UMTRA Project Site Observational Work Plan, Mexican Hat, Utah

International Nuclear Information System (INIS)

1994-09-01

Surface cleanup activities at the Mexican Hat UMTRA processing site are nearing completion. Ground Water contamination at the Mexican Hat site is a result of uranium milling operations. The extent of residual process water has been identified, and it is limited to the uppermost aquifer in the vicinity of the site. Deeper aquifers are not affected because of an upward hydraulic gradient and the presence of a confining unit (the deeper aquifers are protected by hydrogeologic isolation). The uppermost unit is returning to its pre-milling, mainly unsaturated state. The unit that contains the contaminated water is not a ground water resource because it qualifies as Class III (limited use) based on limited yield. Ground water in the uppermost unit is currently not used and is not anticipated to be used as a ground water resource. The nearby San Juan River and a converted oil exploration well provide all of the water needs for the area. There are no current threats to human health or livestock; and, because the zone of contamination does not represent a ground water resource, none are anticipated in the future. There are, however, seeps where contaminated water is exposed at land surface. The seeps create potential exposure pathways for plants and wildlife. It is not known at this time if there is a risk to the environment. Additional investigations are needed and are described in this document to confirm the presence or absence of potential environmental risks. Additional hydrogeologic investigations are not required. The proposed ground water compliance strategy for the site is no remediation, because the ground water in the uppermost aquifer (which is also the zone of contamination) qualifies for supplemental standards based on Class III, limited yield, and because there are no threats to human health. Domestic and agricultural water is pumped from a deeper aquifer that is isolated from the contaminated zone

Site observational work plan for the UMTRA Project Site at Riverton, Wyoming. Revision 3/95

International Nuclear Information System (INIS)

1995-03-01

Ground water compliance for the Uranium Mill Tailings Remedial Action (UMTRA) Project sites, including the Riverton, Wyoming, site, is governed by the Uranium Mill Tailings Radiation Control Act and the US Environmental Protection Agency's Health and Environmental Protection Standards for Uranium and Thorium Mill Tailings. The compliance strategy proposed for this site is natural flushing in conjunction with institutional controls. The essential premise of natural flushing is that ground water movement and natural attenuation processes will reduce the detected contamination to background levels or alternate concentration limits that do not pose a risk to human health or the environment within 100 years. This document contains the following sections. Section 2.0 of this SOWP describes the requirements for meeting standards at UMTRA Project sites. Section 3.0 provides site-specific data and the related conceptual model. Section 4.0 provides the justification for the recommended ground water compliance strategy for the Riverton site. Section 5.0 provides the justification and process for collection and assessment of additional required data. Section 6.0 provides a list of the references cited. The appendixes include data on monitor wells and lithography, ground water, surface water, and sediment quality

Burn site groundwater interim measures work plan.

Energy Technology Data Exchange (ETDEWEB)

Witt, Jonathan L. (North Wind, Inc., Idaho Falls, ID); Hall, Kevin A. (North Wind, Inc., Idaho Falls, ID)

2005-05-01

This Work Plan identifies and outlines interim measures to address nitrate contamination in groundwater at the Burn Site, Sandia National Laboratories/New Mexico. The New Mexico Environment Department has required implementation of interim measures for nitrate-contaminated groundwater at the Burn Site. The purpose of interim measures is to prevent human or environmental exposure to nitrate-contaminated groundwater originating from the Burn Site. This Work Plan details a summary of current information about the Burn Site, interim measures activities for stabilization, and project management responsibilities to accomplish this purpose.

7 CFR 1948.83 - Performance of site development work.

Science.gov (United States)

2010-01-01

... 7 Agriculture 13 2010-01-01 2009-01-01 true Performance of site development work. 1948.83 Section 1948.83 Agriculture Regulations of the Department of Agriculture (Continued) RURAL HOUSING SERVICE... Development Assistance Program § 1948.83 Performance of site development work. Site development work will be...

Web sites that work secrets from winning web sites

CERN Document Server

Smith, Jon

2012-01-01

Leading web site entrepreneur Jon Smith has condensed the secrets of his success into 52 inspiring ideas that even the most hopeless technophobe can implement. The brilliant tips and practical advice in Web sites that work will uplift and transform any website, from the simplest to the most complicated. It deals with everything from fundamentals such as how to assess the effectiveness of a website and how to get a site listed on the most popular search engines to more sophisticated challenges like creating a community and dealing with legal requirements. Straight-talking, practical and humorou

Radiation survey and management on the reconstructed radioactive work-site

International Nuclear Information System (INIS)

Yu Tao; Liang Shiqiang; Wang Youmei

2004-12-01

The experiences of radiation survey and administration in the prophase on reconstructed radioactive work-site are summarized. The advance works are to investigate the reconstructed work-site, settle working plans, devise inspecting flow charts, deal with something in time in the local and train the staffers. The works about prophasic decontaminating, removing and cleaning up the site have been finished, which have established the deep foundation to develop later task. (authors)

The observational approach for site remediation at federal facilities

International Nuclear Information System (INIS)

Myers, R.S.; Gianti, S.J.

1989-11-01

The observational approach, developed by geotechnical engineers to cope with the uncertainty associated with subsurface construction such as tunnels and dams, can be applied to hazardous waste site remediation. During the last year, the observational approach has gained increasing attention as a means of addressing the uncertainties involved in site remediation. In order to evaluate the potential advantages and constraints of applying the observational approach to site restoration at federal facilities, a panel of scientists and engineers from Pacific Northwest Laboratory and CH2M Hill was convened. Their review evaluated potential technical and institutional advantages and constraints that may affect the use of the observational approach for site remediation. This paper summarizes the panel's comments and conclusions about the application of the observational approach to site remediation at federal facilities. Key issues identified by the panel include management of uncertainty, cost and schedule, regulations and guidance, public involvement, and implementation. 5 refs

Remedial action work plan for the Colonie site. Revision 1

International Nuclear Information System (INIS)

1985-08-01

The Colonie site is a DOE Formerly Utilized Sites Remedial Action Program (FUSRAP) site located in the Town of Colonie, New York, and consisting of an interim storage site and several vicinity properties. The Colonie Interim Storage Site (CISS) is the former National Lead (NL) Industries plant located at 1130 Central Avenue. There are 11 vicinity properties that received remedial action in 1984: 7 located south of the site on Yardboro and Palmer Avenues just across the Colonie-Albany town limits in Albany, and 4 located northwest of the site along Central Avenue in Colonie. Of these properties, nine are residences and two are commercial properties. This document describes the engineering design, construction, and associated plans for remedial action on the vicinity properties and the interim storage site. These plans include both radiological and chemical work. Radiological work includes: excavating the above-guideline radioactive wastes on the vicinity properties; designing required facilities for the interim storage site; preparing the interim storage site to receive these contaminated materials; transporting the contaminated materials to the interim waste storage stockpile; and preparing necessary schedules for accomplishing the remedial actions. Chemical work involves: developing the Resource Conservation and Recovery Act (RCRA) closure plans; neutralizing chemical hazards associated with plating solutions; inventorying on-site chemicals; and disposal of chemicals and/or residues. 17 refs., 5 figs., 1 tab

Predicting on-site environmental impacts of municipal engineering works

International Nuclear Information System (INIS)

Gangolells, Marta; Casals, Miquel; Forcada, Núria; Macarulla, Marcel

2014-01-01

The research findings fill a gap in the body of knowledge by presenting an effective way to evaluate the significance of on-site environmental impacts of municipal engineering works prior to the construction stage. First, 42 on-site environmental impacts of municipal engineering works were identified by means of a process-oriented approach. Then, 46 indicators and their corresponding significance limits were determined on the basis of a statistical analysis of 25 new-build and remodelling municipal engineering projects. In order to ensure the objectivity of the assessment process, direct and indirect indicators were always based on quantitative data from the municipal engineering project documents. Finally, two case studies were analysed and found to illustrate the practical use of the proposed model. The model highlights the significant environmental impacts of a particular municipal engineering project prior to the construction stage. Consequently, preventive actions can be planned and implemented during on-site activities. The results of the model also allow a comparison of proposed municipal engineering projects and alternatives with respect to the overall on-site environmental impact and the absolute importance of a particular environmental aspect. These findings are useful within the framework of the environmental impact assessment process, as they help to improve the identification and evaluation of on-site environmental aspects of municipal engineering works. The findings may also be of use to construction companies that are willing to implement an environmental management system or simply wish to improve on-site environmental performance in municipal engineering projects. -- Highlights: • We present a model to predict the environmental impacts of municipal engineering works. • It highlights significant on-site environmental impacts prior to the construction stage. • Findings are useful within the environmental impact assessment process. • They also

Predicting on-site environmental impacts of municipal engineering works

Energy Technology Data Exchange (ETDEWEB)

Gangolells, Marta, E-mail: marta.gangolells@upc.edu; Casals, Miquel, E-mail: miquel.casals@upc.edu; Forcada, Núria, E-mail: nuria.forcada@upc.edu; Macarulla, Marcel, E-mail: marcel.macarulla@upc.edu

2014-01-15

The research findings fill a gap in the body of knowledge by presenting an effective way to evaluate the significance of on-site environmental impacts of municipal engineering works prior to the construction stage. First, 42 on-site environmental impacts of municipal engineering works were identified by means of a process-oriented approach. Then, 46 indicators and their corresponding significance limits were determined on the basis of a statistical analysis of 25 new-build and remodelling municipal engineering projects. In order to ensure the objectivity of the assessment process, direct and indirect indicators were always based on quantitative data from the municipal engineering project documents. Finally, two case studies were analysed and found to illustrate the practical use of the proposed model. The model highlights the significant environmental impacts of a particular municipal engineering project prior to the construction stage. Consequently, preventive actions can be planned and implemented during on-site activities. The results of the model also allow a comparison of proposed municipal engineering projects and alternatives with respect to the overall on-site environmental impact and the absolute importance of a particular environmental aspect. These findings are useful within the framework of the environmental impact assessment process, as they help to improve the identification and evaluation of on-site environmental aspects of municipal engineering works. The findings may also be of use to construction companies that are willing to implement an environmental management system or simply wish to improve on-site environmental performance in municipal engineering projects. -- Highlights: • We present a model to predict the environmental impacts of municipal engineering works. • It highlights significant on-site environmental impacts prior to the construction stage. • Findings are useful within the environmental impact assessment process. • They also

Site Characterization Work Plan for Gnome-Coach Site, New Mexico

Energy Technology Data Exchange (ETDEWEB)

DOE/NV

2001-02-13

Project Gnome was the first nuclear experiment conducted under the U.S. Atomic Energy Commission (AEC), predecessor to the U.S. Department of Energy (DOE), Plowshare Program. Gnome was part of a joint government-industry experiment focused on developing nuclear devices exclusively for peaceful purposes. The intent of the Gnome experiment was to evaluate the effects of a nuclear detonation in a salt medium. Historically, Project Gnome consisted of a single detonation of a nuclear device on December 10, 1961. Since the Gnome detonation, the AEC/DOE has conducted surface restoration, site reconnaissance, and decontamination and decommissioning activities at the site. In addition, annual groundwater sampling is performed under a long-term hydrological monitoring program begun in 1980. Coach, an experiment to be located near the Gnome project, was initially scheduled for 1963. Although construction and rehabilitation were completed for Coach, the experiment was canceled and never executed. Known collectively as Project Gnome-Coach, the site is situated within the Salado Formation approximately 25 miles east of Carlsbad, New Mexico, in Eddy County, and is comprised of nearly 680 acres, of which 60 acres are disturbed from the combined AEC/DOE operations. The scope of this work plan is to document the environmental objectives and the proposed technical site investigation strategies that will be utilized for the site characterization of the project. The subsurface at the Gnome-Coach site has two contaminant sources that are fundamentally different in terms of both their stratigraphic location and release mechanism. The goal of this characterization is to collect data of sufficient quantity and quality to establish current site conditions and to use the data to identify and evaluate if further action is required to protect human health and the environment and achieve permanent closure of the site. The results of these activities will be presented in a subsequent corrective

Predicting on-site environmental impacts of municipal engineering works

OpenAIRE

Gangolells Solanellas, Marta; Casals Casanova, Miquel; Forcada Matheu, Núria; Macarulla Martí, Marcel

2014-01-01

The research findings fill a gap in the body of knowledge by presenting an effective way to evaluate the significance of on-site environmental impacts of municipal engineering works prior to the construction stage. First, 42 on-site environmental impacts of municipal engineering works were identified by means of a process-oriented approach. Then, 46 indicators and their corresponding significance limits were determined on the basis of a statistical analysis of 25 new-build and remodelling mun...

Multi-site pain and working conditions as predictors of work ability in a 4-year follow-up among food industry employees.

Science.gov (United States)

Neupane, S; Virtanen, P; Leino-Arjas, P; Miranda, H; Siukola, A; Nygård, C-H

2013-03-01

We investigated the separate and joint effects of multi-site musculoskeletal pain and physical and psychosocial exposures at work on future work ability. A survey was conducted among employees of a Finnish food industry company in 2005 (n = 1201) and a follow-up survey in 2009 (n = 734). Information on self-assessed work ability (current work ability on a scale from 0 to 10; 7 = poor work ability), multi-site musculoskeletal pain (pain in at least two anatomical areas of four), leisure-time physical activity, body mass index and physical and psychosocial exposures was obtained by questionnaire. The separate and joint effects of multi-site pain and work exposures on work ability at follow-up, among subjects with good work ability at baseline, were assessed by logistic regression, and p-values for the interaction derived. Compared with subjects with neither multi-site pain nor adverse work exposure, multi-site pain at baseline increased the risk of poor work ability at follow-up, allowing for age, gender, occupational class, body mass index and leisure-time physical activity. The separate effects of the work exposures on work ability were somewhat smaller than those of multi-site pain. Multi-site pain had an interactive effect with work environment and awkward postures, such that no association of multi-site pain with poor work ability was seen when work environment was poor or awkward postures present. The decline in work ability connected with multi-site pain was not increased by exposure to adverse physical or psychosocial factors at work. © 2012 European Federation of International Association for the Study of Pain Chapters.

Deconstructing thermodynamic parameters of a coupled system from site-specific observables.

Science.gov (United States)

Chowdhury, Sandipan; Chanda, Baron

2010-11-02

Cooperative interactions mediate information transfer between structural domains of a protein molecule and are major determinants of protein function and modulation. The prevalent theories to understand the thermodynamic origins of cooperativity have been developed to reproduce the complex behavior of a global thermodynamic observable such as ligand binding or enzyme activity. However, in most cases the measurement of a single global observable cannot uniquely define all the terms that fully describe the energetics of the system. Here we establish a theoretical groundwork for analyzing protein thermodynamics using site-specific information. Our treatment involves extracting a site-specific parameter (defined as χ value) associated with a structural unit. We demonstrate that, under limiting conditions, the χ value is related to the direct interaction terms associated with the structural unit under observation and its intrinsic activation energy. We also introduce a site-specific interaction energy term (χ(diff)) that is a function of the direct interaction energy of that site with every other site in the system. When combined with site-directed mutagenesis and other molecular level perturbations, analyses of χ values of site-specific observables may provide valuable insights into protein thermodynamics and structure.

Work management administration FY 1995 site support program plan WBS 6.2

Energy Technology Data Exchange (ETDEWEB)

Hale, N.S.

1994-09-01

Westinghouse Hanford Company`s (WHC) near-term vision is to implement a Site-wide work management program that is consistent from one facility to the other, and can realize workforce efficiencies, minimum down time, and familiarization with facilities uniqueness. Additionally, consistent Hanford Site work management processes can produce meaningful information to be shared complex-wide as the US Department of Energy (DOE) cleans up facilities Site-wide. It is the mission of the WHC Work Management Administration Program to provide guidance and program direction on how to implement consistent and effective work management across the Hanford Site that comply with the DOE and other regulatory requirements. This report describes the steps needed to implement a work management plan at Hanford.

29 CFR 785.12 - Work performed away from the premises or job site.

Science.gov (United States)

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Work performed away from the premises or job site. 785.12... of Principles Employees âsuffered Or Permittedâ to Work § 785.12 Work performed away from the premises or job site. The rule is also applicable to work performed away from the premises or the job site...

Sectored Clean-up Work Plan for Housekeeping Category Waste Sites

International Nuclear Information System (INIS)

Nacht, S. J.

2000-01-01

The Sectored Clean-up Work Plan (SCWP) replaces the Housekeeping Category Corrective Action Unit Work Plan and provides a strategy to be used for conducting housekeeping activities using a sectored clean-up approach. This work plan provides a process by which one or more existing housekeeping category Corrective Action Sites (CASS) from the Federal Facility Agreement and Consent Order and/or non-FFACO designated waste site(s) are grouped into a sector for simultaneous remediation and cleanup. This increases effectiveness and efficiencies in labor, materials, equipment, cost, and time. This plan is an effort by the U.S. Department of Energy to expedite work in a more organized and efficient approach. The objectives of this plan are to: Group housekeeping FFACO CASS and non-FFACO housekeeping sites into sectors and remediate during the same field visit; Provide consistent documentation on FFACO CAS and non-FFACO clean-up activities; Perform similar activities under one approved document; Remediate areas inside the Deactivation and Decommissioning facilities and compounds in a campaign-style remediation; and Increase efficiencies and cost-effectiveness, accelerate cleanups, reduce mobilization, demobilization, and remediation costs

Integration of a working site in its regional context

International Nuclear Information System (INIS)

Couture, J.

1986-01-01

This paper shows how a local representative has felt the decision of construction of the Paluel nuclear power plant and the problems involved, and how it has been tried to resolve them: insertion in the site, reception of the population of this big working site [fr

Occupational exposure to crystalline silica at Alberta work sites.

Science.gov (United States)

Radnoff, Diane; Todor, Maria S; Beach, Jeremy

2014-01-01

Although crystalline silica has been recognized as a health hazard for many years, it is still encountered in many work environments. Numerous studies have revealed an association between exposure to respirable crystalline silica and the development of silicosis and other lung diseases including lung cancer. Alberta Jobs, Skills, Training and Labour conducted a project to evaluate exposure to crystalline silica at a total of 40 work sites across 13 industries. Total airborne respirable dust and respirable crystalline silica concentrations were quite variable, but there was a potential to exceed the Alberta Occupational Exposure Limit (OEL) of 0.025 mg/m(3) for respirable crystalline silica at many of the work sites evaluated. The industries with the highest potentials for overexposure occurred in sand and mineral processing (GM 0.090 mg/m(3)), followed by new commercial building construction (GM 0.055 mg/m(3)), aggregate mining and crushing (GM 0.048 mg/m(3)), abrasive blasting (GM 0.027 mg/m(3)), and demolition (GM 0.027 mg/m(3)). For worker occupations, geometric mean exposure ranged from 0.105 mg/m(3) (brick layer/mason/concrete cutting) to 0.008 mg/m(3) (dispatcher/shipping, administration). Potential for GM exposure exceeding the OEL was identified in a number of occupations where it was not expected, such as electricians, carpenters and painters. These exposures were generally related to the specific task the worker was doing, or arose from incidental exposure from other activities at the work site. The results indicate that where there is a potential for activities producing airborne respirable crystalline silica, it is critical that the employer include all worker occupations at the work site in their hazard assessment. There appears to be a relationship between airborne total respirable dust concentration and total respirable dust concentrations, but further study is require to fully characterize this relationship. If this relationship holds true

Attitudes toward smoking restrictions in work sites, restaurants, and bars among North Carolinians.

Science.gov (United States)

Maguire, Rachel Loflin; Brinkley, Jason; Mansfield, Christopher

2010-01-01

Public support for smoking restrictions has increased in recent years, but support varies among groups and according to where restrictions should apply. National studies show that Americans are less likely to favor smoking restrictions in restaurants and bars than at other work sites but that the support varies across segments of the population. A full examination of the changes and status of attitudes toward smoking restrictions by site and across subgroups in North Carolina has not been undertaken. Data from US Census Bureau Current Population Surveys conducted during 2001-2002 and 2006-2007 were analyzed. Trends in attitudes toward smoke-free policies at indoor work sites, restaurants, and bars are presented overall and by occupation, smoking status, income, race/ethnicity, workplace smoking policy, age, sex, and education. Logistic regression was used to identify key factors predicting support for smoke-free policies at work sites. Support for smoke-free policies increased by at least 7.4 percentage points at each venue between 2001-2002 and 2006-2007. In 2006-2007, the strongest public support for smoking restrictions was reported for work sites (69.6%), followed by restaurants (52.3%) and bars (36.1%). Whether a person smokes is the strongest predictor of their attitude about smoking restrictions in indoor work sites. Data are self-reported, from independent samples, and lack county identifiers. There is substantial and increasing public support for smoke-free policies in North Carolina. These findings show extensive support for extending smoking bans to all indoor work sites, with nearly 70% of respondents in 2006-2007 favoring smoke-free work sites.

Work-related injuries and fatalities in the geotechnical site works.

Science.gov (United States)

Akboğa Kale, Özge; Eskişar, Tuğba

2018-05-19

Geotechnical site works are comprehensive, and they constitute the first step of the construction process. This study performs data mining of geotechnical works and analyzes the database for the root causes of accidents. The Occupational Safety and Health Administration (OSHA) was chosen for the 1984-2013 time frame with 247 cases. Descriptive statistical analyses were performed to discuss variables such as the end use of the work, project type and cost, soil type and condition, type and degree of injury, cause and type of accident, unsafe acts, and occupation and union status of the victim. The results showed that these accidents have a high frequency of recurrence and have a high severity level (54.3% fatalities). In addition, a total of 838 violations were recorded with penalties reaching 5 million US dollars. This study emphasizes that project-specific countermeasures should be taken regarding the root causes of accidents, leading to vigorous strategies to develop safety measures.

ROAD REPAIR WORKS ON THE MEYRIN SITE

CERN Multimedia

ST-TFM Group

2001-01-01

ST Division will proceed, as from Monday 23 July, in repairing some parts of roads on the Meyrin site (see drawing). This work will last for one week depending on the weather conditions and will cause some traffic hold ups during this period. Please follow the indications on the temporary road signs. Thanking you in advance for your comprehension.

Establishing the Antarctic Dome C community reference standard site towards consistent measurements from Earth observation satellites

Science.gov (United States)

Cao, C.; Uprety, S.; Xiong, J.; Wu, A.; Jing, P.; Smith, D.; Chander, G.; Fox, N.; Ungar, S.

2010-01-01

Establishing satellite measurement consistency by using common desert sites has become increasingly more important not only for climate change detection but also for quantitative retrievals of geophysical variables in satellite applications. Using the Antarctic Dome C site (75°06′S, 123°21′E, elevation 3.2 km) for satellite radiometric calibration and validation (Cal/Val) is of great interest owing to its unique location and characteristics. The site surface is covered with uniformly distributed permanent snow, and the atmospheric effect is small and relatively constant. In this study, the long-term stability and spectral characteristics of this site are evaluated using well-calibrated satellite instruments such as the Moderate Resolution Imaging Spectroradiometer (MODIS) and Sea-viewing Wide Field-of-view Sensor (SeaWiFS). Preliminary results show that despite a few limitations, the site in general is stable in the long term, the bidirectional reflectance distribution function (BRDF) model works well, and the site is most suitable for the Cal/Val of reflective solar bands in the 0.4–1.0 µm range. It was found that for the past decade, the reflectivity change of the site is within 1.35% at 0.64 µm, and interannual variability is within 2%. The site is able to resolve calibration biases between instruments at a level of ~1%. The usefulness of the site is demonstrated by comparing observations from seven satellite instruments involving four space agencies, including OrbView-2–SeaWiFS, Terra–Aqua MODIS, Earth Observing 1 (EO-1) – Hyperion, Meteorological Operational satellite programme (MetOp) – Advanced Very High Resolution Radiometer (AVHRR), Envisat Medium Resolution Imaging Spectrometer (MERIS) – dvanced Along-Track Scanning Radiometer (AATSR), and Landsat 7 Enhanced Thematic Mapper Plus (ETM+). Dome C is a promising candidate site for climate quality calibration of satellite radiometers towards more consistent satellite measurements, as part

Draft Site Management and Monitoring Plan for Corpus Christi Maintenance and New Work Ocean Dredged Material Disposal Site

Science.gov (United States)

USEPA Region 6 and the US Army Corps of Engineers submit for public comment the Draft Site Management and Monitoring Plan for Corpus Christi Maintenance and New Work Ocean Dredged Material Disposal Site

Work characteristics predict the development of multi-site musculoskeletal pain

NARCIS (Netherlands)

Oakman, J.; Wind, A. de; Heuvel, S.G. van den; Beek, A.J. van der

2017-01-01

Purpose. Musculoskeletal pain in more than one body region is common and a barrier to sustaining employment. We aimed to examine whether work characteristics predict the development of multi-site pain (MSP), and to determine differences in work-related predictors between age groups. Methods. This

Work-related determinants of multi-site musculoskeletal pain among employees in the health care sector.

Science.gov (United States)

Neupane, Subas; Nygård, Clas-Håkan; Oakman, Jodi

2016-06-16

Work-related musculoskeletal pain is a major occupational problem. Those with pain in multiple sites usually report worse health outcomes than those with pain in one site. This study explored prevalence and associated predictors of multi-site pain in health care sector employees. Survey responses from 1348 health care sector employees across three organisations (37% response rate) collected data on job satisfaction, work life balance, psychosocial and physical hazards, general health and work ability. Musculoskeletal discomfort was measured across 5 body regions with pain in ≥ 2 sites defined as multi-site pain. Generalized linear models were used to identify relationships between work-related factors and multi-site pain. Over 52% of the employees reported pain in multiple body sites and 19% reported pain in one site. Poor work life balance (PRR = 2.33, 95% CI = 1.06-5.14). physical (PRR = 7.58, 95% CI = 4.89-11.77) and psychosocial (PRR = 1.59, 95% CI = 1.00-2.57) hazard variables were related to multi-site pain (after controlling for age, gender, health and work ability. Older employees and females were more likely to report multi-site pain. Effective risk management of work related multi-site pain must include identification and control of psychosocial and physical hazards.

Road repair works on the Meyrin site

CERN Multimedia

2003-01-01

ST Division will proceed, as from Monday 15th of September, in repairing some parts of roads on the Meyrin site (see drawing). This work will last for three weeks depending on the weather conditions and will cause some traffic hold ups during this period. Please follow the indications on the temporary road signs. Thanking you in advance for your comprehension. ST-CE and ST-FM Groups GSM 160224 - 163976

The alternative site selection procedure as covered in the report by the Repository Site Selection Procedures Working Group

International Nuclear Information System (INIS)

Brenner, M.

2005-01-01

The 2002 Act on the Regulated Termination of the Use of Nuclear Power for Industrial Electricity Generation declared Germany's opting out of the peaceful uses of nuclear power. The problem of the permanent management of radioactive residues is becoming more and more important also in the light of that political decision. At the present time, there are no repositories offering the waste management capacities required. Such facilities need to be created. At the present stage, eligible repository sites are the Konrad mine, a former iron ore mine near Salzgitter, and the Gorleben salt dome. While the fate of the Konrad mine as a repository for waste generating negligible amounts of heat continues to be uncertain, despite a plan approval decision of June 2002, the Gorleben repository is still in the planning phase, at present in a dormant state, so to speak. The federal government expressed doubt about the suitability of the Gorleben site. Against this backdrop, the Federal Ministry for the Environment, Nature Conservation, and Nuclear Safety in February 1999 established AkEnd, the Working Group on Repository Site Selection Procedures. The Group was charged with developing, based on sound scientific criteria, a transparent site selection procedure in order to facilitate the search for repository sites. The Working Group presented its final report in December 2002 after approximately four years of work. The Group's proposals about alternative site selection procedures are explained in detail and, above all, reviewed critically. (orig.)

Direct observation of the lattice sites of implanted manganese in silicon

CERN Document Server

Silva, Daniel; Wahl, Ulrich; Martins Correia, Joao; Amorim, Lígia; Decoster, Stefan; Castro Ribeiro Da Silva, Manuel; Da Costa Pereira, Lino Miguel; Esteves De Araujo, Araujo Joao Pedro

2016-01-01

Mn-doped Si has attracted significant interest in the context of dilute magnetic semiconductors. We investigated the lattice location of implanted Mn in silicon of different doping types (n, n+ and p+) in the highly dilute regime. Three different lattice sites were identified by means of emission channeling experiments: ideal substitutional sites; sites displaced from bond-centered towards substitutional sites and sites displaced from anti-bonding towards tetrahedral interstitial sites. For all doping types investigated, the substitutional fraction remained below ∼ 30%. We discuss the origin of the observed lattice sites as well as the implications of such structures on the understanding of Mn-doped Si systems.

Reliability and criterion validity of an observation protocol for working technique assessments in cash register work.

Science.gov (United States)

Palm, Peter; Josephson, Malin; Mathiassen, Svend Erik; Kjellberg, Katarina

2016-06-01

We evaluated the intra- and inter-observer reliability and criterion validity of an observation protocol, developed in an iterative process involving practicing ergonomists, for assessment of working technique during cash register work for the purpose of preventing upper extremity symptoms. Two ergonomists independently assessed 17 15-min videos of cash register work on two occasions each, as a basis for examining reliability. Criterion validity was assessed by comparing these assessments with meticulous video-based analyses by researchers. Intra-observer reliability was acceptable (i.e. proportional agreement >0.7 and kappa >0.4) for 10/10 questions. Inter-observer reliability was acceptable for only 3/10 questions. An acceptable inter-observer reliability combined with an acceptable criterion validity was obtained only for one working technique aspect, 'Quality of movements'. Thus, major elements of the cashiers' working technique could not be assessed with an acceptable accuracy from short periods of observations by one observer, such as often desired by practitioners. Practitioner Summary: We examined an observation protocol for assessing working technique in cash register work. It was feasible in use, but inter-observer reliability and criterion validity were generally not acceptable when working technique aspects were assessed from short periods of work. We recommend the protocol to be used for educational purposes only.

First observed roost site of Vervain Hummingbird (mellisuga minima)

Science.gov (United States)

P.B. Hamel

2012-01-01

An observation of a roost site of a male Vervain Hummingbird in the Dominican Republic on 7 November 2010 is the first for this species. The bird chose an entirely exposed position on a very thin twig,

Work plan for monitor well installation water and sediment sample collection aquifer testing and topographic surveying at the Riverton, Wyoming, UMTRA Project Site

International Nuclear Information System (INIS)

1995-06-01

Investigations conducted during preparation of the site observational work plan (SOWP) at the Uranium Mill Tailings Remedial Action (UMTRA) Project site support a proposed natural flushing ground water compliance strategy, with institutional controls. However, additional site-specific data are needed to reduce uncertainties in order to confirm the applicability and feasibility of this proposed compliance strategy option. This proposed strategy will be analyzed in the site-specific environmental assessment. The purpose of this work plan is to summarize the data collection objectives to fill those data needs, describe the data collection activities that will be undertaken to meet those objectives, and elaborate on the data quality objectives which define the procedures that will be followed to ensure that the quality of these data meet UMTRA Project needs

Securing a Wireless Site Network to Create a BIM-Allied Work-Front

Directory of Open Access Journals (Sweden)

Payam R. Zekavat

2014-08-01

Full Text Available The Building Information Model (BIM serves as a framework to align all the project-related data, providing interoperability to store and retrieve information interactively. Unfortunately, the construction site itself is excluded from this interaction as the large amount of data requires high data transfer rates and ruggedized hardware. However, advanced wireless communication technologies open radically new avenues to relay large amounts of data automatically and in near real-time. Construction could be a key beneficiary of these advancements. Wireless communication integrated with BIM, GPS and the Internet is able to provide the backbone necessary for creating intelligent systems, supporting the designer in his or her office as well as workers on the work-front. This paper presents a study that documents the development and testing of prototypes designed to facilitate information sharing at the field-level during construction. The main system constitutes an information hub, called the eCKiosk, connecting “senders and receivers” both on-site as well as off-site. The system design is discussed and some of the main modules are demonstrated. Since the electronic Kiosk depends on robust connections to the wireless devices distributed across the site, reliable connectivity is essential. For this reason, the discussion includes a study of the electronic signals behaviour in an ever-changing construction site. Measurements of the signal strengths during excavation and concrete work are presented and compared with theoretical calculations used to predict wave propagation. The results show how present models overestimate signal attenuation patterns on the construction site. This is important for designing a reliable and secure wireless site networks to link BIM to the work-front.

Preferential site occupancy observed in coexpanded argon-krypton clusters

International Nuclear Information System (INIS)

Lundwall, M.; Bergersen, H.; Lindblad, A.; Oehrwall, G.; Svensson, S.; Bjoerneholm, O.; Tchaplyguine, M.

2006-01-01

Free heterogeneous argon-krypton clusters have been produced by coexpansion and investigated by means of x-ray photoelectron spectroscopy. By examining cluster surface and bulk binding energy shifts, relative intensities, and peak widths, we show that in the mixed argon-krypton clusters the krypton atoms favor the bulk and argon atoms are pushed to the surface. Furthermore, we show that krypton atoms in the surface layer occupy high-coordination sites and that heterogeneous argon-krypton clusters produced by coexpansion show the same surface structure as argon host clusters doped with krypton. These observations are supported by site-dependent calculations of chemical shifts

Meteorology in site operations

International Nuclear Information System (INIS)

Anon.

1986-01-01

During the site selection and design phases of a plant, meteorological assistance must be based on past records, usually accumulated at stations not actually on the site. These preliminary atadvices will be averages and extremes that might be expected. After a location has been chosen and work has begun, current and forecast weather conditions become of immediate concern. On-site meteorological observations and forecasts have many applications to the operating program of an atomic energy site. Requirements may range from observations of the daily minimum temperatures to forecasts of radiation dosages from airborne clouds

State preemption of local smoke-free laws in government work sites, private work sites, and restaurants - United States, 2005-2009.

Science.gov (United States)

2010-02-05

Smoke-free policies (i.e., policies that completely eliminate smoking in indoor workplaces and public places) result in health benefits, including preventing heart attacks. Preemptive legislation at the state level prohibits localities from enacting laws that vary from state law or are more stringent. A Healthy People 2010 objective (27-19) is to eliminate state laws that preempt stronger local tobacco control laws. A 2005 CDC review found that little progress was being made toward reducing the number of state laws preempting local smoking restrictions in three indoor settings: government work sites, private-sector work sites, and restaurants. These three settings were selected for analysis because they are settings that often are addressed by state and local smoking restrictions and because they are major settings where nonsmoking workers and patrons are exposed to secondhand smoke. This report updates the previous analysis and summarizes changes that occurred from December 31, 2004, to December 31, 2009, in state laws that preempt local smoke-free laws for the same three settings. During that period, the number of states preempting local smoking restrictions in at least one of these three settings decreased from 19 to 12. In contrast with the 2005 findings, this decrease indicates progress toward achieving the goal of eliminating state laws preempting local smoking restrictions. Further progress could result in additional reductions in secondhand smoke exposure.

Site Characterization Work Plan for the Gnome-Coach Site, New Mexico (Rev. 1, January 2002)

Energy Technology Data Exchange (ETDEWEB)

U.S. Department of Energy, National Nuclear Security Administration Nevada Operations Office (NNSA/NV)

2002-01-14

Project Gnome was the first nuclear experiment conducted under the U.S. Atomic Energy Commission (AEC), predecessor to the U.S. Department of Energy (DOE), Plowshare Program. The Plowshare Program focused on developing nuclear devices exclusively for peaceful purposes. The intent of the Gnome experiment was to evaluate the effects of a nuclear detonation in a salt medium. Historically, Project Gnome consisted of a single detonation of a nuclear device on December 10, 1961 with the Salado Formation. Since the Gnome detonation, the AEC/DOE has conducted surface restoration, site reconnaissance, and decontamination and decommissioning activities at the site. In addition, annual groundwater sampling is performed under a long-term hydrological monitoring program begun in 1972. Coach, an experiment to be located near the Gnome project, was initially scheduled for 1963. Although construction and rehabilitation were completed for Coach, the experiment was canceled and never executed. Known collectively as Project Gnome-Coach, the site is located approximately 25 miles east of Carlsbad, New Mexico, in Eddy County, and is comprised of nearly 680 acres, of which approximately 60 acres are disturbed from the combined AEC/DOE operations. The scope of this work plan is to document the environmental objectives and the proposed technical site investigation strategies that will be utilized for the site characterization of the project. The subsurface at the Gnome-Coach site has two contaminant sources that are fundamentally different in terms of both their stratigraphic location and release mechanism. The goal of this characterization is to collect data of sufficient quantity and quality to establish current site conditions and to use the data to identify and evaluate if further action is required to protect human health and the environment and achieve permanent closure of the site. The results of these activities will be presented in a subsequent corrective action decision document.

The Selection and Protection of Optical Astronomical Observing Sites in China

Science.gov (United States)

Wenjing, Jin; Bai, Jinming; Yao, Yongqiang

2015-03-01

Before 1950 there are two observatories, Shanghai and Purple Mountain Astronomical Observatories (SHAO and PMO), and two observing stations, Qingdao and Kunming stations in China. With the requirements of astronomical research, two observatories, Beijing and Shaanxi Astronomical Observatories (BAO and SXAO) and two artificial satellite stations, Urumqi and Changchun, were established about 1960. Based on the current management, now there are 4 observatories, SHAO, PMO, NAOC(National Astronomical Observatories), which was grouped from BAO, YNAO and 2 others, as well as XAO (Xinjiang Astronomical Observatory). The optical 1-2 m class telescopes are being operated at former four observatories. SXAO is changed as National Time Service Center. Because of city expansion as well as the traveling and economic developments, these observatories are suffered severe light pollution. For example, Zo Ce is located at the suburb of Shanghai city. A 40 cm double astrograph was installed in 1900 and a 1.56 m optical reflector have been operated since November 1987. In 1994 the seeing is better than 1 and the night sky brightness in V is about 19 mag/arcsec 2, stars fainter than 20 mag with CCD are visibles. In 2007 a large playground was built in Zô Cè area. The light pollution is severe gradually. The night sky brightness has been increased to 15.8 mag/arcsec 2. The other observatories have similar situation. New site surveys and found new stations to solve the problem. Except the solar and radio stations of each Astronomical Observatory, now there are 3 optical observing sites at PMO (Hong-He, Xu-Yi and Yaoan), 2 at SHAO (Zô Cè and Tian Huang Ping) and 2 at YNAO (Kunming and Gao-Mei-Gu) as well as 1 optical observing site at BAO (Xing-Long). The best observing site is Gao-Mei-Gu, which is selected as the optical observing site of YNAO and where atmospheric turbulence distribution is 0.11 near ground with heights from 6.5m to 2.7m during night. Sky brightness in B and V band

Final work plan : environmental site investigation at Sylvan Grove, Kansas.

Energy Technology Data Exchange (ETDEWEB)

LaFreniere, L. M. (Environmental Science Division)

2012-07-15

In 1998, carbon tetrachloride was found above the maximum contaminant level (MCL) of 5 {micro}g/L in groundwater from one private livestock well at Sylvan Grove, Kansas, by the Kansas Department of Health and Environment (KDHE). The 1998 KDHE sampling was conducted under the U.S. Department of Agriculture (USDA) private well sampling program. The Commodity Credit Corporation (CCC), a USDA agency, operated a grain storage facility in Sylvan Grove from 1954 to1966. Carbon tetrachloride is the contaminant of primary concern at sites associated with former CCC/USDA grain storage operations. Sylvan Grove is located in western Lincoln County, approximately 60 mi west of Salina (Figure 1.1). To determine whether the former CCC/USDA facility at Sylvan Grove is a potential contaminant source and its possible relationship to the contamination in groundwater, the CCC/USDA has agreed to conduct an investigation, in accordance with the Intergovernmental Agreement between the KDHE and the Farm Service Agency (FSA) of the USDA. This Work Plan presents historical data related to previous investigations, grain storage operations, local private wells and public water supply (PWS) wells, and local geologic and hydrogeologic conditions at Sylvan Grove. The findings from a review of all available documents are discussed in Section 2. On the basis of the analyses of historical data, the following specific technical objectives are proposed for the site investigation at Sylvan Grove: (1) Evaluate the potential source of carbon tetrachloride at the former CCC/USDA facility; (2) Determine the relationship of potential contamination (if present) at the former CCC/USDA facility to contamination identified in 1998 in groundwater samples from one private well to the west; and (3) Delineate the extent of potential contamination associated with the former CCC/USDA facility. The detailed scope of work is outlined in Section 3. The results of the proposed work will provide the basis for determining

Barriers and enabling factors for work-site physical activity programs: a qualitative examination.

Science.gov (United States)

Fletcher, Gena M; Behrens, Timothyh K; Domina, Lorie

2008-05-01

Work sites offer a productive setting for physical activity (PA) promoting interventions. Still, PA participation remains low. Thus, the purpose of this study was to examine the reasoning behind commonly reported barriers and enabling factors to participation in PA programs in a work-site setting. Employees from a large city government were recruited to participate in focus groups, stratified by white- and blue-collar occupations. Responses from open-ended questions about factors influencing participation in PA programs were audio recorded and transcribed verbatim. Resulting data were analyzed with open and axial coding. The sample consisted of 60 employees composing 9 focus groups. Although time was the most common barrier between both groups, white-collars workers responded that scheduling and work conflicts were the most common barrier concerning time. Blue-collar workers indicated shift work as their most common barrier. In addition, health was a significant enabling factor for both occupational categories. White-collar workers were much more concerned with appearances and were more highly motivated by weight loss and the hopefulness of quick results than were blue-collar workers. These findings are important in the understanding of PA as it relates to the reasoning behind participation in work-site programs in regard to occupational status.

Systematic evaluation of observational methods assessing biomechanical exposures at work

DEFF Research Database (Denmark)

Takala, Esa-Pekka; Pehkonen, Irmeli; Forsman, Mikael

2010-01-01

the use of technical instruments. Generally, the observations showed moderate to good agreement with the corresponding assessments made from video recordings; agreement was the best for large-scale body postures and work actions. Postures of wrist and hand as well as trunk rotation seemed to be more...... difficult to observe correctly. Intra- and inter-observer repeatability were reported for 7 and 17 methods, respectively, and were judged mostly to be good or moderate. CONCLUSIONS: With training, observers can reach consistent results on clearly visible body postures and work activities. Many observational...

Site 300 hazardous-waste-assessment project. Interim report: December 1981. Preliminary site reconnaissance and project work plan

International Nuclear Information System (INIS)

Raber, E.; Helm, D.; Carpenter, D.; Peifer, D.; Sweeney, J.

1982-01-01

This document was prepared to outline the scope and objectives of the Hazardous Waste Assessment Project (HWAP) at Site 300. This project was initiated in October, 1981, to investigate the existing solid waste landfills in an effort to satisfy regulatory guidelines and assess the potential for ground-water contamination. This involves a site-specific investigation (utilizing geology, hydrology, geophysics and geochemistry) with the goal of developing an effective ground-water quality monitoring network. Initial site reconnaissance work has begun and we report the results, to date, of our geologic hydrogeologic studies. All known solid waste disposal locations are underlain by rocks of either the Late Miocene Neroly Formation or the Cierbo Formation, both of which are dominantly sandstones interbedded with shale and claystone. The existence of a regional confined (artesian) aquifer, as well as a regional water-table aquifer is postulated for Site 300. Preliminary analysis has led to an understanding of directions and depths of regional ground-water flow

Mechanisation and automation technologies development in work at construction sites

Science.gov (United States)

Sobotka, A.; Pacewicz, K.

2017-10-01

Implementing construction work that creates buildings is a very complicated and laborious task and requires the use of various types of machines and equipment. For years there has been a desire for designers and technologists to introduce devices that replace people’s work on machine construction, automation and even robots. Technologies for building construction are still being developed and implemented to limit people’s hard work and improve work efficiency and quality in innovative architectonical and construction solutions. New opportunities for improving work on the construction site include computerisation of technological processes and construction management for projects and processes. The aim of the paper was to analyse the development of mechanisation, automation and computerisation of construction processes and selected building technologies, with special attention paid to 3D printing technology. The state of mechanisation of construction works in Poland and trends in its development in construction technologies are presented. These studies were conducted on the basis of the available literature and a survey of Polish construction companies.

Cultural Work as a Site of Struggle: Freelancers and Exploitation

Directory of Open Access Journals (Sweden)

Nicole S. Cohen

2012-05-01

Full Text Available This paper argues that Marxist political economy is a useful framework for understanding contemporary conditions of cultural work. Drawing on Karl Marx’s foundational concepts, labour process theory, and a case study of freelance writers, I argue that the debate over autonomy and control in cultural work ignores exploitation in labour-capital relationships, which is a crucial process shaping cultural work. To demonstrate the benefits of this approach, I discuss two methods media firms use to extract surplus value from freelance writers: exploitation of unpaid labour time and exploitation of intellectual property through aggressive copyright regimes. I argue that a Marxist perspective can uncover the dynamics that are transforming cultural industries and workers’ experiences. From this perspective, cultural work is understood as a site of struggle.

Does work-site physical activity improve self-reported psychosocial workplace factors and job satisfaction?

DEFF Research Database (Denmark)

Roessler, K K; Rugulies, R; Bilberg, R

2013-01-01

PURPOSE: To investigate whether a work-site strength-training program has a positive effect on self-reported psychosocial workplace factors and job satisfaction. METHODS: We conducted a randomized controlled trial among laboratory technicians implementing neck and shoulder exercises for pain relief......, with 199 participants in the training group and 228 in the control group. Influence at work, sense of community, time pressure, and job satisfaction were measured with the Copenhagen Psychosocial Questionnaire at baseline and post-intervention after 20 weeks. RESULTS: There was no statistically significant...... of a work-site strength-training program on self-reported psychosocial workplace factors and job satisfaction....

Exposure to crystalline silica at Alberta work sites: review of controls.

Science.gov (United States)

Radnoff, Diane; Todor, Maria S; Beach, Jeremy

2015-01-01

From 2009 to 2013, Alberta Jobs, Skills, Training, and Labour (JSTL) conducted a project to evaluate exposure to crystalline silica and assess controls to protect workers. Information on exposure results has been previously reported; this article discusses the data collected on workplace controls. Information on work site controls was collected during exposure assessments consisting of qualitative information on controls in place and used by workers at the time of the assessments. Where there was sufficient data, the information was further analyzed to evaluate the impact of a particular control. While many types of controls were observed, they were not always effective or in use. The control available most often was respiratory protective equipment (RPE). Generally, when respirators were used, they were correctly selected for the level of measured exposure. However, not all workers who were potentially overexposed wore respirators at the time of the assessments. When the use of respirators was taken into account, about one-third of workers were still potentially exposed over the Alberta occupational exposure limit. The industries with the highest levels of exposure tended to be those with the most unprotected workers. Issues were identified with the use of improper work practices such as dry cleaning methods, lack of documented work procedures, poor housekeeping, and lack of training which may have contributed to worker exposure levels. There is a wide range in the efficacy of controls, particularly engineering controls. Most of the literature focuses on engineering controls; however administrative controls also play a role in reducing worker exposure. Data collected in this work indicated that simple changes to work procedures and behavior (such as improved housekeeping) may be effective, low-cost ways to reduce workplace exposure. More study is required to evaluate the impact and efficacy of administrative controls such as housekeeping and training. Employers

Great Lakes Daily Ice Observations at NOAA Water Level Gauge Sites

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains daily visual ice observations taken yearly from 1 November to 30 April at NOAA/National Ocean Service water level gauge sites in the Great...

Site Characterization Work Plan for the Gnome-Coach Site, New Mexico (Rev. 1, January 2002); FINAL

International Nuclear Information System (INIS)

2002-01-01

Project Gnome was the first nuclear experiment conducted under the U.S. Atomic Energy Commission (AEC), predecessor to the U.S. Department of Energy (DOE), Plowshare Program. The Plowshare Program focused on developing nuclear devices exclusively for peaceful purposes. The intent of the Gnome experiment was to evaluate the effects of a nuclear detonation in a salt medium. Historically, Project Gnome consisted of a single detonation of a nuclear device on December 10, 1961 with the Salado Formation. Since the Gnome detonation, the AEC/DOE has conducted surface restoration, site reconnaissance, and decontamination and decommissioning activities at the site. In addition, annual groundwater sampling is performed under a long-term hydrological monitoring program begun in 1972. Coach, an experiment to be located near the Gnome project, was initially scheduled for 1963. Although construction and rehabilitation were completed for Coach, the experiment was canceled and never executed. Known collectively as Project Gnome-Coach, the site is located approximately 25 miles east of Carlsbad, New Mexico, in Eddy County, and is comprised of nearly 680 acres, of which approximately 60 acres are disturbed from the combined AEC/DOE operations. The scope of this work plan is to document the environmental objectives and the proposed technical site investigation strategies that will be utilized for the site characterization of the project. The subsurface at the Gnome-Coach site has two contaminant sources that are fundamentally different in terms of both their stratigraphic location and release mechanism. The goal of this characterization is to collect data of sufficient quantity and quality to establish current site conditions and to use the data to identify and evaluate if further action is required to protect human health and the environment and achieve permanent closure of the site. The results of these activities will be presented in a subsequent corrective action decision document

WAG 2 remedial investigation and site investigation site-specific work plan/health and safety checklist for the soil and sediment task

International Nuclear Information System (INIS)

Holt, V.L.; Burgoa, B.B.

1993-12-01

This document is a site-specific work plan/health and safety checklist (WP/HSC) for a task of the Waste Area Grouping 2 Remedial Investigation and Site Investigation (WAG 2 RI ampersand SI). Title 29 CFR Part 1910.120 requires that a health and safety program plan that includes site- and task-specific information be completed to ensure conformance with health- and safety-related requirements. To meet this requirement, the health and safety program plan for each WAG 2 RI ampersand SI field task must include (1) the general health and safety program plan for all WAG 2 RI ampersand SI field activities and (2) a WP/HSC for that particular field task. These two components, along with all applicable referenced procedures, must be kept together at the work site and distributed to field personnel as required. The general health and safety program plan is the Health and Safety Plan for the Remedial Investigation and Site Investigation of Waste Area Grouping 2 at the Oak Ridge National Laboratory, Oak Ridge, Tennessee (ORNL/ER-169). The WP/HSCs are being issued as supplements to ORNL/ER-169

Long-term observations of Boreal Toads at an ARMI apex site

Science.gov (United States)

Corn, Paul Stephen; Muths, Erin L.; Pilliod, David S.

2011-01-01

The U.S. Geological Survey’s Amphibian Research and Monitoring Initiative (ARMI) is a national project with goals to monitor the status and trends of amphibians, conduct research on causes of declines, and provide information and support to management agencies for conservation of amphibian populations. ARMI activities are organized around extensive inventories and place-based monitoring (such as collaboration with the Greater Yellowstone Inventory and Monitoring Network), and intensive population studies and research at selected locations (apex sites). One such site is an oxbow pond on the Buffalo Fork near the Black Rock Ranger Station east of Grand Teton National Park. We have been conducting mark-recapture of boreal toads (Anaxyrus boreas) at Black Rock since 2002. In concert with studies of other toad populations in the Rocky Mountains, we have documented a high rate of incidence of the chytrid fungus Batrachochytrium dendrobatidis (Bd) and a negative rate of growth of the toad population, but not the population crash or extinction observed in other populations with high prevalence of Bd. Long-term observations at other ARMI apex sites have proven invaluable for studying effects of climate change on amphibian behavior, and the Black Rock site has been upgraded with onsite recording of weather data and auditory monitoring of other amphibian species. Continued research at Black Rock will be critical for understanding the interrelated effects of climate and disease on amphibians in the Greater Yellowstone Ecosystem.

The contribution of the Volcano Observations Work Package to the implementation of the European Plate Observing System

Science.gov (United States)

Puglisi, Giuseppe

2016-04-01

The overall aim of the implementation phase of European Plate Observing System (EPOS) is to make the integrated platform operational in order to guarantee seamless access to the data provided by the European Solid Earth communities. The Volcano Observations Work Package (WP11) contributes to this objective by implementing a Thematic Core Service (TCS) which is planned to give access to the data and services provided by the European Volcano Observatories (VO) and some Volcanological Research Institutions (VRI; such as university departments, laboratories, etc.). Both types are considered as national research infrastructures (RI) which the TCS will integrate. Currently, monitoring networks on European volcanoes consist of thousands of stations or sites where volcanological parameters are continuously or periodically measured. These sites are equipped with instruments for geophysical (seismic, geodetic, gravimetric, electromagnetic), geochemical (volcanic plumes, fumaroles, groundwater, rivers, soils), environmental observations (e.g. meteorological and air quality parameters), as well as various prototypal monitoring systems (e.g. Doppler radars, ground based SAR). Across Europe several laboratories provide sample characterization (rocks, gases, isotopes, etc.), quasi-continuous analysis of space-borne data (SAR, thermal imagery, SO2 and ash), as well as high-performance computing facilities. All these RIs provide high-quality information (observations) on the current status of European volcanoes and the geodynamic background of the surrounding areas. The implementation of the Volcano Observations TCS will address technical as well as managerial issues, both considering the current heterogeneous state-of-the-art of the volcanological research infrastructures in Europe. Indeed, the current arrangement of individual VO and VRI is considered too fragmented to be considered as a unique distributed infrastructure. Therefore, the main effort in the framework of the EPOS

Site preparation and excavation works for the foundation of station main building among construction works for No. 1 unit in Kashiwazaki-Kariwa Nuclear Pwer Station

International Nuclear Information System (INIS)

Ueyama, Koreyasu

1982-01-01

Tokyo Electric Power Co., Inc., is planning the nuclear power station of final capacity 8,000 MW (7 units) in the region spread over Kashiwazaki City and Kariwa Village in Niigata Prefecture. For No. 1 unit (1100 MWe BWR), the reactor installation license was obtained in September, 1977, the site preparation and road construction started in April, 1978, and harbour construction works started in August, 1979. The construction works are now at the peak, and the overall progressing rate as of the end of June, 1982, is about 51 %. The site is a hilly region of dune along the coast of the Sea of Japan, and No. 1 unit is located in the southern part of the site. This paper reports on the outline of the project, site preparation and excavation works for the foundation of the station main building. For the site preparation and the excavation works for the foundation the main building, the shape of slope cutting, the design of landslide-preventing wall for the vertical excavation for the reactor complex building, and the construction plan and the result are reported. For underground water impermeable wall works, its outline, groundwater condition, groundwater simulation analysis, the investigation of wall installation, the wall structure and construction are described in detail. Also the outline of the control of slope face measurement, the control standards and the measured results are reported. (Wakatsuki, Y.)

Site preparation and excavation works for the foundation of station main building among construction works for No. 1 unit in Kashiwazaki-Kariwa Nuclear Power Station

Energy Technology Data Exchange (ETDEWEB)

Ueyama, Koreyasu [Tokyo Electric Power Co., Inc. (Japan)

1982-09-01

Tokyo Electric Power Co., Inc., is planning the nuclear power station of final capacity 8,000 MW (7 units) in the region spread over Kashiwazaki City and Kariwa Village in Niigata Prefecture. For No. 1 unit (1100 MWe BWR), the reactor installation license was obtained in September, 1977, the site preparation and road construction started in April, 1978, and harbour construction works started in August, 1979. The construction works are now at the peak, and the overall progressing rate as of the end of June, 1982, is about 51 %. The site is a hilly region of dune along the coast of the Sea of Japan, and No. 1 unit is located in the southern part of the site. This paper reports on the outline of the project, site preparation and excavation works for the foundation of the station main building. For the site preparation and the excavation works for the foundation the main building, the shape of slope cutting, the design of landslide-preventing wall for the vertical excavation for the reactor complex building, and the construction plan and the result are reported. For underground water impermeable wall works, its outline, groundwater condition, groundwater simulation analysis, the investigation of wall installation, the wall structure and construction are described in detail. Also the outline of the control of slope face measurement, the control standards and the measured results are reported.

Forsmark site investigation. Programme for long-term observations of geosphere and biosphere after completed site investigations

International Nuclear Information System (INIS)

2007-06-01

The site investigation at Forsmark was terminated the last of June, 2007. Hundreds of investigations have been conducted during a period of more than five years. Monitoring of a number of geoscientific parameters and biological objects has been one important part of the site investigation programme. Monitoring is defined as recurrent measurements of the same parameters/objects, so that time series are generated. Long-term monitoring of for example weather parameters, surface water discharge in brooks, and the groundwater head in a large number of boreholes has been conducted during the site investigations. Furthermore, repeated sampling of precipitation, surface water and groundwater in soil and rock for hydrochemical analyses has been carried out, and the groundwater flow in isolated borehole sections has been measured several times. Besides, some biological objects, for example rare bird species, have been invented each year of the site investigation. The measured parameters and the invented objects are characterized by a certain degree of time dependent variability, which is also site-specific. The aim of the monitoring is primarily to establish the 'undisturbed' conditions, the so called 'baseline'. If a deep repository is sited at Forsmark, many site-specific conditions will change, due to natural causes as well as to the construction works. Knowledge about the undisturbed conditions strengthens the ability to reveal and quantify such changes and to distinguish natural changes from those caused by the human activities. Another object of monitoring is to, by the study of the variability pattern of the monitored parameters, elevate the knowledge about the underlying, often complex causes governing the variations. In this way the description of site-specific conditions may be more precise and the prospects of modelling important processes are improved. After completion of the site investigations, a period of about two years will follow, when the investigation

Forsmark site investigation. Programme for long-term observations of geosphere and biosphere after completed site investigations

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-06-15

The site investigation at Forsmark was terminated the last of June, 2007. Hundreds of investigations have been conducted during a period of more than five years. Monitoring of a number of geoscientific parameters and biological objects has been one important part of the site investigation programme. Monitoring is defined as recurrent measurements of the same parameters/objects, so that time series are generated. Long-term monitoring of for example weather parameters, surface water discharge in brooks, and the groundwater head in a large number of boreholes has been conducted during the site investigations. Furthermore, repeated sampling of precipitation, surface water and groundwater in soil and rock for hydrochemical analyses has been carried out, and the groundwater flow in isolated borehole sections has been measured several times. Besides, some biological objects, for example rare bird species, have been invented each year of the site investigation. The measured parameters and the invented objects are characterized by a certain degree of time dependent variability, which is also site-specific. The aim of the monitoring is primarily to establish the 'undisturbed' conditions, the so called 'baseline'. If a deep repository is sited at Forsmark, many site-specific conditions will change, due to natural causes as well as to the construction works. Knowledge about the undisturbed conditions strengthens the ability to reveal and quantify such changes and to distinguish natural changes from those caused by the human activities. Another object of monitoring is to, by the study of the variability pattern of the monitored parameters, elevate the knowledge about the underlying, often complex causes governing the variations. In this way the description of site-specific conditions may be more precise and the prospects of modelling important processes are improved. After completion of the site investigations, a period of about two years will follow, when

Artificial coastal lagoons at solar salt-working sites: A network of habitats for specialised, protected and alien biodiversity

Science.gov (United States)

Herbert, Roger J. H.; Broderick, Lee G.; Ross, Kathryn; Moody, Chris; Cruz, Tamira; Clarke, Leo; Stillman, Richard A.

2018-04-01

There are concerns that novel structures might displace protected species, facilitate the spread of non-indigenous species, or modify native habitats. It is also predicted that ocean warming and the associated effects of climate change will significantly increase biodiversity loss within coastal regions. Resilience is to a large extent influenced by the magnitude of dispersal and level of connectivity within and between populations. Therefore it is important to investigate the distribution and ecological significance of novel and artificial habitats, the presence of protected and alien species and potential vectors of propagule dispersal. The legacy of solar salt-making in tropical and warm temperate regions is regionally extensive areas of artificial hypersaline ponds, canals and ditches. Yet the broad-scale contribution of salt-working to a network of benthic biodiversity has not been fully established. Artisanal, abandoned and historic salt-working sites were investigated along the Atlantic coast of Europe between southern England (50°N) and Andalucía, Spain (36°N). Natural lagoons are scarce along this macrotidal coast and are vulnerable to environmental change; however it is suspected that avian propagule dispersal is important in maintaining population connectivity. During bird migration periods, benthic cores were collected for infauna from 70 waterbodies across 21 salt-working sites in 5 coastal regions. Bird ringing data were used to investigate potential avian connectivity between locations. Lagoonal specialist species, some of international conservation importance, were recorded across all regions in the storage reservoirs and evaporation ponds of continental salinas, yet few non-indigenous species were observed. Potential avian propagule transport and connectivity within and between extant salt-working sites is high and these artificial habitats are likely to contribute significantly to a network of coastal lagoon biodiversity in Europe.

Observation of aftershocks of the 2003 Tokachi-Oki earthquake for estimation of local site effects

Science.gov (United States)

Yamanaka, Hiroaki; Motoki, Kentaro; Etoh, Kiminobu; Murayama, Masanari; Komaba, Nobuhiko

2004-03-01

Observation of aftershocks of the 2003 Tokachi-Oki earthquake was conducted in the southern part of the Tokachi basin in Hokkaido, Japan for estimation of local site effects. We installed accelerographs at 12 sites in Chokubetsu, Toyokoro, and Taiki areas, where large strong motion records were obtained during the main shock at stations of the K-NET and KiK-net. The stations of the aftershock observation are situated with different geological conditions and some of the sites were installed on Pleistocene layers as reference sites. The site amplifications are investigated using spectral ratio of S-waves from the aftershocks. The S-wave amplification factor is dominant at a period of about 1 second at the site near the KiK-net site in Toyokoro. This amplification fits well with calculated 1D amplification of S-wave in alluvial layers with a thickness of 50 meters. In addition to the site effects, we detected nonlinear amplification of the soft soils only during the main shock. The site effects at the strong motion site of the K-NET at Chokubetsu have a dominate peak at a period of 0.4 seconds. This amplification is due to soft soils having a thickness of about 13 meters. Contrary to the results at the two areas, site effects are not significantly different at the stations in the Taiki area, because of similarity on surface geological conditions.

Common Elements for Success: What Makes the Deal Work at Contaminated Sites

Science.gov (United States)

This page contains the presentations from the Brown to Green: Make the Connection to Renewable Energy workshop held in Santa Fe, New Mexico, during December 10-11, 2008 regarding Common Elements for Success - What makes the Deal Work at Contaminated Sites.

Students' Participation in Social Networking Sites: Implications for Social Work Education

Science.gov (United States)

Mukherjee, Dhrubodhi; Clark, Janet

2012-01-01

Social work students have few guidelines to help them evaluate the implication of their posted information on Internet-based social networking sites (SNSs). There is a national trend among employers of human services to cross-check publicly available online information on applicants. Based on data from a survey of 105 baccalaureate and master's…

Deriving surface soil moisture from reflected GNSS signal observations from a grassland site in southwestern France

Science.gov (United States)

Zhang, Sibo; Calvet, Jean-Christophe; Darrozes, José; Roussel, Nicolas; Frappart, Frédéric; Bouhours, Gilles

2018-03-01

This work assesses the estimation of surface volumetric soil moisture (VSM) using the global navigation satellite system interferometric reflectometry (GNSS-IR) technique. Year-round observations were acquired from a grassland site in southwestern France using an antenna consecutively placed at two contrasting heights above the ground surface (3.3 and 29.4 m). The VSM retrievals are compared with two independent reference datasets: in situ observations of soil moisture, and numerical simulations of soil moisture and vegetation biomass from the ISBA (Interactions between Soil, Biosphere and Atmosphere) land surface model. Scaled VSM estimates can be retrieved throughout the year removing vegetation effects by the separation of growth and senescence periods and by the filtering of the GNSS-IR observations that are most affected by vegetation. Antenna height has no significant impact on the quality of VSM estimates. Comparisons between the VSM GNSS-IR retrievals and the in situ VSM observations at a depth of 5 cm show good agreement (R2 = 0.86 and RMSE = 0.04 m3 m-3). It is shown that the signal is sensitive to the grass litter water content and that this effect triggers differences between VSM retrievals and in situ VSM observations at depths of 1 and 5 cm, especially during light rainfall events.

Comparing the Scoring of Human Decomposition from Digital Images to Scoring Using On-site Observations.

Science.gov (United States)

Dabbs, Gretchen R; Bytheway, Joan A; Connor, Melissa

2017-09-01

When in forensic casework or empirical research in-person assessment of human decomposition is not possible, the sensible substitution is color photographic images. To date, no research has confirmed the utility of color photographic images as a proxy for in situ observation of the level of decomposition. Sixteen observers scored photographs of 13 human cadavers in varying decomposition stages (PMI 2-186 days) using the Total Body Score system (total n = 929 observations). The on-site TBS was compared with recorded observations from digital color images using a paired samples t-test. The average difference between on-site and photographic observations was -0.20 (t = -1.679, df = 928, p = 0.094). Individually, only two observers, both students with human decomposition based on digital images can be substituted for assessments based on observation of the corpse in situ, when necessary. © 2017 American Academy of Forensic Sciences.

A suggested color scheme for reducing perception-related accidents on construction work sites.

Science.gov (United States)

Yi, June-seong; Kim, Yong-woo; Kim, Ki-aeng; Koo, Bonsang

2012-09-01

Changes in workforce demographics have led to the need for more sophisticated approaches to addressing the safety requirements of the construction industry. Despite extensive research in other industry domains, the construction industry has been passive in exploring the impact of a color scheme; perception-related accidents have been effectively diminished by its implementation. The research demonstrated that the use of appropriate color schemes could improve the actions and psychology of workers on site, thereby increasing their perceptions of potentially dangerous situations. As a preliminary study, the objects selected by rigorous analysis on accident reports were workwear, safety net, gondola, scaffolding, and safety passage. The colors modified on site for temporary facilities were adopted from existing theoretical and empirical research that suggests the use of certain colors and their combinations to improve visibility and conspicuity while minimizing work fatigue. The color schemes were also tested and confirmed through two workshops with workers and managers currently involved in actual projects. The impacts of color schemes suggested in this paper are summarized as follows. First, the color schemes improve the conspicuity of facilities with other on site components, enabling workers to quickly discern and orient themselves in their work environment. Secondly, the color schemes have been selected to minimize the visual work fatigue and monotony that can potentially increase accidents. Copyright © 2011 Elsevier Ltd. All rights reserved.

Spirit's Winter Work Site

Science.gov (United States)

2006-01-01

[figure removed for brevity, see original site] Annotated Version This portion of an image acquired by the Mars Reconnaissance Orbiter's High Resolution Imaging Science Experiment camera shows the Spirit rover's winter campaign site. Spirit was parked on a slope tilted 11 degrees to the north to maximize sunlight during the southern winter season. 'Tyrone' is an area where the rover's wheels disturbed light-toned soils. Remote sensing and in-situ analyses found the light-toned soil at Tyrone to be sulfate rich and hydrated. The original picture is catalogued as PSP_001513_1655_red and was taken on Sept. 29, 2006. NASA's Jet Propulsion Laboratory, a division of the California Institute of Technology in Pasadena, manages the Mars Reconnaissance Orbiter for NASA's Science Mission Directorate, Washington. Lockheed Martin Space Systems, Denver, is the prime contractor for the project and built the spacecraft. The High Resolution Imaging Science Experiment is operated by the University of Arizona, Tucson, and the instrument was built by Ball Aerospace and Technology Corp., Boulder, Colo.

CERCLA site assessment workbook

International Nuclear Information System (INIS)

1994-08-01

This contains comments for each chapter of exercises (in Vol. 1) which illustrate how to conduct site assessments for CERCLA regulation. A through analysis of the exercises is provided so that work and solutions from Vol 1 can be critiqued and comments are also included on the strategy of site assessment whereas the exercises illustrate the principles involved. Covered exercises include the following: A preliminary assessment of a ground water site; waste characteristics and characterization of sources; documentation of observed releases and actual contamination of targets; the strategy of an SI at a surface water site; the soil exposure pathway; the air pathway

Work plan for the radiological survey for the David Witherspoon, Incorporated, Landfill-1630 site, Knoxville, Tennessee

International Nuclear Information System (INIS)

1996-07-01

This work plan establishes the methods and requirements for performing a radiological survey at the David Witherspoon, Incorporated, Landfill-1630 Site, Knoxville, Tennessee (DWI 1630 Site) in accordance with requirements under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). The radiological survey will identify the radiological contamination level of the equipment and debris stored at the DWI 1630 Site. The data generated from the survey activities will support the decisions for characterization of the equipment/debris and aid in subsequent disposition and waste handling. The survey activities to be performed under this work plan include an equipment radiological survey, a walkover survey, and an immunoassay testing for polychlorinated biphenyls (PCBs). This work plan includes a quality assurance (QA)/quality control (QC) project plan, a health and safety (H ampersand S) plan, and a waste management plan

Behavioural changes experienced by contract managers while working on remote project sites

OpenAIRE

2012-01-01

M.B.A. This research project is concerned with the behavioural changes of contract managers while working on 'remote' project sites. While working on such a project, the researcher became aware that the behaviour of certain contract managers changed over the course of the project, and that this behaviour was not the same as they demonstrated when at home or in the office environment. In many instances these behavioural changes were of a negative nature, the consequences of which often resu...

MGP site remediation: Working toward presumptive remedies

International Nuclear Information System (INIS)

Larsen, B.R.

1996-01-01

Manufactured Gas Plants (MGPs) were prevalent in the United States during the 19th and first half of the 20th centuries. MGPs produced large quantities of waste by-products, which varied depending on the process used to manufacture the gas, but most commonly were tars and polynuclear aromatic hydrocarbons. There are an estimated 3,000 to 5,000 abandoned MGP sites across the United States. Because these sites are not concentrated in one geographic location and at least three different manufacturing processes were used, the waste characteristics are very heterogeneous. The question of site remediation becomes how to implement a cost-effective remediation with the variety of cleanup technologies available for these sites. Because of the significant expenditure required for characterization and cleanup of MGP sites, owners and regulatory agencies are beginning to look at standardizing cleanup technologies for these sites. This paper discusses applicable cleanup technologies and the attitude of state regulatory agencies towards the use of presumptive remedies, which can reduce the amount of characterization and detailed analysis necessary for any particular site. Additionally, this paper outlines the process of screening and evaluating candidate technologies, and the progress being made to match the technology to the site

Work plan for the remedial investigation/feasibility study-environmental assessment for the Colonie site, Colonie, New York

International Nuclear Information System (INIS)

1990-06-01

This work plan has been prepared to document the scoping and planning process performed by the US Department of Energy (DOE) to support remedial action activities at the Colonie site. The site is located in eastern New York State in the town of Colonie near the city of Albany. Remedial action of the Colonie site is being planned as part of DOE's Formerly Utilized Sites Remedial Action Program. The DOE is responsible for controlling the release of all radioactive and chemical contaminants from the site. Under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), a remedial investigation/feasibility study (RI/FS) must be prepared to support the decision-making process for evaluating remedial action alternatives. This work plan contains a summary of information known about the site as of January 1988, presents a conceptual site model that identifies potential routes of human exposure to site containments, identifies data gaps, and summarizes the process and proposed studies that will be used to fill the data gaps. In addition, DOE activities must be conducted in compliance with the National Environmental Policy Act (NEPA), which requires consideration of the environmental consequences of a proposed action as part of its decision-making process. This work also describes the approach that will be used to evaluate potential remedial action alternatives and includes a description of the organization, project controls, and task schedules that will be employed to fulfill the requirements of both CERCLA and NEPA. 48 refs., 18 figs., 25 tabs

US DOE-EM On-Site Disposal Cell Working Group - Fostering Communication On Performance Assessment Challenges

Energy Technology Data Exchange (ETDEWEB)

Seitz, Roger R. [Savannah River Site (SRS), Aiken, SC (United States); Suttora, Linda C. [U.S. Department of Energy, Office of Site Restoration, Germantown, MD (United States); Phifer, Mark [Savannah River Site (SRS), Aiken, SC (United States)

2014-03-01

On-site disposal cells are in use and being considered at several U.S. Department of Energy (USDOE) sites as the final disposition for large amounts of waste associated with cleanup of contaminated areas and facilities. These facilities are typically developed with regulatory oversight from States and/or the US Environmental Protection Agency (USEPA) in addition to USDOE. The facilities are developed to meet design standards for disposal of hazardous waste as well as the USDOE performance based standards for disposal of radioactive waste. The involvement of multiple and different regulators for facilities across separate sites has resulted in some differences in expectations for performance assessments and risk assessments (PA/RA) that are developed for the disposal facilities. The USDOE-EM Office of Site Restoration formed a working group to foster improved communication and sharing of information for personnel associated with these Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) disposal cells and work towards more consistent assumptions, as appropriate, for technical and policy considerations related to performance and risk assessments in support of a Record of Decision and Disposal Authorization Statement. The working group holds teleconferences, as needed, focusing on specific topics of interest. The topics addressed to date include an assessment of the assumptions used for performance assessments and risk assessments (PA/RAs) for on-site disposal cells, requirements and assumptions related to assessment of inadvertent intrusion, DOE Manual 435.1-1 requirements, and approaches for consideration of the long-term performance of liners and covers in the context of PAs. The working group has improved communication among the staff and oversight personnel responsible for onsite disposal cells and has provided a forum to identify and resolve common concerns.

Deriving surface soil moisture from reflected GNSS signal observations from a grassland site in southwestern France

Directory of Open Access Journals (Sweden)

S. Zhang

2018-03-01

Full Text Available This work assesses the estimation of surface volumetric soil moisture (VSM using the global navigation satellite system interferometric reflectometry (GNSS-IR technique. Year-round observations were acquired from a grassland site in southwestern France using an antenna consecutively placed at two contrasting heights above the ground surface (3.3 and 29.4 m. The VSM retrievals are compared with two independent reference datasets: in situ observations of soil moisture, and numerical simulations of soil moisture and vegetation biomass from the ISBA (Interactions between Soil, Biosphere and Atmosphere land surface model. Scaled VSM estimates can be retrieved throughout the year removing vegetation effects by the separation of growth and senescence periods and by the filtering of the GNSS-IR observations that are most affected by vegetation. Antenna height has no significant impact on the quality of VSM estimates. Comparisons between the VSM GNSS-IR retrievals and the in situ VSM observations at a depth of 5 cm show good agreement (R2 =  0.86 and RMSE  =  0.04 m3 m−3. It is shown that the signal is sensitive to the grass litter water content and that this effect triggers differences between VSM retrievals and in situ VSM observations at depths of 1 and 5 cm, especially during light rainfall events.

Great Lakes Daily Ice Observations at NOAA Water Level Gauge Sites, Version 1

Data.gov (United States)

National Aeronautics and Space Administration — This data set contains daily visual ice observations taken yearly from 1 November to 30 April at NOAA/National Ocean Service water level gauge sites in the Great...

Site systems engineering fiscal year 1999 multi-year work plan (MYWP) update for WBS 1.8.2.2; TOPICAL

International Nuclear Information System (INIS)

GRYGIEL, M.L.

1998-01-01

Manage the Site Systems Engineering process to provide a traceable integrated requirements-driven, and technically defensible baseline. Through the Site Integration Group(SIG), Systems Engineering ensures integration of technical activities across all site projects. Systems Engineering's primary interfaces are with the RL Project Managers, the Project Direction Office and with the Project Major Subcontractors, as well as with the Site Planning organization. Systems Implementation: (1) Develops, maintains, and controls the site integrated technical baseline, ensures the Systems Engineering interfaces between projects are documented, and maintain the Site Environmental Management Specification. (2) Develops and uses dynamic simulation models for verification of the baseline and analysis of alternatives. (3) Performs and documents fictional and requirements analyses. (4) Works with projects, technology management, and the SIG to identify and resolve technical issues. (5) Supports technical baseline information for the planning and budgeting of the Accelerated Cleanup Plan, Multi-Year Work Plans, Project Baseline Summaries as well as performance measure reporting. (6) Works with projects to ensure the quality of data in the technical baseline. (7) Develops, maintains and implements the site configuration management system

Civil Engineering Works Status of the Proton Accelerator Research Center in PEFP - Site and Access Road Earthwork

International Nuclear Information System (INIS)

Nam, Jung Min; Jeon, G. P.; Min, Y. S.; Park, S. S.; Cho, J. S.; Mun, K. J.; Kim, J. Y.

2010-01-01

PEFP(Proton Engineering Frontier Project) was Launched in 2002 as one of the 21st Century Frontier R and D Programs of MOST(Ministry of Science and Technology). Gyeongju city was selected as the project host site in March, 2006, where 'Proton Accelerator Research Center' was going to be constructed. Since 2005, the Architectural and Civil design work has been performing. The Earthwork of the site was started in June, 2009. In this paper, we describe the status of the civil engineering works for the PEFP, focusing on the earthwork of the site and access road

Hanford Site Environmental Restoration Program 1994 fiscal year work plan

International Nuclear Information System (INIS)

1993-01-01

Site Management System (SMS) guidance requires a Fiscal Year Work Plan (FYWP) to be prepared for the Environmental Restoration (ER) Mission Area and all related programs. This revision is a complete update to cover the FY 1994 time period. This document describes the overall ER Missions Area and provides FYWP appendices for each of the following five program areas: Remedial Action (RA); Decontamination and Decommissioning (D ampersand D); Project Management and Support (PM ampersand S); Surveillance and Maintenance (S ampersand M); and Disposal Facilities (DF)

An Ideal Observer Analysis of Visual Working Memory

Science.gov (United States)

Sims, Chris R.; Jacobs, Robert A.; Knill, David C.

2012-01-01

Limits in visual working memory (VWM) strongly constrain human performance across many tasks. However, the nature of these limits is not well understood. In this article we develop an ideal observer analysis of human VWM by deriving the expected behavior of an optimally performing but limited-capacity memory system. This analysis is framed around…

First excavation work on Meyrin site

CERN Document Server

1954-01-01

Geneva was selected as the site for the CERN Laboratory at the third session of the provisional Council in 1952. This selection successfully passed a referendum in the canton of Geneva in June 1953 by 16539 votes to 7332. On 17 May 1954, the first shovel of earth was dug on the Meyrin site under the eyes of Geneva officials and members of CERN staff

The CarboCount CH sites: characterization of a dense greenhouse gas observation network

Directory of Open Access Journals (Sweden)

B. Oney

2015-10-01

Full Text Available We describe a new rural network of four densely placed (2, CH4, and CO measurement sites in north-central Switzerland and analyze its suitability for regional-scale (~ 100–500 km carbon flux studies. We characterize each site for the period from March 2013 to February 2014 by analyzing surrounding land cover, observed local meteorology, and sensitivity to surface fluxes, as simulated with the Lagrangian particle dispersion model FLEXPART-COSMO (FLEXible PARTicle dispersion model-Consortium for Small-Scale Modeling. The Beromünster measurements are made on a tall tower (212 m located on a gentle hill. At Beromünster, regional CO2 signals (measurement minus background vary diurnally from −4 to +4 ppmv, on average, and are simulated to come from nearly the entire Swiss Plateau, where 50 % of surface influence is simulated to be within 130–260 km distance. The Früebüel site measurements are made 4 m above ground on the flank of a gently sloping mountain. Nearby (2 signals varying diurnally from −5 to +12 ppmv and elevated summer daytime CH4 signals (+30 ppbv above other sites. The Gimmiz site measurements are made on a small tower (32 m in flat terrain. Here, strong summertime regional signals (−5 to +60 ppmv CO2 stem from large, nearby (2. Here, considerable anthropogenic influence from the nearby industrialized region near Zurich causes the average wintertime regional CO2 signals to be 5 ppmv above the regional signals simultaneously measured at the Früebüel site. We find that the suitability of the data sets from our current observation network for regional carbon budgeting studies largely depends on the ability of the high-resolution (2 km atmospheric transport model to correctly capture the temporal dynamics of the stratification of the lower atmosphere at the different sites. The current version of the atmospheric transport model captures these dynamics well, but it clearly reaches its limits at the sites in steep topography

Site Characterization Work Plan for Gasbuggy, New Mexico (Rev.1, Jan. 2002)

Energy Technology Data Exchange (ETDEWEB)

U.S. Department of Energy, National Nuclear Security Administration Nevada Operations Office (NNSA/NV)

2002-01-25

Project Gasbuggy was the first of three joint government-industry experiments conducted to test the effectiveness of nuclear explosives to fracture deeply buried, low-permeability natural gas reservoirs to stimulate production. The scope of this work plan is to document the environmental objectives and the proposed technical site investigation strategies that will be utilized for the site characterization of the Project Gasbuggy Site. Its goal is the collection of data in sufficient quantity and quality to determine current site conditions, support a risk assessment for the site surfaces, and evaluate if further remedial action is required to achieve permanent closure of the site that is both protective of human health and the environment. The Gasbuggy Site is located approximately 55 air miles east of Farmington, New Mexico, in Rio Arriba County within the Carson National Forest in the northeast portion of the San Juan Basin. Historically, Project Gasbuggy consisted of the joint government-industry detonation of a nuclear device on December 10, 1967, followed by reentry drilling and gas production testing and project evaluation activities in post-detonation operations from 1967 to 1976. Based on historical documentation, no chemical release sites other than the mud pits were identified; additionally, there was no material buried at the Gasbuggy Site other than drilling fluids and construction debris. Although previous characterization and restoration activities including sensitive species surveys, cultural resources surveys, surface geophysical surveys, and limited soil sampling and analysis were performed in 1978 and again in 2000, no formal closure of the site was achieved. Also, these efforts did not adequately address the site's potential for chemical contamination at the surface/shallow subsurface ground levels or the subsurface hazards for potential migration outside of the current site subsurface intrusion restrictions. Additional investigation

The Hanford Site Environmental Restoration Program 1993 fiscal year work plan

International Nuclear Information System (INIS)

1992-09-01

Site Management System (SMS) guidance requires a Fiscal Year Work Plan (FYWP) be prepared for the Environmental Restoration (ER) Mission Area and all related programs. This document describes the overall ER Mission Area and provides FYWP appendixes for each of the five program areas: Remedial Action (RA); Decontamination and Decommissioning (D ampersand D); Project Management and Support (PM ampersand S); Surveillance and Maintenance (S ampersand M); and Treatment, Storage, and/or Disposal (TSD)

78 FR 32462 - Wyatt Virgin Islands (V.I.), Inc., a Division of Wyatt Field Service Company, Working On-Site at...

Science.gov (United States)

2013-05-30

... the subject worker group was established to exclusively work at the HOVENSA refinery plant in the U.S....), Inc., a Division of Wyatt Field Service Company, Working On-Site at Hovensa, LLC Oil Refinery... (V.I.), Inc., a division of Wyatt Field Service Company, working on-site at HOVENSA, LLC Oil Refinery...

30 CFR 71.500 - Sanitary toilet facilities at surface work sites; installation requirements.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Sanitary toilet facilities at surface work sites; installation requirements. 71.500 Section 71.500 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-SURFACE COAL MINES AND...

A work-site weight control program using financial incentives collected through payroll deduction.

Science.gov (United States)

Forster, J L; Jeffery, R W; Sullivan, S; Snell, M K

1985-11-01

In a work-site weight control program using a self-motivational program of financial incentives implemented through payroll deduction, 131 university employees chose weight loss goals (0 to 60 lb) and incentives (+5 to +30) to be deducted from each paycheck for six months. Return of incentive money was contingent on progress toward weight goals. Participants were assigned randomly to one of four protocols, involving group educational sessions v self-instruction only and required v optional attendance at weigh-ins and sessions. Overall, dropout rates (21.4%) and mean weight loss (12.2 lb) were encouraging, especially compared with those of other work-site programs. Weight loss was positively associated with attendance at weigh-ins and educational sessions. However, requiring attendance did not increase program effectiveness and seemed also to discourage enrollment among men. The weight control program was equally effective when offered with professionally led educational sessions or when accompanied by self-instructional materials only.

Work characteristics predict the development of multi-site musculoskeletal pain.

Science.gov (United States)

Oakman, Jodi; de Wind, Astrid; van den Heuvel, Swenne G; van der Beek, Allard J

2017-10-01

Musculoskeletal pain in more than one body region is common and a barrier to sustaining employment. We aimed to examine whether work characteristics predict the development of multi-site pain (MSP), and to determine differences in work-related predictors between age groups. This study is based on 5136 employees from the Study on Transitions in Employment, Ability and Motivation (STREAM) who reported no MSP at baseline. Measures included physical, emotional, mental, and psychological job demands, social support and autonomy. Predictors of MSP were studied by logistic regression analyses. Univariate and multivariate analyses with age stratification (45-49, 50-54, 55-59, and 60-64 years) were done to explore differences between age groups. All work characteristics with the exception of autonomy were predictive of the development of MSP, with odds ratios varying from 1.21 (95% CI 1.04-1.40) for mental job demands to 1.63 (95% CI 1.43-1.86) for physical job demands. No clear pattern of age-related differences in the predictors of MSP emerged, with the exception of social support, which was predictive of MSP developing in all age groups except for the age group 60-64 years. Adverse physical and psychosocial work characteristics are associated with MSP. Organisations need to comprehensively assess work environments to ensure that all relevant workplace hazards, physical and psychosocial, are identified and then controlled for across all age groups.

WAG 2 remedial investigation and site investigation site-specific work plan/health and safety checklist for the sediment transport modeling task

International Nuclear Information System (INIS)

Holt, V.L.; Baron, L.A.

1994-05-01

This site-specific Work Plan/Health and Safety Checklist (WP/HSC) is a supplement to the general health and safety plan (HASP) for Waste Area Grouping (WAG) 2 remedial investigation and site investigation (WAG 2 RI ampersand SI) activities [Health and Safety Plan for the Remedial Investigation and Site Investigation of Waste Area Grouping 2 at the Oak Ridge National Laboratory, Oak Ridge, Tennessee (ORNL/ER-169)] and provides specific details and requirements for the WAG 2 RI ampersand SI Sediment Transport Modeling Task. This WP/HSC identifies specific site operations, site hazards, and any recommendations by Oak Ridge National Laboratory (ORNL) health and safety organizations [i.e., Industrial Hygiene (IH), Health Physics (HP), and/or Industrial Safety] that would contribute to the safe completion of the WAG 2 RI ampersand SI. Together, the general HASP for the WAG 2 RI ampersand SI (ORNL/ER-169) and the completed site-specific WP/HSC meet the health and safety planning requirements specified by 29 CFR 1910.120 and the ORNL Hazardous Waste Operations and Emergency Response (HAZWOPER) Program Manual. In addition to the health and safety information provided in the general HASP for the WAG 2 RI ampersand SI, details concerning the site-specific task are elaborated in this site-specific WP/HSC, and both documents, as well as all pertinent procedures referenced therein, will be reviewed by all field personnel prior to beginning operations

Danish Observational Study of Eldercare work and musculoskeletal disorderS (DOSES)

DEFF Research Database (Denmark)

Karstad, Kristina; Jørgensen, Anette F B; Greiner, Birgit A

2018-01-01

PURPOSE: Musculoskeletal disorders (MSDs), sickness absence and premature retirement are highly prevalent among eldercare workers. We conducted a prospective observational workplace study with the main purpose to investigate longitudinal associations between physical and psychosocial working cond...... and team factors for distribution of physical work demands and development of MSD among the workers. This will provide important knowledge for future workplace interventions to reduce MSD and sickness absence.......PURPOSE: Musculoskeletal disorders (MSDs), sickness absence and premature retirement are highly prevalent among eldercare workers. We conducted a prospective observational workplace study with the main purpose to investigate longitudinal associations between physical and psychosocial working...... conditions and occurrence of MSD and its consequences (pain-related interference with daily work activities and sickness absence) among Danish eldercare workers. PARTICIPANTS: At 20 Danish nursing homes, a total of 941 eldercare workers employed in day and evening shifts were invited to the study. Of those...

Design, application and testing of the Work Observation Method by Activity Timing (WOMBAT) to measure clinicians' patterns of work and communication.

Science.gov (United States)

Westbrook, Johanna I; Ampt, Amanda

2009-04-01

Evidence regarding how health information technologies influence clinicians' patterns of work and support efficient practices is limited. Traditional paper-based data collection methods are unable to capture clinical work complexity and communication patterns. The use of electronic data collection tools for such studies is emerging yet is rarely assessed for reliability or validity. Our aim was to design, apply and test an observational method which incorporated the use of an electronic data collection tool for work measurement studies which would allow efficient, accurate and reliable data collection, and capture greater degrees of work complexity than current approaches. We developed an observational method and software for personal digital assistants (PDAs) which captures multiple dimensions of clinicians' work tasks, namely what task, with whom, and with what; tasks conducted in parallel (multi-tasking); interruptions and task duration. During field-testing over 7 months across four hospital wards, fifty-two nurses were observed for 250 h. Inter-rater reliability was tested and validity was measured by (i) assessing whether observational data reflected known differences in clinical role work tasks and (ii) by comparing observational data with participants' estimates of their task time distribution. Observers took 15-20 h of training to master the method and data collection process. Only 1% of tasks observed did not match the classification developed and were classified as 'other'. Inter-rater reliability scores of observers were maintained at over 85%. The results discriminated between the work patterns of enrolled and registered nurses consistent with differences in their roles. Survey data (n=27) revealed consistent ratings of tasks by nurses, and their rankings of most to least time-consuming tasks were significantly correlated with those derived from the observational data. Over 40% of nurses' time was spent in direct care or professional communication

Human Health and Ecological Risk Assessment Work Plan Mud Pit Release Sites, Amchitka Island, Alaska

Energy Technology Data Exchange (ETDEWEB)

DOE/NV

2001-03-12

This Work Plan describes the approach that will be used to conduct human health and ecological risk assessments for Amchitka Island, Alaska, which was utilized as an underground nuclear test site between 1965 and 1971. During this period, the U.S. Atomic Energy Commission (now the U.S. Department of Energy) conducted two nuclear tests (known as Long Shot and Milrow) and assisted the U.S. Department of Defense with a third test (known as Cannikin). Amchitka Island is approximately 42 miles long and located 1,340 miles west-southwest of Anchorage, Alaska, in the western end of the Aleutian Island archipelago in a group of islands known as the Rat Islands. Historically including deep drilling operations required large volumes of drilling mud, a considerable amount of which was left on the island in exposed mud pits after testing was completed. Therefore, there is a need for drilling mud pit remediation and risk assessment of historical mud pit releases. The scope of this work plan is to document the environmental objectives and the proposed technical site investigation strategies that will be utilized for the site characterization of the constituents in soil, surface water, and sediment at these former testing sites. Its goal is the collection of data in sufficient quantity and quality to determine current site conditions, support a risk assessment for the site surfaces, and evaluate what further remedial action is required to achieve permanent closure of these three sites that will protect both human health and the environment. Suspected compounds of potential ecological concern for investigative analysis at these sites include diesel-range organics, polyaromatic hydrocarbons, polychlorinated biphenyls, volatile organic compounds, and chromium. The results of these characterizations and risk assessments will be used to evaluate corrective action alternatives to include no further action, the implementation of institutional controls, capping on site, or off-sit e

Energy infrastructure of the United States and projected siting needs: Scoping ideas, identifying issues and options. Draft report of the Department of Energy Working Group on Energy Facility Siting to the Secretary

Energy Technology Data Exchange (ETDEWEB)

1993-12-01

A Department of Energy (DOE) Working Group on Energy Facility Siting, chaired by the Policy Office with membership from the major program and staff offices of the Department, reviewed data regarding energy service needs, infrastructure requirements, and constraints to siting. The Working Group found that the expeditious siting of energy facilities has important economic, energy, and environmental implications for key Administration priorities.

Infrasonic observations of large-scale HE events

Science.gov (United States)

Whitaker, Rodney W.; Mutschlecner, J. Paul; Davidson, Masha B.; Noel, Susan D.

1990-01-01

The Los Alamos Infrasound Program has been operating since about mid-1982, making routine measurements of low frequency atmospheric acoustic propagation. Generally, the authors work between 0.1 Hz to 10 Hz; however, much of the work is concerned with the narrower range of 0.5 to 5.0 Hz. Two permanent stations, St. George, UT, and Los Alamos, NM, have been operational since 1983, collecting data 24 hours a day. For the purposes of this discussion, the authors concentrate on their measurements of large, high explosive (HE) events at ranges of 250 km to 5330 km. Because their equipment is well suited for mobile deployments, they can easily establish temporary observing sites for special events. The measurements are from the permanent sites, as well as from various temporary sites. A few observations that are typical of the full data set are given.

Integration of Nevada Test Site (NTS) Work Control Programs and Incorporating Integrated Safety Management (ISM) into Activity Level Work Planning and Control

International Nuclear Information System (INIS)

Kinney, Mike; Breen, Kevin

2008-01-01

This session will examine a method developed by Federal and Contractor personnel at the Nevada Site Office (NSO) to improve the planning and execution of work activities utilizing an Activity Level Work Control process in response to Defense Nuclear Facilities Safety Board (DNFSB) Recommendation 2004-1, Oversight of Complex, High-Hazard Nuclear Operations. The process was initially developed during Fiscal Year (FY) 2007, and implementation is commencing during the fourth quarter of FY 2008. This process will significantly enhance the flexibility and the appropriate rigor in the performance of work activities

Meteorologically-adjusted trend analysis of surface observed ozone at three monitoring sites in Delhi, India: 2007-2011

Science.gov (United States)

Biswas, J.; Farooqui, Z.; Guttikunda, S. K.

2012-12-01

It is well known that meteorological parameters have significant impact on surface ozone concentrations. Therefore it is important to remove the effects of meteorology on ozone concentrations to correctly estimate long-term trends in ozone levels due to the alterations in precursor emissions. This is important for the development of effectual control strategies. In this study surface observed ozone trends in New Delhi are analyzed using Komogorov-Zurbenko (KZ) filter, US EPA ozone adjustment due to weather approach and the classification and regression tree method. The statistical models are applied to the ozone data at three observational sites in New Delhi metropolitan areas, 1) Income Tax Office (ITO) 2) Sirifort and 3) Delhi College of Engineering (DCE). The ITO site is located adjacent to a traffic crossing, Sirifort is an urban site and the DCE site is located in a residential area. The ITO site is also influenced by local industrial emissions. DCE has higher ozone levels than the other two sites. It was found that ITO has lowest ozone concentrations amongst the three sites due to ozone titrating due to industrial and on-road mobile NOx emissions. The statistical methods employed can assess ozone trends at these sites with a high degree of confidence and the results can be used to gauge the effectiveness of control strategies on surface ozone levels in New Delhi.

Inter-rater reliability of direct observations of the physical and psychosocial working conditions in eldercare

DEFF Research Database (Denmark)

Karstad, Kristina; Rugulies, Reiner; Skotte, Jørgen

2018-01-01

The aim of the study was to develop and evaluate the reliability of the "Danish observational study of eldercare work and musculoskeletal disorders" (DOSES) observation instrument to assess physical and psychosocial risk factors for musculoskeletal disorders (MSD) in eldercare work. During 1.5 ye...... is appropriate for assessing physical and psychosocial risk factors for MSD among eldercare workers.......The aim of the study was to develop and evaluate the reliability of the "Danish observational study of eldercare work and musculoskeletal disorders" (DOSES) observation instrument to assess physical and psychosocial risk factors for musculoskeletal disorders (MSD) in eldercare work. During 1...

Photometric Observations of Soils and Rocks at the Mars Exploration Rover Landing Sites

Science.gov (United States)

Johnson, J. R.; Arvidson, R. A.; Bell, J. F., III; Farrand, W.; Guinness, E.; Johnson, M.; Herkenhoff, K. E.; Lemmon, M.; Morris, R. V.; Seelos, F., IV

2005-01-01

The Panoramic Cameras (Pancam) on the Spirit and Opportunity Mars Exploration Rovers have acquired multispectral reflectance observations of rocks and soils at different incidence, emission, and phase angles that will be used for photometric modeling of surface materials. Phase angle coverage at both sites extends from approx. 0 deg. to approx. 155 deg.

Atmospheric mercury concentrations observed at ground-based monitoring sites globally distributed in the framework of the GMOS network

Directory of Open Access Journals (Sweden)

F. Sprovieri

2016-09-01

Full Text Available Long-term monitoring of data of ambient mercury (Hg on a global scale to assess its emission, transport, atmospheric chemistry, and deposition processes is vital to understanding the impact of Hg pollution on the environment. The Global Mercury Observation System (GMOS project was funded by the European Commission (http://www.gmos.eu and started in November 2010 with the overall goal to develop a coordinated global observing system to monitor Hg on a global scale, including a large network of ground-based monitoring stations, ad hoc periodic oceanographic cruises and measurement flights in the lower and upper troposphere as well as in the lower stratosphere. To date, more than 40 ground-based monitoring sites constitute the global network covering many regions where little to no observational data were available before GMOS. This work presents atmospheric Hg concentrations recorded worldwide in the framework of the GMOS project (2010–2015, analyzing Hg measurement results in terms of temporal trends, seasonality and comparability within the network. Major findings highlighted in this paper include a clear gradient of Hg concentrations between the Northern and Southern hemispheres, confirming that the gradient observed is mostly driven by local and regional sources, which can be anthropogenic, natural or a combination of both.

Robust remediation strategies at gas-work sites: a case of source recognition and source characterization

International Nuclear Information System (INIS)

Vries, P.O. de

2005-01-01

In The Netherlands there have been gasworks at about 260 to 270 locations. Most of these locations are or were heavily polluted with tar, ashes and cyanides and many of them belong to the locations where remediation actions have already been executed. It seems however that many of them also belong to the locations where remediation actions were not quite as successful as was expected. So, for many gas-work sites that were already 'remedied' in the 80's and early 90's of the foregoing century, new programs for site remediation are planned. Of course the mistakes from the past should now be avoided. The current remediation strategy in The Netherlands for gas-work sites can be comprised in four steps: 1 - removing spots in the top soil, 2 - removing spots with mobile components in the shallow subsoil, 3 - controlling spots with mobile components in the deep subsoil, 4 - creating a 'steady endpoint situation' in the plume. At many former gas-work sites real sources, i.e. in a physico-chemical sense, are not very well known. This can easily lead to insufficient removal of some or part of these sources and cause a longer delivery of contaminants to the groundwater plume, with higher endpoint concentrations, higher costs and more restrictions for future use. The higher concentrations and longer deliveries originating from not recognized or not localized sources are often not sufficiently compensated by the proposed plume management in current remediation strategies. Remediation results can be improved by using knowledge about the processes that determine the delivery of contaminants to the groundwater, the materials that cause these delivery and the locations at the site where these are most likely found. When sources are present in the deep subsoil or the exact localization of sources is uncertain, robust remediation strategies should be chosen and wishful thinking about removing sources with in situ techniques should be avoided. Robust strategies are probably less

Observing Pair-Work Task in an English Speaking Class

Science.gov (United States)

Achmad, Diana; Yusuf, Yunisrina Qismullah

2014-01-01

This paper reports on students' pair-work interactions to develop their speaking skills in an ELT classroom which consisted of international learners. A number of 16 learners of intermediate proficiency with IELTS score band 5.5 were observed. The teacher had paired those he considered among them to be the more competent ones (hereafter, stronger)…

International Space Station Earth Observations Working Group

Science.gov (United States)

Stefanov, William L.; Oikawa, Koki

2015-01-01

The multilateral Earth Observations Working Group (EOWG) was chartered in May 2012 in order to improve coordination and collaboration of Earth observing payloads, research, and applications on the International Space Station (ISS). The EOWG derives its authority from the ISS Program Science Forum, and a NASA representative serves as a permanent co-chair. A rotating co-chair position can be occupied by any of the international partners, following concurrence by the other partners; a JAXA representative is the current co-chair. Primary functions of the EOWG include, 1) the exchange of information on plans for payloads, from science and application objectives to instrument development, data collection, distribution and research; 2) recognition and facilitation of opportunities for international collaboration in order to optimize benefits from different instruments; and 3) provide a formal ISS Program interface for collection and application of remotely sensed data collected in response to natural disasters through the International Charter, Space and Major Disasters. Recent examples of EOWG activities include coordination of bilateral data sharing protocols between NASA and TsNIIMash for use of crew time and instruments in support of ATV5 reentry imaging activities; discussion of continued use and support of the Nightpod camera mount system by NASA and ESA; and review and revision of international partner contributions on Earth observations to the ISS Program Benefits to Humanity publication.

Instructional materials for SARA/OSHA training. Volume 1, General site working training

Energy Technology Data Exchange (ETDEWEB)

Copenhaver, E.D.; White, D.A.; Wells, S.M. [Oak Ridge National Lab., TN (United States)

1988-04-01

This proposed 24 hour ORNL SARA/OSHA training curriculum emphasizes health and safety concerns in hazardous waste operations as well as methods of worker protection. Consistent with guidelines for hazardous waste site activities developed jointly by National Institute for Occupational Safety and Health, Occupational Safety and Health Administration, US Coast Guard, and the Envirorunental Protection Agency, the program material will address Basic Training for General Site Workers to include: ORNL Site Safety Documentation, Safe Work Practices, Nature of Anticipated Hazards, Handling Emergencies and Self-Rescue, Employee Rights and Responsibilities, Demonstration of Use, Care, and Limitations of Personal Protective, Clothing and Equipment, and Demonstration of Monitoring Equipment and Sampling Techniques. The basic training courses includes major fundamentals of industrial hygiene presented to the workers in a format that encourages them to assume responsibility for their own safety and health protection. Basic course development has focused on the special needs of ORNL facilities. Because ORNL generates chemical wastes, radioactive wastes, and mixed wastes, we have added significant modules on radiation protection in general, as well as modules on radiation toxicology and on radiation protective clothing and equipment.

The work pattern of personal care workers in two Australian nursing homes: a time-motion study

Directory of Open Access Journals (Sweden)

Qian Si-Yu

2012-09-01

Full Text Available Abstract Background The aim of the study is to describe the work pattern of personal care workers (PCWs in nursing homes. This knowledge is important for staff performance appraisal, task allocation and scheduling. It will also support funding allocation based on activities. Methods A time-motion study was conducted in 2010 at two Australian nursing homes. The observation at Site 1 was between the hours of 7:00 and 14:00 or 15:00 for 14 days. One PCW was observed on each day. The observation at Site 2 was from 10:00 to 17:00 for 16 days. One PCW working on a morning shift and another one working on an afternoon shift were observed on each day. Fifty-eight work activities done by PCWs were grouped into eight categories. Activity time, frequency, duration and the switch between two consecutive activities were used as measurements to describe the work pattern. Results Personal care workers spent about 70.0% of their time on four types of activities consistently at both sites: direct care (30.7%, indirect care (17.6%, infection control (6.4% and staff break (15.2%. Oral communication was the most frequently observed activity. It could occur independently or concurrently with other activities. At Site 2, PCWs spent significantly more time than their counterparts at Site 1 on oral communication (Site 1: 47.3% vs. Site 2: 63.5%, P = 0.003, transit (Site 1: 3.4% vs. Site 2: 5.5%, P  Conclusions At both nursing homes, direct care, indirect care, infection control and staff break occupied the major part of a PCW’s work, however oral communication was the most time consuming activity. Personal care workers frequently switched between activities, suggesting that looking after the elderly in nursing homes is a busy and demanding job.

The alternative site selection procedure as covered in the report by the Repository Site Selection Procedures Working Group; Das Verfahren der alternativen Standortsuche im Bericht des Arbeitskreises Auswahlverfahren Endlagerstandorte

Energy Technology Data Exchange (ETDEWEB)

Brenner, M. [Jena Univ. (Germany). Juristische Fakultaet

2005-01-01

The 2002 Act on the Regulated Termination of the Use of Nuclear Power for Industrial Electricity Generation declared Germany's opting out of the peaceful uses of nuclear power. The problem of the permanent management of radioactive residues is becoming more and more important also in the light of that political decision. At the present time, there are no repositories offering the waste management capacities required. Such facilities need to be created. At the present stage, eligible repository sites are the Konrad mine, a former iron ore mine near Salzgitter, and the Gorleben salt dome. While the fate of the Konrad mine as a repository for waste generating negligible amounts of heat continues to be uncertain, despite a plan approval decision of June 2002, the Gorleben repository is still in the planning phase, at present in a dormant state, so to speak. The federal government expressed doubt about the suitability of the Gorleben site. Against this backdrop, the Federal Ministry for the Environment, Nature Conservation, and Nuclear Safety in February 1999 established AkEnd, the Working Group on Repository Site Selection Procedures. The Group was charged with developing, based on sound scientific criteria, a transparent site selection procedure in order to facilitate the search for repository sites. The Working Group presented its final report in December 2002 after approximately four years of work. The Group's proposals about alternative site selection procedures are explained in detail and, above all, reviewed critically. (orig.)

Observing Pair-Work Task in an English Speaking Class

Directory of Open Access Journals (Sweden)

Diana Achmad

2014-01-01

Full Text Available This paper reports on students’ pair-work interactions to develop their speaking skills in an ELT classroom which consisted of international learners. A number of 16 learners of intermediate proficiency with IELTS score band 5.5 were observed. The teacher had paired those he considered among them to be the more competent ones (hereafter, stronger with the less competent ones (hereafter, weaker; therefore, eight pairs were observed during the lesson. The task given to the students was to express ‘Agree and Disagree’ in the context of giving opinions related to social life. Based on the observations, the task was successfully implemented by six pairs; thus, the two others faced some problems. From the first pair, it was seen that the stronger student had intimated the weaker one into speaking during the task. The other pair, who was both of the same native, did not converse in English as expected and mostly used their native language to speak with one another presumably due to respect from the stronger student towards the weaker one. In situations like this, when pair-work becomes unproductive, rotating pairs is recommended to strengthen information sharing and assigning roles to avoid a student from taking over the activity from his or her pair. In conclusion, pairing international learners with mixed speaking proficiency by teachers must be conducted as effectively as possible by initially identifying their ability and learning culture to profoundly expand the students’ language resources.

Status of birds at the Hanford Site in southeastern Washington

International Nuclear Information System (INIS)

Landeen, D.S.; Johnson, A.R.; Mitchell, R.M.

1992-06-01

The US Department of Energy has entered into agreements with the Washington State Department of Ecology, the US Environmental Protection Agency, and Hanford Site contractors to focus work activities on cleanup and stabilization of radioactive and hazardous waste sites located at the Hanford Site in southeastern Washington. Ecological characterization is an essential part of the remediation process, and the identification of biotic components such as bird species that could be impacted by cleanup activities is an important part of the initial environmental characterizations. Site characterization work has resulted in this list of 238 birds that have been observed at the Hanford Site. This list is presented with a status rating for abundance and seasonal occurrence

Iodine monoxide at a clean marine coastal site: observations of high frequency variations and inhomogeneous distributions

Directory of Open Access Journals (Sweden)

R. Commane

2011-07-01

Full Text Available The first in situ point observations of iodine monoxide (IO at a clean marine site were made using a laser-induced fluorescence instrument deployed at Mace Head, Ireland in August 2007. IO mixing ratios of up to 49.8 pptv (equivalent to pmol mol⁻¹; 1 s average were observed at day-time low tide, well in excess of previous observed spatially-averaged maxima. A strong anti-correlation of IO mixing ratios with tide height was evident and the high time resolution of the observations showed IO peaked in the hour after low tide. The temporal delay in peak IO compared to low tide has not been observed previously but coincides with the time of peak aerosol number previously observed at Mace Head.

A long path-differential optical absorption spectroscopy instrument (with a 2 × 6.8 km folded path across Roundstone Bay was also based at the site for 3 days during the point measurement observation period. Both instruments show similar temporal trends but the point measurements of IO are a factor of ~6–10 times greater than the spatially averaged IO mixing ratios, providing direct empirical evidence of the presence of inhomogeneities in the IO mixing ratio near the intertidal region.

Night Shift Work and Risk of Depression: Meta-analysis of Observational Studies.

Science.gov (United States)

Lee, Aeyoung; Myung, Seung Kwon; Cho, Jung Jin; Jung, Yu Jin; Yoon, Jong Lull; Kim, Mee Young

2017-07-01

This study aimed to assess whether night shift work is associated with the risk of depression by using a meta-analysis of observational studies. We searched PubMed and EMBASE in August, 2016 to locate eligible studies and investigated the association between night shift work and the risk of depression, reporting outcome measures with adjusted odds ratios (ORs) or relative risks (RRs) and 95% confidence intervals (CIs). In the meta-analysis of a total of 11 observational studies with 9 cross-sectional study, 1 longitudinal study, and 1 cohort study, night shift work was significantly associated with an increased risk of depression (OR/RR, 1.43; 95% CI, 1.24-1.64; I² = 78.0%). Also, subgroup meta-analyses by gender, night shift work duration, type of occupation, continent, and type of publication showed that night shift work was consistently associated with the increased risk of depression. The current meta-analysis suggests that night shift work is associated with the increased risk of depression. However, further large prospective cohort studies are needed to confirm this association. © 2017 The Korean Academy of Medical Sciences.

The role of historical operations information for supporting remedial investigation work at the former Harshaw Chemical Site

International Nuclear Information System (INIS)

Johnson, R.; Peterson, J.; Picel, K.; Kolhoff, A.; Devaughn, J.

2008-01-01

In the early stages of hazardous, toxic, and radioactive waste (HTRW) site investigations, basic record searches are performed to help direct the agencies investigating contaminated sites to areas of concern and to identify contaminants of interest (COI). Plans developed on the basis of this preliminary research alone are often incomplete and result in unexpected discoveries either while in the field investigating the site or after the reports have been written. Many of the sites investigated under the Formerly Utilized Sites Remedial Action program (FUSRAP) have complex histories that are slowly uncovered over the life of the project. Because of programmatic constraints, nuances of these sites are often discovered late in their programs and result in increased expenditures in order to fully characterize the site, perform a robust feasibility study, and recommend appropriate alternatives for remediation. By identifying resources for public records, classified records, historic aerial photographs, and other sources of site-specific historical information, a process can be established to optimize the collection of information and to develop efficient and complete project plans. In many cases, interviews with past site employees are very useful tools. In combining what is found in the records, observed on historic aerial photographs, and heard from former employees and family members, teams investigating these sites can begin to compile sound and more complete conceptual site models (CSMs). The former Harshaw Chemical Site (HCS) illustrates this discovery process. HCS is part of FUSRAP. Preliminary investigations by the US Department of Energy (DOE) in the 1970s provided an initial CSM of activities that had taken place that may have resulted in contamination. The remedial investigation (RI) conducted by the US Army Corps of Engineers (USACE) was designed around this CSM. The RI work, however, identified a number of site conditions that were unexpected, including new

Work plan addendum for David Witherspoon, Inc., 901 Site Building Characterization, Knoxville, Tennessee

International Nuclear Information System (INIS)

1997-01-01

This building characterization plan was developed as an addendum to the existing site characterization work plan documents, which are in Appendix B of the David Witherspoon, Inc., (DWI) preliminary remedial investigation (RI)/feasibility study (FS). All building characterization activities will be conducted in accordance with the rules of the Hazardous Substance Remedial Action Program under the direction of the Tennessee Department of Environment and Conservation, Division of Superfund (TN Rules 1200-1-3) and its implementing regulations. Additional rules of the state of Tennessee, Comprehensive Environmental Response, Compensation, and Liability Act of 1980, and the U.S. Environmental Protection Agency guidance were consulted during development of this plan. Activities at the DWI site were concerned with scrap metal processing and scrap metal resale

Towards observing the encounter of the T7 DNA replication fork with a lesion site at the Single molecule level

KAUST Repository

Shirbini, Afnan

2017-05-01

Single-molecule DNA flow-stretching assays have been a powerful approach to study various aspects on the mechanism of DNA replication for more than a decade. This technique depends on flow-induced force on a bead attached to a surface-tethered DNA. The difference in the elastic property between double-strand DNA (long) and single-strand DNA (short) at low regime force allows the observation of the beads motion when the dsDNA is converted to ssDNA by the replisome machinery during DNA replication. Here, I aim to develop an assay to track in real-time the encounter of the bacteriophage T7 replisome with abasic lesion site inserted on the leading strand template. I optimized methods to construct the DNA substrate that contains the abasic site and established the T7 leading strand synthesis at the single molecule level. I also optimized various control experiments to remove any interference from the nonspecific interactions of the DNA with the surface. My work established the foundation to image the encounter of the T7 replisome with abasic site and to characterize how the interactions between the helicase and the polymerase could influence the polymerase proofreading ability and its direct bypass of this highly common DNA damage type.

Calculation of risk for workers in dust working site

Directory of Open Access Journals (Sweden)

Geldová Erika

2004-03-01

Full Text Available The fibrogeneous dust is considered as a specific harmful substance in the mine working site. Such kind of dust cumulates in lungs and this fact usually results in lungs dusting, so - called pneumoconiosis. Thus, dustiness risk poses a probability of lungs damage by pneumoconiosis. For the calculation of dustiness risk it is needed to know the following data: the value of average dustiness kC in the working site per a definite time period, the dispersivity of dust “D” (it determines a portion of dust particles with a diameter under 5 µm, so - called respirable particles and the percentage content of quartz Qr in the respirable grain size fraction.The contribution presents the calculation of dustiness risk “R” according to the equation (1, where “R” is in percentage, “ša” is the analytically specific harmfulness and “KDc” is the total cumulative dust dose received by worker in time of its dust exposure.The total cumulative dust dose is calculated on the basis of the equation (4, where “kc” is the average dust concentration in the assessed time period, t–time of exposure, V –average amount of air inspired by exposed worker per time unit ( standardized on the value of 1,2 m3h-1,10-6-recalculation from mg to kg for “KDc”.If the values of “Qr”, “D” and “kc” during the worker exposure on a definite workplace are constant, the dustiness risk “R” is calculated according to the equation (1 and (5 respectively. In the case of “n” time intervals in that the values “Qr”, “D” and “kc” are known the dustiness risk “R” is calculated according to the equation (7. The total personal risk of worker is given by the equation (8.Conclusively, the influence of parameters change namely “Qr”, “D” and “kc” on the value of dustiness risk per equal time period is reported.

Review on pen-and-paper-based observational methods for assessing ergonomic risk factors of computer work.

Science.gov (United States)

Rahman, Mohd Nasrull Abdol; Mohamad, Siti Shafika

2017-01-01

Computer works are associated with Musculoskeletal Disorders (MSDs). There are several methods have been developed to assess computer work risk factor related to MSDs. This review aims to give an overview of current techniques available for pen-and-paper-based observational methods in assessing ergonomic risk factors of computer work. We searched an electronic database for materials from 1992 until 2015. The selected methods were focused on computer work, pen-and-paper observational methods, office risk factors and musculoskeletal disorders. This review was developed to assess the risk factors, reliability and validity of pen-and-paper observational method associated with computer work. Two evaluators independently carried out this review. Seven observational methods used to assess exposure to office risk factor for work-related musculoskeletal disorders were identified. The risk factors involved in current techniques of pen and paper based observational tools were postures, office components, force and repetition. From the seven methods, only five methods had been tested for reliability. They were proven to be reliable and were rated as moderate to good. For the validity testing, from seven methods only four methods were tested and the results are moderate. Many observational tools already exist, but no single tool appears to cover all of the risk factors including working posture, office component, force, repetition and office environment at office workstations and computer work. Although the most important factor in developing tool is proper validation of exposure assessment techniques, the existing observational method did not test reliability and validity. Futhermore, this review could provide the researchers with ways on how to improve the pen-and-paper-based observational method for assessing ergonomic risk factors of computer work.

The Family as a Site for Gendered Ethnic Identity Work among Asian Indian Immigrants

Science.gov (United States)

Mehrotra, Meeta; Calasanti, Toni M.

2010-01-01

Research on immigrants often points to the family as a source of support and a location for oppression. Using in-depth interviews with 38 first-generation immigrant Indians, this study adds to this literature by exploring families as sites of identity work where first-generation immigrants manage their gendered ethnic identities. Relocation into a…

Electromagnetic interference from welding and motors on implantable cardioverter-defibrillators as tested in the electrically hostile work site.

Science.gov (United States)

Fetter, J G; Benditt, D G; Stanton, M S

1996-08-01

. Our testing at the work site revealed no electrical interference with this type of defibrillator. Patients were allowed to return to work. The following precautions should be observed by the patient: 1) maintain a minimal distance of 2 ft (61 cm) from the welding arc and cables or large motors, 2) do not exceed tested currents with the welding equipment, 3) wear insulated gloves while operating electrical equipment, 4) verify that electrical equipment is properly grounded, and 5) stop welding and leave the work area immediately if a therapy is delivered or a feeling of lightheadedness is experienced.

Multi-Sensor Observations of Earthquake Related Atmospheric Signals over Major Geohazard Validation Sites

Science.gov (United States)

Ouzounov, D.; Pulinets, S.; Davindenko, D.; Hattori, K.; Kafatos, M.; Taylor, P.

2012-01-01

We are conducting a scientific validation study involving multi-sensor observations in our investigation of phenomena preceding major earthquakes. Our approach is based on a systematic analysis of several atmospheric and environmental parameters, which we found, are associated with the earthquakes, namely: thermal infrared radiation, outgoing long-wavelength radiation, ionospheric electron density, and atmospheric temperature and humidity. For first time we applied this approach to selected GEOSS sites prone to earthquakes or volcanoes. This provides a new opportunity to cross validate our results with the dense networks of in-situ and space measurements. We investigated two different seismic aspects, first the sites with recent large earthquakes, viz.- Tohoku-oki (M9, 2011, Japan) and Emilia region (M5.9, 2012,N. Italy). Our retrospective analysis of satellite data has shown the presence of anomalies in the atmosphere. Second, we did a retrospective analysis to check the re-occurrence of similar anomalous behavior in atmosphere/ionosphere over three regions with distinct geological settings and high seismicity: Taiwan, Japan and Kamchatka, which include 40 major earthquakes (M>5.9) for the period of 2005-2009. We found anomalous behavior before all of these events with no false negatives; false positives were less then 10%. Our initial results suggest that multi-instrument space-borne and ground observations show a systematic appearance of atmospheric anomalies near the epicentral area that could be explained by a coupling between the observed physical parameters and earthquake preparation processes.

Evaluation of Site and Continental Terrestrial Carbon Cycle Simulations with North American Flux Tower Observations

Science.gov (United States)

Raczka, B. M.; Davis, K. J.; Regional-Interim Synthesis Participants, N.; Site Level Interim Synthesis, N.; Regional/Continental Interim Synthesis Team

2010-12-01

Terrestrial carbon models are widely used to diagnose past ecosystem-atmosphere carbon flux responses to climate variability, and are a critical component of coupled climate-carbon model used to predict global climate change. The North American Carbon Program (NACP) Interim Regional and Site Interim Synthesis activities collected a broad sampling of terrestrial carbon model results run at both regional and site level. The Regional Interim Synthesis Activity aims to determine our current knowledge of the carbon balance of North America by comparing the flux estimates provided by the various terrestrial carbon cycle models. Moving beyond model-model comparison is challenging, however, because no continental-scale reference values exist to validate modeled fluxes. This paper presents an effort to evaluate the continental-scale flux estimates of these models using North American flux tower observations brought together by the Site Interim Synthesis Activity. Flux towers present a standard for evaluation of the modeled fluxes, though this evaluation is challenging because of the mismatch in spatial scales between the spatial resolution of continental-scale model runs and the size of a flux tower footprint. We compare model performance with flux tower observations at monthly and annual integrals using the statistical criteria of normalized standard deviation, correlation coefficient, centered root mean square deviation and chi-squared. Models are evaluated individually and according to common model characteristics including spatial resolution, photosynthesis, soil carbon decomposition and phenology. In general all regional models are positively biased for GPP, Re and NEE at both annual and monthly time scales. Further analysis links this result to a positive bias in many solar radiation reanalyses. Positively biased carbon fluxes are also observed for enzyme-kinetic models and models using no nitrogen limitation for soil carbon decomposition. While the former result is

Working Group 1: Observations

International Nuclear Information System (INIS)

Trenberth, K.; Angell, J.; Barry, R.; Bradley, R.; Diaz, H.; Elliott, W.; Etkins, R.; Folland, C.; Jenne, R.; Jones, P.; Karl, T.; Levitus, S.; Oort, A.; Parker, D.; Ropelewski, C.; Vinnikov, K.; Wigley, T.

1991-01-01

Topics of discussion include the following: the need for observations; issues in establishing global climate trends; climate variables such as surface air temperature over land, marine temperature, precipitation, circulation, upper air measurements, historical observations, subsurface ocean data, sea level, cryosphere, clouds, solar radiation, and aerosols; future considerations and recommendations which focuses on the establishment of a global benchmark climate monitoring network and data management

Working Group 1: Observations

International Nuclear Information System (INIS)

Trenberth, K.; Angell, J.; Barry, R.; Bradley, R.; Diaz, H.; Elliott, W.; Etkins, R.; Folland, C.; Jenne, R.; Jones, P.; Karl, T.; Levitus, S.; Oort, A.; Parker, D.; Ropelewski, C.; Vinnikov, K.; Wigley, T.

1990-01-01

Topics of discussion include the following: the need for observations; issues in establishing global climate trends; climate variables such as surface air temperature over land, marine temperature, precipitation, circulation, upper air measurements, historical observations, subsurface ocean data, sea level, cryosphere, clouds, solar radiation, and aerosols; future considerations and recommendations which focuses on the establishment of a global benchmark climate monitoring network and data management

Clarifying Work-Family Intervention Processes: The Roles of Work-Family Conflict and Family Supportive Supervisor Behaviors

Science.gov (United States)

Hammer, Leslie B.; Kossek, Ellen E.; Anger, W. Kent; Bodner, Todd; Zimmerman, Kristi L.

2010-01-01

Drawing on a conceptual model integrating research on training, work-family interventions, and social support, we conducted a quasi-experimental field study to assess the impact of a supervisory training and self-monitoring intervention designed to increase supervisors' use of family supportive supervisor behaviors. Pre- and post-intervention surveys were completed, nine months apart, by 239 employees at six intervention (N = 117) and six control (N = 122) grocery store sites. Thirty-nine supervisors in the six intervention sites received the training consisting of one hour of self-paced computer-based training, one hour of face-to-face group training, followed by instructions for behavioral self-monitoring (recording the frequency of supportive behaviors) to support on-the-job transfer. Results demonstrated a disordinal interaction for the effect of training and family-to-work conflict on employee job satisfaction, turnover intentions and physical health. In particular, for these outcomes, positive training effects were observed for employees with high family-to-work conflict, while negative training effects were observed for employees with low family-to-work conflict. These moderation effects were mediated by the interactive effect of training and family-to-work conflict on employee perceptions of family-supportive supervisor behaviors. Implications of our findings for future work-family intervention development and evaluation are discussed. PMID:20853943

Sunscreen use and failures--on site observations on a sun-holiday

DEFF Research Database (Denmark)

Petersen, Bibi; Datta, Pameli; Philipsen, Peter Alshede

2013-01-01

With this observation study we aimed to determine how and when sunscreen was used. 20 sun seekers were observed during a one-week sun holiday in Hurghada, Egypt. The sunscreen application thickness was related to part of body, time outdoors, exposure to ultraviolet radiation and to sunburning. Skin...... and the sunscreen application thickness was in average 0.79 mg cm(-)2 giving an approximated effect of SPF3. For different body parts either the total UVR exposure dose or the UVR exposure time and UVR exposure dose before the first sunscreen application were higher for sunburned than non-sunburned skin sites....... In the final model gender, skin type and UVR to skin (adjusted for SPF and sunscreen application thickness) were significant predictors of sunburning. The sunscreen application thickness of 0.79 mg cm(-)2 was less than the 2 mg cm(-2) used for testing SPF. The late start of sunscreen use and improper...

Brief Overlook on the Occupational Accidents Occurring During the Geotechnical Site Works

Science.gov (United States)

Akboğa Kale, Özge; Eskişar, Tuğba

2017-10-01

The aim of this paper is to evaluate occupational accidents reported in geotechnical site works. Variables of the accidents are categorized as the year and month of accidents, the technical codes used for defining the scope of work trades, end use and project type and cost, nature and cause of accidents, occupation of the victims and finally the cause of fatality. As a result, it is seen that the majority of victims were construction laborers or in special trade constructors who were working on a new project or new additions to an existing project. The geotechnical phase of the projects was whether excavation, landfill, sewer-water treatment, pipeline construction, commercial building or road construction. As the outcomes of the study it is evaluated that excavation, trenching and installing pipe or pile driving were the main causes of the accidents while trench collapse, struck by a falling object / projectile and wall collapse were the main causes of fatality. Moreover, it is established that more than half of the fatalities were due to asphyxia followed by fracture. These findings show that accidents occurred in geotechnical works do not only have high frequency but also high severity. This study emphasizes project specific countermeasures should be taken regarding the nature, cost and importance of the project and the occupation variabilities working on the project.

Recent copper-working sites in the Khuiseb drainage, Namibia

International Nuclear Information System (INIS)

Kinahan, J.

1982-01-01

In the article radiocarbon dates are presented for the production of copper artefacts in the Khomas highlands of Namibia during the last four centuries and significant associations are also briefly described. Results from the study suggest that copper beads were widely distributed in Namibia over at least the last 400 years. The archaeological evidence of copper-working in the Khuiseb valley is in partial agreement with historical records of the eighteenth century. The scale of the industry appears to have been small, and its apparent portability suited to a nonsedentary way of life based primarily on foraging. Collectively the group of radiocarbon dates suggests that copper smelting in the Khomas highlands post-dates A.D. 1420 (Pta-2573) while the activity may have continued until as late as A.D. 1840 (Pta-2739). Most of the measurements, however, point to a date in the seventeenth century indicating that the sites are roughly contemporaneous and represent a relatively short time period of about a century

CTBT on-site inspections

Science.gov (United States)

Zucca, J. J.

2014-05-01

On-site inspection (OSI) is a critical part of the verification regime for the Comprehensive Nuclear-Test-Ban Treaty (CTBT). The OSI verification regime provides for international inspectors to make a suite of measurements and observations on site at the location of an event of interest. The other critical component of the verification regime is the International Monitoring System (IMS), which is a globally distributed network of monitoring stations. The IMS along with technical monitoring data from CTBT member countries, as appropriate, will be used to trigger an OSI. After the decision is made to carry out an OSI, it is important for the inspectors to deploy to the field site rapidly to be able to detect short-lived phenomena such as the aftershocks that may be observable after an underground nuclear explosion. The inspectors will be on site from weeks to months and will be working with many tens of tons of equipment. Parts of the OSI regime will be tested in a field exercise in the country of Jordan late in 2014. The build-up of the OSI regime has been proceeding steadily since the CTBT was signed in 1996 and is on track to becoming a deterrent to someone considering conducting a nuclear explosion in violation of the Treaty.

Observation and Analysis of Particle Nucleation at a Forest Site in Southeastern US

OpenAIRE

Pillai, Priya; Khlystov, Andrey; Walker, John; Aneja, Viney

2013-01-01

This study examines the characteristics of new particle formation at a forest site in southeastern US. Particle size distributions above a Loblolly pine plantation were measured between November 2005 and September 2007 and analyzed by event type and frequency, as well as in relation to meteorological and atmospheric chemical conditions. Nucleation events occurred on 69% of classifiable observation days. Nucleation frequency was highest in spring. The highest daily nucleation (class A and B ev...

ILK statement on the recommendations by the working group on procedures for the selection of repository sites

International Nuclear Information System (INIS)

Anon.

2003-01-01

The Working Group on Procedures for the Selection of Repository Sites (AkEnd) had been appointed by the German Federal Ministry for the Environment (BMU) to develop procedures and criteria for the search for, and selection of, a repository site for all kinds of radioactive waste in deep geologic formations in Germany. ILK in principle welcomes the attempt on the part of AkEnd to develop a systematic procedure. On the other hand, ILK considers the two constraints imposed by BMU inappropriate: AkEnd was not to take into account the two existing sites of Konrad and Gorleben and, instead, work from a so-called white map of Germany. ILK recommends to perform a comprehensive safety analysis of Gorleben and define a selection procedure including the facts about Gorleben and, in addition, to commission the Konrad repository as soon as possible. The one-repository concept established as a precondition by BMU greatly restricts the selection procedure. There are no technical or scientific reasons for such concept. ILK recommends to plan for separate repositories, which would also correspond to international practice. The geoscientific criteria proposed by AkEnd should be examined and revised. With respect to the site selection procedure proposed, ILK feels that procedure is unable to define a targeted approach. Great importance must be attributed to public participation. The final site selection must be made under the responsibility of the government or the parliament. (orig.) [de

Bioventing Pilot Test Work Plan for Site ST200 (SA38), McClellan Air Force Base, California

National Research Council Canada - National Science Library

1997-01-01

This Bioventing Pilot Test Work Plan presents the scope of an in situ bioventing pilot test and installation of a bioventing system for treatment of petroleum hydrocarbon-contaminated soils at Site...

Impact of Construction Waste Disposal Charging Scheme on work practices at construction sites in Hong Kong.

Science.gov (United States)

Yu, Ann T W; Poon, C S; Wong, Agnes; Yip, Robin; Jaillon, Lara

2013-01-01

Waste management in the building industry in Hong Kong has become an important environmental issue. Particularly, an increasing amount of construction and demolition (C&D) waste is being disposed at landfill sites. In order to reduce waste generation and encourage reuse and recycling, the Hong Kong Government has implemented the Construction Waste Disposal Charging Scheme (CWDCS) to levy charges on C&D waste disposal to landfills. In order to provide information on the changes in reducing waste generation practice among construction participants in various work trades, a study was conducted after 3 years of implementation of the CWDCS via a structured questionnaire survey in the building industry in Hong Kong. The study result has revealed changes with work flows of the major trades as well as differentiating the levels of waste reduced. Three building projects in the public and private sectors were selected as case studies to demonstrate the changes in work flows and the reduction of waste achieved. The research findings reveal that a significant reduction of construction waste was achieved at the first 3 years (2006-2008) of CWDCS implementation. However, the reduction cannot be sustained. The major trades have been influenced to a certain extent by the implementation of the CWDCS. Slight improvement in waste management practices was observed, but reduction of construction waste in the wet-finishing and dry-finishing trades has undergone little improvement. Implementation of the CWDCS has not yet motivated subcontractors to change their methods of construction so as to reduce C&D waste. Copyright © 2012 Elsevier Ltd. All rights reserved.

Hanford site water table changes 1950-1980: data observations and evaluation

International Nuclear Information System (INIS)

Zimmerman, D.A.; Reisenauer, A.E.; Black, G.D.; Young, M.A.

1986-04-01

The basalt formations underlying the Hanford site are being considered for characterization and evaluation as a deep geologic repository for defense and commercial radioactive wastes. To understand the hydrology of the Hanford area, we need to know if the ground-water system is in steady state and what impact a change in surface stress from artificial recharge may have on the underlying basalt aquifers. Researchers at Pacific Northwest Laboratory are supporting efforts to understand these issues by illustrating how changes in wastewater disposal activities at the Hanford site have altered the configuration of the water table surface with time. The objective of this work was to determine the magnitude and direction of changes in the elevation of the water table across the Hanford site from 1950 to 1980. Plots of the magnitudes of water-level changes occurring over 5-year intervals from 1950 through 1980 are presented. The water-level changes that occurred during each 5-year interval are related to water discharges from nuclear fuel reprocessing facilities or other discharge sources. The plots of water-level changes show large water-level increases in the vicinity of the Separations Area (200 East and 200 West) from 1950 to 1960; the rate of increase of water-level changes grows more slowly from 1960 to 1970, while the areal extent of the mounding continues to expand. Only small changes occur from 1970 to 1980; during this time period, the unconfined system appears to be in approximate equilibrium with the sources. Based on previous experience, it is believed that an increase in ground-water mounding will begin to appear near the 200 East Area B Pond as a result of the increased discharges from the restart of PUREX in 1983

Caxingo - a promising model for integrating the hydroelectric work camps to the site communities

International Nuclear Information System (INIS)

Luna, A.M.; Falcao, A.A.

1989-01-01

The social and economical impacts caused by the hydroelectric work camps in the sites where the hydroelectric will be constructed are studied, analysing the great supply of works when the hydroelectric is been constructed face to the reduction one when the works are concluded; the neglect by the State in providing medical and educational assistances to the neighbour populations; the appearance of a commerce in the neighbour areas; the employer stableness in the camp after the pension and the lack by the neighbour cities of a social and economical substructure to offer to the population, that come with the hydroelectric construction. A new solution for these problems is presented in the Xingo camp, where the camp will be as a district of city near to the work, with community services provide by the State and the needful substructure to its construction and the equipment provide by the concessionaire. (C.G.C.). 1 fig

Danish Observational Study of Eldercare work and musculoskeletal disorderS (DOSES)

DEFF Research Database (Denmark)

Karstad, Kristina; Jørgensen, Anette F B; Greiner, Birgit A

2018-01-01

PURPOSE: Musculoskeletal disorders (MSDs), sickness absence and premature retirement are highly prevalent among eldercare workers. We conducted a prospective observational workplace study with the main purpose to investigate longitudinal associations between physical and psychosocial working...... and team factors for distribution of physical work demands and development of MSD among the workers. This will provide important knowledge for future workplace interventions to reduce MSD and sickness absence....... conditions and occurrence of MSD and its consequences (pain-related interference with daily work activities and sickness absence) among Danish eldercare workers. PARTICIPANTS: At 20 Danish nursing homes, a total of 941 eldercare workers employed in day and evening shifts were invited to the study. Of those...

HAZWOPER work plan and site safety and health plan for the Alpha characterization project at the solid waste storage area 4 bathtubbing trench at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

1994-07-01

This work plan/site safety and health plan is for the alpha sampling project at the Solid Waste Storage Area 4 bathtubbing trench. The work will be conducted by the Oak Ridge National Laboratory (ORNL) Environmental Sciences Division and associated ORNL environmental, safety, and health support groups. This activity will fall under the scope of 29 CFR 1910.120, Hazardous Waste Operations and Emergency Response (HAZWOPER). The purpose of this document is to establish health and safety guidelines to be followed by all personnel involved in conducting work for this project. Work will be conducted in accordance with requirements as stipulated in the ORNL HAZWOPER Program Manual and applicable ORNL; Martin Marietta Energy Systems, Inc.; and U.S. Department of Energy policies and procedures. The levels of protection and the procedures specified in this plan are based on the best information available from historical data and preliminary evaluations of the area. Therefore, these recommendations represent the minimum health and safety requirements to be observed by all personnel engaged in this project. Unforeseeable site conditions or changes in scope of work may warrant a reassessment of the stated protection levels and controls. All adjustments to the plan must have prior approval by the safety and health disciplines signing the original plan

Work impairment in bipolar disorder patients--results from a two-year observational study (EMBLEM).

Science.gov (United States)

Reed, C; Goetz, I; Vieta, E; Bassi, M; Haro, J M

2010-10-01

To explore factors associated with work impairment at 2 years following an acute episode. European Mania in Bipolar disorder Longitudinal Evaluation of Medication (EMBLEM) is a prospective, observational study on the outcomes of patients with a manic/mixed episode. Work impairment was measured using a Longitudinal Interval Follow-up Evaluation (slice of LIFE) item and patients were categorised with either low or high work impairment at each observation. Baseline factors associated with work impairment at 2 years were assessed using multivariate modelling. At baseline (n=2289), 69% of patients had high work impairment. At 2 years (n=1393), high impairment reduced to 41%. Modelling identified rapid cycling as the strongest disease-related factor associated with high work impairment at 2 years, although high work impairment at baseline had the strongest association overall. Lower levels of education, recent admissions, CGI-BP overall severity in the 12 months prior to baseline and CGI-BP mania at baseline all predicted higher work impairment. Living together in a relationship and independent housing were both significantly associated with having low work impairment at 2 years. Work impairment in bipolar disorder is maintained over long periods, and is strongly associated with relationship status, living conditions and various disease-related factors. Copyright © 2010 Elsevier Masson SAS. All rights reserved.

Inter-rater reliability of direct observations of the physical and psychosocial working conditions in eldercare

DEFF Research Database (Denmark)

Karstad, Kristina; Rugulies, Reiner; Skotte, Jørgen

2018-01-01

The aim of the study was to develop and evaluate the reliability of the "Danish observational study of eldercare work and musculoskeletal disorders" (DOSES) observation instrument to assess physical and psychosocial risk factors for musculoskeletal disorders (MSD) in eldercare work. During 1...... is appropriate for assessing physical and psychosocial risk factors for MSD among eldercare workers....

Prevalence of work-site injuries and relationship between obesity and injury among U.S. workers: NHIS 2004-2012.

Science.gov (United States)

Gu, Ja K; Charles, Luenda E; Andrew, Michael E; Ma, Claudia C; Hartley, Tara A; Violanti, John M; Burchfiel, Cecil M

2016-09-01

Studies have reported associations between obesity and injury in a single occupation or industry. Our study estimated the prevalence of work-site injuries and investigated the association between obesity and work-site injury in a nationally representative sample of U.S. workers. Self-reported weight, height, and injuries within the previous three months were collected annually for U.S. workers in the National Health Interview Survey (NHIS) from 2004-2012. Participants were categorized as normal weight (BMI: 18.5-24.9kg/m(2)), overweight (BMI: 25.0-29.9), obese I (BMI: 30.0-34.9), and obese II (BMI: 35+). The prevalence of injury and prevalence ratios from fitted logistic regression models was used to assess relationships between obesity and injury after adjusting for covariates. Sampling weights were incorporated using SUDAAN software. During the 9-year study period from 2004 to 2012, 1120 workers (78 workers per 10,000) experienced a work-related injury during the previous three months. The anatomical sites with the highest prevalence of injury were the back (14.3/10,000±1.2), fingers (11.5±1.3), and knees (7.1±0.8). The most common types of injuries were sprains/strains/twists (41.5% of all injuries), cuts (20.0%), and fractures (11.8%). Compared to normal weight workers, overweight and obese workers were more likely to experience work-site injuries [overweight: PR=1.25 (95% CI=1.04-1.52); obese I: 1.41 (1.14-1.74); obese II: 1.68 (1.32-2.14)]. These injuries were more likely to affect the lower extremities [overweight: PR=1.48, (95% CI=1.03-2.13); obese I: 1.70 (1.13-2.55); obese II: 2.91 (1.91-4.41)] and were more likely to be due to sprains/strains/twists [overweight: PR=1.73 (95% CI=1.29-2.31); obese I: PR=2.24 (1.64-3.06); obese II: PR=2.95 (2.04-4.26)]. Among NHIS participants, overweight and obese workers were 25% to 68% more likely to experience injuries than normal weight workers. Weight reduction policies and management programs may be effectively

Humboldt Open Ocean Disposal Site (HOODS) Survey Work 2014

Data.gov (United States)

U.S. Environmental Protection Agency — The Humboldt Open Ocean Disposal Site (HOODS) is a dredged material disposal site located 3 nautical miles (nm) offshore of Humboldt Bay in Northern California....

RCRA facility investigation/corrective measures study work plan for the 200-UP-2 Operable Unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1993-06-01

The 200-UP-2 Operable Unit is one of two source operable units at the U Plant Aggregate Area at the Hanford Site. Source operable units include waste management units and unplanned release sites that are potential sources of radioactive and/or hazardous substance contamination. This work plan, while maintaining the title RFI/CMS, presents the background and direction for conducting a limited field investigation in the 200-UP-2 Operable Unit, which is the first part of the process leading to final remedy selection. This report discusses the background, prior recommendations, goals, organization, and quality assurance for the 200-UP-2 Operable Unit Work Plan. The discussion begins with a summary of the regulatory framework and the role of the work plan. The specific recommendations leading into the work plan are then addressed. Next, the goals and organization of the report are discussed. Finally, the quality assurance and supporting documentation are presented

Radionuclide migration in groundwater at a low-level waste disposal site: a comparison of predictive performance modeling versus field observations

International Nuclear Information System (INIS)

Robertson, D.E.; Myers, D.A.; Bergeron, M.P.; Champ, D.R.; Killey, R.W.D.; Moltyaner, G.L.; Young, J.L.

1985-08-01

This paper describes a project which is structured to test the concept of modeling a shallow land low-level waste burial site. The project involves a comparison of the actual observed radionuclide migration in groundwaters at a 30-year-old well-monitored field site with the results of predictive transport modeling. The comparison is being conducted as a cooperative program with the Atomic Energy of Canada Ltd. (AECL) at the low-level waste management area at the Chalk River Nuclear Laboratories, Ontario, Canada. A joint PNL-AECL field inviestigation was conducted in 1983 and 1984 to complement the existing extensive data base on actual radionuclide migration. Predictive transport modeling is currently being conducted for this site; first, as if it were a new location being considered for a low-level waste shallow-land burial site and only minimal information about the site were available, and second, utilizing the extensive data base available for the site. The modeling results will then be compared with the empirical observations to provide insight into the level of effort needed to reasonably predict the spacial and temporal movement of radionuclides in the groundwater enviroment. 8 refs., 5 figs.,

Observation and Analysis of Particle Nucleation at a Forest Site in Southeastern US

Directory of Open Access Journals (Sweden)

Viney Aneja

2013-04-01

Full Text Available This study examines the characteristics of new particle formation at a forest site in southeastern US. Particle size distributions above a Loblolly pine plantation were measured between November 2005 and September 2007 and analyzed by event type and frequency, as well as in relation to meteorological and atmospheric chemical conditions. Nucleation events occurred on 69% of classifiable observation days. Nucleation frequency was highest in spring. The highest daily nucleation (class A and B events frequency (81% was observed in April. The average total particle number concentration on nucleation days was 8,684 cm−3 (10 < Dp < 250 nm and 3,991 cm−3 (10 < Dp < 25 nm with a mode diameter of 28 nm with corresponding values on non-nucleation days of 2,143 cm−3, 655 cm−3, and 44.5 nm, respectively. The annual average growth rate during nucleation events was 2.7 ± 0.3 nm·h−1. Higher growth rates were observed during summer months with highest rates observed in May (5.0 ± 3.6 nm·h−1. Winter months were associated with lower growth rates, the lowest occurring in February (1.2 ± 2.2 nm·h−1. Consistent with other studies, nucleation events were more likely to occur on days with higher radiative flux and lower relative humidity compared to non-nucleation days. The daily minimum in the condensation sink, which typically occurred 2 to 3 h after sunrise, was a good indicator of the timing of nucleation onset. The intensity of the event, indicated by the total particle number concentration, was well correlated with photo-synthetically active radiation, used here as a surrogate for total global radiation, and relative humidity. Even though the role of biogenic VOC in the initial nuclei formation is not understood from this study, the relationships with chemical precursors and secondary aerosol products associated with nucleation, coupled with diurnal boundary layer dynamics and seasonal meteorological patterns, suggest that H2SO4 and biogenic

Thermal interaction effect on nucleation site distribution in subcooled boiling

International Nuclear Information System (INIS)

Zou, Ling; Jones, Barclay

2012-01-01

An experimental work on subcooled boiling of refrigerant, R134a, to examine nucleation site distributions on both copper and stainless steel heating surfaces was performed. In order to obtain high fidelity active nucleation site density and distribution data, a high-speed digital camera was utilized to record bubble emission images from a view normal to heating surfaces. Statistical analyses on nucleation site data were done and their statistical distributions were obtained. Those experimentally observed nucleation site distributions were compared to the random spatial Poisson distribution. The comparisons showed that, rather than purely random, active nucleation site distributions on boiling surfaces are relatively more uniform. Experimental results also showed that on the copper heating surface, nucleation site distributions are slightly more uniform than on the stainless steel surface. This was concluded as the results of thermal interactions between nucleation sites with different solid thermal conductivities. A two dimensional thermal interaction model was then developed to quantitatively examine the thermal interactions between nucleation sites. The results give a reasonable explanation to the experimental observation on nucleation site distributions.

Remedial investigation/feasibility study work plan for the 100-BC-2 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1993-05-01

This work plan and attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) remedial investigation/feasibility study (RI/FS) for the 100-BC-2 operable unit in the 100 Area of the Hanford Site. The 100 Area is one of four areas at the Hanford Site that are on the US Environmental Protection Agency's (EPA) National Priorities List under CERCLA. The 100-BC-2 operable unit is one of two source operable units in the 100-B/C Area (Figure ES-1). Source operable units are those that contain facilities and unplanned release sites that are potential sources of hazardous substance contamination. The 100-BC-2 source operable unit contains waste sites that were formerly in the 100-BC-2, 100-BC-3, and 100-BC-4 operable units. Because of their size and geographic location, the waste sites from these two operable units were added to 100-BC-2. This allows for a more efficient and effective investigation of the remaining 100-B/C Reactor area waste sites. The investigative approach to waste sites associated with the 100-BC-2 operable unit are listed in Table ES-1. The waste sites fall into three general categories: high priority liquid waste disposal sites, low priority liquid waste disposal sites, and solid waste burial grounds. Several sites have been identified as candidates for conducting an IRM. Two sites have been identified as warranting additional limited field sampling. The two sites are the 116-C-2A pluto crib, and the 116-C-2C sand filter

Measuring the quality of MDT working: an observational approach

Directory of Open Access Journals (Sweden)

Taylor Cath

2012-05-01

Full Text Available Abstract Background Cancer multidisciplinary teams (MDTs are established in many countries but little is known about how well they function. A core activity is regular MDT meetings (MDMs where treatment recommendations are agreed. A mixed methods descriptive study was conducted to develop and test quality criteria for observational assessment of MDM performance calibrated against consensus from over 2000 MDT members about the “characteristics of an effective MDT”. Methods Eighteen of the 86 ‘Characteristics of Effective MDTs’ were considered relevant and feasible to observe. They collated to 15 aspects of MDT working covering four domains: the team (e.g. attendance, chairing, teamworking; infrastructure for meetings (venue, equipment; meeting organisation and logistics; and patient-centred clinical decision-making (patient-centredness, clarity of recommendations. Criteria for rating each characteristic from ‘very poor’ to ‘very good’ were derived from literature review, observing MDMs and expert input. Criteria were applied to 10 bowel cancer MDTs to assess acceptability and measure variation between and within teams. Feasibility and inter-rater reliability was assessed by comparing three observers. Results Observational assessment was acceptable to teams and feasible to implement. Total scores from 29 to 50 (out of 58 highlighted wide diversity in quality between teams. Eight teams were rated either ‘very good/good’ or ‘very poor/poor’ for at least three domains demonstrating some internal consistency. ‘Very good’ ratings were most likely for attendance and administrative preparation, and least likely for patient-centredness of decision-making and prioritisation of complex cases. All except two characteristics had intra-class correlations of ≥0.50. Conclusions This observational tool (MDT-OARS may contribute to the assessment of MDT performance. Further testing to confirm validity and reliability is required.

Evaluation of Fourier and Response Spectra at Ichihasama and Koromogawa Seismic Intensity Observation Sites During the Iwate-Miyagi Nairiku Earthquake in 2008

Science.gov (United States)

Nishikawa, Hayato; Miyajima, Masakatsu

In this study, we evaluate an acceleration Fourier and response spectra at Ichihasama and Koromogawa seismic intensity observation sites which observed JMA seismic intensity of 6 upper but seismic waveform records don't exist during the Iwate-Miyagi Nairiku earthquake in 2008. Firstly, formula to evaluate acceleration Fourier and response spectra are developed using peak ground acceleration, JMA seismic intensity and predominant period of earthquake spectra based on records obtained from crustal earthquakes with Magnitude of 6 to 7. Acceleration Fourier and response spectra are evaluated for another local government site which are not chosen for development of the formula. The evaluated values mostly agree with the observed ones. Finally, acceleration Fourier and response spectra are evaluated for Ichihasama and Koromogawa observation sites. It is clarified that short period below 1 second was predominated in the evaluated spectra.

Important considerations related to the construction of observation wells in radiation facilities sites: A review research

International Nuclear Information System (INIS)

El-Sayed, S. A.; Salem, W. M.; Atta, E. R.

2012-01-01

Observation wells in radiation facility sites are considered the main sources of the required subsurface geologic and hydrogeologic data. They are the most important means to detect the radioactive and/or chemical contaminants within the ground water. Also, they are used to observe the groundwater level fluctuations and perform the different aquifer tests to understand the hydraulic properties of aquifers and the behavior of contaminants transportation. This research reviews the necessary considerations and available techniques for constructing the observation wells properly. The review process depends on the international guidelines presented in the literature and the field experience. The proper well completion is essential for the well efficiency and longevity. Three main important topics are considered and discussed briefly in this review. They are the preliminary considerations, the drilling program and the well protection procedures. The preliminary considerations included are the collection of the available geologic and hydrogeologic data and information, selection of drilling method and the legal requirements. The drilling program comprises the site preparation, drilling processes, sampling, well logging, well design, casing components and materials, gravel pack and well development. The well protection procedures include well grout, concrete slab and others requirements. Observation wells should be constructed to a high standard and should be properly maintained and protected to ensure ongoing and reliable data collection

Remedial investigation/feasibility study work plan for the 100-FR-3 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-09-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Figure 1-1 shows the location of these areas. Under the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement, Ecology et al. 1990a), signed by the Washington State Department of Ecology (Ecology), EPA, and the US Department of Energy (DOE), more than 1,000 inactive waste disposal and unplanned release sites on the Hanford Site have been grouped into a number of source and groundwater operable units. These operable units contain contamination in the form of hazardous waste, radioactive/hazardous mixed waste, and other CERCLA hazardous substances. This work plan and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the CERCLA remedial investigation/feasibility study (RI/FS) for the 100-FR-3 operable unit. The 100-K Area consists of the 100-FR-3 groundwater operable unit and two source operable units. The 100-FR-3 operable unit includes all contamination found in the aquifer soils and water beneath the 100-F Area. Source operable units include facilities and unplanned release sites that are potential sources of contamination. A separate work plan has been initiated for the 100-FR-1 source operable unit (DOE-RL 1992a)

Remedial investigation/feasibility study work plan for the 100-FR-1 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-08-01

Four areas of the Hanford Site (the 100, 200,300, and 1100 Areas) have been included on the US Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Under the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement, Ecology et al. 1990a), signed by the Washington State Department of Ecology (Ecology), EPA, and the US Department of Energy (DOE), more than 1,000 inactive waste disposal and unplanned release sites on the Hanford Site have been grouped into a number of source and groundwater operable units. These operable units contain contamination in the form of hazardous waste, radioactive/hazardous mixed waste, and other CERCLA hazardous substances. This work plan and the attached supporting project plans establish the objectives, procedures, tasks, and schedule for conducting the CERCLA remedial investigation/feasibility study (RI/FS) for the 100-FR-1 operable unit. The 100-FR-1 source operable unit is one of two source operable units in the 100-F Area. Source operable units include facilities and unplanned release sites that are potential sources of hazardous substance contamination. The groundwater affected or potentially affected by the entire 100-F Area is considered as a separate operable unit, the 100-FR-3 groundwater operable unit. A separate work plan has been initiated for the 100-FR-3 operable unit (DOE/RL 1992a)

Future enhanced clinical role of pharmacists in emergency departments in England:multi-site observational evaluation

OpenAIRE

Hughes, Elizabeth; Terry, David; Huynh, Chi; Petridis, Konstantinos; Aiello, Matthew; Mazard, Louis; Ubhi, Hirminder; Terry, Alex; Wilson, Keith; Sinclair, Anthony

2017-01-01

Background There are concerns about maintaining appropriate clinical staffing levels in Emergency Departments. Pharmacists may be one possible solution. Objective To determine if Emergency Department attendees could be clinically managed by pharmacists with or without advanced clinical practice training. Setting Prospective 49 site cross-sectional observational study of patients attending Emergency Departments in England. Method Pharmacist data collectors identified patient attendance at thei...

Methane ebullition fluxes from northern peatlands: initial observations from four sites of contrasting vegetation type in Caribou Bog, ME

Science.gov (United States)

Slater, L. D.; Comas, X.; Mumford, K. G.; Reeve, A. S.; Varner, R. K.; Chen, X.; Wright, W.; Wright, J.; Molnar, I. L.; Krol, M.

2017-12-01

The contribution of peatlands to the atmospheric CH4 burden remains unclear in large part due to incomplete understanding of the ebullition pathway. Oxidation of dissolved methane reduces the release of methane by diffusion, but the transit time of bubbles released via ebullition is too short for extensive oxidation to occur, i.e. ebullition releases increase the greenhouse gas potential of peatlands. We are working to couple innovative strategies for ebullition monitoring with a physical model describing gas transport in terms of the mechanical properties of the peat. This integration of measurement and modeling will permit a fundamental step forward towards a more quantitative understanding of CH4 ebullition from peatlands. Sampling and sensor installation have been performed in Caribou Bog, a multi-unit peatland located in Maine (USA) where an extensive database accounting for a decade of research is already available from previous work examining methane dynamics. Multi-depth gas trap and moisture probe arrays have been installed at four sites selected based on contrasting vegetation type and peat basin depth determined from extensive ground penetrating radar surveys. Hydraulic head measurements have also been acquired on multi-level piezometers designed to capture transient signals associated with gas transport. Cores and initial field observations acquired in summer 2017 confirm that the physical properties of the peat vary markedly between the sites and influence gas storage and release. An existing ebullition model describing gas bubble expansion is being coupled with an invasion percolation approach to describe the transport of CH4 between multiple peat layers by both diffusion in the pore water and ebullition between layers. Although the proposed model does not explicitly incorporate the geomechanical properties of peat, model predictions for maximum gas contents are being compared with key measurable geomechanical properties (including measured capillary

Work site health promotion research: to what extent can we generalize the results and what is needed to translate research to practice?

Science.gov (United States)

Bull, Sheana Salyers; Gillette, Cynthia; Glasgow, Russell E; Estabrooks, Paul

2003-10-01

Information on external validity of work site health promotion research is essential to translate research findings to practice. The authors provide a literature review of work site health behavior interventions. Using the RE-AIM framework, they summarize characteristics and results of these studies to document reporting of intervention reach, adoption, implementation, and maintenance. The authors reviewed a total of 24 publications from 11 leading health behavior journals. They found that participation rates among eligible employees were reported in 87.5% of studies; only 25% of studies reported on intervention adoption. Data on characteristics of participants versus nonparticipants were reported in fewer than 10% of studies. Implementation data were reported in 12.5% of the studies. Only 8% of studies reported any type of maintenance data. Stronger emphasis is needed on representativeness of employees, work site settings studied, and longer term results. Examples of how this can be done are provided.

Impact of Construction Waste Disposal Charging Scheme on work practices at construction sites in Hong Kong

International Nuclear Information System (INIS)

Yu, Ann T.W.; Poon, C.S.; Wong, Agnes; Yip, Robin; Jaillon, Lara

2013-01-01

Highlights: ► A significant reduction of construction waste was achieved at the first 3 years of CWDCS implementation. ► However, the reduction cannot be sustained. ► Implementation of the CWDCS has generated positive effects in waste reduction by all main trades. - Abstract: Waste management in the building industry in Hong Kong has become an important environmental issue. Particularly, an increasing amount of construction and demolition (C and D) waste is being disposed at landfill sites. In order to reduce waste generation and encourage reuse and recycling, the Hong Kong Government has implemented the Construction Waste Disposal Charging Scheme (CWDCS) to levy charges on C and D waste disposal to landfills. In order to provide information on the changes in reducing waste generation practice among construction participants in various work trades, a study was conducted after 3 years of implementation of the CWDCS via a structured questionnaire survey in the building industry in Hong Kong. The study result has revealed changes with work flows of the major trades as well as differentiating the levels of waste reduced. Three building projects in the public and private sectors were selected as case studies to demonstrate the changes in work flows and the reduction of waste achieved. The research findings reveal that a significant reduction of construction waste was achieved at the first 3 years (2006–2008) of CWDCS implementation. However, the reduction cannot be sustained. The major trades have been influenced to a certain extent by the implementation of the CWDCS. Slight improvement in waste management practices was observed, but reduction of construction waste in the wet-finishing and dry-finishing trades has undergone little improvement. Implementation of the CWDCS has not yet motivated subcontractors to change their methods of construction so as to reduce C and D waste.

Impact of Construction Waste Disposal Charging Scheme on work practices at construction sites in Hong Kong

Energy Technology Data Exchange (ETDEWEB)

Yu, Ann T.W., E-mail: bsannyu@polyu.edu.hk [Department of Building and Real Estate, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Poon, C.S.; Wong, Agnes; Yip, Robin; Jaillon, Lara [Department of Civil and Structural Engineering, Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong)

2013-01-15

Highlights: Black-Right-Pointing-Pointer A significant reduction of construction waste was achieved at the first 3 years of CWDCS implementation. Black-Right-Pointing-Pointer However, the reduction cannot be sustained. Black-Right-Pointing-Pointer Implementation of the CWDCS has generated positive effects in waste reduction by all main trades. - Abstract: Waste management in the building industry in Hong Kong has become an important environmental issue. Particularly, an increasing amount of construction and demolition (C and D) waste is being disposed at landfill sites. In order to reduce waste generation and encourage reuse and recycling, the Hong Kong Government has implemented the Construction Waste Disposal Charging Scheme (CWDCS) to levy charges on C and D waste disposal to landfills. In order to provide information on the changes in reducing waste generation practice among construction participants in various work trades, a study was conducted after 3 years of implementation of the CWDCS via a structured questionnaire survey in the building industry in Hong Kong. The study result has revealed changes with work flows of the major trades as well as differentiating the levels of waste reduced. Three building projects in the public and private sectors were selected as case studies to demonstrate the changes in work flows and the reduction of waste achieved. The research findings reveal that a significant reduction of construction waste was achieved at the first 3 years (2006-2008) of CWDCS implementation. However, the reduction cannot be sustained. The major trades have been influenced to a certain extent by the implementation of the CWDCS. Slight improvement in waste management practices was observed, but reduction of construction waste in the wet-finishing and dry-finishing trades has undergone little improvement. Implementation of the CWDCS has not yet motivated subcontractors to change their methods of construction so as to reduce C and D waste.

Characteristics of Volcanic Stratospheric Aerosol Layer Observed by CALIOP and Ground Based Lidar at Equatorial Atmosphere Radar Site

Science.gov (United States)

Abo, Makoto; Shibata, Yasukuni; Nagasawa, Chikao

2018-04-01

We investigated the relation between major tropical volcanic eruptions in the equatorial region and the stratospheric aerosol data, which have been collected by the ground based lidar observations at at Equatorial Atmosphere Radar site between 2004 and 2015 and the CALIOP observations in low latitude between 2006 and 2015. We found characteristic dynamic behavior of volcanic stratospheric aerosol layers over equatorial region.

Radioecological surveillance around an old mining and milling site during environmental remediation works

International Nuclear Information System (INIS)

Carvalho, Fernando P.; Oliveira, Joao M.; Malta, Margarida

2008-01-01

The main site of historic uranium mining and milling in Portugal, near the town of Canas de Senhorim, contains around 2.5 million tones of solid waste containing radioactivity in various mill tailings and spoil heaps. Approval of an environmental remediation plan for this area was followed by the start of engineering works, including the transportation of milling waste to the main milling pile and re shaping and contouring the waste heap to put a cap layer. These works were mostly performed in 2006 and 2007. During part of this period monitoring of radioactivity, including radon, was performed in the surface air, surface waters from the area, including the monitoring of the small river that receives drainage from the mill tailings area, and agriculture products. This paper presents the results of measurements of the main alpha emitting radionuclides of uranium series and compares them with previous data from the region. Implications for the radiological protection of the population are discussed. (author)

Safety procedures for radiography works

International Nuclear Information System (INIS)

Abd Nasir Ibrahim; Azali Muhammad; Ab Razak Hamzah; Abd Aziz Mohamed; Mohammad Pauzi Ismail

2004-01-01

The following subjects are discussed - Work preparation: before exposure, during exposure, after work completion. Radiographic work at the open site: types of open sites, establishment of radiographic boundary, storage of radiographic equipment at sites. Safety procedures for radiography works; radiographic works in exposure room

Observations of a Working Class Family: Implications for Self-Regulated Learning Development

Science.gov (United States)

Vassallo, Stephen

2012-01-01

Guardians have been implicated in the development of children's academic self-regulation. In this case study, which involved naturalistic observations and interviews, the everyday practices of a working class family were considered in the context of self-regulated learning development. The family's practices, beliefs, dispositions and home…

Observations at the Mars Pathfinder site: Do they provide "unequivocal" evidence of catastrophic flooding?

Science.gov (United States)

Chapman, M.G.; Kargel, J.S.

1999-01-01

After Mars Pathfinder landed at the mouth of Ares Vallis, a large channel that drains into the Chryse Planitia basin, the mission reports unanimously supported the interpretation that the lander site is the locus of catastrophic flooding by noting that all aspects of the scene are consistent with this interpretation. However, alternatives cannot be ruled out by any site observations, as all aspects of the scene are equally consistent with other interpretations of origin, namely, ice and mass-flow processes subsequently modified by wind erosion. The authors discuss alternative explanations for the geologic history of the channel based on a regional view of the circum-Chryse channels from Viking images (our best broad-scale information to date) and the local view from the recent Pathfinder landing site. Mega-indicators of channel origin, the regional geomorphology, geology, and planetary climatic conditions, taken together suggest some combination of flood, mass flow, glacial, and eolian processes. The macro-indicators of channel origin (sedimentologic) are also not indicative of one process of emplacement, either as single criteria or taken cumulatively. Finally, the micro-indicators of channel origin (geochemical and mineralogic composition) do not provide very tight constraints on the deposits' possible origins other than that water was in some way involved.

Two-year concurrent observation of isoprene at 20 sites over China: comparison with MEGAN-REAM model simulation

Science.gov (United States)

Zhang, Y.; Yang, W.; Zhang, R.; Zhang, Z.; Lyu, S.; Yu, J.; Wang, Y.; Wang, G.; Wang, X.

2017-12-01

Isoprene, the most abundant non-methane hydrocarbon emitted from plants, directly and indirectly affects atmospheric photochemistry and radiative forcing, yet narrowing its emission uncertainties is a continuous challenge. Comparison of observed and modelled isoprene on large spatiotemporal scales would help recognize factors that control isoprene variability, systematic field observation data are however quite lacking. Here we collected ambient air samples with 1 L silonite-treated stainless steel canisters simultaneously at 20 sites over China on every Wednesday at approximately 14:00 pm Beijing time from 2012 to 2014, and analyzed isoprene mixing ratios by preconcentrator-GC-MSD/FID. Observed isoprene mixing ratios were also compared with that simulated by coupling MEGAN 2.0 (Guenther et al., 2006) with a 3-D Regional chEmical trAnsport Model (REAM) (Zhang et al., 2017). Similar seasonal variations between observation and model simulation were obtained for most of sampling sites, but overall the average isoprene mixing ratios during growing months (May to October) was 0.37 ± 0.08 ppbv from model simulation, about 32% lower than that of 0.54 ± 0.20 ppbv based on ground-based observation, and this discrepancy was particularly significant in north China during wintertime. Further investigation demonstrated that emission of biogenic isoprene in northwest China might be underestimated and non-biogenic emission, such burning biomass/biofuel, might contribute to the elevated levels of isoprene during winter time. The observation-based empirical formulas for changing isoprene emission with solar radiation and temperature were also derived for different regions of China.

Site specific information in site selection

International Nuclear Information System (INIS)

Aeikaes, T.; Hautojaervi, A.

1998-01-01

The programme for the siting of a deep repository for final disposal of spent nuclear fuel was started already in 1983 and is carried out today by Posiva Oy which continues the work started by Teollisuuden Voima Oy. The programme aims at site selection by the end of the year 2000. The programme has progressed in successive interim stages with defined goals. After an early phase for site identification, five sites were selected in 1987 for preliminary site characterisation. Three of these were selected and judged to be best suited for the more detailed characterisation in 1992. An additional new site was included into the programme based on a separate feasibility study in the beginning of 1997. Since the year 1983 several safety assessments together with technical plans of the facility have been completed. When approaching the site selection the needs for more detailed consideration of the site specific properties in the safety assessment have been increased. The Finnish regulator STUK has published a proposal for general safety requirements for the final disposal of spent nuclear fuel in Finland. This set of requirements has been projected to be used in conjunction of the decision making by the end 2000. Based on the site evaluation all sites can provide a stable environment and there is evidence that the requirements for the longevity of the canister can be fulfilled at each site. In this manner the four candidate sites do not differ too much from each other. The main difference between the sites is in the salinity of the deep groundwater. The significance of differences in the salinity for the long-term safety cannot be defined yet. The differences may contribute to the discussion of the longevity of the bentonite buffer and also to the modelling of the groundwater flow and transport. The use of the geosphere as a transport barrier is basically culminated on the questions about sparse but fast flow routes and 'how bad channeling can be'. To answer these questions

Site selection - siting of the final repository for spent nuclear fuel

International Nuclear Information System (INIS)

2011-03-01

SKB has selected Forsmark as the site for the final repository for spent nuclear fuel. The site selection is the end result of an extensive siting process that began in the early 1990s. The strategy and plan for the work was based on experience from investigations and development work over a period of more than ten years prior to then. This document describes the siting work and SKB's choice of site for the final repository. It also presents the information on which the choice was based and the reasons for the decisions made along the way. The document comprises Appendix PV to applications under the Nuclear Activities Act and the Environmental Code for licences to build and operate an encapsulation plant adjacent to the central interim storage facility for spent nuclear fuel in Oskarshamn, and to build and operate a final repository for spent nuclear fuel in Forsmark in Oesthammar Municipality

Site selection - siting of the final repository for spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

2011-03-15

SKB has selected Forsmark as the site for the final repository for spent nuclear fuel. The site selection is the end result of an extensive siting process that began in the early 1990s. The strategy and plan for the work was based on experience from investigations and development work over a period of more than ten years prior to then. This document describes the siting work and SKB's choice of site for the final repository. It also presents the information on which the choice was based and the reasons for the decisions made along the way. The document comprises Appendix PV to applications under the Nuclear Activities Act and the Environmental Code for licences to build and operate an encapsulation plant adjacent to the central interim storage facility for spent nuclear fuel in Oskarshamn, and to build and operate a final repository for spent nuclear fuel in Forsmark in Oesthammar Municipality

Future-oriented maintenance strategy based on automated processes is finding its way into large astronomical facilities at remote observing sites

Science.gov (United States)

Silber, Armin; Gonzalez, Christian; Pino, Francisco; Escarate, Patricio; Gairing, Stefan

2014-08-01

With expanding sizes and increasing complexity of large astronomical observatories on remote observing sites, the call for an efficient and recourses saving maintenance concept becomes louder. The increasing number of subsystems on telescopes and instruments forces large observatories, like in industries, to rethink conventional maintenance strategies for reaching this demanding goal. The implementation of full-, or semi-automatic processes for standard service activities can help to keep the number of operating staff on an efficient level and to reduce significantly the consumption of valuable consumables or equipment. In this contribution we will demonstrate on the example of the 80 Cryogenic subsystems of the ALMA Front End instrument, how an implemented automatic service process increases the availability of spare parts and Line Replaceable Units. Furthermore how valuable staff recourses can be freed from continuous repetitive maintenance activities, to allow focusing more on system diagnostic tasks, troubleshooting and the interchanging of line replaceable units. The required service activities are decoupled from the day-to-day work, eliminating dependencies on workload peaks or logistic constrains. The automatic refurbishing processes running in parallel to the operational tasks with constant quality and without compromising the performance of the serviced system components. Consequentially that results in an efficiency increase, less down time and keeps the observing schedule on track. Automatic service processes in combination with proactive maintenance concepts are providing the necessary flexibility for the complex operational work structures of large observatories. The gained planning flexibility is allowing an optimization of operational procedures and sequences by considering the required cost efficiency.

Successful strategies to increase the consumption of fruits and vegetables: results from the Danish '6 a day' Work-site Canteen Model Study

DEFF Research Database (Denmark)

Lassen, Anne Dahl; Thorsen, Anne Vibeke; Trolle, Ellen

2004-01-01

Objective: To investigate changes in the consumption of fruits and vegetables in work-site canteens using the tools of continuous quality improvement, and to gain knowledge of practical strategies being effective in increasing the consumption. Design: Study design included baseline data collection...... per lunch meal served per customer (net weight; potatoes not included). Setting: Five workplaces in Denmark: a military base, an electronic component distributor, a bank, a town hall and a waste-handling facility. Subjects: Work-site canteen managers, staff and customers. Results: There were...

Evaluation of JULES-crop performance against site observations of irrigated maize from Mead, Nebraska

OpenAIRE

Williams, Karina; Gornall, Jemma; Harper, Anna; Wiltshire, Andy; Hemming, Debbie; Quaife, Tristan; Arkebauer, Tim; Scoby, David

2016-01-01

The JULES-crop model (Osborne et al., 2015) is a parameterisation of crops within the Joint UK Land Environment Simulator (JULES), which aims to simulate both the impact of weather and climate on crop productivity and the impact of crop-lands on weather and climate. In this evaluation paper, observations of maize at three FLUXNET sites in Nebraska (US-Ne1, US-Ne2, US-Ne3) are used to test model assumptions and make appropriate input parameter choices. JULES runs are performed for the irrigate...

3D representation of geological observations in underground mine workings of the Upper Silesian Coal Basin

Directory of Open Access Journals (Sweden)

Marek Marcisz

Full Text Available The purpose of the paper is to present the possibilities of the three-dimensional representation of geological strata in underground (access workings in a hard coal deposit in the SW part of the Upper Silesian Coal Basin, using CAD software and its flagship program AutoCAD. The 3D visualization of the results of underground workings’ mapping is presented and illustrated on two opening out workings (descending galleries. The criteria for choosing these workings were based on their length and the complexity of geological settings observed while they were driven. The described method may be applied in spatial visualization of geological structures observed in other deposits, mines and existing workings (it is not applicable for designing mine workings, also beyond the area of the Upper Silesian Coal Basin (USCB. The method presented describes the problem of the visualization of underground mine workings in a typical geological aspect, considering (aimed at detailed visualization of geological settings revealed on the side walls of workings cutting the deposit. Keywords: Upper silesian coal basin, Hard coal, Underground mine workings, 3D visualization, CAD

Strategies in disability management. Corporate disability management programs implemented at the work site.

Science.gov (United States)

Kalina, C M

1999-10-30

Managers are challenged to demonstrate all programs as economically essential to the business, generating an appreciable return on investment. Further challenge exists to blend and integrate clinical and business objectives in program development. Disability management programs must be viewed as economically essential to the financial success of the business to assure management support for clinical interventions and return-to-work strategies essential for a successful program. This paper discusses a disability management program integrating clinical and business goals and objectives in return-to-work strategies to effect positive clinical, social-cultural, and business results. Clinical, educational, social, and economic challenges in the development, implementation, and continued management of a disability program at a large corporation with multiple global work sites are defined. Continued discussion addresses the effective clinical interventions and educational strategies utilized successfully within the workplace environment in response to each defined challenge. A multiple disciplinary team approach, clinical and business outcome measures, and quality assurance indicators are discussed as major program components. This article discusses a successful program approach focusing on business process and methodology. These parameters are used to link resources to strategy, developing a product for implementing and managing a program demonstrating economic value added through effective clinical medical case management.

Pitch angle distributions of electrons at dipolarization sites during geomagnetic activity: THEMIS observations

Science.gov (United States)

Wang, Kaiti; Lin, Ching-Huei; Wang, Lu-Yin; Hada, Tohru; Nishimura, Yukitoshi; Turner, Drew L.; Angelopoulos, Vassilis

2014-12-01

Changes in pitch angle distributions of electrons with energies from a few eV to 1 MeV at dipolarization sites in Earth's magnetotail are investigated statistically to determine the extent to which adiabatic acceleration may contribute to these changes. Forty-two dipolarization events from 2008 and 2009 observed by Time History of Events and Macroscale Interactions during Substorms probes covering the inner plasma sheet from 8 RE to 12 RE during geomagnetic activity identified by the AL index are analyzed. The number of observed events with cigar-type distributions (peaks at 0° and 180°) decreases sharply below 1 keV after dipolarization because in many of these events, electron distributions became more isotropized. From above 1 keV to a few tens of keV, however, the observed number of cigar-type events increases after dipolarization and the number of isotropic events decreases. These changes can be related to the ineffectiveness of Fermi acceleration below 1 keV (at those energies, dipolarization time becomes comparable to electron bounce time). Model-calculated pitch angle distributions after dipolarization with the effect of betatron and Fermi acceleration tested indicate that these adiabatic acceleration mechanisms can explain the observed patterns of event number changes over a large range of energies for cigar events and isotropic events. Other factors still need to be considered to assess the observed increase in cigar events around 2 keV. Indeed, preferential directional increase/loss of electron fluxes, which may contribute to the formation of cigar events, was observed. Nonadiabatic processes to accelerate electrons in a parallel direction may also be important for future study.

International workshop on site investigation and evaluation based on the siting process in Sweden

International Nuclear Information System (INIS)

Andersson, Johan; Stroem, A.

2001-06-01

SKB's goal is to commence surface based site investigations in 2002. Extensive preparations are now being made for this transition to the next phase in the siting process for the deep repository for spent nuclear fuel. The purpose of the international workshop on site characterisation held at Aespoe April 2001 was to: present the SKB site investigation and evaluation programme to a group of international experts; discuss whether the available toolbox of investigation methods for surface based site investigations is appropriate and state-of-the-art in an international perspective; and by working group sessions discuss the level of ambition in the programme for site investigation for each discipline. This report summarises the conclusions of the workshop in general terms. Many of the detailed comments and ideas obtained at the workshop have already inspired and will also directly inspire the on-going planning work for site characterisation. The core activity at the workshop was the work performed by working groups. They addressed what should be considered for a site characterisation programme, based on the generic planning made so far by SKB. The working groups also outlined site specific characterisation programmes for the sites suggested by SKB. The tasks were strictly confined to technical and scientific modelling issues. The working group chairmen presented the working group results at the workshop and have also submitted short memos to SKB. The present document is a compilation of these memos. The SKB generic programme as presented in the existing top level documents, 'Requirements and Criteria and Overall Programme', received general endorsement and was appreciated for being comprehensive and systematic. For example, it contains comprehensive lists of parameters to be measured. However, there is need for prioritisation and sequencing. This is actually included in the current planning process at SKB where the generic programme later this year will be adapted to

Observations of Martian surface winds at the Viking Lander 1 site

International Nuclear Information System (INIS)

Murphy, J.R.; Leovy, C.B.; Tillman, J.E.

1990-01-01

Partial failure of the wind instrumentation on the Viking Lander 1 (VL1) in the Martian subtropics (22.5 degree N) has limited previous analyses of meteorological data for this site. The authors describe a method for reconstructing surface winds using data from the partially failed sensor and present and analyze a time series of wind, pressure, and temperature at the site covering 350 Mars days (sols). At the beginning of the mission during early summer, winds were controlled by regional topography, but they soon underwent a transition to a regime controlled by the Hadley circulation. Diurnal and semidiurnal wind oscillations and synoptic variations have been analyzed and compared with the corresponding variations at the Viking Lander 2 middle latitude site (48 degree N). Diurnal wind oscillations were controlled primarily by regional topography and boundary layer forcing, although a global mode may have been influencing them during two brief episodes. Semidiurnal wind oscillations were controlled by the westward propagating semidiurnal tide from sol 210 onward. Comparison of the synoptic variations at the two sites suggests that the same eastward propagating wave trains were present at both sites, at least following the first 1977 great dust storm, but discordant inferred zonal wave numbers and phase speeds at the two sites cast doubt on the zonal wave numbers deduced from analyses of combined wind and pressure data, particularly at the VL1 site where the signal to noise ratio of the dominant synoptic waves is relatively small

Quality assurance of construction work on Dukovany nuclear power plant site

International Nuclear Information System (INIS)

Lachs, W.

1983-01-01

In order to eliminate the effects of the shrinking of concrete of the 150x70 m 2 bed slab 1 m thick, the slab was divided into 36 segments. The side walls were made of steel wire netting and the segments were concreted using the chessboard method. The second concreting was made only after the volume changes in the first concrete layer terminated. The density of the concrete of the shielding was controlled using routine methods as well as a radiometric densimeter which may be used on the building site, the technological procedure was checked by ultrasound, the surface of the concrete structures designed for epoxy coatings must be even and of uniform grain size. Volume moisture of the bed slab must be less than 4% and temperature lower than 10 degC. All deliveries, assembly and construction work must have a certificate of quality awarded after thorough tests and verification. (E.S.)

Conservation implications for the Himalayan wolf Canis (lupus) himalayensis based on observations of packs and home sites in Nepal

OpenAIRE

Werhahn, G; Kusi, N; Sillero-Zubiri, C; Macdonald, DW

2017-01-01

We provide insights into pack composition and den site parameters of the Himalayan wolf Canis (lupus) himalayensis based on observations of free-ranging wolves in three study areas in Nepal. We combine this with a social survey of the local Buddhist communities regarding human–carnivore conflict, to draw inferences for conservation practice in the Nepalese Himalayas. We recorded eight wolf packs (with an average composition of two adults and three pups), and found five home sites in high-alti...

Work and safety managements for on-site installation, commissioning, tests by EU of quench protection circuits for JT-60SA

International Nuclear Information System (INIS)

Yamauchi, Kunihito; Okano, Jun; Shimada, Katsuhiro; Ohmori, Yoshikazu; Terakado, Tsunehisa; Matsukawa, Makoto; Koide, Yoshihiko; Kobayashi, Kazuhiro; Ikeda, Yoshitaka; Fukumoto, Masahiro; Kushita, Kouhei N.

2016-03-01

The superconducting Satellite Tokamak machine “JT-60SA” under construction in Naka Fusion Institute is an international collaborative project between Japan Atomic Energy Agency (JAEA) as the Implementing Agency (IA) of Japan (JA) and Fusion for Energy (F4E) as the IA of Europe (EU). The contributions for this project are based on the supply of components, and thus European manufacturer shall conduct the installation, commissioning and tests on Naka site under the general supervision by F4E via the designated institute in each EU nation. This means that JAEA had an issue to manage the works by European workers and their safety although there is no direct contract. This report describes the approaches for the work and safety managements, which were agreed with EU after the negotiation, and the completed on-site works for Quench Protection Circuits (QPC) as the first experience for EU in JT-60SA project. (author)

KSC Press Site Transformer Bldg. (K7-1205c) SWMU 074 Interim Measure Work Plan

Science.gov (United States)

Starr, A. Scott; Applegate, Joe

2014-01-01

This document presents and discusses the Interim Measure (IM) Work Plan for the Press Site Transformer Building (K7-1205C). The purpose of the proposed IM activities is to remove soil affected with polychlorinated biphenyls (PCBs) greater than the Florida Department of Environmental Protection (FDEP) residential direct-exposure Soil Cleanup Target Level (R-SCTL) of 0.5 milligrams per kilogram and encapsulate concrete exhibiting PCB concentration greater than the Toxic Substance Control Act (TSCA) threshold of 50 milligrams per kilogram.

Remedial investigation/feasibility study work plan for the 100-BC-5 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-07-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). The Tri-Party Agreement requires that the cleanup programs at the Hanford Site integrate the requirements of CERCLA, RCRA, and Washington State's dangerous waste (the state's RCRA-equivalent) program. This work plan and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the CERCLA remedial investigation/feasibility study (RI/FS) for the 100-BC-5 operable unit. The 100-B/C Area consists of the 100-BC-5 groundwater operable unit and four source operable units. The 100-BC-5 operable unit includes all contamination found in the aquifer soils and water beneath the 100-B/C Area. Source operable units include facilities and unplanned release sites that are potential sources of contamination

Protection of SAAO observing site against light and dust pollution

Science.gov (United States)

Sefako, Ramotholo; Väisänen, Petri

2016-10-01

The South African Astronomical Observatory (SAAO) observing station near Sutherland, Northern Cape in South Africa, is one of the darkest sites in the world for optical and IR astronomy. The SAAO hosts and operates several facilities, including the Southern African Large Telescope (SALT) and a number of international robotic telescopes. To ensure that the conditions remain optimal for astronomy, legislation called the Astronomy Geographic Advantage (AGA) Act, of 2007, was enacted. The Act empowers the Department of Science and Technology (DST) to regulate issues that pose a threat to optical and/or radio astronomy in areas declared Astronomy Advantage Areas in South Africa. For optical astronomy, the main challenges are those posed by light and dust pollution as result of wind energy developments, and petroleum gas and oil exploration/exploitation in the area. We give an update of possible threats to the quality of the night skies at SAAO, and the challenges relating to the AGA Act implementation and enforcement. We discuss measures that are put in place to protect the Observatory, including a study to quantify the threat by a planned wind energy facility.

Occurrence of blowing snow events at an alpine site over a 10-year period: Observations and modelling

Science.gov (United States)

Vionnet, V.; Guyomarc'h, G.; Naaim Bouvet, F.; Martin, E.; Durand, Y.; Bellot, H.; Bel, C.; Puglièse, P.

2013-05-01

Blowing snow events control the evolution of the snow pack in mountainous areas and cause inhomogeneous snow distribution. The goal of this study is to identify the main features of blowing snow events at an alpine site and assess the ability of the detailed snowpack model Crocus to reproduce the occurrence of these events in a 1D configuration. We created a database of blowing snow events observed over 10 years at our experimental site. Occurrences of blowing snow events were divided into cases with and without concurrent falling snow. Overall, snow transport is observed during 10.5% of the time in winter and occurs with concurrent falling snow 37.3% of the time. Wind speed and snow age control the frequency of occurrence. Model results illustrate the necessity of taking the wind-dependence of falling snow grain characteristics into account to simulate periods of snow transport and mass fluxes satisfactorily during those periods. The high rate of false alarms produced by the model is investigated in detail for winter 2010/2011 using measurements from snow particle counters.

RCRA facility investigation/corrective measures study work plan for the 100-HR-1 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-09-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US. Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Under the Hanford Federal Facility Agreement and Consent Order, signed by the Washington State Department of Ecology (Ecology), EPA, and the US Department of Energy (DOE), more than 1,000 inactive waste disposal and unplanned release sites on the Hanford Site have been grouped into a number of source and groundwater operable units. These operable units contain contamination in the form of hazardous waste, radioactive/hazardous mixed waste, and other CERCLA hazardous substances. This work plan and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the RCRA facility investigation/corrective measures study (RFI/CMS) for the 100-HR-1 source operable unit. Source operable units include facilities and unplanned release sites that are potential sources of contamination. The 100-HR-3 operable unit underlies the D/DR and H Areas, the 600 Area between them, and the six source operable units these areas contain. The 100-HR-3 operable unit includes all contamination found in the aquifer soils and water within its boundary. Separate work plans have been initiated for the 100-HR-3 groundwater operable unit (DOE-RL 1992a) and the 100-DR-1 (DOE-RL 1992b) source operable units

Evaluation of the state of stress at the Forsmark site. Preliminary site investigation Forsmark area - version 1.2

Energy Technology Data Exchange (ETDEWEB)

Sjoeberg, Jonny; Lindfors, Ulf; Perman, Fredrik; Ask, Daniel [SwedPower AB, Stockholm (Sweden)

2005-09-15

of a hollow core. Having two observations of different core geometries can significantly increase the accuracy in stress estimation from core discing observations. However, the uncertainties associated with the methodology for using core discing observations to estimate stresses must be considered. Additional work to verify this approach would be beneficial for an improved stress estimate at Forsmark. Hydraulic measurements (primarily HTPF) should be planned following overcoring measurements, to complement the stress assessment and resolve any remaining issues. An integrated stress determination using inversion analysis for both overcoring and hydraulic data should also be considered for the site. A new approach for stress modelling is proposed, in which the boundary conditions of a numerical stress model are calibrated in an objective manner to individual or groups of stress measurements, without excluding any data a priori.

Evaluation of the state of stress at the Forsmark site. Preliminary site investigation Forsmark area - version 1.2

International Nuclear Information System (INIS)

Sjoeberg, Jonny; Lindfors, Ulf; Perman, Fredrik; Ask, Daniel

2005-09-01

significantly increase the accuracy in stress estimation from core discing observations. However, the uncertainties associated with the methodology for using core discing observations to estimate stresses must be considered. Additional work to verify this approach would be beneficial for an improved stress estimate at Forsmark. Hydraulic measurements (primarily HTPF) should be planned following overcoring measurements, to complement the stress assessment and resolve any remaining issues. An integrated stress determination using inversion analysis for both overcoring and hydraulic data should also be considered for the site. A new approach for stress modelling is proposed, in which the boundary conditions of a numerical stress model are calibrated in an objective manner to individual or groups of stress measurements, without excluding any data a priori

Low-level waste disposal site selection demonstration

International Nuclear Information System (INIS)

Rogers, V.C.

1984-01-01

This paper discusses the results of recent studies undertaken at EPRI related to low-level waste disposal technology. The initial work provided an overview of the state of the art including an assessment of its influence upon transportation costs and waste form requirements. The paper discusses work done on the overall system design aspects and computer modeling of disposal site performance characteristics. The results of this analysis are presented and provide a relative ranking of the importance of disposal parameters. This allows trade-off evaluations to be made of factors important in the design of a shallow land burial facility. To help minimize the impact of a shortage of low-level radioactive waste disposal sites, EPRI is closely observing the development of bellweather projects for developing new sites. The purpose of this activity is to provide information about lessons learned in those projects in order to expedite the development of additional disposal facilities. This paper describes most of the major stems in selecting a low-level radioactive waste disposal site in Texas. It shows how the Texas Low-Level Radioactive Waste Disposal Authority started with a wide range of potential siting areas in Texas and narrowed its attention down to a few preferred sites. The parameters used to discriminate between large areas of Texas and, eventually, 50 candidate disposal sites are described, along with the steps in the process. The Texas process is compared to those described in DOE and EPRI handbooks on site selection and to pertinent NRC requirements. The paper also describes how an inventory of low-level waste specific to Texas was developed and applied in preliminary performance assessments of two candidate sites. Finally, generic closure requirements and closure operations for low-level waste facilities in arid regions are given

Learning Spaces and Collaborative Work: Barriers or Supports?

Science.gov (United States)

King, Hayley

2016-01-01

Drawing on 18 months of fieldwork, this article discusses the use of physical, virtual and social space to support collaborative work in translator education programs. The study adopted a contrastive ethnography approach that incorporated single- and multiple-case design rationales for site selection. Extended observation, informal chats and…

A multilevel study on the association of observer-assessed working conditions with depressive symptoms among female eldercare workers from 56 work units in 10 care homes in Denmark

Science.gov (United States)

Jakobsen, Louise M; Jorgensen, Anette F B; Thomsen, Birthe L; Greiner, Birgit A; Rugulies, Reiner

2015-01-01

Objectives Eldercare workers in Denmark have a higher prevalence of poor psychological health than other occupational groups. We examined the association between working conditions assessed by trained observers and depressive symptoms assessed by self-report in a study of female Danish eldercare workers. Methods Working conditions were observed based on action regulation theory and defined as (1) regulation requirements, a workplace resource providing opportunity for decision-making and skill development and (2) barriers for task completion. We examined the associations of individual and work unit averaged working conditions with depressive symptoms in a sample of 95 individually observed eldercare workers. Further, we examined the association of work unit averaged working conditions with depressive symptoms in a sample of 205 care workers, including both observed and non-observed individuals. We used regression models that allowed for correlations within work units and care homes and adjusted these models for demographics, job characteristics and stressful life events. Results Higher levels of regulation requirements were associated with lower depressive symptoms at the individual level (p=0.04), but not at the workplace level. Barriers were not associated with depressive symptoms at the individual level. At the workplace level, a higher number of qualitatively different barriers (p=0.04) and a higher number of barriers for equipment use (p=0.03) were associated with lower levels of depressive symptoms in the age and cohabitation adjusted model, however statistical significance was lost in the fully adjusted model. Conclusions Low level of regulation requirements was associated with a high level of depressive symptoms. The study highlights the importance of examining both individual and workplace levels of working conditions. PMID:26560058

A multilevel study on the association of observer-assessed working conditions with depressive symptoms among female eldercare workers from 56 work units in 10 care homes in Denmark

DEFF Research Database (Denmark)

Jakobsen, Louise M.; Jorgensen, Anette F. B.; Thomsen, Birthe L.

2015-01-01

-observed individuals. We used regression models that allowed for correlations within work units and care homes and adjusted these models for demographics, job characteristics and stressful life events. RESULTS: Higher levels of regulation requirements were associated with lower depressive symptoms at the individual......OBJECTIVES: Eldercare workers in Denmark have a higher prevalence of poor psychological health than other occupational groups. We examined the association between working conditions assessed by trained observers and depressive symptoms assessed by self-report in a study of female Danish eldercare...... workers. METHODS: Working conditions were observed based on action regulation theory and defined as (1) regulation requirements, a workplace resource providing opportunity for decision-making and skill development and (2) barriers for task completion. We examined the associations of individual and work...

Final work plan: Expedited Site Characterization of the IES Industries, Inc., Site at Marshalltown, Iowa. Ames Expedited Site Characterization Project, Version 1.0

Energy Technology Data Exchange (ETDEWEB)

1994-04-04

The overall goal of the Ames Laboratory Expedited Site Characterization (ESC) project is to evaluate and promote both innovative and state-of-the-practice site characterization and/or monitoring technologies. This will be accomplished by fielding both types of technologies together in the context of an expedited site characterization. The first site will be at a former manufactured gas plant (FMGP) in Marshalltown, Iowa. The project will field three areas of technology: geophysical, analytical, and data fusion. Geophysical technologies are designed to understand the subsurface geology to help predict fate and transport of the target contaminants. Analytical technologies/methods are designed to detect and quantify the target contaminants. Data fusion technology consists of software systems designed to rapidly integrate or fuse all site information into a conceptual site model that then becomes the decision making tool for the site team to plan subsequent sampling activity. Not all of the contaminants present can be located at the action level. Polynuclear aromatic hydrocarbons (PAHs) are the signature organics associated with the coal tar activities that took place at the site. As a result, PAHs were selected as the target compounds. Screening analytical instruments and nonintrusive geophysical techniques will be fielded to qualitatively map the spatial contaminant distribution. Soil gas surveys, immunoassay testing (IMA), innovative optical techniques, and passive organic sorbent sensors will be deployed along with the geophysical methods. Gas chromatography/mass spectrometry (GC/MS) instruments and a cone penetrometer system equipped with a laser-induced fluorescence (LIF) probe will quantitatively map the action level edges of the PAH plume(s). Samples will be taken both by the cone penetrometer test system (CPT) and the Geoprobe {reg_sign} sampler system.

Working group 4b: Regional aspects. Siting in Walloon region and offshore

International Nuclear Information System (INIS)

Wilmes, Ph.; Fincoeur, P.; Slegers, G.

1976-01-01

Four nuclear power plant solutions in view of siting have been considered. a) Saturation of the existing sites. The only site considered is Tihange where a 870 MWe power plant is operated and a 930 MWe is under construction. b) Creation of new sites only for the production of electrical power and/or thermal energy. There are two possibilities: the creation of a new site for big power stations on the Meuse river and the spreading of power plants of two kinds: supply of electricity only and double purpose production: vapor/electricity or heat/electricity. c) Creation of complete sites for the transformation of nuclear material: enrichment of fissile material; fuel elements fabrication, burning, spent fuel reprocessing and waste management. d) Off-shore power plant siting and the creation of an artificial island. (A.F.)

Geoscientific evaluation factors and criteria for siting and site evaluation. Progress report

International Nuclear Information System (INIS)

Stroem, A.; Ericsson, Lars O.; Svemar, C.; Almen, K.E.; Andersson, Johan

1999-03-01

The purposes of the present report are to: present the work that has been done to identify the parameters that need to be determined in a geoscientific site investigation and that serve as the basis for the work with geoscientific evaluation factors; give a progress report from the project that was initiated in 1997 named Siting Factors and Criteria for Site Evaluation, with an emphasis on definitions, outline and structure for the execution of the work; present geoscientific requirements on function both general and in detail in the form of an example for the discipline rock mechanics; present geoscientific evaluation factors associated with different stages in the siting work in the form of an example for the discipline hydrogeochemical composition; present plans for further work as regards criteria for site evaluation in different siting stages. The project is under way, and this is to be regarded as a progress report since e.g. criteria for site evaluation will be presented at a later date. The long-term performance and safety of the deep repository must always be evaluated by means of an integrated safety assessment. The work with factors and criteria can never take the place of such an assessment, but can provide guidance regarding its outcome. Requirements and preferences regarding the function of the rock in the deep repository have been clarified in this progress report. What is new here is the structuring that has been carried out, with a classification into different geoscientific disciplines, and the formalism that has been given to the terms requirement, preference and function. Based on fundamental safety and construction functions, requirements on function have been specified for the disciplines geology, thermal properties, hydro-geology, rock mechanics, chemistry and transport properties. Furthermore, function analyses have been identified by means of which it is possible to concretize requirements on function and which geoscientific parameters are

Geoscientific evaluation factors and criteria for siting and site evaluation. Progress report

Energy Technology Data Exchange (ETDEWEB)

Stroem, A.; Ericsson, Lars O.; Svemar, C. [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Almen, K.E. [KEA GEO-konsult AB (Sweden); Andersson, Johan [Golder Grundteknik KB (Sweden)

1999-03-01

The purposes of the present report are to: present the work that has been done to identify the parameters that need to be determined in a geoscientific site investigation and that serve as the basis for the work with geoscientific evaluation factors; give a progress report from the project that was initiated in 1997 named Siting Factors and Criteria for Site Evaluation, with an emphasis on definitions, outline and structure for the execution of the work; present geoscientific requirements on function both general and in detail in the form of an example for the discipline rock mechanics; present geoscientific evaluation factors associated with different stages in the siting work in the form of an example for the discipline hydrogeochemical composition; present plans for further work as regards criteria for site evaluation in different siting stages. The project is under way, and this is to be regarded as a progress report since e.g. criteria for site evaluation will be presented at a later date. The long-term performance and safety of the deep repository must always be evaluated by means of an integrated safety assessment. The work with factors and criteria can never take the place of such an assessment, but can provide guidance regarding its outcome. Requirements and preferences regarding the function of the rock in the deep repository have been clarified in this progress report. What is new here is the structuring that has been carried out, with a classification into different geoscientific disciplines, and the formalism that has been given to the terms requirement, preference and function. Based on fundamental safety and construction functions, requirements on function have been specified for the disciplines geology, thermal properties, hydro-geology, rock mechanics, chemistry and transport properties. Furthermore, function analyses have been identified by means of which it is possible to concretize requirements on function and which geoscientific parameters are

Impact of gastroesophageal reflux disease on work absenteeism, presenteeism and productivity in daily life: a European observational study.

Science.gov (United States)

Gisbert, Javier P; Cooper, Alun; Karagiannis, Dimitrios; Hatlebakk, Jan; Agréus, Lars; Jablonowski, Helmut; Nuevo, Javier

2009-10-16

The RANGE (Retrospective ANalysis of GastroEsophageal reflux disease [GERD]) study assessed differences among patients consulting a primary care physician due to GERD-related reasons in terms of: symptoms, diagnosis and management, response to treatment, and effects on productivity, costs and health-related quality of life. This subanalysis of RANGE determined the impact of GERD on productivity in work and daily life. RANGE was conducted at 134 primary care sites across six European countries (Germany, Greece, Norway, Spain, Sweden and the UK). All subjects (aged >or=18 years) who consulted with their primary care physician over a 4-month identification period were screened retrospectively, and those consulting at least once for GERD-related reasons were identified (index visit). From this population, a random sample was selected to enter the study and attended a follow-up appointment, during which the impact of GERD on productivity while working (absenteeism and presenteeism) and in daily life was evaluated using the self-reported Work Productivity and Activity Impairment Questionnaire for patients with GERD (WPAI-GERD). Overall, 373,610 subjects consulted with their primary care physician over the 4-month identification period, 12,815 for GERD-related reasons (3.4%); 2678 randomly selected patients attended the follow-up appointment. Average absenteeism due to GERD was highest in Germany (3.2 hours/week) and lowest in the UK (0.4 hours/week), with an average of up to 6.7 additional hours/week lost due to presenteeism in Norway. The average monetary impact of GERD-related work absenteeism and presenteeism were substantial in all countries (from euro55/week per employed patient in the UK to euro273/patient in Sweden). Reductions in productivity in daily life of up to 26% were observed across the European countries. GERD places a significant burden on primary care patients, in terms of work absenteeism and presenteeism and in daily life. The resulting costs to the

Description of Work for Drilling at the 183-DR Site in Support of the In Situ Gaseous Reduction Test

Energy Technology Data Exchange (ETDEWEB)

Thornton, Edward C.; Olsen, Khris B.; Schalla, Ronald

2000-06-26

In Situ Gaseous Reduction is a technology currently being developed by DOE for the remediation of soil waste sites contaminated with hexavalent chromium. Prior work suggests that a candidate for application of this approach is the 183-DR site at Hanford. However, deep vadose zone drilling is needed to verify the presence of a hexavalent chromium source and to determine the concentration levels and spatial distribution of contamination. This document presents the requirements associated with drilling one to two vadose zone boreholes at the 183-DR site to obtain this information. If hexavalent chromium is determined to be present at levels of at least 10 ppm in the vadose zone in one of the initial boreholes, this hole will be completed for gas injection and six additional gas extraction boreholes will be drilled and completed. This network will be used as a flowcell for performing a gas treatment test at the site.

Site preparation works for No.3 plant in Ikata Nuclear Power Station, Shikoku Electric Power Co., Inc

International Nuclear Information System (INIS)

Ishihara, Hisashi; Nakajima, Hiroshi; Oshima, Teruhiko

1986-01-01

Ikata Power Station is only nuclear power station in Shikoku located at the root of Sadamisaki Peninsula. No.1 plant started the operation in September, 1977, and No.2 plant started the operation in March, 1982. By constructing No.3 plant of 890 MWe output, the total power output will be 2.022 million kW. No.3 plant is installed adjacently to No.1 and No.2 plants on their east side. In this place, the existing facilities of the harbor and others can be effectively utilized, the nature of ground is solid, and the fundamental condition of location is perfect, it is easy to obtain the cooperation of local people as No.1 and No.2 plants have been in operation, and it is advantageous in view of the construction period for the power supply plan. The site preparation works have progressed smoothly since the start in June, 1985. About 100,000 m 2 of the site is created by cutting natural ground, and about 54,000 m 2 is created by sea reclamation. About 5 million m 3 of earth and stone generated by cutting and excavation are utilized for reclamation, revetment and others. The topographic and geological features, sea condition, the outline of geological survey, the layout, and the construction works of revetment, cutting, the creation of substitute seaweed farm, appurtenant works, and the measures for environment preservation are described. (Kako, I.)

Concordance between VDU-users' ratings of comfort and perceived exertion with experts' observations of workplace layout and working postures.

Science.gov (United States)

Lindegård, A; Karlberg, C; Wigaeus Tornqvist, E; Toomingas, A; Hagberg, M

2005-05-01

The aim of the present study was to evaluate the concordance (agreement) between VDU-users' ratings of comfort and ergonomists' observations of workplace layout, and the concordance between VDU-users' ratings of perceived exertion and ergonomists' observations of working postures during VDU-work. The study population consisted of 853 symptom free subjects. Data on perceived comfort in different dimensions and data regarding perceived exertion in different body locations were collected by means of a questionnaire. Data concerning workplace layout and working postures were collected with an observation protocol, by an ergonomist. Concordance between ratings of comfort and observations of workplace layout was reasonably good for the chair and the keyboard (0.60, 0.58) and good regarding the screen and the input device (0.72, 0.61). Concordance between ratings of perceived exertion and observations of working postures indicated good agreement (0.63-0.77) for all measured body locations (neck, shoulder, wrist and trunk). In conclusion ratings of comfort and perceived exertion could be used as cost-efficient and user-friendly methods for practitioners to identify high exposure to poor workplace layout and poor working postures.

Work plan for the remedial investigation/feasibility study-environmental impact statement for the Weldon Spring site, Weldon Spring, Missouri

International Nuclear Information System (INIS)

Peterson, J.M.; MacDonell, M.M.; Haroun, L.A.; Nowadly, F.K.; Knight, W.C.; Vajda, G.F.

1988-08-01

The Weldon Spring Site Remedial Action Project is being conducted as a Major System Acquisition under the Surplus Facilities Management Program (SFMP) of the US Department of Energy (DOE). The major goals of the SFMP are to eliminate potential hazards to the public and the environment that are associated with contamination at SFMP sites and to make surplus real property available for other uses to the extent possible. The Weldon Spring site is located near Weldon Spring, Missouri, about 48 km (30 mi) west of St. Louis. It is surrounded by large tracts of land owned by the federal government and the state of Missouri. The site consists of four raffinate pits, an inactive chemical plant, and a contaminated quarry. The raffinate pits and chemical plant are on adjoining land about 3.2 km (2 mi) southwest of the junction of Missouri (State) Route 94 and US Route 40/61, with access from Route 94. The quarry is located in a comparatively remote area about 6.4 km (4 mi) south-southwest of the raffinate pits and chemical plant area; the quarry can also be accessed from Route 94. These areas are fenced and closed to the public. From 1941 to 1944, the US Department of the Army operated the Weldon Spring Ordnance Works, constructed on the land that is now the Weldon Spring site, for production of trinitrotoluene (TNT) and dinitrotoluene (DNT). The Army used the quarry for disposal of rubble contaminated with TNT. In the mid 1950s, 83 ha (205 acres) of the ordnance works property was transferred to the US Atomic Energy Commission (AEC); this is now the raffinate pits and chemical plant area. An additional 6 ha (15 acres) was later transferred to the AEC for expansion of waste storage capacity. 23 refs., 37 figs., 21 tabs

Radionuclide migration in groundwater at a low-level waste disposal site: a comparison of predictive performance modeling versus field observations

International Nuclear Information System (INIS)

Robertson, D.E.; Myers, D.A.; Abel, K.H.; Bergeron, M.P.; Champ, D.R.; Killey, R.W.D.; Moltyaner, G.L.; Young, J.L.

1986-01-01

This paper describes a project which is structured to test the concept of modeling a shallow land low-level waste burial site. The project involves a comparison of the actual observed radionuclide migration in groundwaters at a 30-year old well-monitored field site with the results of predictive transport modeling. The comparison is being conducted as a cooperative program with the Atomic Energy of Canada Ltd. (AECL) at the low-level waste management area at the Chalk River Nuclear Laboratories, Ontario, Canada. A joint PNL-AECL field investigation was conducted in 1983 and 1984 to compliment the existing extensive data base on actual radionuclide migration. Predictive transport modeling is currently being conducted for this site; first, as if it were a new location being considered for a low-level waste shallow-land burial site and only minimal information about the site were available, and second, utilizing the extensive data base available for the site. The modeling results will then be compared with the level of effort needed to reasonably predict the spacial and temporal movement of radionuclides in the groundwater environment

Directional topographic site response at Tarzana observed in aftershocks of the 1994 Northridge, California, earthquake: Implications for mainshock motions

Science.gov (United States)

Spudich, P.; Hellweg, M.; Lee, W.H.K.

1996-01-01

The Northridge earthquake caused 1.78 g acceleration in the east-west direction at a site in Tarzana, California, located about 6 km south of the mainshock epicenter. The accelerograph was located atop a hill about 15-m high, 500-m long, and 130-m wide, striking about N78??E. During the aftershock sequence, a temporary array of 21 three-component geophones was deployed in six radial lines centered on the accelerograph, with an average sensor spacing of 35 m. Station COO was located about 2 m from the accelerograph. We inverted aftershock spectra to obtain average relative site response at each station as a function of direction of ground motion. We identified a 3.2-Hz resonance that is a transverse oscillation of the hill (a directional topographic effect). The top/base amplification ratio at 3.2 Hz is about 4.5 for horizontal ground motions oriented approximately perpendicular to the long axis of the hill and about 2 for motions parallel to the hill. This resonance is seen most strongly within 50 m of COO. Other resonant frequencies were also observed. A strong lateral variation in attenuation, probably associated with a fault, caused substantially lower motion at frequencies above 6 Hz at the east end of the hill. There may be some additional scattered waves associated with the fault zone and seen at both the base and top of the hill, causing particle motions (not spectral ratios) at the top of the hill to be rotated about 20?? away from the direction transverse to the hill. The resonant frequency, but not the amplitude, of our observed topographic resonance agrees well with theory, even for such a low hill. Comparisons of our observations with theoretical results indicate that the 3D shape of the hill and its internal structure are important factors affecting its response. The strong transverse resonance of the hill does not account for the large east-west mainshock motions. Assuming linear soil response, mainshock east-west motions at the Tarzana accelerograph

A system to test the ground surface conditions of construction sites--for safe and efficient work without physical strain.

Science.gov (United States)

Koningsveld, Ernst; van der Grinten, Maarten; van der Molen, Henk; Krause, Frank

2005-07-01

Ground surface conditions on construction sites have an important influence on the health and safety of workers and their productivity. The development of an expert-based "working conditions evaluation" system is described, intended to assist site managers in recognising unsatisfactory ground conditions and remedying these. The system was evaluated in the period 2002-2003. The evaluation shows that companies recognize poor soil/ground conditions as problematic, but are not aware of the specific physical workload hazards. The developed methods allow assessment of the ground surface quality and selection of appropriate measures for improvement. However, barriers exist at present to wide implementation of the system across the industry. Most significant of these is that responsibility for a site's condition is not clearly located within contracting arrangements, nor is it a topic of serious negotiation.

Sprucing up the site - update

CERN Multimedia

2009-01-01

As mentioned in a previous article the Bulletin will be publishing regular short updates following the consolidation work going on around the CERN sites: All internal lighting is being replaced in the office buildings on the Prevessin site. Work has started in building 866 and will move to 864 and 865 later. New energy-efficient lights are being installed, which will reduce electricity consumption by 30 -50%, and in the common areas like corridors the lighting will be switched on by motion sensors. Also in the Prevessin site, the lines in the car parks are being repainted. This will continue in the Meyrin site later. Work has started in Building 30 to completely refurbish the AT Auditorium.

The first direct observation of hydrogen trapping sites in TiC precipitation-hardening steel through atom probe tomography

International Nuclear Information System (INIS)

Takahashi, Jun; Kawakami, Kazuto; Kobayashi, Yukiko; Tarui, Toshimi

2010-01-01

For the first time ever, atomic-scale direct observation of deuterium atoms trapping at nano-sized titanium carbide (TiC) precipitates in steel was successfully achieved using atom probe tomography (APT). Deuterium gas charging into the needle specimen and subsequently quenching were conducted in our designed chamber attached to three-dimensional atom probe (3DAP). The deuterium atoms were definitely observed on the broad surface of TiC platelets, which indicated that the broad interface between the matrix and TiC was the main trapping site.

Promoting Your Web Site.

Science.gov (United States)

Raeder, Aggi

1997-01-01

Discussion of ways to promote sites on the World Wide Web focuses on how search engines work and how they retrieve and identify sites. Appropriate Web links for submitting new sites and for Internet marketing are included. (LRW)

Plantar calcaneal enthesophytes: new observations regarding sites of origin based on radiographic, MR imaging, anatomic, and paleopathologic analysis

International Nuclear Information System (INIS)

Abreu, M.R.; Chung, C.B.; Mendes, L.; Mohana-Borges, A.; Trudell, D.; Resnick, D.

2003-01-01

To determine the relationship between sites of calcaneal plantar enthesophytes and surrounding fascial and soft tissue structures using routine radiography, MR imaging, and data derived from cadaveric and paleopathologic specimens.Design and patients. Two observers analyzed the MR imaging studies of 40 ankles in 38 patients (35 males, 3 females; mean age 48.3 years) with plantar calcaneal enthesophytes that were selected from all the ankle MR examinations performed during the past year. Data derived from these MR examinations were the following: the size of the enthesophyte; its location in relation to the plantar fascia (PF) and flexor muscles; and the thickness and signal of the PF. The corresponding radiographs of the ankles were evaluated at a different time by the same observers for the presence or absence of plantar enthesophytes and, when present, their measurements. A third observer reviewed all the discordant observations of MR imaging and radiographic examinations. Two observers analyzed 22 calcaneal specimens with plantar enthesophytes at an anthropology museum to determine the orientation of each plantar enthesophyte. MR imaging of a cadaveric foot with a plantar enthesophyte with subsequent sagittal sectioning was performed to provide further anatomic understanding.Results. With regard to MR imaging, the mean size of the plantar enthesophytes was 4.41 mm (SD 2.4). Twenty (50%) enthesophytes were located above the PF, 16 (40%) between the fascia and abductor digiti minimi, flexor digitorum brevis and abductor hallucis muscles, and only one (3%) was located within the PF. In three (8%) cases the location was not determined. The size of enthesophytes seen with MR imaging and radiographs was highly correlated (P 0.8, kappa >0.9). Eleven of the 22 bone specimens had plantar enthesophytes oriented in the direction of the abductor digiti minimi and 11 oriented in the direction of the flexor digitorum brevis and PF. The cadaveric sections revealed different

Plantar calcaneal enthesophytes: new observations regarding sites of origin based on radiographic, MR imaging, anatomic, and paleopathologic analysis

Energy Technology Data Exchange (ETDEWEB)

Abreu, M.R.; Chung, C.B.; Mendes, L.; Mohana-Borges, A.; Trudell, D.; Resnick, D. [Department of Radiology, Musculoskeletal Section, VA San Diego Healthcare System, 3350 La Jolla Village Drive, San Diego, CA 92161 (United States)

2003-01-01

To determine the relationship between sites of calcaneal plantar enthesophytes and surrounding fascial and soft tissue structures using routine radiography, MR imaging, and data derived from cadaveric and paleopathologic specimens.Design and patients. Two observers analyzed the MR imaging studies of 40 ankles in 38 patients (35 males, 3 females; mean age 48.3 years) with plantar calcaneal enthesophytes that were selected from all the ankle MR examinations performed during the past year. Data derived from these MR examinations were the following: the size of the enthesophyte; its location in relation to the plantar fascia (PF) and flexor muscles; and the thickness and signal of the PF. The corresponding radiographs of the ankles were evaluated at a different time by the same observers for the presence or absence of plantar enthesophytes and, when present, their measurements. A third observer reviewed all the discordant observations of MR imaging and radiographic examinations. Two observers analyzed 22 calcaneal specimens with plantar enthesophytes at an anthropology museum to determine the orientation of each plantar enthesophyte. MR imaging of a cadaveric foot with a plantar enthesophyte with subsequent sagittal sectioning was performed to provide further anatomic understanding.Results. With regard to MR imaging, the mean size of the plantar enthesophytes was 4.41 mm (SD 2.4). Twenty (50%) enthesophytes were located above the PF, 16 (40%) between the fascia and abductor digiti minimi, flexor digitorum brevis and abductor hallucis muscles, and only one (3%) was located within the PF. In three (8%) cases the location was not determined. The size of enthesophytes seen with MR imaging and radiographs was highly correlated (P<0.01). The interobserver agreement for all measurements was good (Pearson >0.8, kappa >0.9). Eleven of the 22 bone specimens had plantar enthesophytes oriented in the direction of the abductor digiti minimi and 11 oriented in the direction of the

Site locality identification study: Hanford Site. Volume II. Data cataloging

International Nuclear Information System (INIS)

1980-07-01

Data compilation and cataloging for the candidate site locality identification study were conducted in order to provide a retrievable data cataloging system for the present siting study and future site evaluation and licensng processes. This task occurred concurrently with and also independently of other tasks of the candidate site locality identification study. Work in this task provided the data utilized primarily in the development and application of screening and ranking processes to identify candidate site localities on the Hanford Site. The overall approach included two steps: (1) data acquisition and screening; and (2) data compilation and cataloging. Data acquisition and screening formed the basis for preliminary review of data sources with respect to their probable utilization in the candidate site locality identification study and review with respect to the level of completeness and detail of the data. The important working assumption was that the data to be used in the study be based on existing and available published and unpublished literature. The data compilation and cataloging provided the basic product of the Task; a retrievable data cataloging system in the form of an annotated reference list and key word index and an index of compiled data. The annotated reference list and key word index are cross referenced and can be used to trace and retrieve the data sources utilized in the candidate site locality identification study

Organization and methodology approach for the safety assessment of the present situation and the future works on Chernobyl-4 and the site

International Nuclear Information System (INIS)

Bachner, D.; Benoist, E.; Duco, J.; Jahns, A.

1995-01-01

This work deals with the organization and methodology approach for the safety assessment of the present situation and the future works on Chernobyl 4 and the site. It presents the results of a common preliminary discussion in order to formulate advices on the basic management of the Chernobyl safety assessment process. (O.L.)

Reactive sites influence in PMMA oligomers reactivity: a DFT study

Science.gov (United States)

Paz, C. V.; Vásquez, S. R.; Flores, N.; García, L.; Rico, J. L.

2018-01-01

In this work, we present a theoretical study of methyl methacrylate (MMA) living anionic polymerization. The study was addressed to understanding two important experimental observations made for Michael Szwarc in 1956. The unexpected effect of reactive sites concentration in the propagation rate, and the self-killer behavior of MMA (deactivating of living anionic polymerization). The theoretical calculations were performed by density functional theory (DFT) to obtain the frontier molecular orbitals values. These values were used to calculate and analyze the chemical interaction descriptors in DFT-Koopmans’ theorem. As a result, it was observed that the longest chain-length species (related with low concentration of reactive sites) exhibit the highest reactivity (behavior associated with the increase of the propagation rate). The improvement in this reactivity was attributed to the crosslinking produced in the polymethyl methacrylate chains. Meanwhile, the self-killer behavior was associated with the intermolecular forces present in the reactive sites. This behavior was associated to an obstruction in solvation, since the active sites remained active through all propagation species. The theoretical results were in good agreement with the Szwarc experiments.

Remedial investigation/feasibility study work plan for the 100-KR-4 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-09-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). This work plan and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the CERCLA remedial investigation/feasibility study (RI/FS) for the 100-KR-4 operable unit. The 100-K Area consists of the 100-KR-4 groundwater operable unit and three source operable units. The 100-KR-4 operable unit includes all contamination found in the aquifer soils and water beneath the 100-K Area. Source operable units include facilities and unplanned release sites that are potential sources of contamination

Remedial investigation/feasibility study work plan for the 100-KR-4 operable unit, Hanford Site, Richland, Washington

Energy Technology Data Exchange (ETDEWEB)

1992-09-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US Environmental Protection Agency`s (EPA`s) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). This work plan and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the CERCLA remedial investigation/feasibility study (RI/FS) for the 100-KR-4 operable unit. The 100-K Area consists of the 100-KR-4 groundwater operable unit and three source operable units. The 100-KR-4 operable unit includes all contamination found in the aquifer soils and water beneath the 100-K Area. Source operable units include facilities and unplanned release sites that are potential sources of contamination.

Safety Oversight of Decommissioning Activities at DOE Nuclear Sites

International Nuclear Information System (INIS)

Zull, Lawrence M.; Yeniscavich, William

2008-01-01

The Defense Nuclear Facilities Safety Board (Board) is an independent federal agency established by Congress in 1988 to provide nuclear safety oversight of activities at U.S. Department of Energy (DOE) defense nuclear facilities. The activities under the Board's jurisdiction include the design, construction, startup, operation, and decommissioning of defense nuclear facilities at DOE sites. This paper reviews the Board's safety oversight of decommissioning activities at DOE sites, identifies the safety problems observed, and discusses Board initiatives to improve the safety of decommissioning activities at DOE sites. The decommissioning of former defense nuclear facilities has reduced the risk of radioactive material contamination and exposure to the public and site workers. In general, efforts to perform decommissioning work at DOE defense nuclear sites have been successful, and contractors performing decommissioning work have a good safety record. Decommissioning activities have recently been completed at sites identified for closure, including the Rocky Flats Environmental Technology Site, the Fernald Closure Project, and the Miamisburg Closure Project (the Mound site). The Rocky Flats and Fernald sites, which produced plutonium parts and uranium materials for defense needs (respectively), have been turned into wildlife refuges. The Mound site, which performed R and D activities on nuclear materials, has been converted into an industrial and technology park called the Mound Advanced Technology Center. The DOE Office of Legacy Management is responsible for the long term stewardship of these former EM sites. The Board has reviewed many decommissioning activities, and noted that there are valuable lessons learned that can benefit both DOE and the contractor. As part of its ongoing safety oversight responsibilities, the Board and its staff will continue to review the safety of DOE and contractor decommissioning activities at DOE defense nuclear sites

Study of site layout in the Rokkasho site

International Nuclear Information System (INIS)

Sato, Kazuyoshi; Tamura, Kousaku; Yagenji, Akira; Sekiya, Shigeki; Takahashi, Hideo; Neyatani, Yuzuru; Uehara, Masaharu; Motohashi, Keiichi; Hashimoto, Masayoshi; Ogino, Shunji; Nagamatsu, Nobuhide

2006-03-01

The Final Design Report (FDR) of the International Thermonuclear Experimental Reactor (ITER) was published on July 2001 as a summary of the Engineering Design Activity (EDA). After the EDA, site dependent design has been investigated for the invitation of ITER toward Rokkasho Site (Iyasakadai area) in Aomori prefecture. This report describes the results of site layout of major buildings and structures of ITER in the Rokkasho-Site. The data of the ground near the site and the results of site dependent design in Japan were applied to this study. Through this study, the most appropriate site layout has been constructed with satisfaction of following conditions. (1) Bedrock level at the tokamak complex building is relatively high and it can be reduced the cost of excavation and foundation work. (2) Total amount of excavation soil for site preparation is minimized and the flexibility of the layout is ensured with flat ground level. (3) Accessibility of human and equipments, reduction of noise and vibration to the environment can be obtained. Total length of ducts and piping between buildings in site is minimized. (author)

Site description of Laxemar at completion of the site investigation phase. SDM-Site Laxemar

Energy Technology Data Exchange (ETDEWEB)

2009-12-15

the waning stages of the Svecokarelian orogeny. The candidate area is circular-shaped with an area of 54 km2, and hosts the Laxemar subarea in its eastern part. The south-western part of the Laxemar subarea was selected as the focused area for the complete site investigation work, following the initial investigations at the site. Prior to the presentation of the SDM-Site report, three versions of a site descriptive model have been completed for the Laxemar-Simpevarp area and subjected to peer review. The last version, referred to as version Laxemar 1.2, constituted a preliminary site description that concluded the initial site investigation work and was presented in 2006. This preliminary site description formed the basis for a preliminary safety evaluation (PSE) of the Laxemar subarea, a preliminary repository layout, and the first evaluation of the long-term safety of this layout for a KBS-3 repository in the context of the SR-Can project. The final site descriptive model, SDM-Site Laxemar, builds on a coordinated geological model in 3D, into which other discipline-specific models have been integrated without any major conflicting interpretations. In particular, the bedrock thermal and strength properties of the bedrock at the site have been coupled to lithology and identified rock domains in the geological model and an integrated description has been devised that links the hydrogeology and the chemistry of the groundwater to hydraulic conductor domains (deformation zones) and hydraulic rock domains (and underlying fracture domains) and their division in depth zones. These mutually consistent results demonstrate that a fundamental understanding of the current state, properties and processes in Laxemar, from the surface down to potential repository depth, has been achieved. In addition, the properties of the area can be explained in the context of an understanding of its past evolution, throughout a long period of geological history. This integrated understanding of

Site description of Laxemar at completion of the site investigation phase. SDM-Site Laxemar

International Nuclear Information System (INIS)

2009-12-01

the waning stages of the Svecokarelian orogeny. The candidate area is circular-shaped with an area of 54 km 2 , and hosts the Laxemar subarea in its eastern part. The south-western part of the Laxemar subarea was selected as the focused area for the complete site investigation work, following the initial investigations at the site. Prior to the presentation of the SDM-Site report, three versions of a site descriptive model have been completed for the Laxemar-Simpevarp area and subjected to peer review. The last version, referred to as version Laxemar 1.2, constituted a preliminary site description that concluded the initial site investigation work and was presented in 2006. This preliminary site description formed the basis for a preliminary safety evaluation (PSE) of the Laxemar subarea, a preliminary repository layout, and the first evaluation of the long-term safety of this layout for a KBS-3 repository in the context of the SR-Can project. The final site descriptive model, SDM-Site Laxemar, builds on a coordinated geological model in 3D, into which other discipline-specific models have been integrated without any major conflicting interpretations. In particular, the bedrock thermal and strength properties of the bedrock at the site have been coupled to lithology and identified rock domains in the geological model and an integrated description has been devised that links the hydrogeology and the chemistry of the groundwater to hydraulic conductor domains (deformation zones) and hydraulic rock domains (and underlying fracture domains) and their division in depth zones. These mutually consistent results demonstrate that a fundamental understanding of the current state, properties and processes in Laxemar, from the surface down to potential repository depth, has been achieved. In addition, the properties of the area can be explained in the context of an understanding of its past evolution, throughout a long period of geological history. This integrated understanding

Underwater and Dive Station Work-Site Noise Surveys

National Research Council Canada - National Science Library

Wolgemuth, Keith S; Cudahy, Edward A; Schwaller, Derek W

2008-01-01

Previous work performed by the Naval Submarine Medical Research Laboratory (NSMRL) had developed in-water permissible continuous noise exposure guidance Work performed by the Navy Experimental Diving Unit...

Work plan for defining a standard inventory estimate for wastes stored in Hanford Site underground tanks

International Nuclear Information System (INIS)

Hodgson, K.M.

1996-01-01

This work plan addresses the Standard Inventory task scope, deliverables, budget, and schedule for fiscal year 1997. The goal of the Standard Inventory task is to resolve differences among the many reported Hanford Site tank waste inventory values and to provide inventory estimates that will serve as Standard Inventory values for all waste management and disposal activities. These best-basis estimates of chemicals and radionuclides will be reported on both a global and tank-specific basis and will be published in the Tank Characterization Database

Low prevalence of work disability in early inflammatory arthritis (EIA) and early rheumatoid arthritis at enrollment into a multi-site registry: results from the catch cohort.

Science.gov (United States)

Mussen, Lauren; Boyd, Tristan; Bykerk, Vivian; de Leon, Faye; Li, Lihua; Boire, Gilles; Hitchon, Carol; Haraoui, Boulos; Thorne, J Carter; Pope, Janet

2013-02-01

We determined the prevalence of work disability in early rheumatoid arthritis (ERA) and undifferentiated early inflammatory arthritis (EIA) patients at first enrollment into the Canadian Early Arthritis Cohort (CATCH) who met the 2010 ACR criteria versus those not meeting criteria, to determine the impact of meeting new criteria on work disability status. Data at first visit into the cohort were analyzed. Descriptive statistics and logistic regression analyses were performed to investigate the association of other variables in our database with work disability. 1,487 patients were enrolled in the CATCH study, a multi-site observational, prospective cohort of patients with EIA. 934 patients were excluded (505 based on missing criteria for ACR 2010 classification, as anti-CCP was absent, and 429 were not working for other reasons). Of the 553 patients included, 71 % were female with mean disease duration of 6.4 months. 524 (94.8 %) were employed while 29 (5.2 %) reported work disability at first visit. There were no differences between those meeting 2010 ACR criteria versus those who did not. Baseline characteristics associated with work disability were male gender, age, education, income, HAQ, and positive RF status. The mean HAQ score in work disabled patients was 1.4 versus 0.9 in those who were working (p 50 years; p = 0.3), lower education (p = 0.3) or RF positivity (p = 0.6). We found rates of work disability to be low at entry into this EIA cohort compared to previous studies. There may be potential for intervention in ERA to prevent the development of work disability.

Future enhanced clinical role of pharmacists in Emergency Departments in England: multi-site observational evaluation.

Science.gov (United States)

Hughes, Elizabeth; Terry, David; Huynh, Chi; Petridis, Konstantinos; Aiello, Matthew; Mazard, Louis; Ubhi, Hirminder; Terry, Alex; Wilson, Keith; Sinclair, Anthony

2017-08-01

Background There are concerns about maintaining appropriate clinical staffing levels in Emergency Departments. Pharmacists may be one possible solution. Objective To determine if Emergency Department attendees could be clinically managed by pharmacists with or without advanced clinical practice training. Setting Prospective 49 site cross-sectional observational study of patients attending Emergency Departments in England. Method Pharmacist data collectors identified patient attendance at their Emergency Department, recorded anonymized details of 400 cases and categorized each into one of four possible options: cases which could be managed by a community pharmacist; could be managed by a hospital pharmacist independent prescriber; could be managed by a hospital pharmacist independent prescriber with additional clinical training; or medical team only (unsuitable for pharmacists to manage). Impact indices sensitive to both workload and proportion of pharmacist manageable cases were calculated for each clinical group. Main outcome measure Proportion of cases which could be managed by a pharmacist. Results 18,613 cases were observed from 49 sites. 726 (3.9%) of cases were judged suitable for clinical management by community pharmacists, 719 (3.9%) by pharmacist prescribers, 5202 (27.9%) by pharmacist prescribers with further training, and 11,966 (64.3%) for medical team only. Impact Indices of the most frequent clinical groupings were general medicine (13.18) and orthopaedics (9.69). Conclusion The proportion of Emergency Department cases that could potentially be managed by a pharmacist was 36%. Greatest potential for pharmacist management was in general medicine and orthopaedics (usually minor trauma). Findings support the case for extending the clinical role of pharmacists.

PART I: Bioventing Pilot Test Work Plan for Fire Protection Training Area Site FY-03, Charleston AFB, South Carolina. PART II: Draft Interim Pilot Test Results Report for Fire Protection Training Area Site FT-03, Charleston AFB, South Carolina

National Research Council Canada - National Science Library

1993-01-01

This site-specific work plan presents the scope of a bioventing pilot test for in situ treatment of fuel contaminated soils at the Fire Protection Training Area designated as Site FT-O3, Charleston Air Force Base (AFB), South Carolina...

Working in the nuclear industry - Inquiry in the heart of a hazardous site

International Nuclear Information System (INIS)

Fournier, Pierre

2012-01-01

The author, who is today professor of sociology at the Aix-Marseille university (FR), has worked in the nuclear industry as a temp, as a trainee and as a subcontracting worker successively. In this book, he presents his vision from the inside of the daily work of nuclear workers. Inside teams, he has observed the behaviours, the relations between men, the ways to deal with an unsure knowledge, the conflicts which have occurred and the risks that the personnel has had to bear with. Beyond the ideological debate, and with no pro- or anti-position with respect to nuclear energy, the author presents a field report which allows to better comprehend the risk factors threatening the nuclear industry and the workers of this industry

Blended working: for whom it may (not work.

Directory of Open Access Journals (Sweden)

Nico W Van Yperen

Full Text Available Similarly to related developments such as blended learning and blended care, blended working is a pervasive and booming trend in modern societies. Blended working combines on-site and off-site working in an optimal way to improve workers' and organizations' outcomes. In this paper, we examine the degree to which workers feel that the two defining features of blended working (i.e., time-independent working and location-independent working enhance their own functioning in their jobs. Blended working, enabled through the continuing advance and improvement of high-tech ICT software, devices, and infrastructure, may be considered beneficial for workers' perceived effectiveness because it increases their job autonomy. However, because blended working may have downsides as well, it is important to know for whom blended working may (not work. As hypothesized, in a sample of 348 workers (51.7% women, representing a wide range of occupations and organizations, we found that the perceived personal effectiveness of blended working was contingent upon workers' psychological need strength. Specifically, the perceived effectiveness of both time-independent working and location-independent working was positively related to individuals' need for autonomy at work, and negatively related to their need for relatedness and need for structure at work.

Learning through Social Networking Sites--The Critical Role of the Teacher

Science.gov (United States)

Callaghan, Noelene; Bower, Matt

2012-01-01

This comparative case study examined factors affecting behaviour and learning in social networking sites (SNS). The behaviour and learning of two classes completing identical SNS based modules of work was observed and compared. All student contributions to the SNS were analysed, with the cognitive process dimension of the Revised Bloom's Taxonomy…

Evaluation of the site effect with Heuristic Methods

Science.gov (United States)

Torres, N. N.; Ortiz-Aleman, C.

2017-12-01

The seismic site response in an area depends mainly on the local geological and topographical conditions. Estimation of variations in ground motion can lead to significant contributions on seismic hazard assessment, in order to reduce human and economic losses. Site response estimation can be posed as a parameterized inversion approach which allows separating source and path effects. The generalized inversion (Field and Jacob, 1995) represents one of the alternative methods to estimate the local seismic response, which involves solving a strongly non-linear multiparametric problem. In this work, local seismic response was estimated using global optimization methods (Genetic Algorithms and Simulated Annealing) which allowed us to increase the range of explored solutions in a nonlinear search, as compared to other conventional linear methods. By using the VEOX Network velocity records, collected from August 2007 to March 2009, source, path and site parameters corresponding to the amplitude spectra of the S wave of the velocity seismic records are estimated. We can establish that inverted parameters resulting from this simultaneous inversion approach, show excellent agreement, not only in terms of adjustment between observed and calculated spectra, but also when compared to previous work from several authors.

Control of dry season evapotranspiration over the Amazonian forest as inferred from observations at a southern Amazon forest site

NARCIS (Netherlands)

Negrón Juárez, R.I.; Hodnett, M.G.; Fu, R.; Goulden, M.L.; Randow, von C.

2007-01-01

The extent to which soil water storage can support an average dry season evapotranspiration (ET) is investigated using observations from the Rebio Jarú site for the period of 2000 to 2002. During the dry season, when total rainfall is less than 100 mm, the soil moisture storage available to root

The role of safety analyses in site selection. Some personal observations based on the experience from the Swiss site selection process

Energy Technology Data Exchange (ETDEWEB)

Zuidema, Piet [Nagra, Wettingen (Switzerland)

2015-07-01

In Switzerland, the site selection process according to the ''Sectoral Plan for Deep Geological Repositories'' (BFE 2008) is underway since 2008. This process takes place in three stages. In stage 1 geological siting regions (six for the L/ILW repository and three for the HLW repository) have been identified, in stage 2 sites for the surface facilities have been identified for all siting regions in close co-operation with the sting regions and a narrowing down of the number of siting regions based on geological criteria will take place. In stage 3 the sites for a general license application are selected and the general license applications will be submitted which eventually will lead to the siting decision for both repository types. In the Swiss site selection process, safety has the highest priority. Many factors affect safety and thus a whole range of safety-related issues are considered in the identification and screening of siting possibilities. Besides dose calculations a range of quantitative and qualitative issues are considered. Dose calculations are performed in all three stages of the site selection process. In stage 1 generic safety calculations were made to develop criteria to be used for the identification of potential siting regions. In stage 2, dose calculations are made for comparing the different siting regions according to a procedure prescribed in detail by the regulator. Combined with qualitative evaluations this will lead to a narrowing down of the number of siting regions to at least two siting regions for each repository type. In stage 3 full safety cases will be prepared as part of the documentation for the general license applications. Besides the dose calculations, many other issues related to safety are analyzed in a quantitative and qualitative manner. These consider the 13 criteria defined in the Sectoral Plan and the corresponding indicators. The features analyzed cover the following broad themes: efficiency of

The role of safety analyses in site selection. Some personal observations based on the experience from the Swiss site selection process

International Nuclear Information System (INIS)

Zuidema, Piet

2015-01-01

In Switzerland, the site selection process according to the ''Sectoral Plan for Deep Geological Repositories'' (BFE 2008) is underway since 2008. This process takes place in three stages. In stage 1 geological siting regions (six for the L/ILW repository and three for the HLW repository) have been identified, in stage 2 sites for the surface facilities have been identified for all siting regions in close co-operation with the sting regions and a narrowing down of the number of siting regions based on geological criteria will take place. In stage 3 the sites for a general license application are selected and the general license applications will be submitted which eventually will lead to the siting decision for both repository types. In the Swiss site selection process, safety has the highest priority. Many factors affect safety and thus a whole range of safety-related issues are considered in the identification and screening of siting possibilities. Besides dose calculations a range of quantitative and qualitative issues are considered. Dose calculations are performed in all three stages of the site selection process. In stage 1 generic safety calculations were made to develop criteria to be used for the identification of potential siting regions. In stage 2, dose calculations are made for comparing the different siting regions according to a procedure prescribed in detail by the regulator. Combined with qualitative evaluations this will lead to a narrowing down of the number of siting regions to at least two siting regions for each repository type. In stage 3 full safety cases will be prepared as part of the documentation for the general license applications. Besides the dose calculations, many other issues related to safety are analyzed in a quantitative and qualitative manner. These consider the 13 criteria defined in the Sectoral Plan and the corresponding indicators. The features analyzed cover the following broad themes: efficiency of

Non-observance of guidelines for surgical antimicrobial prophylaxis and surgical-site infections.

Science.gov (United States)

Lallemand, S; Thouverez, M; Bailly, P; Bertrand, X; Talon, D

2002-06-01

A prospective multicentre study was conducted to assess major aspects of surgical prophylaxis and to determine whether inappropriate antimicrobial prophylaxis was a factor associated (risk or protective factor) with surgical site infection (SSI). Surgical prophylaxis practices were assessed by analysing four variables: indication, antimicrobial agent, timing and duration. Univariate and multivariate analyses were carried out to identify predictors of SSI among patient-specific, operation-specific and antimicrobial prophylaxis-specific factors. The frequency of SSI was 2.7% (13 SSI in 474 observations). Total compliance of the prescription with guidelines was observed in 41.1% of cases (195 prescriptions). Of the 139 patients who received an inappropriate drug, 126 (90.6%) received a drug with a broader spectrum than the recommended drug. Prophylaxis was prolonged in 71 (87.7%) of the 81 patients who received prophylaxis for inappropriate lengths of time and 43 (61.4%) of the 70 patients who did not receive prophylaxis at the optimal moment were treated too late. Multivariate analysis clearly demonstrated that SSI was associated with multiple procedures (relative risk 8.5), short duration of prophylaxis (relative risk 12.7) and long-term therapy with antimicrobial agents during the previous year (relative risk 8.8). The ecological risk of the emergence of resistance associated with the frequent use of broad-spectrum antibiotics and prophylaxis for longer periods was not offset by individual benefit to the patients who received inappropriate prophylaxis.

Impact of gastroesophageal reflux disease on work absenteeism, presenteeism and productivity in daily life: a European observational study

Science.gov (United States)

Gisbert, Javier P; Cooper, Alun; Karagiannis, Dimitrios; Hatlebakk, Jan; Agréus, Lars; Jablonowski, Helmut; Nuevo, Javier

2009-01-01

Background The RANGE (Retrospective ANalysis of GastroEsophageal reflux disease [GERD]) study assessed differences among patients consulting a primary care physician due to GERD-related reasons in terms of: symptoms, diagnosis and management, response to treatment, and effects on productivity, costs and health-related quality of life. This subanalysis of RANGE determined the impact of GERD on productivity in work and daily life. Methods RANGE was conducted at 134 primary care sites across six European countries (Germany, Greece, Norway, Spain, Sweden and the UK). All subjects (aged ≥18 years) who consulted with their primary care physician over a 4-month identification period were screened retrospectively, and those consulting at least once for GERD-related reasons were identified (index visit). From this population, a random sample was selected to enter the study and attended a follow-up appointment, during which the impact of GERD on productivity while working (absenteeism and presenteeism) and in daily life was evaluated using the self-reported Work Productivity and Activity Impairment Questionnaire for patients with GERD (WPAI-GERD). Results Overall, 373,610 subjects consulted with their primary care physician over the 4-month identification period, 12,815 for GERD-related reasons (3.4%); 2678 randomly selected patients attended the follow-up appointment. Average absenteeism due to GERD was highest in Germany (3.2 hours/week) and lowest in the UK (0.4 hours/week), with an average of up to 6.7 additional hours/week lost due to presenteeism in Norway. The average monetary impact of GERD-related work absenteeism and presenteeism were substantial in all countries (from €55/week per employed patient in the UK to €273/patient in Sweden). Reductions in productivity in daily life of up to 26% were observed across the European countries. Conclusion GERD places a significant burden on primary care patients, in terms of work absenteeism and presenteeism and in daily

Impact of gastroesophageal reflux disease on work absenteeism, presenteeism and productivity in daily life: a European observational study

Directory of Open Access Journals (Sweden)

Hatlebakk Jan

2009-10-01

Full Text Available Abstract Background The RANGE (Retrospective ANalysis of GastroEsophageal reflux disease [GERD] study assessed differences among patients consulting a primary care physician due to GERD-related reasons in terms of: symptoms, diagnosis and management, response to treatment, and effects on productivity, costs and health-related quality of life. This subanalysis of RANGE determined the impact of GERD on productivity in work and daily life. Methods RANGE was conducted at 134 primary care sites across six European countries (Germany, Greece, Norway, Spain, Sweden and the UK. All subjects (aged ≥18 years who consulted with their primary care physician over a 4-month identification period were screened retrospectively, and those consulting at least once for GERD-related reasons were identified (index visit. From this population, a random sample was selected to enter the study and attended a follow-up appointment, during which the impact of GERD on productivity while working (absenteeism and presenteeism and in daily life was evaluated using the self-reported Work Productivity and Activity Impairment Questionnaire for patients with GERD (WPAI-GERD. Results Overall, 373,610 subjects consulted with their primary care physician over the 4-month identification period, 12,815 for GERD-related reasons (3.4%; 2678 randomly selected patients attended the follow-up appointment. Average absenteeism due to GERD was highest in Germany (3.2 hours/week and lowest in the UK (0.4 hours/week, with an average of up to 6.7 additional hours/week lost due to presenteeism in Norway. The average monetary impact of GERD-related work absenteeism and presenteeism were substantial in all countries (from €55/week per employed patient in the UK to €273/patient in Sweden. Reductions in productivity in daily life of up to 26% were observed across the European countries. Conclusion GERD places a significant burden on primary care patients, in terms of work absenteeism and

Distinct site- and state-selective dissociation of methyl-trifluoroacetate observed in core-electron excitation at the oxygen K-edge region

Science.gov (United States)

Yamanaka, T.; Tabayashi, K.; Maruyama, T.; Harada, C.; Yoshida, H.

2009-11-01

Distinct site- and state-selective dissociation following the O1s core-excitation has been found in the gaseous molecules of methyl trifluoroacetate (MTFA). The site- and state-selective dissociation was examined by measuring the branching ratios of dominant CH3+ and CHO+ fragments. The branching ratios from MTFA showed that site-selective dissociation takes place via the excitation from the different atomic sites to the same π*CO resonance state, (O1sCO-1π*CO) and (O1sOMe-1π*CO). A pronounced O1sOMe site-selectivity was identified by a significant increment of CHO+ formation at the (O1sOMe→π*CO) band. The site-selectivity was also justified by an equivalent core approximation using the density functional theory calculation. State-selective dissociation was identified among the (O1sOMe-1π*CO), (O1sOMe-1σ*O-Me) and (O1sOMe-1σ*C-OMe) transitions originated from the same OMe core. State-selective production of CH3+ could be found at the (O1sOMe→σ*O-Me) band, whereas state-selective formation of CHO+ was observed at the (O1sOMe→π*CO) and (O1sOMe→σ*C-OMe) bands.

Characteristics of particulate matter collected at an urban background site and a roadside site in Birmingham, United Kingdom

OpenAIRE

Taiwo, Adewale M.

2017-01-01

ABSTRACT This study was conducted to investigate the compositional characteristics of particulate matter (PM) collected both at an urban background site (Elms Road observational site, EROS) and a roadside site (Bristol Road observational site, BROS). PM samples were collected at the receptor sites between March 28 and April 11, 2012. Observed parameters included water-soluble ions (Cl-, NO- 3, SO4 2-, Na+, NH4 +, K+, Mg2+, Ca2+) and trace metals (V, Al, Cr, Mn, Fe, Zn, Cu, Sb, Ba, Pb). Result...

Return to work in people with acquired brain injury: association with observed ability to use everyday technology.

Science.gov (United States)

Larsson-Lund, Maria; Kottorp, Anders; Malinowsky, Camilla

2017-07-01

The aim of this study was to explore how the observed ability to use everyday technology (ET), intrapersonal capacities and environmental characteristics related to ET use contributes to the likelihood of return to work in people with ABI. The aim was also to explore whether these variables added to the likelihood of return to work to earlier defined significant variables in the group: age, perceived ADL ability and perceived ability in ET use. A cross-sectional study. The Management of Everyday Technology Assessment (META), the short version of the Everyday Technology Use Questionnaire (S-ETUQ) and a revised version of the ADL taxonomy were used to evaluate 74 people with ABI. Individual ability measures from all assessments were generated by Rasch analyses and used for additional statistical analysis. The univariate analyses showed that the observed ability to use ET, as well as intrapersonal capacities and environmental characteristics related to ET use were all significantly associated with returning to work. In the multivariate analyses, none of these associations remained. The explanatory precision of return to work in people with ABI increased minimally by adding the observed ability to use ET and the variables related to ET use when age, perceived ability in ET use and ADL had been taken in account.

RCRA facility investigation/corrective measures study work plan for the 100-HR-3 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-09-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Under the Hanford Federal Facility Agreement and Consent Order, signed by the Washington State Department of Ecology (Ecology), EPA, and the US Department of Energy (DOE), more than 1000 inactive waste disposal and unplanned release sites on the Hanford Site have been grouped into a number of source and groundwater operable units. These operable units contain contamination in the form of hazardous waste, radioactive/hazardous mixed waste, and other CERCLA hazardous substances. Also included in the Tri-Party Agreement are 55 Resource Conservation and Recovery Act (RCRA) treatment, storage, or disposal (TSD) facilities that will be closed or permitted to operate in accordance with RCRA regulations, under the authority of Chapter 173-303 Washington Administrative Code (WAC). Some of the TSD facilities are included in the operable units. This work plan and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the RCRA facility investigation/corrective measures study (RFI/CMS) for the 100-HR-3 operable unit. The 100-HR-3 operable unit underlies the D/DR and H Areas, the 600 Area between them, and the six source operable units these areas contain. The 100-HR-3 operable unit includes all contamination found in the aquifer soils and water within its boundary. Source operable units include facilities and unplanned release sites that are potential sources of contamination. Separate work plans have been initiated for the 100-DR-1 (DOE-RL 1992a) and 100-HR-1 (DOE-RL 1992b) source operable units

Surfing Silicon Nanofacets for Cold Cathode Electron Emission Sites.

Science.gov (United States)

Basu, Tanmoy; Kumar, Mohit; Saini, Mahesh; Ghatak, Jay; Satpati, Biswarup; Som, Tapobrata

2017-11-08

Point sources exhibit low threshold electron emission due to local field enhancement at the tip. In the case of silicon, however, the realization of tip emitters has been hampered by unwanted oxidation, limiting the number of emission sites and the overall current. In contrast to this, here, we report the fascinating low threshold (∼0.67 V μm -1 ) cold cathode electron emission from silicon nanofacets (Si-NFs). The ensembles of nanofacets fabricated at different time scales, under low energy ion impacts, yield tunable field emission with a Fowler-Nordheim tunneling field in the range of 0.67-4.75 V μm -1 . The local probe surface microscopy-based tunneling current mapping in conjunction with Kelvin probe force microscopy measurements revealed that the valleys and a part of the sidewalls of the nanofacets contribute more to the field emission process. The observed lowest turn-on field is attributed to the absence of native oxide on the sidewalls of the smallest facets as well as their lowest work function. In addition, first-principle density functional theory-based simulation revealed a crystal orientation-dependent work function of Si, which corroborates well with our experimental observations. The present study demonstrates a novel way to address the origin of the cold cathode electron emission sites from Si-NFs fabricated at room temperature. In principle, the present methodology can be extended to probe the cold cathode electron emission sites from any nanostructured material.

Radionuclide migration in ground water at a low-level waste disposal site: a comparison of predicted radionuclide transport modeling versus field observations

International Nuclear Information System (INIS)

Bergeron, M.P.; Robertson, D.E.; Champ, D.R.; Killey, R.W.D.; Moltyaner, G.L.

1987-01-01

At the Chalk River Nuclear Laboratories (CRNL), in Ontario, Canada, a number of LLW shallow-land burial facilities have existed for 25-30 years. These facilities are useful for testing the concept of site modelability. In 1984, CRNL and the Pacific Northwest Laboratory (PNL) established a cooperative research program to examine two disposal sites having plumes of slightly contaminated ground water for study. This report addresses the LLW Nitrate Disposal Pit site, which received liquid wastes containing approximately 1000-1500 curies of mixed fission products during 1953-54. The objective of this study is to test the regulatory requirement that a site be modeled and to use the Nitrate Disposal Pit site as a field site for testing the reliability of models in predicting radionuclide movement in ground water. The study plan was to approach this site as though it were to be licensed under the requirements of 10 CFR 61. Under the assumption that little was known about this site, a characterization plan was prepared describing the geologic, hydrologic, and geochemical information needed to assess site performance. After completion of the plan, site data generated by CRNL were selected to fill the plan data requirements. This paper describes the site hydrogeology, modeling of ground water flow, the comparison of observed and predicted radionuclide movement, and summarizes the conclusions and recommendations. 3 references, 10 figures

Malargue site, to-day and its future

International Nuclear Information System (INIS)

Meza, Juan C.; Giordano, Norberto L.

2005-01-01

In Argentina the National Atomic Energy Commission (CNEA) has the responsibility of restoring uranium mining facilities once the operations have finished. To carry out these clean up actions CNEA created the Project for Uranium Mining Environmental Restoration (PRAMU). Malargue Site, Mendoza province, has the first restoration priority among 8 sites in the country. The approved project for restoration consists of on site relocation of tailings to an engineering repository. To isolate the tailings from the environment, a multilayer system has been designed. Several works have been made, the secondary previous works were completed and nowadays works on the button portion of the multilayer barrier are being carries out. At the present, it is quite probable that the World Bank grants a credit to finish the works on Malargue Site and in the other sites in Argentina as well. (author)

Remedial investigation/feasibility study work plan for the 300-FF-1 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1990-03-01

Over 1,400 waste facilities have been identified on the Hanford Site. Most of the waste facilities are located within geographic areas on the Hanford Site that are referred to as the 100, 200, 300, 400, and 1100 areas. The purpose of this work plan is to document the project scoping process and to outline all remedial investigation/feasibility study (RI/FS) activities, to determine the nature and extent of the threat presented by releases of hazardous substances from the operable unit, and to evaluate proposed remedies for such releases. The goal of the 300-FF-1 remedial investigation (RI) is to provide sufficient information needed to conduct the feasibility study (FS), by determining the nature and extent of the threat to public health and the environment posed by releases of hazardous substances from 300-FF-1, and the performance of specific remedial technologies. 62 refs., 28 figs., 48 tabs

Assessing recreation impacts to cliffs in Shenandoah National Park: Integrating visitor observation with trail and recreation site measurements

Science.gov (United States)

Wood, K.T.; Lawson, S.R.; Marion, J.L.

2006-01-01

The rock outcrops and cliffs of Shenandoah National Park provide habitat for several rare and endangered plant and animal species, including the federally endangered Shenandoah Salamander (Plethodon shenandoah; Ludwig et al., 1993). The location of the well-known park tour road, Skyline Drive, along the ridgeline provides exceptional access to many outcrops and cliffs throughout the park for a large number of the park?s 1.2 million annual visitors. Consequently, visitor use of cliff areas has led to natural resource impacts, including marked decreases in size and vigor of known rare plant populations. Despite the clear ecological value and potential threats to the natural resources at cliff areas, managers possess little information on visitor use of cliff sites and presently have no formal planning document to guide management. Thus, a park wide study of cliff sites was initiated during the 2005 visitor use season. As part of this research effort, our study used an integrative approach to study recreational use and visitor-caused resource impacts at one of the more heavily visited cliff sites in the park: Little Stony Man Cliffs (LSMC). In particular, this study integrated data from resource impact measurements and visitor use observation to help assess the effects of recreational use on the natural resources of LSMC. Procedures derived from campsite and trail impact studies were used to measure and characterize the amount of visitor-caused resource impacts on LSMC (Marion & Leung, 2001; Marion, 1995). Visitor use observations were conducted on top of LSMC to document and characterize the type and amount of recreational use the cliffs receive and the behaviors of recreationists that may contribute to cliff-top resource impacts. Resource impact measurement data show trampling disturbance present at LSMC, characterized by vegetation loss, exposed soil, and root exposure. Documentation of informal trails, soil erosion, tree damage, and tree stumps provide further

Direct radiative feedback due to biogenic secondary organic aerosol estimated from boreal forest site observations

International Nuclear Information System (INIS)

Lihavainen, Heikki; Asmi, Eija; Aaltonen, Veijo; Makkonen, Ulla; Kerminen, Veli-Matti

2015-01-01

We used more than five years of continuous aerosol measurements to estimate the direct radiative feedback parameter associated with the formation of biogenic secondary organic aerosol (BSOA) at a remote continental site at the edge of the boreal forest zone in Northern Finland. Our upper-limit estimate for this feedback parameter during the summer period (ambient temperatures above 10 °C) was −97 ± 66 mW m −2 K −1 (mean ± STD) when using measurements of the aerosol optical depth (f AOD ) and −63 ± 40 mW m −2 K −1 when using measurements of the ‘dry’ aerosol scattering coefficient at the ground level (f σ ). Here STD represents the variability in f caused by the observed variability in the quantities used to derive the value of f. Compared with our measurement site, the magnitude of the direct radiative feedback associated with BSOA is expected to be larger in warmer continental regions with more abundant biogenic emissions, and even larger in regions where biogenic emissions are mixed with anthropogenic pollution. (letter)

Pharmacy Service Orientation: a measure of organizational culture in pharmacy practice sites.

Science.gov (United States)

Clark, Bartholomew E; Mount, Jeanine K

2006-03-01

The importance of organizational culture in shaping everyday organizational life is well accepted, but little work has focused on organizational culture in pharmacy. Examining new pharmacists' experiences at various practice sites may help us to understand how these shape their professional ethos and practice habits. (1) Present development and assessment of the Pharmacy Service Orientation (PSO) measure, a tool for assessing pharmacists' impressions of pharmacy practice sites. (2) Use data gathered from a sample of new pharmacists to explore potential predictors of PSO, including type of practice site, type of pharmacy work experience, and type of pharmacy degree. Mail survey of randomly selected class of 1999 pharmacy graduates within 3 months of graduation (response rate: 259 of 1,850; 14%), each of whom reported on up to 6 different pharmacy practice sites for a total of 1,192 pharmacy observations. Pharmacy Service Orientation is scored on a 1-10 semantic differential scale and reliability was assessed using Cronbach's alpha. Predictors of PSO were explored using t test and ordinary least squares regression procedures. Reliability of the PSO across all observations was 0.86. When divided according to recency of experience and type of experience, reliabilities ranged from 0.78 to 0.87. Analysis of potential predictors of PSO showed that non-corporate-community sites had significantly greater pharmaceutical care-oriented cultures (mean PSOs of 7.42 and 5.13, respectively; PService Orientation is a reliable measure. Statistically significant differences in PSO comparisons by degree and by experience type are explained by significant differences between the PSOs of corporate-community and non-corporate-community sites.

The management of abandoned sites at the basin collieries of center and southern France and the procedure of stoppage of mining works

International Nuclear Information System (INIS)

Barriere, J.P.

2003-01-01

The basin collieries of center and southern France (HBCM) have launched since 1993 the procedures of stoppage of mining works as foreseen by the mining rights and which will lead to the renunciation of their 148 concessions once the remediation of the sites has been completed. In order to cope with the enormous work of file and work follow up, a rigorous procedure and organization has been implemented in order to obtain all necessary prefecture by-laws by the end of 2005. (J.S.)

A future for nuclear sites beyond their service life. Nuclear site value development; Un avenir pour les sites nucleaires en fin de cycle. Valorisation des sites nucleaires

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

As the nuclear industry moves into a new development phase, many facilities built in the fifties and sixties are reaching the end of their service life. Dismantling them and rehabilitating the sites on which they stand is a major industrial challenge which will give rise to a number of new projects. AREVA has more than 20 years' experience in these highly technical fields. As more and more sites reach the end of their service life, AREVA considers nuclear site value development as a fully-fledged industrial activity. The group's competencies in this field have been grouped together to form a dedicated entity: the Nuclear Site Value Development Business Unit, created in 2008. Several billion euros are invested in site value development projects which are far-reaching and complex, and often last for several decades. Long before work actually begins, lengthy studies and preparations are required to schedule operations, select the techniques to be used and optimize costs and deadlines. The Nuclear Site Value Development BU is currently working on four major projects involving its own facilities and those of the CEA: - La Hague: dismantling of the first generation of used fuel recycling facilities. Between 1966 and 1998, almost 5,000 tons of used fuel from graphite-moderated gas-cooled reactors, 4,500 tons of light water reactor fuel, as well as fuel from fast reactors and research reactors, were treated at UP2 400, the very first industrial recycling plant on the La Hague site. - Marcoule: first-time dismantling of a recycling plant. 1,000 rooms to be cleaned up, 30,000 tons of waste to be treated, 30 years of work. - Cadarache: first-time dismantling of a Mox fuel fabrication plant. The Cadarache plant was commissioned in 1962 to fabricate fuel for fast reactors; this was followed by MOX fuel for light water reactors, an activity which continued until the plant was shut down in 2003. - Annecy and Veurey: giving a new lease of life to former industrial sites

National Ignition Facility Project Site Safety Program

International Nuclear Information System (INIS)

Dun, C

2003-01-01

This Safety Program for the National Ignition Facility (NIF) presents safety protocols and requirements that management and workers shall follow to assure a safe and healthful work environment during activities performed on the NIF Project site. The NIF Project Site Safety Program (NPSSP) requires that activities at the NIF Project site be performed in accordance with the ''LLNL ES and H Manual'' and the augmented set of controls and processes described in this NIF Project Site Safety Program. Specifically, this document: (1) Defines the fundamental NIF site safety philosophy. (2) Defines the areas covered by this safety program (see Appendix B). (3) Identifies management roles and responsibilities. (4) Defines core safety management processes. (5) Identifies NIF site-specific safety requirements. This NPSSP sets forth the responsibilities, requirements, rules, policies, and regulations for workers involved in work activities performed on the NIF Project site. Workers are required to implement measures to create a universal awareness that promotes safe practice at the work site and will achieve NIF management objectives in preventing accidents and illnesses. ES and H requirements are consistent with the ''LLNL ES and H Manual''. This NPSSP and implementing procedures (e.g., Management Walkabout, special work procedures, etc.,) are a comprehensive safety program that applies to NIF workers on the NIF Project site. The NIF Project site includes the B581/B681 site and support areas shown in Appendix B

The SARA REU Site Program

Science.gov (United States)

Wood, M. A.; Oswalt, T. D.; SARA Collaboration

2000-12-01

We present an overview of the Research Experiences for Undergraduates (REU) Site Program hosted by the Southeastern Association for Research in Astronomy (SARA) for the past 6 years. SARA is a consortium of the six universities: Florida Institute of Technology, East Tennessee State University, Florida International University, The University of Georgia, Valdosta State University, and Clemson University. We host 10-11 student interns per year out of an application pool of ~150-200. Recruiting flyers are sent to the ~3400 undergraduate institutions in the United States, and we use a web-based application form and review process. We are a distributed REU Site, but come together for group meetings at the beginning and end of the summer program and stay in contact in between using email list manager software. Interns complete a research project working one-on-one with a faculty mentor, and each intern travels to observe at the SARA Observatory at Kitt Peak National Observatory. Interns give both oral and display presentations of their results at the final group meeting. In addition, all interns write a paper for publication in the IAPPP Communications, an international amateur-professional journal, and several present at professional meetings and in refereed publications. We include in the group meetings a ``how-to'' session on giving talks and posters, an Ethics Session, and a session on Women in Astronomy. This work was supported by the NSF Research Experiences for Undergraduates (REU) Site Program through grant AST 96169939 to The Florida Institute of Technology.

Results of the 1987 Archeological Investigations at the Travis 2 Site, 39WW15, Walworth County, South Dakota

Science.gov (United States)

1988-09-01

only approximately 25 percent of the ground surface was visible during field work. The beach areas of the site are essentially barren of vegetation so...7.6. Pollen types observed in samples from the Travis 2 site, 39WW15. Common Name ARBOREAL POLLEN: Betulaceae Birch family Pinus Pine Populus...David W. (editor) 1981 Archaeoloical Investigations at the Rainbow Site Plymouth Countyifowa. Luther Coll ige-rchaeologica’Research Center, Decorah

Creation of integrated information model of 'Ukryttya' object premises and industrial site conditions to support works

International Nuclear Information System (INIS)

Postil, S.D.; Ermolenko, A.I.; Ivanov, V.V.; Kotlyarov, V.T.

2004-01-01

Data integration is made using standard AutoCAD utility and special software developed in Visual Basic for Application language. Mutual transfer is realized between the applications prepared in Access and AutoCAD with displaying the submitted information. The work demonstrates a possibility to apply integrated information model for investigating radiation field's change and analysis regularities in premises and on industrial site area, development and visualization, with the use of computer animation means, of movement routes, displaying of emergency situations being forecast with the help of computer graphics means, integration of raster display of structures and vector computer model of objects

EVALUATION OF THE MAIN CEOS PSEUDO CALIBRATION SITES USING MODIS BRDF/ALBEDO PRODUCTS

Directory of Open Access Journals (Sweden)

S. Kharbouche

2016-06-01

Full Text Available This work describes our findings about an evaluation of the stability and the consistency of twenty primary PICSs (Pseudo-Invariant Calibration Sites. We present an analysis of 13 years of 8-daily MODIS products of BRDF parameters and white-sky-albedos (WSA over the shortwave band. This time series of WSA and BRDFs shows the variation of the “stability” varies significantly from site to site. Using a 10x10 km window size over all the sites, the change in of WSA stability is around 4% but the isotropicity, which is an important element in inter-satellite calibration, can vary from 75% to 98%. Moreover, some PICS, especially, Libya-4 which is one of the PICS which is most employed, has significant and relatively fast changes in wintertime. PICS observations of BRDF/albedo shows that the Libya-4 PICS has the best performance but it is not too far from some sites such as Libya-1 and Mali. This study also reveals that Niger-3 PICS has the longest continuous period of high stability per year, and Sudan has the most isotropic surface. These observations have important implications for the use of these sites.

Political science. Reverse-engineering censorship in China: randomized experimentation and participant observation.

Science.gov (United States)

King, Gary; Pan, Jennifer; Roberts, Margaret E

2014-08-22

Existing research on the extensive Chinese censorship organization uses observational methods with well-known limitations. We conducted the first large-scale experimental study of censorship by creating accounts on numerous social media sites, randomly submitting different texts, and observing from a worldwide network of computers which texts were censored and which were not. We also supplemented interviews with confidential sources by creating our own social media site, contracting with Chinese firms to install the same censoring technologies as existing sites, and--with their software, documentation, and even customer support--reverse-engineering how it all works. Our results offer rigorous support for the recent hypothesis that criticisms of the state, its leaders, and their policies are published, whereas posts about real-world events with collective action potential are censored. Copyright © 2014, American Association for the Advancement of Science.

NOAA History - About This Site

Science.gov (United States)

NOAA History Banner gold bar divider home - takes you to index page about the site contacts noaa - takes you to the noaa home page search this site white divider about this site The NOAA History site is the result of the work of many individuals throughout 3d history page NOAA who have been inspired by

Working together with regulators on nuclear sites

International Nuclear Information System (INIS)

Holloway, N.J.

2004-01-01

A scheme for earlier and clearer communications with the Health and Safety Executive (HSE) and the Environment Agency (EA) on jointly regulated issues has been developed across the nuclear industry over the past two years. The matched pair of industry and regulators' 'Working Together' documents was published in January 2003. In the United Kingdom Atomic Energy Authority (UKAEA), the scheme is being put into practice through the issue of Initial Regulatory Notifications (IRN) of various projects and issues, to capture key regulatory topics and prompt regulators' initial responses. The IRN may be based on a safety and environment overview report or may be a precursor to it. Positive responses, in line with the Working Together documents, were received from HSE and the EA, following receipt of the first three UKAEA IRNs. (author)

Remedial investigation/feasibility study work plan for the 100-KR-1 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-07-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Figure 1-1 shows the location of these areas. Under the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement, Ecology et al. 1990a), signed by the Washington State Department of Ecology (Ecology), EPA, and the US Department of Energy (DOE), more than 1,000 inactive waste disposal and unplanned release sites on the Hanford Site have been grouped into a number of source and groundwater operable units. These operable units contain contamination in the form of hazardous waste, radioactive/hazardous mixed waste, and other CERCLA hazardous substances. Also included in the Tri-Party Agreement are 55 Resource Conservation and Recovery Act (RCRA) treatment, storage, or disposal (TSD) facilities that will be closed or permitted to operate in accordance with RCRA regulations, under the authority of Chapter 173-303 Washington Administrative Code (WAC). Some of the TSD facilities are included in the operable units. This work plan and the attached supporting project plans establish the objectives, procedures, tasks, and schedule for conducting the CERCLA remedial investigation/feasibility study (RI/FS) for the 100-KR-1 operable unit. The 100-KR-1 source operable unit is one of three source operable units in the 100-K Area. Source operable units include facilities and unplanned release sites that are potential sources of hazardous substance contamination

The Hanford Site focus, 1994

International Nuclear Information System (INIS)

Peterson, J.M.

1994-03-01

This report describes what the Hanford Site will look like in the next two years. We offer thumbnail sketches of Hanford Site programs and the needs we are meeting through our efforts. We describe our goals, some recent accomplishments, the work we will do in fiscal year (FY) 1994, the major activities the FY 1995 budget request covers, and the economic picture in the next few years. The Hanford Site budget shows the type of work being planned. US Department of Energy (DOE) sites like the Hanford Site use documents called Activity Data Sheets to meet this need. These are building blocks that are included in the budget. Each Activity Data Sheet is a concise (usually 4 or 5 pages) summary of a piece of work funded by the DOE's Environmental Restoration and Waste Management budget. Each sheet describes a waste management or environmental restoration need over a 5-year period; related regulatory requirements and agreements; and the cost, milestones, and steps proposed to meet the need. The Hanford Site is complex and has a huge budget, and its Activity Data Sheets run to literally thousands of pages. This report summarizes the Activity Data Sheets in a less detailed and much more reader-friendly fashion

Implementing ‘Site BIM’

DEFF Research Database (Denmark)

Davies, Richard; Harty, Chris

2013-01-01

Numerous Building Information Modelling (BIM) tools are well established and potentially beneficial in certain uses. However, issues of adoption and implementation persist, particularly for on-site use of BIM tools in the construction phase. We describe an empirical case-study of the implementation...... of an innovative ‘Site BIM’ system on a major hospital construction project. The main contractor on the project developed BIM-enabled tools to allow site workers using mobile tablet personal computers to access design information and to capture work quality and progress data on-site. Accounts show that ‘Site BIM...

Trampoline Effect: Observations and Modeling

Science.gov (United States)

Guyer, R.; Larmat, C. S.; Ulrich, T. J.

2009-12-01

The Iwate-Miyagi earthquake at site IWTH25 (14 June 2008) had large, asymmetric at surface vertical accelerations prompting the sobriquet trampoline effect (Aoi et. al. 2008). In addition the surface acceleration record showed long-short waiting time correlations and vertical-horizontal acceleration correlations. A lumped element model, deduced from the equations of continuum elasticity, is employed to describe the behavior at this site in terms of a surface layer and substrate. Important ingredients in the model are the nonlinear vertical coupling between the surface layer and the substrate and the nonlinear horizontal frictional coupling between the surface layer and the substrate. The model produces results in qualitative accord with observations: acceleration asymmetry, Fourier spectrum, waiting time correlations and vertical acceleration-horizontal acceleration correlations. [We gratefully acknowledge the support of the U. S. Department of Energy through the LANL/LDRD Program for this work].

Improving construction site safety through leader-based verbal safety communication.

Science.gov (United States)

Kines, Pete; Andersen, Lars P S; Spangenberg, Soren; Mikkelsen, Kim L; Dyreborg, Johnny; Zohar, Dov

2010-10-01

The construction industry is one of the most injury-prone industries, in which production is usually prioritized over safety in daily on-site communication. Workers have an informal and oral culture of risk, in which safety is rarely openly expressed. This paper tests the effect of increasing leader-based on-site verbal safety communication on the level of safety and safety climate at construction sites. A pre-post intervention-control design with five construction work gangs is carried out. Foremen in two intervention groups are coached and given bi-weekly feedback about their daily verbal safety communications with their workers. Foremen-worker verbal safety exchanges (experience sampling method, n=1,693 interviews), construction site safety level (correct vs. incorrect, n=22,077 single observations), and safety climate (seven dimensions, n=105 questionnaires) are measured over a period of up to 42 weeks. Baseline measurements in the two intervention and three control groups reveal that foremen speak with their workers several times a day. Workers perceive safety as part of their verbal communication with their foremen in only 6-16% of exchanges, and the levels of safety at the sites range from 70-87% (correct observations). Measurements from baseline to follow-up in the two intervention groups reveal that safety communication between foremen and workers increases significantly in one of the groups (factor 7.1 increase), and a significant yet smaller increase is found when the two intervention groups are combined (factor 4.6). Significant increases in the level of safety are seen in both intervention groups (7% and 12% increases, respectively), particularly in regards to 'access ways' and 'railings and coverings' (39% and 84% increases, respectively). Increases in safety climate are seen in only one of the intervention groups with respect to their 'attention to safety.' No significant trend changes are seen in the three control groups on any of the three measures

Status report: Fernald site remediation

International Nuclear Information System (INIS)

Craig, J.R. Jr.; Saric, J.A.; Schneider, T.; Yates, M.K.

1995-01-01

The Fernald site is rapidly transitioning from a Remedial Investigation/ Feasibility Study (RI/FS) site to one where design and construction of the remedies dominates. Fernald is one of the first sites in the Department of Energy (DOE) complex to accomplish this task and real physical progress is being made in moving the five operable units through the CERCLA process. Two of the required Records of Decision (ROD) are in hand and all five operable units will have received their RODs (IROD for OU3) by the end of 1995. Pre-design investigations, design work or construction are now in progress on the operable units. The lessons learned from the work done to date include implementing innovations in the RI and FS process as well as effective use of Removal Actions to begin the actual site remediation. Also, forging close working relationships with the Federal and State Regulators, citizens action groups and the Fernald Citizens Task Force has helped move the program forward. The Fernald successes have been achieved by close coordination and cooperation among all groups working on the projects and by application of innovative technologies within the decision making process

Radiological surveillance of Remedial Action activities at the processing site, Ambrosia Lake, New Mexico, April 12--16, 1993. Final report

International Nuclear Information System (INIS)

1993-04-01

The Uranium Mill Tailings Remedial Action (UMTRA) Project's Technical Assistance Contractor (TAC) performed a radiological surveillance of the Remedial Action Contractor (RAC), MK-Ferguson and CWM Federal Environmental Services, Inc., at the processing site in Ambrosia Lake, New Mexico. The requirements and attributes examined during the audit were developed from reviewing working-level procedures developed by the RAC. Objective evidence, comments, and observations were verified based on investigating procedures, documentation, records located at the site, personal interviews, and tours of the site. No findings were identified during this audit. Ten site-specific observations, three good practice observations, and five programmatic observations are presented in this report. The overall conclusion from the surveillance is that the radiological aspects of the Ambrosia Lake, New Mexico, remedial action program are performed adequately. The results of the good practice observations indicate that the site health physics (HP) staff is taking the initiative to address and resolve potential issues, and implement suggestions useful to the UMTRA Project. However, potential exists for improving designated storage areas for general items, and the RAC Project Office should consider resolving site-specific and procedural inconsistencies

Inter-rater reliability of direct observations of the physical and psychosocial working conditions in eldercare: An evaluation in the DOSES project

NARCIS (Netherlands)

Karstad, K. (Kristina); Rugulies, R. (Reiner); Skotte, J. (Jørgen); Munch, P.K. (Pernille Kold); Greiner, B.A. (Birgit A.); Burdorf, A. (Alex); Søgaard, K. (Karen); A. Holtermann (Andreas)

2018-01-01

textabstractThe aim of the study was to develop and evaluate the reliability of the “Danish observational study of eldercare work and musculoskeletal disorders” (DOSES) observation instrument to assess physical and psychosocial risk factors for musculoskeletal disorders (MSD) in eldercare work.

Radiological audit of remedial action activities at the processing site, transfer site, and Cheney disposal site Grand Junction, Colorado: Audit date, August 9--11, 1993

International Nuclear Information System (INIS)

1993-08-01

The Uranium Mill Tailing Remedial Action (UMTRA) Project's Technical Assistance Contractor (TAC) performed a radiological audit of the Remedial Action Contractor (RAC), MK-Ferguson and CWM Federal Environmental Services, Inc., at the processing site, transfer site, and Cheney disposal site in Grand Junction, Colorado. Jim Hylko and Bill James of the TAC conducted this audit August 9 through 11, 1993. Bob Cornish and Frank Bosiljevec represented the US Department of Energy (DOE). This report presents one programmatic finding, eleven site-specific observations, one good practice, and four programmatic observations

Analysis of the GPS Observations of the Site Survey at Sheshan 25-m Radio Telescope in August 2008

Science.gov (United States)

Liu, L.; Cheng, Z. Y.; Li, J. L.

2010-01-01

The processing of the GPS observations of the site survey at Sheshan 25-m radio telescope in August 2008 is reported. Because each session in this survey is only about six hours, not allowing the subdaily high frequency variations in the station coordinates to be reasonably smoothed, and because there are serious cycle slips in the observations and a large volume of data would be rejected during the software automatic adjustment of slips, the ordinary solution settings of GAMIT needed to be adjusted by loosening the constraints in the a priori coordinates to 10 m, adopting the "quick" mode in the solution iteration, and combining Cview manual operation with GAMIT automatic fixing of cycle slips. The resulting coordinates of the local control polygon in ITRF2005 are then compared with conventional geodetic results. Due to large rotations and translations in the two sets of coordinates (geocentric versus quasi-topocentric), the seven transformation parameters cannot be solved for directly. With various trial solutions it is shown that with a partial pre-removal of the large parameters, high precision transformation parameters can be obtained with post-fit residuals at the millimeter level. This analysis is necessary to prepare the follow-on site and transformation survey of the VLBI and SLR telescopes at Sheshan

Site description of Forsmark at completion of the site investigation phase. SDM-Site Forsmark

Energy Technology Data Exchange (ETDEWEB)

2008-12-15

north-western part of the candidate area lacks hydraulically conductive, gently dipping fracture zones at potential repository depth and was selected as the target area for the complete site investigation work, following the initial investigations at the site. Prior to the presentation of the SDM-Site report, three versions of a site descriptive model have been completed for the Forsmark area and presented for peer review. The last version, referred to as version 1.2, was a preliminary site description that concluded the initial site investigation work and was presented in 2005. This preliminary site description formed the basis for a preliminary safety evaluation (PSE) of the Forsmark area, a preliminary repository layout (step D1), and the first evaluation of the long-term safety of this layout for KBS-3 repositories in the context of the SR-Can project. The final site descriptive model, SDM-Site, builds on a coordinated geological model in 3D, into which other discipline-specific models have been integrated without any major conflicting interpretations. In particular, the thermal properties of the bedrock at the site have been coupled to identified rock domains in the geological model and an integrated model that links the current stress regime, the hydrogeology and the chemistry of the groundwater to fracture domains and fracture zones in the geological model has evolved. These mutually consistent results demonstrate that a fundamental understanding of the current state of conditions and the on-going processes in the Forsmark area, from the surface down to potential repository depth, has been achieved. In addition, the properties of the area can be explained in the context of an understanding of the past evolution, throughout a long period of geological history. This integrated understanding of the area is presented in chapter 11 of this report and this chapter serves as an executive summary. A systematic assessment of the confidence in the model, including

Site description of Forsmark at completion of the site investigation phase. SDM-Site Forsmark

International Nuclear Information System (INIS)

2008-12-01

north-western part of the candidate area lacks hydraulically conductive, gently dipping fracture zones at potential repository depth and was selected as the target area for the complete site investigation work, following the initial investigations at the site. Prior to the presentation of the SDM-Site report, three versions of a site descriptive model have been completed for the Forsmark area and presented for peer review. The last version, referred to as version 1.2, was a preliminary site description that concluded the initial site investigation work and was presented in 2005. This preliminary site description formed the basis for a preliminary safety evaluation (PSE) of the Forsmark area, a preliminary repository layout (step D1), and the first evaluation of the long-term safety of this layout for KBS-3 repositories in the context of the SR-Can project. The final site descriptive model, SDM-Site, builds on a coordinated geological model in 3D, into which other discipline-specific models have been integrated without any major conflicting interpretations. In particular, the thermal properties of the bedrock at the site have been coupled to identified rock domains in the geological model and an integrated model that links the current stress regime, the hydrogeology and the chemistry of the groundwater to fracture domains and fracture zones in the geological model has evolved. These mutually consistent results demonstrate that a fundamental understanding of the current state of conditions and the on-going processes in the Forsmark area, from the surface down to potential repository depth, has been achieved. In addition, the properties of the area can be explained in the context of an understanding of the past evolution, throughout a long period of geological history. This integrated understanding of the area is presented in chapter 11 of this report and this chapter serves as an executive summary. A systematic assessment of the confidence in the model, including

Risk-based analyses in support of California hazardous site remediation

International Nuclear Information System (INIS)

Ringland, J.T.

1995-08-01

The California Environmental Enterprise (CEE) is a joint program of the Department of Energy (DOE), Lawrence Livermore National Laboratory, Lawrence Berkeley Laboratory, and Sandia National Laboratories. Its goal is to make DOE laboratory expertise accessible to hazardous site cleanups in the state This support might involve working directly with parties responsible for individual cleanups or it might involve working with the California Environmental Protection Agency to develop tools that would be applicable across a broad range of sites. As part of its initial year's activities, the CEE supported a review to examine where laboratory risk and risk-based systems analysis capabilities might be most effectively applied. To this end, this study draws the following observations. The labs have a clear role in analyses supporting the demonstration and transfer of laboratory characterization or remediation technologies. The labs may have opportunities in developing broadly applicable analysis tools and computer codes for problems such as site characterization or efficient management of resources. Analysis at individual sites, separate from supporting lab technologies or prototyping general tools, may be appropriate only in limited circumstances. In any of these roles, the labs' capabilities extend beyond health risk assessment to the broader areas of risk management and risk-based systems analysis

Prevalence and Characteristics of Work Anxiety in Medical Rehabilitation Patients: A Cross-Sectional Observation Study.

Science.gov (United States)

Muschalla, Beate; Jöbges, Michael

2018-01-01

To investigate frequency, type, and characteristics of work anxieties in patients with somatic illness. Cross-sectional observation study. Neurology, orthopedic, and cardiology rehabilitation clinics. Patients (N=1610; age, 18-65y) with work anxieties. Not applicable. Patients who scored high on at least 2 of 9 items in the work-anxiety screening questionnaire and who reported impairment were investigated with a differential diagnostic interview on work anxieties and with the Mini-International Neuropsychiatric Interview on non-work-related common mental disorders. Patients also filled out a self-rating questionnaire on their subjective symptom load and sociodemographic data. Approximately 20% to 27% of the investigated inpatients in somatic rehabilitation (altogether n=393) received a work-anxiety diagnosis. Patients with orthopedic illness report highest work anxiety and have previous longest sick leave (20.6wk in the past 12mo). Patients with orthopedic illness suffer from work-related adjustment disorder with anxiety, social anxieties, and workplace phobias, whereas patients with cardiac illness are more often affected by hypochondriac anxieties. Anxieties of insufficiency and worrying occur equally in all indications. About a quarter of patients in somatic rehabilitation are in need of additional diagnostic attention owing to work anxieties. Differential diagnostic of work anxiety is needed for initiating adequate therapeutic action. Somatic rehabilitation physicians should be aware of work anxieties in their patients, especially in patients with orthopedic illness with previous long-term sick leave. Copyright © 2017 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Work plan for ground water elevation data recorder/monitor well installation at the New Rifle Site, Rifle, Colorado

International Nuclear Information System (INIS)

1994-01-01

The purpose of this document is to describe the work that will be performed and the procedures that will be followed during installation of ground water monitor wells and ground water elevation data recorders (data loggers) at the New Rifle Uranium Mill Tailings Remedial Action (UMTRA) Project site, Rifle, Colorado. The monitor wells and data loggers will be used to gather required time-dependent data to investigate the interaction between the shallow aquifer and the Colorado River

Scope of work-supplemental standards-related fieldwork - Salt Lake City UMTRA Project Site, Salt Lake City, Utah

International Nuclear Information System (INIS)

1996-01-01

This scope of work governs the field effort to conduct transient in situ (hereafter referred to by the trademark name HydroPunch reg-sign) investigative subsurface logging and ground water sampling, and perform well point installation services at the U.S. Department of Energy's (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site near Salt Lake City, Utah. The HydroPunch reg-sign and well point services subcontractor (the Subcontractor) shall provide services as stated herein to be used to investigate the subsurface, collect and analyze ground water samples, and install shallow well points

Innovations in Site Characterization Case Study: Site Cleanup of the Wenatchee Tree Fruit Test Plot Site Using a Dynamic Work Plan

Science.gov (United States)

The Wenatchee Tree Fruit Research and Extension Center site contained soils contaminated with organochlorine pesticides, organophosphorus pesticides, and other pesticides due to agriculture-related research activities conducted from 1966 until...

CMS : An exceptional load for an exceptional work site

CERN Multimedia

2001-01-01

Components of the CMS vacuum tank have been delivered to the detector assembly site at Cessy. The complete inner shell was delivered to CERN by special convoy while the outer shell is being assembled in situ. The convoy transporting the inner shell of the CMS vacuum tank took a week to cover the distance between Lons-le-Saunier and Point 5 at Cessy. Left: the convoy making its way down from the Col de la Faucille. With lights flashing, flanked by police outriders and with roads temporarily closed, the exceptional load that passed through the Pays de Gex on Monday 20 May was accorded the same VIP treatment as a leading state dignitary. But this time it was not the identity of the passenger but the exceptional size of the object being transported that made such arrangements necessary. A convoy of two lorries was needed to transport the load, an enormous 13-metre long, 6 metre diameter cylinder weighing 120 tonnes. It took a week to cover the 120 kilometres between Lons-le-Saunier and the assembly site for...

Slower CCN growth kinetics of anthropogenic aerosol compared to biogenic aerosol observed at a rural site

Science.gov (United States)

Shantz, N. C.; Chang, R. Y.-W.; Slowik, J. G.; Vlasenko, A.; Abbatt, J. P. D.; Leaitch, W. R.

2010-01-01

Growth rates of water droplets were measured with a static diffusion cloud condensation chamber in May-June 2007 at a rural field site in Southern Ontario, Canada, 70 km north of Toronto. The observations include periods when the winds were from the south and the site was impacted by anthropogenic air from the U.S. and Southern Ontario as well as during a 5-day period of northerly wind flow when the aerosol was dominated by biogenic sources. The growth of droplets on anthropogenic size-selected particles centred at 0.1 μm diameter and composed of approximately 40% organic and 60% ammonium sulphate (AS) by mass, was delayed by on the order of 1 s compared to a pure AS aerosol. Simulations of the growth rate on monodisperse particles indicate that a lowering of the water mass accommodation coefficient from αc=1 to an average of αc=0.04 is needed (assuming an insoluble organic with hygroscopicity parameter, κorg, of zero). Simulations of the initial growth rate on polydisperse anthropogenic particles agree best with observations for αc=0.07. In contrast, the growth rate of droplets on size-selected aerosol of biogenic character, consisting of >80% organic, was similar to that of pure AS. Simulations of the predominantly biogenic polydisperse aerosol show agreement between the observations and simulations when κorg=0.2 (with upper and lower limits of 0.5 and 0.07, respectively) and αc=1. Inhibition of water uptake by the anthropogenic organic applied to an adiabatic cloud parcel model in the form of a constant low αc increases the number of droplets in a cloud compared to pure AS. If the αc is assumed to increase with increasing liquid water on the droplets, then the number of droplets decreases which could diminish the indirect climate forcing effect. The slightly lower κorg in the biogenic case decreases the number of droplets in a cloud compared to pure AS.

Early Site Permit Demonstration Program: Siting Guide, Site selection and evaluation criteria for an early site permit application

International Nuclear Information System (INIS)

1993-01-01

In August 1991, the Joint Contractors came to agreement with Sandia National Laboratories (SNL) and the Department of Energy (DOE) on a workscope for the cost-shared Early Site Permit Demonstration Program. One task within the scope was the development of a guide for site selection criteria and procedures. A generic Siting Guide his been prepared that is a roadmap and tool for applicants to use developing detailed siting plans for their specific region of the country. The guide presents three fundamental principles that, if used, ensure a high degree of success for an ESP applicant. First, the site selection process should take into consideration environmentally diverse site locations within a given region of interest. Second, the process should contain appropriate opportunities for input from the public. Third, the process should be applied so that it is clearly reasonable to an impartial observer, based on appropriately selected criteria, including criteria which demonstrate that the site can host an advanced light water reactor (ALWR). The Siting Guide provides for a systematic, comprehensive site selection process in which three basic types of criteria (exclusionary, avoidance, and suitability) are presented via a four-step procedure. It provides a check list of the criteria for each one of these steps. Criteria are applied qualitatively, as well as presented numerically, within the guide. The applicant should use the generic guide as an exhaustive checklist, customizing the guide to his individual situation

Geological discrete fracture network model for the Laxemar site. Site Descriptive Modelling. SDM-Site Laxemar

Energy Technology Data Exchange (ETDEWEB)

La Pointe, Paul; Fox, Aaron (Golder Associates Inc (United States)); Hermanson, Jan; Oehman, Johan (Golder Associates AB, Stockholm (Sweden))

2008-12-15

The Swedish Nuclear Fuel and Waste Management Company (SKB) is performing site characterization at two different locations, Forsmark and Laxemar, in order to locate a site for a final geologic repository for spent nuclear fuel. The program is built upon the development of Site Descriptive Models (SDMs) at specific timed data freezes. Each SDM is formed from discipline-specific reports from across the scientific spectrum. This report describes the methods, analyses, and conclusions of the modelling team in the production of the SDM-Site Laxemar geological discrete-fracture network (DFN) model. The DFN builds upon the work of other geological models, including the deformation zone and rock domain models. The geological DFN is a statistical model for stochastically simulating rock fractures and minor deformation zones at a scale of less than 1,000 m (the lower cut-off of the DZ models). The geological DFN is valid within six distinct fracture domains inside the Laxemar local model subarea: FSM{sub C}, FSM{sub E}W007, FSM{sub N}, FSM{sub N}E005, FSM{sub S}, and FSM{sub W}. The models are built using data from detailed surface outcrop maps, geophysical lineament maps, and the cored borehole record at Laxemar. The conceptual model for the SDM-Site Laxemar geological DFN model revolves around the identification of fracture domains based on relative fracture set intensities, orientation clustering, and the regional tectonic framework (including deformation zones). A single coupled fracture size/fracture intensity concept (the Base Model) based on a Pareto (power-law) distribution for fracture sizes was chosen as the recommended parameterisation. A slew of alternative size-intensity models were also carried through the fracture analyses and into the uncertainty and model verification analyses. Uncertainty is modelled by analysing the effects on fracture intensity (P32) that alternative model cases can have. Uncertainty is parameterised as a ratio between the P32 of the

Geological discrete fracture network model for the Laxemar site. Site Descriptive Modelling. SDM-Site Laxemar

International Nuclear Information System (INIS)

La Pointe, Paul; Fox, Aaron; Hermanson, Jan; Oehman, Johan

2008-10-01

The Swedish Nuclear Fuel and Waste Management Company (SKB) is performing site characterization at two different locations, Forsmark and Laxemar, in order to locate a site for a final geologic repository for spent nuclear fuel. The program is built upon the development of Site Descriptive Models (SDMs) at specific timed data freezes. Each SDM is formed from discipline-specific reports from across the scientific spectrum. This report describes the methods, analyses, and conclusions of the modelling team in the production of the SDM-Site Laxemar geological discrete-fracture network (DFN) model. The DFN builds upon the work of other geological models, including the deformation zone and rock domain models. The geological DFN is a statistical model for stochastically simulating rock fractures and minor deformation zones at a scale of less than 1,000 m (the lower cut-off of the DZ models). The geological DFN is valid within six distinct fracture domains inside the Laxemar local model subarea: FSM C , FSM E W007, FSM N , FSM N E005, FSM S , and FSM W . The models are built using data from detailed surface outcrop maps, geophysical lineament maps, and the cored borehole record at Laxemar. The conceptual model for the SDM-Site Laxemar geological DFN model revolves around the identification of fracture domains based on relative fracture set intensities, orientation clustering, and the regional tectonic framework (including deformation zones). A single coupled fracture size/fracture intensity concept (the Base Model) based on a Pareto (power-law) distribution for fracture sizes was chosen as the recommended parameterisation. A slew of alternative size-intensity models were also carried through the fracture analyses and into the uncertainty and model verification analyses. Uncertainty is modelled by analysing the effects on fracture intensity (P32) that alternative model cases can have. Uncertainty is parameterised as a ratio between the P32 of the alternative model and the P

Ergonomic analysis of work in energy control plants: factors to be observed

International Nuclear Information System (INIS)

Rivas, R.

1987-01-01

To make evident the incidence of the technology modification due to the increasing automation of energy control plants on man, whose activity is limited to observation and control, with low working metabolism and high attention and concentration. The methodology is fundamentally based on the individual analysis of the factors affecting man. The following will be considered: a) load volume: the load volume generated by the above mentioned activity depends on the observation period, the number of indicators to be observed and the frequency of control activities; b) active participation: the lack of active participation due to a motionless task requires a constant yield disposition to develop an unusual activity; c) monotonous activity: the load is produced by maintaining a suitable physic-mental state through a volition effort; d) change of disposition: this component, which is not willingly admitted, changes the mechanism of compared functions during the day, following a biological law that depends from the hour; e) environment influence: the unfavorable physical influences, like climate, lack of light, noise, etc. also affect man. The analysis of mental load is specially important due to its influence on the performance, the accident risk and the safety of the system to be controlled. (Author)

Instrumenting the Conifers: A Look at Daily Tree Growth and Locally Observed Environmental Conditions Across Four Mountain Sites in the Central Great Basin, USA

Science.gov (United States)

Strachan, S.; Biondi, F.; Johnson, B. G.

2012-12-01

Tree growth is often used as a proxy for past environmental conditions or as an indicator of developing trends. Reconstructions of drought, precipitation, temperature, and other phenomena derived from tree-growth indices abound in scientific literature aimed at informing policy makers. Observations of tree recruitment or death in treeline populations are frequently tied to climatic fluctuation in cause-effect hypotheses. Very often these hypotheses are based on statistical relationships between annual-to-seasonal tree growth measurements and some environmental parameter measured or modeled off-site. Observation of daily tree growth in conjunction with in-situ environmental measurements at similar timescales takes us one step closer to quantifying the uncertainty in reconstruction or predictive studies. In four separate sites in two different mountain ranges in the central Great Basin, co-located observations of conifer growth activity and local atmospheric and soils conditions have been initiated. Species include Pinus longaeva (Great Basin bristlecone pine), Pinus flexilis (limber pine), Picea engelmannii (Engelmann spruce), Pinus monophylla (singleleaf pinyon pine), Pinus ponderosa (ponderosa pine), Abies concolor (white fir), and Pseudotsuga menziesii (Douglas-fir). Measurements of sub-hourly tree radial length change and sap flow activity are compared with a suite of in-situ observations including air temperature, precipitation, photosynthetically-active radiation (PAR), relative humidity, soil temperature, and soil moisture/water content. Subalpine study site located at 3360 m elevation in the Snake Range, Nevada

Work plan for preliminary investigation of organic constituents in ground water at the New Rifle site, Rifle, Colorado. Revision 2

International Nuclear Information System (INIS)

1996-01-01

A special study screening for Appendix 9 (40 CFR Part 264) analytes identified the New Rifle site as a target for additional screening for organic constituents. Because of this recommendation and the findings in a recent independent technical review, the US Department of Energy (DOE) has requested that the Technical Assistance Contractor (TAC) perform a preliminary investigation of the potential presence of organic compounds in the ground water at the New Rifle Uranium Mill Tailings Remedial Action (UMTRA) Project site, Rifle, Colorado. From 1958 to 1972, organic chemicals were used in large quantities during ore processing at the New Rifle site, and it is possible that some fraction was released to the environment. Therefore, the primary objective of this investigation is to determine whether organic chemicals used at the milling facility are present in the ground water. The purpose of this document is to describe the work that will be performed and the procedures that will be followed during installation of ground water well points at the New Rifle site. The selection of analytes and the procedures for collecting ground water samples for analysis of organic constituents are also described

Site-resolved imaging of a bosonic Mott insulator using ytterbium atoms

Science.gov (United States)

Miranda, Martin; Inoue, Ryotaro; Tambo, Naoki; Kozuma, Mikio

2017-10-01

We demonstrate site-resolved imaging of a strongly correlated quantum system without relying on laser cooling techniques during fluorescence imaging. We observe the formation of Mott shells in the insulating regime and realize thermometry in an atomic cloud. This work proves the feasibility of the noncooled approach and opens the door to extending the detection technology to new atomic species.

Optimizing interactive performance for long-distance remote observing

Science.gov (United States)

Kibrick, Robert; Allen, Steven L.; Conrad, Al; Wirth, Gregory D.

2006-06-01

Remote observing is the dominant mode of operation for both Keck Telescopes and their associated instruments. Over 90% of all Keck observations are carried out remotely from the Keck Headquarters in Waimea, Hawaii (located 40 kilometers from the telescopes on the summit of Mauna Kea), and this year represents the tenth anniversary of the start of Keck remote observing from Waimea. In addition, an increasing number of observations are now conducted by geographically-dispersed observing teams, with some team members working from Waimea while others collaborate from Keck remote observing facilities located in California. Such facilities are now operational on four campuses of the University of California and at the California Institute of Technology. Details of the motivation and planning for those facilities and the software architecture on which they were originally based are discussed in several previous reports. The most recent of those papers reported the results of various measurements of interactive performance as a function of alternative networking protocols (e.g., ssh, X, VNC) and software topologies. This report updates those results to reflect performance improvements that have occurred over the past two years as a result of upgrades to hardware, software, and network configurations at the respective sites. It also explores how the Keck remote observing effort has evolved over the past decade in response to the increased number and diversity of Keck instruments and the growing number of mainland remote observing sites.

Work stress and patient safety: observer-rated work stressors as predictors of characteristics of safety-related events reported by young nurses.

Science.gov (United States)

Elfering, A; Semmer, N K; Grebner, S

This study investigates the link between workplace stress and the 'non-singularity' of patient safety-related incidents in the hospital setting. Over a period of 2 working weeks 23 young nurses from 19 hospitals in Switzerland documented 314 daily stressful events using a self-observation method (pocket diaries); 62 events were related to patient safety. Familiarity of safety-related events and probability of recurrence, as indicators of non-singularity, were the dependent variables in multilevel regression analyses. Predictor variables were both situational (self-reported situational control, safety compliance) and chronic variables (job stressors such as time pressure, or concentration demands and job control). Chronic work characteristics were rated by trained observers. The most frequent safety-related stressful events included incomplete or incorrect documentation (40.3%), medication errors (near misses 21%), delays in delivery of patient care (9.7%), and violent patients (9.7%). Familiarity of events and probability of recurrence were significantly predicted by chronic job stressors and low job control in multilevel regression analyses. Job stressors and low job control were shown to be risk factors for patient safety. The results suggest that job redesign to enhance job control and decrease job stressors may be an important intervention to increase patient safety.

Safety inspections in construction sites: A systems thinking perspective.

Science.gov (United States)

Saurin, Tarcisio Abreu

2016-08-01

Although safety inspections carried out by government officers are important for the prevention of accidents, there is little in-depth knowledge on their outcomes and processes leading to these. This research deals with this gap by using systems thinking (ST) as a lens for obtaining insights into safety inspections in construction sites. Thirteen case studies of sites with prohibited works were carried out, discussing how four attributes of ST were used in the inspections. The studies were undertaken over 6 years, and sources of evidence involved participant observation, direct observations, analysis of documents and interviews. Two complementary ways for obtaining insights into inspections, based on ST, were identified: (i) the design of the study itself needs to be in line with ST; and (ii) data collection and analysis should focus on the agents involved in the inspections, the interactions between agents, the constraints and opportunities faced by agents, the outcomes of interactions, and the recommendations for influencing interactions. Copyright © 2015 Elsevier Ltd. All rights reserved.

The perception of nuclear risks on French sites: social actors and rumors

International Nuclear Information System (INIS)

Timbal-Duclaux, L.

1983-01-01

This study summarizes the main French researchs on people living close to nuclear plants and their perception of nuclear risks. The ethnological approach was utilized, consisting in an observer living long periods of time on the site. It shows the existence of a ''psychogeographical'' zone in which people fell concerned by the building of the plant. This event reinforce the existing tensions between the social actors in the field of the site. The plant is seen as a ''big work'' ''eating'' land from agriculture and recreation, mixed with a nuclear thing mysterious and dangerous. Perceptions and rumors are greatly varying depending time and space. These results may be applied to a better siting of the plants [fr

Radiation safety for site radiography

International Nuclear Information System (INIS)

1986-01-01

This guidance is an update of the 1975 Code of Practice for Site Radiography and is for the use of employers and their radiographers who carry out site work. The subject is discussed under the following headings: Administrative organization, Personnel requirements, Equipment (x-ray and gamma-ray equipment, security, pipeline crawler equipment and safety equipment) Work methods and monitoring, Carriage of sources, Contingency plans, Legal considerations. (U.K.)

Remedial investigation/feasibility study work plan for the 100-BC-5 Operable Unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-04-01

Four areas of the Hanford Site (the 100, 200, 300 and 1100 Areas) have been included on the US Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Figure 1-1 shows the location of these areas. Under the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement, Ecology et al. 1990a), signed by the Washington State Department of Ecology (Ecology), EPA, and the US Department of Energy (DOE), more than 1,000 inactive waste disposal and unplanned release sites on the Hanford Site have been grouped into a number of source and groundwater operable units. These operable units contain contamination in the form of hazardous waste, radioactive/hazardous mixed waste and other CERCLA hazardous substances. Also included in the Tri-Party Agreement are 55 Resource Conservation and Recovery Act (RCRA) treatment, storage, or disposal (TSD) facilities that will be closed or permitted to operate in accordance with RCRA regulations, under the authority of Chapter 173-303 Washington Administrative Code (WAC). Some of the TSD facilities are included in the operable units. This work plant and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the CERCLA remedial investigation/feasibility study (RI/FS) for the 100-BC-5 operable unit. The 100-B/C Area consists of the 100-BC-5 groundwater operable unit and four source operable units. The 100-BC-5 operable unit includes all contamination found in the aquifer soils and water beneath the 100-B/C Area. Source operable units include facilities and unplanned release sites that are potential sources of contamination

Parent-Adolescent Relationship Qualities, Internal Working Models, and Styles as Predictors of Adolescents’ Observed Interactions with Friends

Science.gov (United States)

Shomaker, Lauren B.; Furman, Wyndol

2010-01-01

This study examined how current parent-adolescent relationship qualities and adolescents’ representations of relationships with parents were related to friendship interactions in 200 adolescent-close friend dyads. Adolescents and friends were observed discussing problems during a series of structured tasks. Negative interactions with mothers were significantly related to adolescents’ greater conflict with friends, poorer focus on tasks, and poorer communication skills. Security of working models (as assessed by interview) was significantly associated with qualities of friendship interactions, whereas security of attachment styles (as assessed by questionnaire) was not. More dismissing (vs. secure) working models were associated with poorer focus on problem discussions and weaker communication skills with friends, even after accounting for gender differences and current parent-adolescent relationship qualities. We discuss possible mechanisms for the observed links between dimensions of parent-adolescent relationships and friendships. We also consider methodological and conceptual differences between working model and style measures of attachment representations. PMID:20174459

Site classification for National Strong Motion Observation Network System (NSMONS) stations in China using an empirical H/V spectral ratio method

Science.gov (United States)

Ji, Kun; Ren, Yefei; Wen, Ruizhi

2017-10-01

Reliable site classification of the stations of the China National Strong Motion Observation Network System (NSMONS) has not yet been assigned because of lacking borehole data. This study used an empirical horizontal-to-vertical (H/V) spectral ratio (hereafter, HVSR) site classification method to overcome this problem. First, according to their borehole data, stations selected from KiK-net in Japan were individually assigned a site class (CL-I, CL-II, or CL-III), which is defined in the Chinese seismic code. Then, the mean HVSR curve for each site class was computed using strong motion recordings captured during the period 1996-2012. These curves were compared with those proposed by Zhao et al. (2006a) for four types of site classes (SC-I, SC-II, SC-III, and SC-IV) defined in the Japanese seismic code (JRA, 1980). It was found that an approximate range of the predominant period Tg could be identified by the predominant peak of the HVSR curve for the CL-I and SC-I sites, CL-II and SC-II sites, and CL-III and SC-III + SC-IV sites. Second, an empirical site classification method was proposed based on comprehensive consideration of peak period, amplitude, and shape of the HVSR curve. The selected stations from KiK-net were classified using the proposed method. The results showed that the success rates of the proposed method in identifying CL-I, CL-II, and CL-III sites were 63%, 64%, and 58% respectively. Finally, the HVSRs of 178 NSMONS stations were computed based on recordings from 2007 to 2015 and the sites classified using the proposed method. The mean HVSR curves were re-calculated for three site classes and compared with those from KiK-net data. It was found that both the peak period and the amplitude were similar for the mean HVSR curves derived from NSMONS classification results and KiK-net borehole data, implying the effectiveness of the proposed method in identifying different site classes. The classification results have good agreement with site classes

ORCHIDEE-CNP: Site-Scale Evaluation against Observations from a Soil Formation Chronosequence in Hawaii

Science.gov (United States)

Goll, D. S.; Vuichard, N.; Maignan, F.; Jornet-Puig, A.; Sardans, J.; Peng, S.; Sun, Y.; Kvakić, M.; Guimberteau, M.; Guenet, B.; Zaehle, S.; Penuelas, J.; Jannssens, I.; Ciais, P.

2017-12-01

Land surface models rarely incorporate the terrestrial phosphorus cycle and its interactions with the carbon cycle, despite the extensive scientific debate about the importance of nitrogen and phosphorus supply for future land carbon uptake. We describe a representation of the terrestrial phosphorus cycle for the land surface model ORCHIDEE, and evaluate it with data from nutrient manipulation experiments along a soil formation chronosequence in Hawaii. ORCHIDEE accounts for influence of nutritional state of vegetation on tissue nutrient concentrations, photosynthesis, plant growth, biomass allocation, biochemical (phosphatase-mediated) mineralization and biological nitrogen fixation. Changes in nutrient content (quality) of litter affect the carbon use efficiency of decomposition and in return the nutrient availability to vegetation. The model explicitly accounts for root zone depletion of phosphorus as a function of root phosphorus uptake and phosphorus transport from soil to the root surface. The model captures the observed differences in the foliage stoichiometry of vegetation between an early (300yr) and a late stage (4.1 Myr) of soil development. The contrasting sensitivities of net primary productivity to the addition of either nitrogen, phosphorus or both among sites are in general reproduced by the model. As observed, the model simulates a preferential stimulation of leaf level productivity when nitrogen stress is alleviated, while leaf level productivity and leaf area index are stimulated equally when phosphorus stress is alleviated. The nutrient use efficiencies in the model are lower as observed primarily due to biases in the nutrient content and turnover of woody biomass.

Observations on Faults and Associated Permeability Structures in Hydrogeologic Units at the Nevada Test Site

Energy Technology Data Exchange (ETDEWEB)

Prothro, Lance B.; Drellack, Sigmund L.; Haugstad, Dawn N.; Huckins-Gang, Heather E.; Townsend, Margaret J.

2009-03-30

Observational data on Nevada Test Site (NTS) faults were gathered from a variety of sources, including surface and tunnel exposures, core samples, geophysical logs, and down-hole cameras. These data show that NTS fault characteristics and fault zone permeability structures are similar to those of faults studied in other regions. Faults at the NTS form complex and heterogeneous fault zones with flow properties that vary in both space and time. Flow property variability within fault zones can be broken down into four major components that allow for the development of a simplified, first approximation model of NTS fault zones. This conceptual model can be used as a general guide during development and evaluation of groundwater flow and contaminate transport models at the NTS.

Site selection

International Nuclear Information System (INIS)

Olsen, C.W.

1983-07-01

The conditions and criteria for selecting a site for a nuclear weapons test at the Nevada Test Site are summarized. Factors considered are: (1) scheduling of drill rigs, (2) scheduling of site preparation (dirt work, auger hole, surface casing, cementing), (3) schedule of event (when are drill hole data needed), (4) depth range of proposed W.P., (5) geologic structure (faults, Pz contact, etc.), (6) stratigraphy (alluvium, location of Grouse Canyon Tuff, etc.), (7) material properties (particularly montmorillonite and CO 2 content), (8) water table depth, (9) potential drilling problems (caving), (10) adjacent collapse craters and chimneys, (11) adjacent expended but uncollapsed sites, (12) adjacent post-shot or other small diameter holes, (13) adjacent stockpile emplacement holes, (14) adjacent planned events (including LANL), (15) projected needs of Test Program for various DOB's and operational separations, and (16) optimal use of NTS real estate

RCRA facility investigation/corrective measures study work plan for the 100-DR-1 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-09-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Under the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement, Ecology et. al. 1990a), signed by the Washington State Department of Ecology (Ecology), EPA, and the US Department of Energy (DOE), more than 1,000 inactive waste disposal and unplanned release sites on the Hanford Site have been grouped into a number of source and groundwater operable units. These operable units contain contamination in the form of hazardous waste, radioactive/hazardous mixed waste, and other CERCLA hazardous substances. Also included in the Tri-Party Agreement are 55 Resource Conservation and Recovery Act (RCRA) treatment, storage, or disposal (TSD) facilities that will be closed or permitted to operate in accordance with RCRA regulations. Some of the TSD facilities are included in the operable units. This work plan and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the RCRA facility investigation/corrective measures study (RFI/CMS) for the 100-DR-1 source operable unit Source operable units include facilities and unplanned release sites that are potential sources of contamination

Evaluation of team lifting on work demands, workload and workers' evaluation: an observational field study.

Science.gov (United States)

Visser, Steven; van der Molen, Henk F; Kuijer, P Paul F M; Hoozemans, Marco J M; Frings-Dresen, Monique H W

2014-11-01

The objective of this study was to assess differences in work demands, energetic workload and workers' discomfort and physical effort in two regularly observable workdays in ironwork; one where loads up to 50kg were handled with two persons manually (T50) and one where loads up to 100kg were handled manually with four persons (T100). Differences between these typical workdays were assessed with an observational within-subject field study of 10 ironworkers. No significant differences were found for work demands, energetic workload or discomfort between T50 and T100 workdays. During team lifts, load mass exceeded 25kg per person in 57% (T50 workday) and 68% (T100 workday) of the lifts. Seven ironworkers rated team lifting with two persons as less physically demanding compared with lifting with four persons. When loads heavier than 25kg are lifted manually with a team, regulations of the maximum mass weight are frequently violated. Loads heavier than 25kg are frequently lifted during concrete reinforcement work and should be lifted by a team of persons. However, the field study showed that loads above 25kg are most of the time not lifted with the appropriate number of workers. Therefore, loads heavier than 25kg should be lifted mechanically. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

A future for nuclear sites beyond their service life. Nuclear site value development

International Nuclear Information System (INIS)

2008-01-01

As the nuclear industry moves into a new development phase, many facilities built in the fifties and sixties are reaching the end of their service life. Dismantling them and rehabilitating the sites on which they stand is a major industrial challenge which will give rise to a number of new projects. AREVA has more than 20 years' experience in these highly technical fields. As more and more sites reach the end of their service life, AREVA considers nuclear site value development as a fully-fledged industrial activity. The group's competencies in this field have been grouped together to form a dedicated entity: the Nuclear Site Value Development Business Unit, created in 2008. Several billion euros are invested in site value development projects which are far-reaching and complex, and often last for several decades. Long before work actually begins, lengthy studies and preparations are required to schedule operations, select the techniques to be used and optimize costs and deadlines. The Nuclear Site Value Development BU is currently working on four major projects involving its own facilities and those of the CEA: - La Hague: dismantling of the first generation of used fuel recycling facilities. Between 1966 and 1998, almost 5,000 tons of used fuel from graphite-moderated gas-cooled reactors, 4,500 tons of light water reactor fuel, as well as fuel from fast reactors and research reactors, were treated at UP2 400, the very first industrial recycling plant on the La Hague site. - Marcoule: first-time dismantling of a recycling plant. 1,000 rooms to be cleaned up, 30,000 tons of waste to be treated, 30 years of work. - Cadarache: first-time dismantling of a Mox fuel fabrication plant. The Cadarache plant was commissioned in 1962 to fabricate fuel for fast reactors; this was followed by MOX fuel for light water reactors, an activity which continued until the plant was shut down in 2003. - Annecy and Veurey: giving a new lease of life to former industrial sites in built

Coronal structures and particle acceleration studies from radioelectric and optical observations

International Nuclear Information System (INIS)

Axisa, Francois.

1974-01-01

The problem of acceleration outside of and during eruptions is studied from the association of type III radioelectric jumps with the chromosphere activity observed in absorption and emission of the Hα line. In addition the mean corona structure is investigated from observation of the slowly variable metric wave component in connection with coronal filaments and jets, and by type III emission in relation to the eruptive sites of complex active regions. Most of the experimental material comes from observations made with the Nancay East-West radioheliograph, which works on 169 MHz and optical observations carried out at the Meudon Observatory on the chromosphere and on photosphere magnetic fields [fr

Bedrock hydrogeology Forsmark. Site descriptive modelling, SDM-Site Forsmark

Energy Technology Data Exchange (ETDEWEB)

Follin, Sven (SF GeoLogic AB, Taeby (Sweden))

2008-12-15

The Swedish Nuclear Fuel and Waste Management Company (SKB) has conducted site investigations at two different locations, the Forsmark and Laxemar-Simpevarp areas, with the objective of siting a final repository for spent nuclear fuel according to the KBS-3 concept. Site characterisation should provide all data required for an integrated evaluation of the suitability of the investigated site and an important component in the characterisation work is the development of a hydrogeological model. The hydrogeological model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It also provides input to the safety assessment. Another important use of the hydrogeological model is in the environmental impact assessment. This report presents the understanding of the hydrogeological conditions of the bedrock at Forsmark reached following the completion of the surface-based investigations and provides a summary of the bedrock hydrogeological model and the underlying data supporting its development. It constitutes the main reference on bedrock hydrogeology for the site descriptive model concluding the surface-based investigations at Forsmark, SDM-site, and is intended to describe the hydraulic properties and hydrogeological conditions of the bedrock at the site and to give the information essential for demonstrating understanding

The MS@Work study: a 3-year prospective observational study on factors involved with work participation in patients with relapsing-remitting Multiple Sclerosis.

Science.gov (United States)

van der Hiele, Karin; van Gorp, Dennis A M; Heerings, Marco A P; van Lieshout, Irma; Jongen, Peter J; Reneman, Michiel F; van der Klink, Jac J L; Vosman, Frans; Middelkoop, Huub A M; Visser, Leo H

2015-08-12

Multiple Sclerosis (MS) is the most common cause of neurological disability in young and middle-aged adults. At this stage in life most people are in the midst of their working career. The majority of MS patients are unable to retain employment within 10 years from disease onset. Leading up to unemployment, many may experience a reduction in hours or work responsibilities and increased time missed from work. The MS@Work study examines various factors that may influence work participation in relapsing-remitting MS patients, including disease-related factors, the working environment and personal factors. The MS@Work study is a multicenter, 3-year prospective observational study on work participation in patients with relapsing-remitting MS. We aim to include 350 patients through 15-18 MS outpatient clinics in the Netherlands. Eligible participants are 18 years and older, and either currently employed or within three years since their last employment. At baseline and after 1, 2 and 3 years, the participants are asked to complete online questionnaires (including questions on work participation, work problems and accommodations, cognitive and physical ability, anxiety, depression, psychosocial stress, quality of life, fatigue, empathy, personality traits and coping strategies) and undergo cognitive and neurological examinations. After six months, patients are requested to only complete online questionnaires. Patient perspectives on maintaining and improving work participation and reasons to stop working are gathered through semi-structured interviews in a sub-group of patients. Prospective studies with long-term follow-up on work participation in MS are rare, or take into account a limited number of factors. The MS@Work study provides a 3-year follow-up on various factors that may influence work participation in patients with relapsing-remitting MS. We aim to identify factors that relate to job loss and to provide information about preventative measures for physicians

Cyberinfrastructure Initiatives of the Committee on Earth Observation Satellites (CEOS) Working Group on Information Systems and Services (WGISS)

Science.gov (United States)

McDonald, K. R.; Faundeen, J. L.; Petiteville, I.

2005-12-01

The Committee on Earth Observation Satellites (CEOS) was established in 1984 in response to a recommendation from the Economic Summit of Industrialized Nations Working Group on Growth, Technology, and Employment's Panel of Experts on Satellite Remote Sensing. CEOS participants are Members, who are national or international governmental organizations who operate civil spaceborne Earth observation satellites, and Associates who are governmental organizations with civil space programs in development or international scientific or governmental bodies who have an interest in and support CEOS objectives. The primary objective of CEOS is to optimize benefits of satellite Earth observations through cooperation of its participants in mission planning and in development of compatible data products, formats, services, applications and policies. To pursue its objectives, CEOS establishes working groups and associated subgroups that focus on relevant areas of interest. While the structure of CEOS has evolved over its lifetime, today there are three permanent working groups. One is the Working Group on Calibration and Validation that addresses sensor-specific calibration and validation and geophysical parameter validation. A second is the Working Group on Education, Training, and Capacity Building that facilitates activities that enhance international education and training in Earth observation techniques, data analysis, interpretation and applications, with a particular focus on developing countries. The third permanent working group is the Working Group on Information Systems and Services (WGISS). The purpose of WGISS is to promote collaboration in the development of the systems and services based on international standards that manage and supply the Earth observation data and information from participating agencies' missions. WGISS places great emphasis on the use of demonstration projects involving user groups to solve the critical interoperability issues associated with the

Plasmodium sporozoites trickle out of the injection site.

Science.gov (United States)

Yamauchi, Lucy Megumi; Coppi, Alida; Snounou, Georges; Sinnis, Photini

2007-05-01

Plasmodium sporozoites make a remarkable journey from the skin, where they are deposited by an infected Anopheline mosquito, to the liver, where they invade hepatocytes and develop into exoerythrocytic stages. Although much work has been done to elucidate the molecular mechanisms by which sporozoites invade hepatocytes, little is known about the interactions between host and parasite before the sporozoite enters the blood circulation. It has always been assumed that sporozoites rapidly exit the injection site, making their interactions with the host at this site, brief and difficult to study. Using quantitative PCR, we determined the kinetics with which sporozoites leave the injection site and arrive in the liver and found that the majority of infective sporozoites remain in the skin for hours. We then performed sub-inoculation experiments which confirmed these findings and showed that the pattern of sporozoite exit from the injection site resembles a slow trickle. Last, we found that drainage of approximately 20% of the sporozoite inoculum to the lymphatics is associated with a significant enlargement of the draining lymph node, a response not observed after intravenous inoculation. These findings indicate that there is ample time for host and parasite to interact at the inoculation site and are of relevance to the pre-erythrocytic stage malaria vaccine effort.

Online catalog of world-wide test sites for the post-launch characterization and calibration of optical sensors

Science.gov (United States)

Chander, G.; Christopherson, J.B.; Stensaas, G.L.; Teillet, P.M.

2007-01-01

In an era when the number of Earth-observing satellites is rapidly growing and measurements from these sensors are used to answer increasingly urgent global issues, it is imperative that scientists and decision-makers can rely on the accuracy of Earth-observing data products. The characterization and calibration of these sensors are vital to achieve an integrated Global Earth Observation System of Systems (GEOSS) for coordinated and sustained observations of Earth. The U.S. Geological Survey (USGS), as a supporting member of the Committee on Earth Observation Satellites (CEOS) and GEOSS, is working with partners around the world to establish an online catalog of prime candidate test sites for the post-launch characterization and calibration of space-based optical imaging sensors. The online catalog provides easy public Web site access to this vital information for the global community. This paper describes the catalog, the test sites, and the methodologies to use the test sites. It also provides information regarding access to the online catalog and plans for further development of the catalog in cooperation with calibration specialists from agencies and organizations around the world. Through greater access to and understanding of these vital test sites and their use, the validity and utility of information gained from Earth remote sensing will continue to improve. Copyright IAF/IAA. All rights reserved.

POVERTY AND COLOR IN CHILDREN'S EDUCATION: NECESSARY OBSERVATIONS TO THE WORK OF SCHOLAR INCLUSION

Directory of Open Access Journals (Sweden)

Deise Maria Santos de Aguiar

2013-07-01

Full Text Available This article presents a part of the results of a Master’s research in which the issue of children who face differentiation and inequality processes in their relationships inside school is investigated in terms of its ties to socioeconomic conditions, as well as color/race definitions. The investigation was made using the children’s own perception. The article aims to contribute to the discussion towards both the initial and continuous formation of professionals working at schools, those who should be able to observe and even question their own manners of acting and feeling while working, identifying prejudices and situations of exclusion/marginalization which they may help to produce in the school routine. The research used the ethnographic method, focusing on the children’s narratives, color/race classifications, socioeconomic surveys, field observations and interviews with the children and the teachers. The analysis of the results indicates the need of a discussion of the educational culture and its important role in the process of building identities, since it was possible to identify the daily practices that discriminate and exclude children who should supposedly find, at school, an inclusive environment able to build a positive image of themselves, as well as the African-American population and its aesthetics and culture.

Hydroelectric potential of existing works in the Ardennes district - Preliminary study report, Feasibility study for the development of La Ferte-sur-Chiers, Feasibility study for the development of the Montherme site

International Nuclear Information System (INIS)

2010-02-01

A first document reports the analysis of five existing non-hydroelectric works. The objective is to see whether it is possible to equip them with a hydroelectric installation. For each of them, the report proposes a description of the site, a pre-diagnosis, a discussion of the regulatory framework, a hydrological analysis, a production assessment, and comments about a possible site rehabilitation. The next documents report feasibility studies performed for two of these sites. Each report presents the site and the adopted methodology, hydrological data, an analysis of the available height of fall, an analysis of environmental constraints, studied scenarios, a calculation of the possible production, a description of works to be performed, and a financial analysis

Cross-calibration of Medium Resolution Earth Observing Satellites by Using EO-1 Hyperion-derived Spectral Surface Reflectance from "Lunar Cal Sites"

Science.gov (United States)

Ungar, S.

2017-12-01

Over the past 3 years, the Earth Observing-one (EO-1) Hyperion imaging spectrometer was used to slowly scan the lunar surface at a rate which results in up to 32X oversampling to effectively increase the SNR. Several strategies, including comparison against the USGS RObotic Lunar Observatory (ROLO) mode,l are being employed to estimate the absolute and relative accuracy of the measurement set. There is an existing need to resolve discrepancies as high as 10% between ROLO and solar based calibration of current NASA EOS assets. Although the EO-1 mission was decommissioned at the end of March 2017, the development of a well-characterized exoatmospheric spectral radiometric database, for a range of lunar phase angles surrounding the fully illuminated moon, continues. Initial studies include a comprehensive analysis of the existing 17-year collection of more than 200 monthly lunar acquisitions. Specific lunar surface areas, such as a lunar mare, are being characterized as potential "lunar calibration sites" in terms of their radiometric stability in the presence of lunar nutation and libration. Site specific Hyperion-derived lunar spectral reflectance are being compared against spectrographic measurements made during the Apollo program. Techniques developed through this activity can be employed by future high-quality orbiting imaging spectrometers (such as HyspIRI and EnMap) to further refine calibration accuracies. These techniques will enable the consistent cross calibration of existing and future earth observing systems (spectral and multi-spectral) including those that do not have lunar viewing capability. When direct lunar viewing is not an option for an earth observing asset, orbiting imaging spectrometers can serve as transfer radiometers relating that asset's sensor response to lunar values through near contemporaneous observations of well characterized stable CEOS test sites. Analysis of this dataset will lead to the development of strategies to ensure more

Early Site Permit Demonstration Program: Siting Guide, Site selection and evaluation criteria for an early site permit application. Revision 1

Energy Technology Data Exchange (ETDEWEB)

1993-03-24

In August 1991, the Joint Contractors came to agreement with Sandia National Laboratories (SNL) and the Department of Energy (DOE) on a workscope for the cost-shared Early Site Permit Demonstration Program. One task within the scope was the development of a guide for site selection criteria and procedures. A generic Siting Guide his been prepared that is a roadmap and tool for applicants to use developing detailed siting plans for their specific region of the country. The guide presents three fundamental principles that, if used, ensure a high degree of success for an ESP applicant. First, the site selection process should take into consideration environmentally diverse site locations within a given region of interest. Second, the process should contain appropriate opportunities for input from the public. Third, the process should be applied so that it is clearly reasonable to an impartial observer, based on appropriately selected criteria, including criteria which demonstrate that the site can host an advanced light water reactor (ALWR). The Siting Guide provides for a systematic, comprehensive site selection process in which three basic types of criteria (exclusionary, avoidance, and suitability) are presented via a four-step procedure. It provides a check list of the criteria for each one of these steps. Criteria are applied qualitatively, as well as presented numerically, within the guide. The applicant should use the generic guide as an exhaustive checklist, customizing the guide to his individual situation.

Assessing hospital disaster preparedness: a comparison of an on-site survey, directly observed drill performance, and video analysis of teamwork.

Science.gov (United States)

Kaji, Amy H; Langford, Vinette; Lewis, Roger J

2008-09-01

There is currently no validated method for assessing hospital disaster preparedness. We determine the degree of correlation between the results of 3 methods for assessing hospital disaster preparedness: administration of an on-site survey, drill observation using a structured evaluation tool, and video analysis of team performance in the hospital incident command center. This was a prospective, observational study conducted during a regional disaster drill, comparing the results from an on-site survey, a structured disaster drill evaluation tool, and a video analysis of teamwork, performed at 6 911-receiving hospitals in Los Angeles County, CA. The on-site survey was conducted separately from the drill and assessed hospital disaster plan structure, vendor agreements, modes of communication, medical and surgical supplies, involvement of law enforcement, mutual aid agreements with other facilities, drills and training, surge capacity, decontamination capability, and pharmaceutical stockpiles. The drill evaluation tool, developed by Johns Hopkins University under contract from the Agency for Healthcare Research and Quality, was used to assess various aspects of drill performance, such as the availability of the hospital disaster plan, the geographic configuration of the incident command center, whether drill participants were identifiable, whether the noise level interfered with effective communication, and how often key information (eg, number of available staffed floor, intensive care, and isolation beds; number of arriving victims; expected triage level of victims; number of potential discharges) was received by the incident command center. Teamwork behaviors in the incident command center were quantitatively assessed, using the MedTeams analysis of the video recordings obtained during the disaster drill. Spearman rank correlations of the results between pair-wise groupings of the 3 assessment methods were calculated. The 3 evaluation methods demonstrated

Emergencies and acute diseases in the collected works of Hippocrates: observation, examination, prognosis, therapy.

Science.gov (United States)

Askitopoulou, Helen; Stefanakis, Georgios; Astyrakaki, Elisabeth E; Papaioannou, Alexandra; Agouridakis, Panagiotis

2016-12-01

The collected works οf Hippocrates include a wealth of references to emergencies and acute conditions; if the physician could treat these, he would be considered superior to his colleagues. Works most relevant to current Emergency Medicine are presented. They indicate Hippocrates' remarkable insight and attention to the value of close observation, meticulous clinical examination, and prognosis. Hippocrates and his followers disdained mystery and were not satisfied until they had discovered a rational cause to diseases. They assigned great significance to distressing signs and symptoms - the famous Hippocratic face, the breathing pattern, pain, seizures, opisthotonus - pointing to a fatal outcome, which they reported to their patient. The principles of treatment of emergencies, such as angina, haemorrhage, empyema, ileus, shoulder dislocations and head injuries, are astonishingly similar to the ones used nowadays.

History of creation of Semipalatinsk test nuclear site. Chapter 1

International Nuclear Information System (INIS)

1999-01-01

In 1949 August USSR's Government adopted decision about creation of nuclear site with conditional name Uchebnyj polygon 2. For its building was chosen territory in 140 km from Semipalatinsk city. Semipalatinsk test site consists of the land of three regions: Semipalatinsk, Pavlodar, Karaganda and it occupies 18,500 km 2 of fertile land, rich with minerals. Now this territory was alienated from national using. Polygon was complex object and it incorporated three main zones: Opytnoe Pole, zone of radiation safety, site Sh. Opytnoe Pole was equipped by special constructions ensuring nuclear test conducting, its observing and registration of physical measurements and occupied 2,300 km 2 . Around of the Opytnoe Pole is situated zone of radiation safety with area 45 thousand ha. Site Sh was situated in 14 km from center of Opytnoe Pole and it was intended for distribution of individual protection devices, dosimeters and for conducting of dis-activation and sanitary works. History of the site creation is connected with building of Kurchatov city. In dozen and hundred of kilometers from Kurchatov city there were top secret objects: site Balapan with total area 100,000 ha intended for conducting of nuclear tests in wells with threshold capacity 100-200 kt. Here simultaneously with main problems on the site the military-applied works were conducted on mechanics, physics of combustion, simulation of Earthquakes and determination of seismic stability of buildings and constructions. Research site Degelen with total area 33,100 ha which has been used for underground testing of nuclear charges with small capacity. Site 10 one of large research technical complex on which two reactor units were installed. Main tasks of the complex were as follows: high-temperature fuel materials testing, conducting of fundamental researches in field of physics of fissile products, thermal physics and gas hydrodynamics. On site M a laboratory base for radiochemical, radiological and chemical

Management strategy for site characterization at candidate HLW repository sites

International Nuclear Information System (INIS)

Bartlett, J.W.

1988-01-01

This paper describes a management strategy for HLW repository site characterization which is aimed at producing an optimal characterization trajectory for site suitability and licensing evaluations. The core feature of the strategy is a matrix of alternative performance targets and alternative information-level targets which can be used to allocate and justify program effort. Strategies for work concerning evaluation of expected and disrupted repository performance are distinguished, and the need for issue closure criteria is discussed

Ocean Dredged Material Disposal Site (ODMDS) Authorization and Short-Term FATE (STFATE) Model Analysis: 2014-2015 Working Group Findings Report

Science.gov (United States)

2016-03-01

fractions A grain size or sieve analysis typically yields the mass fraction of each particle size class after dispersing all of the material. However...ER D C TR -1 6- 2 Ocean Dredged Material Disposal Site (ODMDS) Authorization and Short-Term FATE (STFATE) Model Analysis 2014 – 2015...Term FATE (STFATE) Model Analysis 2014 – 2015 Working Group Findings Report Jase D. Ousley Coastal and Hydraulics Laboratory U.S. Army Engineer

On-site and off-site atmospheric PBDEs in an electronic dismantling workshop in south China: Gas-particle partitioning and human exposure assessment

International Nuclear Information System (INIS)

An Taicheng; Zhang Delin; Li Guiying; Mai Bixian; Fu Jiamo

2011-01-01

Gas samples and total suspended particle during work and off work time were investigated on-site and off-site electronic waste dismantling workshop (I- and O-EWDW), then compared with plastic recycling workshop (PRW) and waste incineration plant (WIP). TSP concentrations and total PBDE were 0.36-2.21 mg/m 3 and 27-2975 ng/m 3 at different workshops, respectively. BDE-47, -99, and -209 were major ΣPBDE congeners at I-EWDW and WIP, while BDE-209 was only dominant congener in PRW and control sites during work time and all sites during off work time. The gas-particle partitioning result was well correlated with the subcooled liquid vapor pressure for all samples, except for WIP and I-EDWD, at park during work time, and residential area during off work time. The predicted urban curve fitted well with measured φ values at O-DEWD during work time, whereas it was slightly overestimated or underestimated for others. Exposure assessment revealed the highest exposure site was I-EDWD. - Highlights: → On- and off-site atmospheric PBDEs was monitored in e-waste dismantling workshops in south China. → The gas-particle partitioning result was well correlated with the subcooled liquid vapor pressure for some samples. → Exposure assessment revealed that workers in I-EDWD were the highest exposure population. - The findings of this study may serve as a valuable reference for future risk assessment and environmental management in Guiyu, South China.

A socio-cognitive strategy to address farmers' tolerance of high risk work: Disrupting the effects of apprenticeship of observation.

Science.gov (United States)

Mazur, Joan M; Westneat, Susan

2017-02-01

Why do generations of farmers tolerate the high-risk work of agricultural work and resist safe farm practices? This study presents an analysis inspired by empirical data from studies conducted from 1993 to 2012 on the differing effects of farm safety interventions between participants who live or work on farms and those who don't, when both were learning to be farm safety advocates. Both groups show statistically significant gains in knowledge and behavioral change proxy measures. However, non-farm participants' gains consistently outstripped their live/work farm counterparts. Drawing on socio-cultural perspectives, a grounded theory qualitative analysis focused on identifying useful constructs to understand the farmers' resistance to adopt safety practices. Understanding apprenticeships of observation and its relation to experiential learning over time can expose sources of deeply anchored beliefs and how they operate insidiously to promote familiar, albeit unsafe farming practices. The challenge for intervention-prevention programs becomes how to disrupt what has been learned during these apprenticeships of observation and to address what has been obscured during this powerful socialization process. Implications focus on the design and implementation of farm safety prevention and education programs. First, farm safety advocates and prevention researchers need to attend to demographics and explicitly explore the prior experiences and background of safety program participants. Second, farm youth in particular need to explore, explicitly, their own apprenticeships of observations, preferably through the use of new social media and or digital forms of expression, resulting in a story repair process. Third, careful study of the organization of work and farm experiences and practices need to provide the foundations for intervention programs. Finally, it is crucial that farm safety programs understand apprenticeships of observation are generational and ongoing over time

Disposal of the radioactive contaminated soils from the NPP site

International Nuclear Information System (INIS)

Matusek, I.; Plsko, J.; Sajtlava, M.; Hulla, J.; Kovacs, T.

2004-01-01

Disposal of contaminated soils at site of NPP is one of the most important task within the frame of research and development tasks of the NPP decommissioning. The works within this field can be seen in several areas. Considered soil activity monitoring, observation of its geo-technical and geo-chemical parameters, volume balance, research of the radio nuclides behaviour in the soil and simulation of their influence on the surrounding environment with special emphasis on underground water, project studies and construction of the disposal facility for contaminated soils. This work presents overview of gained results in the mentioned areas of the research and development. (author)

Site scientific mission plan for the southern Great Plains CART site, January--June 1998

Energy Technology Data Exchange (ETDEWEB)

Peppler, R.A.; Lamb, P.J. [Univ. of Oklahoma, Norman, OK (United States). Cooperative Inst. for Mesoscale Meteorological Studies; Sisterson, D.L. [Argonne National Lab., IL (United States). Environmental Research Div.

1998-01-01

The Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site is designed to help satisfy the data needs of the Atmospheric Radiation Measurement (ARM) Program Science Team. The primary purpose of this site scientific mission plan is to provide guidance for the development of plans for site operations. It also provides information on current plans to the ARM functional teams (Management Team, Data and Science Integration Team, Operations Team, and Instrument Team) and serves to disseminate the plans more generally within the ARM Program and among the members of the Science Team. This document includes a description of the operational status of the site and the primary site activities envisioned, together with information concerning approved and proposed intensive observation periods (IOPs). The primary users of this document are the Site operator, the Site Scientist Team (SST), the Science Team through the ARM Program science director, the ARM Program Experiment Center, and the aforementioned ARM Program functional teams. This plan is a living document that is updated and reissued every six months as the observational facilities are developed, tested, and augmented and as priorities are adjusted in response to developments in scientific planning and understanding.

General siting study 95. Siting of a deep repository for spent nuclear fuel

International Nuclear Information System (INIS)

1995-10-01

General Siting Study 95 is a detailed description of the work carried out to put the siting of a deep repository in a national and regional context. The report is based on SKB's siting factors, which have been applied on a national scale. Different factors of importance or of possible importance for the long-term radiological safety, technology, land and environment as well as society are described and evaluated. This report is the overall description on general siting studies which the government considered that SKB should report in connection with the RD and D Programme 95. 121 refs, 40 figs

General siting study 95. Siting of a deep repository for spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

General Siting Study 95 is a detailed description of the work carried out to put the siting of a deep repository in a national and regional context. The report is based on SKB`s siting factors, which have been applied on a national scale. Different factors of importance or of possible importance for the long-term radiological safety, technology, land and environment as well as society are described and evaluated. This report is the overall description on general siting studies which the government considered that SKB should report in connection with the RD and D Programme 95. 121 refs, 40 figs.

Site scientific mission plan for the Southern Great Plains CART site: July--December 1997

Energy Technology Data Exchange (ETDEWEB)

Peppler, R.A.; Lamb, P.J. [Univ. of Oklahoma, Norman, OK (United States). Cooperative Inst. for Mesoscale Meteorological Studies; Sisterson, D.L. [Argonne National Lab., IL (United States). Environmental Research Div.

1997-07-01

The Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site is designed to help satisfy the data needs of the Atmospheric Radiation Measurement (ARM) Program Science Team. This document defines the scientific priorities for site activities during the six months beginning on July 1, 1997, and looks forward in lesser detail to subsequent six-month periods. The primary purpose of this Site Scientific Mission Plan is to provide guidance for the development of plans for site operations. It also provides information on current plans to the ARM functional teams and serves to disseminate the plans more generally within the ARM Program and among the members of the Science Team. This document includes a description of the operational status of the site and the primary site activities envisioned, together with information concerning approved and proposed intensive observation periods (IOPs). This plan is a living document that is updated and reissued every six months as the observational facilities are developed, tested, and augmented and as priorities are adjusted in response to developments in scientific planning and understanding.

Geostatistical characterisation of geothermal parameters for a thermal aquifer storage site in Germany

Science.gov (United States)

Rodrigo-Ilarri, J.; Li, T.; Grathwohl, P.; Blum, P.; Bayer, P.

2009-04-01

The design of geothermal systems such as aquifer thermal energy storage systems (ATES) must account for a comprehensive characterisation of all relevant parameters considered for the numerical design model. Hydraulic and thermal conductivities are the most relevant parameters and its distribution determines not only the technical design but also the economic viability of such systems. Hence, the knowledge of the spatial distribution of these parameters is essential for a successful design and operation of such systems. This work shows the first results obtained when applying geostatistical techniques to the characterisation of the Esseling Site in Germany. In this site a long-term thermal tracer test (> 1 year) was performed. On this open system the spatial temperature distribution inside the aquifer was observed over time in order to obtain as much information as possible that yield to a detailed characterisation both of the hydraulic and thermal relevant parameters. This poster shows the preliminary results obtained for the Esseling Site. It has been observed that the common homogeneous approach is not sufficient to explain the observations obtained from the TRT and that parameter heterogeneity must be taken into account.

Site scientific mission plan for the Southern Great Plains CART Site, January--June 1999

Energy Technology Data Exchange (ETDEWEB)

Peppler, R.A.; Sisterson, D.L.; Lamb, P.

1999-03-10

The Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site was designed to help satisfy the data needs of the Atmospheric Radiation Measurement (ARM) Program Science Team. This Site Scientific Mission Plan defines the scientific priorities for site activities during the six months beginning on January 1, 1999, and looks forward in lesser detail to subsequent six-month periods. The primary purpose of this document is to provide scientific guidance for the development of plans for site operations. It also provides information on current plans to the ARM functional teams (Management Team, Data and Science Integration Team [DSIT], Operations Team, and Instrument Team [IT]) and serves to disseminate the plans more generally within the ARM Program and among the members of the Science Team. This document includes a description of the operational status of the site and the primary site activities envisioned, together with information concerning approved and proposed intensive observation periods (IOPs). The primary users of this document are the site operator, the site program manager, the Site Scientist Team (SST), the Science Team through the ARM Program science director, the ARM Program Experiment Center, and the aforementioned ARM Program functional teams. This plan is a living document that is updated and reissued every six months as the observational facilities are developed, tested, and augmented and as priorities are adjusted in response to developments in scientific planning and understanding.

Site scientific mission plan for the Southern Great Plains CART site: July--December 1998

Energy Technology Data Exchange (ETDEWEB)

Peppler, R.A.; Lamb, P. [Univ. of Oklahoma, Norman, OK (United States). Cooperative Inst. for Mesoscale Meteorological Studies; Sisterson, D.L. [Argonne National Lab., IL (United States). Environmental Research Div.

1998-07-01

The Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site was designed to help satisfy the data needs of the Atmospheric Radiation Measurement (ARM) Program Science Team. This Site Scientific Mission Plan defines the scientific priorities for site activities during the six months beginning on July 1, 1998, and looks forward in lesser detail to subsequent six-month periods. The primary purpose of this document is to provide scientific guidance for the development of plans for site operations. It also provides information on current plans to the ARM functional teams (Management Team, Data and Science Integration Team [DSIT], Operations Team, and Instrument Team [IT]) and serves to disseminate the plans more generally within the ARM Program and among the members of the Science Team. This document includes a description of the operational status of the site and the primary site activities envisioned, together with information concerning approved and proposed intensive observation periods (IOPs). The primary users of this document are the site operator, the site program manager, the Site Scientist Team (SST), the Science Team through the ARM Program science director, the ARM program Experiment Center, and the aforementioned ARM Program functional teams. This plan is a living document that is updated and reissued every six months as the observational facilities are developed, tested, and augmented and as priorities are adjusted in response to developments in scientific planning and understanding.

Examining social work with children and youth in welfare service organizations observed as hybrids

DEFF Research Database (Denmark)

Montes de Oca, Lis Klovning Hansen

This paper seeks to explore social work as it can be observed in the welfare service organizations of Danish municipalities, specifically within the context of social work concerned with the protection of the child at risk. The paper uses the systems theory of Niklas Luh-mann to elaborate...... within the welfare system of child protection can be said to emerge into a different form than (maybe) other welfare services. The explorative curiosity rises from recognition of the economic systems expansion and dominant semantics within social services, specifically child protection and how social...... workers may and may not refer to this as potential conflict using semantics of conflict. Welfare technologies as for instance the law stipulated “child conversation”, budget control and action plans form the preliminary basis of the decision-making process of a social intervention regarding a child...

Inter- and intra- observer reliability of risk assessment of repetitive work without an explicit method.

Science.gov (United States)

Eliasson, Kristina; Palm, Peter; Nyman, Teresia; Forsman, Mikael

2017-07-01

A common way to conduct practical risk assessments is to observe a job and report the observed long term risks for musculoskeletal disorders. The aim of this study was to evaluate the inter- and intra-observer reliability of ergonomists' risk assessments without the support of an explicit risk assessment method. Twenty-one experienced ergonomists assessed the risk level (low, moderate, high risk) of eight upper body regions, as well as the global risk of 10 video recorded work tasks. Intra-observer reliability was assessed by having nine of the ergonomists repeat the procedure at least three weeks after the first assessment. The ergonomists made their risk assessment based on his/her experience and knowledge. The statistical parameters of reliability included agreement in %, kappa, linearly weighted kappa, intraclass correlation and Kendall's coefficient of concordance. The average inter-observer agreement of the global risk was 53% and the corresponding weighted kappa (K w ) was 0.32, indicating fair reliability. The intra-observer agreement was 61% and 0.41 (K w ). This study indicates that risk assessments of the upper body, without the use of an explicit observational method, have non-acceptable reliability. It is therefore recommended to use systematic risk assessment methods to a higher degree. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Applications of the observational method in deep foundations

Directory of Open Access Journals (Sweden)

Fathi M. Abdrabbo

2012-12-01

Full Text Available The observational method was introduced into geotechnical engineering to improve both theories and construction techniques. This method was developed to avoid highly conservative assumptions about soil properties in geotechnical design when faced with unavoidable uncertainties of natural ground conditions. The assumptions involved in soil mechanics theories usually differ to a certain extent from reality. These assumptions can be improved by employing an observational database. Thus, theories of geotechnical engineering can be developed by observations during the construction stage. Moreover, precise management of construction work by close observations is essential to avoid risk and to alter the design if needed to match the real conditions. This paper sheds some light on the importance of the observational concept in deep foundations through three case studies. The first one demonstrates the effect of working hypotheses on design outputs of an open caisson of 22 m internal diameter. The other two case studies present the difference between theory and reality during construction stage of auger cast-in-place piles (ACIP in difficult subsoil conditions. Importance of merging the documented theories with the available observations is discussed. The study shows that working hypotheses and engineering models affect the cost and the time required for construction of deep foundations. Field observations are essential during installation of ACIP at a site. Some precautions should be considered when drilling ACIP through sandstone of inclined top surface. These precautions are mainly dependent upon field observations during construction. ACIP can be used effectively in soil formations that have galleries and caves using a cement–bentonite mixture to fill the holes of the unsuccessful piles. Finally, the paper shares a series of practical guidelines with engineering community all over the world that may assist in design and construction of deep

Work plan, health and safety plan, and site characterization for the Rust Spoil Area (D-106)

International Nuclear Information System (INIS)

Bohrman, D.E.; Uziel, M.S.; Landguth, D.C.; Hawthorne, S.W.

1990-06-01

As part of the Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) of the Department of Energy's Y-12 Plant located in Oak Ridge, Tennessee, this work plan has been developed for the Rust Spoil Area (a solid waste disposal area). The work plan was developed by the Measurement Applications and Development Group (MAD) of the Health and Safety Research Division (HASRD) at Oak Ridge National Laboratory (ORNL) and will be implemented jointly by ORNL/MAD and the Y-12 Environmental Surveillance Section. This plan consists of four major sections: (1) a project description giving the scope and objectives of the investigation at the Rust Spoil Area; (2) field and sampling procedures describing sample documentation, soil sampling techniques, sample packaging and preservation, equipment decontamination, and disposal of investigation generated wastes; (3) sample analysis procedures detailing necessary analytical laboratory procedures to ensure the quality of chemical results from sample receipt through analysis and data reporting; and (4) a health and safety plan which describes general site hazards and particular hazards associated with specific tasks, assigns responsibilities, establishes personnel protection standards and mandatory safety procedures, and provides emergency information for contingencies that may arise during the course of field operations

Observation systems with alarm thresholds and their use in designing underground facilities

Energy Technology Data Exchange (ETDEWEB)

Olsson, Lars [Geostatistik AB, Tumba (Sweden); Stille, Haakan [Royal Inst. of Tech., Stockholm (Sweden). Div. of Soil and Rock Mechanics

2002-08-01

The decision-based methodology described has wide applications in the building process. It can be applied whenever the exact outcome of the work is not known and where countermeasures might be needed. One such application is in the pre-investigations for the siting of spent nuclear fuel facilities aimed at determining the criteria for abandoning work on a given site. It can be seen that the principles of for designing an observation system and determining the alarm threshold are well understood. Several possible theoretical tools are also known, albeit from other disciplines than civil engineering. However, the choice of tools for a real problem should be investigated so that the advantages and drawbacks are illustrated. Reliable methods for designing observation systems in practice are, however, not known and are therefore not in use. A continuation of this study should therefore be aimed at comparing different theoretical tools and examining their practical application, including Quality Assurance and updating. It is therefore suggested that an observation system with alarm thresholds etc should be designed using the principles described in this report and should include testing and comparison of different models for predicting behaviour. This work could be undertaken for a real or for a hypothetical project. A real project is, of course, more difficult but has all the real-world problems that must be solved. A very brief, and not theoretically fully developed, account of the application of an observation system during the expansion of the interim spent fuel storage facility CLAB is enclosed as Appendix 1. Some comments on proposed changes in the system based on the principles set forth in this report are given in Appendix 2.

Observation systems with alarm thresholds and their use in designing underground facilities

International Nuclear Information System (INIS)

Olsson, Lars; Stille, Haakan

2002-08-01

The decision-based methodology described has wide applications in the building process. It can be applied whenever the exact outcome of the work is not known and where countermeasures might be needed. One such application is in the pre-investigations for the siting of spent nuclear fuel facilities aimed at determining the criteria for abandoning work on a given site. It can be seen that the principles of for designing an observation system and determining the alarm threshold are well understood. Several possible theoretical tools are also known, albeit from other disciplines than civil engineering. However, the choice of tools for a real problem should be investigated so that the advantages and drawbacks are illustrated. Reliable methods for designing observation systems in practice are, however, not known and are therefore not in use. A continuation of this study should therefore be aimed at comparing different theoretical tools and examining their practical application, including Quality Assurance and updating. It is therefore suggested that an observation system with alarm thresholds etc should be designed using the principles described in this report and should include testing and comparison of different models for predicting behaviour. This work could be undertaken for a real or for a hypothetical project. A real project is, of course, more difficult but has all the real-world problems that must be solved. A very brief, and not theoretically fully developed, account of the application of an observation system during the expansion of the interim spent fuel storage facility CLAB is enclosed as Appendix 1. Some comments on proposed changes in the system based on the principles set forth in this report are given in Appendix 2

Traffic restrictions: Meyrin site and entrance of Prévessin site

CERN Multimedia

GS Department

2010-01-01

Between 10 April and 19 April 2010 a number of roads on the Meyrin site and at the entrance of the Prévessin site will be resurfaced. The work will be done by zones, as shown below: 12-14 April Intersection of Route Fermi and Route Gregory. Route Fermi, between Building 268 and Route Jentschke Route Fermi, Route Jentschke and Route Einstein, up to Building 593 and between Buildings 194 and 555. Plus Route Oppenheimer. 15 April Intersection of Route Bloch and Route Maxwell, and Route Maxwell itself. Route Sherrer between the overhead walkway (Building 50) and the exit from the carpark behind Building 4. 16 April and 19 April Route Fermi, Route Jentschke and Route Einstein, up to Building 593 and between Buildings 194 and 555. Prévessin site: from Route Adams to the access control Building. The construction works may result in some disruption to traffic. Users are requested to comply with the temporary traffic signs and arrangements.  Thank you for your understanding. GS/...

Underwater and Dive Station Work-Site Noise Surveys

National Research Council Canada - National Science Library

Wolgemuth, Keith S; Cudahy, Edward A; Schwaller, Derek W

2008-01-01

...) data This study extends this previous work by obtaining in-water and in-air noise measurements and a total noise dose for Navy divers during actual diving operations using a portable sound level...

Storage of radioactive wastes in geological formations. Technical criteria for site selection. Report by the work-group chaired by Professor Goguel

International Nuclear Information System (INIS)

Goguel, Jean; Candes, Pierre; Izabel, Cecile; Autran, Albert; Barthoux, Alain; Baudin, Guy; Devillers, Christian; Habib, Pierre; Lafuma, Jacques; Lefevre, Jean; Peaudecerf, Pierre; Pradel, Jacques; Salle, Claude; Treuil, Michel; Lebrun, Patrick; Tissier, Marie-Solange

1985-06-01

This document is the result of a prospective mission on the long term storage of radioactive wastes containing long-period emitters (wastes of B and C categories), and notably on a definitive storage in deep continental geological formations. After a presentation of hypotheses (brief description of the storage concept, main safety principles, objectives in terms of radiological safety, safety options, time-related considerations), the authors addressed the following issues: safety before closing during the exploitation period, and safety after closure (after backfilling and sealing of all underground cavities). For the first issue, they discuss the impacts of works on safety and thermal effects during exploitation. For the second issue, they discuss the site natural hydro-geological context, the disturbances brought by the storage (access of water to the storage, and return of water into the biosphere), and the influence of external factors (geological phenomena, human intrusion). Then, the authors make recommendations regarding reconnaissance programs and studies for the selection and qualification of a site. They finally propose technical criteria and main recommendations for site selection. Appendices propose a list of hearings, a presentation of the storage concept, a report on the impact of works, a report on the presence of mineralisation in granite massifs, reports on radiological consequences of intrusions in salt formations and in granite massif containing storage of radioactive wastes or vitrified wastes, a report on the characterization of unsteady parts of the French continental construction, a presentation of the evolution of climate and icings, and a study of seismic movements in the case of deep storages

I Assumed You Knew: Teaching Assumptions as Co-Equal to Observations in Scientific Work

Science.gov (United States)

Horodyskyj, L.; Mead, C.; Anbar, A. D.

2016-12-01

Introductory science curricula typically begin with a lesson on the "nature of science". Usually this lesson is short, built with the assumption that students have picked up this information elsewhere and only a short review is necessary. However, when asked about the nature of science in our classes, student definitions were often confused, contradictory, or incomplete. A cursory review of how the nature of science is defined in a number of textbooks is similarly inconsistent and excessively loquacious. With such confusion both from the student and teacher perspective, it is no surprise that students walk away with significant misconceptions about the scientific endeavor, which they carry with them into public life. These misconceptions subsequently result in poor public policy and personal decisions on issues with scientific underpinnings. We will present a new way of teaching the nature of science at the introductory level that better represents what we actually do as scientists. Nature of science lessons often emphasize the importance of observations in scientific work. However, they rarely mention and often hide the importance of assumptions in interpreting those observations. Assumptions are co-equal to observations in building models, which are observation-assumption networks that can be used to make predictions about future observations. The confidence we place in these models depends on whether they are assumption-dominated (hypothesis) or observation-dominated (theory). By presenting and teaching science in this manner, we feel that students will better comprehend the scientific endeavor, since making observations and assumptions and building mental models is a natural human behavior. We will present a model for a science lab activity that can be taught using this approach.

The viking landing sites: selection and certification.

Science.gov (United States)

Masursky, H; Crabill, N L

1976-08-27

During the past several years the Viking project developed plans to use Viking orbiter instruments and Earth-based radar to certify the suitability of the landing sites selected as the safest and most scientifically rewarding using Mariner 9 data. During June and July 1976, the Earth-based radar and orbital spacecraft observations of some of the prime and backup sites were completed. The results of these combined observations indicated that the Viking 1 prime landing area in the Chryse region of Mars is geologically varied and possibly more hazardous than expected, and was not certifiable as a site for the Viking 1 landing. Consequently, the site certification effort had to be drastically modified and lengthened to search for a site that might be safe enough to attempt to land. The selected site considered at 47.5 degrees W, 22.4 degrees N represented a compromise between desirable characteristics observed with visual images and those inferred from Earth-based radar. It lies in the Chryse region about 900 kilometers northwest of the original site. Viking 1 landed successfully at this site on 20 July 1976.

Origin and variability in volatile organic compounds observed at an Eastern Mediterranean background site (Cyprus)

Science.gov (United States)

Debevec, Cécile; Sauvage, Stéphane; Gros, Valérie; Sciare, Jean; Pikridas, Michael; Stavroulas, Iasonas; Salameh, Thérèse; Leonardis, Thierry; Gaudion, Vincent; Depelchin, Laurence; Fronval, Isabelle; Sarda-Esteve, Roland; Baisnée, Dominique; Bonsang, Bernard; Savvides, Chrysanthos; Vrekoussis, Mihalis; Locoge, Nadine

2017-09-01

or from more distant emission zones (i.e., the south coast of Turkey); and a last factor (36 %) associated with regional background pollution (air masses transported both from the Western and Eastern Mediterranean regions). One of the two biogenic and the regional background factors were found to be the largest contributors to the VOC concentrations observed at our sampling site. Finally, a combined analysis of VOC PMF factors with source-apportioned organic aerosols (OAs) helped to better distinguish between anthropogenic and biogenic influences on the aerosol and gas phase compositions. The highest OA concentrations were observed when the site was influenced by air masses rich in semi-volatile OA (less oxidized aerosols) originating from the southwest of Asia, in contrast with OA factor contributions associated with the remaining source regions. A reinforcement of secondary OA formation also occurred due to the intense oxidation of biogenic precursors.

Origin and variability in volatile organic compounds observed at an Eastern Mediterranean background site (Cyprus

Directory of Open Access Journals (Sweden)

C. Debevec

2017-09-01

as being either of local origin or from more distant emission zones (i.e., the south coast of Turkey; and a last factor (36 % associated with regional background pollution (air masses transported both from the Western and Eastern Mediterranean regions. One of the two biogenic and the regional background factors were found to be the largest contributors to the VOC concentrations observed at our sampling site. Finally, a combined analysis of VOC PMF factors with source-apportioned organic aerosols (OAs helped to better distinguish between anthropogenic and biogenic influences on the aerosol and gas phase compositions. The highest OA concentrations were observed when the site was influenced by air masses rich in semi-volatile OA (less oxidized aerosols originating from the southwest of Asia, in contrast with OA factor contributions associated with the remaining source regions. A reinforcement of secondary OA formation also occurred due to the intense oxidation of biogenic precursors.

Confidence assessment. Site descriptive modelling SDM-Site Forsmark

International Nuclear Information System (INIS)

2008-09-01

-existing deformations in the core exceeded the elasticity limit of the intact rock. These problems are identified and considered in the modelling, and affect uncertainty, but have a limited negative impact on confidence. Overall there is limited measurement bias in the data and bias due to poor representativity is much reduced compared with earlier model versions. However, some degree of bias due to limited representativity remains in some areas. An important remaining bias relates to the fracture size data, since these have to be based on outcrops and not on data from the underground. However, the impact on uncertainty can be estimated and is accounted for in the modelling. Many of the alternative hypotheses formed in earlier iterations of the site descriptive modelling work have now been discarded or are handled by bounding assumptions. Nevertheless a few alternative hypotheses needed to be developed into alternative models, to be propagated to safety assessment or engineering. These alternative models concern: fracture size and intensity modelling in the geological DFN; geometry, connectivity and transmissivity of deformation zones in the regional domain; hydraulic properties and connectivity of the fracture network of a scale less than the deterministic deformation zone; alternative hypotheses as to groundwater composition and processes; processes for sulphate reduction; and effects of connectivity, complexity and channelling on distribution of flow. Another prerequisite for confidence is consistency, or at least no conflicts, between the different discipline model interpretations. Furthermore, confidence is enhanced if aspects of the model are supported by independent evidence from different disciplines. Essentially all identified interactions are considered in the site descriptive modelling work. Only data from underground investigations are judged to have the potential to further significantly reduce uncertainties within the potential repository volume: The range of size

[Analysis of musculoskeletal disorders, work load and working postures among manufacturing workers].

Science.gov (United States)

Yu, Shan-fa; Gu, Gui-zhen; Sun, Shi-yi; Wang, Hai-sheng; Cui, Shou-ming; Yang, Xiao-fa; Yang, Shu-le; He, Li-hua; Wang, Sheng

2011-03-01

To analyze the distribution of the musculoskeletal disorders, work load and working postures in different factories, gender, education levels, age and working years among manufacturing workers. In a cross-sectional study of 5134 manufacturing workers in 12 factories, the morbidities for musculoskeletal disorders in one year period were measured with questionnaires. The morbidities for musculoskeletal disorders in body sites: waist, neck, shoulder, wrist, ankle/feet, knee, hip/buttocks and elbows were 59.7%, 47.9%, 38.1%, 33.7%, 26.9%, 25.4%, 15.2%, and 14.9%, respectively in one year period. There were significant differences of morbidities for musculoskeletal symptoms in body sites of workers among different factories (P manufacturing workers were higher; the gender, education level, age and working years could influenced the morbidities for musculoskeletal disorders.

In search of a representative sample of residential building work.

Science.gov (United States)

Lobb, Brenda; Woods, Gregory R

2012-09-01

Most research investigating injuries in construction work is limited by reliance on work samples unrepresentative of the multiple, variable-cycle tasks involved, resulting in incomplete characterisation of ergonomic exposures. In this case study, a participatory approach was used including hierarchical task analysis and site observations of a typical team of house builders in New Zealand, over several working days, to obtain a representative work sample. The builders' work consisted of 14 goal-defined jobs using varying subsets of 15 task types, each taking from less than 1 s to more than 1 h and performed in a variety of postures. Task type and duration varied within and between participants and days, although all participants spent at least 25% of the time moving from place to place, mostly carrying materials, and more than half the time either reaching up or bending down to work. This research has provided a description of residential building work based on a work sample more nearly representative than those previously published and has demonstrated a simple, low-cost but robust field observation method that can provide a valid basis for further study of hazard exposures. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

How registered nurses, licensed practical nurses and resident aides spend time in nursing homes: An observational study.

Science.gov (United States)

McCloskey, Rose; Donovan, Cindy; Stewart, Connie; Donovan, Alicia

2015-09-01

Calls for improved conditions in nursing homes have pointed to the importance of optimizing the levels and skills of care providers. Understanding the work of care providers will help to determine if staff are being used to their full potential and if opportunities exist for improved efficiencies. To explore the activities of care providers in different nursing homes and to identify if variations exist within and across homes and shifts. A multi-centre cross-sectional observational work flow study was conducted in seven different nursing homes sites in one Canadian province. Data were collected by a research assistant who conducted 368 h of observation. The research assistant collected data by following an identical route in each site and recording observations on staff activities. Findings indicate staff activities vary across roles, sites and shifts. Licensed practical nurses (nursing assistants) have the greatest variation in their role while registered nurses have the least amount of variability. In some sites both registered nurses and licensed practical nurses perform activities that may be safely delegated to others. Care providers spend as much as 53.7% of their time engaged in non-value added activities. There may be opportunities for registered nurses and licensed practical nurses to delegate some of their activities to non-regulated workers. The time care providers spend in non-value activities suggest there may be opportunities to improve efficiencies within the nursing home setting. Copyright © 2015 Elsevier Ltd. All rights reserved.

Possible sites for future nuclear power plants in Israel

Energy Technology Data Exchange (ETDEWEB)

Yaar, Ilan, E-mail: ilany@energy.gov.il [Ministry of National Infrastructure, Energy and Water Resources, Chief Scientist Office, 14 Hartum St., POB 36148, Jerusalem 9136002 (Israel); Walter, Ayelet [Ministry of National Infrastructure, Energy and Water Resources, Chief Scientist Office, 14 Hartum St., POB 36148, Jerusalem 9136002 (Israel); Sanders, Yovav [Sysnet Group, Habarzel St. 32, Tel Aviv 69710 (Israel); Felus, Yaron [Survey of Israel, 1 Lincoln St., POB 14171, Tel-Aviv 61141 (Israel); Calvo, Ran; Hamiel, Yariv [Geological Survey of Israel, 30 Malkhe Israel St., Jerusalem 95501 (Israel)

2016-03-15

A preliminary work aimed at allocating suitable new sites for possible NPPs in Israel is presented. The work is based on Israel's present NPP siting criteria, supported by selected procedure performed by various countries that conducted similar process. The site selection process was conducted in two stages: first, a selection procedure using demographic analysis was conducted; second, a seismological and geological analysis process was performed in the remaining area. From the combined two screening processes results, an overall new area of 569 km{sup 2} was located as a possible area for future construction of NPPs in Israel. Further and more comprehensive work, based on the IAEAs site selection guidelines, has to be performed in the future, in order to verify the preliminary findings presented in this work.

Coincident site lattice-matched InGaN on (111) spinel substrates

International Nuclear Information System (INIS)

Norman, A. G.; Dippo, P. C.; Moutinho, H. R.; Simon, J.; Ptak, A. J.

2012-01-01

Coincident site lattice-matched wurtzite (0001) In 0.31 Ga 0.69 N, emitting in the important green wavelength region, is demonstrated by molecular beam epitaxy on a cubic (111) MgAl 2 O 4 spinel substrate. The coincident site lattice matching condition involves a 30 deg. rotation between the lattice of the InGaN epitaxial layer and the lattice of the spinel. This work describes an alternative approach towards realizing more compositionally homogenous InGaN films with low dislocation density emitting in the ''green gap'' of low efficiency currently observed for semiconductor light emitting diodes (LEDs). This approach could lead to higher efficiency green LEDs presently of great interest for solid-state lighting applications.

Well-construction and hydrogeologic data for observation wells in the vicinity of a low-level radioactive-waste disposal site near Sheffield, Illinois

Science.gov (United States)

Mansue, Lawrence J.; Mills, Patrick C.

1991-01-01

The U.S. Geological Survey conducted hydrogeologic studies at the low-level radioactive-waste disposal site near Sheffield, Illinois, from 1976 through 1987. During that period, 108 observation wells were installed in the vicinity of the disposal site in glacial and post-glacial deposits of Quaternary age and bedrock of Pennsylvanian age. Data in this report include the location of each well, the date each well was drilled, the geologic units penetrated by each well, the physical measurements of each well, the elevations of the top (measuring point) of each well and geologic-unit contacts at each well, and the highest and lowest recorded water levels in each well.

Observation and modeling of ambient nitrous acid (HONO) at a rural site (Wangdu) in the North China Plain in summer 2014

Science.gov (United States)

Liu, Y.; Lu, K.; Li, X.; Dong, H.; Tan, Z.; Wu, Y.; Zeng, L.; Bohn, B.; Broch, S.; Zou, Q.; Fuchs, H.; Hofzumahaus, A.; Holland, F.; Rohrer, F.; Min, K. E.; Brown, S. S.; Wahner, A.; Zhang, Y.

2017-12-01

The photolysis of HONO, was frequently determined to be the major OH primary production channels in the city clusters of China. However, the source of ambient HONO is still a mystery needs to be elucidated. In the framework of an integrated field experiment performed at a rural site in the North China Plain (NCP), HONO was measured by two LOPAP instruments and one CEAS instrument in order to obtain the best quality of the observations and comprehensive parameters that support the exploration of the HONO budget were completely available. In general, the observed HONO concentrations by these three different instruments showed reasonable good agreement as indicated by the high correlation efficiencies while the difference of the regression slopes showed the HONO measured uncertainty is about 15% which is twice about the known uncertainties from each instrument. The diurnal variation of the observed HONO concentrations showed high value (1 -5 ppb) at night and small values (100 - 500 ppt) around noon time which is similar to other reported campaigns. With the assumption of photo stationary state, the missing HONO source is determined experimentally constrained to the observed HONO, jHONO, OH, and NO. Possible HONO formation rates from the chemical reactions as proposed from literatures were calculated in the framework of an observational based box model. It is found that heteorogeneous uptake of NO2 on the ground and the photolysis of nitrate were the major HONO sources for this site when constrained with the recommended kinetc parameters. Uncertainty analysis showed that the uptake coefficient of NO2 and the photolysis frequency of nitrate are the important kinetc factors to be determined in the future studies. In addition, the direct emission of HONO from soil is found to be very important for a few days after fertilization.

Site scientific mission plan for the southern Great Plain CART site July-December 1997.

Energy Technology Data Exchange (ETDEWEB)

Lamb, P.J.; Peppler, R.A.; Sisterson, D.L.

1997-08-28

The Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site is designed to help satisfy the data needs of the Atmospheric Radiation Measurement (ARM) Program Science Team. This document defines the scientific priorities for site activities during the six months beginning on July 1, 1997, and looks forward in lesser detail to subsequent six-month periods. The primary purpose of this Site Scientific Mission Plan is to provide guidance for the development of plans for site operations. It also provides information on current plans to the ARM functional teams (Management Team, Data and Science Integration Team [DSIT], Operations Team, Instrument Team [IT], and Campaign Team) and serves to disseminate the plans more generally within the ARM Program and among the members of the Science Team. This document includes a description of the operational status of the site and the primary site activities envisioned, together with information concerning approved and proposed intensive observation periods (IOPs). The primary users of this document are the site operator, the Site Scientist Team (SST), the Science Team through the ARM Program science director, the ARM Program Experiment Center, and the aforementioned ARM Program functional teams. This plan is a living document that is updated and reissued every six months as the observational facilities are developed, tested, and augmented and as priorities are adjusted in response to developments in scientific planning and understanding.

Nocturnal Boundary-Layer Phenomena Observed at a Complex Site During the Perdigão Experiment

Science.gov (United States)

Bell, T.; Klein, P. M.; Smith, E.; Gebauer, J.; Turner, D. D.

2017-12-01

The Perdigão Field Experiment set out to study atmospheric flows in complex terrain and to collect a high-quality dataset for the validation of meso- and micro-scale models. An Intensive Observation Period (IOP) was conducted from May 1, 2017 through June 15, 2017 where a multitude of instruments were deployed in and around two nearly parallel ridges. The Collaborative Lower Atmospheric Mobile Profiling System (CLAMPS) was deployed and operated in the valley between the ridges. The CLAMPS facility, which was developed as a joint effort between the School of Meteorology at OU and NOAA's National Severe Storms Laboratory (NSSL), takes advantage of a microwave radiometer (MWR), an atmospheric emitted radiance interferometer (AERI), and a scanning doppler Lidar to profile the boundary layer with a high temporal and spatial resolution. Optimized Lidar scanning strategies and joint retrievals for the MWR and ARI data provide detailed information about the wind, turbulence and thermodynamic structure from the surface up to 1000 m AGL on most nights; sometimes the max height is even higher. Over the course of the IOP, CLAMPS observed many different phenomena. During some nights, when stronger background prevailed and was directed perpendicular to the valley, waves were observed at the ridges and in the valley. At the same time, radiational cooling led to drainage flows in the valley, particularly during nights when the mesoscale forcing was weak. At first, CLAMPS profile observations and data collected with radiosondes released at a near-by site are compared to assess the data quality. The radiosonde observations are also being used to document and classify the upper-level flow during the IOP. Additionally, CLAMPS data from a few selected nights will be presented and analyzed in terms of turbulence and its impact on mixing inside and above the valley. June 1-2 represents a good base-state case. Winds at ridge height were generally less than 5ms-1 after 0Z and valley flows

Bedrock hydrogeochemistry Forsmark. Site descriptive modelling SDM-Site Forsmark

Energy Technology Data Exchange (ETDEWEB)

Laaksoharju, Marcus [Geopoint AB, Sollentuna (Sweden); Smellie, John [Conterra AB, Partille (Sweden); Tullborg, Eva-Lena [Terralogica, Graabo (Sweden); Gimeno, Maria [Univ. of Zaragoza, Zaragoza (Spain); Hallbeck, Lotta [Microbial Analytics, Goeteborg (Sweden); Molinero, Jorge [Amphos XXI Consulting S.L., Barcelona (Spain); Waber, Nick [Univ. of Bern, Bern (Switzerland)

2008-12-15

The overall objectives of the hydrogeochemical site description for Forsmark are to establish a detailed understanding of the hydrogeochemical conditions at the site, and to use this understanding to develop models that address the needs identified by the safety assessment groups during the site investigation phase. Issues of concern to safety assessment are radionuclide transport and technical barrier behaviour, both of which are dependent on the chemistry of groundwater and porewater and their evolution with time. The specific aims of the hydrogeochemical work were: To document the hydrogeochemistry at the Forsmark site with focus on the development of conceptual models to describe and visualise the site. To provide relevant parameter values to be used for safety assessment calculations. To provide the hydrogeochemical basis for the modelling work by other teams, in particular hydrogeology. To take account of the feedback from the SR-Can safety assessment work that bears relevance to the hydrogeochemical modelling work. The work has involved the development of descriptive and mathematical models for groundwaters in relation to rock domains, fracture domains and deformation zones. In this report, the groundwaters have been interpreted in relation to their origin, evolution and composition, which require close integration with geological, climatological and hydrogeological information. Past climate changes are one of the major driving forces for long-term hydrogeochemical changes (hundreds to thousands of years) and are, therefore, of fundamental importance for understanding the palaeohydrogeological, palaeohydrogeochemical and present evolution of groundwater in the Fennoscandian crystalline bedrock. In contrast, redox buffer capacity of the bedrock will minimise the effects on changes in alkalinity and redox at repository depths, therefore limiting the variations in pH and Eh significantly, regardless of major changes in groundwater composition. There is

Bedrock hydrogeochemistry Forsmark. Site descriptive modelling SDM-Site Forsmark

International Nuclear Information System (INIS)

Laaksoharju, Marcus; Smellie, John; Tullborg, Eva-Lena; Gimeno, Maria; Hallbeck, Lotta; Molinero, Jorge; Waber, Nick

2008-12-01

The overall objectives of the hydrogeochemical site description for Forsmark are to establish a detailed understanding of the hydrogeochemical conditions at the site, and to use this understanding to develop models that address the needs identified by the safety assessment groups during the site investigation phase. Issues of concern to safety assessment are radionuclide transport and technical barrier behaviour, both of which are dependent on the chemistry of groundwater and porewater and their evolution with time. The specific aims of the hydrogeochemical work were: To document the hydrogeochemistry at the Forsmark site with focus on the development of conceptual models to describe and visualise the site. To provide relevant parameter values to be used for safety assessment calculations. To provide the hydrogeochemical basis for the modelling work by other teams, in particular hydrogeology. To take account of the feedback from the SR-Can safety assessment work that bears relevance to the hydrogeochemical modelling work. The work has involved the development of descriptive and mathematical models for groundwaters in relation to rock domains, fracture domains and deformation zones. In this report, the groundwaters have been interpreted in relation to their origin, evolution and composition, which require close integration with geological, climatological and hydrogeological information. Past climate changes are one of the major driving forces for long-term hydrogeochemical changes (hundreds to thousands of years) and are, therefore, of fundamental importance for understanding the palaeohydrogeological, palaeohydrogeochemical and present evolution of groundwater in the Fennoscandian crystalline bedrock. In contrast, redox buffer capacity of the bedrock will minimise the effects on changes in alkalinity and redox at repository depths, therefore limiting the variations in pH and Eh significantly, regardless of major changes in groundwater composition. There is

Site Scientific Mission Plan for the Southern Great Plains CART site: January--June 1994

Energy Technology Data Exchange (ETDEWEB)

Schneider, J.M.; Lamb, P.J. [Univ. of Oklahoma, Norman, OK (United States). Cooperative Inst. for Mesoscale Meteorological Studies; Sisterson, D.L. [Argonne National Lab., IL (United States). Environmental Research Div.

1993-12-01

The Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site is designed to help satisfy the data needs of the Atmospheric Radiation Measurement (ARM) Program Science Team. This document defines the scientific priorities for site activities during the six months beginning on January 1, 1994, and also looks forward in lesser detail to subsequent six-month periods. The primary purpose of this Site Scientific Mission Plan is to provide guidance for the development of plans for site operations. It also provides information on current plans to the ARM Functional Teams (Management Team, Experiment Support Team, Operations Team, Data Management Team, Instrument Team, and Campaign Team), and it serves to disseminate the plans more generally within the ARM Program and among the Science Team. This document includes a description of the site`s operational status and the primary envisaged site activities, together with information concerning approved and proposed Intensive Observation Periods. Amendments will be prepared and distributed whenever the content changes by more than 30% within a six-month period. The primary users of this document are the site operator, the site scientist, the Science Team through the ARM Program Science Director, the ARM Program Experiment Center, and the aforementioned ARM Program Functional Teams. This plan is a living document that will be updated and reissued every six months as the observational facilities are developed, tested, and augmented and as priorities are adjusted in response to developments in scientific planning and understanding.

The EuroSITES network: Integrating and enhancing fixed-point open ocean observatories around Europe

Science.gov (United States)

Lampitt, Richard S.; Larkin, Kate E.; EuroSITES Consortium

2010-05-01

EuroSITES is a 3 year (2008-2011) EU collaborative project (3.5MEuro) with the objective to integrate and enhance the nine existing open ocean fixed point observatories around Europe (www.eurosites.info). These observatories are primarily composed of full depth moorings and make multidisciplinary in situ observations within the water column as the European contribution to the global array OceanSITES (www.oceansites.org). In the first 18 months, all 9 observatories have been active and integration has been significant through the maintenance and enhancement of observatory hardware. Highlights include the enhancement of observatories with sensors to measure O2, pCO2, chlorophyll, and nitrate in near real-time from the upper 1000 m. In addition, some seafloor missions are also actively supported. These include seafloor platforms currently deployed in the Mediterranean, one for tsunami detection and one to monitor fluid flow related to seismic activity and slope stability. Upcoming seafloor science missions in 2010 include monitoring benthic biological communities and associated biogeochemistry as indicators of climate change in both the Northeast Atlantic and Mediterranean. EuroSITES also promotes the development of innovative sensors and samplers in order to progress capability to measure climate-relevant properties of the ocean. These include further developing current technologies for autonomous long-term monitoring of oxygen consumption in the mesopelagic, pH and mesozooplankton abundance. Many of these science missions are directly related to complementary activities in other European projects such as EPOCA, HYPOX and ESONET. In 2010 a direct collaboration including in situ field work will take place between ESONET and EuroSITES. The demonstration mission MODOO (funded by ESONET) will be implemented in 2010 at the EuroSITES PAP observatory. Field work will include deployment of a seafloor lander system with various sensors which will send data to shore in real

Sedentary work and the risks of colon and rectal cancer by anatomical sub-site in the Canadian census health and environment cohort (CanCHEC).

Science.gov (United States)

Pahwa, Manisha; Harris, M Anne; MacLeod, Jill; Tjepkema, Michael; Peters, Paul A; Demers, Paul A

2017-08-01

Sedentary behaviour is a potential risk factor for colorectal cancer. We examined the association between sedentary work, based on body position, and colorectal cancer risk in Canadians. A working body position category (a. sitting; b. standing and walking; c. sitting, standing, and walking; d. other) was assigned to occupations reported by 1991 Canadian Census respondents based on national occupational counselling guidelines. Adjusted hazard ratios (HRs) and 95% confidence intervals (CI) were estimated for cancers of the colon (overall, proximal, and distal) and rectum in men and women newly diagnosed from 1992 to 2010. Compared to "sitting" jobs, men in occupations with "other" (non-sitting, -standing, or -walking) body positions had a weakly significant reduced colon cancer risk (HR=0.93, 95% CI: 0.89, 0.98) primarily attributed to protection at the distal site (HR=0.90, 95% CI: 0.84, 0.97). Men in "standing and walking" and "sitting, standing, and walking" jobs did not have significantly reduced colon cancer risks. No effects were observed for rectal cancer in men or colon and rectal cancer in women. The two significant findings of this analysis should be followed-up in further investigations with additional information on potential confounders. Null findings for rectal cancer were consistent with other studies. Copyright © 2017 Elsevier Ltd. All rights reserved.

Medical work Assessment in German hospitals: a Real-time Observation study (MAGRO – the study protocol

Directory of Open Access Journals (Sweden)

Mache Stefanie

2009-06-01

Full Text Available Abstract Background The increasing economic pressure characterizes the current situation in health care and the need to justify medical decisions and organizational processes due to limited financial resources is omnipresent. Physicians tend to interpret this development as a decimation of their own medical influence. This becomes even more obvious after a change in hospital ownership i.e. from a public to a private profit oriented organization. In this case each work procedure is revised. To date, most research studies have focused mainly on differences between hospitals of different ownership regarding financial outcomes and quality of care, leaving important organizational issues unexplored. Little attention has been devoted to the effects of hospital ownership on physicians' working routines. The aim of this observational real time study is to deliver exact data about physicians' work at hospitals of different ownership. Methods The consequences of different management types on the organizational structures of the physicians' work situation and on job satisfaction in the ward situation are monitored by objective real time studies and multi-level psycho diagnostic measurements. Discussion This study is unique in its focus. To date no results have been found for computer-based real time studies on work activity in the clinical field in order to objectively evaluate a physician's work-related stress. After a complete documentation of the physicians' work processes the daily work flow can be estimated and systematically optimized. This can stimulate an overall improvement of health care services in Germany.

Global work contexts as sites of discursive sense making

DEFF Research Database (Denmark)

Petersen, Nils Braad

2014-01-01

Global work contexts represent highly complex working environments with simultaneous attachment to several projects and teams (Rosen, Furst & Blackburn, 2007). This complexity increases the for the sense-making capabilities of employees (Weick, 1995). MyPhD project examines this sense-making proc...... of knowledge communication networks in a global organisation. Interviews were fully transscribed analysed using a combination of James Gee’s approach to discourse analysis, and a novel adaptation of Auatin’s speech act theory....

Expedited site characterization. Innovative technology summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

Expedited Site Characterization (ESC) has been developed, demonstrated, and deployed as a new time-saving, cost-effective approach for hazardous waste site investigations. ESC is an alternative approach that effectively shortens the length of the assessment period and may significantly reduce costs at many sites. It is not a specific technology or system but is a methodology for most effectively conducting a site characterization. The principal elements of ESC are: a field investigation conducted by an integrated team of experienced professionals working in the field at the same time, analysis, integration and initial validation of the characterization data as they are obtained in the field, and a dynamic work plan that enables the team to take advantage of new insights from recent data to adjust the work plan in the field. This report covers demonstrations that took place between 1989 and 1996. This paper gives a description of the technology and discusses its performance, applications, cost, regulatory and policy issues, and lessons learned.

Expedited site characterization. Innovative technology summary report

International Nuclear Information System (INIS)

1998-12-01

Expedited Site Characterization (ESC) has been developed, demonstrated, and deployed as a new time-saving, cost-effective approach for hazardous waste site investigations. ESC is an alternative approach that effectively shortens the length of the assessment period and may significantly reduce costs at many sites. It is not a specific technology or system but is a methodology for most effectively conducting a site characterization. The principal elements of ESC are: a field investigation conducted by an integrated team of experienced professionals working in the field at the same time, analysis, integration and initial validation of the characterization data as they are obtained in the field, and a dynamic work plan that enables the team to take advantage of new insights from recent data to adjust the work plan in the field. This report covers demonstrations that took place between 1989 and 1996. This paper gives a description of the technology and discusses its performance, applications, cost, regulatory and policy issues, and lessons learned

Site characterization and site response in Port-au-Prince, Haiti

Science.gov (United States)

Hough, Susan E.; Yong, Alan K.; Altidor, Jean Robert; Anglade, Dieuseul; Given, Douglas D.; Mildor, Saint-Louis

2011-01-01

Waveform analysis of aftershocks of the Mw7.0 Haiti earthquake of 12 January 2010 reveals amplification of ground motions at sites within the Cul de Sac valley in which Port-au-Prince is situated. Relative to ground motions recorded at a hard-rock reference site, peak acceleration values are amplified by a factor of approximately 1.8 at sites on low-lying Mio-Pliocene deposits in central Port-au-Prince and by a factor of approximately 2.5–3 on a steep foothill ridge in the southern Port-au-Prince metropolitan region. The observed amplitude, predominant periods, variability, and polarization of amplification are consistent with predicted topographic amplification by a steep, narrow ridge. A swath of unusually high damage in this region corresponds with the extent of the ridge where high weak-motion amplifications are observed. We use ASTER (Advanced Spaceborne Thermal Emission and Reflection Radiometer) imagery to map local geomorphology, including characterization of both near-surface and of small-scale topographic structures that correspond to zones of inferred amplification.

Mars Aeronomy Observer: Report of the Science Working Team

Science.gov (United States)

Hunten, Donald M.; Slavin, James A.; Brace, Lawrence H.; Deming, Drake; Frank, Louis A.; Grebowsky, Joseph M.; Haberle, Robert M.; Hanson, William B.; Intriligator, Devrie S.; Killeen, Timothy L.;

Preliminary site description Forsmark area - version 1.2

Energy Technology Data Exchange (ETDEWEB)

Skagius, Kristina [ed.

2005-06-01

The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterisation at two different locations, the Forsmark and Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. An integrated component in the characterisation work is the development of a site descriptive model that constitutes a description of the site and its regional setting, covering the current state of the geosphere and the biosphere as well as those ongoing natural processes that affect their long-term evolution. The present report documents the site descriptive modelling activities (version 1.2) for the Forsmark area. The overall objectives of the version 1.2 site descriptive modelling are to produce and document an integrated description of the site and its regional environments based on the site-specific data available from the initial site investigations and to give recommendations on continued investigations. The modelling work is based on primary data, i.e. quality-assured, geoscientific and ecological field data available in the SKB databases SICADA and GIS, available July 31, 2004. The work has been conducted by a project group and associated discipline-specific working groups. The members of the project group represent the disciplines of geology, rock mechanics, thermal properties, hydrogeology, hydrogeochemistry, transport properties and surface ecosystems (including overburden, surface hydrogeochemistry and hydrology). In addition, some group members have specific qualifications of importance in this type of project e.g. expertise in RVS (Rock Visualisation System) modelling, GIS-modelling and in statistical data analysis. The overall strategy to achieve a site description is to develop discipline-specific models by interpretation and analyses of the primary data. The different discipline-specific models are then integrated into a site description. Methodologies for developing the discipline-specific models are documented in

Preliminary site description Forsmark area - version 1.2

International Nuclear Information System (INIS)

Skagius, Kristina

2005-06-01

The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterisation at two different locations, the Forsmark and Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. An integrated component in the characterisation work is the development of a site descriptive model that constitutes a description of the site and its regional setting, covering the current state of the geosphere and the biosphere as well as those ongoing natural processes that affect their long-term evolution. The present report documents the site descriptive modelling activities (version 1.2) for the Forsmark area. The overall objectives of the version 1.2 site descriptive modelling are to produce and document an integrated description of the site and its regional environments based on the site-specific data available from the initial site investigations and to give recommendations on continued investigations. The modelling work is based on primary data, i.e. quality-assured, geoscientific and ecological field data available in the SKB databases SICADA and GIS, available July 31, 2004. The work has been conducted by a project group and associated discipline-specific working groups. The members of the project group represent the disciplines of geology, rock mechanics, thermal properties, hydrogeology, hydrogeochemistry, transport properties and surface ecosystems (including overburden, surface hydrogeochemistry and hydrology). In addition, some group members have specific qualifications of importance in this type of project e.g. expertise in RVS (Rock Visualisation System) modelling, GIS-modelling and in statistical data analysis. The overall strategy to achieve a site description is to develop discipline-specific models by interpretation and analyses of the primary data. The different discipline-specific models are then integrated into a site description. Methodologies for developing the discipline-specific models are documented in

Spatio-temporal evolution of fault networks: implications for deep radioactive waste disposal sites

International Nuclear Information System (INIS)

Hardacre, K.; Scotti, O.

2001-01-01

The objective of this work is to provide estimates of both vertical and lateral propagation rates, on time scales of 100 000 years, for the faults systems known to be present today in the region of Bure, the site of an underground rock laboratory. The project is divided into three parts: 1) literature review (fault growth processes and data), 2) benchmarking against data a numerical code that allows for spontaneous development and growth of faults and 3) application to the Bure site. A brief overview of fault growth processes and observed fault propagation rates shows that non-negligible values (20-50 mm/yrs or roughly 5 km in 100 000 years) can be reached. Preliminary results obtained from two numerical simulations 1) fault growth of a pre-existing weaknesses and 2) fault growth of a spontaneously generated fault system, provide encouraging results with values that are comparable with those observed in nature for the growth of normal fault systems. The application to strike-slip system that characterizes the Bure site is still underway. (authors)

Time series observations of marsh recovery and pavement persistence at three Metula spill sites after 30.5 years

Energy Technology Data Exchange (ETDEWEB)

Owens, E.H. [Polaris Applied Sciences Inc., Bainbridge Island, WA (United States); Sergy, G.A. [Environment Canada, Edmonton, AB (Canada)

2005-07-01

In 1974, the oil tanker Metula ran aground in the Strait of Magellan, Chile and spilled about 50,000 tons of light Arabian crude and 2,000 tons of Bunker C fuel. No attempt was made to recover or treat the stranded oil and the coast was left to recover by natural attenuation. Field visits to the coastal sites affected by the spill were conducted 30 years after the incident. The survey in 2005 repeated observations and measurements made in 1998 in the heavily affected Punta Espora area that documented salt marsh recovery at 2 sites, and changes in asphalt pavement at a third site. The 1998 survey also indicated that tilling was responsible for a significant increase in the number of plants that recolonized the area. A comparison of the plant counts between 1998 and 2005 showed that the number of plants in tilled plots was reduced because of fewer larger plants. A comparison of oil distribution in the west marsh from 1998 to 2005 showed that recolonization was evident. A large 550 m-long asphalt pavement on a mixed sediment beach showed very little changes in pavement area in the aftermath of the spill. However, the upper edge of the pavement showed signs of erosion by backwash action of waves during high-tide. The presence of surface oil cover continues to dominate the physical character of the upper intertidal and supratidal zones. 11 refs., 6 tabs., 3 figs.

Time series observations of marsh recovery and pavement persistence at three Metula spill sites after 30.5 years

International Nuclear Information System (INIS)

Owens, E.H.; Sergy, G.A.

2005-01-01

In 1974, the oil tanker Metula ran aground in the Strait of Magellan, Chile and spilled about 50,000 tons of light Arabian crude and 2,000 tons of Bunker C fuel. No attempt was made to recover or treat the stranded oil and the coast was left to recover by natural attenuation. Field visits to the coastal sites affected by the spill were conducted 30 years after the incident. The survey in 2005 repeated observations and measurements made in 1998 in the heavily affected Punta Espora area that documented salt marsh recovery at 2 sites, and changes in asphalt pavement at a third site. The 1998 survey also indicated that tilling was responsible for a significant increase in the number of plants that recolonized the area. A comparison of the plant counts between 1998 and 2005 showed that the number of plants in tilled plots was reduced because of fewer larger plants. A comparison of oil distribution in the west marsh from 1998 to 2005 showed that recolonization was evident. A large 550 m-long asphalt pavement on a mixed sediment beach showed very little changes in pavement area in the aftermath of the spill. However, the upper edge of the pavement showed signs of erosion by backwash action of waves during high-tide. The presence of surface oil cover continues to dominate the physical character of the upper intertidal and supratidal zones. 11 refs., 6 tabs., 3 figs

Observations of fine particulate nitrated phenols in four sites in northern China: concentrations, source apportionment, and secondary formation

Science.gov (United States)

Wang, Liwei; Wang, Xinfeng; Gu, Rongrong; Wang, Hao; Yao, Lan; Wen, Liang; Zhu, Fanping; Wang, Weihao; Xue, Likun; Yang, Lingxiao; Lu, Keding; Chen, Jianmin; Wang, Tao; Zhang, Yuanghang; Wang, Wenxing

2018-03-01

Filter samples of fine particulate matters were collected at four sites in northern China (urban, rural, and mountain) in summer and winter, and the contents of nine nitrated phenols were quantified in the laboratory with the use of ultra-high-performance liquid chromatography coupled with mass spectrometry. During the sampling periods, the concentrations of particulate nitrated phenols exhibited distinct temporal and spatial variation. On average, the total concentration of particulate nitrated phenols in urban Jinan in the wintertime reached 48.4 ng m-3, and those in the summertime were 9.8, 5.7, 5.9, and 2.5 ng m-3 in urban Jinan, rural Yucheng and Wangdu, and Mt. Tai, respectively. The elevated concentrations of nitrated phenols in wintertime and in urban areas demonstrate the apparent influences of anthropogenic sources. The positive matrix factorization receptor model was then applied to determine the origins of particulate nitrated phenols in northern China. The five major source factors were traffic, coal combustion, biomass burning, secondary formation, and aged coal combustion plume. Among them, coal combustion played a vital role, especially at the urban site in the wintertime, with a contribution of around 55 %. In the summertime, the observed nitrated phenols were highly influenced by aged coal combustion plumes at all of the sampling sites. Meanwhile, in remote areas, contributions from secondary formation were significant. Further correlation analysis indicates that nitrosalicylic acids were produced mostly from secondary formation that was dominated by NO2 nitration.

Innovations in Site Characterization Case Study: The Role of a Conceptual Site Model for Expedited Site Characterization Using the Triad Approach at the Poudre River Site, Fort Collins, Colorado

Science.gov (United States)

This case study examines how systematic planning, an evolving conceptual site model (CSM), dynamic work strategies, and real time measurement technologies can be used to unravel complex contaminant distribution patterns...

Vatwa Resettlement Sites

International Development Research Centre (IDRC) Digital Library (Canada)

The BSUP sites, constructed under the Government of India's .... conflicts over paying for maintenance lead to unrepaired water and ... So some women reacted and broke things in the office." ... workplaces, leading many to drop out of work or.

Site Practice

DEFF Research Database (Denmark)

Wahedi, Haseebullah

2016-01-01

different practices in the construction phase. The research is based on an ethnographic study of a case in Denmark. The empirical data were collected through direct observations and semi-structured interviews with site managers, contract managers, foremen and craftsmen. Findings revealed...... that the construction phase comprises several communities and practices, leading to various uses of the drawings. The results indicated that the craftsmen used drawings to position themselves in the correct location, and that the site managers and contract managers used them as management tools and legal documents...

[Neighborhood Systematic Social Observation; The Case of Chile and its Perspectives for Social Work.

Science.gov (United States)

Sanhueza, Guillermo E; Delva, Jorge; Andrade, Fernando H; Grogan-Kaylor, Andrew; Bares, Cristina; Castillo, Marcela

2011-12-01

The study of neighborhood characteristics and their effects on individuals has become an area of increasing attention by scholars from various disciplines in developed countries. Although there are various methods to study neighborhoods and their impact on human populations, one of the most used is the Systematic Social Observation -Observación Sistemática de Vecindarios (OSV), in Spanish-because it allows the collection of information about various features of the physical, social, environmental and economic characteristics of neighborhoods. The purpose of this article is to (i) briefly present some research on neighborhood effects influential in the U.S., ii) describe how they Systematic Social Observation was designed and implemented in the city of Santiago, Chile, iii) discuss some facilitators and obstacles of the implementation process and, finally iv) list possible contributions and limitations this approach would offer the profession of social work in Chile.

A working group`s conclusion on site specific flow and transport modelling

Energy Technology Data Exchange (ETDEWEB)

Andersson, J. [Golder Associates AB (Sweden); Ahokas, H. [Fintact Oy, Helsinki (Finland); Koskinen, L.; Poteri, A. [VTT Energy, Espoo (Finland); Niemi, A. [Royal Inst. of Technology, Stockholm (Sweden). Hydraulic Engineering; Hautojaervi, A. [Posiva Oy, Helsinki (Finland)

1998-03-01

This document suggests a strategy plan for groundwater flow and transport modelling to be used in the site specific performance assessment analysis of spent nuclear fuel disposal to be used for the site selection planned by the year 2000. Considering suggested general regulations in Finland, as well as suggested regulations in Sweden and the approach taken in recent safety assessment exercises conducted in these countries, it is clear that in such an analysis, in addition to showing that the proposed repository is safe, there exist needs to strengthen the link between field data, groundwater flow modelling and derivation of safety assessment parameters, and needs to assess uncertainty and variability. The suggested strategy plan builds on an evaluation of different approaches to modelling the groundwater flow in crystalline basement rock, the abundance of data collected in the site investigation programme in Finland, and the modelling methodology developed in the programme so far. It is suggested to model the whole system using nested models, where larger scale models provide the boundary conditions for the smaller ones 62 refs.

Data Validation Package, December 2015, Groundwater and Surface Water Sampling at the Monument Valley, Arizona, Processing Site March 2016

Energy Technology Data Exchange (ETDEWEB)

Tyrrell, Evan [Navarro Research and Engineering, Inc., Oak Ridge, NV (United States); Denny, Angelita [USDOE Office of Legacy Management, Washington, DC (United States)

2016-03-23

Fifty-two groundwater samples and one surface water sample were collected at the Monument Valley, Arizona, Processing Site to monitor groundwater contaminants for evaluating the effectiveness of the proposed compliance strategy as specified in the 1999 Final Site Observational Work Plan for the UMTRA Project Site at Monument Valley, Arizona. Sampling and analyses were conducted as specified in the Sampling and Analysis Plan for U.S. Department of Energy Office of Legacy Management Sites (LMS/PRO/S04351, continually updated, http://energy.gov/lm/downloads/sampling-and-analysis-plan-us-department- energy-office-legacy-management-sites). Samples were collected for metals, anions, nitrate + nitrite as N, and ammonia as N analyses at all locations.

Afraid to Start Because the Outcome is Uncertain?: Social Site Characterization as a Tool for Informing Public Engagement Efforts

Science.gov (United States)

Wade, S.; Greenberg, S.

2009-01-01

This paper introduces the concept of social site characterization as a parallel effort to technical site characterization to be used in evaluating and planning carbon dioxides capture and storage (CCS) projects. Social site characterization, much like technical site characterization, relies on a series of iterative investigations into public attitudes towards a CCS project and the factors that will shape those views. This paper also suggests ways it can be used to design approaches for actively engaging stakeholders and communities in the deployment of CCS projects. This work is informed by observing the site selection process for FutureGen and the implementation of research projects under the Regional Carbon Sequestration Partnership Program. ?? 2009 Elsevier Ltd. All rights reserved.

Site Outcomes Baseline Multi Year Work Plan Volume 1, River Corridor Restoration Baseline

International Nuclear Information System (INIS)

Wintczak, T.M.

2001-01-01

The River Corridor Restoration volume is a compilation of Hanford Site scope, which excludes the approximately 194 km 2 Central Plateau. The River Corridor scope is currently contractually assigned to Fluor Hanford, Bechtel Hanford, inc., DynCorp, and Pacific Northwest National Laboratory, and others. The purpose of this project specification is to provide an overall scoping document for the River Corridor Restoration volume, and to provide a link with the overall Hanford Site River Corridor scope. Additionally, this specification provides an integrated and consolidated source of information for the various scopes, by current contract, for the River Corridor Restoration Baseline. It identifies the vision, mission, and goals, as well as the operational history of the Hanford Site, along with environmental setting and hazards

Grid Site Testing for ATLAS with HammerCloud

CERN Document Server

Elmsheuser, J; The ATLAS collaboration; Legger, F; Medrano LLamas, R; Sciacca, G; van der Ster, D

2014-01-01

With the exponential growth of LHC (Large Hadron Collider) data in 2012, distributed computing has become the established way to analyze collider data. The ATLAS grid infrastructure includes more than 130 sites worldwide, ranging from large national computing centers to smaller university clusters. HammerCloud was previously introduced with the goals of enabling VO- and site-administrators to run validation tests of the site and software infrastructure in an automated or on-demand manner. The HammerCloud infrastructure has been constantly improved to support the addition of new test work-flows. These new work-flows comprise e.g. tests of the ATLAS nightly build system, ATLAS MC production system, XRootD federation FAX and new site stress test work-flows. We report on the development, optimization and results of the various components in the HammerCloud framework.

Grid Site Testing for ATLAS with HammerCloud

CERN Document Server

Elmsheuser, J; The ATLAS collaboration; Legger, F; Medrano LLamas, R; Sciacca, G; van der Ster, D

2013-01-01

With the exponential growth of LHC (Large Hadron Collider) data in 2012, distributed computing has become the established way to analyze collider data. The ATLAS grid infrastructure includes more than 130 sites worldwide, ranging from large national computing centers to smaller university clusters. HammerCloud was previously introduced with the goals of enabling VO- and site-administrators to run validation tests of the site and software infrastructure in an automated or on-demand manner. The HammerCloud infrastructure has been constantly improved to support the addition of new test work-flows. These new work-flows comprise e.g. tests of the ATLAS nightly build system, ATLAS MC production system, XRootD federation FAX and new site stress test work-flows. We report on the development, optimization and results of the various components in the HammerCloud framework.

OMI Satellite and Ground-Based Pandora Observations and Their Application to Surface NO2 Estimations at Terrestrial and Marine Sites

Science.gov (United States)

Kollonige, Debra E.; Thompson, Anne M.; Josipovic, Miroslav; Tzortziou, Maria; Beukes, Johan P.; Burger, Roelof; Martins, Douglas K.; van Zyl, Pieter G.; Vakkari, Ville; Laakso, Lauri

2018-01-01

The Pandora spectrometer that uses direct-Sun measurements to derive total column amounts of gases provides an approach for (1) validation of satellite instruments and (2) monitoring of total column (TC) ozone (O3) and nitrogen dioxide (NO2). We use for the first time Pandora and Ozone Monitoring Instrument (OMI) observations to estimate surface NO2 over marine and terrestrial sites downwind of urban pollution and compared with in situ measurements during campaigns in contrasting regions: (1) the South African Highveld (at Welgegund, 26°34'10″S, 26°56'21″E, 1,480 m asl, 120 km southwest of the Johannesburg-Pretoria megacity) and (2) shipboard U.S. mid-Atlantic coast during the 2014 Deposition of Atmospheric Nitrogen to Coastal Ecosystems (DANCE) cruise. In both cases, there were no local NOx sources but intermittent regional pollution influences. For TC NO2, OMI and Pandora difference is 20%, with Pandora higher most times. Surface NO2 values estimated from OMI and Pandora columns are compared to in situ NO2 for both locations. For Welgegund, the planetary boundary layer (PBL) height, used in converting column to surface NO2 value, has been estimated by three methods: co-located Atmospheric Infrared Sounder (AIRS) observations; a model simulation; and radiosonde data from Irene, 150 km northeast of the site. AIRS PBL heights agree within 10% of radiosonde-derived values. Absolute differences between Pandora- and OMI-estimated surface NO2 and the in situ data are better at the terrestrial site ( 0.5 ppbv and 1 ppbv or greater, respectively) than under clean marine air conditions, with differences usually >3 ppbv. Cloud cover and PBL variability influence these estimations.

Searching your site`s management information systems

Energy Technology Data Exchange (ETDEWEB)

Marquez, W.; Rollin, C. [S.M. Stoller Corp., Boulder, CO (United States)

1994-12-31

The Department of Energy`s guidelines for the Baseline Environmental Management Report (BEMR) encourage the use of existing data when compiling information. Specific systems mentioned include the Progress Tracking System, the Mixed-Waste Inventory Report, the Waste Management Information System, DOE 4700.1-related systems, Programmatic Environmental Impact Statement (PEIS) data, and existing Work Breakdown Structures. In addition to these DOE-Headquarters tracking and reporting systems, there are a number of site systems that will be relied upon to produce the BEMR, including: (1) site management control and cost tracking systems; (2) commitment/issues tracking systems; (3) program-specific internal tracking systems; (4) Site material/equipment inventory systems. New requirements have often prompted the creation of new, customized tracking systems. This is a very time and money consuming process. As the BEMR Management Plan emphasizes, an effort should be made to use the information in existing tracking systems. Because of the wealth of information currently available from in-place systems, development of a new tracking system should be a last resort.

Work Begins at School.

Science.gov (United States)

Casto, James E.

2001-01-01

Students at Clay County High School (West Virginia) get real-world work experience through the school's comprehensive School-to-Work program, now in its third year. Given the limited job availability in this poor rural area, the school supplements work-site experiences with school-based business enterprises, student construction projects, and…

Management of construction safety at RR site

International Nuclear Information System (INIS)

Pathak, B.C.; Khatsuriya, J.R.

2016-01-01

Construction industries are one of the most hazardous industries and hence, promotion of safety remains one of the greatest challenges facing construction industry today. According to ILO estimates: Each year at least 60,000 fatal accidents occur on construction sites around the world or one fatal accident every ten minutes. One in six fatal accidents at work occurs on a construction site. In industrialized countries, as many as 25-40 per cent of work related deaths occur on construction sites, even though the sector employs only 6-10 per cent of the workforce. The number of fatalities occurring from construction work in India is also quite disturbing. Though, the fall of person from height and through openings were the major causes for fatal /serious accidents, the risk of fatal accident involving material handling equipment, either during handling or its maintenance is also significantly high due to use of large number of material handling equipments during construction work. (author)

Manual work in cold environments and its impact on selection of materials for protective gloves based on workplace observations.

Science.gov (United States)

Irzmańska, Emilia; Wójcik, Paulina; Adamus-Włodarczyk, Agnieszka

2018-04-01

This article presents a workplace observations on manual work in cold environments and its impact on the selection of materials for protective gloves. The workplace observations was conducted on 107 workers in 7 companies and involved measurements of the temperature of air and objects in the workplaces; in addition the type of surface and shape of the objects was determined. Laboratory tests were also carried out on 11 materials for protective gloves to be used in cold environments. Protective characteristics, including mechanical properties (wear, cut, tear, and puncture resistance), insulation properties (thermal resistance), functional parameters, and hygienic properties (resistance to surface wetting, material stiffness) were evaluated. Appropriate levels of performance and quality, corresponding to the protective and functional properties of the materials, were determined. Based on the results of manual work and laboratory tests, directions for the selection of materials for the construction of protective gloves were formulated with a view to improving work ergonomics. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characterization Report for the 92-Acre Area of the Area 5 Radioactive Waste Management Site, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

Bechtel Nevada; U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office

2006-01-01

The U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office manages two low-level Radioactive Waste Management Sites at the Nevada Test Site. The Area 5 RWMS uses engineered shallow-land burial cells to dispose of packaged waste. This report summarizes characterization and monitoring work pertinent to the 92-Acre Area in the southeast part of the Area 5 Radioactive Waste Management Sites. The decades of characterization and assessment work at the Area 5 RWMS indicate that the access controls, waste operation practices, site design, final cover design, site setting, and arid natural environment contribute to a containment system that meets regulatory requirements and performance objectives for the short- and long-term protection of the environment and public. The available characterization and Performance Assessment information is adequate to support design of the final cover and development of closure plans. No further characterization is warranted to demonstrate regulatory compliance. U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office is proceeding with the development of closure plans for the six closure units of the 92-Acre Area

Characterization Report for the 92-Acre Area of the Area 5 Radioactive Waste Management Site, Nevada Test Site, Nevada

Energy Technology Data Exchange (ETDEWEB)

Bechtel Nevada; U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office

2006-06-01

The U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office manages two low-level Radioactive Waste Management Sites at the Nevada Test Site. The Area 5 RWMS uses engineered shallow-land burial cells to dispose of packaged waste. This report summarizes characterization and monitoring work pertinent to the 92-Acre Area in the southeast part of the Area 5 Radioactive Waste Management Sites. The decades of characterization and assessment work at the Area 5 RWMS indicate that the access controls, waste operation practices, site design, final cover design, site setting, and arid natural environment contribute to a containment system that meets regulatory requirements and performance objectives for the short- and long-term protection of the environment and public. The available characterization and Performance Assessment information is adequate to support design of the final cover and development of closure plans. No further characterization is warranted to demonstrate regulatory compliance. U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office is proceeding with the development of closure plans for the six closure units of the 92-Acre Area.

Compact Solar Spectrometer Column CO2, and CH4 Observations: Performance Evaluation at Multiple North American TCCON Sites

Science.gov (United States)

Parker, H. A.; Hedelius, J.; Viatte, C.; Wunch, D.; Wennberg, P. O.; Chen, J.; Wofsy, S.; Jones, T.; Franklin, J.; Dubey, M. K.; Roehl, C. M.; Podolske, J. R.; Hillyard, P. W.; Iraci, L. T.

2015-12-01

Measurement, reporting and verification (MRV) of anthropogenic emissions and natural sources and sinks of carbon dioxide (CO2) and methane (CH4) are crucial to predict climate change and develop transparent accounting policies to contain climate forcing. Remote sensing technologies are monitoring column averaged dry air mole fractions of CO2 and CH4 (XCO2 & XCH4) from ground and space (OCO-2 and GOSAT) with solar spectroscopy enabling direct MRV. However, current ground based coverage is sparse due to the need for large and expensive high-resolution spectrometers that are part of the Total Column Carbon Observing Network (TCCON, Bruker 125HR). This limits our MRV and satellite validation abilities, both regionally and globally. There are striking monitoring gaps in Asia, South America and Africa where the CO2 emissions are growing and there is a large uncertainty in fluxes from land use change, biomass burning and rainforest vulnerability. To fill this gap we evaluate the precision, accuracy and stability of compact, affordable and easy to use low-resolution spectrometers (Bruker EM27/SUN) by comparing with XCO2 and XCH4 retrieved from much larger high-resolution TCCON instruments. As these instruments will be used in a variety of locations, we evaluate their performance by comparing with 2 previous and 4 current United States TCCON sites in different regions up to 2700 km apart. These sites range from polluted to unpolluted, latitudes of 32 to 46°N, and altitudes of 230 to 2241 masl. Comparisons with some of these sites cover multiple years allowing assessment of the EM27/SUN performance not only in various regions, but also over an extended period of time and with different seasonal influences. Results show that our 2 EM27/SUN instruments capture the diurnal variability of the aforementioned constituents very well, but with offsets from TCCON and long-term variability which may be due in part to the extensive movement these spectrometers were subjected to. These

Effects of urban density on carbon dioxide exchanges: Observations of dense urban, suburban and woodland areas of southern England.

Science.gov (United States)

Ward, H C; Kotthaus, S; Grimmond, C S B; Bjorkegren, A; Wilkinson, M; Morrison, W T J; Evans, J G; Morison, J I L; Iamarino, M

2015-03-01

Anthropogenic and biogenic controls on the surface-atmosphere exchange of CO2 are explored for three different environments. Similarities are seen between suburban and woodland sites during summer, when photosynthesis and respiration determine the diurnal pattern of the CO2 flux. In winter, emissions from human activities dominate urban and suburban fluxes; building emissions increase during cold weather, while traffic is a major component of CO2 emissions all year round. Observed CO2 fluxes reflect diurnal traffic patterns (busy throughout the day (urban); rush-hour peaks (suburban)) and vary between working days and non-working days, except at the woodland site. Suburban vegetation offsets some anthropogenic emissions, but 24-h CO2 fluxes are usually positive even during summer. Observations are compared to estimated emissions from simple models and inventories. Annual CO2 exchanges are significantly different between sites, demonstrating the impacts of increasing urban density (and decreasing vegetation fraction) on the CO2 flux to the atmosphere. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Hanford Site Environmental Management Specification

International Nuclear Information System (INIS)

DAILY, J.L.

2001-01-01

The US Department of Energy, Richland Operations Office (RL) has established a document hierarchy as part of its integrated management system. The Strategic Plan defines the vision, values, missions, strategic goals, high-level outcomes, and the basic strategies in achieving those outcomes. As shown in Figure 1-1, the Site Specification derives requirements from the Strategic Plan and documents the top-level mission technical requirements for the work involved in the RL Hanford Site cleanup and infrastructure activities under the responsibility of the U.S. Department of Energy, Office of Environmental Management (EM). It also provides the basis for all contract technical requirements. Since this is limited to the EM work, neither the Fast Flux Test Facility (FFTF) nor the Pacific Northwest National Laboratory (PNNL) non-EM science activities are included. Figure 1-1 also shows the relationship between this Site Specification and the other Site management and planning documents. Similarly, the documents, orders, and laws referenced in this document represent only the most salient sources of requirements. Current and contractual reference data contain a complete set of source documents

Civil engineering work

International Nuclear Information System (INIS)

Cousyn, Rene; Goubin, Jean.

1977-01-01

Although it does not require a specifically new technicality, the Civil Engineering site of a nuclear power plant is a complex work. Considering as an example the power plant currently in construction at Tricastin, the authors describe the main Civil Engineering work and task organization applied to carry it out [fr

Site scientific mission plan for the southern great plains CART site January-June 2000.; TOPICAL

International Nuclear Information System (INIS)

Peppler, R. A.; Sisterson, D. L.; Lamb, P.

2001-01-01

The Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site was designed to help satisfy the data needs of the Atmospheric Radiation Measurement (ARM) Program Science Team. This Site Scientific Mission Plan defines the scientific priorities for site activities during the six months beginning on January 1, 2000, and looks forward in less detail to subsequent six-month periods. The primary purpose of this document is to provide scientific guidance for the development of plans for site operations. It also provides information on current plans to the ARM functional teams (Management Team, Data and Science Integration Team[DSIT], Operations Team, and Instrument Team[IT]) and serves to disseminate the plans more generally within the ARM Program and among the members of the Science Team. This document includes a description of the operational status of the site and the primary site activities envisioned, together with information concerning approved and proposed intensive observation periods (IOPs). The primary users of this document are the site operator, the site program manager, the Site Scientist Team (SST), the Science Team through the ARM Program science director, the ARM Program Experiment Center, and the aforementioned ARM Program functional teams. This plan is a living document that is updated and reissued every six months as the observational facilities are developed, tested, and augmented and as priorities are adjusted in response to developments in scientific planning and understanding. With this issue, many aspects of earlier Site Scientific Mission Plan reports have been moved to ARM sites on the World Wide Web. This report and all previous reports are available on the SGP CART web site

Site scientific mission plan for the Southern Great Plains CART site: January 1997--June 1997

Energy Technology Data Exchange (ETDEWEB)

Peppler, R.A.; Lamb, P.J. [Univ. of Oklahoma, Norman, OK (United States). Cooperative Institute for Mesoscale Meteorological Studies; Sisterson, D.L. [Argonne National Lab., IL (United States)

1997-01-01

The Southern Great Plains (SGP) Cloud and Radiation Testbed (CART) site is designed to help satisfy the data needs of the Atmospheric Radiation Measurement (ARM) Program Science Team. This document defines the scientific priorities for site activities during the six months beginning on January 1, 1997, and looks forward in lesser detail to subsequent six-month periods. The primary purpose of this Site Scientific Mission Plan is to provide guidance for the development of plans for site operations. It also provides information on current plans to the ARM functional teams (Management Team, Data and Science Integration Team [DSIT], Operations Team, Instrument Team [IT], and Campaign Team) and serves to disseminate the plans more generally within the ARM Program and among the members of the Science Team. This document includes a description of the operational status of the site and the primary site activities envisioned, together with information concerning approved and proposed intensive observation periods (IOPs). The primary users of this document are the site operator, the Site Scientist Team (SST), the Science Team through the ARM Program science director, the ARM Program Experiment Center, and the aforementioned ARM Program functional teams. This plan is a living document that is updated and reissued every six months as the observational facilities are developed, tested, and augmented and as priorities are adjusted in response to developments in scientific planning and understanding.

Seismic surface-wave tomography of waste sites. 1998 annual progress report

International Nuclear Information System (INIS)

Long, T.L.

1998-01-01

'The objective of the Seismic Surface Wave Tomography of Waste Sites is to develop a robust technique for field acquisition and analysis of surface wave data for the interpretation of shallow structures, such as those associated with the burial of wastes. The analysis technique is to be developed and tested on an existing set of seismic data covering the K-901 burial site at the East Tennessee Technology Park. Also, a portable prototype for a field acquisition system will be designed and developed to obtain additional data for analysis and testing of the technique. The portable analysis system will display an image representing the shear-wave velocity structure. The image would be developed in the field from successive data samples. As of May 1998, the author established compatibility with computer programs at Georgia Tech and computed a preliminary singular value decomposition solution for the K-901 data. The analysis included modeling of surface wave dispersion and analysis of velocity structure. The analysis demonstrated that the authors needed additional field data to verify the conclusions and provide independent confirmation of velocity structure. The K-901 site data were obtained with 8 Hz geophones. The frequencies below 8 Hz are strongly attenuated in such recording instruments and are difficult to analyze. In particular, group velocities can have multiple answers for a given frequency. Consequently, without a record of the low-frequency energy, the authors found it difficult to identify the portion of the dispersion curve responsible for the seismogram. In particular, it was difficult to determine if the reverse dispersion observed in the frequencies above 8 Hz was caused by a low velocity layer or caused by observing only the frequencies above the group velocity minimum. In either model, synthetic seismograms can be made to match the observed data for the higher frequencies. The contract for the proposed work was completed in December. The field work was

Siting factors for the Swedish deep repository for spent fuel

International Nuclear Information System (INIS)

Stroem, A.; Ericsson, Lars O.; Svemar, C.; Almen, K.E.; Andersson, Johan

1998-01-01

A project entitled Siting factors and criteria for site evaluation was initiated at the SKB in 1997. The project comprises an important part of the work of siting and site selection that is being pursued within SKB. The purpose of the project is to create a logical structure for the continued siting work, and its results should also be able to be used to assist in evaluating sites. The project will thereby also provide a means - in accordance with the Government's decision regarding Research Programme 95 - to obtain more detailed and quantified siting factors and criteria than those previously presented in the supplement to Research Programme 92. The overall goals of the project are to identify and quantify requirements and preferences regarding the properties of the rock and the soil from the perspectives of long-term safety, performance and planning and design of the rock works, and to identify siting factors and criteria. The latter should be able to be used to determine whether requirements and preferences are satisfied, both when screening sites for site investigation and after completed site investigation. Presented requirements, preferences, factors and criteria must be acceptable to national and municipal authorities or others with influence over the siting work. To start with, requirements and preferences regarding the performance of the rock in a deep repository have been clarified. These requirements and preferences are based on many years of experience of safety assessments and construction analyses within SKB. What is new here is the structuring that has been done, where a classification is made into different geoscientific disciplines, and the formalism that has been developed for the concepts requirements, preferences and performance. This is a prerequisite for a consistent and hopefully comprehensive set of requirements from a functional perspective. Work has continued on siting factors with reference to a coming site investigation programme. A

Lessons learned in the implementation of Integrated Safety Management at DOE Order Compliance Sites vs Necessary and Sufficient Sites

International Nuclear Information System (INIS)

Hill, R.L.

2000-01-01

This paper summarizes the development and implementation of Integrated Safety Management (ISM) at an Order Compliance Site (Savannah River Site) and a Necessary and Sufficient Site (Nevada Test Site). A discussion of each core safety function of ISM is followed by an example from an Order Compliance Site and a Necessary and Sufficient Site. The Savannah River Site was the first DOE site to have a DOE Headquarters-validated and approved ISM System. The NTS is beginning the process of verification and validation. This paper defines successful strategies for integrating Environment, Safety, and Health management into work under various scenarios

Coincident site lattice-matched InGaN on (111) spinel substrates

Energy Technology Data Exchange (ETDEWEB)

Norman, A. G.; Dippo, P. C.; Moutinho, H. R.; Simon, J.; Ptak, A. J. [National Renewable Energy Laboratory, Golden, Colorado 80401 (United States)

2012-04-09

Coincident site lattice-matched wurtzite (0001) In{sub 0.31}Ga{sub 0.69}N, emitting in the important green wavelength region, is demonstrated by molecular beam epitaxy on a cubic (111) MgAl{sub 2}O{sub 4} spinel substrate. The coincident site lattice matching condition involves a 30 deg. rotation between the lattice of the InGaN epitaxial layer and the lattice of the spinel. This work describes an alternative approach towards realizing more compositionally homogenous InGaN films with low dislocation density emitting in the ''green gap'' of low efficiency currently observed for semiconductor light emitting diodes (LEDs). This approach could lead to higher efficiency green LEDs presently of great interest for solid-state lighting applications.

An event-related potential study of working memory in children

Institute of Scientific and Technical Information of China (English)

LIU Rong; GUO Chunyan; JIANG Yang

2006-01-01

To examine the neural mechanisms of working memory in children, event-related potentials (ERPs) were recorded from the 12―13 year-old while they performed a delayed match-to-sample task. The ERP results revealed that new and studied objects both evoked a late positive ERP component peaking around 350 ms during the working memory process. New objects evoke a more positive ERP waveform than the studied objects. The scalp distribution showed that the frontal-central electrode sites were associated with object working memory processes. When tracking new or studied targets among visual distracters, ERPs of targets and distracters revealed differential responses as early as 150 ms. The visual targets evoked larger and more positive ERP responses than the distracters. The typical old-new effect was observed between ERPs of studied and new distracters. However, ERPs of new and studied targets differed at about 250 ms, in which new targets evoked more positive-going and slightly earlier ERP responses. In addition, a P3a component was found for new targets only, and was absent in ERPs of studied targets at frontal and central sites. The present study results reveal the spatial and temporal characteristics of neural mechanisms underlying working memory in children, some of which are distinct from those in adults.

Operating a wide-area high-availability collaborative remote observing system for classically-scheduled observations at the W. M. Keck Observatory

Science.gov (United States)

Kibrick, Robert I.; Wirth, Gregory D.; Allen, Steven L.; Deich, William T. S.; Goodrich, Robert W.; Lanclos, Kyle; Lyke, James E.

2011-03-01

For over a decade, the W. M. Keck Observatory's two 10-meter telescopes have been operated remotely from its Waimea headquarters. Over the last 9 years, WMKO remote observing has expanded to allow observing teams at dedicated sites located across California to observe via the Internet either in collaboration with colleagues in Waimea or entirely from California; this capability was extended to Swinburne University in Melbourne, Australia in 2010 and to Yale University in New Haven, Connecticut in early 2011. All Keck facility science instruments are currently supported. Observers distributed between as many as four sites can collaborate in the interactive operation of each instrument by means of shared VNC desktops and multipoint video and/or telephone conferencing. Automated routers at primary remote observing sites ensure continued connectivity during Internet outages. Each Keck remote observing facility is similarly equipped and configured so observers have the same operating environment. This architecture provides observers the flexibility to conduct observations from the location best suited to their needs and to adapt to last-minute changes. It also enhances the ability of off-site technical staff to provide remote support.

Formerly utilized MED/AEC sites remedial action program. Radiological survey of the former Watertown arsenal property, Site 34 and Site 41, Watertown, Massachusetts

International Nuclear Information System (INIS)

Wynveen, R.A.; Smith, W.H.; Sholeen, C.M.; Justus, A.L.; Flynn, K.F.

1983-10-01

During the MED/AEC era, work involving radioactive materials was conducted at various sites within the arsenal complex. Building 34 housed a uranium machine shop, and a portion of Building 41 contained a foundry that was used for uranium work. Information provided by site personnel indicated that only depleted uranium was used in these buildings. Results of radiological analyses of contaminated material found at these sites indicated depleted uranium with uranium-236. Both buildings have been razed. The remnants still in place consist of the concrete floor slabs, access drives, and underground utility service trenches. This area is currently under the control of the Watertown Redevelopment Authority of Watertown, Massachusetts. During the period from June 25 through July 1, 1981, the Argonne National Laboratory (ANL), Occupational Health and Safety Division (OHS) Radiological Survey Group (RSG), conducted a radiological survey of Building Sites 34 and 41 at the direction of the US Department of Energy. Significant levels of contamination were found at 33 locations on the pad of Site 34 and in 5 out of 15 soild corings from the perimeter of the pad. No contamination was found on the pad of Site 41; however, two-thirds of this pad was covered with soil up to 4 ft thick. One of the 14 soil corings taken adjacent to the pad of Site 41 had elevated levels of uranium. Levels of contamination in excess of criteria, as identified in ANSI 13.12 and NRC Guidelines, were found at this site. The analyses of the samples from the sewer access points also revealed uranium and radium-226 anomalies. Therefore, according to NRC guidelines dated July 1982, it must be concluded that they are contaminated

The commissioning of CMS sites: Improving the site reliability

International Nuclear Information System (INIS)

Belforte, S; Fisk, I; Flix, J; Hernandez, J M; Klem, J; Letts, J; Magini, N; Saiz, P; Sciaba, A

2010-01-01

The computing system of the CMS experiment works using distributed resources from more than 60 computing centres worldwide. These centres, located in Europe, America and Asia are interconnected by the Worldwide LHC Computing Grid. The operation of the system requires a stable and reliable behaviour of the underlying infrastructure. CMS has established a procedure to extensively test all relevant aspects of a Grid site, such as the ability to efficiently use their network to transfer data, the functionality of all the site services relevant for CMS and the capability to sustain the various CMS computing workflows at the required scale. This contribution describes in detail the procedure to rate CMS sites depending on their performance, including the complete automation of the program, the description of monitoring tools, and its impact in improving the overall reliability of the Grid from the point of view of the CMS computing system.

Estimating and forecasting the precipitable water vapor from GOES satellite data at high altitude sites

Science.gov (United States)

Marín, Julio C.; Pozo, Diana; Curé, Michel

2015-01-01

In this work, we describe a method to estimate the precipitable water vapor (PWV) from Geostationary Observational Environmental Satellite (GOES) data at high altitude sites. The method was applied at Atacama Pathfinder Experiment (APEX) and Cerro Toco sites, located above 5000 m altitude in the Chajnantor plateau, in the north of Chile. It was validated using GOES-12 satellite data over the range 0-1.2 mm since submillimeter/millimeter astronomical observations are only useful within this PWV range. The PWV estimated from GOES and the Final Analyses (FNL) at APEX for 2007 and 2009 show root mean square error values of 0.23 mm and 0.36 mm over the ranges 0-0.4 mm and 0.4-1.2 mm, respectively. However, absolute relative errors of 51% and 33% were shown over these PWV ranges, respectively. We recommend using high-resolution thermodynamic profiles from the Global Forecast System (GFS) model to estimate the PWV from GOES data since they are available every three hours and at an earlier time than the FNL data. The estimated PWV from GOES/GFS agrees better with the observed PWV at both sites during night time. The largest errors are shown during daytime. Short-term PWV forecasts were implemented at both sites, applying a simple persistence method to the PWV estimated from GOES/GFS. The 12 h and 24 h PWV forecasts evaluated from August to October 2009 indicates that 25% of them show a very good agreement with observations whereas 50% of them show reasonably good agreement with observations. Transmission uncertainties calculated for PWV estimations and forecasts over the studied sites are larger over the range 0-0.4 mm than over the range 0.4-1.2 mm. Thus, the method can be used over the latter interval with more confidence.

Observations of fine particulate nitrated phenols in four sites in northern China: concentrations, source apportionment, and secondary formation

Directory of Open Access Journals (Sweden)

L. Wang

2018-03-01

Full Text Available Filter samples of fine particulate matters were collected at four sites in northern China (urban, rural, and mountain in summer and winter, and the contents of nine nitrated phenols were quantified in the laboratory with the use of ultra-high-performance liquid chromatography coupled with mass spectrometry. During the sampling periods, the concentrations of particulate nitrated phenols exhibited distinct temporal and spatial variation. On average, the total concentration of particulate nitrated phenols in urban Jinan in the wintertime reached 48.4 ng m−3, and those in the summertime were 9.8, 5.7, 5.9, and 2.5 ng m−3 in urban Jinan, rural Yucheng and Wangdu, and Mt. Tai, respectively. The elevated concentrations of nitrated phenols in wintertime and in urban areas demonstrate the apparent influences of anthropogenic sources. The positive matrix factorization receptor model was then applied to determine the origins of particulate nitrated phenols in northern China. The five major source factors were traffic, coal combustion, biomass burning, secondary formation, and aged coal combustion plume. Among them, coal combustion played a vital role, especially at the urban site in the wintertime, with a contribution of around 55 %. In the summertime, the observed nitrated phenols were highly influenced by aged coal combustion plumes at all of the sampling sites. Meanwhile, in remote areas, contributions from secondary formation were significant. Further correlation analysis indicates that nitrosalicylic acids were produced mostly from secondary formation that was dominated by NO2 nitration.

Remediation management of complex sites using an adaptive site management approach.

Science.gov (United States)

Price, John; Spreng, Carl; Hawley, Elisabeth L; Deeb, Rula

2017-12-15

Complex sites require a disproportionate amount of resources for environmental remediation and long timeframes to achieve remediation objectives, due to their complex geologic conditions, hydrogeologic conditions, geochemical conditions, contaminant-related conditions, large scale of contamination, and/or non-technical challenges. A recent team of state and federal environmental regulators, federal agency representatives, industry experts, community stakeholders, and academia worked together as an Interstate Technology & Regulatory Council (ITRC) team to compile resources and create new guidance on the remediation management of complex sites. This article summarizes the ITRC team's recommended process for addressing complex sites through an adaptive site management approach. The team provided guidance for site managers and other stakeholders to evaluate site complexities and determine site remediation potential, i.e., whether an adaptive site management approach is warranted. Adaptive site management was described as a comprehensive, flexible approach to iteratively evaluate and adjust the remedial strategy in response to remedy performance. Key aspects of adaptive site management were described, including tools for revising and updating the conceptual site model (CSM), the importance of setting interim objectives to define short-term milestones on the journey to achieving site objectives, establishing a performance model and metrics to evaluate progress towards meeting interim objectives, and comparing actual with predicted progress during scheduled periodic evaluations, and establishing decision criteria for when and how to adapt/modify/revise the remedial strategy in response to remedy performance. Key findings will be published in an ITRC Technical and Regulatory guidance document in 2017 and free training webinars will be conducted. More information is available at www.itrc-web.org. Copyright © 2017 Elsevier Ltd. All rights reserved.

Coordination and Integration of Global Ocean Observing through JCOMM

Science.gov (United States)

Legler, D. M.; Meldrum, D. T.; Hill, K. L.; Charpentier, E.

2016-02-01

The primary objective of the JCOMM Observations Coordination Group (OCG) is to provide technical coordination to implement fully integrated ocean observing system across the entire marine meteorology and oceanographic community. JCOMM OCG works in partnership with the Global Ocean Observing System, , which focusses on setting observing system requirements and conducting evalutions. JCOMM OCG initially focused on major global observing networks (e.g. Argo profiling floats, moored buoys, ship based observations, sea level stations, reference sites, etc), and is now expanding its horizon in recognition of new observing needs and new technologies/networks (e.g. ocean gliders). Over the next five years the JCOMM OCG is focusing its attention on integration and coordination in four major areas: observing network implementation particularly in response to integrated ocean observing requirements; observing system monitoring and metrics; standards and best practices; and improving integrated data management and access. This presentation will describe the scope and mission of JCOMM OCG; summarize the state of the global ocean observing system; highlight recent successes and resources for the research, prediction, and assessment communities; summarize our plans for the next several years; and suggest engagement opportunities.

Expedited Site Characterization: A rapid, cost-effective process for preremedial site characterization

International Nuclear Information System (INIS)

Burton, J.C.; Walker, J.L.; Jennings, T.V.; Aggarwal, P.K.; Hastings, B.; Meyer, W.T.; Rose, C.M.; Rosignolo, C.L.

1993-01-01

Argonne National Laboratory has developed a unique, cost- and time-effective, technically innovative process for preremedial site characterization, referred to as Expedited Site Characterization (ESC). The cost of the ESC field sampling process ranges from 1/10 to 1/5 of the cost of traditional site characterization. The time required for this ESC field activity is approximately 1/30 of that for current methods. Argonne's preremedial site investigations based on this approach have been accepted by the appropriate regulatory agencies. The ESC process is flexible and neither site nor contaminant dependent. The process has been successfully tested and applied in site investigations of multiple contaminated landfills in New Mexico (for the US Department of the Interior's Bureau of Land Management [BLM]) and at former grain storage facilities in Nebraska and Kansas, contaminated with carbon tetrachloride (for the Department of Agriculture's Commodity Credit Corporation [CCC/USDA]). A working demonstration of this process was sponsored by the US Department of Energy (DOE) Office of Technology Development as a model of the methodology needed to accelerate site characterizations at DOE facilities. This report describes the application of the process in New Mexico, Nebraska and Kansas

Occupational Health Hazards of Women Working in Brick Kiln and Construction Industry

Directory of Open Access Journals (Sweden)

V. G Vaidya

2015-01-01

Full Text Available Background: In brick kiln and construction industry the exposure to carbon monoxide and silica dust is the most common occupational hazard to the workers in these industries. A study on occupational health hazards of working women in these two unorganized sectors was undertaken by Lokmanya Medical Research Centre. Objectives: To study the effect of work site environment on the health of the women working in brick kiln and construction industry. An attempt was also made to study the seasonal changes in the concentration of carbon monoxide and dust at the worksite. Material and Methods: A cross-sectional study was conducted among the working women (age 18-40 years at brick kilns and construction sites during summer and winter season. They were examined primarily to assess the effect of working environment on health. Gasteck Detector Pump of model 800 and air sampling instrument (SKC Air Check–52 were used to measure concentration of carbon monoxide and dust in the air respectively. Results: There were 66% of women who were in the age group of 18-40 years and most of them (94% were married. At brick kiln sites, average CO exposure was 62.8 ppm and 55.5 ppm and average dust exposure was 3 3 146.1 mg/m and 91.4 mg/m in summer and winter season respectively.At construction sites, average dust exposure was 41.5 ppm and 90.8 ppm in summer and winter. Conclusion: Both exposure to CO and dust were more in summer than in winter in brick kiln industry whereas in construction industry the exposure to dust was more in winter season. A high level of morbidity in the form of headache, bodyache, problems with vision, cough and breathlessness were observed in both industries. It is strongly recommended to take pollution control measures.

A mobile robot for precision work in hostile environments