Savannah River Site Ingestion Pathway Methodology Manual for Airborne Radioactive Releases

Energy Technology Data Exchange (ETDEWEB)

Vincent, A.W. III

2001-01-03

This manual documents a recommended methodology for determining the ingestion pathway consequences of hypothetical accidental airborne radiological releases from facilities at the Savannah River Site. Both particulate and tritiated radioactive contaminants are addressed. Other approaches should be applied for evaluation of routine releases.

Site security personnel training manual

International Nuclear Information System (INIS)

1978-10-01

As required by 10 CFR Part 73, this training manual provides guidance to assist licensees in the development of security personnel training and qualifications programs. The information contained in the manual typifies the level and scope of training for personnel assigned to perform security related tasks and job duties associated with the protection of nuclear fuel cycle facilities and nuclear power reactors

Manual for investigation and correction of feedwater heater failures

International Nuclear Information System (INIS)

Bell, R.J.; Diaz-Tous, I.A.; Bartz, J.A.

1993-01-01

The Electric Power Research Institute (EPRI) has sponsored the development of a recently published manual which is designed to assist utility personnel in identifying and correcting closed feedwater heater problems. The main portion of the manual describes common failure modes, probable means of identifying root causes and appropriate corrective actions. These include materials selection, fabrication practices, design, normal/abnormal operation and maintenance. The manual appendices include various data, intended to aid those involved in monitoring and condition assessment of feedwater heaters. This paper contains a detailed overview of the manual content and suggested means for its efficient use by utility engineers and operations and maintenance personnel who are charged with the responsibilities of performing investigations to identify the root cause(s) of closed feedwater problems/failures and to provide appropriate corrective actions. 4 refs., 3 figs., 2 tabs

Survey Procedures Manual for the Environmental Survey and Site Assessment Program (ESSAP). Revision 10

International Nuclear Information System (INIS)

2000-01-01

The Environmental Survey and Site Assessment Program (ESSAP) of the Oak Ridge Institute for Science and Education (ORISE) conducts radiological survey activities under a contract with the U. S. Department of Energy (DOE) and for the U.S. Nuclear Regulatory Commission (NRC). ORISE and its programs are operated by Oak Ridge Associated Universities (ORAU) through a contract with DOE. The purpose of this Procedures Manual is to provide a standardized set of procedures that document activities of the program in an auditable manner. These procedures are applicable to both DOE and NRC operations. Procedures presented in this manual are limited to those associated with site survey activities

Operations and Maintenance Manual for Expanded Bioventing System Site FC-2 Kelly AFB, Texas

National Research Council Canada - National Science Library

1996-01-01

This Operations and Maintenance Manual has been created as a guide for monitoring and maintaining the performance of the bioventing blower and vent well plumbing at the Fire Training Area (Site FC-2...

Use of toxicity assessment to develop site specific remediation criteria for oil and gas facilities : guidance manual

International Nuclear Information System (INIS)

1996-01-01

The results of a two year study into the evaluation of toxicity-based methods to develop site-specific, risk-based cleanup objectives for the decommissioning of oil and gas facilities were compiled into a manual of guidance. The two basic approaches used in determining remediation criteria for contaminated sites are: (1) comparison of the concentrations of chemicals found on-site with broad regional or national soil and water quality objectives developed for the chemicals involved, and (2) site-specific risk assessment. Toxicity tests are used to test organisms such as earthworms, lettuce seeds, or larval fish directly in the soil, water or sediment suspected of being contaminated. The effects of any contamination on the survival, growth, reproduction, and behaviour of the test organisms are then evaluated. The manual provides guidance in: (1) using toxicity assessments within the regulatory framework of site decommissioning, (2) performing a toxicity assessment, and (3) developing site-specific criteria for a risk assessment. 18 refs., 3 tabs., 5 figs

75 FR 52976 - Issuance of Revised Users' Manual for Commission Mediation Program for Investigations Under...

Science.gov (United States)

2010-08-30

... INTERNATIONAL TRADE COMMISSION Issuance of Revised Users' Manual for Commission Mediation Program... 65615 (Nov. 8, 2008). The Commission has determined to issue a revised Users' Manual for its program for the mediation of investigations under section 337 of the Tariff Act of 1930. The revised Users' Manual...

Site investigations. Investigation methods and general execution programme

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-01-01

SKB plans to commence site investigations in 2002. The present report is a broadening of the general programme and describes the execution of the investigations in so-called discipline-specific programmes for the disciplines geology, rock mechanics, thermal properties, hydrogeology, hydro geochemistry, transport properties of the rock and surface ecosystems. It also describes various technical aspects of drilling, which comprises a significant portion of the investigations. Based on this possible programme, site-specific programmes will then be prepared and adapted to the site-specific questions and conditions on the specific candidate area. The main product of the investigations is a site description. This document presents an integrated description of the site (geosphere and biosphere) and its regional environs with respect to current state and naturally ongoing processes. Provided that the initial site investigation shows that the site is still favourable, complete investigations are commenced. Primary investigation data are stored in SKB's database SICADA. The database's primary data mainly represent parameter values for single measurement points or limited measurement objects. Primary data are subjected to both discipline-specific and integrated analysis and interpretation in order to be able to subdivide the site into suitable geometric units and to assign discipline-specific properties to these geometric units. In this way a three-dimensional, primarily geo scientific, site-descriptive model of rock and ground is built. The site-descriptive model is represented with the aid of both geographic information systems (GIS) and above all SKB's CAD-based computer tool, Rock Visualization System (RVS). RVS is also used as an active instrument in the interpretation of information, especially to be able to judge the relative locations of different deformation zones. When the site has been selected, the investigations are focused on characterizing

Radiological Control Manual

Energy Technology Data Exchange (ETDEWEB)

1993-04-01

This manual has been prepared by Lawrence Berkeley Laboratory to provide guidance for site-specific additions, supplements, and clarifications to the DOE Radiological Control Manual. The guidance provided in this manual is based on the requirements given in Title 10 Code of Federal Regulations Part 835, Radiation Protection for Occupational Workers, DOE Order 5480.11, Radiation Protection for Occupational Workers, and the DOE Radiological Control Manual. The topics covered are (1) excellence in radiological control, (2) radiological standards, (3) conduct of radiological work, (4) radioactive materials, (5) radiological health support operations, (6) training and qualification, and (7) radiological records.

Radiological Control Manual

International Nuclear Information System (INIS)

1993-04-01

This manual has been prepared by Lawrence Berkeley Laboratory to provide guidance for site-specific additions, supplements, and clarifications to the DOE Radiological Control Manual. The guidance provided in this manual is based on the requirements given in Title 10 Code of Federal Regulations Part 835, Radiation Protection for Occupational Workers, DOE Order 5480.11, Radiation Protection for Occupational Workers, and the DOE Radiological Control Manual. The topics covered are (1) excellence in radiological control, (2) radiological standards, (3) conduct of radiological work, (4) radioactive materials, (5) radiological health support operations, (6) training and qualification, and (7) radiological records

Tubular wells perforation manual for investigation and training of Guarani Aquifer System

International Nuclear Information System (INIS)

2007-01-01

The Environmental protection and sustainable development of the Aquifer Guarani System project is a initiative by Argentina, Brasil, Paraguay y Uruguay with the aim to raise the knowledge, legal and institutional sustainable management from 2003-2008 period. The Guarani consortium integrated by Tahal Engineers Ltda.(Israel), SEINCO SRL. (Uruguay), Hidrocontrol S:A:(Paraguay), Arcadis Hidroambiente S.A. (Argentina) have shown in Tubular wells perforation for investigation and training of Guarani Aquifer System manual their first product. This Manual includes technical especifications focused in Guarani Aquifer System harmessing building

Site investigations. Investigation methods and general execution programme

International Nuclear Information System (INIS)

2001-01-01

SKB plans to commence site investigations in 2002. The present report is a broadening of the general programme and describes the execution of the investigations in so-called discipline-specific programmes for the disciplines geology, rock mechanics, thermal properties, hydrogeology, hydro geochemistry, transport properties of the rock and surface ecosystems. It also describes various technical aspects of drilling, which comprises a significant portion of the investigations. Based on this possible programme, site-specific programmes will then be prepared and adapted to the site-specific questions and conditions on the specific candidate area. The main product of the investigations is a site description. This document presents an integrated description of the site (geosphere and biosphere) and its regional environs with respect to current state and naturally ongoing processes. Provided that the initial site investigation shows that the site is still favourable, complete investigations are commenced. Primary investigation data are stored in SKB's database SICADA. The database's primary data mainly represent parameter values for single measurement points or limited measurement objects. Primary data are subjected to both discipline-specific and integrated analysis and interpretation in order to be able to subdivide the site into suitable geometric units and to assign discipline-specific properties to these geometric units. In this way a three-dimensional, primarily geo scientific, site-descriptive model of rock and ground is built. The site-descriptive model is represented with the aid of both geographic information systems (GIS) and above all SKB's CAD-based computer tool, Rock Visualization System (RVS). RVS is also used as an active instrument in the interpretation of information, especially to be able to judge the relative locations of different deformation zones. When the site has been selected, the investigations are focused on characterizing conditions at depth

Site investigations for the disposal of spent fuel - investigation program

International Nuclear Information System (INIS)

Aeikaes, Timo

1985-11-01

The Industrial Power Company Ltd (TVO) is making preparations for the final disposal of spent nuclear fuel into the Finnish bedrock. The revised site investigation program for the years 1986-2010 is presented in this report. The objectives and activities in the near future are described in more detail. The main objectives and frame programs for the investigations in the more distant future are described. The program planning of these investigations are being developed in the preceding site investigations. The investigations for the site selection are divided into four phases: 1983-1985 selection of the investigation areas, preparations for the field investigations, drilling and investigations in a deep test borehole; 1986-1992 preliminary site investigations in 5-10 investigation areas; 1993-2000 detailed site investigations in 2-3 investigation areas. Site selection in the year 2000; 2001-2010 complementary investigations on the selected site. The first investigation phase will be carried out as planned. In this phase a 1001 m deep test borehole was drilled at Lavia in western Finland. With the investigations in the borehole and related development work, preparations were made for the future field investigations. The equipment and investigation methods are being developed during the site investigations. The equipment for taking groundwater samples and the unit for hydraulic testing have been developed. In the future the emphasis in the work will be in developing equipment for monitoring of the hydraulic head and measuring the volumetric flow. In groundwater sampling the present procedure can be improved by adding the test for the in-situ measurements. The results of the field investigations will be stored and processed in a centralized data base. The data base will transmit the results for the interpretation and then the interpreted results transmitted for model calculations and reporting. The cost estimate for the investigations in 1986-2010 is 110-125 million

Forsmark site investigation. Programme for long-term observations of geosphere and biosphere after completed site investigations

International Nuclear Information System (INIS)

2007-06-01

The site investigation at Forsmark was terminated the last of June, 2007. Hundreds of investigations have been conducted during a period of more than five years. Monitoring of a number of geoscientific parameters and biological objects has been one important part of the site investigation programme. Monitoring is defined as recurrent measurements of the same parameters/objects, so that time series are generated. Long-term monitoring of for example weather parameters, surface water discharge in brooks, and the groundwater head in a large number of boreholes has been conducted during the site investigations. Furthermore, repeated sampling of precipitation, surface water and groundwater in soil and rock for hydrochemical analyses has been carried out, and the groundwater flow in isolated borehole sections has been measured several times. Besides, some biological objects, for example rare bird species, have been invented each year of the site investigation. The measured parameters and the invented objects are characterized by a certain degree of time dependent variability, which is also site-specific. The aim of the monitoring is primarily to establish the 'undisturbed' conditions, the so called 'baseline'. If a deep repository is sited at Forsmark, many site-specific conditions will change, due to natural causes as well as to the construction works. Knowledge about the undisturbed conditions strengthens the ability to reveal and quantify such changes and to distinguish natural changes from those caused by the human activities. Another object of monitoring is to, by the study of the variability pattern of the monitored parameters, elevate the knowledge about the underlying, often complex causes governing the variations. In this way the description of site-specific conditions may be more precise and the prospects of modelling important processes are improved. After completion of the site investigations, a period of about two years will follow, when the investigation

Forsmark site investigation. Programme for long-term observations of geosphere and biosphere after completed site investigations

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-06-15

The site investigation at Forsmark was terminated the last of June, 2007. Hundreds of investigations have been conducted during a period of more than five years. Monitoring of a number of geoscientific parameters and biological objects has been one important part of the site investigation programme. Monitoring is defined as recurrent measurements of the same parameters/objects, so that time series are generated. Long-term monitoring of for example weather parameters, surface water discharge in brooks, and the groundwater head in a large number of boreholes has been conducted during the site investigations. Furthermore, repeated sampling of precipitation, surface water and groundwater in soil and rock for hydrochemical analyses has been carried out, and the groundwater flow in isolated borehole sections has been measured several times. Besides, some biological objects, for example rare bird species, have been invented each year of the site investigation. The measured parameters and the invented objects are characterized by a certain degree of time dependent variability, which is also site-specific. The aim of the monitoring is primarily to establish the 'undisturbed' conditions, the so called 'baseline'. If a deep repository is sited at Forsmark, many site-specific conditions will change, due to natural causes as well as to the construction works. Knowledge about the undisturbed conditions strengthens the ability to reveal and quantify such changes and to distinguish natural changes from those caused by the human activities. Another object of monitoring is to, by the study of the variability pattern of the monitored parameters, elevate the knowledge about the underlying, often complex causes governing the variations. In this way the description of site-specific conditions may be more precise and the prospects of modelling important processes are improved. After completion of the site investigations, a period of about two years will follow, when

An Investigation of Bilateral Symmetry During Manual Wheelchair Propulsion.

Science.gov (United States)

Soltau, Shelby L; Slowik, Jonathan S; Requejo, Philip S; Mulroy, Sara J; Neptune, Richard R

2015-01-01

Studies of manual wheelchair propulsion often assume bilateral symmetry to simplify data collection, processing, and analysis. However, the validity of this assumption is unclear. Most investigations of wheelchair propulsion symmetry have been limited by a relatively small sample size and a focus on a single propulsion condition (e.g., level propulsion at self-selected speed). The purpose of this study was to evaluate bilateral symmetry during manual wheelchair propulsion in a large group of subjects across different propulsion conditions. Three-dimensional kinematics and handrim kinetics along with spatiotemporal variables were collected and processed from 80 subjects with paraplegia while propelling their wheelchairs on a stationary ergometer during three different conditions: level propulsion at their self-selected speed (free), level propulsion at their fastest comfortable speed (fast), and propulsion on an 8% grade at their level, self-selected speed (graded). All kinematic variables had significant side-to-side differences, primarily in the graded condition. Push angle was the only spatiotemporal variable with a significant side-to-side difference, and only during the graded condition. No kinetic variables had significant side-to-side differences. The magnitudes of the kinematic differences were low, with only one difference exceeding 5°. With differences of such small magnitude, the bilateral symmetry assumption appears to be reasonable during manual wheelchair propulsion in subjects without significant upper-extremity pain or impairment. However, larger asymmetries may exist in individuals with secondary injuries and pain in their upper extremity and different etiologies of their neurological impairment.

Nevada Test Site Radiological Control Manual

International Nuclear Information System (INIS)

2009-01-01

This document supersedes DOE/NV/11718--079, 'NV/YMP Radiological Control Manual,' Revision 5 issued in November 2004. Brief Description of Revision: A complete revision to reflect the recent changes in compliance requirements with 10 CFR 835, and for use as a reference document for Tenant Organization Radiological Protection Programs.

Nevada Test Site Radiological Control Manual

Energy Technology Data Exchange (ETDEWEB)

Radiological Control Managers' Council - Nevada Test Site

2009-10-01

This document supersedes DOE/NV/11718--079, “NV/YMP Radiological Control Manual,” Revision 5 issued in November 2004. Brief Description of Revision: A complete revision to reflect the recent changes in compliance requirements with 10 CFR 835, and for use as a reference document for Tenant Organization Radiological Protection Programs.

Development of the NRC`s Human Performance Investigation Process (HPIP). Volume 2, Investigators`s Manual

Energy Technology Data Exchange (ETDEWEB)

Paradies, M.; Unger, L. [System Improvements, Inc., Knoxville, TN (United States); Haas, P.; Terranova, M. [Concord Associates, Inc., Knoxville, TN (United States)

1993-10-01

The three volumes of this report detail a standard investigation process for use by US Nuclear Regulatory Commission (NRC) personnel when investigating human performance related events at nuclear power plants. The process, called the Human Performance Investigation Process (HPIP), was developed to meet the special needs of NRC personnel, especially NRC resident and regional inspectors. HPIP is a systematic investigation process combining current procedures and field practices, expert experience, NRC human performance research, and applicable investigation techniques. The process is easy to learn and helps NRC personnel perform better field investigations of the root causes of human performance problems. The human performance data gathered through such investigations provides a better understanding of the human performance issues that cause event at nuclear power plants. This document, Volume II, is a field manual for use by investigators when performing event investigations. Volume II includes the HPIP Procedure, the HPIP Modules, and Appendices that provide extensive documentation of each investigation technique.

NV/YMP RADIOLOGICAL CONTROL MANUAL

Energy Technology Data Exchange (ETDEWEB)

U.S. DEPARTMENT OF ENERGY, NATIONAL NUCLEAR SECURITY ADMINISTRATION NEVADA SITE OFFICE; BECHTEL NEVADA

2004-11-01

This manual contains the radiological control requirements to be used for all radiological activities conducted by programs under the purview of the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) and the Yucca Mountain Office of Repository Development (YMORD). Compliance with these requirements will ensure compliance with Title 10 Code of Federal Regulations Part 835 (10 CFR 835), Occupational Radiation Protection. Programs covered by this manual are located at the Nevada Test Site (NTS); Nellis Air Force Base and North Las Vegas, Nevada; Santa Barbara and Pleasanton, California; and at Andrews Air Force Base, Maryland. In addition, field work by NNSA/NSO at other locations is also covered by this manual.

NV/YMP RADIOLOGICAL CONTROL MANUAL

International Nuclear Information System (INIS)

2004-01-01

This manual contains the radiological control requirements to be used for all radiological activities conducted by programs under the purview of the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) and the Yucca Mountain Office of Repository Development (YMORD). Compliance with these requirements will ensure compliance with Title 10 Code of Federal Regulations Part 835 (10 CFR 835), Occupational Radiation Protection. Programs covered by this manual are located at the Nevada Test Site (NTS); Nellis Air Force Base and North Las Vegas, Nevada; Santa Barbara and Pleasanton, California; and at Andrews Air Force Base, Maryland. In addition, field work by NNSA/NSO at other locations is also covered by this manual

Forsmark site investigation. Programme for further investigations of geosphere and biosphere

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-01-01

Since the beginning of 2002, SKB (the Swedish Nuclear Fuel and Waste Management Co) has been conducting a site investigation in Forsmark in the municipality of Oesthammar for siting of the deep repository for spent nuclear fuel. An equivalent investigation is also being conducted at Simpevarp and Laxemar in Oskarshamn Municipality. SKB's goal is to submit an application under the Environmental Code and the Nuclear Activities Act for siting of the deep repository at one of these sites by the end of 2008/beginning of 2009. When the application is submitted, everything of importance for the deep repository's safety, constructability and environmental impact shall have been investigated and analyzed. The investigations shall also provide data as a basis for selecting a site and configuring the facility to suit conditions on the site.SKB submitted a programme for the initial site investigation in Forsmark at the end of 2001. The investigations described there have now been completed. This report describes the programme that has now been prepared for the remainder of the site investigation. The points of departure are the general goals for the Deep Repository Project during the site investigation phase, the data needed for evaluation of the site, plus experience and results from the work to date. The programme has been prepared with the support of investigation data as of August 2004. The investigations described here will, as before, be conducted with great consideration given to residents, property owners and natural and cultural values so that they are not unnecessarily exposed to impact or disturbances. Just as before, the programme will be continuously adapted to the knowledge that is gradually accumulated on the site. All important changes will be reported to the authorities and other concerned parties. The investigations that have been conducted (as of August 2004) and their results can be summarized in the following points: The surface characterization

Forsmark site investigation. Programme for further investigations of geosphere and biosphere

International Nuclear Information System (INIS)

2005-01-01

Since the beginning of 2002, SKB (the Swedish Nuclear Fuel and Waste Management Co) has been conducting a site investigation in Forsmark in the municipality of Oesthammar for siting of the deep repository for spent nuclear fuel. An equivalent investigation is also being conducted at Simpevarp and Laxemar in Oskarshamn Municipality. SKB's goal is to submit an application under the Environmental Code and the Nuclear Activities Act for siting of the deep repository at one of these sites by the end of 2008/beginning of 2009. When the application is submitted, everything of importance for the deep repository's safety, constructability and environmental impact shall have been investigated and analyzed. The investigations shall also provide data as a basis for selecting a site and configuring the facility to suit conditions on the site.SKB submitted a programme for the initial site investigation in Forsmark at the end of 2001. The investigations described there have now been completed. This report describes the programme that has now been prepared for the remainder of the site investigation. The points of departure are the general goals for the Deep Repository Project during the site investigation phase, the data needed for evaluation of the site, plus experience and results from the work to date. The programme has been prepared with the support of investigation data as of August 2004. The investigations described here will, as before, be conducted with great consideration given to residents, property owners and natural and cultural values so that they are not unnecessarily exposed to impact or disturbances. Just as before, the programme will be continuously adapted to the knowledge that is gradually accumulated on the site. All important changes will be reported to the authorities and other concerned parties. The investigations that have been conducted (as of August 2004) and their results can be summarized in the following points: The surface characterization of the

Users Manual for the FEHMN application

International Nuclear Information System (INIS)

Zyvoloski, G.A.; Robinson, B.A.; Dash, Z.V.; Trease, L.L.

1996-01-01

The user's manual documents the use of the Yucca Mountain Site Characterization Projects Finite element heat and mass transfer code (FEHMN) application. The manual covers: Program considerations, data files, input data, output, system interface, and examples

Radiological control manual. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Kloepping, R.

1996-05-01

This Lawrence Berkeley National Laboratory Radiological Control Manual (LBNL RCM) has been prepared to provide guidance for site-specific additions, supplements and interpretation of the DOE Radiological Control Manual. The guidance provided in this manual is one methodology to implement the requirements given in Title 10 Code of Federal Regulations Part 835 (10 CFR 835) and the DOE Radiological Control Manual. Information given in this manual is also intended to provide demonstration of compliance to specific requirements in 10 CFR 835. The LBNL RCM (Publication 3113) and LBNL Health and Safety Manual Publication-3000 form the technical basis for the LBNL RPP and will be revised as necessary to ensure that current requirements from Rules and Orders are represented. The LBNL RCM will form the standard for excellence in the implementation of the LBNL RPP.

Radiological control manual. Revision 1

International Nuclear Information System (INIS)

Kloepping, R.

1996-05-01

This Lawrence Berkeley National Laboratory Radiological Control Manual (LBNL RCM) has been prepared to provide guidance for site-specific additions, supplements and interpretation of the DOE Radiological Control Manual. The guidance provided in this manual is one methodology to implement the requirements given in Title 10 Code of Federal Regulations Part 835 (10 CFR 835) and the DOE Radiological Control Manual. Information given in this manual is also intended to provide demonstration of compliance to specific requirements in 10 CFR 835. The LBNL RCM (Publication 3113) and LBNL Health and Safety Manual Publication-3000 form the technical basis for the LBNL RPP and will be revised as necessary to ensure that current requirements from Rules and Orders are represented. The LBNL RCM will form the standard for excellence in the implementation of the LBNL RPP

Manual for implementing residual radioactivity guidelines

International Nuclear Information System (INIS)

Gilbert, T.L.; Eckerman, K.F.; Hansen, W.R.; Healy, J.W.; Kennedy, W.E.; Napier, B.A.; Solday, J.K.

1986-01-01

The US Department of Energy (DOE) has recently issued guidelines for residual radioactivity at Formerly Utilized Sites Remedial Action Program (FUSRAP) and remote Surplus Facilities Management Program (SFMP) sites. A manual for implementing these guidelines has been prepared jointly by four DOE laboratories (ANL, LANL, ORNL, and PNL) and is being issued as a supplement to the guidelines. The manual presents procedures and tables for deriving site-specific guidelines for levels of residual radionuclide concentrations in soil that must not be exceeded if a site is to be released for unrestricted use. Guidance for implementing DOE ALARA policy for remedial actions is also included. The concentration factor method is used in the pathway analysis for deriving soil guidelines. The analysis has been structured in a manner that explicitly identifies all of the factors involved. Tables are provided for dose-conversion factors and pathway factors from which environmental transport factors for each radionuclide and pathway may be calculated. The scenarios used for deriving the environmental transport factors and dose conversion factors, and the manner in which the information provided in the manual is used to derive site-specific soil guidelines will be presented

Investigation of piloting aids for manual control of hypersonic maneuvers

Science.gov (United States)

Raney, David L.; Phillips, Michael R.; Person, Lee H., Jr.

1995-01-01

An investigation of piloting aids designed to provide precise maneuver control for an air-breathing hypersonic vehicle is described. Stringent constraints and nonintuitive high-speed flight effects associated with maneuvering in the hypersonic regime raise the question of whether manual control of such a vehicle should even be considered. The objectives of this research were to determine the extent of manual control that is desirable for a vehicle maneuvering in this regime and to identify the form of aids that must be supplied to the pilot to make such control feasible. A piloted real-time motion-based simulation of a hypersonic vehicle concept was used for this study, and the investigation focused on a single representative cruise turn maneuver. Piloting aids, which consisted of an auto throttle, throttle director, autopilot, flight director, and two head-up display configurations, were developed and evaluated. Two longitudinal control response types consisting of a rate-command/attitude-hold system and a load factor-rate/load-factor-hold system were also compared. The complete set of piloting aids, which consisted of the autothrottle, throttle director, and flight director, improved the average Cooper-Harper flying qualities ratings from 8 to 2.6, even though identical inner-loop stability and control augmentation was provided in all cases. The flight director was determined to be the most critical of these aids, and the cruise turn maneuver was unachievable to adequate performance specifications in the absence of this flight director.

Execution programme for the initial site investigations at Forsmark

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-05-01

In the feasibility studies that were completed in 2001, eight sites were identified as potentially suitable for hosting a repository. All the identified sites meet the safety requirements with respect to bedrock conditions that could be checked at that time. The feasibility studies have revealed good potential when it comes to the technical and environmental aspects as well. Based on an integrated evaluation SKB proposed to start site investigations with test drillings at three sites; Forsmark, Simpevarp and Tierp. Site investigations have started at Forsmark and Simpevarp. The municipal council of Tierp voted no to a site investigation in April 2002. The site investigations are divided into two main phases; initial and complete investigations. Initial site investigations are performed to identify the site within a specified area that is deemed to be most suitable for a deep repository and to determine whether the feasibility study's judgement of the suitability of the area holds up in the light of borehole data from repository depth. The initial site investigations are expected to take 1.5-2 years. If the assessment shows that the site has good potential to host a repository, complete site investigations will follow for an expected duration of 3.5-4 years. The purpose of the complete site investigations is to gather all information required to select one of the sites as the main alternative and to apply for a permit for construction of the deep repository at that site. A general programme in which the results from feasibility studies are summarized, the candidate sites presented and the framework of programme for the site investigation phase presented has been published. The general programme, and main references to the programme, specifies which data are required in order to design the repository and carry out a safety assessment, how the investigations should be carried out in order to provide these data, criteria with which the site must comply, as well as

Execution programme for the initial site investigations at Forsmark

International Nuclear Information System (INIS)

2002-05-01

In the feasibility studies that were completed in 2001, eight sites were identified as potentially suitable for hosting a repository. All the identified sites meet the safety requirements with respect to bedrock conditions that could be checked at that time. The feasibility studies have revealed good potential when it comes to the technical and environmental aspects as well. Based on an integrated evaluation SKB proposed to start site investigations with test drillings at three sites; Forsmark, Simpevarp and Tierp. Site investigations have started at Forsmark and Simpevarp. The municipal council of Tierp voted no to a site investigation in April 2002. The site investigations are divided into two main phases; initial and complete investigations. Initial site investigations are performed to identify the site within a specified area that is deemed to be most suitable for a deep repository and to determine whether the feasibility study's judgement of the suitability of the area holds up in the light of borehole data from repository depth. The initial site investigations are expected to take 1.5-2 years. If the assessment shows that the site has good potential to host a repository, complete site investigations will follow for an expected duration of 3.5-4 years. The purpose of the complete site investigations is to gather all information required to select one of the sites as the main alternative and to apply for a permit for construction of the deep repository at that site. A general programme in which the results from feasibility studies are summarized, the candidate sites presented and the framework of programme for the site investigation phase presented has been published. The general programme, and main references to the programme, specifies which data are required in order to design the repository and carry out a safety assessment, how the investigations should be carried out in order to provide these data, criteria with which the site must comply, as well as

Salmon Site Remedial Investigation Report

International Nuclear Information System (INIS)

1999-01-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Utilization of multimode Love wave dispersion curve inversion for geotechnical site investigation

International Nuclear Information System (INIS)

Hamimu, La; Nawawi, Mohd; Safani, Jamhir

2011-01-01

Inversion codes based on a modified genetic algorithm (GA) have been developed to invert multimode Love wave dispersion curves. The multimode Love wave dispersion curves were synthesized from the profile representing shear-wave velocity reversal using a full SH (shear horizontal) waveform. In this study, we used a frequency–slowness transform to extract the dispersion curve from the full SH waveform. Dispersion curves overlain in dispersion images were picked manually. These curves were then inverted using the modified GA. To assess the accuracy of the inversion results, differences between the true and inverted shear-wave velocity profile were quantified in terms of shear-wave velocity and thickness errors, E S and E H . Our numerical modeling showed that the inversion of multimode dispersion curves can significantly provide the better assessment of a shear-wave velocity structure, especially with a velocity reversal profile at typical geotechnical site investigations. This approach has been applied on field data acquired at a site in Niigata prefecture, Japan. In these field data, our inversion results show good agreement between the calculated and experimental dispersion curves and accurately detect low velocity layer targets

Radiological control technician: Training program management manual

International Nuclear Information System (INIS)

1992-10-01

This manual defines and describes the DOE Radiological Control Technician Core Training Program qualification and training process, material development requirements, standards and policies, and administration. The manual applies to Radiological Control Technician Training Programs at all DOE contractor sites

Sandia SWiFT Wind Turbine Manual.

Energy Technology Data Exchange (ETDEWEB)

White, Jonathan; LeBlanc, Bruce Philip; Berg, Jonathan Charles; Bryant, Joshua; Johnson, Wesley D.; Paquette, Joshua

2016-01-01

The Scaled Wind Farm Technology (SWiFT) facility, operated by Sandia National Laboratories for the U.S. Department of Energy's Wind and Water Power Program, is a wind energy research site with multiple wind turbines scaled for the experimental study of wake dynamics, advanced rotor development, turbine control, and advanced sensing for production-scale wind farms. The SWiFT site currently includes three variable-speed, pitch-regulated, three-bladed wind turbines. The six volumes of this manual provide a detailed description of the SWiFT wind turbines, including their operation and user interfaces, electrical and mechanical systems, assembly and commissioning procedures, and safety systems. Further dissemination only as authorized to U.S. Government agencies and their contractors; other requests shall be approved by the originating facility or higher DOE programmatic authority. 111 UNCLASSIFIED UNLIMITED RELEASE Sandia SWiFT Wind Turbine Manual (SAND2016-0746 ) approved by: Department Manager SWiFT Site Lead Dave Minster (6121) Date Jonathan White (6121) Date SWiFT Site Supervisor Dave Mitchell (6121) Date Note: Document revision logs are found after the title page of each volume of this manual. iv

Summary report of the experiences from TVO's site investigations

International Nuclear Information System (INIS)

Oehberg, A.; Saksa, P.; Ahokas, H.; Ruotsalainen, P.; Snellman, M.

1994-05-01

Teollisuuden Voima Oy (TVO) has completed preliminary site investigations at five sites in Finland. At the end of 1992 TVO presented the final report to the authorities. The preliminary site investigation phase 1986-1992 was conducted according to the investigation programme compiled by TVO. The aim of this report was to compile a report on experiences from TVOs site investigations. The main interest was focused on investigation strategies and the most important investigation methods for the conceptual modelling. The objective of the preliminary site investigations was to obtain data on the bedrock properties in order to evaluate the areas. The programme was divided into four stages, each stage having its own sub-objective. The site-specific investigation programme for each site included a large common part and a small site-specific part. The strategies (objectives) and experiences from different disciplines, geology, hydrogeochemistry, geophysics and geohydrology, are presented in the report. The conceptual modelling work procedure including both bedrock and groundwater modelling is described briefly using the Olkiluoto site as an example. Each of the other areas has undergone similar phases of work. The uncertainties associated with conceptual modelling are also discussed. The usefulness of the investigation strategy and the investigation methods for conceptual modelling is discussed in the report. Some new equipment, methods or enhancements that have not yet been used in TVOs site investigations have become new tools in site characterisation and are briefly presented in the report. 52 refs, 35 figs, 1 tab

Hydrogeological Site Descriptive Model - a strategy for its development during Site Investigations

Energy Technology Data Exchange (ETDEWEB)

Rhen, Ingvar [SWECO VIAK AB, Goeteborg (Sweden); Follin, Sven [SF GeoLogic AB, Stockholm (Sweden); Hermanson, Jan [Golder Associates, Stockholm (Sweden)

2003-04-01

The report is to present a strategy for the development of the Site Descriptive Hydrogeological Model within the SKB Site Investigation Programme. The report, and similar reports from the Geology, Rock Mechanics, Thermal properties, Hydrogeochemistry, Transport Properties and Surface Ecosystem disciplines are intended to guide SKB Site Descriptive Modelling but also to provide the authorities with an overview of how the modelling should be performed. Thus the objectives of this report are to: provide guidelines for the modelling of different sites resulting in consistent handling of modelling issues during the Site Investigations, provide a structure for the modelling sequence that is suitable for the establishment of a Site Descriptive model and provide some necessary details that should be considered in a Site Descriptive model.

Hydrogeological Site Descriptive Model - a strategy for its development during Site Investigations

International Nuclear Information System (INIS)

Rhen, Ingvar; Follin, Sven; Hermanson, Jan

2003-04-01

The report is to present a strategy for the development of the Site Descriptive Hydrogeological Model within the SKB Site Investigation Programme. The report, and similar reports from the Geology, Rock Mechanics, Thermal properties, Hydrogeochemistry, Transport Properties and Surface Ecosystem disciplines are intended to guide SKB Site Descriptive Modelling but also to provide the authorities with an overview of how the modelling should be performed. Thus the objectives of this report are to: provide guidelines for the modelling of different sites resulting in consistent handling of modelling issues during the Site Investigations, provide a structure for the modelling sequence that is suitable for the establishment of a Site Descriptive model and provide some necessary details that should be considered in a Site Descriptive model

Hanford Site Solid Waste Acceptance Criteria

Energy Technology Data Exchange (ETDEWEB)

1993-11-17

This manual defines the Hanford Site radioactive, hazardous, and sanitary solid waste acceptance criteria. Criteria in the manual represent a guide for meeting state and federal regulations; DOE Orders; Hanford Site requirements; and other rules, regulations, guidelines, and standards as they apply to acceptance of radioactive and hazardous solid waste at the Hanford Site. It is not the intent of this manual to be all inclusive of the regulations; rather, it is intended that the manual provide the waste generator with only the requirements that waste must meet in order to be accepted at Hanford Site TSD facilities.

Hanford Site Solid Waste Acceptance Criteria

International Nuclear Information System (INIS)

1993-01-01

This manual defines the Hanford Site radioactive, hazardous, and sanitary solid waste acceptance criteria. Criteria in the manual represent a guide for meeting state and federal regulations; DOE Orders; Hanford Site requirements; and other rules, regulations, guidelines, and standards as they apply to acceptance of radioactive and hazardous solid waste at the Hanford Site. It is not the intent of this manual to be all inclusive of the regulations; rather, it is intended that the manual provide the waste generator with only the requirements that waste must meet in order to be accepted at Hanford Site TSD facilities

Execution programme for the initial site investigations at Simpevarp

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-10-01

In the feasibility studies that were completed in 2001, eight sites were identified as potentially suitable for hosting a repository. All the identified sites meet the safety requirements with respect to bedrock conditions that could be checked at that time. The feasibility studies have revealed good potential when it comes to the technical and environmental aspects as well. Based on an integrated evaluation SKB proposed to start site investigations with test drillings at three sites; Simpevarp, Forsmark, and Tierp north. The site investigations have started at Simpevarp and Forsmark. The municipal council of Tierp rejected a site investigation in April 2002. The site investigations are divided into two main phases; initial and complete investigations. Initial Site Investigation is performed to identify the site within a specified area that is deemed to be most suitable for a deep repository and to determine whether the feasibility study's judgement of the suitability of the area holds up in the light of borehole data from repository depth. The Initial Site Investigation is expected to take about 3 years. If the assessment shows that the site has good potential to host a repository, Complete Site Investigation will follow for an expected duration of another 3 years. The purpose of the Complete Site Investigation is to gather all information required to select one of the sites as the main alternative and to apply for a permit for construction of the deep repository at that site. The site-specific programme gives an overview of the whole site investigation phase as well as a detailed description of the initial stage. The results of the initial investigations will determine whether Simpevarp is appropriate for further investigation, i.e. the Complete Site Investigation. This document summarizes the investigations that will be carried out at Simpevarp during the Initial Site Investigations. The document is a working document, which will be successively updated as

Execution programme for the initial site investigations at Simpevarp

International Nuclear Information System (INIS)

2002-10-01

In the feasibility studies that were completed in 2001, eight sites were identified as potentially suitable for hosting a repository. All the identified sites meet the safety requirements with respect to bedrock conditions that could be checked at that time. The feasibility studies have revealed good potential when it comes to the technical and environmental aspects as well. Based on an integrated evaluation SKB proposed to start site investigations with test drillings at three sites; Simpevarp, Forsmark, and Tierp north. The site investigations have started at Simpevarp and Forsmark. The municipal council of Tierp rejected a site investigation in April 2002. The site investigations are divided into two main phases; initial and complete investigations. Initial Site Investigation is performed to identify the site within a specified area that is deemed to be most suitable for a deep repository and to determine whether the feasibility study's judgement of the suitability of the area holds up in the light of borehole data from repository depth. The Initial Site Investigation is expected to take about 3 years. If the assessment shows that the site has good potential to host a repository, Complete Site Investigation will follow for an expected duration of another 3 years. The purpose of the Complete Site Investigation is to gather all information required to select one of the sites as the main alternative and to apply for a permit for construction of the deep repository at that site. The site-specific programme gives an overview of the whole site investigation phase as well as a detailed description of the initial stage. The results of the initial investigations will determine whether Simpevarp is appropriate for further investigation, i.e. the Complete Site Investigation. This document summarizes the investigations that will be carried out at Simpevarp during the Initial Site Investigations. The document is a working document, which will be successively updated as

Revegetation manual for the environmental restoration contractor

International Nuclear Information System (INIS)

McLendon, T.; Redente, E.F.

1997-02-01

The purpose of this manual is to provide guidance and general guidelines for the revegetation of remediation waste sites and other disturbed areas on the Hanford Site. Specific revegetation plans will be developed using guidance from this manual. Locations, resources, and funding will dictate the specific revegetation design at each disturbed area. Disturbances have occurred to some of the ecological communities of the Hanford Site. Many of these disturbances are the result of operations of the Hanford Site, including Comprehensive Environmental Response, Compensation, and Liability Act of 1980 waste sites on small portions of the Hanford Site. There were, however, extensive disturbances to the native vegetation prior to operations of the facility. These resulted from cultivation, grazing, fire, and the introduction of exotics. Revegetation planning must take into account these early disturbances, as well as the later ones

Revegetation manual for the environmental restoration contractor

Energy Technology Data Exchange (ETDEWEB)

McLendon, T.; Redente, E.F.

1997-02-01

The purpose of this manual is to provide guidance and general guidelines for the revegetation of remediation waste sites and other disturbed areas on the Hanford Site. Specific revegetation plans will be developed using guidance from this manual. Locations, resources, and funding will dictate the specific revegetation design at each disturbed area. Disturbances have occurred to some of the ecological communities of the Hanford Site. Many of these disturbances are the result of operations of the Hanford Site, including Comprehensive Environmental Response, Compensation, and Liability Act of 1980 waste sites on small portions of the Hanford Site. There were, however, extensive disturbances to the native vegetation prior to operations of the facility. These resulted from cultivation, grazing, fire, and the introduction of exotics. Revegetation planning must take into account these early disturbances, as well as the later ones.

Hanford Waste Vitrification Plant technical manual

Energy Technology Data Exchange (ETDEWEB)

Larson, D.E. [ed.; Watrous, R.A.; Kruger, O.L. [and others

1996-03-01

A key element of the Hanford waste management strategy is the construction of a new facility, the Hanford Waste Vitrification Plant (HWVP), to vitrify existing and future liquid high-level waste produced by defense activities at the Hanford Site. The HWVP mission is to vitrify pretreated waste in borosilicate glass, cast the glass into stainless steel canisters, and store the canisters at the Hanford Site until they are shipped to a federal geological repository. The HWVP Technical Manual (Manual) documents the technical bases of the current HWVP process and provides a physical description of the related equipment and the plant. The immediate purpose of the document is to provide the technical bases for preparation of project baseline documents that will be used to direct the Title 1 and Title 2 design by the A/E, Fluor. The content of the Manual is organized in the following manner. Chapter 1.0 contains the background and context within which the HWVP was designed. Chapter 2.0 describes the site, plant, equipment and supporting services and provides the context for application of the process information in the Manual. Chapter 3.0 provides plant feed and product requirements, which are primary process bases for plant operation. Chapter 4.0 summarizes the technology for each plant process. Chapter 5.0 describes the engineering principles for designing major types of HWVP equipment. Chapter 6.0 describes the general safety aspects of the plant and process to assist in safe and prudent facility operation. Chapter 7.0 includes a description of the waste form qualification program and data. Chapter 8.0 indicates the current status of quality assurance requirements for the Manual. The Appendices provide data that are too extensive to be placed in the main text, such as extensive tables and sets of figures. The Manual is a revision of the 1987 version.

Hanford Waste Vitrification Plant technical manual

International Nuclear Information System (INIS)

Larson, D.E.; Watrous, R.A.; Kruger, O.L.

1996-03-01

A key element of the Hanford waste management strategy is the construction of a new facility, the Hanford Waste Vitrification Plant (HWVP), to vitrify existing and future liquid high-level waste produced by defense activities at the Hanford Site. The HWVP mission is to vitrify pretreated waste in borosilicate glass, cast the glass into stainless steel canisters, and store the canisters at the Hanford Site until they are shipped to a federal geological repository. The HWVP Technical Manual (Manual) documents the technical bases of the current HWVP process and provides a physical description of the related equipment and the plant. The immediate purpose of the document is to provide the technical bases for preparation of project baseline documents that will be used to direct the Title 1 and Title 2 design by the A/E, Fluor. The content of the Manual is organized in the following manner. Chapter 1.0 contains the background and context within which the HWVP was designed. Chapter 2.0 describes the site, plant, equipment and supporting services and provides the context for application of the process information in the Manual. Chapter 3.0 provides plant feed and product requirements, which are primary process bases for plant operation. Chapter 4.0 summarizes the technology for each plant process. Chapter 5.0 describes the engineering principles for designing major types of HWVP equipment. Chapter 6.0 describes the general safety aspects of the plant and process to assist in safe and prudent facility operation. Chapter 7.0 includes a description of the waste form qualification program and data. Chapter 8.0 indicates the current status of quality assurance requirements for the Manual. The Appendices provide data that are too extensive to be placed in the main text, such as extensive tables and sets of figures. The Manual is a revision of the 1987 version

Summary report of the experiences from TVO's site investigations

International Nuclear Information System (INIS)

Oehberg, A.; Saksa, P.; Ahokas, H.; Ruotsalainen, P.; Snellman, M.

1994-09-01

In 1992 Teollisuuden Voima Oy (TVO) completed preliminary site investigations for radioactive waste disposal at five sites in Finland. The aim of this report was the compilation of the experiences from TVO's site investigations. The main interest was focused on investigation strategies and the most important investigation methods for the conceptual modelling. The objective of the preliminary site investigations was to obtain data on the bedrock properties in order to evaluate the areas. The programme was divided into four stages, each stage having its own subobjective. The site-specific investigation programme for each site included a large common part and a small site-specific part. The strategies (objectives) and experiences from different disciplines, geology, hydrogeochemistry, geophysics and geohydrology, are presented in the report. The conceptual modelling work procedure including both bedrock and groundwater modelling is described briefly using the Olkiluoto site as an example. Each of the other areas has undergone similar phases of work. (52 refs., 45 figs., 5 tabs.)

Site description of Forsmark at completion of the site investigation phase. SDM-Site Forsmark

Energy Technology Data Exchange (ETDEWEB)

2008-12-15

The Swedish Nuclear Fuel and Waste Management Co., SKB, has undertaken site characterisation in two different areas, Forsmark and Laxemar-Simpevarp, in order to identify a suitable location for a geological repository of spent nuclear fuel according to the KBS-3 method. The site investigations have been conducted in campaigns, punctuated by data freezes. After each data freeze, the site data have been analysed and modelling has been carried out with the overall purpose to develop a site descriptive model (SDM). The site descriptive model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It is also essential for safety assessment, since the model is the only source for site-specific input. Another important use of the site descriptive model is in the environmental impact assessment. An SDM is an integrated model for geology, thermal properties, rock mechanics, hydrogeology, hydrogeochemistry, bedrock transport properties and a description of the surface system. The site descriptive model compiled in the current report, SDM-Site, presents an integrated understanding of the Forsmark area at the completion of the surface-based investigations, which were conducted at Forsmark during the period 2002 to 2007. It also provides a summary of the abundant underlying data and the discipline-specific models that support the site understanding. The description relies heavily on background reports that address, in particular, details in data analyses and modelling in the different disciplines. The Forsmark area is located in northern Uppland within the municipality of Oesthammar, about 120 km north of Stockholm. The candidate area for site investigation is located along the shoreline of Oeregrundsgrepen, within the north-western part of a major tectonic lens that formed between 1.87 and 1.85 billion years ago during the Svecokarelian orogeny. The candidate area is approximately 6 km long and 2 km wide. The

Site description of Laxemar at completion of the site investigation phase. SDM-Site Laxemar

Energy Technology Data Exchange (ETDEWEB)

2009-12-15

The Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken site characterisation in two different areas, Forsmark and Laxemar-Simpevarp, in order to identify a suitable location for a geological repository of spent nuclear fuel according to the KBS-3 method. The site investigations have been conducted in campaigns, punctuated by data freezes. After each data freeze, the site data have been analysed and modelling has been carried out with the overall purpose to develop a site descriptive model (SDM). The site descriptive model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It is also essential for safety assessment, since the SDM is the only source for site-specific input. Another important use of the site descriptive model is in the environmental impact assessment. An SDM is an integrated model of geology, thermal properties, rock mechanics, hydrogeology, hydrogeochemistry, bedrock transport properties and a description of the surface system. The site descriptive model compiled in the current report, SDM-Site Laxemar, presents an integrated understanding of the Laxemar-Simpevarp area (with special emphasis on the Laxemar subarea) at the completion of the surface-based investigations, which were conducted during the period 2002 to 2007. A summary is also provided of the abundant underlying data and the discipline specific models that support the site understanding. The description relies heavily on background reports that address, in particular, details of the data analyses and modelling of the different disciplines. The Laxemar-Simpevarp area is located in the province of Smaaland within the municipality of Oskarshamn, about 230 km south of Stockholm. The candidate area for site investigation is located along the shoreline of the strait of Kalmarsund, within a 1.8 billion year old suite of well preserved bedrock belonging to the Transscandinavian Igneous Belt formed during

Site description of Laxemar at completion of the site investigation phase. SDM-Site Laxemar

International Nuclear Information System (INIS)

2009-12-01

The Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken site characterisation in two different areas, Forsmark and Laxemar-Simpevarp, in order to identify a suitable location for a geological repository of spent nuclear fuel according to the KBS-3 method. The site investigations have been conducted in campaigns, punctuated by data freezes. After each data freeze, the site data have been analysed and modelling has been carried out with the overall purpose to develop a site descriptive model (SDM). The site descriptive model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It is also essential for safety assessment, since the SDM is the only source for site-specific input. Another important use of the site descriptive model is in the environmental impact assessment. An SDM is an integrated model of geology, thermal properties, rock mechanics, hydrogeology, hydrogeochemistry, bedrock transport properties and a description of the surface system. The site descriptive model compiled in the current report, SDM-Site Laxemar, presents an integrated understanding of the Laxemar-Simpevarp area (with special emphasis on the Laxemar subarea) at the completion of the surface-based investigations, which were conducted during the period 2002 to 2007. A summary is also provided of the abundant underlying data and the discipline specific models that support the site understanding. The description relies heavily on background reports that address, in particular, details of the data analyses and modelling of the different disciplines. The Laxemar-Simpevarp area is located in the province of Smaaland within the municipality of Oskarshamn, about 230 km south of Stockholm. The candidate area for site investigation is located along the shoreline of the strait of Kalmarsund, within a 1.8 billion year old suite of well preserved bedrock belonging to the Transscandinavian Igneous Belt formed during

Site description of Forsmark at completion of the site investigation phase. SDM-Site Forsmark

International Nuclear Information System (INIS)

2008-12-01

The Swedish Nuclear Fuel and Waste Management Co., SKB, has undertaken site characterisation in two different areas, Forsmark and Laxemar-Simpevarp, in order to identify a suitable location for a geological repository of spent nuclear fuel according to the KBS-3 method. The site investigations have been conducted in campaigns, punctuated by data freezes. After each data freeze, the site data have been analysed and modelling has been carried out with the overall purpose to develop a site descriptive model (SDM). The site descriptive model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It is also essential for safety assessment, since the model is the only source for site-specific input. Another important use of the site descriptive model is in the environmental impact assessment. An SDM is an integrated model for geology, thermal properties, rock mechanics, hydrogeology, hydrogeochemistry, bedrock transport properties and a description of the surface system. The site descriptive model compiled in the current report, SDM-Site, presents an integrated understanding of the Forsmark area at the completion of the surface-based investigations, which were conducted at Forsmark during the period 2002 to 2007. It also provides a summary of the abundant underlying data and the discipline-specific models that support the site understanding. The description relies heavily on background reports that address, in particular, details in data analyses and modelling in the different disciplines. The Forsmark area is located in northern Uppland within the municipality of Oesthammar, about 120 km north of Stockholm. The candidate area for site investigation is located along the shoreline of Oeregrundsgrepen, within the north-western part of a major tectonic lens that formed between 1.87 and 1.85 billion years ago during the Svecokarelian orogeny. The candidate area is approximately 6 km long and 2 km wide. The

Radiation protection technician job task analysis manual

International Nuclear Information System (INIS)

1990-03-01

This manual was developed to assist all DOE contractors in the design and conduct of job task analysis (JTA) for the radiation protection technician. Experience throughout the nuclear industry and the DOE system has indicated that the quality and efficiency in conducting a JTA at most sites is greatly enhanced by using a generic task list for the position, and clearly written guidelines on the JTA process. This manual is designed to provide this information for personnel to use in developing and conducting site-specific JTAs. (VC)

Radiological Control Manual. Revision 0, January 1993

Energy Technology Data Exchange (ETDEWEB)

1993-04-01

This manual has been prepared by Lawrence Berkeley Laboratory to provide guidance for site-specific additions, supplements, and clarifications to the DOE Radiological Control Manual. The guidance provided in this manual is based on the requirements given in Title 10 Code of Federal Regulations Part 835, Radiation Protection for Occupational Workers, DOE Order 5480.11, Radiation Protection for Occupational Workers, and the DOE Radiological Control Manual. The topics covered are (1) excellence in radiological control, (2) radiological standards, (3) conduct of radiological work, (4) radioactive materials, (5) radiological health support operations, (6) training and qualification, and (7) radiological records.

When is there sufficient information from the Site Investigations?

International Nuclear Information System (INIS)

Andersson, Johan; Munier, Raymond; Stroem, Anders; Soederbaeck, Bjoern; Almen, Karl-Erik; Olsson, Lars

2004-04-01

SKB has started site investigations for a deep repository for spent nuclear fuel at two different sites in Sweden. The investigations should provide necessary information for a licence application aimed at starting underground exploration. The investigations and analyses of them are supposed to provide the broad knowledge base that is required to achieve the overall goals of the site investigation phase. The knowledge will be utilized to evaluate the suitability of investigated sites for the deep repository and must be comprehensive enough to: Show whether the selected site satisfies requirements on safety and technical aspects. Serve as a basis for adaptation of the deep repository to the characteristics of the site with an acceptable impact on society and the environment. Permit comparisons with other investigated sites. Furthermore, the investigations are discontinued when the reliability of the site description has reached such a level that the body of data for safety assessment and design is sufficient, or until the body of data shows that the rock does not satisfy the requirements. These objectives are valid, but do not provide sufficient and concrete guidance. For this reason SKB has conducted this project which should acquire concrete guidance on how to judge when the surface based Site Investigation Phase does not need to continue. After a general assessment of the problem, the following specific objectives of the current work were identified: Demonstrate concretely how the assessed uncertainties in a Site Description based on a specific level of investigations, together with expected feedback from Safety Assessment and Engineering, can be used to decide whether the site investigations are sufficient - or need to continue. This demonstration will be based on a practical application of relevant aspects of decision analysis tools. Highlight and make concrete the type of feedback to be expected from Safety Assessment and Engineering and show how this feedback

When is there sufficient information from the Site Investigations?

Energy Technology Data Exchange (ETDEWEB)

Andersson, Johan [JA Streamflow AB, Aelvsjoe (Sweden); Munier, Raymond; Stroem, Anders; Soederbaeck, Bjoern [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Almen, Karl-Erik [KEA Geo-konsult (Sweden); Olsson, Lars [Geostatistik AB, Tumba (Sweden)

2004-04-01

SKB has started site investigations for a deep repository for spent nuclear fuel at two different sites in Sweden. The investigations should provide necessary information for a licence application aimed at starting underground exploration. The investigations and analyses of them are supposed to provide the broad knowledge base that is required to achieve the overall goals of the site investigation phase. The knowledge will be utilized to evaluate the suitability of investigated sites for the deep repository and must be comprehensive enough to: Show whether the selected site satisfies requirements on safety and technical aspects. Serve as a basis for adaptation of the deep repository to the characteristics of the site with an acceptable impact on society and the environment. Permit comparisons with other investigated sites. Furthermore, the investigations are discontinued when the reliability of the site description has reached such a level that the body of data for safety assessment and design is sufficient, or until the body of data shows that the rock does not satisfy the requirements. These objectives are valid, but do not provide sufficient and concrete guidance. For this reason SKB has conducted this project which should acquire concrete guidance on how to judge when the surface based Site Investigation Phase does not need to continue. After a general assessment of the problem, the following specific objectives of the current work were identified: Demonstrate concretely how the assessed uncertainties in a Site Description based on a specific level of investigations, together with expected feedback from Safety Assessment and Engineering, can be used to decide whether the site investigations are sufficient - or need to continue. This demonstration will be based on a practical application of relevant aspects of decision analysis tools. Highlight and make concrete the type of feedback to be expected from Safety Assessment and Engineering and show how this feedback

Oskarshamn site investigation. Programme for further investigations of bedrock, soil, water and environment in Laxemar subarea

International Nuclear Information System (INIS)

2006-03-01

SKB (the Swedish Nuclear Fuel and Waste Management Co), has been conducting a site investigation at Simpevarp and Laxemar in Oskarshamn for siting of a final repository for spent nuclear fuel. An equivalent investigation is being conducted in Forsmark in Ohmmeter's. The initial part of the site investigations had been completed for the both of the subareas Simpevarp and Laxemar in the autumn of 2004. Based on the results of these investigations, SKB preliminarily prioritized the Laxemar subarea for further investigations. A programme was presented for the first stage of the complete site investigation in the Laxemar subarea, along with the main features of the remainder of the site investigation. The programme included investigations up until the summer of 2005 and was particularly aimed at obtaining answers to several vital questions so that the subsequent investigations could be focused on the rock areas judged to be most suitable for a final repository. These investigations have now been completed. This report presents the programme for the remainder of the site investigation. The points of departure are the general goals for the Deep Repository Project during the site investigation phase, analyses and evaluations of data from completed investigations, and the needs for additional data to be able to evaluate the site as a siting alternative for the final repository. The account mainly covers the investigations on the site. All other work - analyses, site descriptive modelling, facility design, safety assessments and studies and assessments of consequences for the environment, human health and society - are only mentioned to the extent necessary in order to place the investigations in their context. The direction of the site investigation in Oskarshamn and the investigation programme presented in this report is based on SKB's preliminary decision to prioritize the Laxemar subarea for further investigations. A final decision on the direction of the site

Alternative approaches to improve site investigations

International Nuclear Information System (INIS)

Beach, R.B.; Silka, L.R.

1992-01-01

Common complaints about standard investigations at hazardous waste sites include high costs and long time frames. Investigations at military bases as part of the installation restoration program or base closures suffer additionally from nonuniformity of approach and results and redundancy of work effort conducted by multiple environmental contractors. The problems of high costs and long time frames can be minimized by the consistent use of alternative sampling methods (such as soil gas surveys) and the utilization of analytical screening procedures at both on-site and off-site laboratories. Acceptable data quality is maintained by several procedures. Incorporation of quality control measures (10 % frequency), such as matrix spikes and duplicates, into the alternative analytical techniques allows assessment of the data quality relative to predetermined data quality objectives (DQOs). Confirmation of the screening results (10% frequency) using standard US EPA methods, such as the contract laboratory program (CLP) statement of work (SOW), allows an additional evaluation of the data accuracy. Depending on the investigative objectives, knowledge based computer systems (expert systems,) could be used to improve uniformity of site evaluations. Several case histories will be presented demonstrating how soil gas surveys, screening analyses and standard analyses can be utilized to give increased site information in a reduced time frame and at a cost savings of 30 to 40%. One case history illustrates a screening technique developed by the author for polynuclear aromatics (semi-volatile organic compounds) that can be conducted at a cost savings of 90% relative to a standard US EPA method. A comparison of the phased investigative approach to one using an integrated field team is presented for fuel spill or UST areas

Data collection system. Volume 1, Overview and operators manual; Volume 2, Maintenance manual; Appendices

Energy Technology Data Exchange (ETDEWEB)

Caudell, R.B.; Bauder, M.E.; Boyer, W.B.; French, R.E.; Isidoro, R.J.; Kaestner, P.C.; Perkins, W.G.

1993-09-01

Sandia National Laboratories (SNL) Instrumentation Development Department was tasked by the Defense Nuclear Agency (DNA) to record data on Tektronix RTD720 Digitizers on the HUNTERS TROPHY field test conducted at the Nevada Test Site (NTS) on September 18, 1992. This report contains a overview and description of the computer hardware and software that was used to acquire, reduce, and display the data. The document is divided into two volumes: an overview and operators manual (Volume 1) and a maintenance manual (Volume 2).

AN EXPLORATORY STUDY INVESTIGATING THE EFFECTS OF A TREATMENT MANUAL FOR VIDEO GAME ADDICTION.

Science.gov (United States)

Pallesen, Ståle; Lorvik, Ingjerd Meen; Bu, Eli Hellandsjø; Molde, Helge

2015-10-01

This study investigated the effects of a manualized therapy for video game addiction in 12 males, ages 14-18 yr. The manual was based on cognitive-behavioral therapy, short-term strategic family therapy, solution-focused therapy, and motivational interviewing. Treatment response was reported by the patients, their mothers, and the therapists. The patients reported moderate (but statistically non-significant) improvement from pre- to post-treatment. The mothers, however, reported large effects and statistically significant improvement from pre- to post-treatment. The therapists reported marked or moderate treatment response in six of the 12 patients. The ratings of change by mothers converged well with the views of change of both the patients and therapists, whereas the convergence of views on change between the two latter sources was far lower.

Oskarshamn site investigation. Programme for further investigations of bedrock, soil, water and environment in Laxemar subarea

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-03-15

SKB (the Swedish Nuclear Fuel and Waste Management Co), has been conducting a site investigation at Simpevarp and Laxemar in Oskarshamn for siting of a final repository for spent nuclear fuel. An equivalent investigation is being conducted in Forsmark in Ohmmeter's. The initial part of the site investigations had been completed for the both of the subareas Simpevarp and Laxemar in the autumn of 2004. Based on the results of these investigations, SKB preliminarily prioritized the Laxemar subarea for further investigations. A programme was presented for the first stage of the complete site investigation in the Laxemar subarea, along with the main features of the remainder of the site investigation. The programme included investigations up until the summer of 2005 and was particularly aimed at obtaining answers to several vital questions so that the subsequent investigations could be focused on the rock areas judged to be most suitable for a final repository. These investigations have now been completed. This report presents the programme for the remainder of the site investigation. The points of departure are the general goals for the Deep Repository Project during the site investigation phase, analyses and evaluations of data from completed investigations, and the needs for additional data to be able to evaluate the site as a siting alternative for the final repository. The account mainly covers the investigations on the site. All other work - analyses, site descriptive modelling, facility design, safety assessments and studies and assessments of consequences for the environment, human health and society - are only mentioned to the extent necessary in order to place the investigations in their context. The direction of the site investigation in Oskarshamn and the investigation programme presented in this report is based on SKB's preliminary decision to prioritize the Laxemar subarea for further investigations. A final decision on the direction of the site

Geotechnical investigations of the PEP site

International Nuclear Information System (INIS)

Gould, R.S.

1976-02-01

The purpose of this paper is to summarize the general nature of the geology and rock and soil formations of the PEP site as they relate to the design and construction of the project; to describe site investigation programs and to catalog the geotechnical information presently available about the site. The recently-completed investigation of subterranean conditions around the PEP ring when coupled with previous surveys gives us a good understanding of what to expect with regard to tunneling, undertaking larger underground excavations and constructing research halls are the interaction areas. It bears out the predictions made in Jacobs and Associates' report of 1973; i.e., that the ring housing construction is classified as soft-ground tunneling and that large underground openings, such as region 10 and the injection junction structures, will require great attention to support. A shield or shields will probably be required. On the positive side, the site affords very good conditions for soft-ground tunneling. Water will be a problem in some areas, but not an unsolvable one. The possibility of encountering lethal or explosive gases, almost always the case in tunneling in California's coastal formations, exists but has not been ascertained. Finally, no reasons to change current cost estimates or schedules have merged from the investigation. 13 refs., 1 fig

Site investigations: Strategy for rock mechanics site descriptive model

International Nuclear Information System (INIS)

Andersson, Johan; Christiansson, Rolf; Hudson, John

2002-05-01

As a part of the planning work for the Site Investigations, SKB has developed a Rock Mechanics Site Descriptive Modelling Strategy. Similar strategies are being developed for other disciplines. The objective of the strategy is that it should guide the practical implementation of evaluating site specific data during the Site Investigations. It is also understood that further development may be needed. This methodology enables the crystalline rock mass to be characterised in terms of the quality at different sites, for considering rock engineering constructability, and for providing the input to numerical models and performance assessment calculations. The model describes the initial stresses and the distribution of deformation and strength properties of the intact rock, of fractures and fracture zones, and of the rock mass. The rock mass mechanical properties are estimated by empirical relations and by numerical simulations. The methodology is based on estimation of mechanical properties using both empirical and heroretical/numerical approaches; and estimation of in situ rock stress using judgement and numerical modelling, including the influence of fracture zones. These approaches are initially used separately, and then combined to produce the required characterisation estimates. The methodology was evaluated with a Test Case at the Aespoe Hard Rock Laboratory in Sweden. The quality control aspects are an important feature of the methodology: these include Protocols to ensure the structure and coherence of the procedures used, regular meetings to enhance communication, feedback from internal and external reviewing, plus the recording of an audit trail of the development steps and decisions made. The strategy will be reviewed and, if required, updated as appropriate

Site investigations: Strategy for rock mechanics site descriptive model

Energy Technology Data Exchange (ETDEWEB)

Andersson, Johan [JA Streamflow AB, Aelvsjoe (Sweden); Christiansson, Rolf [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Hudson, John [Rock Engineering Consultants, Welwyn Garden City (United Kingdom)

2002-05-01

As a part of the planning work for the Site Investigations, SKB has developed a Rock Mechanics Site Descriptive Modelling Strategy. Similar strategies are being developed for other disciplines. The objective of the strategy is that it should guide the practical implementation of evaluating site specific data during the Site Investigations. It is also understood that further development may be needed. This methodology enables the crystalline rock mass to be characterised in terms of the quality at different sites, for considering rock engineering constructability, and for providing the input to numerical models and performance assessment calculations. The model describes the initial stresses and the distribution of deformation and strength properties of the intact rock, of fractures and fracture zones, and of the rock mass. The rock mass mechanical properties are estimated by empirical relations and by numerical simulations. The methodology is based on estimation of mechanical properties using both empirical and heroretical/numerical approaches; and estimation of in situ rock stress using judgement and numerical modelling, including the influence of fracture zones. These approaches are initially used separately, and then combined to produce the required characterisation estimates. The methodology was evaluated with a Test Case at the Aespoe Hard Rock Laboratory in Sweden. The quality control aspects are an important feature of the methodology: these include Protocols to ensure the structure and coherence of the procedures used, regular meetings to enhance communication, feedback from internal and external reviewing, plus the recording of an audit trail of the development steps and decisions made. The strategy will be reviewed and, if required, updated as appropriate.

Field manual for reclamation of salt contaminated soils

International Nuclear Information System (INIS)

Burley, M.J.; Lesky, M.; Warren, R.J.

1988-01-01

Saltwater is often produced with crude oil and must be separated from it at a processing facility prior to deep-well injection. Increasing volumes of saltwater have led to pipeline corrosion and an increasing frequency of saltwater spills. A field manual for treating saltwater-contaminated soil was prepared by the Production Research Department of Esso Resources Canada Limited and Husky Oil Operations Limited. The purpose of the manual is to provide field and plant operations with a practical guide for reclaiming brine spills on mineral (agricultural) soil. The manual covers background scientific theory about how saltwater affects the soil, initial steps for treating new spills, site assessment, and reclamation program design, implementation and monitoring. A sample spill site assessment form is included. 8 refs

Green Remediation Best Management Practices: Site Investigation

Science.gov (United States)

The U.S. EPA Principles for Greener Cleanups outline the Agency's policy for evaluating and minimizing the environmental 'footprint' of activities undertaken when cleaning up a contaminated site and conducting site investigation.

Hanford Internal Dosimetry Program Manual, PNL-MA-552

Energy Technology Data Exchange (ETDEWEB)

Carbaugh, Eugene H.; Bihl, Donald E.; Maclellan, Jay A.

2009-09-24

This manual is a guide to the services provided by the Hanford Internal Dosimetry Program (IDP), which is operated by the Pacific Northwest National Laboratory.( ) for the U.S. Department of Energy Richland Operations Office, Office of River Protection and their Hanford Site contractors. The manual describes the roles of and relationships between the IDP and the radiation protection programs of the Hanford Site contractors. Recommendations and guidance are also provided for consideration in implementing bioassay monitoring and internal dosimetry elements of radiation protection programs.

Integrated account of method, site selection and programme prior to the site investigation phase

International Nuclear Information System (INIS)

2000-12-01

In order to dispose of the spent nuclear fuel in a safe manner, SKB plans to site a deep repository and an encapsulation plant with associated canister fabrication and transportation system. After an integrated evaluation of feasibility studies and other material, SKB will proceed with investigations of the rock and studies regarding establishment of the deep disposal system in the municipality of Oskarshamn or in Northern Uppland. The plans also include further study of the prospects for a deep repository in the municipality of Nykoeping. In the municipality of Oskarshamn, SKB plans further studies of a siting of the deep repository at Simpevarp. There SKB wants to initiate site investigations with test drilling. For the encapsulation plant, SKB wants to continue studying a siting at CLAB. In Northern Uppland, SKB plans to study two siting alternatives for the deep repository. One is Forsmark in the municipality of Oesthammar, where SKB wants to initiate a site investigation with test drilling. The other is Tierp north of Skutskaer, where SKB intends to start test drilling in an area north of Tierp. First, however, a suitable drilling area with possible transport solutions needs to be defined. This alternative requires the participation of the municipalities of both Tierp and Aelvkarleby. A siting of the encapsulation plant in Northern Uppland will also be studied. For the municipality of Nykoeping, SKB plans to conduct a new safety assessment for the Fjaellveden area, based on data from previous investigations as well as additional studies of how a deep repository could be arranged. SKB will thereby gather data from yet another geographic and geological region beyond those that are prioritized. No test drilling is planned in Nykoeping. The goal of the site investigation phase is to obtain all permits needed to build the planned facilities. It will take an estimated 7 - 8 years to assemble the requisite supporting material, carry out consultations, compile siting

DbPTM 3.0: an informative resource for investigating substrate site specificity and functional association of protein post-translational modifications.

Science.gov (United States)

Lu, Cheng-Tsung; Huang, Kai-Yao; Su, Min-Gang; Lee, Tzong-Yi; Bretaña, Neil Arvin; Chang, Wen-Chi; Chen, Yi-Ju; Chen, Yu-Ju; Huang, Hsien-Da

2013-01-01

Protein modification is an extremely important post-translational regulation that adjusts the physical and chemical properties, conformation, stability and activity of a protein; thus altering protein function. Due to the high throughput of mass spectrometry (MS)-based methods in identifying site-specific post-translational modifications (PTMs), dbPTM (http://dbPTM.mbc.nctu.edu.tw/) is updated to integrate experimental PTMs obtained from public resources as well as manually curated MS/MS peptides associated with PTMs from research articles. Version 3.0 of dbPTM aims to be an informative resource for investigating the substrate specificity of PTM sites and functional association of PTMs between substrates and their interacting proteins. In order to investigate the substrate specificity for modification sites, a newly developed statistical method has been applied to identify the significant substrate motifs for each type of PTMs containing sufficient experimental data. According to the data statistics in dbPTM, >60% of PTM sites are located in the functional domains of proteins. It is known that most PTMs can create binding sites for specific protein-interaction domains that work together for cellular function. Thus, this update integrates protein-protein interaction and domain-domain interaction to determine the functional association of PTM sites located in protein-interacting domains. Additionally, the information of structural topologies on transmembrane (TM) proteins is integrated in dbPTM in order to delineate the structural correlation between the reported PTM sites and TM topologies. To facilitate the investigation of PTMs on TM proteins, the PTM substrate sites and the structural topology are graphically represented. Also, literature information related to PTMs, orthologous conservations and substrate motifs of PTMs are also provided in the resource. Finally, this version features an improved web interface to facilitate convenient access to the resource.

Transuranic waste characterization sampling and analysis methods manual. Revision 1

International Nuclear Information System (INIS)

Suermann, J.F.

1996-04-01

This Methods Manual provides a unified source of information on the sampling and analytical techniques that enable Department of Energy (DOE) facilities to comply with the requirements established in the current revision of the Transuranic Waste Characterization Quality Assurance Program Plan (QAPP) for the Waste Isolation Pilot Plant (WIPP) Transuranic (TRU) Waste Characterization Program (the Program) and the WIPP Waste Analysis Plan. This Methods Manual includes all of the testing, sampling, and analytical methodologies accepted by DOE for use in implementing the Program requirements specified in the QAPP and the WIPP Waste Analysis Plan. The procedures in this Methods Manual are comprehensive and detailed and are designed to provide the necessary guidance for the preparation of site-specific procedures. With some analytical methods, such as Gas Chromatography/Mass Spectrometry, the Methods Manual procedures may be used directly. With other methods, such as nondestructive characterization, the Methods Manual provides guidance rather than a step-by-step procedure. Sites must meet all of the specified quality control requirements of the applicable procedure. Each DOE site must document the details of the procedures it will use and demonstrate the efficacy of such procedures to the Manager, National TRU Program Waste Characterization, during Waste Characterization and Certification audits

International workshop on site investigation and evaluation based on the siting process in Sweden

International Nuclear Information System (INIS)

Andersson, Johan; Stroem, A.

2001-06-01

SKB's goal is to commence surface based site investigations in 2002. Extensive preparations are now being made for this transition to the next phase in the siting process for the deep repository for spent nuclear fuel. The purpose of the international workshop on site characterisation held at Aespoe April 2001 was to: present the SKB site investigation and evaluation programme to a group of international experts; discuss whether the available toolbox of investigation methods for surface based site investigations is appropriate and state-of-the-art in an international perspective; and by working group sessions discuss the level of ambition in the programme for site investigation for each discipline. This report summarises the conclusions of the workshop in general terms. Many of the detailed comments and ideas obtained at the workshop have already inspired and will also directly inspire the on-going planning work for site characterisation. The core activity at the workshop was the work performed by working groups. They addressed what should be considered for a site characterisation programme, based on the generic planning made so far by SKB. The working groups also outlined site specific characterisation programmes for the sites suggested by SKB. The tasks were strictly confined to technical and scientific modelling issues. The working group chairmen presented the working group results at the workshop and have also submitted short memos to SKB. The present document is a compilation of these memos. The SKB generic programme as presented in the existing top level documents, 'Requirements and Criteria and Overall Programme', received general endorsement and was appreciated for being comprehensive and systematic. For example, it contains comprehensive lists of parameters to be measured. However, there is need for prioritisation and sequencing. This is actually included in the current planning process at SKB where the generic programme later this year will be adapted to

Supplementing Conventional Site Investigation Techniques

African Journals Online (AJOL)

user

School of Civil and& Environmental Engineering, Addis Ababa Institute of Technology, AAU ... particularly drawing on information along sections of deep cut. ... to apply their engineering judgment. .... Though the design manual states that it is.

Parameters of importance to determine during geoscientific site investigation

Energy Technology Data Exchange (ETDEWEB)

Andersson, Johan [QuantiSci AB (Sweden); Almen, K.E. [KEA GEO-Konsult AB (Sweden); Ericsson, Lars O.; Karlsson, Fred; Stroem, A. [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Fredriksson, Anders [ADG Grundteknik AB (Sweden); Stanfors, R. [Roy Stanfors Consulting AB (Sweden)

1998-06-01

This document identifies and describes geo-scientific parameters that are of importance in order to carry out performance and safety assessments of a deep repository for spent nuclear fuel, based on the information that can be obtained from a site investigation. The document also discusses data needs for planning and design of the rock works and for description of other environmental aspects. Evaluation of the different parameters is discussed in the document as well. The document was produced by a working group consisting of the authors and various SKB staff and consultants, and comprises a step in the planning of a geo-scientific investigation programme at the sites where site investigations will be conducted. The goals of the work presented in this report can be derived directly from SKBs ongoing RD and D Programme. The programme stipulates that a geo-scientific site investigation programme must be available before a site investigation begins. This programme is supposed to specify the goals, measurement methods and evaluation methodology, as well as the acceptance criteria against which the site is evaluated. It is pointed out that site evaluation is a collective term for an interactive process consisting of different parts 65 refs, 15 figs, 12 tabs

Near Regional and Site Investigations of the Temelin NPP Site

International Nuclear Information System (INIS)

Prachar, Ivan; Vacek, Jiri; Heralecky, Pavel

2011-01-01

The Temelin NPP is worldwide through heated discussion with nuclear energetic opposition. In addition this discussion goes beyond a border of the Czech Republic. On the other side, results of several international supervisions shown that Temelin NPP is fully comparable with the safest nuclear power plants in the world regarding its technical design and safety functions. This presentation deals with the near regional and site investigations of the Temelin NPP Site. It must be noted that although the Temelin site is situated in the area with low seismicity, item of seismicity is a basic argument against Temelin NPP and therefore a detail seismic hazard assessment was performed

Site investigations for final disposal of high-level nuclear waste

International Nuclear Information System (INIS)

Aeikaes, T.; Laine, T.

1982-12-01

Research concerning disposal of high-level nuclear waste of the Industrial Power Company Ltd has focused on deep underground disposal in Finnish precambrian bedrock. The present target is to have a repository for high-level waste in operation by 2020. Selection of the repository site is based on site investigations. In addition to geosciences, selection of appropriate site includes many branches of studies; engineering, safety analysis, ecology, transport, demography etc. The investigations required for site selection for high-level waste have been arranged in a sequence of four phases. The aim of the phases is that investigations become more and more detailed as the selection process continues. Phase I of the investigations is the characterization of potential areas. This comprises establishment of criteria for site selection and identification of areas that meet selection criteria. Objective of these studies is to determine areas for phase II field investigations. The studies are largely made by reviewing existing data and remote-sensing techniques. Phase II field investigations will be undertaken between 1986-1992. The number of potential candidates for repository site is reduced to few preferred areas by preceeding generic study. The site selection process culminates in phase III in site confirmation studies carried out at 2...3 most suitable sites during 1992-2010. This is then followed by phase IV, which comprises very detailed investigations at the selected site. An alternative for these investigations is to undertake them by using pilot shaft and drifts. Active development is taking place in all phases concerning investigation methods, criteria, parameters, data processing and modelling. The applicability of the various investigation methods and techniques is tested in a deep borehole in phase I. The co-operation with countries with similar geological conditions makes it possible to compare results obtained by different techniques

Internal dosimetry technical basis manual

International Nuclear Information System (INIS)

1990-01-01

The internal dosimetry program at the Savannah River Site (SRS) consists of radiation protection programs and activities used to detect and evaluate intakes of radioactive material by radiation workers. Examples of such programs are: air monitoring; surface contamination monitoring; personal contamination surveys; radiobioassay; and dose assessment. The objectives of the internal dosimetry program are to demonstrate that the workplace is under control and that workers are not being exposed to radioactive material, and to detect and assess inadvertent intakes in the workplace. The Savannah River Site Internal Dosimetry Technical Basis Manual (TBM) is intended to provide a technical and philosophical discussion of the radiobioassay and dose assessment aspects of the internal dosimetry program. Detailed information on air, surface, and personal contamination surveillance programs is not given in this manual except for how these programs interface with routine and special bioassay programs

Internal dosimetry technical basis manual

Energy Technology Data Exchange (ETDEWEB)

1990-12-20

The internal dosimetry program at the Savannah River Site (SRS) consists of radiation protection programs and activities used to detect and evaluate intakes of radioactive material by radiation workers. Examples of such programs are: air monitoring; surface contamination monitoring; personal contamination surveys; radiobioassay; and dose assessment. The objectives of the internal dosimetry program are to demonstrate that the workplace is under control and that workers are not being exposed to radioactive material, and to detect and assess inadvertent intakes in the workplace. The Savannah River Site Internal Dosimetry Technical Basis Manual (TBM) is intended to provide a technical and philosophical discussion of the radiobioassay and dose assessment aspects of the internal dosimetry program. Detailed information on air, surface, and personal contamination surveillance programs is not given in this manual except for how these programs interface with routine and special bioassay programs.

WAG 2 remedial investigation and site investigation site-specific work plan/health and safety checklist for the soil and sediment task

International Nuclear Information System (INIS)

Holt, V.L.; Burgoa, B.B.

1993-12-01

This document is a site-specific work plan/health and safety checklist (WP/HSC) for a task of the Waste Area Grouping 2 Remedial Investigation and Site Investigation (WAG 2 RI ampersand SI). Title 29 CFR Part 1910.120 requires that a health and safety program plan that includes site- and task-specific information be completed to ensure conformance with health- and safety-related requirements. To meet this requirement, the health and safety program plan for each WAG 2 RI ampersand SI field task must include (1) the general health and safety program plan for all WAG 2 RI ampersand SI field activities and (2) a WP/HSC for that particular field task. These two components, along with all applicable referenced procedures, must be kept together at the work site and distributed to field personnel as required. The general health and safety program plan is the Health and Safety Plan for the Remedial Investigation and Site Investigation of Waste Area Grouping 2 at the Oak Ridge National Laboratory, Oak Ridge, Tennessee (ORNL/ER-169). The WP/HSCs are being issued as supplements to ORNL/ER-169

OASIS User Manual

CERN Document Server

Bojtar, L

2009-01-01

The OASIS system has been operational for years now. After a long development the project has reached a state where the number of features it provides exceeds largely what most of its users knows about. The author felt it was time to write a user manual explaining all the functionality of the viewer application. This document is a user manual, concentrating on the functionality of the viewer from the user’s point of view. There are already documents available on the project’s web site about the technical aspects at http://project-oasis.web.cern.ch/project-oasis/presentations.htm . There was an attempt to produce a tutorial on the viewer, but it didn’t get much further than the table of contents, that however is well thought. The structure of this user manual follows the same principle, the basic and most often used features are grouped together. Advanced or less often used features are described in a separate chapter. There is a second organizational principle, features belong to different levels: chann...

78 FR 29616 - Adoption of Updated EDGAR Filer Manual

Science.gov (United States)

2013-05-21

... made in electronic format.\\3\\ Filers may consult the Filer Manual in conjunction with our rules.... We will post electronic format copies on the Commission's Web site; the address for the Filer Manual... the Administrative Procedure Act (APA).\\5\\ It follows that the requirements of the Regulatory...

RCRA Facility Investigation/Remedial Investigation Report for the Grace Road Site (631-22G)

Energy Technology Data Exchange (ETDEWEB)

Palmer, E.

1998-10-02

This report summarizes the activities and documents the results of a Resource Conservation and Recovery Act Facility Investigation/Remedial Investigation conducted at Grace Road Site on the Savannah River Site near Aiken, South Carolina.

RCRA Facility Investigation/Remedial Investigation Report for the Grace Road Site (631-22G)

International Nuclear Information System (INIS)

Palmer, E.

1998-01-01

This report summarizes the activities and documents the results of a Resource Conservation and Recovery Act Facility Investigation/Remedial Investigation conducted at Grace Road Site on the Savannah River Site near Aiken, South Carolina

Salmon Site Remedial Investigation Report, Appendix C

International Nuclear Information System (INIS)

1999-01-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Salmon Site Remedial Investigation Report, Exhibit 2

Energy Technology Data Exchange (ETDEWEB)

USDOE NV

1999-09-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Salmon Site Remedial Investigation Report, Appendix D

International Nuclear Information System (INIS)

1999-01-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Salmon Site Remediation Investigation Report, Appendix A

International Nuclear Information System (INIS)

1999-01-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Salmon Site Remedial Investigation Report, Main Body

Energy Technology Data Exchange (ETDEWEB)

US DOE/NV

1999-09-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Salmon Site Remedial Investigation Report, Exhibit 2

International Nuclear Information System (INIS)

1999-01-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Salmon Site Remedial Investigation Report, Appendix C

Energy Technology Data Exchange (ETDEWEB)

US DOE/NV

1999-09-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Salmon Site Remedial Investigation Report, Exhibit 5

Energy Technology Data Exchange (ETDEWEB)

USDOE/NV

1999-09-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Salmon Site Remedial Investigation Report, Exhibit 5

International Nuclear Information System (INIS)

1999-01-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Hanford Site solid waste acceptance criteria

International Nuclear Information System (INIS)

Willis, N.P.; Triner, G.C.

1991-09-01

Westinghouse Hanford Company manages the Hanford Site solid waste treatment, storage, and disposal facilities for the US Department of Energy Field Office, Richland under contract DE-AC06-87RL10930. These facilities include radioactive solid waste disposal sites, radioactive solid waste storage areas and hazardous waste treatment, storage, and/or disposal facilities. This manual defines the criteria that must be met by waste generators for solid waste to be accepted by Westinghouse Hanford Company for treatment, storage and/or disposal facilities. It is to be used by all waste generators preparing radioactive solid waste for storage or disposal at the Hanford Site facilities and for all Hanford Site generators of hazardous waste. This manual is also intended for use by Westinghouse Hanford Company solid waste technical staff involved with approval and acceptance of solid waste. The criteria in this manual represent a compilation of state and federal regulations; US Department of Energy orders; Hanford Site requirements; and other rules, regulations, guidelines, and standards as they apply to management of solid waste. Where appropriate, these requirements are included in the manual by reference. It is the intent of this manual to provide guidance to the waste generator in meeting the applicable requirements

Summary Staging Manual 2000 - SEER

Science.gov (United States)

Access this manual of codes and coding instructions for the summary stage field for cases diagnosed 2001-2017. 2000 version applies to every anatomic site. It uses all information in the medical record. Also called General Staging, California Staging, and SEER Staging.

Potential energy center site investigations

International Nuclear Information System (INIS)

Savage, W.F.

1977-01-01

Past studies by the AEC, NRC, NSF and others have indicated that energy centers have certain advantages over dispersed siting. There is the need, however, to investigate such areas as possible weather modifications due to major heat releases, possible changes in Federal/state/local laws and institutional arrangements to facilitate implementation of energy centers, and to assess methods of easing social and economic pressures on a surrounding community due to center construction. All of these areas are under study by ERDA, but there remains the major requirement for the study of a potential site to yield a true assessment of the energy center concept. In this regard the Division of Nuclear Research and Applications of ERDA is supporting studies by the Southern and Western Interstate Nuclear Boards to establish state and utility interest in the concept and to carry out screening studies of possible sites. After selection of a final site for center study , an analysis will be made of the center including technical areas such as heat dissipation methods, water resource management, transmission methods, construction methods and schedules, co-located fuel cycle facilities, possible mix of reactor types, etc. Additionally, studies of safeguards, the interaction of all effected entities in the siting, construction, licensing and regulation of a center, labor force considerations in terms of local impact, social and economic changes, and financing of a center will be conducted. It is estimated that the potential site study will require approximately two years

Corrective Action Investigation Plan for Corrective Action Unit 137: Waste Disposal Sites, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

Wickline, Alfred

2005-01-01

This Corrective Action Investigation Plan (CAIP) contains project-specific information including facility descriptions, environmental sample collection objectives, and criteria for conducting site investigation activities at Corrective Action Unit (CAU) 137: Waste Disposal Sites. This CAIP has been developed in accordance with the ''Federal Facility Agreement and Consent Order'' (FFACO) (1996) that was agreed to by the State of Nevada, the U.S. Department of Energy (DOE), and the U.S. Department of Defense. Corrective Action Unit 137 contains sites that are located in Areas 1, 3, 7, 9, and 12 of the Nevada Test Site (NTS), which is approximately 65 miles (mi) northwest of Las Vegas, Nevada (Figure 1-1). Corrective Action Unit 137 is comprised of the eight corrective action sites (CASs) shown on Figure 1-1 and listed below: (1) CAS 01-08-01, Waste Disposal Site; (2) CAS 03-23-01, Waste Disposal Site; (3) CAS 03-23-07, Radioactive Waste Disposal Site; (4) CAS 03-99-15, Waste Disposal Site; (5) CAS 07-23-02, Radioactive Waste Disposal Site; (6) CAS 09-23-07, Radioactive Waste Disposal Site; (7) CAS 12-08-01, Waste Disposal Site; and (8) CAS 12-23-07, Waste Disposal Site. The Corrective Action Investigation (CAI) will include field inspections, radiological surveys, geophysical surveys, sampling of environmental media, analysis of samples, and assessment of investigation results, where appropriate. Data will be obtained to support corrective action alternative evaluations and waste management decisions. The CASs in CAU 137 are being investigated because hazardous and/or radioactive constituents may be present in concentrations that could potentially pose a threat to human health and the environment. Existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives for the CASs. Additional information will be generated by conducting a CAI before evaluating and selecting corrective action

78 FR 60684 - Adoption of Updated EDGAR Filer Manual

Science.gov (United States)

2013-10-02

... acceptance and processing of filings made in electronic format.\\2\\ Filers may consult the Filer Manual in... electronic format copies on the Commission's Web site; the address for the Filer Manual is http://www.sec.gov... Act (APA).\\6\\ It follows that the requirements of the Regulatory Flexibility Act \\7\\ do not apply. \\6...

Hanford Environmental Information System (HEIS) Operator`s Manual. Volume 1

Energy Technology Data Exchange (ETDEWEB)

Schreck, R.I.

1991-10-01

The Hanford Environmental Information System (HEIS) is a consolidated set of automated resources that effectively manage the data gathered during environmental monitoring and restoration of the Hanford Site. The HEIS includes an integrated database that provides consistent and current data to all users and promotes sharing of data by the entire user community. This manual describes the facilities available to the operational user who is responsible for data entry, processing, scheduling, reporting, and quality assurance. A companion manual, the HEIS User`s Manual, describes the facilities available-to the scientist, engineer, or manager who uses the system for environmental monitoring, assessment, and restoration planning; and to the regulator who is responsible for reviewing Hanford Site operations against regulatory requirements and guidelines.

Surface Environmental Surveillance Procedures Manual

Energy Technology Data Exchange (ETDEWEB)

RW Hanf; TM Poston

2000-09-20

Environmental surveillance data are used in assessing the impact of current and past site operations on human health and the environment, demonstrating compliance with applicable local, state, and federal environmental regulations, and verifying the adequacy of containment and effluent controls. SESP sampling schedules are reviewed, revised, and published each calendar year in the Hanford Site Environmental Surveillance Master Sampling Schedule. Environmental samples are collected by SESP staff in accordance with the approved sample collection procedures documented in this manual.

US Fish and Wildlife Service lands biomonitoring operations manual

Energy Technology Data Exchange (ETDEWEB)

Rope, R.C.; Breckenridge, R.P.

1993-08-01

This is Volume 1 of an operations manual designed to facilitate the development of biomonitoring strategies for U.S. Fish and Wildlife Service Lands. It is one component of the U.S. Fish and Wildlife Service Lands Biomonitoring Operations Manual. The Volume contains the Introduction to the Manual, background information on monitoring, and procedures for developing a biomonitoring strategy for Service lands. The purpose of the Biomonitoring Operations Manual is to provide an approach to develop and implement biomonitoring activities to assess the status and trends of U.S. Fish and Wildlife Service trust resources. It also provides field sampline methods and documentation protocols for contaminant monitoring activities. The strategy described in the Manual has been designed as a stand alone process to characterize the presence of contaminants on lands managed by the Service. This process can be sued to develop a monitoring program for any tract of real estate with potential threats from on- or off-site contaminants. Because the process was designed to address concerns for Service lands that span the United States from Alaska to the Tropical Islands, it has a generic format that can be used in al types of ecosystems, however, significant site specific informtion is required to complete the Workbook and make the process work successfully.

Guideline for environmental site investigations in Manitoba : June 1998

International Nuclear Information System (INIS)

1998-06-01

The procedures for the investigation and characterization of contaminated sites in Manitoba are described in an effort to provide a baseline for developing applicable risk-based remedial action and management plans. This document presents information regarding the methods and protocols for sites where the quality of groundwater, surface water, sediments or soil may have been affected by pollutants as a result of past or present usage of the site. The 1998 document focuses on petroleum impacted sites and also includes the requirements for the investigation of sites potentially impacted by other pollutants. It is based on the principles established by the Canadian Council of Ministers of the Environment for the management of sites in Canada and the requirements of the Manitoba Contaminated Sites Remediation and Consequential Amendments Act. Manitoba's petroleum storage program and the hazardous waste management program, including the disposal or treatment of contaminated soils are also summarized

Study of developing nuclear fabrication facility's integrated emergency response manual

International Nuclear Information System (INIS)

Kim, Taeh Yeong; Cho, Nam Chan; Han, Seung Hoon; Moon, Jong Han; Lee, Jin Hang; Min, Guem Young; Han, Ji Ah

2016-01-01

Public begin to pay attention to emergency management. Thus, public's consensus on having high level of emergency management system up to advanced country's is reached. In this social atmosphere, manual is considered as key factor to prevent accident or secure business continuity. Therefore, we first define possible crisis at KEPCO Nuclear Fuel (hereinafter KNF) and also make a 'Reaction List' for each crisis situation at the view of information-design. To achieve it, we analyze several country's crisis response manual and then derive component, indicate duties and roles at the information-design point of view. From this, we suggested guideline to make 'Integrated emergency response manual(IERM)'. The manual we used before have following few problems; difficult to applicate at the site, difficult to deliver information. To complement these problems, we searched manual elements from the view of information-design. As a result, we develop administrative manual. Although, this manual could be thought as fragmentary manual because it confined specific several agency/organization and disaster type

Remedial Investigation of Hanford Site Releases to the Columbia River

International Nuclear Information System (INIS)

Lerch, J.A.

2009-01-01

In south-central Washington State, the Columbia River flows through the U.S. Department of Energy Hanford Site. A primary objective of the Hanford Site cleanup mission is protection of the Columbia River, through remediation of contaminated soil and groundwater that resulted from its weapons production mission. Within the Columbia River system, surface water, sediment, and biota samples related to potential Hanford Site hazardous substance releases have been collected since the start of Hanford operations. The impacts of Hanford Site hazardous substance releases to the Columbia River in areas upstream, within, and downstream of the Hanford Site boundary have been previously investigated as mandated by the U.S. Department of Energy requirements under the Atomic Energy Act. The impacts are now being assessed under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 via a remedial investigation. The Remedial Investigation Work Plan for Hanford Site Releases to the Columbia River has been developed and issued to initiate the remedial investigation. The work plan establishes a phased approach to characterize contaminants, assess current risks, and determine whether or not there is a need for any cleanup actions. Field investigation activities began in October 2008 and are anticipated to continue into Fall 2009 over a 120 mile stretch of the Columbia River. Information gained from performing this remedial investigation will ultimately be used to help make final regulatory decisions for cleaning up Hanford Site contamination that exists in and along the Columbia River. (authors)

Planning for investigation and evaluation of potential repository sites in Sweden

International Nuclear Information System (INIS)

Almen, K.E.; Stroem, A.

1998-01-01

The present stage of siting of the Swedish Deep Repository for spent nuclear fuel involves general siting studies on national and regional scales and feasibility studies on a municipal scale. Based on these studies, two areas will be selected for surface-based site investigations. The geoscientific site information will be used in the site evaluation process, in which performance and safety assessments and design studies are the major activities, in combination with geoscientific characterization. The safety report and EIA document from the site investigation stage will be the most important documents in the application for the siting permit and the permit to construct the deep repository. Detailed characterization will then verify the suitability of the selected site. The programme for geoscientific site investigations is based on experience from more than 20 years of field studies in several SKB projects, such as the Study Site Investigations , the Stripa Project, and the Aespoe Hard Rock Laboratory. The strategies and methodologies developed, implemented and verified within the Aespoe HRL are a very important source of information and know-how for the development of the site investigation programme. The investigations will produce geoscientific models that include all information needed to analyze the long-term safety of a deep repository located in and adapted to the geological conditions of the rock. The type of geoscientific information needed for performance and safety assessment, layout and design, environmental studies and for fundamental geoscientific understanding has been specified and compiled in a 'parameter' report. The general strategy is that performance assessment, layout and design studies will be conducted in parallel with the geoscientific investigations. Information will be transferred at logical occasions, when decisions have to be taken and when feedback is desirable for new investigation steps. The role of the geoscientific evaluation is to

[Organising an investigation site: a national training reference document].

Science.gov (United States)

Cornu, Catherine; David, Frédérique; Duchossoy, Luc; Hansel-Esteller, Sylvie; Bertoye, Pierre-Henri; Giacomino, Alain; Mouly, Stéphane; Diebolt, Vincent; Blazejewski, Sylvie

2014-01-01

Several surveys have shown a declining performance of French investigators in conducting clinical trials. This is partly due to insufficient and heterogeneous investigator training and site organisation. A multidisciplinary group was set up to propose solutions. We describe the tools developed to improve study site organisation. This working group was made up of clinical research experts from academia, industry, drug regulatory authorities, general practice, and consulting. Methods and tools were developed to improve site organisation. The proposed tools mainly focus on increasing investigators' awareness of their responsibilities, their research environment, the importance of a thorough feasibility analysis, and the implementation of active patient recruitment strategies. These tools should be able to improve site organisation and performances in conducting clinical trials. © 2014 Société Française de Pharmacologie et de Thérapeutique.

Bigfoot Field Manual, Version 2.1

Energy Technology Data Exchange (ETDEWEB)

Campbell, J.L.; Burrows, S.; Gower, S.T.; Cohen, W.B.

1999-09-01

The BigFoot Project is funded by the Earth Science Enterprise to collect and organize data to be used in the National Aeronautics and Space Administration's Earth Observing System (EOS) Validation Program. The data collected by the BigFoot Project are unique in being ground-based observations coincident with satellite overpasses. In addition to collecting data, the BigFoot project will develop and test new algorithms for scaling point measurements to the same spatial scales as the EOS satellite products. This BigFoot Field Manual will be used to achieve completeness and consistency of data collected at four initial BigFoot sites and at future sites that may collect similar validation data. Therefore, validation datasets submitted to the Oak Ridge National Laboratory Distributed Active Archive Center that have been compiled in a manner consistent with the field manual will be especially valuable in the validation program.

A geotechnical investigation of a deep ocean site

International Nuclear Information System (INIS)

Freeman, T.J.; Schuttenhelm, R.T.E.

1990-01-01

A site investigation in deep water often relies solely on laboratory tests to evaluate the geotechnical properties of the sediments. This imposes two fundamental limitations on the investigation: The maximum depth to which the properties can be profiled and the uncertainty of sample disturbance and de-pressurization effects on the measured data. This paper uses results from investigations performed in a water depth of 5.4 km at an abyssal plain site, Great Meteor East (GME), to illustrate how ambiguities can arise in laboratory measurements of strength, and discusses how a simple in-situ test, the expendable penetrator, can be used to corroborate the laboratory data

Add Audio and Video to Your Site

CERN Document Server

MacDonald, Matthew

2010-01-01

Nothing spices up websites like cool sound effects (think ker-thunk as visitors press a button) or embedded videos. Think you need a programmer to add sizzle to your site? Think again. This hands-on guide gives you the techniques you need to add video, music, animated GIFs, and sound effects to your site. This Mini Missing Manual is excerpted from Creating a Web Site: The Missing Manual.

“Doing the Wrong Things Right” Site Investigations in Soft Soil

Science.gov (United States)

Jamilus, M. H.; Lim, A. J. M. S.; Azhar, A. T. S.; Azmi, M. A. M.

2016-11-01

Site investigation is a very important process by which geotechnical, geological and other relevant information which might affect the construction or performance of a civil engineering or building project is acquired. However, common practice in site investigations is not always in accordance to the standard that has been defined. Reliability on the information obtained depends upon several factors that involves correct procedures and competent workers and also supervision. Several examples on site investigation methods are discussed in this paper. Explanation on the difference between the site investigation methods used for real practices in the field and how it should be done are discussed in detail. Therefore, it is hoped that site investigation should always be uniquely planned and should be an interactive and flexible process of discovery and changes according to the condition of the soil.

Thermal Site Descriptive Model. A strategy for the model development during site investigations. Version 1.0

International Nuclear Information System (INIS)

Sundberg, Jan

2003-04-01

Site investigations are in progress for the siting of a deep repository for spent nuclear fuel. As part of the planning work, strategies are developed for site descriptive modelling regarding different disciplines, amongst them the thermal conditions. The objective of the strategy for a thermal site descriptive model is to guide the practical implementation of evaluating site specific data during the site investigations. It is understood that further development may be needed. The model describes the thermal properties and other thermal parameters of intact rock, fractures and fracture zones, and of the rock mass. The methodology is based on estimation of thermal properties of intact rock and discontinuities, using both empirical and theoretical/numerical approaches, and estimation of thermal processes using mathematical modelling. The methodology will be used and evaluated for the thermal site descriptive modelling at the Aespoe Hard Rock Laboratory

Geological Site Descriptive Model. A strategy for the model development during site investigations

Energy Technology Data Exchange (ETDEWEB)

Munier, Raymond; Stenberg, Leif [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Stanfors, Roy [Roy Stanfors Consulting, Lund (Sweden); Milnes, Allan Geoffrey [GEA Consulting, Uppsala (Sweden); Hermanson, Jan [Golder Associates, Stockholm (Sweden); Triumf, Carl-Axel [Geovista, Luleaa (Sweden)

2003-04-01

The Swedish Nuclear Fuel and Waste Management Company (SKB) is at present conducting site investigations as a preliminary to building an underground nuclear waste disposal facility in Sweden. This report presents a methodology for constructing, visualising and presenting 3-dimensional geological models, based on data from the site investigations. The methodology integrates with the overall work-flow of the site investigations, from the collection of raw data to the complete site description, as proposed in several earlier technical reports. Further, it is specifically designed for interaction with SICADA - SKB's Site Characterisation Database - and RVS - SKB's Rock Visualisation System. This report is one in a series of strategy documents intended to demonstrate how modelling is to be performed within each discipline. However, it also has a wider purpose, since the geological site descriptive model provides the basic geometrical framework for all the other disciplines. Hence, the wider aim is to present a practical and clear methodology for the analysis and interpretation of input data for use in the construction of the geology-based 3D geometrical model. In addition to the various aspects of modelling described above, the methodology presented here should therefore also provide: guidelines and directives on how systematic interpretation and integration of geo-scientific data from the different investigation methods should be carried out; guidelines on how different geometries should be created in the geological models; guidelines on how the assignment of parameters to the different geological units in RVS should be accomplished; guidelines on the handling of uncertainty at different points in the interpretation process. In addition, it should clarify the relation between the geological model and other models used in the processes of site characterisation, repository layout and safety analysis. In particular, integration and transparency should be

Geological Site Descriptive Model. A strategy for the model development during site investigations

International Nuclear Information System (INIS)

Munier, Raymond; Stenberg, Leif; Stanfors, Roy; Milnes, Allan Geoffrey; Hermanson, Jan; Triumf, Carl-Axel

2003-04-01

The Swedish Nuclear Fuel and Waste Management Company (SKB) is at present conducting site investigations as a preliminary to building an underground nuclear waste disposal facility in Sweden. This report presents a methodology for constructing, visualising and presenting 3-dimensional geological models, based on data from the site investigations. The methodology integrates with the overall work-flow of the site investigations, from the collection of raw data to the complete site description, as proposed in several earlier technical reports. Further, it is specifically designed for interaction with SICADA - SKB's Site Characterisation Database - and RVS - SKB's Rock Visualisation System. This report is one in a series of strategy documents intended to demonstrate how modelling is to be performed within each discipline. However, it also has a wider purpose, since the geological site descriptive model provides the basic geometrical framework for all the other disciplines. Hence, the wider aim is to present a practical and clear methodology for the analysis and interpretation of input data for use in the construction of the geology-based 3D geometrical model. In addition to the various aspects of modelling described above, the methodology presented here should therefore also provide: guidelines and directives on how systematic interpretation and integration of geo-scientific data from the different investigation methods should be carried out; guidelines on how different geometries should be created in the geological models; guidelines on how the assignment of parameters to the different geological units in RVS should be accomplished; guidelines on the handling of uncertainty at different points in the interpretation process. In addition, it should clarify the relation between the geological model and other models used in the processes of site characterisation, repository layout and safety analysis. In particular, integration and transparency should be promoted. The

SFR site investigation. Bedrock Hydrogeochemistry

International Nuclear Information System (INIS)

Nilsson, Ann-Chatrin; Tullborg, Eva-Lena; Smellie, John; Gimeno, Maria J.; Gomez, Javier B.; Auque, Luis F.; Sandstroem, Bjoern; Pedersen, Karsten

2011-11-01

There are plans that the final repository for low and intermediate level radioactive waste, SFR, located about 150 km north of Stockholm, will be extended. Geoscientific studies to define and characterise a suitable bedrock volume for the extended repository have been carried out from 2007 to 2011, and have included the drilling and evaluation of seven new core drilled and four percussion boreholes. These new data, together with existing data extending back to 1985, have been interpreted and modelled in order to provide the necessary information for safety assessment and repository design. This report presents the final hydrogeochemical site description for the SFR site, and will constitute a background report for the integrated site description (the SFR Site Descriptive Model version 1.0) together with corresponding reports from the geological and hydrogeological disciplines. Most of the hydrogeochemical data from the field investigations consist of major ions and isotopes together with sporadic gas, microbe and measured redox data. Despite the close proximity of the Forsmark site, few data from this source are of relevance because of the shallow nature of the SFR site, the fact that SFR is located beneath the Baltic Sea and also the drawdown/upconing impacts of its construction on the hydrogeochemistry. This artificially imposed dynamic flow system is naturally more prevalent along major deformation fracture zones of higher transmissivity, whilst lower transmissive fractures together with the less transmissive bedrock masses between major deformation zones, still retain some evidence of the natural groundwater mixing patterns established prior to the SFR construction. The groundwaters in the SFR dataset cover a depth down to -250 m.a.s.l. with single sampling locations at -300 and -400 m.a.s.l. and represent a relatively limited salinity range (1,500 to 5,500 mg/L chloride). However, the δ 18 O values show a wide variation (-15.5 to -7.5 per mille V

SFR site investigation. Bedrock Hydrogeochemistry

Energy Technology Data Exchange (ETDEWEB)

Nilsson, Ann-Chatrin [Geosigma AB, Uppsala (Sweden); Tullborg, Eva-Lena [Terralogica AB, Graabo (Sweden); Smellie, John [Conterra AB, Uppsala (Sweden); Gimeno, Maria J.; Gomez, Javier B.; Auque, Luis F. [Univ. of Zaragoza, Zaragoza (Spain); Sandstroem, Bjoern [WSP Sverige AB, Goeteborg (Sweden); Pedersen, Karsten [Micans AB, Moelnlycke (Sweden)

2011-11-15

There are plans that the final repository for low and intermediate level radioactive waste, SFR, located about 150 km north of Stockholm, will be extended. Geoscientific studies to define and characterise a suitable bedrock volume for the extended repository have been carried out from 2007 to 2011, and have included the drilling and evaluation of seven new core drilled and four percussion boreholes. These new data, together with existing data extending back to 1985, have been interpreted and modelled in order to provide the necessary information for safety assessment and repository design. This report presents the final hydrogeochemical site description for the SFR site, and will constitute a background report for the integrated site description (the SFR Site Descriptive Model version 1.0) together with corresponding reports from the geological and hydrogeological disciplines. Most of the hydrogeochemical data from the field investigations consist of major ions and isotopes together with sporadic gas, microbe and measured redox data. Despite the close proximity of the Forsmark site, few data from this source are of relevance because of the shallow nature of the SFR site, the fact that SFR is located beneath the Baltic Sea and also the drawdown/upconing impacts of its construction on the hydrogeochemistry. This artificially imposed dynamic flow system is naturally more prevalent along major deformation fracture zones of higher transmissivity, whilst lower transmissive fractures together with the less transmissive bedrock masses between major deformation zones, still retain some evidence of the natural groundwater mixing patterns established prior to the SFR construction. The groundwaters in the SFR dataset cover a depth down to -250 m.a.s.l. with single sampling locations at -300 and -400 m.a.s.l. and represent a relatively limited salinity range (1,500 to 5,500 mg/L chloride). However, the {delta}{sup 18}O values show a wide variation (-15.5 to -7.5 per mille V

Assessing Contractor Capabilities for Streamlined Site Investigations

Science.gov (United States)

The purpose of this document is to familiarize and encourage brownfields decision makers to investigate and employ innovative methods for characterizing their sites, to assist brownfields decision makers in assessing contractors' capabilities.

Site investigations for repositories for solid radioactive wastes in shallow ground

International Nuclear Information System (INIS)

1982-01-01

This report provides an overview and technical guidelines for investigations on a national level for the selection and confirmation of a repository site that will provide adequately safe performance for disposal of solid radioactive wastes that are low- or intermediate-level and short-lived. It also provides basic information on technical activities to be undertaken and on techniques that are available for such investigations in the various steps in selecting suitable sites. The report supplements the information given in Shallow Ground Disposal of Radioactive Wastes: A Guidebook, IAEA Safety Series No. 53 (1981). This report focuses mainly on different aspects of earth sciences and the various investigative techniques relative to earth sciences that may be necessary for site investigations. Some major related studies in other fields are discussed briefly. It is assumed that no previous investigations have been undertaken, and the report proceeds through area site selection to the stage when the site is confirmed as suitable for a waste repository

Site investigations for repositories for solid radioactive wastes in shallow ground

Energy Technology Data Exchange (ETDEWEB)

1982-01-01

This report provides an overview and technical guidelines for investigations on a national level for the selection and confirmation of a repository site that will provide adequately safe performance for disposal of solid radioactive wastes that are low- or intermediate-level and short-lived. It also provides basic information on technical activities to be undertaken and on techniques that are available for such investigations in the various steps in selecting suitable sites. The report supplements the information given in Shallow Ground Disposal of Radioactive Wastes: A Guidebook, IAEA Safety Series No. 53 (1981). This report focuses mainly on different aspects of earth sciences and the various investigative techniques relative to earth sciences that may be necessary for site investigations. Some major related studies in other fields are discussed briefly. It is assumed that no previous investigations have been undertaken, and the report proceeds through area site selection to the stage when the site is confirmed as suitable for a waste repository.

Creating a Website The Missing Manual

CERN Document Server

MacDonald, Matthew

2011-01-01

Think you need an army of skilled programmers to build a website? Think again. With nothing more than an ordinary PC, some raw ambition, and this book, you'll learn how to create and maintain a professional-looking, visitor-friendly site. This Missing Manual gives you all the tools, techniques, and expert advice you need. Plan your site. Create web pages by learning the basics of HTML and HTML5.Control page design with CSS. Format text, images, links, tables, and other elements.Attract visitors. Ensure that people can find your site through popular search engines.Build a community. Add forums

Geochemical investigation of UMTRAP designated site at Durango, Colorado

International Nuclear Information System (INIS)

Markos, G.; Bush, K.J.

1983-09-01

This report is the result of a geochemical investigation of the former uranium mill and tailings site at Durango, Colorado. This is one in a series of site specific geochemical investigations performed on the inactive uranium mill tailings included in the UMTRA Project. The objectives of the investigation are to characterize the geochemistry, to determine the contaminant distribution resulting from the former milling activities and tailings, and to infer chemical pathways and transport mechanisms from the contaminant distribution. The results will be used to model contaminant migration and to develop criteria for long-term containment media such as a cover system which is impermeable to contaminant migration. This report assumes a familiarity with the hydrologic conditions of the site and the geochemical concepts underlying the investigation. The results reported are based on a one-time sampling of waters and solid material from the background, the area adjacent to the site, and the site. The solid samples are water extracted remove easily soluble salts and acids extracted to remove cabonates and hydroxides. The water extracts and solid samples were analyzed for the major and trace elements. A limited number of samples were analyzed for radiological components. The report includes the methods of sampling, sample processing, analysis, and data interpretation. Three major conclusions are: (1) carbonate salts and low TDS characterize the tailings; (2) the adjacent area and raffinate ponds contain contaminants deposited by a single event of fluid permeation of the soils; and (3) the Animas River adjacent to the site has elevated gross alpha activity attributed to 226 Ra in the sediments derived from the tailings or milling activities

Geoscientific programme for investigation and evaluation of sites for the deep repository

International Nuclear Information System (INIS)

2000-08-01

SKB's goal is to be able to commence site investigations in 2002. Extensive preparations are now being made for this transition to the next phase in the siting process for the deep repository. This report describes the investigation and evaluation programme, which is focused on a deep repository in accordance with the KBS-3 method for spent nuclear fuel. When areas for site investigations have been chosen, the programmes will be adapted to the site-specific conditions. The geoscientific work during the site investigation phase is supposed to provide the broad knowledge base that is required to evaluate the suitability of investigated sites for a deep repository. The material must be comprehensive enough to: show whether the selected site satisfies fundamental safety requirements; permit comparisons with other investigated sites; and serve as a basis for adaptation of the deep repository to the properties and characteristics of the site with an acceptable impact on society and the environment. The work is being carried out in consultation with municipalities, regulatory authorities and nearby residents. The main product of the investigations is a site description, which presents collected data and interpreted parameters that are of importance both for the overall scientific understanding of the site and for the analyses and assessments that are made of design and safety assessment with respect to the deep repository's layout and construction as well as its long-term performance and radiological safety. The site description should furthermore present an integrated description of the site (geosphere and biosphere) and its regional environs with respect to current state and naturally ongoing processes. A technical risk evaluation is carried out, by which is meant a description of uncertainties in calculations and the environmental impact of the civil engineering work. The main product of the safety assessment is a safety report, which analyzes whether long-term safety

Geoscientific programme for investigation and evaluation of sites for the deep repository

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-08-01

SKB's goal is to be able to commence site investigations in 2002. Extensive preparations are now being made for this transition to the next phase in the siting process for the deep repository. This report describes the investigation and evaluation programme, which is focused on a deep repository in accordance with the KBS-3 method for spent nuclear fuel. When areas for site investigations have been chosen, the programmes will be adapted to the site-specific conditions. The geoscientific work during the site investigation phase is supposed to provide the broad knowledge base that is required to evaluate the suitability of investigated sites for a deep repository. The material must be comprehensive enough to: show whether the selected site satisfies fundamental safety requirements; permit comparisons with other investigated sites; and serve as a basis for adaptation of the deep repository to the properties and characteristics of the site with an acceptable impact on society and the environment. The work is being carried out in consultation with municipalities, regulatory authorities and nearby residents. The main product of the investigations is a site description, which presents collected data and interpreted parameters that are of importance both for the overall scientific understanding of the site and for the analyses and assessments that are made of design and safety assessment with respect to the deep repository's layout and construction as well as its long-term performance and radiological safety. The site description should furthermore present an integrated description of the site (geosphere and biosphere) and its regional environs with respect to current state and naturally ongoing processes. A technical risk evaluation is carried out, by which is meant a description of uncertainties in calculations and the environmental impact of the civil engineering work. The main product of the safety assessment is a safety report, which analyzes whether long

AECL strategy for surface-based investigations of potential disposal sites and the development of a geosphere model for a site

International Nuclear Information System (INIS)

Whitaker, S.H.; Brown, A.; Davison, C.C.; Gascoyne, M.; Lodha, G.S.; Stevenson, D.R.; Thorne, G.A.; Tomsons, D.

1994-05-01

The objective of this report is to summarize AECL's strategy for surface-based geotechnical site investigations used in screening and evaluating candidate areas and candidate sites for a nuclear fuel waste repository and for the development of geosphere models of sites. The report is one of several prepared by national nuclear fuel waste management programs for the Swedish Nuclear Fuel and Waste Management Co. (SKB) to provide international background on site investigations for SKB's R and D programme on siting.The scope of the report is limited to surface-based investigations of the geosphere, those done at surface or in boreholes drilled from surface. The report discusses AECL's investigation strategy and the methods proposed for use in surface-based reconnaissance and detailed site investigations at potential repository sites. Site investigations done for AECL's Underground Research Laboratory are used to illustrate the approach. The report also discusses AECL's strategy for developing conceptual and mathematical models of geological conditions at sites and the use of these models in developing a model (Geosphere Model) for use in assessing the performance of the disposal system after a repository is closed. Models based on the site data obtained at the URL are used to illustrate the approach. Finally, the report summarizes the lessons learned from AECL's R and D program on site investigations and mentions some recent developments in the R and D program. 120 refs, 33 figs, 7 tabs

AECL strategy for surface-based investigations of potential disposal sites and the development of a geosphere model for a site

Energy Technology Data Exchange (ETDEWEB)

Whitaker, S H; Brown, A; Davison, C C; Gascoyne, M; Lodha, G S; Stevenson, D R; Thorne, G A; Tomsons, D [AECL Research, Whiteshell Labs., Pinawa, MB (Canada)

1994-05-01

The objective of this report is to summarize AECL`s strategy for surface-based geotechnical site investigations used in screening and evaluating candidate areas and candidate sites for a nuclear fuel waste repository and for the development of geosphere models of sites. The report is one of several prepared by national nuclear fuel waste management programs for the Swedish Nuclear Fuel and Waste Management Co. (SKB) to provide international background on site investigations for SKB`s R and D programme on siting.The scope of the report is limited to surface-based investigations of the geosphere, those done at surface or in boreholes drilled from surface. The report discusses AECL`s investigation strategy and the methods proposed for use in surface-based reconnaissance and detailed site investigations at potential repository sites. Site investigations done for AECL`s Underground Research Laboratory are used to illustrate the approach. The report also discusses AECL`s strategy for developing conceptual and mathematical models of geological conditions at sites and the use of these models in developing a model (Geosphere Model) for use in assessing the performance of the disposal system after a repository is closed. Models based on the site data obtained at the URL are used to illustrate the approach. Finally, the report summarizes the lessons learned from AECL`s R and D program on site investigations and mentions some recent developments in the R and D program. 120 refs, 33 figs, 7 tabs.

Sodium safety manual

International Nuclear Information System (INIS)

Hayes, D.J.; Gardiner, R.L.

1980-09-01

The sodium safety manual is based upon more than a decade of experience with liquid sodium at Berkeley Nuclear Laboratories (BNL). It draws particularly from the expertise and experience developed in the course of research work into sodium fires and sodium water reactions. It draws also on information obtained from the UKAEA and other sodium users. Many of the broad principles will apply to other Establishments but much of the detail is specific to BNL and as a consequence its application at other sites may well be limited. Accidents with sodium are at best unpleasant and at worst lethal in an extremely painful way. The object of this manual is to help prevent sodium accidents. It is not intended to give detailed advice on specific precautions for particular situations, but rather to set out the overall strategy which will ensure that sodium activities will be pursued safely. More detail is generally conveyed to staff by the use of local instructions known as Sodium Working Procedures (SWP's) which are not reproduced in this manual although a list of current SWP's is included. Much attention is properly given to the safe design and operation of larger facilities; nevertheless evidence suggests that sodium accidents most frequently occur in small-scale work particularly in operations associated with sodium cleaning and special care is needed in all such cases. (U.K.)

Fixed site neutralization model programmer's manual. Volume 1

International Nuclear Information System (INIS)

Engi, D.; Chapman, L.; Judnick, W.; Blum, R.; Broegler, L.; Lenz, J.; Weinthraub, A.; Ballard, D.

1979-12-01

The Fixed Site Neutralization Model (FSNM) is a stochastic, time-stepped simulation of an engagement process whereby an adversary force attempts to steal or sabotage sensitive (e.g., nuclear) materials being guarded by a security force on a fixed site and a response force that is off-site. FSNM will assist regulatory bodies of the US Government in evaluating fixed site physical protection systems at various installations in a variety of scenarios. Most data input to the Fixed Site Neutralization Model are in binary form. The user's data are transformed into binary form by two supporting modules, the Data Preprocessor (DPP) and the Plex Preprocessor (PPP). Both preprocessors and the FSNM itself are written in FORTRAN. This volume of the program maintenance program contains: introduction, logic descriptions, PLEX data structure, PLEX records, dictionaries, and error conditions and comments

Development of the web-based site investigation flow diagram in repository development program

International Nuclear Information System (INIS)

Yamamoto, Shuichi; Yoshimura, Kimitaka; Ohuchi, Jin; Tsuboya, Takao; Ando, Kenichi

2005-01-01

In siting a repository for high level radioactive wastes (HLW), it is essential for consensus building intelligibly and visually present why and how the area is selected as a suitable site. However 'information asymmetry' exists especially between society and an implementation body because various types of investigation, analysis and assessment are implemented in site characterization on the basis of a wide variety of advanced science and technology. Communication between experts (e.g. surveyors and modelers) is also important for efficient and reliable site investigation/ characterization. The Web-based Site Investigation Flow Diagram (SIFD) has been developed as a tool for information sharing among stake holders and society-jointed decision making. To test applicability of the SIFD, virtual site characterization ('dry run') is performed using the existing site investigation data. It is concluded that the web-based SIFD enhance traceability and transparency of the site investigation/ characterization, and therefore it would be a powerful communication tool among experts for efficient and reliable site investigation/characterization and among stake holders for consensus building

Field manual for stream water and sediment reconnaissance

International Nuclear Information System (INIS)

Ferguson, R.B.; Price, V.; Baucom, E.I.

1977-11-01

A manual is presented that is intended to direct and coordinate field operations, site selection, sample collection, and information codes for the Savannah River Laboratory (SRL) contribution to the National Uranium Resource Evaluation (NURE) program. The manual provides technical direction and public relations information for field sampling teams. The program is being conducted to evaluate domestic uranium resources and to identify favorable areas for commercial exploration. The NURE program is expected to increase the activity of commercial exploration for uranium in the United States

Apparel Research Network (ARN); Apparel Order Processing Module (AOPM): Field User Manual, Version 1

Science.gov (United States)

1997-09-30

changes. Cancel Button Closes the Site Information Screen, abandoning changes. APPAREL ORDER PROCESSING MODULE FIELD USER MANUAL Ordering Official...on the Ordering Official Information Screen. APPAREL ORDER PROCESSING MODULE FIELD USER MANUAL Ordering Official Information Screen (Jjj

Site investigation - equipment for geological, geophysical, hydrogeological and hydrochemical characterization

International Nuclear Information System (INIS)

Almen, K.E.; Fridh, B.; Johansson, B.E.; Sehlstedt, M.

1986-11-01

The investigations are performed within a site investigation program. In total about 60,000 m of cored 56 mm boreholes have been drilled and investigated at eight study sites. A summarized description of the main investigation methods is included. Instruments for geophysical investigations contains equipment for ground measurements as well as for borehole logging. The Geophysical investigations including the borehole radar measurements, are indirect methods for the geological and hydrogeological characterization of the rock formation. Great effort has been laid on the development of hydrogeological instruments for hydraulic tests and groundwater head measurements. In order to obtain hydrochemical investigations with high quality, a complete system for sampling and analysis of ground water has been developed. (orig./PW)

Forsmark site investigation. Interpretation of topographic lineaments 2002

International Nuclear Information System (INIS)

Isaksson, Hans

2003-04-01

SKB performs site investigations for localization of a deep repository for high level radioactive waste. The site investigations are performed in two municipalities; Oesthammar and Oskarshamn. The Forsmark investigation area is situated in Oesthammar, close to the Forsmark nuclear power plant. The purpose of interpretation of lineaments from topographic data is to identify linear features (lineaments), which may correspond to deformation zones in the bedrock. The data will be combined with interpretations of lineaments from airborne geophysical data in order to produce an integrated lineament interpretation for the Forsmark area. This integrated interpretation will be combined with geological data in order to establish a bedrock geological map of the Forsmark area. The area for the lineament interpretation is the same as that selected for the bedrock mapping activities during 2002, i.e. the land area around Forsmark

Salmon Site Remedial Investigation Report, Appendix B (Part 2)

International Nuclear Information System (INIS)

1999-01-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Salmon Site Remedial Investigation Report, Appendix B (Part 1)

International Nuclear Information System (INIS)

1999-01-01

This Salmon Site Remedial Investigation Report provides the results of activities initiated by the U.S. Department of Energy (DOE) to determine if contamination at the Salmon Site poses a current or future risk to human health and the environment. These results were used to develop and evaluate a range of risk-based remedial alternatives. Located in Lamar County, Mississippi, the Salmon Site was used by the U.S. Atomic Energy Commission (predecessor to the DOE) between 1964 and 1970 for two nuclear and two gas explosions conducted deep underground in a salt dome. The testing resulted in the release of radionuclides into the salt dome. During reentry drilling and other site activities, liquid and solid wastes containing radioactivity were generated resulting in surface soil and groundwater contamination. Most of the waste and contaminated soil and water were disposed of in 1993 during site restoration either in the cavities left by the tests or in an injection well. Other radioactive wastes were transported to the Nevada Test Site for disposal. Nonradioactive wastes were disposed of in pits at the site and capped with clean soil and graded. The preliminary investigation showed residual contamination in the Surface Ground Zero mud pits below the water table. Remedial investigations results concluded the contaminant concentrations detected present no significant risk to existing and/or future land users, if surface institutional controls and subsurface restrictions are maintained. Recent sampling results determined no significant contamination in the surface or shallow subsurface. The test cavity resulting from the experiments is contaminated and cannot be economically remediated with existing technologies. The ecological sampling did not detect biological uptake of contaminants in the plants or animals sampled. Based on the current use of the Salmon Site, the following remedial actions were identified to protect both human health and the environment: (1) the

Preliminary site investigation for LL and IL radwaste disposal for Qinshan NPP

International Nuclear Information System (INIS)

Huang Yawen; Chen Zhangru

1993-01-01

With the purpose of selecting a disposal site for the low- and intermediate-level radwastes arising from Qinshan NPP, site investigations were carried out in several districts of Zhejiang Province. Investigation objectives included the circumstances of geology, hydrogeology, environmental ecology, and social economy. On the basis of collected data, five possible sites were recommended for policy-making reference and further investigation

Corrective Action Investigation Plan for Corrective Action Unit 139: Waste Disposal Sites, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

Grant Evenson

2006-01-01

Corrective Action Unit (CAU) 139 is located in Areas 3, 4, 6, and 9 of the Nevada Test Site, which is 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 139 is comprised of the seven corrective action sites (CASs) listed below: (1) 03-35-01, Burn Pit; (2) 04-08-02, Waste Disposal Site; (3) 04-99-01, Contaminated Surface Debris; (4) 06-19-02, Waste Disposal Site/Burn Pit; (5) 06-19-03, Waste Disposal Trenches; (6) 09-23-01, Area 9 Gravel Gertie; and (7) 09-34-01, Underground Detection Station. These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives with the exception of CASs 09-23-01 and 09-34-01. Regarding these two CASs, CAS 09-23-01 is a gravel gertie where a zero-yield test was conducted with all contamination confined to below ground within the area of the structure, and CAS 09-34-01 is an underground detection station where no contaminants are present. Additional information will be obtained by conducting a corrective action investigation (CAI) before evaluating corrective action alternatives and selecting the appropriate corrective action for the other five CASs where information is insufficient. The results of the field investigation will support a defensible evaluation of viable corrective action alternatives that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed on January 4, 2006, by representatives of the Nevada Division of Environmental Protection; U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office; Stoller-Navarro Joint Venture; and Bechtel Nevada. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 139

Site description of the SFR area at Forsmark at completion of the site investigation phase. SDM-PSU Forsmark

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-05-15

The site descriptive model (SDM) presented in this report is an integrated model for bedrock geology, rock mechanics, bedrock hydrogeology and bedrock hydrogeochemistry of the site investigated in the SFR extension project (PSU). A description of the surface system is also included in the report. However, the surface system is not integrated with the other disciplines as new data regarding the surface system will not be available until after the completion of SDM-PSU. It is noted that SDM-PSU does not include all disciplines handled in SDM-Site Forsmark (SKB 2008b), the focus is to produce a site description that meets the needs of the SFR extension project. The overall objective of the SFR extension project is to have the application for the extension ready by 2013. This report presents an integrated site model incorporating the historic data acquired from the investigations for and construction of the existing SFR facility (1980-1986), as well as from the recent investigations for the planned extension of SFR (2008-2009). It also provides a summary of the abundant underlying data and the discipline-specific models that support the integrated site model. The description relies heavily on background reports concerning detailed data analyses and modelling in the different disciplines. It is noteworthy that the investigations conducted during the SFR extension project were guided by the choice of site prior to the investigations, which was based on the experience gained during the construction of the existing SFR facility.

Site description of the SFR area at Forsmark at completion of the site investigation phase. SDM-PSU Forsmark

International Nuclear Information System (INIS)

2013-05-01

The site descriptive model (SDM) presented in this report is an integrated model for bedrock geology, rock mechanics, bedrock hydrogeology and bedrock hydrogeochemistry of the site investigated in the SFR extension project (PSU). A description of the surface system is also included in the report. However, the surface system is not integrated with the other disciplines as new data regarding the surface system will not be available until after the completion of SDM-PSU. It is noted that SDM-PSU does not include all disciplines handled in SDM-Site Forsmark (SKB 2008b), the focus is to produce a site description that meets the needs of the SFR extension project. The overall objective of the SFR extension project is to have the application for the extension ready by 2013. This report presents an integrated site model incorporating the historic data acquired from the investigations for and construction of the existing SFR facility (1980-1986), as well as from the recent investigations for the planned extension of SFR (2008-2009). It also provides a summary of the abundant underlying data and the discipline-specific models that support the integrated site model. The description relies heavily on background reports concerning detailed data analyses and modelling in the different disciplines. It is noteworthy that the investigations conducted during the SFR extension project were guided by the choice of site prior to the investigations, which was based on the experience gained during the construction of the existing SFR facility

Hanford Environmental Information System (HEIS) user's manual

International Nuclear Information System (INIS)

1991-10-01

The Hanford Environmental Information System (HEIS) is a consolidated set of automated resources that effectively manage the data gathered during environmental monitoring and restoration of the Hanford Site. The HEIS includes an integrated database that provides consistent and current data to all users and promotes sharing of data by the entire user community. Data stored in the HEIS are collected under several regulatory programs. Currently these include the Comprehensive Environmental Response, Compensation and Liability Act of 1980 (CERCLA); the Resource Conservation and Recovery Act of 1976 (RCRA); and the Ground-Water Environmental Surveillance Project, managed by the Pacific Northwest Laboratory. The HEIS is an information system with an inclusive database. The manual, the HEIS User's Manual, describes the facilities available to the scientist, engineer, or manager who uses the system for environmental monitoring, assessment, and restoration planning; and to the regulator who is responsible for reviewing Hanford Site operations against regulatory requirements and guidelines

WAG 2 remedial investigation and site investigation site-specific work plan/health and safety checklist for the ecological assessment task, Kingfisher Study

International Nuclear Information System (INIS)

Holt, V.L.; Baron, L.A.

1994-05-01

This report provides specific details and requirements for the WAG 2 remedial investigation and site investigation Ecological Assessment Task, Kingfisher Study, including information that will contribute to safe completion of the project. The report includes historical background; a site map; project organization; task descriptions and hazard evaluations; controls; and monitoring, personal protective equipment, decontamination, and medical surveillance program requirements. The report also includes descriptions of site personnel and their certifications as well as suspected WAG 2 contaminants and their characteristics. The primary objective of the WAG 2 Kingfisher Study is to assess the feasibility of using kingfishers as biological monitors of contaminants on the Oak Ridge Reservation (ORR). Kingfisher sample collection will be used to determine the levels of contaminants and degree of bioaccumulation within a common piscivorous bird feeding on contaminated fish from streams on the ORR

Attract Visitors to Your Site

CERN Document Server

MacDonald, Matthew

2010-01-01

To be a success, a website has to attract-and keep--visitors. This Mini Missing Manual shows you how to attract new and return visitors and use the power of keywords and Web search engines to rise up in the rankings of search results. You'll also learn how to use a powerful-and free--service that tracks visitor activity on your site so you know which of your Web pages they love, and-just as important--which pages don't work for them. Using this information, you can fine-tune your site to keep the visitors coming. This Mini Missing Manual is excerpted from Creating a Web Site: The Missing Man

Proposed quality assurance manual for the Office of Waste Isolation

International Nuclear Information System (INIS)

1977-01-01

The manual provides guidelines for assuring safe and reliable siting, design, procurement and construction, operation, and decommissioning of a radioactive waste repository. The organization of the program is given and the program itself is defined. The program includes the site evaluation, site selection, design, procurement, fabrication, installation, and testing of any system or component that is safety related. It also included all necessary documentation and auditing

Part 2: Conserving and Planting Trees at Development Sites

Science.gov (United States)

Karen Cappiella; Tom Schueler; Tiffany Wright

2006-01-01

This manual presents specific ways to enable developers, engineers or landscape architects to incorporate more trees into a development site. The proposed approach focuses on protecting existing trees, planting trees in storm water treatment practices, and planting trees in other open spaces at the development site. This manual introduces conceptual designs for storm...

Site descriptive modeling as a part of site characterization in Sweden - Concluding the surface based investigations

International Nuclear Information System (INIS)

Andersson, Johan; Winberg, Anders; Skagius, Kristina; Stroem, Anders; Lindborg, Tobias

2007-01-01

The Swedish Nuclear Fuel and Waste Management Co., SKB, is currently finalizing its surface based site investigations for the final repository for spent nuclear fuel in the municipalities of Oestharmnar (the Forsmark area) and Oskarshamn (the Simpevar/Laxemar area). The investigation data are assessed into a Site Descriptive Model, constituting a synthesis of geology, rock mechanics, thermal properties, hydrogeology, hydro-geochemistry, transport properties and a surface system description. Site data constitute a wide range of different measurement results. These data both need to be checked for consistency and to be interpreted into a format more amenable for three-dimensional modeling. The three-dimensional modeling (i.e. estimating the distribution of parameter values in space) is made in a sequence where the geometrical framework is taken from the geological models and in turn used by the rock mechanics, thermal and hydrogeological modeling. These disciplines in turn are partly interrelated, and also provide feedback to the geological modeling, especially if the geological description appears unreasonable when assessed together with the other data. Procedures for assessing the uncertainties and the confidence in the modeling have been developed during the course of the site modeling. These assessments also provide key input to the completion of the site investigation program. (authors)

Characterization of hazardous waste sites: a methods manual. Volume 2. Available sampling methods (second edition)

International Nuclear Information System (INIS)

Ford, P.J.; Turina, P.J.; Seely, D.E.

1984-12-01

Investigations at hazardous waste sites and sites of chemical spills often require on-site measurements and sampling activities to assess the type and extent of contamination. This document is a compilation of sampling methods and materials suitable to address most needs that arise during routine waste site and hazardous spill investigations. The sampling methods presented in this document are compiled by media, and were selected on the basis of practicality, economics, representativeness, compatability with analytical considerations, and safety, as well as other criteria. In addition to sampling procedures, sample handling and shipping, chain-of-custody procedures, instrument certification, equipment fabrication, and equipment decontamination procedures are described. Sampling methods for soil, sludges, sediments, and bulk materials cover the solids medium. Ten methods are detailed for surface waters, groundwater and containerized liquids; twelve are presented for ambient air, soil gases and vapors, and headspace gases. A brief discussion of ionizing radiation survey instruments is also provided

Corrective Action Investigation Plan for Corrective Action Unit 137: Waste Disposal Sites, Nevada Test Site, Nevada, Rev. No.:0

Energy Technology Data Exchange (ETDEWEB)

Wickline, Alfred

2005-12-01

This Corrective Action Investigation Plan (CAIP) contains project-specific information including facility descriptions, environmental sample collection objectives, and criteria for conducting site investigation activities at Corrective Action Unit (CAU) 137: Waste Disposal Sites. This CAIP has been developed in accordance with the ''Federal Facility Agreement and Consent Order'' (FFACO) (1996) that was agreed to by the State of Nevada, the U.S. Department of Energy (DOE), and the U.S. Department of Defense. Corrective Action Unit 137 contains sites that are located in Areas 1, 3, 7, 9, and 12 of the Nevada Test Site (NTS), which is approximately 65 miles (mi) northwest of Las Vegas, Nevada (Figure 1-1). Corrective Action Unit 137 is comprised of the eight corrective action sites (CASs) shown on Figure 1-1 and listed below: (1) CAS 01-08-01, Waste Disposal Site; (2) CAS 03-23-01, Waste Disposal Site; (3) CAS 03-23-07, Radioactive Waste Disposal Site; (4) CAS 03-99-15, Waste Disposal Site; (5) CAS 07-23-02, Radioactive Waste Disposal Site; (6) CAS 09-23-07, Radioactive Waste Disposal Site; (7) CAS 12-08-01, Waste Disposal Site; and (8) CAS 12-23-07, Waste Disposal Site. The Corrective Action Investigation (CAI) will include field inspections, radiological surveys, geophysical surveys, sampling of environmental media, analysis of samples, and assessment of investigation results, where appropriate. Data will be obtained to support corrective action alternative evaluations and waste management decisions. The CASs in CAU 137 are being investigated because hazardous and/or radioactive constituents may be present in concentrations that could potentially pose a threat to human health and the environment. Existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives for the CASs. Additional information will be generated by conducting a CAI before evaluating and selecting

Investigations on the quality of manual image segmentation in 3D radiotherapy planning

International Nuclear Information System (INIS)

Perelmouter, J.; Tuebingen Univ.; Bohsung, J.; Nuesslin, F.; Becker, G.; Kortmann, R.D.; Bamberg, M.

1998-01-01

In 3D radiotherapy planning image segmentation plays an important role in the definition process of target volume and organs at risk. Here, we present a method to quantify the technical precision of the manual image segmentation process. To validate our method we developed a virtual phantom consisting of several geometrical objects of changing form and contrast, which should be contoured by volunteers using the TOMAS tool for manual segmentation of the Heidelberg VOXELPLAN system. The results of this examination are presented. (orig.) [de

Corrective Action Investigation Plan for Corrective Action Unit 554: Area 23 Release Site, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

Boehlecke, Robert F.

2004-01-01

This Corrective Action Investigation Plan (CAIP) contains project-specific information for conducting site investigation activities at Corrective Action Unit (CAU) 554: Area 23 Release Site, Nevada Test Site, Nevada. Information presented in this CAIP includes facility descriptions, environmental sample collection objectives, and criteria for the selection and evaluation of environmental samples. Corrective Action Unit 554 is located in Area 23 of the Nevada Test Site, which is 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 554 is comprised of one Corrective Action Site (CAS), which is: 23-02-08, USTs 23-115-1, 2, 3/Spill 530-90-002. This site consists of soil contamination resulting from a fuel release from underground storage tanks (USTs). Corrective Action Site 23-02-08 is being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives. Additional information will be obtained by conducting a corrective action investigation prior to evaluating corrective action alternatives and selecting the appropriate corrective action for this CAS. The results of the field investigation will support a defensible evaluation of viable corrective action alternatives that will be presented in the Corrective Action Decision Document for CAU 554. Corrective Action Site 23-02-08 will be investigated based on the data quality objectives (DQOs) developed on July 15, 2004, by representatives of the Nevada Division of Environmental Protection; U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office; and contractor personnel. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 554. Appendix A provides a detailed discussion of the DQO methodology and the DQOs specific to CAS 23-02-08. The scope of the corrective action investigation

Study of developing nuclear fabrication facility's integrated emergency response manual

Energy Technology Data Exchange (ETDEWEB)

Kim, Taeh Yeong; Cho, Nam Chan; Han, Seung Hoon; Moon, Jong Han; Lee, Jin Hang [KEPCO, Daejeon (Korea, Republic of); Min, Guem Young; Han, Ji Ah [Dongguk Univ., Daejeon (Korea, Republic of)

2016-05-15

Public begin to pay attention to emergency management. Thus, public's consensus on having high level of emergency management system up to advanced country's is reached. In this social atmosphere, manual is considered as key factor to prevent accident or secure business continuity. Therefore, we first define possible crisis at KEPCO Nuclear Fuel (hereinafter KNF) and also make a 'Reaction List' for each crisis situation at the view of information-design. To achieve it, we analyze several country's crisis response manual and then derive component, indicate duties and roles at the information-design point of view. From this, we suggested guideline to make 'Integrated emergency response manual(IERM)'. The manual we used before have following few problems; difficult to applicate at the site, difficult to deliver information. To complement these problems, we searched manual elements from the view of information-design. As a result, we develop administrative manual. Although, this manual could be thought as fragmentary manual because it confined specific several agency/organization and disaster type.

The Nirex Sellafield site investigation: the role of geophysical interpretation

International Nuclear Information System (INIS)

Muir Wood, R.; Woo, G.; MacMillan, G.

1992-01-01

This report reviews the methods by which geophysical data are interpreted, and used to characterize the 3-D geology of a site for potential storage of radioactive waste. The report focuses on the NIREX site investigation at Sellafield, for which geophysical observations provide a significant component of the structural geological understanding. In outlining the basic technical principles of seismic data processing and interpretation, and borehole logging, an attempt has been made to identify errors, uncertainties, and the implicit use of expert judgement. To enhance the reliability of a radiological probabilistic risk assessment, recommendations are proposed for independent use of the primary NIREX geophysical site investigation data in characterizing the site geology. These recommendations include quantitative procedures for undertaking an uncertainty audit using a combination of statistical analysis and expert judgement. (author)

Peace Corps Aquaculture Training Manual. Training Manual T0057.

Science.gov (United States)

Peace Corps, Washington, DC. Information Collection and Exchange Div.

This Peace Corps training manual was developed from two existing manuals to provide a comprehensive training program in fish production for Peace Corps volunteers. The manual encompasses the essential elements of the University of Oklahoma program that has been training volunteers in aquaculture for 25 years. The 22 chapters of the manual are…

Geological and geotechnical investigations for nuclear power plants sites

International Nuclear Information System (INIS)

Alves, P.R.R.

1984-09-01

This dissertation presents a general methodology for the tasks of geological and geotechnical investigations, to be performed in the proposed sites for construction of nuclear Power Plants. In this work, items dealing with the standards applied to licensing of Nuclear Power Plants, with the selection process of sites and identification of geological and geotechnical parameters needed for the regional and local characterization of the area being studied, were incorporated. This dissertation also provides an aid to the writing of Technical Reports, which are part of the documentation an owner of a Nuclear Power Plant needs to submit to the Comissao Nacional de Energia Nuclear, to fulfill the nuclear installation licensing requirements. Moreover, this work can contribute to the planning of field and laboratory studies, needed to determine the parameters of the area under investigation, for the siting of Nuclear Power Plants. (Author) [pt

Hydrogeochemical site descriptive model - a strategy for the model development during site investigations

Energy Technology Data Exchange (ETDEWEB)

Smellie, John [Conterra AB, Uppsala (Sweden); Laaksoharju, Marcus [GeoPoint AB, Sollentuna (Sweden); Tullborg, Eva-Lena [Terralogica AB, Graabo (Sweden)

2002-12-01

In 2002, SKB commenced site characterisation investigations using deep boreholes at different sites. As an integral part of the planning work SKB has prepared a strategy to develop a Hydrogeochemical Site Descriptive Model; similar strategies have been developed for the other major geoscience disciplines. The main objectives of the Hydrogeochemical Site Descriptive Model are to describe the chemistry and distribution of the groundwater in the bedrock and overburden and the hydrogeochemical processes involved in its origin and evolution. This description is based primarily on measurements of the groundwater composition but incorporates the use of available geological and hydrogeological site descriptive models. The SKB hydrogeochemistry programme is planned to fulfil two basic requirements: 1) to provide representative and quality assured data for use as input parameter values in calculating long-term repository safety, and 2) to understand the present undisturbed hydrogeochemical conditions and how these conditions will change in the future. Parameter values for safety analysis include pH, Eh, S, SO{sub 4}, HCO{sub 3}, HPO{sub 4} and TDS (mainly cations), together with colloids, fulvic and humic acids, other organics, bacteria and nitrogen. These values will be used to characterise the groundwater environment at, above and below repository depths. In the hydrogeochemical site investigation programme the number and location of the sampling points will be constrained by: a) geology (e.g. topography, overburden types, bedrock structures etc), b) hydrogeology (e.g. groundwater recharge/discharge areas, residence times), c) reliability (e.g. undisturbed vs disturbed groundwater chemical conditions), and d) resources (e.g. number and type of samples, and also available personnel, may be restricted by budgetary and schedule concerns). Naturally a balance is required between these constraints and the scientific aims of the programme. The constraints should never

SNL/CA Environmental Management System Program Manual.

Energy Technology Data Exchange (ETDEWEB)

Larsen, Barbara L.

2005-09-01

The Sandia National Laboratories, California (SNL/CA) Environmental Management System (EMS) Program Manual documents the elements of the site EMS Program. The SNL/CA EMS Program was developed in accordance with Department of Energy (DOE) Order 450.1 and incorporates the elements of the International Standard on Environmental Management Systems, ISO 14001.

Hydrogeochemical site descriptive model - a strategy for the model development during site investigations

International Nuclear Information System (INIS)

Smellie, John; Laaksoharju, Marcus; Tullborg, Eva-Lena

2002-12-01

In 2002, SKB commenced site characterisation investigations using deep boreholes at different sites. As an integral part of the planning work SKB has prepared a strategy to develop a Hydrogeochemical Site Descriptive Model; similar strategies have been developed for the other major geoscience disciplines. The main objectives of the Hydrogeochemical Site Descriptive Model are to describe the chemistry and distribution of the groundwater in the bedrock and overburden and the hydrogeochemical processes involved in its origin and evolution. This description is based primarily on measurements of the groundwater composition but incorporates the use of available geological and hydrogeological site descriptive models. The SKB hydrogeochemistry programme is planned to fulfil two basic requirements: 1) to provide representative and quality assured data for use as input parameter values in calculating long-term repository safety, and 2) to understand the present undisturbed hydrogeochemical conditions and how these conditions will change in the future. Parameter values for safety analysis include pH, Eh, S, SO 4 , HCO 3 , HPO 4 and TDS (mainly cations), together with colloids, fulvic and humic acids, other organics, bacteria and nitrogen. These values will be used to characterise the groundwater environment at, above and below repository depths. In the hydrogeochemical site investigation programme the number and location of the sampling points will be constrained by: a) geology (e.g. topography, overburden types, bedrock structures etc), b) hydrogeology (e.g. groundwater recharge/discharge areas, residence times), c) reliability (e.g. undisturbed vs disturbed groundwater chemical conditions), and d) resources (e.g. number and type of samples, and also available personnel, may be restricted by budgetary and schedule concerns). Naturally a balance is required between these constraints and the scientific aims of the programme. The constraints should never detrimentally affect

Geo-scientific basis for the investigation site Oberbauenstock. Volume 1

International Nuclear Information System (INIS)

Schneider, T.R.; Kappeler, S.W.

1984-12-01

The geological and hydrogeological conditions prevailing in the region of the investigation site Oberbauen Stock have been chosen as model data-set, in the frame of project Gewaehr 1985, for a type B (low and intermediate level) waste repository. The report, in its capacity as a reference report for project Gewaehr presents all available, relevant site data applicable to modeling of the site. The sources of the data are presented. Geological studies and investigations, boreholes and geophysical investigations prior to the construction of the Seelisberg tunnel (as well as all underground facilities pertaining to the said tunnel) are described. In the section devoted to geology, the stratigraphy and the tectonics of the helvetic nappes in the area of the site are described. Further, the host rock, the neighbouring formations and the local tectonics are presented. In conclusion the geological boundary conditions of the area are summarized. The section devoted to hydrogeology deals with the observations and measurements carried out at the surface and in the underground facilities. As well, the present state of knowledge concerning the water chemistry is described. The section also includes a description of the regional hydrogeology. Concerning rock mechanics a summary and discussion of all available parameters and excavation classes is presented. A description of all the experiences acquired during construction follows as a second part. The section ends with a presentation of the observations and measurements of the gas content of the host rock and other formations. A section concerning long-term behaviour concludes the report. Possible future changes of the geology and the climate are investigated. The consequences for the model site are discussed. It is concluded that a negative impact to a repository on the site is improbable on a timescale of 10 5 years. (author)

Preliminary safety evaluation, based on initial site investigation data. Planning document

International Nuclear Information System (INIS)

Hedin, Allan

2002-12-01

This report is a planning document for the preliminary safety evaluations (PSE) to be carried out at the end of the initial stage of SKBs ongoing site investigations for a deep repository for spent nuclear fuel. The main purposes of the evaluations are to determine whether earlier judgements of the suitability of the candidate area for a deep repository with respect to long-term safety holds up in the light of borehole data and to provide feed-back to continued site investigations and site specific repository design. The preliminary safety evaluations will be carried out by a safety assessment group, based on a site model, being part of a site description, provided by a site modelling group and a repository layout within that model suggested by a repository engineering group. The site model contains the geometric features of the site as well as properties of the host rock. Several alternative interpretations of the site data will likely be suggested. Also the biosphere is included in the site model. A first task for the PSE will be to compare the rock properties described in the site model to previously established criteria for a suitable host rock. This report gives an example of such a comparison. In order to provide more detailed feedback, a number of thermal, hydrological, mechanical and chemical analyses of the site will also be included in the evaluation. The selection of analyses is derived from the set of geosphere and biosphere analyses preliminarily planned for the comprehensive safety assessment named SR-SITE, which will be based on a complete site investigation. The selection is dictated primarily by the expected feedback to continued site investigations and by the availability of data after the PSE. The repository engineering group will consider several safety related factors in suggesting a repository layout: Thermal calculations will be made to determine a minimum distance between canisters avoiding canister surface temperatures above 100 deg C

Corrective Action Investigation Plan for Corrective Action Unit 573: Alpha Contaminated Sites, Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Matthews, Patrick

2014-05-01

Corrective Action Unit (CAU) 573 is located in Area 5 of the Nevada National Security Site, which is approximately 65 miles northwest of Las Vegas, Nevada. CAU 573 is a grouping of sites where there has been a suspected release of contamination associated with non-nuclear experiments and nuclear testing. This document describes the planned investigation of CAU 573, which comprises the following corrective action sites (CASs): • 05-23-02, GMX Alpha Contaminated Area • 05-45-01, Atmospheric Test Site - Hamilton These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives.

Ground Snow Measurements: Comparisons of the Hotplate, Weighing and Manual Methods

Science.gov (United States)

Wettlaufer, A.; Snider, J.; Campbell, L. S.; Steenburgh, W. J.; Burkhart, M.

2015-12-01

The Yankee Environmental Systems (YES) Hotplate was developed to avoid some of the problems associated with weighing snowfall sensors. This work compares Hotplate, weighing sensor (ETI NOAH-II) and manual measurements of liquid-equivalent depth. The main field site was at low altitude in western New York; Hotplate and ETI comparisons were also made at two forested subalpine sites in southeastern Wyoming. The manual measurement (only conducted at the New York site) was derived by weighing snow cores sampled from a snow board. The two recording gauges (Hotplate and ETI) were located within 5 m of the snow board. Hotplate-derived accumulations were corrected using a wind-speed dependent catch efficiency and the ETI orifice was heated and alter shielded. Three important findings are evident from the comparisons: 1) The Yes-derived accumulations, recorded in a user-accessible file, were compared to accumulations derived using an in-house calibration and fundamental measurements (plate power, long and shortwave radiances, wind speed, and temperature). These accumulations are highly correlated (N=24; r2=0.99), but the YES-derived values are larger by 20%. 2) The in-house Hotplate accumulations are in good agreement with ETI-based accumulations but with larger variability (N=24; r2=0.88). 3) The comparison of in-house Hotplate accumulation versus manual accumulation, expressed as mm of liquid, exhibits a fitted linear relationship Y (in-house) versus X (manual) given by Y = -0.2 (±1.4) + 0.9 (±0.1) · X (N= 20; r2=0.89). Thus, these two methods agree within statistical uncertainty.

Development of a manualized protocol of massage therapy for clinical trials in osteoarthritis

Directory of Open Access Journals (Sweden)

Ali Ather

2012-10-01

Full Text Available Abstract Background Clinical trial design of manual therapies may be especially challenging as techniques are often individualized and practitioner-dependent. This paper describes our methods in creating a standardized Swedish massage protocol tailored to subjects with osteoarthritis of the knee while respectful of the individualized nature of massage therapy, as well as implementation of this protocol in two randomized clinical trials. Methods The manualization process involved a collaborative process between methodologic and clinical experts, with the explicit goals of creating a reproducible semi-structured protocol for massage therapy, while allowing some latitude for therapists’ clinical judgment and maintaining consistency with a prior pilot study. Results The manualized protocol addressed identical specified body regions with distinct 30- and 60-min protocols, using standard Swedish strokes. Each protocol specifies the time allocated to each body region. The manualized 30- and 60-min protocols were implemented in a dual-site 24-week randomized dose-finding trial in patients with osteoarthritis of the knee, and is currently being implemented in a three-site 52-week efficacy trial of manualized Swedish massage therapy. In the dose-finding study, therapists adhered to the protocols and significant treatment effects were demonstrated. Conclusions The massage protocol was manualized, using standard techniques, and made flexible for individual practitioner and subject needs. The protocol has been applied in two randomized clinical trials. This manualized Swedish massage protocol has real-world utility and can be readily utilized both in the research and clinical settings. Trial registration Clinicaltrials.gov NCT00970008 (18 August 2009

Manual vs. computer-assisted sperm analysis: can CASA replace manual assessment of human semen in clinical practice?

Science.gov (United States)

Talarczyk-Desole, Joanna; Berger, Anna; Taszarek-Hauke, Grażyna; Hauke, Jan; Pawelczyk, Leszek; Jedrzejczak, Piotr

2017-01-01

The aim of the study was to check the quality of computer-assisted sperm analysis (CASA) system in comparison to the reference manual method as well as standardization of the computer-assisted semen assessment. The study was conducted between January and June 2015 at the Andrology Laboratory of the Division of Infertility and Reproductive Endocrinology, Poznań University of Medical Sciences, Poland. The study group consisted of 230 men who gave sperm samples for the first time in our center as part of an infertility investigation. The samples underwent manual and computer-assisted assessment of concentration, motility and morphology. A total of 184 samples were examined twice: manually, according to the 2010 WHO recommendations, and with CASA, using the program set-tings provided by the manufacturer. Additionally, 46 samples underwent two manual analyses and two computer-assisted analyses. The p-value of p CASA and manually. In the group of patients where all analyses with each method were performed twice on the same sample we found no significant differences between both assessments of the same probe, neither in the samples analyzed manually nor with CASA, although standard deviation was higher in the CASA group. Our results suggest that computer-assisted sperm analysis requires further improvement for a wider application in clinical practice.

Field manual for ground water reconnaissance. Savannah River Laboratory National Uranium Resource Evaluation Program

International Nuclear Information System (INIS)

Ferguson, R.B.; Price, V.; Baucom, E.I.

1977-01-01

A manual is presented that is intended to direct and coordinate field operations, site selection, groundwater sample collection, and information codes for the Savannah River Laboratory (SRL) contribution to the National Uranium Resource Evaluation (NURE) program. The manual provides public relations information for field sampling teams as well as technical direction

Return on interactivity? The characteristics and effectiveness of Web sites during the 2010 Dutch local elections

NARCIS (Netherlands)

van Noort, G.; Vliegenthart, R.; Kruikemeier, S.

2016-01-01

This article examines the use of interactive features (i.e., discussion and participation features) on the Web sites of Dutch political parties during the 2010 local elections campaign and investigates whether a relationship exists between interactivity and election results. A manual content

Installation restoration program site investigation. Gulfport Field Training Site, Mississippi Air National Guard Gulfport-Biloxi Regional Airport Gulfport, Mississippi. Volume 2. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-12-01

Site Investigation Report, Volume: 2. A Site Investigation was performed at 3 sites at the Combat Readiness Training Center, Gulfport-Bolixi. The 3 sites investigated are the: Former Fire Training Area (Site 1), the Former JP-4 Bulk Storage Area, Mill Road (Site 2), and the Motor Pool Above-Ground Diesel Fuel Storage Tank Area (Site 3). The findings of this investigation recommended further investigation at the Fire Training Area and the JP-4 Bulk Storage Tank. At Site 3 the levels of contamination did not represent a risk to human health or the environment; therefore, no further action was recommended. Volume two of this report consisted of the following Appendixes: Site Photographs (A), Well Inventory (B), Boring Logs (C), CSL Technical Memorandum (D), Data Review and Validation (E), GPS Memorandum (F), Level C Analytical Data Summary Tables (G), Slug Test (H), Special-Status Species (I), and Representative Species of Less Mobile Fish and Wildlife (J).

Realities of site investigation

International Nuclear Information System (INIS)

Beauheim, R.; Ben Benfahel, M.; Byrum, Ch.; Fedor, F.; Geier, J.; Nys, V.; Schelkes, K.; Selroos, J.O.; Szucs, I.; Whittaker, St.

2007-01-01

During the working session, Working Group C discussed the following questions proposed by the Scientific Programme Committee of AMIGO 2: - Provide a list of concrete examples of limitations and their reasons. In addressing these issues, consider the relation between what you can measure and what you would like to describe. - Can these limitations be handled by defensible uncertainty descriptions? - What has been your experience in predicting properties/responses and then making comparisons with subsequent measurements? How much 'after-fitting' was necessary? Did the exercise contribute to validation? What did it teach you about your abilities to characterise? - What are the realities of transferability of data between sites? What can actually be transferred (data, conceptual models, evaluation procedures) and what could not? - How have the experiences on possibilities and limitations influenced your investigation programme? - How are the limits in what can be achieved factored into safety assessment and engineering? (authors)

Ecological investigations at the Pantex Plant Site, 1992

International Nuclear Information System (INIS)

Cushing, C.E.; Mazaika, R.R.; Phillips, R.C.

1993-09-01

In 1992, Pantex requested that Pacific Northwest Laboratory (PNL) conduct a series of ecological surveys to provide baseline information for designing detailed ecological studies on the various ecosystems present at the Pantex plant site near Amarillo, Texas. To this end, PNL scientist and technicians visited the site at different times to conduct investigations and collect samples: July 6--13: birds, small mammals, general habitat assessment; August 10--14: wetland vegetation, birds, small mammals, Playa invertebrates; and September 7--11: birds, small mammals. This report presents the results of these three surveys

A manual for implementing residual radioactive material guidelines

International Nuclear Information System (INIS)

Gilbert, T.L.; Yu, C.; Yuan, Y.C.; Zielen, A.J.; Jusko, M.J.; Wallo, A. III; Argonne National Lab., IL; Dames and Moore, West Valley, NY; Argonne National Lab., IL; USDOE Assistant Secretary for Nuclear Energy, Washington, DC

1989-06-01

This manual presents information for implementing US Department of Energy (DOE) guidelines for residual radioactive material at sites identified by the Formerly Utilized Sites Remedial Action Program (FUSRAP) and the Surplus Facilities Management Program (SFMP). It describes the analysis and models used to derive site-specific guidelines for allowable residual concentrations of radionuclides in soil and the design and use of the RESRAD computer code for calculating guideline values. It also describes procedures for implementing DOE policy for reducing residual radioactivity to levels that are as low as reasonably achievable. 36 refs., 16 figs, 22 tabs

School Indoor Air Quality Best Management Practices Manual.

Science.gov (United States)

Hall, Richard; Ellis, Richard; Hardin, Tim

This manual, written in response to requirements of the Washington State legislature, focuses on practices which can be undertaken during the siting, design, construction, or renovation of a school, recommends practices to help ensure good indoor air quality during building occupancy, and suggests protocols and useful reference documents for…

Outline of manual on measurement and assessment of doses from external radiation

Energy Technology Data Exchange (ETDEWEB)

Yoshizawa, Michio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Tsujimura, Norio

2001-03-01

The external exposure part in the manual for measurement and assessment of doses from external radiation is described since the part is changed in accordance with the revision of the Law Concerning Prevention from Radiation Hazard due to Radioisotopes, Etc. The manual contains general remarks, control of external exposure and its methods, person monitoring, site monitoring, correction of instruments and storage of records. The 2nd and 3rd chapters are described in details, because which are considerably changed together with appendices concerning the operational quantity for measuring external dose, conversion coefficients, and correlations of 3 mm, 1 cm and 70 {mu}m dose equivalents. Making manuals unique to the individual offices, etc. is recommended in compliance with the above manual.(K.H.)

Oskarshamn site investigation. Monitoring of shallow groundwater chemistry 2009

International Nuclear Information System (INIS)

Ericsson, Ulf

2010-06-01

In 2009 sampling of shallow ground water in water wells in soil has been performed in a regular programme at eight sites within the site investigation area at Oskarshamn. The purpose of the activity is to monitor (long term observation) and characterise the shallow ground water in the site investigation area. Some physical and chemical parameters were measured directly in the field but most parameters were analysed at different laboratories. The ground water sampling activity consisted of one programme, chemical programme class 5 (reduced). The large number of sites and parameters analysed have generated a large amount of data, which will later be used for advanced analysis and modelling. In this report the evaluation aims to give a simple overview of the results and to describe the quality of the data sampled 2009. As an addition radon activity was measured at fourteen sites in the area. Seven of these sites were the same as in the regular programme. The results showed a large variation between the wells. The concentrations of major ions and conductivity ranged from low to high or very high values. The concentration of HCO 3 also varied extensively throughout the investigation area, but since the concentrations were above 60 mg/l in most wells the results indicate a good ground water quality with respect to acidification. The concentration of heavy metals and trace elements also varied. High concentration of Pb in some of the wells indicated pollution. Since Pb had a similar relation to Al as most other elements it was argued that high concentrations of lead probably can be explained by the natural composition of minerals within the site investigation area. The ratio of δ 18 O showed a good relationship with the conductivity. The activity of tritium ( 3 H) was markedly lower in two of the wells. This might be an indication of older groundwater in these wells. The average hydrogen isotope ratio of deuterium (δ 2 H) varied with similar values in most wells. The �

Oskarshamn site investigation. Monitoring of shallow groundwater chemistry 2009

Energy Technology Data Exchange (ETDEWEB)

Ericsson, Ulf (Medins Biologi AB, Moelnlycke (Sweden))

2010-06-15

In 2009 sampling of shallow ground water in water wells in soil has been performed in a regular programme at eight sites within the site investigation area at Oskarshamn. The purpose of the activity is to monitor (long term observation) and characterise the shallow ground water in the site investigation area. Some physical and chemical parameters were measured directly in the field but most parameters were analysed at different laboratories. The ground water sampling activity consisted of one programme, chemical programme class 5 (reduced). The large number of sites and parameters analysed have generated a large amount of data, which will later be used for advanced analysis and modelling. In this report the evaluation aims to give a simple overview of the results and to describe the quality of the data sampled 2009. As an addition radon activity was measured at fourteen sites in the area. Seven of these sites were the same as in the regular programme. The results showed a large variation between the wells. The concentrations of major ions and conductivity ranged from low to high or very high values. The concentration of HCO{sub 3} also varied extensively throughout the investigation area, but since the concentrations were above 60 mg/l in most wells the results indicate a good ground water quality with respect to acidification. The concentration of heavy metals and trace elements also varied. High concentration of Pb in some of the wells indicated pollution. Since Pb had a similar relation to Al as most other elements it was argued that high concentrations of lead probably can be explained by the natural composition of minerals within the site investigation area. The ratio of delta18O showed a good relationship with the conductivity. The activity of tritium (3H) was markedly lower in two of the wells. This might be an indication of older groundwater in these wells. The average hydrogen isotope ratio of deuterium (delta2H) varied with similar values in most wells

Remedial investigation for the chemical plant area of the Weldon Spring Site

International Nuclear Information System (INIS)

1992-11-01

The US Department of Energy (DOE) is responsible for management of the Weldon Spring Site Remedial Action Project (WSSRAP) under its Environmental Restoration and Waste Management Program. Major goals include eliminating potential public and environmental hazards due to site contamination and releasing the property for alternate uses to the maximum extent practicable. The purpose of the remedial investigation described in this report was to determine the extent of contamination associated with the portion of the Weldon Spring site known as the chemical plant and raffinate pit area. The DOE has assumed responsibility for investigating and remediating all on-site soil contamination and off-site soil which is radiologically contaminated as a result of uranium and thorium processing operations. The DOE has also assumed the responsibility for radiologically contaminated groundwater on and off site. The Weldon Spring site remedial investigation also involved the evaluation of the sources, nature and extent, and environmental fate and transport of contaminants to provide a basis for defining the risks that the contaminants may pose to human health and the environment. Data are included in this report to support the screening of remedial technologies and to permit the development and detailed analysis of alternatives for remedial action at the site during the feasibility study process

A Hypothesis-Driven Approach to Site Investigation

Science.gov (United States)

Nowak, W.

2008-12-01

Variability of subsurface formations and the scarcity of data lead to the notion of aquifer parameters as geostatistical random variables. Given an information need and limited resources for field campaigns, site investigation is often put into the context of optimal design. In optimal design, the types, numbers and positions of samples are optimized under case-specific objectives to meet the information needs. Past studies feature optimal data worth (balancing maximum financial profit in an engineering task versus the cost of additional sampling), or aim at a minimum prediction uncertainty of stochastic models for a prescribed investigation budget. Recent studies also account for other sources of uncertainty outside the hydrogeological range, such as uncertain toxicity, ingestion and behavioral parameters of the affected population when predicting the human health risk from groundwater contaminations. The current study looks at optimal site investigation from a new angle. Answering a yes/no question under uncertainty directly requires recasting the original question as a hypothesis test. Otherwise, false confidence in the resulting answer would be pretended. A straightforward example is whether a recent contaminant spill will cause contaminant concentrations in excess of a legal limit at a nearby drinking water well. This question can only be answered down to a specified chance of error, i.e., based on the significance level used in hypothesis tests. Optimal design is placed into the hypothesis-driven context by using the chance of providing a false yes/no answer as new criterion to be minimized. Different configurations apply for one-sided and two-sided hypothesis tests. If a false answer entails financial liability, the hypothesis-driven context can be re-cast in the context of data worth. The remaining difference is that failure is a hard constraint in the data worth context versus a monetary punishment term in the hypothesis-driven context. The basic principle

Remedial Investigation of Hanford Site Releases to the Columbia River - 13603

Energy Technology Data Exchange (ETDEWEB)

Lerch, J.A.; Hulstrom, L.C. [Washington Closure Hanford, LLC, Richland, Washington 99354 (United States); Sands, J.P. [U.S Department of Energy, Richland Operations Office, Richland, Washington 99352 (United States)

2013-07-01

In south-central Washington State, the Columbia River flows through the U.S. Department of Energy Hanford Site. A primary objective of the Hanford Site cleanup mission is protection of the Columbia River, through remediation of contaminated soil and groundwater that resulted from its weapons production mission. Within the Columbia River system, surface water, sediment, and biota samples related to potential Hanford Site hazardous substance releases have been collected since the start of Hanford operations. The impacts from release of Hanford Site radioactive substances to the Columbia River in areas upstream, within, and downstream of the Hanford Site boundary have been previously investigated as mandated by the U.S. Department of Energy requirements under the Atomic Energy Act. The Remedial Investigation Work Plan for Hanford Site Releases to the Columbia River [1] was issued in 2008 to initiate assessment of the impacts under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 [2]. The work plan established a phased approach to characterize contaminants, assess current risks, and determine whether or not there is a need for any cleanup actions. Field investigation activities over a 120-mile stretch of the Columbia River began in October 2008 and were completed in 2010. Sampled media included surface water, pore water, surface and core sediment, island soil, and fish (carp, walleye, whitefish, sucker, small-mouth bass, and sturgeon). Information and sample results from the field investigation were used to characterize current conditions within the Columbia River and assess whether current conditions posed a risk to ecological or human receptors that would merit additional study or response actions under CERCLA. The human health and ecological risk assessments are documented in reports that were published in 2012 [3, 4]. Conclusions from the risk assessment reports are being summarized and integrated with remedial investigation

Surface Environmental Surveillance Procedures Manual, PNL-MA-580, Rev. 5

Energy Technology Data Exchange (ETDEWEB)

Hanf, Robert W.; Poston, Ted M.; Bisping, Lynn E.

2007-07-01

This manual contains the procedures that are used for the collection of routine Surface Environmental Surveillance Project environmental samples and field measurements on and around the Hanford Site. Specific responsibilities for project personnel are also defined.

Uranium tailings sampling manual

International Nuclear Information System (INIS)

Feenstra, S.; Reades, D.W.; Cherry, J.A.; Chambers, D.B.; Case, G.G.; Ibbotson, B.G.

1985-01-01

The purpose of this manual is to describe the requisite sampling procedures for the application of uniform high-quality standards to detailed geotechnical, hydrogeological, geochemical and air quality measurements at Canadian uranium tailings disposal sites. The selection and implementation of applicable sampling procedures for such measurements at uranium tailings disposal sites are complicated by two primary factors. Firstly, the physical and chemical nature of uranium mine tailings and effluent is considerably different from natural soil materials and natural waters. Consequently, many conventional methods for the collection and analysis of natural soils and waters are not directly applicable to tailings. Secondly, there is a wide range in the physical and chemical nature of uranium tailings. The composition of the ore, the milling process, the nature of tailings depositon, and effluent treatment vary considerably and are highly site-specific. Therefore, the definition and implementation of sampling programs for uranium tailings disposal sites require considerable evaluation, and often innovation, to ensure that appropriate sampling and analysis methods are used which provide the flexibility to take into account site-specific considerations. The following chapters describe the objective and scope of a sampling program, preliminary data collection, and the procedures for sampling of tailings solids, surface water and seepage, tailings pore-water, and wind-blown dust and radon

Field manual for stream sediment reconnaissance. Savannah River Laboratory National Uranium Resource Evaluation Program

International Nuclear Information System (INIS)

Ferguson, R.B.; Price, V.; Baucom, E.I.

1976-07-01

A manual is presented that is intended to direct and coordinate field operations, site selection, stream sediment sample collection, water sample collection, and information codes for the Savannah River Laboratory (SRL) contribution to the National Uranium Resource Evaluation (NURE) program. The manual provides public relations information for field sampling teams as well as technical direction

Verification study on technology for site investigation for geological disposal. Confirmation of the applicability of survey methods through establishing site descriptive models in accordance with stepwise investigation approach

International Nuclear Information System (INIS)

Kondo, Hirofumi; Suzuki, Koichi; Hasegawa, Takuma; Hamada, Takaomi; Yoshimura, Kimitaka

2014-01-01

The Yokosuka Demonstration and Validation Project, which uses the Yokosuka Central Research Institute of Electric Power Industry (CRIEPI) site, a Neogene sedimentary and coastal environment, has been conducted since the 2006 fiscal year as a cooperative research project between NUMO (Nuclear Waste Management Organization of Japan) and CRIEPI. The objectives of this project were to examine and refine the basic methodology of the investigation and assessment in accordance with the conditions of geological environment at each stage of investigations from the surface (Preliminary Investigation and the first half of Detailed Investigation conducted by NUMO) for high level radioactive waste geological disposal. Within investigation technologies at these early stages, a borehole survey is an important means of directly obtaining various properties of the deep geological environment. On the other hand, surface geophysical prospecting data provide information about the geological and resistivity structures at depth for planning borehole surveys. During the 2006-2009 fiscal years, a series of on-site surveys and tests, including borehole surveys of YDP-1 (depth: 350 m) and YDP-2 (depth: 500 m), were conducted in this test site. Furthermore, seismic surveys (including seismic reflection method) and electromagnetic surveys (including magnetotelluric method) were conducted within the expanded CRIEPI site in the 2010 fiscal year to obtain information about the geological structure, and the resistivity structure reflecting the distribution of the salt water/fresh water boundary, respectively, to a depth of over several hundred meters. The validity of existing survey and testing methods for stepwise investigations (from surface to borehole surveys) for obtaining properties of the geological environment (in various conditions relating to differences in the properties of the Miura and the Hayama Groups at this site) was confirmed through establishing site descriptive models based on

The Weatherization Assistant User's Manual (Version 8.9)

Energy Technology Data Exchange (ETDEWEB)

Gettings, Michael B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Malhotra, Mini [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ternes, Mark P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-01-01

The Weatherization Assistant is a Windows-based energy audit software tool that was developed by Oak Ridge National Laboratory (ORNL) to help states and their local weatherization agencies implement the U.S. Department of Energy (DOE) Weatherization Assistance Program. The Weatherization Assistant is an umbrella program for two individual energy audits or measure selection programs: the National Energy Audit Tool (NEAT) for site-built single-family homes and the Manufactured Home Energy Audit (MHEA) for mobile homes. The Weatherization Assistant User's Manual documents the operation of the user interface for Version 8.9 of the software. This includes how to install and setup the software, navigate through the program, and initiate an energy audit. All of the user interface forms associated with the software and the data fields on these forms are described in detail. The manual is intended to be a training manual for new users of the Weatherization Assistant and as a reference manual for experienced users.

Measurement of mesothelioma on thoracic CT scans: A comparison of manual and computer-assisted techniques

International Nuclear Information System (INIS)

Armato, Samuel G. III; Oxnard, Geoffrey R.; MacMahon, Heber; Vogelzang, Nicholas J.; Kindler, Hedy L.; Kocherginsky, Masha; Starkey, Adam

2004-01-01

Our purpose in this study was to evaluate the variability of manual mesothelioma tumor thickness measurements in computed tomography (CT) scans and to assess the relative performance of six computerized measurement algorithms. The CT scans of 22 patients with malignant pleural mesothelioma were collected. In each scan, an initial observer identified up to three sites in each of three CT sections at which tumor thickness measurements were to be made. At each site, five observers manually measured tumor thickness through a computer interface. Three observers repeated these measurements during three separate sessions. Inter- and intra-observer variability in the manual measurement of tumor thickness was assessed. Six automated measurement algorithms were developed based on the geometric relationship between a specified measurement site and the automatically extracted lung regions. Computer-generated measurements were compared with manual measurements. The tumor thickness measurements of different observers were highly correlated (r≥0.99); however, the 95% limits of agreement for relative inter-observer difference spanned a range of 30%. Tumor thickness measurements generated by the computer algorithms also correlated highly with the average of observer measurements (r≥0.93). We have developed computerized techniques for the measurement of mesothelioma tumor thickness in CT scans. These techniques achieved varying levels of agreement with measurements made by human observers

General Employee Radiological Training and Radiological Worker Training: Program management manual

International Nuclear Information System (INIS)

1992-10-01

This manual defines and describes the DOE General Employee Radiological Training (GERT) and Radiological Worker I and II (RW I and II) Training programs. It includes material development requirements, standards and policies, and program administration. This manual applies to General Employee Radiological Training and Radiological Worker Training at all DOE contractor sites. The training materials of both GERT and RW I and II training reflect the requirements identified in the DOE Radiological Control Manual and DOE Order 5480.11. The training programs represent the minimum requirement for the standardized core materials. Each contractor shall implement the program in its entirety and may augment the standardized core materials to increase the general employee and radiological worker level of competency

Investigation of tritium in groundwater at Site 300

International Nuclear Information System (INIS)

Buddemeier, R.W.

1985-01-01

In 1984, landfill monitoring wells at Site 300, a Lawrence Livermore National Laboratory (LLNL) explosive test site, revealed the presence of groundwater contaminated with tritium. These tritium levels were in excess of the State of California drinking water standard. A major investigation was initiated that included a search of records concerning tritium use, disposal, and previous analyses, and a survey of tritium levels in soil, vegetation, and water in contaminated and potentially contaminated areas. Over 50 boreholes were drilled for this investigation to characterize the local hydrogeology and tritium distributions, and a network of soil moisture and groundwater monitoring points was installed. This report presents the work completed through the end of September 1985: the records search; records for drilling completed as part of this study; characterization of the geology, hydrology, and tritium distributions in the contaminated area; and an initial assessment of the probable tritium sources, pathways, and migration rates. 19 refs

Investigation of tritium in groundwater at Site 300

Energy Technology Data Exchange (ETDEWEB)

Buddemeier, R.W.

1985-12-30

In 1984, landfill monitoring wells at Site 300, a Lawrence Livermore National Laboratory (LLNL) explosive test site, revealed the presence of groundwater contaminated with tritium. These tritium levels were in excess of the State of California drinking water standard. A major investigation was initiated that included a search of records concerning tritium use, disposal, and previous analyses, and a survey of tritium levels in soil, vegetation, and water in contaminated and potentially contaminated areas. Over 50 boreholes were drilled for this investigation to characterize the local hydrogeology and tritium distributions, and a network of soil moisture and groundwater monitoring points was installed. This report presents the work completed through the end of September 1985: the records search; records for drilling completed as part of this study; characterization of the geology, hydrology, and tritium distributions in the contaminated area; and an initial assessment of the probable tritium sources, pathways, and migration rates. 19 refs.

Site characterization investigations at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Ketelle, R.H.

1985-01-01

The geologic and geohydrologic characterization and assessment techniques currently used at ORNL are integrated into a systematic approach. The investigations are multi-faceted, and involve investigators with a variety of expertise. Characterization studies are designed to obtain the data requirements of pathways analysis and facility design in addition to the detailed site description. The approach effectively minimizes the redundancy and lack of coordination which often arise when the study is broken down into totally independent tasks. The geologic environment of the Oak Ridge Reservation is one of structural and stratigraphic complexity which requires a comprehensive and systematic approach to characterize. Recent characterization studies have included state-of-the-science techniques in the areas of unsaturated zone testing, geochemical tests to determine attenuation properties of soils, and numerical analyses of site performance. The results of these studies and analyses are changing the technology of shallow land burial by indicating that chemically stable waste forms are required to limit radionuclide migration to acceptable levels. 11 refs., 1 tab

Site safety plan for Lawrence Livermore National Laboratory CERCLA investigations at site 300. Revision 2

Energy Technology Data Exchange (ETDEWEB)

Kilmer, J.

1997-08-01

Various Department of Energy Orders incorporate by reference, health and safety regulations promulgated by the Occupational Safety and Health Administration (OSHA). One of the OSHA regulations, 29 CFR 1910.120, Hazardous Waste Operations and Emergency Response, requires that site safety plans are written for activities such as those covered by work plans for Site 300 environmental investigations. Based upon available data, this Site Safety Plan (Plan) for environmental restoration has been prepared specifically for the Lawrence Livermore National Laboratory Site 300, located approximately 15 miles east of Livermore, California. As additional facts, monitoring data, or analytical data on hazards are provided, this Plan may need to be modified. It is the responsibility of the Environmental Restoration Program and Division (ERD) Site Safety Officer (SSO), with the assistance of Hazards Control, to evaluate data which may impact health and safety during these activities and to modify the Plan as appropriate. This Plan is not `cast-in-concrete.` The SSO shall have the authority, with the concurrence of Hazards Control, to institute any change to maintain health and safety protection for workers at Site 300.

Site characterization and validation - hydrochemical investigations. Stage 3

International Nuclear Information System (INIS)

Laaksoharju, M.

1990-02-01

The objective for the Stage 3 hydrochemical investigations was to classify groundwater and to determine the different flow paths within the investigated SCV-site by using water analyses from the C and D boreholes. The water was divided into three classes shallow (A), mixed (B) and deep groundwater (C) based on Cl and HCO 3 concentration. The local geohydrological situation in the SCV-site can be divided into a disturbed situation and an undisturbed situation. Opening of the boreholes and smapling causes a disturbance of hydrochemical conditions. Three water types were found in the important water conductors, the GB and the GH zones. Shallow water (A-type) is flowing downwards while deep groundwater (C-type) is flowing upwards driven by the pumping of the mine. Where the two water types meet a zone of approximately 30 m thickness with mixed (B-type) water is formed. The flow situation is revealed by the geohydrological measurements. At undisturbed conditions shallow water (A-type) is flowing down in the investigated zones. The B and C water types are then found at a deeper level than during disturbed conditions. A regional model can be constructed based on the described chemical and geohydrological investigations. Shallow water from the top and deep groundwater from below are drawn towards the mine by the pumping. Where these waters meet mixed water is formed. (orig./HP)

Sandia National Laboratories, California Environmental Management System program manual.

Energy Technology Data Exchange (ETDEWEB)

Larsen, Barbara L.

2013-04-01

The Sandia National Laboratories, California (SNL/CA) Environmental Management System (EMS) Program Manual documents the elements of the site EMS Program. The SNL/CA EMS Program conforms to the International Standard on Environmental Management Systems, ISO 14001:2004 and Department of Energy (DOE) Order 436.1.

Sandia National Laboratories, California Environmental Management System program manual

Energy Technology Data Exchange (ETDEWEB)

Larsen, Barbara L.

2014-04-01

The Sandia National Laboratories, California (SNL/CA) Environmental Management System (EMS) Program Manual documents the elements of the site EMS Program. The SNL/CA EMS Program conforms to the International Standard on Environmental Management Systems, ISO 14001:2004 and Department of Energy (DOE) Order 436.1.

Manual for conducting radiological surveys in support of license termination

International Nuclear Information System (INIS)

Berger, J.D.

1992-06-01

This document describes a process for conducting radiological surveys during decommissioning, to demonstrate that residual radioactive material satisfies criteria established by the U.S. Nuclear Regulatory Commission (NRC) for termination of a license. The Manual describes procedures for design and conduct of surveys in a manner which will provide a high degree of assurance that NRC guidelines and conditions have been satisfied. The Manual also describes methods for documenting the survey findings in a final report to the NRC. This Manual updates information contained in NUREG/CR-2082, Monitoring for Compliance with Decommissioning Termination Survey Criteria, (ORNL 1981). It incorporates statistical approaches to survey design and data interpretation used by the Environmental Protection Agency for evaluation of hazardous materials sites under Superfund (CERCLA). Quality assurance is emphasized throughout. (author)

Geochemical investigation of UMTRAP designated site at Salt Lake City, Utah

International Nuclear Information System (INIS)

Markos, G.; Bush, K.J.

1983-09-01

This report is the result of a geochemical investigation of the former uranium mill and tailings site at Salt Lake City, Utah. This is one in a series of site specific geochemical investigations performed on the inactive uranium mill tailings included in the Uranium Mill Tailings Remedial Action Project. The objectives of the investigation are to characterize the geochemistry, to determine the contaminant distribution resulting from the former milling activities and tailings, and to infer chemical pathways and transport mechanisms from the contaminant distribution. The results will be used to model contaminant migration and to develop criteria for long-term containment media such as a cover system which is impermeable to contaminant migration. This report assumes a familiarity with the hydrologic conditions of the site and the geochemical concepts underlying the investigation. The results reported are based on a one-time sampling of waters and solid material from the background, the area adjacent to the site, and the site. The solid samples were water extracted to remove easily soluble salts and acid extracted to remove carbonates and hydroxides. The water extracts and solid samples were anlyzed for the major and trace elements. The report includes the methods of sampling, sample processing, analysis, and data interpretation. Four major conclusions are: (1) sediments in the ditches and creeks adjacent to the site contain tailings, however, the waters were generally not contaminated; (2) tailings are mixed with the soils within a meter below the tailings in some locations, however, water-soluble contaminants decrease to below background levels within 30 cm below the tailings; (3) there has not been significant acid seepage into the soils below the tailings; and (4) salt crusts on the tailings contain trace elements, with the elements that form chloride complexes having the greatest accumulation

Prioritization to limit sampling and drilling in site investigations

International Nuclear Information System (INIS)

Burton, J.C.

1992-01-01

One of the major goals of the Environmental Research Division of Argonne National Laboratory is to develop and provide governmental agencies with technically sound, cost-effective frameworks for environmental site characterization and remedial programs. An example of the development of such a framework for preremedial site characterization is presented in this paper. Specifically, this paper presents portions of an expanded site investigation program developed for landfills suspected of containing hazardous waste. The work was sponsored by the New Mexico State Office of the US Department of Interior's Bureau of Land Management (BLM). The emphasis of the BLM program was on identifying initial characterization procedures that would decrease the need for sampling and drilling on a random grid

Investigation of nonlinear dynamic soil property at the Savannah River Site

International Nuclear Information System (INIS)

Lee, R.C.

2000-01-01

This document summarizes laboratory dynamic soil testing investigations conducted by the University of Texas at Austin (UTA) for the Savannah River Site (SRS) (Stokoe et al., 1995a, Stokoe et al., 1995b, Sponseller and Stokoe, 1995). The purpose of the investigation is to provide an evaluation of past testing results in the context of new test data and the development of consistent site wide models of material strain dependencies based upon geologic formation, depth, and relevant index properties

Development of the Coordination between Posture and Manual Control

Science.gov (United States)

Haddad, Jeffrey M.; Claxton, Laura J.; Keen, Rachel; Berthier, Neil E.; Riccio, Gary E.; Hamill, Joseph; Van Emmerik, Richard E. A.

2012-01-01

Studies have suggested that proper postural control is essential for the development of reaching. However, little research has examined the development of the coordination between posture and manual control throughout childhood. We investigated the coordination between posture and manual control in children (7- and 10-year-olds) and adults during…

Field Manual of Wildlife Diseases

Science.gov (United States)

Franson, J. Christian; Friend, Milton; Gibbs, Samantha E.J.; Wild, Margaret A.

2015-01-01

Welcome to a new version of the “Field Manual of Wildlife Diseases.” Unlike the previous printed versions of this publication, this new version is being developed as a “living“ electronic publication. Content will periodically be added and (or) updated as warranted, and it will always be reviewed by scientific experts (“peer reviewed”) before it is released. Thus, this publication will never be completed, and readers should download revised versions of specific chapters, glossaries, and the appendixes whenever they visit the publication Web site.

An investigation of site diversity and comparison with ITU-R recommendations

Science.gov (United States)

Callaghan, S. A.; Boyes, B.; Couchman, A.; Waight, J.; Walden, C. J.; Ventouras, S.

2008-08-01

Earth-space radio systems operating at frequencies of 10 GHz and above are badly attenuated by rain, cloud, and atmospheric gases. As the frequencies of operational systems increase, it becomes increasingly uneconomic to compensate for the effects of fading through the use of a fixed fade margin, hence the implementation of fade mitigation techniques (FMT). The spatial and temporal variation of rain provides the justification for the use of site diversity as an FMT. Site diversity employs two or more ground stations receiving the same satellite signal with a separation distance such that the sites encounter intense rainfall at different times, and switching to the site experiencing the least fading improves system performance considerably. Measurements of the 20.7 GHz beacon carried as part of the Global Broadcast Service (GBS) payload on the U.S. Department of Defense satellite UFO-9 have been made at three sites: two are located in the South of England (˜8 km apart), and the third receiver was located in Scotland. These beacon measurements have produced long term attenuation exceedance and site diversity gain and improvement statistics. This attenuation time series data can simulate the performance of an Earth-space system using site diversity, indicating the optimum method of implementing this FMT. In this paper, unbalanced site diversity is investigated, as this is a more likely scenario than the balanced site diversity modeled by the ITU-R recommendations. This paper also investigates the implementation of site diversity from a commercial context, including cost-benefit analysis and technical feasibility.

SNL/CA Environmental Management System Program Manual.

Energy Technology Data Exchange (ETDEWEB)

Larsen, Barbara L.

2007-04-01

The Sandia National Laboratories, California (SNL/CA) Environmental Management System (EMS) Program Manual documents the elements of the site EMS Program. The SNL/CA EMS Program conforms to the International Standard on Environmental Management Systems, ISO 14001:2004. Elements of the ISO standard overlap with those of Department of Energy (DOE) Order 450.1, thus SNL/CA's EMS program also meets the DOE requirements.

Manual Therapy

OpenAIRE

Hakgüder, Aral; Kokino, Siranuş

2002-01-01

Manual therapy has been used in the treatment of pain and dysfunction of spinal and peripheral joints for more than a hundred years. Manual medicine includes manipulation, mobilization, and postisometric relaxation techniques. The aim of manual therapy is to enhance restricted movement caused by blockage of joints keeping postural balance, restore function and maintain optimal body mechanics. Anatomic, biomechanical, and neurophysiological evaluations of the leucomotor system is essential for...

Design/CPN. A Reference Manual

DEFF Research Database (Denmark)

Jensen et. al, Kurt

/CPN WWW pages. To speed up the access to the Design/CPN manuals we recommend to keep a local copy - which may be shared by all users in your organisation. In this way you do not need to go via our WWW server each time you need to look in a manual. For some of the largest manuals, we also supply files......Note: The manuals are available as PDF files . There are two sets of manuals - one for the Unix platform and another for the Mac platform. Each set of manual consists of: Tutorial (for the Design/CPN editor and simulator) Reference Manual (for the Design/CPN editor and simulator) Programmer......'s Manual (with Design/OA functions and Charts) Occurrence Graph Manual (integrated tutorial and reference manual) OE/OS Graph Manual (integrated tutorial and reference manual) Other Manuals (e.g. a short overview of CPN ML).   The Tutorial, Reference Manual and Programmer's Manual are made for Design...

Factors associated with high physical exertion during manual lifting

DEFF Research Database (Denmark)

Andersen, Lars L.; Sundstrup, Emil; Brandt, Mikkel

2018-01-01

BACKGROUND: High physical exertion during work is a risk factor for back pain and long-term sickness absence. OBJECTIVE: To investigate which factors are associated with physical exertion during manual lifting. METHODS: From 14 workplaces across Denmark, 200 blue-collar workers reported perceived...... physical exertion (Borg-CR10) during manual lifting from floor to table height of 5, 10, 20 and 30 kg at the beginning and end of the working day. The workers also responded to a questionnaire and went through testing of isometric back muscle strength. Associations were modelled using logistic regression...... during manual lifting in blue-collar workers. These factors should be considered when planning work with manual lifting for individual workers....

Caltrans : construction manual

Science.gov (United States)

2009-08-01

Caltrans intends this manual as a resource for all personnel engaged in contract administration. The manual establishes policies and procedures for the construction phase of Caltrans projects. However, this manual is not a contract document. It impos...

Corrective Action Investigation Plan for Corrective Action Unit 139: Waste Disposal Sites, Nevada Test Site, Nevada, Rev. No.: 0

Energy Technology Data Exchange (ETDEWEB)

Grant Evenson

2006-04-01

Corrective Action Unit (CAU) 139 is located in Areas 3, 4, 6, and 9 of the Nevada Test Site, which is 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 139 is comprised of the seven corrective action sites (CASs) listed below: (1) 03-35-01, Burn Pit; (2) 04-08-02, Waste Disposal Site; (3) 04-99-01, Contaminated Surface Debris; (4) 06-19-02, Waste Disposal Site/Burn Pit; (5) 06-19-03, Waste Disposal Trenches; (6) 09-23-01, Area 9 Gravel Gertie; and (7) 09-34-01, Underground Detection Station. These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives with the exception of CASs 09-23-01 and 09-34-01. Regarding these two CASs, CAS 09-23-01 is a gravel gertie where a zero-yield test was conducted with all contamination confined to below ground within the area of the structure, and CAS 09-34-01 is an underground detection station where no contaminants are present. Additional information will be obtained by conducting a corrective action investigation (CAI) before evaluating corrective action alternatives and selecting the appropriate corrective action for the other five CASs where information is insufficient. The results of the field investigation will support a defensible evaluation of viable corrective action alternatives that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed on January 4, 2006, by representatives of the Nevada Division of Environmental Protection; U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office; Stoller-Navarro Joint Venture; and Bechtel Nevada. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 139.

The working mechanism of manual therapy in participants with chronic tension-type headache

NARCIS (Netherlands)

Castien, R.F.; Blankenstein, A.H.; van der Windt, D.; Heijmans, M.W.; Dekker, J.

2013-01-01

STUDY DESIGN: Prospective longitudinal study.OBJECTIVE: To explore the working mechanism of manual therapy, we investigated whether 3 cervical spine variables were mediators of the effect of manual therapy on headache frequency.BACKGROUND: Manual therapy has been shown to reduce headache frequency

Site characterization and validation - Borehole radar investigations stage 3

International Nuclear Information System (INIS)

Sandberg, E.; Olsson, O.; Falk, L.

1989-11-01

The borehole radar investigation program Stage 3 of the SCV-site has comprised single hole reflection measurements with centre frequencies of 22 and 60 MHz. Single hole reflection measurement with both omni-directional and directional antennas have been performed in the boreholes C1, C2, C3 and the D-holes. Crosshole tomographic measurements as well as cross- hole reflection measurement have been made between the bore- holes C1-C2, W1-C1 and W1-C2. The range obtained in the single hole reflection measurements was approximately 100 m for the lower frequency and about 60-70 m for the centre frequency 60 MHz. In the crosshole measurements transmitter-receiver separations from 20 to 120 m have been used. The Stage 3 radar investigations have essentially confirmed the three dimensional description of the structures at the SCV-site. The conceptual model of the site which was produced based on the Stage 1 data included three major zones, two minor zones and a circular feature. The major features are considered to be the most significant at the site and are all observed in the Stage 3 boreholes close to their predicted locations. The circular feature has also been found in two of the additional tomograms at the predicted location. The results indicate that the zones are not homogeneous but rather that they are highly irregular containing parts of considerably increased fracturing and parts where their contrast to the background rock is quite small. The zones appear to be approximately planar at least at the scale of the site. At a smaller scale the zones can appear quite irregular

LBA-ECO TG-07 Trace Gas Fluxes, Undisturbed and Logged Sites, Para, Brazil: 2000-2002

Science.gov (United States)

M.M. Keller; R.K. Varner; J.D. Dias; H.S. Silva; P.M. Crill; Jr. de Oliveira; G.P. Asner

2009-01-01

Trace gas fluxes of carbon dioxide, methane, nitrous oxide, and nitric oxide were measured manually at undisturbed and logged forest sites in the Tapajos National Forest, near Santarem, Para, Brazil. Manual measurements were made approximately weekly at both the undisturbed and logged sites. Fluxes from clay and sand soils were completed at the undisturbed sites....

75 FR 55965 - Adoption of Updated EDGAR Filer Manual

Science.gov (United States)

2010-09-15

... the timely acceptance and processing of filings made in electronic format.\\3\\ Filers may consult the... electronic format copies on the Commission's Web site; the address for the Filer Manual is http://www.sec.gov... for notice and comment is not required under the Administrative Procedure Act (APA).\\6\\ It follows...

Review of Investigations on Site Selection for Nuclear Power Plants in Croatia

Energy Technology Data Exchange (ETDEWEB)

Malbasa, N [Ekonerg, Zagreb (Croatia)

2008-07-01

A review of site investigation for nuclear facilities in the Republic of Croatia that had been performed from 1964, when investigation started for the first nuclear power plant, to 1994 when the activities were stopped, is presented therein. Brief results of the main investigation were presented including the Tanja site on the Danube upstream of Vukovar. It is the best of all the investigated locations for nuclear power plant in Croatia. The review of results for site selection of low and intermediate level of radioactive waste disposal is also given. The position of nuclear power plants in the strategic documents of the Republic of Croatia was analysed. It is concluded that the status of nuclear facilities in the main strategic documents must be improved because the energy future in Croatia - as almost in all European countries - could hardly be successful without any further development of nuclear energy.(author)

Review of Investigations on Site Selection for Nuclear Power Plants in Croatia

International Nuclear Information System (INIS)

Malbasa, N.

2008-01-01

A review of site investigation for nuclear facilities in the Republic of Croatia that had been performed from 1964, when investigation started for the first nuclear power plant, to 1994 when the activities were stopped, is presented therein. Brief results of the main investigation were presented including the Tanja site on the Danube upstream of Vukovar. It is the best of all the investigated locations for nuclear power plant in Croatia. The review of results for site selection of low and intermediate level of radioactive waste disposal is also given. The position of nuclear power plants in the strategic documents of the Republic of Croatia was analysed. It is concluded that the status of nuclear facilities in the main strategic documents must be improved because the energy future in Croatia - as almost in all European countries - could hardly be successful without any further development of nuclear energy.(author)

Preliminary safety evaluation for the Laxemar subarea. Based on data and site descriptions after the initial site investigation stage

Energy Technology Data Exchange (ETDEWEB)

Andersson, Johan [JA Streamflow AB, Aelvsjoe (Sweden)

2006-03-15

The main objectives of this Preliminary Safety Evaluation (PSE) of the Laxemar subarea have been to determine, with limited efforts, whether the feasibility study's judgement of the suitability of the candidate area with respect to long-term safety holds up in the light of the actual site investigation data; to provide feedback to continued site investigations and site-specific repository design and to identify site-specific scenarios and geoscientific issues for further analyses. The PSE focuses on comparing the attained knowledge of the sites with the suitability criteria as set out by SKB in 2000. These criteria both concern properties of the site judged to be necessary for safety and engineering (requirements) and properties judged to be beneficial (preferences). The findings are then evaluated in order to provide feedback to continued investigations and design work. The PSE does not aim at comparing sites and does not assess compliance with safety and radiation protection criteria. The latter is eventually done in coming Safety Assessments. This preliminary safety evaluation shows that, according to existing data, the Laxemar subarea meets all safety requirements. The evaluation also shows that the Laxemar subarea meets most of the safety preferences, but for some aspects of the site description further reduction of the uncertainties would enhance the safety case. Despite the stated concerns, there is no reason, from a safety point of view, not to continue the Site Investigations at the Laxemar subarea. There are uncertainties to resolve and the safety would eventually need to be verified through a proper safety assessment. Only some of the uncertainties noted in the Site Descriptive Model have safety implications and need further resolution for this reason. Furthermore, uncertainties may need resolving for other reasons, such as giving an adequate assurance of site understanding or assisting in optimising design. Notably, there are questions about the

Preliminary safety evaluation for the Laxemar subarea. Based on data and site descriptions after the initial site investigation stage

International Nuclear Information System (INIS)

Andersson, Johan

2006-03-01

The main objectives of this Preliminary Safety Evaluation (PSE) of the Laxemar subarea have been to determine, with limited efforts, whether the feasibility study's judgement of the suitability of the candidate area with respect to long-term safety holds up in the light of the actual site investigation data; to provide feedback to continued site investigations and site-specific repository design and to identify site-specific scenarios and geoscientific issues for further analyses. The PSE focuses on comparing the attained knowledge of the sites with the suitability criteria as set out by SKB in 2000. These criteria both concern properties of the site judged to be necessary for safety and engineering (requirements) and properties judged to be beneficial (preferences). The findings are then evaluated in order to provide feedback to continued investigations and design work. The PSE does not aim at comparing sites and does not assess compliance with safety and radiation protection criteria. The latter is eventually done in coming Safety Assessments. This preliminary safety evaluation shows that, according to existing data, the Laxemar subarea meets all safety requirements. The evaluation also shows that the Laxemar subarea meets most of the safety preferences, but for some aspects of the site description further reduction of the uncertainties would enhance the safety case. Despite the stated concerns, there is no reason, from a safety point of view, not to continue the Site Investigations at the Laxemar subarea. There are uncertainties to resolve and the safety would eventually need to be verified through a proper safety assessment. Only some of the uncertainties noted in the Site Descriptive Model have safety implications and need further resolution for this reason. Furthermore, uncertainties may need resolving for other reasons, such as giving an adequate assurance of site understanding or assisting in optimising design. Notably, there are questions about the

Transferring manual ultrasonic inspection procedures - results of a pilot study

International Nuclear Information System (INIS)

Anderson, M.; Taylor, T.; Kadenko, I.

2002-01-01

Results of a manual ultrasonic pilot study for NDE specialists at RBMK nuclear reactor sites are presented. Probabilities of detection and false calls, using two different grading criteria, are estimated. Analyses of performance parameters lead to conclusions regarding attributes for improved test discrimination capabilities. (orig.)

The development of practice manual for LSC based on job analysis in radiation measurement and analysis

International Nuclear Information System (INIS)

Shin, W H; Park, T J

2017-01-01

Radiation technology is closely related to the industrial growth and the creation of employment in Korea. The techniques as radiation or/and radioactivity measurement, and the practical skills achieving a higher level analysis are required. In this study, practice manual for liquid scintillation counter were developed by job analysis. Raw data applied in job analysis are collected by on/off line survey by 420 workers employed in KOREA. Importance-priority analysis was performed to make duties and competency unit that consists of knowledge, skills as each task. Refined data was reviewed by expert who experienced actual duties on site. Classification was conducted by focus group interview to deduct duties and competency unit. From the radiation devices in measurement and analysis, liquid scintillation counter was preferentially selected because of the high demands for training. Investigation of build-up status to liquid scintillation counter in KOREA was conducted. Then technical specification and operating procedure of 2 main devices were analyzed and integrated by practice manual. Duties and competency unit were applied to integrated materials respectively. To validate effectiveness, test curriculum was designed by the advanced course to workers who engaged in radiation measurement and analysis. The developed manual is structured to take advantage of test training. This manual will be a practical handbook that can improve the knowledge, skills of radiation workers in Korea. (paper)

The development of practice manual for LSC based on job analysis in radiation measurement and analysis

Science.gov (United States)

Shin, W. H.; Park, T. J.

2017-06-01

Radiation technology is closely related to the industrial growth and the creation of employment in Korea. The techniques as radiation or/and radioactivity measurement, and the practical skills achieving a higher level analysis are required. In this study, practice manual for liquid scintillation counter were developed by job analysis. Raw data applied in job analysis are collected by on/off line survey by 420 workers employed in KOREA. Importance-priority analysis was performed to make duties and competency unit that consists of knowledge, skills as each task. Refined data was reviewed by expert who experienced actual duties on site. Classification was conducted by focus group interview to deduct duties and competency unit. From the radiation devices in measurement and analysis, liquid scintillation counter was preferentially selected because of the high demands for training. Investigation of build-up status to liquid scintillation counter in KOREA was conducted. Then technical specification and operating procedure of 2 main devices were analyzed and integrated by practice manual. Duties and competency unit were applied to integrated materials respectively. To validate effectiveness, test curriculum was designed by the advanced course to workers who engaged in radiation measurement and analysis. The developed manual is structured to take advantage of test training. This manual will be a practical handbook that can improve the knowledge, skills of radiation workers in Korea.

Corrective Action Investigation Plan for Corrective Action Unit 104: Area 7 Yucca Flat Atmospheric Test Sites, Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Patrick Matthews

2011-08-01

CAU 104 comprises the 15 CASs listed below: (1) 07-23-03, Atmospheric Test Site T-7C; (2) 07-23-04, Atmospheric Test Site T7-1; (3) 07-23-05, Atmospheric Test Site; (4) 07-23-06, Atmospheric Test Site T7-5a; (5) 07-23-07, Atmospheric Test Site - Dog (T-S); (6) 07-23-08, Atmospheric Test Site - Baker (T-S); (7) 07-23-09, Atmospheric Test Site - Charlie (T-S); (8) 07-23-10, Atmospheric Test Site - Dixie; (9) 07-23-11, Atmospheric Test Site - Dixie; (10) 07-23-12, Atmospheric Test Site - Charlie (Bus); (11) 07-23-13, Atmospheric Test Site - Baker (Buster); (12) 07-23-14, Atmospheric Test Site - Ruth; (13) 07-23-15, Atmospheric Test Site T7-4; (14) 07-23-16, Atmospheric Test Site B7-b; (15) 07-23-17, Atmospheric Test Site - Climax These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed on April 28, 2011, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 104. The releases at CAU 104 consist of surface-deposited radionuclides from 30 atmospheric nuclear tests. The presence and nature of contamination at CAU 104 will be evaluated based on information collected from a field investigation. Radiological contamination will be evaluated based on a comparison

Site investigations for repositories for solid radioactive wastes in deep continental geological formations

International Nuclear Information System (INIS)

1982-01-01

This report reviews the earth-science investigations and associated scientific studies that may be needed to select a repository site and confirm that its characteristics are such that it will provide a safe confinement for solidified high-level and alpha-bearing and certain other solid radioactive wastes. Site investigations, as used in this report, cover earth sciences and associated safety analyses. Other site-investigation activities are identified but not otherwise considered here. The repositories under consideration are those consisting of mined cavities in deep continental rocks for accepting wastes in the solid and packaged form. The term deep as used in this report is used solely to emphasize the distinction between the repositories discussed in this report and those for shallow-ground disposal. In general, depths under consideration here are greater than 200 metres. The term continental refers to those geological formations that occur either beneath present-day land masses and adjoining islands or beneath the shallow seas. One of the objectives of site investigations is to collect the site-specific data necessary for the different evaluations, such as modelling required to assess the long-term safety of an underground repository

Site investigations for repositories for solid radioactive wastes in deep continental geological formations

Energy Technology Data Exchange (ETDEWEB)

1982-01-01

This report reviews the earth-science investigations and associated scientific studies that may be needed to select a repository site and confirm that its characteristics are such that it will provide a safe confinement for solidified high-level and alpha-bearing and certain other solid radioactive wastes. Site investigations, as used in this report, cover earth sciences and associated safety analyses. Other site-investigation activities are identified but not otherwise considered here. The repositories under consideration are those consisting of mined cavities in deep continental rocks for accepting wastes in the solid and packaged form. The term deep as used in this report is used solely to emphasize the distinction between the repositories discussed in this report and those for shallow-ground disposal. In general, depths under consideration here are greater than 200 metres. The term continental refers to those geological formations that occur either beneath present-day land masses and adjoining islands or beneath the shallow seas. One of the objectives of site investigations is to collect the site-specific data necessary for the different evaluations, such as modelling required to assess the long-term safety of an underground repository.

MX Siting Investigation. MX System Siting Summary Report. General Introduction. Volume I. Part I.

Science.gov (United States)

1982-01-18

LINEAR CONNECT CRN MIX SITING INVESTIGATION DEPARTMENT OF THE AIR FORCE VOUTS USING VALLEY CLUSTERING CONCEPT IN IOC, BMO/AFRCE- wIX VOUTS IN DRY LAKE...species, such as the jackrabbit, may be the center of important food webs , and a decrease in its numbers may greatly affect many other species. The

CSTEM User Manual

Science.gov (United States)

Hartle, M.; McKnight, R. L.

2000-01-01

This manual is a combination of a user manual, theory manual, and programmer manual. The reader is assumed to have some previous exposure to the finite element method. This manual is written with the idea that the CSTEM (Coupled Structural Thermal Electromagnetic-Computer Code) user needs to have a basic understanding of what the code is actually doing in order to properly use the code. For that reason, the underlying theory and methods used in the code are described to a basic level of detail. The manual gives an overview of the CSTEM code: how the code came into existence, a basic description of what the code does, and the order in which it happens (a flowchart). Appendices provide a listing and very brief description of every file used by the CSTEM code, including the type of file it is, what routine regularly accesses the file, and what routine opens the file, as well as special features included in CSTEM.

Contaminated site investigation using nuclear technique: a case study of temporary transformer storage sites in Ghana

International Nuclear Information System (INIS)

Sanu, J. K.

2013-07-01

Recent introduction of man-made toxic chemicals, and the massive relocation of natural materials to different environmental compartment like soil, ground water and atmosphere, has resulted in severe pressure on the self- cleansing capacity of recipient ecosystems. Various accomulated pollutants and contaminants such as polychlorinated biphenyls (PCBs) are of much concern relative to both human and ecosystemm exposure and potential health impact. PCBs which are resistant to degradation and bioremediation accumulated in different niches of the biosphere. This significantly affects the ecological balances and cause adverse health effect on both human and the environment. Temporal transformer storage sites at four locations in Ghana (Tema, Temale, Bolgatanga and Wa) were investigated for PCB contamination using nuclear techniques. Analysis of soil samples from four temporal transformer storage sites revealed that the soil samples from Tema, Tamale, Bolgatanga and Wa were generally sandy with pH and EC ranging between 6.24 - 7.29 and 44.60 - 188.30 respectively. The PCB levels detected in the soil samples from the various locations varied considerably with mean ranging between 7.69 and 51.92 mg/kg. The highest mean PCB level was recorded at the Tema temporal transformer storage site (51.92 mg/kg), whilst the least mean level of 7.69 mg/kg was recorded at Wa storage site. At Tamale the individual levels range between 3.57 mg/kg and 38.70 mg/kg while at Bolgatanga it was 6.85 - 16.30 mg/kg and Wa, 6.08 - 14.70mg/kg. About 9% of soil samples from temporal transformer storage sites analysed had total PCBs concentrations above the 25mg/kg and 33 mg/kg level recommended by the Canadian Council of Ministers of environment (CCME) and EPA Ghana respectively for the protection of environment and human health. Generally, the Levels of PCBs in soil samples were found to decrease with increasing depth at all the temporal transformer storage sites. Results obtained using the EPA's L

Final Phase II report : QuickSite(R) investigation, Everest, Kansas.

Energy Technology Data Exchange (ETDEWEB)

LaFreniere, L. M. (Environmental Research)

2003-11-01

this reason, the CCC/USDA is conducting an environmental site investigation to determine the source(s) and extent of the carbon tetrachloride contamination at Everest and to assess whether the contamination requires remedial action. The investigation at Everest is being performed by the Environmental Research Division of Argonne National Laboratory. Argonne is a nonprofit, multidisciplinary research center operated by the University of Chicago for the U.S. Department of Energy (DOE). The CCC/USDA has entered into an interagency agreement with DOE, under which Argonne provides technical assistance to the CCC/USDA with environmental site characterization and remediation at its former grain storage facilities. At these facilities, Argonne is applying its QuickSite{reg_sign} environmental site characterization methodology. This methodology has been applied successfully at a number of former CCC/USDA facilities in Kansas and Nebraska and has been adopted by the American Society for Testing and Materials (ASTM 1998) as standard practice for environmental site characterization. Phase I of the QuickSite{reg_sign} investigation examined the key geologic, hydrogeologic, and hydrogeochemical relationships that define potential contaminant migration pathways at Everest (Argonne 2001). Phase II of the QuickSite{reg_sign} investigation at Everest was undertaken with the primary goal of delineating and improving understanding of the distribution of carbon tetrachloride contamination in groundwater at this site and the potential source area(s) that might have contributed to this contamination. To address this goal, four specific technical objectives were developed to guide the Phase II field studies. Sampling of near-surface soils at the former Everest CCC/USDA facility that was originally planned for Phase I had to be postponed until October 2000 because of access restrictions. Viable vegetation was not available for sampling then. This period is termed the first session of Phase II

Bedrock Hydrogeology-Site investigation SFR

International Nuclear Information System (INIS)

Oehman, Johan; Bockgaard, Niclas; Follin, Sven

2012-06-01

The Swedish Nuclear Fuel and Waste Management Company (SKB) has conducted site investigations for a planned extension of the existing final repository for short-lived radioactive waste (SFR). This report presents an integrated analysis and interpretation of the historic data from the existing SFR (1980 - 1986), as well as, from the recent investigations for the planned extension of SFR (2008 - 2009). The primary objective is to establish a conceptual hydrogeological model of the bedrock for safety assessment and design analyses. Analyses and interpretations of all (old and new) hydraulic data are analysed with regard to the recently developed geological deformation zone model of the SFR model domain (Curtis et al. 2011). The methodology used by Curtis et al. (2011) has focussed on magnetic anomalies and deformation zone intercepts with ground surface greater than 300 m. In the hydrogeological modelling, however, it has been considered important to also explore the occurrence and characteristics of shallow horizontal to sub-horizontal structures (sheet joints) inside the SFR model domain. Such structures are of considerable importance for the hydrogeology in the uppermost c. 150 m of bedrock in SDM-Site Forsmark; hence the term Shallow Bedrock Aquifer was used to emphasise their hydraulic significance. In this study, the acronym SBA-structure is used for horizontal structures identified in the hydrogeological modelling. In addition to the predominantly steeply dipping geological deformation zones, eight so-called SBA-structures are modelled deterministically in the hydrogeological model. The SBA-structures are envisaged as hydraulically heterogeneous and composed of clusters of minor gently dipping to horizontal fractures rather than extensive single features. A type of structures that is partly included in the definition of the SBA-structures is the Unresolved Possible Deformations Zone (Unresolved PDZ) intercepts identified by Curtis et al. (2011). The Unresolved

Bedrock Hydrogeology - Site investigation SFR

Energy Technology Data Exchange (ETDEWEB)

Oehman, Johan [Geosigma AB, Stockholm (Sweden); Bockgaard, Niclas [Golder Assoes AB, Stockholm (Sweden); Follin, Sven [SF GeoLogic AB, Taeby (Sweden)

2012-06-15

The Swedish Nuclear Fuel and Waste Management Company (SKB) has conducted site investigations for a planned extension of the existing final repository for short-lived radioactive waste (SFR). This report presents an integrated analysis and interpretation of the historic data from the existing SFR (1980 - 1986), as well as, from the recent investigations for the planned extension of SFR (2008 - 2009). The primary objective is to establish a conceptual hydrogeological model of the bedrock for safety assessment and design analyses. Analyses and interpretations of all (old and new) hydraulic data are analysed with regard to the recently developed geological deformation zone model of the SFR model domain (Curtis et al. 2011). The methodology used by Curtis et al. (2011) has focussed on magnetic anomalies and deformation zone intercepts with ground surface greater than 300 m. In the hydrogeological modelling, however, it has been considered important to also explore the occurrence and characteristics of shallow horizontal to sub-horizontal structures (sheet joints) inside the SFR model domain. Such structures are of considerable importance for the hydrogeology in the uppermost c. 150 m of bedrock in SDM-Site Forsmark; hence the term Shallow Bedrock Aquifer was used to emphasise their hydraulic significance. In this study, the acronym SBA-structure is used for horizontal structures identified in the hydrogeological modelling. In addition to the predominantly steeply dipping geological deformation zones, eight so-called SBA-structures are modelled deterministically in the hydrogeological model. The SBA-structures are envisaged as hydraulically heterogeneous and composed of clusters of minor gently dipping to horizontal fractures rather than extensive single features. A type of structures that is partly included in the definition of the SBA-structures is the Unresolved Possible Deformations Zone (Unresolved PDZ) intercepts identified by Curtis et al. (2011). The Unresolved

Google The Missing Manual

CERN Document Server

Milstein, Sarah; Dornfest, Rael; MacDonald, Matthew

2008-01-01

Google.com is one of the most popular sites on the Internet and is used around the world by millions of people every day. Sure, you know how to "Google it" when you're searching for something--anything!--on the Web. It's plenty fast and easy to use. But did you know how much more you could achieve with the world's best search engine by clicking beyond the "Google Search" button? While you can interface with Google in 97 languages and glean results in 35, you can't find any kind of instruction manual from Google. Lucky for you, our fully updated and greatly expanded second edition to the best

I need to know! Timely accessing of perioperative user manuals.

Science.gov (United States)

Landreneau, Raphael

2010-12-01

Ready access to equipment or product information is essential for the safe operation of the many items that a perioperative nurse is asked to use, troubleshoot, or maintain. One institution's solution for making manufacturer information available in the practice setting was to create a facility intranet site dedicated to OR equipment manuals. This site provides information access to perioperative nurses and support staff members and, ultimately, helps improve patient care. Published by Elsevier Inc. All rights reserved.

Site Investigation for Detection of KIJANG Reactor Core Center

Energy Technology Data Exchange (ETDEWEB)

Kwon, Tae-Hyun; Kim, Jun Yeon; Kim, Jeeyoung [KAERI, Daejeon (Korea, Republic of)

2015-05-15

It was planned for the end of March 2017 and extended to April 2018 according to the government budget adjustment. The KJRR project is intended for filling the self-sufficiency of RI demand including Mo-99, increasing the NTD capacity and developing technologies related to the research reactor. In project, site investigation is the first activity that defines seismologic and related geologic aspects of the site. Site investigation was carried out from Oct. 2012 to Jan. 2014 and this study is intended to describe detail procedures in locating the reactor core center. The location of the reactor core center was determined by collectively reviewing not only geological information but also information from architects engineering. EL 50m was selected as ground level by levering construction cost. Four recommended locations (R-1a - R-1d) are displayed for the reactor core center. R-1a was found optimal in consideration of medium rock contour, portion of medium rock covering reactor buildings, construction cost, physical protection and electrical resistivity. It is noted that engineering properties of the medium rock is TCR/RQD 100/53, elastic modulus 7,710 - 8,720MPa, permeability coefficient 2.92E-06cm/s, and S-wave velocity 1,380m/s, sound for foundations of reactor buildings.

Regional Test Center Operations Manual

Energy Technology Data Exchange (ETDEWEB)

Stein, Joshua [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Burnham, Laurie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Christian Birk [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-07-01

The U.S. DOE Regional Test Center for Solar Technologies program was established to validate photovoltaic (PV) technologies installed in a range of different climates. The program is funded by the Energy Department's SunShot Initiative. The initiative seeks to make solar energy cost competitive with other forms of electricity by the end of the decade. Sandia National Laboratory currently manages four different sites across the country. The National Renewable Energy Laboratory manages a fifth site in Colorado. The entire PV portfolio currently includes 20 industry partners and almost 500 kW of installed systems. The program follows a defined process that outlines tasks, milestones, agreements, and deliverables. The process is broken out into four main parts: 1) planning and design, 2) installation, 3) operations, and 4) decommissioning. This operations manual defines the various elements of each part.

INES: The International Nuclear Event Scale user's manual

International Nuclear Information System (INIS)

1992-09-01

The revised and extended addition of the International Nuclear Event Scale is presented. The manual is comprised of four parts. Part 1 contains a summary of the basis of the scale and of the procedure to be used for rating events. Part 2 contains the detailed guidance required to rate events in terms of off-site and on-site impact. These two parts are applicable to all nuclear facilities. Parts 3 and 4 contain the detailed guidance required to rate events in terms of defence in depth for reactors and other facilities, respectively. 5 figs, 2 tabs

EMSL Operations Manual

Energy Technology Data Exchange (ETDEWEB)

Foster, Nancy S.

2009-06-18

This manual is a general resource tool to assist EMSL users and Laboratory staff within EMSL locate official policy, practice and subject matter experts. It is not intended to replace or amend any formal Battelle policy or practice. Users of this manual should rely only on Battelle’s Standard Based Management System (SBMS) for official policy. No contractual commitment or right of any kind is created by this manual. Battelle management reserves the right to alter, change, or delete any information contained within this manual without prior notice.

EMSL Operations Manual

Energy Technology Data Exchange (ETDEWEB)

Foster, Nancy S.

2009-03-25

This manual is a general resource tool to assist EMSL users and Laboratory staff within EMSL locate official policy, practice and subject matter experts. It is not intended to replace or amend any formal Battelle policy or practice. Users of this manual should rely only on Battelle’s Standard Based Management System (SBMS) for official policy. No contractual commitment or right of any kind is created by this manual. Battelle management reserves the right to alter, change, or delete any information contained within this manual without prior notice.

AIMSsim Version 2.3.4 - User Manual

National Research Council Canada - National Science Library

Schoenborn, Oliver; Lachance, Patrick; Bahramifarid, Nima

2008-01-01

This user manual provides an overview of the software functionality developed to support the empirical investigation of a simulated user interface for an Advanced Integrated Multi-sensor Surveillance (AIMS) system...

Gingival abrasion and recession in manual and oscillating-rotating power brush users.

Science.gov (United States)

Rosema, N A M; Adam, R; Grender, J M; Van der Sluijs, E; Supranoto, S C; Van der Weijden, G A

2014-11-01

To assess gingival recession (GR) in manual and power toothbrush users and evaluate the relationship between GR and gingival abrasion scores (GA). This was an observational (cross-sectional), single-centre, examiner-blind study involving a single-brushing exercise, with 181 young adult participants: 90 manual brush users and 91 oscillating-rotating power brush users. Participants were assessed for GR and GA as primary response variables. Secondary response variables were the level of gingival inflammation, plaque score reduction and brushing duration. Pearson correlation was used to describe the relationship between number of recession sites and number of abrasions. Prebrushing (baseline) and post-brushing GA and plaque scores were assessed and differences analysed using paired tests. Two-sample t-test was used to analyse group differences; ancova was used for analyses of post-brushing changes with baseline as covariate. Overall, 97.8% of the study population had at least one site of ≥1 mm of gingival recession. For the manual group, this percentage was 98.9%, and for the power group, this percentage was 96.7% (P = 0.621). Post-brushing, the power group showed a significantly smaller GA increase than the manual group (P = 0.004); however, there was no significant correlation between number of recession sites and number of abrasions for either group (P ≥ 0.327). Little gingival recession was observed in either toothbrush user group; the observed GR levels were comparable. Lower post-brushing gingival abrasion levels were seen in the power group. There was no correlation between gingival abrasion as a result of brushing and the observed gingival recession following use of either toothbrush. © 2014 The Authors International Journal of Dental Hygiene Published by John Wiley & Sons Ltd.

Preliminary site description Laxemar stage 2.1. Feedback for completion of the site investigation including input from safety assessment and repository engineering

International Nuclear Information System (INIS)

2006-09-01

The Laxemar subarea is the focus for the complete site investigations in the Simpevarp area. The south and southwestern parts of the subarea (the so-called 'focused area') have been designated for focused studies during the remainder of the site investigations. This area, some 5.3 square kilometres in size, is characterised on the surface by an arc shaped body of quartz monzodiorite gently dipping to the north, flanked in the north and south by Aevroe granite. The current report documents work conducted during stage 2.1 of the site-descriptive modelling of the Laxemar subarea. The primary objective of the work performed is to provide feedback to the site investigations at Laxemar to ensure that adequate and timely data and information are obtained during the remaining investigation stage. The work has been conducted in cooperation with the site investigation team at Laxemar and representatives from safety assessment and repository engineering. The principal aim of this joint effort has been to safeguard that adequate data are collected that resolve the remaining issues/uncertainties which are of importance for repository layout and long-term safety. The proposed additional works presented in this report should be regarded as recommended additions and/or modifications in relation to the CSI programme published early 2006. The overall conclusion of the discipline-wise review of critical issues is that the CSI programme overall satisfies the demands to resolve the remaining uncertainties. This is interpreted to be partly a result of the close interaction between the site modelling team, site investigation team and the repository engineering teams, which has been in operation since early 2005. In summary, the performed interpretations and modelling have overall confirmed the version 1.2 results. The exception being Hydrogeology where the new Laxemar 2.1 borehole data suggest more favourable conditions in the south and west parts of the focused area compared with the

Site-specific investigations of aquifer thermal energy storage for space and process cooling

International Nuclear Information System (INIS)

Brown, D.R.

1991-01-01

This paper reports on the Pacific Northwest Laboratory (PNL) that has completed three preliminary site-specific feasibility studies that investigated aquifer thermal energy storage (ATES) for reducing space and process cooling costs. Chilled water stored in an ATES system could be used to meet all or part of the process and/or space cooling loads at the three facilities investigated. Seasonal or diurnal chill ATES systems could be significantly less expensive than a conventional electrically-driven, load-following chiller system at one of the three sites, depending on the cooling water loop return temperature and presumed future electricity escalation rate. For the other two sites investigated, a chill ATES system would be economically competitive with conventional chillers if onsite aquifer characteristics were improved. Well flow rates at one of the sites were adequate, but the expected thermal recovery efficiency was too low. The reverse of this situation was found at the other site, where the thermal recovery efficiency was expected to be adequate, but well flow rates were too low

Manual Performance Deterioration in the Cold

NARCIS (Netherlands)

Daanen, H.A.M.

2009-01-01

Manual performance during military operations in cold and windy climates is severely hampered by decreased dexterity, but valid dexterity decrease predictors based on climatic factors are scarce. Therefore, this study investigated the decrease in finger dexterity for nine combinations of ambient

Applying Minimal Manual Principles for Documentation of Graphical User Interfaces.

Science.gov (United States)

Nowaczyk, Ronald H.; James, E. Christopher

1993-01-01

Investigates the need to include computer screens in documentation for software using a graphical user interface. Describes the uses and purposes of "minimal manuals" and their principles. Studies student reaction to their use of one of three on-screen manuals: screens, icon, and button. Finds some benefit for including icon and button…

Fixed site neutralization model programmer's manual. Volume II

International Nuclear Information System (INIS)

Engi, D.; Chapman, L.D.; Judnick, W.; Blum, R.; Broegler, L.; Lenz, J.; Weinthraub, A.; Ballard, D.

1979-12-01

This report relates to protection of nuclear materials at nuclear facilities. This volume presents the source listings for the Fixed Site Neutralization Model and its supporting modules, the Plex Preprocessor and the Data Preprocessor

INTRA/Mod3.2. Manual and code description. Volume 2 - User's manual

International Nuclear Information System (INIS)

Andersson, Jenny; Edlund, O.; Hermann, J.; Johansson, Lise-Lotte

1999-01-01

The INTRA Manual consists of two volumes. Volume I of the manual is a thorough description of the code INTRA, the physical modelling of INTRA and the ruling numerics, and volume II, the User's Manual is an input description. This document, the User's Manual, Volume II, contains a detailed description of how to use INTRA, how to set up an input file, how to run INTRA and also post-processing

U.S. Department of Energy's site screening, site selection, and initial characterization for storage of CO2 in deep geological formations

Science.gov (United States)

Rodosta, T.D.; Litynski, J.T.; Plasynski, S.I.; Hickman, S.; Frailey, S.; Myer, L.

2011-01-01

The U.S. Department of Energy (DOE) is the lead Federal agency for the development and deployment of carbon sequestration technologies. As part of its mission to facilitate technology transfer and develop guidelines from lessons learned, DOE is developing a series of best practice manuals (BPMs) for carbon capture and storage (CCS). The "Site Screening, Site Selection, and Initial Characterization for Storage of CO2 in Deep Geological Formations" BPM is a compilation of best practices and includes flowchart diagrams illustrating the general decision making process for Site Screening, Site Selection, and Initial Characterization. The BPM integrates the knowledge gained from various programmatic efforts, with particular emphasis on the Characterization Phase through pilot-scale CO2 injection testing of the Validation Phase of the Regional Carbon Sequestration Partnership (RCSP) Initiative. Key geologic and surface elements that suitable candidate storage sites should possess are identified, along with example Site Screening, Site Selection, and Initial Characterization protocols for large-scale geologic storage projects located across diverse geologic and regional settings. This manual has been written as a working document, establishing a framework and methodology for proper site selection for CO2 geologic storage. This will be useful for future CO2 emitters, transporters, and storage providers. It will also be of use in informing local, regional, state, and national governmental agencies of best practices in proper sequestration site selection. Furthermore, it will educate the inquisitive general public on options and processes for geologic CO2 storage. In addition to providing best practices, the manual presents a geologic storage resource and capacity classification system. The system provides a "standard" to communicate storage and capacity estimates, uncertainty and project development risk, data guidelines and analyses for adequate site characterization, and

AIMSsim Version 2.2.1, User Manual

National Research Council Canada - National Science Library

Schoenborn, Oliver

2007-01-01

This user manual provides an overview of how to use the software developed to support the empirical investigation of a simulated user interface for an Advanced Integrated Multi sensor Surveillance (AIMS) system...

Structures manual

Science.gov (United States)

2001-01-01

This manual was written as a guide for use by design personnel in the Vermont Agency of Transportation Structures Section. This manual covers the design responsibilities of the Section. It does not cover other functions that are a part of the Structu...

Ciencias 2. Manual do Professor (Science Teacher's Manual).

Science.gov (United States)

Raposo, Lucilia

This is the teacher's manual for Ciencias 2, the second in a series of elementary science textbooks for Portuguese-speaking students. The student textbook contains 10 chapters and 57 activities. The teacher's manual presents an explanation of the educational goals and the organization of the content, Topics included are environment, the human,…

Egyptian Mythological Manuals

DEFF Research Database (Denmark)

Jørgensen, Jens Kristoffer Blach

From the hands of Greek mythographers a great number of myths have survived along with philosophical discussions of their meaning and relevance for the Greeks. It is little known that something similar existed in ancient Egypt where temple libraries and archives held scholarly literature used...... by the native priesthood, much of which has only been published in recent years. As part of this corpus of texts, the ancient Egyptian mythological manuals offer a unique perspective on how the Egyptian priesthood structured and interpreted Egyptian myths. The thesis looks at the different interpretative...... techniques used in the Tebtunis Mythological Manual (Second century CE) and the Mythological Manual of the Delta (Sixth century BCE) and the place of these manuals within the larger corpus of priestly scholarly literature from ancient Egypt. To organize the wealth of local myths the manuals use model...

Corrective Action Investigation Plan for Corrective Action Unit 568: Area 3 Plutonium Dispersion Sites Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Matthews, Patrick

2014-01-01

CAU 568 is a grouping of sites where there has been a suspected release of contamination associated with nuclear testing. This document describes the planned investigation of CAU 568, which comprises the following corrective action sites (CASs): • 03-23-17, S-3I Contamination Area • 03-23-19, T-3U Contamination Area • 03-23-20, Otero Contamination Area • 03-23-22, Platypus Contamination Area • 03-23-23, San Juan Contamination Area • 03-23-26, Shrew/Wolverine Contamination Area These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the investigation report.

FRMAC Operations Manual

Energy Technology Data Exchange (ETDEWEB)

Frandsen, K.

2010-05-01

In the event of a major radiological incident, the Federal Radiological Monitoring and Assessment Center (FRMAC) will coordinate the federal agencies that have various statutory responsibilities. The FRMAC is responsible for coordinating all environmental radiological monitoring, sampling, and assessment activities for the response. This manual describes the FRMAC’s response activities in a radiological incident. It also outlines how FRMAC fits in the National Incident Management System (NIMS) under the National Response Framework (NRF) and describes the federal assets and subsequent operational activities which provide federal radiological monitoring and assessment of the affected areas. In the event of a potential or existing major radiological incident, the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) is responsible for establishing and managing the FRMAC during the initial phases.

Integrated account of method, site selection and programme prior to the site investigation phase[Planning for a Swedish repository for spent nuclear fuels

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-12-01

In order to dispose of the spent nuclear fuel in a safe manner, SKB plans to site a deep repository and an encapsulation plant with associated canister fabrication and transportation system. After an integrated evaluation of feasibility studies and other material, SKB will proceed with investigations of the rock and studies regarding establishment of the deep disposal system in the municipality of Oskarshamn or in Northern Uppland. The plans also include further study of the prospects for a deep repository in the municipality of Nykoeping. In the municipality of Oskarshamn, SKB plans further studies of a siting of the deep repository at Simpevarp. There SKB wants to initiate site investigations with test drilling. For the encapsulation plant, SKB wants to continue studying a siting at CLAB. In Northern Uppland, SKB plans to study two siting alternatives for the deep repository. One is Forsmark in the municipality of Oesthammar, where SKB wants to initiate a site investigation with test drilling. The other is Tierp north of Skutskaer, where SKB intends to start test drilling in an area north of Tierp. First, however, a suitable drilling area with possible transport solutions needs to be defined. This alternative requires the participation of the municipalities of both Tierp and Aelvkarleby. A siting of the encapsulation plant in Northern Uppland will also be studied. For the municipality of Nykoeping, SKB plans to conduct a new safety assessment for the Fjaellveden area, based on data from previous investigations as well as additional studies of how a deep repository could be arranged. SKB will thereby gather data from yet another geographic and geological region beyond those that are prioritized. No test drilling is planned in Nykoeping. The goal of the site investigation phase is to obtain all permits needed to build the planned facilities. It will take an estimated 7 - 8 years to assemble the requisite supporting material, carry out consultations, compile siting

Investigation of the site selection examples adopted local participation. The site selection processes in Belgium, UK and Switzerland

International Nuclear Information System (INIS)

Kageyama, Hitoshi; Suzuki, Shinji; Hirose, Ikuro; Yoshioka, Tatsuji

2014-06-01

In late years, local participation policies are being adopted in foreign countries at site selection for the disposal of the radioactive waste. We performed documents investigation about the examples of the site selection processes of Belgium, the U.K., and Switzerland to establish the site selection policy in Japan. In Belgium, after the failure of the site selection for the disposal of short-lived low and intermediate level radioactive waste (LILW) in an early stage, the idea of the local partnership (LP) was developed and three independent LPs were established between the implementing body and each municipality. About 7 years later, one site was decided as the disposal site in the cabinet meeting of the federal government. In the U.K., after the failure of the site selection for the rock characterization facility, the government policy was changed and the consultation process comprised of six phases was started. Though the process had been carried out for over 4 years since one combined partnership was established between the implementing body and the municipalities involved, they had to withdraw from the consulting process because a county council had not accepted that the process would step forward to the 4th phase. In Switzerland, the implementing body selected one site for LILW disposal at an early stage, but the project was denied by the referendum in the Canton having jurisdiction over the site area. After that the Federal Parliament established new Nuclear Energy Act and Nuclear Energy Ordinance precluding the veto of Canton. Now the site selection project is being carried out according to the process comprised of three phases with local participation policy. Reviewing the merits and demerits of each example through this investigation, we confirmed if we are to adopt local participation policy in our country in future, further prudent study would be necessary, considering current and future social conditions in Japan. (author)

Preparation of site emergency preparedness plans for nuclear installations

International Nuclear Information System (INIS)

1999-10-01

Safety of public, occupational workers and the protection of environment should be assured while activities for economic and social progress are pursued. These activities include the establishment and utilisation of nuclear facilities and use of radioactive sources. This safety guidelines is issued as a lead document to facilitate preparation of specific site manuals by the responsible organisation for emergency response plans at each site to ensure their preparedness to meet any eventuality due to site emergency in order to mitigate its consequences on the health and safety of site personnel. It takes cognizance of an earlier AERB publications on the subject: Safety manual on site emergency plan on nuclear installations. AERB/SM/NISD-1, 1986 and also takes into consideration the urgent need for promoting public awareness and drawing up revised emergency response plans, which has come about in a significant manner after the accidents at Chernobyl and Bhopal

Revision of the protective action guides manual for nuclear incidents

International Nuclear Information System (INIS)

DeCair, S.; MacKinney, J.

2007-01-01

EPA's 1992 Manual of Protective Action Guides and Protective Actions for Nuclear Incidents, referred to as the PAG Manual, is a radiological emergency planning and response tool for emergency management officials at the Federal, state, tribal, and local levels. A Protective Action Guide is defined as, the projected dose to reference man, or other defined individual, from a release of radioactive material at which a specific protective action to reduce or avoid that dose is recommended'. The updated version of the PAG Manual accomplishes these key objectives: applying the existing 1992 protective action guides and protective actions to new radiological and nuclear scenarios of concern; updating the dosimetry basis; lowering the recommended dose for administration of stable iodine; providing new guidance concerning consumption of drinking water during or after a radiological emergency; updating the dosimetry basis for all derived levels, and, adding guidance for dealing with long-term site restoration following a major radiological release. (author)

Preliminary site description Laxemar stage 2.1. Feedback for completion of the site investigation including input from safety assessment and repository engineering

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-09-15

The Laxemar subarea is the focus for the complete site investigations in the Simpevarp area. The south and southwestern parts of the subarea (the so-called 'focused area') have been designated for focused studies during the remainder of the site investigations. This area, some 5.3 square kilometres in size, is characterised on the surface by an arc shaped body of quartz monzodiorite gently dipping to the north, flanked in the north and south by Aevroe granite. The current report documents work conducted during stage 2.1 of the site-descriptive modelling of the Laxemar subarea. The primary objective of the work performed is to provide feedback to the site investigations at Laxemar to ensure that adequate and timely data and information are obtained during the remaining investigation stage. The work has been conducted in cooperation with the site investigation team at Laxemar and representatives from safety assessment and repository engineering. The principal aim of this joint effort has been to safeguard that adequate data are collected that resolve the remaining issues/uncertainties which are of importance for repository layout and long-term safety. The proposed additional works presented in this report should be regarded as recommended additions and/or modifications in relation to the CSI programme published early 2006. The overall conclusion of the discipline-wise review of critical issues is that the CSI programme overall satisfies the demands to resolve the remaining uncertainties. This is interpreted to be partly a result of the close interaction between the site modelling team, site investigation team and the repository engineering teams, which has been in operation since early 2005. In summary, the performed interpretations and modelling have overall confirmed the version 1.2 results. The exception being Hydrogeology where the new Laxemar 2.1 borehole data suggest more favourable conditions in the south and west parts of the focused area compared

Geophysical investigation, Salmon Site, Lamar County, Mississippi

International Nuclear Information System (INIS)

1995-02-01

Geophysical surveys were conducted in 1992 and 1993 on 21 sites at the Salmon Site (SS) located in Lamar County, Mississippi. The studies are part of the Remedial Investigation/Feasibility Study (RI/FS) being conducted by IT Corporation for the U.S. Department of Energy (DOE). During the 1960s, two nuclear devices and two chemical tests were detonated 826 meters (in) (2710 feet [ft]) below the ground surface in the salt dome underlying the SS. These tests were part of the Vela Uniform Program conducted to improve the United States capability to detect, identify, and locate underground nuclear detonations. The RI/FS is being conducted to determine if any contamination is migrating from the underground shot cavity in the salt dome and if there is any residual contamination in the near surface mud and debris disposal pits used during the testing activities. The objective of the surface geophysical surveys was to locate buried debris, disposal pits, and abandoned mud pits that may be present at the site. This information will then be used to identify the locations for test pits, cone penetrometer tests, and drill hole/monitor well installation. The disposal pits were used during the operation of the test site in the 1960s. Vertical magnetic gradient (magnetic gradient), electromagnetic (EM) conductivity, and ground-penetrating radar (GPR) surveys were used to accomplish these objectives. A description of the equipment used and a theoretical discussion of the geophysical methods are presented Appendix A. Because of the large number of figures relative to the number of pages of text, the geophysical grid-location maps, the contour maps of the magnetic-gradient data, the contour maps of the EM conductivity data, and the GPR traverse location maps are located in Appendix B, Tabs I through 22. In addition, selected GPR records are located in Appendix C

Comparison of automated and manual shielding block fabrication

International Nuclear Information System (INIS)

Weeks, K.J.; Fraass, B.A.; McShan, D.L.; Hardybala, S.S.; Hargreaves, E.A.; Lichter, A.S.

1989-01-01

This work reports the results of a study comparing computer controlled and manual shielding block cutting. The general problems inherent in automated block cutting have been identified and minimized. A system whose accuracy is sufficient for clinical applications has been developed. The relative accuracy of our automated system versus experienced technician controlled cutting was investigated. In general, it is found that automated cutting is somewhat faster and more accurate than manual cutting for very large fields, but that the reverse is true for most smaller fields. The relative cost effectiveness of automated cutting is dependent on the percentage of computer designed blocks which are generated in the clinical setting. At the present time, the traditional manual method is still favored

Geochemical investigation of UMTRAP designated site at Grand Junction, Colorado

International Nuclear Information System (INIS)

Markos, G.; Bush, K.J.

1983-09-01

This report is the result of a geochemical investigation of the former uranium mill and tailings site at Grand Junction, Colorado. The objectives of the investigation are to characterize the geochemistry, to determine the contaminant distribution resulting from the former milling activities and tailings, and to infer chemical pathways and transport mechanisms from the contaminant distribution. The results should be used to model contaminant migration and to develop criteria for long-term containment media, such as a cover system which is impermeable to contaminant migration. This report assumes a familiarity with the hydrologic conditions of the site and the geochemical concepts underlying the investigation. The results reported are based on a sampling of waters in two seasons and solid material from the background, the area adjacent to the site, and the site. The solid samples were water extracted to remove easily soluble salts and acid extracted to remove carbonates and hydroxides. The water extracts and solid samples were analyzed for the major and trace elements. A limited number of samples were analyzed for radiological components. The report includes the methods of sampling, sample processing, analysis, and data interpretation. Four major conclusions are: (1) trace element concentrations in shallow subsurface waters adjacent to the tailings temporally vary up to an order of magnitude; (2) the riverbank soils and borehole waters are contaminated with uranium, radium, and trace elements from discharge of tailings solids and solutions during the active time of the mill; however, the movement of contaminants toward the Colorado River does not appear to be significant; (3) the Colorado River adjacent to the tailings is not contaminated; and (4) trace metals have accumulated at both the tailings/cover and tailings/soil interface because of precipitation reactions caused by chemical differences between the two materials

Field manual for identifying and preserving high-water mark data

Science.gov (United States)

Feaster, Toby D.; Koenig, Todd A.

2017-09-26

This field manual provides general guidance for identifying and collecting high-water marks and is meant to be used by field personnel as a quick reference. The field manual describes purposes for collecting and documenting high-water marks along with the most common types of high-water marks. The manual provides a list of suggested field equipment, describes rules of thumb and best practices for finding high-water marks, and describes the importance of evaluating each high-water mark and assigning a numeric uncertainty value as part of the flagging process. The manual also includes an appendix of photographs of a variety of high-water marks obtained from various U.S. Geological Survey field investigations along with general comments about the logic for the assigned uncertainty values.

Animal investigation program 1974 annual report: Nevada Test Site and vicinity

International Nuclear Information System (INIS)

Smith, D.D.; Giles, K.R.; Bernhardt, D.E.; Brown, K.R.

1977-06-01

Data are presented from the radioanalysis of tissues collected from cattle, deer, desert bighorn sheep, and other wildlife that resided on or near the Nevada Test Site during 1974. Routine activities and special investigations of the Animal Investigation Program are also discussed. Other than the naturally occurring potassium-40, gamma-emitting radionuclides were detected infrequently. For example, cesium-137 was found only in the muscle tissues from 3 of the 12 Nevada Test Site cattle sampled during 1974. Tritium concentrations in the tissues from most of the animals sampled are at background levels. Animals from the experimental farm tended to have slightly higher concentrations than those sampled at other locations on the Nevada Test Site. Strontium-90 levels in bones from deer, desert bighorn sheep, and cattle were slightly lower than those reported for the preceding year. A graph depicts the average levels found in the bones of the three species from 1956 through 1974

Corrective Action Investigation Plan for Corrective Action Unit 105: Area 2 Yucca Flat Atmospheric Test Sites Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Patrick Matthews

2012-09-01

Corrective Action Unit (CAU) 105 is located in Area 2 of the Nevada National Security Site, which is approximately 65 miles northwest of Las Vegas, Nevada. CAU 105 is a geographical grouping of sites where there has been a suspected release of contamination associated with atmospheric nuclear testing. This document describes the planned investigation of CAU 105, which comprises the following corrective action sites (CASs): • 02-23-04, Atmospheric Test Site - Whitney • 02-23-05, Atmospheric Test Site T-2A • 02-23-06, Atmospheric Test Site T-2B • 02-23-08, Atmospheric Test Site T-2 • 02-23-09, Atmospheric Test Site - Turk These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed on April 30, 2012, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 105. The site investigation process will also be conducted in accordance with the Soils Activity Quality Assurance Plan, which establishes requirements, technical planning, and general quality practices to be applied to this activity. The potential contamination sources associated with all CAU 105 CASs are from atmospheric nuclear testing activities. The presence and nature of contamination at CAU

Corrective Action Investigation Plan for Corrective Action Unit 570: Area 9 Yucca Flat Atmospheric Test Sites Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Patrick Matthews

2012-08-01

CAU 570 comprises the following six corrective action sites (CASs): • 02-23-07, Atmospheric Test Site - Tesla • 09-23-10, Atmospheric Test Site T-9 • 09-23-11, Atmospheric Test Site S-9G • 09-23-14, Atmospheric Test Site - Rushmore • 09-23-15, Eagle Contamination Area • 09-99-01, Atmospheric Test Site B-9A These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed on April 30, 2012, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 570. The site investigation process will also be conducted in accordance with the Soils Activity Quality Assurance Plan, which establishes requirements, technical planning, and general quality practices to be applied to this activity. The presence and nature of contamination at CAU 570 will be evaluated based on information collected from a field investigation. Radiological contamination will be evaluated based on a comparison of the total effective dose at sample locations to the dose-based final action level. The total effective dose will be calculated as the total of separate estimates of internal and external dose. Results from the analysis of soil samples will be used to calculate internal radiological

Hanford External Dosimetry Technical Basis Manual PNL-MA-842

Energy Technology Data Exchange (ETDEWEB)

Rathbone, Bruce A.

2010-04-01

The Hanford External Dosimetry Technical Basis Manual PNL-MA-842 documents the design and implementation of the external dosimetry system used at the U.S. Department of Energy (DOE) Hanford site. The manual describes the dosimeter design, processing protocols, dose calculation methodology, radiation fields encountered, dosimeter response characteristics, limitations of dosimeter design under field conditions, and makes recommendations for effective use of the dosimeters in the field. The manual describes the technical basis for the dosimetry system in a manner intended to help ensure defensibility of the dose of record at Hanford and to demonstrate compliance with requirements of 10 CFR 835, the DOE Laboratory Accreditation Program, the DOE Richland Operations Office, DOE Office of River Protection, DOE Pacific Northwest Office of Science, and Hanford’s DOE contractors. The dosimetry system is operated by the Pacific Northwest National Laboratory (PNNL) Hanford External Dosimetry Program which provides dosimetry services to PNNL and all Hanford contractors. The primary users of this manual are DOE and DOE contractors at Hanford using the dosimetry services of PNNL. Development and maintenance of this manual is funded directly by DOE and DOE contractors. Its contents have been reviewed and approved by DOE and DOE contractors at Hanford through the Hanford Personnel Dosimetry Advisory Committee which is chartered and chaired by DOE-RL and serves as means of coordinating dosimetry practices across contractors at Hanford. This manual was established in 1996. Since its inception, it has been revised many times and maintained by PNNL as a controlled document with controlled distribution. The first revision to be released through PNNL’s Electronic Records & Information Capture Architecture database was designated Revision 0. Revision numbers that are whole numbers reflect major revisions typically involving significant changes to all chapters in the document. Revision

Hanford External Dosimetry Technical Basis Manual PNL-MA-842

Energy Technology Data Exchange (ETDEWEB)

Rathbone, Bruce A.

2011-04-04

The Hanford External Dosimetry Technical Basis Manual PNL-MA-842 documents the design and implementation of the external dosimetry system used at the U.S. Department of Energy (DOE) Hanford site. The manual describes the dosimeter design, processing protocols, dose calculation methodology, radiation fields encountered, dosimeter response characteristics, limitations of dosimeter design under field conditions, and makes recommendations for effective use of the dosimeters in the field. The manual describes the technical basis for the dosimetry system in a manner intended to help ensure defensibility of the dose of record at Hanford and to demonstrate compliance with requirements of 10 CFR 835, the DOE Laboratory Accreditation Program, the DOE Richland Operations Office, DOE Office of River Protection, DOE Pacific Northwest Office of Science, and Hanford’s DOE contractors. The dosimetry system is operated by the Pacific Northwest National Laboratory (PNNL) Hanford External Dosimetry Program which provides dosimetry services to PNNL and all Hanford contractors. The primary users of this manual are DOE and DOE contractors at Hanford using the dosimetry services of PNNL. Development and maintenance of this manual is funded directly by DOE and DOE contractors. Its contents have been reviewed and approved by DOE and DOE contractors at Hanford through the Hanford Personnel Dosimetry Advisory Committee which is chartered and chaired by DOE-RL and serves as means of coordinating dosimetry practices across contractors at Hanford. This manual was established in 1996. Since its inception, it has been revised many times and maintained by PNNL as a controlled document with controlled distribution. The first revision to be released through PNNL’s Electronic Records & Information Capture Architecture database was designated Revision 0. Revision numbers that are whole numbers reflect major revisions typically involving significant changes to all chapters in the document. Revision

Corrective Action Investigation Plan for Corrective Action Unit 571: Area 9 Yucca Flat Plutonium Dispersion Sites, Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Bailey, Bernadine; Matthews, Patrick

2013-07-01

CAU 571 is a grouping of sites where there has been a suspected release of contamination associated with nuclear testing. This document describes the planned investigation of CAU 571, which comprises the following corrective action sites (CASs): • 09-23-03, Atmospheric Test Site S-9F • 09-23-04, Atmospheric Test Site T9-C • 09-23-12, Atmospheric Test Site S-9E • 09-23-13, Atmospheric Test Site T-9D • 09-45-01, Windrows Crater These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the investigation report. The sites will be investigated based on the data quality objectives (DQOs) developed on March 6, 2013, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (now the Nevada Field Office). The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 571. The site investigation process will also be conducted in accordance with the Soils Activity Quality Assurance Plan, which establishes requirements, technical planning, and general quality practices to be applied to this activity. The potential contamination sources associated with CAU 571 CASs are from nuclear testing activities. The DQO process resulted in an assumption that total effective dose (TED) within a default contamination boundary exceeds the final action level (FAL) and requires corrective action. The presence and nature of contamination outside the default

National Ignition Facility Project Site Safety Program

International Nuclear Information System (INIS)

Dun, C

2003-01-01

This Safety Program for the National Ignition Facility (NIF) presents safety protocols and requirements that management and workers shall follow to assure a safe and healthful work environment during activities performed on the NIF Project site. The NIF Project Site Safety Program (NPSSP) requires that activities at the NIF Project site be performed in accordance with the ''LLNL ES and H Manual'' and the augmented set of controls and processes described in this NIF Project Site Safety Program. Specifically, this document: (1) Defines the fundamental NIF site safety philosophy. (2) Defines the areas covered by this safety program (see Appendix B). (3) Identifies management roles and responsibilities. (4) Defines core safety management processes. (5) Identifies NIF site-specific safety requirements. This NPSSP sets forth the responsibilities, requirements, rules, policies, and regulations for workers involved in work activities performed on the NIF Project site. Workers are required to implement measures to create a universal awareness that promotes safe practice at the work site and will achieve NIF management objectives in preventing accidents and illnesses. ES and H requirements are consistent with the ''LLNL ES and H Manual''. This NPSSP and implementing procedures (e.g., Management Walkabout, special work procedures, etc.,) are a comprehensive safety program that applies to NIF workers on the NIF Project site. The NIF Project site includes the B581/B681 site and support areas shown in Appendix B

Corrective Action Investigation Plan for Corrective Action Unit 545: Dumps, Waste Disposal Sites, and Buried Radioactive Materials Nevada Test Site, Nevada

International Nuclear Information System (INIS)

Alfred Wickline

2007-01-01

Corrective Action Unit 545, Dumps, Waste Disposal Sites, and Buried Radioactive Materials, consists of seven inactive sites located in the Yucca Flat area and one inactive site in the Pahute Mesa area. The eight CAU 545 sites consist of craters used for mud disposal, surface or buried waste disposed within craters or potential crater areas, and sites where surface or buried waste was disposed. The CAU 545 sites were used to support nuclear testing conducted in the Yucca Flat area during the 1950s through the early 1990s, and in Area 20 in the mid-1970s. This Corrective Action Investigation Plan has been developed in accordance with the Federal Facility Agreement and Consent Order that was agreed to by the State of Nevada, the U.S. Department of Energy, and the U.S. Department of Defense. Under the Federal Facility Agreement and Consent Order, this Corrective Action Investigation Plan will be submitted to the Nevada Division of Environmental Protection for approval. Fieldwork will be conducted following approval

INTRA/Mod3.2. Manual and code description. Volume 2 - User`s manual

Energy Technology Data Exchange (ETDEWEB)

Andersson, Jenny; Edlund, O.; Hermann, J.; Johansson, Lise-Lotte

1999-01-01

The INTRA Manual consists of two volumes. Volume I of the manual is a thorough description of the code INTRA, the physical modelling of INTRA and the ruling numerics, and volume II, the User`s Manual is an input description. This document, the User`s Manual, Volume II, contains a detailed description of how to use INTRA, how to set up an input file, how to run INTRA and also post-processing

Corrective Action Investigation Plan for Corrective Action Unit 366: Area 11 Plutonium Valley Dispersion Sites, Nevada National Security Site, Nevada

International Nuclear Information System (INIS)

Matthews, Patrick

2011-01-01

Corrective Action Unit 366 comprises the six corrective action sites (CASs) listed below: (1) 11-08-01, Contaminated Waste Dump No.1; (2) 11-08-02, Contaminated Waste Dump No.2; (3) 11-23-01, Radioactively Contaminated Area A; (4) 11-23-02, Radioactively Contaminated Area B; (5) 11-23-03, Radioactively Contaminated Area C; and (6) 11-23-04, Radioactively Contaminated Area D. These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of CAAs that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed July 6, 2011, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 366. The presence and nature of contamination at CAU 366 will be evaluated based on information collected from a field investigation. Radiological contamination will be evaluated based on a comparison of the total effective dose (TED) at sample locations to the dose-based final action level (FAL). The TED will be calculated by summing the estimates of internal and external dose. Results from the analysis of soil samples collected from sample plots will be used to calculate internal radiological dose. Thermoluminescent dosimeters placed at each sample location will be used to measure external radiological dose. Based on historical documentation of the releases

Camp Health Aide Manual = Manual para trabajadores de salud.

Science.gov (United States)

Robinson, June Grube; And Others

This bilingual manual serves as a textbook for migrant Camp Health Aides. Camp Health Aides are members of migrant labor camps enlisted to provide information about health and social services to migrant workers and their families. The manual is divided into 12 tabbed sections representing lessons. Teaching notes printed on contrasting paper…

Investigating Large-Scale Internet Abuse Through Web Page Classification

OpenAIRE

Der, Matthew Francis

2015-01-01

The Internet is rife with abuse: examples include spam, phishing, malicious advertising, DNS abuse, search poisoning, click fraud, and so on. To detect, investigate, and defend against such abuse, security efforts frequently crawl large sets of Web sites that need to be classified into categories, e.g., the attacker behind the abuse or the type of abuse.Domain expertise is often required at first, but classifying thousands to even millions of Web pages manually is infeasible. In this disse...

Corrective Action Investigation Plan for Corrective Action Unit 567: Miscellaneous Soil Sites, Nevada National Security Site, Nevada, with ROTC 1 Revision 0

Energy Technology Data Exchange (ETDEWEB)

Matthews, Patrick K.

2013-07-01

Corrective Action Unit (CAU) 567 is located in Areas 1, 3, 5, 20, and 25 of the Nevada National Security Site, which is approximately 65 miles northwest of Las Vegas, Nevada. CAU 567 is a grouping of sites where there has been a suspected release of contamination associated with nuclear testing. This document describes the planned investigation of CAU 567, which comprises the following corrective action sites (CASs): • 01-23-03, Atmospheric Test Site T-1 • 03-23-25, Seaweed E Contamination Area • 05-23-07, A5b RMA • 20-23-08, Colby Mud Spill • 25-23-23, J-11 Soil RMA These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the investigation report. The sites will be investigated based on the data quality objectives (DQOs) developed on May 6, 2013, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 567. The site investigation process will also be conducted in accordance with the Soils Activity Quality Assurance Plan, which establishes requirements, technical planning, and general quality practices to be applied to this activity. The potential contamination sources associated with CAU 567 releases are nuclear test operations and other NNSS operations. The DQO process resulted in an assumption that total effective dose (TED) within a default contamination boundary

Manual for the sampling of uranium mine tailings

International Nuclear Information System (INIS)

Feenstra, S.; Reades, D.W.; Cherry, J.A.; Chambers, D.B.; Case, G.G.; Ibbotson, B.G.

1983-04-01

The purpose of this manual is to describe the requisite sampling procedures to provide a basis for the application of uniform high-quality standards to detailed geotechnical, hydrogeological, geochemical and air quality measurements at Canadian uranium tailings disposal sites. The report describes the objective and scope of a sampling program, the preliminary data collection, and the procedures for sampling of tailings solids, surface water and seepage, tailings porewater, and wind-blown dust and radon

HVAC system operation manual of IMEF

International Nuclear Information System (INIS)

Baek, Sang Yeol; Park, Dae Kyu; Ahn, Sang Bok; Ju, Yong Sun.

1997-06-01

This manual is operation procedures of the IMEF(Irradiated Material Examination Facility) HVAC(Heating, Ventilation and Air Conditioning) System. General operation procedures and test method of the IMEF HVAC system are described. The manual is as follows; 1. HVAC system operation manual 2. HVAC system management guide 3. HVAC system maintenance manual 4. HVAC system air velocity and flowrate measurement manual 5. HVAC system HEPA filter leak test manual 6. HVAC system charcoal filter leak test manual 7. HVAC system HEPA and charcoal filter exchange manual. (author). 8 tabs

Corrective Action Investigation Plan for Corrective Action Unit 576: Miscellaneous Radiological Sites and Debris Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Matthews, Patrick [Navarro, Las Vegas, NV (United States)

2016-12-01

Corrective Action Unit (CAU) 576 is located in Areas 2, 3, 5, 8, and 9 of the Nevada National Security Site, which is approximately 65 miles northwest of Las Vegas, Nevada. CAU 576 is a grouping of sites where there has been a suspected release of contamination associated with nuclear testing. This document describes the planned investigation of CAU 576, which comprises the following corrective action sites (CASs): 00-99-01, Potential Source Material; 02-99-12, U-2af (Kennebec) Surface Rad-Chem Piping; 03-99-20, Area 3 Subsurface Rad-Chem Piping; 05-19-04, Frenchman Flat Rad Waste Dump ; 09-99-08, U-9x (Allegheny) Subsurface Rad-Chem Piping; 09-99-09, U-9its u24 (Avens-Alkermes) Surface Contaminated Flex Line These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the Corrective Action Decision Document (CADD).

Remedial investigation for the 200-BP-1 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

Buckmaster, M.A.

1991-01-01

The Hanford Site, Richland, Washington, contains over 1500 identified waste sites that will be characterized and remediated over the next 30 years. In support of the ''Hanford Federal Facility Agreement and Consent Order,'' the US Department of Energy has initiated a remedial investigation/feasibility study (RI/FS) at the 200-BP-1 operable unit. The 200-BP-1 RI is the first Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) investigation on the Hanford Site that involves drilling into highly radioactive and chemically contaminated soils. The initial phase of the site characterization is oriented toward determining the nature and extent of any contamination present in the vicinity of the 200-BP-1 operable unit. The major focus of the Phase I RI is the drilling and sampling of 10 inactive waste disposal units which received low level radioactive liquid waste

Preparation of off-site emergency preparedness plans for nuclear installations

International Nuclear Information System (INIS)

1999-10-01

Safety of public, occupational workers and the protection of environment should be assured while activities for economic and social progress are pursued. These activities include the establishment and utilisation of nuclear facilities and use of radioactive sources. This document is issued as a lead document to facilitate preparation of specific site manuals by the Responsible Organisation for emergency response plans at each site to ensure their preparedness to meet any eventuality due to site emergency in order to mitigate its consequences on the health and safety of site personnel. It takes cognizance of an earlier AERB publication on the subject: Safety Manual on Off-Site Emergency Plan for Nuclear Installations, AERB/SM/NISD-2, 1988 and also takes into consideration the urgent need for promoting public awareness and drawing up revised emergency response plans, which has come out in a significant manner after the accidents at Chernobyl and Bhopal

Decrease in use of manual vacuum aspiration in postabortion care in Malawi: a cross-sectional study from three public hospitals, 2008-2012.

Directory of Open Access Journals (Sweden)

Maria L Odland

Full Text Available OBJECTIVES: To investigate the use of manual vacuum aspiration in postabortion care in Malawi between 2008-2012. METHODS: A retrospective cross-sectional study was done at the referral hospital Queen Elisabeth Central Hospital, and the two district hospitals of Chiradzulu and Mangochi. The data were collected simultaneously at the three sites from Feb-March 2013. All records available for women admitted to the gynaecological ward from 2008-2012 were reviewed. Women who had undergone surgical uterine evacuation after incomplete abortion were included and the use of manual vacuum aspiration versus sharp curettage was analysed. RESULTS: Altogether, 5121 women were included. One third (34.2% of first trimester abortions were treated with manual vacuum aspiration, while all others were treated with sharp curettage. There were significant differences between the hospitals and between years. Overall there was an increase in the use of manual vacuum aspiration from 2008 (19.7% to 2009 (31.0%, with a rapid decline after 2010 (28.5% ending at only 4.9% in 2012. Conversely there was an increase in use of sharp curettage in all hospitals from 2010 to 2012. CONCLUSION: Use of manual vacuum aspiration as part of the postabortion care in Malawi is rather low, and decreased from 2010 to 2012, while the use of sharp curettage became more frequent. This is in contrast with current international guidelines.

A Manual of Style.

Science.gov (United States)

Nebraska State Dept. of Education, Lincoln.

This "Manual of Style" is offered as a guide to assist Nebraska State employees in producing quality written communications and in presenting a consistently professional image of government documents. The manual is not designed to be all-inclusive. Sections of the manual discuss formatting documents, memorandums, letters, mailing…

Final Report: Results of Environmental Site Investigation at Sylvan Grove, Kansas

Energy Technology Data Exchange (ETDEWEB)

LaFreniere, Lorraine M [Argonne National Lab. (ANL), Argonne, IL (United States)

2014-09-01

Sylvan Grove is located in western Lincoln County, approximately 60 mi west of Salina, Kansas (Figure 1.1). From 1954 to 1966, the Commodity Credit Corporation (CCC), an agency of the U.S. Department of Agriculture (USDA), operated a grain storage facility at the northeastern edge of Sylvan Grove. During this time, commercial grain fumigants containing carbon tetrachloride were in common use to preserve grain in storage. In 1998, the Kansas Department of Health and Environment (KDHE) found carbon tetrachloride above the maximum contaminant level (MCL) of 5 μg/L in groundwater from one private well used for livestock and lawn and garden watering. The 1998 KDHE sampling at Sylvan Grove was conducted under the USDA private well sampling program. To determine whether the former CCC/USDA facility at Sylvan Grove is a potential contaminant source and its possible relationship to the contamination in groundwater, the CCC/USDA proposed to conduct an environmental site investigation, in accordance with the Intergovernmental Agreement between the KDHE and the Farm Service Agency (FSA) of the USDA. Argonne National Laboratory, on behalf of the CCC/USDA, developed a work plan (Argonne 2012) for the site investigation and a supplemental work plan for indoor and ambient air sampling (Appendix A). The proposed work was approved by the KDHE (2012a, 2013). The investigations were performed by the Environmental Science Division of Argonne National Laboratory, on behalf of the CCC/USDA. The main activities for the site investigation were conducted in June 2012, and indoor and ambient air sampling was performed in February 2013. This report presents the findings of the investigations at Sylvan Grove.

Surface Environmental Surveillance Procedures Manual

International Nuclear Information System (INIS)

Hanf, Robert W.; Poston, Ted M.

2000-01-01

Shows and explains certain procedures needed for surface environmental surveillance. Hanford Site environmental surveillance is conducted by the Pacific Northwest National Laboratory (PNNL) for the U.S. Department of Energy (DOE) under the Surface Environmental Surveillance Project (SESP). The basic requirements for site surveillance are set fourth in DOE Order 5400.1, General Environmental Protection Program Requirements. Guidance for the SESP is provided in DOE Order 5484.1, Environmental Protection, Safety, and Health Protection Information Reporting Requirements and DOE Order 5400.5, Radiation Protection of the Public and Environment. Guidelines for environmental surveillance activities are provided in DOE/EH-0173T, Environmental Regulatory Guide for Radiological Effluent Monitoring and Environmental Surveillance. An environmental monitoring plan for the Hanford Site is outlined in DOE/RL 91-50 Rev. 2, Environmental Monitoring Plan, United States Department of Energy, Richland Operations Office. Environmental surveillance data are used in assessing the impact of current and past site operations on human health and the environment, demonstrating compliance with applicable local, state, and federal environmental regulations, and verifying the adequacy of containment and effluent controls. SESP sampling schedules are reviewed, revised, and published each calendar year in the Hanford Site Environmental Surveillance Master Sampling Schedule. Environmental samples are collected by SESP staff in accordance with the approved sample collection procedures documented in this manual. Personnel training requirements are documented in SESP-TP-01 Rev.2, Surface Environmental Surveillance Project Training Program.

MARS CODE MANUAL VOLUME III - Programmer's Manual

International Nuclear Information System (INIS)

Chung, Bub Dong; Hwang, Moon Kyu; Jeong, Jae Jun; Kim, Kyung Doo; Bae, Sung Won; Lee, Young Jin; Lee, Won Jae

2010-02-01

Korea Advanced Energy Research Institute (KAERI) conceived and started the development of MARS code with the main objective of producing a state-of-the-art realistic thermal hydraulic systems analysis code with multi-dimensional analysis capability. MARS achieves this objective by very tightly integrating the one dimensional RELAP5/MOD3 with the multi-dimensional COBRA-TF codes. The method of integration of the two codes is based on the dynamic link library techniques, and the system pressure equation matrices of both codes are implicitly integrated and solved simultaneously. In addition, the Equation-Of-State (EOS) for the light water was unified by replacing the EOS of COBRA-TF by that of the RELAP5. This programmer's manual provides a complete list of overall information of code structure and input/output function of MARS. In addition, brief descriptions for each subroutine and major variables used in MARS are also included in this report, so that this report would be very useful for the code maintenance. The overall structure of the manual is modeled on the structure of the RELAP5 and as such the layout of the manual is very similar to that of the RELAP. This similitude to RELAP5 input is intentional as this input scheme will allow minimum modification between the inputs of RELAP5 and MARS3.1. MARS3.1 development team would like to express its appreciation to the RELAP5 Development Team and the USNRC for making this manual possible

Quality Manual

Science.gov (United States)

Koch, Michael

The quality manual is the “heart” of every management system related to quality. Quality assurance in analytical laboratories is most frequently linked with ISO/IEC 17025, which lists the standard requirements for a quality manual. In this chapter examples are used to demonstrate, how these requirements can be met. But, certainly, there are many other ways to do this.

Corrective Action Investigation Plan for Corrective Action Unit 190: Contaminated Waste Sites Nevada Test Site, Nevada, Rev. No.: 0

International Nuclear Information System (INIS)

Wickline, Alfred

2006-01-01

Corrective Action Unit (CAU) 190 is located in Areas 11 and 14 of the Nevada Test Site, which is 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 190 is comprised of the four Corrective Action Sites (CASs) listed below: (1) 11-02-01, Underground Centrifuge; (2) 11-02-02, Drain Lines and Outfall; (3) 11-59-01, Tweezer Facility Septic System; and (4) 14-23-01, LTU-6 Test Area. These sites are being investigated because existing information is insufficient on the nature and extent of potential contamination to evaluate and recommend corrective action alternatives. Additional information will be obtained before evaluating corrective action alternatives and selecting the appropriate corrective action for each CAS by conducting a corrective action investigation (CAI). The results of the field investigation will support a defensible evaluation of viable corrective action alternatives that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed on August 24, 2006, by representatives of the Nevada Division of Environmental Protection; U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office; Stoller-Navarro Joint Venture, and National Security Technologies, LLC. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 190. The scope of the CAU 190 CAI includes the following activities: (1) Move surface debris and/or materials, as needed, to facilitate sampling; (2) Conduct radiological and geophysical surveys; (3) Perform field screening; (4) Collect and submit environmental samples for laboratory analysis to determine whether contaminants of concern (COCs) are present; (5) If COCs are present, collect additional step-out samples to define the lateral and vertical extent of the contamination; (6) Collect samples of source material, if present

Dreamweaver CS55 The Missing Manual

CERN Document Server

McFarland, David

2011-01-01

Dreamweaver is the tool most widely used for designing and managing professional-looking websites, but it's a complex program. That's where Dreamweaver CS5.5: The Missing Manual comes in. With its jargon-free explanations, 13 hands-on tutorials, and savvy advice from Dreamweaver expert Dave McFarland, you'll master this versatile program with ease. Get A to Z guidance. Go from building your first web page to creating interactive, database-driven sites.Build skills as you learn. Apply your knowledge through tutorials and downloadable practice files.Create a state-of-the-art website. Use powerf

SHARP User Manual

Energy Technology Data Exchange (ETDEWEB)

Yu, Y. Q. [Argonne National Lab. (ANL), Argonne, IL (United States); Shemon, E. R. [Argonne National Lab. (ANL), Argonne, IL (United States); Thomas, J. W. [Argonne National Lab. (ANL), Argonne, IL (United States); Mahadevan, Vijay S. [Argonne National Lab. (ANL), Argonne, IL (United States); Rahaman, Ronald O. [Argonne National Lab. (ANL), Argonne, IL (United States); Solberg, Jerome [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2016-03-31

SHARP is an advanced modeling and simulation toolkit for the analysis of nuclear reactors. It is comprised of several components including physical modeling tools, tools to integrate the physics codes for multi-physics analyses, and a set of tools to couple the codes within the MOAB framework. Physics modules currently include the neutronics code PROTEUS, the thermal-hydraulics code Nek5000, and the structural mechanics code Diablo. This manual focuses on performing multi-physics calculations with the SHARP ToolKit. Manuals for the three individual physics modules are available with the SHARP distribution to help the user to either carry out the primary multi-physics calculation with basic knowledge or perform further advanced development with in-depth knowledge of these codes. This manual provides step-by-step instructions on employing SHARP, including how to download and install the code, how to build the drivers for a test case, how to perform a calculation and how to visualize the results. Since SHARP has some specific library and environment dependencies, it is highly recommended that the user read this manual prior to installing SHARP. Verification tests cases are included to check proper installation of each module. It is suggested that the new user should first follow the step-by-step instructions provided for a test problem in this manual to understand the basic procedure of using SHARP before using SHARP for his/her own analysis. Both reference output and scripts are provided along with the test cases in order to verify correct installation and execution of the SHARP package. At the end of this manual, detailed instructions are provided on how to create a new test case so that user can perform novel multi-physics calculations with SHARP. Frequently asked questions are listed at the end of this manual to help the user to troubleshoot issues.

SHARP User Manual

International Nuclear Information System (INIS)

Yu, Y. Q.; Shemon, E. R.; Thomas, J. W.; Mahadevan, Vijay S.; Rahaman, Ronald O.; Solberg, Jerome

2016-01-01

SHARP is an advanced modeling and simulation toolkit for the analysis of nuclear reactors. It is comprised of several components including physical modeling tools, tools to integrate the physics codes for multi-physics analyses, and a set of tools to couple the codes within the MOAB framework. Physics modules currently include the neutronics code PROTEUS, the thermal-hydraulics code Nek5000, and the structural mechanics code Diablo. This manual focuses on performing multi-physics calculations with the SHARP ToolKit. Manuals for the three individual physics modules are available with the SHARP distribution to help the user to either carry out the primary multi-physics calculation with basic knowledge or perform further advanced development with in-depth knowledge of these codes. This manual provides step-by-step instructions on employing SHARP, including how to download and install the code, how to build the drivers for a test case, how to perform a calculation and how to visualize the results. Since SHARP has some specific library and environment dependencies, it is highly recommended that the user read this manual prior to installing SHARP. Verification tests cases are included to check proper installation of each module. It is suggested that the new user should first follow the step-by-step instructions provided for a test problem in this manual to understand the basic procedure of using SHARP before using SHARP for his/her own analysis. Both reference output and scripts are provided along with the test cases in order to verify correct installation and execution of the SHARP package. At the end of this manual, detailed instructions are provided on how to create a new test case so that user can perform novel multi-physics calculations with SHARP. Frequently asked questions are listed at the end of this manual to help the user to troubleshoot issues.

Perceptual Confusions of the Manual Alphabet by Naive, Trained, and Familiar Users.

Science.gov (United States)

Hawes, M. Dixie; Danhauer, Jeffrey L.

1980-01-01

An investigation of the confusion resulting from reliance on visual perceptual teachers in the identification of dactylemes (handshapes) in the American Manual Alphabet (MA) is reported. A hierarchy of errors varying with subjects' degree of expertness in the MA is established. This can help manual communication teachers develop techniques for…

River and river-related drainage area parameters for site investigation program

Energy Technology Data Exchange (ETDEWEB)

Blomqvist, P.; Brunberg, A.K. [Uppsala Univ. (Sweden). Dept. of Limnology; Brydsten, L. [Umeaa Univ. (Sweden). Dept. of Ecology and Environmental Science

2001-05-01

In this paper, a number of parameters of importance to a determination of the function of running waters as transport channels for material from the continents to the sea are presented. We have assumed that retention mechanisms of material in the river and in the riparian zone will be covered by special investigations but tried to create a platform for such investigations by quantification of the extension of different main habitats. The choice of parameters has been made so that also the nature conservation value of the river can be preliminary established, and includes a general description of the river type and the inherent ecosystem. The material links directly to that presented in a previous report concerning site investigation programmes for lakes. The parameters have been divided into five groups: 1) The location of the object relative important gradients in the surrounding nature; 2) The river catchment area and its major constituents; 3) The river morphometry; 4) The river ecosystem; 5) Human-induced damages to the river ecosystem. The first two groups, principally based on the climate, hydrology, geology and vegetation of the catchment area, represent parameters that can be used to establish the rarity and representativity of the system, and will in the context of site investigation program be used as a basis for generalisation of the results. The third group, the river morphometry parameters, are standard parameters for the outline of sampling programmes and for calculations of the physical extension of key habitats in the system. The fourth group, the ecosystem of the river, includes physical, chemical and biological parameters required for determination of the influence from the terrestrial ecosystem of the catchment area, nutrient status, distribution of different habitats, and presence of fish in the system. In the context of site investigation program, the parameters in these two groups will be used for budget calculations of the flow of energy and

River and river-related drainage area parameters for site investigation program

International Nuclear Information System (INIS)

Blomqvist, P.; Brunberg, A.K.; Brydsten, L.

2001-05-01

In this paper, a number of parameters of importance to a determination of the function of running waters as transport channels for material from the continents to the sea are presented. We have assumed that retention mechanisms of material in the river and in the riparian zone will be covered by special investigations but tried to create a platform for such investigations by quantification of the extension of different main habitats. The choice of parameters has been made so that also the nature conservation value of the river can be preliminary established, and includes a general description of the river type and the inherent ecosystem. The material links directly to that presented in a previous report concerning site investigation programmes for lakes. The parameters have been divided into five groups: 1) The location of the object relative important gradients in the surrounding nature; 2) The river catchment area and its major constituents; 3) The river morphometry; 4) The river ecosystem; 5) Human-induced damages to the river ecosystem. The first two groups, principally based on the climate, hydrology, geology and vegetation of the catchment area, represent parameters that can be used to establish the rarity and representativity of the system, and will in the context of site investigation program be used as a basis for generalisation of the results. The third group, the river morphometry parameters, are standard parameters for the outline of sampling programmes and for calculations of the physical extension of key habitats in the system. The fourth group, the ecosystem of the river, includes physical, chemical and biological parameters required for determination of the influence from the terrestrial ecosystem of the catchment area, nutrient status, distribution of different habitats, and presence of fish in the system. In the context of site investigation program, the parameters in these two groups will be used for budget calculations of the flow of energy and

Geochemical investigations at Maxey Flats radioactive waste disposal site

International Nuclear Information System (INIS)

Dayal, R.; Pietrzak, R.F.; Clinton, J.

1984-09-01

As part of the NRC efforts to develop a data base on source term characteristics for low level wastes, Brookhaven National Laboratory (BNL) has produced and analyzed a large amount of data on trench leachate chemistry at existing shallow land burial sites. In this report, we present the results of our investigations at the Maxey Flats, Kentucky disposal site. In particular, data on trench leachate chemistry are reviewed and discussed in terms of mechanisms and processes controlling the composition of trench solutes. Particular emphasis is placed on identifying both intra- and extra-trench factors and processes contributing to source term characteristics, modifications, and uncertainties. BNL research on the Maxey Flats disposal site has provided important information not only on the source term characteristics and the factors contributing to uncertainties in the source term but also some generic insights into such geochemical processes and controls as the mechanics of leachate formation, microbial degradation and development of anoxia, organic complexation and radionuclide mobility, redox inversion and modification of the source term, solubility constraints on solute chemistry, mineral authigenesis, corrosion products and radionuclide scavenging, and the role of organic complexants in geochemical partitioning of radionuclides. A knowledge of such processes and controls affecting the geochemical cycling of radionuclides as well as an understanding of the important factors that contribute to variability and uncertainties in the source term is essential for evaluating the performance of waste package and the site, making valid predictions of release for dose calculations, and for planning site performance monitoring as well as remedial actions. 43 references, 47 figures, 30 tables

Evaluation of manual and automatic manually triggered ventilation performance and ergonomics using a simulation model.

Science.gov (United States)

Marjanovic, Nicolas; Le Floch, Soizig; Jaffrelot, Morgan; L'Her, Erwan

2014-05-01

In the absence of endotracheal intubation, the manual bag-valve-mask (BVM) is the most frequently used ventilation technique during resuscitation. The efficiency of other devices has been poorly studied. The bench-test study described here was designed to evaluate the effectiveness of an automatic, manually triggered system, and to compare it with manual BVM ventilation. A respiratory system bench model was assembled using a lung simulator connected to a manikin to simulate a patient with unprotected airways. Fifty health-care providers from different professional groups (emergency physicians, residents, advanced paramedics, nurses, and paramedics; n = 10 per group) evaluated manual BVM ventilation, and compared it with an automatic manually triggered device (EasyCPR). Three pathological situations were simulated (restrictive, obstructive, normal). Standard ventilation parameters were recorded; the ergonomics of the system were assessed by the health-care professionals using a standard numerical scale once the recordings were completed. The tidal volume fell within the standard range (400-600 mL) for 25.6% of breaths (0.6-45 breaths) using manual BVM ventilation, and for 28.6% of breaths (0.3-80 breaths) using the automatic manually triggered device (EasyCPR) (P < .0002). Peak inspiratory airway pressure was lower using the automatic manually triggered device (EasyCPR) (10.6 ± 5 vs 15.9 ± 10 cm H2O, P < .001). The ventilation rate fell consistently within the guidelines, in the case of the automatic manually triggered device (EasyCPR) only (10.3 ± 2 vs 17.6 ± 6, P < .001). Significant pulmonary overdistention was observed when using the manual BVM device during the normal and obstructive sequences. The nurses and paramedics considered the ergonomics of the automatic manually triggered device (EasyCPR) to be better than those of the manual device. The use of an automatic manually triggered device may improve ventilation efficiency and decrease the risk of

Fuel Element Technical Manual

Energy Technology Data Exchange (ETDEWEB)

Burley, H.H. [ed.

1956-08-01

It is the purpose of the Fuel Element Technical Manual to Provide a single document describing the fabrication processes used in the manufacture of the fuel element as well as the technical bases for these processes. The manual will be instrumental in the indoctrination of personnel new to the field and will provide a single data reference for all personnel involved in the design or manufacture of the fuel element. The material contained in this manual was assembled by members of the Engineering Department and the Manufacturing Department at the Hanford Atomic Products Operation between the dates October, 1955 and June, 1956. Arrangement of the manual. The manual is divided into six parts: Part I--introduction; Part II--technical bases; Part III--process; Part IV--plant and equipment; Part V--process control and improvement; and VI--safety.

Site investigation SFR. Hydro Monitoring Program. Report for May 2008-August 2009

Energy Technology Data Exchange (ETDEWEB)

Nyberg, Goeran; Wass, Eva [Geosigma AB, Uppsala (Sweden)

2009-10-15

SKB conducts bedrock investigations for a future extension of the final repository for low- and medium-level radioactive waste (SFR) at Forsmark within the Oesthammar municipality. As a part of this investigation, hydrogeological monitoring is performed. The objectives of the groundwater monitoring are, in a short-term perspective, to measure pressure responses during drilling, pumping and interference tests and also, in a long-term perspective, to create time series in order to increase the knowledge of the hydraulic conditions. Data presented in this report are collected during the period of May 2008 until August 2009 and include groundwater levels in surface boreholes and groundwater pressure in boreholes situated in the tunnel. The data collecting system in HMS (Hydro Monitoring System) consists of a measurement station (computer) that communicates with and collects data from a number of data loggers. The computer is connected to the SKB Ethernet LAN. All data are collected by means of different transducers connected to different types of data loggers: Minitroll, LevelTroll and Datataker. In order to calibrate registrations from the data loggers, manual levelling of all surface borehole sections is made, normally once every month. The logger data are converted to water levels using calibration constants. All collected data are quality checked once every three or four months. During this work, obviously erroneous data are omitted and calibration constants are corrected so that the monitored data comply with the manual levelling. At these occasions the status of the equipment is also checked and service might be initiated. Diagrams of groundwater levels and groundwater pressure for the period of May 2008-August 2009 (one data point per section and twenty-four hours) are presented in Appendix 2. The original data are stored in the primary data base Sicada. The data in this data base may then be used for further analysis. There are no nonconformities with respect

Site investigation SFR. Hydro Monitoring Program. Report for September 2009 - August 2010

Energy Technology Data Exchange (ETDEWEB)

Nyberg, Goeran; Wass, Eva [Geosigma AB, Uppsala (Sweden)

2010-11-15

SKB is conducting bedrock investigations for a future extension of the final repository for low- and medium-level radioactive waste (SFR) at Forsmark within the Oesthammar municipality. As a part of this investigation, hydrogeological monitoring is performed. The objectives of the groundwater monitoring are, in a short-term perspective, to measure pressure responses during drilling, pumping and interference tests and also, in a long-term perspective, to obtain time series in order to increase the knowledge of the hydraulic conditions. Data presented in this report are collected during the period of September 2009 until August 2010 and include groundwater levels in surface boreholes and groundwater pressure in boreholes situated in the tunnel. The data collecting system in HMS (Hydro Monitoring System) consists of a measurement station (computer) that communicates with and collects data from a number of data loggers. The computer is connected to the SKB Ethernet LAN. All data are collected by means of different types of transducers connected to different types of data loggers: Minitroll, LevelTroll and Datataker. In order to calibrate registrations from the data loggers, manual levelling of the groundwater table of all surface borehole sections is made, usually once every month. The logger data are converted to water levels using calibration constants. All collected data are quality checked, generally once every four months. During this work, obviously erroneous data are omitted and calibration constants are corrected so that the monitored data comply with the manual levelling. At these occasions the status of the equipment is also checked and service might be initiated. Diagrams of groundwater levels and groundwater pressure for the period of September 2009 - August 2010 (one data point per section and 24 hours) are presented in Appendix 2. The original data are stored in the primary data base Sicada. The data in this data base may then be used for further analysis

Status of site investigation for L/ILW facilities in the Philippines - 59262

International Nuclear Information System (INIS)

Palattao, Maria V.; Nohay, Carl; Reyes, Rolando; Singayan, Alfonso; Mallants, Dirk

2012-01-01

Document available in abstract form only. Full text of publication follows: Radioactive waste in the Philippines is generated from the various applications of radioactive materials in medicine, industries and research. The Philippine Nuclear Research Institute (PNRI) currently manages these wastes through its centralized treatment and storage facilities on site. Radioactive wastes that are received at the Institute are of different types ranging from contaminated solid and liquid materials to spent sealed sources, including radium. Treated and conditioned wastes are temporarily stored in simple roofed above ground concrete bunkers. The Philippine government through the Inter-agency Subcommittee on Radioactive Waste Management is committed to the development of a national repository for the country's radioactive waste. This policy has been recognized in spite of the relatively small volume of radioactive waste compared with countries that have a nuclear power program. To date, a potential site has been identified for detailed investigation with the assistance of the International Atomic Energy Agency (IAEA). The site is located in the northern part of the Philippine archipelago and has about 34 hectares for potential development. A drilling program that aimed to investigate the geologic, hydrogeologic and hydrologic properties of the site has been implemented

Supplemental Investigation Plan for FFACO Use Restrictions, Nevada Test Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Lynn Kidman

2008-02-01

This document is part of an effort to re-evaluate all FFACO URs against the current RBCA criteria (referred to in this document as the Industrial Sites [IS] RBCA process) as defined in the Industrial Sites Project Establishment of Final Action Levels (NNSA/NSO, 2006a). After reviewing all of the existing FFACO URs, the 12 URs addressed in this Supplemental Investigation Plan (SIP) could not be evaluated against the current RBCA criteria as sufficient information about the contamination at each site was not available. This document presents the plan for conducting field investigations to obtain the needed information. This SIP includes URs from Corrective Action Units (CAUs) 326, 339, 358, 452, 454, 464, and 1010, located in Areas 2, 6, 12, 19, 25, and 29 of the Nevada Test Site, which is approximately 65 miles northwest of Las Vegas, Nevada; and CAU 403, located in Area 3 of the Tonopah Test Range, which is approximately 165 miles north of Las Vegas, Nevada.

SRP baseline hydrogeologic investigation: Aquifer characterization. Groundwater geochemistry of the Savannah River Site and vicinity

Energy Technology Data Exchange (ETDEWEB)

Strom, R.N.; Kaback, D.S.

1992-03-31

An investigation of the mineralogy and chemistry of the principal hydrogeologic units and the geochemistry of the water in the principal aquifers at Savannah River Site (SRS) was undertaken as part of the Baseline Hydrogeologic Investigation. This investigation was conducted to provide background data for future site studies and reports and to provide a site-wide interpretation of the geology and geochemistry of the Coastal Plain Hydrostratigraphic province. Ground water samples were analyzed for major cations and anions, minor and trace elements, gross alpha and beta, tritium, stable isotopes of hydrogen, oxygen, and carbon, and carbon-14. Sediments from the well borings were analyzed for mineralogy and major and minor elements.

CRISP instrument manual

International Nuclear Information System (INIS)

Bucknall, D.G.; Langridge, Sean

1997-05-01

This document is a user manual for CRISP, one of the two neutron reflectomers at ISIS. CRISP is highly automated allowing precision reproducible measurements. The manual provides detailed instructions for the setting-up and running of the instrument and advice on data analysis. (UK)

Salinas : theory manual.

Energy Technology Data Exchange (ETDEWEB)

Walsh, Timothy Francis; Reese, Garth M.; Bhardwaj, Manoj Kumar

2004-08-01

This manual describes the theory behind many of the constructs in Salinas. For a more detailed description of how to use Salinas , we refer the reader to Salinas, User's Notes. Many of the constructs in Salinas are pulled directly from published material. Where possible, these materials are referenced herein. However, certain functions in Salinas are specific to our implementation. We try to be far more complete in those areas. The theory manual was developed from several sources including general notes, a programer-notes manual, the user's notes and of course the material in the open literature.

PCs The Missing Manual

CERN Document Server

Karp, David

2005-01-01

Your vacuum comes with one. Even your blender comes with one. But your PC--something that costs a whole lot more and is likely to be used daily and for tasks of far greater importance and complexity--doesn't come with a printed manual. Thankfully, that's not a problem any longer: PCs: The Missing Manual explains everything you need to know about PCs, both inside and out, and how to keep them running smoothly and working the way you want them to work. A complete PC manual for both beginners and power users, PCs: The Missing Manual has something for everyone. PC novices will appreciate the una

Radiological survey activities: uranium mill tailings remedial action project procedures manual

International Nuclear Information System (INIS)

Little, C.A.; Berven, B.A.; Carter, T.E.

1986-07-01

The US Department of Energy (DOE) was assigned the responsibility for conducting remedial action at 24 sites, which are located in one eastern and nine western states. The DOE's responsibilities are being met through its Uranium Mill Tailings Remedial Action Project Office (UMTRA-PO) in Albuquerque, New Mexico. The purpose of this Procedures Manual is to provide a standardized set of procedures that document in an auditable manner the activities performed by the Radiological Survey Activities (RASA) group in the Dosimetry and Biophysical Transport Section (DABTS) of the Health and Safety Research Division (HASRD) at the Oak Ridge National Laboratory (ORNL), in its role as the Inclusion Survey Contractor (ISC). Members of the RASA group assigned to the UMTRA Project are headquartered in the ORNL/RASA office in Grand Junction, Colorado, and report to the ORNL/RASA Project Manager. The Procedures Manual ensures that the organizational, administrative, and technical activities of the RASA/UMTRA group conform properly to those of the ISC as described in the Vicinity Properties Management and Implementation Manual and the Summary Protocol. This manual also ensures that the techniques and procedures used by the RASA/UMTRA group and contractor personnel meet the requirements of applicable governmental, scientific, and industrial standards

DOE Radiological Control Manual Core Training Program

International Nuclear Information System (INIS)

Scott, H.L.; Maisler, J.

1993-01-01

Over the past year, the Department of Energy (DOE) Office of Health (EH-40) has taken a leading role in the development of new standardized radiological control training programs for use throughout the DOE complex. The Department promulgated its Radiological Control (RadCon) Manual in June 1992. To ensure consistent application of the criteria presented in the RadCon Manual, standardized radiological control core training courses and training materials have been developed for implementation at all DOE facilities. In producing local training programs, standardized core courses are to be supplemented with site-specific lesson plans, viewgraphs, student handbooks, qualification standards, question banks, and wallet-sized training certificates. Training programs for General Employee Radiological Training, Radiological Worker I and II Training, and Radiological Control Technician Training have been disseminated. Also, training committees under the direction of the Office of Health (EH-40) have been established for the development of additional core training courses, development of examination banks, and the update of the existing core training courses. This paper discusses the current activities and future direction of the DOE radiological control core training program

Clean Lead Facility Inventory System user's manual

International Nuclear Information System (INIS)

Garcia, J.F.

1994-12-01

The purpose of this user's manual is to provide instruction and guidance needed to enter and maintain inventory information for the Clean Lead Facility (CLF), PER-612. Individuals responsible for maintaining and using the system should study and understand the information provided. The user's manual describes how to properly use and maintain the CLF Inventory System. Annual, quarterly, monthly, and current inventory reports may be printed from the Inventory System for reporting purposes. Profile reports of each shipment of lead may also be printed for verification and documentation of lead transactions. The CLF Inventory System was designed on Microsoft Access version 2.0. Similar inventory systems are in use at the Idaho National Engineering Laboratory (INEL) to facilitate site-wide compilations of mixed waste data. The CLF Inventory System was designed for inventorying the clean or non-radioactive contaminated lead stored at the CLF. This data, along with the mixed waste data, will be compiled into the Idaho Mixed Waste Information (IMWI) system for reporting to the Department of Energy Idaho Office, Department of Energy Headquarters, and/or the State of Idaho

Integrated Closure and Monitoring Plan for the Area 3 and Area 5 Radioactive Waste Management Sites at the Nevada Test Site

Energy Technology Data Exchange (ETDEWEB)

S. E. Rawlinson

2001-09-01

Bechtel Nevada (BN) manages two low-level Radioactive Waste Management Sites (RWMSs) (one site is in Area 3 and the other is in Area 5) at the Nevada Test Site (NTS) for the U.S. Department of Energy's (DOE's) National Nuclear Security Administration Nevada Operations Office (NNSA/NV). The current DOE Order governing management of radioactive waste is 435.1. Associated with DOE Order 435.1 is a Manual (DOE M 435.1-1) and Guidance (DOE G 435.1-1). The Manual and Guidance specify that preliminary closure and monitoring plans for a low-level waste (LLW) management facility be developed and initially submitted with the Performance Assessment (PA) and Composite Analysis (CA) for that facility. The Manual and Guidance, and the Disposal Authorization Statement (DAS) issued for the Area 3 RWMS further specify that the preliminary closure and monitoring plans be updated within one year following issuance of a DAS. This Integrated Closure and Monitoring Plan (ICMP) fulfills both requirements. Additional updates will be conducted every third year hereafter. This document is an integrated plan for closing and monitoring both RWMSs, and is based on guidance issued in 1999 by the DOE for developing closure plans. The plan does not follow the format suggested by the DOE guidance in order to better accommodate differences between the two RWMSs, especially in terms of operations and site characteristics. The modification reduces redundancy and provides a smoother progression of the discussion. The closure and monitoring plans were integrated because much of the information that would be included in individual plans is the same, and integration provides efficient presentation and program management. The ICMP identifies the regulatory requirements, describes the disposal sites and the physical environment where they are located, and defines the approach and schedule for both closing and monitoring the sites.

Phase I Source Investigation, Heckathorn Superfund Site, Richmond, California

Energy Technology Data Exchange (ETDEWEB)

Kohn, Nancy P; Evans, Nathan R

2002-12-18

This report represents Phase I of a multi-phase approach to a source investigation of DDT at the Heckathorn Superfund Site, Richmond, California, the former site of a pesticide packaging plant, and the adjacent waterway, the Lauritzen Channel. Potential identified sources of contamination were from sloughed material from undredged areas (such as side banks) and from outfall pipes. Objectives of Phase I included the (1) evaluation of pesticide concentrations associated with discharge from outfalls, (2) identification of additional outfalls in the area, (3) identification of type, quantity, and distribution of sediment under the Levin pier, (4) quantification of pesticide concentrations in sediment under the pier, and (5) evaluation of sediment structure and slope stability under the pier. Field operations included the collection of sediment directly from inside the mouths of outfall pipes, when possible, or the deployment of specially designed particle traps where direct sampling was problematic. Passive water samplers were placed at the end of known outfall pipes and analyzed for DDT and other pesticides of concern. Underwater dive surveys were conducted beneath the Levin pier to document type, slope, and thickness of sediment. Samples were collected at locations of interest and analyzed for contaminants. Also sampled was soil from bank areas, which were suspected of potentially contributing to continued DDT contamination of the Lauritzen Channel through erosion and groundwater leaching. The Phase I Source Investigation was successful in identifying significant sources of DDT contamination to Lauritzen Channel sediment. Undredged sediment beneath the Levin pier that has been redistributed to the channel is a likely source. Two outfalls tested bear further investigation. Not as well-defined are the contributions of bank erosional material and groundwater leaching. Subsequent investigations will be based on the results of this first phase.

How does the Augmented Reality Manual enhance cognitive activity while doing complex maintenance tasks?: Augmented Tutorial Overlaid Manual (ATOM)

International Nuclear Information System (INIS)

Yim, Ho Bin; Seong, Poong Hyun

2008-01-01

It has been more than a decade since the concept of Augmented Reality (AR) was introduced. Many related technologies, such as tracking and display, to animate this concept have improved to certain levels. AR is well suited for interaction with the cognitive vision system. In contrast to the virtual reality, AR applications enrich the perceived reality with additional visual information which ranges from text annotation and object highlighting to complex 3D objects. AR has been tested its potentiality in various forms of applications. For example, visitors wear Head Mount Display (HMD) to see virtual guides explaining artifacts in a museum or soldiers are informed geographical features about unfamiliar operation sites. Recently, researchers tried to use AR as a means of teaching or training apparatus; however, there are still some technical obstacles to put this fascinating technology into practice. In this study, we will use Cognitive Load Theory (CLT) to design a manual of pump maintenance and convert it to AR technology to propose a proto type of an on-line AR maintenance manual to prove its possibility as an interactive learning tool

How does the Augmented Reality Manual enhance cognitive activity while doing complex maintenance tasks?: Augmented Tutorial Overlaid Manual (ATOM)

Energy Technology Data Exchange (ETDEWEB)

Yim, Ho Bin; Seong, Poong Hyun [Korea Advanced Institute of Technology and Science, Daejeon (Korea, Republic of)

2008-10-15

It has been more than a decade since the concept of Augmented Reality (AR) was introduced. Many related technologies, such as tracking and display, to animate this concept have improved to certain levels. AR is well suited for interaction with the cognitive vision system. In contrast to the virtual reality, AR applications enrich the perceived reality with additional visual information which ranges from text annotation and object highlighting to complex 3D objects. AR has been tested its potentiality in various forms of applications. For example, visitors wear Head Mount Display (HMD) to see virtual guides explaining artifacts in a museum or soldiers are informed geographical features about unfamiliar operation sites. Recently, researchers tried to use AR as a means of teaching or training apparatus; however, there are still some technical obstacles to put this fascinating technology into practice. In this study, we will use Cognitive Load Theory (CLT) to design a manual of pump maintenance and convert it to AR technology to propose a proto type of an on-line AR maintenance manual to prove its possibility as an interactive learning tool.

Ergonomic Interventions in Manual Handling of Carpets to the retail sellers in a textile company

Directory of Open Access Journals (Sweden)

E. Darvishi

2015-04-01

.Conclusion: By implementing ergonomics interventions in carpet delivery sites, the risk factors of MSDs, induced by manual carpet handling, were reduced and safety and ergonomic conditions of the retailers were improved, compared to the previous conditions.

The role of historical operations information for supporting remedial investigation work at the former Harshaw Chemical Site

International Nuclear Information System (INIS)

Johnson, R.; Peterson, J.; Picel, K.; Kolhoff, A.; Devaughn, J.

2008-01-01

In the early stages of hazardous, toxic, and radioactive waste (HTRW) site investigations, basic record searches are performed to help direct the agencies investigating contaminated sites to areas of concern and to identify contaminants of interest (COI). Plans developed on the basis of this preliminary research alone are often incomplete and result in unexpected discoveries either while in the field investigating the site or after the reports have been written. Many of the sites investigated under the Formerly Utilized Sites Remedial Action program (FUSRAP) have complex histories that are slowly uncovered over the life of the project. Because of programmatic constraints, nuances of these sites are often discovered late in their programs and result in increased expenditures in order to fully characterize the site, perform a robust feasibility study, and recommend appropriate alternatives for remediation. By identifying resources for public records, classified records, historic aerial photographs, and other sources of site-specific historical information, a process can be established to optimize the collection of information and to develop efficient and complete project plans. In many cases, interviews with past site employees are very useful tools. In combining what is found in the records, observed on historic aerial photographs, and heard from former employees and family members, teams investigating these sites can begin to compile sound and more complete conceptual site models (CSMs). The former Harshaw Chemical Site (HCS) illustrates this discovery process. HCS is part of FUSRAP. Preliminary investigations by the US Department of Energy (DOE) in the 1970s provided an initial CSM of activities that had taken place that may have resulted in contamination. The remedial investigation (RI) conducted by the US Army Corps of Engineers (USACE) was designed around this CSM. The RI work, however, identified a number of site conditions that were unexpected, including new

Savannah River Site RCRA Facility Investigation plan: Road A Chemical Basin

International Nuclear Information System (INIS)

1989-06-01

The nature of wastes disposed of at the Road A Chemical Basin (RACB) is such that some degree of soil contamination is probable. Lead has also been detected in site monitoring wells at concentrations above SRS background levels. A RCRA Facility Investigation (RFI) is proposed for the RACB and will include a ground penetrating radar (GPR) survey, collection and chemical and radiological analyses of soil cores, installation of groundwater monitoring wells, collection and chemical and radiological analyses of groundwater samples, and collection of chemical and radiological analyses of surface water and sediment samples. Upon completion of the proposed RFI field work and chemical and radiological analyses, and RFI report should be prepared to present conclusions on the nature and extent of contamination at the site, and to make recommendations for site remediation. If contamination is detected at concentrations above SRS background levels, a receptor analysis should be done to evaluate potential impacts of site contamination on nearby populations

Tank farms criticality safety manual

International Nuclear Information System (INIS)

FORT, L.A.

2003-01-01

This document defines the Tank Farms Contractor (TFC) criticality safety program, as required by Title 10 Code of Federal Regulations (CFR-), Subpart 830.204(b)(6), ''Documented Safety Analysis'' (10 CFR- 830.204 (b)(6)), and US Department of Energy (DOE) 0 420.1A, Facility Safety, Section 4.3, ''Criticality Safety.'' In addition, this document contains certain best management practices, adopted by TFC management based on successful Hanford Site facility practices. Requirements in this manual are based on the contractor requirements document (CRD) found in Attachment 2 of DOE 0 420.1A, Section 4.3, ''Nuclear Criticality Safety,'' and the cited revisions of applicable standards published jointly by the American National Standards Institute (ANSI) and the American Nuclear Society (ANS) as listed in Appendix A. As an informational device, requirements directly imposed by the CRD or ANSI/ANS Standards are shown in boldface. Requirements developed as best management practices through experience and maintained consistent with Hanford Site practice are shown in italics. Recommendations and explanatory material are provided in plain type

FInal Report: Site Investigation Results, 2009-2011, at Inman, Kansas

Energy Technology Data Exchange (ETDEWEB)

LaFreniere, Lorraine M. [Argonne National Lab. (ANL), Argonne, IL (United States). Environmental Sciences Div.

2015-05-01

The Commodity Credit Corporation of the U.S. Department of Agriculture (CCC/USDA) operated a grain storage facility at the southern edge of the city of Inman, Kansas, from 1954 to 1965. During this time, commercial grain fumigants containing carbon tetrachloride were in common use by the grain storage industry to preserve grain in their facilities. In 1997, trace to low levels of carbon tetrachloride (below the maximum contamination level [MCL] of 5.0 μg/L) were detected in three private wells near the former grain storage facility at Inman, as part of a statewide USDA private well sampling program that was implemented by the Kansas Department of Health and Environment (KDHE) near former CCC/USDA facilities. No public water supply wells were identified in 1998 by the KDHE within 1 mi of the town. Carbon tetrachloride is the contaminant of primary concern at sites associated with grain storage operations. To determine whether the former CCC/USDA facility at Inman is a potential contaminant source and its possible relationship to the contamination in groundwater, the CCC/USDA agreed to conduct investigations at Inman. The investigations were performed by the Environmental Science Division of Argonne National Laboratory in accordance with the Intergovernmental Agreement between the KDHE and the Farm Service Agency of the USDA. Argonne, on behalf of the CCC/USDA, developed a Work Plan (Argonne 2007) and subsequently a Summary of Investigation Results and Proposed Work Plan (Appendix A) for a phased site investigation. The proposed work was approved by the KDHE (2007, 2011). The investigations were conducted from November 2009 to September 2011, as proposed in the two work plans. This report presents the findings of the 2009-2011 investigations at Inman.

Final work plan : environmental site investigation at Sylvan Grove, Kansas.

Energy Technology Data Exchange (ETDEWEB)

LaFreniere, L. M. (Environmental Science Division)

2012-07-15

In 1998, carbon tetrachloride was found above the maximum contaminant level (MCL) of 5 {micro}g/L in groundwater from one private livestock well at Sylvan Grove, Kansas, by the Kansas Department of Health and Environment (KDHE). The 1998 KDHE sampling was conducted under the U.S. Department of Agriculture (USDA) private well sampling program. The Commodity Credit Corporation (CCC), a USDA agency, operated a grain storage facility in Sylvan Grove from 1954 to1966. Carbon tetrachloride is the contaminant of primary concern at sites associated with former CCC/USDA grain storage operations. Sylvan Grove is located in western Lincoln County, approximately 60 mi west of Salina (Figure 1.1). To determine whether the former CCC/USDA facility at Sylvan Grove is a potential contaminant source and its possible relationship to the contamination in groundwater, the CCC/USDA has agreed to conduct an investigation, in accordance with the Intergovernmental Agreement between the KDHE and the Farm Service Agency (FSA) of the USDA. This Work Plan presents historical data related to previous investigations, grain storage operations, local private wells and public water supply (PWS) wells, and local geologic and hydrogeologic conditions at Sylvan Grove. The findings from a review of all available documents are discussed in Section 2. On the basis of the analyses of historical data, the following specific technical objectives are proposed for the site investigation at Sylvan Grove: (1) Evaluate the potential source of carbon tetrachloride at the former CCC/USDA facility; (2) Determine the relationship of potential contamination (if present) at the former CCC/USDA facility to contamination identified in 1998 in groundwater samples from one private well to the west; and (3) Delineate the extent of potential contamination associated with the former CCC/USDA facility. The detailed scope of work is outlined in Section 3. The results of the proposed work will provide the basis for determining

Main phases of siting for nuclear power plants with review of required investigations

International Nuclear Information System (INIS)

Malbasa, N.

1984-01-01

The purpose of the article is a short description of the main phases in the process of siting for nuclear power plants as interpreted and applied by the Institut za elektroprivredu, Zagreb in the screening, comparison and evaluation of the sites for NPPs in the SR of Croatia. The scope and purpose, as well as review of required data and investigations for each particular phase are given. Common used methods for the comparison of sites are described and example of rejection criteria applicable for early phases of the siting is proposed. It is given a list of the most important activities which detailed analysis id indispensable for ending of the evaluation and getting a site permit from the regulatory body. A legal and regulatory basis for carrying out the siting process is also described. (author)

Learning of the subject: Methodology of investigation by means of a Site Web.

Directory of Open Access Journals (Sweden)

Yolanda Margarita Carbonell Cabarga

2010-10-01

Full Text Available Results of an investigation are presented having as an objective: the design of a Web Site for the learning of Methodology of Investigation subject in Psychology Bachelor of the Municipal University of Sancti Spíritus. This study was carried out in students of psychology career who were facing first year. Methods of the theoretical and empiric level were applied as well as the Mathematical Statistic. In the diagnosis was possible to appreciate the ignorance regarding the use of the methodology in the therorical methodological design of an investigation, also the difficulties in the study of the subject and violations in the application of orientations from the professors at the time of doing the research papers, so an interactive Web Site was obtained and applied which allow the teaching of the subject. The site was validated by means of a quasi-experiment, the obtained information was processed with the use of the statistical inferentia, results were in general highly significant for the feasibility of the proposal.

Vessel size measurements in angiograms: Manual measurements

International Nuclear Information System (INIS)

Hoffmann, Kenneth R.; Dmochowski, Jacek; Nazareth, Daryl P.; Miskolczi, Laszlo; Nemes, Balazs; Gopal, Anant; Wang Zhou; Rudin, Stephen; Bednarek, Daniel R.

2003-01-01

Vessel size measurement is perhaps the most often performed quantitative analysis in diagnostic and interventional angiography. Although automated vessel sizing techniques are generally considered to have good accuracy and precision, we have observed that clinicians rarely use these techniques in standard clinical practice, choosing to indicate the edges of vessels and catheters to determine sizes and calibrate magnifications, i.e., manual measurements. Thus, we undertook an investigation of the accuracy and precision of vessel sizes calculated from manually indicated edges of vessels. Manual measurements were performed by three neuroradiologists and three physicists. Vessel sizes ranged from 0.1-3.0 mm in simulation studies and 0.3-6.4 mm in phantom studies. Simulation resolution functions had full-widths-at-half-maximum (FWHM) ranging from 0.0 to 0.5 mm. Phantom studies were performed with 4.5 in., 6 in., 9 in., and 12 in. image intensifier modes, magnification factor = 1, with and without zooming. The accuracy and reproducibility of the measurements ranged from 0.1 to 0.2 mm, depending on vessel size, resolution, and pixel size, and zoom. These results indicate that manual measurements may have accuracies comparable to automated techniques for vessels with sizes greater than 1 mm, but that automated techniques which take into account the resolution function should be used for vessels with sizes smaller than 1 mm

Eco-Innovation Manual

DEFF Research Database (Denmark)

O'Hare, Jamie Alexander; McAloone, Tim C.; Pigosso, Daniela Cristina Antelmi

Aim of this manual is to introduce a methodology for the implementation of eco‐innovation within small and medium sized companies in developing and emerging economies. The intended audience of this manual is organizations that provide professional services to guide and support manufacturing compa...... companies to improve their sustainability performance....

Evaluation of manual wheelchair performance in everyday life

NARCIS (Netherlands)

van der Woude, L.H.V.; de Groot, S.; van Drongelen, S.; Janssen, T.W.J.; Haisma, J.; Valent, L.; Veeger, H.E.J.

2009-01-01

Evaluation of wheelchair performance (capacity and skills) is crucial in the investigation of wheeled mobility in people with a spinal cord injury (SCI). Manual wheelchair use is a complex combination of skills, which together determine overall functioning, daily activities, participation, and

Comparison of Manual Refraction Versus Autorefraction in 60 Diabetic Retinopathy Patients.

Science.gov (United States)

Shirzadi, Keyvan; Shahraki, Kourosh; Yahaghi, Emad; Makateb, Ali; Khosravifard, Keivan

2016-07-27

The purpose of the study was to evaluate the comparison of manual refraction versus autorefraction in diabetic retinopathy patients. The study was conducted at the Be'sat Army Hospital from 2013-2015. In the present study differences between two common refractometry methods (manual refractometry and Auto refractometry) in diagnosis and follow up of retinopathy in patients affected with diabetes is investigated. Our results showed that there is a significant difference in visual acuity score of patients between manual and auto refractometry. Despite this fact, spherical equivalent scores of two methods of refractometry did not show a significant statistical difference in the patients. Although use of manual refraction is comparable with autorefraction in evaluating spherical equivalent scores in diabetic patients affected with retinopathy, but in the case of visual acuity results from these two methods are not comparable.

Manual therapy and exercise for rotator cuff disease.

Science.gov (United States)

Page, Matthew J; Green, Sally; McBain, Brodwen; Surace, Stephen J; Deitch, Jessica; Lyttle, Nicolette; Mrocki, Marshall A; Buchbinder, Rachelle

2016-06-10

Management of rotator cuff disease often includes manual therapy and exercise, usually delivered together as components of a physical therapy intervention. This review is one of a series of reviews that form an update of the Cochrane review, 'Physiotherapy interventions for shoulder pain'. To synthesise available evidence regarding the benefits and harms of manual therapy and exercise, alone or in combination, for the treatment of people with rotator cuff disease. We searched the Cochrane Central Register of Controlled Trials (CENTRAL; 2015, Issue 3), Ovid MEDLINE (January 1966 to March 2015), Ovid EMBASE (January 1980 to March 2015), CINAHL Plus (EBSCO, January 1937 to March 2015), ClinicalTrials.gov and the WHO ICTRP clinical trials registries up to March 2015, unrestricted by language, and reviewed the reference lists of review articles and retrieved trials, to identify potentially relevant trials. We included randomised and quasi-randomised trials, including adults with rotator cuff disease, and comparing any manual therapy or exercise intervention with placebo, no intervention, a different type of manual therapy or exercise or any other intervention (e.g. glucocorticoid injection). Interventions included mobilisation, manipulation and supervised or home exercises. Trials investigating the primary or add-on effect of manual therapy and exercise were the main comparisons of interest. Main outcomes of interest were overall pain, function, pain on motion, patient-reported global assessment of treatment success, quality of life and the number of participants experiencing adverse events. Two review authors independently selected trials for inclusion, extracted the data, performed a risk of bias assessment and assessed the quality of the body of evidence for the main outcomes using the GRADE approach. We included 60 trials (3620 participants), although only 10 addressed the main comparisons of interest. Overall risk of bias was low in three, unclear in 14 and high in

Preliminary safety evaluation for the Simpevarp subarea. Based on data and site descriptions after the initial site investigation stage

International Nuclear Information System (INIS)

2005-04-01

The main objectives of this Preliminary safety evaluation (PSE) of the Simpevarp subarea are: to determine, whether the feasibility study's judgement of the suitability of the candidate area with respect to long-term safety holds up in the light of the site investigation data; to provide feedback to continued site investigations and site-specific repository design and to identify site specific scenarios and geoscientific issues for further analyses. The PSE focuses on comparing the attained knowledge of the sites with the suitability criteria as set out by SKB in the report SKB-TR--00-12. These criteria both concern properties of the site judged to be necessary for safety and engineering (requirements) and properties judged to be beneficial (preferences). The findings are then evaluated in order to provide feedback to continued investigations and design work. The PSE does not aim at comparing sites and does not assess compliance with safety and radiation protection criteria. The evaluation shows that even considering remaining uncertainties, the Simpevarp subarea meets all safety requirements and most of the safety preferences. Consequently, from a safety point of view, there is no reason not to continue the Site Investigations of the Simpevarp subarea. There are still uncertainties to resolve and the safety would eventually need to be verified through a full safety assessment. Still, this Preliminary Safety Evaluation demonstrates that it is likely that a safe repository for spent nuclear fuel of the KBS-3 type could be constructed at the site. The following feedback is provided to the site investigations and the associated site modelling: Reducing the uncertainty on the deformation zone geometry within the Simpevarp subarea would allow for a more specified layout, although the sensitivity analysis shows that the space needed is rather robust with respect to uncertainties in the zones. There is substantial uncertainty in the discrete fracture network (DFN) model

Single-Site Palladium(II) Catalyst for Oxidative Heck Reaction: Catalytic Performance and Kinetic Investigations

Energy Technology Data Exchange (ETDEWEB)

Duan, Hui; Li, Mengyang; Zhang, Guanghui; Gallagher, James R.; Huang, Zhiliang; Sun, Yu; Luo, Zhong; Chen, Hongzhong; Miller, Jeffrey T.; Zou, Ruqiang; Lei, Aiwen; Zhao, Yanli

2015-01-01

ABSTRACT: The development of organometallic single-site catalysts (SSCs) has inspired the designs of new heterogeneous catalysts with high efficiency. Nevertheless, the application of SSCs in certain modern organic reactions, such as C-C bond formation reactions, has still been less investigated. In this study, a single-site Pd(II) catalyst was developed, where 2,2'-bipyridine-grafted periodic mesoporous organosilica (PMO) was employed as the support of a Pd(II) complex. The overall performance of the single-site Pd(II) catalyst in the oxidative Heck reaction was then investigated. The investigation results show that the catalyst displays over 99% selectivity for the product formation with high reaction yield. Kinetic profiles further confirm its high catalytic efficiency, showing that the rate constant is nearly 40 times higher than that for the free Pd(II) salt. X-ray absorption spectroscopy reveals that the catalyst has remarkable lifetime and recyclability.

Investigations at the former sites of raw phosphate processing in Germany

International Nuclear Information System (INIS)

Reichelt, Andreas; Weiss, Dietmar; Feige, Sebastian; Wiegand, Jens; Gerler, Juergen

2008-01-01

Raw phosphates have been processed in an industrial scale in Germany approximately since the middle of the 19th century. During the centuries, huge amounts of residues with high mass specific activities have been accumulated. Within the framework of a historical study, we have determined the accumulated radionuclide inventory from 1865 to 2005. The consumption amounts to approx. 150 million tons raw phosphates (corresponds to approx. 2.22*10 14 Bq U-238) with a fraction of national production of approx. 1 million tons. A production of approx. 3 million tons of elemental phosphorus (calcium silicate slag: 3.6*10 13 Bq Ra-226) and approx. 12 million tons of phosphoric acid (phosphogypsum: 2.7*10 13 Bq Ra-226) had been achieved. In the next step, we have looked for the former sites with legacies of the raw phosphate processing industry. 92 sites of former production of phosphate fertilizers, 3 sites of former production of elemental phosphorus and 10 sites of former production of phosphoric acid had been identified. Some of them were selected for more detailed researches regarding the accumulated radionuclide inventory and on-site/laboratory radiological investigations. (author)

FINAS. Example manual. 2

International Nuclear Information System (INIS)

Iwata, Koji; Tsukimori, Kazuyuki; Ueno, Mutsuo

2003-12-01

FINAS is a general purpose structural analysis computer program which was developed by Japan Nuclear Cycle Development Institute for the analysis of static, dynamic and thermal responses of elastic and inelastic structures by the finite element method. This manual contains typical analysis examples that illustrate applications of FINAS to a variety of structural engineering problems. The first part of this manual presents fundamental examples in which numerical solutions by FINAS are compared with some analytical reference solutions, and the second part of this manual presents more complex examples intended for practical application. All the input data images and principal results for each problem are included in this manual for beginners' convenience. All the analyses are performed by using the FINAS Version 13.0. (author)

Corrective Action Investigation Plan for Corrective Action Unit 366: Area 11 Plutonium Valley Dispersion Sites, Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Patrick Matthews

2011-09-01

Corrective Action Unit 366 comprises the six corrective action sites (CASs) listed below: (1) 11-08-01, Contaminated Waste Dump No.1; (2) 11-08-02, Contaminated Waste Dump No.2; (3) 11-23-01, Radioactively Contaminated Area A; (4) 11-23-02, Radioactively Contaminated Area B; (5) 11-23-03, Radioactively Contaminated Area C; and (6) 11-23-04, Radioactively Contaminated Area D. These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of CAAs that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed July 6, 2011, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 366. The presence and nature of contamination at CAU 366 will be evaluated based on information collected from a field investigation. Radiological contamination will be evaluated based on a comparison of the total effective dose (TED) at sample locations to the dose-based final action level (FAL). The TED will be calculated by summing the estimates of internal and external dose. Results from the analysis of soil samples collected from sample plots will be used to calculate internal radiological dose. Thermoluminescent dosimeters placed at each sample location will be used to measure external radiological dose. Based on historical documentation of the releases

Investigation of soil potentially contaminated by monazite processing by-products: case study and suggestion for protocol

International Nuclear Information System (INIS)

Briquet, Claudia

2006-01-01

This work describes a characterization of soil potentially contaminated by monazite chemical processing residues. For case study it was selected a country area of Sao Paulo State, containing a monazite processing by-product depository. The main objective was to evaluate the soil contamination in an area of approximately 18,000 m 2 and esteem the total effective dose equivalent. During the development of this work, it was verified necessity of an investigation protocol, in order to standardize actions of regulatory authorities. A survey of the applicable legislation was carried out, as a tool to support decision making process. The methodology was based on the 'Manual de Gerenciamento de Areas Contaminadas' of CETESB (2001 a), a national document to guide studies of contaminated areas. It was also considered the 'Multi Agency Radiation Survey and Site Manual Investigation - MARSSIM' (2000), a U.S. government document that provides a nationally consensus approach to conduct investigations at potentially contaminated sites. The developed activities had been divided in three general stages: data-collecting and information on the place, identification of soil contamination and its distribution until the depth of 3 meters and evaluation of the associated dose. The evaluation of the radiological impact was carried out considering the worst-case use scenario (most restrictive future use), standing out that the final decision fits to the Brazilian National Nuclear Energy Commission - CNEN. CNEN's scope of responsibility includes determining the site release criteria and the cleanup necessity. (author)

Hanfor site past practice investigation strategy

International Nuclear Information System (INIS)

Thompson, K.M.

1991-01-01

The US Department of Energy (DOE), US Environmental Protection Agency (EPA), and the Washington State Department of Ecology (Ecology) have negotiated a strategy for performing Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and Resource Conservation and Recovery Act (RCRA) Past Practice investigations in a more streamlined manner with a bias-for-action. This strategy provides new concepts for (1) accelerating decision-making by maximizing the use of existing data consistent with data quality objectives and (2) undertaking expedited response actions and/or interim remedial measures as appropriate to either remove threats to human health and welfare and the environment or to reduce risk by reducing toxicity, mobility or volume of contaminants. Since the goal of the program is cleanup, much more emphasis will be placed on initiating and completing waste site cleanups through interim measures. While investigations and studies are important in meeting long-range goals, there is now agreement by the parties that an appropriate and significant portion of the near-term funding resources can and should be dedicated to remedial work, where there is sufficient information from which to plan and implement interim remedial measures. The initial stages of Hanford clean-up will optimize the use of interim cleanup actions when justified and practicable. Existing data will be evaluated as the initial basis for decision-making. If the data are found to be insufficient, additional essential data will be collected to support the IRM in a limited field investigation (LFI). Only data needed to formulate a conceptual model (source to pathway to receptor) and qualitative risk assessment would be obtained. The data quality objectives of the LFI will be established based on the use of the data in deciding on IRMs

Torque and power outputs on different subjects during manual wheelchair propulsion under different conditions

Science.gov (United States)

Hwang, Seonhong; Kim, Seunghyeon; Son, Jongsang; Kim, Youngho

2012-02-01

Manual wheelchair users are at a high risk of pain and injuries to the upper extremities due to mechanical inefficiency of wheelchair propulsion motion. The kinetic analysis of the upper extremities during manual wheelchair propulsion in various conditions needed to be investigated. We developed and calibrated a wheelchair dynamometer for measuring kinetic parameters during propulsion. We utilized the dynamometer to investigate and compare the propulsion torque and power values of experienced and novice users under four different conditions. Experienced wheelchair users generated lower torques with more power than novice users and reacted alertly and sensitively to changing conditions. We expect that these basic methods and results may help to quantitatively evaluate the mechanical efficiency of manual wheelchair propulsion.

Biosafety Manual

Energy Technology Data Exchange (ETDEWEB)

King, Bruce W.

2010-05-18

Work with or potential exposure to biological materials in the course of performing research or other work activities at Lawrence Berkeley National Laboratory (LBNL) must be conducted in a safe, ethical, environmentally sound, and compliant manner. Work must be conducted in accordance with established biosafety standards, the principles and functions of Integrated Safety Management (ISM), this Biosafety Manual, Chapter 26 (Biosafety) of the Health and Safety Manual (PUB-3000), and applicable standards and LBNL policies. The purpose of the Biosafety Program is to protect workers, the public, agriculture, and the environment from exposure to biological agents or materials that may cause disease or other detrimental effects in humans, animals, or plants. This manual provides workers; line management; Environment, Health, and Safety (EH&S) Division staff; Institutional Biosafety Committee (IBC) members; and others with a comprehensive overview of biosafety principles, requirements from biosafety standards, and measures needed to control biological risks in work activities and facilities at LBNL.

Effects of angling and manual handling on pike behaviour investigated by high-resolution positional telemetry

DEFF Research Database (Denmark)

Baktoft, Henrik; Aarestrup, Kim; Berg, Søren

2013-01-01

Human disturbances such as angling and manual handling may have long-term effects on the behaviour of pike, Esox lucius L., an ecologically important species. Using continuous high-resolution positional telemetry, this study compared the swimming activity of handled and unhandled pike in a small...

Transport processes investigation: A necessary first step in site scale characterization plans

International Nuclear Information System (INIS)

Roepke, C.; Glass, R.J.; Brainard, J.; Mann, M.; Kriel, K.; Holt, R.; Schwing, J.

1995-01-01

We propose an approach, which we call the Transport Processes Investigation or TPI, to identify and verify site-scale transport processes and their controls. The TPI aids in the formulation of an accurate conceptual model of flow and transport, an essential first step in the development of a cost effective site characterization strategy. The TPI is demonstrated in the highly complex vadose zone of glacial tills that underlie the Fernald Environmental Remediation Project (FEMP) in Fernald, Ohio. As a result of the TPI, we identify and verify the pertinent flow processes and their controls, such as extensive macropore and fracture flow through layered clays, which must be included in an accurate conceptual model of site-scale contaminant transport. We are able to conclude that the classical modeling and sampling methods employed in some site characterization programs will be insufficient to characterize contaminant concentrations or distributions at contaminated or hazardous waste facilities sited in such media

Site Safety Plan for Lawrence Livermore National Laboratory CERCLA investigations

Energy Technology Data Exchange (ETDEWEB)

Bainer, R.; Duarte, J.

1993-07-01

The safety policy of LLNL is to take every reasonable precaution in the performance of work to protect the environment and the health and safety of employees and the public, and to prevent property damage. With respect to hazardous agents, this protection is provided by limiting human exposures, releases to the environment, and contamination of property to levels that are as low as reasonably achievable (ALARA). It is the intent of this Plan to supply the broad outline for completing environmental investigations within ALARA guidelines. It may not be possible to determine actual working conditions in advance of the work; therefore, planning must allow the opportunity to provide a range of protection based upon actual working conditions. Requirements will be the least restrictive possible for a given set of circumstances, such that work can be completed in an efficient and timely fashion. Due to the relatively large size of the LLNL Site and the different types of activities underway, site-specific Operational Safety Procedures (OSPs) will be prepared to supplement activities not covered by this Plan. These site-specific OSPs provide the detailed information for each specific activity and act as an addendum to this Plan, which provides the general plan for LLNL Main Site operation.

Corrective Action Investigation Plan for Corrective Action Unit 569: Area 3 Yucca Flat Atmospheric Test Sites Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Patrick Matthews; Christy Sloop

2012-02-01

Corrective Action Unit (CAU) 569 is located in Area 3 of the Nevada National Security Site, which is approximately 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 569 comprises the nine numbered corrective action sites (CASs) and one newly identified site listed below: (1) 03-23-09, T-3 Contamination Area (hereafter referred to as Annie, Franklin, George, and Moth); (2) 03-23-10, T-3A Contamination Area (hereafter referred to as Harry and Hornet); (3) 03-23-11, T-3B Contamination Area (hereafter referred to as Fizeau); (4) 03-23-12, T-3S Contamination Area (hereafter referred to as Rio Arriba); (5) 03-23-13, T-3T Contamination Area (hereafter referred to as Catron); (6) 03-23-14, T-3V Contamination Area (hereafter referred to as Humboldt); (7) 03-23-15, S-3G Contamination Area (hereafter referred to as Coulomb-B); (8) 03-23-16, S-3H Contamination Area (hereafter referred to as Coulomb-A); (9) 03-23-21, Pike Contamination Area (hereafter referred to as Pike); and (10) Waste Consolidation Site 3A. Because CAU 569 is a complicated site containing many types of releases, it was agreed during the data quality objectives (DQO) process that these sites will be grouped. These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each study group. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the DQOs developed on September 26, 2011, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office. The DQO

Nevada National Security Site Radiation Protection Program

Energy Technology Data Exchange (ETDEWEB)

Managers' Council, Radiological Control

2018-03-12

This is a shared document required by 10 CFR 835 for all contractors conducting radiological work at the Nevada National Security Site. Please record the Author as "Radiological Control Managers' Council" for consistency with previous RPPs and Rad Con Manuals.

The value of DCIP geophysical surveys for contaminated site investigations

DEFF Research Database (Denmark)

Balbarini, Nicola; Rønde, Vinni Kampman; Maurya, Pradip Kumar

an old factory site by combining traditional geological, hydrological, and contaminant concentration data with DCIP surveys. The plume consisted of xenobiotic organic compounds and inorganics. The study assesses benefits and limitations of DCIP geophysics for contaminated site investigations. A 3D......Geophysical methods are increasingly being used in contaminant hydrogeology to map lithology, hydraulic properties, and contaminant plumes with a high ionic strength. Advances in the Direct Current resistivity and Induced Polarization (DCIP) method allow the collection of high resolution three...... water and below the streambed. Surface DCIP surveys supported the characterization of the spatial variability in geology, hydraulic conductivity and contaminant concentration. Though DCIP data interpretation required additional borehole data, the DCIP survey reduced the number of boreholes required...

ACT Plan: Technical Manual. 2013/2014

Science.gov (United States)

ACT, Inc., 2013

2013-01-01

This manual contains information about the American College Test (ACT) Plan® program. The principal focus of this manual is to document the Plan program's technical adequacy in light of its intended purposes. This manual supersedes the 2011 edition. The content of this manual responds to requirements of the testing industry as established in the…

Infant and Toddler Oral- and Manual-Motor Skills Predict Later Speech Fluency in Autism

Science.gov (United States)

Gernsbacher, Morton Ann; Sauer, Eve A.; Geye, Heather M.; Schweigert, Emily K.; Goldsmith, H. Hill

2008-01-01

Background: Spoken and gestural communication proficiency varies greatly among autistic individuals. Three studies examined the role of oral- and manual-motor skill in predicting autistic children's speech development. Methods: Study 1 investigated whether infant and toddler oral- and manual-motor skills predict middle childhood and teenage speech…

Consistency and accuracy of diagnostic cancer codes generated by automated registration: comparison with manual registration

Directory of Open Access Journals (Sweden)

Codazzi Tiziana

2006-09-01

Full Text Available Abstract Background Automated procedures are increasingly used in cancer registration, and it is important that the data produced are systematically checked for consistency and accuracy. We evaluated an automated procedure for cancer registration adopted by the Lombardy Cancer Registry in 1997, comparing automatically-generated diagnostic codes with those produced manually over one year (1997. Methods The automatically generated cancer cases were produced by Open Registry algorithms. For manual registration, trained staff consulted clinical records, pathology reports and death certificates. The social security code, present and checked in both databases in all cases, was used to match the files in the automatic and manual databases. The cancer cases generated by the two methods were compared by manual revision. Results The automated procedure generated 5027 cases: 2959 (59% were accepted automatically and 2068 (41% were flagged for manual checking. Among the cases accepted automatically, discrepancies in data items (surname, first name, sex and date of birth constituted 8.5% of cases, and discrepancies in the first three digits of the ICD-9 code constituted 1.6%. Among flagged cases, cancers of female genital tract, hematopoietic system, metastatic and ill-defined sites, and oropharynx predominated. The usual reasons were use of specific vs. generic codes, presence of multiple primaries, and use of extranodal vs. nodal codes for lymphomas. The percentage of automatically accepted cases ranged from 83% for breast and thyroid cancers to 13% for metastatic and ill-defined cancer sites. Conclusion Since 59% of cases were accepted automatically and contained relatively few, mostly trivial discrepancies, the automatic procedure is efficient for routine case generation effectively cutting the workload required for routine case checking by this amount. Among cases not accepted automatically, discrepancies were mainly due to variations in coding practice.

Multi-agency radiation survey and site investigation manual (MARSIM). Final report

International Nuclear Information System (INIS)

1997-12-01

The MARSSIM provides information on planning, conducting, evaluating, and documenting building surface and surface soil final status radiological surveys for demonstrating compliance with dose or risk-based regulations or standards. The MARSSIM is a multi-agency consensus document that was developed collaboratively by four Federal agencies having authority and control over radioactive materials: Department of Defense (DOD), Department of Energy (DOE), Environmental Protection Agency (EPA), and Nuclear Regulatory Commission (NRC). The MARSSIM's objective is to describe a consistent approach for planning, performing, and assessing building surface and surface soil final status surveys to meet established dose or risk-based release criteria, while at the same time encouraging an effective use of resources

Multi-agency radiation survey and site investigation manual (MARSIM). Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

The MARSSIM provides information on planning, conducting, evaluating, and documenting building surface and surface soil final status radiological surveys for demonstrating compliance with dose or risk-based regulations or standards. The MARSSIM is a multi-agency consensus document that was developed collaboratively by four Federal agencies having authority and control over radioactive materials: Department of Defense (DOD), Department of Energy (DOE), Environmental Protection Agency (EPA), and Nuclear Regulatory Commission (NRC). The MARSSIM`s objective is to describe a consistent approach for planning, performing, and assessing building surface and surface soil final status surveys to meet established dose or risk-based release criteria, while at the same time encouraging an effective use of resources.

Modelling of water-rock interaction at TVO investigation sites

International Nuclear Information System (INIS)

Pitkaenen, P.; Leino-Forsman, H.

1992-12-01

The geochemistry of the groundwater at the Kivetty, Syyry and Olkiluoto site investigation areas in Finland for nuclear waste disposal is evaluated. The hydrogeological data is collected from boreholes drilled down to 100-m depth into crystalline bedrock. The interpretation is based on groundwater chemistry and isotope data, mineralogical data, and the structure and hydrology of the bedrock, using correlation diagrams and the thermodynamic calculations (PHREEQE,EQ3NR). The hydrogeochemistry and major processes controlling the groundwater chemistry are discussed

Comparison of Manual Refraction Versus Autorefraction in 60 Diabetic Retinopathy Patients

OpenAIRE

Shirzadi, Keyvan; Shahraki, Kourosh; Yahaghi, Emad; Makateb, Ali; Khosravifard, Keivan

2016-01-01

Aim: The purpose of the study was to evaluate the comparison of manual refraction versus autorefraction in diabetic retinopathy patients. Material and Methods: The study was conducted at the Be?sat Army Hospital from 2013-2015. In the present study differences between two common refractometry methods (manual refractometry and Auto refractometry) in diagnosis and follow up of retinopathy in patients affected with diabetes is investigated. Results: Our results showed that there is a significant...

On-Site Detection as a Countermeasure to Chemical Warfare/Terrorism.

Science.gov (United States)

Seto, Y

2014-01-01

On-site monitoring and detection are necessary in the crisis and consequence management of wars and terrorism involving chemical warfare agents (CWAs) such as sarin. The analytical performance required for on-site detection is mainly determined by the fatal vapor concentration and volatility of the CWAs involved. The analytical performance for presently available on-site technologies and commercially available on-site equipment for detecting CWAs interpreted and compared in this review include: classical manual methods, photometric methods, ion mobile spectrometry, vibrational spectrometry, gas chromatography, mass spectrometry, sensors, and other methods. Some of the data evaluated were obtained from our experiments using authentic CWAs. We concluded that (a) no technologies perfectly fulfill all of the on-site detection requirements and (b) adequate on-site detection requires (i) a combination of the monitoring-tape method and ion-mobility spectrometry for point detection and (ii) a combination of the monitoring-tape method, atmospheric pressure chemical ionization mass spectrometry with counterflow introduction, and gas chromatography with a trap and special detectors for continuous monitoring. The basic properties of CWAs, the concept of on-site detection, and the sarin gas attacks in Japan as well as the forensic investigations thereof, are also explicated in this article. Copyright © 2014 Central Police University.

Forsmark site investigation. Monitoring of brook water levels, electrical conductivities, temperatures and discharges January-December 2010

Energy Technology Data Exchange (ETDEWEB)

Johansson, Per-Olof (Artesia Grundvattenkonsult (Sweden)); Juston, John (Juston Konsult (Sweden))

2011-06-15

This document reports the monitoring of water levels, electrical conductivities, temperatures and discharges at four brook discharge gauging stations, and the monitoring of water electrical conductivity at the outlet of Lake Bolundsfjaerden in the Forsmark area. The report presents data from 1 January through 31 December 2010 and is a continuation of reporting from Johansson and Juston (2007, 2009, 2011), which covered the periods from 1 April 2004 through 31 March 2007, 1 April 2007 through 31 December 2008, and 1 January through 31 December 2009, respectively. Long-throated flumes equipped with automatically recording devices were used for the discharge measurements. Every c. 14 days the water depths at the upstream edge of the flumes were measured manually by a ruler as a check. Electrical conductivity and temperature were automatically recorded and these parameters were also measured manually every c. 14 days with the site investigation field devices. SKB's Hydro Monitoring System (HMS) was used to collect and store all data. From HMS quality assured data were transferred to SKB's primary database Sicada. Measurements of levels, electrical conductivities and temperatures were made every 10 minutes (every 30 minutes for electrical conductivity at the outlet of Lake Bolundsfjaerden). For the calculation of discharge, quality assured water level data from the flumes were used. The calculation procedure included consolidation of the time series to hourly averages, screening of data for removal of short-term spikes, noise and other data that were judged erroneous. After the calculations were performed, the results were delivered to Sicada. The amplitudes of water level variations during this reporting period were 0.41-0.55 m and the mean electrical conductivities varied between 23 and 39 mS/m at the four discharge stations. However, due to mal-function of measuring devices for electrical conductivity, data were missing for relatively long time periods. Due

GRACE manual

International Nuclear Information System (INIS)

Ishikawa, T.; Kawabata, S.; Shimizu, Y.; Kaneko, T.; Kato, K.; Tanaka, H.

1993-02-01

This manual is composed of three kinds of objects, theoretical background for calculating the cross section of elementary process, usage and technical details of the GRACE system. Throughout this manual we take the tree level process e + e - → W + W - γ as an example, including the e ± -scalar boson interactions. The real FORTRAN source code for this process is attached in the relevant sections as well as the results of calculation, which might be a great help for understanding the practical use of the system. (J.P.N.)

Version I of the users manual for the Tuff Data Base Interface

International Nuclear Information System (INIS)

Langkopf, B.S.; Satter, B.J.; Welch, E.P.

1985-04-01

The Nevada Nuclear Waste Storage Investigations (NNWSI) project, managed by the Nevada Operations Office of the US Department of Energy, is investigating the feasibility of locating a repository at Yucca Mountain on and adjacent to the Nevada Test Site (NTS) in southern Nevada. A part of this investigation includes obtaining physical properties from laboratory tests on samples from Yucca Mountain and field tests of the in situ tuffs at Yucca Mountain. A computerized data base has been developed to store this data in a centralized location. The data base is stored on the Cyber 170/855 computer at Sandia using the System 2000 Data Base Management software. A user-friendly interface, the Tuff Data Base Interface, is being developed to allow NNWSI participants to retrieve information from the Tuff Data Base directly. The Interface gives NNWSI users a great deal of flexibility in retrieving portions of the Data Base. This report is an interim users manual for the Tuff Data Base Interface, as of August 1984. It gives basic instructions on accessing the Sandia computing system and explains the Interface on a question-by-question basis

EML procedures manual

International Nuclear Information System (INIS)

Volchok, H.L.; de Planque, G.

1982-01-01

This manual contains the procedures that are used currently by the Environmental Measurements Laboratory of the US Department of Energy. In addition a number of analytical methods from other laboratories have been included. These were tested for reliability at the Battelle, Pacific Northwest Laboratory under contract with the Division of Biomedical and Environmental Research of the AEC. These methods are clearly distinguished. The manual is prepared in loose leaf form to facilitate revision of the procedures and inclusion of additional procedures or data sheets. Anyone receiving the manual through EML should receive this additional material automatically. The contents are as follows: (1) general; (2) sampling; (3) field measurements; (4) general analytical chemistry; (5) chemical procedures; (6) data section; (7) specifications

Partners Plus: Families and Caregivers in Partnerships. A Family-Centered Guide to Respite Care. Trainer's Workshop Manual [and] Community Planning Manual [and] A Family Manual [and] Caregiver Manual.

Science.gov (United States)

Ownby, Lisa L.; Hooke, Amanda C.; Moore, Dee Wylie; Garland, Corinne W.; Frank, Adrienne

Four manuals on implementing the Partners Respite Model, which provides respite care for children with disabilities or chronic illnesses, comprise this document. The Community Planning Manual offers a step-by-step guide to replication of the Partners Respite Model and is divided into sections on developing the Partners program, implementing the…

Impact of manual preference on directionality in children's drawings.

Science.gov (United States)

Picard, Delphine

2011-01-01

The effects of handedness on directionality in drawing are already well documented in the literature, at least as far as adults are concerned. The present study investigates the impact of manual preference on directionality as seen in the drawing product and drawing process, from a developmental point of view. A total of 120 children aged 5 to 9, both right and left-handed drawers, volunteered for the study. Children were asked to draw twice from memory a set of six common objects. Results indicate that directionality in drawing product varies significantly according to manual preference in the 9-year-old children, but not in the younger age groups. The concomitant increase between 7 and 9 years of age in the use of preferred stroke directions and the impact of manual preference in the drawing process suggests that biomechanical factors might play an important role in behavioural asymmetries in drawing.

The ISIS Open GENIE user manual

International Nuclear Information System (INIS)

Akeroyd, F.A.; Ashworth, R.L.; Campbell, S.I.; Johnston, S.D.; Martin, J.M.; Moreton-Smith, C.M.; Sivia, D.S.

2000-01-01

This manual should enable you to become familiar with Open GENIE quickly and easily. It therefore complements the Open GENIE Reference Manual which should be used to understand the full meaning of Open GENIE commands. The reference manual is accessible on the ISIS web server at: http://www.isis.rl.ac.uk/GENIEReferenceManual/ and the user manual is planned to be accessible by January '98 at http://www.isis.rl.ac.ukIGENIEUserManual/. The Open GENIE User Manual is separated into two parts: Part A. The User Manual. An introduction to the use of Open GENIE. Part B. The Installation Guide. General information on how to install and run Open GENIE. Assuming that you are new to Open GENIE and have just downloaded a copy you will need to consult the Installation Guide to get Open GENIE installed on your machine. After this we recommend you experiment with some of the example files to get an idea of the capabilities of Open GENIE. For further information, comments, additions of routines that you feel should be included, please contact us at genie at isise.rl.ac.uk

Manual on brachytherapy. Incorporating: Applications guide, procedures guide, basics guide

International Nuclear Information System (INIS)

1996-01-01

This publication is part of practical radiation safety manual series for different fields of application aimed primarily at persons handling radiation sources on a daily routine basis, which could at same time be used by the competent authorities, supporting their efforts in the radiation protection training of workers or medical assistance personnel or helping on-site management to set up local radiation protection rules. It is dedicated to brachytherapy: its application and procedures guides

The operation and maintenance manual

International Nuclear Information System (INIS)

Stoll, A.; Krotil, H.; Klein, W.

1976-01-01

The operating manual is one of many technical documents which the nuclear power plant operator needs for ensuring safe operation. For the operating staff, however, there is only one document, namely the operating manual. The operating manual is an essential element in bringing man and machine in harmony. This is necessary for safe and, as far as possible, uninterrupted operation of the power plant. The operating manual is the only document containing binding instructions for plant operation. All the tasks of plant operation which are carried out by plant staff are described in the operating manual in a form which is as clear and comprehensible as possible. A considerable number of these tasks can only be carried out by man, namely: 1) tasks concerning operational organization, 2) all non-automated areas of plant operation. (orig./TK) [de

Fire Protection Program Manual

Energy Technology Data Exchange (ETDEWEB)

Sharry, J A

2012-05-18

This manual documents the Lawrence Livermore National Laboratory (LLNL) Fire Protection Program. Department of Energy (DOE) Orders 420.1B, Facility Safety, requires LLNL to have a comprehensive and effective fire protection program that protects LLNL personnel and property, the public and the environment. The manual provides LLNL and its facilities with general information and guidance for meeting DOE 420.1B requirements. The recommended readers for this manual are: fire protection officers, fire protection engineers, fire fighters, facility managers, directorage assurance managers, facility coordinators, and ES and H team members.

Good clinical practice regulatory inspections: Lessons for Indian investigator sites

Directory of Open Access Journals (Sweden)

R Marwah

2010-01-01

Full Text Available Regulatory inspections are important to evaluate the integrity of the data submitted to health authorities (HAs, protect patient safety, and assess adequacy of site/sponsor quality systems to achieve the same. Inspections generally occur after submission of data for marketing approval of an investigational drug. In recent years, there has been a significant increase in number of inspections by different HAs, including in India. The assessors/inspectors generally do a thorough review of site data before inspections. All aspects of ICH-GCP, site infrastructure, and quality control systems are assessed during the inspection. Findings are discussed during the close out meeting and a detailed inspection report issued afterward, which has to be responded to within 15-30 days with effective Corrective and Preventive Action Plan (CAPA. Protocol noncompliance, inadequate/inaccurate records, inadequate drug accountability, informed consent issues, and adverse event reporting were some of the most common findings observed during recent Food and Drug Administration (FDA inspections. Drug development is being increasingly globalized and an increased number of patients enrolled in studies submitted as part of applications come from all over the world including India. Because of the steep increase in research activity in the country, inexperienced sites, and more stakeholders, increased efforts will be required to ensure continuous quality and compliance. HAs have also made clear that enforcement will be increased and be swift, aggressive, and effective.

ARS-Media for excel instruction manual

Science.gov (United States)

ARS-Media for Excel Instruction Manual is the instruction manual that explains how to use the Excel spreadsheet ARS-Media for Excel application. ARS-Media for Excel Instruction Manual is provided as a pdf file....

A summary of INSITE activities in tracking SKB's spent fuel repository site investigations from 2002-2009 and of advice provided to the regulatory authorities on the status of site understanding at the end of the surface-based investigations

International Nuclear Information System (INIS)

Chapman, Neil; Bath, Adrian; Geier, Joel; Ove Stephansson; Tiren, Sven; Tsang, Chin-Fu

2010-11-01

SSM and its predecessor SKI employed a team of earth scientists who followed and reviewed SKB's investigations of the potential spent nuclear fuel repository sites at Forsmark and Laxemar. This group was named INSITE (INdependent Site Investigation Tracking and Evaluation) and began its work in 2002 and completed its task with the review of the final versions SKB's site descriptive models, SDM-Site, in 2009. This report is a summary of INSITE's work over the eight-and-a-half year period of the site investigations and the lead-in and the wind-down to the work. It is intended to provide an outline and a record of how INSITE has worked and how its advice was generated and provided to SKI and, latterly, to SSM. Together with all the other documentation generated by INSITE, this report is intended to support the regulatory review of SKB's licence application for a spent nuclear fuel repository

Salinas : theory manual.

Energy Technology Data Exchange (ETDEWEB)

Walsh, Timothy Francis; Reese, Garth M.; Bhardwaj, Manoj Kumar

2011-11-01

Salinas provides a massively parallel implementation of structural dynamics finite element analysis, required for high fidelity, validated models used in modal, vibration, static and shock analysis of structural systems. This manual describes the theory behind many of the constructs in Salinas. For a more detailed description of how to use Salinas, we refer the reader to Salinas, User's Notes. Many of the constructs in Salinas are pulled directly from published material. Where possible, these materials are referenced herein. However, certain functions in Salinas are specific to our implementation. We try to be far more complete in those areas. The theory manual was developed from several sources including general notes, a programmer notes manual, the user's notes and of course the material in the open literature.

The Image of User Instructions: Comparing Users' Expectations of and Experiences with an Official and a Commercial Software Manual

NARCIS (Netherlands)

de Jong, Menno D.T.; Karreman, Joyce

2017-01-01

Purpose: The market for (paid-for) commercial software manuals is flourishing, while (free) official manuals are often assumed to be neglected by users. To investigate differences in user perceptions of commercial and official manuals, we conducted two studies: one focusing on user expectations and

Integrated Fuel-Coolant Interaction (IFCI 7.0) Code User's Manual

International Nuclear Information System (INIS)

Young, Michael F.

1999-01-01

The integrated fuel-coolant interaction (IFCI) computer code is being developed at Sandia National Laboratories to investigate the fuel-coolant interaction (FCI) problem at large scale using a two-dimensional, three-field hydrodynamic framework and physically based models. IFCI will be capable of treating all major FCI processes in an integrated manner. This document is a description of IFCI 7.0. The user's manual describes the hydrodynamic method and physical models used in IFCI 7.0. Appendix A is an input manual provided for the creation of working decks

Savannah River Site RCRA/CERCLA/NEPA integrated investigation case study

International Nuclear Information System (INIS)

Clark, D.R.; Thomas, R.; Wilson, M.P.

1992-01-01

The Savannah River Site (SRS) is a US Department of Energy facility placed on the Superfund National Priority List in 1989. Numerous past disposal facilities and contaminated areas are undergoing the integrated regulatory remediation process detailed in the draft SRS Federal Facility Agreement. This paper will discuss the integration of these requirements by highlighting the investigation of the D-Area Burning/Rubble Pits, a typical waste unit at SRS

Remedial investigation/feasibility study for the David Witherspoon, Inc., 901 Site, Knoxville, Tennessee: Volume 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-10-01

This remedial investigation (RI)/feasibility study (FS) supports the selection of remedial actions for the David Witherspoon, Inc. 901 Maryville Pike Site in Knoxville, Tennessee. Operations at the site, used as a recycling center, have resulted in past, present, and potential future releases of hazardous substances in to the environment. This Site is a Tennessee Superfund site. A phased approach was planned to (1) gather existing data from previous investigations managed by the Tenn. Dept. of Environment and Conservation; (2) perform a preliminary RI, including risk assessments, and an FS with existing data to identify areas where remedial action may be necessary; (3) gather additional field data to adequately define the nature and extent of risk-based contaminants that present identifiable threats to human and/or ecological receptors; and (4) develop remedial action alternatives to reduce risks to acceptable levels.

Remedial investigation/feasibility study for the David Witherspoon, Inc., 901 Site, Knoxville, Tennessee: Volume 1

International Nuclear Information System (INIS)

1996-10-01

This remedial investigation (RI)/feasibility study (FS) supports the selection of remedial actions for the David Witherspoon, Inc. 901 Maryville Pike Site in Knoxville, Tennessee. Operations at the site, used as a recycling center, have resulted in past, present, and potential future releases of hazardous substances in to the environment. This Site is a Tennessee Superfund site. A phased approach was planned to (1) gather existing data from previous investigations managed by the Tenn. Dept. of Environment and Conservation; (2) perform a preliminary RI, including risk assessments, and an FS with existing data to identify areas where remedial action may be necessary; (3) gather additional field data to adequately define the nature and extent of risk-based contaminants that present identifiable threats to human and/or ecological receptors; and (4) develop remedial action alternatives to reduce risks to acceptable levels

The use of small diameter probing equipment for contaminated site investigation

International Nuclear Information System (INIS)

Christy, T.M.; Spradlin, S.C.

1992-01-01

The past decade has witnessed a dramatic increase in the number of contaminated sites being investigated in the United States. This increase in subsurface investigation has spurred a corresponding increase in the development of subsurface sampling tools and methods. The past five years, in particular, have seen the development of small diameter (1 double-prime to 1.4 double-prime O.D.) percussion driven probing tools which can be used for the recovery of soil vapor, soil core and groundwater samples. This development has placed heretofore unavailable tools at the disposal of site investigators. Mechanized, vehicle mounted soil probe systems apply both static force and hydraulically powered percussion hammers for tool placement. Static down forces up to 3,000 lbs combined with percussion hammers of eight (8) horsepower continuous output are typical on equipment available to the field investigator. Using these energies, probing tools have been used for sampling a variety of media at depths exceeding 70 feet. Advantages of probing equipment which have contributed to its increasing usage in recent years include: ease of mobilization, absence of borehole cuttings, minimization of surface disturbance, and speed of sample collection. This paper focuses on the field application of hydraulic probing equipment including: the suitability of probing operations with respect to various Boil types and lithologies to probing operations; sampler types and recovery quantities for various media, and innovative probing applications presently being tested

TJ-II Library Manual (Version 2)

International Nuclear Information System (INIS)

Tribaldos, V.; Milligen, B. Ph. van; Lopez-Fraguas, A.

2001-01-01

This is a manual of use of the TJ2 Numerical Library that has been developed for making numerical computations of different TJ-II configurations. This manual is a new version of the earlier manual CIEMAT report 806. (Author)

Effect of cold conditions on manual performance while wearing petroleum industry protective clothing.

Science.gov (United States)

Wiggen, Øystein Nordrum; Heen, Sigri; Færevik, Hilde; Reinertsen, Randi Eidsmo

2011-01-01

The purpose of this study was to investigate manual performance and thermal responses during low work intensity in persons wearing standard protective clothing in the petroleum industry when they were exposed to a range of temperatures (5, -5, -15 and -25℃) that are relevant to environmental conditions for petroleum industry personnel in northern regions. Twelve men participated in the study. Protective clothing was adjusted for the given cold exposure according to current practices. The subjects performed manual tests five times under each environmental condition. The manual performance test battery consisted of four different tests: tactile sensation (Semmes-Weinstein monofilaments), finger dexterity (Purdue Pegboard), hand dexterity (Complete Minnesota dexterity test) and grip strength (grip dynamometer). We found that exposure to -5℃ or colder lowered skin and body temperatures and reduced manual performance during low work intensity. In conclusion the current protective clothing at a given cold exposure is not adequate to maintain manual performance and thermal balance for petroleum workers in the high north.

Remedial investigation/feasibility study work plan for the 100-BC-2 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1993-05-01

This work plan and attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) remedial investigation/feasibility study (RI/FS) for the 100-BC-2 operable unit in the 100 Area of the Hanford Site. The 100 Area is one of four areas at the Hanford Site that are on the US Environmental Protection Agency's (EPA) National Priorities List under CERCLA. The 100-BC-2 operable unit is one of two source operable units in the 100-B/C Area (Figure ES-1). Source operable units are those that contain facilities and unplanned release sites that are potential sources of hazardous substance contamination. The 100-BC-2 source operable unit contains waste sites that were formerly in the 100-BC-2, 100-BC-3, and 100-BC-4 operable units. Because of their size and geographic location, the waste sites from these two operable units were added to 100-BC-2. This allows for a more efficient and effective investigation of the remaining 100-B/C Reactor area waste sites. The investigative approach to waste sites associated with the 100-BC-2 operable unit are listed in Table ES-1. The waste sites fall into three general categories: high priority liquid waste disposal sites, low priority liquid waste disposal sites, and solid waste burial grounds. Several sites have been identified as candidates for conducting an IRM. Two sites have been identified as warranting additional limited field sampling. The two sites are the 116-C-2A pluto crib, and the 116-C-2C sand filter

Architectural study of the design and operation of advanced force feedback manual controllers

Science.gov (United States)

Tesar, Delbert; Kim, Whee-Kuk

1990-01-01

A teleoperator system consists of a manual controller, control hardware/software, and a remote manipulator. It was employed in either hazardous or unstructured, and/or remote environments. In teleoperation, the main-in-the-loop is the central concept that brings human intelligence to the teleoperator system. When teleoperation involves contact with an uncertain environment, providing the feeling of telepresence to the human operator is one of desired characteristics of the teleoperator system. Unfortunately, most available manual controllers in bilateral or force-reflecting teleoperator systems can be characterized by their bulky size, high costs, or lack of smoothness and transparency, and elementary architectures. To investigate other alternatives, a force-reflecting, 3 degree of freedom (dof) spherical manual controller is designed, analyzed, and implemented as a test bed demonstration in this research effort. To achieve an improved level of design to meet criteria such as compactness, portability, and a somewhat enhanced force-reflecting capability, the demonstration manual controller employs high gear-ratio reducers. To reduce the effects of the inertia and friction on the system, various force control strategies are applied and their performance investigated. The spherical manual controller uses a parallel geometry to minimize inertial and gravitational effects on its primary task of transparent information transfer. As an alternative to the spherical 3-dof manual controller, a new conceptual (or parallel) spherical 3-dof module is introduced with a full kinematic analysis. Also, the resulting kinematic properties are compared to those of other typical spherical 3-dof systems. The conceptual design of a parallel 6-dof manual controller and its kinematic analysis is presented. This 6-dof manual controller is similar to the Stewart Platform with the actuators located on the base to minimize the dynamic effects. Finally, a combination of the new 3-dof and 6-dof

77 FR 43606 - Preliminary Damage Assessment for Individual Assistance Operations Manual (9327.2-PR)

Science.gov (United States)

2012-07-25

... site at http://www.fema.gov . The proposed and final manual, all related Federal Register Notices, and... for conducting IA PDAs is to identify the impact, type, and extent of disaster damages and to... to recover. The PDA is an important first step in the disaster declaration process. The information...

Phantom Study Investigating the Accuracy of Manual and Automatic Image Fusion with the GE Logiq E9: Implications for use in Percutaneous Liver Interventions

Energy Technology Data Exchange (ETDEWEB)

Burgmans, Mark Christiaan, E-mail: m.c.burgmans@lumc.nl; Harder, J. Michiel den, E-mail: chiel.den.harder@gmail.com; Meershoek, Philippa, E-mail: P.Meershoek@lumc.nl [Leiden University Medical Centre, Department of Radiology (Netherlands); Berg, Nynke S. van den, E-mail: N.S.van-den-Berg@lumc.nl [Leiden University Medical Center, Interventional and Molecular Imaging Laboratory, Department of Radiology (Netherlands); Chan, Shaun Xavier Ju Min, E-mail: shaun.xavier.chan@singhealth.com.sg [Singapore General Hospital, Department of Interventional Radiology (Singapore); Leeuwen, Fijs W. B. van, E-mail: F.W.B.van-Leeuwen@lumc.nl [Leiden University Medical Center, Interventional and Molecular Imaging Laboratory, Department of Radiology (Netherlands); Erkel, Arian R. van, E-mail: a.r.van-erkel@lumc.nl [Leiden University Medical Centre, Department of Radiology (Netherlands)

2017-06-15

PurposeTo determine the accuracy of automatic and manual co-registration methods for image fusion of three-dimensional computed tomography (CT) with real-time ultrasonography (US) for image-guided liver interventions.Materials and MethodsCT images of a skills phantom with liver lesions were acquired and co-registered to US using GE Logiq E9 navigation software. Manual co-registration was compared to automatic and semiautomatic co-registration using an active tracker. Also, manual point registration was compared to plane registration with and without an additional translation point. Finally, comparison was made between manual and automatic selection of reference points. In each experiment, accuracy of the co-registration method was determined by measurement of the residual displacement in phantom lesions by two independent observers.ResultsMean displacements for a superficial and deep liver lesion were comparable after manual and semiautomatic co-registration: 2.4 and 2.0 mm versus 2.0 and 2.5 mm, respectively. Both methods were significantly better than automatic co-registration: 5.9 and 5.2 mm residual displacement (p < 0.001; p < 0.01). The accuracy of manual point registration was higher than that of plane registration, the latter being heavily dependent on accurate matching of axial CT and US images by the operator. Automatic reference point selection resulted in significantly lower registration accuracy compared to manual point selection despite lower root-mean-square deviation (RMSD) values.ConclusionThe accuracy of manual and semiautomatic co-registration is better than that of automatic co-registration. For manual co-registration using a plane, choosing the correct plane orientation is an essential first step in the registration process. Automatic reference point selection based on RMSD values is error-prone.

GERTS GQ User's Manual.

Science.gov (United States)

Akiba, Y.; And Others

This user's manual for the simulation program Graphical Evaluation and Review Technique (GERT) GQ contains sections on nodes, branches, program input description and format, and program output, as well as examples. Also included is a programmer's manual which contains information on scheduling, subroutine descriptions, COMMON Variables, and…

Investigation of off-site airborne transport of lead from a superfund removal action site using lead isotope ratios and concentrations

Science.gov (United States)

Pribil, Michael J.; Maddaloni, Mark A.; Staiger, Kimberly; Wilson, Eric; Magriples, Nick; Ali, Mustafa; Santella, Dennis

2014-01-01

Lead (Pb) concentration and Pb isotopic composition of surface and subsurface soil samples were used to investigate the potential for off-site air transport of Pb from a former white Pb processing facility to neighboring residential homes in a six block area on Staten Island, NY. Surface and subsurface soil samples collected on the Jewett White Pb site were found to range from 1.122 to 1.138 for 206Pb/207Pb and 2.393 to 2.411 for 208Pb/207Pb. The off-site surface soil samples collected from residential backyards, train trestle, near site grass patches and background areas varied from 1.144 to 1.196 for 206Pb/207Pb and 2.427 to 2.464 for 208Pb/207Pb. Two soil samples collected along Richmond Terrace, where Jewett site soils accumulated after major rain events, varied from 1.136 to 1.147 for 206Pb/207Pb and 2.407 to 2.419 for 208Pb/207Pb. Lead concentration for on-site surface soil samples ranged from 450 to 8000 ug/g, on-site subsurface soil samples ranged from 90,000 to 240,000 ug/g and off-site samples varied from 380 to 3500 ug/g. Lead concentration and isotopic composition for the Staten Island off-site samples were similar to previously published data for other northeastern US cities and reflect re-suspension and re-mobilization of local accumulated Pb. The considerable differences in both the Pb isotopic composition and Pb concentration of on-site and off-site samples resulted in the ability to geochemically trace the transport of particulate Pb. Data in this study indicate minimal off-site surface transport of Pb from the Jewett site into the neighboring residential area.

The working mechanism of manual therapy in participants with chronic tension-type headache.

Science.gov (United States)

Castien, René; Blankenstein, Annette; van der Windt, Daniëlle; Heymans, Martijn W; Dekker, Joost

2013-10-01

Prospective longitudinal study. To explore the working mechanism of manual therapy, we investigated whether 3 cervical spine variables were mediators of the effect of manual therapy on headache frequency. Background Manual therapy has been shown to reduce headache frequency in participants with chronic tension-type headache (CTTH). To what extent specific elements of treatment contribute to the effectiveness of manual therapy in CTTH is unknown. One hundred eighty-two participants with CTTH participated in a prospective longitudinal study: 142 underwent manual therapy and 40 participants received usual care by their general practitioner. Regression analysis was performed according to the steps described by Baron and Kenny, and the proportion of mediated effect was estimated for 3 potential mediators: (1) cervical range of motion, (2) neck flexor endurance, and (3) forward head posture. Outcome was defined as a 50% or greater reduction in headache days. Neck flexor endurance mediated 24.5% of the effect of manual therapy. Cervical range of motion and forward head posture showed no mediated effect. Increased neck flexor endurance appears to be a working mechanism of manual therapy. This finding supports isometric training of neck flexors in participants with CTTH. Trial registered with Netherlands Trial Register (TR 1074).

Nuclear electronics laboratory manual

International Nuclear Information System (INIS)

1984-05-01

The Nuclear Electronics Laboratory Manual is a joint product of several electronics experts who have been associated with IAEA activity in this field for many years. The manual does not include experiments of a basic nature, such as characteristics of different active electronics components. It starts by introducing small electronics blocks, employing one or more active components. The most demanding exercises instruct a student in the design and construction of complete circuits, as used in commercial nuclear instruments. It is expected that a student who completes all the experiments in the manual should be in a position to design nuclear electronics units and also to understand the functions of advanced commercial instruments which need to be repaired or maintained. The future tasks of nuclear electronics engineers will be increasingly oriented towards designing and building the interfaces between a nuclear experiment and a computer. The manual pays tribute to this development by introducing a number of experiments which illustrate the principles and the technology of interfacing

User's Manual for the New England Water-Use Data System (NEWUDS)

Science.gov (United States)

Horn, Marilee A.

2003-01-01

Water is used in a variety of ways that need to be understood for effective management of water resources. Water-use activities need to be categorized and included in a database management system to understand current water uses and to provide information to water-resource management policy decisionmakers. The New England Water-Use Data System (NEWUDS) is a complex database developed to store water-use information that allows water to be tracked from a point of water-use activity (called a 'Site'), such as withdrawal from a resource (reservoir or aquifer), to a second Site, such as distribution to a user (business or irrigator). NEWUDS conceptual model consists of 10 core entities: system, owner, address, location, site, data source, resource, conveyance, transaction/rate, and alias, with tables available to store user-defined details. Three components--site (with both a From Site and a To Site), a conveyance that connects them, and a transaction/rate associated with the movement of water over a specific time interval form the core of the basic NEWUDS network model. The most important step in correctly translating real-world water-use activities into a storable format in NEWUDS depends on choosing the appropriate sites and linking them correctly in a network to model the flow of water from the initial From Site to the final To Site. Ten water-use networks representing real-world activities are described--three withdrawal networks, three return networks, two user networks, two complex community-system networks. Ten case studies of water use, one for each network, also are included in this manual to illustrate how to compile, store, and retrieve the appropriate data. The sequence of data entry into tables is critical because there are many foreign keys. The recommended core entity sequence is (1) system, (2) owner, (3) address, (4) location, (5) site, (6) data source, (7) resource, (8) conveyance, (9) transaction, and (10) rate; with (11) alias and (12) user

Maintenance Plan for the Performance Assessments and Composite Analyses of the Area 3 and Area 5 Radioactive Waste Management Sites at the Nevada Test Site

International Nuclear Information System (INIS)

Vefa Yucel

2007-01-01

U.S. Department of Energy (DOE) Manual M 435.1-1 requires that performance assessments (PAs) and composite analyses (CAs) for low-level waste (LLW) disposal facilities be maintained by the field offices. This plan describes the activities performed to maintain the PA and the CA for the Area 3 and Area 5 Radioactive Waste Management Sites (RWMSs) at the Nevada Test Site (NTS). This plan supersedes the Maintenance Plan for the Performance Assessments and Composite Analyses for the Area 3 and Area 5 Radioactive Waste Management Sites at the Nevada Test Site (DOE/NV/11718--491-REV 1, dated September 2002). The plan is based on U.S. Department of Energy (DOE) Order 435.1 (DOE, 1999a), DOE Manual M 435.1-1 (DOE, 1999b), the DOE M 435.1-1 Implementation Guide DOE G 435.1-1 (DOE, 1999c), and the Maintenance Guide for PAs and CAs (DOE, 1999d). The plan includes a current update on PA/CA documentation, a revised schedule, and a section on Quality Assurance

Corrective Action Decision Document for Corrective Action Unit 168: Area 25 and 26 Contaminated Materials and Waste Dumps, Nevada Test Site, Nevada, Rev. No.: 2 with Errata Sheet

Energy Technology Data Exchange (ETDEWEB)

Wickline, Alfred

2006-12-01

disposal cells contained within the landfill boundaries. (3) No COCs were identified at CAS 25-19-02. (4) Radiological surveys at CAS 25-23-02 identified 13 railroad cars that exceeded the NV/YMP Radiological Control Manual limits for free release. Six railroad cars were below these limits and therefore met the free-release criteria. (5) An In-Situ Object Counting System survey taken at CAS 25-23-02 identified two railroad cars possibly containing fuel fragments; both exceeded the NV/YMP Radiological Control Manual free release criteria. (6) Corrective Action Site 25-23-18 contains total petroleum hydrocarbons-diesel-range organics, Aroclor-1260, uranium-234, uranium-235, strontium-90, and cesium-137 that exceed PALs. (7) Radiological surveys at CAS 25-34-01 indicate that there were no total contamination readings that exceeded the NV/YMP Radiological Control Manual limits for free release. (8) Radiological surveys at CAS 25-34-02 indicate that there were no total contamination readings that exceeded the NV/YMP Radiological Control Manual limits for free release. (9) Radiological surveys at CAS 25-23-13 identified six pieces of equipment that exceed the NV/YMP Radiological Control Manual limits for free release. (10) Corrective Action Site 25-99-16 was not investigated. A review of historical documentation and current site conditions showed that no further characterization was required to select the appropriate corrective action. (11) Corrective Action Site 26-08-01 contains hydrocarbon-contaminated soil at concentrations exceeding the PAL. The contamination is at discrete locations associated with asphalt debris. (12) Corrective Action Site 26-17-01 contains total petroleum hydrocarbons-diesel-range organics and Aroclor-1260 exceeding the PALs. (13) Radiological surveys at CAS 26-19-02 identified metallic debris that exceeded the NV/YMP Radiological Control Manual limits for free release. Concentrations of radiological or chemical constituents in soil did not exceed PALs.

Impacts of Panicum maximum Jacq. invasion and its manual weeding on the wood plant regeneration in the understory of a restoration site Efeitos da invasão por Panicum maximum Jacq. e do seu controle manual sobre a regeneração de plantas lenhosas no sub-bosque de um reflorestamento

Directory of Open Access Journals (Sweden)

Gabriela Ribeiro de Andrade

2012-06-01

Full Text Available Responsible for considerable annual losses of biodiversity in natural ecosystems, invasive alien species cause important conservation problems, leading native species to local extinction. This study examined the relationship among the coverage of Guinea-grass (Panicum maximum Jacq., its manual weeding and the woody plant diversity of a restoration site. The site is a reforestation created using native species but due to spacing and species composition grass still dominates its understory more than 17 years after. Preliminary results showed that it is a barrier to the establishment of native species. In this study, we established 20 plots of 5m x 5m divided into two treatments, control and removal of P. maximum, to investigate the impact of manual weeding on the understory in a period of 90 days. Grass cover and canopy openness were also recorded. The grass cover had negative correlation with the abundance of plants, with the species richness and abundance of tree species. Canopy openness had a negative influence on the species richness, on abundance and richness of tree species, but not showed correlation with P. maximum. After grass removal, both abundance of seedling and species richness had no significant differences, so the manual weeding did not cause a negative impact in short time on the regeneration of the understory due to accidental native plant uprooting. However, a positive impact is expected only after a longer period of observation, after successive removals of invasive herbaceous and increased chance of colonization of the area by regenerating seedlings.Responsáveis por perdas anuais consideráveis na biodiversidade dos ecossistemas naturais, as espécies exóticas invasoras causam sérios problemas à conservação, levando muitas espécies à extinção local. Este estudo analisou o efeito da cobertura de capim-colonião (Panicum maximum Jacq. no sub-bosque de um reflorestamento dominado há mais de 17 anos por essa gram

14 CFR 121.141 - Airplane flight manual.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplane flight manual. 121.141 Section 121... REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Manual Requirements § 121.141 Airplane flight manual. (a) Each certificate holder shall keep a current approved airplane flight manual for each type of...

Geological and geophysical investigations in the selection and characterization of the disposal site for high-level nuclear waste in Finland

Energy Technology Data Exchange (ETDEWEB)

Paulamaki, S.; Paananen, M.; Kuivamaki, A. [Geological Survey of Finland, Espoo (Finland); Wikstrom, L. [Posiva Oy, Olkiluoto (Finland)], e-mail: seppo.paulamaki@gtk.fi

2011-07-01

Two power companies, Teollisuuden Voima Oy (TVO) and Fortum Power and Heat Oy, are preparing for the final disposal of spent nuclear fuel deep in the Finnish bedrock. In the initial phase of the site selection process in the late 1970s and early 1980s, the Geological Survey of Finland (GTK) examined the general bedrock factors that would have to be taken into account in connection with final disposal with reference to the international guidelines adapted to Finnish conditions. On the basis of extensive basic research data, it was concluded that it is possible to find a potential disposal site that fulfils the geological safety criteria. In the subsequent site selection survey covering the whole of Finland, carried out by GTK in 1983-1985, 101 potential investigation areas were discovered. Eventually, five areas were selected by TVO for preliminary site investigations: Romuvaara and Veitsivaara in the Archaean basement complex, Kivetty and Syyry in the Proterozoic granitoid area, and Olkiluoto (TVO's NPP site) in the Proterozoic migmatite area. The preliminary site investigations at the selected sites in 1987-1992 comprised deep drillings together with geological, geophysical, hydrogeological and hydrogeochemical investigations. A conceptual geological bedrock model was constructed for each site, including lithology, fracturing, fracture zones and hydrogeological conditions. On the basis of preliminary site investigations, TVO selected Romuvaara, Kivetty and Olkiluoto for detailed site investigations to be carried out during 1993-2000. After the feasibility studies, the island of Haestholmen, where Fortum's Loviisa nuclear power plant is located, was added to the list of potential disposal sites. In the detailed site investigations, additional data on bedrock were gathered, the previous conceptual geological, hydrogeological and hydrogeochemical models were complemented, the rock mechanical properties of the bedrock were examined, and the constructability

Geological and geophysical investigations in the selection and characterization of the disposal site for high-level nuclear waste in Finland

Energy Technology Data Exchange (ETDEWEB)

Paulamaki, S; Paananen, M; Kuivamaki, A [Geological Survey of Finland, Espoo (Finland); Wikstrom, L. [Posiva Oy, Olkiluoto (Finland)], e-mail: seppo.paulamaki@gtk.fi

2011-07-01

Two power companies, Teollisuuden Voima Oy (TVO) and Fortum Power and Heat Oy, are preparing for the final disposal of spent nuclear fuel deep in the Finnish bedrock. In the initial phase of the site selection process in the late 1970s and early 1980s, the Geological Survey of Finland (GTK) examined the general bedrock factors that would have to be taken into account in connection with final disposal with reference to the international guidelines adapted to Finnish conditions. On the basis of extensive basic research data, it was concluded that it is possible to find a potential disposal site that fulfils the geological safety criteria. In the subsequent site selection survey covering the whole of Finland, carried out by GTK in 1983-1985, 101 potential investigation areas were discovered. Eventually, five areas were selected by TVO for preliminary site investigations: Romuvaara and Veitsivaara in the Archaean basement complex, Kivetty and Syyry in the Proterozoic granitoid area, and Olkiluoto (TVO's NPP site) in the Proterozoic migmatite area. The preliminary site investigations at the selected sites in 1987-1992 comprised deep drillings together with geological, geophysical, hydrogeological and hydrogeochemical investigations. A conceptual geological bedrock model was constructed for each site, including lithology, fracturing, fracture zones and hydrogeological conditions. On the basis of preliminary site investigations, TVO selected Romuvaara, Kivetty and Olkiluoto for detailed site investigations to be carried out during 1993-2000. After the feasibility studies, the island of Haestholmen, where Fortum's Loviisa nuclear power plant is located, was added to the list of potential disposal sites. In the detailed site investigations, additional data on bedrock were gathered, the previous conceptual geological, hydrogeological and hydrogeochemical models were complemented, the rock mechanical properties of the bedrock were examined, and the constructability and the

Investigation of the metal binding site in methionine aminopeptidase by density functional theory

DEFF Research Database (Denmark)

Jørgensen, Anne Techau; Norrby, Per-Ola; Liljefors, Tommy

2002-01-01

All methionine aminopeptidases exhibit the same conserved metal binding site. The structure of this site with either Co2+ ions or Zn2+ ions was investigated using density functional theory. The calculations showed that the structure of the site was not influenced by the identity of the metal ions....... This was the case for both of the systems studied; one based on the X-ray structure of the human methionine aminopeptidase type 2 (hMetAP-2) and the other based on the X-ray structure of the E. coli methionine aminopeptidase type 1 (eMetAP-1). Another important structural issue is the identity of the bridging...

Hanford site past practice investigation strategy: Lessons learned

International Nuclear Information System (INIS)

Thompson, K. Michael

1992-01-01

The U. S. Department of Energy (DOE), U. S. Environmental Protection Agency (EPA), and the Washington State Department of Ecology (Ecology) have negotiated a strategy for performing Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and Resource Conservation and Recovery Act (RCRA) Past Practice investigations in a more streamlined manner with a bias-for-action. This strategy provides new concepts for 1) accelerating decision-making by maximizing the use of existing data consistent with data quality objectives and 2) undertaking expedited response actions and/or interim remedial measures as appropriate to either remove threats to human health and welfare and the environment or to reduce risk by reducing toxicity, mobility or volume of contaminants. Since the goal of the program is cleanup, much more emphasis will be placed on initiating and completing waste site cleanups through interim measures. While investigations and studies are important in meeting long-range goals, there is now agreement by the parties that an appropriate and significant portion of the near-term funding resources can and should be dedicated to remedial work, where there is sufficient information from which to plan and implement interim remedial measures. The initial stages of Hanford clean-up will optimize the use of interim cleanup actions when justified and practicable. Existing data will be evaluated as the initial basis for decision-making. If the data are found to be insufficient, additional essential data will be collected to support the IRM in a limited field investigation (LFI). Only data needed to formulate a conceptual model (source to pathway to receptor) and qualitative risk assessment would be obtained. The data quality objectives of the LFI will be established based on the use of the data in deciding on IRMs. The data might not need to be of the same quality needed to support final RODs, since the IRM itself would yield valuable information for

Oil Spill Response Manual

NARCIS (Netherlands)

Marieke Zeinstra; Sandra Heins; Wierd Koops

2014-01-01

A two year programme has been carried out by the NHL University of Applied Sciences together with private companies in the field of oil and chemical spill response to finalize these manuals on oil and chemical spill response. These manuals give a good overview of all aspects of oil and chemical

The Combined Effect of Cold and Moisture on Manual Performance.

Science.gov (United States)

Ray, Matthew; Sanli, Elizabeth; Brown, Robert; Ennis, Kerri Ann; Carnahan, Heather

2018-02-01

Objective The aim of this study was to investigate the combined effect of cold and moisture on manual performance and tactile sensitivity. Background People working in the ocean environment often perform manual work in cold and wet conditions. Although the independent effects of cold and moisture on hand function are known, their combined effect has not been investigated. Method Participants completed sensory (Touch-Test, two-point discrimination) and motor (Purdue Pegboard, Grooved Pegboard, reef knot untying) tests in the following conditions: dry hand, wet hand, cold hand, and cold and wet hand. Results For the Purdue Pegboard and knot untying tasks, the greatest decrement in performance was observed in the cold-and-wet-hand condition, whereas the decrements seen in the cold-hand and wet-hand conditions were similar. In the Grooved Pegboard task, the performance decrements exhibited in the cold-and-wet-hand condition and the cold-hand condition were similar, whereas no decrement was observed in the wet-hand condition. Tactile sensitivity was reduced in the cold conditions for the Touch-Test but not the two-point discrimination test. The combined effect of cold and moisture led to the largest performance decrements except when intrinsic object properties helped with grasp maintenance. The independent effects of cold and moisture on manual performance were comparable. Application Tools and equipment for use in the cold ocean environment should be designed to minimize the effects of cold and moisture on manual performance by including object properties that enhance grasp maintenance and minimize the fine-dexterity requirements.

Comparison of Manual Mapping and Automated Object-Based Image Analysis of Non-Submerged Aquatic Vegetation from Very-High-Resolution UAS Images

Directory of Open Access Journals (Sweden)

Eva Husson

2016-09-01

Full Text Available Aquatic vegetation has important ecological and regulatory functions and should be monitored in order to detect ecosystem changes. Field data collection is often costly and time-consuming; remote sensing with unmanned aircraft systems (UASs provides aerial images with sub-decimetre resolution and offers a potential data source for vegetation mapping. In a manual mapping approach, UAS true-colour images with 5-cm-resolution pixels allowed for the identification of non-submerged aquatic vegetation at the species level. However, manual mapping is labour-intensive, and while automated classification methods are available, they have rarely been evaluated for aquatic vegetation, particularly at the scale of individual vegetation stands. We evaluated classification accuracy and time-efficiency for mapping non-submerged aquatic vegetation at three levels of detail at five test sites (100 m × 100 m differing in vegetation complexity. We used object-based image analysis and tested two classification methods (threshold classification and Random Forest using eCognition®. The automated classification results were compared to results from manual mapping. Using threshold classification, overall accuracy at the five test sites ranged from 93% to 99% for the water-versus-vegetation level and from 62% to 90% for the growth-form level. Using Random Forest classification, overall accuracy ranged from 56% to 94% for the growth-form level and from 52% to 75% for the dominant-taxon level. Overall classification accuracy decreased with increasing vegetation complexity. In test sites with more complex vegetation, automated classification was more time-efficient than manual mapping. This study demonstrated that automated classification of non-submerged aquatic vegetation from true-colour UAS images was feasible, indicating good potential for operative mapping of aquatic vegetation. When choosing the preferred mapping method (manual versus automated the desired level of

Confined Site Construction: A qualitative investigation of critical issues affecting management of Health and Safety

OpenAIRE

Spillane, John P.; Oyedele, Lukumon O.; Von Meding, Jason; Konanahalli, Ashwini; Jaiyeoba, Babatunde E.; Tijani, Iyabo K.

2011-01-01

The construction industry is inherently risky, with a significant number of accidents and disasters occurring, particularly on confined construction sites. This research investigates and identifies the various issues affecting successful management of health and safety in confined construction sites. The rationale is that identifying the issues would assist the management of health and safety particularly in inner city centres which are mostly confined sites. Using empiricism epistemology, th...

46 CFR 160.176-21 - User manuals.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false User manuals. 160.176-21 Section 160.176-21 Shipping...: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Inflatable Lifejackets § 160.176-21 User manuals. (a) The manufacturer must develop a user's manual for each model of inflatable lifejacket. The content of the manual...