WorldWideScience

Sample records for slovenian triga mark

  1. Utilization of Slovenian TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Snoj, L.; Smodis, B.

    2010-01-01

    TRIGA Mark II research reactor at the Jozef Stefan Institute [JSI] is extensively used for various applications, such as: irradiation of various samples, training and education, verification and validation of nuclear data and computer codes, testing and development of experimental equipment used for core physics tests at a nuclear power plant. The paper briefly describes the aforementioned activities and shows that even such small reactors are still indispensable in nuclear science and technology. (author)

  2. Reaction Rate Benchmark Experiments with Miniature Fission Chambers at the Slovenian TRIGA Mark II Reactor

    Science.gov (United States)

    Štancar, Žiga; Kaiba, Tanja; Snoj, Luka; Barbot, Loïc; Destouches, Christophe; Fourmentel, Damien; Villard, Jean-François AD(; )

    2018-01-01

    A series of fission rate profile measurements with miniature fission chambers, developed by the Commisariat á l'énergie atomique et auxénergies alternatives, were performed at the Jožef Stefan Institute's TRIGA research reactor. Two types of fission chambers with different fissionable coating (235U and 238U) were used to perform axial fission rate profile measurements at various radial positions and several control rod configurations. The experimental campaign was supported by an extensive set of computations, based on a validated Monte Carlo computational model of the TRIGA reactor. The computing effort included neutron transport calculations to support the planning and design of the experiments as well as calculations to aid the evaluation of experimental and computational uncertainties and major biases. The evaluation of uncertainties was performed by employing various types of sensitivity analyses such as experimental parameter perturbation and core reaction rate gradient calculations. It has been found that the experimental uncertainty of the measurements is sufficiently low, i.e. the total relative fission rate uncertainty being approximately 5 %, in order for the experiments to serve as benchmark experiments for validation of fission rate profiles. The effect of the neutron flux redistribution due to the control rod movement was studied by performing measurements and calculations of fission rates and fission chamber responses in different axial and radial positions at different control rod configurations. It was confirmed that the control rod movement affects the position of the maximum in the axial fission rate distribution, as well as the height of the local maxima. The optimal detector position, in which the redistributions would have minimum effect on its signal, was determined.

  3. Decontamination of TRIGA Mark II reactor, Indonesia

    International Nuclear Information System (INIS)

    Suseno, H.; Daryoko, M.; Goeritno, A.

    2002-01-01

    The TRIGA Mark II Reactor in the Centre for Research and Development Nuclear Technique Bandung has been partially decommissioned as part of an upgrading project. The upgrading project was carried out from 1995 to 2000 and is being commissioned in 2001. The decommissioning portion of the project included disassembly of some components of the reactor core, producing contaminated material. This contaminated material (grid plate, reflector, thermal column, heat exchanger and pipe) will be sent to the Decontamination Facility at the Radioactive Waste Management Development Centre. (author)

  4. Decommissioning of TRIGA Mark II type reactor

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Dooseong; Jeong, Gyeonghwan; Moon, Jeikwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2012-10-15

    The first research reactor in Korea, KRR 1, is a TRIGA Mark II type with open pool and fixed core. Its power was 100 kWth at its construction and it was upgraded to 250 kWth. Its construction was started in 1957. The first criticality was reached in 1962 and it had been operated for 36,000 hours. The second reactor, KRR 2, is a TRIGA Mark III type with open pool and movable core. These reactors were shut down in 1995, and the decision was made to decommission both reactors. The aim of the decommissioning activities is to decommission the KRR 2 reactor and decontaminate the residual building structures and site, and to release them as unrestricted areas. The KRR 1 reactor was decided to be preserve as a historical monument. A project was launched for the decommissioning of these reactors in 1997, and approved by the regulatory body in 2000. A total budget for the project was 20.0 million US dollars. It was anticipated that this project would be completed and the site turned over to KEPCO by 2010. However, it was discovered that the pool water of the KRR 1 reactor was leaked into the environment in 2009. As a result, preservation of the KRR 1 reactor as a monument had to be reviewed, and it was decided to fully decommission the KRR 1 reactor. Dismantling of the KRR 1 reactor takes place from 2011 to 2014 with a budget of 3.25 million US dollars. The scope of the work includes licensing of the decommissioning plan change, removal of pool internals including the reactor core, removal of the thermal and thermalizing columns, removal of beam port tubes and the aluminum liner in the reactor tank, removal of the radioactive concrete (the entire concrete structure will not be demolished), sorting the radioactive waste (concrete and soil) and conditioning the radioactive waste for final disposal, and final statuses of the survey and free release of the site and building, and turning over the site to KEPCO. In this paper, the current status of the TRIGA Mark-II type reactor

  5. Decommissioning plan for the TRIGA mark-3

    International Nuclear Information System (INIS)

    Park, S. K.; Jung, W. S.; Jung, K. H.; Baek, S. T.; Jung, K. J.

    1999-01-01

    TRIGA Mark-III (KRR-2) is the second research reactor in Korea. Construction of KRR-2 was started in 1969 and first criticality was achieved in 1972. After 24 years operation, KRR-2 has stopped its operation at the end of 1995 due to normal operation of HANARO. KRR-2 was then decided to decommission in 1996 by government. Decontamination and decommissioning (D and D) will be conducted in accordance with domestic laws and international regulations. Selected method of D and D will be devoted to protect workers and environment and to minimize radioactive wastes produced. The major D and D work will be conducted safely by using conventional industrial equipment because of relatively low radioactivity and contamination in the facility. When removing activated concrete from reactor pool, it will be installed a temporary containment and ventilation system. In this paper, structure of KRR-2 and method of D and D in each step are presented and discussed

  6. Neutron Field Characterization of Irradiation Locations Applied to the Slovenian TRIGA Reactor

    International Nuclear Information System (INIS)

    Barbot, Loic; Domergue, Christophe; Breaud, Stephane; Destouches, Christophe; Villard, Jean-Francois; Snoj, Luka; Stancar, Ziga; Radulovic, Vladimir; Trkov, Andrej

    2013-06-01

    This work deals with several neutron flux measurement instruments and particle transport calculations combined in a method to assess the neutron field in experimental locations in nuclear reactor core or reflector. First test of this method in the TRIGA Mark II of Slovenia led to the assessment of three energy groups neutron fluxes in central irradiation locations within reactor core. (authors)

  7. Evaluation of TRIGA Mark II reactor in Turkey

    International Nuclear Information System (INIS)

    Bilge, Ali Nezihi

    1990-01-01

    There are two research reactors in Turkey and one of them is the university Triga Mark II reactor which was in service since 1979 both for education and industrial application purposes. The main aim of this paper is to evaluate the spectrum of the services carried by Turkish Triga Mark II reactor. In this work, statistical distribution of the graduate works and applications, by using Triga Mark II reactor is examined and evaluated. In addition to this, technical and scientific uses of this above mentioned reactor are also investigated. It was already showed that the uses and benefits of this reactor can not be limited. If the sufficient work and service is given, NDT and industrial applications can also be carried economically. (orig.)

  8. TRIGA Mark II Ljubljana - spent fuel transportation

    International Nuclear Information System (INIS)

    Ravnik, M.; Dimic, V.

    2008-01-01

    The most important activity in 1999 was shipment of the spent fuel elements back to the United States for final disposal. This activity started already in 1998 with some governmental support. In July 1999 all spent fuel elements (219 pieces) from the TRIGA research reactor in Ljubljana were shipped back to the United Stated by the ship from the port Koper in Slovenia. At the same time shipment of the spent fuel from the research reactor in Pitesti, Romania, and the research reactor in Rome, Italy, was conducted. During the loading the radiation exposure to the workers was rather low. The loading and shipment of the spent nuclear fuel went very smoothly and according the accepted time table. During the last two years the TRIGA research reactor in Ljubljana has been in operation about 1100 hours per year and without any undesired shut-down. (authors)

  9. Probabilistic Safety Assessment Of It TRIGA Mark-II Reactor

    International Nuclear Information System (INIS)

    Ergun, E; Kadiroglu, O.S.

    1999-01-01

    The probabilistic safety assessment for Istanbul Technical University (ITU) TRIGA Mark-II reactor is performed. Qualitative analysis, which includes fault and event trees and quantitative analysis which includes the collection of data for basic events, determination of minimal cut sets, calculation of quantitative values of top events, sensitivity analysis and importance measures, uncertainty analysis and radiation release from fuel elements are considered

  10. Twenty years of Triga Mark I reactor use

    International Nuclear Information System (INIS)

    Stasiulevicius, R.; Maretti Junior, F.

    1981-01-01

    This work is a report on the 20 years of activities of the Triga Mark I, research reactor located in Belo Horizonte, Brazil. It contains also a list of publications, details of operation and improvements introduced in the reactor as well as some perspectives for its future. (A.C.A.S.)

  11. Thermal spectra of the TRIGA Mark III reactor; El espectro termico del reactor TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Macias B, L.R.; Palacios G, J. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1998-07-01

    The diffraction phenomenon is gave in observance of the well known Bragg law in crystalline materials and this can be performance by mean of X-rays, electrons and neutrons among others, which allows to do inside the field of each one of these techniques the obtaining of measurements focussed at each one of them. For the present work, it will be mentioned only the referring to X-ray and neutron techniques. The X-ray diffraction due to its properties just it does measurements which are known in general as superficial measurements of the sample material but for the properties of the neutrons, this diffraction it explores in volumetric form the sample material. Since the neutron diffraction process depends lots of its intensity, then it is important to know the neutron source spectra that in this case is supplied by the TRIGA Mark III reactor. Within of diffraction techniques a great number of them can be found, however some of the traditional will be mentioned such as the identification of crystalline samples, phases identification and the textures measurement. At present this last technique is founded on the dot of a minimum error and the technique of phases identification performs but not compete with that which is obtained by mean of X-rays due to this last one has a major resolution. (Author)

  12. Data base formation for important components of reactor TRIGA MARK II

    Energy Technology Data Exchange (ETDEWEB)

    Jordan, R; Mavko, B; Kozuh, M [Inst. Jozef Stefan, Ljubljana (Slovenia)

    1992-07-01

    The paper represents specific data base formation for reactor TRIGA MARK II in Podgorica. Reactor operation data from year 1985 to 1990 were collected. Two groups of collected data were formed. The first group includes components data and the second group covers data of reactor scrams. Time related and demand related models were used for data evaluation. Parameters were estimated by classical method. Similar data bases are useful everywhere where components unavailabilities may have severe drawback. (author) [Slovenian] V referatu smo prikazali raziskavo, v okviru katere smo za raziskovalni reaktor TRIGA MARK II v Podgorici izoblikovali specificno bazo podatkov. Zbrali smo podatke obratovanja reaktorja od leta 1985 do 1990. Rezultate raziskave dogodkov smo razdelili v dve glavni skupini. V prvo spadajo obratovalni podatki o komponentah, v drugo skupino pa spadajo zagoni oz. zaustavitve reaktorja. Podatke smo ovrednotili z modelom v casovnem prostoru in z modelom na zahtevo. Parametre modelov smo dolocili s klasicno metodo. Opisane baze podatkov so uporabne povsod, kjer so lahko posledice nezanesljivega delovanja sistemov velike. [author].

  13. Performances on nuclear activation analysis by TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Capannesi, G.; Rosada, A.

    1986-01-01

    Progresses in methodological research and connected applications in the field of activation analysis are introduced. Some peculiar characteristics on the TRIGA MARK II reactor have enabled the possibility of obtaining interesting results. The particular, the rotating radiation device Lazy Susan, with a capability of 40 positionings, permits homogeneity in neutron flux and energy spectrum stability within 15%. High level of precision and accuracy are obtained in analytic. Applications of major interest have been: - reference material certification; - forensic applications; - electrolytic cell productivity evaluation. The TRIGA MARK II reactor is equipped with a thermal column throughout a D 2 O diaphragm with a thickness of 70 cm. The available neutron flux has no fast and epithermal components. Via this facility a method has been tested for the instrumental determination of Al in Si metal of solar and electronic degree. (author)

  14. Preliminary neutronic design of TRIGA Mark II Reactor

    International Nuclear Information System (INIS)

    Sarikaya, B.; Tombakoglu, M.; Cecen, Y.; Kadiroglu, O. K.

    2001-01-01

    It is very important to analyse the behaviour of the research reactors, since, they play a key role in developing the power reactor technology and radiation applications such as isotope generation for medical treatments. In this study, the neutronic behaviour of the TRIGA MARK II reactor, owned and operated by Istanbul Technical University is analysed by using the SCALE code system. In the analysis, in order to overcome the disadvantages of special TRIGA codes, such as TRIGAP, the SCALE code system is chosen to perform the calculations. TRIGAP and similar codes have limited geometrical (one-dimensional geometry) and cross sectional options (two-group calculations), however, SCALE has the capability of wider range of geometrical modelling capability (three-dimensional modelling is possible) and multi-group calculations are possible

  15. Temperature feedback of TRIGA MARK-II fuel

    Science.gov (United States)

    Usang, M. D.; Minhat, M. S.; Rabir, M. H.; M. Rawi M., Z.

    2016-01-01

    We study the amount of temperature feedback on reactivity for the three types of TRIGA fuel i.. ST8, ST12 and LEU fuel, are used in the TRIGA MARK II reactor in Malaysia Nuclear Agency. We employ WIMSD-5B for the calculation of kin f for a single TRIGA fuel surrounded by water. Typical calculations of TRIGA fuel reactivity are usually limited to ST8 fuel, but in this paper our investigation extends to ST12 and LEU fuel. We look at the kin f of our model at various fuel temperatures and calculate the amount reactivity removed. In one instance, the water temperature is kept at room temperature of 300K to simulate sudden reactivity increase from startup. In another instance, we simulate the sudden temperature increase during normal operation where the water temperature is approximately 320K while observing the kin f at various fuel temperatures. For accidents, two cases are simulated. The first case is for water temperature at 370K and the other is without any water. We observe that the higher Uranium content fuel such as the ST12 and LEU have much smaller contribution to the reactivity in comparison to the often studied ST8 fuel. In fact the negative reactivity coefficient for LEU fuel at high temperature in water is only slightly larger to the negative reactivity coefficient for ST8 fuel in void. The performance of ST8 fuel in terms of negative reactivity coefficient is cut almost by half when it is in void. These results are essential in the safety evaluation of the reactor and should be carefully considered when choices of fuel for core reconfiguration are made.

  16. Corrosion problem in the CRENK Triga Mark II research reactor

    International Nuclear Information System (INIS)

    Kalenga, M.

    1990-01-01

    In August 1987, a routine underwater optical inspection of the aluminum tank housing the core of the CRENK Triga Mark II reactor, carried out to update safety condition of the reactor, revealed pitting corrosion attacks on the 8 mm thick aluminum tank bottom. The paper discuss the work carried out by the reactor staff to dismantle the reactor in order to allow a more precise investigation of the corrosion problem, to repair the aluminum tank bottom, and to enhance the reactor overall safety condition

  17. Burn-up TRIGA Mark II benchmark experiment

    International Nuclear Information System (INIS)

    Persic, A.; Ravnik, M.; Zagar, T.

    1998-01-01

    Different reactor codes are used for calculations of reactor parameters. The accuracy of the programs is tested through comparison of the calculated values with the experimental results. Well-defined and accurately measured benchmarks are required. The experimental results of reactivity measurements, fuel element reactivity worth distribution and fuel-up measurements are presented in this paper. The experiments were performed with partly burnt reactor core. The experimental conditions were well defined, so that the results can be used as a burn-up benchmark test case for a TRIGA Mark II reactor calculations.(author)

  18. The optimal control of ITU TRIGA Mark II Reactor

    International Nuclear Information System (INIS)

    Can, Burhanettin

    2008-01-01

    In this study, optimal control of ITU TRIGA Mark-II Reactor is discussed. A new controller has been designed for ITU TRIGA Mark-II Reactor. The controller consists of main and auxiliary controllers. The form is based on Pontragyn's Maximum Principle and the latter is based on PID approach. For the desired power program, a cubic function is chosen. Integral Performance Index includes the mean square of error function and the effect of selected period on the power variation. YAVCAN2 Neutronic - Thermal -Hydraulic code is used to solve the equations, namely 11 equations, dealing with neutronic - thermal - hydraulic behavior of the reactor. For the controller design, a new code, KONTCAN, is written. In the application of the code, it is seen that the controller controls the reactor power to follow the desired power program. The overshoot value alters between 100 W and 500 W depending on the selected period. There is no undershoot. The controller rapidly increases reactivity, then decreases, after that increases it until the effect of temperature feedback is compensated. Error function varies between 0-1 kW. (author)

  19. MCNP simulation of the TRIGA Mark II benchmark experiment

    International Nuclear Information System (INIS)

    Jeraj, R.; Glumac, B.; Maucec, M.

    1996-01-01

    The complete 3D MCNP model of the TRIGA Mark II reactor is presented. It enables precise calculations of some quantities of interest in a steady-state mode of operation. Calculational results are compared to the experimental results gathered during reactor reconstruction in 1992. Since the operating conditions were well defined at that time, the experimental results can be used as a benchmark. It may be noted that this benchmark is one of very few high enrichment benchmarks available. In our simulations experimental conditions were thoroughly simulated: fuel elements and control rods were precisely modeled as well as entire core configuration and the vicinity of the core. ENDF/B-VI and ENDF/B-V libraries were used. Partial results of benchmark calculations are presented. Excellent agreement of core criticality, excess reactivity and control rod worths can be observed. (author)

  20. Ageing Management in the CENM Triga Mark II Research Reactor

    Energy Technology Data Exchange (ETDEWEB)

    El Younoussi, C.; Nacir, B.; El Bakkari, B.; Boulaich, Y. [Centre for Nuclear Studies of Maâmora (CENM), National Centre of Energy Sciences and Nuclear Techniques (CNESTEN), Rabat (Morocco)

    2014-08-15

    Physical ageing is one of the most important factors that may reduce the safety margins calculated in the design of safety system components of a research reactor. In this context, special efforts are necessary for ensuring the safety of research reactors through appropriate ageing management actions. The paper deals with the overall aspects of the ageing management system of the Moroccan TRIGA Mark II research reactor. The management system covers among others, management of structures, critical components inspections, the control command system and nuclear instrumentation verification. The paper presents also how maintenance and periodic testing are organized and managed in the reactor module. Practical examples of ageing management actions of some systems and components during recent years are presented. (author)

  1. Decommissioning of the ICI TRIGA Mark I reactor

    International Nuclear Information System (INIS)

    Parry, D.R.; England, M.R.; Ward, A.; Green, D.

    2000-01-01

    This paper considers the fuel removal, transportation and subsequent decommissioning of the ICI TRIGA Mark I Reactor at Billingham, UK. BNFL Waste Management and Decommissioning carried out this work on behalf of ICI. The decommissioning methodology was considered in the four stages to be described, namely Preparatory Works, Reactor Defueling, Intermediate Level Waste Removal and Low Level Waste Removal. This paper describes the principal methodologies involved in the defueling of the reactor and subsequent decommissioning operations, highlighting in particular the design and safety case methodologies used in order to achieve a solution which was completed without incident or accident and resulted in a cumulative radiation dose to personnel of only 1.57 mSv. (author)

  2. Planned Scientific programs around the Triga Mark 2 Reactor

    International Nuclear Information System (INIS)

    Majah, M Ibn.

    2007-01-01

    Full text: Nuclear techniques have been introduced to Morocco since the sixties. After the energy crisis of 1973, Morocco decides to create the National Center for Energy Sciences and Nuclear Techniques (CNESTEN) under the supervision of the Ministry of high Education and Research, with a research commercial and support vocation. CNESTEN is in charge of promoting nuclear application, to act as technical support for the authorities and to prepare the technological basis for nuclear power option. In 1998, CNESTEN started the construction of Nuclear Research Centre. The on going activities cover many sectors : earth and environmental sciences, high energy physics, safety and security, waste management. In 2001, CNESTEN started the construction of a 2MW TRiga Mark 2 Reactor, with the possibility to increase the power to 3 MW. The construction was achieved in January 2007. The operation of the reactor is expected for April 2007. The program of the utilization of the reactor was established with th contribution of the university and with the assistance of IAEA. Some of the experimental set-up installed around the reactor have been designed. CNESTEN has developed cooperation with Nuclear research centres from other countries and is receiving visitors and trainees mainly through the IAEA [fr

  3. Neutronics analysis of TRIGA Mark II research reactor

    Directory of Open Access Journals (Sweden)

    Haseebur Rehman

    2018-02-01

    Full Text Available This article presents clean core criticality calculations and control rod worth calculations for TRIGA (Training, Research, Isotope production-General Atomics Mark II research reactor benchmark cores using Winfrith Improved Multi-group Scheme-D/4 (WIMS-D/4 and Program for Reactor In-core Analysis using Diffusion Equation (PRIDE codes. Cores 133 and 134 were analyzed in 2-D (r, θ and 3-D (r, θ, z, using WIMS-D/4 and PRIDE codes. Moreover, the influence of cross-section data was also studied using various libraries based on Evaluated Nuclear Data File (ENDF/B-VI.8 and VII.0, Joint Evaluated Fission and Fusion File (JEFF-3.1, Japanese Evaluated Nuclear Data Library (JENDL-3.2, and Joint Evaluated File (JEF-2.2 nuclear data. The simulation results showed that the multiplication factor calculated for all these data libraries is within 1% of the experimental results. The reactivity worth of the control rods of core 134 was also calculated with different homogenization approaches. A comparison was made with experimental and reported Monte Carlo results, and it was found that, using proper homogenization of absorber regions and surrounding fuel regions, the results obtained with PRIDE code are significantly improved.

  4. Thermal spectra of the TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Macias B, L.R.; Palacios G, J.

    1998-01-01

    The diffraction phenomenon is gave in observance of the well known Bragg law in crystalline materials and this can be performance by mean of X-rays, electrons and neutrons among others, which allows to do inside the field of each one of these techniques the obtaining of measurements focussed at each one of them. For the present work, it will be mentioned only the referring to X-ray and neutron techniques. The X-ray diffraction due to its properties just it does measurements which are known in general as superficial measurements of the sample material but for the properties of the neutrons, this diffraction it explores in volumetric form the sample material. Since the neutron diffraction process depends lots of its intensity, then it is important to know the neutron source spectra that in this case is supplied by the TRIGA Mark III reactor. Within of diffraction techniques a great number of them can be found, however some of the traditional will be mentioned such as the identification of crystalline samples, phases identification and the textures measurement. At present this last technique is founded on the dot of a minimum error and the technique of phases identification performs but not compete with that which is obtained by mean of X-rays due to this last one has a major resolution. (Author)

  5. Perturbation analysis of the TRIGA Mark II reactor Vienna

    Energy Technology Data Exchange (ETDEWEB)

    Khan, R. [Pakistan Institute of Engineering and Applied Sciences (PIEAS), Islamabad (Pakistan); Villa, M.; Stummer, T.; Boeck, H. [Vienna Univ. of Technology (Austria). Atominstitut; Saeedbadshah [International Islamic Univ., Islamabad (Pakistan)

    2013-04-15

    The safety design of a nuclear reactor needs to maintain the steady state operation at desired power level. The safe and reliable reactor operation demands the complete knowledge of the core multiplication and its changes during the reactor operation. Therefore it is frequently of interest to compute the changes in core multiplication caused by small disturbances in the field of reactor physics. These disturbances can be created either by geometry or composition changes of the core. Fortunately if these changes (or perturbations) are very small, one does not have to repeat the reactivity calculations. This article focuses the study of small perturbations created in the Central Irradiation Channel (CIC) of the TRIGA mark II core to investigate their reactivity influences on the core reactivity. For this purpose, 3 different kinds of perturbations are created by inserting 3 different samples in the CIC. The cylindrical void (air), heavy water (D2O) and Cadmium (Cd) samples are inserted into the CIC separately to determine their neutronics behavior along the length of the core. The Monte Carlo N-Particle radiation transport code (MCNP) is applied to simulate these perturbations in the CIC. The MCNP theoretical predictions are verified by the experiments performed on the current reactor core. The behavior of void in the whole core and its dependence on position and water fraction is also presented in this article. (orig.)

  6. Different microprocessor controlled devices for ITU TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Can, B.; Omuz, S.; Uzun, S.; Apan, H.

    1990-01-01

    In this paper the design of a period meter and multichannel thermometer, which are controlled by a microprocessor, in order to be used at ITU TRIGA Mark-II Reactor is presented. The system works as a simple microcomputer, which includes a CPU, a EPROM, a RAM, a CTC, a PIO, a PIA a keyboard and displays, using the assembly language. The period meter can work either with pulse signal or with analog signal depending on demand of the user. The period is calculated by software and its range is -99,9 sec, to +2.1 sec. When the period drops +3 sec, the system gives alarm illuminating a LED. The multichannel thermometer has eight temperature channels. Temperature channels can manually or automatically be selected. The channel selection time can be adjusted. The thermometer gives alarm illuminating a LED, when the temperature rises to 600 C. Temperature data is stored in the RAM and is shown on a display. This system provides us to use four spare thermocouples in the reactor. (orig.)

  7. Twenty years of operation of Ljubljana's TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Dimic, V.

    1986-01-01

    Twenty years have now passed since the start of the TRIGA Mark II reactor in Ljubljana. The reactor was critical on May 31, 1966. The total energy produced until the end of May 1986 was 14.048 MWh or 585 MWd. For the first 14 years (until 1981) the yearly energy produced was about 600 MWh, since 1981 the yearly energy produced was 1000 MWh when a routine radioactive isotopes production started for medical use as well as other industrial applications, such as doping and irradiation with fast neutrons of silicon monocrystals, production of level indicators (irradiated cobalt wire), production of radioactive iridium for gamma-radiography, leak detection in pipes by sodium, etc. Besides these, applied research around the reactor is being conducted in the following main fields, where- many unique methods have been developed or have found their way into the local industry or hospitals: neutron radiography, neutron induced auto-radiography using solid state nuclear track detectors, nondestructive methods for assessment of nuclear burn-up, neutron dosimetry, calculation of core burn-up for the optimal in-core fuel management strategy. The solvent extraction method was developed for the everyday production of 99m Tc, which is the most widely used radionuclide in diagnostic nuclear medicine. The methods were developed for the production of the following isotopes: 18 F, 85m Kr, 24 Na, 82 Br, 64 Zn, 125 I. Neutron activation analysis represents one of the major usages for the TRIGA reactor. Basic research is being conducted in the following main fields: solid state physics (elastic and inelastic scattering of the neutrons), neutron dosimetry, neutron radiography, reactor physics and neutron activation analysis. The reactor is used very extensively as a main instrument in the Reactor Training Centre in Ljubljana where manpower training for our nuclear power plant and other organisations has been performed. Although the reactor was designed very carefully in order to be used for

  8. Flux measurement in ZBR at the TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Dauke, M.

    2005-01-01

    The determination of the neutron flux in the TRIGA-2-Vienna reactor was the objective of this research. The theory of the method (4π-β detectors) is presented as well as the determination of the maximum flux, gold-cadmium differential measurement, cobalt-wire measurement, finally a comparison of all results was made and interpreted. (nevyjel)

  9. Seed irradiation facilities at TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Najzer, M.

    1972-01-01

    Fast neutrons and gamma-rays with their high and low LET respectively are excellent complementary tools for investigation of the effect of different types of mutations. TRIGA Irradiation Facility and Thermal Column Irradiation Facility were designed and installed for the first time in the TRIGA tank and thermal column respectively. The basic idea of design was the use of depleted uranium as gamma-ray and thermal neutron shield and simultaneously as thermal to fast neutron converter. Low LET radiation, due to direct and thermal neutron capture gamma-rays, is strongly attenuated while fast neutron flux is increased. GIF is made of a cadmium tube inserted in a graphite block. It is located in the central thermal column channel. The basic idea is to convert thermal neutrons to gamma-rays by capture in the cadmium

  10. Neutron beam utilization at the TRIGA Mark II reactor Vienna

    International Nuclear Information System (INIS)

    Villa, M.; Boeck, H.; Ismail, S.; Koerner, S.; Baron, M.; Hainbuchner, M.; Badurek, G.; Buchelt, R.J.

    1999-01-01

    A review is given about the research activities around the 250 kw TRIGA reactor Vienna, which are adequate to other neutron sources of comparable or bigger size. The topics selected for presentation range from neutron radiography, materials irradiation, neutron small-angle scattering, neutron activation analysis, neutron polarization to neutron interferometry. It is the aim of this presentation to stimulate programs for more efficient use around TRIGA research reactors with neutron flux densities of 1013 cm-2a-1 at the center of the reactor core. We briefly describe the experimental facilities installed at the 250 kw TRIGA reactor of the Austrian Universities in Vienna and present a great part of the current research activities performed with them. We believe that most of the techniques and experiments presented here are adequate for implementation to other reactors of similar or even higher power. Those technologies which require extremely specialized know-how not generally available at every research Inst.e will not be treated here or are just mentioned without any further details.(author)

  11. Radiological control guide for decommissioning of the TRIGA mark-2, 3

    International Nuclear Information System (INIS)

    Lee, Bong Jae

    2000-08-01

    The purpose of radiological control for TRIGA mark-2, 3 research reactors and facilities at the KAERI Seoul site, which are to be decommissioned, is in minimizing the radiation exposure for workers and in preventing the release of the radioactive materials to the environment. In order to accomplish these goal, the radiological control guide will be prepared during the decommissioning activities. Therefore, it is expected that this technical report can be used in preparing radiological control guide for safety decommissioning of the TRIGA mark-2, 3

  12. Monte Carlo analysis of Musashi TRIGA mark II reactor core

    International Nuclear Information System (INIS)

    Matsumoto, Tetsuo

    1999-01-01

    The analysis of the TRIGA-II core at the Musashi Institute of Technology Research Reactor (Musashi reactor, 100 kW) was performed by the three-dimensional continuous-energy Monte Carlo code (MCNP4A). Effective multiplication factors (k eff ) for the several fuel-loading patterns including the initial core criticality experiment, the fuel element and control rod reactivity worth as well as the neutron flux measurements were used in the validation process of the physical model and neutron cross section data from the ENDF/B-V evaluation. The calculated k eff overestimated the experimental data by about 1.0%Δk/k for both the initial core and the several fuel-loading arrangements. The calculated reactivity worths of control rod and fuel element agree well the measured ones within the uncertainties. The comparison of neutron flux distribution was consistent with the experimental ones which were measured by activation methods at the sample irradiation tubes. All in all, the agreement between the MCNP predictions and the experimentally determined values is good, which indicated that the Monte Carlo model is enough to simulate the Musashi TRIGA-II reactor core. (author)

  13. Measuring temperature coefficient of TRIGA MARK I reactor by noise analysis

    International Nuclear Information System (INIS)

    Soares, P.A.

    1975-01-01

    The transfer function of TRIGA MARK I Reactor is measured at power zero (5w) and power 118Kw, in the frequency range of 0.02 to 0.5 rd/s. The method of intercorrelation between a pseudostochasticbinary signal is used. A simple dynamic model of the reactor is developed and the coefficient of temperature is estimated [pt

  14. Modernization design of neutron radiography of ITU TRIGA Mark-II reactor

    International Nuclear Information System (INIS)

    Tugrul, B.; Bilge, A.N.

    1988-01-01

    ITU TRIGA MARK-II Research and Training Reactor has a power of 250 KW and has three beam tubes. One of them is tangential beam tube used for neutron radiography. In this study, the neutron radiography set in the tangential beam tube is described with its problems for ITU TRIGA Reactor. After that modernization of the system is designed and the applicability of the direct and indirect methods is evaluated. Improving the ratio of length to diameter for the beam tube, elimination the fogging on the film and constructive design for practice and secure application of the technique is developed. (author)

  15. Characterization of the TRIGA Mark II reactor full-power steady state

    Energy Technology Data Exchange (ETDEWEB)

    Cammi, Antonio, E-mail: antonio.cammi@polimi.it [Politecnico di Milano – Department of Energy, CeSNEF (Enrico Fermi Center for Nuclear Studies), via La Masa 34, 20156 Milano (Italy); Zanetti, Matteo [Politecnico di Milano – Department of Energy, CeSNEF (Enrico Fermi Center for Nuclear Studies), via La Masa 34, 20156 Milano (Italy); Chiesa, Davide; Clemenza, Massimiliano; Pozzi, Stefano; Previtali, Ezio; Sisti, Monica [University of Milano-Bicocca, Physics Department “G. Occhialini” and INFN Section, Piazza dell’Ateneo Nuovo, 20126 Milan (Italy); Magrotti, Giovanni; Prata, Michele; Salvini, Andrea [University of Pavia, Applied Nuclear Energy Laboratory (L.E.N.A.), Via Gaspare Aselli 41, 27100 Pavia (Italy)

    2016-04-15

    Highlights: • Full-power steady state characterization of the TRIGA Mark II reactor. • Monte Carlo and Multiphysics simulation of the TRIGA Mark II reactor. • Sub-cooled boiling effects in the TRIGA Mark II reactor. • Thermal feedback effects in the TRIGA Mark II reactor. • Experimental data based validation. - Abstract: In this paper, the characterization of the full-power steady state of the TRIGA Mark II nuclear reactor at the University of Pavia is achieved by coupling the Monte Carlo (MC) simulation for neutronics with the “Multiphysics” model for thermal-hydraulics. Neutronic analyses have been carried out with a MCNP5 based MC model of the entire reactor system, already validated in fresh fuel and zero-power configurations (in which thermal effects are negligible) and using all available experimental data as a benchmark. In order to describe the full-power reactor configuration, the temperature distribution in the core must be established. To evaluate this, a thermal-hydraulic model has been developed, using the power distribution results from the MC simulation as input. The thermal-hydraulic model is focused on the core active region and takes into account sub-cooled boiling effects present at full reactor power. The obtained temperature distribution is then entered into the MC model and a benchmark analysis is carried out to validate the model in fresh fuel and full-power configurations. An acceptable correspondence between experimental data and simulation results concerning full-power reactor criticality proves the reliability of the adopted methodology of analysis, both from the perspective of neutronics and thermal-hydraulics.

  16. Activation of TRIGA Mark II research reactor concrete shield

    International Nuclear Information System (INIS)

    Zagar, Tomaz; Ravnik, Matjaz; Bozic, Matjaz

    2002-01-01

    To determine neutron activation inside the TRIGA research reactor concrete body a special sample-holder for irradiation inside horizontal channel was developed and tested. In the sample-holder various samples can be irradiated at different concrete shielding depths. In this paper the description of the sample-holder, experiment conditions and results of long-lived activation measurements are given. Long-lived neutron-induced gamma-ray-emitting radioactive nuclides in the samples were measured with HPGe detector. The most active long-lived radioactive nuclides in ordinary concrete samples were found to be 60 Co and 152 Eu and in barytes concrete samples 60 Co, 152 Eu and 133 Ba. Measured activity density of all nuclides was found to decrease almost linearly with depth in logarithmic scale. (author)

  17. Computer code for the thermal-hydraulic analysis of ITU TRIGA Mark-II reactor

    International Nuclear Information System (INIS)

    Ustun, G.; Durmayaz, A.

    2002-01-01

    Istanbul Technical University (ITU) TRIGA Mark-II reactor core consists of ninety vertical cylindrical elements located in five rings. Sixty-nine of them are fuel elements. The reactor is operated and cooled with natural convection by pool water, which is also cooled and purified in external coolant circuits by forced convection. This characteristic leads to consider both the natural and forced convection heat transfer in a 'porous-medium analysis'. The safety analysis of the reactor requires a thermal-hydraulic model of the reactor to determine the thermal-hydraulic parameters in each mode of operation. In this study, a computer code cooled TRIGA-PM (TRIGA - Porous Medium) for the thermal-hydraulic analysis of ITU is considered. TRIGA Mark-II reactor code has been developed to obtain velocity, pressure and temperature distributions in the reactor pool as a function of core design parameters and pool configuration. The code is a transient, thermal-hydraulic code and requires geometric and physical modelling parameters. In the model, although the reactor is considered as only porous medium, the other part of the reactor pool is considered partly as continuum and partly as porous medium. COMMIX-1C code is used for the benchmark purpose of TRIGA-PM code. For the normal operating conditions of the reactor, estimations of TRIGA-PM are in good agreement with those of COMMIX-1C. After some more improvements, this code will be employed for the estimation of LOCA scenario, which can not be analyses by COMMIX-1C and the other multi-purpose codes, considering a break at one of the beam tubes of the reactor

  18. Control console conceptual design for sheet type fuels of Triga Mark-II reactor

    International Nuclear Information System (INIS)

    Eko Priyono; Kurnia Wibowo; Anang Susanto

    2016-01-01

    The control console conceptual design for sheet type fuel of TRIGA Mark-II reactor has been made. The control console conceptual design was made with refer study result of instrument and control system which is used in BATAN'S reactor i.e TRIGA-2000 Bandung, TRIGA Yogyakarta and MPR-30 Serpong. The control console conceptual design was made by using AutoCad software. The control console conceptual design reactor for sheet type fuel of TRIGA Mark-II reactor consist of 5 segments that is 3 segments for placing the computer monitors, 1 segment for placing bargraph displays and recorders and 1 segment for placing panel meters. There are the door on front and back position at each segment for enter and out devices in the console. The control console conceptual design is also equipped by the table along in front of console for placing reactor panel control and for writing, 3 drawers for 3 keyboards. The dimension of console will refer control room size and the components will be placed on console which will be detailed in detail design if this conceptual design has been approved. (author)

  19. Using TRIGA Mark II research reactor for irradiation with thermal neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Kolšek, Aljaž, E-mail: aljaz.kolsek@gmail.com; Radulović, Vladimir, E-mail: vladimir.radulovic@ijs.si; Trkov, Andrej, E-mail: andrej.trkov@ijs.si; Snoj, Luka, E-mail: luka.snoj@ijs.si

    2015-03-15

    Highlights: • Monte Carlo N-Particle Transport Code was used to design and perform calculations. • Characterization of the TRIGA Mark II ex-core irradiation facilities was performed. • The irradiation device was designed in the TRIGA irradiation channel. • The use of the device improves the fraction of thermal neutron flux by 390%. - Abstract: Recently a series of test irradiations was performed at the JSI TRIGA Mark II reactor for the Fission Track-Thermoionization Mass Spectrometry (FT-TIMS) method, which requires a well thermalized neutron spectrum for sample irradiation. For this purpose the Monte Carlo N-Particle Transport Code (MCNP5) was used to computationally support the design of an irradiation device inside the TRIGA model and to support the actual measurements by calculating the neutron fluxes inside the major ex-core irradiation facilities. The irradiation device, filled with heavy water, was designed and optimized inside the Thermal Column and the additional moderation was placed inside the Elevated Piercing Port. The use of the device improves the ratio of thermal neutron flux to the sum of epithermal and fast neutron flux inside the Thermal Column Port by 390% and achieves the desired thermal neutron fluence of 10{sup 15} neutrons/cm{sup 2} in irradiation time of 20 h.

  20. Immobilization of ion exchange radioactive resins of the TRIGA Mark III nuclear reactor; Inmovilizacion de resinas de intercambio ionico radiactivas del reactor nuclear Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Garcia M, H.; Emeterio H, M.; Canizal S, C. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, C.P. 11801 Mexico D.F. (Mexico)

    2000-07-01

    This work has the objective to develop the process and to define the agglutinating material which allows the immobilization of the ion exchange radioactive resins coming from the TRIGA Mark III nuclear reactor contaminated with Ba-133, Co-60, Cs-137, Eu-152, and Mn-54 through the behavior analysis of different immobilization agents such as: bitumens, cement and polyester resin. According to the International Standardization the archetype samples were observed with the following tests: determination of free liquid, leaching, charge resistance, biodegradation, irradiation, thermal cycle, burned resistance. Generally all the tests were satisfactorily achieved, for each agent. Therefore, the polyester resin could be considered as the main immobilizing. (Author)

  1. Decontamination and decommissioning project status of the TRIGA mark-2±3 research reactors

    International Nuclear Information System (INIS)

    Jung, K. J.; Baek, S. T.; Jung, W. S.; Park, S. K.; Jung, K. H.

    1999-01-01

    TRIGA Mark-II, the first research reactor in Korea, has operated since 1962, and the second one, TRIGA Mark-III since 1972. Both of them had their operation phased out in 1995 due to their lives and operation of the new research reactor, HANARO at the Korea Atomic Energy Research Institute (KAERI) in Taejeon. Decontamination and decommissioning (D and D) project of the TRIGA Mark-II and Mark-III was started in January 1997 and will be completed in December 2002. In the first year of the project, work was performed in preparation of the decommissioning plan, start of the environmental impact assessment and setup licensing procedure and documentation for the project with cooperation of Korea Institute of Nuclear Safety (KINS). In 1998, Hyundai Engineering Company (HEC) is the main contractor to do design and licensing documentation for the D and D of both reactors. British Nuclear Fuels plc (BNFL) is technical assisting partner of HEC. The decommissioning plan document was submitted to the Ministry of Science and Technology (MOST) for the decommissioning license in December 1998, and it expecting to be issued a license at the end of September 1999. The goal of this project is to release the reactor site and buildings as an unrestricted area. This paper summarizes current status and future plan for the D and D project

  2. Decontamination and decommissioning project status of the TRIGA Mark II and III in Korea

    International Nuclear Information System (INIS)

    Paik, S.T.; Park, S.K.; Chung, K.W.; Chung, U.S.; Jung, K.J.

    1999-01-01

    TRIGA Mark-II, the first research reactor in Korea, has operated since 1962, and the second one, TRIGA Mark-III since 1972. Both of them had their operation phased out in 1995 due to their lives and operation of the new research reactor, HANARO (High-flux Advanced Neutron Application Reactor) at the Korea Atomic Energy Institute (KAERI) in Taejon. Decontamination and decommissioning (D and D) project of TRIGA Mark-II and Mark-III was started in January 1997 and will be completed in December 2002. The first year of the project, work was performed in preparation of the decommissioning plan, start of the environmental impact assessment and setup licensing procedure and documentation for the project with cooperation of Korea Institute of Nuclear Safety (KINS). Hyundai Engineering Company (HEC) is the main contractor to do design and licensing documentation for the D and D of both reactors. British Nuclear Fuels plc (BNFL) is the technical assisting partner of HEC. The decommissioning plan document was submitted to the Ministry of Since and Technology (MOST) for the decommissioning license in December 1998, and it expecting to be issued a license in mid 1999. The goal of this project is to release the reactor site and buildings as an unrestricted area. This paper summarizes current status and future plan for the D and D project. (author)

  3. Applicable regulations and development of surveillance experiments of criticality approach in the TRIGA III Mark reactor

    International Nuclear Information System (INIS)

    Gonzalez M, J.L.; Aguilar H, F.; Rivero G, T.; Sainz M, E.

    2000-01-01

    In the procedure elaborated to repair the vessel of TRIGA III Mark reactor is required to move toward two tanks of temporal storage the fuel elements which are in operation and the spent fuel elements which are in decay inside the reactor pool. The National Commission of Nuclear Safety and Safeguards (CNSNS) has requested as protection measure that it is carried out a surveillance of the criticality approach of the temporal storages. This work determines the main regulation aspects that entails an experiment of criticality approach, moreover, informing about the results obtained in the developing of this experiments. The regulation aspects are not exclusives for this work in the TRIGA Mark III reactor but they also apply toward any assembling of fissile material. (Author)

  4. The possibility of gamma ray sterilization by using ITU TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Bilge, A.N.; Tugrul, B.; Yavuz, H.

    1988-01-01

    Gamma rays are one of the effective method for sterilization which is preferred for a long time. Generally Co-60 radioisotope sources betatrons or accelerators are used for the sterilization. In this work, it was aimed to find the possibilities of the sterilization by gamma rays obtained in ITU TRIGA Mark-II radial tube. Radiation dosages are measured in the radial tube and several medical products are irradiated. Irradiation is arranged according to the desired dosages. Irradiated sterilized goods (mainly medical products) tested and checked at the Governmental Medical Health Center and results compared with literature. It can be seen that this kind of irradiation is a good tool for sterilization. Unfortunately, because of the stability of the radial tube and impracticality of the system it is rather difficult to compete with industrial system using Co-60 and accelerators. Nevertheless, this type of irradiation is also applicable for the purpose of the sterilization by using ITU TRIGA Mark II. (author)

  5. Fuel Management Strategies for a Possible Future LEU Core of a TRIGA Mark II Vienna

    Energy Technology Data Exchange (ETDEWEB)

    Khan, R.; Villa, M.; Steinhauser, G.; Boeck, H. [Vienna University of Technology-Atominstitut (Austria)

    2011-07-01

    The Vienna University of Technology/Atominstitut (VUT/ATI) operates a TRIGA Mark II research reactor. It is operated with a completely mixed core of three different types of fuel. Due to the US fuel return program, the ATI have to return its High Enriched Uranium (HEU) fuel latest by 2019. As an alternate, the Low Enrich Uranium (LEU) fuel is under consideration. The detailed results of the core conversion study are presented at the RRFM 2011 conference. This paper describes the burn up calculations of the new fuel to predict the future burn up behavior and core life time. It also develops an effective and optimized fuel management strategy for a possible future operation of the TRIGA Mark II with a LEU core. This work is performed by the combination of MCNP5 and diffusion based neutronics code TRIGLAV. (author)

  6. Visual examination program of the TRIGA Mark II reactor Vienna with the nuclear underwater telescope

    International Nuclear Information System (INIS)

    Boeck, H.; Hammer, J.; Varga, K.

    1985-12-01

    The visual inspection programm carried out during a three month shut-period at the TRIGA Mark II reactor Vienna is described. Optical inspection of all welds inside the reactor tank was carried out with an underwater telescope developed by the Central Research Institute of Physics, Budapest, Hungary. It is shown that even after 23 years of reactor operation all tank internals were found to be in good condition and minor defects can be easily repaired by remote handling tools. (Author)

  7. Data base formation for important components of reactor TRIGA MARK II

    International Nuclear Information System (INIS)

    Jordan, R.; Mavko, B.; Kozuh, M.

    1992-01-01

    The paper represents specific data base formation for reactor TRIGA MARK II in Podgorica. Reactor operation data from year 1985 to 1990 were collected. Two groups of collected data were formed. The first group includes components data and the second group covers data of reactor scrams. Time related and demand related models were used for data evaluation. Parameters were estimated by classical method. Similar data bases are useful everywhere where components unavailabilities may have severe drawback. (author) [sl

  8. 3-D flux distribution and criticality calculation of TRIGA Mark-II

    International Nuclear Information System (INIS)

    Can, B.

    1982-01-01

    In this work, the static calculation of the (I.T.U. TRIGA Mark-II) flux distribution has been made. The three dimensional, r-θ-z, representation of the core has been used. In this representation, for different configuration, the flux distribution has been calculated depending on two group theory. The thermal-hydraulics, the poisoning effects have been ignored. The calculations have been made by using the three dimensional and multigroup code CAN. (author)

  9. Over Twenty Years Of Experience In ITU TRIGA MARK-II Reactor

    International Nuclear Information System (INIS)

    Yavuz, Hasbi

    2008-01-01

    I.T.U. TRIGA MARK-II Training and Research Reactor, rated at 250 kW steady-state and 1200 MW pulsing power is the only research and training reactor owned and operated by a university in Turkey. Reactor has been operating since March 11, 1979; therefore the reactor has been operating successfully for more than twenty years. Over the twenty years of operation: - The tangential beam tube was equipped with a neutron radiography facility, which consists of a divergent collimator and exposure room; - A computerized data acquisition system was designed and installed such that all parameters of the reactor, which are observed from the console, could be monitored both in normal and pulse operations; - An electrical power calibration system was built for the thermal power calibration of the reactor; - Publications related with I.T.U. TRIGA MARK-II Training and Research Reactor are listed in Appendix; - Two majors undesired shutdown occurred; - The I.T.U. TRIGA MARK-II Training and Research Reactor is still in operation at the moment. (authors)

  10. Safety analysis calculations for a mixed and full FLIP core in a TRIGA Mark II

    International Nuclear Information System (INIS)

    Ringle, John C.; Hornyik, K.; Robinson, A.H.; Anderson, T.V.; Johnson, A.G.

    1976-01-01

    The Oregon State TRIGA Reactor will be reloading with FLIP fuel in August 1976. As we are the first Mark II TRIGA with a circular grid pattern and graphite reflector to utilize FLIP fuel, the safety analysis calculations performed at other facilities using FLIP were only of limited use to us. A multigroup, multiregion, one-dimensional diffusion theory code was used to calculate power densities in six different operational cores - mixed to full FLIP. Pulsing characteristics were obtained from a computer code based on point kinetics, with adiabatic heating of the fuel, linear temperature dependence of the specific heat, and prompt fuel temperature feedback coefficient. The results of all pertinent calculations will be presented. (author)

  11. Neutronic Analysis of the 3 MW TRIGA MARK II Research Reactor, Part I: Monte Carlo Simulation

    International Nuclear Information System (INIS)

    Huda, M.Q.; Chakrobortty, T.K.; Rahman, M.; Sarker, M.M.; Mahmood, M.S.

    2003-05-01

    This study deals with the neutronic analysis of the current core configuration of a 3 MW TRIGA MARK II research reactor at Atomic Energy Research Establishment (AERE), Savar, Dhaka, Bangladesh and validation of the results by benchmarking with the experimental, operational and available Final Safety Analysis Report (FSAR) values. The three-dimensional continuous-energy Monte Carlo code MCNP4C was used to develop a versatile and accurate full-core model of the TRIGA core. The model represents in detail all components of the core with literally no physical approximation. All fresh fuel and control elements as well as the vicinity of the core were precisely described. Continuous energy cross-section data from ENDF/B-VI and S(α, β) scattering functions from the ENDF/B-V library were used. The validation of the model against benchmark experimental results is presented. The MCNP predictions and the experimentally determined values are found to be in very good agreement, which indicates that the Monte Carlo model is correctly simulating the TRIGA reactor. (author)

  12. Mechanism design for the control rods conduction of TRIGA Mark III reactor in the NINR

    International Nuclear Information System (INIS)

    Franco C, A.

    1997-01-01

    This work presents in the first chapter a general studio about the reactor and the importance of control rods in the reactor , the mechaniucal design attending to requisitions that are imposed for conditions of operation of the reactor are present in the second chapter, the narrow relation that exists with the new control console and the mechanism is developed in the thired chapter, this relation from a point of view of an assembly of components is presents in fourth chapter, finally reaches and perspectives of mechanism forming part of project of the automation of reactor TRIGA MARK III, are present in the fifth chapter. (Author)

  13. Collimator and shielding design for boron neutron capture therapy (BNCT) facility at TRIGA MARK II reactor

    International Nuclear Information System (INIS)

    Mohd Rafi Mohd Solleh; Abdul Aziz Tajuddin; Abdul Aziz Mohamed; Eid Mahmoud Eid Abdel Munem; Mohamad Hairie Rabir; Julia Abdul Karim; Yoshiaki, Kiyanagi

    2011-01-01

    The geometry of reactor core, thermal column, collimator and shielding system for BNCT application of TRIGA MARK II Reactor were simulated with MCNP5 code. Neutron particle lethargy and dose were calculated with MCNPX code. Neutron flux in a sample located at the end of collimator after normalized to measured value (Eid Mahmoud Eid Abdel Munem, 2007) at 1 MW power was 1.06 x 10 8 n/ cm 2 / s. According to IAEA (2001) flux of 1.00 x 10 9 n/ cm 2 / s requires three hours of treatment. Few modifications were needed to get higher flux. (Author)

  14. Neuro-diffuse algorithm for neutronic power identification of TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Rojas R, E.; Benitez R, J. S.; Segovia de los Rios, J. A.; Rivero G, T.

    2009-10-01

    In this work are presented the results of design and implementation of an algorithm based on diffuse logic systems and neural networks like method of neutronic power identification of TRIGA Mark III reactor. This algorithm uses the punctual kinetics equation as data generator of training, a cost function and a learning stage based on the descending gradient algorithm allow to optimize the parameters of membership functions of a diffuse system. Also, a series of criteria like part of the initial conditions of training algorithm are established. These criteria according to the carried out simulations show a quick convergence of neutronic power estimated from the first iterations. (Author)

  15. Biological Tests for Boron Neutron Capture Therapy Research at the TRIGA Mark II Reactor in Pavia

    Energy Technology Data Exchange (ETDEWEB)

    Protti, N.; Ballarini, F.; Bortolussi, S.; De Bari, A.; Stella, S.; Altieri, S. [Department of Nuclear and Theoretical Physics, University of Pavia, Pavia (Italy); Nuclear Physics National Institute (INFN), Pavia (Italy); Bruschi, P. [Department of Nuclear and Theoretical Physics, University of Pavia, Pavia (Italy); Bakeine, J.G.; Cansolino, L.; Clerici, A.M. [Laboratory of Experimental Surgery, Department of Surgery, University of Pavia, Pavia (Italy)

    2011-07-01

    The thermal column of the TRIGA Mark II reactor of the Pavia University is used as an irradiation facility to perform biological tests and irradiations of living systems for Boron Neutron Capture Therapy (BNCT) research. The suitability of the facility has been ensured by studying the neutron flux and the photon background in the irradiation chamber inside the thermal column. This characterization has been realized both by flux and dose measurements as well as by Monte Carlo simulations. The routine irradiations concern in vitro cells cultures and different tumor animal models to test the efficacy of the BNCT treatment. Some results about these experiments will be described. (author)

  16. Analysis of JSI TRIGA MARK II reactor physical parameters calculated with TRIPOLI and MCNP.

    Science.gov (United States)

    Henry, R; Tiselj, I; Snoj, L

    2015-03-01

    New computational model of the JSI TRIGA Mark II research reactor was built for TRIPOLI computer code and compared with existing MCNP code model. The same modelling assumptions were used in order to check the differences of the mathematical models of both Monte Carlo codes. Differences between the TRIPOLI and MCNP predictions of keff were up to 100pcm. Further validation was performed with analyses of the normalized reaction rates and computations of kinetic parameters for various core configurations. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Immobilization of ion exchange radioactive resins of the TRIGA Mark III nuclear reactor

    International Nuclear Information System (INIS)

    Garcia M, H.; Emeterio H, M.; Canizal S, C.

    1999-01-01

    This work has the objective to develop the process and to define the agglutinating material which allows the immobilization of the ion exchange radioactive resins coming from the TRIGA Mark III nuclear reactor contaminated with Ba-133, Co-60, Cs-137, Eu-152, and Mn-54 through the behavior analysis of different immobilization agents such as: bitumens, cement and polyester resin. According to the International Standardization the archetype samples were observed with the following tests: determination of free liquid, leaching, charge resistance, biodegradation, irradiation, thermal cycle, burned resistance. Generally all the tests were satisfactorily achieved, for each agent. Therefore, the polyester resin could be considered as the main immobilizing. (Author)

  18. Characterization of the TRIGA Mark III reactor for k0-neutron activation analysis

    International Nuclear Information System (INIS)

    Diaz R, O.; Herrera P, E.; Lopez R, M.C.

    1997-01-01

    The non-ideality of the epithermal neutron flux distribution in a a reactor site parameter (α), the thermal-to-epithermal neutron ratio (f), the irradiation channel neutron temperature (T n ) and the k 0 -factors for more than 20 isotopes were determined in the 3 typical irradiation positions of the TRIGA Mark III reactor of the National Nuclear Research Institute, Salazar, Mexico, using different experimental methods with conventional and non-conventional monitors. This characterization is used in the k 0 -method of NAA, recently introduced at the Institute. (author). 21 refs., 3 figs., 5 tabs

  19. Neutron flux determination at the IPR-R1 Triga Mark I neutron beam extractor

    International Nuclear Information System (INIS)

    Zangirolami, Dante Marco; Maretti Junior, Fausto; Ferreira, Andrea Vidal

    2009-01-01

    The IPR-R1 Triga Mark I Reactor located at the CDTN/CNEN, Belo Horizonte, Brazil, has been operating since November of 1960. In this work, measurements of thermal and epithermal neutron flux along the IPR-R1 neutron beam extractor were performed by neutron activation of reference materials using the two foils method. The obtained results were compared with results from two previous works: an experimental measurement done in a previous reactor core configuration and a numerical work made by Monte Carlo simulation using the actual reactor core configuration. The main purpose of this work is to update the measured data to the actual reactor core configuration. (author)

  20. Time Evolution of Selected Actinides in TRIGA MARK-II Fuel

    International Nuclear Information System (INIS)

    Usang, M.D.; Naim Shauqi Hamzah; Mohamad Hairie Rabir

    2011-01-01

    Study is made on the evolution of several actinides capable of undergoing fission or breeding available on the Malaysian Nuclear Agency (MNA) TRIGA MARK-II fuel. Population distribution of burned fuel in the MNA reactor is determined with a model developed using WIMS. This model simulates fuel conditions in the hottest position in the reactor, thus the location where most of the burn up occurs. Theoretical basis of these nuclide time evolution are explored and compared with the population obtained from our models. Good agreements are found for the theoretical time evolution and the population of Uranium-235, Uranium-236, Uranium-238 and Plutonium-239. (author)

  1. Radioactive waste management plan during the TRIGA Mark II and III decommissioning

    International Nuclear Information System (INIS)

    Jung, K.J.; Park, S.K.; Geong, G.H.; Lee, K.W.; Chung, U.S.; Paik, S.T.

    2001-01-01

    The decontamination and decommissioning (D and D) project of TRIGA Mark-I and Mark-II (KRR 1 and 2) was started in January 1997 and will be completed by December 2002. In the first year of the project, work was performed in preparation of the decommissioning plan, start of the environmental impact assessment and setup licensing procedure and documentation for the project with cooperation of the Korea Institute of Nuclear Safety (KINS). In the second year, Hyundai Engineering Company (HEC) with British Nuclear Fuels pie (BNFL) as technical assisting partner was designated as the contractor to do design and licensing documentation for the D and D of both reactors. After pre-design, a hazard and operability (HAZOP) study checked each step of the work. At the end of 1998, the decommissioning plan documentation including environmental impact assessment report was finished and submitted to the Ministry of Science and Technology (MOST) for licensing. It is expected to be issued by the end of September 1999. Practical work will then be started around the end of 1999. The safe treatment and management of the radioactive waste arising from the D and D activities is of utmost importance for successful completion of the practical dismantling work. This paper summarizes general aspects of radioactive waste treatment and management plan for the TRIGA Mark-I and II decommissioning work. (author)

  2. Treatment for dismantled radioactive solid waste from the TRIGA Mark-2 and 3

    International Nuclear Information System (INIS)

    Park, Seung Kook; Jung, Kyung Hwan

    1999-06-01

    Radioactive wastes are generally classified into 3 type depending on their physical property: liquid, solid and gaseous type. State-of -the art concerning liquid waste treatment has already been published; KAERI/TR-1315/99. Solid wastes classification package and treatment method will be studied to effectively manage them during the practical decommissioning work. All of the spent fuel produced during the operation of the TRIGA Mark-2 and 3 have been transported to the US last year, 1998, according to the spent fuel management strategy set-up by the US government for the non-proliferation of nuclear energy. Solid wastes are mainly all equipment existing inside of the reactors, activated concrete among the bio-shielded concrete, pipes, pimps, resin filter and it's housings, heat-exchangers, liquid waste storage tanks, to radioactive waste storage treatment facilities and so on. Solid wastes are generally low-level. They are classified according to the national regulation and nuclear law and IAEA Safety Standard Series ST-1(1996). Medium level radioactive wastes from reactor structures, mainly stainless steel component from the Rotary Specimen Rack(RSR) will be properly dismantled and stored in a shield container such as TIF(TRIGA Irradiated Fuel) container. While, low-level solid waste will be treated and packed in a ISO container(4m 3 ISO container for example) according to the IAEA recommendation. And combustible solid waste such as cloths, gloves, paper etc. will be packed in a 200 liters drum. This state-of-the art shows a general feature of the solid radioactive waste management which will be produced during the decommissioning of the TRIGA Mark-2 and 3 research reactors. (author). 17 refs., 17 tabs., 2 figs

  3. Criticality calculation in TRIGA MARK II PUSPATI Reactor using Monte Carlo code

    International Nuclear Information System (INIS)

    Rafhayudi Jamro; Redzuwan Yahaya; Abdul Aziz Mohamed; Eid Abdel-Munem; Megat Harun Al-Rashid; Julia Abdul Karim; Ikki Kurniawan; Hafizal Yazid; Azraf Azman; Shukri Mohd

    2008-01-01

    A Monte Carlo simulation of the Malaysian nuclear reactor has been performed using MCNP Version 5 code. The purpose of the work is the determination of the multiplication factor (k e ff) for the TRIGA Mark II research reactor in Malaysia based on Monte Carlo method. This work has been performed to calculate the value of k e ff for two cases, which are the control rod either fully withdrawn or fully inserted to construct a complete model of the TRIGA Mark II PUSPATI Reactor (RTP). The RTP core was modeled as close as possible to the real core and the results of k e ff from MCNP5 were obtained when the control fuel rods were fully inserted, the k e ff value indicates the RTP reactor was in the subcritical condition with a value of 0.98370±0.00054. When the control fuel rods were fully withdrawn the value of k e ff value indicates the RTP reactor is in the supercritical condition, that is 1.10773±0.00083. (Author)

  4. An analytical approach to the positive reactivity void coefficient of TRIGA Mark-II reactor

    International Nuclear Information System (INIS)

    Edgue, Erdinc; Yarman, Tolga

    1988-01-01

    Previous calculations of reactivity void coefficient of I.T.U. TRIGA Mark-II Reactor was done by the second author et al. The theoretical predictions were afterwards, checked in this reactor experimentally. In this work an analytical approach is developed to evaluate rather quickly the reactivity void coefficient of I.T.U. TRIGA Mark-II, versus the size of the void inserted into the reactor. It is thus assumed that the reactor is a cylindrical, bare nuclear system. Next a belt of water of 2πrΔrH is introduced axially at a distance r from the center line of the system. r here, is the thickness of the belt, and H is the height of the reactor. The void is described by decreasing the water density in the belt region. A two group diffusion theory is adopted to determine the criticality of our configuration. The space dependency of the group fluxes are, thereby, assumed to be J 0 (2.405 r / R) cos (π Z / H), the same as that associated with the original bare reactor uniformly loaded prior to the change. A perturbation type of approach, thence, furnishes the effect of introducing a void in the belt region. The reactivity void coefficient can, rather surprisingly, be indeed positive. To our knowledge, this fact had not been established, by the supplier. The agreement of our predictions with the experimental results is good. (author)

  5. Fuel burnup analysis of the TRIGA Mark II reactor at the University of Pavia

    International Nuclear Information System (INIS)

    Chiesa, Davide; Clemenza, Massimiliano; Pozzi, Stefano; Previtali, Ezio; Sisti, Monica; Alloni, Daniele; Magrotti, Giovanni; Manera, Sergio; Prata, Michele; Salvini, Andrea; Cammi, Antonio; Zanetti, Matteo; Sartori, Alberto

    2016-01-01

    Highlights: • A fuel evolution model for a TRIGA Mark II reactor has been developed. • Reproduction of nearly 50 years of reactor operation. • The model was used to predict the best reactor reconfiguration. • Reactor life was extended without adding fresh fuel elements. - Abstract: A time evolution model was developed to study fuel burnup for the TRIGA Mark II reactor at the University of Pavia. The results were used to predict the effects of a complete core reconfiguration and the accuracy of this prediction was tested experimentally. We used the Monte Carlo code MCNP5 to reproduce system neutronics in different operating conditions and to analyze neutron fluxes in the reactor core. The software that took care of time evolution, completely designed in-house, used the neutron fluxes obtained by MCNP5 to evaluate fuel consumption. This software was developed specifically to keep into account some features that differentiate low power experimental reactors from those used for power production, such as the daily ON/OFF cycle and the long fuel lifetime. These effects can not be neglected to properly account for neutron poison accumulation. We evaluated the effect of 48 years of reactor operation and predicted a possible new configuration for the reactor core: the objective was to remove some of the fuel elements from the core and to obtain a substantial increase in the Core Excess reactivity value. The evaluation of fuel burnup and the reconfiguration results are presented in this paper.

  6. Flow-induced vibration phenomenon in a Mark III TRIGA reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lee, C K; Whittemore, W L; Kim, B S; Lee, J B; Blevins, R D; Burton, T E [Korea Atomic Energy Research Institute, Seoul (Korea, Republic of); General Atomic Company, San Diego, CA (United States)

    1976-07-01

    The Mark III TRIGA reactor with hexagonal fuel spacing is capable of operating at 2.0 MW. The Mark III at San Diego operated without core cooling problems or vibration at power levels up to 2.0 MW. All Mark III reactors have operated trouble-free up to 1.0 MW. The Mark III TRIGA in Korea was installed in 1972 and operated many months without trouble at 2.0 MW. During this period core changes including addition of new fuel were made. Eighteen months after startup, a coolant flow-induced vibration was observed for the first time at a power of 1.5 MW. A lengthy series of tests showed that it was not possible to establish a core configuration that permitted vibration-free operation for power levels in the range 1.5 - 2.0 MW. Observations during the tests confirmed that standing waves in the reactor tank water coupled the source within the core to the shield structure and surrounding building. Analysis of the data indicates strongly that the source of the vibration is the creation and collapse of bubbles with the core acting as a resonator. A substantially increased flow of coolant through the upper grid plate is expected to eliminate the vibration phenomenon and permit trouble-free operation at power up to 2.0 MW. In an attempt to seek a remedy, both GAC and KAERI have independently developed designs for upper grid plates. KAERI has constructed and installed an interim version of the standard grid plate which was calculated to provide 25% more coolant flow and mounted high so as to provide less restriction to flow around the upper fittings of the fuel elements. A substantial reduction in vibration was observed. No vibration was observed at any power up to 2.0 MW with cooling water at or below 20 C. A slight vibration at 1.8 MW occurred for higher cooling temperatures. The GAC grid plate design provides not only for increasing the flow area but also for streamlining the flow surfaces on the grid plate and possibly also on the top fittings of the fuel elements. It is

  7. Flow-induced vibration phenomenon in a Mark III TRIGA reactor

    International Nuclear Information System (INIS)

    Lee, C.K.; Whittemore, W.L.; Kim, B.S.; Lee, J.B.; Blevins, R.D.; Burton, T.E.

    1976-01-01

    The Mark III TRIGA reactor with hexagonal fuel spacing is capable of operating at 2.0 MW. The Mark III at San Diego operated without core cooling problems or vibration at power levels up to 2.0 MW. All Mark III reactors have operated trouble-free up to 1.0 MW. The Mark III TRIGA in Korea was installed in 1972 and operated many months without trouble at 2.0 MW. During this period core changes including addition of new fuel were made. Eighteen months after startup, a coolant flow-induced vibration was observed for the first time at a power of 1.5 MW. A lengthy series of tests showed that it was not possible to establish a core configuration that permitted vibration-free operation for power levels in the range 1.5 - 2.0 MW. Observations during the tests confirmed that standing waves in the reactor tank water coupled the source within the core to the shield structure and surrounding building. Analysis of the data indicates strongly that the source of the vibration is the creation and collapse of bubbles with the core acting as a resonator. A substantially increased flow of coolant through the upper grid plate is expected to eliminate the vibration phenomenon and permit trouble-free operation at power up to 2.0 MW. In an attempt to seek a remedy, both GAC and KAERI have independently developed designs for upper grid plates. KAERI has constructed and installed an interim version of the standard grid plate which was calculated to provide 25% more coolant flow and mounted high so as to provide less restriction to flow around the upper fittings of the fuel elements. A substantial reduction in vibration was observed. No vibration was observed at any power up to 2.0 MW with cooling water at or below 20 C. A slight vibration at 1.8 MW occurred for higher cooling temperatures. The GAC grid plate design provides not only for increasing the flow area but also for streamlining the flow surfaces on the grid plate and possibly also on the top fittings of the fuel elements. It is

  8. Dynamics of TRIGA-3 Salazar Reactor.; Dinamica del Reactor TRIGA Mark III del Centro Nuclear de Mexico.

    Energy Technology Data Exchange (ETDEWEB)

    Gallardo S, L F

    1991-12-31

    The theoretical study of temporal behavior of a nuclear reactor is of great importance, since it allows to know, in advance, the conditions to which a reactor is going to be submitted. The reliability of two computer codes (AIREK-JEN and PLANKIN) designed to reproduce the temporal behavior of nuclear reactors, generally power reactors, when they are applied to reproduce the dynamic behavior of TRIGA-3 Salazar Reactor is analyzed. In the first chapters, the fundamental equations that solve this computer codes are deduced, and also the main characteristics of TRIGA-3 Salazar Reactor and the necessary data to run the programs are presented; later the results obtained with the computer codes and the experimental results reported in the operational logbook of the reactor are compared, with the result that such computer codes are applicable to the temporal study of TRIGA-3 Salazar Reactor. (Author).

  9. Immobilization of Ion Exchange radioactive resins of the TRIGA Mark III Nuclear Reactor; Inmovilizacion de resinas de intercambio ionico radiactivas del reactor nuclear TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Garcia Martinez, H

    1999-07-01

    In the last decades many countries in the world have taken interest in the use, availability, and final disposal of dangerous wastes in the environment, within these, those dangerous wastes that contain radioactive material. That is why studies have been made on materials used as immobilization agent of radioactive waste that may guarantee its storage for long periods of time under drastic conditions of humidity, temperature change and biodegradation. In mexico, the development of different applications of radioactive material in the industry, medicine and investigation, have generated radioactive waste, sealed and open sources, whose require a special technological development for its management and final disposal. The present work has as a finality to develop the process and define the agglutinating material, bitumen, cement and polyester resin that permits immobilization of resins of Ionic Exchange contaminated by Barium 153, Cesium 137, Europium 152, Cobalt 60 and Manganese 54 generated from the nuclear reactor TRIGA Mark III. Ionic interchange contaminated resin must be immobilized and is analysed under different established tests by the Mexican Official Standard NOM-019-NUCL-1995 {sup L}ow level radioactive wastes package requirements for its near-surface final disposal. Immobilization of ionic interchange contaminated resins must count with the International Standards applicable in this process; in these standards, the following test must be taken in prototype examples: Free-standing water, leachability, compressive strength, biodegradation, radiation stability, thermal stability and burning rate. (Author)

  10. Activation calculation of steel of the control rods of TRIGA Mark III reactor; Calculo de activacion del acero de las barras de control del reactor TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Garcia M, T.; Cruz G, H. S.; Ruiz C, M. A.; Angeles C, A., E-mail: teodoro.garcia@inin.gob.mx [ININ, Carretera Mexico-Toluca sn, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2014-10-15

    In the pool of TRIGA Mark III reactor of the Instituto Nacional de Investigaciones Nucleares (ININ), there are control rods that were removed from the core, and which are currently on shelves of decay. These rods were part of the reactor core when only had fuel standard (from 1968-1989). To conduct a proper activation analysis of the rods, is very important to have well-characterized the materials which are built, elemental composition of the same ones, the atomic densities and weight fractions of the elements that constitute them. To determine the neutron activation of the control rods MCNP5 code was used, this code allows us to have well characterized the radionuclides inventory that were formed during irradiation of the control rods. This work is limited to determining the activation of the steel that is part of the shielding of the control rods, the nuclear fuel that is in the fuel follower does not include. The calculation model of the code will be validated with experimental measurements and calculating the activity of fission products of the fuel follower which will take place at the end of 2014. (Author)

  11. Estimation of fast neutron fluence in steel specimens type Laguna Verde in TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Galicia A, J.; Francois L, J. L.; Aguilar H, F.

    2015-09-01

    The main purpose of this work is to obtain the fluence of fast neutrons recorded within four specimens of carbon steel, similar to the material having the vessels of the BWR reactors of the nuclear power plant of Laguna Verde when subjected to neutron flux in a experimental facility of the TRIGA Mark III reactor, calculating an irradiation time to age the material so accelerated. For the calculation of the neutron flux in the specimens was used the Monte Carlo code MCNP5. In an initial stage, three sheets of natural molybdenum and molybdenum trioxide (MoO 3 ) were incorporated into a model developed of the TRIGA reactor operating at 1 M Wth, to calculate the resulting activity by setting a certain time of irradiation. The results obtained were compared with experimentally measured activities in these same materials to validate the calculated neutron flux in the model used. Subsequently, the fast neutron flux received by the steel specimens to incorporate them in the experimental facility E-16 of the reactor core model operating at nominal maximum power in steady-state was calculated, already from these calculations the irradiation time required was obtained for values of the neutron flux in the range of 10 18 n/cm 2 , which is estimated for the case of Laguna Verde after 32 years of effective operation at maximum power. (Author)

  12. Simulation of TRIGA Mark II Benchmark Experiment using WIMSD4 and CITATION codes

    International Nuclear Information System (INIS)

    Dalle, Hugo Moura; Pereira, Claubia

    2000-01-01

    This paper presents a simulation of the TRIGA Mark II Benchmark Experiment, Part I: Steady-State Operation and is part of the calculation methodology validation developed to the neutronic calculation of the CDTN's TRIGA IPR - R1 reactor. A version of the WIMSD4, obtained in the Centro de Tecnologia Nuclear, in Cuba, was used in the cells calculation. In the core calculations was adopted the diffusion code CITATION. Was adopted a 3D representation of the core and the calculations were carried out at two energy groups. Many of the experiments were simulated, including, K eff , control rods reactivity worth, fuel elements reactivity worth distribution and the fuel temperature reactivity coefficient. The comparison of the obtained results, with the experimental results, shows differences in the range of the accuracy of the measurements, to the control rods worth and fuel temperature reactivity coefficient, or on an acceptable range, following the literature, to the K eff and fuel elements reactivity worth distribution and the fuel temperature reactivity coefficient. The comparison of the obtained results, with the experimental. results, shows differences in the range of the accuracy of the measurements, to the control rods worth and fuel temperature reactivity coefficient, or in an acceptable range, following the literature, to the K eff and fuel elements reactivity worth distribution. (author)

  13. Measurements of neutron flux distributions in the core of the Ljubljana TRIGA Mark II Reactor

    International Nuclear Information System (INIS)

    Rant, J.; Ravnik, M.; Mele, I.; Dimic, V.

    2008-01-01

    Recently the Ljubljana TRIGA Mark II Reactor has been refurbished and upgraded to pulsed operation. To verify the core design calculations using TRIGAP and PULSTR1 codes and to obtain necessary data for future irradiation and neutron beam experiments, an extensive experimental program of neutron flux mapping and neutron field characterization was carried out. Using the existing neutron measuring thimbles complete axial and radial distributions in two radial directions were determined for two different core configurations. For one core configuration the measurements were also carried out in the pulsed mode. For flux distributions thin Cu (relative measurements) and diluted Au wires (absolute values) were used. For each radial position the cadmium ratio was determined in two axial levels. The core configuration was rather uniform, well defined (fresh fuel of a single type, including fuelled followers) and compact (no irradiation channels or gaps), offering unique opportunity to test the computer codes for TRIGA reactor calculations. The neutron flux measuring procedures and techniques are described and the experimental results are presented. The agreement between the predicted and measured power peaking factors are within the error limits of the measurements (<±5%) and calculations (±10%). Power peaking occurs in the B ring, and in the A ring (centre) there is a significant flux depression. (authors)

  14. Detection of a leaking boron-carbide control rod in a TRIGA Mark I reactor

    Energy Technology Data Exchange (ETDEWEB)

    Blotcky, A J; Arsenault, L J [General Medical Research, Veterans Administration Hospital, Omaha (United States)

    1974-07-01

    During a routine quarterly inspection of the boron-carbide control rods of the Omaha Veterans Administration Hospital 18 kW Triga Mark I reactor, a pin hole leak was detected approximately 3 mm from the chamfered edge. The leak was found by observing bubbles when the rod was withdrawn from the reactor tank for visual observation, and could not be seen with the naked eye. This suggests that pin hole leaks could occur and not be visually detected in control rods and fuel elements examined underwater. A review of the rod calibrations showed that the leak had not caused a loss in rod worth. Slides will be presented showing the bubbles observed during the inspection, together with an unmagnified and magnified view of the pin hole. (author)

  15. Calculation of neutron fluxes in biological shield of the TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Bozic, M.; Zagar, T.; Ravnik, M.

    2001-01-01

    The complete calculation of neutron fluxes in biological shield and verification with experimental results is presented. Calculated results are obtained with TORT code (TORT-Three Dimensional Oak Ridge Discrete Ordinates Neutron/Photon Transport Code). Experimental results used for comparison are available from irradiation experiment with selected type of concrete and other materials in irradiation channel 4 in TRIGA Mark II reactor. These experimental results were used as a benchmark. Homogeneous type of problem (without inserted irradiation channel) and problem with asymmetry (inserted beam port 4, filled with different materials) were of interest for neutron flux calculation. Deviation from material data set up as original parameters is also considered (first of all presence of water in concrete and density of concrete) for type of concrete in biological shield and for selected type of concrete in irradiation channel. BUGLE-96 (47 neutron energy groups) library is used. Excellent agreement between calculated and experimental results for reaction rate is received.(author)

  16. Detection of a leaking boron-carbide control rod in a TRIGA Mark I reactor

    International Nuclear Information System (INIS)

    Blotcky, A.J.; Arsenault, L.J.

    1974-01-01

    During a routine quarterly inspection of the boron-carbide control rods of the Omaha Veterans Administration Hospital 18 kW Triga Mark I reactor, a pin hole leak was detected approximately 3 mm from the chamfered edge. The leak was found by observing bubbles when the rod was withdrawn from the reactor tank for visual observation, and could not be seen with the naked eye. This suggests that pin hole leaks could occur and not be visually detected in control rods and fuel elements examined underwater. A review of the rod calibrations showed that the leak had not caused a loss in rod worth. Slides will be presented showing the bubbles observed during the inspection, together with an unmagnified and magnified view of the pin hole. (author)

  17. Neutron spectra in two beam ports of a TRIGA Mark III reactor with HEU fuel

    International Nuclear Information System (INIS)

    Vega C, H. R.; Hernandez D, V. M.; Paredes G, L.; Aguilar, F.

    2012-10-01

    Before to change the HEU for Leu fuel of the ININ's TRIGA Mark III nuclear reactor the neutron spectra were measured in two beam ports using 5 and 10 W. Measurements were carried out in a tangential and a radial beam port using a Bonner sphere spectrometer. It was found that neutron spectra are different in the beam ports, in radial beam port the amplitude of thermal and fast neutrons are approximately the same while, in the tangential beam port thermal neutron peak is dominant. In the radial beam port the fluence-to-ambient dose equivalent factors are 131±11 and 124±10 p Sv-cm 2 for 5 and 10 W respectively while in the tangential beam port the fluence-to-ambient dose equivalent factor is 55±4 p Sv-cm 2 for 10 W. (Author)

  18. Non-destructive material investigation with thermal neutrons at the TRIGA Mark II reactor in Vienna

    International Nuclear Information System (INIS)

    Bastuerk, M.; Boeck, H.; Zamani, B.; Zawisky, M.; Rauch, H.

    2004-01-01

    Neutron tomography providing 3D information about interior of an object is a very efficient tool to visualize inner defects of the materials, non-destructively. In this study, some applications of neutron tomography in different fields such as geology, aerospace, civil engineering and archaeology were presented. Distribution of minerals in pumice and rock samples, visualization of inner defects within a new developed titan aluminum turbine blade, and distribution of silica gel as an important impregnating agent in construction and restoration of buildings were investigated. The measurements of tomography projections taken in the 0 to 180 o angle were performed with a thermal neutron flux of 10 5 at the TRIGA Mark II research reactor in Vienna, and the common filtered back projection method was used for the 3D image reconstruction. (author)

  19. TRIGASIM: A computer program to simulate a TRIGA Mark I Reactor

    International Nuclear Information System (INIS)

    Ruby, Lawrence

    1992-01-01

    A Fortran-77 computer program has been written which simulates the operation of a TRIGA Mark I Reactor. The 'operator' has options at 1-second intervals, of raising rods, lowering rods, maintaining rods steady, dropping a rod, or scramming the reactor. Results are printed to the screen, and to 2 output files - a tabular record and a logarithmic plot of the power. The Point Kinetic Equations are programmed with 6 delayed groups, quasi-static power feedback, and forward differencing. A pulsing option is available, with simulation which employs the Fuchs Model. A pulse-tail model has been devised to simulate behavior for a few minutes following a pulse. Both graphic and tabular output are also available for the pulses. (author)

  20. Experimental measurement of the refrigerant temperature of the TRIGA Mark III reactor of the ININ

    International Nuclear Information System (INIS)

    Gallardo S, L.F.; Alonso V, G.

    1991-08-01

    With the object of knowing the axial temperature profile of the refrigerant in the core of the TRIGA Mark III reactor of the ININ, the temperatures of this, at the enter, in the center and the exit of the core were measured, in the positions: west 2, north 2 and south 1. This was made by means of the thermo pars introduction mounted in aluminum guides, connected to a measurer of digital temperature, whose resolution is of ± 0.1 C. The measurements showed a bigger heating of the refrigerant in the superior half of the core, that which suggests that the axial profile of temperature of the reactor is not symmetrical with respect to the center or that those temperature measurements in the center are not correct. (Author)

  1. Present Services at the TRIGA Mark II Reactor of the JSI

    International Nuclear Information System (INIS)

    Smodiš, B.; Snoj, L.

    2013-01-01

    The TRIGA Mark II research reactor of the Jožef Stefan Institute has been continuously operating since the year 1966. The currently offered services include: (1) Neutron activation analysis in both instrumental and radiochemical modes; (2) neutron irradiation of various kinds of materials intended to be used for research and applicative purposes; (3) training and education of university students as well as on-job training of staff working in public and private institutions, (4) verification of computer codes and nuclear data, comprising primarily criticality calculations and neutron flux distribution studies and (5) testing and development of a digital reactivity meter. The paper briefly describes the aforementioned activities and shows that even such small reactors are still indispensable in nuclear science and technology. (author)

  2. Nine years of operation of ITU-TRR TRIGA Mark-II reactor

    International Nuclear Information System (INIS)

    Yavuz, H.; Bayuelken, A.R.; Yavuz, M.A.

    1988-01-01

    ITU-TRR TRIGA Mark-II reactor in Istanbul with a steady state power of 250 kW and a pulsing capability up to 1200 MW has been operating since March 11,1979 with an energy release of 107.5 MWh and a total of 72 pulses. During this nearly nine years, the reactor was in operation without any major undesired shut down. One of the major problems was faced when the instrumented fuel element in position 9 of the F ring went totally out of order. Secondly, the cooling tower of the secondary cooling system could not be operated properly during the hot summer days, and also we had a tar leakage problem with the radial beam port connection to the tank. During the regular maintenance work in this summer, the measurements of changes in nuclear and physical parameters of the reactor fuel and dummy elements have also proceeded. (author)

  3. Startup of Torrey Pines Mark III and Puerto Rico Nuclear Center reactors with TRIGA-FLIP fuel

    Energy Technology Data Exchange (ETDEWEB)

    Chesworth, R. H. [Gulf E and ES, San Diego, CA (United States)

    1972-07-01

    This paper discusses the characteristics of TRIGA FLIP cores in two different geometries: the normal TRIGA single-rod geometry as typified by the installation in the Torrey Pines Mark III reactor; and the four-rod cluster geometry as typified by the conversion core installed in the Puerto Rico Nuclear Center reactor at Mayaguez. In both reactors the fuel is 8-1/2 wt % uranium, 70% enriched in U-235. The hydrogen to zirconium atom ratio is 1.5 to 1.65 and the cladding material is stainless steel. The basic neutronic characteristics of the fuel in both reactor installations are briefly discussed.

  4. A digital data acquisition and display system for ITU TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Can, B.; Omuz, S.

    2008-01-01

    Full text: In this study, a digital data acquisition and display system realized for ITU TRIGA Mark-II Reactor is described. This system is realized in order to help the reactor operator and to increase reactor console capacity. The system consists of two main units, which are host computers and RTI-815F, analog devices, data acquisition card. RTI-815F is multi-function analog/digital input/output board that plugs into one of the available long expansion slots in the IBM-PC, PC/XT, PC/AT, or equivalent personal computers. It has 16 analog input channels for single-ended input signals or 8 analog input channels for differential input signals. But its channel capacity can be increased to 32 input channels for single-ended input signals or 16 input channels for differential input signals. RTI-815F board contains 2 analog output channels, 8 digital input channels and 8 digital output channels. In the ITD TRIGA Mark-II Reactor, 6 fuel temperature channels, 3 water temperature channels, 3 control rod position channels and 4 power channels are chosen as analog input signals for RTI-815F. Its digital outputs are assigned to cooling tower fan, primary and secondary pump reactor scram, control rod rundown. During operation, data are automatically archived to disk and displayed on screen. The channel selection time and sampling time can be adjusted. The simulated movement and position of control rods in the reactor core can be noted and displayed. The changes of power, fuel temperature and water temperature can be displayed on the screen as a graphic. In this system both period and reactivity are calculated and displayed on the screen. (authors)

  5. Neutron radiography applications in I.T.U. TRIGA Mark-II reactor

    International Nuclear Information System (INIS)

    Tugrul, A. B.

    2002-01-01

    Neutron radiography is an important radiographic technique which is supplied different and advanced information according to the X or gamma ray radiography. However, it has a trouble for supplying the convenient neutron sources. Tangential beam tube of Istanbul Technical University (ITU) TRIGA Mark-II Training and Research Reactor has been arranged for using neutron radiography. The neutron radiography set defined as detailed for the application of the technique. Two different techniques for neutron radiography are defined as namely, transfer method and direct method. For the transfer method dysprosium and indium screens are used in the study. But, dysprosium generally was preferred in many studies in the point of view nuclear safety. Gadolinium was used for direct method. Two techniques are compared and explained the preferring of the transfer technique. Firstly, reference composition is prepared for seeing the differences between neutron and X-ray or gamma radiography. In addition of it, some radiograph samples are given neutron and X-ray radiography which shows the different image characters. Lastly, some examples are given from archaeometric studies. One of them the brass plates of Great Mosque door in Cizre. After the neutron radiography application, organic dye traces are noticed. Other study is on a sword that belong to Urartu period at the first millennium B.C. It is seen that some wooden part on it. Some different artefacts are examined with neutron radiography from the Ikiztepe excavation site, then some animal post parts are recognized on them. One of them is sword and sheath which are corroded together. After the neutron radiography application, it can be noticed that there are a cloth between the sword and its sheath. By using neutron radiography, many interesting and detailed results are observed in ITU TRIGA Mark-II Training and Research Reactor. Some of them shouldn't be recognised by using any other technique

  6. Archaeometric studies by using neutron radiography in ITU TRIGA Mark-II reactor

    International Nuclear Information System (INIS)

    Tugrul, A. Beril

    2008-01-01

    Archaeometric many studies have been done by using neutron radiography in ITU TRIGA Mark-II Training and Research Reactor for over 15 years. Tangential beam tube has been arranged for using neutron radiography. Generally, transfer technique has been preferred with using dysprosium screen, but indium screen also is used. Some studies are described which are all on the Anatolian artefacts. The first study from 13th century AD deals with Seljukian period from south-east Anatolia. It investigated a plate from Great Mosque door in Cizre. With means of the neutron radiography painting traces are investigated on the plates. Organic dye traces are noticed on some of plates, which have generally animal figures. Other studies from Urartu period at the first millennium B.C, investigates artefacts found at the vicinity of Van on east Anatolia. An important one is a sword that was found in a grave. It has some corrosion defects. The neutron radiography was applied and shown that wooden parts are there. Other studies referred to samples from the Ikiztepe Excavation site on north Anatolia. Many artefacts were examined by neutron radiography. Some of them evidenced animal parts are recognised as covering parts. An interesting result was obtained to a sword and its sheath that were corroded together. After the neutron radiography applications, it was noticed that there are a cloth between the sword and its sheath. Hence, it was the cause of corrosion of the artefact. By using neutron radiography, many interesting and detailed results were observed by means of the neutron beam from the ITU TRIGA Mark-II Training and Research Reactor. Some of them could not be evidenced by means of any other technique

  7. Modernization of the facilities of the TRIGA Mark III reactor of ININ; Modernizacion de las instalaciones del reactor TRIGA Mark III del ININ

    Energy Technology Data Exchange (ETDEWEB)

    Mendez T, D.; Flores C, J., E-mail: dario.mendez@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2016-09-15

    The TRIGA Mark III reactor of the Instituto Nacional de Investigaciones Nucleares (ININ) has been in operation since 1968 under strict maintenance and component replacement programs, which has allowed its safe operation during this time. Under this scheme, the reactor was operating under suitable conditions, taking into account the different requests for operation that were received for the samples irradiation for the radioisotopes production such as the Sm-153, personnel training, basic research, archaeology and environmental studies and nuclear chemistry of the elements. However, a modernization program of its components and laboratories was required, in order to improve safety in the operation of the same and to increase its use in the analysis of samples by neutron activation and in the training of personnel. This program known as Modernization Program of the Reactor Facilities, was proposed alongside the project to replace high-enrichment fuels with low-enrichment fuels at the end of 2011 and early 2012. The central aspects of this program are described in this work, grouped into generic topics that include instrumentation and control, the radiological monitoring system of the area, the cooling system, the ventilation system, the neutron activation analysis laboratory, the manufacture of graphite elements, inspection submersible system of the pool, temporary storage system for irradiated fuels, traveling crane, Reactor support laboratories and technical meetings, courses and seminars for reactor personnel and associated groups. It also describes some of the most relevant components required for each system and the progress that is made in each one of them. As a fundamental result of the implementation of this Modernization Program of the Reactor Facilities, there has been a substantial improvement in the performance of the systems and components of its facilities, in the reliability of its operation and in the safety of the same. (Author)

  8. Adaptive fuzzy control of neutron power of the TRIGA Mark III reactor; Control difuso adaptable de la potencia neutronica del reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Rojas R, E.

    2014-07-01

    The design and implementation of an identification and control scheme of the TRIGA Mark III research nuclear reactor of the Instituto Nacional de Investigaciones Nucleares (ININ) of Mexico is presented in this thesis work. The identification of the reactor dynamics is carried out using fuzzy logic based systems, in which a learning process permits the adjustment of the membership function parameters by means of techniques based on neural networks and bio-inspired algorithms. The resulting identification system is a useful tool that allows the emulation of the reactor power behavior when different types of insertions of reactivity are applied into the core. The identification of the power can also be used for the tuning of the parameters of a control system. On the other hand, the regulation of the reactor power is carried out by means of an adaptive and stable fuzzy control scheme. The control law is derived using the input-output linearization technique, which permits the introduction of a desired power profile for the plant to follow asymptotically. This characteristic is suitable for managing the ascent of power from an initial level n{sub o} up to a predetermined final level n{sub f}. During the increase of power, a constraint related to the rate of change in power is considered by the control scheme, thus minimizing the occurrence of a safety reactor shutdown due to a low reactor period value. Furthermore, the theory of stability in the sense of Lyapunov is used to obtain a supervisory control law which maintains the power error within a tolerance region, thus guaranteeing the stability of the power of the closed loop system. (Author)

  9. Applicable regulations and development of surveillance experiments of criticality approach in the TRIGA III Mark reactor; Normativa aplicable y desarrollo de experimentos de vigilancia de aproximacion a criticidad en el reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez M, J L; Aguilar H, F; Rivero G, T; Sainz M, E [Instituto nacional de Investigaciones Nucleares, Departamento de Automatizacion, A.P. 18-1027, Col. Escandon, 11801 Mexico D.F. (Mexico)

    2000-07-01

    In the procedure elaborated to repair the vessel of TRIGA III Mark reactor is required to move toward two tanks of temporal storage the fuel elements which are in operation and the spent fuel elements which are in decay inside the reactor pool. The National Commission of Nuclear Safety and Safeguards (CNSNS) has requested as protection measure that it is carried out a surveillance of the criticality approach of the temporal storages. This work determines the main regulation aspects that entails an experiment of criticality approach, moreover, informing about the results obtained in the developing of this experiments. The regulation aspects are not exclusives for this work in the TRIGA Mark III reactor but they also apply toward any assembling of fissile material. (Author)

  10. Adaptive control method for core power control in TRIGA Mark II reactor

    Science.gov (United States)

    Sabri Minhat, Mohd; Selamat, Hazlina; Subha, Nurul Adilla Mohd

    2018-01-01

    The 1MWth Reactor TRIGA PUSPATI (RTP) Mark II type has undergone more than 35 years of operation. The existing core power control uses feedback control algorithm (FCA). It is challenging to keep the core power stable at the desired value within acceptable error bands to meet the safety demand of RTP due to the sensitivity of nuclear research reactor operation. Currently, the system is not satisfied with power tracking performance and can be improved. Therefore, a new design core power control is very important to improve the current performance in tracking and regulate reactor power by control the movement of control rods. In this paper, the adaptive controller and focus on Model Reference Adaptive Control (MRAC) and Self-Tuning Control (STC) were applied to the control of the core power. The model for core power control was based on mathematical models of the reactor core, adaptive controller model, and control rods selection programming. The mathematical models of the reactor core were based on point kinetics model, thermal hydraulic models, and reactivity models. The adaptive control model was presented using Lyapunov method to ensure stable close loop system and STC Generalised Minimum Variance (GMV) Controller was not necessary to know the exact plant transfer function in designing the core power control. The performance between proposed adaptive control and FCA will be compared via computer simulation and analysed the simulation results manifest the effectiveness and the good performance of the proposed control method for core power control.

  11. Development and validation of a model TRIGA Mark III reactor with code MCNP5

    International Nuclear Information System (INIS)

    Galicia A, J.; Francois L, J. L.; Aguilar H, F.

    2015-09-01

    The main purpose of this paper is to obtain a model of the reactor core TRIGA Mark III that accurately represents the real operating conditions to 1 M Wth, using the Monte Carlo code MCNP5. To provide a more detailed analysis, different models of the reactor core were realized by simulating the control rods extracted and inserted in conditions in cold (293 K) also including an analysis for shutdown margin, so that satisfied the Operation Technical Specifications. The position they must have the control rods to reach a power equal to 1 M Wth, were obtained from practice entitled Operation in Manual Mode performed at Instituto Nacional de Investigaciones Nucleares (ININ). Later, the behavior of the K eff was analyzed considering different temperatures in the fuel elements, achieving calculate subsequently the values that best represent the actual reactor operation. Finally, the calculations in the developed model for to obtain the distribution of average flow of thermal, epithermal and fast neutrons in the six new experimental facilities are presented. (Author)

  12. Computational analysis of neutronic parameters of CENM TRIGA Mark II research reactor

    International Nuclear Information System (INIS)

    El Younoussi, C.; El Bakkari, B.; Boulaich, Y.; Riyach, D.; Otmani, S.; Marrhich, I.; Badri, H.; Htet, A.; Nacir, B.; El Bardouni, T.; Boukhal, H.; Zoubair, M.; Ossama, M.; Chakir, E.

    2010-01-01

    The CENM TRIGA MARK II reactor is part of the National Center for Energy, Sciences and Nuclear Techniques (CNESTEN). It's a standard design 2MW, natural-convection-cooled reactor with a graphite reflector containing 4 beam tubes and a thermal column. The reactor has several applications in different fields as industry, agriculture, medicine, training and education. In the present work a computational study has been carried out in the framework of neutronic parameters studies of the reactor. A detailed MCNP model that include all elements of the core and surrounding structures has been developed to calculate different parameters of the core (The effective multiplication factor, reactivity experiments comprising control rods worth, excess reactivity and shutdown margin). Further calculations have been carried out to calculate the neutron flux profiles at different locations of the reactor core. The cross sections used are processed from the library provided with MCNP5 and based on the ENDF/B-VII with continuous dependence in energy and special treatment of thermal neutrons in lightweight materials. (author)

  13. IPR-RI TRIGA MARK I reactor and the neutron activation analysis at CDTN/CNEN

    International Nuclear Information System (INIS)

    Menezes, Maria Angela de B.C.; Kastner, Geraldo F.; Amaral, Angela M.; Souza, Wagner de; Maretti, Fausto Junior; Leal, Alexandre S.

    2008-01-01

    The IPR-R1 TRIGA Mark I research reactor started up in 1960. It is located at Centro de Desenvolvimento da Tecnologia Nuclear (Nuclear Technology Development Centre) / Comissao Nacional de Energia Nuclear (Brazilian Commission for Nuclear Energy), CDTN/CNEN. Join to the reactor, the Laboratory for Neutron Activation Analysis has been developing its activities since 1960. The activities of the Laboratory comprise the delayed fission neutron activation analysis, instrumental (comparative and parametric methods) and radiochemical / chemical methods. These methods are responsible for relevant percentage of CDTN's analysis demand, meeting the clients' analytical needs and researches developed by the Laboratory, by CDTN and by other institutions. Over the years the work has been linked to the goals of the country and the institutions. Nowadays several elements - Ag, Al, Au, As, Ba, Br, Ca, Cd, Ce, Cl, Co, Cr, Cs, Cu, Dy, Eu, Fe, Ga, Hf, Hg, Ho, K, La, Mg, Mn, Mo, Na, Nd, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, Ti, U, V, W, Yb, Zn and Zr - are determined in several matrices and range of concentrations. In Brazil, CDTN is the only Institute that fully masters the instrumental neutron activation analysis k0-method determining short, medium and long half-life radionuclides using its own nuclear reactor. The good performance of the reactor is pointed out in a table with experimental and certified values for Certified Reference Materials. (authors)

  14. Conversion of the core of the TRIGA Mark III reactor at the Mexican Nuclear Centre

    International Nuclear Information System (INIS)

    Moran Lopez, J.M.; Lucatero, M.A.; Reyes Andrade, B.; Rivero Gutierrez, T.; Sainz Mejia, E.

    1990-01-01

    It was decided to convert the core of the TRIGA MARK III reactor at the Mexican Nuclear Centre run by the National Nuclear Institute because of problems detected during the operation, such as a lack of excess reactivity for operation at nominal power over long periods and difficulties in the maintenance and calibration of the control panel. In order to compensate for the lack of excess reactivity the fuel elements taken to the highest burnup were replaced by fresh elements acquired for this purpose. The latter, however, had a different enrichment, and this necessitated a detailed analysis of the neutronic and thermohydraulic behaviour of the reactor with a view to determining a mixed core configuration which would meet safe operation requirements. In conducting the thermohydraulic analysis, a natural convection coolant flow model was developed to determine coolant velocity and pressure drop patterns within the core. The heat transfer equations were solved and it was found that the hottest fuel element did not attain critical heat flux conditions. In loading this core it was also necessary to analyse procedures and to consider the possible effects of reaching criticality with fuel elements having different enrichments. The loading procedure is described, as is the measurement system and the results obtained. In order to resolve the calibration and maintenance problems, a new, more advanced control panel was designed with conventional and nuclear detection systems and modern components

  15. Calculation analysis of TRIGA MARK II reactor core composed of two types of fuel elements

    International Nuclear Information System (INIS)

    Ravnik, M.

    1988-11-01

    The most important properties of mixed cores are treated for TRIGA MARK II reactor, composed of standard (20% enriched, 8.5w% U content) and FLIP (70% enriched, 8.5w% U content) fuel elements. Large difference in enrichment and presence of burnable poison in FLIP fuel have strong influence on the main core characteristics, such as: fuel temperature coefficient, power defect, Xe and Sm worth, power and flux distributions, etc. They are significantly different for both types of fuel. Optimal loading of mixed cores therefore strongly depends on the loading pattern of both types of fuel elements. Results of systematic calculational analysis of mixed cores are presented. Calculations on the level of fuel element are performed with WIMSD-4 computer code with extended cross-section library. Core calculations are performed with TRIGAP two-group 1-D diffusion code. Results are compared to measurements and physical explanation is provided. Special concern is devoted to realistic mixed cores, for which optimal in-core fuel management is derived. Refs, figs and tabs

  16. Damage analysis of TRIGA MARK II Bandung reactor tank material structure

    International Nuclear Information System (INIS)

    Soedardjo; Sumijanto

    2000-01-01

    Damage of Triga Mark II Bandung reactor tank material structure has been analyzed. The analysis carried out was based on ultrasonic inspection result in 1996 and the monthly reports of reactor operation by random data during 1988 up to 1995. Ultrasonic test data had shown that thinning processes on south and west region of reactor out side wall at upper part of water level had happened. Reactor operation data had shown the demineralized water should be added monthly to the reactor and bulk shielding water tank. Both reactor and bulk shielding tank are shielded by concrete of Portland type I cement consisting of CaO content about 58-68 %. The analysis result shows that the reaction between CaO and seepage water from bulk shielding wall had taken place and consequently the reactor out sidewall surroundings became alkaline. Based on Pourbaix diagram, the aluminum reactor tank made of aluminum alloy 6061 T6 would be corroded easily at pH equal an greater than 8.6. The passive layer AI 2 O 3 aluminum metal surface would be broken due to water reaction taken place continuously at high pH and produces hydrogen gas. The light hydrogen gas would expand the concrete cement and its expanding power would open the passive layer of aluminum metal upper tank. The water sea pages from adding water into reactor tank could indicate the upper water level tank corrosion is worse than the lower water level tank. (author)

  17. Testing the applicability of the k 0-NAA method at the MINT's TRIGA MARK II reactor

    International Nuclear Information System (INIS)

    Siong, Wee Boon; Dung, Ho Manh; Wood, Ab. Khalik; Salim, Nazaratul Ashifa Abd.; Elias, Md. Suhaimi

    2006-01-01

    The Analytical Chemistry Laboratory at MINT is using the NAA technique since 1980s and is the only laboratory in Malaysia equipped with a research reactor, namely the TRIGA MARK II. Throughout the years the development of NAA technique has been very encouraging and was made applicable to a wide range of samples. At present, the k 0 method has become the preferred standardization method of NAA (k 0 -NAA) due to its multi-elemental analysis capability without using standards. Additionally, the k 0 method describes NAA in physically and mathematically understandable definitions and is very suitable for computer evaluation. Eventually, the k 0 -NAA method has been adopted by MINT in 2003, in collaboration with the Nuclear Research Institute (NRI), Vietnam. The reactor neutron parameters (α and f) for the pneumatic transfer system and for the rotary rack at various locations, as well as the detector efficiencies were determined. After calibration of the reactor and the detectors, the implemented k 0 method was validated by analyzing some certified reference materials (including IAEA Soil 7, NIST 1633a, NIST 1632c, NIST 1646a and IAEA 140/TM). The analysis results of the CRMs showed an average u score well below the threshold value of 2 with a precision of better than ±10% for most of the elemental concentrations obtained, validating herewith the introduction of the k 0 -NAA method at the MINT

  18. Testing the applicability of the k0-NAA method at the MINT's TRIGA MARK II reactor

    Science.gov (United States)

    Siong, Wee Boon; Dung, Ho Manh; Wood, Ab. Khalik; Salim, Nazaratul Ashifa Abd.; Elias, Md. Suhaimi

    2006-08-01

    The Analytical Chemistry Laboratory at MINT is using the NAA technique since 1980s and is the only laboratory in Malaysia equipped with a research reactor, namely the TRIGA MARK II. Throughout the years the development of NAA technique has been very encouraging and was made applicable to a wide range of samples. At present, the k0 method has become the preferred standardization method of NAA ( k0-NAA) due to its multi-elemental analysis capability without using standards. Additionally, the k0 method describes NAA in physically and mathematically understandable definitions and is very suitable for computer evaluation. Eventually, the k0-NAA method has been adopted by MINT in 2003, in collaboration with the Nuclear Research Institute (NRI), Vietnam. The reactor neutron parameters ( α and f) for the pneumatic transfer system and for the rotary rack at various locations, as well as the detector efficiencies were determined. After calibration of the reactor and the detectors, the implemented k0 method was validated by analyzing some certified reference materials (including IAEA Soil 7, NIST 1633a, NIST 1632c, NIST 1646a and IAEA 140/TM). The analysis results of the CRMs showed an average u score well below the threshold value of 2 with a precision of better than ±10% for most of the elemental concentrations obtained, validating herewith the introduction of the k0-NAA method at the MINT.

  19. Estimation development cost, study case: Quality Management System Reactor TRIGA Mark III

    International Nuclear Information System (INIS)

    Antúnez Barbosa, Tereso Antonio; Valdovinos Rosas, Rosa María; Marcial Romero, José Raymundo; Ramos Corchado, Marco Antonio; Edgar Herrera Arriaga

    2016-01-01

    The process of estimating costs in software engineering is not a simple task, it must be addressed carefully to obtain an efficient strategy to solve problems associated with the effort, cost and time of activities that are performed in the development of an information system project. In this context the main goal for both developers and customers is the cost, since developers are worry about the effort pay-load and customers are worry about the product pay-load. However, in other fields the cost of goods depends on the activity or process that is performed, thereby deduce that the main cost of the final product of a development project software project is undoubtedly its size. In this paper a comparative study of common models for estimating costs are developed. These models are used today in order to create a structured analysis to provide the necessary information about cost, time and effort for making decisions in a software development project. Finally the models are applied to a case study, which is a system called Monitorizacion Automatica del Sistema de Gestion de Calidad del Reactor TRIGA Mark III. (author)

  20. Thermal Hydraulics Analysis for the 3MW TRIGA MARK-II Research Reactor Under Transient Condition

    International Nuclear Information System (INIS)

    Huda, M.Q.; Bhuiyan, S.I.; Mondal, M.A.W.

    1996-12-01

    Some important thermal hydraulic parameters of the 3 MW TRIGA MARK-II research reactor operating under transient condition were investigated using two computer codes PULTRI and TEMPUL. Major transient parameters, such as, peak power and prompt energy released after pulse, maximum fuel and coolant temperature, surface heat flux, time and radial distribution of temperature within fuel element after pulse, fuel, fuel-cladding gap width variation, etc. were computer and compared with the experimental and operational values as reported in the safety Analysis Report (SAR). It was observed that pulsing of the reactor inserting an excess reactivity of $2.00 shoots the reactor power level to 854.353 MW compared to an experimental value of 852 MW; the maximum fuel temperature corresponding to this peak power was found to be 846.76 o C which is much less than the limiting maximum value of fuel temperature of 1150 0 C as reported in SAR. During a pulse if the film boiling occurs for a peak adiabatic fuel temperature of 1000 o C, the calculated outer cladding wall temperature was observed to be 702.39 0 C compared to a value of 760 o C reported in SAR under the same condition. The investigated other results were also found to be in good agreement with the values reported in the SAR. 16 refs., 22 figs. (author)

  1. Neutron spectra in two beam ports of the TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Vega C, H. R.; Hernandez D, V. M.; Aguilar, F.; Paredes, L.; Rivera M, T.

    2013-10-01

    The neutron spectra have been measured in two beam ports, radial and tangential, of the TRIGA Mark III nuclear reactor from the National Institute of Nuclear Research. Measurements were carried out with the core with mixed fuel (Leu 8.5/20 and Flip Heu 8.5/70). Two reactor powers, 5 and 10 W, were used during neutron spectra measurements using a Bonner sphere spectrometer with a 6 Lil(Eu) scintillator and 2, 3, 5, 8, 10 and 12 inches-diameter high density polyethylene spheres. The neutron spectra were unfolded using the NSDUAZ unfolding code; from each spectrum the total neutron flux, the neutron mean energy and the neutron ambient dose equivalent dose were determined. Measured spectra show fission (E≥ 0.1 MeV), epithermal (from 0.4 eV up to 0.1 MeV) and thermal neutrons (E≤ 0.4 eV). For both reactor powers the spectra in the radial beam port have similar features which are different to the neutron spectrum characteristics in the tangential beam port. (Author)

  2. Neutron detection of the Triga Mark III reactor, using nuclear track methodology

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa, G., E-mail: espinosa@fisica.unam.mx; Golzarri, J. I. [Instituto de Física, Universidad Nacional Autónoma de México Circuito de la Investigación Científica, Ciudad Universitaria. México, DF (Mexico); Raya-Arredondo, R.; Cruz-Galindo, S. [Instituto Nacional de Investigaciones Nucleares (Mexico); Sajo-Bohus, L. [Universidad Simón Bolivar, Laboratorio de Física Nuclear, Caracas (Venezuela, Bolivarian Republic of)

    2015-07-23

    Nuclear Track Methodology (NTM), based on the neutron-proton interaction is one often employed alternative for neutron detection. In this paper we apply NTM to determine the Triga Mark III reactor operating power and neutron flux. The facility nuclear core, loaded with 85 Highly Enriched Uranium as fuel with control rods in a demineralized water pool, provide a neutron flux around 2 × 10{sup 12} n cm{sup −2} s{sup −1}, at the irradiation channel TO-2. The neutron field is measured at this channel, using Landauer{sup ®} PADC as neutron detection material, covered by 3 mm Plexiglas{sup ®} as converter. After exposure, plastic detectors were chemically etched to make observable the formed latent tracks induced by proton recoils. The track density was determined by a custom made Digital Image Analysis System. The resulting average nuclear track density shows a direct proportionality response for reactor power in the range 0.1-7 kW. We indicate several advantages of the technique including the possibility to calibrate the neutron flux density measured at low reactor power.

  3. The IPR-R1 TRIGA Mark I Reactor in 39 years: Operations and general improvements

    International Nuclear Information System (INIS)

    Maretti Junior, Fausto; Prado Fernandes, Marcio; Oliveira, Paulo Fernando; Alves de Amorim, Valter

    1999-01-01

    The nuclear IPR-R1 TRIGA Mark I Reactor operating in the Nuclear Technology Development Center, originally Institute for Radioactive Research in Minas Gerais, Brazil, was dedicated in November 11, 1960. Initially operating for the production of radioisotopes for different uses, it started later to be used in large scale for neutron activation analysis and training of operators for nuclear power plants. Many improvements have been made throughout these years to provide a better performance in its operation and safety conditions. A new cooling system to operate until 300 kW, a new control rod mechanism, an aluminum tank for the reactor pool, an optimization in the pneumatic system, a new reactor control console and a general remodeling of the reactor laboratory were some of the improvements added. To prevent and mitigate the ageing effects, the reactor operation personnel is starting a program to minimize future operation problems. This paper describes the improvements made, the results obtained during the past 39 years, and the precautions taken to ensure future safe operation of the reactor to give operators better conditions of safe work. (author)

  4. Boron Neutron Capture Therapy activity of diffused tumors at TRIGA Mark II in Pavia

    Energy Technology Data Exchange (ETDEWEB)

    Bortolussi, S.; Stella, S.; De Bari, A.; Altieri, S. [Department of Nuclear and Theoretical Physics, University of Pavia, Pavia (Italy)]|[National Institute of Nuclear Physics (INFN), Pavia (Italy); Bruschi, P.; Bakeine, J.G. [Department of Nuclear and Theoretical Physics, University of Pavia, Pavia (Italy); Clerici, A.; Ferrari, C.; Zonta, C.; Zonta, A. [Department of Surgery, University of Pavia, Pavia (Italy); Nano, R. [Department of Animal Biology, University of Pavia, Pavia (Italy)

    2008-10-29

    The Boron neutron Capture Therapy research in Pavia has a long tradition: it begun more than 20 years ago at the TRIGA Mark II reactor of the University. A technique for the treatment of the hepatic metastases was developed, consisting in explanting the liver treated with {sup 10}B, irradiating it in the thermal column of the reactor, and re-implanting the organ in the patient. In the last years, the possibility of applying BNCT to the lung tumours using epithermal collimated neutron beams and without explanting the organ, is being explored. The principal obtained results of the BNCT research will be presented, with particular emphasis on the following aspects: a) the project of a new thermal column configuration to make the thermal neutron flux more uniform inside the explanted liver, b) the Monte Carlo study by means of the MCNP code of the thermal neutron flux distribution inside a patient's thorax irradiated with epithermal neutrons, and c) the measurement of the boron concentration in tissues by (n,{alpha}) spectroscopy and neutron autoradiography. (authors)

  5. Boron Neutron Capture Therapy activity of diffused tumors at TRIGA Mark II in Pavia

    International Nuclear Information System (INIS)

    Bortolussi, S.; Stella, S.; De Bari, A.; Altieri, S.; Bruschi, P.; Bakeine, J.G.; Clerici, A.; Ferrari, C.; Zonta, C.; Zonta, A.; Nano, R.

    2008-01-01

    The Boron neutron Capture Therapy research in Pavia has a long tradition: it begun more than 20 years ago at the TRIGA Mark II reactor of the University. A technique for the treatment of the hepatic metastases was developed, consisting in explanting the liver treated with 10 B, irradiating it in the thermal column of the reactor, and re-implanting the organ in the patient. In the last years, the possibility of applying BNCT to the lung tumours using epithermal collimated neutron beams and without explanting the organ, is being explored. The principal obtained results of the BNCT research will be presented, with particular emphasis on the following aspects: a) the project of a new thermal column configuration to make the thermal neutron flux more uniform inside the explanted liver, b) the Monte Carlo study by means of the MCNP code of the thermal neutron flux distribution inside a patient's thorax irradiated with epithermal neutrons, and c) the measurement of the boron concentration in tissues by (n,α) spectroscopy and neutron autoradiography. (authors)

  6. Immobilization of Ion Exchange radioactive resins of the TRIGA Mark III Nuclear Reactor

    International Nuclear Information System (INIS)

    Garcia Martinez, H.

    1999-01-01

    In the last decades many countries in the world have taken interest in the use, availability, and final disposal of dangerous wastes in the environment, within these, those dangerous wastes that contain radioactive material. That is why studies have been made on materials used as immobilization agent of radioactive waste that may guarantee its storage for long periods of time under drastic conditions of humidity, temperature change and biodegradation. In mexico, the development of different applications of radioactive material in the industry, medicine and investigation, have generated radioactive waste, sealed and open sources, whose require a special technological development for its management and final disposal. The present work has as a finality to develop the process and define the agglutinating material, bitumen, cement and polyester resin that permits immobilization of resins of Ionic Exchange contaminated by Barium 153, Cesium 137, Europium 152, Cobalt 60 and Manganese 54 generated from the nuclear reactor TRIGA Mark III. Ionic interchange contaminated resin must be immobilized and is analysed under different established tests by the Mexican Official Standard NOM-019-NUCL-1995 L ow level radioactive wastes package requirements for its near-surface final disposal. Immobilization of ionic interchange contaminated resins must count with the International Standards applicable in this process; in these standards, the following test must be taken in prototype examples: Free-standing water, leachability, compressive strength, biodegradation, radiation stability, thermal stability and burning rate. (Author)

  7. Visualization of neutron flux and power distributions in TRIGA Mark II reactor as an educational tool

    International Nuclear Information System (INIS)

    Snoj, Luka; Ravnik, Matjaz; Lengar, Igor

    2008-01-01

    Modern Monte Carlo computer codes (e.g. MCNP) for neutron transport allow calculation of detailed neutron flux and power distribution in complex geometries with resolution of ∼1 mm. Moreover they enable the calculation of individual particle tracks, scattering and absorption events. With the use of advanced software for 3D visualization (e.g. Amira, Voxler, etc.) one can create and present neutron flux and power distribution in a 'user friendly' way convenient for educational purposes. One can view axial, radial or any other spatial distribution of the neutron flux and power distribution in a nuclear reactor from various perspectives and in various modalities of presentation. By visualizing the distribution of scattering and absorption events and individual particle tracks one can visualize neutron transport parameters (mean free path, diffusion length, macroscopic cross section, up-scattering, thermalization, etc.) from elementary point of view. Most of the people remember better, if they visualize the processes. Therefore the representation of the reactor and neutron transport parameters is a convenient modern educational tool for the (nuclear power plant) operators, nuclear engineers, students and specialists involved in reactor operation and design. The visualization of neutron flux and power distributions in Jozef Stefan Institute TRIGA Mark II research reactor is treated in the paper. The distributions are calculated with MCNP computer code and presented using Amira and Voxler software. The results in the form of figures are presented in the paper together with comments qualitatively explaining the figures. (authors)

  8. Utilization of a typical 250 kW TRIGA Mark II reactor at a University

    International Nuclear Information System (INIS)

    Villa, M.; Boeck, H.; Musilek, A.

    2007-01-01

    The 250 kW TRIGA Mark-II reactor operates since March 1962 at the Atominstitut Vienna/Austria. Its main tasks are nuclear education and training in the fields of neutron- and solid state physics, nuclear technology, reactor safety, radiochemistry, radiation protection and dosimetry, and low temperature physics and fusion research. Academic research is carried out by students in the above mentioned fields coordinated and supervised by about 70 staff members with the aim of a masters- or PhD degree in one of the above mentioned areas. During the past 15 years about 580 students graduated through the Atominstitut. In addition, the Atominstitut co-operates closely with the nearby located IAEA in research projects, coordinated research programs (CRP) and supplying expert services. Regular training courses are carried out for the IAEA for Safeguard Trainees, fellowship places are offered for scientists from developing countries and staff members carry out expert missions to research centres in Africa, Asia and South America. Special Nuclear Material (SNM) is stored for calibration purposes at the Atominstitut belonging to the IAEA. (author)

  9. The future of the IPR-R1 TRIGA MARK I reactor after 48 years operation

    International Nuclear Information System (INIS)

    Maretti, Fausto Junior; Sette Camara, Luiz Otavio I.; Oliveira, Paulo Fernando

    2008-01-01

    The TRIGA Mark I IPR-R1 Reactor operates in the Nuclear Technology Development Center/ Brazilian Committion for Nuclear Energy (CDTN/CNEN), originally Institute of Radioactive Researches, in Belo Horizonte, Minas Gerais, since November 6, 1960. Initially it operated for isotope production for different uses, being later used in wide scale for another purposes as analyses for activation with neutrons and training of nuclear power plants operators. Dozens of degree theses were also developed with the use of the reactor. Along the years, several improvements were introduced in the reactor and its auxiliary systems, with the purpose to provide better use of the facilities and with the objective to increase the safety in the operation. The reactor is ready right now to operate at 250 kW, and for sure the nuclear applications programmed will be improved. The Operation Manual and the Safety Analysis report were already modified, as well as the Emergency Plan and the relative procedures to the same. After the tests at the end of 2008, the reactor will already be operating in the new power. This work presents a description of the several accomplishments of the last years and comments about the possibility of new uses for the reactor in the several areas of nuclear applications and some of the experiments and tests results during the upgrading program. (authors)

  10. Activation calculation of steel of the control rods of TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Garcia M, T.; Cruz G, H. S.; Ruiz C, M. A.; Angeles C, A.

    2014-10-01

    In the pool of TRIGA Mark III reactor of the Instituto Nacional de Investigaciones Nucleares (ININ), there are control rods that were removed from the core, and which are currently on shelves of decay. These rods were part of the reactor core when only had fuel standard (from 1968-1989). To conduct a proper activation analysis of the rods, is very important to have well-characterized the materials which are built, elemental composition of the same ones, the atomic densities and weight fractions of the elements that constitute them. To determine the neutron activation of the control rods MCNP5 code was used, this code allows us to have well characterized the radionuclides inventory that were formed during irradiation of the control rods. This work is limited to determining the activation of the steel that is part of the shielding of the control rods, the nuclear fuel that is in the fuel follower does not include. The calculation model of the code will be validated with experimental measurements and calculating the activity of fission products of the fuel follower which will take place at the end of 2014. (Author)

  11. Neutron spectra in two beam ports of the TRIGA Mark III reactor

    Energy Technology Data Exchange (ETDEWEB)

    Vega C, H. R.; Hernandez D, V. M. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98060 Zacatecas (Mexico); Aguilar, F.; Paredes, L. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Rivera M, T., E-mail: fermineutron@yahoo.com [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Unidad Legaria, Av. Legaria 694, 11500 Mexico D. F. (Mexico)

    2013-10-15

    The neutron spectra have been measured in two beam ports, radial and tangential, of the TRIGA Mark III nuclear reactor from the National Institute of Nuclear Research. Measurements were carried out with the core with mixed fuel (Leu 8.5/20 and Flip Heu 8.5/70). Two reactor powers, 5 and 10 W, were used during neutron spectra measurements using a Bonner sphere spectrometer with a {sup 6}Lil(Eu) scintillator and 2, 3, 5, 8, 10 and 12 inches-diameter high density polyethylene spheres. The neutron spectra were unfolded using the NSDUAZ unfolding code; from each spectrum the total neutron flux, the neutron mean energy and the neutron ambient dose equivalent dose were determined. Measured spectra show fission (E≥ 0.1 MeV), epithermal (from 0.4 eV up to 0.1 MeV) and thermal neutrons (E≤ 0.4 eV). For both reactor powers the spectra in the radial beam port have similar features which are different to the neutron spectrum characteristics in the tangential beam port. (Author)

  12. Behavior of exposed human lymphocytes to a neutron beam of the Reactor TRIGA Mark III

    International Nuclear Information System (INIS)

    Carbajal R, M. I.; Arceo M, C.; Aguilar H, F.; Guerrero C, C.

    2012-10-01

    The living beings are permanently exposed to radiations of natural origin: cosmic and geologic, as well as the artificial radiations that come from sources elaborated by the man. The artificial sources have an important use in the medical area. Particularly has been increased the neutrons use due to the effectiveness that they have to damage the cells with regard to other radiation types. The biological indicator of exposition to ionizing radiation more reliable is the chromosomal aberrations study, specifically the dicentrics in human lymphocytes. This test allows, establishing the exposition dose in function of the damage quantity. The dicentrics have a behavior in function of the dose. The calibration curve that describes this behavior is specific for each type of ionizing radiation. In the year 2006 beginning was given to the expositions of human lymphocytes to a neutron beam generated in the reactor TRIGA Mark III of the Instituto Nacional de Investigaciones Nucleares (ININ) in Mexico. Up to 2008 the response dose curve comprised an interval of exposition time of up to 30 minutes. Moreover, the interval between 10 an 20 minutes is included, since was observed that this last is indispensable for the adjustment waited in a lineal model. (Author)

  13. Operational Experience with the TRIGA Mark II Reactor of the University of Pavia

    Energy Technology Data Exchange (ETDEWEB)

    Tigliole, A. Borio Di; Alloni, D.; Cagnazzo, M.; Coniglio, M.; Lana, F.; Losi, A.; Magrotti, G.; Manera, S.; Marchetti, F.; Pappalardo, P.; Prata, M.; Provasi, M.C.; Salvini, A.; Scian, G.; Vinciguerra, G. [University of Pavia, Laboratory of Applied Nuclear Energy (L.E.N.A), Via Aselli 41, 27100 Pavia (Italy)

    2011-07-01

    The Laboratory of Applied Nuclear Energy (LENA) is an Interdepartmental Research Centre of the University of Pavia which operates a 250 kW TRIGA Mark II Research Nuclear Reactor, a Cyclotron for the production of radioisotopes and other irradiation facilities. The reactor is in operation since 1965 and many home-made upgrading were realized in the past years in order to assure a continuous operation of the reactor for the future. The annual reactor operational time at nominal power is in the range of 300 - 400 hours depending upon the time schedule of some experiments and research activities. The reactor is mainly used for NAA activities, BNCT research, samples irradiation and training. In specific, few tens of hours of reactor operation per year are dedicated to training courses for University students and for professionals. Besides, the LENA Centre hosts every year more than one thousand high school students in visit. Lately, LENA was certified ISO 9001:2008 for the ''operation and maintenance of the reactor'' and for the ''design and delivery of the irradiation service''. Nowadays the reactor shows a good technical state and, at the moment, there are no political or economical reason to consider the reactor shut-down. (author)

  14. Comparison of standardised decommissioning costing tools on pilot Vienna TRIGA MARK-II research reactor

    International Nuclear Information System (INIS)

    Hornacek, M.; Kristofova, K.; Slugen, V.; Zachar, M.; Stummer, T.

    2017-01-01

    The main purpose of the paper is to compare decommissioning costing code CERREX (Cost Estimation for Research Reactors in Excel) with advanced calculation methodology applied in eOMEGA-RR code. CERREX code was developed in line with the IAEA recommendations for decommissioning costing of research facilities and fully implements the ISDC (International Structure for Decommissioning Costing of Nuclear Installations) structure and costing methodology. In comparison with CERREX, usually applied in preliminary costing, the code eOMEGA-RR incorporates the realistic activity and material flow during decommissioning process (e.g. decontamination, dismantling and waste management). This advanced approach enables to carry out the decommissioning planning and costing more effectively. Moreover, the user-friendly interface helps to perform wide range of sensitivity analyses. In order to meet the above mentioned objectives, the model calculation costing case for TRIGA MARK-II research reactor in Vienna was developed in both calculation codes. The whole process covered four step-by-step procedures to be implemented. At first, inventory database taking into account physical as well as radiological parameters (e.g.: contamination, dose rates, nuclide vectors, limits and conditions) was developed. At second, advanced decommissioning costing case using CERREX and eOMEGA-RR code was created. At third, sensitivity analyses to estimate the impact of changing input parameters on calculated results were performed. Finally, costing results obtained from both cost calculation codes are compared and discussed. (authors)

  15. Reactor physics tests of TRIGA Mark-II Reactor in Ljubljana

    International Nuclear Information System (INIS)

    Ravnik, M.; Mele, I.; Trkov, A.; Rant, J.; Glumac, B.; Dimic, V.

    2008-01-01

    TRIGA Mark-II Reactor in Ljubljana was recently reconstructed. The reconstruction consisted mainly of replacing the grid plates, the control rod mechanisms and the control unit. The standard type control rods were replaced by the fuelled follower type, the central grid location (A ring) was adapted for fuel element insertion, the triangular cutouts were introduced in the upper plate design. However, the main novelty in reactor physics and operational features of the reactor was the installation of a pulse rod. Having no previous operational experience in pulsing, a detailed and systematic sequence of tests was defined in order to check the predicted design parameters of the reactor with measurements. The following experiments are treated in this paper: initial criticality, excess reactivity measurements, control rod worth measurement, fuel temperature distribution, fuel temperature reactivity coefficient, pulse parameters measurement (peak power, prompt energy, peak temperature). Flux distributions in steady state and pulse mode were measured as well, however, they are treated only briefly due to the volume of the results. The experiments were performed with completely fresh fuel of 12 w% enriched Standard Stainless Steel type. The core configuration was uniform (one fuel element type, including fuelled followers) and compact (no irradiation channels or gaps), as such being particularly convenient for testing the computer codes for TRIGA reactor calculations. Comparison of analytical predictions, obtained with WIMS, SLXTUS, TRIGAP and PULSTRI codes to measured values showed agreement within the error of the measurement and calculation. The paper has the following contents: 1. Introduction; 2. Steady State Experiments; 2.1. Core loading and critical experiment; 2.2. Flux range determination for tests at zero power; 2.3. Digital reactivity meter checkout; 2.4. Control rod worth measurements; 2.5. Excess reactivity measurement; 2.6. Thermal power calibration; 2

  16. Measurement of argon concentrations in a TRIGA Mark-III pool

    Energy Technology Data Exchange (ETDEWEB)

    Simms, R [California State University, Northridge, CA (United States)

    1974-07-01

    Argon-41, the principal radioactive effluent from a pool type reactor during normal operation, is produced by the {sup 40}A (n,{gamma}) reaction. The reactant, {sup 40}A, is introduced into the pool water by contact with the air. Reduction in radioactive argon release can be accomplished by reducing the concentration of dissolved {sup 40}A and retaining the {sup 41}A within the pool. However, little data were available concerning the mechanisms of argon introduction, production, retention, and release from a reactor pool. Experiments have therefore been performed at the Torrey Pines TRIGA Mark-III Reactor to develop techniques to sample dissolved argon and to provide data on argon concentrations in the pool for release modeling studies. Significant results for argon dissolved at different pool depths can only be obtained if the water samples are sealed at the point of collection. A special handling tool was developed to perform this remote operation. Pool samples were counted for {sup 41}A soon after collection with a NaI spectrometer. After allowing one day for decay of {sup 41}A, the concentration of {sup 40}A in the water sample was determined by neutron activation analysis. In each case, the 1.29 MeV gamma-ray peak of {sup 41}A was used. Interference from the 1.37 MeV {sup 24}Na peak was considered and its effect subtracted after determining {sup 24}Na content from the 2.75 MeV {sup 24}Na peak and a sodium standard. A Ge(Li) detector was tried and found to eliminate the problem, but it introduced an unacceptable geometrical effect dependent on bubble size within the sample bottles. Samples were taken from the 27 ft deep TRIGA pool at various locations. Results were obtained for samples taken on several different days along the same vertical line about 3-1/2 ft from the reactor centerline. Temperature measurements along this vertical traverse indicated a sharp temperature gradient at about 15 ft below the surface ({approx}6 ft above the top of the reactor). The

  17. Safety analysis and optimization of the core fuel reloading for the Moroccan TRIGA Mark-II reactor

    International Nuclear Information System (INIS)

    Nacir, B.; Boulaich, Y.; Chakir, E.; El Bardouni, T.; El Bakkari, B.; El Younoussi, C.

    2014-01-01

    Highlights: • Additional fresh fuel elements must be added to the reactor core. • TRIGA reactor could safely operate around 2 MW power with 12% fuel elements. • Thermal–hydraulic parameters were calculated and the safety margins are respected. • The 12% fuel elements will have no influence on the safety of the reactor. - Abstract: The Moroccan TRIGA MARK II reactor core is loaded with 8.5% in weight of uranium standard fuel elements. Additional fresh fuel elements must periodically be added to the core in order to remedy the observed low power and to return to the initial reactivity excess at the End Of Cycle. 12%-uranium fuel elements are available to relatively improve the short fuel lifetime associated with standard TRIGA elements. These elements have the same dimensions as standards elements, but with different uranium weight. The objective in this study is to demonstrate that the Moroccan TRIGA reactor could safely operate, around 2 MW power, with new configurations containing these 12% fuel elements. For this purpose, different safety related thermal–hydraulic parameters have been calculated in order to ensure that the safety margins are largely respected. Therefore, the PARET model for this TRIGA reactor that was previously developed and combined with the MCNP transport code in order to calculate the 3-D temperature distribution in the core and all the most important parameters like the axial distribution of DNBR (Departure from Nucleate Boiling Ratio) across the hottest channel. The most important conclusion is that the 12% fuel elements utilization will have no influence on the safety of the reactor while working around 2 MW power especially for configurations based on insertions in C and D-rings

  18. Computational analysis of neutronic parameters for TRIGA Mark-II research reactor using evaluated nuclear data libraries

    International Nuclear Information System (INIS)

    Uddin, M.N.; Sarker, M.M.; Khan, M.J.H.; Islam, S.M.A.

    2010-01-01

    The aim of this study is to analyze the neutronic parameters of TRIGA Mark-II research reactor using the chain of NJOY-WIMS-CITATION computer codes based on evaluated nuclear data libraries CENDL-2.2 and JEFF-3.1.1. The nuclear data processing code NJOY99.0 has been employed to generate the 69 group WIMS library for the isotopes of TRIGA core. The cell code WIMSD-5B was used to generate the cross sections in CITATION format and then 3-dimensional diffusion code CITTATION was used to calculate the neutronic parameters of the TRIGA Mark-II research reactor. All the analyses were performed using the 7-group macroscopic cross section library. The CITATION test-runs using different cross section sets based on different models applied in WIMS calculations have shown a strong influence of those models on the final integral parameters. Some of the cells were specially treated with PRIZE options available in WIMSD-5B to take into account the fine structure of the flux gradient in the fuel-reflector interface region. It was observed that two basic parameters, the effective multiplication factor, k eff and the thermal neutron flux, were in good agreement among the calculated results with each other as well as the measured values. The maximum power densities at the hot spot were 1.0446E02 W/cc and 1.0426E02 W/cc for the libraries CENDL-2.2 and JEFF-3.1.1 respectively. The calculated total peaking factors 5.793 and 5.745 were compared to the original SAR value of 5.6325 as well as MCNP result. Consequently, this analysis will be helpful to enhance the neutronic calculations and also be used for the further thermal-hydraulics study of the TRIGA core.

  19. Licensing of the TRIGA Mark III reactor at the Mexican Nuclear Centre

    International Nuclear Information System (INIS)

    Ramirez, R.M.; Arrendondo, R.R.

    1990-01-01

    The TRIGA Mark III reactor at the Mexican Nuclear Centre went critical in 1968 and remained so until 1979 when the National Commission for Nuclear Safety and Safeguards (CNSNS), the Mexican regulatory authority, was set up. The reactor was therefore operating without a formal operating license, and the CNSNS accordingly requested the ININ to license the reactor under the existing conditions and to ensure that any modification of the original design complied with Standards ANSI/ANS-15 and with the code of practice set out in IAEA Safety Series No. 35. The most relevant points in granting the operating licence were: (a) the preparation of the Safety Report; (b) the formulation and application of the Quality Assurance Programme; (c) the reconditioning of the following reactor systems: the cooling systems; the ventilation and exhaust system; the monitoring system and control panel; (d) the training of the reactor operating staff at junior and senior levels; and (e) the formulation of procedures and instructions. Once the provisional operating license was obtained for the reactor it was considered necessary to modify the reactor core, which has been composed of 20% enriched standards fuel, to a mixed core based on a mixture of standard fuel and FLIP-type fuel with 70% 235 U enrichment. The CNSNS therefore requested that the mixed core be licensed and a technical report was accordingly annexed to the Safety Report, its contents including the following subjects: (a) neutron analysis of the proposed configuration; (b) reactor shutdown margins; (c) accident analysis; and (d) technical specifications. The licensing process was completed this year and we are now hoping to obtain the final operating license

  20. Elaboration of the configuration and programming of the interlocks system of the TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Mejia C, M. A.

    2016-01-01

    The modernization of the TRIGA Mark III reactor interlock system requires a system that provides high reliability, flexibility and ease of operation during reactor operation. With this modernization of the system, is intended to prevent, control and mitigate the causes of probable accidents reported in the reactor accident analysis. On the other hand, is foreseen the ease reactor operation in a simple, safe and efficient way. The programmable logic controller can be programmed by programming instructions using simple language and easy to develop, these can be modified from a computer using the programming software. In addition, another of the advantages offered by the controller is that can be modified from a touch screen (human-machine interface) that allows adjustment, without the need to use programming software and diagnostic functions during the process. As a result of the present work, a situation of improvement in the reactor operation was generated, facilitating the handling of the bridge and increasing the efficiency of the system in the execution of the operating conditions of the installations external to the reactor. A modern, more reliable and much less expensive system was achieved than the previous one, avoiding that the maintenance to the system generates high expenses. With respect to the development of the application programming, a control was implemented that allows to select a zone of the five that have inside the pool to carry out the displacement of automatic way and later to be located in that zone, having in this way a greater efficiency and ease in bridge control. (Author)

  1. Modernization of the facilities of the TRIGA Mark III reactor of ININ

    International Nuclear Information System (INIS)

    Mendez T, D.; Flores C, J.

    2016-09-01

    The TRIGA Mark III reactor of the Instituto Nacional de Investigaciones Nucleares (ININ) has been in operation since 1968 under strict maintenance and component replacement programs, which has allowed its safe operation during this time. Under this scheme, the reactor was operating under suitable conditions, taking into account the different requests for operation that were received for the samples irradiation for the radioisotopes production such as the Sm-153, personnel training, basic research, archaeology and environmental studies and nuclear chemistry of the elements. However, a modernization program of its components and laboratories was required, in order to improve safety in the operation of the same and to increase its use in the analysis of samples by neutron activation and in the training of personnel. This program known as Modernization Program of the Reactor Facilities, was proposed alongside the project to replace high-enrichment fuels with low-enrichment fuels at the end of 2011 and early 2012. The central aspects of this program are described in this work, grouped into generic topics that include instrumentation and control, the radiological monitoring system of the area, the cooling system, the ventilation system, the neutron activation analysis laboratory, the manufacture of graphite elements, inspection submersible system of the pool, temporary storage system for irradiated fuels, traveling crane, Reactor support laboratories and technical meetings, courses and seminars for reactor personnel and associated groups. It also describes some of the most relevant components required for each system and the progress that is made in each one of them. As a fundamental result of the implementation of this Modernization Program of the Reactor Facilities, there has been a substantial improvement in the performance of the systems and components of its facilities, in the reliability of its operation and in the safety of the same. (Author)

  2. Adaptive fuzzy control of neutron power of the TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Rojas R, E.

    2014-01-01

    The design and implementation of an identification and control scheme of the TRIGA Mark III research nuclear reactor of the Instituto Nacional de Investigaciones Nucleares (ININ) of Mexico is presented in this thesis work. The identification of the reactor dynamics is carried out using fuzzy logic based systems, in which a learning process permits the adjustment of the membership function parameters by means of techniques based on neural networks and bio-inspired algorithms. The resulting identification system is a useful tool that allows the emulation of the reactor power behavior when different types of insertions of reactivity are applied into the core. The identification of the power can also be used for the tuning of the parameters of a control system. On the other hand, the regulation of the reactor power is carried out by means of an adaptive and stable fuzzy control scheme. The control law is derived using the input-output linearization technique, which permits the introduction of a desired power profile for the plant to follow asymptotically. This characteristic is suitable for managing the ascent of power from an initial level n o up to a predetermined final level n f . During the increase of power, a constraint related to the rate of change in power is considered by the control scheme, thus minimizing the occurrence of a safety reactor shutdown due to a low reactor period value. Furthermore, the theory of stability in the sense of Lyapunov is used to obtain a supervisory control law which maintains the power error within a tolerance region, thus guaranteeing the stability of the power of the closed loop system. (Author)

  3. Analysis of gamma heating at TRIGA mark reactor core Bandung using plate type fuel

    International Nuclear Information System (INIS)

    Setiyanto; Tukiran Surbakti

    2016-01-01

    In accordance with the discontinuation of TRIGA fuel element production by its producer, the operation of all TRIGA type reactor of at all over the word will be disturbed, as well as TRIGA reactor in Bandung. In order to support the continuous operation of Bandung TRIGA reactor, a study on utilization of fuel plate mode, as used at RSG-GAS reactor, to replace the cylindrical model has been done. Various assessments have been done, including core design calculation and its safety aspects. Based on the neutronic calculation, utilization of fuel plate shows that Bandung TRIGA reactor can be operated by 20 fuel elements only. Compared with the original core, the new reactor core configuration is smaller and it results in some empty space that can be used for in-core irradiation facilities. Due to the existing of in-core irradiation facilities, the gamma heating value became a new factor that should be evaluated for safety analysis. For this reason, the gamma heating for TRIGA Bandung reactor using fuel plate was calculated by Gamset computer code. The calculations based on linear attenuation equations, line sources and gamma propagation on space. Calculations were also done for reflector positions (Lazy Susan irradiation facilities) and central irradiation position (CIP), especially for any material samples. The calculation results show that gamma heating for CIP is significantly important (0.87 W/g), but very low value for Lazy Susan position (lest then 0.11 W/g). Based on this results, it can be concluded that the utilization of CIP as irradiation facilities need to consider of gamma heating as data for safety analysis report. (author)

  4. Neuro-diffuse algorithm for neutronic power identification of TRIGA Mark III reactor; Algoritmo neuro-difuso para la identificacion de la potencia neutronica del reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Rojas R, E.; Benitez R, J. S. [Instituto Tecnologico de Toluca, Division de Estudios de Posgrado e Investigacion, Av. Tecnologico s/n, Ex-Rancho La Virgen, 50140 Metepec, Estado de Mexico (Mexico); Segovia de los Rios, J. A.; Rivero G, T. [ININ, Gerencia de Ciencias Aplicadas, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)], e-mail: jorge.benitez@inin.gob.mx

    2009-10-15

    In this work are presented the results of design and implementation of an algorithm based on diffuse logic systems and neural networks like method of neutronic power identification of TRIGA Mark III reactor. This algorithm uses the punctual kinetics equation as data generator of training, a cost function and a learning stage based on the descending gradient algorithm allow to optimize the parameters of membership functions of a diffuse system. Also, a series of criteria like part of the initial conditions of training algorithm are established. These criteria according to the carried out simulations show a quick convergence of neutronic power estimated from the first iterations. (Author)

  5. Capture programs, analysis, data graphication for the study of the thermometry of the TRIGA Mark III reactor core; Programas de captura, analisis y graficado de datos para el estudio de la termometria del nucleo del reactor TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Paredes G, L.C

    1991-05-15

    This document covers the explanation of the capture programs, analysis and graphs of the data obtained during the measurement of the temperatures of the instrumented fuel element of the TRIGA Mark III reactor and of the coolant one near to this fuel, using the conversion card from Analogic to Digital of 'Data Translation', and using a signal conditioner for five temperature measurers with the help of thermo par type K, developed by the Simulation and Control of the nuclear systems management department, which gives a signal from 0 to 10 Vcd for an interval of temperature of 0 to 1000 C. (Author)

  6. Mechanism design for the control rods conduction of TRIGA Mark III reactor in the NINR; Diseno del mecanismo para la conduccion de las barras de control del reactor Triga Mark III del ININ.

    Energy Technology Data Exchange (ETDEWEB)

    Franco C, A

    1997-12-01

    This work presents in the first chapter a general studio about the reactor and the importance of control rods in the reactor , the mechaniucal design attending to requisitions that are imposed for conditions of operation of the reactor are present in the second chapter, the narrow relation that exists with the new control console and the mechanism is developed in the thired chapter, this relation from a point of view of an assembly of components is presents in fourth chapter, finally reaches and perspectives of mechanism forming part of project of the automation of reactor TRIGA MARK III, are present in the fifth chapter. (Author).

  7. ANALYSIS OF GAMMA HEATING AT TRIGA MARK REACTOR CORE BANDUNG USING PLATE TYPE FUEL

    Directory of Open Access Journals (Sweden)

    Setiyanto Setiyanto

    2016-10-01

    Full Text Available ABSTRACT In accordance with the discontinuation of TRIGA fuel element production by its producer, the operation of all TRIGA type reactor of at all over the word will be disturbed, as well as TRIGA reactor in Bandung. In order to support the continuous operation of Bandung TRIGA reactor, a study on utilization of fuel plate mode, as used at RSG-GAS reactor, to replace the cylindrical model has been done. Various assessments have been done, including core design calculation and its safety aspects. Based on the neutronic calculation, utilization of fuel plate shows that Bandung TRIGA reactor can be operated by 20 fuel elements only. Compared with the original core, the new reactor core configuration is smaller and it results in some empty space that can be used for in-core irradiation facilities. Due to the existing of in-core irradiation facilities, the gamma heating value became a new factor that should be evaluated for safety analysis. For this reason, the gamma heating for TRIGA Bandung reactor using fuel plate was calculated by Gamset computer code. The calculations based on linear attenuation equations, line sources and gamma propagation on space. Calculations were also done for reflector positions (Lazy Susan irradiation facilities and central irradiation position (CIP, especially for any material samples. The calculation results show that gamma heating for CIP is significantly important (0,87 W/g, but very low value for Lazy Susan position (lest then 0,11 W/g. Based on this results, it can be concluded that the utilization of CIP as irradiation facilities need to consider of gamma heating as data for safety analysis report. Keywords: gamma heating, nuclear reactor, research reactor, reactor safety.   ABSTRAK Dengan dihentikannya produksi elemen bakar reaktor jenis Triga oleh produsen, maka semua reaktor TRIGA di dunia terganggu operasinya, termasuk juga reaktor TRIGA 2000 di Bandung. Untuk mendukung pengoperasian reaktor TRIGA Bandung

  8. Neutron optics experiments at the TRIGA Mark II reactor of the Atominstitut Wien

    International Nuclear Information System (INIS)

    Jericha, E.; Badurek, G.; Baron, M.; Hasegawa, Y.; Jaekel, M.; Klepp, J.; Rofner, A.; Sponar, S.; Trinker, M.; Villa, M.; Rauch, H.

    2004-01-01

    We present the layout and characteristics of the 3 neutron optics instruments located at the beam ports of the Vienna TRIGA reactor (hosted by the Atominstitut of the Austrian Universities, Vienna University of Technology) and the most recent experiments performed thereon. (author)

  9. In-service inspection and maintenance schedule for a typical TRIGA Mark-II reactor

    International Nuclear Information System (INIS)

    Boeck, H.

    1996-05-01

    This report lists all the systems and components of the TRIGA reactor Vienna which are inspected and maintained in regular intervals. These intervals are categorized in monthly, quarterly, semi-annual and annual inspections. Further the type of inspection and the responsibility for the inspection is shown. For each component specific inspection sheets have been developed, some examples are given in the annex. (author)

  10. Evaluation for the status of the IAEA inspection at Hanaro and TRIGA Mark II and III reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyun Sook; Lee, Byung Doo

    2007-11-15

    Safeguards implementation of nuclear material was carried out at facility level in an effect to support the peaceful nuclear activities in KAERI. Safeguards implementation is to fulfill the obligations associated with international agreements such as IAEA comprehensive safeguards agreement and additional protocol. IAEA inspection is the most important and basic factor of the safeguards implementation for the purpose of verifying whether all source or special fissionable material is diverted to nuclear weapons or other nuclear explosive devices. The status of the IAEA inspection at Hanaro and TRIGA Mark II and III reactor during 2001-2006 is evaluated in this report.

  11. Irradiation positions for fission-track dating in the University of Pavia TRIGA Mark II nuclear reactor

    International Nuclear Information System (INIS)

    Oddone, Massimo; Meloni, Sandro; Balestrieri, Maria Laura; Bigazzi, Giulio

    2002-01-01

    An irradiation position arranged is described in the present paper for fission-track dating in the Triga Mark II reactor of the University of Pavia. Fluence values determined using the NIST glass standard SRM 962a for fission-track dating and the traditional metal foils are compared. Relatively good neutron thermalization (φ th /φ f = 0.956) and lack of significant fluence spatial gradients are good factors for fission-track dating. Finally, international age standards (or putative age standards) irradiated in this new position yielded results consistent with independent reference ages. (author)

  12. Epithermal neutron flux characterization of the TRIGA Mark III reactor, Salazar, Mexico, for use in Internal Neutron Activation Analysis

    International Nuclear Information System (INIS)

    Diaz Rizo, O.; Herrera Peraza, E.

    1996-01-01

    The non ideality of the epithermal neutron flux distribution at a reactor site parameter (made, using Chloramine-T method. Radiochemical purity and stability of the labelled product were determined by radiochromatography. The labelled Melagenine-II showed two radioactive fractions thermal-to-epithermal neutron ratio (f) were determined in the 3 typical irradiations positions of the TRIGA Mark III reactor of the National Nuclear Research Institute, Salazar, Mexico, using the Cd-ratio for multi monitor and bare bi-isotopic monitor methods respectively. This characterization is of use in the K o - method of neutron activation analysis, recently introduced at the Institute

  13. Evaluation for the status of the IAEA inspection at Hanaro and TRIGA Mark II and III reactor

    International Nuclear Information System (INIS)

    Kim, Hyun Sook; Lee, Byung Doo

    2007-11-01

    Safeguards implementation of nuclear material was carried out at facility level in an effect to support the peaceful nuclear activities in KAERI. Safeguards implementation is to fulfill the obligations associated with international agreements such as IAEA comprehensive safeguards agreement and additional protocol. IAEA inspection is the most important and basic factor of the safeguards implementation for the purpose of verifying whether all source or special fissionable material is diverted to nuclear weapons or other nuclear explosive devices. The status of the IAEA inspection at Hanaro and TRIGA Mark II and III reactor during 2001-2006 is evaluated in this report

  14. Capture programs, analysis, data graphication for the study of the thermometry of the TRIGA Mark III reactor core

    International Nuclear Information System (INIS)

    Paredes G, L.C.

    1991-05-01

    This document covers the explanation of the capture programs, analysis and graphs of the data obtained during the measurement of the temperatures of the instrumented fuel element of the TRIGA Mark III reactor and of the coolant one near to this fuel, using the conversion card from Analogic to Digital of 'Data Translation', and using a signal conditioner for five temperature measurers with the help of thermo par type K, developed by the Simulation and Control of the nuclear systems management department, which gives a signal from 0 to 10 Vcd for an interval of temperature of 0 to 1000 C. (Author)

  15. Operation experience with the 3 MW TRIGA Mark-II research reactor of Bangladesh

    International Nuclear Information System (INIS)

    Islam, M.S.; Haque, M.M.; Salam, M.A.; Rahman, M.M.; Khandokar, M.R.I.; Sardar, M.A.; Saha, P.K.; Haque, A.; Malek Sonar, M.A.; Uddin, M.M.; Hossain, S.M.S.; Zulquarnain, M.A.

    2004-01-01

    The 3 MW TRIGA Mark-II research reactor of Bangladesh Atomic Energy Commission (BAEC) has been operating since September 14, 1986. The reactor is used for radioisotope production ( 131 I, 99m Tc, 46 Sc), various R and D activities and manpower training. The reactor has been operated successfully since it's commissioning with the exception of a few reportable incidents. Of these, the decay tank leakage incident of 1997 is considered to be the most significant one. As a result of this incident, reactor operation at full power under forced-convection mode remained suspended for about 4 years. During that time, the reactor was operated at a power level of 250 kW so as to carry out experiments that require lower neutron flux. This was made possible by establishing a temporary by pass connection across the decay tank using local technology. The other incident was the contamination of the Dry Central Thimble (DCT) that took place in March 2002 when a pyrex vial containing 50 g of TeO 2 powder got melted inside the DCT. The vial was melted due to high heat generation on its surface while the reactor was operated for 8 hours at 3 MW for trial production of Iodine-131 ( 131 I). A Wet Central Thimble (WCT) was used to replace the damaged DCT in June 2002 such that the reactor operation could be resumed. The WCT was again replaced by a new DCT in June 2003 such that radioisotope production could be continued. A total of 873 irradiation requests (IRs) have been catered for different reactor uses. Out of these, 114 IRs were for radioisotope (RI) production and 759 IRs for different experiments. The total amount of RI produced stands at about 2100 GBq. The total amount of burn-up-fuel is about 6158 MWh. Efforts are on to undertake an ADP project so as to convert the analog console and I and C system of the reactor into digital one. The paper summarizes the reactor operation experiences focusing on troubleshooting, rectification, modification, RI production, various R and D

  16. Behavior of exposed human lymphocytes to a neutron beam of the reactor TRIGA Mark III

    International Nuclear Information System (INIS)

    Carbajal R, M. I.

    2012-01-01

    Excessive exposure to ionizing radiation occurs in people who require radiation treatment, also in those for work can come to receive doses above the permitted levels. A third possibility of exposure is the release of radioactive material in which the general population is affected. Most of the time the exhibition is partial and only rarely occurs throughout the body. For various reasons, situations arise where it is impossible to determine by conventional physical methods, the amount of radiation you were exposed to the affected person and in these cases where the option to follow is the Biological Dosimetry, where the analysis of chromosomes dicentrics is used to estimate the dose of ionizing radiation exposure. A calibration curve is generated from in vitro analysis of dicentric chromosome, which are found in human lymphocytes, treated with different types and doses of radiation. The dicentric is formed from two lesions, one on each chromosome and their union results in a structure having two centromeres, acentric fragment with her for the union of several chromosomes leads to more complex structures as tri-centric s, tetra or penta-centric s, which have the same origin. The dose-response curve is estimated by observing the frequency of dicentrics and extrapolated to a dose-effect curve previously established, for which it is necessary that each lab has its own calibration curves, taking into account that for a Let low radiation, dose-effect curve follows a linear-quadratic model Y=C + αD + βD. The production of dicentric chromosomes with a high Let, was studied using a beam of neutrons generated in the reactor TRIGA Mark III with an average energy of 1 MeV, adjusting the linear model Y=αD. The dose-response relationship is established in blood samples from the same donor, the coefficient α of the dose-response is Y = (0.3692 ± 0.011 * D), also shows that saturation is reached in system 4 Gy. (Author)

  17. Operation experience and maintenance at the TRIGA Mark II L.E.N.A. reactor

    International Nuclear Information System (INIS)

    Gngoli, F.; Berzero, A.; Lana, F.; Rosti, G.; Meloni, S.

    2008-01-01

    The TRIGA Mark II reactor of the University of Pavia was operated in the last two years on a routine basis, mostly for neutron activation analysis purposes. Moreover the reactor was completely shutdown in the first six months of this year to allow the dismantling of the NADIR experimental setup. The paper presents: - Reactor operation from July 1990 to June 1992; - Reactor users in the time period January 1990 - December 1991; - Specific activities of some radionuclides in the filling materials; - Specific activity of some radionuclides in thermal column materials. Operations related to dismantling of NADIR experimental facility are described. Finally the new thermal column configuration is presented. Starting from the end inside the reactor tank, a graphite layer (35 cm thick) was positioned, followed by a bismuth layer (10 cm thick) to reduce gamma-ray intensity. The old graphite rods were then positioned leaving in the central part, on the equatorial plane of the thermal column, a cavity whose vertical section has 40 cm width and 20 cm height. The bottom of the cavity, towards to the reactor tank, has been lined with additional layers of graphite (10 cm), bismuth (10 cm) and again graphite (1 cm). The new configuration allowed new experiments to be performed. The cavity in the central part has been created to allow the irradiation of large biological samples such as experimental animal and human livers. This is a peculiar step in a neutron capture boron therapy project to be carried out at the University of Pavia. In order to avoid an implemented 41 Ar production in the void space between shutters and the thermal column outer end, the external surface of the thermal column has been coated with boral sheets. The neutron flux profile, both thermal and epithermal, and cadmium ratio for gold are shown. The flux distribution appears to be adequate to proceed with the neutron capture boron therapy experiment. The LENA Health Physics Service has checked all phases of

  18. The new area monitoring system and the fuel database of the TRIGA Mark II reactor in Vienna

    International Nuclear Information System (INIS)

    Villa, M.; Boeck, H.; Hofbauer, M.; Schwarz, V.

    2004-01-01

    The 250 kW TRIGA Mark-II reactor operates since March 1962 at the Atominstitut, Vienna, Austria. Its main tasks are nuclear education and training in the fields of neutron- and solid state physics, nuclear technology, reactor safety, radiochemistry, radiation protection and dosimetry, and low temperature physics and fusion research. Academic research is carried out by students in the above mentioned fields coordinated and supervised by about 70 staff members with the aim of a masters- or PhD degree in one of the above mentioned areas. After 25 years of successful operation, it was necessary to exchange the old area monitoring system with a new digital one. The purpose of the new system is the permanent control of the reactor hall, the primary and secondary cooling system and the monitoring of the ventilation system. The paper describes the development and implementation of the new area monitoring system. The second topic in this paper describes the development of the new fuel database. Since March 7th, 1962, the TRIGA Mark II reactor Vienna operates with an average of 263 MWh per year, which corresponds to a uranium burn-up of 13.7 g per year. Presently we have 81 TRIGA fuel elements in the core, 55 of them are old aluminium clad elements from the initial criticality while the rest are stainless steel clad elements which had been added later to compensate the uranium consumption. Because 67 % of the elements are older than 40 years, it was necessary to put the history of every element in a database, to get an easy access to all the relevant data for every element in our facility. (author)

  19. Transient behavior during reactivity insertion in the Moroccan TRIGA Mark II reactor using the PARET/ANL code

    International Nuclear Information System (INIS)

    Boulaich, Y.; Nacir, B.; El Bardouni, T.; Boukhal, H.; Chakir, E.; El Bakkari, B.; El Younoussi, C.

    2015-01-01

    Highlights: • PARET model for the Moroccan TRIGA MARK II reactor has been developed. • Transient behavior under reactivity insertion has been studied based on PARET code. • Power factors required by PARET code have been calculated by using MCNP5 code. • The dependence on time of the main thermal-hydraulic parameters was calculated. • Results are largely far to compromise the thermal design limits. - Abstract: A three dimensional model for the Moroccan 2 MW TRIGA MARK II reactor has been developed for thermal-hydraulic and safety analysis by using the PARET/ANL and MCNP5 codes. This reactor is located at the nuclear studies center of Mâamora (CENM), Morocco. The model has been validated through temperature measurements inside two instrumented fuel elements located near the center of the core, at various power levels, and also through the power and fuel temperature evolution after the reactor shutdown (SCRAM). The axial distributions of power factors required by the PARET code have been calculated in each fuel element rod by using MCNP5 code. Based on this thermal-hydraulic model, a safety analysis under the reactivity insertion phenomenon has been carried out and the dependence on time of the main thermal-hydraulic parameters was calculated. Results were compared to the thermal design limits imposed to maintain the integrity of the clad

  20. Estimation of fast neutron fluence in steel specimens type Laguna Verde in TRIGA Mark III reactor; Estimacion de la fluencia de neutrones rapidos en probetas de acero tipo Laguna Verde en el reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Galicia A, J.; Francois L, J. L. [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Ciudad Universitaria, 04510 Ciudad de Mexico (Mexico); Aguilar H, F., E-mail: blink19871@hotmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2015-09-15

    The main purpose of this work is to obtain the fluence of fast neutrons recorded within four specimens of carbon steel, similar to the material having the vessels of the BWR reactors of the nuclear power plant of Laguna Verde when subjected to neutron flux in a experimental facility of the TRIGA Mark III reactor, calculating an irradiation time to age the material so accelerated. For the calculation of the neutron flux in the specimens was used the Monte Carlo code MCNP5. In an initial stage, three sheets of natural molybdenum and molybdenum trioxide (MoO{sub 3}) were incorporated into a model developed of the TRIGA reactor operating at 1 M Wth, to calculate the resulting activity by setting a certain time of irradiation. The results obtained were compared with experimentally measured activities in these same materials to validate the calculated neutron flux in the model used. Subsequently, the fast neutron flux received by the steel specimens to incorporate them in the experimental facility E-16 of the reactor core model operating at nominal maximum power in steady-state was calculated, already from these calculations the irradiation time required was obtained for values of the neutron flux in the range of 10{sup 18} n/cm{sup 2}, which is estimated for the case of Laguna Verde after 32 years of effective operation at maximum power. (Author)

  1. Neutronics analysis of the TRIGA Mark II reactor core and its experimental facilities

    International Nuclear Information System (INIS)

    Khan, R.

    2010-01-01

    The neutronics analysis of the current core of the TRIGA Mark II research reactor is performed at the Atominstitute (ATI) of Vienna University of Technology. The current core is a completely mixed core having three different types of fuels i.e. aluminium clad 20 % enriched, stainless steel clad 20 % enriched and SS clad 70 % enriched (FLIP) Fuel Elements (FE(s)). The completely mixed nature and complicated irradiation history of the core makes the reactor physics calculations challenging. This PhD neutronics research is performed by employing the combination of two best and well practiced reactor simulation tools i.e. MCNP (general Monte Carlo N-particle transport code) for static analysis and ORIGEN2 (Oak Ridge Isotop Generation and depletion code) for dynamic analysis of the reactor core. The PhD work is started to develop a MCNP model of the first core configuration (March 1962) employing fresh fuel composition. The neutrons reaction data libraries ENDF/B-VI is applied taking the missing isotope of Samarium from JEFF3.1. The MCNP model of the very first core has been confirmed by three different local experiments performed on the first core configuration. These experiments include the first criticality, reactivity distribution and the neutron flux density distribution experiment. The first criticality experiment verifies the MCNP model that core achieves its criticality on addition of the 57th FE with a reactivity difference of about 9.3 cents. The measured reactivity worths of four FE(s) and a graphite element are taken from the log book and compared with MCNP simulated results. The percent difference between calculations and measurements ranges from 4 to 22 %. The neutron flux density mapping experiment confirms the model completely exhibiting good agreement between simulated and the experimental results. Since its first criticality, some additional 104-type and 110-type (FLIP) FE(s) have been added to keep the reactor into operation. This turns the current

  2. Operation and maintenance of the 250 kW TRIGA Mark II reactor at the J. Stefan Institute

    International Nuclear Information System (INIS)

    Dimic, V.

    1982-01-01

    Over the last two years the TRIGA Mark II reactor in Ljubljana has been operated at an energy release of about 2250 MWh or about 4200 hours per year. In this period, about 2000 samples were irradiated. Since the last TRIGA Owners' Conference there has been an increase in all operational data because of a very extensive programme of irradiation of molybdenum for the everyday production of technetium-99 m by a solvent extraction method. Because of its age and absolencence replacement of the console electronics was considered some time ago. Therefore, partly new instrumentation was installed this year. A new console is under construction. Furthermore, a new core configuration was established after 7 fresh FLIP fuel elements were delivered by GA. At this time it was noticed that 2 dummy elements are stuck in the upper grid plate. They will be exchanged during the regular maintenance work in August this year. During the last two years the reactor has been operated without any longer shut-down due to technical difficulties. (author)

  3. Study of a new automatic reactor power control for the TRIGA Mark II reactor at University of Pavia

    Energy Technology Data Exchange (ETDEWEB)

    Borio Di Tigliole, A.; Magrotti, G. [Laboratorio Energia Nucleare Applicata (L.E.N.A.), University of Pavia, Via Aselli 41, 27100 (Italy); Cammi, A.; Memoli, V. [Politecnico di Milano, Department of Energy, Nuclear Engineering Division (CeSNEF), Via Ponzio 34/3, 20133 Milano (Italy); Gadan, M. A. [Instrumentation and Control Department, National Atomic Energy Comission of Argentina, University of Pavia (Italy)

    2009-07-01

    The installation of a new Instrumentation and Control (IC) system for the TRIGA Mark-II reactor at University of Pavia has recently been completed in order to assure a safe and continuous reactor operation for the future. The intervention involved nearly the whole IC system and required a channel-by-channel component substitution. One of the most sensitive part of the intervention concerned the Automatic Reactor Power Controller (ARPC) which permits to keep the reactor at an operator-selected power level acting on the control rod devoted to the fine regulation of system reactivity. This controller installed can be set up using different control logics: currently the system is working in relay mode. The main goal of the work presented in this paper is to set up a Proportional-Integral-Derivative (PID) configuration of the new controller installed on the TRIGA reactor of Pavia so as to optimize the response to system perturbations. The analysis have shown that a continuous PID offers generally better results than the relay mode which causes power oscillations with an amplitude of 3% of the nominal power

  4. Development of a software for the control of the quality management system of the TRIGA-Mark III reactor; Desarrollo de un software para el control del sistema de gestion de calidad del reactor TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Herrera A, E. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Hernandez, L.V.; Hernandez, J.A. [UAEM, Depto. de Ingenieria en Computacion, 50000 Toluca, estado de Mexico (Mexico)]. e-mail: eha@nuclear.inin.mx

    2006-07-01

    The quality has not only become one of the essential requirements of the product but rather at the presenme it is a strategic factor key of which depends the bigger part of the organizations, not only to maintain their position in the market but also to assure their survival. The good organizations will have processes, procedures and standards to confront these challenges. The big organizations require of the certification of their administration systems, and once the organization has obtained this certification the following step it is to maintain it. The implementation and certification of an administration system requires of an appropriate operative organization that achieves continuous improvements in their operation. This is the case of the TRIGA Mark III reactor, which contains a computer program that upgrades, it controls and it programs activities to develop in the Installation, allowing one operative organization to the whole personnel of the same one. With the purpose of avoiding activities untimely. (Author)

  5. Computer aided design (CAD) for electronics improvement of the nuclear channels of TRIGA Mark III reactor of the ININ; Diseno asistido por computadora (DAC) para mejorar la electronica de los canales nucleares del reactor TRIGA Mark III del ININ

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez M, J.L.; Rivero G, T.; Aguilar H, F. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)]. e-mail: jlgm@nuclear.inin.mx

    2007-07-01

    The 4 neutron measurement channels of the digital control console (CCD) of the TRIGA Mark III reactor (RTMIII) of the ININ, its were designed and built with the corresponding Quality Guarantee program, being achieved the one licensing to replace the old console. With the time they were carried out some changes to improve and to not solve some problems detected in the tests, verification and validation, requiring to modify the circuits originally designed. In this work the corrective actions carried out to eliminate the Non Conformity generated by these problems, being mentioned the advantages of using modern tools, as the software applied to the Attended Engineering by Computer, and those obtained results are presented. (Author)

  6. Phosphated in aluminium 6061-T651 used in the pool of the TRIGA Mark III nuclear reactor; Fosfatado en aluminio 6061-T651 utilizado en la tina del reactor nuclear TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar H, F.; Espinosa L, J.; Pena B, A.; Perez F, C.; Sanchez C, M.; Vite T, M.; Vite T, J. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    2001-07-01

    We characterized a phosphated coating used a substrate in aluminium 6061-T651, which is used in the container of the TRIGA Mark III nuclear reactor. Characterization was made using MEB and X-ray diffraction techniques. Coating application has the function to prevent the corrosion. Coating was probed to test adhesion in accordance with the Standard ASTM D-4541, and the corrosion process using a salt spray (fog) camera, in accordance with the Standard ASTM B-117, so as we could phosphate the welding cord. These experiences were obtained using a Deep cell. Results obtained are going to phosphate 'in situ' using a mobile device which was patented for the National Institute of Nuclear Research (ININ) in the Mexican Institute of Intellectual Property (INPI). (Author)

  7. Coordination of motor systems of the control bars of TRIGA Mark III reactor, through the use of a PLC; Coordinacion de los sistemas motrices de las barras de control del reactor Triga Mark III, mediante el uso de un PLC

    Energy Technology Data Exchange (ETDEWEB)

    Castro R, P. R.

    2016-07-01

    The use of programmable logic controllers (PLCs) has a wide field in the realization of automatic systems, since is sought that the form of control is easy for any user. In this work, the TRIGA Mark III reactor of Instituto Nacional de Investigaciones Nucleares (ININ) is intended to operate with a programming code in PLC for the automation of the control rods, having uniform wear according to the power required by the user. On the other hand, is proposed to develop an HMI graphical interface for communication via Ethernet, allowing supervision during the reactor operation process and greater protection of operators during reactor startup. The accuracy of the new actuators, as well as their durability, will allow a good performance of the reactor for many years to come. (Author)

  8. Modeling a TRIGA Mark II reactor using the Attila three-dimensional deterministic transport code

    International Nuclear Information System (INIS)

    Keller, S.T.; Palmer, T.S.; Wareing, T.A.

    2005-01-01

    A benchmark model of a TRIGA reactor constructed using materials and dimensions similar to existing TRIGA reactors was analyzed using MCNP and the recently developed deterministic transport code Attila TM . The benchmark reactor requires no MCNP modeling approximations, yet is sufficiently complex to validate the new modeling techniques. Geometric properties of the benchmark reactor are specified for use by Attila TM with CAD software. Materials are treated individually in MCNP. Materials used in Attila TM that are clad are homogenized. Attila TM uses multigroup energy discretization. Two cross section libraries were constructed for comparison. A 16 group library collapsed from the SCALE 4.4.a 238 group library provided better results than a seven group library calculated with WIMS-ANL. Values of the k-effective eigenvalue and scalar flux as a function of location and energy were calculated by the two codes. The calculated values for k-effective and spatially averaged neutron flux were found to be in good agreement. Flux distribution by space and energy also agreed well. Attila TM results could be improved with increased spatial and angular resolution and revised energy group structure. (authors)

  9. Operation experience with the TRIGA Mark II reactor Vienna in the years 1972 through 1974

    International Nuclear Information System (INIS)

    Boeck, H.

    1974-01-01

    Since the last TRIGA Users Conference in Pavia 1972 the TRIGA reactor Vienna was in operation without any larger undesired shut-down. The integral thermal power production by Sept. 1, 1974 was 3420 MWh. The principal work carried out during the last two years on the reactor system was the installation of a new heat exchanger and primary pump both designed for 1 MW steady state operation. Permission was also obtained from the local authority to withdraw up to 90 m 3 /h secondary cooling water from the well. Some troubles were observed with the pulse rod. After nearly 12 years of operation the connection between the piston rod and control rod broke off just below the water surface. Therefore the piston was shot out without withdrawing the pulse rod itself. After locating the trouble the damage was repaired within one day. The SST fuel elements type 110 were received by the end of 1972 for the purpose of power upgrading. All other fuel elements except one are still located in the reactor core and shifted periodically in order to obtain an optimal burnup. A new alarm system was ordered from Hartmann and Braun and is under installation at the moment. In order to facilitate cooperation with the reactor operation personnel and the experimenters in the reactor hall an accurate power indicator has been installed in the reactor hall which allows all experimenters to read the reactor power as accurately as in the control room itself. (U.S.)

  10. Evaluation of the aptitude for the service of the pool of the TRIGA Mark III reactor of the National Institute of Nuclear Research of Mexico

    International Nuclear Information System (INIS)

    Merino C, J.; Gachuz M, M.; Diaz S, A.; Arganis J, C.; Gonzalez R, C.; Nava G, T.; Medina R, M.J.

    2001-01-01

    This work describes the evaluation of the structural integrity of the pool of the TRIGA Mark III reactor of the National Institute of Nuclear Research of Mexico, which was realized in July 2001, as an element to determine those actions for preventive and corrective maintenance which owner must do it for a safety and efficient operation of the component in the next years. (Author)

  11. Phosphated in aluminium 6061-T651 used in the pool of the TRIGA Mark III nuclear reactor

    International Nuclear Information System (INIS)

    Aguilar H, F.; Espinosa L, J.; Pena B, A.; Perez F, C.; Sanchez C, M.; Vite T, M.; Vite T, J.

    2001-01-01

    We characterized a phosphated coating used a substrate in aluminium 6061-T651, which is used in the container of the TRIGA Mark III nuclear reactor. Characterization was made using MEB and X-ray diffraction techniques. Coating application has the function to prevent the corrosion. Coating was probed to test adhesion in accordance with the Standard ASTM D-4541, and the corrosion process using a salt spray (fog) camera, in accordance with the Standard ASTM B-117, so as we could phosphate the welding cord. These experiences were obtained using a Deep cell. Results obtained are going to phosphate 'in situ' using a mobile device which was patented for the National Institute of Nuclear Research (ININ) in the Mexican Institute of Intellectual Property (INPI). (Author)

  12. Computer aided design (CAD) for electronics improvement of the nuclear channels of TRIGA Mark III reactor of the ININ

    International Nuclear Information System (INIS)

    Gonzalez M, J.L.; Rivero G, T.; Aguilar H, F.

    2007-01-01

    The 4 neutron measurement channels of the digital control console (CCD) of the TRIGA Mark III reactor (RTMIII) of the ININ, its were designed and built with the corresponding Quality Guarantee program, being achieved the one licensing to replace the old console. With the time they were carried out some changes to improve and to not solve some problems detected in the tests, verification and validation, requiring to modify the circuits originally designed. In this work the corrective actions carried out to eliminate the Non Conformity generated by these problems, being mentioned the advantages of using modern tools, as the software applied to the Attended Engineering by Computer, and those obtained results are presented. (Author)

  13. Determination of the fluence profile in three dimension for the thermal column of the TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Herrera A, E.; Urena N, F.; Delfin L, A.; Garcia M, T.

    2006-01-01

    In this work the results of the dosimetric properties of the lithium carbonate are presented (detecting), before the thermal neutrons. The process consists on irradiating samples of lithium carbonate in the installation of the thermal column of the TRIGA Mark III reactor, with a controlled period and with time intervals of 20 hours of irradiation. It is necessary to mention that the detectors were placed in different internal positions of the thermal column. With the purpose of being used these results for future studies, like it is the fluence profile in the thermal column. To use the BNCT technique (Boron Neutron Capture Therapy). Which is a binary technique that requires the simultaneous presence of a neutron flux with appropriate energy and a neutron captor (10B), those which interacting to attack to the tumor cells without producing significant damage to the tissues when both agents are separated. (Author)

  14. Neutron flux measurement in the thermal column of the Malaysian TRIGA mark II reactor with MCNP verification

    International Nuclear Information System (INIS)

    Abdel Munem, E.; Shukri, A.; Tajuddin, A.A.

    2006-01-01

    A study of the thermal column of the Malaysian TRIGA Mark II reactor, forming part of a feasibility study for BNCT was proposed in 2001. In the current study, pure metals were used to measure the neutron flux at selected points in the thermal column and the neutron flux determined using SAND-II. Monte Carlo simulation of the thermal column was also carried out. The reactor core was homogenized and calculations of the neutron flux through the graphite stringers performed using MCNP5. The results show good agreement between the measured flux and the MCNP calculated flux. An obvious extension from this is that the MCNP neutron flux output can be utilized as an input spectrum for SAND-II for the flux iteration. (author)

  15. Development of a software for the control of the quality management system of the TRIGA-Mark III reactor

    International Nuclear Information System (INIS)

    Herrera A, E.; Hernandez, L.V.; Hernandez, J.A.

    2006-01-01

    The quality has not only become one of the essential requirements of the product but rather at the present time it is a strategic factor key of which depends the bigger part of the organizations, not only to maintain their position in the market but also to assure their survival. The good organizations will have processes, procedures and standards to confront these challenges. The big organizations require of the certification of their administration systems, and once the organization has obtained this certification the following step it is to maintain it. The implementation and certification of an administration system requires of an appropriate operative organization that achieves continuous improvements in their operation. This is the case of the TRIGA Mark III reactor, which contains a computer program that upgrades, it controls and it programs activities to develop in the Installation, allowing one operative organization to the whole personnel of the same one. With the purpose of avoiding activities untimely. (Author)

  16. Coordination of motor systems of the control bars of TRIGA Mark III reactor, through the use of a PLC

    International Nuclear Information System (INIS)

    Castro R, P. R.

    2016-01-01

    The use of programmable logic controllers (PLCs) has a wide field in the realization of automatic systems, since is sought that the form of control is easy for any user. In this work, the TRIGA Mark III reactor of Instituto Nacional de Investigaciones Nucleares (ININ) is intended to operate with a programming code in PLC for the automation of the control rods, having uniform wear according to the power required by the user. On the other hand, is proposed to develop an HMI graphical interface for communication via Ethernet, allowing supervision during the reactor operation process and greater protection of operators during reactor startup. The accuracy of the new actuators, as well as their durability, will allow a good performance of the reactor for many years to come. (Author)

  17. Verification of Monte Carlo calculations of the neutron flux in the carousel channels of the TRIGA Mark II reactor, Ljubljana

    International Nuclear Information System (INIS)

    Jacimovic, R.; Maucec, M.; Trkov, A.

    2002-01-01

    In this work experimental verification of Monte Carlo neutron flux calculations in the carousel facility (CF) of the 250 kW TRIGA Mark II reactor at the Jozef Stefan Institute is presented. Simulations were carried out using the Monte Carlo radiation-transport code, MCNP4B. The objective of the work was to model and verify experimentally the azimuthal variation of neutron flux in the CF for core No. 176, set up in April 2002. '1'9'8Au activities of Al-Au(0.1%) disks irradiated in 11 channels of the CF covering 180'0 around the perimeter of the core were measured. The comparison between MCNP calculation and measurement shows relatively good agreement and demonstrates the overall accuracy with which the detailed spectral characteristics can be predicted by calculations.(author)

  18. Boron Neutron Capture Therapy at the TRIGA Mark II of Pavia, Italy - The BNCT of the diffuse tumours

    Energy Technology Data Exchange (ETDEWEB)

    Altieri, S.; Bortolussi, S.; Stella, S.; Bruschi, P.; Gadan, M.A. [University of Pavia (Italy); INFN - National Institute for Nuclear Physics, of Pavia (Italy)

    2008-10-29

    The selectivity based on the B distribution rather than on the irradiation field makes Boron neutron Capture Therapy (BNCT) a valid option for the treatment of the disseminated tumours. As the range of the high LET particles is shorter than a cell diameter, the normal cells around the tumour are not damaged by the reactions occurring in the tumoral cells. PAVIA 2001: first treatment of multiple hepatic metastases from colon ca by BNCT and auto-transplantation technique: TAOrMINA project. The liver was extracted after BPA infusion, irradiated in the Thermal Column of the Pavia TRIGA Mark II reactor, and re-implanted in the patient. Two patients were treated, demonstrating the feasibility of the therapy and the efficacy in destroying the tumoral nodules sparing the healthy tissues. In the last years, the possibility of applying BNCT to the lung tumours using epithermal collimated neutron beams and without explanting the organ, is being explored. The principal obtained results of the BNCT research are presented, with particular emphasis on the following aspects: a) the project of a new thermal column configuration to make the thermal neutron flux more uniform inside the explanted liver, b) the Monte Carlo study by means of the MCNP code of the thermal neutron flux distribution inside a patient's thorax irradiated with epithermal neutrons, and c) the measurement of the boron concentration in tissues by (n,{alpha}) spectroscopy and neutron autoradiography. The dose distribution in the thorax are simulated using MCNP and the anthropomorphic model ADAM. To have a good thermal flux distribution inside the lung epithermal neutrons must be used, which thermalize crossing the first tissue layers. Thermal neutrons do not penetrate and the obtained uniformity is poor. In the future, the construction of a PGNAA facility using a horizontal channel of the TRIGA Mark II is planned. With this method the B concentration can be measured also in liquid samples (blood, urine) and

  19. Core map generation for the ITU TRIGA Mark II research reactor using Genetic Algorithm coupled with Monte Carlo method

    Energy Technology Data Exchange (ETDEWEB)

    Türkmen, Mehmet, E-mail: tm@hacettepe.edu.tr [Nuclear Engineering Department, Hacettepe University, Beytepe Campus, Ankara (Turkey); Çolak, Üner [Energy Institute, Istanbul Technical University, Ayazağa Campus, Maslak, Istanbul (Turkey); Ergün, Şule [Nuclear Engineering Department, Hacettepe University, Beytepe Campus, Ankara (Turkey)

    2015-12-15

    Highlights: • Optimum core maps were generated for the ITU TRIGA Mark II Research Reactor. • Calculations were performed using a Monte Carlo based reactor physics code, MCNP. • Single-Objective and Multi-Objective Genetic Algorithms were used for the optimization. • k{sub eff} and ppf{sub max} were considered as the optimization objectives. • The generated core maps were compared with the fresh core map. - Abstract: The main purpose of this study is to present the results of Core Map (CM) generation calculations for the İstanbul Technical University TRIGA Mark II Research Reactor by using Genetic Algorithms (GA) coupled with a Monte Carlo (MC) based-particle transport code. Optimization problems under consideration are: (i) maximization of the core excess reactivity (ρ{sub ex}) using Single-Objective GA when the burned fuel elements with no fresh fuel elements are used, (ii) maximization of the ρ{sub ex} and minimization of maximum power peaking factor (ppf{sub max}) using Multi-Objective GA when the burned fuels with fresh fuels are used. The results were obtained when all the control rods are fully withdrawn. ρ{sub ex} and ppf{sub max} values of the produced best CMs were provided. Core-averaged neutron spectrum, and variation of neutron fluxes with respect to radial distance were presented for the best CMs. The results show that it is possible to find an optimum CM with an excess reactivity of 1.17 when the burned fuels are used. In the case of a mix of burned fuels and fresh fuels, the best pattern has an excess reactivity of 1.19 with a maximum peaking factor of 1.4843. In addition, when compared with the fresh CM, the thermal fluxes of the generated CMs decrease by about 2% while change in the fast fluxes is about 1%.Classification: J. Core physics.

  20. The study of time-dependent neutronics parameters of the 2MW TRIGA Mark II Moroccan research reactor using BUCAL1 computer code

    International Nuclear Information System (INIS)

    Bakkari, B. El; Nacir, B.; El Younoussi, C.; Boulaich, Y.; Riyach, I.; Otmani, S.; Marcih, I.; Elbadri, H.; El Bardouni, T; Merroun, O.; Boukhal, H.; Zoubair, M.; Htet, A.; Chakir, M.

    2010-01-01

    The 2-MW TRIGA MARK II research reactor at Centre National de l'Energie, des Sciences et des Techniques Nucleaires (CNESTEN) achieved initial criticality on May 2, 2007 with 71 fuel elements. The reactor is designed to effectively implement the various fields of basic nuclear research, manpower and training and production of radioisotopes for their use in agriculture, industry and medicine. This work aims to study the time-dependent neutronics parameters of the TRIGA reactor for elaborating and planning of an in-core fuel management strategy to maximize the utilization of the TRIGA fluxes, using a new elaborated burnup computer code called 'BUCAL1'. The code can be used to aid in analysis, prediction, and optimization of fuel burnup performance in a nuclear reactor. It was developed to incorporate the neutron absorption tally/reaction information generated directly by MCNP5 code in the calculation of fissioned or neutron-transmuted isotopes for multi-fueled regions. The use of Monte Carlo method and punctual cross section data characterizing the MCNP code allows an accurate simulation of neutron life cycle in the reactor, and the integration of data on the entire energy spectrum, thus a more accurate estimation of results than deterministic code can do. Also, for the purpose of this study, a full-model of the TRIGA reactor was developed using the MCNP5 code. The validation of the MCNP model of the TRIGA reactor was made by benchmarking the reactivity experiments. (author)

  1. Recently-developed neutron activation analysis techniques utilizing the University of California at Irvine TRIGA Mark I reactor

    International Nuclear Information System (INIS)

    Guinn, V.P.; Chambless, D.; Cortes T, E.; DeLancey, K.; Garzonov, E.; Miller, D.A.; Miller, G.E.; Purcell, M.A.

    1976-01-01

    The University of California at Irvine (UCI) 250 kW TRIGA Mark I reactor is used extensively for neutron activation analysis (NAA) studies. These particularly include basic technique studies and application studies in the fields of environmental pollution, crime investigation, archaeology, oceanography, and geochemistry. In recent NAA studies at UCI, a number of techniques have been developed which considerably improve the usefulness of such a research reactor for NAA work, and which should be of interest and use to others. Six of these techniques will be described in further detail in the full paper. They are as follows: development and use of (1) an automated high-precision rapid transfer system for instrumental NAA measurements with induced activities having half lives as short as 0.5 second, (2) an automated measurement system and computer program for making accurate dead-time corrections under conditions where the Ge(Li) spectrometer deadtime is changing rapidly during the counting period, (3) a technique to minimize the loss of mercury from samples during reactor irradiation via the use of dry-ice-packed, vented TRIGA rotary rack tubes, (4) a technique for compacting powdered samples, by pre-irradiation treatment with a solution of paraffin in carbon disulfide, to provide reproducible irradiation and counting geometries, (5) a method utilizing hydrated antimony pentoxide (HAP) as a pre-irradiation treatment material for removal of sodium from aqueous and wet-ashed samples, and (6) a computerized system for predicting in advance of activation, from approximate known elemental compositions, the total counting rate, deadtime, spectrum shape, principal photopeaks, and approximate actual lower limits of instrumental NAA detection of designated elements for any selected irradiation and decay times. (author)

  2. Operation experience at the TRIGA Mark III reactor FRN within the last two years

    International Nuclear Information System (INIS)

    Rau, G.

    1976-01-01

    A survey is given of the history of FRN-reactor operation since the last TRIGA conference. In 1975, the reactor had been operated for 830 MWh and had been pulsed 1050 times. In the first half of 1976, an appreciable Increase of reactor activities took place. In this time interval, the integrated power amounted to 996 MWh and the number of released pulses to 1024. In 1975, an important event was the exchange of the defective rotary specimen rack against a water-operated type. For this purpose, the whole core had to be unloaded and the pool water had to be removed. In this connection, damages at the beam-port weldings had been discovered and had to be repaired immediately. In December 1975, a new core configuration had been set up by adding ten spare fuel elements into the F-resp. G-ring. The gain of excess reactivity amounted to approximately 1,8 $. This however allowed reactor operation without disturbance by Xe-poisoning only for a limited time interval. (author)

  3. Characterization of the neutron flux in the Hohlraum of the thermal column of the TRIGA Mark III reactor of the ININ; Caracterizacion del flujo neutronico en el Hohlraum de la columna termica del reactor TRIGA Mark III del ININ

    Energy Technology Data Exchange (ETDEWEB)

    Delfin L, A.; Palacios, J.C.; Alonso, G. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: adl@nuclear.inin.mx

    2006-07-01

    Knowing the magnitude of the neutron flux in the reactor irradiation facilities, is so much importance for the operation of the same one, like for the investigation developing. Particularly, knowing with certain precision the spectrum and the neutron flux in the different positions of irradiation of a reactor, it is essential for the evaluation of the results obtained for a certain irradiation experiment. The TRIGA Mark III reactor account with irradiation facilities designed to carry out experimentation, where the reactor is used like an intense neutron source and gamma radiation, what allows to make irradiations of samples or equipment in radiation fields with components and diverse levels in the different facilities, one of these irradiation facilities is the Thermal Column where the Hohlraum is. In this work it was carried out a characterization of the neutron flux inside the 'Hohlraum' of the irradiation facility Thermal Column of the TRIGA Mark III reactor of the Nuclear Center of Mexico to 1 MW of power. It was determined the sub cadmic neutron flux and the epi cadmic by means of the neutron activation technique of thin sheets of gold. The maps of the distribution of the neutron flux for both energy groups in three different positions inside the 'Hohlraum' are presented, these maps were obtained by means of the irradiation of undressed thin activation sheets of gold and covered with cadmium in arrangements of 10 x 12, located parallel to 11.5 cm, 40.5 cm and 70.5 cm to the internal wall of graphite of the installation in inverse address to the position of the reactor core. Starting from the obtained values of neutron flux it was found that, for the same position of the surface of irradiation of the experimental arrangement, the relative differences among the values of neutron flux can be of 80%, and that the differences among different positions of the irradiation surfaces can vary until in a one order of magnitude. (Author)

  4. Dry reloading and packaging of spent fuel at TRIGA MARK I reactor of Medical University Hanover (MHH), Germany

    International Nuclear Information System (INIS)

    Haferkamp, D.

    2008-01-01

    Between 1994 and 1998 the equipment for dry reloading of a research reactor was developed by Noell, which was funded by the German Federal Government and State of Saxonia. The task of this development programme was the design and delivery of an equipment able to load the spent fuel into the shipping casks in a dry mode for research reactors, where wet loading inside the storage pool is impossible. ALARA and infrastructure conditions had to be taken into consideration. Most of the research reactors of TRIGA MARK I type or WWR-SM have operating modes for handling of spent fuel inside the pond or for transfer of spent fuel from pond to dry/wet storage pools. On the other hand, most of them cannot handle heavy weighted shipping casks inside the reactor building because of the crane capacity, or inside water pool because of dimensions and weight of shipping casks. A typical licensed normal operating procedure for spent fuel in research reactors (TRIGA MARK I) is shown. Dry unloading procedure is described. Additionally to the normal operating procedures at the MHH research reactor the following steps were necessary: - dry packaging of spent fuel elements into the loading units (six packs) in order to minimise the transfer and loading steps between the pool and shipping cask; - transfer of spent fuel loading units from dry storage pool to the shipping cask (outside the reactor building) in a shielded transfer cask; - dry reloading of loading units, into the shipping casks outside the reactor building. The Dry Reloading Equipment implies the following 5 items: 1. loading units (six packs), which includes: - capacity up to six spent fuel elements; - criticality safe placement of spent fuel elements; - handling of several spent fuel elements in an aluminium loading unit. 2. Special Transfer Cask, which includes: - shielded housing with locks; - gripper inside housing; - hoist outside housing; - computer aided operation mode for loading and unloading. 3. Transfer Vehicle

  5. Visual inspection system and sipping design for spent fuel at TRIGA MARK III reactor of Mexico

    International Nuclear Information System (INIS)

    Delfin, A.; Mazon, R.

    2002-01-01

    In the framework of the Technical Cooperation Regional Project for Latin America RLA/4/018 for the biennium 2001-2002, one of the activities identified is the characterization of spent fuel. Of these activities an important one is not doubt the physical condition of spent fuel because an appropriate identification of the fuel status will prevent problems of fuel leaks, corrosion problems etc. As part of the activities of the project was decided that countries no having visual inspection and sipping systems should be very desirable to have them as a result of this project. The Triga reactor of Mexico does not have both of them, therefore, it was decided the need of having both system. The paper describe first the way we designed and constructed a remote Visual Inspection System and example of how is operated. Along the experience and problems we have had with the system. Also we will present the design of the Sipping system were two option were considered. First to take a sample of water after a convenient period of time passing through a circuit to a multichannel analyzer and to identify leakage by way of measuring Caesium-137. Second, exists the possibility that the Stainless Steel sleeve of the fuel has only very small failures, so it is going to be very difficult to have leakages unless the fuel is hot. Therefore we are evaluating the possibility of using heaters to increase the temperature of the fuel and succeed on detecting leakages. The results - we hope - will be ready to be presented at the meeting. (author)

  6. 10th European TRIGA users conference

    International Nuclear Information System (INIS)

    Anon.

    1988-01-01

    Abstracts of 46 papers on various aspects of Triga reactors (mainly Triga Mark 2 reactors) are given, according to the main headings: reactor operation and maintenance experience; new developments and improvements of Triga components and systems, including instrumentation; fuel and fuel management; safety aspects, licensing and radiation protection; experiments with Triga reactors; radiochemistry, radioisotope production and NAA; reactor physics. (qui)

  7. Determination of the neutrons energy spectrum in the central thimble of the reactor core TRIGA Mark III; Determinacion del espectro de energia de los neutrones en el dedal central del nucleo del reactor TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Parra M, M. A.; Luis L, M. A. [Universidad Autonoma Metropolitana, Unidad Azcapotzalco, Division de Ciencias Basicas, Av. San Pablo No. 180, Col. Reynosa Tamaulipas, 02200 Mexico D. F. (Mexico); Raya A, R.; Cruz G, H. S., E-mail: roberto.raya@inin.gob.mx [ININ, Departamento del Reactor, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2013-10-15

    This work presents the measurement of the neutrons spectrum in energies in the central thimble of the reactor TRIGA Mark III to a power of 1 MW in stationary state, with the core in the center of the pool. To achieve this objective, several thin sheets were irradiated (one at the time) in the same position of the core. The activation probes were selected in such a way that covered the energy range (1 x 10{sup -10} to 20 MeV) of the neutrons spectrum in the reactor core, for this purpose thin sheets were used of {sup 197}Au, {sup 58}Ni, {sup 115}In, {sup 24}Mg, {sup 27}Al, {sup 58}Fe, {sup 59}Co and {sup 63}Cu. After the irradiation, the high energy gamma emissions of the activated thin sheets were measured by means of gamma spectrometry, in a counting system of high resolution, with a Hyper pure Germanium detector, obtaining this way the activity induced in the thin sheets whose magnitude is proportional to the intensity of the neutrons flow, this activity together to a theoretical initial spectrum are the main entrance data of the computational code SANDBP (Hungarian version of the code Sand-II) that uses the unfolding method for the calculation of the spectrum. (Author)

  8. Development of the user interface for visualization of the auxiliary systems of the TRIGA Mark III nuclear reactor; Desarrollo de la interface de usuario para la visualizacion de los sistemas auxiliares del reactor nuclear Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Merced D, J. E.

    2016-07-01

    The Instituto Nacional de Investigaciones Nucleares (ININ) has a nuclear research reactor type swimming pool with movable core cooled and moderate with light water. The nominal maximum power of the reactor is 1 MW in steady-state operation and can be pulsed at a maximum power of 2,000 MW for approximately 10 milliseconds. This reactor is mainly used to study the effects of radiation on various materials and substances. In 2001 the new control console of the nuclear reactor was installed which was based on two digital computers, one computer controls the bar management mechanisms and the other the systems to the reactor operator. In 2004, the control computer was replaced and the software was updated. Within the modernization and/or updating of the TRIGA Mark III reactor of ININ, is intended (theme of this work) to develop the user interface for the visualization of the auxiliary systems, through a Man-Machine Interface module for the renewal process of the control console. The man-machine interface system to be developed will have communication with the programmable logic controllers that will be constantly monitored and controlled to obtain real-time variables of the reactor behavior. (Author)

  9. Inspection with non destructive assay techniques of the aluminium coating of the TRIGA Mark III reactor vat; Inspeccion con tecnicas de ensayos no destructivos del recubrimiento de aluminio de la tina del reactor TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Reyes A, A.I.; Gonzalez M, A.; Castaneda J, G.; Rivera M, H.; Sandoval G, I. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    2001-07-01

    In June 2000, the Reactor Department assigned to the Scientific Research Direction of the National Institute of Nuclear Research requested to the Non-destructive Assays Laboratory (LEND), assigned to the Materials Science Management, the inspection and measurement of thickness of the aluminium coating (liner) of the TRIGA Mark III reactor vat with non-destructive assay techniques, due to that the aluminium coating is exposed mainly to undergo slimming on its back side due to corrosion phenomena. Activity that was able to be carried out from april until august 2001. It is worth pointing out that this type of inspection with these techniques was realized by first time. The non-destructive assays (NDA) are techniques which use indirect physical methods for inspecting the sanitation of components in process or in service, for detect lack of continuity or defects which affect their quality or usefulness. The application of those do not alter the physical, chemical, mechanical or dimensional properties of the part subject of inspection. The results of the application of the ultrasound inspection techniques, industrial radiography and penetrating liquids are presented. (Author)

  10. Development and validation of a model TRIGA Mark III reactor with code MCNP5; Desarrollo y validacion de un modelo del reactor Triga Mark III con el codigo MCNP5

    Energy Technology Data Exchange (ETDEWEB)

    Galicia A, J.; Francois L, J. L. [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Ciudad Universitaria, 04510 Ciudad de Mexico (Mexico); Aguilar H, F., E-mail: blink19871@hotmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2015-09-15

    The main purpose of this paper is to obtain a model of the reactor core TRIGA Mark III that accurately represents the real operating conditions to 1 M Wth, using the Monte Carlo code MCNP5. To provide a more detailed analysis, different models of the reactor core were realized by simulating the control rods extracted and inserted in conditions in cold (293 K) also including an analysis for shutdown margin, so that satisfied the Operation Technical Specifications. The position they must have the control rods to reach a power equal to 1 M Wth, were obtained from practice entitled Operation in Manual Mode performed at Instituto Nacional de Investigaciones Nucleares (ININ). Later, the behavior of the K{sub eff} was analyzed considering different temperatures in the fuel elements, achieving calculate subsequently the values that best represent the actual reactor operation. Finally, the calculations in the developed model for to obtain the distribution of average flow of thermal, epithermal and fast neutrons in the six new experimental facilities are presented. (Author)

  11. Behavior of exposed human lymphocytes to a neutron beam of the Reactor TRIGA Mark III; Comportamiento de linfocitos humanos expuestos a un haz de neutrones del Reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Carbajal R, M. I.; Arceo M, C.; Aguilar H, F.; Guerrero C, C., E-mail: citlali.guerrero@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2012-10-15

    The living beings are permanently exposed to radiations of natural origin: cosmic and geologic, as well as the artificial radiations that come from sources elaborated by the man. The artificial sources have an important use in the medical area. Particularly has been increased the neutrons use due to the effectiveness that they have to damage the cells with regard to other radiation types. The biological indicator of exposition to ionizing radiation more reliable is the chromosomal aberrations study, specifically the dicentrics in human lymphocytes. This test allows, establishing the exposition dose in function of the damage quantity. The dicentrics have a behavior in function of the dose. The calibration curve that describes this behavior is specific for each type of ionizing radiation. In the year 2006 beginning was given to the expositions of human lymphocytes to a neutron beam generated in the reactor TRIGA Mark III of the Instituto Nacional de Investigaciones Nucleares (ININ) in Mexico. Up to 2008 the response dose curve comprised an interval of exposition time of up to 30 minutes. Moreover, the interval between 10 an 20 minutes is included, since was observed that this last is indispensable for the adjustment waited in a lineal model. (Author)

  12. Evaluation of the aptitude for the service of the pool of the TRIGA Mark III reactor of the National Institute of Nuclear Research of Mexico; Evaluacion de la aptitud para el servicio de la piscina del reactor TRIGA Mark III del Instituto Nacional de Investigaciones Nucleares de Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Merino C, J.; Gachuz M, M.; Diaz S, A.; Arganis J, C.; Gonzalez R, C.; Nava G, T.; Medina R, M.J. [Departamento de Sintesis y Caracterizacion de Materiales del ININ, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    2001-07-01

    This work describes the evaluation of the structural integrity of the pool of the TRIGA Mark III reactor of the National Institute of Nuclear Research of Mexico, which was realized in July 2001, as an element to determine those actions for preventive and corrective maintenance which owner must do it for a safety and efficient operation of the component in the next years. (Author)

  13. Safety evaluation for instrumentation and control system upgrading project of Malaysian TRIGA MARK II PUSPATI Research reactor

    International Nuclear Information System (INIS)

    Ridha Roslan; Nik Mohd Faiz Khairuddin

    2013-01-01

    Full-text: Malaysian TRIGA MARK II research reactor has been in safe operation since its first criticality in 1982. The reactor is licensed to be operated by Malaysian Nuclear Agency to perform training and research development related activities. Due to its extensive operation since last three decades, the option of modifications for safety and safety-related item and component become a necessary to replace the outdated equipment to a stat-of-art, reliable technologies. This paper will present the current regulatory activities performed by Atomic Energy Licensing Board (AELB) to ensure the upgrading of analogue to digital instrumentation and control system is implemented in safe manner. The review activity includes documentation review, manufacturer quality audit and on-site inspection for commissioning. The review performed by AELB is based on The International Atomic Energy Agency (IAEA) Safety Requirements NS-R-4, entitled Safety of Research Reactors. During this endeavour, AELB seeks technical cooperation from Korea Institute of Nuclear Safety (KINS), the nuclear experts organization of the country of origin of the instrumentation and control technology. The regulatory activity is still on-going and is expected to be completed by issuance of Authorization for Restart on December 2013. (author)

  14. Systematical investigations of the emission of carbon 14 from a TRIGA-Mark-II reactor - methods and results

    International Nuclear Information System (INIS)

    Pfeiffer, K.J.

    1981-01-01

    Almost no information is available about the extent of the carbon-14 releases from a research reactor. For this reason this report is dealing with the emission of C-14 from the Vienna TRIGA-Mark-II reactor. In addition the resulting radiation exposure is estimated. Due to the low activity concentrations of C-14 in research reactor effluents special requirements are necessary for sampling and measuring. A technique providing both sufficient lower limit of detection and little effort of sample preparation was developed. Carbon dioxide was trapped by bubbling air taken from the stack through washing bottles containing an aqueous solution of sodium hydroxide. After sampling a precipitate of CaCO 3 was formed and about 8 g of calcium carbonate were counted as a gel suspension by liquid scintillation counting. The formation of the gel was provided by mixing water with a scintillation cocktail originally developed for uptake of high quantities of aqueous solutions. The resulting lower limit of detection was about 50 Bq/kg carbon being equivalent to 9mBq/m 3 air. Concluding the measurements, which were carried out by weekly counting and a period of some 14 months, a normalized release rate of about 280 Bq (7, 1μCi) was found. This release rate is somewhat higher than the reported values for power reactors, because the main activity is produced by activation of air in experimental equipments. (author)

  15. Environmental impact assessment of Ar-41 released by the normal operation of TRIGA-Mark 2 research reactor

    International Nuclear Information System (INIS)

    Qassoud, D.; Soufi, I.; Ziagos, J.; Demir, Z

    2007-01-01

    Full text: In accordance with the international regulation of nuclear safety and radiological protection of the environment applicable to the basic nuclear installations, category in which the Triga-Mark 2 research reactor is considered, an assesment of the impact in to the environment of the Ar-41 radioelement is accomplished. This radioelement is released by the normal operation of this reactor. The assessment is based on the characteristics of a Moroccan site (where the reactor is installed). It is carried out using CEA Gaussian models and mathematical models developed in LLNL. Considering the assumptions of impact assessments of the radioactivity in the atmosphere, the most important exposure is relatively corresponding to 1 Km from the reactor. This exposure is approximately 0,07% of the lawful limit. Beyond this locality, the exposure becomes lower than 0,02% of this limit. Beyond 5 Km, it becomes lower than ten nono-Sivert. In the basis of the site radiological baseline, the environmental impact of Ar-41 released in normal operation of the reactor is negligible in the studied case. [fr

  16. The past and the future in the forty years of the IPR-R1 TRIGA MARK I reactor operation

    International Nuclear Information System (INIS)

    Maretti Junior, Fausto

    2008-01-01

    Full text: The nuclear IPR-R1 TRIGA Mark I Reactor operating in the Nuclear Technology Development Center, originally Institute for Radioactive Research in Minas Gerais, Brazil, was dedicated in November 11, 1960. Initially operating for the production of radioisotopes for different uses, it started later to be used in large scale for neutron activation analysis and training of operators for nuclear power plants. Many improvements have been made throughout these years to provide a better performance in its operation and safety conditions. A new cooling system to operate until 300 kW, a new control rod mechanism, an aluminum tank for the reactor pool, an optimization in the pneumatic system, a new reactor control console and a general remodeling of the reactor laboratory were some of the improvements added. During these years a lot of irradiations, analysis , MSc and PhD thesis, training courses and isotopes production take place at the reactor. This paper describes the improvements made, the results obtained during the past 40 years, type of works realized, isotopes produced, the neutron activation analysis and the precautions taken to ensure future safe operation of the reactor to give operators better conditions of safe work. (authors)

  17. Determination of the neutrons energy spectrum in the central thimble of the reactor core TRIGA Mark III

    International Nuclear Information System (INIS)

    Parra M, M. A.; Luis L, M. A.; Raya A, R.; Cruz G, H. S.

    2013-10-01

    This work presents the measurement of the neutrons spectrum in energies in the central thimble of the reactor TRIGA Mark III to a power of 1 MW in stationary state, with the core in the center of the pool. To achieve this objective, several thin sheets were irradiated (one at the time) in the same position of the core. The activation probes were selected in such a way that covered the energy range (1 x 10 -10 to 20 MeV) of the neutrons spectrum in the reactor core, for this purpose thin sheets were used of 197 Au, 58 Ni, 115 In, 24 Mg, 27 Al, 58 Fe, 59 Co and 63 Cu. After the irradiation, the high energy gamma emissions of the activated thin sheets were measured by means of gamma spectrometry, in a counting system of high resolution, with a Hyper pure Germanium detector, obtaining this way the activity induced in the thin sheets whose magnitude is proportional to the intensity of the neutrons flow, this activity together to a theoretical initial spectrum are the main entrance data of the computational code SANDBP (Hungarian version of the code Sand-II) that uses the unfolding method for the calculation of the spectrum. (Author)

  18. Neutron activation analysis at CDTN/CNEN using the IPR-R1 Triga Mark I reactor

    International Nuclear Information System (INIS)

    Menezes, Maria Angela de B.C.; Maretti Junior, Fausto; Kastner, Geraldo Frederico; Amaral, Angela Maria; Souza, Wagner de

    2009-01-01

    This paper describes in summary the activities developed by the Laboratory for Neutron Activation Analysis since the starting up of the IPR-R1 TRIGA Mark I research reactor in 1960. This Laboratory is located at Centro de Desenvolvimento da Tecnologia Nuclear (Nuclear Technology Development Centre) / Comissao Nacional de Energia Nuclear (Brazilian Commission for Nuclear Energy), CDTN/CNEN. The activities of the Laboratory comprise the delayed fission neutron activation analysis, instrumental (comparative and parametric methods) and radiochemical / chemical methods. These methods are responsible for significant percentage of CDTN's analytical demand, meeting the clients' analytical needs and researches developed by the Laboratory, by CDTN and by other institutions. Over the years the work has been linked to the goals of the country and the institutions. Nowadays the neutron activation analysis is responsible for 70% of the analytical demand and the k 0 - Instrumental method for 80% of this demand answering clients' request and researches. In Brazil, CDTN is the only Institute that fully masters the Instrumental Neutron Activation Analysis k 0 -method using its own nuclear reactor. (author)

  19. Development of the user interface for visualization of the auxiliary systems of the TRIGA Mark III nuclear reactor

    International Nuclear Information System (INIS)

    Merced D, J. E.

    2016-01-01

    The Instituto Nacional de Investigaciones Nucleares (ININ) has a nuclear research reactor type swimming pool with movable core cooled and moderate with light water. The nominal maximum power of the reactor is 1 MW in steady-state operation and can be pulsed at a maximum power of 2,000 MW for approximately 10 milliseconds. This reactor is mainly used to study the effects of radiation on various materials and substances. In 2001 the new control console of the nuclear reactor was installed which was based on two digital computers, one computer controls the bar management mechanisms and the other the systems to the reactor operator. In 2004, the control computer was replaced and the software was updated. Within the modernization and/or updating of the TRIGA Mark III reactor of ININ, is intended (theme of this work) to develop the user interface for the visualization of the auxiliary systems, through a Man-Machine Interface module for the renewal process of the control console. The man-machine interface system to be developed will have communication with the programmable logic controllers that will be constantly monitored and controlled to obtain real-time variables of the reactor behavior. (Author)

  20. Determination of the subcadmium flux in the Triga Mark III reactor of the Nuclear Center in Mexico

    International Nuclear Information System (INIS)

    Rodiguez V, F.J.

    1975-01-01

    The determination of the subcadmium flux profile (neutrons with energy between 0 and 0.4 eV approximatley) in the core of the reactor Triga Mark III in the Nuclear Center of Mexico was made. The technique used for that purpose consists in placing alternativelly indium sheets covered and uncovered with cadmium and separated by fragments of aluminium 2.54cm wide in an aluminium tube whose external diameter reaches 0.635cm. This tube is introduced in each of the 21 axial irradiation places of the sheets the activity of gamma rays of 1.293 MeV of In-116m produced during the irradiation, is measured using a monochannel analyzer. We obtain graphs of the specific counting ratio vs position for the sheets uncovered and covered with cadmium; using quadratic interpolation we compute in each position the missing specific measuring ratio. The difference between the specific counting ratios with our cadmium and with cadmium multiplied by a constant gives the subcadmium flux in the z point. For irradiation at 10 watts, 1 Kilowatt and 1 megawatt the results show profiles which in general terms are in accordance with those which were obtained theoretically for a cylyndrical reactor using group theory. The greatest flow given by the manufacturer of the reactor is in the values range obtained experimentally.For the calculations, the method uses a FORTRAN IV program so that the determinations can be made routinely. (author)

  1. Analysis of the TRIGA Mark-II benchmark IEU-COMP-THERM-003 with Monte Carlo code MVP

    International Nuclear Information System (INIS)

    Mahmood, Mohammad Sayem; Nagaya, Yasunobu; Mori, Takamasa

    2004-03-01

    The benchmark experiments of the TRIGA Mark-II reactor in the ICSBEP handbook have been analyzed with the Monte Carlo code MVP using the cross section libraries based on JENDL-3.3, JENDL-3.2 and ENDF/B-VI.8. The MCNP calculations have been also performed with the ENDF/B-VI.6 library for comparison between the MVP and MCNP results. For both cores labeled 132 and 133, which have different core configurations, the ratio of the calculated to the experimental results (C/E) for k eff obtained by the MVP code is 0.999 for JENDL-3.3, 1.003 for JENDL-3.2, and 0.998 for ENDF/B-VI.8. For the MCNP code, the C/E values are 0.998 for both Core 132 and 133. All the calculated results agree with the reference values within the experimental uncertainties. The results obtained by MVP with ENDF/B-VI.8 and MCNP with ENDF/B-VI.6 differ only by 0.02% for Core 132, and by 0.01% for Core 133. (author)

  2. Characterization of typical irradiation channels of CNESTEN'S TRIGA Mark II reactor (Rabat, Morocco) using NAA K0-method

    International Nuclear Information System (INIS)

    Embarch, K.; Bounouira, H.; Bounakhla, M.; Amsil, H.; Jacimovic, R.

    2010-01-01

    The aim of this work is the use of neutron activation analysis using k0-standardization method to characterize some typical irradiation channels of the Moroccan TRIGA Mark II research reactor. The two parameters of neutron flux in the selected irradiation channels used for elemental concentration calculation, f (thermal-to-epithermal ratio) and α (deviation from the 1/E distribution), have been determined as well in the pneumatic tube (PT) as in the carousel facility (CR1) using the zirconium bare triple method. Results obtained for f and α in two irradiation channels show that f parameter determined in this way is different in the carousel facility (CR1) and the PT channel. This can be explained by the fact that the CR1 channel is situated in a graphite reflector and is relatively far from the reactor core, while the PT is in the core. Parameter α in the CR1 has a positive value, as expected, indicating that the neutron spectrum is relatively well thermalized. Parameter α in the PT has a negative value, which is very small and cannot significantly influence the final results obtained by k0-method. The method in our laboratory is validated by analyzing the elemental concentrations of the IAEA Standard Reference Material (Soil-7). All calculations were performed using Kay Win Software. (author)

  3. Characterization of the irradiation facilities SINCA and SIRCA of the TRIGA Mark III reactor using the code MCNPX

    International Nuclear Information System (INIS)

    Delfin L, A.; Garcia M, T.; Lucatero, M. A.; Cruz G, H. S.; Gonzalez, J. A.; Vargas E, S.

    2011-11-01

    The commitment of changing fuels of high enrichment for fuels of low enrichment in the TRIGA Mark III reactor of the Nuclear Center of Mexico generates the necessity to know the distribution of the spectrum of the neutrons flux in the irradiation facilities like they are: the Pneumatic System of Capsules Irradiation and the Rotational System of Capsules Irradiation. Is very important for the experiments design as well as for the reactor safety to know the profiles of the neutrons flux and the spectrum that these maintain with the mixed core with which operates, to effect of conserving the same characteristics when the reactor core will be operated with fuel of low enrichment totally. Also, knowing the profiles of the neutrons flux, the reactor operators can optimize the irradiation conditions of the processed samples and likewise the users can select the irradiation positions more adaptable to their necessities. This work present the characterization of the neutron flux in the irradiation facilities SINCA and SIFCA, calculated with the code MCNPX. (Author)

  4. Inspection with non destructive assay techniques of the aluminium coating of the TRIGA Mark III reactor vat

    International Nuclear Information System (INIS)

    Reyes A, A.I.; Gonzalez M, A.; Castaneda J, G.; Rivera M, H.; Sandoval G, I.

    2001-01-01

    In June 2000, the Reactor Department assigned to the Scientific Research Direction of the National Institute of Nuclear Research requested to the Non-destructive Assays Laboratory (LEND), assigned to the Materials Science Management, the inspection and measurement of thickness of the aluminium coating (liner) of the TRIGA Mark III reactor vat with non-destructive assay techniques, due to that the aluminium coating is exposed mainly to undergo slimming on its back side due to corrosion phenomena. Activity that was able to be carried out from april until august 2001. It is worth pointing out that this type of inspection with these techniques was realized by first time. The non-destructive assays (NDA) are techniques which use indirect physical methods for inspecting the sanitation of components in process or in service, for detect lack of continuity or defects which affect their quality or usefulness. The application of those do not alter the physical, chemical, mechanical or dimensional properties of the part subject of inspection. The results of the application of the ultrasound inspection techniques, industrial radiography and penetrating liquids are presented. (Author)

  5. Research work with TRIGA Mark II at the Nuclear Chemistry Section of the 'J. Stefan' Institute in Ljubljana

    International Nuclear Information System (INIS)

    Byrne, A.R.; Dermelj, M.; Kosta, L.; Ravkin, V.; Stegnar, P.

    1978-01-01

    The general features of our research programme using TRIGA MK II, as outlined at the last TRIGA Reactor Users Conference in Vienna, September 28-30,1976, remain the same; namely, neutron activation analysis for trace and some minor elements. The four main areas presently investigated are a) environmental studies, b) life sciences research, c) standardization and d) methodology for specific problems arising in the first three topics

  6. Determination of the energy spectrum of the neutrons in the central thimble of the reactor core TRIGA Mark III; Determinacion del espectro de energia de los neutrones en el dedal central del nucleo del reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Parra M, M. A.

    2014-07-01

    This thesis presents the neutron spectrum measurements inside the core of the TRIGA Mark III reactor at 1 MW power in steady-state, with the bridge placed in the center of the swimming pool, using several metallic threshold foils. The activation detectors are inserted in the Central Thimble of the reactor core, all the foils are irradiated in the same position and irradiation conditions (one by one). The threshold detectors are made of different materials such as: Au{sup 197}, Ni{sup 58}, In{sup 115}, Mg{sup 24}, Al{sup 27}, Fe{sup 58}, Co{sup 59} and Cu{sup 63}, they were selected to cover the full range the energies (10{sup -10} to 20 MeV) of the neutron spectrum in the reactor core. After the irradiation, the activation detectors were measured by means of spectrometry gamma, using a high resolution counting system with a hyper pure Germanium crystal, in order to obtain the saturation activity per target nuclide. The saturation activity is one of the main input data together with the initial spectrum, for the computational code SANDBP (hungarian version of the code SAND-II), which through an iterative adjustment, gives the calculated spectrum. The different saturation activities are necessary for the unfolding method, used by the computational code SANDBP. This research work is very important, since the knowledge of the energetic and spatial distribution of the neutron flux in the irradiation facilities, allows to characterize properly the irradiation facilities, just like, to estimate with a good precision various physics parameters of the reactor such as: neutron fluxes (thermal, intermediate and fast), neutronic dose, neutron activation analysis (NAA), spectral indices (cadmium ratio), buckling, fuel burnup, safety parameters (reactivity, temperature distribution, peak factors). In addition, the knowledge of the already mentioned parameters can give a best use of reactor, optimizing the irradiations requested by the users for their production process or

  7. Determination of the flows profile in the role of power in the central thimble of TRIGA Mark III Reactor; Determinacion del perfil de flujos en funcion de la potencia en el dedal central del Reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Garcia F, A.

    2010-07-01

    The overall objective of the thesis project is to determine the flow profiles sub cadmic and epi cadmic in the central thimble to different powers and operation times of TRIGA Mark III Reactor, using activation foils as detectors. In the reactor operation, it is necessary to know the neutron flow profile for to realize other tasks as: the radioisotopes production, research in reactors physics and fuel burning. The distribution of the neutron flow, accurately reflects what is happening in the reactor core, plus the flows value in this distribution is directly related to the power generated. For this reason it is performed the sub cadmic flow measurement with energies between 0 and 0.4 eV (energy of the cadmium cut E{sub cd} approx 0.4 eV) and epi cadmic flow with energies greater than 0.4 eV, in the central thimble powers to the powers of 10, 100 W, 1, 10 100 Kw and 1 MW. The method used is known as flakes activation, which is to be arranged by placing flakes ( 3 mm of diameter and 0.0508 mm of thickness) of a given material (either Au, In, Cu, Mn, etc.) into an aluminum tube outside diameter equal to 6.35 mm, alternating flakes with lids covered and discovered of cadmium (3.4 mm of diameter and 0.508 mm of thickness) and separated by lucite pieces of 3 mm of diameter and 25.4 mm in length. After irradiating the flakes for some time, is measured the gamma activity of each of them, using a hyper pure germanium detector of high resolution. Already known gamma activity, proceed to calculate the epi cadmic and sub cadmic flows using a computer program in Fortran language, called Caflu. (Author)

  8. Elaboration of the configuration and programming of the interlocks system of the TRIGA Mark III reactor; Elaboracion de la configuracion y programacion del sistema de interbloqueos del reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Mejia C, M. A.

    2016-07-01

    The modernization of the TRIGA Mark III reactor interlock system requires a system that provides high reliability, flexibility and ease of operation during reactor operation. With this modernization of the system, is intended to prevent, control and mitigate the causes of probable accidents reported in the reactor accident analysis. On the other hand, is foreseen the ease reactor operation in a simple, safe and efficient way. The programmable logic controller can be programmed by programming instructions using simple language and easy to develop, these can be modified from a computer using the programming software. In addition, another of the advantages offered by the controller is that can be modified from a touch screen (human-machine interface) that allows adjustment, without the need to use programming software and diagnostic functions during the process. As a result of the present work, a situation of improvement in the reactor operation was generated, facilitating the handling of the bridge and increasing the efficiency of the system in the execution of the operating conditions of the installations external to the reactor. A modern, more reliable and much less expensive system was achieved than the previous one, avoiding that the maintenance to the system generates high expenses. With respect to the development of the application programming, a control was implemented that allows to select a zone of the five that have inside the pool to carry out the displacement of automatic way and later to be located in that zone, having in this way a greater efficiency and ease in bridge control. (Author)

  9. Operating experience and maintenance at the TRIGA Mark II LENA reactor

    International Nuclear Information System (INIS)

    Cingoli, F.; Altieri, S.; Lana, F.; Rosti, G.; Alloni, L.; Meloni, S.

    1988-01-01

    The last two years at the Trigs Mark II LENA plant were characterized by the running of the n-n-bar oscillation NADIR experiment. Consequently reactor operation was positively affected and the running hours rose again above 1000 hours per year. The LENA team was also deeply involved in the procedures for the renewal of the reactor operation license. The new requirements set by the Nuclear Energy Licensing Authority (ENEA for Italy) most of which concerning radiation protection and environmental impact, have been already fulfilled. In some cases the installation of new apparatus is underway

  10. 41Ar-concentration measurements at the Finnish TRIGA Mark II

    International Nuclear Information System (INIS)

    Tamminen, A.

    1970-01-01

    41 Ar-concentrations in the reactor hall and in the Ar-ventilation duct of FiR-1 (IRIGA Mark II, 250 kW) have been measured during normal operation conditions. Additional measurements have been performed varying Ar-ventilation and hall ventilation flow. A γ- and background compensated thin window proportional detector and a β-Geiger detector for 41 Ar-measurements are described. The hall concentration has also been estimated from background measurements with an unshielded Ge(Li)-detector. The saturation concentration in the reactor hall with and without the hall ventilation is about 1 x 10 -7 μCi/cm 3 and 3 x 10 -7 μCi/cm 3 , respectively. (author)

  11. Determination of the flows profile in the role of power in the central thimble of TRIGA Mark III Reactor

    International Nuclear Information System (INIS)

    Garcia F, A.

    2010-01-01

    The overall objective of the thesis project is to determine the flow profiles sub cadmic and epi cadmic in the central thimble to different powers and operation times of TRIGA Mark III Reactor, using activation foils as detectors. In the reactor operation, it is necessary to know the neutron flow profile for to realize other tasks as: the radioisotopes production, research in reactors physics and fuel burning. The distribution of the neutron flow, accurately reflects what is happening in the reactor core, plus the flows value in this distribution is directly related to the power generated. For this reason it is performed the sub cadmic flow measurement with energies between 0 and 0.4 eV (energy of the cadmium cut E cd ∼ 0.4 eV) and epi cadmic flow with energies greater than 0.4 eV, in the central thimble powers to the powers of 10, 100 W, 1, 10 100 Kw and 1 MW. The method used is known as flakes activation, which is to be arranged by placing flakes ( 3 mm of diameter and 0.0508 mm of thickness) of a given material (either Au, In, Cu, Mn, etc.) into an aluminum tube outside diameter equal to 6.35 mm, alternating flakes with lids covered and discovered of cadmium (3.4 mm of diameter and 0.508 mm of thickness) and separated by lucite pieces of 3 mm of diameter and 25.4 mm in length. After irradiating the flakes for some time, is measured the gamma activity of each of them, using a hyper pure germanium detector of high resolution. Already known gamma activity, proceed to calculate the epi cadmic and sub cadmic flows using a computer program in Fortran language, called Caflu. (Author)

  12. A high performance neutron powder diffractometer at 3 MW Triga Mark-II research reactor in Bangladesh

    Energy Technology Data Exchange (ETDEWEB)

    Kamal, I., E-mail: imtiaz-kamal26@yahoo.com; Yunus, S. M., E-mail: yunussm11@yahoo.com; Datta, T. K., E-mail: tk-datta4@yahoo.com; Zakaria, A. K. M.; Das, A. K.; Aktar, S.; Hossain, S. [Institute of Nuclear Science and Technology, Atomic Energy Research Establishment, Ganakbari, Savar, Dhaka (Bangladesh); Berliner, R., E-mail: RB@instrumentationAssociates.com [Instrumentation Associates, Durham, North Carolina (United States); Yelon, W. B., E-mail: yelonwb@hotmail.com [Oak Ridge National Laboratory, Oak Ridge, Tennessee (United States)

    2016-07-12

    A high performance neutron diffractometer called Savar Neutron Diffractometer (SAND) was built and installed at radial beam port-2 of TRIGA Mark II research reactor at AERE, Savar, Dhaka, Bangladesh. Structural studies of materials are being done by this technique to characterize materials crystallograpohically and magnetically. The micro-structural information obtainable by neutron scattering method is very essential for determining its technological applications. This technique is unique for understanding the magnetic behavior in magnetic materials. Ceramic, steel, electronic and electric industries can be benefited from this facility for improving their products and fabrication process. This instrument consists of a Popovicimonochromator with a large linear position sensitive detector array. The monochromator consists of nine blades of perfect single crystal of silicon with 6 mm thickness each. The monochromator design was optimized to provide maximum flux on 3 mm diameter cylindrical sample with a relatively flat angular dependence of resolution. Five different wave lengths can be selected by orienting the crystal at various angles. A sapphire filter was used before the primary collimator to minimize the first neutron. The detector assembly is composed of 15 linear position sensitive proportional counters placed at either 1.1 m or 1.6 m from the sample position and enclosed in a air pad supported high density polythene shield. Position sensing is obtained by charge division using 1-wide NIM position encoding modules (PEM). The PEMs communicate with the host computer via USB. The detector when placed at 1.1 m, subtends 30° (2θ) at each step and covers 120° in 4 steps. When the detector is placed at 1.6 m it subtends 20° at each step and covers 120° in 6 steps. The instrument supports both low and high temperature sample environment. The instrument supports both low and high temperature sample environment. The diffractometer is a state-of-the art technology

  13. Determination of the energy spectrum of the neutrons in the central thimble of the reactor core TRIGA Mark III

    International Nuclear Information System (INIS)

    Parra M, M. A.

    2014-01-01

    This thesis presents the neutron spectrum measurements inside the core of the TRIGA Mark III reactor at 1 MW power in steady-state, with the bridge placed in the center of the swimming pool, using several metallic threshold foils. The activation detectors are inserted in the Central Thimble of the reactor core, all the foils are irradiated in the same position and irradiation conditions (one by one). The threshold detectors are made of different materials such as: Au 197 , Ni 58 , In 115 , Mg 24 , Al 27 , Fe 58 , Co 59 and Cu 63 , they were selected to cover the full range the energies (10 -10 to 20 MeV) of the neutron spectrum in the reactor core. After the irradiation, the activation detectors were measured by means of spectrometry gamma, using a high resolution counting system with a hyper pure Germanium crystal, in order to obtain the saturation activity per target nuclide. The saturation activity is one of the main input data together with the initial spectrum, for the computational code SANDBP (hungarian version of the code SAND-II), which through an iterative adjustment, gives the calculated spectrum. The different saturation activities are necessary for the unfolding method, used by the computational code SANDBP. This research work is very important, since the knowledge of the energetic and spatial distribution of the neutron flux in the irradiation facilities, allows to characterize properly the irradiation facilities, just like, to estimate with a good precision various physics parameters of the reactor such as: neutron fluxes (thermal, intermediate and fast), neutronic dose, neutron activation analysis (NAA), spectral indices (cadmium ratio), buckling, fuel burnup, safety parameters (reactivity, temperature distribution, peak factors). In addition, the knowledge of the already mentioned parameters can give a best use of reactor, optimizing the irradiations requested by the users for their production process or research projects. (Author)

  14. Preliminary investigations of a mixed standard-flip core for a TRIGA Mark II

    International Nuclear Information System (INIS)

    Ringle, John C.; Johnson, A.G.; Anderson, T.V.

    1974-01-01

    Several years ago it became apparent that due to our rapidly- increasing use rate, we would need a substantial amount of new fuel by late 1974 or early 1975. After investigations and discussions with GA, we decided that FLIP fuel would best meet our requirements for maximum fuel economy and high peak pulsing power. A proposal was submitted to the AEC for fuel assistance, and late in 1973 we were awarded a grant of $61,875. This will allow us to buy 3 FLIP-fueled-follower control rods, 1 instrumented FLIP fuel element, and 26 standard FLIP elements, giving us then a mixed core of approximately one-third FLIP and two-thirds standard elements. License amendments to accommodate this change are rather straightforward; modifications to the Technical Specifications will be somewhat more involved. The largest revisions which we envision are to our Safety Analysis Report. Although a few reactors have operated with a full FLIP core, and a few others have converted to mixed standard-FLIP cores, none of these has a standard Mark II core configuration. Those who have already converted to a mixed core have data and calculations which may be helpful to us, but the extent to which we can use these remains to be seen. The present status of our investigations into the analysis of a mixed standard-FLIP core will be presented. Any problems in calculational methods, finding appropriate data, modifications to Technical Specifications, etc., will be identified, and suggestions and help in these areas will be welcomed. (author)

  15. Preliminary investigations of a mixed standard-flip core for a TRIGA Mark II

    Energy Technology Data Exchange (ETDEWEB)

    Ringle, John C; Johnson, A G; Anderson, T V [Oregon State University (United States)

    1974-07-01

    Several years ago it became apparent that due to our rapidly- increasing use rate, we would need a substantial amount of new fuel by late 1974 or early 1975. After investigations and discussions with GA, we decided that FLIP fuel would best meet our requirements for maximum fuel economy and high peak pulsing power. A proposal was submitted to the AEC for fuel assistance, and late in 1973 we were awarded a grant of $61,875. This will allow us to buy 3 FLIP-fueled-follower control rods, 1 instrumented FLIP fuel element, and 26 standard FLIP elements, giving us then a mixed core of approximately one-third FLIP and two-thirds standard elements. License amendments to accommodate this change are rather straightforward; modifications to the Technical Specifications will be somewhat more involved. The largest revisions which we envision are to our Safety Analysis Report. Although a few reactors have operated with a full FLIP core, and a few others have converted to mixed standard-FLIP cores, none of these has a standard Mark II core configuration. Those who have already converted to a mixed core have data and calculations which may be helpful to us, but the extent to which we can use these remains to be seen. The present status of our investigations into the analysis of a mixed standard-FLIP core will be presented. Any problems in calculational methods, finding appropriate data, modifications to Technical Specifications, etc., will be identified, and suggestions and help in these areas will be welcomed. (author)

  16. Criticality and safety parameter studies for upgrading 3 MW TRIGA MARK II research reactor and validation of generated cross section library and computational method

    International Nuclear Information System (INIS)

    Bhuiyan, S.I.; Mondal, M.A.W.; Sarker, M.M.; Rahman, M.; Shahdatullah, M.S.; Huda, M.Q.; Chakrroborty, T.K.; Khan, M.J.H.

    2000-01-01

    This study deals with the neutronic and thermal hydraulic analysis of the 3MW TRIGA MARK II research reactor to upgrade it to a higher flux. The upgrading will need a major reshuffling and reconfiguration of the current core. To reshuffle the current core configuration, the chain of NJOY94.10 - WIMSD-5A - CITATION - PARET - MCNP4B2 codes has been used for the overall analysis. The computational methods, tools and techniques, customisation of cross section libraries, various models for cells and super cells, and a lot of associated utilities have been standardised and established/validated for the overall core analysis. Analyses using the 4-group and 7-group libraries of macroscopic cross sections generated from the 69-group WIMSD-5 library showed that a 7-group structure is more suitable for TRIGA calculations considering its LEU fuel composition. The MCNP calculations established that the CITATION calculations and the generated cross section library are reasonably good for neutronic analysis of TRIGA reactors. Results obtained from PARET demonstrated that the flux upgrade will not cause the temperature limit on the fuel to be exceeded. Also, the maximum power density remains, by a substantial margin below the level at which the departure from nucleate boiling could occur. A possible core with two additional irradiation channels around the CT is projected where almost identical thermal fluxes as in the CT are obtained. The reconfigured core also shows 7.25% thermal flux increase in the Lazy Susan. (author)

  17. Experience in operation and maintenance of the TRIGA Mark II reactor at the University of Pavia in the time period July 1974 - June 1976

    International Nuclear Information System (INIS)

    Cambieri, A.; Cingoli, F.; Genova, N.; Meloni, S.; Perlini, G.

    1976-01-01

    The operation of the 250 kW steady state/250 MW pulsed TRIGA Mark II Reactor of the University of Pavia over the past two years is presented and discussed. Reactor maintenance activity is presented as well. Data for reactor utilization and a summary of the health physics procedures are also given. Since the third European Conference of TRIGA Reactor Users in 1974, reactor operation took place smoothly without major troubles. Because of the core excess decrease due to reactor operation and consequent burn-up, ten new stainless steel clad fuel elements were bought from General Atomic. Reactor operation license expired at the end of 1975 and it is now under way the bureaucratic work to get its renewal. The aging of the electronic equipment raises minor problems and the predicted switching to a new solid state equipment started by changing the old electromechanical rod position indicators with new digital ones. The installation of the Euracos II facility (Enriched Uranium Converter Source), described at the last TRIGA Users Conference, began at the end of 1975 and it is still under way. The first operation of the facility will take place at reduced power so that the removal of the graphite blocks from thermal column was not accomplished. The installation of the facility is described and the procedures of its operation in connection with reactor operation are presented as well. (author)

  18. Improved measurements of thermal power and control rods using multiple detectors at the TRIGA Mark II reactor in Ljubljana

    International Nuclear Information System (INIS)

    Zerovnik Gasper; Snoj Luka; Trkov Andrej; Barbot Loic; Fourmentel Damien; Villard Jean-Francois

    2013-06-01

    The aim of the current bilateral project between CEA Cadarache and JSI is to improve the accuracy of the online thermal power monitoring at the JSI TRIGA reactor. Simultaneously, a new wide range multichannel acquisition system for fission chambers, recently developed by CEA, is tested. In the paper, calculational and experimental power calibration methods are described. The focus is on use of multiple detectors in combination with pre-calculated and pre-measured control rod- position-dependent correction factors to improve the reactor power reading. The system will be implemented and tested at the JSI TRIGA reactor in 2014. (authors)

  19. Behavior of exposed human lymphocytes to a neutron beam of the reactor TRIGA Mark III; Comportamiento de linfocitos humanos expuestos a un haz de neutrones del reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Carbajal R, M. I.

    2012-07-01

    Excessive exposure to ionizing radiation occurs in people who require radiation treatment, also in those for work can come to receive doses above the permitted levels. A third possibility of exposure is the release of radioactive material in which the general population is affected. Most of the time the exhibition is partial and only rarely occurs throughout the body. For various reasons, situations arise where it is impossible to determine by conventional physical methods, the amount of radiation you were exposed to the affected person and in these cases where the option to follow is the Biological Dosimetry, where the analysis of chromosomes dicentrics is used to estimate the dose of ionizing radiation exposure. A calibration curve is generated from in vitro analysis of dicentric chromosome, which are found in human lymphocytes, treated with different types and doses of radiation. The dicentric is formed from two lesions, one on each chromosome and their union results in a structure having two centromeres, acentric fragment with her for the union of several chromosomes leads to more complex structures as tri-centric s, tetra or penta-centric s, which have the same origin. The dose-response curve is estimated by observing the frequency of dicentrics and extrapolated to a dose-effect curve previously established, for which it is necessary that each lab has its own calibration curves, taking into account that for a Let low radiation, dose-effect curve follows a linear-quadratic model Y=C + {alpha}D + {beta}D. The production of dicentric chromosomes with a high Let, was studied using a beam of neutrons generated in the reactor TRIGA Mark III with an average energy of 1 MeV, adjusting the linear model Y={alpha}D. The dose-response relationship is established in blood samples from the same donor, the coefficient {alpha} of the dose-response is Y = (0.3692 {+-} 0.011 * D), also shows that saturation is reached in system 4 Gy. (Author)

  20. Criticality and shielding calculations for containers in dry of spent fuel of TRIGA Mark III reactor of ININ; Calculos de criticidad y blindaje para contenedores en seco de combustible gastado del reactor Triga Mark III del ININ

    Energy Technology Data Exchange (ETDEWEB)

    Barranco R, F.

    2015-07-01

    In this thesis criticality and shielding calculations to evaluate the design of a container of dry storage of spent nuclear fuel generated in research reactors were made. The design of such container was originally proposed by Argentina and Brazil, and the Instituto Nacional de Investigaciones Nucleares (ININ) of Mexico. Additionally, it is proposed to modify the design of this container to store spent fuel 120 that are currently in the pool of TRIGA Mark III reactor, the Nuclear Center of Mexico and calculations and analyzes are made to verify that the settlement of these fuel elements is subcritical limits and dose rates to workers and the general public are not exceeded. These calculations are part of the design criteria for security protection systems in dry storage system (Dss for its acronym in English) proposed by the Nuclear Regulatory Commission (NRC) of the United States. To carry out these calculations simulation codes of Monte Carlo particle transport as MCNPX and MCNP5 were used. The initial design (design 1) 78 intended to store spent fuel with a maximum of 115. The ININ has 120 fuel elements and spent 3 control rods (currently stored in the reactor pool). This leads to the construction of two containers of the original design, but for economic reasons was decided to modify (design 2) to store in a single container. Criticality calculations are performed to 78, 115 and fresh fuel elements 124 within the container, to the two arrangements described in Chapter 4, modeling the three-dimensional geometry assuming normal operating conditions and accident. These calculations are focused to demonstrate that the container will remain subcritical, that is, that the effective multiplication factor is less than 1, in particular not greater than 0.95 (as per specified by the NRC). Spent fuel 78 and 124 within the container, both gamma radiation to neutron shielding calculations for only two cases were simulated. First actinides and fission products generated

  1. Simulator of the punctual kinetics of a TRIGA Mark III reactor with power diffuse control in a visual environment; Simulador de la cinetica puntual de un reactor nuclear TRIGA Mark III con control difuso de potencia en un ambiente visual

    Energy Technology Data Exchange (ETDEWEB)

    Perez M, C

    2004-07-01

    The development of a software is presented that simulates the punctual kinetics of a nuclear reactor of investigation model TRIGA Mark III, generating the answers of the reactor low different algorithms of control of power. The user requires a graphic interface that allows him easily interacting with the simulator. To achieve the proposed objective, first the system was modeled in open loop, not using a mathematical model of the consistent reactor in a system of linear ordinary differential equations. For their solution in real time the numeric method of Runge-Kutta-Fehlberg was used. As second phase, it was modeled to the system in closed loop, using for it an algorithm of control of the power based on fuzzy logic. This software has as purpose to help the investigator in the control area who will be able to prove different algorithms for the control of the power of the reactor. This is achieved using the code source in language C, C++, Visual Basic, with which a file is generated. DLL and it is inserted in the simulator. Then they will be able to visualize the results as if their controller had installed in the reactor, analyzing the behavior of all his variables that will be stored in files, for his later study. The easiness of proving these control algorithms in the reactor without necessity to make it physically has important consequences as the saving in the expense of fuel, the not generation of radioactive waste and the most important thing, one doesn't run any risk. The simulator can be used how many times it is necessary until the total purification of the algorithm. This program is the base for following investigation processes, enlarging the capacities and options of the same one. The program fulfills the time of execution satisfactorily, assisting to the necessity of visualizing the behavior in real time of the reactor, and it responds from an effective way to the petitions of changes of power on the part of the user. (Author)

  2. Larger research programs at the beam holes of the Austrian TRIGA Mark II reactor. Design and construction of a Fourier chopper-selector at the Austrian TRIGA reactor

    International Nuclear Information System (INIS)

    Fleck, C.M.

    1970-01-01

    A neutron chopping system utilizing Fourier analysis has great advantages to alternative systems. For this purpose the chopper consists of a disc, opaque to neutrons, rotating on an axis perpendicular to its centre. Around its outside edge a series of uniformly spaced teeth and spaces are formed with neutron transparent gaps extending towards the centre. By using a stationary section having the same pattern of teeth and gaps it is possible to utilize a beam area considerably larger than the area of one tooth. During the last years at the TRIGA Reactor in Vienna a neutron chopping-and selecting-system is developed and in construction, which will not only chop the beam in that way necessary for Fourier analysis but also select the energy. The selection is done by seven discs of the form described above mounted on an axis. The selector is designed for neutron wave lengths between 3 and 30 A. The resolution is constant over the whole range of energy and depends on the beam divergence. Thus the modulation frequency is 10 4 sec -1 and the half-width of the neutron pulse about 50 μsec

  3. Simulator of the punctual kinetics of a TRIGA Mark III reactor with power diffuse control in a visual environment

    International Nuclear Information System (INIS)

    Perez M, C.

    2004-01-01

    The development of a software is presented that simulates the punctual kinetics of a nuclear reactor of investigation model TRIGA Mark III, generating the answers of the reactor low different algorithms of control of power. The user requires a graphic interface that allows him easily interacting with the simulator. To achieve the proposed objective, first the system was modeled in open loop, not using a mathematical model of the consistent reactor in a system of linear ordinary differential equations. For their solution in real time the numeric method of Runge-Kutta-Fehlberg was used. As second phase, it was modeled to the system in closed loop, using for it an algorithm of control of the power based on fuzzy logic. This software has as purpose to help the investigator in the control area who will be able to prove different algorithms for the control of the power of the reactor. This is achieved using the code source in language C, C++, Visual Basic, with which a file is generated. DLL and it is inserted in the simulator. Then they will be able to visualize the results as if their controller had installed in the reactor, analyzing the behavior of all his variables that will be stored in files, for his later study. The easiness of proving these control algorithms in the reactor without necessity to make it physically has important consequences as the saving in the expense of fuel, the not generation of radioactive waste and the most important thing, one doesn't run any risk. The simulator can be used how many times it is necessary until the total purification of the algorithm. This program is the base for following investigation processes, enlarging the capacities and options of the same one. The program fulfills the time of execution satisfactorily, assisting to the necessity of visualizing the behavior in real time of the reactor, and it responds from an effective way to the petitions of changes of power on the part of the user. (Author)

  4. Criticality and shielding calculations for containers in dry of spent fuel of TRIGA Mark III reactor of ININ

    International Nuclear Information System (INIS)

    Barranco R, F.

    2015-01-01

    In this thesis criticality and shielding calculations to evaluate the design of a container of dry storage of spent nuclear fuel generated in research reactors were made. The design of such container was originally proposed by Argentina and Brazil, and the Instituto Nacional de Investigaciones Nucleares (ININ) of Mexico. Additionally, it is proposed to modify the design of this container to store spent fuel 120 that are currently in the pool of TRIGA Mark III reactor, the Nuclear Center of Mexico and calculations and analyzes are made to verify that the settlement of these fuel elements is subcritical limits and dose rates to workers and the general public are not exceeded. These calculations are part of the design criteria for security protection systems in dry storage system (Dss for its acronym in English) proposed by the Nuclear Regulatory Commission (NRC) of the United States. To carry out these calculations simulation codes of Monte Carlo particle transport as MCNPX and MCNP5 were used. The initial design (design 1) 78 intended to store spent fuel with a maximum of 115. The ININ has 120 fuel elements and spent 3 control rods (currently stored in the reactor pool). This leads to the construction of two containers of the original design, but for economic reasons was decided to modify (design 2) to store in a single container. Criticality calculations are performed to 78, 115 and fresh fuel elements 124 within the container, to the two arrangements described in Chapter 4, modeling the three-dimensional geometry assuming normal operating conditions and accident. These calculations are focused to demonstrate that the container will remain subcritical, that is, that the effective multiplication factor is less than 1, in particular not greater than 0.95 (as per specified by the NRC). Spent fuel 78 and 124 within the container, both gamma radiation to neutron shielding calculations for only two cases were simulated. First actinides and fission products generated

  5. Development of a simulator for design and test of power controllers in a TRIGA Mark III reactor; Desarrollo de un simulador para diseno y prueba de controladores de potencia en un reactor TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Perez M, C.; Benitez R, J.S.; Lopez C, R. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2003-07-01

    The development of a simulator that uses the Runge-Kutta-Fehlberg method to solve the model of the punctual kinetics of a nuclear research reactor type TRIGA. The simulator includes an algorithm of power control of the reactor based on the fuzzy logic, a friendly graphic interface which responds to the different user's petitions and that it shows numerical and graphically the results in real time. The user can modify the demanded power and to visualize the dynamic behavior of the one system. This simulator was developed in Visual Basic under an open architecture with which its will be prove different controllers for its analysis. (Author)

  6. Operating experiences and utilization programmes of the BAEC 3 MW TRIGA Mark-II research reactor of Bangladesh

    International Nuclear Information System (INIS)

    Haque, M.M.; Soner, M.A.M.; Saha, P.K.; Salam, M.A.; Zulquarnain, M.A.

    2008-01-01

    The 3 MW TRIGA Mark-II research reactor of Bangladesh Atomic Energy Commission (BAEC) has been operating since September 14, 1986. The reactor is used for radioisotope production ( 131 I, 99m Tc, 46 Sc), various R and D activities, manpower training and education. The reactor has been operated successfully since its commissioning with the exception of a few reportable incidents. Of these, the decay tank leakage incident of 1997 is considered to be the most significant one. As a result of this incident, reactor operation at full power remained suspended for about 4 years. However, the reactor operation was continued during this period at a power level of 250 kW to cater the needs of various R and D groups, which required lower neutron flux for their experiments. This was made possible by establishing a temporary by pass connection across the decay tank using local technology. The reactor was made operational again at full power after successful replacement of the damaged decay tank in August 2001. At that time, several modifications of the reactor cooling system along with its associated structures were also implemented and then necessary testing and commissioning of the newly installed component/equipment were carried out. The other incident was the contamination of the Dry Central Thimble (DCT) that took place in March 2002 when a pyrex vial containing 50g of TeO 2 powder got melted inside the DCT. The vial was melted due to high heat generation on its surface while the reactor was operated for 8 hours at 3 MW for trial production of Iodine-131 ( 131 I). A Wet Central Thimble (WCT) was used to replace the damaged DCT in June 2002 such that the reactor operation could be resumed. The WCT was again replaced by a new DCT in June 2003 such that radioisotope production could be continued. The facility has so far been used to train up a total of 27 personnel including several foreign nationals to the level of Senior Reactor Operator (SRO) and Reactor Operator (RO). The

  7. Obtaining of total and thermal neutron flux in the carousel facility of the TRIGA MARK IPR-R1 reactor using the Monte Carlo transport method

    International Nuclear Information System (INIS)

    Guerra, Bruno Teixeira

    2011-01-01

    The IPR-R1 is a reactor type TRIGA, Mark-I model, manufactured by the General Atomic Company and installed at Nuclear Technology Development Centre (CDTN) of Brazilian Nuclear Energy Commission (CNEN), in Belo Horizonte, Brazil. It is a light water moderated and cooled, graphite-reflected, open-pool type research reactor. IPR-R1 works at 100 kW but it will be briefly licensed to operate at 250 kW. It presents low power, low pressure, for application in research, training and radioisotopes production. The fuel is an alloy of zirconium hydride and uranium enriched at 20% in 235 U. The goal this work is modelling of the IPR-R1 Research Reactor TRIGA using the codes MCNPX2.6.0 (Monte Carlo N-Particle Transport extend) and MCNP5 to the calculating the neutron flux in the carousel facility. In each simulation the sample was placed in a different position, totaling forty positions around of the reactor core. The comparison between the results obtained with experimental values from other work showing a relatively good agreement. Moreover, this methodology is a theoretical tool in validating of the experimental values and necessary for determining neutron flux which can not be accessible experimentally. (author)

  8. Comparative Study of some Parameters reported in the Safety Analysis Report of TRIGA MARK II Research reactor with Calculations

    International Nuclear Information System (INIS)

    Chakrobortty, T.K.; Huda, M.Q.; Bhuiyan, S.I.; Mondal, M.A.W.

    1997-06-01

    An attempt has been made to investigate some of the parametric results reported in the safety Analysis Report (SAR) with the theoretical analysis carried out by different computer codes and data bases. Different neutronics, thermal hydraulics and safety parameters such as core criticality and burnup lifetime, power peaking factor, prompt negative temperature coefficient, neutron flux, pulse characteristics, steady state and transient behaviors of the TRIGA reactor were analyzed. The investigated results were found to be in fairly good agreement with the values reported in the SAR. 12 refs., 14 figs., 1 table (Author)

  9. Development of a simulator for design and test of power controllers in a TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Perez M, C.; Benitez R, J.S.; Lopez C, R.

    2003-01-01

    The development of a simulator that uses the Runge-Kutta-Fehlberg method to solve the model of the punctual kinetics of a nuclear research reactor type TRIGA. The simulator includes an algorithm of power control of the reactor based on the fuzzy logic, a friendly graphic interface which responds to the different user's petitions and that it shows numerical and graphically the results in real time. The user can modify the demanded power and to visualize the dynamic behavior of the one system. This simulator was developed in Visual Basic under an open architecture with which its will be prove different controllers for its analysis. (Author)

  10. Measurement of the neutron activation constants Q0 and k0 for the 27Al(n, γ)28Al reaction at the JSI TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Vladimir Radulovic; Andrej Trkov; Radojko Jacimovic; Robert Jeraj

    2013-01-01

    Measurements of the neutron activation constants Q 0 and k 0 for the 27 Al(n, γ) 28 Al reaction have been performed in two irradiation channels with different spectral characteristics at the JSI TRIGA Mark II reactor. In the determination of Q 0 the fission spectrum contribution to the reaction rates has been corrected for. The final experimental value of the Q 0 factor was found to differ significantly from the adopted value in the k 0 -database. The experimental value of the k 0 factor is in agreement with the recommended value in the k 0 -database. The thermal cross-section and resonance integral for the reaction were found to be in good agreement with the values calculated from the cross-sections from the ENDF/B-VII.1 library. (author)

  11. Steady-state thermal-hydraulic analysis of the Moroccan TRIGA MARK II reactor by using PARET/ANL and COOLOD-N2 codes

    International Nuclear Information System (INIS)

    Boulaich, Y.; Nacir, B.; El Bardouni, T.; Zoubair, M.; El Bakkari, B.; Merroun, O.; El Younoussi, C.; Htet, A.; Boukhal, H.; Chakir, E.

    2011-01-01

    Research highlights: → The COOLOD/N2 and PARET/ANL codes were used for a steady-state thermal-hydraulic and safety analysis of the 2 MW TRIGA MARK II reactor located at the Nuclear Studies Center of Maamora (CENM), Morocco. → The main objective of this study is to ensure the safety margins of different safety related parameters by steady-state calculations at full power level (2 MW). → The most important conclusion is that all obtained values of DNBR, fuel center and surface temperature, cladding surface temperature and coolant temperature across the hottest channel are largely far to compromise safety of the reactor. - Abstract: The COOLOD/N2 and PARET/ANL codes were used for a steady-state thermal-hydraulic and safety analysis of the 2 MW TRIGA MARK II reactor located at the Nuclear Studies Center of Maamora (CENM), Morocco. In order to validate our PARET/ANL and COOLOD-N2 models, the fuel center temperature as function of core power was calculated and compared with the corresponding experimental values. The comparison indicates that the calculated values are in satisfactory agreement with the measurement. The main objective of this study is to ensure the safety margins of different safety related parameters by steady-state calculations at full power level (2 MW). Therefore, we have calculated the departure from nucleate boiling ratio (DNBR), fuel center and surface temperature, cladding surface temperature and coolant temperature profiles across the hottest channel. The most important conclusion is that all obtained values are largely far to compromise safety of the reactor.

  12. Characterization of the neutron flux in the Hohlraum of the thermal column of the TRIGA Mark III reactor of the ININ

    International Nuclear Information System (INIS)

    Delfin L, A.; Palacios, J.C.; Alonso, G.

    2006-01-01

    Knowing the magnitude of the neutron flux in the reactor irradiation facilities, is so much importance for the operation of the same one, like for the investigation developing. Particularly, knowing with certain precision the spectrum and the neutron flux in the different positions of irradiation of a reactor, it is essential for the evaluation of the results obtained for a certain irradiation experiment. The TRIGA Mark III reactor account with irradiation facilities designed to carry out experimentation, where the reactor is used like an intense neutron source and gamma radiation, what allows to make irradiations of samples or equipment in radiation fields with components and diverse levels in the different facilities, one of these irradiation facilities is the Thermal Column where the Hohlraum is. In this work it was carried out a characterization of the neutron flux inside the 'Hohlraum' of the irradiation facility Thermal Column of the TRIGA Mark III reactor of the Nuclear Center of Mexico to 1 MW of power. It was determined the sub cadmic neutron flux and the epi cadmic by means of the neutron activation technique of thin sheets of gold. The maps of the distribution of the neutron flux for both energy groups in three different positions inside the 'Hohlraum' are presented, these maps were obtained by means of the irradiation of undressed thin activation sheets of gold and covered with cadmium in arrangements of 10 x 12, located parallel to 11.5 cm, 40.5 cm and 70.5 cm to the internal wall of graphite of the installation in inverse address to the position of the reactor core. Starting from the obtained values of neutron flux it was found that, for the same position of the surface of irradiation of the experimental arrangement, the relative differences among the values of neutron flux can be of 80%, and that the differences among different positions of the irradiation surfaces can vary until in a one order of magnitude. (Author)

  13. Corrosion Induced Leakage Problem of the Radial Beam Port 1 of BAEC Triga Mark-II Research Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kalam, A.; Salam, M. A.; Sarder, M. A.; Rahman, M. M.; Rahman, M.; Rahman, A.; Chowdhury, A. Z.; Uddin, M. S.; Haque, M. M.; Zulquarnain, M.A., E-mail: kalambaec@yahoo.com [Reactor Operation and Maintenance Unit, Atomic Energy Research Establishment (AERE), Dhaka (Bangladesh)

    2014-08-15

    The BAEC reactor has so far been operated as per the technical specifications and procedures laid down in the SAR of the research reactor. The BP leakage problem of the BAEC research reactor was an issue that could lead to a situation close to a LOCA. Therefore, the matter was handled carefully, taking all measures so that such an incident could be prevented. Assistance of agencies outside BAEC was taken for solving the problem. It is understood that the silicone rubber lining of the encirclement clamp may become damaged by neutron irradiation. Therefore, while designing the clamp, provisions were kept such that it can be dismantled and reinstalled again following lining replacement. As a moderately aged facility, the ageing management BAEC TRIGA research reactor deserves significant attention. BAEC, together with its strategic partners, are doing what is needed in this regard.

  14. Computational Analysis of Nuclear Safety Parameters of 3 MW TRIGA Mark-II Research Reactor Based on Evaluated Nuclear Data Libraries JENDL-3.3 and ENDF/B-VII.0

    International Nuclear Information System (INIS)

    Khan, Jahirul Haque

    2013-01-01

    The objective of this study is to explain the main nuclear safety parameters of 3 MW TRIGA Mark-II Research Reactor at AERE, Savar, Dhaka, Bangladesh from the viewpoint of reactor safety and also reactor operator. The most important nuclear reactor physics safety parameters are power distribution, power peaking factors, shutdown margin, control rod worth, excess reactivity and fuel temperature reactivity coefficient. These parameters are calculated using the chain of the computer codes the SRAC-PIJ for cell calculation based on neutron transport theory and the SRAC-CITATION for core calculation based on neutron diffusion equation. To achieve this objective the TRIGA model is developed by the 3-D diffusion code SRAC-CITATION based on the group constants that come from the collision probability transport code SRAC-PIJ. In this study the evaluated nuclear data libraries JENDL-3.3 and ENDF/B-VII.0 are used. The calculated most important reactor physics parameters are compared to the safety analysis report (SAR) values as well as earlier published MCNP results (numerically benchmark). It was found that the calculated results show a good agreement between the said libraries. Besides, in most cases the calculated results reveal a reasonable agreement with the SAR values (by General Atomic) as well as the MCNP results. In addition, this analysis can be used as the inputs for thermal-hydraulic calculations of the TRIGA fresh core in the steady state and pulse mode operation. Because of power peaking factors, power distributions and temperature reactivity coefficients are the most important reactor safety parameters for normal operation and transient safety analysis in research as well as in power reactors. They form the basis for technical specifications and limitations for reactor operation such as loading pattern limitations for pulse operation (in TRIGA). Therefore, this analysis will be very important to develop the nuclear safety parameters data of 3 MW TRIGA Mark

  15. Computational analysis of neutronic parameters for TRIGA Mark-II research reactor using evaluated nuclear data libraries ENDF/B-VII.0 and JENDL-3.3

    International Nuclear Information System (INIS)

    Altaf, M.H.; Badrun, N.H.; Chowdhury, M.T.

    2015-01-01

    Highlights: • SRAC-PIJ code and SRAC-CITATION have been utilized to model the core. • Most of the simulated results show no significant differences with references. • Thermal peak flux varies a bit due to up condition of TRIGA. • ENDF/B-VII.0 and JENDL-3.3 libraries perform well for neutronics analysis of TRIGA. - Abstract: Important kinetic parameters such as effective multiplication factor, k eff , excess reactivity, neutron flux and power distribution, and power peaking factors of TRIGA Mark II research reactor in Bangladesh have been calculated using the comprehensive neutronics calculation code system SRAC 2006 with the evaluated nuclear data libraries ENDF/B-VII.0 and JENDL-3.3. In the code system, PIJ code was employed to obtain cross section of the core cells, followed by the integral calculation of neutronic parameters of the reactor conducted by CITATION code. All the analyses were performed using the 7-group macroscopic cross section library. Results were compared to the experimental data, the safety analysis report (SAR) of the reactor provided by General Atomic as well as to the simulated values by numerically benchmarked MCNP4C, WIMS-CITATION and SRAC-CITATION codes. The maximum power densities at the hot spot were found to be 169.7 W/cc and 170.1 W/cc for data libraries ENDF/B-VII.0 and JENDL-3.3, respectively. Similarly, the total peaking factors based on ENDF/B-VII.0 and JENDL-3.3 were calculated as 5.68 and 5.70, respectively, which were compared to the original SAR value of 5.63, as well as to MCNP4C, WIMS-CITATION and SRAC-CITATION results. It was found in most cases that the calculated results demonstrate a good agreement with our experiments and published works. Therefore, this analysis benchmarks the code system and will be helpful to enhance further neutronics and thermal hydraulics study of the reactor

  16. Data acquisition and signal processing system for IPR R1 TRIGA-Mark I nuclear research reactor of CDTN

    International Nuclear Information System (INIS)

    Mesquita, A.Z.; Maretti, F. Jr.; Rezende, H.C.; Tambourgi, E.B.

    2004-01-01

    The TRIGA IPR-R1 Nuclear Research Reactor, located at the Nuclear Technology Development Center (CDTN/CNEN) in Belo Horizonte, Brazil, is being operated since 44 years ago. The main operational parameters were monitored by analog recorders and counters located in the reactor control console. The reactor operators registered the most important operational parameters and data in the reactor logbook. This process is quite useful, but it can involve some human errors. It is also impossible for the operators to take notes of all variables involving the process mainly during fast power transients in some operations. A PC-based data acquisition was developed for the reactor that allows online monitoring, through graphic interfaces, and shows operational parameters evolution to the operators. Some parameters that were not measured, like the power and the coolant flow rate at the primary loop, are monitored now in the computer video monitor. The developed system allows measuring out all parameters in a frequency up to 1 kHz. These data is also recorded in text files available for consults and analysis. (author)

  17. Refurbishment, Modernization and Ageing Management Program of The 3MW TRIGA Mark-II Research Reactor of Bangladesh

    International Nuclear Information System (INIS)

    Salam, M. A.

    2013-01-01

    The 3 MW TRIGA MK-II research reactor of Bangladesh Atomic Energy Commission (BAEC) achieved its first criticality on 14 September 1986. The reactor has been used for manpower training, radioisotope production and various R and D activities in the field of neutron activation analysis, neutron radiography and neutron scattering. Reactor Operation and Maintenance Unit (ROMU) is responsible for operation and maintenance of the research reactor. During the past twenty seven years ROMU carried out several refurbishments, replacement, modification and modernization activities in the reactor facility. The major tasks carried out under refurbishment program were replacement of the corrosion damaged N-16 decay tank by a new one, replacement of the fouled shell and tube type heat exchanger by a plate type one, modification of the shielding arrangements around the N-16 decay tank and ECCS system and solving the radial beam port-1 leakage problem. All of these refurbishment activities were performed under an annual development project (ADP) funded by Bangladesh government. BAEC research reactor (RR) was operated by analogue console system from its commissioning to July, 2011. Old analog based console has been replaced by digital console on June, 2012. Modernization program for the reactor control console due to obsolescence and unavailability of spare parts of I and C system was vital to restore the safe operation of the reactor. Considering these facts, installation of a digital control console and I and C system based on the state-of-the-art digital technology became necessary. Reactor digital console system installation tasks were performed under another ADP funded project by Bangladesh government. Now the reactor is operating with the digital control system. Besides this, the Neutron Radiography (NR) facility has been modernized by the addition of a digital neutron radiography set-up at the tangential beam port. The Neutron Scattering (NS) facility also has been upgraded

  18. Refurbishment, Modernization and Ageing Management Program of The 3MW TRIGA Mark-II Research Reactor of Bangladesh

    Energy Technology Data Exchange (ETDEWEB)

    Salam, M. A. [Atomic Energy Research Establishment, Dhaka (Bangladesh)

    2013-07-01

    The 3 MW TRIGA MK-II research reactor of Bangladesh Atomic Energy Commission (BAEC) achieved its first criticality on 14 September 1986. The reactor has been used for manpower training, radioisotope production and various R and D activities in the field of neutron activation analysis, neutron radiography and neutron scattering. Reactor Operation and Maintenance Unit (ROMU) is responsible for operation and maintenance of the research reactor. During the past twenty seven years ROMU carried out several refurbishments, replacement, modification and modernization activities in the reactor facility. The major tasks carried out under refurbishment program were replacement of the corrosion damaged N-16 decay tank by a new one, replacement of the fouled shell and tube type heat exchanger by a plate type one, modification of the shielding arrangements around the N-16 decay tank and ECCS system and solving the radial beam port-1 leakage problem. All of these refurbishment activities were performed under an annual development project (ADP) funded by Bangladesh government. BAEC research reactor (RR) was operated by analogue console system from its commissioning to July, 2011. Old analog based console has been replaced by digital console on June, 2012. Modernization program for the reactor control console due to obsolescence and unavailability of spare parts of I and C system was vital to restore the safe operation of the reactor. Considering these facts, installation of a digital control console and I and C system based on the state-of-the-art digital technology became necessary. Reactor digital console system installation tasks were performed under another ADP funded project by Bangladesh government. Now the reactor is operating with the digital control system. Besides this, the Neutron Radiography (NR) facility has been modernized by the addition of a digital neutron radiography set-up at the tangential beam port. The Neutron Scattering (NS) facility also has been upgraded

  19. Operation and maintenance of the 250 kW TRIGA Mark II reactor at the J. Stefan Institute

    International Nuclear Information System (INIS)

    Dimic, V.

    1980-01-01

    Since the last TRIGA Conference, the reactor has completed approximately 4800 operating hours without major problems. The problem with the lack of fresh fuel elements is going to be solved after the signing of a new agreement for the supply of fuel between the IAEA, the Yugoslav and US Governments. In order to increase the reactivity the fuel elements from the outer zone we shuffled to the inner zone, and old fuel elements from the fuel container were added to the F ring. Due to the large demand for irradiation, a new pneumatic facility for loading and unloading the samples in the rotary specimen rack or central thimble has been constructed and installed. A configuration based on two microcomputers in a master slave hierarchical organisation for automatic data logging and direct has been finished and the system was installed after extensive testing. The reactor operation is now more reliable and simpler for the operators. Some of the original instrumentation of the reactor has been gradually substituted because of ageing: a start-up channel with digital display, a power integrator, a digital electronic rod position indicator, a digital power range switch without resistors and a new 2-pen recorder have been installed. The following instrumentation was ordered by the IAEA from the Hartmann and Brawn company: a start-up channel, a log channel, a safety channel, an automatic power control and water temperature, conductivity, level and activity measuring units. During the last year, with the help of our nuclear chemistry department, the production of high concentration and high purity technetium-99 m for medical use was developed by a solvent extraction method

  20. Comparison of neutron fluxes obtained by 2-D and 3-D geometry with different shielding libraries in biological shield of the TRIGA MARK II reactor

    International Nuclear Information System (INIS)

    Bozic, M.; Zagar, T.; Ravnik, M.

    2003-01-01

    Neutron fluxes in different spatial locations in biological shield are obtained with TORT code (TORT-Three Dimensional Oak Ridge Discrete Ordinates Neutron/Photon Transport Code). Libraries used with TORT code were BUGLE-96 library (coupled library with 47 neutron groups and 20 gamma groups) and VITAMIN-B6 library (coupled library with 199 neutron groups and 42 gamma groups). BUGLE-96 library is derived from VITAMIN-B6 library. 2-D and 3-D models for homogeneous type of problem (without inserted beam port 4) and problem with asymmetry (non-homogeneous problem; inserted beam port 4, filled with different materials) were of interest for neutron flux calculation. The main purpose is to verify the possibility for using 2-D approximation model instead of large 3-D model in some calculations. Another purpose of this paper was to compare neutron spectral constants obtained from neutron fluxes (3-D model) determined with smaller BUGLE-96 library with new constants obtained from fluxes calculated with bigger VITAMIN-B6 library. These neutron spectral constants are used in isotopic calculation with SCALE code package (ORIGEN-S). In past only neutron spectral constants determined by neutron fluxes from BUGLE-96 library were used. Experimental results used for isotopic composition comparison are available from irradiation experiment with selected type of concrete and other materials in beam port 4 (irradiation channel 4) in TRIGA Mark II reactor. These experimental results were used as a benchmark in this paper. (author)

  1. Power level control of the TRIGA Mark-II research reactor using the multifeedback layer neural network and the particle swarm optimization

    International Nuclear Information System (INIS)

    Coban, Ramazan

    2014-01-01

    Highlights: • A multifeedback-layer neural network controller is presented for a research reactor. • Off-line learning of the MFLNN is accomplished by the PSO algorithm. • The results revealed that the MFLNN–PSO controller has a remarkable performance. - Abstract: In this paper, an artificial neural network controller is presented using the Multifeedback-Layer Neural Network (MFLNN), which is a recently proposed recurrent neural network, for neutronic power level control of a nuclear research reactor. Off-line learning of the MFLNN is accomplished by the Particle Swarm Optimization (PSO) algorithm. The MFLNN-PSO controller design is based on a nonlinear model of the TRIGA Mark-II research reactor. The learning and the test processes are implemented by means of a computer program at different power levels. The simulation results obtained reveal that the MFLNN-PSO controller has a remarkable performance on the neutronic power level control of the reactor for tracking the step reference power trajectories

  2. Nuclear and radiological safety in the substitution process of the fuel HEU to LEU 30/20 in the Reactor TRIGA Mark III of the ININ

    International Nuclear Information System (INIS)

    Hernandez G, J.

    2012-10-01

    Inside the safety initiative in the international ambit, with the purpose of reducing the risks associated with the use of high enrichment nuclear fuels (HEU) for different proposes to the peaceful uses of the nuclear energy, Mexico contributes by means of the substitution of the high enrichment fuel HEU for low enrichment fuel LEU 30/20 in the TRIGA Mark III Reactor, belonging to Instituto Nacional de Investigaciones Nucleares (ININ). The conversion process was carried out by means of the following activities: analysis of the proposed core, reception and inspection of the fuel LEU 30/20, the discharge of the fuels of the mixed reactor core, shipment of the fuels HEU fresh and irradiated to the origin country, reload activities with the fuels LEU 30/20 and parameters measurement of the core operation. In order to maintaining the personnel's integrity and infrastructure associated to the Reactor, during the whole process the measurements of nuclear and radiological safety were controlled to detail, in execution with the license requirements of the installation. This work describes the covering activities and radiological inspections more relevant, as well as the measurements of radiological control implemented with base in the estimate of the equivalent dose of the substitution process. (Author)

  3. Thermal power calibration of the TRIGA Mark I IPR-R1 reactor during the upgrading tests to 250 kW

    International Nuclear Information System (INIS)

    Mesquita, Amir Zacarias; Maretti, Fausto Junior; Rezende, Hugo Cesar

    2002-01-01

    This paper presents the results and the methodology used to calibrate the thermal power of the TRIGA MARK I IPR-R1 Reactor in CDTN, Belo Horizonte, Brazil. This calibration was realized during the operation tests carried out to allow the reactor power upgrade from the current 100 kW to 250 kW. The methodology consisted in the measurement of the inlet and outlet temperature and the water flow in the primary cooling loop. The thermal balance together with the thermal losses gave the thermal power. There were made three sequences of tests. The first rising of the thermal power was made with the usual configuration of the core (59 fuel elements). After the changing of the ion chambers position and the control rod and the increase of the number of fuels (63 fuel elements), a new evaluation of the thermal power was accomplished, having been obtained a thermal power of 234 kW, for an indication of 250 kW in the lineal channel. After the return of the core to the initial configuration (59 fuel elements), it took place a new test, getting back the reactor to the power level of 100 kW. (author)

  4. Design, construction and implementation of two redundant circuits of the actuation logic of the protection system of the new control console of TRIGA Mark III reactor of ININ

    International Nuclear Information System (INIS)

    Celestino M, E.

    2016-01-01

    The Instituto Nacional de Investigaciones Nucleares (ININ) in Mexico has a nuclear reactor type TRIGA Mark III, which was put into operation in 1968. The reactor is used for staff training, radioisotope production, and for research projects of different areas. Over time and due to advances constantly has the electronics industry, maintenance of electronic systems is complicated because basically sometimes components that are no longer manufactured or no longer exist in the market, making it necessary to create projects required modernization. This is the case of the TRIGA reactor of ININ, so the Department of Automation and Instrumentation ININ is undertaking a new project to update the reactor control console. Systems that make up a nuclear reactor protection system (Ps) is relevant, since it is responsible for generating the necessary steps to shut down the reactor to an event of uncertainty which could affect the operators or the installation own actions. As part of the renovation project, this study design is presented to update the Logic of Action (La) of the Ps, whose final design must meet the requirements or specifications set by users and or regulations applicable to nuclear research reactors. One of the requirements established for the proposed new design La, is that it must be implemented with components and devices manufactured with latest technologies, and readily available on the market. The design which is operating currently uses TTL logic whose components are no longer available in the market, so for the new design you decide to use programmable circuits, and specifically, the CPLDs called (by the acronym Complex Programmable Logic Device). These CPLDs are electronic devices that solve complex logic equations and meeting the requirements of functionality and modernity for the new design of the La. In this work the criteria used for the selection of the CPLDs considering the availability and ease of software and hardware to use, and the design and

  5. Simulation development for TRIGA reactor

    International Nuclear Information System (INIS)

    Handoyo, D.

    1997-01-01

    A simulator of the dynamic of TRIGA reactor has been made. this simulator is meant to study the reactor kinetic behavior and for operator training to more assure the safety and the reliability of the real operation of TRIGA reactor. the simulator consists of PC (Personal Computer) for processing the calculation of reactivity, neutron flux, period, ect and control panel for regulating the input data such as the change of power range, control rod position as well as cooling flow rate. the result will be displayed on screen monitor of personal computer as given in the real control room of TRIGA reactor. the output of simulator will be verified by comparing with measurement result in the real TRIGA MARK II reactor of Musashi institute of technology. for the change of reactivity of 0.3, 0.5 and 0.7 the reactor power and fuel temperature between the simulator and measurements are comparable

  6. Survey of nuclear parameters from the TRIGA Mark I IPR R1 Brazilian reactor with concentric configuration aiming the application of K0 neutron activation technique

    International Nuclear Information System (INIS)

    Franco, Milton Batista

    2006-01-01

    This research intended to determine the nuclear parameters a, f, spectral index and neutron temperature in several irradiations positions of the TRIGA Mark 1 IPR-R1 reactor, for use on the parametric method K 0 in the CDTN. K 0 is a monostandard method of neutron activation analysis. It is, on the whole, experimentally simple, flexible and an important tool for accurate and convenient standardization in instrumental multi-element analysis. At the time the parameters were determined at the rotatory rack, lower layer and in the central thimble: alpha was calculated applying the three bare monitor method using 197 Au, 94 Zr and 96 Zr; f determination was done according to the bare bi-isotopic method; neutron temperature was calculated through the direct method using 176 Lu, 94 Zr, 96 Zr and 197 Au and the Westcott's g(Tn) function for the 176 Lu was calculated and the result was interpolated in the Grintakis and Kim (1975) Table, determining the neutron temperature. The procedure to check the parameters consisted in using standard solutions of Au (metal foil, NBS), Lu (LuO 2 , Johnson Mattey Company - JMC) and Zr (ZrO 2 and metal foil, Johnson Mattey Company 99,99% and Zry - 4: 98,14% of Zr, National Bureau of Standard- NBS). Several certified reference materials and two samples of intercomparisons (samples of sediment of the IAEA/ARCAL XXVI project) have been analysed by means of k 0 - INAA in order to verify the efficiency of the method and the quality of the parameters. The certified reference materials were: GXR-2, GXR-5 and GXR-6 of the United States Geological Survey (USGS) and Soil-5, Soil-7 and SL-1 of the International Atomic Energy Agency (IAEA). (author)

  7. Support to the elaboration of the engineering of detail, configuration and programming of the control system of heat removal of the TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Diaz G, C. A.

    2016-01-01

    Nowadays, the peaceful and responsible use of nuclear energy in Mexico is of great importance and contributes to economic, social, scientist and technologic development in the country, highlighting the Instituto Nacional de Investigaciones Nucleares (ININ) and the Nuclear Power Plant of Laguna Verde as one of the most important dependences. Among the main facilities and laboratories of ININ is the Nuclear Research Reactor TRIGA Mark III, this is a pool type reactor with mobile core, cooled and moderated by light water and a flow of 1013 n/cm"2/sec. Due to the technological obsolescence is a growing problem that threatens the information, operation and/or efficacy of elements of control and safety systems of the reactor, these must be changed each time more frequently. In the modernization of reactor was used a Modicon M340 programmable logic control (PLC) and a Twido PLC for the control of heat removal system (Primary Cooling System (PCS) and Secondary Cooling System (SCS) respectively), this because the PLC has proven to be safe and effective devices, addition to reduce the wiring elements and increase the possibilities of performance and design of the digital control console. This document shows and describes the elements of heat removal system (PCS and SCS), and the signals and signal types that such items send or received by the PLC, likewise, is indicated the methodology used to develop the applications for the control of the Primary Cooling System and Secondary Cooling System, beginning with the PLC design, the development of PLC plans and the control logic, and finally, the simulation and debugging of applications on Unity Pro and Twido Suite. All this in compliance with the safety standards to nuclear research reactors (NS-R-4), the rules of industrial programming (IEC 61131-3), and the reactor operating limits postulated in the safety report and the software assurance system used in the ININ. (Author)

  8. Theoretical evaluation of the production of the poisons Xe-135 and Sm-149 of the TRIGA Mark III reactor with mixed core

    International Nuclear Information System (INIS)

    Paredes G, L.C.

    1991-11-01

    It was theoretically determined the accumulation of the Xe 135 and Sm 149 in function, of the time during a stationary state of 72 h. continuous for the reactor TRIGA Mark III to 1 MW of thermal power with mixed core. The values of negative reactivity due to these isotopes are of 2.04 dollars and 0.694 dollars to the 72 h, quantities that will have to be compensated if wants that the reactor continues working to this power. Under the same conditions but considering a core with standard fuel, it was found a value of ρ = 1.70 dollars, resulting a difference of 0.30 dollars of negative reactivity in function of the type of analyzed core. This difference is important for the calculations of fuel management of a reactor. The concentration in balance of the xenon was reaches after an operation to constant power of 1 MW by 50 h, contrary to the samarium that reaches it balance after 3 weeks of operation starting from the initial start up and it stays constant along the useful life of the reactor while a change of fuel doesn't exist. It was obtained that for operation times greater to 60 h. at 1 MW, a peak of negative reactivity of the Xe 135 is generated between the 7 and 11 h after the instantaneous shut down, with a value of 2.43 dollars, that is to say 0.39 additional dollars to those taken place during the continuous irradiation. (Author)

  9. Validation of absolute axial neutron flux distribution calculations with MCNP with 197Au(n,γ)198Au reaction rate distribution measurements at the JSI TRIGA Mark II reactor.

    Science.gov (United States)

    Radulović, Vladimir; Štancar, Žiga; Snoj, Luka; Trkov, Andrej

    2014-02-01

    The calculation of axial neutron flux distributions with the MCNP code at the JSI TRIGA Mark II reactor has been validated with experimental measurements of the (197)Au(n,γ)(198)Au reaction rate. The calculated absolute reaction rate values, scaled according to the reactor power and corrected for the flux redistribution effect, are in good agreement with the experimental results. The effect of different cross-section libraries on the calculations has been investigated and shown to be minor. Copyright © 2013 Elsevier Ltd. All rights reserved.

  10. TRIGA reactor as an experimental tool

    Energy Technology Data Exchange (ETDEWEB)

    Nahrul Khair bin Alang Mohammad Rashid (PUSPATI, Selangor (Malaysia))

    1981-01-01

    Article reviewed on the general features, operation and capabilities, and utilization of a research reactor, PUSPATI TRIGA MARK II. The paper also described the arrangements for the use of the PUSPATI reactor.

  11. Triga reactor as an experimental tool

    International Nuclear Information System (INIS)

    Nahrul Khair bin Alang Mohammad Rashid

    1981-01-01

    Article reviewed on the general features, operation and capabilities, and utilization of a research reactor, PUSPATI TRIGA MARK II. The paper also described the arrangements for the use of the PUSPATI reactor

  12. Experimental evaluation of the production of the poisons Xe-135 and Sm-149 of the TRIGA Mark III reactor with mixed core, configuration No. 16 (Final report of the project); Evaluacion experimental de la produccion de los venenos Xe-135 y Sm-149 del reactor TRIGA Mark III con nucleo mixto, config. No. 16 (Informe final del proyecto)

    Energy Technology Data Exchange (ETDEWEB)

    Paredes G, L C

    1991-11-15

    It was generated the concentration curve of the Xe{sup 135} (t) during the TRIGA Mark III reactor operation cycle, for a continuous irradiation of 72 h to 1 MW of thermal power, as well as the accumulation curve of the isotope after the shutdown, for the fuel configuration No. 16 in the thermal column. The maximum negative reactivities generated by the Xe{sup 135} for operation times greater than 60 h to 1 MW and after the reactor shutdown its were of 1.968 {+-} 0.15 dollars and 2.30 {+-} 0.15 dollars respectively. When comparing these results with those theoretically calculated we find differences of the order of 3.6% and 5.34% which are understood inside the experimental error that on the average was of 7.6%. The results before mentioned have an important application during the start up process of the Reactor, when analyzing the value of the weekly reactivity excess of the core and when is choice the pattern of bars to use for experiments of but of 2 h, where is required to minimize the temporary and space interferences of the neutron flux. (Author)

  13. Design, construction and implementation of two redundant circuits of the actuation logic of the protection system of the new control console of TRIGA Mark III reactor of ININ; Diseno, construccion e implementacion de dos circuitos redundantes de la logica de actuacion del sistema de proteccion de la nueva consola de control del reactor Triga Mark III del ININ

    Energy Technology Data Exchange (ETDEWEB)

    Celestino M, E.

    2016-07-01

    The Instituto Nacional de Investigaciones Nucleares (ININ) in Mexico has a nuclear reactor type TRIGA Mark III, which was put into operation in 1968. The reactor is used for staff training, radioisotope production, and for research projects of different areas. Over time and due to advances constantly has the electronics industry, maintenance of electronic systems is complicated because basically sometimes components that are no longer manufactured or no longer exist in the market, making it necessary to create projects required modernization. This is the case of the TRIGA reactor of ININ, so the Department of Automation and Instrumentation ININ is undertaking a new project to update the reactor control console. Systems that make up a nuclear reactor protection system (Ps) is relevant, since it is responsible for generating the necessary steps to shut down the reactor to an event of uncertainty which could affect the operators or the installation own actions. As part of the renovation project, this study design is presented to update the Logic of Action (La) of the Ps, whose final design must meet the requirements or specifications set by users and or regulations applicable to nuclear research reactors. One of the requirements established for the proposed new design La, is that it must be implemented with components and devices manufactured with latest technologies, and readily available on the market. The design which is operating currently uses TTL logic whose components are no longer available in the market, so for the new design you decide to use programmable circuits, and specifically, the CPLDs called (by the acronym Complex Programmable Logic Device). These CPLDs are electronic devices that solve complex logic equations and meeting the requirements of functionality and modernity for the new design of the La. In this work the criteria used for the selection of the CPLDs considering the availability and ease of software and hardware to use, and the design and

  14. The Slovenian bibliography

    Directory of Open Access Journals (Sweden)

    Lidija Wagner

    2000-01-01

    Full Text Available The Slovenian bibliography is our national bibliography. We want to show the criteria of the selection of the particular materials, which are included in the Slovenian bibliography. We described the bibliographic description and classification of the records with UDC and the descriptors. The printing and the CD-ROM issues of the Slovenian bibli¬ography are described. We compared UNESCO guidelines for the national bibliography on the field of the selection, bibliographic description and classification, arrangement of the records and the useful of the national bibliography.

  15. Support to the elaboration of the engineering of detail, configuration and programming of the control system of heat removal of the TRIGA Mark III reactor; Apoyo a la elaboracion de la ingenieria de detalle, configuracion y programacion del sistema de control de remocion de calor del reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Diaz G, C. A.

    2016-07-01

    Nowadays, the peaceful and responsible use of nuclear energy in Mexico is of great importance and contributes to economic, social, scientist and technologic development in the country, highlighting the Instituto Nacional de Investigaciones Nucleares (ININ) and the Nuclear Power Plant of Laguna Verde as one of the most important dependences. Among the main facilities and laboratories of ININ is the Nuclear Research Reactor TRIGA Mark III, this is a pool type reactor with mobile core, cooled and moderated by light water and a flow of 1013 n/cm{sup 2}/sec. Due to the technological obsolescence is a growing problem that threatens the information, operation and/or efficacy of elements of control and safety systems of the reactor, these must be changed each time more frequently. In the modernization of reactor was used a Modicon M340 programmable logic control (PLC) and a Twido PLC for the control of heat removal system (Primary Cooling System (PCS) and Secondary Cooling System (SCS) respectively), this because the PLC has proven to be safe and effective devices, addition to reduce the wiring elements and increase the possibilities of performance and design of the digital control console. This document shows and describes the elements of heat removal system (PCS and SCS), and the signals and signal types that such items send or received by the PLC, likewise, is indicated the methodology used to develop the applications for the control of the Primary Cooling System and Secondary Cooling System, beginning with the PLC design, the development of PLC plans and the control logic, and finally, the simulation and debugging of applications on Unity Pro and Twido Suite. All this in compliance with the safety standards to nuclear research reactors (NS-R-4), the rules of industrial programming (IEC 61131-3), and the reactor operating limits postulated in the safety report and the software assurance system used in the ININ. (Author)

  16. Survey of nuclear parameters from the TRIGA Mark I IPR R1 Brazilian reactor with concentric configuration aiming the application of K{sub 0} neutron activation technique; Levantamento de parametros nucleares do reator TRIGA Mark I IPR R1 com configuracao concentrica visando a aplicacao da tecnica de ativacao neutronica K{sub 0}

    Energy Technology Data Exchange (ETDEWEB)

    Franco, Milton Batista

    2006-07-01

    This research intended to determine the nuclear parameters a, f, spectral index and neutron temperature in several irradiations positions of the TRIGA Mark 1 IPR-R1 reactor, for use on the parametric method K{sub 0} in the CDTN. K{sub 0} is a monostandard method of neutron activation analysis. It is, on the whole, experimentally simple, flexible and an important tool for accurate and convenient standardization in instrumental multi-element analysis. At the time the parameters were determined at the rotatory rack, lower layer and in the central thimble: alpha was calculated applying the three bare monitor method using {sup 197}Au, {sup 94}Zr and {sup 96}Zr; f determination was done according to the bare bi-isotopic method; neutron temperature was calculated through the direct method using {sup 176}Lu, {sup 94}Zr, {sup 96}Zr and {sup 197}Au and the Westcott's g(Tn) function for the {sup 176}Lu was calculated and the result was interpolated in the Grintakis and Kim (1975) Table, determining the neutron temperature. The procedure to check the parameters consisted in using standard solutions of Au (metal foil, NBS), Lu (LuO{sub 2}, Johnson Mattey Company - JMC) and Zr (ZrO{sub 2} and metal foil, Johnson Mattey Company 99,99% and Zry - 4: 98,14% of Zr, National Bureau of Standard- NBS). Several certified reference materials and two samples of intercomparisons (samples of sediment of the IAEA/ARCAL XXVI project) have been analysed by means of k{sub 0}- INAA in order to verify the efficiency of the method and the quality of the parameters. The certified reference materials were: GXR-2, GXR-5 and GXR-6 of the United States Geological Survey (USGS) and Soil-5, Soil-7 and SL-1 of the International Atomic Energy Agency (IAEA). (author)

  17. Theoretical evaluation of the production of the poisons Xe-135 and Sm-149 of the TRIGA Mark III reactor with mixed core; Evaluacion teorica de la produccion de los venenos Xe-135 y Sm-149 del reactor TRIGA Mark III con nucleo mixto

    Energy Technology Data Exchange (ETDEWEB)

    Paredes G, L.C

    1991-11-15

    It was theoretically determined the accumulation of the Xe{sup 135} and Sm {sup 149} in function, of the time during a stationary state of 72 h. continuous for the reactor TRIGA Mark III to 1 MW of thermal power with mixed core. The values of negative reactivity due to these isotopes are of 2.04 dollars and 0.694 dollars to the 72 h, quantities that will have to be compensated if wants that the reactor continues working to this power. Under the same conditions but considering a core with standard fuel, it was found a value of {rho} = 1.70 dollars, resulting a difference of 0.30 dollars of negative reactivity in function of the type of analyzed core. This difference is important for the calculations of fuel management of a reactor. The concentration in balance of the xenon was reaches after an operation to constant power of 1 MW by 50 h, contrary to the samarium that reaches it balance after 3 weeks of operation starting from the initial start up and it stays constant along the useful life of the reactor while a change of fuel doesn't exist. It was obtained that for operation times greater to 60 h. at 1 MW, a peak of negative reactivity of the Xe{sup 135} is generated between the 7 and 11 h after the instantaneous shut down, with a value of 2.43 dollars, that is to say 0.39 additional dollars to those taken place during the continuous irradiation. (Author)

  18. Spatial dependence of the void coefficient in the interstitial coolant channel positions of a stainless steel-clad TRIGA Mark I core

    International Nuclear Information System (INIS)

    Spriggs, Gregory D.; Nelson, George W.; Doane, Harry J.

    1982-01-01

    A new top grid plate was manufactured and installed in the U of A TRIGA. The new grid plate was identical to the old grid plate with respect to the fuel element array, but included two minor modifications; 1) 3/8'' holes were drilled in six interstitial positions between fuel element rings to allow for insertion of a small diameter void rod for void coefficient measurements in the coolant channels, and 2) flux wire holes were drilled in all remaining interstitial positions. The purpose of this report is to update the previously reported void coefficient measurements with data taken in one of the coolant channel positions

  19. Research activities at the TRIGA Mainz

    International Nuclear Information System (INIS)

    Eberhardt, K.; Trautmann, N.

    2002-01-01

    The TRIGA Mark II reactor of the Mainz University became first critical on August 3, 1965. It can be operated in the steady state mode with a maximum power of 100 kW and in the pulse mode with a peak power of 250 MW. The TRIGA Mainz is mainly used for neutron activation analysis, isotope production, basic research in nuclear chemistry and nuclear physics as well as for education and training

  20. The Design of a Prompt Gamma Neutron Activation Analysis Beam for BNCT Purpose at the TRIGA Mark II Reactor in Pavia

    Energy Technology Data Exchange (ETDEWEB)

    Stella, S.; Bazani, A.; Ballarini, F.; Bortolussi, S.; Protti, N.; Altieri, S. [Department of Nuclear and Theoretical Physics, University of Pavia (Italy); Istituto Nazionale di Fisica Nucleare (INFN), Section of Pavia (Italy); Bruschi, P. [Department of Nuclear and Theoretical Physics, University of Pavia (Italy)

    2011-07-01

    In preclinical and clinical Boron Neutron Capture Therapy studies the knowledge of the amount of {sup 10}B in blood and tissues is very important. The boron concentration measurements method used in Pavia (Italy) is based on the charged particles spectrometry of thin tissue cuts irradiated in the Thermal Column of the TRIGA reactor of the University. In order to perform measurements in biological liquids such as blood and urine, or in other tissue that cannot be cut in slices, a Prompt Gamma Neutron Activation Analysis (PGNAA) facility is being designed, which measures {sup 10}B concentration detecting the prompt gamma from boron nuclear capture reaction. At the TRIGA reactor in Pavia, there are four horizontal channels, potentially available for PGNAA. The choice of the suitable channel, and the design of its configuration, were achieved using the Monte Carlo neutron transport code MCNP4c2. To perform the simulations, an input code already validated, describing the reactor structure and the neutron source, was used. The calculations were implemented applying non-analog techniques for the neutron transport, that are necessary to obtain a sufficient statistic in every positions along the channel and especially at its end. The selection of the channel for PGNAA installation was carried out by comparing the simulated fluxes obtained in the different channels at the present configuration. The channel shielded by the core reflector was chosen, because the graphite lowers the fast component of the neutrons, with no need to insert additional material in the facility. The thermal flux at its end is 1.7 x 10{sup 8} n/cm{sup 2} s with thermal-to-total neutron flux ratio around 0.8. Subsequently a bismuth block for gamma radiation shielding and blocks of single crystal sapphire as filter for fast neutron component were inserted in the channel. Other components of the facility that are under study are a collimator and the beam catcher. (author)

  1. The research reactor TRIGA Mainz

    International Nuclear Information System (INIS)

    Hampel, G.; Eberhardt, K.; Trautmann, N.

    2006-01-01

    The TRIGA Mark II reactor at the Institut fuer Kernchemie became first critical on August 3 rd , 1965. It can be operated in the steady state mode with a maximum power of 100 kWth and in the pulse mode with a peak power of 250 MWth. A survey of the research programmes performed at the TRIGA Mainz is given covering applications in basic research as well as applied science in nuclear chemistry and nuclear physics. Furthermore, the reactor is used for neutron activation analysis and for education and training of scientists, teachers, students and technical personal. Important projects for the future of the TRIGA Mainz are the UCN (ultra cold neutrons) experiment, fast chemical separation, medical applications and the use of the NAA as well as the use of the reactor facility for the training of students in the fields of nuclear chemistry, nuclear physics and radiation protection. Taking into account the past and future operation schedule and the typically low burn-up of TRIGA fuel elements (∝4 g U-235/a), the reactor can be operated for at least the next decade taking into account the fresh fuel elements on stock and without changing spent fuels. (orig.)

  2. Neutron activation analysis using TRIGA

    International Nuclear Information System (INIS)

    Byrne, A.R.

    1972-01-01

    Activation analysis with TRIGA MARK II is the main part of the work of the nuclear Chemistry Section at the Institute. A major part of the effort in this field is concerned with the determination of trace elements at the micro and nanogram level in a wide variety of materials, and with the development of new methods, (or the adaptation of known methods,) applicable to these determinations. In particular, specific and group radiochemical separations are studied

  3. LEADERSHIP DEVELOPMENTS IN SLOVENIAN COMPANIES

    Directory of Open Access Journals (Sweden)

    Andrej Kohont

    2016-04-01

    Full Text Available In this paper we study the relationship between the company and the leaders. We are interested what is characteristic of leadership in the best Slovenian companies. We used standardised employee questionnaire and data gathered in the Golden thread project. We observe the situation in these companies in the period between 2007 and 2014 to find out if there are any significant changes in leadership developments. Special attention in leadership observation is devoted to 1. The fundamental relationship between the company and the leaders, 2. The role and quality of leaders work, 3. Organizational culture, climate and relationships, 4. Entrepreneurship and innovation, 5. The quality of the working environment, 6. The personal growth and development and 7. Emotional commitment. The analysis represents an insight into current leadership situation and shows that the recent developments were heavily marked by the economic crisis, especially in 2009.

  4. TRIGA update and modification

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, G W; Seale, R L [University of Arizona (United States)

    1974-07-01

    The TRIGA originally installed at the University of Arizona in 1958 has been extensively modified. A Mark III console, rack-and-pinion regulating and shim control rods equipped with fuel-followers, a pneumatic transient rod, and a modern bridge structure were installed. The original 63 aluminum-clad fuel elements were shipped to the University of Utah in Salt Lake City and 85 partially used stainless-steel clad fuel elements were obtained from General Atomic in San Diego. The transfer and remodelling operation are summarized. A little more than one year of operation following these changes has been completed. Several instrumentation problems have been encountered and will be reported. The calibration of the partially spent fuel elements has been used to generate independent evaluations of prior fuel burnup. Finally, the utility of the reactor facility has been increased by adding a neutron radiography capability and a delayed neutron uranium assay system. (author)

  5. TRIGA reactor main systems

    International Nuclear Information System (INIS)

    Boeck, H.; Villa, M.

    2007-01-01

    This module describes the main systems of low power (<2 MW) and higher power (≥2 MW) TRIGA reactors. The most significant difference between the two is that forced reactor cooling and an emergency core cooling system are generally required for the higher power TRIGA reactors. However, those TRIGA reactors that are designed to be operated above 3 MW also use a TRIGA fuel that is specifically designed for those higher power outputs (3 to 14 MW). Typical values are given for the respective systems although each TRIGA facility will have unique characteristics that may only be determined by the experienced facility operators. Due to the inherent wide scope of these research reactor facilities construction and missions, this training module covers those systems found at most operating TRIGA reactor facilities but may also discuss non-standard equipment that was found to be operationally useful although not necessarily required. (author)

  6. TRIGA reactor characteristics

    International Nuclear Information System (INIS)

    Boeck, H.; Villa, M.

    2007-01-01

    This module describes the general design, characteristics and parameters of TRIGA reactors and fuels. It is recommended that most of this information should be incorporated into any reactor operator training program and, in many cases, the facility Safety Analysis Report. It is oriented to teach the basics of the physics and mechanical design of the TRIGA fuel as well as its unique operational characteristics and the differences between TRIGA fuels and others more traditional reactor fuels. (nevyjel)

  7. NRF TRIGA packaging

    International Nuclear Information System (INIS)

    Clements, M.D.

    1995-11-01

    Training Reactor Isotopes, General Atomics (TRIGA reg-sign) Reactors are in use at four US Department of Energy (DOE) complex facilities and at least 23 university, commercial, or government facilities. The development of the Neutron Radiography Facility (NRF) TRIGA packaging system began in October 1993. The Hanford Site NRF is being shut down and requires an operationally user-friendly transportation and storage packaging system for removal of the TRIGA fuel elements. The NRF TRIGA packaging system is designed to remotely remove the fuel from the reactor and transport the fuel to interim storage (up to 50 years) on the Hanford Site. The packaging system consists of a cask and an overpack. The overpack is used only for transport and is not necessary for storage. Based upon the cask's small size and light weight, small TRIGA reactors will find it versatile for numerous refueling and fuel storage needs. The NRF TRIGA packaging design also provides the basis for developing a certifiable and economical packaging system for other TRIGA reactor facilities. The small size of the NRF TRIGA cask also accommodates placing the cask into a larger certified packaging for offsite transport. The Westinghouse Hanford Company NRF TRIGA packaging, as described herein can serve other DOE sites for their onsite use, and the design can be adapted to serve university reactor facilities, handling a variety of fuel payloads

  8. Decommissioning of the Northrop TRIGA reactor

    International Nuclear Information System (INIS)

    Cozens, George B.; Woo, Harry; Benveniste, Jack; Candall, Walter E.; Adams-Chalmers, Jeanne

    1986-01-01

    An overview of the administrative and operational aspects of decommissioning and dismantling the Northrop Mark F TRIGA Reactor, including: planning and preparation, personnel requirements, government interfacing, costs, contractor negotiations, fuel shipments, demolition, disposal of low level waste, final survey and disposition of the concrete biological shielding. (author)

  9. Component failure data base of TRIGA reactors

    International Nuclear Information System (INIS)

    Djuricic, M.

    2004-10-01

    This compilation provides failure data such as first criticality, component type description (reactor component, population, cumulative calendar time, cumulative operating time, demands, failure mode, failures, failure rate, failure probability) and specific information on each type of component of TRIGA Mark-II reactors in Austria, Bangladesh, Germany, Finland, Indonesia, Italy, Indonesia, Slovenia and Romania. (nevyjel)

  10. Historical Slovenian Language Resources

    Directory of Open Access Journals (Sweden)

    Tomaž Erjavec

    2013-09-01

    Full Text Available EXTENDED ABSTRACT:The paper presents three language resources enabling better full-text access to digitised printed historical Slovenian texts: a hand-annotated corpus, a hand-annotated lexicon of historical words and a collection of transcribed texts. The aim of the resources is twofold: on one hand they support empirical linguistic research (corpus, collection and represent a reference tool for the research of historical Slovenian (lexicon while on the other hand they may serve as training data for the development of Human Language Technologies enabling better full-text search in digital libraries containing Slovenian written cultural heritage, modernisation of historical texts, and the development of better technological solutions for text recognition and scanning. The hand annotated corpus of historical Slovenian contains the text from 1,000 pages sampled from the years 1750 to 1900, two texts date to the end of the 16th or 17th century. The corpus contains a little more than 250,000 word tokens; each of them being annotated with hand validated linguistic features: modernised form, lemma or base form, and morhpo-syntactic description. Thus the word token »ajfram« is annotated with the normalised form »ajfrom«, by the lemma »ajfer« and morphosyntactic description »Som« or »Samostalnik« (noun, »občni« (common, »moški« (masculine and a modernised form »gorečnost« (fervour. At first the corpus was annotated automatically and then manually verified and corrected. The lexicon was created automatically from the hand-annotated corpus. It contains only attested word-forms and examples of use. The word-forms are ordered under their modern equivalents. All the modern forms of a particular word constitute a dictionary entry, defined by its lemma with conjoint information i.e. the morpho-syntactic description and the closest contemporary synonyms. Thus the entry »ajfrer/Som/gorečnost« is annotated by two modernised words »ajfra

  11. Optimum burnup of BAEC TRIGA research reactor

    International Nuclear Information System (INIS)

    Lyric, Zoairia Idris; Mahmood, Mohammad Sayem; Motalab, Mohammad Abdul; Khan, Jahirul Haque

    2013-01-01

    Highlights: ► Optimum loading scheme for BAEC TRIGA core is out-to-in loading with 10 fuels/cycle starting with 5 for the first reload. ► The discharge burnup ranges from 17% to 24% of U235 per fuel element for full power (3 MW) operation. ► Optimum extension of operating core life is 100 MWD per reload cycle. - Abstract: The TRIGA Mark II research reactor of BAEC (Bangladesh Atomic Energy Commission) has been operating since 1986 without any reshuffling or reloading yet. Optimum fuel burnup strategy has been investigated for the present BAEC TRIGA core, where three out-to-in loading schemes have been inspected in terms of core life extension, burnup economy and safety. In considering different schemes of fuel loading, optimization has been searched by only varying the number of fuels discharged and loaded. A cost function has been defined and evaluated based on the calculated core life and fuel load and discharge. The optimum loading scheme has been identified for the TRIGA core, the outside-to-inside fuel loading with ten fuels for each cycle starting with five fuels for the first reload. The discharge burnup has been found ranging from 17% to 24% of U235 per fuel element and optimum extension of core operating life is 100 MWD for each loading cycle. This study will contribute to the in-core fuel management of TRIGA reactor

  12. Research with Neutrons at the TRIGA Mainz

    International Nuclear Information System (INIS)

    Hampel, Gabriele

    2008-01-01

    The TRIGA Mark II reactor at the Institut fuer Kernchemie of the Johannes Gutenberg-Universitaet in Mainz became first critical on August 3, 1965 and is still intensively used for basic research, applied science and educational purposes. Considering the past and future operation schedule and the low burn-up of the fuel elements (∼4 g 235 U/a), the reactor can be operated for at least the next decade taking into account the fresh fuel elements on stock and without changing spent fuels. The operation of the TRIGA Mainz has been extended very recently until the year 2020. The TRIGA Mainz can be operated in the steady state mode with a maximum power of 100 kWth and in the pulse mode with a peak power of 250 MWth. Until now, more than 16600 pulses have been carried out without any fuel failure. For irradiations the TRIGA Mainz has a central experimental tube, three pneumatic transfer systems and a rotary specimen rack with 40 positions which allows the irradiation of 80 samples at the same time. In addition, the TRIGA Mainz includes four horizontal beam ports penetrating the concrete shielding and extending inside the pool towards the reflector. A graphite thermal column provides a source of well-thermalized neutrons suitable for physical research or biological and medical irradiations. Important projects for the future of the TRIGA Mainz are the production of ultracold neutrons (UCN) and experiments with UCN, high precision mass measurements and laser spectroscopy of short-lived fission products (TRIGA-TRAP), the production of radionuclides for fast chemical separations, medical and radiopharmaceutical applications, and the use of the neutron activation analysis for the application in archeometry, solar energy technique, criminalistics and vine analysis. Furthermore, studies are performed to judge if the Boron Neutron Capture Therapy (BNCT) can be applied at the TRIGA Mainz for cancer treatment of liver metastases. Also, the reactor facility is used for the training

  13. Some possibilities of utilisation of TRIGA reactors in the future

    International Nuclear Information System (INIS)

    Stegnar, Peter; Byrne, Anthony R.

    2008-01-01

    Full text. In this presentation, some possibilities for the future use of TRIGA reactors are discussed. The use and practical applications of neutron activation analysis, both in instrumental and radiochemical analysis, is presented based on the experience of the Institute's TRIGA Mark II Reactor in Ljubljana. The limited use of isotope production for medicine and industry is also discussed as well as some other potential applications, i.e. prompt gamma neutron activation analysis and an approach to BNCT (Boron Neutron Capture Therapy). The possibility of using TRIGA reactors for training in nuclear safety, radiological protection and other relevant fields of science and technology is also addressed in the presentation

  14. PUSPATI TRIGA Reactor

    International Nuclear Information System (INIS)

    Masood, Z.

    2016-01-01

    The PUSPATI TRIGA Reactor is the only research reactor in Malaysia. This 1 MW TRIGA Mk II reactor first reached criticality on 28 June 1982 and is located at the Malaysian Nuclear Agency premise in Bangi, Malaysia. This reactor has been mainly utilised for research, training and education and isotope production. Over the years several systems have been refurbished or modernised to overcome ageing and obsolescence problems. Major achievements and milestones will also be elaborated in this paper. (author)

  15. Modeling the PUSPATI TRIGA Reactor using MCNP code

    International Nuclear Information System (INIS)

    Mohamad Hairie Rabir; Mark Dennis Usang; Naim Syauqi Hamzah; Julia Abdul Karim; Mohd Amin Sharifuldin Salleh

    2012-01-01

    The 1 MW TRIGA MARK II research reactor at Malaysian Nuclear Agency achieved initial criticality on June 28, 1982. The reactor is designed to effectively implement the various fields of basic nuclear research, manpower training, and production of radioisotopes. This paper describes the reactor parameters calculation for the PUSPATI TRIGA REACTOR (RTP); focusing on the application of the developed reactor 3D model for criticality calculation, analysis of power and neutron flux distribution and depletion study of TRIGA fuel. The 3D continuous energy Monte Carlo code MCNP was used to develop a versatile and accurate full model of the TRIGA reactor. The model represents in detailed all important components of the core and shielding with literally no physical approximation. (author)

  16. Lexical Sentiment Analysis in Slovenian Texts

    OpenAIRE

    VOLČANŠEK, MATEJA

    2015-01-01

    The goal of this thesis is to create a sentiment dictionary for the Slovenian language which can be used in lexical methods for automatic sentiment analysis. We start from a sentiment dictionary for the English language, translate it semi-automatically to Slovenian and curate its content. We test the performance of using the translated dictionary for automated lexical sentiment analysis on a corpus of 5000 manually annotated Slovenian news articles gathered from the main Slovenian news por...

  17. Design improvements in TRIGA reactors

    International Nuclear Information System (INIS)

    Batch, John M.

    1970-01-01

    There have been many design improvements to TRIGA reactor hardware in the past twelve years. One of the more important and most obvious improvements has been in the area of reactor instrumentation. The low profile, completely transistorized Mark III console was a great step forward in a low maintenance, high reliability instrumentation system. Other design improvements include the lazy susan specimen pickup assembly; the specimen container; an empty stainless steel fuel element which can be filled with samples and can be located anywhere in the core; the flexible fuel handling tool; a new fuel measuring tool design; the shock absorber on the adjustable transient rod drive; new testing and evaluation procedures on the thermocouples and other

  18. Some concept for the TRIGA core design

    International Nuclear Information System (INIS)

    Aizawa, Otohiko

    1994-01-01

    There is the research reactor called TRIGA Mark-2 of 100 kW in Atomic Energy Research Laboratory, Musashi Institute of Technology. Recently, while the various calculations on the core were carried out, the author became aware of that this TRIGA core was designed at that time with excellent consideration. The reason for that is, although fuel is arranged in simple concentric circular state at a glance, it was known that in reality, this is the modification of the hexagonal core of triangular lattice. In the examination of square lattice fuel arrangement, the reactivity was calculated by using the gap between fuel rods as the parameter and by using ENDF/B-4 library and Monte Carlo code Keno-5. It is known that the design of the lattice with maximum reactivity cannot be done by the square lattice. The similar examination was carried out on triangular lattice, and it was found that the gap between fuel rods of 4 mm is the optimal design. The average neutron energy spectra in the fuel rods of the TRIGA Mark-2 core agreed considerably well with the energy spectra at 4.16 cm fuel rod pitch in triangular hexagonal core. In the reactor of about 100 kW, even if the gap between fuel rods is less than 4 mm, heat removal is sufficiently possible. (K.I.)

  19. Slovenian Mediterrananean and sustainable development

    Directory of Open Access Journals (Sweden)

    Mitja Bricelj

    2002-12-01

    Full Text Available Regional approach based on physical, social and economic characteristics of particular landscape what is basic input for sustainable development. The case Slovenian Mediterranean and sustainable development demonstrate public participation in the process of preparation of coastal management plan. For this process new forms of knowledge transfer to relevant public is needed to get their active position about different.

  20. TRIGA low enrichment fuel

    International Nuclear Information System (INIS)

    Gietzen, A.

    1993-01-01

    Sixty TRIGA reactors have been sold and the earliest of these are now passing twenty years of operation. All of these reactors use the uranium zirconium hydride fuel (UZrH) which provides certain unique advantages arising out of its large prompt negative temperature coefficient, very low fission product release, and high temperature capability. Eleven of these Sixty reactors are conversions from plate fuel to TRIGA fuel which were made as a result of these advantages. With only a few exceptions, TRIGA reactors have always used low-enriched uranium (LEU) fuel with an enrichment of 19.9%. The exceptions have either been converted from the standard low-enriched fuel to the 70% enriched FLIP fuel in order to achieve extended lifetime, or are higher powered reactors which were designed for long life using 93%-enriched uranium during the time when the use and export of highly enriched uranium (HEU) was not restricted. The advent of international policies focusing attention on nonproliferation and safeguards made the HEU fuels obsolete. General Atomic immediately undertook a development effort (nearly two years ago) in order to be in a position to comply with these policies for all future export sales and also to provide a low-enriched alternative to fully enriched plate-type fuels. This important work was subsequently partially supported by the U.S. Department of Energy. The laboratory and production tests have shown that higher uranium densities can be achieved to compensate for reducing the enrichment to 20%, and that the fuels maintain the characteristics of the very thoroughly proven standard TRIGA fuels. In May of 1978, General Atomic announced that these fuels were available for TRIGA reactors and for plate-type reactors with power levels up to 15 MW with General Atomic's standard commercial warranty

  1. TRIGA low enrichment fuel

    International Nuclear Information System (INIS)

    Gietzen, A.

    1993-01-01

    Sixty TRIGA reactors have been sold and the earliest of these are now passing twenty years of operation. All of these reactors use the uranium-zirconium hydride fuel (UZrH) which provides certain unique advantages arising out of its large prompt negative temperature coefficient, very low fission product release, and high temperature capability. Eleven of these Sixty reactors are conversions from plate fuel to TRIGA fuel which were made as a result of these advantages. With only a few exceptions, TRIGA reactors have always used low-enriched-uranium (LEU) fuel with an enrichment of 19.9%. The exceptions have either been converted from the standard low-enriched fuel to the 70% enriched FLIP fuel in order to achieve extended lifetime, or are higher powered reactors which were designed for long life using 93%-enriched uranium during the time when the use and export of highly enriched uranium (HEU) was not restricted. The advent of international policies focusing attention on nonproliferation and safeguards made the HEU fuels obsolete. General Atomic immediately undertook a development effort (nearly two years ago) in order to be in a position to comply with these policies for all future export sales and also to provide a low-enriched alternative to fully enriched plate-type fuels. This important work was subsequently partially supported by the U.S. Department of Energy. The laboratory and production tests have shown that higher uranium densities can be achieved to compensate for reducing the enrichment to 20%, and that the fuels maintain the characteristics of the very thoroughly proven standard TRIGA fuels. In May of 1978, General Atomic announced that these fuels were available for TRIGA reactors and for plate-type reactors with power levels up to 15 MW with GA's standard commercial warranty

  2. Monte Carlo modelling of TRIGA research reactor

    Science.gov (United States)

    El Bakkari, B.; Nacir, B.; El Bardouni, T.; El Younoussi, C.; Merroun, O.; Htet, A.; Boulaich, Y.; Zoubair, M.; Boukhal, H.; Chakir, M.

    2010-10-01

    The Moroccan 2 MW TRIGA MARK II research reactor at Centre des Etudes Nucléaires de la Maâmora (CENM) achieved initial criticality on May 2, 2007. The reactor is designed to effectively implement the various fields of basic nuclear research, manpower training, and production of radioisotopes for their use in agriculture, industry, and medicine. This study deals with the neutronic analysis of the 2-MW TRIGA MARK II research reactor at CENM and validation of the results by comparisons with the experimental, operational, and available final safety analysis report (FSAR) values. The study was prepared in collaboration between the Laboratory of Radiation and Nuclear Systems (ERSN-LMR) from Faculty of Sciences of Tetuan (Morocco) and CENM. The 3-D continuous energy Monte Carlo code MCNP (version 5) was used to develop a versatile and accurate full model of the TRIGA core. The model represents in detailed all components of the core with literally no physical approximation. Continuous energy cross-section data from the more recent nuclear data evaluations (ENDF/B-VI.8, ENDF/B-VII.0, JEFF-3.1, and JENDL-3.3) as well as S( α, β) thermal neutron scattering functions distributed with the MCNP code were used. The cross-section libraries were generated by using the NJOY99 system updated to its more recent patch file "up259". The consistency and accuracy of both the Monte Carlo simulation and neutron transport physics were established by benchmarking the TRIGA experiments. Core excess reactivity, total and integral control rods worth as well as power peaking factors were used in the validation process. Results of calculations are analysed and discussed.

  3. RIA Analysis of Unprotected TRIGA Reactor

    Directory of Open Access Journals (Sweden)

    M.H. Altaf

    2017-07-01

    Full Text Available An RIA (reactivity initiated accident analysis has been carried out for the TRIGA Mark II research reactor considering both step and ramp reactivity ranges within 0.5 % dk/k (< $1 to 2.0 % dk/k (>$2. The insertion time was set at 10 s. Based on the fact that a reactor becomes unprotected if scram does not work at the event of danger, to define unprotected conditions, the time to actuate scram (trip was taken as close to total simulation time. In this long duration of scram inactivity, it is obtained from the present analysis that the reactor remained safe to up to 1.8 % dk/k ($2.57 for step reactivity and 1.99 % dk/k ($2.84 for ramp reactivity. In addition to negative temperature coefficient of reativity, probably the longer time of reactivity insertion keeps TRIGA safe even at larger magnitudes of reactivity during unprotected reactor transients. Coupled point kinetics, neutronics, and thermal hydraulics code EUREKA-2/R has been utilized for this work. It appears that EUREKA-2/RR predicts the sequence of unprotected transient scenario of TRIGA core with good approximation and the results will definitely be helpful for the reactor operators.

  4. Small Angle Neutron Scattering instrument at Malaysian TRIGA reactor

    Energy Technology Data Exchange (ETDEWEB)

    Mohd, Shukri; Kassim, Razali; Mahmood, Zal Uyun [Malaysian Inst. for Nuclear Technology Research (MINT), Bangi, Kajang (Malaysia); Radiman, Shahidan

    1998-10-01

    The TRIGA MARK II Research reactor at the Malaysian Institute for Nuclear Research (MINT) was commissioned in July 1982. Since then various works have been performed to utilise the neutrons produced from this steady state reactor. One of the project involved the Small Angle Neutron Scattering (SANS). (author)

  5. TRIGA International, a new TRIGA fuel fabrication facility at CERCA

    International Nuclear Information System (INIS)

    Harbonnier, G.

    1997-01-01

    At the time when General Atomics expressed its intention to cease fuel fabrication on its site of San Diego, CERCA has been chosen to carry on the fabrication of TRIGA fuel. After negotiations in 1994 and 1995, a partnership 50%/50% was decided and on July 1995, a new company was founded, with the name TRIGA INTERNATIONAL SAS, head office in Paris and fuel fabrication facility at CERCA in Romans. The intent of this presentation is, after a short reminder about TRIGA fuel design and fabrication to describe the new facility with special emphasis on the safety features associated with the modification of existing fabrication buildings. (author)

  6. A TRIGA refueling exercise

    Energy Technology Data Exchange (ETDEWEB)

    McEwen, Michael J [Kansas State University (United States)

    1974-07-01

    In June 1973 the U.S. Atomic Energy Commission offered to assist the Department of Nuclear Engineering staff in refueling the KSU TRIGA Mkll - Nuclear Reactor. The replacement fuel was made available free of charge and a contract was negotiated between the Department of Nuclear Engineering and the A.E.C. to provide for costs incurred during the refueling operation. In addition, the A.E.C. aided in the fuel transfers by providing the names of contacts at the different laboratories and agencies concerned with fuel transfers. Data and numbers relevant to the entire reloading will be available in the short summary. (author)

  7. TRIGA reactor operating experience

    International Nuclear Information System (INIS)

    Anderson, T.V.

    1970-01-01

    The Oregon State TRIGA Reactor (OSTR) has been in operation 3 years. Last August it was upgraded from 250 kW to 1000 kW. This was accomplished with little difficulty. During the 3 years of operation no major problems have been experienced. Most of the problems have been minor in nature and easily corrected. They came from lazy susan (dry bearing), Westronics Recorder (dead spots in the range), The Reg Rod Magnet Lead-in Circuit (a new type lead-in wire that does not require the lead-in cord to coil during rod withdrawal hss been delivered, much better than the original) and other small corrections

  8. Operation and maintenance experience at the General Atomic Company's TRIGA reactor facility at San Diego, California

    International Nuclear Information System (INIS)

    Whittemore, W.L.; Stout, W.A.; Shoptaugh, J.R.; Chesworth, R.H.

    1982-01-01

    Since the startup of the original 250 kW TRIGA Mark I reactor in 1958, General Atomic Company has accumulated nearly 24 years of operation and maintenance experience with this type of reactor. In addition to the nearly 24 years of experience gained on the Mark I, GA has operated the 1.5 MW Advanced Prototype Test Reactor (Mark F) for 22 years and operated a 2 MW below-ground TRIGA Mark III for five years. Information obtained from normal and abnormal operation are presented. (author)

  9. Environmental Assessment: Relocation and storage of TRIGA reg-sign reactor fuel, Hanford Site, Richland, Washington

    International Nuclear Information System (INIS)

    1995-08-01

    In order to allow the shutdown of the Hanford 308 Building in the 300 Area, it is proposed to relocate fuel assemblies (101 irradiated, three unirradiated) from the Mark I TRIGA Reactor storage pool. The irradiated fuel assemblies would be stored in casks in the Interim Storage Area in the Hanford 400 Area; the three unirradiated ones would be transferred to another TRIGA reactor. The relocation is not expected to change the offsite exposure from all Hanford Site 300 and 400 Area operations

  10. Operation experience with the TRIGA reactor Wien 2004

    International Nuclear Information System (INIS)

    Boeck, H.; Villa, M.

    2004-01-01

    The TRIGA Mark-II reactor in Vienna is now in operation for more than 42 years. The average operation time is about 230 days per year with 90 % of this time at nominal power of 250 kW. The remaining 10 % operation time is used for students' training courses at low power level. Pulse operation is rather infrequent with about 5 to 10 pulses per year. The utilization of this facility is excellent, the number of students participating in practical exercises has strongly increased, and also training courses for outside groups such as the IAEA or for the 2004 Eugene Wigner Course are using the reactor, because it is the only TRIGA reactor remaining in Austria. Therefore, there is no need for decommissioning and it is intended to operate it as long as possible into the next decade. Nevertheless, in early 2004 it was decided to prepare a report on a decommissioning procedure for a typical TRIGA Mark II reactor which lists the volumes, the activity and the weight of individual materials such as concrete, aluminium, stainless steel, graphite and others which will accumulate during this process (a summary of possible activated and contaminated materials and the activity of a single TRIGA fuel element as a function of fuel type and decay time in Bq is presented). The status of the reactor (instrumentation, fuel elements, cooling circuit, ventilation system, re-inspection and maintenance program, cost/benefit) is outlined. (nevyjel)

  11. Slovenian Public Libraries in 2010

    Directory of Open Access Journals (Sweden)

    Gorazd Vodeb

    2013-09-01

    Full Text Available ABSTRACTPurpose:  The article presents the 2010 Slovenian public library statistics. Performance indicators are compared to library regulations and standards, and to the goals of the Resolution on the 2008-2011 National Programme for Culture. Opening time, library space and equipment, the size of collections and the number of additions are surveyed. Staff structure and financial data are presented as well as the data about visitors, registered members, loans and other library services.   Methodology/approach:  Data collected via the annual statistical survey of Slovenian public libraries are used. They were collected and published by the Library System Development Centre at the National & University Library.   Results:  Data show the stability of the public library income. The level of resources has been generally increased. The number of loans and visits are still rising whereas the number of registered users is slightly dropping. The extent of digitalisation of library materials has been significantly increased.       Research limitation:  The average value of performance indicators is presented.      Originality/practical implications:  Results can be used for monitoring public library development.

  12. Present and future use of TRIGA reactors in the Federal Republic of Germany

    International Nuclear Information System (INIS)

    Menke, H.; Junker, D.; Krauss, O.

    1986-01-01

    In the Federal Republic of Germany nine research reactors are presently in operation, three of which are TRIGA reactors. These are the TRIGA Mark I reactors at Hannover and Heidelberg with a steady state power of 250 kW and the TRIGA Mark II reactor at Mainz with a steady power of 100 kW and a peak pulsing power of 250 MW. The decommissioning of a number of research reactors, including the TRIGA Mark III reactor at Neuherberg near Munich, is reason enough to think about the present and future use of our reactors. The German TRIGA reactors met a lively interest of scientists, since they went into operation. Presently they are well used especially in biomedical (Hannover, Heidelberg) and basic research (Mainz). In the course of about 20 years of operation the techniques and requirements of experiments changed and consequently the use of the reactors too. Certainly this will be so in the future. But thanks to its versatile experimental facilities, this type of reactor can meet the various experimental demands. So we are looking forward to a good utilisation of our German TRIGA reactors in future and taking into account the low costs for personal, energy and fuel, we are quite confident that they will be in operation still for many years. (author)

  13. Applications of the Dow TRIGA research reactor

    International Nuclear Information System (INIS)

    Kocher, C.W.; Quinn, T.J.; Krueger, D.A.

    1982-01-01

    The Dow TRIGA Mark I reactor is a one-hundred kilowatt nuclear reactor installed by General Atomics using the Torrey Pines reactor console, seventy-five used stainless-steel clad fuel elements and one new aluminium clad fuel element. The reactor is equipped with a forty-position rotating Lazy Susan in the reflector, a pneumatic transfer system with its terminal in the F-ring of the core, and a central thimble which can be used for irradiation of samples in the center of the core or which can be emptied of the shielding water to produce a beam of neutrons and gamma rays in the area atop the pool. Samples can also be irradiated in or near the core. There is no provision for pulsing this TRIGA reactor. The neutron activation analysis program uses the Dow TRIGA reactor as a source of thermal neutrons and a Kaman A711 generator as a source of 14-MeV neutrons. The associated counting equipment includes one Gel(Li) detector and two Nal(Tl) detectors, each using a 100-position sample changer and all interfaced to a Tracor-Northern TN-11 data acquisition and computing system, one Ge(Li) detector and its TN-11 system for the pneumatic transfer system and the beam tube experiments, and two NaKTl)detectors with a TN-4000 system used with the Kaman neutron generator. The activation analysis program gets samples from all parts of the manufacturing and research efforts at Dow: raw materials, intermediates, products, effluents, research samples, samples from customers who use Dow products, and environmental samples. This presentation is devoted to the progress made in the past year on the pneumatic transfer system and the renewed work on prompt gamma-ray spectroscopy including the extensive process of method validation

  14. 4. TRIGA owners' conference. Papers and abstracts

    International Nuclear Information System (INIS)

    1976-01-01

    The Conference covers the following aspects of TRIGA reactors operation: fuel utilization; TRIGA design and startup tests radiation release and unusual occurrences; operating experience; design of experimental facilities and instruments

  15. 3. TRIGA owners' conference. Papers and abstracts

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1974-07-01

    The TRIGA Owners' Conference III was held February 25-27, 1974, in Albuquerque, New Mexico. Seventy representatives were in attendance from 26 TRIGA facilities in the United States, Mexico, Puerto Rico, Indonesia, and from interested government agencies and industrial concerns. The main topics, discussed at the Conference were: TRIGA operating experiences; analytical and experimental methods; limits on effluents release for research reactor; and TRIGA modifications.

  16. 3. TRIGA owners' conference. Papers and abstracts

    International Nuclear Information System (INIS)

    1974-01-01

    The TRIGA Owners' Conference III was held February 25-27, 1974, in Albuquerque, New Mexico. Seventy representatives were in attendance from 26 TRIGA facilities in the United States, Mexico, Puerto Rico, Indonesia, and from interested government agencies and industrial concerns. The main topics, discussed at the Conference were: TRIGA operating experiences; analytical and experimental methods; limits on effluents release for research reactor; and TRIGA modifications

  17. Slovenian and Spanish electricity markets

    International Nuclear Information System (INIS)

    Bregar, Z.

    2004-01-01

    Spanish electricity market has served as a basic model in the construction of the electricity market in Slovenia. However, in the final phase of its development additional solutions were adopted from other European and worldwide electricity markets. The electricity market thus obtained is in some aspects more complex and in others simpler with regard to the original model. This article describes two of the new solutions on the Slovenian electricity market: the introduction of numerous standardized electric energy products (Band, Peak, Off-peak, Hourly power etc.) to be traded on completely separate markets, and the introduction of continuous, real-time type trading on all of them but the hourly market.(author)

  18. Business ethics in the Slovenian economy

    OpenAIRE

    Pučko, Danijel

    2017-01-01

    While taking into account the main concepts of business ethics, the author underlines the importance of the ethical issues in the transition period, identifies the perceived unethical behavior in the Slovenian economy as well as the main approaches to business ethics enhancement in Slovenia. Especially, the attempts to improve business ethical behavior by establishing ethical codes are analysed. This includes the Ethical Code of the Slovenian Managers’ Association, the Code of the Professiona...

  19. Thermal neutron spectrum distribution in TRIGA fuels

    International Nuclear Information System (INIS)

    Gui Ah Auu; Harasawa, Susumu; An, Shigehiro

    1989-01-01

    The dependence of thermal neutron spectrum in TRIGA fuel cell on fuel temperature and TRIGA fuel types were studied using LIBP and THERMOS codes. Some characteristics of the TRIGA fuel including its prompt negative temperature coefficient of reactivity were explained using the results of the study. (author)

  20. European TRIGA owners' conference. Papers and abstracts

    International Nuclear Information System (INIS)

    1970-01-01

    The conference covers the following topics, concerning TRIGA reactors: Experience in the Operation and Maintenance and utilization of TRIGA reactors; reactor upgrading; irradiation facilities; fuel management; air-concentration measurements; nuclear tests; use of TRIGA in nuclear medicine and biology; reactor design, fuel and performance; failures and other research activities

  1. A TRIGA reactor in an industrial laboratory

    International Nuclear Information System (INIS)

    Anders, Oswald U.

    1980-01-01

    The Dow TRIGA Reactor is a well established facility in its industrial environment. It is used extensively for internal Dow projects. The primary use of the TRIGA is as neutron source for NAA. It faces similar technical and organizational challenges as other TRIGA installations and over the years developed its own solutions

  2. Benchmarking criticality analysis of TRIGA fuel storage racks.

    Science.gov (United States)

    Robinson, Matthew Loren; DeBey, Timothy M; Higginbotham, Jack F

    2017-01-01

    A criticality analysis was benchmarked to sub-criticality measurements of the hexagonal fuel storage racks at the United States Geological Survey TRIGA MARK I reactor in Denver. These racks, which hold up to 19 fuel elements each, are arranged at 0.61m (2 feet) spacings around the outer edge of the reactor. A 3-dimensional model was created of the racks using MCNP5, and the model was verified experimentally by comparison to measured subcritical multiplication data collected in an approach to critical loading of two of the racks. The validated model was then used to show that in the extreme condition where the entire circumference of the pool was lined with racks loaded with used fuel the storage array is subcritical with a k value of about 0.71; well below the regulatory limit of 0.8. A model was also constructed of the rectangular 2×10 fuel storage array used in many other TRIGA reactors to validate the technique against the original TRIGA licensing sub-critical analysis performed in 1966. The fuel used in this study was standard 20% enriched (LEU) aluminum or stainless steel clad TRIGA fuel. Copyright © 2016. Published by Elsevier Ltd.

  3. Credible accident analyses for TRIGA and TRIGA-fueled reactors

    International Nuclear Information System (INIS)

    Hawley, S.C.; Kathren, R.L.

    1982-04-01

    Credible accidents were developed and analyzed for TRIGA and TRIGA-fueled reactors. The only potential for offsite exposure appears to be from a fuel-handling accident that, based on highly conservative assumptions, would result in dose equivalents of less than or equal to 1 mrem to the total body from noble gases and less than or equal to 1.2 rem to the thyroid from radioiodines. Credible accidents from excess reactivity insertions, metal-water reactions, lost, misplaced, or inadvertent experiments, core rearrangements, and changes in fuel morphology and ZrH/sub x/ composition are also evaluated, and suggestions for further study provided

  4. CD3 TRIGA users conference

    International Nuclear Information System (INIS)

    2008-01-01

    The Sixteenth European TRIGA Users Conference was held in Pitesti, Romania, on 25-28 September, 2000, under the sponsorship of the Institute for Nuclear Research at Pitesti. The papers which follow in this document are presented in the same order as listed in the Conference Program. All papers which were received for publication (44) have been included. Those papers which were presented but not received for publication are presented in abstract form (4 papers). It was very interesting for the Conference attendees from the West to learn about the large scope of excellent work conducted in Romania, especially at the Institute of Nuclear Research in Pitesti. Similarly, it was fortunate that a large attendance of Romanian researchers (53) from many institutes, universities, and government agencies could attend the Conference and interact with their counterparts from outside Romania. The European TRIGA9 Owners' Group was fortunate to be hosted by the owners and users of the world's largest TRIGA reactor - the 14-MW Romanian research and test reactor. The Opening Session talk was given by Radu Berceanu, Minister of Industries and Commerce. It was followed by the following presentations: R and D - Support for Nuclear Power Development by Ioan Rotaru (General Manager of SNNE); Overview of TRIGA Reactor and other Programs at GENERAL ATOMICS by Junaid Razvi (General Manager TRIGA Reactor at GA); Development strategies connected to National Power and Energy Program by Mircea Ionescu (Director Nuclear Energy Department of M.I.C.); Contribution of INR R and D Programs to Sustain Peaceful and Safe utilization of Nuclear Energy in Romania by Constantin Gheorghiu (Scientific Deputy Director at SCN). A Technical visit to TRIGA Reactor at INR Pitesti took place. Opening Session was followed by five sessions dedicated to the following subjects: Session 1 (8 papers) - TRIGA reactors operation, repair and maintenance; Session 2 (10 papers) - Future developments and future goals of

  5. The TRIGA reactor as chemistry apparatus

    International Nuclear Information System (INIS)

    Miller, G.E.

    1974-01-01

    At the Irvine campus of the University of California, the Mark I, 250 kilowatt TRIGA reactor is used as a regular teaching and research tool by the Department of Chemistry which operates the reactor. Students are introduced to radiochemistry and activation analysis in undergraduate laboratory courses and the relation of nuclear to chemical phenomena is emphasized even in Freshman chemistry. Special peripheral items have been developed for use in graduate and undergraduate research, including a fast pneumatic transfer system for studying short-lived isotopes and arrangements for irradiations at low temperatures. These and other unique features of a purely chemically oriented operation will be discussed and some remarks appended with regard to the merits of a low budget operation. (author)

  6. Effluent releases at the TRIGA reactor facility

    Energy Technology Data Exchange (ETDEWEB)

    Whittemore, W L [General Atomic Co., San Diego, CA (United States)

    1974-07-01

    The principal effluent from the operating TRIGA reactors in our facility is argon-41. As monitored by a recording gas and particulate stack monitor, the values shown in the table, the Mark III operating 24 hours per day for very long periods produced the largest amount of radioactive argon. The quantity of 23.7 Ci A-41 when diluted by the normal reactor room ventilation system corresponded to 1.45 x 10{sup -6} {mu}Ci/cc. As diluted in the roof stack stream and the reactor building wake, the concentration immediately outside the reactor building was 25% MPC for an unrestricted area. The continued dilution of this effluent resulted in a concentration of a few percent MPC at the site boundary (unrestricted area) 350 meters from the reactor. (author)

  7. The TRIGA reactor as chemistry apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Miller, G E [University of California, Irvine (United States)

    1974-07-01

    At the Irvine campus of the University of California, the Mark I, 250 kilowatt TRIGA reactor is used as a regular teaching and research tool by the Department of Chemistry which operates the reactor. Students are introduced to radiochemistry and activation analysis in undergraduate laboratory courses and the relation of nuclear to chemical phenomena is emphasized even in Freshman chemistry. Special peripheral items have been developed for use in graduate and undergraduate research, including a fast pneumatic transfer system for studying short-lived isotopes and arrangements for irradiations at low temperatures. These and other unique features of a purely chemically oriented operation will be discussed and some remarks appended with regard to the merits of a low budget operation. (author)

  8. TRIGA out of core gamma irradiation facility

    International Nuclear Information System (INIS)

    Rant, J.; Pregl, G.

    1988-01-01

    A possibility to irradiate extended objects in a gamma field inside the shielding water tank and above the core of operating TRIGA Mark II Reactor has been investigated. The irradiation cask is shielded with Cd cover to filter out thermal neutrons. The dose rate of the gamma field strongly depends on the distance of the irradiation position above the core. At 25 cm above the core, the gamma dose rate is 2.2 Gy/s and epithermal neutron flux is ∼ 8.10 6 ncm -2 s -1 ∼ 3 as measured by TLD (CaF 2 : Mn) dosimeters and Au foils respectively. Tentative applications of the gamma irradiation facility are in the studies of radiation induced accelerated aging and within the Nuclear Power Plant Equipment Qualification Program (EQP). A complete characterization of the neutron spectrum and optimization of the 7 radiation field within the cask has still to be performed. (author)

  9. Slovenian diasporic literature in Canada and Ted Kramolc

    Directory of Open Access Journals (Sweden)

    Igor Maver

    2014-12-01

    Full Text Available The article analyzes the work and especially the novels by the Canadian writer of Slovenian descent, Ted Kramolc. It places him within the context of other diasporic literary authors in Canada as well as the Slovenian cultural space and discusses the critical response to his work, particularly in the period after Slovenian independence.

  10. PA/SA for Slovenian LILW repository

    International Nuclear Information System (INIS)

    Zeleznik, N.; Mele, I.

    1999-01-01

    The RAO Agency started with a new site selection procedure in 1996. As part of the preparational work for the new disposal facility, tools for assessment of the specific disposal concept influence on the environment and human has to be developed. Therefore the Slovenian assessment team that has been organized, joined the IAEAs ISAM programme, in which different approaches to performance and safety assessment were applied to safety cases. As part of the ISAM individual (national) safety cases. The RAO Agency, together with other Slovenian Inst.ions, performed the preliminary performance assessment of the Slovenian LILW repository for generic site location. The method and the results of the safety case are presented in this paper.(author)

  11. PUSPATI Triga Reactor pulsing parameters

    Energy Technology Data Exchange (ETDEWEB)

    Auu, Gui Ah; Abu, Puad Haji; Yunus, Yaziz [PUSPATI, Selangor (Malaysia)

    1984-06-01

    The pulsing experiment was carried out as part of the commissioning activites of PUSPATI TRIGA Reactor (PTR). Several parameters of PTR were deduced from the experiment. It was found that the maximum temperature of the fuel was far below the safety limit when the maximum allowable positive reactivity of $3.00 was inserted into the core. The peak power achieved was 1354 Mw.

  12. Isothermal temperature reactivity coefficient measurement in TRIGA reactor

    International Nuclear Information System (INIS)

    Zagar, T.; Ravnik, M.; Trkov, A.

    2002-01-01

    Direct measurement of an isothermal temperature reactivity coefficient at room temperatures in TRIGA Mark II research reactor at Jozef Stefan Institute in Ljubljana is presented. Temperature reactivity coefficient was measured in the temperature range between 15 o C and 25 o C. All reactivity measurements were performed at almost zero reactor power to reduce or completely eliminate nuclear heating. Slow and steady temperature decrease was controlled using the reactor tank cooling system. In this way the temperatures of fuel, of moderator and of coolant were kept in equilibrium throughout the measurements. It was found out that TRIGA reactor core loaded with standard fuel elements with stainless steel cladding has small positive isothermal temperature reactivity coefficient in this temperature range.(author)

  13. Thermal hydraulic analysis of the IPR-R1 TRIGA reactor; Analise termo-hidraulica do reator TRIGA IPR-R1

    Energy Technology Data Exchange (ETDEWEB)

    Veloso, Marcelo Antonio [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN), Belo Horizonte, MG (Brazil); Fortini, Maria Auxiliadora [Minas Gerais Univ., Belo Horizonte, MG (Brazil). Dept. de Engenharia Nuclear

    2002-07-01

    The subchannel approach, normally employed for the analysis of power reactor cores that work under forced convection, have been used for the thermal hydraulic evaluation of a TRIGA Mark I reactor, named IPR-R1, at 250 kW power level. This was accomplished by using the PANTERA-1P subchannel code, which has been conveniently adapted to the characteristics of natural convection of TRIGA reactors. The analysis of results indicates that the steady state operation of IPR-R1 at 250 kW do not imply risks to installations, workers and public. (author)

  14. Slovenian Pre-Service Teachers' Prototype Biography

    Science.gov (United States)

    Lipovec, Alenka; Antolin, Darja

    2014-01-01

    In this article we apply narrative methodology to the study of pre-service elementary teachers' school-time memories connected to mathematics education. In the first phase of our empirical study we asked 214 Slovenian pre-service teachers to write their mathematical autobiographies. On the basis of the mathematical autobiographies we constructed a…

  15. Business ethics in the Slovenian economy

    Directory of Open Access Journals (Sweden)

    Danijel Pučko

    2000-01-01

    Full Text Available While taking into account the main concepts of business ethics, the author underlines the importance of the ethical issues in the transition period, identifies the perceived unethical behavior in the Slovenian economy as well as the main approaches to business ethics enhancement in Slovenia. Especially, the attempts to improve business ethical behavior by establishing ethical codes are analysed. This includes the Ethical Code of the Slovenian Managers’ Association, the Code of the Professional Ethics of the Accountants and the Code of the Professional Ethics of the Controllers in Slovenia, as well as some other ethical codes. The courses, workshops and seminars in the field of the business ethics are surveyed as well as the problems in teaching business ethics and empirically researching the field in Slovenia. The role of the media in enhancing business ethics in the country is analysed too. The last part of the article is dedicated to the identification of the prevailing values and attitudes of the Slovenian top managers and of the younger Slovenian managers. Differences and similarities are shown the respect to the results of some foreign research findings. Finally, there are a few conclusions regarding the needed future actions for further enhancement of business ethical behavior in Slovenia.

  16. Increasing TRIGA fuel lifetime with 12 wt.% U TRIGA fuel

    Energy Technology Data Exchange (ETDEWEB)

    Naughton, W F; Cenko, M J; Levine, S H; Witzig, W F [Pennsylvania State University (United States)

    1974-07-01

    In-core fuel management studies have been performed for the Penn State Breazeale Reactor (PSBR) wherein 12 wt % U fuel elements are used to replace the standard 8.5 wt % U TRIGA fuel. The core configuration used to develop a calculational model was a 90-element hexagonal array, which is representative of the PSBR core, and consists of five hexagonal rings surrounding a central thimble containing water. The technique employed for refueling the core fully loaded with 8.5 wt % U fuel involves replacing 8.5 wt % U fuel with 12 wt % U fuel using an in-out reloading scheme. A batch reload consists of 6 new 12 wt % U fuel elements. Placing the 12 wt % U fuel in the B ring produces fuel temperatures ({approx}450 {sup o}C) that are well below the 800{sup o}C maximum limitation when the PSBR is operating at its maximum allowed power of 1 Megawatt. The advantages of using new 12 wt % U fuel to replace the burned up 8.5 wt % U fuel in the B ring over refueling strictly with 8.5 wt % U-Zr TRIGA fuel are clearly delineated in Table 1 where cost calculations used the General Atomic pre-1972 prices for TRIGA fuel, i.e., $1500 and $1650 for an 8.5 and 12 wt % U fuel element, respectively. Experimental results obtained to date utilizing the 12 wt % U fuel elements agree with the computed results. (author)

  17. TRIGA forced shutdowns analysis

    International Nuclear Information System (INIS)

    Negut, Gheorghe; Laslau, Florica

    2008-01-01

    The need for improving the operation leads us to use new methods and strategies. Probabilistic safety assessments and statistical analysis provide insights useful for our reactor operation. This paper is dedicated to analysis of the forced shutdowns during the first reactor operation period, between 1980 to 1989. A forced shutdown data base was designed using data on forced shutdowns collected from the reactor operation logbooks. In order to sort out the forced shutdowns the records have the following fields: - current number, date, equipment failed, failure type (M for mechanical, E for electrical, D for irradiation device, U for human factor failure; - scram mode, SE for external scram, failure of reactor cooling circuits and/or irradiation devices, SR for reactor scram, exceeding of reactor nuclear parameters, SB for reactor scram by control rod drop, SM for manual scram required by the abnormal reactor status; - scram cause, giving more information on the forced shutdown. This data base was processed using DBase III. The data processing techniques are presented. To sort out the data, one of the criteria was the number of scrams per year, failure type, scram mode, etc. There are presented yearly scrams, total operation time in hours, total unavailable time, median unavailable time period, reactor availability A. There are given the formulae used to calculate the reactor operational parameters. There are shown the scrams per year in the 1980 to 1989 period, the reactor operation time per year, the reactor shutdown time per year and the operating time versus down time per year. Total number of scrams in the covered period was 643 which caused a reactor down time of 4282.25 hours. In a table the scrams as sorted on the failure type is shown. Summarising, this study emphasized some problems and difficulties which occurred during the TRIGA reactor operation at Pitesti. One main difficulty in creating this data base was the unstandardized scram record mode. Some times

  18. PUSPATI Triga Reactor pulsing parameters

    International Nuclear Information System (INIS)

    Gui Ah Auu; Puad Haji Abu; Yaziz Yunus

    1984-01-01

    The pulsing experiment was carried out as part of the commissioning activites of PUSPATI TRIGA Reactor (PTR). Several parameters of PTR were deduced from the experiment. It was found that the maximum temperature of the fuel was far below the safety limit when the maximum allowable positive reactivity of $3.00 was inserted into the core. The peak power achieved was 1354 Mw. (author)

  19. Extension of TRIGA reactor capabilities

    International Nuclear Information System (INIS)

    Gietzen, A.J.

    1980-01-01

    The first TRIGA reactor went into operation at 10 kW about 22 years ago. Since that time 55 TRIGAs have been put into operation including steady-state powers up to 14,000 kW and pulsing reactors that pulse to 20,000,000 kW. Five more are under construction and a proposal will soon be submitted for a reactor of 25,000 kW. Along with these increases in power levels (and the corresponding fluxes) the experimental facilities have also been expanded. In addition to the installation of new TRIGA reactors with enhanced capabilities many of the older reactors have been modified and upgraded. Also, a number of reactors originally fueled with plate fuel were converted to TRIGA fuel to take advantage of the improved technical and safety characteristics, including the ability for pulsed operation. In order to accommodate increased power and performance the fuel has undergone considerable evolution. Most of the changes have been in the geometry, enrichment and cladding material. However, more recently further development on the UZrH alloy has been carried out to extend the uranium content up to 45% by weight. This increased U content is necessary to allow the use of less than 20% enrichment in the higher powered reactors while maintaining longer core lifetime. The instrumentation and control system has undergone remarkable improvement as the electronics technology has evolved so rapidly in the last two decades. The information display and the circuitry logic has also undergone improvements for enhanced ease of operation and safety. (author)

  20. TRIGA reactor health physics considerations

    International Nuclear Information System (INIS)

    Johnson, A.G.

    1970-01-01

    The factors influencing the complexity of a TRIGA health physics program are discussed in details in order to serve as a basis for later consideration of various specific aspects of a typical TRIGA health physics program. The health physics program must be able to provide adequate assistance, control, and safety for individuals ranging from the inexperienced student to the experienced postgraduate researcher. Some of the major aspects discussed are: effluent release and control; reactor area air monitoring; area monitoring; adjacent facilities monitoring; portable instrumentation, personnel monitoring. TRIGA reactors have not been associated with many significant occurrences in the area of health physics, although some operational occurrences have had health physics implications. One specific occurrence at OSU is described involving the detection of non-fission-product radioactive particulates by the continuous air monitor on the reactor top. The studies of this particular situation indicate that most of the particulate activity is coming from the rotating rack and exhausting to the reactor top through the rotating rack loading tube

  1. Thermal hydraulic analysis of the IPR-R1 TRIGA reactor

    International Nuclear Information System (INIS)

    Veloso, Marcelo Antonio; Fortini, Maria Auxiliadora

    2002-01-01

    The subchannel approach, normally employed for the analysis of power reactor cores that work under forced convection, have been used for the thermal hydraulic evaluation of a TRIGA Mark I reactor, named IPR-R1, at 250 kW power level. This was accomplished by using the PANTERA-1P subchannel code, which has been conveniently adapted to the characteristics of natural convection of TRIGA reactors. The analysis of results indicates that the steady state operation of IPR-R1 at 250 kW do not imply risks to installations, workers and public. (author)

  2. TRIGA reactor owners' seminar. Papers and abstracts

    International Nuclear Information System (INIS)

    1970-01-01

    The TRIGA Reactor Owners' Conference was planned with the aim of bringing together a group of persons interested in the ownership and operation of TRIGA reactors in the hope that an interchange of viewpoints, information, and experience would prove of mutual benefit

  3. Fuel element burnup determination in HEU-LEU mixed TRIGA research reactor core

    International Nuclear Information System (INIS)

    Zagar, Tomaz; Ravnik, Matjaz

    2000-01-01

    This paper presents the results of a burnup calculations and burnup measurements for TRIGA FLIP HEU fuel elements and standard TRIGA LEU fuel elements used simultaneously in small TRIGA Mark II research reactor in Ljubljana, Slovenija. The fuel element burnup for approximately 15 years of operation was calculated with two different in house computer codes TRIGAP and TRIGLAV (both codes are available at OECD NEA Data Bank). The calculation is performed in one-dimensional radial geometry in TRIGAP and in two-dimensional (r,φ) geometry in TRIGLAV. Inter-comparison of results shows important influence of in-core water gaps, irradiation channels and mixed rings on burnup calculation accuracy. Burnup of 5 HEU and 27 LEU fuel elements was also measured with reactivity method. Measured and calculated burnup values are inter-compared for these elements (author)

  4. A selection of Slovenian literary heroes for the preschool period

    OpenAIRE

    Dolinar, Ana

    2014-01-01

    In preschools, Slovenian literary heroes are being displaced by foreign fantastic heroes that impress children via cartoons, magazines and video games. Slovenian heroes are an important part of our culture and can act as companions of sorts within citizenship education of youngsters. This thesis should serve as a promotion of Slovenian literary heroes for children of all ages, beginning with the preschool period. The thesis defines the selection criterion of characters; it introduces their st...

  5. The System For Co-Reference Resolution For Slovenian Texts Analysis and Possibilities of its Use

    Directory of Open Access Journals (Sweden)

    Peter Holozan

    2015-10-01

    Full Text Available Co-reference resolution is an important part of language technologies, but has not yet been developed for Slovenian. There are various types of co-references and the paper focuses on anaphora resolution of personal pronouns. Seven methods, used in combination, were used; the most important one is based on activation. First results are promising, but for more extensive evaluation, Slovenian corpus with marked examples is needed. Co-reference resolution was used in the question answering system Crammer, which can, as a result, answer more questions than before, because it can replace personal pronouns. At the same time, some other improvement were added to Crammer, e.g. answering to individual words and phrases and answering to declarative sentences. Added was also generation of long answers to questions with interrogative particles. Co-reference resolution also improved working of Presis machine translation, especially for determining of gender of pronouns and for disambiguation of attributive subordinate clauses.

  6. Two dimensional burn-up calculation of TRIGA core

    International Nuclear Information System (INIS)

    Persic, A.; Ravnik, M.; Slavic, S.

    1996-01-01

    TRIGLAV is a new computer program for burn-up calculation of mixed core of research reactors. The code is based on diffusion model in two dimensions and iterative procedure is applied for its solution. The material data used in the model are calculated with the transport program WIMS. In regard to fission density distribution and energy produced by the reactor the burn-up increment of fuel elements is determined. In this paper the calculation model of diffusion constants and burn-up calculation are described and some results of calculations for TRIGA MARK II reactor are presented. (author)

  7. Holocaust Denial among Slovenian Secondary School Pupils

    Directory of Open Access Journals (Sweden)

    Maša Pavlič

    2015-06-01

    Full Text Available The article presents tendencies of Holocaust denial among secondary school pupils in Slovenia. It focuses on research implemented in January 2012, in which 400 Slovenian secondary school pupils were included. In spite of the assumption that Holocaust denial amongst the youth in Slovenia already exists, we also assumed that a degree of Holocaust denial amongs Slovenian pupils is lower that amongst their peers in other EU countries. Research also inquired about the level of anti-Semitism in conjunction with Holocaust denial. The research project confirmed that students on lower levels of high school education and with less history and sociology lessons in curriculum are more receptive for the Holocaust denial and anti-Semitism is more present in this demographic. The level of Holocaust denial amongst secondary school pupils is not negligible; it suggests that this topic should be more thoroughly discussed in secondary schools.

  8. Information support for Slovenian Cycling Federation

    OpenAIRE

    Mahkovec, Tine

    2011-01-01

    Abstract Following work presents development of information system that will support Slovenian Cycling Federation. In the first part, work introduces the federation, its key processes, people involved and describes main tools, technologies and approaches used in this work. In the main part, work describes main activities of object oriented development of information system, which includes analysis, requirements definition and architecture planning. Implementation and testing was left ...

  9. Stemming of Slovenian library science texts

    Directory of Open Access Journals (Sweden)

    Polona Vilar

    2002-01-01

    Full Text Available The theme of the article is the preparation of a stemming algorithm for Slovenian library science texts. The procedure consisted of three phases: learning, testing and evaluation.The preparation of the optimal stemmer for Slovenian texts from the field of library science is presented, its testing and comparison with two other stemmers for the Slovenian language: the Popovič stemmer and the Generic stemmer. A corpus of 790.000 words from the field of library science was used for learning. Lists of stems, word endings and stop-words were built. In the testing phase, the component parts of the algorithm were tested on an additional corpus of 167.000 words. In the evaluation phase, a comparison of the three stemmers processing the same word corpus was made. The results of each stemmer were compared with an intellectually prepared control result of the stemming of the corpus. It consisted of groups of semantically connected words with no errors. Understemming was especially monitored – the number of stems for semantically connected words, produced by an algorithm. The results were statistically processed with the Kruskal-Wallis test. The Optimal stemmer produced the best results.It matched best with the reference results and also gave the smallest number of stems for one semantic meaning. The Popovič stemmer followed closely. The Generic stemmer proved to be the least accurate. The procedures described in the thesis can represent a platform for the development of the tools for automatic indexing and retrieval for library science texts in Slovenian language.

  10. Preparations for decommissioning the TRIGA Mark III Berkeley Research Reactor

    International Nuclear Information System (INIS)

    Denton, Michael M.; Lim, Tek. H.

    1988-01-01

    On December 20, 1986 the chancellor of UC Berkeley announced his decision to decommission the 20 year old Berkeley Research Reactor citing as principal reasons a decline in use and a need to erect a new computer science building over the reactor's site. In order to meet the University's construction timetable for the new building, the reactor staff together with other units of the campus administration have initiated a program to remove the reactor structure and clear the room for unlicensed use as expediently as possible. Due to the sequence of events which must occur in a limited amount of time, the University adopted a policy to contract out as much of the work as possible, including generation of the defueling and decommissioning plans.The first physical step in the decommissioning project is the removal of the irradiated fuel. This task is largely contracted out to a commercial firm with experience in the transport of radioactive materials and reactor fuel. As suggested by the NRC, the reactor will be defueled under the current operating license. This requires that all fuel must be off-site before the DP can be approved. Therefore any delay in defueling in-turn delays the decommissioning. The NRC has given no commitment or date for completion of their review. Informal discussion with NRC project managers and the experience from other facilities indicate that the review process will take between six and nine months

  11. The evaluation of research reactor TRIGA MARK II safety

    International Nuclear Information System (INIS)

    Jordan, R.; Kozuh, M.; Mavko, B.

    1994-01-01

    In the paper the Probabilistic Safety Analysis (PSA) of a research reactor is described. Five different initiating events were selected and analyzed with the use of event trees. Seven reactor systems were modeled with fault trees. Three groups of radiation releases were introduced - Success, Reactor-Hall, Environment - and their frequencies were estimated. The importance factors of initiating events, human errors and basic events were calculated regarding the consequence groups. (author)

  12. Calculation of Kinetic Parameters of TRIGA Reactor

    International Nuclear Information System (INIS)

    Snoj, Luka; Kavcic, Andrej; Zerovnik, Gasper; Ravnik, Matjaz

    2008-01-01

    Modern Monte Carlo transport codes in combination of fast computer clusters enable very accurate calculations of the most important reactor kinetic parameters. Such are the effective delayed neutron fraction, β eff , and mean neutron generation time, Λ. We calculated the β eff and Λ for various realistic and hypothetical annular TRIGA Mark II cores with different types and amount of fuel. It can be observed that the effective delayed neutron fraction strongly depends on the number of fuel elements in the core or on the core size. E.g., for 12 wt. % uranium standard fuel with 20 % enrichment, β eff varies from 0.0080 for a small core (43 fuel rods) to 0.0075 for a full core (90 fuel rods). It is interesting to note that calculated value of β eff strongly depends also on the delayed neutron nuclear data set used in calculations. The prompt neutron life-time mainly depends on the amount (due to either content or enrichment) of 235 U in the fuel as it is approximately inversely proportional to the average absorption cross-section of the fuel. E.g., it varies from 28 μs for 30 wt. % uranium content fuelled core to 48 μs for 8.5 wt. % uranium content LEU fuelled core. The results are especially important for pulse mode operation and analysis of the pulses. (authors)

  13. Research work at the TRIGA Mainz reactor

    International Nuclear Information System (INIS)

    Trautmann, Norbert

    1976-01-01

    In the last two years the research activities at the TRIGA Mark II reactor in Mainz have mainly been concentrated on the investigation of short- lived nuclides of medium mass number produced by thermal-neutron induced fission of 235 U and other fissile materials. For the identification of these nuclides and for detailed studies of their properties rapid chemical separation procedures in combination with high-resolution gamma-ray and neutron spectroscopy as well as mass-separated samples have been used. Fast, discontinuous separation techniques are illustrated by a procedure for technetium. Continuous separation methods from aqueous solutions and in the gas phase, accomplished by combining a gas jet recoil transport system with an on-line operating solvent extraction technique and a thermo- chromatographic method, are presented. The application of such procedures to decay scheme and delayed neutron studies is demonstrated by a few examples. The experimental set-up and the method for nuclear spin - and magnetic moment measurements on alkali isotopes far from the region of beta-stability applying the nuclear radiation detected optical pumping technique to mass- separated samples of neutron-rich alkali nuclides are briefly described. (author)

  14. Radioactivity of spent TRIGA fuel

    Energy Technology Data Exchange (ETDEWEB)

    Usang, M. D., E-mail: mark-dennis@nuclearmalaysia.gov.my; Nabil, A. R. A.; Alfred, S. L.; Hamzah, N. S.; Abi, M. J. B.; Rawi, M. Z. M.; Abu, M. P. [Reactor Department, Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia)

    2015-04-29

    Some of the oldest TRIGA fuel in the Malaysian Reaktor TRIGA PUSPATI (RTP) is approaching the limit of its end of life with burn-up of around 20%. Hence it is prudent for us to start planning on the replacement of the fuel in the reactor and other derivative activities associated with it. In this regard, we need to understand all of the risk associated with such operation and one of them is to predict the radioactivity of the fuel, so as to estimate the safety of our working conditions. The radioactivity of several fuels are measured and compared with simulation results to confirm the burnup levels of the selected fuels. The radioactivity measurement are conducted inside the water tank to reduce the risk of exposure and in this case the detector wrapped in plastics are lowered under water. In nuclear power plant, the general practice was to continuously burn the fuel. In research reactor, most operations are based on the immediate needs of the reactor and our RTP for example operate periodically. By integrating the burnup contribution for each core configuration, we simplify the simulation of burn up for each core configuration. Our results for two (2) fuel however indicates that the dose from simulation underestimate the actual dose from our measurements. Several postulates are investigated but the underlying reason remain inconclusive.

  15. Radioactivity of spent TRIGA fuel

    International Nuclear Information System (INIS)

    Usang, M. D.; Nabil, A. R. A.; Alfred, S. L.; Hamzah, N. S.; Abi, M. J. B.; Rawi, M. Z. M.; Abu, M. P.

    2015-01-01

    Some of the oldest TRIGA fuel in the Malaysian Reaktor TRIGA PUSPATI (RTP) is approaching the limit of its end of life with burn-up of around 20%. Hence it is prudent for us to start planning on the replacement of the fuel in the reactor and other derivative activities associated with it. In this regard, we need to understand all of the risk associated with such operation and one of them is to predict the radioactivity of the fuel, so as to estimate the safety of our working conditions. The radioactivity of several fuels are measured and compared with simulation results to confirm the burnup levels of the selected fuels. The radioactivity measurement are conducted inside the water tank to reduce the risk of exposure and in this case the detector wrapped in plastics are lowered under water. In nuclear power plant, the general practice was to continuously burn the fuel. In research reactor, most operations are based on the immediate needs of the reactor and our RTP for example operate periodically. By integrating the burnup contribution for each core configuration, we simplify the simulation of burn up for each core configuration. Our results for two (2) fuel however indicates that the dose from simulation underestimate the actual dose from our measurements. Several postulates are investigated but the underlying reason remain inconclusive

  16. The use of the Job Satisfaction Scale in Slovenian companies

    Directory of Open Access Journals (Sweden)

    Vid Pogačnik

    2000-12-01

    Full Text Available The Job Satisfaction Scale was applied to a representative sample of 5.094 employees in 54 Slovenian companies. Appropriate metric characteristics and the possibility of insight into global job satisfaction as well as into its 15 aspects, speak for usefulness of this instrument. The quality of work life in Slovenian companies is also briefly described.

  17. Use of TRIGA flip fuel for improved in-core irradiations

    Energy Technology Data Exchange (ETDEWEB)

    Whittemore, W L [General Atomic Co., San Diego, CA (United States)

    1974-07-01

    Use of standard TRIGA fuel (20% enriched uranium) in a reactor provides a suitable facility for in-core irradiations. However, large numbers of in-core samples irradiated for long periods (many months) can be handled more economically with a TRIGA loaded with FLIP fuel. As an example, ten or more in-core thermionic devices (each worth 50 to 80 cents with respect to a water-filled position) were irradiated in the Mark III TRIGA at General Atomic Company for 18 months with only a modest change in excess reactivity due to core burnup. A core loading of FLIP fuel has been added to the General Atomic Mark F reactor in order to provide numerous in-core irradiation sites for the production of radioisotopes. Since the worth of a 500-gram sample of a molybdenum compound (used for the production of {sup 99}Mo) is about 25 to 50 cents with respect to a water-filled position, use of a FLIP- TRIGA core will permit the irradiation of more than 5 kilograms of a molybdenum compound. A procedure is under development for the production of {sup 99}Mo with relatively high specific activity. Several techniques to concentrate {sup 99}Mo have been tested experimentally. The results will be reported. (author)

  18. Efficiency and regulation of the Slovenian electricity distribution companies

    International Nuclear Information System (INIS)

    Filippini, Massimo; Hrovatin, Nevenka; Zoric, Jelena

    2004-01-01

    The Slovenian Energy Law, adopted in 1999, has opened the internal market to competition up to 64% of the final consumption. The opening of the internal market to foreign competition is envisaged for 2003. With regard to the methodology of price regulation, the Energy Law introduces the 'price-cap' regulation, which aims to give firms incentive for cost reduction. To provide information for effective price regulation, we estimated a cost frontier function on a sample of Slovenian electricity distribution utilities over the 1991-2000 period. The estimated efficient frontier could be used by Slovenian regulatory agency as a benchmark to regulate network access prices. Our results show that Slovenian distribution companies are cost inefficient. We have also proved the presence of increasing returns to scale with most utilities not achieving the minimum efficient scale. Thus, the Slovenian regulatory authority should consider how to induce mergers of small electricity distribution utilities into larger units

  19. 5. TRIGA owners' conference. Papers and abstracts

    International Nuclear Information System (INIS)

    1977-01-01

    The main topics of the Conference are: research reactor licensing and regulation; standards and public relations programs; operating problems and operating programs of research reactors; security requirements for TRIGA reactors

  20. Oregon State University TRIGA Reactor annual report

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, T.V.; Johnson, A.G.; Bennett, S.L.; Ringle, J.C.

    1979-08-31

    The use of the Oregon State University TRIGA Reactor during the year ending June 30, 1979, is summarized. Environmental and radiation protection data related to reactor operation and effluents are included.

  1. Oregon State University TRIGA Reactor annual report

    International Nuclear Information System (INIS)

    Anderson, T.V.; Johnson, A.G.; Bennett, S.L.; Ringle, J.C.

    1979-01-01

    The use of the Oregon State University TRIGA Reactor during the year ending June 30, 1979, is summarized. Environmental and radiation protection data related to reactor operation and effluents are included

  2. Opportunities for TRIGA reactors in neutron radiography

    International Nuclear Information System (INIS)

    Barton, John P.

    1978-01-01

    In this country the two most recent installations of TRIGA reactors have both been for neutron radiography, one at HEDL and the other at ANL. Meanwhile, a major portion of the commercial neutron radiography is performed on a TRIGA fueled reactor at Aerotest. Each of these installations has different primary objectives and some comparative observations can be drawn. Another interesting comparison is between the TRIGA reactors for neutron radiography and other small reactors that are being installed for this purpose such as the MIRENE slow pulse reactors in France, a U-233 fueled reactor for neutron radiography in India and the L88 solution reactor in Denmark. At Monsanto Laboratory, in Ohio, a subcritical reactor based on MTR-type fuel has recently been purchased for neutron radiography. Such systems, when driven by a Van de Graaff neutron source, will be compared with the standard TRIGA reactor. Future demands on TRIGA or competitive systems for neutron radiography are likely to include the pulsing capability of the reactor, and also the extraction of cold neutron beams and resonance energy beams. Experiments recently performed on the Oregon State TRIGA Reactor provide information in each of these categories. A point of particular current concern is a comparison made between the resonance energy beam intensity extracted from the edge of the TRIGA core and from a slot which penetrated to the center of the TREAT reactor. These results indicate that by using such slots on a TRIGA, resonance energy intensities could be extracted that are much higher than previously predicted. (author)

  3. 4. European conference of TRIGA users. Papers and abstracts

    International Nuclear Information System (INIS)

    1976-01-01

    The main topics of the Conference are: TRIGA operating experience special experimental and maintenance experience; activation analysis and isotope production; research programs; special instrumentation testing and other TRIGA specific topics

  4. 4. European conference of TRIGA users. Papers and abstracts

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-07-01

    The main topics of the Conference are: TRIGA operating experience special experimental and maintenance experience; activation analysis and isotope production; research programs; special instrumentation testing and other TRIGA specific topics.

  5. 5. European conference of TRIGA users. Papers and abstracts

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-07-01

    The main conference topics were: Operation and maintenance experience of the TRIGA reactors; Development of new Low Enrichment Fuels (LEU); Dose assessments noble gas releases; Radiation protection and dosimetry measurements; Research reactors programs and experiments; and Application of TRIGA reactors.

  6. 5. European conference of TRIGA users. Papers and abstracts

    International Nuclear Information System (INIS)

    1978-01-01

    The main conference topics were: Operation and maintenance experience of the TRIGA reactors; Development of new Low Enrichment Fuels (LEU); Dose assessments noble gas releases; Radiation protection and dosimetry measurements; Research reactors programs and experiments; and Application of TRIGA reactors

  7. CONTEMPORARY SLOVENIAN TIMBER ARCHITECTURE INTERNATIONAL RECOGNIZED

    Directory of Open Access Journals (Sweden)

    Manja Kitek Kuzman

    2014-12-01

    Full Text Available The book presents Slovenia' s contemporary timber architecture. Thanks to its abundant forests, Slovenia has preserved the tradition of wood construction. As much as 60% of its surface is covered by forests. Slovenia is also the third most forested country in Europe. The high share of forest-covered surface allows for a sustainable production of high-quality wood. In the past, wood was used primarily in the construction of farm buildings, but now timber architecture is used for everything from residences and office buildings to public buildings such as community centres and schools. Timber construction is becoming increasingly popular. Apart from larger companies taking this approach, a great number of wooden houses have sprung up, built either on personal initiative or with the support of carpenter workshops. Slovenian timber architecture has taken a new approach to environmental and energy-efficiency problems and received great international recognition. The book discusses over fifty projects built over a ten-year period, and includes descriptions, photographs, and plans. The projects include residential areas, administration, and office, as well as tourist, educational, and industrial buildings. Timber architecture is presented as an integral part of the Slovenian landscape. The monograph will be useful to designers and future experts in their planning of optimal timber buildings and will highlight the main benefits of using timber construction.

  8. Leadership Competences in Slovenian Health Care

    Science.gov (United States)

    KOVAČIČ, Helena; RUS, Andrej

    2015-01-01

    Background Leadership competences play an important role for the success of effective leadership. The purpose of this study was to examine leadership competences of managers in the healthcare sector in Slovenia. Methods Data were collected in 2008. The research included 265 employees in healthcare and 267 business managers. Respondents assessed their level of 16 leadership relevant competences on a 7-point Likert-type scale. Results Test of differences between competences and leader position of health care professionals yielded statistically significant differences between leader and non-leader positions. Leaders gave strongest emphasis to interpersonal and informational competences, while regarding decision making competences, the differences between leaders and other employees are not that significant. When comparing competences of healthcare managers with those of business managers, results show that healthcare managers tend to give weaker emphasis to competences related to all three managerial roles than business managers. Conclusions The study showed that in Slovenian health care, leaders distinguish themselves from other employees in some leadership competences. In addition, all three dimensions of leadership competences significantly distinguished the group of healthcare managers from the business managers, which indicates a serious lag in leadership competences among leaders in Slovenian healthcare. PMID:27646617

  9. Leadership Competences in Slovenian Health Care.

    Science.gov (United States)

    Kovačič, Helena; Rus, Andrej

    2015-03-01

    Leadership competences play an important role for the success of effective leadership. The purpose of this study was to examine leadership competences of managers in the healthcare sector in Slovenia. Data were collected in 2008. The research included 265 employees in healthcare and 267 business managers. Respondents assessed their level of 16 leadership relevant competences on a 7-point Likert-type scale. Test of differences between competences and leader position of health care professionals yielded statistically significant differences between leader and non-leader positions. Leaders gave strongest emphasis to interpersonal and informational competences, while regarding decision making competences, the differences between leaders and other employees are not that significant. When comparing competences of healthcare managers with those of business managers, results show that healthcare managers tend to give weaker emphasis to competences related to all three managerial roles than business managers. The study showed that in Slovenian health care, leaders distinguish themselves from other employees in some leadership competences. In addition, all three dimensions of leadership competences significantly distinguished the group of healthcare managers from the business managers, which indicates a serious lag in leadership competences among leaders in Slovenian healthcare.

  10. Conceptual design of a clinical BNCT beam in an adjacent dry cell of the Jozef Stefan Institute TRIGA reactor

    NARCIS (Netherlands)

    Maucec, M

    The MCNP4B Monte Carlo transport code is used in a feasibility study of the epithermal neutron boron neutron capture therapy facility in the thermalizing column of the 250-kW TRIGA Mark II reactor at the Jozef Stefan Institute (JSI). To boost the epithermal neutron flux at the reference irradiation

  11. Conceptual design of a clinical BNCT beam in an adjacent dry cell of the Jozef Stefan Institute TRIGA reactor

    NARCIS (Netherlands)

    Maucec, M

    2000-01-01

    The MCNP4B Monte Carlo transport code is used in a feasibility study of the epithermal neutron boron neutron capture therapy facility in the thermalizing column of the 250-kW TRIGA Mark II reactor at the Jozef Stefan Institute (JSI). To boost the epithermal neutron flux at the reference irradiation

  12. Designing a TRIGA for environmental compatibility

    International Nuclear Information System (INIS)

    Profio, A.E.

    1972-01-01

    A 10 kW TRIGA Mark I teaching reactor is programmed for the new Engineering Unit 2 building on the main campus of UCSB. A special effort has been made to keep radioactivity in the reactor room air and exhaust air to a minimum. The regular pneumatic transfer system is being replaced by an inert-gas pressure system, or a closed-cycle air system, to avoid argon activation and release. Other experimental facilities will be filled with water or carbon dioxide, or sealed, to prevent release of argon-41. The remaining source of Ar-41, from the air dissolved in the pool water, cannot be completely eliminated. The campus has a policy of not discharging liquid radioactive wastes to the sewer. Experience at other installations indicates that the ion exchanger in the purification loop is effective in removing activated corrosion products or impurities, and aside from the short-lived N-16 and some Ar-41, radioactivity of the pool water should be quite low. Solid wastes, which would include the spent ion exchange resin, are collected by an independent firm for burial in a special nuclear disposal site in Nevada. Other important considerations in siting the UCSB reactor are the proximity to Santa Barbara Municipal Airport, and the seismic activity. We plan to project the fuel elements against damage by falling aircraft or parts by addition of a thick steel cover over the pool. Earthquakes have been taken into account in the design of the building, and especially the below-ground, reinforced-concrete, aluminum-lined pool

  13. Establishing the National Expression in the Work of the Independent Group of Slovenian Artists (The Independents

    Directory of Open Access Journals (Sweden)

    Asta Vrečko

    2015-12-01

    Full Text Available The interwar period was ripe with political crises connected to the national question in the Kingdom of SHS and the Kingdom of Yugoslavia. The relationship between Yugoslav and Slovene identity again became central for the question of national emancipation within an increasing supranational conflict and became the focus of visual arts in the 1930s. After a decade marked by Expressionism and New Objectivity in the thirties, values of moderate modernism and the quest for national expression re-emerged. At the time a new group of artists emerged on the Slovene artistic scene. They were schooled in Zagreb, the cultural centre of the Kingdom of Yugoslavia, where intense polemics regarding national expression in art were taking place. This contribution outlines the search for “our expression” in art as understood by the central protagonists of the art scene in Croatia, Krsto Hegedušić and Ljubo Babić. The latter especially was of central importance to the formation of the young Slovene art, because he was a prolific writer and one of the most important professors at the Academy of Fine Arts in Zagreb. The former Slovenian students, who formed the Independent group of Slovenian artists (Klub neodvisnih slovenskih likovnih umetnikov emerged in the turbulent years before the outbreak of World War II. In art, so they claimed, they were seeking their own, Slovenian national visual expression. In this search they took inspiration from Croatian artists, whose ideas they adapted to the Slovenian situation. At the same time, they legitimised their efforts with references to Slovene impressionists, who were regarded as the founding fathers of Slovene national art. In this way the Independents (Neodvisni sought to highlight the continuity in their search for Slovene national expression in art despite the transformed historical context. They based their national expression in art on a modernist version of Slovene impressionism. They combined this with

  14. Generation X in Slovenia(n

    Directory of Open Access Journals (Sweden)

    Romi Češčut

    2010-12-01

    Full Text Available Addressing themes of family, interpersonal relationships, historicity, jobs, religion, and apocalypse Generation X narrative includes works by young American writers in the 80s and 90s of the twentieth century. The search for oneʹs identity in urban landscape is heavily influenced by mass media, pop culture and consumerism. Slovenian press and professional literature provided only scarce response to Generation X fiction which is also influenced by the ambiguity of the term Generation X and the essence of its culture and literature, which is also true for American literary criticism. The paper aims to explore the reception of novels by Douglas Coupland, Bret Easton Ellis, and Jay McInerney and their analyses with emphasis on narrative, themes of consumerism and mass media, characters, and style of writing.

  15. State of Vision Development in Slovenian Companies

    Directory of Open Access Journals (Sweden)

    Vojko Toman

    2014-05-01

    Full Text Available Vision is a prerequisite for efficient strategic planning and the effectiveness of a company. If a company has no vision (i.e., it does not know where it is heading, then it cannot build on advantages, eliminate weaknesses, exploit opportunities and avoid threats. The term ‘vision’ is often used in scientific and professional literature, but it should be noted that different authors understand the term differently and often discuss it inadequately. Many questions regarding the nature of vision arise in practice and in theory, and I answer many of them in my article. I define vision, explain the reasons for its necessity and provide its characteristics and content. I define mission and explain the main difference between vision and mission. The majority of the article presents the results of empirical research on the state of vision setting in Slovenian companies. The article highlights the way in which these terms are understood by top managers.

  16. Dictionary of the Slovenian Sign Language on the WWW

    OpenAIRE

    Cempre, Luka; Bešir, Aleksander; Solina, Franc

    2013-01-01

    The article describes technical and user-interface issues of transferring the contents and functionality of the CD-ROM version of the Slovenian sing language dictionary to the web. The dictionary of Slovenian sign language consist of video clips showing the demonstra- tion of signs that deaf people use for communication, text description of the words corresponding to the signs and pictures illustrating the same word/sign. A new technical solution—a video sprite—for concatenating subsections o...

  17. Job satisfaction of Slovenian hospital nursing workforce.

    Science.gov (United States)

    Prosen, Mirko; Piskar, Franka

    2015-03-01

    To test the psychometric properties of the McCloskey-Mueller Satisfaction Scale and to assess which of the McCloskey-Mueller Satisfaction Scale dimensionalities have a considerable impact on job satisfaction of nursing employees in three public Slovenian hospitals. Job satisfaction of nurses is linked to productivity, turnover, absenteeism and patient outcomes. Little is known about the factors contributing to job satisfaction among Slovenian hospital nurses. Understanding the contributing factors could help nurse managers to take appropriate measures. A cross-sectional survey study was used to obtain a sample of 169 registered nursing assistants and 74 registered nurses working in three public hospitals in Slovenia, from which data was obtained using the McCloskey-Mueller Satisfaction Scale. Dimensionality was tested using exploratory factor analysis. A seven-factor structure of 29 items was obtained, which accounted for 54.3% of the total variance in job satisfaction, and was internally consistent (Cronbach's alpha coefficient of the instrument was 0.78). The first factor 'Satisfaction with Interaction Opportunities', which is a component of the social rewards dimension in the McCloskey-Mueller Satisfaction Scale, explained 30.6% of the variation. The registered nursing assistants' job dissatisfaction was higher than that of the registered nurses. Both were mostly dissatisfied with professional opportunities. Using the factor analysis, a seven-factor structure was found instead of the originally introduced eight-factor model, which suggests a need for further redevelopment of the McCloskey-Mueller Satisfaction Scale. The results suggest that operational management needs to revitalize the work environment by ensuring proactive leadership and allowing participation in the decision-making process, while health-care organisations need to support the professional development of registered nursing assistants and registered nurses in order to achieve sustainable effects

  18. Dynamics of TRIGA-3 Salazar Reactor

    International Nuclear Information System (INIS)

    Gallardo S, L.F.

    1990-01-01

    The theoretical study of temporal behavior of a nuclear reactor is of great importance, since it allows to know, in advance, the conditions to which a reactor is going to be submitted. The reliability of two computer codes (AIREK-JEN and PLANKIN) designed to reproduce the temporal behavior of nuclear reactors, generally power reactors, when they are applied to reproduce the dynamic behavior of TRIGA-3 Salazar Reactor is analyzed. In the first chapters, the fundamental equations that solve this computer codes are deduced, and also the main characteristics of TRIGA-3 Salazar Reactor and the necessary data to run the programs are presented; later the results obtained with the computer codes and the experimental results reported in the operational logbook of the reactor are compared, with the result that such computer codes are applicable to the temporal study of TRIGA-3 Salazar Reactor. (Author)

  19. Possibilities of miniaturizing the TRIGA-reactor

    International Nuclear Information System (INIS)

    Bobleter, O.; Brunner, P.; Schachner, H.

    1976-01-01

    It is proposed to decrease the depth of the TRIGA pool in cases where the construction of the normal-sized pool causes difficulty. The loss of shielding in the vertical direction will be compensated by lead and lead glass. The influence of these changes in design on the reactor components (control rods, instrumentation, neutron beam tubes, pneumatic system, etc.) is discussed. The experimental part of the work concerns the irradiation of lead glasses with varying contents of lead and cerium, which was carried out in the pool at different distances from the TRIGA core. The advantages of a possible reduction in size of the TRIGA reactor by using lead and lead glass as shielding are compared with the main disadvantages of these materials (darkening of the glass and high prices). (author)

  20. Reading Slovenian Novels in Selected Branches of Ljubljana City Library

    Directory of Open Access Journals (Sweden)

    Katja Šikonja

    2015-09-01

    Full Text Available Purpose: The article presents a research paper trying to identify the reasons for the assumption, widely accepted by Slovenian library profession that Slovenians do not read novels written by domestic authors.Methodology/approach: The research was conducted in 2014 in the Ljubljana City Library. A small sample of fifty adult users in five branches of Ljubljana City Library was selected. Data were gathered by semi-structured interview (questions were prepared in advance but could be tailored to the needs of the interview. Annual list of the most popular book titles was used.Results: Answers were classified in the following groups: (1 Problems of Slovenian novel (2 Insufficiently known (3 Foreign is better (4 Mandatory school reading lists (5 Other.Originality/practical implications: The research is the first attempt to thoroughly deal with the question of reading modern Slovenian novels in the region of Central Slovenia. Due to insufficient sample size, the results could not be generalized and applied to the entire Slovenian population. However, they could represent a starting point for the planning of future library activities enhancing the reading of Slovenian literature in the region of Central Slovenia.

  1. History, Development and Future of TRIGA Research Reactors

    International Nuclear Information System (INIS)

    2016-01-01

    Due to its particular fuel design and resulting enhanced inherent safety features, TRIGA reactors (Training, Research, Isotopes, General Atomics) constitute a ‘class of their own’ among the large variety of research reactors built world-wide. This publication summarizes in a single document the information on the past and present of TRIGA research reactors and presents an outlook in view of potential issues to be solved by TRIGA operating organizations in the near future. It covers the historical development and basic TRIGA characteristics, followed by utilization, fuel conversion and ageing management of TRIGA research reactors. It continues with issues and challenges, introduction to the global TRIGA research reactor network and concludes with future perspectives. The publication is complemented with a CD-ROM to illustrate the historical developments of TRIGA research reactors through individual facility examples and experiences

  2. The research reactor TRIGA Heidelberg II

    International Nuclear Information System (INIS)

    Maier-Borst, W.; Krauss, O.

    1988-01-01

    The reactor is in operation since the beginning of 1978. On the base of the working experience gathered during that time employing the TRIGA in biomedical research, especially the irradiation units have been extended or newly developed. Several TRIGA users have reported difficulties in using the rotary irradiation system. It became obvious that the alternatives to the original Lazy Susan are not commonly known. In this report, the open rotary system fed by a hydraulic rabbit system, which has proved successful in this form during the past ten years is presented

  3. FIR 1 TRIGA activity inventories for decommissioning planning

    International Nuclear Information System (INIS)

    Raety, Antti; Kotiluoto, Petri

    2016-01-01

    The objective of the study has been to estimate the residual activity in the decommissioning waste of TRIGA Mark II type research reactor FiR 1 in Finland. Neutron flux distributions were calculated with Monte Carlo code MCNP. These were used in ORIGEN-S point-depletion code to calculate the neutron induced activity of materials at different time points by modelling the irradiation history and radioactive decay. The knowledge of radioactive inventory of irradiated materials is important in the planning of the decommissioning activities and is essential for predicting the radiological impact to personnel and environment. Decommissioning waste consists mainly of ordinary concrete, aluminium, steel and graphite parts. Results include uncertainties due to assumptions on material compositions and possible diffusion of gaseous nuclides. Comparison to activity inventory estimates of two other decommissioned research reactors is also presented. (authors)

  4. Some applied isotope techniques at the Finnish TRIGA Laboratory

    International Nuclear Information System (INIS)

    Tamminen, A.

    1972-01-01

    The paper describes two separate radioactive tracer methods and a delayed neutron analyzer system. A process study in a ferrochrome smelter was based on the activation of large amounts of process input materials in special sample holders on the reflector of Triga Mark II reactor. In a typical surface water study 82 Br-solution has been injected in a waste water canal at a pulp and paper factory. The dilution mixing and flow of the tracer can be followed in the adjoining lake system for 6-8 days and up to a distance of 10 km. The tracer concentration has been measured directly without any sampling procedures. A delayed neutron analyzer for routine uranium ore analyses is presented. A polyethylene moderator block and seven parallelly connected BF 3 -detectors have been used in conjunction with a fast pneumatic sample transfer and irradiation system. (author)

  5. Radiation Protection in Slovenia Over the Past Fifty Years (1963-2013) and the Slovenian Society of Radiation Protection

    International Nuclear Information System (INIS)

    Omahen, G.; Krizman, M.J.

    2013-01-01

    The use of the ionizing radiation sources in Slovenia started as early as 1900 when X-ray device was put in operation; the first radioactive source was used two years later. Artificial radioactive sources were introduced from 1954 onwards. The use of radioactive sources in industry started in the middle of the 1950's when industrial radiography was introduced due to strong metal industry in Slovenia. Four nuclear facilities were built in Slovenia: the research reactor TRIGA (1966), the Krško nuclear power plant (1983), the mining and milling uranium complex at Žirovski Vrh (1984) and the low and intermediate level radioactive waste storage (1986). The infrastructure of radiation protection (RP) in the former Yugoslavia was established as late as the first Law on RP was adopted in 1959, the competent authorities were defined and technical support organisations for RP were designated. But the whole infrastructure could not follow the rapid development of nuclear industry and the extent uses of sources. After joining EU, the changes in legislation made a significant shift ahead in radiation protection, as regards the quality of the implementation of radiation protection measures as the intensity of administrative and inspection controls. Slovenian Radiation Protection Society was established in 1981 during the 11th symposium of the Yugoslav Radiation Protection Society. The role of the Slovenian Society for Radiation Protection has never been significant, mostly due to a small critical mass of membership. This is sometimes advantageous since everyone knows each other and can easily come with the problem to be solved. This feature reduces the need for the Society to be active as a formal association. The main role of the Society is the distribution of actual information on RP and related important events.(author)

  6. Planning and implementation of Istanbul Technical University TRIGA research reactor program

    International Nuclear Information System (INIS)

    Aybers, N.; Yavuz, H.; Bayulken, A.

    1982-01-01

    The Istanbul Technical University TRIGA Research Reactor at the Institute for Nuclear Energy, which went critical on March 11, 1979 is basically a pulsing type TRIGA Mark - II reactor. Completion of the ITU-TRR contributed to broaden the role of the Institute for Nuclear Energy of the Technical University in Istanbul in the nuclear field by providing for the first time adequate on-campus experimental facilities for nuclear engineering studies to ITU students. The research program which is currently under planning at ITU-NEE encompasses: a) Neutron activation analysis studies by techniques and applications to chemistry, mining, materials research, archaeological and biomedical studies; b) applications of Radioisotopes; c) Radiography with reactor neutron beams; d) Radiation Pulsing

  7. The research reactor TRIGA Mainz. A neutron source for versatile applications in research and education

    International Nuclear Information System (INIS)

    Eberhardt, K.; Kronenberg, A.

    2000-01-01

    Currently, four research reactors with a thermal power ranging from 0.1 to 23 MW th are in operation in Germany and one new reactor (20 MW th ) is under construction. The TRIGA Mark II reactor at the Institut fuer Kernchemie became first critical on August 3, 1965. It can be operated in the steady state mode with a maximum power of 100 kW th and in the pulse mode with a peak power of 250 MW th . A survey of the research programmes carried out at the TRIGA Mainz is given covering a wide range of applications in basic and applied science in nuclear chemistry, nuclear- and particle physics. Furthermore, the reactor is used for neutron activation analysis and for education and training of students and technical personal. (orig.) [de

  8. Knowledge management initiatives benefits for the Slovenian public sector

    Directory of Open Access Journals (Sweden)

    Simon Colnar

    2017-01-01

    Full Text Available This paper highlights the importance of knowledge management in Slovenian public sector organizations. Knowledge management has received a lot of attention in the past two decades, however in the public sector it is still under-researched. The global financial and economic crisis revealed some important organizational weaknesses in the Republic of Slovenia, some particularly due to the ineffectiveness of the Slovenian public sector, which ranks amongst the worst in the Euro zone. Authors argue that a stronger commitment to knowledge management, which is currently unused in the Slovenian public sector, represents an opportunity to coordinate and exploit public sector organizational knowledge resources. After analysing existing literature, authors have identified examples of good practices from foreign countries that could be partially transferred and adapted into the Slovenian environment. Since the efficient use of knowledge is linked to the performance of public sector organizations, the paper suggests that successful implementation of knowledge management initiatives should result in a more efficient public sector and, indirectly, in improved international public sector competitiveness rankings. This paper is also considered to be important for public sector practitioners and managers, as it proposes implementation of a knowledge management pilot project in Slovenian public sector.

  9. PHYSICIAN FRIDERIK PREGL, NOBELIST OF SLOVENIAN DESCENT

    Directory of Open Access Journals (Sweden)

    Zvonka Zupanič Slavec

    2001-07-01

    Full Text Available With his Nobel Prize for chemistry in 1923, Friderik (Fritz Pregl (1869–1930, a physician and a university professor for medical chemistry became a famous person both among Slovenians and world’s most eminent scientists. He did not win the Nobel Prize only for his work on the field of microanalysis of organic substances because he would have invented something very new but because he made a significant contribution to the improvement of the methodology in the quantitative organic microanalysis of that time. In his scientific work he focused on reducing the amount of substance designed for the analysis and on the improvement of the analytical scales. He improved the scales’ accuracy to a thousandth of a gram, decreased the amount of testing substance and reduced working time and the energy spared for the work considerably. Consequently, the study of substance was possible also in cases where only 3–5mg of the substance or even less were available. The same amount of substance, which had been sufficient only for one analyse, was now enough to carry out more than 50 analyses. Therefore, his improvements made the work of physiological and pathological chemists more exact and quicker. Scientific success and many publications made Pregl’s name; he became an honorary doctor of the wellknown university in Göttingen, a member of the academy of sciences and arts in Vienna and an honorary citizen of Graz

  10. Calcite precipitates in Slovenian bottled waters.

    Science.gov (United States)

    Stanič, Tamara Ferjan; Miler, Miloš; Brenčič, Mihael; Gosar, Mateja

    2017-06-01

    Storage of bottled waters in varying ambient conditions affects its characteristics. Different storage conditions cause changes in the initial chemical composition of bottled water which lead to the occurrence of precipitates with various morphologies. In order to assess the relationship between water composition, storage conditions and precipitate morphology, a study of four brands of Slovenian bottled water stored in PET bottles was carried out. Chemical analyses of the main ions and measurements of the physical properties of water samples were performed before and after storage of water samples at different ambient conditions. SEM/EDS analysis of precipitates was performed after elapsed storage time. The results show that the presence of Mg 2+ , SO 4 2- , SiO 2 , Al, Mn and other impurities such as K + , Na + , Ba and Sr in the water controlled precipitate morphology by inhibiting crystal growth and leading to elongated rhombohedral calcite crystal forms which exhibit furrowed surfaces and calcite rosettes. Different storage conditions, however, affected the number of crystallization nuclei and size of calcite crystals. Hollow calcite spheres composed of cleavage rhombohedrons formed in the water with variable storage conditions by a combination of evaporation and precipitation of water droplets during high temperatures or by the bubble templating method.

  11. Ethics of managers in Slovenian public administration

    Directory of Open Access Journals (Sweden)

    Zlatko Nedelko

    2015-01-01

    Full Text Available The main purpose of this paper is to examine how managers’ personal values and managers’ attitudes towards the natural and social environment are shaping the ethics of those same managers in public administration. The findings are based on a sample of 212 managers from Slovenian public administration. Personal values were measured using the Schwartz value survey, while attitudes toward natural and social environment were measured with a validated questionnaire. Results show that managers’ self-enhancing values are positively related to their attitudes toward both natural and social environment and their ethics. Managers’ self-transcendence values were found to be negatively associated with their attitudes toward the social environment and their ethics. Managers’ attitudes toward natural and social environment are both positively related with the managers’ ethics. The mediation effect of the attitudes towards the social environment on the relationships between managers’ personal values and their ethics is positive and significant. The main cognition is that managers’ attitudes towards the social environment are a significantly stronger predictor of managers’ ethics than are managers’ personal values.

  12. Slovenian between the wild and good conduct

    Directory of Open Access Journals (Sweden)

    Vanda Rebolj

    2008-12-01

    Full Text Available New concepts and strategies of learning, resulting from the economic needs of the society, have brought about many new concepts and new content of those already in use. At the same time, the development of new technologies, most of all the information technology, broadened the existing and set off new opportunities in the economic, cognitive and social field. To fully understand the use of the existing, although already established terminology, it takes more. Adequate communication of knowledge is not possible any more. Even mutual communication between a teacher and a student is not without difficulty. While managing professional and work problems, without strategy and language policies we resort to provisional solutions, diminishing the culture of the language and its users, as well as the possibility of the nation’s equal rights in the global world. For nine years, Islovar, the online terminological dictionary of informatics, has been edited by the Slovenian Society of Informatics. Judging by the frequency of search, it has been successfully answering the issues concerning Slovene terms in informatics. The author's intention is to investigate the present state of the Slovene terminology in general and by some concrete examples, exposing some problems and solutions which might help other terminology fields.

  13. The vicious cycle of Slovenian book use and the potential role of public libraries in solving it

    Directory of Open Access Journals (Sweden)

    Teja Zorko

    2007-01-01

    Full Text Available The use of books in Slovenia is marked with an insufficient bookstore network and with a well developed network of public libraries with a large number of loans that supplements a market of cheap paperback books, which is known in large language communities abroad. The resolution on National Program for Culture among the set goals for the improvement of use of books in Slovenia states also encouragement to develop bookstore network, equally divided across the entire Slovenian cultural area, with which the formation of bookstore corners in the framework of already existing public cultural institutions is proposed. From 2003, Ministry of Culture is supporting the good bookstores, but the endeavors haven’t reached the set goals yet. This contribution brings theoretical presumptions of principal thinking on the possibility of directing the libraries in the direction of marketing the books and the findings of a survey conducted among the directors of Slovenian general libraries. The findings show the predominant directors’ opinion on principal usefulness of potential sale of books in libraries, especially for the users. Almost a half of the managers of all Slovenian public libraries in principle support the introduction of book sale in their library if proper conditions would have been set. However, they do not expect any financial benefit from this service.

  14. 10. European TRIGA users conference. Papers and abstracts

    International Nuclear Information System (INIS)

    1988-01-01

    The Tenth European TRIGA Users Conference was held in Vienna, September 14-16, 1988 under the sponsorship of the Atominstitut. The main areas of discussions were: Reactor operation and maintenance experiences; New developments and improvements of TRIGA components and systems, including instrumentation; Fuel and fuel management; Safety aspects, licensing and radiation protection; Experiments with TRIGA reactors; Radiochemistry, radioisotope production and NAA; and Reactor physics

  15. [2. European] TRIGA owners' conference. Papers and abstracts

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1972-07-01

    The Second European TRIGA Owners' Conference was held in Pavia, Italy, September 1972. The meeting was organized by the University of Pavia Applied Nuclear Energy Laboratory (L.E.N.A.). Sixty-two attendees representing 12 TRIGA reactor centers in Europe, South America, and the United States were present at the Conference. The main areas of discussions were: Reactor operation and maintenance experience; Research programs and TRIGA technology development.

  16. 10. European TRIGA users conference. Papers and abstracts

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-07-01

    The Tenth European TRIGA Users Conference was held in Vienna, September 14-16, 1988 under the sponsorship of the Atominstitut. The main areas of discussions were: Reactor operation and maintenance experiences; New developments and improvements of TRIGA components and systems, including instrumentation; Fuel and fuel management; Safety aspects, licensing and radiation protection; Experiments with TRIGA reactors; Radiochemistry, radioisotope production and NAA; and Reactor physics.

  17. [2. European] TRIGA owners' conference. Papers and abstracts

    International Nuclear Information System (INIS)

    1972-01-01

    The Second European TRIGA Owners' Conference was held in Pavia, Italy, September 1972. The meeting was organized by the University of Pavia Applied Nuclear Energy Laboratory (L.E.N.A.). Sixty-two attendees representing 12 TRIGA reactor centers in Europe, South America, and the United States were present at the Conference. The main areas of discussions were: Reactor operation and maintenance experience; Research programs and TRIGA technology development

  18. The Dynamic Internationalization Model of Slovenian Born Global SMEs

    Directory of Open Access Journals (Sweden)

    Ina Lejko

    2013-01-01

    Full Text Available Small and medium sized enterprises (SMEs are important businessactors in the Slovenian, as well as European economy. Inaddition to the current global market conditions, reflecting a severeeconomic downturn, the SMEs in Slovenia and other transitioneconomies operate under additional extensive external pressures,arising from the opening of their domestic markets. Undersuch conditions, companies, including SMEs, perceive internationalizationas an inevitable, or even urgent step in the processof their business operations. However, companies pursue differentpaths in their internationalization efforts, one of them beinga rapid internationalization strategy, denoted as the Born Globalconcept. In the paper, we explore the internationalization processof Slovenian Born Global SMEs. We employ an exploratory qualitativecase study analysis of selected Slovenian SMEs in order tograsp the key characteristics of their internationalization process.On the basis of the latter we construct a dynamic internationalizationmodel that might be used as a conceptual framework forempirical research of dynamic SMEs market behavior in Sloveniaand other transition countries.

  19. Relationship Between Management and Leadership and Characteristics of Slovenian Managers

    Directory of Open Access Journals (Sweden)

    Milena Kramar Zupan

    2012-11-01

    Full Text Available For years, leadership was understood as a managerial function. A significant number of authors currently see leadership as replacing management, or as a different but overlapping function. In the first part of this article, the author supports her opinion of leadership as being one of the managerial functions, emphasizing that both leadership and management have developed over time. More emphasis is given to research (and its results among Slovenian managers showing that they are aware of the increasing importance of leadership compared to other managerial functions. The increased importance of leadership means that managers have to devote more time and attention to employees. Slovenian managers are still overly concerned with their reputation and promotion, and less with the satisfaction and achievements of their employees. Their loyalty to employees is weak, and they are more individualists than team workers. The characteristics of Slovenian managers (supported by research that led to the aforementioned conclusions are discussed in this article.

  20. Reactor instrumentation renewal of the TRIGA reactor Vienna, Austria

    International Nuclear Information System (INIS)

    Boeck, H.; Weiss, H.; Hood, W.E.; Hyde, W.K.

    1992-01-01

    The TRIGA Mark-II reactor at the Atominstitut in Vienna, Austria is replacing its twenty-four year old instrumentation system with a microprocessor based control system supplied by General Atomics. Ageing components, new governmental safety requirements and a need for state of the art instrumentation for training students has spurred the demand for new reactor instrumentation. In Austria a government appointed expert is assigned the responsibility of reviewing the proposed installation and verifying all safety aspects. After a positive review, final assembly and checkout of the instrumentation system may commence. The instrumentation system consists of three basic modules: the control system console, the data acquisition console and the NH-1000 wide range channel. Digital communications greatly reduce interwiring requirements. Hardwired safety channels are independent of computer control, thus, the instrumentation system in no way relies on any computer intervention for safety function. In addition, both the CSC and DAC computers are continuously monitored for proper operation via watchdog circuits which are capable of shutting down the reactor in the event of computer malfunction. Safety channels include two interlocked NMP-1000 multi-range linear channels for steady state mode, an NPP-1000 linear safety channel for pulse mode and a set of three independent fuel temperature monitoring channels. The microprocessor controlled wide range NM- 1000 digital neutron monitor (fission chamber based) functions as a startup/operational channel, and provides all power level related Interlocks. The Atominstitut TRIGA reactor is configured for four modes of operation: manual mode, automatic mode (servo control), pulsing mode and square wave mode. Control of the standard control rods is via stepping motor control rod drives, which offers the operator the choice of which control rods are operated by the servo system in automatic and square wave model. (author)

  1. 9. European TRIGA users' conference. Papers and abstracts

    International Nuclear Information System (INIS)

    1986-01-01

    Operation and maintenance experience, new developments and improvements of TRIGA reactors, fuel management, radiation protection, licensing, uses for research and isotope production are discussed at the Conference

  2. Development and perspectives of Slovenian medical terminology and lexicography - the historical role of Zdravniški vestnik

    Directory of Open Access Journals (Sweden)

    Dušan Sket

    2011-02-01

    Conclusions: Slovenian medicine has made important steps in the development of modern Slovenian medical language. The current state of the art enables Slovenian physicians and biomedical professionals to follow the progress of global medicine and to create adequate Slovenian expressions in all medical disciplines.

  3. Military Jargon in the Slovenian Translation of Hostile Waters

    Directory of Open Access Journals (Sweden)

    Simon Zupan

    2014-05-01

    Full Text Available The article examines Slovenian translations of military jargon in the non-fiction novel Hostile Waters. In the introductory part, jargon is presented as a linguistic category as well as its main features in the novel. Next, select examples from the original text are compared to their Slovenian equivalents. The focus is on collocations and lexically dense nominal phrases. The comparison finds that most translation shifts in the target text occur because of incorrect interpretation of technical jargon expressions in the original. As a result, the target text reader perceives certain situations differently than the source text reader.

  4. Various Stagings of Cankar’s Works at the Slovenian National Theater in Ljubljana and Other Slovenian Theaters in the Interwar Period (1918–1941

    Directory of Open Access Journals (Sweden)

    Ana Kocjančič

    2007-12-01

    Full Text Available Plays by Ivan Cankar unequivocally marked Slovenian theater in the period from 1918 to 1941. In addition to Shakespeare’s works, it was Cankar’s plays that were most frequently performed on the Slovenian stage. His works especially appealed to directors that were seeking deeper, symbolic meanings of the text, which they tried to present to the audience to the best of their ability. Thus, Cankar’s narrative was intensified through directing and acting, whereas the scenery was of secondary importance in most performances. These mostly included painted scenes or backdrops to represent the setting. Only the stagings of Pohujšanje v dolini Šentflorjanski (The Scandal in the St. Florian Valley, Kralj na Betajnovi (The King of Betajnova, Hlapec Jernej in njegova pravica (The Servant Jernej and His Justice, and Lepa Vida (The Beautiful Vida contained more developed scenography. However, until the 1930s, scenery design for Cankar’s plays performed on the professional stage varied between painted backdrops and expressionist sets. It was not until the appearance of the director and scenographer Bojan Stupica that the scenery of these plays reached the boundaries of new realism and modern avant-garde. Until then, an unspoken rule had been in force that the scenery of Cankar’s plays should not extend beyond the boundaries of expressionism. This rule was observed even by the avant-garde painter Avgust Černigoj. However, Cankar’s plays were staged completely differently in workers’ theaters and popular theaters. With new avant-garde staging, they often surpassed the development of theater design in professional theaters, and caught up with contemporary formal ideas in Slovenian and European fine arts. Here, Cankar’s works were staged as anti-political propaganda. In order to better express their new ideas, these theaters also used new tools, such as projectors and film clips, and experimented with spotlights. The most original among these

  5. Modeling a TRIGA Power System with ATHENA

    International Nuclear Information System (INIS)

    Davis, C.B.

    1985-01-01

    GA Technologies TRIGA Power System (TPS) is a power-producing version of the Training Research and Isotope General Atomic (TRIGA) reactor. The TPS analyzed here is designed to produce 10 MW of electrical power. The TPS features three major thermal-hydraulic systems, including a water-filled primary coolant system, a water-filled residual heat removal system, and a Freon-filled secondary coolant system. A thermal-hydraulic model of the TPS was developed using the Advanced Thermal Hydraulic Energy Network Analyzer (ATHENA) computer code, and two demonstration calculations were performed. ATHENA is based on the Reactor Excursion and Leak Analysis Program (RELAP5/MOD2) and has similar, but expanded capabilities. The expanded capabilities allow the representation of several different fluids, including water and Freon-11. This paper provides descriptions of the TPS, the ATHENA computer code and ATHENA TPS model, results of the demonstration calculations, conclusions, and references. 2 refs., 7 figs

  6. Performance Monitoring for Nuclear Safety Related Instrumentation at PUSPATI TRIGA Reactor (RTP)

    International Nuclear Information System (INIS)

    Zareen Khan Abdul Jalil Khan; Ridzuan Abdul Mutalib; Mohd Sabri Minhat

    2015-01-01

    The Reactor TRIGA PUSPATI (RTP) at Malaysia Nuclear Agency is a TRIGA Mark II type reactor and pool type cooled by natural circulation of light water. This paper describe on performance monitoring for nuclear safety related instrumentation in TRIGA PUSPATI Reactor (RTP) of based on various parameter of reactor safety instrument channel such as log power, linear power, Fuel temperature, coolant temperature will take into consideration. Methodology of performance on estimation and monitoring is to evaluate and analysis of reactor parameters which is important of reactor safety and control. And also to estimate power measurement, differential of log and linear power and fuel temperature during reactor start-up, operation and shutdown .This study also focus on neutron power fluctuation from fission chamber during reactor start-up and operation. This work will present result of performance monitoring from RTP which indicated the safety parameter identification and initiate safety action on crossing the threshold set point trip. Conclude that performance of nuclear safety related instrumentation will improved the reactor control and safety parameter during reactor start-up, operation and shutdown. (author)

  7. Validation of neutron flux redistribution factors in JSI TRIGA reactor due to control rod movements

    International Nuclear Information System (INIS)

    Kaiba, Tanja; Žerovnik, Gašper; Jazbec, Anže; Štancar, Žiga; Barbot, Loïc; Fourmentel, Damien; Snoj, Luka

    2015-01-01

    For efficient utilization of research reactors, such as TRIGA Mark II reactor in Ljubljana, it is important to know neutron flux distribution in the reactor as accurately as possible. The focus of this study is on the neutron flux redistributions due to control rod movements. For analyzing neutron flux redistributions, Monte Carlo calculations of fission rate distributions with the JSI TRIGA reactor model at different control rod configurations have been performed. Sensitivity of the detector response due to control rod movement have been studied. Optimal radial and axial positions of the detector have been determined. Measurements of the axial neutron flux distribution using the CEA manufactured fission chambers have been performed. The experiments at different control rod positions were conducted and compared with the MCNP calculations for a fixed detector axial position. In the future, simultaneous on-line measurements with multiple fission chambers will be performed inside the reactor core for a more accurate on-line power monitoring system. - Highlights: • Neutron flux redistribution due to control rod movement in JSI TRIGA has been studied. • Detector response sensitivity to the control rod position has been minimized. • Optimal radial and axial detector positions have been determined

  8. Fission products detection in irradiated TRIGA fuel by means of gamma spectroscopy and MCNP calculation.

    Science.gov (United States)

    Cagnazzo, M; Borio di Tigliole, A; Böck, H; Villa, M

    2018-05-01

    Aim of this work was the detection of fission products activity distribution along the axial dimension of irradiated fuel elements (FEs) at the TRIGA Mark II research reactor of the Technische Universität (TU) Wien. The activity distribution was measured by means of a customized fuel gamma scanning device, which includes a vertical lifting system to move the fuel rod along its vertical axis. For each investigated FE, a gamma spectrum measurement was performed along the vertical axis, with steps of 1 cm, in order to determine the axial distribution of the fission products. After the fuel elements underwent a relatively short cooling down period, different fission products were detected. The activity concentration was determined by calibrating the gamma detector with a standard calibration source of known activity and by MCNP6 simulations for the evaluation of self-absorption and geometric effects. Given the specific TRIGA fuel composition, a correction procedure is developed and used in this work for the measurement of the fission product Zr 95 . This measurement campaign is part of a more extended project aiming at the modelling of the TU Wien TRIGA reactor by means of different calculation codes (MCNP6, Serpent): the experimental results presented in this paper will be subsequently used for the benchmark of the models developed with the calculation codes. Copyright © 2018 Elsevier Ltd. All rights reserved.

  9. TRIGA International - History of Training Research Isotope production General Atomics

    International Nuclear Information System (INIS)

    2008-01-01

    TRIGA conceived at GA in 1956 by a distinguished group of scientists including Edward Teller and Freeman Dyson. First TRIGA reactor Mk-1 was commissioned on 3 may 1958 at G.A. Characteristic feature of TRIGA reactors is inherent safety: Sitting can be confinement or conventional building. TRIGA reactors are the most prevalent in the world: 67 reactors in 24 countries. Steady state powers up to 14 MWt, pulsing up to 22,000 MWt. To enlarge the scope of its manufactured products, CERCA engaged in a Joint Venture with General Atomics, and in July 1995 a new Company was founded: TRIGA INTERNATIONAL SAS (50% GA, 50% CERCA; Head Office: Paris (France); Sales offices: GA San Diego (Ca, USA) and CERCA Lyon (France); Manufacturing plant: CERCA Romans. General Atomics ID: founded in 1955 at San Diego, California, by General Dynamics; status: Privately held corporation; owners: Neal and Linden Blue; business: High technology research, design, manufacturing, and production for industry and Government in the U.S. and overseas; locations: U.S., Germany, Japan, Australia, Thailand, Morocco; employees: 5,000. TRIGA's ID: CERCA is a subsidiary of AREVA, born in November 05, 1957. Activities: fuel manufacture for research reactor, equipment and components for high-energy physics, radioactive sources and reference sources; plants locations: Romans and Pierrelatte (France); total strength: 180. Since the last five years TRIGA has manufactured and delivered more than 800 fuel elements with a door to door service. TRIGA International has the experience to manufacture all types of TRIGA fuel: standard fuel elements, instrumented fuel elements, fuel followed control rods, geometry: 37.3 mm (1.47 in.), 35.8 mm (1.4 in), 13 mm (0.5 in), chemical Composition: U w% 8.5, 12, 20, 30 and 45 w/o, erbium and no erbium. TRIGA International is on INL's approved vendor list (ISO 9000/NQA) and is ready to meet any TRIGA fuel needs either in the US or worldwide

  10. TRIGA research reactors with higher power density

    International Nuclear Information System (INIS)

    Whittemore, W.L.

    1994-01-01

    The recent trend in new or upgraded research reactors is to higher power densities (hence higher neutron flux levels) but not necessarily to higher power levels. The TRIGA LEU fuel with burnable poison is available in small diameter fuel rods capable of high power per rod (≅48 kW/rod) with acceptable peak fuel temperatures. The performance of a 10-MW research reactor with a compact core of hexagonal TRIGA fuel clusters has been calculated in detail. With its light water coolant, beryllium and D 2 O reflector regions, this reactor can provide in-core experiments with thermal fluxes in excess of 3 x 10 14 n/cm 2 ·s and fast fluxes (>0.1 MeV) of 2 x 10 14 n/cm 2 ·s. The core centerline thermal neutron flux in the D 2 O reflector is about 2 x 10 14 n/cm 2 ·s and the average core power density is about 230 kW/liter. Using other TRIGA fuel developed for 25-MW test reactors but arranged in hexagonal arrays, power densities in excess of 300 kW/liter are readily available. A core with TRIGA fuel operating at 15-MW and generating such a power density is capable of producing thermal neutron fluxes in a D 2 O reflector of 3 x 10 14 n/cm 2 ·s. A beryllium-filled central region of the core can further enhance the core leakage and hence the neutron flux in the reflector. (author)

  11. NFR TRIGA package design review report

    International Nuclear Information System (INIS)

    Clements, M.D.

    1994-01-01

    The purpose of this document is to compile, present and document the formal design review of the NRF TRIGA packaging. The contents of this document include: the briefing meeting presentations, package description, design calculations, package review drawings, meeting minutes, action item lists, review comment records, final resolutions, and released drawings. This design review required more than two meeting to resolve comments. Therefore, there are three meeting minutes and two action item lists

  12. Technical report on natural evaporation system for radioactive liquid waste treatment arising from TRIGA research reactors' decontamination and decommissioning activities

    International Nuclear Information System (INIS)

    Moon, J. S.; Jung, K. J.; Baek, S. T.; Jung, U. S.; Park, S. K.; Jung, K. H.

    1999-01-01

    This technical report described that radioactive liquid waste treatment for dismantling/decontamination of TRIGA Mark research reactor in Seoul. That is, we try safety treatment of operation radioactive liquid waste during of operating TRIGA Mark research reactor and dismantling radioactive liquid waste during R and D of research reactor hereafter, and by utilizing of new natural evaporation facility with describing design criteria of new natural evaporation facility. Therefore, this technical report described the quantity of present radioactive liquid waste and dismantling radioactive liquid waste hereafter, analysis the status of radial-rays/radioactivity, and also treatment method of this radioactive liquid waste. Also, we derived the method that the safeguard of outskirts environment and the cost down of radioactive liquid waste treatment by minimize of the radioactive liquid waste quantities, through-out design/operation of new natural evaporation facility for treatment of operation radioactive liquid waste and dismantling radioactive liquid waste. (author). 6 refs., 12 tabs., 5 figs

  13. 14. U.S. TRIGA users conference. Final program and summary of papers

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-07-01

    The following papers were presented at the Conference: Early Development and Use of the TRIGA Reactor; Results of the MCNP Analysis of 20/20 LEU Fuel for the Oregon State University TRIGA Reactor; Upgradeable 2MW TRIGA Reactor Design for the Morocco Nuclear Energy Center McClellan Nuclear Radiation Center TRIGA Reactor: Four Years of Operations.

  14. 14. U.S. TRIGA users conference. Final program and summary of papers

    International Nuclear Information System (INIS)

    1994-01-01

    The following papers were presented at the Conference: Early Development and Use of the TRIGA Reactor; Results of the MCNP Analysis of 20/20 LEU Fuel for the Oregon State University TRIGA Reactor; Upgradeable 2MW TRIGA Reactor Design for the Morocco Nuclear Energy Center McClellan Nuclear Radiation Center TRIGA Reactor: Four Years of Operations

  15. Characteristics of Suicide Attempters in a Slovenian High School Population.

    Science.gov (United States)

    Tomori, Martina; Zalar, Bojan

    2000-01-01

    In a study of Slovenian high school students (N=3,687) results show that those who had attempted suicide and those who had not differed in levels of self-esteem, emotional reaction to family problems, running away from home, and substance abuse. Differences in depression, suicide ideation, family suicide ideation, family suicide occurrence,…

  16. Adapting the Freiburg monosyllabic word test for Slovenian

    Directory of Open Access Journals (Sweden)

    Tatjana Marvin

    2017-12-01

    Full Text Available Speech audiometry is one of the standard methods used to diagnose the type of hearing loss and to assess the communication function of the patient by determining the level of the patient’s ability to understand and repeat words presented to him or her in a hearing test. For this purpose, the Slovenian adaptation of the German tests developed by Hahlbrock (1953, 1960 – the Freiburg Monosyllabic Word Test and the Freiburg Number Test – are used in Slovenia (adapted in 1968 by Pompe. In this paper we focus on the Freiburg Monosyllabic Word Test for Slovenian, which has been criticized by patients as well as in the literature for the unequal difficulty and frequency of the words, with many of these being extremely rare or even obsolete. As part of the patient’s communication function is retrieving the meaning of individual words by guessing, the less frequent and consequently less familiar words do not contribute to reliable testing results. We therefore adapt the test by identifying and removing such words and supplement them with phonetically similar words to preserve the phonetic balance of the list. The words used for replacement are extracted from the written corpus of Slovenian Gigafida and the spoken corpus of Slovenian GOS, while the optimal combinations of words are established by using computational algorithms.

  17. Analysis of Expatriation Process in a Slovenian Company

    Directory of Open Access Journals (Sweden)

    Pintar Rok

    2017-02-01

    Full Text Available Background and Purpose: The multinational companies require different approach of human resource management to achieve their goals. The reason is in employees who are working abroad, so-called expatriates. The purpose of the research is to investigate perceptions and experience of the expatriates working in one of the Slovenian multinational company.

  18. Topoclimatic map of the littoral zone in Slovenian Istria

    Directory of Open Access Journals (Sweden)

    Darko Ogrin

    2011-12-01

    Full Text Available The paper presents the basic topoclimatic features of the littoral zone in Slovenian Istria which result from general climate features and specific local conditions. The most widely spatially spread topoclimatic units arise from differences in insolation and the combination of local landforms and land use. They are presented on the map at a scale of 1 : 50,000.

  19. 6. European conference of TRIGA reactor users. Conference papers

    International Nuclear Information System (INIS)

    1980-01-01

    The Sixth European Conference of TRIGA Users was held in September 1980, in Mainz, Germany under the joint sponsorship of INTERATOM and the Institut fur Kernchemie. The main areas of discussions were: Fuel cycle aspects; New reactor developments and improvements; TRIGA applications; Operating and maintenance experiences and Instrumentation

  20. 7. European conference of TRIGA reactor users. Conference papers

    International Nuclear Information System (INIS)

    1982-01-01

    At the Seventh European Conference of TRIGA Users, held in September 1982, in Istanbul, Turkey, the following aspects are discussed: safety aspects of TRIGA reactors; developments and improvements; operating and maintenance experiences; applications; reactor calculations; fuel cycle aspects and research programs

  1. 7. European conference of TRIGA reactor users. Conference papers

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-07-01

    At the Seventh European Conference of TRIGA Users, held in September 1982, in Istanbul, Turkey, the following aspects are discussed: safety aspects of TRIGA reactors; developments and improvements; operating and maintenance experiences; applications; reactor calculations; fuel cycle aspects and research programs.

  2. 12. U.S. TRIGA users conference. Papers and abstracts

    International Nuclear Information System (INIS)

    1990-01-01

    The Conference presentations were devoted to the following topics: new developments and improvements, including modifications of TRIGA reactors and equipment; experiments with TRIGA reactors (Neutron Radiography); radiochemistry, radioisotope production and beam irradiations (experiment applications, simulation); reactor physics - fuel utilization; reactor operation and maintenance experience; safety aspects, licensing and radiation protection

  3. Proceedings of the 4. World TRIGA Users Conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-10-29

    This document gathers 30 presentations given at the 2008 Conference of the World TRIGA reactor Users. Most presentations are in the form of slides only, and few ones have an additional summary or are presented as an article only. All aspects of TRIGA-type reactors are approached, from upgrading to decommissioning, from radiotherapy to isotope production, from research program management to training, etc.

  4. Proceedings of the 4. World TRIGA Users Conference

    International Nuclear Information System (INIS)

    2008-01-01

    This document gathers 30 presentations given at the 2008 Conference of the World TRIGA reactor Users. Most presentations are in the form of slides only, and few ones have an additional summary or are presented as an article only. All aspects of TRIGA-type reactors are approached, from upgrading to decommissioning, from radiotherapy to isotope production, from research program management to training, etc

  5. Industrial and commercial applications for a Triga reactor

    International Nuclear Information System (INIS)

    Green, D.

    1986-01-01

    The Physics and Radioisotope Services Group of ICI operates a Triga Reactor in support of a commercial, Industrial Radioisotope Technology Service. The technical and commercial development of this business is discussed in the context of operating a Triga Reactor in an Industrial Environment. (author)

  6. Fission product release from TRIGA-LEU reactor fuels

    International Nuclear Information System (INIS)

    Baldwin, N.L.; Foushee, F.C.; Greenwood, J.S.

    1980-01-01

    Due to present international concerns over nuclear proliferation, TRIGA reactor fuels will utilize only low-enriched uranium (LEU) (enrichment <20%). This requires increased total uranium loading per unit volume of fuel in order to maintain the appropriate fissile loading. Tests were conducted to determine the fractional release of gaseous and metallic fission products from typical uranium-zirconium hydride TRIGA fuels containing up to 45 wt-% uranium. These tests, performed in late 1977 and early 1978, were similar to those conducted earlier on TRIGA fuels with 8.5 wt-% U. Fission gas release measurements were made on prototypic specimens from room temperature to 1100 deg. C in the TRIGA King Furnace Facility. The fuel specimens were irradiated in the TRIGA reactor at a low power level. The fractional releases of the gaseous nuclides of krypton and xenon were measured under steady-state operating conditions. Clean helium was used to sweep the fission gases released during irradiation from the furnace into a standard gas collection trap for gamma counting. The results of these tests on TRIGA-LEU fuel agree well with data from the similar, earlier tests on TRIGA fuel. The correlation used to calculate the release of fission products from 8.5 wt-% U TRIGA fuel applies equally well for U contents up to 45 wt-%. (author)

  7. Fuel burnup analysis for the Moroccan TRIGA research reactor

    International Nuclear Information System (INIS)

    El Bakkari, B.; El Bardouni, T.; Nacir, B.; El Younoussi, C.; Boulaich, Y.; Boukhal, H.; Zoubair, M.

    2013-01-01

    Highlights: ► A fuel burnup analysis of the 2 MW TRIGA MARK II Moroccan research reactor was established. ► Burnup calculations were done by means of the in-house developed burnup code BUCAL1. ► BUCAL1 uses the MCNP tallies directly in the calculation of the isotopic inventories. ► The reactor life time was found to be 3360 MW h considering full power operating conditions. ► Power factors and fluxes of the in-core irradiation positions are strongly affected by burnup. -- Abstract: The fundamental advantage and main reason to use Monte Carlo methods for burnup calculations is the possibility to generate extremely accurate burnup dependent one group cross-sections and neutron fluxes for arbitrary core and fuel geometries. Yet, a set of values determined for a material at a given position and time remains accurate only in a local region, in which neutron spectrum and flux vary weakly — and only for a limited period of time, during which changes of the local isotopic composition are minor. This paper presents the approach of fuel burnup evaluation used at the Moroccan TRIGA MARK II research reactor. The approach is essentially based upon the utilization of BUCAL1, an in-house developed burnup code. BUCAL1 is a FORTRAN computer code designed to aid in analysis, prediction, and optimization of fuel burnup performance in nuclear reactors. The code was developed to incorporate the neutron absorption reaction tally information generated directly by MCNP5 code in the calculation of fissioned or neutron-transmuted isotopes for multi-fueled regions. The fuel cycle length and changes in several core parameters such as: core excess reactivity, control rods position, fluxes at the irradiation positions, axial and radial power factors and other parameters are estimated. Besides, this study gives valuable insight into the behavior of the reactor and will ensure better utilization and operation of the reactor during its life-time and it will allow the establishment of

  8. Effective cross sections of U-235 and Au in a TRIGA-type reactor core

    International Nuclear Information System (INIS)

    Harasawa, S.; Auu, G.A.

    1992-01-01

    The dependence of effective cross sections of gold and uranium for neutron spectrum in Rikkyo University Reactor (TRIGA Mark- II, RUR) fuel cell was studied using computer calculations. The dependence of thermal neutron spectrum with temperature was also investigated. The effective cross section of gold in water of the fuel cell at 32degC was 90.3 barn and the fission cross section of U-235, 483 barn. These two values are similar to the cross sections for neutron energy of 0.034 eV. (author)

  9. Calculation of fundamental parameters for the dynamical study of TRIGA-3-Salazar reactor (Mixed reactor core)

    International Nuclear Information System (INIS)

    Viais J, J.

    1994-01-01

    Kinetic parameters for dynamic study of two different configurations, 8 and 9, both with standard fuel, 20% enrichment and Flip (Fuel Life Improvement Program with 70% enrichment) fuel, for TRIGA Mark-III reactor from Mexico Nuclear Center, are obtained. A calculation method using both WIMS-D4 and DTF-IV and DAC1 was established, to decide which of those two configurations has the best safety and operational conditions. Validation of this methodology is done by calculate those parameters for a reactor core with new standard fuel. Configuration 9 is recommended to be use. (Author)

  10. Data acquisition system for the 3 MW TRIGA reactor at AERE Savar

    International Nuclear Information System (INIS)

    Abudl Ahad, A.O.M.

    1998-01-01

    A 3 MW TRIGA Mark II research reactor control console has been studied in detail and the channels have been selected for monitoring, display and record using the microcomputer. Information from these channels are fed to the computer through hardware like buffer, AD converter, multiplexer, etc. for continues display and permanent records using video monitor, printer and diskettes. Besides, the information from the console, other information like operating time, power, total burnup of fuel, operating persons, etc. are also available, with very little modifications in both hardware and software, the data logging system is now running successfully. (author)

  11. Enrichment measurement in TRIGA type fuels

    International Nuclear Information System (INIS)

    Aguilar H, F.; Mazon R, R.

    2001-05-01

    The Department of Energy of the United States of North America, through the program 'Idaho Operations Nuclear Spent Fuel Program' of the Idaho National Engineering and Environmental Laboratory (INEEL), in Idaho Falls; Idaho USA, hires to Global Technologies Inc. (GTI) to develop a prototype device of detection enrichment uranium (DEU Detection of Enrichment of Uranium) to determine quantitatively the enrichment in remainder U-235 in a TRIGA fuel element at the end of it useful life. The characteristics of the prototype developed by GTI are the following ones: It allows to carry out no-destructive measurements of TRIGA type fuel. Easily transportable due to that reduced of it size. The determination of the enrichment (in grams of U-235) it is obtained with a precision of 5%. The National Institute of Nuclear Research (ININ), in its facilities of the Nuclear Center of Mexico, it has TRIGA type fuel of high and low enrichment (standard and FLIP) fresh and with burnt, it also has the infrastructure (hot cells, armor-plating of transport, etc) and qualified personnel to carry out the necessary maneuvers to prove the operation of the DEU prototype. For this its would be used standard type fuel elements and FLIP, so much fresh as with certain burnt one. In the case of the fresh fuels the measurement doesn't represent any risk, the fuels before and after the measurement its don't contain a quantity of fission products that its represent a radiological risk in its manipulation; but in the case of the fuels with burnt the handling of the same ones represents an important radiological risk reason why for its manipulation it was used the transport armor-plating and the hot cells. (Author)

  12. Static measurements at PUSPATI TRIGA Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Syed Nahar Bin Syed Hussin Shabuddin; Sharifuldin Bin Salleh, Mohd Amin; Harasawa, Susumu

    1985-06-01

    Static measurements at the PUSPATI TRIGA Reactor (RTP) were made to study the variation of its fuel temperature with reactor power. Some constants that relate power to fuel temperature behaviour were also determined. These constants are reflective of the coolling characteristics in the reactor core. Comparison was also made between the negative temperature coefficient of reactivity obtained from these measurements to those published in the Safety Analysis Report, SAR. The differences between these values are attributable to a delayed effect found in static measurements but not included in the SAR calculation which consider the prompt effect only.

  13. Arkansas Tech University TRIGA nuclear reactor

    International Nuclear Information System (INIS)

    Sankoorikal, J.; Culp, R.; Hamm, J.; Elliott, D.; Hodgson, L.; Apple, S.

    1990-01-01

    This paper describes the TRIGA nuclear reactor (ATUTR) proposed for construction on the campus of Arkansas Tech University in Russellville, Arkansas. The reactor will be part of the Center for Energy Studies located at Arkansas Tech University. The reactor has a steady state power level of 250 kW and can be pulsed with a maximum reactivity insertion of $2.0. Experience gained in dismantling and transporting some of the components from Michigan State University, and the storage of these components will be presented. The reactor will be used for education, training, and research. (author)

  14. Safety Management at PUSPATI TRIGA Reactor (RTP)

    International Nuclear Information System (INIS)

    Ligam, A.S.; Zarina Masood; Ahmad Nabil Abdul Rahim

    2011-01-01

    Adequate safety measures and precautions, which follow relevant safety standards and procedures, should be in place so that personnel safety is assured. Nevertheless, the public, visitor, contractor or anyone who wishes to enter or be in the reactor building should be well informed with the safety measures applied. Furthermore, these same elements of safety are also applied to other irradiation facilities within the premises of Nuclear Malaysia. This paper will describes and explains current safety management system being enforced especially in the TRIGA PUSPATI Reactor (RTP) namely radiation monitoring system, safety equipment, safe work instruction, and interconnected internal and external health, safety and security related departments. (author)

  15. Operating experiences at the Finnish TRIGA reactor

    International Nuclear Information System (INIS)

    Salmenhaara, Seppo

    1988-01-01

    The Finnish TRIGA reactor has been in operation since March 1962. There are still 57 original Al-clad fuel elements in the core. So far we have had only two fuel cladding failures in 1981 and 1988. The first one was an Al-clad element and the second one a SS-clad. The low rate of fuel cladding failures has made it possible to use continuously also the Al-clad fuel elements. Although some conventional irradiations of certain type have been repeated successfully tens of times, new and unexpected incidents can still take place. As an example an event of a leaking irradiation capsule is described

  16. Stack Monitoring System At PUSPATI TRIGA Reactor

    International Nuclear Information System (INIS)

    Zamrul Faizad Omar; Mohd Sabri Minhat; Zareen Khan Abdul Jalil Khan; Ridzuan Abdul Mutalib; Khairulezwan Abdul Manan; Nurfarhana Ayuni Joha; Izhar Abu Hussin

    2014-01-01

    This paper describes the current Stack Monitoring System at PUSPATI TRIGA Reactor (RTP) building. A stack monitoring system is a continuous air monitor placed at the reactor top for monitoring the presence of radioactive gaseous in the effluent air from the RTP building. The system consists of four detectors that provide the reading for background, particulate, Iodine and Noble gas. There is a plan to replace the current system due to frequent fault of the system, thus thorough understanding of the current system is required. Overview of the whole system will be explained in this paper. Some current results would be displayed and moving forward brief plan would be mentioned. (author)

  17. The Impact of the Financial Crisis on Business Events at Natural Spas – The Slovenian Case

    OpenAIRE

    Janez Mekinc; Maša Budnar Radilovic; Boštjan Bizjak

    2012-01-01

    To determine the impact of the economic downturn that officially hit Slovenia in 2009 on the number, purpose, type and budgets of business events held at Slovenian natural spas. The study’s aim is to develop guidelines in the field of business events management at Slovenian natural spas. The research was carried out among key representatives from Slovenian natural spas who play an active role in managing events. Data were via a questionnaire that collected information about the purpose, numbe...

  18. AN EMPIRICAL SURVEY ON BASIC MILITARY TRAINING IN SLOVENIAN ARMED FORCES

    Directory of Open Access Journals (Sweden)

    Maja GARB

    2014-04-01

    Full Text Available Before employment in the Slovenian Armed Forces, all candidates have to finish basic military training. The empirical survey, done in 2011 on a group of military candidates in a Slovenian Training Center, checked the motivation, level of skills and education, attitudes of leaders, military identity, prestige and social support of these candidates. The results confirmed the skills’ and fighters’ orientation of Slovenian soldiers, but surprised with the paleomodern motivators for military job.

  19. Characterization of the Ljubljana TRIGA thermal column neutron radiographic facility

    International Nuclear Information System (INIS)

    Nemec, T.; Rant, J.; Kristof, E.; Glumac, B.

    1995-01-01

    An extensive characterization of the neutron beam of the existing neutron radiographic facility in the thermal column of the Ljubljana Triga Mark II research reactor is in progress. Neutron beam characteristics are needed to determine the effect of various neutron and gamma radiation on the neutron radiographic image. Commercially available medical scintillator converter screens based on Gd dioxy sulphite as well as Gd metal neutron converters are used to record neutron radiographic image. Thermal, epithermal and fast neutron fluxes were measured using Au and In activation detectors and cadmium ratio is determined. Neutron beam flux profiles are measured by film densitometry and by Au activation detector wires. By exposing films shielded by boral or lead plates individual contributions of thermal, epithermal neutrons and gamma radiation are estimated by densitometric measurements. By recording images of neutron image quality indicators BPI (Beam Purity Indicator) and SI (Sensitivity Indicator) produced by Riso, standard neutron radiography image characteristic are established. In gamma dosimetric measurements thermoluminescent detectors (CaF 2 Mn) are used. (author)

  20. IPR-R1 TRIGA research reactor decommissioning plan

    International Nuclear Information System (INIS)

    Andrade Grossi, Pablo; Oliveira de Tello, Cledola Cassia; Mesquita, Amir Zacarias

    2008-01-01

    The International Atomic Energy Agency (IAEA) is concerning to establish or adopt standards of safety for the protection of health, life and property in the development and application of nuclear energy for peaceful purposes. In this way the IAEA recommends that decommissioning planning should be part of all radioactive installation licensing process. There are over 200 research reactors that have either not operated for a considerable period of time and may never return to operation or, are close to permanent shutdown. Many countries do not have a decommissioning policy, and like Brazil not all installations have their decommissioning plan as part of the licensing documentation. Brazil is signatory of Joint Convention on the safety of spent fuel management and on the safety of radioactive waste management, but until now there is no decommissioning policy, and specifically for research reactor there is no decommissioning guidelines in the standards. The Nuclear Technology Development Centre (CDTN/CNEN) has a TRIGA Mark I Research Reactor IPR-R1 in operation for 47 years with 3.6% average fuel burn-up. The original power was 100 k W and it is being licensed for 250 k W, and it needs the decommissioning plan as part of the licensing requirements. In the paper it is presented the basis of decommissioning plan, an overview and the end state / final goal of decommissioning activities for the IPR-R1, and the Brazilian ongoing activities about this subject. (author)

  1. Medical and radiobiological applications at the research reactor TRIGA Mainz

    International Nuclear Information System (INIS)

    Hampel, G.; Grunewald, C.; Kratz, J.-V.; Schmitz, T.; Schutz, C.; Werner, S.; Appelman, K.; Moss, R.; Blaickner, M.; Nawroth, T.; Otto, G.; Schmidberger, H.

    2010-01-01

    At the University of Mainz, Germany, a boron neutron capture therapy (BNCT) project has been started with the aim to expand and advance the research on the basis of the TAOrMINA protocol for the BNCT treatment of liver metastases of colorectal cancer. Irradiations take place at the TRIGA Mark II reactor. Biological and clinical research and surgery take place at the University and its hospital of Mainz. Both are situated in close vicinity to each other, which is an ideal situation for BNCT treatment, as similarly performed in Pavia, in 2001 and 2003. The application of BNCT to auto-transplanted organs requires development in the methodology, as well as regard to the irradiation facility and is part of the complex, interdisciplinary treatment process. The additional high surgical risk of auto-transplantation is only justified when a therapeutic benefit can be achieved. A BNCT protocol including explantation and conservation of the organ, neutron irradiation and re-implantation is logistically a very challenging task. Within the last years, research on all scientific, clinical and logistical aspects for the therapy has been performed. This includes work on computational modelling for the irradiation facility, tissue and blood analysis, radiation biology, dosimetry and surgery. Most recently, a clinical study on boron uptake in both healthy and tumour tissue of the liver and issues regarding dosimetry has been started, as well as a series of cell-biology experiments to obtain concrete results on the relative biological effectiveness (RBE) of ionizing radiation in liver tissue. (author)

  2. New burnup calculation of TRIGA IPR-R1 reactor

    International Nuclear Information System (INIS)

    Meireles, Sincler P. de; Campolina, Daniel de A.M.; Santos, Andre A. Campagnole dos; Menezes, Maria A.B.C.; Mesquita, Amir Z.

    2015-01-01

    The IPR-R1 TRIGA Mark I research reactor, located at the Nuclear Technology Development Center - CDTN, Belo Horizonte, Brazil, operates since 1960.The reactor is operating for more than fifty years and has a long history of operation. Determining the current composition of the fuel is very important to calculate various parameters. The reactor burnup calculation has been performed before, however, new techniques, methods, software and increase of the processing capacity of the new computers motivates new investigations to be performed. This work presents the evolution of effective multiplication constant and the results of burnup. This new model has a more detailed geometry with the introduction of the new devices, like the control rods and the samarium discs. This increase of materials in the simulation in burnup calculation was very important for results. For these series of simulations a more recently cross section library, ENDF/B-VII, was used. To perform the calculations two Monte Carlo particle transport code were used: Serpent and MCNPX. The results obtained from two codes are presented and compared with previous studies in the literature. (author)

  3. The role of TRIGA reactors in pure and applied nuclear research outside the United States in the last couple of years

    International Nuclear Information System (INIS)

    Rollier, M.A.

    1972-01-01

    The last two years trend of research in European TRIGA plants, which reported to the 1970 TRIGA Owners' Conference in Helsinki, is presented. The report discusses also new TRIGA plants in Europe, 1971-72; Research at TRIGA plants and new TRIGA reactors outside Europe and the U.S.A., 1971-72; Safety, health, environment, egomania and TRIGA reactors

  4. Communication of Slovenian Tourism Workers with Italian guests

    Directory of Open Access Journals (Sweden)

    Silva Gomzi Praprotnik

    2016-12-01

    Full Text Available For an Italian guest, getting to know Slovenia as a tourist destination is inevitably connected with getting to know the Slovenian cuisine. Italians are a nation eagerly developing the culture of food, and therefore the gastronomic offer in a certain environment and at a certain time is for them often the basis for a comprehensive perception of the said destination. A good offer, a suitable marketing and an attractive presentation of typical Slovenian dishes play an important role in getting to know natural and cultural heritage as they can widen the knowledge about people and places, eliminate prejudice and strengthen intercultural cooperation. Kind and professional staff, knowledge of the language, civilisation, cultural habits, and differences may be the factors contributing to the assertion of local products and services, and to educating the users of restaurant and tourism services.

  5. The effectiveness of performance measuring in Slovenian public libraries

    Directory of Open Access Journals (Sweden)

    Silva Novljan

    1997-01-01

    Full Text Available The article describes methods of performance measuring in Slovenian public libraries, and calls attention to the problems attached to it. The argued presumption is that the performance measuring carried out on the state level, is not always a sufficient and adequate foundation for plarming of the developmenl and functioning of an individual library which has to cater for the needs and wishes of the population in a certain area.

  6. Facing the Future: Slovenian Armed Forces Officer Corps and Professionalism

    Science.gov (United States)

    2011-12-16

    United Nations WWW World Wide Web YPA Yugoslav People’s Army ix ILLUSTRATIONS Page Figure 1. Professional officer...and “profesionalni.” 56Anton Zabkar, “Ahilova Peta Sistema Izobrazevanja Castnikov (Razprava)” [The Achilles’ heels of the education system for SAF...Primerjalna Analiza Urejanja Sistema Plac Pripadnikov Obrambnih Sil” [Comparative analysis of salary systems of armed forces members], Slovenian Armed

  7. Restaurant quality: the case of Central Slovenian region

    OpenAIRE

    Uran Maravić, Maja

    2016-01-01

    The purpose – This study has two key goals. The first part presents and compares different expert systems for assessing quality in the restaurants alongside the Ljubljana Quality Selection assessment methodology - LQS. In the second part, this study presents the results of a restaurant assessment in the Central Slovenian region using the LQS methodology. Design/methodology – In the first part of the study, we compare restaurant assessment systems through different criteria. In the second p...

  8. Business annual planning and controlling in Slovenian managerial practice

    OpenAIRE

    Pučko, Danijel; Čater, Tomasž

    2001-01-01

    Management process is usually segmented into planning, organizing, leading and controlling. The first and the last of these subprocesses are analyzed in the paper from the economic and managerial viewpoint as they occurr in Slovenian enterprise practice. The focus is on empirical research on a tactical level. Business analysis, tactical planning and controlling are the core issues analyzed in the article. The paper builds heavily on presenting empirical findings regarding the empirical system...

  9. Industrial structure and privatisation of the Slovenian electricity industry

    International Nuclear Information System (INIS)

    Hrovatin, N.

    1999-01-01

    The paper first analyses the existing structure of the Slovenian electricity industry and gives recommendations for its restructuring so as to conform to efficiency criteria and to comply with European Union provisions on the internal European electricity market. Then the paper outlines the necessity for privatisation and draws some conclusions on it such as determination of market values companies, the proportion for sale, privatisation methods and the general public's participation [it

  10. Preparation for shipment of spent TRIGA fuel elements from the research reactor of the Medical University of Hannover

    International Nuclear Information System (INIS)

    Hampel, Gabriele; Cordes, Harro; Ebbinghaus, Kurt; Haferkamp, Dirk

    1998-01-01

    In the early seventies a research reactor of type TRIGA Mark I was installed in the Department of Nuclear Medicine at the Medical University of Hannover (MHH) for the production of isotopes with short decay times for medical use. Since new production methods have been developed, the reactor has become obsolete and the MHH decided to decommission it. Probably in the second quarter of 1999 all 76 spent TRIGA fuel elements will be shipped to Idaho National Engineering and Environmental Laboratory (INEEL), USA, in one cask of type GNS 16. Due to technical reasons within the MHH a special Mobile Transfer System, which is being developed by the company Noell-KRC, will be used for reloading the fuel elements and transferring them from the reactor to the cask GNS 16. A description of the main components of this system as well as the process for transferring the fuel elements follows. (author)

  11. Establishing a site for A Slovenian LILW repository - 16151

    International Nuclear Information System (INIS)

    VIRSEK, SANDI; SPILER, JANJA; VESELIC, MIRAN

    2009-01-01

    In this paper we will describe the practice and siting process for a LILW repository in Slovenia. Slovenia is a small country, and, consequently, its nuclear programme is small. It does include almost everything that large programmes have, but we still do not have a repository. In 2004, the Slovenian Radwaste management agency (ARAO) initiated a new procedure to find a proper location for a LILW repository. ARAO asked all Slovenian communities to participate. All communities have the option to withdraw from the process until they have approved the site. We received eight responses, and we prepared methodologies with different parameters to evaluate all potential sites. All sites were assessed by Slovenian experts, and determinations were based on using prepared methodologies. On the basis of their expert opinions, we prepared a pre-feasibility study and chose the three most suitable sites. With these three we continued the process. After that time, one of the communities withdrew from the procedure, and another one reversed its proposed site and proposed a new one. For the third site we continued with the programme, and we prepared a feasibility study with a Strategic Environmental Impact Assessment and preliminary safety calculations for the comparison of different concepts of disposal units. If everything goes according to the plan for this site and the concept, we expect site approval in the first half of 2009. After that, we will start preparing everything necessary for building permission. (authors)

  12. Slovenica: professional novelties of the new Slovenian Library Act

    Directory of Open Access Journals (Sweden)

    Eva Kodrič-Dačić

    2002-01-01

    Full Text Available The new Slovenian Library Act introduces the term Slovenica to describe the most essential part of the national library collection. This term was introduced to Slovenian librarianship in the early thirties of the past century, but the collection of Slovenica was founded more than a hundred years before that time in the Lyceum Library, the predecessor of the present National and University Library. The criteria for the selection of the collection were influenced by the state regulated implementation of local studies collections into the lyceum and university libraries on one hand and by the growing national consciousness of Slovenian librarians on the other. This process began in the last quarter of the eighteenth century, when local studies material was prescribed in instructions regulating the integration of library materials from the dissolved monastery libraries to the state supported lyceum and university libraries.These instructions were upgraded by the explicit guidelines concerning local studies collections in the nineteenth century to finally evolve into a legally recognised activity of the national library after the Second World War.

  13. Thirteen[th] European TRIGA users conference. Proceedings

    International Nuclear Information System (INIS)

    1994-01-01

    The conference covers topic related to TRIGA reactor, such as reactor operation and maintenance experience - safety aspects; research activities and applications; boron neutron capture therapy (BNCT) projects and other design operational and safety issues

  14. Ten years of TRIGA reactor research at the University of Texas

    International Nuclear Information System (INIS)

    O'Kelly, Sean

    2002-01-01

    The 1 MW TRIGA Research Reactor at the Nuclear Engineering Teaching Laboratory is the second TRIGA at the University of Texas at Austin (UT). A small (10 kW-1963, 250 kW-1968) TRIGA Mark I was housed in the basement of the Engineering Building until is was shutdown and decommissioned in 1989. The new TRIGA Mark II with a licensed power of 1.1 MW reached initial criticality in 1992. Prior to 1990, reactor research at UT usually consisted of projects requiring neutron activation analysis (NAA) but the step up to a much larger reactor with neutron beam capability required additional personnel to build the neutron research program. The TCNS is currently used to perform Prompt Gamma Activation Analysis to determine hydrogen and boron concentrations of various composite materials. The early 1990s was a very active period for neutron beam projects at the NETL. In addition to the TCNS, a real-time neutron radiography facility (NIF) and a high-resolution neutron depth profiling facility (NDP) were installed in two separate beam ports. The NDP facility was most recently used to investigate alpha damage on stainless steel in support of the U.S. Nuclear Weapons Stewardship programs. In 1999, a sapphire beam filter was installed in the NDP system to reduce the fast neutron flux at the sample location. A collaborative effort was started in 1997 between UT-Austin and the University of Texas at Arlington to build a reactor-based, low-energy positron beam (TIPS). The limited success in obtaining funding has placed the project on hold. The Nuclear and Radiation Engineering Program has grown rapidly and effectively doubled in size over the past 5 years but years of low nuclear research funding, an overall stagnation in the U.S. nuclear power industry and a persuasive public distrust of nuclear energy has caused a precipitous decline in many programs. Recently, the U.S. DOE has encouraged University Research Reactors (URR) in the U.S. to collaborate closely together by forming URR

  15. Twelfth European TRIGA users conference. Papers and abstracts

    International Nuclear Information System (INIS)

    2008-01-01

    The Twelfth European TRIGA Users Conference was held in Pitesti, Romania, on September 28 - October 1, 1992, under the sponsorship of the Institute for Nuclear Research. The papers which follow in this document are presented in the same order as listed in the Conference Program. All papers which were received for publication (44) have been included. Those papers which were presented but not received for publication are presented in abstract form (3). The European TRIGA9 Owners' Group was fortunate to be hosted by the owners and users of the world's largest TRIGA reactor - the 14-MW Romanian research and test reactor. For too many years it has been impossible to enjoy open interactions with the Romanian researchers. By hosting the 1992 European TRIGA Users' Conference in Romania, the Romanians accomplished a breakthrough in the exchange of TRIGA reactor technology. It was very interesting for the Conference attendees from the West to learn about the large scope of excellent work conducted in Romania, especially at the Institute of Nuclear Research in Pitesti. Similarly, it was fortunate that a large attendance of Romanian researchers from many institutes, universities, and government agencies could attend the Conference and interact with their counterparts from outside Romania. The proceedings of the conference were structured onto the following 6 subject matters: - Opening Session and Introduction; - Session I, Operating and Maintenance Experience (10 papers); - Session II, Reactor Physics And Fuel Utilization (11 papers); - Session III, Instrumentation and Control (5 papers); - Session IV, Irradiation Facilities, Experimental Accessories (8 papers); - Session V, Applications, New Development of TRIGA Concept (6 papers). The document is completed with the abstracts of 3 contributions. A number of 19 experts from Austria, Germany, Italy, United States, Turkey, Morocco, England, Slovenia and Albania, that use TRIGA reactors, and Romania attended the conference. The

  16. 2nd world TRIGA users conference. Conference volume

    International Nuclear Information System (INIS)

    2004-01-01

    This conference was organized by the Atomic Institute of the Austrian Universities (University of Technology Vienna), it was devoted to present results in the operation of TRIGA research reactors. The main general topics were: a) reactor operation experience, b)neutron and solid state physics, c) radiochemistry and activation analysis, d) medical applications (boron neutron capture therapy, labeled compounds), e) reactor related experiments and calculations, f) waste management and decommissioning of TRIGA reactors. (nevyjel)

  17. 3. world TRIGA users conference. Papers and abstracts

    International Nuclear Information System (INIS)

    2006-01-01

    The Conference is focused on TRIGA reactors operation and applications. The main topics are: use of the reactor as a research tool; inspection of spent fuel elements; integrity of fuel rods cladding checks; evaluation of corrosion of aluminum-base fuel cladding materials; Pitting behavior of Aluminum alloys; Monte Carlo simulation of TRIGA: reactivity worth, burnup, flux and power; irradiation facilities; thermal hydraulics analyses etc

  18. 2nd world TRIGA users conference. Conference volume

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    This conference was organized by the Atomic Institute of the Austrian Universities (University of Technology Vienna), it was devoted to present results in the operation of TRIGA research reactors. The main general topics were: a) reactor operation experience, b)neutron and solid state physics, c) radiochemistry and activation analysis, d) medical applications (boron neutron capture therapy, labeled compounds), e) reactor related experiments and calculations, f) waste management and decommissioning of TRIGA reactors. (nevyjel)

  19. Operational experience with the TRIGA reactor of the University of Pavia

    International Nuclear Information System (INIS)

    Borio di Tigliole, A.; Alloni, D.; Cagnazzo, M.; Coniglio, M.; Lana, F.; Losi, A.; Magrotti, G.; Manera, S.; Marchetti, F.; Pappalardo, P.; Prata, M.; Salvini, A.; Scian, G.; Vinciguerra, G.

    2008-01-01

    The TRIGA Mark II research reactor of the University of Pavia is in operation since 1965. The annual operational time at nominal power (250 kW) is in the range of 300 - 400 hours depending upon the time schedule of some experiments and research activities. The reactor is mainly used for NAA activities and BNCT research. Few tens of hours per year are dedicated also to electronic devices irradiation and student training courses. Few homemade upgrading of the reactor were realized in the past two years: components of the secondary/tertiary cooling circuit were substituted and a new radiation area monitoring system was installed. Also the Instrumentation and Control (I and C) system was almost completely refurbished. The presentation describes the major extraordinary maintenance activities implemented and the status of main reactor systems: - The I and C System: complete substitution, channel-by-channel without changing the operating and safety logics; - Tertiary and secondary water-cooling circuits: complete substitution of the tertiary water-cooling circuit and partial substitution of the components of the secondary water-cooling circuit; - Reactor Building Air Filtering and Ventilation System: installation of a computerized air filtering and ventilation system; - Radiation Area Monitoring System: new system based on a commercial micro-computer and an home-made software developed on Lab-View platform. The system is made of a network of different instruments coupled, trough a serial bus line RS232, with a data acquisition station; - Fuel Elements: at the moment, the core is made of 48 Aluminium clad and 34 SST clad TRIGA fuel elements controlled periodically for their elongation and/or bowing. All components and systems undergo ordinary maintenance according to the Technical Prescriptions and to the 'Good Practice Procedures'. In summary, the TRIGA reactor of the University of Pavia shows a very good technical state and, at the moment, there are no political or

  20. Characteristics and uses of a 250 kW TRIGA reactor

    International Nuclear Information System (INIS)

    Dimic, V.

    1985-01-01

    The 250 kW TRIGA Mark II reactor is a light water reactor with solid fuel elements in which the zirconium hydride moderator is homogeneously distributed between enriched uranium. Therefore the reactor has the large prompt negative temperature coefficient of reactivity, the fuel also has very high retention of radioactive fission products. The reactor core is a cylindrical configuration with an annular graphite reflector. The experimental facilities include a rotary specimen rack, a central incore radiation thimble, a pneumatic transfer system, and pulsing capability. Other experimental facilities include two radial and two tangential beam tubes, a graphite thermal column, and a graphite thermalizing column. At the steady state power of 250 kW the peak flux is 1x10 13 n/cm 2 s in the central test position. In addition, pulsing to about 2000 MW is usually provided giving peak fluxes of about 2x10 16 n/cm 2 sec. All TRIGA reactors produce a core-average thermal neutron flux of about 10 7 n.v per watt. Only with very large accelerators could such a high neutron flux be achieved. In order to give an appreciation for the research conducted at research reactors, the types of research could be summarized as follows: thermal neutron scattering, neutron radiography, neutron and nuclear physics, activation analysis, radiochemistry, biology and medicine, and teaching and training. Typical applied research with a 250 kW reactor has been conducted in medicine in biology, archeology, metallurgy and materials science, engineering and criminology. It is well known that research reactors have been used routinely to produce isotopes for industry and medicine. In some instances, reactors are the preferred method of isotope production. We can conclude that the 250 kW TRIGA research reactor is a useful and wide ranging source of radiation for basic and applied research. The operation cost for this instrument is relatively low. (author)

  1. Neutron flux measurements in PUSPATI Triga Reactor

    International Nuclear Information System (INIS)

    Gui Ah Auu; Mohamad Amin Sharifuldin Salleh; Mohamad Ali Sufi.

    1983-01-01

    Neutron flux measurement in the PUSPATI TRIGA Reactor (PTR) was initiated after its commissioning on 28 June 1982. Initial measured thermal neutron flux at the bottom of the rotary specimen rack (rotating) and in-core pneumatic terminus were 3.81E+11 n/cm 2 sec and 1.10E+12n/cm 2 sec respectively at 100KW. Work to complete the neutron flux data are still going on. The cadmium ratio, thermal and epithermal neutron flux are measured in the reactor core, rotary specimen rack, in-core pneumatic terminus and thermal column. Bare and Cadmium covered gold foils and wires are used for the above measurement. The activities of the irradiated gold foils and wires are determined using Ge(Li) and hyperpure germinium detectors. (author)

  2. Physics and kinetics of TRIGA reactor

    International Nuclear Information System (INIS)

    Boeck, H.; Villa, M.

    2007-01-01

    This training module is written as an introduction to reactor physics for reactor operators. It assumes the reader has a basic, fundamental knowledge of physics, materials and mathematics. The objective is to provide enough reactor theory knowledge to safely operate a typical research reactor. At this level, it does not necessarily provide enough information to evaluate the safety aspects of experiment or non-standard operation reviews. The material provides a survey of basic reactor physics and kinetics of TRIGA type reactors. Subjects such as the multiplication factor, reactivity, temperature coefficients, poisoning, delayed neutrons and criticality are discussed in such a manner that even someone not familiar with reactor physics and kinetics can easily follow. A minimum of equations are used and several tables and graphs illustrate the text. (author)

  3. Status of the TRIGA-LASER experiment

    Energy Technology Data Exchange (ETDEWEB)

    Gorges, C., E-mail: chgorges@uni-mainz.de; Kaufmann, S., E-mail: s.kaufmann@uni-mainz.de [Technische Universität Darmstadt, Institut für Kernphysik (Germany); Geppert, Ch. [Johannes Gutenberg-Universität Mainz, Institut für Kernchemie (Germany); Krämer, J. [Technische Universität Darmstadt, Institut für Kernphysik (Germany); Sánchez, R. [GSI Helmholtzzentrum für Schwerionenforschung (Germany); Nörtershäuser, W. [Technische Universität Darmstadt, Institut für Kernphysik (Germany)

    2017-11-15

    We report on the newly developed control system called TRITON and the new data acquisition called TILDA as well as on improved isotope shift measurements of the isotopes {sup 40,42,44,48}Ca in the 4s 2S1/2 → 4p 2P3/2 (D2) transition at the TRIGA-LASER experiment in Mainz using collinear laser spectroscopy. Well known isotope shift measurements in the 4s 2S1/2 → 4p 2P1/2 (D1) transition act as calibration points to reduce the uncertainties in the D2-line to provide reference values for the determination of nuclear charge radii and quadrupole moments of neutron rich calcium isotopes at COLLAPS.

  4. Research activities at the TRIGA Mainz

    International Nuclear Information System (INIS)

    Eberhardt, K.

    1994-01-01

    The experimental programme at the TRIGA Mainz covers a wide range of applications in different fields. Two of the four beam tubes are used for the development of fast and mainly continuous chemical separation procedures. These procedures are applied for the investigation of short-lived nuclides and for studies of the chemical behaviour of the heaviest elements. At the third beam tube an on-line mass-separator facility with a microwave-induced plasma as an ion source is installed. Very recently the fourth beam tube has been modified for the production of polarized neutrons by interaction with optically pumped 3 He atoms. The other irradiation facilities are used for Neutron Activation Analysis (NAA) of different samples, among them geological and environmental ones, tracer production for chemical investigations, neutron irradiations of rat brain tissue to explore the utility of 157 Gd for cancer therapy and γ-ray irradiations for biological purposes. (author)

  5. Pneumatic transport systems for TRIGA reactors

    International Nuclear Information System (INIS)

    Bolton, John A.

    1970-01-01

    Main parameters and advantages of pneumatically operated systems, primarily those operated by gas pressure are discussed. The special irradiation ends for the TRIGA reactor are described. To give some idea of the complexity of some modern systems, the author presents the large system currently operating at the National Bureau of Standards in Washington. In this system, 13 stations are located throughout the radiochemistry laboratories and three irradiation ends are located in the reactor, which is a 14-megawatt unit. The system incorporates practically every fail-safe device possible, including ball valves located on all capsule lines entering the reactor area, designed to close automatically in the event of a reactor scram, and at that time capsules within the reactor would be diverted by means of switches located on the inside of the reactor wall. The whole system is under final control of a permission control panel located in the reactor control room. Many other safety accessories of the system are described

  6. Stretch Marks

    Science.gov (United States)

    ... completely without the help of a dermatologist or plastic surgeon. These doctors may use one of many types of treatments — from actual surgery to techniques like microdermabrasion and laser treatment — to reduce the appearance of stretch marks. These techniques are ...

  7. Fuel management for TRIGA reactor operators

    International Nuclear Information System (INIS)

    Totenbier, R.E.; Levine, S.H.

    1980-01-01

    One responsibility of the Supervisor of Reactor Operations is to follow the TRIGA core depletion and recommend core loading changes for refueling and special experiments. Calculations required to analyze such changes normally use digital computers and are extremely difficult to perform for one who is not familiar with computer language and nuclear reactor diffusion theory codes. The TRICOM/SCRAM program developed to perform such calculations for the Penn State TRIGA Breazeale Reactor (PSBR), has a very simple input format and is one which can be used by persons having no knowledge of computer codes. The person running the program need not understand computer language such as Fortran, but should be familiar with reactor core geometry and effects of loading changes. To further simplify the input requirements but still allow for all of the studies normally needed by the reactor operations supervisor, the options required for input have been isolated to two. Given a master deck of computer cards one needs to change only three cards; a title card, core energy history information card and one with core changes. With this input, the program can provide individual fuel element burn-up for a given period of operation and the k eff of the core. If a new loading is desired, a new master deck containing the changes is also automatically provided. The life of a new core loading can be estimated by feeding in projected core burn-up factors and observing the resulting loss in individual fuel elements. The code input and output formats have now been made sufficiently convenient and informative as to be incorporated into a standard activity for the Reactor Operations Supervisor. (author)

  8. The TRIGA in virtual classroom for training

    International Nuclear Information System (INIS)

    Plata M, A. C.; Morales S, J. B.; Salazar S, E.

    2008-01-01

    The research nuclear reactors have been fundamental part in the evolution of the nuclear power plants and they have been used in the training for the obtaining of operation licenses of radioactive facilities. For purposes of training of professionals in nuclear engineering, it is interesting to know the benefit that can be obtained by means of the virtual representation of a research nuclear reactor TRIGA, with which they are possible the practice to be realized them but common that to date they are carried out in different nuclear facilities of training throughout the world. The simulation has become a valuable tool in the personal preparation, having obtained ambient and very approximate situations to the reality. The physical models of kinetics of neutrons, heat transfer, Cherenkov effect, dynamics of the xenon, as well as the virtual instrumentation is contemplated in this development. The instrumentation and control panels of a research reactor, failures waited for in the use of this equipment, physical consequences to instruments, virtual personnel and facilities, as well as the administrative and legal aspects that it requires to meet an authorized operator, must be available and they are considered in the first virtual approach. The obtaining of the reactor time constant comprises of the mathematical model that provides to the operator of a direct way the knowledge of the changes of power. The coolant and moderator are modeled as well as the retardations that appear in the measurements and controls that can be introduced from the virtual console. In the simulator the four possible states of operation of the TRIGA can be had. At the moment also the monitoring can be realized and control in remote form, thus the control and supervision interface for the remote operation will be analyzed in their benefits and possible risks in the instruction processes. (Author)

  9. RELAP5 model for TRIGA 14 MWt

    International Nuclear Information System (INIS)

    Negut, Gheorghe; Prisecaru, Ilie)

    2003-01-01

    The ICN TRIGA facility was commissioned at the beginning of 1980. Since that time the 14 MW Material Test Reactor was used extensively for various tests, experiments and basic research. There were provided a 100 kW loop and natural convection capsules to test CANDU type fuel and structural materials as Zircaloy as well as medical and industrial radioisotopes production facilities. The first load of High Enriched Uranium (HEU) fuel, mostly was exhausted and in the '90 there was necessary a replacement with Low Enriched Uranium (LEU) fuel. The original configuration of 29 HEU fuel bundles is now replaced with a HEU - LEU mixed core of 35 fuel bundles. This process involved the revision of Safety Analysis Report.The paper presents the analysis of Loss of Fluid Accident (LOFA) and the comparison with the results obtained during commissioning phase. A simple model of the TRIGA core was developed with the aid of RELAP5MOD3.2 code. The RELAP5 documented the flow reversal and natural convection establishment, and the model proved a useful and accurate instrument for thermal hydraulic analysis. Presented are the RELAP5 model for the TRIGA reactor and a LOFA accident analysis. The following results and conclusions concerning the LOFA tests with emergency pump off after 15 minutes and at start of the test are presented. In the first test TRIGA reactor is operated at the nominal power of 14 MW and the main pumps flow rate is 700 kg/sec. The main pumps are stopped and in 10 seconds the flow rate reaches 22 kg/sec, the emergency pump flow rate. The emergency pump is stopped after 15 minutes from the LOFA test initiation. The reactor is tripped by the low flow rate signal at the level of 473 kg/sec. The core flow is reversed after the 5 seconds and the core is cooled by natural convection. After 425 seconds from the LOFA initiation the residual power level is sufficiently low, so, the flow is reversed once again and the residual heat is removed by the emergency pump flow in

  10. Environmental state of the Slovenian part of the Adriatic Sea

    Directory of Open Access Journals (Sweden)

    Valentina Brečko Grubar

    2010-06-01

    Full Text Available Slovenian part of the Adriatic Sea is its most northern part which occupies approximately 200 km2 and is a part of the wider Gulf of Trieste. Slovenian coast consists of 47 kilometers of mostly steep, abrasive marl and sandstone coast. Low accumulation coast is located only at the mouths of the watercourses and represents but a smaller portion, whereas the smallest part is occupied by the limestone abrasion coast. Mainland coastal region is mostly hillside and has a very diverse relief, while plains, in smaller numbers, are located only in the lower parts of the river valleys. Slovenian sea indents the mainland by two larger gulfs: the Gulf of Koper and of Piran and is predominately very shallow. The average depth is around 18 m and the largest depth is 38 m at the Madona cape near Piran. Sea bottom is mostly covered by the thick layer of sediments deposited after the abrasion of the steep cliff coast and by the accumulation of the river alluvium. Due to its shallowness the sea is exposed to high temperature fluctuations and due to the fresh water influx also to the changes of its salinity. The circulation of the sea water is mainly induced by the tide and wind activities, mostly the Bora (strong north-easterly wind which significantly influences the vertical circulation of the water. Water current is weak and unstable. There is a large influx of nutrients into the Slovenian sea, resulting from the soil erosion, surface water influx, watercourses and direct emissions of waste waters into the sea. The consequence of the mentioned sea characteristics is a great landscape sensitivity of the coastal sea ecosystem. During summer the sea warms intensely and when accompanied by the weak water circulation, we are often witnessing the lack of oxygen in the deeper layers of the water, intensive algae growth and sea blooming, which points to exceeded self-cleaning (assimilation capacities of the marine ecosystem. The major polluters are the coastal towns

  11. Environmental state of the Slovenian part of the Adriatic Sea

    Directory of Open Access Journals (Sweden)

    Valentina Brečko Grubar

    2010-01-01

    Full Text Available Slovenian part of the Adriatic Sea is its most northern part which occupies approximately 200 km2 and is a part of the wider Gulf of Trieste. Slovenian coast consists of 47 kilometers of mostly steep, abrasive marl and sandstone coast. Low accumulation coast is located only at the mouths of the watercourses and represents but a smaller portion, whereas the smallest part is occupied by the limestone abrasion coast. Mainland coastal region is mostly hillside and has a very diverse relief, while plains, in smaller numbers, are located only in the lower parts of the river valleys. Slovenian sea indents the mainland by two larger gulfs: the Gulf of Koper and of Piran and is predominately very shallow. The average depth is around 18 m and the largest depth is 38 m at the Madona cape near Piran. Sea bottom is mostly covered by the thick layer of sediments deposited after the abrasion of the steep cliff coast and by the accumulation of the river alluvium. Due to its shallowness the sea is exposed to high temperature fluctuations and due to the fresh water influx also to the changes of its salinity. The circulation of the sea water is mainly induced by the tide and wind activities, mostly the Bora (strong north-easterly wind which significantly influences the vertical circulation of the water. Water current is weak and unstable. There is a large influx of nutrients into the Slovenian sea, resulting from the soil erosion, surface water influx, watercourses and direct emissions of waste waters into the sea. The consequence of the mentioned sea characteristics is a great landscape sensitivity of the coastal sea ecosystem. During summer the sea warms intensely and when accompanied by the weak water circulation, we are often witnessing the lack of oxygen in the deeper layers of the water, intensive algae growth and sea blooming, which points to exceeded self-cleaning (assimilation capacities of the marine ecosystem. The major polluters are the coastal towns

  12. Supervisory system to monitor the neutron flux of the IPR-R1 TRIGA research reactor at CDTN

    International Nuclear Information System (INIS)

    Pinto, Antonio Juscelino; Mesquita, Amir Zacarias; Tello, Cledola Cassia Oliveira

    2009-01-01

    The IPR-R1 TRIGA Mark I nuclear research reactor at the Nuclear Technology Development Center - CDTN (Belo Horizonte) is a pool type reactor. It was designed for research, training and radioisotope production. The International Atomic Energy Agency- IAEA - recommends the use of friendly interfaces for monitoring and controlling the operational parameters of nuclear reactors. This paper reports the activities for implementing a supervisory system, using LabVIEW software, with the purpose to provide the IPR-R1 TRIGA research reactor with a modern, safe and reliable system to monitor the time evolution of the power of its core. The use of the LabVIEW will introduce modern techniques, based on electronic processor and visual interface in video monitor, substituting the mechanical strip chart recorders (ink-pen drive and paper) that monitor the current neutrons flux, which is proportional to the thermal power supplied by reactor core. The main objective of the system will be to follow the evolution of the neutronic flux originated in the Linear and Logarithmic channels. A great advantage of the supervisory software nowadays, in relation to computer programs currently used in the facility, is the existence of new resources such as the data transmission and graphical interfaces by net, grid lines display in the graphs, and resources for real time reactor core video recordings. The considered system could also in the future be optimized, not only for data acquisition, but also for the total control of IPR-R1 TRIGA reactor(author)

  13. Verification of performance of the power percentage channel for the TRIGA Mark III reactor; Verificacion del funcionamiento del canal del porciento de potencia del reactor TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Paredes G, L C

    1991-10-15

    It was found that the response that gives the power percent channel is correct, given the positive results of the independent tests that were carried out to the gamma ionization chamber and the electronics associated to this channel. Regarding the gamma chamber, it was verified that the appropriate operation voltage is 800 V, and that for operations in stationary state to 1 MW during 2 h, presented maximum variations of 3%. Also it was determined that the degradation percentage in the sensitivity to the gamma radiation is 10.24%, because this chamber has not been changed since the reactor enters in operation at November 8, 1968 by what will be considered to short term the substitution of the same one due to the burnt that it presents. In connection with the electronics of the channel, it was simulated the response of the chamber for intervals of 6 h and in the 4 analyzed cases the response of the channel was lineal. (Author)

  14. Design and construction of the SIPPING for fuels of the TRIGA Mark III reactor; Diseno y construccion del SIPPING para combustibles del reactor TRIGA Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Castaneda J, G.; Delfin L, A.; Alvarado P, R.; Mazon R, R.; Ortega V, B. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: adl@nuclear.inin.mx

    2003-07-01

    The sipping technique, it has been used by several possessors of nuclear research reactors in its irradiated nuclear fuels, likewise in some fuel storage sites, with the objective of to determine the quantity of radioactivity that the fuel liberates in the means in that it is. The irradiated fuel in storage of some nuclear research reactors, its can have cracks that cross the cladding of the same one, generating the liberation of fission products that its need to determine to maintain safety measures appropriate as much as the fuel as of the facilities where they are. It doesn't exist until now, some method published for the non destructive sipping test technique. Based on that described, the Reactor Department of the National Institute of Nuclear Research, it has designed and built an inspection system of irradiated fuel that it will allow the detection of gassy fission products in site, and solids by means of the measurement of the activity of the Cs-137 contained in water samples. (Author)

  15. DO SLOVENIAN DEALERS USE TECHNIQUES FOR INCREASING THEIR TIPS?

    Directory of Open Access Journals (Sweden)

    Andrej Raspor

    2016-05-01

    Full Text Available In 1996 Michael Lynn introduced the idea that restaurant managers could increase tips for their waiters and thus increase turnover by training the waiters to engage tip-enhancing behaviours. Since then, the list of tip-enhancing behaviours has expanded. Therefore the potential to increase tips is more accessible. The purpose of this paper was to examine how Slovenian dealers use strategies to increase their tips. We tested fourteen techniques to increase tips. The study was carried out among 473 gaming employees, 279 of which are dealers, in the Slovenian gaming industry, in order to find out how they use these techniques and which of them can bring about an increase in their tips. The study showed that Slovenian dealers mostly do not use these techniques, and that the dealers who do use them tend to receive tips more often. The findings imply that managers and employees should be informed of these techniques in order to increase tips and their overall income. Practical implications are that we suggest that management considers these ideas for increasing flexibility and reducing the cost of work: (1 informing dealers on ways of increasing tips, (2 including the acquisition of this specific knowledge in their career plans, (3 carrying out a reform of the reward system which would include tips. Social implications will be shown in a higher gaming revenue. It is very likely – as shown in our research – that employees will receive higher wages as these will be topped up by tips. The state, in turn, will collect more taxes.

  16. Assessing users satisfaction with service quality in Slovenian public library

    Directory of Open Access Journals (Sweden)

    Igor Podbrežnik

    2016-07-01

    Full Text Available Purpose: A research was made into user satisfaction with regard to the quality of library services in one of the Slovenian public libraries. The aim was to establish the type of service quality level actually expected by the users, and to determine their satisfaction with the current quality level of available library services.Methodology: The research was performed by means of the SERVQUAL measuring tool which was used to determine the size and direction of the gap between the detected and the expected quality of library services among public library users.Results: Different groups of users provide different assessments of specific quality factors, and a library cannot satisfy the expectations of each and every user if most quality factors display discrepancies between the estimated perception and expectations. The users expect more reliable services and more qualified library staff members who would understand and allocate time for each user’s individual needs. The largest discrepancies from the expectations are detected among users in the under-35 age group and among the more experienced and skilled library users. The results of factor analysis confirm the fact that a higher number of quality factors can be explained by three common factors affecting the satisfaction of library users. A strong connection between user satisfaction and their assessment of the integral quality of services and loyalty has been established.Research restrictions: The research results should not be generalised and applied to all Slovenian public libraries since they differ in many important aspects. In addition, a non-random sampling method was used.Research originality/Applicability: The conducted research illustrates the use of a measuring tool that was developed with the aim of determining the satisfaction of users with the quality of library services in Slovenian public libraries. Keywords: public library, user satisfaction, quality of library services, user

  17. Organisational Factors of Rapid Growth of Slovenian Dynamic Enterprises

    Directory of Open Access Journals (Sweden)

    Pšeničny Viljem

    2013-01-01

    Full Text Available The authors provide key findings on the internal and external environmental factors of growth that affect the rapid growth of dynamic enterprises in relation to individual key organisational factors or functions. The key organisational relationships in a growing enterprise are upgraded with previous research findings and identified key factors of rapid growth through qualitative and quantitative analysis based on the analysis of 4,511 dynamic Slovenian enterprises exhibiting growth potential. More than 250 descriptive attributes of a sample of firms from 2011 were also used for further qualitative analysis and verification of key growth factors. On the basis of the sample (the study was conducted with 131 Slovenian dynamic enterprises, the authors verify whether these factors are the same as the factors that were studied in previous researches. They also provide empirical findings on rapid growth factors in relation to individual organisational functions: administration - management - implementation (entrepreneur - manager - employees. Through factor analysis they look for the correlation strength between individual variables (attributes that best describe each factor of rapid growth and that relate to the aforementioned organisational functions in dynamic enterprises. The research findings on rapid growth factors offer companies the opportunity to consider these factors during the planning and implementation phases of their business, to choose appropriate instruments for the transition from a small fast growing firm to a professionally managed growing company, to stimulate growth and to choose an appropriate growth strategy and organisational factors in order to remain, or become, dynamic enterprises that can further contribute to the preservation, growth and development of the Slovenian economy

  18. 7. biennial U.S. TRIGA users' conference. Papers and abstracts

    International Nuclear Information System (INIS)

    1980-01-01

    The conference covers the following topics: new developments in the TRIGA system; uses of microprocessors in control and monitoring and measurement of TRIGA performance parameters; safeguards, emergency planning, reactor standards; research facilities, fuel tests and calculations; TRIGA reactor parameters: emergency training

  19. CEOs’ Strategic Orientations in the Most Successful Slovenian Companies

    Directory of Open Access Journals (Sweden)

    Dario Berginc

    2014-09-01

    Full Text Available This article presents the concept of a CEO’s strategic orientation as one of the most important elements of the research into a company’s successfulness. Managerial perception is in many ways more important than environmental analysis, since CEOs determine their company’s future strategic orientations. A study of CEOs’ strategic orientations can provide better information regarding companies’ strategic orientations. We performed a qualitative study of CEOs from a sample of the most successful Slovenian ompanies. The research results indicate numerous commonalities between CEOs’ opinions and standpoints, as well as some differences in relation to the characteristics of the companies and industries in which they operate.

  20. Successful competitive strategies of large Croatian and Slovenian enterprises

    Directory of Open Access Journals (Sweden)

    Marin Buble

    2003-01-01

    Full Text Available In this research report, the authors identify and analyze the successful samples of strategic behaviour of large Croatian and Slovenian enterprises, as well as their similarities and dissimilarities. The research has encompassed the levels of corporate and business strategy (i.e. the strategy of a diversified firm and its strategic business units/areas, as well as the analysis of strategic performance and sources of competitive advantage. The research consists of two parts: the theoretical foundation for the analysis of the successful patterns of strategic behaviour and the empirical analysis, based on the primary data collected during the research project.

  1. Acute retroviral syndrome in Slovenian patients infected with HIV

    Directory of Open Access Journals (Sweden)

    Mateja Pirš

    2005-06-01

    Full Text Available Background: Two to six weeks after primary infection with HIV 50 to 90 percent of patients develop an acute retroviral syndrome which usually presents with mononucleosis or flu-like illness. Due to nonspecific symptoms ARS is frequently misdiagnosed.Patients and methods: Data of Slovenian patients with acute retroviral syndrome is shown, as well as their symptoms, approaches to management and diagnostic particularities of primary HIV infection.Conclusions: The combination of particular symptoms and epidemiological data should lead us to consider the possibility of an early HIV infection.

  2. &A, COMPETITION AND PERFORMANCE IN THE SLOVENIAN BANKING SYSTEM

    Directory of Open Access Journals (Sweden)

    Andreea Nicoleta Popovici

    2014-04-01

    Full Text Available The process of mergers and acquisitions is the main method used by financial institution to grow and to obtain better performance. The main effect of the implication of banks in mergers and acquisitions (M&A translates into a higher degree of market share of the banks and also that the small banks will soon become global banks. This article underlines the relationship between bank performance and degree of concentration of the Slovenian banking sector during 2006-2012 using a simple linear regression model.

  3. Slovenian experience from diagnostic angiography to interventional radiology

    International Nuclear Information System (INIS)

    Pavcnik, Dusan

    2014-01-01

    The purpose of writing this article is to document the important events and people in the first 50 years of diagnostic angiography and interventional radiology in Slovenia. During this period not only did the name of the institutions and departments change, but also its governance. This depicted the important roles different people played at various times in the cardiovascular divisions inside and outside of the diagnostic and interventional radiology. Historical data show that Slovenian radiology has relatively immediately introduced the new methods of interventional radiology in clinical practice

  4. Safety case for Slovenian LILW near-surface repository

    International Nuclear Information System (INIS)

    Viršek, Sandi; Špiler, Janja; Žagar, Tomaž

    2016-01-01

    Conclusions: • Repository provides the fulfillment of international and national legal requirements regarding treatment and disposal of LILW; • Repository improves the conditions for life extension for NPP Krško and offers synergetic effects for the second unit of NPP Krško; • Repository provides a basis for safe, economic and reliable use of radioactive sources in science, medicine and industry in Slovenia; • All economic calculations and comparisons show a clear advantage in case of a joint Slovenian and Croatian solution

  5. Conceptual Design of a Clinical BNCT Beam in an Adjacent Dry Cell of the Jozef Stefan Institute TRIGA Reactor

    International Nuclear Information System (INIS)

    Maucec, Marko

    2000-01-01

    The MCNP4B Monte Carlo transport code is used in a feasibility study of the epithermal neutron boron neutron capture therapy facility in the thermalizing column of the 250-kW TRIGA Mark II reactor at the Jozef Stefan Institute (JSI). To boost the epithermal neutron flux at the reference irradiation point, the efficiency of a fission plate with almost 1.5 kg of 20% enriched uranium and 2.3 kW of thermal power is investigated. With the same purpose in mind, the TRIGA reactor core setup is optimized, and standard fresh fuel elements are concentrated partly in the outermost ring of the core. Further, a detailed parametric study of the materials and dimensions for all the relevant parts of the irradiation facility is carried out. Some of the standard epithermal neutron filter/moderator materials, as well as 'pressed-only' low-density Al 2 O 3 and AlF 3 , are considered. The proposed version of the BNCT facility, with PbF 2 as the epithermal neutron filter/moderator, provides an epithermal neutron flux of ∼1.1 x 10 9 n/cm 2 .s, thus enabling patient irradiation times of nfast /φ epi -13 Gy.cm 2 /n and [overdot]D γ /φ epi -13 Gy.cm 2 /n), the in-air performances of the proposed beam are comparable to all existing epithermal BNCT facilities. The design presents an equally efficient alternative to the BNCT beams in TRIGA reactor thermal columns that are more commonly applied. The cavity of the dry cell, a former JSI TRIGA reactor spent-fuel storage facility, adjacent to the thermalizing column, could rather easily be rearranged into a suitable patient treatment room, which would substantially decrease the overall developmental costs

  6. Measured and calculated effective delayed neutron fraction of the IPR-R1 Triga reactor

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Rose Mary G.P.; Dalle, Hugo M.; Campolina, Daniel A.M., E-mail: souzarm@cdtn.b, E-mail: dallehm@cdtn.b, E-mail: campolina@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    The effective delayed neutron fraction, {beta}{sub eff}, one of the most important parameter in reactor kinetics, was measured for the 100 kW IPR-R1 TRIGA Mark I research reactor, located at the Nuclear Technology Development Center - CDTN, Belo Horizonte, Brazil. The current reactor core has 63 fuel elements, containing about 8.5% and 8% by weight of uranium enriched to 20% in U{sup 235}. The core has cylindrical configuration with an annular graphite reflector. Since the first criticality of the reactor in November 1960, the core configuration and the number of fuel elements have been changed several times. At that time, the reactor power was 30 kW, there were 56 fuel elements in the core, and the {beta}{sub eff} value for the reactor recommended by General Atomic (manufacturer of TRIGA) was 790 pcm. The current {beta}{sub eff} parameter was determined from experimental methods based on inhour equation and on the control rod drops. The estimated values obtained were (774 {+-} 38) pcm and (744 {+-} 20) pcm, respectively. The {beta}{sub eff} was calculated by Monte Carlo transport code MCNP5 and it was obtained 747 pcm. The calculated and measured values are in good agreement, and the relative percentage error is -3.6% for the first case, and 0.4% for the second one. (author)

  7. Study on Reactor Performance of Online Power Monitoring in PUSPATI TRIGA Reactor (RTP)

    International Nuclear Information System (INIS)

    Zareen Khan Abdul Jalil Khan; Ridzuan Abdul Mutalib; Mohd Sabri Minhat

    2014-01-01

    The Reactor TRIGA PUSPATI (RTP) at Malaysia Nuclear Agency is a TRIGA Mark II type reactor and pool type cooled by natural circulation of light water. This paper describe on reactor performance of online power monitoring based on various parameter of reactor such as log power, linear power, period, Fuel and coolant temperature and reactivity parameter with using neutronic and other instrumentation system of reactor. Methodology of online power estimation and monitoring is to evaluate and analysis of reactor power which is important of reactor safety and control. Neutronic instrumentation system will use to estimate power measurement, differential of log and linear power and period during reactor operation .This study also focus on noise fluctuation from fission chamber during reactor operation .This work will present result of online power monitoring from RTP which indicated the safety parameter identification and initiate safety action on crossing the threshold set point trip. Conclude that optimization of online power monitoring will improved the reactor control and safety parameter of reactor during operation. (author)

  8. Enrichment measurement in TRIGA type fuels; Medicion de enriquecimiento en combustibles tipo Triga

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar H, F.; Mazon R, R. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2001-05-15

    The Department of Energy of the United States of North America, through the program 'Idaho Operations Nuclear Spent Fuel Program' of the Idaho National Engineering and Environmental Laboratory (INEEL), in Idaho Falls; Idaho USA, hires to Global Technologies Inc. (GTI) to develop a prototype device of detection enrichment uranium (DEU Detection of Enrichment of Uranium) to determine quantitatively the enrichment in remainder U-235 in a TRIGA fuel element at the end of it useful life. The characteristics of the prototype developed by GTI are the following ones: It allows to carry out no-destructive measurements of TRIGA type fuel. Easily transportable due to that reduced of it size. The determination of the enrichment (in grams of U-235) it is obtained with a precision of 5%. The National Institute of Nuclear Research (ININ), in its facilities of the Nuclear Center of Mexico, it has TRIGA type fuel of high and low enrichment (standard and FLIP) fresh and with burnt, it also has the infrastructure (hot cells, armor-plating of transport, etc) and qualified personnel to carry out the necessary maneuvers to prove the operation of the DEU prototype. For this its would be used standard type fuel elements and FLIP, so much fresh as with certain burnt one. In the case of the fresh fuels the measurement doesn't represent any risk, the fuels before and after the measurement its don't contain a quantity of fission products that its represent a radiological risk in its manipulation; but in the case of the fuels with burnt the handling of the same ones represents an important radiological risk reason why for its manipulation it was used the transport armor-plating and the hot cells. (Author)

  9. Lessons Learnt in the Development of Level 1 PUSPATI TRIGA Reactor Probability Safety Assessment: A Collaboration Project under the Norwegian Extra Budgetary Fund

    International Nuclear Information System (INIS)

    Mazleha Maskin; Tom, P.P.; Ahmad Hassan Sallehudin Mohd Sarif; Faizal Mohamed; Mohd Fazli Zakaria; Muhamad Puad Abu

    2014-01-01

    This article reports about the lessons learnt from the development of level 1 probabilistic safety assessment (PSA) project that was implemented under the IAEA mentoring program for TRIGA MARK II PUSPATI research reactor (RTP). As a project that involved more than 3 organizations, a strategic planning of the management and implementation of individual assignment is truly a hectic task. This report compiles all related activities from the forming of the Malaysian PSA team up to the final report submitted to the IAEA. (author)

  10. Neutronic study of nuclear reactors. Complete calculation of TRIGA MARKII reactor and calculations of fuel temperature coefficients. (Qualification of WIMS code)

    International Nuclear Information System (INIS)

    Benmansour, L.

    1992-01-01

    The present work shows a group of results, obtained by a neutronic study, concerning the TRIGA MARK II reactor and LIGHT WATER reactors. These studies aim to make cell and diffusion calculations. WIMS D-4 with extended library and DIXY programs are used and tested for those purposes. We also have proceeded to a qualification of WIMS code based on the fuel temperature coefficient calculations. 33 refs.; 23 figs.; 30 tabs. (author)

  11. Cephalometric standards for Slovenians in the mixed dentition period.

    Science.gov (United States)

    Drevensek, Martina; Farcnik, Franc; Vidmar, Gaj

    2006-02-01

    The aim of this study was to develop standard cephalometric values for Slovenians in the period of the mixed dentition. Eighty-eight children were included in the study (46 girls and 42 boys, mean age 9.31 +/- 1.52 years). The selection criteria were: in the mixed dentition, a score of the modified Eismann method for an objective assessment of malocclusion of less than 15 points, the absence of aplasia and supernumerary teeth, no congential anomalies and no previous orthodontic treatment. Twenty-five cephalometric measurements were performed twice to analyse the size and shape of the craniofacial complex. The reliability of the measurements was assessed by correlation coefficients, regression, and analysis of inter-subject differences; satisfactory results were obtained. The differences between boys and girls and between those in the early and late mixed dentition period were tested with a two-way analysis of variance. The most pronounced changes between the early and late mixed dentition were observed in the vertical skeletal relationships: a decrease in mandibular inclination, interbasal angle and gonial angle, and an increase in anterior and posterior face height. Sagittal skeletal relationships remained constant from the early to the late mixed dentition. No significant differences were found between the observed developmental stages. Significant differences between genders were found only for anterior and posterior face height, with boys showing larger values (P mixed dentition, the mean measurement values of the total sample can be used as cephalometric standards for Slovenians in the mixed dentition period.

  12. Productivity growth and price regulation of Slovenian water distribution utilities

    Directory of Open Access Journals (Sweden)

    Jelena Zorić

    2010-06-01

    Full Text Available This paper aims to analyse the price regulation method and performance of thewater industry in Slovenia. A stochastic cost frontier model is employed to estimate and decompose the total factor productivity (TFP growth of water distribution utilities in the 1997-2003 period. The main goal is to find out whether the lack of proper incentives to improve performance has resulted in the low TFP growth of Slovenian water distribution utilities. The evidence suggests that cost inefficiencies are present in water utilities, which indicates considerable cost saving potential in the analysed industry. Technical change is found to have positively affected the TFP growth over time, while cost inefficiency levels remained essentially unchanged. Overall, the average annual TFP growth in the analysed period is estimated to be only slightly above zero, which is a relatively poor result. This can largely be contributed to the present institutional and regulatory setting that does not stimulate utilities to improve productivity. Therefore, the introduction of an independent regulatory agency and an incentive-based price regulation scheme should be seriously considered in order to enhance the performance of Slovenian water distribution utilities.

  13. Implementation of the k{sub 0} technique using multi-detectors on diverse irradiation facilities of TRIGA Reactor; Implementacion de la tecnica k{sub 0} usando multidetectores en diferentes instalaciones de irradiacion del Reactor TRIGA

    Energy Technology Data Exchange (ETDEWEB)

    Caldera C, M. de G.

    2013-07-01

    The k{sub 0} method with the technique of neutron activation analysis allows obtaining important characteristics parameters that describe a nuclear reactor. Among these parameters are the form factor of epithermal neutron flux, α and the ratio of thermal neutron flux with respect to the epithermal neutron flux, f. These parameters were obtained by irradiation of two different monitors, one of Au-Zr and the other of Au-Mo-Cr, where the last one was made and implemented for the first time. Both monitors were irradiated in different positions in the TRIGA Mark III Reactor at the National Institute of Nuclear Research. (Author)

  14. Installation, performance, safety aspects and technical data of the triple axis Spectrometer at TRIGA Reactor of AERE

    International Nuclear Information System (INIS)

    Yunus, S. M.; Kamal, I.; Datta, T. K.; Zakaria, A. K. M.; Ahmed, F. U.

    2004-02-01

    The technical data of the Triple Axis Neutro Spectrometer installed at the 3 MW TRIGA Mark II research reactor has been described. These are the reference data required for the operation, maintenance and use of the spectrometer. The detail information of the installation of the spectrometer has been given. Radiation safety features of the spectrometer and around the radial piercing beam port (where the spectrometer is installed) are described elaborately. The quality test experiments and the performance of the spectrometer as found from these tests are also described

  15. Implementation of the k0 technique using multi-detectors on diverse irradiation facilities of TRIGA Reactor

    International Nuclear Information System (INIS)

    Caldera C, M. de G.

    2013-01-01

    The k 0 method with the technique of neutron activation analysis allows obtaining important characteristics parameters that describe a nuclear reactor. Among these parameters are the form factor of epithermal neutron flux, α and the ratio of thermal neutron flux with respect to the epithermal neutron flux, f. These parameters were obtained by irradiation of two different monitors, one of Au-Zr and the other of Au-Mo-Cr, where the last one was made and implemented for the first time. Both monitors were irradiated in different positions in the TRIGA Mark III Reactor at the National Institute of Nuclear Research. (Author)

  16. Status of the TRIGA shipments to the INEEL from Europe

    International Nuclear Information System (INIS)

    Mustin, T.; Stump, R.C.; Tyacke, M.J.

    1997-01-01

    This paper reports the activities underway by the US Department of Energy (DOE) for returning Training, Research, Isotope, General Atomics (TRIGA) spent nuclear fuel (SNF) from foreign research reactors (FRR) in four European countries to the Idaho National Engineering and Environmental Laboratory (INEEL). Those countries are Germany, Italy, Romania, and Slovenia. This is part of the ''Nuclear Weapons Nonproliferation Policy'' of returning research reactor SNF containing uranium enriched in the US. This paper describes the results of a pre-assessment trip in September, 1997, to these countries, including: history of the reactors and research being performed; inventory of TRIGA SNF; fuel types (stainless steel, aluminum, or Incoloy) and enrichments; and each country's plans for returning their TRIGA SNF to the INEEL

  17. Status of the TRIGA user facility in Mainz

    Energy Technology Data Exchange (ETDEWEB)

    Kories, Fabian; Heil, Werner; Karch, Jan Peter; Sobolev, Yury [Institut fuer Physik, Johannes Gutenberg Universitaet Mainz (Germany); Eberhardt, Klaus; Hampel, Gabriele; Reich, Tobias; Trautmann, Norbert [Institut fuer Kernchemie, Johannes Gutenberg Universitaet Mainz (Germany)

    2014-07-01

    Ultra-cold neutrons (UCN) offer unique opportunities for investigating the properties of the free neutron with exceptionally high precision such as the measurement of its lifetime. At the pulsed TRIGA reactor in Mainz, a superthermal UCN source using solid deuterium as converter is operational and delivers up to 10 UCN/cm{sup 3} in typical storage volumes of 10 l. Within PRISMA Cluster of excellence, this source will be upgraded to a targeted strength of 100 UCN/cm{sup 3} in order to transform TRIGA Mainz into a world-leading user facility for UCN research. Besides the installation of a He liquefier to sustain long-term experiments, the existing neutron guides have to be replaced by high-quality guides with low surface roughness which are internally coated with Ni-58 to increase the phase space for UCN transport. The poster gives a status report on the activities at the UCN source at TRIGA Mainz.

  18. TRIGA criticality experiment for testing burn-up calculations

    International Nuclear Information System (INIS)

    Persic, Andreja; Ravnik, Matjaz; Zagar, Tomaz

    1999-01-01

    A criticality experiment with partly burned TRIGA fuel is described. 20 wt % enriched standard TRIGA fuel elements initially containing 12 wt % U are used. Their average burn-up is 1.4 MWd. Fuel element burn-up is calculated in 2-D four group diffusion approximation using TRIGLAV code. The burn-up of several fuel elements is also measured by reactivity method. The excess reactivity of several critical and subcritical core configurations is measured. Two core configurations contain the same fuel elements in the same arrangement as were used in the fresh TRIGA fuel criticality experiment performed in 1991. The results of the experiment may be applied for testing the computer codes used for fuel burn-up calculations. (author)

  19. History, Development and Future of TRIGA Research Reactors. Companion CD-ROM

    International Nuclear Information System (INIS)

    2016-01-01

    Due to its particular fuel design and resulting enhanced inherent safety features, TRIGA reactors (Training, Research, Isotopes, General Atomics) constitute a ‘class of their own’ among the large variety of research reactors built world-wide. This publication summarizes in a single document the information on the past and present of TRIGA research reactors and presents an outlook in view of potential issues to be solved by TRIGA operating organizations in the near future. It covers the historical development and basic TRIGA characteristics, followed by utilization, fuel conversion and ageing management of TRIGA research reactors. It continues with issues and challenges, introduction to the global TRIGA research reactor network and concludes with future perspectives. This CD-ROM illustrates the historical developments of TRIGA research reactors through individual facility examples and experiences

  20. TRIGA 14 MW Research Reactor Status and Utilization

    International Nuclear Information System (INIS)

    Barbos, D.; Ciocanescu, M.; Paunoiu, C.

    2016-01-01

    Institute for Nuclear Research is the owner of the largest family TRIGA research reactor, TRIGA14 MW research reactor. TRIGA14 MW reactor was designed to be operated with HEU nuclear fuel but now the reactor core was fully converted to LEU nuclear fuel. The full conversion of the core was a necessary step to ensure the continuous operation of the reactor. The core conversion took place gradually, using fuel manufactured in different batches by two qualified suppliers based on the same well qualified technology for TRIGA fuel, including some variability which might lead to a peculiar behaviour under specific conditions of reactor utilization. After the completion of the conversion a modernization program for the reactor systems was initiated in order to achieve two main objectives: safe operation of the reactor and reactor utilization in a competitive environment to satisfy the current and future demands and requirements. The 14 MW TRIGA research reactor operated by the Institute for Nuclear Research in Pitesti, Romania, is a relatively new reactor, commissioned 37 years ago. It is expected to operate for another 15-20 years, sustaining new fuel and testing of materials for future generations of power reactors, supporting radioisotopes production through the development of more efficient new technologies, sustaining research or enhanced safety, extended burn up and verification of new developments concerning nuclear power plants life extension, to sustain neutron application in physics research, thus becoming a centre for instruction and training in the near future. A main objective of the TRIGA14MW research reactor is the testing of nuclear fuel and nuclear material. The TRIGA 14 MW reactor is used for medical and industrial radioisotopes production ( 131 I, 125 I, 192 Ir etc.) and a method for 99 Mo- 99 Tc production from fission is under development. For nuclear materials properties investigation, neutron radiography methods have been developed in the INR. The

  1. Environmental radiation monitoring from the decommission of TRIGA

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Geun Sik; Lee, Chang Woo

    2000-03-01

    Environmental radiation monitoring was carried out with measurement of environmental radiation and environmental radioactivity analysis around TRIGA Research Reactor. The results of environmental radiation monitoring around TRIGA Research Reactor are the follows: The average level of environmental radiation measured by potable ERM and accumulated radiation dose by TLD was almost same level compared with thepast years. Gross {beta} radioactivity in environmental samples showed a environmental level. {gamma}-radionuclides in water samples were not detected. but only radionuclide K-40, which is natural radionuclide, was detected in the all samples and Cs-137 was detected in the surface soil and discharge sediment. (author)

  2. Prototypic fabrication of TRIGA irradiated fuel shipping casks

    International Nuclear Information System (INIS)

    Kim, B.K.; Lee, Y.W.; Whang, C.K.; Lee, J.B.

    1980-01-01

    This is the safety analysis report on the prototypic fabrication of ''TRIGA Irradiated Fuel Shipping Cask'' conducted by KAERI in 1980. The results of the evaluation show that the shipping cask is in compliance with the applicable regulation for the normal conditions of transport as well as hypothetical accident conditions. The prototypic fabrication of the shipping cask (type B) was carried out for the first time in Korea after getting technical experience from fabrication of the ''TRIGA Spent Fuel Shipping Cask'' and ''the KO-RI Unit 1 surveillance capsule shipping cask'' in 1979. This report contains structural evaluation, thermal evaluation, shielding, criticality, quality assurance, and handling procedures of the shipping cask

  3. Testing of cross section libraries for TRIGA criticality benchmark

    International Nuclear Information System (INIS)

    Snoj, L.; Trkov, A.; Ravnik, M.

    2007-01-01

    Influence of various up-to-date cross section libraries on the multiplication factor of TRIGA benchmark as well as the influence of fuel composition on the multiplication factor of the system composed of various types of TRIGA fuel elements was investigated. It was observed that keff calculated by using the ENDF/B VII cross section library is systematically higher than using the ENDF/B-VI cross section library. The main contributions (∼ 2 20 pcm) are from 235 U and Zr. (author)

  4. Environmental radiation monitoring from the decommission of TRIGA

    Energy Technology Data Exchange (ETDEWEB)

    Choi Geun Sik; Lee, Chang Woo [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-02-01

    Environmental Radiation Monitoring was carried out with measurement of environment radiation and environment radioactivity analysis around TRIGA Research Reactor. The results of environmental radiation monitoring around TRIGA Research Reactor are the follows: The average level of environmental radiation dose measured by potable ERM and accumulated radiation dose by TLD was almost same level compared with the past years. Gross {beta} radioactivity in environmental samples showed a environmental level. v-radionuclides in water samples were not detected. But only radionuclide K-40, which is natural radionuclide, was detected in the all samples and Cs-137 was detected in the surface soil and discharge sediment. 37 refs., 12 figs., 31 tabs. (Author)

  5. Operation and reactivity measurements of an accelerator driven subcritical TRIGA reactor

    Science.gov (United States)

    O'Kelly, David Sean

    Experiments were performed at the Nuclear Engineering Teaching Laboratory (NETL) in 2005 and 2006 in which a 20 MeV linear electron accelerator operating as a photoneutron source was coupled to the TRIGA (Training, Research, Isotope production, General Atomics) Mark II research reactor at the University of Texas at Austin (UT) to simulate the operation and characteristics of a full-scale accelerator driven subcritical system (ADSS). The experimental program provided a relatively low-cost substitute for the higher power and complexity of internationally proposed systems utilizing proton accelerators and spallation neutron sources for an advanced ADSS that may be used for the burning of high-level radioactive waste. Various instrumentation methods that permitted ADSS neutron flux monitoring in high gamma radiation fields were successfully explored and the data was used to evaluate the Stochastic Pulsed Feynman method for reactivity monitoring.

  6. Basic research using the 250 KW research reactor triga in Ljubljana, Yugoslavia

    International Nuclear Information System (INIS)

    Dimic, V.

    1983-01-01

    The 25 KW Triga Mark II reactor of J. 'Stefan Institute' was commissioned on May 1966. During the last two years, it has been operated for about 4200 hr/year. According to experience gained with the reactor, most of the cost of reactor operation will be earned through isotope production for local hospitals and industries, performing low cost applied experiments and organizing training courses. The rest was provided through the Research Communities of the Republic of Slovenia. The reactor has been operated for 15 years without major problems and many basic research programmes have been performed. The research is being conducted in the following mainfields: solid state physics, neutron dosimetry, neutron radiography and autoradiography, reactor physics, examination of nuclear fuel using gamma scanning, irradiation of semiconducting materials and neutron activation analysis. (A.J)

  7. Irradiation facility at the TRIGA Mainz for treatment of liver metastases

    Energy Technology Data Exchange (ETDEWEB)

    Hampel, G. [Institut fuer Kernchemie, Johannes Gutenberg-Universitaet Mainz, Fritz-Strassmann-Weg 2, D-55128 Mainz (Germany)], E-mail: gabriele.hample@uni-mainz.de; Wortmann, B. [Evonik Energy Services GmbH Essen, Ruettenscheider Str. 1-3, D-45128 Essen (Germany); Blaickner, M. [Austrian Research Centers, 2444 Seibersdorf (Austria); Knorr, J. [TU Dresden, Institut fuer Energietechnik, D-01062 Dresden (Germany); Kratz, J.V. [Institut fuer Kernchemie, Johannes Gutenberg-Universitaet Mainz, Fritz-Strassmann-Weg 2, D-55128 Mainz (Germany); Lizon Aguilar, A. [Evonik Energy Services GmbH Essen, Ruettenscheider Str. 1-3, D-45128 Essen (Germany); Minouchehr, S. [Transplantationschirurgie, Universitaetsklinikum Mainz, D-55131 Mainz (Germany); Nagels, S. [Forschungszentrum Karlsruhe GmbH, Institut fuer Strahlenforschung (ISF), Postfach 3640, D-76021 Karlsruhe (Germany); Otto, G. [Transplantationschirurgie, Universitaetsklinikum Mainz, D-55131 Mainz (Germany); Schmidberger, H. [Klinik und Poliklinik fuer Radioonkologie und Strahlentherapie, Universitaetsklinikum Mainz, D-55131 Mainz (Germany); Schuetz, C.; Vogtlaender, L. [Institut fuer Kernchemie, Johannes Gutenberg-Universitaet Mainz, Fritz-Strassmann-Weg 2, D-55128 Mainz (Germany)

    2009-07-15

    The TRIGA Mark II reactor at University of Mainz provides ideal conditions for duplicating BNCT treatment as performed in Pavia, Italy, in 2001 and 2003 [Pinelli, T., Zonta, A., Altieri, S., Barni, S., Braghieri, A., Pedroni, P., Bruschi, P., Chiari, P., Ferrari, C., Fossati, F., Nano, R., Ngnitejeu Tata, S., Prati, U., Ricevuti, G., Roveda, L., Zonta, C., 2002. TAOrMINA: from the first idea to the application to the human liver. In: Sauerwein et al. (Eds.), Research and Development in Neutron Capture Therapy. Proceedings of the 10th International Congress on Neutron Capture Therapy, Monduzzi editore, Bologna, pp. 1065-1072]. In order to determine the optimal parameters for the planned therapy and therefore for the design of the thermal column, calculations were conducted using the MCNP-code and the transport code ATTILA. The results of the parameter study as well as a possible configuration for the irradiation of the liver are presented.

  8. Verification of MCNP simulation of neutron flux parameters at TRIGA MK II reactor of Malaysia.

    Science.gov (United States)

    Yavar, A R; Khalafi, H; Kasesaz, Y; Sarmani, S; Yahaya, R; Wood, A K; Khoo, K S

    2012-10-01

    A 3-D model for 1 MW TRIGA Mark II research reactor was simulated. Neutron flux parameters were calculated using MCNP-4C code and were compared with experimental results obtained by k(0)-INAA and absolute method. The average values of φ(th),φ(epi), and φ(fast) by MCNP code were (2.19±0.03)×10(12) cm(-2)s(-1), (1.26±0.02)×10(11) cm(-2)s(-1) and (3.33±0.02)×10(10) cm(-2)s(-1), respectively. These average values were consistent with the experimental results obtained by k(0)-INAA. The findings show a good agreement between MCNP code results and experimental results. Copyright © 2012 Elsevier Ltd. All rights reserved.

  9. Seven years of operation of the U. S. geological survey TRIGA reactor

    International Nuclear Information System (INIS)

    Kraker, Pat

    1976-01-01

    February 1976 marks 7 years of operation of the U. S. Geological Survey TRIGA Reactor (GSTR) facility. In these 7 years we have generated more than 5800 MWH's of thermal energy and irradiated more than 47,000 samples for experimenters from the Survey, universities, and other Governmental agencies. Several mechanical and electrical components have required attention. Changes to the technical specifications have included one minor wording change involving the evacuation alarm, a reevaluation of the measurement of argon-41 concentrations, a revision concerning transient-rod maintenance, and a reduction in the frequency of fuel-element measurements. To improve physical security we have increased building security, installed an intrusion alarm, and, most recently, expanded the boundaries of the facility within the building to provide better control access. There also have been major changes to our operating procedures and the initiation of a reactor-operator requalification program. (author)

  10. Prayer marks.

    Science.gov (United States)

    Abanmi, Abdullah A; Al Zouman, Abdulrahman Y; Al Hussaini, Husa; Al-Asmari, Abdulrahman

    2002-07-01

    Prayer marks (PMs) are asymptomatic, chronic skin changes that consist mainly of thickening, lichenification, and hyperpigmentation, and develop over a long period of time as a consequence of repeated, extended pressure on bony prominences during prayer. Three hundred and forty-nine Muslims and 24 non-Muslims were examined for the appearance of PMs at different body sites. The prospective study of 349 Muslims (both males and females) with regular praying habits showed the occurrence of PMs on specific locations, such as the forehead, knees, ankles, and dorsa of the feet, leading to dermatologic changes consisting of lichenification and hyperpigmentation. The incidence of PMs was significantly higher in males than in females. Older subjects (over 50 years of age) demonstrated a significantly higher frequency of lichenification and hyperpigmentation, suggesting that repeated pressure and friction for prolonged periods are the causative factors for the development of PMs. Histologic examination of skin biopsies from the affected sites showed compact orthokeratosis, hypergranulosis, dermal papillary fibrosis, and dermal vascularization. PMs were not associated with any risk of secondary complications, such as erythema, bullous formation, and infections. PMs are commonly occurring dermatologic changes in Muslims who pray for prolonged periods.

  11. Tržna podoba slovenskih gazel = Market Branding of Slovenian Gazelles

    Directory of Open Access Journals (Sweden)

    Gabrijel Devetak

    2012-01-01

    Full Text Available The purpose of the article is to show the global marketing activities,guidelines and management decisions for international business ofSlovenian gazelles. The survey was conducted on a sample of 230-sSlovenian gazelles that have been included in the list of 500 fastestgrowing companies in Slovenia in previous years (2007, 2008, 2009 and2010. They are also involved in the selection of ‘Best Fast GrowingCompany or a Gazelle.’ Slovenian gazelles use the internationalizationfor many reasons (saturation of the domestic market, lack of demandin the domestic market, etc.. Findings presented in this articlemay serve Slovenian gazelle in the decision of how to enter a foreignmarket, in the selection of the initial steps and the comparison of the existing market models used in the company.

  12. The use of derivatives in Slovenian non-financial firms: is financial risk already well managed?

    Directory of Open Access Journals (Sweden)

    Aleš Berk

    2006-12-01

    Full Text Available Recent research about the financial behaviour of Slovenian firms has documented enterprise risk management as being one of its weakest areas. The goal of this article is to present insights into financial risk management, i.e. into the extent of the use of derivatives in the largest Slovenian firms and the related practices. The resultsare confronted with the same types of characteristics of US and German firms (although being much larger revealed in comparable studies. These firms provide relevant benchmarks for assessing the development gap since they operate in more advanced financial environments and are therefore expected to have much morerefined approaches to the use of derivatives than Slovenian firms. A survey points to the much smaller extent of the use of derivatives by Slovenian firms. There is a substantial gap, especially in the area of risk management policies (e.g. documentation, reporting, counterparty risk, valuation etc..

  13. Hydraulic conductivities of fractures and matrix in Slovenian carbonate aquifers

    Directory of Open Access Journals (Sweden)

    Timotej Verbovšek

    2008-12-01

    Full Text Available Hydraulic conductivities and specific storage coefficients of fractures and matrix in Slovenian carbonate aquifers were determined by Barker’s method for pumping test analysis, based on fractional flow dimension. Values are presented for limestones and mainly for dolomites, and additionally for separate aquifers, divided by age andlithology in several groups. Data was obtained from hydrogeological reports for 397 water wells, and among these, 79 pumping tests were reinterpreted. Hydraulic conductivities of fractures are higher than the hydraulic conductivities of matrix, and the differences are highly statistically significant. Likewise, differences are significant for specific storage, and the values of these coefficients are higher in the matrix. Values of all coefficients vary in separate aquifers, and the differences can be explained by diagenetic effects, crystal size, degree of fracturing, andcarbonate purity. Comparison of the methods, used in the reports, and the Barker’s method (being more suitable for karstic and fractured aquifers, shows that the latter fits real data better.

  14. "Othering" agricultural biotechnology: Slovenian media representation of agricultural biotechnology.

    Science.gov (United States)

    Zajc, Jožica; Erjavec, Karmen

    2014-08-01

    While studies on media representations of agricultural biotechnology mostly analyse media texts, this work is intended to fill a research gap with an analysis of journalistic interpretations of media representations. The purpose of this project was to determine how news media represent agricultural biotechnology and how journalists interpret their own representations. A content and critical discourse analysis of news texts published in the Slovenian media over two years and in-depth interviews with their authors were conducted. News texts results suggest that most of the news posts were "othering" biotechnology and biotechnologists: biotechnology as a science and individual scientists are represented as "they," who are socially irresponsible, ignorant, arrogant, and "our" enemies who produce unnatural processes and work for biotechnology companies, whose greed is destroying people, animals, and the environment. Most journalists consider these representations to be objective because they have published the biotechnologists' opinions, despite their own negative attitudes towards biotechnology.

  15. Slovenian national health insurance card: the next step.

    Science.gov (United States)

    Kalin, T; Kandus, G; Trcek, D; Zupan, B

    1999-01-01

    The Slovenian national health insurance company started a full-scale deployment of the insurance smart card that is at the present used for insurance data and identification purpose only. There is ample capacity on the cards that were selected, to contain much more data than needed for the purely administrative and charging purposes. There are plans to include some basic medical information, donor information, etc. On the other hand, there are no firm plans to use the security infrastructure and the extensive network, connecting the insurance company with the more than 200 self service terminals positioned at the medical facilities through the country to build an integrated medical information system that would be very beneficial to the patients and the medical community. This paper is proposing some possible future developments and further discusses on the security issues involved with such countrywide medical information system.

  16. Better Regulation and Public Procurement in Slovenian Municipalities

    Directory of Open Access Journals (Sweden)

    Maja KLUN

    2013-02-01

    Full Text Available The reduction of administrative burdens is a measure to improve regulatory quality. Most measures are directed towards reducing barriers for business while the issue of regulation inside government is not often posed. The research carried out in 2010 was intended to investigate how Slovenian municipalities and others in the public sector perceive measures to reduce administrative burdens and the areas in which they consider regulations to present the greatest burden. Results have shown that public procurement regulations are the greatest burden for municipalities and the public sector as a whole. Further research indicates which public procurement procedures municipalities used most often and what benefits they perceive in the amended legislation. Results indicate that most municipalities use open procedures most often, which procedurally is the most complex.

  17. Social policies related to parenthood and capabilities of Slovenian parents.

    Science.gov (United States)

    Mrčela, Aleksandra Kanjuo; Sadar, Nevenka Černigoj

    2011-01-01

    We apply Sen's capability approach to evaluate the capabilities of Slovenian parents to reconcile paid work and family in the context of the transition to a market economy. We examine how different levels of capabilities together affect the work–life balance (WLB) of employed parents. We combine both quantitative and qualitative methodological approaches. The results of our quantitative and qualitative research show that increased precariousness of employment and intensification of work create gaps between the legal and normative possibilities for successful reconciliation strategies and actual use of such arrangements in Slovenia. The existing social policies and the acceptance of gender equality in the sphere of paid work enhance capabilities for reconciliation of paid work and parenthood, whereas the intensification of working lives, the dominance of paid work over other parts of life, and the acceptance of gender inequalities in parental and household responsibilities limit parents’ capabilities to achieve WLB.

  18. AN EMPIRICAL STUDY OF MARKETING COMMUNICATIONS EFFECTIVENESS IN SLOVENIAN MARKET

    Directory of Open Access Journals (Sweden)

    Damjana Jerman

    2014-01-01

    Full Text Available This paper deals with the value or more specifically, the contribution of marketing communications strategy to effectiveness of marketing communications and hypothesizes that marketing communications strategy correlate with the effectiveness of marketing communications. The paper consists of two parts: the theoretical framework for the role of marketing communications strategy for the effectiveness of the marketing communications and the empirical analysis, based on the primary data collected. The concept of the marketing communication effectiveness assumes that there are variables that can have a positive influence on the effectiveness of marketing communications, which incorporates facets of the marketing communication strategy and bidirectional communications. The results suggest that Slovenian organisations which design and implement marketing communication strategy, also have more effective marketing communications. The development of marketing communications strategy was correlated with increased effectiveness of marketing communications in their organisation. Managerial implications are discussed along with directions for further research.

  19. Job satisfaction of nurses and identifying factors of job satisfaction in Slovenian Hospitals

    OpenAIRE

    Lorber, Mateja; Skela Savič, Brigita

    2012-01-01

    Aim To determine the level of job satisfaction of nursing professionals in Slovenian hospitals and factors influencing job satisfaction in nursing. Methods The study included 4 hospitals selected from the hospital list comprising 26 hospitals in Slovenia. The employees of these hospitals represent 29.8% and 509 employees included in the study represent 6% of all employees in nursing in Slovenian hospitals. One structured survey questionnaire was administered to the lea...

  20. Agile metodologies use for software development in Slovenian start-ups

    OpenAIRE

    Kašnik, Matic

    2014-01-01

    The thesis presents and describes the use of agile methodologies which are being used by Slovenian tech start-up companies. It describes the basic features, advantages and disadvantages of various agile methodologies such as Scrum, extreme programming, lean start-up and method Kanban. We made a review of the most used agile methodologies in Slovenian technology start-up companies. In particular, we focus on variety of tools, technics and approaches used by the development teams and where do t...

  1. Intellectual capital in the Slovenian hotel industry before and after entry into the EU

    OpenAIRE

    Nemec Rudež, Helena

    2007-01-01

    The intellectual capital in the Slovenian hotel industry has been improved in the past few years what is extremely desirable and necessary since today the Slovenian hotel industry is facing increased competition in the enlarged European single market. The paper presents an empirical analysis of the development of intellectual capital in the hotel industry in Slovenia between 2003 and 2006. In this period of time Slovenia entered the European Union (EU). The results show progress of intellectu...

  2. Slovenian Secondary School Visual Arts Curriculum in Comparison with Similar European Documents

    Directory of Open Access Journals (Sweden)

    Tomaž Zupančič

    2015-12-01

    Full Text Available Political changes in Slovenia in the early 1990s were followed by changes to the educational system. As regards the professional field, the last thirty years have seen major changes to teaching art all around the globe and also in Slovenia in the sense of the so-called postmodern visual arts curriculum. Slovenian art curricula are facing similar problems as the curricula in other countries. By comparing Slovenian art curricula for secondary school with those in seven different countries (Croatia, Estonia, Finland, Ireland, Latvia, Norway, and Spain, we wished to shed light on the Slovenian curriculum in a broader context. The Slovenian curriculum and those of other countries have been scrutinised and juxtaposed from different viewpoints. It has been established that Slovenian course syllabi have individual characteristics in common with the countries compared. The placement of art education into the timetable is similar to that in other countries. In Slovenia and in all the other countries, art education is a compulsory subject but with a different amount of taught time. The documents show differences as regards their structure, the terminology in the classification of the fields of visual arts, the implementation of contemporary content, multiculturalism, and sustainability. The comparison has shown that the Slovenian national curriculum for gimnazija has a modern design in specific segments, while it could be better in others.

  3. Managerial ownership and corporate performance in Slovenian post-privatisation period

    Directory of Open Access Journals (Sweden)

    Marko Simoneti

    2004-12-01

    Full Text Available The Slovenian post-privatisation period has been characterised by a decline in the ownership by non-managerial owners (employees and state-controlled funds. On the other hand, domestic and foreign non-financial firms, Privatisation Investment Funds and managers have been increasing their holdings. The latter, namely the growing managerial ownership, is likely to feature in future ownership dynamics in Slovenia. In fact, in 2002 the desired (optimal ownership stakes estimated by Slovenian managers were 10.8 percentage points higher than their actual stakes. The aim of our paper is to describe the main trends in the ownership of Slovenian corporations in the post-privatisation period and to provide an answer to the basic economic question: what is the influence of the ongoing consolidation of managerial ownership on the performance of Slovenian firms. The empirical analysis testing this relationship is based on a panel of 182 Slovenian firms in the 1995-99 period and does not provide relevant evidence of any positive effects of the increasing managerial control on Slovenian firms’ performance. If any, a positive incentive effect is only observed in those firms whose managers’ holdings exceed 10-percent, only with regards to firms’ financial performance (but not total factor productivity and only in firms that are not listed on the capital market. Further, the negative effect of the current gap between the desired and actual managerial ownership seems to exceed any positive incentive effect arising out of managerial ownership

  4. Cross-disciplinary research programs at the Cornell TRIGA reactor

    International Nuclear Information System (INIS)

    Clark, D.D.

    1995-01-01

    This paper describes cross-disciplinary research efforts at the Cornell TRIGA reactor. A new graduate laboratory course for nonspecialists was developed which brought in graduate students from many fields, and a weekly or bimonthly nuclear methods seminars are being held to describe research methods, sample preparation, irradiation, etc

  5. Irradiation routine in the IPR-R1 Triga reactor

    International Nuclear Information System (INIS)

    Maretti Junior, F.

    1980-01-01

    Information about irradiations in the IPR-R1 TRIGA reactor and procedures necessary for radioisotope solicitation are presented All procedures necessary for asking irradiation in the reactor, shielding types, norms of terrestrial and aerial expeditions, payment conditions, and catalogue of disposable isotopes with their respective saturation activities are described. (M.C.K.)

  6. Current research work at the TRIGA reactor in Ljubljana

    International Nuclear Information System (INIS)

    Najzer, M.; Dimic, V.

    1978-01-01

    The research programmes at this TRIGA reactor cover quite broad and different research fields. They can be grouped in the following topics: reactor dynamics and operation, neutron activation analysis, solid state physics research, reactor dosimetry, radiography and fuel burn-up determination. In this presentation a short overview is given of those investigations which are not described in detail in separate papers

  7. ORIGEN2 calculations supporting TRIGA irradiated fuel data package

    Energy Technology Data Exchange (ETDEWEB)

    Schmittroth, F.A.

    1996-09-20

    ORIGEN2 calculations were performed for TRIGA spent fuel elements from the Hanford Neutron Radiography Facility. The calculations support storage and disposal and results include mass, activity,and decay heat. Comparisons with underwater dose-rate measurements were used to confirm and adjust the calculations.

  8. Specimen rotation system of the WSU TRIGA-fueled reactor

    International Nuclear Information System (INIS)

    Lovas, Thomas A.

    1976-01-01

    The specimen rotation system presently in use at the WSU reactor has been designed to provide maximum utilization of the irradiation capabilities achieved through use of TRIGA-type fuel. This paper describes the system with particular emphasis on characteristics which are advantageous to experimenters. (author)

  9. 3. European conference of TRIGA users. Papers and abstracts

    International Nuclear Information System (INIS)

    1974-01-01

    The Third European Conference of TRIGA Users was held October 29-31, 1974, in Neuherberg near Munich, Germany under the sponsorship of the Gesellschaft fur Strahlen and Umweltforschung mbH, Physikalischen-Technische Ableilung. The main topics were: experience in reactor operation, maintenance, measurements, fuel management and fuel performance, neutron physical experiments and other research programs

  10. The TRIGA in virtual classroom for training; El TRIGA en aula virtual para entrenamiento

    Energy Technology Data Exchange (ETDEWEB)

    Plata M, A. C.; Morales S, J. B.; Salazar S, E. [UNAM, DEPFI Campus Morelos, Jiutepec Morelos 62550 (Mexico)]. e-mail: yoyuclof@hotmail.com

    2008-07-01

    The research nuclear reactors have been fundamental part in the evolution of the nuclear power plants and they have been used in the training for the obtaining of operation licenses of radioactive facilities. For purposes of training of professionals in nuclear engineering, it is interesting to know the benefit that can be obtained by means of the virtual representation of a research nuclear reactor TRIGA, with which they are possible the practice to be realized them but common that to date they are carried out in different nuclear facilities of training throughout the world. The simulation has become a valuable tool in the personal preparation, having obtained ambient and very approximate situations to the reality. The physical models of kinetics of neutrons, heat transfer, Cherenkov effect, dynamics of the xenon, as well as the virtual instrumentation is contemplated in this development. The instrumentation and control panels of a research reactor, failures waited for in the use of this equipment, physical consequences to instruments, virtual personnel and facilities, as well as the administrative and legal aspects that it requires to meet an authorized operator, must be available and they are considered in the first virtual approach. The obtaining of the reactor time constant comprises of the mathematical model that provides to the operator of a direct way the knowledge of the changes of power. The coolant and moderator are modeled as well as the retardations that appear in the measurements and controls that can be introduced from the virtual console. In the simulator the four possible states of operation of the TRIGA can be had. At the moment also the monitoring can be realized and control in remote form, thus the control and supervision interface for the remote operation will be analyzed in their benefits and possible risks in the instruction processes. (Author)

  11. Implementation of the Finnish Triga reactor and short lived isotopes for diagnostic and irradiation services. Otaniemen Triga-reaktorin ja sillae tuotettujen radioisotooppien saeteilytekniset sovellutukset

    Energy Technology Data Exchange (ETDEWEB)

    Hiismaeki, P.

    1992-01-01

    The spectrum of radiation diagnostic methods and irradiation services, already implemented or under development at the Finnish Triga laboratory is discussed. Most attention is devoted to the boron neutron capture therapy project, which has lead to a very encouraging assessment of this modality at the Triga. (orig.).

  12. TRIGA 14 MW spent fuel shipment to USA

    International Nuclear Information System (INIS)

    Toma, C.; Barbos, D.; Preda, M.; Covaci, St.; Ciocanescu, M.

    2008-01-01

    Romania has begun to convert Pitesti TRIGA 14 MW reactor having HEU fuel in its first loading and has agreed to complete conversion of the reactor to LEU fuel by May 12, 2006. Thus it became possible to benefit of US policy as set forth in the Record of Decision (ROD) issued by the Department of Energy (DOE ) on May 13 , 1996 directed for acceptance, management and disposition of the Authorized Material which has been discharged from the foreign research reactors. Consequently, United States, DOE Idaho Operations Office and Institute for Nuclear Research at Pitesti, Romania have mutually agreed the terms and conditions set forth in a contract applicable to the receipt of the Authorized Material. Irradiated and spent nuclear fuel rods from TRIGA reactor containing uranium enriched in the United States that have met the requirements set forth in the Environmental Impact Statement and the ROD have been designated as 'Authorized Material' and transferred to Idaho National Engineering and Environmental Laboratory (INEEL)- USA during the summer of 1999 in a joint shipment. 267 TRIGA spent fuel rods loaded in a Legal Weight Truck Shipping Cask belonging to the NAC International have been transported through an overland truck route from Pitesti, Romania to Koper, Slovenia and from there it was shipped to USA. The paper has the following contents: 1.Introduction; 2.Fuel rods selection; 3.Fuel rods characterization; 4.Evaluation of TRIGA fuel in wet storage; 5.Fuel rods transfer from TRIGA pool to the transport cask; 6.Supporting documentation for transfer approval; 7. Conclusions. In conclusion one is stressed that, on site fuel evaluation process evidenced the existence of very good running and storage conditions in reactor pool during reactor operation and fuel storage. Only one fuel rod had to be packaged prior to placement in the shipping cask because of damaged cladding during negligent handling

  13. Sedimentary record of subsidence pulse at the Triassic/Jurassic boundary interval in the Slovenian Basin (eastern Southern Alps

    Directory of Open Access Journals (Sweden)

    Rožič Boštjan

    2017-08-01

    Full Text Available In the Alpine Realm the Early Jurassic is characterized by the disintegration and partial drowning of vast platform areas. In the eastern part of the Southern Alps (present-day NW Slovenia, the Julian Carbonate Platform and the adjacent, E-W extending Slovenian Basin underwent partial disintegration, drowning and deepening from the Pliensbachian on, whereas only nominal environmental changes developed on the large Dinaric (Friuli, Adriatic Carbonate Platform to the south (structurally part of the Dinarides. These events, however, were preceded by an earlier - and as yet undocumented extensional event - that took place near the Triassic/Jurassic boundary. This paper provides evidence of an accelerated subsidence from four selected areas within the Slovenian Basin, which show a trend of eastwardly-decreasing deformation. In the westernmost (Mrzli vrh section - the Upper Triassic platform-margin - massive dolomite is overlain by the earliest Jurassic toe-of-slope carbonate resediments and further, by basin-plain micritic limestone. Further east (Perbla and Liščak sections the Triassic-Jurassic transition interval is marked by an increase in resedimented carbonates. We relate this to the increasing inclination and segmentation of the slope and adjacent basin floor. The easternmost (Mt. Porezen area shows a rather monotonous, latest Triassic-Early Jurassic basinal sedimentation. However, changes in the thickness of the Hettangian-Pliensbachian Krikov Formation point to a tilting of tectonic blocks within the basin area. Lateral facies changes at the base of the formation indicate that the tilting occurred at and/or shortly after the Triassic/Jurassic boundary

  14. Sedimentary record of subsidence pulse at the Triassic/Jurassic boundary interval in the Slovenian Basin (eastern Southern Alps)

    Science.gov (United States)

    Rožič, Boštjan; Jurkovšek, Tea Kolar; Rožič, Petra Žvab; Gale, Luka

    2017-08-01

    In the Alpine Realm the Early Jurassic is characterized by the disintegration and partial drowning of vast platform areas. In the eastern part of the Southern Alps (present-day NW Slovenia), the Julian Carbonate Platform and the adjacent, E-W extending Slovenian Basin underwent partial disintegration, drowning and deepening from the Pliensbachian on, whereas only nominal environmental changes developed on the large Dinaric (Friuli, Adriatic) Carbonate Platform to the south (structurally part of the Dinarides). These events, however, were preceded by an earlier - and as yet undocumented extensional event - that took place near the Triassic/Jurassic boundary. This paper provides evidence of an accelerated subsidence from four selected areas within the Slovenian Basin, which show a trend of eastwardly-decreasing deformation. In the westernmost (Mrzli vrh) section - the Upper Triassic platform-margin - massive dolomite is overlain by the earliest Jurassic toe-of-slope carbonate resediments and further, by basin-plain micritic limestone. Further east (Perbla and Liščak sections) the Triassic-Jurassic transition interval is marked by an increase in resedimented carbonates. We relate this to the increasing inclination and segmentation of the slope and adjacent basin floor. The easternmost (Mt. Porezen) area shows a rather monotonous, latest Triassic-Early Jurassic basinal sedimentation. However, changes in the thickness of the Hettangian-Pliensbachian Krikov Formation point to a tilting of tectonic blocks within the basin area. Lateral facies changes at the base of the formation indicate that the tilting occurred at and/or shortly after the Triassic/Jurassic boundary

  15. Dynamics model for real time diagnostics of Triga RC-1 system

    International Nuclear Information System (INIS)

    Gadomski, A.M.; Nanni, V.; Meo, G.

    1988-01-01

    This paper presents dynamics model of TRIGA RC-1 reactor system. The model is dedicated to the real-time early fault detection during a reactor operation in one week exploitation cycle. The algorithms are specially suited for real-time, long time and also accelerated simulations with assumed diagnostic oriented accuracy. The approximations, modular structure, numerical methods and validation are discussed. The elaborated model will be build in the TRIGA Supervisor System and TRIGA Diagnostic Simulator

  16. ENEA TRIGA RC-1 reactor activities in the fields of nuclear medicine and neutron radiography

    International Nuclear Information System (INIS)

    Chiesa, Gianni; Festinesi, Armando; Palomba, Mario; Rosa, Roberto; Rossi, Gabriela; Sangiovanni, Gino; Santoro, Emilio; Sedda, Antioco Franco; Storelli, Lucio

    2008-01-01

    In the last three years, TRIGA RC-1 plant staff is involved in collaborations with some roman hospitals for the production of particular radioisotopes for the diagnosis and therapy in the field of human cancer. Further, the thermal column of TRIGA reactor has been prepared for neutron radiography and tomography. For another channel, instruments and equipment above neutron radiography and tomography are in preparation phase. This paper includes an overview of the experimental equipment properly developed by TRIGA staff. (authors)

  17. Dynamics model for real time diagnostics of TRIGA RC-1 system

    International Nuclear Information System (INIS)

    Gadomski, A.M.; Nanni, V.; Meo, G.B.

    1986-01-01

    This paper presents dynamics model of TRIGA RC-1 reactor system. The model is dedicated to the real-time early fault detection during a reactor operation in one week exploitation cycle. The algorithms are specially suited for real-time, long time and also accelerated simulations with assumed diagnostic oriented accuracy. The approximations, modular structure, numerical methods and validation are discussed. The elaborated model will be build in the TRIGA Supervisory System and TRIGA Diagnostic Simulator. (author)

  18. The application of the k0-standardization method at the TRIGA Mark II reactor, Ljubljana, Slovenia

    International Nuclear Information System (INIS)

    Jacimovic, Radojko; Benedik, Ljudmila; Stegnar, Peter; Smodis, Borut

    2002-01-01

    The k 0 -standardization method of neutron activation analysis (k 0 -NAA) was launched in the 1970s and since then continuously developed. Nowadays, k 0 -NAA became widespread as a practical analytical tool used to analyse different sample matrices. At the Jozef Stefan Institute (IJS), the KAYZERO/SOLCOI software package has been introduced for data processing after extensive testing and comparison with other available programs. In the process of validation of the software a suite of natural matrix reference materials (RMs) were used. Five certified reference materials (CRMs) from the Institute for Reference Materials and Measurements (IRMM), two standard reference materials (SRMs) from the National Institute of Standards and Technology (NIST), three RMs from the International Atomic Energy Agency (IAEA) and one RM from IJS were analysed. Altogether, results for ten elements in inorganic matrices and twenty-one elements in organic matrices, obtained by k 0 -instrumental neutron activation analysis (k 0 -INAA), were compared to certified values. The results obtained show good agreement with certified or assigned values except for Fe and U in inorganic matrices, and Al and Cr in organic matrices. (author)

  19. Current research work carried out at the 250 kW TRIGA Mark II reactor

    International Nuclear Information System (INIS)

    Dimic, V.; Kristof, E.; Rant, J.

    1972-01-01

    The main physics experiments accomplished during the last two years of the reactor operation include the cold neutron, fast neutron and n-gamma spectrometry, neutron radiography and in the radiochemical laboratory quite extensive program on neutron activation analysis is carried on the seed irradiation facilities in connection with the research contract with the IAEA were constructed. In additional, the connection of the reactor to the on-line computer CDC 1700 is finished. The task of this work is the monitoring and control of the reactor power level and other operating conditions. This paper deals briefly only with the cold neutron, fast neutron and n-gamma spectrometry. The other fields of activity at our reactor will be described more in detail in the separate papers presented in this section

  20. Corrosion in the aluminum containment tank at the Nuclear Center of Mexico TRIGA Mark III reactor

    International Nuclear Information System (INIS)

    Mota, Juan Ramon

    1986-01-01

    The reactor developed a leak inside the exposure room discovered when it was opened for a routine inspection. This leak started to diminish immediately after it was found and disappeared completely in 2.5 months. The hydrostatic tests of the exposure room cooling water pipes and of the primary cooling system suction pipe proved that piping do not have leaks. A portion of the total volume of water was drained from the pool to conduct an inspection on the aluminum liner. Penetrant dye tests were initiated over welded Joints and walls. Welded Joints were all found to be in good condition but a total of 35 indications were reported on walls and concentrated on two main areas. A vacuum system was used to test for leakage. Seven indications were found to be perforations that crossed through the wall, fifteen indications did not cross through the wall but required repair and the rest were superficial irregularities. For the inspection of surfaces that remained covered by water, two methods were used. One was a television camera that was adapted to be used under water and hooked to a monitor and a videorecorder for close up inspection of the walls. The other consisted of submarine still color photography performed by divers. The evaluation of these inspections concluded that out of the 10 areas previously identified, only one presented the kind of problem that required repair. The last inspection performed was that using ultrasound techniques. Irregularities found did not require complete replacement of the aluminum liner. The repair procedures included the welding of aluminum plates over damaged areas and the injection of an effective insulating material (resin) to stop the corrosion mechanism