Orthogonal electrode catheter array for mapping of endocardial focal site of ventricular activation

Energy Technology Data Exchange (ETDEWEB)

Desai, J.M.; Nyo, H.; Vera, Z.; Seibert, J.A.; Vogelsang, P.J. (Division of Cardiovascular Medicine, University of California, School of Medicine, Davis (USA))

1991-04-01

Precise location of the endocardial site of origin of ventricular tachycardia may facilitate surgical and catheter ablation of this arrhythmia. The endocardial catheter mapping technique can locate the site of ventricular tachycardia within 4-8 cm2 of the earliest site recorded by the catheter. This report describes an orthogonal electrode catheter array (OECA) for mapping and radiofrequency ablation (RFA) of endocardial focal site of origin of a plunge electrode paced model of ventricular activation in dogs. The OECA is an 8 F five pole catheter with four peripheral electrodes and one central electrode (total surface area 0.8 cm{sup 2}). In eight mongrel dogs, mapping was performed by arbitrarily dividing the left ventricle (LV) into four segments. Each segment was mapped with OECA to find the earliest segment. Bipolar and unipolar electrograms were obtained. The plunge electrode (not visible on fluoroscopy) site was identified by the earliest wave front arrival times of -30 msec or earlier at two or more electrodes (unipolar electrograms) with reference to the earliest recorded surface ECG (I, AVF, and V1). Validation of the proximity of the five electrodes of the OECA to the plunge electrode was performed by digital radiography and RFA. Pathological examination was performed to document the proximity of the OECA to the plunge electrode and also for the width, depth, and microscopic changes of the ablation. To find the segment with the earliest LV activation a total of 10 {plus minus} 3 (mean {plus minus} SD) positions were mapped. Mean arrival times at the two earlier electrodes were -39 {plus minus} 4 msec and -35 {plus minus} 3 msec. Digital radiography showed the plunge electrode to be within the area covered by all five electrodes in all eight dogs. The plunge electrode was within 1 cm2 area of the region of RFA in all eight dogs.

A genome-wide map of hyper-edited RNA reveals numerous new sites

Science.gov (United States)

Porath, Hagit T.; Carmi, Shai; Levanon, Erez Y.

2014-01-01

Adenosine-to-inosine editing is one of the most frequent post-transcriptional modifications, manifested as A-to-G mismatches when comparing RNA sequences with their source DNA. Recently, a number of RNA-seq data sets have been screened for the presence of A-to-G editing, and hundreds of thousands of editing sites identified. Here we show that existing screens missed the majority of sites by ignoring reads with excessive (‘hyper’) editing that do not easily align to the genome. We show that careful alignment and examination of the unmapped reads in RNA-seq studies reveal numerous new sites, usually many more than originally discovered, and in precisely those regions that are most heavily edited. Specifically, we discover 327,096 new editing sites in the heavily studied Illumina Human BodyMap data and more than double the number of detected sites in several published screens. We also identify thousands of new sites in mouse, rat, opossum and fly. Our results establish that hyper-editing events account for the majority of editing sites. PMID:25158696

Geologic mapping as a prerequisite to hazardous waste facility siting

International Nuclear Information System (INIS)

LaMoreaux, P.E.

1993-01-01

The nation's welfare is based on its capability to develop the mineral, water, and energy resources of the land. In addition, these resources must be developed with adequate consideration of environmental impact and the future welfare of the country. Geologic maps are an absolute necessity in the discovery and development of natural resources; for managing radioactive, toxic, and hazardous wastes; and for the assessment of hazards and risks such as those associated with volcanic action, earthquakes, landslides, and subsidence. Geologic maps are the basis for depicting rocks and rock materials, minerals, coal, oil, and water at or near the earth's surface. Hazardous waste facility projects require the preparation of detailed geologic maps. Throughout most of the USA, this type of mapping detail is not available. If these maps were available, it is estimated that the duration of an individual project could be reduced by at least one-fourth (1/4). Therefore, adequate site-specific mapping is required if one is to eliminate environmental problems associated with hazardous, toxic, radioactive, and municipal waste sites

Constraint map for landfill site selection in Akure Metropolis ...

African Journals Online (AJOL)

An integration of remote sensing, soil type, geological, geoelectrical, hydrogeological and geotechnical data was carried out in a GIS environment with a view to developing a constraint map for the location of landfill (waste disposal) site(s) in Akure, Metropolis.. Geomorphological features identified from satellite images ...

A physical map of Brassica oleracea shows complexity of chromosomal changes following recursive paleopolyploidizations

Directory of Open Access Journals (Sweden)

Giattina Emily

2011-09-01

Full Text Available Abstract Background Evolution of the Brassica species has been recursively affected by polyploidy events, and comparison to their relative, Arabidopsis thaliana, provides means to explore their genomic complexity. Results A genome-wide physical map of a rapid-cycling strain of B. oleracea was constructed by integrating high-information-content fingerprinting (HICF of Bacterial Artificial Chromosome (BAC clones with hybridization to sequence-tagged probes. Using 2907 contigs of two or more BACs, we performed several lines of comparative genomic analysis. Interspecific DNA synteny is much better preserved in euchromatin than heterochromatin, showing the qualitative difference in evolution of these respective genomic domains. About 67% of contigs can be aligned to the Arabidopsis genome, with 96.5% corresponding to euchromatic regions, and 3.5% (shown to contain repetitive sequences to pericentromeric regions. Overgo probe hybridization data showed that contigs aligned to Arabidopsis euchromatin contain ~80% of low-copy-number genes, while genes with high copy number are much more frequently associated with pericentromeric regions. We identified 39 interchromosomal breakpoints during the diversification of B. oleracea and Arabidopsis thaliana, a relatively high level of genomic change since their divergence. Comparison of the B. oleracea physical map with Arabidopsis and other available eudicot genomes showed appreciable 'shadowing' produced by more ancient polyploidies, resulting in a web of relatedness among contigs which increased genomic complexity. Conclusions A high-resolution genetically-anchored physical map sheds light on Brassica genome organization and advances positional cloning of specific genes, and may help to validate genome sequence assembly and alignment to chromosomes. All the physical mapping data is freely shared at a WebFPC site (http://lulu.pgml.uga.edu/fpc/WebAGCoL/brassica/WebFPC/; Temporarily password-protected: account

A physical map of Brassica oleracea shows complexity of chromosomal changes following recursive paleopolyploidizations

Science.gov (United States)

2011-01-01

Background Evolution of the Brassica species has been recursively affected by polyploidy events, and comparison to their relative, Arabidopsis thaliana, provides means to explore their genomic complexity. Results A genome-wide physical map of a rapid-cycling strain of B. oleracea was constructed by integrating high-information-content fingerprinting (HICF) of Bacterial Artificial Chromosome (BAC) clones with hybridization to sequence-tagged probes. Using 2907 contigs of two or more BACs, we performed several lines of comparative genomic analysis. Interspecific DNA synteny is much better preserved in euchromatin than heterochromatin, showing the qualitative difference in evolution of these respective genomic domains. About 67% of contigs can be aligned to the Arabidopsis genome, with 96.5% corresponding to euchromatic regions, and 3.5% (shown to contain repetitive sequences) to pericentromeric regions. Overgo probe hybridization data showed that contigs aligned to Arabidopsis euchromatin contain ~80% of low-copy-number genes, while genes with high copy number are much more frequently associated with pericentromeric regions. We identified 39 interchromosomal breakpoints during the diversification of B. oleracea and Arabidopsis thaliana, a relatively high level of genomic change since their divergence. Comparison of the B. oleracea physical map with Arabidopsis and other available eudicot genomes showed appreciable 'shadowing' produced by more ancient polyploidies, resulting in a web of relatedness among contigs which increased genomic complexity. Conclusions A high-resolution genetically-anchored physical map sheds light on Brassica genome organization and advances positional cloning of specific genes, and may help to validate genome sequence assembly and alignment to chromosomes. All the physical mapping data is freely shared at a WebFPC site (http://lulu.pgml.uga.edu/fpc/WebAGCoL/brassica/WebFPC/; Temporarily password-protected: account: pgml; password: 123qwe123

Communication: Quantitative multi-site frequency maps for amide I vibrational spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Reppert, Mike [Department of Chemistry, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Department of Chemistry, University of Chicago, Chicago, Illinois 60637 (United States); Tokmakoff, Andrei, E-mail: tokmakoff@uchicago.edu [Department of Chemistry, University of Chicago, Chicago, Illinois 60637 (United States)

2015-08-14

An accurate method for predicting the amide I vibrational spectrum of a given protein structure has been sought for many years. Significant progress has been made recently by sampling structures from molecular dynamics simulations and mapping local electrostatic variables onto the frequencies of individual amide bonds. Agreement with experiment, however, has remained largely qualitative. Previously, we used dipeptide fragments and isotope-labeled constructs of the protein G mimic NuG2b as experimental standards for developing and testing amide I frequency maps. Here, we combine these datasets to test different frequency-map models and develop a novel method to produce an optimized four-site potential (4P) map based on the CHARMM27 force field. Together with a charge correction for glycine residues, the optimized map accurately describes both experimental datasets, with average frequency errors of 2–3 cm{sup −1}. This 4P map is shown to be convertible to a three-site field map which provides equivalent performance, highlighting the viability of both field- and potential-based maps for amide I spectral modeling. The use of multiple sampling points for local electrostatics is found to be essential for accurate map performance.

Mapping of contaminated sites using mobile gamma spectrometry: Marcassin system

International Nuclear Information System (INIS)

Panza, F.; Demongeot, S.; Crosland, E.; Foissard, B.

2015-01-01

Document available in abstract form only. Full text of publication follows: As part of the development of a tool for use in a nuclear emergency, post-accident situations and contaminated sites, the Institute for Radiation Protection and Nuclear Safety (IRSN) has designed an instrument for mapping natural and artificial radioactivity in soil using in situ gamma spectrometry. The development of this mobile system is based on various studies initiated by IRSN. The tool, named MARCASSIN (Moyen Autoporteur pour la Realisation de Cartographies de l'Activite Sur Sites contamINes, or automotive resource for mapping radioactivity at contaminated sites), has already been used to characterise various types of sites: contaminated soil (Fukushima), old open-pit mines (centre of France) and environmental sites (Paris region). Mounted on a quad-type vehicle, the instrument is composed of a spectrometer, a radiation meter and a global positioning system. Using coordinates and nuclear data, results are given in the form of mapping indicating type of radionuclides, radioactivity level, dose rate and contamination distribution in real-time. To improve detection level above sites where radioactivity levels are low, the system also is capable of processing data. Two of these methods are as follows: the first, 're-meshing', improves the estimate of soil radioactivity by increasing measurement statistics. The results agree with the reference values (soil samples measured in the laboratory), even for normal environmental levels of radioactivity. The second method, for which a patent is pending, is based on a deconvolution of mapping data. Re-processing deducts the impulse response of MARCASSIN from the radiation flux measurements in order to restore the value sought, which is the soil emission rate by radiological energy or activity. A theoretical example demonstrates the possibilities of this method. (authors)

Mapping Changes in a Recovering Mine Site with Hyperspectral Airborne HyMap Imagery (Sotiel, SW Spain

Directory of Open Access Journals (Sweden)

Jorge Buzzi

2014-04-01

Full Text Available Hyperspectral high spatial resolution HyMap data are used to map mine waste from massive sulfide ore deposits, mostly abandoned, on the Iberian Pyrite Belt (southwest Spain. Mine dams, mill tailings and mine dumps in variable states of pyrite oxidation are recognizable. The interpretation of hyperspectral remote sensing requires specific algorithms able to manage high dimensional data compared to multispectral data. The routine of image processing methods used to extract information from hyperspectral data to map geological features is explained, as well as the sequence of algorithms used to produce maps of the mine sites. The mineralogical identification capability of algorithms to produce maps based on archive spectral libraries is discussed. Trends of mineral growth differ spectrally over time according to the geological setting and the recovery state of the mine site. Subtle mineralogical changes are enhanced using the spectral response as indicators of pyrite oxidation intensity of the mine waste piles and pyrite mud tailings. The changes in the surface of the mill tailings deserve a detailed description, as the surfaces are inaccessible to direct observation. Such mineralogical changes respond faithfully to industrial activities or the influence of climate when undisturbed by human influence.

Global Land Survey Impervious Mapping Project Web Site

Science.gov (United States)

DeColstoun, Eric Brown; Phillips, Jacqueline

2014-01-01

The Global Land Survey Impervious Mapping Project (GLS-IMP) aims to produce the first global maps of impervious cover at the 30m spatial resolution of Landsat. The project uses Global Land Survey (GLS) Landsat data as its base but incorporates training data generated from very high resolution commercial satellite data and using a Hierarchical segmentation program called Hseg. The web site contains general project information, a high level description of the science, examples of input and output data, as well as links to other relevant projects.

Vegetation inventory, mapping, and classification report, Fort Bowie National Historic Site

Science.gov (United States)

Studd, Sarah; Fallon, Elizabeth; Crumbacher, Laura; Drake, Sam; Villarreal, Miguel

2013-01-01

A vegetation mapping and characterization effort was conducted at Fort Bowie National Historic Site in 2008-10 by the Sonoran Desert Network office in collaboration with researchers from the Office of Arid lands studies, Remote Sensing Center at the University of Arizona. This vegetation mapping effort was completed under the National Park Service Vegetation Inventory program which aims to complete baseline mapping inventories at over 270 national park units. The vegetation map data was collected to provide park managers with a digital map product that met national standards of spatial and thematic accuracy, while also placing the vegetation into a regional and even national context. Work comprised of three major field phases 1) concurrent field-based classification data collection and mapping (map unit delineation), 2) development of vegetation community types at the National Vegetation Classification alliance or association level and 3) map accuracy assessment. Phase 1 was completed in late 2008 and early 2009. Community type descriptions were drafted to meet the then-current hierarchy (version 1) of the National Vegetation Classification System (NVCS) and these were applied to each of the mapped areas. This classification was developed from both plot level data and censused polygon data (map units) as this project was conducted as a concurrent mapping and classification effort. The third stage of accuracy assessment completed in the fall of 2010 consisted of a complete census of each map unit and was conducted almost entirely by park staff. Following accuracy assessment the map was amended where needed and final products were developed including this report, a digital map and full vegetation descriptions. Fort Bowie National Historic Site covers only 1000 acres yet has a relatively complex landscape, topography and geology. A total of 16 distinct communities were described and mapped at Fort Bowie NHS. These ranged from lush riparian woodlands lining the

Remote Sensing for Mapping RAMSAR Heritage Site at Sungai Pulai Mangrove Forest Reserve, Johor, Malaysia

International Nuclear Information System (INIS)

Hasmadi, I.M.; Pakhriazad, H.Z.; Norlida, K.

2011-01-01

The Sungai Pulai Mangrove Forest Reserve (SPMFR) is the largest reverin mangrove system in Johore. In 2003 about 9,126 ha of the Sungai Pulai mangrove was designated as a RAMSAR site. RAMSAR sites are wetland areas that are deemed to have international importance and are included in the List of Wetlands of International Importance. The SPMFR plays a significant socio-economic role to the adjacent 38 villages. Satellite remote sensing is a useful source of information where it provides timely and complete coverage for vegetation mapping especially in mangroves where the accessibility is difficult. This study was carried out to identify and map land cover types using SPOT-4 imagery at the Sungai Pulai-RAMSAR site and its surrounding areas. Through unsupervised classification technique a total of seven classes of land cover type were mapped, where about 90 % mapping accuracy was gained from the accuracy assessment. Later, vegetation densities were classified into five levels namely very high, high, medium, low and very low based on crown density scale using vegetation indices model such as NDVI, AVI and OSAVI. Results from NDVI and OSAVI model were almost similar but AVI model detected more on medium vegetation which did not show the real ground condition. The study concludes that SPOT-4 imagery was able to discriminate mangrove area clearly from other land covers type. Vegetation indices model can be used as a tool for mapping vegetation density level in the SPMFR and its surrounding area. Therefore VIs models from remote sensing are useful to monitor and manage the mangrove forest for sustainable management and preserve the SPMFR as a RAMSAR site in Peninsular Malaysia. (author)

Characteristics and identification of sites of chagasic ventricular tachycardia by endocardial mapping

Directory of Open Access Journals (Sweden)

Távora Maria Zildany P.

1999-01-01

Full Text Available OBJECTIVE: To study electrophysiological characteristics that enable the identification and ablation of sites of chagasic tachycardia. METHODS: Thirty-one patients with chronic Chagas' heart disease and sustained ventricular tachycardia (SVT underwent electrophysiological study to map and ablate that arrhythmia. Fifteen patients had hemodinamically stable SVT reproducible by programmed ventricular stimulation, 9 men and 6 women with ages ranging from 37 to 67 years and ejection fraction varying from 0.17 to 0.64. Endocardial mapping was performed during SVT in all patients. Radiofrequency (RF current was applied to sites of presystolic activity of at least 30 ms. Entrainment was used to identify reentrant circuits. In both successful and unsuccessful sites of RF current application, electrogram and entrainment were analyzed. RESULTS: Entrainment was obtained during all mapped SVT. In 70.5% of the sites we observed concealed entrainment and ventricular tachycardia termination in the first 15 seconds of RF current application. In the unsuccessful sites, significantly earlier electrical activity was seen than in the successful ones. Concealed entrainment was significantly associated with ventricular tachycardia termination. Bystander areas were not observed. CONCLUSION: The reentrant mechanism was responsible for the genesis of all tachycardias. In 70.5% of the studied sites, the endocardial participation of the slow conducting zone of reentrant circuits was shown. Concealed entrainment was the main electrophysiological parameter associated with successful RF current application. There was no electrophysiological evidence of bystander regions in the mapped circuits of SVT.

An integrated study of spatial multicriteria analysis and mathematical modelling for managed aquifer recharge site suitability mapping and site ranking at Northern Gaza coastal aquifer.

Science.gov (United States)

Rahman, Mohammad Azizur; Rusteberg, Bernd; Uddin, Mohammad Salah; Lutz, Annegret; Saada, Muath Abu; Sauter, Martin

2013-07-30

This paper describes an integrated approach of site suitability mapping and ranking of the most suitable sites, for the implementation of Managed Aquifer Recharge (MAR) projects, using spatial multicriteria decision analysis (SMCDA) techniques and mathematical modelling. The SMCDA procedure contains constraint mapping, site suitability analysis with criteria standardization and weighting, criteria overlay by analytical hierarchy process (AHP) combined with weighted linear combination (WLC) and ordered weighted averaging (OWA), and sensitivity analysis. The hydrogeological impacts of the selected most suitable sites were quantified by using groundwater flow and transport modelling techniques. Finally, ranking of the selected sites was done with the WLC method. The integrated approach is demonstrated by a case study in the coastal aquifer of North Gaza. Constraint mapping shows that 50% of the total study area is suitable for MAR implementation. About 25% of the total area is "very good" and 25% percent is "good" for MAR, according to the site suitability analysis. Six locations were selected and ranked against six representative decision criteria. Long term (year 2003 to year 2040) groundwater flow and transport simulations were performed to quantify the selected criteria under MAR project operation conditions at the selected sites. Finally, the suitability mapping and hydrogeological investigation recommends that the location of the existing infiltration ponds, constructed near the planned North Gaza Wastewater Treatment Plant (NGWWTP) is most suitable for MAR project implementation. This paper concludes that mathematical modelling should be combined with the SMCDA technique in order to select the best location for MAR project implementation. Besides MAR project implementation, the generalised approach can be applicable for any other water resources development project that deals with site selection and implementation. Copyright © 2013 Elsevier Ltd. All rights

Preliminary Correlation Map of Geomorphic Surfaces in North-Central Frenchman Flat, Nevada Test Site

International Nuclear Information System (INIS)

Bechtel Nevada

2005-01-01

This correlation map (scale = 1:12,000) presents the results of a mapping initiative that was part of the comprehensive site characterization required to operate the Area 5 Radioactive Waste Management Site, a low-level radioactive waste disposal facility located in northern Frenchman Flat at the Nevada Test Site. Eight primary map units are recognized for Quaternary surfaces: remnants of six alluvial fan or terrace surfaces, one unit that includes colluvial aprons associated with hill slopes, and one unit for anthropogenically disturbed surfaces. This surficial geology map provides fundamental data on natural processes for reconstruction of the Quaternary history of northern Frenchman Flat, which in turn will aid in the understanding of the natural processes that act to develop the landscape, and the time-frames involved in landscape development. The mapping was conducted using color and color-infrared aerial photographs and field verification of map unit composition and boundaries. Criteria for defining the map unit composition of geomorphic surface units are based on relative geomorphic position, landform morphology, and degree of preservation of surface morphology. The bedrock units identified on this map were derived from previous published mapping efforts and are included for completeness

Construction of barley consensus map showing chromosomal ...

African Journals Online (AJOL)

In the past, it has been difficult to accurately determine the location of many types of barley molecular markers due to the lack of commonality between international barley linkage maps. In this study, a consensus map of barley was constructed from five different maps (OWB, VxHs, KxM, barley consensus 2 and barley ...

MODIS snow cover mapping accuracy in a small mountain catchment – comparison between open and forest sites

Directory of Open Access Journals (Sweden)

G. Blöschl

2012-07-01

Full Text Available Numerous global and regional validation studies have examined MODIS snow mapping accuracy by using measurements at climate stations, which are mainly at open sites. MODIS accuracy in alpine and forested regions is, however, still not well understood. The main objective of this study is to evaluate MODIS (MOD10A1 and MYD10A1 snow cover products in a small experimental catchment by using extensive snow course measurements at open and forest sites. The MODIS accuracy is tested in the Jalovecky creek catchment (northern Slovakia in the period 2000–2011. The results show that the combined Terra and Aqua images enable snow mapping at an overall accuracy of 91.5%. The accuracies at forested, open and mixed land uses at the Červenec sites are 92.7%, 98.3% and 81.8%, respectively. The use of a 2-day temporal filter enables a significant reduction in the number of days with cloud coverage and an increase in overall snow mapping accuracy. In total, the 2-day temporal filter decreases the number of cloudy days from 61% to 26% and increases the snow mapping accuracy to 94%. The results indicate three possible factors leading to misclassification of snow as land: patchy snow cover, limited MODIS geolocation accuracy and mapping algorithm errors. Out of a total of 27 misclassification cases, patchy snow cover, geolocation issues and mapping errors occur in 12, 12 and 3 cases, respectively.

A simulation of Earthquake Loss Estimation in Southeastern Korea using HAZUS and the local site classification Map

Science.gov (United States)

Kang, S.; Kim, K.

2013-12-01

Regionally varying seismic hazards can be estimated using an earthquake loss estimation system (e.g. HAZUS-MH). The estimations for actual earthquakes help federal and local authorities develop rapid, effective recovery measures. Estimates for scenario earthquakes help in designing a comprehensive earthquake hazard mitigation plan. Local site characteristics influence the ground motion. Although direct measurements are desirable to construct a site-amplification map, such data are expensive and time consuming to collect. Thus we derived a site classification map of the southern Korean Peninsula using geologic and geomorphologic data, which are readily available for the entire southern Korean Peninsula. Class B sites (mainly rock) are predominant in the area, although localized areas of softer soils are found along major rivers and seashores. The site classification map is compared with independent site classification studies to confirm our site classification map effectively represents the local behavior of site amplification during an earthquake. We then estimated the losses due to a magnitude 6.7 scenario earthquake in Gyeongju, southeastern Korea, with and without the site classification map. Significant differences in loss estimates were observed. The loss without the site classification map decreased without variation with increasing epicentral distance, while the loss with the site classification map varied from region to region, due to both the epicentral distance and local site effects. The major cause of the large loss expected in Gyeongju is the short epicentral distance. Pohang Nam-Gu is located farther from the earthquake source region. Nonetheless, the loss estimates in the remote city are as large as those in Gyeongju and are attributed to the site effect of soft soil found widely in the area.

Updating the Geologic Maps of the Apollo 15, 16, and 17 Landing Sites

Science.gov (United States)

Garry, W. B.; Mest, S. C.; Yingst, R. A.; Ostrach, L. R.; Petro, N. E.; Cohen, B. A.

2018-06-01

Our team is funded through NASA's Planetary Data Archiving, Restoration, and Tools (PDART) program to produce two new USGS Special Investigation Maps (SIM) for the Apollo 15, 16, and 17 missions: a regional map (1:200K) and a landing-site map (1:24K).

Site characterization and petroleum hydrocarbon plume mapping

Energy Technology Data Exchange (ETDEWEB)

Ravishankar, K. [Harding Lawson Associates, Houston, TX (United States)

1996-12-31

This paper presents a case study of site characterization and hydrocarbon contamination plume mapping/delineation in a gas processing plant in southern Mexico. The paper describes innovative and cost-effective use of passive (non-intrusive) and active (intrusive) techniques, including the use of compound-specific analytical methods for site characterization. The techniques used, on a demonstrative basis, include geophysical, geochemical, and borehole drilling. Geochemical techniques used to delineate the horizontal extent of hydrocarbon contamination at the site include soil gas surveys. The borehole drilling technique used to assess the vertical extent of contamination and confirm geophysical and geochemical data combines conventional hollow-stem auguring with direct push-probe using Geoprobe. Compound-specific analytical methods, such as hydrocarbon fingerprinting and a modified method for gasoline range organics, demonstrate the inherent merit and need for such analyses to properly characterize a site, while revealing the limitations of noncompound-specific total petroleum hydrocarbon analysis. The results indicate that the techniques used in tandem can properly delineate the nature and extent of contamination at a site; often supplement or complement data, while reducing the risk of errors and omissions during the assessment phase; and provide data constructively to focus site-specific remediation efforts. 7 figs.

Development of Rapid and Low Cost Archaeological Site Mapping Using Photogrammetric Technique

International Nuclear Information System (INIS)

Azhar, N A Mohd; Ahmad, Anuar

2014-01-01

In digital photogrammetry, unmanned aerial vehicle (UAV) platform is a new technology that can be used to capture digital images for large scale mapping with accuracy down to centimeter level from various waypoints for archaeological site documentation. UAV is one of the great alternatives to replace piloted aircraft and with combination of non -metric camera, thus it can be applied for small area such as cultural heritage building/ archeological site area. With the recent technology of non-metric cameras, this camera is capable of producing high resolution digital images. This study investigates the application of UAV images for documentation and mapping of a simulated archaeological sites. An archaeological site simulation modelwith dimension of 2.4 m × 3.5 m is used in this study. The accuracy for mapping the archeological sites based on the UAV system is evaluated and analyzed by performing the Root Mean Square Error (RMSE) derived from the differences of coordinates between reference value and the coordinates observed from photogrammetric output such as digital terrain model and orthophoto. In this application, a simulation model was used to simulate the archaeological site excavation. The results clearly demonstrate the potential and the capability of UAV and non-metric camera in providing the accuracy of centimetre level for this application. From this study, it can be concluded that the UAV and the photogrammetric technique procedure satisfied the needs of archaeological sites survey and documentation

Digital Declarations: The Provision of Site Maps under INFCIRC/540 Article 2.a.(iii)

International Nuclear Information System (INIS)

Rutkowski, J.; Keskinen, A.; Steinmaus, K.; Rialhe, A.; Idinger, J.; Balter, E.; Nussbaum, S.

2015-01-01

The modernization of information technology for safeguards is necessary to increase both the availability and the security of safeguards information, a vital asset for Safeguards implementation. The Safeguards Information Management Division's State Infrastructure Analysis Section has initiated several new Member State Support Programme tasks to test and demonstrate how site maps attached to Additional Protocol declarations provided under Article 2.a.(iii) might be submitted to the IAEA in a digital format. This would allow the IAEA to automatically ingest site maps into its Geospatial Exploitation System which would save time and resources as well as result in better, more accurate site maps for the IAEA. The benefits to States include a more well-defined, standardized approach to submitting 2.a.(iii) information. This could mean more consistency across all sites within a country and a simplified annual update process. In addition, creating digital site maps using industry-standard geographically-aware information systems provide tools for data management and data visualization, including temporal changes. The overall verification process would be enhanced since the digital site maps can be easily compared to other data sources, thus enhancing the efficiency and accuracy of verification. Germany, Canada, Finland and Japan have accepted support programme tasks on this subject and agreed to evaluate the provision of digital declaration data on selected nuclear sites. The IAEA will use this opportunity to work with site operators to evaluate what this means to current practices. The IAEA will use the results of these tasks as lessons-learned to evolve and to optimize the process to the benefit of all. A complementary E-poster within this panel section will demonstrate new, more standardized templates and recommended workflows for submission of digital declaration data. (author)

Fishing site mapping using local knowledge provides accurate and ...

African Journals Online (AJOL)

Accurate fishing ground maps are necessary for fisheries monitoring. In Velondriake locally managed marine area (LMMA) we observed that the nomenclature of shared fishing sites (FS) is villages dependent. Additionally, the level of illiteracy makes data collection more complicated, leading to data collectors improvising ...

Image Analysis for Facility Siting: a Comparison of Lowand High-altitude Image Interpretability for Land Use/land Cover Mapping

Science.gov (United States)

Borella, H. M.; Estes, J. E.; Ezra, C. E.; Scepan, J.; Tinney, L. R.

1982-01-01

For two test sites in Pennsylvania the interpretability of commercially acquired low-altitude and existing high-altitude aerial photography are documented in terms of time, costs, and accuracy for Anderson Level II land use/land cover mapping. Information extracted from the imagery is to be used in the evaluation process for siting energy facilities. Land use/land cover maps were drawn at 1:24,000 scale using commercially flown color infrared photography obtained from the United States Geological Surveys' EROS Data Center. Detailed accuracy assessment of the maps generated by manual image analysis was accomplished employing a stratified unaligned adequate class representation. Both 'area-weighted' and 'by-class' accuracies were documented and field-verified. A discrepancy map was also drawn to illustrate differences in classifications between the two map scales. Results show that the 1:24,000 scale map set was more accurate (99% to 94% area-weighted) than the 1:62,500 scale set, especially when sampled by class (96% to 66%). The 1:24,000 scale maps were also more time-consuming and costly to produce, due mainly to higher image acquisition costs.

Satellite Power System (SPS) mapping of exclusion areas for rectenna sites

Science.gov (United States)

Blackburn, J. B., Jr.; Bavinger, B. A.

1978-01-01

The areas of the United States that were not available as potential sites for receiving antennas that are an integral part of the Satellite Power System concept are presented. Thirty-six variables with the potential to exclude the rectenna were mapped and coded in a computer. Some of these variables exclude a rectenna from locating within the area of its spatial influence, and other variables potentially exclude the rectenna. These maps of variables were assembled from existing data and were mapped on a grid system.

RBPmap: a web server for mapping binding sites of RNA-binding proteins.

Science.gov (United States)

Paz, Inbal; Kosti, Idit; Ares, Manuel; Cline, Melissa; Mandel-Gutfreund, Yael

2014-07-01

Regulation of gene expression is executed in many cases by RNA-binding proteins (RBPs) that bind to mRNAs as well as to non-coding RNAs. RBPs recognize their RNA target via specific binding sites on the RNA. Predicting the binding sites of RBPs is known to be a major challenge. We present a new webserver, RBPmap, freely accessible through the website http://rbpmap.technion.ac.il/ for accurate prediction and mapping of RBP binding sites. RBPmap has been developed specifically for mapping RBPs in human, mouse and Drosophila melanogaster genomes, though it supports other organisms too. RBPmap enables the users to select motifs from a large database of experimentally defined motifs. In addition, users can provide any motif of interest, given as either a consensus or a PSSM. The algorithm for mapping the motifs is based on a Weighted-Rank approach, which considers the clustering propensity of the binding sites and the overall tendency of regulatory regions to be conserved. In addition, RBPmap incorporates a position-specific background model, designed uniquely for different genomic regions, such as splice sites, 5' and 3' UTRs, non-coding RNA and intergenic regions. RBPmap was tested on high-throughput RNA-binding experiments and was proved to be highly accurate. © The Author(s) 2014. Published by Oxford University Press on behalf of Nucleic Acids Research.

Snake venom serine proteinases specificity mapping by proteomic identification of cleavage sites.

Science.gov (United States)

Zelanis, André; Huesgen, Pitter F; Oliveira, Ana Karina; Tashima, Alexandre K; Serrano, Solange M T; Overall, Christopher M

2015-01-15

Many snake venom toxins are serine proteases but their specific in vivo targets are mostly unknown. Various act on components of the coagulation cascade, and fibrinolytic and kallikrein-kinin systems to trigger various pathological effects observed in the envenomation. Despite showing high similarity in terms of primary structure snake venom serine proteinases (SVSPs) show exquisite specificity towards macromolecular substrates. Therefore, the characterization of their peptide bond specificity is important for understanding the active site preference associated with effective proteolysis as well as for the design of peptide substrates and inhibitors. Bothrops jararaca contains various SVSPs among which Bothrops protease A is a specific fibrinogenolytic agent and PA-BJ is a platelet-activating enzyme. In this study we used proteome derived peptide libraries in the Proteomic Identification of protease Cleavage Sites (PICS) approach to explore the peptide bond specificity of Bothrops protease A and PA-BJ in order to determine their individual peptide cleavage sequences. A total of 371 cleavage sites (208 for Bothrops protease A and 163 for PA-BJ) were detected and both proteinases displayed a clear preference for arginine at the P1 position. Moreover, the analysis of the specificity profiles of Bothrops protease A and PA-BJ revealed subtle differences in the preferences along P6-P6', despite a common yet unusual preference for Pro at P2. Taken together, these results map the subsite specificity of both SVSPs and shed light in the functional differences between these proteinases. Proteolysis is key to various pathological effects observed upon envenomation by viperid snakes. The use of the Proteomic Identification of protease Cleavage Sites (PICS) approach for the easy mapping of proteinase subsite preferences at both the prime- and non-prime sides concurrently gives rise to a fresh understanding of the interaction of the snake venom serine proteinases with peptide and

Image analysis for facility siting: a comparison of low- and high-altitude image interpretability for land use/land cover mapping

International Nuclear Information System (INIS)

Borella, H.M.; Estes, J.E.; Ezra, C.E.; Scepan, J.; Tinney, L.R.

1982-01-01

For two test sites in Pennsylvania the interpretability of commercially acquired low-altitude and existing high-altitude aerial photography are documented in terms of time, costs, and accuracy for Anderson Level II land use/land cover mapping. Information extracted from the imagery is to be used in the evaluation process for siting energy facilities. Land use/land cover maps were drawn at 1:24,000 scale using commercially flown color infrared photography obtained from the United States Geological Surveys' EROS Data Center. Detailed accuracy assessment of the maps generated by manual image analysis was accomplished employing a stratified unaligned adequate class representation. Both are-weighted and by-class accuracies were documented and field-verified. A discrepancy map was also drawn to illustrate differences in classifications between the two map scales. Results show that the 1:24,000 scale map set was accurate (99% to 94% area-weighted) than the 1:62,500 scale set, especially when sampled by class (96% to 66%). The 1:24,000 scale maps were also more time-consuming and costly to produce, due mainly to higher image acquisition costs

The application of remote sensing in detail land use mapping of RDE site, Puspiptek Serpong

International Nuclear Information System (INIS)

Heni Susiati; Habib Subagio

2016-01-01

Land cover mapping and its development has been performed in a detail scale (1:5000) within the radius of 5 km from the center of Experimental Power Reactor (RDE) site at Kawasan Nuklir Serpong (KNS), PUSPIPTEK Serpong. The objective of this study is to establish land cover database in a detail scale 1:5000 as part of the preparation toward RDE development plan and also to complete the land cover map of a scale 1:10.000. The research method is accomplished in several stages, namely data collection and processing of high-resolution satellite imagery and aerial photographs, field surveys, land use analysis within the radius of 300 - 500 m, 1 km, 2 km, 3 km, 4 km and 5 km from the RDE site as well as analysis of land use change by 2014-2015. Satellite image processing is carried out at Center for Land Mapping and Atlas, Badan Informasi Geospasial (BIG). Data processing is done by using ArcGis and Er Mapper software, whereas the satellite image analysis is executed by using Image Analysis as one of tool in ArcGis software. The result shows that KNS land cover outside the radius of 3 km is a dense residential in many places. Analysis of land use change by year 2014- 2015 shows that vast development of residential has occur which demonstrated by the increase of residential area in North-East of PUSPIPTEK. (author)

Endangered Cultural Heritage: Global Mapping of Protected and Heritage Sites

Science.gov (United States)

2017-07-01

riation of more than 600 repositories of art looted by the Nazi regime and subsequently found throughout Germany and Austria (Edsel 2009; Spirydowicz...heritage sites map function within the ENSITE pro- gram fulfills this need. A search function has been created to data-mine open-source repositories

Coastline Mapping and Cultural Review to Predict Sea Level Rise Impact on Hawaiian Archeological Sites

Science.gov (United States)

Clinton, J.

2017-12-01

Much of Hawaii's history is recorded in archeological sites. Researchers and cultural practitioners have been studying and reconstructing significant archeological sites for generations. Climate change, and more specifically, sea level rise may threaten these sites. Our research records current sea levels and then projects possible consequences to these cultural monuments due to sea level rise. In this mixed methods study, research scientists, cultural practitioners, and secondary students use plane-table mapping techniques to create maps of coastlines and historic sites. Students compare historical records to these maps, analyze current sea level rise trends, and calculate future sea levels. They also gather data through interviews with community experts and kupuna (elders). If climate change continues at projected rates, some historic sites will be in danger of negative impact due to sea level rise. Knowing projected sea levels at specific sites allows for preventative action and contributes to raised awareness of the impacts of climate change to the Hawaiian Islands. Students will share results with the community and governmental agencies in hopes of inspiring action to minimize climate change. It will take collaboration between scientists and cultural communities to inspire future action on climate change.

Rapid Mapping and Deformation Analysis over Cultural Heritage and Rural Sites Based on Persistent Scatterer Interferometry

Directory of Open Access Journals (Sweden)

D. Tapete

2012-01-01

Full Text Available We propose an easy-to-use procedure of “PSI-based rapid mapping and deformation analysis,” to effectively exploit Persistent Scatterer Interferometry (PSI for multispatial/temporal hazard assessment of cultural heritage and rural sites, update the condition report at the scale of entire site and single building, and address the conservation strategies. Advantages and drawbacks of the methodology are critically discussed based on feasibility tests performed over Pitigliano and Bivigliano, respectively, located in Southern and Northern Tuscany, Italy, and representative of hilltop historic towns and countryside settlements chronically affected by natural hazards. We radar-interpreted ERS-1/2 (1992–2000 and ENVISAT (2003–2010 datasets, already processed, respectively with the Permanent Scatterers (PSs and Persistent Scatterers Pairs (PSPs techniques, and assigned the levels of conservation criticality for both the sites. The PSI analysis allowed the zoning of the most unstable sectors of Pitigliano and showed a good agreement with the most updated hazard assessment of the cliff. The reconstruction of past/recent deformation patterns over Bivigliano confirmed the criticality for the Church of San Romolo, supporting the hypothesis of a correlation with local landslide phenomena, as also perceived from the annual motions observed over the entire site, where several landslide bodies are mapped.

Mapping cultural resource sites for the Prince William Sound Graphical Resource Database

International Nuclear Information System (INIS)

Wooley, C. B.; O'Brien, D. K.; Hillman, S. O.

1997-01-01

A software package for mapping digital data 'layers' of environmentally and/or culturally sensitive areas such as seabird colonies, seal haulouts, and sea otter concentrations in Prince William Sound and adjoining areas of southern Alaska has been developed by the Alyeska Pipeline Service Company. The data is to be added to an environmental computer mapping database. More than 1,800 known and reported coastal cultural resource sites have been identified. The database is part of the Prince William Sound Tanker Oil Discharge Prevention and Contingency Plan. The mappable data layers can be used to plan and execute whatever site protection program may be necessary, thus enhancing effective cultural resource protection during an oil spill response. 22 refs., 4 figs

To the question of radioecological mapping of former test sites territories

International Nuclear Information System (INIS)

Grinshtejn, Yu.A.; Syusyura, B.B.

2001-01-01

Performing of large scale (1:25000 - 1:50000) litho-geochemical surveys is necessary if traditional approach is used at mapping alpha- and beta- irradiations ( 239 Pu, 90 Sr) distribution on the territory of the former Semipalatinsk Test Site. Such activities may demand tens of years and great financial supply. Works are performed on estimation of the experience application of schlich geochemical testing used at geological survey with the aim to find more quick technologies of mapping the radionuclide contaminated areas. (author)

CLIP-seq analysis of multi-mapped reads discovers novel functional RNA regulatory sites in the human transcriptome.

Science.gov (United States)

Zhang, Zijun; Xing, Yi

2017-09-19

Crosslinking or RNA immunoprecipitation followed by sequencing (CLIP-seq or RIP-seq) allows transcriptome-wide discovery of RNA regulatory sites. As CLIP-seq/RIP-seq reads are short, existing computational tools focus on uniquely mapped reads, while reads mapped to multiple loci are discarded. We present CLAM (CLIP-seq Analysis of Multi-mapped reads). CLAM uses an expectation-maximization algorithm to assign multi-mapped reads and calls peaks combining uniquely and multi-mapped reads. To demonstrate the utility of CLAM, we applied it to a wide range of public CLIP-seq/RIP-seq datasets involving numerous splicing factors, microRNAs and m6A RNA methylation. CLAM recovered a large number of novel RNA regulatory sites inaccessible by uniquely mapped reads. The functional significance of these sites was demonstrated by consensus motif patterns and association with alternative splicing (splicing factors), transcript abundance (AGO2) and mRNA half-life (m6A). CLAM provides a useful tool to discover novel protein-RNA interactions and RNA modification sites from CLIP-seq and RIP-seq data, and reveals the significant contribution of repetitive elements to the RNA regulatory landscape of the human transcriptome. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

Mapping archaeological sites using digital cartography. Roman settlements from Potaissa to Napoca

Directory of Open Access Journals (Sweden)

FLORIN FODOREAN

2013-11-01

Full Text Available Mapping archeological sites using digital cartography. Roman settlements from potaissa to Napoca. We aim to analyze and correct several archaeological and historical data regarding some settlements included in an official document, issued by the Ministry of Culture from Romania, entitled the List of Historical Monuments (Lista Monumentelor Istorice / LMI. We focused our attention on the Roman road from Potaissa to Napoca, the main imperial road of Dacia. We described the route of the Roman road and corrected the old information in the list of historical monuments regarding the discoveries within the territory of the village of Aiton. Methodologically, we used data from the old literature, the modern Austro-Hungarian maps from the XVIIIth and the XIXth centuries, information from regional gazetteers and different journals. We aimed to offer new insights regarding the accurate location of these settlements and to debate upon the spatial relations of these settlements and their position within the landscape of Dacia. At the beginning of the study, we presented the present situation concerning the databases in Romania covering archaeological sites. The second part of our study discusses how the archaeological sites are recorded in the list of historical monuments. Then we offered several case studies This type of methodological approach will be applied in the future for other areas, in order to reconstruct the former landscape of the province of Dacia, as accurately as possible, using digital tools and modern maps. Our contribution also improved the quality of the data sets used for the topographical descriptions of archaeological sites in Romania.

Geomorphic Surface Maps of Northern Frenchman Flat, Nevada Test Site, Southern Nevada

International Nuclear Information System (INIS)

Bechtel Nevada

2005-01-01

Large-scale (1:6000) surficial geology maps of northern Frenchman Flat were developed in 1995 as part of comprehensive site characterization required to operate a low-level radioactive waste disposal facility in that area. Seven surficial geology maps provide fundamental data on natural processes and are the platform needed to reconstruct the Quaternary history of northern Frenchman Flat. Reconstruction of the Quaternary history provides an understanding of the natural processes that act to develop the landscape, and the time-frames involved in landscape development. The mapping was conducted using color and color-infrared aerial photographs and field verification of map unit composition and boundaries. Criteria for defining the map unit composition of geomorphic surface units are based on relative geomorphic position, landform morphology, and degree of preservation of surface morphology. Seven geomorphic surfaces (Units 1 through 7) are recognized, spanning from the early Quaternary to present time

Mapping Suitable Sites for Setting up Wind Farms: A Case Study of ...

African Journals Online (AJOL)

Mapping Suitable Sites for Setting up Wind Farms: A Case Study of Nyanga District. ... Ethiopian Journal of Environmental Studies and Management ... sources and continuous power shortages make wind energy a very attractive alternative to ...

O-GlcNAc site-mapping of liver X receptor-α and O-GlcNAc transferase.

Science.gov (United States)

Fan, Qiong; Moen, Anders; Anonsen, Jan Haug; Bindesbøll, Christian; Sæther, Thomas; Carlson, Cathrine Rein; Grønning-Wang, Line M

2018-05-05

The Liver X Receptor α (LXRα) belongs to the nuclear receptor superfamily and plays an essential role in regulating cholesterol, lipid and glucose metabolism and inflammatory responses. We have previously shown that LXRα is post-translationally modified by O-linked β-N-acetyl-glucosamine (O-GlcNAc) with increased transcriptional activity. Moreover, we showed that LXRα associates with O-GlcNAc transferase (OGT) in vitro and in vivo in mouse liver. In this study, we report that human LXRα is O-GlcNAc modified in its N-terminal domain (NTD) by identifying a specific O-GlcNAc site S49 and a novel O-GlcNAc modified peptide 20 LWKPGAQDASSQAQGGSSCILRE 42 . However, O-GlcNAc site-mutations did not modulate LXRα transactivation of selected target gene promoters in vitro. Peptide array and co-immunoprecipitation assays demonstrate that LXRα interacts with OGT in its NTD and ligand-binding domain (LBD) in a ligand-independent fashion. Moreover, we map two new O-GlcNAc sites in the longest OGT isoform (ncOGT): S437 in the tetratricopeptide repeat (TPR) 13 domain and T1043 in the far C-terminus, and a new O-GlcNAc modified peptide (amino acids 826-832) in the intervening region (Int-D) within the catalytic domain. We also map four new O-GlcNAc sites in the short isoform sOGT: S391, T393, S399 and S437 in the TPRs 11-13 domain. Future studies will reveal the biological role of identified O-GlcNAc sites in LXRα and OGT. Copyright © 2018 Elsevier Inc. All rights reserved.

High-definition mapping of retroviral integration sites defines the fate of allogeneic T cells after donor lymphocyte infusion.

Directory of Open Access Journals (Sweden)

Claudia Cattoglio

2010-12-01

Full Text Available The infusion of donor lymphocytes transduced with a retroviral vector expressing the HSV-TK suicide gene in patients undergoing hematopoietic stem cell transplantation for leukemia/lymphoma promotes immune reconstitution and prevents infections and graft-versus-host disease. Analysis of the clonal dynamics of genetically modified lymphocytes in vivo is of crucial importance to understand the potential genotoxic risk of this therapeutic approach. We used linear amplification-mediated PCR and pyrosequencing to build a genome-wide, high-definition map of retroviral integration sites in the genome of peripheral blood T cells from two different donors and used gene expression profiling and bioinformatics to associate integration clusters to transcriptional activity and to genetic and epigenetic features of the T cell genome. Comparison with matched random controls and with integrations obtained from CD34(+ hematopoietic stem/progenitor cells showed that integration clusters occur within chromatin regions bearing epigenetic marks associated with active promoters and regulatory elements in a cell-specific fashion. Analysis of integration sites in T cells obtained ex vivo two months after infusion showed no evidence of integration-related clonal expansion or dominance, but rather loss of cells harboring integration events interfering with RNA post-transcriptional processing. The study shows that high-definition maps of retroviral integration sites are a powerful tool to analyze the fate of genetically modified T cells in patients and the biological consequences of retroviral transduction.

Mapping with Drupal

CERN Document Server

Palazzolo, Alan

2011-01-01

Build beautiful interactive maps on your Drupal website, and tell engaging visual stories with your data. This concise guide shows you how to create custom geographical maps from top to bottom, using Drupal 7 tools and out-of-the-box modules. You'll learn how mapping works in Drupal, with examples on how to use intuitive interfaces to map local events, businesses, groups, and other custom data. Although building maps with Drupal can be tricky, this book helps you navigate the system's complexities for creating sophisticated maps that match your site design. Get the knowledge and tools you ne

Contribution of physical modelling to climate-driven landslide hazard mapping: an alpine test site

Science.gov (United States)

Vandromme, R.; Desramaut, N.; Baills, A.; Hohmann, A.; Grandjean, G.; Sedan, O.; Mallet, J. P.

2012-04-01

The aim of this work is to develop a methodology for integrating climate change scenarios into quantitative hazard assessment and especially their precipitation component. The effects of climate change will be different depending on both the location of the site and the type of landslide considered. Indeed, mass movements can be triggered by different factors. This paper describes a methodology to address this issue and shows an application on an alpine test site. Mechanical approaches represent a solution for quantitative landslide susceptibility and hazard modeling. However, as the quantity and the quality of data are generally very heterogeneous at a regional scale, it is necessary to take into account the uncertainty in the analysis. In this perspective, a new hazard modeling method is developed and integrated in a program named ALICE. This program integrates mechanical stability analysis through a GIS software taking into account data uncertainty. This method proposes a quantitative classification of landslide hazard and offers a useful tool to gain time and efficiency in hazard mapping. However, an expertise approach is still necessary to finalize the maps. Indeed it is the only way to take into account some influent factors in slope stability such as heterogeneity of the geological formations or effects of anthropic interventions. To go further, the alpine test site (Barcelonnette area, France) is being used to integrate climate change scenarios into ALICE program, and especially their precipitation component with the help of a hydrological model (GARDENIA) and the regional climate model REMO (Jacob, 2001). From a DEM, land-cover map, geology, geotechnical data and so forth the program classifies hazard zones depending on geotechnics and different hydrological contexts varying in time. This communication, realized within the framework of Safeland project, is supported by the European Commission under the 7th Framework Programme for Research and Technological

MicroCT analysis of calcium/phosphorus ratio maps at different bone sites

Energy Technology Data Exchange (ETDEWEB)

Speller, R. [Medical Physics and Bioengineering Department, UCL, London, WC1E 6BT (United Kingdom)]. E-mail: rspeller@medphys.ucl.ac.uk; Pani, S. [Department of Physics, University of Trieste (Italy); Tzaphlidou, M. [Lab Medical Physics, Medical School, University of Ioannina, 45110 Ioannina (Greece); Horrocks, J. [Clinical Physics Group, St Bartholomew' s Hospital, London, EC1A 6BT (United Kingdom)

2005-08-11

The Ca/P ratio was measured in cortical bone samples from the femoral neck, front and rear tibia of rats, rabbits and lambs using synchrotron microCT. Use of a monoenergetic X-ray beam, as provided by the synchrotron facility, generates accurate 3-D maps of the linear attenuation coefficient within the sample and hence gives the ability to map different chemical components. Data were taken at 20keV for each bone sample and calibration phantoms. From the 3-D data sets, multiple 2-D slices were reconstructed with a slice thickness of {approx}28{mu}m and converted to Ca/P ratios using the calibration phantom results. Average values for each animal and bone site were estimated. Differences between the same bone sites from different animals are not significant (0.3sites and different animals are highly significant (p<10{sup -3}) demonstrating a dependence upon lifestyle and bone use. The spatial distribution of Ca/P was found to be non-uniform for some bones and some animals possibly indicating the structural mechanism for obtaining bone strength.

Archaeological field survey automation: concurrent multisensor site mapping and automated analysis

Science.gov (United States)

Józefowicz, Mateusz; Sokolov, Oleksandr; Meszyński, Sebastian; Siemińska, Dominika; Kołosowski, Przemysław

2016-04-01

ABM SE develops mobile robots (rovers) used for analog research of Mars exploration missions. The rovers are all-terrain exploration platforms, carrying third-party payloads: scientific instrumentation. "Wisdom" ground penetrating radar for Exomars mission has been tested onboard, as well as electrical resistivity module and other devices. Robot has operated in various environments, such as Central European countryside, Dachstein ice caves or Sahara, Morocco (controlled remotely via satellite from Toruń, Poland. Currently ABM SE works on local and global positioning system for a Mars rover basing on image and IMU data. This is performed under a project from ESA. In the next Mars rover missions a Mars GIS model will be build, including an acquired GPR profile, DEM and regular image data, integrated into a concurrent 3D terrain model. It is proposed to use similar approach in surveys of archaeological sites, especially those, where solid architecture remains can be expected at shallow depths or being partially exposed. It is possible to deploy a rover that will concurrently map a selected site with GPR, 2D and 3D cameras to create a site model. The rover image processing algorithms are capable of automatic tracing of distinctive features (such as exposed structure remains on a desert ground, differences in color of the ground, etc.) and to mark regularities on a created map. It is also possible to correlate the 3D map with an aerial photo taken under any angle to achieve interpretation synergy. Currently the algorithms are an interpretation aid and their results must be confirmed by a human. The advantages of a rover over traditional approaches, such as a manual cart or a drone include: a) long hours of continuous work or work in unfavorable environment, such as high desert, frozen water pools or large areas, b) concurrent multisensory data acquisition, c) working from the ground level enables capturing of sites obstructed from the air (trees), d) it is possible to

Testing a small UAS for mapping artisanal diamond mining sites in Africa

Science.gov (United States)

Malpeli, Katherine C.; Chirico, Peter G.

2015-01-01

Remote sensing technology is advancing at an unprecedented rate. At the forefront of the new technological developments are unmanned aircraft systems (UAS). The advent of small, lightweight, low-cost, and user-friendly UAS is greatly expanding the potential applications of remote sensing technology and improving the set of tools available to researchers seeking to map and monitor terrain from above. In this article, we explore the applications of a small UAS for mapping informal diamond mining sites in Africa. We found that this technology provides aerial imagery of unparalleled resolution in a data-sparse, difficult to access, and remote terrain.

Looking for an old map

Science.gov (United States)

,

1996-01-01

Many people want maps that show an area of the United States as it existed many years ago. These are called historical maps, and there are two types. The most common type consists of special maps prepared by commercial firms to show such historical features as battle-fields, military routes, or the paths taken by famous travelers. Typically, these maps are for sale to tourists at the sites of historical events. The other type is the truly old map--one compiled by a surveyor or cartographer many years ago. Lewis and Clark, for example, made maps of their journeys into the Northwest Territories in 1803-6, and originals of some of these maps still exist.

Remote Sensing Analysis Techniques and Sensor Requirements to Support the Mapping of Illegal Domestic Waste Disposal Sites in Queensland, Australia

Directory of Open Access Journals (Sweden)

Katharine Glanville

2015-10-01

Full Text Available Illegal disposal of waste is a significant management issue for contemporary governments with waste posing an economic, social, and environmental risk. An improved understanding of the distribution of illegal waste disposal sites is critical to enhance the cost-effectiveness and efficiency of waste management efforts. Remotely sensed data has the potential to address this knowledge gap. However, the literature regarding the use of remote sensing to map illegal waste disposal sites is incomplete. This paper aims to analyze existing remote sensing methods and sensors used to monitor and map illegal waste disposal sites. The purpose of this paper is to support the evaluation of existing remote sensing methods for mapping illegal domestic waste sites in Queensland, Australia. Recent advances in technology and the acquisition of very high-resolution remote sensing imagery provide an important opportunity to (1 revisit established analysis techniques for identifying illegal waste disposal sites, (2 examine the applicability of different remote sensors for illegal waste disposal detection, and (3 identify opportunities for future research to increase the accuracy of any illegal waste disposal mapping products.

Insurance Applications of Active Fault Maps Showing Epistemic Uncertainty

Science.gov (United States)

Woo, G.

2005-12-01

Insurance loss modeling for earthquakes utilizes available maps of active faulting produced by geoscientists. All such maps are subject to uncertainty, arising from lack of knowledge of fault geometry and rupture history. Field work to undertake geological fault investigations drains human and monetary resources, and this inevitably limits the resolution of fault parameters. Some areas are more accessible than others; some may be of greater social or economic importance than others; some areas may be investigated more rapidly or diligently than others; or funding restrictions may have curtailed the extent of the fault mapping program. In contrast with the aleatory uncertainty associated with the inherent variability in the dynamics of earthquake fault rupture, uncertainty associated with lack of knowledge of fault geometry and rupture history is epistemic. The extent of this epistemic uncertainty may vary substantially from one regional or national fault map to another. However aware the local cartographer may be, this uncertainty is generally not conveyed in detail to the international map user. For example, an area may be left blank for a variety of reasons, ranging from lack of sufficient investigation of a fault to lack of convincing evidence of activity. Epistemic uncertainty in fault parameters is of concern in any probabilistic assessment of seismic hazard, not least in insurance earthquake risk applications. A logic-tree framework is appropriate for incorporating epistemic uncertainty. Some insurance contracts cover specific high-value properties or transport infrastructure, and therefore are extremely sensitive to the geometry of active faulting. Alternative Risk Transfer (ART) to the capital markets may also be considered. In order for such insurance or ART contracts to be properly priced, uncertainty should be taken into account. Accordingly, an estimate is needed for the likelihood of surface rupture capable of causing severe damage. Especially where a

Mapping site-based construction workers’ motivation: Expectancy theory approach

Directory of Open Access Journals (Sweden)

Parviz Ghoddousi

2014-03-01

Full Text Available The aim of this study is to apply a recently proposed model of motivation based on expectancy theory to site-based workers in the construction context and confirm the validity of this model for the construction industry. The study drew upon data from 194 site-based construction workers in Iran to test the proposed model of motivation. To this end, the structural equation modelling (SEM approach based on the confirmatory factor analysis (CFA technique was deployed. The study reveals that the proposed model of expectancy theory incorporating five indicators (i.e. intrinsic instrumentality, extrinsic instrumentality, intrinsic valence, extrinsic valence and expectancy is able to map the process of construction workers’ motivation. Nonetheless, the findings posit that intrinsic indicators could be more effective than extrinsic ones. This proffers the necessity of construction managers placing further focus on intrinsic motivators to motivate workers. 

Mapping site-based construction workers’ motivation: Expectancy theory approach

Directory of Open Access Journals (Sweden)

Parviz Ghoddousi

2014-03-01

Full Text Available The aim of this study is to apply a recently proposed model of motivation based on expectancy theory to site-based workers in the construction context and confirm the validity of this model for the construction industry. The study drew upon data from 194 site-based construction workers in Iran to test the proposed model of motivation. To this end, the structural equation modelling (SEM approach based on the confirmatory factor analysis (CFA technique was deployed. The study reveals that the proposed model of expectancy theory incorporating five indicators (i.e. intrinsic instrumentality, extrinsic instrumentality, intrinsic valence, extrinsic valence and expectancy is able to map the process of construction workers’ motivation. Nonetheless, the findings posit that intrinsic indicators could be more effective than extrinsic ones. This proffers the necessity of construction managers placing further focus on intrinsic motivators to motivate workers.

Intra-operative multi-site stimulation: Expanding methodology for cortical brain mapping of language functions.

Science.gov (United States)

Gonen, Tal; Gazit, Tomer; Korn, Akiva; Kirschner, Adi; Perry, Daniella; Hendler, Talma; Ram, Zvi

2017-01-01

Direct cortical stimulation (DCS) is considered the gold-standard for functional cortical mapping during awake surgery for brain tumor resection. DCS is performed by stimulating one local cortical area at a time. We present a feasibility study using an intra-operative technique aimed at improving our ability to map brain functions which rely on activity in distributed cortical regions. Following standard DCS, Multi-Site Stimulation (MSS) was performed in 15 patients by applying simultaneous cortical stimulations at multiple locations. Language functioning was chosen as a case-cognitive domain due to its relatively well-known cortical organization. MSS, performed at sites that did not produce disruption when applied in a single stimulation point, revealed additional language dysfunction in 73% of the patients. Functional regions identified by this technique were presumed to be significant to language circuitry and were spared during surgery. No new neurological deficits were observed in any of the patients following surgery. Though the neuro-electrical effects of MSS need further investigation, this feasibility study may provide a first step towards sophistication of intra-operative cortical mapping.

Construction of barley consensus map showing chromosomal ...

African Journals Online (AJOL)

GRACE

2006-02-02

Feb 2, 2006 ... the purpose of this consensus map (containing QTL) is to provide a tool for scientists to accurately locate molecular markers to ... community with powerful tools for comparative genomics. (Gai et al., 2000; Mekhdov et al., ...... and controlled by almost the same loci (Marquez et al.,. 2000). In the present study ...

Retroviral DNA integration: ASLV, HIV, and MLV show distinct target site preferences.

Directory of Open Access Journals (Sweden)

Rick S Mitchell

2004-08-01

Full Text Available The completion of the human genome sequence has made possible genome-wide studies of retroviral DNA integration. Here we report an analysis of 3,127 integration site sequences from human cells. We compared retroviral vectors derived from human immunodeficiency virus (HIV, avian sarcoma-leukosis virus (ASLV, and murine leukemia virus (MLV. Effects of gene activity on integration targeting were assessed by transcriptional profiling of infected cells. Integration by HIV vectors, analyzed in two primary cell types and several cell lines, strongly favored active genes. An analysis of the effects of tissue-specific transcription showed that it resulted in tissue-specific integration targeting by HIV, though the effect was quantitatively modest. Chromosomal regions rich in expressed genes were favored for HIV integration, but these regions were found to be interleaved with unfavorable regions at CpG islands. MLV vectors showed a strong bias in favor of integration near transcription start sites, as reported previously. ASLV vectors showed only a weak preference for active genes and no preference for transcription start regions. Thus, each of the three retroviruses studied showed unique integration site preferences, suggesting that virus-specific binding of integration complexes to chromatin features likely guides site selection.

MicroCT analysis of calcium/phosphorus ratio maps at different bone sites

International Nuclear Information System (INIS)

Speller, R.; Pani, S.; Tzaphlidou, M.; Horrocks, J.

2005-01-01

The Ca/P ratio was measured in cortical bone samples from the femoral neck, front and rear tibia of rats, rabbits and lambs using synchrotron microCT. Use of a monoenergetic X-ray beam, as provided by the synchrotron facility, generates accurate 3-D maps of the linear attenuation coefficient within the sample and hence gives the ability to map different chemical components. Data were taken at 20keV for each bone sample and calibration phantoms. From the 3-D data sets, multiple 2-D slices were reconstructed with a slice thickness of ∼28μm and converted to Ca/P ratios using the calibration phantom results. Average values for each animal and bone site were estimated. Differences between the same bone sites from different animals are not significant (0.3 -3 ) demonstrating a dependence upon lifestyle and bone use. The spatial distribution of Ca/P was found to be non-uniform for some bones and some animals possibly indicating the structural mechanism for obtaining bone strength

Human papilloma viruses and cervical tumours: mapping of integration sites and analysis of adjacent cellular sequences

International Nuclear Information System (INIS)

Klimov, Eugene; Vinokourova, Svetlana; Moisjak, Elena; Rakhmanaliev, Elian; Kobseva, Vera; Laimins, Laimonis; Kisseljov, Fjodor; Sulimova, Galina

2002-01-01

In cervical tumours the integration of human papilloma viruses (HPV) transcripts often results in the generation of transcripts that consist of hybrids of viral and cellular sequences. Mapping data using a variety of techniques has demonstrated that HPV integration occurred without obvious specificity into human genome. However, these techniques could not demonstrate whether integration resulted in the generation of transcripts encoding viral or viral-cellular sequences. The aim of this work was to map the integration sites of HPV DNA and to analyse the adjacent cellular sequences. Amplification of the INTs was done by the APOT technique. The APOT products were sequenced according to standard protocols. The analysis of the sequences was performed using BLASTN program and public databases. To localise the INTs PCR-based screening of GeneBridge4-RH-panel was used. Twelve cellular sequences adjacent to integrated HPV16 (INT markers) expressed in squamous cell cervical carcinomas were isolated. For 11 INT markers homologous human genomic sequences were readily identified and 9 of these showed significant homologies to known genes/ESTs. Using the known locations of homologous cDNAs and the RH-mapping techniques, mapping studies showed that the INTs are distributed among different human chromosomes for each tumour sample and are located in regions with the high levels of expression. Integration of HPV genomes occurs into the different human chromosomes but into regions that contain highly transcribed genes. One interpretation of these studies is that integration of HPV occurs into decondensed regions, which are more accessible for integration of foreign DNA

GenProBiS: web server for mapping of sequence variants to protein binding sites.

Science.gov (United States)

Konc, Janez; Skrlj, Blaz; Erzen, Nika; Kunej, Tanja; Janezic, Dusanka

2017-07-03

Discovery of potentially deleterious sequence variants is important and has wide implications for research and generation of new hypotheses in human and veterinary medicine, and drug discovery. The GenProBiS web server maps sequence variants to protein structures from the Protein Data Bank (PDB), and further to protein-protein, protein-nucleic acid, protein-compound, and protein-metal ion binding sites. The concept of a protein-compound binding site is understood in the broadest sense, which includes glycosylation and other post-translational modification sites. Binding sites were defined by local structural comparisons of whole protein structures using the Protein Binding Sites (ProBiS) algorithm and transposition of ligands from the similar binding sites found to the query protein using the ProBiS-ligands approach with new improvements introduced in GenProBiS. Binding site surfaces were generated as three-dimensional grids encompassing the space occupied by predicted ligands. The server allows intuitive visual exploration of comprehensively mapped variants, such as human somatic mis-sense mutations related to cancer and non-synonymous single nucleotide polymorphisms from 21 species, within the predicted binding sites regions for about 80 000 PDB protein structures using fast WebGL graphics. The GenProBiS web server is open and free to all users at http://genprobis.insilab.org. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

AMCO Off-Site Air Monitoring Map Service, Oakland CA, 2017, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — This map service contains a single layer: Off-Site Air Monitors. The layer draws at all scales. Full FGDC metadata for the layer may be found by clicking the layer...

Construction of a high-density genetic map for grape using next generation restriction-site associated DNA sequencing

Directory of Open Access Journals (Sweden)

Wang Nian

2012-08-01

Full Text Available Abstract Background Genetic mapping and QTL detection are powerful methodologies in plant improvement and breeding. Construction of a high-density and high-quality genetic map would be of great benefit in the production of superior grapes to meet human demand. High throughput and low cost of the recently developed next generation sequencing (NGS technology have resulted in its wide application in genome research. Sequencing restriction-site associated DNA (RAD might be an efficient strategy to simplify genotyping. Combining NGS with RAD has proven to be powerful for single nucleotide polymorphism (SNP marker development. Results An F1 population of 100 individual plants was developed. In-silico digestion-site prediction was used to select an appropriate restriction enzyme for construction of a RAD sequencing library. Next generation RAD sequencing was applied to genotype the F1 population and its parents. Applying a cluster strategy for SNP modulation, a total of 1,814 high-quality SNP markers were developed: 1,121 of these were mapped to the female genetic map, 759 to the male map, and 1,646 to the integrated map. A comparison of the genetic maps to the published Vitis vinifera genome revealed both conservation and variations. Conclusions The applicability of next generation RAD sequencing for genotyping a grape F1 population was demonstrated, leading to the successful development of a genetic map with high density and quality using our designed SNP markers. Detailed analysis revealed that this newly developed genetic map can be used for a variety of genome investigations, such as QTL detection, sequence assembly and genome comparison.

Mapping subsurface pathways for contaminant migration at a proposed low level waste disposal site using electromagnetic methods

International Nuclear Information System (INIS)

Pin, F.G.; Ketelle, R.H.

1984-01-01

Electromagnetic methods have been used to measure apparent terrain conductivity in the downstream portion of a watershed in which a waste disposal site is proposed. At that site, the pathways for waste migration in ground water are controlled by subsurface channels. The channels are identified using isocurves of measured apparent conductivity. Two upstream channel branches are found to merge into a single downstream channel which constitutes the main drainage path out of the watershed. The identification and mapping of the ground water pathways is an important contribution to the site characterization study and the pathways analysis. The direct applications of terrain conductivity mapping to the planning of the monitoring program, the hydrogeological testing, and the modeling study are demonstrated. 7 references, 4 figures

Evaluation of Story Maps to Enhance Public Engagement and Communication at Legacy Management Sites – 17334

Energy Technology Data Exchange (ETDEWEB)

Castillo, Darina [U.S. Department of Energy, Office of Legacy Management; Carpenter, Cliff [U.S. Department of Energy, Office of Legacy Management; Linard, Joshua [U.S. Department of Energy, Office of Legacy Management; Picel, Mary [Argonne National Lab. (ANL), Argonne, IL (United States)

2017-03-05

Story Maps are being used in both public and private sectors to convey information to stakeholders, create enterprise platforms, and assist in decision making. Story Maps are web applications that combine maps, narrative text, images, and multimedia content to provide information. These applications provide a user-friendly platform to share the remarkable history of our sites, the complexity of their contamination and remediation, successes we achieve in our LTS&M activities, and even the challenges we face as we aim to fulfill our mission.

Applying Nitrogen Site-Specifically Using Soil Electrical Conductivity Maps and Precision Agriculture Technology

Directory of Open Access Journals (Sweden)

E.D. Lund

2001-01-01

Full Text Available Soil texture varies significantly within many agricultural fields. The physical properties of soil, such as soil texture, have a direct effect on water holding capacity, cation exchange capacity, crop yield, production capability, and nitrogen (N loss variations within a field. In short, mobile nutrients are used, lost, and stored differently as soil textures vary. A uniform application of N to varying soils results in a wide range of N availability to the crop. N applied in excess of crop usage results in a waste of the grower’s input expense, a potential negative effect on the environment, and in some crops a reduction of crop quality, yield, and harvestability. Inadequate N levels represent a lost opportunity for crop yield and profit. The global positioning system (GPS-referenced mapping of bulk soil electrical conductivity (EC has been shown to serve as an effective proxy for soil texture and other soil properties. Soils with a high clay content conduct more electricity than coarser textured soils, which results in higher EC values. This paper will describe the EC mapping process and provide case studies of site-specific N applications based on EC maps. Results of these case studies suggest that N can be managed site-specifically using a variety of management practices, including soil sampling, variable yield goals, and cropping history.

Canopy Fuel Load Mapping of Mediterranean Pine Sites Based on Individual Tree-Crown Delineation

Directory of Open Access Journals (Sweden)

Giorgos Mallinis

2013-12-01

Full Text Available This study presents an individual tree-crown-based approach for canopy fuel load estimation and mapping in two Mediterranean pine stands. Based on destructive sampling, an allometric equation was developed for the estimation of crown fuel weight considering only pine crown width, a tree characteristic that can be estimated from passive imagery. Two high resolution images were used originally for discriminating Aleppo and Calabrian pines crown regions through a geographic object based image analysis approach. Subsequently, the crown region images were segmented using a watershed segmentation algorithm and crown width was extracted. The overall accuracy of the tree crown isolation expressed through a perfect match between the reference and the delineated crowns was 34.00% for the Kassandra site and 48.11% for the Thessaloniki site, while the coefficient of determination between the ground measured and the satellite extracted crown width was 0.5. Canopy fuel load values estimated in the current study presented mean values from 1.29 ± 0.6 to 1.65 ± 0.7 kg/m2 similar to other conifers worldwide. Despite the modest accuracies attained in this first study of individual tree crown fuel load mapping, the combination of the allometric equations with satellite-based extracted crown width information, can contribute to the spatially explicit mapping of canopy fuel load in Mediterranean areas. These maps can be used among others in fire behavior prediction, in fuel reduction treatments prioritization and during active fire suppression.

Collaborative community hazard exposure mapping: Distant Early Warning radar sites in Alaska's North Slope

Science.gov (United States)

Brady, M.

2015-12-01

A method to produce hazard exposure maps that are developed in collaboration with local coastal communities is the focus of this research. Typically efforts to map community exposure to climate threats over large areas have limited consideration of local perspectives about associated risks, constraining their utility for local management. This problem is especially acute in remote locations such as the Arctic where there are unique vulnerabilities to coastal threats that can be fully understood only through inclusion of community stakeholders. Through collaboration with community members, this study identifies important coastal assets and places and surveys local perspectives of exposure to climate threats along Alaska's vast North Slope coastline spanning multiple municipalities. To model physical exposure, the study adapts the U.S. Geological Survey's (USGS) coastal vulnerability index (CVI) to the Arctic context by incorporating the effects of open water distance determined by sea ice extent, and assigning CVI values to coastal assets and places according to direction and proximity. The study found that in addition to concerns about exposed municipal and industrial assets, North Slope communities viewed exposure of traditional activity sites as presenting a particular risk for communities. Highly exposed legacy Cold War Distant Early Warning Line sites are of particular concern with impacts ranging from financial risk to contamination of sensitive coastal marine environments. This research demonstrates a method to collaboratively map community exposure to coastal climate threats to better understand local risks and produce locally usable exposure maps.

AMCO On-Site Air Monitoring Map Service, Oakland CA, Live 2017, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — This map service contains the following layers: All On-Site Air Monitors, TCE, PCE, and Vinyl Chloride. The layers draws at all scales. Full FGDC metadata for the...

Mapping of mosquito breeding sites in malaria endemic areas in Pos Lenjang, Kuala Lipis, Pahang, Malaysia

Directory of Open Access Journals (Sweden)

Ahmad Rohani

2011-12-01

Full Text Available Abstract Background The application of the Geographic Information Systems (GIS to the study of vector transmitted diseases considerably improves the management of the information obtained from the field survey and facilitates the study of the distribution patterns of the vector species. Methods As part of a study to assess remote sensing data as a tool for vector mapping, geographical features like rivers, small streams, forest, roads and residential area were digitized from the satellite images and overlaid with entomological data. Map of larval breeding habitats distribution and map of malaria transmission risk area were developed using a combination of field data, satellite image analysis and GIS technique. All digital data in the GIS were displayed in the WGS 1984 coordinate system. Six occasions of larval surveillance were also conducted to determine the species of mosquitoes, their characteristics and the abundance of habitats. Results Larval survey studies showed that anopheline and culicine larvae were collected and mapped from 79 and 67 breeding sites respectively. Breeding habitats were located at 100-400 m from human settlement. Map of villages with 400 m buffer zone visualizes that more than 80% of Anopheles maculatus s.s. immature habitats were found within the buffer zone. Conclusions This study amplifies the need for a broadening of the GIS approach which is emphasized with the aim of rejuvenating the dynamic aspect of entomological studies in Malaysia. In fact, the use of such basic GIS platforms promote a more rational basis for strategic planning and management in the control of endemic diseases at the national level.

Mapping of mosquito breeding sites in malaria endemic areas in Pos Lenjang, Kuala Lipis, Pahang, Malaysia.

Science.gov (United States)

Ahmad, Rohani; Ali, Wan N W M; Nor, Zurainee M; Ismail, Zamree; Hadi, Azahari A; Ibrahim, Mohd N; Lim, Lee H

2011-12-13

The application of the Geographic Information Systems (GIS) to the study of vector transmitted diseases considerably improves the management of the information obtained from the field survey and facilitates the study of the distribution patterns of the vector species. As part of a study to assess remote sensing data as a tool for vector mapping, geographical features like rivers, small streams, forest, roads and residential area were digitized from the satellite images and overlaid with entomological data. Map of larval breeding habitats distribution and map of malaria transmission risk area were developed using a combination of field data, satellite image analysis and GIS technique. All digital data in the GIS were displayed in the WGS 1984 coordinate system. Six occasions of larval surveillance were also conducted to determine the species of mosquitoes, their characteristics and the abundance of habitats. Larval survey studies showed that anopheline and culicine larvae were collected and mapped from 79 and 67 breeding sites respectively. Breeding habitats were located at 100-400 m from human settlement. Map of villages with 400 m buffer zone visualizes that more than 80% of Anopheles maculatus s.s. immature habitats were found within the buffer zone. This study amplifies the need for a broadening of the GIS approach which is emphasized with the aim of rejuvenating the dynamic aspect of entomological studies in Malaysia. In fact, the use of such basic GIS platforms promote a more rational basis for strategic planning and management in the control of endemic diseases at the national level.

Mapping of mosquito breeding sites in malaria endemic areas in Pos Lenjang, Kuala Lipis, Pahang, Malaysia

Science.gov (United States)

2011-01-01

Background The application of the Geographic Information Systems (GIS) to the study of vector transmitted diseases considerably improves the management of the information obtained from the field survey and facilitates the study of the distribution patterns of the vector species. Methods As part of a study to assess remote sensing data as a tool for vector mapping, geographical features like rivers, small streams, forest, roads and residential area were digitized from the satellite images and overlaid with entomological data. Map of larval breeding habitats distribution and map of malaria transmission risk area were developed using a combination of field data, satellite image analysis and GIS technique. All digital data in the GIS were displayed in the WGS 1984 coordinate system. Six occasions of larval surveillance were also conducted to determine the species of mosquitoes, their characteristics and the abundance of habitats. Results Larval survey studies showed that anopheline and culicine larvae were collected and mapped from 79 and 67 breeding sites respectively. Breeding habitats were located at 100-400 m from human settlement. Map of villages with 400 m buffer zone visualizes that more than 80% of Anopheles maculatus s.s. immature habitats were found within the buffer zone. Conclusions This study amplifies the need for a broadening of the GIS approach which is emphasized with the aim of rejuvenating the dynamic aspect of entomological studies in Malaysia. In fact, the use of such basic GIS platforms promote a more rational basis for strategic planning and management in the control of endemic diseases at the national level. PMID:22166101

Quantification and site-specification of the support practice factor when mapping soil erosion risk associated with olive plantations in the Mediterranean island of Crete.

Science.gov (United States)

Karydas, Christos G; Sekuloska, Tijana; Silleos, Georgios N

2009-02-01

Due to inappropriate agricultural management practices, soil erosion is becoming one of the most dangerous forms of soil degradation in many olive farming areas in the Mediterranean region, leading to significant decrease of soil fertility and yield. In order to prevent further soil degradation, proper measures are necessary to be locally implemented. In this perspective, an increase in the spatial accuracy of remote sensing datasets and advanced image analysis are significant tools necessary and efficient for mapping soil erosion risk on a fine scale. In this study, the Revised Universal Soil Loss Equation (RUSLE) was implemented in the spatial domain using GIS, while a very high resolution satellite image, namely a QuickBird image, was used for deriving cover management (C) and support practice (P) factors, in order to map the risk of soil erosion in Kolymvari, a typical olive farming area in the island of Crete, Greece. The results comprised a risk map of soil erosion when P factor was taken uniform (conventional approach) and a risk map when P factor was quantified site-specifically using object-oriented image analysis. The results showed that the QuickBird image was necessary in order to achieve site-specificity of the P factor and therefore to support fine scale mapping of soil erosion risk in an olive cultivation area, such as the one of Kolymvari in Crete. Increasing the accuracy of the QB image classification will further improve the resulted soil erosion mapping.

A ChIP-Seq benchmark shows that sequence conservation mainly improves detection of strong transcription factor binding sites.

Directory of Open Access Journals (Sweden)

Tony Håndstad

Full Text Available BACKGROUND: Transcription factors are important controllers of gene expression and mapping transcription factor binding sites (TFBS is key to inferring transcription factor regulatory networks. Several methods for predicting TFBS exist, but there are no standard genome-wide datasets on which to assess the performance of these prediction methods. Also, it is believed that information about sequence conservation across different genomes can generally improve accuracy of motif-based predictors, but it is not clear under what circumstances use of conservation is most beneficial. RESULTS: Here we use published ChIP-seq data and an improved peak detection method to create comprehensive benchmark datasets for prediction methods which use known descriptors or binding motifs to detect TFBS in genomic sequences. We use this benchmark to assess the performance of five different prediction methods and find that the methods that use information about sequence conservation generally perform better than simpler motif-scanning methods. The difference is greater on high-affinity peaks and when using short and information-poor motifs. However, if the motifs are specific and information-rich, we find that simple motif-scanning methods can perform better than conservation-based methods. CONCLUSIONS: Our benchmark provides a comprehensive test that can be used to rank the relative performance of transcription factor binding site prediction methods. Moreover, our results show that, contrary to previous reports, sequence conservation is better suited for predicting strong than weak transcription factor binding sites.

Pipeline for Efficient Mapping of Transcription Factor Binding Sites and Comparison of Their Models

KAUST Repository

Ba alawi, Wail

2011-06-01

The control of genes in every living organism is based on activities of transcription factor (TF) proteins. These TFs interact with DNA by binding to the TF binding sites (TFBSs) and in that way create conditions for the genes to activate. Of the approximately 1500 TFs in human, TFBSs are experimentally derived only for less than 300 TFs and only in generally limited portions of the genome. To be able to associate TF to genes they control we need to know if TFs will have a potential to interact with the control region of the gene. For this we need to have models of TFBS families. The existing models are not sufficiently accurate or they are too complex for use by ordinary biologists. To remove some of the deficiencies of these models, in this study we developed a pipeline through which we achieved the following: 1. Through a comparison analysis of the performance we identified the best models with optimized thresholds among the four different types of models of TFBS families. 2. Using the best models we mapped TFBSs to the human genome in an efficient way. The study shows that a new scoring function used with TFBS models based on the position weight matrix of dinucleotides with remote dependency results in better accuracy than the other three types of the TFBS models. The speed of mapping has been improved by developing a parallelized code and shows a significant speed up of 4x when going from 1 CPU to 8 CPUs. To verify if the predicted TFBSs are more accurate than what can be expected with the conventional models, we identified the most frequent pairs of TFBSs (for TFs E4F1 and ATF6) that appeared close to each other (within the distance of 200 nucleotides) over the human genome. We show unexpectedly that the genes that are most close to the multiple pairs of E4F1/ATF6 binding sites have a co-expression of over 90%. This indirectly supports our hypothesis that the TFBS models we use are more accurate and also suggests that the E4F1/ATF6 pair is exerting the

Mapping the active site of vaccinia virus RNA triphosphatase

International Nuclear Information System (INIS)

Gong Chunling; Shuman, Stewart

2003-01-01

The RNA triphosphatase component of vaccinia virus mRNA capping enzyme (the product of the viral D1 gene) belongs to a family of metal-dependent phosphohydrolases that includes the RNA triphosphatases of fungi, protozoa, Chlorella virus, and baculoviruses. The family is defined by two glutamate-containing motifs (A and C) that form the metal-binding site. Most of the family members resemble the fungal and Chlorella virus enzymes, which have a complex active site located within the hydrophilic interior of a topologically closed eight-stranded β barrel (the so-called ''triphosphate tunnel''). Here we queried whether vaccinia virus capping enzyme is a member of the tunnel subfamily, via mutational mapping of amino acids required for vaccinia triphosphatase activity. We identified four new essential side chains in vaccinia D1 via alanine scanning and illuminated structure-activity relationships by conservative substitutions. Our results, together with previous mutational data, highlight a constellation of six acidic and three basic amino acids that likely compose the vaccinia triphosphatase active site (Glu37, Glu39, Arg77, Lys107, Glu126, Asp159, Lys161, Glu192, and Glu194). These nine essential residues are conserved in all vertebrate and invertebrate poxvirus RNA capping enzymes. We discerned no pattern of clustering of the catalytic residues of the poxvirus triphosphatase that would suggest structural similarity to the tunnel proteins (exclusive of motifs A and C). We infer that the poxvirus triphosphatases are a distinct lineage within the metal-dependent RNA triphosphatase family. Their unique active site, which is completely different from that of the host cell's capping enzyme, recommends the poxvirus RNA triphosphatase as a molecular target for antipoxviral drug discovery

Comparison of canine parvovirus with mink enteritis virus by restriction site mapping.

OpenAIRE

McMaster, G K; Tratschin, J D; Siegl, G

1981-01-01

The genomes of canine parvovirus and mink enteritis virus were compared by restriction enzyme analysis of their replicative-form DNAs. Of 79 mapped sites, 68, or 86%, were found to be common for both types of DNA, indicating that canine parvovirus and mink enteritis virus are closely related viruses. Whether they evolved from a common precursor or whether canine parvovirus is derived from mink enteritis virus, however, cannot be deduced from our present data.

KEEFEKTIFAN MODEL SHOW NOT TELL DAN MIND MAP PADA PEMBELAJARAN MENULIS TEKS EKSPOSISI BERDASARKAN MINAT PESERTA DIDIK KELAS X SMK

Directory of Open Access Journals (Sweden)

Wiwit Lili Sokhipah

2015-03-01

Full Text Available Tujuan penelitian ini adalah (1 menentukan keefektifan penggunaan model show not tell pada pembelajaran keterampilan menulis teks eksposisi berdasarkan minat peserta didik SMK Kelas X, (2 menentukan keefektifan penggunaan model mind map pada pembelajaran keterampilan menulis teks eksposisi berdasarkan minat peserta didik SMK kelas X, (3 menentukan keefektifan interaksi show not tell dan mind map pada pembelajaran keterampilan menulis teks eksposisi berdasarkan minat peserta didik SMK kelas X. Penelitian ini adalah quasi experimental design (pretes-postes control group design. Dalam desain ini terdapat dua kelompok eksperimen yakni penerapan model show not tell dalam pembelajaran keterampilan menulis teks eksposisipeserta didik dengan minat tinggi dan penerapan model mind map dalam pembelajaran keterampilan menulis teks eksposisi  peserta didik dengan minat rendah. Hasil penelitian adalah (1 model show not tell efektif digunakan  dalam membelajarkan menulis teks eksposisi bagi peserta didik yang memiliki minat tinggi, (2 model mind map efektif digunakan dalam membelajarkan menulis teks eksposisi bagi peserta didik yang memiliki minat rendah, dan (3 model show not tell lebih efektif digunakan dalam membelajarkan menulis teks eksposisi bagi peserta didik yang memiliki minat tinggi, sedangkan model mind map efektif digunakan dalam membelajarkan teks eksposisi pagi peserta didik yang memiliki minat rendah.

Vs30 mapping at selected sites within the Greater Accra Metropolitan Area

Science.gov (United States)

Nortey, Grace; Armah, Thomas K.; Amponsah, Paulina

2018-06-01

A large part of Accra is underlain by a complex distribution of shallow soft soils. Within seismically active zones, these soils hold the most potential to significantly amplify seismic waves and cause severe damage, especially to structures sited on soils lacking sufficient stiffness. This paper presents preliminary site classification for the Greater Accra Metropolitan Area of Ghana (GAMA), using experimental data from two-dimensional (2-D) Multichannel Analysis of Surface Wave (MASW) technique. The dispersive characteristics of fundamental mode Rayleigh type surface waves were utilized for imaging the shallow subsurface layers (approx. up to 30 m depth) by estimating the 1D (depth) and 2D (depth and surface location) shear wave velocities at 5 selected sites. The average shear wave velocity for 30 m depth (Vs30), which is critical in evaluating the site response of the upper 30 m, was estimated and used for the preliminary site classification of the GAM area, as per NEHRP (National Earthquake Hazards Reduction Program). Based on the Vs30 values obtained in the study, two common site types C, and D corresponding to shallow (>6 m Lower velocity profiles are inferred for the residual soils (sandy to silty clays), derived from the Accraian Formation that lies mainly within Accra central. Stiffer soil sites lie to the north of Accra, and to the west near Nyanyano. The seismic response characteristics over the residual soils in the GAMA have become apparent using the MASW technique. An extensive site effect map and a more robust probabilistic seismic hazard analysis can now be efficiently built for the metropolis, by considering the site classes and design parameters obtained from this study.

Site-conditions map for Portugal based on VS measurements: methodology and final model

Science.gov (United States)

Vilanova, Susana; Narciso, João; Carvalho, João; Lopes, Isabel; Quinta Ferreira, Mario; Moura, Rui; Borges, José; Nemser, Eliza; Pinto, carlos

2017-04-01

In this paper we present a statistically significant site-condition model for Portugal based on shear-wave velocity (VS) data and surface geology. We also evaluate the performance of commonly used Vs30 proxies based on exogenous data and analyze the implications of using those proxies for calculating site amplification in seismic hazard assessment. The dataset contains 161 Vs profiles acquired in Portugal in the context of research projects, technical reports, academic thesis and academic papers. The methodologies involved in characterizing the Vs structure at the sites in the database include seismic refraction, multichannel analysis of seismic waves and refraction microtremor. Invasive measurements were performed in selected locations in order to compare the Vs profiles obtained from both invasive and non-invasive techniques. In general there was good agreement in the subsurface structure of Vs30 obtained from the different methodologies. The database flat-file includes information on Vs30, surface geology at 1:50.000 and 1:500.000 scales, elevation and topographic slope and based on SRTM30 topographic dataset. The procedure used to develop the site-conditions map is based on a three-step process that includes defining a preliminary set of geological units based on the literature, performing statistical tests to assess whether or not the differences in the distributions of Vs30 are statistically significant, and merging of the geological units accordingly. The dataset was, to some extent, affected by clustering and/or preferential sampling and therefore a declustering algorithm was applied. The final model includes three geological units: 1) Igneous, metamorphic and old (Paleogene and Mesozoic) sedimentary rocks; 2) Neogene and Pleistocene formations, and 3) Holocene formations. The evaluation of proxies indicates that although geological analogues and topographic slope are in general unbiased, the latter shows significant bias for particular geological units and

Map showing areas of visible land disturbances caused by two military training operations in the Mojave Desert, California

Science.gov (United States)

Prose, D.V.

1986-01-01

This map shows areas that retain visible land disturbances produced during two military armored-vehicle training operations in the Mojave Desert, California. The map documents the lasting visual effects these operations have on this arid region and provides a data base for monitoring changes in the extent of visual disturbances in the future.

Quantitative susceptibility mapping of human brain at 3T: a multisite reproducibility study.

Science.gov (United States)

Lin, P-Y; Chao, T-C; Wu, M-L

2015-03-01

Quantitative susceptibility mapping of the human brain has demonstrated strong potential in examining iron deposition, which may help in investigating possible brain pathology. This study assesses the reproducibility of quantitative susceptibility mapping across different imaging sites. In this study, the susceptibility values of 5 regions of interest in the human brain were measured on 9 healthy subjects following calibration by using phantom experiments. Each of the subjects was imaged 5 times on 1 scanner with the same procedure repeated on 3 different 3T systems so that both within-site and cross-site quantitative susceptibility mapping precision levels could be assessed. Two quantitative susceptibility mapping algorithms, similar in principle, one by using iterative regularization (iterative quantitative susceptibility mapping) and the other with analytic optimal solutions (deterministic quantitative susceptibility mapping), were implemented, and their performances were compared. Results show that while deterministic quantitative susceptibility mapping had nearly 700 times faster computation speed, residual streaking artifacts seem to be more prominent compared with iterative quantitative susceptibility mapping. With quantitative susceptibility mapping, the putamen, globus pallidus, and caudate nucleus showed smaller imprecision on the order of 0.005 ppm, whereas the red nucleus and substantia nigra, closer to the skull base, had a somewhat larger imprecision of approximately 0.01 ppm. Cross-site errors were not significantly larger than within-site errors. Possible sources of estimation errors are discussed. The reproducibility of quantitative susceptibility mapping in the human brain in vivo is regionally dependent, and the precision levels achieved with quantitative susceptibility mapping should allow longitudinal and multisite studies such as aging-related changes in brain tissue magnetic susceptibility. © 2015 by American Journal of Neuroradiology.

Covariance of biophysical data with digital topograpic and land use maps over the FIFE site

Science.gov (United States)

Davis, F. W.; Schimel, D. S.; Friedl, M. A.; Michaelsen, J. C.; Kittel, T. G. F.; Dubayah, R.; Dozier, J.

1992-01-01

This paper discusses the biophysical stratification of the FIFE site, implementation of the stratification utilizing geographic information system methods, and validation of the stratification with respect to field measurements of biomass, Bowen ratio, soil moisture, and the greenness vegetation index (GVI) derived from TM satellite data. Maps of burning and topographic position were significantly associated with variation in GVI, biomass, and Bowen ratio. The stratified design did not significantly alter the estimated site-wide means for surface climate parameters but accounted for between 25 and 45 percent of the sample variance depending on the variable.

VS30 – A site-characterization parameter for use in building Codes, simplified earthquake resistant design, GMPEs, and ShakeMaps

Science.gov (United States)

Borcherdt, Roger D.

2012-01-01

VS30, defined as the average seismic shear-wave velocity from the surface to a depth of 30 meters, has found wide-spread use as a parameter to characterize site response for simplified earthquake resistant design as implemented in building codes worldwide. VS30 , as initially introduced by the author for the US 1994 NEHRP Building Code, provides unambiguous definitions of site classes and site coefficients for site-dependent response spectra based on correlations derived from extensive borehole logging and comparative ground-motion measurement programs in California. Subsequent use of VS30 for development of strong ground motion prediction equations (GMPEs) and measurement of extensive sets of VS borehole data have confirmed the previous empirical correlations and established correlations of SVS30 with VSZ at other depths. These correlations provide closed form expressions to predict S30 V at a large number of additional sites and further justify S30 V as a parameter to characterize site response for simplified building codes, GMPEs, ShakeMap, and seismic hazard mapping.

Challenges of using an AUV to find and map hydrothermal vent sites in deep and rugged terrains

OpenAIRE

McPhail, S.D.; Stevenson, P.; Pebody, M.; Furlong, M.; Perrett, J.; LeBas, T.

2010-01-01

In March 2010, the Autosub6000 AUV embarked on a cruise to discover, locate and map hydrothermal vent sites in an active spreading centre, the Cayman trough in the Caribbean sea. The environment provided the challenge of steep and rugged terrain together with deep water (in places greater than 5000 m). Autosub6000 is a flight class, hydrodynamically shaped AUV, with good endurance capability, making it well suited for searching for plume signals and mapping terrain over the required ...

Photoaffinity labeling with cholesterol analogues precisely maps a cholesterol-binding site in voltage-dependent anion channel-1.

Science.gov (United States)

Budelier, Melissa M; Cheng, Wayland W L; Bergdoll, Lucie; Chen, Zi-Wei; Janetka, James W; Abramson, Jeff; Krishnan, Kathiresan; Mydock-McGrane, Laurel; Covey, Douglas F; Whitelegge, Julian P; Evers, Alex S

2017-06-02

Voltage-dependent anion channel-1 (VDAC1) is a highly regulated β-barrel membrane protein that mediates transport of ions and metabolites between the mitochondria and cytosol of the cell. VDAC1 co-purifies with cholesterol and is functionally regulated by cholesterol, among other endogenous lipids. Molecular modeling studies based on NMR observations have suggested five cholesterol-binding sites in VDAC1, but direct experimental evidence for these sites is lacking. Here, to determine the sites of cholesterol binding, we photolabeled purified mouse VDAC1 (mVDAC1) with photoactivatable cholesterol analogues and analyzed the photolabeled sites with both top-down mass spectrometry (MS), and bottom-up MS paired with a clickable, stable isotope-labeled tag, FLI -tag. Using cholesterol analogues with a diazirine in either the 7 position of the steroid ring (LKM38) or the aliphatic tail (KK174), we mapped a binding pocket in mVDAC1 localized to Thr 83 and Glu 73 , respectively. When Glu 73 was mutated to a glutamine, KK174 no longer photolabeled this residue, but instead labeled the nearby Tyr 62 within this same binding pocket. The combination of analytical strategies employed in this work permits detailed molecular mapping of a cholesterol-binding site in a protein, including an orientation of the sterol within the site. Our work raises the interesting possibility that cholesterol-mediated regulation of VDAC1 may be facilitated through a specific binding site at the functionally important Glu 73 residue. © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.

Usability Testing Of Web Mapping Portals

Directory of Open Access Journals (Sweden)

Petr Voldán

2011-05-01

Full Text Available This study presents a usability testing as method, which can be used to improve controlling of web map sites. Study refers to the basic principles of this method and describes particular usability tests of mapping sites. In this paper are identified potential usability problems of web sites: Amapy.cz, Google maps and Mapy.cz. The usability testing was focused on problems related with user interfaces, addresses searching and route planning of the map sites.

Value of epicardial potential maps in localizing pre-excitation sites for radiofrequency ablation. A simulation study

Science.gov (United States)

Hren, Rok

1998-06-01

Using computer simulations, we systematically investigated the limitations of an inverse solution that employs the potential distribution on the epicardial surface as an equivalent source model in localizing pre-excitation sites in Wolff-Parkinson-White syndrome. A model of the human ventricular myocardium that features an anatomically accurate geometry, an intramural rotating anisotropy and a computational implementation of the excitation process based on electrotonic interactions among cells, was used to simulate body surface potential maps (BSPMs) for 35 pre-excitation sites positioned along the atrioventricular ring. Two individualized torso models were used to account for variations in torso boundaries. Epicardial potential maps (EPMs) were computed using the L-curve inverse solution. The measure for accuracy of the localization was the distance between a position of the minimum in the inverse EPMs and the actual site of pre-excitation in the ventricular model. When the volume conductor properties and lead positions of the torso were precisely known and the measurement noise was added to the simulated BSPMs, the minimum in the inverse EPMs was at 12 ms after the onset on average within cm of the pre-excitation site. When the standard torso model was used to localize the sites of onset of the pre-excitation sequence initiated in individualized male and female torso models, the mean distance between the minimum and the pre-excitation site was cm for the male torso and cm for the female torso. The findings of our study indicate that a location of the minimum in EPMs computed using the inverse solution can offer non-invasive means for pre-interventional planning of the ablative treatment.

Land suitability maps for waste disposal siting

International Nuclear Information System (INIS)

Hrasna, M.

1996-01-01

The suitability of geoenvironment for waste disposal depends mainly on its stability and on the danger of groundwater pollution. Besides them, on the land suitability maps for the given purpose also those factors of the factors of the geoenvironment and the landscape should be taken into account, which enable another way of the land use, such as mineral resources, water resources, fertile soils, nature reserves, etc. On the base of the relevant factors influence evaluation - suitable, moderately suitable and unsuitable territorial units are delimited on the maps. The different way of various scale maps compilation is applied, taken into account their different representing feasibilities. (authors)

Harmonization of multi-site diffusion tensor imaging data.

Science.gov (United States)

Fortin, Jean-Philippe; Parker, Drew; Tunç, Birkan; Watanabe, Takanori; Elliott, Mark A; Ruparel, Kosha; Roalf, David R; Satterthwaite, Theodore D; Gur, Ruben C; Gur, Raquel E; Schultz, Robert T; Verma, Ragini; Shinohara, Russell T

2017-11-01

Diffusion tensor imaging (DTI) is a well-established magnetic resonance imaging (MRI) technique used for studying microstructural changes in the white matter. As with many other imaging modalities, DTI images suffer from technical between-scanner variation that hinders comparisons of images across imaging sites, scanners and over time. Using fractional anisotropy (FA) and mean diffusivity (MD) maps of 205 healthy participants acquired on two different scanners, we show that the DTI measurements are highly site-specific, highlighting the need of correcting for site effects before performing downstream statistical analyses. We first show evidence that combining DTI data from multiple sites, without harmonization, may be counter-productive and negatively impacts the inference. Then, we propose and compare several harmonization approaches for DTI data, and show that ComBat, a popular batch-effect correction tool used in genomics, performs best at modeling and removing the unwanted inter-site variability in FA and MD maps. Using age as a biological phenotype of interest, we show that ComBat both preserves biological variability and removes the unwanted variation introduced by site. Finally, we assess the different harmonization methods in the presence of different levels of confounding between site and age, in addition to test robustness to small sample size studies. Copyright © 2017 Elsevier Inc. All rights reserved.

Lunar Map Catalog

Data.gov (United States)

National Aeronautics and Space Administration — The Lunar Map Catalog includes various maps of the moon's surface, including Apollo landing sites; earthside, farside, and polar charts; photography index maps; zone...

Optimizing Travel Time to Outpatient Interventional Radiology Procedures in a Multi-Site Hospital System Using a Google Maps Application.

Science.gov (United States)

Mandel, Jacob E; Morel-Ovalle, Louis; Boas, Franz E; Ziv, Etay; Yarmohammadi, Hooman; Deipolyi, Amy; Mohabir, Heeralall R; Erinjeri, Joseph P

2018-02-20

The purpose of this study is to determine whether a custom Google Maps application can optimize site selection when scheduling outpatient interventional radiology (IR) procedures within a multi-site hospital system. The Google Maps for Business Application Programming Interface (API) was used to develop an internal web application that uses real-time traffic data to determine estimated travel time (ETT; minutes) and estimated travel distance (ETD; miles) from a patient's home to each a nearby IR facility in our hospital system. Hypothetical patient home addresses based on the 33 cities comprising our institution's catchment area were used to determine the optimal IR site for hypothetical patients traveling from each city based on real-time traffic conditions. For 10/33 (30%) cities, there was discordance between the optimal IR site based on ETT and the optimal IR site based on ETD at non-rush hour time or rush hour time. By choosing to travel to an IR site based on ETT rather than ETD, patients from discordant cities were predicted to save an average of 7.29 min during non-rush hour (p = 0.03), and 28.80 min during rush hour (p travel time when more than one location providing IR procedures is available within the same hospital system.

Application of time domain induced polarization to the mapping of lithotypes in a landfill site

Directory of Open Access Journals (Sweden)

A. Gazoty

2012-06-01

Full Text Available A direct current (DC resistivity and time domain induced polarization (TDIP survey was undertaken at a decommissioned landfill site situated in Hørløkke, Denmark, for the purpose of mapping the waste deposits and to discriminate important geological units that control the hydrology of the surrounding area. It is known that both waste deposits and clay have clear signatures in TDIP data, making it possible to enhance the resolution of geological structures compared to DC surveys alone.

Four DC/TDIP profiles were carried out crossing the landfill, and another seven profiles in the surroundings provide a sufficiently dense coverage of the entire area. The whole dataset was inverted using a 1-D laterally constrained inversion scheme, recently implemented for TDIP data, in order to use the entire decay curves for reconstructing the electrical parameters of the soil in terms of the Cole-Cole polarization model.

Results show that it is possible to resolve both the geometry of the buried waste body and key geological structures. In particular, it was possible to find a silt/clay lens at depth that correlates with the flow direction of the pollution plume spreading out from the landfill and to map a shallow sandy layer rich in clay that likely has a strong influence on the hydrology of the site. This interpretation of the geophysical findings was constrained by borehole data, in terms of geology and gamma ray logging. The results of this study are important for the impact of the resolved geological units on the hydrology of the area, making it possible to construct more realistic scenarios of the variation of the pollution plume as a function of the climate change.

Towards a risk map of malaria for Sri Lanka: the importance of house location relative to vector breeding sites

DEFF Research Database (Denmark)

Van Der Hoek, Wim; Konradsen, Flemming; Amerasinghe, Priyanie H

2003-01-01

of house location relative to vector breeding sites for the occurrence of malaria in order to assess the usefulness of this parameter in future malaria risk maps. Such risk maps could be important tools for planning efficient malaria control measures. METHODS: In a group of seven villages in north central......BACKGROUND: In Sri Lanka, the major malaria vector Anopheles culicifacies breeds in pools formed in streams and river beds and it is likely that people living close to such breeding sites are at higher risk of malaria than people living further away. This study was done to quantify the importance...... Sri Lanka, malaria cases were compared with community controls for distance from house to breeding sites and a number of other variables, including type of housing construction and use of anti-mosquito measures. The presence of An. culicifacies in bedrooms was determined by indoor insecticide spray...

Shear-wave velocity characterization of the USGS Hawaiian strong-motion network on the Island of Hawaii and development of an NEHRP site-class map

Science.gov (United States)

Wong, Ivan G.; Stokoe, Kenneth; Cox, Brady R.; Yuan, Jiabei; Knudsen, Keith L.; Terra, Fabia; Okubo, Paul G.; Lin, Yin-Cheng

2011-01-01

To assess the level and nature of ground shaking in Hawaii for the purposes of earthquake hazard mitigation and seismic design, empirical ground-motion prediction models are desired. To develop such empirical relationships, knowledge of the subsurface site conditions beneath strong-motion stations is critical. Thus, as a first step to develop ground-motion prediction models for Hawaii, spectral-analysis-of-surface-waves (SASW) profiling was performed at the 22 free-field U.S. Geological Survey (USGS) strong-motion sites on the Big Island to obtain shear-wave velocity (VS) data. Nineteen of these stations recorded the 2006 Kiholo Bay moment magnitude (M) 6.7 earthquake, and 17 stations recorded the triggered M 6.0 Mahukona earthquake. VS profiling was performed to reach depths of more than 100 ft. Most of the USGS stations are situated on sites underlain by basalt, based on surficial geologic maps. However, the sites have varying degrees of weathering and soil development. The remaining strong-motion stations are located on alluvium or volcanic ash. VS30 (average VS in the top 30 m) values for the stations on basalt ranged from 906 to 1908 ft/s [National Earthquake Hazards Reduction Program (NEHRP) site classes C and D], because most sites were covered with soil of variable thickness. Based on these data, an NEHRP site-class map was developed for the Big Island. These new VS data will be a significant input into an update of the USGS statewide hazard maps and to the operation of ShakeMap on the island of Hawaii.

Comparison of RS/GIS analysis with classic mapping approaches for siting low-yield boreholes for hand pumps in crystalline terrains. An application to rural communities of the Caimbambo province, Angola

Science.gov (United States)

Martín-Loeches, Miguel; Reyes-López, Jaime; Ramírez-Hernández, Jorge; Temiño-Vela, Javier; Martínez-Santos, Pedro

2018-02-01

In poverty-stricken regions of Sub-Saharan Africa, groundwater for supply is often obtained by means of hand pumps, which means that low-yield boreholes are acceptable. However, boreholes are often sited without sufficient hydrogeological information due to budget constraints, which leads to high failure rates. Cost-effective techniques for borehole siting need to be developed in order to maximize the success rate. In regions underlain by granite, weathered formations are usually targeted for drilling, as these are generally presented as a better cost-benefit ratio than the fractured basement. Within this context, this research focuses on a granite region of Angola. A comparison of two mapping techniques for borehole siting-groundwater prospect is presented. A classic hydrogeomorphological map was developed first based on aerial photographs, field mapping and a geophysical survey. This map represents a considerable time investment and was developed by qualified technicians. The second map (RS/GIS) is considerably simpler and more cost-effective. It was developed by the integration in a GIS platform of six maps of equal importance-slope, drainage density, vegetation vigor, presence of clay in the soil, lineaments and rock outcrops-prepared from Landsat 8 imagery and a Digital Elevation Model (DEM). Similar results were obtained in both cases. By means of a supervised classification of Landsat images, RS/GIS analysis allows for the identification of granitic outcrops, house clusters and sandy alluvial valleys. This in turn allows for the delineation of low-interest or contamination-prone areas, thus contributing additional qualitative information. The position of a well that is going to be powered by a handpump is chosen also upon social and local matters as the distance to the stakeholders, information that are not difficult to integrate in the GIS. Although the second map needs some field inputs (i.e. surveys to determine the thickness of the weathered pack

Archaeological Excavation and Deep Mapping in Historic Rural Communities

Directory of Open Access Journals (Sweden)

Carenza Lewis

2015-09-01

Full Text Available This paper reviews the results of more than a hundred small archaeological “test pit” excavations carried out in 2013 within four rural communities in eastern England. Each excavation used standardized protocols in a different location within the host village, with the finds dated and mapped to create a series of maps spanning more than 3500 years, in order to advance understanding of the spatial development of settlements and landscapes over time. The excavations were all carried out by local volunteers working physically within their own communities, supported and advised by professional archaeologists, with most test pits sited in volunteers’ own gardens or those of their friends, family or neighbors. Site-by-site, the results provided glimpses of the use made by humans of each of the excavated sites spanning prehistory to the present day; while in aggregate the mapped data show how settlement and land-use developed and changed over time. Feedback from participants also demonstrates the diverse positive impacts the project had on individuals and communities. The results are presented and reviewed here in order to highlight the contribution archaeological test pit excavation can make to deep mapping, and the contribution that deep mapping can make to rural communities.

Female site-specific transposase-induced recombination: a high-efficiency method for fine mapping mutations on the X chromosome in Drosophila.

OpenAIRE

Marcus, Jeffrey M

2003-01-01

P-element transposons in the Drosophila germline mobilize only in the presence of the appropriate transposase enzyme. Sometimes, instead of mobilizing completely, P elements will undergo site-specific recombination with the homologous chromosome. Site-specific recombination is the basis for male recombination mapping, since the male germline does not normally undergo recombination. Site-specific recombination also takes place in females, but this has been difficult to study because of the obs...

Discovery and Characterization of Non-ATP Site Inhibitors of the Mitogen Activated Protein (MAP) Kinases

Energy Technology Data Exchange (ETDEWEB)

Comess, Kenneth M.; Sun, Chaohong; Abad-Zapatero, Cele; Goedken, Eric R.; Gum, Rebecca J.; Borhani, David W.; Argiriadi, Maria; Groebe, Duncan R.; Jia, Yong; Clampit, Jill E.; Haasch, Deanna L.; Smith, Harriet T.; Wang, Sanyi; Song, Danying; Coen, Michael L.; Cloutier, Timothy E.; Tang, Hua; Cheng, Xueheng; Quinn, Christopher; Liu, Bo; Xin, Zhili; Liu, Gang; Fry, Elizabeth H.; Stoll, Vincent; Ng, Teresa I.; Banach, David; Marcotte, Doug; Burns, David J.; Calderwood, David J.; Hajduk, Philip J. (Abbott)

2012-03-02

Inhibition of protein kinases has validated therapeutic utility for cancer, with at least seven kinase inhibitor drugs on the market. Protein kinase inhibition also has significant potential for a variety of other diseases, including diabetes, pain, cognition, and chronic inflammatory and immunologic diseases. However, as the vast majority of current approaches to kinase inhibition target the highly conserved ATP-binding site, the use of kinase inhibitors in treating nononcology diseases may require great selectivity for the target kinase. As protein kinases are signal transducers that are involved in binding to a variety of other proteins, targeting alternative, less conserved sites on the protein may provide an avenue for greater selectivity. Here we report an affinity-based, high-throughput screening technique that allows nonbiased interrogation of small molecule libraries for binding to all exposed sites on a protein surface. This approach was used to screen both the c-Jun N-terminal protein kinase Jnk-1 (involved in insulin signaling) and p38{alpha} (involved in the formation of TNF{alpha} and other cytokines). In addition to canonical ATP-site ligands, compounds were identified that bind to novel allosteric sites. The nature, biological relevance, and mode of binding of these ligands were extensively characterized using two-dimensional {sup 1}H/{sup 13}C NMR spectroscopy, protein X-ray crystallography, surface plasmon resonance, and direct enzymatic activity and activation cascade assays. Jnk-1 and p38{alpha} both belong to the MAP kinase family, and the allosteric ligands for both targets bind similarly on a ledge of the protein surface exposed by the MAP insertion present in the CMGC family of protein kinases and distant from the active site. Medicinal chemistry studies resulted in an improved Jnk-1 ligand able to increase adiponectin secretion in human adipocytes and increase insulin-induced protein kinase PKB phosphorylation in human hepatocytes, in

MAPS of Cancer

Science.gov (United States)

Gray, Lincoln

1998-01-01

to show meaningful patterns of dispersal. We had previously published the functional map of the head and neck, but it was difficult to explain to either patients or surgeons because that view of our body did not resemble anatomy. This discrepancy between functional and physical maps is just a mathematical restatement of the well-known fact that some diseases, such as head and neck cancer, spread in complex patterns, not always to the next nearest site. We had discovered that a computer could re-arrange anatomy so that this particular disease spreads to the next nearest site. The functional map explains over 95% of the metastases in 1400 patients. In a sense, we had graphed what our body "looks like" to a tumor. The tumor readily travels between adjacent areas in the functional map. The functional map is a succinct visual display of trends that are not easily appreciated in tables of probabilities.

Radioactivity. To better manage polluted soils and sites. Pargny-sur-Saulx, more than 15 years of interventions. Chef de Baie, radioactivity mapping

International Nuclear Information System (INIS)

Caplin, Helene; Baumont, Genevieve; Tardieu, Laure; Brisson, Nicolas; Guillevic, Jerome; Serres, Christophe; Barrieu, Olivier

2016-01-01

A set of articles proposes an overview of the various actions performed by the IRSN for the management of sites and soils polluted by radioactive substances. A first article outlines the need for a national strategy to manage about forty polluted sites, the lack of a waste elimination sector (the storage is organised, but not the elimination), the action of the IRSN in mapping the radioactivity, in assessing the associated exposure, and in supporting decontamination actions. Costs, benefits, risks and actors are also evoked. A second article describes the various interventions organised over 15 years to manage a site which had been contaminated by the thorium from an ancient plant: site safety, interviews of personnel, elimination of all significant radioactivity. The last article addresses the case of another site, Chef de Baie in La Rochelle, which had been used as a deposit for contaminated materials produced by a neighbouring plant, and where the IRSN intervened to map the radioactivity

Mapping the Binding Site for Escitalopram and Paroxetine in the Human Serotonin Transporter Using Genetically Encoded Photo-Cross-Linkers

DEFF Research Database (Denmark)

Rannversson, Hafsteinn; Andersen, Jacob; Bang-Andersen, Benny

2017-01-01

amber codon suppression in hSERT to encode the photo-cross-linking unnatural amino acid p-azido-l-phenylalanine into the suggested high- and low-affinity binding sites. We then employ UV-induced cross-linking with azF to map the binding site of escitalopram and paroxetine, two prototypical selective...... serotonin reuptake inhibitors (SSRIs). We find that the two antidepressant drugs exclusively cross-link to azF incorporated at the high-affinity binding site of hSERT, while cross-linking is not observed at the low-affinity binding site. Combined with previous homology models and recent structural data on h...

Sonic Fiction as the Mapping of Difference

DEFF Research Database (Denmark)

Holmboe, Rasmus; Stricker, Jan Høgh

2015-01-01

The here proposed audio paper/audio lecture performance is an iteration of a site-specific participatory performance piece by Danish artist, composer and musician, Andreas Führer. The piece, which has the title THE MAP IS NOT THE TERRITORY D’OR, is a scored sound walk, which shows a map designati......) as a discussion and contextualisation of sonic materialist (Cox, 2011) and signifying representationalist (Kim-Cohen, 2009) positions....

Probability mapping of contaminants

International Nuclear Information System (INIS)

Rautman, C.A.; Kaplan, P.G.; McGraw, M.A.; Istok, J.D.; Sigda, J.M.

1994-01-01

Exhaustive characterization of a contaminated site is a physical and practical impossibility. Descriptions of the nature, extent, and level of contamination, as well as decisions regarding proposed remediation activities, must be made in a state of uncertainty based upon limited physical sampling. The probability mapping approach illustrated in this paper appears to offer site operators a reasonable, quantitative methodology for many environmental remediation decisions and allows evaluation of the risk associated with those decisions. For example, output from this approach can be used in quantitative, cost-based decision models for evaluating possible site characterization and/or remediation plans, resulting in selection of the risk-adjusted, least-cost alternative. The methodology is completely general, and the techniques are applicable to a wide variety of environmental restoration projects. The probability-mapping approach is illustrated by application to a contaminated site at the former DOE Feed Materials Production Center near Fernald, Ohio. Soil geochemical data, collected as part of the Uranium-in-Soils Integrated Demonstration Project, have been used to construct a number of geostatistical simulations of potential contamination for parcels approximately the size of a selective remediation unit (the 3-m width of a bulldozer blade). Each such simulation accurately reflects the actual measured sample values, and reproduces the univariate statistics and spatial character of the extant data. Post-processing of a large number of these equally likely statistically similar images produces maps directly showing the probability of exceeding specified levels of contamination (potential clean-up or personnel-hazard thresholds)

Probability mapping of contaminants

Energy Technology Data Exchange (ETDEWEB)

Rautman, C.A.; Kaplan, P.G. [Sandia National Labs., Albuquerque, NM (United States); McGraw, M.A. [Univ. of California, Berkeley, CA (United States); Istok, J.D. [Oregon State Univ., Corvallis, OR (United States); Sigda, J.M. [New Mexico Inst. of Mining and Technology, Socorro, NM (United States)

1994-04-01

Exhaustive characterization of a contaminated site is a physical and practical impossibility. Descriptions of the nature, extent, and level of contamination, as well as decisions regarding proposed remediation activities, must be made in a state of uncertainty based upon limited physical sampling. The probability mapping approach illustrated in this paper appears to offer site operators a reasonable, quantitative methodology for many environmental remediation decisions and allows evaluation of the risk associated with those decisions. For example, output from this approach can be used in quantitative, cost-based decision models for evaluating possible site characterization and/or remediation plans, resulting in selection of the risk-adjusted, least-cost alternative. The methodology is completely general, and the techniques are applicable to a wide variety of environmental restoration projects. The probability-mapping approach is illustrated by application to a contaminated site at the former DOE Feed Materials Production Center near Fernald, Ohio. Soil geochemical data, collected as part of the Uranium-in-Soils Integrated Demonstration Project, have been used to construct a number of geostatistical simulations of potential contamination for parcels approximately the size of a selective remediation unit (the 3-m width of a bulldozer blade). Each such simulation accurately reflects the actual measured sample values, and reproduces the univariate statistics and spatial character of the extant data. Post-processing of a large number of these equally likely statistically similar images produces maps directly showing the probability of exceeding specified levels of contamination (potential clean-up or personnel-hazard thresholds).

Fusion of protegrin-1 and plectasin to MAP30 shows significant inhibition activity against dengue virus replication.

Directory of Open Access Journals (Sweden)

Hussin A Rothan

Full Text Available Dengue virus (DENV broadly disseminates in tropical and sub-tropical countries and there are no vaccine or anti-dengue drugs available. DENV outbreaks cause serious economic burden due to infection complications that requires special medical care and hospitalization. This study presents a new strategy for inexpensive production of anti-DENV peptide-fusion protein to prevent and/or treat DENV infection. Antiviral cationic peptides protegrin-1 (PG1 and plectasin (PLSN were fused with MAP30 protein to produce recombinant antiviral peptide-fusion protein (PG1-MAP30-PLSN as inclusion bodies in E. coli. High yield production of PG1-MAP30-PLSN protein was achieved by solubilization of inclusion bodies in alkaline buffer followed by the application of appropriate refolding techniques. Antiviral PG1-MAP30-PLSN protein considerably inhibited DENV protease (NS2B-NS3pro with half-maximal inhibitory concentration (IC50 0.5±0.1 μM. The real-time proliferation assay (RTCA and the end-point proliferation assay (MTT assay showed that the maximal-nontoxic dose of the peptide-fusion protein against Vero cells is approximately 0.67±0.2 μM. The cell-based assays showed considerable inhibition of the peptide-fusion protein against binding and proliferating stages of DENV2 into the target cells. The peptide-fusion protein protected DENV2-challeged mice with 100% of survival at the dose of 50 mg/kg. In conclusion, producing recombinant antiviral peptide-fusion protein by combining short antiviral peptide with a central protein owning similar activity could be useful to minimize the overall cost of short peptide production and take advantage of its synergistic antiviral activities.

Isthmus sites identified by Ripple Mapping are usually anatomically stable: A novel method to guide atrial substrate ablation?

Science.gov (United States)

Luther, Vishal; Qureshi, Norman; Lim, Phang Boon; Koa-Wing, Michael; Jamil-Copley, Shahnaz; Ng, Fu Siong; Whinnett, Zachary; Davies, D Wyn; Peters, Nicholas S; Kanagaratnam, Prapa; Linton, Nick

2018-03-01

Postablation reentrant ATs depend upon conducting isthmuses bordered by scar. Bipolar voltage maps highlight scar as sites of low voltage, but the voltage amplitude of an electrogram depends upon the myocardial activation sequence. Furthermore, a voltage threshold that defines atrial scar is unknown. We used Ripple Mapping (RM) to test whether these isthmuses were anatomically fixed between different activation vectors and atrial rates. We studied post-AF ablation ATs where >1 rhythm was mapped. Multipolar catheters were used with CARTO Confidense for high-density mapping. RM visualized the pattern of activation, and the voltage threshold below which no activation was seen. Isthmuses were characterized at this threshold between maps for each patient. Ten patients were studied (Map 1 was AT1; Map 2: sinus 1/10, LA paced 2/10, AT2 with reverse CS activation 3/10; AT2 CL difference 50 ± 30 ms). Point density was similar between maps (Map 1: 2,589 ± 1,330; Map 2: 2,214 ± 1,384; P  =  0.31). RM activation threshold was 0.16 ± 0.08 mV. Thirty-one isthmuses were identified in Map 1 (median 3 per map; width 27 ± 15 mm; 7 anterior; 6 roof; 8 mitral; 9 septal; 1 posterior). Importantly, 7 of 31 (23%) isthmuses were unexpectedly identified within regions without prior ablation. AT1 was treated following ablation of 11/31 (35%) isthmuses. Of the remaining 20 isthmuses, 14 of 16 isthmuses (88%) were consistent between the two maps (four were inadequately mapped). Wavefront collision caused variation in low voltage distribution in 2 of 16 (12%). The distribution of isthmuses and nonconducting tissue within the ablated left atrium, as defined by RM, appear concordant between rhythms. This could guide a substrate ablative approach. © 2018 Wiley Periodicals, Inc.

Preliminary soil-slip susceptibility maps, southwestern California

Science.gov (United States)

Morton, Douglas M.; Alvarez, Rachel M.; Campbell, Russell H.; Digital preparation by Bovard, Kelly R.; Brown, D.T.; Corriea, K.M.; Lesser, J.N.

2003-01-01

This group of maps shows relative susceptibility of hill slopes to the initiation sites of rainfall-triggered soil slip-debris flows in southwestern California. As such, the maps offer a partial answer to one part of the three parts necessary to predict the soil-slip/debris-flow process. A complete prediction of the process would include assessments of “where”, “when”, and “how big”. These maps empirically show part of the “where” of prediction (i.e., relative susceptibility to sites of initiation of the soil slips) but do not attempt to show the extent of run out of the resultant debris flows. Some information pertinent to “when” the process might begin is developed. “When” is determined mostly by dynamic factors such as rainfall rate and duration, for which local variations are not amenable to long-term prediction. “When” information is not provided on the maps but is described later in this narrative. The prediction of “how big” is addressed indirectly by restricting the maps to a single type of landslide process—soil slip-debris flows. The susceptibility maps were created through an iterative process from two kinds of information. First, locations of sites of past soil slips were obtained from inventory maps of past events. Aerial photographs, taken during six rainy seasons that produced abundant soil slips, were used as the basis for soil slip-debris flow inventory. Second, digital elevation models (DEM) of the areas that were inventoried were used to analyze the spatial characteristics of soil slip locations. These data were supplemented by observations made on the ground. Certain physical attributes of the locations of the soil-slip debris flows were found to be important and others were not. The most important attribute was the mapped bedrock formation at the site of initiation of the soil slip. However, because the soil slips occur in surficial materials overlying the bedrocks units, the bedrock formation can only serve as

Mapping of impediments to contamination flow using multicomponent reflection seismology at the Savannah River Site

International Nuclear Information System (INIS)

Dickenson, O.A.; Steensma, G.J.; Boyd, T.M.

1996-01-01

A major obstacle to the remediation of contaminated aquifers at the Savannah River Site in Aiken, South Carolina is the presence of discontinuous sand and clay lenses that are difficult to map effectively using geologic and geophysical well logs. In order to map these discontinuous sand and clay lenses we acquire two perpendicular nine-component (9C) seismic lines, a 9C Vertical Seismic Profile, (VSP) and p-wave and s-wave sonic logs in a borehole south of the Old Burial Ground at the Savannah River Site within which were available natural gamma ray and interpreted geology logs. P-wave reflections are interpreted as originating from water table, the Tan Clay, the Green Clay, the top of the Ellenton Clay, and a calcareous sediment layer within the Barnwell/McBean aquifer. Along the east-west trending line, reflectors are generally continuous except for the occurrence of a discontinuity in the upper reflectors near the east end of the line. This discontinuity could be interpreted as a sediment slump feature possibly related to the dissolution of the calcareous sediment layer, or as the eastern terminus of a large scour feature. Along the north-south trending line, reflectors are spatially less continuous and are interpreted as being cut by several channel/scour features

A combinatorial framework for map labeling

NARCIS (Netherlands)

Wagner, F.; Wolff, A.; Whitesides, S.

1998-01-01

The general map labeling problem consists in labeling a set of sites (points, lines, regions) given a set of candidates (rectangles, circles, ellipses, irregularly shaped labels) for each site. A map can be a classical cartographical map, a diagram, a graph or any other figure that needs to be

Oblique map showing maximum extent of 20,000-year-old (Tioga) glaciers, Yosemite National Park, central Sierra Nevada, California

Science.gov (United States)

Alpha, T.R.; Wahrhaftig, Clyde; Huber, N.K.

1987-01-01

This map shows the alpine ice field and associated valley glaciers at their maximum extent during the Tioga glaciation. The Tioga glaciation, which peaked about 15,000-20,OOO years ago, was the last major glaciation in the Sierra Nevada. The Tuolumne ice field fed not only the trunk glacier that moved down the Tuolumne River canyon through the present-day Hetch Hetchy Reservoir, but it also overflowed major ridge crests into many adjoining drainage systems. Some of the ice flowed over low passes to augment the flows moving from the Merced basin down through little Yosemite Valley. Tuolumne ice flowed southwest down the Tuolumne River into the Tenaya Lake basin and then down Tenaya Canyon to join the Merced glacier in Yosemite Valley. During the Tioga glaciation, the glacier in Yosemite Valley reached only as far as Bridalveil Meadow, although during a much earlier glaciation, a glacier extended about 10 miles farther down the Merced River to the vicinity of El Portal. Ice of the Tioga glaciation also flowed eastward from the summit region to cascade down the canyons that cut into the eastern escarpment of the Sierra Nevada [see errata, below]. Southeast of the present-day Yosemite Park, glaciers formed in the Mount Lyell region flowed east onto the Mono lowland and southeast and south down the Middle and North Forks of the San Joaquin River. In the southern part of the park, glaciers nearly reached to the present-day site of Wawona along the South Fork of the Merced River. At the time of the maximum extent of the Tioga glaciation, Lake Russell (Pleistocene Mono Lake) had a surface elevation of 6,800 feet, 425 feet higher than the 1980 elevation and 400 feet lower than its maximum level at the end of the Tioga glaciation. Only a few volcanic domes of the Mono Craters existed at the time of the Tioga glaciation. The distribution of vegetation, as suggested by the green overprint, is based on our interpretation. Forests were restricted to lower elevations than present

Landing Site Selection and Surface Traverse Planning using the Lunar Mapping & Modeling Portal

Science.gov (United States)

Law, E.; Chang, G.; Bui, B.; Sadaqathullah, S.; Kim, R.; Dodge, K.; Malhotra, S.

2013-12-01

Introduction: The Lunar Mapping and Modeling Portal (LMMP), is a web-based Portal and a suite of interactive visualization and analysis tools for users to access mapped lunar data products (including image mosaics, digital elevation models, etc.) from past and current lunar missions (e.g., Lunar Reconnaissance Orbiter, Apollo, etc.), and to perform in-depth analyses to support lunar surface mission planning and system design for future lunar exploration and science missions. It has been widely used by many scientists mission planners, as well as educators and public outreach (e.g., Google Lunar XPRICE teams, RESOLVE project, museums etc.) This year, LMMP was used by the Lunar and Planetary Institute (LPI)'s Lunar Exploration internship program to perform lighting analysis and local hazard assessments, such as, slope, surface roughness and crater/boulder distribution to research landing sites and surface pathfinding and traversal. Our talk will include an overview of LMMP, a demonstration of the tools as well as a summary of the LPI Lunar Exploration summer interns' experience in using those tools.

Digital Geologic Map of the Nevada Test Site and Vicinity, Nye, Lincoln, and Clark Counties, Nevada, and Inyo County, California

Science.gov (United States)

Slate, Janet L.; Berry, Margaret E.; Rowley, Peter D.; Fridrich, Christopher J.; Morgan, Karen S.; Workman, Jeremiah B.; Young, Owen D.; Dixon, Gary L.; Williams, Van S.; McKee, Edwin H.; Ponce, David A.; Hildenbrand, Thomas G.; Swadley, W.C.; Lundstrom, Scott C.; Ekren, E. Bartlett; Warren, Richard G.; Cole, James C.; Fleck, Robert J.; Lanphere, Marvin A.; Sawyer, David A.; Minor, Scott A.; Grunwald, Daniel J.; Laczniak, Randell J.; Menges, Christopher M.; Yount, James C.; Jayko, Angela S.

1999-01-01

This digital geologic map of the Nevada Test Site (NTS) and vicinity, as well as its accompanying digital geophysical maps, are compiled at 1:100,000 scale. The map compilation presents new polygon (geologic map unit contacts), line (fault, fold axis, metamorphic isograd, dike, and caldera wall) and point (structural attitude) vector data for the NTS and vicinity, Nye, Lincoln, and Clark Counties, Nevada, and Inyo County, California. The map area covers two 30 x 60-minute quadrangles-the Pahute Mesa quadrangle to the north and the Beatty quadrangle to the south-plus a strip of 7.5-minute quadrangles on the east side-72 quadrangles in all. In addition to the NTS, the map area includes the rest of the southwest Nevada volcanic field, part of the Walker Lane, most of the Amargosa Desert, part of the Funeral and Grapevine Mountains, some of Death Valley, and the northern Spring Mountains. This geologic map improves on previous geologic mapping of the same area (Wahl and others, 1997) by providing new and updated Quaternary and bedrock geology, new geophysical interpretations of faults beneath the basins, and improved GIS coverages. Concurrent publications to this one include a new isostatic gravity map (Ponce and others, 1999) and a new aeromagnetic map (Ponce, 1999).

Mapping of contamination at Savannah River Site FBWU by INEEL trolley

International Nuclear Information System (INIS)

Carpenter, M.V.; Gehrke, R.J.; Helmer, R.G.; Josten, N.

1998-01-01

The Ford Building Waste Unit (FBWU) 643-11G is a Resource Conservation and Recovery Act/Comprehensive Environmental Response Compensation and Liability Act (RCRA/CERCLA) designated site at the Savannah River Site (SRS) in Aiken, South Carolina. Pre-Work Plan Characterization at the FBWU in May 1996 indicated that radiological contamination was present in surface and near surface soils and identified cesium-137, 137 Cs, the unit specific contaminant, as being primarily in the top 15 cm of soil. The Idaho National Engineering and Environmental Laboratory (INEEL) sent the dig-face trolley system to SRS where it demonstrated its capability over a 6.1-m (20 ft.) x 9.6-m (30 ft.) area to rapidly map the contamination on-line with its large area plastic scintillation detector. Also, an extended-range (10 keV to 3 MeV) Ge detector was used at selected locations to identify and quantify the 137 Cs contamination. The coordinate locations of each measurement acquired in either the scanning or fixed position mode was obtained with a survey system based on radial encoders. Topography measurements were also made during measurements to permit correction of field of view and activity concentrations for changes in the ground to detector distance

Differences in fatty degeneration of rotator cuff muscles at different sites, as quantified by T2 mapping.

Science.gov (United States)

Iijima, Yuki; Matsuki, Keisuke; Hoshika, Shota; Ueda, Yusuke; Onishi, Kazutomo; Tokai, Morihito; Takahashi, Norimasa; Sugaya, Hiroyuki; Dougo, Kazuhiko; Watanabe, Atsuya

2017-03-01

Fatty degeneration of the cuff muscles is usually evaluated at the Y-view in oblique sagittal images. It was recently proposed that muscle shift after repair may influence the fatty degeneration values, and the evaluation of the muscles at a more medial site was recommended. However, the differences in muscle quality in accord with measurement sites have been unclear. Here we evaluated differences in fatty degeneration of the rotator cuff muscles measured quantitatively at different sites, using T2 mapping. We assessed 702 shoulders of 675 patients (335 males, 340 females; mean age, 62 years) who underwent MRI including T2 mapping. There were 345 shoulders without rotator cuff tears and 357 shoulders with tears: partial tear = 103 shoulders; small = 63; medium = 94; large = 71; massive = 26. T2 values of the supraspinatus and infraspinatus muscles were measured on the Y-view and on the image that was 15 mm medial to the Y-view. The T2 values at the medial site increased with the tear extent, as did those on the Y-view. There were no significant differences in supraspinatus T2 values between those on the Y-view and at the medial site in all tear size groups except medium and large tears (p = 0.008 and p tear size groups except large tears (p = 0.002). However, the differences were relatively small (2.4-5.6 ms), which were within the standard deviations of the measurements. The T2 values of the supraspinatus and infraspinatus muscles on the Y-view and at 15 mm medial to it were almost identical, with the exception of small differences in the case of larger tears. Copyright © 2016. Published by Elsevier B.V.

Application of ecological mapping

International Nuclear Information System (INIS)

Sherk, J.A.

1982-01-01

The US Fish and Wildlife Service has initiated the production of a comprehensive ecological inventory map series for use as a major new planning tool. Important species data along with special land use designations are displayed on 1:250,000 scale topographic base maps. Sets of maps have been published for the Atlantic and Pacific coastal areas of the United States. Preparation of a map set for the Gulf of Mexico is underway at the present time. Potential application of ecological inventory map series information to a typical land disposal facility could occur during the narrowing of the number of possible disposal sites, the design of potential disposal site studies of ecological resources, the preparation of the environmental report, and the regulatory review of license applications. 3 figures, 3 tables

GenMapDB: a database of mapped human BAC clones

OpenAIRE

Morley, Michael; Arcaro, Melissa; Burdick, Joshua; Yonescu, Raluca; Reid, Thomas; Kirsch, Ilan R.; Cheung, Vivian G.

2001-01-01

GenMapDB (http://genomics.med.upenn.edu/genmapdb) is a repository of human bacterial artificial chromosome (BAC) clones mapped by our laboratory to sequence-tagged site markers. Currently, GenMapDB contains over 3000 mapped clones that span 19 chromosomes, chromosomes 2, 4, 5, 9–22, X and Y. This database provides positional information about human BAC clones from the RPCI-11 human male BAC library. It also contains restriction fragment analysis data and end sequen...

Osteosarcoma: correlation of T1 map and histology map

International Nuclear Information System (INIS)

Suh, Jin Suck; Yun, Mi Jin; Jeong, Eun Kee; Shin, Kyoo Ho; Yang, Woo Ick

1999-01-01

To determine whether T1 mapping shows regional differences between viable and necrotic regions of osteosarcomas after anticancer chemotherapy and to assess whether this mapping is able to express the characteristics of various intramural tissue components. Eleven of 20 osteosarcomas were included in this study, while the remaining nine were excluded because the tumor site was inappropriate for comparison of T1 map and tumor macrosection. All patients underwent MR imaging for the purpose of T1 mapping, followed by pre-operative chemotherapy and subsequent limb-salvage surgery. Spin echo pulse sequencing was used with varying TR (100, 200, 400, 800, 1600, and 2400 msec) and a constant TE of 20 msec. Using a C-language software program, T1 relaxation time was calculated on a pixel-by-pixel basis and then a T1 map was generated by using a post-processing program, NIH Image. We attempted correlation of the T1 map and histologic findings, particularly in regions of interest(ROI) if certain areas were different from other regions on either the T1 or histologic map. Value was expressed as an average of the ratio of T1 of ROI and T1 of fat tissue, and this was used as an internal reference for normalization of the measurement. Tumor necrosis was 100 %(Grade IV) in six specimens, and over 90 % (Grade III) in five. Viable tumor cells were found mostly in regions with chondroid matrix and seldom in regions with osteoid matrix. Regardless of cell viability, values ranged from 0.9 to 9.87(mean, 4.02) in tumor necrotic area with osteoid matrices, and from 3.04 to 3.9(mean, 3.55) in areas with chondroid matrices. Other regions with fibrous tissue proliferation, hemorrhage, and fatty necrosis showed values of 2.92-9.83(mean, 7.20), 2.65-5.96(mean,3.59), and 1.43-3.11(mean, 2.68) respectively. The values of various tissues overlapped. No statistically significant difference was found between regions in which tumors were viable and those with tumor necrosis. Although we hypothesized

St. Louis area earthquake hazards mapping project; seismic and liquefaction hazard maps

Science.gov (United States)

Cramer, Chris H.; Bauer, Robert A.; Chung, Jae-won; Rogers, David; Pierce, Larry; Voigt, Vicki; Mitchell, Brad; Gaunt, David; Williams, Robert; Hoffman, David; Hempen, Gregory L.; Steckel, Phyllis; Boyd, Oliver; Watkins, Connor M.; Tucker, Kathleen; McCallister, Natasha

2016-01-01

We present probabilistic and deterministic seismic and liquefaction hazard maps for the densely populated St. Louis metropolitan area that account for the expected effects of surficial geology on earthquake ground shaking. Hazard calculations were based on a map grid of 0.005°, or about every 500 m, and are thus higher in resolution than any earlier studies. To estimate ground motions at the surface of the model (e.g., site amplification), we used a new detailed near‐surface shear‐wave velocity model in a 1D equivalent‐linear response analysis. When compared with the 2014 U.S. Geological Survey (USGS) National Seismic Hazard Model, which uses a uniform firm‐rock‐site condition, the new probabilistic seismic‐hazard estimates document much more variability. Hazard levels for upland sites (consisting of bedrock and weathered bedrock overlain by loess‐covered till and drift deposits), show up to twice the ground‐motion values for peak ground acceleration (PGA), and similar ground‐motion values for 1.0 s spectral acceleration (SA). Probabilistic ground‐motion levels for lowland alluvial floodplain sites (generally the 20–40‐m‐thick modern Mississippi and Missouri River floodplain deposits overlying bedrock) exhibit up to twice the ground‐motion levels for PGA, and up to three times the ground‐motion levels for 1.0 s SA. Liquefaction probability curves were developed from available standard penetration test data assuming typical lowland and upland water table levels. A simplified liquefaction hazard map was created from the 5%‐in‐50‐year probabilistic ground‐shaking model. The liquefaction hazard ranges from low (60% of area expected to liquefy) in the lowlands. Because many transportation routes, power and gas transmission lines, and population centers exist in or on the highly susceptible lowland alluvium, these areas in the St. Louis region are at significant potential risk from seismically induced liquefaction and associated

BAC-HAPPY mapping (BAP mapping: a new and efficient protocol for physical mapping.

Directory of Open Access Journals (Sweden)

Giang T H Vu

2010-02-01

Full Text Available Physical and linkage mapping underpin efforts to sequence and characterize the genomes of eukaryotic organisms by providing a skeleton framework for whole genome assembly. Hitherto, linkage and physical "contig" maps were generated independently prior to merging. Here, we develop a new and easy method, BAC HAPPY MAPPING (BAP mapping, that utilizes BAC library pools as a HAPPY mapping panel together with an Mbp-sized DNA panel to integrate the linkage and physical mapping efforts into one pipeline. Using Arabidopsis thaliana as an exemplar, a set of 40 Sequence Tagged Site (STS markers spanning approximately 10% of chromosome 4 were simultaneously assembled onto a BAP map compiled using both a series of BAC pools each comprising 0.7x genome coverage and dilute (0.7x genome samples of sheared genomic DNA. The resultant BAP map overcomes the need for polymorphic loci to separate genetic loci by recombination and allows physical mapping in segments of suppressed recombination that are difficult to analyze using traditional mapping techniques. Even virtual "BAC-HAPPY-mapping" to convert BAC landing data into BAC linkage contigs is possible.

Baseline mapping study of the Steed Pond aquifer and vadose zone beneath A/M Area, Savannah River Site, Aiken, South Carolina

International Nuclear Information System (INIS)

Jackson, D.G. Jr.

2000-01-01

This report presents the second phase of a baseline mapping project conducted for the Environmental Restoration Department (ERD) at Savannah River Site. The purpose of this second phase is to map the structure and distribution of mud (clay and silt-sized sediment) within the vadose zone beneath A/M Area. The results presented in this report will assist future characterization and remediation activities in the vadose zone and upper aquifer zones in A/M Area

Map showing selected surface-water data for the Alton-Kolob coal-fields area, Utah

Science.gov (United States)

Price, Don

1982-01-01

This is one of a series of maps that describe the geology and related natural resources of the Alton-Kolob coal-fields area, Utah. Streamflow records used to compile the map and the following table were collected by the U.S. Geological Survey in cooperation with the Utah Department of Natural Resources, Division of Water Rights, and the Utah Department of Transportation. The principal runoff-producing areas were delineated form a work map (scale 1:250,000) compiled to estimate water yields in Utah (Bagley and others, 1964).

Statistical analysis of results from the quantitative mapping of fracture minerals in Laxemar. Site descriptive modelling - complementary studies

Energy Technology Data Exchange (ETDEWEB)

Loefgren, Martin (Niressa AB, Norsborg (Sweden)); Sidborn, Magnus (Kemakta Konsult AB, Stockholm (Sweden))

2010-12-15

Within the Laxemar site investigation campaign, quantitative mapping of different fracture minerals has been performed. This has been done by studying fracture surfaces of drill core sections from many different boreholes at the Laxemar site /Eklund and Mattsson 2008/. The drill core mapping was focused on the rock in the vicinity of flow anomalies detected by the Posiva Flow Log (PFL). The quantitative mapping was performed only on open fractures. The fracture minerals that were mapped are calcite, chlorite, clay minerals (as a group), hematite, and pyrite. In this present report, data from the quantitative mineral mapping campaign are refined, sorted into different data subsets, and analysed by parametric and non-parametric statistical methods. The data subsets are associated with 17 different rock volumes, representing different elevations, rock domains, fracture domains, and groups of deformation zones. In total 1,852 fractures were mapped at the site, and the most frequent mineral was calcite. Its amount could be quantitatively estimated in 51% of the mapped fractures. Of the other minerals, chlorite was quantitatively estimated in 46%, pyrite in 19%, clay minerals in 16%, and hematite in 0.05% of the mapped fractures. For fractures where the averaged fracture mineral thickness, d{sub mean} [mm], and visible coverage, C{sub vis} [%], could be quantitatively estimated, the following arithmetic means were found: calcite = 0.25 mm and 22%, chlorite = 0.29 mm and 41%, pyrite =1.3 mum and 0.2%, and clay minerals = 0.15 mm and 35%. These quantities are based on visual inspection of fracture surfaces and do not include the contribution from non-consolidated fracture fillings. It is shown that there is significant spatial variability of d{sub mean} and C{sub vis} within the examined rock volumes. Furthermore, the non-parametric analyses indicate that there are differences in d{sub mean} and C{sub vis} between the different rock volumes. Even so, the differences are

Statistical analysis of results from the quantitative mapping of fracture minerals in Forsmark. Site descriptive modelling - complementary studies

Energy Technology Data Exchange (ETDEWEB)

Loefgren, Martin (Niressa AB, Norsborg (Sweden)); Sidborn, Magnus (Kemakta Konsult AB, Stockholm (Sweden))

2010-12-15

Within the Forsmark site investigation campaign, quantitative mapping of different fracture minerals has been performed. This has been done by studying fracture surfaces of drill core sections from many different boreholes at the Forsmark site /Eklund and Mattsson 2009/. The drill core mapping was focused on the rock in the vicinity of flow anomalies detected by the Posiva Flow Log (PFL). The quantitative mapping was performed only on open fractures. The fracture minerals that were mapped are calcite, chlorite, clay minerals (as a group), hematite, and pyrite. In this present report, data from the quantitative mineral mapping campaign are refined, sorted into different data subsets, and analysed by parametric and non-parametric statistical methods. The data subsets are associated with 21 different rock volumes, representing different elevations, rock domains, fracture domains, and groups of deformation zones. In total 2,071 fractures were mapped at the site, and the most frequent mineral was calcite. Its amount could be quantitatively estimated in 32% of the mapped fractures. Of the other minerals, chlorite was quantitatively estimated in 24%, clay minerals in 11%, pyrite in 10%, and hematite in 0.4% of the mapped fractures. For fractures where the averaged fracture mineral thickness, d{sub mean} [mm], and visible coverage, C{sub vis} [%], could be quantitatively estimated, the following arithmetic means were found: calcite = 0.11 mm and 18%, chlorite = 0.22 mm and 38%, clay minerals = 0.14 mm and 40%, pyrite = 2.3 mum and 0.5%, hematite = 19 mum and 14%. These quantities are based on visual inspection of fracture surfaces and do not include the contribution from non-consolidated fracture fillings. It is shown that there is significant spatial variability of d{sub mean} and C{sub vis} within the examined rock volumes. Furthermore, the non-parametric analyses indicate that there are differences in d{sub mean} and C{sub vis} between the different rock volumes. Even

Mapping of reed in shallow bays. SFR-Site Forsmark

Energy Technology Data Exchange (ETDEWEB)

Stroemgren, Maarten; Lindgren, Fredrik (Umeaa Univ. (Sweden))

2011-03-15

The regolith-lake development model (RLDM) describes the development of shallow bays to lakes and the infilling of lakes in the Forsmark area during an interglacial. The sensitivity analysis has shown the need for an update of the infill procedure in the RLDM. Data from the mapping of reed in shallow bays in the Forsmark area will be used to improve the infill procedure of an updated RLDM. The field work was performed in August 26-31, 2010. The mapping of reed was done in 124 points. In these points, coordinates and water depth were mapped using an echo sounder and a DGPS. Quaternary deposits and the thickness of soft sediments were mapped using an earth probe. Measurement points were delivered in ESRI shape format with coordinates in RT90 2.5 gon W and altitudes in the RHB70 system for storage in SKB's GIS data base

Seismic hazard maps for Haiti

Science.gov (United States)

Frankel, Arthur; Harmsen, Stephen; Mueller, Charles; Calais, Eric; Haase, Jennifer

2011-01-01

We have produced probabilistic seismic hazard maps of Haiti for peak ground acceleration and response spectral accelerations that include the hazard from the major crustal faults, subduction zones, and background earthquakes. The hazard from the Enriquillo-Plantain Garden, Septentrional, and Matheux-Neiba fault zones was estimated using fault slip rates determined from GPS measurements. The hazard from the subduction zones along the northern and southeastern coasts of Hispaniola was calculated from slip rates derived from GPS data and the overall plate motion. Hazard maps were made for a firm-rock site condition and for a grid of shallow shear-wave velocities estimated from topographic slope. The maps show substantial hazard throughout Haiti, with the highest hazard in Haiti along the Enriquillo-Plantain Garden and Septentrional fault zones. The Matheux-Neiba Fault exhibits high hazard in the maps for 2% probability of exceedance in 50 years, although its slip rate is poorly constrained.

A 'more-than-representational' mapping study

DEFF Research Database (Denmark)

Lanng, Ditte Bendix

2018-01-01

through a concrete mapping study of a suburban site of lived mobilities and mundane architectures. From this standpoint the paper elaborates three central attentions of mapping as a creative and reflected more-than-representational tool in urban design: the evocations of eventfulness of sites, intricate...

Sensitivity mapping for oil spill response. V. 1

International Nuclear Information System (INIS)

1997-01-01

Making and updating sensitivity maps are key activities in the oil spill contingency planning process. These maps convey essential information to spill responders by showing where the different coastal resources are, and by indicating environmentally sensitive areas. The making of a map involves assembling information on resources and deciding on what guidelines for spill response should be included, through consultation with relevant organizations. This can be done regardless of whether or not the benefits of computerized Geographic Information Systems and databases are available. Uses of sensitivity maps range from planning practical site-specific shore protection and clean-up to strategic planning for large remote areas. This report provides information and guidelines on different map types, categories of information to be included, and symbols, with reference to the different users and their requirements. (UK)

Potential sites for a spent unreprocessed fuel facility (SURFF), southwesten part of the Nevada Test Site

International Nuclear Information System (INIS)

Hoover, D.L.; Eckel, E.B.; Ohl, J.P.

1978-01-01

In the absence of specific criteria, the topography, geomorphology, and geology of Jackass Flats and vicinity in the southwestern part of the Nevada Test Site are evaluated by arbitrary guidelines for a Spent Unreprocessed Fuel Facility. The guidelines include requirements for surface slopes of less than 5%, 61 m of alluvium beneath the site, an area free of active erosion or deposition, lack of faults, a minimum area of 5 km 2 , no potential for flooding, and as many logistical support facilities as possible. The geology of the Jackass Flats area is similar to the rest of the Nevada Test Site in topographic relief (305-1,200 m), stratigraphy (complexly folded and faulted Paleozoic sediments overlain by Tertiary ash-flow tuffs and lavas overlain in turn by younger alluvium), and structure (Paleozoic thrust faults and folds, strike-slip faults, proximity to volcanic centers, and Basin and Range normal faults). Of the stratigraphic units at the potential Spent Unreprocessed Fuel Facility site in Jackass Flats, only the thickness and stability of the alluvium are of immediate importance. Basin and Range faults and a possible extension of the Mine Mountain fault need further investigation. The combination of a slope map and a simplified geologic and physiographic map into one map shows several potential sites for a Spent Unreprocessed Fuel Facility in Jackass Flats. The potential areas have slopes of less than 5% and contain only desert pavement or segmented pavement--the two physiographic categories having the greatest geomorphic and hydraulic stability. Before further work can be done, specific criteria for a Spent Unreprocessed Fuel Facility site must be defined. Following criteria definition, potential sites will require detailed topographic and geologic studies, subsurface investigations (including geophysical methods, trenching, and perhaps shallow drilling for faults in alluvium), detailed surface hydrologic studies, and possibly subsurface hydrologic studies

Preliminary map of peak horizontal ground acceleration for the Hanshin-Awaji earthquake of January 17, 1995, Japan - Description of Mapped Data Sets

Science.gov (United States)

Borcherdt, R.D.; Mark, R.K.

1995-01-01

The Hanshin-Awaji earthquake (also known as the Hyogo-ken Nanbu and the Great Hanshin earthquake) provided an unprecedented set of measurements of strong ground shaking. The measurements constitute the most comprehensive set of strong- motion recordings yet obtained for sites underlain by soft soil deposits of Holocene age within a few kilometers of the crustal rupture zone. The recordings, obtained on or near many important structures, provide an important new empirical data set for evaluating input ground motion levels and site amplification factors for codes and site-specific design procedures world wide. This report describes the data used to prepare a preliminary map summarizing the strong motion data in relation to seismicity and underlying geology (Wentworth, Borcherdt, and Mark., 1995; Figure 1, hereafter referred to as Figure 1/I). The map shows station locations, peak acceleration values, and generalized acceleration contours superimposed on pertinent seismicity and the geologic map of Japan. The map (Figure 1/I) indicates a zone of high acceleration with ground motions throughout the zone greater than 400 gal and locally greater than 800 gal. This zone encompasses the area of most intense damage mapped as JMA intensity level 7, which extends through Kobe City. The zone of most intense damage is parallel, but displaced slightly from the surface projection of the crustal rupture zone implied by aftershock locations. The zone is underlain by soft-soil deposits of Holocene age.

Physical mapping of a commonly deleted region, the site of a candidate tumor suppressor gene, at 12q22 in human male germ cell tumors

Energy Technology Data Exchange (ETDEWEB)

Murty, V.V.V.S.; Bosl, G.J.; Chaganti, R.S.K. [Memorial Sloan-Kettering Cancer Center, New York, NY (United States)] [and others

1996-08-01

A candidate tumor suppressor gene (TSG) site at 12q22 characterized by a high frequency of loss of heterozygosity (LOH) and a homozygous deletion has previously (LOH) and a homozygous deletion has previously been reported in human male germ cell tumors (GCTs). In a detailed deletion mapping analysis of 67 normal-tumor DNAs utilizing 20 polymorphic markers mapped to 12q22-q24, we identified the limits of the minimal region of deletion at 12q22 between D12S377 (priximal) and D12S296 (distal). We have constructed a YAC contig map of a 3-cM region of this band between the proximal marker D12S101 and the distal marker D12S346, which contained the minimal region of deletion in GCTs. The map is composed of 53 overlapping YACs and 3 cosmids onto which 25 polymorphic and nonpolymorphic sequence-tagged sites (STSs) were placed in a unique order. The size of the minimal region of deletion was approximately 2 Mb from overlapping, nonchimeric YACs that spanned the region. We also developed a radiation hybrid (RH) map of the region between D12S101 and D12S346 containing 17 loci. The consensus order developed by RH mapping is in good agreement with the YAC STS-content map order. The RH map estimated the distance between D12S101 and D12S346 to be 246 cR{sub 8000} and the minimal region of deletion to be 141 cR{sub 8000}. In addition, four genes that were previously mapped to 12q22 have been excluded as candidate genes. The leads gained from the deletion mapping and physical maps should expedite the isolation and characterization of the TSG at 12q22. 35 refs., 4 figs., 2 tabs.

Map showing selected surface-water data for the Huntington 30 x 60-minute quadrangle, Utah

Science.gov (United States)

Price, Don

1984-01-01

This is one of a series of maps that describe the geology and related natural resources of the Huntington 30 x 60-minute quadrangle, Utah. Streamflow records used to compile this map were collected by the U.S. Geological Survey in cooperation with the Utah Department of Natural Resources, Division of Water Rights, and the Utah Department of Transportation. The principal runoff-producing area shown on the map was delineated from a work map (scale 1:250,000) compiled to estimate water yields in Utah (Bagley and others, 1964). Sources of information about recorded floods resulting from cloudbursts included Woolley (1946) and Butler and Marsell (1972); sources of information about the chemical quality of streamflow included Mundorff (1972) and Mundorff and Thompson (1982).

Map showing selected surface-water data for the Manti 30 x 60-minute Quadrangle, Utah

Science.gov (United States)

Price, Don

1984-01-01

This is one of a series of maps that describe the geology and related natural resources of the Manti 30 x 60 minute quadrangle. Streamflow records used to compile this map were collected by the U.S. Geological Survey in cooperation with the Utah Department of Natural Resources, Division of Water Rights, and the Utah Department of Transportation. The principal runoff-producing areas shown on the map were delineated from a work map (scale 1:250,000) compiled to estimate water yields in Utah (Bagley and others, 1964). Sources of information about recorded floods resulting from cloudbursts included Woolley (1946) and Butler and Marsell (1972); sources of information about the chemical quality of streamflow included Hahl and Cabell (1965) and Mundorff and Thompson (1982).

Map showing selected surface-water data for the Price 30 x 60-minute Quadrangle, Utah

Science.gov (United States)

Price, Don

1984-01-01

This is one of a series of maps that describe the geology and related natural resources of the Price 30 x 60-minute quadrangle, Utah. Streamflow records used to compile this map were collected by the U.S. Geological Survey in cooperation with the Utah Department of Natural Resources, Division of Water Rights, and the Utah Department of Transportation. The principal runoff-producing areas shown on the map were delineated from a work map (scale 1:250,000) compiled to estimate water yields in Utah (Bagley and others, 1964). Sources of information about recorded floods resulting from cloudbursts included Woolley (1946) and Butler and Marsell (1972); sources of information about the chemical quality of streamflow included Mundorff (1972; 1977), and Waddell and others (1982).

Dynamic Digital Maps as Vehicles for Distributing Digital Geologic Maps and Embedded Analytical Data and Multimedia

Science.gov (United States)

Condit, C. D.; Mninch, M.

2012-12-01

The Dynamic Digital Map (DDM) is an ideal vehicle for the professional geologist to use to describe the geologic setting of key sites to the public in a format that integrates and presents maps and associated analytical data and multimedia without the need for an ArcGIS interface. Maps with field trip guide stops that include photographs, movies and figures and animations, showing, for example, how the features seen in the field formed, or how data might be best visualized in "time-frame" sequences are ideally included in DDMs. DDMs distribute geologic maps, images, movies, analytical data, and text such as field guides, in an integrated cross-platform, web enabled format that are intuitive to use, easily and quickly searchable, and require no additional proprietary software to operate. Maps, photos, movies and animations are stored outside the program, which acts as an organizational framework and index to present these data. Once created, the DDM can be downloaded from the web site hosting it in the flavor matching the user's operating system (e.g. Linux, Windows and Macintosh) as zip, dmg or tar files (and soon as iOS and Android tablet apps). When decompressed, the DDM can then access its associated data directly from that site with no browser needed. Alternatively, the entire package can be distributed and used from CD, DVD, or flash-memory storage. The intent of this presentation is to introduce the variety of geology that can be accessed from the over 25 DDMs created to date, concentrating on the DDM of the Springerville Volcanic Field. We will highlight selected features of some of them, introduce a simplified interface to the original DDM (that we renamed DDMC for Classic) and give a brief look at a the recently (2010-2011) completed geologic maps of the Springerville Volcanic field to see examples of each of the features discussed above, and a display of the integrated analytical data set. We will also highlight the differences between the classic or

DEVELOPMENT OF TECHNIQUE FOR ZONING THE FORMER SEMIPALATINSK TEST SITE TERRITORY USINHG GEOINFORMATIONAL MAPPING

Directory of Open Access Journals (Sweden)

Yu. Yu. Yakovenko

2016-01-01

Full Text Available The paper presents the results of studies on radio-ecological assessment of pollution carried out at the former Semipalatinsk test site. The technique of radio-ecological zoning with methods of geoinformation mapping, including the determination of qualitative and qualitative criteria depending on the degree of superficial soil layer pollution, exposed to anthropogenic radiative impact, is offered. The result of such zoning makes it possible to evaluate the degree of radiation impact on the surveyed area, identify areas with high background radiation and define the borders representing potential risks to the public, residing or carrying out business activities within the area.

Insights into earthquake hazard map performance from shaking history simulations

Science.gov (United States)

Stein, S.; Vanneste, K.; Camelbeeck, T.; Vleminckx, B.

2017-12-01

Why recent large earthquakes caused shaking stronger than predicted by earthquake hazard maps is under debate. This issue has two parts. Verification involves how well maps implement probabilistic seismic hazard analysis (PSHA) ("have we built the map right?"). Validation asks how well maps forecast shaking ("have we built the right map?"). We explore how well a map can ideally perform by simulating an area's shaking history and comparing "observed" shaking to that predicted by a map generated for the same parameters. The simulations yield shaking distributions whose mean is consistent with the map, but individual shaking histories show large scatter. Infrequent large earthquakes cause shaking much stronger than mapped, as observed. Hence, PSHA seems internally consistent and can be regarded as verified. Validation is harder because an earthquake history can yield shaking higher or lower than that predicted while being consistent with the hazard map. The scatter decreases for longer observation times because the largest earthquakes and resulting shaking are increasingly likely to have occurred. For the same reason, scatter is much less for the more active plate boundary than for a continental interior. For a continental interior, where the mapped hazard is low, even an M4 event produces exceedances at some sites. Larger earthquakes produce exceedances at more sites. Thus many exceedances result from small earthquakes, but infrequent large ones may cause very large exceedances. However, for a plate boundary, an M6 event produces exceedance at only a few sites, and an M7 produces them in a larger, but still relatively small, portion of the study area. As reality gives only one history, and a real map involves assumptions about more complicated source geometries and occurrence rates, which are unlikely to be exactly correct and thus will contribute additional scatter, it is hard to assess whether misfit between actual shaking and a map — notably higher-than-mapped

Site maps and facilities listings

Energy Technology Data Exchange (ETDEWEB)

1993-11-01

In September 1989, a Memorandum of Agreement among DOE offices regarding the environmental management of DOE facilities was signed by appropriate Assistant Secretaries and Directors. This Memorandum of Agreement established the criteria for EM line responsibility. It stated that EM would be responsible for all DOE facilities, operations, or sites (1) that have been assigned to DOE for environmental restoration and serve or will serve no future production need; (2) that are used for the storage, treatment, or disposal of hazardous, radioactive, and mixed hazardous waste materials that have been properly characterized, packaged, and labelled, but are not used for production; (3) that have been formally transferred to EM by another DOE office for the purpose of environmental restoration and the eventual return to service as a DOE production facility; or (4) that are used exclusively for long-term storage of DOE waste material and are not actively used for production, with the exception of facilities, operations, or sites under the direction of the DOE Office of Civilian Radioactive Waste Management. As part of the implementation of the Memorandum of Agreement, Field Offices within DOE submitted their listings of facilities, systems, operation, and sites for which EM would have line responsibility. It is intended that EM facility listings will be revised on a yearly basis so that managers at all levels will have a valid reference for the planning, programming, budgeting and execution of EM activities.

Site maps and facilities listings

International Nuclear Information System (INIS)

1993-11-01

In September 1989, a Memorandum of Agreement among DOE offices regarding the environmental management of DOE facilities was signed by appropriate Assistant Secretaries and Directors. This Memorandum of Agreement established the criteria for EM line responsibility. It stated that EM would be responsible for all DOE facilities, operations, or sites (1) that have been assigned to DOE for environmental restoration and serve or will serve no future production need; (2) that are used for the storage, treatment, or disposal of hazardous, radioactive, and mixed hazardous waste materials that have been properly characterized, packaged, and labelled, but are not used for production; (3) that have been formally transferred to EM by another DOE office for the purpose of environmental restoration and the eventual return to service as a DOE production facility; or (4) that are used exclusively for long-term storage of DOE waste material and are not actively used for production, with the exception of facilities, operations, or sites under the direction of the DOE Office of Civilian Radioactive Waste Management. As part of the implementation of the Memorandum of Agreement, Field Offices within DOE submitted their listings of facilities, systems, operation, and sites for which EM would have line responsibility. It is intended that EM facility listings will be revised on a yearly basis so that managers at all levels will have a valid reference for the planning, programming, budgeting and execution of EM activities

Map showing selected surface-water data for the Nephi 30 x 60-minute quadrangle, Utah

Science.gov (United States)

Price, Don

1984-01-01

This is one of a series of maps that describe the geology and related natural resources of the Nephi 30 x 60 minute quadrangle, Utah. Streamflow records used to compile this map were collected by the U.S. Geological Survey in cooperation with the Utah Department of Natural Resources, Division of Water Rights, and the Utah Department of Transportation. The principal runoff-producing areas shown on the map were delineated from a work map (scale 1:250,000) compiled to estimate water yields in Utah (Bagley and others, 1964). Sources of information about recorded floods resulting from cloudbursts included Woolley (1946) and Butler and Marsell (1972); sources of information about the chemical quality of streamflow included Hahl and Cabell (1965) Mundorff (1972 and 1974), and Waddell and others (1982).

Nanobodies: site-specific labeling for super-resolution imaging, rapid epitope-mapping and native protein complex isolation

Science.gov (United States)

Pleiner, Tino; Bates, Mark; Trakhanov, Sergei; Lee, Chung-Tien; Schliep, Jan Erik; Chug, Hema; Böhning, Marc; Stark, Holger; Urlaub, Henning; Görlich, Dirk

2015-01-01

Nanobodies are single-domain antibodies of camelid origin. We generated nanobodies against the vertebrate nuclear pore complex (NPC) and used them in STORM imaging to locate individual NPC proteins with nanobody sequence and labeled the resulting proteins with fluorophore-maleimides. As nanobodies are normally stabilized by disulfide-bonded cysteines, this appears counterintuitive. Yet, our analysis showed that this caused no folding problems. Compared to traditional NHS ester-labeling of lysines, the cysteine-maleimide strategy resulted in far less background in fluorescence imaging, it better preserved epitope recognition and it is site-specific. We also devised a rapid epitope-mapping strategy, which relies on crosslinking mass spectrometry and the introduced ectopic cysteines. Finally, we used different anti-nucleoporin nanobodies to purify the major NPC building blocks – each in a single step, with native elution and, as demonstrated, in excellent quality for structural analysis by electron microscopy. The presented strategies are applicable to any nanobody and nanobody-target. DOI: http://dx.doi.org/10.7554/eLife.11349.001 PMID:26633879

Computer-aided mapping of stream channels beneath the Lawrence Livermore National Laboratory Super Fund Site

Energy Technology Data Exchange (ETDEWEB)

Sick, M. [Lawrence Livermore National Lab., CA (United States)

1994-12-01

The Lawrence Livermore National Laboratory (LLNL) site rests upon 300-400 feet of highly heterogeneous braided stream sediments which have been contaminated by a plume of Volatile Organic Compounds (VOCs). The stream channels are filled with highly permeable coarse grained materials that provide quick avenues for contaminant transport. The plume of VOCs has migrated off site in the TFA area, making it the area of greatest concern. I mapped the paleo-stream channels in the TFA area using SLICE an LLNL Auto-CADD routine. SLICE constructed 2D cross sections and sub-horizontal views of chemical, geophysical, and lithologic data sets. I interpreted these 2D views as a braided stream environment, delineating the edges of stream channels. The interpretations were extracted from Auto-CADD and placed into Earth Vision`s 3D modeling and viewing routines. Several 3D correlations have been generated, but no model has yet been chosen as a best fit.

Mapping DNA cleavage by the Type ISP restriction-modification enzymes following long-range communication between DNA sites in different orientations

Science.gov (United States)

van Aelst, Kara; Saikrishnan, Kayarat; Szczelkun, Mark D.

2015-01-01

The prokaryotic Type ISP restriction-modification enzymes are single-chain proteins comprising an Mrr-family nuclease, a superfamily 2 helicase-like ATPase, a coupler domain, a methyltransferase, and a DNA-recognition domain. Upon recognising an unmodified DNA target site, the helicase-like domain hydrolyzes ATP to cause site release (remodeling activity) and to then drive downstream translocation consuming 1–2 ATP per base pair (motor activity). On an invading foreign DNA, double-strand breaks are introduced at random wherever two translocating enzymes form a so-called collision complex following long-range communication between a pair of target sites in inverted (head-to-head) repeat. Paradoxically, structural models for collision suggest that the nuclease domains are too far apart (>30 bp) to dimerise and produce a double-strand DNA break using just two strand-cleavage events. Here, we examined the organisation of different collision complexes and how these lead to nuclease activation. We mapped DNA cleavage when a translocating enzyme collides with a static enzyme bound to its site. By following communication between sites in both head-to-head and head-to-tail orientations, we could show that motor activity leads to activation of the nuclease domains via distant interactions of the helicase or MTase-TRD. Direct nuclease dimerization is not required. To help explain the observed cleavage patterns, we also used exonuclease footprinting to demonstrate that individual Type ISP domains can swing off the DNA. This study lends further support to a model where DNA breaks are generated by multiple random nicks due to mobility of a collision complex with an overall DNA-binding footprint of ∼30 bp. PMID:26507855

Site characterization of the West Chestnut Ridge site

International Nuclear Information System (INIS)

Ketelle, R.H.; Huff, D.D.

1984-09-01

This report summarizes the results of investigations performed to date on the West Chestnut Ridge Site, on the Department of Energy (DOE) Oak Ridge Reservation. The investigations performed include geomorphic observations, areal geologic mapping, surficial soil mapping, subsurface investigations, soil geochemical and mineralogical analyses, geohydrologic testing, groundwater fluctuation monitoring, and surface water discharge and precipitation monitoring. 33 references, 32 figures, 24 tables

Derivation of elastic stiffness from site-matched mineral density and acoustic impedance maps

International Nuclear Information System (INIS)

Raum, Kay; Cleveland, Robin O; Peyrin, Francoise; Laugier, Pascal

2006-01-01

200 MHz acoustic impedance maps and site-matched synchrotron radiation micro computed tomography (SR-μCT) maps of tissue degree of mineralization of bone (DMB) were used to derive the elastic coefficient c 33 in cross sections of human cortical bone. To accomplish this goal, a model was developed to relate the DMB accessible with SR-μCT to mass density. The formulation incorporates the volume fractions and densities of the major bone tissue components (collagen, mineral and water), and accounts for tissue porosity. We found that the mass density can be well modelled by a second-order polynomial fit to DMB (R 2 = 0.999) and appears to be consistent with measurements of many different types of mineralized tissues. The derived elastic coefficient c 33 correlated more strongly with the acoustic impedance (R 2 = 0.996) than with mass density (R 2 = 0.310). This finding suggests that estimates of c 33 made from measurements of the acoustic impedance are more reliable than those made from density measurements. Mass density and elastic coefficient were in the range between 1.66 and 2.00 g cm -3 and 14.8 and 75.4 GPa, respectively. Although SAM inspection is limited to the evaluation of carefully prepared sample surfaces, it provides a two-dimensional quantitative estimate of elastic tissue properties at the tissue level

Global Mapping of Transcription Factor Binding Sites by Sequencing Chromatin Surrogates: a Perspective on Experimental Design, Data Analysis, and Open Problems.

Science.gov (United States)

Wei, Yingying; Wu, George; Ji, Hongkai

2013-05-01

Mapping genome-wide binding sites of all transcription factors (TFs) in all biological contexts is a critical step toward understanding gene regulation. The state-of-the-art technologies for mapping transcription factor binding sites (TFBSs) couple chromatin immunoprecipitation (ChIP) with high-throughput sequencing (ChIP-seq) or tiling array hybridization (ChIP-chip). These technologies have limitations: they are low-throughput with respect to surveying many TFs. Recent advances in genome-wide chromatin profiling, including development of technologies such as DNase-seq, FAIRE-seq and ChIP-seq for histone modifications, make it possible to predict in vivo TFBSs by analyzing chromatin features at computationally determined DNA motif sites. This promising new approach may allow researchers to monitor the genome-wide binding sites of many TFs simultaneously. In this article, we discuss various experimental design and data analysis issues that arise when applying this approach. Through a systematic analysis of the data from the Encyclopedia Of DNA Elements (ENCODE) project, we compare the predictive power of individual and combinations of chromatin marks using supervised and unsupervised learning methods, and evaluate the value of integrating information from public ChIP and gene expression data. We also highlight the challenges and opportunities for developing novel analytical methods, such as resolving the one-motif-multiple-TF ambiguity and distinguishing functional and non-functional TF binding targets from the predicted binding sites. The online version of this article (doi:10.1007/s12561-012-9066-5) contains supplementary material, which is available to authorized users.

Site-condition map for Portugal, Western Iberia: methodology and constraints on the performance of Vs30 proxies for stable continental regions in Europe.

Science.gov (United States)

Vilanova, S. P.; Narciso, J.; Carvalho, J. P.; Cancela, C.; Lopes, I.; Nemser, E. S.; Borges, J.

2014-12-01

Information on the amplification characteristics of the near-surface formations in a regional sense is essential to adequately represent both seismic hazard maps and ground shaking maps. Due to the scarceness of shear-wave velocity data in most regions, several methods have been proposed in order to obtain first order representations of Vs30. These include the surface geology method and the topographic slope method. The latter method has become the standard way for incorporating site effects into regional studies worldwide given the convenience provided by the global Vs30 Internet server. In the framework of project SCENE we developed a shear wave velocity database for Portugal. The database consists of 87 shear-wave velocity depth profiles from a variety of lithological and geological formations. We used an iterative three-step procedure to develop the Vs30 based site-condition map: 1) to define a preliminary set of geologically defined units based on the literature; 2) to calculate the distribution of Vs30 for each unit; and 3) to perform statistical tests in order to estimate the significance of the difference in the Vs30 distribution characteristics between the units. The units were merged according to the results of the statistical tests and the procedure was repeated. We started by classifying the sites into six generalized geological units. The final set consists of three units only: F1 (igneous, metamorphic and old sedimentary rocks); F2 (Neogene and Pleistocene formations); and F3 (Holocene deposits). We used the database to evaluate the performance of Vs30 proxies. The use of proxies based either on geological units or on correlations with the topographic slope shows relatively unbiased total residual distributions of the logarithm of Vs30. However, the performance of the methods varies significantly with the generalized geological unit analyzed. Both methods are biased towards lower values of Vs30 for rock formations. The topographic-slope method is

Map showing geology, oil and gas fields, and geologic provinces of the Gulf of Mexico region

Science.gov (United States)

French, Christopher D.; Schenk, Christopher J.

2006-01-01

This map was created as part of a worldwide series of geologic maps for the U.S. Geological Survey's World Energy Project. These products are available on CD-ROM and the Internet. The goal of the project is to assess the undiscovered, technically recoverable oil and gas resources of the world. Two previously published digital geologic data sets (U.S. and Caribbean) were clipped to the map extent, while the dataset for Mexico was digitized for this project. Original attributes for all data layers were maintained, and in some cases, graphically merged with common symbology for presentation purposes. The world has been divided into geologic provinces that are used for allocation and prioritization of oil and gas assessments. For the World Energy Project, a subset of those provinces is shown on this map. Each province has a set of geologic characteristics that distinguish it from surrounding provinces. These characteristics may include dominant lithologies, the age of the strata, and/or structural type. The World Geographic Coordinate System of 1984 is used for data storage, and the data are presented in a Lambert Conformal Conic Projection on the OFR 97-470-L map product. Other details about the map compilation and data sources are provided in metadata documents in the data section on this CD-ROM. Several software packages were used to create this map including: Environmental Systems Research Institute, Inc. (ESRI) ArcGIS 8.3, ArcInfo software, Adobe Photoshop CS, Illustrator CS, and Acrobat 6.0.

A remote characterization system for subsurface mapping of buried waste sites

International Nuclear Information System (INIS)

Sandness, G.A.; Bennett, D.W.

1992-10-01

Mapping of buried objects and regions of chemical and radiological contamination is required at US Department of Energy (DOE) buried waste sites. The DOE Office of Technology Development Robotics Integrated Program has initiated a project to develop and demonstrate a remotely controlled subsurface sensing system, called the Remote Characterization System (RCS). This project, a collaborative effort by five of the National Laboratories, involves the development of a unique low-signature survey vehicle, a base station, radio telemetry data links, satellite-based vehicle tracking, stereo vision, and sensors for non-invasive inspection of the surface and subsurface. To minimize interference with on-board sensors, the survey vehicle has been constructed predominatantly of non-metallic materials. The vehicle is self-propelled and will be guided by an operator located at a remote base station. The RCS sensors will be environmentally sealed and internally cooled to preclude contamination during use. Ground-penetrating radar, magnetometers, and conductivity devices are planned for geophysical surveys. Chemical and radiological sensors will be provided to locate hot spots and to provide isotopic concentration data

Large-Scale Mapping of Carbon Stocks in Riparian Forests with Self-Organizing Maps and the k-Nearest-Neighbor Algorithm

Directory of Open Access Journals (Sweden)

Leonhard Suchenwirth

2014-07-01

Full Text Available Among the machine learning tools being used in recent years for environmental applications such as forestry, self-organizing maps (SOM and the k-nearest neighbor (kNN algorithm have been used successfully. We applied both methods for the mapping of organic carbon (Corg in riparian forests due to their considerably high carbon storage capacity. Despite the importance of floodplains for carbon sequestration, a sufficient scientific foundation for creating large-scale maps showing the spatial Corg distribution is still missing. We estimated organic carbon in a test site in the Danube Floodplain based on RapidEye remote sensing data and additional geodata. Accordingly, carbon distribution maps of vegetation, soil, and total Corg stocks were derived. Results were compared and statistically evaluated with terrestrial survey data for outcomes with pure remote sensing data and for the combination with additional geodata using bias and the Root Mean Square Error (RMSE. Results show that SOM and kNN approaches enable us to reproduce spatial patterns of riparian forest Corg stocks. While vegetation Corg has very high RMSEs, outcomes for soil and total Corg stocks are less biased with a lower RMSE, especially when remote sensing and additional geodata are conjointly applied. SOMs show similar percentages of RMSE to kNN estimations.

Flood-inundation maps for the Schoharie Creek at Prattsville, New York, 2014

Science.gov (United States)

Nystrom, Elizabeth A.

2016-02-18

Digital flood-inundation maps for a 2.6-mile reach of the Schoharie Creek at Prattsville, New York, were created by the U.S. Geological Survey (USGS) in cooperation with the New York State Department of Environmental Conservation. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at Schoharie Creek at Prattsville (station number 01350000). Near-real-time stages at this streamgage may be obtained online from the USGS National Water Information System (http://waterdata.usgs.gov/) or the National Weather Service Advanced Hydrologic Prediction Service (http://water.weather.gov/ahps/), which also forecasts flood hydrographs at this site. National Weather Service-forecasted peak-stage information may be used in conjunction with the maps developed in this study to show predicted areas and depths of flood inundation.

Marine Benthic Habitats and Seabed Suitability Mapping for Potential Ocean Current Energy Siting Offshore Southeast Florida

Directory of Open Access Journals (Sweden)

Amanda Mulcan

2015-05-01

Full Text Available This study examines the legal framework for ocean current energy policy and regulation to develop a metric for assessing the biological and geological characteristics of a seabed area with respect to the siting of OCE devices, a framework of criteria by which to assess seabed suitability (seabed suitability framework that can facilitate the siting, and implementation of ocean current energy (OCE projects. Seafloor geology and benthic biological data were analyzed in conjunction with seafloor core sample geostatistical interpolation to locate suitable substrates for OCE anchoring. Existing submarine cable pathways were considered to determine pathways for power transmission cables that circumvent biologically sensitive areas. Suitability analysis indicates that areas east of the Miami Terrace and north of recently identified deep-sea coral mounds are the most appropriate for OCE siting due to abundance of sand/sediment substrate, existing underwater cable route access, and minimal biological presence (i.e., little to no benthic communities. Further reconnaissance requires higher resolution maps of geological substrate and benthic community locations to identify specific OCE development locations, classify benthic conditions, and minimize potentially negative OCE environmental impacts.

Maps showing geology, oil and gas fields, and geological provinces of South America

Science.gov (United States)

Schenk, C. J.; Viger, R.J.; Anderson, C.P.

1999-01-01

This digitally compiled map includes geology, geologic provinces, and oil and gas fields of South America. The map is part of a worldwide series on CD-ROM by World Energy Project released of the U.S. Geological Survey . The goal of the project is to assess the undiscovered, technically recoverable oil and gas resources of the world and report these results by the year 2000. For data management purposes the world is divided into eight energy regions corresponding approximately to the economic regions of the world as defined by the U.S. Department of State. South America (Region 6) includes Argentina, Bolivia, Brazil, Chile, Columbia, Ecuador, Falkland Islands, French Guiana, Guyuna, Netherlands, Netherlands Antilles, Paraguay, Peru, Suriname, Trinidad and Tobago, Uruguay, and Venezuela.

International Journal of Engineering, Science and Technology: Site ...

African Journals Online (AJOL)

International Journal of Engineering, Science and Technology: Site Map. Journal Home > About the Journal > International Journal of Engineering, Science and Technology: Site Map. Log in or Register to get access to full text downloads.

Agroforestry suitability analysis based upon nutrient availability mapping: a GIS based suitability mapping

Directory of Open Access Journals (Sweden)

Firoz Ahmad

2017-05-01

Full Text Available Agroforestry has drawn the attention of researchers due to its capacity to reduce the poverty and land degradation, improve food security and mitigate the climate change. However, the progress in promoting agroforestry is held back due to the lack of reliable data sets and appropriate tools to accurately map and to have an adequate decision making system for agroforestry modules. Agroforestry suitability being one special form of land suitability is very pertinent to study in the current times when there is tremendous pressure on the land as it is a limited commodity. The study aims for applying the geo-spatial tools towards visualizing various soil and environmental data to reveal the trends and interrelationships and to achieve a nutrient availability and agroforestry suitability map. Using weight matrix and ranks, individual maps were developed in ArcGIS 10.1 platform to generate nutrient availability map, which was later used to develop agroforestry suitability map. Watersheds were delineated using DEM in some part of the study area and were evaluated for prioritizing it and agroforestry suitability of the watersheds were also done as per the schematic flowchart. Agroforestry suitability regions were delineated based upon the weight and ranks by integrated mapping. The total open area was identified 42.4% out of which 21.6% area was found to have high suitability towards agroforestry. Within the watersheds, 22 village points were generated for creating buffers, which were further evaluated showing its proximity to high suitable agroforestry sites thus generating tremendous opportunity to the villagers to carry out agroforestry projects locally. This research shows the capability of remote sensing in studying agroforestry practices and in estimating the prominent factors for its optimal productivity. The ongoing agroforestry projects can be potentially diverted in the areas of high suitability as an extension. The use of ancillary data in GIS

GIS-aided low flow mapping

Science.gov (United States)

Saghafian, B.; Mohammadi, A.

2003-04-01

Most studies involving water resources allocation, water quality, hydropower generation, and allowable water withdrawal and transfer require estimation of low flows. Normally, frequency analysis on at-station D-day low flow data is performed to derive various T-yr return period values. However, this analysis is restricted to the location of hydrometric stations where the flow discharge is measured. Regional analysis is therefore conducted to relate the at-station low flow quantiles to watershed characteristics. This enables the transposition of low flow quantiles to ungauged sites. Nevertheless, a procedure to map the regional regression relations for the entire stream network, within the bounds of the relations, is particularly helpful when one studies and weighs alternative sites for certain water resources project. In this study, we used a GIS-aided procedure for low flow mapping in Gilan province, part of northern region in Iran. Gilan enjoys a humid climate with an average of 1100 mm annual precipitation. Although rich in water resources, the highly populated area is quite dependent on minimum amount of water to sustain the vast rice farming and to maintain required flow discharge for quality purposes. To carry out the low flow analysis, a total of 36 hydrometric stations with sufficient and reliable discharge data were identified in the region. The average area of the watersheds was 250 sq. km. Log Pearson type 3 was found the best distribution for flow durations over 60 days, while log normal fitted well the shorter duration series. Low flows with return periods of 2, 5, 10, 25, 50, and 100 year were then computed. Cluster analysis identified two homogeneous areas. Although various watershed parameters were examined in factor analysis, the results showed watershed area, length of the main stream, and annual precipitation were the most effective low flow parameters. The regression equations were then mapped with the aid of GIS based on flow accumulation maps

Map showing the distribution and characteristics of plutonic rocks in the Tonopah 1 degree by 2 degrees Quadrangle, central Nevada

Science.gov (United States)

John, D.A.

1987-01-01

Plutonic rocks, mostly granite and granodiorite, are widely distributed in the west two-thirds of the Tonopah 1 degree by 2 degree quadrangle, Nevada. These rocks were systematically studied as part of the Tonopah CUSMAP project. Studies included field mapping, petrographic and modal analyses, geochemical studies of both fresh and altered plutonic rocks and altered wallrocks, and K-Ar and Rb-Sr radiometric dating. Data collected during this study were combined with previously published data to produce a 1:250,000-scale map of the Tonopah quadrangle showing the distribution of individual plutons and an accompanying table summarizing composition, texture, age, and any noted hydrothermal alteration and mineralization effects for each pluton.

Seismic Intensity Map Triggered by Observed Strong Motion Records Considering Site Amplification and its service based on Geo-spatial International Standard

International Nuclear Information System (INIS)

Matsuoka, Masashi

2014-01-01

Instrumental seismic intensity measurement is carried out at approximately 4,200 points in Japan, but the correct values at points without seismometers cannot always be provided because seismic motion depends on geologic and geomorphologic features. Quick provision of accurate information on seismic intensity distribution over wide areas is required for disaster mitigation. To estimate seismic intensity at specific points, it is important to prepare ground amplification characteristics for local areas beforehand and use an interpolation algorithm. The QuiQuake system (quick estimation system for earthquake maps triggered by using observation records from K-NET and KiK-net that have been released by the National Research Institute for Earth Science and Disaster Prevention), which uses these, was developed; it can be started up automatically using seismograms and can immediately display a seismic intensity distribution map. The calculation results are sent to IAEA and JNES in the form of strong motion evaluation maps with a mesh size of 250 x 250 m. These maps are also sent to the general public via social networking web sites. (author)

Wildlife studies on the Hanford site: 1994 Highlights report

Energy Technology Data Exchange (ETDEWEB)

Cadwell, L.L. [ed.

1995-04-01

The purposes of the project are to monitor and report trends in wildlife populations; conduct surveys to identify, record, and map populations of threatened, endangered, and sensitive plant and animal species; and cooperate with Washington State and federal and private agencies to help ensure the protection afforded by law to native species and their habitats. Census data and results of surveys and special study topics are shared freely among cooperating agencies. Special studies are also conducted as needed to provide additional information that may be required to assess, protect, or manage wildlife resources at Hanford. This report describes highlights of wildlife studies on the Site in 1994. Redd counts of fall chinook salmon in the Hanford Reach suggest that harvest restrictions directed at protecting Snake River salmon may have helped Columbia River stocks as well. The 1994 count (5619) was nearly double that of 1993 and about 63% of the 1989 high of approximately 9000. A habitat map showing major vegetation and land use cover types for the Hanford Site was completed in 1993. During 1994, stochastic simulation was used to estimate shrub characteristics (height, density, and canopy cover) across the previously mapped Hanford landscape. The information provided will be available for use in determining habitat quality for sensitive wildlife species. Mapping Site locations of plant species of concern continued during 1994. Additional sensitive plant species data from surveys conducted by TNC were archived. The 10 nesting pairs of ferruginous hawks that used the Hanford Site in 1993 represented approximately 25% of the Washington State population.

Wildlife studies on the Hanford site: 1994 Highlights report

International Nuclear Information System (INIS)

Cadwell, L.L.

1995-04-01

The purposes of the project are to monitor and report trends in wildlife populations; conduct surveys to identify, record, and map populations of threatened, endangered, and sensitive plant and animal species; and cooperate with Washington State and federal and private agencies to help ensure the protection afforded by law to native species and their habitats. Census data and results of surveys and special study topics are shared freely among cooperating agencies. Special studies are also conducted as needed to provide additional information that may be required to assess, protect, or manage wildlife resources at Hanford. This report describes highlights of wildlife studies on the Site in 1994. Redd counts of fall chinook salmon in the Hanford Reach suggest that harvest restrictions directed at protecting Snake River salmon may have helped Columbia River stocks as well. The 1994 count (5619) was nearly double that of 1993 and about 63% of the 1989 high of approximately 9000. A habitat map showing major vegetation and land use cover types for the Hanford Site was completed in 1993. During 1994, stochastic simulation was used to estimate shrub characteristics (height, density, and canopy cover) across the previously mapped Hanford landscape. The information provided will be available for use in determining habitat quality for sensitive wildlife species. Mapping Site locations of plant species of concern continued during 1994. Additional sensitive plant species data from surveys conducted by TNC were archived. The 10 nesting pairs of ferruginous hawks that used the Hanford Site in 1993 represented approximately 25% of the Washington State population

Phosphorylation sites of Arabidopsis MAP Kinase Substrate 1 (MKS1)

DEFF Research Database (Denmark)

Caspersen, M.B.; Qiu, J.-L.; Zhang, X.

2007-01-01

The Arabidopsis MAP kinase 4 (MPK4) substrate MKS1 was expressed in Escherichia coli and purified, full-length, 6x histidine (His)-tagged MKS1 was phosphorylated in vitro by hemagglutinin (HA)-tagged MPK4 immuno-precipitated from plants. MKS1 phosphorylation was initially verified by electrophore......The Arabidopsis MAP kinase 4 (MPK4) substrate MKS1 was expressed in Escherichia coli and purified, full-length, 6x histidine (His)-tagged MKS1 was phosphorylated in vitro by hemagglutinin (HA)-tagged MPK4 immuno-precipitated from plants. MKS1 phosphorylation was initially verified...... phosphopeptide detection. As MAP kinases generally phosphorylate serine or threonine followed by proline (Ser/Thr-Pro), theoretical masses of potentially phosphorylated peptides were calculated and mass spectrometric peaks matching these masses were fragmented and searched for a neutral-loss signal...... at approximately 98 Da indicative of phosphorylation. Additionally, mass spectrometric peaks present in the MPK4-treated MKS1, but not in the control peptide map of untreated MKS1, were fragmented. Fragmentation spectra were subjected to a MASCOT database search which identified three of the twelve Ser-Pro serine...

Igs expressed by chronic lymphocytic leukemia B cells show limited binding-site structure variability.

Science.gov (United States)

Marcatili, Paolo; Ghiotto, Fabio; Tenca, Claudya; Chailyan, Anna; Mazzarello, Andrea N; Yan, Xiao-Jie; Colombo, Monica; Albesiano, Emilia; Bagnara, Davide; Cutrona, Giovanna; Morabito, Fortunato; Bruno, Silvia; Ferrarini, Manlio; Chiorazzi, Nicholas; Tramontano, Anna; Fais, Franco

2013-06-01

Ag selection has been suggested to play a role in chronic lymphocytic leukemia (CLL) pathogenesis, but no large-scale analysis has been performed so far on the structure of the Ag-binding sites (ABSs) of leukemic cell Igs. We sequenced both H and L chain V(D)J rearrangements from 366 CLL patients and modeled their three-dimensional structures. The resulting ABS structures were clustered into a small number of discrete sets, each containing ABSs with similar shapes and physicochemical properties. This structural classification correlates well with other known prognostic factors such as Ig mutation status and recurrent (stereotyped) receptors, but it shows a better prognostic value, at least in the case of one structural cluster for which clinical data were available. These findings suggest, for the first time, to our knowledge, on the basis of a structural analysis of the Ab-binding sites, that selection by a finite quota of antigenic structures operates on most CLL cases, whether mutated or unmutated.

POINT CLOUD MAPPING METHODS FOR DOCUMENTING CULTURAL LANDSCAPE FEATURES AT THE WORMSLOE STATE HISTORIC SITE, SAVANNAH, GEORGIA, USA

Directory of Open Access Journals (Sweden)

T. R. Jordana

2016-06-01

Full Text Available Documentation of the three-dimensional (3D cultural landscape has traditionally been conducted during site visits using conventional photographs, standard ground surveys and manual measurements. In recent years, there have been rapid developments in technologies that produce highly accurate 3D point clouds, including aerial LiDAR, terrestrial laser scanning, and photogrammetric data reduction from unmanned aerial systems (UAS images and hand held photographs using Structure from Motion (SfM methods. These 3D point clouds can be precisely scaled and used to conduct measurements of features even after the site visit has ended. As a consequence, it is becoming increasingly possible to collect non-destructive data for a wide variety of cultural site features, including landscapes, buildings, vegetation, artefacts and gardens. As part of a project for the U.S. National Park Service, a variety of data sets have been collected for the Wormsloe State Historic Site, near Savannah, Georgia, USA. In an effort to demonstrate the utility and versatility of these methods at a range of scales, comparisons of the features mapped with different techniques will be discussed with regards to accuracy, data set completeness, cost and ease-of-use.

Classification of sediments by means of Self-Organizing Maps and sediment quality guidelines in sites of the southern Spanish coastline

Directory of Open Access Journals (Sweden)

O. VESES

2013-08-01

Full Text Available This study was carried out to classify 112 marine and estuarine sites of the southern Spanish coastline (about 918 km long according to similar sediment characteristics by means of artificial neural networks (ANNs such as Self-Organizing Maps (SOM and sediment quality guidelines from a dataset consisted of 16 physical and chemical parameters including sediment granulometry, trace and major elements, total N and P and organic carbon content. The use of ANNs such as SOM made possible the classification of the sampling sites according to their similar chemical characteristics. Visual correlations between geochemical parameters were extracted due to the powerful visual characteristics (component planes of the SOM revealing that ANNs are an excellent tool to be incorporated in sediment quality assessments. Besides, almost 20% of the sites were classified as medium-high or high priority sites in order to take future remediation actions due to their high mean Effects Range-Median Quotient (m-ERMQ value. Priority sites included the estuaries of the major rivers (Tinto, Odiel, Palmones, etc. and several locations along the eastern coastline.

Ground-penetrating radar investigations conducted in the 100 areas, Hanford Site: Fiscal Year 1992

International Nuclear Information System (INIS)

Bergstrom, K.A.

1994-01-01

During Fiscal Year 1992, the Geophysics Group conducted forty- five Ground-Penetrating Radar (GPR) surveys in the 100 Areas (Figure 1) - Objectives for the investigations varied, from locating cribs, trenches and septic systems to helping site boreholes. The results of each investigation were delivered to clients in the form of a map that summarized the interpretation of a given site. No formal reports were prepared. The purpose of this document is to show where and why each of the surveys was conducted. The data and interpretation of each survey are available by contacting the Westinghouse Hanford Company, Geophysics Group. A map showing the location and basic parameters of each survey can be found in the Appendices of this report

Active Site Mapping of Human Cathepsin F with Dipeptide Nitrile Inhibitors.

Science.gov (United States)

Schmitz, Janina; Furtmann, Norbert; Ponert, Moritz; Frizler, Maxim; Löser, Reik; Bartz, Ulrike; Bajorath, Jürgen; Gütschow, Michael

2015-08-01

Cleavage of the invariant chain is the key event in the trafficking pathway of major histocompatibility complex class II. Cathepsin S is the major processing enzyme of the invariant chain, but cathepsin F acts in macrophages as its functional synergist which is as potent as cathepsin S in invariant chain cleavage. Dedicated low-molecular-weight inhibitors for cathepsin F have not yet been developed. An active site mapping with 52 dipeptide nitriles, reacting as covalent-reversible inhibitors, was performed to draw structure-activity relationships for the non-primed binding region of human cathepsin F. In a stepwise process, new compounds with optimized fragment combinations were designed and synthesized. These dipeptide nitriles were evaluated on human cysteine cathepsins F, B, L, K and S. Compounds 10 (N-(4-phenylbenzoyl)-leucylglycine nitrile) and 12 (N-(4-phenylbenzoyl)leucylmethionine nitrile) were found to be potent inhibitors of human cathepsin F, with Ki values nitriles from our study, a 3D activity landscape was generated to visualize structure-activity relationships for this series of cathepsin F inhibitors. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Rapid, Accurate, and Efficient Method to Map Heavy Metal-Contaminated Soils of Abandoned Mine Sites Using Converted Portable XRF Data and GIS

Directory of Open Access Journals (Sweden)

Jangwon Suh

2016-12-01

Full Text Available The use of portable X-ray fluorescence (PXRF and inductively coupled plasma atomic emission spectrometry (ICP-AES increases the rapidity and accuracy of soil contamination mapping, respectively. In practice, it is often necessary to repeat the soil contamination assessment and mapping procedure several times during soil management within a limited budget. In this study, we have developed a rapid, inexpensive, and accurate soil contamination mapping method using a PXRF data and geostatistical spatial interpolation. To obtain a large quantity of high quality data for interpolation, in situ PXRF data analyzed at 40 points were transformed to converted PXRF data using the correlation between PXRF and ICP-AES data. The method was applied to an abandoned mine site in Korea to generate a soil contamination map for copper and was validated for investigation speed and prediction accuracy. As a result, regions that required soil remediation were identified. Our method significantly shortened the time required for mapping compared to the conventional mapping method and provided copper concentration estimates with high accuracy similar to those measured by ICP-AES. Therefore, our method is an effective way of mapping soil contamination if we consistently construct a database based on the correlation between PXRF and ICP-AES data.

A microsatellite linkage map for Drosophila montana shows large variation in recombination rates, and a courtship song trait maps to an area of low recombination.

Science.gov (United States)

Schäfer, M A; Mazzi, D; Klappert, K; Kauranen, H; Vieira, J; Hoikkala, A; Ritchie, M G; Schlötterer, C

2010-03-01

Current advances in genetic analysis are opening up our knowledge of the genetics of species differences, but challenges remain, particularly for out-bred natural populations. We constructed a microsatellite-based linkage map for two out-bred lines of Drosophila montana derived from divergent populations by taking advantage of the Drosophila virilis genome and available cytological maps of both species. Although the placement of markers was quite consistent with cytological predictions, the map indicated large heterogeneity in recombination rates along chromosomes. We also performed a quantitative trait locus (QTL) analysis on a courtship song character (carrier frequency), which differs between populations and is subject to strong sexual selection. Linkage mapping yielded two significant QTLs, which explained 3% and 14% of the variation in carrier frequency, respectively. Interestingly, as in other recent studies of traits which can influence speciation, the strongest QTL mapped to a genomic region partly covered by an inversion polymorphism.

Geological ductile deformation mapping at the Olkiluoto site, Eurajoki, Finland

Energy Technology Data Exchange (ETDEWEB)

Engstroem, J. [Geological Survey of Finland, Espoo (Finland)

2013-12-15

During 2010-2012 eight larger excavated and cleaned outcrops were investigated to study the polyphase nature of the ductile deformation within the Olkiluoto Island. A detailed structural geological mapping together with a thin section study was performed to get a broader and better understanding of the nature and occurrence of these different ductile deformation phases. These outcrops were selected to represent all different ductile deformation phases recognized earlier during the site investigations. The relicts of primary sedimentary structures and products of the earliest deformations (D{sub 0}-D{sub 1}) are mostly obscured by later deformation events. The D{sub 2}-D{sub 4} is the most significant ductile deformation phases occurring on the Olkiluoto Island and almost all structural features can be labeled within these three phases. The outcrops for this investigation were selected mostly from the eastern part of the Olkiluoto Island because that part of the Island has been less investigated previously. As a reference, one outcrop was selected in the western part of the Island where it was previously known that this location had especially well preserved structures of the second deformation phase (D{sub 2}). The S{sub 2} foliation is E-W orientated with moderate dip towards south. A few folds can be associated with this deformational event, mostly having a tight to isoclinal character. During D{sub 3} the migmatites were re-deformed and migrated leucosomes, were intruded mainly parallel to S{sub 3} axial surfaces having a NE-SW orientation. Generally the dip of the S{sub 3} axial surfaces is slightly more steeper (55- 65 deg C) than that of the S{sub 2} axial surfaces, which shows a more moderate dip (40-65 deg C). F{sub 3} fold structures are quite common in the eastern part of Island showing asymmetrical, overturned, shear folds usually with a dextral sense of shear. Large scale D{sub 3} shear structures contain blastomylonites as characteristic fault rocks

Reproducibility of somatosensory spatial perceptual maps.

Science.gov (United States)

Steenbergen, Peter; Buitenweg, Jan R; Trojan, Jörg; Veltink, Peter H

2013-02-01

Various studies have shown subjects to mislocalize cutaneous stimuli in an idiosyncratic manner. Spatial properties of individual localization behavior can be represented in the form of perceptual maps. Individual differences in these maps may reflect properties of internal body representations, and perceptual maps may therefore be a useful method for studying these representations. For this to be the case, individual perceptual maps need to be reproducible, which has not yet been demonstrated. We assessed the reproducibility of localizations measured twice on subsequent days. Ten subjects participated in the experiments. Non-painful electrocutaneous stimuli were applied at seven sites on the lower arm. Subjects localized the stimuli on a photograph of their own arm, which was presented on a tablet screen overlaying the real arm. Reproducibility was assessed by calculating intraclass correlation coefficients (ICC) for the mean localizations of each electrode site and the slope and offset of regression models of the localizations, which represent scaling and displacement of perceptual maps relative to the stimulated sites. The ICCs of the mean localizations ranged from 0.68 to 0.93; the ICCs of the regression parameters were 0.88 for the intercept and 0.92 for the slope. These results indicate a high degree of reproducibility. We conclude that localization patterns of non-painful electrocutaneous stimuli on the arm are reproducible on subsequent days. Reproducibility is a necessary property of perceptual maps for these to reflect properties of a subject's internal body representations. Perceptual maps are therefore a promising method for studying body representations.

NHS-Esters As Versatile Reactivity-Based Probes for Mapping Proteome-Wide Ligandable Hotspots.

Science.gov (United States)

Ward, Carl C; Kleinman, Jordan I; Nomura, Daniel K

2017-06-16

Most of the proteome is considered undruggable, oftentimes hindering translational efforts for drug discovery. Identifying previously unknown druggable hotspots in proteins would enable strategies for pharmacologically interrogating these sites with small molecules. Activity-based protein profiling (ABPP) has arisen as a powerful chemoproteomic strategy that uses reactivity-based chemical probes to map reactive, functional, and ligandable hotspots in complex proteomes, which has enabled inhibitor discovery against various therapeutic protein targets. Here, we report an alkyne-functionalized N-hydroxysuccinimide-ester (NHS-ester) as a versatile reactivity-based probe for mapping the reactivity of a wide range of nucleophilic ligandable hotspots, including lysines, serines, threonines, and tyrosines, encompassing active sites, allosteric sites, post-translational modification sites, protein interaction sites, and previously uncharacterized potential binding sites. Surprisingly, we also show that fragment-based NHS-ester ligands can be made to confer selectivity for specific lysine hotspots on specific targets including Dpyd, Aldh2, and Gstt1. We thus put forth NHS-esters as promising reactivity-based probes and chemical scaffolds for covalent ligand discovery.

Geologic structure mapping database Spent Fuel Test - Climax, Nevada Test Site

International Nuclear Information System (INIS)

Yow, J.L. Jr.

1984-01-01

Information on over 2500 discontinuities mapped at the SFT-C is contained in the geologic structure mapping database. Over 1800 of these features include complete descriptions of their orientations. This database is now available for use by other researchers. 6 references, 3 figures, 2 tables

Arabidopsis Microtubule-Associated Protein MAP65-3 Cross-Links Antiparallel Microtubules toward Their Plus Ends in the Phragmoplast via Its Distinct C-Terminal Microtubule Binding Domain[W

Science.gov (United States)

Ho, Chin-Min Kimmy; Lee, Yuh-Ru Julie; Kiyama, Lindsay D.; Dinesh-Kumar, Savithramma P.; Liu, Bo

2012-01-01

Plant cytokinesis is brought about by the phragmoplast, which contains an antiparallel microtubule (MT) array. The MT-associated protein MAP65-3 acts as an MT-bundling factor that specifically cross-links antiparallel MTs near their plus ends. MAP65 family proteins contain an N-terminal dimerization domain and C-terminal MT interaction domain. Compared with other MAP65 isoforms, MAP65-3 contains an extended C terminus. A MT binding site was discovered in the region between amino acids 496 and 588 and found to be essential for the organization of phragmoplast MTs. The frequent cytokinetic failure caused by loss of MAP65-3 was not rescued by ectopic expression of MAP65-1 under the control of the MAP65-3 promoter, indicating nonoverlapping functions between the two isoforms. In the presence of MAP65-3, however, ectopic MAP65-1 appeared in the phragmoplast midline. We show that MAP65-1 could acquire the function of MAP65-3 when the C terminus of MAP65-3, which contains the MT binding site, was grafted to it. Our results also show that MAP65-1 and MAP65-3 may share redundant functions in MT stabilization. Such a stabilization effect was likely brought about by MT binding and bundling. We conclude that MAP65-3 contains a distinct C-terminal MT binding site with a specific role in cross-linking antiparallel MTs toward their plus ends in the phragmoplast. PMID:22570443

Movie-maps of low-latitude magnetic storm disturbance

Science.gov (United States)

Love, Jeffrey J.; Gannon, Jennifer L.

2010-06-01

We present 29 movie-maps of low-latitude horizontal-intensity magnetic disturbance for the years 1999-2006: 28 recording magnetic storms and 1 magnetically quiescent period. The movie-maps are derived from magnetic vector time series data collected at up to 25 ground-based observatories. Using a technique similar to that used in the calculation of Dst, a quiet time baseline is subtracted from the time series from each observatory. The remaining disturbance time series are shown in a polar coordinate system that accommodates both Earth rotation and the universal time dependence of magnetospheric disturbance. Each magnetic storm recorded in the movie-maps is different. While some standard interpretations about the storm time equatorial ring current appear to apply to certain moments and certain phases of some storms, the movie-maps also show substantial variety in the local time distribution of low-latitude magnetic disturbance, especially during storm commencements and storm main phases. All movie-maps are available at the U.S. Geological Survey Geomagnetism Program Web site (http://geomag.usgs.gov).

Southern Africa Journal of Education, Science and Technology: Site ...

African Journals Online (AJOL)

Southern Africa Journal of Education, Science and Technology: Site Map. Journal Home > About the Journal > Southern Africa Journal of Education, Science and Technology: Site Map. Log in or Register to get access to full text downloads.

Igs Expressed by Chronic Lymphocytic Leukemia B Cells Show Limited Binding-Site Structure Variability

KAUST Repository

Marcatili, P.

2013-05-01

Ag selection has been suggested to play a role in chronic lymphocytic leukemia (CLL) pathogenesis, but no large-scale analysis has been performed so far on the structure of the Ag-binding sites (ABSs) of leukemic cell Igs. We sequenced both H and L chain V(D)J rearrangements from 366 CLL patients and modeled their three-dimensional structures. The resulting ABS structures were clustered into a small number of discrete sets, each containing ABSs with similar shapes and physicochemical properties. This structural classification correlates well with other known prognostic factors such as Ig mutation status and recurrent (stereotyped) receptors, but it shows a better prognostic value, at least in the case of one structural cluster for which clinical data were available. These findings suggest, for the first time, to our knowledge, on the basis of a structural analysis of the Ab-binding sites, that selection by a finite quota of antigenic structures operates on most CLL cases, whether mutated or unmutated. Copyright © 2013 by The American Association of Immunologists, Inc.

Igs Expressed by Chronic Lymphocytic Leukemia B Cells Show Limited Binding-Site Structure Variability

KAUST Repository

Marcatili, P.; Ghiotto, F.; Tenca, C.; Chailyan, A.; Mazzarello, A. N.; Yan, X.-J.; Colombo, M.; Albesiano, E.; Bagnara, D.; Cutrona, G.; Morabito, F.; Bruno, S.; Ferrarini, M.; Chiorazzi, N.; Tramontano, A.; Fais, F.

2013-01-01

Ag selection has been suggested to play a role in chronic lymphocytic leukemia (CLL) pathogenesis, but no large-scale analysis has been performed so far on the structure of the Ag-binding sites (ABSs) of leukemic cell Igs. We sequenced both H and L chain V(D)J rearrangements from 366 CLL patients and modeled their three-dimensional structures. The resulting ABS structures were clustered into a small number of discrete sets, each containing ABSs with similar shapes and physicochemical properties. This structural classification correlates well with other known prognostic factors such as Ig mutation status and recurrent (stereotyped) receptors, but it shows a better prognostic value, at least in the case of one structural cluster for which clinical data were available. These findings suggest, for the first time, to our knowledge, on the basis of a structural analysis of the Ab-binding sites, that selection by a finite quota of antigenic structures operates on most CLL cases, whether mutated or unmutated. Copyright © 2013 by The American Association of Immunologists, Inc.

Radiation hybrid mapping as one of the main methods of the creation of high resolution maps of human and animal genomes

International Nuclear Information System (INIS)

Sulimova, G.E.; Kompanijtsev, A.A.; Mojsyak, E.V.; Rakhmanaliev, Eh.R.; Klimov, E.A.; Udina, I.G.; Zakharov, I.A.

2000-01-01

Radiation hybrid mapping (RH mapping) is considered as one of the main method of constructing physical maps of mammalian genomes. In introduction, theoretical prerequisites of developing of the RH mapping and statistical methods of data analysis are discussed. Comparative characteristics of universal commercial panels of the radiation hybrid somatic cells (RH panels) are shown. In experimental part of the work, RH mapping is used to localize nucleotide sequences adjacent to Not I sites of human chromosome 3 with the aim to integrate contig map of Nor I clones to comprehensive maps of human genome. Five nucleotide sequences adjacent to the sites of integration of papilloma virus in human genome and expressed in the cells of cervical cancer involved localized. It is demonstrated that the region 13q14.3-q21.1 was enriched with nucleotide sequences involved in the processes of carcinogenesis. RH mapping can be considered as one of the most perspective applications of modern radiation biology in the field of molecular genetics, that is, in constructing physical maps of mammalian genomes with high resolution level [ru

3ircular dichroism simulation shows a site-II-to-site-I displacement of human serum albumin-bound diclofenac by ibuprofen

OpenAIRE

Yamasaki, Keishi; Rahman, Mohammed Hablbur; Tsutsumi, Yasuhiro; Maruyama, Toru; Ahmed, Shamim; Kragh-Hansen; Otagiri, Masaki

2000-01-01

Purpose: The purpose of this study was to confirm the hypothesis that a site-II-to-site-I displacement takes place when some nonsteroidal anti-inflammatory drugs are displaced by another drug from their high-affinity binding site to a site of lower affinity on human serum albumin (HSA).Methods: Diclofenac, sodium salt, was used as a representative example because of its prominent reversal of the Cotton effect. Effects of site-specific drugs on the free fraction of diclofenac were determined b...

A terrain-based site characterization map of California with implications for the contiguous United States

Science.gov (United States)

Yong, Alan K.; Hough, Susan E.; Iwahashi, Junko; Braverman, Amy

2012-01-01

We present an approach based on geomorphometry to predict material properties and characterize site conditions using the VS30 parameter (time‐averaged shear‐wave velocity to a depth of 30 m). Our framework consists of an automated terrain classification scheme based on taxonomic criteria (slope gradient, local convexity, and surface texture) that systematically identifies 16 terrain types from 1‐km spatial resolution (30 arcsec) Shuttle Radar Topography Mission digital elevation models (SRTM DEMs). Using 853 VS30 values from California, we apply a simulation‐based statistical method to determine the mean VS30 for each terrain type in California. We then compare the VS30 values with models based on individual proxies, such as mapped surface geology and topographic slope, and show that our systematic terrain‐based approach consistently performs better than semiempirical estimates based on individual proxies. To further evaluate our model, we apply our California‐based estimates to terrains of the contiguous United States. Comparisons of our estimates with 325 VS30 measurements outside of California, as well as estimates based on the topographic slope model, indicate our method to be statistically robust and more accurate. Our approach thus provides an objective and robust method for extending estimates of VS30 for regions where in situ measurements are sparse or not readily available.

Map showing thickness of saturated Quaternary deposits, Sugar House quadrangle, Salt Lake County, Utah, February 1972

Science.gov (United States)

Mower, R.W.

1973-01-01

Saturated Quaternary deposits in the Sugar Horse quadrangle supply significant quantities of water to wells from which water is withdrawn for domestic, municipal, industrial, and irrigation uses. The deposits consist of clay, silt, sand, and gravel; individual beds range from a few inches to several tens of feet thick. The principal aquifer, which is almost completely within the Quaternary deposits, supplied about 4 percent, or 9,000 acre-feet, of the municipal and industrial water used annually in Salt Lake County during 1964-68.As a general rule, more water is stored and more water will be yielded to a well where aquifers are thicker. This map can be used as a general guide to those areas where greatest amounts of water are stored in the aquifer, and where yields to wells may be greater. Local variations in the ability of saturated deposits to transmit water can alter the general relationship between aquifer thickness and yield of wells.The thickness of saturated Quaternary deposits within the area of the Sugar Horse quadrangle ranges from zero to about 650 feet, as shown on the map. The thickest section of these deposits is near the southwestern corner of the quadrangle, and the thinnest section is along the mountain front adjacent to the approximate eastern limit of saturated Quaternary deposits.The thickness of saturated Quaternary deposits shown on this map is based on drillers’ logs for 55 deep wells (which show the thickness of the Quaternary deposits) and on water-level measurements made in February 1972 in wells in unconfined shallow aquifers.Reports in the following list of selected references contain other information about the saturated Quaternary deposits in this and adjacent parts of Jordan Valley, Utah. The basic-data reports and releases contain well logs, water-level measurements, and other types of basic ground-water data. The interpretive repots contain discussions of the occurrence of ground water, tests to determine hydraulic properties of

LANDSAFE: LANDING SITE RISK ANALYSIS SOFTWARE FRAMEWORK

Directory of Open Access Journals (Sweden)

R. Schmidt

2012-08-01

Full Text Available The European Space Agency (ESA is planning a Lunar Lander mission in the 2018 timeframe that will demonstrate precise soft landing at the polar regions of the Moon. To ensure a safe and successful landing a careful risk analysis has to be carried out. This is comprised of identifying favorable target areas and evaluating the surface conditions in these areas. Features like craters, boulders, steep slopes, rough surfaces and shadow areas have to be identified in order to assess the risk associated to a landing site in terms of a successful touchdown and subsequent surface operation of the lander. In addition, global illumination conditions at the landing site have to be simulated and analyzed. The Landing Site Risk Analysis software framework (LandSAfe is a system for the analysis, selection and certification of safe landing sites on the lunar surface. LandSAfe generates several data products including high resolution digital terrain models (DTMs, hazard maps, illumination maps, temperature maps and surface reflectance maps which assist the user in evaluating potential landing site candidates. This paper presents the LandSAfe system and describes the methods and products of the different modules. For one candidate landing site on the rim of Shackleton crater at the south pole of the Moon a high resolution DTM is showcased.

A GIS-BASED MULTI-CRITERIA EVALUATION SYSTEM FOR SELECTION OF LANDFILL SITES: a case study from Abu Dhabi, United Arab Emirates

Directory of Open Access Journals (Sweden)

S. M. Issa

2012-07-01

Full Text Available Landfill sites receive 92% of total annual solid waste produced by municipalities in the emirate of Abu Dhabi. In this study, candidate sites for an appropriate landfill location for the Abu Dhabi municipal area are determined by integrating geographic information systems (GIS and multi-criteria evaluation (MCE analysis. To identify appropriate landfill sites, eight input map layers including proximity to urban areas, proximity to wells and water table depth, geology and topography, proximity to touristic and archeological sites, distance from roads network, distance from drainage networks, and land slope are used in constraint mapping. A final map was generated which identified potential areas showing suitability for the location of the landfill site. Results revealed that 30% of the study area was identified as highly suitable, 25% as suitable, and 45% as unsuitable. The selection of the final landfill site, however, requires further field research.

THE DOCUMENTATION OF HISTORIC MAPS OF WORLD HERITAGE SITE CITY SUZHOU

Directory of Open Access Journals (Sweden)

Z. Guangwei

2013-07-01

Full Text Available Documentation and analysis of historic maps enhance understanding of temporal and spatial interactions between events and the evolution of physical canals upon which they occurred. And the challenge of this work lies on carefully sifting of information through the maps drawn with relative accuracy by traditional cartographical principles before the emergence of scientific survey. This research project focuses on sorting out the evolution of historic city Suzhou in a spatio-temporal view. The investigation was conducted through an in-depth analysis of historic maps. Re-projection of the geographical elements of the city to one single georeference, that is to say a standard map BASE, help acquiring an actual sense of the scale and facilitate the recognition of the city's evolution in clear details. It is an important contribution of this thesis in coordination of variously distorted geographical information contained in nineteen periods span from 1229 to 2013 into a single research resource. Through the work both quantitative and qualitative, a clear vision of the evolution and characteristics of the urban structure of ancient Suzhou is achieved. Meanwhile, in the process of projecting the historical geometrical information onto the topographic map, historical bibliographic and cartographic records is key to the data coordination and readjustment, this inspire as well on the cautious utilization of historical materials from ancient time in the recording, documentation work.

Stepwise magnetic-geochemical approach for efficient assessment of heavy metal polluted sites

Science.gov (United States)

Appel, E.; Rösler, W.; Ojha, G.

2012-04-01

Previous studies have shown that magnetometry can outline the distribution of fly ash deposition in the surroundings of coal-burning power plants and steel industries. Especially the easy-to-measure magnetic susceptibility (MS) is capable to act as a proxy for heavy metal (HM) pollution caused by such kind of point source pollution. Here we present a demonstration project around the coal-burning power plant complex "Schwarze Pumpe" in eastern Germany. Before reunification of West and East Germany huge amounts of HM pollutants were emitted from the "Schwarze Pumpe" into the environment by both fly ash emission and dumped clinker. The project has been conducted as part of the TASK Centre of Competence which aims at bringing new innovative techniques closer to the market. Our project combines in situ and laboratory MS measurements and HM analyses in order to demonstrate the efficiency of a stepwise approach for site assessment of HM pollution around point sources of fly-ash emission and deposition into soil. The following scenario is played through: We assume that the "true" spatial distribution of HM pollution (given by the pollution load index PLI comprising Fe, Zn, Pb, and Cu) is represented by our entire set of 85 measured samples (XRF analyses) from forest sites around the "Schwarze Pumpe". Surface MS data (collected with a Bartington MS2D) and in situ vertical MS sections (logged by an SM400 instrument) are used to determine a qualitative overview of potentially higher and lower polluted areas. A suite of spatial HM distribution maps obtained by random selections of 30 out of the 85 analysed sites is compared to the HM map obtained from a targeted 30-sites-selection based on pre-information from the MS results. The PLI distribution map obtained from the targeted 30-sites-selection shows all essential details of the "true" pollution map, while the different random 30-sites-selections miss important features. This comparison shows that, for the same cost

Geological mapping of investigation trench OL-TK9 at the Olkiluoto study site, Eurajoki, SW Finland

International Nuclear Information System (INIS)

Nordbaeck, N.; Talikka, M.

2006-07-01

Geological mapping of trench OL-TK9 was carried out the by the Geological Survey of Finland at the Olkiluoto study site, Eurajoki, southwestern Finland, as a part of Posiva Oy's site investigation programme for the development of an underground repository for nuclear waste. The NW-SE striking trench, which is about 371 metres in length and 0.4-2.5 metres in width, is situated to the west from the OL-TK3 in the northwestern part of the study site. The rock types were determined macroscopically and the main rock types were further investigated microscopically. On the basis of the migmatite structure, the migmatitic gneisses at Olkiluoto can be divided into three groups: veined gneiss, stromatic gneiss and diatexitic gneiss. Most of the migmatitic gneisses in the trench are veined gneisses and only a few short sections of the diatexitic gneiss or K-feldspar porphyry exist. Stromatic gneisses were not encountered. The leucosome of the veined gneiss show vein like, more or less linear traces with some features similar to large-scale augen structures, whereas the migmatitic structure of the diatexitic gneiss is more asymmetric and irregular. The southernmost part of the trench is dominated by mica gneiss and pegmatitic granite. The mica gneiss is homogenous mica-rich rock that contains less than 10 % granite leucosome material. The pegmatitic granite shows variations in grain size, colour, and mode of occurrence. The veined gneiss dominates the central part of the trench. The northernmost part of the trench is mainly comprised of tonalitic-granodioritic-granitic gneiss, which has an igneous character. Most rocks in the trench are altered, the intensity of the alteration varies from weak to strong, and the most common alteration type is chloritisation. The intense alteration has resulted in pervasive softening and weathering of the bedrock in places and up to four meters thick layers of strongly weathered rocks were observed on the edges of the trench. The foliation S2B

Electrocorticographic Temporal Alteration Mapping: A Clinical Technique for Mapping the Motor Cortex with Movement-Related Cortical Potentials

Directory of Open Access Journals (Sweden)

Zehan Wu

2017-06-01

Full Text Available We propose electrocorticographic temporal alteration mapping (ETAM for motor cortex mapping by utilizing movement-related cortical potentials (MRCPs within the low-frequency band [0.05-3] Hz. This MRCP waveform-based temporal domain approach was compared with the state-of-the-art electrocorticographic frequency alteration mapping (EFAM, which is based on frequency spectrum dynamics. Five patients (two epilepsy cases and three tumor cases were enrolled in the study. Each patient underwent intraoperative direct electrocortical stimulation (DECS procedure for motor cortex localization. Moreover, the patients were required to perform simple brisk wrist extension task during awake craniotomy surgery. Cross-validation results showed that the proposed ETAM method had high sensitivity (81.8% and specificity (94.3% in identifying sites which exhibited positive DECS motor responses. Moreover, although the sensitivity of the ETAM and EFAM approaches was not significantly different, ETAM had greater specificity compared with EFAM (94.3 vs. 86.1%. These results indicate that for the intraoperative functional brain mapping, ETAM is a promising novel approach for motor cortex localization with the potential to reduce the need for cortical electrical stimulation.

Integrating Radar Image Data with Google Maps

Science.gov (United States)

Chapman, Bruce D.; Gibas, Sarah

2010-01-01

A public Web site has been developed as a method for displaying the multitude of radar imagery collected by NASA s Airborne Synthetic Aperture Radar (AIRSAR) instrument during its 16-year mission. Utilizing NASA s internal AIRSAR site, the new Web site features more sophisticated visualization tools that enable the general public to have access to these images. The site was originally maintained at NASA on six computers: one that held the Oracle database, two that took care of the software for the interactive map, and three that were for the Web site itself. Several tasks were involved in moving this complicated setup to just one computer. First, the AIRSAR database was migrated from Oracle to MySQL. Then the back-end of the AIRSAR Web site was updated in order to access the MySQL database. To do this, a few of the scripts needed to be modified; specifically three Perl scripts that query that database. The database connections were then updated from Oracle to MySQL, numerous syntax errors were corrected, and a query was implemented that replaced one of the stored Oracle procedures. Lastly, the interactive map was designed, implemented, and tested so that users could easily browse and access the radar imagery through the Google Maps interface.

Using a Similarity Matrix Approach to Evaluate the Accuracy of Rescaled Maps

Directory of Open Access Journals (Sweden)

Peijun Sun

2018-03-01

Full Text Available Rescaled maps have been extensively utilized to provide data at the appropriate spatial resolution for use in various Earth science models. However, a simple and easy way to evaluate these rescaled maps has not been developed. We propose a similarity matrix approach using a contingency table to compute three measures: overall similarity (OS, omission error (OE, and commission error (CE to evaluate the rescaled maps. The Majority Rule Based aggregation (MRB method was employed to produce the upscaled maps to demonstrate this approach. In addition, previously created, coarser resolution land cover maps from other research projects were also available for comparison. The question of which is better, a map initially produced at coarse resolution or a fine resolution map rescaled to a coarse resolution, has not been quantitatively investigated. To address these issues, we selected study sites at three different extent levels. First, we selected twelve regions covering the continental USA, then we selected nine states (from the whole continental USA, and finally we selected nine Agriculture Statistical Districts (ASDs (from within the nine selected states as study sites. Crop/non-crop maps derived from the USDA Crop Data Layer (CDL at 30 m as base maps were used for the upscaling and existing maps at 250 m and 1 km were utilized for the comparison. The results showed that a similarity matrix can effectively provide the map user with the information needed to assess the rescaling. Additionally, the upscaled maps can provide higher accuracy and better represent landscape pattern compared to the existing coarser maps. Therefore, we strongly recommend that an evaluation of the upscaled map and the existing coarser resolution map using a similarity matrix should be conducted before deciding which dataset to use for the modelling. Overall, extending our understanding on how to perform an evaluation of the rescaled map and investigation of the applicability

FeatureMap3D - a tool to map protein features and sequence conservation onto homologous structures in the PDB

DEFF Research Database (Denmark)

Wernersson, Rasmus; Rapacki, Krzysztof; Stærfeldt, Hans Henrik

2006-01-01

FeatureMap3D is a web-based tool that maps protein features onto 3D structures. The user provides sequences annotated with any feature of interest, such as post-translational modifications, protease cleavage sites or exonic structure and FeatureMap3D will then search the Protein Data Bank (PDB) f...

Probabilistic and Scenario Seismic and Liquefaction Hazard Analysis of the Mississippi Embayment Incorporating Nonlinear Site Effects

Science.gov (United States)

Cramer, C. H.; Dhar, M. S.

2017-12-01

The influence of deep sediment deposits of the Mississippi Embayment (ME) on the propagation of seismic waves is poorly understood and remains a major source of uncertainty for site response analysis. Many researchers have studied the effects of these deposits on seismic hazard of the area using available information at the time. In this study, we have used updated and newly available resources for seismic and liquefaction hazard analyses of the ME. We have developed an improved 3D geological model. Additionally, we used surface geological maps from Cupples and Van Arsdale (2013) to prepare liquefaction hazard maps. Both equivalent linear and nonlinear site response codes were used to develop site amplification distributions for use in generating hazard maps. The site amplification distributions are created using the Monte Carlo approach of Cramer et al. (2004, 2006) on a 0.1-degree grid. The 2014 National Seismic Hazard model and attenuation relations (Petersen et al., 2014) are used to prepare seismic hazard maps. Then liquefaction hazard maps are generated using liquefaction probability curves from Holzer (2011) and Cramer et al. (2015). Equivalent linear response (w/ increased precision, restricted nonlinear behavior with depth) shows similar hazard for the ME compared to nonlinear analysis (w/o pore pressure) results. At short periods nonlinear deamplification dominates the hazard, but at long periods resonance amplification dominates. The liquefaction hazard tends to be high in Holocene and late Pleistocene lowland sediments, even with lowered ground water levels, and low in Pleistocene loess of the uplands. Considering pore pressure effects in nonlinear site response analysis at a test site on the lowlands shows amplification of ground motion at short periods. PGA estimates from ME liquefaction and MMI observations are in the 0.25 to 0.4 g range. Our estimated M7.5 PGA hazard within 10 km of the fault can exceed this. Ground motion observations from

Genome wide association mapping of grain arsenic, copper, molybdenum and zinc in rice (Oryza sativa L. grown at four international field sites.

Directory of Open Access Journals (Sweden)

Gareth J Norton

Full Text Available The mineral concentrations in cereals are important for human health, especially for individuals who consume a cereal subsistence diet. A number of elements, such as zinc, are required within the diet, while some elements are toxic to humans, for example arsenic. In this study we carry out genome-wide association (GWA mapping of grain concentrations of arsenic, copper, molybdenum and zinc in brown rice using an established rice diversity panel of ∼ 300 accessions and 36.9 k single nucleotide polymorphisms (SNPs. The study was performed across five environments: one field site in Bangladesh, one in China and two in the US, with one of the US sites repeated over two years. GWA mapping on the whole dataset and on separate subpopulations of rice revealed a large number of loci significantly associated with variation in grain arsenic, copper, molybdenum and zinc. Seventeen of these loci were detected in data obtained from grain cultivated in more than one field location, and six co-localise with previously identified quantitative trait loci. Additionally, a number of candidate genes for the uptake or transport of these elements were located near significantly associated SNPs (within 200 kb, the estimated global linkage disequilibrium previously employed in this rice panel. This analysis highlights a number of genomic regions and candidate genes for further analysis as well as the challenges faced when mapping environmentally-variable traits in a highly genetically structured diversity panel.

Geological mapping of investigation trench OL-TK18 at the Olkiluoto study site, Eurajoki, SW Finland

Energy Technology Data Exchange (ETDEWEB)

Engstroem, J. [GTK Geological Survey of Finland, Espoo (Finland)

2012-04-15

Survey of Finland at the Olkiluoto study site, Eurajoki, as part of Posiva Oy's site investigation programme for the development of an underground repository for nuclear waste. The E-W striking, ca. 55 m long trench is located in the central part of the Olkiluoto Island adjacent to investigation trenches OL-TK12 and OL-TK4. The trench was cleaned with a pressure washer and pressurized air. The rock types were determined macroscopically. The rock types in investigation trench OL-TK18 is of heterogeneous character, with a large variation in their composition. The rocks vary from tonalitic-granodioritic gneiss to diatexitic gneiss, with portions of K-feldspar porphyritic gneiss. Inclusions of mica gneiss and a well-preserved schollen migmatite is encountered. The trench ends in a feldspar-rich pegmatoid. The most dominant tectonic feature is D{sub 4} ductile deformation domain and associated S{sub 4} foliation. This domain and hence the S{sub 4} foliation is striking NE-SW with a moderate dip towards SE. Both ends of the trench are dominated by the earlier deformation phase, showing S{sub 3} foliation striking ENE-WSW and roughly dipping towards the S. The S{sub 3} foliation is associated with small-scaled granitic leucosome veining, while the S{sub 4} foliation have a schistose character and it is more sheared. D{sub 4} ductile deformation domain is also characterised by a sheared blastomylonitic rock having growth of roundish feldspar porphyroblasts and BTschlierens indicating high alteration of the protolith. During the fracture mapping, all fractures intersecting the central thread were investigated and a total of 117 fractures were recorded. The average fracture frequency of the trench is 2.11 fractures/m. On the basis of fracture orientations one main set can be distinguished striking NE-SW (foliation parallel) with a moderate dip towards the SE. The median fracture trace length is 1.6 m and over half of the fractures exceed 1.5 m trace length, the longest

Map showing thermal-alteration indicies in roadless areas and the Santa Lucia Wilderness in the Los Padres National Forest, Southwestern California

Science.gov (United States)

Frederiksen, N.O.

1985-01-01

This map shows thermal-alteration indices (TAI's), based on colors of pollen grains, of 115 outcrop and 20 conventional core samples from Mesozoic and lower Tertiary rocks in the southern Coast and western Transverse Ranges, Southwestern California. The TAI's have been calibrated against previously determined vitrinite reflectance values from some of the same sample localities.

Mapping of the Lassa virus LAMP1 binding site reveals unique determinants not shared by other old world arenaviruses.

Directory of Open Access Journals (Sweden)

Hadar Israeli

2017-04-01

Full Text Available Cell entry of many enveloped viruses occurs by engagement with cellular receptors, followed by internalization into endocytic compartments and pH-induced membrane fusion. A previously unnoticed step of receptor switching was found to be critical during cell entry of two devastating human pathogens: Ebola and Lassa viruses. Our recent studies revealed the functional role of receptor switching to LAMP1 for triggering membrane fusion by Lassa virus and showed the involvement of conserved histidines in this switching, suggesting that other viruses from this family may also switch to LAMP1. However, when we investigated viruses that are genetically close to Lassa virus, we discovered that they cannot bind LAMP1. A crystal structure of the receptor-binding module from Morogoro virus revealed structural differences that allowed mapping of the LAMP1 binding site to a unique set of Lassa residues not shared by other viruses in its family, illustrating a key difference in the cell-entry mechanism of Lassa virus that may contribute to its pathogenicity.

Implications of NGA for NEHRP site coefficients

Science.gov (United States)

Borcherdt, Roger D.

2012-01-01

Three proposals are provided to update tables 11.4-1 and 11.4-2 of Minimum Design Loads for Buildings and Other Structures (7-10), by the American Society of Civil Engineers (2010) (ASCE/SEI 7-10), with site coefficients implied directly by NGA (Next Generation Attenuation) ground motion prediction equations (GMPEs). Proposals include a recommendation to use straight-line interpolation to infer site coefficients at intermediate values of ̅vs (average shear velocity). Site coefficients are recommended to ensure consistency with ASCE/SEI 7-10 MCER (Maximum Considered Earthquake) seismic-design maps and simplified site-specific design spectra procedures requiring site classes with associated tabulated site coefficients and a reference site class with unity site coefficients. Recommended site coefficients are confirmed by independent observations of average site amplification coefficients inferred with respect to an average ground condition consistent with that used for the MCER maps. The NGA coefficients recommended for consideration are implied directly by the NGA GMPEs and do not require introduction of additional models.

Portable radiation detector and mapping system

International Nuclear Information System (INIS)

Hofstetter, K.J.; Hayes, D.W.; Eakle, R.F.

1995-01-01

A portable radiation detector and mapping system (RADMAPS) has been developed to detect, locate and plot nuclear radiation intensities on commercially available digital maps and other images. The field unit records gamma-ray spectra or neutron signals together with positions from a Global Positioning System (GPS) on flash memory cards. The recorded information is then transferred to a lap-top computer for spectral data analyses and then georegistered graphically on maps, photographs, etc. RADMAPS integrates several existing technologies to produce a preprogrammable field unit uniquely suited for each survey, as required. The system presently records spectra from a Nal(Tl) gamma-ray detector or an enriched Li-6 doped glass neutron scintillator. Standard Geographic Information System software installed in a lap-top, complete with CD-ROM supporting digitally imaged maps, permits the characterization of nuclear material in the field when the presence of such material is not otherwise documented. This paper gives the results of a typical site survey of the Savannah River Site (SRS) using RADMAPS

Density, Spatial Pattern and Relief Features of Sacred Sites in Northern Morocco

Directory of Open Access Journals (Sweden)

Holger Jäckle

2013-02-01

Full Text Available Sacred sites are of conservation value because of their spiritual meaning, as cultural heritage and as remnants of near-natural biotopes in landscapes strongly transformed by man. The vegetation of sacred sites in Morocco was studied recently. Information about their number, spatial pattern or relief position is fragmentary. However, these parameters are important to evaluate their role as refuge for organisms and their representativeness of potential natural vegetation. Therefore, density and spatial pattern of sacred sites on the Tangier Peninsula in NW Morocco were studied based on records on topographic maps and by ground check. Their relief position was examined calculating a logistic regression model based on site-presences and random pseudo-absences. A ground check showed that around 67% of the existing sacred sites are documented in the topographic maps. They occur in the whole study area but are agglomerated around settlements. Although sacred sites occur with preference at elevated sites they can be found in almost all relief positions, thus offering the potential of supporting different types of climax vegetation (climatic climax and pedoclimax. Because of their abundance (around 29 sacred sites / 100 km² and their distribution pattern they could serve as elements of a biotope network in degraded landscapes.

International Journal of Pedagogy, Policy and ICT in Education: Site ...

African Journals Online (AJOL)

International Journal of Pedagogy, Policy and ICT in Education: Site Map. Journal Home > About the Journal > International Journal of Pedagogy, Policy and ICT in Education: Site Map. Log in or Register to get access to full text downloads.

Site Suitability For Yam, Rice And Cotton Production In Adamawa ...

African Journals Online (AJOL)

This paper demonstrated the potentials of GIS technique for mapping and delineating the suitable sites for Yam, Rice and Cotton production in Adamawa State. Site suitability mapping is necessary to create data bank and to guide the farmers in decision making on sites for crop production in the state. The use of GIS for this ...

Over half of breakpoints in gene pairs involved in cancer-specific recurrent translocations are mapped to human chromosomal fragile sites

Directory of Open Access Journals (Sweden)

Pierce Levi CT

2009-01-01

Full Text Available Abstract Background Gene rearrangements such as chromosomal translocations have been shown to contribute to cancer development. Human chromosomal fragile sites are regions of the genome especially prone to breakage, and have been implicated in various chromosome abnormalities found in cancer. However, there has been no comprehensive and quantitative examination of the location of fragile sites in relation to all chromosomal aberrations. Results Using up-to-date databases containing all cancer-specific recurrent translocations, we have examined 444 unique pairs of genes involved in these translocations to determine the correlation of translocation breakpoints and fragile sites in the gene pairs. We found that over half (52% of translocation breakpoints in at least one gene of these gene pairs are mapped to fragile sites. Among these, we examined the DNA sequences within and flanking three randomly selected pairs of translocation-prone genes, and found that they exhibit characteristic features of fragile DNA, with frequent AT-rich flexibility islands and the potential of forming highly stable secondary structures. Conclusion Our study is the first to examine gene pairs involved in all recurrent chromosomal translocations observed in tumor cells, and to correlate the location of more than half of breakpoints to positions of known fragile sites. These results provide strong evidence to support a causative role for fragile sites in the generation of cancer-specific chromosomal rearrangements.

Genome-Wide Mapping of Growth-Related Quantitative Trait Loci in Orange-Spotted Grouper (Epinephelus coioides) Using Double Digest Restriction-Site Associated DNA Sequencing (ddRADseq).

Science.gov (United States)

Yu, Hui; You, Xinxin; Li, Jia; Liu, Hankui; Meng, Zining; Xiao, Ling; Zhang, Haifa; Lin, Hao-Ran; Zhang, Yong; Shi, Qiong

2016-04-06

Mapping of quantitative trait loci (QTL) is essential for the discovery of genetic structures that related to complex quantitative traits. In this study, we identified 264,072 raw SNPs (single-nucleotide polymorphisms) by double digest restriction site associated DNA sequencing (ddRADseq), and utilized 3029 of these SNPs to construct a genetic linkage map in orange-spotted grouper (Epinephelus coioides) using a regression mapping algorithm. The genetic map contained 24 linkage groups (LGs) spanning a total genetic distance of 1231.98 cM. Twenty-seven significant growth-related QTLs were identified. Furthermore, we identified 17 genes (fez2, alg3, ece2, arvcf, sla27a4, sgk223, camk2, prrc2b, mchr1, sardh, pappa, syk, tert, wdrcp91, ftz-f1, mate1 and notch1) including three (tert, ftz-f1 and notch1) that have been reported to be involved in fish growth. To summarize, we mapped growth-related QTLs in the orange-spotted grouper. These QTLs will be useful in marker-assisted selection (MAS) efforts to improve growth-related traits in this economically important fish.

Hyperspectral surface materials map of quadrangle 3266, Uruzgan (519) and Moqur (520) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3464, Shahrak (411) and Kasi (412) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3470, Jalalabad (511) and Chaghasaray (512) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3368, Ghazni (515) and Gardez (516) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3162, Chakhansur (603) and Kotalak (604) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3362, Shindand (415) and Tulak (416) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3366, Gizab (513) and Nawer (514) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3770, Faizabad (217) and Parkhaw (218) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3564, Jowand (405) and Gurziwan (406) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Building online brand perceptual map.

Science.gov (United States)

Chiang, I-Ping; Lin, Chih-Ying; Wang, Kaisheng M

2008-10-01

Many companies have launched their products or services online as a new business focus, but only a few of them have survived the competition and made profits. The most important key to an online business's success is to create "brand value" for the customers. Although the concept of online brand has been discussed in previous studies, there is no empirical study on the measurement of online branding. As Web 2.0 emerges to be critical to online branding, the purpose of this study was to measure Taiwan's major Web sites with a number of personality traits to build a perceptual map for online brands. A pretest identified 10 most representative online brand perceptions. The results of the correspondence analysis showed five groups in the perceptual map. This study provided a practical view of the associations and similarities among online brands for potential alliance or branding strategies. The findings also suggested that brand perceptions can be used with identified consumer needs and behaviors to better position online services. The brand perception map in the study also contributed to a better understanding of the online brands in Taiwan.

GIS and geotechnical mapping of expansive soil in Toshka region

Directory of Open Access Journals (Sweden)

Mary Labib

2013-09-01

Full Text Available This paper presents the results of a subsurface site investigation that was performed to characterize different soil and rock formations along Sheikh Zayed canal with particular emphasis on the swelling characteristics of the clays in that area. Site-specific empirical correlations were developed to predict the clay swelling potential and pressure from simple and economic laboratory test results. The data were input into a Geographic Information System (GIS framework to provide interactive maps that show the spatial distribution of the variables and identify their characteristics. These maps are then used to easily identify the values of swelling pressure/potential at various locations. This research provides a tool that is based on simple index tests that can be used to provide data that otherwise would require elaborate and costly investigations; the GIS framework allows storing, retrieving and updating these data easily to assist taking supported decisions dynamically.

Comprehensive human transcription factor binding site map for combinatory binding motifs discovery.

Directory of Open Access Journals (Sweden)

Arnoldo J Müller-Molina

Full Text Available To know the map between transcription factors (TFs and their binding sites is essential to reverse engineer the regulation process. Only about 10%-20% of the transcription factor binding motifs (TFBMs have been reported. This lack of data hinders understanding gene regulation. To address this drawback, we propose a computational method that exploits never used TF properties to discover the missing TFBMs and their sites in all human gene promoters. The method starts by predicting a dictionary of regulatory "DNA words." From this dictionary, it distills 4098 novel predictions. To disclose the crosstalk between motifs, an additional algorithm extracts TF combinatorial binding patterns creating a collection of TF regulatory syntactic rules. Using these rules, we narrowed down a list of 504 novel motifs that appear frequently in syntax patterns. We tested the predictions against 509 known motifs confirming that our system can reliably predict ab initio motifs with an accuracy of 81%-far higher than previous approaches. We found that on average, 90% of the discovered combinatorial binding patterns target at least 10 genes, suggesting that to control in an independent manner smaller gene sets, supplementary regulatory mechanisms are required. Additionally, we discovered that the new TFBMs and their combinatorial patterns convey biological meaning, targeting TFs and genes related to developmental functions. Thus, among all the possible available targets in the genome, the TFs tend to regulate other TFs and genes involved in developmental functions. We provide a comprehensive resource for regulation analysis that includes a dictionary of "DNA words," newly predicted motifs and their corresponding combinatorial patterns. Combinatorial patterns are a useful filter to discover TFBMs that play a major role in orchestrating other factors and thus, are likely to lock/unlock cellular functional clusters.

IDAS, software support for mathematical models and map-based graphics

International Nuclear Information System (INIS)

Birnbaum, M.D.; Wecker, D.B.

1984-01-01

IDAS (Intermediate Dose Assessment System) was developed for the U.S. Nuclear Regulatory Commission as a hardware/software host for radiological models and display of map-based plume graphics at the Operations Center (HQ), regional incident response centers, and site emergency facilities. IDAS design goals acknowledged the likelihood of future changes in the suite of models and the composition of map features for analysis and graphical display. IDAS provides a generalized software support environment to programmers and users of modeling programs. A database manager process provides multi-user access control to all input and output data for modeling programs. A programmer-created data description file (schema) specifies data field names, data types, legal and recommended ranges, default values, preferred units of measurement, and ''help'' text. Subroutine calls to IDAS from a model program invoke a consistent user interface which can show any of the schema contents, convert units of measurement, and route data to multiple logical devices, including the database. A stand-alone data editor allows the user to read and write model data records without execution of a model. IDAS stores digitized map features in a 4-level naming hierarchy. A user can select the map icon, color, and whether to show a stored name tag, for each map feature. The user also selects image scale (zoom) within limits set by map digitization. The resulting image combines static map information, computed analytic modeling results, and the user's feature selections for display to decision-makers

Assessment of an Operational System for Crop Type Map Production Using High Temporal and Spatial Resolution Satellite Optical Imagery

Directory of Open Access Journals (Sweden)

Jordi Inglada

2015-09-01

Full Text Available Crop area extent estimates and crop type maps provide crucial information for agricultural monitoring and management. Remote sensing imagery in general and, more specifically, high temporal and high spatial resolution data as the ones which will be available with upcoming systems, such as Sentinel-2, constitute a major asset for this kind of application. The goal of this paper is to assess to what extent state-of-the-art supervised classification methods can be applied to high resolution multi-temporal optical imagery to produce accurate crop type maps at the global scale. Five concurrent strategies for automatic crop type map production have been selected and benchmarked using SPOT4 (Take5 and Landsat 8 data over 12 test sites spread all over the globe (four in Europe, four in Africa, two in America and two in Asia. This variety of tests sites allows one to draw conclusions applicable to a wide variety of landscapes and crop systems. The results show that a random forest classifier operating on linearly temporally gap-filled images can achieve overall accuracies above 80% for most sites. Only two sites showed low performances: Madagascar due to the presence of fields smaller than the pixel size and Burkina Faso due to a mix of trees and crops in the fields. The approach is based on supervised machine learning techniques, which need in situ data collection for the training step, but the map production is fully automatic.

Direct probability mapping of contaminants

International Nuclear Information System (INIS)

Rautman, C.A.

1993-01-01

Exhaustive characterization of a contaminated site is a physical and practical impossibility. Descriptions of the nature, extent, and level of contamination, as well as decisions regarding proposed remediation activities, must be made in a state of uncertainty based upon limited physical sampling. Geostatistical simulation provides powerful tools for investigating contaminant levels, and in particular, for identifying and using the spatial interrelationships among a set of isolated sample values. This additional information can be used to assess the likelihood of encountering contamination at unsampled locations and to evaluate the risk associated with decisions to remediate or not to remediate specific regions within a site. Past operation of the DOE Feed Materials Production Center has contaminated a site near Fernald, Ohio, with natural uranium. Soil geochemical data have been collected as part of the Uranium-in-Soils Integrated Demonstration Project. These data have been used to construct a number of stochastic images of potential contamination for parcels approximately the size of a selective remediation unit. Each such image accurately reflects the actual measured sample values, and reproduces the univariate statistics and spatial character of the extant data. Post-processing of a large number of these equally likely, statistically similar images produces maps directly showing the probability of exceeding specified levels of contamination. Evaluation of the geostatistical simulations can yield maps representing the expected magnitude of the contamination for various regions and other information that may be important in determining a suitable remediation process or in sizing equipment to accomplish the restoration

High Resolution Mapping of an Alleged Chemical Weapons Dump Site in the Santa Cruz Basin, offshore California

Science.gov (United States)

Brewer, P. G.; Peltzer, E. T.; Walz, P. M.; Caress, D. W.; Thomas, H. J.

2013-12-01

Nautical charts record seven locations off the coast of California labeled as 'Chemical Munitions Dumping Area, Disused' that together cover some 12,000 km2 of sea floor. However only one such chemical munitions site is officially documented and no record exists of any chemical munitions disposed of at other locations, thus creating confusion. We have executed a one day AUV mapping survey of a corner of one such site in the Santa Cruz Basin, south of Port Hueneme, to examine and investigate the debris field. The region is covered with soft sediment and the overlying water is very low in oxygen at ~10 μmol/kg. The processed 110 kHz sidescan data revealed some 754 targets in 25.6 km2 for an average of 29 targets per km2. This was followed by two ROV dives to investigate the targets identified. We found but one false positives among the over 40 targets visited, and found items ranging from two distinct lines of unmarked or labeled and now empty barrels, two target drones, and much miscellaneous debris including 4-packs of cat food cans and a large ships mast over 30m in length. There was zero evidence of chemical weapons materiel as expected given the lack of official records. Almost all of the targets were covered in dense and colorful assemblages of invertebrates: sponges, anemones, and crabs. Where barrels were sufficiently open for full visual inspection, the interior sea floor appeared to have become fully anoxic and was covered in white and yellow bacterial mat. The area chosen for our survey (centered at 33.76 deg N 119.56 deg W) was across the north western boundary of the marked site, and represents only ~ 10% percent of the designated area. Our expectation, that human nature would drive the disposal activities to the nearest corner of the chosen area rather than the center of the field appears to have been confirmed. Objects were found both within and outside of the boundary of the dump site. We have not surveyed the full marked area but there appears to be

Farm Mapping to Assist, Protect, and Prepare Emergency Responders: Farm MAPPER.

Science.gov (United States)

Reyes, Iris; Rollins, Tami; Mahnke, Andrea; Kadolph, Christopher; Minor, Gerald; Keifer, Matthew

2014-01-01

Responders such as firefighters and emergency medical technicians who respond to farm emergencies often face complex and unknown environments. They may encounter hazards such as fuels, solvents, pesticides, caustics, and exploding gas storage cylinders. Responders may be unaware of dirt roads within the farm that can expedite their arrival at critical sites or snow-covered manure pits that act as hidden hazards. A response to a farm, unless guided by someone familiar with the operation, may present a risk to responders and post a challenge in locating the victim. This project explored the use of a Web-based farm-mapping application optimized for tablets and accessible via easily accessible on-site matrix barcodes, or quick response codes (QR codes), to provide emergency responders with hazard and resource information to agricultural operations. Secured portals were developed for both farmers and responders, allowing both parties to populate and customize farm maps with icons. Data were stored online and linked to QR codes attached to mailbox posts where emergency responders may read them with a mobile device. Mock responses were conducted on dairy farms to test QR code linking efficacy, Web site security, and field usability. Findings from farmer usability tests showed willingness to enter data as well as ease of Web site navigation and data entry even with farmers who had limited computer knowledge. Usability tests with emergency responders showed ease of QR code connectivity to the farm maps and ease of Web site navigation. Further research is needed to improve data security as well as assess the program's applicability to nonfarm environments and integration with existing emergency response systems. The next phases of this project will expand the program for regional and national use, develop QR code-linked, Web-based extrication guidance for farm machinery for victim entrapment rescue, and create QR code-linked online training videos and materials for limited

Flood-inundation maps for the St. Marys River at Decatur, Indiana

Science.gov (United States)

Strauch, Kellan R.

2015-08-24

Digital flood-inundation maps for an 8.9-mile reach of the St. Marys River at Decatur, Indiana, were developed by the U.S. Geological Survey (USGS), in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site (http://water.usgs.gov/osw/flood_inundation/), depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) of the St. Marys River at Decatur (USGS station number 04181500). The maps are useful for estimating near-real-time areas of inundation by referencing concurrent USGS streamgage information at http://waterdata.usgs.gov/. In addition, the streamgage information was provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service flood warning system (http:/water.weather.gov/ahps/). NWS-forecasted peak-stage information may be used in conjunction with the maps developed during this study to show predicted areas of flood inundation.

Results of a Musa mapping project

International Nuclear Information System (INIS)

Lagoda, P.J.L.; Noyer, J.L.; Baurens, F.C.

1998-01-01

A completed map, based on two selfed progenies from two banana cultivars (M53 and SFB5) is presented (roughly 1200 cM). More than three hundred markers are linked in 11 linkage groups representing the genome (2n=22) of Musa acuminata. Roughly one third of the markers are co-dominant restriction fragment polymorphisms (RFLPs; one hundred) or micro satellites (thirty). Two thirds of the markers are dominant amplified fragment length polymorphisms (AFLPs; 10% could be considered to be co-dominant). The mean linkage distance is 3 cM, but marker density still should be increased on a couple of linkage groups. Particularities for a mapping job in banana are discussed. Due to Musa acuminata sub-species specific translocations, up to 36% of all the markers tested show important segregation distortions. The need for a cooperative mapping initiative based on a proposed ''frame-map'' harbouring evenly spaced co-dominant ''anchor'' markers is proposed. CIRAD has published 45 sequence tagged micro satellite sites (STMS) in the EMBL database which are accessible at: ''http://www.ebi.ac.uk/'' using the keywords LAGODA and MICROSATELLITE (EMBL accessions X87258 to X87265, X90740 to X90750 and Z85950 to Z85977). (author)

GPS-based handheld device for mapping contaminated areas

International Nuclear Information System (INIS)

Paridaens, J.

2005-01-01

Sometimes one is confronted with the challenge to map large areas with enhanced radioactivity. Examples are mine tailings or waste rock piles, deposits of the phosphate industry, flooding zones contaminated by effluents of plants processing ores containing enhanced natural radiation, nuclear accident sites etc. Car borne measuring equipment is not always an option, as the terrain might be rough and only accessible by foot. Airborne mapping with helicopters on the other hand is fast, but expensive, not readily available, shows difficulties with complex topography and lacks the necessary detail. The objective of this study was to create a portable and easily usable tool for the real time logging of radiation and location data, allowing mapping the radioactivity by simply walking over any kind of terrain with the portable equipment and post processing the data in the office. We also assessed the performance of the GPS based system on contaminated sites with areas varying from less than a hectare to several tens of hectares, with respect to speed, precision and ease of use. At sites of large scale mining and processing of uranium ore, tailings and waste rock piles are today the most visible relics of the uranium extractive industry. These mining relics are constantly subjected to weathering and leaching processes causing the dissemination of radioactive and toxic elements and sometimes requiring remedial operations. The in situ remediation of waste rock piles usually includes their revegetation for minimizing the water infiltration and for increasing surface soil stability. Thanks to its biomass density and longevity, the perennial vegetation plays an important role in stabilisation of the water cycling. The buffer role of forest vegetation can reduce water export from watersheds as well as erosion and hydrological losses of chemicals including radionuclides from contaminated sites. If long term reduction of contaminant dispersion at revegetated uranium mining sites is

Restriction map of the single-stranded DNA genome of Kilham rat virus strain 171, a nondefective parvovirus

International Nuclear Information System (INIS)

Banerjee, P.T.; Rathrock, R.; Mitra, S.

1981-01-01

A physical map of Kilham rat virus strain 171 DNA was constructed by analyzing the sizes and locations of restriction endonuclease-generated fragments of the replicative-form viral DNA synthesized in vitro. BglI, KpnI, BamHI, SmaI, XhoI, and XorII did not appear to have any cleavage sites, whereas 11 other enzymes cleaved the genome at one to eight sites, and AluI generated more than 12 distinct fragments. The 30 restriction sites that were mapped were distributed randomly in the viral genome. A comparison of the restriction fragments of in vivo- and in vitro-replicated replicative-form DNAs showed that these DNAs were identical except in the size or configuration of the terminal fragments

Mapping Unknown Knowns

DEFF Research Database (Denmark)

Diogo de Andrade Silva, Elisa; Lanng, Ditte Bendix; Wind, Simon

representative dimensions of travellers’ embodied ‘dwelling-in-motion’ (Urry, 2007) and experiences. The paper foregrounds a ‘Mapping-in-Motion’ graphic example, an experimental urban design student assignment aiming to map some of the less representative dimensions of journeys between A and B in Berlin...... in relation to analysis, representation, exploration and design of everyday travelling in the city. Such ‘mobilities design’ (Jensen and Lanng 2017) concerns routes, sites and artefacts of mobilities, e.g., road networks, train stations, and bike parking facilities. Some dimensions of these structures...

Source, propagation and site effects: impact on mapping strong ground motion in Bucharest area

International Nuclear Information System (INIS)

Radulian, R.; Kuznetsov, I.; Panza, G.F.

2004-01-01

Achievements in the framework of the NATO SfP project 972266 focused on the impact of Vrancea earthquakes on the security of Bucharest urban area are presented. The problem of Bucharest city security to Vrancea earthquakes is discussed in terms of numerical modelling of seismic motion and intermediate term earthquake prediction. A hybrid numerical scheme developed by Faeh et al. (1990; 1993) for frequencies up to 1 Hz is applied for the realistic modelling of the seismic ground motion in Bucharest. The method combines the modal summation for the 1D bedrock model and the finite differences for the 2D local structure model. All the factors controlling the ground motion at the site are considered: source, propagation and site effects, respectively. The input data includes the recent records provided by the digital accelerometer network developed within the Romanian-German CRC461 cooperation programme and CALIXTO'99, VRANCEA'99, VRANCEA2001 experiments. The numerical simulation proves to be a powerful tool in mapping the strong ground motion for realistic structures, reproducing acceptably from engineering point of view the observations. A new model of the Vrancea earthquake scaling is obtained and implications for the determination of the seismic motion parameters are analyzed. The role of the focal mechanism and attenuation properties upon the amplitude and spectral content of the ground motion are outlined. CN algorithm is applied for predicting Vrancea earthquakes. Finally, implications for the disaster management strategy are discussed. (authors)

A molecular map of CQR in Mali

Science.gov (United States)

Djimde, Abdoulaye A.; Barger, Breanna; Kone, Aminatou; Beavogui, Abdoul H.; Tekete, Mamadou; Fofana, Bakary; Dara, Antoine; Maiga, Hamma; Dembele, Demba; Toure, Sekou; Dama, Souleymane; Ouologuem, Dinkorma; Sangare, Cheick Papa Oumar; Dolo, Amagana; Sogoba, Nofomo; Nimaga, Karamoko; Kone, Yacouba; Doumbo, Ogobara K.

2009-01-01

Plasmodium falciparum CQR transporter point mutation (PfCRT76T) is known to be the key determinant of CQR. Molecular detection of PfCRT76T in field samples may be used for the surveillance of CQR in the malaria endemic countries. The genotype-resistance index (GRI) which is obtained as the ratio of the prevalence of PfCRT 76T to the incidence of CQR in a clinical trial was proposed as a simple andpractical molecular-based addition to the tools currently available for monitoring CQR in the field. In order to validate the GRI model across populations, time, and resistance patterns, we compiled data from the literature and generated new data from a dozen of sites across Mali. We found a mean PfCRT76T mutation prevalence of 84.5% (range 60.9%–95.1%) across all sites. CQR rates predicted from the GRI model was extrapolated onto a map of Mali to show the patterns of resistance throughout the participating regions. We present a comprehensive map of CQR in Mali, which strongly supports recent changes in drug policy away from chloroquine. PMID:20041947

International Map Year: Results and Implications

Science.gov (United States)

Rystedt, Bengt; Ormeling, Ferjan; Buckley, Aileen; Coetzee, Serena; Voženilek, Vit; Fairbairn, David; Kagawa, Ayako

2018-05-01

IMY was a worldwide celebration of maps and their unique role in our world. Supported by the United Nations, IMY provides opportunities to demonstrate, follow, and get involved in the art, science, and technology of making and using maps and geographic information. International Map Year (IMY) started in Paris 2011 when the General Assembly of the International Cartographic Association (ICA) asked the ICA Executive Committee (EC) to follow up on the proposal given in a motion from the Swedish Cartographic Society. An IMY Working Group (WG) was constituted - it defined the IMY goals and the activities required to reach them, and it proposed a suitable time period for the IMY to the ICA EC. IMY commenced in August 2015 and ended in December 2016. The success of IMY was dependent on all member nations of the ICA participating in an effort to broaden the knowledge of cartography and geographic information in society in general, especially among citizens and school children. Member nations of the ICA were responsible for organizing IMY activities, such as a national Map Day, through national IMY committees tasked to engage national organizations and spearheading collaboration. The IMY WG set up an IMY web site with general information on IMY, guidelines for how to organize Map Days, suggestions relating to activities aimed at general map awareness, and more. The web site also provides access to the electronic book The World of Maps, which has been translated from English into five other languages.

Evaluation of a Single-Beam Sonar System to Map Seagrass at Two Sites in Northern Puget Sound, Washington

Science.gov (United States)

Stevens, Andrew W.; Lacy, Jessica R.; Finlayson, David P.; Gelfenbaum, Guy

2008-01-01

Seagrass at two sites in northern Puget Sound, Possession Point and nearby Browns Bay, was mapped using both a single-beam sonar and underwater video camera. The acoustic and underwater video data were compared to evaluate the accuracy of acoustic estimates of seagrass cover. The accuracy of the acoustic method was calculated for three classifications of seagrass observed in underwater video: bare (no seagrass), patchy seagrass, and continuous seagrass. Acoustic and underwater video methods agreed in 92 percent and 74 percent of observations made in bare and continuous areas, respectively. However, in patchy seagrass, the agreement between acoustic and underwater video was poor (43 percent). The poor agreement between the two methods in areas with patchy seagrass is likely because the two instruments were not precisely colocated. The distribution of seagrass at the two sites differed both in overall percent vegetated and in the distribution of percent cover versus depth. On the basis of acoustic data, seagrass inhabited 0.29 km2 (19 percent of total area) at Possession Point and 0.043 km2 (5 percent of total area) at the Browns Bay study site. The depth distribution at the two sites was markedly different. Whereas the majority of seagrass at Possession Point occurred between -0.5 and -1.5 m MLLW, most seagrass at Browns Bay occurred at a greater depth, between -2.25 and -3.5 m MLLW. Further investigation of the anthropogenic and natural factors causing these differences in distribution is needed.

Use of electromagnetic terrain conductivity measurements to map liquid hazardous waste migration in groundwater

International Nuclear Information System (INIS)

Ketelle, R.H.; Pin, F.G.

1983-11-01

Electromagnetic conductivity measurements have been used to map apparent ground conductivity in the vicinity of a liquid hazardous waste disposal site. An area of approximately 12 ha (30 acres) was surveyed. Approximately 600 conductivity measurements were obtained to prepare a conductivity map of the site. Conductivity measurments in the area correlate with specific conductance measurements of surface and groundwater samples. Contouring of the conductivity data showed the precise location of contaminant migration pathways in the subsurface. A complex contaminant plume was defined by the conductivity survey. Conductivity values obtained reflected anisotropic characteristics related to local bedrock structure. Anisotropy characteristics and the use of different instrument configurations indicated semiquantitatively the depth of the high conductivity zone and the direction of flow

More 'mapping' in brain mapping: statistical comparison of effects

DEFF Research Database (Denmark)

Jernigan, Terry Lynne; Gamst, Anthony C.; Fennema-Notestine, Christine

2003-01-01

The term 'mapping' in the context of brain imaging conveys to most the concept of localization; that is, a brain map is meant to reveal a relationship between some condition or parameter and specific sites within the brain. However, in reality, conventional voxel-based maps of brain function......, or for that matter of brain structure, are generally constructed using analyses that yield no basis for inferences regarding the spatial nonuniformity of the effects. In the normal analysis path for functional images, for example, there is nowhere a statistical comparison of the observed effect in any voxel relative...... to that in any other voxel. Under these circumstances, strictly speaking, the presence of significant activation serves as a legitimate basis only for inferences about the brain as a unit. In their discussion of results, investigators rarely are content to confirm the brain's role, and instead generally prefer...

Joomla! Start to Finish How to Plan, Execute, and Maintain Your Web Site

CERN Document Server

Kramer, Jen

2010-01-01

There is much more to building a great web site than just downloading and installing Joomla!. This book provides crucial content on planning the website, before launching into the technology steps. It will show the reader how to analyze the client company's strategy and how to find out how the organization wants itself reflected and supported by the web site. Then it will cover the right technological solutions to the problems and getting the site structure organized via a site map.  All of this is done before you establish hosting or install Joomla!. Once the technology steps are established,

SPECIALIZED MAPPING OF CRUSTAL FAULT ZONES. PART 2: MAIN STAGES AND PROSPECTS

Directory of Open Access Journals (Sweden)

K. Zh. Seminsky

2015-01-01

Full Text Available The article is to complete the description of the special mapping method which theoretical basis and principles were published in [Seminsky, 2014]. With reference to data on the Ulirba site located in Priolkhonie (Western Pribaikalie, the content of special mapping is reviewed in detail. The method is based on paragenetical analysis of abundant jointing which specific feature is the lack of any visible displacement indicators. There are three stages in the special mapping method (Fig. 3 as follows:Stage I: Preparation and analysis of previously published data on the regional fault structure (Fig. 1, А–Г, establishment of a networks of stations to conduct structural geological monitoring and mass measurements of joints, re­cord of rock data (Fig. 2, А, general state of the fault network (Fig. 1, Д–З, fracture density (Fig. 2, Б and, if any, structures of the above-jointing level (Fig. 1, Е, З; Fig. 2, А.Stage II is aimed at processing of field data and includes activities in four groups (II.1–II.4 as follows: Group II.1: construction of circle diagrams, specification of characteristics of joint systems and their typical scatters (Fig. 4, А, identification of simple (generally tipple paragenesises, and determination of dynamic settings of their formation (translocal rank (Table 1, evaluation of densities and complexity of the joint networks, analysis of their spacial patterns within the site under mapping, and identification of the most intensively destructed zones in the rock massif (Fig. 2, Б–В. Group II.2: comparison of jointing diagrams with reference ones showing joint poles (Fig. 4, Б–В; Е–З; Л–Н, and, in case of their satisfactory correlation, making a conclusion of potential formation of a specific joint pattern in the local zone of strike-slip, normal faulting or reverse faulting (Fig. 4,  Г–Д, И–К, О–П; Fig. 5; Fig. 7, Б, and determination of relative age relationships between such zones on

Spectral signature selection for mapping unvegetated soils

Science.gov (United States)

May, G. A.; Petersen, G. W.

1975-01-01

Airborne multispectral scanner data covering the wavelength interval from 0.40-2.60 microns were collected at an altitude of 1000 m above the terrain in southeastern Pennsylvania. Uniform training areas were selected within three sites from this flightline. Soil samples were collected from each site and a procedure developed to allow assignment of scan line and element number from the multispectral scanner data to each sampling location. These soil samples were analyzed on a spectrophotometer and laboratory spectral signatures were derived. After correcting for solar radiation and atmospheric attenuation, the laboratory signatures were compared to the spectral signatures derived from these same soils using multispectral scanner data. Both signatures were used in supervised and unsupervised classification routines. Computer-generated maps using the laboratory and multispectral scanner derived signatures resulted in maps that were similar to maps resulting from field surveys. Approximately 90% agreement was obtained between classification maps produced using multispectral scanner derived signatures and laboratory derived signatures.

Mapping Substance P Binding Sites on the Neurokinin-1 Receptor Using Genetic Incorporation of a Photoreactive Amino Acid

DEFF Research Database (Denmark)

Valentin-Hansen, Louise; Park, Minyoung; Huber, Thomas

2014-01-01

that the binding site for SP includes multiple domains in the N-terminal (Nt) segment and the second extracellular loop (ECLII) of NK1. To map precisely the NK1 residues that interact with SP, we applied a novel receptor-based targeted photocross-linking approach. We used amber codon suppression to introduce...... the photoreactive unnatural amino acid p-benzoyl-l-phenylalanine (BzF) at 11 selected individual positions in the Nt tail (residues 11-21) and 23 positions in the ECLII (residues 170(C-10)-193(C+13)) of NK1. The 34 NK1 variants were expressed in mammalian HEK293 cells and retained the ability to interact...

Repeated mapping of cortical language sites by preoperative navigated transcranial magnetic stimulation compared to repeated intraoperative DCS mapping in awake craniotomy

Science.gov (United States)

2014-01-01

Background Repetitive navigated transcranial magnetic stimulation (rTMS) was recently described for mapping of human language areas. However, its capability of detecting language plasticity in brain tumor patients was not proven up to now. Thus, this study was designed to evaluate such data in order to compare rTMS language mapping to language mapping during repeated awake surgery during follow-up in patients suffering from language-eloquent gliomas. Methods Three right-handed patients with left-sided gliomas (2 opercular glioblastomas, 1 astrocytoma WHO grade III of the angular gyrus) underwent preoperative language mapping by rTMS as well as intraoperative language mapping provided via direct cortical stimulation (DCS) for initial as well as for repeated Resection 7, 10, and 15 months later. Results Overall, preoperative rTMS was able to elicit clear language errors in all mappings. A good correlation between initial rTMS and DCS results was observed. As a consequence of brain plasticity, initial DCS and rTMS findings only corresponded with the results obtained during the second examination in one out of three patients thus suggesting changes of language organization in two of our three patients. Conclusions This report points out the usefulness but also the limitations of preoperative rTMS language mapping to detect plastic changes in language function or for long-term follow-up prior to DCS even in recurrent gliomas. However, DCS still has to be regarded as gold standard. PMID:24479694

Ecological Mapping for the Preventive Conservation of Prehistoric Mural Paintings in Rock Habitats: the Site of Filiano (Basilicata, Italy

Directory of Open Access Journals (Sweden)

Giulia Caneva

2017-06-01

Full Text Available Biodeterioration phenomena are of great relevance in rock settlements, due to favourable environmental conditions, such as the infiltration of rainwaters, condensation phenomena and abundance of salts and organic nutrients. Rinaldi’s rock shelter in Filiano, which is located in a natural forest of mixed oaks is of great value due to the important traces of prehistoric paintings. It is an emblematic case of the delicate balance, achieved throughout the centuries, between the environment and artwork. During the plurimillenarian history of the site, a portion of the ceiling that covered the shelter collapsed, leaving signs that are still visible today, together with traces of blackening left by the fires of ancient settlements. Several of the biodeteriogens typical of rocky habitats have already been detected and include algae, cyanobacteria, mosses, lichens, vascular plants and fungi, which form macroscopic communities.Each community has an ecological preference and the mapping of their distribution is a suitable tool for understanding variations in the environmental factors that most affect them. Relating ecological data to the taxonomical characterization of the species and to the spatial distribution of each community, a site map of the humidity and of the nutrients was obtained. Among the various communities, microcolonial fungi (MCF, which appear as little black spots, here, represent the most critical risk factor, due to their low water needs. An evaluation of the biological risk for the possible future attack of such a biological community was made, suggesting indirect mitigation measures, through modification of the microclimatic and local ventilation conditions.

Ecocity mapping using GIS: introducing a planning method for assessing and improving neighborhood vitality.

Science.gov (United States)

Smith, Richard; Miller, Kirstin

2013-01-01

Assessing neighborhood vitality is important to understanding how to improve quality of life and health outcomes. The ecocity model recognizes that cities are part of natural systems and favors walkable neighborhoods. This article introduces ecocity mapping, an innovative planning method, to the public health literature on community engagement by describing a pilot project with a new affordable housing development in Oakland, California between 2007 and 2009. Although ecocity mapping began as a paper technology, advances in geographic information systems (GIS) moved it forward. This article describes how Ecocity Builders used GIS to conduct ecocity mapping to (1) assess vitality of neighborhoods and urban centers to prioritize community health intervention pilot sites and (2) create scenario maps for use in community health planning. From fall 2007 to summer 2008, Ecocity Builders assessed neighborhood vitality using walking distance from parks, schools, rapid transit stops, grocery stores, and retail outlets. In 2008, ecocity maps were shared with residents to create a neighborhood health and sustainability plan. In 2009, Ecocity Builders developed scenario maps to show how changes to the built environment would improve air quality by reducing greenhouse gas emissions from vehicles, while increasing access to basic services and natural amenities. Community organizing with GIS was more useful than GIS alone for final site selection. GIS was useful in mapping scenarios after residents shared local neighborhood knowledge and ideas for change. Residents were interested in long-term environmental planning, provided they could meet immediate needs.

MBARI Mapping AUV: A High-Resolution Deep Ocean Seafloor Mapping Capability

Science.gov (United States)

Caress, D. W.; Kirkwood, W. J.; Thomas, H.; McEwen, R.; Henthorn, R.; McGill, P.; Thompson, D.; Sibenac, M.; Jensen, S.; Shane, F.; Hamilton, A.

2005-05-01

The Monterey Bay Aquarium Research Institute (MBARI) is developing an autonomous seafloor mapping capability for deep ocean science applications. The MBARI Mapping AUV is a 0.53 m (21 in) diameter, 5.1 m (16.7 ft) long, Dorado-class vehicle designed to carry four mapping sonars. The primary sensor is a 200 kHz multibeam sonar producing swath bathymetry and sidescan. In addition, the vehicle carries 100 kHz and 410 kHz chirp sidescan sonars, and a 2-16 kHz sweep chirp subbottom profiler. Navigation and attitude data are obtained from an inertial navigation system (INS) incorporating a ring laser gyro and a 300 kHz Doppler velocity log (DVL). The vehicle also includes acoustic modem, ultra-short baseline navigation, and long-baseline navigation systems. The Mapping AUV is powered by 6 kWhr of Li-polymer batteries, providing expected mission duration of 12 hours at a typical speed of 1.5 m/s. All components of the vehicle are rated to 6000 m depth, allowing MBARI to conduct high-resolution mapping of the deep-ocean seafloor. The sonar package is also be mountable on ROV Ventana, allowing surveys at altitudes less than 20 m at topographically challenging sites. The vehicle was assembled and extensively tested during 2004; this year we are commencing operations for MBARI science projects while continuing the process of testing and integrating the complete suite of sensors and systems. MBARI is beginning to use this capability to observe the changing morphology of dynamic systems such as submarine canyons and active slumps, to map deep-water benthic habitats at resolutions comparable to ROV and submersible observations, to provide basemaps for ROV dives, and to provide high resolution bathymetry and subbottom profiles as part of a variety of projects requiring knowledge of the seafloor. We will present initial results from surveys in and around Monterey Canyon, including high resolution repeat surveys of four sites along the canyon axis.

Hyperspectral surface materials map of quadrangle 3462, Herat (409) and Chishti Sharif (410) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3166, Jaldak (701) and Maruf-Nawa (702) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3670, Jurm-Kishim (223) and Zebak (224) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3164, Lashkar Gah (605) and Kandahar (606) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3562, Khawja-Jir (403) and Murghab (404) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral Surface Materials Map of Quadrangle 3268, Khayr Kot (521) and Urgun (522) Quadrangles, Afghanistan, Showing Iron-bearing Minerals and Other Materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Nuclear Energy Center Site Survey, 1975. Executive summary

International Nuclear Information System (INIS)

1976-01-01

The Nuclear Energy Center Site Survey is a study of a potential alternative siting approach for nuclear power and fuel-cycle facilities, an approach that would cluster sizable groups of such facilities on a relatively small number of sites. The largest aggregation of reactors on a single site being planned today is four, and this quad is assumed (for comparative study purposes) to be the typical dispersed site by the year 2000. Three basic types of nuclear energy centers are considered: power-plant centers, consisting of 10 to 40 nuclear electric generating units of 1200-megawatt electric capacity each; fuel-cycle centers, consisting of fuel reprocessing plants, mixed-oxide fuel fabrication facilities, and radioactive waste management facilities; and combined centers, containing both power plants and fuel-cycle facilities. The results of the general site-location screening efforts are shown on a United States map that shows the locations of large areas identified as likely to contain suitable candidate sites for power NECs, on the basis of four coarse screening criteria: water resources, seismic activity, population density, and statutory excluded lands

BrainMap `95 workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-31

The fourth annual BrainMap workshop was held at La Mansion del Rio Hotel in San Antonio December 3--4, 1995. The conference title was ``Human Brain Mapping and Modeling.`` The meeting was attended by 137 registered participants and 30 observers from 82 institutions representing 12 countries. The meeting focused on the technical issues associated with brain mapping and modeling. A total of 23 papers were presented covering the following topics: spatial normalization and registration; functional image analysis; metanalysis and modeling; and new horizons in biological databases. The full program with abstracts was available on the Research Imaging Center`s web site. A book will be published by John Wiley and Sons prior to the end of 1998.

St. John Benthic Habitat Mapping - Moderate Depth Ground Validation Sites

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Benthic habitats of the moderate-depth marine environment in and around the Virgin Islands Coral Reef National Monument were mapped using a combination of...

Plasticity of orientation preference maps in the visual cortex of adult cats

Science.gov (United States)

Godde, Ben; Leonhardt, Ralph; Cords, Sven M.; Dinse, Hubert R.

2002-01-01

In contrast to the high degree of experience-dependent plasticity usually exhibited by cortical representational maps, a number of experiments performed in visual cortex suggest that the basic layout of orientation preference maps is only barely susceptible to activity-dependent modifications. In fact, most of what we know about activity-dependent plasticity in adults comes from experiments in somatosensory, auditory, or motor cortex. Applying a stimulation protocol that has been proven highly effective in other cortical areas, we demonstrate here that enforced synchronous cortical activity induces major changes of orientation preference maps (OPMs) in adult cats. Combining optical imaging of intrinsic signals and electrophysiological single-cell recordings, we show that a few hours of intracortical microstimulation (ICMS) lead to an enlargement of the cortical representational zone at the ICMS site and an extensive restructuring of the entire OPM layout up to several millimeters away, paralleled by dramatic changes of pinwheel numbers and locations. At the single-cell level, we found that the preferred orientation was shifted toward the orientation of the ICMS site over a region of up to 4 mm. Our results show that manipulating the synchronicity of cortical activity locally without invoking training, attention, or reinforcement, OPMs undergo large-scale reorganization reminiscent of plastic changes observed for nonvisual cortical maps. However, changes were much more widespread and enduring. Such large-scale restructuring of the visual cortical networks indicates a substantial capability for activity-dependent plasticity of adult visual cortex and may provide the basis for cognitive learning processes. PMID:11959906

Recursive definition of global cellular-automata mappings

DEFF Research Database (Denmark)

Feldberg, Rasmus; Knudsen, Carsten; Rasmussen, Steen

1994-01-01

A method for a recursive definition of global cellular-automata mappings is presented. The method is based on a graphical representation of global cellular-automata mappings. For a given cellular-automaton rule the recursive algorithm defines the change of the global cellular-automaton mapping...... as the number of lattice sites is incremented. A proof of lattice size invariance of global cellular-automata mappings is derived from an approximation to the exact recursive definition. The recursive definitions are applied to calculate the fractal dimension of the set of reachable states and of the set...

Genome-Wide Mapping of Collier In Vivo Binding Sites Highlights Its Hierarchical Position in Different Transcription Regulatory Networks.

Directory of Open Access Journals (Sweden)

Mathilde de Taffin

Full Text Available Collier, the single Drosophila COE (Collier/EBF/Olf-1 transcription factor, is required in several developmental processes, including head patterning and specification of muscle and neuron identity during embryogenesis. To identify direct Collier (Col targets in different cell types, we used ChIP-seq to map Col binding sites throughout the genome, at mid-embryogenesis. In vivo Col binding peaks were associated to 415 potential direct target genes. Gene Ontology analysis revealed a strong enrichment in proteins with DNA binding and/or transcription-regulatory properties. Characterization of a selection of candidates, using transgenic CRM-reporter assays, identified direct Col targets in dorso-lateral somatic muscles and specific neuron types in the central nervous system. These data brought new evidence that Col direct control of the expression of the transcription regulators apterous and eyes-absent (eya is critical to specifying neuronal identities. They also showed that cross-regulation between col and eya in muscle progenitor cells is required for specification of muscle identity, revealing a new parallel between the myogenic regulatory networks operating in Drosophila and vertebrates. Col regulation of eya, both in specific muscle and neuronal lineages, may illustrate one mechanism behind the evolutionary diversification of Col biological roles.

Genome-Wide Mapping of Collier In Vivo Binding Sites Highlights Its Hierarchical Position in Different Transcription Regulatory Networks

Science.gov (United States)

Dubois, Laurence; Bataillé, Laetitia; Painset, Anaïs; Le Gras, Stéphanie; Jost, Bernard; Crozatier, Michèle; Vincent, Alain

2015-01-01

Collier, the single Drosophila COE (Collier/EBF/Olf-1) transcription factor, is required in several developmental processes, including head patterning and specification of muscle and neuron identity during embryogenesis. To identify direct Collier (Col) targets in different cell types, we used ChIP-seq to map Col binding sites throughout the genome, at mid-embryogenesis. In vivo Col binding peaks were associated to 415 potential direct target genes. Gene Ontology analysis revealed a strong enrichment in proteins with DNA binding and/or transcription-regulatory properties. Characterization of a selection of candidates, using transgenic CRM-reporter assays, identified direct Col targets in dorso-lateral somatic muscles and specific neuron types in the central nervous system. These data brought new evidence that Col direct control of the expression of the transcription regulators apterous and eyes-absent (eya) is critical to specifying neuronal identities. They also showed that cross-regulation between col and eya in muscle progenitor cells is required for specification of muscle identity, revealing a new parallel between the myogenic regulatory networks operating in Drosophila and vertebrates. Col regulation of eya, both in specific muscle and neuronal lineages, may illustrate one mechanism behind the evolutionary diversification of Col biological roles. PMID:26204530

Three-dimensional glacier surface motion maps at the Gjalp eruption site, Iceland, inferred from combining InSAR and other ice-displacement data

DEFF Research Database (Denmark)

Gudmundsson, S.; Gudmundsson, M. T.; Bjornsson, H.

2002-01-01

be assumed. The 3-D motion maps are created by an optimization process that combines the complementary datasets. The optimization is based on a Markov random-field regularization and a simulated annealing algorithm. The 3-D motion maps show the pattern of gradually diminishing ice flow into the depression...

Semitone frequency mapping to improve music representation for nucleus cochlear implants

Directory of Open Access Journals (Sweden)

Omran Sherif

2011-01-01

Full Text Available Abstract The frequency-to-channel mapping for Cochlear implant (CI signal processors was originally designed to optimize speech perception and generally does not preserve the harmonic structure of music sounds. An algorithm aimed at restoring the harmonic relationship of frequency components based on semitone mapping is presented in this article. Two semitone (Smt based mappings in different frequency ranges were investigated. The first, Smt-LF, covers a range from 130 to 1502 Hz which encompasses the fundamental frequency of most musical instruments. The second, Smt-MF, covers a range from 440 to 5040 Hz, allocating frequency bands of sounds close to their characteristic tonotopical sites according to Greenwood's function. Smt-LF, in contrast, transposes the input frequencies onto locations with higher characteristic frequencies. A sequence of 36 synthetic complex tones (C3 to B5, each consisting of a fundamental and 4 harmonic overtones, was processed using the standard (Std, Smt-LF and Smt-MF mappings. The analysis of output signals showed that the harmonic structure between overtones of all complex tones was preserved using Smt mapping. Semitone mapping preserves the harmonic structure and may in turn improve music representation for Nucleus cochlear implants. The proposed semitone mappings incorporate the use of virtual channels to allow frequencies spanning three and a half octaves to be mapped to 43 stimulation channels. A pitch difference limen test was done with normal hearing subjects discriminating pairs of pure tones with different semitone intervals which were processed by a vocoder type simulator of CI sound processing. The results showed better performance with wider semitone intervals. However, no significant difference was found between 22 and 43 channels maps.

Flood-inundation maps for Grand River, Red Cedar River, and Sycamore Creek near Lansing, Michigan

Science.gov (United States)

Whitehead, Matthew; Ostheimer, Chad J.

2015-08-26

Digital flood-inundation maps for a total of 19.7 miles of the Grand River, the Red Cedar River, and Sycamore Creek were created by the U.S. Geological Survey (USGS) in cooperation with the City of Lansing, Michigan, and the U.S. Army Corps of Engineers. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, show estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at three USGS streamgages: Grand River at Lansing, MI (04113000), Red Cedar River at East Lansing, MI (04112500), and Sycamore Creek at Holt Road near Holt, MI (04112850). Near-real-time stages at these streamgages can be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at all of these sites.

Diversity of MAPs in some plant communities of Stara Planina

Directory of Open Access Journals (Sweden)

Obratov-Petković Dragica

2006-01-01

Full Text Available The high floristic diversity of Stara Planina was the starting base for the research of medicinal and aromatic plants (MAPs in individual forest and meadow communities. The sites Javor and Prelesje, forest community Fagetum moesiacae montanum B. Jov. 1953, pioneer community of birch Betuletum verrucosae s.l. and meadow community Agrostietum vulgaris (capillaris Pavlović, Z. 1955, were researched as follows: soil types, floristic composition and structure of the community, percentage of MAPs, as well as the selection of species which, according to the predetermined criteria can be recommended for further exploitation. The study shows that the soil of the forest communities is eutric brown, and meadow soils are dystric and eutric humus-siliceous. The percentage of MAPs in the floristic structure of the study sites in forest and meadow communities is 32.35%. The following species can be recommended for the collection and utilisation: Hypericum perforatum L., Asperula odorata L., Dryopteris filix-mas (L Schott. Urtica dioica L., Euphorbia amygdaloides L., Prunella grandiflora L. Tanacetum vulgare L., Achillea millefolium L., Rumex acetosa L., Campanula glomerata L., Stachys officinalis (L Trevis., Plantago lanceolata W. et K., Potentilla erecta (L Rauchel, Chamaespartium sagittale (L P. Gibbs. Cynanchum vincetoxicum (L Pers., Euphrasia stricta Host., Fagus moesiaca (Matt Liebl. and Fragaria vesca L.

A 1.4-Billion Pixel Map of the Seafloor: BOEM's Mission to Visualize Dynamic Geology and Identify Natural Seep Sites in the Gulf of Mexico

Science.gov (United States)

Kramer, K.; Shedd, W. W.

2017-12-01

In May, 2017, the U.S. Department of the Interior's Bureau of Ocean Energy Management (BOEM) published a high-resolution seafloor map of the northern Gulf of Mexico region. The new map, derived from 3-D seismic surveys, provides the scientific community with enhanced resolution and reveals previously undiscovered and poorly resolved geologic features of the continental slope, salt minibasin province, abyssal plain, Mississippi Fan, and the Florida Shelf and Escarpment. It becomes an even more powerful scientific tool when paired with BOEM's public database of 35,000 seafloor features, identifying natural hydrocarbon seeps, hard grounds, mud volcanoes, sediment flows, pockmarks, slumps, and many others. BOEM has mapped the Gulf of Mexico seafloor since 1998 in a regulatory mission to identify natural oil and gas seeps and protect the coral and chemosynthetic communities growing at those sites. The nineteen-year mapping effort, still ongoing, resulted in the creation of the 1.4-billion pixel map and the seafloor features database. With these tools and continual collaboration with academia, professional scientific institutions, and the offshore energy industry, BOEM will continue to incorporate new data to update and expand these two resources on a regular basis. They can be downloaded for free from BOEM's website at https://www.boem.gov/Gulf-of-Mexico-Deepwater-Bathymetry/ and https://www.boem.gov/Seismic-Water-Bottom-Anomalies-Map-Gallery/.

Population weighted raster maps can communicate findings of social audits: examples from three continents

Directory of Open Access Journals (Sweden)

Mitchell Steven

2011-12-01

Full Text Available Abstract Background Maps can portray trends, patterns, and spatial differences that might be overlooked in tabular data and are now widely used in health research. Little has been reported about the process of using maps to communicate epidemiological findings. Method Population weighted raster maps show colour changes over the study area. Similar to the rasters of barometric pressure in a weather map, data are the health occurrence – a peak on the map represents a higher value of the indicator in question. The population relevance of each sentinel site, as determined in the stratified last stage random sample, combines with geography (inverse-distance weighting to provide a population-weighted extension of each colour. This transforms the map to show population space rather than simply geographic space. Results Maps allowed discussion of strategies to reduce violence against women in a context of political sensitivity about quoting summary indicator figures. Time-series maps showed planners how experiences of health services had deteriorated despite a reform programme; where in a country HIV risk behaviours were improving; and how knowledge of an economic development programme quickly fell off across a region. Change maps highlighted where indicators were improving and where they were deteriorating. Maps of potential impact of interventions, based on multivariate modelling, displayed how partial and full implementation of programmes could improve outcomes across a country. Scale depends on context. To support local planning, district maps or local government authority maps of health indicators were more useful than national maps; but multinational maps of outcomes were more useful for regional institutions. Mapping was useful to illustrate in which districts enrolment in religious schools – a rare occurrence - was more prevalent. Conclusions Population weighted raster maps can present social audit findings in an accessible and compelling

Population weighted raster maps can communicate findings of social audits: examples from three continents.

Science.gov (United States)

Mitchell, Steven; Cockcroft, Anne; Andersson, Neil

2011-12-21

Maps can portray trends, patterns, and spatial differences that might be overlooked in tabular data and are now widely used in health research. Little has been reported about the process of using maps to communicate epidemiological findings. Population weighted raster maps show colour changes over the study area. Similar to the rasters of barometric pressure in a weather map, data are the health occurrence--a peak on the map represents a higher value of the indicator in question. The population relevance of each sentinel site, as determined in the stratified last stage random sample, combines with geography (inverse-distance weighting) to provide a population-weighted extension of each colour. This transforms the map to show population space rather than simply geographic space. Maps allowed discussion of strategies to reduce violence against women in a context of political sensitivity about quoting summary indicator figures. Time-series maps showed planners how experiences of health services had deteriorated despite a reform programme; where in a country HIV risk behaviours were improving; and how knowledge of an economic development programme quickly fell off across a region. Change maps highlighted where indicators were improving and where they were deteriorating. Maps of potential impact of interventions, based on multivariate modelling, displayed how partial and full implementation of programmes could improve outcomes across a country. Scale depends on context. To support local planning, district maps or local government authority maps of health indicators were more useful than national maps; but multinational maps of outcomes were more useful for regional institutions. Mapping was useful to illustrate in which districts enrolment in religious schools--a rare occurrence--was more prevalent. Population weighted raster maps can present social audit findings in an accessible and compelling way, increasing the use of evidence by planners with limited numeracy

Geologic surface effects of underground nuclear testing, Yucca Flat, Nevada Test Site, Nevada; TOPICAL

International Nuclear Information System (INIS)

Grasso, D.N.

2000-01-01

This report presents a new Geographic Information System composite map of the geologic surface effects caused by underground nuclear testing in the Yucca Flat Physiographic Area of the Nevada Test Site, Nye County, Nevada. The Nevada Test Site (NTS) was established in 1951 as a continental location for testing nuclear devices (Allen and others, 1997, p.3). Originally known as the ''Nevada Proving Ground'', the NTS hosted a total of 928 nuclear detonations, of which 828 were conducted underground (U.S. Department of Energy, 1994). Three principal testing areas of the NTS were used: (1) Yucca Flat, (2) Pahute Mesa, and (3) Rainier Mesa including Aqueduct Mesa. Underground detonations at Yucca Flat and Pahute Mesa were typically emplaced in vertical drill holes, while others were tunnel emplacements. Of the three testing areas, Yucca Flat was the most extensively used, hosting 658 underground tests (747 detonations) located at 719 individual sites (Allen and others, 1997, p.3-4). Figure 1 shows the location of Yucca Flat and other testing areas of the NTS. Figure 2 shows the locations of underground nuclear detonation sites at Yucca Flat. Table 1 lists the number of underground nuclear detonations conducted, the number of borehole sites utilized, and the number of detonations mapped for surface effects at Yucca Flat by NTS Operational Area

Clinical application of sentinel lymph node mapping in colon cancer: in vivo vs. ex vivo techniques.

Science.gov (United States)

Oh, Seung Yeop; Kim, Do Yoon; Kim, Young Bae; Suh, Kwang Wook

2014-09-01

Clinical usefulness of sentinel lymph node (SLN) mapping in colorectal cancer remains controversial. The aim of this study is to evaluate the accuracy of the SLN mapping technique using serial sectioning, and to compare the results between ex vivo and in vivo techniques. From February 2011 to October 2012, 34 colon cancer patients underwent SLN mapping during surgical resection. Eleven patients were analyzed with the in vivo method, and 23 patients with the ex vivo method. Patient characteristics and results of SLN mapping were evaluated. The SLN mapping was performed in 34 patients. Mean age was 67.3 years (range, 44-81 years). Primary tumors were located in the following sites: 13 in the right colon (38.2%) and 21 in the left colon (61.8%). SLN mapping was performed successfully in 88.2% of the patients. There was no significant difference in the identification rate between the two methods (90.9% vs. 87.0%, P = 1.000). Both the mapping methods showed a low sensitivity and high rate of skip metastasis. This study showed that SLN evaluation using serial sectioning could not predict the nodal status with clinically acceptable accuracy despite the high detection rate.

A hydrogeologic map of the Death Valley region, Nevada, and California, developed using GIS techniques

International Nuclear Information System (INIS)

Faunt, C.C.; D'Agnese, F.A.; Turner, A.K.

1997-01-01

In support of Yucca Mountain site characterization studies, a hydrogeologic framework was developed, and a hydrogeologic map was constructed for the Death Valley region. The region, covering approximately 100,000 km 2 along the Nevada-California border near Las Vegas, is characterized by isolated mountain ranges juxtaposed against broad, alluvium-filled valleys. Geologic conditions are typical of the Basin and Range Province; a variety of sedimentary and igneous intrusive and extrusive rocks have been subjected to both compressional and extensional deformation. The regional ground-water flow system can best be described as a series of connected intermontane basins in which ground-water flow occurs in basin-fill deposits, carbonate rocks, clastic rocks, and volcanic rocks. Previous investigations have developed more site-specific hydrogeologic relationships; however, few have described all the lithologies within the Death Valley regional ground-water flow system. Information required to characterize the hydrogeologic units in the region was obtained from regional geologic maps and reports. Map data were digitized from regional geologic maps and combined into a composite map using a geographic information system. This map was simplified to show 10 laterally extensive hydrogeologic units with distinct hydrologic properties. The hydraulic conductivity values for the hydrogeologic units range over 15 orders of magnitude due to the variability in burial depth and degree of fracturing

Wind Atlas for South Africa (WASA) Station and Site Description Report

DEFF Research Database (Denmark)

Mortensen, Niels Gylling; Hansen, Jens Carsten; Kelly, Mark C.

As part of the “Wind Atlas for South Africa” project, site inspection trips were carried out by the Council for Scientific and Industrial Research (CSIR) and Risø DTU in April and June of 2011. A total of 10 sites featuring instrumented 60-m masts were visited; the present report summarises...... the findings of the site inspection teams. The main results are descriptions and documentation of the meteorological masts, instruments and site conditions. For each site, the location and magnetic declination have been determined, as well as the sensor boom directions on the mast. Elevation maps have been...... constructed to show the surrounding terrain and photos taken to document the land cover. Finally, the observed wind roses and wind speed distribution as of 1 October 2013 are shown....

Flood-inundation maps for the White River near Edwardsport, Indiana

Science.gov (United States)

Fowler, Kathleen K.

2014-01-01

Digital flood-inundation maps for a 3.3-mile reach of the White River near Edwardsport, (Ind.), were created by the U.S. Geological Survey (USGS) in cooperation with the Indiana Department of Transportation. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at USGS streamgage 03360730, White River near Edwardsport, Ind. Near-real-time stages at this streamgage may be obtained from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service Advanced Hydrologic Prediction Service at http://water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (site EDWI3.)

Estimated flood-inundation maps for Cowskin Creek in western Wichita, Kansas

Science.gov (United States)

Studley, Seth E.

2003-01-01

The October 31, 1998, flood on Cowskin Creek in western Wichita, Kansas, caused millions of dollars in damages. Emergency management personnel and flood mitigation teams had difficulty in efficiently identifying areas affected by the flooding, and no warning was given to residents because flood-inundation information was not available. To provide detailed information about future flooding on Cowskin Creek, high-resolution estimated flood-inundation maps were developed using geographic information system technology and advanced hydraulic analysis. Two-foot-interval land-surface elevation data from a 1996 flood insurance study were used to create a three-dimensional topographic representation of the study area for hydraulic analysis. The data computed from the hydraulic analyses were converted into geographic information system format with software from the U.S. Army Corps of Engineers' Hydrologic Engineering Center. The results were overlaid on the three-dimensional topographic representation of the study area to produce maps of estimated flood-inundation areas and estimated depths of water in the inundated areas for 1-foot increments on the basis of stream stage at an index streamflow-gaging station. A Web site (http://ks.water.usgs.gov/Kansas/cowskin.floodwatch) was developed to provide the public with information pertaining to flooding in the study area. The Web site shows graphs of the real-time streamflow data for U.S. Geological Survey gaging stations in the area and monitors the National Weather Service Arkansas-Red Basin River Forecast Center for Cowskin Creek flood-forecast information. When a flood is forecast for the Cowskin Creek Basin, an estimated flood-inundation map is displayed for the stream stage closest to the National Weather Service's forecasted peak stage. Users of the Web site are able to view the estimated flood-inundation maps for selected stages at any time and to access information about this report and about flooding in general. Flood

Mapping migratory flyways in Asia using dynamic Brownian bridge movement models.

Science.gov (United States)

Palm, Eric C; Newman, Scott H; Prosser, Diann J; Xiao, Xiangming; Ze, Luo; Batbayar, Nyambayar; Balachandran, Sivananinthaperumal; Takekawa, John Y

2015-01-01

Identifying movement routes and stopover sites is necessary for developing effective management and conservation strategies for migratory animals. In the case of migratory birds, a collection of migration routes, known as a flyway, is often hundreds to thousands of kilometers long and can extend across political boundaries. Flyways encompass the entire geographic range between the breeding and non-breeding areas of a population, species, or a group of species, and they provide spatial frameworks for management and conservation across international borders. Existing flyway maps are largely qualitative accounts based on band returns and survey data rather than observed movement routes. In this study, we use satellite and GPS telemetry data and dynamic Brownian bridge movement models to build upon existing maps and describe waterfowl space use probabilistically in the Central Asian and East Asian-Australasian Flyways. Our approach provided new information on migratory routes that was not easily attainable with existing methods to describe flyways. Utilization distributions from dynamic Brownian bridge movement models identified key staging and stopover sites, migration corridors and general flyway outlines in the Central Asian and East Asian-Australasian Flyways. A map of space use from ruddy shelducks depicted two separate movement corridors within the Central Asian Flyway, likely representing two distinct populations that show relatively strong connectivity between breeding and wintering areas. Bar-headed geese marked at seven locations in the Central Asian Flyway showed heaviest use at several stopover sites in the same general region of high-elevation lakes along the eastern Qinghai-Tibetan Plateau. Our analysis of data from multiple Anatidae species marked at sites throughout Asia highlighted major movement corridors across species and confirmed that the Central Asian and East Asian-Australasian Flyways were spatially distinct. The dynamic Brownian bridge

Recursive definition of global cellular-automata mappings

International Nuclear Information System (INIS)

Feldberg, R.; Knudsen, C.; Rasmussen, S.

1994-01-01

A method for a recursive definition of global cellular-automata mappings is presented. The method is based on a graphical representation of global cellular-automata mappings. For a given cellular-automaton rule the recursive algorithm defines the change of the global cellular-automaton mapping as the number of lattice sites is incremented. A proof of lattice size invariance of global cellular-automata mappings is derived from an approximation to the exact recursive definition. The recursive definitions are applied to calculate the fractal dimension of the set of reachable states and of the set of fixed points of cellular automata on an infinite lattice

Mapping Ecosystem Services’ Values: Current Practice and Future Prospects

OpenAIRE

Jan Philipp Schägner; Luke Brander; Joachim Maes; Volkmar Hartje

2012-01-01

Mapping of ecosystem services' (ESS) values means valuing ESS in monetary terms across a relatively large geographical area and assessing how values vary across space. Thereby, mapping of ESS values reveals additional information as compared to traditional site-specific ESS valuation, which is beneficial for designing land use policies for maintaining ESS supply. Since the well-known article by Costanza et al. (1997), who mapped global ESS values, the number of publications mapping ESS values...

UAV SURVEYING FOR A COMPLETE MAPPING AND DOCUMENTATION OF ARCHAEOLOGICAL FINDINGS. THE EARLY NEOLITHIC SITE OF PORTONOVO

Directory of Open Access Journals (Sweden)

E. S. Malinverni

2016-06-01

Full Text Available The huge potential of 3D digital acquisition techniques for the documentation of archaeological sites, as well as the related findings, is almost well established. In spite of the variety of available techniques, a sole documentation pipeline cannot be defined a priori because of the diversity of archaeological settings. Stratigraphic archaeological excavations, for example, require a systematic, quick and low cost 3D single-surface documentation because the nature of stratigraphic archaeology compels providing documentary evidence of any excavation phase. Only within a destructive process each single excavation cannot be identified, documented and interpreted and this implies the necessity of a re- examination of the work on field. In this context, this paper describes the methodology, carried out during the last years, to 3D document the Early Neolithic site of Portonovo (Ancona, Italy and, in particular, its latest step consisting in a photogrammetric aerial survey by means of UAV platform. It completes the previous research delivered in the same site by means of terrestrial laser scanning and close range techniques and sets out different options for further reflection in terms of site coverage, resolution and campaign cost. With the support of a topographic network and a unique reference system, the full documentation of the site is managed in order to detail each excavation phase; besides, the final output proves how the 3D digital methodology can be completely integrated with reasonable costs during the excavation and used to interpret the archaeological context. Further contribution of this work is the comparison between several acquisition techniques (i.e. terrestrial and aerial, which could be useful as decision support system for different archaeological scenarios. The main objectives of the comparison are: i the evaluation of 3D mapping accuracy from different data sources, ii the definition of a standard pipeline for different

Park Facilities, Boundaries were determined from parcel mapping lines & site specific items, such as shelter locations, were obtained by field GPS observation, Published in 2010, Not Applicable scale, Chippewa County Government.

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — Park Facilities dataset current as of 2010. Boundaries were determined from parcel mapping lines & site specific items, such as shelter locations, were obtained...

Combining geographic information system, multicriteria evaluation techniques and fuzzy logic in siting MSW landfills

Science.gov (United States)

Gemitzi, Alexandra; Tsihrintzis, Vassilios A.; Voudrias, Evangelos; Petalas, Christos; Stravodimos, George

2007-01-01

This study presents a methodology for siting municipal solid waste landfills, coupling geographic information systems (GIS), fuzzy logic, and multicriteria evaluation techniques. Both exclusionary and non-exclusionary criteria are used. Factors, i.e., non-exclusionary criteria, are divided in two distinct groups which do not have the same level of trade off. The first group comprises factors related to the physical environment, which cannot be expressed in terms of monetary cost and, therefore, they do not easily trade off. The second group includes those factors related to human activities, i.e., socioeconomic factors, which can be expressed as financial cost, thus showing a high level of trade off. GIS are used for geographic data acquisition and processing. The analytical hierarchy process (AHP) is the multicriteria evaluation technique used, enhanced with fuzzy factor standardization. Besides assigning weights to factors through the AHP, control over the level of risk and trade off in the siting process is achieved through a second set of weights, i.e., order weights, applied to factors in each factor group, on a pixel-by-pixel basis, thus taking into account the local site characteristics. The method has been applied to Evros prefecture (NE Greece), an area of approximately 4,000 km2. The siting methodology results in two intermediate suitability maps, one related to environmental and the other to socioeconomic criteria. Combination of the two intermediate maps results in the final composite suitability map for landfill siting.

Geological mapping of investigation Trench OL-TK13 at the Olkiluoto study site, Eurajoki, SW Finland

International Nuclear Information System (INIS)

Talikka, M.

2007-04-01

Geological mapping of investigation trench OL-TK13 was carried out by the Geological Survey of Finland at the Olkiluoto study site, Eurajoki, as a part Posiva Oy's site investigation programme for the development of an underground repository for nuclear waste. The east-west striking, ca. 250 m long trench is located in the vicinity of boreholes OL-KR23 and OL-KR27, ca. 250 m east of the ONKALO research facility. The mapping was performed from washed bedrock surface and rock types were determined macroscopically. The main rock types in OL-TK13 are diatexitic gneiss, veined gneiss, pegmatitic granite and K-feldspar porphyry. Mica gneiss and granite/granitized mica gneiss exist to a lesser extent. The diatexitic gneiss is the dominant rock type in the western part and the veined gneiss in the eastern part of the trench. The veined gneiss consists of pelitic mica gneiss paleosome and pegmatitic granite leucosome veins that are parallel to the foliation. In the diatexitic gneiss, the proportion of the leucosome veins and patches is over 50 % and the rock has an ambiguous texture. The pegmatitic granite also occurs as wider sections in the western part of the trench. The K-feldspar porphyry is characterized by potassium feldspar phenocrysts (diameter 4 deformation phase. The migmatitic gneisses were folded during the D 3 deformation phase resulting in small scale, tight and asymmetrical F 3 folds plunging moderately to the NE. During the fracture mapping, all fractures longer than one metre and all fractures intersecting the central thread were investigated. Measurements including orientation, length, fillings, Jr-value, Ja-value and undulation were recorded for a total of 860 fractures. The mean fracture density is 3.5 fracture/m. From the orientation data, three fracture sets were identified: (1) fractures parallel to the foliation, (2) subvertical N-S trending factures and (3) fractures dipping steeply to the N. ∼45 % of all fractures are 0.5-1.5 m in length and �

77 FR 55108 - Explosive Siting Requirements

Science.gov (United States)

2012-09-07

... energy, or a chemical explosion requiring a chemical reaction. Furthermore, an accident may happen... for energetic liquids. \\4\\ Crowl, D.A., Understanding Explosions, AIAA Center for Chemical Process... chemical hazards of energetic liquids used at commercial launch sites. Finally, a site map must now be at a...

Application of raster-based GIS techniques in the siting of landfills in Trabzon Province, Turkey: a case study.

Science.gov (United States)

Yildirim, Volkan

2012-09-01

One of the most important steps in solid waste management is the selection of an appropriate landfill site. The site selection process requires the evaluation and analysis of several criteria. However, the traditional evaluation method is not sufficient for the site selection process. Geographical information system (GIS) technologies are effectively used in the process of site selection, which is a spatial problem. This article describes a raster GIS-based landfill site selection (LSS) method. This method utilizes a raster-based spatial database in which the factors affect the landfill site selection. The final product in this method is the cost surface map showing pixel-based values of the appropriate areas. Furthermore, this GIS-based LSS method was applied for the evaluation of two landfill sites in Trabzon Province in Turkey, for which the traditional evaluation method for site selection was used. The suitability values on the cost surface map of these two landfills have shown that these sites are not appropriate for a solid waste landfill. In conclusion, it was demonstrated that the method of raster GIS-based site selection gives more effective results than traditional methods.

Performing Mimetic Mapping: A Non-Visualisable Map of the Suzhou River Area of Shanghai

Directory of Open Access Journals (Sweden)

Anastasia Karandinou

2014-07-01

Full Text Available This paper questions issues concerning the mapping of experience, through the concept of mimesis – the creative re-performance of the site experience onto the map. The place mapped is the Suzhou River area, a significant part of Shanghai, the former boundary between the British and American Settlements, and an ever-changing and transforming territory. Through the detailed description of the mapping processes, we analyse the position of this particular map within contemporary discourse about mapping. Here, we question the purpose of the process, the desired outcome, the consciousness of the significance of each step/event, and the possible significance of the final traces that the mapping leaves behind. Although after the mapping had been carried out, the procedure was analysed, post-rationalised, and justified through its partial documentation (as part of an educational process, this paper questions the way and the reason for these practices (the post-rationalising of the mapping activity, justifying the strategy, etc., and their possible meaning, purpose, demand or context. Thus we conclude that the subject matter is not the final outcome of an object or ‘map’; there is no final map to be exhibited. What this paper brings forth is the mapping as an event, an action performed by the embodied experience of the actual place and by the trans-local materiality of the tools and elements involved in the process of its making.

78 FR 56749 - Site Characteristics and Site Parameters for Nuclear Power Plants

Science.gov (United States)

2013-09-13

..., ``Geologic Characterization Information,'' (currently titled as ``Basic Geologic and Seismic Information... Ensuring Hazard- Consistent Seismic Input for Site Response and Soil Structure Interaction Analyses,'' NUREG-2115 and NUREG-2117; (2) adding information concerning the Geologic Mapping License Condition; (3...

Hyperspectral surface materials map of quadrangle 3564, Jowand (405) and Gurziwan (406) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

Science.gov (United States)

Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3364, Pasaband (417) and Markaz-e Kajiran (418) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3566, Sangcharak (501) and Sayghan-o-Kamard (502) quadrangles, Afghanistan, showing iron-bearing minerals and other material

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3568, Pul-e Khumri (503) and Charikar (504) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

UO{sub 2}{sup 2+}/protein complexation sites screening

Energy Technology Data Exchange (ETDEWEB)

Guilbaud, P.; Pible, O

2004-07-01

Uranium(VI) is likely to make strong coordination with some proteins in the plasma and in targeted cells. In the frame of a nuclear toxicology program, a biochemical strategy has been developed to identify these targets in complex biological media. The present work focuses on an approach based on the screening of 3D protein structures in order to identify proteins able to bind UO{sub 2}{sup 2+} and the corresponding complexation sites in these proteins. Our preliminary results show that indeed a few proteins display a high affinity to uranyl salt. The site of interaction may be mapped using molecular modeling, providing coherent results with the biochemical data. (authors)

Quantitative multi-parameter mapping of R1, PD*, MT and R2* at 3T: a multi-center validation

Directory of Open Access Journals (Sweden)

Nikolaus eWeiskopf

2013-06-01

Full Text Available Multi-center studies using magnetic resonance imaging facilitate studying small effect sizes, global population variance and rare diseases. The reliability and sensitivity of these multi-center studies crucially depend on the comparability of the data generated at different sites and time points. The level of inter-site comparability is still controversial for conventional anatomical T1-weighted MRI data. Quantitative multi-parameter mapping (MPM was designed to provide MR parameter measures that are comparable across sites and time points, i.e., 1mm high-resolution maps of the longitudinal relaxation rate (R1=1/T1, effective proton density (PD*, magnetization transfer saturation (MT and effective transverse relaxation rate (R2*=1/T2*. MPM was validated at 3T for use in multi-center studies by scanning five volunteers at three different sites. We determined the inter-site bias, inter-site and intra-site coefficient of variation (CoV for typical morphometric measures (i.e., gray matter probability maps used in voxel-based morphometry and the four quantitative parameters. The inter-site bias and CoV were smaller than 3.1% and 8%, respectively, except for the inter-site CoV of R2* (< 20%. The gray matter probability maps based on the MT parameter maps had a 14% higher inter-site reproducibility than maps based on conventional T1-weighted images. The low inter-site bias and variance in the parameters and derived gray matter probability maps confirm the high comparability of the quantitative maps across sites and time points. The reliability, short acquisition time, high resolution and the detailed insights into the brain microstructure provided by MPM makes it an efficient tool for multi-center imaging studies.

Geological Mapping and Identification of Active Fault in Site Candidate of Nuclear Power Plant Installation at Ketapang Area and Its Surroundings, Madura

International Nuclear Information System (INIS)

Ngadenin; Lilik-Subiantoro; Kurnia-Setiawan-W; Agus-Sutriyono; P Widito

2004-01-01

The result of economical study about demand of electric and water supply in Madura Island in 2015 will increase double for domestic or support industry in Madura Island which have to be solved sooner. One way which is considered to solve the problem is Desalination with nuclear electrical plant. In order to support the installation of nuclear Desalination plant, it is needed site free or far from active fault. Active fault is mainly factor to reject the area on site selection process. Aim of the research is to get geological information and identify of active fault in the site candidate of nuclear Desalination plant at Ketapang area and its surrounding by interpretation of air photos and Landsat imagery, geological and structure geological mapping as well as trenching. The lithology of Ketapang and Sokobana site candidate consists of reef and chalky limestone with form of morphology is undulating hills. Structurally, research areas forms a mono cline with east-westerly trending axis, plunging 10 o to E, the direction of strike is W-E, dip 10 o -30 o to the north. This research concludes that an active fault was not found in the area. (author)

Development of a NEHRP site classification map of Chiang Mai city, Thailand, based on shear-wave velocity using the MASW technique

Science.gov (United States)

Thitimakorn, Thanop

2013-08-01

To account for site amplification and seismic hazard mapping, the shear-wave velocity (Vs) profile to a depth of 30 m (Vs (30)) is an important parameter and can be used to calculate the ground motion for specific site conditions. In this study, the near-surface Vs profiles of soils were collected at 44 sites in Chiang Mai city using the multi-channel analysis of surface-wave technique. The Vs of each tested location was average weighted to Vs (30) based on the National Earthquake Hazards Reduction Program (NEHRP) criteria. The average Vs (30) value of the alluvium soils was about 362 m s-1, which falls between NEHRP site classes C and D. The average Vs (30) values of flood plain, fluvial clay and natural levee soils (at 300, 299 and 311 m s-1, respectively) all equated to NEHRP class D. The colluvial deposits in the north-western part of the city were mainly composed of gravel, coarse sand and rock fragments, and were assigned to class C (average Vs (30) of 412 m s-1). Soils with lower Vs values will experience higher earthquake ground shaking than those of the bedrock. Accordingly the major part of Chiang Mai city may experience substantial ground shaking due to the amplification in the soft soils.

Mapping Sites of O-Glycosylation and Fringe Elongation on Drosophila Notch*

Science.gov (United States)

Harvey, Beth M.; Rana, Nadia A.; Moss, Hillary; Leonardi, Jessica; Jafar-Nejad, Hamed; Haltiwanger, Robert S.

2016-01-01

Glycosylation of the Notch receptor is essential for its activity and serves as an important modulator of signaling. Three major forms of O-glycosylation are predicted to occur at consensus sites within the epidermal growth factor-like repeats in the extracellular domain of the receptor: O-fucosylation, O-glucosylation, and O-GlcNAcylation. We have performed comprehensive mass spectral analyses of these three types of O-glycosylation on Drosophila Notch produced in S2 cells and identified peptides containing all 22 predicted O-fucose sites, all 18 predicted O-glucose sites, and all 18 putative O-GlcNAc sites. Using semiquantitative mass spectral methods, we have evaluated the occupancy and relative amounts of glycans at each site. The majority of the O-fucose sites were modified to high stoichiometries. Upon expression of the β3-N-acetylglucosaminyltransferase Fringe with Notch, we observed varying degrees of elongation beyond O-fucose monosaccharide, indicating that Fringe preferentially modifies certain sites more than others. Rumi modified O-glucose sites to high stoichiometries, although elongation of the O-glucose was site-specific. Although the current putative consensus sequence for O-GlcNAcylation predicts 18 O-GlcNAc sites on Notch, we only observed apparent O-GlcNAc modification at five sites. In addition, we performed mass spectral analysis on endogenous Notch purified from Drosophila embryos and found that the glycosylation states were similar to those found on Notch from S2 cells. These data provide foundational information for future studies investigating the mechanisms of how O-glycosylation regulates Notch activity. PMID:27268051

Multi-moment maps

DEFF Research Database (Denmark)

Swann, Andrew Francis; Madsen, Thomas Bruun

2012-01-01

We introduce a notion of moment map adapted to actions of Lie groups that preserve a closed three-form. We show existence of our multi-moment maps in many circumstances, including mild topological assumptions on the underlying manifold. Such maps are also shown to exist for all groups whose second...

Magnetic electroanatomical mapping for ablation of focal atrial tachycardias.

Science.gov (United States)

Marchlinski, F; Callans, D; Gottlieb, C; Rodriguez, E; Coyne, R; Kleinman, D

1998-08-01

Uniform success for ablation of focal atrial tachycardias has been difficult to achieve using standard catheter mapping and ablation techniques. In addition, our understanding of the complex relationship between atrial anatomy, electrophysiology, and surface ECG P wave morphology remains primitive. The magnetic electroanatomical mapping and display system (CARTO) offers an on-line display of electrical activation and/or signal amplitude related to the anatomical location of the recorded sites in the mapped chamber. A window of electrical interest is established based on signals timed from an electrical reference that usually represents a fixed electrogram recording from the coronary sinus or the atrial appendage. This window of electrical interest is established to include atrial activation prior to the onset of the P wave activity associated with the site of origin of a focal atrial tachycardia. Anatomical and electrical landmarks are defined with limited fluoroscopic imaging support and more detailed global chamber and more focal atrial mapping can be performed with minimal fluoroscopic guidance. A three-dimensional color map representing atrial activation or voltage amplitude at the magnetically defined anatomical sites is displayed with on-line data acquisition. This display can be manipulated to facilitate viewing from any angle. Altering the zoom control, triangle fill threshold, clipping plane, or color range can all enhance the display of a more focal area of interest. We documented the feasibility of using this single mapping catheter technique for localizing and ablating focal atrial tachycardias. In a consecutive series of 8 patients with 9 focal atrial tachycardias, the use of the single catheter CARTO mapping system was associated with ablation success in all but one patient who had a left atrial tachycardia localized to the medial aspect of the orifice of the left atrial appendage. Only low power energy delivery was used in this patient because of the

NeuroMap: A spline-based interactive open-source software for spatiotemporal mapping of 2D and 3D MEA data

Directory of Open Access Journals (Sweden)

Oussama eAbdoun

2011-01-01

Full Text Available A major characteristic of neural networks is the complexity of their organization at various spatial scales, from microscopic local circuits to macroscopic brain-scale areas. Understanding how neural information is processed thus entails the ability to study them at multiple scales simultaneously. This is made possible using microelectrodes array (MEA technology. Indeed, high-density MEAs provide large-scale covering (several mm² of whole neural structures combined with microscopic resolution (about 50µm of unit activity. Yet, current options for spatiotemporal representation of MEA-collected data remain limited. Here we present NeuroMap, a new interactive Matlab-based software for spatiotemporal mapping of MEA data. NeuroMap uses thin plate spline interpolation, which provides several assets with respect to conventional mapping methods used currently. First, any MEA design can be considered, including 2D or 3D, regular or irregular, arrangements of electrodes. Second, spline interpolation allows the estimation of activity across the tissue with local extrema not necessarily at recording sites. Finally, this interpolation approach provides a straightforward analytical estimation of the spatial Laplacian for better current sources localization. In this software, coregistration of 2D MEA data on the anatomy of the neural tissue is made possible by fine matching of anatomical data with electrode positions using rigid deformation based correction of anatomical pictures. Overall, NeuroMap provides substantial material for detailed spatiotemporal analysis of MEA data. The package is distributed under GNU General Public License (GPL and available at http://sites.google.com/site/neuromapsoftware.

NeuroMap: A Spline-Based Interactive Open-Source Software for Spatiotemporal Mapping of 2D and 3D MEA Data.

Science.gov (United States)

Abdoun, Oussama; Joucla, Sébastien; Mazzocco, Claire; Yvert, Blaise

2011-01-01

A major characteristic of neural networks is the complexity of their organization at various spatial scales, from microscopic local circuits to macroscopic brain-scale areas. Understanding how neural information is processed thus entails the ability to study them at multiple scales simultaneously. This is made possible using microelectrodes array (MEA) technology. Indeed, high-density MEAs provide large-scale coverage (several square millimeters) of whole neural structures combined with microscopic resolution (about 50 μm) of unit activity. Yet, current options for spatiotemporal representation of MEA-collected data remain limited. Here we present NeuroMap, a new interactive Matlab-based software for spatiotemporal mapping of MEA data. NeuroMap uses thin plate spline interpolation, which provides several assets with respect to conventional mapping methods used currently. First, any MEA design can be considered, including 2D or 3D, regular or irregular, arrangements of electrodes. Second, spline interpolation allows the estimation of activity across the tissue with local extrema not necessarily at recording sites. Finally, this interpolation approach provides a straightforward analytical estimation of the spatial Laplacian for better current sources localization. In this software, coregistration of 2D MEA data on the anatomy of the neural tissue is made possible by fine matching of anatomical data with electrode positions using rigid-deformation-based correction of anatomical pictures. Overall, NeuroMap provides substantial material for detailed spatiotemporal analysis of MEA data. The package is distributed under GNU General Public License and available at http://sites.google.com/site/neuromapsoftware.

Tropospheric Ozonesonde Profiles at Long-term U.S. Monitoring Sites: 1. A Climatology Based on Self-Organizing Maps

Science.gov (United States)

Stauffer, Ryan M.; Thompson, Anne M.; Young, George S.

2016-01-01

Sonde-based climatologies of tropospheric ozone (O3) are vital for developing satellite retrieval algorithms and evaluating chemical transport model output. Typical O3 climatologies average measurements by latitude or region, and season. A recent analysis using self-organizing maps (SOM) to cluster ozonesondes from two tropical sites found that clusters of O3 mixing ratio profiles are an excellent way to capture O3variability and link meteorological influences to O3 profiles. Clusters correspond to distinct meteorological conditions, e.g., convection, subsidence, cloud cover, and transported pollution. Here the SOM technique is extended to four long-term U.S. sites (Boulder, CO; Huntsville, AL; Trinidad Head, CA; and Wallops Island, VA) with4530 total profiles. Sensitivity tests on k-means algorithm and SOM justify use of 3 3 SOM (nine clusters). Ateach site, SOM clusters together O3 profiles with similar tropopause height, 500 hPa height temperature, and amount of tropospheric and total column O3. Cluster means are compared to monthly O3 climatologies.For all four sites, near-tropopause O3 is double (over +100 parts per billion by volume; ppbv) the monthly climatological O3 mixing ratio in three clusters that contain 1316 of profiles, mostly in winter and spring.Large midtropospheric deviations from monthly means (6 ppbv, +710 ppbv O3 at 6 km) are found in two of the most populated clusters (combined 3639 of profiles). These two clusters contain distinctly polluted(summer) and clean O3 (fall-winter, high tropopause) profiles, respectively. As for tropical profiles previously analyzed with SOM, O3 averages are often poor representations of U.S. O3 profile statistics.

Mapping ecosystem services' values : Current practice and future prospects

NARCIS (Netherlands)

Schägner, Jan Philipp; Brander, Luke; Maes, Joachim; Hartje, Volkmar

Mapping of ecosystem services' (ESS) values means valuing ESS in monetary terms across a relatively large geographical area and assessing how values vary across space. Thereby, mapping of ESS values reveals additional information as compared to traditional site-specific ESS valuation, which is

Landscape mapping MAV using single image perspective cues

CSIR Research Space (South Africa)

Tekane, YC

2015-01-01

Full Text Available in order to do mapping, our method does require a 3D model. Instead, our method first classifies the type of site the MAV is in, and the uses vision algorithms based on perspective cues to estimate the landscape location and the do mapping. We tested our...

Remedial Action Plan and site design for stabilization of the inactive uranium mill tailings site at Durango, Colorado: Attachment 2, Geology report

International Nuclear Information System (INIS)

1991-12-01

Detailed investigations of geologic, geomorphic, and seismic conditions at the Bodo Canyon disposal site were conducted. The purpose of these investigations was basic site characterization and identification of potential geologic hazards that could affect long-term site stability. Subsequent engineering studies, such as analyses of hydrologic and liquefaction hazards, used the data developed in these studies. The geomorphic analysis was employed in the design of effective erosion protection. Studies of the regional and local seismotectonic setting, which included a detailed search for possible capable faults within a 65 kilometer radius of the site, provided the basis for seismic design parameters. The scope of work performed included the following: Compilation and analysis of previous published and unpublished geologic literature and maps; Review of historical and instrumental earthquake data; Review of site-specific subsurface geologic data, including lithologic and geophysical logs of exploratory boreholes advanced in the site area; Photogeologic interpretations of existing conventional aerial photographs; and, Ground reconnaissance and mapping of the site region

Application of an adaptive neuro-fuzzy inference system to ground subsidence hazard mapping

Science.gov (United States)

Park, Inhye; Choi, Jaewon; Jin Lee, Moung; Lee, Saro

2012-11-01

We constructed hazard maps of ground subsidence around abandoned underground coal mines (AUCMs) in Samcheok City, Korea, using an adaptive neuro-fuzzy inference system (ANFIS) and a geographical information system (GIS). To evaluate the factors related to ground subsidence, a spatial database was constructed from topographic, geologic, mine tunnel, land use, and ground subsidence maps. An attribute database was also constructed from field investigations and reports on existing ground subsidence areas at the study site. Five major factors causing ground subsidence were extracted: (1) depth of drift; (2) distance from drift; (3) slope gradient; (4) geology; and (5) land use. The adaptive ANFIS model with different types of membership functions (MFs) was then applied for ground subsidence hazard mapping in the study area. Two ground subsidence hazard maps were prepared using the different MFs. Finally, the resulting ground subsidence hazard maps were validated using the ground subsidence test data which were not used for training the ANFIS. The validation results showed 95.12% accuracy using the generalized bell-shaped MF model and 94.94% accuracy using the Sigmoidal2 MF model. These accuracy results show that an ANFIS can be an effective tool in ground subsidence hazard mapping. Analysis of ground subsidence with the ANFIS model suggests that quantitative analysis of ground subsidence near AUCMs is possible.

Mapping the above and belowground biomass in three landscapes in Cameroon, Rwanda and DRC: pilot cases in REDD+ pilot project.

Science.gov (United States)

Sufo Kankeu, R.

2017-12-01

A number of biomass/carbon maps have been recently produced using different approaches and despite their comparison there is still a gap. To fill this gap there is a need to provide accurate maps based on the field data on all types of land use and land cover. Based on the field data from plots established in three pilot projects around Virunga National park in Rwanda, Tri-national Sangha landscape in Cameroon and lac Télé-Lac Tumba landscape in DRC, this paper intend to analyse the relationship between land use change and biomass and present the variability through biomass/carbon maps. The above and belowground biomass was calculated from 95 nested plots of 20 meters radius. The value of biomass/carbon per plot were thus used to elaborate carbon maps of each study site. In the same the way the correlation between the land use and underground and above ground carbon stock were analysed using geographically weighted regression. These data have been joint with classified Spot 5 image and aggregated to come out will acceptable result. Results show that there is a strong relationship between land use in various project sites and the carbon stock related, the change of a forest cover directly impact on carbon stock/biomass.in the same way carbon map realized base on field data and IDW, Kriging or spline module show an idea on the carbon distribution but the maps are not accurate giving the distance between plots,

C-terminal region of MAP7 domain containing protein 3 (MAP7D3 promotes microtubule polymerization by binding at the C-terminal tail of tubulin.

Directory of Open Access Journals (Sweden)

Saroj Yadav

Full Text Available MAP7 domain containing protein 3 (MAP7D3, a newly identified microtubule associated protein, has been shown to promote microtubule assembly and stability. Its microtubule binding region has been reported to consist of two coiled coil motifs located at the N-terminus. It possesses a MAP7 domain near the C-terminus and belongs to the microtubule associated protein 7 (MAP7 family. The MAP7 domain of MAP7 protein has been shown to bind to kinesin-1; however, the role of MAP7 domain in MAP7D3 remains unknown. Based on the bioinformatics analysis of MAP7D3, we hypothesized that the MAP7 domain of MAP7D3 may have microtubule binding activity. Indeed, we found that MAP7 domain of MAP7D3 bound to microtubules as well as enhanced the assembly of microtubules in vitro. Interestingly, a longer fragment MDCT that contained the MAP7 domain (MD with the C-terminal tail (CT of the protein promoted microtubule polymerization to a greater extent than MD and CT individually. MDCT stabilized microtubules against dilution induced disassembly. MDCT bound to reconstituted microtubules with an apparent dissociation constant of 3.0 ± 0.5 µM. An immunostaining experiment showed that MDCT localized along the length of the preassembled microtubules. Competition experiments with tau indicated that MDCT shares its binding site on microtubules with tau. Further, we present evidence indicating that MDCT binds to the C-terminal tail of tubulin. In addition, MDCT could bind to tubulin in HeLa cell extract. Here, we report a microtubule binding region in the C-terminal region of MAP7D3 that may have a role in regulating microtubule assembly dynamics.

Comparing orbiter and rover image-based mapping of an ancient sedimentary environment, Aeolis Palus, Gale crater, Mars

Science.gov (United States)

Stack, Kathryn M.; Edwards, Christopher; Grotzinger, J. P.; Gupta, S.; Sumner, D.; Edgar, Lauren; Fraeman, A.; Jacob, S.; LeDeit, L.; Lewis, K.W.; Rice, M.S.; Rubin, D.; Calef, F.; Edgett, K.; Williams, R.M.E.; Williford, K.H.

2016-01-01

This study provides the first systematic comparison of orbital facies maps with detailed ground-based geology observations from the Mars Science Laboratory (MSL) Curiosity rover to examine the validity of geologic interpretations derived from orbital image data. Orbital facies maps were constructed for the Darwin, Cooperstown, and Kimberley waypoints visited by the Curiosity rover using High Resolution Imaging Science Experiment (HiRISE) images. These maps, which represent the most detailed orbital analysis of these areas to date, were compared with rover image-based geologic maps and stratigraphic columns derived from Curiosity’s Mast Camera (Mastcam) and Mars Hand Lens Imager (MAHLI). Results show that bedrock outcrops can generally be distinguished from unconsolidated surficial deposits in high-resolution orbital images and that orbital facies mapping can be used to recognize geologic contacts between well-exposed bedrock units. However, process-based interpretations derived from orbital image mapping are difficult to infer without known regional context or observable paleogeomorphic indicators, and layer-cake models of stratigraphy derived from orbital maps oversimplify depositional relationships as revealed from a rover perspective. This study also shows that fine-scale orbital image-based mapping of current and future Mars landing sites is essential for optimizing the efficiency and science return of rover surface operations.

Mapping wetlands in Nova Scotia with multi-beam RADARSAT-2 Polarimetric SAR, optical satellite imagery, and Lidar data

Science.gov (United States)

Jahncke, Raymond; Leblon, Brigitte; Bush, Peter; LaRocque, Armand

2018-06-01

Wetland maps currently in use by the Province of Nova Scotia, namely the Department of Natural Resources (DNR) wetland inventory map and the swamp wetland classes of the DNR forest map, need to be updated. In this study, wetlands were mapped in an area southwest of Halifax, Nova Scotia by classifying a combination of multi-date and multi-beam RADARSAT-2 C-band polarimetric SAR (polSAR) images with spring Lidar, and fall QuickBird optical data using the Random Forests (RF) classifier. The resulting map has five wetland classes (open-water/marsh complex, open bog, open fen, shrub/treed fen/bog, swamp), plus lakes and various upland classes. Its accuracy was assessed using data from 156 GPS wetland sites collected in 2012 and compared to the one obtained with the current wetland map of Nova Scotia. The best overall classification was obtained using a combination of Lidar, RADARSAT-2 HH, HV, VH, VV intensity with polarimetric variables, and QuickBird multispectral (89.2%). The classified image was compared to GPS validation sites to assess the mapping accuracy of the wetlands. It was first done considering a group consisting of all wetland classes including lakes. This showed that only 69.9% of the wetland sites were correctly identified when only the QuickBird classified image was used in the classification. With the addition of variables derived from lidar, the number of correctly identified wetlands increased to 88.5%. The accuracy remained the same with the addition of RADARSAT-2 (88.5%). When we tested the accuracy for identifying wetland classes (e.g. marsh complex vs. open bog) instead of grouped wetlands, the resulting wetland map performed best with either QuickBird and Lidar, or QuickBird, Lidar, and RADARSAT-2 (66%). The Province of Nova Scotia's current wetland inventory and its associated wetland classes (aerial-photo interpreted) were also assessed against the GPS wetland sites. This provincial inventory correctly identified 62.2% of the grouped wetlands

Mapping the heparin-binding site of the BMP antagonist gremlin by site-directed mutagenesis based on predictive modelling.

Science.gov (United States)

Tatsinkam, Arnold Junior; Mulloy, Barbara; Rider, Christopher C

2015-08-15

Gremlin is a member of the CAN (cerberus and DAN) family of secreted BMP (bone morphogenetic protein) antagonists and also an agonist of VEGF (vascular endothelial growth factor) receptor-2. It is critical in limb skeleton and kidney development and is re-expressed during tissue fibrosis. Gremlin binds strongly to heparin and heparan sulfate and, in the present study, we sought to investigate its heparin-binding site. In order to explore a putative non-contiguous binding site predicted by computational molecular modelling, we substituted a total of 11 key arginines and lysines located in three basic residue sequence clusters with homologous sequences from cerberus and DAN (differential screening selected gene abberative in neuroblastoma), CAN proteins which lack basic residues in these positions. A panel of six Myc-tagged gremlin mutants, MGR-1-MGR-6 (MGR, mutant gremlin), each containing different combinations of targeted substitutions, all showed markedly reduced affinity for heparin as demonstrated by their NaCl elution on heparin affinity chromatography, thus verifying our predictions. Both MGR-5 and MGR-6 retained BMP-4-binding activity comparable to that of wild-type gremlin. Low-molecular-mass heparin neither promoted nor inhibited BMP-4 binding. Finally, glutaraldehyde cross-linking demonstrated that gremlin forms non-covalent dimers, similar behaviour to that of DAN and also PRDC (protein related to cerberus and DAN), another CAN protein. The resulting dimer would possess two heparin-binding sites, each running along an exposed surface on the second β-strand finger loop of one of the monomers. © 2015 Authors; published by Portland Press Limited.

Final work plan: Expedited Site Characterization of the IES Industries, Inc., Site at Marshalltown, Iowa. Ames Expedited Site Characterization Project, Version 1.0

Energy Technology Data Exchange (ETDEWEB)

1994-04-04

The overall goal of the Ames Laboratory Expedited Site Characterization (ESC) project is to evaluate and promote both innovative and state-of-the-practice site characterization and/or monitoring technologies. This will be accomplished by fielding both types of technologies together in the context of an expedited site characterization. The first site will be at a former manufactured gas plant (FMGP) in Marshalltown, Iowa. The project will field three areas of technology: geophysical, analytical, and data fusion. Geophysical technologies are designed to understand the subsurface geology to help predict fate and transport of the target contaminants. Analytical technologies/methods are designed to detect and quantify the target contaminants. Data fusion technology consists of software systems designed to rapidly integrate or fuse all site information into a conceptual site model that then becomes the decision making tool for the site team to plan subsequent sampling activity. Not all of the contaminants present can be located at the action level. Polynuclear aromatic hydrocarbons (PAHs) are the signature organics associated with the coal tar activities that took place at the site. As a result, PAHs were selected as the target compounds. Screening analytical instruments and nonintrusive geophysical techniques will be fielded to qualitatively map the spatial contaminant distribution. Soil gas surveys, immunoassay testing (IMA), innovative optical techniques, and passive organic sorbent sensors will be deployed along with the geophysical methods. Gas chromatography/mass spectrometry (GC/MS) instruments and a cone penetrometer system equipped with a laser-induced fluorescence (LIF) probe will quantitatively map the action level edges of the PAH plume(s). Samples will be taken both by the cone penetrometer test system (CPT) and the Geoprobe {reg_sign} sampler system.

A software tool for rapid flood inundation mapping

Science.gov (United States)

Verdin, James; Verdin, Kristine; Mathis, Melissa L.; Magadzire, Tamuka; Kabuchanga, Eric; Woodbury, Mark; Gadain, Hussein

2016-06-02

The GIS Flood Tool (GFT) was developed by the U.S. Geological Survey with support from the U.S. Agency for International Development’s Office of U.S. Foreign Disaster Assistance to provide a means for production of reconnaissance-level flood inundation mapping for data-sparse and resource-limited areas of the world. The GFT has also attracted interest as a tool for rapid assessment flood inundation mapping for the Flood Inundation Mapping Program of the U.S. Geological Survey. The GFT can fill an important gap for communities that lack flood inundation mapping by providing a first-estimate of inundation zones, pending availability of resources to complete an engineering study. The tool can also help identify priority areas for application of scarce flood inundation mapping resources. The technical basis of the GFT is an application of the Manning equation for steady flow in an open channel, operating on specially processed digital elevation data. The GFT is implemented as a software extension in ArcGIS. Output maps from the GFT were validated at 11 sites with inundation maps produced previously by the Flood Inundation Mapping Program using standard one-dimensional hydraulic modeling techniques. In 80 percent of the cases, the GFT inundation patterns matched 75 percent or more of the one-dimensional hydraulic model inundation patterns. Lower rates of pattern agreement were seen at sites with low relief and subtle surface water divides. Although the GFT is simple to use, it should be applied with the oversight or review of a qualified hydraulic engineer who understands the simplifying assumptions of the approach.

Climate Prediction Center - Forecasts & Outlook Maps, Graphs and Tables

Science.gov (United States)

Weather Service NWS logo - Click to go to the NWS home page Climate Prediction Center Home Site Map News list below The Climate Prediction Center (CPC) is responsible for issuing seasonal climate outlook maps , and National Centers for Environmental Prediction). These weather and climate products comprise the

SITE: a methodology for assessment of energy facility siting patterns. Regional studies program

International Nuclear Information System (INIS)

Frigerio, N.A.; Habegger, L.J.; King, R.F.; Hoover, L.J.; Clark, N.A.; Cobian, J.M.

1975-08-01

The timely development of the nation's energy production capacity in a manner that minimizes potential adverse local and regional impacts associated with energy facilities requires the use of sophisticated techniques for evaluation of siting alternatives and fuel cycle options. This report is a documentation of the computerized SITE methodology that has been developed for evaluating health, environmental, and socioeconomic impacts related to utilization of alternate sites for energy production within a region of interest. The cost, impact, and attribute vectors, which are generated and displayed on density maps, can be used in a multiparameter overlay process to identify preferable siting areas. The assessment of clustered facilities in energy centers is also possible within the SITE analysis framework. An application of the SITE methodology to Northern Illinois is presented. Also included is a description of the ongoing extension of SITE for the accumulative evaluation of alternative regional energy siting patterns and fuel cycle options. An appendix provides documentation and user information for the SITE computer program

Genome-wide identification and characterisation of human DNA replication origins by initiation site sequencing (ini-seq).

Science.gov (United States)

Langley, Alexander R; Gräf, Stefan; Smith, James C; Krude, Torsten

2016-12-01

Next-generation sequencing has enabled the genome-wide identification of human DNA replication origins. However, different approaches to mapping replication origins, namely (i) sequencing isolated small nascent DNA strands (SNS-seq); (ii) sequencing replication bubbles (bubble-seq) and (iii) sequencing Okazaki fragments (OK-seq), show only limited concordance. To address this controversy, we describe here an independent high-resolution origin mapping technique that we call initiation site sequencing (ini-seq). In this approach, newly replicated DNA is directly labelled with digoxigenin-dUTP near the sites of its initiation in a cell-free system. The labelled DNA is then immunoprecipitated and genomic locations are determined by DNA sequencing. Using this technique we identify >25,000 discrete origin sites at sub-kilobase resolution on the human genome, with high concordance between biological replicates. Most activated origins identified by ini-seq are found at transcriptional start sites and contain G-quadruplex (G4) motifs. They tend to cluster in early-replicating domains, providing a correlation between early replication timing and local density of activated origins. Origins identified by ini-seq show highest concordance with sites identified by SNS-seq, followed by OK-seq and bubble-seq. Furthermore, germline origins identified by positive nucleotide distribution skew jumps overlap with origins identified by ini-seq and OK-seq more frequently and more specifically than do sites identified by either SNS-seq or bubble-seq. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

Site investigation SFR. Boremap mapping of percussion drilled borehole HFR106

Energy Technology Data Exchange (ETDEWEB)

Winell, Sofia (Geosigma AB (Sweden))

2010-06-15

This report presents the result from the Boremap mapping of the percussion drilled borehole HFR106, which is drilled from an islet located ca 220 m southeast of the pier above SFR. The purpose of the location and orientation of the borehole is to investigate the possible occurrence of gently dipping, water-bearing structures in the area. HFR106 has a length of 190.4 m and oriented 269.4 deg/-60.9 deg. The mapping is based on the borehole image (BIPS), investigation of drill cuttings and generalized, as well as more detailed geophysical logs. The dominating rock type, which occupies 68% of HFR106, is fine- to medium-grained, pinkish grey metagranite-granodiorite (rock code 101057) mapped as foliated with a medium to strong intensity. Pegmatite to pegmatitic granite (rock code 101061) occupies 29% of the borehole. Subordinate rock types are felsic to intermediate meta volcanic rock (rock code 103076) and fine- to medium-grained granite (rock code 111058). Rock occurrences (rock types < 1 m in length) occupy about 16% of the mapped interval, of which half is veins, dykes and unspecified occurrences of pegmatite and pegmatitic granite. Only 5.5% of HFR106 is inferred to be altered, mainly oxidation in two intervals with an increased fracture frequency. A total number of 845 fractures are registered in HFR106. Of these are 64 interpreted as open with a certain aperture, 230 open with a possible aperture, and 551 sealed. This result in the following fracture frequencies: 1.6 open fractures/m and 3.0 sealed fractures/m. Three fracture sets of open and sealed fractures with the orientations 290 deg/70 deg, 150 deg/85 deg and 200 deg/85 deg can be distinguished in HFR106. The fracture frequency is generally higher in the second half of the borehole, and particularly in the interval 176-187.4 m.

Site investigation SFR. Boremap mapping of percussion drilled borehole HFR106

International Nuclear Information System (INIS)

Winell, Sofia

2010-06-01

This report presents the result from the Boremap mapping of the percussion drilled borehole HFR106, which is drilled from an islet located ca 220 m southeast of the pier above SFR. The purpose of the location and orientation of the borehole is to investigate the possible occurrence of gently dipping, water-bearing structures in the area. HFR106 has a length of 190.4 m and oriented 269.4 deg/-60.9 deg. The mapping is based on the borehole image (BIPS), investigation of drill cuttings and generalized, as well as more detailed geophysical logs. The dominating rock type, which occupies 68% of HFR106, is fine- to medium-grained, pinkish grey metagranite-granodiorite (rock code 101057) mapped as foliated with a medium to strong intensity. Pegmatite to pegmatitic granite (rock code 101061) occupies 29% of the borehole. Subordinate rock types are felsic to intermediate meta volcanic rock (rock code 103076) and fine- to medium-grained granite (rock code 111058). Rock occurrences (rock types < 1 m in length) occupy about 16% of the mapped interval, of which half is veins, dykes and unspecified occurrences of pegmatite and pegmatitic granite. Only 5.5% of HFR106 is inferred to be altered, mainly oxidation in two intervals with an increased fracture frequency. A total number of 845 fractures are registered in HFR106. Of these are 64 interpreted as open with a certain aperture, 230 open with a possible aperture, and 551 sealed. This result in the following fracture frequencies: 1.6 open fractures/m and 3.0 sealed fractures/m. Three fracture sets of open and sealed fractures with the orientations 290 deg/70 deg, 150 deg/85 deg and 200 deg/85 deg can be distinguished in HFR106. The fracture frequency is generally higher in the second half of the borehole, and particularly in the interval 176-187.4 m

Complex motion of elevators in piecewise map model combined with circle map

Science.gov (United States)

Nagatani, Takashi

2013-11-01

We study the dynamic behavior in the elevator traffic controlled by capacity when the inflow rate of passengers into elevators varies periodically with time. The dynamics of elevators is described by the piecewise map model combined with the circle map. The motion of the elevators depends on the inflow rate, its period, and the number of elevators. The motion in the piecewise map model combined with the circle map shows a complex behavior different from the motion in the piecewise map model.

Digital geologic map in the scale 1:50 000

International Nuclear Information System (INIS)

Kacer, S.; Antalik, M.

2005-01-01

In this presentation authors present preparation of new digital geologic map of the Slovak Republic. This map is prepared by the State Geological Institute of Dionyz Stur as a part of the project Geological information system GeoIS. One of the basic information geologic layers, which will be accessible on the web-site will be digital geologic map of the Slovak Republic in the scale 1: 50 000

Site investigation SFR. Boremap mapping of core drilled borehole KFR106

Energy Technology Data Exchange (ETDEWEB)

Winell, Sofia (Geosigma AB (Sweden))

2010-06-15

This report presents the result from the Boremap mapping of the core drilled borehole KFR106, drilled from an islet ca 220 m southeast of the pier above SFR. The borehole has a length of 300.13 m, and a bearing and inclination of 195.1 deg and -69.9 deg, respectively. The purpose of the location and orientation of the borehole is to investigate the possible occurrence of gently dipping, water-bearing structures in the area. The geological mapping is based on simultaneous study of drill core and borehole image (BIPS). The two lowermost meters of the drill core was mapped in Boremap without access to complementary BIPS-image. The dominating rock type, which occupies 72% of KFR106, is fine- to medium-grained, metagranite granodiorite (rock code 101057), which is foliated with a medium to strong intensity. Pegmatite to pegmatitic granite (rock code 101061) is the second most common rock type and it occupies 16% of the mapped interval. It is also frequent as smaller rock occurrences (< 1 m) in other rock types throughout the borehole. Subordinate rock types are fine- to medium-grained granite (rock code 111058), felsic to intermediate meta volcanic rock (rock code 103076), fine- to medium-grained metagranitoid (rock code 101051) and amphibolite (rock code 102017). Totally 49% of the rock in KFR106 has been mapped as altered, where muscovitization and oxidation is the two most common. Additional shorter intervals of alterations are in decreasing order of abundance quartz dissolution, epidotization, argillization, albitization, chloritization, laumontization and carbonatization. A total number of 2801 fractures are registered in KFR106. Of these are 1059 open, 1742 sealed and 84 partly open. This result in the following fracture frequencies: 6.0 sealed fractures/m, 3.7 open fractures/m and 0.3 partly open fractures/m. In addition there are 5 narrow brecciated zones, and 20 sealed networks with a total length of 18 m. The most frequent fracture fillings in KFR106 are

Precision agriculture - from mapping to site-specific application

DEFF Research Database (Denmark)

Pedersen, Søren Marcus; Lind, Kim Martin Hjorth

2017-01-01

of each chapter in the book. Each chapter address a different topic starting with an overview of technologies that are currently available, followed by specific Variable-Rate Technologies such as VRT fertilizer application, VRT pesticide application, site-specific irrigation management, Auto...

IceMap250—Automatic 250 m Sea Ice Extent Mapping Using MODIS Data

Directory of Open Access Journals (Sweden)

Charles Gignac

2017-01-01

Full Text Available The sea ice cover in the North evolves at a rapid rate. To adequately monitor this evolution, tools with high temporal and spatial resolution are needed. This paper presents IceMap250, an automatic sea ice extent mapping algorithm using MODIS reflective/emissive bands. Hybrid cloud-masking using both the MOD35 mask and a visibility mask, combined with downscaling of Bands 3–7 to 250 m, are utilized to delineate sea ice extent using a decision tree approach. IceMap250 was tested on scenes from the freeze-up, stable cover, and melt seasons in the Hudson Bay complex, in Northeastern Canada. IceMap250 first product is a daily composite sea ice presence map at 250 m. Validation based on comparisons with photo-interpreted ground-truth show the ability of the algorithm to achieve high classification accuracy, with kappa values systematically over 90%. IceMap250 second product is a weekly clear sky map that provides a synthesis of 7 days of daily composite maps. This map, produced using a majority filter, makes the sea ice presence map even more accurate by filtering out the effects of isolated classification errors. The synthesis maps show spatial consistency through time when compared to passive microwave and national ice services maps.

Hyperspectral surface materials map of quadrangle 3264, Naw Zad-Musa Qala (423) and Dihrawud (424) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3570, Tagab-e-Munjan (505) and Asmar-Kamdesh (506) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3468, Chak-e Wardak-Siyahgird (509) and Kabul (510) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Hyperspectral surface materials map of quadrangle 3262, Farah (421) and Hokumat-e-pur-Chaman (422) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Treefall Gap Mapping Using Sentinel-2 Images

Directory of Open Access Journals (Sweden)

Iván Barton

2017-11-01

Full Text Available Proper knowledge about resources in forest management is fundamental. One of the most important parameters of forests is their size or spatial extension. By determining the area of treefall gaps inside the compartments, a more accurate yield can be calculated and the scheduling of forestry operations could be planned better. Several field- and remote sensing-based approaches are in use for mapping but they provide only static measurements at high cost. The Earth Observation satellite mission Sentinel-2 was put in orbit as part of the Copernicus programme. With the 10-m resolution bands, it is possible to observe small-scale forestry operations like treefall gaps. The spatial extension of these gaps is often less than 200 m2, thus their detection can only be done on sub-pixel level. Due to the higher temporal resolution of Sentinel-2, multiple observations are available in a year; therefore, a time series evaluation is possible. The modelling of illumination can increase the accuracy of classification in mountainous areas. The method was tested on three deciduous forest sites in the Börzsöny Mountains in Hungary. The area evaluation produced less than 10% overestimation with the best possible solutions on the sites. The presented work shows a low-cost method for mapping treefall gaps which delivers annual information about the gap area in a deciduous forest.

Landslide susceptibility mapping using a neuro-fuzzy

Science.gov (United States)

Lee, S.; Choi, J.; Oh, H.

2009-12-01

This paper develops and applied an adaptive neuro-fuzzy inference system (ANFIS) based on a geographic information system (GIS) environment using landslide-related factors and location for landslide susceptibility mapping. A neuro-fuzzy system is based on a fuzzy system that is trained by a learning algorithm derived from the neural network theory. The learning procedure operates on local information, and causes only local modifications in the underlying fuzzy system. The study area, Boun, suffered much damage following heavy rain in 1998 and was selected as a suitable site for the evaluation of the frequency and distribution of landslides. Boun is located in the central part of Korea. Landslide-related factors such as slope, soil texture, wood type, lithology, and density of lineament were extracted from topographic, soil, forest, and lineament maps. Landslide locations were identified from interpretation of aerial photographs and field surveys. Landslide-susceptible areas were analyzed by the ANFIS method and mapped using occurrence factors. In particular, we applied various membership functions (MFs) and analysis results were verified using the landslide location data. The predictive maps using triangular, trapezoidal, and polynomial MFs were the best individual MFs for modeling landslide susceptibility maps (84.96% accuracy), proving that ANFIS could be very effective in modeling landslide susceptibility mapping. Various MFs were used in this study, and after verification, the difference in accuracy according to the MFs was small, between 84.81% and 84.96%. The difference was just 0.15% and therefore the choice of MFs was not important in the study. Also, compared with the likelihood ratio model, which showed 84.94%, the accuracy was similar. Thus, the ANFIS could be applied to other study areas with different data and other study methods such as cross-validation. The developed ANFIS learns the if-then rules between landslide-related factors and landslide

UMineAR: Mobile-Tablet-Based Abandoned Mine Hazard Site Investigation Support System Using Augmented Reality

Directory of Open Access Journals (Sweden)

Jangwon Suh

2017-10-01

Full Text Available Conventional mine site investigation has difficulties in fostering location awareness and understanding the subsurface environment; moreover, it produces a large amount of hardcopy data. To overcome these limitations, the UMineAR mobile tablet application was developed. It enables users to rapidly identify underground mine objects (drifts, entrances, boreholes, hazards and intuitively visualize them in 3D using a mobile augmented reality (AR technique. To design UMineAR, South Korean georeferenced standard-mine geographic information system (GIS databases were employed. A web database system was designed to access via a tablet groundwater-level data measured every hour by sensors installed in boreholes. UMineAR consists of search, AR, map, and database modules. The search module provides data retrieval and visualization options/functions. The AR module provides 3D interactive visualization of mine GIS data and camera imagery on the tablet screen. The map module shows the locations of corresponding borehole data on a 2D map. The database module provides mine GIS database management functions. A case study showed that the proposed application is suitable for onsite visualization of high-volume mine GIS data based on geolocations; no specialized equipment or skills are required to understand the underground mine environment. UMineAR can be used to support abandoned-mine hazard site investigations.

Elevation data for floodplain mapping

National Research Council Canada - National Science Library

Committee on Floodplain Mapping Technologies; National Research Council; Division on Earth and Life Studies; National Research Council

2007-01-01

.... Elevation Data for Floodplain Mapping shows that there is sufficient two-dimensional base map imagery to meet FEMA's flood map modernization goals, but that the three-dimensional base elevation data...

A GIS- Based suitability analysis for siting a solid waste in an urban area

Directory of Open Access Journals (Sweden)

M. Salemi

2017-01-01

Full Text Available An appropriate solid waste disposal has been a major problem in municipal environment. The use of landfills is the most economical and environmentally acceptable method for the disposal of solid waste all over the world. The analysis of spatial data and consideration of regulation and accepted criteria are part of the important elements in the site selection. The aim of this paper is to show how application of geographic information system could be used for siting solid waste disposal in Abadan city. In this paper, we consider types of soil suitable for solid waste disposals, land use/ land cover, transportation routes and proximity to surface water. Relative importance weight of each criteria in the geographic information system was determined and finally suitability map was prepared. Based on the final suitability map, appropriate solid waste landfill site was located in north east part of the study area. Select the best landfill site among the candidate ones, and   the output results can enable decision makers to make appropriate decisions to reduce the costs both in   economic and environmental criteria.

Conceptual maps as evaluation strategy

Directory of Open Access Journals (Sweden)

Dionísio Borsato

2007-03-01

Full Text Available The following work shows the conceptual map as an evaluation tool. In this study, an opening text was used as a previous organizer, with a theme related to the students’ daily lives. The developed activity consisted in elaborating conceptual maps before and after the experimental works. The evaluation was applied to 21 students of the 1st grade and 22 of the 3rd grade of High School. The elaborated maps were scored according to hierarchy, propositions, linking words, cross linking and examples. The classification of the maps elaborated before and after the experimental activity, was obtained having as a parameter, a referential conceptual map. In this classification many differences were observed between the first and second maps of both grades and among the groups. The elaboration of conceptual maps showed great potential as evaluation resources.

Surface mineral maps of Afghanistan derived from HyMap imaging spectrometer data, version 2

Science.gov (United States)

Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.

2013-01-01

This report presents a new version of surface mineral maps derived from HyMap imaging spectrometer data collected over Afghanistan in the fall of 2007. This report also describes the processing steps applied to the imaging spectrometer data. The 218 individual flight lines composing the Afghanistan dataset, covering more than 438,000 square kilometers, were georeferenced to a mosaic of orthorectified Landsat images. The HyMap data were converted from radiance to reflectance using a radiative transfer program in combination with ground-calibration sites and a network of cross-cutting calibration flight lines. The U.S. Geological Survey Material Identification and Characterization Algorithm (MICA) was used to generate two thematic maps of surface minerals: a map of iron-bearing minerals and other materials, which have their primary absorption features at the shorter wavelengths of the reflected solar wavelength range, and a map of carbonates, phyllosilicates, sulfates, altered minerals, and other materials, which have their primary absorption features at the longer wavelengths of the reflected solar wavelength range. In contrast to the original version, version 2 of these maps is provided at full resolution of 23-meter pixel size. The thematic maps, MICA summary images, and the material fit and depth images are distributed in digital files linked to this report, in a format readable by remote sensing software and Geographic Information Systems (GIS). The digital files can be downloaded from http://pubs.usgs.gov/ds/787/downloads/.

Mapping of sand deposition from 1993 midwest floods with electromagnetic induction measurements

International Nuclear Information System (INIS)

Kitchen, N.R.; Sudduth, K.A.; Drummond, S.T.

1996-01-01

Sand deposition on river-bottom farmland was extensive from the 1993 Midwest floods. A technique coupling electromagnetic induction (EM) ground conductivity sensing and Global Positioning System (GPS) location data was used to map sand deposition depth at four sites in Missouri along the Missouri River. A strong relationship between EM reading and probe measured depth of sand deposition (r 2 values between 0.73-0.94) was found. This relationship differed significantly between sites, so calibration by ground-truthing was required for each sand deposition survey. An example of the sand deposition mapping using the EM/GPS system is shown for two 50-60 ha (125-150 ac) sites. Such maps can provide valuable detailed information for developing restoration plans for land affected by 1993 Midwest floods. (author)

A rapid stability assessment of China's IGS sites after the Ms7. 0 Lushan earthquake

Directory of Open Access Journals (Sweden)

Meng Jie

2013-05-01

Full Text Available A rapid and accurate assessment of the stability of surveying and mapping reference points is important for post – disaster rescue, disaster relief and reconstruction activities. Using Precise Point Positioning (PPP technology, a rapid assessment of the stability of the IGS sites in China was performed after the Ms 7. 0 Lushan earthquake using rapid precise ephemeris and rapid precise satellite clock products. The results show that the earthquake had a very small impact and did not cause significant permanent deformation at the IGS sites. Most of the sites were unaffected and remained stable after the earthquake.

Fracture mapping at the Spent Fuel Test-Climax

International Nuclear Information System (INIS)

Wilder, D.G.; Yow, J.L. Jr.

1981-05-01

Mapping of geologic discontinuities has been done in several phases at the Spent Fuel Test-Climax (SFT-C) in the granitic Climax stock at the Nevada Test Site. Mapping was carried out in the tail drift, access drift, canister drift, heater drifts, instrumentation alcove, and receiving room. The fractures mapped as intersecting a horizontal datum in the canister and heater drifts are shown on one figure. Fracture sketch maps have been compiled as additional figures. Geologic mapping efforts were scheduled around and significantly impacted by the excavation and construction schedules. Several people were involved in the mapping, and over 2500 geologic discontinuities were mapped, including joints, shears, and faults. Some variance between individuals' mapping efforts was noticed, and the effects of various magnetic influences upon a compass were examined. The examination of compass errors improved the credibility of the data. The compass analysis work is explained in Appendix A. Analysis of the fracture data will be presented in a future report

Michigan Magnetic and Gravity Maps and Data: A Website for the Distribution of Data

Science.gov (United States)

Daniels, David L.; Kucks, Robert P.; Hill, Patricia L.; Snyder, Stephen L.

2009-01-01

This web site provides the best available, public-domain, aeromagnetic and gravity data in the State of Michigan and merges these data into composite grids that are available for downloading. The magnetic grid is compiled from 25 separate magnetic surveys that have been knit together to form a single composite digital grid and map. The magnetic survey grids have been continued to 305 meters (1,000 feet) above ground and merged together to form the State compilation. A separate map shows the location of the aeromagnetic surveys, color-coded to the survey flight-line spacing. In addition, a complete Bouguer gravity anomaly grid and map were generated from more than 20,000 gravity station measurements from 33 surveys. A table provides the facts about each gravity survey where known.

Genome-wide mapping of boundary element-associated factor (BEAF) binding sites in Drosophila melanogaster links BEAF to transcription.

Science.gov (United States)

Jiang, Nan; Emberly, Eldon; Cuvier, Olivier; Hart, Craig M

2009-07-01

Insulator elements play a role in gene regulation that is potentially linked to nuclear organization. Boundary element-associated factors (BEAFs) 32A and 32B associate with hundreds of sites on Drosophila polytene chromosomes. We hybridized DNA isolated by chromatin immunoprecipitation to genome tiling microarrays to construct a genome-wide map of BEAF binding locations. A distinct difference in the association of 32A and 32B with chromatin was noted. We identified 1,820 BEAF peaks and found that more than 85% were less than 300 bp from transcription start sites. Half are between head-to-head gene pairs. BEAF-associated genes are transcriptionally active as judged by the presence of RNA polymerase II, dimethylated histone H3 K4, and the alternative histone H3.3. Forty percent of these genes are also associated with the polymerase negative elongation factor NELF. Like NELF-associated genes, most BEAF-associated genes are highly expressed. Using quantitative reverse transcription-PCR, we found that the expression levels of most BEAF-associated genes decrease in embryos and cultured cells lacking BEAF. These results provide an unexpected link between BEAF and transcription, suggesting that BEAF plays a role in maintaining most associated promoter regions in an environment that facilitates high transcription levels.

Right parietal cortex and calculation processing: intraoperative functional mapping of multiplication and addition in patients affected by a brain tumor.

Science.gov (United States)

Della Puppa, Alessandro; De Pellegrin, Serena; d'Avella, Elena; Gioffrè, Giorgio; Munari, Marina; Saladini, Marina; Salillas, Elena; Scienza, Renato; Semenza, Carlo

2013-11-01

The role of parietal areas in number processing is well known. The significance of intraoperative functional mapping of these areas has been only partially explored, however, and only a few discordant data are available in the surgical literature with regard to the right parietal lobe. The purpose of this study was to evaluate the clinical impact of simple calculation in cortical electrostimulation of right-handed patients affected by a right parietal brain tumor. Calculation mapping in awake surgery was performed in 3 right-handed patients affected by high-grade gliomas located in the right parietal lobe. Preoperatively, none of the patients presented with calculation deficits. In all 3 cases, after sensorimotor and language mapping, cortical and intraparietal sulcus areas involved in single-digit multiplication and addition calculations were mapped using bipolar electrostimulation. In all patients, different sites of the right parietal cortex, mainly in the inferior lobule, were detected as being specifically related to calculation (multiplication or addition). In 2 patients the intraparietal sulcus was functionally specific for multiplication. No functional sites for language were detected. All sites functional for calculation were spared during tumor resection, which was complete in all cases without postoperative neurological deficits. These findings provide intraoperative data in support of an anatomofunctional organization for multiplication and addition within the right parietal area. Furthermore, the study shows the potential clinical relevance of intraoperative mapping of calculation in patients undergoing surgery in the right parietal area. Further and larger studies are needed to confirm these data and assess whether mapped areas are effectively essential for function.

Inferring the most probable maps of underground utilities using Bayesian mapping model

Science.gov (United States)

Bilal, Muhammad; Khan, Wasiq; Muggleton, Jennifer; Rustighi, Emiliano; Jenks, Hugo; Pennock, Steve R.; Atkins, Phil R.; Cohn, Anthony

2018-03-01

Mapping the Underworld (MTU), a major initiative in the UK, is focused on addressing social, environmental and economic consequences raised from the inability to locate buried underground utilities (such as pipes and cables) by developing a multi-sensor mobile device. The aim of MTU device is to locate different types of buried assets in real time with the use of automated data processing techniques and statutory records. The statutory records, even though typically being inaccurate and incomplete, provide useful prior information on what is buried under the ground and where. However, the integration of information from multiple sensors (raw data) with these qualitative maps and their visualization is challenging and requires the implementation of robust machine learning/data fusion approaches. An approach for automated creation of revised maps was developed as a Bayesian Mapping model in this paper by integrating the knowledge extracted from sensors raw data and available statutory records. The combination of statutory records with the hypotheses from sensors was for initial estimation of what might be found underground and roughly where. The maps were (re)constructed using automated image segmentation techniques for hypotheses extraction and Bayesian classification techniques for segment-manhole connections. The model consisting of image segmentation algorithm and various Bayesian classification techniques (segment recognition and expectation maximization (EM) algorithm) provided robust performance on various simulated as well as real sites in terms of predicting linear/non-linear segments and constructing refined 2D/3D maps.

Advances in characterizing ubiquitylation sites by mass spectrometry

DEFF Research Database (Denmark)

Sylvestersen, K.B.; Young, C.; Nielsen, M.L.

2013-01-01

of ubiquitylation is a two-fold challenge that involves the mapping of ubiquitylation sites and the determination of ubiquitin chain topology. This review focuses on the technical advances in the mass spectrometry-based characterization of ubiquitylation sites, which have recently involved the large...

Engineering study of generic site criteria for selected DOE plutonium facilities

International Nuclear Information System (INIS)

Kingsbury, R.J.; Greenwood, J.M.; Sandoval, M.D.

1980-09-01

The objectives of this study were to identify criteria that would be applied to selection of a site for plutonium facilities such as those at the Rocky Flats Plant, to establish the relative importance of these criteria, and to identify suitable areas within the United States for location of plutonium facilities with respect to these criteria. Sources of the site criteria identified include federal laws, federal agency regulations, state laws and regulations, and requirements associated with operations to be performed at the site. The criteria identified during the study were organized into 14 major categories. The relative importnace of each category and each criterion within the categories were established using group decision-making techniques. The major criteria categories, their assigned weight on a scale of 1 to 10, and their relative priority ranks are as follows: geology/seismicity; public safety; environmental impact; meteorology; hydrology; topography; transportation; utilities; personnel; safeguards/security; land area and availability; land use compatibility; and, public acceptance. A suitability analysis of the continental United States was performed using only those criteria that could be mapped at a national scale. Suitability was assessed with respect to each of these criteria, and individual suitability maps were prepared. A composite suitability map was generated using computerized overlay techniques. This map provides a starting point for identifying specific candidate sites if an actual site selection were to be conducted

Using knowledge rules for pharmacy mapping.

Science.gov (United States)

Shakib, Shaun C; Che, Chengjian; Lau, Lee Min

2006-01-01

The 3M Health Information Systems (HIS) Healthcare Data Dictionary (HDD) is used to encode and structure patient medication data for the Electronic Health Record (EHR) of the Department of Defense's (DoD's) Armed Forces Health Longitudinal Technology Application (AHLTA). HDD Subject Matter Experts (SMEs) are responsible for initial and maintenance mapping of disparate, standalone medication master files from all 100 DoD host sites worldwide to a single concept-based vocabulary, to accomplish semantic interoperability. To achieve higher levels of automation, SMEs began defining a growing set of knowledge rules. These knowledge rules were implemented in a pharmacy mapping tool, which enhanced consistency through automation and increased mapping rate by 29%.

BrainMap '95 workshop. Final report

International Nuclear Information System (INIS)

1995-01-01

The fourth annual BrainMap workshop was held at La Mansion del Rio Hotel in San Antonio December 3--4, 1995. The conference title was ''Human Brain Mapping and Modeling.'' The meeting was attended by 137 registered participants and 30 observers from 82 institutions representing 12 countries. The meeting focused on the technical issues associated with brain mapping and modeling. A total of 23 papers were presented covering the following topics: spatial normalization and registration; functional image analysis; metanalysis and modeling; and new horizons in biological databases. The full program with abstracts was available on the Research Imaging Center's web site. A book will be published by John Wiley and Sons prior to the end of 1998

Permafrost distribution map of San Juan Dry Andes (Argentina) based on rock glacier sites

Science.gov (United States)

Esper Angillieri, María Yanina

2017-01-01

Rock glaciers are frozen water reservoirs in mountainous areas. Water resources are important for the local populations and economies. The presence of rock glaciers is commonly used as a direct indicator of mountain permafrost conditions. Over 500 active rock glaciers have been identified, showing that elevations between 3500 and 4500 m asl., a south-facing or east-facing aspect, areas with relatively low solar radiation and low mean annual air temperature (-4 to 0 °C) favour the existence of rock glaciers in this region. The permafrost probability model, for Dry Andes of San Juan Province between latitudes 28º30‧S and 32°30‧S, have been analyzed by logistic regression models based on the active rock glaciers occurrence in relation to some topoclimatic variables such as altitude, aspect, mean annual temperature, mean annual precipitation and solar radiation, using optical remote sensing techniques in a GIS environment. The predictive performances of the model have been estimated by known rock glaciers locations and by the area under the receiver operating characteristic curve (AUROC). This regional permafrost map can be applied by the Argentinean Government for their recent initiatives which include creating inventories, monitoring and studying ice masses along the Argentinean Andes. Further, this generated map provides valuable input data for permafrost scenarios and contributes to a better understanding of our geosystem.

Texture mapping via optimal mass transport.

Science.gov (United States)

Dominitz, Ayelet; Tannenbaum, Allen

2010-01-01

In this paper, we present a novel method for texture mapping of closed surfaces. Our method is based on the technique of optimal mass transport (also known as the "earth-mover's metric"). This is a classical problem that concerns determining the optimal way, in the sense of minimal transportation cost, of moving a pile of soil from one site to another. In our context, the resulting mapping is area preserving and minimizes angle distortion in the optimal mass sense. Indeed, we first begin with an angle-preserving mapping (which may greatly distort area) and then correct it using the mass transport procedure derived via a certain gradient flow. In order to obtain fast convergence to the optimal mapping, we incorporate a multiresolution scheme into our flow. We also use ideas from discrete exterior calculus in our computations.

Application of time domain induced polarization to the mapping of lithotypes in a landfill site

DEFF Research Database (Denmark)

Legaz, Aurélie; Fiandaca, Gianluca; Pedersen, Jesper Bjergsted

2012-01-01

area. It is known that both waste deposits andclay have clear signatures in TDIP data, making it possibleto enhance the resolution of geological structures comparedto DC surveys alone.Four DC/TDIP profiles were carried out crossing the landfill,and another seven profiles in the surroundings providea.......Results show that it is possible to resolve both the geometryof the buried waste body and key geological structures.In particular, it was possible to find a silt/clay lens at depththat correlates with the flow direction of the pollution plumespreading out from the landfill and to map a shallow sandylayer rich...

Remedial Action Plan and site design for stabilization of the inactive uranium mill tailings site at Durango, Colorado: Attachment 2, Geology report. Revised final report

Energy Technology Data Exchange (ETDEWEB)

1991-12-01

Detailed investigations of geologic, geomorphic, and seismic conditions at the Bodo Canyon disposal site were conducted. The purpose of these investigations was basic site characterization and identification of potential geologic hazards that could affect long-term site stability. Subsequent engineering studies, such as analyses of hydrologic and liquefaction hazards, used the data developed in these studies. The geomorphic analysis was employed in the design of effective erosion protection. Studies of the regional and local seismotectonic setting, which included a detailed search for possible capable faults within a 65 kilometer radius of the site, provided the basis for seismic design parameters. The scope of work performed included the following: Compilation and analysis of previous published and unpublished geologic literature and maps; Review of historical and instrumental earthquake data; Review of site-specific subsurface geologic data, including lithologic and geophysical logs of exploratory boreholes advanced in the site area; Photogeologic interpretations of existing conventional aerial photographs; and, Ground reconnaissance and mapping of the site region.

A geomorphic approach to 100-year floodplain mapping for the Conterminous United States

Science.gov (United States)

Jafarzadegan, Keighobad; Merwade, Venkatesh; Saksena, Siddharth

2018-06-01

Floodplain mapping using hydrodynamic models is difficult in data scarce regions. Additionally, using hydrodynamic models to map floodplain over large stream network can be computationally challenging. Some of these limitations of floodplain mapping using hydrodynamic modeling can be overcome by developing computationally efficient statistical methods to identify floodplains in large and ungauged watersheds using publicly available data. This paper proposes a geomorphic model to generate probabilistic 100-year floodplain maps for the Conterminous United States (CONUS). The proposed model first categorizes the watersheds in the CONUS into three classes based on the height of the water surface corresponding to the 100-year flood from the streambed. Next, the probability that any watershed in the CONUS belongs to one of these three classes is computed through supervised classification using watershed characteristics related to topography, hydrography, land use and climate. The result of this classification is then fed into a probabilistic threshold binary classifier (PTBC) to generate the probabilistic 100-year floodplain maps. The supervised classification algorithm is trained by using the 100-year Flood Insurance Rated Maps (FIRM) from the U.S. Federal Emergency Management Agency (FEMA). FEMA FIRMs are also used to validate the performance of the proposed model in areas not included in the training. Additionally, HEC-RAS model generated flood inundation extents are used to validate the model performance at fifteen sites that lack FEMA maps. Validation results show that the probabilistic 100-year floodplain maps, generated by proposed model, match well with both FEMA and HEC-RAS generated maps. On average, the error of predicted flood extents is around 14% across the CONUS. The high accuracy of the validation results shows the reliability of the geomorphic model as an alternative approach for fast and cost effective delineation of 100-year floodplains for the CONUS.

Topography and geology site effects from the intensity prediction model (ShakeMap) for Austria

Science.gov (United States)

del Puy Papí Isaba, María; Jia, Yan; Weginger, Stefan

2017-04-01

The seismicity in Austria can be categorized as moderated. Despite the fact that the hazard seems to be rather low, earthquakes can cause great damage and losses, specially in densely populated and industrialized areas. It is well known, that equations which predict intensity as a function of magnitude and distance, among other parameters, are useful tool for hazard and risk assessment. Therefore, this study aims to determine an empirical model of the ground shaking intensities (ShakeMap) of a series of earthquakes occurred in Austria between 1000 and 2014. Furthermore, the obtained empirical model will lead to further interpretation of both, contemporary and historical earthquakes. A total of 285 events, which epicenters were located in Austria, and a sum of 22.739 reported macreoseismic data points from Austria and adjoining countries, were used. These events are enclosed in the period 1000-2014 and characterized by having a local magnitude greater than 3. In the first state of the model development, the data was careful selected, e.g. solely intensities equal or greater than III were used. In a second state the data was adjusted to the selected empirical model. Finally, geology and topography corrections were obtained by means of the model residuals in order to derive intensity-based site amplification effects.

Site scale wetness classification of tundra regions with C-band SAR satellite data

DEFF Research Database (Denmark)

Widhalm, Barbara; Bartsch, Annett; Siewert, Matthias Benjamin

2016-01-01

of this approach at site scale using ENVISAT ASAR WS data (∼120 m resolution). These higher resolution ASAR WS maps have been produced for study sites representing different settings throughout the Arctic and compared to high resolution land cover maps and field survey data. It can be shown that a medium...

Minimalism through intraoperative functional mapping.

Science.gov (United States)

Berger, M S

1996-01-01

Intraoperative stimulation mapping may be used to avoid unnecessary risk to functional regions subserving language and sensori-motor pathways. Based on the data presented here, language localization is variable in the entire population, with only certainty existing for the inferior frontal region responsible for motor speech. Anatomical landmarks such as the anterior temporal tip for temporal lobe language sites and the posterior aspect of the lateral sphenoid wing for the frontal lobe language zones are unreliable in avoiding postoperative aphasias. Thus, individual mapping to identify essential language sites has the greatest likelihood of avoiding permanent deficits in naming, reading, and motor speech. In a similar approach, motor and sensory pathways from the cortex and underlying white matter may be reliably stimulated and mapped in both awake and asleep patients. Although these techniques require an additional operative time and equipment nominally priced, the result is often gratifying, as postoperative morbidity has been greatly reduced in the process of incorporating these surgical strategies. The patients quality of life is improved in terms of seizure control, with or without antiepileptic drugs. This avoids having to perform a second costly operative procedure, which is routinely done when extraoperative stimulation and recording is done via subdural grids. In addition, an aggressive tumor resection at the initial operation lengthens the time to tumor recurrence and often obviates the need for a subsequent reoperation. Thus, intraoperative functional mapping may be best alluded to as a surgical technique that results in "minimalism in the long term".

Using low-cost drones to map malaria vector habitats.

Science.gov (United States)

Hardy, Andy; Makame, Makame; Cross, Dónall; Majambere, Silas; Msellem, Mwinyi

2017-01-14

There is a growing awareness that if we are to achieve the ambitious goal of malaria elimination, we must compliment indoor-based vector control interventions (such as bednets and indoor spraying) with outdoor-based interventions such as larval source management (LSM). The effectiveness of LSM is limited by our capacity to identify and map mosquito aquatic habitats. This study provides a proof of concept for the use of a low-cost (drone (DJI Phantom) for mapping water bodies in seven sites across Zanzibar including natural water bodies, irrigated and non-irrigated rice paddies, peri-urban and urban locations. With flying times of less than 30 min for each site, high-resolution (7 cm) georeferenced images were successfully generated for each of the seven sites, covering areas up to 30 ha. Water bodies were readily identifiable in the imagery, as well as ancillary information for planning LSM activities (access routes to water bodies by road and foot) and public health management (e.g. identification of drinking water sources, mapping individual households and the nature of their construction). The drone-based surveys carried out in this study provide a low-cost and flexible solution to mapping water bodies for operational dissemination of LSM initiatives in mosquito vector-borne disease elimination campaigns. Generated orthomosaics can also be used to provide vital information for other public health planning activities.

Flood-inundation maps for White River at Petersburg, Indiana

Science.gov (United States)

Fowler, Kathleen K.

2015-08-20

Digital flood-inundation maps for a 7.7-mile reach of the White River at Petersburg, Indiana, were created by the U.S. Geological Survey (USGS), in cooperation with the Indiana Office of Community and Rural Affairs. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage at White River at Petersburg, Ind. (03374000). Near-real-time stages at this streamgage may be obtained from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service (NWS) Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at this site (PTRI3).

Nuclear Energy Center Site Survey, 1975. Part V. Resource availability and site screening

International Nuclear Information System (INIS)

1976-01-01

Resource requirements for nuclear energy centers are discussed and the large land areas which meet these requirements and may contain potential sites for a nuclear energy center (NEC) are identified. Maps of the areas are included that identify seismic zones, river flow rates, and population density

Comparing Kriging and Regression Approaches for Mapping Soil Clay Content in a diverse Danish Landscape

DEFF Research Database (Denmark)

Adhikari, Kabindra; Bou Kheir, Rania; Greve, Mette Balslev

2013-01-01

Information on the spatial variability of soil texture including soil clay content in a landscape is very important for agricultural and environmental use. Different prediction techniques are available to assess and map spatial variability of soil properties, but selecting the most suitable techn...... the prediction in OKst compared with that in OK, whereas RT showed the lowest performance of all (R2 = 0.52; RMSE = 0.52; and RPD = 1.17). We found RKrr to be an effective prediction method and recommend this method for any future soil mapping activities in Denmark....... technique at a given site has always been a major issue in all soil mapping applications. We studied the prediction performance of ordinary kriging (OK), stratified OK (OKst), regression trees (RT), and rule-based regression kriging (RKrr) for digital mapping of soil clay content at 30.4-m grid size using 6...

Mapping the geographical distribution of lymphatic filariasis in Zambia

DEFF Research Database (Denmark)

Mwase, Enala T; Stensgaard, Anna-Sofie; Nsakashalo-Senkwe, Mutale

2014-01-01

to be an important determinant of medium-high prevalence levels. CONCLUSIONS/SIGNIFICANCE: LF was found to be surprisingly widespread in Zambia, although in most places with low prevalence. The produced maps and the identified environmental correlates of LF infection will provide useful guidance for planning...... volunteers from 108 geo-referenced survey sites across Zambia were examined for circulating filarial antigens (CFA) with rapid format ICT cards, and a map indicating the distribution of CFA prevalences in Zambia was prepared. 78% of survey sites had CFA positive cases, with prevalences ranging between 1......% and 54%. Most positive survey sites had low prevalence, but six foci with more than 15% prevalence were identified. The observed geographical variation in prevalence pattern was examined in more detail using a species distribution modeling approach to explore environmental requirements for parasite...

Contextualising Archaeological Information Through Interactive Maps

Directory of Open Access Journals (Sweden)

Ian Johnson

2002-09-01

Full Text Available Many web sites use maps delivered as non-interactive images. With the development of web-enabled mapping, new methods of presenting and contextualising archaeological and historical data are becoming available. However, most current examples are static views of contemporary framework data or specific time slices, and do not provide interactivity relating to the time dimension, which is so important to archaeology and related disciplines. In this article I look at some of the advantages of time-enabled interactive mapping and map animation in providing educational experiences to museum visitors and the web-browsing public. These will be illustrated through three example applications of the TimeMap methodology developed at the University of Sydney Archaeological Computing Laboratory: 1. the Sydney TimeMap kiosk at the Museum of Sydney; 2. an embedded Java mapping applet developed for MacquarieNet, a major Australian online educational encyclopaedia; and 3. the metadata clearinghouse mapping applet developed for the Electronic Cultural Atlas Initiative, Berkeley. In each of these examples, a wide range of resources are delivered through a time-enabled map interface which accesses live database data rather than pre-structured curated presentations of data. This flexibility brings its own challenges in providing intuitive pathways and appropriate levels of detail in response to free-ranging user enquiries. The paper outlines some of the approaches I have adopted to resolve these issues.

LiDAR Mapping of Earthquake Uplifted Paleo-shorelines, Southern Wairarapa Coast, North Island, New Zealand

Science.gov (United States)

Valenciano, J.; Angenent, J.; Marshall, J. S.; Clark, K.; Litchfield, N. J.

2017-12-01

The Hikurangi subduction margin along the east coast of the North Island, New Zealand accommodates oblique convergence of the Pacific Plate westward beneath the Australian plate at 45 mm/yr. Pronounced forearc uplift occurs at the southern end of the margin along the Wairarapa coast, onshore of the subducting Hikurangi plateau. Along a narrow coastal lowland, a series of uplifted Holocene marine terraces and beach ridges preserve a geologic record of prehistoric coseismic uplift events. In January 2017, we participated in the Research Experience for Undergraduates (REU) program of the NSF SHIRE Project (Subduction at Hikurangi Integrated Research Experiment). We visited multiple coastal sites for reconnaissance fieldwork to select locations for future in-depth study. For the coastline between Flat Point and Te Kaukau Point, we used airborne LiDAR data provided by Land Information New Zealand (LINZ) to create ArcGIS digital terrain models for mapping and correlating uplifted paleo-shorelines. Terrace elevations derived from the LiDAR data were calibrated through the use of Real Time Kinematic (RTK) GPS surveying at one field site (Glenburn Station). Prior field mapping and radiocarbon dating results (Berryman et al., 2001; Litchfield and Clark, 2015) were used to guide our LiDAR mapping efforts. The resultant maps show between four and seven uplifted terraces and associated beach ridges along this coastal segment. At some sites, terrace mapping and lateral correlation are impeded by discontinuous exposures and the presence of landslide debris, alluvial fan deposits, and sand dunes. Tectonic uplift along the southern Hikurangi margin is generated by a complex interaction between deep megathrust slip and shallow upper-plate faulting. Each uplifted Holocene paleo-shoreline is interpreted to represent a single coseismic uplift event. Continued mapping, surveying, and age dating may help differentiate between very large margin-wide megathrust earthquakes (M8.0-9.0+) and

Geographic Information System Tools for Management of US DOE Sites - 13489

International Nuclear Information System (INIS)

Carpenter, Cliff; Pilz, Elaine; Pawel, Steve

2013-01-01

The DOE Office of Legacy Management (LM) uses a variety of GIS tools to support long-term surveillance and maintenance (LTS and M) activities at DOE closure sites. These geo-spatial applications provide access to data both for external public viewing and for internal analysis and decision making. LM uses a custom geo-spatial application called geo-spatial Environmental Mapping System (GEMS) that draws validated information from a database of 4.6 million analytical results and 232,000 water level measurements for 58 LTS and M sites. These data were collected from transferred sites over a period of 40 years. The database is used to capture and store historical environmental information such as analytical chemistry data, groundwater depths and elevations, well logs, well construction data, geo-referenced boundaries, site physical features, and sampling locations from LTS and M sites. Stakeholders, regulators, and project personnel can use this Web-based application and data to display information in several forms, such as a tabular report, a graph, and a geo-spatial display, or the data can be labeled or highlighted in a map view. Institutional controls, with their LTS and M requirements and documentation, have recently been incorporated into a prototype GEMS Web page for the Weldon Spring, Missouri, Site. LM uses multiple internal GIS viewers to help ensure the future protection of human health and the environment. For example, at the Rocky Flats, Colorado, Site, LM uses a GIS application to display real property interests on authoritative maps. Another project is used to facilitate discussions at stakeholder meetings for the Rocky Flats site's Original Landfill. The Uranium Leasing Program uses multiple interactive maps that assist in ongoing monitoring and the oversight of lease-holders' activities. (authors)

Geographic Information System Tools for Management of US DOE Sites - 13489

Energy Technology Data Exchange (ETDEWEB)

Carpenter, Cliff [U.S. Department of Energy Office of Legacy Management, 99 Research Park Road, Morgantown, WV 26505 (United States); Pilz, Elaine [S.M. Stoller Corporation, 2597 Legacy Way, Grand Junction, CO 81503 (United States); Pawel, Steve [S.M. Stoller Corporation, 10995 Hamilton-Cleves Highway, Harrison, OH 45030 (United States)

2013-07-01

The DOE Office of Legacy Management (LM) uses a variety of GIS tools to support long-term surveillance and maintenance (LTS and M) activities at DOE closure sites. These geo-spatial applications provide access to data both for external public viewing and for internal analysis and decision making. LM uses a custom geo-spatial application called geo-spatial Environmental Mapping System (GEMS) that draws validated information from a database of 4.6 million analytical results and 232,000 water level measurements for 58 LTS and M sites. These data were collected from transferred sites over a period of 40 years. The database is used to capture and store historical environmental information such as analytical chemistry data, groundwater depths and elevations, well logs, well construction data, geo-referenced boundaries, site physical features, and sampling locations from LTS and M sites. Stakeholders, regulators, and project personnel can use this Web-based application and data to display information in several forms, such as a tabular report, a graph, and a geo-spatial display, or the data can be labeled or highlighted in a map view. Institutional controls, with their LTS and M requirements and documentation, have recently been incorporated into a prototype GEMS Web page for the Weldon Spring, Missouri, Site. LM uses multiple internal GIS viewers to help ensure the future protection of human health and the environment. For example, at the Rocky Flats, Colorado, Site, LM uses a GIS application to display real property interests on authoritative maps. Another project is used to facilitate discussions at stakeholder meetings for the Rocky Flats site's Original Landfill. The Uranium Leasing Program uses multiple interactive maps that assist in ongoing monitoring and the oversight of lease-holders' activities. (authors)

PhosphOrtholog: a web-based tool for cross-species mapping of orthologous protein post-translational modifications.

Science.gov (United States)

Chaudhuri, Rima; Sadrieh, Arash; Hoffman, Nolan J; Parker, Benjamin L; Humphrey, Sean J; Stöckli, Jacqueline; Hill, Adam P; James, David E; Yang, Jean Yee Hwa

2015-08-19

Most biological processes are influenced by protein post-translational modifications (PTMs). Identifying novel PTM sites in different organisms, including humans and model organisms, has expedited our understanding of key signal transduction mechanisms. However, with increasing availability of deep, quantitative datasets in diverse species, there is a growing need for tools to facilitate cross-species comparison of PTM data. This is particularly important because functionally important modification sites are more likely to be evolutionarily conserved; yet cross-species comparison of PTMs is difficult since they often lie in structurally disordered protein domains. Current tools that address this can only map known PTMs between species based on known orthologous phosphosites, and do not enable the cross-species mapping of newly identified modification sites. Here, we addressed this by developing a web-based software tool, PhosphOrtholog ( www.phosphortholog.com ) that accurately maps protein modification sites between different species. This facilitates the comparison of datasets derived from multiple species, and should be a valuable tool for the proteomics community. Here we describe PhosphOrtholog, a web-based application for mapping known and novel orthologous PTM sites from experimental data obtained from different species. PhosphOrtholog is the only generic and automated tool that enables cross-species comparison of large-scale PTM datasets without relying on existing PTM databases. This is achieved through pairwise sequence alignment of orthologous protein residues. To demonstrate its utility we apply it to two sets of human and rat muscle phosphoproteomes generated following insulin and exercise stimulation, respectively, and one publicly available mouse phosphoproteome following cellular stress revealing high mapping and coverage efficiency. Although coverage statistics are dataset dependent, PhosphOrtholog increased the number of cross-species mapped sites

Geophysical investigation, Salmon Site, Lamar County, Mississippi

International Nuclear Information System (INIS)

1995-02-01

Geophysical surveys were conducted in 1992 and 1993 on 21 sites at the Salmon Site (SS) located in Lamar County, Mississippi. The studies are part of the Remedial Investigation/Feasibility Study (RI/FS) being conducted by IT Corporation for the U.S. Department of Energy (DOE). During the 1960s, two nuclear devices and two chemical tests were detonated 826 meters (in) (2710 feet [ft]) below the ground surface in the salt dome underlying the SS. These tests were part of the Vela Uniform Program conducted to improve the United States capability to detect, identify, and locate underground nuclear detonations. The RI/FS is being conducted to determine if any contamination is migrating from the underground shot cavity in the salt dome and if there is any residual contamination in the near surface mud and debris disposal pits used during the testing activities. The objective of the surface geophysical surveys was to locate buried debris, disposal pits, and abandoned mud pits that may be present at the site. This information will then be used to identify the locations for test pits, cone penetrometer tests, and drill hole/monitor well installation. The disposal pits were used during the operation of the test site in the 1960s. Vertical magnetic gradient (magnetic gradient), electromagnetic (EM) conductivity, and ground-penetrating radar (GPR) surveys were used to accomplish these objectives. A description of the equipment used and a theoretical discussion of the geophysical methods are presented Appendix A. Because of the large number of figures relative to the number of pages of text, the geophysical grid-location maps, the contour maps of the magnetic-gradient data, the contour maps of the EM conductivity data, and the GPR traverse location maps are located in Appendix B, Tabs I through 22. In addition, selected GPR records are located in Appendix C

Mapping Palaeohydrography in Deserts: Contribution from Space-Borne Imaging Radar

Directory of Open Access Journals (Sweden)

Philippe Paillou

2017-03-01

Full Text Available Space-borne Synthetic Aperture Radar (SAR has the capability to image subsurface features down to several meters in arid regions. A first demonstration of this capability was performed in the Egyptian desert during the early eighties, thanks to the first Shuttle Imaging Radar mission. Global coverage provided by recent SARs, such as the Japanese ALOS/PALSAR sensor, allowed the mapping of vast ancient hydrographic systems in Northern Africa. We present a summary of palaeohydrography results obtained using PALSAR data over large deserts such as the Sahara and the Gobi. An ancient river system was discovered in eastern Lybia, connecting in the past the Kufrah oasis to the Mediterranean Sea, and the terminal part of the Tamanrasett river was mapped in western Mauritania, ending with a large submarine canyon. In southern Mongolia, PALSAR images combined with topography analysis allowed the mapping of the ancient Ulaan Nuur lake. We finally show the potentials of future low frequency SAR sensors by comparing L-band (1.25 GHz and P-band (435 MHz airborne SAR acquisitions over a desert site in southern Tunisia.

Hyperspectral surface materials map of quadrangle 3466, La`l wa Sar Jangal (507) and Bamyan (508) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

MX Siting Investigation. MX System Siting Summary Report. Land Acquisition Application Package Map Sheets. Volume III.

Science.gov (United States)

1982-01-18

Environmental Impact Statement DMA Defense Mapping Agency DOPAA Description of Proposed Actions and Alternatives DTA Designated Training Area DTN Designated...Transportation Network EIS Environmental Impact Statement FLPMA Federal Land Policy Management Act FNI Fugro National, Inc. FSED Full Scale Engineering...CONTRACT OR GRANT NUMBER(s) 9. PERFORMING ORGANIZATION NAME AND ADDRESS 10. PROGRAM ELEMENT. PROJECT. TASK Cr+e wec - r Tniz. Q6 cr-% e rL!: Pktcxim Nat*’v

High-resolution YAC-cosmid-STS map of human chromosome 13.

Science.gov (United States)

Cayanis, E; Russo, J J; Kalachikov, S; Ye, X; Park, S H; Sunjevaric, I; Bonaldo, M F; Lawton, L; Venkatraj, V S; Schon, E; Soares, M B; Rothstein, R; Warburton, D; Edelman, I S; Zhang, P; Efstratiadis, A; Fischer, S G

1998-01-01

We have assembled a high-resolution physical map of human chromosome 13 DNA (approximately 114 Mb) from hybridization, PCR, and FISH mapping data using a specifically designed set of computer programs. Although the mapping of 13p is limited, 13q (approximately 98 Mb) is covered by an almost continuous contig of 736 YACs aligned to 597 contigs of cosmids. Of a total of 10,789 cosmids initially selected from a chromosome 13-specific cosmid library (16,896 colonies) using inter-Alu PCR probes from the YACs and probes for markers mapped to chromosome 13, 511 were assembled in contigs that were established from cross-hybridization relationships between the cosmids. The 13q YAC-cosmid map was annotated with 655 sequence tagged sites (STSs) with an average spacing of 1 STS per 150 kb. This set of STSs, each identified by a D number and cytogenetic location, includes database markers (198), expressed sequence tags (93), and STSs generated by sequencing of the ends of cosmid inserts (364). Additional annotation has been provided by positioning 197 cosmids mapped by FISH on 13q. The final (comprehensive) map, a list of STS primers, and raw data used in map assembly are available at our Web site (genome1.ccc.columbia.edu/ approximately genome/) and can serve as a resource to facilitate accurate localization of additional markers, provide substrates for sequencing, and assist in the discovery of chromosome 13 genes associated with hereditary diseases.

Seabed maps showing topography, ruggedness, backscatter intensity, sediment mobility, and the distribution of geologic substrates in Quadrangle 6 of the Stellwagen Bank National Marine Sanctuary Region offshore of Boston, Massachusetts

Science.gov (United States)

Valentine, Page C.; Gallea, Leslie B.

2015-11-10

The U.S. Geological Survey (USGS), in cooperation with the National Oceanic and Atmospheric Administration's National Marine Sanctuary Program, has conducted seabed mapping and related research in the Stellwagen Bank National Marine Sanctuary (SBNMS) region since 1993. The area is approximately 3,700 square kilometers (km2) and is subdivided into 18 quadrangles. Seven maps, at a scale of 1:25,000, of quadrangle 6 (211 km2) depict seabed topography, backscatter, ruggedness, geology, substrate mobility, mud content, and areas dominated by fine-grained or coarse-grained sand. Interpretations of bathymetric and seabed backscatter imagery, photographs, video, and grain-size analyses were used to create the geology-based maps. In all, data from 420 stations were analyzed, including sediment samples from 325 locations. The seabed geology map shows the distribution of 10 substrate types ranging from boulder ridges to immobile, muddy sand to mobile, rippled sand. Mapped substrate types are defined on the basis of sediment grain-size composition, surface morphology, sediment layering, the mobility or immobility of substrate surfaces, and water depth range. This map series is intended to portray the major geological elements (substrates, topographic features, processes) of environments within quadrangle 6. Additionally, these maps will be the basis for the study of the ecological requirements of invertebrate and vertebrate species that utilize these substrates and guide seabed management in the region.

Mapping of p140Cap phosphorylation sites

DEFF Research Database (Denmark)

Repetto, Daniele; Aramu, Simona; Boeri Erba, Elisabetta

2013-01-01

phosphorylation and tunes its interactions with other regulatory molecules via post-translation modification. In this work, using mass spectrometry, we found that p140Cap is in vivo phosphorylated on tyrosine (Y) within the peptide GEGLpYADPYGLLHEGR (from now on referred to as EGLYA) as well as on three serine...... residues. Consistently, EGLYA has the highest score of in silico prediction of p140Cap phosphorylation. To further investigate the p140Cap function, we performed site specific mutagenesis on tyrosines inserted in EGLYA and EPLYA, a second sequence with the same highest score of phosphorylation. The mutant...

The status of soil mapping for the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Olson, G.L.; Lee, R.D.; Jeppesen, D.J.

1995-01-01

This report discusses the production of a revised version of the general soil map of the 2304-km 2 (890-mi 2 ) Idaho National Engineering Laboratory (INEL) site in southeastern Idaho and the production of a geographic information system (GIS) soil map and supporting database. The revised general soil map replaces an INEL soil map produced in 1978 and incorporates the most current information on INEL soils. The general soil map delineates large soil associations based on National Resources Conservation Services [formerly the Soil Conservation Service (SCS)] principles of soil mapping. The GIS map incorporates detailed information that could not be presented on the general soil map and is linked to a database that contains the soil map unit descriptions, surficial geology codes, and other pertinent information

Topographical mapping system for hazardous and radiological environments

International Nuclear Information System (INIS)

Armstrong, G.A.; Burks, B.L.; Bernacki, B.E.; Pardini, A.

1995-01-01

This report focuses on the results of the acceptance test of the Topographical Mapping System (TMS) delivered to the Hanford site. The TMS was tested for accuracy over the specified range of 45 feet. The TMS was also tested to ensure that the unit could be deployed through multiple risers and maintain accuracy and registration of the surface mapping data. In addition, the TMS was disassembled and reassembled and redeployed to test field replacement of modules that make up the sensor head that is deployed in the vapor space of Underground Storage Tanks such as those located at the Hanford site in southeastern Washington State. The results from these tests along with temperature testing on the complete system and radiation testing of selected susceptible components are covered in this report. The primary purpose of the TMS is to generate reliable and accurate three-dimensional maps of the internal surfaces of storage tank. One use for these mapping systems is in creating and maintaining a current map of the tank interior as input to a robotic ''world model'' that is used to test remediation strategies or plan robot trajectories. Another use is tracking the movement of the waste surface as it responds to expanding bubbles of trapped Gas. A third use of the TMS is to perform a volumetric analysis of the amount of waste removed from the tanks during remediation

Lithological-morphological map of Italy: Instrument for environmental protection

International Nuclear Information System (INIS)

Noe', L.

1991-01-01

This paper describes the development by ENEA (Italian Commission for New Technologies, Energy and the Environment) of a map which identifies and coordinates the principal lithological and morphological features of Italy's environmental ecosystems. The map is intended especially for use in site characterization studies and environmental impacts assessments in construction projects involving hydroelectric power dams and geothermal power plants

Bioavailability of particulate metal to zebra mussels: Biodynamic modelling shows that assimilation efficiencies are site-specific

Energy Technology Data Exchange (ETDEWEB)

Bourgeault, Adeline, E-mail: bourgeault@ensil.unilim.fr [Cemagref, Unite de Recherche Hydrosystemes et Bioprocedes, 1 rue Pierre-Gilles de Gennes, 92761 Antony (France); FIRE, FR-3020, 4 place Jussieu, 75005 Paris (France); Gourlay-France, Catherine, E-mail: catherine.gourlay@cemagref.fr [Cemagref, Unite de Recherche Hydrosystemes et Bioprocedes, 1 rue Pierre-Gilles de Gennes, 92761 Antony (France); FIRE, FR-3020, 4 place Jussieu, 75005 Paris (France); Priadi, Cindy, E-mail: cindy.priadi@eng.ui.ac.id [LSCE/IPSL CEA-CNRS-UVSQ, Avenue de la Terrasse, 91198 Gif-sur-Yvette (France); Ayrault, Sophie, E-mail: Sophie.Ayrault@lsce.ipsl.fr [LSCE/IPSL CEA-CNRS-UVSQ, Avenue de la Terrasse, 91198 Gif-sur-Yvette (France); Tusseau-Vuillemin, Marie-Helene, E-mail: Marie-helene.tusseau@ifremer.fr [IFREMER Technopolis 40, 155 rue Jean-Jacques Rousseau, 92138 Issy-Les-Moulineaux (France)

2011-12-15

This study investigates the ability of the biodynamic model to predict the trophic bioaccumulation of cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni) and zinc (Zn) in a freshwater bivalve. Zebra mussels were transplanted to three sites along the Seine River (France) and collected monthly for 11 months. Measurements of the metal body burdens in mussels were compared with the predictions from the biodynamic model. The exchangeable fraction of metal particles did not account for the bioavailability of particulate metals, since it did not capture the differences between sites. The assimilation efficiency (AE) parameter is necessary to take into account biotic factors influencing particulate metal bioavailability. The biodynamic model, applied with AEs from the literature, overestimated the measured concentrations in zebra mussels, the extent of overestimation being site-specific. Therefore, an original methodology was proposed for in situ AE measurements for each site and metal. - Highlights: > Exchangeable fraction of metal particles did not account for the bioavailability of particulate metals. > Need for site-specific biodynamic parameters. > Field-determined AE provide a good fit between the biodynamic model predictions and bioaccumulation measurements. - The interpretation of metal bioaccumulation in transplanted zebra mussels with biodynamic modelling highlights the need for site-specific assimilation efficiencies of particulate metals.

Map showing principal drainage basins, principal runoff-producing areas, and selected stream flow data in the Kaiparowits coal-basin area, Utah

Science.gov (United States)

Price, Don

1978-01-01

This is one of a series of maps that describe the geology and related natural resources in the Kaiparowits coal-basin area. Streamflow records used to compile this map and the accompanying table were collected by the U.S. Geological Survey in cooperation with the Utah State Engineer and the Utah Department of Transportation. The principal runoff-producing areas were delineated from a work map (scale 1:250,000) compiled to estimate water yields in Utah (Bagley and others, 1964). Information about Lake Powell was furnished by the U.S. Bureau of Reclamation.

Maps of the Martian Landing Sites and Rover Traverses: Viking 1 and 2, Mars Pathfinder, and Phoenix Landers, and the Mars Exploration Rovers.

Science.gov (United States)

Parker, T. J.; Calef, F. J., III; Deen, R. G.; Gengl, H.

2016-12-01

The traverse maps produced tactically for the MER and MSL rover missions are the first step in placing the observations made by each vehicle into a local and regional geologic context. For the MER, Phoenix and MSL missions, 25cm/pixel HiRISE data is available for accurately localizing the vehicles. Viking and Mars Pathfinder, however, relied on Viking Orbiter images of several tens of m/pixel to triangulate to horizon features visible both from the ground and from orbit. After Pathfinder, MGS MOC images became available for these landing sites, enabling much better correlations to horizon features and localization predictions to be made, that were then corroborated with HiRISE images beginning 9 years ago. By combining topography data from MGS, Mars Express, and stereo processing of MRO CTX and HiRISE images into orthomosaics (ORRs) and digital elevation models (DEMs), it is possible to localize all the landers and rover positions to an accuracy of a few tens of meters with respect to the Mars global control net, and to better than half a meter with respect to other features within a HiRISE orthomosaic. JPL's MIPL produces point clouds of the MER Navcam stereo images that can be processed into 1cm/pixel ORR/DEMs that are then georeferenced to a HiRISE/CTX base map and DEM. This allows compilation of seamless mosaics of the lander and rover camera-based ORR/DEMs with the HiRISE ORR/DEM that can be viewed in 3 dimensions with GIS programs with that capability. We are re-processing the Viking Lander, Mars Pathfinder, and Phoenix lander data to allow similar ORR/DEM products to be made for those missions. For the fixed landers and Spirit, we will compile merged surface/CTX/HiRISE ORR/DEMs, that will enable accurate local and regional mapping of these landing sites, and allow comparisons of the results from these missions to be made with current and future surface missions.

Introducing a method for mapping recreational experience

DEFF Research Database (Denmark)

Lindholst, Andrej Christian; Dempsey, Nicola; Burton, Mel

2013-01-01

spaces provide and support a range of recreational experiences. The exploration reported here is based on a short review of the methods background and an application in two test sites in Sheffield, South Yorkshire in early summer 2010. This paper critically appraises the application of rec......-mapping’, an innovative method of analysing and mapping positive recreational experiences in urban green spaces is explored and piloted within the UK planning context. Originating in the Nordic countries, this on-site method can provide urban planners and designers with data about the extent to which specific green......-mapping at smaller spatial scales and recommends further explorations within the UK planning context, as the method adds to existing open space assessment by providing a unique layer of information to analyse more fully the recreational qualities of urban green spaces....

Hybrid geomorphological maps as the basis for assessing geoconservation potential in Lech, Vorarlberg (Austria)

Science.gov (United States)

Seijmonsbergen, Harry; de Jong, Mat; Anders, Niels; de Graaff, Leo; Cammeraat, Erik

2013-04-01

Geoconservation potential is, in our approach, closely linked to the spatial distribution of geomorphological sites and thus, geomorphological inventories. Detailed geomorphological maps are translated, using a standardized workflow, into polygonal maps showing the potential geoconservation value of landforms. A new development is to semi-automatically extract in a GIS geomorphological information from high resolution topographical data, such as LiDAR, and combine this with conventional data types (e.g. airphotos, geological maps) into geomorphological maps. Such hybrid digital geomorphological maps are also easily translated into digital information layers which show the geoconservation potential in an area. We present a protocol for digital geomorphological mapping illustrated with an example for the municipality of Lech in Vorarlberg (Austria). The protocol consists of 5 steps: 1. data preparation, 2. generating training and validation samples, 3. parameterization, 4. feature extraction, and 5. assessing classification accuracy. The resulting semi-automated digital geomorphological map is then further validated, in two ways. Firstly, the map is manually checked with the help of a series of digital datasets (e.g. airphotos) in a digital 3D environment, such as ArcScene. The second validation is field visit, which preferably occurs in parallel to the digital evaluation, so that updates are quickly achieved. The final digital and coded geomorphological information layer is converted into a potential geoconservation map by weighting and ranking the landforms based on four criteria: scientific relevance, frequency of occurrence, disturbance, and environmental vulnerability. The criteria with predefined scores for the various landform types are stored in a separate GIS attribute table, which is joined to the attribute table of the hybrid geomorphological information layer in an automated procedure. The results of the assessment can be displayed as the potential

Multimodality language mapping in patients with left-hemispheric language dominance on Wada test.

Science.gov (United States)

Kojima, Katsuaki; Brown, Erik C; Rothermel, Robert; Carlson, Alanna; Matsuzaki, Naoyuki; Shah, Aashit; Atkinson, Marie; Mittal, Sandeep; Fuerst, Darren; Sood, Sandeep; Asano, Eishi

2012-10-01

We determined the utility of electrocorticography (ECoG) and stimulation for detecting language-related sites in patients with left-hemispheric language-dominance on Wada test. We studied 13 epileptic patients who underwent language mapping using event-related gamma-oscillations on ECoG and stimulation via subdural electrodes. Sites showing significant gamma-augmentation during an auditory-naming task were defined as language-related ECoG sites. Sites at which stimulation resulted in auditory perceptual changes, failure to verbalize a correct answer, or sensorimotor symptoms involving the mouth were defined as language-related stimulation sites. We determined how frequently these methods revealed language-related sites in the superior-temporal, inferior-frontal, dorsolateral-premotor, and inferior-Rolandic regions. Language-related sites in the superior-temporal and inferior-frontal gyri were detected by ECoG more frequently than stimulation (p hemispheric language-dominance. Measurement of language-related gamma-oscillations is warranted in presurgical evaluation of epileptic patients. Copyright © 2012 International Federation of Clinical Neurophysiology. Published by Elsevier Ireland Ltd. All rights reserved.

Documentation for Initial Seismic Hazard Maps for Haiti

Science.gov (United States)

Frankel, Arthur; Harmsen, Stephen; Mueller, Charles; Calais, Eric; Haase, Jennifer

2010-01-01

maps using different assumptions about site conditions. One set of maps is for a firm-rock site condition (30-m averaged shear-wave velocity, Vs30, of 760 m/s). We also developed hazard maps that contain site amplification based on a grid of Vs30 values estimated from topographic slope. These maps take into account amplification from soils. We stress that these new maps are designed to quantify the hazard for Haiti; they do not consider all the sources of earthquake hazard that affect the Dominican Republic and therefore should not be considered as complete hazard maps for eastern Hispaniola. For example, we have not included hazard from earthquakes in the Mona Passage nor from large earthquakes on the subduction zone interface north of Puerto Rico. Furthermore, they do not capture all the earthquake hazards for eastern Cuba.

Monitoring and mapping selected riparian habitat along the lower Snake River

Energy Technology Data Exchange (ETDEWEB)

Downs, J. L; Tiller, B. L [Pacific Northwest Lab., Richland, WA (United States); Witter, M. [Shannon and Wilson, Inc., Seattle, WA (United States). Geotechnical and Environmental Consultants, Seattle, Washington (United States); Mazaika, R. [Corps of Engineers, Portland, OR (United States)

1996-01-01

Studies in this document were initiated to establish baseline information on riparian and wetland habitat conditions at the areas studied under the current reservoir operations on the lower Snake River. Two approaches were used to assess habitat at 28 study sites selected on the four pools on the lower Snake River. These areas all contribute significant riparian habitat along the river, and several of these areas are designated habitat management units. At 14 of the 28 sites, we monitored riparian habitat on three dates during the growing season to quantify vegetation abundance and composition along three transects: soil nutrients, moisture, and pH and water level and pH. A second approach involved identifying any differences in the extent and amount of riparian/wetland habitat currently found at the study areas from that previously documented. We used both ground and boat surveys to map and classify the changes in vegetative cover along the shoreline at the 14 monitoring sites and at 14 additional sites along the lower Snake selected to represent various riparian/wetland habitat conditions. Results of these mapping efforts are compared with maps of cover types previously generated using aerial photography taken in 1987.

Geological Mapping of Investigation Trenches OL-TK15 and OL-TK16 at the Olkiluoto Study Site, Eurajoki, SW Finland

International Nuclear Information System (INIS)

Vaarma, M.; Vuokko, J.

2009-07-01

Geological mapping of investigation trenches OL-TK15 and OL-TK16 was carried out by the Geological Survey of Finland (GTK) at the Olkiluoto study site as a part of Posiva Oy's site investigation program for the development of an underground repository for nuclear waste. OL-TK15 is ca. N-S striking and ca. 95 m long, and OL-TK16 is ca. E-W striking and ca. 172 m long. The trenches were cleaned with pressure washer and pressurized air. The rock types were determined in field by naked eyes. Five samples from OL-TK15 and 10 samples from OL-TK16 were thin sectioned and investigated microscopically. In addition, petrophysical measurements were carried out by GTK geophysical laboratory for these samples. The bedrock within the excavation trenches OL-TK15 and OL-TK16 consists mainly of veined gneiss (VGN) with intercalations of mica gneiss (MGN), and mafic gneiss (MFGN) of amphibolite, amphibolite-gneiss, and skarn gneiss. The VGN is frankly solid or intact, fine grained and weakly banded and multiple intruded by granitic and pegmatitic veins and veinlets. Narrow scrappy zones occupied by dark dots of highly altered pseudomorphs after cordierite and/or garnet tend to be common in places. In addition, VGN contains rounded oblong mafic to intermediate fragments due to boudination of competent layers and/or dykes. Some rather narrow pegmatitic and quartz veins cut the previous tectonic structures. The prevailing tectonic structures are strong pervasive foliation and conformal veining of several generations mostly granitic in composition. The strike of the foliation and banding and veining as well, varies a little from NNE to ENE and the dip is ca. 40 - 50 degrees to SE sector, respectively. The younger folding has bent the older foliation and neosomic veining mostly with dextral monoclinic style so that in many places there occur tight kinky nodes and rootles augen like knots showing dextral rotation, too. Due to brittle deformation, there are some shear zones and zones with

Shear-wave velocity compilation for Northridge strong-motion recording sites

Science.gov (United States)

Borcherdt, Roger D.; Fumal, Thomas E.

2002-01-01

Borehole and other geotechnical information collected at the strong-motion recording sites of the Northridge earthquake of January 17, 1994 provide an important new basis for the characterization of local site conditions. These geotechnical data, when combined with analysis of strong-motion recordings, provide an empirical basis to evaluate site coefficients used in current versions of US building codes. Shear-wave-velocity estimates to a depth of 30 meters are derived for 176 strong-motion recording sites. The estimates are based on borehole shear-velocity logs, physical property logs, correlations with physical properties and digital geologic maps. Surface-wave velocity measurements and standard penetration data are compiled as additional constraints. These data as compiled from a variety of databases are presented via GIS maps and corresponding tables to facilitate use by other investigators.

On Quadrirational Yang-Baxter Maps

Directory of Open Access Journals (Sweden)

V.G. Papageorgiou

2010-04-01

Full Text Available We use the classification of the quadrirational maps given by Adler, Bobenko and Suris to describe when such maps satisfy the Yang-Baxter relation. We show that the corresponding maps can be characterized by certain singularity invariance condition. This leads to some new families of Yang-Baxter maps corresponding to the geometric symmetries of pencils of quadrics.

St. Louis Area Earthquake Hazards Mapping Project - A Progress Report-November 2008

Science.gov (United States)

Karadeniz, D.; Rogers, J.D.; Williams, R.A.; Cramer, C.H.; Bauer, R.A.; Hoffman, D.; Chung, J.; Hempen, G.L.; Steckel, P.H.; Boyd, O.L.; Watkins, C.M.; McCallister, N.S.; Schweig, E.

2009-01-01

St. Louis has experienced minor earthquake damage at least 12 times in the past 200 years. Because of this history and its proximity to known active earthquake zones, the St. Louis Area Earthquake Hazards Mapping Project (SLAEHMP) is producing digital maps that show variability of earthquake hazards, including liquefaction and ground shaking, in the St. Louis area. The maps will be available free via the internet. Although not site specific enough to indicate the hazard at a house-by-house resolution, they can be customized by the user to show specific areas of interest, such as neighborhoods or transportation routes. Earthquakes currently cannot be predicted, but scientists can estimate how strongly the ground is likely to shake as the result of an earthquake. Earthquake hazard maps provide one way of conveying such estimates. The U.S. Geological Survey (USGS), which produces earthquake hazard maps for the Nation, is working with local partners to develop detailed maps for urban areas vulnerable to strong ground shaking. These partners, which along with the USGS comprise the SLAEHMP, include the Missouri University of Science and Technology-Rolla (Missouri S&T), Missouri Department of Natural Resources (MDNR), Illinois State Geological Survey (ISGS), Saint Louis University, Missouri State Emergency Management Agency, and URS Corporation. Preliminary hazard maps covering a test portion of the 29-quadrangle St. Louis study area have been produced and are currently being evaluated by the SLAEHMP. A USGS Fact Sheet summarizing this project was produced and almost 1000 copies have been distributed at several public outreach meetings and field trips that have featured the SLAEHMP (Williams and others, 2007). In addition, a USGS website focusing on the SLAEHMP, which provides links to project results and relevant earthquake hazard information, can be found at: http://earthquake.usgs.gov/regional/ceus/urban_map/st_louis/index.php. This progress report summarizes the

St. John Benthic Habitat Mapping - Moderate Depth Ground Validation Sites (Mean Locations)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Benthic habitats of the moderate-depth marine environment in and around the Virgin Islands Coral Reef National Monument were mapped using a combination of...

Ordered and isomorphic mapping of periodic structures in the parametrically forced logistic map

Energy Technology Data Exchange (ETDEWEB)

Maranhão, Dariel M., E-mail: dariel@ifsp.edu.br [Departamento de Ciências e Matemática, Instituto Federal de Educação, Ciência e Tecnologia de São Paulo, São Paulo (Brazil); Diretoria de Informática, Universidade Nove de Julho, São Paulo (Brazil)

2016-09-23

Highlights: • A direct description of the internal structure of a periodic window in terms of winding numbers is proposed. • Periodic structures in parameter spaces are mapped in a recurrent and isomorphic way. • Sequences of winding numbers show global and local organization of periodic domains. - Abstract: We investigate the periodic domains found in the parametrically forced logistic map, the classical logistic map when its control parameter changes dynamically. Phase diagrams in two-parameter spaces reveal intricate periodic structures composed of patterns of intersecting superstable orbits curves, defining the cell of a periodic window. Cells appear multifoliated and ordered, and they are isomorphically mapped when one changes the map parameters. Also, we identify the characteristics of simplest cell and apply them to other more complex, discussing how the topography on parameter space is affected. By use of the winding number as defined in periodically forced oscillators, we show that the hierarchical organization of the periodic domains is manifested in global and local scales.

Using Self Organizing Maps to evaluate the NASA GISS AR5 SCM at the ARM SGP Site

Science.gov (United States)

Dong, X.; Kennedy, A. D.; Xi, B.

2010-12-01

Cluster analyses have gained popularity in recent years to establish cloud regimes using satellite and radar cloud data. These regimes can then be used to evaluate climate models or to determine what large-scale or subgrid processes are responsible for cloud formation. An alternative approach is to first classify the meteorological regimes (i.e. synoptic pattern and forcing) and then determine what cloud scenes occur. In this study, a competitive neural network known as the Self Organizing Map (SOM) is used to classify synoptic patterns over the Southern Great Plains (SGP) region to evaluate simulated clouds from the AR5 version of the NASA GISS Model E Single Column Model (SCM). In detail, 54-class SOMs have been developed using North American Regional Reanalysis (NARR) variables averaged to 2x2.5 degree latitude longitude grid boxes for a region of 7x7 grid boxes centered on the ARM SGP site. Variables input into the SOM include mean sea-level pressure and the horizontal wind components, relative humidity, and geopotential height at the 900, 500, and 300 hPa levels. These SOMs are produced for the winter (DJF), spring (MAM), summer (JJA), and fall (SON) seasons during 1999-2001. This synoptic typing will be associated with observed cloud fractions and forcing properties from the ARM SGP site and then used to evaluate simulated clouds from the SCM. SOMs provide a visually intuitive way to understand their classifications because classes are related to each other in a two-dimensional space. In Fig. 1 for example, the reader can easily see for a 54 class SOM during the winter season, classes with higher 300 hPa mean relative humidities are clustered near each other. This allows for the user to identify that there appears to be a relationship between mean 300 hPa RH and high cloud fraction as observed by the ARM SGP site. Figure 1. Mean high cloud fraction (top panel) and 300 hPa Relative Humidity (bottom panel) for a 9x6 (54 class) SOM during the winter (DJF) season

Positivity of linear maps under tensor powers

Energy Technology Data Exchange (ETDEWEB)

Müller-Hermes, Alexander, E-mail: muellerh@ma.tum.de; Wolf, Michael M., E-mail: m.wolf@tum.de [Zentrum Mathematik, Technische Universität München, 85748 Garching (Germany); Reeb, David, E-mail: reeb.qit@gmail.com [Zentrum Mathematik, Technische Universität München, 85748 Garching (Germany); Institute for Theoretical Physics, Leibniz Universität Hannover, 30167 Hannover (Germany)

2016-01-15

We investigate linear maps between matrix algebras that remain positive under tensor powers, i.e., under tensoring with n copies of themselves. Completely positive and completely co-positive maps are trivial examples of this kind. We show that for every n ∈ ℕ, there exist non-trivial maps with this property and that for two-dimensional Hilbert spaces there is no non-trivial map for which this holds for all n. For higher dimensions, we reduce the existence question of such non-trivial “tensor-stable positive maps” to a one-parameter family of maps and show that an affirmative answer would imply the existence of non-positive partial transpose bound entanglement. As an application, we show that any tensor-stable positive map that is not completely positive yields an upper bound on the quantum channel capacity, which for the transposition map gives the well-known cb-norm bound. We, furthermore, show that the latter is an upper bound even for the local operations and classical communications-assisted quantum capacity, and that moreover it is a strong converse rate for this task.

Positivity of linear maps under tensor powers

International Nuclear Information System (INIS)

Müller-Hermes, Alexander; Wolf, Michael M.; Reeb, David

2016-01-01

We investigate linear maps between matrix algebras that remain positive under tensor powers, i.e., under tensoring with n copies of themselves. Completely positive and completely co-positive maps are trivial examples of this kind. We show that for every n ∈ ℕ, there exist non-trivial maps with this property and that for two-dimensional Hilbert spaces there is no non-trivial map for which this holds for all n. For higher dimensions, we reduce the existence question of such non-trivial “tensor-stable positive maps” to a one-parameter family of maps and show that an affirmative answer would imply the existence of non-positive partial transpose bound entanglement. As an application, we show that any tensor-stable positive map that is not completely positive yields an upper bound on the quantum channel capacity, which for the transposition map gives the well-known cb-norm bound. We, furthermore, show that the latter is an upper bound even for the local operations and classical communications-assisted quantum capacity, and that moreover it is a strong converse rate for this task

GeoCF - Smart Power Maps - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Holcomb, Chris [GeoCF LLC, Austin, TX (United States)

2017-12-21

GeoCF has greatly enhanced the utility-scale solar siting platform, Smart Power Maps, through the help of the DOE Solar Energy Technologies Office. It is now available for the entire country and includes an improved user interface and additional layers such as topology, soils, comprehensive floodplains, parcels, imagery, wells, pipelines, and more. As well, users can now draw and save maps and perform drastically improved and more relevant hydrological, transmission, and financial analyzes. Smart Power Maps has played a pivotal role in supporting the development of otherwise unknown or hard to locate ideal locations for large solar farms in the United States.

Climate Prediction Center - Site Index

Science.gov (United States)

Weather Service NWS logo - Click to go to the NWS home page Climate Prediction Center Home Site Map News Means Bulletins Annual Winter Stratospheric Ozone Climate Diagnostics Bulletin (Most Recent) Climate (Hazards Outlook) Climate Assessment: Dec. 1999-Feb. 2000 (Seasonal) Climate Assessment: Mar-May 2000

Geotechnical Mapping of An-Najaf City, Iraq

Directory of Open Access Journals (Sweden)

Nadher Hassan Al-Baghdadi

2016-12-01

Full Text Available The present paper submits a set geotechnical maps for the area of An-Najaf city, by using contour lines to represent the different geotechnical properties of the soil. The present research work is very important step toward preparing a geotechnical database for this region, to complete the geotechnical database over all the country, (Iraq. Using such a database is very important in geotechincal investigation, reconnaissance phase, of construction projects. Within this phase of site investigation, numbers, depths and locations of the boreholes needed, will be determined. A well known commercial software (SURFER 11, was used to produce the all the contour maps of geotechnical properties presented herein. A forty nine (49 contour maps were produced to cover the variations, within the geotechnical properties of the soil, to produce realistic description to these soil properties. Both Google maps and Universal Transverse Mercator coordinate system (UTM have been used in the contour maps for easy use.

Geological discrete fracture network model for the Laxemar site. Site Descriptive Modelling. SDM-Site Laxemar

Energy Technology Data Exchange (ETDEWEB)

La Pointe, Paul; Fox, Aaron (Golder Associates Inc (United States)); Hermanson, Jan; Oehman, Johan (Golder Associates AB, Stockholm (Sweden))

2008-12-15

The Swedish Nuclear Fuel and Waste Management Company (SKB) is performing site characterization at two different locations, Forsmark and Laxemar, in order to locate a site for a final geologic repository for spent nuclear fuel. The program is built upon the development of Site Descriptive Models (SDMs) at specific timed data freezes. Each SDM is formed from discipline-specific reports from across the scientific spectrum. This report describes the methods, analyses, and conclusions of the modelling team in the production of the SDM-Site Laxemar geological discrete-fracture network (DFN) model. The DFN builds upon the work of other geological models, including the deformation zone and rock domain models. The geological DFN is a statistical model for stochastically simulating rock fractures and minor deformation zones at a scale of less than 1,000 m (the lower cut-off of the DZ models). The geological DFN is valid within six distinct fracture domains inside the Laxemar local model subarea: FSM{sub C}, FSM{sub E}W007, FSM{sub N}, FSM{sub N}E005, FSM{sub S}, and FSM{sub W}. The models are built using data from detailed surface outcrop maps, geophysical lineament maps, and the cored borehole record at Laxemar. The conceptual model for the SDM-Site Laxemar geological DFN model revolves around the identification of fracture domains based on relative fracture set intensities, orientation clustering, and the regional tectonic framework (including deformation zones). A single coupled fracture size/fracture intensity concept (the Base Model) based on a Pareto (power-law) distribution for fracture sizes was chosen as the recommended parameterisation. A slew of alternative size-intensity models were also carried through the fracture analyses and into the uncertainty and model verification analyses. Uncertainty is modelled by analysing the effects on fracture intensity (P32) that alternative model cases can have. Uncertainty is parameterised as a ratio between the P32 of the

Geological discrete fracture network model for the Laxemar site. Site Descriptive Modelling. SDM-Site Laxemar

International Nuclear Information System (INIS)

La Pointe, Paul; Fox, Aaron; Hermanson, Jan; Oehman, Johan

2008-10-01

The Swedish Nuclear Fuel and Waste Management Company (SKB) is performing site characterization at two different locations, Forsmark and Laxemar, in order to locate a site for a final geologic repository for spent nuclear fuel. The program is built upon the development of Site Descriptive Models (SDMs) at specific timed data freezes. Each SDM is formed from discipline-specific reports from across the scientific spectrum. This report describes the methods, analyses, and conclusions of the modelling team in the production of the SDM-Site Laxemar geological discrete-fracture network (DFN) model. The DFN builds upon the work of other geological models, including the deformation zone and rock domain models. The geological DFN is a statistical model for stochastically simulating rock fractures and minor deformation zones at a scale of less than 1,000 m (the lower cut-off of the DZ models). The geological DFN is valid within six distinct fracture domains inside the Laxemar local model subarea: FSM C , FSM E W007, FSM N , FSM N E005, FSM S , and FSM W . The models are built using data from detailed surface outcrop maps, geophysical lineament maps, and the cored borehole record at Laxemar. The conceptual model for the SDM-Site Laxemar geological DFN model revolves around the identification of fracture domains based on relative fracture set intensities, orientation clustering, and the regional tectonic framework (including deformation zones). A single coupled fracture size/fracture intensity concept (the Base Model) based on a Pareto (power-law) distribution for fracture sizes was chosen as the recommended parameterisation. A slew of alternative size-intensity models were also carried through the fracture analyses and into the uncertainty and model verification analyses. Uncertainty is modelled by analysing the effects on fracture intensity (P32) that alternative model cases can have. Uncertainty is parameterised as a ratio between the P32 of the alternative model and the P

Geologic mapping procedure: Final draft

International Nuclear Information System (INIS)

1987-09-01

Geologic mapping will provide a baseline record of the subsurface geology in the shafts and drifts of the Exploratory Shaft Facility (ESF). This information will be essential in confirming the specific repository horizon, selecting representative locations for the in situ tests, providing information for construction and decommissioning seal designs, documenting the excavation effects, and in providing information for performance assessment, which relates to the ultimate suitability of the site as a nuclear waste repository. Geologic mapping will be undertaken on the walls and roof, and locally on the floor within the completed At-Depth Facility (ADF) and on the walls of the two access shafts. Periodic mapping of the exposed face may be conducted during construction of the ADF. The mapping will be oriented toward the collection and presentation of geologic information in an engineering format and the portrayal of detailed stratigraphic information which may be useful in confirmation of drillhole data collected as part of the surface-based testing program. Geologic mapping can be considered as a predictive tool as well as a means of checking design assumptions. This document provides a description of the required procedures for geologic mapping for the ESF. Included in this procedure is information that qualified technical personnel can use to collect the required types of geologic descriptions, at the appropriate level of detail. 5 refs., 3 figs., 1 tab

Splinkerette PCR for mapping transposable elements in Drosophila.

Directory of Open Access Journals (Sweden)

Christopher J Potter

2010-04-01

Full Text Available Transposable elements (such as the P-element and piggyBac have been used to introduce thousands of transgenic constructs into the Drosophila genome. These transgenic constructs serve many roles, from assaying gene/cell function, to controlling chromosome arm rearrangement. Knowing the precise genomic insertion site for the transposable element is often desired. This enables identification of genomic enhancer regions trapped by an enhancer trap, identification of the gene mutated by a transposon insertion, or simplifying recombination experiments. The most commonly used transgene mapping method is inverse PCR (iPCR. Although usually effective, limitations with iPCR hinder its ability to isolate flanking genomic DNA in complex genomic loci, such as those that contain natural transposons. Here we report the adaptation of the splinkerette PCR (spPCR method for the isolation of flanking genomic DNA of any P-element or piggyBac. We report a simple and detailed protocol for spPCR. We use spPCR to 1 map a GAL4 enhancer trap located inside a natural transposon, pinpointing a master regulatory region for olfactory neuron expression in the brain; and 2 map all commonly used centromeric FRT insertion sites. The ease, efficiency, and efficacy of spPCR could make it a favored choice for the mapping of transposable element in Drosophila.

Demonstration of volumetric analysis using the topographical mapping system at Hanford

International Nuclear Information System (INIS)

Armstrong, G.A.; Burks, B.L.; Carteret, B.A.; Pardini, A.F.; Samuel, T.J.

1997-07-01

During the spring of 1997, the Topographical Mapping System (TMS) for hazardous and radiological environments was used to perform volumetric measurements of simulated waste in the cold test cell in the Fuel Materials and Examination Facility at the Hanford site. The TMS was used to measure the volume of five simulated waste mounds. Custom software designed by Oak Ridge National Laboratory was used to calculate the volume of waste from the surface maps supplied by the TMS. The results of the measurements were analyzed using the Interactive Computer-Enhanced Remote-Viewing System (ICERVS) and were documented. Development of the TMS and ICERVS was initiated by the US Department of Energy (DOE) for the purpose of characterization and remediation of underground storage tanks (USTs) at DOE sites across the country. DOE required a three-dimensional TMS suitable for use in hazardous and radiological environments. The intended application is the mapping of the interior of USTs as part of DOE's waste characterization and remediation efforts to obtain baseline data on the content of storage tank interiors as well as on changes in the tank contents and levels brought about by waste remediation steps. Initially targeted for deployment at the Hanford site, the TMS was designed to be a self-contained, compact, and reconfigurable system that is capable of providing rapid, variable-resolution mapping information in poorly characterized workspaces with a minimum of operator intervention. An appendix contains the source code for calculating the volume from two surface maps

Quantitative maps of groundwater resources in Africa

International Nuclear Information System (INIS)

MacDonald, A M; Bonsor, H C; Dochartaigh, B É Ó; Taylor, R G

2012-01-01

In Africa, groundwater is the major source of drinking water and its use for irrigation is forecast to increase substantially to combat growing food insecurity. Despite this, there is little quantitative information on groundwater resources in Africa, and groundwater storage is consequently omitted from assessments of freshwater availability. Here we present the first quantitative continent-wide maps of aquifer storage and potential borehole yields in Africa based on an extensive review of available maps, publications and data. We estimate total groundwater storage in Africa to be 0.66 million km 3 (0.36–1.75 million km 3 ). Not all of this groundwater storage is available for abstraction, but the estimated volume is more than 100 times estimates of annual renewable freshwater resources on Africa. Groundwater resources are unevenly distributed: the largest groundwater volumes are found in the large sedimentary aquifers in the North African countries Libya, Algeria, Egypt and Sudan. Nevertheless, for many African countries appropriately sited and constructed boreholes can support handpump abstraction (yields of 0.1–0.3 l s −1 ), and contain sufficient storage to sustain abstraction through inter-annual variations in recharge. The maps show further that the potential for higher yielding boreholes ( > 5 l s −1 ) is much more limited. Therefore, strategies for increasing irrigation or supplying water to rapidly urbanizing cities that are predicated on the widespread drilling of high yielding boreholes are likely to be unsuccessful. As groundwater is the largest and most widely distributed store of freshwater in Africa, the quantitative maps are intended to lead to more realistic assessments of water security and water stress, and to promote a more quantitative approach to mapping of groundwater resources at national and regional level. (letter)

Catheter Ablation of a Complex Atrial Tachycardia after Surgical Repair of Tetralogy of Fallot Guided by Combined Noncontact and Contact Mapping

Directory of Open Access Journals (Sweden)

Eitaro Fujii, MD

2010-01-01

Full Text Available A 34-year-old man with a surgically repaired Tetralogy of Fallot complained of palpitation, fatigue, and presyncope. A 12-lead ECG showed atrial tachycardia with a cycle length of 250 ms and a P wave morphology positive in leads II, III and aVF, and negative in lead V1. Although the EnSite system (version 6.OJ made use of noncontact mapping to delineate the counterclockwise reentry around the crista tenninalis, it was difficult to rule out the incisional atrial reentry because the location of the surgical incision was far from the multi-electrode array. Since the bipolar contact mapping of the EnSite system revealed the location of the atriotomy incision, entrainment mapping during the tachycardia demonstrated the critical reentry circuit around the crista terminalis. Radiofrequency ablation targeting the critical isthmus from the lower position of the crista terminalis to the posterior dense scar which was continuous with the inferior vena cava, and to the atriotomy scar, eliminated the tachycardia.

SITE-2, Power Plant Siting, Cost, Environment, Seismic and Meteorological Effects

International Nuclear Information System (INIS)

Frigerio, N.A.; Habegger, L.J.; King, R.F.; Hoover, L.J.; Clark, N.A.; Cobian, J.M.

1977-01-01

1 - Description of problem or function: SITE2 is designed to (1) screen candidate energy facility sites or areas within an electric utility region, based on the region's physical and socioeconomic attributes, the planned facility's characteristics, and impact assessments, and (2) evaluate the cumulative regional impacts associated with alternate energy supply options and inter-regional energy import/export practices, specifically, comparison of different energy technologies and their regional distribution in clustered or dispersed patterns. 2 - Method of solution: The SITE2 methodology is based on the quantification of three major site-related vectors. A cost vector is determined which identifies site-specific costs, such as transmission costs, cooling costs as related to water availability, and costs of specific controls needed to protect the surrounding environment. An impact vector is also computed for each potential site, using models of health and environmental impacts incurred in areas adjacent to the site. Finally, a site attribute vector is developed which reflects such characteristics as population, seismic conditions, meteorology, land use, and local ecological systems. This vector can be used to eliminate certain sites because of their inability to satisfy specific constraints. These three vectors can be displayed as density maps and combined in a simple overlay approach, similar to that developed by I. L. McHarg in reference 2, to identify candidate sites. Alternatively, the vector elements can be computationally combined into a weighted sum to obtain quantitative indicators of site suitability

SITE-2, Power Plant Siting, Cost, Environment, Seismic and Meteorological Effects

Energy Technology Data Exchange (ETDEWEB)

Frigerio, N A [Environmental Impact Studies, Argonne National Laboratory 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Habegger, L J; King, R F; Hoover, L J [Energy and Environmental Systems Division, Argonne National Laboratory 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Clark, N A [Applied Mathematics Division, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Cobian, J M [Northwestern University, Evanston, Illinois 60201 (United States)

1977-08-01

1 - Description of problem or function: SITE2 is designed to (1) screen candidate energy facility sites or areas within an electric utility region, based on the region's physical and socioeconomic attributes, the planned facility's characteristics, and impact assessments, and (2) evaluate the cumulative regional impacts associated with alternate energy supply options and inter-regional energy import/export practices, specifically, comparison of different energy technologies and their regional distribution in clustered or dispersed patterns. 2 - Method of solution: The SITE2 methodology is based on the quantification of three major site-related vectors. A cost vector is determined which identifies site-specific costs, such as transmission costs, cooling costs as related to water availability, and costs of specific controls needed to protect the surrounding environment. An impact vector is also computed for each potential site, using models of health and environmental impacts incurred in areas adjacent to the site. Finally, a site attribute vector is developed which reflects such characteristics as population, seismic conditions, meteorology, land use, and local ecological systems. This vector can be used to eliminate certain sites because of their inability to satisfy specific constraints. These three vectors can be displayed as density maps and combined in a simple overlay approach, similar to that developed by I. L. McHarg in reference 2, to identify candidate sites. Alternatively, the vector elements can be computationally combined into a weighted sum to obtain quantitative indicators of site suitability.

Multitemporal Accuracy and Precision Assessment of Unmanned Aerial System Photogrammetry for Slope-Scale Snow Depth Maps in Alpine Terrain

Science.gov (United States)

Adams, Marc S.; Bühler, Yves; Fromm, Reinhard

2017-12-01

Reliable and timely information on the spatio-temporal distribution of snow in alpine terrain plays an important role for a wide range of applications. Unmanned aerial system (UAS) photogrammetry is increasingly applied to cost-efficiently map the snow depth at very high resolution with flexible applicability. However, crucial questions regarding quality and repeatability of this technique are still under discussion. Here we present a multitemporal accuracy and precision assessment of UAS photogrammetry for snow depth mapping on the slope-scale. We mapped a 0.12 km2 large snow-covered study site, located in a high-alpine valley in Western Austria. 12 UAS flights were performed to acquire imagery at 0.05 m ground sampling distance in visible (VIS) and near-infrared (NIR) wavelengths with a modified commercial, off-the-shelf sensor mounted on a custom-built fixed-wing UAS. The imagery was processed with structure-from-motion photogrammetry software to generate orthophotos, digital surface models (DSMs) and snow depth maps (SDMs). Accuracy of DSMs and SDMs were assessed with terrestrial laser scanning and manual snow depth probing, respectively. The results show that under good illumination conditions (study site in full sunlight), the DSMs and SDMs were acquired with an accuracy of ≤ 0.25 and ≤ 0.29 m (both at 1σ), respectively. In case of poorly illuminated snow surfaces (study site shadowed), the NIR imagery provided higher accuracy (0.19 m; 0.23 m) than VIS imagery (0.49 m; 0.37 m). The precision of the UASSDMs was 0.04 m for a small, stable area and below 0.33 m for the whole study site (both at 1σ).

Land-cover mapping using multitemporal, dual-frequency polarimetric SAR data

DEFF Research Database (Denmark)

Skriver, Henning; Schou, Jesper; Dierking, Wolfgang

2000-01-01

during the growing season acquired a lot of data over a Danish agricultural site. The data acquisitions were co-ordinated with ground surveys to obtain a detailed land cover map. The test area contains a large number of different land cover classes, such as more than 10 different crop types, deciduous......The Danish Center for Remote Sensing (DCRS) is, in collaboration with the Danish mapping agency, conducting a study on topographic mapping using SAR data, and land cover mapping results are presented. The Danish EMISAR system (an L- and C-band, fully polarimetric, airborne SAR) have in 1994 to 1999...

Geological mapping of investigation trench OL-TK14 at the Olkiluoto study site, Eurajoki, SW Finland

International Nuclear Information System (INIS)

Nordbaeck, N.

2007-12-01

Geological mapping of investigation trench OL-TK14 was carried out by the Geological Survey of Finland at the Olkiluoto study site, Eurajoki, as part of Posiva Oy's site investigation programme for the development of an underground repository for nuclear waste. The E-W striking, ca. 215 m long trench is located in the eastern part of the Olkiluoto Island adjacent to boreholes OL-KR40 and OL-KR45. The trench was cleaned with a pressure washer and pressurized air. The rock types were determined macroscopically. Five samples were also investigated microscopically. The main rock type in the trench is veined gneiss. A few less than 0.5 m wide coarsegrained pegmatitic granite dykes are also encountered. Furthermore a large number of mica gneiss, quartz gneiss and skarn inclusions are present in the veined gneiss, being often elongated and parallel to the foliation. The most dominant tectonic feature is the foliation S2 and associated intense granitic leucosome veining. The foliation strikes ENE-WSW and dips steeply towards SES. Intensely to moderately banded rocks dominate the trench. The sparse F3 folds observed in OL-TK14 are small-scale tight folds in leucosome veins. A large-scale (10 m) open bending of the foliation that could be a result of D4 folding was also observed. Shearbands and other signs of ductile shearing were observed on many locations in the trench and in the eastern part there is a high-grade ductile shear zone intersection. During the fracture mapping, all fractures intersecting the central thread were investigated and a total of 684 fractures were recorded. The average fracture density of the trench is 3.18 fractures/m. On the basis of fracture orientations three main sets can be distinguished: 1) a set striking N-S with vertical dip, 2) a ENE-WSW striking set with varying dips towards the SSE (parallel to the foliation) and 3) a NE-SW striking set with sub-vertical dip towards the SE or the NW. Most of the measured fractures are short due to the

Performance of non-parametric algorithms for spatial mapping of tropical forest structure

Directory of Open Access Journals (Sweden)

Liang Xu

2016-08-01

Full Text Available Abstract Background Mapping tropical forest structure is a critical requirement for accurate estimation of emissions and removals from land use activities. With the availability of a wide range of remote sensing imagery of vegetation characteristics from space, development of finer resolution and more accurate maps has advanced in recent years. However, the mapping accuracy relies heavily on the quality of input layers, the algorithm chosen, and the size and quality of inventory samples for calibration and validation. Results By using airborne lidar data as the “truth” and focusing on the mean canopy height (MCH as a key structural parameter, we test two commonly-used non-parametric techniques of maximum entropy (ME and random forest (RF for developing maps over a study site in Central Gabon. Results of mapping show that both approaches have improved accuracy with more input layers in mapping canopy height at 100 m (1-ha pixels. The bias-corrected spatial models further improve estimates for small and large trees across the tails of height distributions with a trade-off in increasing overall mean squared error that can be readily compensated by increasing the sample size. Conclusions A significant improvement in tropical forest mapping can be achieved by weighting the number of inventory samples against the choice of image layers and the non-parametric algorithms. Without future satellite observations with better sensitivity to forest biomass, the maps based on existing data will remain slightly biased towards the mean of the distribution and under and over estimating the upper and lower tails of the distribution.

A new map of global urban extent from MODIS satellite data

International Nuclear Information System (INIS)

Schneider, A; Friedl, M A; Potere, D

2009-01-01

Although only a small percentage of global land cover, urban areas significantly alter climate, biogeochemistry, and hydrology at local, regional, and global scales. To understand the impact of urban areas on these processes, high quality, regularly updated information on the urban environment-including maps that monitor location and extent-is essential. Here we present results from efforts to map the global distribution of urban land use at 500 m spatial resolution using remotely sensed data from the Moderate Resolution Imaging Spectroradiometer (MODIS). Our approach uses a supervised decision tree classification algorithm that we process using region-specific parameters. An accuracy assessment based on sites from a stratified random sample of 140 cities shows that the new map has an overall accuracy of 93% (k = 0.65) at the pixel level and a high level of agreement at the city scale (R 2 = 0.90). Our results (available at http://sage.wisc.edu/urbanenvironment.html) also reveal that the land footprint of cities occupies less than 0.5% of the Earth's total land area.

Map Showing Geology and Hydrostratigraphy of the Edwards Aquifer Catchment Area, Northern Bexar County, South-Central Texas

Science.gov (United States)

Clark, Amy R.; Blome, Charles D.; Faith, Jason R.

2009-01-01

Rock units forming the Edwards and Trinity aquifers in northern Bexar County, Texas, are exposed within all or parts of seven 7.5-minute quadrangles: Bulverde, Camp Bullis, Castle Hills, Helotes, Jack Mountain, San Geronimo, and Van Raub. The Edwards aquifer is the most prolific ground-water source in Bexar County, whereas the Trinity aquifer supplies water for residential, commercial, and industrial uses for areas north of the San Antonio. The geologic map of northern Bexar County shows the distribution of informal hydrostratigraphic members of the Edwards Group and the underlying upper member of the Glen Rose Limestone. Exposures of the Glen Rose Limestone, which forms the Trinity aquifer alone, cover approximately 467 km2 in the county. This study also describes and names five informal hydrostratigraphic members that constitute the upper member of the Glen Rose Limestone; these include, in descending order, the Caverness, Camp Bullis, Upper evaporite, Fossiliferous, and Lower evaporite members. This study improves our understanding of the hydrogeologic connection between the two aquifers as it describes the geology that controls the infiltration of surface water and subsurface flow of ground water from the catchment area (outcropping Trinity aquifer rocks) to the Edwards water-bearing exposures.

Harmonic maps of the hyperbolic space and development of singularities in wave maps and Yang-Mills fields

International Nuclear Information System (INIS)

Cazenave, T.; Shatah, J.; Tahvildar-Zadeh, A.S.

1998-01-01

In this article we explore some of the connections between the theories of Yang-Mills fields, wave maps, and harmonic maps. It has been shown that the search for similarity solutions of wave maps leads to harmonic maps of the hyperbolic space. On the other hand, Glassey and Strauss have shown that the equations for an SO(3)-equivariant Yang-Mills connection on the Minkowski space R 3,1 with gauge group SU(2) reduce to a certain nonlinear wave equation, which we can now identify as a wave map on R 1,1 . More generally, we will here show the reduction under equivariance of a Yang-Mills system on the Minkowski space R n,1 to a wave map system on R n-2,1 in the specific case of SO(n) bundles with SO(n) symmetry. We then prove for odd n the existence of equivariant harmonic maps from the hyperbolic space H n that are smooth at the ideal boundary of H n , thus establishing the existence of similarity solutions for equivariant wave maps and Yang-Mills fields. As a consequence we show that for n ≥ 7, it is possible to have a wave map into a negatively curved target manifold that develops from smooth initial data and blows up in finite time, in sharp contrast to the elliptic case of harmonic maps. Finally we show how these singular solutions can be lifted to one dimension higher to produce singular travelling waves. (orig.)

MapCERN: the CERN map on your mobile

CERN Multimedia

Anaïs Schaeffer

2011-01-01

On the initiative of the GS Department, a new smartphone application called MapCERN has just been released. Available in two different versions – one from the Apple Store for iPhones and the other from the web for Android and Blackberry – it will help you to find the building you're looking for more easily.     The Globe of Science and Innovation as "seen" in the augmented reality of the iPhone.  You've got an appointment with someone at the other end of the CERN site and you're planning to use the CERN map to find your way there but you suddenly realise you've left it in your office… No need to panic! Simply take out your smartphone and let it guide you to the building you're looking for. This first official CERN application, which has been developed by the GS Department in collaboration with private industry, is available free of charge from the Apple Store in the case of iPhones an...

Hyperspectral surface materials map of quadrangle 3260, Dasht-e-Chah-e-Mazar (419) and Anar Darah (420) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

Science.gov (United States)

King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

2013-01-01

This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

Detecting coevolving amino acid sites using Bayesian mutational mapping

DEFF Research Database (Denmark)