WorldWideScience

Sample records for site descriptive modelling

  1. Site descriptive modelling - strategy for integrated evaluation

    International Nuclear Information System (INIS)

    Andersson, Johan

    2003-02-01

    The current document establishes the strategy to be used for achieving sufficient integration between disciplines in producing Site Descriptive Models during the Site Investigation stage. The Site Descriptive Model should be a multidisciplinary interpretation of geology, rock mechanics, thermal properties, hydrogeology, hydrogeochemistry, transport properties and ecosystems using site investigation data from deep bore holes and from the surface as input. The modelling comprise the following iterative steps, evaluation of primary data, descriptive and quantitative modelling (in 3D), overall confidence evaluation. Data are first evaluated within each discipline and then the evaluations are checked between the disciplines. Three-dimensional modelling (i.e. estimating the distribution of parameter values in space and its uncertainty) is made in a sequence, where the geometrical framework is taken from the geological model and in turn used by the rock mechanics, thermal and hydrogeological modelling etc. The three-dimensional description should present the parameters with their spatial variability over a relevant and specified scale, with the uncertainty included in this description. Different alternative descriptions may be required. After the individual discipline modelling and uncertainty assessment a phase of overall confidence evaluation follows. Relevant parts of the different modelling teams assess the suggested uncertainties and evaluate the feedback. These discussions should assess overall confidence by, checking that all relevant data are used, checking that information in past model versions is considered, checking that the different kinds of uncertainty are addressed, checking if suggested alternatives make sense and if there is potential for additional alternatives, and by discussing, if appropriate, how additional measurements (i.e. more data) would affect confidence. The findings as well as the modelling results are to be documented in a Site Description

  2. Forsmark - site descriptive model version 0

    International Nuclear Information System (INIS)

    2002-10-01

    During 2002, the Swedish Nuclear Fuel and Waste Management Company (SKB) is starting investigations at two potential sites for a deep repository in the Precambrian basement of the Fennoscandian Shield. The present report concerns one of those sites, Forsmark, which lies in the municipality of Oesthammar, on the east coast of Sweden, about 150 kilometres north of Stockholm. The site description should present all collected data and interpreted parameters of importance for the overall scientific understanding of the site, for the technical design and environmental impact assessment of the deep repository, and for the assessment of long-term safety. The site description will have two main components: a written synthesis of the site, summarising the current state of knowledge, as documented in the databases containing the primary data from the site investigations, and one or several site descriptive models, in which the collected information is interpreted and presented in a form which can be used in numerical models for rock engineering, environmental impact and long-term safety assessments. The site descriptive models are devised and stepwise updated as the site investigations proceed. The point of departure for this process is the regional site descriptive model, version 0, which is the subject of the present report. Version 0 is developed out of the information available at the start of the site investigation. This information, with the exception of data from tunnels and drill holes at the sites of the Forsmark nuclear reactors and the underground low-middle active radioactive waste storage facility, SFR, is mainly 2D in nature (surface data), and is general and regional, rather than site-specific, in content. For this reason, the Forsmark site descriptive model, version 0, as detailed in the present report, has been developed at a regional scale. It covers a rectangular area, 15 km in a southwest-northeast and 11 km in a northwest-southeast direction, around the

  3. Simpevarp - site descriptive model version 0

    International Nuclear Information System (INIS)

    2002-11-01

    During 2002, SKB is starting detailed investigations at two potential sites for a deep repository in the Precambrian rocks of the Fennoscandian Shield. The present report concerns one of those sites, Simpevarp, which lies in the municipality of Oskarshamn, on the southeast coast of Sweden, about 250 kilometres south of Stockholm. The site description will have two main components: a written synthesis of the site, summarising the current state of knowledge, as documented in the databases containing the primary data from the site investigations, and one or several site descriptive models, in which the collected information is interpreted and presented in a form which can be used in numerical models for rock engineering, environmental impact and long-term safety assessments. SKB maintains two main databases at the present time, a site characterisation database called SICADA and a geographic information system called SKB GIS. The site descriptive model will be developed and presented with the aid of the SKB GIS capabilities, and with SKBs Rock Visualisation System (RVS), which is also linked to SICADA. The version 0 model forms an important framework for subsequent model versions, which are developed successively, as new information from the site investigations becomes available. Version 0 is developed out of the information available at the start of the site investigation. In the case of Simpevarp, this is essentially the information which was compiled for the Oskarshamn feasibility study, which led to the choice of that area as a favourable object for further study, together with information collected since its completion. This information, with the exception of the extensive data base from the nearby Aespoe Hard Rock Laboratory, is mainly 2D in nature (surface data), and is general and regional, rather than site-specific, in content. Against this background, the present report consists of the following components: an overview of the present content of the databases

  4. Simpevarp - site descriptive model version 0

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-11-01

    During 2002, SKB is starting detailed investigations at two potential sites for a deep repository in the Precambrian rocks of the Fennoscandian Shield. The present report concerns one of those sites, Simpevarp, which lies in the municipality of Oskarshamn, on the southeast coast of Sweden, about 250 kilometres south of Stockholm. The site description will have two main components: a written synthesis of the site, summarising the current state of knowledge, as documented in the databases containing the primary data from the site investigations, and one or several site descriptive models, in which the collected information is interpreted and presented in a form which can be used in numerical models for rock engineering, environmental impact and long-term safety assessments. SKB maintains two main databases at the present time, a site characterisation database called SICADA and a geographic information system called SKB GIS. The site descriptive model will be developed and presented with the aid of the SKB GIS capabilities, and with SKBs Rock Visualisation System (RVS), which is also linked to SICADA. The version 0 model forms an important framework for subsequent model versions, which are developed successively, as new information from the site investigations becomes available. Version 0 is developed out of the information available at the start of the site investigation. In the case of Simpevarp, this is essentially the information which was compiled for the Oskarshamn feasibility study, which led to the choice of that area as a favourable object for further study, together with information collected since its completion. This information, with the exception of the extensive data base from the nearby Aespoe Hard Rock Laboratory, is mainly 2D in nature (surface data), and is general and regional, rather than site-specific, in content. Against this background, the present report consists of the following components: an overview of the present content of the databases

  5. Forsmark - site descriptive model version 0

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-10-01

    During 2002, the Swedish Nuclear Fuel and Waste Management Company (SKB) is starting investigations at two potential sites for a deep repository in the Precambrian basement of the Fennoscandian Shield. The present report concerns one of those sites, Forsmark, which lies in the municipality of Oesthammar, on the east coast of Sweden, about 150 kilometres north of Stockholm. The site description should present all collected data and interpreted parameters of importance for the overall scientific understanding of the site, for the technical design and environmental impact assessment of the deep repository, and for the assessment of long-term safety. The site description will have two main components: a written synthesis of the site, summarising the current state of knowledge, as documented in the databases containing the primary data from the site investigations, and one or several site descriptive models, in which the collected information is interpreted and presented in a form which can be used in numerical models for rock engineering, environmental impact and long-term safety assessments. The site descriptive models are devised and stepwise updated as the site investigations proceed. The point of departure for this process is the regional site descriptive model, version 0, which is the subject of the present report. Version 0 is developed out of the information available at the start of the site investigation. This information, with the exception of data from tunnels and drill holes at the sites of the Forsmark nuclear reactors and the underground low-middle active radioactive waste storage facility, SFR, is mainly 2D in nature (surface data), and is general and regional, rather than site-specific, in content. For this reason, the Forsmark site descriptive model, version 0, as detailed in the present report, has been developed at a regional scale. It covers a rectangular area, 15 km in a southwest-northeast and 11 km in a northwest-southeast direction, around the

  6. Confidence assessment. Site-descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    2009-06-01

    The objective of this report is to assess the confidence that can be placed in the Laxemar site descriptive model, based on the information available at the conclusion of the surface-based investigations (SDM-Site Laxemar). In this exploration, an overriding question is whether remaining uncertainties are significant for repository engineering design or long-term safety assessment and could successfully be further reduced by more surface-based investigations or more usefully by explorations underground made during construction of the repository. Procedures for this assessment have been progressively refined during the course of the site descriptive modelling, and applied to all previous versions of the Forsmark and Laxemar site descriptive models. They include assessment of whether all relevant data have been considered and understood, identification of the main uncertainties and their causes, possible alternative models and their handling, and consistency between disciplines. The assessment then forms the basis for an overall confidence statement. The confidence in the Laxemar site descriptive model, based on the data available at the conclusion of the surface based site investigations, has been assessed by exploring: - Confidence in the site characterization data base, - remaining issues and their handling, - handling of alternatives, - consistency between disciplines and - main reasons for confidence and lack of confidence in the model. Generally, the site investigation database is of high quality, as assured by the quality procedures applied. It is judged that the Laxemar site descriptive model has an overall high level of confidence. Because of the relatively robust geological model that describes the site, the overall confidence in the Laxemar Site Descriptive model is judged to be high, even though details of the spatial variability remain unknown. The overall reason for this confidence is the wide spatial distribution of the data and the consistency between

  7. Confidence assessment. Site-descriptive modelling SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    2008-12-15

    The objective of this report is to assess the confidence that can be placed in the Laxemar site descriptive model, based on the information available at the conclusion of the surface-based investigations (SDM-Site Laxemar). In this exploration, an overriding question is whether remaining uncertainties are significant for repository engineering design or long-term safety assessment and could successfully be further reduced by more surface-based investigations or more usefully by explorations underground made during construction of the repository. Procedures for this assessment have been progressively refined during the course of the site descriptive modelling, and applied to all previous versions of the Forsmark and Laxemar site descriptive models. They include assessment of whether all relevant data have been considered and understood, identification of the main uncertainties and their causes, possible alternative models and their handling, and consistency between disciplines. The assessment then forms the basis for an overall confidence statement. The confidence in the Laxemar site descriptive model, based on the data available at the conclusion of the surface based site investigations, has been assessed by exploring: - Confidence in the site characterization data base, - remaining issues and their handling, - handling of alternatives, - consistency between disciplines and - main reasons for confidence and lack of confidence in the model. Generally, the site investigation database is of high quality, as assured by the quality procedures applied. It is judged that the Laxemar site descriptive model has an overall high level of confidence. Because of the relatively robust geological model that describes the site, the overall confidence in the Laxemar Site Descriptive model is judged to be high, even though details of the spatial variability remain unknown. The overall reason for this confidence is the wide spatial distribution of the data and the consistency between

  8. Transport properties site descriptive model. Guidelines for evaluation and modelling

    International Nuclear Information System (INIS)

    Berglund, Sten; Selroos, Jan-Olof

    2004-04-01

    This report describes a strategy for the development of Transport Properties Site Descriptive Models within the SKB Site Investigation programme. Similar reports have been produced for the other disciplines in the site descriptive modelling (Geology, Hydrogeology, Hydrogeochemistry, Rock mechanics, Thermal properties, and Surface ecosystems). These reports are intended to guide the site descriptive modelling, but also to provide the authorities with an overview of modelling work that will be performed. The site descriptive modelling of transport properties is presented in this report and in the associated 'Strategy for the use of laboratory methods in the site investigations programme for the transport properties of the rock', which describes laboratory measurements and data evaluations. Specifically, the objectives of the present report are to: Present a description that gives an overview of the strategy for developing Site Descriptive Models, and which sets the transport modelling into this general context. Provide a structure for developing Transport Properties Site Descriptive Models that facilitates efficient modelling and comparisons between different sites. Provide guidelines on specific modelling issues where methodological consistency is judged to be of special importance, or where there is no general consensus on the modelling approach. The objectives of the site descriptive modelling process and the resulting Transport Properties Site Descriptive Models are to: Provide transport parameters for Safety Assessment. Describe the geoscientific basis for the transport model, including the qualitative and quantitative data that are of importance for the assessment of uncertainties and confidence in the transport description, and for the understanding of the processes at the sites. Provide transport parameters for use within other discipline-specific programmes. Contribute to the integrated evaluation of the investigated sites. The site descriptive modelling of

  9. Bedrock hydrogeology Forsmark. Site descriptive modelling, SDM-Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Follin, Sven (SF GeoLogic AB, Taeby (Sweden))

    2008-12-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) has conducted site investigations at two different locations, the Forsmark and Laxemar-Simpevarp areas, with the objective of siting a final repository for spent nuclear fuel according to the KBS-3 concept. Site characterisation should provide all data required for an integrated evaluation of the suitability of the investigated site and an important component in the characterisation work is the development of a hydrogeological model. The hydrogeological model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It also provides input to the safety assessment. Another important use of the hydrogeological model is in the environmental impact assessment. This report presents the understanding of the hydrogeological conditions of the bedrock at Forsmark reached following the completion of the surface-based investigations and provides a summary of the bedrock hydrogeological model and the underlying data supporting its development. It constitutes the main reference on bedrock hydrogeology for the site descriptive model concluding the surface-based investigations at Forsmark, SDM-site, and is intended to describe the hydraulic properties and hydrogeological conditions of the bedrock at the site and to give the information essential for demonstrating understanding

  10. Confidence assessment. Site descriptive modelling SDM-Site Forsmark

    International Nuclear Information System (INIS)

    2008-09-01

    The objective of this report is to assess the confidence that can be placed in the Forsmark site descriptive model, based on the information available at the conclusion of the surface-based investigations (SDM-Site Forsmark). In this exploration, an overriding question is whether remaining uncertainties are significant for repository engineering design or long-term safety assessment and could successfully be further reduced by more surface based investigations or more usefully by explorations underground made during construction of the repository. The confidence in the Forsmark site descriptive model, based on the data available at the conclusion of the surface-based site investigations, have been assessed by exploring: Confidence in the site characterisation data base; Key remaining issues and their handling; Handling of alternative models; Consistency between disciplines; and, Main reasons for confidence and lack of confidence in the model. It is generally found that the key aspects of importance for safety assessment and repository engineering of the Forsmark site descriptive model are associated with a high degree of confidence. Because of the robust geological model that describes the site, the overall confidence in Forsmark site descriptive model is judged to be high. While some aspects have lower confidence this lack of confidence is handled by providing wider uncertainty ranges, bounding estimates and/or alternative models. Most, but not all, of the low confidence aspects have little impact on repository engineering design or for long-term safety. Poor precision in the measured data are judged to have limited impact on uncertainties on the site descriptive model, with the exceptions of inaccuracy in determining the position of some boreholes at depth in 3-D space, as well as the poor precision of the orientation of BIPS images in some boreholes, and the poor precision of stress data determined by overcoring at the locations where the pre

  11. Site investigations: Strategy for rock mechanics site descriptive model

    International Nuclear Information System (INIS)

    Andersson, Johan; Christiansson, Rolf; Hudson, John

    2002-05-01

    As a part of the planning work for the Site Investigations, SKB has developed a Rock Mechanics Site Descriptive Modelling Strategy. Similar strategies are being developed for other disciplines. The objective of the strategy is that it should guide the practical implementation of evaluating site specific data during the Site Investigations. It is also understood that further development may be needed. This methodology enables the crystalline rock mass to be characterised in terms of the quality at different sites, for considering rock engineering constructability, and for providing the input to numerical models and performance assessment calculations. The model describes the initial stresses and the distribution of deformation and strength properties of the intact rock, of fractures and fracture zones, and of the rock mass. The rock mass mechanical properties are estimated by empirical relations and by numerical simulations. The methodology is based on estimation of mechanical properties using both empirical and heroretical/numerical approaches; and estimation of in situ rock stress using judgement and numerical modelling, including the influence of fracture zones. These approaches are initially used separately, and then combined to produce the required characterisation estimates. The methodology was evaluated with a Test Case at the Aespoe Hard Rock Laboratory in Sweden. The quality control aspects are an important feature of the methodology: these include Protocols to ensure the structure and coherence of the procedures used, regular meetings to enhance communication, feedback from internal and external reviewing, plus the recording of an audit trail of the development steps and decisions made. The strategy will be reviewed and, if required, updated as appropriate

  12. Site investigations: Strategy for rock mechanics site descriptive model

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Johan [JA Streamflow AB, Aelvsjoe (Sweden); Christiansson, Rolf [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Hudson, John [Rock Engineering Consultants, Welwyn Garden City (United Kingdom)

    2002-05-01

    As a part of the planning work for the Site Investigations, SKB has developed a Rock Mechanics Site Descriptive Modelling Strategy. Similar strategies are being developed for other disciplines. The objective of the strategy is that it should guide the practical implementation of evaluating site specific data during the Site Investigations. It is also understood that further development may be needed. This methodology enables the crystalline rock mass to be characterised in terms of the quality at different sites, for considering rock engineering constructability, and for providing the input to numerical models and performance assessment calculations. The model describes the initial stresses and the distribution of deformation and strength properties of the intact rock, of fractures and fracture zones, and of the rock mass. The rock mass mechanical properties are estimated by empirical relations and by numerical simulations. The methodology is based on estimation of mechanical properties using both empirical and heroretical/numerical approaches; and estimation of in situ rock stress using judgement and numerical modelling, including the influence of fracture zones. These approaches are initially used separately, and then combined to produce the required characterisation estimates. The methodology was evaluated with a Test Case at the Aespoe Hard Rock Laboratory in Sweden. The quality control aspects are an important feature of the methodology: these include Protocols to ensure the structure and coherence of the procedures used, regular meetings to enhance communication, feedback from internal and external reviewing, plus the recording of an audit trail of the development steps and decisions made. The strategy will be reviewed and, if required, updated as appropriate.

  13. Bedrock hydrogeochemistry Forsmark. Site descriptive modelling SDM-Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Laaksoharju, Marcus [Geopoint AB, Sollentuna (Sweden); Smellie, John [Conterra AB, Partille (Sweden); Tullborg, Eva-Lena [Terralogica, Graabo (Sweden); Gimeno, Maria [Univ. of Zaragoza, Zaragoza (Spain); Hallbeck, Lotta [Microbial Analytics, Goeteborg (Sweden); Molinero, Jorge [Amphos XXI Consulting S.L., Barcelona (Spain); Waber, Nick [Univ. of Bern, Bern (Switzerland)

    2008-12-15

    The overall objectives of the hydrogeochemical site description for Forsmark are to establish a detailed understanding of the hydrogeochemical conditions at the site, and to use this understanding to develop models that address the needs identified by the safety assessment groups during the site investigation phase. Issues of concern to safety assessment are radionuclide transport and technical barrier behaviour, both of which are dependent on the chemistry of groundwater and porewater and their evolution with time. The specific aims of the hydrogeochemical work were: To document the hydrogeochemistry at the Forsmark site with focus on the development of conceptual models to describe and visualise the site. To provide relevant parameter values to be used for safety assessment calculations. To provide the hydrogeochemical basis for the modelling work by other teams, in particular hydrogeology. To take account of the feedback from the SR-Can safety assessment work that bears relevance to the hydrogeochemical modelling work. The work has involved the development of descriptive and mathematical models for groundwaters in relation to rock domains, fracture domains and deformation zones. In this report, the groundwaters have been interpreted in relation to their origin, evolution and composition, which require close integration with geological, climatological and hydrogeological information. Past climate changes are one of the major driving forces for long-term hydrogeochemical changes (hundreds to thousands of years) and are, therefore, of fundamental importance for understanding the palaeohydrogeological, palaeohydrogeochemical and present evolution of groundwater in the Fennoscandian crystalline bedrock. In contrast, redox buffer capacity of the bedrock will minimise the effects on changes in alkalinity and redox at repository depths, therefore limiting the variations in pH and Eh significantly, regardless of major changes in groundwater composition. There is

  14. Bedrock hydrogeochemistry Forsmark. Site descriptive modelling SDM-Site Forsmark

    International Nuclear Information System (INIS)

    Laaksoharju, Marcus; Smellie, John; Tullborg, Eva-Lena; Gimeno, Maria; Hallbeck, Lotta; Molinero, Jorge; Waber, Nick

    2008-12-01

    The overall objectives of the hydrogeochemical site description for Forsmark are to establish a detailed understanding of the hydrogeochemical conditions at the site, and to use this understanding to develop models that address the needs identified by the safety assessment groups during the site investigation phase. Issues of concern to safety assessment are radionuclide transport and technical barrier behaviour, both of which are dependent on the chemistry of groundwater and porewater and their evolution with time. The specific aims of the hydrogeochemical work were: To document the hydrogeochemistry at the Forsmark site with focus on the development of conceptual models to describe and visualise the site. To provide relevant parameter values to be used for safety assessment calculations. To provide the hydrogeochemical basis for the modelling work by other teams, in particular hydrogeology. To take account of the feedback from the SR-Can safety assessment work that bears relevance to the hydrogeochemical modelling work. The work has involved the development of descriptive and mathematical models for groundwaters in relation to rock domains, fracture domains and deformation zones. In this report, the groundwaters have been interpreted in relation to their origin, evolution and composition, which require close integration with geological, climatological and hydrogeological information. Past climate changes are one of the major driving forces for long-term hydrogeochemical changes (hundreds to thousands of years) and are, therefore, of fundamental importance for understanding the palaeohydrogeological, palaeohydrogeochemical and present evolution of groundwater in the Fennoscandian crystalline bedrock. In contrast, redox buffer capacity of the bedrock will minimise the effects on changes in alkalinity and redox at repository depths, therefore limiting the variations in pH and Eh significantly, regardless of major changes in groundwater composition. There is

  15. Surface system Forsmark. Site descriptive modelling SDM-Site Forsmark

    International Nuclear Information System (INIS)

    Lindborg, Tobias

    2008-12-01

    SKB has undertaken site characterization of two different areas, Forsmark and Laxemar-Simpevarp, in order to find a suitable location for a geological repository for spent nuclear fuel. This report focuses on the site descriptive modelling of the surface system at Forsmark. The characterization of the surface system at the site was primarily made by identifying and describing important properties in different parts of the surface system, properties concerning e.g. hydrology and climate, Quaternary deposits and soils, hydrochemistry, vegetation, ecosystem functions, but also current and historical land use. The report presents available input data, methodology for data evaluation and modelling, and resulting models for each of the different disciplines. Results from the modelling of the surface system are also integrated with results from modelling of the deep bedrock system. The Forsmark site is located within the municipality of Oesthammar, about 120 km north of Stockholm. The investigated area is located along the shoreline of Oeregrundsgrepen, a funnel-shaped bay of the Baltic Sea. The area is characterized by small-scale topographic variations and is almost entirely located at altitudes lower than 20 metres above sea level. The Quaternary deposits in the area are dominated by till, characterized by a rich content of calcite which was transported by the glacier ice to the area from the sedimentary bedrock of Gaevlebukten about 100 km north of Forsmark. As a result, the surface waters and shallow groundwater at Forsmark are characterized by high pH values and high concentrations of certain major constituents, especially calcium and bicarbonate. The annual precipitation and runoff are 560 and 150 mm, respectively. The lakes are small and shallow, with mean and maximum depths ranging from approximately 0.1 to 1 m and 0.4 to 2 m. Sea water flows into the most low-lying lakes during events giving rise to very high sea levels. Wetlands are frequent and cover 25 to 35

  16. Geology Laxemar. Site descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Wahlgren, Carl-Henric; Curtis, Philip; Hermanson, Jan; Forssberg, Ola; Oehman, Johan; Fox, Aaron; La Pointe, Paul; Drake, Henrik; Triumf, Carl-Axel; Mattsson, Haakan; Thunehed, Hans; Juhlin, Christopher

    2008-11-01

    The geological work during the SDM Site Laxemar modelling stage has involved the continued development of deterministic models for rock domains (RSM) and deformation zones (ZSM), the identification and deterministic modelling of fracture domains (FSM), and the development of statistical models for fractures and minor deformation zones (geological discrete fracture network (DFN) modelling). The geological DFN model addresses fractures/structures with a size of less than 1 km, which is the lower cut-off of structures included in the deterministic modelling of deformation zones. In order to take account of variability in data resolution, deterministic models for rock domains and deformation zones are presented in both regional and local scale model volumes, while the geological DFN model is valid only within specific fracture domains inside the Laxemar local model volume. The geological and geophysical data that constitute the basis for the SDM-Site Laxemar modelling work comprise all data that have been acquired from Laxemar, i.e. all data that were available at the data freeze for SDM-Site Laxemar at August 31, 2007. Selected quality controlled data from the complementary cored borehole KLX27A have also been utilised in the modelling work. Data from the following investigations were acquired during the complete site investigation between the data freezes for Laxemar 1.2 and SDM-Site Laxemar as defined above: A revised bedrock geological map at the ground surface. Geological and geophysical data from 40 new cored boreholes and 14 percussion boreholes. Sampling and subsequent modal and geochemical analytical work of bedrock samples taken in connection with excavations in southern Laxemar. Detailed mapping of fractures and rock units along 10 trench excavations and 2 large surface exposures (drill sites for KLX09 and KLX11A/KLX20A). Special studies involving more detailed characterisation of deformation zones identified in the geological single-hole interpretation

  17. Geology Laxemar. Site descriptive modelling SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Wahlgren, Carl-Henric (Geological Survey of Sweden, Uppsala (Sweden)); Curtis, Philip; Hermanson, Jan; Forssberg, Ola; Oehman, Johan (Golder Associates AB (Sweden)); Fox, Aaron; La Pointe, Paul (Golder Associates Inc (United States)); Drake, Henrik (Dept. of Earth Sciences, Univ. of Goeteborg, Goeteborg (Sweden)); Triumf, Carl-Axel; Mattsson, Haakan; Thunehed, Hans (GeoVista AB, Luleaa (Sweden)); Juhlin, Christopher (Dept. of Earth Sciences, Uppsala Univ., Uppsala (Sweden))

    2008-11-15

    The geological work during the SDM Site Laxemar modelling stage has involved the continued development of deterministic models for rock domains (RSM) and deformation zones (ZSM), the identification and deterministic modelling of fracture domains (FSM), and the development of statistical models for fractures and minor deformation zones (geological discrete fracture network (DFN) modelling). The geological DFN model addresses fractures/structures with a size of less than 1 km, which is the lower cut-off of structures included in the deterministic modelling of deformation zones. In order to take account of variability in data resolution, deterministic models for rock domains and deformation zones are presented in both regional and local scale model volumes, while the geological DFN model is valid only within specific fracture domains inside the Laxemar local model volume. The geological and geophysical data that constitute the basis for the SDM-Site Laxemar modelling work comprise all data that have been acquired from Laxemar, i.e. all data that were available at the data freeze for SDM-Site Laxemar at August 31, 2007. Selected quality controlled data from the complementary cored borehole KLX27A have also been utilised in the modelling work. Data from the following investigations were acquired during the complete site investigation between the data freezes for Laxemar 1.2 and SDM-Site Laxemar as defined above: A revised bedrock geological map at the ground surface. Geological and geophysical data from 40 new cored boreholes and 14 percussion boreholes. Sampling and subsequent modal and geochemical analytical work of bedrock samples taken in connection with excavations in southern Laxemar. Detailed mapping of fractures and rock units along 10 trench excavations and 2 large surface exposures (drill sites for KLX09 and KLX11A/KLX20A). Special studies involving more detailed characterisation of deformation zones identified in the geological single-hole interpretation

  18. Surface system Forsmark. Site descriptive modelling SDM-Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Lindborg, Tobias [ed.

    2008-12-15

    SKB has undertaken site characterization of two different areas, Forsmark and Laxemar-Simpevarp, in order to find a suitable location for a geological repository for spent nuclear fuel. This report focuses on the site descriptive modelling of the surface system at Forsmark. The characterization of the surface system at the site was primarily made by identifying and describing important properties in different parts of the surface system, properties concerning e.g. hydrology and climate, Quaternary deposits and soils, hydrochemistry, vegetation, ecosystem functions, but also current and historical land use. The report presents available input data, methodology for data evaluation and modelling, and resulting models for each of the different disciplines. Results from the modelling of the surface system are also integrated with results from modelling of the deep bedrock system. The Forsmark site is located within the municipality of Oesthammar, about 120 km north of Stockholm. The investigated area is located along the shoreline of Oeregrundsgrepen, a funnel-shaped bay of the Baltic Sea. The area is characterized by small-scale topographic variations and is almost entirely located at altitudes lower than 20 metres above sea level. The Quaternary deposits in the area are dominated by till, characterized by a rich content of calcite which was transported by the glacier ice to the area from the sedimentary bedrock of Gaevlebukten about 100 km north of Forsmark. As a result, the surface waters and shallow groundwater at Forsmark are characterized by high pH values and high concentrations of certain major constituents, especially calcium and bicarbonate. The annual precipitation and runoff are 560 and 150 mm, respectively. The lakes are small and shallow, with mean and maximum depths ranging from approximately 0.1 to 1 m and 0.4 to 2 m. Sea water flows into the most low-lying lakes during events giving rise to very high sea levels. Wetlands are frequent and cover 25 to 35

  19. Geological discrete fracture network model for the Laxemar site. Site Descriptive Modelling. SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    La Pointe, Paul; Fox, Aaron (Golder Associates Inc (United States)); Hermanson, Jan; Oehman, Johan (Golder Associates AB, Stockholm (Sweden))

    2008-12-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is performing site characterization at two different locations, Forsmark and Laxemar, in order to locate a site for a final geologic repository for spent nuclear fuel. The program is built upon the development of Site Descriptive Models (SDMs) at specific timed data freezes. Each SDM is formed from discipline-specific reports from across the scientific spectrum. This report describes the methods, analyses, and conclusions of the modelling team in the production of the SDM-Site Laxemar geological discrete-fracture network (DFN) model. The DFN builds upon the work of other geological models, including the deformation zone and rock domain models. The geological DFN is a statistical model for stochastically simulating rock fractures and minor deformation zones at a scale of less than 1,000 m (the lower cut-off of the DZ models). The geological DFN is valid within six distinct fracture domains inside the Laxemar local model subarea: FSM{sub C}, FSM{sub E}W007, FSM{sub N}, FSM{sub N}E005, FSM{sub S}, and FSM{sub W}. The models are built using data from detailed surface outcrop maps, geophysical lineament maps, and the cored borehole record at Laxemar. The conceptual model for the SDM-Site Laxemar geological DFN model revolves around the identification of fracture domains based on relative fracture set intensities, orientation clustering, and the regional tectonic framework (including deformation zones). A single coupled fracture size/fracture intensity concept (the Base Model) based on a Pareto (power-law) distribution for fracture sizes was chosen as the recommended parameterisation. A slew of alternative size-intensity models were also carried through the fracture analyses and into the uncertainty and model verification analyses. Uncertainty is modelled by analysing the effects on fracture intensity (P32) that alternative model cases can have. Uncertainty is parameterised as a ratio between the P32 of the

  20. Geological discrete fracture network model for the Laxemar site. Site Descriptive Modelling. SDM-Site Laxemar

    International Nuclear Information System (INIS)

    La Pointe, Paul; Fox, Aaron; Hermanson, Jan; Oehman, Johan

    2008-10-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is performing site characterization at two different locations, Forsmark and Laxemar, in order to locate a site for a final geologic repository for spent nuclear fuel. The program is built upon the development of Site Descriptive Models (SDMs) at specific timed data freezes. Each SDM is formed from discipline-specific reports from across the scientific spectrum. This report describes the methods, analyses, and conclusions of the modelling team in the production of the SDM-Site Laxemar geological discrete-fracture network (DFN) model. The DFN builds upon the work of other geological models, including the deformation zone and rock domain models. The geological DFN is a statistical model for stochastically simulating rock fractures and minor deformation zones at a scale of less than 1,000 m (the lower cut-off of the DZ models). The geological DFN is valid within six distinct fracture domains inside the Laxemar local model subarea: FSM C , FSM E W007, FSM N , FSM N E005, FSM S , and FSM W . The models are built using data from detailed surface outcrop maps, geophysical lineament maps, and the cored borehole record at Laxemar. The conceptual model for the SDM-Site Laxemar geological DFN model revolves around the identification of fracture domains based on relative fracture set intensities, orientation clustering, and the regional tectonic framework (including deformation zones). A single coupled fracture size/fracture intensity concept (the Base Model) based on a Pareto (power-law) distribution for fracture sizes was chosen as the recommended parameterisation. A slew of alternative size-intensity models were also carried through the fracture analyses and into the uncertainty and model verification analyses. Uncertainty is modelled by analysing the effects on fracture intensity (P32) that alternative model cases can have. Uncertainty is parameterised as a ratio between the P32 of the alternative model and the P

  1. Hydrogeological Site Descriptive Model - a strategy for its development during Site Investigations

    Energy Technology Data Exchange (ETDEWEB)

    Rhen, Ingvar [SWECO VIAK AB, Goeteborg (Sweden); Follin, Sven [SF GeoLogic AB, Stockholm (Sweden); Hermanson, Jan [Golder Associates, Stockholm (Sweden)

    2003-04-01

    The report is to present a strategy for the development of the Site Descriptive Hydrogeological Model within the SKB Site Investigation Programme. The report, and similar reports from the Geology, Rock Mechanics, Thermal properties, Hydrogeochemistry, Transport Properties and Surface Ecosystem disciplines are intended to guide SKB Site Descriptive Modelling but also to provide the authorities with an overview of how the modelling should be performed. Thus the objectives of this report are to: provide guidelines for the modelling of different sites resulting in consistent handling of modelling issues during the Site Investigations, provide a structure for the modelling sequence that is suitable for the establishment of a Site Descriptive model and provide some necessary details that should be considered in a Site Descriptive model.

  2. Hydrogeological Site Descriptive Model - a strategy for its development during Site Investigations

    International Nuclear Information System (INIS)

    Rhen, Ingvar; Follin, Sven; Hermanson, Jan

    2003-04-01

    The report is to present a strategy for the development of the Site Descriptive Hydrogeological Model within the SKB Site Investigation Programme. The report, and similar reports from the Geology, Rock Mechanics, Thermal properties, Hydrogeochemistry, Transport Properties and Surface Ecosystem disciplines are intended to guide SKB Site Descriptive Modelling but also to provide the authorities with an overview of how the modelling should be performed. Thus the objectives of this report are to: provide guidelines for the modelling of different sites resulting in consistent handling of modelling issues during the Site Investigations, provide a structure for the modelling sequence that is suitable for the establishment of a Site Descriptive model and provide some necessary details that should be considered in a Site Descriptive model

  3. Olkiluoto site description 2011

    International Nuclear Information System (INIS)

    2012-12-01

    This fourth version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2008 with the data and knowledge obtained up to December 2010. A descriptive model of the site (the Site Descriptive Model, SDM), i.e. a model describing the geological and hydrogeological structure of the site, properties of the bedrock and the groundwater and its flow, and the associated interacting processes and mechanisms. The SDM is divided into six parts: surface system, geology, rock mechanics, hydrogeology, hydrogeochemistry and transport properties

  4. Olkiluoto site description 2011

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-12-15

    This fourth version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2008 with the data and knowledge obtained up to December 2010. A descriptive model of the site (the Site Descriptive Model, SDM), i.e. a model describing the geological and hydrogeological structure of the site, properties of the bedrock and the groundwater and its flow, and the associated interacting processes and mechanisms. The SDM is divided into six parts: surface system, geology, rock mechanics, hydrogeology, hydrogeochemistry and transport properties.

  5. Hydrogeochemical site descriptive model - a strategy for the model development during site investigations

    International Nuclear Information System (INIS)

    Smellie, John; Laaksoharju, Marcus; Tullborg, Eva-Lena

    2002-12-01

    In 2002, SKB commenced site characterisation investigations using deep boreholes at different sites. As an integral part of the planning work SKB has prepared a strategy to develop a Hydrogeochemical Site Descriptive Model; similar strategies have been developed for the other major geoscience disciplines. The main objectives of the Hydrogeochemical Site Descriptive Model are to describe the chemistry and distribution of the groundwater in the bedrock and overburden and the hydrogeochemical processes involved in its origin and evolution. This description is based primarily on measurements of the groundwater composition but incorporates the use of available geological and hydrogeological site descriptive models. The SKB hydrogeochemistry programme is planned to fulfil two basic requirements: 1) to provide representative and quality assured data for use as input parameter values in calculating long-term repository safety, and 2) to understand the present undisturbed hydrogeochemical conditions and how these conditions will change in the future. Parameter values for safety analysis include pH, Eh, S, SO 4 , HCO 3 , HPO 4 and TDS (mainly cations), together with colloids, fulvic and humic acids, other organics, bacteria and nitrogen. These values will be used to characterise the groundwater environment at, above and below repository depths. In the hydrogeochemical site investigation programme the number and location of the sampling points will be constrained by: a) geology (e.g. topography, overburden types, bedrock structures etc), b) hydrogeology (e.g. groundwater recharge/discharge areas, residence times), c) reliability (e.g. undisturbed vs disturbed groundwater chemical conditions), and d) resources (e.g. number and type of samples, and also available personnel, may be restricted by budgetary and schedule concerns). Naturally a balance is required between these constraints and the scientific aims of the programme. The constraints should never detrimentally affect

  6. Geological Site Descriptive Model. A strategy for the model development during site investigations

    International Nuclear Information System (INIS)

    Munier, Raymond; Stenberg, Leif; Stanfors, Roy; Milnes, Allan Geoffrey; Hermanson, Jan; Triumf, Carl-Axel

    2003-04-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is at present conducting site investigations as a preliminary to building an underground nuclear waste disposal facility in Sweden. This report presents a methodology for constructing, visualising and presenting 3-dimensional geological models, based on data from the site investigations. The methodology integrates with the overall work-flow of the site investigations, from the collection of raw data to the complete site description, as proposed in several earlier technical reports. Further, it is specifically designed for interaction with SICADA - SKB's Site Characterisation Database - and RVS - SKB's Rock Visualisation System. This report is one in a series of strategy documents intended to demonstrate how modelling is to be performed within each discipline. However, it also has a wider purpose, since the geological site descriptive model provides the basic geometrical framework for all the other disciplines. Hence, the wider aim is to present a practical and clear methodology for the analysis and interpretation of input data for use in the construction of the geology-based 3D geometrical model. In addition to the various aspects of modelling described above, the methodology presented here should therefore also provide: guidelines and directives on how systematic interpretation and integration of geo-scientific data from the different investigation methods should be carried out; guidelines on how different geometries should be created in the geological models; guidelines on how the assignment of parameters to the different geological units in RVS should be accomplished; guidelines on the handling of uncertainty at different points in the interpretation process. In addition, it should clarify the relation between the geological model and other models used in the processes of site characterisation, repository layout and safety analysis. In particular, integration and transparency should be promoted. The

  7. Geological Site Descriptive Model. A strategy for the model development during site investigations

    Energy Technology Data Exchange (ETDEWEB)

    Munier, Raymond; Stenberg, Leif [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Stanfors, Roy [Roy Stanfors Consulting, Lund (Sweden); Milnes, Allan Geoffrey [GEA Consulting, Uppsala (Sweden); Hermanson, Jan [Golder Associates, Stockholm (Sweden); Triumf, Carl-Axel [Geovista, Luleaa (Sweden)

    2003-04-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is at present conducting site investigations as a preliminary to building an underground nuclear waste disposal facility in Sweden. This report presents a methodology for constructing, visualising and presenting 3-dimensional geological models, based on data from the site investigations. The methodology integrates with the overall work-flow of the site investigations, from the collection of raw data to the complete site description, as proposed in several earlier technical reports. Further, it is specifically designed for interaction with SICADA - SKB's Site Characterisation Database - and RVS - SKB's Rock Visualisation System. This report is one in a series of strategy documents intended to demonstrate how modelling is to be performed within each discipline. However, it also has a wider purpose, since the geological site descriptive model provides the basic geometrical framework for all the other disciplines. Hence, the wider aim is to present a practical and clear methodology for the analysis and interpretation of input data for use in the construction of the geology-based 3D geometrical model. In addition to the various aspects of modelling described above, the methodology presented here should therefore also provide: guidelines and directives on how systematic interpretation and integration of geo-scientific data from the different investigation methods should be carried out; guidelines on how different geometries should be created in the geological models; guidelines on how the assignment of parameters to the different geological units in RVS should be accomplished; guidelines on the handling of uncertainty at different points in the interpretation process. In addition, it should clarify the relation between the geological model and other models used in the processes of site characterisation, repository layout and safety analysis. In particular, integration and transparency should be

  8. Description of regolith at Laxemar-Simpevarp. Site descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Sohlenius, Gustav; Hedenstroem, Anna

    2008-11-01

    This report compiles all known available information regarding the regolith in the Laxemar-Simpevarp regional model area. Regolith refers to the loose deposits overlying the bedrock. In the Laxemar-Simpevarp area, all known regolith was deposited during the Quaternary period and is consequently often referred to as Quaternary deposits (QD). In the terrestrial areas the uppermost part of the regolith, which has been affected by climate and vegetation, is referred to as soil. The geographical and stratigraphical distributions of the regolith have been used to construct a model showing the distribution of regolith depths in the whole model area. The stratigraphical units shown in the regolith depth and stratigraphy model have been characterised with respect to physical and chemical properties. Most of the data used for that characterisation have been obtained from the site investigation but some data were taken from the literature. All QD in the Laxemar area have most probably been deposited during or after the latest deglaciation. The ice sheet in the area moved from the north-west during the latest ice age. The Baltic Sea completely covered the investigated area after the latest deglaciation c 12,000 BC. Land uplift was fastest during the first few thousand years following the deglaciation and has subsequently decreased to the present value of 1 mm/year. Older QD have been eroded in areas exposed to waves and currents and the material has later been redeposited. Fine-grained sediments have been deposited on the floor of bays and in other sheltered positions. Peat has accumulated in many of the wetlands situated in topographically low positions. The groundwater table in many of the former wetlands has been artificially lowered to obtain land for forestry and agriculture, which has caused the peat to partly or completely oxidise. As land uplift proceeds, some new areas are being subjected to erosion at the same time as other new areas are becoming lakes and sheltered

  9. Description of regolith at Laxemar-Simpevarp. Site descriptive modelling SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Sohlenius, Gustav; Hedenstroem, Anna (Geological Survey of Sweden (SGU), Uppsala (Sweden))

    2008-11-15

    This report compiles all known available information regarding the regolith in the Laxemar-Simpevarp regional model area. Regolith refers to the loose deposits overlying the bedrock. In the Laxemar-Simpevarp area, all known regolith was deposited during the Quaternary period and is consequently often referred to as Quaternary deposits (QD). In the terrestrial areas the uppermost part of the regolith, which has been affected by climate and vegetation, is referred to as soil. The geographical and stratigraphical distributions of the regolith have been used to construct a model showing the distribution of regolith depths in the whole model area. The stratigraphical units shown in the regolith depth and stratigraphy model have been characterised with respect to physical and chemical properties. Most of the data used for that characterisation have been obtained from the site investigation but some data were taken from the literature. All QD in the Laxemar area have most probably been deposited during or after the latest deglaciation. The ice sheet in the area moved from the north-west during the latest ice age. The Baltic Sea completely covered the investigated area after the latest deglaciation c 12,000 BC. Land uplift was fastest during the first few thousand years following the deglaciation and has subsequently decreased to the present value of 1 mm/year. Older QD have been eroded in areas exposed to waves and currents and the material has later been redeposited. Fine-grained sediments have been deposited on the floor of bays and in other sheltered positions. Peat has accumulated in many of the wetlands situated in topographically low positions. The groundwater table in many of the former wetlands has been artificially lowered to obtain land for forestry and agriculture, which has caused the peat to partly or completely oxidise. As land uplift proceeds, some new areas are being subjected to erosion at the same time as other new areas are becoming lakes and sheltered

  10. Site descriptive modeling as a part of site characterization in Sweden - Concluding the surface based investigations

    International Nuclear Information System (INIS)

    Andersson, Johan; Winberg, Anders; Skagius, Kristina; Stroem, Anders; Lindborg, Tobias

    2007-01-01

    The Swedish Nuclear Fuel and Waste Management Co., SKB, is currently finalizing its surface based site investigations for the final repository for spent nuclear fuel in the municipalities of Oestharmnar (the Forsmark area) and Oskarshamn (the Simpevar/Laxemar area). The investigation data are assessed into a Site Descriptive Model, constituting a synthesis of geology, rock mechanics, thermal properties, hydrogeology, hydro-geochemistry, transport properties and a surface system description. Site data constitute a wide range of different measurement results. These data both need to be checked for consistency and to be interpreted into a format more amenable for three-dimensional modeling. The three-dimensional modeling (i.e. estimating the distribution of parameter values in space) is made in a sequence where the geometrical framework is taken from the geological models and in turn used by the rock mechanics, thermal and hydrogeological modeling. These disciplines in turn are partly interrelated, and also provide feedback to the geological modeling, especially if the geological description appears unreasonable when assessed together with the other data. Procedures for assessing the uncertainties and the confidence in the modeling have been developed during the course of the site modeling. These assessments also provide key input to the completion of the site investigation program. (authors)

  11. Thermal site descriptive model. A strategy for the model development during site investigations - version 2

    Energy Technology Data Exchange (ETDEWEB)

    Back, Paer-Erik; Sundberg, Jan [Geo Innova AB (Sweden)

    2007-09-15

    This report presents a strategy for describing, predicting and visualising the thermal aspects of the site descriptive model. The strategy is an updated version of an earlier strategy applied in all SDM versions during the initial site investigation phase at the Forsmark and Oskarshamn areas. The previous methodology for thermal modelling did not take the spatial correlation fully into account during simulation. The result was that the variability of thermal conductivity in the rock mass was not sufficiently well described. Experience from earlier thermal SDMs indicated that development of the methodology was required in order describe the spatial distribution of thermal conductivity in the rock mass in a sufficiently reliable way, taking both variability within rock types and between rock types into account. A good description of the thermal conductivity distribution is especially important for the lower tail. This tail is important for the design of a repository because it affects the canister spacing. The presented approach is developed to be used for final SDM regarding thermal properties, primarily thermal conductivity. Specific objectives for the strategy of thermal stochastic modelling are: Description: statistical description of the thermal conductivity of a rock domain. Prediction: prediction of thermal conductivity in a specific rock volume. Visualisation: visualisation of the spatial distribution of thermal conductivity. The thermal site descriptive model should include the temperature distribution and thermal properties of the rock mass. The temperature is the result of the thermal processes in the repository area. Determination of thermal transport properties can be made using different methods, such as laboratory investigations, field measurements, modelling from mineralogical composition and distribution, modelling from density logging and modelling from temperature logging. The different types of data represent different scales, which has to be

  12. Thermal site descriptive model. A strategy for the model development during site investigations - version 2

    International Nuclear Information System (INIS)

    Back, Paer-Erik; Sundberg, Jan

    2007-09-01

    This report presents a strategy for describing, predicting and visualising the thermal aspects of the site descriptive model. The strategy is an updated version of an earlier strategy applied in all SDM versions during the initial site investigation phase at the Forsmark and Oskarshamn areas. The previous methodology for thermal modelling did not take the spatial correlation fully into account during simulation. The result was that the variability of thermal conductivity in the rock mass was not sufficiently well described. Experience from earlier thermal SDMs indicated that development of the methodology was required in order describe the spatial distribution of thermal conductivity in the rock mass in a sufficiently reliable way, taking both variability within rock types and between rock types into account. A good description of the thermal conductivity distribution is especially important for the lower tail. This tail is important for the design of a repository because it affects the canister spacing. The presented approach is developed to be used for final SDM regarding thermal properties, primarily thermal conductivity. Specific objectives for the strategy of thermal stochastic modelling are: Description: statistical description of the thermal conductivity of a rock domain. Prediction: prediction of thermal conductivity in a specific rock volume. Visualisation: visualisation of the spatial distribution of thermal conductivity. The thermal site descriptive model should include the temperature distribution and thermal properties of the rock mass. The temperature is the result of the thermal processes in the repository area. Determination of thermal transport properties can be made using different methods, such as laboratory investigations, field measurements, modelling from mineralogical composition and distribution, modelling from density logging and modelling from temperature logging. The different types of data represent different scales, which has to be

  13. Hydrogeochemical site descriptive model - a strategy for the model development during site investigations

    Energy Technology Data Exchange (ETDEWEB)

    Smellie, John [Conterra AB, Uppsala (Sweden); Laaksoharju, Marcus [GeoPoint AB, Sollentuna (Sweden); Tullborg, Eva-Lena [Terralogica AB, Graabo (Sweden)

    2002-12-01

    In 2002, SKB commenced site characterisation investigations using deep boreholes at different sites. As an integral part of the planning work SKB has prepared a strategy to develop a Hydrogeochemical Site Descriptive Model; similar strategies have been developed for the other major geoscience disciplines. The main objectives of the Hydrogeochemical Site Descriptive Model are to describe the chemistry and distribution of the groundwater in the bedrock and overburden and the hydrogeochemical processes involved in its origin and evolution. This description is based primarily on measurements of the groundwater composition but incorporates the use of available geological and hydrogeological site descriptive models. The SKB hydrogeochemistry programme is planned to fulfil two basic requirements: 1) to provide representative and quality assured data for use as input parameter values in calculating long-term repository safety, and 2) to understand the present undisturbed hydrogeochemical conditions and how these conditions will change in the future. Parameter values for safety analysis include pH, Eh, S, SO{sub 4}, HCO{sub 3}, HPO{sub 4} and TDS (mainly cations), together with colloids, fulvic and humic acids, other organics, bacteria and nitrogen. These values will be used to characterise the groundwater environment at, above and below repository depths. In the hydrogeochemical site investigation programme the number and location of the sampling points will be constrained by: a) geology (e.g. topography, overburden types, bedrock structures etc), b) hydrogeology (e.g. groundwater recharge/discharge areas, residence times), c) reliability (e.g. undisturbed vs disturbed groundwater chemical conditions), and d) resources (e.g. number and type of samples, and also available personnel, may be restricted by budgetary and schedule concerns). Naturally a balance is required between these constraints and the scientific aims of the programme. The constraints should never

  14. Thermal Site Descriptive Model. A strategy for the model development during site investigations. Version 1.0

    International Nuclear Information System (INIS)

    Sundberg, Jan

    2003-04-01

    Site investigations are in progress for the siting of a deep repository for spent nuclear fuel. As part of the planning work, strategies are developed for site descriptive modelling regarding different disciplines, amongst them the thermal conditions. The objective of the strategy for a thermal site descriptive model is to guide the practical implementation of evaluating site specific data during the site investigations. It is understood that further development may be needed. The model describes the thermal properties and other thermal parameters of intact rock, fractures and fracture zones, and of the rock mass. The methodology is based on estimation of thermal properties of intact rock and discontinuities, using both empirical and theoretical/numerical approaches, and estimation of thermal processes using mathematical modelling. The methodology will be used and evaluated for the thermal site descriptive modelling at the Aespoe Hard Rock Laboratory

  15. Validation of coastal oceanographic models at Forsmark. Site descriptive modelling SDM-Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Engqvist, Anders (A och I Engqvist Konsult HB, Vaxholm (SE)); Andrejev, Oleg (Finnish Inst. of Marine Research, Helsinki (FI))

    2008-01-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterisation at two different locations, the Forsmark and the Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. The characterisation work is divided into an initial site investigation phase and a complete site investigation phase. In this context, the water exchange of the coastal zone is one link of the chain of possible nuclide transport mechanisms that must be assessed in the site description of potential repository areas. For the purpose of validating the pair of nested 3D-models employed to simulate the water exchange in the near-shore coastal zone in the Forsmark area, an encompassing measurement program entailing six stations has been performed. The design of this program was to first assess to what degree the forcing of the fine resolution (FR) model of the Forsmark study area at its interfacial boundary to the coarse resolution (CR) model of the entire Baltic was reproduced. In addition to this scrutiny it is of particular interest how the time-varying density-determining properties, salinity and temperature, at the borders are propagated into the FR-domain, since this corresponds to the most efficient mode of water exchange. An important part of the validation process has been to carefully evaluate which measurement data that can be considered reliable. The result was that several periods of foremost near-surface salinity data had to be discarded due to growth of algae on the conductivity sensors. Lack of thorough absolute calibration of the salinity meters also necessitates dismissal of measurement data. Relative the assessed data that can be accepted as adequate, the outcome of the validation can be summarized in five points: (i) The surface-most salinity of the CR-model drifts downward a little less than one practical salinity unit (psu) per year, requiring that the ensuing correlation analysis be subdivided into periods of a

  16. Validation of coastal oceanographic models at Forsmark. Site descriptive modelling SDM-Site Forsmark

    International Nuclear Information System (INIS)

    Engqvist, Anders; Andrejev, Oleg

    2008-01-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterisation at two different locations, the Forsmark and the Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. The characterisation work is divided into an initial site investigation phase and a complete site investigation phase. In this context, the water exchange of the coastal zone is one link of the chain of possible nuclide transport mechanisms that must be assessed in the site description of potential repository areas. For the purpose of validating the pair of nested 3D-models employed to simulate the water exchange in the near-shore coastal zone in the Forsmark area, an encompassing measurement program entailing six stations has been performed. The design of this program was to first assess to what degree the forcing of the fine resolution (FR) model of the Forsmark study area at its interfacial boundary to the coarse resolution (CR) model of the entire Baltic was reproduced. In addition to this scrutiny it is of particular interest how the time-varying density-determining properties, salinity and temperature, at the borders are propagated into the FR-domain, since this corresponds to the most efficient mode of water exchange. An important part of the validation process has been to carefully evaluate which measurement data that can be considered reliable. The result was that several periods of foremost near-surface salinity data had to be discarded due to growth of algae on the conductivity sensors. Lack of thorough absolute calibration of the salinity meters also necessitates dismissal of measurement data. Relative the assessed data that can be accepted as adequate, the outcome of the validation can be summarized in five points: (i) The surface-most salinity of the CR-model drifts downward a little less than one practical salinity unit (psu) per year, requiring that the ensuing correlation analysis be subdivided into periods of a

  17. A descriptive ecosystem model - a strategy for model development during site investigations

    International Nuclear Information System (INIS)

    Loefgren, Anders

    2003-09-01

    This report describes a strategy for the development of a site descriptive model for the surface ecosystem on the potential deep repository sites. The surface ecosystem embraces many disciplines, and these have to be identified, described and integrated in order to construct a descriptive ecosystem model that describes and quantifies biotic and abiotic patterns and processes of importance for the ecosystem on the site. The descriptive model includes both present day conditions and historical information. The descriptive ecosystem model will be used to supply input data for the safety assessment and to serve as the baseline model for devising a monitoring program to detect short-term disturbances caused first by the site investigations and later by the construction of the deep repository. Furthermore, it will serve as a reference for future comparisons to determine more long-term effects or changes caused by the deep repository. The report adopts a non-site-specific approach focusing on the following aims: 1. To present and define the properties that will constitute the descriptive ecosystem model. 2. To present a methodology for determining those properties. 3. To describe and develop the framework for the descriptive ecosystem model by integrating the different properties. 4. To present vital data from other site descriptive models such as those for geology or hydrogeology that interacts with and affects the descriptive ecosystem model. The properties are described under four different sections: general physical properties of the landscape, the terrestrial system, the limnic system and the marine system. These headings are further subdivided into entities that integrate properties in relation to processes

  18. A descriptive ecosystem model - a strategy for model development during site investigations

    Energy Technology Data Exchange (ETDEWEB)

    Loefgren, Anders [Stockholm Univ. (Sweden). Dept. of Botany; Lindborg, Tobias [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

    2003-09-01

    This report describes a strategy for the development of a site descriptive model for the surface ecosystem on the potential deep repository sites. The surface ecosystem embraces many disciplines, and these have to be identified, described and integrated in order to construct a descriptive ecosystem model that describes and quantifies biotic and abiotic patterns and processes of importance for the ecosystem on the site. The descriptive model includes both present day conditions and historical information. The descriptive ecosystem model will be used to supply input data for the safety assessment and to serve as the baseline model for devising a monitoring program to detect short-term disturbances caused first by the site investigations and later by the construction of the deep repository. Furthermore, it will serve as a reference for future comparisons to determine more long-term effects or changes caused by the deep repository. The report adopts a non-site-specific approach focusing on the following aims: 1. To present and define the properties that will constitute the descriptive ecosystem model. 2. To present a methodology for determining those properties. 3. To describe and develop the framework for the descriptive ecosystem model by integrating the different properties. 4. To present vital data from other site descriptive models such as those for geology or hydrogeology that interacts with and affects the descriptive ecosystem model. The properties are described under four different sections: general physical properties of the landscape, the terrestrial system, the limnic system and the marine system. These headings are further subdivided into entities that integrate properties in relation to processes.

  19. Technical know-how of site descriptive modeling for site characterization - 59089

    International Nuclear Information System (INIS)

    Saegusa, Hiromitsu; Onoe, Hironori; Doke, Ryosuke; Niizato, Tadafumi; Yasue, Ken-ichi

    2012-01-01

    The site descriptive model covering the current status of characteristics of geological environment and the site evolution model for estimation of the long-term evolution of site conditions are used to integrate multi-disciplinary investigation results. It is important to evaluate uncertainties in the models, to specify issues regarding the uncertainties and to prioritize the resolution of specified issues, for the planning of site characterization. There is a large quantity of technical know-how in the modeling process. It is important to record the technical know-how with transparency and traceability, since site characterization projects generally need long duration. The transfer of the technical know-how accumulated in the research and development (R and D) phase to the implementation phase is equally important. The aim of this study is to support the planning of initial surface-based site characterizations based on the technical know-how accumulated from the underground research laboratory projects. These projects are broad scientific studies of the deep geological environment and provide a technical basis for the geological disposal of high-level radioactive wastes. In this study, a comprehensive task flow from acquisition of existing data to planning of field investigations through the modeling has been specified. Specific task flow and decision-making process to perform the tasks have been specified. (authors)

  20. Validation of coastal oceanographic models at Laxemar-Simpevarp. Site descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Engqvist, Anders; Andrejev, Oleg

    2008-12-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterization at two different locations, the Forsmark and the Laxemar-Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. The characterization work is divided into an initial site investigation phase and a complete site investigation phase. In this context, the water exchange of the coastal zone is one link of the chain of possible nuclide transport mechanisms that must be assessed in the site description of potential repository areas. For the purpose of validating the pair of nested 3D-models and the coupled discrete basin (CDB-) model employed to simulate the water exchange in the near-shore coastal zone in the Laxemar-Simpevarp area, an encompassing measurement program entailing data from six stations (of which two are close) has been performed. The design of this program was to first assess to what degree the forcing of the fine resolution (FR-) model of the Laxemar- Simpevarp study area at its interfacial boundary to the coarse resolution (CR-) model of the entire Baltic was reproduced. In addition to this, it is of particular interest how the time-varying density-determining properties, salinity and temperature, at the borders are propagated into the FR-domain and further influence the water exchange with the interior, more secluded, basins. An important part of the validation process has been to carefully evaluate which measurement data that can be considered reliable. The result was that some periods of foremost near-surface salinity data had to be discarded due to growth of algae on the conductivity sensors. Interference with ship traffic and lack of absolute calibration of the salinity meters necessitated dismissal of measurement data too. In this study so-called Mesan data have been consistently used for the meteorological forcing of the 3D-models. Relative the assessed data that can be accepted as adequate, the outcome of the

  1. Validation of coastal oceanographic models at Laxemar-Simpevarp. Site descriptive modelling SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Engqvist, Anders (A och I Engqvist Konsult HB, Vaxholm (SE)); Andrejev, Oleg (Finnish Inst. of Marine Research, Helsinki (FI))

    2008-12-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterization at two different locations, the Forsmark and the Laxemar-Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. The characterization work is divided into an initial site investigation phase and a complete site investigation phase. In this context, the water exchange of the coastal zone is one link of the chain of possible nuclide transport mechanisms that must be assessed in the site description of potential repository areas. For the purpose of validating the pair of nested 3D-models and the coupled discrete basin (CDB-) model employed to simulate the water exchange in the near-shore coastal zone in the Laxemar-Simpevarp area, an encompassing measurement program entailing data from six stations (of which two are close) has been performed. The design of this program was to first assess to what degree the forcing of the fine resolution (FR-) model of the Laxemar- Simpevarp study area at its interfacial boundary to the coarse resolution (CR-) model of the entire Baltic was reproduced. In addition to this, it is of particular interest how the time-varying density-determining properties, salinity and temperature, at the borders are propagated into the FR-domain and further influence the water exchange with the interior, more secluded, basins. An important part of the validation process has been to carefully evaluate which measurement data that can be considered reliable. The result was that some periods of foremost near-surface salinity data had to be discarded due to growth of algae on the conductivity sensors. Interference with ship traffic and lack of absolute calibration of the salinity meters necessitated dismissal of measurement data too. In this study so-called Mesan data have been consistently used for the meteorological forcing of the 3D-models. Relative the assessed data that can be accepted as adequate, the outcome of the

  2. Description of surface hydrology and near-surface hydrogeology at Forsmark. Site descriptive modelling SDM. Site Forsmark

    International Nuclear Information System (INIS)

    Johansson, Per-Olof

    2008-12-01

    This report describes the modelling of the surface hydrology and near-surface hydrogeology that was performed for the final site descriptive model of Forsmark produced in the site investigation stage, SDM-Site Forsmark. The comprehensive investigation and monitoring programme forms a strong basis for the developed conceptual and descriptive model of the hydrological and near-surface hydrological system of the site investigation area. However, there are some remaining uncertainties regarding the interaction of deep and near-surface groundwater and surface water of importance for the understanding of the system: The groundwaters in till below Lake Eckarfjaerden, Lake Gaellbotraesket, Lake Fiskarfjaerden and Lake Bolundsfjaerden have high salinities. The hydrological and hydrochemical interpretations indicate that these waters are relict waters of mainly marine origin. From the perspective of the overall water balance, the water below the central parts of the lakes can be considered as stagnant. However, according to the hydrochemical interpretation, these waters also contain weak signatures of deep saline water. Rough chloride budget calculations for the Gaellbotraesket depression also raise the question of a possible upward flow of deep groundwater. No absolute conclusion can be drawn from the existing data analyses regarding the key question of whether there is a small ongoing upward flow of deep saline water. However, Lake Bolundsfjaerden is an exception where the clear downward flow gradient from the till to the bedrock excludes the possibility of an active deep saline source. The available data indicate that there are no discharge areas for flow systems involving deep bedrock groundwater in the northern part of the tectonic lens, where the repository is planned to be located (the so-called 'target area'). However, it can not be excluded that such discharge areas exist. Data indicate that the prevailing downward vertical flow gradients from the QD to the bedrock

  3. Description of surface hydrology and near-surface hydrogeology at Forsmark. Site descriptive modelling SDM. Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Johansson, Per-Olof (Artesia Grundvattenkonsult AB, Taeby (Sweden))

    2008-12-15

    This report describes the modelling of the surface hydrology and near-surface hydrogeology that was performed for the final site descriptive model of Forsmark produced in the site investigation stage, SDM-Site Forsmark. The comprehensive investigation and monitoring programme forms a strong basis for the developed conceptual and descriptive model of the hydrological and near-surface hydrological system of the site investigation area. However, there are some remaining uncertainties regarding the interaction of deep and near-surface groundwater and surface water of importance for the understanding of the system: The groundwaters in till below Lake Eckarfjaerden, Lake Gaellbotraesket, Lake Fiskarfjaerden and Lake Bolundsfjaerden have high salinities. The hydrological and hydrochemical interpretations indicate that these waters are relict waters of mainly marine origin. From the perspective of the overall water balance, the water below the central parts of the lakes can be considered as stagnant. However, according to the hydrochemical interpretation, these waters also contain weak signatures of deep saline water. Rough chloride budget calculations for the Gaellbotraesket depression also raise the question of a possible upward flow of deep groundwater. No absolute conclusion can be drawn from the existing data analyses regarding the key question of whether there is a small ongoing upward flow of deep saline water. However, Lake Bolundsfjaerden is an exception where the clear downward flow gradient from the till to the bedrock excludes the possibility of an active deep saline source. The available data indicate that there are no discharge areas for flow systems involving deep bedrock groundwater in the northern part of the tectonic lens, where the repository is planned to be located (the so-called 'target area'). However, it can not be excluded that such discharge areas exist. Data indicate that the prevailing downward vertical flow gradients from the QD to

  4. Olkiluoto site description 2006

    International Nuclear Information System (INIS)

    Andersson, J.; Ahokas, H.; Hudson, J.A.

    2007-03-01

    This second version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2004 (Posiva 2005) with the data and knowledge obtained up to December 2005. The main product of the modelling has been to develop a descriptive model of the site (the Site Descriptive Model), i.e. a model describing the geometry, properties of the bedrock and the water and the associated interacting processes and mechanisms. For practical reasons, the Site Descriptive Model is divided into five parts: surface system, geology, rock mechanics, hydrogeology and hydrogeochemistry, which are presented in individual chapters. Four separated models are presented: the geological, rock mechanics, hydrogeological and hydrogeochemical models. The consistency between the hydrogeological and hydrogeochemical models is assessed in a joint chapter. Chapter 1 presents an outline of the report, explains the background to its development and sets out its objectives and scope. It is also introduces and explains the integrated modelling methodology, the nomenclature used in the descriptions of the models and the prediction/outcome studies. Chapter 2 provides a brief overview of the data used for producing the Site Description. Chapters 3 to 8 present the descriptive modelling, which involves interpreting data, interpolating or extrapolating between measurement points and calibrating the model against data, based on the various assumptions made about each conceptual model. Chapter 9 presents the results of the prediction/outcome studies performed during 2005 and Chapter 10 the overall consistency and confidence assessment. Overall conclusions are provided in Chapter 11. The main advances since Site Report 2004 are: A new geological model is presented in Chapter 4, representing a significant change from Bedrock Model 2003/1. There has been extensive use of geological data, whereas hydrogeological data have deliberately not been used and more

  5. Geology Forsmark. Site descriptive modelling Forsmark - stage 2.2

    Energy Technology Data Exchange (ETDEWEB)

    Stephens, Michael B. [Geological Survey of Sweden, Uppsala (Sweden); Fox, Aaron; La Pointe, Paul [Golder Associates Inc (United States); Simeonov, Assen [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Isaksson, Hans [GeoVista AB, Luleaa (Sweden); Hermanson, Jan; Oehman, Johan [Golder Associates AB, Stockholm (Sweden)

    2007-10-15

    The geological work during stage 2.2 has involved the development of deterministic models for rock domains (RFM) and deformation zones (ZFM), the identification and deterministic modelling of fracture domains (FFM) inside the candidate volume, i.e. the parts of rock domains that are not affected by deformation zones, and the development of statistical models for fractures and minor deformation zones (geological discrete fracture network modelling or geological DFN modelling). The geological DFN model addresses brittle structures at a scale of less than 1 km, which is the lower cut-off in the deterministic modelling of deformation zones. In order to take account of variability in data resolution, deterministic models for rock domains and deformation zones are presented in both regional and local model volumes, while the geological DFN model is valid within specific fracture domains inside the north-western part of the candidate volume, including the target volume. The geological modelling work has evaluated and made use of: A revised bedrock geological map at the ground surface. Geological and geophysical data from 21 cored boreholes and 33 percussion boreholes. Detailed mapping of fractures and rock units along nine excavations or large surface outcrops. Data bearing on the characterisation (including kinematics) of deformation zones. Complementary geochronological and other rock and fracture analytical data. Lineaments identified on the basis of airborne and high-resolution ground magnetic data. A reprocessing of both surface and borehole reflection seismic data. Seismic refraction data. The outputs of the deterministic modelling work are geometric models in RVS format and detailed property tables for rock domains and deformation zones, and a description of fracture domains. The outputs of the geological DFN modelling process are recommended parameters or statistical distributions that describe fracture set orientations, radius sizes, volumetric intensities

  6. Geology Forsmark. Site descriptive modelling Forsmark - stage 2.2

    International Nuclear Information System (INIS)

    Stephens, Michael B.; Fox, Aaron; La Pointe, Paul; Simeonov, Assen; Isaksson, Hans; Hermanson, Jan; Oehman, Johan

    2007-10-01

    The geological work during stage 2.2 has involved the development of deterministic models for rock domains (RFM) and deformation zones (ZFM), the identification and deterministic modelling of fracture domains (FFM) inside the candidate volume, i.e. the parts of rock domains that are not affected by deformation zones, and the development of statistical models for fractures and minor deformation zones (geological discrete fracture network modelling or geological DFN modelling). The geological DFN model addresses brittle structures at a scale of less than 1 km, which is the lower cut-off in the deterministic modelling of deformation zones. In order to take account of variability in data resolution, deterministic models for rock domains and deformation zones are presented in both regional and local model volumes, while the geological DFN model is valid within specific fracture domains inside the north-western part of the candidate volume, including the target volume. The geological modelling work has evaluated and made use of: A revised bedrock geological map at the ground surface. Geological and geophysical data from 21 cored boreholes and 33 percussion boreholes. Detailed mapping of fractures and rock units along nine excavations or large surface outcrops. Data bearing on the characterisation (including kinematics) of deformation zones. Complementary geochronological and other rock and fracture analytical data. Lineaments identified on the basis of airborne and high-resolution ground magnetic data. A reprocessing of both surface and borehole reflection seismic data. Seismic refraction data. The outputs of the deterministic modelling work are geometric models in RVS format and detailed property tables for rock domains and deformation zones, and a description of fracture domains. The outputs of the geological DFN modelling process are recommended parameters or statistical distributions that describe fracture set orientations, radius sizes, volumetric intensities

  7. Rock mechanics site descriptive model-theoretical approach. Preliminary site description Forsmark area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Fredriksson, Anders; Olofsson, Isabelle [Golder Associates AB, Uppsala (Sweden)

    2005-12-15

    The present report summarises the theoretical approach to estimate the mechanical properties of the rock mass in relation to the Preliminary Site Descriptive Modelling, version 1.2 Forsmark. The theoretical approach is based on a discrete fracture network (DFN) description of the fracture system in the rock mass and on the results of mechanical testing of intact rock and on rock fractures. To estimate the mechanical properties of the rock mass a load test on a rock block with fractures is simulated with the numerical code 3DEC. The location and size of the fractures are given by DFN-realisations. The rock block was loaded in plain strain condition. From the calculated relationship between stresses and deformations the mechanical properties of the rock mass were determined. The influence of the geometrical properties of the fracture system on the mechanical properties of the rock mass was analysed by loading 20 blocks based on different DFN-realisations. The material properties of the intact rock and the fractures were kept constant. The properties are set equal to the mean value of each measured material property. The influence of the variation of the properties of the intact rock and variation of the mechanical properties of the fractures are estimated by analysing numerical load tests on one specific block (one DFN-realisation) with combinations of properties for intact rock and fractures. Each parameter varies from its lowest values to its highest values while the rest of the parameters are held constant, equal to the mean value. The resulting distribution was expressed as a variation around the value determined with mean values on all parameters. To estimate the resulting distribution of the mechanical properties of the rock mass a Monte-Carlo simulation was performed by generating values from the two distributions independent of each other. The two values were added and the statistical properties of the resulting distribution were determined.

  8. Rock mechanics site descriptive model-theoretical approach. Preliminary site description Forsmark area - version 1.2

    International Nuclear Information System (INIS)

    Fredriksson, Anders; Olofsson, Isabelle

    2005-12-01

    The present report summarises the theoretical approach to estimate the mechanical properties of the rock mass in relation to the Preliminary Site Descriptive Modelling, version 1.2 Forsmark. The theoretical approach is based on a discrete fracture network (DFN) description of the fracture system in the rock mass and on the results of mechanical testing of intact rock and on rock fractures. To estimate the mechanical properties of the rock mass a load test on a rock block with fractures is simulated with the numerical code 3DEC. The location and size of the fractures are given by DFN-realisations. The rock block was loaded in plain strain condition. From the calculated relationship between stresses and deformations the mechanical properties of the rock mass were determined. The influence of the geometrical properties of the fracture system on the mechanical properties of the rock mass was analysed by loading 20 blocks based on different DFN-realisations. The material properties of the intact rock and the fractures were kept constant. The properties are set equal to the mean value of each measured material property. The influence of the variation of the properties of the intact rock and variation of the mechanical properties of the fractures are estimated by analysing numerical load tests on one specific block (one DFN-realisation) with combinations of properties for intact rock and fractures. Each parameter varies from its lowest values to its highest values while the rest of the parameters are held constant, equal to the mean value. The resulting distribution was expressed as a variation around the value determined with mean values on all parameters. To estimate the resulting distribution of the mechanical properties of the rock mass a Monte-Carlo simulation was performed by generating values from the two distributions independent of each other. The two values were added and the statistical properties of the resulting distribution were determined

  9. Geological evolution, palaeoclimate and historical development of the Forsmark and Laxemar-Simpevarp areas. Site descriptive modelling SDM-Site

    Energy Technology Data Exchange (ETDEWEB)

    Soederbaeck, Bjoern [ed.

    2008-06-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterization at two different locations, the Forsmark and Laxemar-Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. The site investigations started in 2002 and were completed in 2007. The analysis and modelling of data from the site investigations, which have taken place during and after these investigations, provide a foundation for the development of an integrated, multidisciplinary site descriptive model (SDM) for each of the two sites. A site descriptive model constitutes a description of the site and its regional setting, covering the current state of the geosphere and the biosphere, as well as those natural processes that affect or have affected their long-term development. Hitherto, a number of reports presenting preliminary site descriptive models for Forsmark and Laxemar-Simpevarp have been published. In these reports, the evolutionary and historical aspects of the site were included in a separate chapter. The present report comprises a further elaboration of the evolutionary and historical information included in the preliminary SDM reports, but presented here in a separate, supplementary report to the final site description, SDM-Site. The report is common to the two investigated areas, and the overall objective is to describe the long-term geological evolution, the palaeoclimate, and the post-glacial development of ecosystems and of the human population at the two sites. The report largely consists of a synthesis of information derived from the scientific literature and other sources not related to the site investigations. However, considerable information from the site investigations that has contributed to our understanding of the past development at each site is also included. This unique synthesis of both published information in a regional perspective and new site-specific information breaks new ground in our understanding

  10. Geological evolution, palaeoclimate and historical development of the Forsmark and Laxemar-Simpevarp areas. Site descriptive modelling SDM-Site

    International Nuclear Information System (INIS)

    Soederbaeck, Bjoern

    2008-06-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterization at two different locations, the Forsmark and Laxemar-Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. The site investigations started in 2002 and were completed in 2007. The analysis and modelling of data from the site investigations, which have taken place during and after these investigations, provide a foundation for the development of an integrated, multidisciplinary site descriptive model (SDM) for each of the two sites. A site descriptive model constitutes a description of the site and its regional setting, covering the current state of the geosphere and the biosphere, as well as those natural processes that affect or have affected their long-term development. Hitherto, a number of reports presenting preliminary site descriptive models for Forsmark and Laxemar-Simpevarp have been published. In these reports, the evolutionary and historical aspects of the site were included in a separate chapter. The present report comprises a further elaboration of the evolutionary and historical information included in the preliminary SDM reports, but presented here in a separate, supplementary report to the final site description, SDM-Site. The report is common to the two investigated areas, and the overall objective is to describe the long-term geological evolution, the palaeoclimate, and the post-glacial development of ecosystems and of the human population at the two sites. The report largely consists of a synthesis of information derived from the scientific literature and other sources not related to the site investigations. However, considerable information from the site investigations that has contributed to our understanding of the past development at each site is also included. This unique synthesis of both published information in a regional perspective and new site-specific information breaks new ground in our understanding

  11. Thermal properties. Site descriptive modelling Forsmark - stage 2.2

    International Nuclear Information System (INIS)

    Back, Paer-Erik; Wrafter, John; Sundberg, Jan; Rosen, L ars

    2007-09-01

    The lithological data acquired from boreholes and mapping of the rock surface need to be reclassified into thermal rock classes, TRCs. The main reason is to simplify the simulations. The lithological data are used to construct models of the transition between different TRCs, thus describing the spatial statistical structure of each TRC. The result is a set of transition probability models that are used in the simulation of TRCs. The intermediate result of this first stochastic simulation is a number of realisations of the geology, each one equally probable. Based on the thermal data, a spatial statistical thermal model is constructed for each TRC. It consists of a statistical distribution and a variogram for each TRC. These are used in the stochastic simulation of thermal conductivity and the result is a number of equally probable realisations of thermal conductivity for the domain. In the next step, the realisations of TRCs (lithology) and thermal conductivity are merged, i.e. each realisation of geology is filled with simulated thermal conductivity values. The result is a set of realisations of thermal conductivity that considers both the difference in thermal properties between different TRCs, and the variability within each TRC. If the result is desired in a scale different from the simulation scale, i.e. the canister scale, upscaling of the realisations can be performed. The result is a set of equally probable realisations of thermal properties. The presented methodology was applied to rock domain RFM029 and RFM045. The main results are sets of realisations of thermal properties that can be used for further processing, most importantly for statistical analysis and numerical temperature simulations for the design of repository layout (distances between deposition holes). The main conclusions of the thermal modelling are: The choice of scale has a profound influence on the distribution of thermal conductivity values. The variance decreases and the lower tail

  12. Thermal properties. Site descriptive modelling Forsmark - stage 2.2

    Energy Technology Data Exchange (ETDEWEB)

    Back, Paer-Erik; Wrafter, John; Sundberg, Jan [Geo Innova AB (Sweden); Rosen, L ars [Sweco Viak AB (Sweden)

    2007-09-15

    The lithological data acquired from boreholes and mapping of the rock surface need to be reclassified into thermal rock classes, TRCs. The main reason is to simplify the simulations. The lithological data are used to construct models of the transition between different TRCs, thus describing the spatial statistical structure of each TRC. The result is a set of transition probability models that are used in the simulation of TRCs. The intermediate result of this first stochastic simulation is a number of realisations of the geology, each one equally probable. Based on the thermal data, a spatial statistical thermal model is constructed for each TRC. It consists of a statistical distribution and a variogram for each TRC. These are used in the stochastic simulation of thermal conductivity and the result is a number of equally probable realisations of thermal conductivity for the domain. In the next step, the realisations of TRCs (lithology) and thermal conductivity are merged, i.e. each realisation of geology is filled with simulated thermal conductivity values. The result is a set of realisations of thermal conductivity that considers both the difference in thermal properties between different TRCs, and the variability within each TRC. If the result is desired in a scale different from the simulation scale, i.e. the canister scale, upscaling of the realisations can be performed. The result is a set of equally probable realisations of thermal properties. The presented methodology was applied to rock domain RFM029 and RFM045. The main results are sets of realisations of thermal properties that can be used for further processing, most importantly for statistical analysis and numerical temperature simulations for the design of repository layout (distances between deposition holes). The main conclusions of the thermal modelling are: The choice of scale has a profound influence on the distribution of thermal conductivity values. The variance decreases and the lower tail

  13. Site descriptive modelling during characterization for a geological repository for nuclear waste in Sweden

    International Nuclear Information System (INIS)

    Stroem, A.; Andersson, J.; Skagius, K.; Winberg, A.

    2008-01-01

    The Swedish programme for geological disposal of spent nuclear fuel is approaching major milestones in the form of permit applications for an encapsulation plant and a deep geologic repository. This paper presents an overview of the bedrock and surface modelling work that comprises a major part of the on-going site characterization in Sweden and that results in syntheses of the sites, called site descriptions. The site description incorporates descriptive models of the site and its regional setting, including the current state of the geosphere and the biosphere as well as natural processes affecting long-term evolution. The site description is intended to serve the needs of both repository engineering with respect to layout and construction, and safety assessment, with respect to long-term performance. The development of site-descriptive models involves a multi-disciplinary interpretation of geology, rock mechanics, thermal properties, hydrogeology, hydrogeochemistry, transport properties and ecosystems using input in the form of available data for the surface and from deep boreholes

  14. Depth and stratigraphy of regolith. Site descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Nyman, Helena; Sohlenius, Gustav; Stroemgren, Maarten; Brydsten, Lars

    2008-06-01

    At the Laxemar-Simpevarp site, numerical and descriptive modelling are performed both for the deep bedrock and for the surface systems. The surface geology and regolith depth are important parameters for e.g. hydrogeological and geochemical modelling and for the over all understanding of the area. Regolith refers to all the unconsolidated deposits overlying the bedrock. The regolith depth model (RDM) presented here visualizes the stratigraphical distribution of the regolith as well as the elevation of the bedrock surface. The model covers 280 km 2 including both terrestrial and marine areas. In the model the stratigraphy is represented by six layers (Z1-Z6) that corresponds to different types of regolith. The model is geometric and the properties of the layers are assigned by the user according to the purpose. The GeoModel program, which is an ArcGIS extension, was used for modelling the regolith depths. A detailed topographical Digital Elevation Model (DEM) and a map of Quaternary deposits were used as input to the model. Altogether 319 boreholes and 440 other stratigraphical observations were also used. Furthermore a large number of depth data interpreted from geophysical investigations were used; refraction seismic measurements from 51 profiles, 11,000 observation points from resistivity measurements and almost 140,000 points from seismic and sediment echo sounding data. The results from the refraction seismic and resistivity measurements give information about the total regolith depths, whereas most other data also give information about the stratigraphy of the regolith. Some of the used observations did not reach the bedrock surface. They do, however, describe the minimum regolith depth at each location and were therefore used where the regolith depth would have been thinner without using the observation point. A large proportion of the modelled area has a low data density and the area was therefore divided into nine domains. These domains were defined based

  15. Depth and stratigraphy of regolith. Site descriptive modelling SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Nyman, Helena (SWECO Position, Stockholm (Sweden)); Sohlenius, Gustav (Geological Survey of Sweden (SGU), Uppsala (Sweden)); Stroemgren, Maarten; Brydsten, Lars (Umeaa Univ., Umeaa (Sweden))

    2008-06-15

    At the Laxemar-Simpevarp site, numerical and descriptive modelling are performed both for the deep bedrock and for the surface systems. The surface geology and regolith depth are important parameters for e.g. hydrogeological and geochemical modelling and for the over all understanding of the area. Regolith refers to all the unconsolidated deposits overlying the bedrock. The regolith depth model (RDM) presented here visualizes the stratigraphical distribution of the regolith as well as the elevation of the bedrock surface. The model covers 280 km2 including both terrestrial and marine areas. In the model the stratigraphy is represented by six layers (Z1-Z6) that corresponds to different types of regolith. The model is geometric and the properties of the layers are assigned by the user according to the purpose. The GeoModel program, which is an ArcGIS extension, was used for modelling the regolith depths. A detailed topographical Digital Elevation Model (DEM) and a map of Quaternary deposits were used as input to the model. Altogether 319 boreholes and 440 other stratigraphical observations were also used. Furthermore a large number of depth data interpreted from geophysical investigations were used; refraction seismic measurements from 51 profiles, 11,000 observation points from resistivity measurements and almost 140,000 points from seismic and sediment echo sounding data. The results from the refraction seismic and resistivity measurements give information about the total regolith depths, whereas most other data also give information about the stratigraphy of the regolith. Some of the used observations did not reach the bedrock surface. They do, however, describe the minimum regolith depth at each location and were therefore used where the regolith depth would have been thinner without using the observation point. A large proportion of the modelled area has a low data density and the area was therefore divided into nine domains. These domains were defined based on

  16. Testing the methodology for site descriptive modelling. Application for the Laxemar area

    International Nuclear Information System (INIS)

    Andersson, Johan; Berglund, Johan; Follin, Sven; Hakami, Eva; Halvarson, Jan; Hermanson, Jan; Laaksoharju, Marcus; Rhen, Ingvar; Wahlgren, C.H.

    2002-08-01

    A special project has been conducted where the currently available data from the Laxemar area, which is part of the Simpevarp site, have been evaluated and interpreted into a Site Descriptive Model covering: geology, hydrogeology, hydrogeochemistry and rock mechanics. Description of the surface ecosystem has been omitted, since it was re-characterised in another, parallel, project. Furthermore, there has been no evaluation of transport properties. The project is primarily a methodology test. The lessons learnt will be implemented in the Site Descriptive Modelling during the coming site investigation. The intent of the project has been to explore whether available methodology for Site Descriptive Modelling based on surface and borehole data is adequate and to identify potential needs for development and improvement in the methodology. The project has developed, with limitations in scope, a Site Descriptive Model in local scale, corresponding to the situation after completion of the Initial Site Investigations for the Laxemar area (i.e. 'version 1.2' using the vocabulary of the general execution program for the site investigations). The Site Descriptive Model should be reasonable, but should not be regarded as a 'real' model. There are limitations both in input data and in the scope of the analysis. The measured (primary) data constitute a wide range of different measurement results including data from two deep core drilled boreholes. These data both need to be checked for consistency and to be interpreted into a format more amenable for three-dimensional modelling. Examples of such evaluations are estimation of surface geology, lineament interpretation, geological single hole interpretation, hydrogeological single hole interpretation and assessment of hydrogeochemical data. Furthermore, while cross discipline interpretation is encouraged there is also a need for transparency. This means that the evaluations first are made within each discipline and after this

  17. Testing the methodology for site descriptive modelling. Application for the Laxemar area

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Johan [JA Streamflow AB, Aelvsjoe (Sweden); Berglund, Johan [SwedPower AB, Stockholm (Sweden); Follin, Sven [SF Geologic AB, Stockholm (Sweden); Hakami, Eva [Itasca Geomekanik AB, Stockholm (Sweden); Halvarson, Jan [Swedish Nuclear Fuel and Waste Management Co, Stockholm (Sweden); Hermanson, Jan [Golder Associates AB, Stockholm (Sweden); Laaksoharju, Marcus [Geopoint (Sweden); Rhen, Ingvar [Sweco VBB/VIAK, Stockholm (Sweden); Wahlgren, C.H. [Sveriges Geologiska Undersoekning, Uppsala (Sweden)

    2002-08-01

    A special project has been conducted where the currently available data from the Laxemar area, which is part of the Simpevarp site, have been evaluated and interpreted into a Site Descriptive Model covering: geology, hydrogeology, hydrogeochemistry and rock mechanics. Description of the surface ecosystem has been omitted, since it was re-characterised in another, parallel, project. Furthermore, there has been no evaluation of transport properties. The project is primarily a methodology test. The lessons learnt will be implemented in the Site Descriptive Modelling during the coming site investigation. The intent of the project has been to explore whether available methodology for Site Descriptive Modelling based on surface and borehole data is adequate and to identify potential needs for development and improvement in the methodology. The project has developed, with limitations in scope, a Site Descriptive Model in local scale, corresponding to the situation after completion of the Initial Site Investigations for the Laxemar area (i.e. 'version 1.2' using the vocabulary of the general execution program for the site investigations). The Site Descriptive Model should be reasonable, but should not be regarded as a 'real' model. There are limitations both in input data and in the scope of the analysis. The measured (primary) data constitute a wide range of different measurement results including data from two deep core drilled boreholes. These data both need to be checked for consistency and to be interpreted into a format more amenable for three-dimensional modelling. Examples of such evaluations are estimation of surface geology, lineament interpretation, geological single hole interpretation, hydrogeological single hole interpretation and assessment of hydrogeochemical data. Furthermore, while cross discipline interpretation is encouraged there is also a need for transparency. This means that the evaluations first are made within each discipline

  18. Application of the Rangeland Hydrology and Erosion Model to Ecological Site Descriptions and Management

    Science.gov (United States)

    The utility of Ecological Site Descriptions (ESDs) and State-and-Transition Models (STMs) concepts in guiding rangeland management hinges on their ability to accurately describe and predict community dynamics and the associated consequences. For many rangeland ecosystems, plant community dynamics ar...

  19. Study on the methodology for hydrogeological site descriptive modelling by discrete fracture networks

    International Nuclear Information System (INIS)

    Tanaka, Tatsuya; Ando, Kenichi; Hashimoto, Shuuji; Saegusa, Hiromitsu; Takeuchi, Shinji; Amano, Kenji

    2007-01-01

    This study aims to establish comprehensive techniques for site descriptive modelling considering the hydraulic heterogeneity due to the Water Conducting Features in fractured rocks. The WCFs was defined by the interpretation and integration of geological and hydrogeological data obtained from the deep borehole investigation campaign in the Mizunami URL project and Regional Hydrogeological Study. As a result of surface based investigation phase, the block-scale hydrogeological descriptive model was generated using hydraulic discrete fracture networks. Uncertainties and remaining issues associated with the assumption in interpreting the data and its modelling were addressed in a systematic way. (author)

  20. Explorative analysis of microbes, colloids and gases together with microbial modelling. Site description model SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Hallbeck, Lotta; Pedersen, Karsten (Microbial Analytics Sweden AB, Goeteborg (Sweden))

    2008-08-15

    The work has involved the development of descriptive and mathematical models for groundwaters in relation to rock domains, fracture domains and deformation zones. Past climate changes are the major driving force for hydrogeochemical changes and therefore of fundamental importance for understanding the palaeohydrogeological, palaeohydrogeochemical and present evolution of groundwater in the crystalline bedrock of the Fennoscandian Shield. Understanding current undisturbed hydrochemical conditions at the proposed repository site is important when predicting future changes in groundwater chemistry. The causes of copper corrosion and/or bentonite degradation are of particular interest as they may jeopardise the long-term integrity of the planned SKB repository system. Thus, the following variables are considered for the hydrogeochemical site descriptive modelling: pH, Eh, sulphur species, iron, manganese, carbonate, phosphate, nitrogen species, total dissolved solids (TDS), isotopes, colloids, fulvic and humic acids and microorganisms. In addition, dissolved gases (e.g. carbon dioxide, methane and hydrogen) are of interest because of their likely participation in microbial reactions. In this series of reports, the final hydrogeochemical evaluation work of the site investigation at the Laxemar site, is presented. The work was conducted by SKB's hydrogeochemical project group, ChemNet, which consists of independent consultants and Univ. researchers with expertise in geochemistry, hydrochemistry, hydrogeochemistry, microbiology, geomicrobiology, analytical chemistry etc. The resulting site descriptive model version, mainly based on available primary data from the extended data freeze L2.3 (Nov 2007). This report focuses on microbiology, colloids and gases. Several methods must be used to characterise active microbial communities in groundwater. Microbial parameters of interest are the total number of cells (TNC) and the presence of various metabolic groups of

  1. Explorative analysis of microbes, colloids and gases together with microbial modelling. Site description model SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Hallbeck, Lotta; Pedersen, Karsten

    2008-08-01

    The work has involved the development of descriptive and mathematical models for groundwaters in relation to rock domains, fracture domains and deformation zones. Past climate changes are the major driving force for hydrogeochemical changes and therefore of fundamental importance for understanding the palaeohydrogeological, palaeohydrogeochemical and present evolution of groundwater in the crystalline bedrock of the Fennoscandian Shield. Understanding current undisturbed hydrochemical conditions at the proposed repository site is important when predicting future changes in groundwater chemistry. The causes of copper corrosion and/or bentonite degradation are of particular interest as they may jeopardise the long-term integrity of the planned SKB repository system. Thus, the following variables are considered for the hydrogeochemical site descriptive modelling: pH, Eh, sulphur species, iron, manganese, carbonate, phosphate, nitrogen species, total dissolved solids (TDS), isotopes, colloids, fulvic and humic acids and microorganisms. In addition, dissolved gases (e.g. carbon dioxide, methane and hydrogen) are of interest because of their likely participation in microbial reactions. In this series of reports, the final hydrogeochemical evaluation work of the site investigation at the Laxemar site, is presented. The work was conducted by SKB's hydrogeochemical project group, ChemNet, which consists of independent consultants and Univ. researchers with expertise in geochemistry, hydrochemistry, hydrogeochemistry, microbiology, geomicrobiology, analytical chemistry etc. The resulting site descriptive model version, mainly based on available primary data from the extended data freeze L2.3 (Nov 2007). This report focuses on microbiology, colloids and gases. Several methods must be used to characterise active microbial communities in groundwater. Microbial parameters of interest are the total number of cells (TNC) and the presence of various metabolic groups of

  2. YUCCA MOUNTAIN SITE DESCRIPTION

    International Nuclear Information System (INIS)

    Simmons, A.M.

    2004-01-01

    The ''Yucca Mountain Site Description'' summarizes, in a single document, the current state of knowledge and understanding of the natural system at Yucca Mountain. It describes the geology; geochemistry; past, present, and projected future climate; regional hydrologic system; and flow and transport within the unsaturated and saturated zones at the site. In addition, it discusses factors affecting radionuclide transport, the effect of thermal loading on the natural system, and tectonic hazards. The ''Yucca Mountain Site Description'' is broad in nature. It summarizes investigations carried out as part of the Yucca Mountain Project since 1988, but it also includes work done at the site in earlier years, as well as studies performed by others. The document has been prepared under the Office of Civilian Radioactive Waste Management quality assurance program for the Yucca Mountain Project. Yucca Mountain is located in Nye County in southern Nevada. The site lies in the north-central part of the Basin and Range physiographic province, within the northernmost subprovince commonly referred to as the Great Basin. The basin and range physiography reflects the extensional tectonic regime that has affected the region during the middle and late Cenozoic Era. Yucca Mountain was initially selected for characterization, in part, because of its thick unsaturated zone, its arid to semiarid climate, and the existence of a rock type that would support excavation of stable openings. In 1987, the United States Congress directed that Yucca Mountain be the only site characterized to evaluate its suitability for development of a geologic repository for high-level radioactive waste and spent nuclear fuel

  3. YUCCA MOUNTAIN SITE DESCRIPTION

    Energy Technology Data Exchange (ETDEWEB)

    A.M. Simmons

    2004-04-16

    The ''Yucca Mountain Site Description'' summarizes, in a single document, the current state of knowledge and understanding of the natural system at Yucca Mountain. It describes the geology; geochemistry; past, present, and projected future climate; regional hydrologic system; and flow and transport within the unsaturated and saturated zones at the site. In addition, it discusses factors affecting radionuclide transport, the effect of thermal loading on the natural system, and tectonic hazards. The ''Yucca Mountain Site Description'' is broad in nature. It summarizes investigations carried out as part of the Yucca Mountain Project since 1988, but it also includes work done at the site in earlier years, as well as studies performed by others. The document has been prepared under the Office of Civilian Radioactive Waste Management quality assurance program for the Yucca Mountain Project. Yucca Mountain is located in Nye County in southern Nevada. The site lies in the north-central part of the Basin and Range physiographic province, within the northernmost subprovince commonly referred to as the Great Basin. The basin and range physiography reflects the extensional tectonic regime that has affected the region during the middle and late Cenozoic Era. Yucca Mountain was initially selected for characterization, in part, because of its thick unsaturated zone, its arid to semiarid climate, and the existence of a rock type that would support excavation of stable openings. In 1987, the United States Congress directed that Yucca Mountain be the only site characterized to evaluate its suitability for development of a geologic repository for high-level radioactive waste and spent nuclear fuel.

  4. Numerical modelling of surface hydrology and near-surface hydrogeology at Forsmark. Site descriptive modelling SDM. Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Bosson, Emma (Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)); Gustafsson, Lars-Goeran; Sassner, Mona (DHI Sverige AB, Stockholm (Sweden))

    2008-09-15

    SKB is currently performing site investigations at two potential sites for a final repository for spent nuclear fuel. This report presents results of water flow and solute transport modelling of the Forsmark site. The modelling reported in this document focused on the near-surface groundwater, i.e. groundwater in Quaternary deposits and shallow rock, and surface water systems, and was performed using the MIKE SHE tool. The most recent site data used in the modelling were delivered in the Forsmark 2.3 dataset, which had its 'data freeze' on March 31, 2007. The present modelling is performed in support of the final version of the Forsmark site description that is produced during the site investigation phase. In this work, the hydrological modelling system MIKE SHE has been used to describe near-surface groundwater flow and the contact between groundwater and surface water at the Forsmark site. The surface water system at Forsmark is described with the one-dimensional 'channel flow' modelling tool MIKE 11, which is fully and dynamically integrated with MIKE SHE. The MIKE SHE model was updated with data from the F2.3 data freeze. The main updates concerned the geological description of the saturated zone and the time series data on water levels and surface water discharges. The time series data used as input data and for calibration and validation was extended until the Forsmark 2.3 data freeze (March 31, 2007). The present work can be subdivided into the following four parts: 1. Update of the numerical flow model. 2. Sensitivity analysis and calibration of the model parameters. 3. Validation of the calibrated model, followed by evaluation and identification of discrepancies between measurements and model results. 4. Additional sensitivity analysis and calibration in order to resolve the problems identified in point three above. The main actions taken during the calibration can be summarised as follows: 1. The potential evapotranspiration was

  5. The limnic ecosystems at Forsmark and Laxemar-Simpevarp. Site descriptive modelling SDM-Site

    International Nuclear Information System (INIS)

    Norden, Sara; Soederbaeck, Bjoern; Andersson, Eva

    2008-11-01

    The overall objective of this report is to provide a thorough description of the limnic ecosystems at both Forsmark and Laxemar-Simpevarp. This information may be used in the Safety Assessment and as a basis for the Environmental Impact Assessment. Three aims were set up for the report: 1) to characterize and describe the limnic ecosystems today and in the past in the Forsmark and Laxemar-Simpevarp areas and compare these ecosystems with limnic ecosystems in other areas; 2) to evaluate and visualize major pools, fluxes and sinks of elements within the limnic ecosystems; and finally 3) to describe human impact on the limnic ecosystems. The report includes a thorough description of the lakes and streams in Forsmark and Laxemar-Simpevarp and covers the following areas: catchment area characteristics, hydrology, climate, sediment characteristics, physical characteristics of streams, habitat distribution in lakes, biotic components, water chemistry, comparisons with other lakes and streams in the region, and a historical description. Ecosystem models for carbon and mass balances for a number of elements have been calculated to further improve the understanding of the lake ecosystems. Important processes for the safety assessment are described and evaluated in the report. The Forsmark regional model area contains more than 20 permanent lakes and pools. All lakes are small and shallow, and are characterized as oligotrophic hardwater lakes. Calcareous soils in the area give rise to high calcium concentrations in the surface water, which in turn leads to high pH and low nutrient concentrations in water as phosphorus often co-precipitates with calcium. The shallow depths and moderate water colour permit photosynthesis in the entire benthic habitat of the lakes, and the bottoms are covered by dense stands of the macroalgae Chara sp. Moreover, many of the lakes also have a thick microbial mat (>10 cm), consisting of cyanobacteria and diatoms, in the benthic habitat. Fish in

  6. The limnic ecosystems at Forsmark and Laxemar-Simpevarp. Site descriptive modelling SDM-Site

    Energy Technology Data Exchange (ETDEWEB)

    Norden, Sara; Soederbaeck, Bjoern [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Andersson, Eva [SWECO, Stockholm (Sweden)

    2008-11-15

    The overall objective of this report is to provide a thorough description of the limnic ecosystems at both Forsmark and Laxemar-Simpevarp. This information may be used in the Safety Assessment and as a basis for the Environmental Impact Assessment. Three aims were set up for the report: 1) to characterize and describe the limnic ecosystems today and in the past in the Forsmark and Laxemar-Simpevarp areas and compare these ecosystems with limnic ecosystems in other areas; 2) to evaluate and visualize major pools, fluxes and sinks of elements within the limnic ecosystems; and finally 3) to describe human impact on the limnic ecosystems. The report includes a thorough description of the lakes and streams in Forsmark and Laxemar-Simpevarp and covers the following areas: catchment area characteristics, hydrology, climate, sediment characteristics, physical characteristics of streams, habitat distribution in lakes, biotic components, water chemistry, comparisons with other lakes and streams in the region, and a historical description. Ecosystem models for carbon and mass balances for a number of elements have been calculated to further improve the understanding of the lake ecosystems. Important processes for the safety assessment are described and evaluated in the report. The Forsmark regional model area contains more than 20 permanent lakes and pools. All lakes are small and shallow, and are characterized as oligotrophic hardwater lakes. Calcareous soils in the area give rise to high calcium concentrations in the surface water, which in turn leads to high pH and low nutrient concentrations in water as phosphorus often co-precipitates with calcium. The shallow depths and moderate water colour permit photosynthesis in the entire benthic habitat of the lakes, and the bottoms are covered by dense stands of the macroalgae Chara sp. Moreover, many of the lakes also have a thick microbial mat (>10 cm), consisting of cyanobacteria and diatoms, in the benthic habitat. Fish in

  7. Strategy for a Rock Mechanics Site Descriptive Model. Development and testing of the theoretical approach

    Energy Technology Data Exchange (ETDEWEB)

    Staub, Isabelle; Fredriksson, Anders; Outters, Nils [Golder Associates AB, Uppsala (Sweden)

    2002-05-01

    In the purpose of studying the possibilities of a Deep Repository for spent fuel, the Swedish Nuclear and Fuel Management Company (SKB) is currently planning for Site Investigations. Data collected from these Site Investigations are interpreted and analysed to achieve the full Site Description, which is built up of models from all the disciplines that are considered of importance for the Site Description. One of these models is the Rock Mechanical Descriptive Model,which would be developed for any site in hard crystalline rock, and is a combination and evaluation of the characterisation of rock mass by means of empirical relationships and a theoretical approach based on numerical modelling. The present report describes the theoretical approach. The characterisation of the mechanical properties of the rock mass, viewed as a unit consisting of intact rock and fractures, is achieved by numerical simulations with following input parameters: initial stresses, fracture geometry, distribution of rock mechanical properties, such as deformation and strength parameters, for the intact rock and for the fractures. The numerical modelling was performed with the two-dimensional code UDEC, and the rock block models were generated from 2D trace sections extracted from the 3D Discrete Fracture Network (DFN) model. Assumptions and uncertainties related to the set-up of the model are considered. The numerical model was set-up to simulate a plain strain-loading test. Different boundary conditions were applied on the model for simulating stress conditions (I) in the undisturbed rock mass, and (II) at the proximity of a tunnel. In order to assess the reliability of the model sensitivity analyses have been conducted on some rock block models for defining the dependency of mechanical properties to in situ stresses, the influence of boundary conditions, rock material and joint constitutive models used to simulate the behaviour of intact rock and fractures, domain size and anisotropy. To

  8. Strategy for a Rock Mechanics Site Descriptive Model. Development and testing of the theoretical approach

    International Nuclear Information System (INIS)

    Staub, Isabelle; Fredriksson, Anders; Outters, Nils

    2002-05-01

    In the purpose of studying the possibilities of a Deep Repository for spent fuel, the Swedish Nuclear and Fuel Management Company (SKB) is currently planning for Site Investigations. Data collected from these Site Investigations are interpreted and analysed to achieve the full Site Description, which is built up of models from all the disciplines that are considered of importance for the Site Description. One of these models is the Rock Mechanical Descriptive Model,which would be developed for any site in hard crystalline rock, and is a combination and evaluation of the characterisation of rock mass by means of empirical relationships and a theoretical approach based on numerical modelling. The present report describes the theoretical approach. The characterisation of the mechanical properties of the rock mass, viewed as a unit consisting of intact rock and fractures, is achieved by numerical simulations with following input parameters: initial stresses, fracture geometry, distribution of rock mechanical properties, such as deformation and strength parameters, for the intact rock and for the fractures. The numerical modelling was performed with the two-dimensional code UDEC, and the rock block models were generated from 2D trace sections extracted from the 3D Discrete Fracture Network (DFN) model. Assumptions and uncertainties related to the set-up of the model are considered. The numerical model was set-up to simulate a plain strain-loading test. Different boundary conditions were applied on the model for simulating stress conditions (I) in the undisturbed rock mass, and (II) at the proximity of a tunnel. In order to assess the reliability of the model sensitivity analyses have been conducted on some rock block models for defining the dependency of mechanical properties to in situ stresses, the influence of boundary conditions, rock material and joint constitutive models used to simulate the behaviour of intact rock and fractures, domain size and anisotropy. To

  9. Hydrochemistry in surface water and shallow groundwater. Site descriptive modelling SDM-Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Troejbom, Mats (Mopelikan, Norrtaelje (SE)); Soederbaeck, Bjoern (Swedish Nuclear Fuel and Waste Management Co., Stockholm (SE)); Johansson, Per-Olof (Artesia Grundvattenkonsult AB, Taeby (SE))

    2007-10-15

    With a mathematical/statistical approach, a large number of visualisations and models reflect the hydrochemistry in the Forsmark area, with the intention to give an understanding of important processes and factors that affect the hydrochemistry in the surface systems. In order to widen the perspective, all data from the Forsmark 2.2 stage including observations from different levels of the bedrock, as well as hydrological measurements and characterisations of the Quaternary deposits, have been included in the analyses. The purpose of this report is to give a general understanding of the site and to explain observed overall patterns as well as anomalies, and, ultimately, to present a conceptual model that explains the present hydrochemistry in the surface system in the light of the past. The report may also function as a basis for further evaluation and testing of scenarios, and may be regarded as an intermediate step between raw data compilations from the vast SICADA database and specialised expert models. The flat topography and the recent withdrawal of the Baltic Sea due to the isostatic land-uplift are two important factors determining the hydrochemistry in the Forsmark area. Marine remnants in the Quaternary deposits, as well as modern sea water intrusions, are therefore strongly influencing the hydrochemistry, especially in areas at low altitude close to the coast. Large-scale marine gradients in the surface system are consistent with the conceptual model that describes the hydrochemical evolution in a paleo-hydrologic perspective. The Forsmark area is covered by glacial remnants, mostly in the form of a till layer, which was deposited during the Weichselian glaciation and deglaciation. When the ice cover retreated about 11,000 years ago, these deposits were exposed on the sea floor. This till layer is characterized by a rich content of calcite, originating from the sedimentary bedrock of Gaevlebukten about 100 km north of Forsmark. The dissolution of this

  10. Hydrochemistry in surface water and shallow groundwater. Site descriptive modelling SDM-Site Forsmark

    International Nuclear Information System (INIS)

    Troejbom, Mats; Soederbaeck, Bjoern; Johansson, Per-Olof

    2007-10-01

    With a mathematical/statistical approach, a large number of visualisations and models reflect the hydrochemistry in the Forsmark area, with the intention to give an understanding of important processes and factors that affect the hydrochemistry in the surface systems. In order to widen the perspective, all data from the Forsmark 2.2 stage including observations from different levels of the bedrock, as well as hydrological measurements and characterisations of the Quaternary deposits, have been included in the analyses. The purpose of this report is to give a general understanding of the site and to explain observed overall patterns as well as anomalies, and, ultimately, to present a conceptual model that explains the present hydrochemistry in the surface system in the light of the past. The report may also function as a basis for further evaluation and testing of scenarios, and may be regarded as an intermediate step between raw data compilations from the vast SICADA database and specialised expert models. The flat topography and the recent withdrawal of the Baltic Sea due to the isostatic land-uplift are two important factors determining the hydrochemistry in the Forsmark area. Marine remnants in the Quaternary deposits, as well as modern sea water intrusions, are therefore strongly influencing the hydrochemistry, especially in areas at low altitude close to the coast. Large-scale marine gradients in the surface system are consistent with the conceptual model that describes the hydrochemical evolution in a paleo-hydrologic perspective. The Forsmark area is covered by glacial remnants, mostly in the form of a till layer, which was deposited during the Weichselian glaciation and deglaciation. When the ice cover retreated about 11,000 years ago, these deposits were exposed on the sea floor. This till layer is characterized by a rich content of calcite, originating from the sedimentary bedrock of Gaevlebukten about 100 km north of Forsmark. The dissolution of this

  11. Hydrochemistry in surface water and shallow groundwater. Site descriptive modelling SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Troejbom, Mats (Mopelikan, Norrtaelje (Sweden)); Soederbaeck, Bjoern; Kalinowski, Birgitta (Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden))

    2008-10-15

    Based on a mathematical/statistical approach, a large number of visualisations and models reflect the hydrochemistry of the Laxemar-Simpevarp area, with the intention of providing an understanding of important processes and factors that affect the hydrochemistry of the surface systems. In order to widen the perspective, all data from Laxemar stage 2.3, including observations from different levels of the bedrock, as well as hydrological measurements and characterisations of the Quaternary deposits, have been included in the analyses. The purpose of this report is to provide a general understanding of the site and to explain observed overall patterns and anomalies, and ultimately to present a conceptual model that explains the present hydrochemistry of the surface system in the light of the past. The report may also serve as a basis for further evaluation and testing of scenarios, and may be regarded as an intermediate step between raw data compilations from the vast Sicada database and specialised expert models. The topography in the Laxemar-Simpevarp area is characterised by elevated areas covered by thin or no Quaternary deposits, intersected by deep fissure valleys filled with thick sediments. This topography, in combination with the withdrawal of the Baltic Sea due to isostatic land uplift, are two important factors determining the hydrochemistry of the Laxemar-Simpevarp area. Furthermore, marine remnants in the Quaternary deposits influence the hydrochemistry in areas at low elevation close to the coast, whereas higher-lying areas are mostly influenced by atmospheric deposition and weathering processes. The vegetation cover has also great impact on the hydrochemistry of the surface system. Degradation of biogenic carbon generates large numbers of H+ ions, which drive weathering processes in the Quaternary deposits as well as in the upper parts of the bedrock. The present situation in the surface system is a consequence of the palaeohydrological past. In higher

  12. Hydrochemistry in surface water and shallow groundwater. Site descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Troejbom, Mats; Soederbaeck, Bjoern; Kalinowski, Birgitta

    2008-10-01

    Based on a mathematical/statistical approach, a large number of visualisations and models reflect the hydrochemistry of the Laxemar-Simpevarp area, with the intention of providing an understanding of important processes and factors that affect the hydrochemistry of the surface systems. In order to widen the perspective, all data from Laxemar stage 2.3, including observations from different levels of the bedrock, as well as hydrological measurements and characterisations of the Quaternary deposits, have been included in the analyses. The purpose of this report is to provide a general understanding of the site and to explain observed overall patterns and anomalies, and ultimately to present a conceptual model that explains the present hydrochemistry of the surface system in the light of the past. The report may also serve as a basis for further evaluation and testing of scenarios, and may be regarded as an intermediate step between raw data compilations from the vast Sicada database and specialised expert models. The topography in the Laxemar-Simpevarp area is characterised by elevated areas covered by thin or no Quaternary deposits, intersected by deep fissure valleys filled with thick sediments. This topography, in combination with the withdrawal of the Baltic Sea due to isostatic land uplift, are two important factors determining the hydrochemistry of the Laxemar-Simpevarp area. Furthermore, marine remnants in the Quaternary deposits influence the hydrochemistry in areas at low elevation close to the coast, whereas higher-lying areas are mostly influenced by atmospheric deposition and weathering processes. The vegetation cover has also great impact on the hydrochemistry of the surface system. Degradation of biogenic carbon generates large numbers of H + ions, which drive weathering processes in the Quaternary deposits as well as in the upper parts of the bedrock. The present situation in the surface system is a consequence of the palaeohydrological past. In higher

  13. The terrestrial ecosystems at Forsmark and Laxemar-Simpevarp. Site descriptive modelling SDM site

    Energy Technology Data Exchange (ETDEWEB)

    Loefgren, Anders [EcoAnalytica, Haegersten (Sweden); ed.

    2008-12-15

    This report describes the terrestrial ecosystems in the Forsmark and Laxemar-Simpevarp areas by summarizing ecological data and data from disciplines such as hydrology, quaternary geology and chemistry. The description therefore includes a number of different processes that drive element fluxes in the ecosystems, such as net primary production, heterotrophic respiration, transpiration, and horizontal transport from land to streams and lakes. Moreover, the human appropriation of the landscape is described with regard to land use and potential and actual utilization of food resources both today and in a historical perspective

  14. The terrestrial ecosystems at Forsmark and Laxemar-Simpevarp. Site descriptive modelling SDM site

    International Nuclear Information System (INIS)

    Loefgren, Anders

    2008-12-01

    This report describes the terrestrial ecosystems in the Forsmark and Laxemar-Simpevarp areas by summarizing ecological data and data from disciplines such as hydrology, quaternary geology and chemistry. The description therefore includes a number of different processes that drive element fluxes in the ecosystems, such as net primary production, heterotrophic respiration, transpiration, and horizontal transport from land to streams and lakes. Moreover, the human appropriation of the landscape is described with regard to land use and potential and actual utilization of food resources both today and in a historical perspective

  15. Preliminary site description: Groundwater flow simulations. Simpevarp area (version 1.1) modelled with CONNECTFLOW

    International Nuclear Information System (INIS)

    Hartley, Lee; Worth, David; Gylling, Bjoern; Marsic, Niko; Holmen, Johan

    2004-08-01

    The main objective of this study is to assess the role of known and unknown hydrogeological conditions for the present-day distribution of saline groundwater at the Simpevarp and Laxemar sites. An improved understanding of the paleo-hydrogeology is necessary in order to gain credibility for the Site Descriptive Model in general and the Site Hydrogeological Description in particular. This is to serve as a basis for describing the present hydrogeological conditions as well as predictions of future hydrogeological conditions. This objective implies a testing of: geometrical alternatives in the structural geology and bedrock fracturing, variants in the initial and boundary conditions, and parameter uncertainties (i.e. uncertainties in the hydraulic property assignment). This testing is necessary in order to evaluate the impact on the groundwater flow field of the specified components and to promote proposals of further investigations of the hydrogeological conditions at the site. The general methodology for modelling transient salt transport and groundwater flow using CONNECTFLOW that was developed for Forsmark has been applied successfully also for Simpevarp. Because of time constraints only a key set of variants were performed that focussed on the influences of DFN model parameters, the kinematic porosity, and the initial condition. Salinity data in deep boreholes available at the time of the project was too limited to allow a good calibration exercise. However, the model predictions are compared with the available data from KLX01 and KLX02 below. Once more salinity data is available it may be possible to draw more definite conclusions based on the differences between variants. At the moment though the differences should just be used understand the sensitivity of the models to various input parameters

  16. Digital elevation models for site investigation programme in Oskarshamn. Site description version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Brydsten, Lars; Stroemgren, Maarten [Umeaa Univ. (Sweden). Dept. of Biology and Environmental Science

    2005-06-01

    In the Oskarshamn area, a digital elevation model has been produced using elevation data from many elevation sources on both land and sea. Many elevation model users are only interested in elevation models over land, so the model has been designed in three versions: Version 1 describes land surface, lake water surface, and sea bottom. Version 2 describes land surface, sediment levels at lake bottoms, and sea bottoms. Version 3 describes land surface, sediment levels at lake bottoms, and sea surface. In cases where the different sources of data were not in point form 'such as existing elevation models of land or depth lines from nautical charts' they have been converted to point values using GIS software. Because data from some sources often overlaps with data from other sources, several tests were conducted to determine if both sources of data or only one source would be included in the dataset used for the interpolation procedure. The tests resulted in the decision to use only the source judged to be of highest quality for most areas with overlapping data sources. All data were combined into a database of approximately 3.3 million points unevenly spread over an area of about 800 km{sup 2}. The large number of data points made it difficult to construct the model with a single interpolation procedure, the area was divided into 28 sub-models that were processed one by one and finally merged together into one single model. The software ArcGis 8.3 and its extension Geostatistical Analysis were used for the interpolation. The Ordinary Kriging method was used for interpolation. This method allows both a cross validation and a validation before the interpolation is conducted. Cross validation with different Kriging parameters were performed and the model with the most reasonable statistics was chosen. Finally, a validation with the most appropriate Kriging parameters was performed in order to verify that the model fit unmeasured localities. Since both the

  17. Digital elevation models for site investigation programme in Oskarshamn. Site description version 1.2

    International Nuclear Information System (INIS)

    Brydsten, Lars; Stroemgren, Maarten

    2005-06-01

    In the Oskarshamn area, a digital elevation model has been produced using elevation data from many elevation sources on both land and sea. Many elevation model users are only interested in elevation models over land, so the model has been designed in three versions: Version 1 describes land surface, lake water surface, and sea bottom. Version 2 describes land surface, sediment levels at lake bottoms, and sea bottoms. Version 3 describes land surface, sediment levels at lake bottoms, and sea surface. In cases where the different sources of data were not in point form 'such as existing elevation models of land or depth lines from nautical charts' they have been converted to point values using GIS software. Because data from some sources often overlaps with data from other sources, several tests were conducted to determine if both sources of data or only one source would be included in the dataset used for the interpolation procedure. The tests resulted in the decision to use only the source judged to be of highest quality for most areas with overlapping data sources. All data were combined into a database of approximately 3.3 million points unevenly spread over an area of about 800 km 2 . The large number of data points made it difficult to construct the model with a single interpolation procedure, the area was divided into 28 sub-models that were processed one by one and finally merged together into one single model. The software ArcGis 8.3 and its extension Geostatistical Analysis were used for the interpolation. The Ordinary Kriging method was used for interpolation. This method allows both a cross validation and a validation before the interpolation is conducted. Cross validation with different Kriging parameters were performed and the model with the most reasonable statistics was chosen. Finally, a validation with the most appropriate Kriging parameters was performed in order to verify that the model fit unmeasured localities. Since both the quality and the

  18. Methodology for geometric modelling. Presentation and administration of site descriptive models; Metodik foer geometrisk modellering. Presentation och administration av platsbeskrivande modeller

    Energy Technology Data Exchange (ETDEWEB)

    Munier, Raymond [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Hermanson, Jan [Golder Associates (Sweden)

    2001-03-01

    This report presents a methodology to construct, visualise and present geoscientific descriptive models based on data from the site investigations, which the SKB currently performs, to build an underground nuclear waste disposal facility in Sweden. It is designed for interaction with SICADA (SKB:s site characterisation database) and RVS (SKB:s Rock Visualisation System). However, the concepts of the methodology are general and can be used with other tools capable of handling 3D geometries and parameters. The descriptive model is intended to be an instrument where site investigation data from all disciplines are put together to form a comprehensive visual interpretation of the studied rock mass. The methodology has four main components: 1. Construction of a geometrical model of the interpreted main structures at the site. 2. Description of the geoscientific characteristics of the structures. 3. Description and geometrical implementation of the geometric uncertainties in the interpreted model structures. 4. Quality system for the handling of the geometrical model, its associated database and some aspects of the technical auditing. The geometrical model forms a basis for understanding the main elements and structures of the investigated site. Once the interpreted geometries are in place in the model, the system allows for adding descriptive and quantitative data to each modelled object through a system of intuitive menus. The associated database allows each geometrical object a complete quantitative description of all geoscientific disciplines, variabilities, uncertainties in interpretation and full version history. The complete geometrical model and its associated database of object descriptions are to be recorded in a central quality system. Official, new and old versions of the model are administered centrally in order to have complete quality assurance of each step in the interpretation process. The descriptive model is a cornerstone in the understanding of the

  19. Thermal modelling. Preliminary site description. Forsmark area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Sundberg, Jan; Back, Paer-Erik; Bengtsson, Anna; Laendell, Maerta [Geo Innova AB, Linkoeping (Sweden)

    2005-08-01

    This report presents the thermal site descriptive model for the Forsmark area, version 1.2. The main objective of this report is to present the thermal modelling work where data has been identified, quality controlled, evaluated and summarised in order to make an upscaling to lithological domain level possible. The thermal conductivity at canister scale has been modelled for two different lithological domains (RFM029 and RFM012, both dominated by granite to granodiorite (101057)). A main modelling approach has been used to determine the mean value of the thermal conductivity. Two alternative/complementary approaches have been used to evaluate the spatial variability of the thermal conductivity at domain level. The thermal modelling approaches are based on the lithological model for the Forsmark area, version 1.2 together with rock type models constituted from measured and calculated (from mineral composition) thermal conductivities. Results indicate that the mean of thermal conductivity is expected to exhibit a small variation between the different domains, 3.46 W/(mxK) for RFM012 to 3.55 W/(mxK) for RFM029. The spatial distribution of the thermal conductivity does not follow a simple model. Lower and upper 95% confidence limits are based on the modelling results, but have been rounded of to only two significant figures. Consequently, the lower limit is 2.9 W/(mxK), while the upper is 3.8 W/(mxK). This is applicable to both the investigated domains. The temperature dependence is rather small with a decrease in thermal conductivity of 10.0% per 100 deg C increase in temperature for the dominating rock type. There are a number of important uncertainties associated with these results. One of the uncertainties considers the representative scale for the canister. Another important uncertainty is the methodological uncertainties associated with the upscaling of thermal conductivity from cm-scale to canister scale. In addition, the representativeness of rock samples is

  20. Hydrogeochemical evaluation for Simpevarp model version 1.2. Preliminary site description of the Simpevarp area

    International Nuclear Information System (INIS)

    Laaksoharju, Marcus

    2004-12-01

    to Type C groundwaters. Main reactions involve water/rock interaction for long residence non-marine brines driven by diffusion. A modelling approach was used to simulate the composition of the highly saline or brine groundwaters and, in the Simpevarp area, concluded that mixing is the main irreversible process. It controls chloride concentration that, in turn, determines the re-equilibrium path (water-rock interaction) triggered by mixing. Coupled transport modelling was used to model the groundwater age, tritium content and calcite dissolution/precipitation processes at shallow groundwater depths at both Laxemar and Simpevarp. The modelled results provide additional support to hydrogeological models by using independent hydrochemical information and added support to the general hydrogeochemical understanding of the site. In this evaluation the groundwater model has been updated, the salinity distribution, mixing processes and the major reactions altering the groundwaters have been modelled down to a depth of 1000 m, and an updated Hydrogeochemical Site Descriptive Model version 1.2 has been produced. More groundwater and isotopic data, together with microbial information, colloids and gases, provided additional site descriptive information. Finally, the introduction of coupled modelling provided additional possibilities to address independently the various processes in question

  1. Comparison of site descriptive models for Olkiluoto, Finland and Forsmark, Sweden

    Energy Technology Data Exchange (ETDEWEB)

    Geier, J.; Bath, A.; Stephansson, O.; Luukkonen, A.

    2012-08-15

    The proposed high-level radioactive waste repository sites at Olkiluoto and Forsmark share broadly similar geologic histories and regional settings. Despite differences in lithology, rock strength and patterns of brittle deformation, the sites show similarities in terms of hydrogeochemistry and hydrogeology. These similarities reflect a dominating influence of saline and brackish water intrusion during inundation by the postglacial Littorina Sea and Baltic Sea, followed by exposure to meteoric waters following postglacial uplift and transition to a Baltic coastal setting. Both sites also contain deep bedrock saline groundwater, though this is more evident at Olkiluoto than at Forsmark. A comparative study of site descriptive models for the two sites identifies the following key differences that could potentially impact safety of a repository: (1) Redox controls, buffering and biogeochemistry at proposed repository depths; (2) Salinity gradients at and below proposed repository depths; (3) Methane concentrations at and below proposed repository depths; (4) Depths to which glacial water and Littorina water penetrated; (5) Cation hydrogeochemistry and water-rock reaction; (6) Pore water compositions in rock matrix; (7) Rock fabric, secondary minerals and alteration with respect to radionuclide retention; (8) Brittle deformation fabric differences on multiple scales that affect vertical hydraulic conductivity; (9) Differences in apparent frequency of encountering water-conducting networks at proposed repository depths; (10) Shallow bedrock hydraulic properties; (11) Unique intrusive or dissolution features; (12) Connectivity of site-scale models to regional-scale features; (13) Mesoproterozoic rocks in vicinity and possibilities for human-intrusion scenarios; (14) Rock stresses and bedrock strength and deformability at proposed repository depths; (15) Thermal anisotropy. These differences are all potentially significant to safety functions, but none are so severe that

  2. Rock Mechanics Forsmark. Site descriptive modelling Forsmark stage 2.2

    Energy Technology Data Exchange (ETDEWEB)

    Glamheden, Rune; Fredriksson, Anders (Golder Associates AB (SE)); Roeshoff, Kennert; Karlsson, Johan (Berg Bygg Konsult AB (SE)); Hakami, Hossein (Itasca Geomekanik AB (SE)); Christiansson, Rolf (Swedish Nuclear Fuel and Waste Management Co., Stockholm (SE))

    2007-12-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterisation at two different locations, Forsmark and Laxemar/Simpevarp, with the objective of siting a geological repository for spent nuclear fuel. The characterisation of a site is an integrated work carried out by several disciplines including geology, rock mechanics, thermal properties, hydrogeology, hydrogeochemistry and surface systems. This report presents the rock mechanics model of the Forsmark site up to stage 2.2. The scope of work has included compilation and analysis of primary data of intact rock and fractures, estimation of the rock mass mechanical properties and estimation of the in situ state of stress at the Forsmark site. The laboratory results on intact rock and fractures in the target volume demonstrate a good quality rock mass that is strong, stiff and relatively homogeneous. The homogeneity is also supported by the lithological and the hydrogeological models. The properties of the rock mass have been initially estimated by two separate modelling approaches, one empirical and one theoretical. An overall final estimate of the rock mass properties were achieved by integrating the results from the two models via a process termed 'Harmonization'. Both the tensile tests, carried out perpendicular and parallel to the foliation, and the theoretical analyses of the rock mass properties in directions parallel and perpendicular to the major principal stress, result in parameter values almost independent of direction. This indicates that the rock mass in the target volume is isotropic. The rock mass quality in the target volume appears to be of high and uniform quality. Those portions with reduced rock mass quality that do exist are mainly related to sections with increased fracture frequency. Such sections are associated with deformation zones according to the geological description. The results of adjacent rock domains and fracture domains of the target

  3. Hydrogeological DFN modelling using structural and hydraulic data from KLX04. Preliminary site description Laxemar subarea - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Follin, Sven [SF GeoLogic AB, Taeby (Sweden); Stigsson, Martin [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Svensson, Urban [Computer-aided Fluid Engineering AB, Norrkoeping (Sweden)

    2006-04-15

    SKB is conducting site investigations for a high-level nuclear waste repository in fractured crystalline rocks at two coastal areas in Sweden. The two candidate areas are named Forsmark and Simpevarp. The site characterisation work is divided into two phases, an initial site investigation phase (ISI) and a complete site investigation phase (CSI). The results of the ISI phase are used as a basis for deciding on the subsequent CSI phase. On the basis of the CSI investigations a decision is made as to whether detailed characterisation will be performed (including sinking of a shaft). An integrated component in the site characterisation work is the development of site descriptive models. These comprise basic models in three dimensions with an accompanying text description. Central in the modelling work is the geological model which provides the geometrical context in terms of a model of deformation zones and the less fractured rock mass between the zones. Using the geological and geometrical description models as a basis, descriptive models for other disciplines (surface ecosystems, hydrogeology, hydrogeochemistry, rock mechanics, thermal properties and transport properties) will be developed. Great care is taken to arrive at a general consistency in the description of the various models and assessment of uncertainty and possible needs of alternative models. The main objective of this study is to support the development of a hydrogeological DFN model (Discrete Fracture Network) for the Preliminary Site Description of the Laxemar area on a regional-scale (SDM version L1.2). A more specific objective of this study is to assess the propagation of uncertainties in the geological DFN modelling reported for L1.2 into the groundwater flow modelling. An improved understanding is necessary in order to gain credibility for the Site Description in general and the hydrogeological description in particular. The latter will serve as a basis for describing the present

  4. Hydrogeological DFN modelling using structural and hydraulic data from KLX04. Preliminary site description Laxemar subarea - version 1.2

    International Nuclear Information System (INIS)

    Follin, Sven; Stigsson, Martin; Svensson, Urban

    2006-04-01

    SKB is conducting site investigations for a high-level nuclear waste repository in fractured crystalline rocks at two coastal areas in Sweden. The two candidate areas are named Forsmark and Simpevarp. The site characterisation work is divided into two phases, an initial site investigation phase (ISI) and a complete site investigation phase (CSI). The results of the ISI phase are used as a basis for deciding on the subsequent CSI phase. On the basis of the CSI investigations a decision is made as to whether detailed characterisation will be performed (including sinking of a shaft). An integrated component in the site characterisation work is the development of site descriptive models. These comprise basic models in three dimensions with an accompanying text description. Central in the modelling work is the geological model which provides the geometrical context in terms of a model of deformation zones and the less fractured rock mass between the zones. Using the geological and geometrical description models as a basis, descriptive models for other disciplines (surface ecosystems, hydrogeology, hydrogeochemistry, rock mechanics, thermal properties and transport properties) will be developed. Great care is taken to arrive at a general consistency in the description of the various models and assessment of uncertainty and possible needs of alternative models. The main objective of this study is to support the development of a hydrogeological DFN model (Discrete Fracture Network) for the Preliminary Site Description of the Laxemar area on a regional-scale (SDM version L1.2). A more specific objective of this study is to assess the propagation of uncertainties in the geological DFN modelling reported for L1.2 into the groundwater flow modelling. An improved understanding is necessary in order to gain credibility for the Site Description in general and the hydrogeological description in particular. The latter will serve as a basis for describing the present

  5. Thermal modelling. Preliminary site description Simpevarp subarea - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Sundberg, Jan; Back, Paer-Erik; Bengtsson, Anna; Laendell, Maerta [Geo Innova AB, Linkoeping (Sweden)

    2005-08-15

    This report presents the thermal site descriptive model for the Simpevarp subarea, version 1.2. The main objective of this report is to present the thermal modelling work where data has been identified, quality controlled, evaluated and summarised in order to make an upscaling to lithological domain level possible. The thermal conductivity at possible canister scale has been modelled for four different lithological domains (RSMA01 (Aevroe granite), RSMB01 (Fine-grained dioritoid), RSMC01 (mixture of Aevroe granite and Quartz monzodiorite), and RSMD01 (Quartz monzodiorite)). A main modelling approach has been used to determine the mean value of the thermal conductivity. Three alternative/complementary approaches have been used to evaluate the spatial variability of the thermal conductivity at domain level. The thermal modelling approaches are based on the lithological model for the Simpevarp subarea, version 1.2 together with rock type models constituted from measured and calculated (from mineral composition) thermal conductivities. For one rock type, the Aevroe granite (501044), density loggings within the specific rock type has also been used in the domain modelling in order to consider the spatial variability within the Aevroe granite. This has been possible due to the presented relationship between density and thermal conductivity, valid for the Aevroe granite. Results indicate that the mean of thermal conductivity is expected to exhibit only a small variation between the different domains, from 2.62 W/(m.K) to 2.80 W/(m.K). The standard deviation varies according to the scale considered and for the canister scale it is expected to range from 0.20 to 0.28 W/(m.K). Consequently, the lower confidence limit (95% confidence) for the canister scale is within the range 2.04-2.35 W/(m.K) for the different domains. The temperature dependence is rather small with a decrease in thermal conductivity of 1.1-3.4% per 100 deg C increase in temperature for the dominating rock

  6. Thermal modelling. Preliminary site description Simpevarp subarea - version 1.2

    International Nuclear Information System (INIS)

    Sundberg, Jan; Back, Paer-Erik; Bengtsson, Anna; Laendell, Maerta

    2005-08-01

    This report presents the thermal site descriptive model for the Simpevarp subarea, version 1.2. The main objective of this report is to present the thermal modelling work where data has been identified, quality controlled, evaluated and summarised in order to make an upscaling to lithological domain level possible. The thermal conductivity at possible canister scale has been modelled for four different lithological domains (RSMA01 (Aevroe granite), RSMB01 (Fine-grained dioritoid), RSMC01 (mixture of Aevroe granite and Quartz monzodiorite), and RSMD01 (Quartz monzodiorite)). A main modelling approach has been used to determine the mean value of the thermal conductivity. Three alternative/complementary approaches have been used to evaluate the spatial variability of the thermal conductivity at domain level. The thermal modelling approaches are based on the lithological model for the Simpevarp subarea, version 1.2 together with rock type models constituted from measured and calculated (from mineral composition) thermal conductivities. For one rock type, the Aevroe granite (501044), density loggings within the specific rock type has also been used in the domain modelling in order to consider the spatial variability within the Aevroe granite. This has been possible due to the presented relationship between density and thermal conductivity, valid for the Aevroe granite. Results indicate that the mean of thermal conductivity is expected to exhibit only a small variation between the different domains, from 2.62 W/(m.K) to 2.80 W/(m.K). The standard deviation varies according to the scale considered and for the canister scale it is expected to range from 0.20 to 0.28 W/(m.K). Consequently, the lower confidence limit (95% confidence) for the canister scale is within the range 2.04-2.35 W/(m.K) for the different domains. The temperature dependence is rather small with a decrease in thermal conductivity of 1.1-3.4% per 100 deg C increase in temperature for the dominating rock

  7. Statistics of modelled conductive fractures based on Laxemar and Forsmark. Site descriptive model data

    Energy Technology Data Exchange (ETDEWEB)

    Stigsson, Martin

    2009-12-15

    The objectives of this report is to investigate the frequency of fractures assumed to be water conductive, i.e. open or partly open and directly or indirectly connected to a source. Also the distribution of total transmissivity in 100 m and 20 m horizontal sections and 8 m vertical sections is calculated. The report is only intended to serve as input to the SER, Site Engineering Report, at Laxemar and Forsmark. The input data for the analyses is taken, as is, from the Discrete Fracture Network sections in published reports. No evaluation that the model parameters are appropriate for the task or sensitivity analysis is performed. The tunnels and deposition holes are modelled as scanlines which is a very coarse approximation, but it may give some rough estimation of the frequency of the water bearing features, especially for the larger ones, and the total transmissivity in a section

  8. Statistics of modelled conductive fractures based on Laxemar and Forsmark. Site descriptive model data

    International Nuclear Information System (INIS)

    Stigsson, Martin

    2009-12-01

    The objectives of this report is to investigate the frequency of fractures assumed to be water conductive, i.e. open or partly open and directly or indirectly connected to a source. Also the distribution of total transmissivity in 100 m and 20 m horizontal sections and 8 m vertical sections is calculated. The report is only intended to serve as input to the SER, Site Engineering Report, at Laxemar and Forsmark. The input data for the analyses is taken, as is, from the Discrete Fracture Network sections in published reports. No evaluation that the model parameters are appropriate for the task or sensitivity analysis is performed. The tunnels and deposition holes are modelled as scanlines which is a very coarse approximation, but it may give some rough estimation of the frequency of the water bearing features, especially for the larger ones, and the total transmissivity in a section

  9. Numerical modelling of solute transport at Forsmark with MIKE SHE. Site descriptive modelling SDM-Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Gustafsson, Lars-Goeran; Sassner, Mona (DHI Sverige AB, Stockholm (Sweden)); Bosson, Emma (Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden))

    2008-12-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is performing site investigations at two different locations in Sweden, referred to as the Forsmark and Laxemar areas, with the objective of siting a final repository for high-level radioactive waste. Data from the site investigations are used in a variety of modelling activities. This report presents model development and results of numerical transport modelling based on the numerical flow modelling of surface water and near-surface groundwater at the Forsmark site. The numerical modelling was performed using the modelling tool MIKE SHE and is based on the site data and conceptual model of the Forsmark areas. This report presents solute transport applications based on both particle tracking simulations and advection-dispersion calculations. The MIKE SHE model is the basis for the transport modelling presented in this report. Simulation cases relevant for the transport from a deep geological repository have been studied, but also the pattern of near surface recharge and discharge areas. When the main part of the modelling work presented in this report was carried out, the flow modelling of the Forsmark site was not finalised. Thus, the focus of this work is to describe the sensitivity to different transport parameters, and not to point out specific areas as discharge areas from a future repository (this is to be done later, within the framework of the safety assessment). In the last chapter, however, results based on simulations with the re-calibrated MIKE SHE flow model are presented. The results from the MIKE SHE water movement calculations were used by cycling the calculated transient flow field for a selected one-year period as many times as needed to achieve the desired simulation period. The solute source was located either in the bedrock or on top of the model. In total, 15 different transport simulation cases were studied. Five of the simulations were particle tracking simulations, whereas the rest

  10. Numerical modelling of solute transport at Forsmark with MIKE SHE. Site descriptive modelling SDM-Site Forsmark

    International Nuclear Information System (INIS)

    Gustafsson, Lars-Goeran; Sassner, Mona; Bosson, Emma

    2008-12-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is performing site investigations at two different locations in Sweden, referred to as the Forsmark and Laxemar areas, with the objective of siting a final repository for high-level radioactive waste. Data from the site investigations are used in a variety of modelling activities. This report presents model development and results of numerical transport modelling based on the numerical flow modelling of surface water and near-surface groundwater at the Forsmark site. The numerical modelling was performed using the modelling tool MIKE SHE and is based on the site data and conceptual model of the Forsmark areas. This report presents solute transport applications based on both particle tracking simulations and advection-dispersion calculations. The MIKE SHE model is the basis for the transport modelling presented in this report. Simulation cases relevant for the transport from a deep geological repository have been studied, but also the pattern of near surface recharge and discharge areas. When the main part of the modelling work presented in this report was carried out, the flow modelling of the Forsmark site was not finalised. Thus, the focus of this work is to describe the sensitivity to different transport parameters, and not to point out specific areas as discharge areas from a future repository (this is to be done later, within the framework of the safety assessment). In the last chapter, however, results based on simulations with the re-calibrated MIKE SHE flow model are presented. The results from the MIKE SHE water movement calculations were used by cycling the calculated transient flow field for a selected one-year period as many times as needed to achieve the desired simulation period. The solute source was located either in the bedrock or on top of the model. In total, 15 different transport simulation cases were studied. Five of the simulations were particle tracking simulations, whereas the rest

  11. Hydrogeochemical evaluation for Simpevarp model version 1.2. Preliminary site description of the Simpevarp area

    Energy Technology Data Exchange (ETDEWEB)

    Laaksoharju, Marcus (ed.) [Geopoint AB, Stockholm (Sweden)

    2004-12-01

    process. It controls chloride concentration that, in turn, determines the re-equilibrium path (water-rock interaction) triggered by mixing. Coupled transport modelling was used to model the groundwater age, tritium content and calcite dissolution/precipitation processes at shallow groundwater depths at both Laxemar and Simpevarp. The modelled results provide additional support to hydrogeological models by using independent hydrochemical information and added support to the general hydrogeochemical understanding of the site. In this evaluation the groundwater model has been updated, the salinity distribution, mixing processes and the major reactions altering the groundwaters have been modelled down to a depth of 1000 m, and an updated Hydrogeochemical Site Descriptive Model version 1.2 has been produced. More groundwater and isotopic data, together with microbial information, colloids and gases, provided additional site descriptive information. Finally, the introduction of coupled modelling provided additional possibilities to address independently the various processes in question.

  12. Mechanical modelling of the Singoe deformation zone. Site descriptive modelling Forsmark stage 2.1

    Energy Technology Data Exchange (ETDEWEB)

    Glamheden, Rune; Maersk Hansen, Lars; Fredriksson, Anders; Bergkvist, Lars; Markstroem, Ingemar; Elfstroem, Mats [Golder Associates AB (Sweden)

    2007-02-15

    This project aims at demonstrating the theoretical approach developed by SKB for determination of mechanical properties of large deformation zones, in particular the Singoe deformation zone. Up to now, only bedrock and minor deformation zones have been characterized by means of this methodology, which has been modified for this project. The Singoe deformation zone is taken as a reference object to get a more comprehensive picture of the structure, which could be incorporated in a future version of the SDM of Forsmark. Furthermore, the Singoe Zone has been chosen because of available data from four tunnels. Scope of work has included compilation and analysis of geological information from site investigations and documentation of existing tunnels. Results have been analyzed and demonstrated by means of RVS-visualization. Numerical modelling has been used to obtain mechanical properties. Numerical modelling has also been carried out in order to verify the results by comparison of calculated and measured deformations. Compilation of various structures in the four tunnels coincides largely with a magnetic anomaly and also with the estimated width. Based on the study it is clear that the Singoe deformation zone has a heterogeneous nature. The number of fracture zones associated with the deformation zone varies on either side of the zone, as does the transition zone between host rock and the Singoe zone. The overall impression from the study is that the results demonstrate that the methodology used for simulating of equivalent mechanical properties is an applicable and adequate method, also in case of large deformation zones. Typical rock mechanical parameters of the Singoe deformations that can be used in the regional stress model considering the zone to be a single fracture are: 200 MPa/m in normal stiffness, 10-15 MPa/m in shear stiffness, 0.4 MPa in cohesion and 31.5 degrees in friction angle.

  13. Mechanical modelling of the Singoe deformation zone. Site descriptive modelling Forsmark stage 2.1

    International Nuclear Information System (INIS)

    Glamheden, Rune; Maersk Hansen, Lars; Fredriksson, Anders; Bergkvist, Lars; Markstroem, Ingemar; Elfstroem, Mats

    2007-02-01

    This project aims at demonstrating the theoretical approach developed by SKB for determination of mechanical properties of large deformation zones, in particular the Singoe deformation zone. Up to now, only bedrock and minor deformation zones have been characterized by means of this methodology, which has been modified for this project. The Singoe deformation zone is taken as a reference object to get a more comprehensive picture of the structure, which could be incorporated in a future version of the SDM of Forsmark. Furthermore, the Singoe Zone has been chosen because of available data from four tunnels. Scope of work has included compilation and analysis of geological information from site investigations and documentation of existing tunnels. Results have been analyzed and demonstrated by means of RVS-visualization. Numerical modelling has been used to obtain mechanical properties. Numerical modelling has also been carried out in order to verify the results by comparison of calculated and measured deformations. Compilation of various structures in the four tunnels coincides largely with a magnetic anomaly and also with the estimated width. Based on the study it is clear that the Singoe deformation zone has a heterogeneous nature. The number of fracture zones associated with the deformation zone varies on either side of the zone, as does the transition zone between host rock and the Singoe zone. The overall impression from the study is that the results demonstrate that the methodology used for simulating of equivalent mechanical properties is an applicable and adequate method, also in case of large deformation zones. Typical rock mechanical parameters of the Singoe deformations that can be used in the regional stress model considering the zone to be a single fracture are: 200 MPa/m in normal stiffness, 10-15 MPa/m in shear stiffness, 0.4 MPa in cohesion and 31.5 degrees in friction angle

  14. Thermal modelling. Preliminary site description Laxemar subarea - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Sundberg, Jan; Wrafter, John; Back, Paer-Erik; Laendell, Maerta [Geo Innova AB, Linkoeping (Sweden)

    2006-02-15

    This report presents the thermal site descriptive model for the Laxemar subarea, version 1.2. The main objective of this report is to present the thermal modelling work where data has been identified, quality controlled, evaluated and summarised in order to make an upscaling to lithological domain level possible. The thermal conductivity at canister scale has been modelled for five different lithological domains: RSMA (Aevroe granite), RSMBA (mixture of Aevroe granite and fine-grained dioritoid), RSMD (quartz monzodiorite), RSME (diorite/gabbro) and RSMM (mix domain with high frequency of diorite to gabbro). A base modelling approach has been used to determine the mean value of the thermal conductivity. Four alternative/complementary approaches have been used to evaluate the spatial variability of the thermal conductivity at domain level. The thermal modelling approaches are based on the lithological domain model for the Laxemar subarea, version 1.2 together with rock type models based on measured and calculated (from mineral composition) thermal conductivities. For one rock type, Aevroe granite (501044), density loggings have also been used in the domain modelling in order to evaluate the spatial variability within the Aevroe granite. This has been possible due to an established relationship between density and thermal conductivity, valid for the Aevroe granite. Results indicate that the means of thermal conductivity for the various domains are expected to exhibit a variation from 2.45 W/(m.K) to 2.87 W/(m.K). The standard deviation varies according to the scale considered, and for the 0.8 m scale it is expected to range from 0.17 to 0.29 W/(m.K). Estimates of lower tail percentiles for the same scale are presented for all five domains. The temperature dependence is rather small with a decrease in thermal conductivity of 1.1-5.3% per 100 deg C increase in temperature for the dominant rock types. There are a number of important uncertainties associated with these

  15. Regional hydrogeological simulations for Forsmark - numerical modelling using CONNECTFLOW. Preliminary site description Forsmark area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, Lee; Cox, Ian; Hunter, Fiona; Jackson, Peter; Joyce, Steve; Swift, Ben [Serco Assurance, Risley (United Kingdom); Gylling, Bjoern; Marsic, Niko [Kemakta Konsult AB, Stockholm (Sweden)

    2005-05-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) carries out site investigations in two different candidate areas in Sweden with the objective of describing the in-situ conditions for a bedrock repository for spent nuclear fuel. The site characterisation work is divided into two phases, an initial site investigation phase (IPLU) and a complete site investigation phase (KPLU). The results of IPLU are used as a basis for deciding on a subsequent KPLU phase. On the basis of the KPLU investigations a decision is made as to whether detailed characterisation will be performed (including sinking of a shaft). An integrated component in the site characterisation work is the development of site descriptive models. These comprise basic models in three dimensions with an accompanying text description. Central in the modelling work is the geological model, which provides the geometrical context in terms of a model of deformation zones and the rock mass between the zones. Using the geological and geometrical description models as a basis, descriptive models for other geo-disciplines (hydrogeology, hydro-geochemistry, rock mechanics, thermal properties and transport properties) will be developed. Great care is taken to arrive at a general consistency in the description of the various models and assessment of uncertainty and possible needs of alternative models. Here, a numerical model is developed on a regional-scale (hundreds of square kilometres) to understand the zone of influence for groundwater flow that affects the Forsmark area. Transport calculations are then performed by particle tracking from a local-scale release area (a few square kilometres) to identify potential discharge areas for the site and using greater grid resolution. The main objective of this study is to support the development of a preliminary Site Description of the Forsmark area on a regional-scale based on the available data of 30 June 2004 and the previous Site Description. A more specific

  16. Strategy for a Rock Mechanics Site Descriptive Model. Development and testing of the empirical approach

    International Nuclear Information System (INIS)

    Roeshoff, Kennert; Lanaro, Flavio; Lanru Jing

    2002-05-01

    This report presents the results of one part of a wide project for the determination of a methodology for the determination of the rock mechanics properties of the rock mass for the so-called Aespoe Test Case. The Project consists of three major parts: the empirical part dealing with the characterisation of the rock mass by applying empirical methods, a part determining the rock mechanics properties of the rock mass through numerical modelling, and a third part carrying out numerical modelling for the determination of the stress state at Aespoe. All Project's parts were performed based on a limited amount of data about the geology and mechanical tests on samples selected from the Aespoe Database. This Report only considers the empirical approach. The purpose of the project is the development of a descriptive rock mechanics model for SKBs rock mass investigations for a final repository site. The empirical characterisation of the rock mass provides correlations with some of the rock mechanics properties of the rock mass such as the deformation modulus, the friction angle and cohesion for a certain stress interval and the uniaxial compressive strength. For the characterisation of the rock mass, several empirical methods were analysed and reviewed. Among those methods, some were chosen because robust, applicable and widespread in modern rock mechanics. Major weight was given to the well-known Tunnel Quality Index (Q) and Rock Mass Rating (RMR) but also the Rock Mass Index (RMi), the Geological Strength Index (GSI) and Ramamurthy's Criterion were applied for comparison with the two classical methods. The process of: i) sorting the geometrical/geological/rock mechanics data, ii) identifying homogeneous rock volumes, iii) determining the input parameters for the empirical ratings for rock mass characterisation; iv) evaluating the mechanical properties by using empirical relations with the rock mass ratings; was considered. By comparing the methodologies involved by the

  17. Strategy for a Rock Mechanics Site Descriptive Model. Development and testing of the empirical approach

    Energy Technology Data Exchange (ETDEWEB)

    Roeshoff, Kennert; Lanaro, Flavio [Berg Bygg Konsult AB, Stockholm (Sweden); Lanru Jing [Royal Inst. of Techn., Stockholm (Sweden). Div. of Engineering Geology

    2002-05-01

    This report presents the results of one part of a wide project for the determination of a methodology for the determination of the rock mechanics properties of the rock mass for the so-called Aespoe Test Case. The Project consists of three major parts: the empirical part dealing with the characterisation of the rock mass by applying empirical methods, a part determining the rock mechanics properties of the rock mass through numerical modelling, and a third part carrying out numerical modelling for the determination of the stress state at Aespoe. All Project's parts were performed based on a limited amount of data about the geology and mechanical tests on samples selected from the Aespoe Database. This Report only considers the empirical approach. The purpose of the project is the development of a descriptive rock mechanics model for SKBs rock mass investigations for a final repository site. The empirical characterisation of the rock mass provides correlations with some of the rock mechanics properties of the rock mass such as the deformation modulus, the friction angle and cohesion for a certain stress interval and the uniaxial compressive strength. For the characterisation of the rock mass, several empirical methods were analysed and reviewed. Among those methods, some were chosen because robust, applicable and widespread in modern rock mechanics. Major weight was given to the well-known Tunnel Quality Index (Q) and Rock Mass Rating (RMR) but also the Rock Mass Index (RMi), the Geological Strength Index (GSI) and Ramamurthy's Criterion were applied for comparison with the two classical methods. The process of: i) sorting the geometrical/geological/rock mechanics data, ii) identifying homogeneous rock volumes, iii) determining the input parameters for the empirical ratings for rock mass characterisation; iv) evaluating the mechanical properties by using empirical relations with the rock mass ratings; was considered. By comparing the methodologies involved

  18. Regional hydrogeological simulations. Numerical modelling using ConnectFlow. Preliminary site description Simpevarp sub area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, Lee; Hoch, Andrew; Hunter, Fiona; Jackson, Peter [Serco Assurance, Risley (United Kingdom); Marsic, Niko [Kemakta Konsult, Stockholm (Sweden)

    2005-02-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) carries out site investigations in two different candidate areas in Sweden with the objective of describing the in situ conditions for a bedrock repository for spent nuclear fuel. The two candidate areas are named Forsmark and Simpevarp. The site characterisation work is divided into two phases, an initial site investigation phase (IPLU) and a complete site investigation phase (KPLU). The results of IPLU are used as a basis for deciding on a subsequent KPLU phase. On the basis of the KPLU investigations a decision is made as to whether detailed characterisation will be performed (including sinking of a shaft).An integrated component in the site characterisation work is the development of site descriptive models. These comprise basic models in three dimensions with an accompanying text description. Central in the modelling work is the geological model which provides the geometrical context in terms of a model of deformation zones and the rock mass between the zones. Using the geological and geometrical description models as a basis, descriptive models for other geo-disciplines (hydrogeology, hydro-geochemistry, rock mechanics, thermal properties and transport properties) will be developed. Great care is taken to arrive at a general consistency in the description of the various models and assessment of uncertainty and possible needs of alternative models.Here, a numerical model is developed on a regional-scale (hundreds of square kilometres) to understand the zone of influence for groundwater flow that effects the Simpevarp area. Transport calculations are then performed by particle tracking from a local-scale release area (tens of square kilometres) to identify potential discharge areas for the site. The transport from the two site-scale release areas (a few square kilometres) at the Simpevarp site and the Laxemar site are also considered more specifically and using greater grid resolution.The main

  19. Strategy for a numerical Rock Mechanics Site Descriptive Model. Further development of the theoretical/numerical approach

    International Nuclear Information System (INIS)

    Olofsson, Isabelle; Fredriksson, Anders

    2005-05-01

    The Swedish Nuclear and Fuel Management Company (SKB) is conducting Preliminary Site Investigations at two different locations in Sweden in order to study the possibility of a Deep Repository for spent fuel. In the frame of these Site Investigations, Site Descriptive Models are achieved. These products are the result of an interaction of several disciplines such as geology, hydrogeology, and meteorology. The Rock Mechanics Site Descriptive Model constitutes one of these models. Before the start of the Site Investigations a numerical method using Discrete Fracture Network (DFN) models and the 2D numerical software UDEC was developed. Numerical simulations were the tool chosen for applying the theoretical approach for characterising the mechanical rock mass properties. Some shortcomings were identified when developing the methodology. Their impacts on the modelling (in term of time and quality assurance of results) were estimated to be so important that the improvement of the methodology with another numerical tool was investigated. The theoretical approach is still based on DFN models but the numerical software used is 3DEC. The main assets of the programme compared to UDEC are an optimised algorithm for the generation of fractures in the model and for the assignment of mechanical fracture properties. Due to some numerical constraints the test conditions were set-up in order to simulate 2D plane strain tests. Numerical simulations were conducted on the same data set as used previously for the UDEC modelling in order to estimate and validate the results from the new methodology. A real 3D simulation was also conducted in order to assess the effect of the '2D' conditions in the 3DEC model. Based on the quality of the results it was decided to update the theoretical model and introduce the new methodology based on DFN models and 3DEC simulations for the establishment of the Rock Mechanics Site Descriptive Model. By separating the spatial variability into two parts, one

  20. Strategy for a Rock Mechanics Site Descriptive Model. Development and testing of an approach to modelling the state of stress

    Energy Technology Data Exchange (ETDEWEB)

    Hakami, Eva; Hakami, Hossein [Itasca Geomekanik AB, Solna (Sweden); Cosgrove, John [Imperial College of Science and Technology, London (United Kingdom)

    2002-05-01

    The overall objective of this project has been to develop, test and establish a method for creating a Rock Mechanics Site Descriptive Model for a site considered in the site investigation programme. The work was divided into three parts, the empirical and theoretical 'property models' and the 'stress model'. The work on the stress model is presented in this report. The work consisted of i) a literature review about geological factors controlling in situ stress and a review about the use of numerical models for this subject, ii) the development of recommendations on the methodology to be applied during a site investigation and iii) the Test Case exercise, where the suggested methods were tested. The main mechanism controlling the in situ stress magnitudes in Sweden is plate tectonics causing the stress field to show similarities in most parts of north-western Europe, having a NW-SE trend of the maximum principal stress. The orientation of the stress field is largely determined by the relative movements by the plates. However, the stress orientation may also be influenced by the presence of large regional weak zones, such as the Tornquist deformation zone that lies between Sweden and Denmark. The strike of the Tornquist deformation zone is parallel to the maximum principal stress as observed in central and southern Sweden. The magnitude of the stress is more difficult to estimate, but the general pattern is an increase in magnitude with depth, at least for the upper kilometres. To determine the stress magnitude at a certain site and depth, with reasonable certainty, stress measurement should be used. A methodology for building a stress model has been proposed. It involves different steps starting with a preliminary stress estimation, followed by steps for interpreting site-specific information. If the stress pattern and structural geology of the site are complex, including major fracture zones intersecting the area, numerical analyses of the

  1. Strategy for a Rock Mechanics Site Descriptive Model. Development and testing of an approach to modelling the state of stress

    International Nuclear Information System (INIS)

    Hakami, Eva; Hakami, Hossein; Cosgrove, John

    2002-05-01

    The overall objective of this project has been to develop, test and establish a method for creating a Rock Mechanics Site Descriptive Model for a site considered in the site investigation programme. The work was divided into three parts, the empirical and theoretical 'property models' and the 'stress model'. The work on the stress model is presented in this report. The work consisted of i) a literature review about geological factors controlling in situ stress and a review about the use of numerical models for this subject, ii) the development of recommendations on the methodology to be applied during a site investigation and iii) the Test Case exercise, where the suggested methods were tested. The main mechanism controlling the in situ stress magnitudes in Sweden is plate tectonics causing the stress field to show similarities in most parts of north-western Europe, having a NW-SE trend of the maximum principal stress. The orientation of the stress field is largely determined by the relative movements by the plates. However, the stress orientation may also be influenced by the presence of large regional weak zones, such as the Tornquist deformation zone that lies between Sweden and Denmark. The strike of the Tornquist deformation zone is parallel to the maximum principal stress as observed in central and southern Sweden. The magnitude of the stress is more difficult to estimate, but the general pattern is an increase in magnitude with depth, at least for the upper kilometres. To determine the stress magnitude at a certain site and depth, with reasonable certainty, stress measurement should be used. A methodology for building a stress model has been proposed. It involves different steps starting with a preliminary stress estimation, followed by steps for interpreting site-specific information. If the stress pattern and structural geology of the site are complex, including major fracture zones intersecting the area, numerical analyses of the stress field is

  2. Olkiluoto site description 2008. Part 1

    International Nuclear Information System (INIS)

    2009-04-01

    This third version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2006 (Andersson et al. 2007) with the data and knowledge obtained up to December 2007. The main product of the modelling has been to develop an updated version of the descriptive model of the site (the Site Descriptive Model), i.e. a model describing the geometry, properties of the bedrock and the water and the associated interacting processes and mechanisms. The Site Descriptive Model is divided into six parts: the surface system, geology, rock mechanics, hydrogeology, hydrogeochemistry and migration, which are presented in individual chapters. Five separated models are presented: the geological, rock mechanics, hydrogeological, hydrogeochemical and migration models. The main advances since Site Report 2006 are: (1) The geological model has been revised according to new data and interpretations. This has improved the consistency between the locations of the deformation zones in the geological model and the hydraulic zones in the hydrogeological model, (2) New 3D seismic data have been incorporated within the geological model and an initial model for the eastern part of the Island is presented. Site-scale brittle deformation zones are extrapolated to intersect the surrounding regional lineaments, unless prohibited by direct observations to the contrary. The alteration model has been revised, showing a clear correspondence between the illitisation and the sitescale fault zones, (3) A first account of the development of the brittle deformation history of the site is provided, (4) A new geological DFN model has been developed, that considers mapped fracture traces from both the surface and the ONKALO, (5) A new stress state model and fracture and fracture zone properties are presented, (6) A new hydrogeological DFN model has been developed, (7) An updated site scale (EPM) flow model has been developed, (8) There has been an

  3. Strategy for a Rock Mechanics Site Descriptive Model. A test case based on data from the Aespoe HRL

    International Nuclear Information System (INIS)

    Hudson, John A

    2002-06-01

    In anticipation of the SKB Site Investigations for radioactive waste disposal, an approach has been developed for the Rock Mechanics Site Descriptive Model. This approach was tested by predicting the rock mechanics properties of a 600 m x 180 m x 120 m rock volume at the Aespoe Hard Rock Laboratory (HRL) using limited borehole data of the type typically obtained during a site investigation. These predicted properties were then compared with 'best estimate' properties obtained from a study of the test rock volume using additional information, mainly tunnel data. The exercise was known as the Test Case, and is the subject of this Report. Three modelling techniques were used to predict the rock properties: the 'empirical approach' - the rock properties were estimated using rock mass classification schemes and empirical correlation formulae; the 'theoretical approach' - the rock properties were estimated using numerical modelling techniques; and the 'stress approach' - the rock stress state was estimated using primary data and numerical modelling. These approaches are described separately and respectively. Following an explanation of the context for the Test Case within the strategy for developing the Rock Mechanics Site Descriptive Model, conditions at the Aespoe HRL are described in Chapter 2. The Test Case organization and the suite of nine Protocols used to ensure that the work was appropriately guided and co-ordinated are described in Chapter 3. The methods for predicting the rock properties and the rock stress, and comparisons with the 'best estimate' properties of the actual conditions, are presented in Chapters 4 and 5. Finally, the conclusions from this Test Case exercise are given in Chapter 6. General recommendations for the management of this type of Test Case are also included

  4. Strategy for a Rock Mechanics Site Descriptive Model. A test case based on data from the Aespoe HRL

    Energy Technology Data Exchange (ETDEWEB)

    Hudson, John A (ed.) [Rock Engineering Consultants, Welwyn Garden City (United Kingdom)

    2002-06-01

    In anticipation of the SKB Site Investigations for radioactive waste disposal, an approach has been developed for the Rock Mechanics Site Descriptive Model. This approach was tested by predicting the rock mechanics properties of a 600 m x 180 m x 120 m rock volume at the Aespoe Hard Rock Laboratory (HRL) using limited borehole data of the type typically obtained during a site investigation. These predicted properties were then compared with 'best estimate' properties obtained from a study of the test rock volume using additional information, mainly tunnel data. The exercise was known as the Test Case, and is the subject of this Report. Three modelling techniques were used to predict the rock properties: the 'empirical approach' - the rock properties were estimated using rock mass classification schemes and empirical correlation formulae; the 'theoretical approach' - the rock properties were estimated using numerical modelling techniques; and the 'stress approach' - the rock stress state was estimated using primary data and numerical modelling. These approaches are described separately and respectively. Following an explanation of the context for the Test Case within the strategy for developing the Rock Mechanics Site Descriptive Model, conditions at the Aespoe HRL are described in Chapter 2. The Test Case organization and the suite of nine Protocols used to ensure that the work was appropriately guided and co-ordinated are described in Chapter 3. The methods for predicting the rock properties and the rock stress, and comparisons with the 'best estimate' properties of the actual conditions, are presented in Chapters 4 and 5. Finally, the conclusions from this Test Case exercise are given in Chapter 6. General recommendations for the management of this type of Test Case are also included.

  5. Statistical model of fractures and deformation zones. Preliminary site description, Laxemar subarea, version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Hermanson, Jan; Forssberg, Ola [Golder Associates AB, Stockholm (Sweden); Fox, Aaron; La Pointe, Paul [Golder Associates Inc., Redmond, WA (United States)

    2005-10-15

    The goal of this summary report is to document the data sources, software tools, experimental methods, assumptions, and model parameters in the discrete-fracture network (DFN) model for the local model volume in Laxemar, version 1.2. The model parameters presented herein are intended for use by other project modeling teams. Individual modeling teams may elect to simplify or use only a portion of the DFN model, depending on their needs. This model is not intended to be a flow model or a mechanical model; as such, only the geometrical characterization is presented. The derivations of the hydraulic or mechanical properties of the fractures or their subsurface connectivities are not within the scope of this report. This model represents analyses carried out on particular data sets. If additional data are obtained, or values for existing data are changed or excluded, the conclusions reached in this report, and the parameter values calculated, may change as well. The model volume is divided into two subareas; one located on the Simpevarp peninsula adjacent to the power plant (Simpevarp), and one further to the west (Laxemar). The DFN parameters described in this report were determined by analysis of data collected within the local model volume. As such, the final DFN model is only valid within this local model volume and the modeling subareas (Laxemar and Simpevarp) within.

  6. Implementation of Malaria Dynamic Models in Municipality Level Early Warning Systems in Colombia. Part I: Description of Study Sites

    Science.gov (United States)

    Ruiz, Daniel; Cerón, Viviana; Molina, Adriana M.; Quiñónes, Martha L.; Jiménez, Mónica M.; Ahumada, Martha; Gutiérrez, Patricia; Osorio, Salua; Mantilla, Gilma; Connor, Stephen J.; Thomson, Madeleine C.

    2014-01-01

    As part of the Integrated National Adaptation Pilot project and the Integrated Surveillance and Control System, the Colombian National Institute of Health is working on the design and implementation of a Malaria Early Warning System framework, supported by seasonal climate forecasting capabilities, weather and environmental monitoring, and malaria statistical and dynamic models. In this report, we provide an overview of the local ecoepidemiologic settings where four malaria process-based mathematical models are currently being implemented at a municipal level. The description includes general characteristics, malaria situation (predominant type of infection, malaria-positive cases data, malaria incidence, and seasonality), entomologic conditions (primary and secondary vectors, mosquito densities, and feeding frequencies), climatic conditions (climatology and long-term trends), key drivers of epidemic outbreaks, and non-climatic factors (populations at risk, control campaigns, and socioeconomic conditions). Selected pilot sites exhibit different ecoepidemiologic settings that must be taken into account in the development of the integrated surveillance and control system. PMID:24891460

  7. Updated strategy and test of new concepts for groundwater flow modelling in Forsmark in preparation of site descriptive modelling stage 2.2

    Energy Technology Data Exchange (ETDEWEB)

    Follin, Sven [SF GeoLogic AB (Sweden); Johansson, Per-Olof [Artesia Grundvattenkonsult AB (Sweden); Leven, Jakob [Geosigma AB (Sweden); Hartley, Lee; Holton, David; McCarthy, Rachel; Roberts, David [Serco Assurance (United Kingdom)

    2007-01-15

    As part of the preliminary Site Descriptive Modelling (SDM version 1.2) for the Initial Site Investigation (ISI) stage at Forsmark, Simpevarp and Laxemar, a methodology was developed for constructing hydrogeological models of the crystalline bedrock. The methodology achieved reasonable success given the restricted amounts and types of data available at the time. Notwithstanding, several issues of concern have surfaced following the reviews of the preliminary site descriptions of the three sites. Possible solutions to parts of the problems have been discussed internally for a longer time and an integrated view and strategy forward has been formulated. The 'new strategy' is not a complete shift in methodology, however, but a refocusing on and clarification of the key aspects that the hydrogeological SDM needs to accomplish. In broad terms the basic principle of the 'new strategy' suggested is to develop an overall conceptual model that first establishes the major flowing deformation zones, and then gradually approaches determination of the hydraulic properties of the bedrock outside these zones in the potential repository volume. On each scale, the focus of the description should be on features/structures of significance on that scale. Clearly, a detailed (although statistical) description of the repository and canister deposition hole scale is the end goal, but this approach (which also is more the traditional approach in hydrogeology) is judged to provide a much better motivated overall geometrical description. Furthermore, the 'new strategy' puts more emphasis on field testing (e.g. interference tests) and data analyses and less on numerical simulation and calibration. That is, before extensive (and costly) simulations and model calibrations are made it needs to be clearly understood what could be the potential gains of carrying them out. This report presents the conceptual model development for Forsmark in preparation of the site

  8. Verification study on technology for site investigation for geological disposal. Confirmation of the applicability of survey methods through establishing site descriptive models in accordance with stepwise investigation approach

    International Nuclear Information System (INIS)

    Kondo, Hirofumi; Suzuki, Koichi; Hasegawa, Takuma; Hamada, Takaomi; Yoshimura, Kimitaka

    2014-01-01

    The Yokosuka Demonstration and Validation Project, which uses the Yokosuka Central Research Institute of Electric Power Industry (CRIEPI) site, a Neogene sedimentary and coastal environment, has been conducted since the 2006 fiscal year as a cooperative research project between NUMO (Nuclear Waste Management Organization of Japan) and CRIEPI. The objectives of this project were to examine and refine the basic methodology of the investigation and assessment in accordance with the conditions of geological environment at each stage of investigations from the surface (Preliminary Investigation and the first half of Detailed Investigation conducted by NUMO) for high level radioactive waste geological disposal. Within investigation technologies at these early stages, a borehole survey is an important means of directly obtaining various properties of the deep geological environment. On the other hand, surface geophysical prospecting data provide information about the geological and resistivity structures at depth for planning borehole surveys. During the 2006-2009 fiscal years, a series of on-site surveys and tests, including borehole surveys of YDP-1 (depth: 350 m) and YDP-2 (depth: 500 m), were conducted in this test site. Furthermore, seismic surveys (including seismic reflection method) and electromagnetic surveys (including magnetotelluric method) were conducted within the expanded CRIEPI site in the 2010 fiscal year to obtain information about the geological structure, and the resistivity structure reflecting the distribution of the salt water/fresh water boundary, respectively, to a depth of over several hundred meters. The validity of existing survey and testing methods for stepwise investigations (from surface to borehole surveys) for obtaining properties of the geological environment (in various conditions relating to differences in the properties of the Miura and the Hayama Groups at this site) was confirmed through establishing site descriptive models based on

  9. CRAC2 model description

    International Nuclear Information System (INIS)

    Ritchie, L.T.; Alpert, D.J.; Burke, R.P.; Johnson, J.D.; Ostmeyer, R.M.; Aldrich, D.C.; Blond, R.M.

    1984-03-01

    The CRAC2 computer code is a revised version of CRAC (Calculation of Reactor Accident Consequences) which was developed for the Reactor Safety Study. This document provides an overview of the CRAC2 code and a description of each of the models used. Significant improvements incorporated into CRAC2 include an improved weather sequence sampling technique, a new evacuation model, and new output capabilities. In addition, refinements have been made to the atmospheric transport and deposition model. Details of the modeling differences between CRAC2 and CRAC are emphasized in the model descriptions

  10. Regional hydrogeological simulations for Forsmark - numerical modelling using DarcyTools. Preliminary site description Forsmark area version 1.2

    International Nuclear Information System (INIS)

    Follin, Sven; Stigsson, Martin; Svensson, Urban

    2005-12-01

    A numerical model is developed on a regional-scale (hundreds of square kilometres) to study the zone of influence for variable-density groundwater flow that affects the Forsmark area. Transport calculations are performed by particle tracking from a local-scale release area (a few square kilometres) to test the sensitivity to different hydrogeological uncertainties and the need for far-field realism. The main objectives of the regional flow modelling were to achieve the following: I. Palaeo-hydrogeological understanding: An improved understanding of the palaeohydrogeological conditions is necessary in order to gain credibility for the site descriptive model in general and the hydrogeological description in particular. This requires modelling of the groundwater flow from the last glaciation up to present-day with comparisons against measured TDS and other hydro-geochemical measures. II. Simulation of flow paths: The simulation and visualisation of flow paths from a tentative repository area is a means for describing the role of the current understanding of the modelled hydrogeological conditions in the target volume, i.e. the conditions of primary interest for Safety Assessment. Of particular interest here is demonstration of the need for detailed far-field realism in the numerical simulations. The motivation for a particular model size (and resolution) and set of boundary conditions for a realistic description of the recharge and discharge connected to the flow at repository depth is an essential part of the groundwater flow path simulations. The numerical modelling was performed by two separate modelling teams, the ConnectFlow Team and the DarcyTools Team. The work presented in this report was based on the computer code DarcyTools developed by Computer-aided Fluid Engineering. DarcyTools is a kind of equivalent porous media (EPM) flow code specifically designed to treat flow and salt transport in sparsely fractured crystalline rock intersected by transmissive

  11. Regional hydrogeological simulations for Forsmark - numerical modelling using DarcyTools. Preliminary site description Forsmark area version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-12-15

    A numerical model is developed on a regional-scale (hundreds of square kilometres) to study the zone of influence for variable-density groundwater flow that affects the Forsmark area. Transport calculations are performed by particle tracking from a local-scale release area (a few square kilometres) to test the sensitivity to different hydrogeological uncertainties and the need for far-field realism. The main objectives of the regional flow modelling were to achieve the following: I. Palaeo-hydrogeological understanding: An improved understanding of the palaeohydrogeological conditions is necessary in order to gain credibility for the site descriptive model in general and the hydrogeological description in particular. This requires modelling of the groundwater flow from the last glaciation up to present-day with comparisons against measured TDS and other hydro-geochemical measures. II. Simulation of flow paths: The simulation and visualisation of flow paths from a tentative repository area is a means for describing the role of the current understanding of the modelled hydrogeological conditions in the target volume, i.e. the conditions of primary interest for Safety Assessment. Of particular interest here is demonstration of the need for detailed far-field realism in the numerical simulations. The motivation for a particular model size (and resolution) and set of boundary conditions for a realistic description of the recharge and discharge connected to the flow at repository depth is an essential part of the groundwater flow path simulations. The numerical modelling was performed by two separate modelling teams, the ConnectFlow Team and the DarcyTools Team. The work presented in this report was based on the computer code DarcyTools developed by Computer-aided Fluid Engineering. DarcyTools is a kind of equivalent porous media (EPM) flow code specifically designed to treat flow and salt transport in sparsely fractured crystalline rock intersected by transmissive

  12. Description of surface systems. Preliminary site description. Forsmark area Version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Lindborg, Tobias [ed.

    2005-06-01

    Swedish Nuclear Fuel and Waste Management Co (SKB) started site investigations for a deep repository for spent nuclear fuel in 2002 at two different sites in Sweden, Forsmark and Oskarshamn. The investigations should provide necessary information for a license application aimed at starting underground exploration. For this reason, ecosystem data need to be interpreted and assessed into site descriptive models, which in turn are used for safety assessment studies and for environmental impact assessment. Descriptions of the surface system are also needed for further planning of the site investigations. This report describes the surface ecosystems of the Forsmark site (e.g. hydrology, Quaternary deposits, chemistry, vegetation, animals and the human land use). The ecosystem description is an integration of the site and its regional setting, covering the current state of the biosphere as well as the ongoing natural processes affecting the longterm development. Improving the descriptions is important during both the initial and the complete site investigation phase. Before starting of the initial phase in Forsmark, version 0 of the site descriptive model was developed. The results of the initial site investigation phase is compiled into a preliminary site description of Forsmark (version 1.2) in June 2005. This report provides the major input and background to the biosphere description, in the 1.2 version of the Forsmark site description. The basis for this interim version is quality-assured field data from the Forsmark sub area and regional area, available in the SKB SICADA, and GIS data bases as of July 31th 2004 as well as version 1.1 of the Site Descriptive Model. To achieve an ecosystem site description there is a need to develop discipline-specific models by interpreting and analysing primary data. The different discipline-specific models are then integrated into a system describing interactions and flows and stocks of matter between and within functional units in

  13. Description of surface systems. Preliminary site description. Forsmark area Version 1.2

    International Nuclear Information System (INIS)

    Lindborg, Tobias

    2005-06-01

    Swedish Nuclear Fuel and Waste Management Co (SKB) started site investigations for a deep repository for spent nuclear fuel in 2002 at two different sites in Sweden, Forsmark and Oskarshamn. The investigations should provide necessary information for a license application aimed at starting underground exploration. For this reason, ecosystem data need to be interpreted and assessed into site descriptive models, which in turn are used for safety assessment studies and for environmental impact assessment. Descriptions of the surface system are also needed for further planning of the site investigations. This report describes the surface ecosystems of the Forsmark site (e.g. hydrology, Quaternary deposits, chemistry, vegetation, animals and the human land use). The ecosystem description is an integration of the site and its regional setting, covering the current state of the biosphere as well as the ongoing natural processes affecting the longterm development. Improving the descriptions is important during both the initial and the complete site investigation phase. Before starting of the initial phase in Forsmark, version 0 of the site descriptive model was developed. The results of the initial site investigation phase is compiled into a preliminary site description of Forsmark (version 1.2) in June 2005. This report provides the major input and background to the biosphere description, in the 1.2 version of the Forsmark site description. The basis for this interim version is quality-assured field data from the Forsmark sub area and regional area, available in the SKB SICADA, and GIS data bases as of July 31th 2004 as well as version 1.1 of the Site Descriptive Model. To achieve an ecosystem site description there is a need to develop discipline-specific models by interpreting and analysing primary data. The different discipline-specific models are then integrated into a system describing interactions and flows and stocks of matter between and within functional units in

  14. Description of the two-loop RELAP5 model of the L-Reactor at the Savannah River Site

    International Nuclear Information System (INIS)

    Cozzuol, J.M.; Davis, C.B.

    1989-12-01

    A two-loop RELAP5 input model of the L-Reactor at the Savannah River Site (SRS) was developed to support thermal-hydraulic analysis of SRS reactors. The model was developed to economically evaluate potential design changes. The primary simplifications in the model were in the number of loops and the detail in the moderator tank. The six loops in the reactor were modeled with two loops, one representing a single loop and the other representing five combined loops. The model has undergone a quality assurance review. This report describes the two-loop model, its limitations, and quality assurance. 29 refs., 18 figs., 10 tabs

  15. Compilation of data used for the analysis of the geological and hydrogeological DFN models. Site descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Hermanson, Jan; Fox, Aaron; Oehman, Johan; Rhen, Ingvar

    2008-08-01

    This report provides an overview and compilation of the various data that constitutes the basis for construction of the geological and hydrogeological discrete feature network (DFN) models as part of model version SDM-Site Laxemar. This includes a review of fracture data in boreholes and in outcrop. Furthermore, the basis for the construction of lineament maps is given as well as a review of the hydraulic test data from cored and percussion-drilled boreholes. An emphasis is put on graphical representation of borehole logs in the form of composites of geological, hydrogeological and even hydrogeochemical data in the case of cored boreholes. One major contribution is a compilation of characteristics of minor local deformation zones (MDZs) identified in cored boreholes. Basic orientation data and fracture intensity data are presented as a function of depth for individual boreholes. The coupling between hydrogeological data and geological data is further refined in plots of Posiva flow log (PFL) data vs. geological single hole interpretation data

  16. Improving the effectiveness of ecological site descriptions: General state-and-transition models and the Ecosystem Dynamics Interpretive Tool (EDIT)

    Science.gov (United States)

    Bestelmeyer, Brandon T.; Williamson, Jeb C.; Talbot, Curtis J.; Cates, Greg W.; Duniway, Michael C.; Brown, Joel R.

    2016-01-01

    State-and-transition models (STMs) are useful tools for management, but they can be difficult to use and have limited content.STMs created for groups of related ecological sites could simplify and improve their utility. The amount of information linked to models can be increased using tables that communicate management interpretations and important within-group variability.We created a new web-based information system (the Ecosystem Dynamics Interpretive Tool) to house STMs, associated tabular information, and other ecological site data and descriptors.Fewer, more informative, better organized, and easily accessible STMs should increase the accessibility of science information.

  17. Site descriptive modelling Forsmark, stage 2.2. A fracture domain concept as a basis for the statistical modelling of fractures and minor deformation zones, and interdisciplinary coordination

    Energy Technology Data Exchange (ETDEWEB)

    Olofsson, Isabelle; Simeonov, Assen [Swedish Nuclear Fuel and Waste Manageme nt Co., Stockholm (Sweden); Stephens, Michael [Geological Survey of Sweden (SGU), U ppsala (Sweden); Follin, Sven [SF GeoLogic AB, Taeby (Sweden); Nilsson, Ann-Chatrin [G eosigma AB, Uppsala (Sweden); Roeshoff, Kennert; Lindberg, Ulrika; Lanaro, Flavio [Bergbygg konsult AB, Haesselby (Sweden); Fredriksson, Anders; Persson, Lars [Golder Associat es AB (Sweden)

    2007-04-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterization at two different locations, Forsmark and Simpevarp/Laxemar, with the objective of siting a final waste repository at depth for spent nuclear fuel. The programme is built upon the development of site descriptive models after each data freeze. This report describes the first attempt to define fracture domains for the Forsmark site modelling in stage 2.2. Already during model version 1.2 at Forsmark, significant spatial variability in the fracture pattern was observed. The variability appeared to be so significant that it provoked the need for a subdivision of the model volume for the treatment of geological and hydrogeological data into sub-volumes. Subsequent analyses of data collected up to data freeze 2.1 led to a better understanding of the site and a concept for the definition of fracture domains based on geological characteristics matured. The main objectives of this report are to identify and describe fracture domains at the site on the basis of geological data and to compile hydrogeological, hydrogeochemical and rock mechanics data within each fracture domain and address the implications of this integration activity. On the basis of borehole data, six fracture domains (FFM01-FFM06) have been recognized inside and immediately around the candidate volume. Three of these domains (FFM01, FFM02 and FFM06) lie inside the target volume for a potential repository in the northwestern part of the candidate area, and need to be addressed in the geological DFN modelling work. The hydrogeological data support the subdivision of the bedrock into fracture domains FFM01, FFM02 and FFM03. Few or no data are available for the other three domains. The hydrogeochemical data also support the subdivision into fracture domains FFM01 and FFM02. Since few data are available from the bedrock between deformation zones inside FFM03, there is little information on the hydrogeochemical

  18. Site description of Laxemar at completion of the site investigation phase. SDM-Site Laxemar

    International Nuclear Information System (INIS)

    2009-12-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken site characterisation in two different areas, Forsmark and Laxemar-Simpevarp, in order to identify a suitable location for a geological repository of spent nuclear fuel according to the KBS-3 method. The site investigations have been conducted in campaigns, punctuated by data freezes. After each data freeze, the site data have been analysed and modelling has been carried out with the overall purpose to develop a site descriptive model (SDM). The site descriptive model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It is also essential for safety assessment, since the SDM is the only source for site-specific input. Another important use of the site descriptive model is in the environmental impact assessment. An SDM is an integrated model of geology, thermal properties, rock mechanics, hydrogeology, hydrogeochemistry, bedrock transport properties and a description of the surface system. The site descriptive model compiled in the current report, SDM-Site Laxemar, presents an integrated understanding of the Laxemar-Simpevarp area (with special emphasis on the Laxemar subarea) at the completion of the surface-based investigations, which were conducted during the period 2002 to 2007. A summary is also provided of the abundant underlying data and the discipline specific models that support the site understanding. The description relies heavily on background reports that address, in particular, details of the data analyses and modelling of the different disciplines. The Laxemar-Simpevarp area is located in the province of Smaaland within the municipality of Oskarshamn, about 230 km south of Stockholm. The candidate area for site investigation is located along the shoreline of the strait of Kalmarsund, within a 1.8 billion year old suite of well preserved bedrock belonging to the Transscandinavian Igneous Belt formed during

  19. Site description of Laxemar at completion of the site investigation phase. SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    2009-12-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken site characterisation in two different areas, Forsmark and Laxemar-Simpevarp, in order to identify a suitable location for a geological repository of spent nuclear fuel according to the KBS-3 method. The site investigations have been conducted in campaigns, punctuated by data freezes. After each data freeze, the site data have been analysed and modelling has been carried out with the overall purpose to develop a site descriptive model (SDM). The site descriptive model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It is also essential for safety assessment, since the SDM is the only source for site-specific input. Another important use of the site descriptive model is in the environmental impact assessment. An SDM is an integrated model of geology, thermal properties, rock mechanics, hydrogeology, hydrogeochemistry, bedrock transport properties and a description of the surface system. The site descriptive model compiled in the current report, SDM-Site Laxemar, presents an integrated understanding of the Laxemar-Simpevarp area (with special emphasis on the Laxemar subarea) at the completion of the surface-based investigations, which were conducted during the period 2002 to 2007. A summary is also provided of the abundant underlying data and the discipline specific models that support the site understanding. The description relies heavily on background reports that address, in particular, details of the data analyses and modelling of the different disciplines. The Laxemar-Simpevarp area is located in the province of Smaaland within the municipality of Oskarshamn, about 230 km south of Stockholm. The candidate area for site investigation is located along the shoreline of the strait of Kalmarsund, within a 1.8 billion year old suite of well preserved bedrock belonging to the Transscandinavian Igneous Belt formed during

  20. Site description of Forsmark at completion of the site investigation phase. SDM-Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    2008-12-15

    The Swedish Nuclear Fuel and Waste Management Co., SKB, has undertaken site characterisation in two different areas, Forsmark and Laxemar-Simpevarp, in order to identify a suitable location for a geological repository of spent nuclear fuel according to the KBS-3 method. The site investigations have been conducted in campaigns, punctuated by data freezes. After each data freeze, the site data have been analysed and modelling has been carried out with the overall purpose to develop a site descriptive model (SDM). The site descriptive model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It is also essential for safety assessment, since the model is the only source for site-specific input. Another important use of the site descriptive model is in the environmental impact assessment. An SDM is an integrated model for geology, thermal properties, rock mechanics, hydrogeology, hydrogeochemistry, bedrock transport properties and a description of the surface system. The site descriptive model compiled in the current report, SDM-Site, presents an integrated understanding of the Forsmark area at the completion of the surface-based investigations, which were conducted at Forsmark during the period 2002 to 2007. It also provides a summary of the abundant underlying data and the discipline-specific models that support the site understanding. The description relies heavily on background reports that address, in particular, details in data analyses and modelling in the different disciplines. The Forsmark area is located in northern Uppland within the municipality of Oesthammar, about 120 km north of Stockholm. The candidate area for site investigation is located along the shoreline of Oeregrundsgrepen, within the north-western part of a major tectonic lens that formed between 1.87 and 1.85 billion years ago during the Svecokarelian orogeny. The candidate area is approximately 6 km long and 2 km wide. The

  1. Site description of Forsmark at completion of the site investigation phase. SDM-Site Forsmark

    International Nuclear Information System (INIS)

    2008-12-01

    The Swedish Nuclear Fuel and Waste Management Co., SKB, has undertaken site characterisation in two different areas, Forsmark and Laxemar-Simpevarp, in order to identify a suitable location for a geological repository of spent nuclear fuel according to the KBS-3 method. The site investigations have been conducted in campaigns, punctuated by data freezes. After each data freeze, the site data have been analysed and modelling has been carried out with the overall purpose to develop a site descriptive model (SDM). The site descriptive model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It is also essential for safety assessment, since the model is the only source for site-specific input. Another important use of the site descriptive model is in the environmental impact assessment. An SDM is an integrated model for geology, thermal properties, rock mechanics, hydrogeology, hydrogeochemistry, bedrock transport properties and a description of the surface system. The site descriptive model compiled in the current report, SDM-Site, presents an integrated understanding of the Forsmark area at the completion of the surface-based investigations, which were conducted at Forsmark during the period 2002 to 2007. It also provides a summary of the abundant underlying data and the discipline-specific models that support the site understanding. The description relies heavily on background reports that address, in particular, details in data analyses and modelling in the different disciplines. The Forsmark area is located in northern Uppland within the municipality of Oesthammar, about 120 km north of Stockholm. The candidate area for site investigation is located along the shoreline of Oeregrundsgrepen, within the north-western part of a major tectonic lens that formed between 1.87 and 1.85 billion years ago during the Svecokarelian orogeny. The candidate area is approximately 6 km long and 2 km wide. The

  2. Preliminary site description Forsmark area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Skagius, Kristina [ed.

    2005-06-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterisation at two different locations, the Forsmark and Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. An integrated component in the characterisation work is the development of a site descriptive model that constitutes a description of the site and its regional setting, covering the current state of the geosphere and the biosphere as well as those ongoing natural processes that affect their long-term evolution. The present report documents the site descriptive modelling activities (version 1.2) for the Forsmark area. The overall objectives of the version 1.2 site descriptive modelling are to produce and document an integrated description of the site and its regional environments based on the site-specific data available from the initial site investigations and to give recommendations on continued investigations. The modelling work is based on primary data, i.e. quality-assured, geoscientific and ecological field data available in the SKB databases SICADA and GIS, available July 31, 2004. The work has been conducted by a project group and associated discipline-specific working groups. The members of the project group represent the disciplines of geology, rock mechanics, thermal properties, hydrogeology, hydrogeochemistry, transport properties and surface ecosystems (including overburden, surface hydrogeochemistry and hydrology). In addition, some group members have specific qualifications of importance in this type of project e.g. expertise in RVS (Rock Visualisation System) modelling, GIS-modelling and in statistical data analysis. The overall strategy to achieve a site description is to develop discipline-specific models by interpretation and analyses of the primary data. The different discipline-specific models are then integrated into a site description. Methodologies for developing the discipline-specific models are documented in

  3. Preliminary site description Forsmark area - version 1.2

    International Nuclear Information System (INIS)

    Skagius, Kristina

    2005-06-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is undertaking site characterisation at two different locations, the Forsmark and Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. An integrated component in the characterisation work is the development of a site descriptive model that constitutes a description of the site and its regional setting, covering the current state of the geosphere and the biosphere as well as those ongoing natural processes that affect their long-term evolution. The present report documents the site descriptive modelling activities (version 1.2) for the Forsmark area. The overall objectives of the version 1.2 site descriptive modelling are to produce and document an integrated description of the site and its regional environments based on the site-specific data available from the initial site investigations and to give recommendations on continued investigations. The modelling work is based on primary data, i.e. quality-assured, geoscientific and ecological field data available in the SKB databases SICADA and GIS, available July 31, 2004. The work has been conducted by a project group and associated discipline-specific working groups. The members of the project group represent the disciplines of geology, rock mechanics, thermal properties, hydrogeology, hydrogeochemistry, transport properties and surface ecosystems (including overburden, surface hydrogeochemistry and hydrology). In addition, some group members have specific qualifications of importance in this type of project e.g. expertise in RVS (Rock Visualisation System) modelling, GIS-modelling and in statistical data analysis. The overall strategy to achieve a site description is to develop discipline-specific models by interpretation and analyses of the primary data. The different discipline-specific models are then integrated into a site description. Methodologies for developing the discipline-specific models are documented in

  4. Open challenges in structure-based virtual screening: Receptor modeling, target flexibility consideration and active site water molecules description.

    Science.gov (United States)

    Spyrakis, Francesca; Cavasotto, Claudio N

    2015-10-01

    Structure-based virtual screening is currently an established tool in drug lead discovery projects. Although in the last years the field saw an impressive progress in terms of algorithm development, computational performance, and retrospective and prospective applications in ligand identification, there are still long-standing challenges where further improvement is needed. In this review, we consider the conceptual frame, state-of-the-art and recent developments of three critical "structural" issues in structure-based drug lead discovery: the use of homology modeling to accurately model the binding site when no experimental structures are available, the necessity of accounting for the dynamics of intrinsically flexible systems as proteins, and the importance of considering active site water molecules in lead identification and optimization campaigns. Copyright © 2015 Elsevier Inc. All rights reserved.

  5. Description of surface systems. Preliminary site description Simpevarp sub area - Version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Lindborg, Tobias [ed.

    2005-03-01

    Swedish Nuclear Fuel and Waste Management Co is currently conducting site characterisation in the Simpevarp area. The area is divided into two subareas, the Simpevarp and the Laxemar subarea. The two subareas are surrounded by a common regional model area, the Simpevarp area. This report describes both the regional area and the subareas. This report is an interim version (model version 1.2) of the description of the surface systems at the Simpevarp area, and should be seen as a background report to the site description of the Simpevarp area, version 1.2, SKB-R--05-08. The basis for this description is quality-assured field data available in the SKB SICADA and GIS databases, together with generic data from the literature. The Surface system, here defined as everything above the bedrock, comprises a number of separate disciplines (e.g. hydrology, geology, topography, oceanography and ecology). Each discipline has developed descriptions and models for a number of properties that together represent the site description. The current methodology for developing the surface system description and the integration to ecosystem models is documented in a methodology strategy report SKB-R--03-06. The procedures and guidelines given in that report were followed in this report. Compared with version 1.1 of the surface system description SKB-R--04-25, this report presents considerable additional features, especially in the ecosystem description (Chapter 4) and in the description of the surface hydrology (Section 3.4). A first attempt has also been made to connect the flow of matter (carbon) between the different ecosystems into an overall ecosystem model at a landscape level. A summarised version of this report is also presented in SKB-R--05-08 together with geological-, hydrogeological-, transport properties-, thermal properties-, rock mechanics- and hydrogeochemical descriptions.

  6. Description of surface systems. Preliminary site description Simpevarp sub area - Version 1.2

    International Nuclear Information System (INIS)

    Lindborg, Tobias

    2005-03-01

    Swedish Nuclear Fuel and Waste Management Co is currently conducting site characterisation in the Simpevarp area. The area is divided into two subareas, the Simpevarp and the Laxemar subarea. The two subareas are surrounded by a common regional model area, the Simpevarp area. This report describes both the regional area and the subareas. This report is an interim version (model version 1.2) of the description of the surface systems at the Simpevarp area, and should be seen as a background report to the site description of the Simpevarp area, version 1.2, SKB-R--05-08. The basis for this description is quality-assured field data available in the SKB SICADA and GIS databases, together with generic data from the literature. The Surface system, here defined as everything above the bedrock, comprises a number of separate disciplines (e.g. hydrology, geology, topography, oceanography and ecology). Each discipline has developed descriptions and models for a number of properties that together represent the site description. The current methodology for developing the surface system description and the integration to ecosystem models is documented in a methodology strategy report SKB-R--03-06. The procedures and guidelines given in that report were followed in this report. Compared with version 1.1 of the surface system description SKB-R--04-25, this report presents considerable additional features, especially in the ecosystem description (Chapter 4) and in the description of the surface hydrology (Section 3.4). A first attempt has also been made to connect the flow of matter (carbon) between the different ecosystems into an overall ecosystem model at a landscape level. A summarised version of this report is also presented in SKB-R--05-08 together with geological-, hydrogeological-, transport properties-, thermal properties-, rock mechanics- and hydrogeochemical descriptions

  7. Nevada Test Site Environmental Report 2005, Attachment A - Site Description

    International Nuclear Information System (INIS)

    Cathy A. Wills

    2006-01-01

    This appendix to the ''Nevada Test Site Environmental Report 2005'', dated October 2006 (DOE/NV/11718--1214; DOE/NV/25946--007) expands on the general description of the Nevada Test Site (NTS) presented in the Introduction. Included are subsections that summarize the site?s geological, hydrological, climatological, and ecological setting. The cultural resources of the NTS are also presented. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NTS. An adequate knowledge of the site's environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NTS. The NTS environment contributes to several key features of the site which afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NTS operations. These key features include the general remote location of the NTS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This appendix complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report

  8. Nevada Test Site Environmental Report 2005, Attachment A - Site Description

    Energy Technology Data Exchange (ETDEWEB)

    Cathy A. Wills

    2006-10-01

    This appendix to the ''Nevada Test Site Environmental Report 2005'', dated October 2006 (DOE/NV/11718--1214; DOE/NV/25946--007) expands on the general description of the Nevada Test Site (NTS) presented in the Introduction. Included are subsections that summarize the site?s geological, hydrological, climatological, and ecological setting. The cultural resources of the NTS are also presented. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NTS. An adequate knowledge of the site's environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NTS. The NTS environment contributes to several key features of the site which afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NTS operations. These key features include the general remote location of the NTS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This appendix complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  9. Nevada Test Site Environmental Report 2007 Attachment A: Site Description

    Energy Technology Data Exchange (ETDEWEB)

    Cathy Wills

    2008-09-01

    This appendix expands on the general description of the Nevada Test Site (NTS) presented in the Introduction to the Nevada Test Site Environmental Report 2007 (U.S. Department of Energy [DOE], 2008). Included are subsections that summarize the site's geological, hydrological, climatological, and ecological setting. The cultural resources of the NTS are also presented. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NTS. An adequate knowledge of the site's environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NTS. The NTS environment contributes to several key features of the site which afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NTS operations. These key features include the general remote location of the NTS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  10. Statistical model of fractures and deformations zones for Forsmark. Preliminary site description Forsmark area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    La Pointe, Paul R. [Golder Associate Inc., Redmond, WA (United States); Olofsson, Isabelle; Hermanson, Jan [Golder Associates AB, Uppsala (Sweden)

    2005-04-01

    different high and low fracture intensity intervals in order to capture the variation of this parameter in the model volume. The fracture intensity P32 has been derived by means of simulations for each rock domain and each fracture type, and is expressed as a mean value, and if possible standard deviation and span. The uncertainty in the model has been quantified: for the different geometrical parameters by providing ranges of variations and studying relevant distribution models, by conducting sensitivity analysis on some input data: the effect of truncation of lineaments at the border of the regional model volume and the impact of truncation in outcrop mapping. An alternative conceptual model is under study which is based on the identified deterministic deformation zones, and not on lineaments. An important issue using this model is the bias of information and the limited amount of structures. The current DFN model still contains significant uncertainties which need to be resolved in order to be able to produce a final site DFN model. Three main issues are listed below: The definition of the subhorizontal fracture set in terms of geological processes and tectonics. The size distribution is a critical issue for the hydrogeology of the site. The variation of the fracture intensity by rock domain has been identified but the variation pattern and the spatial distribution within an individual domain are still sufficiently unpredictable that the fracture network permeability structure within a rock domain is uncertain from a conceptual perspective, not just a data uncertainty perspective. Moreover, many rock domains have not yet been sampled by boreholes or outcrops, and thus their fracture properties remain highly uncertain. Validation of the DFN models will require resolution of these two issues, and may also require the drilling of highly inclined or horizontal boreholes. Near-vertical boreholes and the mapping protocol to only map fracture traces in outcrop greater than 0

  11. Statistical model of fractures and deformations zones for Forsmark. Preliminary site description Forsmark area - version 1.2

    International Nuclear Information System (INIS)

    La Pointe, Paul R.; Olofsson, Isabelle; Hermanson, Jan

    2005-04-01

    different high and low fracture intensity intervals in order to capture the variation of this parameter in the model volume. The fracture intensity P32 has been derived by means of simulations for each rock domain and each fracture type, and is expressed as a mean value, and if possible standard deviation and span. The uncertainty in the model has been quantified: for the different geometrical parameters by providing ranges of variations and studying relevant distribution models, by conducting sensitivity analysis on some input data: the effect of truncation of lineaments at the border of the regional model volume and the impact of truncation in outcrop mapping. An alternative conceptual model is under study which is based on the identified deterministic deformation zones, and not on lineaments. An important issue using this model is the bias of information and the limited amount of structures. The current DFN model still contains significant uncertainties which need to be resolved in order to be able to produce a final site DFN model. Three main issues are listed below: The definition of the subhorizontal fracture set in terms of geological processes and tectonics. The size distribution is a critical issue for the hydrogeology of the site. The variation of the fracture intensity by rock domain has been identified but the variation pattern and the spatial distribution within an individual domain are still sufficiently unpredictable that the fracture network permeability structure within a rock domain is uncertain from a conceptual perspective, not just a data uncertainty perspective. Moreover, many rock domains have not yet been sampled by boreholes or outcrops, and thus their fracture properties remain highly uncertain. Validation of the DFN models will require resolution of these two issues, and may also require the drilling of highly inclined or horizontal boreholes. Near-vertical boreholes and the mapping protocol to only map fracture traces in outcrop greater than 0

  12. Statistical analysis of results from the quantitative mapping of fracture minerals in Laxemar. Site descriptive modelling - complementary studies

    Energy Technology Data Exchange (ETDEWEB)

    Loefgren, Martin (Niressa AB, Norsborg (Sweden)); Sidborn, Magnus (Kemakta Konsult AB, Stockholm (Sweden))

    2010-12-15

    generally shown to be small and if comparing the cumulative distribution functions for the data subsets of the 17 rock volumes, more similarities than dissimilarities are found. No general trends can be observed in data with respect to elevation and location of the rock volumes. These conclusions are made from the perspective of radionuclide retention and groundwater composition modelling. Such modelling is not so sensitive to local deviations in fracture mineral abundances, as flow path averaging is of major importance. In other scientific fields, these deviations may be attributed greater importance. It is shown from parametric analyses that the normal distribution fairly well describes the logarithm of d{sub mean} data. Concerning the visible coverage, log{sub 10}(C{sub vis}) data are fairly well described by truncated normal distributions. The distributions fitted to data from the entire site fairly well represent the individual rock volumes. In fractures where the mineral amounts could be quantified, the following means and standard deviations for the normal distribution of log{sub 10}(d{sub mean} [mm]) are suggested: calcite mu = -1.21 and sigma = 0.76, chlorite mu = -0.83 and sigma = 0.48, clay minerals mu = -1.12 and sigma = 0.51, pyrite mu = -4.43 and sigma = 1.17. In fractures where the mineral visible coverage could be estimated, the following parameters for a truncated normal distribution of log{sub 10}(C{sub vis}) are suggested: calcite alpha = 0.96 and beta = 0.65, chlorite alpha = 1.43 and beta = 0.45, clay minerals alpha = 1.39 and beta = 0.41, pyrite alpha = -1.90 and beta = 1.08. For hematite, the data are so scarce that no well founded conclusion can be drawn. The potential correlation between the abundance of fracture minerals and the local transmissivity (which is related to the groundwater flow rate) has been evaluated, but no apparent correlation has been found. However, this evaluation is of preliminary character

  13. Statistical analysis of results from the quantitative mapping of fracture minerals in Forsmark. Site descriptive modelling - complementary studies

    Energy Technology Data Exchange (ETDEWEB)

    Loefgren, Martin (Niressa AB, Norsborg (Sweden)); Sidborn, Magnus (Kemakta Konsult AB, Stockholm (Sweden))

    2010-12-15

    so, the differences are generally shown to be small and if comparing the cumulative distribution functions for the data subsets of the 21 rock volumes, more similarities than dissimilarities are found. No general trends can be observed in data with respect to elevation and location of the rock volumes. These conclusions are made from the perspective of radionuclide retention and groundwater composition modelling. Such modelling is not so sensitive to local deviations in fracture mineral abundances, as flow path averaging is of major importance. In other scientific fields, these deviations may be attributed greater importance. It is shown from parametric analyses that the normal distribution fairly well describes the logarithm of d{sub mean} data. Concerning the visible coverage, log{sub 10}(C{sub vis}) data are fairly well described by truncated normal distributions. The distributions fitted to data from the entire site fairly well represent the individual rock volumes. In fractures where the mineral amounts could be quantified, the following means and standard deviations for the normal distribution of log{sub 10}(d{sub mean} [mm]) are suggested: calcite mu = -1.47 and sigma 0.70, chlorite mu = -0.93 and sigma = 0.46, clay minerals mu = -1.09 and sigma = 0.44, pyrite mu = -4.01 and sigma = 1.26. In fractures where the mineral visible coverage could be estimated, the following parameters for a truncated normal distribution of log{sub 10}(C{sub vis}) are suggested: calcite alpha = 0.85 and beta = 0.65, chlorite alpha =1.38 and beta = 0.51, clay minerals alpha = 1.47 and beta = 0.40, pyrite alpha = -1.52 and beta = 1.18. For hematite, the data are so scarce that no well founded conclusion can be drawn. The potential correlation between the abundance of fracture minerals and the local transmissivity(which is related to the groundwater flow rate) has been evaluated, but no apparent correlation has been found. However, this evaluation is of preliminary character

  14. Premodelling of the importance of the location of the upstream hydraulic boundary of a regional flow model of the Laxemar-Simpevarp area. Site descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Holmen, Johan G.

    2008-03-01

    The location of the westernmost hydraulic boundary of a regional groundwater flow model representing the Laxemar investigation area is of importance as the regional flow of groundwater is primarily from the west towards the sea (as given by the regional topography). If the westernmost boundary condition of a regional flow model is located to close to the investigation area, the regional flow model may underestimate the magnitude of the regional groundwater flow (at the investigation area), as well as overestimate breakthrough times of flow paths from the repository area, etc. Groundwater flows have been calculated by use of two mathematical (numerical) models: A very large groundwater flow model, much larger than the regional flow model used in the Laxemar site description version 1.2, and a smaller flow model that is of a comparable size to the regional model used in the site description. The models are identical except for the different horizontal extensions of the models; the large model extends to the west much further than the small model. The westernmost lateral boundary of the small model is a topographic water divide approx. 7 km from the central parts of the Laxemar investigation area, and the westernmost lateral boundary of the large model is a topographic water divide approx. 40 km from the central parts of the Laxemar investigation area. In the models the lateral boundaries are defined as no-flow boundaries. The objective of the study is to calculate and compare the groundwater flow properties at a tentative repository area at Laxemar; by use of a large flow model and a small flow model. The comparisons include the following three parameters: - Length of flow paths from the tentative repository area. - Advective breakthrough time for flow paths from the tentative repository area. - Magnitude of flow at the tentative repository area. The comparisons demonstrated the following considering the median values of the obtained distributions of flow paths

  15. Nevada Test Site Environmental Report 2008 Attachment A: Site Description

    Energy Technology Data Exchange (ETDEWEB)

    Cathy A. Wills

    2009-09-01

    This attachment expands on the general description of the Nevada Test Site (NTS) presented in the Introduction to the Nevada Test Site Environmental Report 2008 (National Security Technologies, LLC [NSTec], 2009a). Included are subsections that summarize the site’s geological, hydrological, climatological, and ecological setting. The cultural resources of the NTS are also presented. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NTS. An adequate knowledge of the site’s environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NTS. The NTS environment contributes to several key features of the site that afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NTS operations. These key features include the general remote location of the NTS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  16. Nevada Test Site Environmental Report 2009, Attachment A: Site Description

    Energy Technology Data Exchange (ETDEWEB)

    Cathy Wills, ed.

    2010-09-13

    This attachment expands on the general description of the Nevada Test Site (NTS) presented in the Introduction to the Nevada Test Site Environmental Report 2009. Included are subsections that summarize the site’s geological, hydrological, climatological, and ecological setting. The cultural resources of the NTS are also presented. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NTS. An adequate knowledge of the site’s environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NTS. The NTS environment contributes to several key features of the site that afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NTS operations. These key features include the general remote location of the NTS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  17. Preliminary site description Forsmark area - version 1.1

    International Nuclear Information System (INIS)

    2004-03-01

    This report presents the interim version (model version 1.1) of the preliminary Site Descriptive Model for Forsmark. The basis for this interim version is quality-assured, geoscientific and ecological field data from Forsmark that were available in the SKB databases SICADA and GIS at April 30, 2003 as well as version 0 of the Site Descriptive Model. The new data acquired during the initial site investigation phase to the date of data freeze 1.1 constitute the basis for the updating of version 0 to version 1.1. These data originate from surface investigations on the candidate area with its regional environment and from drilling and investigations in boreholes. The surface-based data sets were rather extensive whereas the data sets from boreholes were limited to information from one 1,000 m deep cored borehole (KFM01A) and eight 150 to 200 m deep percussion-drilled boreholes in the Forsmark candidate area. Discipline specific models are developed for a selected regional and local model volume and these are then integrated into a site description. The current methodologies for developing the discipline specific models and the integration of these are documented in methodology reports or strategy reports. In the present work, the guidelines given in those reports were followed to the extent possible with the data and information available at the time for data freeze for model version 1.1. Compared with version 0 there are considerable additional features in the version 1.1, especially in the geological description and in the description of the near surface. The geological models of lithology and deformation zones are based on borehole information and much higher resolution surface data. The existence of highly fractured sub-horizontal zones has been verified and these are now part of the model of the deformation zones. A discrete fracture network (DFN) model has also been developed. The rock mechanics model is based on strength information from SFR and an empirical

  18. Verification study on technology for preliminary investigation for HLW geological disposal. Part 2. Verification of surface geophysical prospecting through establishing site descriptive models

    International Nuclear Information System (INIS)

    Kondo, Hirofumi; Suzuki, Koichi; Hasegawa, Takuma; Goto, Keiichiro; Yoshimura, Kimitaka; Muramoto, Shigenori

    2012-01-01

    The Yokosuka demonstration and validation project using Yokosuka CRIEPI site has been conducted since FY 2006 as a cooperative research between NUMO (Nuclear Waste Management Organization of Japan) and CRIEPI. The objectives of this project are to examine and to refine the basic methodology of the investigation and assessment of properties of geological environment in the stage of Preliminary Investigation for HLW geological disposal. Within Preliminary Investigation technologies, surface geophysical prospecting is an important means of obtaining information from deep geological environment for planning borehole surveys. In FY 2010, both seismic prospecting (seismic reflection and vertical seismic profiling methods) for obtaining information about geological structure and electromagnetic prospecting (magneto-telluric and time domain electromagnetic methods) for obtaining information about resistivity structure reflecting the distribution of salt water/fresh water boundary to a depth of over several hundred meters were conducted in the Yokosuka CRIEPI site. Through these surveys, the contribution of geophysical prospecting methods in the surface survey stage to improving the reliability of site descriptive models was confirmed. (author)

  19. AREST model description

    International Nuclear Information System (INIS)

    Engel, D.W.; McGrail, B.P.

    1993-11-01

    The Office of Civilian Radioactive Waste Management and the Power Reactor and Nuclear Fuel Development Corporation of Japan (PNC) have supported the development of the Analytical Repository Source-Term (AREST) at Pacific Northwest Laboratory. AREST is a computer model developed to evaluate radionuclide release from an underground geologic repository. The AREST code can be used to calculate/estimate the amount and rate of each radionuclide that is released from the engineered barrier system (EBS) of the repository. The EBS is the man-made or disrupted area of the repository. AREST was designed as a system-level models to simulate the behavior of the total repository by combining process-level models for the release from an individual waste package or container. AREST contains primarily analytical models for calculating the release/transport of radionuclides to the lost rock that surrounds each waste package. Analytical models were used because of the small computational overhead that allows all the input parameters to be derived from a statistical distribution. Recently, a one-dimensional numerical model was also incorporated into AREST, to allow for more detailed modeling of the transport process with arbitrary length decay chains. The next step in modeling the EBS, is to develop a model that couples the probabilistic capabilities of AREST with a more detailed process model. This model will need to look at the reactive coupling of the processes that are involved with the release process. Such coupling would include: (1) the dissolution of the waste form, (2) the geochemical modeling of the groundwater, (3) the corrosion of the container overpacking, and (4) the backfill material, just to name a few. Several of these coupled processes are already incorporated in the current version of AREST

  20. A description of LUSTRA's common field sites

    International Nuclear Information System (INIS)

    Berggren, Dan; Bergkvist, Bo; Johansson, Maj-Britt; Melkerud, Per-Arne; Nilsson, Aake; Olsson, Mats; Langvall, Ola; Majdi, Hooshang; Weslien, Per

    2004-01-01

    arena, and thus LUSTRA has gradually put more focus on the Kyoto process. LUSTRA was evaluated during spring 2002 and the general overall statement was that 'The ambitious goals of the LUSTRA program are very good and seem to be well understood by the participating researchers. However, for a second phase a focus on synthesis and synergy is recommended'. In LUSTRA we are performing integrated research on C fluxes at three common field sites (CFS) situated in a south-north transect in Sweden: Asa, Knottaasen and Flakaliden. Measurements started summer 2000. The intention was to establish a climate gradient through Sweden but keep other environmental parameters rather similar. Also within each site the ambition was to get a hydrological gradient going from dry, over mesic to moist conditions, i.e. from deep lying ground water level to shallow groundwater. According to the advises by the reviewers of LUSTRA phase 1, more focus will be on syntheses during LUSTRA phase 2 (2003-2006). However, measurements at the CFS will be continued during 2003 and 2004. The objectives of this paper are (i) to give a general description of the sites, (ii) to describe the abiotic measurements made at the different sites, including the data base, (iii) to describe the methods used to obtain background information about soils and vegetation (C pools and fluxes) and (iv) to present the background information about soils and vegetation

  1. Preliminary site description. Simpevarp area - version 1.1

    International Nuclear Information System (INIS)

    Winberg, Anders

    2004-08-01

    Site characterisation in the Oskarshamn area is currently conducted at two adjoining localities, the Simpevarp and Laxemar subareas. This report presents the interim version (model version Simpevarp 1.1 of S1.1 for short) of the preliminary Site Descriptive Model for the Simpevarp subarea. The basis for this interim version is quality-assured, geoscientific and ecological field data from the Simpevarp subarea (and in part from the Laxemar area) available in the SKB SICADA and GIS data bases as of July 1, 2003 as well as version 0 of the Site Descriptive Model. The new data collected during the initial site investigation phase up till the date of data freeze S1.1 constitute the basis for the update of version 0 to version S1.1. These data include results from surface investigations in the subarea with its regional environment and from drillings and investigations in boreholes. The surface-based data sets were, in a relative sense, extensive compared with data sets from boreholes, were the information largely was limited to information from one c. 1,000 m deep cored borehole (KSH01A), two existing cored boreholes and three c. 200 m deep percussion-drilled boreholes. Discipline-specific models are developed for the selected regional and local model volumes and these models are subsequently integrated into a unified site description. The current methodologies for developing discipline-specific models and their integration are documented in methodology/ strategy reports. In the present work, the procedures and guidelines given in those reports were followed to the extent possible given the data and information available at the time of data freeze for model version S1.1. Compared with version 0 there are considerable additional features in the version S1.1, especially in the geological description and in the description of the near surface. The geological models of lithology and deformation zones are based on borehole information and surface data of much higher

  2. Variable-density groundwater flow simulations and particle tracking. Numerical modelling using DarcyTools. Preliminary site description of the Simpevarp area, version 1.1

    Energy Technology Data Exchange (ETDEWEB)

    Follin, Sven [SF GeoLogic AB, Stockholm (Sweden); Stigsson, Martin; Berglund, Sten [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Svensson, Urban [Computer-aided Fluid Engineering AB, Norrkoeping (Sweden)

    2004-12-01

    SKB is conducting site investigations for a high-level nuclear waste repository in fractured crystalline rocks at two coastal areas in Sweden, Forsmark and Simpevarp. The investigations started in 2002 and have been planned since the late 1990s. The work presented here investigates the possibility of using hydrogeochemical measurements in deep boreholes to reduce parameter uncertainty in a regional modelling of groundwater flow in fractured rock. The work was conducted with the aim of improving the palaeohydrogeological understanding of the Simpevarp area and to give recommendations to the preparations of the next version of the Preliminary Site Description (1.2). The study is based on a large number of numerical simulations of transient variable density groundwater flow through a strongly heterogeneous and anisotropic medium. The simulations were conducted with the computer code DarcyTools, the development of which has been funded by SKB. DarcyTools is a flexible porous media code specifically designed to treat groundwater flow and salt transport in sparsely fractured crystalline rock and it is noted that some of the features presented in this report are still under development or subjected to testing and verification. The simulations reveal the sensitivity of the results to different hydrogeological modelling assumptions, e.g. the sensitivity to the initial groundwater conditions at 10,000 BC, the size of the model domain and boundary conditions, and the hydraulic properties of deterministically and stochastically modelled deformation zones. The outcome of these simulations was compared with measured salinities and calculated relative proportions of different water types (mixing proportions) from measurements in two deep core drilled boreholes in the Laxemar subarea. In addition to the flow simulations, the statistics of flow related transport parameters were calculated for particle flowpaths from repository depth to ground surface for two subareas within the

  3. Variable-density groundwater flow simulations and particle tracking. Numerical modelling using DarcyTools. Preliminary site description of the Simpevarp area, version 1.1

    International Nuclear Information System (INIS)

    Follin, Sven; Stigsson, Martin; Berglund, Sten; Svensson, Urban

    2004-12-01

    SKB is conducting site investigations for a high-level nuclear waste repository in fractured crystalline rocks at two coastal areas in Sweden, Forsmark and Simpevarp. The investigations started in 2002 and have been planned since the late 1990s. The work presented here investigates the possibility of using hydrogeochemical measurements in deep boreholes to reduce parameter uncertainty in a regional modelling of groundwater flow in fractured rock. The work was conducted with the aim of improving the palaeohydrogeological understanding of the Simpevarp area and to give recommendations to the preparations of the next version of the Preliminary Site Description (1.2). The study is based on a large number of numerical simulations of transient variable density groundwater flow through a strongly heterogeneous and anisotropic medium. The simulations were conducted with the computer code DarcyTools, the development of which has been funded by SKB. DarcyTools is a flexible porous media code specifically designed to treat groundwater flow and salt transport in sparsely fractured crystalline rock and it is noted that some of the features presented in this report are still under development or subjected to testing and verification. The simulations reveal the sensitivity of the results to different hydrogeological modelling assumptions, e.g. the sensitivity to the initial groundwater conditions at 10,000 BC, the size of the model domain and boundary conditions, and the hydraulic properties of deterministically and stochastically modelled deformation zones. The outcome of these simulations was compared with measured salinities and calculated relative proportions of different water types (mixing proportions) from measurements in two deep core drilled boreholes in the Laxemar subarea. In addition to the flow simulations, the statistics of flow related transport parameters were calculated for particle flowpaths from repository depth to ground surface for two subareas within the

  4. A proposed descriptive methodology for environmental geologic (envirogeologic) site characterization

    International Nuclear Information System (INIS)

    Schwarz, D.L.; Snyder, W.S.

    1994-01-01

    We propose a descriptive methodology for use in environmental geologic (envirogeologic) site characterization. The method uses traditional sedimentologic descriptions augmented by environmental data needs, and facies analysis. Most other environmental methodologies for soil and sediment characterization use soil engineering and engineering geology techniques that classify by texture and engineering properties. This technique is inadequate for envirogeologic characterization of sediments. In part, this inadequacy is due to differences in the grain-size between the Unified soil Classification and the Udden-Wentworth scales. Use of the soil grain-size classification could easily cause confusion when attempting to relate descriptions based on this classification to our basic understanding of sedimentary depositional systems. The proposed envirogeologic method uses descriptive parameters to characterize a sediment sample, suggests specific tests on samples for adequate characterization, and provides a guidelines for subsurface facies analysis, based on data retrieved from shallow boreholes, that will allow better predictive models to be developed. This methodology should allow for both a more complete site assessment, and provide sufficient data for selection of the appropriate remediation technology, including bioremediation. 50 refs

  5. Preliminary site description Forsmark area - version 1.1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-03-01

    This report presents the interim version (model version 1.1) of the preliminary Site Descriptive Model for Forsmark. The basis for this interim version is quality-assured, geoscientific and ecological field data from Forsmark that were available in the SKB databases SICADA and GIS at April 30, 2003 as well as version 0 of the Site Descriptive Model. The new data acquired during the initial site investigation phase to the date of data freeze 1.1 constitute the basis for the updating of version 0 to version 1.1. These data originate from surface investigations on the candidate area with its regional environment and from drilling and investigations in boreholes. The surface-based data sets were rather extensive whereas the data sets from boreholes were limited to information from one 1,000 m deep cored borehole (KFM01A) and eight 150 to 200 m deep percussion-drilled boreholes in the Forsmark candidate area. Discipline specific models are developed for a selected regional and local model volume and these are then integrated into a site description. The current methodologies for developing the discipline specific models and the integration of these are documented in methodology reports or strategy reports. In the present work, the guidelines given in those reports were followed to the extent possible with the data and information available at the time for data freeze for model version 1.1. Compared with version 0 there are considerable additional features in the version 1.1, especially in the geological description and in the description of the near surface. The geological models of lithology and deformation zones are based on borehole information and much higher resolution surface data. The existence of highly fractured sub-horizontal zones has been verified and these are now part of the model of the deformation zones. A discrete fracture network (DFN) model has also been developed. The rock mechanics model is based on strength information from SFR and an empirical

  6. Meteorological, hydrological and hydrogeological monitoring data and near-surface hydrogeological properties data from Laxemar-Simpevarp. Site descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Werner, Kent; Oehman, Johan; Holgersson, Bjoern; Roennback, Kristoffer; Marelius, Fredrick

    2008-12-01

    This report presents and analyses meteorological, hydrological and hydrogeological time-series data and near-surface hydrogeological properties data from the Laxemar-Simpevarp area, available in SKB's Sicada database at time of the Laxemar 2.3 data freeze (Aug. 31, 2007). The meteorological data set includes data from two local stations, located on the island of Aespoe and at Plittorp, located further inland. In addition, the data evaluation uses a longer-term data set from 7 surrounding stations, operated by SMHI. As part of this study, a time series is constructed of the water content of snow. According to the data evaluation, the site-average annual precipitation and potential evapotranspiration can be estimated to be on the order of 600 and 535 mm, respectively. In particular, precipitation demonstrates a near-coastal gradient, with less precipitation at the coast compared to areas further inland. The surface-water level data set includes data from 4 lake-level gauging stations and 3 sea-level gauging stations. All lakes are located above sea level, including the near-coastal Lake Soeraa. Hence, no intrusion of sea water to lakes takes place. There is a strong co-variation among the monitored lake-water levels, typically with maxima during spring and minima during late summer and early autumn. Concerning the sea as a hydraulic boundary, the maximum and minimum sea levels (daily averages) during the site-investigation period were -0.52 and 0.71 metres above sea level, respectively, whereas the average sea level was 0.03 metres above sea level (RHB 70). The data set on stream discharge, surface-water temperature and electrical conductivity includes data from 9 discharge-gauging stations in 7 streams. Based on the discharge data, the site-average specific discharge for the years 2005-2007 can be estimated to 165 mm/y, which is within the interval of the estimated long-term average. Overall, discharge-data errors are likely to be small. The hydrogeological time

  7. Meteorological, hydrological and hydrogeological monitoring data and near-surface hydrogeological properties data from Laxemar-Simpevarp. Site descriptive modelling SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Werner, Kent (EmpTec, Taeby (Sweden)); Oehman, Johan (Golder Associates AB, Stockholm (Sweden)); Holgersson, Bjoern (SWECO VIAK, Stockholm (Sweden)); Roennback, Kristoffer (Aqualog AB, Goeteborg (Sweden)); Marelius, Fredrick (WSP Sverige, Stockholm (Sweden))

    2008-12-15

    This report presents and analyses meteorological, hydrological and hydrogeological time-series data and near-surface hydrogeological properties data from the Laxemar-Simpevarp area, available in SKB's Sicada database at time of the Laxemar 2.3 data freeze (Aug. 31, 2007). The meteorological data set includes data from two local stations, located on the island of Aespoe and at Plittorp, located further inland. In addition, the data evaluation uses a longer-term data set from 7 surrounding stations, operated by SMHI. As part of this study, a time series is constructed of the water content of snow. According to the data evaluation, the site-average annual precipitation and potential evapotranspiration can be estimated to be on the order of 600 and 535 mm, respectively. In particular, precipitation demonstrates a near-coastal gradient, with less precipitation at the coast compared to areas further inland. The surface-water level data set includes data from 4 lake-level gauging stations and 3 sea-level gauging stations. All lakes are located above sea level, including the near-coastal Lake Soeraa. Hence, no intrusion of sea water to lakes takes place. There is a strong co-variation among the monitored lake-water levels, typically with maxima during spring and minima during late summer and early autumn. Concerning the sea as a hydraulic boundary, the maximum and minimum sea levels (daily averages) during the site-investigation period were -0.52 and 0.71 metres above sea level, respectively, whereas the average sea level was 0.03 metres above sea level (RHB 70). The data set on stream discharge, surface-water temperature and electrical conductivity includes data from 9 discharge-gauging stations in 7 streams. Based on the discharge data, the site-average specific discharge for the years 2005-2007 can be estimated to 165 mm/y, which is within the interval of the estimated long-term average. Overall, discharge-data errors are likely to be small. The hydrogeological

  8. Preliminary site description. Simpevarp area - version 1.1

    Energy Technology Data Exchange (ETDEWEB)

    Winberg, Anders [ed.

    2004-08-01

    Site characterisation in the Oskarshamn area is currently conducted at two adjoining localities, the Simpevarp and Laxemar subareas. This report presents the interim version (model version Simpevarp 1.1 of S1.1 for short) of the preliminary Site Descriptive Model for the Simpevarp subarea. The basis for this interim version is quality-assured, geoscientific and ecological field data from the Simpevarp subarea (and in part from the Laxemar area) available in the SKB SICADA and GIS data bases as of July 1, 2003 as well as version 0 of the Site Descriptive Model. The new data collected during the initial site investigation phase up till the date of data freeze S1.1 constitute the basis for the update of version 0 to version S1.1. These data include results from surface investigations in the subarea with its regional environment and from drillings and investigations in boreholes. The surface-based data sets were, in a relative sense, extensive compared with data sets from boreholes, were the information largely was limited to information from one c. 1,000 m deep cored borehole (KSH01A), two existing cored boreholes and three c. 200 m deep percussion-drilled boreholes. Discipline-specific models are developed for the selected regional and local model volumes and these models are subsequently integrated into a unified site description. The current methodologies for developing discipline-specific models and their integration are documented in methodology/ strategy reports. In the present work, the procedures and guidelines given in those reports were followed to the extent possible given the data and information available at the time of data freeze for model version S1.1. Compared with version 0 there are considerable additional features in the version S1.1, especially in the geological description and in the description of the near surface. The geological models of lithology and deformation zones are based on borehole information and surface data of much higher

  9. Preliminary site description Simpevarp subarea - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Winberg, Anders [ed.

    2005-04-01

    The objectives of the version 1.2 site descriptive modelling (SDM) of the Simpevarp subarea are to produce and document an integrated description of the site and its regional environments based on the site-specific data available from the initial site investigations and to give recommendations on continued investigations on a continuous basis. The modelling work is based on primary data available at the time of the data freeze for Simpevarp 1.2, April 1, 2004. The local scale model area (24 km{sup 2}) for the Simpevarp 1.2 modelling encompasses both the Simpevarp and Laxemar subareas. The local model area is located in the centre of a regional scale model area (273 km{sup 2}). Surface ecosystem models in terms of pools and fluxes of carbon have been developed for the terrestrial (e.g. plants and animals) and limnic (e.g. algae and fish) systems using the Lake Frisksjoen drainage area. Furthermore, a first marine ecosystem model has been developed for the Basin Borholmsfjaerden. Three principal lithological domains have been defined in the subarea, an A domain that is dominated by the Aevroe granite, a domain B that is dominated by the fine-grained dioritoid, a C domain that is characterised by a mixture of of Aevroe granite and quartz monzodiorite. A fourth domain is made up a few scattered domains of diorite to gabbro. In total, 22 deformation zones with high confidence of occurrence have been interpreted in the local scale model area. The understanding of the interpreted deformation zones of the Simpevarp subarea is considered adequate to make a preliminary assessment of available storage volumes for a deep repository. High rock stresses do not appear to be a major concern for the Simpevarp subarea. The magnitude of the maximum principal stress at 500 m in the Simpevarp subarea is estimated at 10-22 MPa. The analysis of the thermal conductivity has developed considerably since Simpevarp 1.1. In terms of interpreted mean values for the identified lithological

  10. Preliminary site description Simpevarp subarea - version 1.2

    International Nuclear Information System (INIS)

    Winberg, Anders

    2005-04-01

    The objectives of the version 1.2 site descriptive modelling (SDM) of the Simpevarp subarea are to produce and document an integrated description of the site and its regional environments based on the site-specific data available from the initial site investigations and to give recommendations on continued investigations on a continuous basis. The modelling work is based on primary data available at the time of the data freeze for Simpevarp 1.2, April 1, 2004. The local scale model area (24 km 2 ) for the Simpevarp 1.2 modelling encompasses both the Simpevarp and Laxemar subareas. The local model area is located in the centre of a regional scale model area (273 km 2 ). Surface ecosystem models in terms of pools and fluxes of carbon have been developed for the terrestrial (e.g. plants and animals) and limnic (e.g. algae and fish) systems using the Lake Frisksjoen drainage area. Furthermore, a first marine ecosystem model has been developed for the Basin Borholmsfjaerden. Three principal lithological domains have been defined in the subarea, an A domain that is dominated by the Aevroe granite, a domain B that is dominated by the fine-grained dioritoid, a C domain that is characterised by a mixture of of Aevroe granite and quartz monzodiorite. A fourth domain is made up a few scattered domains of diorite to gabbro. In total, 22 deformation zones with high confidence of occurrence have been interpreted in the local scale model area. The understanding of the interpreted deformation zones of the Simpevarp subarea is considered adequate to make a preliminary assessment of available storage volumes for a deep repository. High rock stresses do not appear to be a major concern for the Simpevarp subarea. The magnitude of the maximum principal stress at 500 m in the Simpevarp subarea is estimated at 10-22 MPa. The analysis of the thermal conductivity has developed considerably since Simpevarp 1.1. In terms of interpreted mean values for the identified lithological domains, the

  11. Hanford Site existing irradiated fuel storage facilities description

    Energy Technology Data Exchange (ETDEWEB)

    Willis, W.L.

    1995-01-11

    This document describes facilities at the Hanford Site which are currently storing spent nuclear fuels. The descriptions provide a basis for the no-action alternatives of ongoing and planned National Environmental Protection Act reviews.

  12. LANL environmental restoration site ranking system: System description. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Merkhofer, L.; Kann, A.; Voth, M. [Applied Decision Analysis, Inc., Menlo Park, CA (United States)

    1992-10-13

    The basic structure of the LANL Environmental Restoration (ER) Site Ranking System and its use are described in this document. A related document, Instructions for Generating Inputs for the LANL ER Site Ranking System, contains detailed descriptions of the methods by which necessary inputs for the system will be generated. LANL has long recognized the need to provide a consistent basis for comparing the risks and other adverse consequences associated with the various waste problems at the Lab. The LANL ER Site Ranking System is being developed to help address this need. The specific purpose of the system is to help improve, defend, and explain prioritization decisions at the Potential Release Site (PRS) and Operable Unit (OU) level. The precise relationship of the Site Ranking System to the planning and overall budget processes is yet to be determined, as the system is still evolving. Generally speaking, the Site Ranking System will be used as a decision aid. That is, the system will be used to aid in the planning and budgetary decision-making process. It will never be used alone to make decisions. Like all models, the system can provide only a partial and approximate accounting of the factors important to budget and planning decisions. Decision makers at LANL will have to consider factors outside of the formal system when making final choices. Some of these other factors are regulatory requirements, DOE policy, and public concern. The main value of the site ranking system, therefore, is not the precise numbers it generates, but rather the general insights it provides.

  13. LANL environmental restoration site ranking system: System description. Final report

    International Nuclear Information System (INIS)

    Merkhofer, L.; Kann, A.; Voth, M.

    1992-01-01

    The basic structure of the LANL Environmental Restoration (ER) Site Ranking System and its use are described in this document. A related document, Instructions for Generating Inputs for the LANL ER Site Ranking System, contains detailed descriptions of the methods by which necessary inputs for the system will be generated. LANL has long recognized the need to provide a consistent basis for comparing the risks and other adverse consequences associated with the various waste problems at the Lab. The LANL ER Site Ranking System is being developed to help address this need. The specific purpose of the system is to help improve, defend, and explain prioritization decisions at the Potential Release Site (PRS) and Operable Unit (OU) level. The precise relationship of the Site Ranking System to the planning and overall budget processes is yet to be determined, as the system is still evolving. Generally speaking, the Site Ranking System will be used as a decision aid. That is, the system will be used to aid in the planning and budgetary decision-making process. It will never be used alone to make decisions. Like all models, the system can provide only a partial and approximate accounting of the factors important to budget and planning decisions. Decision makers at LANL will have to consider factors outside of the formal system when making final choices. Some of these other factors are regulatory requirements, DOE policy, and public concern. The main value of the site ranking system, therefore, is not the precise numbers it generates, but rather the general insights it provides

  14. Preliminary Hydrogeochemical Site Description SFR (version 0.2)

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, Ann-Chatrin (Geosigma AB, Uppaala (Sweden)); Tullborg, Eva-Lena (Terralogica AB, Graabo (Sweden)); Smellie, John (Conterra AB, Partille (Sweden))

    2010-05-15

    The final repository for low and intermediate level radioactive operational waste, SFR, located about 150 km north of Stockholm, is to undergo a future extension. The present on-going project, scheduled from 2007 to 2011, is to define and characterise a suitable bedrock volume for the extended repository. This will include the drilling and geoscientific evaluation of seven core-drilled and four percussion boreholes as well as subsequent interpretation and modelling based on the obtained results in order to provide the necessary information for safety assessment and repository design. This report presents a preliminary hydrogeochemical site description for the SFR site and should be considered as an early progress report rather than a complete hydrochemical site descriptive model. The completed hydrogeochemical field investigations have yielded chemical data from a total of 12 borehole sections in five boreholes and additional data from the entire length of two open boreholes in connection with hydraulic tests. These data, together with data from a total of 18 early boreholes in the present SFR tunnel system, were used in the interpretation work. The main part of the data consisted of basic groundwater analyses including major ions and isotopes. Some sporadic gas, microbe and measured redox data are available, but these are either not treated in this report, or are only briefly discussed. This was due to time constraints since special care is needed when interpreting few data of varying quality. The groundwaters in the SFR dataset cover a maximum depth down to about .400 masl and represent a relatively limited salinity range (1,500 to 5,500 mg/L chloride). However, the delta18O values show a wide variation (-1.55 to -0.75% V-SMOW) similar to that reported from the Forsmark site investigations. At the SFR, marine indicators such as Mg/Cl, K/Cl and Br/Cl also show relatively large variations considering the limited salinity range. From very few measured Eh values, and

  15. Preliminary Hydrogeochemical Site Description SFR (version 0.2)

    International Nuclear Information System (INIS)

    Nilsson, Ann-Chatrin; Tullborg, Eva-Lena; Smellie, John

    2010-05-01

    The final repository for low and intermediate level radioactive operational waste, SFR, located about 150 km north of Stockholm, is to undergo a future extension. The present on-going project, scheduled from 2007 to 2011, is to define and characterise a suitable bedrock volume for the extended repository. This will include the drilling and geoscientific evaluation of seven core-drilled and four percussion boreholes as well as subsequent interpretation and modelling based on the obtained results in order to provide the necessary information for safety assessment and repository design. This report presents a preliminary hydrogeochemical site description for the SFR site and should be considered as an early progress report rather than a complete hydrochemical site descriptive model. The completed hydrogeochemical field investigations have yielded chemical data from a total of 12 borehole sections in five boreholes and additional data from the entire length of two open boreholes in connection with hydraulic tests. These data, together with data from a total of 18 early boreholes in the present SFR tunnel system, were used in the interpretation work. The main part of the data consisted of basic groundwater analyses including major ions and isotopes. Some sporadic gas, microbe and measured redox data are available, but these are either not treated in this report, or are only briefly discussed. This was due to time constraints since special care is needed when interpreting few data of varying quality. The groundwaters in the SFR dataset cover a maximum depth down to about .400 masl and represent a relatively limited salinity range (1,500 to 5,500 mg/L chloride). However, the δ 18 O values show a wide variation (-1.55 to -0.75% V-SMOW) similar to that reported from the Forsmark site investigations. At the SFR, marine indicators such as Mg/Cl, K/Cl and Br/Cl also show relatively large variations considering the limited salinity range. From very few measured Eh values, and

  16. Analysis of laparoscopic port site complications: A descriptive study.

    Science.gov (United States)

    Karthik, Somu; Augustine, Alfred Joseph; Shibumon, Mundunadackal Madhavan; Pai, Manohar Varadaraya

    2013-04-01

    The rate of port site complications following conventional laparoscopic surgery is about 21 per 100,000 cases. It has shown a proportional rise with increase in the size of the port site incision and trocar. Although rare, complications that occur at the port site include infection, bleeding, and port site hernia. To determine the morbidity associated with ports at the site of their insertion in laparoscopic surgery and to identify risk factors for complications. Prospective descriptive study. In the present descriptive study, a total of 570 patients who underwent laparoscopic surgeries for various ailments between August 2009 and July 2011 at our institute were observed for port site complications prospectively and the complications were reviewed. Descriptive statistical analysis was carried out in the present study. The statistical software, namely, SPSS 15.0 was used for the analysis of the data. Of the 570 patients undergoing laparoscopic surgery, 17 (3%) had developed complications specifically related to the port site during a minimum follow-up of three months; port site infection (PSI) was the most frequent (n = 10, 1.8%), followed by port site bleeding (n = 4, 0.7%), omentum-related complications (n = 2; 0.35%), and port site metastasis (n = 1, 0.175%). Laparoscopic surgeries are associated with minimal port site complications. Complications are related to the increased number of ports. Umbilical port involvement is the commonest. Most complications are manageable with minimal morbidity, and can be further minimized with meticulous surgical technique during entry and exit.

  17. Site description of the SFR area at Forsmark at completion of the site investigation phase. SDM-PSU Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-05-15

    The site descriptive model (SDM) presented in this report is an integrated model for bedrock geology, rock mechanics, bedrock hydrogeology and bedrock hydrogeochemistry of the site investigated in the SFR extension project (PSU). A description of the surface system is also included in the report. However, the surface system is not integrated with the other disciplines as new data regarding the surface system will not be available until after the completion of SDM-PSU. It is noted that SDM-PSU does not include all disciplines handled in SDM-Site Forsmark (SKB 2008b), the focus is to produce a site description that meets the needs of the SFR extension project. The overall objective of the SFR extension project is to have the application for the extension ready by 2013. This report presents an integrated site model incorporating the historic data acquired from the investigations for and construction of the existing SFR facility (1980-1986), as well as from the recent investigations for the planned extension of SFR (2008-2009). It also provides a summary of the abundant underlying data and the discipline-specific models that support the integrated site model. The description relies heavily on background reports concerning detailed data analyses and modelling in the different disciplines. It is noteworthy that the investigations conducted during the SFR extension project were guided by the choice of site prior to the investigations, which was based on the experience gained during the construction of the existing SFR facility.

  18. Site description of the SFR area at Forsmark at completion of the site investigation phase. SDM-PSU Forsmark

    International Nuclear Information System (INIS)

    2013-05-01

    The site descriptive model (SDM) presented in this report is an integrated model for bedrock geology, rock mechanics, bedrock hydrogeology and bedrock hydrogeochemistry of the site investigated in the SFR extension project (PSU). A description of the surface system is also included in the report. However, the surface system is not integrated with the other disciplines as new data regarding the surface system will not be available until after the completion of SDM-PSU. It is noted that SDM-PSU does not include all disciplines handled in SDM-Site Forsmark (SKB 2008b), the focus is to produce a site description that meets the needs of the SFR extension project. The overall objective of the SFR extension project is to have the application for the extension ready by 2013. This report presents an integrated site model incorporating the historic data acquired from the investigations for and construction of the existing SFR facility (1980-1986), as well as from the recent investigations for the planned extension of SFR (2008-2009). It also provides a summary of the abundant underlying data and the discipline-specific models that support the integrated site model. The description relies heavily on background reports concerning detailed data analyses and modelling in the different disciplines. It is noteworthy that the investigations conducted during the SFR extension project were guided by the choice of site prior to the investigations, which was based on the experience gained during the construction of the existing SFR facility

  19. Analysis of laparoscopic port site complications: A descriptive study

    Directory of Open Access Journals (Sweden)

    Somu Karthik

    2013-01-01

    Full Text Available Context: The rate of port site complications following conventional laparoscopic surgery is about 21 per 100,000 cases. It has shown a proportional rise with increase in the size of the port site incision and trocar. Although rare, complications that occur at the port site include infection, bleeding, and port site hernia. Aims: To determine the morbidity associated with ports at the site of their insertion in laparoscopic surgery and to identify risk factors for complications. Settings and Design: Prospective descriptive study. Materials and Methods: In the present descriptive study, a total of 570 patients who underwent laparoscopic surgeries for various ailments between August 2009 and July 2011 at our institute were observed for port site complications prospectively and the complications were reviewed. Statistical Analysis Used: Descriptive statistical analysis was carried out in the present study. The statistical software, namely, SPSS 15.0 was used for the analysis of the data. Results: Of the 570 patients undergoing laparoscopic surgery, 17 (3% had developed complications specifically related to the port site during a minimum follow-up of three months; port site infection (PSI was the most frequent (n = 10, 1.8%, followed by port site bleeding (n = 4, 0.7%, omentum-related complications (n = 2; 0.35%, and port site metastasis (n = 1, 0.175%. Conclusions: Laparoscopic surgeries are associated with minimal port site complications. Complications are related to the increased number of ports. Umbilical port involvement is the commonest. Most complications are manageable with minimal morbidity, and can be further minimized with meticulous surgical technique during entry and exit.

  20. Analysis of laparoscopic port site complications: A descriptive study

    Science.gov (United States)

    Karthik, Somu; Augustine, Alfred Joseph; Shibumon, Mundunadackal Madhavan; Pai, Manohar Varadaraya

    2013-01-01

    CONTEXT: The rate of port site complications following conventional laparoscopic surgery is about 21 per 100,000 cases. It has shown a proportional rise with increase in the size of the port site incision and trocar. Although rare, complications that occur at the port site include infection, bleeding, and port site hernia. AIMS: To determine the morbidity associated with ports at the site of their insertion in laparoscopic surgery and to identify risk factors for complications. SETTINGS AND DESIGN: Prospective descriptive study. MATERIALS AND METHODS: In the present descriptive study, a total of 570 patients who underwent laparoscopic surgeries for various ailments between August 2009 and July 2011 at our institute were observed for port site complications prospectively and the complications were reviewed. STATISTICAL ANALYSIS USED: Descriptive statistical analysis was carried out in the present study. The statistical software, namely, SPSS 15.0 was used for the analysis of the data. RESULTS: Of the 570 patients undergoing laparoscopic surgery, 17 (3%) had developed complications specifically related to the port site during a minimum follow-up of three months; port site infection (PSI) was the most frequent (n = 10, 1.8%), followed by port site bleeding (n = 4, 0.7%), omentum-related complications (n = 2; 0.35%), and port site metastasis (n = 1, 0.175%). CONCLUSIONS: Laparoscopic surgeries are associated with minimal port site complications. Complications are related to the increased number of ports. Umbilical port involvement is the commonest. Most complications are manageable with minimal morbidity, and can be further minimized with meticulous surgical technique during entry and exit. PMID:23741110

  1. The Agincourt demographic and health study - site description ...

    African Journals Online (AJOL)

    The Agincourt demographic and health study - site description, baseline findings and implications. Stephen M Tollman, Kobus Herbst, Michel Garenne, John S.S. Gear, KathJeen Kahn. Abstract. No Abstract. Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

  2. Probabilistic Description of a Clay Site using CPTU tests

    DEFF Research Database (Denmark)

    Andersen, Sarah; Lauridsen, Kristoffer; Nielsen, Benjaminn Nordahl

    2012-01-01

    A clay site at the harbour of Aarhus, where numerous cone penetration tests have been conducted, is assessed. The upper part of the soil deposit is disregarded, and only the clay sections are investigated. The thickness of the clay deposit varies from 5 to 6 meters, and is sliced into sections of...... a geotechnical assessment of a site, using both the method for classifying soil behaviour types and applying statistics, yield a new level of information, and certainty about the estimates of the strength parameters which are the important outcome of such a site description.......A clay site at the harbour of Aarhus, where numerous cone penetration tests have been conducted, is assessed. The upper part of the soil deposit is disregarded, and only the clay sections are investigated. The thickness of the clay deposit varies from 5 to 6 meters, and is sliced into sections of 1...... meter in thickness. For each slice, a map of the variation of the undrained shear strength is created through Kriging and the probability of finding weak zones in the deposit is calculated. This results in a description of the spatial variation of the undrained shear strength at the site. Making...

  3. Human population and activities in Forsmark. Site description

    Energy Technology Data Exchange (ETDEWEB)

    Miliander, Sofia; Punakivi, Mari; Kylaekorpi, Lasse; Rydgren, Bernt [SwedPower AB, Stockholm (Sweden)

    2004-12-01

    The Swedish Nuclear Fuel and Waste Management Co (SKB) is in the process of selecting a safe and environmentally acceptable location for a deep repository of radioactive waste. Two alternative locations are under investigation. These are Forsmark, Oesthammars kommun (kommun = municipality) and Simpevarp/Laxemar, Oskarshamns kommun. SKB has expressed the importance of describing the humans and their activities in these areas and therefore has this synthesis concerning the human population in Forsmark been produced.The description is a statistical synthesis, mainly based upon statistical data from SCB (Statistics Sweden) that has been collected, processed and analysed. The statistical data has not been verified through site inspections and interviews. When using statistical data, it is advisable to note that the data becomes more unreliable if the areas are small, with small populations.The data in this description is essential for future evaluations of the impact on the environment and its human population (Environmental Impact Assessments). The data is also important when modelling the potential flows of radio nuclides and calculating the risk of exposure in future safety assessments.The actual area for the study is in this report called 'the Forsmark area', an area of 19.5 km{sup 2} near Forsmark nuclear power plant. The land use in the Forsmark area differs notably from the land use in Uppsala laen (laen = county). Only 0.04% of the total area is developed (built-up) compared to 4.9% in Uppsala laen and only 4% is agricultural land compared to 25% in the county. Furthermore, there are far more forest, wetlands and water areas in the Forsmark area. The forest area represents as much as 72.5% of the total area.The Forsmark area is uninhabited, and its surroundings are very sparsely populated. In 2002, the population density in Forsmark was 1.8 inhabitants per square kilometre, which was 24 times lower than in Uppsala laen. The population density in the

  4. Human population and activities in Forsmark. Site description

    International Nuclear Information System (INIS)

    Miliander, Sofia; Punakivi, Mari; Kylaekorpi, Lasse; Rydgren, Bernt

    2004-12-01

    The Swedish Nuclear Fuel and Waste Management Co (SKB) is in the process of selecting a safe and environmentally acceptable location for a deep repository of radioactive waste. Two alternative locations are under investigation. These are Forsmark, Oesthammars kommun (kommun = municipality) and Simpevarp/Laxemar, Oskarshamns kommun. SKB has expressed the importance of describing the humans and their activities in these areas and therefore has this synthesis concerning the human population in Forsmark been produced.The description is a statistical synthesis, mainly based upon statistical data from SCB (Statistics Sweden) that has been collected, processed and analysed. The statistical data has not been verified through site inspections and interviews. When using statistical data, it is advisable to note that the data becomes more unreliable if the areas are small, with small populations.The data in this description is essential for future evaluations of the impact on the environment and its human population (Environmental Impact Assessments). The data is also important when modelling the potential flows of radio nuclides and calculating the risk of exposure in future safety assessments.The actual area for the study is in this report called 'the Forsmark area', an area of 19.5 km 2 near Forsmark nuclear power plant. The land use in the Forsmark area differs notably from the land use in Uppsala laen (laen = county). Only 0.04% of the total area is developed (built-up) compared to 4.9% in Uppsala laen and only 4% is agricultural land compared to 25% in the county. Furthermore, there are far more forest, wetlands and water areas in the Forsmark area. The forest area represents as much as 72.5% of the total area.The Forsmark area is uninhabited, and its surroundings are very sparsely populated. In 2002, the population density in Forsmark was 1.8 inhabitants per square kilometre, which was 24 times lower than in Uppsala laen. The population density in the parish has been

  5. Ecosystem description of a drainage area - a strategy in biosphere descriptions during site investigations for a repository of spent nuclear fuel

    International Nuclear Information System (INIS)

    Lindborg, T.; Lofgren, A.

    2004-01-01

    During the next few years the Swedish Nuclear Fuel and Waste Management Co. (SKB) performs site investigations at two sites in Sweden for a future repository of spent nuclear fuel. Novel methods based on systems and landscape ecology are developed to understand and model the radionuclide flow in the biosphere using site specific data for a safety assessment. This work describes the strategy for development of a descriptive ecosystem model for the surface ecosystem. The site description is needed to: a) perform a safety assessment that describes and analyzes different scenarios for radionuclide releases into the ecosystem and possible pathways for dispersal or accumulation radionuclides in the ecosystem, b) detect changes caused by the construction of a repository, c) establish a baseline for detecting long-term effects of the repository. The description adopts a site-specific approach focusing on the quantification of the properties that will constitute the descriptive model. The aim is also to present the methodology for determining the properties, to describe the development of the framework for the descriptive ecosystem models by integrating use of different properties, and finally, to present vital data from other site descriptive models such as those for geology or hydrogeology. The safety assessment will use an approach, among other methods, where transport and accumulation of radionuclides will be modelled by quantifying biogeochemical pathways of matter. The descriptive ecosystem model applied to the site was therefore built to describe and quantify processes affecting i.e. turnover of matter in a drainage area. The conclusions from applying this approach was that by have estimating the flow of matter the ecological and physical constrains on the system reduces the potential variations in outcome of future states of the ecosystem and thus also reduces the uncertainties in estimating radionuclide flow and consequences to humans and the environment. (author)

  6. Description of reference (model) plant

    International Nuclear Information System (INIS)

    Schneider, R.A.

    1984-01-01

    For the workshop on Safeguards System design for a fuel fabrication plant, a generic example of a LEU bulk-handling facility that is based on the Exxon LWR fuel fabrication plants is used. The model plant information is given in the following separate sections: (1) process assumptions; (2) six-month material balance model; (3) measurements; (4) error parameters, measurements, and sigma MUF calculations; (5) material control areas; (6) accounting, records, and reports; (7) tamper-safing; and (8) measurement control program

  7. Description of the Lewin Natural Gas Model

    International Nuclear Information System (INIS)

    Kuuskraa, V.; Godec, M.

    1989-01-01

    This paper provides a brief description of the Lewin Natural Gas Model, shows how this model differs in key features from the other models participating in EMF-9, and describes how the different modeling scenarios analyzed in EMF-9 were implemented in the Lewin model. This background helps explain the key results that have been gained from applying the Lewin model to the EMF scenarios

  8. Towards reproducible descriptions of neuronal network models.

    Directory of Open Access Journals (Sweden)

    Eilen Nordlie

    2009-08-01

    Full Text Available Progress in science depends on the effective exchange of ideas among scientists. New ideas can be assessed and criticized in a meaningful manner only if they are formulated precisely. This applies to simulation studies as well as to experiments and theories. But after more than 50 years of neuronal network simulations, we still lack a clear and common understanding of the role of computational models in neuroscience as well as established practices for describing network models in publications. This hinders the critical evaluation of network models as well as their re-use. We analyze here 14 research papers proposing neuronal network models of different complexity and find widely varying approaches to model descriptions, with regard to both the means of description and the ordering and placement of material. We further observe great variation in the graphical representation of networks and the notation used in equations. Based on our observations, we propose a good model description practice, composed of guidelines for the organization of publications, a checklist for model descriptions, templates for tables presenting model structure, and guidelines for diagrams of networks. The main purpose of this good practice is to trigger a debate about the communication of neuronal network models in a manner comprehensible to humans, as opposed to machine-readable model description languages. We believe that the good model description practice proposed here, together with a number of other recent initiatives on data-, model-, and software-sharing, may lead to a deeper and more fruitful exchange of ideas among computational neuroscientists in years to come. We further hope that work on standardized ways of describing--and thinking about--complex neuronal networks will lead the scientific community to a clearer understanding of high-level concepts in network dynamics, and will thus lead to deeper insights into the function of the brain.

  9. Emplacement mechanisms and structural influences of a younger granite intrusion into older wall rocks - a principal study with application to the Goetemar and Uthammar granites. Site-descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Cruden, Alexander R.

    2008-12-01

    The c. 1.80 Ga old bedrock in the Laxemar-Simpevarp area, which is the focus of the site investigation at Oskarshamn, is dominated by intrusive rocks belonging to the c. 1.86-1.65 Ga Transscandinavian Igneous Belt (TIB). However, the site investigation area is situated in between two c. 1.45 Ga old anorogenic granites, the Goetemar granite in the north and the Uthammar granite in the south. This study evaluates the emplacement mechanism of these intrusions and their structural influence on the older bedrock. Field observations and structural measurements indicate that both the Goetemar and the Uthammar granites are discordant and have not imposed any significant ductile deformation on their wall-rocks. The apparent conformity of geological contacts and fabrics in the wall rocks and the southern margin of the Goetemar granite is coincidental and inherited from the pattern of Svecokarelian deformation of the TIB. However, interpretation of regional aeromagnetic data suggests that the granites occur within a broad, NNE-SSW trending linear belt, pointing to deep seated tectonic control on their generation, ascent and emplacement. Thermochronology indicates that the granites were emplaced at depths between 4 and 8 km into brittle wall rocks. The 3-D shape of the Goetemar and Uthammar plutons has been investigated by 2.75D forward modelling of the residual gravity anomalies due to both granites. Both granites are associated with strong residual gravity anomalies of up to -10 mgal. Constraints on the geometry of the plutons at the surface are provided from surface geology maps and several deep boreholes located on or close to the model profiles. A further variable in the gravity modelling is introduced by either allowing the upper contact of the plutons to assume the most suitable orientation to produce the best fit between the modelled and observed gravity ('unconstrained models') or by forcing the near surface orientation of the contacts to be vertical ('constrained

  10. Emplacement mechanisms and structural influences of a younger granite intrusion into older wall rocks - a principal study with application to the Goetemar and Uthammar granites. Site-descriptive modelling SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Cruden, Alexander R. (Dept. of Geology, Univ. of Toronto (Canada))

    2008-12-15

    The c. 1.80 Ga old bedrock in the Laxemar-Simpevarp area, which is the focus of the site investigation at Oskarshamn, is dominated by intrusive rocks belonging to the c. 1.86-1.65 Ga Transscandinavian Igneous Belt (TIB). However, the site investigation area is situated in between two c. 1.45 Ga old anorogenic granites, the Goetemar granite in the north and the Uthammar granite in the south. This study evaluates the emplacement mechanism of these intrusions and their structural influence on the older bedrock. Field observations and structural measurements indicate that both the Goetemar and the Uthammar granites are discordant and have not imposed any significant ductile deformation on their wall-rocks. The apparent conformity of geological contacts and fabrics in the wall rocks and the southern margin of the Goetemar granite is coincidental and inherited from the pattern of Svecokarelian deformation of the TIB. However, interpretation of regional aeromagnetic data suggests that the granites occur within a broad, NNE-SSW trending linear belt, pointing to deep seated tectonic control on their generation, ascent and emplacement. Thermochronology indicates that the granites were emplaced at depths between 4 and 8 km into brittle wall rocks. The 3-D shape of the Goetemar and Uthammar plutons has been investigated by 2.75D forward modelling of the residual gravity anomalies due to both granites. Both granites are associated with strong residual gravity anomalies of up to -10 mgal. Constraints on the geometry of the plutons at the surface are provided from surface geology maps and several deep boreholes located on or close to the model profiles. A further variable in the gravity modelling is introduced by either allowing the upper contact of the plutons to assume the most suitable orientation to produce the best fit between the modelled and observed gravity ('unconstrained models') or by forcing the near surface orientation of the contacts to be vertical (&apos

  11. Site descriptions for preliminary radiological assessments of low-level waste repositories

    International Nuclear Information System (INIS)

    Burgess, W.E.; Jones, C.H.; Sumerling, T.J.; Ashton, J.

    1988-07-01

    The environmental contexts of four sites, previously under investigation by UK Nirex Ltd. as potential locations for low-level waste disposal facilities, are described. Information on geographical setting, climate, surface hydrology, land use, agriculture, fisheries, geology and hydrogeology is presented. The geological and hydrogeological data are interpreted with the support of deterministic modelling of groundwater conditions. The routes by which radionuclides may migrate from the site are identified and reduced to 1D statistical descriptions suitable for use in probabilistic risk assessments. Additional data required to improve the assessment of the performance of the site are identified. (author)

  12. Human population and activities at Simpevarp. Site description

    International Nuclear Information System (INIS)

    Miliander, Sofia; Punakivi, Mari; Kylaekorpi, Lasse; Rydgren, Bernt

    2004-12-01

    The Swedish Nuclear Fuel and Waste Management Co (SKB) is in the process of selecting a safe and environmentally acceptable location for a deep repository of radioactive waste. Two alternative locations are under investigation. These are Forsmark, Oesthammars kommun (kommun = municipality) and Simpevarp/Laxemar, Oskarshamns kommun. SKB has expressed the importance of describing the humans and their activities in these areas and therefore has this synthesis concerning the human population in Forsmark been produced. The description is a statistical synthesis, mainly based upon statistical data from SCB (Statistics Sweden) that has been collected, processed and analysed. The statistical data has not been verified through site inspections and interviews. When using statistical data, it is advisable to note that the data becomes more unreliable if the areas are small, with small populations. The data in this description is essential for future evaluations of the impact on the environment and its human population (environmental impacts assessments). The data is also important when modelling the potential flows of radio nuclides and calculating the risk of exposure in future safety assessments. The actual area for the study is in this report called 'the Simpevarp area', an area of 127.0 km 2 near Oskarshamn nuclear power plant. The land use in Simpevarp area differs notably from the land use in Kalmar laen. The forest area is far more dominating in Simpevarp area than in Kalmar laen and it represents as much as 89% compared to 63% of the total area. Only 4.4% of the area is arable land compared to 11.6% in Kalmar laen and only 0.3% is of other type (wetlands, bare rock, quarries, pites etc) compared to 15.6% in the county. The main observation is that Simpevarp area is a sparsely populated area located in a relatively lightly populated county. In 2002, the population density was 7.4 inhabitants/km 2 , three times lower than in Kalmar laen. The demography statistics show

  13. Human population and activities at Simpevarp. Site description

    Energy Technology Data Exchange (ETDEWEB)

    Miliander, Sofia; Punakivi, Mari; Kylaekorpi, Lasse; Rydgren, Bernt [SwedPower AB, Stockholm (Sweden)

    2004-12-01

    The Swedish Nuclear Fuel and Waste Management Co (SKB) is in the process of selecting a safe and environmentally acceptable location for a deep repository of radioactive waste. Two alternative locations are under investigation. These are Forsmark, Oesthammars kommun (kommun = municipality) and Simpevarp/Laxemar, Oskarshamns kommun. SKB has expressed the importance of describing the humans and their activities in these areas and therefore has this synthesis concerning the human population in Forsmark been produced. The description is a statistical synthesis, mainly based upon statistical data from SCB (Statistics Sweden) that has been collected, processed and analysed. The statistical data has not been verified through site inspections and interviews. When using statistical data, it is advisable to note that the data becomes more unreliable if the areas are small, with small populations. The data in this description is essential for future evaluations of the impact on the environment and its human population (environmental impacts assessments). The data is also important when modelling the potential flows of radio nuclides and calculating the risk of exposure in future safety assessments. The actual area for the study is in this report called 'the Simpevarp area', an area of 127.0 km{sup 2} near Oskarshamn nuclear power plant. The land use in Simpevarp area differs notably from the land use in Kalmar laen. The forest area is far more dominating in Simpevarp area than in Kalmar laen and it represents as much as 89% compared to 63% of the total area. Only 4.4% of the area is arable land compared to 11.6% in Kalmar laen and only 0.3% is of other type (wetlands, bare rock, quarries, pites etc) compared to 15.6% in the county. The main observation is that Simpevarp area is a sparsely populated area located in a relatively lightly populated county. In 2002, the population density was 7.4 inhabitants/km{sup 2}, three times lower than in Kalmar laen. The

  14. An object model for beamline descriptions

    International Nuclear Information System (INIS)

    Hill, B.W.; Martono, H.; Gillespie, J.S.

    1997-01-01

    Translation of beamline model descriptions between different accelerator codes presents a unique challenge due to the different representations used for various elements and subsystems. These differences range from simple units conversions to more complex translations involving multiple beamline components. A representation of basic accelerator components is being developed in order to define a meta-structure from which beamline models, in different codes, can be described and to facilitate the translation of models between these codes. Sublines of basic components will be used to represent more complex beamline descriptions and bridge the gap between codes which may represent a beamline element as a single entity, and those which use multiple elements to describe the same physical device. A C++ object model for supporting this beamline description and a grammar for describing beamlines in terms of these components is being developed. The object model will support a common graphic user interface and translation filters for representing native beamline descriptions for a variety of accelerator codes. An overview of our work on the object model for beamline descriptions is presented here. copyright 1997 American Institute of Physics

  15. The SocioEconomic Analysis of Repository Siting (SEARS): Technical description: Final draft

    International Nuclear Information System (INIS)

    1984-11-01

    Socioeconomic impacts must be assessed both for the near term and for the future. One means of addressing the need for the assessment of such impacts has been through the development of the computerized socioeconomic assessment model called the SocioEconomic Analysis of Repository Siting (SEARS) model. The SEARS model was developed for the Battelle Project Management Division. It was refined and adapted from state-of-the-art computerized projection models and thoroughly validated and is now available for use in projecting the likely socioeconomic impacts of a repository facility. This Technical Description is one of six major products that describe the SEARS modeling system. 61 refs., 11 figs., 9 tabs

  16. Developing methodology for description of biosphere evolution at Olkiluoto disposal site utilising forest studies at other land uplift sites

    International Nuclear Information System (INIS)

    Ikondn, A.T.K.; Afo, L.

    2004-01-01

    In Finland, Olkiluoto Island has been selected as the site for final disposal of spent nuclear fuel, in addition to the existing repository for low and intermediate level waste. When creating biosphere models for safety assessments, local main features and processes need to be taken into account. A special characteristic of the site, as well as the coastal area of the Gulf of Bothnia in general, is the land uplift (6-9 mm/a). This continuously exposes new land to soil-formation processes and provides surfaces for colonization by plant communities. The forest vegetation succession on stony, fine-grained till soils starts from deciduous shoreline vegetation and ends in almost pure Norway spruce forests. This has enabled to study ecological and microbiological processes in soils and forests of different developmental stages, to monitor forest condition and the factors affecting it in sites locating close to each other. It has also made possible gradient studies of the succession of boreal mire ecosystems without a need to wait thousands of years. Applying a methodology described in the full paper, a descriptive model on the evolution of the biosphere will be established to indicate possible ecosystem distributions and main characteristics on the area on the basis of above-mentioned studies carried out by Finnish Forest Research Institute, and of results of the site investigations at Olkiluoto. In future, the evolution description will be used as a basis for selection of appropriate ecosystem modules and parameter values in the subsequent coupled assessment model systems. (author)

  17. CORECOOL, model description of the programme

    International Nuclear Information System (INIS)

    Andersen, J.G.M.; Abel-Larsen, H.

    1978-11-01

    CORECOOL, Convection and Radiation Emergency Cooling, is a model for the two-phase flow and heat transfer in a fuel element during the core heat-up phase following a loss of coolant accident. The model for the two-phase flow is based on a solution of the conservation equations with a separate description of the two phases and thermodynamic non-equilibrium. The flow-regimes considered are drop flow and film flow. The heat transfer consists of convection, sputtering and radiation heat transfer. The documentation of CORECOOL consists of four parts: I) model description, II) programme description (COMMERCIAL), III) users guide (COMMERCIAL) IV) verification (COMMERCIAL). CORECOOL is a joint project between Risoe National Laboratory Denmark and General Electric Company, San Jose, USA. (author)

  18. Nevada National Security Site Environmental Report 2011 Attachment A: Site Description

    Energy Technology Data Exchange (ETDEWEB)

    Cathy Wills, ed.

    2012-09-12

    This attachment expands on the general description of the Nevada National Security Site (NNSS) presented in the Introduction to the Nevada National Security Site Environmental Report 2011. Included are subsections that summarize the site's geological, hydrological, climatological, and ecological setting and the cultural resources of the NNSS. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NNSS. An adequate knowledge of the site's environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NNSS. The NNSS environment contributes to several key features of the site that afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NNSS operations. These key features include the general remote location of the NNSS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  19. Nevada National Security Site Environmental Report 2011 Attachment A: Site Description

    International Nuclear Information System (INIS)

    Wills, Cathy

    2012-01-01

    This attachment expands on the general description of the Nevada National Security Site (NNSS) presented in the Introduction to the Nevada National Security Site Environmental Report 2011. Included are subsections that summarize the site's geological, hydrological, climatological, and ecological setting and the cultural resources of the NNSS. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NNSS. An adequate knowledge of the site's environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NNSS. The NNSS environment contributes to several key features of the site that afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NNSS operations. These key features include the general remote location of the NNSS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  20. Hanford Site Composite Analysis Technical Approach Description: Hanford Site Disposition Baseline.

    Energy Technology Data Exchange (ETDEWEB)

    Cobb, M. A. [CH2M HILL Plateau Remediation Company, Richland, WA (United States); Dockter, R. E. [CH2M HILL Plateau Remediation Company, Richland, WA (United States)

    2017-10-02

    The permeability of ground surfaces within the U.S. Department of Energy’s (DOE) Hanford Site strongly influences boundary conditions when simulating the movement of groundwater using the Subsurface Transport Over Multiple Phases model. To conduct site-wide modeling of cumulative impacts to groundwater from past, current, and future waste management activities, a site-wide assessment of the permeability of surface conditions is needed. The surface condition of the vast majority of the Hanford Site has been and continues to be native soils vegetated with dryland grasses and shrubs.

  1. Minimum Description Length Shape and Appearance Models

    DEFF Research Database (Denmark)

    Thodberg, Hans Henrik

    2003-01-01

    The Minimum Description Length (MDL) approach to shape modelling is reviewed. It solves the point correspondence problem of selecting points on shapes defined as curves so that the points correspond across a data set. An efficient numerical implementation is presented and made available as open s...

  2. Nevada National Security Site Environmental Report 2012 Attachment A: Site Description

    Energy Technology Data Exchange (ETDEWEB)

    Wills, Cathy A

    2013-09-11

    This attachment expands on the general description of the Nevada National Security Site (NNSS) presented in the Introduction to the Nevada National Security Site Environmental Report 2012 (National Security Technologies, LLC [NSTec], 2013). Included are subsections that summarize the site’s geological, hydrological, climatological, and ecological setting and the cultural resources of the NNSS. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NNSS. An adequate knowledge of the site’s environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NNSS. The NNSS environment contributes to several key features of the site that afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NNSS operations. These key features include the general remote location of the NNSS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  3. Site descriptions of environmental restoration units at the Oak Ridge K-25 Site, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    Goddard, P.L.; Legeay, A.J.; Pesce, D.S.; Stanley, A.M.

    1995-11-01

    This report, Site Descriptions of Environmental Restoration Units at the Oak Ridge K-25 Site, Oak Ridge, Tennessee, is being prepared to assimilate information on sites included in the Environmental Restoration (ER) Program of the K-25 Site, one of three major installations on the Oak Ridge Reservation (ORR) built during World War III as part of the Manhattan Project. The information included in this report will be used to establish program priorities so that resources allotted to the K-25 ER Program can be best used to decrease any risk to humans or the environment, and to determine the sequence in which any remedial activities should be conducted. This document will be updated periodically in both paper and Internet versions. Units within this report are described in individual data sheets arranged alphanumerically. Each data sheet includes entries on project status, unit location, dimensions and capacity, dates operated, present function, lifecycle operation, waste characteristics, site status, media of concern, comments, and references. Each data sheet is accompanied by a photograph of the unit, and each unit is located on one of 13 area maps. These areas, along with the sub-area, unit, and sub-unit breakdowns within them, are outlined in Appendix A. Appendix B is a summary of information on remote aerial sensing and its applicability to the ER program

  4. Site descriptions of environmental restoration units at the Oak Ridge K-25 Site, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    Goddard, P.L.; Legeay, A.J.; Pesce, D.S.; Stanley, A.M.

    1995-11-01

    This report, Site Descriptions of Environmental Restoration Units at the Oak Ridge K-25 Site, Oak Ridge, Tennessee, is being prepared to assimilate information on sites included in the Environmental Restoration (ER) Program of the K-25 Site, one of three major installations on the Oak Ridge Reservation (ORR) built during World War III as part of the Manhattan Project. The information included in this report will be used to establish program priorities so that resources allotted to the K-25 ER Program can be best used to decrease any risk to humans or the environment, and to determine the sequence in which any remedial activities should be conducted. This document will be updated periodically in both paper and Internet versions. Units within this report are described in individual data sheets arranged alphanumerically. Each data sheet includes entries on project status, unit location, dimensions and capacity, dates operated, present function, lifecycle operation, waste characteristics, site status, media of concern, comments, and references. Each data sheet is accompanied by a photograph of the unit, and each unit is located on one of 13 area maps. These areas, along with the sub-area, unit, and sub-unit breakdowns within them, are outlined in Appendix A. Appendix B is a summary of information on remote aerial sensing and its applicability to the ER program.

  5. Nevada National Security Site Environmental Report 2016, Attachment A: Site Description

    Energy Technology Data Exchange (ETDEWEB)

    Wills, Cathy [National Security Technologies, LLC. (NSTec), Mercury, NV (United States)

    2017-09-07

    This attachment expands on the general description of the Nevada National Security Site (NNSS) presented in the Introduction to the Nevada National Security Site Environmental Report 2016 (prepared by National Security Technologies, LLC [NSTec], 2017). Included are subsections that summarize the site’s geological, hydrological, climatological, and ecological settings and the cultural resources of the NNSS. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NNSS. An adequate knowledge of the site’s environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NNSS. The NNSS environment contributes to several key features of the site that afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NNSS operations. These key features include the general remote location of the NNSS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  6. Nevada National Security Site Environmental Report 2013 Attachment A: Site Description

    Energy Technology Data Exchange (ETDEWEB)

    Wills, C.

    2014-09-09

    This attachment expands on the general description of the Nevada National Security Site (NNSS) presented in the Introduction to the Nevada National Security Site Environmental Report 2012 (National Security Technologies, LLC [NSTec], 2013). Included are subsections that summarize the site’s geological, hydrological, climatological, and ecological setting and the cultural resources of the NNSS. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NNSS. An adequate knowledge of the site’s environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NNSS. The NNSS environment contributes to several key features of the site that afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NNSS operations. These key features include the general remote location of the NNSS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  7. Bedrock transport properties. Preliminary site description Simpevarp subarea - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Byegaard, Johan; Gustavsson, Eva [Geosigma AB, Uppsala (Sweden); Tullborg, Eva-Lena [Terralogica AB, Graabo (Sweden); Berglund, Sten [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

    2005-06-01

    This report presents the site descriptive model of transport properties developed as a part of the Simpevarp 1.2 site description. The main parameters included in the model, referred to as retardation parameters, are the matrix porosity and diffusivity, and the matrix sorption coefficient K{sub d}. The model is based on the presently available site investigation data, mainly obtained from laboratory investigations of core samples from boreholes within the Simpevarp subarea, and on data from previous studies at the Aespoe Hard Rock Laboratory (Aespoe HRL). The modelling is a first attempt, based on limited data, to obtain a description of the retardation parameters. Further refinement of the model is foreseen when more data becomes available for future versions of the Simpevarp site description. The modelling work included descriptions of rock mass geology, the fractures and deformation zones, the hydrogeochemistry and also the available results from the site specific porosity, sorption and diffusivity measurements. The description of the transport related aspects of the data and models presented by other modelling disciplines is an important part of the transport description. In accordance with the strategy for the modelling of transport properties, the results are presented as a 'retardation model', in which a summary of the transport data for the different geological compartments is given. Concerning the major rock types, Aevroe granite, quartz monzodiorite and fine-grained dioritoid are identified as the rock types dominating the main rock domains identified and described in the site descriptive model of the bedrock geology. However, relatively large parts of the rock consist of altered rock and the open fracture frequency appears to be correlated to the altered/oxidised parts of the rock. This implies that transport in open fractures to a large extent takes place in the altered parts of the rock. For the fracture mineralogy, it is found that the

  8. Preliminary safety evaluation for the Laxemar subarea. Based on data and site descriptions after the initial site investigation stage

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Johan [JA Streamflow AB, Aelvsjoe (Sweden)

    2006-03-15

    The main objectives of this Preliminary Safety Evaluation (PSE) of the Laxemar subarea have been to determine, with limited efforts, whether the feasibility study's judgement of the suitability of the candidate area with respect to long-term safety holds up in the light of the actual site investigation data; to provide feedback to continued site investigations and site-specific repository design and to identify site-specific scenarios and geoscientific issues for further analyses. The PSE focuses on comparing the attained knowledge of the sites with the suitability criteria as set out by SKB in 2000. These criteria both concern properties of the site judged to be necessary for safety and engineering (requirements) and properties judged to be beneficial (preferences). The findings are then evaluated in order to provide feedback to continued investigations and design work. The PSE does not aim at comparing sites and does not assess compliance with safety and radiation protection criteria. The latter is eventually done in coming Safety Assessments. This preliminary safety evaluation shows that, according to existing data, the Laxemar subarea meets all safety requirements. The evaluation also shows that the Laxemar subarea meets most of the safety preferences, but for some aspects of the site description further reduction of the uncertainties would enhance the safety case. Despite the stated concerns, there is no reason, from a safety point of view, not to continue the Site Investigations at the Laxemar subarea. There are uncertainties to resolve and the safety would eventually need to be verified through a proper safety assessment. Only some of the uncertainties noted in the Site Descriptive Model have safety implications and need further resolution for this reason. Furthermore, uncertainties may need resolving for other reasons, such as giving an adequate assurance of site understanding or assisting in optimising design. Notably, there are questions about the

  9. Preliminary safety evaluation for the Laxemar subarea. Based on data and site descriptions after the initial site investigation stage

    International Nuclear Information System (INIS)

    Andersson, Johan

    2006-03-01

    The main objectives of this Preliminary Safety Evaluation (PSE) of the Laxemar subarea have been to determine, with limited efforts, whether the feasibility study's judgement of the suitability of the candidate area with respect to long-term safety holds up in the light of the actual site investigation data; to provide feedback to continued site investigations and site-specific repository design and to identify site-specific scenarios and geoscientific issues for further analyses. The PSE focuses on comparing the attained knowledge of the sites with the suitability criteria as set out by SKB in 2000. These criteria both concern properties of the site judged to be necessary for safety and engineering (requirements) and properties judged to be beneficial (preferences). The findings are then evaluated in order to provide feedback to continued investigations and design work. The PSE does not aim at comparing sites and does not assess compliance with safety and radiation protection criteria. The latter is eventually done in coming Safety Assessments. This preliminary safety evaluation shows that, according to existing data, the Laxemar subarea meets all safety requirements. The evaluation also shows that the Laxemar subarea meets most of the safety preferences, but for some aspects of the site description further reduction of the uncertainties would enhance the safety case. Despite the stated concerns, there is no reason, from a safety point of view, not to continue the Site Investigations at the Laxemar subarea. There are uncertainties to resolve and the safety would eventually need to be verified through a proper safety assessment. Only some of the uncertainties noted in the Site Descriptive Model have safety implications and need further resolution for this reason. Furthermore, uncertainties may need resolving for other reasons, such as giving an adequate assurance of site understanding or assisting in optimising design. Notably, there are questions about the

  10. Description of climate, surface hydrology, and near-surface hydrogeology. Preliminary site description. Forsmark area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Johansson, Per-Olof [Artesia Grundvattenkonsult AB, Stockholm (Sweden); Werner, Kent [SWECO VIAK AB/Golder Associates AB, Stockholm (Sweden); Bosson, Emma; Berglund, Sten [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Juston, John [DBE Sweden, Uppsala (Sweden)

    2005-06-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is conducting site investigations at two different locations, the Forsmark and Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. The results from the investigations at the sites are used as a basic input to the development of Site Descriptive Models (SDM). The SDM shall summarise the current state of knowledge of the site, and provide parameters and models to be used in further analyses within Safety Assessment, Repository Design and Environmental Impact Assessment. The present report is a background report describing the meteorological conditions and the modelling of surface hydrology and near-surface hydrogeology in support of the Forsmark version 1.2 SDM based on the data available in the Forsmark 1.2 'data freeze' (July 31, 2004). The groundwater is very shallow, with groundwater levels within one meter below ground as an annual mean for almost all groundwater monitoring wells. Also, the annual groundwater level amplitude is less than 1.5 m for most wells. The shallow groundwater levels mean that there is a strong interaction between evapotranspiration, soil moisture and groundwater. In the modelling, surface water and near-surface groundwater divides are assumed to coincide. The small-scale topography implies that many local, shallow groundwater flow systems are formed in the Quaternary deposits, overlaying more large-scale flow systems associated with groundwater flows at greater depths. Groundwater level time series from wells in till and bedrock within the same areas show a considerably higher groundwater level in the till than in the bedrock. The observed differences in levels are not fully consistent with the good hydraulic contact between overburden and bedrock indicated by the hydraulic tests in the Quaternary deposits. However, the relatively lower groundwater levels in the bedrock may be caused by the horizontal to sub-horizontal highly

  11. Description, Modelling and Design of Production Systems

    DEFF Research Database (Denmark)

    Jacobsen, Peter; Rudolph, Carsten

    1997-01-01

    Design of production systems are rarely an activity in which decision makers in most production companies have much experience. In future, this activity is to be more recurrent due to more and more frequent changes in the production task. Consequently, the decision makers are in need of better...... management tools and methods for description and modelling of production systems supporting the decisions. In this article a structural framework to describe and model production systems will be introduced, and it is shown how the production system of a minor Danish manufacturer of electromechanical...

  12. Hydrogeological pre-modelling exercises. Assessment of impact of the Aespoe Hard Rock Laboratory. Sensitivities of palaeo-hydrogeology. Development of a local near-surface Hydro-DFN for KLX09B-F. Site descriptive modelling SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Hartley, Lee; Jackson, Peter; Joyce, Steve; Roberts, David; Shevelan, John; Swift, Ben; Gylling, Bjoern; Marsic, Niko; Hermanson, Jan; Oehman, Johan

    2007-12-01

    Numerical modelling has been used to investigate the potential impact of the Aespoe HRL on regional groundwater flow and hydro-geochemistry in the Laxemar study area. The numerical models have been adapted for this application from the ones use in the site-descriptive modelling (SDM) and SR-Can assessment modelling based on Laxemar version 1.2. In order to test the robustness of the simulation results, sensitivities were studied with respect to different flow boundary conditions and the hydraulic properties of the Quaternary deposits, particularly those beneath the sea around the Aespoe island. The simulations show that the Aespoe HRL has a local effect on the groundwater situation. Typically, in the simulations, the rock under the Aespoe island, the bays around it and the Aevroe area (mainly western part of the islands of Aevroe, Mjaelen and Haaloe) are influenced. In the sensitivity study, visualisations of the drawdown caused by the HRL tunnel system show small differences in the results for head versus flux top boundary conditions, little sensitivity to a change in the surface infiltration rate, but most sensitivity to the contact between the sea and the bedrock beneath the seabed sediments. For all simulation cases considered, results suggest that the Aespoe HRL has not been in operation sufficiently long to have affected the chemistry of samples collected at Laxemar and Simpevarp, though there is some possibility that Aevroe samples have been altered, at least for boreholes in the western part of Aevroe, Mjaelen and Haaloe. The distribution of flow and discharge areas around the bay at Aespoe is clearly affected by the HRL for all cases. Using the drawdown in percussion drilled boreholes around Aespoe as an interference test suggests that there is a partial reduction in the hydraulic contact between the sea and the groundwater system in the bedrock beneath. It is recommended that the conclusions about appropriate hydraulic properties for Quaternary sediments

  13. Hydrogeological pre-modelling exercises. Assessment of impact of the Aespoe Hard Rock Laboratory. Sensitivities of palaeo-hydrogeology. Development of a local near-surface Hydro-DFN for KLX09B-F. Site descriptive modelling SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, Lee; Jackson, Peter; Joyce, Steve; Roberts, David; Shevelan, John; Swift, Ben (Serco Assurance, Harwell (GB)); Gylling, Bjoern; Marsic, Niko (Kemakta Konsult AB, Stockholm (SE)); Hermanson, Jan; Oehman, Johan (Golders Associates (SE))

    2007-12-15

    Numerical modelling has been used to investigate the potential impact of the Aespoe HRL on regional groundwater flow and hydro-geochemistry in the Laxemar study area. The numerical models have been adapted for this application from the ones use in the site-descriptive modelling (SDM) and SR-Can assessment modelling based on Laxemar version 1.2. In order to test the robustness of the simulation results, sensitivities were studied with respect to different flow boundary conditions and the hydraulic properties of the Quaternary deposits, particularly those beneath the sea around the Aespoe island. The simulations show that the Aespoe HRL has a local effect on the groundwater situation. Typically, in the simulations, the rock under the Aespoe island, the bays around it and the Aevroe area (mainly western part of the islands of Aevroe, Mjaelen and Haaloe) are influenced. In the sensitivity study, visualisations of the drawdown caused by the HRL tunnel system show small differences in the results for head versus flux top boundary conditions, little sensitivity to a change in the surface infiltration rate, but most sensitivity to the contact between the sea and the bedrock beneath the seabed sediments. For all simulation cases considered, results suggest that the Aespoe HRL has not been in operation sufficiently long to have affected the chemistry of samples collected at Laxemar and Simpevarp, though there is some possibility that Aevroe samples have been altered, at least for boreholes in the western part of Aevroe, Mjaelen and Haaloe. The distribution of flow and discharge areas around the bay at Aespoe is clearly affected by the HRL for all cases. Using the drawdown in percussion drilled boreholes around Aespoe as an interference test suggests that there is a partial reduction in the hydraulic contact between the sea and the groundwater system in the bedrock beneath. It is recommended that the conclusions about appropriate hydraulic properties for Quaternary sediments

  14. Description of the Formerly Utilized Sites Remedial Action Program

    International Nuclear Information System (INIS)

    1980-09-01

    The background and the results to date of the Department of Energy program to identify and evaluate the radiological conditions at sites formerly utilized by the Corps of Engineers' Manhattan Engineer District (MED) and the US Atomic Energy Commission (AEC) are summarized. The sites of concern were federally, privately, and institutionally owned and were used primarily for research, processing, and storage of uranium and thorium ores, concentrates, or residues. Some sites were subsequently released for other purposes without radiological restriction. Surveys have been conducted since 1974 to document radiological conditions at such sites. Based on radiological surveys, sites are identified in this document that require, or are projected to require, remedial action to remove potential restrictions on the use of the property due to the presence of residual low-level radioactive contamination. Specific recommendations for each site will result from more detailed environmental and engineering surveys to be conducted at those sites and, if necessary, an environmental impact assessment or environmental impact statement will be prepared. Section 3.0 describes the current standards and guidelines now being used to conduct remedial actions. Current authority of the US Department of Energy (DOE) to proceed with remedial actions and the new authority required are summarized. A plan to implement the Formerly Utilized Sites Remedial Action Program (FUSRAP) in accordance with the new authority is presented, including the objectives, scope, general approach, and a summary schedule. Key issues affecting schedule and cost are discussed

  15. Description of the Formerly Utilized Sites Remedial Action Program

    Energy Technology Data Exchange (ETDEWEB)

    1980-09-01

    The background and the results to date of the Department of Energy program to identify and evaluate the radiological conditions at sites formerly utilized by the Corps of Engineers' Manhattan Engineer District (MED) and the US Atomic Energy Commission (AEC) are summarized. The sites of concern were federally, privately, and institutionally owned and were used primarily for research, processing, and storage of uranium and thorium ores, concentrates, or residues. Some sites were subsequently released for other purposes without radiological restriction. Surveys have been conducted since 1974 to document radiological conditions at such sites. Based on radiological surveys, sites are identified in this document that require, or are projected to require, remedial action to remove potential restrictions on the use of the property due to the presence of residual low-level radioactive contamination. Specific recommendations for each site will result from more detailed environmental and engineering surveys to be conducted at those sites and, if necessary, an environmental impact assessment or environmental impact statement will be prepared. Section 3.0 describes the current standards and guidelines now being used to conduct remedial actions. Current authority of the US Department of Energy (DOE) to proceed with remedial actions and the new authority required are summarized. A plan to implement the Formerly Utilized Sites Remedial Action Program (FUSRAP) in accordance with the new authority is presented, including the objectives, scope, general approach, and a summary schedule. Key issues affecting schedule and cost are discussed.

  16. Description of climate, surface hydrology, and near-surface hydrogeology. Preliminary site description. Forsmark area - version 1.2

    International Nuclear Information System (INIS)

    Johansson, Per-Olof; Werner, Kent; Bosson, Emma; Berglund, Sten; Juston, John

    2005-06-01

    chloride content has been found below Lake Bolundsfjaerden, Lake Eckarfjaerden and Lake Gaellsbotraesket. The relations between the sea water level and the water levels in Lake Norra Bassaengen, Lake Bolundsfjaerden and Lake Lillfjaerden show that inflow of sea water can occur during periods of high sea water levels. The results from the hydrological GIS modelling support the assumptions and conclusions in the descriptive model. The flow model is highly sensitive to the topography, as this is the only parameter determining the flow pattern. Consequently, the simulated locations of recharge and discharge areas are strongly influenced by the local topography. In addition, the flat topography implies that small errors in the topographical model (the Digital Elevation Model, DEM) may have large effects on the modelled flow pattern. Ditches, diverted water courses and other human impacts on the system are important in some parts of the model area. These and other types of ''man-made structures'' are not fully considered in the DEM. The water balance for the Forsmark area, as calculated with the MIKE SHE modelling tool, agrees with the presented conceptual and descriptive models of the flow system. The transient model simulations for the selected reference year (1988) result in an annual total runoff of 226 mm and a total actual evapotranspiration of 441 mm. These values, which are average values for the considered model area, are considered to be reasonable for the Forsmark area. At present, however, they cannot be tested against site-specific measurements. The MIKE SHE model produces a shallow groundwater table, which approximately agrees with the groundwater level measurements within the area, and with the overall conceptualisation of the system. However, no detailed model calibration has been performed. The modelling results show that most of the groundwater flow occurs in the Quaternary deposits. The results also illustrate the importance of the fracture zones for the

  17. Modelling Imprecise Arguments in Description Logic

    Directory of Open Access Journals (Sweden)

    LETIA, I. A.

    2009-10-01

    Full Text Available Real arguments are a mixture of fuzzy linguistic variables and ontological knowledge. This paper focuses on modelling imprecise arguments in order to obtain a better interleaving of human and software agents argumentation, which might be proved useful for extending the number of real life argumentative-based applications. We propose Fuzzy Description Logic as the adequate technical instrumentation for filling the gap between human arguments and software agents arguments. A proof of concept scenario has been tested with the fuzzyDL reasoner.

  18. Description of floodplains and wetlands, Deaf Smith County site, Texas

    International Nuclear Information System (INIS)

    1986-11-01

    Floodplains and wetlands are important features of the Texas Panhandle landscape, and are found on the Deaf Smith County site and in its vicinity. Use or disturbance of floodplains and wetlands in relation to the Civilian Radioactive Waste Management Program is subject to environmental review requirements implementing two Executive Orders. This report provides general information on playa wetlands in the Texas Panhandle, and describes and maps floodplains and wetlands on the Deaf Smith site and in its vicinity. The report is based on the published literature, with information from limited field reconnaissance included

  19. Description of mathematical models and computer programs

    International Nuclear Information System (INIS)

    1977-01-01

    The paper gives a description of mathematical models and computer programs for analysing possible strategies for spent fuel management, with emphasis on economic analysis. The computer programs developed, describe the material flows, facility construction schedules, capital investment schedules and operating costs for the facilities used in managing the spent fuel. The computer programs use a combination of simulation and optimization procedures for the economic analyses. Many of the fuel cycle steps (such as spent fuel discharges, storage at the reactor, and transport to the RFCC) are described in physical and economic terms through simulation modeling, while others (such as reprocessing plant size and commissioning schedules, interim storage facility commissioning schedules etc.) are subjected to economic optimization procedures to determine the approximate lowest-cost plans from among the available feasible alternatives

  20. Regional hydrogeological simulations using CONECTFLOW. Preliminary site description. Laxemar sub area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, Lee; Hunter, Fiona; Jackson, Peter; McCarthy, Rachel [Serco Assurance, Risley (United Kingdom); Gylling, Bjoern; Marsic, Niko [Kemakta Konsult AB, Stockholm (Sweden)

    2006-04-15

    The main objective of this study is to support the development of a preliminary Site Description of the Laxemar subarea on a regional-scale based on the available data of November 2004 (Data Freeze L1.2). A more specific objective of this study is to assess the role of both known and less quantified hydrogeological conditions in determining the present-day distribution of saline groundwater in the Laxemar subarea on a regional-scale. An improved understanding of the palaeo-hydrogeology is necessary in order to gain credibility for the Site Description in general and the hydrogeological description in particular. This is to serve as a basis for describing the present hydrogeological conditions on a local-scale, as well as predictions of future hydrogeological conditions. Another objective is to assess the flow-paths from the local-scale model domain, based on the present-day flow conditions, to assess the distribution of discharge and recharge areas connected to the flow at the approximate repository depth to inform the Preliminary Safety Evaluation. Significant new features incorporated in the modelling include: a depth variation in hydraulic properties within the deformation zones; a dependence on rock domain and depth in the rock mass properties in regional-scale models; a more detailed model of the overburden in terms of a layered system of spatially variable thickness made up of several different types of Quaternary deposits has been implemented; and several variants on the position of the watertable have been tried. The motivation for introducing a dependence on rock domain was guided by the hydrogeological interpretation with the aim of honouring the observed differences in hydraulic properties measured at the boreholes.

  1. Regional hydrogeological simulations using CONECTFLOW. Preliminary site description. Laxemar sub area - version 1.2

    International Nuclear Information System (INIS)

    Hartley, Lee; Hunter, Fiona; Jackson, Peter; McCarthy, Rachel; Gylling, Bjoern; Marsic, Niko

    2006-04-01

    The main objective of this study is to support the development of a preliminary Site Description of the Laxemar subarea on a regional-scale based on the available data of November 2004 (Data Freeze L1.2). A more specific objective of this study is to assess the role of both known and less quantified hydrogeological conditions in determining the present-day distribution of saline groundwater in the Laxemar subarea on a regional-scale. An improved understanding of the palaeo-hydrogeology is necessary in order to gain credibility for the Site Description in general and the hydrogeological description in particular. This is to serve as a basis for describing the present hydrogeological conditions on a local-scale, as well as predictions of future hydrogeological conditions. Another objective is to assess the flow-paths from the local-scale model domain, based on the present-day flow conditions, to assess the distribution of discharge and recharge areas connected to the flow at the approximate repository depth to inform the Preliminary Safety Evaluation. Significant new features incorporated in the modelling include: a depth variation in hydraulic properties within the deformation zones; a dependence on rock domain and depth in the rock mass properties in regional-scale models; a more detailed model of the overburden in terms of a layered system of spatially variable thickness made up of several different types of Quaternary deposits has been implemented; and several variants on the position of the watertable have been tried. The motivation for introducing a dependence on rock domain was guided by the hydrogeological interpretation with the aim of honouring the observed differences in hydraulic properties measured at the boreholes

  2. Standarized input for Hanford environmental impact statements. Part II: site description

    International Nuclear Information System (INIS)

    Jamison, J.D.

    1982-07-01

    Information is presented under the following section headings: summary description; location and physiography; geology; seismology; hydrology; meteorology; ecology; demography and land use; and radiological condition. Five appendixes are included on the 100N, 200 east, 200 west, 300, and 400 areas. This report is intended to provide a description of the Hanford Site against which the environmental impacts of new projects at Hanford can be assessed. It is expected that the summary description amplified with material from the appropriate appendix, will serve as the basic site description section of environmental impact statements prepared to address the requirements of the National Environmental Policy Act

  3. Standarized input for Hanford environmental impact statements. Part II: site description

    Energy Technology Data Exchange (ETDEWEB)

    Jamison, J.D.

    1982-07-01

    Information is presented under the following section headings: summary description; location and physiography; geology; seismology; hydrology; meteorology; ecology; demography and land use; and radiological condition. Five appendixes are included on the 100N, 200 east, 200 west, 300, and 400 areas. This report is intended to provide a description of the Hanford Site against which the environmental impacts of new projects at Hanford can be assessed. It is expected that the summary description amplified with material from the appropriate appendix, will serve as the basic site description section of environmental impact statements prepared to address the requirements of the National Environmental Policy Act (NEPA).

  4. International Nuclear Model. Volume 3. Program description

    International Nuclear Information System (INIS)

    Andress, D.

    1985-01-01

    This is Volume 3 of three volumes of documentation of the International Nuclear Model (INM). This volume presents the Program Description of the International Nuclear Model, which was developed for the Nuclear and Alternate Fuels Division (NAFD), Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), US Department of Energy (DOE). The International Nuclear Model (INM) is a comprehensive model of the commercial nuclear power industry. It simulates economic decisions for reactor deployment and fuel management decision based on an input set of technical economic and scenario parameters. The technical parameters include reactor operating characteristics, fuel cycle timing and mass loss factors, and enrichment tails assays. Economic parameters include fuel cycle costs, financial data, and tax alternatives. INM has a broad range of scenario options covering, for example, process constraints, interregional activities, reprocessing, and fuel management selection. INM reports reactor deployment schedules, electricity generation, and fuel cycle requirements and costs. It also has specialized reports for extended burnup and permanent disposal. Companion volumes to Volume 3 are: Volume 1 - Model Overview, and Volume 2 - Data Base Relationships

  5. SITE GENERATED RADIOLOGICAL WASTE HANDLING SYSTEM DESCRIPTION DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    S. C. Khamankar

    2000-06-20

    The Site Generated Radiological Waste Handling System handles radioactive waste products that are generated at the geologic repository operations area. The waste is collected, treated if required, packaged for shipment, and shipped to a disposal site. Waste streams include low-level waste (LLW) in solid and liquid forms, as-well-as mixed waste that contains hazardous and radioactive constituents. Liquid LLW is segregated into two streams, non-recyclable and recyclable. The non-recyclable stream may contain detergents or other non-hazardous cleaning agents and is packaged for shipment. The recyclable stream is treated to recycle a large portion of the water while the remaining concentrated waste is packaged for shipment; this greatly reduces the volume of waste requiring disposal. There will be no liquid LLW discharge. Solid LLW consists of wet solids such as ion exchange resins and filter cartridges, as-well-as dry active waste such as tools, protective clothing, and poly bags. Solids will be sorted, volume reduced, and packaged for shipment. The generation of mixed waste at the Monitored Geologic Repository (MGR) is not planned; however, if it does come into existence, it will be collected and packaged for disposal at its point of occurrence, temporarily staged, then shipped to government-approved off-site facilities for disposal. The Site Generated Radiological Waste Handling System has equipment located in both the Waste Treatment Building (WTB) and in the Waste Handling Building (WHB). All types of liquid and solid LLW are processed in the WTB, while wet solid waste from the Pool Water Treatment and Cooling System is packaged where received in the WHB. There is no installed hardware for mixed waste. The Site Generated Radiological Waste Handling System receives waste from locations where water is used for decontamination functions. In most cases the water is piped back to the WTB for processing. The WTB and WHB provide staging areas for storing and shipping LLW

  6. SITE GENERATED RADIOLOGICAL WASTE HANDLING SYSTEM DESCRIPTION DOCUMENT

    International Nuclear Information System (INIS)

    S. C. Khamankar

    2000-01-01

    The Site Generated Radiological Waste Handling System handles radioactive waste products that are generated at the geologic repository operations area. The waste is collected, treated if required, packaged for shipment, and shipped to a disposal site. Waste streams include low-level waste (LLW) in solid and liquid forms, as-well-as mixed waste that contains hazardous and radioactive constituents. Liquid LLW is segregated into two streams, non-recyclable and recyclable. The non-recyclable stream may contain detergents or other non-hazardous cleaning agents and is packaged for shipment. The recyclable stream is treated to recycle a large portion of the water while the remaining concentrated waste is packaged for shipment; this greatly reduces the volume of waste requiring disposal. There will be no liquid LLW discharge. Solid LLW consists of wet solids such as ion exchange resins and filter cartridges, as-well-as dry active waste such as tools, protective clothing, and poly bags. Solids will be sorted, volume reduced, and packaged for shipment. The generation of mixed waste at the Monitored Geologic Repository (MGR) is not planned; however, if it does come into existence, it will be collected and packaged for disposal at its point of occurrence, temporarily staged, then shipped to government-approved off-site facilities for disposal. The Site Generated Radiological Waste Handling System has equipment located in both the Waste Treatment Building (WTB) and in the Waste Handling Building (WHB). All types of liquid and solid LLW are processed in the WTB, while wet solid waste from the Pool Water Treatment and Cooling System is packaged where received in the WHB. There is no installed hardware for mixed waste. The Site Generated Radiological Waste Handling System receives waste from locations where water is used for decontamination functions. In most cases the water is piped back to the WTB for processing. The WTB and WHB provide staging areas for storing and shipping LLW

  7. Site Closure Strategy Model for Creosote Site

    International Nuclear Information System (INIS)

    Coll, F.R.; Gray, D.R.

    2009-01-01

    In conjunction with RCRA site corrective action at an active wood preserving facility, a risk-based site closure strategy was developed and incorporated the performance of a dense non-aqueous phase liquid (DNAPL) source recovery remedy, a monitored natural attenuation (MNA) remedy for dissolved phase groundwater, and institutional controls. Innovative creosote DNAPL source recovery has been undertaken at the Site since 1998. Pooled creosote DNAPL is present 90 feet below ground within a transmissive sand and gravel aquifer with a saturated thickness of approximately 80 feet. The creosote DNAPL source is situated on the property boundary of the site and has generated a 1/2 mile off-site dissolved phase plume, creating significant NAPL management and remedial technology verification issues. To date, over 120,000 gallons of creosote DNAPL have been recovered from the subsurface utilizing a modified circulation well technology. A mass discharge flux protocol was developed to serve as a major performance metrics for the continuation of source removal efforts and to support the application of monitored natural attenuation as an associated remedial technology for groundwater. The mass removal success has supported the MNA remedy for dissolved phase groundwater and the associated development of institutional controls. The enacted site management strategy outlines the current and future risk management activities for the Site and represents an appropriate site closure strategy for the Site. (authors)

  8. Hanford Site Composite Analysis Technical Approach Description: Groundwater

    Energy Technology Data Exchange (ETDEWEB)

    Budge, T. J. [CH2M HILL Plateau Remediation Company, Richland, WA (United States)

    2017-10-02

    The groundwater facet of the revised CA is responsible for generating predicted contaminant concentration values over the entire analysis spatial and temporal domain. These estimates will be used as part of the groundwater pathway dose calculation facet to estimate dose for exposure scenarios. Based on the analysis of existing models and available information, the P2R Model was selected as the numerical simulator to provide these estimates over the 10,000-year temporal domain of the CA. The P2R Model will use inputs from initial plume distributions, updated for a start date of 1/1/2017, and inputs from the vadose zone facet, created by a tool under development as part of the ICF, to produce estimates of hydraulic head, transmissivity, and contaminant concentration over time. A recommendation of acquiring 12 computer processors and 2 TB of hard drive space is made to ensure that the work can be completed within the anticipated schedule of the revised CA.

  9. Description of the Northwest hazardous waste site data base and preliminary analysis of site characteristics

    International Nuclear Information System (INIS)

    Woodruff, D.L.; Hartz, K.E.; Triplett, M.B.

    1988-08-01

    The Northwest Hazardous Waste RD and D Center (the Center) conducts research, development, and demonstration (RD and D) activities for hazardous and radioactive mixed-waste technologies applicable to remediating sites in the states of Idaho, Montana, Oregon, and Washington. To properly set priorities for these RD and D activities and to target development efforts it is necessary to understand the nature of the sites requiring remediation. A data base of hazardous waste site characteristics has been constructed to facilitate this analysis. The data base used data from EPA's Region X Comprehensive Environmental Response, Compensation, and Liability Information System (CERCLIS) and from Preliminary Assessment/Site Investigation (PA/SI) forms for sites in Montana. The Center's data base focuses on two sets of sites--those on the National Priorities List (NPL) and other sites that are denoted as ''active'' CERCLIS sites. Active CERCLIS sites are those sites that are undergoing active investigation and analysis. The data base contains information for each site covering site identification and location, type of industry associated with the site, waste categories present (e.g., heavy metals, pesticides, etc.), methods of disposal (e.g., tanks, drums, land, etc.), waste forms (e.g., liquid, solid, etc.), and hazard targets (e.g., surface water, groundwater, etc.). As part of this analysis, the Northwest region was divided into three geographic subregions to identify differences in disposal site characteristics within the Northwest. 2 refs., 18 figs., 5 tabs

  10. Site and Regional Data for Biosphere Assessment BSA-2009 Supplement to Olkiluoto Biosphere Description 2009

    International Nuclear Information System (INIS)

    Aro, L.; Haapanen, R.; Puhakka, L.; Hjerpe, T.; Kirkkala, T.; Koivunen, S.; Lahdenperae, A.-M.; Salo, T.; Ikonen, A.T.K.; Helin, J.

    2010-06-01

    The safety case for a spent nuclear fuel repository at Olkiluoto includes a computational safety assessment. A site-specific biosphere assessment is an integral part of them both. In 2009 an assessment was conducted to demonstrate preparedness to apply for construction license to the repository in 2012. As a part of the biosphere assessment, the present conditions at the site are described in Olkiluoto biosphere description report for an analogue of the future conditions being simulated in the safety assessment. This report is a supplement to the biosphere description report of 2009 and documents the site and regional data used in the biosphere assessment 'BSA-2009' with respective rationales. (orig.)

  11. Hydrogeochemical evaluation. Preliminary site description Laxemar subarea - version 1.2

    International Nuclear Information System (INIS)

    Laaksoharju, Marcus

    2006-04-01

    groups of groundwaters have been identified. Characterisation of pore water in core samples from the Laxemar borehole, KLX03, shows that chemical and isotopic pore water signatures have a characteristic variation of groundwater composition with rock type and depth that is in close agreement with the general trends in hydrochemistry of the adjacent formation (fracture) groundwaters. There is little apparent evidence of a glacial melt signature in the pore waters. Pore waters at depth show an affinity with deep brine evolution. Steady state conditions between pore water and formation groundwaters in the fractures are essentially only developed in the shallow zone of the Aevroe granite, while at depths greater than 450 m the chemical and isotopic composition of the pore water differs markedly from that of the fracture groundwaters in fractures. Diffusion between rock pore water and adjacent fracture groundwaters is identified as the dominant transport process; calculated diffusion coefficients agree well with current knowledge of conditions in the Laxemar site. In this report the models and the site understanding have been consolidated. Despite relatively few new data from depth, the models have been updated and the further understanding gained of groundwater origin, groundwater evolution, reactions, studies of interaction between shallow and deep groundwater, pore water composition in bedrock, microbial depth variation, uncertainties of the mixing calculations, tritium variations with time and 3D visualisation of the spatial variability of groundwater properties. An updated Hydrogeochemical Site Descriptive Model version 1.2 for Laxemar subarea has evolved. The resulting description has improved compared with the 1.2 version for Simpevarp subarea by producing a more detailed process modelling, uncertainty analysis and 3D visualisation. The microbial characterisation gives direct support to, for example, the redox modelling. The coupled transport modelling can address

  12. Hydrogeochemical evaluation. Preliminary site description Laxemar subarea - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Laaksoharju, Marcus (ed.) [Geopoint AB, Stockholm (Sweden)

    2006-04-15

    hydrochemical groups of groundwaters have been identified. Characterisation of pore water in core samples from the Laxemar borehole, KLX03, shows that chemical and isotopic pore water signatures have a characteristic variation of groundwater composition with rock type and depth that is in close agreement with the general trends in hydrochemistry of the adjacent formation (fracture) groundwaters. There is little apparent evidence of a glacial melt signature in the pore waters. Pore waters at depth show an affinity with deep brine evolution. Steady state conditions between pore water and formation groundwaters in the fractures are essentially only developed in the shallow zone of the Aevroe granite, while at depths greater than 450 m the chemical and isotopic composition of the pore water differs markedly from that of the fracture groundwaters in fractures. Diffusion between rock pore water and adjacent fracture groundwaters is identified as the dominant transport process; calculated diffusion coefficients agree well with current knowledge of conditions in the Laxemar site. In this report the models and the site understanding have been consolidated. Despite relatively few new data from depth, the models have been updated and the further understanding gained of groundwater origin, groundwater evolution, reactions, studies of interaction between shallow and deep groundwater, pore water composition in bedrock, microbial depth variation, uncertainties of the mixing calculations, tritium variations with time and 3D visualisation of the spatial variability of groundwater properties. An updated Hydrogeochemical Site Descriptive Model version 1.2 for Laxemar subarea has evolved. The resulting description has improved compared with the 1.2 version for Simpevarp subarea by producing a more detailed process modelling, uncertainty analysis and 3D visualisation. The microbial characterisation gives direct support to, for example, the redox modelling. The coupled transport modelling can

  13. Integrated Site Model Process Model Report

    International Nuclear Information System (INIS)

    Booth, T.

    2000-01-01

    The Integrated Site Model (ISM) provides a framework for discussing the geologic features and properties of Yucca Mountain, which is being evaluated as a potential site for a geologic repository for the disposal of nuclear waste. The ISM is important to the evaluation of the site because it provides 3-D portrayals of site geologic, rock property, and mineralogic characteristics and their spatial variabilities. The ISM is not a single discrete model; rather, it is a set of static representations that provide three-dimensional (3-D), computer representations of site geology, selected hydrologic and rock properties, and mineralogic-characteristics data. These representations are manifested in three separate model components of the ISM: the Geologic Framework Model (GFM), the Rock Properties Model (RPM), and the Mineralogic Model (MM). The GFM provides a representation of the 3-D stratigraphy and geologic structure. Based on the framework provided by the GFM, the RPM and MM provide spatial simulations of the rock and hydrologic properties, and mineralogy, respectively. Functional summaries of the component models and their respective output are provided in Section 1.4. Each of the component models of the ISM considers different specific aspects of the site geologic setting. Each model was developed using unique methodologies and inputs, and the determination of the modeled units for each of the components is dependent on the requirements of that component. Therefore, while the ISM represents the integration of the rock properties and mineralogy into a geologic framework, the discussion of ISM construction and results is most appropriately presented in terms of the three separate components. This Process Model Report (PMR) summarizes the individual component models of the ISM (the GFM, RPM, and MM) and describes how the three components are constructed and combined to form the ISM

  14. Nevada Test Site Environmental Report 2006 and Site Description (Volume 1)

    Energy Technology Data Exchange (ETDEWEB)

    Cathy Wills

    2007-10-01

    The Nevada Test Site Environmental Report 2006 (NTSER) was prepared to meet the information needs of the public and the requirements and guidelines of the U.S. Department of Energy (DOE) for annual site environmental reports. It was prepared by National Security Technologies, LLC (NSTec). This Executive Summary presents the purpose of the document, the major programs conducted at the Nevada Test Site (NTS), NTS key environmental initiatives, radiological releases and potential doses to the public resulting from site operations, a summary of nonradiological releases, implementation status of the NTS Environmental Management System, a summary of compliance with environmental regulations, pollution prevention and waste minimization accomplishments, and significant environmental accomplishments. Much of the content of this Executive Summary is also presented in a separate stand-alone pamphlet titled Nevada Test Site Environmental Report Summary 2006 produced to be a more cost-effective means of distributing information contained in the NTSER to interested DOE stakeholders.

  15. Nevada Test Site Environmental Report 2006 and Site Description (Volume 1)

    International Nuclear Information System (INIS)

    Cathy Wills

    2007-01-01

    The Nevada Test Site Environmental Report 2006 (NTSER) was prepared to meet the information needs of the public and the requirements and guidelines of the U.S. Department of Energy (DOE) for annual site environmental reports. It was prepared by National Security Technologies, LLC (NSTec). This Executive Summary presents the purpose of the document, the major programs conducted at the Nevada Test Site (NTS), NTS key environmental initiatives, radiological releases and potential doses to the public resulting from site operations, a summary of nonradiological releases, implementation status of the NTS Environmental Management System, a summary of compliance with environmental regulations, pollution prevention and waste minimization accomplishments, and significant environmental accomplishments. Much of the content of this Executive Summary is also presented in a separate stand-alone pamphlet titled Nevada Test Site Environmental Report Summary 2006 produced to be a more cost-effective means of distributing information contained in the NTSER to interested DOE stakeholders

  16. Hanford Site Composite Analysis Technical Approach Description: Radionuclide Inventory and Waste Site Selection Process.

    Energy Technology Data Exchange (ETDEWEB)

    Nichols, Will E.; Mehta, Sunil

    2017-09-13

    The updated Hanford Site Composite Analysis will provide an all-pathways dose projection to a hypothetical future member of the public from all planned low-level radioactive waste disposal facilities and potential contributions from all other projected end-state sources of radioactive material left at Hanford following site closure. Its primary purpose is to support the decision-making process of the U.S. Department of Energy (DOE) under DOE O 435.1-1, Radioactive Waste Management (DOE, 2001), related to managing low-level waste disposal facilities at the Hanford Site.

  17. Simple Parametric Model for Airfoil Shape Description

    Science.gov (United States)

    Ziemkiewicz, David

    2017-12-01

    We show a simple, analytic equation describing a class of two-dimensional shapes well suited for representation of aircraft airfoil profiles. Our goal was to create a description characterized by a small number of parameters with easily understandable meaning, providing a tool to alter the shape with optimization procedures as well as manual tweaks by the designer. The generated shapes are well suited for numerical analysis with 2D flow solving software such as XFOIL.

  18. DSEM, Radioactive Waste Disposal Site Economic Model

    International Nuclear Information System (INIS)

    Smith, P.R.

    2005-01-01

    1 - Description of program or function: The Disposal Site Economic Model calculates the average generator price, or average price per cubic foot charged by a disposal facility to a waste generator, one measure of comparing the economic attractiveness of different waste disposal site and disposal technology combinations. The generator price is calculated to recover all costs necessary to develop, construct, operate, close, and care for a site through the end of the institutional care period and to provide the necessary financial returns to the site developer and lender (when used). Six alternative disposal technologies, based on either private or public financing, can be considered - shallow land disposal, intermediate depth disposal, above or below ground vaults, modular concrete canister disposal, and earth mounded concrete bunkers - based on either private or public development. 2 - Method of solution: The economic models incorporate default cost data from the Conceptual Design Report (DOE/LLW-60T, June 1987), a study by Rodgers Associates Engineering Corporation. Because all costs are in constant 1986 dollars, the figures must be modified to account for inflation. Interest during construction is either capitalized for the private developer or rolled into the loan for the public developer. All capital costs during construction are depreciated over the operation life of the site using straight-line depreciation for the private sector. 3 - Restrictions on the complexity of the problem: Maxima of - 100 years post-operating period, 30 years operating period, 15 years pre-operating period. The model should be used with caution outside the range of 1.8 to 10.5 million cubic feet of total volume. Depreciation is not recognized with public development

  19. Nevada National Security Site Environmental Report 2010, Attachment A: Site Description

    Energy Technology Data Exchange (ETDEWEB)

    C. Wills, ed.

    2011-09-13

    Introduction to the Nevada National Security Site Environmental Report 2010. Included are subsections that summarize the site’s geological, hydrological, climatological, and ecological setting and the cultural resources of the NNSS. The subsections are meant to aid the reader in understanding the complex physical and biological environment of the NNSS. An adequate knowledge of the site’s environment is necessary to assess the environmental impacts of new projects, design and implement environmental monitoring activities for current site operations, and assess the impacts of site operations on the public residing in the vicinity of the NNSS. The NNSS environment contributes to several key features of the site that afford protection to the inhabitants of adjacent areas from potential exposure to radioactivity or other contaminants resulting from NNSS operations. These key features include the general remote location of the NNSS, restricted access, extended wind transport times, the great depths to slow-moving groundwater, little or no surface water, and low population density. This attachment complements the annual summary of monitoring program activities and dose assessments presented in the main body of this report.

  20. Description of radiological problems at inactive uranium mill sites and formerly utilized MED/AEC sites

    International Nuclear Information System (INIS)

    Jacobs, D.G.; Dickson, H.W.

    1979-02-01

    During the early years of development of the nuclear program in the United States, more than a hundred sites were used by the Manhattan Engineer District (MED), and the U.S. Atomic Energy Commission (AEC), and/or its uranium suppliers. Many of these sites are no longer used for such activities, but in many cases, the real estate remains contaminated with radioactivity and can be a potential source of exposure to members of the general public. In addition, 22 inactive uranium mill tailings sites exist in the western part of the United States. Radioactive contamination conditions range from slight contamination on the surfaces of buildings and equipment to extensive contamination of the subsoil. The Department of Energy is conducting a program to assure that adequate precautions are taken in the management of these properties to provide the cost-effective protection of public health while permitting further use of land and other resources. Several issues which should be considered in the development of an effective policy for long-term management of such properties are identified

  1. Description of radiological problems at inactive uranium mill sites and formerly utilized MED/AEC sites

    Energy Technology Data Exchange (ETDEWEB)

    Jacobs, D.G.; Dickson, H.W.

    1979-02-01

    During the early years of development of the nuclear program in the United States, more than a hundred sites were used by the Manhattan Engineer District (MED), and the U.S. Atomic Energy Commission (AEC), and/or its uranium suppliers. Many of these sites are no longer used for such activities, but in many cases, the real estate remains contaminated with radioactivity and can be a potential source of exposure to members of the general public. In addition, 22 inactive uranium mill tailings sites exist in the western part of the United States. Radioactive contamination conditions range from slight contamination on the surfaces of buildings and equipment to extensive contamination of the subsoil. The Department of Energy is conducting a program to assure that adequate precautions are taken in the management of these properties to provide the cost-effective protection of public health while permitting further use of land and other resources. Several issues which should be considered in the development of an effective policy for long-term management of such properties are identified.

  2. Wind Atlas for South Africa (WASA) Station and Site Description Report

    DEFF Research Database (Denmark)

    Mortensen, Niels Gylling; Hansen, Jens Carsten; Kelly, Mark C.

    As part of the “Wind Atlas for South Africa” project, site inspection trips were carried out by the Council for Scientific and Industrial Research (CSIR) and Risø DTU in April and June of 2011. A total of 10 sites featuring instrumented 60-m masts were visited; the present report summarises...... the findings of the site inspection teams. The main results are descriptions and documentation of the meteorological masts, instruments and site conditions. For each site, the location and magnetic declination have been determined, as well as the sensor boom directions on the mast. Elevation maps have been...... constructed to show the surrounding terrain and photos taken to document the land cover. Finally, the observed wind roses and wind speed distribution as of 1 October 2013 are shown....

  3. Domain Endurants: An Analysis and Description Process Model

    DEFF Research Database (Denmark)

    Bjørner, Dines

    2014-01-01

    We present a summary, Sect. 2, of a structure of domain analysis and description concepts: techniques and tools. And we link, in Sect. 3, these concepts, embodied in domain analysis prompts and domain description prompts, in a model of how a diligent domain analyser cum describer would use them. We...

  4. Adding Curvature to Minimum Description Length Shape Models

    DEFF Research Database (Denmark)

    Thodberg, Hans Henrik; Ólafsdóttir, Hildur

    2003-01-01

    The Minimum Description Length (MDL) approach to shape modelling seeks a compact description of a set of shapes in terms of the coordinates of marks on the shapes. It has been shown that the mark positions resulting from this optimisation to a large extent solve the so-called point correspondence...

  5. Hydrogeochemical evaluation. Preliminary site description Forsmark area - version 1.2

    International Nuclear Information System (INIS)

    Laaksoharju, Marcus

    2005-03-01

    bedrock is estimated to be less than in other investigated sites such as Simpevarp and Laxemar, where the presence of Quaternary overburden is less important. The hydrogeologic behaviour of the Quaternary overburden in Forsmark provides a plausible explanation for the preservation of Littorina Sea signatures found in several groundwater samples, even at very shallow depths. Other (and complementary) explanations can be related with the flat topography, as well as with the fact that the Forsmark site has emerged over the sea level more recently than other investigated sites. The modelling indicates also that the groundwater composition at repository depths is such that the representative samples from KFM02A: 509-516 m and KFM03A: 448-453 m can meet the SKB chemical stability criteria for Eh, pH, TDS, DOC and Ca+Mg. In this evaluation the groundwater flow model has been updated, the salinity distribution, mixing processes and the major reactions altering the groundwaters have been modelled down to a depth of 1,000 m, and an updated Hydrogeochemical site descriptive model version 1.2 has been produced. More groundwater and isotopic data, together with microbial information, colloids and gases, provided additional site descriptive information. Finally, the introduction of coupled modelling provided further possibilities to address independently the various processes in question

  6. Hydrogeochemical evaluation. Preliminary site description Forsmark area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Laaksoharju, Marcus (ed.) [Geopoint AB, Stockholm (Sweden)

    2005-03-15

    effective recharge into the granitic bedrock is estimated to be less than in other investigated sites such as Simpevarp and Laxemar, where the presence of Quaternary overburden is less important. The hydrogeologic behaviour of the Quaternary overburden in Forsmark provides a plausible explanation for the preservation of Littorina Sea signatures found in several groundwater samples, even at very shallow depths. Other (and complementary) explanations can be related with the flat topography, as well as with the fact that the Forsmark site has emerged over the sea level more recently than other investigated sites. The modelling indicates also that the groundwater composition at repository depths is such that the representative samples from KFM02A: 509-516 m and KFM03A: 448-453 m can meet the SKB chemical stability criteria for Eh, pH, TDS, DOC and Ca+Mg. In this evaluation the groundwater flow model has been updated, the salinity distribution, mixing processes and the major reactions altering the groundwaters have been modelled down to a depth of 1,000 m, and an updated Hydrogeochemical site descriptive model version 1.2 has been produced. More groundwater and isotopic data, together with microbial information, colloids and gases, provided additional site descriptive information. Finally, the introduction of coupled modelling provided further possibilities to address independently the various processes in question.

  7. A Three site Higgsless model

    International Nuclear Information System (INIS)

    Chivukula, R. Sekhar; Coleppa, Baradhwaj; Chiara, Stefano Di; Simmons, Elizabeth H.; He, Hong-Jian; Kurachi, Masafumi; Tanabashi, Masaharu

    2006-01-01

    We analyze the spectrum and properties of a highly deconstructed Higgsless model with only three sites. Such a model contains sufficient complexity to incorporate interesting physics issues related to fermion masses and electroweak observables, yet remains simple enough that it could be encoded in a Matrix Element Generator program for use with Monte Carlo simulations. The gauge sector of this model is equivalent to that of the Breaking Electroweak Symmetry Strongly (BESS) model; the new physics of interest here lies in the fermion sector. We analyze the form of the fermion Yukawa couplings required to produce the ideal fermion delocalization that causes tree-level precision electroweak corrections to vanish. We discuss the size of one-loop corrections to b→sγ, the weak-isospin violating parameter αT and the decay Z→bb. We find that the new fermiophobic vector states (the analogs of the gauge-boson Kaluza-Klein modes in a continuum model) can be reasonably light, with a mass as low as 380 GeV, while the extra (approximately vectorial) quark and lepton states (the analogs of the fermion Kaluza-Klein modes) must be heavier than 1.8 TeV

  8. Shell model description of Ge isotopes

    International Nuclear Information System (INIS)

    Hirsch, J G; Srivastava, P C

    2012-01-01

    A shell model study of the low energy region of the spectra in Ge isotopes for 38 ≤ N ≤ 50 is presented, analyzing the excitation energies, quadrupole moments, B(E2) values and occupation numbers. The theoretical results have been compared with the available experimental data. The shell model calculations have been performed employing three different effective interactions and valence spaces. We have used two effective shell model interactions, JUN45 and jj44b, for the valence space f 5/2 pg 9/2 without truncation. To include the proton subshell f 7/2 in valence space we have employed the fpg effective interaction due to Sorlin et al., with 48 Ca as a core and a truncation in the number of excited particles.

  9. The self-description data configuration model

    Energy Technology Data Exchange (ETDEWEB)

    Abadie, Lana, E-mail: lana.abadie@iter.org [ITER Organization, Route de vinon sur Verdon, 13115 St Paul Lez Durance (France); Di Maio, Franck; Klotz, Wolf-Dieter; Mahajan, Kirti; Stepanov, Denis; Utzel, Nadine; Wallander, Anders [ITER Organization, Route de vinon sur Verdon, 13115 St Paul Lez Durance (France)

    2012-12-15

    Highlights: Black-Right-Pointing-Pointer We use the relational model to represent the configuration data for ITER. Black-Right-Pointing-Pointer We explain the different modeled views namely physical, functional and control. Black-Right-Pointing-Pointer We explain how this information is used to generate configuration files. Black-Right-Pointing-Pointer We explain that this information is validated. - Abstract: ITER will consist of roughly 160 plant systems I and C delivered in kind which need to be integrated into the ITER control infrastructure. To make the integration of all these plant systems I and C, a smooth operation, the CODAC (Controls, Data Access and Communications) group release every year the core software environment which consists of many applications. In this paper we would like to describe what configuration data and how it is modeled in the version 2. The model is based on three views, the physical one which lists the components with their signals, the functional view which describes the control functions and variables required to implement them and the control view which links the two previous views. We use Hibernate as an ORM (Object Relational Mapping) framework with a PostgreSQL database and Spring as a framework to handle transactions.

  10. Description of a comprehensive mathematical model

    DEFF Research Database (Denmark)

    Li, Xiyan; Yin, Chungen

    2017-01-01

    Biomass gasification is still a promising technology after over 30 years’ research and development and has success only in a few niche markets. In this paper, a comprehensive mathematical model for biomass particle gasification is developed within a generic particle framework, assuming the feed...

  11. Pair shell model description of collective motions

    International Nuclear Information System (INIS)

    Chen Hsitseng; Feng Dahsuan

    1996-01-01

    The shell model in the pair basis has been reviewed with a case study of four particles in a spherical single-j shell. By analyzing the wave functions according to their pair components, the novel concept of the optimum pairs was developed which led to the proposal of a generalized pair mean-field method to solve the many-body problem. The salient feature of the method is its ability to handle within the framework of the spherical shell model a rotational system where the usual strong configuration mixing complexity is so simplified that it is now possible to obtain analytically the band head energies and the moments of inertia. We have also examined the effects of pair truncation on rotation and found the slow convergence of adding higher spin pairs. Finally, we found that when the SDI and Q .Q interactions are of equal strengths, the optimum pair approximation is still valid. (orig.)

  12. Model for safety reports including descriptive examples

    International Nuclear Information System (INIS)

    1995-12-01

    Several safety reports will be produced in the process of planning and constructing the system for disposal of high-level radioactive waste in Sweden. The present report gives a model, with detailed examples, of how these reports should be organized and what steps they should include. In the near future safety reports will deal with the encapsulation plant and the repository. Later reports will treat operation of the handling systems and the repository

  13. A Descriptive Evaluation of Software Sizing Models

    Science.gov (United States)

    1987-09-01

    2-22 2.3.2 SPQR Sizer/FP ............................... 2-25 2.3.3 QSM Size Planner: Function Points .......... 2-26 2.3.4 Feature...Characteristics ............................. 4-20 4.5.3 Results and Conclusions ..................... 4-20 4.6 Application of the SPQR SIZER/FP Approach...4-19 4-7 SPQR Function Point Estimate for the CATSS Sensitivity Model .................................................. 4-23 4-8 ASSET-R

  14. ECOPATH: Model description and evaluation of model performance

    International Nuclear Information System (INIS)

    Bergstroem, U.; Nordlinder, S.

    1996-01-01

    The model is based upon compartment theory and it is run in combination with a statistical error propagation method (PRISM, Gardner et al. 1983). It is intended to be generic for application on other sites with simple changing of parameter values. It was constructed especially for this scenario. However, it is based upon an earlier designed model for calculating relations between released amount of radioactivity and doses to critical groups (used for Swedish regulations concerning annual reports of released radioactivity from routine operation of Swedish nuclear power plants (Bergstroem och Nordlinder, 1991)). The model handles exposure from deposition on terrestrial areas as well as deposition on lakes, starting with deposition values. 14 refs, 16 figs, 7 tabs

  15. Model description and evaluation of model performance: DOSDIM model

    International Nuclear Information System (INIS)

    Lewyckyj, N.; Zeevaert, T.

    1996-01-01

    DOSDIM was developed to assess the impact to man from routine and accidental atmospheric releases. It is a compartmental, deterministic, radiological model. For an accidental release, dynamic transfer are used in opposition to a routine release for which equilibrium transfer factors are used. Parameters values were chosen to be conservative. Transfer between compartments are described by first-order differential equations. 2 figs

  16. Technical description of the RIVM trajectory model

    Energy Technology Data Exchange (ETDEWEB)

    De Waal, E.S.; Van Pul, W.A.J.

    1995-12-01

    The RIVM trajectory model, described in this report, enables calculation of a backward or forward trajectory. These trajectories are used to `follow` previous released air pollution in a backward mode or to `find` the origin of air pollution in a forward mode. The trajectories are used in the smog forecasting and in the TREND model for the distribution of materials in Europe. Presently 6-hourly ECMWF wind fields at 1000 and 850 hPa, with 3 deg x 3 deg latitude-longitude resolution are used. Wind fields with a different resolution in latitude-longitude can also be used after simple adjustments. An iterative method, described elsewhere, is applied to calculate the trajectories. Within limits, the user is free to choose the time step (1, 2 or 6-hour), transport height, length, starting or arrival date and starting or arrival position of the trajectory. The differences between the trajectories calculated with time steps of 1, 2 and 6 h were small. For the 96-hour trajectories at 1000 and 850 hPa the deviations were generally within 1 deg latitude and longitude, i.e. 100-200 km. The trajectory calculated with the 6-hour time step could be used without a great loss in accuracy compared to the calculations with the 1-hour time step. A typical error in the trajectory path at 1000 and 850 hPa was 500 km, which is about 30% of a typical travel distance. However, close to quickly changing weather systems, such as cyclones, the error can be as large as the travel distance and makes the calculations unreliable. The error in the forecasted trajectory was found to be larger than the above error estimation due to larger uncertainties in the forecasted compared to the analyzed wind fields. A manual on how to run the model is also given. 5 figs., 3 tabs., 5 refs., 6 appendices

  17. Social European Model between Descriptive and Contrafactual

    Directory of Open Access Journals (Sweden)

    Liviu-Catalin Moraru

    2006-05-01

    Full Text Available Romania is about to become a member of EU and to participate, in an active way, to the european dream. After a short presentation of the origins of social market economy, authors analyze european social model, emphasizing the main dificulties of the present european construction. The paper ends with a comparative analisys of two different economic policies, being offered strong arguments in favor of pro-market policies. On long term, the only way to increase the economic prosperity (in the EU is by stimulating institutional competition, protecting property rights and liberty in order to increase welfare, and not by redistribution and uniformization.

  18. DETRA: Model description and evaluation of model performance

    International Nuclear Information System (INIS)

    Suolanen, V.

    1996-01-01

    The computer code DETRA is a generic tool for environmental transfer analyses of radioactive or stable substances. The code has been applied for various purposes, mainly problems related to the biospheric transfer of radionuclides both in safety analyses of disposal of nuclear wastes and in consideration of foodchain exposure pathways in the analyses of off-site consequences of reactor accidents. For each specific application an individually tailored conceptual model can be developed. The biospheric transfer analyses performed by the code are typically carried out for terrestrial, aquatic and food chain applications. 21 refs, 35 figs, 15 tabs

  19. Radiological investigations at the 'Taiga' nuclear explosion site: Site description and in situ measurements

    Energy Technology Data Exchange (ETDEWEB)

    Ramzaev, V., E-mail: V.Ramzaev@mail.ru [Institute of Radiation Hygiene, Mira str. 8, 197101 St.-Petersburg (Russian Federation); Repin, V.; Medvedev, A.; Khramtsov, E.; Timofeeva, M.; Yakovlev, V. [Institute of Radiation Hygiene, Mira str. 8, 197101 St.-Petersburg (Russian Federation)

    2011-07-15

    In the summer of 2009, we performed a field survey of the 'Taiga' peaceful underground nuclear explosion site, the Perm region, Russia (61.30{sup o} N, 56.60{sup o} E). The explosion was carried out by the USSR in 1971. This paper provides an extended summary of the available published data on the 'Taiga' experiment. A detailed description of the site is illustrated by original aerial and ground-level photos. A large artificial lake (700 m long and 350 m wide) currently occupies the central area of the experimental site. The ground lip surrounding the lake is covered by a newly grown mixed forest. In situ measurements, performed in August 2009, revealed elevated levels of the {gamma}-ray dose rate in air on the banks of the lake 'Taiga'. Two hot spots were detected on the eastern bank of the lake. The excess of the {gamma}-ray radiation is attributable to the man-made radionuclides {sup 60}Co and {sup 137}Cs. The current external {gamma}-ray dose rate to a human from the contaminations associated with the 'Taiga' experiment was between 9 and 70 {mu}Sv per week. Periodic monitoring the site is recommended. - Highlights: > We studied a radiation anomaly at the 'Taiga' underground nuclear explosion site. > The anomaly currently has an area of approximately 1 km{sup 2}. > The excess of {gamma}-ray radiation at the site is mainly attributable to {sup 60}Co and {sup 137}Cs. > The external effective dose may currently exceed the negligible value of 10 {mu}Sv y{sup -1}.

  20. The DART general equilibrium model: A technical description

    OpenAIRE

    Springer, Katrin

    1998-01-01

    This paper provides a technical description of the Dynamic Applied Regional Trade (DART) General Equilibrium Model. The DART model is a recursive dynamic, multi-region, multi-sector computable general equilibrium model. All regions are fully specified and linked by bilateral trade flows. The DART model can be used to project economic activities, energy use and trade flows for each of the specified regions to simulate various trade policy as well as environmental policy scenarios, and to analy...

  1. Fixed site neutralization model programmer's manual. Volume 1

    International Nuclear Information System (INIS)

    Engi, D.; Chapman, L.; Judnick, W.; Blum, R.; Broegler, L.; Lenz, J.; Weinthraub, A.; Ballard, D.

    1979-12-01

    The Fixed Site Neutralization Model (FSNM) is a stochastic, time-stepped simulation of an engagement process whereby an adversary force attempts to steal or sabotage sensitive (e.g., nuclear) materials being guarded by a security force on a fixed site and a response force that is off-site. FSNM will assist regulatory bodies of the US Government in evaluating fixed site physical protection systems at various installations in a variety of scenarios. Most data input to the Fixed Site Neutralization Model are in binary form. The user's data are transformed into binary form by two supporting modules, the Data Preprocessor (DPP) and the Plex Preprocessor (PPP). Both preprocessors and the FSNM itself are written in FORTRAN. This volume of the program maintenance program contains: introduction, logic descriptions, PLEX data structure, PLEX records, dictionaries, and error conditions and comments

  2. A Description Logic Based Knowledge Representation Model for Concept Understanding

    DEFF Research Database (Denmark)

    Badie, Farshad

    2017-01-01

    This research employs Description Logics in order to focus on logical description and analysis of the phenomenon of ‘concept understanding’. The article will deal with a formal-semantic model for figuring out the underlying logical assumptions of ‘concept understanding’ in knowledge representation...... systems. In other words, it attempts to describe a theoretical model for concept understanding and to reflect the phenomenon of ‘concept understanding’ in terminological knowledge representation systems. Finally, it will design an ontology that schemes the structure of concept understanding based...

  3. Algebraic computability and enumeration models recursion theory and descriptive complexity

    CERN Document Server

    Nourani, Cyrus F

    2016-01-01

    This book, Algebraic Computability and Enumeration Models: Recursion Theory and Descriptive Complexity, presents new techniques with functorial models to address important areas on pure mathematics and computability theory from the algebraic viewpoint. The reader is first introduced to categories and functorial models, with Kleene algebra examples for languages. Functorial models for Peano arithmetic are described toward important computational complexity areas on a Hilbert program, leading to computability with initial models. Infinite language categories are also introduced to explain descriptive complexity with recursive computability with admissible sets and urelements. Algebraic and categorical realizability is staged on several levels, addressing new computability questions with omitting types realizably. Further applications to computing with ultrafilters on sets and Turing degree computability are examined. Functorial models computability is presented with algebraic trees realizing intuitionistic type...

  4. Descriptions of representative contaminated sites and facilities within the DOE complex

    International Nuclear Information System (INIS)

    Short, S.M.; Buck, J.W.; Clark, L.L.; Fletcher, J.F.; Glantz, C.S.; Holdren, G.R.; Huesties, L.R.; Williams, M.D.; Oates, L.

    1994-10-01

    The U.S. Department of Energy (DOE) has initiated efforts to prepare a Programmatic Environmental Impact Statement (PEIS) that will analyze the existing environmental restoration and waste management program and evaluate alternatives for an integrated program. The alternatives being evaluated include (1) a open-quotes No Actionclose quotes alternative as required by the National Environmental Policy Act (NEPA), (2) an Applicable, Relevant, and Appropriate Requirements (ARAR)-driven alternative, (3) a land-use-driven alternative, (4) a health-risk-driven alternative, and (5) a combination land-use and health-risk-driven alternative. The analytical approach being taken to evaluate each of these alternatives is to perform a remedial engineering analysis and human health and ecosystem effects analyses on every contaminated site and facility in the DOE complex. One of Pacific Northwest Laboratory's (PNL) roles in this approach has been to compile the source term and environmental setting data needed to drive each of these analyses. To date, over 10,000 individual contaminated sites and facilities located throughout the DOE complex of installations have been identified and at least some minimal data compiled on each. The PEIS analyses have been appreciably simplified by categorizing all of these contaminated sites and facilities into six broad categories: (1) contaminated buildings, (2) contaminated soils, (3) solid waste sites (e.g., burial grounds), (4) liquid containment structures (e.g., tanks), (5) surface water sites, and (6) contaminated groundwater sites. A report containing a complete description of each of these thousands of contaminated sites and facilities would be tremendously large and unwildy, as would separate reports describing the application of the analytical methodologies to each

  5. Preliminary site description Laxemar stage 2.1. Feedback for completion of the site investigation including input from safety assessment and repository engineering

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-09-15

    The Laxemar subarea is the focus for the complete site investigations in the Simpevarp area. The south and southwestern parts of the subarea (the so-called 'focused area') have been designated for focused studies during the remainder of the site investigations. This area, some 5.3 square kilometres in size, is characterised on the surface by an arc shaped body of quartz monzodiorite gently dipping to the north, flanked in the north and south by Aevroe granite. The current report documents work conducted during stage 2.1 of the site-descriptive modelling of the Laxemar subarea. The primary objective of the work performed is to provide feedback to the site investigations at Laxemar to ensure that adequate and timely data and information are obtained during the remaining investigation stage. The work has been conducted in cooperation with the site investigation team at Laxemar and representatives from safety assessment and repository engineering. The principal aim of this joint effort has been to safeguard that adequate data are collected that resolve the remaining issues/uncertainties which are of importance for repository layout and long-term safety. The proposed additional works presented in this report should be regarded as recommended additions and/or modifications in relation to the CSI programme published early 2006. The overall conclusion of the discipline-wise review of critical issues is that the CSI programme overall satisfies the demands to resolve the remaining uncertainties. This is interpreted to be partly a result of the close interaction between the site modelling team, site investigation team and the repository engineering teams, which has been in operation since early 2005. In summary, the performed interpretations and modelling have overall confirmed the version 1.2 results. The exception being Hydrogeology where the new Laxemar 2.1 borehole data suggest more favourable conditions in the south and west parts of the focused area compared

  6. Preliminary site description Laxemar stage 2.1. Feedback for completion of the site investigation including input from safety assessment and repository engineering

    International Nuclear Information System (INIS)

    2006-09-01

    The Laxemar subarea is the focus for the complete site investigations in the Simpevarp area. The south and southwestern parts of the subarea (the so-called 'focused area') have been designated for focused studies during the remainder of the site investigations. This area, some 5.3 square kilometres in size, is characterised on the surface by an arc shaped body of quartz monzodiorite gently dipping to the north, flanked in the north and south by Aevroe granite. The current report documents work conducted during stage 2.1 of the site-descriptive modelling of the Laxemar subarea. The primary objective of the work performed is to provide feedback to the site investigations at Laxemar to ensure that adequate and timely data and information are obtained during the remaining investigation stage. The work has been conducted in cooperation with the site investigation team at Laxemar and representatives from safety assessment and repository engineering. The principal aim of this joint effort has been to safeguard that adequate data are collected that resolve the remaining issues/uncertainties which are of importance for repository layout and long-term safety. The proposed additional works presented in this report should be regarded as recommended additions and/or modifications in relation to the CSI programme published early 2006. The overall conclusion of the discipline-wise review of critical issues is that the CSI programme overall satisfies the demands to resolve the remaining uncertainties. This is interpreted to be partly a result of the close interaction between the site modelling team, site investigation team and the repository engineering teams, which has been in operation since early 2005. In summary, the performed interpretations and modelling have overall confirmed the version 1.2 results. The exception being Hydrogeology where the new Laxemar 2.1 borehole data suggest more favourable conditions in the south and west parts of the focused area compared with the

  7. Withdrawal-associated injury site pain (WISP): a descriptive case series of an opioid cessation phenomenon.

    Science.gov (United States)

    Rieb, Launette Marie; Norman, Wendy V; Martin, Ruth Elwood; Berkowitz, Jonathan; Wood, Evan; McNeil, Ryan; Milloy, M-J

    2016-12-01

    Withdrawal pain can be a barrier to opioid cessation. Yet, little is known about old injury site pain in this context. We conducted an exploratory mixed-methods descriptive case series using a web-based survey and in-person interviews with adults recruited from pain and addiction treatment and research settings. We included individuals who self-reported a past significant injury that was healed and pain-free before the initiation of opioids, which then became temporarily painful upon opioid cessation-a phenomenon we have named withdrawal-associated injury site pain (WISP). Screening identified WISP in 47 people, of whom 34 (72%) completed the descriptive survey, including 21 who completed qualitative interviews. Recalled pain severity scores for WISP were typically high (median: 8/10; interquartile range [IQR]: 2), emotionally and physically aversive, and took approximately 2 weeks to resolve (median: 14; IQR: 24 days). Withdrawal-associated injury site pain intensity was typically slightly less than participants' original injury pain (median: 10/10; IQR: 3), and more painful than other generalized withdrawal symptoms which also lasted approximately 2 weeks (median: 13; IQR: 25 days). Fifteen surveyed participants (44%) reported returning to opioid use because of WISP in the past. Participants developed theories about the etiology of WISP, including that the pain is the brain's way of communicating a desire for opioids. This research represents the first known documentation that previously healed, and pain-free injury sites can temporarily become painful again during opioid withdrawal, an experience which may be a barrier to opioid cessation, and a contributor to opioid reinitiation.

  8. Descriptive models for single-jet sluicing of sludge waste

    International Nuclear Information System (INIS)

    Erian, F.F.; Mahoney, L.A.; Terrones, G.

    1997-12-01

    Mobilization of sludge waste stored in underground storage tanks can be achieved safely and reliably by sluicing. In the project discussed in this report, the waste in Hanford single-shell Tank 241-C-106 will be mobilized by sluicing, retrieved by a slurry retrieval pump, and transferred via an 1800-ft slurry pipeline to Tank 241-AY-102. A sluicing strategy must be developed that ensures efficient use of the deployed configuration of the sluicing system: the nozzle(s) and the retrieval pump(s). Given a sluicing system configuration in a particular tank, it is desirable to prescribe the sequential locations at which the sludge will be mobilized and retrieved and the rate at which these mobilization and retrieval processes take place. In addition, it is necessary to know whether the retrieved waste slurry meets the requirements for cross-site slurry transport. Some of the physical phenomena that take place during mobilization and retrieval and certain aspects of the sluicing process are described in this report. First, a mathematical model gives (1) an idealized geometrical representation of where, within the confines of a storage tank containing a certain amount of settled waste, sludge can be removed and mobilized; and (2) a quantitative measure of the amount of sludge that can be removed during a sluicing campaign. A model describing an idealized water jet issuing from a circular nozzle located at a given height above a flat surface is also presented in this report. This dynamic water-jet model provides the basis for improving the geometrical sluicing model presented next. In this model the authors assume that the water jet follows a straight trajectory toward a target point on a flat surface. However, the water jet does not follow a straight line in the actual tank, and using the true trajectory will allow a more accurate estimate of the amount of disturbed material. Also, the authors hope that developing accurate force and pressure fields will lead to a better

  9. Descriptive and mechanistic models of crop–weed competition

    NARCIS (Netherlands)

    Bastiaans, L.; Storkey, J.

    2017-01-01

    Crop-weed competitive relations are an important element of agroecosystems. Quantifying and understanding them helps to design appropriate weed management at operational, tactical and strategic level. This chapter presents and discusses simple descriptive and more mechanistic models for crop-weed

  10. Organization model and formalized description of nuclear enterprise information system

    International Nuclear Information System (INIS)

    Yuan Feng; Song Yafeng; Li Xudong

    2012-01-01

    Organization model is one of the most important models of Nuclear Enterprise Information System (NEIS). Scientific and reasonable organization model is the prerequisite that NEIS has robustness and extendibility, and is also the foundation of the integration of heterogeneous system. Firstly, the paper describes the conceptual model of the NEIS on ontology chart, which provides a consistent semantic framework of organization. Then it discusses the relations between the concepts in detail. Finally, it gives the formalized description of the organization model of NEIS based on six-tuple array. (authors)

  11. Contaminant transport modeling studies of Russian sites

    International Nuclear Information System (INIS)

    Tsang, Chin-Fu

    1993-01-01

    Lawrence Berkeley Laboratory (LBL) established mechanisms that promoted cooperation between U.S. and Russian scientists in scientific research as well as environmental technology transfer. Using Russian experience and U.S technology, LBL developed approaches for field investigations, site evaluation, waste disposal, and remediation at Russian contaminated sites. LBL assessed a comprehensive database as well as an actual, large-scale contaminated site to evaluate existing knowledge of and test mathematical models used for the assessment of U.S. contaminated sites

  12. Wind resource modelling for micro-siting - Validation at a 60-MW wind farm site

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, J C; Gylling Mortensen, N [Risoe National Lab., Wind Energy and Atmospheric Physics Dept., Roskilde (Denmark); Said, U S [New and Renewable Energy Authority, Cairo (Egypt)

    1999-03-01

    This paper investigates and validates the applicability of the WAsP-model for layout optimization and micro-siting of wind turbines at a given site for a 60-MW wind farm at Zafarana at the Gulf of Suez in Egypt. Previous investigations show large gradients in the wind climate within the area. For the design and optimization of the wind farm it was found necessary to verify the WAsP extrapolation of wind atlas results from 2 existing meteorological masts located 5 and 10 km, respectively, from the wind farm site. On-site measurements at the 3.5 x 3.5 km{sup 2} wind farm site in combination with 7 years of near-site wind atlas measurements offer significant amounts of data for verification of wind conditions for micro-siting. Wind speeds, wind directions, turbulence intensities and guests in 47.5 m a.g.l. have been measured at 9 locations across the site. Additionally, one of the site masts is equipped as a reference mast, measuring both vertical profiles of wind speed and temperature as well as air pressure and temperature. The exercise is further facilitated by the fact that winds are highly uni-directional; the north direction accounting for 80-90% of the wind resource. The paper presents comparisons of 5 months of on-site measurements and modeled predictions from 2 existing meteorological masts located at distances of 5 and 10 km, respectively, from the wind farm site. Predictions based on terrain descriptions of the Wind Atlas for the Gulf of Suez 1991-95 showed over-predictions of wind speeds of 4-10%. With calibrated terrain descriptions, made based on measured data and a re-visit to critical parts of the terrain, the average prediction error of wind speeds was reduced to about 1%. These deviations are smaller than generally expected for such wind resource modeling, clearly documenting the validity of using WAsP modeling for micro-siting and layout optimization of the wind farm. (au)

  13. Quality Assurance Based on Descriptive and Parsimonious Appearance Models

    DEFF Research Database (Denmark)

    Nielsen, Jannik Boll; Eiríksson, Eyþór Rúnar; Kristensen, Rasmus Lyngby

    2015-01-01

    In this positional paper, we discuss the potential benefits of using appearance models in additive manufacturing, metal casting, wind turbine blade production, and 3D content acquisition. Current state of the art in acquisition and rendering of appearance cannot easily be used for quality assurance...... in these areas. The common denominator is the need for descriptive and parsimonious appearance models. By ‘parsimonious’ we mean with few parameters so that a model is useful both for fast acquisition, robust fitting, and fast rendering of appearance. The word ‘descriptive’ refers to the fact that a model should...

  14. Three multimedia models used at hazardous and radioactive waste sites

    International Nuclear Information System (INIS)

    Moskowitz, P.D.; Pardi, R.; Fthenakis, V.M.; Holtzman, S.; Sun, L.C.; Rambaugh, J.O.; Potter, S.

    1996-02-01

    Multimedia models are used commonly in the initial phases of the remediation process where technical interest is focused on determining the relative importance of various exposure pathways. This report provides an approach for evaluating and critically reviewing the capabilities of multimedia models. This study focused on three specific models MEPAS Version 3.0, MMSOILS Version 2.2, and PRESTO-EPA-CPG Version 2.0. These models evaluate the transport and fate of contaminants from source to receptor through more than a single pathway. The presence of radioactive and mixed wastes at a site poses special problems. Hence, in this report, restrictions associated with the selection and application of multimedia models for sites contaminated with radioactive and mixed wastes are highlighted. This report begins with a brief introduction to the concept of multimedia modeling, followed by an overview of the three models. The remaining chapters present more technical discussions of the issues associated with each compartment and their direct application to the specific models. In these analyses, the following components are discussed: source term; air transport; ground water transport; overland flow, runoff, and surface water transport; food chain modeling; exposure assessment; dosimetry/risk assessment; uncertainty; default parameters. The report concludes with a description of evolving updates to the model; these descriptions were provided by the model developers

  15. Preliminary safety evaluation for the Simpevarp subarea. Based on data and site descriptions after the initial site investigation stage

    International Nuclear Information System (INIS)

    2005-04-01

    The main objectives of this Preliminary safety evaluation (PSE) of the Simpevarp subarea are: to determine, whether the feasibility study's judgement of the suitability of the candidate area with respect to long-term safety holds up in the light of the site investigation data; to provide feedback to continued site investigations and site-specific repository design and to identify site specific scenarios and geoscientific issues for further analyses. The PSE focuses on comparing the attained knowledge of the sites with the suitability criteria as set out by SKB in the report SKB-TR--00-12. These criteria both concern properties of the site judged to be necessary for safety and engineering (requirements) and properties judged to be beneficial (preferences). The findings are then evaluated in order to provide feedback to continued investigations and design work. The PSE does not aim at comparing sites and does not assess compliance with safety and radiation protection criteria. The evaluation shows that even considering remaining uncertainties, the Simpevarp subarea meets all safety requirements and most of the safety preferences. Consequently, from a safety point of view, there is no reason not to continue the Site Investigations of the Simpevarp subarea. There are still uncertainties to resolve and the safety would eventually need to be verified through a full safety assessment. Still, this Preliminary Safety Evaluation demonstrates that it is likely that a safe repository for spent nuclear fuel of the KBS-3 type could be constructed at the site. The following feedback is provided to the site investigations and the associated site modelling: Reducing the uncertainty on the deformation zone geometry within the Simpevarp subarea would allow for a more specified layout, although the sensitivity analysis shows that the space needed is rather robust with respect to uncertainties in the zones. There is substantial uncertainty in the discrete fracture network (DFN) model

  16. Fixed-site physical protection system modeling

    International Nuclear Information System (INIS)

    Chapman, L.D.

    1975-01-01

    An evaluation of a fixed-site safeguard security system must consider the interrelationships of barriers, alarms, on-site and off-site guards, and their effectiveness against a forcible adversary attack whose intention is to create an act of sabotage or theft. A computer model has been developed at Sandia Laboratories for the evaluation of alternative fixed-site security systems. Trade-offs involving on-site and off-site response forces and response times, perimeter alarm systems, barrier configurations, and varying levels of threat can be analyzed. The computer model provides a framework for performing inexpensive experiments on fixed-site security systems for testing alternative decisions, and for determining the relative cost effectiveness associated with these decision policies

  17. Documentation for Grants Equal to Tax model: Volume 1, Technical description

    International Nuclear Information System (INIS)

    1986-01-01

    A computerized model, the Grants Equal to Tax (GETT) model, was developed to assist in evaluating the amount of federal grant monies that would go to state and local jurisdictions under the provisions outlined in the Nuclear Waste Policy Act of 1982. The GETT model is capable of forecasting the amount of tax liability associated with all property owned and all activities undertaken by the US Department of Energy (DOE) in site characterization and repository development. The GETT program is a user-friendly, menu-driven model developed using dBASE III/trademark/, a relational data base management system. The data base for GETT consists primarily of eight separate dBASE III/trademark/ files corresponding to each of the eight taxes levied by state and local jurisdictions on business property and activity. Additional smaller files help to control model inputs and reporting options. Volume 1 of the GETT model documentation is a technical description of the program and its capabilities providing (1) descriptions of the data management system and its procedures; (2) formulas for calculating taxes (illustrated with flow charts); (3) descriptions of tax data base variables for the Deaf Smith County, Texas, Richton Dome, Mississippi, and Davis Canyon, Utah, salt sites; and (4) data inputs for the GETT model. 10 refs., 18 figs., 3 tabs

  18. Hydrodynamic description of spin Calogero-Sutherland model

    Science.gov (United States)

    Abanov, Alexander; Kulkarni, Manas; Franchini, Fabio

    2009-03-01

    We study a non-linear collective field theory for an integrable spin-Calogero-Sutherland model. The hydrodynamic description of this SU(2) model in terms of charge density, charge velocity and spin currents is used to study non-perturbative solutions (solitons) and examine their correspondence with known quantum numbers of elementary excitations [1]. A conventional linear bosonization or harmonic approximation is not sufficient to describe, for example, the physics of spin-charge (non)separation. Therefore, we need this new collective bosonic field description that captures the effects of the band curvature. In the strong coupling limit [2] this model reduces to integrable SU(2) Haldane-Shastry model. We study a non-linear coupling of left and right spin currents which form a Kac-Moody algebra. Our quantum hydrodynamic description for the spin case is an extension for the one found in the spinless version in [3].[3pt] [1] Y. Kato,T. Yamamoto, and M. Arikawa, J. Phys. Soc. Jpn. 66, 1954-1961 (1997).[0pt] [2] A. Polychronakos, Phys Rev Lett. 70,2329-2331(1993).[0pt] [3] A.G.Abanov and P.B. Wiegmann, Phys Rev Lett 95, 076402(2005)

  19. Gray-box modelling approach for description of storage tunnel

    DEFF Research Database (Denmark)

    Harremoës, Poul; Carstensen, Jacob

    1999-01-01

    The dynamics of a storage tunnel is examined using a model based on on-line measured data and a combination of simple deterministic and black-box stochastic elements. This approach, called gray-box modeling, is a new promising methodology for giving an on-line state description of sewer systems...... of the water in the overflow structures. The capacity of a pump draining the storage tunnel is estimated for two different rain events, revealing that the pump was malfunctioning during the first rain event. The proposed modeling approach can be used in automated online surveillance and control and implemented...

  20. Description of transitional nuclei in the sdg boson model

    International Nuclear Information System (INIS)

    Lac, V.S.; Kuyucak, S.

    1992-01-01

    The study of the transitional nuclei in the framework of the sdg boson model was necessitated by recent measurements of E2 and E4 transitions in the Pt and Os isotopes which can not be explained in the sd boson models. It is shown how γ-unstable and triaxial shapes arise from special choices of sdg model Hamiltonians. Ways of limiting the number of free parameters through consistency and coherence conditions are also discussed. A satisfactory description of E2 and E4 properties is obtained for the Pt and Os nuclei, which also predicts dynamic shape transitions in these nuclei. 36 refs., 10 tabs., 12 figs

  1. Description of transitional nuclei in the sdg boson model

    International Nuclear Information System (INIS)

    Lac, V.S.; Kuyucak, S.

    1992-01-01

    We study the transitional nuclei in the framework of the sdg boson model. This extension is necessitated by recent measurements of E2 and E4 transitions in the Pt and Os isotopes which can not be explained in the sd boson models. We show how γ-unstable and triaxial shapes arise from special choices of sdg model hamiltonians and discuss ways of limiting the number of free parameters through consistency and coherence conditions. A satisfactory description of E2 and E4 properties is obtained for the Pt and Os nuclei, which also predicts dynamic shape transitions in these nuclei. (orig.)

  2. Description of transitional nuclei in the sdg boson model

    Science.gov (United States)

    Lac, V.-S.; Kuyucak, S.

    1992-03-01

    We study the transitional nuclei in the framework of the sdg boson model. This extension is necessitated by recent measurements of E2 and E4 transitions in the Pt and Os isotopes which can not be explained in the sd boson models. We show how γ-unstable and triaxial shapes arise from special choices of sdg model hamiltonians and discuss ways of limiting the number of free parameters through consistency and coherence conditions. A satisfactory description of E2 and E4 properties is obtained for the Pt and Os nuclei, which also predicts dynamic shape transitions in these nuclei.

  3. Description of transitional nuclei in the sdg boson model

    Energy Technology Data Exchange (ETDEWEB)

    Lac, V.S.; Kuyucak, S. (School of Physics, Univ. Melbourne, Victoria (Australia))

    1992-03-30

    We study the transitional nuclei in the framework of the sdg boson model. This extension is necessitated by recent measurements of E2 and E4 transitions in the Pt and Os isotopes which can not be explained in the sd boson models. We show how {gamma}-unstable and triaxial shapes arise from special choices of sdg model hamiltonians and discuss ways of limiting the number of free parameters through consistency and coherence conditions. A satisfactory description of E2 and E4 properties is obtained for the Pt and Os nuclei, which also predicts dynamic shape transitions in these nuclei. (orig.).

  4. Preliminary safety evaluation for the Forsmark area. Based on data and site descriptions after the initial site investigation stage

    International Nuclear Information System (INIS)

    Andersson, Johan

    2005-08-01

    The main objectives of this Preliminary Safety Evaluation (PSE) of the Forsmark area have been to determine, with limited efforts, whether the feasibility study's judgement of the suitability of the candidate area with respect to long-term safety holds up in the light of the actual site investigation data; to provide feedback to continued site investigations and site-specific repository design and to identify site-specific scenarios and geoscientific issues for further analyses. The PSE focuses on comparing the attained knowledge of the sites with the suitability criteria as set out by SKB. The PSE does not aim at comparing sites and does not assess compliance with safety and radiation protection criteria. The evaluation shows that, even considering remaining uncertainties, the Forsmark area meets all stated safety requirements and preferences. Consequently, from a safety point of view, there is no reason not to continue the Site Investigations of the Forsmark area. There are still uncertainties to resolve and the safety would eventually need to be verified through a full safety assessment. Nevertheless, this Preliminary Safety Evaluation demonstrates that it is likely that a safe repository for spent nuclear fuel of the KBS-3 type could be constructed at the site. The following feedback is provided to the site investigations and the associated site modelling: Reducing the uncertainty on the deformation zone geometry inside the target area would be needed to more firmly define locations of the suitable deposition volumes. There is substantial uncertainty in the Discrete Fracture Network model. Further reduction of the uncertainties, if needed, would probably only be possible from the underground, detailed investigation phase. Efforts need also be spent on improving the DFN-modelling. There are assumptions made in current models that could be challenged and there seems to be room for better use of the borehole information. It is particularly important to provide

  5. Preliminary safety evaluation for the Forsmark area. Based on data and site descriptions after the initial site investigation stage

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Johan [JA Streamflow AB, Aelvsjoe (Sweden)

    2005-08-01

    The main objectives of this Preliminary Safety Evaluation (PSE) of the Forsmark area have been to determine, with limited efforts, whether the feasibility study's judgement of the suitability of the candidate area with respect to long-term safety holds up in the light of the actual site investigation data; to provide feedback to continued site investigations and site-specific repository design and to identify site-specific scenarios and geoscientific issues for further analyses. The PSE focuses on comparing the attained knowledge of the sites with the suitability criteria as set out by SKB. The PSE does not aim at comparing sites and does not assess compliance with safety and radiation protection criteria. The evaluation shows that, even considering remaining uncertainties, the Forsmark area meets all stated safety requirements and preferences. Consequently, from a safety point of view, there is no reason not to continue the Site Investigations of the Forsmark area. There are still uncertainties to resolve and the safety would eventually need to be verified through a full safety assessment. Nevertheless, this Preliminary Safety Evaluation demonstrates that it is likely that a safe repository for spent nuclear fuel of the KBS-3 type could be constructed at the site. The following feedback is provided to the site investigations and the associated site modelling: Reducing the uncertainty on the deformation zone geometry inside the target area would be needed to more firmly define locations of the suitable deposition volumes. There is substantial uncertainty in the Discrete Fracture Network model. Further reduction of the uncertainties, if needed, would probably only be possible from the underground, detailed investigation phase. Efforts need also be spent on improving the DFN-modelling. There are assumptions made in current models that could be challenged and there seems to be room for better use of the borehole information. It is particularly important to

  6. The Quantum Description of BF Model in Superspace

    Directory of Open Access Journals (Sweden)

    Manoj Kumar Dwivedi

    2018-01-01

    Full Text Available We consider the BRST symmetric four-dimensional BF theory, a topological theory, containing antisymmetric tensor fields in Landau gauge and extend the BRST symmetry by introducing a shift symmetry to it. Within this formulation, the antighost fields corresponding to shift symmetry coincide with antifields of standard field/antifield formulation. Furthermore, we provide a superspace description for the BF model possessing extended BRST and extended anti-BRST transformations.

  7. Description of deformed nuclei in the sdg boson model

    International Nuclear Information System (INIS)

    Li, S.C.; Kuyucak, S.

    1996-01-01

    We present a study of deformed nuclei in the framework of the sdg interacting boson model utilizing both numerical diagonalization and analytical 1/N expansion techniques. The focus is on the description of high-spin states which have recently become computationally accessible through the use of computer algebra in the 1/N expansion formalism. A systematic study is made of high-spin states in rare-earth and actinide nuclei. (orig.)

  8. Projected shell model description of N = 114 superdeformed isotone nuclei

    International Nuclear Information System (INIS)

    Guo, R S; Chen, L M; Chou, C H

    2006-01-01

    A systematic description of the yrast superdeformed (SD) bands in N 114, Z = 80-84 isotone nuclei using the projected shell model is presented. The calculated γ-ray energies, moment of inertia and M1 transitions are compared with the data for which spin is assigned. Excellent agreement with the available data for all isotones is obtained. The calculated electromagnetic properties provide a microscopic understanding of those measured nuclei. Some predictions in superdeformed nuclei are also discussed

  9. Description of deformed nuclei in the sdg boson model

    Energy Technology Data Exchange (ETDEWEB)

    Li, S.C. [Australian National Univ., Canberra, ACT (Australia). Research School of Physical Sciences; Kuyucak, S. [Australian National Univ., Canberra, ACT (Australia). Research School of Physical Sciences

    1996-07-15

    We present a study of deformed nuclei in the framework of the sdg interacting boson model utilizing both numerical diagonalization and analytical 1/N expansion techniques. The focus is on the description of high-spin states which have recently become computationally accessible through the use of computer algebra in the 1/N expansion formalism. A systematic study is made of high-spin states in rare-earth and actinide nuclei. (orig.).

  10. Description of deformed nuclei in the sdg boson model

    Science.gov (United States)

    Li, S. C.; Kuyucak, S.

    1996-02-01

    We present a study of deformed nuclei in the framework of the sdg interacting boson model utilizing both numerical diagonalization and analytical {1}/{N} expansion techniques. The focus is on the description of high-spin states which have recently become computationally accessible through the use of computer algebra in the {1}/{N} expansion formalism. A systematic study is made of high-spin states in rare-earth and actinide nuclei.

  11. Hanford Site Composite Analysis Technical Approach Description: Atmospheric Transport Modeling.

    Energy Technology Data Exchange (ETDEWEB)

    Sun, B. [CH2M HILL Plateau Remediation Company, Richland, WA (United States); Lehman, L. L. [CH2M HILL Plateau Remediation Company, Richland, WA (United States)

    2017-10-02

    The U.S. Department of Energy (DOE) in DOE O 435.1 Chg. 1, Radioactive Waste Management, requires the preparation and maintenance of a composite analysis (CA). The primary purpose of the CA is to provide a reasonable expectation that the primary public dose limit is not likely to be exceeded by multiple source terms that may significantly interact with plumes originating at a low-level waste disposal facility. The CA is used to facilitate planning and land use decisions that help assure disposal facility authorization will not result in long-term compliance problems; or, to determine management alternatives, corrective actions or assessment needs, if potential problems are identified.

  12. Geostatistical description of geological heterogeneity in clayey till as input for improved characterization of contaminated sites

    DEFF Research Database (Denmark)

    Kessler, Timo Christian; Klint, K.E.S.; Renard, P.

    2010-01-01

    In low-permeability clay tills subsurface transport is governed by preferential flow in sand lenses and fractures. A proper geological model requires the integration of these features, i.e. the spatial distribution of the geological heterogeneities. Detailed mapping of sand lenses has been done...... at a clay till outcrop in Denmark to characterise the shapes and the spatial variability. Further, geostatistics were applied to simulate the distribution and to develop a heterogeneity model that can be incorporated into an existing geological model of, for example, a contaminated site....

  13. HIGHWAY, a transportation routing model: program description and users' manual

    International Nuclear Information System (INIS)

    Joy, D.S.; Johnson, P.E.; Gibson, S.M.

    1982-12-01

    A computerized transportation routing model has been developed at the Oak Ridge National Laboratory to be used for predicting likely routes for shipping radioactive materials. The HIGHWAY data base is a computerized road atlas containing descriptions of the entire interstate highway system, the federal highway system, and most of the principal state roads. In addition to its prediction of the most likely commercial route, options incorporated in the HIGHWAY model can allow for maximum use of interstate highways or routes that will bypass urbanized areas containing populations > 100,000. The user may also interactively modify the data base to predict routes that bypass any particular state, city, town, or specific highway segment

  14. STAMINA - Model description. Standard Model Instrumentation for Noise Assessments

    NARCIS (Netherlands)

    Schreurs EM; Jabben J; Verheijen ENG; CMM; mev

    2010-01-01

    Deze rapportage beschrijft het STAMINA-model, dat staat voor Standard Model Instrumentation for Noise Assessments en door het RIVM is ontwikkeld. Het instituut gebruikt dit standaardmodel om omgevingsgeluid in Nederland in kaart te brengen. Het model is gebaseerd op de Standaard Karteringsmethode

  15. Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Oak Ridge Gaseous Diffusion Plant Site

    Energy Technology Data Exchange (ETDEWEB)

    1991-09-01

    In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) technology, with the near-term goal to provide the necessary information to make a deployment decision by November 1992. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. A programmatic document for use in screening DOE sites to locate the U-AVLIS production plant was developed and implemented in two parts (Wolsko et al. 1991). The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were then subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the ORGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use, socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3. Following the site description and additional data requirements, Sec. 4 provides a short, qualitative assessment of potential environmental issues. 37 refs., 20 figs., 18 tabs.

  16. Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Oak Ridge Gaseous Diffusion Plant Site

    International Nuclear Information System (INIS)

    1991-09-01

    In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) technology, with the near-term goal to provide the necessary information to make a deployment decision by November 1992. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. A programmatic document for use in screening DOE sites to locate the U-AVLIS production plant was developed and implemented in two parts (Wolsko et al. 1991). The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were then subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the ORGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use, socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3. Following the site description and additional data requirements, Sec. 4 provides a short, qualitative assessment of potential environmental issues. 37 refs., 20 figs., 18 tabs

  17. Summary of repository siting models. Final report

    International Nuclear Information System (INIS)

    Thomas, S.D.; Ross, B.; Mercer, J.W.

    1982-07-01

    This report is the first in a series of reports that will provide critical reviews and summaries of computer programs that can be used to analyze the potential performance of a high-level radioactive waste repository. The computer programs identified address the following phenomena: saturated and unsaturated subsurface flow, heat transport, solute transport, surface water runoff, geomechanical interactions, and geochemical interactions. The report identifies 183 computer programs that can be used to analyze a repository site and provides a summary description of 31 computer programs. The summary descriptions can be used: to assist in code evaluation, to facilitate code comparison, to determine applicability of codes to specific problems, to identify code deficiencies, and to provide a screening mechanism for code selection

  18. Ecosystem site description - an approach to quantify transport and accumulation of matter in a drainage area

    International Nuclear Information System (INIS)

    Soderback, B.; Kautsky, U.; Lindborg, T.

    2004-01-01

    The Swedish Nuclear Fuel and Waste Management Co. (SKB) presently perform site investigations at two sites in Sweden for a future repository of spent nuclear fuel. The safety assessment of a potential repository will, among other methods, use an approach where transport and accumulation of radionuclides is modelled by quantifying the pathways of carbon/nitrogen/phosphorous in the ecosystem. Since water is the most important medium for transportation of matter, the obvious delimitation of an area for quantification of matter transport is the drainage area. This study describes how site-specific data on surface water chemistry and hydrology, measured at several points along the flow paths of a drainage area, can be used to describe and quantify the flow of matter in terms of transport or accumulation. The approach was applied to the drainage area of Lake Eckarfjaerden, investigated as part of the site investigation programme at Forsmark in central Sweden. By using data from inlet and outlet of the lake, together with data from the lake itself, we quantified the flow of matter in the drainage area, and also developed mass-balance budgets for important elements. The results were used to validate process oriented terrestrial and aquatic ecosystem models, developed for the same drainage area in parallel to the present study. In conclusion, applying this approach will contribute substantially to our understanding of the processes controlling transport and accumulation of matter in a drainage area, and thereby reduce the uncertainties in estimating radionuclide flow and consequences to humans and the environment. (author)

  19. Predicate Argument Structure Analysis for Use Case Description Modeling

    Science.gov (United States)

    Takeuchi, Hironori; Nakamura, Taiga; Yamaguchi, Takahira

    In a large software system development project, many documents are prepared and updated frequently. In such a situation, support is needed for looking through these documents easily to identify inconsistencies and to maintain traceability. In this research, we focus on the requirements documents such as use cases and consider how to create models from the use case descriptions in unformatted text. In the model construction, we propose a few semantic constraints based on the features of the use cases and use them for a predicate argument structure analysis to assign semantic labels to actors and actions. With this approach, we show that we can assign semantic labels without enhancing any existing general lexical resources such as case frame dictionaries and design a less language-dependent model construction architecture. By using the constructed model, we consider a system for quality analysis of the use cases and automated test case generation to keep the traceability between document sets. We evaluated the reuse of the existing use cases and generated test case steps automatically with the proposed prototype system from real-world use cases in the development of a system using a packaged application. Based on the evaluation, we show how to construct models with high precision from English and Japanese use case data. Also, we could generate good test cases for about 90% of the real use cases through the manual improvement of the descriptions based on the feedback from the quality analysis system.

  20. THE SHEFFIELD ALCOHOL POLICY MODEL - A MATHEMATICAL DESCRIPTION.

    Science.gov (United States)

    Brennan, Alan; Meier, Petra; Purshouse, Robin; Rafia, Rachid; Meng, Yang; Hill-Macmanus, Daniel; Angus, Colin; Holmes, John

    2014-09-30

    This methodology paper sets out a mathematical description of the Sheffield Alcohol Policy Model version 2.0, a model to evaluate public health strategies for alcohol harm reduction in the UK. Policies that can be appraised include a minimum price per unit of alcohol, restrictions on price discounting, and broader public health measures. The model estimates the impact on consumers, health services, crime, employers, retailers and government tax revenues. The synthesis of public and commercial data sources to inform the model structure is described. A detailed algebraic description of the model is provided. This involves quantifying baseline levels of alcohol purchasing and consumption by age and gender subgroups, estimating the impact of policies on consumption, for example, using evidence on price elasticities of demand for alcohol, quantification of risk functions relating alcohol consumption to harms including 47 health conditions, crimes, absenteeism and unemployment, and finally monetary valuation of the consequences. The results framework, shown for a minimum price per unit of alcohol, has been used to provide policy appraisals for the UK government policy-makers. In discussion and online appendix, we explore issues around valuation and scope, limitations of evidence/data, how the framework can be adapted to other countries and decisions, and ongoing plans for further development. © 2014 The Authors. Health Economics published by John Wiley & Sons Ltd. © 2014 The Authors. Health Economics published by John Wiley & Sons Ltd.

  1. Description of codes and models to be used in risk assessment

    International Nuclear Information System (INIS)

    1991-09-01

    Human health and environmental risk assessments will be performed as part of the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) remedial investigation/feasibility study (RI/FS) activities at the Hanford Site. Analytical and computer encoded numerical models are commonly used during both the remedial investigation (RI) and feasibility study (FS) to predict or estimate the concentration of contaminants at the point of exposure to humans and/or the environment. This document has been prepared to identify the computer codes that will be used in support of RI/FS human health and environmental risk assessments at the Hanford Site. In addition to the CERCLA RI/FS process, it is recommended that these computer codes be used when fate and transport analyses is required for other activities. Additional computer codes may be used for other purposes (e.g., design of tracer tests, location of observation wells, etc.). This document provides guidance for unit managers in charge of RI/FS activities. Use of the same computer codes for all analytical activities at the Hanford Site will promote consistency, reduce the effort required to develop, validate, and implement models to simulate Hanford Site conditions, and expedite regulatory review. The discussion provides a description of how models will likely be developed and utilized at the Hanford Site. It is intended to summarize previous environmental-related modeling at the Hanford Site and provide background for future model development. The modeling capabilities that are desirable for the Hanford Site and the codes that were evaluated. The recommendations include the codes proposed to support future risk assessment modeling at the Hanford Site, and provides the rational for the codes selected. 27 refs., 3 figs., 1 tab

  2. Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Portsmouth Gaseous Diffusion Plant site

    International Nuclear Information System (INIS)

    Marmer, G.J.; Dunn, C.P.; Filley, T.H.; Moeller, K.L.; Pfingston, J.M.; Policastro, A.J.; Cleland, J.H.

    1991-09-01

    Uranium enrichment in the United States has utilized a diffusion process to preferentially enrich the U-235 isotope in the uranium product. In the 1970s, the US Department of Energy (DOE) began investigating more efficient and cost-effective enrichment technologies. In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser isotope Separation (U-AVLIS) technology with the near-term goal to provide the necessary information to make a deployment decision by November 1992. Initial facility operation is anticipated for 1999. A programmatic document for use in screening DOE sites to locate a U-AVLIS production plant was developed and implemented in two parts. The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. The final evaluation, which included sensitivity studies, identified the Oak Ridge Gaseous Diffusion Plant (ORGDP) site, the Paducah Gaseous Diffusion Plant (PGDP) site, and the Portsmouth Gaseous Diffusion Plant (PORTS) site as having significant advantages over the other sites considered. This environmental site description (ESD) provides a detailed description of the PORTS site and vicinity suitable for use in an environmental impact statement (EIS). This report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during site visits. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use. Socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3

  3. Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Portsmouth Gaseous Diffusion Plant site

    Energy Technology Data Exchange (ETDEWEB)

    Marmer, G.J.; Dunn, C.P.; Filley, T.H.; Moeller, K.L.; Pfingston, J.M.; Policastro, A.J.; Cleland, J.H.

    1991-09-01

    Uranium enrichment in the United States has utilized a diffusion process to preferentially enrich the U-235 isotope in the uranium product. In the 1970s, the US Department of Energy (DOE) began investigating more efficient and cost-effective enrichment technologies. In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser isotope Separation (U-AVLIS) technology with the near-term goal to provide the necessary information to make a deployment decision by November 1992. Initial facility operation is anticipated for 1999. A programmatic document for use in screening DOE sites to locate a U-AVLIS production plant was developed and implemented in two parts. The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. The final evaluation, which included sensitivity studies, identified the Oak Ridge Gaseous Diffusion Plant (ORGDP) site, the Paducah Gaseous Diffusion Plant (PGDP) site, and the Portsmouth Gaseous Diffusion Plant (PORTS) site as having significant advantages over the other sites considered. This environmental site description (ESD) provides a detailed description of the PORTS site and vicinity suitable for use in an environmental impact statement (EIS). This report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during site visits. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use. Socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3.

  4. Site-Scale Saturated Zone Flow Model

    International Nuclear Information System (INIS)

    G. Zyvoloski

    2003-01-01

    The purpose of this model report is to document the components of the site-scale saturated-zone flow model at Yucca Mountain, Nevada, in accordance with administrative procedure (AP)-SIII.lOQ, ''Models''. This report provides validation and confidence in the flow model that was developed for site recommendation (SR) and will be used to provide flow fields in support of the Total Systems Performance Assessment (TSPA) for the License Application. The output from this report provides the flow model used in the ''Site-Scale Saturated Zone Transport'', MDL-NBS-HS-000010 Rev 01 (BSC 2003 [162419]). The Site-Scale Saturated Zone Transport model then provides output to the SZ Transport Abstraction Model (BSC 2003 [164870]). In particular, the output from the SZ site-scale flow model is used to simulate the groundwater flow pathways and radionuclide transport to the accessible environment for use in the TSPA calculations. Since the development and calibration of the saturated-zone flow model, more data have been gathered for use in model validation and confidence building, including new water-level data from Nye County wells, single- and multiple-well hydraulic testing data, and new hydrochemistry data. In addition, a new hydrogeologic framework model (HFM), which incorporates Nye County wells lithology, also provides geologic data for corroboration and confidence in the flow model. The intended use of this work is to provide a flow model that generates flow fields to simulate radionuclide transport in saturated porous rock and alluvium under natural or forced gradient flow conditions. The flow model simulations are completed using the three-dimensional (3-D), finite-element, flow, heat, and transport computer code, FEHM Version (V) 2.20 (software tracking number (STN): 10086-2.20-00; LANL 2003 [161725]). Concurrently, process-level transport model and methodology for calculating radionuclide transport in the saturated zone at Yucca Mountain using FEHM V 2.20 are being

  5. Modeling RHIC using the standard machine formal accelerator description

    International Nuclear Information System (INIS)

    Pilat, F.; Trahern, C.G.; Wei, J.

    1997-01-01

    The Standard Machine Format (SMF) is a structured description of accelerator lattices which supports both the hierarchy of beam lines and generic lattice objects as well as those deviations (field errors, alignment efforts, etc.) associated with each component of the as-installed machine. In this paper we discuss the use of SMF to describe the Relativistic Heavy Ion Collider (RHIC) as well as the ancillary data structures (such as field quality measurements) that are necessarily incorporated into the RHIC SMF model. Future applications of SMF are outlined, including its use in the RHIC operational environment

  6. Coarse-grained description of cosmic structure from Szekeres models

    International Nuclear Information System (INIS)

    Sussman, Roberto A.; Gaspar, I. Delgado; Hidalgo, Juan Carlos

    2016-01-01

    We show that the full dynamical freedom of the well known Szekeres models allows for the description of elaborated 3-dimensional networks of cold dark matter structures (over-densities and/or density voids) undergoing ''pancake'' collapse. By reducing Einstein's field equations to a set of evolution equations, which themselves reduce in the linear limit to evolution equations for linear perturbations, we determine the dynamics of such structures, with the spatial comoving location of each structure uniquely specified by standard early Universe initial conditions. By means of a representative example we examine in detail the density contrast, the Hubble flow and peculiar velocities of structures that evolved, from linear initial data at the last scattering surface, to fully non-linear 10–20 Mpc scale configurations today. To motivate further research, we provide a qualitative discussion on the connection of Szekeres models with linear perturbations and the pancake collapse of the Zeldovich approximation. This type of structure modelling provides a coarse grained—but fully relativistic non-linear and non-perturbative —description of evolving large scale cosmic structures before their virialisation, and as such it has an enormous potential for applications in cosmological research

  7. Healing models for organizations: description, measurement, and outcomes.

    Science.gov (United States)

    Malloch, K

    2000-01-01

    Healthcare leaders are continually searching for ways to improve their ability to provide optimal healthcare services, be financially viable, and retain quality caregivers, often feeling like such goals are impossible to achieve in today's intensely competitive environment. Many healthcare leaders intuitively recognize the need for more humanistic models and the probable connection with positive patient outcomes and financial success but are hesitant to make significant changes in their organizations because of the lack of model descriptions or documented recognition of the clinical and financial advantages of humanistic models. This article describes a study that was developed in response to the increasing work in humanistic or healing environment models and the need for validation of the advantages of such models. The healthy organization model, a framework for healthcare organizations that incorporates humanistic healing values within the traditional structure, is presented as a result of the study. This model addresses the importance of optimal clinical services, financial performance, and staff satisfaction. The five research-based organizational components that form the framework are described, and key indicators of organizational effectiveness over a five-year period are presented. The resulting empirical data are strongly supportive of the healing model and reflect positive outcomes for the organization.

  8. FARMLAND: Model description and evaluation of model performance

    International Nuclear Information System (INIS)

    Attwood, C.; Fayers, C.; Mayall, A.; Brown, J.; Simmonds, J.R.

    1996-01-01

    The FARMLAND model was originally developed for use in connection with continuous, routine releases of radionuclides, but because it has many time-dependent features it has been developed further for a single accidental release. The most recent version of FARMLAND is flexible and can be used to predict activity concentrations in food as a function of time after both accidental and routine releases of radionuclides. The effect of deposition at different times of the year can be taken into account. FARMLAND contains a suite of models which simulate radionuclide transfer through different parts of the foodchain. The models can be used in different combinations and offer the flexibility to assess a variety of radiological situations. The main foods considered are green vegetables, grain products, root vegetables, milk, meat and offal from cattle, and meat and offal from sheep. A large variety of elements can be considered although the degree of complexity with which some are modelled is greater than others; isotopes of caesium, strontium and iodine are treated in greatest detail. 22 refs, 12 figs, 10 tabs

  9. FARMLAND: Model description and evaluation of model performance

    Energy Technology Data Exchange (ETDEWEB)

    Attwood, C; Fayers, C; Mayall, A; Brown, J; Simmonds, J R [National Radiological Protection Board, Chilton (United Kingdom)

    1996-09-01

    The FARMLAND model was originally developed for use in connection with continuous, routine releases of radionuclides, but because it has many time-dependent features it has been developed further for a single accidental release. The most recent version of FARMLAND is flexible and can be used to predict activity concentrations in food as a function of time after both accidental and routine releases of radionuclides. The effect of deposition at different times of the year can be taken into account. FARMLAND contains a suite of models which simulate radionuclide transfer through different parts of the foodchain. The models can be used in different combinations and offer the flexibility to assess a variety of radiological situations. The main foods considered are green vegetables, grain products, root vegetables, milk, meat and offal from cattle, and meat and offal from sheep. A large variety of elements can be considered although the degree of complexity with which some are modelled is greater than others; isotopes of caesium, strontium and iodine are treated in greatest detail. 22 refs, 12 figs, 10 tabs.

  10. Interim oceanographic description of the North-East Atlantic site for the disposal of low-level radioactive waste

    International Nuclear Information System (INIS)

    Gurbutt, P.A.; Dickson, R.R.

    1983-01-01

    Within the terms of the Surveillance Mechanism for Sea Dumping of Radioactive Wastes, NEA is requested to assess the suitability of dumping sites proposed by Participating countries and to keep under review those previously thought suitable. The aim of this volume is to provide a further interim description of the North-East Atlantic dumpsite itself. Quantities of known wastes dumpings are summarized. A review of the available data on sediment distribution in the area is presented. The flow field at the site is described so that an experiment to determine the influence on the deep flow of large scale topographic features at the dumpsite. The tide gauge results are briefly presented. The state of knowledge of the hydrographic and chemical conditions prior to 1977 is reviewed; recent results are added. The results of the radioactivity determination in the surface layer (3cm thick) of box cored sediments and the vertical radioactivity profiles are presented in tables. Some results on adsorption and geochemical partitioning of long-lived radionuclides on dumpsite sediments are briefly reviewed. Biological studies have been undertaken: concentration of radionuclides in biological materials, radiation effects on the dumpsite fauna. A dose-limit (critical group) calculation model is presented. Collective dose commitment and mass transfer are briefly discussed. The concentration of radionuclides in sediments and some organisms of the Bay of Biscay has been evaluated. Some isopycnal data for the eastern Atlantic, windstress and stratification are briefly mentioned

  11. Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Paducah Gaseous Diffusion Plant site

    Energy Technology Data Exchange (ETDEWEB)

    Marmer, G.J.; Dunn, C.P.; Moeller, K.L.; Pfingston, J.M.; Policastro, A.J.; Yuen, C.R.; Cleland, J.H. (ed.)

    1991-09-01

    Uranium enrichment in the United States has utilized a diffusion process to preferentially enrich the U-235 isotope in the uranium product. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. The U-235 atoms are ionized when precisely tuned laser light -- of appropriate power, spectral, and temporal characteristics -- illuminates the uranium vapor and selectively photoionizes the U-235 isotope. A programmatic document for use in screening DOE site to locate a U-AVLIS production plant was developed and implemented in two parts. The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the PGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. 65 refs., 15 tabs.

  12. Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Paducah Gaseous Diffusion Plant site

    International Nuclear Information System (INIS)

    Marmer, G.J.; Dunn, C.P.; Moeller, K.L.; Pfingston, J.M.; Policastro, A.J.; Yuen, C.R.; Cleland, J.H.

    1991-09-01

    Uranium enrichment in the United States has utilized a diffusion process to preferentially enrich the U-235 isotope in the uranium product. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. The U-235 atoms are ionized when precisely tuned laser light -- of appropriate power, spectral, and temporal characteristics -- illuminates the uranium vapor and selectively photoionizes the U-235 isotope. A programmatic document for use in screening DOE site to locate a U-AVLIS production plant was developed and implemented in two parts. The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the PGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. 65 refs., 15 tabs

  13. Model and information abstraction for description-driven systems

    International Nuclear Information System (INIS)

    Estrella, F.; McClatchey, R.; Kovacs, Z.; Goff, J.-M.L.

    2001-01-01

    A crucial factor in the creation of adaptable systems dealing with changing requirements is the suitability of the underlying technology in allowing the evolution of the system. A reflective system utilizes an open architecture where implicit system aspects are reified to become explicit first-class (meta-data) objects. These implicit system aspects are often fundamental structures which are inaccessible and immutable, and their reification as meta-data objects can serve as the basis for changes and extensions to the system, making it self-describing. To address the evolvability issue, the author proposes a reflective architecture based on two orthogonal abstractions-model abstraction and information abstraction. In this architecture the modeling abstractions allow for the separation of the description meta-data from the system aspects they represent so that they can be managed and versioned independently, asynchronously and explicitly

  14. Global warming description using Daisyworld model with greenhouse gases.

    Science.gov (United States)

    Paiva, Susana L D; Savi, Marcelo A; Viola, Flavio M; Leiroz, Albino J K

    2014-11-01

    Daisyworld is an archetypal model of the earth that is able to describe the global regulation that can emerge from the interaction between life and environment. This article proposes a model based on the original Daisyworld considering greenhouse gases emission and absorption, allowing the description of the global warming phenomenon. Global and local analyses are discussed evaluating the influence of greenhouse gases in the planet dynamics. Numerical simulations are carried out showing the general qualitative behavior of the Daisyworld for different scenarios that includes solar luminosity variations and greenhouse gases effect. Nonlinear dynamics perspective is of concern discussing a way that helps the comprehension of the global warming phenomenon. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  15. Watershed modeling at the Savannah River Site.

    Energy Technology Data Exchange (ETDEWEB)

    Vache, Kellie [Oregon State University

    2015-04-29

    The overall goal of the work was the development of a watershed scale model of hydrological function for application to the US Department of Energy’s (DOE) Savannah River Site (SRS). The primary outcomes is a grid based hydrological modeling system that captures near surface runoff as well as groundwater recharge and contributions of groundwater to streams. The model includes a physically-based algorithm to capture both evaporation and transpiration from forestland.

  16. A computationally efficient description of heterogeneous freezing: A simplified version of the Soccer ball model

    Science.gov (United States)

    Niedermeier, Dennis; Ervens, Barbara; Clauss, Tina; Voigtländer, Jens; Wex, Heike; Hartmann, Susan; Stratmann, Frank

    2014-01-01

    In a recent study, the Soccer ball model (SBM) was introduced for modeling and/or parameterizing heterogeneous ice nucleation processes. The model applies classical nucleation theory. It allows for a consistent description of both apparently singular and stochastic ice nucleation behavior, by distributing contact angles over the nucleation sites of a particle population assuming a Gaussian probability density function. The original SBM utilizes the Monte Carlo technique, which hampers its usage in atmospheric models, as fairly time-consuming calculations must be performed to obtain statistically significant results. Thus, we have developed a simplified and computationally more efficient version of the SBM. We successfully used the new SBM to parameterize experimental nucleation data of, e.g., bacterial ice nucleation. Both SBMs give identical results; however, the new model is computationally less expensive as confirmed by cloud parcel simulations. Therefore, it is a suitable tool for describing heterogeneous ice nucleation processes in atmospheric models.

  17. 3D modeling of buildings outstanding sites

    CERN Document Server

    Héno, Rapha?le

    2014-01-01

    Conventional topographic databases, obtained by capture on aerial or spatial images provide a simplified 3D modeling of our urban environment, answering the needs of numerous applications (development, risk prevention, mobility management, etc.). However, when we have to represent and analyze more complex sites (monuments, civil engineering works, archeological sites, etc.), these models no longer suffice and other acquisition and processing means have to be implemented. This book focuses on the study of adapted lifting means for "notable buildings". The methods tackled in this book cover las

  18. Discrete-Feature Model Implementation of SDM-Site Forsmark

    International Nuclear Information System (INIS)

    Geier, Joel

    2010-03-01

    A discrete-feature model (DFM) was implemented for the Forsmark repository site based on the final site descriptive model from surface based investigations. The discrete-feature conceptual model represents deformation zones, individual fractures, and other water-conducting features around a repository as discrete conductors surrounded by a rock matrix which, in the present study, is treated as impermeable. This approximation is reasonable for sites in crystalline rock which has very low permeability, apart from that which results from macroscopic fracturing. Models are constructed based on the geological and hydrogeological description of the sites and engineering designs. Hydraulic heads and flows through the network of water-conducting features are calculated by the finite-element method, and are used in turn to simulate migration of non-reacting solute by a particle-tracking method, in order to estimate the properties of pathways by which radionuclides could be released to the biosphere. Stochastic simulation is used to evaluate portions of the model that can only be characterized in statistical terms, since many water-conducting features within the model volume cannot be characterized deterministically. Chapter 2 describes the methodology by which discrete features are derived to represent water-conducting features around the hypothetical repository at Forsmark (including both natural features and features that result from the disturbance of excavation), and then assembled to produce a discrete-feature network model for numerical simulation of flow and transport. Chapter 3 describes how site-specific data and repository design are adapted to produce the discrete-feature model. Chapter 4 presents results of the calculations. These include utilization factors for deposition tunnels based on the emplacement criteria that have been set forth by the implementers, flow distributions to the deposition holes, and calculated properties of discharge paths as well as

  19. Discrete-Feature Model Implementation of SDM-Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Geier, Joel (Clearwater Hardrock Consulting, Corvallis, OR (United States))

    2010-03-15

    A discrete-feature model (DFM) was implemented for the Forsmark repository site based on the final site descriptive model from surface based investigations. The discrete-feature conceptual model represents deformation zones, individual fractures, and other water-conducting features around a repository as discrete conductors surrounded by a rock matrix which, in the present study, is treated as impermeable. This approximation is reasonable for sites in crystalline rock which has very low permeability, apart from that which results from macroscopic fracturing. Models are constructed based on the geological and hydrogeological description of the sites and engineering designs. Hydraulic heads and flows through the network of water-conducting features are calculated by the finite-element method, and are used in turn to simulate migration of non-reacting solute by a particle-tracking method, in order to estimate the properties of pathways by which radionuclides could be released to the biosphere. Stochastic simulation is used to evaluate portions of the model that can only be characterized in statistical terms, since many water-conducting features within the model volume cannot be characterized deterministically. Chapter 2 describes the methodology by which discrete features are derived to represent water-conducting features around the hypothetical repository at Forsmark (including both natural features and features that result from the disturbance of excavation), and then assembled to produce a discrete-feature network model for numerical simulation of flow and transport. Chapter 3 describes how site-specific data and repository design are adapted to produce the discrete-feature model. Chapter 4 presents results of the calculations. These include utilization factors for deposition tunnels based on the emplacement criteria that have been set forth by the implementers, flow distributions to the deposition holes, and calculated properties of discharge paths as well as

  20. Testing Pearl Model In Three European Sites

    Science.gov (United States)

    Bouraoui, F.; Bidoglio, G.

    The Plant Protection Product Directive (91/414/EEC) stresses the need of validated models to calculate predicted environmental concentrations. The use of models has become an unavoidable step before pesticide registration. In this context, European Commission, and in particular DGVI, set up a FOrum for the Co-ordination of pes- ticide fate models and their USe (FOCUS). In a complementary effort, DG research supported the APECOP project, with one of its objective being the validation and im- provement of existing pesticide fate models. The main topic of research presented here is the validation of the PEARL model for different sites in Europe. The PEARL model, actually used in the Dutch pesticide registration procedure, was validated in three well- instrumented sites: Vredepeel (the Netherlands), Brimstone (UK), and Lanna (Swe- den). A step-wise procedure was used for the validation of the PEARL model. First the water transport module was calibrated, and then the solute transport module, using tracer measurements keeping unchanged the water transport parameters. The Vrede- peel site is characterised by a sandy soil. Fourteen months of measurements were used for the calibration. Two pesticides were applied on the site: bentazone and etho- prophos. PEARL predictions were very satisfactory for both soil moisture content, and pesticide concentration in the soil profile. The Brimstone site is characterised by a cracking clay soil. The calibration was conducted on a time series measurement of 7 years. The validation consisted in comparing predictions and measurement of soil moisture at different soil depths, and in comparing the predicted and measured con- centration of isoproturon in the drainage water. The results, even if in good agreement with the measuremens, highlighted the limitation of the model when the preferential flow becomes a dominant process. PEARL did not reproduce well soil moisture pro- file during summer months, and also under-predicted the arrival of

  1. Developing ecological site and state-and-transition models for grazed riparian pastures at Tejon Ranch, California

    Science.gov (United States)

    Felix P. Ratcliff; James Bartolome; Michele Hammond; Sheri Spiegal; Michael White

    2015-01-01

    Ecological site descriptions and associated state-and-transition models are useful tools for understanding the variable effects of management and environment on range resources. Models for woody riparian sites have yet to be fully developed. At Tejon Ranch, in the southern San Joaquin Valley of California, we are using ecological site theory to investigate the role of...

  2. Perspective in site-suitability modelling

    International Nuclear Information System (INIS)

    Chartier, M.

    1989-01-01

    The Steering Committee for Nuclear Energy of the OECD-Nuclear Energy Agency decided in April 1981 to set up a Co-ordinated Research and Environmental Surveillance Programme relevant to sea disposal of radioactive waste (CRESP) with the objective of reinforcing the scientific basis of future assessments of the continued suitability of the North-East Atlantic site to be made under the NEA Multilateral Consultation and Surveillance Mechanism. A major component of the initial CRESP plan was the development of a site-specific model to predict radionuclide transfer rates and patterns in the marine environment. A new general approach to the design of such a site-specific model is discussed.Although this approach originates partly from methodologies presented in GESAMP partly from an approach put forward within the NEA Seabed Working Group/Geochemical and Physical Oceanography Task Group and partly from methods previously agreed by the CRESP Modelling Task Group, the modelling philosophy developed in the text expressed the personal viewpoint of the author. This text aims to state the present methods of modelling the marine transfer of radionuclides and to anticipate modelling strategies which may be adopted in the future (in France for example), but it does not necessarily meet present NEA viewpoints and the philosophy of other CRESP participating countries

  3. Semantic description of three-dimensional models of Bologna porches

    Directory of Open Access Journals (Sweden)

    Massimo Ballabeni

    2015-07-01

    Full Text Available The study is part of a broader search coordinated by the Department of Architecture of the University of Bologna, the Cineca and the city of Bologna for the nomination of the city porticoes in the UNESCO World Heritage Site. The study describes, first, the problems and the methods adopted for the survey, the numerical modeling and visualization of the arcades models. In addition, the paper aims to describe a method for the semantic studying of the porticoes architecture and the segmentation of the models. The goal is also to establish an integrated approach to the semantic cataloguing of the Bologna arcades based on historical, material, formal, dimensional and theoretical data, and to make this information easily readable and communicable.

  4. Translation of a High-Level Temporal Model into Lower Level Models: Impact of Modelling at Different Description Levels

    DEFF Research Database (Denmark)

    Kraft, Peter; Sørensen, Jens Otto

    2001-01-01

    The paper attempts theoretically to clarify the interrelation between various levels of descriptions used in the modelling and the programming of information systems. We suggest an analysis where we characterise the description levels with respect to how precisely they may handle information abou...... and other textual models. We also consider the aptness of models that include procedural mechanisms such as active and object databases...

  5. Comparison of Transcription Factor Binding Site Models

    KAUST Repository

    Bhuyan, Sharifulislam

    2012-05-01

    Modeling of transcription factor binding sites (TFBSs) and TFBS prediction on genomic sequences are important steps to elucidate transcription regulatory mechanism. Dependency of transcription regulation on a great number of factors such as chemical specificity, molecular structure, genomic and epigenetic characteristics, long distance interaction, makes this a challenging problem. Different experimental procedures generate evidence that DNA-binding domains of transcription factors show considerable DNA sequence specificity. Probabilistic modeling of TFBSs has been moderately successful in identifying patterns from a family of sequences. In this study, we compare performances of different probabilistic models and try to estimate their efficacy over experimental TFBSs data. We build a pipeline to calculate sensitivity and specificity from aligned TFBS sequences for several probabilistic models, such as Markov chains, hidden Markov models, Bayesian networks. Our work, containing relevant statistics and evaluation for the models, can help researchers to choose the most appropriate model for the problem at hand.

  6. Construction of Site Risk Model using Individual Unit Risk Model in a NPP Site

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Ho Gon; Han, Sang Hoon [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    Since Fukushima accident, strong needs to estimate site risk has been increased to identify the possibility of re-occurrence of such a tremendous disaster and prevent such a disaster. Especially, in a site which has large fleet of nuclear power plants, reliable site risk assessment is very emergent to confirm the safety. In Korea, there are several nuclear power plant site which have more than 6 NPPs. In general, risk model of a NPP in terms of PSA is very complicated and furthermore, it is expected that the site risk model is more complex than that. In this paper, the method for constructing site risk model is proposed by using individual unit risk model. Procedure for the development of site damage (risk) model was proposed in the present paper. Since the site damage model is complicated in the sense of the scale of the system and dependency of the components of the system, conventional method may not be applicable in many side of the problem.

  7. Morphological description and comparison of the dental remains from Atapuerca-Sima de los Huesos site (Spain).

    Science.gov (United States)

    Martinón-Torres, María; Bermúdez de Castro, José María; Gómez-Robles, Aida; Prado-Simón, Leyre; Arsuaga, Juan Luis

    2012-01-01

    The systematic excavation of the Sima de los Huesos (SH) site in Sierra de Atapuerca (Burgos, Spain) has yielded the largest hominin collection worldwide for the Middle Pleistocene. The dental sample now consists of more than 500 teeth that provide exceptional opportunities to define the dental morphological pattern of a Middle Pleistocene population as well as develop hypotheses about the origins of the Neanderthals. The dental collection has now increased to over 533 specimens (525 permanent and 8 deciduous teeth), necessitating new morphological assessments. Thus, we present a detailed morphological description of the SH permanent dentition recovered up to 2007, accomplishing comparisons with European Middle Pleistocene hominins, Neanderthals, and early and contemporary Homo sapiens. We find that SH dentitions present all the morphological traits that, either in their degree of expression, frequency, or particular combination, are usually considered as typical of Homo neanderthalensis. This study ratifies the deep roots of the Neanderthal lineage in the Middle Pleistocene of Europe. In addition, SH teeth are morphologically "more Neanderthal" than other penecontemporaneous Middle Pleistocene samples such as Mauer or Arago, and even more derived than some classic Neanderthal samples. Thus, our study would not sustain the linearity of the accretion process hypothesized for the origins of the Neanderthals, and we suggest that other evolutionary models and scenarios should be explored for the Middle and Upper Pleistocene of Europe. We propose that more than one hominin lineage may have coexisted during the Middle Pleistocene in Europe. Copyright © 2011 Elsevier Ltd. All rights reserved.

  8. The shell model. Towards a unified description of nuclear structure

    Energy Technology Data Exchange (ETDEWEB)

    Poves, Alfredo [Departamento de Fisica Teorica, Universidad Autonoma Cantoblanco, 28049 - Madrid (Spain); Collaboration: La Direction des Sciences de la Matiere du CEA (FR); Le Fonds National de la Recherche Scientifique de Belgique (BE)

    1998-12-31

    In this series of lectures we present the foundations of the spherical shell model that we treat as an approximation to the exact solution of the full secular problem. We introduce the notions of valence space, effective interaction and effective operator. We analyse the structure of the realistic effective interactions, identifying their monopole part with the spherical mean field. The multipole Hamiltonian is shown to have a universal (simple) form that includes pairing (isovector and isoscalar), quadrupole, octupole, deca-pole, and ({sigma}{center_dot}{tau})({sigma}{center_dot}{tau}). We describe the methods of resolution of the secular problem, in particular the Lanczos method. The model is applied to the description of nuclear deformation and its relationship with the deformed mean field theories is studied. We propose a new symmetry, `quasi`-SU3, to understand deformation in the spherical basis. Finally, we discuss the domain of nuclei very far from the valley of {beta} stability, addressing the vanishing of some magic closures that can be explained in terms of intruder states. (author) 53 refs., 20 figs., 3 tabs.

  9. The shell model. Towards a unified description of nuclear structure

    International Nuclear Information System (INIS)

    Poves, Alfredo

    1998-01-01

    In this series of lectures we present the foundations of the spherical shell model that we treat as an approximation to the exact solution of the full secular problem. We introduce the notions of valence space, effective interaction and effective operator. We analyse the structure of the realistic effective interactions, identifying their monopole part with the spherical mean field. The multipole Hamiltonian is shown to have a universal (simple) form that includes pairing (isovector and isoscalar), quadrupole, octupole, deca-pole, and (σ·τ)(σ·τ). We describe the methods of resolution of the secular problem, in particular the Lanczos method. The model is applied to the description of nuclear deformation and its relationship with the deformed mean field theories is studied. We propose a new symmetry, 'quasi'-SU3, to understand deformation in the spherical basis. Finally, we discuss the domain of nuclei very far from the valley of β stability, addressing the vanishing of some magic closures that can be explained in terms of intruder states. (author)

  10. Hanford site as it relates to an alternative site for the Waste Isolation Pilot Plant: an environmental description

    Energy Technology Data Exchange (ETDEWEB)

    Fecht, K.R. (ed.)

    1978-12-01

    The use of basalt at Hanford as an alternative for the Waste Isolation Pilot Plant (WIPP) would require that the present Basalt Waste Isolation Program (BWIP) at Hanford be expanded to incorporate the planned WIPP functions, namely the permanent storage of transuranic (TRU) wastes. This report discusses: program costs, demography, ecology, climatology, physiography, hydrology, geology, seismology, and historical and archeological sites. (DLC)

  11. Hanford site as it relates to an alternative site for the Waste Isolation Pilot Plant: an environmental description

    International Nuclear Information System (INIS)

    Fecht, K.R.

    1978-12-01

    The use of basalt at Hanford as an alternative for the Waste Isolation Pilot Plant (WIPP) would require that the present Basalt Waste Isolation Program (BWIP) at Hanford be expanded to incorporate the planned WIPP functions, namely the permanent storage of transuranic (TRU) wastes. This report discusses: program costs, demography, ecology, climatology, physiography, hydrology, geology, seismology, and historical and archeological sites

  12. Discourse Model Representation of Referential and Attributive Descriptions.

    Science.gov (United States)

    Onishi, Kristine H.; Murphy, Gregory L.

    2002-01-01

    Manipulated shared knowledge and focus on specific entities, the verb in the sentence, and whether the description was definite or indefinite. Each factor influenced interpretation of the description. Confirmed that changing verbs alone affected reference choice. Indicated that both referentially and attributively introduced entities are…

  13. Site-Specific Seismic Site Response Model for the Waste Treatment Plant, Hanford, Washington

    Energy Technology Data Exchange (ETDEWEB)

    Rohay, Alan C.; Reidel, Steve P.

    2005-02-24

    This interim report documents the collection of site-specific geologic and geophysical data characterizing the Waste Treatment Plant site and the modeling of the site-specific structure response to earthquake ground motions.

  14. CSOIL 2000 an exposure model for human risk assessment of soil contamination. A model description

    NARCIS (Netherlands)

    Brand E; Otte PF; Lijzen JPA; LER

    2007-01-01

    This RIVM description of the CSOIL 2000 model deals, for the first time, with all aspects of the model. CSOIL 2000 can be used to derive intervention values. Intervention values are calculated for contaminated soil and represent a measure for determining when contaminated soil needs to be

  15. Wind Atlas for South Africa (WASA) Station and Site Description Report

    DEFF Research Database (Denmark)

    Mortensen, Niels Gylling; Hansen, Jens Carsten; Kelly, Mark C.

    As part of the “Wind Atlas for South Africa” project, site inspection trips were carried out by the Council for Scientific and Industrial Research (CSIR) and Risø DTU in April and June of 2011. A total of 10 sites featuring instrumented 60-m masts were visited; the present report summarises...

  16. Process Description for the Retrieval of Earth Covered Transuranic (TRU) Waste Containers at the Hanford Site

    International Nuclear Information System (INIS)

    DEROSA, D.C.

    2000-01-01

    This document describes process and operational options for retrieval of the contact-handled suspect transuranic waste drums currently stored below grade in earth-covered trenches at the Hanford Site. Retrieval processes and options discussed include excavation, container retrieval, venting, non-destructive assay, criticality avoidance, incidental waste handling, site preparation, equipment, and shipping

  17. Process Description for the Retrieval of Earth Covered Transuranic (TRU) Waste Containers at the Hanford Site

    Energy Technology Data Exchange (ETDEWEB)

    DEROSA, D.C.

    2000-01-13

    This document describes process and operational options for retrieval of the contact-handled suspect transuranic waste drums currently stored below grade in earth-covered trenches at the Hanford Site. Retrieval processes and options discussed include excavation, container retrieval, venting, non-destructive assay, criticality avoidance, incidental waste handling, site preparation, equipment, and shipping.

  18. Descriptions and models of safety functions - a prestudy

    International Nuclear Information System (INIS)

    Harms-Ringdahl, L.

    1999-09-01

    A study has been made with the focus on different theories and applications concerning 'safety functions' and 'barriers'. In this report, a safety function is defined as a technical or organisational function with the aim to reduce probability and/or consequences associated with a hazard. The study contains a limited review of practice and theories related to safety, with a focus on applications from nuclear and industrial safety. The study is based on a literature review and interviews. A summary has been made of definitions and terminology, which shows a large variation. E.g. 'barrier' can have a precise physical and technical meaning, or it can include human, technical and organisational elements. Only a few theoretical models describing safety functions have been found. One section of the report summarises problems related to safety issues and procedures. They concern errors in procedure design and user compliance. A proposal for describing and structuring safety functions has been made. Dimensions in a description could be degree of abstraction, systems level, the different parts of the function, etc. A model for safety functions has been proposed, which includes the division of a safety function in a number connected 'safety function elements'. One conclusion is that there is a potential for improving theories and tools for safety work and procedures. Safety function could be a useful concept in such a development, and advantages and disadvantages with this is discussed. If further work should be done, it is recommended that this is made as a combination of theoretical analysis and case studies

  19. Data model description for the DESCARTES and CIDER codes

    International Nuclear Information System (INIS)

    Miley, T.B.; Ouderkirk, S.J.; Nichols, W.E.; Eslinger, P.W.

    1993-01-01

    The primary objective of the Hanford Environmental Dose Reconstruction (HEDR) Project is to estimate the radiation dose that individuals could have received as a result of emissions since 1944 from the US Department of Energy's (DOE) Hanford Site near Richland, Washington. One of the major objectives of the HEDR Project is to develop several computer codes to model the airborne releases. transport and envirorunental accumulation of radionuclides resulting from Hanford operations from 1944 through 1972. In July 1992, the HEDR Project Manager determined that the computer codes being developed (DESCARTES, calculation of environmental accumulation from airborne releases, and CIDER, dose calculations from environmental accumulation) were not sufficient to create accurate models. A team of HEDR staff members developed a plan to assure that computer codes would meet HEDR Project goals. The plan consists of five tasks: (1) code requirements definition. (2) scoping studies, (3) design specifications, (4) benchmarking, and (5) data modeling. This report defines the data requirements for the DESCARTES and CIDER codes

  20. Description and Rationale for the Planning, Monitoring, and Implementation (PMI) Model: Description.

    Science.gov (United States)

    Ford, Valeria A.

    The design of the Planning, Monitoring, and Implementation Model (PMI) and the aspects of the model that make it useful in public schools are the topics of this paper. After the objectives of a program or operation have been identified, the model specifies three additional pieces of information that are needed for an evaluation: inputs, processes,…

  1. Classification and Probabilistic Description of a Sand Site Based on CPTU

    DEFF Research Database (Denmark)

    Lauridsen, Kristoffer; Andersen, Sarah; Ibsen, Lars Bo

    2012-01-01

    A sand site at the harbour of Frederikshavn, where numerous cone penetration tests (CPT) have been conducted, is considered. Methods for interpreting CPT´s and strength parameters are assessed, and compared to the results of a set of laboratory tests. The raw cone penetration measurements...... at varying locations the correlation between these are compared. Thereby assessing how the correlation at the sand site is affected by spatial distances....

  2. The Moulded Site Data (MSD) wind correlation method: description and assessment

    Energy Technology Data Exchange (ETDEWEB)

    King, C.; Hurley, B.

    2004-12-01

    The long-term wind resource at a potential windfarm site may be estimated by correlating short-term on-site wind measurements with data from a regional meteorological station. A correlation method developed at Airtricity is described in sufficient detail to be reproduced. An assessment of its performance is also described; the results may serve as a guide to expected accuracy when using the method as part of an annual electricity production estimate for a proposed windfarm. (Author)

  3. The infinite sites model of genome evolution.

    Science.gov (United States)

    Ma, Jian; Ratan, Aakrosh; Raney, Brian J; Suh, Bernard B; Miller, Webb; Haussler, David

    2008-09-23

    We formalize the problem of recovering the evolutionary history of a set of genomes that are related to an unseen common ancestor genome by operations of speciation, deletion, insertion, duplication, and rearrangement of segments of bases. The problem is examined in the limit as the number of bases in each genome goes to infinity. In this limit, the chromosomes are represented by continuous circles or line segments. For such an infinite-sites model, we present a polynomial-time algorithm to find the most parsimonious evolutionary history of any set of related present-day genomes.

  4. Interim oceanographic description of the North-East-Atlantic site for the disposal of low-level radioactive waste. Vol. 2

    International Nuclear Information System (INIS)

    Dickson, R.R.; Gurbutt, P.A.; Kershaw, P.J.

    1986-01-01

    The NEA Co-ordinated Research and Environmental Surveillance Programme (CRESP) related to sea disposal of radioactive waste was started in 1981 following a recommendation of the Group of experts convened every five years by NEA to review the continued suitability of the dumping site for radioactive waste in the North-East Atlantic. The objective of CRESP is to increase the available scientific data base related to the oceanographic and biological characteristics of the dump site and elaborate a site specific model of the transfers of radionuclides to human populations. Volume one of the ''Interim Oceanographic Description of the North-East Atlantic Site for the Disposal of Low-Level Radioactive Waste'' was published in early 1983. It was an attempt to identify remaining gaps in current knowledge of conditions at the site and relate these conditions to the physical environment of the North-East Atlantic Ocean as a whole. The amount of data obtained by the CRESP Programme is now sufficient to justify publication of this second volume. Scientists present results of research which is of direct relevance to a better assessment of the impact from dumping radioactive waste in the North-East Atlantic, in particular an evaluation of the potential radiation doses to man. These two volumes represent part of the scientific contribution of the CRESP Programme to the 1985 Review of the Continued Suitability of the North-East Atlantic dump site

  5. Protein structure modelling and evaluation based on a 4-distance description of side-chain interactions

    Directory of Open Access Journals (Sweden)

    Inbar Yuval

    2010-07-01

    Full Text Available Abstract Background Accurate evaluation and modelling of residue-residue interactions within and between proteins is a key aspect of computational structure prediction including homology modelling, protein-protein docking, refinement of low-resolution structures, and computational protein design. Results Here we introduce a method for accurate protein structure modelling and evaluation based on a novel 4-distance description of residue-residue interaction geometry. Statistical 4-distance preferences were extracted from high-resolution protein structures and were used as a basis for a knowledge-based potential, called Hunter. We demonstrate that 4-distance description of side chain interactions can be used reliably to discriminate the native structure from a set of decoys. Hunter ranked the native structure as the top one in 217 out of 220 high-resolution decoy sets, in 25 out of 28 "Decoys 'R' Us" decoy sets and in 24 out of 27 high-resolution CASP7/8 decoy sets. The same concept was applied to side chain modelling in protein structures. On a set of very high-resolution protein structures the average RMSD was 1.47 Å for all residues and 0.73 Å for buried residues, which is in the range of attainable accuracy for a model. Finally, we show that Hunter performs as good or better than other top methods in homology modelling based on results from the CASP7 experiment. The supporting web site http://bioinfo.weizmann.ac.il/hunter/ was developed to enable the use of Hunter and for visualization and interactive exploration of 4-distance distributions. Conclusions Our results suggest that Hunter can be used as a tool for evaluation and for accurate modelling of residue-residue interactions in protein structures. The same methodology is applicable to other areas involving high-resolution modelling of biomolecules.

  6. MIRAGE: Model description and evaluation of aerosols and trace gases

    Science.gov (United States)

    Easter, Richard C.; Ghan, Steven J.; Zhang, Yang; Saylor, Rick D.; Chapman, Elaine G.; Laulainen, Nels S.; Abdul-Razzak, Hayder; Leung, L. Ruby; Bian, Xindi; Zaveri, Rahul A.

    2004-10-01

    colleagues are probably too high. Surface-level dimethyl sulfide (DMS) is ˜40% higher than observed, and the seasonal cycle shows too much DMS in local winter, partially caused by neglect of oxidation by NO3. Surface-level MSA at marine locations is ˜80% higher than observed, also attributed to insufficient wet removal. Surface-level BC is ˜50% lower than observed in the United States and ˜40% lower than observed globally. Treating BC as initially hydrophobic would lessen this bias. Surface-level organic matter is lower than observed in the United States, similar to BC, but shows no bias in the global comparison. Surface-level sea salt concentrations are ˜30% lower than observed, partly caused by low temporal variance of the model's 10 m wind speeds. Submicrometer sea salt is strongly underestimated by the emissions parameterization. Dust concentrations are within a factor of 3 at most sites but tend to be lower than observed, primarily because of neglect of very large particles and underestimation of emissions and vertical transport under high-wind conditions. Accumulation and Aitken mode number concentrations and mean sizes at the surface over ocean, and condensation nuclei concentrations aloft over the Pacific, are in fair agreement with observations. Concentrations over land are generally higher than observations, with mean sizes correspondingly lower than observations, especially at some European locations. Increasing the assumed size of emitted particles produces better agreement at the surface over land, and reducing the particle nucleation rate improves the agreement aloft over land.

  7. Description of a Multipurpose Processing and Storage Complex for the Hanford Site's radioactive material

    International Nuclear Information System (INIS)

    Nyman, D.H.; Wolfe, B.A.; Hoertkorn, T.R.

    1993-05-01

    The mission of the US Department of Energy's (DOE) Hanford Site has changed from defense nuclear materials production to that of waste management/disposal and environmental restoration. ne Multipurpose Processing and Storage Complex (MPSC) is being designed to process discarded waste tank internal hardware contaminated with mixed wastes, failed melters from the vitrification plant, and other Hanford Site high-level solid waste. The MPSC also will provide interim storage of other radioactive materials (irradiated fuel, canisters of vitrified high-level waste [HLW], special nuclear material [SNM], and other designated radioactive materials)

  8. Integrating textual and model-based process descriptions for comprehensive process search

    NARCIS (Netherlands)

    Leopold, Henrik; van der Aa, Han; Pittke, Fabian; Raffel, Manuel; Mendling, Jan; Reijers, Hajo A.

    2016-01-01

    Documenting business processes using process models is common practice in many organizations. However, not all process information is best captured in process models. Hence, many organizations complement these models with textual descriptions that specify additional details. The problem with this

  9. SITE-94. Discrete-feature modelling of the Aespoe site: 2. Development of the integrated site-scale model

    Energy Technology Data Exchange (ETDEWEB)

    Geier, J.E. [Golder Associates AB, Uppsala (Sweden)

    1996-12-01

    A 3-dimensional, discrete-feature hydrological model is developed. The model integrates structural and hydrologic data for the Aespoe site, on scales ranging from semi regional fracture zones to individual fractures in the vicinity of the nuclear waste canisters. Hydrologic properties of the large-scale structures are initially estimated from cross-hole hydrologic test data, and automatically calibrated by numerical simulation of network flow, and comparison with undisturbed heads and observed drawdown in selected cross-hole tests. The calibrated model is combined with a separately derived fracture network model, to yield the integrated model. This model is partly validated by simulation of transient responses to a long-term pumping test and a convergent tracer test, based on the LPT2 experiment at Aespoe. The integrated model predicts that discharge from the SITE-94 repository is predominantly via fracture zones along the eastern shore of Aespoe. Similar discharge loci are produced by numerous model variants that explore uncertainty with regard to effective semi regional boundary conditions, hydrologic properties of the site-scale structures, and alternative structural/hydrological interpretations. 32 refs.

  10. SITE-94. Discrete-feature modelling of the Aespoe site: 2. Development of the integrated site-scale model

    International Nuclear Information System (INIS)

    Geier, J.E.

    1996-12-01

    A 3-dimensional, discrete-feature hydrological model is developed. The model integrates structural and hydrologic data for the Aespoe site, on scales ranging from semi regional fracture zones to individual fractures in the vicinity of the nuclear waste canisters. Hydrologic properties of the large-scale structures are initially estimated from cross-hole hydrologic test data, and automatically calibrated by numerical simulation of network flow, and comparison with undisturbed heads and observed drawdown in selected cross-hole tests. The calibrated model is combined with a separately derived fracture network model, to yield the integrated model. This model is partly validated by simulation of transient responses to a long-term pumping test and a convergent tracer test, based on the LPT2 experiment at Aespoe. The integrated model predicts that discharge from the SITE-94 repository is predominantly via fracture zones along the eastern shore of Aespoe. Similar discharge loci are produced by numerous model variants that explore uncertainty with regard to effective semi regional boundary conditions, hydrologic properties of the site-scale structures, and alternative structural/hydrological interpretations. 32 refs

  11. Description of age, sex and site distribution of large bowel cancer in ...

    African Journals Online (AJOL)

    Aims/Objective: To determine the distribution of bowel cancer with special emphasis on age, sex and site. Methods: One hundred and sixty cases of histologically confirmed large bowel cancers at Jos University Teaching Hospital between January 1991 – December 2000 were reviewed. The records were collected from the ...

  12. Site descriptions of environmental restoration units at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    Kuhaida, A.J. Jr.; Parker, A.F.

    1997-02-01

    This report provides summary information on Oak Ridge National Laboratory (ORNL) Environmental Restoration (ER) sites as listed in the Oak Ridge Reservation Federal Facility Agreement (FFA), dated January 1, 1992, Appendix C. The Oak Ridge National Laboratory was built in 1943 as part of the World War II Manhattan Project. The original mission of ORNL was to produce and chemically separate the first gram-quantities of plutonium as part of the national effort to produce the atomic bomb. The current mission of ORNL is to provide applied research and development in support of the U.S. Department of Energy (DOE) programs in nuclear fusion and fission, energy conservation, fossil fuels, and other energy technologies and to perform basic scientific research in selected areas of the physical, life, and environmental sciences. ER is also tasked with clean up or mitigation of environmental impacts resulting from past waste management practices on portions of the approximately 37,000 acres within the Oak Ridge Reservation (ORR). Other installations located within the ORR are the Gaseous Diffusion Plant (K-25) and the Y-12 plant. The remedial action strategy currently integrates state and federal regulations for efficient compliance and approaches for both investigations and remediation efforts on a Waste Area Grouping (WAG) basis. As defined in the ORR FFA Quarterly Report July - September 1995, a WAG is a grouping of potentially contaminated sites based on drainage area and similar waste characteristics. These contaminated sites are further divided into four categories based on existing information concerning whether the data are generated for scoping or remedial investigation (RI) purposes. These areas are as follows: (1) Operable Units (OU); (2) Characterization Areas (CA); (3) Remedial Site Evaluation (RSE) Areas; and (4) Removal Site Evaluation (RmSE) Areas.

  13. Description logics with approximate definitions precise modeling of vague concepts

    NARCIS (Netherlands)

    Schlobach, Stefan; Klein, Michel; Peelen, Linda

    2007-01-01

    We extend traditional Description Logics (DL) with a simple mechanism to handle approximate concept definitions in a qualitative way. Often, for example in medical applications, concepts are not definable in a crisp way but can fairly exhaustively be constrained through a particular sub- and a

  14. Risk methodology for geologic disposal of radioactive waste: model description and user manual for Pathways model

    International Nuclear Information System (INIS)

    Helton, J.C.; Kaestner, P.C.

    1981-03-01

    A model for the environmental movement and human uptake of radionuclides is presented. This model is designated the Pathways-to-Man Model and was developed as part of a project funded by the Nuclear Regulatory Commission to design a methodology to assess the risk associated with the geologic disposal of high-level radioactive waste. The Pathways-to-Man Model is divided into two submodels. One of these, the Environmental Transport Model, represents the long-term distribution and accumulation of radionuclides in the environment. This model is based on a mixed-cell approach and describes radionuclide movement with a system of linear differential equations. The other, the Transport-to-Man Model, represents the movement of radionuclides from the environment to man. This model is based on concentration ratios. General descriptions of these models are provided in this report. Further, documentation is provided for the computer program which implements the Pathways Model

  15. Idaho National Laboratory Ten-Year Site Plan Project Description Document

    Energy Technology Data Exchange (ETDEWEB)

    Not Listed

    2012-03-01

    This document describes the currently active and proposed infrastructure projects listed in Appendix B of the Idaho National Laboratory 2013-2022 Ten Year Site Plan (DOE/ID-11449). It was produced in accordance with Contract Data Requirements List I.06. The projects delineated in this document support infrastructure needs at INL's Research and Education Campus, Materials and Fuels Complex, Advanced Test Reactor Complex and the greater site-wide area. The projects provide critical infrastructure needed to meet current and future INL opereational and research needs. Execution of these projects will restore, rebuild, and revitalize INL's physical infrastructure; enhance program execution, and make a significant contribution toward reducing complex-wide deferred maintenance.

  16. Multivariate approach to assessing ecotoxicity on abandoned oil refinery environments: Study site description

    International Nuclear Information System (INIS)

    Lochmiller, R.L.; Yates, G.W.

    1993-01-01

    Ecology risk assessment requires a clear understanding of how complex mixtures of environmental contaminants impact terrestrial ecosystems. This assessment process could be more universally applied to terrestrial ecosystems with better defined assay systems for evaluating impacts of exposure on organisms, populations, and communities. The authors objective was to define and assess the efficacy of a battery of assays incorporating both standard biological toxicity test and in situ biomonitors for evaluating ecological risks on terrestrial environments contaminated with complex mixtures of petrochemicals on a 160 acre abandoned oil refinery in central Oklahoma. Three suspected contaminated and three uncontaminated reference sites were selected for intensive study. Habitat on each study site is representative of disturbed tall-grass prairie and supports dense, diverse small mammal communities. Soil samples were subjected to aqueous extraction and resulting leachates analyzed for heavy metals, selected ions, and organics. Analytical results support their initial assessment that toxic study sites were contaminated with complex mixtures including lead, zinc, arsenic, chloride, sulfate, potassium, and complex mixtures of polar and non-polar organics

  17. Environmental impact assessment of decommissioning treatment about radioactive model plant waste ore storage site

    International Nuclear Information System (INIS)

    Bei Xinyu

    2012-01-01

    Aiming at decommissioning treatment project of radioactive model plant waste ore storage site, based on the detailed investigations of source terms and project description, systematic environmental impacts have been identified. The environmental impacts both during decommissioning treatment, radioactive waste transportation and after treatment are assessed. Some specific environmental protection measures are proposed so as to minimize the adverse environmental impacts. (author)

  18. Modeling of a sedimentary rock alternative for the siting of the radioactive waste disposal system

    International Nuclear Information System (INIS)

    Fuentes, Nestor O.

    2007-01-01

    Here are described the main concepts, the approximations, and all those simulation aspects that characterize the modeling performed using the unsaturated saturated approach for porous media. The objective of this work is to obtain a generic description of a sedimentary rock soil as an alternative site for the low and intermediate level radioactive waste disposal system. (author) [es

  19. Description of source term data on contaminated sites and buildings compiled for the waste management programmatic environmental impact statement (WMPEIS)

    International Nuclear Information System (INIS)

    Short, S.M.; Smith, D.E.; Hill, J.G.; Lerchen, M.E.

    1995-10-01

    The U.S. Department of Energy (DOE) and its predecessor agencies have historically had responsibility for carrying out various national missions primarily related to nuclear weapons development and energy research. Recently, these missions have been expanded to include remediation of sites and facilities contaminated as a result of past activities. In January 1990, the Secretary of Energy announced that DOE would prepare a Programmatic Environmental Impact Statement on the DOE's environmental restoration and waste management program; the primary focus was the evaluation of (1) strategies for conducting remediation of all DOE contaminated sites and facilities and (2) potential configurations for waste management capabilities. Several different environmental restoration strategies were identified for evaluation, ranging from doing no remediation to strategies where the level of remediation was driven by such factors as final land use and health effects. A quantitative assessment of the costs and health effects of remediation activities and residual contamination levels associated with each remediation strategy was made. These analyses required that information be compiled on each individual contaminated site and structure located at each DOE installation and that the information compiled include quantitative measurements and/or estimates of contamination levels and extent of contamination. This document provides a description of the types of information and data compiled for use in the analyses. Also provided is a description of the database used to manage the data, a detailed discussion of the methodology and assumptions used in compiling the data, and a summary of the data compiled into the database as of March 1995. As of this date, over 10,000 contaminated sites and structures and over 8,000 uncontaminated structures had been identified across the DOE complex of installations

  20. INTRA/Mod3.2. Manual and Code Description. Volume I - Physical Modelling

    International Nuclear Information System (INIS)

    Andersson, Jenny; Edlund, O.; Hermann, J.; Johansson, Lise-Lotte

    1999-01-01

    The INTRA Manual consists of two volumes. Volume I of the manual is a thorough description of the code INTRA, the Physical modelling of INTRA and the ruling numerical methods and volume II, the User's Manual is an input description. This document, the Physical modelling of INTRA, contains code characteristics, integration methods and applications

  1. INTRA/Mod3.2. Manual and Code Description. Volume I - Physical Modelling

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Jenny; Edlund, O; Hermann, J; Johansson, Lise-Lotte

    1999-01-01

    The INTRA Manual consists of two volumes. Volume I of the manual is a thorough description of the code INTRA, the Physical modelling of INTRA and the ruling numerical methods and volume II, the User`s Manual is an input description. This document, the Physical modelling of INTRA, contains code characteristics, integration methods and applications

  2. Description of INR-Pitesti own strategy for on site radioactive solid waste storage concepts

    International Nuclear Information System (INIS)

    Tuturici, I.L.; Toma, V.; Bujoreanu, D.; Prava, M.

    1993-01-01

    The Post Irradiation Examination Laboratory (PIEL) produces and will produce the majority of institute's alpha-contaminated solid radioactive waste, generated by the process of examination of irradiated CANDU-600 type nuclear fuel. The wastes will be divided into three categories: low-level, medium-level, and high-level general process trash (LLGPT, MLGPT, and HLGPT). The paper describes the strategy adopted for immobilization, conditioning and on-site long-term storage of these wastes. The proposed strategy is based on the best experience acquired by other nuclear centers, confronted with same problems. (Author)

  3. Hanford Site Composite Analysis Technical Approach Description: Groundwater Pathway Dose Calculation.

    Energy Technology Data Exchange (ETDEWEB)

    Morgans, D. L. [CH2M Hill Plateau Remediation Company, Richland, WA (United States); Lindberg, S. L. [Intera Inc., Austin, TX (United States)

    2017-09-20

    The purpose of this technical approach document (TAD) is to document the assumptions, equations, and methods used to perform the groundwater pathway radiological dose calculations for the revised Hanford Site Composite Analysis (CA). DOE M 435.1-1, states, “The composite analysis results shall be used for planning, radiation protection activities, and future use commitments to minimize the likelihood that current low-level waste disposal activities will result in the need for future corrective or remedial actions to adequately protect the public and the environment.”

  4. Electronic structure description of the cis-MoOS unit in models for molybdenum hydroxylases.

    Science.gov (United States)

    Doonan, Christian J; Rubie, Nick D; Peariso, Katrina; Harris, Hugh H; Knottenbelt, Sushilla Z; George, Graham N; Young, Charles G; Kirk, Martin L

    2008-01-09

    The molybdenum hydroxylases catalyze the oxidation of numerous aromatic heterocycles and simple organics and, unlike other hydroxylases, utilize water as the source of oxygen incorporated into the product. The electronic structures of the cis-MoOS units in CoCp2[TpiPrMoVOS(OPh)] and TpiPrMoVIOS(OPh) (TpiPr = hydrotris(3-isopropylpyrazol-1-yl)borate), new models for molybdenum hydroxylases, have been studied in detail using S K-edge X-ray absorption spectroscopy, vibrational spectroscopy, and detailed bonding calculations. The results show a highly delocalized Mo=S pi* LUMO redox orbital that is formally Mo(dxy) with approximately 35% sulfido ligand character. Vibrational spectroscopy has been used to quantitate Mo-Ssulfido bond order changes in the cis-MoOS units as a function of redox state. Results support a redox active molecular orbital that has a profound influence on MoOS bonding through changes to the relative electro/nucleophilicity of the terminal sulfido ligand accompanying oxidation state changes. The bonding description for these model cis-MoOS systems supports enzyme mechanisms that are under orbital control and dominantly influenced by the unique electronic structure of the cis-MoOS site. The electronic structure of the oxidized enzyme site is postulated to play a role in polarizing a substrate carbon center for nucleophilic attack by metal activated water and acting as an electron sink in the two-electron oxidation of substrates.

  5. Model of Team Organization and Behavior and Team Description Method

    Science.gov (United States)

    1984-10-01

    PERFORMING ORG& REPORT’ NUMBER 7.AUTHIOR(&) 0. CONTRACT OR GRANT NUMOSR(ej J. Thomas Roth Rohn J. Hritz HDA 903-81-C-0198: VEa Donald W. McGill 9...team descriptions are included, acid procedures for data recording are provided. 4q-4 4 iv, G OP S• . . • ,," $1 . . ’ __ _ _ _ ’ / . • , Utilization...Listing of thi! number acid identification of the roles adopted by team members in the actual team structure, along with KOS and primary equipment

  6. Architecture Descriptions. A Contribution to Modeling of Production System Architecture

    DEFF Research Database (Denmark)

    Jepsen, Allan Dam; Hvam, Lars

    a proper understanding of the architecture phenomenon and the ability to describe it in a manner that allow the architecture to be communicated to and handled by stakeholders throughout the company. Despite the existence of several design philosophies in production system design such as Lean, that focus...... a diverse set of stakeholder domains and tools in the production system life cycle. To support such activities, a contribution is made to the identification and referencing of production system elements within architecture descriptions as part of the reference architecture framework. The contribution...

  7. Palaeohydrogeological modelling for potential future repository sites

    International Nuclear Information System (INIS)

    2001-01-01

    In order to consider the future behaviour of a groundwater system over time scales of relevance to repository safety assessment, it is necessary to develop an understanding of how the groundwater system has changed over time. This can be done through studying the palaeohydrogeology of the groundwater system. The EQUIP project (Evidence from Quaternary Infills for Palaeohydrogeology) set out to develop and evaluate methodologies for obtaining palaeohydrogeological information from fracture infill minerals formed under past groundwater conditions. EQUIP was a collaborative project funded jointly by the European Commission and, in the UK, by the Environment Agency and UK Nirex Limited. The project also involved partners in Finland, France, Spain and Sweden. The fracture infill material chosen for this investigation was calcite, because its reactions in low temperature groundwater environments are fairly well understood and it is fairly ubiquitous in both crystalline and sedimentary rocks. In addition, geochemical modelling suggests that plausible time scales for growth of individual calcite crystals are in the range 10 to 10,000 years, so they may accumulate a record of groundwater evolution over periods of significant climate change. The project was based on four sites, having different climate histories and geological conditions, at which drillcore samples of the deep crystalline rocks, accompanied by hydrogeological and hydrochemical data for the current groundwater conditions, were already available. The principal study sites were Olkiluoto in Finland, Aspo/Laxemar in Sweden, Sellafield in the UK and Vienne in France. The results of the study focus on the morphology and bulk compositions of calcite, compositional zoning of calcite crystals and compositions of fluid inclusions. There are systematic variations in bulk compositions with depth and also in discrete compositional fluctuations (or zones) in individual calcite crystals. These are inferred to reflect

  8. Depth and stratigraphy of Quaternary deposits. Preliminary site description Laxemar subarea - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Nyman, Helena [SWECO Position AB, Stockholm (Sweden)

    2005-09-01

    This report aims at describing the modelled Quaternary deposits (QD) depth according to six layers with different geological and hydrological properties in the Simpevarp regional model area. The program used in the modelling of QD depths is the GeoEditor, which is an ArcView3.3-extension. The input data used in the model consist of 102 boreholes and 328 observation points. As input is also a large number of observation points interpreted from geophysical investigations used; 1,087 points based on refraction seismic measurements (distributed in 31 profiles), 22 points from electrical soundings (VES) and 19,237 points from seismic and sediment echo sounding data. The outer part of the area has a low data density. Some of the used points are generally not very deep and do not describe the actual bedrock elevation. They do, however, describe the minimum QD depth at each location. A detailed topographical Digital Elevation Model (DEM), the maps of Quaternary deposits and outcrops were also used. The model is based on a three-layer-principle where each layer can be given similar properties. The uppermost layer, Z1, has been influenced by the impact from surface processes, e.g. roots and biological activity. The bottom layer, Z3, is characterized by contact with the bedrock and is corresponding to a till layer. The middle layer, Z2, is corresponding to a clay layer and assumed to have different hydraulic qualities than Z1 and Z3. Besides those layers, another three layers are also modelled; M1 corresponds to a peat layer, M2 answers to a glaciofluvial sediment layer and M3 corresponds to a layer with artificial fill. All layers can have thickness zero. The resulting model clearly shows the valleys with thicker depths of QD, surrounded by areas with thinner or no depths. The esker near Faarbo (Tunaaasen) is also distinctly marked in the south-western area. The northern and central part of the model area are characterized by numerous bedrock outcrops. The maximum depth of

  9. Mass discharge estimation from contaminated sites: Multi-model solutions for assessment of conceptual uncertainty

    DEFF Research Database (Denmark)

    Thomsen, Nanna Isbak; Troldborg, Mads; McKnight, Ursula S.

    2012-01-01

    site. The different conceptual models consider different source characterizations and hydrogeological descriptions. The idea is to include a set of essentially different conceptual models where each model is believed to be realistic representation of the given site, based on the current level...... the appropriate management option. The uncertainty of mass discharge estimates depends greatly on the extent of the site characterization. A good approach for uncertainty estimation will be flexible with respect to the investigation level, and account for both parameter and conceptual model uncertainty. We...... propose a method for quantifying the uncertainty of dynamic mass discharge estimates from contaminant point sources on the local scale. The method considers both parameter and conceptual uncertainty through a multi-model approach. The multi-model approach evaluates multiple conceptual models for the same...

  10. Field-based description of rhyolite lava flows of the Calico Hills Formation, Nevada National Security Site, Nevada

    Science.gov (United States)

    Sweetkind, Donald S.; Bova, Shiera C.

    2015-01-01

    Contaminants introduced into the subsurface of Pahute Mesa, Nevada National Security Site, by underground nuclear testing are of concern to the U.S. Department of Energy and regulators responsible for protecting human health and safety. The potential for contaminant movement away from the underground test areas at Pahute Mesa and into the accessible environment is greatest by groundwater transport through fractured volcanic rocks. The 12.9 Ma (mega-annums, million years) Calico Hills Formation, which consists of a mixture of rhyolite lava flows and intercalated nonwelded and bedded tuff and pyroclastic flow deposits, occurs in two areas of the Nevada National Security Site. One area is north of the Rainier Mesa caldera, buried beneath Pahute Mesa, and serves as a heterogeneous volcanic-rock aquifer but is only available to study through drilling and is not described in this report. A second accumulation of the formation is south of the Rainier Mesa caldera and is exposed in outcrop along the western boundary of the Nevada National Security Site at the Calico Hills near Yucca Mountain. These outcrops expose in three dimensions an interlayered sequence of tuff and lava flows similar to those intercepted in the subsurface beneath Pahute Mesa. Field description and geologic mapping of these exposures described lithostratigraphic variations within lava flows and assisted in, or at least corroborated, conceptualization of the rhyolite lava-bearing parts of the formation.

  11. A descriptive study of pressure pain threshold at 2 standardized sites in people with acute or subacute neck pain.

    Science.gov (United States)

    Walton, David M; Macdermid, Joy C; Nielson, Warren; Teasell, Robert W; Nailer, Tamara; Maheu, Phillippe

    2011-09-01

    Cross-sectional convenience sample. To describe the distribution of scores for pressure pain threshold (PPT) at 2 standardized testing sites in people with neck pain of less than 90 days' duration: the angle of the upper trapezius and the belly of the tibialis anterior. A secondary objective was to identify important influences on PPT. PPT may be a valuable assessment and prognostic indicator for people with neck pain. However, to facilitate interpretation of scores, knowledge of means and variance for the target population, as well as factors that might influence scores, is needed. Participants were recruited from community-based physiotherapy clinics and underwent PPT testing using a digital algometer and standardized protocol. Descriptive statistics (mean, standard deviations, quartiles, skewness, and kurtosis) were calculated for the 2 sites. Simple bivariate tests of association were conducted to explore potential moderators. A positively skewed distribution was described for the 2 standardized sites. Significant moderators were sex (male higher than female), age (r = 0.22), and self-reported pain intensity (r = -0.24). Neither litigation status nor most symptomatic/least symptomatic side influenced PPT. This manuscript presents information regarding the expected scores for PPT testing in people with acute or subacute neck pain. Clinicians can compare the results of individual patients against these population values, and researchers can incorporate the significant confounders of age, sex, and self-reported pain intensity into future research designs.

  12. Context discovery using attenuated Bloom codes: model description and validation

    NARCIS (Netherlands)

    Liu, F.; Heijenk, Geert

    A novel approach to performing context discovery in ad-hoc networks based on the use of attenuated Bloom filters is proposed in this report. In order to investigate the performance of this approach, a model has been developed. This document describes the model and its validation. The model has been

  13. A descriptive model of information problem solving while using internet

    NARCIS (Netherlands)

    Brand-Gruwel, Saskia; Wopereis, Iwan; Walraven, Amber

    2009-01-01

    This paper presents the IPS-I-model: a model that describes the process of information problem solving (IPS) in which the Internet (I) is used to search information. The IPS-I-model is based on three studies, in which students in secondary and (post) higher education were asked to solve information

  14. Description of Success: A Four-Teacher Instructional Model.

    Science.gov (United States)

    Reed, Dianne

    This study described a four-teacher instructional model in operation at an elementary school, noting the perceptions of fourth grade students, parents, and teachers regarding the model. The model encompassed teaming, block scheduling, departmentalization of subjects, integrated/interdisciplinary instruction, and in-depth instruction in each…

  15. Thermodynamic approach to rheological modeling and simulations at the configuration space level of description

    NARCIS (Netherlands)

    Jongschaap, R.J.J.; Denneman, A.I.M.; Denneman, A.I.M.; Conrads, W.

    1997-01-01

    The so-called matrix model is a general thermodynamic framework for microrheological modeling. This model has already been proven to be applicable for a wide class of systems, in particular to models formulated at the configuration tensor level of description. For models formulated at the

  16. Description of Muzzle Blast by Modified Ideal Scaling Models

    Directory of Open Access Journals (Sweden)

    Kevin S. Fansler

    1998-01-01

    Full Text Available Gun blast data from a large variety of weapons are scaled and presented for both the instantaneous energy release and the constant energy deposition rate models. For both ideal explosion models, similar amounts of data scatter occur for the peak overpressure but the instantaneous energy release model correlated the impulse data significantly better, particularly for the region in front of the gun. Two parameters that characterize gun blast are used in conjunction with the ideal scaling models to improve the data correlation. The gun-emptying parameter works particularly well with the instantaneous energy release model to improve data correlation. In particular, the impulse, especially in the forward direction of the gun, is correlated significantly better using the instantaneous energy release model coupled with the use of the gun-emptying parameter. The use of the Mach disc location parameter improves the correlation only marginally. A predictive model is obtained from the modified instantaneous energy release correlation.

  17. TERNIRBU: Description of model and individual evaluation of model performance for scenario S

    International Nuclear Information System (INIS)

    Kanyar, B.; Fueloep, N.

    1996-01-01

    The compartmental model used is realized as a procedure of the general purpose code TAMDYN for simulation, sensitivity and uncertainty calculations of dynamic models. More details of the model structure and parameters are given in the description of the VAMP MP Scenario CB. The difference between the climate in Finland and Central Bohemia was taken into consideration by shifting the seasonality function with 12 days' according to the weekly average temperature. The lake system and the contamination of fishes was simulated by the model SIRATEC used and validated in the BIOMOVS Scenario A5. The model was extended to two fish-compartments for roach and pike ones as a catanary system. For simulations the code TAMDYN was used. The doses were estimated from the time integrated concentrations of the proper components multiplied by the dose conversion factor. 4 figs

  18. Bioenergy crop models: Descriptions, data requirements and future challenges

    Energy Technology Data Exchange (ETDEWEB)

    Nair, S. Surendran [University of Tennessee, Knoxville (UTK); Kang, Shujiang [ORNL; Zhang, Xuesong [Pacific Northwest National Laboratory (PNNL); Miguez, Fernando [Iowa State University; Izaurralde, Dr. R. Cesar [Pacific Northwest National Laboratory (PNNL); Post, Wilfred M [ORNL; Dietze, Michael [University of Illinois, Urbana-Champaign; Lynd, L. [Dartmouth College; Wullschleger, Stan D [ORNL

    2012-01-01

    Field studies that address the production of lignocellulosic biomass as a source of renewable energy provide critical data for the development of bioenergy crop models. A literature survey revealed that 14 models have been used for simulating bioenergy crops including herbaceous and woody bioenergy crops, and for crassulacean acid metabolism (CAM) crops. These models simulate field-scale production of biomass for switchgrass (ALMANAC, EPIC, and Agro-BGC), miscanthus (MISCANFOR, MISCANMOD, and WIMOVAC), sugarcane (APSIM, AUSCANE, and CANEGRO), and poplar and willow (SECRETS and 3PG). Two models are adaptations of dynamic global vegetation models and simulate biomass yields of miscanthus and sugarcane at regional scales (Agro-IBIS and LPJmL). Although it lacks the complexity of other bioenergy crop models, the environmental productivity index (EPI) is the only model used to estimate biomass production of CAM (Agave and Opuntia) plants. Except for the EPI model, all models include representations of leaf area dynamics, phenology, radiation interception and utilization, biomass production, and partitioning of biomass to roots and shoots. A few models simulate soil water, nutrient, and carbon cycle dynamics, making them especially useful for assessing the environmental consequences (e.g., erosion and nutrient losses) associated with the large-scale deployment of bioenergy crops. The rapid increase in use of models for energy crop simulation is encouraging; however, detailed information on the influence of climate, soils, and crop management practices on biomass production is scarce. Thus considerable work remains regarding the parameterization and validation of process-based models for bioenergy crops; generation and distribution of high-quality field data for model development and validation; and implementation of an integrated framework for efficient, high-resolution simulations of biomass production for use in planning sustainable bioenergy systems.

  19. Grimsel Test Site: modelling radionuclide migration field experiments

    International Nuclear Information System (INIS)

    Heer, W.; Hadermann, J.

    1994-09-01

    In the migration field experiments at Nagra's Grimsel Test Site, the processes of nuclide transport through a well defined fractured shear-zone in crystalline rock are being investigated. For these experiments, model calculations have been performed to obtain indications on validity and limitation of the model applied and the data deduced under field conditions. The model consists of a hydrological part, where the dipole flow fields of the experiments are determined, and a nuclide transport part, where the flow field driven nuclide propagation through the shear-zone is calculated. In addition to the description of the model, analytical expressions are given to guide the interpretation of experimental results. From the analysis of experimental breakthrough curves for conservative uranine, weakly sorbing sodium and more stronger sorbing strontium tracers, the following main results can be derived: i) The model is able to represent the breakthrough curves of the migration field experiments to a high degree of accuracy, ii) The process of matrix diffusion is manifest through the tails of the breakthrough curves decreasing with time as t -3/2 and through the special shape of the tail ends, both confirmed by the experiments, iii) For nuclide sorbing rapidly, not too strongly, linearly, and exhibiting a reversible cation exchange process on fault gouge, the laboratory sorption coefficient can reasonably well be extrapolated to field conditions. Adequate care in selecting and preparing the rock samples is, of course, a necessary requirement. Using the parameters determined in the previous analysis, predictions are made for experiments in a smaller an faster flow field. For conservative uranine and weakly sorbing sodium, the agreement of predicted and measured breakthrough curves is good, for the more stronger sorbing strontium reasonable, confirming that the model describes the main nuclide transport processes adequately. (author) figs., tabs., 29 refs

  20. Descriptive documentation for New Mexico uranium milling model

    International Nuclear Information System (INIS)

    Bonem, G.; Livevano, R.J.

    1981-01-01

    The New Mexico Uranium Milling Model is a linear programming model. It can demonstrate how cost minimizing management can reduce the costs of milling uranium subject to a series of environmental, resource, and technological constraints. For example, if 15,000 tons were the targeted level of milling output, the model would provide the minimum cost of this production level, given certain levels of environmental, fuel, water, and technological constraints. The model was developed to allow state policymakers to assess the uranium industry from various standpoints. Through the use of the model, state policymakers can determine the effects of air and water discharge standards and limited capital availability on: milling costs of production; uses of electricity, fuel, and water; and levels of air and water emissions. The model covers the following: process technologies which are acid leach and carbonate leach; raw materials mix; air and water discharges; residual treatment process; and plant types

  1. Stochastic description of heterogeneities of permeability within groundwater flow models

    International Nuclear Information System (INIS)

    Cacas, M.C.; Lachassagne, P.; Ledoux, E.; Marsily, G. de

    1991-01-01

    In order to model radionuclide migration in the geosphere realistically at the field scale, the hydrogeologist needs to be able to simulate groundwater flow in heterogeneous media. Heterogeneity of the medium can be described using a stochastic approach, that affects the way in which a flow model is formulated. In this paper, we discuss the problems that we have encountered in modelling both continuous and fractured media. The stochastic approach leads to a methodology that enables local measurements of permeability to be integrated into a model which gives a good prediction of groundwater flow on a regional scale. 5 Figs.; 8 Refs

  2. The SocioEconomic Analysis of Repository Siting (SEARS): Technical Documentation: Volume 1, Description of code and files

    International Nuclear Information System (INIS)

    Kiel, B.; Parpia, B.; Murdock, S.; Hamm, R.; Fannin, D.; Ransom-Nelson, W.; Leistritz, F.L.

    1985-05-01

    The SEARS Model is a comprehensive, highly flexible, user-oriented system for projecting economic, demographic, public service and fiscal impacts of a high-level nuclear waste repository siting. Both baseline and project-related impact projections may be performed for regions, counties, municipalities, and school districts. It is an interactive APL model requiring comprehensive data bases and parameters to generate the outputs desired. 75 refs., 24 figs., 14 tabs

  3. LPJmL4 - a dynamic global vegetation model with managed land - Part 1: Model description

    Science.gov (United States)

    Schaphoff, Sibyll; von Bloh, Werner; Rammig, Anja; Thonicke, Kirsten; Biemans, Hester; Forkel, Matthias; Gerten, Dieter; Heinke, Jens; Jägermeyr, Jonas; Knauer, Jürgen; Langerwisch, Fanny; Lucht, Wolfgang; Müller, Christoph; Rolinski, Susanne; Waha, Katharina

    2018-04-01

    This paper provides a comprehensive description of the newest version of the Dynamic Global Vegetation Model with managed Land, LPJmL4. This model simulates - internally consistently - the growth and productivity of both natural and agricultural vegetation as coherently linked through their water, carbon, and energy fluxes. These features render LPJmL4 suitable for assessing a broad range of feedbacks within and impacts upon the terrestrial biosphere as increasingly shaped by human activities such as climate change and land use change. Here we describe the core model structure, including recently developed modules now unified in LPJmL4. Thereby, we also review LPJmL model developments and evaluations in the field of permafrost, human and ecological water demand, and improved representation of crop types. We summarize and discuss LPJmL model applications dealing with the impacts of historical and future environmental change on the terrestrial biosphere at regional and global scale and provide a comprehensive overview of LPJmL publications since the first model description in 2007. To demonstrate the main features of the LPJmL4 model, we display reference simulation results for key processes such as the current global distribution of natural and managed ecosystems, their productivities, and associated water fluxes. A thorough evaluation of the model is provided in a companion paper. By making the model source code freely available at https://gitlab.pik-potsdam.de/lpjml/LPJmL" target="_blank">https://gitlab.pik-potsdam.de/lpjml/LPJmL, we hope to stimulate the application and further development of LPJmL4 across scientific communities in support of major activities such as the IPCC and SDG process.

  4. A Descriptive Study of Differing School Health Delivery Models

    Science.gov (United States)

    Becker, Sherri I.; Maughan, Erin

    2017-01-01

    The purpose of this exploratory qualitative study was to identify and describe emerging models of school health services. Participants (N = 11) provided information regarding their models in semistructured phone interviews. Results identified a variety of funding sources as well as different staffing configurations and supervision. Strengths of…

  5. Summary description of the RELAP5 Koeberg-1 simulation model

    International Nuclear Information System (INIS)

    D'Arcy, A.J.

    1990-11-01

    The main features of the RELAP5 code and the model are summarized. The model has been quality-assured in accordance with a QA programme used in the Reactor Theory Group of the Atomic Energy Corporation of SA Ltd. The RELAP5 code is based on a non-homogeneous, non-equilibrium model for the two-phase system that is solved by a fast, partially implicit numerical scheme. The objective of the development effort from the outset has been to produce a code that includes important first-order effects necessary for accurate prediction of system transients, but is sufficiently simple and cost-effective so that parametric or sensitivity studies are possible. The code includes many generic component models from which general systems can be simulated. Special process models are included for effects such as form losses, flow at an abrupt area change, branching, choked flow, boron tracking and a non-condensible gas. The RELAP5 modelling and computational aspects covered are: hydrodynamic models, constitutive package, special process models, and user conveniences. 25 tabs., 8 figs., 17 refs

  6. "Growing trees backwards": Description of a stand reconstruction model

    Science.gov (United States)

    Jonathan D. Bakker; Andrew J. Sanchez Meador; Peter Z. Fule; David W. Huffman; Margaret M. Moore

    2008-01-01

    We describe an individual-tree model that uses contemporary measurements to "grow trees backward" and reconstruct past tree diameters and stand structure in ponderosa pine dominated stands of the Southwest. Model inputs are contemporary structural measurements of all snags, logs, stumps, and living trees, and radial growth measurements, if available. Key...

  7. MELMRK 2.0: A description of computer models and results of code testing

    International Nuclear Information System (INIS)

    Wittman, R.S.; Denny, V.; Mertol, A.

    1992-01-01

    An advanced version of the MELMRK computer code has been developed that provides detailed models for conservation of mass, momentum, and thermal energy within relocating streams of molten metallics during meltdown of Savannah River Site (SRS) reactor assemblies. In addition to a mechanistic treatment of transport phenomena within a relocating stream, MELMRK 2.0 retains the MOD1 capability for real-time coupling of the in-depth thermal response of participating assembly heat structure and, further, augments this capability with models for self-heating of relocating melt owing to steam oxidation of metallics and fission product decay power. As was the case for MELMRK 1.0, the MOD2 version offers state-of-the-art numerics for solving coupled sets of nonlinear differential equations. Principal features include application of multi-dimensional Newton-Raphson techniques to accelerate convergence behavior and direct matrix inversion to advance primitive variables from one iterate to the next. Additionally, MELMRK 2.0 provides logical event flags for managing the broad range of code options available for treating such features as (1) coexisting flow regimes, (2) dynamic transitions between flow regimes, and (3) linkages between heatup and relocation code modules. The purpose of this report is to provide a detailed description of the MELMRK 2.0 computer models for melt relocation. Also included are illustrative results for code testing, as well as an integrated calculation for meltdown of a Mark 31a assembly

  8. Pattern formation in flocking models: A hydrodynamic description.

    Science.gov (United States)

    Solon, Alexandre P; Caussin, Jean-Baptiste; Bartolo, Denis; Chaté, Hugues; Tailleur, Julien

    2015-12-01

    We study in detail the hydrodynamic theories describing the transition to collective motion in polar active matter, exemplified by the Vicsek and active Ising models. Using a simple phenomenological theory, we show the existence of an infinity of propagative solutions, describing both phase and microphase separation, that we fully characterize. We also show that the same results hold specifically in the hydrodynamic equations derived in the literature for the active Ising model and for a simplified version of the Vicsek model. We then study numerically the linear stability of these solutions. We show that stable ones constitute only a small fraction of them, which, however, includes all existing types. We further argue that, in practice, a coarsening mechanism leads towards phase-separated solutions. Finally, we construct the phase diagrams of the hydrodynamic equations proposed to qualitatively describe the Vicsek and active Ising models and connect our results to the phenomenology of the corresponding microscopic models.

  9. Advancing reservoir operation description in physically based hydrological models

    Science.gov (United States)

    Anghileri, Daniela; Giudici, Federico; Castelletti, Andrea; Burlando, Paolo

    2016-04-01

    Last decades have seen significant advances in our capacity of characterizing and reproducing hydrological processes within physically based models. Yet, when the human component is considered (e.g. reservoirs, water distribution systems), the associated decisions are generally modeled with very simplistic rules, which might underperform in reproducing the actual operators' behaviour on a daily or sub-daily basis. For example, reservoir operations are usually described by a target-level rule curve, which represents the level that the reservoir should track during normal operating conditions. The associated release decision is determined by the current state of the reservoir relative to the rule curve. This modeling approach can reasonably reproduce the seasonal water volume shift due to reservoir operation. Still, it cannot capture more complex decision making processes in response, e.g., to the fluctuations of energy prices and demands, the temporal unavailability of power plants or varying amount of snow accumulated in the basin. In this work, we link a physically explicit hydrological model with detailed hydropower behavioural models describing the decision making process by the dam operator. In particular, we consider two categories of behavioural models: explicit or rule-based behavioural models, where reservoir operating rules are empirically inferred from observational data, and implicit or optimization based behavioural models, where, following a normative economic approach, the decision maker is represented as a rational agent maximising a utility function. We compare these two alternate modelling approaches on the real-world water system of Lake Como catchment in the Italian Alps. The water system is characterized by the presence of 18 artificial hydropower reservoirs generating almost 13% of the Italian hydropower production. Results show to which extent the hydrological regime in the catchment is affected by different behavioural models and reservoir

  10. Thermodynamically consistent description of criticality in models of correlated electrons

    Czech Academy of Sciences Publication Activity Database

    Janiš, Václav; Kauch, Anna; Pokorný, Vladislav

    2017-01-01

    Roč. 95, č. 4 (2017), s. 1-14, č. článku 045108. ISSN 2469-9950 R&D Projects: GA ČR GA15-14259S Institutional support: RVO:68378271 Keywords : conserving approximations * Anderson model * Hubbard model * parquet equations Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 3.836, year: 2016

  11. Software Test Description (STD) for the Globally Relocatable Navy Tide/Atmospheric Modeling System (PCTides)

    National Research Council Canada - National Science Library

    Posey, Pamela

    2002-01-01

    The purpose of this Software Test Description (STD) is to establish formal test cases to be used by personnel tasked with the installation and verification of the Globally Relocatable Navy Tide/Atmospheric Modeling System (PCTides...

  12. RELAP5 Model Description and Validation for the BR2 Loss-of-Flow Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Licht, J. R. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States); Van den Branden, G. [Argonne National Lab. (ANL), Argonne, IL (United States); Sikik, E. [Argonne National Lab. (ANL), Argonne, IL (United States); Koonen, E. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-07-01

    This paper presents a description of the RELAP5 model, the calibration method used to obtain the minor loss coefficients from the available hydraulic data and the LOFA simulation results compared to the 1963 experimental tests for HEU fuel.

  13. Description of the National Hydrologic Model for use with the Precipitation-Runoff Modeling System (PRMS)

    Science.gov (United States)

    Regan, R. Steven; Markstrom, Steven L.; Hay, Lauren E.; Viger, Roland J.; Norton, Parker A.; Driscoll, Jessica M.; LaFontaine, Jacob H.

    2018-01-08

    This report documents several components of the U.S. Geological Survey National Hydrologic Model of the conterminous United States for use with the Precipitation-Runoff Modeling System (PRMS). It provides descriptions of the (1) National Hydrologic Model, (2) Geospatial Fabric for National Hydrologic Modeling, (3) PRMS hydrologic simulation code, (4) parameters and estimation methods used to compute spatially and temporally distributed default values as required by PRMS, (5) National Hydrologic Model Parameter Database, and (6) model extraction tool named Bandit. The National Hydrologic Model Parameter Database contains values for all PRMS parameters used in the National Hydrologic Model. The methods and national datasets used to estimate all the PRMS parameters are described. Some parameter values are derived from characteristics of topography, land cover, soils, geology, and hydrography using traditional Geographic Information System methods. Other parameters are set to long-established default values and computation of initial values. Additionally, methods (statistical, sensitivity, calibration, and algebraic) were developed to compute parameter values on the basis of a variety of nationally-consistent datasets. Values in the National Hydrologic Model Parameter Database can periodically be updated on the basis of new parameter estimation methods and as additional national datasets become available. A companion ScienceBase resource provides a set of static parameter values as well as images of spatially-distributed parameters associated with PRMS states and fluxes for each Hydrologic Response Unit across the conterminuous United States.

  14. Evaluation factors for verification and validation of low-level waste disposal site models

    International Nuclear Information System (INIS)

    Moran, M.S.; Mezga, L.J.

    1982-01-01

    The purpose of this paper is to identify general evaluation factors to be used to verify and validate LLW disposal site performance models in order to assess their site-specific applicability and to determine their accuracy and sensitivity. It is intended that the information contained in this paper be employed by model users involved with LLW site performance model verification and validation. It should not be construed as providing protocols, but rather as providing a framework for the preparation of specific protocols or procedures. A brief description of each evaluation factor is provided. The factors have been categorized according to recommended use during either the model verification or the model validation process. The general responsibilities of the developer and user are provided. In many cases it is difficult to separate the responsibilities of the developer and user, but the user is ultimately accountable for both verification and validation processes. 4 refs

  15. Biomass Scenario Model Scenario Library: Definitions, Construction, and Description

    Energy Technology Data Exchange (ETDEWEB)

    Inman, D.; Vimmerstedt, L.; Bush, B.; Peterson, S.

    2014-04-01

    Understanding the development of the biofuels industry in the United States is important to policymakers and industry. The Biomass Scenario Model (BSM) is a system dynamics model of the biomass-to-biofuels system that can be used to explore policy effects on biofuels development. Because of the complexity of the model, as well as the wide range of possible future conditions that affect biofuels industry development, we have not developed a single reference case but instead developed a set of specific scenarios that provide various contexts for our analyses. The purpose of this report is to describe the scenarios that comprise the BSM scenario library. At present, we have the following policy-focused scenarios in our library: minimal policies, ethanol-focused policies, equal access to policies, output-focused policies, technological diversity focused, and the point-of-production- focused. This report describes each scenario, its policy settings, and general insights gained through use of the scenarios in analytic studies.

  16. Activated aging dynamics and effective trap model description in the random energy model

    Science.gov (United States)

    Baity-Jesi, M.; Biroli, G.; Cammarota, C.

    2018-01-01

    We study the out-of-equilibrium aging dynamics of the random energy model (REM) ruled by a single spin-flip Metropolis dynamics. We focus on the dynamical evolution taking place on time-scales diverging with the system size. Our aim is to show to what extent the activated dynamics displayed by the REM can be described in terms of an effective trap model. We identify two time regimes: the first one corresponds to the process of escaping from a basin in the energy landscape and to the subsequent exploration of high energy configurations, whereas the second one corresponds to the evolution from a deep basin to the other. By combining numerical simulations with analytical arguments we show why the trap model description does not hold in the former but becomes exact in the second.

  17. Problem with parton-model descriptions of neutrino data

    International Nuclear Information System (INIS)

    Barger, V.; Weiler, T.; Phillips, R.J.N.

    1976-01-01

    The present results from νN and ν-barN scattering experiments appear to place conflicting requirements on conventional quark--parton models. The strong rise with energy of /sup ν-barN and sigma/sup ν-barN/sub T//sigma/ sup νN//sub T/ seems to require new-particle (charm) production from valence quarks in ν-barN interactions, whereas the x dependence of dimuon events and the dsigma/dy anomaly suggest that ν-barN charm production comes from sea quarks. No single model gives a fully satisfactory explanation of all the present data. We draw attention to this problem, illustrate the conflicting requirements of data with particular models, and discuss possible resolutions. The closest overall compromise with the present data is obtained with the six-quark model, using charm-quark masses m/sub c/ = 1.5 GeV, m/sub b/ = 5 GeV, and a higher t-quark mass

  18. A Model for Wetland Hydrology: Description and Validation

    Science.gov (United States)

    R.S. Mansell; S.A. Bloom; Ge Sun

    2000-01-01

    WETLANDS, a multidimensional model describing water flow in variably saturated soil and evapotranspiration, was used to simulate successfully 3-years of local hydrology for a cypress pond located within a relatively flat Coastal Plain pine forest landscape. Assumptions included negligible net regional groundwater flow and radially symmetric local flow impinging on a...

  19. Shell model description of band structure in 48Cr

    International Nuclear Information System (INIS)

    Vargas, Carlos E.; Velazquez, Victor M.

    2007-01-01

    The band structure for normal and abnormal parity bands in 48Cr are described using the m-scheme shell model. In addition to full fp-shell, two particles in the 1d3/2 orbital are allowed in order to describe intruder states. The interaction includes fp-, sd- and mixed matrix elements

  20. General Description of Fission Observables - JEFF Report 24. GEF Model

    International Nuclear Information System (INIS)

    Schmidt, Karl-Heinz; Jurado, Beatriz; Amouroux, Charlotte

    2014-06-01

    The Joint Evaluated Fission and Fusion (JEFF) Project is a collaborative effort among the member countries of the OECD Nuclear Energy Agency (NEA) Data Bank to develop a reference nuclear data library. The JEFF library contains sets of evaluated nuclear data, mainly for fission and fusion applications; it contains a number of different data types, including neutron and proton interaction data, radioactive decay data, fission yield data and thermal scattering law data. The General fission (GEF) model is based on novel theoretical concepts and ideas developed to model low energy nuclear fission. The GEF code calculates fission-fragment yields and associated quantities (e.g. prompt neutron and gamma) for a large range of nuclei and excitation energy. This opens up the possibility of a qualitative step forward to improve further the JEFF fission yields sub-library. This report describes the GEF model which explains the complex appearance of fission observables by universal principles of theoretical models and considerations on the basis of fundamental laws of physics and mathematics. The approach reveals a high degree of regularity and provides a considerable insight into the physics of the fission process. Fission observables can be calculated with a precision that comply with the needs for applications in nuclear technology. The relevance of the approach for examining the consistency of experimental results and for evaluating nuclear data is demonstrated. (authors)

  1. Adaptive filters and internal models: multilevel description of cerebellar function.

    Science.gov (United States)

    Porrill, John; Dean, Paul; Anderson, Sean R

    2013-11-01

    Cerebellar function is increasingly discussed in terms of engineering schemes for motor control and signal processing that involve internal models. To address the relation between the cerebellum and internal models, we adopt the chip metaphor that has been used to represent the combination of a homogeneous cerebellar cortical microcircuit with individual microzones having unique external connections. This metaphor indicates that identifying the function of a particular cerebellar chip requires knowledge of both the general microcircuit algorithm and the chip's individual connections. Here we use a popular candidate algorithm as embodied in the adaptive filter, which learns to decorrelate its inputs from a reference ('teaching', 'error') signal. This algorithm is computationally powerful enough to be used in a very wide variety of engineering applications. However, the crucial issue is whether the external connectivity required by such applications can be implemented biologically. We argue that some applications appear to be in principle biologically implausible: these include the Smith predictor and Kalman filter (for state estimation), and the feedback-error-learning scheme for adaptive inverse control. However, even for plausible schemes, such as forward models for noise cancellation and novelty-detection, and the recurrent architecture for adaptive inverse control, there is unlikely to be a simple mapping between microzone function and internal model structure. This initial analysis suggests that cerebellar involvement in particular behaviours is therefore unlikely to have a neat classification into categories such as 'forward model'. It is more likely that cerebellar microzones learn a task-specific adaptive-filter operation which combines a number of signal-processing roles. Copyright © 2012 Elsevier Ltd. All rights reserved.

  2. Flow modelling in fractured aquifers, development of multi-continua model (direct and inverse problems) and application to the CEA/Cadarache site

    International Nuclear Information System (INIS)

    Cartalade, Alain

    2002-01-01

    This research thesis concerns the modelling of aquifer flows under the CEA/Cadarache site. The author reports the implementation of a numerical simulation tool adapted to large scale flows in fractured media, and its application to the Cadarache nuclear site. After a description of the site geological and hydrogeological characteristics, the author presents the conceptual model on which the modelling is based, presents the inverse model which allows a better definition of parameters, reports the validation of the inverse approach by means of synthetic and semi-synthetic cases. Then, he reports experiments and simulation of the Cadarache site

  3. Translation of a High-Level Temporal Model into Lower Level Models: Impact of Modelling at Different Description Levels

    DEFF Research Database (Denmark)

    Kraft, Peter; Sørensen, Jens Otto

    2001-01-01

    given types of properties, and examine how descriptions on higher levels translate into descriptions on lower levels. Our example looks at temporal properties where the information is concerned with the existence in time. In a high level temporal model with information kept in a three-dimensional space...... the existences in time can be mapped precisely and consistently securing a consistent handling of the temporal properties. We translate the high level temporal model into an entity-relationship model, with the information in a two-dimensional graph, and finally we look at the translations into relational...... and other textual models. We also consider the aptness of models that include procedural mechanisms such as active and object databases...

  4. Cassini Radar EQM Model: Instrument Description and Performance Status

    Science.gov (United States)

    Borgarelli, L.; Faustini, E. Zampolini; Im, E.; Johnson, W. T. K.

    1996-01-01

    The spaeccraft of the Cassini Mission is planned to be launched towards Saturn in October 1997. The mission is designed to study the physical structure and chemical composition of Titan. The results of the tests performed on the Cassini radar engineering qualification model (EQM) are summarized. The approach followed in the verification and evaluation of the performance of the radio frequency subsystem EQM is presented. The results show that the instrument satisfies the relevant mission requirements.

  5. System Advisor Model, SAM 2014.1.14: General Description

    Energy Technology Data Exchange (ETDEWEB)

    Blair, Nate [National Renewable Energy Lab. (NREL), Golden, CO (United States); Dobos, Aron P. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Freeman, Janine [National Renewable Energy Lab. (NREL), Golden, CO (United States); Neises, Ty [National Renewable Energy Lab. (NREL), Golden, CO (United States); Wagner, Michael [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ferguson, Tom [Global Resources, Northbrook, IL (United States); Gilman, Paul [National Renewable Energy Lab. (NREL), Golden, CO (United States); Janzou, Steven [Janzou Consulting, Idaho Springs, CO (United States)

    2014-02-01

    This document describes the capabilities of the U.S. Department of Energy and National Renewable Energy Laboratory's System Advisor Model (SAM), Version 2013.9.20, released on September 9, 2013. SAM is a computer model that calculates performance and financial metrics of renewable energy systems. Project developers, policy makers, equipment manufacturers, and researchers use graphs and tables of SAM results in the process of evaluating financial, technology, and incentive options for renewable energy projects. SAM simulates the performance of photovoltaic, concentrating solar power, solar water heating, wind, geothermal, biomass, and conventional power systems. The financial model can represent financial structures for projects that either buy and sell electricity at retail rates (residential and commercial) or sell electricity at a price determined in a power purchase agreement (utility). SAM's advanced simulation options facilitate parametric and sensitivity analyses, and statistical analysis capabilities are available for Monte Carlo simulation and weather variability (P50/P90) studies. SAM can also read input variables from Microsoft Excel worksheets. For software developers, the SAM software development kit (SDK) makes it possible to use SAM simulation modules in their applications written in C/C++, C#, Java, Python, and MATLAB. NREL provides both SAM and the SDK as free downloads at http://sam.nrel.gov. Technical support and more information about the software are available on the website.

  6. Description of waste pretreatment and interfacing systems dynamic simulation model

    International Nuclear Information System (INIS)

    Garbrick, D.J.; Zimmerman, B.D.

    1995-05-01

    The Waste Pretreatment and Interfacing Systems Dynamic Simulation Model was created to investigate the required pretreatment facility processing rates for both high level and low level waste so that the vitrification of tank waste can be completed according to the milestones defined in the Tri-Party Agreement (TPA). In order to achieve this objective, the processes upstream and downstream of the pretreatment facilities must also be included. The simulation model starts with retrieval of tank waste and ends with vitrification for both low level and high level wastes. This report describes the results of three simulation cases: one based on suggested average facility processing rates, one with facility rates determined so that approximately 6 new DSTs are required, and one with facility rates determined so that approximately no new DSTs are required. It appears, based on the simulation results, that reasonable facility processing rates can be selected so that no new DSTs are required by the TWRS program. However, this conclusion must be viewed with respect to the modeling assumptions, described in detail in the report. Also included in the report, in an appendix, are results of two sensitivity cases: one with glass plant water recycle steams recycled versus not recycled, and one employing the TPA SST retrieval schedule versus a more uniform SST retrieval schedule. Both recycling and retrieval schedule appear to have a significant impact on overall tank usage

  7. The electricity portfolio simulation model (EPSim) technical description.

    Energy Technology Data Exchange (ETDEWEB)

    Drennen, Thomas E.; Klotz, Richard (Hobart and William Smith Colleges, Geneva, NY)

    2005-09-01

    Stakeholders often have competing interests when selecting or planning new power plants. The purpose of developing this preliminary Electricity Portfolio Simulation Model (EPSim) is to provide a first cut, dynamic methodology and approach to this problem, that can subsequently be refined and validated, that may help energy planners, policy makers, and energy students better understand the tradeoffs associated with competing electricity portfolios. EPSim allows the user to explore competing electricity portfolios annually from 2002 to 2025 in terms of five different criteria: cost, environmental impacts, energy dependence, health and safety, and sustainability. Four additional criteria (infrastructure vulnerability, service limitations, policy needs and science and technology needs) may be added in future versions of the model. Using an analytic hierarchy process (AHP) approach, users or groups of users apply weights to each of the criteria. The default energy assumptions of the model mimic Department of Energy's (DOE) electricity portfolio to 2025 (EIA, 2005). At any time, the user can compare alternative portfolios to this reference case portfolio.

  8. Quark-diquark model description for double charm baryons

    International Nuclear Information System (INIS)

    Majethiya, A.; Patel, B.; Vinodkumar, P. C.

    2010-01-01

    We report here the mass spectrum and magnetic moments of ccq(q (implied by) u, d, s) systems in the potential model framework by assuming the inter-quark potential as the colour coulomb plus power form with power index ν varying between 0.1 to 2.0. Here the two charm quarks are considered for the diquark states. The conventional one gluon exchange interaction has been employed to get the hyperfine and the fine structure between different states. We have predicted many low-lying states whose experimental verification can exclusively support the quark-diquark structure of the baryons. (authors)

  9. Stress description model by non destructive magnetic methods

    International Nuclear Information System (INIS)

    Flambard, C.; Grossiord, J.L.; Tourrenc, P.

    1983-01-01

    Since a few years, CETIM investigates analysis possibilities of materials, by developing a method founded on observation of ferromagnetic noise. By experiments, correlations have become obvious between state of the material and recorded signal. These correlations open to industrial applications to measure stresses and strains in elastic and plastic ranges. This article starts with a brief historical account and theoretical backgrounds of the method. The experimental frame of this research is described, and the main results are analyzed. Theoretically, a model was built up, and we present it. It seems in agreement with some experimental observations. The main results concerning stress application, thermal and surface treatments (decarbonizing) are presented [fr

  10. A Descriptive Evaluation of Automated Software Cost-Estimation Models,

    Science.gov (United States)

    1986-10-01

    Version 1.03D) * PCOC (Version 7.01) - PRICE S • SLIM (Version 1.1) • SoftCost (Version 5. 1) * SPQR /20 (Version 1. 1) - WICOMO (Version 1.3) These...produce detailed GANTT and PERT charts. SPQR /20 is based on a cost model developed at ITT. In addition to cost, schedule, and staffing estimates, it...cases and test runs required, and the effectiveness of pre-test and test activities. SPQR /20 also predicts enhancement and maintenance activities. C

  11. Parallel community climate model: Description and user`s guide

    Energy Technology Data Exchange (ETDEWEB)

    Drake, J.B.; Flanery, R.E.; Semeraro, B.D.; Worley, P.H. [and others

    1996-07-15

    This report gives an overview of a parallel version of the NCAR Community Climate Model, CCM2, implemented for MIMD massively parallel computers using a message-passing programming paradigm. The parallel implementation was developed on an Intel iPSC/860 with 128 processors and on the Intel Delta with 512 processors, and the initial target platform for the production version of the code is the Intel Paragon with 2048 processors. Because the implementation uses a standard, portable message-passing libraries, the code has been easily ported to other multiprocessors supporting a message-passing programming paradigm. The parallelization strategy used is to decompose the problem domain into geographical patches and assign each processor the computation associated with a distinct subset of the patches. With this decomposition, the physics calculations involve only grid points and data local to a processor and are performed in parallel. Using parallel algorithms developed for the semi-Lagrangian transport, the fast Fourier transform and the Legendre transform, both physics and dynamics are computed in parallel with minimal data movement and modest change to the original CCM2 source code. Sequential or parallel history tapes are written and input files (in history tape format) are read sequentially by the parallel code to promote compatibility with production use of the model on other computer systems. A validation exercise has been performed with the parallel code and is detailed along with some performance numbers on the Intel Paragon and the IBM SP2. A discussion of reproducibility of results is included. A user`s guide for the PCCM2 version 2.1 on the various parallel machines completes the report. Procedures for compilation, setup and execution are given. A discussion of code internals is included for those who may wish to modify and use the program in their own research.

  12. Description of a practice model for pharmacist medication review in a general practice setting

    DEFF Research Database (Denmark)

    Brandt, Mette; Hallas, Jesper; Hansen, Trine Graabæk

    2014-01-01

    BACKGROUND: Practical descriptions of procedures used for pharmacists' medication reviews are sparse. OBJECTIVE: To describe a model for medication review by pharmacists tailored to a general practice setting. METHODS: A stepwise model is described. The model is based on data from the medical chart...... no indication (n=47, 23%). Most interventions were aimed at cardiovascular drugs. CONCLUSION: We have provided a detailed description of a practical approach to pharmacists' medication review in a GP setting. The model was tested and found to be usable, and to deliver a medication review with high acceptance...

  13. Benchmark problems for repository siting models

    International Nuclear Information System (INIS)

    Ross, B.; Mercer, J.W.; Thomas, S.D.; Lester, B.H.

    1982-12-01

    This report describes benchmark problems to test computer codes used in siting nuclear waste repositories. Analytical solutions, field problems, and hypothetical problems are included. Problems are included for the following types of codes: ground-water flow in saturated porous media, heat transport in saturated media, ground-water flow in saturated fractured media, heat and solute transport in saturated porous media, solute transport in saturated porous media, solute transport in saturated fractured media, and solute transport in unsaturated porous media

  14. Modeling of hydrologic perturbations during reverse circulation drilling: 1, System and model description

    International Nuclear Information System (INIS)

    Sagar, B.; Connelly, M.P.; Long, P.E.

    1988-05-01

    The Hanford site located in southeastern Washington state was under consideration for the location of a high-level nuclear waste repository. As a part of site investigation, a borehole of depth > 3000 ft was drilled using reverse circulation drilling technique with water as the drilling fluid. After completion of drilling, seven piezometers were to be installed in the borehole with their lower ends at different depths to measure equilibrated hydraulic heads and aquifer response during future pumping tests. The hydrologic perturbations caused during the drilling, clean up, and piezometer installation process were of primary concern. A numerical model was used to predict these perturbations and determine efficiency of borehole cleanup. It was found that the boundary condition at the borehole was the most difficult to model. 9 refs., 5 figs

  15. Description of group-theoretical model of developed turbulence

    International Nuclear Information System (INIS)

    Saveliev, V L; Gorokhovski, M A

    2008-01-01

    We propose to associate the phenomenon of stationary turbulence with the special self-similar solutions of the Euler equations. These solutions represent the linear superposition of eigenfields of spatial symmetry subgroup generators and imply their dependence on time through the parameter of the symmetry transformation only. From this model, it follows that for developed turbulent process, changing the scale of averaging (filtering) of the velocity field is equivalent to composition of scaling, translation and rotation transformations. We call this property a renormalization-group invariance of filtered turbulent fields. The renormalization group invariance provides an opportunity to transform the averaged Navier-Stokes equation over a small scale (inner threshold of the turbulence) to larger scales by simple scaling. From the methodological point of view, it is significant to note that the turbulent viscosity term appeared not as a result of averaging of the nonlinear term in the Navier-Stokes equation, but from the molecular viscosity term with the help of renormalization group transformation.

  16. Teacher Preferences for Alternative School Site Administrative Models

    Science.gov (United States)

    Hewitt, Paul M.; Denny, George S.; Pijanowski, John C.

    2012-01-01

    Public school teachers with high leadership potential who stated that they had no interest in being school principals were surveyed on their attitudes about six alternative school site administrative organizational models. Of the 391 teachers surveyed, 53% identified the Co-Principal model as the preferred school site administrative structure. In…

  17. Using Dirichlet Processes for Modeling Heterogeneous Treatment Effects across Sites

    Science.gov (United States)

    Miratrix, Luke; Feller, Avi; Pillai, Natesh; Pati, Debdeep

    2016-01-01

    Modeling the distribution of site level effects is an important problem, but it is also an incredibly difficult one. Current methods rely on distributional assumptions in multilevel models for estimation. There it is hoped that the partial pooling of site level estimates with overall estimates, designed to take into account individual variation as…

  18. Water-rock interaction modelling and uncertainties of mixing modelling. SDM-Site Laxemar

    International Nuclear Information System (INIS)

    Gimeno, Maria J.; Auque, Luis F.; Gomez, Javier B.; Acero, Patricia

    2009-01-01

    The overall objectives of hydrogeochemical description for Laxemar are to establish a detailed understanding of the hydrogeochemical conditions at the site and to develop models that fulfil the needs identified by the safety assessment groups during the site investigation phase. Issues of concern to safety assessment are radionuclide transport and technical barrier behaviour, both of which are dependent on the chemistry of groundwater and pore water and their evolution with time. The work has involved the development of descriptive and mathematical models for groundwaters in relation to rock domains, fracture domains and deformation zones. Past climate changes are the major driving force for hydrogeochemical changes and therefore of fundamental importance for understanding the palaeohydrogeological, palaeohydrogeochemical and present evolution of groundwater in the crystalline bedrock of the Fennoscandian Shield. Understanding current undisturbed hydrochemical conditions at the proposed repository site is important when predicting future changes in groundwater chemistry. The causes of copper corrosion and/or bentonite degradation are of particular interest as they may jeopardise the long-term integrity of the planned SKB repository system. Thus, the following variables are considered for the hydrogeochemical site descriptive modelling: pH, Eh, sulphur species, iron, manganese, carbonate, phosphate, nitrogen species, total dissolved solids (TDS), isotopes, colloids, fulvic and humic acids and microorganisms. In addition, dissolved gases (e.g. carbon dioxide, methane and hydrogen) are of interest because of their likely participation in microbial reactions. In this series of reports, the final hydrogeochemical evaluation work of the site investigation at the Laxemar site, is presented. The work was conducted by SKB's hydrogeochemical project group, ChemNet, which consists of independent consultants and Univ. researchers with expertise in geochemistry, hydrochemistry

  19. Water-rock interaction modelling and uncertainties of mixing modelling. SDM-Site Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Gimeno, Maria J.; Auque, Luis F.; Gomez, Javier B.; Acero, Patricia (Univ. of Zaragoza, Zaragoza (Spain))

    2009-01-15

    The overall objectives of hydrogeochemical description for Laxemar are to establish a detailed understanding of the hydrogeochemical conditions at the site and to develop models that fulfil the needs identified by the safety assessment groups during the site investigation phase. Issues of concern to safety assessment are radionuclide transport and technical barrier behaviour, both of which are dependent on the chemistry of groundwater and pore water and their evolution with time. The work has involved the development of descriptive and mathematical models for groundwaters in relation to rock domains, fracture domains and deformation zones. Past climate changes are the major driving force for hydrogeochemical changes and therefore of fundamental importance for understanding the palaeohydrogeological, palaeohydrogeochemical and present evolution of groundwater in the crystalline bedrock of the Fennoscandian Shield. Understanding current undisturbed hydrochemical conditions at the proposed repository site is important when predicting future changes in groundwater chemistry. The causes of copper corrosion and/or bentonite degradation are of particular interest as they may jeopardise the long-term integrity of the planned SKB repository system. Thus, the following variables are considered for the hydrogeochemical site descriptive modelling: pH, Eh, sulphur species, iron, manganese, carbonate, phosphate, nitrogen species, total dissolved solids (TDS), isotopes, colloids, fulvic and humic acids and microorganisms. In addition, dissolved gases (e.g. carbon dioxide, methane and hydrogen) are of interest because of their likely participation in microbial reactions. In this series of reports, the final hydrogeochemical evaluation work of the site investigation at the Laxemar site, is presented. The work was conducted by SKB's hydrogeochemical project group, ChemNet, which consists of independent consultants and Univ. researchers with expertise in geochemistry

  20. The Chemistry of Atmosphere-Forest Exchange (CAFE Model – Part 1: Model description and characterization

    Directory of Open Access Journals (Sweden)

    G. M. Wolfe

    2011-01-01

    Full Text Available We present the Chemistry of Atmosphere-Forest Exchange (CAFE model, a vertically-resolved 1-D chemical transport model designed to probe the details of near-surface reactive gas exchange. CAFE integrates all key processes, including turbulent diffusion, emission, deposition and chemistry, throughout the forest canopy and mixed layer. CAFE utilizes the Master Chemical Mechanism (MCM and is the first model of its kind to incorporate a suite of reactions for the oxidation of monoterpenes and sesquiterpenes, providing a more comprehensive description of the oxidative chemistry occurring within and above the forest. We use CAFE to simulate a young Ponderosa pine forest in the Sierra Nevada, CA. Utilizing meteorological constraints from the BEARPEX-2007 field campaign, we assess the sensitivity of modeled fluxes to parameterizations of diffusion, laminar sublayer resistance and radiation extinction. To characterize the general chemical environment of this forest, we also present modeled mixing ratio profiles of biogenic hydrocarbons, hydrogen oxides and reactive nitrogen. The vertical profiles of these species demonstrate a range of structures and gradients that reflect the interplay of physical and chemical processes within the forest canopy, which can influence net exchange.

  1. Physical models for the description of an electrodynamically accelerated plasma sheath

    International Nuclear Information System (INIS)

    Zambreanu, V.

    1977-01-01

    An analysis of the models proposed for the description of the plasma sheath dynamics in a coaxial system (of the same type as that operating at the Bucharest Institute of Physics) is presented. A particular attention is paid to the physical structure of the accelerated plasma. It has been shown that a self-consistent model could be derived from a phenomenological description of the sheath structure. The physical models presented so far in the literature have been classified into three groups: the hydrodynamic models, the plasma sheet models and the shock wave models. Each of these models is briefly described. The simplifying assumptions used in the construction of these models have been pointed out. The final conclusion has been that, under these assumptions, none of these models taken separately could completely and correctly describe the dynamical state of the plasma sheath. (author)

  2. Mathematical description of drug-target interactions: application to biologics that bind to targets with two binding sites.

    Science.gov (United States)

    Gibiansky, Leonid; Gibiansky, Ekaterina

    2018-02-01

    The emerging discipline of mathematical pharmacology occupies the space between advanced pharmacometrics and systems biology. A characteristic feature of the approach is application of advance mathematical methods to study the behavior of biological systems as described by mathematical (most often differential) equations. One of the early application of mathematical pharmacology (that was not called this name at the time) was formulation and investigation of the target-mediated drug disposition (TMDD) model and its approximations. The model was shown to be remarkably successful, not only in describing the observed data for drug-target interactions, but also in advancing the qualitative and quantitative understanding of those interactions and their role in pharmacokinetic and pharmacodynamic properties of biologics. The TMDD model in its original formulation describes the interaction of the drug that has one binding site with the target that also has only one binding site. Following the framework developed earlier for drugs with one-to-one binding, this work aims to describe a rigorous approach for working with similar systems and to apply it to drugs that bind to targets with two binding sites. The quasi-steady-state, quasi-equilibrium, irreversible binding, and Michaelis-Menten approximations of the model are also derived. These equations can be used, in particular, to predict concentrations of the partially bound target (RC). This could be clinically important if RC remains active and has slow internalization rate. In this case, introduction of the drug aimed to suppress target activity may lead to the opposite effect due to RC accumulation.

  3. Vehicle Modeling for use in the CAFE model: Process description and modeling assumptions

    Energy Technology Data Exchange (ETDEWEB)

    Moawad, Ayman [Argonne National Lab. (ANL), Argonne, IL (United States); Kim, Namdoo [Argonne National Lab. (ANL), Argonne, IL (United States); Rousseau, Aymeric [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-06-01

    The objective of this project is to develop and demonstrate a process that, at a minimum, provides more robust information that can be used to calibrate inputs applicable under the CAFE model’s existing structure. The project will be more fully successful if a process can be developed that minimizes the need for decision trees and replaces the synergy factors by inputs provided directly from a vehicle simulation tool. The report provides a description of the process that was developed by Argonne National Laboratory and implemented in Autonomie.

  4. Power system models - A description of power markets and outline of market modelling in Wilmar

    DEFF Research Database (Denmark)

    Meibom, Peter; Morthorst, Poul Erik; Nielsen, Lars Henrik

    2004-01-01

    The aim of the Wilmar project is to investigate technical and economical problems related to large-scale deployment of renewable sources and to develop a modelling tool that can handle system simulations for a larger geographical region with anInternational power exchange. Wilmar is an abbreviati...... description of the power market models usedin Wilmar is given in the second part, though the mathematical presentations of the models are left out of this report and will be treated in a later publication from the project.......The aim of the Wilmar project is to investigate technical and economical problems related to large-scale deployment of renewable sources and to develop a modelling tool that can handle system simulations for a larger geographical region with anInternational power exchange. Wilmar is an abbreviation...... of “Wind Power Integration in Liberalised Electricity Markets”. The project was started in 2002 and is funded by the EU’s 5th Research programme on energy and environment. Risø National Laboratory isco-ordinator of the project and partners include SINTEF, Kungliga Tekniska Högskola, University of Stuttgart...

  5. Statistical modeling in phenomenological description of electromagnetic cascade processes produced by high-energy gamma quanta

    International Nuclear Information System (INIS)

    Slowinski, B.

    1987-01-01

    A description of a simple phenomenological model of electromagnetic cascade process (ECP) initiated by high-energy gamma quanta in heavy absorbents is given. Within this model spatial structure and fluctuations of ionization losses of shower electrons and positrons are described. Concrete formulae have been obtained as a result of statistical analysis of experimental data from the xenon bubble chamber of ITEP (Moscow)

  6. A note on the translation of conceptual data models into description logics: disjointness and covering assumptions

    CSIR Research Space (South Africa)

    Casini, G

    2012-10-01

    Full Text Available possibilities for conceptual data modeling. It also raises the question of how existing conceptual models using ER, UML or ORM could be translated into Description Logics (DLs), a family of logics that have proved to be particularly appropriate for formalizing...

  7. Diverging strains near threshold: Breakdown of the elastic description of a charge density wave model

    International Nuclear Information System (INIS)

    Mungan, M.; Coppersmith, S.; Vinokur, V.M.

    1999-01-01

    We analyze the strains near threshold in 1-d charge density wave models at zero temperature and strong pinning. We show that in these models local strains diverge near the depinning threshold and characterize the scaling behavior of the phenomenon. This helps quantify when the underlying elastic description breaks down and plastic effects have to be included

  8. Impact of uncertainty description on assimilating hydraulic head in the MIKE SHE distributed hydrological model

    DEFF Research Database (Denmark)

    Zhang, Donghua; Madsen, Henrik; Ridler, Marc E.

    2015-01-01

    The ensemble Kalman filter (EnKF) is a popular data assimilation (DA) technique that has been extensively used in environmental sciences for combining complementary information from model predictions and observations. One of the major challenges in EnKF applications is the description of model un...... with respect to performance and sensitivity. Results show that inappropriate definition of model uncertainty can greatly degrade the assimilation performance, and an appropriate combination of different model uncertainty sources is advised....

  9. A Bayesian belief network approach for assessing uncertainty in conceptual site models at contaminated sites

    Science.gov (United States)

    Thomsen, Nanna I.; Binning, Philip J.; McKnight, Ursula S.; Tuxen, Nina; Bjerg, Poul L.; Troldborg, Mads

    2016-05-01

    A key component in risk assessment of contaminated sites is in the formulation of a conceptual site model (CSM). A CSM is a simplified representation of reality and forms the basis for the mathematical modeling of contaminant fate and transport at the site. The CSM should therefore identify the most important site-specific features and processes that may affect the contaminant transport behavior at the site. However, the development of a CSM will always be associated with uncertainties due to limited data and lack of understanding of the site conditions. CSM uncertainty is often found to be a major source of model error and it should therefore be accounted for when evaluating uncertainties in risk assessments. We present a Bayesian belief network (BBN) approach for constructing CSMs and assessing their uncertainty at contaminated sites. BBNs are graphical probabilistic models that are effective for integrating quantitative and qualitative information, and thus can strengthen decisions when empirical data are lacking. The proposed BBN approach facilitates a systematic construction of multiple CSMs, and then determines the belief in each CSM using a variety of data types and/or expert opinion at different knowledge levels. The developed BBNs combine data from desktop studies and initial site investigations with expert opinion to assess which of the CSMs are more likely to reflect the actual site conditions. The method is demonstrated on a Danish field site, contaminated with chlorinated ethenes. Four different CSMs are developed by combining two contaminant source zone interpretations (presence or absence of a separate phase contamination) and two geological interpretations (fractured or unfractured clay till). The beliefs in each of the CSMs are assessed sequentially based on data from three investigation stages (a screening investigation, a more detailed investigation, and an expert consultation) to demonstrate that the belief can be updated as more information

  10. Modeling Site Heterogeneity with Posterior Mean Site Frequency Profiles Accelerates Accurate Phylogenomic Estimation.

    Science.gov (United States)

    Wang, Huai-Chun; Minh, Bui Quang; Susko, Edward; Roger, Andrew J

    2018-03-01

    Proteins have distinct structural and functional constraints at different sites that lead to site-specific preferences for particular amino acid residues as the sequences evolve. Heterogeneity in the amino acid substitution process between sites is not modeled by commonly used empirical amino acid exchange matrices. Such model misspecification can lead to artefacts in phylogenetic estimation such as long-branch attraction. Although sophisticated site-heterogeneous mixture models have been developed to address this problem in both Bayesian and maximum likelihood (ML) frameworks, their formidable computational time and memory usage severely limits their use in large phylogenomic analyses. Here we propose a posterior mean site frequency (PMSF) method as a rapid and efficient approximation to full empirical profile mixture models for ML analysis. The PMSF approach assigns a conditional mean amino acid frequency profile to each site calculated based on a mixture model fitted to the data using a preliminary guide tree. These PMSF profiles can then be used for in-depth tree-searching in place of the full mixture model. Compared with widely used empirical mixture models with $k$ classes, our implementation of PMSF in IQ-TREE (http://www.iqtree.org) speeds up the computation by approximately $k$/1.5-fold and requires a small fraction of the RAM. Furthermore, this speedup allows, for the first time, full nonparametric bootstrap analyses to be conducted under complex site-heterogeneous models on large concatenated data matrices. Our simulations and empirical data analyses demonstrate that PMSF can effectively ameliorate long-branch attraction artefacts. In some empirical and simulation settings PMSF provided more accurate estimates of phylogenies than the mixture models from which they derive.

  11. Alternative DFN model based on initial site investigations at Simpevarp

    Energy Technology Data Exchange (ETDEWEB)

    Darcel, C. [Itasca Consultants, Ecully (France); Davy, S.A.P.; Bour, O.; Dreuzy, J.R. de [Geosciences, Rennes (France)

    2004-12-01

    In this report, we provide a first-order analysis of the fracture network at the Simpevarp site. The first order model is the fracture distribution function, noted, fdf, which provides the number of fractures having a given orientation and length, and belonging to a given volume of observation. The first-order distribution model does not describe higher-order correlation between fracture parameters, such as a possible dependency of fracture length distribution with orientations. We also check that most of the information is contained in this 1st-order distribution model, and that dividing the fracture networks into different sets do not bring a better statistical description. The fracture distribution function contains 3 main distributions: the probability distribution of fracture orientations, the dependency on the size of the sampling domain that may exhibit non-trivial scaling in case of fractal correlations, and the fracture-length density distribution, which appears to be well fitted by a power law. The main scaling parameters are the fractal dimension and the power-law exponent of the fracture length distribution. The former was found to be about equal to the embedding dimension, meaning that fractal correlations are weak and can be neglected in the DFN model. The latter depends on geology, that is either lithology or grain size, with values that ranges from 3.2 for granite-like outcrops to 4 for diorite or monzodiorite outcrops, as well as for the large-scale lineament maps. When analyzing the consistency of the different datasets (boreholes, outcrops, lineament maps), we found that two different DFNs can be described: the first one is derived from the fdf of the outcrop with fine-grained size lithology, and is valid across all scales investigated in this study, from the highly-fractured cores to large-scale maps; the second one is derived from the fdf of the outcrops with coarse-grained size lithology, and is found consistent with cores that present the

  12. Overview of the Manitou Experimental Forest Observatory: site description and selected science results from 2008 to 2013

    Science.gov (United States)

    Ortega, J.; Turnipseed, A.; Guenther, A. B.; Karl, T. G.; Day, D. A.; Gochis, D.; Huffman, J. A.; Prenni, A. J.; Levin, E. J. T.; Kreidenweis, S. M.; DeMott, P. J.; Tobo, Y.; Patton, E. G.; Hodzic, A.; Cui, Y. Y.; Harley, P. C.; Hornbrook, R. S.; Apel, E. C.; Monson, R. K.; Eller, A. S. D.; Greenberg, J. P.; Barth, M. C.; Campuzano-Jost, P.; Palm, B. B.; Jimenez, J. L.; Aiken, A. C.; Dubey, M. K.; Geron, C.; Offenberg, J.; Ryan, M. G.; Fornwalt, P. J.; Pryor, S. C.; Keutsch, F. N.; DiGangi, J. P.; Chan, A. W. H.; Goldstein, A. H.; Wolfe, G. M.; Kim, S.; Kaser, L.; Schnitzhofer, R.; Hansel, A.; Cantrell, C. A.; Mauldin, R. L.; Smith, J. N.

    2014-06-01

    The Bio-hydro-atmosphere interactions of Energy, Aerosols, Carbon, H2O, Organics & Nitrogen (BEACHON) project seeks to understand the feedbacks and inter-relationships between hydrology, biogenic emissions, carbon assimilation, aerosol properties, clouds and associated feedbacks within water-limited ecosystems. The Manitou Experimental Forest Observatory (MEFO) was established in 2008 by the National Center for Atmospheric Research to address many of the BEACHON research objectives, and it now provides a fixed field site with significant infrastructure. MEFO is a mountainous, semi-arid ponderosa pine-dominated forest site that is normally dominated by clean continental air but is periodically influenced by anthropogenic sources from Colorado Front Range cities. This article summarizes the past and ongoing research activities at the site, and highlights some of the significant findings that have resulted from these measurements. These activities include - soil property measurements; - hydrological studies; - measurements of high-frequency turbulence parameters; - eddy covariance flux measurements of water, energy, aerosols and carbon dioxide through the canopy; - determination of biogenic and anthropogenic volatile organic compound emissions and their influence on regional atmospheric chemistry; - aerosol number and mass distributions; - chemical speciation of aerosol particles; - characterization of ice and cloud condensation nuclei; - trace gas measurements; and - model simulations using coupled chemistry and meteorology. In addition to various long-term continuous measurements, three focused measurement campaigns with state-of-the-art instrumentation have taken place since the site was established, and two of these studies are the subjects of this special issue: BEACHON-ROCS (Rocky Mountain Organic Carbon Study, 2010) and BEACHON-RoMBAS (Rocky Mountain Biogenic Aerosol Study, 2011).

  13. Overview of the Manitou Experimental Forest Observatory: site description and selected science results from 2008-2013

    Science.gov (United States)

    Ortega, J.; Turnipseed, A.; Guenther, A. B.; Karl, T. G.; Day, D. A.; Gochis, D.; Huffman, J. A.; Prenni, A. J.; Levin, E. J. T.; Kreidenweis, S. M.; DeMott, P. J.; Tobo, Y.; Patton, E. G.; Hodzic, A.; Cui, Y.; Harley, P. C.; Hornbrook, R. H.; Apel, E. C.; Monson, R. K.; Eller, A. S. D.; Greenberg, J. P.; Barth, M.; Campuzano-Jost, P.; Palm, B. B.; Jimenez, J. L.; Aiken, A. C.; Dubey, M. K.; Geron, C.; Offenberg, J.; Ryan, M. G.; Fornwalt, P. J.; Pryor, S. C.; Keutsch, F. N.; DiGangi, J. P.; Chan, A. W. H.; Goldstein, A. H.; Wolfe, G. M.; Kim, S.; Kaser, L.; Schnitzhofer, R.; Hansel, A.; Cantrell, C. A.; Mauldin, R. L., III; Smith, J. N.

    2014-01-01

    The Bio-hydro-atmosphere interactions of Energy, Aerosols, Carbon, H2O, Organics & Nitrogen (BEACHON) project seeks to understand the feedbacks and inter-relationships between hydrology, biogenic emissions, carbon assimilation, aerosol properties, clouds and associated feedbacks within water-limited ecosystems. The Manitou Experimental Forest Observatory (MEFO) was established in 2008 by the National Center for Atmospheric Research to address many of the BEACHON research objectives, and it now provides a fixed field site with significant infrastructure. MEFO is a mountainous, semi-arid ponderosa pine-dominated forest site that is normally dominated by clean continental air, but is periodically influenced by anthropogenic sources from Colorado Front Range cities. This article summarizes the past and ongoing research activities at the site, and highlights some of the significant findings that have resulted from these measurements. These activities include: - soil property measurements, - hydrological studies, - measurements of high-frequency turbulence parameters, - eddy covariance flux measurements of water, energy, aerosols and carbon dioxide through the canopy, - biogenic and anthropogenic volatile organic compound emissions and their influence on regional atmospheric chemistry, - aerosol number and mass distributions, - chemical speciation of aerosol particles, - characterization of ice and cloud condensation nuclei, - trace gas measurements, and - model simulations using coupled chemistry and meteorology. In addition to various long-term continuous measurement, three focused measurement campaigns with state-of-the-art instrumentation have taken place since the site was established, and two of these are the subjects of this special issue: BEACHON-ROCS (Rocky Mountain Organic Carbon Study, 2010) and BEACHON-RoMBAS (Rocky Mountain Biogenic Aerosol Study, 2011).

  14. Biotrans functional and technical description. Report of VIEWLS WP5, modelling studies

    International Nuclear Information System (INIS)

    Van Tilburg, X.; Egging, R.; Londo, H.M.

    2006-01-01

    The overall objectives of this project are to provide structured and clear data on the availability and performance of biofuels and to identify the possibilities and strategies towards large scale sustainable production, use and trading of biofuels for the transport sector in Europe, including Central and Eastern European Countries (CEEC). The report supplements the two other reports in the work package: 'Biofuel and Bio-energy implementation scenarios - final report of VIEWLS WP5' (2005) and 'VIEWLS modelling and analysis, technical data for biofuel production chains' (2005). This document contains a functional and technical description of the BioTrans model, accompanied by a description of the system. Section 2 contains a conceptual and functional description of the biofuel model. Section 3 describes the optimisation method in technical terms, discussing aspects like the target function and constraints used. Finally, section 4 discusses the input and output requirements for the BioTrans system

  15. A description of LUSTRA's common field sites[Forestry land use and greenhouse gas emissions

    Energy Technology Data Exchange (ETDEWEB)

    Berggren, Dan [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden). Dept. of Soil Sciences; Bergkvist, Bo [Lund Univ. (Sweden). Dept. of Ecology; Johansson, Maj-Britt; Melkerud, Per-Arne; Nilsson, Aake; Olsson, Mats [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden). Dept. of Forest Soils; Langvall, Ola [Swedish Univ. of Agricultural Sciences, Lammhult (Sweden). Asa Experimental Forest; Majdi, Hooshang [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden). Dept. of Ecology and Environmental Research; Weslien, Per [Goeteborg Univ. (Sweden). Botanical Inst.

    2004-07-01

    participate on the global arena, and thus LUSTRA has gradually put more focus on the Kyoto process. LUSTRA was evaluated during spring 2002 and the general overall statement was that 'The ambitious goals of the LUSTRA program are very good and seem to be well understood by the participating researchers. However, for a second phase a focus on synthesis and synergy is recommended'. In LUSTRA we are performing integrated research on C fluxes at three common field sites (CFS) situated in a south-north transect in Sweden: Asa, Knottaasen and Flakaliden. Measurements started summer 2000. The intention was to establish a climate gradient through Sweden but keep other environmental parameters rather similar. Also within each site the ambition was to get a hydrological gradient going from dry, over mesic to moist conditions, i.e. from deep lying ground water level to shallow groundwater. According to the advises by the reviewers of LUSTRA phase 1, more focus will be on syntheses during LUSTRA phase 2 (2003-2006). However, measurements at the CFS will be continued during 2003 and 2004. The objectives of this paper are (i) to give a general description of the sites, (ii) to describe the abiotic measurements made at the different sites, including the data base, (iii) to describe the methods used to obtain background information about soils and vegetation (C pools and fluxes) and (iv) to present the background information about soils and vegetation.

  16. Maximum-likelihood model averaging to profile clustering of site types across discrete linear sequences.

    Directory of Open Access Journals (Sweden)

    Zhang Zhang

    2009-06-01

    Full Text Available A major analytical challenge in computational biology is the detection and description of clusters of specified site types, such as polymorphic or substituted sites within DNA or protein sequences. Progress has been stymied by a lack of suitable methods to detect clusters and to estimate the extent of clustering in discrete linear sequences, particularly when there is no a priori specification of cluster size or cluster count. Here we derive and demonstrate a maximum likelihood method of hierarchical clustering. Our method incorporates a tripartite divide-and-conquer strategy that models sequence heterogeneity, delineates clusters, and yields a profile of the level of clustering associated with each site. The clustering model may be evaluated via model selection using the Akaike Information Criterion, the corrected Akaike Information Criterion, and the Bayesian Information Criterion. Furthermore, model averaging using weighted model likelihoods may be applied to incorporate model uncertainty into the profile of heterogeneity across sites. We evaluated our method by examining its performance on a number of simulated datasets as well as on empirical polymorphism data from diverse natural alleles of the Drosophila alcohol dehydrogenase gene. Our method yielded greater power for the detection of clustered sites across a breadth of parameter ranges, and achieved better accuracy and precision of estimation of clusters, than did the existing empirical cumulative distribution function statistics.

  17. Water-rock interaction modelling and uncertainties of mixing modelling. SDM-Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Gimeno, Maria J.; Auque, Luis F.; Gomez, Javier B.; Acero, Patricia (Univ. of Zaragoza, Zaragoza (Spain))

    2008-08-15

    The overall objectives of the hydrogeochemical description for Forsmark are to establish a detailed understanding of the hydrogeochemical conditions at the site and to develop models that fulfil the needs identified by the safety assessment groups during the site investigation phase. Issues of concern to safety assessment are radionuclide transport and technical barrier behaviour, both of which are dependent on the chemistry of groundwater and pore water and their evolution with time. The work has involved the development of descriptive and mathematical models for groundwaters in relation to rock domains, fracture domains and deformation zones. Past climate changes are one of the major driving forces for hydrogeochemical changes and therefore of fundamental importance for understanding the palaeohydrogeological, palaeohydrogeochemical and present evolution of groundwater in the crystalline bedrock of the Fennoscandian Shield. Understanding current undisturbed hydrochemical conditions at the proposed repository site is important when predicting future changes in groundwater chemistry. The causes behind of copper corrosion and/or bentonite degradation are of particular interest as they may jeopardise the long-term integrity of the planned SKB repository system. Thus, the following variables are considered for the hydrogeochemical site descriptive modelling: pH, Eh, sulphur species, iron, manganese, carbonate, phosphate, nitrogen species, total dissolved solids (TDS), isotopes, colloids, fulvic and humic acids and microorganisms. In addition, dissolved gases (e.g. carbon dioxide, methane and hydrogen) are of interest because of their likely participation in microbial reactions. In this series of reports, the final hydrogeochemical evaluation work of the site investigation at the Forsmark site, is presented. The work was conducted by SKB's hydrogeochemical project group, ChemNet, which consists of independent consultants and university researchers with expertise

  18. Water-rock interaction modelling and uncertainties of mixing modelling. SDM-Site Forsmark

    International Nuclear Information System (INIS)

    Gimeno, Maria J.; Auque, Luis F.; Gomez, Javier B.; Acero, Patricia

    2008-08-01

    The overall objectives of the hydrogeochemical description for Forsmark are to establish a detailed understanding of the hydrogeochemical conditions at the site and to develop models that fulfil the needs identified by the safety assessment groups during the site investigation phase. Issues of concern to safety assessment are radionuclide transport and technical barrier behaviour, both of which are dependent on the chemistry of groundwater and pore water and their evolution with time. The work has involved the development of descriptive and mathematical models for groundwaters in relation to rock domains, fracture domains and deformation zones. Past climate changes are one of the major driving forces for hydrogeochemical changes and therefore of fundamental importance for understanding the palaeohydrogeological, palaeohydrogeochemical and present evolution of groundwater in the crystalline bedrock of the Fennoscandian Shield. Understanding current undisturbed hydrochemical conditions at the proposed repository site is important when predicting future changes in groundwater chemistry. The causes behind of copper corrosion and/or bentonite degradation are of particular interest as they may jeopardise the long-term integrity of the planned SKB repository system. Thus, the following variables are considered for the hydrogeochemical site descriptive modelling: pH, Eh, sulphur species, iron, manganese, carbonate, phosphate, nitrogen species, total dissolved solids (TDS), isotopes, colloids, fulvic and humic acids and microorganisms. In addition, dissolved gases (e.g. carbon dioxide, methane and hydrogen) are of interest because of their likely participation in microbial reactions. In this series of reports, the final hydrogeochemical evaluation work of the site investigation at the Forsmark site, is presented. The work was conducted by SKB's hydrogeochemical project group, ChemNet, which consists of independent consultants and university researchers with expertise in

  19. The use of mechanistic descriptions of algal growth and zooplankton grazing in an estuarine eutrophication model

    Science.gov (United States)

    Baird, M. E.; Walker, S. J.; Wallace, B. B.; Webster, I. T.; Parslow, J. S.

    2003-03-01

    A simple model of estuarine eutrophication is built on biomechanical (or mechanistic) descriptions of a number of the key ecological processes in estuaries. Mechanistically described processes include the nutrient uptake and light capture of planktonic and benthic autotrophs, and the encounter rates of planktonic predators and prey. Other more complex processes, such as sediment biogeochemistry, detrital processes and phosphate dynamics, are modelled using empirical descriptions from the Port Phillip Bay Environmental Study (PPBES) ecological model. A comparison is made between the mechanistically determined rates of ecological processes and the analogous empirically determined rates in the PPBES ecological model. The rates generally agree, with a few significant exceptions. Model simulations were run at a range of estuarine depths and nutrient loads, with outputs presented as the annually averaged biomass of autotrophs. The simulations followed a simple conceptual model of eutrophication, suggesting a simple biomechanical understanding of estuarine processes can provide a predictive tool for ecological processes in a wide range of estuarine ecosystems.

  20. A Bayesian belief network approach for assessing uncertainty in conceptual site models at contaminated sites

    DEFF Research Database (Denmark)

    Thomsen, Nanna Isbak; Binning, Philip John; McKnight, Ursula S.

    2016-01-01

    the most important site-specific features and processes that may affect the contaminant transport behavior at the site. However, the development of a CSM will always be associated with uncertainties due to limited data and lack of understanding of the site conditions. CSM uncertainty is often found...... to be a major source of model error and it should therefore be accounted for when evaluating uncertainties in risk assessments. We present a Bayesian belief network (BBN) approach for constructing CSMs and assessing their uncertainty at contaminated sites. BBNs are graphical probabilistic models...... that are effective for integrating quantitative and qualitative information, and thus can strengthen decisions when empirical data are lacking. The proposed BBN approach facilitates a systematic construction of multiple CSMs, and then determines the belief in each CSM using a variety of data types and/or expert...

  1. Mass discharge estimation from contaminated sites: Multi-model solutions for assessment of conceptual uncertainty

    Science.gov (United States)

    Thomsen, N. I.; Troldborg, M.; McKnight, U. S.; Binning, P. J.; Bjerg, P. L.

    2012-04-01

    Mass discharge estimates are increasingly being used in the management of contaminated sites. Such estimates have proven useful for supporting decisions related to the prioritization of contaminated sites in a groundwater catchment. Potential management options can be categorised as follows: (1) leave as is, (2) clean up, or (3) further investigation needed. However, mass discharge estimates are often very uncertain, which may hamper the management decisions. If option 1 is incorrectly chosen soil and water quality will decrease, threatening or destroying drinking water resources. The risk of choosing option 2 is to spend money on remediating a site that does not pose a problem. Choosing option 3 will often be safest, but may not be the optimal economic solution. Quantification of the uncertainty in mass discharge estimates can therefore greatly improve the foundation for selecting the appropriate management option. The uncertainty of mass discharge estimates depends greatly on the extent of the site characterization. A good approach for uncertainty estimation will be flexible with respect to the investigation level, and account for both parameter and conceptual model uncertainty. We propose a method for quantifying the uncertainty of dynamic mass discharge estimates from contaminant point sources on the local scale. The method considers both parameter and conceptual uncertainty through a multi-model approach. The multi-model approach evaluates multiple conceptual models for the same site. The different conceptual models consider different source characterizations and hydrogeological descriptions. The idea is to include a set of essentially different conceptual models where each model is believed to be realistic representation of the given site, based on the current level of information. Parameter uncertainty is quantified using Monte Carlo simulations. For each conceptual model we calculate a transient mass discharge estimate with uncertainty bounds resulting from

  2. An Efficient Explicit-time Description Method for Timed Model Checking

    Directory of Open Access Journals (Sweden)

    Hao Wang

    2009-12-01

    Full Text Available Timed model checking, the method to formally verify real-time systems, is attracting increasing attention from both the model checking community and the real-time community. Explicit-time description methods verify real-time systems using general model constructs found in standard un-timed model checkers. Lamport proposed an explicit-time description method using a clock-ticking process (Tick to simulate the passage of time together with a group of global variables to model time requirements. Two methods, the Sync-based Explicit-time Description Method using rendezvous synchronization steps and the Semaphore-based Explicit-time Description Method using only one global variable were proposed; they both achieve better modularity than Lamport's method in modeling the real-time systems. In contrast to timed automata based model checkers like UPPAAL, explicit-time description methods can access and store the current time instant for future calculations necessary for many real-time systems, especially those with pre-emptive scheduling. However, the Tick process in the above three methods increments the time by one unit in each tick; the state spaces therefore grow relatively fast as the time parameters increase, a problem when the system's time period is relatively long. In this paper, we propose a more efficient method which enables the Tick process to leap multiple time units in one tick. Preliminary experimental results in a high performance computing environment show that this new method significantly reduces the state space and improves both the time and memory efficiency.

  3. COPS model estimates of LLEA availability near selected reactor sites

    International Nuclear Information System (INIS)

    Berkbigler, K.P.

    1979-11-01

    The COPS computer model has been used to estimate local law enforcement agency (LLEA) officer availability in the neighborhood of selected nuclear reactor sites. The results of these analyses are presented both in graphic and tabular form in this report

  4. Fixed site neutralization model programmer's manual. Volume II

    International Nuclear Information System (INIS)

    Engi, D.; Chapman, L.D.; Judnick, W.; Blum, R.; Broegler, L.; Lenz, J.; Weinthraub, A.; Ballard, D.

    1979-12-01

    This report relates to protection of nuclear materials at nuclear facilities. This volume presents the source listings for the Fixed Site Neutralization Model and its supporting modules, the Plex Preprocessor and the Data Preprocessor

  5. Wind turbine blockset in Saber. General overview and description of the models

    DEFF Research Database (Denmark)

    Iov, Florin; Timbus, Adrian Vasile; Hansen, Anca Daniela

    This report presents a new developed Saber Toolbox for wind turbine applications. This toolbox has been developed during the research project “Simulation Platform to model, optimize and design wind turbines”. The report provides a quick overview of the Saber and then explains the structure...... of this simulation package, which is different than other tools e.g. Matlab/Simulink. Then the structure of the toolbox is shown as well as the description of the developed models. The main focus here is to underline the special structure of the models, which are a mixture of Saber built-in blocks and new developed...... blocks. Since the developed models are based on Saber built-in blocks, a description of the libraries from Saber is given. Then some simulation results using the developed models are shown. Finally some general conclusions regarding this new developed Toolbox as well as some directions for future work...

  6. Wind Turbine Blockset in Saber. General Overview and Description of the Model

    DEFF Research Database (Denmark)

    Iov, Florin; Timbus, Adrian Vasile; Hansen, A. D.

    This report presents a new developed Saber Toolbox for wind turbine applications. This toolbox has been developed during the research project ?Simulation Platform to model, optimize and design wind turbines?. The report provides a quick overview of the Saber and then explains the structure...... of this simulation package, which is different than other tools e.g. Matlab/Simulink. Then the structure of the toolbox is shown as well as the description of the developed models. The main focus here is to underline the special structure of the models, which are a mixture of Saber built-in blocks and new developed...... blocks. Since the developed mode