to log D ow . Three sets of molecular descriptors (Molecular Operating Environment, VolSurf and ParaSurf) encoding a range of physico-chemical properties were used to derive multivariate models using stepwise regression, partial least squares and Bayesian artificial neural networks (ANN). The best predictive performance was obtained with ANN, with R 2 =0.62-0.69 for these descriptors using the complete dataset. Use of more complex Vsurf and ParaSurf descriptors showed little improvement over Molecular Operating Environment descriptors. The most influential descriptors in the ANN models, identified by automatic relevance determination, highlighted the importance of hydrophobicity, charge and molecular shape effects in these sorbate-sorbent interactions. The heterogeneous nature of the different sewage sludges used to measure K d limited the predictability of sorption from physico-chemical properties of the pharmaceuticals alone. Standardization of test materials for the measurement of K d would improve comparability of data from different studies, in the long-term leading to better quality environmental risk assessments. Copyright © 2016 British Geological Survey, NERC. Published by

The effect of operational conditions on the sludge specific methanogenic activity and sludge biodegradability

International Nuclear Information System (INIS)

Leitao, R. C.; Santaella, S. T.; Haandel, A. C. van; Zeeman, G.; Lettinga, G.

2009-01-01

The Specific Methanogenic Activity (SMA) and sludge biodegradability of an anaerobic sludge depends on various operational and environmental conditions imposed to the anaerobic reactor. However, the effects of hydraulic retention time (HRT), influent COD concentration (COD i nf) and sludge retention time (SRT) on those two parameters need to be elucidated. This knowledge about SMA can provide insights about the capacity of the UASB reactors to withstand organic and hydraulic shock loads, whereas the biodegradability gives information necessary for final disposal of the sludge. (Author)

The effect of operational conditions on the sludge specific methanogenic activity and sludge biodegradability

Energy Technology Data Exchange (ETDEWEB)

Leitao, R. C.; Santaella, S. T.; Haandel, A. C. van; Zeeman, G.; Lettinga, G.

2009-07-01

The Specific Methanogenic Activity (SMA) and sludge biodegradability of an anaerobic sludge depends on various operational and environmental conditions imposed to the anaerobic reactor. However, the effects of hydraulic retention time (HRT), influent COD concentration (COD{sub i}nf) and sludge retention time (SRT) on those two parameters need to be elucidated. This knowledge about SMA can provide insights about the capacity of the UASB reactors to withstand organic and hydraulic shock loads, whereas the biodegradability gives information necessary for final disposal of the sludge. (Author)

Molecular identification and characterization of Rhizoctonia solani AG-3 isolates causing black scurf of potato

International Nuclear Information System (INIS)

Zaidy, M.E.; Othman, M.R.; Mahmoud, M.

2018-01-01

Twenty-six isolates of Rhizoctonia solani AG-3 were collected from four potato growing area of Saudi Arabia. Yield damages due to this infection is reported to range from 7-64% (average of 35%), depending on many factors. Molecular identification of R. solani AG-3 isolates by ITS-regions and characterization was done by inter simple sequence repeat (ISSR) markers. Twenty-six isolates of R. solani used in the current study were isolated from potato fields in four major potato-producing regions of Saudi Arabia. All isolates were inoculated on potato and observations on the percentage of disease incidence were recorded. Genomic DNA extraction of R. solani AG-3 isolates was used by A specific and sensitive PCR and ISSR primers. A single splinter of nearly 500 bp was only amplified once genomic DNA from R. solani AG-3 isolates. Amplicon size of three ISSR primers ranged from 0.3 to 2.8 Kb in isolates. Using the three primers, the tested isolates were separated on the basis of genetic similarity coefficients (GSC). The range of the GSC was beginning at 0.62 and ending at 1.00. In unweighted pair-group method arithmetic averages (UPGMA) analysis, the R. solani isolates grouped into five clusters. The present method provided rapid and reliable detection of R. solani AG-3 isolates. Molecular characterization have great genetic variation in the R. solani AG-3 population, without any correlation between aggressiveness, geographical regions and genetic variation based on ISSR markers. (author)

Fermentative hydrogen production by the new marine Pantoea agglomerans isolated from the mangrove sludge

Energy Technology Data Exchange (ETDEWEB)

Zhu, Daling [College of Marine Science and Engineering, Tianjin University of Science and Technology, Tianjin 300457 (China); Wang, Guangce [College of Marine Science and Engineering, Tianjin University of Science and Technology, Tianjin 300457 (China); Institute of Oceanology, Chinese Academy of Sciences, Qingdao 266071 (China); Qiao, Hongjin; Cai, Jinling [Institute of Oceanology, Chinese Academy of Sciences, Qingdao 266071 (China)

2008-11-15

A new fermentative hydrogen-producing bacterium was isolated from mangrove sludge and identified as Pantoea agglomerans using light microscopic examination, biological tests and 16S rRNA gene sequence analysis. The isolated bacterium, designated as P. agglomerans BH-18, is a new strain that has never been optimized as a potential hydrogen-producing bacterium. In this study, the culture conditions and the hydrogen-producing ability of P. agglomerans BH-18 were examined. The strain was a salt-tolerant facultative anaerobe with the initial optimum pH value at 8.0-9.0 and temperature at 30 C on cell growth. During fermentation, hydrogen started to evolve when cell growth entered late-exponential phase and was mainly produced in the stationary phase. The strain was able to produce hydrogen over a wide range of initial pH from 5 to 10, with an optimum initial pH of 6. The level of hydrogen production was affected by the initial glucose concentration, and the optimum value was found to be 10 g glucose/l. The maximum hydrogen-producing yield (2246 ml/l) and overall hydrogen production rate (160 ml/l/h) were obtained at an initial glucose concentration of 10 g/l and an initial pH value of 7.2 in marine culture conditions. In particular, the level of hydrogen production was also affected by the salt concentration. Hydrogen production reached a higher level in fresh culture conditions than in marine ones. In marine conditions, hydrogen productivity was 108 ml/l/h at an initial glucose concentration of 20 g/l and pH value of 7.2, whereas, it increased by 27% in fresh conditions. In addition, this strain could produce hydrogen using glucose and many other carbon sources such as fructose, sucrose, sorbitol and so on. As a result, it is possible that P. agglomerans BH-18 is used for biohydrogen production and biological treatment of mariculture wastewater and marine organic waste. (author)

Electron beam disinfection of sewage sludge

International Nuclear Information System (INIS)

Hashimoto, Shoji

1992-01-01

Electron beam treatment of dehydrated sewage sludge for safe reutilization was performed. Ranges of total bacterial counts and total coliforms in the sludge were from 1.5 x 10 8 to 1.6 x 10 9 and from 2.2 x 10 7 to 1.5 x 10 8 per wet gram, respectively. Total bacterial counts decreased about 5 log cycles after irradiating 5 kGy and irradiation with 2 kGy was enough to kill all coliforms in sewage sludge. The survival curves of total bacteria, obtained by irradiation in oxygen atmosphere, approached to that in nitrogen atmosphere with the increase of sludge thickness. No effects of dose rate and electron energy were found when the sludge layers were thin enough. Continuous disinfection of sewage sludge cake, with the maximum feed rate of 300 kg-sludge/hr, was successfully performed with a Cockcroft-Walton type electron accelerator, a sludge pump and a flat nozzle. (J.P.N.)

Dewatering properties of differently treated sewage sludge

International Nuclear Information System (INIS)

Zehnder, H.J.

1977-01-01

A study on dewatering properties of radiosterilized sewage sludge of different type and origin was carried out. For comparison, also heat-treated (pasteurized) sludge was investigated. The specific filtration resistance of irradiated sewage sludge was lowered in all types of sludge examined. In general, pasteurization increased this parameter. The settling properties of irradiated digested sewage sludge was slightly improved, mainly in the first hours after treatment. Microbial effects may mask the real sedimentation relations especcially in aerobically stabilized sludges. A pasteurization treatment of sewage sludge caused an increased content of soluble substances and suspended particles in the supernatant water. The supernatant water from irradiated sludge showed a smaller increase

Criteria: waste tank isolation and stabilization

Energy Technology Data Exchange (ETDEWEB)

Metz, W.P.; Ogren, W.E.

1976-09-01

The crystallized Hanford high-level wastes stored in single-shell underground tanks consist of sludges and salt cakes covered with supernatural liquor. Purpose of stabilization and isolation is to reduce the releases and losses as a result of a loss of tank integrity. The tanks will be modified so that no inadvertent liquid additions can be made. Criteria for the isolation and stabilization are given and discussed briefly. (DLC)

Criteria: waste tank isolation and stabilization

International Nuclear Information System (INIS)

Metz, W.P.; Ogren, W.E.

1976-09-01

The crystallized Hanford high-level wastes stored in single-shell underground tanks consist of sludges and salt cakes covered with supernatural liquor. Purpose of stabilization and isolation is to reduce the releases and losses as a result of a loss of tank integrity. The tanks will be modified so that no inadvertent liquid additions can be made. Criteria for the isolation and stabilization are given and discussed briefly

Isolation of Cryptococcus gattii molecular type VGIII, from Corymbia ficifolia detritus in Colombia.

Science.gov (United States)

Escandón, P; Sánchez, A; Firacative, C; Castañeda, E

2010-06-01

An environmental sampling survey was carried out in different areas of Bogotá, Colombia, to obtain isolates of members of the Cryptococcus neoformans/C. gattii species complex from Corymbia ficifolia trees. During a 6-month period in 2007, 128 samples consisting of bark, soil around trunk bases, detritus, seeds and flowers were collected from 91 trees and processed according to standard procedures. The molecular type was determined using URA5 restriction fragment length polymorphism (RFLP) analysis and the mating type was established by PCR using specific primers for Mfalpha and Mfa C. gattii was isolated from 15 of the 128 (11.7%) samples, of which three (20%) were recovered from the red flower extract and the remaining 12 from C. ficifolia detritus. URA5 RFLP analysis revealed that all 15 isolates belonged to the molecular type VGIII and mating type specific PCR revealed that all were mating type a. The isolation of C. gattii from C. ficifolia represents an important finding since this is the first report revealing C. ficifolia as a habitat for C. gattii and adds additional information to the ever growing spectrum of tree species from which C. gattii can be recovered.

Composting of gamma-radiation disinfected sewage sludge

International Nuclear Information System (INIS)

Kawakami, W.; Hashimoto, S.; Watanabe, H.; Nishimura, K.; Watanabe, H.; Ito, H.; Takehisa, M.

1981-01-01

The composting of radiation disinfected sewage sludge has been studied since 1978, aiming to present a new process of sludge composting for agricultural uses. This process is composed of two steps: irradiation step to disinfect sludge, and composting step to remove odor and easily decomposable organics in sludge. In this paper, the gamma-irradiation effect on sludge cake and composting condition of irradiated sludge are discussed. (author)

Ultrasonic sludge pretreatment under pressure.

Science.gov (United States)

Le, Ngoc Tuan; Julcour-Lebigue, Carine; Delmas, Henri

2013-09-01

The objective of this work was to optimize the ultrasound (US) pretreatment of sludge. Three types of sewage sludge were examined: mixed, secondary and secondary after partial methanisation ("digested" sludge). Thereby, several main process parameters were varied separately or simultaneously: stirrer speed, total solid content of sludge (TS), thermal operating conditions (adiabatic vs. isothermal), ultrasonic power input (PUS), specific energy input (ES), and for the first time external pressure. This parametric study was mainly performed for the mixed sludge. Five different TS concentrations of sludge (12-36 g/L) were tested for different values of ES (7000-75,000 kJ/kgTS) and 28 g/L was found as the optimum value according to the solubilized chemical oxygen demand in the liquid phase (SCOD). PUS of 75-150 W was investigated under controlled temperature and the "high power input - short duration" procedure was the most effective at a given ES. The temperature increase in adiabatic US application significantly improved SCOD compared to isothermal conditions. With PUS of 150 W, the effect of external pressure was investigated in the range of 1-16 bar under isothermal and adiabatic conditions for two types of sludge: an optimum pressure of about 2 bar was found regardless of temperature conditions and ES values. Under isothermal conditions, the resulting improvement of sludge disintegration efficacy as compared to atmospheric pressure was by 22-67% and 26-37% for mixed and secondary sludge, respectively. Besides, mean particle diameter (D[4,3]) of the three sludge types decreased respectively from 408, 117, and 110 μm to about 94-97, 37-42, and 36-40 μm regardless of sonication conditions, and the size reduction process was much faster than COD extraction. Copyright © 2013 Elsevier B.V. All rights reserved.

Rheological properties of disintegrated sewage sludge

Science.gov (United States)

Wolski, Paweł

2017-11-01

The rheology of the sludge provides information about the capacity and the flow, which in the case of project tasks for the hydraulic conveying installation is an important control parameter. Accurate knowledge of the rheological properties of sludge requires the designation of rheological models. Models single and multiparameter (Ostwald, Bingham, Herschel-Bulkley'a, and others) allow an approximation of flow curves, and the determination of the boundaries of the flow of modified sludge allows you to control the process compaction or are dewatered sludge undergoing flow. The aim of the study was to determine the rheological parameters and rheological models of sludge conditioned by physical methods before and after the process of anaerobic digestion. So far, studies have shown that the application of conditioning in the preparation of sewage sludge increases shear stress, viscosity as well as the limits of flow in relation to the untreated sludge. Offset yield point by the application of a conditioning agent is associated with decreased flowability tested sludge, which has also been observed by analyzing the structure of the prepared samples. Lowering the yield point, and thus the shear stress was recorded as a result of the fermentation test of disintegrated sludge.

Molecular characterization of NDM-1 producing Enterobacteriaceae isolates in Singapore hospitals

Directory of Open Access Journals (Sweden)

Raymond Lin

2012-03-01

Full Text Available Objective: In this study, we molecularly characterized 12 NDM-1 producing clinical Enterobacteriaceae (Klebsiella pneumoniae, Escherichia coli, Enterobacter cloacae isolates that were part of a collection of non-carbapenem susceptible isolates obtained during a one-year period. These isolates were obtained from four local general hospitals in Singapore.Methods: Polymerase chain reaction (PCR assays and sequencing was used to determine the presence of β-lactamase encoding genes (bla including blaNDM-1 and plasmid-mediated quinolone and aminoglycoside resistance determinants. Conjugation experiments were performed to determine the transferability of blaNDM-1. Isolate relatedness was determined by multilocus sequence typing (MLST.Results: The isolates were completely resistant to the second- and third-generation cephalosporins tested as well as carbapenems. Susceptibility profiling of the isolates indicated that 100% retained susceptibility to tigecycline while 11/12 (91.7% were susceptible to colistin. The blaNDM-1 gene was encoded on plasmids that were easily transferable. None of the patients had a travel history to countries where NDM-1 has been reported. The isolates appear clonally unrelated with MLST, revealing a diversity of clonal types among the K. pneumoniae and E. coli isolates.Conclusion: The ease of NDM-1 plasmid transmissibility may help their dissemination among the Enterobacteriaceae. Although it appears that the isolates are clonally unrelated, epidemiological links cannot be fully excluded without further research.

Dewatering of sludges

International Nuclear Information System (INIS)

Bode, P.

1984-01-01

A filter rig has been designed and built. Simulated magnox and alumino ferric hydroxide sludges have been successfully filtered on this equipment and both types of sludge produced a clear filtrate and a cake. The flow rates were low. The cake often partially remained adhered to the filter membrane instead of dropping clear during the filter cleaning cycle. This filtration technique can only be used on sludges which form a non-binding cake. Permeability of the membrane can be altered by stretching. Irradiation of the membrane showed that it should withstand 20 to 50 M.rads. (author)

Rapid Isolation and Molecular Detection of Streptomycin-Producing Streptomycetes

Directory of Open Access Journals (Sweden)

M Motovali-bashi

2006-07-01

Full Text Available Introduction: Streptomyces species are mycelial, aerobic gram-positive bacteria that are isolated from soil and produce a diverse range of antibiotics. Streptomyces griseus produces the antibiotic, streptomycin and forms spores even in a liquid culture. The gene cluster for the production of Streptomycin antibiotic contains strR gene that encodes StrR, a pathway-specific regulator. Then, this pathway-specific regulator induces transcription of other streptomycin production genes in the gene cluster. The overall aim of this work was rapid isolation and molecular detection of streptomycin-producing Streptomycetes, especially S. griseus, from Iranian soils in order to manipulate them for increased production of streptomycin. Methods: This research used new initiative half-specific medium for isolation of Streptomycetes from natural environments, called FZmsn. The fifty colonies of Streptomyces strains grown on the surface of FZmsn medium isolated from environmental samples were defined on the basis of their morphological characteristics and light microscope studies. A set of primers was designed to detect strR by OLIGO software. Results: In colony-PCR reactions followed by gel electrophoresis, 6 colonies from Streptomyces strains colonies were detected as S. griseus colonies. Conclusion: These native Streptomyces strains will be used for genetic manipulation of S. griseus in order to increase production levels of streptomycin.

[Effect of different sludge retention time (SRT) on municipal sewage sludge bioleaching continuous plug flow reaction system].

Science.gov (United States)

Liu, Fen-Wu; Zhou, Li-Xiang; Zhou, Jun; Jiang, Feng; Wang, Dian-Zhan

2012-01-01

A plug-flow bio-reactor of 700 L working volume for sludge bioleaching was used in this study. The reactor was divided into six sections along the direction of the sludge movement. Fourteen days of continuous operation of sludge bioleaching with different sludge retention time (SRT) under the condition of 1.2 m3 x h(-1) aeration amount and 4 g x L(-1) of microbial nutritional substance was conducted. During sludge bioleaching, the dynamic changes of pH, DO, dewaterability (specific resistance to filtration, SRF) of sewage sludge in different sections were investigated in the present study. The results showed that sludge pH were maintained at 5.00, 3.00, 2.90, 2.70, 2.60 and 2.40 from section 1 to section 6 and the SRF of sludge was drastically decreased from initial 0.64 x 10(13) m x kg(-1) to the final 0.33 x 10(13) m x kg(-1) when bioleaching system reached stable at hour 72 with SRT 2.5d. In addition, the sludge pH were maintained at 5.10, 4.10, 3.20, 2.90, 2.70 and 2.60, the DO value were 0.43, 1.47, 3.29, 4.76, 5.75 and 5.88 mg x L(-1) from section 1 to section 6, and the SRF of sludge was drastically decreased from initial 0.56 x 10(13) to the final 0.20 x 10(13) m x kg(-1) when bioleaching system reached stable at hour 120 with SRT 2 d. The pH value was increased to 3.00 at section 6 at hour 48 h with SRT 1.25 d. The bioleaching system imbalanced in this operation conditions because of the utilization efficiency of microbial nutritional substance by Acidibacillus spp. was decreased. The longer sludge retention time, the easier bioleaching system reached stable. 2 d could be used as the optimum sludge retention time in engineering application. The bioleached sludge was collected and dewatered by plate-and-frame filter press to the moisture content of dewatered sludge cake under 60%. This study would provide the necessary data to the engineering application on municipal sewage sludge bioleaching.

Sludge pumping in water treatment

International Nuclear Information System (INIS)

Solar Manuel, M. A.

2010-01-01

In water treatment processes is frequent to separate residual solids, with sludge shape, and minimize its volume in a later management. the technologies to applicate include pumping across pipelines, even to long distance. In wastewater treatment plants (WWTP), the management of these sludges is very important because their characteristics affect load losses calculation. Pumping sludge can modify its behavior and pumping frequency can concern treatment process. This paper explains advantages and disadvantages of different pumps to realize transportation sludge operations. (Author) 11 refs.

Molecular characterization of Cryptococcus neoformans isolated from the environment in Beijing, China.

Science.gov (United States)

Dou, Hongtao; Wang, Huizhu; Xie, Shaowei; Chen, Xinxin; Xu, Zhipeng; Xu, Yingchun

2017-10-01

The molecular type of environmental Cryptococcus neoformans in Beijing was not clear. Our study aims to reveal the molecular characterization of C. neoformans complex from environment in Beijing, China. A total of 435 samples of pigeon droppings from 11 different homes in Beijing were collected from August to November in 2015. Pigeon droppings were inoculated onto caffeic acid cornmeal agar (CACA) to screen C. neoformans complex. Bruker Biotyper matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) was performed for species identification. Serotype and mating type was determined by specific primers. Restriction fragment length polymorphisms of URA5 (URA5-RFLP) were applied to genotype. Multi-locus sequence typing (MLST) was done for further identification and sequence type (ST) determination. Altogether, 81 isolates of C. neoformans AFLP1/VNI were recognized from 435 pigeon droppings in this study. The positive rate for C. neoformans AFLP1/VNI from pigeon droppings in different homes varied from 5.0% to 52.6%, the average was 20.2%. All of these cryptococcal strains were serotype A, MATα. They were genotyped as VNI by URA5-RFLP and were confirmed by MLST. No other molecular types of C. neoformans and Cryptococcus gattii isolates were isolated. Their STs were identified as ST 31 (n = 54, 66.7%), followed by ST 53 (n = 10), ST 191 (n = 8), ST 5 (n = 5), ST 57 (n = 3), and ST 38 (n = 1). We concluded that not only clinical but also environmental isolates of C. neoformans need to be investigated more deeply and more extensively. The virulence difference between ST 5 and ST 31 need to be explored in the future. © The Author 2017. Published by Oxford University Press on behalf of The International Society for Human and Animal Mycology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

RELATIONSHIP BETWEEN SLUDGE DEWATERABILITY NUMBER ...

African Journals Online (AJOL)

A representative of a sludge sample collected from the same source was filtered under the same environmental condition and the result analysed with two different concepts. One method of analysis uses Sludge Dewaterability Number, while the second employed the Carman's Specific resistance concept in sludge ...

Bacterial community analysis of activated sludge: an evaluation of four commonly used DNA extraction methods

NARCIS (Netherlands)

Vanysacker, L.; Declerck, S.A.J.; Hellemans, B.; De Meester, L.; Vankelecom, I.; Declerck, P.

2010-01-01

The effectiveness of three commercially available direct DNA isolation kits (Mobio, Fast, Qiagen) and one published direct DNA extraction protocol (Bead) for extracting bacterial DNA from different types of activated sludge was investigated and mutually compared. The DNA quantity and purity were

Molecular Genetic Analysis of Multi-drug Resistance in Indian Isolates of Mycobacterium tuberculosis

Directory of Open Access Journals (Sweden)

Noman Siddiqi

1998-09-01

Full Text Available A total of 116 isolates from patients attending the out-patient department at the All India Institute of Medical Sciences, New Delhi and the New Delhi Tuberculosis Centre, New Delhi, India were collected. They were analyzed for resistance to drugs prescribed in the treatment for tuberculosis. The drug resistance was initially determined by microbiological techniques. The Bactec 460TB system was employed to determine the type and level of resistance in each isolate. The isolates were further characterized at molecular level. The multi-drug loci corresponding to rpo b, gyr A, kat G were studied for mutation(s by the polymerase chain reaction-single strand conformational polymorphism (PCR-SSCP technique. The SSCP positive samples were sequenced to characterize the mutations in rpo b, and gyr A loci. While previously reported mutations in the gyr A and rpo b loci were found to be present, several novel mutations were also scored in the rpo b locus. Interestingly, analysis of the gyr A locus showed the presence of point mutation(s that could not be detected by PCR-SSCP. Furthermore, rifampicin resistance was found to be an important marker for checking multi-drug resistance (MDR in clinical isolates of Mycobacterium tuberculosis. This is the first report on molecular genetic analysis of MDR tuberculosis one from India, highlights the increasing incidence of MDR in the Indian isolates of M. tuberculosis.

Impact of sludge stabilization processes and sludge origin (urban or hospital) on the mobility of pharmaceutical compounds following sludge landspreading in laboratory soil-column experiments.

Science.gov (United States)

Lachassagne, Delphine; Soubrand, Marilyne; Casellas, Magali; Gonzalez-Ospina, Adriana; Dagot, Christophe

2015-11-01

This study aimed to determine the effect of sludge stabilization treatments (liming and anaerobic digestion) on the mobility of different pharmaceutical compounds in soil amended by landspreading of treated sludge from different sources (urban and hospital). The sorption and desorption potential of the following pharmaceutical compounds: carbamazepine (CBZ), ciprofloxacin (CIP), sulfamethoxazole (SMX), salicylic acid (SAL), ibuprofen (IBU), paracetamol (PAR), diclofenac (DIC), ketoprofen (KTP), econazole (ECZ), atenolol (ATN), and their solid-liquid distribution during sludge treatment (from thickening to stabilization) were investigated in the course of batch testing. The different sludge samples were then landspread at laboratory scale and leached with an artificial rain simulating 1 year of precipitation adapted to the surface area of the soil column used. The quality of the resulting leachate was investigated. Results showed that ibuprofen had the highest desorption potential for limed and digested urban and hospital sludge. Ibuprofen, salicylic acid, diclofenac, and paracetamol were the only compounds found in amended soil leachates. Moreover, the leaching potential of these compounds and therefore the risk of groundwater contamination depend mainly on the origin of the sludge because ibuprofen and diclofenac were present in the leachates of soils amended with urban sludge, whereas paracetamol and salicylic acid were found only in the leachates of soils amended with hospital sludge. Although carbamazepine, ciprofloxacin, sulfamethoxazole, ketoprofen, econazole, and atenolol were detected in some sludge, they were not present in any leachate. This reflects either an accumulation and/or (bio)degradation of these compounds (CBZ, CIP, SMX, KTP, ECZ, and ATN ), thus resulting in very low mobility in soil. Ecotoxicological risk assessment, evaluated by calculating the risk quotients for each studied pharmaceutical compound, revealed no high risk due to the

Occurrence State and Molecular Structure Analysis of Extracellular Proteins with Implications on the Dewaterability of Waste-Activated Sludge.

Science.gov (United States)

Wu, Boran; Ni, Bing-Jie; Horvat, Kristine; Song, Liyan; Chai, Xiaoli; Dai, Xiaohu; Mahajan, Devinder

2017-08-15

The occurrence state and molecular structure of extracellular proteins were analyzed to reveal the influencing factors on the water-holding capacities of protein-like substances in waste-activated sludge (WAS). The gelation process of extracellular proteins verified that advanced oxidation processes (AOPs) for WAS dewaterability improvement eliminated the water affinity of extracellular proteins and prevented these macromolecules from forming stable colloidal aggregates. Isobaric tags for relative and absolute quantitation proteomics identified that most of the extracellular proteins were originally derived from the intracellular part and the proteins originally located in the extracellular part were mainly membrane-associated. The main mechanism of extracellular protein transformation during AOPs could be represented by the damage of the membrane or related external encapsulating structure and the release of intracellular substances. For the selected representative extracellular proteins, the strong correlation (R 2 > 0.97, p proteins on the interstitial water removal from WAS.

Bench-scale enhanced sludge washing and gravity settling of Hanford Tank C-106 Sludge

International Nuclear Information System (INIS)

Brooks, K.P.; Myers, R.L.; Rappe, K.G.

1997-01-01

This report summarizes the results of a bench-scale sludge pretreatment demonstration of the Hanford baseline flowsheet using liter-quantities of sludge from Hanford Site single-shell tank 241-C-106 (tank C-106). The leached and washed sludge from these tests provided Envelope D material for the contractors supporting Tank Waste Remediation System (TWRS) Privatization. Pretreatment of the sludge included enhanced sludge washing and gravity settling tests and providing scale-up data for both these unit operations. Initial and final solids as well as decanted supernatants from each step of the process were analyzed chemically and radiochemically. The results of this work were compared to those of Lumetta et al. (1996a) who performed a similar experiment with 15 grams of C-106, sludge. A summary of the results are shown in Table S.1. Of the major nonradioactive components, those that were significantly removed with enhanced sludge washing included aluminum (31%), chromium (49%), sodium (57%), and phosphorus (35%). Of the radioactive components, a significant amount of 137 Cs (49%) were removed during the enhanced sludge wash. Only a very small fraction of the remaining radionuclides were removed, including 90 Sr (0.4%) and TRU elements (1.5%). These results are consistent with those of the screening test. All of the supernatants (both individually and as a blend) removed from these washing steps, once vitrified as LLW glasses (at 20 wt% Na 2 O), would be less than NRC Class C in TRU elements and less than NRC Class B in 90 Sr

Biodegradation of Unsymmetrical Dimethylhydrazine in Solution and Soil by Bacteria Isolated from Activated Sludge

Directory of Open Access Journals (Sweden)

Qili Liao

2016-03-01

Full Text Available The biodegradation effect and pathway of unsymmetrical dimethylhydrazine (UDMH, which is a major rocket propellant with highly toxic properties, with two strains isolated from the acclimated activated sludge were investigated in solution and in soil. The results demonstrated that Stenotrophomonas sp. M12 (M12 was able to degrade UDMH of 50 mg·L−1 as the sole carbon source in aqueous mineral salt medium (MSM, but could not degrade UDMH in soil. Comamonas sp. P4 (P4 barely degraded UDMH of 50 mg·L−1 as the sole carbon source in aqueous MSM, but the degrading capacity of P4 could be improved by the addition of an extra carbon source. Meanwhile, P4 was able to degrade UDMH of 100–600 mg·kg−1 in the soil. The degradation of UDMH in the soil was influenced by organic matter, autochthonous microorganisms, and metal ions. UDMH could inhibit metabolism of M12 and P4, and the inhibition influence was more severe in aqueous MSM than in soil. Oxygen content was important for M12 biodegrading UDMH, and co-metabolism helped P4 to self-detoxify and self-recover. The main intermediates of UDMH were identified by Gas Chromatography-Mass Spectrometer (GC/MS qualitative analysis, and the concentrations of UDMH and its important transformation products were determined in solution and soil. According to the determination results, the synchronous degradation theory was proposed, and the degradation pathway was discussed.

Settling properties of aerobic granular sludge (AGS) and aerobic granular sludge molasses (AGSM)

Science.gov (United States)

Mat Saad, Azlina; Aini Dahalan, Farrah; Ibrahim, Naimah; Yasina Yusuf, Sara; Aqlima Ahmad, Siti; Khalil, Khalilah Abdul

2018-03-01

Aerobic granulation technology is applied to treat domestic and industrial wastewater. The Aerobic granular sludge (AGS) cultivated has strong properties that appears to be denser and compact in physiological structure compared to the conventional activated sludge. It offers rapid settling for solid:liquid separation in wastewater treatment. Aerobic granules were developed using sequencing batch reactor (SBR) with intermittent aerobic - anaerobic mode with 8 cycles in 24 hr. This study examined the settling velocity performance of cultivated aerobic granular sludge (AGS) and aerobic granular sludge molasses (AGSM). The elemental composition in both AGS and AGSM were determined using X-ray fluorescence (XRF). The results showed that AGSM has higher settling velocity 30.5 m/h compared to AGS.

Electroosmotic dewatering of chalk sludge, iron hydroxide sludge, wet fly ash and biomass

Energy Technology Data Exchange (ETDEWEB)

Hansen, H.K.; Kristensen, I.V.; Ottosen, L.M.; Villumsen, A. [Dept. of Geology and Geotechnical Engineering, The Technical Univ. of Denmark, Lyngby (Denmark)

2001-07-01

Electroosmotic dewatering has been tested in laboratory cells for 4 different porous materials: chalk sludge, iron hydroxide sludge, wet fly ash and biomass sludge from enzyme production. In all cases it was possible to remove water when passing electric DC current through the material. Casagrande's coefficients for the three materials where determined at different water contents. In the electroosmotic experiments shown in this work chalk can be dewatered from 40% to 79% DM (dry matter), fly ash from 75 to 82% DM, iron hydroxide sludge from 2.7 to 19% DM and biomass from 3 to 33% DM. The process was not optimised indicating that higher dry matter contents could be achieved. (orig.)

Enhancing faecal sludge management in peri-urban areas of Lusaka through faecal sludge valorisation: challenges and opportunities

Science.gov (United States)

Tembo, J. M.; Nyirenda, E.; Nyambe, I.

2017-03-01

Lusaka, the capital city of Zambia, has two million inhabitants with 70% residing in peri-urban areas. Ninety (90) % of this population employ pit latrines for excretion generating approximately 22,680 tons of faecal sludge per annum. This sludge is inadequately managed hence of the generated amount, over 60% remains within the residential environment thereby compromising both the environment and public health. To foster a solution to this problem, a study was commissioned to assess faecal sludge valorisation potential and how it would impact on Faecal Sludge Management. The study evaluated policy, institutional and regulatory frameworks, sanitation practices including latrine construction and usage aspects and also characterised the faecal sludge for selected parameters relevant to valorisation. Four peri-urban areas were adopted as study sites. Policy issues together with existing institutional and regulatory frameworks were assessed through literature review. Sanitation practices were evaluated through physical observations, focus group discussions, interviews and questionnaire administration. Faecal sludge characterisation was through sampling and analysis. It was observed that there are policy gaps in fostering faecal sludge valorisation. Sanitation practices and latrines construction also do not favour valorisation. The quality of the raw sludge has potential for valorisation though again, some parameters like solid waste content require drastic changes in sanitation practices in order not to compromise the reuse potential of the sludge. It was concluded that if faecal sludge management is to be enhanced through valorisation, there is need to have policies promoting pit latrine faecal sludge reuse and strengthened regulatory and institutional frameworks in this respect.

Physical and chemical factors affecting sludge consolidation

Energy Technology Data Exchange (ETDEWEB)

Turner, C.W.; Blimkie, M.E.; Lavoie, P.A

1997-09-01

Chemical reactions between sludge components and precipitation reactions within the pores of the existing sludge are shown to contribute to the consolidation of sludge under steam generator operating conditions. Simulations of sludge representative of plants with a mixed iron/copper feedtrain suggest that as the conditions in the feedtrain become more oxidizing the sludge will become harder with a higher nickel ferrite content. The precipitation of feedwater impurities introduced by condenser leaks and of zinc silicate, which is produced in plants with brass condenser tubes and silica in the makeup water, contribute significantly to sludge consolidation. Sodium phosphate is also shown to be an agent of sludge consolidation. (author)

Molecular and phenotypic characterization of endophytic bacteria isolated from sulla nodules.

Science.gov (United States)

Beghalem, Hamida; Aliliche, Khadidja; Chriki, Ali; Landoulsi, Ahmed

2017-10-01

In the current study, bacterial diversity was investigated in root nodules of Sulla pallida and Sulla capitata. The isolates were analyzed on the basis of their phenotypic and molecular characteristics. The phylogenetic analysis based on 16S rRNA and housekeeping genes (recA and atpD) showed that the isolated bacteria related to Sinorhizobium, Neorhizobium, Phyllobacterium, Arthrobacter, Variovorax and Pseudomonas genera. This is the first report of Neorhizobium genus associated with Hedysarum genus. Phenotypically, all strains tolerate the elevated temperature of 40 °C, and salt stress at a concentration of 2%. In addition, the isolates failed to induce nodulation on their original host; and the symbiotic genes could not be amplified, suggesting that these strains are endophytic bacteria. Copyright © 2017 Elsevier Ltd. All rights reserved.

Isolation and molecular identification of yeast strains from “Rabilé” a ...

African Journals Online (AJOL)

Isolation and molecular identification of yeast strains from “Rabilé” a starter of local fermented drink. Ibrahim Keita, Marius K Somda, Aly Savadogo, Iliassou Mogmenga, Ousmane Koita, Alfred S Traore ...

PRNP genetic variability and molecular typing of natural goat scrapie isolates in a high number of infected flocks.

Science.gov (United States)

Fragkiadaki, Eirini G; Vaccari, Gabriele; Ekateriniadou, Loukia V; Agrimi, Umberto; Giadinis, Nektarios D; Chiappini, Barbara; Esposito, Elena; Conte, Michela; Nonno, Romolo

2011-09-30

One hundred and four scrapie positive and 77 negative goats from 34 Greek mixed flocks were analysed by prion protein gene sequencing and 17 caprine scrapie isolates from 11 flocks were submitted to molecular isolate typing. For the first time, the protective S146 variant was reported in Greece, while the protective K222 variant was detected in negative but also in five scrapie positive goats from heavily infected flocks. By immunoblotting six isolates, including two goat flockmates carrying the K222 variant, showed molecular features slightly different from all other Greek and Italian isolates co-analysed, possibly suggesting the presence of different scrapie strains in Greece.

PRNP genetic variability and molecular typing of natural goat scrapie isolates in a high number of infected flocks

Directory of Open Access Journals (Sweden)

Fragkiadaki Eirini G

2011-09-01

Full Text Available Abstract One hundred and four scrapie positive and 77 negative goats from 34 Greek mixed flocks were analysed by prion protein gene sequencing and 17 caprine scrapie isolates from 11 flocks were submitted to molecular isolate typing. For the first time, the protective S146 variant was reported in Greece, while the protective K222 variant was detected in negative but also in five scrapie positive goats from heavily infected flocks. By immunoblotting six isolates, including two goat flockmates carrying the K222 variant, showed molecular features slightly different from all other Greek and Italian isolates co-analysed, possibly suggesting the presence of different scrapie strains in Greece.

Molecular characterization of Acanthamoeba strains isolated from domestic dogs in Tenerife, Canary Islands, Spain.

Science.gov (United States)

Valladares, María; Reyes-Batlle, María; Martín-Navarro, Carmen M; López-Arencibia, Atteneri; Dorta-Gorrín, Alexis; Wagner, Carolina; Martínez-Carretero, Enrique; Piñero, José E; Valladares, Basilio; Lorenzo-Morales, Jacob

2015-06-01

The present study describes two cases of Acanthamoeba infections (keratitis and ascites/peritonitis) in small breed domestic dogs in Tenerife, Canary Islands, Spain. In both cases, amoebic trophozoites were observed under the inverted microscope and isolated from the infected tissues and/or fluids, without detecting the presence of other viral, fungal or bacterial pathogens. Amoebae were isolated using 2 % non-nutrient agar plates and axenified for further biochemical and molecular analyses. Osmotolerance and thermotolerance assays revealed that both isolates were able to grow up to 37 °C and 1 M of mannitol and were thus considered as potentially pathogenic. Moreover, the strains were classified as highly cytotoxic as they cause more than 75 % of toxicity when incubated with two eukaryotic cell lines. In order to classify the strains at the molecular level, the diagnostic fragment 3 (DF3) region of the 18S rDNA of Acanthamoeba was amplified and sequenced, revealing that both isolates belonged to genotype T4. In both cases, owners of the animals did not allow any further studies or follow-up and therefore the current status of these animals is unknown. Furthermore, the isolation of these pathogenic amoebae should raise awareness with the veterinary community locally and worldwide.

Molecular Analysis of Vancomycin-Resistant Enterococci Isolated from Regional Hospitals in Trinidad and Tobago

Directory of Open Access Journals (Sweden)

Patrick E. Akpaka

2016-01-01

Full Text Available Geographic spread of vancomycin-resistant enterococci (VRE clones in cities, countries, or even continents has been identified by molecular techniques. This study aimed at characterizing virulent genes and determining genetic relatedness of 45 VRE isolates from Trinidad and Tobago using molecular tools, including polymerase chain reaction, pulsed-field gel electrophoresis (PFGE, and Random Amplification Polymorphic DNA (RAPD. The majority (84% of the isolates were Enterococcus faecium possessing vanA gene while the rest (16% were Enterococcus faecalis possessing vanB. The esp gene was found in all 45 VRE isolates while hyl genes were found only in E. faecium species. The E. faecium species expressed five distinct PFGE patterns. The predominant clones with similar or common patterns belonged to clones one and three, and each had 11 (29% of the VRE isolates. Plasmid content was identified in representative isolates from each clonal group. By contrast, the E. faecalis species had one PFGE pattern suggesting the presence of an occult and limited clonal spread. The emergence of VRE in the country seems to be related to intra/interhospital dissemination of an epidemic clone carrying the vanA element. Therefore, infection control measures will be warranted to prevent any potential outbreak and spread of VRE in the country.

Bacterial regrowth potential in alkaline sludges from open-sun and covered sludge drying beds

Energy Technology Data Exchange (ETDEWEB)

Alkan, U.; Topac, F.O.; Birden, B.; Baskaya, H.S. [Uludag University, Gorukle (Turkey). Dept. of Environmnetal Engineering

2007-10-15

The aim of this study was to compare the regrowth potentials of wastewater sludges dried in two pilot-scale drying processes namely, Open-Sun Sludge Drying Bed (OSDB) and Covered Sludge Drying Bed (CSDB). Quicklime and/or coal fly ash were added to raw sludge samples prior to drying processes in order to enhance bacterial inactivation. Following three drying cycles (March-April, June-July and August-October), sludge samples were taken from the beds for the regrowth experiments. Addition of alkaline materials prevented the regrowth of faecal coliforms in all rewetted samples except for the samples obtained after the rainfall events in OSDB. Rewetting of these samples in the regrowth experiments increased faecal coliform numbers by 3.5-7 log units. In contradiction, the observed bacterial numbers in rewetted alkaline samples from CSDB were below the EPA Class B criterion (2 million MPN g{center_dot} 1) dry sludge). The combination of additional heat from solar collectors, protection from the rain and the unfavourable living conditions owing to alkaline materials appeared to inactivate bacteria more effectively in CSDB and hence eliminated regrowth potential more efficiently.

Sludge Washing and Demonstration of the DWPF Nitric/Formic Flowsheet in the SRNL Shielded Cells for Sludge Batch 9 Qualification

Energy Technology Data Exchange (ETDEWEB)

Pareizs, J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Newell, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Martino, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Johnson, F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-11-01

Savannah River National Laboratory (SRNL) was requested by Savannah River Remediation (SRR) to qualify the next batch of sludge – Sludge Batch 9 (SB9). Current practice is to prepare sludge batches in Tank 51 by transferring sludge to Tank 51 from other tanks. The sludge is washed and transferred to Tank 40, the current Defense Waste Process Facility (DWPF) feed tank. Prior to sludge transfer from Tank 51 to Tank 40, the Tank 51 sludge must be qualified. SRNL qualifies the sludge in multiple steps. First, a Tank 51 sample is received, then characterized, washed, and again characterized. SRNL then demonstrates the DWPF Chemical Process Cell (CPC) flowsheet with the sludge. The final step of qualification involves chemical durability measurements of glass fabricated in the DWPF CPC demonstrations. In past sludge batches, SRNL had completed the DWPF demonstration with Tank 51 sludge. For SB9, SRNL has been requested to process a blend of Tank 51 and Tank 40 at a targeted ratio of 44% Tank 51 and 56% Tank 40 on an insoluble solids basis.

From municipal/industrial wastewater sludge and FOG to fertilizer: A proposal for economic sustainable sludge management.

Science.gov (United States)

Bratina, Božidar; Šorgo, Andrej; Kramberger, Janez; Ajdnik, Urban; Zemljič, Lidija Fras; Ekart, Janez; Šafarič, Riko

2016-12-01

After a ban on the depositing of untreated sludge in landfills, the sludge from municipal and industrial water-treatment plants can be regarded as a problem. Waste products of the water treatment process can be a problem or an opportunity - a source for obtaining raw materials. In the European Union, raw sludge and fats, oil and grease (FOG) from municipal and industrial wastewater treatment plants (WWTP) cannot be deposited in any natural or controlled environment. For this reason, it must be processed (stabilized, dried) to be used later as a fertilizer, building material, or alternative fuel source suitable for co-incineration in high temperature furnaces (power plants or concrete plants). The processes of drying sludge, where heat and electricity are used, are energy consuming and economically unattractive. Beside energy efficiency, the main problem of sludge drying is in its variability of quality as a raw material. In addition to this, sludge can be contaminated by a number of organic and inorganic pollutants and organisms. Due to the presence or absence of pollutants, different end products can be economically interesting. For example, if the dried sludge contains coliform bacteria, viruses, helminths eggs or smaller quantities of heavy metals, it cannot be used as a fertilizer but can still be used as a fuel. The objectives of the current article is to present a batch-processing pilot device of sludge or digestate that allows the following: (1) low pressure and low temperature energy effective drying of from 10 to 40% remaining water content, (2) disinfection of pathogen (micro)organisms, (3) heavy metal reduction, (4) production of products of predetermined quality (e.g. containing different quantities of water; it can be used as a fertilizer, or if the percentage of water in the dry sludge is decreased to 10%, then the dried sludge can be used as a fuel with a calorific value similar to coal). An important feature is also the utilization of low

The evaporative drying of sludge by immersion in hot oil: Effects of oil type and temperature

Energy Technology Data Exchange (ETDEWEB)

Ohm, Tae-In, E-mail: tiohm1@hanbat.ac.kr [Department of Environmental Engineering, Hanbat National University, San 16-1 Duckmyung-dong, Yusung-gu, Daejeon 305-719 (Korea, Republic of); Chae, Jong-Seong; Lim, Kwang-Soo [Department of Environmental Engineering, Hanbat National University, San 16-1 Duckmyung-dong, Yusung-gu, Daejeon 305-719 (Korea, Republic of); Moon, Seung-Hyun [Waste Energy Research Center, Korea Institute of Energy Research, Jang-dong Yusung-gu, Daejeon 305-343 (Korea, Republic of)

2010-06-15

We investigated the evaporative drying by immersion in hot oil (EDIHO) method for drying sludge. This involved heating oil to a temperature higher than that needed for moisture to be evaporated from the sludge by turbulent heat and mass transfer. We fry-dried sewage and leather plant sludge for 10 min in each of four different oils (waste engine, waste cooking, refined waste, and B-C heavy) and three different temperatures (140 deg. C, 150 deg. C, and 160 deg. C). Drying efficiency was found to be greater for higher temperatures. However, giving consideration to energy efficiency we suggest that the optimal temperature for fry-drying sludge is 150 deg. C. At 150 deg. C, the water content of sewage sludge reduced from 78.9% to between 1.5% (with waste cooking oil) and 3.8% (with waste engine oil). The reduction in water content for leather plant sludge fry-dried at 150 deg. C was from 81.6% to between 1% (with waste cooking oil) and 6.5% (with refined waste oil). The duration of the constant rate-drying period was also influenced by the type of oil used: refined waste oil > waste engine oil > B-C heavy oil > waste cooking oil. The duration at 150 deg. C with waste cooking oil was 3 min for sewage sludge and 2 min for leather plant sludge. It is likely that the drying characteristics of oil are influenced by its thermal properties, including its specific heat, and molecular weight.

The evaporative drying of sludge by immersion in hot oil: Effects of oil type and temperature

International Nuclear Information System (INIS)

Ohm, Tae-In; Chae, Jong-Seong; Lim, Kwang-Soo; Moon, Seung-Hyun

2010-01-01

We investigated the evaporative drying by immersion in hot oil (EDIHO) method for drying sludge. This involved heating oil to a temperature higher than that needed for moisture to be evaporated from the sludge by turbulent heat and mass transfer. We fry-dried sewage and leather plant sludge for 10 min in each of four different oils (waste engine, waste cooking, refined waste, and B-C heavy) and three different temperatures (140 deg. C, 150 deg. C, and 160 deg. C). Drying efficiency was found to be greater for higher temperatures. However, giving consideration to energy efficiency we suggest that the optimal temperature for fry-drying sludge is 150 deg. C. At 150 deg. C, the water content of sewage sludge reduced from 78.9% to between 1.5% (with waste cooking oil) and 3.8% (with waste engine oil). The reduction in water content for leather plant sludge fry-dried at 150 deg. C was from 81.6% to between 1% (with waste cooking oil) and 6.5% (with refined waste oil). The duration of the constant rate-drying period was also influenced by the type of oil used: refined waste oil > waste engine oil > B-C heavy oil > waste cooking oil. The duration at 150 deg. C with waste cooking oil was 3 min for sewage sludge and 2 min for leather plant sludge. It is likely that the drying characteristics of oil are influenced by its thermal properties, including its specific heat, and molecular weight.

Assessing the hydrocarbon degrading potential of indigenous bacteria isolated from crude oil tank bottom sludge and hydrocarbon-contaminated soil of Azzawiya oil refinery, Libya.

Science.gov (United States)

Mansur, Abdulatif A; Adetutu, Eric M; Kadali, Krishna K; Morrison, Paul D; Nurulita, Yuana; Ball, Andrew S

2014-09-01

The disposal of hazardous crude oil tank bottom sludge (COTBS) represents a significant waste management burden for South Mediterranean countries. Currently, the application of biological systems (bioremediation) for the treatment of COTBS is not widely practiced in these countries. Therefore, this study aims to develop the potential for bioremediation in this region through assessment of the abilities of indigenous hydrocarbonoclastic microorganisms from Libyan Hamada COTBS for the biotreatment of Libyan COTBS-contaminated environments. Bacteria were isolated from COTBS, COTBS-contaminated soil, treated COTBS-contaminated soil, and uncontaminated soil using Bushnell Hass medium amended with Hamada crude oil (1 %) as the main carbon source. Overall, 49 bacterial phenotypes were detected, and their individual abilities to degrade Hamada crude and selected COBTS fractions (naphthalene, phenanthrene, eicosane, octadecane and hexane) were evaluated using MT2 Biolog plates. Analyses using average well colour development showed that ~90 % of bacterial isolates were capable of utilizing representative aromatic fractions compared to 51 % utilization of representative aliphatics. Interestingly, more hydrocarbonoclastic isolates were obtained from treated contaminated soils (42.9 %) than from COTBS (26.5 %) or COTBS-contaminated (30.6 %) and control (0 %) soils. Hierarchical cluster analysis (HCA) separated the isolates into two clusters with microorganisms in cluster 2 being 1.7- to 5-fold better at hydrocarbon degradation than those in cluster 1. Cluster 2 isolates belonged to the putative hydrocarbon-degrading genera; Pseudomonas, Bacillus, Arthrobacter and Brevundimonas with 57 % of these isolates being obtained from treated COTBS-contaminated soil. Overall, this study demonstrates that the potential for PAH degradation exists for the bioremediation of Hamada COTBS-contaminated environments in Libya. This represents the first report on the isolation of

Engineered nanoparticles in wastewater and wastewater sludge - Evidence and impacts

International Nuclear Information System (INIS)

Brar, Satinder K.; Verma, Mausam; Tyagi, R.D.; Surampalli, R.Y.

2010-01-01

Nanotechnology has widespread application in agricultural, environmental and industrial sectors ranging from fabrication of molecular assemblies to microbial array chips. Despite the booming application of nanotechnology, there have been serious implications which are coming into light in the recent years within different environmental compartments, namely air, water and soil and its likely impact on the human health. Health and environmental effects of common metals and materials are well-known, however, when the metals and materials take the form of nanoparticles - consequential hazards based on shape and size are yet to be explored. The nanoparticles released from different nanomaterials used in our household and industrial commodities find their way through waste disposal routes into the wastewater treatment facilities and end up in wastewater sludge. Further escape of these nanoparticles into the effluent will contaminate the aquatic and soil environment. Hence, an understanding of the presence, behavior and impact of these nanoparticles in wastewater and wastewater sludge is necessary and timely. Despite the lack of sufficient literature, the present review attempts to link various compartmentalization aspects of the nanoparticles, their physical properties and toxicity in wastewater and wastewater sludge through simile drawn from other environmental streams.

Biological and molecular characterization of Brazilian isolates of Zucchini yellow mosaic virus

Directory of Open Access Journals (Sweden)

David Marques de Almeida Spadotti

2015-02-01

Full Text Available Zucchini yellow mosaic virus (ZYMV causes substantial economic losses in cucurbit crops. Although ZYMV has been present in Brazil for more than 20 years, there is little information about the biological and molecular characteristics of the isolates found in the country. This study aimed to characterize the experimental hosts, pathotypes and genetic diversity of a collection of eleven Brazilian ZYMV isolates within the coat protein gene. For biological analysis, plant species from Amaranthaceae, Chenopodiaceae, Cucurbitaceae, Fabaceae, Solanaceae, and Pedaliaceae were mechanically inoculated and pathotypes were identified based on the reaction of a resistant Cucumis melo, accession PI414723. All of the cucurbit species/varieties and Sesamum indicum were systemically infected with all isolates. The nucleotide sequence variability of the coat protein gene ranged from 82 % to 99 % compared to the corresponding sequences of ZYMV isolates from different geographical locations. No recombination event was detected in the coat protein gene of the isolates.

Molecular epidemiological study of Arctic rabies virus isolates from Greenland and comparison with isolates from throughout the Arctic and Baltic regions

DEFF Research Database (Denmark)

Mansfield, K.L.; Racloz, V.; McElhinney, L.M.

2006-01-01

We report a Molecular epidemiological study of rabies in Arctic Countries by comparing a panel of novel Greenland isolates to a larger cohort of viral sequences from both Arctic and Baltic regions. Rabies Virus isolates originating from wildlife (Arctic/red foxes, raccoon-dogs and reindeer), from...... sequences from the Arctic and Arctic-like viruses, which were distinct from rabies isolates originating ill the Baltic region of Europe, the Steppes in Russia and from North America. The Arctic-like group consist of isolates from India, Pakistan, southeast Siberia and Japan. The Arctic group...... in northeast Siberia and Alaska. Arctic 2b isolates represent a biotype, which is dispersed throughout the Arctic region. The broad distribution of rabies in the Arctic regions including Greenland, Canada and Alaska provides evidence for the movement of rabies across borders....

Degradation of polyvinyl chloride (PVC) / hydrolyzed collagen (HC) blends active sludge test.

Science.gov (United States)

Agafiţei, Gabriela-Elena; Pascu, Mihaela; Cazacu, Georgeta; Vasile, Cornelia

2008-01-01

Biodegradable polymers represent a solution for the environment protection: they decrease the landfill space, by declining the petrochemical sources, and offer also an alternative solution for the recycling. The behavior during degradation in the presence of active sludge of some polyvinyl chloride (PVC) based blends with variable content of hydrolyzed collagen (HC) has been followed. Some samples were subjected to UV irradiation, for 30 hours. The modifications induced in the environment by the polymer systems (pH variation, bacterial composition), as well as the changes of the properties of the blends (weight losses, aspect etc.) were studied. During the first moments of degradation in active sludge, all the samples absorbed water, behavior which favored the biodegradation. The bacteriological analysis of the sludge indicates the presence of some microbiological species. Generally, the populations of microorganisms decrease, excepting the sulphito-reducing anaerobic bacteria, the actinomycetes and other anaerobic bacteria. PVC/HC blends are degraded with a significant rate in active sewage sludge. More susceptible for the degradation are the UV irradiated blends. After the migration of the components with a small molecular mass in the environment, the natural polymer is degraded. The degradation effect increases with the content in the natural polymer.

Relationship between microbial community dynamics and process performance during thermophilic sludge bioleaching.

Science.gov (United States)

Chen, Shen-Yi; Chou, Li-Chieh

2016-08-01

Heavy metals can be removed from the sludge using bioleaching technologies at thermophilic condition, thereby providing an option for biotreatment of wasted sludge generated from wastewater treatment. The purposes of this study were to establish a molecular biology technique, real-time PCR, for the detection and enumeration of the sulfur-oxidizing bacteria during the thermophilic sludge bioleaching. The 16S rRNA gene for real-time PCR quantification targeted the bioleaching bacteria: Sulfobacillus thermosulfidooxidans, Sulfobacillus acidophilus, and Acidithiobacillus caldus. The specificity and stringency for thermophilic sulfur-oxidizing bacteria were tested before the experiments of monitoring the bacterial community, bacterial number during the thermophilic sludge bioleaching and the future application on testing various environmental samples. The results showed that S. acidophilus was identified as the dominant sulfur-oxidizing bacteria, while A. caldus and S. thermosulfidooxidans occurred in relatively low numbers. The total number of the sulfur-oxidizing bacteria increased during the thermophilic bioleaching process. Meanwhile, the decrease of pH, production of sulfate, degradation of SS/VSS, and solubilization of heavy metal were found to correlate well with the population of thermophilic sulfur-oxidizing bacteria during the bioleaching process. The real-time PCR used in this study is a suitable method to monitor numbers of thermophilic sulfur-oxidizing bacteria during the bioleaching process.

Effects of Time, Heat, and Oxygen on K Basin Sludge Agglomeration, Strength, and Solids Volume

Energy Technology Data Exchange (ETDEWEB)

Delegard, Calvin H.; Sinkov, Sergey I.; Schmidt, Andrew J.; Daniel, Richard C.; Burns, Carolyn A.

2011-01-04

Sludge disposition will be managed in two phases under the K Basin Sludge Treatment Project. The first phase is to retrieve the sludge that currently resides in engineered containers in the K West (KW) Basin pool at ~10 to 18°C. The second phase is to retrieve the sludge from interim storage in the sludge transport and storage containers (STSCs) and treat and package it in preparation for eventual shipment to the Waste Isolation Pilot Plant. The work described in this report was conducted to gain insight into how sludge may change during long-term containerized storage in the STSCs. To accelerate potential physical and chemical changes, the tests were performed at temperatures and oxygen partial pressures significantly greater than those expected in the T Plant canyon cells where the STSCs will be stored. Tests were conducted to determine the effects of 50°C oxygenated water exposure on settled quiescent uraninite (UO2) slurry and a full simulant of KW containerized sludge to determine the effects of oxygen and heat on the composition and mechanical properties of sludge. Shear-strength measurements by vane rheometry also were conducted for UO2 slurry, mixtures of UO2 and metaschoepite (UO3•2H2O), and for simulated KW containerized sludge. The results from these tests and related previous tests are compared to determine whether the settled solids in the K Basin sludge materials change in volume because of oxidation of UO2 by dissolved atmospheric oxygen to form metaschoepite. The test results also are compared to determine if heating or other factors alter sludge volumes and to determine the effects of sludge composition and settling times on sludge shear strength. It has been estimated that the sludge volume will increase with time because of a uranium metal → uraninite → metaschoepite oxidation sequence. This increase could increase the number of containers required for storage and increase overall costs of sludge management activities. However, the volume

Effects of Time, Heat, and Oxygen on K Basin Sludge Agglomeration, Strength, and Solids Volume

International Nuclear Information System (INIS)

Delegard, Calvin H.; Sinkov, Sergey I.; Schmidt, Andrew J.; Daniel, Richard C.; Burns, Carolyn A.

2011-01-01

Sludge disposition will be managed in two phases under the K Basin Sludge Treatment Project. The first phase is to retrieve the sludge that currently resides in engineered containers in the K West (KW) Basin pool at ∼10 to 18 C. The second phase is to retrieve the sludge from interim storage in the sludge transport and storage containers (STSCs) and treat and package it in preparation for eventual shipment to the Waste Isolation Pilot Plant. The work described in this report was conducted to gain insight into how sludge may change during long-term containerized storage in the STSCs. To accelerate potential physical and chemical changes, the tests were performed at temperatures and oxygen partial pressures significantly greater than those expected in the T Plant canyon cells where the STSCs will be stored. Tests were conducted to determine the effects of 50 C oxygenated water exposure on settled quiescent uraninite (UO 2 ) slurry and a full simulant of KW containerized sludge to determine the effects of oxygen and heat on the composition and mechanical properties of sludge. Shear-strength measurements by vane rheometry also were conducted for UO 2 slurry, mixtures of UO2 and metaschoepite (UO 3 · 2H 2 O), and for simulated KW containerized sludge. The results from these tests and related previous tests are compared to determine whether the settled solids in the K Basin sludge materials change in volume because of oxidation of UO2 by dissolved atmospheric oxygen to form metaschoepite. The test results also are compared to determine if heating or other factors alter sludge volumes and to determine the effects of sludge composition and settling times on sludge shear strength. It has been estimated that the sludge volume will increase with time because of a uranium metal → uraninite → metaschoepite oxidation sequence. This increase could increase the number of containers required for storage and increase overall costs of sludge management activities. However, the

Sludge Batch 7B Qualification Activities With SRS Tank Farm Sludge

International Nuclear Information System (INIS)

Pareizs, J.; Click, D.; Lambert, D.; Reboul, S.

2011-01-01

Waste Solidification Engineering (WSE) has requested that characterization and a radioactive demonstration of the next batch of sludge slurry - Sludge Batch 7b (SB7b) - be completed in the Shielded Cells Facility of the Savannah River National Laboratory (SRNL) via a Technical Task Request (TTR). This characterization and demonstration, or sludge batch qualification process, is required prior to transfer of the sludge from Tank 51 to the Defense Waste Processing Facility (DWPF) feed tank (Tank 40). The current WSE practice is to prepare sludge batches in Tank 51 by transferring sludge from other tanks. Discharges of nuclear materials from H Canyon are often added to Tank 51 during sludge batch preparation. The sludge is washed and transferred to Tank 40, the current DWPF feed tank. Prior to transfer of Tank 51 to Tank 40, SRNL typically simulates the Tank Farm and DWPF processes with a Tank 51 sample (referred to as the qualification sample). With the tight schedule constraints for SB7b and the potential need for caustic addition to allow for an acceptable glass processing window, the qualification for SB7b was approached differently than past batches. For SB7b, SRNL prepared a Tank 51 and a Tank 40 sample for qualification. SRNL did not receive the qualification sample from Tank 51 nor did it simulate all of the Tank Farm washing and decanting operations. Instead, SRNL prepared a Tank 51 SB7b sample from samples of Tank 7 and Tank 51, along with a wash solution to adjust the supernatant composition to the final SB7b Tank 51 Tank Farm projections. SRNL then prepared a sample to represent SB7b in Tank 40 by combining portions of the SRNL-prepared Tank 51 SB7b sample and a Tank 40 Sludge Batch 7a (SB7a) sample. The blended sample was 71% Tank 40 (SB7a) and 29% Tank 7/Tank 51 on an insoluble solids basis. This sample is referred to as the SB7b Qualification Sample. The blend represented the highest projected Tank 40 heel (as of May 25, 2011), and thus, the highest

Hydrogen production from sewage sludge by steam gasification

Energy Technology Data Exchange (ETDEWEB)

Aye, L.; Klinkajorn, P. [Melbourne Univ. International Technologies Centre, Melbourne, Victoria (Australia). Dept. of Civil and Environmental Engineering

2006-07-01

Because of the shortage of energy sources in the near future, renewable energy, such as biomass, has become an important source of energy. One of the most common approaches for producing gaseous fuels from biomass is gasification. The main product gases of gasification are hydrogen, carbon monoxide, methane and low molecular weight hydrocarbons. Because of the capability of very low emission at the point of use, the interest in using hydrogen for electrical power generation and in electric-vehicles has been increasing. Hydrogen from biomass steam gasification (SG) is a net zero green house gas emission fuel. Sewage sludge (SS) has a potential to produce hydrogen-rich gaseous fuel. Therefore, hydrogen production from sewage sludge may be a solution for cleaner fuel and the sewage sludge disposal problem. This paper presented the results of a computer model for SSSG by using Gibbs free energy minimization (GFEM) method. The computer model developed was used to determine the hydrogen production limits for various steam to biomass ratios. The paper presented an introduction to renewable energy and gasification and discussed the Gibbs free energy minimization method. The study used a RAND algorithm. It presented the computer model input parameters and discussed the results of the stoichiometric analysis and Gibbs free energy minimization. The energy requirement for hydrogen production was also presented. 17 refs., 1 tab., 6 figs.

Molecular epidemiology of Corynebacterium pseudotuberculosis isolated from horses in California.

Science.gov (United States)

Haas, Dionei J; Dorneles, Elaine M S; Spier, Sharon J; Carroll, Scott P; Edman, Judy; Azevedo, Vasco A; Heinemann, Marcos B; Lage, Andrey P

2017-04-01

Corynebacterium pseudotuberculosis biovar Equi is an important pathogen of horses. It is increasing in frequency in the United States, and is responsible for various clinical forms of infection, including external abscesses, internal abscesses of the abdominal or thoracic cavities, and ulcerative lymphangitis. The host/pathogen factors dictating the form or severity of infection are currently unknown. Our recent investigations have shown that genotyping C. pseudotuberculosis isolates using enterobacterial repetitive intergenic consensus (ERIC)-PCR is useful for understanding the evolutionary genetics of the species as well for molecular epidemiology studies. The aims of the present study were to assess (i) the genetic diversity of C. pseudotuberculosis strains isolated from horses in California, United States and (ii) the epidemiologic relationships among isolates. One hundred and seven C. pseudotuberculosis biovar Equi isolates from ninety-five horses, and two C. pseudotuberculosis biovar Ovis strains, C. pseudotuberculosis ATCC 19410 T type strain and C. pseudotuberculosis 1002 vaccine strain, were fingerprinted using the ERIC 1+2-PCR. C. pseudotuberculosis isolated from horses showed a high genetic diversity, clustering in twenty-seven genotypes with a diversity index of 0.91. Minimal spanning tree showed four major clonal complexes with a pattern of temporal clustering. Strains isolated from the same horse showed identical ERIC 1+2-PCR genotype, with the exception of two strains isolated from the same animal that showed distinct genotypes, suggesting a co-infection. We found no strong genetic signals related to clinical form (including internal versus external infections). However, temporal clustering of genotypes was observed. Copyright © 2016. Published by Elsevier B.V.

Environmental sustainability of wastewater sludge treatments

DEFF Research Database (Denmark)

Boyer-Souchet, Florence; Larsen, Henrik Fred

treatment for municipal waste water. A special focus area in Neptune is sludge handling because the sludge amount is expected to increase due to advanced waste water treatment. The main sludge processing methods assessed in Neptune can be divided into two categories: disintegration processes before...... anaerobic digestion (thermal hydrolysis and ultrasound disintegration) and inertisation processes performed at high temperatures (incineration, pyrolysis, gasification, wet oxidation) but they all aim at volume reduction and removal of biodegradable compounds before safe sludge disposal or reuse of its...... resources. As part of a sustainability assessment (or “best practice evaluation”), a comparison between the existing and new sludge handling techniques have been done by use of life cycle assessment (LCA).The concept of induced impacts as compared to avoided impacts when introducing a new sludge treatment...

Adsorption of organic stormwater pollutants onto activated carbon from sewage sludge.

Science.gov (United States)

Björklund, Karin; Li, Loretta Y

2017-07-15

Adsorption filters have the potential to retain suspended pollutants physically, as well as attracting and chemically attaching dissolved compounds onto the adsorbent. This study investigated the adsorption of eight hydrophobic organic compounds (HOCs) frequently detected in stormwater - including four polycyclic aromatic hydrocarbons (PAHs), two phthalates and two alkylphenols - onto activated carbon produced from domestic sewage sludge. Adsorption was studied using batch tests. Kinetic studies indicated that bulk adsorption of HOCs occurred within 10 min. Sludge-based activated carbon (SBAC) was as efficient as tested commercial carbons for adsorbing HOCs; adsorption capacities ranged from 70 to 2800 μg/g (C initial  = 10-300 μg/L; 15 mg SBAC in 150 mL solution; 24 h contact time) for each HOC. In the batch tests, the adsorption capacity was generally negatively correlated to the compounds' hydrophobicity (log K ow ) and positively associated with decreasing molecule size, suggesting that molecular sieving limited adsorption. However, in repeated adsorption tests, where competition between HOCs was more likely to occur, adsorbed pollutant loads exhibited strong positive correlation with log K ow . Sewage sludge as a carbon source for activated carbon has great potential as a sustainable alternative for sludge waste management practices and production of a high-capacity adsorption material. Copyright © 2017 Elsevier Ltd. All rights reserved.

Activated Sludge Rheology

DEFF Research Database (Denmark)

Ratkovich, Nicolas Rios; Horn, Willi; Helmus, Frank

2013-01-01

Rheological behaviour is an important fluid property that severely impacts its flow behaviour and many aspects related to this. In the case of activated sludge, the apparent viscosity has an influence on e.g. pumping, hydrodynamics, mass transfer rates, sludge-water separation (settling and filtr...... rheological measurements. Moreover, the rheological models are not very trustworthy and remain very “black box”. More insight in the physical background needs 30 to be gained. A model-based approach with dedicated experimental data collection is the key to address this.......Rheological behaviour is an important fluid property that severely impacts its flow behaviour and many aspects related to this. In the case of activated sludge, the apparent viscosity has an influence on e.g. pumping, hydrodynamics, mass transfer rates, sludge-water separation (settling......, leading to varying results and conclusions. In this paper, a vast amount of papers are critically reviewed with respect to this and important flaws are highlighted with respect to rheometer choice, rheometer settings and measurement protocol. The obtained rheograms from experimental efforts have...

Ultrasonic sludge disintegration for enhanced methane production in anaerobic digestion: effects of sludge hydrolysis efficiency and hydraulic retention time.

Science.gov (United States)

Kim, Dong-Jin; Lee, Jonghak

2012-01-01

Hydrolysis of waste activated sludge (WAS) has been regarded as the rate limiting step of anaerobic sludge digestion. Therefore, in this study, the effect of ultrasound and hydraulic residence time during sludge hydrolysis was investigated with the goal of enhancing methane production from anaerobic digestion (AD). WAS was ultrasonically disintegrated for hydrolysis, and it was semi-continuously fed to an anaerobic digesters at various hydraulic retention times (HRTs). The results of these experiments showed that the solids and chemical oxygen demand (COD) removal efficiencies when using ultrasonically disintegrated sludge were higher during AD than the control sludge. The longer the HRT, the higher the removal efficiencies of solids and COD, while methane production increased with lower HRT. Sludge with 30% hydrolysis produced 7 × more methane production than the control sludge. The highest methane yields were 0.350 m(3)/kg volatile solids (VS)(add) and 0.301 m(3)/kg COD(con) for 16 and 30% hydrolyzed sludge, respectively. In addition, we found that excess ultrasound irradiation may inhibit AD since the 50% hydrolyzed sludge produced lower methane yields than 16 and 30% hydrolyzed sludge.

Radioactive contamination of sewage sludge

International Nuclear Information System (INIS)

Soeder, C.J.; Zanders, E.; Raphael, T.

1986-01-01

Because of the radioactivity released through the explosion of the nuclear reactor near Chernobyl radionuclides have been accumulated to a significant extent in sewage sludge in the Federal Republic of Germany. This is demonstrated for samples from four activated sludge plants according to a recent recommendation of the German Commission for Radiation Protection, there is until now no reason to deviate from the common practices of sludge disposal or incineration. The degree of radioactive contamination of plant materials produced on farm lands on which sewage sludge is being spread cannot be estimated with sufficient certainty yet. Additional information is required. (orig.) [de

Sewage sludge disposal in Austria

International Nuclear Information System (INIS)

Koch, F.

1997-01-01

Sewage systems serve about 70% of the Austrian population, producing 6 million m 3 of sewage sludge per year with a dry matter content of 4-5%. At present about 52% of this sludge is disposed of in land fills, 33% is incinerated, and only about 15 % is used in agriculture. Although agricultural utilization is becoming increasingly important, several problems, especially those related to public opinion, need to be resolved before increased use will be possible. In this paper, wastewater treatment and sewage-sludge production in Austria, and problems associated with sludge disposal are discussed. (author)

Pathogenicity and molecular analysis of an infectious bursal disease virus isolated from Malaysian village chickens.

Science.gov (United States)

Tan, D Y; Hair-Bejo, M; Omar, A R; Aini, I

2004-01-01

The characteristics of the pathogenic infectious bursal disease virus (IBDV) that infected avian species other than commercial chickens were largely unknown. In this study, by using in vivo and molecular methods, we had characterized an IBDV isolate (named 94268) isolated from an infectious bursal disease (IBD) outbreak in Malaysian village chickens--the adulterated descendant of the Southeast Asian jungle fowl (Gallus bankiva) that were commonly reared in the backyard. The 94268 isolate was grouped as the very virulent IBDV (vvIBDV) strain because it caused severe lesions and a high mortality rate in village chickens (>88%) and experimentally infected specific-pathogen-free chickens (>66%). In addition, it possessed all of the vvIBDV molecular markers in its VP2 gene. Phylogenetic analysis using distance, maximum parsimony, and maximum likelihood methods revealed that 94268 was monophyletic with other vvIBDV isolates and closely related to the Malaysian vvIBDV isolates. Given that the VP2 gene of 94268 isolate was almost identical and evolutionarily closely related to other field IBDV isolates that affected the commercial chickens, we therefore concluded that IBD infections had spread across the farm boundary. IBD infection in the village chicken may represent an important part of the IBD epidemiology because these birds could harbor the vvIBDV strain and should not be overlooked in the control and prevention of the disease.

Sewage sludges disinfection

International Nuclear Information System (INIS)

Alexandre, D.

1977-01-01

There is an hygienic risk in using biological sewage sludges for agriculture. Systematic analysis carried out on sludges samples obtained from purification plants in East and South part of France, show the almost uniform presence of pathogenic microorganisms. Some of it survive more than 9 months after soil application. Conventional process for disinfection: liming and heat are not suitable for agricultural use. On the other hand, irradiation involves no modification in structure and composition of sludges. Radiation doses required for disinfection vary according to microorganisms. If some of them are eliminated with rather light doses (200 krad) mycobacteria, viruses and eggs of worms resist to more important doses. Security dose is estimated around 1000 krad

Development of Sulfidogenic Sludge from Marine Sediments and Trichloroethylene Reduction in an Upflow Anaerobic Sludge Blanket Reactor.

Science.gov (United States)

Guerrero-Barajas, Claudia; Ordaz, Alberto; García-Solares, Selene Montserrat; Garibay-Orijel, Claudio; Bastida-González, Fernando; Zárate-Segura, Paola Berenice

2015-10-15

The importance of microbial sulfate reduction relies on the various applications that it offers in environmental biotechnology. Engineered sulfate reduction is used in industrial wastewater treatment to remove large concentrations of sulfate along with the chemical oxygen demand (COD) and heavy metals. The most common approach to the process is with anaerobic bioreactors in which sulfidogenic sludge is obtained through adaptation of predominantly methanogenic granular sludge to sulfidogenesis. This process may take a long time and does not always eliminate the competition for substrate due to the presence of methanogens in the sludge. In this work, we propose a novel approach to obtain sulfidogenic sludge in which hydrothermal vents sediments are the original source of microorganisms. The microbial community developed in the presence of sulfate and volatile fatty acids is wide enough to sustain sulfate reduction over a long period of time without exhibiting inhibition due to sulfide. This protocol describes the procedure to generate the sludge from the sediments in an upflow anaerobic sludge blanket (UASB) type of reactor. Furthermore, the protocol presents the procedure to demonstrate the capability of the sludge to remove by reductive dechlorination a model of a highly toxic organic pollutant such as trichloroethylene (TCE). The protocol is divided in three stages: (1) the formation of the sludge and the determination of its sulfate reducing activity in the UASB, (2) the experiment to remove the TCE by the sludge, and (3) the identification of microorganisms in the sludge after the TCE reduction. Although in this case the sediments were taken from a site located in Mexico, the generation of a sulfidogenic sludge by using this procedure may work if a different source of sediments is taken since marine sediments are a natural pool of microorganisms that may be enriched in sulfate reducing bacteria.

Development of Sulfidogenic Sludge from Marine Sediments and Trichloroethylene Reduction in an Upflow Anaerobic Sludge Blanket Reactor

Science.gov (United States)

Guerrero-Barajas, Claudia; Ordaz, Alberto; García-Solares, Selene Montserrat; Garibay-Orijel, Claudio; Bastida-González, Fernando; Zárate-Segura, Paola Berenice

2015-01-01

The importance of microbial sulfate reduction relies on the various applications that it offers in environmental biotechnology. Engineered sulfate reduction is used in industrial wastewater treatment to remove large concentrations of sulfate along with the chemical oxygen demand (COD) and heavy metals. The most common approach to the process is with anaerobic bioreactors in which sulfidogenic sludge is obtained through adaptation of predominantly methanogenic granular sludge to sulfidogenesis. This process may take a long time and does not always eliminate the competition for substrate due to the presence of methanogens in the sludge. In this work, we propose a novel approach to obtain sulfidogenic sludge in which hydrothermal vents sediments are the original source of microorganisms. The microbial community developed in the presence of sulfate and volatile fatty acids is wide enough to sustain sulfate reduction over a long period of time without exhibiting inhibition due to sulfide. This protocol describes the procedure to generate the sludge from the sediments in an upflow anaerobic sludge blanket (UASB) type of reactor. Furthermore, the protocol presents the procedure to demonstrate the capability of the sludge to remove by reductive dechlorination a model of a highly toxic organic pollutant such as trichloroethylene (TCE). The protocol is divided in three stages: (1) the formation of the sludge and the determination of its sulfate reducing activity in the UASB, (2) the experiment to remove the TCE by the sludge, and (3) the identification of microorganisms in the sludge after the TCE reduction. Although in this case the sediments were taken from a site located in Mexico, the generation of a sulfidogenic sludge by using this procedure may work if a different source of sediments is taken since marine sediments are a natural pool of microorganisms that may be enriched in sulfate reducing bacteria. PMID:26555802

40 CFR Appendix A to Part 503 - Procedure To Determine the Annual Whole Sludge Application Rate for a Sewage Sludge

Science.gov (United States)

2010-07-01

... Whole Sludge Application Rate for a Sewage Sludge A Appendix A to Part 503 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SEWAGE SLUDGE STANDARDS FOR THE USE OR DISPOSAL OF SEWAGE SLUDGE Pt... a Sewage Sludge Section 503.13(a)(4)(ii) requires that the product of the concentration for each...

Molecular characterization of Streptococcus agalactiae and Streptococcus uberis isolates from bovine milk.

Science.gov (United States)

Shome, Bibek Ranjan; Bhuvana, Mani; Mitra, Susweta Das; Krithiga, Natesan; Shome, Rajeswari; Velu, Dhanikachalam; Banerjee, Apala; Barbuddhe, Sukhadeo B; Prabhudas, Krishnamshetty; Rahman, Habibar

2012-12-01

Streptococci are one among the major mastitis pathogens which have a considerable impact on cow health, milk quality, and productivity. The aim of the present study was to investigate the occurrence and virulence characteristics of streptococci from bovine milk and to assess the molecular epidemiology and population structure of the Indian isolates using multilocus sequence typing (MLST) and pulsed-field gel electrophoresis (PFGE). Out of a total of 209 bovine composite milk samples screened from four herds (A-D), 30 Streptococcus spp. were isolated from 29 milk samples. Among the 30 isolates, species-specific PCR and partial 16S rRNA gene sequence analysis identified 17 Streptococcus agalactiae arising from herd A and 13 Streptococcus uberis comprising of 5, 7, and 1 isolates from herds B, C, and D respectively. PCR based screening for virulence genes revealed the presence of the cfb and the pavA genes in 17 and 1 S. agalactiae isolates, respectively. Similarly, in S. uberis isolates, cfu gene was present in six isolates from herd C, the pau A/skc gene in all the isolates from herds B, C, and D, whereas the sua gene was present in four isolates from herd B and the only isolate from herd D. On MLST analysis, all the S. agalactiae isolates were found to be of a novel sequence type (ST), ST-483, reported for the first time and is a single locus variant of the predicted subgroup founder ST-310, while the S. uberis isolates were found to be of three novel sequence types, namely ST-439, ST-474, and ST-475, all reported for the first time. ST-474 was a double locus variant of three different STs of global clonal complex ST-143 considered to be associated with clinical and subclinical mastitis, but ST-439 and ST-475 were singletons. Unique sequence types identified for both S. agalactiae and S. uberis were found to be herd specific. On PFGE analysis, identical or closely related restriction patterns for S. agalactiae ST-483 and S. uberis ST-439 in herds A and B

The fate of a nitrobenzene-degrading bacterium in pharmaceutical wastewater treatment sludge.

Science.gov (United States)

Ren, Yuan; Yang, Juan; Chen, Shaoyi

2015-12-01

This paper describes the fate of a nitrobenzene-degrading bacterium, Klebsiella oxytoca NBA-1, which was isolated from a pharmaceutical wastewater treatment facility. The 90-day survivability of strain NBA-1 after exposure to sludge under anaerobic and aerobic conditions was investigated. The bacterium was inoculated into sludge amended with glucose and p-chloronitrobenzene (p-CNB) to compare the bacterial community variations between the modified sludge and nitrobenzene amendment. The results showed that glucose had no obvious effect on nitrobenzene biodegradation in the co-metabolism process, regardless of the presence/absence of oxygen. When p-CNB was added under anaerobic conditions, the biodegradation rate of nitrobenzene remained unchanged although p-CNB inhibited the production of aniline. The diversity of the microbial community increased and NBA-1 continued to be one of the dominant strains. Under aerobic conditions, the degradation rate of both nitrobenzene and p-CNB was only 20% of that under anaerobic conditions. p-CNB had a toxic effect on the microorganisms in the sludge so that most of the DGGE (denaturing gradient gel electrophoresis) bands, including that of NBA-1, began to disappear under aerobic conditions after 90days of exposure. These data show that the bacterial community was stable under anaerobic conditions and the microorganisms, including NBA-1, were more resistant to the adverse environment. Copyright © 2015 Elsevier Ltd. All rights reserved.

PBDEs in Italian sewage sludge and environmental risk of using sewage sludge for land application

International Nuclear Information System (INIS)

Cincinelli, Alessandra; Martellini, Tania; Misuri, Lorenza; Lanciotti, Eudes; Sweetman, Andy; Laschi, Serena; Palchetti, Ilaria

2012-01-01

Polybrominated diphenyl ethers (PBDEs) were determined in sewage sludge samples collected from eight Italian wastewater treatment plants (WWTPs) between June 2009 and March 2010. Total PBDE concentrations ranged from 158.3 to 9427 ng g −1 dw, while deca-BDE (BDE-209) (concentrations ranging from 130.6 to 9411 ng g −1 dw) dominated the congener profile in all the samples, contributing between 77% and 99.8% of total PBDE. The suitability of using a magnetic particle enzyme-linked immunoassay (ELISA) to analyse PBDEs in sewage sludge was also tested. The ELISA results, expressed as BDE-47 equivalents, were well correlated with those obtained by GC–NCI–MS, with correlation coefficients (r 2 ) of 0.899 and 0.959, depending on the extraction procedure adopted. The risk assessment of PBDEs in sewage sludge addressed to land application was calculated. PEC soil values compared to the relative PNEC soil for penta and deca-BDE suggests that there is a low risk to the soil environment. - Highlights: ► PBDEs in sewage sludge were determined in eight Italian WWTPs for the first time. ► PBDEs concentrations showed differences between the eight investigated WWTPs. ► Deca-BDE (BDE-209) was the dominant congener in all samples. ► The suitability of using ELISA method to analyse PBDEs in sewage sludge was tested. ► The risk assessment of using sewage sludge for land application was evaluated. - Determination of PBDEs in sewage sludge by GC–NCI–MS and ELISA test and risk assessment when sewage sludge is used for land application.

Agricultural yields of irradiated sewage sludge

International Nuclear Information System (INIS)

Magnavacca, Cecilia; Miranda, E.; Sanchez, M.

1999-01-01

Lettuce, radish and ryegrass have been used to study the nitrogen fertilization of soil by sewage sludge. The results show that the irradiated sludge improve by 15 - 30 % the production yield, compared to the non-irradiated sludge. (author)

Sustainability of Domestic Sewage Sludge Disposal

Directory of Open Access Journals (Sweden)

Claudia Bruna Rizzardini

2014-04-01

Full Text Available Activated sludge is now one of the most widely used biological processes for the treatment of wastewaters from medium to large populations. It produces high amounts of sewage sludge that can be managed and perceived in two main ways: as a waste it is discharged in landfill, as a fertilizer it is disposed in agriculture with direct application to soil or subjected to anaerobic digestion and composting. Other solutions, such as incineration or production of concrete, bricks and asphalt play a secondary role in terms of their degree of diffusion. The agronomical value of domestic sewage sludge is a proved question, which may be hidden by the presence of several pollutants such as heavy metals, organic compounds and pathogens. In this way, the sustainability of sewage sludge agricultural disposal requires a value judgment based on knowledge and evaluation of the level of pollution of both sewage sludge and soil. The article analyzed a typical Italian case study, a water management system of small communities, applying the criteria of evaluation of the last official document of European Union about sewage sludge land application, the “Working Document on Sludge (3rd draft, 2000”. The report brought out good sewage sludge from small wastewater treatment plants and soils quality suggesting a sustainable application.

Tracking down antibiotic-resistant Pseudomonas aeruginosa isolates in a wastewater network.

Directory of Open Access Journals (Sweden)

Céline Slekovec

Full Text Available The Pseudomonas aeruginosa-containing wastewater released by hospitals is treated by wastewater treatment plants (WWTPs, generating sludge, which is used as a fertilizer, and effluent, which is discharged into rivers. We evaluated the risk of dissemination of antibiotic-resistant P. aeruginosa (AR-PA from the hospital to the environment via the wastewater network. Over a 10-week period, we sampled weekly 11 points (hospital and urban wastewater, untreated and treated water, sludge of the wastewater network and the river upstream and downstream of the WWTP of a city in eastern France. We quantified the P. aeruginosa load by colony counting. We determined the susceptibility to 16 antibiotics of 225 isolates, which we sorted into three categories (wild-type, antibiotic-resistant and multidrug-resistant. Extended-spectrum β-lactamases (ESBLs and metallo-β-lactamases (MBLs were identified by gene sequencing. All non-wild-type isolates (n = 56 and a similar number of wild-type isolates (n = 54 were genotyped by pulsed-field gel electrophoresis and multilocus sequence typing. Almost all the samples (105/110, 95.5% contained P. aeruginosa, with high loads in hospital wastewater and sludge (≥3×10(6 CFU/l or/kg. Most of the multidrug-resistant isolates belonged to ST235, CC111 and ST395. They were found in hospital wastewater and some produced ESBLs such as PER-1 and MBLs such as IMP-29. The WWTP greatly reduced P. aeruginosa counts in effluent, but the P. aeruginosa load in the river was nonetheless higher downstream than upstream from the WWTP. We conclude that the antibiotic-resistant P. aeruginosa released by hospitals is found in the water downstream from the WWTP and in sludge, constituting a potential risk of environmental contamination.

Molecular identification of fungi isolated from bean tissues with anthracnose symptoms

International Nuclear Information System (INIS)

Vanegas Berrouet, Katherin M; Gutierrez Sanchez, Pablo A; Marin Montoya, Mauricio A

2014-01-01

In this work, endophytic fungi from leaves and pods of bean presenting anthracnose symptoms were isolated from plants collected at different municipalities in the province of Antioquia (Colombia). Isolates were identified by sequencing the RDNA its regions together with the examination of reproductive structures during sporulation in culture media. Colletotrichum lindemuthianum, the causal agent of anthracnose was isolated in all samples showing symptoms of this disease. These results were confirmed by duplex PCR using the specific primers CD1/CD2 and CY1/CY2. Additionally, 17 endophytic fungi were obtained. Fourteen isolates did not sporulate in culture media (Mycelia sterilia) but were identified by phylogenetic analysis of the regions as the Ascomycetes: Leptosphaerulina (3), Diaporthe (3), Gibberella (1), Plectosphaerella (1) and Biscogniauxia (1) and the Mitosporic genera phoma (2), Alternaria (2) and Stemphylium (1) Three isolates were identified combining morphological and molecular analysis as Fusarium (2) and Curvularia lunata (1). This work increases our knowledge of the mycobiota of legume plants and will serve as support of future studies aimed at determining the effect of these fungi on the development of anthracnose as well as other problems affecting the bean crop.

Virological investigations on inadiated sewage sludge

International Nuclear Information System (INIS)

Epp, C.

1980-08-01

The virusinactivating activity of a Co 60 -irradiation pilot plant at Geiselbullach/Munich was to be examined. We investigated 16 impure sewage water, 15 purified sewage water, 32 raw sladge samples, 62 digested sludge samples before irradiation, 52 digested sludge samples after irradiation and 9 raw sludge samples after irradiation. We completed these investigations by adding poliovaccinevirus type 1 to the digested sludge before irradiation and by adding suspensions of pure virus in MEM + 2% FBS packed in synthetic capsules and mixtures of virus and sludge packed in synthetic capsules to the digested sludge. After the irradiation we collected the capsules and determined the virustiter. The testviruses were poliovaccinevirus type 1, poliowildvirus type 1, echovirus type 6, coxsackie-B-virus type 5, coxsackie-A-virus type 9 and adenovirus type 1. In the field trial the irradiation results were like the laboratory results assuming that the sewage sludge was homogenized enough by digestion and the solid particle concentration was not more than 3%. The D-value was 300-400 krad for enteroviruses and 700 krad for adenovirus. (orig.) [de

A review on sludge dewatering indices.

Science.gov (United States)

To, Vu Hien Phuong; Nguyen, Tien Vinh; Vigneswaran, Saravanamuth; Ngo, Huu Hao

2016-01-01

Dewatering of sludge from sewage treatment plants is proving to be a significant challenge due to the large amounts of residual sludges generated annually. In recent years, research and development have focused on improving the dewatering process in order to reduce subsequent costs of sludge management and transport. To achieve this goal, it is necessary to establish reliable indices that reflect the efficiency of sludge dewatering. However, the evaluation of sludge dewaterability is not an easy task due to the highly complex nature of sewage sludge and variations in solid-liquid separation methods. Most traditional dewatering indices fail to predict the maximum cake solids content achievable during full-scale dewatering. This paper reviews the difficulties in assessing sludge dewatering performance, and the main techniques used to evaluate dewatering performance are compared and discussed in detail. Finally, the paper suggests a new dewatering index, namely the modified centrifugal index, which is demonstrated to be an appropriate indicator for estimating the final cake solids content as well as simulating the prototype dewatering process.

Enhancement of sludge reduction and methane production by removing extracellular polymeric substances from waste activated sludge.

Science.gov (United States)

Nguyen, Minh Tuan; Mohd Yasin, Nazlina Haiza; Miyazaki, Toshiki; Maeda, Toshinari

2014-12-01

The management of waste activated sludge (WAS) recycling is a concern that affects the development of the future low-carbon society, particularly sludge reduction and biomass utilization. In this study, we investigated the effect of removing extracellular polymeric substances (EPS), which play important roles in the adhesion and flocculation of WAS, on increased sludge disintegration, thereby enhancing sludge reduction and methane production by anaerobic digestion. EPS removal from WAS by ethylenediaminetetraacetic acid (EDTA) significantly enhanced sludge reduction, i.e., 49 ± 5% compared with 27 ± 1% of the control at the end the digestion process. Methane production was also improved in WAS without EPS by 8881 ± 109 CH4 μmol g(-1) dry-weight of sludge. Microbial activity was determined by denaturing gradient gel electrophoresis and real-time polymerase chain reaction, which showed that the hydrolysis and acetogenesis stages were enhanced by pretreatment with 2% EDTA, with a larger methanogenic community and better methane production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Comparison and analysis of membrane fouling between flocculent sludge membrane bioreactor and granular sludge membrane bioreactor.

Directory of Open Access Journals (Sweden)

Wang Jing-Feng

Full Text Available The goal of this study is to investigate the effect of inoculating granules on reducing membrane fouling. In order to evaluate the differences in performance between flocculent sludge and aerobic granular sludge in membrane reactors (MBRs, two reactors were run in parallel and various parameters related to membrane fouling were measured. The results indicated that specific resistance to the fouling layer was five times greater than that of mixed liquor sludge in the granular MBR. The floc sludge more easily formed a compact layer on the membrane surface, and increased membrane resistance. Specifically, the floc sludge had a higher moisture content, extracellular polymeric substances concentration, and negative surface charge. In contrast, aerobic granules could improve structural integrity and strength, which contributed to the preferable permeate performance. Therefore, inoculating aerobic granules in a MBR presents an effective method of reducing the membrane fouling associated with floc sludge the perspective of from the morphological characteristics of microbial aggregates.

Modeling Aspects Of Activated Sludge Processes Part I: Process Modeling Of Activated Sludge Facilitation And Sedimentation

International Nuclear Information System (INIS)

Ibrahim, H. I.; EI-Ahwany, A.H.; Ibrahim, G.

2004-01-01

Process modeling of activated sludge flocculation and sedimentation reviews consider the activated sludge floc characteristics such as: morphology viable and non-viable cell ratio density and water content, bio flocculation and its kinetics were studied considering the characteristics of bio flocculation and explaining theory of Divalent Cation Bridging which describes the major role of cations in bio flocculation. Activated sludge flocculation process modeling was studied considering mass transfer limitations from Clifft and Andrew, 1981, Benefild and Molz 1983 passing Henze 1987, until Tyagi 1996 and G. Ibrahim et aI. 2002. Models of aggregation and breakage of flocs were studied by Spicer and Pratsinis 1996,and Biggs 2002 Size distribution of floes influences mass transfer and biomass separation in the activated sludge process. Therefore, it is of primary importance to establish the role of specific process operation factors, such as sludge loading dynamic sludge age and dissolved oxygen, on this distribution with special emphasis on the formation of primary particles

Isolation and molecular characterization of Cryptococcus species isolated from pigeon nests and Eucalyptus trees.

Science.gov (United States)

Kamari, A; Sepahvand, A; Mohammadi, R

2017-06-01

Cryptococcus species are pathogenic and non-pathogenic basidiomycete yeasts that are found widely in the environment. Based on phenotypic methods, this genus has many species; however, its taxonomy is presently being re-evaluated by modern techniques. The Cryptococcus species complex includes two sibling taxa of Cryptococcus neoformans and Cryptococcus gattii . We aimed to investigate the possible distribution of Cryptococcus species in pigeon nests and Eucalyptus trees in Ilam, Iran, using molecular techniques. Two hundred and seventy-four specimens were collected from pigeon nests and Eucalyptus trees during 2016-2017. All the specimens were sub-cultured on Sabouraud Glucose Agar with chloramphenicol and bird seed agar. For molecular identification, the ITS15.8SITS2 rDNA region was amplified using the first and fourth internal transcribed spacer (ITS1 and ITS4, respectively) primers. The purified products were applied for cycle sequencing reactions in forward direction with ITS1 primer. The obtained results were analyzed with Chromas 2.3. Thirty-three out of 186 cultures (17.7%) and 11 out of 88 cultures (12.5%) were positive among pigeon nest and Eucalyptus tree specimens, respectively. Cryptococcus albidus (17.2%), C. albidus var. kuetzingii (3.4%), C. adeliensis (3.4%), C. uzbekistanensis (3.4%), and C. neoformans var. grubii (3.4%) were isolated from pigeon nests, and Cryptococcus adeliensis (25%) was the only Cryptococcus species isolated from Eucalyptus trees. The presence of pigeons and Eucalyptus trees in the vicinity of some particular places such as rest homes and hospitals should be considered as a risk factor for the immunocompromised population.

The molecular structure of the insoluble organic matter isolated from Murchison carbonaceous chondrite.

Science.gov (United States)

Robert, F.; Derenne, S.

2009-04-01

During these last 10 years, our group has characterized the various molecular moieties of the insoluble organic matter (IOM) isolated from carbonaceous meteorites with the aim of reconstructing its overall molecular structure. Indeed, a precise knowledge of the structure of an organic macromolecule contains irreplaceable information that traces its mechanisms of synthesis and its conditions of formation. Such a modelled structure will be presented. Carbonaceous chondrites contain up to 3 wt % of carbon that is under the form of soluble and insoluble fractions. The IOM, which constitutes more than 75 wt% of the bulk organic matter, was isolated from the bulk rock through successive acid dissolutions. The chemical structure of the isolated IOM has been studied by both (1) destructive and (2) non destructive methods. Methods include thermal and chemical degradations followed by GC/MS, spectroscopic techniques (nuclear magnetic resonance, Fourier transform infra red spectroscopy; X-ray absorption near-edge spectroscopy, electron paramagnetic resonance) along with high resolution transmission electron microscopy. Although each technique alone cannot provide definite information on the chemical structure of such a complex material, the combination of the results can be used to reconstruct the molecular structure of the IOM. The proposed structure accounts for all these measured parameters. The details of this structure reveal information of the conditions of its formation in space and allow to discuss the mechanisms of organo-synthesis in the cosmochemical context of the formation of the solar system.

Molecular Characterization of Streptococcus agalactiae Isolated from Bovine Mastitis in Eastern China

Science.gov (United States)

Yang, Yongchun; Liu, Yinglong; Ding, Yunlei; Yi, Li; Ma, Zhe; Fan, Hongjie; Lu, Chengping

2013-01-01

One hundred and two Streptococcus agalactiae (group B streptococcus [GBS]) isolates were collected from dairy cattle with subclinical mastitis in Eastern China during 2011. Clonal groups were established by multilocus sequence typing (MLST) and pulsed-field gel electrophoresis (PFGE), respectively. Capsular polysaccharides (CPS), pilus and alpha-like-protein (Alp) family genes were also characterized by molecular techniques. MLST analysis revealed that these isolates were limited to three clonal groups and were clustered in six different lineages, i.e. ST (sequence type) 103, ST568, ST67, ST301, ST313 and ST570, of which ST568 and ST570 were new genotypes. PFGE analysis revealed this isolates were clustered in 27 PFGE types, of which, types 7, 8, 14, 15, 16, 18, 23 and 25 were the eight major types, comprising close to 70% (71/102) of all the isolates. The most prevalent sequence types were ST103 (58% isolates) and ST568 (31% isolates), comprising capsular genotype Ia isolates without any of the detected Alp genes, suggesting the appearance of novel genomic backgrounds of prevalent strains of bovine S. agalactiae. All the strains possessed the pilus island 2b (PI-2b) gene and the prevalent capsular genotypes were types Ia (89% isolates) and II (11% isolates), the conserved pilus type providing suitable data for the development of vaccines against mastitis caused by S. agalactiae. PMID:23874442

Methyl tert-Butyl Ether (MTBE) - Its Movement and Fate in the Environment and Potential for Natural Attenuation

Science.gov (United States)

1999-10-01

but at varying rates, by indigenous microbiota . Normal alkanes of low molecular weight (C-8 to C-22) are metabolized most rapidly, followed by...confirmed that TBA degradation occurred at a rate slower than MTBE degradation. Pure bacterial cultures isolated from activated sludge and the fruit of...isolated from activated sludge and fruit of the Gingko tree. They have been classified as belonging to the genuses Methlobacterium, Rhodococcus, and

Impact of sludge retention time on sludge characteristics and microbial community in MBR.

Science.gov (United States)

Su, Yuchun; Pan, Jill Ruhsing; Huang, Chihpin; Chang, Chialing

2011-01-01

In this study, the impact of sludge retention time (SRT) on sludge characteristics and microbial community and the effect on membrane fouling in membrane bioreactor (MBR) was investigated. The results show that MBR with longer SRT has less fouling propensity, in agreement with other studies, despite the fact that the MBR with longer SRT contained higher MLSS and smaller particle size. However, much more soluble microbial products (SMPs) were released in MBR with shorter SRT. More slime on the membrane surface was observed in MBR with shorter SRT while sludge cakes formed on the membrane surface in MBR with longer SRT. The results show that SMP contributes to the severe fouling observed in MBR with shorter SRT, which is in agreement with other studies showing that SMPs were the major foulants in MBR. Under different SRTs of operation, the bacterial community structures of the sludge obtained by use of polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) were almost identical, but those on the membrane surface differed substantially. It suggests that, although SRT has impact on sludge characteristics, it doesn't affect the microbial community in the suspension.

REDUCTION OF EXCESS SLUDGE PRODUCTION IN AN ACTIVATED SLUDGE SYSTEM BASED ON LYSIS-CRYPTIC GROWTH, UNCOUPLING METABOLISM AND FOLIC ACID ADDITION

Directory of Open Access Journals (Sweden)

V. F. Velho

Full Text Available Abstract The following sludge reduction alternatives were tested in wastewater biological reactors: oxic-settling-anaerobic (OSA-process; ultrasonic disintegration (UD; chlorination (CH; 3,3',4',5-tetrachlorosalicylanilide (TCS; and folic acid (FA. Compared to the control system, UD reduced 55% of the sludge production, and greater substrate and nutrient removal efficiency was achieved. CH worsened the sludge settleability and increased the SVI values; the system achieved 25% of sludge reduction. OSA showed 50% and 60% of sludge reduction after 16 and 10 hours under anaerobic conditions, respectively. The observed sludge yield during TCS addition was decreased by 40%, and the sludge settleability worsened. FA presented the highest sludge reduction (75%, and the system improved the nutrient removal efficiency by 30% compared to the control system and maintained the sludge properties. Acute toxicity conducted with Daphnia magna classified the effluent from the sludge reduction systems as non-toxic for discharge into water sources.

Hexavalent chromium removal using aerobic activated sludge batch ...

African Journals Online (AJOL)

The following Cr(VI) removal systems were tested: activated sludge alone; activated sludge with an external electron donor (5 g/. of lactose); activated sludge with PAC addition (4 g/.); activated sludge with both PAC and lactose; and PAC alone. The results reported here showed that activated sludges are capable of ...

Molecular characterization of Histoplasma capsulatum isolated from an outbreak in treasure hunters Histoplasma capsulatum in treasure hunters

Directory of Open Access Journals (Sweden)

Muñoz Bertha

2010-09-01

Full Text Available Abstract Background In Mexico, primary pulmonary histoplasmosis is the most relevant clinical form of the disease. The geographical distribution of specific strains of Histoplasma capsulatum circulating in Mexico has not been fully established. Outbreaks must be reported in order to have current, updated information on this disease, identifying new endemic areas, manner of exposure to the fungi, and molecular characterization of the causative agents. We report a recent outbreak of histoplasmosis in treasure hunters and the molecular characterization of two isolates obtained from these patients. Methods Six patients admitted to the National Institute of Respiratory Diseases (INER in Mexico City presented severe respiratory symptoms suggestive of histoplasmosis. They acquired the infection in the Veracruz (VZ endemic zone. Diagnosis was made by X-ray and Computed tomography (CT, liver function, immunological techniques, and culture. Identification of H. capsulatum isolates was confirmed by using Polymerase chain reaction (PCR was conducted with a probe from the M antigen, and the isolates were characterized by means of Random amplification of polymorphic DNA (RAPD-PCR employed the 1253 oligonucleotide and a mixture of oligonucleotides 1281 and 1283. These were compared to eight reference strain isolates from neighboring areas. Results X-ray and CT revealed disseminated micronodular images throughout lung parenchyma, as well as bilateral retrocaval, prevascular, subcarinal, and hilar adenopathies, hepatosplenomegaly, and altered liver function tests. Five of the six patients developed disseminated histoplasmosis. Two H. capsulatum strains were isolated. The same band profile was detected in both strains, indicating that both isolates corresponded to the sole H. capsulatum strain. Molecular characterization of the isolates was similar in 100% with the EH-53 Hidalgo human (HG strain (reference strain integrated into the LAm A clade described for

First-order hydrothermal oxidation kinetics of digested sludge compared with raw sludge.

Science.gov (United States)

Shanableh, A; Imteaz, M

2008-09-01

This article presents an assessment of the first-order hydrothermal oxidation kinetics of a selected digested sludge at subcritical ( 374 degrees C) temperatures in the range of 250-460 degrees C. Furthermore, the results were compared with reported oxidation kinetics of raw sludge treated under identical experimental conditions. In the assessment, oxidation was considered to proceed in two steps: (1) decomposition of the particulate, or non-filterable, chemical oxygen demand (PCOD); followed by (2) ultimate oxidation and removal of the total, particulate and soluble, COD. The accumulation and removal of soluble COD (SCOD) was determined from the difference between the rates of sludge decomposition and ultimate oxidation. Using results from batch and continuous-flow hydrothermal treatment experiments, the reacting organic ingredients were separated into groups according to the ease or difficulty at which they were decomposed or removed, with Arrhenius-type activation energy levels assigned to the different groups. The analysis confirmed that within the treatment range of 75% to more than 97% COD removal, the oxidation kinetics of the digested and raw sludges were nearly identical despite differences in the proportions of their original organic ingredients. The original organic ingredients were mostly removed above 75% COD removal, and the oxidation kinetics appeared to be dominated by the removal of acetic acid, an intermediate by-product which constituted 50% to more than 80% of the remaining COD. Furthermore, the oxidation kinetics of both sludge types were consistent with reported first-order oxidation kinetics of pure acetic acid solutions. The resulting kinetic models adequately represented hydrothermal oxidation of digested sludge, in terms of COD and PCOD removals, as well as accumulation and removal of the soluble SCOD.

Electrodialytic removal of cadmium from wastewater sludge

DEFF Research Database (Denmark)

Jakobsen, M. R.; Fritt-Rasmussen, Janne; Nielsen, S.

2004-01-01

This paper presents for the first time laboratory results demonstrating electrodialytic removal of Cd from wastewater sludge, which is a method originally developed for soil remediation. During the remediation a stirred suspension of wastewater sludge was exposed to an electric dc field. The liquid....../solid (ml/g fresh sludge) ratio was between 1.4 and 2. Three experiments were performed where the sludge was suspended in distilled water, citric acid or HNO"3. The experimental conditions were otherwise identical. The Cd removal in the three experiments was 69, 70 and 67%, respectively, thus the removal...... was approximately the same. Chemical extraction experiments with acidic solutions showed that 5-10 times more Cd could be extracted from decomposed sludge than from fresh sludge. It is likely that the mobilization of Cd during decomposition of the sludge contributes to the efficient removal of Cd...

Test Plan: Sludge Treatment Project Corrosion Process Chemistry Follow-on Testing

Energy Technology Data Exchange (ETDEWEB)

Delegard, Calvin H.; Schmidt, Andrew J.; Poloski, Adam P.

2007-08-17

This test plan was prepared by the Pacific Northwest National Laboratory (PNNL) under contract with Fluor Hanford (FH). The test plan describes the scope and conditions to be used to perform laboratory-scale testing of the Sludge Treatment Project (STP) hydrothermal treatment of K Basin sludge. The STP, managed for the U. S. Department of Energy (DOE) by FH, was created to design and operate a process to eliminate uranium metal from the sludge prior to packaging for Waste Isolation Pilot Plant (WIPP) by using high temperature liquid water to accelerate the reaction, produce uranium dioxide from the uranium metal, and safely discharge the hydrogen. The proposed testing builds on the approach and laboratory test findings for both K Basin sludge and simulated sludge garnered during prior testing from September 2006 to March 2007. The outlined testing in this plan is designed to yield further understanding of the nature of the chemical reactions, the effects of compositional and process variations and the effectiveness of various strategies to mitigate the observed high shear strength phenomenon observed during the prior testing. These tests are designed to provide process validation and refinement vs. process development and design input. The expected outcome is to establish a level of understanding of the chemistry such that successful operating strategies and parameters can be implemented within the confines of the existing STP corrosion vessel design. In July 2007, the DOE provided direction to FH regarding significant changes to the scope of the overall STP. As a result of the changes, FH directed PNNL to stop work on most of the planned activities covered in this test plan. Therefore, it is unlikely the testing described here will be performed. However, to preserve the test strategy and details developed to date, the test plan has been published.

Molecular characterization of dengue viruses isolated from patients in Central Java, Indonesia.

Science.gov (United States)

Kusmintarsih, Endang S; Hayati, Rahma F; Turnip, Oktaviani N; Yohan, Benediktus; Suryaningsih, Suhestri; Pratiknyo, Hery; Denis, Dionisius; Sasmono, R Tedjo

2017-10-19

Dengue is hyper-endemic in Indonesia. Purwokerto city in Central Java province is routinely ravaged by the disease. Despite the endemicity of dengue in this city, there is still no data on the virological aspects of dengue in the city. We conducted a molecular surveillance study of the circulating dengue viruses (DENV) in Purwokerto city to gain information on the virus origin, serotype and genotype distribution, and phylogenetic characteristics of DENV. A cross-sectional dengue molecular surveillance study was conducted in Purwokerto. Sera were collected from dengue-suspected patients attending three hospitals in the city. Diagnosis was performed using dengue NS1 antigen and IgG/IgM antibodies detection. DENV serotyping was performed using Simplexa Dengue real-time RT-PCR. Sequencing was conducted to obtain full-length DENV Envelope (E) gene sequences, which were then used in phylogenetic and genotypic analyses. Patients' clinical and demographic data were collected and analyzed. A total of 105 dengue-suspected patients' sera were collected, in which 80 (76.2%) were positive for IgM and/or IgG, and 57 (54.2%) were confirmed as dengue by NS1 antigen and/or DENV RNA detection using RT-PCR. Serotyping was successful for 47 isolates. All four serotypes circulated in the area with DENV-3 as the predominant serotype. Phylogenetic analyses grouped the isolates into Genotype I for DENV-1, Cosmopolitan genotype for DENV-2, and Genotype I and II for DENV-3 and -4, respectively. The analyses also revealed the close relatedness of Purwokerto isolates to other DENV strains from Indonesia and neighboring countries. We reveal the molecular and virological characteristics of DENV in Purwokerto, Banyumas regency, Central Java. The genotype and phylogenetic analyses indicate the endemicity of the circulating DENV in the city. Our serotype and genotype data provide references for future dengue molecular epidemiology studies and disease management in the region. Copyright © 2017 The

Respirometry in activated sludge

NARCIS (Netherlands)

Spanjers, H.

1993-01-01

The purpose of the study was (1) to develop a respiration meter capable of continuously measuring, using different procedures, the oxygen uptake rate of activated sludge and (2) to expand knowledge about respiration related characteristics of wastewater and activated sludge.

A

Isolation, enumeration, molecular identification and probiotic potential evaluation of lactic acid bacteria isolated from sheep milk

OpenAIRE

Acurcio, L.B.; Souza, M.R.; Nunes, A.C.; Oliveira, D.L.S.; Sandes, S.H.C.; Alvim, L.B.

2014-01-01

Lactic acid bacteria species were molecularly identified in milk from Lacaune, Santa Inês and crossbred sheep breeds and their in vitro probiotic potential was evaluated. The species identified were Enterococcus faecium (56.25%), E. durans (31.25%) and E. casseliflavus (12.5%). No other lactic acid bacteria species, such as lactobacilli, was identified. Most of the isolated enterococci were resistant to gastric pH (2.0) and to 0.3% oxgall. All tested enterococci were resistant to ceftazidime,...

Sustainable sludge management in developing countries

Energy Technology Data Exchange (ETDEWEB)

Jimenez, B.; Barrios, J.A.; Mendez, J.M.; Diaz, J.

2003-07-01

Worldwide, unsanitary conditions are responsible of more than three million deaths annually. One of the reasons is the low level of sanitation in developing countries. Particularly, sludge from these regions has a high parasite concentration and low heavy metal content even though the available information is limited. Different issues needed to achieve a sustainable sludge management in developing nations are analysed. Based on this analysis some conclusions arise: sludge management plays an important role in sanitation programs by helping reduce health problems and associated risks; investments in sanitation should consider sludge management within the overall projects; the main restriction for reusing sludge is the high microbial concentration, which requires a science-based decision of the treatment process, while heavy metals are generally low; the adequate sludge management needs the commitment of those sectors involved in the development and enforcement of the regulations as well as those that are directly related to its generation, treatment, reuse or disposal; current regulations have followed different approaches, based mainly on local conditions, but they favour sludge reuse to fight problems like soil degradation, reduced crop production, and the increased use of inorganic fertilizers. This paper summarises an overview of theses issues. (author)

Pressurized Fluidized Bed Combustion of Sewage Sludge

Science.gov (United States)

Suzuki, Yoshizo; Nojima, Tomoyuki; Kakuta, Akihiko; Moritomi, Hiroshi

A conceptual design of an energy recovering system from sewage sludge was proposed. This system consists of a pressurized fluidized bed combustor, a gas turbine, and a heat exchanger for preheating of combustion air. Thermal efficiency was estimated roughly as 10-25%. In order to know the combustion characteristics of the sewage sludge under the elevated pressure condition, combustion tests of the dry and wet sewage sludge were carried out by using laboratory scale pressurized fluidized bed combustors. Combustibility of the sewage sludge was good enough and almost complete combustion was achieved in the combustion of the actual wet sludge. CO emission and NOx emission were marvelously low especially during the combustion of wet sewage sludge regardless of high volatile and nitrogen content of the sewage sludge. However, nitrous oxide (N2O) emission was very high. Hence, almost all nitrogen oxides were emitted as the form of N2O. From these combustion tests, we judged combustion of the sewage sludge with the pressurized fluidized bed combustor is suitable, and the conceptual design of the power generation system is available.

Molecular Epidemiology Reveals Genetic Diversity amongst Isolates of the Cryptococcus neoformans/C. gattii Species Complex in Thailand

Science.gov (United States)

Kaocharoen, Sirada; Ngamskulrungroj, Popchai; Firacative, Carolina; Trilles, Luciana; Piyabongkarn, Dumrongdej; Banlunara, Wijit; Poonwan, Natteewan; Chaiprasert, Angkana; Meyer, Wieland; Chindamporn, Ariya

2013-01-01

To gain a more detailed picture of cryptococcosis in Thailand, a retrospective study of 498 C. neoformans and C. gattii isolates has been conducted. Among these, 386, 83 and 29 strains were from clinical, environmental and veterinary sources, respectively. A total of 485 C. neoformans and 13 C. gattii strains were studied. The majority of the strains (68.9%) were isolated from males (mean age of 37.97 years), 88.5% of C. neoformans and only 37.5% of C. gattii strains were from HIV patients. URA5-RFLP and/or M13 PCR-fingerprinting analysis revealed that the majority of the isolates were C. neoformans molecular type VNI regardless of their sources (94.8%; 94.6% of the clinical, 98.8% of the environmental and 86.2% of the veterinary isolates). In addition, the molecular types VNII (2.4%; 66.7% of the clinical and 33.3% of the veterinary isolates), VNIV (0.2%; 100% environmental isolate), VGI (0.2%; 100% clinical isolate) and VGII (2.4%; 100% clinical isolates) were found less frequently. Multilocus Sequence Type (MLST) analysis using the ISHAM consensus MLST scheme for the C. neoformans/C. gattii species complex identified a total of 20 sequence types (ST) in Thailand combining current and previous data. The Thai isolates are an integrated part of the global cryptococcal population genetic structure, with ST30 for C. gattii and ST82, ST83, ST137, ST141, ST172 and ST173 for C. neoformans being unique to Thailand. Most of the C. gattii isolates were ST7 = VGIIb, which is identical to the less virulent minor Vancouver island outbreak genotype, indicating Thailand as a stepping stone in the global spread of this outbreak strain. The current study revealed a greater genetic diversity and a wider range of major molecular types being present amongst Thai cryptococcal isolates than previously reported. PMID:23861989

Hydrogen Evolution and Sludge Suspension During the Preparation of the First Batch of Sludge at the Savannah River Site

International Nuclear Information System (INIS)

Hay, M.S.; Lee, E.D.

1995-01-01

The first batch of High Level Radioactive Sludge for the Defense Waste Processing Facility is being prepared in two 4.9 million liter waste tanks. The preparation involves removing water soluble salts by washing (water addition, sludge suspension, settling and decantation). Sludge suspension is accomplished using long shafted slurry pumps that are mounted on rotating turntables. During the sludge suspension runs in 1993 and 1994, the slurry pumps' cleaning radius was determined to be less than that expected from previous determinations using synthetic sludge in a full size waste tank mockup. Hydrogen concentrations in the tanks' vapor space were monitored during the sludge suspension activities. As expected, the initial agitation of the sludge increased the hydrogen concentration, however, with the controls in place the hydrogen concentration was maintained below seven percent of the lower flammability limit

Development of a test method to access the sludge reduction potential of aquatic organisms in activated sludge

NARCIS (Netherlands)

Buijs, B.R.; Klapwijk, A.; Elissen, H.J.H.; Rulkens, W.H.

2008-01-01

This article shows the development of a quantitative sludge reduction test method, which uses the sludge consuming aquatic worm Lumbriculus variegatus (Oligochaeta, Lumbriculidae). Essential for the test are sufficient oxygen supply and the presence of a non-stirred layer of sludge for burrowing of

Nocardioides daejeonensis sp. nov., a denitrifying bacterium isolated from sludge in a sewage-disposal plant.

Science.gov (United States)

Woo, Sung-Geun; Srinivasan, Sathiyaraj; Yang, Jihoon; Jung, Yong-An; Kim, Myung Kyum; Lee, Myungjin

2012-05-01

Strain MJ31(T), a gram-reaction-positive, aerobic, rod-shaped, non-motile bacterium, was isolated from a sludge sample collected at the Daejeon sewage-disposal plant, in South Korea, and characterized in order to determine its taxonomic position. Phylogenetic analysis based on 16S rRNA gene sequences indicated that strain MJ31(T) belonged to the genus Nocardioides, appearing most closely related to Nocardioides dubius KSL-104(T) (98.6 % sequence similarity), Nocardioides jensenii DSM 20641(T) (97.6 %), Nocardioides daedukensis MDN22(T) (97.2 %) and Nocardioides mesophilus MSL-22(T) (97.0 %). The chemotaxonomic properties of strain MJ31(T) were consistent with those of the genus Nocardioides: MK-8(H(4)) was the predominant menaquinone, iso-C(16 : 0), iso-C(17 : 0) and C(18 : 1)ω9c were the predominant cellular fatty acids, and the cell-wall peptidoglycan was based on LL-2,6-diaminopimelic acid. The genomic DNA G+C content of strain MJ31(T) was 71.2 mol%. Some differential phenotypic properties and low DNA-DNA relatedness values (<28 %) with the type strains of closely related species indicated that strain MJ31(T) represents a novel species, for which the name Nocardioides daejeonensis sp. nov. is proposed. The type strain is MJ31(T) ( = KCTC 19772(T) = JCM 16922(T)).

Sewage sludge as a biomass energy source

Directory of Open Access Journals (Sweden)

Pavel Kolat

2013-01-01

Full Text Available The major part of the dry matter content of sewage sludge consists of nontoxic organic compounds, in general a combination of primary sludge and secondary microbiological sludge. The sludge also contains a substantive amount of inorganic material and a small amount of toxic components. There are many sludge-management options in which production of energy is one of the key treatment steps. The most important options are anaerobic digestion, co-digestion, incineration in combination with energy recovery and co-incineration in coal-fired power plants. The goal of our applied research is to verify, if the sludge from waste water treatment plants may be used as a biomass energy source in respect of the EU legislation, which would comply with emission limits or the proposal of energy process optimizing the preparation of coal/sludge mixture for combustion in the existing fluid bed boilers in the Czech Republic. The paper discusses the questions of thermal usage of mechanically drained stabilized sewage sludge from the waste water treatment plants in the boiler with circulated fluid layer. The paper describes methods of thermal analysis of coal, sewage sludge and its mixtures, mud transport to the circulating fluidised bed boiler, effects on efficiency, operational reliability of the combustion equipment, emissions and solid combustion residues.

K Basin Sludge Conditioning Process Testing Partitioning of PCBs in Dissolver Solution After Neutralization/Precipitation (Caustic Adjustment)

International Nuclear Information System (INIS)

Schmidt, A.J.; Thornton, B.M.; Hoppe, E.W.; Mong, G.M.; Silvers, K.L.; Slate, S.O.

1999-01-01

The purpose of the work described in this report was to gain a better understanding of how PCB congeners present in a simulated K Basin sludge dissolver solution will partition upon neutralization and precipitation (i.e., caustic adjustment). In a previous study (Mong et al. 1998),the entire series of sludge conditioning steps (acid dissolution, filtration, and caustic adjustment) were examined during integrated testing. In the work described here, the caustic adjustment step was isolated to examine the fate of PCBs in more detail within this processing step. For this testing, solutions of dissolver simulant (containing no solids) with a known initial concentration of PCB congeners were neutralized with caustic to generate a clarified supernatant and a settled sludge phase. PCBs were quantified in each phase (including the PCBs associated with the test vessel rinsates), and material balance information was collected

Detection, phylogeny and population dynamics of syntrophic propionate - oxidizing bacteria in anaerobic granular sludge

NARCIS (Netherlands)

Harmsen, H.J.M.

1996-01-01

The research described this thesis concerns the diversity and phylogeny of syntrophic propionate-oxidizing bacteria and their ecology in granular sludge, from which they were obtained. 16S rRNA was used as a molecular marker to study both the phylogeny and the ecology of these bacteria.

Fast pyrolysis of lignin, macroalgae and sewage sludge

Energy Technology Data Exchange (ETDEWEB)

Trinh, N.T.

2013-04-15

macronutrients as N, P, K, S, Mg and Ca and this could make the chars most valuable as raw materials for fertilizer production. The sewage sludge waste bulk volume (the char compared to the sludge) was reduced with 52 % by pyrolysis at 575 deg. C. It is seen that the fast pyrolysis process provides a promising method to reduce cost for landfilling and produce a bio-oil that can be used as a fuel. The pyrolysis temperature has a considerable effect on the product distributions of the lignin and sewage sludge PCR pyrolysis, as well as their bio-oil properties with respect to molecular mass distribution, identified GC-MS component compositions, water-insoluble fraction, viscosity, and HHV. A maximum of organic oil yields of lignin and sewage sludge PCR pyrolysis were obtained at optimal temperatures of 550 - 575 deg. C. In this work, the behaviors of slurry samples of wood, char and grinded char with respect to phase transitions, rheological properties, elemental composition, and energy density were investigated. Also pumping properties were investigated at temperatures of 25, 40 and 60 deg. C and the solids loading of 0 - 20 wt%. The bioslurries obtained a volume energy density of 21-23 GJ/m{sup 3} and an energy densification factor of 4.5 - 5 (when compared to beech wood). Their apparent viscosities were significantly influenced by the solid loading levels (0 - 20 wt %) and temperatures (25 - 60 deg. C). The slurry samples with 10 wt% char (having d80 of 276 {mu}m) and 20 wt% grinded char (having d80 of 118 {mu}m) were successfully pumped into a pressurized chamber (0 - 6 bar). (LN)

Isolating strong-field dynamics in molecular systems

Science.gov (United States)

Orenstein, Gal; Pedatzur, Oren; Uzan, Ayelet J.; Bruner, Barry D.; Mairesse, Yann; Dudovich, Nirit

2017-05-01

Strong-field ionization followed by recollision provides a unique pump-probe measurement which reveals a range of electronic processes, combining sub-Angstrom spatial and attosecond temporal resolution. A major limitation of this approach is imposed by the coupling between the spatial and temporal degrees of freedom. In this paper we focus on the study of high harmonic generation and demonstrate the ability to isolate the internal dynamics—decoupling the temporal information from the spatial one. By applying an in situ approach we reveal the universality of the intrinsic pump-probe measurement and establish its validity in molecular systems. When several orbitals are involved we identify the fingerprint of the transition from the single-channel case into the multiple-channel dynamics, where complex multielectron phenomena are expected to be observed.

Heavy metals precipitation in sewage sludge

NARCIS (Netherlands)

Marchioretto, M.M.; Rulkens, W.H.; Bruning, H.

2005-01-01

There is a great need for heavy metal removal from strongly metal-polluted sewage sludges. One of the advantages of heavy metal removal from this type of sludge is the possibility of the sludge disposal to landfill with reduced risk of metals being leached to the surface and groundwater. Another

Molecular characterization of lactobacilli isolated from fermented idli batter

Directory of Open Access Journals (Sweden)

Perumal Jayaprabha Agaliya

2013-12-01

Full Text Available Lactic acid bacteria are non pathogenic organism widely distributed in nature typically involved in a large number of spontaneous food fermentation. The purpose of this study was to characterize the bacteriocinogenic lactobacilli from fermented idli batter which can find application in biopreservation and biomedicine. Eight most promising lactobacilli were chosen from twenty two isolates based on their spectrum of activity against other lactic acid bacteria and pathogens. The eight lactobacilli were characterized based on the various classical phenotypic tests, physiological tests and biochemical tests including various carbohydrate utilization profiles. All isolates were homo fermentative, catalase, and gelatin negative. Molecular characterization was performed by RAPD, 16S rRNA analysis, 16S ARDRA, and Multiplex PCR for species identification. RAPD was carried out using the primer R2 and M13. Five different clusters were obtained based on RAPD indicating strain level variation. 16S rRNA analysis showed 99 to 100% homology towards Lactobacillus plantarum. The restriction digestion pattern was similar for all the isolates with the restriction enzyme AluI. The subspecies were identified by performing Multiplex PCR using species specific primer. Among the five clusters, three clusters were clearly identified as Lactobacillus plantarum subsp. plantarum, Lactobacillus pentosus, and Lactobacillus plantarum subsp. argentoratensis.

Relative Stabilities and Reactivities of Isolated Versus Conjugated Alkenes: Reconciliation Via a Molecular Orbital Approach

Science.gov (United States)

Sotiriou-Leventis, Chariklia; Hanna, Samir B.; Leventis, Nicholas

1996-04-01

The well-accepted practice of generating a pair of molecular orbitals, one of lower energy and another of higher energy than the original pair of overlapping atomic orbitals, and the concept of a particle in a one-dimensional box are implemented in a simplified, nonmathematical method that explains the relative stabilities and reactivities of alkenes with conjugated versus isolated double bonds. In this method, Huckel-type MO's of higher polyenes are constructed by energy rules of linear combination of atomic orbitals. One additional rule is obeyed: bonding molecular orbitals overlap only with bonding molecular orbitals, and antibonding molecular orbitals overlap only with antibonding molecular orbitals.

Bio-remediation of a sludge containing hydrocarbons

International Nuclear Information System (INIS)

Ayotamuno, M.J.; Okparanma, R.N.; Nweneka, E.K.; Ogaji, S.O.T.; Probert, S.D.

2007-01-01

Bio-augmentation has been used as a bio-remediation option for hydrocarbon-contaminated, oily-sludge restoration. This sludge was obtained from the Bonny-Terminal Improvement Project (BTIP) for Bonny Island, near Port Harcourt, Nigeria. Its total hydrocarbon-content (THC) was 69,372 mg/kg of sludge. Three treatment reactors (X, Y and Z) and one control reactor (A) were charged with 1500 g of oily sludge and 250 g of agricultural soil (i.e. an oily sludge to soil ratio of 6:1), the mixture homogenized and allowed to settle for seven days before various CFUs were added to reactors X, Y and Z. Reactor A did not receive any bio-preparation. The agricultural soil served both as a nutrient and a microbe carrier. With regularly scheduled mixing and watering, the THC reduction in the oily sludge varied between 40.7% and 53.2% within two weeks as well as between 63.7% and 84.5% within six weeks of applying the bio-remediation. The CFU counts of the added bio-preparation varied between 1.2 x 12 12 and 3.0 x 10 12 CFU/g of sludge and decreased to 7.0 x 10 11 CFU/g of sludge by the end of the sixth week. The pH of the degrading sludge fluctuated between 6.5 and 7.8 during the same period. When compared with the performance of the indigenous microbes in the control sample, the added bio-preparation evidently increased the THC reduction rate in the oily sludge

Sewage sludge irradiation with electrons

International Nuclear Information System (INIS)

Tauber, M.

1976-01-01

The disinfection of sewage sludge by irradiation has been discussed very intensively in the last few months. Powerful electron accelerators are now available and the main features of the irradiation of sewage sludge with fast electrons are discussed and the design parameters of such installations described. AEG-Telefunken is building an irradiation plant with a 1.5 MeV, 25 mA electron accelerator, to study the main features of electron irradiation of sewage sludge. (author)

Placement of radium/barium sludges in tailings areas

International Nuclear Information System (INIS)

Murphy, K.L.; Multamaki, G.E.

1980-01-01

Currently radium is removed from uranium mining and milling effluents by the addition of barium chloride to precipitate the radium as radium/barium sulphate. The precipitate is allowed to settle in sedimentation basins prior to discharge of the effluent. The sedimentation basins are not suitable for final disposal of the sludge, and placement of the sludges in the tailings area has been proposed. The geochemical environment of fresh tailings areas was characterized as an acidic, oxidized surface zone underlain by an alkaline, reduced zone comprising the rest of the tailings. The quantity of sludge produced was estimated to be small relative to the quantity of tailings, and therefor a relatively small amount of radium would be added to the tailings disposal area by the addition of sludge. To confirm whether sludge addition affected radionuclide solubilization, laboratory leaching tests were conducted on slurries of acid leach tailings, and sludge-tailings mixtures. Radium in the (Ra,Ba)SO 4 sludge was at least as stable as radium in the tailings, and the sludge was able to absorb radium released from the tailings. The addition of sludge did not affect uranium and thorium solubilization. From these results it appears that the placement of sludge in tailings areas would not adversely affect the stability of radionuclides in the tailings or sludge. (auth)

Molecular typing of toxigenic Clostridum perfringens isolated from sheep in Iran

Directory of Open Access Journals (Sweden)

Abdolmohammadi Khiav, L.

2011-12-01

Full Text Available In this research a molecular method based on polymerase chain reaction for typing of Clostridiumperfringens was developed and toxin genotypes of 64 isolates from sheep and goats in Iran weredetermined. The PCR assays were developed for detection of alpha (cpa, beta (cpb and epsilon (etxtoxin genes, allowing classification of the isolates into genotypes A B, C and D. The field isolates wereassigned to genotypes A (n=9, 14.07 %, B (n=20, 31.25%, C (n=17, 26.56% and D (n=18, 28.12%. Inthis PCR system the fragments of 900, 611 and 402 bp were amplified using specific primers for alpha, beta and epsilon toxins, respectively. The fragments were confirmed by sequencing and blasting in GenBank. The sequence alignment of the fragments showed more than 98% similarity with other related published sequences from other sources. Our results suggest that PCR genotyping is an acceptable tool for in vitro typing of C. perfringens.

Deinococcus daejeonensis sp. nov., isolated from sludge in a sewage disposal plant.

Science.gov (United States)

Srinivasan, Sathiyaraj; Kim, Myung Kyum; Lim, Sangyong; Joe, Minho; Lee, Myungjin

2012-06-01

A Gram-stain-positive, strictly aerobic, spherical, non-motile red-pigmented bacterial strain, designated MJ27(T), was isolated from a sludge sample of the Daejeon sewage disposal plant in South Korea. A polyphasic approach was used to study the taxonomic position of strain MJ27(T). Strain MJ27(T) shared highest 16S rRNA gene sequence similarity with Deinococcus grandis DSM 3963(T) (98.8 %), Deinococcus caeni Ho-08(T) (97.5 %) and Deinococcus aquaticus PB314(T) (96.6 %.); levels of sequence similarity with the type strains of other Deinococcus species were less than 96.0 %. Phylogenetic analysis based on 16S rRNA gene sequences showed that strain MJ27(T) belonged to the clade formed by members of the genus Deinococcus in the family Deinococcaceae. The G+C content of the genomic DNA of strain MJ27(T) was 67.6 mol%. The chemotaxonomic characteristics of strain MJ27(T) were typical of members of the genus Deinococcus, with MK-8 as the predominant respiratory quinone, C(16:1)ω7c, C(15:1)ω6c, C(16:0) and C(15:0) as major fatty acids (>12 %), ornithine as the diamino acid in the cell-wall peptidoglycan and resistance to gamma radiation [D(10) (dose required to reduce the bacterial population by tenfold) >9 kGy]. The low levels of DNA-DNA relatedness reported here (5.3±1.5-29.2±2.3 %) indicate that strain MJ27(T) represents a species that is separate from its closest relatives in the genus Deinococcus. On the basis of phylogenetic inference, fatty acid profile and other phenotypic properties, strain MJ27(T) is considered to represent a novel species of the genus Deinococcus, for which the name Deinococcus daejeonensis sp. nov. is proposed. The type strain is MJ27(T) ( = KCTC 13751(T) = JCM 16918(T)).

Molecular characterization of Paecilomyces fumosoroseus (Deuteromycotina: Hyphomycetes isolates Caracterização molecular de isolados de Paecilomyces fumosoroseus (Deuteromycotina: Hyphomycetes

Directory of Open Access Journals (Sweden)

Andréia Cristiane Souza Azevedo

2000-12-01

Full Text Available ITS and RAPD analyses were used to investigate molecular variations within samples of Paecilomyces isolates and to resolve five morphologically atypical isolates resembling P. fumosorosus, obtained from whitefly in Northern Paraná State. The ITS4-ITS5 amplicon was 700 base pairs (bp long in all isolates. The five isolates of Paecilomyces not assigned to species produced restriction profiles identical to all the reference strains of P. fumosoroseus. The extent of fingerprint variability observed by RAPD was sufficient to discriminate all the isolates. The genetic similarity among unidentified isolates and strains of P. fumosoroseus was even higher than that observed among reference strains of this species, allowing us to conclude that isolates CNPso-P77, CNPso-P78, CNPso-P80, CNPso-P85 and CNPso-P91 are P. fumosoroseus.As análises de RAPD (Polimorfismo de DNA Amplificado ao Acaso e ITS (Sequências Internas Transcritas foram utilizadas para investigar a variabilidade molecular entre isolados de Paecilomyces e para identificar cinco isolados morfologicamente atípicos, obtidos a partir de mosca branca no Norte do Estado do Paraná, que possuíam alguma semelhança com P. fumosoroseus. O produto da amplificação com os primers ITS4 e ITS5 apresentou 700 pares de bases para todos os isolados investigados. Os cinco isolados não identificados deram origem a padrões de restrição idênticos a todas as linhagens de P. fumosoroseus utilizadas como referência. A variabilidade observada nos perfis de RAPD foi suficiente para discriminar todos os isolados. A similaridade genética entre os isolados não identificados e as linhagens de P. fumosoroseus foi maior do que aquela observada entre as linhagens referência desta espécie. Este fato permitiu concluir que os isolados CNPso-P77, CNPso-P78, CNPso-P80, CNPso-P85 and CNPso-P91 pertencem à espécie P. fumosoroseus.

Anaerobic digestion of industrial activated aerobic sludge

International Nuclear Information System (INIS)

Goodloe, J.G.; Roberts, R.S.

1990-04-01

The Tennessee Eastman Company manufactures a variety of organic chemicals, plastics and fibers at their Kingsport Tennessee Facility. The wastewater generated during the manufacture of these compounds is currently treated using an activated sludge process. The objective of the project is to evaluate the economic potential of an anaerobic digestion process to convert industrial sludge at the Tennessee Eastman Company into biogas. The evaluation will require collection and analysis of experimental data on the anaerobic digestion of industrial sludge obtained from Kingsport. Although the experiments will be conducted using Tennessee Eastman sludge, these results should be also generally applicable to similar industrial sludge

Integral study of sewage sludges

International Nuclear Information System (INIS)

1994-01-01

Sewage sludges are the by-product generated during the treatment process of waste water, and they are conformed by a solid phase which origin is the accumulation of pollutant materials which has been added to water during natural and anthropogenic activities. Its handling is one of the most serious problems faced by water treatment plants which involve the production, gathering, transportation, re utilization and final disposal of sewage sludges. The main purpose of this project is to perform a technical evaluation of the process of sewage sludge irradiation for its possible application as a choice for treatment and final disposal. Irradiation with gammas from Cobalt-60 shows effectiveness in disinfestation of sewage sludges, since they reduce six times the microbial population with a 7 KGy dose. In like manners with doses of 10 KGy is possible to bring down in 70 % the concentration of organic compounds, as well as to eliminate the presence of 6 to 22 organic compounds on samples of sewage sludges. The whole content of this work is presented in six sections: Introduction, Antecedents, Methodology, Conclusions, Suggestions and Bibliography. (Author)

Effect of sludge solids to mono-sodium titanate (MST) ratio on MST-treated sludge

International Nuclear Information System (INIS)

Saito, H.H.

1999-01-01

The Salt Disposition Systems Engineering Team has selected two cesium removal technologies for further development to replace the In-Tank Precipitation process: small tank tetraphenylborate (TPB) precipitation and crystalline silicotitanate (CST) ion exchange. In the CST ion exchange process, incoming salt solution from storage tanks containing entrained sludge solids is pretreated with monosodium titanate (MST) to adsorb strontium and plutonium. The resulting slurry is filtered using a cross-flow filter, with the permeate sent forward to CST ion exchange columns for cesium removal prior to conversion into Class A grout at the Saltstone Facility. The MST and sludge solids are to be sent for vitrification at the Defense Waste Processing Facility (DWPF). The High Level Waste Division (HLWD) requested that the Waste Processing Technology Section (WPTS) study varying the insoluble sludge solids to MST ratio to determine the relative impact of sludge and MST on filter performance. The purpose of this study was not for an exhaustive comprehensive search for an optimized insoluble sludge solids to monosodium titanate (MST) ratio, but as a scoping study to identify any effects of having an excess of either material. This document reports the results obtained

Composting sewage sludge

International Nuclear Information System (INIS)

Epstein, E.

1979-01-01

Sewage sludge is predominantly organic matter containing domestic and industrial wastes. The inefficiency of the waste water treatment to destroy pathogens and stabilization of odor-producing volatile organic compounds necessitates further treatment before sludge can be used as a soil amendment or fertilizer. Composting, which is the rapid biological decomposition of the sludge organic matter is an excellent method of sludge stabilization. During the process, volatile organics are decomposed and many of the pathogens destoyed. The low cost of the process and its flexibility with respect to labor and capital makes the system highly attractive to municipalities. A major problem facing large urban waste water treatment facilities is the distribution or marketing. The light weight of the material, expensive hauling costs, and low fertilizer value reduce its attractiveness to the agricultural sector. Thus, the greatest market is for horticultural purposes, sod, nurseries, greenhouses, parks, and reclamation areas. The major potential benefits of irradiating compost as a means of further disinfection are: (1) elimination of any health hazard; (2) increase of market potential, i.e., providing more market outlets to distribute the material; (3) compliance with state and federal health regulations; and (4) enhancement of the economics of composting as a result of utilizing compost in speciality products commanding a higher value

Method of treating radioactive sludge waste

International Nuclear Information System (INIS)

Shoji, Yuichi; Matsuura, Hiroyuki; Ichihashi, Toshio

1989-01-01

For removing water content from sludge wastes, filtration or steam condensation may be considered, but none of them can sufficiently reduce the water content since filtration may cause clogging and steam treatment has a limit in the condensation. In view of the above, radioactive sludge wastes are dehydrated by an electroosmotic process in a vessel and then dehydrated solid contents are solidified in the vessel. Since the sludge wastes are mainly composed o fion exchange resins and iron oxides deposited to the resins, when a DC voltage is applied to the sludges containing such solid contents, a force tending to premeate them through the fine pores in the filter is exerted to water. As a result, only water is removed while the solids are being held on the filters. Since the moving direction of water is different depending on the property of the sludges, the polarity of the electrodes may be changed depending on the nature of the sludges. Thus, volume reduction can be improved and treating conditions can be controlled easily by a simple device. (N.H.)

Electrochemical pretreatment of waste activated sludge: effect of process conditions on sludge disintegration degree and methane production.

Science.gov (United States)

Ye, Caihong; Yuan, Haiping; Dai, Xiaohu; Lou, Ziyang; Zhu, Nanwen

2016-11-01

Waste activated sludge (WAS) requires a long digestion time because of a rate-limiting hydrolysis step - the first phase of anaerobic digestion (AD). Pretreatment can be used prior to AD to facilitate the hydrolysis step and improve the efficiency of WAS digestion. This study evaluated a novel application of electrochemical (EC) technology employed as the pretreatment method prior to AD of WAS, focusing on the effect of process conditions on sludge disintegration and subsequent AD process. A superior process condition of EC pretreatment was obtained by reaction time of 30 min, electrolysis voltage of 20 V, and electrode distance of 5 cm, under which the disintegration degree of WAS ranged between 9.02% and 9.72%. In the subsequent batch AD tests, 206 mL/g volatile solid (VS) methane production in EC pretreated sludge was obtained, which was 20.47% higher than that of unpretreated sludge. The AD time was 19 days shorter for EC pretreated sludge compared to the unpretreated sludge. Additionally, the EC + AD reactor achieved 41.84% of VS removal at the end of AD. The analysis of energy consumption showed that EC pretreatment could be effective in enhancing sludge AD with reduced energy consumption when compared to other pretreatment methods.

On the influence of sewage sludge irradiation by gamma radiation on the sludge properties

International Nuclear Information System (INIS)

Hegemann, W.

1976-01-01

The gamma irradiation is a technically usable method to disinfect sewage sludge. Furthermore, the slurry properties are also improved. After 24 hours' thickening time, a significantly smaller volume of concentrated thick slurry could be removed compared to untreated sludge. On the other hand, a dilution occurs with pasteurization if the heat is introduced by steam, and the initial concentration could not be achieved again even after thickening for 24 hours. The drainability of the treated sludge was also improved by irradiation, expressed by a reduction of the specific filter resistance. The costs are essentially determined by the radiation sources used. If it is technically possible to process reactor wastes in such a manner that they can be used in slurry radiation plants, costs of 3.50-4.00 DM/m 3 treated sludge seem possible. (orig.) [de

Plant available nitrogen from anaerobically digested sludge and septic tank sludge applied to crops grown in the tropics.

Science.gov (United States)

Sripanomtanakorn, S; Polprasert, C

2002-04-01

Agricultural land is an attractive alternative for the disposal of biosolids since it utilises the recyclable nutrients in the production of crops. In Thailand and other tropical regions, limited field-study information exists on the effect of biosolids management strategies on crop N utilisation and plant available N (PAN) of biosolids. A field study was conducted to quantify the PAN of the applied biosolids, and to evaluate the N uptake rates of some tropical crops. Sunflower (Helianthus annuus) and tomato (Lycopersicon esculentum) were chosen in this study. Two types of biosolids used were: anaerobically digested sludge and septic tank sludge. The soil is acid sulfate and is classified as Sulfic Tropaquepts with heavy clay in texture. The anaerobically digested sludge applied rates were: 0, 156 and 312 kg N ha(-1) for the sunflower plots, and 0, 586, and 1172 kg N ha(-1) for the tomato plots. The septic tank sludge applied rates were: 0, 95 and 190 kg N ha(-1) for the sunflower plots, and 0, 354 and 708 kg N ha(-1) for the tomato plots, respectively. The results indicated the feasibility of applying biosolids to grow tropical crops. The applications of the anaerobically digested sludge and the septic tank sludge resulted in the yields of sunflower seeds and tomato fruits and the plant N uptakes comparable or better than that applied with only the chemical fertiliser. The estimated PAN of the anaerobically digested sludge was about 27-42% of the sludge organic N during the growing season. For the septic tank sludge, the PAN was about 15-58% of the sludge organic N. It is interesting to observe that an increase of the rate of septic tank sludge incorporated into this heavy clay soil under the cropping system resulted in the decrease of N mineralisation rate. This situation could cause the reduction of yield and N uptake of crops.

Enhanced sludge washing evaluation plan

Energy Technology Data Exchange (ETDEWEB)

Jensen, R.D.

1994-09-01

The Tank Waste Remediation System (TWRS) Program mission is to store, treat, and immobilize highly radioactive Hanford Site waste (current and future tank waste and the strontium/cesium capsules) in an environmentally sound, safe, and cost-effective manner. The scope of the TWRS Waste Pretreatment Program is to treat tank waste and separate that waste into HLW and LLW fractions and provide additional treatment as required to feed LLW and HLW immobilization facilities. Enhanced sludge washing was chosen as the baseline process for separating Hanford tank waste sludge. Section 1.0 briefly discusses the purpose of the evaluation plan and provides the background that led to the choice of enhanced sludge washing as the baseline process. Section 2.0 provides a brief summary of the evaluation plan details. Section 3.0 discusses, in some detail, the technical work planned to support the evaluation of enhanced sludge washing. Section 4.0 briefly discusses the potential important of policy issues to the evaluation. Section 5.0 discusses the methodology to be used in the evaluation process. Section 6.0 summarizes the milestones that have been defined to complete the enhanced sludge washing evaluation and provides a summary schedule to evaluate the performance of enhanced sludge washing. References are identified in Section 7.0, and additional schedule and milestone information is provided in the appendices.

Enhanced sludge washing evaluation plan

International Nuclear Information System (INIS)

Jensen, R.D.

1994-09-01

The Tank Waste Remediation System (TWRS) Program mission is to store, treat, and immobilize highly radioactive Hanford Site waste (current and future tank waste and the strontium/cesium capsules) in an environmentally sound, safe, and cost-effective manner. The scope of the TWRS Waste Pretreatment Program is to treat tank waste and separate that waste into HLW and LLW fractions and provide additional treatment as required to feed LLW and HLW immobilization facilities. Enhanced sludge washing was chosen as the baseline process for separating Hanford tank waste sludge. Section 1.0 briefly discusses the purpose of the evaluation plan and provides the background that led to the choice of enhanced sludge washing as the baseline process. Section 2.0 provides a brief summary of the evaluation plan details. Section 3.0 discusses, in some detail, the technical work planned to support the evaluation of enhanced sludge washing. Section 4.0 briefly discusses the potential important of policy issues to the evaluation. Section 5.0 discusses the methodology to be used in the evaluation process. Section 6.0 summarizes the milestones that have been defined to complete the enhanced sludge washing evaluation and provides a summary schedule to evaluate the performance of enhanced sludge washing. References are identified in Section 7.0, and additional schedule and milestone information is provided in the appendices

REEMISSION OF MERCURY COMPOUNDS FROM SEWAGE SLUDGE DISPOSAL

Directory of Open Access Journals (Sweden)

Beata Janowska

2016-12-01

Full Text Available The sewage sludge disposal and cultivation methods consist in storage, agricultural use, compost production, biogas production or heat treatment. The sewage sludge production in municipal sewage sludge treatment plants in year 2013 in Poland amounted to 540.3 thousand Mg d.m. The sewage sludge for agricultural or natural use must satisfy chemical, sanitary and environmental safety requirements. The heavy metal content, including the mercury content, determines the sewage sludge disposal method. Mercury has a high chemical activity and biological form compounds with different properties. The properties of the mercury present in sewage sludge or composts, its potential bioavailability depend on its physicochemical forms. Different forms of mercury, which are found in soil and sediments and sewage sludge, may be determined using various techniques sequential extraction. In order to assess the bioavailability the analysis of fractional of mercury in samples of sewage sludge and composts was made. For this purpose the analytical procedure based on a four sequential extraction process was applied. Mercury fractions were classified as exchangeable (EX, base soluble (BS, acids soluble (AS and oxidizable (OX. This article presents the research results on the mercury compounds contents in sewage sludge subjected to drying process, combustion and in composted sewage sludge. During drying and combustion process of the sewage sludge, mercury transforms into volatile forms that could be emitted into the atmosphere. The mercury fractionation in composted sewage sludge proved that mercury in compost occurs mainly in an organic fraction and in a residual fraction that are scarce in the environment.

A molecular method for typing Herpes simplex virus isolates as an alternative to immunofluorescence methods

Directory of Open Access Journals (Sweden)

Abraham A

2009-01-01

Full Text Available Background: Typing of Herpes simplex virus (HSV isolates is required to identify the virus isolated in culture. The methods available for this include antigen detection by immunofluorescence (IF assays and polymerase chain reaction (PCR. This study was undertaken to standardize a molecular method for typing of HSV and compare it with a commercial IF reagent for typing. Objectives: To compare a molecular method for typing HSV isolates with a monoclonal antibody (MAb based IF test. Study design : This cross-sectional study utilized four reference strains and 42 HSV isolates obtained from patients between September 1998 and September 2004. These were subjected to testing using an MAb-based IF test and a PCR that detects the polymerase ( pol gene of HSV isolates. Results: The observed agreement of the MAb IF assay with the pol PCR was 95.7%. Fifty four point eight percent (23/42 of isolates tested by IF typing were found to be HSV-1, 40.5% (17/42 were HSV-2, and two (4.8% were untypable using the MAb IF assay. The two untypable isolates were found to be HSV-2 using the pol PCR. In addition, the cost per PCR test for typing is estimated to be around Rs 1,300 (USD 30, whereas the cost per MAb IF test is about Rs 1,500 (USD 35 including all overheads (reagents, instruments, personnel time, and consumables. Conclusion: The pol PCR is a cheaper and more easily reproducible method for typing HSV isolates as compared to the IF test. It could replace the IF-based method for routine typing of HSV isolates as availability of PCR machines (thermal cyclers is now more widespread than fluorescence microscopes in a country like India.

40 CFR 61.54 - Sludge sampling.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Sludge sampling. 61.54 Section 61.54... sampling. (a) As an alternative means for demonstrating compliance with § 61.52(b), an owner or operator... days prior to a sludge sampling test, so that he may at his option observe the test. (c) Sludge shall...

Phenotypic and molecular characterization of Klebsiella spp. isolates causing community-acquired infections

Directory of Open Access Journals (Sweden)

U. Garza-Ramos

2018-05-01

Full Text Available Klebsiella spp. isolates from community-acquired infections were characterized. A total of 39 Klebsiella spp. isolates were obtained from outpatients at four rural hospitals in Mexico (2013–2014. The biochemical tests identified all as being K. pneumoniae. The molecular multiplex-PCR test identified 36 (92.4% K. pneumoniae isolates and one (2.5% K. variicola isolate, and phylogenetic analysis of the rpoB gene identified two isolates (5.1% belonging to K. quasipneumoniae subsp. quasipneumoniae and K. quasivariicola. The last one was confirmed by phylogenetic analysis of six-loci concatenated genes. Mostly the isolates were multidrug resistant; however, a minority were extended-spectrum β-lactamase producing (10.2%. The extended-spectrum β-lactamase CTX-M-15 gene was identified in these isolates. Analysis of biofilm production and the hypermucoviscosity phenotype showed a total of 35 (92.3% and seven (17.9% of the isolates were positive for these phenotypes respectively. The K2 (4/39, 10.2%, K5 (2/39, 5.1% and K54 (1/39, 2.5% serotypes were identified in seven (17.9% of the isolates, and only 28.5% (2/7 hypermucoviscous isolates were positive for the K2 and K5 serotypes. In general, the sequence type (ST analysis and phylogenetic analysis of seven multilocus sequence typing loci were heterogeneous; however, ST29 was the most prevalent ST in the analysed isolates, accounting for 19% (4/21 of the total isolates. Two of the four ST29 isolates had the hypermucoviscosity phenotype. The virulence factors for fimbriae were the most prevalent, followed by siderophores. Community-acquired infections are caused by various species from Klebsiella genus, with different profiles of antibiotic resistance and heterogeneous virulence factors. Keywords: Antimicrobial susceptibility, Bacterial resistance, Cephalosporin resistance, Community infection, ESBL, Hypermucoviscosity

Pentachlorophenol (PCP) sludge recycling unit

International Nuclear Information System (INIS)

1994-08-01

The Guelph Utility Pole Company treats utility poles by immersion in pentachlorophenol (PCP) or by pressure treatment with chromated copper arsenate (CCA). The PCP treatment process involves a number of steps, each producing a certain amount of sludge and other wastes. In a plant upgrading program to improve processing and treatment of poles and to reduce and recycle waste, a PCP recovery unit was developed, first as an experimental pilot-scale unit and then as a full-scale unit. The PCP recovery unit is modular in design and can be modified to suit different requirements. In a recycling operation, the sludge is pumped through a preheat system (preheated by waste heat) and suspended solids are removed by a strainer. The sludge is then heated in a tank and at a predetermined temperature it begins to separate into its component parts: oil, steam, and solids. The steam condenses to water containing low amounts of light oil, and this water is pumped through an oil/water separator. The recovered oil is reused in the wood treatment process and the water is used in the CCA plant. The oil remaining in the tank is reused in PCP treatment and the solid waste, which includes small stones and wood particles, is removed and stored. By the third quarter of operation, the recovery unit was operating as designed, processing ca 10,000 gal of sludge. This sludge yielded 6,500 gal of water, 3,500 gal of oil, and ca 30 gal of solids. Introduction of the PCP sludge recycling system has eliminated long-term storage of PCP sludge and minimized costs of hazardous waste disposal. 4 figs

Molecular epidemiology of pneumococcal isolates from children in China

Directory of Open Access Journals (Sweden)

Li-Hua Kang

2016-04-01

Full Text Available Objectives: To investigate the molecular epidemiology of pneumococcal isolates in Chongqing, China. Methods: In this cross-sectional study, 51 invasive Streptococcus pneumoniae (S. pneumoniae strains were from children with invasive pneumococcal disease (IPD and 32 carriage strains from healthy children from January 2010 to December 2013 at the Children’s Hospital of Chongqing Medical University, Chongqing, China. Multilocus sequence typing was used to identify the sequence types (STs. Capsular serotypes were determined by multiplex polymerase chain reaction. Drug susceptibility and resistance was determined by minimum inhibitory concentrations. Results: In this study, 11 serotypes were identified among the 83 S. pneumoniae clinical isolates tested. Prevalent serotypes were 19A (20.4%, 6A/B (20.4%, 19F (15.7%, 14 (14.5%, and 23F (10.8%. Serotype 19F was the most frequent carriage strain, and serotype 19A was the most frequent invasive strain. The ST983 was the most prevalent ST for carriage strains, and ST320 was the most prevalent ST for invasive strains. For gene analysis, psaA (99.5% and piaA (98.6% were present and much conserved in all pneumococci tested. The cps2A and pcsB genes were more frequent in invasive isolates than carriage strains. Antimicrobial resistance rates of invasive pneumococcal isolates to erythromycin, penicillin, meropenem, cefotaxime, and clindamycin were higher than the carriage isolates from children. Conclusion: Our epidemiological evidence shows that 19A, 6A/B, 19F, 14, and 23F remain the most prevalent serotypes, which can be targeted by PCV13. Genotypes and drug resistance varied between carriage and invasive strains. The PsaA and PiaA may be good protein vaccine candidates.

Two-stage pretreatment of excess sludge for electricity generation in microbial fuel cell.

Science.gov (United States)

Zhang, Yi; Zhao, Yang-Guo; Guo, Liang; Gao, Mengchun

2018-01-12

Thermophiles hydrolysis and acidogens fermentation were sequentially adopted to pretreat excess sludge for microbial fuel cell (MFC) electricity production. The results indicated that MFC fed with the thermophiles-acidogens pretreated sludge (MFC AB), reached a higher removal of ammonia nitrogen than the MFC fed with the heating hydrolysis and acidogens fermentation pretreated sludge (MFC NB). However, compared with the MFC AB, MFC NB presented a better performance for removal of soluble chemical oxygen demand (SCOD) (90.08%) and protein (82.42%). As for the electricity production, MFC NB obtained higher voltage of 0.632 V and maximum power density with 1.05 W/m 3 while MFC AB reached maximum voltage of 0.373 V and maximum power density of 0.58 W/m 3 . Bacterial 16S rRNA-based molecular microbial techniques showed that microbial communities on both MFC anode biofilms was diverse and different. The cooperation of fermentation bacteria and electricigen Shewanella baltica in the MFC NB may have contributed towards the improvement of electricity generation.

Successful bioaugmentation of an activated sludge reactor with Rhodococcus sp. YYL for efficient tetrahydrofuran degradation

International Nuclear Information System (INIS)

Yao, Yanlai; Lu, Zhenmei; Zhu, Fengxiang; Min, Hang; Bian, Caimiao

2013-01-01

Highlights: • Rhodococcus sp. YYL is an efficient tetrahydrofuran-degrading strain. • Strain YYL was used to augment an activated sludge system for THF degradation. • Successful bioaugmentation was achieved only by coinoculation of strain YYL and the two bacilli. • Successful bioaugmentation of the system resulted in efficient THF degradation. -- Abstract: The exchange of tetrahydrofuran (THF)-containing wastewater should significantly affect the performance of an activated sludge system. In this study, the feasibility of using THF-degrading Rhodococcus sp. strain YYL to bioaugment an activated sludge system treating THF wastewater was explored. As indicated by a DGGE analysis, strain YYL alone could not dominate the system, with the concentration of mixed liquor suspended solids (MLSS) decreasing to nearly half of the initial concentration after 45 d, and the microbial diversity was found to be significantly reduced. However, after the reactor was augmented with the mixed culture of strain YYL and two bacilli initially coexisting in the enriched isolation source, strain YYL quickly became dominant in the system and was incorporated into the activated sludge. The concentration of MLSS increased from 2.1 g/L to 7.3 g/L in 20 d, and the efficiency of THF removal from the system was remarkably improved. After the successful bioaugmentation, more than 95% of THF was completely removed from the wastewater when 20 mM THF was continuously loaded into the system. In conclusion, our research first demonstrates that bioaugmentation of activated sludge system for THF degradation is feasible but that successful bioaugmentation should utilize a THF-degrading mixed culture as the inoculum, in which the two bacilli might help strain YYL colonize in activated sludge by co-aggregation

REEMISSION OF MERCURY COMPOUNDS FROM SEWAGE SLUDGE DISPOSAL

OpenAIRE

Beata Janowska

2016-01-01

The sewage sludge disposal and cultivation methods consist in storage, agricultural use, compost production, biogas production or heat treatment. The sewage sludge production in municipal sewage sludge treatment plants in year 2013 in Poland amounted to 540.3 thousand Mg d.m. The sewage sludge for agricultural or natural use must satisfy chemical, sanitary and environmental safety requirements. The heavy metal content, including the mercury content, determines the sewage sludge disposal metho...

Factors affecting the consolidation of steam generator sludge

Energy Technology Data Exchange (ETDEWEB)

Turner, C. W.; Shamsuzzaman, K.; Tapping, R. L.

1993-02-15

It is hypothesized that sludge consolidation is promoted by chemical reactions involving the various sludge constituents, although the hardness of the final product will also depend on the total porosity. Oxidizing conditions and higher temperatures produce a harder sludge. The precipitation of Zn{sub 2}SiO{sub 4}, a potential binding agent, may also promote sludge consolidation. Several solutions to prevent sludge consolidation are suggested. (Author) 3 figs., 4 tabs., 3 refs.

Membrane bioreactor (MBR) sludge inoculation in a hybrid process scheme concept to assist overloaded conventional activated sludge (CAS) process operations.

Science.gov (United States)

Fenu, A; Roels, J; Van Damme, S; Wambecq, T; Weemaes, M; Thoeye, C; De Gueldre, G; Van De Steene, B

2012-01-01

This study analyzes the effect of inoculating membrane bioreactor (MBR) sludge in a parallel-operated overloaded conventional activated sludge (CAS) system. Modelling studies that showed the beneficial effect of this inoculation were confirmed though full scale tests. Total nitrogen (TN) removal in the CAS increased and higher nitrate formation rates were achieved. During MBR sludge inoculation, the TN removal in the CAS was proven to be dependent on MBR sludge loading. Special attention was given to the effect of inoculation on sludge quality. The MBR flocs, grown without selection pressure, were clearly distinct from the more compact flocs in the CAS system and also contained more filamentous bacteria. After inoculation the MBR flocs did not evolve into good-settling compact flocs, resulting in a decreasing sludge quality. During high flow conditions the effluent CAS contained more suspended solids. Sludge volume index, however, did not increase. Laboratory tests were held to determine the threshold volume of MBR sludge to be seeded into the CAS reactor. Above 16-30%, supernatant turbidity and scum formation increased markedly.

Waste sludge resuspension and transfer: development program

International Nuclear Information System (INIS)

Weeren, H.O.; Mackey, T.S.

1980-02-01

The six Gunite waste tanks at Oak Ridge National Laboratory (ORNL) contain about 400,000 gal of sludge that has precipitated from solution and settled during the 35 years these tanks have been in service. Eventual decommissioning of the tanks has been proposed. The first part of this program is to resuspend the accumulated sludge, to transfer it to new storage tanks in Melton Valley, and to dispose of it by the shale-fracturing process. On the basis of preliminary information, a tentative operational concept was adopted. The sludge in each tank would be resuspended by hydraulic sluicing and pumped from the tank. This resuspended sludge would be treated as necessary to keep the particles in suspension and would be pumped to the new waste-storage tanks. Subsequently the sludge would be pumped from the tanks, combined with a cement-base mix, and disposed of by the shale-fracturing facility. Verification of the feasibility of this concept required development effort on characterization of the sludge and development of techniques for resuspending the sludge and for keeping it in suspension. These development efforts are described in this report. Sections of the report describe both the known properties of the sludge and the tests of grinding methods investigated, discuss tests of various suspenders, describe tests with cement-base mixes, summarize hot-cell tests on actual sludge samples, and describe tests that were made at a mockup of a Gunite tank installation. On the basis of the tests made, it was concluded that reslurrying and resuspension of the sludge is quite feasible and that the suspensions can be made compatible with cement mixes

Full-scale effects of addition of sludge from water treatment stations into processes of sewage treatment by conventional activated sludge.

Science.gov (United States)

Luiz, Marguti André; Sidney Seckler, Ferreira Filho; Passos, Piveli Roque

2018-06-01

An emerging practice for water treatment plant (WTP) sludge is its disposal in wastewater treatment plants (WWTP), an alternative that does not require the installation of sludge treatment facilities in the WTP. This practice can cause both positive and negative impacts in the WWTP processes since the WTP sludge does not have the same characteristics as domestic wastewater. This issue gives plenty of information in laboratory and pilot scales, but lacks data from full-scale studies. The main purpose of this paper is to study the impact of disposing sludge from the Rio Grande conventional WTP into the ABC WWTP, an activated sludge process facility. Both plants are located in São Paulo, Brazil, and are full-scale facilities. The WTP volumetric flow rate (4.5 m³/s) is almost three times that of WWTP (1.6 m³/s). The data used in this study came from monitoring the processes at both plants. The WWTP liquid phase treatment analysis included the variables BOD, COD, TSS, VSS, ammonia, total nitrogen, phosphorus and iron, measured at the inlet, primary effluent, mixed liquor, and effluent. For the WWTP solids treatment, the parameters tested were total and volatile solids. The performance of the WWTP process was analyzed with and without sludge addition: 'without sludge' in years 2005 and 2006 and 'with sludge' from January 2007 to March 2008. During the second period, the WTP sludge addition increased the WWTP removal efficiencies for solids (93%-96%), organic matter (92%-94% for BOD) and phosphorus (52%-88%), when compared to the period 'without sludge'. These improvements can be explained by higher feed concentrations combined to same or lower effluent concentrations in the 'with sludge' period. No critical negative impacts occurred in the sludge treatment facilities, since the treatment units absorbed the extra solids load from the WTP sludge. Copyright © 2018 Elsevier Ltd. All rights reserved.

Evaluation of molecular markers for Phytophthora ramorum detection and identification using a standardized library of isolates

Science.gov (United States)

F.N. Martin; M. Coffey; R. Hamelin; P. Tooley; M. Garbelotto; K. Hughes; T. Kubisiak

2008-01-01

A number of molecular diagnostic procedures for detection of Phytophthora ramorum have been reported in the literature. In an effort to evaluate the specificity of 10 of these techniques a standardized DNA library for 317 isolates was assembled that included 60 described species as well as 22 taxonomically unclassified isolates. These were sent blind...

Molecular characterisation of Aspergillus flavus isolates from peanut fields in India using AFLP

Directory of Open Access Journals (Sweden)

Diwakar Singh

2015-09-01

Full Text Available Aflatoxin contamination of peanut, due to infection by Aspergillus flavus, is a major problem of rain-fed agriculture in India. In the present study, molecular characterisation of 187 Aspergillus flavus isolates, which were sampled from the peanut fields of Gujarat state in India, was performed using AFLP markers. On a pooled cluster analysis, the markers could successfully discriminate among the ‘A’, ‘B’ and ‘G’ group A. flavus isolates. PCoA analysis also showed equivalent results to the cluster analysis. Most of the isolates from one district could be clustered together, which indicated genetic similarity among the isolates. Further, a lot of genetic variability was observed within a district and within a group. The results of AMOVA test revealed that the variance within a population (84% was more than that between two populations (16%. The isolates, when tested by indirect competitive ELISA, showed about 68.5% of them to be atoxigenic. Composite analysis between the aflatoxin production and AFLP data was found to be ineffective in separating the isolate types by aflatoxigenicity. Certain unique fragments, with respect to individual isolates, were also identified that may be used for development of SCAR marker to aid in rapid and precise identification of isolates.

Radioactivity of sludge in Finland in 1987

International Nuclear Information System (INIS)

Puhakainen, M.; Rahola, T.

1989-05-01

Sewage sludge from municipal wastewater treatment plants was studied to determine its radionuclide concentrations. Measurements were made to find out whether any radionuclides from the nuclear power stations at Loviisa and Olkiluoto and from hospitals and medical laboratories could be detected in sludge additional to those originating from global and Chernobyl fallout. In the treatment process of water, aluminium sulphate sludge is developed at treatment plants using surface water. This kind of sludge was measured since it also concentrates radionuclides. Fallout nuclides from the Chernobyl nuclear power station after the accident predominated in all sewage sludge samples in Finland. In 1987 six different radionuclides originating from the Chernobyl fallout were detected in sewage sludge. In spring when the snow melted and large quantities of run off water flowed into the treatment plants, the activity concentrations clearly increased, but then started decreasing again. At the end of the year the highest measured 137 Cs activity concentrations were below 1000 Bq kg -1 dry weight. The highest activity concentration in sludge originated from iodine used fro medical purposes

Isolate extended state in the DNA molecular transistor with surface interaction

Energy Technology Data Exchange (ETDEWEB)

Wang, Le, E-mail: wang_le917@gs.zzu.edu.cn; Qin, Zhi-Jie

2016-02-01

The field effect characteristic of a DNA molecular device is investigated in a tight binding model with binary disorder and side site correlation. Using the transfer-matrix method and Landauer–Büttiker theory, we find that the system has isolated extended state that is irrespective of the DNA sequence and can be modulated by the gate voltage. When the gate voltage reaches some proper value, the isolated extended state appears at the Fermi level of the system and the long range charge transport is greatly enhanced. We attribute this phenomenon to the combination of the external field, the surface interaction, and the intrinsic disorder of DNA. The result is a generic feature of the nanowire with binary disorder and surface interaction.

Evaluation of the influence of mechanical activation on physical and chemical properties of municipal solid waste incineration sludge.

Science.gov (United States)

Caprai, V; Florea, M V A; Brouwers, H J H

2018-06-15

Despite numerous studies concerning the application of by-products in the construction field, municipal solid waste incineration (MSWI) residues are not widely used as secondary building materials. In some European countries, washing treatment to the full bottom ash (BA) fraction (0-32 mm) is applied, isolating more contaminated particles, smaller than 0.063 mm. Therefore, a MWSI sludge is produced, having a high moisture content, and thus a limited presence of soluble species. In order to enhance its performance as building material, here, dry mechanical activation is applied on MSWI sludge. Thereafter, a reactivity comparison between reference BA and untreated and treated MSWI sludge is provided, evaluating their behaviour in the presence of cement and their pozzolanic activity. Moreover, the mechanical performances, as 25% substitution of Portland cement (PC) are assessed, based on the EN 450. Mechanical activation enhances MSWI sludge physically due to the improved particle morphology and packing. Chemically, the hydration degree of PC is enhanced by the MSWI sludge by ≈25%. The milling treatment proved to be beneficial to the residues performances in the presence of PC, providing 32% higher strength than untreated sample. Environmentally, the compliance with the unshaped material legislation is successfully verified, according to the Soil Quality Decree. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sewage sludge and liquid pig manure as possible sources of antibiotic resistant bacteria.

Science.gov (United States)

Hölzel, Christina S; Schwaiger, Karin; Harms, Katrin; Küchenhoff, Helmut; Kunz, Anne; Meyer, Karsten; Müller, Christa; Bauer, Johann

2010-05-01

Within the last decades, the environmental spread of antibiotic resistant bacteria has become a topic of concern. In this study, liquid pig manure (n=305) and sewage sludge (n=111) - used as agricultural fertilizers between 2002 and 2005 - were investigated for the presence of Escherichia coli, Enterococcus faecalis and Enterococcus faecium. Bacteria were tested for their resistance against 40 chemotherapeutics including several "reserve drugs". E. coli (n=613) from pig manure were at a significantly higher degree resistant to streptomycin, doxycycline, spectinomycin, cotrimoxazole, and chloramphenicol than E. coli (n=116) from sewage sludge. Enterococci (Ent. faecalis, n=387, and Ent. faecium, n=183) from pig manure were significantly more often resistant to high levels of doxycycline, rifampicin, erythromycin, and streptomycin than Ent. faecalis (n=44) and Ent. faecium (n=125) from sewage sludge. Significant differences in enterococcal resistance were also seen for tylosin, chloramphenicol, gentamicin high level, fosfomycin, clindamicin, enrofloxacin, moxifloxacin, nitrofurantoin, and quinupristin/dalfopristin. By contrast, aminopenicillins were more effective in enterococci from pig manure, and mean MIC-values of piperacillin+tazobactam and third generation cefalosporines were significantly lower in E. coli from pig manure than in E. coli from sewage sludge. 13.4% (E. coli) to 25.3% (Ent. faecium) of pig manure isolates were high-level multiresistant to substances from more than three different classes of antimicrobial agents. In sewage sludge, high-level-multiresistance reached from 0% (Ent. faecalis) to 16% (Ent. faecium). High rates of (multi-) resistant bacteria in pig manure emphasize the need for a prudent - cautious - use of antibiotics in farm animals. Copyright 2010 Elsevier Inc. All rights reserved.

Copper stabilization in beneficial use of waterworks sludge and copper-laden electroplating sludge for ceramic materials.

Science.gov (United States)

Tang, Yuanyuan; Chan, Siu-Wai; Shih, Kaimin

2014-06-01

A promising strategy for effectively incorporating metal-containing waste materials into a variety of ceramic products was devised in this study. Elemental analysis confirmed that copper was the predominant metal component in the collected electroplating sludge, and aluminum was the predominant constituent of waterworks sludge collected in Hong Kong. The use of waterworks sludge as an aluminum-rich precursor material to facilitate copper stabilization under thermal conditions provides a promising waste-to-resource strategy. When sintering the mixture of copper sludge and the 900 °C calcined waterworks sludge, the CuAl2O4 spinel phase was first detected at 650 °C and became the predominant product phase at temperatures higher than 850 °C. Quantification of the XRD pattern using the Rietveld refinement method revealed that the weight of the CuAl2O4 spinel phase reached over 50% at 850 °C. The strong signals of the CuAl2O4 phase continued until the temperature reached 1150 °C, and further sintering initiated the generation of the other copper-hosting phases (CuAlO2, Cu2O, and CuO). The copper stabilization effect was evaluated by the copper leachability of the CuAl2O4 and CuO via the prolonged leaching experiments at a pH value of 4.9. The leaching results showed that the CuAl2O4 phase was superior to the CuAlO2 and CuO phases for immobilizing hazardous copper over longer leaching periods. The findings clearly indicate that spinel formation is the most crucial metal stabilization mechanism when sintering multiphase copper sludge with aluminum-rich waterworks sludge, and suggest a promising and reliable technique for reusing both types of sludge waste for ceramic materials. Copyright © 2013 Elsevier Ltd. All rights reserved.

Supplementary information on K-Basin sludges

International Nuclear Information System (INIS)

MAKENAS, B.J.

1999-01-01

Three previous documents in this series have been published covering the analysis of: K East Basin Floor and Pit Sludge, K East Basin Canister Sludge, and K West Basin Canister Sludge. Since their publication, additional data have been acquired and analyses performed. It is the purpose of this volume to summarize the additional insights gained in the interim time period

Molecular Typing of Neisseria gonorrhoeae Isolates by Opa-Typing and Ribotyping in New Delhi, India

Directory of Open Access Journals (Sweden)

Pejvak Khaki

2009-01-01

Full Text Available Control and preventive measures for gonococcal infections are based on precise epidemiological characteristics of N. gonorrhoeae isolates. In the present study the potential utility of opa-typing and ribotyping for molecular epidemiological study of consecutive gonococcal strains was determined. Sixty gonococcal isolates were subjected to ribotyping with two restriction enzymes, AvaII and HincII, and opa-typing with TaqI and HpaII for epidemiological characterization of gonococcal population. Ribotyping with AvaII yielded 6 ribotype patterns while twelve RFLP patterns were observed with HincII. Opa-typing of the 60 isolates revealed a total 54 opa-types, which 48 were unique and 6 formed clusters. Fifty-two opa-types were observed with TaqI-digested PCR product while opa-typing with HpaII demonstrated 54 opa-types. The opa-types from isolates that were epidemiologically unrelated were distinct, whereas those from the sexual contacts were identical. The results showed that opa-typing is highly useful for characterizing gonococcal strains from sexual contacts and has more discriminatory than ribotyping that could differentiate between gonococci of the same ribotype. The technique even with a single restriction enzyme has a high level of discrimination (99.9% between epidemiologically unrelated isolates. In conclusion, the molecular methods such as opa-typing and ribotyping can be used for epidemiological characterization of gonococcal strains.

Molecular Typing of Neisseria gonorrhoeae Isolates by Opa-Typing and Ribotyping in New Delhi, India

Science.gov (United States)

Khaki, Pejvak; Bhalla, Preena; Fayaz, Ahmad Mir; Moradi Bidhendi, Sohiela; Esmailzadeh, Majid; Sharma, Pawan

2009-01-01

Control and preventive measures for gonococcal infections are based on precise epidemiological characteristics of N. gonorrhoeae isolates. In the present study the potential utility of opa-typing and ribotyping for molecular epidemiological study of consecutive gonococcal strains was determined. Sixty gonococcal isolates were subjected to ribotyping with two restriction enzymes, AvaII and HincII, and opa-typing with TaqI and HpaII for epidemiological characterization of gonococcal population. Ribotyping with AvaII yielded 6 ribotype patterns while twelve RFLP patterns were observed with HincII. Opa-typing of the 60 isolates revealed a total 54 opa-types, which 48 were unique and 6 formed clusters. Fifty-two opa-types were observed with TaqI-digested PCR product while opa-typing with HpaII demonstrated 54 opa-types. The opa-types from isolates that were epidemiologically unrelated were distinct, whereas those from the sexual contacts were identical. The results showed that opa-typing is highly useful for characterizing gonococcal strains from sexual contacts and has more discriminatory than ribotyping that could differentiate between gonococci of the same ribotype. The technique even with a single restriction enzyme has a high level of discrimination (99.9%) between epidemiologically unrelated isolates. In conclusion, the molecular methods such as opa-typing and ribotyping can be used for epidemiological characterization of gonococcal strains. PMID:20016674

K-Basins Sludge Treatment and Packaging at the Hanford Site - 13585

International Nuclear Information System (INIS)

Fogwell, Thomas W.; Honeyman, James O.; Stegen, Gary

2013-01-01

Highly radioactive sludge resulting from the storage of degraded spent nuclear fuel has been consolidated in Engineered Containers (ECs) in the 105-K West Storage Basin located on the Hanford site near the Columbia River in Washington State. CH2M Hill Plateau Remediation Company (CHPRC) is proceeding with a project to retrieve the sludge, place it in Sludge Transport and Storage Containers (STSCs) and store those filled containers within the T Plant Canyon facility on the Hanford Site Central Plateau (Phase 1). Retrieval and transfer of the sludge material will enable removal of the 105-K West Basin and allow remediation of the subsurface contamination plumes under the basin. The U.S. Department of Energy (DOE) plans to treat and dispose of this K Basins sludge (Phase 2) as Remote Handled Transuranic Waste (RH TRU) at the Waste Isolation Pilot Plant (WIPP) located in New Mexico. The K Basin sludge currently contains uranium metal which reacts with water present in the stored slurry, generating hydrogen and other byproducts. The established transportation and disposal requirements require the transformation of the K Basins sludge to a chemically stable, liquid-free, packaged waste form. The Treatment and Packaging Project includes removal of the containerised sludge from T Plant, the treatment of the sludge as required, and packaging of all the sludge into a form that is certifiable for transportation to and disposal at WIPP. Completion of this scope will require construction and operation of a Sludge Treatment and Packaging Facility (STPF), which could be either a completely new facility or a modification of an existing Hanford Site facility. A Technology Evaluation and Alternatives Analysis (TEAA) for the STP Phase 2 was completed in 2011. A Request for Technology Information (RFI) had been issued in October 2009 to solicit candidate technologies for use in Phase 2. The RFI also included a preliminary definition of Phase 2 functions and requirements. Potentially

K-Basins Sludge Treatment and Packaging at the Hanford Site - 13585

Energy Technology Data Exchange (ETDEWEB)

Fogwell, Thomas W. [Fogwell Consulting, P.O. Box 20211, Piedmont, CA 94620 (United States); Honeyman, James O. [CH2M HILL Plateau Remediation Company, P.O. Box 1600 H7-30, Richland, WA (United States); Stegen, Gary [Lucas Engineering and Management Services, Inc., 1201 Jadwin Avenue, Suite 102, Richland, WA 99352 (United States)

2013-07-01

Highly radioactive sludge resulting from the storage of degraded spent nuclear fuel has been consolidated in Engineered Containers (ECs) in the 105-K West Storage Basin located on the Hanford site near the Columbia River in Washington State. CH2M Hill Plateau Remediation Company (CHPRC) is proceeding with a project to retrieve the sludge, place it in Sludge Transport and Storage Containers (STSCs) and store those filled containers within the T Plant Canyon facility on the Hanford Site Central Plateau (Phase 1). Retrieval and transfer of the sludge material will enable removal of the 105-K West Basin and allow remediation of the subsurface contamination plumes under the basin. The U.S. Department of Energy (DOE) plans to treat and dispose of this K Basins sludge (Phase 2) as Remote Handled Transuranic Waste (RH TRU) at the Waste Isolation Pilot Plant (WIPP) located in New Mexico. The K Basin sludge currently contains uranium metal which reacts with water present in the stored slurry, generating hydrogen and other byproducts. The established transportation and disposal requirements require the transformation of the K Basins sludge to a chemically stable, liquid-free, packaged waste form. The Treatment and Packaging Project includes removal of the containerised sludge from T Plant, the treatment of the sludge as required, and packaging of all the sludge into a form that is certifiable for transportation to and disposal at WIPP. Completion of this scope will require construction and operation of a Sludge Treatment and Packaging Facility (STPF), which could be either a completely new facility or a modification of an existing Hanford Site facility. A Technology Evaluation and Alternatives Analysis (TEAA) for the STP Phase 2 was completed in 2011. A Request for Technology Information (RFI) had been issued in October 2009 to solicit candidate technologies for use in Phase 2. The RFI also included a preliminary definition of Phase 2 functions and requirements. Potentially

Epidemiology, clinical manifestations, and molecular typing of salmonella typhi isolated from patients with typhoid fever in Lebanon.

Science.gov (United States)

Kanj, Souha S; Kanafani, Zeina A; Shehab, Marwa; Sidani, Nisreen; Baban, Tania; Baltajian, Kedak; Dakdouki, Ghenwa K; Zaatari, Mohamad; Araj, George F; Wakim, Rima Hanna; Dbaibo, Ghassan; Matar, Ghassan M

2015-06-01

The objective of this study was to examine the epidemiology and the clinical manifestations of typhoid fever as well as the susceptibility and strain relatedness of Salmonella typhi isolates in Lebanon from 2006 to 2007. A total of 120 patients with typhoid fever were initially identified from various areas of the country based on positive culture results for S. typhi from blood, urine, stools, bone marrow and/or positive serology. Clinical, microbiological and molecular analysis was performed on cases with complete data available. These results indicated that drinking water was an unlikely mode of transmission of the infection. Despite increasing reports of antimicrobial resistance among S. typhi isolates, the vast majority of these isolates were susceptible to various antibiotic agents, including ampicillin, cephalosporins, quinolones, and trimethoprim/sulfamethoxazole. Molecular analysis of the isolates revealed a predominance of one single genotype with no variation in distribution across the geographical regions. Copyright © 2014 Ministry of Health, Saudi Arabia. Published by Elsevier Ltd. All rights reserved.

Molecular assessment of complex microbial communities degrading long chain fatty acids (LCFA) in methanogenic bioreactors

NARCIS (Netherlands)

Sousa, D.Z.; Pereira, M.A.; Smidt, H.; Stams, A.J.M.; Alves, M.M.

2007-01-01

Microbial diversity of anaerobic sludge after extended contact with long chain fatty acids (LCFA) was studied using molecular approaches. Samples containing high amounts of accumulated LCFA were obtained after continuous loading of two bioreactors with oleate or with palmitate. These sludge samples

Treatment and disposal of refinery sludges: Indian scenario.

Science.gov (United States)

Bhattacharyya, J K; Shekdar, A V

2003-06-01

Crude oil is a major source of energy and feedstock for petrochemicals. Oily sludge, bio-sludge and chemical sludge are the major sludges generated from the processes and effluent treatment plants of the refineries engaged in crude oil refining operations. Refineries in India generate about 28,220 tons of sludge per annum. Various types of pollutants like phenols, heavy metals, etc. are present in the sludges and they are treated as hazardous waste. Oily sludge, which is generated in much higher amount compared to other sludges, contains phenol (90-100 mg/kg), nickel (17-25 mg/kg), chromium (27-80 mg/kg), zinc (7-80 mg/kg), manganese (19-24 mg/kg), cadmium (0.8-2 mg/kg), copper (32-120 mg/kg) and lead (0.001-0.12 mg/ kg). Uncontrolled disposal practices of sludges in India cause degradation of environmental and depreciation of aesthetic quality. Environmental impact due to improper sludge management has also been identified. Salient features of various treatment and disposal practices have been discussed. Findings of a case study undertaken by the authors for Numaligarh Refinery in India have been presented. Various system alternatives have been identified for waste management in Numaligarh Refinery. A ranking exercise has been carried out to evaluate the alternatives and select the appropriate one. A detailed design of the selected waste management system has been presented.

Disintegration impact on sludge digestion process.

Science.gov (United States)

Dauknys, Regimantas; Rimeika, Mindaugas; Jankeliūnaitė, Eglė; Mažeikienė, Aušra

2016-11-01

The anaerobic sludge digestion is a widely used method for sludge stabilization in wastewater treatment plant. This process can be improved by applying the sludge disintegration methods. As the sludge disintegration is not investigated enough, an analysis of how the application of thermal hydrolysis affects the sludge digestion process based on full-scale data was conducted. The results showed that the maximum volatile suspended solids (VSS) destruction reached the value of 65% independently on the application of thermal hydrolysis. The average VSS destruction increased by 14% when thermal hydrolysis was applied. In order to have the maximum VSS reduction and biogas production, it is recommended to keep the maximum defined VSS loading of 5.7 kg VSS/m(3)/d when the thermal hydrolysis is applied and to keep the VSS loading between 2.1-2.4 kg VSS/m(3)/d when the disintegration of sludge is not applied. The application of thermal hydrolysis leads to an approximately 2.5 times higher VSS loading maintenance comparing VSS loading without the disintegration; therefore, digesters with 1.8 times smaller volume is required.

Conversion of paper sludge to ethanol, II: process design and economic analysis.

Science.gov (United States)

Fan, Zhiliang; Lynd, Lee R

2007-01-01

Process design and economics are considered for conversion of paper sludge to ethanol. A particular site, a bleached kraft mill operated in Gorham, NH by Fraser Papers (15 tons dry sludge processed per day), is considered. In addition, profitability is examined for a larger plant (50 dry tons per day) and sensitivity analysis is carried out with respect to capacity, tipping fee, and ethanol price. Conversion based on simultaneous saccharification and fermentation with intermittent feeding is examined, with ethanol recovery provided by distillation and molecular sieve adsorption. It was found that the Fraser plant achieves positive cash flow with or without xylose conversion and mineral recovery. Sensitivity analysis indicates economics are very sensitive to ethanol selling price and scale; significant but less sensitive to the tipping fee, and rather insensitive to the prices of cellulase and power. Internal rates of return exceeding 15% are projected for larger plants at most combinations of scale, tipping fee, and ethanol price. Our analysis lends support to the proposition that paper sludge is a leading point-of-entry and proving ground for emergent industrial processes featuring enzymatic hydrolysis of cellulosic biomass.

Revegetation of mined land using waste water sludge

Energy Technology Data Exchange (ETDEWEB)

Sopper, W E; Kerr, N

1980-01-01

The benefits of using sludge to reclaim land that has been used for strip mining is explained. Pennsylvania State University developed demonstration plots and used various types of sludges to illustrate this. One application of sludge is sufficient to supply plant nutrients for 3-5 years. After sludge application and incorporation, the site was broadcast seeded with grasses and legumes. Other trials and their results are noted. All show no detrimental effects on vegetation, the soil or groundwater quality due to sludge application.

Gravity Drainage of Activated Sludge on Reed Beds

DEFF Research Database (Denmark)

Christensen, Morten Lykkegaard; Dominiak, Dominik Marek; Keiding, Kristian

and operation of reed beds and the efficiencies are often lower than predicted. One reason is that the sludge quality varies from plant to plant and even within plants from time to time. No good method exists for measuring the sludge quality with respect to drainage characteristics. A new experimental method...... has therefore been developed to measure relevant quality parameters: specific cake resistance, settling velocity and cake compressibility. It has been found that activated sludge form highly compressible cake even at the low compressive pressures obtained during drainage. Numerical simulation shows......Activated sludge is a by-product from waste water treatment plants, and the water content in the sludge is high (> 90%). Among several methods to remove the water, sludge drying reed beds are often used to dewater the sludge by drainage. There is, however, no well-defined criterion for design...

SLUDGE WASHING AND DEMONSTRATION OF THE DWPF FLOWSHEET IN THE SRNL SHIELDED CELLS FOR SLUDGE BATCH 7A QUALIFICATION

Energy Technology Data Exchange (ETDEWEB)

Pareizs, J.; Billings, A.; Click, D.

2011-07-08

Waste Solidification Engineering (WSE) has requested that characterization and a radioactive demonstration of the next batch of sludge slurry (Sludge Batch 7a*) be completed in the Shielded Cells Facility of the Savannah River National Laboratory (SRNL) via a Technical Task Request (TTR). This characterization and demonstration, or sludge batch qualification process, is required prior to transfer of the sludge from Tank 51 to the Defense Waste Processing Facility (DWPF) feed tank (Tank 40). The current WSE practice is to prepare sludge batches in Tank 51 by transferring sludge from other tanks. Discharges of nuclear materials from H Canyon are often added to Tank 51 during sludge batch preparation. The sludge is washed and transferred to Tank 40, the current DWPF feed tank. Prior to transfer of Tank 51 to Tank 40, SRNL simulates the Tank Farm and DWPF processes with a Tank 51 sample (referred to as the qualification sample). Sludge Batch 7a (SB7a) is composed of portions of Tanks 4, 7, and 12; the Sludge Batch 6 heel in Tank 51; and a plutonium stream from H Canyon. SRNL received the Tank 51 qualification sample (sample ID HTF-51-10-125) following sludge additions to Tank 51. This report documents: (1) The washing (addition of water to dilute the sludge supernate) and concentration (decanting of supernate) of the SB7a - Tank 51 qualification sample to adjust sodium content and weight percent insoluble solids to Tank Farm projections. (2) The performance of a DWPF Chemical Process Cell (CPC) simulation using the washed Tank 51 sample. The simulation included a Sludge Receipt and Adjustment Tank (SRAT) cycle, where acid was added to the sludge to destroy nitrite and reduce mercury, and a Slurry Mix Evaporator (SME) cycle, where glass frit was added to the sludge in preparation for vitrification. The SME cycle also included replication of five canister decontamination additions and concentrations. Processing parameters were based on work with a non

Clinical data and molecular analysis of Mycobacterium tuberculosi isolates from drug-resistant tuberculosis patients in Goiás, Brazil

Directory of Open Access Journals (Sweden)

Sueli Lemes de Ávila Alves

2011-09-01

Full Text Available Drug resistance is one of the major concerns regarding tuberculosis (TB infection worldwide because it hampers control of the disease. Understanding the underlying mechanisms responsible for drug resistance development is of the highest importance. To investigate clinical data from drug-resistant TB patients at the Tropical Diseases Hospital, Goiás (GO, Brazil and to evaluate the molecular basis of rifampin (R and isoniazid (H resistance in Mycobacterium tuberculosis. Drug susceptibility testing was performed on 124 isolates from 100 patients and 24 isolates displayed resistance to R and/or H. Molecular analysis of drug resistance was performed by partial sequencing of the rpoB and katGgenes and analysis of the inhA promoter region. Similarity analysis of isolates was performed by 15 loci mycobacterial interspersed repetitive unit-variable number tandem repeat (MIRU-VNTR typing. The molecular basis of drug resistance among the 24 isolates from 16 patients was confirmed in 18 isolates. Different susceptibility profiles among the isolates from the same individual were observed in five patients; using MIRU-VNTR, we have shown that those isolates were not genetically identical, with differences in one to three loci within the 15 analysed loci. Drug-resistant TB in GO is caused by M. tuberculosis strains with mutations in previously described sites of known genes and some patients harbour a mixed phenotype infection as a consequence of a single infective event; however, further and broader investigations are needed to support our findings.

K Basin Sludge Conditioning Testing. Nitric Acid Dissolution Testing of K East Area Sludge Composite, Small- and Large-Scale Testing

International Nuclear Information System (INIS)

Carlson, C.D.; Delegard, C.H.; Burgeson, I.E.; Schmidt, A.J.; Silvers, K.L.

1998-01-01

This report describes work performed by Pacific Northwest National Laboratory (PNNL) for Numatec Hanford Corporation (NHC) to support the development of the K Basin Sludge Treatment System. For this work, testing was performed to examine the dissolution behavior of a K East Basin floor and Weasel Pit sludge composite, referred to as K East area sludge composite, in nitric acid at the following concentrations: 2 M, 4 M, 6 M and 7.8 M. With the exception of one high solids loading test the nitric acid was added at 4X the stoichiometric requirement (assuming 100% of the sludge was uranium metal). The dissolution tests were conducted at boiling temperatures for 24 hours. Most of the tests were conducted with approximately2.5 g of sludge (dry basis). The high solids loading test was conducted with approximately7 g of sludge. A large-scale dissolution test was conducted with 26.5 g of sludge and 620 mL of 6 M nitric acid. The objectives of this test were to (1) generate a sufficient quantity of acid-insoluble residual solids for use in leaching studies, and (2) examine the dissolution behavior of the sludge composite at a larger scale

Relationship between organic matter humification and bioavailability of sludge-borne copper and cadmium during long-term sludge amendment to soil

Energy Technology Data Exchange (ETDEWEB)

Liu, Hongtao, E-mail: liuht@igsnrr.ac.cn

2016-10-01

Recycling of sludge as soil amendment poses certain risk of heavy metals contamination. This study investigated the relationship between organic matter in composted sludge and its heavy metals bioavailability over 7 years. Periodic monitoring indicated a gradual increase in organic matter degradation, accompanied by changing degrees of polymerization, i.e., ratio of humic acid (HA)/fulvic acid (FA) coupled with incremental exchangeable fraction of copper (Cu) in sludge, with a growing rate of 74.7%, rather than that in soil. However, cadmium (Cd) in composted sludge exhibited an independent manner. Linear-regression analysis revealed that the total proportion of the Cu active fraction (exchangeable plus carbonate bound) was better correlated with the degree of polymerization (DP) and humification ratio (HR) than the degradation ratio of organic matter. Overall, amount of uptaken Cu was more dependent on the humification degree of organic matter, especially the proportion of HA in humus. - Highlights: • Organic matter in sludge degraded with time goes after sludge was recycled to soil. • DP in sludge is well coupled with incremental uptaken fraction of its borne copper. • Profiles of Cadmium fractions in sludge exhibit an independent manner.

Fermentation and chemical treatment of pulp and paper mill sludge

Science.gov (United States)

Lee, Yoon Y; Wang, Wei; Kang, Li

2014-12-02

A method of chemically treating partially de-ashed pulp and/or paper mill sludge to obtain products of value comprising taking a sample of primary sludge from a Kraft paper mill process, partially de-ashing the primary sludge by physical means, and further treating the primary sludge to obtain the products of value, including further treating the resulting sludge and using the resulting sludge as a substrate to produce cellulase in an efficient manner using the resulting sludge as the only carbon source and mixtures of inorganic salts as the primary nitrogen source, and including further treating the resulting sludge and using the resulting sludge to produce ethanol.

Technology for improving sludge concentration; Odei noshukusei kaizen gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-10

Sludge generating in a sewage treatment plant is disposed through the processes such as concentration, dehydration, and incineration in sludge disposal facilities. In recent years, there has been a trend that this sludge increases in volume as well as worsens in the concentration. A case is predictable where the sludge load to the dehydrating process is so large that the sludge can no longer be processed in sufficient quantity. In the meantime, if sludge is ozone-treated, viscous substance on the surface of sludge particles can be separated with a comparatively small amount of ozone, with sludge concentration enhanced. At Meidensha, an experimental plant was set up for the ozone treatment of sludge in a sludge intensive treatment plant of a metropolis, with a verification experiment carried out for a sludge concentration improving system by ozone. As a result of comparison of the treatment performance between an assessment system for performing ozone treatment and a reference system for not performing, the average value of the sludge concentration of a gravity concentration tank was 1.9% of the reference system against 1.7% of the assessment system in a continuous treatment experiment in the summer, while the solid collection ratio was 65.8% of the reference system against 95.5% of the assessment system, enabling a superior improving effect to be obtained. (NEDO)

Gravitational sedimentation of flocculated waste activated sludge.

Science.gov (United States)

Chu, C P; Lee, D J; Tay, J H

2003-01-01

The sedimentation characteristics of flocculated wastewater sludge have not been satisfactorily explored using the non-destructive techniques, partially owing to the rather low solid content (ca. 1-2%) commonly noted in the biological sediments. This paper investigated, for the first time, the spatial-temporal gravitational settling characteristics of original and polyelectrolyte flocculated waste activated sludge using Computerized Axial Tomography Scanner. The waste activated sludge possessed a distinct settling characteristic from the kaolin slurries. The waste activated sludges settled more slowly and reached a lower solid fraction in the final sediment than the latter. Flocculation markedly enhanced the settleability of both sludges. Although the maximum achievable solid contents for the kaolin slurries were reduced, flocculation had little effects on the activated sludge. The purely plastic rheological model by Buscall and White (J Chem Soc Faraday Trans 1(83) (1987) 873) interpreted the consolidating sediment data, while the purely elastic model by Tiller and Leu (J. Chin. Inst. Chem. Eng. 11 (1980) 61) described the final equilibrated sediment. Flocculation produced lower yield stress during transient settling, thereby resulting in the more easily consolidated sludge than the original sample. Meanwhile, the flocculated activated sludge was stiffer in the final sediment than in the original sample. The data reported herein are valuable to the theories development for clarifier design and operation.

Siloxane removal and sludge disintegration using thermo-alkaline treatments with air stripping prior to anaerobic sludge digestion

International Nuclear Information System (INIS)

Oshita, Kazuyuki; Fujime, Motochika; Takaoka, Masaki; Fujimori, Takashi; Appels, Lise; Dewil, Raf

2015-01-01

Highlights: • Siloxanes hamper the energy-use of anaerobic digestion biogas. • D5 siloxane was considered as target compound in this study. • The treatment removed 80% of D5 in sewage sludge at 55 °C and 135 g-NaOH kg −1 -VTS. • D5 removal and the disintegration of VSS in the sludge were correlated. • At the optimal conditions, the costs of anaerobic digestion were notably diminished. - Abstract: A thermo-alkaline treatment with air stripping was applied before anaerobic sludge digestion for both siloxane removal and sludge disintegration. The treatment was expected to increase the amount of biogas produced and to reduce the amount of siloxane in the gas. Adding sodium hydroxide (NaOH) to the sludge improved the removal of siloxane from the sludge, with approximately 90% of the siloxane removed to the gas phase using a thermo-alkaline treatment. Over 80% of decamethylcyclopentasiloxane (D5) could be removed under the following conditions: 55 °C treatment temperature, 135 g-NaOH kg −1 volatile total solids (VTS), and 0.5 L min −1 air-stripping rate. The disintegration ratio of volatile suspended solids (VSS) in the sludge was correlated with the D5 removal ratio. Because most of the siloxane was adsorbed to, or was contained in the VSS, the siloxane removal ratio increased with VSS disintegration. Finally, the energy consumption and operational costs of this system were evaluated for several scenarios. Thermo-alkaline treatment at the indicated operational conditions had the lowest operating costs for a 400 m 3 day −1 anaerobic sludge digestion system

Gravity settling of Hanford single-shell tank sludges

International Nuclear Information System (INIS)

Brooks, K.P.; Rector, D.R.; Smith, P.A.

1999-01-01

The US Department of Energy plans to use gravity settling in million-gallon storage tanks while pretreating sludge on the Hanford site. To be considered viable in these large tanks, the supernatant must become clear, and the sludge must be concentrated in an acceptable time. These separations must occur over the wide range of conditions associated with sludge pretreatment. In the work reported here, gravity settling was studied with liter quantities of actual single-shell tank sludge from hanford Tank 241-C-107. Because of limited sludge availability, an approach was developed using the results of these liter-scale tests to predict full-scale operation. Samples were centrifuged at various g-forces to simulate compaction with higher layers of sludge. A semi-empirical settling model was then developed incorporating both the liter-scale settling data and the centrifuge compression results to describe the sludge behavior in a million-gallon tank. The settling model predicted that the compacted sludge solids would exceed 20 wt% in less than 30 days of settling in a 10-m-tall tank for all pretreatment steps

Analysis of the biological and molecular variability of the Polish isolates of Tomato black ring virus (TBRV).

Science.gov (United States)

Rymelska, N; Borodynko, N; Pospieszny, H; Hasiów-Jaroszewska, B

2013-10-01

Tomato black ring virus (TBRV) is an important pathogen infecting many plant species worldwide. The biological and molecular variability of the Polish isolates of TBRV was analyzed. The analysis was performed based on the symptoms induced by various isolates on test plant species as well as on phylogenetic relationships between isolates. Isolates differed in their host range and symptomatology. In addition, genetic variation among isolates was characterized by restriction fragment length polymorphism analysis and confirmed by sequencing. The phylogenetic analysis revealed that the Polish isolates differ from each other and do not form a monophyletic cluster. Finally, we identified and analyzed sequences of defective RNA forms arising from the TBRV genome.

Factors Involved in Sludge Granulation under Anaerobic Conditions

Directory of Open Access Journals (Sweden)

Jalal Shayegan

2011-03-01

Full Text Available This paper investigates the effects of factors involved in sludge anaerobic granulation. Granulated sludge formation is the main parameter contributing to the success of UASB reactors. Anaerobic granulation leads to reduced reactor size, space requirement, and investment costs. Operation costs are also greatly reduced due to lack of aeration. An important parameter affecting process performance is the size of sludge granules; the factors involved in granule size will be investigated. Some of the important parameters of anaerobic sludge granulation are: existence of growth cores as inert particles or granulated sludge, process operational conditions (Sludge Loading Rate and Organic Loading Rate, Loading rate increase and …, and environment conditions (nutrients, temperature, pH, combination and ….

SLUDGE WASHING AND DEMONSTRATION OF THE DWPF FLOWSHEET IN THE SRNL SHIELDED CELLS FOR SLUDGE BATCH 5 QUALIFICATION

Energy Technology Data Exchange (ETDEWEB)

Pareizs, J; Cj Bannochie, C; Damon Click, D; Dan Lambert, D; Michael Stone, M; Bradley Pickenheim, B; Amanda Billings, A; Ned Bibler, N

2008-11-10

Sludge Batch 5 (SB5) is predominantly a combination of H-modified (HM) sludge from Tank 11 that underwent aluminum dissolution in late 2007 to reduce the total mass of sludge solids and aluminum being fed to the Defense Waste Processing Facility (DWPF) and Purex sludge transferred from Tank 7. Following aluminum dissolution, the addition of Tank 7 sludge and excess Pu to Tank 51, Liquid Waste Operations (LWO) provided the Savannah River National Laboratory (SRNL) a 3-L sample of Tank 51 sludge for SB5 qualification. SB5 qualification included washing the sample per LWO plans/projections (including the addition of a Pu/Be stream from H Canyon), DWPF Chemical Process Cell (CPC) simulations, waste glass fabrication (vitrification), and waste glass chemical durability evaluation. This report documents: (1) The washing (addition of water to dilute the sludge supernatant) and concentration (decanting of supernatant) of the Tank 51 qualification sample to adjust sodium content and weight percent insoluble solids to Tank Farm projections. (2) The performance of a DWPF CPC simulation using the washed Tank 51 sample. This includes a Sludge Receipt and Adjustment Tank (SRAT) cycle, where acid is added to the sludge to destroy nitrite and remove mercury, and a Slurry Mix Evaporator (SME) cycle, where glass frit is added to the sludge in preparation for vitrification. The SME cycle also included replication of five canister decontamination additions and concentrations. Processing parameters for the CPC processing were based on work with a non radioactive simulant. (3) Vitrification of a portion of the SME product and Product Consistency Test (PCT) evaluation of the resulting glass. (4) Rheology measurements of the initial slurry samples and samples after each phase of CPC processing. This work is controlled by a Task Technical and Quality Assurance Plan (TTQAP) , and analyses are guided by an Analytical Study Plan. This work is Technical Baseline Research and Development (R

Ceramsite preparation from sea sludge with sewage sludge biochar and its environmental risk assessment

Science.gov (United States)

Li, Jie; Yu, Guangwei; Pan, Lanjia; Li, Chunxing; Xie, Shengyu; Wang, Gang; Wang, Yin

2018-02-01

Ceramsite were produced from sea sludge (SS) by adding different percentage of sewage sludge biochar (SSB). The characteristics of ceramsite including micrograph and elementary composition were analyzed. In addition, the heavy metals (HMs) fractions, leaching behaviour and potential environmental risk were also investigated. The microstructure of the ceramsite was slit pores and the main elements of the ceramsite were Si, Al and O. The residual fraction (F4) of Cu, Cr and Cd in ceramsite with 100% SS (SS100) reached the maximum (100%, 99% and 100%, respectively), while F4 of Zn and Ni in ceramsite with 80% SS and 20% SSB (SS80) reached the top value of 99.5% and 98%. Moreover, the HMs of feedstock can be immobilized after sintering as ceramsite and the leached amounts of HMs in all ceramsite were much lower than that stated by GB 5085.3-2007. Furthermore, ceramsite preparation from sea sludge with sewage sludge biochar will not bring HMs contamination and potential ecological risk.

PENERAPAN ELEKTROOSMOSIS UNTUK PENGERINGAN SLUDGE DARI PENGOLAHAN LIMBAH CAIR

Directory of Open Access Journals (Sweden)

Darmawan Darmawan

2013-11-01

Full Text Available APPLICATION OF ELECTROOSMOSIS FOR DEWATERING OF SLUDGE FROM WASTE WATER TREATMENT. Wastewater treatment produces semi-solid residue (sludge that must be handled carefully during dumping and discharge to avoid polluting the environment. A low cost and easy treatment of dewatering is needed. This research aimed to apply electroosmosis technique for dewatering sludge in order to seek for parameters that can efficiently reduce water content of sludge, including range of voltage, type of electrodes, and distance between electrodes; and to determine the effect of electroosmosis processes on changes of chemical characteristics of sludge. The results showed that: (1 electroosmosis dewatering occurred on the sludge taken from waste water treatment of landfill but not on sludge from water purification plant (PDAM, (2 direct current voltage of 30 volts was the optimum voltage, (3 copper rod cathode provided electroosmosis process as good as stainless steel cathode and both were better than the woven stainless steel cathode, (4 the dewatering time to reduce 1200% (w/w water content to about 400% was about 40 hours for sludge of 2500 cm3 in volume (laboratory bench scale, (5 the anode need to reinserted gradually approaching the cathode due to current lost when the water content at the anode point reached 400% and sludge at the point shrink, and (6 some chemical elements in the sludge decreased significantly after treatment. Pengolahan limbah cair menghasilkan residu berupa bahan semi padat yang dikenal sebagai sludge. Sludge tersebut juga perlu dikelola penyimpanan dan pembuangannya agar tidak mencemari lingkungan. Salah satu pengelolaan sludge yang perlu dilakukan adalah pengeringan (dewatering. Salahsatu teknik dewatering yang mungkin diterapkan ialah teknik elektroosmosis, yaitu teknik yang memanfaatkan adanya pergerakan air pada media poros di dalam medan istrik searah. Penelitian ini bertujuan untuk mencari parameter sistem dewatering secara

Physical property characterization of 183-H Basin sludge

International Nuclear Information System (INIS)

Biyani, R.K.; Delegard, C.H.

1995-01-01

This document describes the characterization of 183-H Basin sludge physical properties, e.g. bulk density of sludge and absorbent, and determination of free liquids. Calcination of crucible-size samples of sludge was also done and the resulting 'loss-on-ignition' was compared to the theoretical weight loss based on sludge analysis obtained from Weston Labs

Changes on sewage sludge stability after greenhouse drying

Science.gov (United States)

Soriano-Disla, J. M.; Houot, S.; Imhoff, M.; Valentin, N.; Gómez, I.; Navarro-Pedreño, J.

2009-04-01

The progressive implementation of the Urban Waste Water Treatment Directive 91/271/EEC in all the European member states is increasing the quantities of sewage sludge requiring disposal. Sludge application onto cultivated soils as organic fertilizers allows the recycling of nutrients. The application of only dehydrated sludges has generated many problems including unpleasant odours and difficult management (regarding transport and application) related to their high water content. One way to overcome these problems, in a cheap and clean way, is the drying of sludges using the energy of the sun under greenhouse conditions. This drying may affect sludge chemical characteristics including organic matter stability and nitrogen availability, parameters which have to be controlled for the proper management of dry sludge application onto soils. For this reason, the main aim of this work was to study the impact of greenhouse drying of different sewage sludges on their organic matter stability and nitrogen availability, assessed by biochemical fractionation and mineralization assays. Three sewage sludges were sampled before (dehydrated sludges) and after greenhouse drying (dried sludges). The analyses consisted of: humidity, organic matter, mineral and organic N contents, N and C mineralization during 91-day laboratory incubations in controlled conditions, and biochemical fractionation using the Van Soest procedure. Greenhouse drying decreased the water content from 70-80% to 10% and also the odours, both of which will improve the management of the final product from the perspective of application and transport. We also found that drying reduced the organic matter content of the sludges but not the biodegradability of the remaining carbon. Organic N mineralization occurred during greenhouse drying, explaining why mineral N content tended to increase and the potential mineralization of organic nitrogen decreased after greenhouse drying. The biochemical stability did not

SEROLOGICAL DETECTION AND MOLECULAR CHARACTERIZATION OF A BEGOMOVIRUS ISOLATE OBTAINED FROM Macroptilium lathyroides

Directory of Open Access Journals (Sweden)

JOSÉ ALBERSIO DE ARAUJO LIMA

2012-01-01

Full Text Available The viruses from the genus Begomovirus, family Geminiviridae are considered emergent pathogens, mainly because of the population explosion of their insect vectors. For this reason, more attention needs to be directed to the correct virus species identification inside the genus. The present paper had the objectives of serologically detecting a begomovirus in Macroptilium lathyroides plants in the State of Ceará, and developing biological, serological and molecular studies with a virus isolate obtained from M. lathyroides. Indirect ELISA with antiserum for Macroptilium golden mosaic virus (MaGMV demonstrated that the samples collected from M. lathyroides showing golden mosaic in the field were infected with a begomovirus. The virus isolate obtained was transmitted by grafting to eight species of the family Leguminosae, four species of Solonaceae, and one species in the family Amaranthaceae. The virus also was transmitted from M. lathyroides to M. lathyroides by the whitefly Bemisia tabaci biotype B. A DNA fragment of 1.2 kb was obtained by PCR with the primers PAL1v 1978 and PAR1c 496 for component A, and a DNA fragment of 0.5 kb was obtained with the primers PBL1v 2040 and PCR cl for component B, confirming the presence of a begomovirus infecting M. lathyroides. Molecular studies indicated that the begomovirus isolate showed 77% genomic similarity with Bean golden mosaic virus and 75% with Cowpea golden mosaic virus for their cp and rep genes, indicating the possibility that the isolate is a distinct virus species of the Begomovirus genus.

Mitigation of Membrane Biofouling in MBR Using a Cellulolytic Bacterium, Undibacterium sp. DM-1, Isolated from Activated Sludge.

Science.gov (United States)

Nahm, Chang Hyun; Lee, Seonki; Lee, Sang Hyun; Lee, Kibaek; Lee, Jaewoo; Kwon, Hyeokpil; Choo, Kwang-Ho; Lee, Jung-Kee; Jang, Jae Young; Lee, Chung-Hak; Park, Pyung-Kyu

2017-03-28

Biofilm formation on the membrane surface results in the loss of permeability in membrane bioreactors (MBRs) for wastewater treatment. Studies have revealed that cellulose is not only produced by a number of bacterial species but also plays a key role during formation of their biofilm. Hence, in this study, cellulase was introduced to a MBR as a cellulose-induced biofilm control strategy. For practical application of cellulase to MBR, a cellulolytic ( i.e ., cellulase-producing) bacterium, Undibacterium sp. DM-1, was isolated from a lab-scale MBR for wastewater treatment. Prior to its application to MBR, it was confirmed that the cell-free supernatant of DM-1 was capable of inhibiting biofilm formation and of detaching the mature biofilm of activated sludge and cellulose-producing bacteria. This suggested that cellulase could be an effective anti-biofouling agent for MBRs used in wastewater treatment. Undibacterium sp. DM-1-entrapping beads ( i.e ., cellulolytic-beads) were applied to a continuous MBR to mitigate membrane biofouling 2.2-fold, compared with an MBR with vacant-beads as a control. Subsequent analysis of the cellulose content in the biofilm formed on the membrane surface revealed that this mitigation was associated with an approximately 30% reduction in cellulose by cellulolytic-beads in MBR.

Sewage sludge and how to sell it

Energy Technology Data Exchange (ETDEWEB)

Knapp, I M

1977-10-01

Largo, Florida dries its sludge and sells it as fertilizer for $80 to $169/T. The sludge processing plant capable of turning common sludge into a dry, pelletized soil conditioner was only slightly more expensive than the previously proposed concrete drying beds which would have required disposal of the dried residue. The city's experience in setting up the plant and marketing the finished product is discussed. The true advantage of selling heat-dried sludge is that residents of the surrounding area, knowing the value of the product to their lawns and shrubs, will provide the transportation for the product and the physical labor to spread it over an area wider than most municipalities could afford to own or operate. The current production cost of $140/T is high, but the addition of a sludge prethickener-conditioner process and expected future economies of scale as the volume of sludge treated increases should lower per ton costs.

Addition of biochar to sewage sludge decreases freely dissolved PAHs content and toxicity of sewage sludge-amended soil.

Science.gov (United States)

Stefaniuk, Magdalena; Oleszczuk, Patryk

2016-11-01

Due to an increased content of polycyclic aromatic hydrocarbons (PAHs) frequently found in sewage sludges, it is necessary to find solutions that will reduce the environmental hazard associated with their presence. The aim of this study was to determine changes of total and freely dissolved concentration of PAHs in sewage sludge-biochar-amended soil. Two different sewage sludges and biochars with varying properties were tested. Biochars (BC) were produced from biogas residues at 400 °C or 600 °C and from willow at 600 °C. The freely dissolved PAH concentration was determined by means of passive sampling using polyoxymethylene (POM). Total and freely dissolved PAH concentration was monitored at the beginning of the experiment and after 90 days of aging of the sewage sludge with the biochar and soil. Apart from chemical evaluation, the effect of biochar addition on the toxicity of the tested materials on bacteria - Vibrio fischeri (Microtox ® ), plants - Lepidium sativum (Phytotestkit F, Phytotoxkit F), and Collembola - Folsomia candida (Collembolan test) was evaluated. The addition of biochar to the sewage sludges decreased the content of C free PAHs. A reduction from 11 to 43% of sewage sludge toxicity or positive effects on plants expressed by root growth stimulation from 6 to 25% to the control was also found. The range of reduction of C free PAHs and toxicity was dependent on the type of biochar. After 90 days of incubation of the biochars with the sewage sludge in the soil, C free PAHs and toxicity were found to further decrease compared to the soil with sewage sludge alone. The obtained results show that the addition of biochar to sewage sludges may significantly reduce the risk associated with their environmental use both in terms of PAH content and toxicity of the materials tested. Copyright © 2016 Elsevier Ltd. All rights reserved.

Isolation, enumeration, molecular identification and probiotic potential evaluation of lactic acid bacteria isolated from sheep milk

Directory of Open Access Journals (Sweden)

L.B. Acurcio

2014-06-01

Full Text Available Lactic acid bacteria species were molecularly identified in milk from Lacaune, Santa Inês and crossbred sheep breeds and their in vitro probiotic potential was evaluated. The species identified were Enterococcus faecium (56.25%, E. durans (31.25% and E. casseliflavus (12.5%. No other lactic acid bacteria species, such as lactobacilli, was identified. Most of the isolated enterococci were resistant to gastric pH (2.0 and to 0.3% oxgall. All tested enterococci were resistant to ceftazidime, oxacillin and streptomycin and sensible to clindamycin, erythromycin and penicillin. The resistance to ciprofloxacin, gentamicin, tetracycline and vancomycin varied among tested species. All tested enterococci strongly inhibited (P<0.05 Escherichia coli and Listeria monocytogenes, moderately inhibited E. faecalis and Staphylococcus aureus and did not inhibit Pseudomonas aeruginosa, Salmonella enterica var. Typhimurium and also one E. durans sample isolated from sheep milk. Four samples of E. faecium, one of E. durans and one of E. casseliflavus presented the best probiotic potential.

Effects of ultrasonic disintegration on sludge microbial activity and dewaterability

International Nuclear Information System (INIS)

Li Huan; Jin Yiying; Mahar, Rasool Bux; Wang Zhiyu; Nie Yongfeng

2009-01-01

Ultrasonic treatment can disintegrate sludge, enhance microbial activity and improve sludge dewaterability at different energy inputs. To find their relationship, the three phenomena during ultrasonic treatment were investigated synchronously, and an experimental model was established to describe the process of ultrasonic sludge disintegration. Analysis results showed that the changes of sludge microbial activity and dewaterability were dependent on sludge disintegration degree during ultrasonic treatment. When sludge disintegration degree was lower than 20%, sludge flocs were disintegrated into micro-floc aggregates and the microbial activity increased over 20%. When sludge disintegration degree was over 40%, most cells were destroyed at different degree, and sludge activity decreased drastically. Only when sludge disintegration degree was 2-5%, sludge dewaterability was improved with the conditioning of FeCl 3 . It was also found that the sonication with low density and long duration was more efficient than sonication with high density and short duration at the same energy input for sludge disintegration, and a transmutative power function model can be used to describe the process of ultrasonic disintegration

Effects of ultrasonic disintegration on sludge microbial activity and dewaterability.

Science.gov (United States)

Huan, Li; Yiying, Jin; Mahar, Rasool Bux; Zhiyu, Wang; Yongfeng, Nie

2009-01-30

Ultrasonic treatment can disintegrate sludge, enhance microbial activity and improve sludge dewaterability at different energy inputs. To find their relationship, the three phenomena during ultrasonic treatment were investigated synchronously, and an experimental model was established to describe the process of ultrasonic sludge disintegration. Analysis results showed that the changes of sludge microbial activity and dewaterability were dependent on sludge disintegration degree during ultrasonic treatment. When sludge disintegration degree was lower than 20%, sludge flocs were disintegrated into micro-floc aggregates and the microbial activity increased over 20%. When sludge disintegration degree was over 40%, most cells were destroyed at different degree, and sludge activity decreased drastically. Only when sludge disintegration degree was 2-5%, sludge dewaterability was improved with the conditioning of FeCl(3). It was also found that the sonication with low density and long duration was more efficient than sonication with high density and short duration at the same energy input for sludge disintegration, and a transmutative power function model can be used to describe the process of ultrasonic disintegration.

Test plan, sludge retrieval, sludge packaging

International Nuclear Information System (INIS)

Feigenbutz, L.V.

1994-01-01

This document provides direction for the cold testing of tools, equipment and systems which will be installed and operated in K-East (KE) Basin in support of the sludge retrieval and packaging project. The technical uncertainties related to the effectiveness of sludge retrieval procedures and equipment require that cold testing be completed before installation in KE Basin to identify and resolve existing problems, and to optimize the efficiency of all equipment and systems used. This plan establishes the responsibilities, test requirements, and documentation requirements necessary to complete cold tests of: (1) equipment with no potential for plant use; (2) prototype equipment and systems which may be upgraded for use in K-Basin; and (3) plant equipment and systems requiring cold acceptance testing prior to plant use. Some equipment and systems may have been subject to a formal design review and safety assessment; the results of which will be included as supporting documents to the operational readiness review (ORR)

Rapid thermal conditioning of sewage sludge

Science.gov (United States)

Zheng, Jianhong

Rapid thermal conditioning (RTC) is a developing technology recently applied to sewage sludge treatment. Sludge is heated rapidly to a reaction temperature (up to about 220sp°C) under sufficient pressure to maintain the liquid phase. Reaction is quenched after 10 to 30 seconds when the mixture of sludge and steam pass through a pressure let-down valve. This process reduces the amount of sludge requiring land disposal, eliminates the need for polymer coagulant, improves dewaterability, increases methane production, and further reduces the concentration of pathogens. The odor problem associated with traditional thermal conditioning processes is largely minimized. Ammonia removal is readily integrated with the process. For this research, a pilot unit was constructed capable of processing 90 liters of sludge per hour. Over 22 runs were made with this unit using sludge from New York City Water Pollution Control Plants (WPCP). Sludges processed in this equipment were tested to determine the effect of RTC operating conditions on sludge dewaterability, biodegradability, and other factors affecting the incorporation of RTC into wastewater treatment plants. Dewaterability of thermally conditioned sludge was assessed for cetrifugeability and filterability. Bench scale centrifugation was used for evaluating centrifugeability, pressure filtration and capillary suction time (CST) for filterability. A mathematical model developed for centrifuge dewatering was used to predict the effect of RTC on full scale centrifuge performance. Particle size distribution and solids density of raw and treated PDS were also analyzed. An observed increase in sludge solids density at least partially explains its improved centrifugeability. An investigation of thermally conditioned amino acids showed that the L-isomer is highly biodegradable while the D-isomers are generally less so. Glucose is highly biodegradable, but rapidly becomes refractory as thermal conditioning time is lengthened. This

Biodegradation of benzalkonium chlorides singly and in mixtures by a Pseudomonas sp. isolated from returned activated sludge

International Nuclear Information System (INIS)

Khan, Adnan Hossain; Topp, Edward; Scott, Andrew; Sumarah, Mark; Macfie, Sheila M.; Ray, Madhumita B.

2015-01-01

Highlights: • Pseudomonas sp. degraded two benzalkonium chlorides: BDDA and BDTA. • Although BDTA biodegraded at low concentration, it inhibited the degradation of BDDA. • For BDDA, two transformation products indicate two sites of bacterial activity. • "1"4C-labelled BDDA was mineralized to "1"4CO_2 within 300 h. - Abstract: Bactericidal cationic surfactants such as quaternary ammonium compounds (QACs) are widely detected in the environment, and found at mg kg"−"1 concentrations in biosolids. Although individual QACs are amenable to biodegradation, it is possible that persistence is increased for mixtures of QACs with varying structure. The present study evaluated the biodegradation of benzyl dimethyl dodecyl ammonium chloride (BDDA) singly and in the presence of benzyl dimethyl tetradecyl ammonium chloride (BDTA) using Pseudomonas sp., isolated from returned activated sludge. Growth was evaluated, as was biodegradation using "1"4C and HPLC-MS methods. BDTA was more toxic to growth of Pseudomonas sp. compared to BDDA, and BDTA inhibited BDDA biodegradation. The benzyl ring of [U-"1"4C-benzyl] BDDA was readily and completely mineralized. The detection of the transformation products benzyl methyl amine and dodecyl dimethyl amine in spent culture liquid was consistent with literature. Overall, this study demonstrates the antagonistic effect of interactions on biodegradation of two widely used QACs suggesting further investigation on the degradation of mixture of QACs in wastewater effluents and biosolids.

Isolation and Characterization of Hydrocarbon-utilizing Bacteria from ...

African Journals Online (AJOL)

Isolation and Characterization of Hydrocarbon-utilizing Bacteria from Petroleum Sludge Samples obtained from Crude Oil Processing Facility in Nigeria. ... Journal Home > Vol 21, No 2 (2017) > ... Algeria (5); Benin (2); Botswana (3); Burkina Faso (3); Cameroon (8); Congo, Republic (1); Côte d'Ivoire (4); Egypt, Arab Rep.

Hydraulic conductivity and soil-sewage sludge interactions

Directory of Open Access Journals (Sweden)

Silvio Romero de Melo Ferreira

2011-10-01

Full Text Available One of the main problems faced by humanity is pollution caused by residues resulting from the production and use of goods, e.g, sewage sludge. Among the various alternatives for its disposal, the agricultural use seems promising. The purpose of this study was to evaluate the hydraulic conductivity and interaction of soil with sandy-silty texture, classified as Spodosols, from the Experimental Station Itapirema - IPA, in Goiana, state of Pernambuco, in mixtures with sewage sludge from the Mangueira Sewage Treatment Station, in the city of Recife, Pernambuco at rates of 25, 50 and 75 Mg ha-1. Tests were conducted to let water percolate the natural saturated soil and soil-sludge mixtures to characterize their physical, chemical, and microstructural properties as well as hydraulic conductivity. Statistical data analysis showed that the presence of sewage sludge in soils leads to an increase of the < 0.005 mm fraction, reduction in real specific weight and variation in optimum moisture content from 11.60 to 12.90 % and apparent specific dry weight from 17.10 and 17.50 kN m-3. In the sludge-soil mixture, the quartz grains were covered by sludge and filling of the empty soil macropores between grains. There were changes in the chemical characteristics of soil and effluent due to sewage sludge addition and a small decrease in hydraulic conductivity. The results indicate the possibility that soil acidity influenced the concentrations of the elements found in the leachate, showing higher levels at higher sludge doses. It can be concluded that the leaching degree of potentially toxic elements from the sewage sludge treatments does not harm the environment.

Molecular characterization of salmonella isolated from patients at a local hospital in Islamabad

International Nuclear Information System (INIS)

Iftikhar, F.; Sultana, K.

2011-01-01

The present study is based on molecular characterization of 17 clinical isolates of Salmonella obtained from Children's Hospital, PIMS, Islamabad, Pakistan. Whole cell protein profile analysis of all the isolates was similar and did not reveal any difference within the population. However, analysis of outer membrane protein profiles showed that the isolates fell into two groups on the basis of level of expression and presence or absences of two peptide, i.e. 48 Kd and 43 Kd. A 27 Kd outer membrane protein was expressed strongly only in one isolate. Analysis of purified lipopolysaccharide fractions obtained from Salmonella paratyphi showed a lower optical density/absorption, i.e. 1.003 as compared to the fractions obtained from Salmonella typhoid i.e. 2.001-2.224. Western blot analysis of cell lysate fraction against sera from a typhoid patient indicated that four major outer membrane protein bands were immunogenic. The data revealed a 46 Kd outer membrane protein to be highly immunogenic which was not reported earlier. (author)

Experience with a pilot plant for the irradiation of sewage sludge: Bacteriological and parasitological studies after irradiation

International Nuclear Information System (INIS)

Wizigmann, I.; Wuersching, F.

1975-01-01

Comparative bacteriological studies of sewage sludge in a sewage plant have demonstrated that mechanical-biological sewage treatment reduced the total bacterial count and those of Enterococces by 2 log and the Enterobacteriaceae by 3-4 log. Frequently Salmonella could be isolated from sewage sludge. A further reduction of viable micro-organisms could be achieved by irradiation of sewage sludge ( 60 Co, gamma-radiation, 260 krad, 210 min). This reduction amounted to an average of 2 log with Enterococces and total bacterial count, and to 5 log with Enterobacteriaceae. Out of 40 samples investigated after irradiation, two contained Salmonella. The hygienic effects of the irradiation unit were demonstrated by means of a model experiment with bacterial pure cultures. Micro-organisms of different species as well as strains of the same species differ in their sensitivity to irradiation. Parasitological experiments with eggs of Ascaris suum were carried out to test the inhibitory or killing ability of the gamma rays on the developing stages of parasites

Isolation and Molecular Identification of Some Blue-Green Algae (Cyanobacteria from Freshwater Sites in Tokat Province of Turkey

Directory of Open Access Journals (Sweden)

Tunay Karan

2017-11-01

Full Text Available Collected blue-green algae (cyanobacteria from freshwater sites throughout Tokat province and its outlying areas were isolated in laboratory environment and their morphological systematics were determined and also their species identifications were studied by molecular methods. Seven different species of blue-green algae collected from seven different sites were isolated by purifying in cultures in laboratory environment. DNA extractions were made from isolated cells and extracted DNAs were amplified by using PCR. Cyanobacteria specific primers were used to amplify 16S rRNA and phycocyanine gene regions using PCR. Phylogenetic identification of species were conducted by evaluation of obtained sequence analysis data by using computer software. According to species identification by sequence analysis, it was seen that molecular data supports morphological systematics.

methoxyethanol by a new bacterium isolate Pseudomonas sp. Strain

African Journals Online (AJOL)

Michael Horsfall

A 2-methoxyethanol degrading bacterium was isolated from anaerobic sludge of a municipal sewage from ... Stoichiometrically, the strain utilized one mole of oxygen per one mole of 2-methoxyethanol instead of ... physiological and biochemical characterization of the .... observed with acetate and the intact resting cells.

Sewage sludge solubilization by high-pressure homogenization.

Science.gov (United States)

Zhang, Yuxuan; Zhang, Panyue; Guo, Jianbin; Ma, Weifang; Fang, Wei; Ma, Boqiang; Xu, Xiangzhe

2013-01-01

The behavior of sludge solubilization using high-pressure homogenization (HPH) treatment was examined by investigating the sludge solid reduction and organics solubilization. The sludge volatile suspended solids (VSS) decreased from 10.58 to 6.67 g/L for the sludge sample with a total solids content (TS) of 1.49% after HPH treatment at a homogenization pressure of 80 MPa with four homogenization cycles; total suspended solids (TSS) correspondingly decreased from 14.26 to 9.91 g/L. About 86.15% of the TSS reduction was attributed to the VSS reduction. The increase of homogenization pressure from 20 to 80 MPa or homogenization cycle number from 1 to 4 was favorable to the sludge organics solubilization, and the protein and polysaccharide solubilization linearly increased with the soluble chemical oxygen demand (SCOD) solubilization. More proteins were solubilized than polysaccharides. The linear relationship between SCOD solubilization and VSS reduction had no significant change under different homogenization pressures, homogenization cycles and sludge solid contents. The SCOD of 1.65 g/L was solubilized for the VSS reduction of 1.00 g/L for the three experimental sludge samples with a TS of 1.00, 1.49 and 2.48% under all HPH operating conditions. The energy efficiency results showed that the HPH treatment at a homogenization pressure of 30 MPa with a single homogenization cycle for the sludge sample with a TS of 2.48% was the most energy efficient.

BIODEGRADATION POTENTIALS OF AUTOMOBILE WORKSHOP SOIL MYCOFLORA ON FLOW STATION PETROLEUM SLUDGE WITH AN EXTRA CARBON SOURCE

OpenAIRE

Nosa Omoregbe Obayagbona; Onaiwu Idahosa Enabulele

2013-01-01

The biodegradation potentials of soil mycobiota isolated from six auto mechanic workshops and a farmland in Benin City on flow station crude oil sludge was investigated. Serial dilution and pour plate methods were utilized in the isolation and enumeration of the fungal bioload of the soil samples. The heterotrophic fungal counts ranged from 0.2×103 cfu/g to 3.2×103 cfu/g .Twenty (20) fungal species were identified from the soil samples; Aspergillus flavus, Aspergillus terreus, Aspergillus fum...

Molecular profiles of Venezuelan isolates of Trypanosoma sp. by random amplified polymorphic DNA method.

Science.gov (United States)

Perrone, T M; Gonzatti, M I; Villamizar, G; Escalante, A; Aso, P M

2009-05-12

Nine Trypanosoma sp. Venezuelan isolates, initially presumed to be T. evansi, were collected from three different hosts, capybara (Apure state), horse (Apure state) and donkey (Guarico state) and compared by the random amplification polymorphic DNA technique (RAPD). Thirty-one to 46 reproducible fragments were obtained with 12 of the 40 primers that were used. Most of the primers detected molecular profiles with few polymorphisms between the seven horse, capybara and donkey isolates. Quantitative analyses of the RAPD profiles of these isolates revealed a high degree of genetic conservation with similarity coefficients between 85.7% and 98.5%. Ten of the primers generated polymorphic RAPD profiles with two of the three Trypanosoma sp. horse isolates, namely TeAp-N/D1 and TeGu-N/D1. The similarity coefficient between these two isolates and the rest, ranged from 57.9% to 68.4% and the corresponding dendrogram clustered TeAp-N/D1 and Te Gu-N/D1 in a genetically distinct group.

Clostridium thiosulfatireducens sp. nov., a proteolytic, thiosulfate- and sulfur-reducing bacterium isolated from an upflow anaerobic sludge blanket (UASB) reactor.

Science.gov (United States)

Hernández-Eugenio, Guadalupe; Fardeau, Marie-Laure; Cayol, Jean-Luc; Patel, Bharat K C; Thomas, Pierre; Macarie, Hervé; Garcia, Jean-Louis; Ollivier, Bernard

2002-09-01

A strictly anaerobic, gram-positive, sporulating rod (0.5-0.6 x 2.0-4.0 microm), designated strain Lup 21T, was isolated from an upflow anaerobic sludge blanket (UASB) reactor treating cheese-factory wastewater. Strain Lup 21T was motile by means of peritrichous flagella, had a G+C content of 31.4 mol% and grew optimally at 37 degrees C, pH 7.4, in the absence of NaCl. It is a heterotrophic micro-organism, utilizing proteinaceous compounds (gelatin, peptides, Casamino acids and various single amino acids) but unable to use any of the carbohydrates tested as a carbon and energy source. It reduced thiosulfate and elemental sulfur to sulfide in the presence of Casamino acids as carbon and energy sources. Acetate, butyrate, isobutyrate, isovalerate, CO2 and sulfide were end products from oxidation of gelatin and Casamino acids in the presence of thiosulfate as an electron acceptor. In the absence of thiosulfate, serine, lysine, methionine and histidine were fermented. On the basis of 16S rRNA similarity, strain Lup 21T was related to members of the low-G+C Clostridiales group, Clostridium subterminale DSM 6970T being the closest relative (with a sequence similarity of 99.4%). DNA-DNA hybridization was 56% with this species. On the basis of phenotypic, genotypic and phylogenetic characteristics, the isolate was designated as a novel species of the genus Clostridium, Clostridium thiosulfatireducens sp. nov. The type strain is strain Lup 21T (= DSM 13105T = CIP 106908T).

Energy and resource utilization of deinking sludge pyrolysis

International Nuclear Information System (INIS)

Lou, Rui; Wu, Shubin; Lv, Gaojin; Yang, Qing

2012-01-01

The thermochemical conversion technique was applied in deinking sludge from the pulp and papermaking industrial to indagate the utilization of sludge biomass to energy, and the pyrolysis characteristics and pyrolytic products of deinking sludge were studied with thermogravimetric analysis (TGA) and pyrolysis coupled with gas chromatograph–mass spectrometer (Py-GC/MS). The static tubular furnace as an applied industrial research was used to study deinking sludge pyrolysis. The solid, gas and liquid of products was characterized by electron probe microanalysis (EPMA), gas chromatograph (GC) and gas chromatograph–mass (GC/MS), respectively. The results revealed that the weight-loss process of deinking sludge was a non-isothermal reaction and composed of four stages, i.e. dewater stage, volatile releasing stage, carbon burnout stage and some calcium carbonate decomposition. Pyrolytic products from deinking sludge in the static tubular furnace were comprised of the gaseous (29.78%), condensed liquid (bio-oil, 24.41%) and solid residues (45.81%). The volatiles from deinking sludge pyrolyzing were almost aromatic hydrocarbons, i.e. styrene, toluene and benzene and few acids and the solid was calcium carbonate (CaCO 3 ) that can be reused as paper filler. Deinking sludge was converted into high-grade fuel and chemicals by means of thermochemical conversion techniques, hence, pyrolysis of paper deinking sludge had a promising development on the comprehensive utilization.

Rheology of Savannah River Site Tank 51 HLW radioactive sludge

International Nuclear Information System (INIS)

Ha, B.C.

1993-01-01

Savannah River Site (SRS) Tank 51 HLW radioactive sludge represents a major portion of the first batch of sludge to be vitrified in the Defense Waste Processing Facility (DWPF) at SRS. The rheological properties of Tank 51 sludge will determine if the waste sludge can be pumped by the current DWPF process cell pump design and the homogeneity of melter feed slurries. The rheological properties of Tank 51 sludge and sludge/frit slurries at various solids concentrations were measured remotely in the Shielded Cells Operations (SCO) at the Savannah River Technology Center (SRTC) using a modified Haake Rotovisco viscometer system. Rheological properties of Tank 51 radioactive sludge/Frit 202 slurries increased drastically when the solids content was above 41 wt %. The yield stresses of Tank 51 sludge and sludge/frit slurries fall within the limits of the DWPF equipment design basis. The apparent viscosities also fall within the DWPF design basis for sludge consistency. All the results indicate that Tank 51 waste sludge and sludge/frit slurries are pumpable throughout the DWPF processes based on the current process cell pump design, and should produce homogeneous melter feed slurries

Reduction of excess sludge production using mechanical disintegration devices.

Science.gov (United States)

Strünkmann, G W; Müller, J A; Albert, F; Schwedes, J

2006-01-01

The usability of mechanical disintegration techniques for the reduction of excess sludge production in the activated sludge process was investigated. Using three different disintegration devices (ultrasonic homogeniser, stirred media mill, high pressure homogeniser) and different operational parameters of the disintegration, the effect of mechanical disintegration on the excess sludge production and on the effluent quality was studied within a continuously operated, laboratory scale wastewater treatment system with pre-denitrification. Depending on the operational conditions and the disintegration device used, a reduction of excess sludge production of up to 70% was achieved. A combination of mechanical disintegration with a membrane bioreactor process with high sludge age is more energy effective concerning reduction of sludge production than with a conventional activated sludge process at lower sludge ages. Depending on the disintegration parameters, the disintegration has no, or only minor, negative effect on the soluble effluent COD and on the COD-removal capacity of the activated sludge process. Nitrogen-removal was slightly deteriorated by the disintegration, whereas the system used was not optimised for nitrogen removal before disintegration was implemented.

Enhancement of ultrasonic disintegration of sewage sludge by aeration.

Science.gov (United States)

Zhao, He; Zhang, Panyue; Zhang, Guangming; Cheng, Rong

2016-04-01

Sonication is an effective way for sludge disintegration, which can significantly improve the efficiency of anaerobic digestion to reduce and recycle use of sludge. But high energy consumption limits the wide application of sonication. In order to improve ultrasonic sludge disintegration efficiency and reduce energy consumption, aeration was introduced. Results showed that sludge disintegration efficiency was improved significantly by combining aeration with ultrasound. The aeration flow rate, gas bubble size, ultrasonic density and aeration timing had impacts on sludge disintegration efficiency. Aeration that used in later stage of ultrasonic irradiation with low aeration flow rate, small gas bubbles significantly improved ultrasonic disintegration sludge efficiency. At the optimal conditions of 0.4 W/mL ultrasonic irradiation density, 30 mL/min of aeration flow rate, 5 min of aeration in later stage and small gas bubbles, ultrasonic sludge disintegration efficiency was increased by 45% and one third of ultrasonic energy was saved. This approach will greatly benefit the application of ultrasonic sludge disintegration and strongly promote the treatment and recycle of wastewater sludge. Copyright © 2015. Published by Elsevier B.V.

ALARA ASSESSMENT OF SETTLER SLUDGE SAMPLING METHODS

International Nuclear Information System (INIS)

Nelsen, L.A.

2009-01-01

The purpose of this assessment is to compare underwater and above water settler sludge sampling methods to determine if the added cost for underwater sampling for the sole purpose of worker dose reductions is justified. Initial planning for sludge sampling included container, settler and knock-out-pot (KOP) sampling. Due to the significantly higher dose consequence of KOP sludge, a decision was made to sample KOP underwater to achieve worker dose reductions. Additionally, initial plans were to utilize the underwater sampling apparatus for settler sludge. Since there are no longer plans to sample KOP sludge, the decision for underwater sampling for settler sludge needs to be revisited. The present sampling plan calls for spending an estimated $2,500,000 to design and construct a new underwater sampling system (per A21 C-PL-001 RevOE). This evaluation will compare and contrast the present method of above water sampling to the underwater method that is planned by the Sludge Treatment Project (STP) and determine if settler samples can be taken using the existing sampling cart (with potentially minor modifications) while maintaining doses to workers As Low As Reasonably Achievable (ALARA) and eliminate the need for costly redesigns, testing and personnel retraining

ALARA ASSESSMENT OF SETTLER SLUDGE SAMPLING METHODS

Energy Technology Data Exchange (ETDEWEB)

NELSEN LA

2009-01-30

The purpose of this assessment is to compare underwater and above water settler sludge sampling methods to determine if the added cost for underwater sampling for the sole purpose of worker dose reductions is justified. Initial planning for sludge sampling included container, settler and knock-out-pot (KOP) sampling. Due to the significantly higher dose consequence of KOP sludge, a decision was made to sample KOP underwater to achieve worker dose reductions. Additionally, initial plans were to utilize the underwater sampling apparatus for settler sludge. Since there are no longer plans to sample KOP sludge, the decision for underwater sampling for settler sludge needs to be revisited. The present sampling plan calls for spending an estimated $2,500,000 to design and construct a new underwater sampling system (per A21 C-PL-001 RevOE). This evaluation will compare and contrast the present method of above water sampling to the underwater method that is planned by the Sludge Treatment Project (STP) and determine if settler samples can be taken using the existing sampling cart (with potentially minor modifications) while maintaining doses to workers As Low As Reasonably Achievable (ALARA) and eliminate the need for costly redesigns, testing and personnel retraining.

Deep Sludge Gas Release Event Analytical Evaluation

International Nuclear Information System (INIS)

Sams, Terry L.

2013-01-01

Long Abstract. Full Text. The purpose of the Deep Sludge Gas Release Event Analytical Evaluation (DSGRE-AE) is to evaluate the postulated hypothesis that a hydrogen GRE may occur in Hanford tanks containing waste sludges at levels greater than previously experienced. There is a need to understand gas retention and release hazards in sludge beds which are 200 -300 inches deep. These sludge beds are deeper than historical Hanford sludge waste beds, and are created when waste is retrieved from older single-shell tanks (SST) and transferred to newer double-shell tanks (DST).Retrieval of waste from SSTs reduces the risk to the environment from leakage or potential leakage of waste into the ground from these tanks. However, the possibility of an energetic event (flammable gas accident) in the retrieval receiver DST is worse than slow leakage. Lines of inquiry, therefore, are (1) can sludge waste be stored safely in deep beds; (2) can gas release events (GRE) be prevented by periodically degassing the sludge (e.g., mixer pump); or (3) does the retrieval strategy need to be altered to limit sludge bed height by retrieving into additional DSTs? The scope of this effort is to provide expert advice on whether or not to move forward with the generation of deep beds of sludge through retrieval of C-Farm tanks. Evaluation of possible mitigation methods (e.g., using mixer pumps to release gas, retrieving into an additional DST) are being evaluated by a second team and are not discussed in this report. While available data and engineering judgment indicate that increased gas retention (retained gas fraction) in DST sludge at depths resulting from the completion of SST 241-C Tank Farm retrievals is not expected and, even if gas releases were to occur, they would be small and local, a positive USQ was declared (Occurrence Report EM-RP--WRPS-TANKFARM-2012-0014, 'Potential Exists for a Large Spontaneous Gas Release Event in Deep Settled Waste Sludge'). The purpose of this technical

Molecular analysis of Leptospira spp. isolated from humans by restriction fragment length polymorphism, real-time PCR and pulsed-field gel electrophoresis.

Science.gov (United States)

Turk, Nenad; Milas, Zoran; Mojcec, Vesna; Ruzic-Sabljic, Eva; Staresina, Vilim; Stritof, Zrinka; Habus, Josipa; Postic, Daniele

2009-11-01

A total of 17 Leptospira clinical strains isolated from humans in Croatia were serologically and genetically analysed. For serovar identification, the microscopic agglutination test (MAT) and pulsed-field gel electrophoresis (PFGE) were used. To identify isolates on genomic species level, PCR-based restriction fragment length polymorphism (RFLP) and real-time PCR were performed. MAT revealed the following serogroup affinities: Grippotyphosa (seven isolates), Icterohaemorrhagiae (eight isolates) and Javanica (two isolates). RFLP of PCR products from a 331-bp-long fragment of rrs (16S rRNA gene) digested with endonucleases MnlI and DdeI and real-time PCR revealed three Leptospira genomic species. Grippotyphosa isolates belonged to Leptospira kirschneri, Icterohaemorrhagiae isolates to Leptospira interrogans and Javanica isolates to Leptospira borgpetersenii. Genomic DNA from 17 leptospiral isolates was digested with NotI and SgrAI restriction enzymes and analysed by PFGE. Results showed that seven isolates have the same binding pattern to serovar Grippotyphosa, eight isolates to serovar Icterohaemorrhagiae and two isolates to serovar Poi. Results demonstrate the diversity of leptospires circulating in Croatia. We point out the usefulness of a combination of PFGE, RFLP and real-time PCR as appropriate molecular methods in molecular analysis of leptospires.

Processing method for radioactive sludge

International Nuclear Information System (INIS)

Shoji, Yuichi; Kaneko, Masaaki.

1993-01-01

The concentration of radioactive sludges contained in a storage tank is controlled, thereafter, a filter is charged into a processing vessel to continuously conduct dewatering. Then, the radioactive sludges and an oxidizer are mixed by stirring using a stirring impeller and by vibrations using a vibrator. At the same time, thermic rays are irradiated by using infrared ray lamps to heat and decompose them. Since thermic rays reach the center of the radioactive sludges by the infrared ray lamps, ion exchange resins are sufficiently decomposed and carbonized into inorganic material. Then, a filling hardener such as mortar cement having a good flowability is charged to solidify the wastes. With such procedures, radioactive sludges can be stored under a stable condition for a long period of time by decomposing organic materials into inorganic materials and solidifying them. Further, an operator's radiation exposure dose can remarkably be reduced by applying a predetermined and a stabilization treatment in an identical processing vessel. (N.H.)

Synchronous municipal sewerage-sludge stabilization.

Science.gov (United States)

Bukuru, Godefroid; Jian, Yang

2005-01-01

A study on a pilot plant accomplishing synchronous municipal sewerage-sludge stabilization was conducted at a municipal sewerage treatment plant. Stabilization of sewerage and sludge is achieved in three-step process: anaerobic reactor, roughing filter and a microbial-earthworm-ecofilter. The integrated ecofilter utilizes an artificial ecosystem to degrade and stabilize the sewerage and sludge. When the hydraulic retention time(HRT) of the anaerobic reactor is 6 h, the hydraulic load(HL) of the bio-filter is 16 m3/(m2 x d), the HL of the eco-filter is 5 m3/(m2 x d), the recycle ratio of nitrified liquor is 1.5, the removal efficiency is 83%-89% for COD(Cr), 94%-96% for BOD5, 96%-98% for SS, and 76%-95% for NH3-N. The whole system realizes the zero emission of sludge, and has the characteristics of saving energy consumption and operational costs.

Reasonable management plan of sludge in sewage disposal plant

Energy Technology Data Exchange (ETDEWEB)

Yum, Kyu Jin; Koo, Hyun Jung [Korea Environment Institute, Seoul (Korea)

1998-12-01

The compost method, which is widely used as a sewage disposal recycling in Korea, is now basically impossible to recycle sludge to compost by the Ministry of Agriculture and Forestry announcement. Therefore, the disposal of sludge will be much harder with reducing the amount of sludge used as compost. The amount of sludge other than using as compost is very small, so the development of various sludge recycling and use will be needed with regulations. This study was implemented to help the establishment of sewage sludge recycling policy in Korea. 30 refs., 17 figs., 58 tabs.

Molecular Characterisation of Salmonella enterica Serovar Typhi Isolated from Typhoidial Humans

Directory of Open Access Journals (Sweden)

Arunava Das

2012-09-01

Full Text Available Aims: Salmonella enterica serovar Typhi is the major causative agent for typhoidial fever around the globe among human population reported till date. Present research work was carried out for detection and molecular characterisation of Salmonella enterica serovar Typhi isolated from humans with Typhoidial fever by biochemical, phenotypical and virulence gene based polymerase chain reaction (PCR techniques. The isolated strains were also investigated for antibiotic susceptibility patterns as a control measure. Methodology and Results: A total of 16 clinical samples were collected from the same numbers of patients (7 males and 9 females from Coimbatore, Erode and Salem districts of Tamil Nadu and were processed via broth enrichment methods for isolation and identification of the causative agent S. enterica serovar Typhi. Microbiological and biochemical investigations revealed the presence of S. Typhi from 16 samples. The biotyping of the isolates showed that all the isolates belonged to biotype IV. The PCR analysis confirmed the presence of invA (Invasion gene, 244bp, tyv (Tyveloseepimerase gene, 615 bp, fliC-d (Phage-1 flagellin gene for d-antigen, 750 bp and viaB (Vi antigen gene, 439bp in all 16 clinical samples. The antibiotic susceptibility test that was carried out among the isolates against 12 antimicrobial agents, showed 100 % resistance to only ampicillin and 100 % sensitivity to carbenicillin, chloramphenicol, clindamycin, gentamycin, kanamycin and tetracycline.Conclusion, significance and impact of study: This study confirmed the association of virulent strains of S. enterica serovar Typhi from Typhoidial fever among human population and suggested that PCR based diagnostic could be very useful for the rapid detection of S. Typhi isolates. Present study emphasized the use of antibiotic like chloramphenicol or in combination with other antibiotics for the effective control of S. Typhi.

Molecular docking for thrombolytic activity of some isolated compounds from Clausena lansium.

Directory of Open Access Journals (Sweden)

Arkajyoti Paul

2017-03-01

Full Text Available Clausena lansium (Family- Rutaceae is commonly known as wampee, is found in fallow lands throughout Bangladesh. Our aim of the study to performed molecular docking studies to identify potential binding affinities of the phytocompounds from Clausena lansium, namely Clausemarin B, Clausenaline C, Clausenaline E, Murrayanine, vanillic acid and Xanthotoxol for searching of lead molecule for thrombolytic activity. A wide range of docking score found during molecular docking by Schrodinger. Clausemarin B , Clausenaline C , Clausenaline E, Murrayanine , vanillic acid and Xanthotoxol showed the docking score -6.926, -4.041, -4.889 , -4.356, -3.007 and -5.816 respectively. Among all the compounds Clausemarin B showed the best docking score. So, Clausemarin B is the best compounds for thrombolytic activity, as it possessed the best value in Molecular docking. Further in vivo investigation need to identify the thrombolytic activity of isolated compounds from Clausena lansium.

Sampling and analyses of SRP high-level waste sludges

International Nuclear Information System (INIS)

Stone, J.A.; Kelley, J.A.; McMillan, T.S.

1976-08-01

Twelve 3-liter samples of high-heat waste sludges were collected from four Savannah River Plant waste tanks with a hydraulically operated sample collector of unique design. Ten of these samples were processed in Savannah River Laboratory shielded cell facilities, yielding 5.3 kg of washed, dried sludge products for waste solidification studies. After initial drying, each batch was washed by settling and decantation to remove the bulk of soluble salts and then was redried. Additional washes were by filtration, followed by final drying. Conclusions from analyses of samples taken during the processing steps were: (a) the raw sludges contained approximately 80 wt percent soluble salts, most of which were removed by the washes; (b) 90 Sr and 238 , 239 Pu remained in the sludges, but most of the 137 Cs was removed by washing; (c) small amounts of sodium, sulfate, and 137 Cs remained in the sludges after thorough washing; (d) no significant differences were found in sludge samples taken from different risers of one waste tank. Chemical and radiometric compositions of the sludge product from each tank were determined. The sludges had diverse compositions, but iron, manganese, aluminum, and uranium were principal elements in each sludge. 90 Sr was the predominant radionuclide in each sludge product

Reuse of industrial sludge as construction aggregates.

Science.gov (United States)

Tay, J H; Show, K Y; Hong, S Y

2001-01-01

Industrial wastewater sludge and dredged marine clay are high volume wastes that needed enormous space at landfill disposal sites. Due to the limitation of land space, there is an urgent need for alternative disposal methods for these two wastes. This study investigates the possibility of using the industrial sludge in combination with marine clay as construction aggregates. Different proportions of sludge and clay were made into round and angular aggregates. It was found that certain mix proportions could provide aggregates of adequate strength, comparable to that of conventional aggregates. Concrete samples cast from the sludge-clay aggregates yield compressive strengths in the range of 31.0 to 39.0 N/mm2. The results showed that the round aggregates of 100% sludge and the crush aggregates of sludge with up to 20% clay produced concrete of compressive strengths which are superior to that of 38.0 N/mm2 for conventional aggregate. The study indicates that the conversion of high volume wastes into construction materials is a potential option for waste management.

Solidifying power station resins and sludges

International Nuclear Information System (INIS)

Willis, A.S.D.; Haigh, C.P.

1984-01-01

Radioactive ion exchange resins and sludges arise at nuclear power stations from various operations associated with effluent treatment and liquid waste management. As the result of an intensive development programme, the Central Electricity Generating Board (CEGB) has designed a process to convert power station resins and sludges into a shielded, packaged solid monolithic form suitable for final disposal. Research and development, the generic CEGB sludge/resin conditioning plant and the CEGB Active Waste Project are described. (U.K.)

Analysis of Organic and Inorganic Contaminants in Dried Sewage Sludge and By-Products of Dried Sewage Sludge Gasification

Directory of Open Access Journals (Sweden)

Sebastian Werle

2014-01-01

Full Text Available Organic and inorganic contaminants in sewage sludge may cause their presence also in the by-products formed during gasification processes. Thus, this paper presents multidirectional chemical instrumental activation analyses of dried sewage sludge as well as both solid (ash, char coal and liquid (tar by-products formed during sewage gasification in a fixed bed reactor which was carried out to assess the extent of that phenomenon. Significant differences were observed in the type of contaminants present in the solid and liquid by-products from the dried sewage sludge gasification. Except for heavy metals, the characteristics of the contaminants in the by-products, irrespective of their form (solid and liquid, were different from those initially determined in the sewage sludge. It has been found that gasification promotes the migration of certain valuable inorganic compounds from sewage sludge into solid by-products which might be recovered. On the other hand, the liquid by-products resulting from sewage sludge gasification require a separate process for their treatment or disposal due to their considerable loading with toxic and hazardous organic compounds (phenols and their derivatives.

Dewaterability of sludge digested in extended aeration plants using ...

African Journals Online (AJOL)

Dewaterability of unconditioned sludge digested in full scale and lab scale experiments using either extended aeration (EA) or anaerobic digestion were compared on full and lab scale sand drying beds. Sludge digested in EA plants resulted in improvement in sludge dewaterability compared to sludge digested ...

Isolation, molecular identification and quinolone-susceptibility testing of Arcobacter spp. isolated from fresh vegetables in Spain.

Science.gov (United States)

González, Ana; Bayas Morejón, Isidro Favián; Ferrús, María Antonia

2017-08-01

Some species of the Arcobacter genus are considered emerging foodborne and waterborne enteropathogens. However, the presence of Arcobacter spp. in vegetables very little is known, because most studies have focused on foods of animal origin. On the other hand, quinolones are considered as first-line drugs for the treatment of infection by campylobacteria in human patients, but few data are currently available about the resistance levels to these antibiotics among Arcobacter species. Therefore, the aim of this study was to investigate the presence and diversity of arcobacters isolated from fresh vegetables such as lettuces, spinaches, chards and cabbages. Resistance to quinolones of the isolates was also investigated. One hundred fresh vegetables samples purchased from seven local retail markets in Valencia (Spain) during eight months were analysed. The study included 41 lettuces, 21 spinaches, 34 chards and 4 cabbages. Samples were analysed by culture and by molecular methods before and after enrichment. By culture, 17 out of 100 analysed samples were Arcobacter positive and twenty-five isolates were obtained from them. Direct detection by PCR was low, with only 4% Arcobacter spp. positive samples. This percentage increased considerably, up 20%, after 48 h enrichment. By polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP), 17 out of the 25 isolates were identified as A. butzleri and 8 as A. cryaerophilus. Only two A. butzleri isolates showed resistance to levofloxacin and ciprofloxacin. The sequencing of a fragment of the QRDR region of the gyrA gene from the quinolones-resistant isolates revealed the presence of a mutation in position 254 of this gene (C-T transition). This study is the first report about the presence of pathogenic species of Arcobacter spp. in chards and cabbages and confirms that fresh vegetables can act as transmission vehicle to humans. Moreover, the presence of A. butzleri quinolone resistant in vegetables could

Anaerobic digestion of cheese whey using an upflow anaerobic sludge blanket reactor: Pt. 3; Sludge and substrate profiles

Energy Technology Data Exchange (ETDEWEB)

Yan, J.Q.; Lo, K.V.; Liao, P.H. (British Columbia Univ., Vancouver (CA). Dept. of Bio-Resource Engineering)

1990-01-01

Anaerobic treatment of cheese whey using a 17.5 litre upflow anaerobic sludge blanket reactor was investigated in the laboratory over a range of influent concentration from 4.5 to 38.1 g COD litre{sup -1} at a constant hydraulic retention time of 5 days. The results indicated that two sludge distribution regions, a sludge bed and a sludge blanket, as well as two distinct reaction phases, acidogenic and methanogenic, were formed. However, as the substrate loading was increased, the acidogenic region extended into the methanogenic region in the upper portion of the reactor until the whole region was acidogenic, leading to the failure of the reactor. (author).

Molecular Characterization of Multidrug Resistant Uropathogenic E. Coli Isolates from Jordanian Patients.

Science.gov (United States)

Nairoukh, Yacoub R; Mahafzah, Azmi M; Irshaid, Amal; Shehabi, Asem A

2018-01-01

Emergence of multi-drug resistant uropathogenic E. coli strains is an increasing problem to empirical treatment of urinary tract infections in many countries. This study investigated the magnitude of this problem in Jordan. A total of 262 E. coli isolates were recovered from urine samples of Jordanian patients which were suspected to have urinary tract infections (UTIs). All isolates were primarily identified by routine biochemical tests and tested for antimicrobial susceptibility by disc diffusion method. Fifty representative Multidrug Resistance (MDR) E. coli isolates to 3 or more antibiotic classes were tested for the presence of resistance genes of blaCTX-M- 1, 9 and 15, carbapenemase ( blaIMP, blaVIM, blaNDM-1, blaOXA-48 ), fluoroquinolones mutated genes ( parC and gyrA ) and clone of ST131 type using PCR methods. A total of 150/262 (57.3%) of E. coli isolates were MDR. Urine samples of hospitalized patients showed significantly more MDR isolates than outpatients. Fifty representative MDR E. coli isolates indicated the following molecular characteristics: All were positive for mutated parC gene and gyrA and for ST131 clone, and 78% were positive for genes of CTX-M-15 , 76% for CTX-M-I and for 8% CTX-M-9 , respectively. Additionally, all 50 MDR E. coli isolates were negative for carbapenemase genes ( blaIMP, blaVIM, blaNDM-1, blaOXA-48 ), except of one isolate was positive for blaKPC-2 . This study indicates alarming high rates recovery of MDR uropathogenic E. coli from Jordanian patients associated with high rates of positive ST131 clone, fluoroquinolone resistant and important types of blaCTX-M.

Economic assessment of biodiesel production from wastewater sludge.

Science.gov (United States)

Chen, Jiaxin; Tyagi, Rajeshwar Dayal; Li, Ji; Zhang, Xiaolei; Drogui, Patrick; Sun, Feiyun

2018-04-01

Currently, there are mainly two pathways of the biodiesel production from wastewater sludge including 1) directly extracting the lipid in sludge and then converting the lipid to biodiesel through trans-esterification, and 2) employing sludge as medium to cultivate oleaginous microorganism to accumulate lipid and then transferring the lipid to biodiesel. So far, the study was still in research stage and its cost feasibility was not yet investigated. In this study, biodiesel production from wastewater sludge was designed and the cost was estimated with SuperPro Designer. With consideration of converting the lipid in raw sludge to biodiesel, the unit production cost was 0.67 US $/kg biodiesel (0.59 US $/L biodiesel). When the sludge was used as medium to grow oleaginous microorganism to accumulate lipid for producing biodiesel, the unit production cost was 1.08 US $/kg biodiesel (0.94 US $/L biodiesel). The study showed that sludge has great potential in biodiesel production. Copyright © 2018 Elsevier Ltd. All rights reserved.

Radioactive contamination of sewage sludge. Preliminary data

Energy Technology Data Exchange (ETDEWEB)

Soeder, C J; Zanders, E; Raphael, T

1986-01-01

Because of the radioactivity released through the explosion of the nuclear reactor near Chernobyl radionuclides have been accumulated to a significant extent in sewage sludge in the Federal Republic of Germany. This is demonstrated for samples from four activated sludge plants according to a recent recommendation of the German Commission for Radiation Protection, there is until now no reason to deviate from the common practices of sludge disposal or incineration. The degree of radioactive contamination of plant materials produced on farm lands on which sewage sludge is being spread cannot be estimated with sufficient certainty yet. Additional information is required.

Where to dispose of the sewage sludge?

International Nuclear Information System (INIS)

Beurer, P.; Geering, F.

2001-01-01

The 'proper' course for the disposal of sewage sludge is a topic that has continually sparked intense discussion for years. New legal regulations have developed which have significantly changed the disposal structure. Nevertheless, the consumer market of agriculture products has an increasing influence on sewage sludge recycling possibilities. In this report, the changes in sewage sludge disposal within the last ten years and the expected development is pointed out. On account of legal guidelines and of political market influences, the thermal recycling of sewage sludge is considered as the future solution, which should, however, be adapted according to marginal situations. (author)

Sewage sludge - What can be done with it?

International Nuclear Information System (INIS)

Beurer, P.; Geering, F.

2002-01-01

This article presents a review of the state-of-the-art in the disposal of the sewage sludge that is left over after treatment of wastewater. Also, developments over the past ten years both in market structures and in legislation are discussed and future developments are reviewed. On account of legislation and political influences on the market, the thermal exploitation of sewage sludge is looked at in depth. The ecological and economic aspects of sewage sludge disposal are examined and the costs of different methods of sewage sludge treatment are compared. Various methods of disposal including dumping, composting, incineration in cement ovens, coal-fired power stations and waste incineration facilities are discussed, as is burning in special sludge incineration plant. A prognosis is made on the development of sewage sludge quantities for Germany, Switzerland and Austria over the next years

Roseomonas chloroacetimidivorans sp. nov., a chloroacetamide herbicide-degrading bacterium isolated from activated sludge.

Science.gov (United States)

Chu, Cui-Wei; Chen, Qing; Wang, Cheng-Hong; Wang, Hong-Mei; Sun, Zhong-Guan; He, Qin; He, Jian; Gu, Jin-Gang

2016-05-01

A Gram-negative, aerobic, short rod-shaped, pink-pigmented, non-motile bacterium, designated BUT-13(T), was isolated from activated sludge of an herbicide-manufacturing wastewater treatment facility in Jiangsu province, China. Growth was observed at 0-5.5 % NaCl, pH 6.0-9.0 and 12-37 °C. Phylogenetic analysis based on 16S rRNA gene sequences indicated that strain BUT-13(T) is a member of the genus Roseomonas, and shows high sequence similarities to R. pecuniae N75(T) (98.0 %) and R. rosea 173-96(T) (97.5 %), and lower (<97 %) sequence similarities to all other Roseomonas species. Chemotaxonomic analysis revealed that strain BUT-13(T) possesses Q-10 as the predominant ubiquinone; summed feature 8 (C18:1 w7c and/or C18:1 w6c; 38.8 %), C18:0 (16.6 %), C16:0 (15.2 %), summed feature 3 (C16:1 ω6c and/or C16:1 ω7; 7.9 %) and C18:1 w9c (4.7 %) as the major fatty acids. The polar lipids were found to consist of two aminolipids, a glycolipid, a phospholipid, a phosphoglycolipid, phosphatidylcholine, phosphatidylethanolamine and diphosphatidylglycerol. Strain BUT-13(T) showed low DNA-DNA relatedness with R. pecuniae N75(T) (45.2 %) and R. rosea 173-96(T) (51.2 %). The DNA G+C content was determined to be 67.6 mol%. Based on the phylogenetic analysis, DNA-DNA hybridization and chemotaxonomic analysis, as well as biochemical characteristics, strain BUT-13(T) can be clearly distinguished from all currently recognised Roseomonas species and should be classified as a novel species of the genus Roseomonas, for which the name Roseomonas chloroacetimidivorans sp. nov. is proposed. The type strain is BUT-13(T) (CCTCC AB 2015299(T) = JCM 31050(T)).

Irradiation treatment of sewage sludge: History and prospects

International Nuclear Information System (INIS)

Bao Borong; Wu Minghong; Zhou Ruimin; Zhu Jinliang

1998-01-01

This paper first reviews the history of irradiation treatment of sewage sludge in the world. The first sludge irradiation plant was built in Geiselbullach, West Germany in 1973 and used 60 Co as irradiation source. Since then, many sludge irradiators were constructed in U.S.A., India, Japan, Canada, Poland, etc., which used 60 Co, 137 Cs or electron beam as irradiation sources. The paper then describes some basic research on irradiation treatment of sewage sludge including optimization of irradiation parameters, synergistic effect of radiation with heat, oxygenation, irradiation-composting and potential applications of treated sludge. Some proposals have been suggested for further development of this technology in the future

The hydraulic transportation of thickened sludges

African Journals Online (AJOL)

driniev

non-Newtonian sludges (Xu et al., 1993; Spinosa and Lotita, 2001; .... [11]. Analysis and typical applications. Laminar/turbulent transition. For most sewage sludges the ... on Transport and Sedimentation of Solid Particles - Ghent, September.

Effects of Sewage Sludges Contaminated with Chlorinated Aromatic Hydrocarbons on Sludge-Treated Areas (Soils and Sediments

Directory of Open Access Journals (Sweden)

Ethel Eljarrat

2002-01-01

Full Text Available The fate of PCDDs, PCDFs, and PCBs in sewage sludges after different management techniques — such as agricultural application, land restoration, and marine disposal — was studied. Changes observed in the concentrations, in the ratio between PCDD and PCDF levels, and in the isomeric distribution suggest the influence of the sewage sludge on the sludge-treated areas (soils and sediments. Whereas land application techniques seem to produce no serious environmental consequences, marine disposal practices produce considerable increases in the levels of contamination in marine sediments.

Molecular identification of fungal isolates and hatching success of green turtle (Chelonia mydas) nests.

Science.gov (United States)

Candan, Esra Deniz

2018-02-26

The aim of this study is to investigate the fungal diversity of green turtle nests and to examine phylogenetic relationships among these isolates. During the nesting season, samples of intra-nest sand and failed eggs were collected from 25% of the surviving nests in Sugözü Beaches, which are amongst the most important nesting beaches for endangered green turtles in the Mediterranean. Twenty-three fungi were identified by molecular techniques. Fungal isolates belonged to genera Aspergillus, Emericella, Rhizopus, Actinomucor and Apophysomyces with two undescribed species. Aspergillus variecolor, Aspergillus quadrilinieatus, Aspergillus tubingensis, Rhizopus oryzae, Actinomucor elegans and Apophysomyces variabilis were firstly detected in all sea turtle nests within this study. Our results demonstrate that 36.4% of the nests had fungal contamination. Also hatching success of the nests contaminated by fungi were significantly lower than the uncontaminated nests (P = 0.029). Also, this may represent a threat to marine turtles and a risk for the health of conservation workers. This study is the first molecular phylogenetic study associated with sea turtle nests in the eastern Mediterranean coast and contributes to the wider body of literature on fungal invasion of sea turtle nests with firstly isolated species. These findings are important for improving potential conservation measures for the nest sites.

Two-phase anaerobic digestion of partially acidified sewage sludge: a pilot plant study for safe sludge disposal in developing countries.

Science.gov (United States)

Passio, Luca; Rizzoa, Luigi; Fuchs, Stephan

2012-09-01

The unsafe disposal of wastewater and sludge in different areas of developing countries results in significant environmental pollution, particularly for groundwater, thus increasing the risk of waterborne diseases spreading. In this work, a two-phase anaerobic digestion process for post-treatment of partially acidified sewage sludge was investigated to evaluate its feasibility as a safe sludge disposal system. Pilot tests showed that an effective sludge stabilization can be achieved (total volatile solids content <65%, organic acid concentration <200 mg/L at flow rate = 50 L/d and hydraulic residence time = 18 d) as well as a relative low faecal coliform density (<1000 most probable number per g total solids), showing that land application of the sludge without restrictions is possible according to US Environmental Protection Agency criteria for safe sludge disposal. A biogas production as high as 390 L/d with a 60% methane content by volume was achieved, showing that energy production from biogas may be achieved as well.

Wastewater and sludge management and research in Oman: An overview.

Science.gov (United States)

Jaffar Abdul Khaliq, Suaad; Ahmed, Mushtaque; Al-Wardy, Malik; Al-Busaidi, Ahmed; Choudri, B S

2017-03-01

It is well recognized that management of wastewater and sludge is a critical environmental issue in many countries. Wastewater treatment and sludge production take place under different technical, economic, and social contexts, thus requiring different approaches and involving different solutions. In most cases, a regular and environmentally safe wastewater treatment and associated sludge management requires the development of realistic and enforceable regulations, as well as treatment systems appropriate to local circumstances. The main objective of this paper is to provide useful information about the current wastewater and sludge treatment, management, regulations, and research in Oman. Based on the review and discussion, the wastewater treatment and sludge management in Oman has been evolving over the years. Further, the land application of sewage sludge should encourage revision of existing standards, regulations, and policies for the management and beneficial use of sewage sludge in Oman. Wastewater treatment and sludge management in Oman have been evolving over the years. Sludge utilization has been a challenge due to its association with human waste. Therefore, composting of sewage sludge is the best option in agriculture activities. Sludge and wastewater utilization can add up positively in the economic aspects of the country in terms of creating jobs and improving annual income rate. The number of research projects done on wastewater reuse and other ongoing ones related to the land application of sewage sludge should encourage revision of existing standards, regulations, and policies for the management and beneficial use of sewage sludge in Oman.

Experience with a pilot plant for the irradiation of sewage sludge: Results on the effect of differently treated sewage sludge on plants and soil

International Nuclear Information System (INIS)

Suess, A.; Rosopulo, A.; Borchert, H.; Beck, Th.; Bauchhenss, J.; Schurmann, G.

1975-01-01

Since hygienization of sewage sludge will be important for an agricultural application it is necessary to study the effect of differently treated sewage sludge on plants and soil. In bean and maize experiments in 1973 and 1974 it was found that the treatment of sewage sludge is less important than soil properties and water capacity. Analysis on the efficiency of nutrients, minor elements and heavy metals from differently treated sewage sludge to plants were performed. Microbiological greenhouse studies indicated that there is a distinct tendency for different reactions, that irradiated sewage sludge gives a slightly better effect than untreated sludge, while the heat-treated sewage sludge indicates always a decrease, especially with the increase of applied amounts (respiration, protease and nitrification). In the field experiments there were almost no differences between untreated and irradiated sewage sludge, whereas there was always a smaller microbial activity after application of heat-treated sewage sludge. Studies on soil fauna (especially on Collemboles and Oribatidae) in the field trials indicate the influences of abiotic factors on the different locations. Besides these influences there was a decrease in the number of Collemboles and mites (in comparison with a normal fertilized plot) on the plots with 800 m 3 /ha treated sewage sludge. There was a remarkably large decrease in the plots with irradiated sewage sludge after an application of 800 m 3 /ha. Depending on the soil type, physical and chemical studies indicated an increase in the effective field capacity after the application of sewage sludge, and sometimes the best effects occurred with irradiated sewage sludge. Relative high aggregate values were observed (6-2, 6-5 mm diameter) in the plots with irradiated sewage sludge. (author)

Molecular analysis of Rv0679c and Rv0180c genes of Mycobacterium tuberculosis from clinical isolates of pulmonary tuberculosis

Directory of Open Access Journals (Sweden)

L Rupa

2016-01-01

Full Text Available Context: Two novel proteins/genes Rv0679c and Rv0180c of Mycobacterium tuberculosis (MTB H37Rv were classified as a hypothetical membrane and transmembrane proteins which might have a role in the invasion. Molecular analysis of these genes in human clinical isolates of pulmonary tuberculosis (PTB patients was not well characterised. Aims: To assess the molecular diversity of Rv0679c and Rv0180c genes of MTB from clinical isolates of PTB patients. Settings and Design: DNA from 97 clinical isolates was extracted and subjected to amplification using selective primers by polymerase chain reaction (PCR. The PCR product obtained was sequenced commercially. Patients and Methods: Clinical isolates obtained from tuberculosis patients were investigated for polymorphisms in the Rv0679c and Rv0180c genes by PCR and DNA sequencing. Genomic DNA isolated by cetyltrimethylammonium bromide method was used for amplification of genes. Results: Rv0679c gene was highly conserved in 61 out of 65 clinical isolates assessed for sequence homology with wild-type H37Rv gene and was identical using ClustalW. Fifty-five out of 78 (70.5% clinical isolates assessed for Rv0180c were positive for single nucleotide polymorphism (SNP at 258th position where the nucleotide G was replaced with T (G to T. In clinical isolates of untreated cases, the frequency was 54.5% for SNP at 258th position which is low compared to cases undergoing treatment where the frequency was 73.1%. Conclusions: Molecular analysis of Rv0180c in clinical isolates of PTB assessed in this study was the first report, where an SNP at 258th position G to T was identified within the gene. Rv0679c gene was highly conserved (94%, within Indian clinical isolates as compared to reports from other nations.

Molecular Detection of Inducible Clindamycin Resistance among Staphylococcal Strains Isolated from Hospital Patients

Directory of Open Access Journals (Sweden)

Shadiyeh Abdollahi

2013-04-01

Full Text Available Background & Objectives: Macrolide, lincosamide and streptogramin B (MLSB antimicrobial agents are used in the treatment of staphylococcal infections. They prevent the microbial protein synthesis system through binding to 23 S rRNA. The aim of this study was to apply molecular methods to detect inducible clindamycin resistance genes among staphylococcal strains isolated from clinical specimens.   Methods : Two hundred staphylococcus strains were isolated from nose and throat swabs of patients in Toohid and Besat hospitals in Sanandaj . Antimicrobial susceptibilities of isolates were determined using disc diffusion method, agar screen test and D-Test. A multiplex PCR was performed using primers specific for erm (A, B, C, TR genes.   Results: Out of 200 isolates, 18.5 % were MRSA and 32% were MRCNS (methicillin resistant coagulase negative staphylococci. Of 80 erythromycin resistant isolates, 48 were coagulase negative and 32 were S. aureus. Among the 48 coagulase negative staphylococci (CONS isolates, 11.63% expressed the MLSB-inducible phenotypes. Using PCR, the frequency of different genes in the collection of isolates were as follows: ermA 5.41 % , erm B 5.41 % , and erm C 3.13%. The ermTR gene was negative in all isolates. Among the 32 S. aureus isolates, 9.38% expressed the MLSB-nducible phenotype. Using PCR, these isolates harbored erm A (2.22%, ermB (2.22%, ermC (2.22% and ermTR (2.22% .   Conclusion: This is the first study to show the rate of inducible clindamycin clinical isolates of staphylococci harboring erm genes in Sananadaj. It also demonstrated the frequency of erm genes was higher among CONS isolates than S. aureus. This data suggested the transfer of resistance gene from nonpathogenic to pathogenic strains is likely to happen. Therefore, screening and control of these resistance genes is recommended at clinical laboratories.

Molecular diversity of thermophilic bacteria isolated from Pasinler hot spring (Erzurum, Turkey)

OpenAIRE

ADIGÜZEL, Ahmet; İNAN, Kadriye; ŞAHİN, Fikrettin; ARASOĞLU, Tulin; GÜLLÜCE, Medine

2011-01-01

The present study was conducted to determine the phenotypic and genotypic characterization of thermophilic bacteria isolated from Pasinler hot spring, Erzurum, Turkey. Fatty acid profiles, BOX PCR fingerprints, and 16S rDNA sequence data were used for the phenotypic and genotypic characterization of thermophilic bacteria. Totally 9 different bacterial strains were selected based on morphological, physiological, and biochemical tests. These strains were characterized by molecular tests includi...

Recent developments in Sandia Laboratories' sewage sludge irradiation program

International Nuclear Information System (INIS)

Sivinski, H.D.; Brandon, J.R.; Morris, M.E.; Neuhauser, K.S.; Ward, R.L.; McCaslin, B.; Smith, G.S.

1977-01-01

Pathogen reduction studies show that gamma irradiation is effective in inactivating pathogenic bacteria, parasite ova, and viruses in liquid sludges. Ammonia is shown to be virucidal to poliovirus and several other enteric viruses. Sludge processing costs are relatively economical for composted or dried sludges, but only marginally competitive with costs of heat treatment for liquid sludges. Physical and chemical studies show that effects of irradiation of sludges on dewatering properties are insignificant when compared to the effects of polymer addition. Dried, irradiated undigested sludge has significant nutritional value as a feed supplement for sheep and cattle and in agronomic uses such as greenhouses and field plots. No significant harmful effects have been demonstrated in the feeding program. Product enhancement studies are under way, including schemes for removing nitrogen from wastewaters and adding it to sludges in the form of ammonium salts

Bioleaching of heavy metals from sewage sludge by Acidithiobacillus thiooxidans. A comparative study

Energy Technology Data Exchange (ETDEWEB)

Wen, Ye-Ming; Wang, Qing-Ping; Chen, Zu-Liang [Fujian Normal Univ., Fuzhou (China). School of Environmental Science and Engineering; Tang, Caixian [La Trobe Univ., Melbourne, VIC (Australia). Dept. of Agricultural Sciences

2012-06-15

To understand the bioleaching of metals from sludge by Acidithiobacillus thiooxidans, the aims of this study were to evaluate the experimental conditions affecting the efficiency of removal of the metals, including solids concentration, initial pH, sulfur concentration and inoculum level were examined, and following the bioleaching mechanism was proposed. Materials and methods: A. thiooxidans were isolated from collected sludge samples containing bacteria from Fuzhou Jingshan sewage treatment plant, and identification of bacteria by sequencing the 16 s rDNA gene sequences. Conditions affecting the bioleaching and application were conducted by batch experiments. The analysis of Cr, Cu, Pb, and Zn was carried out using an atomic absorption spectrophotometer, and the pH and oxidation-reduction potential (ORP) were measured using a pH meter and an ORP meter. The results show that a high metal leaching efficiency was achieved at low solid concentrations due to decreases in buffering capacity. In addition, the best conditions of the bioleaching included 2 % (w/{nu}) solid concentration, 5.0 gL{sup -1} sulfur concentration, and 10 % ({nu}/{nu}) inoculum concentration, where the removal efficiencies of Cr, Cu, Pb, and Zn in sewage sludge was 43.6 %, 96.2 %, 41.6 %, and 96.5 %, respectively. We found that the bioleaching of Zn was governed by direct and indirect mechanisms, while the bioleaching of Cu, Pb, and Cr was mainly dominated by the bioleaching indirect mechanism. After processing with the proposed techniques, the heavy metals in the sewage sludge did meet the requirement of the national standards. (orig.)

Sludge Digestion Manual; Handboek Slibgisting

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-09-15

This manual offers a guideline for developing, designing, optimizing and operating sludge digestion installations based on sewage sludge. It also offers tools for solving operation problems [Dutch] Het Handboek is een leidraad voor het ontwikkelen, ontwerpen, optimaliseren en bedrijven van slibgistingsinstallaties voor zuiveringsslib. Ook geeft het handvatten voor het oplossen van operationele problemen.

Effects of ultrasonic disintegration of excess sewage sludge.

Science.gov (United States)

Zielewicz, Ewa

2016-10-01

Breaking down sludge floc (sonodyspergation effect) and destruction of the cell membranes of microorganisms forming floc is a direct effect of ultrasonic disintegration of sludge excess. This results in release of organic material by liquid sludge (the sonolysis effect). Desired technological effects of the disintegration are: to shorten the hydrolytic phase of fermentation, to increase the production of biogas (source of renewable energy) and an increased mineralization (stability) of fermented sludge. The presented study demonstrates research covering thickened excess sludge of various physicochemical properties, collected from nine municipal sewage treatment plants. The sludge was subjected to ultrasonic disintegration using three differently constructed disintegrators and different proportions of sonification area. Direct effects of disintegration were monitored and recorded using selected indicators describing changes in the properties of sludge and increase of substance dispersed and dissolved in the supernatant liquid to be filtered. Studies have demonstrated that those (direct) effects of ultrasonic disintegration depend on the physicochemical properties of the sludge (foremost the concentration of dry solids) that determine their variable susceptibility to the disintegration methods. The direct effects also depend on optimal process conditions (which consist of the construction of the ultrasonic disintegrator), the geometric proportions of the sonication area and the operating parameters of disintegration (which could be appropriately matched to the characteristics of sludge). The most preferable results were obtained for ultrasonic disintegration of sludge with a dry matter concentration C 0 < 4.2 %. The highest effect of sonolysis-an almost 30-fold increase in the COD dissolved in the supernatant-was obtained for the sludge of lowest dry matter (C 0 = 2.0 %), which was sonicated in a reactor with a short transducer of the largest radiating surface

Use of sewage sludge for agriculture in Japan

International Nuclear Information System (INIS)

Kumazawa, K.

1997-01-01

In Japan, the use of sewage sludge and composted sewage sludge is gradually increasing. They are applied not only to agricultural land, but also to golf courses, parks, etc. The presence of heavy metals and pathogens poses a major problem for such utilization of sludge. Composting is a traditional method of sewage treatment. Laws have been introduced and guidelines prepared for proper and safe use of these materials by farmers. Public acceptance plays a crucial role. At a time when environmental preservation is a major issue in almost every aspect of life, greater emphasis will have to be placed on making sludge and compost hygienically acceptable with minimum contamination from pathogenic organisms and heavy metals. The advantages of using sludges as fertilizer for improving and sustaining soil fertility and crop production are many. This paper reviews studies conducted on the use of sewage sludge in agriculture in japan. (author)

105-KW Sandfilter Backwash Pit sludge volume calculation

International Nuclear Information System (INIS)

Dodd, E.N. Jr.

1995-01-01

The volume of sludge contained in the 100-KW Sandfilter Backwash Pit (SFBWP) was calculated from depth measurements of the sludge, pit dimension measurements and analysis of video tape recordings taken by an underwater camera. The term sludge as used in this report is any combination of sand, sediment, or corrosion products visible in the SFBWP area. This work was performed to determine baseline volume for use in determination of quantities of uranium and plutonium deposited in the pit from sandfilter backwashes. The SFBWP has three areas where sludge is deposited: (1) the main pit floor, (2) the transfer channel floor, and (3) the surfaces and structures in the SFBWP. The depths of sludge and the uniformity of deposition varies significantly between these three areas. As a result, each of the areas was evaluated separately. The total volume of sludge determined was 3.75 M 3 (132.2 ft 3 )

Phase chemistry and radionuclide retention from simulated tank sludges

International Nuclear Information System (INIS)

KRUMHANSL, JAMES L.; LIU, J.; ARTHUR, SARA E.; HUTCHERSON, SHEILA K.; QIAN, MORRIS; ANDERSON, HOWARD L.

2000-01-01

Decommissioning high level nuclear waste tanks will leave small amounts of residual sludge clinging to the walls and floor of the structures. The permissible amount of material left in the tanks depends on the radionuclide release characteristics of the sludge. At present, no systematic process exists for assessing how much of the remaining inventory will migrate, and which radioisotopes will remain relatively fixed. Working with actual sludges is both dangerous and prohibitively expensive. Consequently, methods were developed for preparing sludge simulants and doping them with nonradioactive surrogates for several radionuclides and RCRA metals of concern in actual sludges. The phase chemistry of these mixes was found to be a reasonable match for the main phases in actual sludges. Preliminary surrogate release characteristics for these sludges were assessed by lowering the ionic strength and pH of the sludges in the manner that would occur if normal groundwater gained access to a decommissioned tank. Most of the Se, Cs and Tc in the sludges will be released into the first pulse of groundwater passing through the sludge. A significant fraction of the other surrogates will be retained indefinitely by the sludges. This prolonged sequestration results from a combination coprecipitated and sorbed into or onto relatively insoluble phases such as apatite, hydrous oxides of Fe, Al, Bi and rare earth oxides and phosphates. The coprecipitated fraction cannot be released until the host phase dissolves or recrystallizes. The sorbed fraction can be released by ion exchange processes as the pore fluid chemistry changes. However, these releases can be predicted based on a knowledge of the fluid composition and the surface chemistry of the solids. In this regard, the behavior of the hydrous iron oxide component of most sludges will probably play a dominant role for many cationic radionuclides while the hydrous aluminum oxides may be more important in governing anion releases

Gas Generation from K East Basin Sludges - Series II Testing

International Nuclear Information System (INIS)

Bryan, Samuel A.; Delegard, Calvin H.; Schmidt, Andrew J.; Sell, Rachel L.; Silvers, Kurt L.; Gano, Susan R.; Thornton, Brenda M.

2001-01-01

This report describes work to examine the gas generation behavior of actual K East (KE) Basin floor, pit and canister sludge. Mixed and unmixed and fractionated KE canister sludge were tested, along with floor and pit sludges from areas in the KE Basin not previously sampled. The first report in this series focused on gas generation from KE floor and canister sludge collected using a consolidated sampling technique. The third report will present results of gas generation testing of irradiated uranium fuel fragments with and without sludge addition. The path forward for management of the K Basin Sludge is to retrieve, ship, and store the sludge at T Plant until final processing at some future date. Gas generation will impact the designs and costs of systems associated with retrieval, transportation and storage of sludge