Biogas production from UASB and polyurethane carrier reactors treating sisal processing wastewater

Energy Technology Data Exchange (ETDEWEB)

Rubindamayugi, M.S.T.; Salakana, L.K.P. [Univ. of Dar es Salaam, Faculty of Science, Applied Microbiology Unit (Tanzania, United Republic of)

1997-12-31

The fundamental benefits which makes anaerobic digestion technology (ADT) attractive to the poor developing include the low cost and energy production potential of the technology. In this study the potential of using UASB reactor and Polyurethane Carrier Reactor (PCR) as pollution control and energy recovery systems from sisal wastewater were investigated in lab-scale reactors. The PCR demonstrated the shortest startup period, whereas the UASB reactor showed the highest COD removal efficiency 79%, biogas production rate (4.5 l biogas/l/day) and process stability than the PCR under similar HRT of 15 hours and OLR of 8.2 g COD/l/day. Both reactor systems became overloaded at HRT of 6 hours and OLR of 15.7 g COD/l/day, biogas production ceased and reactors acidified to pH levels which are inhibiting to methanogenesis. Based on the combined results on reactor performances, the UASB reactor is recommended as the best reactor for high biogas production and treatment efficiency. It was estimated that a large-scale UASB reactor can be designed under the same loading conditions to produce 2.8 m{sup 3} biogas form 1 m{sup 3} of wastewater of 5.16 kg COD/m{sup 3}. Wastewater from one decortication shift can produce 9,446 m{sup 3} og biogas. The energy equivalent of such fuel energy is indicated. (au)

Durability of Cement Composites Reinforced with Sisal Fiber

Science.gov (United States)

Wei, Jianqiang

This dissertation focuses mainly on investigating the aging mechanisms and degradation kinetics of sisal fiber, as well as the approaches to mitigate its degradation in the matrix of cement composites. In contrast to previous works reported in the literature, a novel approach is proposed in this study to directly determine the fiber's degradation rate by separately studying the composition changes, mechanical and physical properties of the embedded sisal fibers. Cement hydration is presented to be a crucial factor in understanding fiber degradation behavior. The degradation mechanisms of natural fiber consist of mineralization of cell walls, alkali hydrolysis of lignin and hemicellulose, as well as the cellulose decomposition which includes stripping of cellulose microfibrils and alkaline hydrolysis of amorphous regions in cellulose chains. Two mineralization mechanisms, CH-mineralization and self-mineralization, are proposed. The degradation kinetics of sisal fiber in the cement matrix are also analyzed and a model to predict the degradation rate of cellulose for natural fiber embedded in cement is outlined. The results indicate that the time needed to completely degrade the cellulose in the matrix with cement replacement by 30wt.% metakaolin is 13 times longer than that in pure cement. A novel and scientific method is presented to determine accelerated aging conditions, and to evaluating sisal fiber's degradation rate and durability of natural fiber-reinforced cement composites. Among the static aggressive environments, the most effective approach for accelerating the degradation of natural fiber in cement composites is to soak the samples or change the humidity at 70 °C and higher temperature. However, the dynamic wetting and drying cycling treatment has a more accelerating effect on the alkali hydrolysis of fiber's amorphous components evidenced by the highest crystallinity indices, minimum content of holocellulose, and lowest tensile strength. Based on the

Propriedades mecânicas de tração de compósitos poliéster/tecidos híbridos sisal/vidro Properties of polyester/hibrid sisal-glass fabrics

Directory of Open Access Journals (Sweden)

Laura H. de Carvalho

2006-03-01

Full Text Available O desempenho e o custo de compósitos podem ser alterados por hibridização e, neste sentido, é relativamente comum o uso combinado de fibras e reforços minerais no desenvolvimento destes materiais. No presente trabalho o desempenho mecânico de compósitos poliéster insaturado/ tecidos híbridos sisal-vidro foram investigados em função do teor de fibra e direção do teste. Foram confeccionados três tecidos híbridos (com 30, 40 e 50% em peso de vidro com fios de sisal no urdume e fibras de vidro na trama. Os compósitos foram moldados por compressão à temperatura ambiente com os tecidos alinhados. Os resultados indicam que houve um aumento nas propriedades mecânicas de tração de todos os compósitos com o aumento do teor de fibras. Para os compósitos reforçados por tecidos com baixo teor de fibra de vidro, as propriedades tenderam a ser mais elevadas quando os testes foram conduzidos na direção do sisal, enquanto que para os tecidos com elevado teor de vidro, o oposto foi observado. Estes comportamentos foram associados ao teor de fibra de vidro na direção do teste e ao diâmetro das fibras de sisal. Em baixos teores de fibra o sisal agiria como inclusão ou defeito, prejudicando as propriedades mecânicas; em elevados teores as propriedades do vidro suplantariam os defeitos provocados pelo sisal.Hybridization can alter both mechanical performance and cost of polymer composites, and novel composite materials can be obtained by the combination of both fibrous and mineral reinforcements. In the present work the mechanical performance of unsaturated polyester/hybrid sisal-glass fabrics was determined as a function of fibre content and test direction. Three different hybrid fabrics (30, 40 and 50% w/w glass content with sisal strings in the warp and glass roving in the weft were hand weaved. Aligned fabric compression moulded composites were obtained at room temperature. The results showed enhanced properties with fibre content

Antimicrobial activity of Agave sisalana

African Journals Online (AJOL)

STORAGESEVER

2009-11-16

Nov 16, 2009 ... cancer treatment, transplantation or are immuno- suppressed for ... machine after the decortication process of the leaves of A. sisalana in a sisal .... Composition and antimicrobial activity of the essential oils of two Origanum ...

Improving degradation resistance of sisal fiber in concrete through fiber surface treatment

Science.gov (United States)

Wei, Jianqiang; Meyer, Christian

2014-01-01

As part of an ongoing effort to improve the sustainability of reinforced concrete, recycled concrete aggregate is being considered together with natural fibers such as sisal fiber as replacement of synthetic reinforcement. Since natural fibers are known to undergo potential deterioration in the alkaline cement matrix especially in outdoor erosive environment, they need to be treated to improve their durability. This paper describes two such methods (thermal and Na2CO3 treatment) and evaluates their effects on the degradation resistance of sisal fiber and durability of sisal fiber-reinforced concrete with recycled concrete aggregate. Concrete specimens were subjected to cycles of wetting and drying to accelerate aging. The microstructure, tensile strength and Young's modulus of sisal fiber as well as the weight loss of the composite were evaluated. Of primary interest were the effects on compressive and splitting tensile strength of sisal fiber-reinforced concrete. Thermal treatment and Na2CO3 surface treatment were shown to improve the durability of the composite as measured by splitting tensile strength by 36.5% and 46.2% and the compressive strength by 31.1% and 45.4%, respectively. The mechanisms of these two treatment methods were also analyzed. The thermal treatment achieved improvement of cellulose's crystallization, which ensured the initial strength and improved durability of sisal fiber. A layer consisting of calcium carbonate sediments, which protects the internals of a fiber from the strong alkali solution formed in the cement hydration process, was formed and filled in pits and cavities on the Na2CO3 treated sisal fiber's surface to improve their corrosion resistance and durability and reduced the detrimental effects of Na+ ions on concrete.

Cultivation of three types of indigenous wild edible mushrooms ...

African Journals Online (AJOL)

STORAGESEVER

2008-12-17

Dec 17, 2008 ... they generate adverse environmental and economic effects related to their .... (i) Sisal decortication residue was used instead of cereal straws. ... diameter of 6 mm and there were 50 holes on the entire plastic sheet. The holes ...

Life cycle assessment of sisal fibre – Exploring how local practices can influence environmental performance

NARCIS (Netherlands)

Broeren, M.L.M.; Dellaert, S.N.C.; Cok, B.; Patel, M.K.; Worrell, E.; Shen, L.

2017-01-01

Sisal fibre can potentially replace glass fibre in natural fibre composites. This study focuses on the environmental performance of sisal fibre production by quantifying the greenhouse gas (GHG) emissions and energy use of producing sisal fibre in Tanzania and Brazil using life cycle assessment

Infiltração de sal de alumínio em fibras de sisal para obtenção de fibras de alumina Infiltration of aluminum salt into sisal to produce alumina fibers

Directory of Open Access Journals (Sweden)

T. E. Andrade Jr.

2005-03-01

Full Text Available O sisal é um recurso estratégico para a região Nordeste e, particularmente, para o estado do Rio Grande do Norte, por ser uma cultura renovável e adaptada às condições do semi-árido. Em virtude das condições adversas de clima e solo, o sisal é, em algumas regiões, o único produto agrícola rentável passível de plantio. Agregar valor aos produtos manufaturados a partir do sisal contribui não só para o desenvolvimento científico e tecnológico da região, como também para a geração de renda para a população dos municípios potiguares produtores de sisal. Da planta extraem-se fibras ligninocelulósicas utilizadas na produção artesanal de cordas e industrial de mantas e tapetes. Uma outra alternativa é o aproveitamento da estrutura da fibra para a produção de fibras de alumina (Al2O3 pela biomodelagem. Este processo consiste na reprodução da estruturas natural do material de partida. O objetivo deste trabalho foi estudar as condições de infiltração da fibra de sisal com sal de alumínio para posterior conversão da estrutura em fibras de alumina. Inicialmente, as fibras de sisal foram pré-tratadas com hidróxido de sódio, infiltradas com uma solução saturada de sal de alumínio (Al2Cl6 e sinterizadas entre 1400 °C e 1650 °C. A caracterização das fibras de alumina foi feita por difração de raios X e microscopia eletrônica de varredura. Os resultados mostraram a conversão completa apenas da superfície da fibra de sisal em alfa-Al2O3, resultando em baixa resistência ao manuseio. Novos métodos de infiltração são propostos com o objetivo de reproduzir-se a estrutura interna da fibra de sisal, resultando em fibras materiais com melhor resistência mecânica.Sisal is a renewable agricultural resource adapted to the hostile climatic and soil conditions particularly encountered in the semi-arid areas of the state of Rio Grande do Norte, located in Northeastern Brazil. Consequently, sisal has played a

Efficacy of Thermally Conditioned Sisal FRP Composite on the Shear Characteristics of Reinforced Concrete Beams

Directory of Open Access Journals (Sweden)

Tara Sen

2013-01-01

Full Text Available The development of commercially viable composites based on natural resources for a wide range of applications is on the rise. Efforts include new methods of production and the utilization of natural reinforcements to make biodegradable composites with lignocellulosic fibers, for various engineering applications. In this work, thermal conditioning of woven sisal fibre was carried out, followed by the development of woven sisal fibre reinforced polymer composite system, and its tensile and flexural behaviour was characterized. It was observed that thermal conditioning improved the tensile strength and the flexural strength of the woven sisal fibre composites, which were observed to bear superior values than those in the untreated ones. Then, the efficacy of woven sisal fibre reinforced polymer composite for shear strengthening of reinforced concrete beams was evaluated using two types of techniques: full and strip wrapping techniques. Detailed analysis of the load deflection behaviour and fracture study of reinforced concrete beams strengthened with woven sisal under shearing load were carried out, and it was concluded that woven sisal FRP strengthened beams, underwent very ductile nature of failure, without any delamination or debonding of sisal FRP, and also increased the shear strength and the first crack load of the reinforced concrete beams.

Mechanical and thermal properties of water glass coated sisal fibre-reinforced polypropylene composite

CSIR Research Space (South Africa)

Phiri, G

2012-10-01

Full Text Available ?C). Figure 1 shows the processing steps followed to produce composite samples. Up to 15% fibre loading could be achieved and the sisal fibres were coated with water glass to improve fire resistance. In order to improve the adhesion between sisal... preparation process: (A) WG coated fibre, (B) High speed granulator, (C) Composite granules, (D) Single screw extruder, (E) Injection moulder and (F) Composite samples (dumbbells) Mechanical and thermal properties of water glass coated sisal fi bre...

Biogas systems for sisal and other agro-industrial residues

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G [Danish Technological Inst., Section for Biotechnology, Taastrup (Denmark)

1998-12-31

Most of the East-African agro-industries are generating very large quantities of organic residues from production and processing of different crops. In the East-African Region the most important of these crops are: Sisal, Sugar, Coffee, Cashew nuts and Pineapple. In other 3. world countries, Palm oil and Cassava (Tapioca starch) processing are main producers of organic waste products. Moreover, large quantities of organic residues are generated from other food processing activities like breweries, consumption of bananas etc. The following pages give examples of setups and system designs of anaerobic treatment systems for some of the residues mentioned above. When considering anaerobic treatment of sisal residues, which constitutes the main agro-industrial biomass resource in Tanzania, two major issues should be considered: Optimal reactor set-up and performance; And optionally, potential methods for pre-treatment of fibre fraction in order to increase the methane yield. The sisal liquid residues are degraded very fast and efficiently in UASB systems. At COD loading rates less than 11 kg COD/m{sup 3} x day, the reduction in organic matter is more than 90% and methane yields obtained are between 373 and 377 ml CH{sub 4}/g COD reduced. The treatment of sisal solid residues in CSTR systems has been examined both at mesophilic (37 deg. C) and thermophilic temperatures (55 deg. C.). (EG)

Biogas systems for sisal and other agro-industrial residues

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G. [Danish Technological Inst., Section for Biotechnology, Taastrup (Denmark)

1997-12-31

Most of the East-African agro-industries are generating very large quantities of organic residues from production and processing of different crops. In the East-African Region the most important of these crops are: Sisal, Sugar, Coffee, Cashew nuts and Pineapple. In other 3. world countries, Palm oil and Cassava (Tapioca starch) processing are main producers of organic waste products. Moreover, large quantities of organic residues are generated from other food processing activities like breweries, consumption of bananas etc. The following pages give examples of setups and system designs of anaerobic treatment systems for some of the residues mentioned above. When considering anaerobic treatment of sisal residues, which constitutes the main agro-industrial biomass resource in Tanzania, two major issues should be considered: Optimal reactor set-up and performance; And optionally, potential methods for pre-treatment of fibre fraction in order to increase the methane yield. The sisal liquid residues are degraded very fast and efficiently in UASB systems. At COD loading rates less than 11 kg COD/m{sup 3} x day, the reduction in organic matter is more than 90% and methane yields obtained are between 373 and 377 ml CH{sub 4}/g COD reduced. The treatment of sisal solid residues in CSTR systems has been examined both at mesophilic (37 deg. C) and thermophilic temperatures (55 deg. C.). (EG)

THE USE OF SISAL FIBRE AS REINFORCEMENT IN CEMENT BASED COMPOSITES

Directory of Open Access Journals (Sweden)

Romildo Dias Tolêdo Filho

1999-08-01

Full Text Available ABSTRACT The inclusion of fibre reinforcement in concrete, mortar and cement paste can enhance many of the engineering properties of the basic materials, such as fracture toughness, flexural strength and resistance to fatigue, impact, thermal shock and spalling. In recent years, a great deal of interest has been created worldwide on the potential applications of natural fibre reinforced, cement based composites. Investigations have been carried out in many countries on various mechanical properties, physical performance and durability of cement based matrices reinforced with naturally occurring fibres including sisal, coconut, jute, bamboo and wood fibres. These fibres have always been considered promising as reinforcement of cement based matrices because of their availability, low cost and low consumption of energy. In this review, the general properties of the composites are described in relation to fibre content, length, strength and stiffness. A chronological development of sisal fibre reinforced, cement based matrices is reported and experimental data are provided to illustrate the performance of sisal fibre reinforced cement composites. A brief description on the use of these composite materials as building products has been included. The influence of sisal fibres on the development of plastic shrinkage in the pre-hardened state, on tensile, compressive and bending strength in the hardened state of mortar mixes is discussed. Creep and drying shrinkage of the composites and the durability of natural fibres in cement based matrices are of particular interest and are also highlighted. The results show that the composites reinforced with sisal fibres are reliable materials to be used in practice for the production of structural elements to be used in rural and civil construction. This material could be a substitute asbestos-cement composite, which is a serious hazard to human and animal health and is prohibited in industrialized countries. The

Properties of SBS and sisal fiber composites: ecological material for shoe manufacturing

Directory of Open Access Journals (Sweden)

José Carlos Krause de Verney

2008-12-01

Full Text Available The worldwide trend toward using cheap, atoxic and durable materials from renewable resources contributes to sustainable development. Thus, the investigation of the potential use of vegetal fibers as reinforcing agent in polymeric composites has gained new significance. Sisal fiber has emerged as a reinforcing material for polymers used in automobile, footwear and civil industries. In this work, properties such as hardness, tensile strength and tear strength of polymer composites composed by block copolymer styrene-butadiene-styrene (SBS and 5, 10 and 20% by weight of sisal fiber were evaluated. The influence of conventional polymer processing techniques such as single-screw and double-screw extrusion, as well as the addition of coupling agent on the composite mechanical performance was investigated. Also, the morphology and thermal stability of the composites were analyzed. The addition of 2 wt. (% maleic anhydride as coupling agent between sisal fiber and SBS has improved the composite mechanical performance and the processing in a double-screw extruder has favored the sisal fiber distribution in the SBS matrix.

Fibra de sisal como envoltório na drenagem agrícola

Directory of Open Access Journals (Sweden)

Viviane F. Silva

2014-06-01

Full Text Available O trabalho foi realizado objetivando analisar o desempenho do sistema de drenagem com fibra de sisal envolto orgânico como material alternativo.  A pesquisa foi realizada no Laboratório de Engenharia de Irrigação e Drenagem da Universidade Federal de Campina Grande. Usando-se um sistema experimental composto de nove tanques construídos de alvenaria e impermeabilizados internamente. Os tratamentos foram dispostos em um arranjo fatorial com três tipos de tubos, Drenoflex, Kananet e tubo de PVC liso próprio para Esgoto envolto com fibra de sisal num delineamento inteiramente casualizado com três repetições. Foram avaliados a carga hidráulica de entrada (he, fluxo(q e resistência de entrada(re e analisados  estatisticamente, utilizando-se o software ASSISTAT . A comparação dos tubos Drenoflex, PVC liso e Kananet envolto com fibra de sisal, as médias da carga hidráulica na entrada para os tubos variando os valores de 0,40486 a 0,35543, sendo significativo para o tubo Kananet, devido possuir furos maiores facilitando assim a passagem da água pelo tubo. E em relação à resistência de entrada na interação entre os tubos drenantes e a fibra de sisal diferiu estatisticamente com o tubo PVC liso. O desempenho do sistema drenante com envolto de fibra de sisal é considerado muito bom.

Propriedades de compósitos híbridos de borracha nitrílica, fibras de sisal e carbonato de cálcio Properties of nitrile rubber, sisal fiber and calcium carbonate hybrid composites

Directory of Open Access Journals (Sweden)

Marco A. Iozzi

2004-06-01

Full Text Available Neste trabalho, estudou-se a influência do teor de carbonato de cálcio nas propriedades mecânicas e térmicas da borracha nitrílica, e do comprimento das fibras de sisal nas propriedades mecânicas dos compósitos de borracha nitrílica/fibras de sisal, e borracha nitrílica/carbonato de cálcio/fibras de sisal. Os materiais foram caracterizados através de ensaios mecânicos de resistência à tração, microscopia eletrônica de varredura (MEV, e termogravimetria (TG. O melhor desempenho mecânico dos compósitos com as fibras curtas aleatoriamente distribuídas foi obtido para o comprimento das fibras de 6 mm, e teor de carbonato de 67 pcr. A análise térmica mostrou que os compósitos são estáveis até cerca de 300 °C. Os resultados mostraram que os materiais obtidos possuem uma boa relação custo/benefício tornando promissora sua utilização.In this work, nitrile rubber with sisal fibers composites and nitrile rubber with calcium carbonate and sisal fibers composites were developed. The influence from the calcium carbonate amount and size of sisal fibers on the composite properties was studied. The composites, with short fibers randomly distributed, were characterized by mechanical analysis, scanning electron microscopy (SEM, and thermogravimetric analysis (TGA. The optimal size of sisal fibers to reinforce the nitrile matrix was 6 mm. The ideal volume of calcium carbonate was 67 phr. TGA analysis demonstrated that the composites are stable up to 300 °C. The materials developed have a good cost/benefits relation, being therefore promising their utilization.

Modified single-port non-intubated video-assisted thoracoscopic decortication in high-risk parapneumonic empyema patients.

Science.gov (United States)

Hsiao, Chen-Hao; Chen, Ke-Cheng; Chen, Jin-Shing

2017-04-01

Parapneumonic empyema patients with coronary artery disease and reduced left ventricular ejection fraction are risky to receive surgical decortication under general anesthesia. Non-intubated video-assisted thoracoscopy surgery is successfully performed to avoid complications of general anesthesia. We performed single-port non-intubated video-assisted flexible thoracoscopy surgery in an endoscopic center. In this study, the possible role of our modified surgery to treat fibrinopurulent stage of parapneumonic empyema with high operative risks is investigated. We retrospectively reviewed fibrinopurulent stage of parapneumonic empyema patients between July 2011 and June 2014. Thirty-three patients with coronary artery disease and reduced left ventricular ejection fraction were included in this study. One group received tube thoracostomy, and the other group received single-port non-intubated video-assisted flexible thoracoscopy surgery decortication. Patient demographics, characteristics, laboratory findings, etiology, and treatment outcomes were compared. Mean age of 33 patients (24 males, 9 females) was 76.2 ± 9.7 years. Twelve patients received single-port non-intubated video-assisted flexible thoracoscopy surgery decortication, and 21 patients received tube thoracostomy. Visual analog scale scores on postoperative first hour and first day were not significantly different in two groups (p value = 0.5505 and 0.2750, respectively). Chest tube drainage days, postoperative fever subsided days, postoperative hospital days, and total length of stay were significantly short in single-port non-intubated video-assisted flexible thoracoscopy surgery decortication (p value = 0.0027, 0.0001, 0.0009, and 0.0065, respectively). Morbidities were low, and mortality was significantly low (p value = 0.0319) in single-port non-intubated video-assisted flexible thoracoscopy surgery decortication. Single-port non-intubated video-assisted flexible thoracoscopy surgery

Mechanical characterization of sisal reinforced cement mortar

Directory of Open Access Journals (Sweden)

R. Fujiyama

2014-01-01

Full Text Available This work aims at evaluating the mechanical behavior of sisal fiber reinforced cement mortar. The composite material was produced from a mixture of sand, cement, and water. Sisal fibers were added to the mixture in different lengths. Mechanical characterization of both the composite and the plain mortar was carried out using three point bend, compression, and impact tests. Specimens containing notches of different root radii were loaded in three point bending in an effort to determine the effect of the fibers on the fracture toughness of the material. The results obtained indicate that, while fiber reinforcement leads to a decrease in compressive strength, J-integral calculations at maximum load for the different notch root radii have indicated, particularly for the case of long fibers, a significant superiority of the reinforced material in comparison with the plain cement mortar, in consistence with the impact test data.

Insulation Characteristics of Sisal Fibre/Epoxy Composites

Directory of Open Access Journals (Sweden)

A. Shalwan

2017-01-01

Full Text Available Using natural fibres in civil engineering is the aim of many industrial and academics sectors to overcome the impact of synthetic fibres on environments. One of the potential applications of natural fibres composites is to be implemented in insulation components. Thermal behaviour of polymer composites based on natural fibres is recent ongoing research. In this article, thermal characteristics of sisal fibre reinforced epoxy composites are evaluated for treated and untreated fibres considering different volume fractions of 0–30%. The results revealed that the increase in the fibre volume fraction increased the insulation performance of the composites for both treated and untreated fibres. More than 200% insulation rate was achieved at the volume fraction of 20% of treated sisal fibres. Untreated fibres showed about 400% insulation rate; however, it is not recommended to use untreated fibres from mechanical point of view. The results indicated that there is potential of using the developed composites for insulation purposes.

Assessment of the mechanical properties of sisal fiber-reinforced silty clay using triaxial shear tests.

Science.gov (United States)

Wu, Yankai; Li, Yanbin; Niu, Bin

2014-01-01

Fiber reinforcement is widely used in construction engineering to improve the mechanical properties of soil because it increases the soil's strength and improves the soil's mechanical properties. However, the mechanical properties of fiber-reinforced soils remain controversial. The present study investigated the mechanical properties of silty clay reinforced with discrete, randomly distributed sisal fibers using triaxial shear tests. The sisal fibers were cut to different lengths, randomly mixed with silty clay in varying percentages, and compacted to the maximum dry density at the optimum moisture content. The results indicate that with a fiber length of 10 mm and content of 1.0%, sisal fiber-reinforced silty clay is 20% stronger than nonreinforced silty clay. The fiber-reinforced silty clay exhibited crack fracture and surface shear fracture failure modes, implying that sisal fiber is a good earth reinforcement material with potential applications in civil engineering, dam foundation, roadbed engineering, and ground treatment.

Assessment of the Mechanical Properties of Sisal Fiber-Reinforced Silty Clay Using Triaxial Shear Tests

Directory of Open Access Journals (Sweden)

Yankai Wu

2014-01-01

Full Text Available Fiber reinforcement is widely used in construction engineering to improve the mechanical properties of soil because it increases the soil’s strength and improves the soil’s mechanical properties. However, the mechanical properties of fiber-reinforced soils remain controversial. The present study investigated the mechanical properties of silty clay reinforced with discrete, randomly distributed sisal fibers using triaxial shear tests. The sisal fibers were cut to different lengths, randomly mixed with silty clay in varying percentages, and compacted to the maximum dry density at the optimum moisture content. The results indicate that with a fiber length of 10 mm and content of 1.0%, sisal fiber-reinforced silty clay is 20% stronger than nonreinforced silty clay. The fiber-reinforced silty clay exhibited crack fracture and surface shear fracture failure modes, implying that sisal fiber is a good earth reinforcement material with potential applications in civil engineering, dam foundation, roadbed engineering, and ground treatment.

Mechanical, Thermal Degradation, and Flammability Studies on Surface Modified Sisal Fiber Reinforced Recycled Polypropylene Composites

Directory of Open Access Journals (Sweden)

Arun Kumar Gupta

2012-01-01

Full Text Available The effect of surface treated sisal fiber on the mechanical, thermal, flammability, and morphological properties of sisal fiber (SF reinforced recycled polypropylene (RPP composites was investigated. The surface of sisal fiber was modified with different chemical reagent such as silane, glycidyl methacrylate (GMA, and O-hydroxybenzene diazonium chloride (OBDC to improve the compatibility with the matrix polymer. The experimental results revealed an improvement in the tensile strength to 11%, 20%, and 31.36% and impact strength to 78.72%, 77%, and 81% for silane, GMA, and OBDC treated sisal fiber reinforced recycled Polypropylene (RPP/SF composites, respectively, as compared to RPP. The thermogravimetric analysis (TGA, differential scanning calorimeter (DSC, and heat deflection temperature (HDT results revealed improved thermal stability as compared with RPP. The flammability behaviour of silane, GMA, and OBDC treated SF/RPP composites was studied by the horizontal burning rate by UL-94. The morphological analysis through scanning electron micrograph (SEM supports improves surface interaction between fiber surface and polymer matrix.

Efeito do tratamento das fibras nas propriedades do biocompósito de amido termoplástico/policaprolactona/sisal Effect of fiber treatments on properties of thermoplastic starch/polycaprolactone/sisal biocomposites

Directory of Open Access Journals (Sweden)

Adriana de Campos

2011-01-01

Full Text Available Fibras de sisal com quatro tratamentos, a saber: fibra lavada com água, lavada com cicloexano/etanol, tratamento alcalino (NaOH e tratamento com peróxido alcalino (branqueamento, foram incorporadas na blenda amido termoplástico/policaprolactona 80/20 (TPS/PCL. As propriedades morfológicas, mecânicas e térmicas dos biocompósitos TPS/PCL/Sisal foram analisadas. Os compósitos com a fibra branqueada apresentaram os melhores resultados de resistência à tração e estabilidade térmica. Verificou-se também melhora da adesão fibra-matriz no compósito com a fibra branqueada, com aumento de 145% na resistência à tração.Sisal fibers treated with four methods, namely washing with water, washing with cyclohexane/ethanol, alkali treatment (NaOH and bleaching (alkaline peroxide treatment, were incorporated in thermoplastic starch/polycaprolactone 80/20 (TPS/PCL samples. Morphological, mechanical and thermal properties of TPS/PCL/Sisal biocomposites were analysed. The best results were obtained with the composite using the bleached fiber, which had improved tensile strength and thermal stability. An increased adhesion between the fiber and matrix was also observed with the bleached fiber, with 145% increase in the tensile strength

Effects of wood saw dust ash admixed with treated sisal fibre on the geotechnical properties of lateritic soil

Directory of Open Access Journals (Sweden)

John Engbonye SANI

2017-12-01

Full Text Available The preliminary investigation conducted on the lateritic soil collected at Shika, Zaria shows that it falls under A-7-6 (10 classification for AASHTO (1986 and CL according to unified soil classification system USCS (ASTM 1992. The soil was treated with both wood saw dust ash (WSDA and treated sisal fiber, in stepped concentration of 0,2,4,6, and 8% for WSDA and 0, 0.25, 0.5, 0.75 and 1% treated sisal fibre by dry weight of soil using Standard proctor. The Sisal Fibre was treated with Sodium Borohydride (NaBH4 (1% wt/vol for 60 minutes at room temperature to remove the cellulose content present in the Fibre. Statistical analysis was carried out on the obtained results using XLSTART 2017 software and analysis of variance with the Microsoft Excel Analysis Tool Pak Software Package. The liquid limit (LL of the soil was found to be 48% while the plastic limit(PL is 21.27%. The maximum dry density(MDDhowever, decreases generally from a value of 1.85 Mg/m3 to 1.68Mg/m3 at 0.25% sisal fiber content/0% WSDA. It has its least value of 1.57Mg/m3 at 1% sisal fiber and 8% WSDA. The OMC increased from 18 % of the natural soil to 23.7% at 0.75% sisal fiber / 6% WSDA content. There was a general increase in the value of UCS of the soil-sisal fibre mixture with WSDA content from 100 kN/m2 of the natural soil to 696 kN/m2 at 0.75 % sisal fibre content / 6% WSDA. The UCS value met the standard of 687-1373 kN/m2 requirements of sub base for adequate lime and cement stabilization, respectively (Ingas and Metcalf 1972.

Striving for Diversity, Accessibility and Quality: Evaluating SiSAL Journal

Directory of Open Access Journals (Sweden)

Jo Mynard

2014-06-01

Full Text Available After establishing a journal, it is important to evaluate its progress to ensure that the principles that underpin its existence continue to be a priority. In this article, the author reports on measures that were used to evaluate Studies in Self-Access Learning (SiSAL Journal. The research was designed to investigate the three principles that the journal values: diversity, accessibility and quality. The results identified some successful factors such as accessibility and favourable perceptions of SiSAL Journal’s quality. However, the results also identified areas that could be improved to further increase diversity and to encourage submissions from more authors based in different locations.

Profiling application potential for alkali treated sisal fiber ...

African Journals Online (AJOL)

ATHARVA

research and development efforts in the composites fields as they offer properties superior in ... advantages of both the fiber and matrix (Carvallo et al, 2010). ..... et al., 2008, who indicated spiral fractures in coir fibers following decortication.

Characterization and treatment of sisal fiber residues for cement-based composite application

OpenAIRE

Lima,Paulo R. L.; Santos,Rogério J.; Ferreira,Saulo R.; Toledo Filho,Romildo D.

2014-01-01

Sisal fiber is an important agricultural product used in the manufacture of ropes, rugs and also as a reinforcement of polymeric or cement-based composites. However, during the fiber production process a large amount of residues is generated which currently have a low potential for commercial use. The aim of this study is to characterize the agricultural residues by the production and improvement of sisal fiber, called field bush and refugo and verify the potentiality of their use in the rein...

Caracterização química e estrutural de fibra de sisal da variedade Agave sisalana Chemical and structural characterization of sisal fibers from Agave sisalana variety

Directory of Open Access Journals (Sweden)

Adriana R. Martin

2009-01-01

Full Text Available Nos últimos anos, o interesse pelo uso de fibras naturais em materiais compósitos poliméricos tem aumentado significativamente. Neste trabalho foram investigadas as propriedades, químicas, físicas, térmicas e estruturais da fibra de sisal brasileira da variedade Agave sisalana. Nosso objetivo foi avaliar a qualidade e o desempenho desta fibra para aplicações industriais. Foram realizados ensaios de resistência à tração, análise da composição química, difração de raios X, e estudos por microscopia eletrônica de varredura (MEV ao longo do comprimento da fibra. A fibra de sisal brasileira apresentou propriedades mecânicas e térmicas dentro da faixa relatada na literatura, mostrando-se adequada para ser utilizada em materiais compósitos poliméricos.In recent years, the interest in the use of natural fibers in polymeric composite materials has increased significantly. In this work were investigated the structural, thermal, chemical, and physical properties of Brazilian sisal fiber from Agave sisalana variety. Our aim was to evaluate the quality and the performance of this fiber for industrial applications. Mechanical properties, chemical composition, X ray diffraction, and scanning electron microscopy (SEM have been investigated with fibers along their length. The Brazilian sisal fibers studied have exhibited mechanical and thermal properties within the range reported in the literature and were suitable for use in polymeric composites.

Antifungal effects of sisal leaf juice on Lasiodiplodia theobromae ...

African Journals Online (AJOL)

Among the nine varieties, the inhibition effects of hybrid 76416 and Agave americana were the best with absolute inhibition of all the leaf juice treatments against the mycelial growth, followed by Agave Amaniensis, Agave virdis, Agave angustifolia and Hybrid 11648. The inhibitory effect of some fresh juices would be cut ...

Profiling application potential for alkali treated sisal fiber ...

African Journals Online (AJOL)

The effect of alkali treatment on sisal fiber from the plant agave sisalana in appropriation for composite material application is presented. Effectiveness of the fiber's reinforcement potential within polypropylene (PP) matrix is evaluated through morphological analysis, crystallinity levels, and tensile, where ultimate tensile ...

Investigation on mechanical properties of woven alovera/sisal/kenaf ...

Indian Academy of Sciences (India)

1Department of Mechanical Engineering, Sri Sai Ram Institute of Technology, ... ASTM American Society for Testing and Materials ... stress [9]. Naturally the sisal fibres have the characteristics of higher wear ... In this research work an effort.

A multi-scale investigation of the mechanical behavior of durable sisal fiber cement composites

OpenAIRE

Silva, Flávio de Andrade; Toledo Filho, Romildo D.; Mobasher, Barzin; Chawla, Nikhilesh

2010-01-01

Durable sisal fiber cement composites reinforced with long unidirectional aligned fibers were developed and their mechanical behavior was characterized in a multi-scale level. Tensile tests were performed in individual sisal fibers. Weibull statistics were used to quantify the degree of variability in fiber strength at different gage lengths. The fiber-matrix pull-out behavior was evaluated at several curing ages and embedded lengths. The composite's mechanical response was measured under dir...

Study of the influence from chemical treatments of sisal fibers on the properties of composites with nitrile rubber

OpenAIRE

Iozzi, Marco A.; Martins, Gilson S.; Martins, Maria A.; Ferreira, Fábio C.; Job, Aldo E.; Mattoso, Luiz H. C.

2010-01-01

A influência de diferentes tratamentos das fibras de sisal nas propriedades dos compósitos de borracha nitrílica/fibras de sisal, e borracha nitrílica/carbonato de cálcio/fibras de sisal foi investigada. Os compósitos, com fibras curtas aleatoriamente distribuídas, foram processados em moinho de dois rolos e caracterizados através de ensaios mecânicos de resistência à tração, microscopia eletrônica de varredura (MEV), análise por termogravimetria (TG) e calorimetria exploratória diferencial (...

Resíduos de sisal como reforço em compósitos de polipropileno virgem e reciclado Virgin and recycled polypropylene composites reinforced with sisal by-product

Directory of Open Access Journals (Sweden)

Francisco Rosário

2011-01-01

Full Text Available Foram estudadas as propriedades térmicas e mecânicas de compósitos de polipropileno, virgem e reciclado, reforçados com 30% em massa de fibras residuais de sisal, assim como o perfil de processamento e a morfologia da matriz polimérica. Para tanto, foram determinadas a resistência à tração, o módulo de Young, alongamento na ruptura, e energia de impacto. As amostras também foram caracterizadas por MEV, DMTA e TG. Para ambos os compósitos de polipropileno, virgem e reciclado, com a adição das fibras, o alongamento na ruptura mostrou uma queda significativa, enquanto que a resistência à tração não sofreu grandes variações. Houve um aumento significativo nos valores de tração na ruptura e de energia de impacto com a adição das fibras de sisal na matriz de polipropileno. As análises térmicas mostraram ligações secundárias, como as ligações polares, entre as fibras e a matriz, concordando com o comportamento mecânico dos compósitos. Constatou-se que a temperatura de transição vítrea não variou após a adição da fibra.The mechanical and thermal properties of virgin and recycled polypropylene composites reinforced with 30% by mass of residual sisal fibers were studied, in addition to an analysis of the extrusion process and morphology of the polymeric matrix. Tensile strength, Young's modulus, elongation at break, and impact energy were determined. The samples were also characterized by SEM, DMTA and TG analyses. Elongation at break of the composites presented a significant decrease, while the tensile strength was not affected significantly by addition of sisal fibers. A significant increase was observed in the tension of rupture and in the impact energy of the composite reinforced with sisal fiber. The thermal analyses indicated secondary interactions, such as polar interactions, between the fibers and the matrix, consistent with the mechanical behavior of the composites. The glass transition temperature has not

Thermal performance of sisal fiber-cement roofing tiles for rural constructions Desempenho térmico de telhas de fibrocimento reforçadas com polpa de sisal para construções rurais

Directory of Open Access Journals (Sweden)

Gustavo Henrique Denzin Tonoli

2011-02-01

Full Text Available Roofing provides the main protection against direct solar radiation in animal housing. Appropriate thermal properties of roofing materials tend to improve the thermal comfort in the inner ambient. Nonasbestos fiber-cement roofing components reinforced with cellulose pulp from sisal (Agave sisalana were produced by slurry and dewatering techniques, with an optional addition of polypropylene fibers. Nonasbestos tiles were evaluated and compared with commercially available asbestos-cement sheets and ceramic tiles (frequently chosen as roofing materials for animal housing. Thermal conductivity and thermal diffusivity of tiles were determined by the parallel hot-wire method, along with the evaluation of the downside surface temperature. Cement-based components reinforced with sisal pulp presented better thermal performance at room temperature (25ºC, while those reinforced with sisal pulp added by polypropylene fibers presented better thermal performance at 60ºC. Non-asbestos cement tiles provided more efficient protection against radiation than asbestos corrugated sheets.O telhado fornece a principal proteção contra a radiação solar direta em galpões para animais. Propriedades térmicas apropriadas dos materiais contribuem para o melhor conforto térmico no interior das construções. Telhas sem amianto reforçadas com polpa de celulose de sisal (Agave sisalana e com adição opcional de fibras de polipropileno foram produzidas pela técnica de mistura e sucção do excesso de água. Telhas corrugadas de cimento amianto, telhas cerâmicas e telhas à base de cimento reforçadas com polpa de celulose (com ou sem adição de fibras sintéticas foram comparadas quanto às suas propriedades térmicas. A condutividade térmica e a difusividade térmica foram determinadas pelo método do fio quente paralelo, assim como a temperatura da superfície inferior das telhas foi avaliada em diferentes períodos. Telhas de cimento reforçados com polpa de

Mechanical and water absorption behaviour of banana/sisal reinforced hybrid composites

International Nuclear Information System (INIS)

Venkateshwaran, N.; ElayaPerumal, A.; Alavudeen, A.; Thiruchitrambalam, M.

2011-01-01

Highlights: → It explores the utilization of waste banana fiber. → Improving the mechanical property by hybridization. → Results show its usefulness to low cost application. -- Abstract: The tensile, flexural, impact and water absorption tests were carried out using banana/epoxy composite material. Initially, optimum fiber length and weight percentage were determined. To improve the mechanical properties, banana fiber was hybridised with sisal fiber. This study showed that addition of sisal fiber in banana/epoxy composites of up to 50% by weight results in increasing the mechanical properties and decreasing the moisture absorption property. Morphological analysis was carried out to observe fracture behaviour and fiber pull-out of the samples using scanning electron microscope.

COMPOSITE FRIEND SISAL / POLYESTER TREATED IN SURFACE

Directory of Open Access Journals (Sweden)

Jayna K. Dionisio Santos

2011-09-01

Full Text Available The use of composites in manufacturing equipment and products is taking a very important space in the industry in general. Moreover these materials have unique characteristics when analyzed separately from constituents who are part of them. However it is know that cares must be taken in their manufacture, as the use of appropriate process and the composition of each element, in addition to adherence fiber / matrix, which is a major factor in obtaining of the final mechanical strength of the product. One should also take into account whether the composites are environmentally friendly. For this reason, in this work, a composite partially ecological was made, using as reinforcement, a sisal woven and, as matrix, the polyester resin. Seeking to improve the adherence fiber / matrix, a treatment in sisal woven was performed with aqueous solution of sodium hydroxide (NaOH at a concentration of 3%. The composite subjected to this treatment presented, in bending test, a better mechanical performance, with an increase of 27% in the flexion strength and of 54% in maximum strain, but there was a reduction of about 15% in its flexural modulus.

VALORIZAÇÃO DOS RESÍDUOS DE SISAL: UMA PROPOSTA PARA A REGIÃO DO SEMIARIDO DO ESTADO DA BAHIA

Directory of Open Access Journals (Sweden)

Antonivalda Tosta Dias

2015-01-01

Full Text Available O presente estudo tem como objetivo apresentar uma proposta para a valorizaçãodos resíduos de sisal que reduza e/ou elimine o passivo ambiental existente naRegião Sisaleira da Bahia. Este trabalho foi desenvolvido em duas etapas. Naprimeira etapa, foi feito um diagnóstico visual dos problemas fitossanitáriosassociados ao beneficiamento do sisal na Comunidade Rose do município deSantaluz, complementado com análise das propriedades químicas dos solos(arenoso e argiloso em seis unidades produtivas, onde foram avaliados locaiscom ou sem o resíduo do sisal nas profundidades de 0 - 20cm e 20 - 40cm. Nasegunda etapa, foi montado um experimento de compostagem na UniversidadeEstadual de Feira de Santana, com os seguintes tratamentos: T! - resíduo desisal, T2 - resíduo de sisal + poda de árvores + urina humana + esterco de cabra,T3 - resíduo de sisal + poda de árvores + esterco de cabra e T4 - resíduo de sisal+ poda de árvores + urina humana + esterco de cabra. Estes resíduos foramdispostos em camadas de 20cm, exceto o tratamento T4, em que a matéria primafoi homogeneizada antes da montagem das pilhas. Foram avaliados osparâmetros físicos e químicos do composto formado. Os resultados encontradosna primeira etapa demonstram que não existe um local definitivo para odesfibramento do sisal que é descartado no campo, ocupando áreas antesprodutivas por mais de dois anos, tempo necessário para sua degradação. Oresíduo é um meio adequado para produção de moscas. O solo, por sua vez, érico em matéria orgânica, entretanto, o teor de nutrientes foi muito maior no localcom a presença do resíduo de sisal. O composto orgânico em todos ostratamentos apresentou teores de nutrientes e metais pesados de acordo com osvalores pré-estabelecidos pelo MAPA, com exceção do nitrogênio que ficouabaixo do exigido. É possível obter um composto orgânico de boa qualidade apartir da mistura de resíduos de sisal com outros componentes

Caracterização mecânica de laminados cimentíceos esbeltos reforçados com fibras de sisal Mechanical characterization of cement-based thin-walled laminates reinforced with sisal fibre

Directory of Open Access Journals (Sweden)

Paulo R. L. Lima

2007-12-01

Full Text Available Com a proibição progressiva do uso de fibras de asbesto na fabricação de laminados à base de cimento, novos produtos têm sido desenvolvidos para suprir esta demanda do setor construtivo. A utilização de fibras de sisal como substituto ao asbesto, além de ser uma proposta ecológica tem grande importância socioeconômica, pois agregará valor a um produto cultivado com sucesso no semi-árido nordestino. Produziram-se, neste trabalho, placas laminadas com matriz de argamassa reforçadas com fibras longas de sisal. Ensaios de flexão em três pontos foram realizados com o objetivo de se estudar a influência da adição de fibras (3%, do número de camadas (2 e 3, da orientação das camadas (0 e 90° e da pressão de moldagem (0 e 2 MPa sobre o comportamento à flexão dos laminados. Os resultados indicam que a adição de fibras de sisal aumentou, para todos os casos estudados, a capacidade de absorver energia, a resistência à flexão pós-fissuração e a deflexão última do material. Os laminados reforçados com 3% de fibras de sisal, distribuídas em três camadas ortogonais à direção do carregamento e submetidos à pressão de moldagem de 2 MPa, apresentaram o melhor comportamento mecânico.Because of hazards to human and animal health, the use of asbestos and its products is being prohibited all around the world and academic institutions and fibre cement producers have been engaged in intensive research to find asbestos-free cement products. The application of natural fibres such as sisal to replace asbestos fibres can bring economical and ecological benefits due to their availability, low cost, low consumption of energy and suitability to the semi-arid area of the Northeast of Brazil (where not many plants can grow. In this paper, cement-based laminates reinforced with continuous sisal fibre were produced. Three point bending tests were carried out to evaluate the influence of addition of fibre (3%, number of layers of

Efficacy of Thermally Conditioned Sisal FRP Composite on the Shear Characteristics of Reinforced Concrete Beams

OpenAIRE

Sen, Tara; Reddy, H. N. Jagannatha

2013-01-01

The development of commercially viable composites based on natural resources for a wide range of applications is on the rise. Efforts include new methods of production and the utilization of natural reinforcements to make biodegradable composites with lignocellulosic fibers, for various engineering applications. In this work, thermal conditioning of woven sisal fibre was carried out, followed by the development of woven sisal fibre reinforced polymer composite system, and its tensile and flex...

A influência do espaçamento sôbre o ciclo vegetativo do sisal

Directory of Open Access Journals (Sweden)

J. C. Medina

1946-01-01

Full Text Available The present paper deals with the influence of different rates of spacing on the poling of sisal plants (Agave sisalana Perrine. The results were obtained from spacing trials (four randomized blocks of nine treatments carried out at the Ribeirão Preto and Pindorama Experimental Stations. The percentages of poling plants, up to the 5th leaf cutting, were 20,0% and 91,7% for the narrowest (1,2 x 2,0 m and widest (2,0 x 3,0 m spacings tried in Pindorama, while in Ribeirão Preto they were 12,5% and 02,5%, respectivelly. According to these results it may be concluded that the narrow spaced plants were less liable to early poling than the wide spacing ones. The trial at Ribeirão Preto also indicated that among the plants, grown under the same conditions, those producing leaves at a faster rate were the first to pole. At that Station, the yearly average lenf production per plant (for all treatments up to the 4th leaf cutting, has been 41,5 leaves for those plants poling after 63 months ; 38,0 leaves for those poling after 74 months ; and 35,3 leaves for those plants not poled up to 5 th cutting.

Estudo da influência de tratamentos químicos da fibra de sisal nas propriedades de compósitos com borracha nitrílica Study of the influence from chemical treatments of sisal fibers on the properties of composites with nitrile rubber

Directory of Open Access Journals (Sweden)

Marco A. Iozzi

2010-01-01

Full Text Available A influência de diferentes tratamentos das fibras de sisal nas propriedades dos compósitos de borracha nitrílica/fibras de sisal, e borracha nitrílica/carbonato de cálcio/fibras de sisal foi investigada. Os compósitos, com fibras curtas aleatoriamente distribuídas, foram processados em moinho de dois rolos e caracterizados através de ensaios mecânicos de resistência à tração, microscopia eletrônica de varredura (MEV, análise por termogravimetria (TG e calorimetria exploratória diferencial (DSC. O tratamento de mercerização das fibras levou a uma maior adesão na interface fibra/matriz. O uso combinado de 67 pcr de carbonato com 33 pcr de fibras de sisal mercerizadas produziu um compósito com aumento significativo no módulo de elasticidade e sem perda da resistência à tração de ruptura. Os resultados da análise térmica mostraram que os compósitos são termicamente estáveis até cerca de 300 °C. Os materiais obtidos possuem uma boa relação custo/benefício tornando promissora sua utilização.In this work, composites were produced with nitrile rubber and sisal fibers, and nitrile rubber with calcium carbonate and sisal fibers. The composites were processed on a two-roll mixing mill and their properties were investigated with regard to the influence of chemical treatments of the fibers. The composites, with short fibers randomly distributed, were characterized by mechanical analysis, scanning electron microscopy (SEM, thermogravimetric analysis (TGA and differential scanning calorimetry (DSC. Mercerization treatment of the fibers promoted increasing the adhesion between the fiber and the rubber matrix. The composites of nitrile rubber with 67 pcr of calcium carbonate and 33 pcr of mercerized sisal fibers showed the best mechanical properties. Thermal analysis demonstrated that the composites are thermally stable up to 300 °C. The materials developed have a good cost/benefit relationship making their utilization

Mechanical Behaviour of Sisal Fibre Reinforced Cement Composites

OpenAIRE

M. Aruna

2014-01-01

Emphasis on the advancement of new materials and technology has been there for the past few decades. The global development towards using cheap and durable materials from renewable resources contributes to sustainable development. An experimental investigation of mechanical behaviour of sisal fibre-reinforced concrete is reported for making a suitable building material in terms of reinforcement. Fibre reinforced Composite is one such material, which has reformed the concept of high strength. ...

Interface Bond Improvement of Sisal Fibre Reinforced Polylactide Composites with Added Epoxy Oligomer.

Science.gov (United States)

Hao, Mingyang; Wu, Hongwu; Qiu, Feng; Wang, Xiwen

2018-03-07

To improve the interfacial bonding of sisal fiber-reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with addition of a commercial grade epoxy-functionalized oligomer Joncryl ADR @ -4368 (ADR). The FTIR (Fourier Transform infrared spectroscopy) analysis and SEM (scanning electron microscope) characterization demonstrated that the PLA molecular chain was bonded to the fiber surface and the epoxy-functionalized oligomer played a hinge-like role between the sisal fibers and the PLA matrix, which resulted in improved interfacial adhesion between the fibers and the PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of the ADR oligomer, which in turn reflected the improved interfacial interaction between SF and the PLA matrix. These results were further justified with the calculation of activation energies of glass transition relaxation (∆ E a ) by dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened with the addition of ADR oligomer. The interfacial interaction and structure-properties relationship of the composites are the key points of this study.

Impact of Surface Modification and Nanoparticle on Sisal Fiber Reinforced Polypropylene Nano composites

International Nuclear Information System (INIS)

Ibrahim, I. D.; Jamiru, T.; Sadiku, E. R.; Agwuncha, S. Ch.; Kupolati, W. K.

2016-01-01

The use of plant fibers, polymer, and nanoparticles for composite has gained global attention, especially in the packaging, automobile, aviation, building, and construction industries. Nano composites materials are currently in use as a replacement for traditional materials due to their superior properties, such as high strength-to-weight ratio, cost effectiveness, and environmental friendliness. Sisal fiber (SF) was treated with 5% NaOH for 2 hours at 70"°C. A mixed blend of sisal fiber and recycled polypropylene (rPP) was produced at four different fiber loadings: 10, 20, 30, and 40 wt.%, while nano clay was added at 1, 3, and 5 wt.%. Maleic anhydride grafted polypropylene (MAPP) was used as the compatibilizer for all composites prepared except the untreated sisal fibers. The characterization results showed that the fiber treatment, addition of MAPP, and nano clay improved the mechanical properties and thermal stability and reduced water absorption of the SF/rPP nano composites. The tensile strength, tensile modulus, and impact strength increased by 32.80, 37.62, and 5.48%, respectively, when compared to the untreated SF/rPP composites. Water absorption was reduced due to the treatment of fiber and the incorporation of MAPP and nano clay.

Comparison of thermal behavior of natural and hot-washed sisal fibers based on their main components: Cellulose, xylan and lignin. TG-FTIR analysis of volatile products

Energy Technology Data Exchange (ETDEWEB)

Benítez-Guerrero, Mónica, E-mail: monica_benitez_guerrero@yahoo.es [Departamento de Ingeniería Civil, Materiales y Fabricación, Universidad de Málaga, Escuela de Ingenierías, C/ Dr. Ortiz Ramos s/n, Campus Teatinos, 29071 Málaga (Spain); López-Beceiro, Jorge [Departamento de Ingeniería Industrial II, Escola Politécnica Superior, Universidade da Coruña, Avda. Mendizábal, 15403 Ferrol (Spain); Sánchez-Jiménez, Pedro E. [Instituto de Ciencia de Materiales de Sevilla, CSIC-Universidad de Sevilla, C/ Américo Vespucio 49, 41092 Sevilla (Spain); Pascual-Cosp, José [Departamento de Ingeniería Civil, Materiales y Fabricación, Universidad de Málaga, Escuela de Ingenierías, C/ Dr. Ortiz Ramos s/n, Campus Teatinos, 29071 Málaga (Spain)

2014-04-01

Highlights: • Thermal decomposition of sisal fibers has been discussed. • Decompositions of lignocellulosic components and sisal are compared by TXRD and TG-FTIR. • Hot washing reduces the temperature range in which sisal decomposition occurs. • Sisal cellulose decomposition goes by an alternative route to levoglucosan generation. - Abstract: This paper presents in a comprehensive way the thermal behavior of natural and hot-washed sisal fibers, based on the fundamental components of lignocellulosic materials: cellulose, xylan and lignin. The research highlights the influence exerted on the thermal stability of sisal fibers by other constituents such as non-cellulosic polysaccharides (NCP) and mineral matter. Thermal changes were investigated by thermal X-ray diffraction (TXRD), analyzing the crystallinity index (%Ic) of cellulosic samples, and by simultaneous thermogravimetric and differential thermal analysis coupled with Fourier-transformed infrared spectrometry (TG/DTA-FTIR), which allowed to examine the evolution of the main volatile compounds evolved during the degradation under inert and oxidizing atmospheres. The work demonstrates the potential of this technique to elucidate different steps during the thermal decomposition of sisal, providing extensible results to other lignocellulosic fibers, through the analysis of the evolution of CO{sub 2}, CO, H{sub 2}O, CH{sub 4}, acetic acid, formic acid, methanol, formaldehyde and 2-butanone, and comparing it with the volatile products from pyrolysis of the biomass components. The hydroxyacetaldehyde detected during pyrolysis of sisal is indicative of an alternative route to that of levoglucosan, generated during cellulose pyrolysis. Hot-washing at 75 °C mostly extracts non-cellulosic components of low decomposition temperature, and reduces the range of temperature in which sisal decomposition occurs, causing a retard in the pyrolysis stage and increasing Tb{sub NCP} and Tb{sub CEL}, temperatures at the

Viscoelastic and thermal properties of woven sisal fabric reinforced natural rubber biocomposites

CSIR Research Space (South Africa)

John, MJ

2009-01-01

Full Text Available This study explores the dynamic mechanical behavior of woven sisal fabric reinforced natural rubber composites. The influence of chemical modification on the viscoelastic properties has also been determined. Moreover, the effect of frequency...

Hemithoracic radiation therapy after pleurectomy/decortication for malignant pleural mesothelioma

International Nuclear Information System (INIS)

Gupta, Vishal; Mychalczak, Borys; Krug, Lee; Flores, Raja; Bains, Manjit; Rusch, Valerie W.; Rosenzweig, Kenneth E.

2005-01-01

Purpose: To evaluate pleurectomy/decortication (P/D) and adjuvant radiotherapy (RT) in the treatment of malignant pleural mesothelioma (MPM). Methods and Materials: In a retrospective review, we included MPM patients treated with P/D and adjuvant RT at Memorial Sloan-Kettering Cancer Center from 1974 to 2003. When indicated, patients received intraoperative brachytherapy to residual tumor. Results: All 123 patients received external beam RT (median dose, 42.5 Gy; range, 7.2-67.8 Gy) to the ipsilateral hemithorax postoperatively. Fifty-four patients underwent brachytherapy (matched peripheral dose, 160 Gy). The median and 2-year overall survival for all patients was 13.5 months (range, 1-199 months) and 23%, respectively. One-year actuarial local control for all patients was 42%. Multivariate analysis for overall survival revealed radiation dose <40 Gy (p = 0.001), nonepithelioid histology (p = 0.002), left-sided disease (p = 0.01), and the use of an implant (p = 0.02) to be unfavorable. Two patients (1.6%) died from Grade 5 toxicity within 1 month of treatment. Conclusions: Pleurectomy/decortication with adjuvant radiotherapy is not an effective treatment option for patients with MPM. Our results imply that residual disease cannot be eradicated with external RT with or without brachytherapy and that a more extensive surgery followed by external RT might be required to improve local control and overall survival

Estudo das propriedades de compósitos biodegradáveis de amido/glúten de milho/glicerol reforçados com fibras de sisal Study of properties of biodegradable composites of starch/gluten/glycerol reinforced with sisal fibers

Directory of Open Access Journals (Sweden)

Elisângela Corradini

2008-01-01

Full Text Available Neste estudo, fibras de sisal foram utilizadas como reforço para a matriz constituída de amido, glúten de milho e glicerol. O teor de fibra em relação a matriz variou de 5 a 30%. O processamento da matriz e dos compósitos foi realizado em um reômetro de torque Haake à 130 °C, 50 rpm por 10 minutos. As misturas obtidas foram moldadas por compressão à quente. As propriedades mecânicas; termodinâmico-mecânico (DMTA e de absorção de água foram investigadas em função do teor de fibras na matriz de amido/glúten de milho/glicerol. O aumento do conteúdo de fibra provocou uma melhoria nas propriedades mecânicas dos compósitos com relação à matriz. O compósito reforçado com 30% de fibra de sisal apresentou aumento no módulo de elasticidade e tensão na ruptura de aproximadamente de 560 e 162%, respectivamente e diminuição nos valores de elongação na ruptura de 81%. Os resultados obtidos por DMTA mostraram aumento progressivo do módulo de armazenamento (E' e diminuição do módulo de amortecimento (tan d com o aumento do teor de fibra, confirmando o efeito de reforço das fibras de sisal na matriz de amido/glúten de milho/glicerol. A incorporação das fibras na matriz também provocou diminuição da absorção de umidade e no coeficiente de difusão de água. A análise da morfologia dos compósitos mostrou boa dispersão das fibras na matriz.Biocomposites using starch/gluten/glycerol as matrix and sisal fibers were produced by melt-mixing in an intensive batch mixer connected to a torque rheometer at 130 °C. The samples were compression molded and than characterized by water absorption and mechanical test. In tensile test, the increasing in the Young's modulus and ultimate tensile strenght were respectively of aproximately 560 and 162% in relation to matrix, whereas elongation at break decreased. The storage modulus increased with increasing fiber content whereas tan d curves decreased, confirming the reinforcing

Methomyl poisoning presenting with decorticate posture and cortical blindness.

Science.gov (United States)

Lin, Chih-Ming

2014-01-17

Methomyl is a potent pesticide that is widely used in the field of agriculture. The systemic toxic effects of methomyl have been well described. However, the neurological effects of methomyl intoxication are not well understood. In this study, we report a 61-year-old Taiwanese man sent to our emergency department because of altered mental status. His family stated that he had consumed liquid methomyl in a suicide attempt. He was provided cardiopulmonary resuscitation because of unstable vital signs. He was then sent to an intensive care unit for close observation. On the second day of admission, he regained consciousness but exhibited irregular limb and torso posture. On the sixth day, he started to complain of blurred vision. An ophthalmologist was consulted but no obvious abnormalities could be identified. On suspicion of cerebral disease, a neurologist was consulted. Further examination revealed cortical blindness and decorticate posture. Cerebral magnetic resonance imaging (MRI) was arranged, which identified bilateral occipital regions lesions. The patient was administered normal saline and treated with aspirin and piracetam for 3 weeks in hospital. During the treatment period, his symptom of cortical blindness resolved, whereas his decorticate posture was refractory. Follow-up brain MRI results supported our clinical observations by indicating the disappearance of the bilateral occipital lesions and symmetrical putaminal high signal abnormalities. In this article, we briefly discuss the possible mechanisms underlying the cerebral effects of methomyl poisoning. Our study can provide clinicians with information on the manifestations of methomyl intoxication and an appropriate treatment direction.

Methomyl poisoning presenting with decorticate posture and cortical blindness

Directory of Open Access Journals (Sweden)

Chih-Ming Lin

2014-02-01

Full Text Available Methomyl is a potent pesticide that is widely used in the field of agriculture. The systemic toxic effects of methomyl have been well described. However, the neurological effects of methomyl intoxication are not well understood. In this study, we report a 61-year-old Taiwanese man sent to our emergency department because of altered mental status. His family stated that he had consumed liquid methomyl in a suicide attempt. He was provided cardiopulmonary resuscitation because of unstable vital signs. He was then sent to an intensive care unit for close observation. On the second day of admission, he regained consciousness but exhibited irregular limb and torso posture. On the sixth day, he started to complain of blurred vision. An ophthalmologist was consulted but no obvious abnormalities could be identified. On suspicion of cerebral disease, a neurologist was consulted. Further examination revealed cortical blindness and decorticate posture. Cerebral magnetic resonance imaging (MRI was arranged, which identified bilateral occipital regions lesions. The patient was administered normal saline and treated with aspirin and piracetam for 3 weeks in hospital. During the treatment period, his symptom of cortical blindness resolved, whereas his decorticate posture was refractory. Follow-up brain MRI results supported our clinical observations by indicating the disappearance of the bilateral occipital lesions and symmetrical putaminal high signal abnormalities. In this article, we briefly discuss the possible mechanisms underlying the cerebral effects of methomyl poisoning. Our study can provide clinicians with information on the manifestations of methomyl intoxication and an appropriate treatment direction.

Effect of incorporation of decorticated pigeon pea (Cajanus cajan) protein isolate on functional, baking and sensory characteristics of Wheat (Triticum aesitivum) biscuit

OpenAIRE

H. A. Hassan; A.I. Mustafa; A.R. Ahmed

2013-01-01

This study was undertaken with the objectives of using the decorticated pigeon pea protein isolate in the development of protein rich-biscuit, suitable for general and specific nutritional purposes and to study the effect of incorporation of pigeon pea protein isolate on the sensory evaluation and quality of biscuit produced. Decorticated Pigeon Pea protein Isolate (DPPI) was incorporated in wheat (Triticum aesitivum) flour (WF, extraction rate 72%), for making fortified biscuit. Ratios of DP...

Morphology and crystallinity of sisal nanocellulose after sonication

Science.gov (United States)

Sosiati, H.; Wijayanti, D. A.; Triyana, K.; Kamiel, B.

2017-09-01

Different preparation methods on the natural fibers resulted in different morphology. However, the relationships between type of natural fibers, preparation methods and the morphology of produced nanocellulose could not be exactly defined. The sisal nanocellulose was presently prepared by alkalization and bleaching followed by sonication to verify changes in the morphology and crystallinity of nanocellulose related to the formation mechanism. The extracted microcellulose was subjected to scanning electron microscopy (SEM) and x-ray diffraction (XRD) analysis. The isolated cellulose nanospheres were examined with respect to morphology by SEM and transmission electron microscopy (TEM) and, to crystallinity by electron diffraction analysis. Bleaching after alkalization made the microfibrils clearly separated from each other to the individual fiber whose width of the single fiber was ranging from 6 to 13 µm. The XRD crystallinity index (CI) of microcellulose gradually increased after the chemical treatments; 83.12% for raw sisal fiber, 88.57% for alkali treated fiber and 94.03% for bleached fibers. The ultrasonic agitation after bleaching that was carried out at 750 Watt, 20 kHz and amplitude of 39% for 2 h produces homogeneous cellulose nanospheres less than 50 nm in diameter with relatively low crystallinity. The electron diffraction analysis confirmed that the low crystallinity of produced nnocellulose is related to the effect of chemical treatment done before sonication.

DESENVOLVIMENTO DE TECIDOS DE SISAL PARA UTILIZAÇÃO EM COMPÓSITOS POLIMÉRICOS

Directory of Open Access Journals (Sweden)

Camila Cruz da Silva

2010-01-01

Full Text Available A utilização das fibras naturais (lignocelulosicas como reforço, em materiais compósitos polimérico, é algo que vem crescendo significativamente dia, após dia. Devido ao fato desses materiais serem biodegradáveis, provém de fontes renováveis, desenvolvendo assim as regiões onde são extraídas possibilitando dessa forma a permanência do homem no campo, fazendo parte assim de um modelo ecologicamente correto. Dentre essas fibras dá um destaque a fibra de sisal,onde esta está sendo bastante estudada e utilizada na indústria automobilística. A fibra é extraída da folha do agave sisalina, e que foi introduzida no Brasil em meados de 1900, tendo como maiores produtores os estados da Bahia, Paraíba e Rio Grande do Norte. O objetivo deste trabalho é o desenvolvimento de dois tecidos de sisal para a utilização em materiais compósitos poliméricos, já que estes não são encontrados na indústria. Dessa forma foram fabricados dois tecidos sendo um do tipo plano e o outro do tipo plano basket, onde estes foram obtidos em teares manuais. PALAVRAS-CHAVE: Materiais Compósitos, Sisal e Tecidos.

Utilização de pós residuais e fibra de sisal em blocos de concreto

OpenAIRE

Indara Soto Izquierdo

2015-01-01

A pesquisa tem como enfoque fundamental a aplicação de novos materiais alternativos para uma construção sustentável. Pós residuais, provenientes do resíduo orgânico e do setor mineral, e fibras de sisal constituem bons exemplos de materiais não convencionais. Dessa forma, o objetivo principal foi avaliar a incorporação dos pós residuais e da fibra de sisal no concreto para a fabricação de blocos de concreto e elementos de alvenaria. Foram estudados três relações cimento: agregado, de 1:15, 1:...

Tendências tecnológicas do uso do sisal em compósitos a partir da prospecção em documentos de patentes

Directory of Open Access Journals (Sweden)

Felipe Scopel

2013-01-01

Full Text Available As fibras naturais têm sido pesquisadas e empregadas de maneira crescente no desenvolvimento de produtos com sustentabilidade econômica, social e ambiental, sendo o sisal uma das mais importantes para o Brasil, pela sua posição de liderança na produção mundial. O presente artigo analisa a evolução temporal e o interesse das empresas e instituições em tecnologias associadas ao sisal, a partir de informações e indicadores extraídos de documentos de patentes no período de 1960 a 2009. Foi verificado o crescente patenteamento associado ao sisal em áreas de química, ciência dos materiais e dos polímeros, com destaque para o reforço do de compósitos plásticos. Além do crescente número de patentes, houve também um expressivo aumento do número de empresas e instituições titulares das patentes, o que reflete a possível desconcentração do mercado nesse crescimento do interesse pelas tecnologias associadas ao sisal. O Brasil, apesar da sua proeminência na produção do sisal, possui pequena presença no patenteamento mundial. Também foi verificada a importância da análise de patentes para o acompanhamento da evolução das tecnologias e interesses, pela disponibilidade de informações públicas que podem ser transformadas em indicadores úteis para análise de tecnologia e mercado associados ao sisal ou a outras áreas tecnológicas.

Obtaining nanofibers from sisal to reinforce nanocomposites biodegradable matrixes

International Nuclear Information System (INIS)

Oliveira, Francieli B. de; Teixeira, Eliangela de M.; Marconcini, Jose M.; Mattoso, Luiz H.C.; Teodoro, Kelcilene B.R.

2009-01-01

Cellulose nanofibers have been extracted by acid hydrolysis from sisal fibers. They are seen a good source material due to availability and low cost. The nanofibers was evaluated by thermal degradation behavior using thermogravimetry (TG), crystallinity by X-ray diffraction and morphological structure was investigated by atomic force microscopy (AFM) experiments. The resulting nanofibers was shown high crystallinity and a network of rodlike cellulose elements. The nanofibers will be incorporated as reinforcement in a biodegradable matrix and evaluated. (author)

Feasibility of a simple drainage system in Cameroonian children after thoracotomy and decortication for empyema thoracis

Directory of Open Access Journals (Sweden)

Bernadette Ngo Nonga

2012-01-01

Full Text Available Background: To analyse the outcome of children with empyema thoracis treated by decortication followed by a simple drainage system. Patients and Methods: Retrospective chart review from July 2001 to June 2010 of all cases of children who had a thoracotomy for empyema. We used an endotracheal tube as chest drain and a urinary bag as a collector. Statistical analyses were done using EXCEL and SPSS 9.0. Results: Forty one children underwent thoracotomy and decortication for empyema, there were 23 boys and 18 girls with a sex ratio of 1, 21. The mean age was 2½ years with a minimum of 1 month and a maximum of 15 years of age; 27 children were below two years of age. All the patients have received antibiotic for a long period before surgery. The culture was negative, except in two cases where we found Klebsiella pneumonia and Staphylococcus aureus. In five cases, the empyema was due to Mycobacterium tuberculosis. Three children presented a complication: One child had a persistent purulent drainage for 2 weeks; another one was re-operated upon because of necrotic lung abscess and one child died of sepsis. In most cases, the chest tube was removed between day 4 and day 6 post-operatively. The average length of hospital stay after the surgery was 10 days. Conclusion: Thoracotomy and decortication in children with empyema can be safely done in Cameroon using a simple drainage system with good results compared to those in the literature.

The design of financial recording system in industrial bio-briquette of Ramie (Boehmeria nivea) decortication waste with design thinking approach

Science.gov (United States)

Irianto, R.; Purnomo, D.; Prima, S.; Wulandari, A.

2017-05-01

The production process of ramie (boehmeria nivea) fibers generates waste which contents 5.95 to 7.83% ash; 1.88 to 2.87% silicate; 30.67 to 31.08% lignin; 33.81 to 35.99% alpha cellulose; 62.95 to 63.78% holoselulosa; 17.43 to 18.14% pentosan, which can be used as raw material of bio-briquette. Those potential can be used to generate a business opportunity, such as industrial bio-briquette of ramie decortication waste. The purpose of this research is to create accounting information which could present an income statement that is easily applied on industrial bio-briquette of ramie decortication waste. This research use descriptive analysis method with design with design thinking approach to gather the information through depth observation on human being as the object to achieve the purpose. The result in this research is financial recording system of industrial bio-briquette of ramie decortication waste in a desktop application. The system is integrated with production activities according to the needs of accounting information particularly at managerial production. The existing applications creates information in the form of financial operations which can be used as a factor in decision-making.

DESINFESTAÇÃO DE REBENTOS DE SISAL PARA UTILIZAÇÃO IN VITRO

Directory of Open Access Journals (Sweden)

Flavia Monique Sales Nobrega

2015-08-01

Full Text Available Em todo o mundo, o sisal (Agave sisalana é conhecido pelo alto teor de suas fibras, amplamente utilizadas na fabricação de utensílios, na indústria automotiva, na indústria química e na construção cívil. No entanto, alguns fatores podem inviabilizar o desenvolvimento da cultura, a exemplo de doenças, como a podridão do colo, causada por fungos do gênero Pythium sp. Visando à obtenção de mudas sadias e livres de patógenos buscou-se, com este trabalho, definir um protocolo eficiente para a desinfestação de rebentos de sisal, utilizando-se diferentes concentrações e diversas combinações do antibiótico Citrofloxacino e do Fungicida Baytan®. Os explantes foram desinfestados em soluções com detergente neutro, hipoclorito de sódio e formaldeído e, em seguida, submetidos a soluções com diferentes concentrações do antibiótico e do fungicida combinados e só então cultivados em meio MS. Foram realizadas avaliações aos 7, 15 e 21 dias, após o cultivo, para análise da taxa de contaminação bacteriana e fúngica. Observou-se, portanto, que a utilização de 0,5% do fungicida Baytan®, associado a 1% do antibiótico Citrofloxacino, foi mais eficiente na descontaminação de explantes de sisal.

Construction and evaluation of normalized cDNA libraries enriched with full-length sequences for rapid discovery of new genes from Sisal (Agave sisalana Perr.) different developmental stages.

Science.gov (United States)

Zhou, Wen-Zhao; Zhang, Yan-Mei; Lu, Jun-Ying; Li, Jun-Feng

2012-10-12

To provide a resource of sisal-specific expressed sequence data and facilitate this powerful approach in new gene research, the preparation of normalized cDNA libraries enriched with full-length sequences is necessary. Four libraries were produced with RNA pooled from Agave sisalana multiple tissues to increase efficiency of normalization and maximize the number of independent genes by SMART™ method and the duplex-specific nuclease (DSN). This procedure kept the proportion of full-length cDNAs in the subtracted/normalized libraries and dramatically enhanced the discovery of new genes. Sequencing of 3875 cDNA clones of libraries revealed 3320 unigenes with an average insert length about 1.2 kb, indicating that the non-redundancy of libraries was about 85.7%. These unigene functions were predicted by comparing their sequences to functional domain databases and extensively annotated with Gene Ontology (GO) terms. Comparative analysis of sisal unigenes and other plant genomes revealed that four putative MADS-box genes and knotted-like homeobox (knox) gene were obtained from a total of 1162 full-length transcripts. Furthermore, real-time PCR showed that the characteristics of their transcripts mainly depended on the tight expression regulation of a number of genes during the leaf and flower development. Analysis of individual library sequence data indicated that the pooled-tissue approach was highly effective in discovering new genes and preparing libraries for efficient deep sequencing.

UTILIZATION OF MICRO SISAL FIBERS AS REINFORCEMENT AGENT AND POLYPROPYLENE OR POLYLACTIC ACID AS POLYMER MATRICES IN BIOCOMPOSITES MANUFACTURE

Directory of Open Access Journals (Sweden)

Subyakto Subyakto

2013-06-01

Full Text Available Sisal (Agave sisalana as a perennial tropical plant grows abundantly in Indonesia. Its fibers can be used as the reinforcement agent of biocomposite products. Utilization of sisal as natural fiber has some notable benefits compared to synthetic fibers, such as renewable, light in weight, and low in cost. Manufacture of biocomposite requires the use of matrix such as thermoplastic polymer, e.g. polypropylene (PP and polylactic acid (PLA to bond together with the reinforcement agent (e.g. sisal fibers. In relevant, experiment was conducted on biocomposites manufacture that comprised sisal fibers and PP as well as PLA. Sisal fibers were converted into pulp, then refined to micro-size fibrillated fibers such that their diameter reduced to about 10 μm, and dried in an oven. The dry microfibrillated sisal pulp fibers cellulose (MSFC were thoroughly mixed with either PP or PLA with varying ratios of MSFC/PP as well as MSFC/PLA, and then shaped into the mat (i.e. MSFC-PP and MSFC-PLA biocomposites. Two kinds of shaping was employed, i.e. hot-press molding and injection molding. In the hot-press molding, the ratio of  MSFC/PP as well as MSFC/PLA ranged about 30/70-50/50. Meanwhile in the injection (employed only on assembling the MSFC-PLA biocomposite, the ratio of MSFC/PLA varied about 10/90-30/70. The resulting shaped MSFC-PP and MSFC-PLA biocomposites were then tested of its physical and mechanical properties. With the hot-press molding device, the physical and mechanical (strength properties of MSFC-PLA biocomposite were higher than those of  MSFC-PP biocomposite. The optimum ratio of  MSFC/PP as well as MSFC/PLA reached concurrently at 40/60. The strengths of MSFC-PP as well as MSFC-PLA biocomposites were greater than those of individual polymer (PP and PLA. With the injection molding device, only the MSFC-PLA  biocomposite  was formed  and its strengths  reached  maximum  at 30/70  ratio.  The particular strengths (MOR and MOE of MSFC

Cellulose whiskers from sisal fibers: a study about the variable of extraction by acid hydrolysis

International Nuclear Information System (INIS)

Teodoro, Kelcilene B.R.; Teixeira, Eliangela de Morais; Correa, Ana Carolina; Campos, Adriana de; Marconcini, Jose Manoel; Mattoso, Luiz Henrique Capparelli

2011-01-01

The incorporation of cellulosic nanostructures in polymeric matrices has been studied due to their properties of biodegradation, and expected higher mechanical performance than the traditional composites. In this work, cellulose nanofibers were obtained from sisal bleached with reagents without chlorine, where it was used an acid mixture, with acetic acid and nitric acid, and after the bleached fibers were submitted to acid hydrolysis. The influence of the temperature and time of hydrolysis on the morphology and dimensions, crystallinity and thermal stability were analyzed by scanning transmission electronic microscopy (TEM), x-ray diffraction (XRD) and thermogravimetric analysis (TGA), respectively. The hydrolysis condition of 60 deg C and 15 minutes showed to be the most effective condition to obtain whiskers from sisal fibers, resulting in nanostructures with higher crystallinity and thermal. (author)

Thermal performance of sisal fiber-cement roofing tiles for rural constructions

OpenAIRE

Tonoli,Gustavo Henrique Denzin; Santos,Sérgio Francisco dos; Rabi,José Antonio; Santos,Wilson Nunes dos; Savastano Junior,Holmer

2011-01-01

Roofing provides the main protection against direct solar radiation in animal housing. Appropriate thermal properties of roofing materials tend to improve the thermal comfort in the inner ambient. Nonasbestos fiber-cement roofing components reinforced with cellulose pulp from sisal (Agave sisalana) were produced by slurry and dewatering techniques, with an optional addition of polypropylene fibers. Nonasbestos tiles were evaluated and compared with commercially available asbestos-cement sheet...

hybrid effect on the mechanical properties of sisal fiber and e-glass

African Journals Online (AJOL)

cles was added and the “mix” was vigorously stirred and poured into a mould. Appropriate quantities of fibers (sisal or E-glass) were im- pregnated in the “resin mix” which ultimately cured to give a solid laminate. 2.3. Tensile test. Standard tensile specimens were cut from the hybrid and non-hybrid composite lami-. Nigerian ...

Screening life cycle assessment study of a sisal fibre reinforced micro-concrete structural insulated panel

CSIR Research Space (South Africa)

Ampofo-Anti, N

2013-12-01

Full Text Available First international conference on composites, biocomposites and nanocomposites, DUT, Durban, South Africa, 2-4 December 2013 SCREENING LIFE CYCLE ASSESSMENT STUDY OFA SISAL FIBRE REINFORCED MICRO-CONCRETE STRUCTURAL INSULATED PANEL Naa Lamkai Ampofo...

Herbicidas no transplante de mudas de sisal (Agave sisalana perr. Weed control and herbicide selectivity to sisal (Agave sisalana perr.

Directory of Open Access Journals (Sweden)

Antonio Luiz de Barros Salgado

1980-01-01

Full Text Available Com o objetivo de verificar a eficiência de hebraicas no controle de plantas daninhas e sua seletividade à cultura do sisal, foi instalado, em setembro de 1976, um experimento de campo em solo argiloso, com os seguintes tratamentos (i.a./hectare trifluralin a 0,84 e 0,96kg em pré-plantio com incorporação; alachlor a 2,40 e 3,26kg; metribuzin a 0,70 e 0,84kg; bromacil a 1,60 e 2,40kg; terbacil a 1,60 e 2,40kg; diuron a 2,40 e 3,20kg; simazine a 3,20 e 4,00kg; fluometuron a 1,20 e 1,60kg, todos em pré-emergência; uma testemunha carpida e outra sem capina. Foram feitas avaliações de controle do mato aos 67 e 114 dias e da condição da cultura aos 600 dias após a aplicação. Aos 114 dias, o controle de gramíneas foi acima de 90% pelo trifluralin, bromacil e terbacil, em torno de 80% pelo simazine, e inferior a 75% pelos demais; para dícotiledôneas, o controle foi de 90 a 100% pelo bromacil e terbacil, e de 80 a 85%o pelo simazine. Nenhum dos tratamentos afetou a cultura durante o período considerado, que foi de 600 dias. Aos 550 dias, fez-se avaliação da área coberta por reinfestação do mato, tendo o terbacil controlado ainda 75 e 95% do total, respectivamente, para as doses menor e maior; o trifluralin, 60 e 70% e, os demais, abaixo de 45%. Na avaliação final da cultura, aos 600 dias, foram considerados: população de plantas, número de plantas com perfilhos e condição da cultura. Os tratamentos que realizaram melhor controle do mato apresentaram também os melhores índices de desenvolvimento da cultura, atestando sua seletividade.The weed control with herbicides and its selectivity to sisal were studied on a clay soil field trial. The treatments (in a.i./ha were: 0.84 and 0.96kg of pre-plant incorporated trifluralin; 2.40 and 3.26kg of alachlor; 0.70 and 0.84kg of metribuzin; 1.60 and 2.40kg of bromacil; 1.60 and 2.40kg of terbacil; 2.40 and 3.20k- of diuron; 3.20 and 4.00kg of simazine; 1.20 and 1.60kg of fluometuron

The applications of sisal fibre-based materials in the built environment: opportunities for South Africa

CSIR Research Space (South Africa)

Dlungwana, Sihle

2017-12-01

Full Text Available of sisal fibre-based materials in the built environment: opportunities for South Africa Sihle Dlungwana, Joe Mapiravana, Naa Lamkai Ampofo-Anti and Nozonke Dumani Introduction: The building sector represented the largest uptake globally of natural fibre...

Acid hydrolysis of sisal cellulose: studies aiming at nano fibers and bio ethanol preparation

International Nuclear Information System (INIS)

Paula, Mauricio P. de; Lacerda, Talita M.; Zambon, Marcia D.; Frollini, Elisabete

2009-01-01

The hydrolysis of cellulose can result in nanofibers and also is an important stage in the bioethanol production process. In order to evaluate the influence of acid (sulfuric) concentration, temperature, and native cellulose (sisal) pretreatment on cellulose hydrolysis, the acid concentration was varied between 5% and 30% (v/v) in the temperature range from 60 to 100 deg C using native and alkali-treated (mercerized) sisal cellulose. The following techniques were used to evaluate the residual (non-hydrolysed) cellulose characteristics: viscometry, average degree of polymerization (DP), X-ray diffraction, crystallinity index, and Scanning Electron Microscopy. The sugar cane liquor was analyzed in terms of sugar composition, using High Performance Liquid Chromatography (HPLC). The results showed that increasing the concentration of sulfuric acid and temperature afforded residual cellulose with lower molecular weight and, up to specific acid concentrations, higher crystallinity indexes, when compared to the original cellulose values, and increased the glucose (the bioethanol precursor ) production of the liquor, which was favored for mercerized cellulose. (author)

Enzymatic grafting of simple phenols on flax and sisal pulp fibres using laccases.

Science.gov (United States)

Aracri, Elisabetta; Fillat, Amanda; Colom, José F; Gutiérrez, Ana; Del Río, José C; Martínez, Angel T; Vidal, Teresa

2010-11-01

Flax and sisal pulps were treated with two laccases (from Pycnoporus cinnabarinus, PcL and Trametes villosa, TvL, respectively), in the presence of different phenolic compounds (syringaldehyde, acetosyringone and p-coumaric acid in the case of flax pulp, and coniferaldehyde, sinapaldehyde, ferulic acid and sinapic acid in the case of sisal pulp). In most cases the enzymatic treatments resulted in increased kappa number of pulps suggesting the incorporation of the phenols into fibres. The covalent binding of these compounds to fibres was evidenced by the analysis of the treated pulps, after acetone extraction, by pyrolysis coupled with gas chromatography/mass spectrometry in the absence and/or in the presence of tetramethylammonium hydroxide (TMAH) as methylating agent. The highest extents of phenol incorporation were observed with the p-hydroxycinnamic acids, p-coumaric and ferulic acids. The present work shows for the first time the use of analytical pyrolysis as an effective approach to study fibre functionalization by laccase-induced grafting of phenols. Copyright 2010 Elsevier Ltd. All rights reserved.

Estudo dos efeitos da acetilação em fibras de sisal Study of the effects of acetylation treatments on sisal fiber

Directory of Open Access Journals (Sweden)

Fernanda F. M. Lopes

2010-07-01

Full Text Available O emprego de fibras vegetais na confecção de compósitos tem grande viabilidade, no que diz respeito ao uso de materiais oriundos de fontes renováveis, à biodegradabilidade e aos benefícios socioeconômicos gerados na produção de matéria-prima vegetal. As fibras de sisal são altamente higroscópicas e esta característica se apresenta como um dos principais problemas na produção de compósitos induzindo a variações dimensionais sob a influência da umidade, deposição dos produtos da matriz em seus poros e a degradação. Os tratamentos de acetilação nas fibras de sisal foram aplicados em diferentes temperaturas e tempos reacionais, e a eficiência desses tratamentos, considerando-se a redução da hidrofilicidade e a manutenção do desempenho mecânico das fibras, foi avaliada pela capacidade de absorção de água por imersão, ensaios de resistência mecânica e por espectroscopia de infravermelho. Fibras acetiladas apresentaram reduções de peso por absorção de até 50% quando comparadas com as não tratadas. Os tratamentos por 3 h apresentaram as maiores perdas na resistência mecânica e a 120 °C por 1h indicaram as melhores características físico-mecânicas, além de incremento satisfatório de grupos apolares com o tratamento.The use of vegetable fibers in composites is highly viable regarding about the use of materials from renewable sources, the biodegradability and the socioeconomic advantages in the production of raw vegetable. The sisal fibers are highly hygroscopic and this is a main problem in the production of composites, inducing dimensional changes under moisture influence, deposition of the matrix products and degradation. The treatment of the acetylation was applied at different temperatures and reaction times, and the efficiency of treatments, considering the reduction of the hydrophilicity and maintenance of the mechanical properties, was evaluated by water sorption, mechanical properties and the

Inclusão de feixes de sisal na produção de painéis MDP de eucalipto

DEFF Research Database (Denmark)

de Almeida Mesquita, Ricardo G; Mendes, Lourival Marin; Mendes, Rafael Farinassi

2015-01-01

of the plastic industry. This lignocellulose material has gained prominence due to several mechanical and economic characteristics. Thus, the aim of this study was to evaluate the potential use of sisal bundles in association with eucalyptus particles for the production of MDP panels. Panels were prepared...... with the substitution on eucalyptus wood for sisal bundles in the panels’ core in doses of 0, 5, 10, 15, 20 and 25%. The MDP panels were produced with face/core 40/60 (base dry mass of the particles), urea-formaldehyde adhesive, nominal density of 0,70 g.cm-3 and pressing cycle of 8 minutes, 3,92 MPa pressure...

Influência da decorticação vertebral na neoformação dos tecidos da interface do enxerto ósseo Influence of vertebral decortication on tissue neoformation at bone graft interface

Directory of Open Access Journals (Sweden)

Fabiano Ricardo Tavares Canto

2010-01-01

Full Text Available OBJETIVO: Determinar a influência da decorticação dos elementos posteriores da coluna vertebral na integração do enxerto ósseo, considerando a avaliação quantitativa e qualitativa dos tecidos (ósseo, cartilaginoso e fibroso da interface entre o leito receptor e o enxerto ósseo. MÉTODOS: Foram utilizados 24 ratos Wistar, divididos em dois grupos de acordo com a realização da decorticação do leito receptor do enxerto. Foi utilizado enxerto autólogo derivado dos processos espinhosos das duas primeiras vértebras lombares. A neoformação tecidual na interface entre o leito receptor e seu enxerto ósseo foi avaliada após três semanas por meio de análise histomorfométrica. RESULTADOS: No grupo de animais com o leito receptor decorticado a média da porcentagem de osso neoformado foi de 40%±6,1, e 7,7%± 3,5 no grupo não decorticado (p=0,0001. A média da porcentagem de formação do tecido cartilaginoso no grupo decorticado foi de 7,2%±3,5, no não decorticado de 10,9%±5,6 (p=0,1123. A formação de tecido fibroso no grupo decorticado apresentou média de 8,6%±3,9 e no não decorticado e 24%±10,1, (p=0,0002. CONCLUSÕES: A decorticação acelerou o processo histológico da integração do enxerto ósseo. Ocorrendo maior produção de tecido ósseo neoformado e predomínio da ossificação do tipo intramembranosa no grupo de animais nos quais a decorticação foi realizada.OBJECTIVE: To determine the influence of vertebral posterior elements decortication in bone graft integration, considering a qualitative and quantitative evaluation of the (bone, cartilaginous, and fibrous tissues in the interface between the receptor bed and the bone graft. METHODS: Twenty-four Wistar rats were divided into two groups according to the decortication of the bone graft receptor bed. Autologous bone graft from the first and second lumbar vertebrae were used. The new tissue formation in the interface between the receptor bed and its bone graft

Application of foam column as green technology for concentration of saponins from sisal (Agave sisalana and Juá (Ziziphus joazeiro

Directory of Open Access Journals (Sweden)

B. D. Ribeiro

2013-12-01

Full Text Available Saponins, molecules classified as triterpenic or steroidal glycosides, are metabolites distributed in all the plant kingdom that can be used for the production of foods, cosmetics, and pharmaceuticals, as well as in soil bioremediation. Saponins are normally extracted from natural resources with water, ethanol and/or methanol, and then concentrated by liquid-liquid partitioning with n-butanol. An alternative concentration method is with a foam column, by which the saponins can be concentrated via preferential adsorption at a gas-liquid interface. Therefore, the objective of this work was the use of a foam column for the concentration of saponins from juá and sisal, evaluating parameters such as: initial working volume in the column, saponin concentration in the extracts from juá and sisal, air flow rate, pH, Raschig rings loading and operation time. When a gradient air flow rate and 25 g of Raschig rings were used, 82.6% of the jua saponins loaded onto the system were recovered in a 3.46-fold concentrated solution after 9 h of operation. Regarding sisal saponins, a concentration factor of 1.98 was observed with 90.5% of saponin recovery during 4.5 h of operation.

Effect of Coconut, Sisal and Jute Fibers on the Properties of Starch/Gluten/Glycerol Matrix

Science.gov (United States)

Coconut, sisal and jute fibers were added as reinforcement materials in a biodegradable polymer matrix comprised of starch/gluten/glycerol. The content of fibers used in the composites varied from 5% to 30% by weight of the total polymers (starch and gluten). Materials were processed in a Haake torq...

Consumo e desempenho produtivo de ovinos alimentados com dietas que continham coprodutos do desfibramento do sisal

Directory of Open Access Journals (Sweden)

R.D. Santos

2011-12-01

Full Text Available Avaliaram-se o desempenho produtivo e o consumo de nutrientes e frações fibrosas em ovinos alimentados com dietas contendo coprodutos do desfibramento do sisal, Agave sisalana. Foram utilizados 24 ovinos, machos, alojados em baias individuais. O delineamento experimental utilizado foi o inteiramente ao acaso, com quatro tratamentos e seis repetições. Os tratamentos consistiram em quatro dietas isoproteicas, em que: i dieta padrão, contendo 38% de volumoso (silagem de milheto e 62% de concentrado (milho, farelo de soja e ureia; ii inclusão de 20% da silagem de mucilagem do sisal em substituição à silagem de milheto; iii inclusão de 20% da silagem de mucilagem associada ao pó da batedeira como aditivo em substituição à silagem de milheto; iv inclusão de 20% do feno da mucilagem em substituição à silagem de milheto. O peso corporal final, os ganhos médio diário e total e a conversão alimentar dos ovinos não foram influenciados pelas dietas avaliadas (P>0,05. Os consumos dos nutrientes, em g/dia e em %PC e g/kg0,75, não sofreram influência das dietas. Os resultados indicam que as dietas à base de coprodutos do sisal podem ser utilizadas como alternativa volumosa, além de possibilitar o aumento da rentabilidade da atividade na região semiárida brasileira.

Sisal, caso paradigmático de estudio: Prácticas de vida y basura

OpenAIRE

Ulsía Urrea Mariño

2016-01-01

Estudio del puerto de Sisal, Yucatán, México, sobre las prácticas de vida cotidiana ligadas a la basura, residuos y desechos en tres espacios de análisis (casa, vecindario y lugares de trabajo) y su relación con la economía subterránea, construcción de vivienda y pesca.

Chemicals from Agave sisalana Biomass: Isolation and Identification

Science.gov (United States)

Santos, Jener David Gonçalves; Vieira, Ivo Jose Curcino; Braz-Filho, Raimundo; Branco, Alexsandro

2015-01-01

Agave sisalana (sisal) is known worldwide as a source of hard fibers, and Brazil is the largest producer of sisal. Nonetheless, the process of removing the fibers of the sisal leaf generates 95% waste. In this study, we applied chemical sequential steps (hydrothermal extraction, precipitation, liquid-liquid extraction, crystallization, SiO2 and Sephadex LH 20 column chromatography) to obtain pectin, mannitol, succinic acid, kaempferol and a mixture of saponins as raw chemicals from sisal biomass. The structural identification of these compounds was performed though spectrometric methods, such as Infrared (IR), Ultraviolet (UV), Mass spectrometry (MS) and Nuclear magnetic resonance (NMR). All the sisal chemicals found in this work are used by both the chemical and pharmaceutical industries as excipients or active principles in products. PMID:25903149

Laparoscopic decortication of symptomatic renal cysts. Experience from a referral center in Iran

International Nuclear Information System (INIS)

Abbaszadeh, S.; Taheri, S.; Nourbala, M.H.

2008-01-01

The objective of this study was to present our experience with laparoscopic management of symptomatic simple renal cysts. From April 2004 to November 2006, 21 patients (10 men; 11 women) underwent laparoscopic decortication for simple renal cysts at our department and were included in the analysis. All procedures were carried out by one surgeon using a transperitoneal approach. Patients underwent radiological follow-up with computerized tomography and/or ultrasonography. Procedural success was defined as no recurrence of the cyst and complete pain relief. Symptomatic success was defined as a significant pain decrease. All 21 procedures were completed laparoscopically, without major complications or conversion to open surgery. Estimated mean blood loss during surgery was about 50 mL. Patients were hospitalized for a mean of 1.9±1.1 (range: 1-5) days. Age of the patients and size and location of the cysts, had no relationship with the duration of operation as well as the length of hospital stay (P>0.05). Patients who experienced complete pain relief had significantly larger cyst sizes compared with patients with a partial pain decrease (7.3±1.1 vs 9.1±2.0, respectively; P=0.023, F=0.606). All patients had negative cytological and pathological findings for malignancy or any other abnormalities. At 16.6 months of mean follow up, none of the patients reported symptomatic and/or radiologic failure. Laparoscopic transperitoneal decortication represents an effective and safe treatment option in the management of symptomatic renal cysts. (author)

Sisal, caso paradigmático de estudio: Prácticas de vida y basura

Directory of Open Access Journals (Sweden)

Ulsía Urrea Mariño

2016-06-01

Full Text Available Estudio del puerto de Sisal, Yucatán, México, sobre las prácticas de vida cotidiana ligadas a la basura, residuos y desechos en tres espacios de análisis (casa, vecindario y lugares de trabajo y su relación con la economía subterránea, construcción de vivienda y pesca.

Environmental constraints on motor abilities used in grooming, swimming, and eating by decorticate rats.

Science.gov (United States)

Whishaw, I Q; Nonneman, A J; Kolb, B

1981-10-01

In a number of successive tests, grooming, swimming, and eating behaviors of decorticate rats were reexamined by evoking the behaviors in various circumstances (stimulus conditions). The rats showed normal-length grooming sequences during spontaneous home cage grooming; when grooming was elicited by removing the rats from their home cage and soaking their fur by a brief swim, grooming-sequence length was abbreviated. In cold (18 degrees C) water, they swam well and with exaggerated vigor and frequently inhibited forelimb movements; in warm (37 degrees C) water, they swam poorly and paddled with all four limbs. To eat small pieces of food, they sat up and used their forepaws as do normal rats, but they frequently dropped the food; they did not use their forepaws to eat large pieces of food. When given powdered food, they first tried to grasp it in their mouth while they scratched at the floor surface with their front limbs; thereafter, they became increasingly proficient in licking it up. Thus, in a narrow range of stimulus conditions, decorticate rats can make movements resembling those of normal rats. They also improve with practice in some (eating powdered food) but not other (forepaw immobility, eating large food pellets) tasks. The study shows that in order to elucidate the role of the cortex in control of motor behavior, it is necessary to obtain "behavior profiles" of each behavior by testing the animals repeatedly and under widely varying test conditions.

Chemicals from Agave sisalana Biomass: Isolation and Identification

Directory of Open Access Journals (Sweden)

Jener David Gonçalves Santos

2015-04-01

Full Text Available Agave sisalana (sisal is known worldwide as a source of hard fibers, and Brazil is the largest producer of sisal. Nonetheless, the process of removing the fibers of the sisal leaf generates 95% waste. In this study, we applied chemical sequential steps (hydrothermal extraction, precipitation, liquid-liquid extraction, crystallization, SiO2 and Sephadex LH 20 column chromatography to obtain pectin, mannitol, succinic acid, kaempferol and a mixture of saponins as raw chemicals from sisal biomass. The structural identification of these compounds was performed though spectrometric methods, such as Infrared (IR, Ultraviolet (UV, Mass spectrometry (MS and Nuclear magnetic resonance (NMR. All the sisal chemicals found in this work are used by both the chemical and pharmaceutical industries as excipients or active principles in products.

Caracterização mecânica e térmica de compósitos de poli (cloreto de vinila reforçados com fibras de sisal Mechanical and thermal characterization of the polyvinyl chloride-sisal fibers composites

Directory of Open Access Journals (Sweden)

Gilson S. Martins

2004-12-01

Full Text Available Compósitos de PVC, plastificados com diferentes sistemas de plastificação e reforçados com fibras de sisal, foram processados em moinho de dois rolos. A influência do tipo e teor do plastificante, do comprimento e do teor das fibras nas propriedades dos compósitos obtidos foi estudada. Dois tipos de plastificantes foram usados, um líquido (do tipo poliéster e um sólido permanente (copolímero etileno/ acetato de vinila/ monóxido de carbono. As fibras usadas foram previamente lavadas com água a 80 °C por uma hora. Os compósitos, com fibras curtas aleatoriamente distribuídas, foram caracterizados através de ensaio mecânico de resistência à tração, microscopia eletrônica de varredura (MEV, e análises térmicas de calorimetria exploratória diferencial (DSC e análise por termogravimetria (TG. O comprimento ótimo de fibra obtido para os compósitos foi de 6 mm. O uso do plastificante sólido mostrou-se viável e promoveu uma maior molhabilidade da fibra pela matriz nos compósitos, principalmente para teores acima de 40 pcr. As análises térmicas mostraram que a substituição do plastificante líquido pelo plastificante sólido não afetou a estabilidade térmica das matrizes e dos compósitos.Composites consisting of flexible polyvinyl chloride (PVC, plasticized with two different types of plasticizers and reinforced with sisal fibers, were processed on a two-roll mixing mill. Two plasticizers were used, a liquid plasticizer (polyester and a permanent solid plasticizer (ethylene/ vinyl acetate/ carbon monoxide copolymer - Elvaloy® , to form two kinds of polymeric matrices. For each one of these matrices, the influence of plasticizers type, plasticizers content, size and quantity of sisal fibers in the composite properties has been studied. The fibers were washed with water at 80 °C during one hour. The composites with randomly distributed short fibers were characterized by mechanical analysis, scanning electron microscopy

Whiskers de fibra de sisal obtidos sob diferentes condições de hidrólise ácida: efeito do tempo e da temperatura de extração Whiskers from sisal fibers obtained under different acid hydrolysis conditions: effect of time and temperature of extraction

Directory of Open Access Journals (Sweden)

Kelcilene B. R. Teodoro

2011-01-01

Full Text Available Neste trabalho, os efeitos de diferentes condições de tempo e temperatura usados para a preparação de whiskers de sisal foram investigados com o objetivo de se determinar a influência destes parâmetros experimentais na morfologia, cristalinidade e estabilidade térmica dos materiais preparados. A obtenção dos whiskers deu-se após o pré-branqueamento da fibra de sisal com solução alcalina de peróxido de hidrogênio. A fibra branqueada foi submetida ao processo de hidrólise com solução de ácido sulfúrico 60% (m/m sob três diferentes condições de temperatura e tempos de extração: 45 °C e 60 minutos (WS45_60; 45 °C e 75 minutos (WS45_75 e 60 °C e 30 minutos (WS60_30. Os whiskers foram caracterizados quanto à morfologia por microscopia eletrônica de transmissão (MET, quanto à cristalinidade (DRX, carga superficial (potencial zeta , teor de enxofre (análise elementar e quanto à estabilidade térmica por termogravimetria (TGA. Os resultados mostraram que os whiskers de sisal apresentaram comprimento e diâmetro médios e 210 nm e 5 nm respectivamente. Devido à alta aglomeração dos whiskers, diferenças relativas às características dimensionais não puderam ser determinadas. Os resultados obtidos revelaram uma forte dependência da cristalinidade final dos whiskers com a temperatura e tempo de extração. O uso de temperatura mais alta (60 °C associado a um menor tempo de extração (30 minutos resulta em whiskers com boa estabilidade térmica (235 °C, maior cristalinidade e sem o comprometimento da estrutura cristalina da celulose.In this work, the effects of different conditions of time and temperature, used for the preparation of whiskers from sisal, were investigated to determine the influence of experimental parameters on morphology, crystallinity and thermal stability of materials prepared. The whiskers were obtained after the bleaching of sisal raw fiber with a solution of hydrogen peroxide alkaline. The

The effect of saline coolant on temperature levels during decortication with a Midas Rex: An in vitro model using sheep cervical vertebrae.

Directory of Open Access Journals (Sweden)

Asher eLivingston

2015-07-01

Full Text Available Decortication of bone with a high speed burr in the absence of coolant may lead to local thermal necrosis and decreased healing ability which may negatively impact clinical outcome. Little data is available on the impact of applying a coolant during the burring process. This study aims to establish an in vitro model to quantitatively assess peak temperatures during endplate preparation with a high speed burr.Six sheep cervical vertebrae were dissected and mounted. Both end plates were used to give a total of 12 sites. Two thermocouples were inserted into each vertebra, 2mm below the end plate surface and a thermal-camera set up to measure surface temperature. A high speed burr (Midas Rex, Medtronic, Fort Worth, TX was used to decorticate the bone in a side to side sweeping pattern, using a matchstick burr (M-8/9MH30 with light pressure. This procedure was repeated while dripping saline onto the burr and bone. Data was compared between groups using a student t-test.Application of coolant at the bone-burr interface during decortication resulted in a significant decrease in final temperature. Without coolant, maximum temperatures 2mm from the surface were not sufficient to cause thermal osteonecrosis, although peak surface temperatures would cause local damage. The use of a high speed burr provides a quick and effective method of vertebral end plate preparation. Thermal damage to the bone can be minimised through the use of light pressure and saline coolant. This has implications for any bone preparation performed with a high speed burr.

The Effect of Saline Coolant on Temperature Levels during Decortication with a Midas Rex: An in Vitro Model Using Sheep Cervical Vertebrae.

Science.gov (United States)

Livingston, Asher; Wang, Tian; Christou, Chris; Pelletier, Matthew H; Walsh, William R

2015-01-01

Decortication of bone with a high-speed burr in the absence of coolant may lead to local thermal necrosis and decreased healing ability, which may negatively impact clinical outcome. Little data are available on the impact of applying a coolant during the burring process. This study aims to establish an in vitro model to quantitatively assess peak temperatures during endplate preparation with a high-speed burr. Six sheep cervical vertebrae were dissected and mounted. Both end plates were used to give a total of 12 sites. Two thermocouples were inserted into each vertebra, 2 mm below the end plate surface and a thermal camera set up to measure surface temperature. A 3 mm high-pneumatic speed burr (Midas Rex, Medtronic, Fort Worth, TX, USA) was used to decorticate the bone in a side to side sweeping pattern, using a matchstick burr (M-8/9MH30) with light pressure. This procedure was repeated while dripping saline onto the burr and bone. Data were compared between groups using a Student's t-test. Application of coolant at the bone-burr interface during decortication resulted in a significant decrease in final temperature. Without coolant, maximum temperatures 2 mm from the surface were not sufficient to cause thermal osteonecrosis, although peak surface temperatures would cause local damage. The use of a high-speed burr provides a quick and an effective method of vertebral end plate preparation. Thermal damage to the bone can be minimized through the use of light pressure and saline coolant. This has implications for any bone preparation performed with a high-speed burr.

Synthesis of Hierarchical Sisal-Like V2O5 with Exposed Stable {001} Facets as Long Life Cathode Materials for Advanced Lithium-Ion Batteries.

Science.gov (United States)

Wu, Naiteng; Du, Wuzhou; Liu, Guilong; Zhou, Zhan; Fu, Hong-Ru; Tang, Qianqian; Liu, Xianming; He, Yan-Bing

2017-12-20

Vanadium pentoxide (V 2 O 5 ) is considered a promising cathode material for advanced lithium-ion batteries owing to its high specific capacity and low cost. However, the application of V 2 O 5 -based electrodes has been hindered because of their inferior conductivity, cycling stability, and power performance. Herein, hierarchical sisal-like V 2 O 5 microstructures consisting of primary one-dimensional (1D) nanobelts with [001] facets orientation growth and rich oxygen vacancies are synthesized through a facile hydrothermal process using polyoxyethylene-20-cetyl-ether as the surface control agent, followed by calcination. The primary 1D nanobelt shortens the transfer path of electrons and ions, and the stable {001} facets could reduce the side reaction at the interface of electrode/electrolyte, simultaneously. Moreover, the formation of low valence state vanadium would generate the oxygen vacancies to facilitate lithium-ion diffusion. As a result, the sisal-like V 2 O 5 manifests excellent electrochemical performances, including high specific capacity (297 mA h g -1 at a current of 0.1 C) and robust cycling performance (capacity fading 0.06% per cycle). This work develops a controllable method to craft the hierarchical sisal-like V 2 O 5 microstructures with excellent high rate and long-term cyclic stability.

Gamma radiation effect on sisal / polyurethane composites without coupling agents

Energy Technology Data Exchange (ETDEWEB)

Vasco, Marina Cardoso; Claro Neto, Salvador; Nascimento, Eduardo Mauro; Azevedo, Elaine, E-mail: marina.mcv@gmail.com [University of Patras (Greece); Universidade de Sao Paulo (USP) Sao Carlos, SP (Brazil); Universidade Tecnologica Federal do Parana (UTFPR), Curitiba, PR (Brazil)

2017-04-15

Natural fibers and polyurethane based composites may present chemical bonding between the components of the polymer and the lignin of the fiber. The incidence of radiation can cause degradation of the polymeric material and alter its mechanical properties. The objective of this study was to obtain and characterize cold pressed composites from polyurethane derived from castor oil and sisal fibers, without coupling agents, through thermogravimetric and mechanical tests, before and after the incidence of 25 kGy dose of gamma radiation. Woven composites that were not irradiated had maximum values of 4.40 GPa for flexural elastic modulus on three point flexural test and dispersed fiber composite that were not irradiated had maximum values of 2.25 GPa. These materials are adequate for use in non-structural applications in radiotherapy and radiodiagnostic rooms. (author)

Estudio del comportamiento de la escayola reforzada con fibras de sisal, para componentes en viviendas de bajo coste

Directory of Open Access Journals (Sweden)

de Oteiza San José, Ignacio

1993-08-01

Full Text Available The present article is a brief description of the work done for the elaboration of the doctoral thesis and its conclusions. Starting from the possibilities of using plaster in developing countries, due to its abundance and low cost, a series of mechanical tests have been carried out in order to learn about the physical and mechanical properties of plaster reinforced with sisal fibres for its future use in components for low cost housing.

El presente artículo es una breve descripción de los trabajos realizados para la elaboración de la tesis doctoral y de las conclusiones de la misma. Partiendo de las posibilidades de utilización en los países en vías de desarrollo del material de escayola, por su abundancia y bajo coste, se llevan a cabo una serie de ensayos mecánicos, con el fin de conocer las propiedades físicas y mecánicas de la escayola reforzada con fibras de sisal, para una futura aplicación en componentes para viviendas de bajo coste.

Gamma radiation effect on sisal / polyurethane composites without coupling agents

Directory of Open Access Journals (Sweden)

Marina Cardoso Vasco

Full Text Available Abstract Natural fibers and polyurethane based composites may present chemical bonding between the components of the polymer and the lignin of the fiber. The incidence of radiation can cause degradation of the polymeric material and alter its mechanical properties. The objective of this study was to obtain and characterize cold pressed composites from polyurethane derived from castor oil and sisal fibers, without coupling agents, through thermogravimetric and mechanical tests, before and after the incidence of 25 kGy dose of gamma radiation. Woven composites that were not irradiated had maximum values of 4.40 GPa for flexural elastic modulus on three point flexural test and dispersed fiber composite that were not irradiated had maximum values of 2.25 GPa. These materials are adequate for use in non-structural applications in radiotherapy and radiodiagnostic rooms.

Uso de fibra natural de sisal em blocos de concreto para alvenaria estrutural

OpenAIRE

Indara Soto Izquierdo

2011-01-01

A utilização de fibras vegetais como reforço constitui um grande interesse na obtenção de novos materiais para a construção civil produto de seu baixo custo, alta disponibilidade e reduzido consumo de energia para sua produção. Este trabalho avalia a incorporação de fibras de sisal, de comprimento 20 e 40 mm, e fração volumétrica de 0,5 e 1%, em concretos para a alvenaria de blocos estruturais e determina o uso destas unidades na execução de prismas e mini-paredes. Foram realizados os testes ...

Ramie (Boehmeria nivea) decortication waste bio-briquette business model canvas with design thinking approach

Science.gov (United States)

Pahlavi, Ghifari Rezka; Purnomo, Dwi; Bunyamin, Anas; Wulandari, Asri Peni

2017-03-01

Ramie (Boehmeria nivea) is a plant that can produce fibers from its stem but in the production process, it still produces waste containing high lignin and cellulose. The high content of these substances can be used as bio-briquette raw material because they can produce carbon and can offer a business opportunity to establish bio-briquette industry. The purpose of this study is to obtain a ramie decortification waste bio-briquette business model because until now there is no bio-briquette has been made from ramie decortication waste as its raw material. This research uses descriptive analysis method with a design thinking approach. The result of this research shows that the business model canvas is designed based on consumer's experience when interacting with the product via customer journey tool in order to get the business model in accordance with customer expectations.

Seasonal abundance of crustaceans associated with artisanal fishery of blue crab (Callinectes sapidus) in Sisal, Yucatan, Mexico

OpenAIRE

Celis-Sánchez, José Alfredo; Estrella-Canto, Arely de Jesús; Poot-López, Gaspar Román; González-Salas, Carlos; López-Rocha, Jorge Alberto

2014-01-01

Seasonal abundance and selectivity of the main crustacean species associated with blue crab fishing was studied at the port of Sisal, Yucatan, Mexico. For this purpose, 52 crab traps were used, which were divided into four parallel transects placed 100, 150, 200 and 250 m of the shoreline. Each transect consisted of 13 traps 20 m from each other. Traps were set at dusk and checked at dawn, standardizing the fishing effort to 17 hours/trap/day. A total of 832 organisms from eight species were ...

Evaluation of anthelmintic activity of liquid waste of Agave sisalana (sisal in goats Avaliação da atividade anti-helmíntica do resíduo líquido de Agave sisalana (sisal em caprinos

Directory of Open Access Journals (Sweden)

Luciana Ferreira Domingues

2010-12-01

Full Text Available It was evaluated the anthelmintic activity of Agave sisalana (sisal juice against gastrointestinal nematodes and its potential toxic effects in goats. In vitro tests showed more than 95% reduction in larval counts of the genus Haemonchus spp. at concentrations between 86.5 and 146.3 mg.mL-1. In vivo the percent reduction of larvae of the fourth (L4 and fifth (L5 stages of Haemonchus, Oesophagostomum and Trichostrongylus was less than 95% in groups GI and GII, and between 80 and 90% in group GIII. A. sisalana juice at the concentrations tested in vitro was effective against gastrointestinal nematodes in goats; however, its anthelmintic efficacy was reduced when administered to animals.Foi avaliada a atividade anti-helmíntica do suco de Agave sisalana (sisal contra nematódeos gastrintestinais e possíveis efeitos tóxicos em caprinos. Nos testes in vitro, encontrou-se redução superior a 95% na contagem de larvas do gênero Haemonchus spp. nas concentrações entre 86,5 e 146,3 mg.mL-1. In vivo, o percentual de redução de larvas de quarto (L4 e quinto (L5 estágios de Haemonchus, Oesophagostomum e Trichostrongylus foi inferior a 95% para o GI e GII, e entre 80 e 90% para o GIII. O suco de A. sisalana nas concentrações testadas in vitro foi efetivo contra nematódeos gastrintestinais de caprinos, apresentando, no entanto, reduzida eficácia anti-helmíntica quando administrado nos animais.

Evaluation gamma radiation in composite sisal fiber- polyurethane derived of castor oil by bending test

International Nuclear Information System (INIS)

Souza, Felipe H. de; Geraldo, Ricardo R.; Vasco, Marina C.; Azevedo, Elaine; Claro Neto, Salvador

2015-01-01

Materials used for making furniture and accessories or positioning in X -ray examination rooms should not exhale volatile organic compounds and are resistant to ionizing radiation. One solution is the use of vegetable fiber and polyurethane composites of vegetable origin, since they are biodegradable, derived from renewable raw materials and have no volatile organic compounds. The main difficulty in developing this material is fiber adhesion with the polymer. The objective of this study is to evaluate the mechanical properties of composite sisal fiber composite, without further treatment, and polyurethane derived from castor oil, with a dose of 25 kGy gamma radiation, subjected to 3 points bending tests. (author)

Efeito da argila calcinada sobre a durabilidade de argamassas reforçadas com fibras curtas de sisal Effect of calcined clay on aging of sisal short fiber reinforced mortar

Directory of Open Access Journals (Sweden)

João de Farias Filho

2010-10-01

Full Text Available O interesse pelo uso de fibras vegetais como reforço de matrizes, à base de cimento, tem crescido em todo o mundo nos últimos anos, sendo limitado pela baixa durabilidade das fibras no meio alcalino. Com o tempo, as fibras podem mineralizar devido à migração de hidróxido de cálcio (CH da matriz para o lúmen e paredes das fibro-células. Procurou-se consumir, no presente estudo, o CH livre utilizando-se resíduo de tijolo moído e metacaulinita em substituição parcial, de 20 e 40% em peso, do cimento portland. Compósitos com fibras de sisal e matrizes cimento-pozolana foram submetidos a ensaios de resistência a flexão, após 28 dias de cura em água, 135 e 180 dias de envelhecimento natural e após 94 ciclos de molhagem e secagem. Os resultados indicaram que é possível consumir todo o CH da matriz, o que resultou na manutenção da tenacidade inicial do compósito e no aumento da sua resistência a flexão após exposição natural ou ciclos de molhagem e secagem.In the last few years a growing interest in the use of sisal fibers as reinforcement in cement based composites has been observed. However, the main concern for its use is related with the durability of the fibers in the alkaline water of concrete as they can mineralize due to the migration of calcium hydroxide to the fiber lumen and cell walls. In this study, the alkalinity of the matrix was reduced using metakaolin and crushed waste calcined clay bricks as cement replacement. The percentage of cement replacement ranged from 20 to 40% on weight basis. Flexural tests were carried out in the composites after 28 days of cure in water, 135 and 180 days of ageing in the open air and after 94 cycles of wetting and drying. These results indicated that the mixture with cement replacement consumed all calcium hydroxide and kept the toughness over time.

Influência da adição e da modificação química de uma carga mineral nanoparticulada nas propriedades mecânicas e no envelhecimento térmico de compósitos poliuretano/sisal Influence of a nanoparticulate mineral filler addition and chemical modification of the mechanical properties and thermal aging of PU/Sisal composites

Directory of Open Access Journals (Sweden)

Maria Roberta O. Pinto

2005-11-01

Full Text Available Este trabalho trata do efeito da hibridização do reforço, através da adição de uma carga mineral (bentonita nanoparticulada, no desempenho mecânico de compósitos poliuretano/sisal contendo 25% em massa de fibras de sisal e moldados por compressão. As propriedades mecânicas, de tração e impacto, dos sistemas compósitos estudados foram avaliadas em função do teor (0-10% em massa e de modificações químicas da carga mineral. Os efeitos do envelhecimento térmico nas propriedades tênseis (sigma, E, épsilon de compósitos selecionados também foram investigados. O reforço mineral (Bentonita sódica Brasgel-PA foi empregado em quatro formas, a saber: a como fornecido (sem tratamento, b tratado com ácido clorídrico (0,6N, c modificado com cloreto de dodecil dimetil benzil amônio (Dodigen e d modificado com brometo de cetil trimetil amônio (Cetremide. Os resultados indicam que a incorporação da bentonita eleva as propriedades mecânicas dos compósitos e que melhores propriedades foram obtidas quando a bentonita foi tratada com o ácido clorídrico. O envelhecimento térmico em tempos curtos (até 4 dias provocou elevação no módulo elástico e resistência na ruptura dos compósitos, o que foi atribuído à pós-cura da matriz. Em tempos longos (32 dias a exposição térmica causou decréscimo nas propriedades tênseis (sigma, E, épsilon dos compósitos investigados, o que foi atribuído à degradação oxidativa da matriz e dos reforços. O compósito mais resistente ao envelhecimento térmico foi o híbrido cuja carga mineral foi organofilizada com o sal Cetremide. Anáslies por DRX e MEV indicam que a estrutura dos compósitos híbridos é um misto de micro e nanocompósito.This work deals with filler hybridization effects, by the addition of a nanoparticulate mineral filler (bentonite, on the mechanical performance of compression molded Polyurethane/sisal composites with 25 wt % fiber content. Composite tensile and

Experimental and numerical research on the potentialities of layered reinforcement configuration of continuous sisal fibers for thin mortar panels

OpenAIRE

Barros, Joaquim A. O.; Silva, Flávio de A.; Toledo-Filho, Romildo D.

2016-01-01

This work is dedicated to the assessment of the flexural capacity of thin mortar panels (about 12 mm thick) reinforced with unidirectional continuous layers of sisal fibers. By adopting five stacked layers, each one involved in a mortar layer of about 1 mm thickness, which constitute a fiber volume of 10%, a maximum flexural strength of 30 MPa was obtained at a deflection of around 1/10 of the specimen’s span length. At this deflection the toughness is 46 times higher the elastic ...

Teknologi Pemanfaatan Serat Daun Nanas Sebagai Alternatif Bahan Baku Tekstil

OpenAIRE

Hidayat, Pratikno

2009-01-01

At present the pineapple plant is widely cultivated in some regions of Indonesia. Nevertheless the plantation of pineapple plants are commonly utilised only for fruit. This paper aim to represent the another benefit of pineaple plants which can be utilised their abundant pineaple leafs to be used for the textile material, known as pineapple leaf fibres. This subject consist of a review of investigation carried out on the method of  making pineapple leaf fibres such as decortication and degumm...

Evaluation gamma radiation in composite sisal fiber- polyurethane derived of castor oil by bending test; Avaliacao da influencia da radiacao gama em compositos de fibra de sisal - poliuretano derivado de oleo de mamona atraves de ensaios de flexao

Energy Technology Data Exchange (ETDEWEB)

Souza, Felipe H. de; Geraldo, Ricardo R.; Vasco, Marina C.; Azevedo, Elaine, E-mail: helunica@yahoo.com.br [Universidade Tecnologica Federal do Parana (UTFPR), Curitiba, PR (Brazil); Claro Neto, Salvador [Universidade de Sao Paulo (USP), Sao Carlos, SP (Brazil). Instituto de Quimica

2015-07-01

Materials used for making furniture and accessories or positioning in X -ray examination rooms should not exhale volatile organic compounds and are resistant to ionizing radiation. One solution is the use of vegetable fiber and polyurethane composites of vegetable origin, since they are biodegradable, derived from renewable raw materials and have no volatile organic compounds. The main difficulty in developing this material is fiber adhesion with the polymer. The objective of this study is to evaluate the mechanical properties of composite sisal fiber composite, without further treatment, and polyurethane derived from castor oil, with a dose of 25 kGy gamma radiation, subjected to 3 points bending tests. (author)

Análise cromossômica em bulbilhos de sisal (Agave spp. cultivados em diferentes municípios baianos, Brasil Chromosomal analysis of immature bulbs of sisal (Agave spp. cultivated in different districts in Bahia, Brazil

Directory of Open Access Journals (Sweden)

Sandra Regina de Oliveira Domingos Queiroz

2012-12-01

Full Text Available O plantio de sisal tornou-se uma das atividades econômicas mais importantes na região do semiárido baiano, onde as adversidades ambientais impedem o plantio de outras culturas. Diante da importância econômica, estudos de citogenética são necessários, pois podem fornecer informações que auxiliem na produção de linhagens melhoradas. A análise de bulbilhos, coletados de cinco localidades diferentes da Bahia, mostrou a presença de indivíduos diplóides e pentaplóides, com comprimento cromossômico variando de 24,56 µm até 0,43 µm nos diferentes exemplares. A formulação cariotípica para o híbrido n° 11648 (2n = 2x = 60, coletado no município de Valente, foi de 2mv + 38m + 10sm + 8st + 2t. Já para os pentaplóides (2n = 5x = 142 c.a. coletadas nos municípios de Conceição do Coité e Valente a classificação cromossômica encontrada foi: 14m + 66sm + 38st + 2a + 22t e 82m + 48sm + 12st, respectivamente. Fatores como maior comprimento genômico, presença de cromossomos acrocêntricos, subtelocêntricos e telocêntricos nos cariótipos bimodais e a diminuição na quantidade de cromossomos grandes com conseqüente aumento no número de cromossomos pequenos podem indicar o andamento de um processo divergente.Sisal plantations have become one of the more important economic activities in the semiarid region of Bahia, where the environmental adversities are too harsh for most other agricultural operations. In the face of economic importance, cytogenetic studies of sisal are necessary because they could provide information that would aid in the production of improved lineages. In this study, the analyses of the immature bulbs, collected from five different areas in Bahia, showed the presence of diploid and pentaploid individuals, with chromosomal lengths varying from 24.56 µm to 0.43 µm in the different samples. The karyotype formulation for the hybrid n° 11648 (2n = 2x = 60, collected in the district of Valente, was 2mv + 38

Mechanical and thermal properties of sisal fiber-reinforced rubber seed oil-based polyurethane composites

International Nuclear Information System (INIS)

Bakare, I.O.; Okieimen, F.E.; Pavithran, C.; Abdul Khalil, H.P.S.; Brahmakumar, M.

2010-01-01

The development of high-performance composite materials from locally sourced and renewable materials was investigated. Rubber seed oil polyurethane resin synthesized using rubber seed monoglyceride derived from glycerolysis of the oil was used as matrix in the composite samples. Rubber seed oil-based polyurethane composite reinforced with unidirectional sisal fibers were prepared and characterized. Results showed that the properties of unidirectional fiber-reinforced rubber seed oil-based polyurethane composites gave good thermal and mechanical properties. Also, the values of tensile strengths and flexural moduli of the polyurethane composites were more than tenfold and about twofold higher than un-reinforced rubber seed oil-based polyurethane. The improved thermal stability and the scanning electron micrographs of the fracture surface of the composites were attributed to good fiber-matrix interaction. These results indicate that high-performance 'all natural products' composite materials can be developed from resources that are readily available locally.

Evaluation of ionic liquid treated sisal (agave sisalana) fiber as sorbent in biodiesel spill

Science.gov (United States)

Costa, E.; Silva, A.; Mattedi, S.

2018-04-01

The global economic development continually demands the use of energy resources, among which various types of oils are widely used. Despite their undeniable economic importance, environmental accidents with these occur frequently. Thus, the search for efficient and low-cost mitigating measures is recurrent. In this context, techniques that use natural adsorbents, such as vegetable fibers, have been studied, since they combine efficiency, selectivity, low cost and sustainability. Studies have been carried out using various types of fibers, natural or chemically treated. The interest in treating the fiber lies in the fact that, changing the chemical structure of the fiber, its oil sorption capacity is increased. Due to the offered advantages, an alternative and promising type of surface treatment using ionic liquids was performed, to the detriment of traditional treatments. Thus, the technical feasibility of the use of sisal fiber treated with ionic liquid for adsorption of biodiesel was studied.

Measurement and analysis of thrust force in drilling sisal-glass fiber reinforced polymer composites

Science.gov (United States)

Ramesh, M.; Gopinath, A.

2017-05-01

Drilling of composite materials is difficult when compared to the conventional materials because of its in-homogeneous nature. The force developed during drilling play a major role in the surface quality of the hole and minimizing the damages around the surface. This paper focuses the effect of drilling parameters on thrust force in drilling of sisal-glass fiber reinforced polymer composite laminates. The quadratic response models are developed by using response surface methodology (RSM) to predict the influence of cutting parameters on thrust force. The adequacy of the models is checked by using the analysis of variance (ANOVA). A scanning electron microscope (SEM) analysis is carried out to analyze the quality of the drilled surface. From the results, it is found that, the feed rate is the most influencing parameter followed by spindle speed and the drill diameter is the least influencing parameter on the thrust force.

EFFECTS OF NaOH MODIFICATION ON THE MECHANICAL ...

African Journals Online (AJOL)

user

characterized for the following tensile strength (TS), modulus of elasticity (MOE), ... showed desirable properties at 10 wt%, where fiber content was in the range of 5 wt% to 30 wt% at interval of 5 wt%. ... baobab fiber chemically is a novel technique that will ..... Hinrichsen G., A Review on Pineapple Leaf Fibers, Sisal.

Effect of acid concentration and pulp properties on hydrolysis reactions of mercerized sisal.

Science.gov (United States)

Lacerda, Talita M; Zambon, Márcia D; Frollini, Elisabete

2013-03-01

The influence of sulfuric acid concentration (H2SO4 5-25%, 100°C), crystallinity and fibers size on the hydrolysis reaction of sisal pulps were investigated, with the goal of evaluating both the liquor composition, as an important step in the production of bioethanol, and the residual non-hydrolyzed pulp, to determine its potential application as materials. Aliquots were withdrawn from the reaction media, and the liquor composition was analyzed by HPLC. The residual non-hydrolyzed pulps were characterized by SEM, their average molar mass and crystallinity index, and their size distribution was determined using a fiber analyzer. Sulfuric acid 25% led to the highest glucose content (approximately 10gL(-1)), and this acid concentration was chosen to evaluate the influence of both the fiber size and crystallinity of the starting pulp on hydrolysis. The results showed that fibers with higher length and lower crystallinity favored glucose production in approximately 12%, with respect to the highly crystalline shorter fibers. Copyright © 2012 Elsevier Ltd. All rights reserved.

Additives effect on chemical composition and quality of sisal co-product silage

Directory of Open Access Journals (Sweden)

Luiz Gustavo Neves Brandão

2013-12-01

Full Text Available Fermentation profile and nutritional value of sisal co-product silage (SC subjected to seven treatments (additives, were evaluated. The SC was ensiled in natura and added with: soy meal, urea, wheat meal, palm kernel cake, A. sisalana dust, licuri cake and cottonseed cake. Experimental silos with capacity for approximately 15 kg of silage, were used. The silos were opened 60 days after ensilage process. It was used a completely randomized design with three replications. The SC in natura present low values of dry mater (DM 12.3% and the additives increased dry matter silages, exception for urea. The SC silage additivated with soybean meal (pH 4.9 and palm kernel cake (butyric acid = 0.07% DM differed, respectively, for pH and butyric acid, compared with in natura SC silage (pH = 4.1 and butyric acid = 0.03% DM. The addition of soybean meal, urea, cottonseed meal, wheat bran and palm kernel, increased crude protein (CP of in natura SC silage. The NDF in silage increased with addition of cottonseed meal or palm kernel cake (60.1 and 66.2% DM in relation in natura SC silage (42.9% DM. The in natura and additivated silages of SC were considered as good or excellent quality.

Hemithoracic Intensity Modulated Radiation Therapy After Pleurectomy/Decortication for Malignant Pleural Mesothelioma: Toxicity, Patterns of Failure, and a Matched Survival Analysis

Energy Technology Data Exchange (ETDEWEB)

Chance, William W. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Rice, David C. [Department of Thoracic and Cardiovascular Surgery, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Allen, Pamela K. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Tsao, Anne S. [Department of Thoracic/Head and Neck Medical Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Fontanilla, Hiral P. [Princeton Radiation Oncology, Monroe Township, New Jersey (United States); Liao, Zhongxing; Chang, Joe Y.; Tang, Chad; Pan, Hubert Y.; Welsh, James W. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Mehran, Reza J. [Department of Thoracic and Cardiovascular Surgery, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Gomez, Daniel R., E-mail: dgomez@mdanderson.org [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States)

2015-01-01

Purpose: To investigate safety, efficacy, and recurrence after hemithoracic intensity modulated radiation therapy after pleurectomy/decortication (PD-IMRT) and after extrapleural pneumonectomy (EPP-IMRT). Methods and Materials: In 2009-2013, 24 patients with mesothelioma underwent PD-IMRT to the involved hemithorax to a dose of 45 Gy, with an optional integrated boost; 22 also received chemotherapy. Toxicity was scored with the Common Terminology Criteria for Adverse Events v4.0. Pulmonary function was compared at baseline, after surgery, and after IMRT. Kaplan-Meier analysis was used to calculate overall survival (OS), progression-free survival (PFS), time to locoregional failure, and time to distant metastasis. Failures were in-field, marginal, or out of field. Outcomes were compared with those of 24 patients, matched for age, nodal status, performance status, and chemotherapy, who had received EPP-IMRT. Results: Median follow-up time was 12.2 months. Grade 3 toxicity rates were 8% skin and 8% pulmonary. Pulmonary function declined from baseline to after surgery (by 21% for forced vital capacity, 16% for forced expiratory volume in 1 second, and 19% for lung diffusion of carbon monoxide [P for all = .01]) and declined still further after IMRT (by 31% for forced vital capacity [P=.02], 25% for forced expiratory volume in 1 second [P=.01], and 30% for lung diffusion of carbon monoxide [P=.01]). The OS and PFS rates were 76% and 67%, respectively, at 1 year and 56% and 34% at 2 years. Median OS (28.4 vs 14.2 months, P=.04) and median PFS (16.4 vs 8.2 months, P=.01) favored PD-IMRT versus EPP-IMRT. No differences were found in grade 4-5 toxicity (0 of 24 vs 3 of 24, P=.23), median time to locoregional failure (18.7 months vs not reached, P not calculable), or median time to distant metastasis (18.8 vs 11.8 months, P=.12). Conclusions: Hemithoracic intensity modulated radiation therapy after pleurectomy/decortication produced little high-grade toxicity but

Er:YAG laser, piezosurgery, and surgical drill for bone decortication during orthodontic mini-implant insertion: primary stability analysis-an animal study.

Science.gov (United States)

Matys, Jacek; Flieger, Rafał; Tenore, Gianluca; Grzech-Leśniak, Kinga; Romeo, Umberto; Dominiak, Marzena

2018-04-01

It is important to identify factors that affect primary stability of orthodontic mini-implants because it determines the success of treatment. We assessed mini-implant primary stability (initial mechanical engagement with the bone) placed in pig jaws. We also assessed mini-implant insertion failure rate (mini-implant fracture, mini-implants to root contact). A total of 80 taper-shaped mini-implants (Absoanchor® Model SH1312-6; Dentos Inc., Daegu, Korea) 6 mm long with a diameter of 1.1 mm were used. Bone decortication was made before mini-implant insertion by means of three different methods: Group G1: Er:YAG laser (LiteTouch®, Light Instruments, Yokneam, Israel) at energy of 300 mJ, frequency 25 Hz, fluence 38.2 J/cm2, cooling 14 ml/min, tip 1.0 × 17 mm, distance 1 mm, time of irradiation 6 s; Group G2: drill (Hager & Meisinger GmbH, Hansemannstr, Germany); Group G3: piezosurgery (Piezotom Solo, Acteon, NJ, USA). In G4 group (control), mini-implants were driven by a self-drilling method. The primary stability of mini-implants was assessed by measuring damping characteristics between the implant and the tapping head of Periotest device (Gulden-Medizinteknik, Eschenweg, Modautal, Germany). The results in range between - 8 to + 9 allowed immediate loading. Significantly lower Periotest value was found in the control group (mean 0.59 ± 1.57, 95% CI 0.7, 2.4) as compared with Er:YAG laser (mean 4.44 ± 1.64, 95% CI 3.6, 5.3), piezosurgery (mean 17.92 ± 2.73, 95% CI 16.5, 19.3), and a drill (mean 5.91 ± 1.52, 95% CI 5.2, 6.6) (p piezosurgery. Decortication of the cortical bone before mini-implant insertion resulted in reduced risk of implant fracture or injury of adjacent teeth. The high initial stability with a smaller diameter of the mini-implant resulted in increased risk of fracture, especially for a self-drilling method.

AVALIAÇÃO DO DESEMPENHO TÉRMICO DE BEZERREIROS COM ECO-FORRO DE PARTÍCULAS DE MADEIRA E FIBRA DE SISAL / EVALUATION OF THE THERMAL PERFORMANCE OF CALVES’ SHELTER WITH ECO-LINING OF WOOD PARTICLES AND SISAL FIBER

Directory of Open Access Journals (Sweden)

M. R. Cabral

2017-09-01

Full Text Available Este trabalho teve como objetivo avaliar o potencial de utilização do eco-forro constituído de painéis de partículas de madeira de maravalha de Pinus spp. e fibras de sisal aglutinados com resina poliuretana à base de óleo de mamona (PU-mamona quando aplicados em bezerreiros cobertos com telhas de fibrocimento. Nesse estudo foi aferida a temperatura interna do bezerreiro, temperatura de globo negro, umidade relativa, no período da primavera, durante 21 dias e determinados os índices de conforto ITGU, ITU e CTR. Os resultados obtidos indicaram que a temperatura de globo negro e os índices de conforto ITGU e CTR dos bezerreiros com eco-forro foi inferior àquelas aferidas em bezerreiros desprovido de forro. As imagens termográficas comprovaram que o eco-forro diminuí a transferência de calor e radiação para o interior da instalação.

Resistência mecânica de compósitos cimentícios leves utilizando resíduos industriais e fibras de sisal Mechanical resistence of lightweight cement composites utilizing industrial residues and fibers of sisal

Directory of Open Access Journals (Sweden)

Nivaldo T. de Arruda Filho

2012-08-01

Full Text Available A valorização de materiais alternativos incorporados com resíduos como opção ao convencional deve possibilitar a geração de um produto com qualidade, estética, produtividade e com potencial de reduzir impactos da poluição ambiental. Este trabalho foi realizado com o objetivo de desenvolver elementos construtivos para forro e divisórias, a partir de matrizes cimentícias com incorporação de resíduos industriais (resíduo cerâmico, etil vinil acetato - EVA e fibras de sisal. Desenvolveram-se técnicas de moldagem em matrizes cimentícias autoadensáveis e se avaliou a resistência mecânica dos novos compósitos. Uma placa com resíduos de EVA foi produzida e, através de trabalhos de reologia, encontrou-se a pasta matriz de revestimento desta placa, com teor adequado de adições pozolânicas e aditivo superplastificante. Avaliaram-se as resistências mecânicas das placas, da pasta matriz de revestimento encontrada, com e sem adição de fibras, e do novo compósito formado pela união desses dois elementos. Utilizou-se a técnica de alinhamento de fibras com o intuito de incrementar resistência ao novo compósito leve. A adição da matriz com fibras alinhadas melhorou a resistência a flexão do novo compósito.The appreciation of alternative materials incorporated in waste as an option to conventional material should enable to generate a product with quality, aesthetics, productivity and reduce the potential impacts of environmental pollution. This study aims to develop constructive elements for ceilings and walls from cementitious matrix incorporating industrial waste (ceramic waste, ethyl vinyl acetate - EVA and sisal fibers. Moulding techniques to produce self-compacting cementitious matrices were developed and the strength of the new composites were evaluated. A plate with EVA waste was produced and through rheology studies, a matrix plaster for coating of plate surface was found, with appropriate content of pozzolanic and

Ovicidal activity of succinic acid isolated from sisal waste (Agave sisalana against gastrointestinal nematodes of goats

Directory of Open Access Journals (Sweden)

Nathália Silva de Souza Santos

Full Text Available ABSTRACT: This study was conducted to evaluate the in vitro anthelmintic activity of the succinic acid (SA isolated from sisal waste against gastrointestinal nematodes of goats, using the egg hatching and larvae motility assays. In addition, potential cytotoxicity of SA on Vero cell cultures was investigated by means of MTT (3-4,5-dimethylthiazol-2-yl, 2,5diphenyltetrazolium bromide test. The SA induced a significant inhibition of egg hatching (P<0.05 at all concentrations tested (60 to 250µg mL-1, and the concentrations to inhibit 50% (EC50 and 90% (EC90 values (mean ± standard deviation were 90.3±2.8 and 130.6±3.5µg mL-1, respectively. The SA has not shown larvicidal activity. The SA was less toxic to the Vero cells, with the mean percentage of cell viability equal to 85±6.2% at the concentration of 130µg mL-1. The results suggested that SA has potential anthelmintic effect; although, more research is needed to confirm its activity in vivo.

Relationships of leaf dark respiration to leaf nitrogen, specific leaf area and leaf life-span: a test across biomes and functional groups.

Science.gov (United States)

Reich, Peter B; Walters, Michael B; Ellsworth, David S; Vose, James M; Volin, John C; Gresham, Charles; Bowman, William D

1998-05-01

Based on prior evidence of coordinated multiple leaf trait scaling, we hypothesized that variation among species in leaf dark respiration rate (R d ) should scale with variation in traits such as leaf nitrogen (N), leaf life-span, specific leaf area (SLA), and net photosynthetic capacity (A max ). However, it is not known whether such scaling, if it exists, is similar among disparate biomes and plant functional types. We tested this idea by examining the interspecific relationships between R d measured at a standard temperature and leaf life-span, N, SLA and A max for 69 species from four functional groups (forbs, broad-leafed trees and shrubs, and needle-leafed conifers) in six biomes traversing the Americas: alpine tundra/subalpine forest, Colorado; cold temperate forest/grassland, Wisconsin; cool temperate forest, North Carolina; desert/shrubland, New Mexico; subtropical forest, South Carolina; and tropical rain forest, Amazonas, Venezuela. Area-based R d was positively related to area-based leaf N within functional groups and for all species pooled, but not when comparing among species within any site. At all sites, mass-based R d (R d-mass ) decreased sharply with increasing leaf life-span and was positively related to SLA and mass-based A max and leaf N (leaf N mass ). These intra-biome relationships were similar in shape and slope among sites, where in each case we compared species belonging to different plant functional groups. Significant R d-mass -N mass relationships were observed in all functional groups (pooled across sites), but the relationships differed, with higher R d at any given leaf N in functional groups (such as forbs) with higher SLA and shorter leaf life-span. Regardless of biome or functional group, R d-mass was well predicted by all combinations of leaf life-span, N mass and/or SLA (r 2 ≥ 0.79, P morphological, chemical and metabolic traits.

Leaf-IT: An Android application for measuring leaf area.

Science.gov (United States)

Schrader, Julian; Pillar, Giso; Kreft, Holger

2017-11-01

The use of plant functional traits has become increasingly popular in ecological studies because plant functional traits help to understand key ecological processes in plant species and communities. This also includes changes in diversity, inter- and intraspecific interactions, and relationships of species at different spatiotemporal scales. Leaf traits are among the most important traits as they describe key dimensions of a plant's life history strategy. Further, leaf area is a key parameter with relevance for other traits such as specific leaf area, which in turn correlates with leaf chemical composition, photosynthetic rate, leaf longevity, and carbon investment. Measuring leaf area usually involves the use of scanners and commercial software and can be difficult under field conditions. We present Leaf-IT, a new smartphone application for measuring leaf area and other trait-related areas. Leaf-IT is free, designed for scientific purposes, and runs on Android 4 or higher. We tested the precision and accuracy using objects with standardized area and compared the area measurements of real leaves with the well-established, commercial software WinFOLIA using the Altman-Bland method. Area measurements of standardized objects show that Leaf-IT measures area with high accuracy and precision. Area measurements with Leaf-IT of real leaves are comparable to those of WinFOLIA. Leaf-IT is an easy-to-use application running on a wide range of smartphones. That increases the portability and use of Leaf-IT and makes it possible to measure leaf area under field conditions typical for remote locations. Its high accuracy and precision are similar to WinFOLIA. Currently, its main limitation is margin detection of damaged leaves or complex leaf morphologies.

Final report on the safety assessment of AloeAndongensis Extract, Aloe Andongensis Leaf Juice,aloe Arborescens Leaf Extract, Aloe Arborescens Leaf Juice, Aloe Arborescens Leaf Protoplasts, Aloe Barbadensis Flower Extract, Aloe Barbadensis Leaf, Aloe Barbadensis Leaf Extract, Aloe Barbadensis Leaf Juice,aloe Barbadensis Leaf Polysaccharides, Aloe Barbadensis Leaf Water, Aloe Ferox Leaf Extract, Aloe Ferox Leaf Juice, and Aloe Ferox Leaf Juice Extract.

Science.gov (United States)

2007-01-01

Plant materials derived from the Aloe plant are used as cosmetic ingredients, including Aloe Andongensis Extract, Aloe Andongensis Leaf Juice, Aloe Arborescens Leaf Extract, Aloe Arborescens Leaf Juice, Aloe Arborescens Leaf Protoplasts, Aloe Barbadensis Flower Extract, Aloe Barbadensis Leaf, Aloe Barbadensis Leaf Extract, Aloe Barbadensis Leaf Juice, Aloe Barbadensis Leaf Polysaccharides, Aloe Barbadensis Leaf Water, Aloe Ferox Leaf Extract, Aloe Ferox Leaf Juice, and Aloe Ferox Leaf Juice Extract. These ingredients function primarily as skin-conditioning agents and are included in cosmetics only at low concentrations. The Aloe leaf consists of the pericyclic cells, found just below the plant's skin, and the inner central area of the leaf, i.e., the gel, which is used for cosmetic products. The pericyclic cells produce a bitter, yellow latex containing a number of anthraquinones, phototoxic compounds that are also gastrointestinal irritants responsible for cathartic effects. The gel contains polysaccharides, which can be acetylated, partially acetylated, or not acetylated. An industry established limit for anthraquinones in aloe-derived material for nonmedicinal use is 50 ppm or lower. Aloe-derived ingredients are used in a wide variety of cosmetic product types at concentrations of raw material that are 0.1% or less, although can be as high as 20%. The concentration of Aloe in the raw material also may vary from 100% to a low of 0.0005%. Oral administration of various anthraquinone components results in a rise in their blood concentrations, wide systemic distribution, accumulation in the liver and kidneys, and excretion in urine and feces; polysaccharide components are distributed systemically and metabolized into smaller molecules. aloe-derived material has fungicidal, antimicrobial, and antiviral activities, and has been effective in wound healing and infection treatment in animals. Aloe barbadensis (also known as Aloe vera)-derived ingredients were not toxic

Is Pleurectomy/Decortication Superior to Extrapleural Pneumonectomy for Patients with Malignant Pleural Mesothelioma? A Single-Institutional Experience.

Science.gov (United States)

Miyazaki, Takuro; Yamasaki, Naoya; Tsuchiya, Tomoshi; Matsumoto, Keitaro; Kamohara, Ryotaro; Hatachi, Go; Nagayasu, Takeshi

2018-04-20

This study was performed to compare the outcome of pleurectomy/decortication (P/D) with that of extrapleural pneumonectomy (EPP) for patients with malignant pleural mesothelioma (MPM). Patients with MPM underwent either P/D or EPP from August 2008 to December 2014. Various clinicopathological factors were analyzed to identify differences between the two procedures. P/D was performed in nine patients and EPP in 30 patients. Most of the patients' background characteristics were not significantly different between the groups. The surgery time (680 vs. 586 min, p = 0.0034) and bleeding volume (4050 vs. 2110 mL, p = 0.002) were significantly greater in P/D than in EPP; however, grade ≥3 complications (44% vs. 33%, p = 0.54) and length of postoperative hospital stay (29 vs. 37 days, p = 0.26) were not significantly different. The median survival time and 2- and 3-year survival rates in all patients were 16.7 months, 28.5%, and 15.3%, respectively. The median survival time and 2- and 3-year survival in the P/D and EPP groups were 22.5 months, 43.8%, and 43.8% and 16.5 months, 24.0%, and 14.4%, respectively (p = 0.13). Survival of patients with MPM remains poor despite multidisciplinary treatment. P/D is comparable with EPP and could be a safe and another surgical treatment for patients with MPM.

Natural sisal fibers derived hierarchical porous activated carbon as capacitive material in lithium ion capacitor

Science.gov (United States)

Yang, Zhewei; Guo, Huajun; Li, Xinhai; Wang, Zhixing; Yan, Zhiliang; Wang, Yansen

2016-10-01

Lithium-ion capacitor (LIC) is a novel advanced electrochemical energy storage (EES) system bridging gap between lithium ion battery (LIB) and electrochemical capacitor (ECC). In this work, we report that sisal fiber activated carbon (SFAC) was synthesized by hydrothermal treatment followed by KOH activation and served as capacitive material in LIC for the first time. Different particle structure, morphology, specific surface area and heteroatoms affected the electrochemical performance of as-prepared materials and corresponding LICs. When the mass ratio of KOH to char precursor was 2, hierarchical porous structured SFAC-2 was prepared and exhibited moderate specific capacitance (103 F g-1 at 0.1 A g-1), superior rate capability and cyclic stability (88% capacity retention after 5000 cycles at 1 A g-1). The corresponding assembled LIC (LIC-SC2) with optimal comprehensive electrochemical performance, displayed the energy density of 83 Wh kg-1, the power density of 5718 W kg-1 and superior cyclic stability (92% energy density retention after 1000 cycles at 0.5 A g-1). It is worthwhile that the source for activated carbon is a natural and renewable one and the synthesis method is eco-friendly, which facilitate that hierarchical porous activated carbon has potential applications in the field of LIC and other energy storage systems.

Maize YABBY genes drooping leaf1 and drooping leaf2 affect agronomic traits by regulating leaf architecture

Science.gov (United States)

Leaf architectural traits, such as length, width and angle, directly influence canopy structure and light penetration, photosynthate production and overall yield. We discovered and characterized a maize (Zea mays) mutant with aberrant leaf architecture we named drooping leaf1 (drl1), as leaf blades ...

The influence of irradiation treatment on gossypol and protein digestibility of decorticated cottonseed meal for Broiler chicks

International Nuclear Information System (INIS)

Farag, M.D.H.

2000-01-01

The Effect of gamma irradiation (5-20 kGy) on the chemical composition, soluble protein, available lysine, gossypol, in-vitro and in vivo digestibility of decorticated cottonseed meal (CSM) and the performance of broilers fed processed CSM were investigated. Radiation treatment of CSM at dose levels of 5, 10, 15 and 20 kGy did not affect moisture, crude protein, ether extract, crude fiber, ash and NFW content. However, the treatment reduced soluble protein by 4.18, 7.82, 10.91, 13.46%, respectively. Fluorodinitrobenzene-available lysine concentration reduced by 4.48, 8.12, 17.65 and 21.29% respectively. The concentrations of total gossypol decreased by 7.97, 15.78, 19.92 and 25.39% and free gossypol by 3.74, 7.85, 18.43 and 28.01%, respectively. The digestibility of CSM protein was increased by 5.3, 9.0, 16.6 and 17.2%, for in-vitro digestibility and by 4.8, 7.3, 9.4 and 12.9% for in-vivo due to treatment with 5,10, 15 and 20 kGy, respectively. From 7 to 42 days, arbor acres broilers were freely given iso energetic and iso nitrogenous : corn-soy control diet or diets containing 300 g kg -1 raw or irradiated CSM at 4, 15 or 20 kGy. Intake of raw CSM affected growth, feed intake and feed conversion as compared with birds receiving the control diet

"Breath figures" on leaf surfaces-formation and effects of microscopic leaf wetness.

Science.gov (United States)

Burkhardt, Juergen; Hunsche, Mauricio

2013-01-01

"Microscopic leaf wetness" means minute amounts of persistent liquid water on leaf surfaces which are invisible to the naked eye. The water is mainly maintained by transpired water vapor condensing onto the leaf surface and to attached leaf surface particles. With an estimated average thickness of less than 1 μm, microscopic leaf wetness is about two orders of magnitude thinner than morning dewfall. The most important physical processes which reduce the saturation vapor pressure and promote condensation are cuticular absorption and the deliquescence of hygroscopic leaf surface particles. Deliquescent salts form highly concentrated solutions. Depending on the type and concentration of the dissolved ions, the physicochemical properties of microscopic leaf wetness can be considerably different from those of pure water. Microscopic leaf wetness can form continuous thin layers on hydrophobic leaf surfaces and in specific cases can act similar to surfactants, enabling a strong potential influence on the foliar exchange of ions. Microscopic leaf wetness can also enhance the dissolution, the emission, and the reaction of specific atmospheric trace gases e.g., ammonia, SO2, or ozone, leading to a strong potential role for microscopic leaf wetness in plant/atmosphere interaction. Due to its difficult detection, there is little knowledge about the occurrence and the properties of microscopic leaf wetness. However, based on the existing evidence and on physicochemical reasoning it can be hypothesized that microscopic leaf wetness occurs on almost any plant worldwide and often permanently, and that it significantly influences the exchange processes of the leaf surface with its neighboring compartments, i.e., the plant interior and the atmosphere. The omission of microscopic water in general leaf wetness concepts has caused far-reaching, misleading conclusions in the past.

Effect of Plant Growth Regulators on Leaf Number, Leaf Area and Leaf Dry Matter in Grape

Directory of Open Access Journals (Sweden)

Zahoor Ahmad BHAT

2011-03-01

Full Text Available Influence of phenylureas (CPPU and brassinosteriod (BR along with GA (gibberellic acid were studied on seedless grape vegetative characteristics like leaf number, leaf area and leaf dry matter. Growth regulators were sprayed on the vines either once (7 days after fruit set or 15 days after fruit set or twice (7+15 days after fruit set. CPPU 2 ppm+BR 0.4 ppm+GA 25 ppm produced maximum number of leaves (18.78 while as untreated vines produced least leaf number (16.22 per shoot. Maximum leaf area (129.70 cm2 and dry matter content (26.51% was obtained with higher CPPU (3 ppm and BR (0.4 ppm combination along with GA 25 ppm. Plant growth regulators whether naturally derived or synthetic are used to improve the productivity and quality of grapes. The relatively high value of grapes justifies more expensive inputs. A relatively small improvement in yield or fruit quality can justify the field application of a very costly product. Application of new generation growth regulators like brassinosteroids and phenylureas like CPPU have been reported to increase the leaf number as well as leaf area and dry matter thereby indirectly influencing the fruit yield and quality in grapes.

Lipophilic extractives from several nonwoody lignocellulosic crops (flax, hemp, sisal, abaca) and their fate during alkaline pulping and TCF/ECF bleaching.

Science.gov (United States)

Marques, Gisela; del Río, José C; Gutiérrez, Ana

2010-01-01

The fate of lipophilic extractives from several nonwoody species (flax, hemp, sisal and abaca) used for the manufacturing of cellulose pulps, was studied during soda/anthraquinone (AQ) pulping and totally chorine free (TCF) and elemental chlorine free (ECF) bleaching. With this purpose, the lipophilic extracts from the raw materials and their unbleached and bleached industrial pulps, were analyzed by gas chromatography-mass spectrometry. Aldehydes, hydroxyfatty acids and esterified compounds such as ester waxes, sterol esters and alkylferulates strongly decreased after soda/AQ pulping while alkanes, alcohols, free sterols and sterol glycosides survived the cooking process. Among the lipophilic extractives that remained in the unbleached pulps, some amounts of free sterols were still present in the TCF pulps whereas they were practically absent in the ECF pulps. Sterol glycosides were also removed after both TCF and ECF bleaching. By contrast, saturated fatty acids, fatty alcohols and alkanes were still present in both bleached pulps.

Why do leaf-tying caterpillars abandon their leaf ties?

Directory of Open Access Journals (Sweden)

Michelle Sliwinski

2013-09-01

Full Text Available Leaf-tying caterpillars act as ecosystem engineers by building shelters between overlapping leaves, which are inhabited by other arthropods. Leaf-tiers have been observed to leave their ties and create new shelters (and thus additional microhabitats, but the ecological factors affecting shelter fidelity are poorly known. For this study, we explored the effects of resource limitation and occupant density on shelter fidelity and assessed the consequences of shelter abandonment. We first quantified the area of leaf material required for a caterpillar to fully develop for two of the most common leaf-tiers that feed on white oak, Quercus alba. On average, Psilocorsis spp. caterpillars consumed 21.65 ± 0.67 cm2 leaf material to complete development. We also measured the area of natural leaf ties found in a Maryland forest, to determine the distribution of resources available to caterpillars in situ. Of 158 natural leaf ties examined, 47% were too small to sustain an average Psilocorsis spp. caterpillar for the entirety of its development. We also manipulated caterpillar densities within experimental ties on potted trees to determine the effects of cohabitants on the likelihood of a caterpillar to leave its tie. We placed 1, 2, or 4 caterpillars in ties of a standard size and monitored the caterpillars twice daily to track their movement. In ties with more than one occupant, caterpillars showed a significantly greater propensity to leave their tie, and left sooner and at a faster rate than those in ties as single occupants. To understand the consequences of leaf tie abandonment, we observed caterpillars searching a tree for a site to build a shelter in the field. This is a risky behavior, as 17% of the caterpillars observed died while searching for a shelter site. Caterpillars that successfully built a shelter traveled 110 ± 20 cm and took 28 ± 7 min to find a suitable site to build a shelter. In conclusion, leaf-tying caterpillars must frequently

Can Leaf Spectroscopy Predict Leaf and Forest Traits Along a Peruvian Tropical Forest Elevation Gradient?

Science.gov (United States)

Doughty, Christopher E.; Santos-Andrade, P. E.; Goldsmith, G. R.; Blonder, B.; Shenkin, A.; Bentley, L. P.; Chavana-Bryant, C.; Huaraca-Huasco, W.; Díaz, S.; Salinas, N.; Enquist, B. J.; Martin, R.; Asner, G. P.; Malhi, Y.

2017-11-01

High-resolution spectroscopy can be used to measure leaf chemical and structural traits. Such leaf traits are often highly correlated to other traits, such as photosynthesis, through the leaf economics spectrum. We measured VNIR (visible-near infrared) leaf reflectance (400-1,075 nm) of sunlit and shaded leaves in 150 dominant species across ten, 1 ha plots along a 3,300 m elevation gradient in Peru (on 4,284 individual leaves). We used partial least squares (PLS) regression to compare leaf reflectance to chemical traits, such as nitrogen and phosphorus, structural traits, including leaf mass per area (LMA), branch wood density and leaf venation, and "higher-level" traits such as leaf photosynthetic capacity, leaf water repellency, and woody growth rates. Empirical models using leaf reflectance predicted leaf N and LMA (r2 > 30% and %RMSE < 30%), weakly predicted leaf venation, photosynthesis, and branch density (r2 between 10 and 35% and %RMSE between 10% and 65%), and did not predict leaf water repellency or woody growth rates (r2<5%). Prediction of higher-level traits such as photosynthesis and branch density is likely due to these traits correlations with LMA, a trait readily predicted with leaf spectroscopy.

Leaf size and leaf display of thirty-eight tropical tree species

NARCIS (Netherlands)

Poorter, L.; Rozendaal, D.M.A.

2008-01-01

Trees forage for light through optimal leaf display. Effective leaf display is determined by metamer traits (i.e., the internode, petiole, and corresponding leaf), and thus these traits strongly co-determine carbon gain and as a result competitive advantage in a light-limited environment. We

‘Breath figures’ on leaf surfaces – formation and effects of microscopic leaf wetness

Directory of Open Access Journals (Sweden)

Jürgen eBurkhardt

2013-10-01

Full Text Available ‘Microscopic leaf wetness’ means minute amounts of persistent liquid water on leaf surfaces which are invisible to the naked eye. The water is mainly maintained by transpired water vapor condensing onto the leaf surface and to attached leaf surface particles. With an estimated average thickness of less than 1 µm, microscopic leaf wetness it is about 2 orders of magnitude thinner than morning dewfall. The most important physical processes which reduce the saturation vapor pressure and promote condensation are cuticular absorption and the deliquescence of hygroscopic leaf surface particles. Deliquescent salts form highly concentrated solutions. Depending on the amount and concentration of the dissolved ions, the physicochemical properties of microscopic leaf wetness can be considerably different from those of pure water. Microscopic leaf wetness can form continuous thin layers on hydrophobic leaf surfaces and in specific cases can act similar to surfactants, enabling a strong potential influence on the foliar exchange of ions. Microscopic leaf wetness can also enhance the dissolution, the emission, and the reaction of specific atmospheric trace gases e.g. ammonia, SO2, or ozone, leading to a strong potential role for microscopic leaf wetness in plant/atmosphere interaction. Due to its difficult detection, there is little knowledge about the occurrence and the properties of microscopic leaf wetness. However, based on the existing evidence and on physicochemical reasoning it can be hypothesized that microscopic leaf wetness occurs on almost any plant worldwide and often permanently, and that it significantly influences the exchange processes of the leaf surface with its neighboring compartments, i.e., the plant interior and the atmosphere. The omission of microscopic water in general leaf wetness concepts has caused far-reaching, misleading conclusions in the past.

Impact test on natural fiber reinforced polymer composite materials

Directory of Open Access Journals (Sweden)

D. Chandramohan

2013-06-01

Full Text Available In this research, natural fibers like Sisal (Agave sisalana, Banana (Musa sepientum & Roselle (Hibiscus sabdariffa , Sisal and banana (hybrid , Roselle and banana (hybrid and Roselle and sisal (hybrid are fabricated with bio epoxy resin using molding method. In this work, impact strength of Sisal and banana (hybrid, Roselle and banana (hybridand Roselle and sisal (hybrid composite at dry and wet conditions were studied. Impact test were conducted izod impact testing machine. In this work micro structure of the specimens are scanned by the Scanning Electron Microscope.

Influence of Pleurectomy and Decortication in Health-Related Quality of Life Among Patients with Malignant Pleural Mesothelioma.

Science.gov (United States)

Vigneswaran, Wickii T; Kircheva, Diana Y; Rodrigues, Adrian E; Watson, Sydeaka; Celauro, Amy Durkin; Rose, Berkley; Kindler, Hedy L; Husain, Aliya N

2018-04-01

Complete macroscopic resection surgery, pleurectomy and decortication (PD) improve survival in selected patients with malignant pleural mesothelioma (MPM). Yet its value has been questioned because of concern that this extensive surgical procedure may disrupt health-related quality of life (HRQoL). HRQoL was studied in patients undergoing PD surgery for MPM using EORTC QLQ-C30 instrument at baseline (prior to surgery), 1, 4-5, 7-8, and 10-11 months following surgery. Global health and variables in function and symptom domains were investigated. Sub-groups analyses were performed for ECOG performance status (PS), histological sub-types and pathological tumor volume (pTV). Within-patient comparisons to baseline scores were made using Wilcoxon signed-rank test. Trends over time were evaluated using Cuzick's nonparametric test. There were 114 patients with median age of 70 years (range: 50-88) and PS 0: 35 (30.7%), epithelioid histology: 61 (53.5%) and volume <600 ml: 58 (50.9%). Patients with good PS (PS 0), epithelioid histology and small pTV had greater level of functioning and were less symptomatic at baseline. Overall global health worsened at the first postoperative month (p = 0.0005) with subsequent improvement. Non-epithelioid histology and patients with large pTV demonstrated greater improvement in global health, function and symptoms domains following a PD. At baseline, the overall health-related quality of life, function and symptom domains were adversely affected in non-epithelioid histology and patients with large pTV. However, greatest improvement in global health, symptom and function domains were observed first month after PD and during the follow-up in these sub-groups.

Leaf habit and woodiness regulate different leaf economy traits at a given nutrient supply.

Science.gov (United States)

Ordoñez, Jenny C; van Bodegom, Peter M; Witte, Jan-Philip M; Bartholomeus, Ruud P; van Dobben, Han F; Aerts, Rien

2010-11-01

The large variation in the relationships between environmental factors and plant traits observed in natural communities exemplifies the alternative solutions that plants have developed in response to the same environmental limitations. Qualitative attributes, such as growth form, woodiness, and leaf habit can be used to approximate these alternative solutions. Here, we quantified the extent to which these attributes affect leaf trait values at a given resource supply level, using measured plant traits from 105 different species (254 observations) distributed across 50 sites in mesic to wet plant communities in The Netherlands. For each site, soil total N, soil total P, and water supply estimates were obtained by field measurements and modeling. Effects of growth forms, woodiness, and leaf habit on relations between leaf traits (SLA, specific leaf area; LNC, leaf nitrogen concentration; and LPC, leaf phosphorus concentration) vs. nutrient and water supply were quantified using maximum-likelihood methods and Bonferroni post hoc tests. The qualitative attributes explained 8-23% of the variance within sites in leaf traits vs. soil fertility relationships, and therefore they can potentially be used to make better predictions of global patterns of leaf traits in relation to nutrient supply. However, at a given soil fertility, the strength of the effect of each qualitative attribute was not the same for all leaf traits. These differences may imply a differential regulation of the leaf economy traits at a given nutrient supply, in which SLA and LPC seem to be regulated in accordance to changes in plant size and architecture while LNC seems to be primarily regulated at the leaf level by factors related to leaf longevity.

Effect of Addition of Moringa Leaf By-Product (Leaf-Waste) on ...

African Journals Online (AJOL)

The effects of incorporation of Moringa leaf fibre (a by-product of leaf processing which contains 24% Crude Fibre by dry weight at 0, 5 and 10 % substitution of wheat flour in cookies was investigated. Three products containing wheat flour: Moringa leaf fibre ratios of 100:0, 95:5, and 90:10 respectively were prepared, and a ...

Global variability in leaf respiration in relation to climate and leaf traits

Science.gov (United States)

Atkin, Owen K.

2015-04-01

Leaf respiration plays a vital role in regulating ecosystem functioning and the Earth's climate. Because of this, it is imperative that that Earth-system, climate and ecosystem-level models be able to accurately predict variations in rates of leaf respiration. In the field of photosynthesis research, the F/vC/B model has enabled modellers to accurately predict variations in photosynthesis through time and space. By contrast, we lack an equivalent biochemical model to predict variations in leaf respiration. Consequently, we need to rely on phenomenological approaches to model variations in respiration across the Earth's surface. Such approaches require that we develop a thorough understanding of how rates of respiration vary among species and whether global environmental gradients play a role in determining variations in leaf respiration. Dealing with these issues requires that data sets be assembled on rates of leaf respiration in biomes across the Earth's surface. In this talk, I will use a newly-assembled global database on leaf respiration and associated traits (including photosynthesis) to highlight variation in leaf respiration (and the balance between respiration and photosynthesis) across global gradients in growth temperature and aridity.

Effect of nitrogen supply on leaf appearance, leaf growth, leaf nitrogen economy and photosynthetic capacity in maize (Zea mays L.)

NARCIS (Netherlands)

Vos, J.; Putten, van der P.E.L.; Birch, C.J.

2005-01-01

Leaf area growth and nitrogen concentration per unit leaf area, Na (g m-2 N) are two options plants can use to adapt to nitrogen limitation. Previous work indicated that potato (Solanum tuberosum L.) adapts the size of leaves to maintain Na and photosynthetic capacity per unit leaf area. This paper

SU-F-T-350: Continuous Leaf Optimization (CLO) for IMRT Leaf Sequencing

Energy Technology Data Exchange (ETDEWEB)

Long, T; Chen, M; Jiang, S; Lu, W [UT Southwestern Medical Center, Dallas, TX (United States)

2016-06-15

Purpose: To study a new step-and-shoot IMRT leaf sequencing model that avoids the two main pitfalls of conventional leaf sequencing: (1) target fluence being stratified into a fixed number of discrete levels and/or (2) aperture leaf positions being restricted to a discrete set of locations. These assumptions induce error into the sequence or reduce the feasible region of potential plans, respectively. Methods: We develop a one-dimensional (single leaf pair) methodology that does not make assumptions (1) or (2) that can be easily extended to a multi-row model. The proposed continuous leaf optimization (CLO) methodology takes in an existing set of apertures and associated intensities, or solution “seed,” and improves the plan without the restrictiveness of 1or (2). It then uses a first-order descent algorithm to converge onto a locally optimal solution. A seed solution can come from models that assume (1) and (2), thus allowing the CLO model to improve upon existing leaf sequencing methodologies. Results: The CLO model was applied to 208 generated target fluence maps in one dimension. In all cases for all tested sequencing strategies, the CLO model made improvements on the starting seed objective function. The CLO model also was able to keep MUs low. Conclusion: The CLO model can improve upon existing leaf sequencing methods by avoiding the restrictions of (1) and (2). By allowing for more flexible leaf positioning, error can be reduced when matching some target fluence. This study lays the foundation for future models and solution methodologies that can incorporate continuous leaf positions explicitly into the IMRT treatment planning model. Supported by Cancer Prevention & Research Institute of Texas (CPRIT) - ID RP150485.

On the temporal variation of leaf magnetic parameters: seasonal accumulation of leaf-deposited and leaf-encapsulated particles of a roadside tree crown.

Science.gov (United States)

Hofman, Jelle; Wuyts, Karen; Van Wittenberghe, Shari; Samson, Roeland

2014-09-15

Understanding the accumulation behaviour of atmospheric particles inside tree leaves is of great importance for the interpretation of biomagnetic monitoring results. In this study, we evaluated the temporal variation of the saturation isothermal remanent magnetisation (SIRM) of leaves of a roadside urban Platanus × acerifolia Willd. tree in Antwerp, Belgium. We hereby examined the seasonal development of the total leaf SIRM signal as well as the leaf-encapsulated fraction of the deposited dust, by washing the leaves before biomagnetic analysis. On average 38% of the leaf SIRM signal was exhibited by the leaf-encapsulated particles. Significant correlations were found between the SIRM and the cumulative daily average atmospheric PM10 and PM2.5 measurements. Moreover, a steady increase of the SIRM throughout the in-leaf season was observed endorsing the applicability of biomagnetic monitoring as a proxy for the time-integrated PM exposure of urban tree leaves. Strongest correlations were obtained for the SIRM of the leaf-encapsulated particles which confirms the dynamic nature of the leaf surface-accumulated particles. Copyright © 2014 Elsevier B.V. All rights reserved.

Effect of Wind on the Relation of Leaf N, P Stoichiometry with Leaf Morphology in Quercus Species

Directory of Open Access Journals (Sweden)

Peng Zhang

2018-02-01

Full Text Available Leaf nitrogen (N and phosphorus (P stoichiometry correlates closely to leaf morphology, which is strongly impacted by wind at multiple scales. However, it is not clear how leaf N, P stoichiometry and its relationship to leaf morphology changes with wind load. We determined the leaf N and P concentrations and leaf morphology—including specific leaf area (SLA and leaf dissection index (LDI—for eight Quercus species under a simulated wind load for seven months. Leaf N and P concentrations increased significantly under these conditions for Quercus acutissima, Quercus rubra, Quercus texana, and Quercus palustris—which have elliptic leaves—due to their higher N, P requirements and a resultant leaf biomass decrease, which is a tolerance strategy for Quercus species under a wind load. Leaf N:P was relatively stable under wind for all species, which supports stoichiometric homeostasis. Leaf N concentrations showed a positive correlation to SLA, leaf N and P concentrations showed positive correlations to LDI under each wind treatment, and the slope of correlations was not affected by wind, which indicates synchronous variations between leaf stoichiometry and leaf morphology under wind. However, the intercept of correlations was affected by wind, and leaf N and P use efficiency decreased under the wind load, which suggests that the Quercus species changes from “fast investment-return” in the control to “slow investment-return” under windy conditions. These results will be valuable to understanding functional strategies for plants under varying wind loads, especially synchronous variations in leaf traits along a wind gradient.

Are leaf physiological traits related to leaf water isotopic enrichment in restinga woody species?

Directory of Open Access Journals (Sweden)

BRUNO H.P. ROSADO

2013-09-01

Full Text Available During plant-transpiration, water molecules having the lighter stable isotopes of oxygen and hydrogen evaporate and diffuse at a faster rate through the stomata than molecules having the heavier isotopes, which cause isotopic enrichment of leaf water. Although previous models have assumed that leaf water is well-mixed and isotopically uniform, non-uniform stomatal closure, promoting different enrichments between cells, and different pools of water within leaves, due to morpho-physiological traits, might lead to inaccuracies in isotopic models predicting leaf water enrichment. We evaluate the role of leaf morpho-physiological traits on leaf water isotopic enrichment in woody species occurring in a coastal vegetation of Brazil known as restinga. Hydrogen and oxygen stable isotope values of soil, plant stem and leaf water and leaf traits were measured in six species from restinga vegetation during a drought and a wet period. Leaf water isotopic enrichment relative to stem water was more homogeneous among species during the drought in contrast to the wet period suggesting convergent responses to deal to temporal heterogeneity in water availability. Average leaf water isotopic enrichment relative to stem water during the drought period was highly correlated with relative apoplastic water content. We discuss this observation in the context of current models of leaf water isotopic enrichment as a function of the Péclet effect. We suggest that future studies should include relative apoplastic water content in isotopic models.

Are leaf physiological traits related to leaf water isotopic enrichment in restinga woody species?

Science.gov (United States)

Rosado, Bruno H P; De Mattos, Eduardo A; Sternberg, Leonel Da S L

2013-09-01

During plant-transpiration, water molecules having the lighter stable isotopes of oxygen and hydrogen evaporate and diffuse at a faster rate through the stomata than molecules having the heavier isotopes, which cause isotopic enrichment of leaf water. Although previous models have assumed that leaf water is well-mixed and isotopically uniform, non-uniform stomatal closure, promoting different enrichments between cells, and different pools of water within leaves, due to morpho-physiological traits, might lead to inaccuracies in isotopic models predicting leaf water enrichment. We evaluate the role of leaf morpho-physiological traits on leaf water isotopic enrichment in woody species occurring in a coastal vegetation of Brazil known as restinga. Hydrogen and oxygen stable isotope values of soil, plant stem and leaf water and leaf traits were measured in six species from restinga vegetation during a drought and a wet period. Leaf water isotopic enrichment relative to stem water was more homogeneous among species during the drought in contrast to the wet period suggesting convergent responses to deal to temporal heterogeneity in water availability. Average leaf water isotopic enrichment relative to stem water during the drought period was highly correlated with relative apoplastic water content. We discuss this observation in the context of current models of leaf water isotopic enrichment as a function of the Péclet effect. We suggest that future studies should include relative apoplastic water content in isotopic models.

How do leaf veins influence the worldwide leaf economic spectrum? Review and synthesis.

Science.gov (United States)

Sack, Lawren; Scoffoni, Christine; John, Grace P; Poorter, Hendrik; Mason, Chase M; Mendez-Alonzo, Rodrigo; Donovan, Lisa A

2013-10-01

Leaf vein traits are implicated in the determination of gas exchange rates and plant performance. These traits are increasingly considered as causal factors affecting the 'leaf economic spectrum' (LES), which includes the light-saturated rate of photosynthesis, dark respiration, foliar nitrogen concentration, leaf dry mass per area (LMA) and leaf longevity. This article reviews the support for two contrasting hypotheses regarding a key vein trait, vein length per unit leaf area (VLA). Recently, Blonder et al. (2011, 2013) proposed that vein traits, including VLA, can be described as the 'origin' of the LES by structurally determining LMA and leaf thickness, and thereby vein traits would predict LES traits according to specific equations. Careful re-examination of leaf anatomy, published datasets, and a newly compiled global database for diverse species did not support the 'vein origin' hypothesis, and moreover showed that the apparent power of those equations to predict LES traits arose from circularity. This review provides a 'flux trait network' hypothesis for the effects of vein traits on the LES and on plant performance, based on a synthesis of the previous literature. According to this hypothesis, VLA, while virtually independent of LMA, strongly influences hydraulic conductance, and thus stomatal conductance and photosynthetic rate. We also review (i) the specific physiological roles of VLA; (ii) the role of leaf major veins in influencing LES traits; and (iii) the role of VLA in determining photosynthetic rate per leaf dry mass and plant relative growth rate. A clear understanding of leaf vein traits provides a new perspective on plant function independently of the LES and can enhance the ability to explain and predict whole plant performance under dynamic conditions, with applications towards breeding improved crop varieties.

An evolutionary perspective on leaf economics : Phylogenetics of leaf mass per area in vascular plants

NARCIS (Netherlands)

Flores, Olivier; Garnier, Eric; Wright, Ian J.; Reich, Peter B.; Pierce, Simon; Diaz, Sandra; Pakeman, Robin J.; Rusch, Graciela M.; Bernard-Verdier, Maud; Testi, Baptiste; Bakker, Jan P.; Bekker, Renee M.; Cerabolini, Bruno E. L.; Ceriani, Roberta M.; Cornu, Guillaume; Cruz, Pablo; Delcamp, Matthieu; Dolezal, Jiri; Eriksson, Ove; Fayolle, Adeline; Freitas, Helena; Golodets, Carly; Gourlet-Fleury, Sylvie; Hodgson, John G.; Brusa, Guido; Kleyer, Michael; Kunzmann, Dieter; Lavorel, Sandra; Papanastasis, Vasilios P.; Perez-Harguindeguy, Natalia; Vendramini, Fernanda; Weiher, Evan

In plant leaves, resource use follows a trade-off between rapid resource capture and conservative storage. This "worldwide leaf economics spectrum" consists of a suite of intercorrelated leaf traits, among which leaf mass per area, LMA, is one of the most fundamental as it indicates the cost of leaf

Easy Leaf Area: Automated digital image analysis for rapid and accurate measurement of leaf area.

Science.gov (United States)

Easlon, Hsien Ming; Bloom, Arnold J

2014-07-01

Measurement of leaf areas from digital photographs has traditionally required significant user input unless backgrounds are carefully masked. Easy Leaf Area was developed to batch process hundreds of Arabidopsis rosette images in minutes, removing background artifacts and saving results to a spreadsheet-ready CSV file. • Easy Leaf Area uses the color ratios of each pixel to distinguish leaves and calibration areas from their background and compares leaf pixel counts to a red calibration area to eliminate the need for camera distance calculations or manual ruler scale measurement that other software methods typically require. Leaf areas estimated by this software from images taken with a camera phone were more accurate than ImageJ estimates from flatbed scanner images. • Easy Leaf Area provides an easy-to-use method for rapid measurement of leaf area and nondestructive estimation of canopy area from digital images.

Leaf anatomical traits determine the 18O enrichment of leaf water in coastal halophytes

Science.gov (United States)

Liang, J.; Lin, G., Sr.; Sternberg, L. O.

2017-12-01

Foliar anatomical adaptations to high-salinity environment in mangroves may be recorded by leaf water isotopes. Recent studies observed that a few mangrove species have lower 18O enrichment of leaf water (ΔL) relative to source water than the adjacent terrestrial trees, but what factors actually control this phenomenon is still disputable at present. To resolve this issue, we collected 15 species of true mangrove plants, 14 species of adjacent freshwater trees and 4 species of semi-mangrove plants at five study sites on the southeastern coast of China. Leaf stomatal density and pore size, water content, ΔL and other related leaf physiological traits were determined for the selected leaves of these plants. Our results confirmed that ΔL values of mangroves were generally 3 4 ‰ lower than those of the adjacent freshwater or semi-mangrove species. Higher leaf water per area (LWC) and lower leaf stomatal density (LS) of mangroves played co-dominant roles in lowering ΔL through elongating effective leaf mixing length by about 20%. The Péclet model incorporated by LWC and LS performed well in predicting ΔL. The demonstrated general law between leaf anatomy and ΔL in this paper based on a large pool of species bridges the gap between leaf functional traits and metabolic proxies derived ΔL, which will have considerable potential applications in vegetation succession and reconstruction of paleoclimate research.

Effects of leaf movement on leaf temperature, transpiration and radiation interception in soybean under water stress conditions

International Nuclear Information System (INIS)

Isoda, A.; Wang, P.

2001-01-01

Varietal differences in leaf movement were examined in terms of radiation interception, leaf temperature and transpiration under water stressed conditions. Five cultivars (Qindou 7232, Gaofei 16, Dongnong 87 - 138, 8285 - 8 and 8874) were grown in a concrete frame field in Xinjiang, China. Irrigation treatments (irrigation and no irrigation) were made from the flowering to the pod filling stage. A leaflet in the uppermost layer of the canopy was restrained horizontally. Leaf temperatures, transpiration rate (stem sap flow rate of the main stem per unit leaf area) and intercepted radiation of each leaflet were measured. There were greater varietal differences in leaf movement, leaf temperature and transpiration rate. Leaf temperature seemed to be adjusted by leaf movement and transpiration. The extent to which is adjusted by leaf movement and transpiration differed among the cultivars; leaf temperature was influenced mainly by leaf movement for Gaofei 16 and Dongnong 87 - 138, mainly by transpiration for Qindou 7232 and 8874, and by both for 8285 - 8. Intercepted radiation in the upper two layers of the canopy (20 cm from the uppermost) was greater in the irrigated plot, although the mean values of total leaflets of the irrigated plot were not different as compared to the non-irrigated plot. Although paraheliotropic leaf movement decreased radiation interception, it offers some possibilities for the improvement in radiation penetration within a dense canopy. Cumulated amount of transpiration during a day was compared between the restrained-leaf and the non-leaf-restrained plants in 8874. Paraheliotropic leaf movement reduced water loss by 23% in the irrigated and 71% in the non-irrigated plots

In vivo microdialysis studies on the effects of decortication and excitotoxic lesions on kainic acid-induced calcium fluxes, and endogenous amino acid release, in the rat striatum

Energy Technology Data Exchange (ETDEWEB)

Butcher, S.P.; Lazarewicz, J.W.; Hamberger, A.

1987-11-01

The in vivo effects of kainate (1 mM) on fluxes of /sup 45/Ca2+, and endogenous amino acids, were examined in the rat striatum using the brain microdialysis technique. Kainate evoked a rapid decrease in dialysate /sup 45/Ca2+, and an increase in the concentration of amino acids in dialysates in Ca2+-free dialysates. Taurine was elevated six- to 10-fold, glutamate two- to threefold, and aspartate 1.5- to twofold. There was also a delayed increase in phosphoethanolamine, whereas nonneuroactive amino acids were increased only slightly. The kainic acid-evoked reduction in dialysate /sup 45/Ca2+ activity was attenuated in striata lesioned previously with kainate, suggesting the involvement of intrinsic striatal neurons in this response. The increase in taurine concentration induced by kainate was slightly smaller under these conditions. Decortication did not affect the kainate-evoked alterations in either dialysate /sup 45/Ca2+ or amino acids. These data suggest that kainate does not release acidic amino acids from their transmitter pools located in corticostriatal terminals.

Rapid, high-resolution measurement of leaf area and leaf orientation using terrestrial LiDAR scanning data

International Nuclear Information System (INIS)

Bailey, Brian N; Mahaffee, Walter F

2017-01-01

The rapid evolution of high performance computing technology has allowed for the development of extremely detailed models of the urban and natural environment. Although models can now represent sub-meter-scale variability in environmental geometry, model users are often unable to specify the geometry of real domains at this scale given available measurements. An emerging technology in this field has been the use of terrestrial LiDAR scanning data to rapidly measure the three-dimensional geometry of trees, such as the distribution of leaf area. However, current LiDAR methods suffer from the limitation that they require detailed knowledge of leaf orientation in order to translate projected leaf area into actual leaf area. Common methods for measuring leaf orientation are often tedious or inaccurate, which places constraints on the LiDAR measurement technique. This work presents a new method to simultaneously measure leaf orientation and leaf area within an arbitrarily defined volume using terrestrial LiDAR data. The novelty of the method lies in the direct measurement of the fraction of projected leaf area G from the LiDAR data which is required to relate projected leaf area to total leaf area, and in the new way in which radiation transfer theory is used to calculate leaf area from the LiDAR data. The method was validated by comparing LiDAR-measured leaf area to (1) ‘synthetic’ or computer-generated LiDAR data where the exact area was known, and (2) direct measurements of leaf area in the field using destructive sampling. Overall, agreement between the LiDAR and reference measurements was very good, showing a normalized root-mean-squared-error of about 15% for the synthetic tests, and 13% in the field. (paper)

Leaf endophyte load influences fungal garden development in leaf-cutting ants

Directory of Open Access Journals (Sweden)

Van Bael Sunshine A

2012-11-01

Full Text Available Abstract Background Previous work has shown that leaf-cutting ants prefer to cut leaf material with relatively low fungal endophyte content. This preference suggests that fungal endophytes exact a cost on the ants or on the development of their colonies. We hypothesized that endophytes may play a role in their host plants’ defense against leaf-cutting ants. To measure the long-term cost to the ant colony of fungal endophytes in their forage material, we conducted a 20-week laboratory experiment to measure fungal garden development for colonies that foraged on leaves with low or high endophyte content. Results Colony mass and the fungal garden dry mass did not differ significantly between the low and high endophyte feeding treatments. There was, however, a marginally significant trend toward greater mass of fungal garden per ant worker in the low relative to the high endophyte treatment. This trend was driven by differences in the fungal garden mass per worker from the earliest samples, when leaf-cutting ants had been foraging on low or high endophyte leaf material for only 2 weeks. At two weeks of foraging, the mean fungal garden mass per worker was 77% greater for colonies foraging on leaves with low relative to high endophyte loads. Conclusions Our data suggest that the cost of endophyte presence in ant forage material may be greatest to fungal colony development in its earliest stages, when there are few workers available to forage and to clean leaf material. This coincides with a period of high mortality for incipient colonies in the field. We discuss how the endophyte-leaf-cutter ant interaction may parallel constitutive defenses in plants, whereby endophytes reduce the rate of colony development when its risk of mortality is greatest.

Easy Leaf Area: Automated Digital Image Analysis for Rapid and Accurate Measurement of Leaf Area

Directory of Open Access Journals (Sweden)

Hsien Ming Easlon

2014-07-01

Full Text Available Premise of the study: Measurement of leaf areas from digital photographs has traditionally required significant user input unless backgrounds are carefully masked. Easy Leaf Area was developed to batch process hundreds of Arabidopsis rosette images in minutes, removing background artifacts and saving results to a spreadsheet-ready CSV file. Methods and Results: Easy Leaf Area uses the color ratios of each pixel to distinguish leaves and calibration areas from their background and compares leaf pixel counts to a red calibration area to eliminate the need for camera distance calculations or manual ruler scale measurement that other software methods typically require. Leaf areas estimated by this software from images taken with a camera phone were more accurate than ImageJ estimates from flatbed scanner images. Conclusions: Easy Leaf Area provides an easy-to-use method for rapid measurement of leaf area and nondestructive estimation of canopy area from digital images.

Automated Leaf Tracking using Multi-view Image Sequences of Maize Plants for Leaf-growth Monitoring

Science.gov (United States)

Das Choudhury, S.; Awada, T.; Samal, A.; Stoerger, V.; Bashyam, S.

2017-12-01

Extraction of phenotypes with botanical importance by analyzing plant image sequences has the desirable advantages of non-destructive temporal phenotypic measurements of a large number of plants with little or no manual intervention in a relatively short period of time. The health of a plant is best interpreted by the emergence timing and temporal growth of individual leaves. For automated leaf growth monitoring, it is essential to track each leaf throughout the life cycle of the plant. Plants are constantly changing organisms with increasing complexity in architecture due to variations in self-occlusions and phyllotaxy, i.e., arrangements of leaves around the stem. The leaf cross-overs pose challenges to accurately track each leaf using single view image sequence. Thus, we introduce a novel automated leaf tracking algorithm using a graph theoretic approach by multi-view image sequence analysis based on the determination of leaf-tips and leaf-junctions in the 3D space. The basis of the leaf tracking algorithm is: the leaves emerge using bottom-up approach in the case of a maize plant, and the direction of leaf emergence strictly alternates in terms of direction. The algorithm involves labeling of the individual parts of a plant, i.e., leaves and stem, following graphical representation of the plant skeleton, i.e., one-pixel wide connected line obtained from the binary image. The length of the leaf is measured by the number of pixels in the leaf skeleton. To evaluate the performance of the algorithm, a benchmark dataset is indispensable. Thus, we publicly release University of Nebraska-Lincoln Component Plant Phenotyping dataset-2 (UNL-CPPD-2) consisting of images of the 20 maize plants captured by visible light camera of the Lemnatec Scanalyzer 3D high throughout plant phenotyping facility once daily for 60 days from 10 different views. The dataset is aimed to facilitate the development and evaluation of leaf tracking algorithms and their uniform comparisons.

Measurement for the MLC leaf velocity profile by considering the leaf leakage using a radiographic film

International Nuclear Information System (INIS)

Chow, James C L; Grigorov, Grigor N

2006-01-01

A method to measure the velocity profile of a multi-leaf collimator (MLC) leaf along its travel range using a radiographic film is reported by considering the intra-leaf leakage. A specific dynamic MLC field with leaves travelling from the field edge to the isocentre line was designed. The field was used to expose a radiographic film, which was then scanned, and the dose profile along the horizontal leaf axis was measured. The velocity at a sampling point on the film can be calculated by considering the horizontal distance between the sampling point and the isocentre line, dose at the sampling point, dose rate of the linear accelerator, the total leaf travel time from the field edge to isocentre line and the pre-measured dose rate of leaf leakage. With the leaf velocities and velocity profiles for all MLC leaves measured routinely, a comprehensive and simple QA for the MLC can be set up to test the consistency of the leaf velocity performance which is essential to the IMRT delivery using a sliding window technique. (note)

Geometric leaf placement strategies

International Nuclear Information System (INIS)

Fenwick, J D; Temple, S W P; Clements, R W; Lawrence, G P; Mayles, H M O; Mayles, W P M

2004-01-01

Geometric leaf placement strategies for multileaf collimators (MLCs) typically involve the expansion of the beam's-eye-view contour of a target by a uniform MLC margin, followed by movement of the leaves until some point on each leaf end touches the expanded contour. Film-based dose-distribution measurements have been made to determine appropriate MLC margins-characterized through an index d 90 -for multileaves set using one particular strategy to straight lines lying at various angles to the direction of leaf travel. Simple trigonometric relationships exist between different geometric leaf placement strategies and are used to generalize the results of the film work into d 90 values for several different strategies. Measured d 90 values vary both with angle and leaf placement strategy. A model has been derived that explains and describes quite well the observed variations of d 90 with angle. The d 90 angular variations of the strategies studied differ substantially, and geometric and dosimetric reasoning suggests that the best strategy is the one with the least angular variation. Using this criterion, the best straightforwardly implementable strategy studied is a 'touch circle' approach for which semicircles are imagined to be inscribed within leaf ends, the leaves being moved until the semicircles just touch the expanded target outline

Apparent over-investment in leaf venation relaxes leaf morphological constraints on photosynthesis in arid habitats

Science.gov (United States)

de Boer, Hugo; Drake, Paul; Veneklaas, Erik

2017-04-01

The close relationship between leaf water status and stomatal conductance implies that the hydraulic architecture of leaves poses an important constraint on transpiration, specifically in arid environments with high evaporative demands. However, it remains uncertain how morphological, hydraulic and photosynthetic traits are coordinated to achieve optimal leaf functioning in arid environments. Critical is that leaf veins supply the mesophyll with water that evaporates when stomata are open to allow CO2 uptake for photosynthesis. Theoretical analyses suggest that water is optimally distributed in the mesophyll when the lateral distance between veins (dx) is equal to the distance from these veins to the epidermis (dy), expressed as dx:dy≈1. Although this theory is supported by observations on many derived angiosperms, we hypothesize that plants in arid environments may reduce dx:dy below unity owing to climate-specific functional adaptations of increased leaf thickness and increased vein density. To test our hypothesis we assembled leaf hydraulic, morphological and photosynthetic traits of 68 species from the Eucalyptus and Corymbia genera (termed eucalypts) along an aridity gradient in southwestern Australia. We inferred the potential gas exchange advantage of reducing dx beyond dy using a model that links leaf morphology and hydraulics to photosynthesis. Our observations reveal that eucalypts in arid environments have thick amphistomatous leaves with high vein densities, resulting in dx:dy ratios that range from 1.6 to 0.15 along the aridity gradient. Our model suggests that as leaves become thicker, the effect of reducing dx beyond dy is to offset the reduction in leaf gas exchange that would result from maintaining dx:dy at unity. This apparent over-investment in leaf venation may be explained from the selective pressure of aridity, under which traits associated with long leaf lifespan, high hydraulic and thermal capacitances, and high potential rates of leaf

NARROW LEAF 7 controls leaf shape mediated by auxin in rice

NARCIS (Netherlands)

Fujino, Kenji; Matsuda, Yasuyuki; Ozawa, Kenjirou; Nishimura, Takeshi; Koshiba, Tomokazu; Fraaije, Marco W.; Sekiguchi, Hiroshi

Elucidation of the genetic basis of the control of leaf shape could be of use in the manipulation of crop traits, leading to more stable and increased crop production. To improve our understanding of the process controlling leaf shape, we identified a mutant gene in rice that causes a significant

Scaling up stomatal conductance from leaf to canopy using a dual-leaf model for estimating crop evapotranspiration.

Directory of Open Access Journals (Sweden)

Risheng Ding

Full Text Available The dual-source Shuttleworth-Wallace model has been widely used to estimate and partition crop evapotranspiration (λET. Canopy stomatal conductance (Gsc, an essential parameter of the model, is often calculated by scaling up leaf stomatal conductance, considering the canopy as one single leaf in a so-called "big-leaf" model. However, Gsc can be overestimated or underestimated depending on leaf area index level in the big-leaf model, due to a non-linear stomatal response to light. A dual-leaf model, scaling up Gsc from leaf to canopy, was developed in this study. The non-linear stomata-light relationship was incorporated by dividing the canopy into sunlit and shaded fractions and calculating each fraction separately according to absorbed irradiances. The model includes: (1 the absorbed irradiance, determined by separately integrating the sunlit and shaded leaves with consideration of both beam and diffuse radiation; (2 leaf area for the sunlit and shaded fractions; and (3 a leaf conductance model that accounts for the response of stomata to PAR, vapor pressure deficit and available soil water. In contrast to the significant errors of Gsc in the big-leaf model, the predicted Gsc using the dual-leaf model had a high degree of data-model agreement; the slope of the linear regression between daytime predictions and measurements was 1.01 (R2 = 0.98, with RMSE of 0.6120 mm s-1 for four clear-sky days in different growth stages. The estimates of half-hourly λET using the dual-source dual-leaf model (DSDL agreed well with measurements and the error was within 5% during two growing seasons of maize with differing hydrometeorological and management strategies. Moreover, the estimates of soil evaporation using the DSDL model closely matched actual measurements. Our results indicate that the DSDL model can produce more accurate estimation of Gsc and λET, compared to the big-leaf model, and thus is an effective alternative approach for estimating and

Seasonality of Leaf Carbon Isotopic Composition and Leaf Water Isotopic Enrichment in a Mixed Evergreen Forest in Southern California

Science.gov (United States)

Santiago, L. S.; Sickman, J. O.; Goulden, M.; DeVan, C.; Pasquini, S. C.; Pivovaroff, A. L.

2011-12-01

Leaf carbon isotopic composition and leaf water isotopic enrichment reflect physiological processes and are important for linking local and regional scale processes to global patterns. We investigated how seasonality affects the isotopic composition of bulk leaf carbon, leaf sugar carbon, and leaf water hydrogen under a Mediterranean climate. Leaf and stem samples were collected monthly from four tree species (Calocedrus decurrens, Pinus lambertiana, Pinus ponderosa, and Quercus chrysolepis) at the James San Jacinto Mountain Reserve in southern California. Mean monthly bulk leaf carbon isotopic composition varied from -34.5 % in P. ponderosa to -24.7 % in P. lambertiana and became more depleted in 13C from the spring to the summer. Mean monthly leaf sugar varied from -29.3 % in P. ponderosa to -21.8 % in P. lambertiana and was enriched in 13C during the winter, spring and autumn, but depleted during the mid-summer. Leaf water hydrogen isotopic composition was 28.4 to 68.8 % more enriched in deuterium than source water and this enrichment was greater as seasonal drought progressed. These data indicate that leaf carbon and leaf water hydrogen isotopic composition provide sensitive measures that connect plant physiological processes to short-term climatic variability.

Leaf sequencing algorithms for segmented multileaf collimation

International Nuclear Information System (INIS)

Kamath, Srijit; Sahni, Sartaj; Li, Jonathan; Palta, Jatinder; Ranka, Sanjay

2003-01-01

The delivery of intensity-modulated radiation therapy (IMRT) with a multileaf collimator (MLC) requires the conversion of a radiation fluence map into a leaf sequence file that controls the movement of the MLC during radiation delivery. It is imperative that the fluence map delivered using the leaf sequence file is as close as possible to the fluence map generated by the dose optimization algorithm, while satisfying hardware constraints of the delivery system. Optimization of the leaf sequencing algorithm has been the subject of several recent investigations. In this work, we present a systematic study of the optimization of leaf sequencing algorithms for segmental multileaf collimator beam delivery and provide rigorous mathematical proofs of optimized leaf sequence settings in terms of monitor unit (MU) efficiency under most common leaf movement constraints that include minimum leaf separation constraint and leaf interdigitation constraint. Our analytical analysis shows that leaf sequencing based on unidirectional movement of the MLC leaves is as MU efficient as bidirectional movement of the MLC leaves

Leaf sequencing algorithms for segmented multileaf collimation

Energy Technology Data Exchange (ETDEWEB)

Kamath, Srijit [Department of Computer and Information Science and Engineering, University of Florida, Gainesville, FL (United States); Sahni, Sartaj [Department of Computer and Information Science and Engineering, University of Florida, Gainesville, FL (United States); Li, Jonathan [Department of Radiation Oncology, University of Florida, Gainesville, FL (United States); Palta, Jatinder [Department of Radiation Oncology, University of Florida, Gainesville, FL (United States); Ranka, Sanjay [Department of Computer and Information Science and Engineering, University of Florida, Gainesville, FL (United States)

2003-02-07

The delivery of intensity-modulated radiation therapy (IMRT) with a multileaf collimator (MLC) requires the conversion of a radiation fluence map into a leaf sequence file that controls the movement of the MLC during radiation delivery. It is imperative that the fluence map delivered using the leaf sequence file is as close as possible to the fluence map generated by the dose optimization algorithm, while satisfying hardware constraints of the delivery system. Optimization of the leaf sequencing algorithm has been the subject of several recent investigations. In this work, we present a systematic study of the optimization of leaf sequencing algorithms for segmental multileaf collimator beam delivery and provide rigorous mathematical proofs of optimized leaf sequence settings in terms of monitor unit (MU) efficiency under most common leaf movement constraints that include minimum leaf separation constraint and leaf interdigitation constraint. Our analytical analysis shows that leaf sequencing based on unidirectional movement of the MLC leaves is as MU efficient as bidirectional movement of the MLC leaves.

Study on creation of an indocalamus leaf flavor

Directory of Open Access Journals (Sweden)

Guangyong ZHU

2015-01-01

Full Text Available AbstractFlavors represent a small but significant segment of food industry. Sensory characteristics play an important role in the process of consumer acceptance and preference. Indocalamus leaf takes on a pleasant odor and indocalamus leaf flavor can be used in many products. However, indocalamus leaf flavor formula has not been reported. Therefore, developing an indocalamus leaf flavor is of significant interests. Note is a distinct flavor or odor characteristic. This paper concentrates on preparation and creation of indocalamus leaf flavor according to the notes of indocalamus leaf. The notes were obtained by smelling indocalamus leaf, and the results showed that the notes of indocalamus leaf flavor can be classified as: green-leafy note, sweet note, beany note, aldehydic note, waxy note, woody note, roast note, creamy note, and nutty note. According to the notes of indocalamus leaf odor, a typical indocalamus leaf flavor formula was obtained. The indocalamus leaf flavor blended is pleasant, harmonious, and has characteristics of indocalamus leaf odor.

The dosimetric impact of leaf interdigitation and leaf width on VMAT treatment planning in Pinnacle: comparing Pareto fronts

International Nuclear Information System (INIS)

Van Kesteren, Z; Janssen, T M; Damen, E; Van Vliet-Vroegindeweij, C

2012-01-01

To evaluate in an objective way the effect of leaf interdigitation and leaf width on volumetric modulated arc therapy plans in Pinnacle. Three multileaf collimators (MLCs) were modeled: two 10 mm leaf width MLCs, with and without interdigitating leafs, and a 5 mm leaf width MLC with interdigitating leafs. Three rectum patients and three prostate patients were used for the planning study. In order to compare treatment techniques in an objective way, a Pareto front comparison was carried out. 200 plans were generated in an automated way, per patient per MLC model, resulting in a total of 3600 plans. From these plans, Pareto-optimal plans were selected which were evaluated for various dosimetric variables. The capability of leaf interdigitation showed little dosimetric impact on the treatment plans, when comparing the 10 mm leaf width MLC with and without leaf interdigitation. When comparing the 10 mm leaf width MLC with the 5 mm leaf width MLC, both with interdigitating leafs, improvement in plan quality was observed. For both patient groups, the integral dose was reduced by 0.6 J for the thin MLC. For the prostate patients, the mean dose to the anal sphincter was reduced by 1.8 Gy and the conformity of the V 95% was reduced by 0.02 using the thin MLC. The V 65% of the rectum was reduced by 0.1% and the dose homogeneity with 1.5%. For rectum patients, the mean dose to the bowel was reduced by 1.4 Gy and the mean dose to the bladder with 0.8 Gy for the thin MLC. The conformity of the V 95% was equivalent for the 10 and 5 mm leaf width MLCs for the rectum patients. We have objectively compared three types of MLCs in a planning study for prostate and rectum patients by analyzing Pareto-optimal plans which were generated in an automated way. Interdigitation of MLC leafs does not generate better plans using the SmartArc algorithm in Pinnacle. Changing the MLC leaf width from 10 to 5 mm generates better treatment plans although the clinical relevance remains to be proven

The dosimetric impact of leaf interdigitation and leaf width on VMAT treatment planning in Pinnacle: comparing Pareto fronts.

Science.gov (United States)

van Kesteren, Z; Janssen, T M; Damen, E; van Vliet-Vroegindeweij, C

2012-05-21

To evaluate in an objective way the effect of leaf interdigitation and leaf width on volumetric modulated arc therapy plans in Pinnacle. Three multileaf collimators (MLCs) were modeled: two 10 mm leaf width MLCs, with and without interdigitating leafs, and a 5 mm leaf width MLC with interdigitating leafs. Three rectum patients and three prostate patients were used for the planning study. In order to compare treatment techniques in an objective way, a Pareto front comparison was carried out. 200 plans were generated in an automated way, per patient per MLC model, resulting in a total of 3600 plans. From these plans, Pareto-optimal plans were selected which were evaluated for various dosimetric variables. The capability of leaf interdigitation showed little dosimetric impact on the treatment plans, when comparing the 10 mm leaf width MLC with and without leaf interdigitation. When comparing the 10 mm leaf width MLC with the 5 mm leaf width MLC, both with interdigitating leafs, improvement in plan quality was observed. For both patient groups, the integral dose was reduced by 0.6 J for the thin MLC. For the prostate patients, the mean dose to the anal sphincter was reduced by 1.8 Gy and the conformity of the V(95%) was reduced by 0.02 using the thin MLC. The V(65%) of the rectum was reduced by 0.1% and the dose homogeneity with 1.5%. For rectum patients, the mean dose to the bowel was reduced by 1.4 Gy and the mean dose to the bladder with 0.8 Gy for the thin MLC. The conformity of the V(95%) was equivalent for the 10 and 5 mm leaf width MLCs for the rectum patients. We have objectively compared three types of MLCs in a planning study for prostate and rectum patients by analyzing Pareto-optimal plans which were generated in an automated way. Interdigitation of MLC leafs does not generate better plans using the SmartArc algorithm in Pinnacle. Changing the MLC leaf width from 10 to 5 mm generates better treatment plans although the clinical relevance remains

DIFFERENCES IN LEAF GAS EXCHANGE AND LEAF CHARACTERISTICS BETWEEN TWO ALMOND CULTIVARS

Directory of Open Access Journals (Sweden)

George D. Nanos

2013-12-01

Full Text Available Leaf chlorophyll content, specific leaf weight (SLW, photosynthetic and transpiration rates, stomatal functioning, water use efficiency and quantum yield were assessed during the kernel filling period for two consecutive years in order to understand tissue-centered physiological profile differences between two commercial almond cultivars, ‘Ferragnès’ and ‘Texas’. Similar SLWs were observed on the studied cultivars; however, chlorophyll content, net photosynthetic and transpiration rates and stomatal functioning demonstrated statistically significant differences. In both cultivars, an overall decline in the examined parameters towards fruit maturation (i.e. end of the summer was recorded. ‘Ferragnès’ leaves were found to be more efficient in leaf photosynthesis related performance during kernel filling, when irrigated sufficiently, in comparison to ‘Texas’ leaves. Low average values of leaf conductance during summer in ‘Texas’ leaves revealed its potential for adaptation in cool climates and increased carbon assimilation therein for high kernel yield.

Estimating leaf functional traits by inversion of PROSPECT: Assessing leaf dry matter content and specific leaf area in mixed mountainous forest

Science.gov (United States)

Ali, Abebe Mohammed; Darvishzadeh, Roshanak; Skidmore, Andrew K.; Duren, Iris van; Heiden, Uta; Heurich, Marco

2016-03-01

Assessments of ecosystem functioning rely heavily on quantification of vegetation properties. The search is on for methods that produce reliable and accurate baseline information on plant functional traits. In this study, the inversion of the PROSPECT radiative transfer model was used to estimate two functional leaf traits: leaf dry matter content (LDMC) and specific leaf area (SLA). Inversion of PROSPECT usually aims at quantifying its direct input parameters. This is the first time the technique has been used to indirectly model LDMC and SLA. Biophysical parameters of 137 leaf samples were measured in July 2013 in the Bavarian Forest National Park, Germany. Spectra of the leaf samples were measured using an ASD FieldSpec3 equipped with an integrating sphere. PROSPECT was inverted using a look-up table (LUT) approach. The LUTs were generated with and without using prior information. The effect of incorporating prior information on the retrieval accuracy was studied before and after stratifying the samples into broadleaf and conifer categories. The estimated values were evaluated using R2 and normalized root mean square error (nRMSE). Among the retrieved variables the lowest nRMSE (0.0899) was observed for LDMC. For both traits higher R2 values (0.83 for LDMC and 0.89 for SLA) were discovered in the pooled samples. The use of prior information improved accuracy of the retrieved traits. The strong correlation between the estimated traits and the NIR/SWIR region of the electromagnetic spectrum suggests that these leaf traits could be assessed at canopy level by using remotely sensed data.

Spectral reflectance relationships to leaf water stress

Science.gov (United States)

Ripple, William J.

1986-01-01

Spectral reflectance data were collected from detached snapbean leaves in the laboratory with a multiband radiometer. Four experiments were designed to study the spectral response resulting from changes in leaf cover, relative water content of leaves, and leaf water potential. Spectral regions included in the analysis were red (630-690 nm), NIR (760-900 nm), and mid-IR (2.08-2.35 microns). The red and mid-IR bands showed sensitivity to changes in both leaf cover and relative water content of leaves. The NIR was only highly sensitive to changes in leaf cover. Results provided evidence that mid-IR reflectance was governed primarily by leaf moisture content, although soil reflectance was an important factor when leaf cover was less than 100 percent. High correlations between leaf water potentials and reflectance were attributed to covariances with relative water content of leaves and leaf cover.

Comparison of leaf-on and leaf-off ALS data for mapping riparian tree species

Science.gov (United States)

Laslier, Marianne; Ba, Antoine; Hubert-Moy, Laurence; Dufour, Simon

2017-10-01

Forest species composition is a fundamental indicator of forest study and management. However, describing forest species composition at large scales and of highly diverse populations remains an issue for which remote sensing can provide significant contribution, in particular, Airborne Laser Scanning (ALS) data. Riparian corridors are good examples of highly valuable ecosystems, with high species richness and large surface areas that can be time consuming and expensive to monitor with in situ measurements. Remote sensing could be useful to study them, but few studies have focused on monitoring riparian tree species using ALS data. This study aimed to determine which metrics derived from ALS data are best suited to identify and map riparian tree species. We acquired very high density leaf-on and leaf-off ALS data along the Sélune River (France). In addition, we inventoried eight main riparian deciduous tree species along the study site. After manual segmentation of the inventoried trees, we extracted 68 morphological and structural metrics from both leaf-on and leaf-off ALS point clouds. Some of these metrics were then selected using Sequential Forward Selection (SFS) algorithm. Support Vector Machine (SVM) classification results showed good accuracy with 7 metrics (0.77). Both leaf-on and leafoff metrics were kept as important metrics for distinguishing tree species. Results demonstrate the ability of 3D information derived from high density ALS data to identify riparian tree species using external and internal structural metrics. They also highlight the complementarity of leaf-on and leaf-off Lidar data for distinguishing riparian tree species.

Influence of hydrothermal processing on functional properties and grain morphology of finger millet.

Science.gov (United States)

Dharmaraj, Usha; Meera, M S; Reddy, S Yella; Malleshi, Nagappa G

2015-03-01

Finger millet was hydrothermally processed followed by decortication. Changes in color, diameter, density, sphericity, thermal and textural characteristics and also some of the functional properties of the millet along with the grain morphology of the kernels after hydrothermal processing and decortication were studied. It was observed that, the millet turned dark after hydrothermal processing and color improved over native millet after decortication. A slight decrease in grain diameter was observed but sphericity of the grains increased on decortication. The soft and fragile endosperm turned into a hard texture and grain hardness increased by about 6 fold. Hydrothermal processing increased solubility and swelling power of the millet at ambient temperature. Pasting profile indicated that, peak viscosity decreased significantly on hydrothermal processing and both hydrothermally processed and decorticated millet exhibited zero breakdown viscosity. Enthalpy was negative for hydrothermally processed millet and positive for decorticated grains. Microscopic studies revealed that the orderly structure of endosperm changed to a coherent mass after hydrothermal processing and the different layers of seed coat get fused with the endosperm.

Specific leaf area estimation from leaf and canopy reflectance through optimization and validation of vegetation indices

NARCIS (Netherlands)

Ali, A.M.; Darvishzadeh, R.; Skidmore, A.K.; van Duren, I.C.

2017-01-01

Specific leaf area (SLA), which is defined as the leaf area per unit of dry leaf mass is an important component when assessing functional diversity and plays a key role in ecosystem modeling, linking plant carbon and water cycles as well as quantifying plant physiological processes. However, studies

Leaf hydraulic conductance declines in coordination with photosynthesis, transpiration and leaf water status as soybean leaves age regardless of soil moisture

Science.gov (United States)

Locke, Anna M.; Ort, Donald R.

2014-01-01

Photosynthesis requires sufficient water transport through leaves for stomata to remain open as water transpires from the leaf, allowing CO2 to diffuse into the leaf. The leaf water needs of soybean change over time because of large microenvironment changes over their lifespan, as leaves mature in full sun at the top of the canopy and then become progressively shaded by younger leaves developing above. Leaf hydraulic conductance (K leaf), a measure of the leaf’s water transport capacity, can often be linked to changes in microenvironment and transpiration demand. In this study, we tested the hypothesis that K leaf would decline in coordination with transpiration demand as soybean leaves matured and aged. Photosynthesis (A), stomatal conductance (g s) and leaf water potential (Ψleaf) were also measured at various leaf ages with both field- and chamber-grown soybeans to assess transpiration demand. K leaf was found to decrease as soybean leaves aged from maturity to shading to senescence, and this decrease was strongly correlated with midday A. Decreases in K leaf were further correlated with decreases in g s, although the relationship was not as strong as that with A. Separate experiments investigating the response of K leaf to drought demonstrated no acclimation of K leaf to drought conditions to protect against cavitation or loss of g s during drought and confirmed the effect of leaf age in K leaf observed in the field. These results suggest that the decline of leaf hydraulic conductance as leaves age keeps hydraulic supply in balance with demand without K leaf becoming limiting to transpiration water flux. PMID:25281701

Seagrass leaf element content

NARCIS (Netherlands)

Vonk, J.A.; Smulders, Fee O.H.; Christianen, Marjolijn J.A.; Govers, Laura L.

2017-01-01

Knowledge on the role of seagrass leaf elements and in particular micronutrients and their ranges is limited. We present a global database, consisting of 1126 unique leaf values for ten elements, obtained from literature and unpublished data, spanning 25 different seagrass species from 28 countries.

Estimating leaf area and leaf biomass of open-grown deciduous urban trees

Science.gov (United States)

David J. Nowak

1996-01-01

Logarithmic regression equations were developed to predict leaf area and leaf biomass for open-grown deciduous urban trees based on stem diameter and crown parameters. Equations based on crown parameters produced more reliable estimates. The equations can be used to help quantify forest structure and functions, particularly in urbanizing and urban/suburban areas.

Prophylactic effect of paw-paw leaf and bitter leaf extracts on the ...

African Journals Online (AJOL)

STORAGESEVER

2008-08-18

Aug 18, 2008 ... (ANOVA) and significant means separated using FLSD = LSD procedure as outlined in Obi (2002). RESULTS AND DISCUSSION. In pre-soaking, paw-paw leaf (PL) extract had no significant effect (P > 0.05) on the disease incidence at. 50% anthesis. Bitter leaf (BL) extract had a high signifi- cant effect (P ...

Joint Leaf chlorophyll and leaf area index retrieval from Landsat data using a regularized model inversion system

Science.gov (United States)

Leaf area index (LAI) and leaf chlorophyll (Chl) content represent key biophysical and biochemical controls on water, energy and carbon exchange processes in the terrestrial biosphere. In combination, LAI and leaf Chl content provide critical information on vegetation density, vitality and photosynt...

Using Leaf Samples to Establish a Library of Tropical Leaf Fingerprints

Science.gov (United States)

Ngo, P.; Nguyen, R.; Anderson, C.; Weiss, P.

2010-12-01

Variation in leaf chemistry is directly expressed in spectroscopic patterns of tropical canopies. The goal of the Spectranomics project is to explore this variation in the hopes of developing a method to measure tropical forest diversity remotely from airborne or space-bound spectroscopy in the future. We analyzed tomato leaves for various chemical compositions to better understand the Spectranomics approach to quantifying chemical data of tropical species. We also compared our data to standard data in each analysis. Our results allow us to give the tomato leaves a chemical signature in which we are able to use to compare to other leaf samples. Using this process, we are able to create a library of leaf signatures and document the variety of tree species in tropical forests around the world.

Leaf density explains variation in leaf mass per area in rice between cultivars and nitrogen treatments.

Science.gov (United States)

Xiong, Dongliang; Wang, Dan; Liu, Xi; Peng, Shaobing; Huang, Jianliang; Li, Yong

2016-05-01

Leaf mass per area (LMA) is an important leaf trait; however, correlations between LMA and leaf anatomical features and photosynthesis have not been fully investigated, especially in cereal crops. The objectives of this study were (a) to investigate the correlations between LMA and leaf anatomical traits; and (b) to clarify the response of LMA to nitrogen supply and its effect on photosynthetic nitrogen use efficiency (PNUE). In the present study, 11 rice varieties were pot grown under sufficient nitrogen (SN) conditions, and four selected rice cultivars were grown under low nitrogen (LN) conditions. Leaf anatomical traits, gas exchange and leaf N content were measured. There was large variation in LMA across selected rice varieties. Regression analysis showed that the variation in LMA was more closely related to leaf density (LD) than to leaf thickness (LT). LMA was positively related to the percentage of mesophyll tissue area (%mesophyll), negatively related to the percentage of epidermis tissue area (%epidermis) and unrelated to the percentage of vascular tissue area (%vascular). The response of LMA to N supplementation was dependent on the variety and was also mainly determined by the response of LD to N. Compared with SN, photosynthesis was significantly decreased under LN, while PNUE was increased. The increase in PNUE was more critical in rice cultivars with a higher LMA under SN supply. Leaf density is the major cause of the variation in LMA across rice varieties and N treatments, and an increase in LMA under high N conditions would aggravate the decrease in PNUE. © The Author 2016. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

7 CFR 30.2 - Leaf tobacco.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf tobacco. 30.2 Section 30.2 Agriculture... Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER REGULATIONS TOBACCO STOCKS AND STANDARDS Classification of Leaf Tobacco Covering Classes, Types and Groups of Grades § 30.2 Leaf...

7 CFR 29.3035 - Leaf structure.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf structure. 29.3035 Section 29.3035 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Leaf structure. The cell development of a leaf as indicated by its porosity or solidity. (See Elements...

7 CFR 29.3526 - Leaf scrap.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.3526 Section 29.3526 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 95) § 29.3526 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling...

7 CFR 29.3034 - Leaf scrap.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.3034 Section 29.3034 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Leaf scrap. A by-product of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and...

7 CFR 29.6022 - Leaf scrap.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.6022 Section 29.6022 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Definitions § 29.6022 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results...

Infrared remote sensing for canopy temperature in paddy field and relationship between leaf temperature and leaf color

International Nuclear Information System (INIS)

Wakiyama, Y.

2002-01-01

Infrared remote sensing is used for crop monitoring, for example evaluation of water stress, detection of infected crops and estimation of transpiration and photosynthetic rates. This study was conducted to show another application of remote sensing information. The relationship between rice leaf temperature and chlorophyll content in the leaf blade was investigated by using thermography during the ripening period. The canopy of a rice community fertilized by top dressing was cooler than that not fertilized in a 1999 field experiment. In an experiment using thermocouples to measure leaf temperature, a rice leaf with high chlorophyll content was also cooler than that with a low chlorophyll content. Transpiration resistance and transpiration rate were measured with a porometer. Transpiration rate was higher with increasing chlorophyll content in the leaf blade. Stomatal aperture is related to chlorophyll content in the leaf blade. High degree of stomatal aperture is caused by high chlorophyll content in the leaf blade. As degree of stomatal aperture increases, transpiration rate increases. Therefore the rice leaf got cooler with increasing chlorophyll content in leaf blade. Paddy rice communities with different chlorophyll contents were provided with fertilization of different nitrogen levels on basal and top dressing in a 2000 field experiment. Canopy temperature of the rice community with high chlorophyll content was 0.85°C cooler than that of the rice community with low chlorophyll content. Results of this study revealed that infrared remote sensing could detect difference in chlorophyll contents in rice communities and could be used in fertilizer management in paddy fields. (author)

An analytical approach for optimizing the leaf design of a multi-leaf collimator in a linear accelerator

International Nuclear Information System (INIS)

Topolnjak, R; Heide, U A van der

2008-01-01

In this study, we present an analytical approach for optimizing the leaf design of a multi-leaf collimator (MLC) in a linear accelerator. Because leaf designs vary between vendors, our goal is to characterize and quantify the effects of different compromises which have to be made between performance parameters. Subsequently, an optimal leaf design for an earlier proposed six-bank MLC which combines a high-resolution field-shaping ability with a large field size is determined. To this end a model of the linac is created that includes the following parameters: the source size, the maximum field size, the distance between source and isocenter, and the leaf's design parameters. First, the optimal radius of the leaf tip was found. This optimum was defined by the requirement that the fluence intensity should fall from 80% of the maximum value to 20% in a minimal distance, defining the width of the fluence penumbra. A second requirement was that this penumbra width should be constant when a leaf moves from one side of the field to the other. The geometric, transmission and total penumbra width (80-20%) were calculated depending on the design parameters. The analytical model is in agreement with Elekta, Varian and Siemens collimator designs. For leaves thinner than 4 cm, the transmission penumbra becomes dominant, and for leaves close to the source the geometric penumbra plays a role. Finally, by choosing the leaf thickness of 3.5 cm, 4 cm and 5 cm from the lowest to the highest bank, respectively, an optimal leaf design for a six-bank MLC is achieved

Apparent Overinvestment in Leaf Venation Relaxes Leaf Morphological Constraints on Photosynthesis in Arid Habitats1[OPEN

Science.gov (United States)

de Boer, Hugo J.; Drake, Paul L.; Wendt, Erin; Price, Charles A.; Schulze, Ernst-Detlef; Turner, Neil C.; Nicolle, Dean

2016-01-01

Leaf veins supply the mesophyll with water that evaporates when stomata are open to allow CO2 uptake for photosynthesis. Theoretical analyses suggest that water is optimally distributed in the mesophyll when the lateral distance between veins (dx) is equal to the distance from these veins to the epidermis (dy), expressed as dx:dy ≈ 1. Although this theory is supported by observations of many derived angiosperms, we hypothesize that plants in arid environments may reduce dx:dy below unity owing to climate-specific functional adaptations of increased leaf thickness and increased vein density. To test our hypothesis, we assembled leaf hydraulic, morphological, and photosynthetic traits of 68 species from the Eucalyptus and Corymbia genera (termed eucalypts) along an aridity gradient in southwestern Australia. We inferred the potential gas-exchange advantage of reducing dx beyond dy using a model that links leaf morphology and hydraulics to photosynthesis. Our observations reveal that eucalypts in arid environments have thick amphistomatous leaves with high vein densities, resulting in dx:dy ratios that range from 1.6 to 0.15 along the aridity gradient. Our model suggests that, as leaves become thicker, the effect of reducing dx beyond dy is to offset the reduction in leaf gas exchange that would result from maintaining dx:dy at unity. This apparent overinvestment in leaf venation may be explained from the selective pressure of aridity, under which traits associated with long leaf life span, high hydraulic and thermal capacitances, and high potential rates of leaf water transport confer a competitive advantage. PMID:27784769

7 CFR 29.6023 - Leaf structure.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf structure. 29.6023 Section 29.6023 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Definitions § 29.6023 Leaf structure. The cell development of a leaf as indicated by its...

7 CFR 29.1030 - Leaf structure.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf structure. 29.1030 Section 29.1030 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 92) § 29.1030 Leaf structure. The cell development of a leaf as indicated by its porosity. (See...

7 CFR 29.3527 - Leaf structure.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf structure. 29.3527 Section 29.3527 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 95) § 29.3527 Leaf structure. The cell development of a leaf as indicated by its porosity. (See...

Comparison of dwarf bamboos (Indocalamus sp.) leaf parameters to determine relationship between spatial density of plants and total leaf area per plant.

Science.gov (United States)

Shi, Pei-Jian; Xu, Qiang; Sandhu, Hardev S; Gielis, Johan; Ding, Yu-Long; Li, Hua-Rong; Dong, Xiao-Bo

2015-10-01

The relationship between spatial density and size of plants is an important topic in plant ecology. The self-thinning rule suggests a -3/2 power between average biomass and density or a -1/2 power between stand yield and density. However, the self-thinning rule based on total leaf area per plant and density of plants has been neglected presumably because of the lack of a method that can accurately estimate the total leaf area per plant. We aimed to find the relationship between spatial density of plants and total leaf area per plant. We also attempted to provide a novel model for accurately describing the leaf shape of bamboos. We proposed a simplified Gielis equation with only two parameters to describe the leaf shape of bamboos one model parameter represented the overall ratio of leaf width to leaf length. Using this method, we compared some leaf parameters (leaf shape, number of leaves per plant, ratio of total leaf weight to aboveground weight per plant, and total leaf area per plant) of four bamboo species of genus Indocalamus Nakai (I. pedalis (Keng) P.C. Keng, I. pumilus Q.H. Dai and C.F. Keng, I. barbatus McClure, and I. victorialis P.C. Keng). We also explored the possible correlation between spatial density and total leaf area per plant using log-linear regression. We found that the simplified Gielis equation fit the leaf shape of four bamboo species very well. Although all these four species belonged to the same genus, there were still significant differences in leaf shape. Significant differences also existed in leaf area per plant, ratio of leaf weight to aboveground weight per plant, and leaf length. In addition, we found that the total leaf area per plant decreased with increased spatial density. Therefore, we directly demonstrated the self-thinning rule to improve light interception.

NANOFIBRILLATED CELLULOSE (NFC AS A POTENTIAL REINFORCEMENT FOR HIGH PERFORMANCE CEMENT MORTAR COMPOSITES

Directory of Open Access Journals (Sweden)

Mònica Ardanuy,

2012-07-01

Full Text Available In this work, nanofibrillated cellulose (NFC has been evaluated as a potential reinforcement for cement mortar composites. Two types of vegetable fibres with different composition and properties (cellulose content and microfibrillar angle, sisal, and cotton linters pulps, were initially characterised in order to assess their reinforcing capability. Sisal pulp was found to be most suitable as reinforcement for the brittle cementitious matrix. Nanofibrillated cellulose was produced by the application of a high intensity refining process of the sisal pulp. It was found that 6 hours of refining time was required to obtain the desired nanofibrillation of the fibers. Cement mortar composites reinforced with both the sisal fibres and the nanofibrillated cellulose were prepared, and the mechanical properties were determined under flexural tests. The cement mortar composites reinforced with the nanofibrillated cellulose exhibited enhanced flexural properties, but lower values of fracture energy, than the ones reinforced with the conventional sisal fibres.

Decorticate posture

Science.gov (United States)

... 2016:chap 59. Heegaard WG, Biros MH. Head injury. In: Marx JA, Hockberger RS, Walls RM, et al, eds. Rosen's Emergency Medicine: Concepts and Clinical Practice . 8th ed. Philadelphia, PA: Elsevier ...

Transcriptional analyses of natural leaf senescence in maize.

Directory of Open Access Journals (Sweden)

Wei Yang Zhang

Full Text Available Leaf senescence is an important biological process that contributes to grain yield in crops. To study the molecular mechanisms underlying natural leaf senescence, we harvested three different developmental ear leaves of maize, mature leaves (ML, early senescent leaves (ESL, and later senescent leaves (LSL, and analyzed transcriptional changes using RNA-sequencing. Three sets of data, ESL vs. ML, LSL vs. ML, and LSL vs. ESL, were compared, respectively. In total, 4,552 genes were identified as differentially expressed. Functional classification placed these genes into 18 categories including protein metabolism, transporters, and signal transduction. At the early stage of leaf senescence, genes involved in aromatic amino acids (AAAs biosynthetic process and transport, cellular polysaccharide biosynthetic process, and the cell wall macromolecule catabolic process, were up-regulated. Whereas, genes involved in amino acid metabolism, transport, apoptosis, and response to stimulus were up-regulated at the late stage of leaf senescence. Further analyses reveals that the transport-related genes at the early stage of leaf senescence potentially take part in enzyme and amino acid transport and the genes upregulated at the late stage are involved in sugar transport, indicating nutrient recycling mainly takes place at the late stage of leaf senescence. Comparison between the data of natural leaf senescence in this study and previously reported data for Arabidopsis implies that the mechanisms of leaf senescence in maize are basically similar to those in Arabidopsis. A comparison of natural and induced leaf senescence in maize was performed. Athough many basic biological processes involved in senescence occur in both types of leaf senescence, 78.07% of differentially expressed genes in natural leaf senescence were not identifiable in induced leaf senescence, suggesting that differences in gene regulatory network may exist between these two leaf senescence

Ozone induced leaf loss and decreased leaf production of European Holly (Ilex aquifolium L.) over multiple seasons

International Nuclear Information System (INIS)

Ranford, Jonathan; Reiling, Kevin

2007-01-01

European Holly (Ilex aquifolium L.) was used to study the impact of one short (28 day) ozone fumigation episode on leaf production, leaf loss and stomatal conductance (g s ), in order to explore potential longer term effects over 3 growing seasons. Young I. aquifolium plants received an episode of either charcoal-filtered air or charcoal-filtered air with 70 nl l -1 O 3 added for 7 h d -1 over a 28 day period from June 15th 1996, then placed into ambient environment, Stoke-on-Trent, U.K. Data were collected per leaf cohort over the next three growing seasons. Ozone exposure significantly increased leaf loss and stomatal conductance and reduced leaf production over all subsequent seasons. Impact of the initial ozone stress was still detected in leaves that had no direct experimental ozone exposure. This study has shown the potential of ozone to introduce long-term phenological perturbations into ecosystems by influencing productivity over a number of seasons. - Ozone significantly alters Ilex aquifolium leaf production and loss over multiple seasons

Photoperiod-H1 (Ppd-H1) Controls Leaf Size.

Science.gov (United States)

Digel, Benedikt; Tavakol, Elahe; Verderio, Gabriele; Tondelli, Alessandro; Xu, Xin; Cattivelli, Luigi; Rossini, Laura; von Korff, Maria

2016-09-01

Leaf size is a major determinant of plant photosynthetic activity and biomass; however, it is poorly understood how leaf size is genetically controlled in cereal crop plants like barley (Hordeum vulgare). We conducted a genome-wide association scan for flowering time, leaf width, and leaf length in a diverse panel of European winter cultivars grown in the field and genotyped with a single-nucleotide polymorphism array. The genome-wide association scan identified PHOTOPERIOD-H1 (Ppd-H1) as a candidate gene underlying the major quantitative trait loci for flowering time and leaf size in the barley population. Microscopic phenotyping of three independent introgression lines confirmed the effect of Ppd-H1 on leaf size. Differences in the duration of leaf growth and consequent variation in leaf cell number were responsible for the leaf size differences between the Ppd-H1 variants. The Ppd-H1-dependent induction of the BARLEY MADS BOX genes BM3 and BM8 in the leaf correlated with reductions in leaf size and leaf number. Our results indicate that leaf size is controlled by the Ppd-H1- and photoperiod-dependent progression of plant development. The coordination of leaf growth with flowering may be part of a reproductive strategy to optimize resource allocation to the developing inflorescences and seeds. © 2016 American Society of Plant Biologists. All rights reserved.

Study of alteration in the mechanical properties in hybrid nanocomposite of polypropylene/sisal fibers/mineral clay irradiated with gamma rays

Energy Technology Data Exchange (ETDEWEB)

Pereira, Nilson C.; Terence, Mauro C.; Miranda, Leila F., E-mail: nilpereira@mackenzie.com.b [Universidade Presbiteriana Mackenzie, Sao Paulo, SP (Brazil). Escola de Engenharia. Curso de Engenharia de Materiais

2009-07-01

A new material class formed with reinforced filler, hybrid of organic and inorganic materials provides the technological development of materials with modified properties. And among great numbers of properties that can be modified by presence of hybrid filler to stand out the tension resistance. Polymer shows behavior of tensions and deformation that are not related of simple form. The answer of this material at mechanicals solicitations depends of structural factors and externals variables. As structural factors can be, for example, molecular weight, ramifications and crosslink. As external variables can be, for example, temperature, time or velocity of deformation, kind of solicitation and others. This work was possible to verify as nanostructures materials behavior, mechanically, after were submitted gamma radiation. This work utilized as polymeric matrix, recycled polypropylene, and as hybrid filler, a mixture of montimorillonite mineral clay with natural sisal fibers. It is known that form to magnify the tensile resistance is increase the number of crosslink of principal chain for gamma radiation. After irradiation the polypropylene was crosslinked structures that are result recombination of radicals formed during process of irradiation. It.s known that radicals formed occur preferentially in the amorphous region of polymer. Considering that polymeric matrix polypropylene, without addition fillers suffer strong structural influence when irradiated, was possible verify change in the extension, tensile strength and also maxim tensile in rupture, when this matrix was incorporated with fillers hybrids. (author)

Study of alteration in the mechanical properties in hybrid nanocomposite of polypropylene/sisal fibers/mineral clay irradiated with gamma rays

International Nuclear Information System (INIS)

Pereira, Nilson C.; Terence, Mauro C.; Miranda, Leila F.

2009-01-01

A new material class formed with reinforced filler, hybrid of organic and inorganic materials provides the technological development of materials with modified properties. And among great numbers of properties that can be modified by presence of hybrid filler to stand out the tension resistance. Polymer shows behavior of tensions and deformation that are not related of simple form. The answer of this material at mechanicals solicitations depends of structural factors and externals variables. As structural factors can be, for example, molecular weight, ramifications and crosslink. As external variables can be, for example, temperature, time or velocity of deformation, kind of solicitation and others. This work was possible to verify as nanostructures materials behavior, mechanically, after were submitted gamma radiation. This work utilized as polymeric matrix, recycled polypropylene, and as hybrid filler, a mixture of montimorillonite mineral clay with natural sisal fibers. It is known that form to magnify the tensile resistance is increase the number of crosslink of principal chain for gamma radiation. After irradiation the polypropylene was crosslinked structures that are result recombination of radicals formed during process of irradiation. It.s known that radicals formed occur preferentially in the amorphous region of polymer. Considering that polymeric matrix polypropylene, without addition fillers suffer strong structural influence when irradiated, was possible verify change in the extension, tensile strength and also maxim tensile in rupture, when this matrix was incorporated with fillers hybrids. (author)

Wind increases leaf water use efficiency.

Science.gov (United States)

Schymanski, Stanislaus J; Or, Dani

2016-07-01

A widespread perception is that, with increasing wind speed, transpiration from plant leaves increases. However, evidence suggests that increasing wind speed enhances carbon dioxide (CO2 ) uptake while reducing transpiration because of more efficient convective cooling (under high solar radiation loads). We provide theoretical and experimental evidence that leaf water use efficiency (WUE, carbon uptake per water transpired) commonly increases with increasing wind speed, thus improving plants' ability to conserve water during photosynthesis. Our leaf-scale analysis suggests that the observed global decrease in near-surface wind speeds could have reduced WUE at a magnitude similar to the increase in WUE attributed to global rise in atmospheric CO2 concentrations. However, there is indication that the effect of long-term trends in wind speed on leaf gas exchange may be compensated for by the concurrent reduction in mean leaf sizes. These unintuitive feedbacks between wind, leaf size and water use efficiency call for re-evaluation of the role of wind in plant water relations and potential re-interpretation of temporal and geographic trends in leaf sizes. © 2015 The Authors. Plant, Cell & Environment published by John Wiley & Sons Ltd.

VEGETAL COVERING IN CUT SLOPES BY MEANS OF GEOCELLS OF RUBBERIZED SISAL BIOBLANKETS IN BRASILIA/DF, BRAZIL

Directory of Open Access Journals (Sweden)

Maurizio Sponga

2005-05-01

Full Text Available The strongly wavy relief transposition for implantation of highways has became intensely used in the last decades by means of tunnels, cuts and fillings, causing impacts to the landscape in result of some factors, as decapitation of surfaces, abrupt transformation of land morphology, disequilibrium of superficial and sub superficial water circulation, waste handling sistems, enchainment of erosive processes etc. As an alleviating measure of part of the impacts generated for the excavations for constructing the roadways, procedures of containment and vegetal resetting of surfaces for reduction of the erosive processes and stabilization of mass movements are adopted. The found terrain are very diversified and several occasions the vegetal covering becomes difficult in reason of the physical-chemical characteristics for germination to be inadequate. In areas of high risk to the occupation with stability problems, commonly they use covering with projected concrete for containment of hillsides, that parallelly causes strong environmental and visual impact in the intervention area, and furthermore, possibly, not consisting insolutions duly adequate or definitive for these situations.The search for alternatives is frequent in academic medium as much as in the private initiative for techniques for containment of hillsides and more economic erosion control, looking for lesser ambient impacts and better results. The search of these alternatives gradually becomes technically systemizing itself, aiming at the recovery of the conditions of dynamic balance of the impacted landscapes due to the explosive increase of social and environmental problems intrinsically related.In this direction, it will be presented the description of a work of vegetal covering by grass in plates, antierosive bioblanket and geocells in fibers of rubberized sisal for the confinement of soil in cut slopes of a highway in Brasilia/DF, in Brazil. This technique presented excellent

Relating Stomatal Conductance to Leaf Functional Traits.

Science.gov (United States)

Kröber, Wenzel; Plath, Isa; Heklau, Heike; Bruelheide, Helge

2015-10-12

Leaf functional traits are important because they reflect physiological functions, such as transpiration and carbon assimilation. In particular, morphological leaf traits have the potential to summarize plants strategies in terms of water use efficiency, growth pattern and nutrient use. The leaf economics spectrum (LES) is a recognized framework in functional plant ecology and reflects a gradient of increasing specific leaf area (SLA), leaf nitrogen, phosphorus and cation content, and decreasing leaf dry matter content (LDMC) and carbon nitrogen ratio (CN). The LES describes different strategies ranging from that of short-lived leaves with high photosynthetic capacity per leaf mass to long-lived leaves with low mass-based carbon assimilation rates. However, traits that are not included in the LES might provide additional information on the species' physiology, such as those related to stomatal control. Protocols are presented for a wide range of leaf functional traits, including traits of the LES, but also traits that are independent of the LES. In particular, a new method is introduced that relates the plants' regulatory behavior in stomatal conductance to vapor pressure deficit. The resulting parameters of stomatal regulation can then be compared to the LES and other plant functional traits. The results show that functional leaf traits of the LES were also valid predictors for the parameters of stomatal regulation. For example, leaf carbon concentration was positively related to the vapor pressure deficit (vpd) at the point of inflection and the maximum of the conductance-vpd curve. However, traits that are not included in the LES added information in explaining parameters of stomatal control: the vpd at the point of inflection of the conductance-vpd curve was lower for species with higher stomatal density and higher stomatal index. Overall, stomata and vein traits were more powerful predictors for explaining stomatal regulation than traits used in the LES.

7 CFR 30.31 - Classification of leaf tobacco.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Classification of leaf tobacco. 30.31 Section 30.31... REGULATIONS TOBACCO STOCKS AND STANDARDS Classification of Leaf Tobacco Covering Classes, Types and Groups of Grades § 30.31 Classification of leaf tobacco. For the purpose of this classification leaf tobacco shall...

Biophysical control of leaf temperature

Science.gov (United States)

Dong, N.; Prentice, I. C.; Wright, I. J.

2014-12-01

In principle sunlit leaves can maintain their temperatures within a narrower range than ambient temperatures. This is an important and long-known (but now overlooked) prediction of energy balance theory. Net radiation at leaf surface in steady state (which is reached rapidly) must be equal to the combination of sensible and latent heat exchanges with surrounding air, the former being proportional to leaf-to-air temperature difference (ΔT), the latter to the transpiration rate. We present field measurements of ΔT which confirm the existence of a 'crossover temperature' in the 25-30˚C range for species in a tropical savanna and a tropical rainforest environment. This finding is consistent with a simple representation of transpiration as a function of net radiation and temperature (Priestley-Taylor relationship) assuming an entrainment factor (ω) somewhat greater than the canonical value of 0.26. The fact that leaves in tropical forests are typically cooler than surrounding air, often already by solar noon, is consistent with a recently published comparison of MODIS day-time land-surface temperatures with air temperatures. Theory further predicts a strong dependence of leaf size (which is inversely related to leaf boundary-layer conductance, and therefore to absolute magnitude of ΔT) on moisture availability. Theoretically, leaf size should be determined by either night-time constraints (risk of frost damage to active leaves) or day-time constraints (risk of heat stress damage),with the former likely to predominate - thereby restricting the occurrence of large leaves - at high latitudes. In low latitudes, daytime maximum leaf size is predicted to increase with temperature, provided that water is plentiful. If water is restricted, however, transpiration cannot proceed at the Priestley-Taylor rate, and it quickly becomes advantageous for plants to have small leaves, which do not heat up much above the temperature of their surroundings. The difference between leaf

Possible Roles of Strigolactones during Leaf Senescence

Directory of Open Access Journals (Sweden)

Yusuke Yamada

2015-09-01

Full Text Available Leaf senescence is a complicated developmental process that involves degenerative changes and nutrient recycling. The progress of leaf senescence is controlled by various environmental cues and plant hormones, including ethylene, jasmonic acid, salicylic acid, abscisic acid, cytokinins, and strigolactones. The production of strigolactones is induced in response to nitrogen and phosphorous deficiency. Strigolactones also accelerate leaf senescence and regulate shoot branching and root architecture. Leaf senescence is actively promoted in a nutrient-poor soil environment, and nutrients are transported from old leaves to young tissues and seeds. Strigolactones might act as important signals in response to nutrient levels in the rhizosphere. In this review, we discuss the possible roles of strigolactones during leaf senescence.

Cotton leaf curl Burewala virus with intact or mutant transcriptional activator proteins: complexity of cotton leaf curl disease.

Science.gov (United States)

Kumar, Jitendra; Gunapati, Samatha; Alok, Anshu; Lalit, Adarsh; Gadre, Rekha; Sharma, Naresh C; Roy, Joy K; Singh, Sudhir P

2015-05-01

Cotton leaf curl disease (CLCuD) is a serious disease of cotton on the Indian subcontinent. In the present study, three cotton leaf curl viruses, cotton leaf curl Burewala virus (CLCuBuV), cotton leaf curl Kokhran virus (CLCuKoV) and cotton leaf curl Multan virus (CLCuMV), and their associated satellites, cotton leaf curl Multan betasatellite (CLCuMB) and cotton leaf curl Multan alphasatellite (CLCuMA), were detected. CLCuBuV with either intact (CLCuBuV-1) or mutant (CLCuBuV-2) transcriptional activator protein (TrAP) were detected in different plants. Agroinoculation with CLCuBuV-1 or CLCuBuV-2 together with CLCuMB and CLCuMA, resulted in typical leaf curling and stunting of tobacco plants. Inoculation with CLCuKoV or an isolate of CLCuMV (CLCuMV-2), together with CLCuMB and CLCuMA, induced severe leaf curling, while the other isolate of CLCuMV (CLCuMV-1), which was recombinant in origin, showed mild leaf curling in tobacco. To investigate the effect of intact or mutant TrAP and also the recombination events, CLCuBuV-1, CLCuBuV-2, CLCuMV-1 or CLCuMV-2 together with the satellites (CLCuMA and CLCuMB) were transferred to cotton via whitefly-mediated transmission. Cotton plants containing CLCuBuV-1, CLCuBuV-2 or CLCuMV-2 together with satellites showed curling and stunting, whereas the plants having CLCuMV-1 and the satellites showed only mild and indistinguishable symptoms. CLCuBuV-1 (intact TrAP) showed severe symptoms in comparison to CLCuBuV-2 (mutant TrAP). The present study reveals that two types of CLCuBuV, one with an intact TrAP and the other with a mutant TrAP, exist in natural infection of cotton in India. Additionally, CLCuMuV-1, which has a recombinant origin, induces mild symptoms in comparison to the other CLCuMV isolates.

Textile composites based on natural fibers

CSIR Research Space (South Africa)

Li, Yan

2009-04-01

Full Text Available . The two kinds of fiber surface treatment methods were permanganate treatment and silane treatment. Vinyl ester was used as the matrix. The permeability values of sisal textile before and after fiber surface treatments are listed in Table 3. Comparisons... and more liquid resin flow through inter-bundles. Figure 4. Intra-bundle and inter-bundle flows As reported, permanganate, as an oxidant, can etch sisal fiber surface [20]. Scanning electronic micrograph of a permanganate treated sisal fiber...

The plant leaf movement analyzer (PALMA): a simple tool for the analysis of periodic cotyledon and leaf movement in Arabidopsis thaliana.

Science.gov (United States)

Wagner, Lucas; Schmal, Christoph; Staiger, Dorothee; Danisman, Selahattin

2017-01-01

The analysis of circadian leaf movement rhythms is a simple yet effective method to study effects of treatments or gene mutations on the circadian clock of plants. Currently, leaf movements are analysed using time lapse photography and subsequent bioinformatics analyses of leaf movements. Programs that are used for this purpose either are able to perform one function (i.e. leaf tip detection or rhythm analysis) or their function is limited to specific computational environments. We developed a leaf movement analysis tool-PALMA-that works in command line and combines image extraction with rhythm analysis using Fast Fourier transformation and non-linear least squares fitting. We validated PALMA in both simulated time series and in experiments using the known short period mutant sensitivity to red light reduced 1 ( srr1 - 1 ). We compared PALMA with two established leaf movement analysis tools and found it to perform equally well. Finally, we tested the effect of reduced iron conditions on the leaf movement rhythms of wild type plants. Here, we found that PALMA successfully detected period lengthening under reduced iron conditions. PALMA correctly estimated the period of both simulated and real-life leaf movement experiments. As a platform-independent console-program that unites both functions needed for the analysis of circadian leaf movements it is a valid alternative to existing leaf movement analysis tools.

Effects of nitrogen application rate and leaf age on the distribution pattern of leaf SPAD readings in the rice canopy.

Directory of Open Access Journals (Sweden)

Hu Yang

Full Text Available A Soil-Plant Analysis Development (SPAD chlorophyll meter can be used as a simple tool for evaluating N concentration of the leaf and investigating the combined effects of nitrogen rate and leaf age on N distribution. We conducted experiments in a paddy field over two consecutive years (2008-2009 using rice plants treated with six different N application levels. N distribution pattern was determined by SPAD readings based on the temporal dynamics of N concentrations in individual leaves. At 62 days after transplantation (DAT in 2008 and DAT 60 in 2009, leaf SPAD readings increased from the upper to lower in the rice canopy that received N levels of 150 to 375 kg ha(-1The differences in SPAD readings between the upper and lower leaf were larger under higher N application rates. However, as plants grew, this atypical distribution of SPAD readings in canopy leaf quickly reversed to the general order. In addition, temporal dynamics of the leaf SPAD readings (N concentrations were fitted to a piecewise function. In our model, changes in leaf SPAD readings were divided into three stages: growth, functioning, and senescence periods. The leaf growth period lasted approximately 6 days, and cumulative growing days were not affected by N application rates. The leaf functioning period was represented with a relatively stable SPAD reading related to N application rate, and cumulative growing days were extended with increasing N application rates. A quadratic equation was utilized to describe the relationship between SPAD readings and leaf age during the leaf senescence period. The rate of decrease in SPAD readings increased with the age of leaves, but the rate was slowed by N application. As leaves in the lower canopy were physiologically older than leaves in the upper canopy, the rate of decrease in SPAD readings was faster in the lower leaves.

A hairy-leaf gene, BLANKET LEAF, of wild Oryza nivara increases photosynthetic water use efficiency in rice.

Science.gov (United States)

Hamaoka, Norimitsu; Yasui, Hideshi; Yamagata, Yoshiyuki; Inoue, Yoko; Furuya, Naruto; Araki, Takuya; Ueno, Osamu; Yoshimura, Atsushi

2017-12-01

High water use efficiency is essential to water-saving cropping. Morphological traits that affect photosynthetic water use efficiency are not well known. We examined whether leaf hairiness improves photosynthetic water use efficiency in rice. A chromosome segment introgression line (IL-hairy) of wild Oryza nivara (Acc. IRGC105715) with the genetic background of Oryza sativa cultivar 'IR24' had high leaf pubescence (hair). The leaf hairs developed along small vascular bundles. Linkage analysis in BC 5 F 2 and F 3 populations showed that the trait was governed by a single gene, designated BLANKET LEAF (BKL), on chromosome 6. IL-hairy plants had a warmer leaf surface in sunlight, probably due to increased boundary layer resistance. They had a lower transpiration rate under moderate and high light intensities, resulting in higher photosynthetic water use efficiency. Introgression of BKL on chromosome 6 from O. nivara improved photosynthetic water use efficiency in the genetic background of IR24.

Seasonal patterns of leaf gas exchange and water relations in dry rain forest trees of contrasting leaf phenology.

Science.gov (United States)

Choat, Brendan; Ball, Marilyn C; Luly, Jon G; Donnelly, Christine F; Holtum, Joseph A M

2006-05-01

Diurnal and seasonal patterns of leaf gas exchange and water relations were examined in tree species of contrasting leaf phenology growing in a seasonally dry tropical rain forest in north-eastern Australia. Two drought-deciduous species, Brachychiton australis (Schott and Endl.) A. Terracc. and Cochlospermum gillivraei Benth., and two evergreen species, Alphitonia excelsa (Fenzal) Benth. and Austromyrtus bidwillii (Benth.) Burret. were studied. The deciduous species had higher specific leaf areas and maximum photosynthetic rates per leaf dry mass in the wet season than the evergreens. During the transition from wet season to dry season, total canopy area was reduced by 70-90% in the deciduous species and stomatal conductance (g(s)) and assimilation rate (A) were markedly lower in the remaining leaves. Deciduous species maintained daytime leaf water potentials (Psi(L)) at close to or above wet season values by a combination of stomatal regulation and reduction in leaf area. Thus, the timing of leaf drop in deciduous species was not associated with large negative values of daytime Psi(L) (greater than -1.6 MPa) or predawn Psi(L) (greater than -1.0 MPa). The deciduous species appeared sensitive to small perturbations in soil and leaf water status that signalled the onset of drought. The evergreen species were less sensitive to the onset of drought and g(s) values were not significantly lower during the transitional period. In the dry season, the evergreen species maintained their canopies despite increasing water-stress; however, unlike Eucalyptus species from northern Australian savannas, A and g(s) were significantly lower than wet season values.

Leaf area index from litter collection: impact of specific leaf area variability within a beech stand

Energy Technology Data Exchange (ETDEWEB)

Bouriaud, O. [Inst. National de la Recherche Agronomique, Centre de Recherches Forestieres de Nancy, Champenoux (France); Soudani, K. [Univ. Paris-Sud XI, Dept. d' Ecophysiologie Vegetale, Lab. Ecologie Systematique et Evolution, Orsay Cedex (France); Breda, N. [Inst. National de la Recherche Agronomique, Centre de Recherches Forestieres de Nancy, Champenoux (France)

2003-06-01

Litter fall collection is a direct method widely used to estimate leaf area index (LAI) in broad-leaved forest stands. Indirect measurements using radiation transmittance and gap fraction theory are often compared and calibrated against litter fall, which is considered as a reference method, but few studies address the question of litter specific leaf area (SLA) measurement and variability. SLA (leaf area per unit of dry weight, m{sup 2}{center_dot}g{sup -1}) is used to convert dry leaf litter biomass (g .m{sup -}2) into leaf area per ground unit area (m{sup 2}{center_dot}m{sup -2}). We paid special attention to this parameter in two young beech stands (dense and thinned) in northeastern France. The variability of both canopy (closure, LAI) and site conditions (soil properties, vegetation) was investigated as potential contributing factors to beech SLA variability. A systematic description of soil and floristic composition was performed and three types of soil were identified. Ellenberg's indicator values were averaged for each plot to assess nitrogen soil content. SLA of beech litter was measured three times during the fall in 23 plots in the stands (40 ha). Litter was collected bimonthly in square-shaped traps (0.5 m{sup 2}) and dried. Before drying, 30 leaves per plot and for each date were sampled, and leaf length, width, and area were measured with the help of a LI-COR areameter. SLA was calculated as the ratio of cumulated leaf area to total dry weight of the 30 leaves. Leaves characteristics per plot were averaged for the three dates of litter collection. Plant area index (PAI), estimated using the LAI-2000 plant canopy analyser and considering only the upper three rings, ranged from 2.9 to 8.1. Specific leaf area of beech litter was also highly different from one plot to the other, ranging from 150 to 320 cm{sup 2}{center_dot}g{sup -1}. Nevertheless, no relationship was found between SLA and stand canopy closure or PAI On the contrary, a significant

Leaf area index from litter collection: impact of specific leaf area variability within a beech stand

International Nuclear Information System (INIS)

Bouriaud, O.; Soudani, K.; Breda, N.

2003-01-01

Litter fall collection is a direct method widely used to estimate leaf area index (LAI) in broad-leaved forest stands. Indirect measurements using radiation transmittance and gap fraction theory are often compared and calibrated against litter fall, which is considered as a reference method, but few studies address the question of litter specific leaf area (SLA) measurement and variability. SLA (leaf area per unit of dry weight, m 2 ·g -1 ) is used to convert dry leaf litter biomass (g .m - 2) into leaf area per ground unit area (m 2 ·m -2 ). We paid special attention to this parameter in two young beech stands (dense and thinned) in northeastern France. The variability of both canopy (closure, LAI) and site conditions (soil properties, vegetation) was investigated as potential contributing factors to beech SLA variability. A systematic description of soil and floristic composition was performed and three types of soil were identified. Ellenberg's indicator values were averaged for each plot to assess nitrogen soil content. SLA of beech litter was measured three times during the fall in 23 plots in the stands (40 ha). Litter was collected bimonthly in square-shaped traps (0.5 m 2 ) and dried. Before drying, 30 leaves per plot and for each date were sampled, and leaf length, width, and area were measured with the help of a LI-COR areameter. SLA was calculated as the ratio of cumulated leaf area to total dry weight of the 30 leaves. Leaves characteristics per plot were averaged for the three dates of litter collection. Plant area index (PAI), estimated using the LAI-2000 plant canopy analyser and considering only the upper three rings, ranged from 2.9 to 8.1. Specific leaf area of beech litter was also highly different from one plot to the other, ranging from 150 to 320 cm 2 ·g -1 . Nevertheless, no relationship was found between SLA and stand canopy closure or PAI On the contrary, a significant relationship between SLA and soil properties was observed. Both SLA

Effect of nitrogen supply on leaf growth, leaf nitrogen economy and photosynthetic capacity in potato

NARCIS (Netherlands)

Vos, J.; Putten, van der P.E.L.

1998-01-01

Literature reports show little effect of nitrogen supply on radiation use efficiency in potato and in other dicotyledonous C3 species. This paper tests the hypothesis that potato reduces leaf size rather than leaf nitrogen concentration and photosynthetic capacity when nitrogen is in short supply.

Leaf extraction and analysis framework graphical user interface: segmenting and analyzing the structure of leaf veins and areoles.

Science.gov (United States)

Price, Charles A; Symonova, Olga; Mileyko, Yuriy; Hilley, Troy; Weitz, Joshua S

2011-01-01

Interest in the structure and function of physical biological networks has spurred the development of a number of theoretical models that predict optimal network structures across a broad array of taxonomic groups, from mammals to plants. In many cases, direct tests of predicted network structure are impossible given the lack of suitable empirical methods to quantify physical network geometry with sufficient scope and resolution. There is a long history of empirical methods to quantify the network structure of plants, from roots, to xylem networks in shoots and within leaves. However, with few exceptions, current methods emphasize the analysis of portions of, rather than entire networks. Here, we introduce the Leaf Extraction and Analysis Framework Graphical User Interface (LEAF GUI), a user-assisted software tool that facilitates improved empirical understanding of leaf network structure. LEAF GUI takes images of leaves where veins have been enhanced relative to the background, and following a series of interactive thresholding and cleaning steps, returns a suite of statistics and information on the structure of leaf venation networks and areoles. Metrics include the dimensions, position, and connectivity of all network veins, and the dimensions, shape, and position of the areoles they surround. Available for free download, the LEAF GUI software promises to facilitate improved understanding of the adaptive and ecological significance of leaf vein network structure.

Leaf Area Estimation Models for Ginger ( Zingibere officinale Rosc ...

African Journals Online (AJOL)

The study was carried out to develop leaf area estimation models for three cultivars (37/79, 38/79 and 180/73) and four accessions (29/86, 30/86, 47/86 and 52/86) of ginger. Significant variations were observed among the tested genotypes in leaf length (L), leaf width (W) and actual leaf area (ALA). Leaf area was highly ...

A Global Data Set of Leaf Photosynthetic Rates, Leaf N and P, and Specific Leaf Area

Data.gov (United States)

National Aeronautics and Space Administration — ABSTRACT: This global data set of photosynthetic rates and leaf nutrient traits was compiled from a comprehensive literature review. It includes estimates of Vcmax...

A Global Data Set of Leaf Photosynthetic Rates, Leaf N and P, and Specific Leaf Area

Data.gov (United States)

National Aeronautics and Space Administration — This global data set of photosynthetic rates and leaf nutrient traits was compiled from a comprehensive literature review. It includes estimates of Vcmax (maximum...

Does investment in leaf defenses drive changes in leaf economic strategy? A focus on whole-plant ontogeny.

Science.gov (United States)

Mason, Chase M; Donovan, Lisa A

2015-04-01

Leaf defenses have long been studied in the context of plant growth rate, resource availability, and optimal investment theory. Likewise, one of the central modern paradigms of plant ecophysiology, the leaf economics spectrum (LES), has been extensively studied in the context of these factors across ecological scales ranging from global species data sets to temporal shifts within individuals. Despite strong physiological links between LES strategy and leaf defenses in structure, function, and resource investment, the relationship between these trait classes has not been well explored. This study investigates the relationship between leaf defenses and LES strategy across whole-plant ontogeny in three diverse Helianthus species known to exhibit dramatic ontogenetic shifts in LES strategy, focusing primarily on physical and quantitative chemical defenses. Plants were grown under controlled environmental conditions and sampled for LES and defense traits at four ontogenetic stages. Defenses were found to shift strongly with ontogeny, and to correlate strongly with LES strategy. More advanced ontogenetic stages with more conservative LES strategy leaves had higher tannin activity and toughness in all species, and higher leaf dry matter content in two of three species. Modeling results in two species support the conclusion that changes in defenses drive changes in LES strategy through ontogeny, and in one species that changes in defenses and LES strategy are likely independently driven by ontogeny. Results of this study support the hypothesis that leaf-level allocation to defenses might be an important determinant of leaf economic traits, where high investment in defenses drives a conservative LES strategy.

Influence of Vegetation Structure on Lidar-derived Canopy Height and Fractional Cover in Forested Riparian Buffers During Leaf-Off and Leaf-On Conditions

Science.gov (United States)

Wasser, Leah; Day, Rick; Chasmer, Laura; Taylor, Alan

2013-01-01

Estimates of canopy height (H) and fractional canopy cover (FC) derived from lidar data collected during leaf-on and leaf-off conditions are compared with field measurements from 80 forested riparian buffer plots. The purpose is to determine if existing lidar data flown in leaf-off conditions for applications such as terrain mapping can effectively estimate forested riparian buffer H and FC within a range of riparian vegetation types. Results illustrate that: 1) leaf-off and leaf-on lidar percentile estimates are similar to measured heights in all plots except those dominated by deciduous compound-leaved trees where lidar underestimates H during leaf off periods; 2) canopy height models (CHMs) underestimate H by a larger margin compared to percentile methods and are influenced by vegetation type (conifer needle, deciduous simple leaf or deciduous compound leaf) and canopy height variability, 3) lidar estimates of FC are within 10% of plot measurements during leaf-on periods, but are underestimated during leaf-off periods except in mixed and conifer plots; and 4) depth of laser pulse penetration lower in the canopy is more variable compared to top of the canopy penetration which may influence within canopy vegetation structure estimates. This study demonstrates that leaf-off lidar data can be used to estimate forested riparian buffer canopy height within diverse vegetation conditions and fractional canopy cover within mixed and conifer forests when leaf-on lidar data are not available. PMID:23382966

Leaf structural characteristics are less important than leaf chemical properties in determining the response of leaf mass per area and photosynthesis of Eucalyptus saligna to industrial-age changes in [CO2] and temperature.

Science.gov (United States)

Xu, Cheng-Yuan; Salih, Anya; Ghannoum, Oula; Tissue, David T

2012-10-01

The rise in atmospheric [CO(2)] is associated with increasing air temperature. However, studies on plant responses to interactive effects of [CO(2)] and temperature are limited, particularly for leaf structural attributes. In this study, Eucalyptus saligna plants were grown in sun-lit glasshouses differing in [CO(2)] (290, 400, and 650 µmol mol(-1)) and temperature (26 °C and 30 °C). Leaf anatomy and chloroplast parameters were assessed with three-dimensional confocal microscopy, and the interactive effects of [CO(2)] and temperature were quantified. The relative influence of leaf structural attributes and chemical properties on the variation of leaf mass per area (LMA) and photosynthesis within these climate regimes was also determined. Leaf thickness and mesophyll size increased in higher [CO(2)] but decreased at the warmer temperature; no treatment interaction was observed. In pre-industrial [CO(2)], warming reduced chloroplast diameter without altering chloroplast number per cell, but the opposite pattern (reduced chloroplast number per cell and unchanged chloroplast diameter) was observed in both current and projected [CO(2)]. The variation of LMA was primarily explained by total non-structural carbohydrate (TNC) concentration rather than leaf thickness. Leaf photosynthetic capacity (light- and [CO(2)]-saturated rate at 28 °C) and light-saturated photosynthesis (under growth [CO(2)] and temperature) were primarily determined by leaf nitrogen contents, while secondarily affected by chloroplast gas exchange surface area and chloroplast number per cell, respectively. In conclusion, leaf structural attributes are less important than TNC and nitrogen in affecting LMA and photosynthesis responses to the studied climate regimes, indicating that leaf structural attributes have limited capacity to adjust these functional traits in a changing climate.

Dependence of fluence errors in dynamic IMRT on leaf-positional errors varying with time and leaf number

International Nuclear Information System (INIS)

Zygmanski, Piotr; Kung, Jong H.; Jiang, Steve B.; Chin, Lee

2003-01-01

In d-MLC based IMRT, leaves move along a trajectory that lies within a user-defined tolerance (TOL) about the ideal trajectory specified in a d-MLC sequence file. The MLC controller measures leaf positions multiple times per second and corrects them if they deviate from ideal positions by a value greater than TOL. The magnitude of leaf-positional errors resulting from finite mechanical precision depends on the performance of the MLC motors executing leaf motions and is generally larger if leaves are forced to move at higher speeds. The maximum value of leaf-positional errors can be limited by decreasing TOL. However, due to the inherent time delay in the MLC controller, this may not happen at all times. Furthermore, decreasing the leaf tolerance results in a larger number of beam hold-offs, which, in turn leads, to a longer delivery time and, paradoxically, to higher chances of leaf-positional errors (≤TOL). On the other end, the magnitude of leaf-positional errors depends on the complexity of the fluence map to be delivered. Recently, it has been shown that it is possible to determine the actual distribution of leaf-positional errors either by the imaging of moving MLC apertures with a digital imager or by analysis of a MLC log file saved by a MLC controller. This leads next to an important question: What is the relation between the distribution of leaf-positional errors and fluence errors. In this work, we introduce an analytical method to determine this relation in dynamic IMRT delivery. We model MLC errors as Random-Leaf Positional (RLP) errors described by a truncated normal distribution defined by two characteristic parameters: a standard deviation σ and a cut-off value Δx 0 (Δx 0 ∼TOL). We quantify fluence errors for two cases: (i) Δx 0 >>σ (unrestricted normal distribution) and (ii) Δx 0 0 --limited normal distribution). We show that an average fluence error of an IMRT field is proportional to (i) σ/ALPO and (ii) Δx 0 /ALPO, respectively, where

The Nissan LEAF electric powertrain

Energy Technology Data Exchange (ETDEWEB)

Nakazawa, Shinsuke [Nissan Motor Co., Ltd. (Japan)

2011-07-01

The need for CO{sub 2} reduction as a countermeasure to global warming, and to move away from our dependence on fossil fuels as a countermeasure to energy security are urgent issues. One of the ultimate goals to achieving these targets is to develop a 'Zero emission car' such as an electric vehicle or a fuel cell vehicle, along with the manufacturing of clean energy. Nissan have developed a new powertrain for the electric vehicle, and have installed it in the Nissan LEAF. Sales of the Nissan LEAF started in North America, Europe and Japan in 2010, with plans to sell it globally by 2012. In order to achieve an improved driving range, power performance and drivability performance, Nissan have adapted a high efficiency synchronous motor, a water-cooled inverter, and reducer. Moreover, the Nissan LEAF has the capability of a 3.3kW AC charge and a 50kW DC quick charge. This presentation will introduce the features of the electric powertrain adopted for Nissan LEAF. (orig.)

A non-destructive method for estimating onion leaf area

Directory of Open Access Journals (Sweden)

Córcoles J.I.

2015-06-01

Full Text Available Leaf area is one of the most important parameters for characterizing crop growth and development, and its measurement is useful for examining the effects of agronomic management on crop production. It is related to interception of radiation, photosynthesis, biomass accumulation, transpiration and gas exchange in crop canopies. Several direct and indirect methods have been developed for determining leaf area. The aim of this study is to develop an indirect method, based on the use of a mathematical model, to compute leaf area in an onion crop using non-destructive measurements with the condition that the model must be practical and useful as a Decision Support System tool to improve crop management. A field experiment was conducted in a 4.75 ha commercial onion plot irrigated with a centre pivot system in Aguas Nuevas (Albacete, Spain, during the 2010 irrigation season. To determine onion crop leaf area in the laboratory, the crop was sampled on four occasions between 15 June and 15 September. At each sampling event, eight experimental plots of 1 m2 were used and the leaf area for individual leaves was computed using two indirect methods, one based on the use of an automated infrared imaging system, LI-COR-3100C, and the other using a digital scanner EPSON GT-8000, obtaining several images that were processed using Image J v 1.43 software. A total of 1146 leaves were used. Before measuring the leaf area, 25 parameters related to leaf length and width were determined for each leaf. The combined application of principal components analysis and cluster analysis for grouping leaf parameters was used to reduce the number of variables from 25 to 12. The parameter derived from the product of the total leaf length (L and the leaf diameter at a distance of 25% of the total leaf length (A25 gave the best results for estimating leaf area using a simple linear regression model. The model obtained was useful for computing leaf area using a non

The Use of Lignocellulosic Byproducts and Cellulose Nanocrystals within Particleboard Production

DEFF Research Database (Denmark)

Mesquita, Ricardo Gabriel de Almeida

The objective of this work was to study the particleboard production using Eucalyptus particles, sisal filaments, coconut filaments (coir) and sugarcane bagasse particles (SCB). All particleboards were made in three layers (face / core / face) using urea-formaldehyde adhesive (UF). Coir and sisal......) and thermal conductivity (TC). The particleboards reinforced with sisal did not show satisfactory results for most of the properties evaluated (MOE, MOR, WA, IB and TC), but those reinforced with coconut, showed properties very similar to the particleboards made only with Eucalyptus particles, demonstrating...

Modeling canopy-level productivity: is the "big-leaf" simplification acceptable?

Science.gov (United States)

Sprintsin, M.; Chen, J. M.

2009-05-01

The "big-leaf" approach to calculating the carbon balance of plant canopies assumes that canopy carbon fluxes have the same relative responses to the environment as any single unshaded leaf in the upper canopy. Widely used light use efficiency models are essentially simplified versions of the big-leaf model. Despite its wide acceptance, subsequent developments in the modeling of leaf photosynthesis and measurements of canopy physiology have brought into question the assumptions behind this approach showing that big leaf approximation is inadequate for simulating canopy photosynthesis because of the additional leaf internal control on carbon assimilation and because of the non-linear response of photosynthesis on leaf nitrogen and absorbed light, and changes in leaf microenvironment with canopy depth. To avoid this problem a sunlit/shaded leaf separation approach, within which the vegetation is treated as two big leaves under different illumination conditions, is gradually replacing the "big-leaf" strategy, for applications at local and regional scales. Such separation is now widely accepted as a more accurate and physiologically based approach for modeling canopy photosynthesis. Here we compare both strategies for Gross Primary Production (GPP) modeling using the Boreal Ecosystem Productivity Simulator (BEPS) at local (tower footprint) scale for different land cover types spread over North America: two broadleaf forests (Harvard, Massachusetts and Missouri Ozark, Missouri); two coniferous forests (Howland, Maine and Old Black Spruce, Saskatchewan); Lost Creek shrubland site (Wisconsin) and Mer Bleue petland (Ontario). BEPS calculates carbon fixation by scaling Farquhar's leaf biochemical model up to canopy level with stomatal conductance estimated by a modified version of the Ball-Woodrow-Berry model. The "big-leaf" approach was parameterized using derived leaf level parameters scaled up to canopy level by means of Leaf Area Index. The influence of sunlit

Baby leaf lettuce germplasm enhancement: developing diverse populations with resistance to bacterial leaf spot caused by Xanthomonas campestris pv. vitians

Science.gov (United States)

Baby leaf lettuce cultivars with resistance to bacterial leaf spot (BLS) caused by Xanthomonas campestris pv. vitians (Xcv) are needed to reduce crop losses. The objectives of this research were to assess the genetic diversity for BLS resistance in baby leaf lettuce cultivars and to select early gen...

Leaf turgor loss point is correlated with drought tolerance and leaf carbon economics traits.

Science.gov (United States)

Zhu, Shi-Dan; Chen, Ya-Jun; Ye, Qing; He, Peng-Cheng; Liu, Hui; Li, Rong-Hua; Fu, Pei-Li; Jiang, Guo-Feng; Cao, Kun-Fang

2018-05-01

Leaf turgor loss point (πtlp) indicates the capacity of a plant to maintain cell turgor pressure during dehydration, which has been proven to be strongly predictive of the plant response to drought. In this study, we compiled a data set of πtlp for 1752 woody plant individuals belonging to 389 species from nine major woody biomes in China, along with reduced sample size of hydraulic and leaf carbon economics data. We aimed to investigate the variation of πtlp across biomes varying in water availability. We also tested two hypotheses: (i) πtlp predicts leaf hydraulic safety margins and (ii) it is correlated with leaf carbon economics traits. Our results showed that there was a positive relationship between πtlp and aridity index: biomes from humid regions had less negative values than those from arid regions. This supports the idea that πtlp may reflect drought tolerance at the scale of woody biomes. As expected, πtlp was significantly positively correlated with leaf hydraulic safety margins that varied significantly across biomes, indicating that this trait may be useful in modelling changes of forest components in response to increasing drought. Moreover, πtlp was correlated with a suite of coordinated hydraulic and economics traits; therefore, it can be used to predict the position of a given species along the 'fast-slow' whole-plant economics spectrum. This study expands our understanding of the biological significance of πtlp not only in drought tolerance, but also in the plant economics spectrum.

7 CFR 29.3528 - Leaf surface.

Science.gov (United States)

2010-01-01

... INSPECTION Standards Official Standard Grades for Dark Air-Cured Tobacco (u.s. Types 35, 36, 37 and Foreign Type 95) § 29.3528 Leaf surface. The roughness or smoothness of the web or lamina of a tobacco leaf...

Non-destructive measurement of soybean leaf thickness via X-ray computed tomography allows the study of diel leaf growth rhythms in the third dimension.

Science.gov (United States)

Pfeifer, Johannes; Mielewczik, Michael; Friedli, Michael; Kirchgessner, Norbert; Walter, Achim

2018-01-01

Present-day high-resolution leaf growth measurements provide exciting insights into diel (24-h) leaf growth rhythms and their control by the circadian clock, which match photosynthesis with oscillating environmental conditions. However, these methods are based on measurements of leaf area or elongation and neglect diel changes of leaf thickness. In contrast, the influence of various environmental stress factors to which leaves are exposed to during growth on the final leaf thickness has been studied extensively. Yet, these studies cannot elucidate how variation in leaf area and thickness are simultaneously regulated and influenced on smaller time scales. Only few methods are available to measure the thickness of young, growing leaves non-destructively. Therefore, we evaluated X-ray computed tomography to simultaneously and non-invasively record diel changes and growth of leaf thickness and area. Using conventional imaging and X-ray computed tomography leaf area, thickness and volume growth of young soybean leaves were simultaneously and non-destructively monitored at three cardinal time points during night and day for a period of 80 h under non-stressful growth conditions. Reference thickness measurements on paperboards were in good agreement to CT measurements. Comparison of CT with leaf mass data further proved the consistency of our method. Exploratory analysis showed that measurements were accurate enough for recording and analyzing relative diel changes of leaf thickness, which were considerably different to those of leaf area. Relative growth rates of leaf area were consistently positive and highest during 'nights', while diel changes in thickness fluctuated more and were temporarily negative, particularly during 'evenings'. The method is suitable for non-invasive, accurate monitoring of diel variation in leaf volume. Moreover, our results indicate that diel rhythms of leaf area and thickness show some similarity but are not tightly coupled. These

What Is a Leaf? An Online Tutorial and Tests

Science.gov (United States)

Burrows, Geoffrey

2008-01-01

A leaf is a fundamental unit in botany and understanding what constitutes a leaf is fundamental to many plant science activities. My observations and subsequent testing indicated that many students could not confidently and consistently recognise a leaf from a leaflet, or recognise basic leaf arrangements and the various types of compound or…

Modeling the leaf angle dynamics in rice plant.

Directory of Open Access Journals (Sweden)

Yonghui Zhang

Full Text Available The leaf angle between stem and sheath (SSA is an important rice morphological trait. The objective of this study was to develop and validate a dynamic SSA model under different nitrogen (N rates for selected rice cultivars. The time-course data of SSA were collected in three years, and a dynamic SSA model was developed for different main stem leaf ranks under different N rates for two selected rice cultivars. SSA increased with tiller age. The SSA of the same leaf rank increased with increase in N rate. The maximum SSA increased with leaf rank from the first to the third leaf, then decreased from the third to the final leaf. The relationship between the maximum SSA and leaf rank on main stem could be described with a linear piecewise function. The change of SSA with thermal time (TT was described by a logistic equation. A variety parameter (the maximum SSA of the 3rd leaf on main stem and a nitrogen factor were introduced to quantify the effect of cultivar and N rate on SSA. The model was validated against data collected from both pot and field experiments. The relative root mean square error (RRMSE was 11.56% and 14.05%, respectively. The resulting models could be used for virtual rice plant modeling and plant-type design.

Screening Study of Leaf Terpene Concentration of 75 Borneo Rainforest Plant Species: Relationships with Leaf Elemental Concentrations and Morphology

Directory of Open Access Journals (Sweden)

Jordi Sardans

2015-01-01

Full Text Available Terpenes confer advantage in plant protection against abiotic stresses such as heat and drought and biotic stresses such as herbivore and pathogen attack. We conducted a screening of leaf mono- and sesquiterpene concentrations in 75 common woody plant species in the rainforest of Danum Valley (Borneo. Terpene compounds were found in 73 out of the 75 analysed species. Similar or lower proportions have been reported in other parts of the world. To our knowledge, this study reports for the first time the foliar concentration of mono- and/or sesquiterpene for 71 species and 39 genera not previously analyzed. Altogether 80 terpene compounds were determined across the species, and out of these only linalool oxide and (E- g -bisabolene had phylogenetic signal. A significant negative relationship between leaf monoterpene concentration and leaf length was observed, but leaf mono- and sesquitepene concentration were not related to any other leaf morphological trait nor to leaf elemental composition. Functions such as temperature protection, radiation protection or signaling and communication could underlie the high frequency of terpene-containing species of this tropical ecosystem which has multiple and very diverse interactions among multiple species.

Measurement of Leaf Mass and Leaf Area of Oaks In A Mediterranean-climate Region For Biogenic Emission Estimation

Science.gov (United States)

Karlik, J.

Given the key role played by biogenic volatile organic compounds (BVOC) in tro- pospheric chemistry and regional air quality, it is critical to generate accurate BVOC emission inventories. Because several oak species have high BVOC emission rates, and oak trees are often of large stature with corresponding large leaf masses, oaks may be the most important genus of woody plants for BVOC emissions modeling in the natural landscapes of Mediterranean-climate regions. In California, BVOC emis- sions from oaks may mix with anthropogenic emissions from urban areas, leading to elevated levels of ozone. Data for leaf mass and leaf area for a stand of native blue oaks (Quercus douglasii) were obtained through harvest and leaf removal from 14 trees lo- cated in the Sierra Nevada foothills of central California. Trees ranged in height from 4.2 to 9.9 m, with trunk diameters at breast height of 14 to 85 cm. Mean leaf mass density was 730 g m-2 for the trees and had an overall value of 310 g m-2 for the site. Consideration of the surrounding grassland devoid of trees resulted in a value of about 150 g m-2, less than half of reported values for eastern U.S. oak woodlands, but close to a reported value for oaks found in St. Quercio, Italy. The mean value for leaf area index (LAI) for the trees at this site was 4.4 m2 m-2. LAI for the site was 1.8 m2 m-2, but this value was appropriate for the oak grove only; including the surrounding open grassland resulted in an overall LAI value of 0.9 m2 m-2 or less. A volumetric method worked well for estimating the leaf mass of the oak trees. Among allometric relationships investigated, trunk circumference, mean crown radius, and crown projec- tion were well correlated with leaf mass. Estimated emission of isoprene (mg C m-2 h-1) for the site based these leaf mass data and experimentally determined emission rate was similar to that reported for a Mediterranean oak woodland in France.

Leaf-jams - A new and unique leaf deposit in the ephemeral Hoanib River, NW Namibia: Origin and plant taphonomic implications

Energy Technology Data Exchange (ETDEWEB)

Hofmann, Christa-Ch. [University of Vienna, Department of Palaeontology, Palaeobotany Studies Group, Althanstrasse 14, 1090, Vienna (Austria); Rice, A. Hugh N. [University of Vienna, Department of Geodynamics and Sedimentology, Althanstrasse 14, 1090, Vienna (Austria)

2010-08-01

This paper documents a previously unrecorded type of leaf deposit, comprising essentially monospecific linear accumulations of Colophospermum mopane leaves on a point bar of the ephemeral Hoanib River, NW Namibia. In these 'leaf-jams', leaf laminae stand on edge, orientated more-or-less normal to bedding. Leaf-jams, which formed upstream of cobbles, clumps of grass and sticks wedged against the former two, were orientated subparallel to the adjacent meandering river-bed, such that over the 40 m of their occurrence, their mean azimuth changed by 59 anticlockwise downstream. The longest leaf-jam was 50 cm and contained approximately 500 leaves, as well as grass culms, twigs (C. mopane, Tamarix usneoides and unidentified) and medium- to fine-grained sand and silt. Individual leaf-jams were partially buried in the point bar sediments up to a depth of 3 cm. Leaf-jam formation occurred in the austral summer of 2006, during the waning stage of a major flood caused by anomalous tropical to extra-tropical storms. Their monospecifity is due to the overwhelming preponderance of the zonal taxon C. mopane in the catchment area, although the Khowarib Gorge contains a quite diverse azonal plant association due to the presence of a permanent water-seep. During leaf-jam formation, the water depth was less than the height of the cobbles (0.1 m), with stream flow-rates competent to transport medium-grained sand (velocity estimated at 0.5 m s{sup -} {sup 1}). Leaves must have been partially or fully waterlogged to inhibit buoyancy forces tending to lift them out of the developing leaf-jams, which propagated upstream in a manner comparable to longitudinal bars in a braided river. If fossilised, such deposits would probably lead to a very biased interpretation of the composition of the surrounding flora; the correct interpretation would be the one least favoured by palaeobotanists. (author)

Chromosome-damaging effect of betel leaf.

Science.gov (United States)

Sadasivan, G; Rani, G; Kumari, C K

1978-05-01

The chewing of betel leaf with other ingredients is a widespread addiction in India. The chromosome damaging effect was studied in human leukocyte cultures. There was an increase in the frequency of chromatid aberrations when the leaf extract was added to cultures.

Does leaf chemistry differentially affect breakdown in tropical vs temperate streams? Importance of standardized analytical techniques to measure leaf chemistry

Science.gov (United States)

Marcelo Ard& #243; n; Catherine M. Pringle; Susan L. Eggert

2009-01-01

Comparisons of the effects of leaf litter chemistry on leaf breakdown rates in tropical vs temperate streams are hindered by incompatibility among studies and across sites of analytical methods used to measure leaf chemistry. We used standardized analytical techniques to measure chemistry and breakdown rate of leaves from common riparian tree species at 2 sites, 1...

7 CFR 29.2277 - Leaf scrap.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.2277 Section 29.2277 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists...

Impact of anatomical traits of maize (Zea mays L.) leaf as affected by nitrogen supply and leaf age on bundle sheath conductance.

Science.gov (United States)

Retta, Moges; Yin, Xinyou; van der Putten, Peter E L; Cantre, Denis; Berghuijs, Herman N C; Ho, Quang Tri; Verboven, Pieter; Struik, Paul C; Nicolaï, Bart M

2016-11-01

The mechanism of photosynthesis in C 4 crops depends on the archetypal Kranz-anatomy. To examine how the leaf anatomy, as altered by nitrogen supply and leaf age, affects the bundle sheath conductance (g bs ), maize (Zea mays L.) plants were grown under three contrasting nitrogen levels. Combined gas exchange and chlorophyll fluorescence measurements were done on fully grown leaves at two leaf ages. The measured data were analysed using a biochemical model of C 4 photosynthesis to estimate g bs . The leaf microstructure and ultrastructure were quantified using images obtained from micro-computed tomography and microscopy. There was a strong positive correlation between g bs and leaf nitrogen content (LNC) while old leaves had lower g bs than young leaves. Leaf thickness, bundle sheath cell wall thickness and surface area of bundle sheath cells per unit leaf area (S b ) correlated well with g bs although they were not significantly affected by LNC. As a result, the increase of g bs with LNC was little explained by the alteration of leaf anatomy. In contrast, the combined effect of LNC and leaf age on S b was responsible for differences in g bs between young leaves and old leaves. Future investigations should consider changes at the level of plasmodesmata and membranes along the CO 2 leakage pathway to unravel LNC and age effects further. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Photoperiod-H1 (Ppd-H1) Controls Leaf Size1[OPEN

Science.gov (United States)

Digel, Benedikt; Tavakol, Elahe; Verderio, Gabriele; Xu, Xin

2016-01-01

Leaf size is a major determinant of plant photosynthetic activity and biomass; however, it is poorly understood how leaf size is genetically controlled in cereal crop plants like barley (Hordeum vulgare). We conducted a genome-wide association scan for flowering time, leaf width, and leaf length in a diverse panel of European winter cultivars grown in the field and genotyped with a single-nucleotide polymorphism array. The genome-wide association scan identified PHOTOPERIOD-H1 (Ppd-H1) as a candidate gene underlying the major quantitative trait loci for flowering time and leaf size in the barley population. Microscopic phenotyping of three independent introgression lines confirmed the effect of Ppd-H1 on leaf size. Differences in the duration of leaf growth and consequent variation in leaf cell number were responsible for the leaf size differences between the Ppd-H1 variants. The Ppd-H1-dependent induction of the BARLEY MADS BOX genes BM3 and BM8 in the leaf correlated with reductions in leaf size and leaf number. Our results indicate that leaf size is controlled by the Ppd-H1- and photoperiod-dependent progression of plant development. The coordination of leaf growth with flowering may be part of a reproductive strategy to optimize resource allocation to the developing inflorescences and seeds. PMID:27457126

Leaf wetness distribution within a potato crop

Science.gov (United States)

Heusinkveld, B. G.

2010-07-01

The Netherlands has a mild maritime climate and therefore the major interest in leaf wetness is associated with foliar plant diseases. During moist micrometeorological conditions (i.e. dew, fog, rain), foliar fungal diseases may develop quickly and thereby destroy a crop quickly. Potato crop monocultures covering several hectares are especially vulnerable to such diseases. Therefore understanding and predicting leaf wetness in potato crops is crucial in crop disease control strategies. A field experiment was carried out in a large homogeneous potato crop in the Netherlands during the growing season of 2008. Two innovative sensor networks were installed as a 3 by 3 grid at 3 heights covering an area of about 2 hectares within two larger potato crops. One crop was located on a sandy soil and one crop on a sandy peat soil. In most cases leaf wetting starts in the top layer and then progresses downward. Leaf drying takes place in the same order after sunrise. A canopy dew simulation model was applied to simulate spatial leaf wetness distribution. The dew model is based on an energy balance model. The model can be run using information on the above-canopy wind speed, air temperature, humidity, net radiation and within canopy air temperature, humidity and soil moisture content and temperature conditions. Rainfall was accounted for by applying an interception model. The results of the dew model agreed well with the leaf wetness sensors if all local conditions were considered. The measurements show that the spatial correlation of leaf wetness decreases downward.

Foraging on individual leaves by an intracellular feeding insect is not associated with leaf biomechanical properties or leaf orientation.

Directory of Open Access Journals (Sweden)

Justin Fiene

Full Text Available Nearly all herbivorous arthropods make foraging-decisions on individual leaves, yet systematic investigations of the adaptive significance and ecological factors structuring these decisions are rare with most attention given to chewing herbivores. This study investigated why an intracellular feeding herbivore, Western flower thrips (WFT Frankliniella occidentalis Pergande, generally avoids feeding on the adaxial leaf surface of cotton cotyledons. WFT showed a significant aversion to adaxial-feeding even when excised-cotyledons were turned up-side (abaxial-side 'up', suggesting that negative-phototaxis was not a primary cause of thrips foraging patterns. No-choice bioassays in which individual WFT females were confined to either the abaxial or adaxial leaf surface showed that 35% fewer offspring were produced when only adaxial feeding was allowed, which coincided with 32% less plant feeding on that surface. To test the hypothesis that leaf biomechanical properties inhibited thrips feeding on the adaxial surface, we used a penetrometer to measure two variables related to the 'toughness' of each leaf surface. Neither variable negatively co-varied with feeding. Thus, while avoiding the upper leaf surface was an adaptive foraging strategy, the proximate cause remains to be elucidated, but is likely due, in part, to certain leaf properties that inhibit feeding.

7 CFR 29.2278 - Leaf structure.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf structure. 29.2278 Section 29.2278 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... structure. The cell development of a leaf as indicated by its porosity. (See chart, § 29.2351.) ...

7 CFR 29.2529 - Leaf scrap.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.2529 Section 29.2529 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or...

Inheritance of okra leaf type in different genetic backgrounds and its ...

African Journals Online (AJOL)

use

2011-11-21

Nov 21, 2011 ... discontinuous variation for leaf shape in F2 generations of three crosses .... Variable classes in leaf types (a) Normal leaf (b) Okra leaf (c) Sub-okra leaf. ..... insect pests on different isogenic lines of cotton variety H-777. J.

Waiting for the Leaf; Warten auf den Leaf

Energy Technology Data Exchange (ETDEWEB)

Wilms, Jan

2012-01-15

Nissan will be the first manufacturer to launch an electric vehicle of the VW Golf category in the German market. With a mileage of about 170 km and a roomy passenger compartment, the Leaf promises much comfort. In the US market, it was launched two years ago. Was it worth while waiting for?.

From leaf to whole-plant water use efficiency (WUE in complex canopies: Limitations of leaf WUE as a selection target

Directory of Open Access Journals (Sweden)

Hipólito Medrano

2015-06-01

Full Text Available Plant water use efficiency (WUE is becoming a key issue in semiarid areas, where crop production relies on the use of large volumes of water. Improving WUE is necessary for securing environmental sustainability of food production in these areas. Given that climate change predictions include increases in temperature and drought in semiarid regions, improving crop WUE is mandatory for global food production. WUE is commonly measured at the leaf level, because portable equipment for measuring leaf gas exchange rates facilitates the simultaneous measurement of photosynthesis and transpiration. However, when those measurements are compared with daily integrals or whole-plant estimates of WUE, the two sometimes do not agree. Scaling up from single-leaf to whole-plant WUE was tested in grapevines in different experiments by comparison of daily integrals of instantaneous water use efficiency [ratio between CO2 assimilation (AN and transpiration (E; AN/E] with midday AN/E measurements, showing a low correlation, being worse with increasing water stress. We sought to evaluate the importance of spatial and temporal variation in carbon and water balances at the leaf and plant levels. The leaf position (governing average light interception in the canopy showed a marked effect on instantaneous and daily integrals of leaf WUE. Night transpiration and respiration rates were also evaluated, as well as respiration contributions to total carbon balance. Two main components were identified as filling the gap between leaf and whole plant WUE: the large effect of leaf position on daily carbon gain and water loss and the large flux of carbon losses by dark respiration. These results show that WUE evaluation among genotypes or treatments needs to be revised.

A finger leaf design for dual layer MLCs

International Nuclear Information System (INIS)

Cui Weijie; Dai Jianrong

2010-01-01

Objective: To introduce a finger leaf design that is applied to dual layer MLCs. Methods: An optimization model was firstly constructed to describe the problem of determining leaf end shapes,and the corresponding problems were then solved by the simplex search method or the simulated annealing technique. Optimal parameters for arc shapes of leaf end projections were obtained, and a comparison was done between optimized MLCs and conventional MLCs in terms of field conformity. The optimization process was based on 634 target fields selected from the patient data base of a treatment planning system. Areas of these fields ranged from 20.0 to 602.7 cm with a mean and its standard deviation of (125.7 ± 0.0) cm 2 . Results: The optimized leaf end shapes projected to the isocenter plane were semicircles. With the finger leaf design, the total area of discrepancy regions between MLC fields and target fields was reduced by 32.3%. Conclusions: The finger leaf design improves the conformity of the MLC shaped fields to the desired target fields. (authors)

Leaf Wetness within a Lily Canopy

NARCIS (Netherlands)

Jacobs, A.F.G.; Heusinkveld, B.G.; Klok, E.J.

2005-01-01

A wetness duration experiment was carried out within a lily field situated adjacent to coastal dunes in the Netherlands. A within-canopy model was applied to simulate leaf wetness in three layers, with equal leaf area indices, within the canopy. This simulation model is an extension of an existing

How Does Temperature Impact Leaf Size and Shape in Four Woody Dicot Species? Testing the Assumptions of Leaf Physiognomy-Climate Models

Science.gov (United States)

McKee, M.; Royer, D. L.

2017-12-01

The physiognomy (size and shape) of fossilized leaves has been used to reconstruct the mean annual temperature of ancient environments. Colder temperatures often select for larger and more abundant leaf teeth—serrated edges on leaf margins—as well as a greater degree of leaf dissection. However, to be able to accurately predict paleotemperature from the morphology of fossilized leaves, leaves must be able to react quickly and in a predictable manner to changes in temperature. We examined the extent to which temperature affects leaf morphology in four tree species: Carpinus caroliniana, Acer negundo, Ilex opaca, and Ostrya virginiana. Saplings of these species were grown in two growth cabinets under contrasting temperatures (17 and 25 °C). Compared to the cool treatment, in the warm treatment Carpinus caroliniana leaves had significantly fewer leaf teeth and a lower ratio of total number of leaf teeth to internal perimeter; and Acer negundo leaves had a significantly lower feret diameter ratio (a measure of leaf dissection). In addition, a two-way ANOVA tested the influence of temperature and species on leaf physiognomy. This analysis revealed that all plants, regardless of species, tended to develop more highly dissected leaves with more leaf teeth in the cool treatment. Because the cabinets maintained equivalent moisture, humidity, and CO2 concentration between the two treatments, these results demonstrate that these species could rapidly adapt to changes in temperature. However, not all of the species reacted identically to temperature changes. For example, Acer negundo, Carpinus caroliniana, and Ostrya virginiana all had a higher number of total teeth in the cool treatment compared to the warm treatment, but the opposite was true for Ilex opaca. Our work questions a fundamental assumption common to all models predicting paleotemperature from the physiognomy of fossilized leaves: a given climate will inevitably select for the same leaf physiognomy

7 CFR 29.2530 - Leaf structure.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf structure. 29.2530 Section 29.2530 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing...-Cured Tobacco (u.s. Types 22, 23, and Foreign Type 96) § 29.2530 Leaf structure. The cell development of...

Importance of Secondary Metabolites for Leaf Beetles (Coleoptera: Chrysomelidae

Directory of Open Access Journals (Sweden)

A. N. EKİZ

2014-06-01

Full Text Available Leaf beetles (Chrysomelidae are one of the most diverse families of herbivorous insects. Many of them are important agricultural pests and cause remarkable loss of crop and money as well. Plant leaves and roots are primary food source of both larva and adults of leaf beetles. Plants produce many secondary metabolites in reaction to herbivore insects. It is a well-known phenomenon that quantity and variety of secondary metabolites in plant leaves may change in response to insect attacks. Herbivore insects have to deal with such defensive secondary chemicals and overcome either by detoxifying or storing them. Accordingly, many specialist herbivores coevolved with their host plant. Certain phenolic glycosides may reduce leaf beetle feeding. Condensed tannins are anti-herbivore defenses against leaf chewing beetles, including leaf beetles. Flavonoid compounds are feeding deterrents for many flea leaf beetles. Cinnamic acid derivatives are other known feeding deterrents for leaf beetles. Secondary metabolites quantity and nutritional quality of host plants are not only important for feeding but also for providing enemy-free space and suitable oviposition sites.

Models for leaf area estimation in dwarf pigeon pea by leaf dimensions

Directory of Open Access Journals (Sweden)

Rafael Vieira Pezzini

2018-03-01

Full Text Available ABSTRACT This study aims to determine the most suitable model to estimate the leaf area of dwarf pigeon pea in function of the leaf central leaflet dimension. Six samplings of 200 leaves were performed in the first experiment, at 36, 42, 50, 56, 64, and 72 days after emergence (DAE. In the second experiment, seven samplings of 200 leaves were performed at 29, 36, 43, 49, 57, 65, and 70 DAE, totaling 2600 leaves. The length (L and width (W of the central leaflet were measured in all leaves composed by left, central, and right leaflets, the product of length times width (LW was calculated, and the leaf area (Y – sum of left, central, and right leaflet areas was determined by digital images. Linear, power, quadratic, and cubic models of Y as function of L, W, and LW were built using data from the second experiment. Leaves from the first experiment were used to validate the models. In dwarf pigeon pea, the linear (Ŷ = – 0.4088 + 1.6669x, R2 = 0.9790 is preferable, but power (Ŷ = 1.6097x1.0065, R2 = 0.9766, quadratic (Ŷ = – 0.3625 + 1.663x + 0.00007x2, R2 = 0.9790, and cubic (Ŷ = 0.7216 + 1.522x + 0.005x2 – 5E–05x3, R2 = 0.9791 models in function of LW are also suitable to estimate the leaf area obtained by digital images. The power model (Ŷ = 5.2508x1.7868, R2 = 0.95 based on the central leaflet width is less laborious because requires only one variable, but it presents accuracy reduction.

Leveraging multiple datasets for deep leaf counting

OpenAIRE

Dobrescu, Andrei; Giuffrida, Mario Valerio; Tsaftaris, Sotirios A

2017-01-01

The number of leaves a plant has is one of the key traits (phenotypes) describing its development and growth. Here, we propose an automated, deep learning based approach for counting leaves in model rosette plants. While state-of-the-art results on leaf counting with deep learning methods have recently been reported, they obtain the count as a result of leaf segmentation and thus require per-leaf (instance) segmentation to train the models (a rather strong annotation). Instead, our method tre...

Resistance in winter barley against Ramularia leaf spot

DEFF Research Database (Denmark)

Hjortshøj, Rasmus Lund

Ramularia leaf spot is an emerging disease in barley caused by R. collo-cygni. At present little is known about the resistance mechanisms carried out by the host plant to avoid disease development. Nor is the lifecycle of the fungus or its populations structure fully understood. To gain insight....... fulvum-tomato and S. tritici-wheat in order to find modelsystems to enhance interpretation of results from R. collo-cygni-barley interaction. Results from the mapping showed that resistance to Ramularia leaf spot is controlled by a number of QTL’s, some of which co-locate with other physiological traits....... The populations further segregated for physiological leaf spots, a phenomenon related to the leaf damage imposed by Rubellin, although, resistance to physiological leafspots appeared to come from the Ramularia leaf spot susceptible parent. The toxin assay further supported this result as the genotypes susceptible...

[Latitude variation mechanism of leaf traits of Metasequoia glyptostroboides in eastern coastal China].

Science.gov (United States)

Guo, Wei Hong; Wang, Hua; Yu, Mu Kui; Wu, Tong Gui; Han, You Zhi

2017-03-18

We analyzed the rules of Metasequoia glyptostroboides along with latitude, including leaf length, leaf width, leaf perimeter, leaf area, ratio of leaf length to width, specific leaf area (SLA), and leaf dry mass based on eight stands growing at different latitudes in the coastal area of eastern China, as well as their relationships with climatic and soil factors. The results showed that the leaf length, leaf width and leaf perimeter increased with increasing latitude, while the leaf area and SLA firstly increased and then decreased. The mean annual temperature and annual precipitation were the major environmental factors affecting the leaf traits along latitude gradient. With the increase of soil N content, the SLA decreased firstly and then increased, while the leaf mass decreased significantly. With the increase of soil P content, the SLA increased, and the leaf mass decreased significantly.

Endophytic fungi reduce leaf-cutting ant damage to seedlings

Science.gov (United States)

Bittleston, L. S.; Brockmann, F.; Wcislo, W.; Van Bael, S. A.

2011-01-01

Our study examines how the mutualism between Atta colombica leaf-cutting ants and their cultivated fungus is influenced by the presence of diverse foliar endophytic fungi (endophytes) at high densities in tropical leaf tissues. We conducted laboratory choice trials in which ant colonies chose between Cordia alliodora seedlings with high (Ehigh) or low (Elow) densities of endophytes. The Ehigh seedlings contained 5.5 times higher endophyte content and a greater diversity of fungal morphospecies than the Elow treatment, and endophyte content was not correlated with leaf toughness or thickness. Leaf-cutting ants cut over 2.5 times the leaf area from Elow relative to Ehigh seedlings and had a tendency to recruit more ants to Elow plants. Our findings suggest that leaf-cutting ants may incur costs from cutting and processing leaves with high endophyte loads, which could impact Neotropical forests by causing variable damage rates within plant communities. PMID:20610420

Consequences of leaf calibration errors on IMRT delivery

International Nuclear Information System (INIS)

Sastre-Padro, M; Welleweerd, J; Malinen, E; Eilertsen, K; Olsen, D R; Heide, U A van der

2007-01-01

IMRT treatments using multi-leaf collimators may involve a large number of segments in order to spare the organs at risk. When a large proportion of these segments are small, leaf positioning errors may become relevant and have therapeutic consequences. The performance of four head and neck IMRT treatments under eight different cases of leaf positioning errors has been studied. Systematic leaf pair offset errors in the range of ±2.0 mm were introduced, thus modifying the segment sizes of the original IMRT plans. Thirty-six films were irradiated with the original and modified segments. The dose difference and the gamma index (with 2%/2 mm criteria) were used for evaluating the discrepancies between the irradiated films. The median dose differences were linearly related to the simulated leaf pair errors. In the worst case, a 2.0 mm error generated a median dose difference of 1.5%. Following the gamma analysis, two out of the 32 modified plans were not acceptable. In conclusion, small systematic leaf bank positioning errors have a measurable impact on the delivered dose and may have consequences for the therapeutic outcome of IMRT

Generality of leaf trait relationships: A test across six biomes

Energy Technology Data Exchange (ETDEWEB)

Reich, P.B. [Univ. of Minnesota, Saint Paul, MN (United States). Dept. of Forest Resources; Ellsworth, D.S. [Brookhaven National Lab., Upton, NY (United States). Dept. of Applied Science; Walters, M.B. [Michigan State Univ., East Lansing, MI (United States). Dept. of Forestry; Vose, J.M. [Forest Service, Otto, NC (United States). Coweeta Hydrological Lab.; Gresham, C. [Clemson Univ., Georgetown, SC (United States). Baruch Forest Inst.; Volin, J.C. [Florida Atlantic Univ., Davie, FL (United States). Div. of Science; Bowman, W.D. [Inst. of Arctic and Alpine Research, Boulder, CO (United States). Mountain Research Station]|[Univ. of Colorado, Boulder, CO (United States). Dept. of Evolutionary, Population, and Organismic Biology

1999-09-01

Convergence in interspecific leaf trait relationships across diverse taxonomic groups and biomes would have important evolutionary and ecological implications. Such convergence has been hypothesized to result from trade-offs that limit the combination of plant traits for any species. Here the authors address this issue by testing for biome differences in the slope and intercept of interspecific relationships among leaf traits: longevity, net photosynthetic capacity (A{sub max}), leaf diffusive conductance (G{sub S}), specific leaf area (SLA), and nitrogen (N) status, for more than 100 species in six distinct biomes of the Americas. The six biomes were: alpine tundra-subalpine forest ecotone, cold temperate forest-prairie ecotone, montane cool temperate forest, desert shrubland, subtropical forest, and tropical rain forest. Despite large differences in climate and evolutionary history, in all biomes mass-based leaf N (N{sub mass}), SLA, G{sub S}, and A{sub max} were positively related to one another and decreased with increasing leaf life span. The relationships between pairs of leaf traits exhibited similar slopes among biomes, suggesting a predictable set of scaling relationships among key leaf morphological, chemical, and metabolic traits that are replicated globally among terrestrial ecosystems regardless of biome or vegetation type. However, the intercept (i.e., the overall elevation of regression lines) of relationships between pairs of leaf traits usually differed among biomes. With increasing aridity across sites, species had greater A{sub max} for a given level of G{sub S} and lower SLA for any given leaf life span. Using principal components analysis, most variation among species was explained by an axis related to mass-based leaf traits (A{sub max}, N, and SLA) while a second axis reflected climate, G{sub S}, and other area-based leaf traits.

Effects of some growth regulating applications on leaf yield, raw ...

African Journals Online (AJOL)

This study investigated the effects of repetitive applications of herbagreen (HG), humic acid (HA), combined foliar fertilizer (CFF) and HG+CFF performed in the Müsküle grape variety grafted on 5 BB rootstock on fresh or pickled leaf size and leaf raw cellulose content. HA application increased leaf area and leaf water ...

Patterns of leaf morphology and leaf N content in relation to winter temperatures in three evergreen tree species

Science.gov (United States)

Mediavilla, Sonia; Gallardo-López, Victoria; González-Zurdo, Patricia; Escudero, Alfonso

2012-09-01

The competitive equilibrium between deciduous and perennial species in a new scenario of climate change may depend closely on the productivity of leaves along the different seasons of the year and on the morphological and chemical adaptations required for leaf survival during the different seasons. The aim of the present work was to analyze such adaptations in the leaves of three evergreen species ( Quercus ilex, Q. suber and Pinus pinaster) and their responses to between-site differences in the intensity of winter harshness. We explore the hypothesis that the harshness of winter would contribute to enhancing the leaf traits that allow them to persist under conditions of stress. The results revealed that as winter harshness increases a decrease in leaf size occurs in all three species, together with an increase in the content of nitrogen per unit leaf area and a greater leaf mass per unit area, which seems to be achieved only through increased thickness, with no associated changes in density. P. pinaster was the species with the most intense response to the harshening of winter conditions, undergoing a more marked thickening of its needles than the two Quercus species. Our findings thus suggest that lower winter temperatures involve an increase in the cost of leaf production of evergreen species, which must be taken into account in the estimation of the final cost and benefit balance of evergreens. Such cost increases would be more pronounced for those species that, like P. pinaster, show a stronger response to the winter cold.

Dynamics of vacuum-sealed, double-leaf partitions

Science.gov (United States)

Kavanaugh, Joshua Stephen

The goal of this research is to investigate the feasibility and potential effectiveness of using vacuum-sealed, double-leaf partitions for applications in noise control. Substantial work has been done previously on double-leaf partitions where the acoustics of the inner chamber and mechanical vibrations of structural supports are passively and actively controlled. The work presented here is unique in that the proposed system aims to eliminate the need for active acoustic control of transmitted acoustic energy by removing all the air between the two panels of the double partition. Therefore, the only remaining energy paths would be along the boundary and at the points where there are intermediate structural supports connecting the two panels. The eventual goal of the research is to develop a high-loss double-leaf partition that simplifies active control by removing the need for control of the air cavity and channeling all the energy into discrete structural paths. The work presented here is a first step towards the goal of designing a high-loss, actively-controlled double-leaf partition with an air-evacuated inner chamber. One experiment is conducted to investigate the effects of various levels of vacuum on the response of a double-leaf partition whose panels are mechanically coupled only at the boundary. Another experiment is conducted which investigates the effect of changing the stiffness of an intermediate support coupling the two panels of a double-leaf partition in which a vacuum has been applied to the inner cavity. The available equipment was able to maintain a 99% vacuum between the panels. Both experiments are accompanied by analytical models used to investigate the importance of various dynamic parameters. Results show that the vacuum-sealed system shows some potential for increased transmission loss, primarily by the changing the natural frequencies of the double-leaf partition.

Predicting tropical plant physiology from leaf and canopy spectroscopy.

Science.gov (United States)

Doughty, Christopher E; Asner, Gregory P; Martin, Roberta E

2011-02-01

A broad regional understanding of tropical forest leaf photosynthesis has long been a goal for tropical forest ecologists, but it has remained elusive due to difficult canopy access and high species diversity. Here we develop an empirical model to predict sunlit, light-saturated, tropical leaf photosynthesis using leaf and simulated canopy spectra. To develop this model, we used partial least squares (PLS) analysis on three tropical forest datasets (159 species), two in Hawaii and one at the biosphere 2 laboratory (B2L). For each species, we measured light-saturated photosynthesis (A), light and CO(2) saturated photosynthesis (A(max)), respiration (R), leaf transmittance and reflectance spectra (400-2,500 nm), leaf nitrogen, chlorophyll a and b, carotenoids, and leaf mass per area (LMA). The model best predicted A [r(2) = 0.74, root mean square error (RMSE) = 2.9 μmol m(-2) s(-1))] followed by R (r(2) = 0.48), and A(max) (r(2) = 0.47). We combined leaf reflectance and transmittance with a canopy radiative transfer model to simulate top-of-canopy reflectance and found that canopy spectra are a better predictor of A (RMSE = 2.5 ± 0.07 μmol m(-2) s(-1)) than are leaf spectra. The results indicate the potential for this technique to be used with high-fidelity imaging spectrometers to remotely sense tropical forest canopy photosynthesis.

The Effect of Leaf Stacking on Leaf Reflectance and Vegetation Indices Measured by Contact Probe during the Season

Czech Academy of Sciences Publication Activity Database

Neuwirthová, E.; Lhotáková, Z.; Albrechtová, Jana

2017-01-01

Roč. 17, č. 6 (2017), s. 1-23, č. článku 1202. ISSN 1424-8220 Institutional support: RVO:67985939 Keywords : broadleaved trees * leaf optical properties * leaf traits Subject RIV: EF - Botanics OBOR OECD: Plant sciences, botany Impact factor: 2.677, year: 2016

BOREAS TE-9 NSA Leaf Chlorophyll Density

Science.gov (United States)

Hall, Forrest G. (Editor); Curd, Shelaine (Editor); Margolis, Hank; Sy, Mikailou

2000-01-01

The BOREAS TE-9 team collected several data sets related to chemical and photosynthetic properties of leaves in boreal forest tree species. These data were collected to help provide an explanation of potential seasonal and spatial changes of leaf pigment properties in boreal forest species at the NSA. At different dates (FFC-Winter, FFC-Thaw, IFC-1, IFC-2, and IMC-3), foliage samples were collected from the upper third of the canopy for five NSA sites (YJP, OJP, OBS, UBS, and OA) near Thompson, Manitoba. Subsamples of 100 needles for black spruce, 20 needles for jack pine, and single leaf for trembling aspen were cut into pieces and immersed in a 20-mL DMF aliquot in a Nalgene test tube. The extracted foliage materials were then oven-dried at 68 C for 48 hours and weighed. Extracted leaf dry weight was converted to a total leaf area basis to express the chlorophyll content in mg/sq cm of total leaf area. The data are provided in tabular ASCII files. The data files are available on a CD-ROM (see document number 20010000884), or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Silver nano fabrication using leaf disc of Passiflora foetida Linn

Science.gov (United States)

Lade, Bipin D.; Patil, Anita S.

2017-06-01

The main purpose of the experiment is to develop a greener low cost SNP fabrication steps using factories of secondary metabolites from Passiflora leaf extract. Here, the leaf extraction process is omitted, and instead a leaf disc was used for stable SNP fabricated by optimizing parameters such as a circular leaf disc of 2 cm (1, 2, 3, 4, 5) instead of leaf extract and grade of pH (7, 8, 9, 11). The SNP synthesis reaction is tried under room temperature, sun, UV and dark condition. The leaf disc preparation steps are also discussed in details. The SNP obtained using (1 mM: 100 ml AgNO3+ singular leaf disc: pH 9, 11) is applied against featured room temperature and sun condition. The UV spectroscopic analysis confirms that sun rays synthesized SNP yields stable nano particles. The FTIR analysis confirms a large number of functional groups such as alkanes, alkyne, amines, aliphatic amine, carboxylic acid; nitro-compound, alcohol, saturated aldehyde and phenols involved in reduction of silver salt to zero valent ions. The leaf disc mediated synthesis of silver nanoparticles, minimizes leaf extract preparation step and eligible for stable SNP synthesis. The methods sun and room temperature based nano particles synthesized within 10 min would be use certainly for antimicrobial activity.

Reading the Leaves: A Comparison of Leaf Rank and Automated Areole Measurement for Quantifying Aspects of Leaf Venation

Directory of Open Access Journals (Sweden)

Walton A. Green

2014-08-01

Full Text Available The reticulate venation that is characteristic of a dicot leaf has excited interest from systematists for more than a century, and from physiological and developmental botanists for decades. The tools of digital image acquisition and computer image analysis, however, are only now approaching the sophistication needed to quantify aspects of the venation network found in real leaves quickly, easily, accurately, and reliably enough to produce biologically meaningful data. In this paper, we examine 120 leaves distributed across vascular plants (representing 118 genera and 80 families using two approaches: a semiquantitative scoring system called “leaf ranking,” devised by the late Leo Hickey, and an automated image-analysis protocol. In the process of comparing these approaches, we review some methodological issues that arise in trying to quantify a vein network, and discuss the strengths and weaknesses of automatic data collection and human pattern recognition. We conclude that subjective leaf rank provides a relatively consistent, semiquantitative measure of areole size among other variables; that modal areole size is generally consistent across large sections of a leaf lamina; and that both approaches—semiquantitative, subjective scoring; and fully quantitative, automated measurement—have appropriate places in the study of leaf venation.

Up-scaling of water use efficiency from leaf to canopy as based on leaf gas exchange relationships and the modeled in-canopy light distribution

DEFF Research Database (Denmark)

Linderson, Maj-Lena; Mikkelsen, Teis Nørgaard; Ibrom, Andreas

2012-01-01

The aim of this study was to evaluate the extent to which water use efficiency (WUE) at leaf scale can be used to assess WUE at canopy scale, leaf WUE being assumed to be a constant function of vapor pressure deficit and to thus not be dependent upon other environmental factors or varying leaf...... properties. Leaf WUE and its variability and dependencies were assessed using leafgas-exchange measurements obtained during two growing seasons, 1999 and 2000, at the Soroe beech forest study site on Zealand in Denmark. It was found that the VPD-normalized leaf WUE, WUEnormleaf, although dependent...

Betel leaf in stoma care.

Science.gov (United States)

Banu, Tahmina; Talukder, Rupom; Chowdhury, Tanvir Kabir; Hoque, Mozammel

2007-07-01

Construction of a stoma is a common procedure in pediatric surgical practice. For care of these stomas, commercially available devices such as ostomy bag, either disposable or of longer duration are usually used. These are expensive, particularly in countries like Bangladesh, and proper-sized ones are not always available. We have found an alternative for stoma care, betel leaf, which is suitable for Bangladeshis. We report the outcome of its use. After construction of stoma, at first zinc oxide paste was applied on the peristomal skin. A betel leaf with shiny, smooth surface outwards and rough surface inwards was put over the stoma with a hole made in the center according to the size of stoma. Another intact leaf covers the stomal opening. When bowel movement occurs, the overlying intact leaf was removed and the fecal matter was washed away from both. The leaves were reused after cleaning. Leaves were changed every 2 to 3 days. From June 1998 to December 2005, in the department of pediatric surgery, Chittagong Medical College and Hospital, Chittagong, Bangladesh, a total of 623 patients had exteriorization of bowel. Of this total, 495 stomas were cared for with betel leaves and 128 with ostomy bags. Of 623 children, 287 had sigmoid colostomy, 211 had transverse colostomy, 105 had ileostomy, and 20 had jejunostomy. Of the 495 children under betel leaf stoma care, 13 patients (2.6%) developed skin excoriation. There were no allergic reactions. Of the 128 patients using ostomy bag, 52 (40.65%) had skin excoriation. Twenty-four (18.75%) children developed some allergic reactions to adhesive. Monthly costs for betel leaves were 15 cents (10 BDT), whereas ostomy bags cost about US$24. In the care of stoma, betel leaves are cheap, easy to handle, nonirritant, and nonallergic.

Method for continuous measurement of export from a leaf

International Nuclear Information System (INIS)

Geiger, D.R.; Fondy, B.R.

1979-01-01

Export of labeled material derived by continuous photosynthesis in 14 CO 2 was monitored with a Geiger-Mueller detector positioned next to an exporting leaf blade. Rate of export of labeled material was calculated from the difference between rates of retention and net photosynthesis of labeled carbon for the observed leaf. Given certain conditions, including nearly constant distribution of labeled material among minor veins and various types of cells, count rate data for the source leaf can be coverted to rate of export of carbon. Changes in counting efficiency resulting from changes in leaf water status can be corrected for with data from a transducer which measures leaf thickness. Export data agreed with data obtained by monitoring the arrival of 14 C in the sink region; isolated leaves gave values near zero for export of labeled carbon from a given leaf on an intact plant. The technique detects changes in export with a resolution of 10 to 20 minutes

The influence of leaf anatomy on the internal light environment and photosynthetic electron transport rate: exploration with a new leaf ray tracing model.

Science.gov (United States)

Xiao, Yi; Tholen, Danny; Zhu, Xin-Guang

2016-11-01

Leaf photosynthesis is determined by biochemical properties and anatomical features. Here we developed a three-dimensional leaf model that can be used to evaluate the internal light environment of a leaf and its implications for whole-leaf electron transport rates (J). This model includes (i) the basic components of a leaf, such as the epidermis, palisade and spongy tissues, as well as the physical dimensions and arrangements of cell walls, vacuoles and chloroplasts; and (ii) an efficient forward ray-tracing algorithm, predicting the internal light environment for light of wavelengths between 400 and 2500nm. We studied the influence of leaf anatomy and ambient light on internal light conditions and J The results show that (i) different chloroplasts can experience drastically different light conditions, even when they are located at the same distance from the leaf surface; (ii) bundle sheath extensions, which are strips of parenchyma, collenchyma or sclerenchyma cells connecting the vascular bundles with the epidermis, can influence photosynthetic light-use efficiency of leaves; and (iii) chloroplast positioning can also influence the light-use efficiency of leaves. Mechanisms underlying leaf internal light heterogeneity and implications of the heterogeneity for photoprotection and for the convexity of the light response curves are discussed. © The Author 2016. Published by Oxford University Press on behalf of the Society for Experimental Biology.

ANXIOLYTIC ACTIVITY OF OCIMUM SANCTUM LEAF EXTRACT

OpenAIRE

Chattopadhyay, R.R.

1994-01-01

The anxiolytic activity of Ocimum sanctum leaf extract was studied in mice. O.sanctum leaf extract produced significant anxiolytic activity in plus – maze and open field behaviour test models. The effect was compared with diazepam, a standard antianxiety drug.

[Seasonal differences in the leaf hydraulic conductance of mature Acacia mangium in response to its leaf water use and photosynthesis].

Science.gov (United States)

Zhao, Ping; Sun, Gu-Chou; Ni, Guang-Yan; Zeng, Xiao-Ping

2013-01-01

In this study, measurements were made on the leaf water potential (psi1), stomatal conductance (g(s)), transpiration rate, leaf area index, and sapwood area of mature Acacia mangium, aimed to understand the relationships of the leaf hydraulic conductance (K1) with the leaf water use and photosynthetic characteristics of the A. mangium in wet season (May) and dry season (November). The ratio of sapwood area to leaf area (A(sp)/A(cl)) of the larger trees with an average height of 20 m and a diameter at breast height (DBH) of 0.26 m was 8.5% higher than that of the smaller trees with an average height of 14.5 m and a DBH of 0.19 m, suggesting that the larger trees had a higher water flux in their leaf xylem, which facilitated the water use of canopy leaf. The analysis on the vulnerability curve of the xylem showed that when the K1 decreased by 50%, the psi1 in wet season and dry season was -1.41 and -1.55 MPa, respectively, and the vulnerability of the xylem cavitation was higher in dry season than in wet season. The K1 peak value in wet season and dry season was 5.5 and 4.5 mmol x m(-2) x s(-1) x MPa(-1), and the maximum transpiration rate (T(r max)) was 3.6 and 1.8 mmol x m(-2) x s(-1), respectively. Both the K1 and T(r max), were obviously higher in wet season than in dry season. Within a day, the K1 and T(r), fluctuated many times, reflecting the reciprocated cycle of the xylem cavitation and refilling. The leaf stomatal closure occurred when the K1 declined over 50% or the psi1 reached -1.6 MPa. The g(s) would be maintained at a high level till the K1 declined over 50%. The correlation between the hydraulic conductance and photosynthetic rate was more significant in dry season than in wet season. The loss of leaf hydraulic conductance induced by seasonal change could be the causes of the decrease of T(r) and CO2 gas exchange.

Understanding of Leaf Development—the Science of Complexity

Directory of Open Access Journals (Sweden)

Robert Malinowski

2013-06-01

Full Text Available The leaf is the major organ involved in light perception and conversion of solar energy into organic carbon. In order to adapt to different natural habitats, plants have developed a variety of leaf forms, ranging from simple to compound, with various forms of dissection. Due to the enormous cellular complexity of leaves, understanding the mechanisms regulating development of these organs is difficult. In recent years there has been a dramatic increase in the use of technically advanced imaging techniques and computational modeling in studies of leaf development. Additionally, molecular tools for manipulation of morphogenesis were successfully used for in planta verification of developmental models. Results of these interdisciplinary studies show that global growth patterns influencing final leaf form are generated by cooperative action of genetic, biochemical, and biomechanical inputs. This review summarizes recent progress in integrative studies on leaf development and illustrates how intrinsic features of leaves (including their cellular complexity influence the choice of experimental approach.

Does leaf chemistry differentially affect breakdown in tropical versus temperate streams? Importance of standardized analytical techniques to measure leaf chemistry

Science.gov (United States)

Marcelo Ardon; Catherine M. Pringle; Susan L. Eggert

2009-01-01

Comparisons of the effects of leaf litter chemistry on leaf breakdown rates in tropical vs temperate streams are hindered by incompatibility among studies and across sites of analytical methods used to...

The effect of air pollution and other environmental stressors on leaf fluctuating asymmetry and specific leaf area of Salix alba L

Energy Technology Data Exchange (ETDEWEB)

Wuytack, Tatiana, E-mail: tatiana.wuytack@ua.ac.be [Department of Bioscience Engineering, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium); Wuyts, Karen, E-mail: karen.wuyts@ugent.be [Department of Bioscience Engineering, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium); Laboratory of Forestry, Department of Forest and Water Management, Ghent University, Geraardsbergsesteenweg 267, B-9090 Gontrode (Melle) (Belgium); Van Dongen, Stefan, E-mail: stefan.vandongen@ua.ac.be [Department of Biology, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium); Baeten, Lander, E-mail: lander.baeten@ugent.be [Laboratory of Forestry, Department of Forest and Water Management, Ghent University, Geraardsbergsesteenweg 267, B-9090 Gontrode (Melle) (Belgium); Kardel, Fatemeh, E-mail: fatemeh.kardel@ua.ac.be [Department of Bioscience Engineering, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium); Verheyen, Kris, E-mail: kris.verheyen@ugent.be [Laboratory of Forestry, Department of Forest and Water Management, Ghent University, Geraardsbergsesteenweg 267, B-9090 Gontrode, Melle (Belgium); Samson, Roeland, E-mail: roeland.samson@ua.ac.be [Department of Bioscience Engineering, University of Antwerp, Groenenborgerlaan 171, B-2020 Antwerp (Belgium)

2011-10-15

We aimed at evaluating the effect of low-level air pollution on leaf area fluctuating asymmetry (FAA) and specific leaf area (SLA) of Salix alba L., taking into account other environmental factors. Cuttings were grown in standardized conditions in the near vicinity of air quality measuring stations in Belgium. Variability of SLA and FAA between measuring stations explained 83% and 7.26%, respectively, of the total variability. FAA was not influenced by air pollution or environmental factors such as shading, herbivory, air temperature and humidity. SLA was increased by an increase in shadow, while NO{sub x} and O{sub 3} concentrations had only a marginal influence. The influence of SO{sub 2} concentration was negligible. Although our data analysis suggests a relationship between SLA and NO{sub x}/O{sub 3} concentration, the absence of a straightforward relationship between FAA and SLA and air pollution still questions the usefulness of these bio-indicators for monitoring air pollution. - Highlights: > Leaf characteristics of white willow as possible bio-indicators for air quality. > Fluctuating asymmetry is not a good bio-indicator for monitoring the air quality. > Shadow increases specific leaf area. > NO{sub x} and O{sub 3} change specific leaf area of white willow. - Specific leaf area of S. alba increased with increasing shade and, in less extent, with increasing NO{sub x} and decreasing O{sub 3} concentration, while leaf asymmetry did not respond to air pollution

The effect of air pollution and other environmental stressors on leaf fluctuating asymmetry and specific leaf area of Salix alba L

International Nuclear Information System (INIS)

Wuytack, Tatiana; Wuyts, Karen; Van Dongen, Stefan; Baeten, Lander; Kardel, Fatemeh; Verheyen, Kris; Samson, Roeland

2011-01-01

We aimed at evaluating the effect of low-level air pollution on leaf area fluctuating asymmetry (FAA) and specific leaf area (SLA) of Salix alba L., taking into account other environmental factors. Cuttings were grown in standardized conditions in the near vicinity of air quality measuring stations in Belgium. Variability of SLA and FAA between measuring stations explained 83% and 7.26%, respectively, of the total variability. FAA was not influenced by air pollution or environmental factors such as shading, herbivory, air temperature and humidity. SLA was increased by an increase in shadow, while NO x and O 3 concentrations had only a marginal influence. The influence of SO 2 concentration was negligible. Although our data analysis suggests a relationship between SLA and NO x /O 3 concentration, the absence of a straightforward relationship between FAA and SLA and air pollution still questions the usefulness of these bio-indicators for monitoring air pollution. - Highlights: → Leaf characteristics of white willow as possible bio-indicators for air quality. → Fluctuating asymmetry is not a good bio-indicator for monitoring the air quality. → Shadow increases specific leaf area. → NO x and O 3 change specific leaf area of white willow. - Specific leaf area of S. alba increased with increasing shade and, in less extent, with increasing NO x and decreasing O 3 concentration, while leaf asymmetry did not respond to air pollution

Use of NAP gene to manipulate leaf senescence in plants

Science.gov (United States)

Gan, Susheng; Guo, Yongfeng

2013-04-16

The present invention discloses transgenic plants having an altered level of NAP protein compared to that of a non-transgenic plant, where the transgenic plants display an altered leaf senescence phenotype relative to a non-transgenic plant, as well as mutant plants comprising an inactivated NAP gene, where mutant plants display a delayed leaf senescence phenotype compared to that of a non-mutant plant. The present invention also discloses methods for delaying leaf senescence in a plant, as well as methods of making a mutant plant having a decreased level of NAP protein compared to that of a non-mutant plant, where the mutant plant displays a delayed leaf senescence phenotype relative to a non-mutant plant. Methods for causing precocious leaf senescence or promoting leaf senescence in a plant are also disclosed. Also disclosed are methods of identifying a candidate plant suitable for breeding that displays a delayed leaf senescence and/or enhanced yield phenotype.

A better way of representing stem area index in two-big-leaf models: the application and impact on canopy integration of leaf nitrogen content

Science.gov (United States)

Chen, M.; Butler, E. E.; Wythers, K. R.; Kattge, J.; Ricciuto, D. M.; Thornton, P. E.; Atkin, O. K.; Flores-Moreno, H.; Reich, P. B.

2017-12-01

In order to better estimate the carbon budget of the globe, accurately simulating gross primary productivity (GPP) in earth system models is critical. When upscaling leaf level photosynthesis to the canopy, climate models uses different big-leaf schemes. About half of the state-of-the-art earth system models use a "two-big-leaf" scheme that partitions canopies into direct and diffusively illuminated fractions to reduce high bias of GPP simulated by one-big-leaf models. Some two-big-leaf models, such as ACME (identical in this respect to CLM 4.5) add leaf area index (LAI) and stem area index (SAI) together when calculating canopy radiation transfer. This treatment, however, will result in higher fraction of sunlit leaves. It will also lead to an artificial overestimation of canopy nitrogen content. Here we introduce a new algorithm of simulating SAI in a two-big-leaf model. The new algorithm reduced the sunlit leave fraction of the canopy and conserved the nitrogen content from leaf to canopy level. The lower fraction of sunlit leaves reduced global GPP especially in tropical area. Compared to the default model, for the past 100 years (1909-2009), the averaged global annual GPP is lowered by 4.11 PgC year-1 using this new algorithm.

Timing and duration of autumn leaf development in Sweden

Science.gov (United States)

Bolmgren, Kjell

2014-05-01

The growing season is changing in both ends and autumn phases seem to be responding in more diverse ways than spring events. Indeed, we know little about autumn leaf phenological strategies and how they are correlated with fitness components or ecosystem properties, and how they vary between species and over bioclimatic gradients. In this study more than 10 000 students were involved in observing autumn leaf development at 378 sites all over Sweden (55-68°N). They followed an image based observation protocol classifying autumn leaf development into five levels, from summer green (level 0) to 100% autumn leaf colored (level 4) canopy. In total, they submitted almost 12 000 observations between August 9 and November 15. 75% of the observations were made on the common species of Populus tremula, Betula pendula/pubescens and Sorbus aucuparia. The expected (negative) correlation between latitude and start of leaf senescence (level 2) was found in Populus and Betula, but not in Sorbus. The duration of the leaf senescence period, defined as the period between 1/3 (level 2) and 100% (level 4) of the canopy autumn leaf colored, was negatively correlated with latitude in Populus and Betula, but not in Sorbus. There was also a strong (negative) correlation of the start (level 2) and the duration of the leaf senescence in the early senescing Sorbus and Betula, while this effect was weaker in the late senescing Populus.

Leaf size indices and structure of the peat swamp forest

Directory of Open Access Journals (Sweden)

L.G. Aribal

2017-12-01

Full Text Available Leaf size indices of the tree species in the peatland of Agusan del Sur in Mindanao in Philippines was examined to deduce the variation of forest structure and observed forest zonation.  Using raunkiaer and webb’s leaf size classification, the leaf morphometrics of seven tree species consistently found on the established sampling plots were determined.  The species includes Ternstroemia philippinensis Merr., Polyscias aherniana Merr. Lowry and G.M. Plunkett, Calophyllum sclerophyllum Vesque, Fagraea racemosa Jack, Ilex cymosa Blume, Syzygium tenuirame (Miq. Merr. and Tristaniopsis micrantha Merr. Peter G.Wilson and J.T.Waterh.The LSI were correlated against the variables of the peat physico-chemical properties (such as bulk density, acrotelm thickness, peat depth, total organic carbon, nitrogen, phosphorus, and potassium, pH; water (pH, ammonium, nitrate, phosphate; and leaf tissue elements (nitrogen, phosphorus and potassium.  Result showed a decreasing leaf size indices and a three leaf size category consisting of mesophyllous, mesophyllous-notophyllous and microphyllous were observed which corresponds to the structure of vegetation i.e., from the tall-pole forest having the biggest average leaf area of 6,142.29 mm2 to the pygmy forest with average leaf area of 1,670.10 mm2.  Such decreased leaf size indices were strongly correlated to soil nitrogen, acrotelm thickness, peat depth, phosphate in water, nitrogen and phosphorus in the plant tissue.

Evaluation of two methods of predicting MLC leaf positions using EPID measurements

International Nuclear Information System (INIS)

Parent, Laure; Seco, Joao; Evans, Phil M.; Dance, David R.; Fielding, Andrew

2006-01-01

In intensity modulated radiation treatments (IMRT), the position of the field edges and the modulation within the beam are often achieved with a multileaf collimator (MLC). During the MLC calibration process, due to the finite accuracy of leaf position measurements, a systematic error may be introduced to leaf positions. Thereafter leaf positions of the MLC depend on the systematic error introduced on each leaf during MLC calibration and on the accuracy of the leaf position control system (random errors). This study presents and evaluates two methods to predict the systematic errors on the leaf positions introduced during the MLC calibration. The two presented methods are based on a series of electronic portal imaging device (EPID) measurements. A comparison with film measurements showed that the EPID could be used to measure leaf positions without introducing any bias. The first method, referred to as the 'central leaf method', is based on the method currently used at this center for MLC leaf calibration. It mimics the manner in which leaf calibration parameters are specified in the MLC control system and consequently is also used by other centers. The second method, a new method proposed by the authors and referred to as the ''individual leaf method,'' involves the measurement of two positions for each leaf (-5 and +15 cm) and the interpolation and extrapolation from these two points to any other given position. The central leaf method and the individual leaf method predicted leaf positions at prescribed positions of -11, 0, 5, and 10 cm within 2.3 and 1.0 mm, respectively, with a standard deviation (SD) of 0.3 and 0.2 mm, respectively. The individual leaf method provided a better prediction of the leaf positions than the central leaf method. Reproducibility tests for leaf positions of -5 and +15 cm were performed. The reproducibility was within 0.4 mm on the same day and 0.4 mm six weeks later (1 SD). Measurements at gantry angles of 0 deg., 90 deg., and 270 deg

Climatic Controls on Leaf Nitrogen Content and Implications for Biochemical Modeling.

Science.gov (United States)

Tcherednichenko, I. A.; White, M.; Bastidas, L.

2007-12-01

Leaf nitrogen (N) content, expressed as percent total nitrogen per unit of leaf dry mass, is a widely used parameter in biochemical modeling, due mainly to its role as a potentially limiting factor for photosynthesis. The amount of nitrogen, however, does not occur in a fixed amount in every leaf, but rather varies continuously with the leaf life cycle, in constant response to soil-root-stem-leaf-climate interactions and demand for growth. Moreover, while broad data on leaf N has become available it is normally measured under ambient conditions with consequent difficulty for distinguishing between genetic and time specific environmental effects. In the present work we: 1) Investigate the theoretical variation of leaf mass, specific heat capacity and leaf thickness of full sun-expanded leaves as a regulatory mechanism to ensure thermal survival along with long-term climatic radiation/temperature gradient; and discuss nitrogen and carbon controls on leaf thickness. 2) Based on possible states of partition between nitrogenous and non-nitrogenous components of a leaf we further derive probability density functions (PDFs) of nitrogen and carbon content and assess the effect of water and nutrient uptake on the PDFs. 3) Translate the results to spatially explicit representation over the conterminous USA at 1 km spatial resolution by providing maximum potential values of leaf N of fully expanded leaf optimally suited for long term climatic averages values and soils conditions. Implications for potential presence of inherently slow/fast growing species are discussed along with suitability of results for use by biochemical models.

Trade-offs between seed and leaf size (seed-phytomer-leaf theory): functional glue linking regenerative with life history strategies … and taxonomy with ecology?

Science.gov (United States)

Hodgson, John G; Santini, Bianca A; Montserrat Marti, Gabriel; Royo Pla, Ferran; Jones, Glynis; Bogaard, Amy; Charles, Mike; Font, Xavier; Ater, Mohammed; Taleb, Abdelkader; Poschlod, Peter; Hmimsa, Younes; Palmer, Carol; Wilson, Peter J; Band, Stuart R; Styring, Amy; Diffey, Charlotte; Green, Laura; Nitsch, Erika; Stroud, Elizabeth; Romo-Díez, Angel; de Torres Espuny, Lluis; Warham, Gemma

2017-11-10

While the 'worldwide leaf economics spectrum' (Wright IJ, Reich PB, Westoby M, et al. 2004. The worldwide leaf economics spectrum. Nature : 821-827) defines mineral nutrient relationships in plants, no unifying functional consensus links size attributes. Here, the focus is upon leaf size, a much-studied plant trait that scales positively with habitat quality and components of plant size. The objective is to show that this wide range of relationships is explicable in terms of a seed-phytomer-leaf (SPL) theoretical model defining leaf size in terms of trade-offs involving the size, growth rate and number of the building blocks (phytomers) of which the young shoot is constructed. Functional data for 2400+ species and English and Spanish vegetation surveys were used to explore interrelationships between leaf area, leaf width, canopy height, seed mass and leaf dry matter content (LDMC). Leaf area was a consistent function of canopy height, LDMC and seed mass. Additionally, size traits are partially uncoupled. First, broad laminas help confer competitive exclusion while morphologically large leaves can, through dissection, be functionally small. Secondly, leaf size scales positively with plant size but many of the largest-leaved species are of medium height with basally supported leaves. Thirdly, photosynthetic stems may represent a functionally viable alternative to 'small seeds + large leaves' in disturbed, fertile habitats and 'large seeds + small leaves' in infertile ones. Although key elements defining the juvenile growth phase remain unmeasured, our results broadly support SPL theory in that phytometer and leaf size are a product of the size of the initial shoot meristem (≅ seed mass) and the duration and quality of juvenile growth. These allometrically constrained traits combine to confer ecological specialization on individual species. Equally, they appear conservatively expressed within major taxa. Thus, 'evolutionary canalization' sensu Stebbins (Stebbins GL

Antioxidant Activity and Cytotoxicity of the Leaf and Bark Extracts of ...

African Journals Online (AJOL)

Purpose: To investigate the antioxidant potential and cytotoxicity of the leaf and bark extracts of Tarchonanathus campharatus.. Methods: The antioxidant activity of the aqueous leaf extract (Aq LF), methanol leaf extract (MET LF), dichloromethane leaf extract (DCM LF), methanol bark extract (MET BK), dichloromethane bark ...

Estimating leaf photosynthetic pigments information by stepwise multiple linear regression analysis and a leaf optical model

Science.gov (United States)

Liu, Pudong; Shi, Runhe; Wang, Hong; Bai, Kaixu; Gao, Wei

2014-10-01

Leaf pigments are key elements for plant photosynthesis and growth. Traditional manual sampling of these pigments is labor-intensive and costly, which also has the difficulty in capturing their temporal and spatial characteristics. The aim of this work is to estimate photosynthetic pigments at large scale by remote sensing. For this purpose, inverse model were proposed with the aid of stepwise multiple linear regression (SMLR) analysis. Furthermore, a leaf radiative transfer model (i.e. PROSPECT model) was employed to simulate the leaf reflectance where wavelength varies from 400 to 780 nm at 1 nm interval, and then these values were treated as the data from remote sensing observations. Meanwhile, simulated chlorophyll concentration (Cab), carotenoid concentration (Car) and their ratio (Cab/Car) were taken as target to build the regression model respectively. In this study, a total of 4000 samples were simulated via PROSPECT with different Cab, Car and leaf mesophyll structures as 70% of these samples were applied for training while the last 30% for model validation. Reflectance (r) and its mathematic transformations (1/r and log (1/r)) were all employed to build regression model respectively. Results showed fair agreements between pigments and simulated reflectance with all adjusted coefficients of determination (R2) larger than 0.8 as 6 wavebands were selected to build the SMLR model. The largest value of R2 for Cab, Car and Cab/Car are 0.8845, 0.876 and 0.8765, respectively. Meanwhile, mathematic transformations of reflectance showed little influence on regression accuracy. We concluded that it was feasible to estimate the chlorophyll and carotenoids and their ratio based on statistical model with leaf reflectance data.

Optimal leaf positions for chlorophyll meter measurement in rice

Directory of Open Access Journals (Sweden)

Zhaofeng eYuan

2016-05-01

Full Text Available The Soil Plant Analysis Development (SPAD chlorophyll meter is one of the most commonly used diagnostic tools to measure crop nitrogen status. However, the measurement method of the meter could significantly affect the accuracy of the final estimation. Thus, this research was undertaken to develop a new methodology to optimize SPAD meter measurements in rice (Oryza sativa L.. A flatbed color scanner was used to map the dynamic chlorophyll distribution and irregular leaf shapes. Calculus algorithm was adopted to estimate the potential positions for SPAD meter measurement along the leaf blade. Data generated by the flatbed color scanner and SPAD meter were analysed simultaneously. The results suggested that a position 2/3 of the distance from the leaf base to the apex (2/3 position could represent the chlorophyll content of the entire leaf blade, as indicated by the relatively low variance of measurements at that positon. SPAD values based on di-positional leaves and the extracted chlorophyll a and b contents were compared. This comparison showed that the 2/3 position on the lower leaves tended to be more sensitive to changes in chlorophyll content. Finally, the 2/3 position and average SPAD values of the fourth fully expanded leaf from the top were compared with leaf nitrogen concentration. The results showed the 2/3 position on that leaf was most suitable for predicting the nitrogen status of rice. Based on these results, we recommend making SPAD measurements at the 2/3 position on the fourth fully expanded leaf from the top. The coupling of dynamic chlorophyll distribution and irregular leaf shapes information can provide a promising approach for the calibration of SPAD meter measurement, which can further benefit the in situ nitrogen management by providing reliable estimation of crops nitrogen nutrition status.

Leaf area prediction models for Tsuga canadensis in Maine

Science.gov (United States)

Laura S. Kenefic; R.S. Seymour

1999-01-01

Tsuga canadensis (L.) Carr. (eastern hemlock) is a common species throughout the Acadian forest. Studies of leaf area and growth efficiency in this forest type have been limited by the lack of equations to predict leaf area of this species. We found that sapwood area was an effective leaf area surrogate in T. canadensis, though...

Simulated Acid Rain-induced Alterations in Flowering, Leaf ...

African Journals Online (AJOL)

Evaluation of SAR effects on budding, flowering, leaf abscission and pollen development revealed that ... Keywords: Simulated acid rain, Helianthus annuus, flowering, leaf abscission, pollen germination, sunflower. ... HOW TO USE AJOL.

Estudo Etnobotânico de plantas medicinais utilizadas pela Comunidade do Sisal no município de Catu, Bahia, Brasil

Directory of Open Access Journals (Sweden)

F.R.G Neto

2014-12-01

Full Text Available A utilização de plantas medicinais é instintiva nos animais, visto que alguns destes buscam raízes, cascas, folhas ou frutos na tentativa de resolver seus males. O homem, por sua vez, aprendeu a utilizar estas informações empiricamente para fazer uso destes vegetais. A medicina popular é uma importante alternativa, provavelmente, a mais usada para a cura de doenças por parte de populações indígenas, quilombolas ou rurais. A Etnobotânica, por sua vez, encarrega-se de estudar e interpretar essa relação dos homens com o mundo vegetal. Devido ao seu grande potencial biológico e cultural, o Brasil apresenta uma infinidade de conhecimentos tradicionais e espécies vegetais importantes, o que torna esse país uma grande fonte de pesquisa na área. Visando avaliar o conhecimento tradicional da população rural do Sisal, Catu/Bahia, relacionado ao uso de plantas medicinais, este trabalho iniciou-se em julho de 2009, constando de entrevistas semi-estruturadas e estruturadas, gravações, registros fotográficos, coleta do material botânico indicado nas entrevistas com os informantes, tratamento do material coletado e incorporação ao Herbário da Universidade do Estado da Bahia (HUNEB. Foram identificadas e coletadas 54 espécies distribuídas em 46 gêneros e 28 famílias, sendo Lamiacaeae e Asteraceae as mais representativas. A maioria das plantas é constituída de ervas e cultivada nos quintais dos moradores. O estudo revelou que a comunidade apresenta uma medicina popular bastante rica, com grande diversidade de espécies vegetais e usos por parte da população.

A leaf gas exchange model that accounts for intra-canopy variability by considering leaf nitrogen content and local acclimation to radiation in grapevine (Vitis vinifera L.).

Science.gov (United States)

Prieto, Jorge A; Louarn, Gaëtan; Perez Peña, Jorge; Ojeda, Hernán; Simonneau, Thierry; Lebon, Eric

2012-07-01

Understanding the distribution of gas exchange within a plant is a prerequisite for scaling up from leaves to canopies. We evaluated whether leaf traits were reliable predictors of the effects of leaf ageing and leaf irradiance on leaf photosynthetic capacity (V(cmax) , J(max) ) in field-grown vines (Vitis vinifera L). Simultaneously, we measured gas exchange, leaf mass per area (LMA) and nitrogen content (N(m) ) of leaves at different positions within the canopy and at different phenological stages. Daily mean leaf irradiance cumulated over 10 d (PPFD(10) ) was obtained by 3D modelling of the canopy structure. N(m) decreased over the season in parallel to leaf ageing while LMA was mainly affected by leaf position. PPFD(10) explained 66, 28 and 73% of the variation of LMA, N(m) and nitrogen content per area (N(a) ), respectively. Nitrogen content per unit area (N(a) = LMA × N(m) ) was the best predictor of the intra-canopy variability of leaf photosynthetic capacity. Finally, we developed a classical photosynthesis-stomatal conductance submodel and by introducing N(a) as an input, the model accurately simulated the daily pattern of gas exchange for leaves at different positions in the canopy and at different phenological stages during the season. © 2012 Blackwell Publishing Ltd.

The role of the medial prefrontal cortex in the play fighting of rats.

Science.gov (United States)

Bell, Heather C; McCaffrey, David R; Forgie, Margaret L; Kolb, Bryan; Pellis, Sergio M

2009-12-01

Although decorticated rats are able to engage in play, their play is abnormal in three ways. First, decorticates do not display the normal, age-related shifts in defensive strategies during development. Second, decorticates do not modify their defensive tactics in response to the social identity of their partners. Third, decorticates display a global shift in defensive tactics from more complex to less complex strategies. It has been shown that lesions of the motor cortex (MC) selectively produce the abnormal developmental effects on play, and that lesions of the orbitofrontal cortex (OFC) selectively produce the deficits in behavioral discrimination between social partners. In the current set of experiments, we demonstrate that lesions of the medial prefrontal cortex (mPFC) produce the shift from more complex to less complex defensive tactics, while leaving intact the age-related and partner-related modulation of defensive strategies. Thus, we have evidence for a triple dissociation of function between the MC, the OFC, and the mPFC with respect to social play behavior.

Optimal leaf sequencing with elimination of tongue-and-groove underdosage

Energy Technology Data Exchange (ETDEWEB)

Kamath, Srijit [Department of Computer and Information Science and Engineering, University of Florida, Gainesville, FL (United States); Sahni, Sartaj [Department of Computer and Information Science and Engineering, University of Florida, Gainesville, FL (United States); Palta, Jatinder [Department of Radiation Oncology, University of Florida, Gainesville, FL (United States); Ranka, Sanjay [Department of Computer and Information Science and Engineering, University of Florida, Gainesville, FL (United States); Li, Jonathan [Department of Radiation Oncology, University of Florida, Gainesville, FL (United States)

2004-02-07

The individual leaves of a multileaf collimator (MLC) have a tongue-and-groove or stepped-edge design to minimize leakage radiation between adjacent leaves. This design element has a drawback in that it creates areas of underdosages in intensity-modulated photon beams unless a leaf trajectory is specifically designed such that for any two adjacent leaf pairs, the direct exposure under the tongue-and-groove is equal to the lower of the direct exposures of the leaf pairs. In this work, we present a systematic study of the optimization of a leaf sequencing algorithm for segmental multileaf collimator beam delivery that completely eliminates areas of underdosages due to tongue-and-groove or stepped-edge design of the MLC. Simultaneous elimination of tongue-and-groove effect and leaf interdigitation is also studied. This is an extension of our previous work (Kamath et al 2003a Phys. Med. Biol. 48 307) in which we described a leaf sequencing algorithm that is optimal for monitor unit (MU) efficiency under most common leaf movement constraints that include minimum leaf separation. Compared to our previously published algorithm (without constraints), the new algorithms increase the number of sub-fields by approximately 21% and 25%, respectively, but are optimal in MU efficiency for unidirectional schedules. (note)

Optimal leaf sequencing with elimination of tongue-and-groove underdosage

International Nuclear Information System (INIS)

Kamath, Srijit; Sahni, Sartaj; Palta, Jatinder; Ranka, Sanjay; Li, Jonathan

2004-01-01

The individual leaves of a multileaf collimator (MLC) have a tongue-and-groove or stepped-edge design to minimize leakage radiation between adjacent leaves. This design element has a drawback in that it creates areas of underdosages in intensity-modulated photon beams unless a leaf trajectory is specifically designed such that for any two adjacent leaf pairs, the direct exposure under the tongue-and-groove is equal to the lower of the direct exposures of the leaf pairs. In this work, we present a systematic study of the optimization of a leaf sequencing algorithm for segmental multileaf collimator beam delivery that completely eliminates areas of underdosages due to tongue-and-groove or stepped-edge design of the MLC. Simultaneous elimination of tongue-and-groove effect and leaf interdigitation is also studied. This is an extension of our previous work (Kamath et al 2003a Phys. Med. Biol. 48 307) in which we described a leaf sequencing algorithm that is optimal for monitor unit (MU) efficiency under most common leaf movement constraints that include minimum leaf separation. Compared to our previously published algorithm (without constraints), the new algorithms increase the number of sub-fields by approximately 21% and 25%, respectively, but are optimal in MU efficiency for unidirectional schedules. (note)

Do Aphids Alter Leaf Surface Temperature Patterns During Early Infestation?

Directory of Open Access Journals (Sweden)

Thomas Cahon

2018-03-01

Full Text Available Arthropods at the surface of plants live in particular microclimatic conditions that can differ from atmospheric conditions. The temperature of plant leaves can deviate from air temperature, and leaf temperature influences the eco-physiology of small insects. The activity of insects feeding on leaf tissues, may, however, induce changes in leaf surface temperatures, but this effect was only rarely demonstrated. Using thermography analysis of leaf surfaces under controlled environmental conditions, we quantified the impact of presence of apple green aphids on the temperature distribution of apple leaves during early infestation. Aphids induced a slight change in leaf surface temperature patterns after only three days of infestation, mostly due to the effect of aphids on the maximal temperature that can be found at the leaf surface. Aphids may induce stomatal closure, leading to a lower transpiration rate. This effect was local since aphids modified the configuration of the temperature distribution over leaf surfaces. Aphids were positioned at temperatures near the maximal leaf surface temperatures, thus potentially experiencing the thermal changes. The feedback effect of feeding activity by insects on their host plant can be important and should be quantified to better predict the response of phytophagous insects to environmental changes.

Leaf micromorphology of some Phyllanthus L. species (Phyllanthaceae)

Energy Technology Data Exchange (ETDEWEB)

Solihani, N. S., E-mail: noorsolihani@gmail.com; Noraini, T., E-mail: norainitalip@gmail.com [School of Environmental and Natural Resource Sciences Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Azahana, A., E-mail: bell-azahana@yahoo.com [Department of Plant Science, Kulliyyah of Science, International Islamic University Malaysia, Kuantan Campus, Kuantan, Pahang (Malaysia); Nordahlia, A. S., E-mail: nordahlia@frim.gov.my [Forest Research Institute of Malaysia, 52109 Kepong, Selangor (Malaysia)

2015-09-25

Comparative leaf micromorphological study was conducted of five chosen Phyllanthus L. (Phyllanthaceae) species, namely P. acidus L., P. elegans Wall. ex Müll. Arg., P. emblica L., P. urinaria L. and P. pulcher Wall. ex Müll. Arg. The objective of this study is to identify the leaf micromorphological characteristics that can be used in species identification. The procedures involve examination under scanning electron microscope. Findings of this study have demonstrated variations in the leaf micromorphological characteristics such as in the types of waxes present on adaxial and abaxial epidermis surfaces, in the stomata and types of trichome. Common character present in all species studied are the presence of a thin film layer and buttress-like waxes on epidermal leaf surfaces. Diagnostics characters found in this study are the presence of papilla in P. elegens, amphistomatic stomata in P. urinaria and flaky waxes in P. pulcher. The result of this study has shown that leaf micromorphological characters have some taxonomic significance and can be used in identification of species in the genus Phyllanthus.

Leaf absorbance and photosynthesis

Science.gov (United States)

Schurer, Kees

1994-01-01

The absorption spectrum of a leaf is often thought to contain some clues to the photosynthetic action spectrum of chlorophyll. Of course, absorption of photons is needed for photosynthesis, but the reverse, photosynthesis when there is absorption, is not necessarily true. As a check on the existence of absorption limits we measured spectra for a few different leaves. Two techniques for measuring absorption have been used, viz. the separate determination of the diffuse reflectance and the diffuse transmittance with the leaf at a port of an integrating sphere and the direct determination of the non-absorbed fraction with the leaf in the sphere. In a cross-check both methods yielded the same results for the absorption spectrum. The spectrum of a Fuchsia leaf, covering the short-wave region from 350 to 2500 nm, shows a high absorption in UV, blue and red, the well known dip in the green and a steep fall-off at 700 nm. Absorption drops to virtually zero in the near infrared, with subsequent absorptions, corresponding to the water absorption bands. In more detailed spectra, taken at 5 nm intervals with a 5 nm bandwidth, differences in chlorophyll content show in the different depths of the dip around 550 nm and in a small shift of the absorption edge at 700 nm. Spectra for Geranium (Pelargonium zonale) and Hibiscus (with a higher chlorophyll content) show that the upper limit for photosynthesis can not be much above 700 nm. No evidence, however, is to be seen of a lower limit for photosynthesis and, in fact, some experiments down to 300 nm still did not show a decrease of the absorption although it is well recognized that no photosynthesis results with 300 nm wavelengths.

Antibacterial Activity of Vernonia amygdalina Leaf Extracts against ...

African Journals Online (AJOL)

ADOWIE PERE

(Bitter leaf), Allium sativum (Garlic), O. gratissimum. (Scent leaf) ... complex active components that are useful ... hydroxide was added. .... KEY: CPX-Ciprofloxacin, Ro-Rocephin, St-Streptomycin, AU-Augmentin, SXT-Septrin, SP- Sparfloxacin, ...

Estimation of leaf area in tropical maize

NARCIS (Netherlands)

Elings, A.

2000-01-01

Leaf area development of six tropical maize cultivars grown in 1995 and 1996 in several tropical environments in Mexico (both favourable and moisture-and N-limited) was observed and analysed. First, the validity of a bell-shaped curve describing the area of individual leaves as a function of leaf

Frost and leaf-size gradients in forests: global patterns and experimental evidence.

Science.gov (United States)

Lusk, Christopher H; Clearwater, Michael J; Laughlin, Daniel C; Harrison, Sandy P; Prentice, Iain Colin; Nordenstahl, Marisa; Smith, Benjamin

2018-05-16

Explanations of leaf size variation commonly focus on water availability, yet leaf size also varies with latitude and elevation in environments where water is not strongly limiting. We provide the first conclusive test of a prediction of leaf energy balance theory that may explain this pattern: large leaves are more vulnerable to night-time chilling, because their thick boundary layers impede convective exchange with the surrounding air. Seedlings of 15 New Zealand evergreens spanning 12-fold variation in leaf width were exposed to clear night skies, and leaf temperatures were measured with thermocouples. We then used a global dataset to assess several climate variables as predictors of leaf size in forest assemblages. Leaf minus air temperature was strongly correlated with leaf width, ranging from -0.9 to -3.2°C in the smallest- and largest-leaved species, respectively. Mean annual temperature and frost-free period were good predictors of evergreen angiosperm leaf size in forest assemblages, but no climate variable predicted deciduous leaf size. Although winter deciduousness makes large leaves possible in strongly seasonal climates, large-leaved evergreens are largely confined to frost-free climates because of their susceptibility to radiative cooling. Evergreen leaf size data can therefore be used to enhance vegetation models, and to infer palaeotemperatures from fossil leaf assemblages. © 2018 The Authors New Phytologist © 2018 New Phytologist Trust.

TALE and Shape: How to Make a Leaf Different.

Science.gov (United States)

Di Giacomo, Elisabetta; Iannelli, Maria Adelaide; Frugis, Giovanna

2013-05-06

The Three Amino acid Loop Extension (TALE) proteins constitute an ancestral superclass of homeodomain transcription factors conserved in animals, plants and fungi. In plants they comprise two classes, KNOTTED1-LIKE homeobox (KNOX) and BEL1-like homeobox (BLH or BELL, hereafter referred to as BLH), which are involved in shoot apical meristem (SAM) function, as well as in the determination and morphological development of leaves, stems and inflorescences. Selective protein-protein interactions between KNOXs and BLHs affect heterodimer subcellular localization and target affinity. KNOXs exert their roles by maintaining a proper balance between undifferentiated and differentiated cell state through the modulation of multiple hormonal pathways. A pivotal function of KNOX in evolutionary diversification of leaf morphology has been assessed. In the SAM of both simple- and compound-leafed seed species, downregulation of most class 1 KNOX (KNOX1) genes marks the sites of leaf primordia initiation. However, KNOX1 expression is re-established during leaf primordia development of compound-leafed species to maintain transient indeterminacy and morphogenetic activity at the leaf margins. Despite the increasing knowledge available about KNOX1 protein function in plant development, a comprehensive view on their downstream effectors remains elusive. This review highlights the role of TALE proteins in leaf initiation and morphological plasticity with a focus on recent advances in the identification of downstream target genes and pathways.

Simple models for predicting leaf area of mango (Mangifera indica L.

Directory of Open Access Journals (Sweden)

Maryam Ghoreishi

2012-01-01

Full Text Available Mango (Mangifera indica L., one of the most popular tropical fruits, is cultivated in a considerable part of southern Iran. Leaf area is a valuable parameter in mango research, especially plant physiological and nutrition field. Most of available methods for estimating plant leaf area are difficult to apply, expensive and destructive which could in turn destroy the canopy and consequently make it difficult to perform further tests on the same plant. Therefore, a non-destructive method which is simple, inexpensive, and could yield an accurate estimation of leaf area will be a great benefit to researchers. A regression analysis was performed in order to determine the relationship between the leaf area and leaf width, leaf length, dry and fresh weight. For this purpose 50 mango seedlings of local selections were randomly took from a nursery in the Hormozgan province, and different parts of plants were separated in laboratory. Leaf area was measured by different method included leaf area meter, planimeter, ruler (length and width and the fresh and dry weight of leaves were also measured. The best regression models were statistically selected using Determination Coefficient, Maximum Error, Model Efficiency, Root Mean Square Error and Coefficient of Residual Mass. Overall, based on regression equation, a satisfactory estimation of leaf area was obtained by measuring the non-destructive parameters, i.e. number of leaf per seedling, length of the longest and width of widest leaf (R2 = 0.88 and also destructive parameters, i.e. dry weight (R2 = 0.94 and fresh weight (R2= 0.94 of leaves.

Effects of leaf age within growth stages of pepper and sorghum plants on leaf thickness, water, chlorophyll, and light reflectance. [in spectral vegetation discrimination

Science.gov (United States)

Gausman, H. W.; Cardenas, R.; Berumen, A.

1974-01-01

Pepper and sorghum plants (characterized by porous and compact leaf mesophylls, respectively) were used to study the influence of leaf age on light reflectance. Measurements were limited to the upper five nodal positions within each growth stage, since upper leaves make up most of the reflectance surfaces remotely sensed. The increase in leaf thickness and water content with increasing leaf age was taken into consideration, since each of these factors affects the reflectance as well as the selection of spectral wavelength intervals for optimum discrimination of vegetation.

Ontogeny of the sheathing leaf base in maize (Zea mays).

Science.gov (United States)

Johnston, Robyn; Leiboff, Samuel; Scanlon, Michael J

2015-01-01

Leaves develop from the shoot apical meristem (SAM) via recruitment of leaf founder cells. Unlike eudicots, most monocot leaves display parallel venation and sheathing bases wherein the margins overlap the stem. Here we utilized computed tomography (CT) imaging, localization of PIN-FORMED1 (PIN1) auxin transport proteins, and in situ hybridization of leaf developmental transcripts to analyze the ontogeny of monocot leaf morphology in maize (Zea mays). CT imaging of whole-mounted shoot apices illustrates the plastochron-specific stages during initiation of the basal sheath margins from the tubular disc of insertion (DOI). PIN1 localizations identify basipetal auxin transport in the SAM L1 layer at the site of leaf initiation, a process that continues reiteratively during later recruitment of lateral leaf domains. Refinement of these auxin transport domains results in multiple, parallel provascular strands within the initiating primordium. By contrast, auxin is transported from the L2 toward the L1 at the developing margins of the leaf sheath. Transcripts involved in organ boundary formation and dorsiventral patterning accumulate within the DOI, preceding the outgrowth of the overlapping margins of the sheathing leaf base. We suggest a model wherein sheathing bases and parallel veins are both patterned via the extended recruitment of lateral maize leaf domains from the SAM. © 2014 The Authors. New Phytologist © 2014 New Phytologist Trust.

CIRCADIAN CLOCK-ASSOCIATED 1 Inhibits Leaf Senescence in Arabidopsis

Directory of Open Access Journals (Sweden)

Yi Song

2018-03-01

Full Text Available Leaf senescence is an integral part of plant development, and the timing and progressing rate of senescence could substantially affect the yield and quality of crops. It has been known that a circadian rhythm synchronized with external environmental cues is critical for the optimal coordination of various physiological and metabolic processes. However, the reciprocal interactions between the circadian clock and leaf senescence in plants remain unknown. Here, through measuring the physiological and molecular senescence related markers of several circadian components mutants, we found that CIRCADIAN CLOCK-ASSOCIATED 1 inhibits leaf senescence. Further molecular and genetic studies revealed that CCA1 directly activates GLK2 and suppresses ORE1 expression to counteract leaf senescence. As plants age, the expression and periodic amplitude of CCA1 declines and thus weakens the inhibition of senescence. Our findings reveal an age-dependent circadian clock component of the process of leaf senescence.

Accumulation of three different sizes of particulate matter on plant leaf surfaces: Effect on leaf traits

Directory of Open Access Journals (Sweden)

Chen Xiaoping

2015-01-01

Full Text Available Plants not only improve air quality by adsorbing particulate matter (PM on leaf surfaces but can also be affected by their accumulation. In this study, a field investigation was performed in Wuhan, China, into the relationship between seven leaf traits and the accumulation of three different sizes of PM (PM11, PM2.5 and PM0.2 on leaves. The retention abilities of plant leaves with respect to the three sizes of PM differed significantly at different sites and species. The average PM retention capabilities of plant leaves and specific leaf area (SLA were significantly greater in a seriously polluted area, whereas the average values of chlorophyll a (Chl a, chlorophyll b (Chl b, total chlorophyll, carotenoid, pH and relative water content (RWC were greater at the control site. SLA significantly positively correlated with the size of PM, but Chl a, Chl b, total chlorophyll, RWC significantly negatively correlated with the size of PM, whereas the pH did not correlate significantly with the the PM fractions. Additionally, SLA was found to be affected by large particles (PM11, p<0.01; PM2.5 had a more obvious effect on plant leaf traits than the other PM (p<0.05. Overall, the findings from this study provide useful information regarding the selection of plants to reduce atmospheric pollution.

Leaf surface anatomy in some woody plants from northeastern Mexico

International Nuclear Information System (INIS)

Maiti, R.; Rodriguez, H.G.; Balboa, P.C.R.; Kumari, A

2016-01-01

Studies on leaf surface anatomy of woody plants and its significance are rare. The present study was undertaken in the Forest Science Faculty Experimental Research Station, UANL, Mexico, with objectives to determine the variability in leaf surface anatomy in the woody plants of the Tamaulipan thornscrub and its utility in taxonomy and possible adaptation to the prevailing semiarid conditions. The results show the presence of large variability in several leaf anatomical traits viz., waxy leaf surface, type of stomata, its size, and distribution. The species have been classified on the basis of various traits which can be used in species delimitation and adaptation to the semiarid condition such as waxy leaf surface, absence sparse stomata on the leaf surface, sunken stomata. The species identified as better adapters to semi-arid environments on the basis of the presence and absence of stomata on both adaxial and abaxial surface viz., Eysenhardtia texana, Parkinsonia texana, Gymnosperma glutinosum, Celtis laevigata, Condalia hookeri and Karwinskia humboldtiana. (author)

Antibacterial activity, chemical composition, and cytotoxicity of leaf?s essential oil from brazilian pepper tree (schinus terebinthifolius, raddi)

OpenAIRE

Silva, A.B.; Silva, T.; Franco, E.S.; Rabelo, S.A.; Lima, E.R.; Mota, R.A.; da C?mara, C.A.G.; Pontes-Filho, N.T.; Lima-Filho, J.V.

2010-01-01

The antibacterial potential of leaf?s essential oil (EO) from Brazilian pepper tree (Schinus terebinthifolius Raddi) against staphylococcal isolates from dogs with otitis externa was evaluated. The minimum inhibitory concentration of EO ranged from 78.1 to 1,250 ?g/mL. The oil was analyzed by GC and GC/MS and cytotoxicity tests were carried out with laboratory animals.

Effects of canopy structural variables on retrieval of leaf dry matter content and specific leaf area from remotely sensed data

NARCIS (Netherlands)

Ali, A.M.; Darvishzadeh, R.; Skidmore, A.K.; van Duren, I.C.

2016-01-01

Leaf dry matter content (LDMC) and specific leaf area (SLA) are two important traits in measuring biodiversity. To use remote sensing for the estimation of these traits, it is essential to understand the underlying factors that influence their relationships with canopy reflectance. The effect of

[Effects of simulated warming on the growth, leaf phenology, and leaf traits of Salix eriostachya in sub-alpine timberline ecotone of western Sichuan, China].

Science.gov (United States)

Xu, Zhen-feng; Hu, Ting-xing; Zhang, Li; Zhang, Yuan-bin; Xian, Jun-ren; Wang, Kai-yun

2009-01-01

By using open-top chamber (OTC), the effects of simulated warming on the growth, leaf phenology, and leaf traits of Salix eriostachya in sub-alpine timberline ecotone of Western Sichuan were studied. The results showed that comparing with the control, the mean air temperature at 1.2 m above the ground throughout S. eriostachya growth season in OTC increased by 2.9 degrees C, while the soil temperature at the depth of 5 cm only increased by 0.4 degrees C. The temperature increase in OTC made S. eriostachya budding advanced and defoliation postponed obviously, and the leaf life-span longer. The leaf and branch growth rates as well as the specific leaf area in OTC increased obviously, whereas the leaf nitrogen concentration decreased significantly. In OTC, the stomata conductance, net photosynthetic rate, photorespiration, and dark respiration rate of S. eriostachya all exhibited an increasing trend. It was suggested that S. eriostachya had stronger capability to adapt to warming, and, under the background of future global climate change, the elevation of S. eriostachya distribution in the timberline ecotone would be likely to ascend.

Penumbra measurements of BeamModulatorTM multi leaf collimator

International Nuclear Information System (INIS)

Lu Xiaoguang; Wang Yunlai; Huo Xiaoqing; Sha Xiangyan; Miao Xiongfei

2010-01-01

Objective: To evaluate the penumbra of a new multileaf collimator equipped with Elekta Synergy accelerator. Methods: The penumbra were derived from beam profiles measured in air and water using PinPoint ion chamber with PTW MP3 water phantom. Variations of penumbra with X-ray beam energy, depth in water, and leaf position were investigated. Results: The penumbra in air for 6 MV X-ray was 2 mm less than that at depth of maximal dose in water. The penumbra of leaf side was 1 mm less than that of the leaf end. The penumbra had close relationship with beam energy, depth in water and leaf position. penumbra increased with beam quality and water depth. The leaf position had great influence on the penumbra. Conclusions: The penumbra of the multileaf collimator is related to its original design and radiation delivery technique. Special considerations should be taken into during treatment planning. Regular measurement should be performed to guarantee the delivery quality. (authors)

Inverse gradients in leaf wax δD and δ13C values along grass blades of Miscanthus sinensis: implications for leaf wax reproduction and plant physiology.

Science.gov (United States)

Gao, Li; Huang, Yongsong

2013-06-01

Compound specific hydrogen and carbon isotopic ratios of higher plant leaf waxes have been extensively used in paleoclimate and paleoenvironmental reconstructions. However, studies so far have focused on the comparison of leaf wax isotopic differences in bulk leaf samples between different plant species. We sampled three different varieties of tall grasses (Miscanthus sinensis) in six segments from base to tip and determined hydrogen and carbon isotopic ratios of leaf waxes, as well as hydrogen and oxygen isotopic ratios of leaf water samples. We found an increasing, base-to-tip hydrogen isotopic gradient along the grass blades that can probably be attributed to active leaf wax regeneration over the growth season. Carbon isotopic ratios, on the other hand, show opposite trends to hydrogen isotopic ratios along the grass blades, which may reflect different photosynthetic efficiencies at different blade locales.

LEAF MICROMORPHOMETRY OF Schinus molle L. (ANARCADIACEAE IN DIFFERENT CANOPY HEIGHTS.

Directory of Open Access Journals (Sweden)

Marinês Ferreira Pires

2015-03-01

Full Text Available Leaf characterization of trees is essential for its identification and use, as well as to understand its relationships with environment. The objective of this work is to study the leaflet anatomy and leaf biometrical characteristics at different canopy heights of Schinus molle plants as a function of its environmental and physiological modifications. Leaves were collected at three different canopy heights: base, middle and upper canopy in a plantation of S. molle. Leaves were used for anatomical and biometrical analysis. For the anatomical analysis, leaves were fixed in FAA and stored in ethanol 70% and further submitted to transversal and paradermical sections. Slides were photomicrographed and image analysis was performed in UTHSCSA-Imagetool. For biometrical analysis leaf area, length, width, dry mass and specific leaf area were evaluated. The leaflets exhibited single layer epidermis, anomocytic and ciclocytic stomata, isobilateral mesophyll, subepidermal parenchyma layer in both adaxial and abaxial faces of epidermis, secretory vessels and lamellar collenchyma in midrib and leaf border. Leaf anatomy modifications occurred in cuticle and mesophyll thickness, vascular system, phloem thickness, and stomatal density in accordance with leaf canopy position. Leaves were smaller and with reduced leaf area at higher canopy positions. S. molle leaf anatomy is different from other species within Schinus genre with modifications under different environmental and physiological modifications promoted by its canopy height.

The effect of glyphosate on import into a sink leaf of sugar beet

International Nuclear Information System (INIS)

Shieh, Wenjang; Geiger, D.R.

1990-01-01

The basis for glyphosate inducted limitation of carbon import into developing leaves was studied in sugar beet. To separate the effects of the herbicide on export from those on import, glyphosate was supplied to a developing leaf from two exporting source leaves which fed the sink leaf. Carbon import into the sink leaf was determined by supplying 14 CO 2 to a third source leaf which also supplies carbon to the monitored sink leaf. Import into the sink leaf decreased within 2 to 3 h after glyphosate application, even though photosynthesis and export in the source leaf supplying 14 C were unaffected. Reduced import into the sink leaf was accompanied by increased import by the tap root. Elongation of the sink leaf was only slightly decreased following arrival of glyphosate. Photosynthesis by the sink leaf was not inhibited. The results to data support the view that import is slowed by the inhibition of synthesis of structural or storage compounds in the developing leaves

CO2 and temperature effects on leaf area production in two annual plant species

International Nuclear Information System (INIS)

Ackerly, D.D.; Coleman, J.S.; Morse, S.R.; Bazzaz, F.A.

1992-01-01

The authors studied leaf area production in two annual plant species, Abutilon theophrasti and Amaranthus retroflexus, under three day/night temperature regimes and two concentrations of carbon dioxide. The production of whole-plant leaf area during the first 30 d of growth was analyzed in terms of the leaf initiation rate, leaf expansion, individual leaf area, and, in Amaranthus, production of branch leaves. Temperature and CO 2 influenced leaf area production through effects on the rate of development, determined by the production of nodes on the main stem, and through shifts in the relationship between whole-plant leaf area and the number of main stem nodes. In Abutilon, leaf initiation rate was highest at 38 degree, but area of individual leaves was greatest at 28 degree. Total leaf area was greatly reduced at 18 degree due to slow leaf initiation rates. Elevated CO 2 concentration increased leaf initiation rate at 28 degree, resulting in an increase in whole-part leaf area. In Amaranthus, leaf initiation rate increased with temperature, and was increased by elevated CO 2 at 28 degree. Individual leaf area was greatest at 28 degree, and was increased by elevated CO 2 at 28 degree but decreased at 38 degree. Branch leaf area displayed a similar response to CO 2 , butt was greater at 38 degree. Overall, wholeplant leaf area was slightly increased at 38 degree relative to 28 degree, and elevated CO 2 levels resulted in increased leaf area at 28 degree but decreased leaf area at 38 degree

Analysis of leaf surfaces using scanning ion conductance microscopy.

Science.gov (United States)

Walker, Shaun C; Allen, Stephanie; Bell, Gordon; Roberts, Clive J

2015-05-01

Leaf surfaces are highly complex functional systems with well defined chemistry and structure dictating the barrier and transport properties of the leaf cuticle. It is a significant imaging challenge to analyse the very thin and often complex wax-like leaf cuticle morphology in their natural state. Scanning electron microscopy (SEM) and to a lesser extent Atomic force microscopy are techniques that have been used to study the leaf surface but their remains information that is difficult to obtain via these approaches. SEM is able to produce highly detailed and high-resolution images needed to study leaf structures at the submicron level. It typically operates in a vacuum or low pressure environment and as a consequence is generally unable to deal with the in situ analysis of dynamic surface events at submicron scales. Atomic force microscopy also possess the high-resolution imaging required and can follow dynamic events in ambient and liquid environments, but can over exaggerate small features and cannot image most leaf surfaces due to their inherent roughness at the micron scale. Scanning ion conductance microscopy (SICM), which operates in a liquid environment, provides a potential complementary analytical approach able to address these issues and which is yet to be explored for studying leaf surfaces. Here we illustrate the potential of SICM on various leaf surfaces and compare the data to SEM and atomic force microscopy images on the same samples. In achieving successful imaging we also show that SICM can be used to study the wetting of hydrophobic surfaces in situ. This has potentially wider implications than the study of leaves alone as surface wetting phenomena are important in a range of fundamental and applied studies. © 2015 The Authors Journal of Microscopy © 2015 Royal Microscopical Society.

7 CFR 29.1162 - Leaf (B Group).

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf (B Group). 29.1162 Section 29.1162 Agriculture... INSPECTION Standards Grades § 29.1162 Leaf (B Group). This group consists of leaves normally grown at or above the midportion of the stalk. Leaves of the B group have a pointed tip, tend to fold, usually are...

Temperature-sensitive leaf color mutation in rice

International Nuclear Information System (INIS)

Shu Qingyao; Liu Guifu; Xia Yingwu

1996-01-01

Studies on the leaf color appearance of 4 chlorophyll-deficient mutation lines both in field and in phytotron were carried out. The mutation lines were induced by 60 Co gamma rays, and showed that white or yellow leaves at seedling stage were quite different from their-parent 2177 S, a thermal sensitive genie male sterile line and any other rice materials. The temperature had great influence on the expression of leaf color at seedling stage in the mutation lines. the leaf color was white at 30∼35 degree C for the lines W 4 and W 11 . The chlorophyll content of 1.5-leaf-age seedlings was 0.0219 and 0.0536 mg/g FW respectively for W 4 and W 11 at 35 degree C. When the temperature dropped to 20∼25 degree C, the seedlings showed yellow or yellowish and the chlorophyll content reached to 0.2410 and 0.3431 mg/g FW at 25 degree C, respectively. However, the responses to temperature for W 17 and W 25 were just the opposite. They were white at 20∼25 degree C, but appeared greenish at 30∼35 degree C. The chlorophyll content increased from 0.0813 and 0.0172 mg/g FW at 25 degree C to 1.0570 and 1.1367 mg/g FW at 35 degree C for the lines W 1 -7 and W 25 , respectively. The parent line 2177 S showed normal green and the chlorophyll content was between 2.108 and 2.118 mg/g FW. The W 11 is exception, which showed yellow to light green in lifetime, and all the mutation lines could convert to normal green after the extension of the fourth leaf. The chlorophyll content of 3.5-leaf-age W 4 and W 17 seedlings grown under 25 degree C reached to 2.2190 and 1.993 mg/g FW, which was about 86. 6% and 81.1% of that of 2177 S at the same stage. When grown at the temperature bellow 20 degree C, W 25 maintained white and could not changed into green after the 4th leaf extension, and showed a conditional lethal status

Diallel analysis of leaf disease resistance in inbred Brazilian popcorn cultivars.

Science.gov (United States)

Vieira, R A; Scapim, C A; Moterle, L M; Tessmann, D J; Conrado, T V; Amaral Júnior, A T

2009-12-01

We estimated general and specific combining abilities and examined resistance to northern leaf blight (Exserohilum turcicum) and to gray leaf spot (Cercospora zeae-maydis) in a set of nine inbred popcorn lines. These inbreds were crossed in a complete diallel scheme without reciprocals, which produced 36 F(1) hybrids. Two experiments with a square lattice design and three replications were conducted during the 2008/2009 crop season, in Maringá, PR, Brazil. The severity of northern leaf blight and gray leaf spot was assessed under natural infestation conditions. Data were examined by individual and joint analysis of variance. Individual and joint Griffing's diallel analyses were carried out for adjusted means. General combining ability and specific combining ability were significant (P < 0.10) by the F-test for northern leaf blight and gray leaf spot infestation levels. This denotes that additive and non-additive gene effects both contributed to resistance to these diseases, but that the additive gene effects were more important. Among the inbred lines, P(8) and P(9) gave the highest resistance to northern leaf blight, and P(3) and P(4.3) gave the highest resistance to gray leaf spot. The hybrids P(7.4) x P(8) and P(4.3) x P(9) could be exploited by reciprocal recurrent selection to provide genotypes with both northern leaf blight and gray leaf spot resistance. Significant interaction between general combining ability and crop season (P < 0.10) denotes the importance of environment, even though the disease levels in the hybrids were quite consistent.

Novel insect leaf-mining after the end-Cretaceous extinction and the demise of cretaceous leaf miners, Great Plains, USA.

Directory of Open Access Journals (Sweden)

Michael P Donovan

Full Text Available Plant and associated insect-damage diversity in the western U.S.A. decreased significantly at the Cretaceous-Paleogene (K-Pg boundary and remained low until the late Paleocene. However, the Mexican Hat locality (ca. 65 Ma in southeastern Montana, with a typical, low-diversity flora, uniquely exhibits high damage diversity on nearly all its host plants, when compared to all known local and regional early Paleocene sites. The same plant species show minimal damage elsewhere during the early Paleocene. We asked whether the high insect damage diversity at Mexican Hat was more likely related to the survival of Cretaceous insects from refugia or to an influx of novel Paleocene taxa. We compared damage on 1073 leaf fossils from Mexican Hat to over 9000 terminal Cretaceous leaf fossils from the Hell Creek Formation of nearby southwestern North Dakota and to over 9000 Paleocene leaf fossils from the Fort Union Formation in North Dakota, Montana, and Wyoming. We described the entire insect-feeding ichnofauna at Mexican Hat and focused our analysis on leaf mines because they are typically host-specialized and preserve a number of diagnostic morphological characters. Nine mine damage types attributable to three of the four orders of leaf-mining insects are found at Mexican Hat, six of them so far unique to the site. We found no evidence linking any of the diverse Hell Creek mines with those found at Mexican Hat, nor for the survival of any Cretaceous leaf miners over the K-Pg boundary regionally, even on well-sampled, surviving plant families. Overall, our results strongly relate the high damage diversity on the depauperate Mexican Hat flora to an influx of novel insect herbivores during the early Paleocene, possibly caused by a transient warming event and range expansion, and indicate drastic extinction rather than survivorship of Cretaceous insect taxa from refugia.

Novel insect leaf-mining after the end-Cretaceous extinction and the demise of cretaceous leaf miners, Great Plains, USA.

Science.gov (United States)

Donovan, Michael P; Wilf, Peter; Labandeira, Conrad C; Johnson, Kirk R; Peppe, Daniel J

2014-01-01

Plant and associated insect-damage diversity in the western U.S.A. decreased significantly at the Cretaceous-Paleogene (K-Pg) boundary and remained low until the late Paleocene. However, the Mexican Hat locality (ca. 65 Ma) in southeastern Montana, with a typical, low-diversity flora, uniquely exhibits high damage diversity on nearly all its host plants, when compared to all known local and regional early Paleocene sites. The same plant species show minimal damage elsewhere during the early Paleocene. We asked whether the high insect damage diversity at Mexican Hat was more likely related to the survival of Cretaceous insects from refugia or to an influx of novel Paleocene taxa. We compared damage on 1073 leaf fossils from Mexican Hat to over 9000 terminal Cretaceous leaf fossils from the Hell Creek Formation of nearby southwestern North Dakota and to over 9000 Paleocene leaf fossils from the Fort Union Formation in North Dakota, Montana, and Wyoming. We described the entire insect-feeding ichnofauna at Mexican Hat and focused our analysis on leaf mines because they are typically host-specialized and preserve a number of diagnostic morphological characters. Nine mine damage types attributable to three of the four orders of leaf-mining insects are found at Mexican Hat, six of them so far unique to the site. We found no evidence linking any of the diverse Hell Creek mines with those found at Mexican Hat, nor for the survival of any Cretaceous leaf miners over the K-Pg boundary regionally, even on well-sampled, surviving plant families. Overall, our results strongly relate the high damage diversity on the depauperate Mexican Hat flora to an influx of novel insect herbivores during the early Paleocene, possibly caused by a transient warming event and range expansion, and indicate drastic extinction rather than survivorship of Cretaceous insect taxa from refugia.

Leaf Surface Effects on Retrieving Chlorophyll Content from Hyperspectral Remote Sensing

Science.gov (United States)

Qiu, Feng; Chen, JingMing; Ju, Weimin; Wang, Jun; Zhang, Qian

2017-04-01

Light reflected directly from the leaf surface without entering the surface layer is not influenced by leaf internal biochemical content. Leaf surface reflectance varies from leaf to leaf due to differences in the surface roughness features and is relatively more important in strong absorption spectral regions. Therefore it introduces dispersion of data points in the relationship between biochemical concentration and reflectance (especially in the visible region). Separation of surface from total leaf reflection is important to improve the link between leaf pigments content and remote sensing data. This study aims to estimate leaf surface reflectance from hyperspectral remote sensing data and retrieve chlorophyll content by inverting a modified PROSPECT model. Considering leaf surface reflectance is almost the same in the visible and near infrared spectral regions, a surface layer with a reflectance independent of wavelength but varying from leaf to leaf was added to the PROSPECT model. The specific absorption coefficients of pigments were recalibrated. Then the modified model was inverted on independent datasets to check the performance of the model in predicting the chlorophyll content. Results show that differences in estimated surface layer reflectance of various species are noticeable. Surface reflectance of leaves with epicuticular waxes and trichomes is usually higher than other samples. Reconstruction of leaf reflectance and transmittance in the 400-1000 nm wavelength region using the modified PROSPECT model is excellent with low root mean square error (RMSE) and bias. Improvements for samples with high surface reflectance (e.g. maize) are significant, especially for high pigment leaves. Moreover, chlorophyll retrieved from inversion of the modified model is consequently improved (RMSE from 5.9-13.3 ug/cm2 with mean value 8.1 ug/cm2, while mean correlation coefficient is 0.90) compared to results of PROSPECT-5 (RMSE from 9.6-20.2 ug/cm2 with mean value 13

Fire ants protect mealybugs against their natural enemies by utilizing the leaf shelters constructed by the leaf roller Sylepta derogata.

Directory of Open Access Journals (Sweden)

Aiming Zhou

Full Text Available The importance of mutualism is receiving more attention in community ecology. In this study, the fire ant Solenopsis invicta was found to take advantage of the shelters constructed by the leaf roller Sylepta derogata to protect mealybugs (Phenacoccus solenopsis against their natural enemies. This protective effect of fire ant tending on the survival of mealybugs in shelters was observed when enemies and leaf rollers were simultaneously present. Specifically, fire ants moved the mealybugs inside the shelters produced by S. derogata on enemy-infested plants. Compared with that in plants without ants, the survival of mealybugs in shelters in the presence of natural enemies in plants with ants markedly improved. Both the protection of ants and the shelters provided by leaf rollers did not affect the survival of mealybugs in the absence of enemies in plants. Ants and leaf rollers significantly improved the survival of mealybugs in predator-infested plants, whereas no such improvement was observed in parasitoid-infested ones.

Theoretical analysis of radiation field penumbra from a multi leaf collimator

International Nuclear Information System (INIS)

Li Shidong; Boyer, Arthur; Findley, David; Mok, Ed

1996-01-01

Purpose/Objective: Analysis and measurement of the difference between the light field and the radiation field of the multi leaf collimator (MLC) leaves that are constructed with curved ends. Material and Methods: A Varian MLC with curved leaf ends was installed on a Clinac 2300 C/D. The leaves were 6.13 cm deep (dimension in beam direction) and were located 53.9 cm from the x-ray target. The leaf ends had an 8 cm radius of curvature. A relation was derived using three dimensional geometry predicting the location of the light field edge relative to the geometric projection of the tip of the curved leaf end. This is a nonlinear relationship because the shadow of the leaf is generated by different points along the leaf end surface as the leaf moves across the field. The theoretical edge of the radiation fluence for a point source was taken to be located along the projection of a chord whose length was 1 Half-Value Thickness (HVT). The chords having projection points across the light field edge were computed using an analytical solution. The radiation transmission through the leaf end was then estimated. The HVT used for tungsten alloy, the leaf material, was 0.87 cm and 0.94 cm for the 6 MV and 15 MV photon beams, respectively. The location of the projection of the 1 HVT chord at a distance of 100 cm from x-ray target was also a nonlinear function of the projection of the leaf tip. Results: The displacement of the light field edge relative to the projection of the leaf tip varies from 0 mm when the leaf tip projects to the central axis, to approximately 3.2 mm for a 20 cm half-field width. The light field edge was always displaced into the unblocked area. The displacement of the projection of the 1 HVT chord relative to the projection of the leaf tip varies from 0.3 mm on the central axis to 3.0 mm for a 20 cm half-field width. The projection of 1 HVT chord was deviated from the light field edge by only 0.3 mm which would be slightly increased to 0.4 mm on decreasing

Short Communication: The developmentt of a leaf tensilmeter for in ...

African Journals Online (AJOL)

The development of a portable leaf tensilmeter for the in situ measurement of leaf tensile strength is described. Tensile strength is determined by the distortion of strain gauges on modified stripping pliers which are used to break leaf blades. The output is displayed via an analogue chip through a liquid crystal display.

Plant traits and environment: floating leaf blade production and turnover of waterlilies.

Science.gov (United States)

Klok, Peter F; van der Velde, Gerard

2017-01-01

Floating leaf blades of waterlilies fulfill several functions in wetland ecosystems by production, decomposition and turnover as well as exchange processes. Production and turnover rates of floating leaf blades of three waterlily species, Nuphar lutea (L.) Sm., Nymphaea alba L. and Nymphaea candida Presl, were studied in three freshwater bodies, differing in trophic status, pH and alkalinity. Length and percentages of leaf loss of marked leaf blades were measured weekly during the growing season. Area and biomass were calculated based on leaf length and were used to calculate the turnover rate of floating leaf blades. Seasonal changes in floating leaf production showed that values decreased in the order: Nymphaea alba , Nuphar lutea , Nymphaea candida . The highest production was reached for Nuphar lutea and Nymphaea alba in alkaline, eutrophic water bodies. The production per leaf was relatively high for both species in the acid water body. Nymphaea candida showed a very short vegetation period and low turnover rates. The ratio Total potential leaf biomass/Maximum potential leaf biomass (P/B max ) of the three species ranged from 1.35-2.25. The ratio Vegetation period (Period with floating leaves)/Mean leaf life span ranged from 2.94-4.63, the ratio Growth period (Period with appearance of new floating leaves)/Vegetation period from 0.53-0.73. The clear differences between Nymphaea candida versus Nuphar lutea and Nymphaea alba , may be due to adaptations of Nymphaea candida to an Euro-Siberic climate with short-lasting summer conditions.

Incomplete resistance to coffee leaf rust (Hemileia vastatrix)

NARCIS (Netherlands)

Eskes, A.B.

1983-01-01

Incomplete resistance to coffee leaf rust ( Hemileia vastatrix ) may be of value in obtaining durable resistance, which is of great importance for the perennial coffee crop. Methods were developed to assess incomplete resistance to coffee leaf rust by using illustrated scales

cassava brown streak disease effects on leaf metabolites

African Journals Online (AJOL)

USER

Plate 1. Progression of CBSD in cassava leaves with scores 1= leaf from clean plant, no CBSD, 2 = Mild CBSD leaf veinal ... absorb the excess water, after which they were rolled ..... to low carbon dioxide exchange, as observed in sugar cane ...

Leaf gas exchange of mature bottomland oak trees

Science.gov (United States)

Rico M. Gazal; Mark E. Kubiske; Kristina F. Connor

2009-01-01

We determined how changes in environmental moisture affected leaf gas exchange in Nuttall (Quercus texana Buckley), overcup (Q. lyrata Walt.), and dominant and codominant swamp chestnut (Q. michauxii Nutt.) oak trees in Mississippi and Louisiana. We used canopy access towers to measure leaf level gas...

Leaf area estimation of cassava from linear dimensions

Directory of Open Access Journals (Sweden)

SAMARA ZANETTI

2017-08-01

Full Text Available ABSTRACT The objective of this study was to determine predictor models of leaf area of cassava from linear leaf measurements. The experiment was carried out in greenhouse in the municipality of Botucatu, São Paulo state, Brazil. The stem cuttings with 5-7 nodes of the cultivar IAC 576-70 were planted in boxes filled with about 320 liters of soil, keeping soil moisture at field capacity, monitored by puncturing tensiometers. At 80 days after planting, 140 leaves were randomly collected from the top, middle third and base of cassava plants. We evaluated the length and width of the central lobe of leaves, number of lobes and leaf area. The measurements of leaf areas were correlated with the length and width of the central lobe and the number of lobes of the leaves, and adjusted to polynomial and multiple regression models. The linear function that used the length of the central lobe LA = -69.91114 + 15.06462L and linear multiple functions LA = -69.9188 + 15.5102L + 0.0197726K - 0.0768998J or LA = -69.9346 + 15.0106L + 0.188931K - 0.0264323H are suitable models to estimate leaf area of cassava cultivar IAC 576-70.

Isolation, characterization and identification of pericarp-degrading bacteria for the production of off-odour-free white pepper from fresh berries of Piper nigrum L.

Science.gov (United States)

Vinod, V; Kumar, A; Zachariah, T J

2014-04-01

To isolate, fermentatively evaluate and identify black pepper (Piper nigrum L.)-associated bacteria for the microbial decortication of fresh ripened berries and dried black pepper for preparation of off-odour-free white pepper. Among 45 bacterial isolates obtained from black pepper, seven of them were found to decorticate black pepper (>60%) and fresh pepper berries (98-100%) into white pepper within 5 days of immersion in bacterial suspension. The 16S rRNA genes (1500-bp amplicon) of these bacteria were sequenced, and species identity was established by closest match in GenBank. Superior-quality white pepper was obtained with Bacillus subtilis (IISR WP 33, 34, 38), Bacillus licheniformis (IISR WP 43), Acinetobacter baumanii (IISR WP 35), Klebsiella pneumoniae (IISR WP 19) and Microbacterium barkeri (IISR WP25). The bacterial isolates were found to secrete multiple hydrolytic enzymes such as cellulase, pectinase, amylase, protease and xylanase. Bacterial cultures were deposited with International Depository Authority at Microbial Type Culture Collection, India, as patent deposits as prescribed in Budapest Treaty for microbial deposits. The white pepper, thus obtained from bacterial decortication process, was free from off-odour compound, especially skatole. Other biochemical constituents such as oleoresin, piperine and essential oils were found in the acceptable range. The bacterial decortication did not affect inherent constituents of pepper such as essential oil constituents, oleoresin and piperine content. One of the most significant findings of the work is identification of specific bacterial species for decortication of fresh berries or black pepper berries into value-added white pepper. This work paved way for developing a technological process for microbial decortication of fresh/black pepper for the production of superior-quality white pepper. © 2014 The Society for Applied Microbiology.

Sorption of lead from aqueous solutions by spent tea leaf | Yoshita ...

African Journals Online (AJOL)

Pb) from solution. The Pb removal by the spent tea leaf adsorbent depended on pretreatment of spent tea leaf, adsorption contact time and adsorbent dosage. The optimum pretreatment conditions were confirmed to be that tea leaf was ground ...

Leaf appearance rate and final main stem leaf number as affected by temperature and photoperiod in cereals grown in Mediterranean environment

Directory of Open Access Journals (Sweden)

Ezio Riggi

2017-09-01

Full Text Available In the present study, a two-year field trial was carried out with the aim to evaluate daylength and air temperature effects on leaf appearance and related rates in two durum wheat (Triticum durum Desf., two bread wheat (Triticum aestivum L. and two barley (Hordeum vulgare L. cultivars, using six different sowing dates (SD. Significant effects of SD on final main stem leaf number (FLN, thermal leaf appearance rate (TLAR, daily leaf appearance rate (DLAR and phyllochron (PhL were found. Cultivars resulted inversely correlated to mean air temperature in the interval emergence - fifth leaf full expansion (E-V. Linear response of leaf number over days after sowing was shown for all SD and cultivars, with R2 higher than 0.95. FLN linearly decreased from the first to the last SD for durum wheat, while more variable behaviour was observed in bread wheat. TLAR and DLAR showed a linear increment of the rate from the first to the last SD in durum wheat, while did not for bread wheat and barley. PhL in durum wheat decreased from the first to the last SD. Barley and bread wheat showed the highest values on those SDs which did not reach flowering. The increase of TLAR was affected by photoperiod and photothermal units in durum wheat, while by temperatures only in barley and bread wheat. Present results might find practical application in the improvement of phenology simulation models for durum wheat, bread wheat and barley grown in Mediterranean area in absence of water and nutrient stress.

Non-destructive linear model for leaf area estimation in Vernonia ferruginea Less

Directory of Open Access Journals (Sweden)

MC. Souza

Full Text Available Leaf area estimation is an important biometrical trait for evaluating leaf development and plant growth in field and pot experiments. We developed a non-destructive model to estimate the leaf area (LA of Vernonia ferruginea using the length (L and width (W leaf dimensions. Different combinations of linear equations were obtained from L, L2, W, W2, LW and L2W2. The linear regressions using the product of LW dimensions were more efficient to estimate the LA of V. ferruginea than models based on a single dimension (L, W, L2 or W2. Therefore, the linear regression “LA=0.463+0.676WL” provided the most accurate estimate of V. ferruginea leaf area. Validation of the selected model showed that the correlation between real measured leaf area and estimated leaf area was very high.

Leaf life span plasticity in tropical seedlings grown under contrasting light regimes.

Science.gov (United States)

Vincent, Gregoire

2006-02-01

The phenotypic plasticity of leaf life span in response to low resource conditions has a potentially large impact on the plant carbon budget, notably in evergreen species not subject to seasonal leaf shedding, but has rarely been well documented. This study evaluates the plasticity of leaf longevity, in terms of its quantitative importance to the plant carbon balance under limiting light. Seedlings of four tropical tree species with contrasting light requirements (Alstonia scholaris, Hevea brasiliensis, Durio zibethinus and Lansium domesticum) were grown under three light regimes (full sunlight, 45 % sunlight and 12 % sunlight). Their leaf dynamics were monitored over 18 months. All species showed a considerable level of plasticity with regard to leaf life span: over the range of light levels explored, the ratio of the range to the mean value of life span varied from 29 %, for the least plastic species, to 84 %, for the most. The common trend was for leaf life span to increase with decreasing light intensity. The plasticity apparent in leaf life span was similar in magnitude to the plasticity observed in specific leaf area and photosynthetic rate, implying that it has a significant impact on carbon gain efficiency when plants acclimate to different light regimes. In all species, median survival time was negatively correlated with leaf photosynthetic capacity (or its proxy, the nitrogen content per unit area) and leaf emergence rate. Longer leaf life spans under low light are likely to be a consequence of slower ageing as a result of a slower photosynthetic metabolism.

Linkage between canopy water storage and drop size distributions of leaf drips

Science.gov (United States)

Nanko, Kazuki; Watanabe, Ai; Hotta, Norifumi; Suzuki, Masakazu

2013-04-01

Differences in drop size distribution (DSD) of leaf drips among tree species have been estimated and physically interpreted to clarify the leaf drip generation process. Leaf drip generation experiments for nine species were conducted in an indoor location without foliage vibration using an automatic mist spray. Broad-leaved species produced a similar DSD among species whose leaves had a matte surface and a second similar DSD among species whose leaves had a coated surface. The matte broad leaves produced a larger and wider range of DSDs than the coated broad leaves. Coated coniferous needles had a wider range of DSDs than the coated broad leaves and different DSDs were observed for different species. The species with shorter dense needles generated a larger DSD. The leaf drip diameter was calculated through the estimation of a state of equilibrium of a hanging drop on the leaves based on physical theory. The calculations indicated that the maximum diameter of leaf drips was determined by the contact angle, and the range of DSDs was determined by the variation in contact length and the contact diameter at the hanging points. The results revealed that leaf drip DSD changed due to variations in leaf hydrophobicity, leaf roughness, leaf geometry and leaf inclination among the different tree species. This study allows the modelization of throughfall DSD. Furthermore, it indicates the possibility of interpreting canopy water processes from canopy water storage to drainage through the contact angle and leaf drip DSD. The part of this study is published in Nanko et al. (2013, Agric. Forest. Meteorol. 169, 74-84).

Plant traits and environment: floating leaf blade production and turnover of waterlilies

Directory of Open Access Journals (Sweden)

Peter F. Klok

2017-04-01

Full Text Available Floating leaf blades of waterlilies fulfill several functions in wetland ecosystems by production, decomposition and turnover as well as exchange processes. Production and turnover rates of floating leaf blades of three waterlily species, Nuphar lutea (L. Sm., Nymphaea alba L. and Nymphaea candida Presl, were studied in three freshwater bodies, differing in trophic status, pH and alkalinity. Length and percentages of leaf loss of marked leaf blades were measured weekly during the growing season. Area and biomass were calculated based on leaf length and were used to calculate the turnover rate of floating leaf blades. Seasonal changes in floating leaf production showed that values decreased in the order: Nymphaea alba, Nuphar lutea, Nymphaea candida. The highest production was reached for Nuphar lutea and Nymphaea alba in alkaline, eutrophic water bodies. The production per leaf was relatively high for both species in the acid water body. Nymphaea candida showed a very short vegetation period and low turnover rates. The ratio Total potential leaf biomass/Maximum potential leaf biomass (P/Bmax of the three species ranged from 1.35–2.25. The ratio Vegetation period (Period with floating leaves/Mean leaf life span ranged from 2.94–4.63, the ratio Growth period (Period with appearance of new floating leaves/Vegetation period from 0.53–0.73. The clear differences between Nymphaea candida versus Nuphar lutea and Nymphaea alba, may be due to adaptations of Nymphaea candida to an Euro-Siberic climate with short-lasting summer conditions.

Effects of combination of leaf resources on competition in container mosquito larvae.

Science.gov (United States)

Reiskind, M H; Zarrabi, A A; Lounibos, L P

2012-08-01

Resource diversity is critical to fitness in many insect species, and may determine the coexistence of competitive species and the function of ecosystems. Plant material provides the nutritional base for numerous aquatic systems, yet the consequences of diversity of plant material have not been studied in aquatic container systems important for the production of mosquitoes. To address how diversity in leaf detritus affects container-inhabiting mosquitoes, we examined how leaf species affect competition between two container inhabiting mosquito larvae, Aedes aegypti and Aedes albopictus, that co-occur in many parts of the world. We tested the hypotheses that leaf species changes the outcome of intra- and interspecific competition between these mosquito species, and that combinations of leaf species affect competition in a manner not predictable based upon the response to each leaf species alone (i.e. the response to leaf combinations is non-additive). We find support for our first hypothesis that leaf species can affect competition, evidence that, in general, leaf combination alters competitive interactions, and no support that leaf combination impacts interspecific competition differently than intraspecific competition. We conclude that combinations of leaves increase mosquito production non-additively such that combinations of leaves act synergistically, in general, and result in higher total yield of adult mosquitoes in most cases, although certain leaf combinations for A. albopictus are antagonistic. We also conclude that leaf diversity does not have a different effect on interspecific competition between A. aegypti and A. albopictus, relative to intraspecific competition for each mosquito.

7 CFR 29.2662 - Heavy Leaf (B Group).

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Heavy Leaf (B Group). 29.2662 Section 29.2662 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS TOBACCO INSPECTION Standards Grades § 29.2662 Heavy Leaf (B Group). This group consists of leaves...

Coconut leaf bioactivity toward generalist maize insect pests

Science.gov (United States)

Tropical plants are often more resistant to insects than temperate plants due to evolution of robust defenses to cope with a more constant insect threat. Coconut (Cocos nucifera L.) has very few chewing leaf feeding insect pests and was tested against two omnivorous leaf feeding caterpillar species,...

Nutritive evaluation of Telfairia occidentalis leaf protein concentrate ...

African Journals Online (AJOL)

Leaf meal (LM), leaf proteins concentrate (LPC) and LPC residues from Telfairia occidentalis were produced, chemically characterized and the protein quality of the LPC evaluated using rats. Five infant weaning foods were formulated using varying combinations of T. occidentalis LPC and soybean meal. These foods were ...

Peach leaf responses to soil and cement dust pollution.

Science.gov (United States)

Maletsika, Persefoni A; Nanos, George D; Stavroulakis, George G

2015-10-01

Dust pollution can negatively affect plant productivity in hot, dry and with high irradiance areas during summer. Soil or cement dust were applied on peach trees growing in a Mediterranean area with the above climatic characteristics. Soil and cement dust accumulation onto the leaves decreased the photosynthetically active radiation (PAR) available to the leaves without causing any shade effect. Soil and mainly cement dust deposition onto the leaves decreased stomatal conductance, photosynthetic and transpiration rates, and water use efficiency due possibly to stomatal blockage and other leaf cellular effects. In early autumn, rain events removed soil dust and leaf functions partly recovered, while cement dust created a crust partially remaining onto the leaves and causing more permanent stress. Leaf characteristics were differentially affected by the two dusts studied due to their different hydraulic properties. Leaf total chlorophyll decreased and total phenol content increased with dust accumulation late in the summer compared to control leaves due to intense oxidative stress. The two dusts did not cause serious metal imbalances to the leaves, except of lower leaf K content.

Evaluating a tobacco leaf humidification system involving nebulisation

Directory of Open Access Journals (Sweden)

Néstor Enrique Cerquera Peña

2010-05-01

Full Text Available A tobacco leaf humidifying system involving nebulisation was designned, implemented and evaluated; it had a system for monitoring and recording environmental conditions thereby producing an environment having more homogeneous relative humidity, ensuring better water use, better control of relative humidity and better control in managing cured tobacco leaf moisture content, thereby leading to a consequent improvement in final product quality. 55% to 75% relative humidity and 4 to 6 hour working ranges were obtained to en- sure leaf humidification reached 16% humidity on a wet basis. Two new designs are proposed for the conditioning stage regarding this conditioning chamber’s operational management, based on the results and field observations, which would allow better leaf management, thereby avoiding the risk of losses due to manipulation and over-humidification. This work strengthens research in the field of tobacco pos- tharvest technology, complementing other research projects which have been carried out in Colombia.

Sugarbeet leaf spot disease (Cercospora beticola Sacc.)dagger.

Science.gov (United States)

Weiland, John; Koch, Georg

2004-05-01

SUMMARY Leaf spot disease caused by Cercospora beticola Sacc. is the most destructive foliar pathogen of sugarbeet worldwide. In addition to reducing yield and quality of sugarbeet, the control of leaf spot disease by extensive fungicide application incurs added costs to producers and repeatedly has selected for fungicide-tolerant C. beticola strains. The genetics and biochemistry of virulence have been examined less for C. beticola as compared with the related fungi C. nicotianae, C. kikuchii and C. zeae-maydis, fungi to which the physiology of C. beticola is often compared. C. beticola populations generally are not characterized as having race structure, although a case of race-specific resistance in sugarbeet to C. beticola has been reported. Resistance currently implemented in the field is quantitatively inherited and exhibits low to medium heritability. Cercospora beticola Sacc.; Kingdom Fungi, Subdivision Deuteromycetes, Class Hyphomycetes, Order Hyphales, Genus Cercospora. Circular, brown to red delimited spots with ashen-grey centre, 0.5-6 mm diameter; dark brown to black stromata against grey background; pale brown unbranched sparingly septate conidiophores, hyaline acicular conidia, multiseptate, from 2.5 to 4 microm wide and 50-200 microm long. Propagative on Beta vulgaris and most species of Beta. Reported on members of the Chenopodiaceae and on Amaranthus. Disease symptoms: Infected leaves and petioles of B. vulgaris exhibit numerous circular leaf spots that coalesce in severe cases causing complete leaf collapse. Dark specks within a grey spot centre are characteristic for the disease. Older leaves exhibit a greater number of lesions with larger spot diameter. During the latter stage of severe epiphytotics, new leaf growth can be seen emerging from the plant surrounded by prostrate, collapsed leaves. Fungicides in the benzimidazole and triazole class as well as organotin derivatives and strobilurins have successfully been used to control Cercospora

Responses of rubber leaf phenology to climatic variations in Southwest China

Science.gov (United States)

Zhai, De-Li; Yu, Haiying; Chen, Si-Chong; Ranjitkar, Sailesh; Xu, Jianchu

2017-11-01

The phenology of rubber trees (Hevea brasiliensis) could be influenced by meteorological factors and exhibits significant changes under different geoclimates. In the sub-optimal environment in Xishuangbanna, rubber trees undergo lengthy periods of defoliation and refoliation. The timing of refoliation from budburst to leaf aging could be affected by powdery mildew disease (Oidium heveae), which negatively impacts seed and latex production. Rubber trees are most susceptible to powdery mildew disease at the copper and leaf changing stages. Understanding and predicting leaf phenology of rubber trees are helpful to develop effective means of controlling the disease. This research investigated the effect of several meteorological factors on different leaf phenological stages in a sub-optimal environment for rubber cultivation in Jinghong, Yunnan in Southwest China. Partial least square regression was used to quantify the relationship between meteorological factors and recorded rubber phenologies from 2003 to 2011. Minimum temperature in December was found to be the critical factor for the leaf phenology development of rubber trees. Comparing the delayed effects of minimum temperature, the maximum temperature, diurnal temperature range, and sunshine hours were found to advancing leaf phenologies. A comparatively lower minimum temperature in December would facilitate the advancing of leaf phenologies of rubber trees. Higher levels of precipitation in February delayed the light green and the entire process of leaf aging. Delayed leaf phenology was found to be related to severe rubber powdery mildew disease. These results were used to build predictive models that could be applied to early warning systems of rubber powdery mildew disease.

Phenotypic characterization and inheritance of two foliar mutants in pea (Pisum Sativum L.): 'Reduced leaf size' and 'Orange leaf'

International Nuclear Information System (INIS)

Naidenova, N.; Vassilevska-Ivanova, R.; Tcekova, Z.

2003-01-01

Two foliar pea (Pisum sativum L.) mutants characterized by reduced leaf size (2/978) and orange leaf (2/1409 M) were established. Both mutants were described morphologically and their productivity potential , pollen viability and inheritance of the mutant traits were evaluated. The mutant 2/978 was identified after irradiation of dry seeds from cv Borek with 15 Gy fast neutrons and was related to the leaf mutation 'rogue'. Reciprocal crosses between mutant 2/978 and cv Borel were executed, and F 1 and F 2 generations were analyzed. The altered leaf trait was presented in all F 1 plants suggesting a dominant character. F 2 segregation data indicated that the trait was controlled by a single dominant gene. The mutant 2/1409M originated from the mutant 2/978 after irradiation with 50 Gy γ-rays. The main mutant's phenotypic characteristic was the orange-yellow coloration of leaves and plants. After of series of crosses it was established that induced chlorophyll mutation is monogenic, recessive and both mutant traits are independently inherited. Two mutants could be used as appropriate plant material for genetic and biological investigations

Hyperbolic projections of siemens 3d-mlc leaf paths

International Nuclear Information System (INIS)

Menzies, N.

2004-01-01

Full text: The Siemens Primus linear accelerator has the option of being fitted with a multi-leaf collimator (3D-MLC) that is marketed as having 'double focus', to achieve a constant dose penumbra for all leaf settings. This is achieved by moving the leaves through arcs (similar to some conventional collimator jaws), as well as shaping the leaf side-faces as divergent planes from the x-ray source. One consequence of the mechanical design of the 3D-MLC is that as individual leaves are moved, their projections from the light / x-ray source to the treatment plane follow paths that are hyperbolic, as shown in the figure below. (The eccentricity of the hyperbola is a function of leaf number / distance from centre.) The trajectories of the MLC leaves were modelled (in a spreadsheet) using geometrical projections of the MLC leaves to the treatment plane, with construction details provided in Siemens documentation. The results were checked against the image of the leaf in the linac light field. This problem belongs to the class of conic sections in mathematics, where the intersection of a plane with both nappes of a double right circular cone results in a hyperbola. The good agreement between the model and the light field image provided confirmation of the MLC construction details. AS/NZS 4434.1:1996 (reproduced from IEC 976:1989) provides specifications for maximum deviation from orthogonality of adjacent edges, which can be interpreted for MLC collimators to parallelism of the direction of leaf travel and the adjacent collimator edge (e.g. Elekta ATS). However for the Siemens 'double focused' MLC, it is demonstrated that the geometrical construction of the MLC militates against the leaf image being used for this kind of test. It is also demonstrated that at last one commercial treatment planning system models the Siemens leaf trajectories linearly. The clinical significance of the error in this model is shown to be negligible. Copyright (2004) Australasian College of

Proximate Analysis Of Castor Seeds And Cake | Annongu | Journal ...

African Journals Online (AJOL)

Amino acid profile analysis of un-decorticated and decorticated seed and cake compared with soybeans as standard plant protein indicated that the cake is deficient in some indispensable amino acids like lysine (4.11), iso-leucine (3.09), tryptophan (0) compared with 6.30, 7.90 and 1.30 lysine, iso-leucine and tryptopha in ...

Treatment of Osteomyelitis: A Case for Disruption of the Affected Adjacent Periosteum.

Science.gov (United States)

Hudson, John W; Daly, Austin P; Foster, Michael

2017-10-01

To evaluate the response of mandibular osteomyelitis treated by surgical decortication with disruption of the affected adjacent periosteum in concert with long-term targeted antibiotic therapy. The hypothesis is that, by removing the buccal cortical plate and disrupting the hypertrophically inflamed adjacent periosteum, the medullary bone will be brought in contact with bleeding tissue and circulating immunologic factors and antibiotics, which will promote definitive resolution. A retrospective review was conducted of 7 patient charts with associated radiographs from November 2010 to August 2016 treated by the first author at the University of Tennessee Medical Center (Knoxville, TN). Patients with chronic suppurative or nonsuppurative osteomyelitis of the mandible without condylar involvement or pathologic fracture were selected and treated with decortication with periosteal disruption in combination with long-term targeted antibiotic therapy. Seven patients (3 women and 4 men; mean age, 60 yr) underwent decortication with periosteal disruption of the affected area and received at least 6 weeks of targeted intravenous antibiotics. Computed tomography was performed preoperatively and a repeat study was performed after completion of antibiotics. In each case, post-treatment imaging showed definitive resolution after treatment with decortication in concert with disruption of the inflamed hypertrophic periosteum and intravenous antibiotics. Debridement of the infected cortical bone with restoration of the blood supply through disruption of the adjacent periosteum provided definitive resolution of mandibular osteomyelitis in the 7 patients treated. The hypothesis is that disruption of the affected adjacent periosteum reintroduces an immune-mediated response in concert with improved antibiotic delivery to and penetrance of the diseased mandible, aiding in definitive resolution. Decortication with periosteal disruption allows for preservation of the inferior alveolar

Role of soil-to-leaf tritium transfer in controlling leaf tritium dynamics: Comparison of experimental garden and tritium-transfer model results.

Science.gov (United States)

Ota, Masakazu; Kwamena, Nana-Owusua A; Mihok, Steve; Korolevych, Volodymyr

2017-11-01

Environmental transfer models assume that organically-bound tritium (OBT) is formed directly from tissue-free water tritium (TFWT) in environmental compartments. Nevertheless, studies in the literature have shown that measured OBT/HTO ratios in environmental samples are variable and generally higher than expected. The importance of soil-to-leaf HTO transfer pathway in controlling the leaf tritium dynamics is not well understood. A model inter-comparison of two tritium transfer models (CTEM-CLASS-TT and SOLVEG-II) was carried out with measured environmental samples from an experimental garden plot set up next to a tritium-processing facility. The garden plot received one of three different irrigation treatments - no external irrigation, irrigation with low tritium water and irrigation with high tritium water. The contrast between the results obtained with the different irrigation treatments provided insights into the impact of soil-to-leaf HTO transfer on the leaf tritium dynamics. Concentrations of TFWT and OBT in the garden plots that were not irrigated or irrigated with low tritium water were variable, responding to the arrival of the HTO-plume from the tritium-processing facility. In contrast, for the plants irrigated with high tritium water, the TFWT concentration remained elevated during the entire experimental period due to a continuous source of high HTO in the soil. Calculated concentrations of OBT in the leaves showed an initial increase followed by quasi-equilibration with the TFWT concentration. In this quasi-equilibrium state, concentrations of OBT remained elevated and unchanged despite the arrivals of the plume. These results from the model inter-comparison demonstrate that soil-to-leaf HTO transfer significantly affects tritium dynamics in leaves and thereby OBT/HTO ratio in the leaf regardless of the atmospheric HTO concentration, only if there is elevated HTO concentrations in the soil. The results of this work indicate that assessment models

Automated rice leaf disease detection using color image analysis

Science.gov (United States)

Pugoy, Reinald Adrian D. L.; Mariano, Vladimir Y.

2011-06-01

In rice-related institutions such as the International Rice Research Institute, assessing the health condition of a rice plant through its leaves, which is usually done as a manual eyeball exercise, is important to come up with good nutrient and disease management strategies. In this paper, an automated system that can detect diseases present in a rice leaf using color image analysis is presented. In the system, the outlier region is first obtained from a rice leaf image to be tested using histogram intersection between the test and healthy rice leaf images. Upon obtaining the outlier, it is then subjected to a threshold-based K-means clustering algorithm to group related regions into clusters. Then, these clusters are subjected to further analysis to finally determine the suspected diseases of the rice leaf.

Strigolactone Regulates Leaf Senescence in Concert with Ethylene in Arabidopsis.

Science.gov (United States)

Ueda, Hiroaki; Kusaba, Makoto

2015-09-01

Leaf senescence is not a passive degenerative process; it represents a process of nutrient relocation, in which materials are salvaged for growth at a later stage or to produce the next generation. Leaf senescence is regulated by various factors, such as darkness, stress, aging, and phytohormones. Strigolactone is a recently identified phytohormone, and it has multiple functions in plant development, including repression of branching. Although strigolactone is implicated in the regulation of leaf senescence, little is known about its molecular mechanism of action. In this study, strigolactone biosynthesis mutant strains of Arabidopsis (Arabidopsis thaliana) showed a delayed senescence phenotype during dark incubation. The strigolactone biosynthesis genes MORE AXIALLY GROWTH3 (MAX3) and MAX4 were drastically induced during dark incubation and treatment with the senescence-promoting phytohormone ethylene, suggesting that strigolactone is synthesized in the leaf during leaf senescence. This hypothesis was confirmed by a grafting experiment using max4 as the stock and Columbia-0 as the scion, in which the leaves from the Columbia-0 scion senesced earlier than max4 stock leaves. Dark incubation induced the synthesis of ethylene independent of strigolactone. Strigolactone biosynthesis mutants showed a delayed senescence phenotype during ethylene treatment in the light. Furthermore, leaf senescence was strongly accelerated by the application of strigolactone in the presence of ethylene and not by strigolactone alone. These observations suggest that strigolactone promotes leaf senescence by enhancing the action of ethylene. Thus, dark-induced senescence is regulated by a two-step mechanism: induction of ethylene synthesis and consequent induction of strigolactone synthesis in the leaf. © 2015 American Society of Plant Biologists. All Rights Reserved.

Computer aided FEA simulation of EN45A parabolic leaf spring

Directory of Open Access Journals (Sweden)

Krishan Kumar

2013-04-01

Full Text Available This paper describes computer aided finite element analysis of parabolic leaf spring. The present work is an improvement in design of EN45A parabolic leaf spring used by a light commercial automotive vehicle. Development of a leaf spring is a long process which requires lots of test to validate the design and manufacturing variables. A three-layer parabolic leaf spring of EN45A has been taken for this work. The thickness of leaves varies from center to the outer side following a parabolic pattern. These leaf springs are designed to become lighter, but also provide a much improved ride to the vehicle through a reduction on interleaf friction. The CAD modeling of parabolic leaf spring has been done in CATIA V5 and for analysis the model is imported in ANSYS-11 workbench. The finite element analysis (FEA of the leaf spring has been carried out by initially discretizing the model into finite number of elements and nodes and then applying the necessary boundary conditions. Maximum displacement, directional displacement, equivalent stress and weight of the assembly are the output targets of this analysis for comparison & validation of the work.

Correlated evolution of stem and leaf hydraulic traits in Pereskia (Cactaceae).

Science.gov (United States)

Edwards, Erika J

2006-01-01

Recent studies have demonstrated significant correlations between stem and leaf hydraulic properties when comparing across species within ecological communities. This implies that these traits are co-evolving, but there have been few studies addressing plant water relations within an explicitly evolutionary framework. This study tests for correlated evolution among a suite of plant water-use traits and environmental parameters in seven species of Pereskia (Cactaceae), using phylogenetically independent contrasts. There were significant evolutionary correlations between leaf-specific xylem hydraulic conductivity, Huber Value, leaf stomatal pore index, leaf venation density and leaf size, but none of these traits appeared to be correlated with environmental water availability; only two water relations traits - mid-day leaf water potentials and photosynthetic water use efficiency - correlated with estimates of moisture regime. In Pereskia, it appears that many stem and leaf hydraulic properties thought to be critical to whole-plant water use have not evolved in response to habitat shifts in water availability. This may be because of the extremely conservative stomatal behavior and particular rooting strategy demonstrated by all Pereskia species investigated. These results highlight the need for a lineage-based approach to understand the relative roles of functional traits in ecological adaptation.

The leaf phenophase of deciduous species altered by land pavements

Science.gov (United States)

Chen, Yuanyuan; Wang, Xiaoke; Jiang, Bo; Li, Li

2018-02-01

It has been widely reported that the urban environment alters leaf and flowering phenophases; however, it remains unclear if land pavement is correlated with these alterations. In this paper, two popular deciduous urban trees in northern China, ash (Fraxinus chinensis) and maple (Acer truncatum), were planted in pervious and impervious pavements at three spacings (0.5 m × 0.5 m, 1.0 m × 1.0 m, and 2.0 m × 2.0 m apart). The beginning and end dates of the processes of leaf budburst and senescence were recorded in spring and fall of 2015, respectively. The results show that leaf budburst and senescence were significantly advanced in pavement compared to non-pavement lands. The date of full leaf budburst was earlier by 0.7-9.3 days for ash and by 0.3-2.3 days for maple under pavements than non-pavements, respectively. As tree spacing increases, the advanced days of leaf budburst became longer. Our results clearly indicate that alteration of leaf phenophases is attributed to land pavement, which should be taken into consideration in urban planning and urban plant management.

[Spectrum Variance Analysis of Tree Leaves Under the Condition of Different Leaf water Content].

Science.gov (United States)

Wu, Jian; Chen, Tai-sheng; Pan, Li-xin

2015-07-01

Leaf water content is an important factor affecting tree spectral characteristics. So Exploring the leaf spectral characteristics change rule of the same tree under the condition of different leaf water content and the spectral differences of different tree leaves under the condition of the same leaf water content are not only the keys of hyperspectral vegetation remote sensing information identification but also the theoretical support of research on vegetation spectrum change as the differences in leaf water content. The spectrometer was used to observe six species of tree leaves, and the reflectivity and first order differential spectrum of different leaf water content were obtained. Then, the spectral characteristics of each tree species leaves under the condition of different leaf water content were analyzed, and the spectral differences of different tree species leaves under the condition of the same leaf water content were compared to explore possible bands of the leaf water content identification by hyperspectral remote sensing. Results show that the spectra of each tree leaf have changed a lot with the change of the leaf water content, but the change laws are different. Leaf spectral of different tree species has lager differences in some wavelength range under the condition of same leaf water content, and it provides some possibility for high precision identification of tree species.

Natural Pineapple Leaf Fibre Extraction On Josapine And Morris

OpenAIRE

Mazalan Muhammad Firdaus; Yusof Yusri

2017-01-01

The pineapple’s leaf plant contains approximately 2.5% to 3.5% of strong white silky fibres. These fibres are useful and can be extracted from the leaves. There are a few ways to extract the fibre such as hand scrapping and by extraction machine. The objective of this research is to study the quality of fibre extraction by using different age of pineapple leaf. Next, the study aims to compare the quality of Josapine and Morris pineapple leaf with tensile test. Fibre yield percentage are calcu...

Leaf processing behaviour in Atta leafcutter ants: 90% of leaf cutting takes place inside the nest, and ants select pieces that require less cutting.

Science.gov (United States)

Garrett, Ryan W; Carlson, Katherine A; Goggans, Matthew Scott; Nesson, Michael H; Shepard, Christopher A; Schofield, Robert M S

2016-01-01

Leafcutter ants cut trimmings from plants, carry them to their underground nests and cut them into smaller pieces before inoculating them with a fungus that serves as a primary food source for the colony. Cutting is energetically costly, so the amount of cutting is important in understanding foraging energetics. Estimates of the cutting density, metres of cutting per square metre of leaf, were made from samples of transported leaf cuttings and of fungal substrate from field colonies of Atta cephalotes and Atta colombica. To investigate cutting inside the nest, we made leaf-processing observations of our laboratory colony, A. cephalotes. We did not observe the commonly reported reduction of the leaf fragments into a pulp, which would greatly increase the energy cost of processing. Video clips of processing behaviours, including behaviours that have not previously been described, are linked. An estimated 2.9 (±0.3) km of cutting with mandibles was required to reduce a square metre of leaf to fungal substrate. Only about 12% (±1%) of this cutting took place outside of the nest. The cutting density and energy cost is lower for leaf material with higher ratios of perimeter to area, so we tested for, and found that the laboratory ants had a preference for leaves that were pre-cut into smaller pieces. Estimates suggest that the energy required to transport and cut up the leaf material is comparable to the metabolic energy available from the fungus grown on the leaves, and so conservation of energy is likely to be a particularly strong selective pressure for leafcutter ants.

QTL mapping of flag leaf-related traits in wheat (Triticum aestivum L.).

Science.gov (United States)

Liu, Kaiye; Xu, Hao; Liu, Gang; Guan, Panfeng; Zhou, Xueyao; Peng, Huiru; Yao, Yingyin; Ni, Zhongfu; Sun, Qixin; Du, Jinkun

2018-04-01

QTL controlling flag leaf length, flag leaf width, flag leaf area and flag leaf angle were mapped in wheat. This study aimed to advance our understanding of the genetic mechanisms underlying morphological traits of the flag leaves of wheat (Triticum aestivum L.). A recombinant inbred line (RIL) population derived from ND3331 and the Tibetan semi-wild wheat Zang1817 was used to identify quantitative trait loci (QTLs) controlling flag leaf length (FLL), flag leaf width (FLW), flag leaf area (FLA), and flag leaf angle (FLANG). Using an available simple sequence repeat genetic linkage map, 23 putative QTLs for FLL, FLW, FLA, and FLANG were detected on chromosomes 1B, 2B, 3A, 3D, 4B, 5A, 6B, 7B, and 7D. Individual QTL explained 4.3-68.52% of the phenotypic variance in different environments. Four QTLs for FLL, two for FLW, four for FLA, and five for FLANG were detected in at least two environments. Positive alleles of 17 QTLs for flag leaf-related traits originated from ND3331 and 6 originated from Zang1817. QTLs with pleiotropic effects or multiple linked QTL were also identified on chromosomes 1B, 4B, and 5A; these are potential target regions for fine-mapping and marker-assisted selection in wheat breeding programs.

Evaluation of leaf energy dissipation by the Photochemical Reflectance

Science.gov (United States)

Raddi, S.; Magnani, F.

Starting from the early paper by Heber (1969), several studies have demonstrated a subtle shift in leaf spectroscopic characteristics (both absorbance and reflectance) in response to rapid changes in environmental conditions. More recent work, briefly reviewed here, has also demonstrated the existence of two components in the maked peak centered at 505-540 nm: an irreversible component, attributed to the interconversion of leaf xanthophylls, and a reversible component at slightly longer wavelengths, resulting from conformational changes induced by the buildup of a pH gradient across the thylakoid membrane associated with photosynthetic electron transport. Both processes (xanthophyll de-epoxidation and conformational changes) are known to contribute to the dissipation of excess energy in Photosystem II (PSII). Leaf spectroscopy could therefore provide a powerful non-invasive tool for the determination of leaf photosynthetic processes. This led to the development of the normalized spectral index PRI (Photochemical Reflectance Index; Gamon, Penuelas &Field 1992; Gamon, Serrano &Surfus 1997), which relates the functional signal at 531 nm to a reference signal at 570 nm. The index has been found to track diurnal changes in xanthophyll de-epoxidation state, radiation use efficiency and fluorescence in response to light, both at the leaf and more recently at the canopy level. A common relationship has also beenreported across species and functional types, although such a generality has not always been confirmed. Recent reports (Stylinski et al. 2000) have also hinted of a possible link between PRI and leaf photosynthetic potential, possibly through the correlation between xanthophyll content and electron transport machinery in the chloroplast. Such a link, if confirmed, could prove very useful for the remote sensing and modelling ofvegetation. Some of these open questions were addressed in the present study. The correlation between leaf function and reflectance was

Translational researches on leaf senescence for enhancing plant productivity and quality.

Science.gov (United States)

Guo, Yongfeng; Gan, Su-Sheng

2014-07-01

Leaf senescence is a very important trait that limits yield and biomass accumulation of agronomic crops and reduces post-harvest performance and the nutritional value of horticultural crops. Significant advance in physiological and molecular understanding of leaf senescence has made it possible to devise ways of manipulating leaf senescence for agricultural improvement. There are three major strategies in this regard: (i) plant hormone biology-based leaf senescence manipulation technology, the senescence-specific gene promoter-directed IPT system in particular; (ii) leaf senescence-specific transcription factor biology-based technology; and (iii) translation initiation factor biology-based technology. Among the first strategy, the P SAG12 -IPT autoregulatory senescence inhibition system has been widely explored and successfully used in a variety of plant species for manipulating senescence. The vast majority of the related research articles (more than 2000) showed that crops harbouring the autoregulatory system displayed a significant delay in leaf senescence without any abnormalities in growth and development, a marked increase in grain yield and biomass, dramatic improvement in horticultural performance, and/or enhanced tolerance to drought stress. This technology is approaching commercialization. The transcription factor biology-based and translation initiation factor biology-based technologies have also been shown to be very promising and have great potentials for manipulating leaf senescence in crops. Finally, it is speculated that technologies based on the molecular understanding of nutrient recycling during leaf senescence are highly desirable and are expected to be developed in future translational leaf senescence research. © The Author 2014. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Titan Lifting Entry & Atmospheric Flight (T-LEAF) Science Mission

Science.gov (United States)

Lee, G.; Sen, B.; Ross, F.; Sokol, D.

2016-12-01

Northrop Grumman has been developing the Titan Lifting Entry & Atmospheric Flight (T-LEAF) sky rover to roam the lower atmosphere and observe at close quarters the lakes and plains of Saturn's ocean moon, Titan. T-LEAF also supports surface exploration and science by providing precision delivery of in-situ instruments to the surface of Titan. T-LEAF is a highly maneuverable sky rover and its aerodynamic shape (i.e., a flying wing) does not restrict it to following prevailing wind patterns on Titan, but allows mission operators to chart its course. This freedom of mobility allows T-LEAF to follow the shorelines of Titan's methane lakes, for example, or to target very specific surface locations. We will present a straw man concept of T-LEAF, including size, mass, power, on-board science payloads and measurement, and surface science dropsonde deployment CONOPS. We will discuss the various science instruments and their vehicle level impacts, such as meteorological and electric field sensors, acoustic sensors for measuring shallow depths, multi-spectral imagers, high definition cameras and surface science dropsondes. The stability of T-LEAF and its long residence time on Titan will provide for time to perform a large aerial survey of select prime surface targets deployment of dropsondes at selected locations surface measurements that are coordinated with on-board remote measurements communication relay capabilities to orbiter (or Earth). In this context, we will specifically focus upon key factors impacting the design and performance of T-LEAF science: science payload accommodation, constraints and opportunities characteristics of flight, payload deployment and measurement CONOPS in the Titan atmosphere. This presentation will show how these factors provide constraints as well as enable opportunities for novel long duration scientific studies of Titan's surface.

Butterfly Learning and the Diversification of Plant Leaf Shape

Directory of Open Access Journals (Sweden)

Denise Dalbosco Dell'aglio

2016-07-01

Full Text Available Visual cues are important for insects to find flowers and host plants. It has been proposed that the diversity of leaf shape in Passiflora vines could be a result of negative frequency dependent selection driven by visual searching behavior among their butterfly herbivores. Here we tested the hypothesis that Heliconius butterflies use leaf shape as a cue to initiate approach towards a host plant. We first tested for the ability to recognize shapes using a food reward conditioning experiment. Butterflies showed an innate preference for flowers with three and five petals. However, they could be trained to increase the frequency of visits to a non-preferred flower with two petals, indicating an ability to learn to associate shape with a reward. Next we investigated shape learning specifically in the context of oviposition by conditioning females to lay eggs on two shoots associated with different artificial leaf shapes: their own host plant, Passiflora biflora, and a lanceolate non-biflora leaf shape. The conditioning treatment had a significant effect on the approach of butterflies to the two leaf shapes, consistent with a role for shape learning in oviposition behavior. This study is the first to show that Heliconius butterflies use shape as a cue for feeding and oviposition, and can learn shape preference for both flowers and leaves. This demonstrates the potential for Heliconius to drive negative frequency dependent selection on the leaf shape of their Passiflora host plants.

Production of α-amylase from Streptomyces sp. SLBA-08 strain using agro-industrial by-products

Directory of Open Access Journals (Sweden)

Édilla Ribeiro dos Santos

2012-10-01

Full Text Available Approximately 1.5 trillion tons are the estimated yearly biomass production, making it an essentially unlimited source of raw material for environmentally friendly and biocompatible products transformed by microorganism, specially fungi and actinomycetes. Several lignocellulosic residues, such as sisal waste and sugarcane bagasse contain starch in their structures which could become important sources for the production of amylases. This study evaluated the production of amylolytic enzymes using Streptomyces sp. SLBA-08 strain, isolated from a semi-arid soil, according to their ability to grow on soluble starch as the sole carbon source. The effect of the carbon source (sisal waste and sugarcane bagasse on α-amylase production was studied using submerged cultivations at 30 ºC. The highest level of α-amylase activity corresponded to 10.1 U. mL-1 and was obtained using sisal waste (2.7% and urea (0.8% in submerged fermentation after 3 days of cultivation. The partial characterization showed the best α-amylase activity at 50ºC and pH 7.0. These results are of great importance for the use of sisal waste as a substrate for biotechnological proposes.

Gamma irradiation enhances biological activities of mulberry leaf extract

International Nuclear Information System (INIS)

Cho, Byoung-Ok; Che, Denis Nchang; Yin, Hong-Hua; Jang, Seon-Il

2017-01-01

The purpose of this study was to investigate the influence of irradiation on the anti-oxidative, anti-inflammatory and whitening effects of mulberry leaf extract. This was done by comparing the phenolic contents; 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging effects; 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulphonicacid) (ABTS) radical scavenging effects; in vitro tyrosinase inhibitory effects and the production of IL-6, TNF-α, PGE 2 , and NO in lipopolysaccharide-stimulated RAW264.7 macrophages and the production of IL-6 and TNF-α in phorbol 12-myristate 13-acetate plus calcium ionophore A23187-stimulated HMC-1 cells, respectively. The results showed that irradiated mulberry leaf extract possesses more anti-oxidant, anti-inflammatory, and tyrosinase inhibitory activities than their non-irradiated counterpart, probably due to increase in phenolic contents induced by gamma irradiation at dose of 10kGy. This research stresses on the importance of irradiation in functional foods. - Highlights: • Gamma-irradiated mulberry leaf extract enhanced in vitro antioxidant activities. • Gamma-irradiated mulberry leaf extract enhanced in vitro tyrosinase inhibitory effects. • Gamma-irradiated mulberry leaf extract treatment reduced the production of IL-6, TNF-α, PGE 2 , and NO.

Ecophysiological function of leaf 'windows' in Lithops species - 'Living Stones' that grow underground.

Science.gov (United States)

Martin, C E; Brandmeyer, E A; Ross, R D

2013-01-01

Leaf temperatures were lower when light entry at the leaf tip window was prevented through covering the window with reflective tape, relative to leaf temperatures of plants with leaf tip windows covered with transparent tape. This was true when leaf temperatures were measured with an infrared thermometer, but not with a fine-wire thermocouple. Leaf tip windows of Lithops growing in high-rainfall regions of southern Africa were larger than the windows of plants (numerous individuals of 17 species) growing in areas with less rainfall and, thus, more annual insolation. The results of this study indicate that leaf tip windows of desert plants with an underground growth habit can allow entry of supra-optimal levels of radiant energy, thus most likely inhibiting photosynthetic activity. Consequently, the size of the leaf tip windows correlates inversely with habitat solar irradiance, minimising the probability of photoinhibition, while maximising the absorption of irradiance in cloudy, high-rainfall regions. © 2012 German Botanical Society and The Royal Botanical Society of the Netherlands.

Comparison of gold leaf thickness in Namban folding screens using X-ray fluorescence

Energy Technology Data Exchange (ETDEWEB)

Pessanha, Sofia; Madeira, Teresa I.; Manso, Marta [Centro de Fisica Atomica da Universidade de Lisboa, Lisbon (Portugal); Guerra, Mauro; Carvalho, Maria Luisa [Centro de Fisica Atomica da Universidade de Lisboa, Lisbon (Portugal); Universidade Nova de Lisboa, Departamento de Fisica, Faculdade de Ciencias e Tecnologia, Caparica (Portugal); Gac, Agnes le [Centro de Fisica Atomica da Universidade de Lisboa, Lisbon (Portugal); Universidade Nova de Lisboa, Departamento de Conservacao e Restauro, Faculdade de Ciencias e Tecnologia, Caparica (Portugal)

2014-09-15

In this work, the thickness of the gold leaf applied in six Japanese folding screens is compared using a nondestructive approach. Four screens belonging to the Momoyama period (∝1573-1603) and two screens belonging to the early Edo period (∝1603-1868) were analyzed in situ using energy dispersive X-ray fluorescence, and the thickness of the applied gold leaf was evaluated using a methodology based on the attenuation of the different characteristic lines of gold in the gold leaf layer. Considering that the leaf may well not be made of pure gold, we established that, for the purpose of comparing the intensity ratios of the Au lines, layers made with gold leaf of high grade can be considered identical. The gold leaf applied in one of the screens from the Edo period was found to be thinner than the gold leaf applied in the other ones. This is consistent with the development of the beating technology to obtain ever more thin gold leafs. (orig.)

Comparison of gold leaf thickness in Namban folding screens using X-ray fluorescence

International Nuclear Information System (INIS)

Pessanha, Sofia; Madeira, Teresa I.; Manso, Marta; Guerra, Mauro; Carvalho, Maria Luisa; Gac, Agnes le

2014-01-01

In this work, the thickness of the gold leaf applied in six Japanese folding screens is compared using a nondestructive approach. Four screens belonging to the Momoyama period (∝1573-1603) and two screens belonging to the early Edo period (∝1603-1868) were analyzed in situ using energy dispersive X-ray fluorescence, and the thickness of the applied gold leaf was evaluated using a methodology based on the attenuation of the different characteristic lines of gold in the gold leaf layer. Considering that the leaf may well not be made of pure gold, we established that, for the purpose of comparing the intensity ratios of the Au lines, layers made with gold leaf of high grade can be considered identical. The gold leaf applied in one of the screens from the Edo period was found to be thinner than the gold leaf applied in the other ones. This is consistent with the development of the beating technology to obtain ever more thin gold leafs. (orig.)

Gold leaf counter electrodes for dye-sensitized solar cells

Science.gov (United States)

Shimada, Kazuhiro; Toyoda, Takeshi

2018-03-01

In this study, a gold leaf 100 nm thin film is used as the counter electrode in dye-sensitized solar cells. The traditional method of hammering gold foil to obtain a thin gold leaf, which requires only small amounts of gold, was employed. The gold leaf was then attached to the substrate using an adhesive to produce the gold electrode. The proposed approach for fabricating counter electrodes is demonstrated to be facile and cost-effective, as opposed to existing techniques. Compared with electrodes prepared with gold foil and sputtered gold, the gold leaf counter electrode demonstrates higher catalytic activity with a cobalt-complex electrolyte and higher cell efficiency. The origin of the improved performance was investigated by surface morphology examination (scanning electron microscopy), various electrochemical analyses (cyclic voltammetry, linear sweep voltammetry, and electrochemical impedance spectroscopy), and crystalline analysis (X-ray diffractometry).

Novel fungal disease in complex leaf-cutting ant societies

DEFF Research Database (Denmark)

Hughes, David Peter; Evans, Harry C.; Hywel-Jones, Nigel

2009-01-01

1. The leaf-cutting ants practise an advanced system of mycophagy where they grow a fungus as a food source. As a consequence of parasite threats to their crops, they have evolved a system of morphological, behavioural, and chemical defences, particularly against fungal pathogens (mycopathogens). 2....... Specific fungal diseases of the leaf-cutting ants themselves have not been described, possibly because broad spectrum anti-fungal defences against mycopathogens have reduced their susceptibility to entomopathogens. 3. Using morphological and molecular tools, the present study documents three rare infection...... events of Acromyrmex and Atta leaf-cutting ants by Ophiocordyceps fungi, agenus of entomopathogens that is normally highly specific in its host choice. 4. As leaf-cutting ants have been intensively studied, the absence of prior records of Ophiocordyceps suggests that these infections may be a novel event...

Radioprotection of Swiss albino mice by Adhatoda vesica leaf extract

International Nuclear Information System (INIS)

Kumar, A.

2003-01-01

Full text: The radioprotective role of aqueous extract of Adhatoda vesica leaf extract against radiation induced hematological alterations in peripheral blood of Swiss albino mice was studied at various post-irradiation intervals between 6 hrs to 30 days. Oral administration of Adhatoda vesica leaf extract (800 mg / kg body weight) prior to whole-body irradiation showed a significant protection in terms of survival percentage and hematological parameters. Mice exposed to radiation (8 Gy) without Adhatoda vesica leaf extract pre-treatment exhibited signs of radiation sickness like anorexia, lethargicity, ruffled hairs and diarrhoea and such animals died within 26 days post-irradiation. The dose reduction factor (DRF=1.6) for Adhatoda vesica leaf extract was calculated from LD50/30 values. A significant decline in hematological constituents (RBCs, WBCs, Hb and Hct) was evident till day 15, at later period of observation (day 15 onwards), no animals could survive from control group whereas, in Adhatoda vesica leaf extract pre-treated irradiated group, a gradual recovery was noted in the hematological values. However, these hematological values remained significantly below the normal even till day 30. A significant decrease in GSH was recorded in control animals. Experimental animals showed a significant increase in GSH content (blood as well as liver) with respect to control, but such values remained below normal. A significant increase in TBARS level in liver and serum was evident in control animals. Although, no significant difference was noticed in such levels in normal and Adhatoda vesica leaf extract treated animals. But, a significant decrease was registered in Adhatoda vesica leaf extract pretreated irradiated animals. The results from the present study suggest that Adhatoda vesica leaf extract has radioprotective role in stimulating/protecting the hematopoietic system thereby enhancing the survival and increasing the hematological constituents in peripheral

Leaf and stem morphoanatomy of Petiveria alliacea.

Science.gov (United States)

Duarte, M R; Lopes, J F

2005-12-01

Petiveria alliacea is a perennial herb native to the Amazonian region and used in traditional medicine for different purposes, such as diuretic, antispasmodic and anti-inflammatory. The morphoanatomical characterization of the leaf and stem was carried out, in order to contribute to the medicinal plant identification. The plant material was fixed, freehand sectioned and stained either with toluidine blue or astra blue and basic fuchsine. Microchemical tests were also applied. The leaf is simple, alternate and elliptic. The blade exhibits paracytic stomata on the abaxial side, non-glandular trichomes and dorsiventral mesophyll. The midrib is biconvex and the petiole is plain-convex, both traversed by collateral vascular bundles adjoined with sclerenchymatic caps. The stem, in incipient secondary growth, presents epidermis, angular collenchyma, starch sheath and collateral vascular organization. Several prisms of calcium oxalate are seen in the leaf and stem.

Leaf morphophysiology of a Neotropical mistletoe is shaped by seasonal patterns of host leaf phenology.

Science.gov (United States)

Scalon, Marina Corrêa; Rossatto, Davi Rodrigo; Domingos, Fabricius Maia Chaves Bicalho; Franco, Augusto Cesar

2016-04-01

Several mistletoe species are able to grow and reproduce on both deciduous and evergreen hosts, suggesting a degree of plasticity in their ability to cope with differences in intrinsic host functions. The aim of this study was to investigate the influence of host phenology on mistletoe water relations and leaf gas exchange. Mistletoe Passovia ovata parasitizing evergreen (Miconia albicans) hosts and P. ovata parasitizing deciduous (Byrsonima verbascifolia) hosts were sampled in a Neotropical savanna. Photosynthetic parameters, diurnal cycles of stomatal conductance, pre-dawn and midday leaf water potential, and stomatal anatomical traits were measured during the peak of the dry and wet seasons, respectively. P. ovata showed distinct water-use strategies that were dependent on host phenology. For P. ovata parasitizing the deciduous host, water use efficiency (WUE; ratio of photosynthetic rate to transpirational water loss) was 2-fold lower in the dry season than in the wet season; in contrast, WUE was maintained at the same level during the wet and dry seasons in P. ovata parasitizing the evergreen host. Generally, mistletoe and host diurnal cycles of stomatal conductance were linked, although there were clear differences in leaf water potential, with mistletoe showing anisohydric behaviour and the host showing isohydric behaviour. Compared to mistletoes attached to evergreen hosts, those parasitizing deciduous hosts had a 1.4-fold lower stomatal density and 1.2-fold wider stomata on both leaf surfaces, suggesting that the latter suffered less intense drought stress. This is the first study to show morphophysiological differences in the same mistletoe species parasitizing hosts of different phenological groups. Our results provide evidence that phenotypical plasticity (anatomical and physiological) might be essential to favour the use of a greater range of hosts.

7 CFR 29.2438 - Thin Leaf (C Group).

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Thin Leaf (C Group). 29.2438 Section 29.2438... REGULATIONS TOBACCO INSPECTION Standards Grades § 29.2438 Thin Leaf (C Group). This group consists of leaves... body than those of the B group, and show little or no ground injury. Choice- and fine-quality tobacco...

7 CFR 29.1163 - Smoking Leaf (H Group).

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Smoking Leaf (H Group). 29.1163 Section 29.1163... REGULATIONS TOBACCO INSPECTION Standards Grades § 29.1163 Smoking Leaf (H Group). This group consists of leaves normally grown at or above the midportion of the stalk. Leaves of the H group show a high degree...

Determining past leaf-out times of New England's deciduous forests from herbarium specimens.

Science.gov (United States)

Everill, Peter H; Primack, Richard B; Ellwood, Elizabeth R; Melaas, Eli K

2014-08-01

• There is great interest in studying leaf-out times of temperate forests because of the importance of leaf-out in controlling ecosystem processes, especially in the face of a changing climate. Remote sensing and modeling, combined with weather records and field observations, are increasing our knowledge of factors affecting variation in leaf-out times. Herbarium specimens represent a potential new source of information to determine whether the variation in leaf-out times observed in recent decades is comparable to longer time frames over past centuries.• Here we introduce the use of herbarium specimens as a method for studying long-term changes in leaf-out times of deciduous trees. We collected historical leaf-out data for the years 1834-2008 from common deciduous trees in New England using 1599 dated herbarium specimens with young leaves.• We found that leaf-out dates are strongly affected by spring temperature, with trees leafing out 2.70 d earlier for each degree C increase in mean April temperature. For each degree C increase in local temperature, trees leafed out 2.06 d earlier. Additionally, the mean response of leaf-out dates across all species and sites over time was 0.4 d earlier per decade. Our results are of comparable magnitude to results from studies using remote sensing and direct field observations.• Across New England, mean leaf-out dates varied geographically in close correspondence with those observed in studies using satellite data. This study demonstrates that herbarium specimens can be a valuable source of data on past leaf-out times of deciduous trees. © 2014 Botanical Society of America, Inc.

A sensitive hydrogen peroxide sensor based on leaf-like silver

International Nuclear Information System (INIS)

Meng, Zuchao; Zhang, Mingyin; Zhang, Hongfang; Zheng, Jianbin

2014-01-01

A novel non-enzymatic hydrogen peroxide sensor based on leaf-like silver was constructed. The leaf-like silver was synthesized on the surface of L-cysteine (L-cys) by electrodeposition. Scanning electron microscopy and electrochemical techniques were used to characterize the leaf-like silver nanoparticles. The sensor showed high electrocatalytic activity towards the reduction of hydrogen peroxide. A wide linear range of 2.5–1.5 mM with a low detection limit of 0.7 µM was obtained. Excellent electrocatalytic activity, large surface-to-volume ratio and efficient electron transport properties of leaf-like silver have enabled stable and highly sensitive performance for the non-enzymatic hydrogen peroxide sensor. (paper)

Mycorrhizal Stimulation of Leaf Gas Exchange in Relation to Root Colonization, Shoot Size, Leaf Phosphorus and Nitrogen: A Quantitative Analysis of the Literature Using Meta-Regression.

Science.gov (United States)

Augé, Robert M; Toler, Heather D; Saxton, Arnold M

2016-01-01

Arbuscular mycorrhizal (AM) symbiosis often stimulates gas exchange rates of the host plant. This may relate to mycorrhizal effects on host nutrition and growth rate, or the influence may occur independently of these. Using meta-regression, we tested the strength of the relationship between AM-induced increases in gas exchange, and AM size and leaf mineral effects across the literature. With only a few exceptions, AM stimulation of carbon exchange rate (CER), stomatal conductance (g s), and transpiration rate (E) has been significantly associated with mycorrhizal stimulation of shoot dry weight, leaf phosphorus, leaf nitrogen:phosphorus ratio, and percent root colonization. The sizeable mycorrhizal stimulation of CER, by 49% over all studies, has been about twice as large as the mycorrhizal stimulation of g s and E (28 and 26%, respectively). CER has been over twice as sensitive as g s and four times as sensitive as E to mycorrhizal colonization rates. The AM-induced stimulation of CER increased by 19% with each AM-induced doubling of shoot size; the AM effect was about half as large for g s and E. The ratio of leaf N to leaf P has been more closely associated with mycorrhizal influence on leaf gas exchange than leaf P alone. The mycorrhizal influence on CER has declined markedly over the 35 years of published investigations.

Mycorrhizal stimulation of leaf gas exchange in relation to root colonization, shoot size, leaf phosphorus and nitrogen: a quantitative analysis of the literature using meta-regression

Directory of Open Access Journals (Sweden)

Robert M. Augé

2016-07-01

Full Text Available Arbuscular mycorrhizal (AM symbiosis often stimulates gas exchange rates of the host plant. This may relate to mycorrhizal effects on host nutrition and growth rate, or the influence may occur independently of these. Using meta-regression, we tested the strength of the relationship between AM-induced increases in gas exchange, and AM size and leaf mineral effects across the literature. With only a few exceptions, AM stimulation of carbon exchange rate (CER, stomatal conductance (gs and transpiration rate (E has been significantly associated with mycorrhizal stimulation of shoot dry weight, leaf phosphorus, leaf nitrogen: phosphorus ratio and percent root colonization. The sizeable mycorrhizal stimulation of CER, by 49% over all studies, has been about twice as large as the mycorrhizal stimulation of gs and E (28% and 26%, respectively. Carbon exchange rate has been over twice as sensitive as gs and four times as sensitive as E to mycorrhizal colonization rates. The AM-induced stimulation of CER increased by 19% with each AM-induced doubling of shoot size; the AM effect was about half as large for gs and E. The ratio of leaf N to leaf P has been more closely associated with mycorrhizal influence on leaf gas exchange than leaf P alone. The mycorrhizal influence on CER has declined markedly over the 35 years of published investigations.

Surf Zone Sediment Size Variation, Morphodynamics, and Hydrodynamics During Sea/Land Breeze and El-Norte Storm in Sisal, Yucatan, Mexico

Science.gov (United States)

Alrushaid, T.; Figlus, J.; Torres-Freyermuth, A.; Puleo, J. A.; Dellapenna, T. M.

2016-02-01

Coastlines around the world are under ever-increasing pressure due to population trends, commerce, and geophysical processes like tropical storms and erosion. This multi-institutional field campaign was conducted to improve our understanding of complex nearshore processes under varying forcing conditions on a microtidal, sandy beach located in Sisal, Yucatan from 3/27 to 4/12/2014. Hydrodynamics, morphodynamics, and textural variability were investigated during: (1) a cold front event (referred to as El-Norte); (2) land breeze (LB); and (3) sea breeze (SB). The instrumentation layout included three surf/swash zone cross-shore transects where water elevation, suspended sediment concentration, bed load, and current velocities were measured, as well as several offshore ADCP for hydrodynamic measurements. TKE, τb, ɛ and were estimated using the data obtained from surf zone ADV. In addition, Hs and Tsin the surf zone were computed using measurements from ADV pressure sensors, while a separate pressure transducer was used to obtain water free-surface elevation within the swash zone. During SB cycles the study area experienced wind velocities reaching up to 12ms-1, and 15ms-1 during El-Norte. Elevated wind stress during El-Norte resulted in Hs of 1.5m and 0.6m in water depths of 10m and 0.4m, respectively. Surface sediment grab samples during SB/LB cycles showed that the swash zone had a moderately well sorted distribution with a mean grain size of 0.5mm, while poor sorting and a mean grain size of 0.7mm were found during El-Norte. Additionally, measured bathymetry data showed evidence for offshore sandbar migration during strong offshore currents (0.4ms-1) during El-Norte, while onshore sandbar migration was evident during SB/LB periods (0.3ms-1 and 0.1ms-1, respectively). This study highlights how different weather forcing conditions affect hydrodynamics, morphodynamics, and textural variability on a sandy beach. Aside from furthering our knowledge on these complex

Impact of Vertical Canopy Position on Leaf Spectral Properties and Traits across Multiple Species

Directory of Open Access Journals (Sweden)

Tawanda W. Gara

2018-02-01

Full Text Available Understanding the vertical pattern of leaf traits across plant canopies provide critical information on plant physiology, ecosystem functioning and structure and vegetation response to climate change. However, the impact of vertical canopy position on leaf spectral properties and subsequently leaf traits across the entire spectrum for multiple species is poorly understood. In this study, we examined the ability of leaf optical properties to track variability in leaf traits across the vertical canopy profile using Partial Least Square Discriminatory Analysis (PLS-DA. Leaf spectral measurements together with leaf traits (nitrogen, carbon, chlorophyll, equivalent water thickness and specific leaf area were studied at three vertical canopy positions along the plant stem: lower, middle and upper. We observed that foliar nitrogen (N, chlorophyll (Cab, carbon (C, and equivalent water thickness (EWT were higher in the upper canopy leaves compared with lower shaded leaves, while specific leaf area (SLA increased from upper to lower canopy leaves. We found that leaf spectral reflectance significantly (P ≤ 0.05 shifted to longer wavelengths in the ‘red edge’ spectrum (685–701 nm in the order of lower > middle > upper for the pooled dataset. We report that spectral bands that are influential in the discrimination of leaf samples into the three groups of canopy position, based on the PLS-DA variable importance projection (VIP score, match with wavelength regions of foliar traits observed to vary across the canopy vertical profile. This observation demonstrated that both leaf traits and leaf reflectance co-vary across the vertical canopy profile in multiple species. We conclude that canopy vertical position has a significant impact on leaf spectral properties of an individual plant’s traits, and this finding holds for multiple species. These findings have important implications on field sampling protocols, upscaling leaf traits to canopy level

7 CFR 29.2437 - Heavy Leaf (B Group).

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Heavy Leaf (B Group). 29.2437 Section 29.2437... REGULATIONS TOBACCO INSPECTION Standards Grades § 29.2437 Heavy Leaf (B Group). This group consists of leaves..., are heavier in body than those of the X or C groups, and show no ground injury. Choice- and fine...

The global distribution of leaf chlorophyll content and seasonal controls on carbon uptake

Science.gov (United States)

Croft, H.; Chen, J. M.; Luo, X.; Bartlett, P. A.; Staebler, R. M.; He, L.; Mo, G.; Luo, S.; Simic, A.; Arabian, J.; He, Y.; Zhang, Y.; Beringer, J.; Hutley, L. B.; Noland, T. L.; Arellano, P.; Stahl, C.; Homolová, L.; Bonal, D.; Malenovský, Z.; Yi, Q.; Amiri, R.

2017-12-01

Leaf chlorophyll (ChlLeaf) is crucial to biosphere-atmosphere exchanges of carbon and water, and the functioning of terrestrial ecosystems. Improving the accuracy of modelled photosynthetic carbon uptake is a central priority for understanding ecosystem response to a changing climate. A source of uncertainty within gross primary productivity (GPP) estimates is the failure to explicitly consider seasonal controls on leaf photosynthetic potential. Whilst the inclusion of ChlLeafinto carbon models has shown potential to provide a physiological constraint, progress has been hampered by the absence of a spatially-gridded, global chlorophyll product. Here, we present the first spatially-continuous, global view of terrestrial ChlLeaf, at weekly intervals. Satellite-derived ChlLeaf was modelled using a physically-based radiative transfer modelling approach, with a two stage model inversion method. 4-Scale and SAIL canopy models were first used to model leaf-level reflectance from ENIVSAT MERIS 300m satellite data. The PROSPECT leaf model was then used to derive ChlLeaf from the modelled leaf reflectance. This algorithm was validated using measured ChlLeaf data from 248 measurements within 26 field locations, covering six plant functional types (PFTs). Modelled results show very good relationships with measured data, particularly for deciduous broadleaf forests (R2 = 0.67; pmake an important step towards improving the accuracy of global carbon budgets.

Leaf shape responds to temperature but not CO2 in Acer rubrum.

Science.gov (United States)

Royer, Dana L

2012-01-01

The degree of leaf dissection and the presence of leaf teeth, along with tooth size and abundance, inversely correlate with mean annual temperature (MAT) across many plant communities. These relationships form the core of several methods for reconstructing MAT from fossils, yet the direct selection of temperature on tooth morphology has not been demonstrated experimentally. It is also not known if atmospheric CO(2) concentration affects leaf shape, limiting confidence in ancient climate reconstructions because CO(2) has varied widely on geologic timescales. Here I report the results of growing Acer rubrum (red maple) in growth cabinets at contrasting temperature and CO(2) conditions. The CO(2) treatment imparted no significant differences in leaf size and shape, while plants grown at cooler temperatures tended to have more teeth and more highly dissected leaves. These results provide direct evidence for the selection of temperature on leaf shape in one species, and support a key link in many leaf-climate methods. More broadly, these results increase confidence for using leaf shape in fossils to reconstruct paleoclimate.

Leaf Dynamics of Panicum maximum under Future Climatic Changes.

Science.gov (United States)

Britto de Assis Prado, Carlos Henrique; Haik Guedes de Camargo-Bortolin, Lívia; Castro, Érique; Martinez, Carlos Alberto

2016-01-01

Panicum maximum Jacq. 'Mombaça' (C4) was grown in field conditions with sufficient water and nutrients to examine the effects of warming and elevated CO2 concentrations during the winter. Plants were exposed to either the ambient temperature and regular atmospheric CO2 (Control); elevated CO2 (600 ppm, eC); canopy warming (+2°C above regular canopy temperature, eT); or elevated CO2 and canopy warming (eC+eT). The temperatures and CO2 in the field were controlled by temperature free-air controlled enhancement (T-FACE) and mini free-air CO2 enrichment (miniFACE) facilities. The most green, expanding, and expanded leaves and the highest leaf appearance rate (LAR, leaves day(-1)) and leaf elongation rate (LER, cm day(-1)) were observed under eT. Leaf area and leaf biomass were higher in the eT and eC+eT treatments. The higher LER and LAR without significant differences in the number of senescent leaves could explain why tillers had higher foliage area and leaf biomass in the eT treatment. The eC treatment had the lowest LER and the fewest expanded and green leaves, similar to Control. The inhibitory effect of eC on foliage development in winter was indicated by the fewer green, expanded, and expanding leaves under eC+eT than eT. The stimulatory and inhibitory effects of the eT and eC treatments, respectively, on foliage raised and lowered, respectively, the foliar nitrogen concentration. The inhibition of foliage by eC was confirmed by the eC treatment having the lowest leaf/stem biomass ratio and by the change in leaf biomass-area relationships from linear or exponential growth to rectangular hyperbolic growth under eC. Besides, eC+eT had a synergist effect, speeding up leaf maturation. Therefore, with sufficient water and nutrients in winter, the inhibitory effect of elevated CO2 on foliage could be partially offset by elevated temperatures and relatively high P. maximum foliage production could be achieved under future climatic change.

Variation in essential oil composition within individual leaves of sweet basil (Ocimum basilicum L.) is more affected by leaf position than by leaf age.

Science.gov (United States)

Fischer, Ravit; Nitzan, Nadav; Chaimovitsh, David; Rubin, Baruch; Dudai, Nativ

2011-05-11

The aroma in sweet basil is a factor affecting the commercial value of the crop. In previous studies leaf age was considered to be a factor that influences the composition of essential oil (EO). In this study it was hypothesized that a single observation of the EO content in leaves from different positions on the main stem (young vs old) could predict the developmental changes in the plant during its life cycle. Plants harvested at week 16 demonstrated an exponential increase (R(2) = 0.92) in EO concentration in leaves on the main stem and lateral shoots, indicating higher EO concentrations in younger than in older leaves. Eugenol and methyleugenol predominated (28-77%) in the extract. Eugenol levels were higher in younger leaves (∼53%), and methyl-eugenol levels predominated in older leaves (∼68%). Linalool was lower in mature leaves than in younger leaves. This suggested that eugenol converted into methyleugenol and linalool decreased as leaf mature. However, in weekly monitored plants, the levels of these compounds in the EO had limited variation in the maturing leaf regardless of its position on the stem. This proposed that the EO composition in an individual leaf is mostly affected by the leaf position on the stem and not by its maturation process. Because leaf position is related to plant development, it is probable that the plant's physiological age at the time of leaf formation from the primordial tissue is the factor affecting the EO composition. It was concluded that interpretation of scientific observations should be carried out with caution and that hypotheses should be tested utilizing multifaceted approaches.

Leaf reflectance-nitrogen-chlorophyll relations among three south Texas woody rangeland plant species

Science.gov (United States)

Gausman, H. W.; Everitt, J. H.; Escobar, D. E. (Principal Investigator)

1982-01-01

Annual variations in the nitrogen-chlorophyll leaf reflectance of hackberry, honey mesquite and live oak in south Texas, were compared. In spring, leaf reflectance at the 0.55 m wavelength and nitrogen (N) concentration was high but leaf chlorophyll (chl) concentrations were low. In summer, leaf reflectance and N-concentration were low but lead chl concentrations were high. Linear correlations for both spring and summer of leaf reflectance with N and chl concentration or deviations from linear regression were not statistically significant.

Leaf mineral nutrient remobilization during leaf senescence and modulation by nutrient deficiency.

Directory of Open Access Journals (Sweden)

Anne eMaillard

2015-05-01

Full Text Available Higher plants have to cope with fluctuating mineral resource availability. However strategies such as stimulation of root growth, increased transporter activities, and nutrient storage and remobilization have been mostly studied for only a few macronutrients. Leaves of cultivated crops (Zea mays, Brassica napus, Pisum sativum, Triticum aestivum, Hordeum vulgare and tree species (Quercus robur, Populus nigra, Alnus glutinosa grown under field conditions were harvested regularly during their life span and analysed to evaluate the net mobilization of 13 nutrients during leaf senescence. While N was remobilized in all plant species with different efficiencies ranging from 40% (maize to 90% (wheat, other macronutrients (K-P-S-Mg were mobilized in most species. Ca and Mn, usually considered as having low phloem mobility were remobilized from leaves in wheat and barley. Leaf content of Cu-Mo-Ni-B-Fe-Zn decreased in some species, as a result of remobilization. Overall, wheat, barley and oak appeared to be the most efficient at remobilization while poplar and maize were the least efficient. Further experiments were performed with rapeseed plants subjected to individual nutrient deficiencies. Compared to field conditions, remobilization from leaves was similar (N-S-Cu or increased by nutrient deficiency (K-P-Mg while nutrient deficiency had no effect on Mo-Zn-B-Ca-Mn, which seemed to be non-mobile during leaf senescence under field conditions. However, Ca and Mn were largely mobilized from roots (-97 and -86% of their initial root contents, respectively to shoots. Differences in remobilization between species and between nutrients are then discussed in relation to a range of putative mechanisms.

Biophysical constraints on leaf expansion in a tall conifer.

Science.gov (United States)

Fredrick C. Meinzer; Barbara J. Bond; Jennifer A. Karanian

2008-01-01

The physiological mechanisms responsible for reduced extension growth as trees increase in height remain elusive. We evaluated biophysical constraints on leaf expansion in old-growth Douglas-fir (Psuedotsuga menziesii (Mirb.) Franco) trees. Needle elongation rates, plastic and elastic extensibility, bulk leaf water, (L...

Transformation of Leaf-like Zinc Dendrite in Oxidation and Reduction Cycle

International Nuclear Information System (INIS)

Nakata, Akiyoshi; Murayama, Haruno; Fukuda, Katsutoshi; Yamane, Tomokazu; Arai, Hajime; Hirai, Toshiro; Uchimoto, Yoshiharu; Yamaki, Jun-ichi; Ogumi, Zempachi

2015-01-01

Highlights: • Leaf-like zinc dendrites change to leaf-like residual oxides at high oxidation current density (10 mA cm −2 ) whereas it completely dissolves at low oxidation current density (1 mA cm −2 ). • Leaf-like residual oxide products is transformed to zinc deposits with particulate morphology, resulting in good rechargeability. • The residual zinc oxide provides sufficient zincate on its reduction, preventing the diffusion-limited condition that causes leaf-like dendrite formation. - Abstract: Zinc is a promising negative electrode material for aqueous battery systems whereas it shows insufficient rechargeability for use in secondary batteries. It has been reported that leaf-like dendrite deposits are often the origin of cell-failure, however, their nature and behavior on discharge (oxidation) - charge (reduction) cycling have been only poorly understood. Here we investigate the transformation of the leaf-like zinc dendrites using ex-situ scanning electron microscopy, X-ray computational tomography and in-situ X-ray diffraction. It is shown that the leaf-like zinc dendrites obtained under diffusion-limited conditions are nearly completely dissolved at a low oxidation current density of 1 mA cm −2 and cause re-evolution of the zinc dendrites. Oxidation at a high current density of 10 mA cm −2 leads to the formation of leaf-like zinc oxide residual products that result in particulate zinc deposits in the following reduction process, enabling good rechargeability. The reaction behavior of this oxide residue is detailed and discussed for the development of long-life zinc electrodes

Does oolong tea (Camellia sinensis) made from a combination of leaf and stem smell more aromatic than leaf-only tea? Contribution of the stem to oolong tea aroma.

Science.gov (United States)

Zeng, Lanting; Zhou, Ying; Fu, Xiumin; Mei, Xin; Cheng, Sihua; Gui, Jiadong; Dong, Fang; Tang, Jinchi; Ma, Shengzhou; Yang, Ziyin

2017-12-15

The raw materials used to make oolong tea (Camellia sinensis) are a combination of leaf and stem. Oolong tea made from leaf and stem is thought to have a more aromatic smell than leaf-only tea. However, there is no available evidence to support the viewpoint. In this study, sensory evaluation and detailed characterization of emitted and internal volatiles (not readily emitted, but stored in samples) of dry oolong teas and infusions indicated that the presence of stem did not significantly improve the total aroma characteristics. During the enzyme-active processes, volatile monoterpenes and theanine were accumulated more abundantly in stem than in leaf, while jasmine lactone, indole, and trans-nerolidol were lower in stem than in leaf. Tissue-specific aroma-related gene expression and availability of precursors of aroma compounds resulted in different aroma distributions in leaf and stem. This study presents the first determination of the contribution of stem to oolong tea aroma. Copyright © 2017 Elsevier Ltd. All rights reserved.

Induced leaf variations in faba bean

International Nuclear Information System (INIS)

Yasin, M.

1996-01-01

The frequency and spectrum of M2 chlorophyll and other leaf mutations after gamma ray, ethyl methane sulfonate (EMS) and nitrous oxide (N2O) seed treatment in two varieties of faba bean were studied. In general, cv JV1 was more sensitive and EMS treatment was most effective. The frequency of chlorina-type mutations was higher than that of xantha and chlorotica type chlorophyll mutations. The highest frequency of variations was observed in leaflet texture, followed by arrangement, shape and size in both varieties. The use of these leaf mutations in formulating an ideotype of Vicia faba L. are discussed

Leaf nutrient resorption, leaf lifespan and the retention of nutrients in seagrass systems

NARCIS (Netherlands)

Hemminga, M.A.; Marbà, N.; Stapel, J.

1999-01-01

Efficient nutrient resorption from senescing leaves, and extended leaf life spans are important strategies in order to conserve nutrients for plants in general. Despite the fact that seagrasses often grow in oligotrophic waters, these conservation strategies are not strongly developed in seagrasses.

Ozone and sulphur dioxide effects on leaf water potential of Petunia

Energy Technology Data Exchange (ETDEWEB)

Elkiey, T.; Ormrod, D.P.

1979-01-01

Three cultivars of Petunia hydrida Vilm., of differing ozone visible injury sensitivity, were exposed to 40 parts per hundred million (pphm) ozone and/or 80 pphm SO/sub 2/ for 4 h to study the relationships of leaf water potential, pollutant exposure, and cultivar sensitivity. Ozone substantially decreased leaf water potential in cv White Cascade but not in cv Capri or White Magic. Sulphur dioxide did not affect leaf water potential but delayed ozone-induced changes. Cultivar sensitivity to ozone-induced changes in leaf water potential was not related to cultivar sensitivity to ozone-induced visible injury.

Ozone exposure affects leaf wettability and tree water balance

NARCIS (Netherlands)

Schreuder, M.D.J.; Hove, van L.W.A.; Brewer, C.A.

2001-01-01

Relatively little is known about the influences of growing-season background ozone (O3) concentrations on leaf cuticles and foliar water loss. Using fumigation chambers, leaf wettability and foliar water loss were studied in two poplar species, Populus nigra and P. euramericana, and a conifer,

Comparative antimicrobial activities of aloe vera gel and leaf ...

African Journals Online (AJOL)

The comparative antimicrobial activities of the gel and leaf of Aloe vera were tested against Staphylococcus aureus, Pseudomonas aeruginosa, Trichophyton mentagraphytes, T. schoeleinii, Microsporium canis and Candida albicans. Ethanol was used for the extraction of the leaf after obtaining the gel from it. Antimicrobial ...

Soil Characteristics, Microbial Compostion of Plot, Leaf Count and ...

African Journals Online (AJOL)

Soil Characteristics, Microbial Compostion of Plot, Leaf Count and Sprout Studies of Cocoyam ( Colocasia [Schott] and Xanthosoma [Schott], Araceae) Collected in Edo State, ... Science, Technology and Arts Research Journal ... Government Areas (LGA) in Edo state and describe them based on leaf count and sprout

GOLD IS EARNED FROM THE PRODUCTION OF THAI GOLD LEAF

Directory of Open Access Journals (Sweden)

Dirk Bax

2010-06-01

Full Text Available Thai people like to cover sacred objects or things dear to them with gold leaf.. Statues of Buddha are sometimes covered with so many layers of gold leaf that they become formless figures, that can hardly be recognized. Portraits of beloved ancestors, statues of elephants and grave tombs are often covered with gold leaf. If one considers the number of Thai people and the popularity of the habit, the amount of gold involved could be considerable.

Climate controls photosynthetic capacity more than leaf nitrogen contents

Science.gov (United States)

Ali, A. A.; Xu, C.; McDowell, N. G.

2013-12-01

Global vegetation models continue to lack the ability to make reliable predictions because the photosynthetic capacity varies a lot with growth conditions, season and among species. It is likely that vegetation models link photosynthetic capacity to concurrent changes in leaf nitrogen content only. To improve the predictions of the vegetation models, there is an urgent need to review species growth conditions and their seasonal response to changing climate. We sampled the global distribution of the Vcmax (maximum carboxylation rates) data of various species across different environmental gradients from the literature and standardized its value to 25 degree Celcius. We found that species explained the largest variation in (1) the photosynthetic capacity and (2) the proportion of nitrogen allocated for rubisco (PNcb). Surprisingly, climate variables explained more variations in photosynthetic capacity as well as PNcb than leaf nitrogen content and/or specific leaf area. The chief climate variables that explain variation in photosynthesis and PNcb were radiation, temperature and daylength. Our analysis suggests that species have the greatest control over photosynthesis and PNcb. Further, compared to leaf nitrogen content and/or specific leaf area, climate variables have more control over photosynthesis and PNcb. Therefore, climate variables should be incorporated in the global vegetation models when making predictions about the photosynthetic capacity.

DETERMINATION OF LEAF AREA AND PLANT COVER BY USING DIGITAL IMAGE PROCESSING

OpenAIRE

LŐKE, ZS.; SOÓS, G.

2002-01-01

The development of different crop models, and crop simulation models in particular, pointed out the importance of quantifying the exact value of the leaf area. To measure the leaf size of plants of pinnatifid form, automatic, portable leaf area meters are necessary. In most places these instruments are not available to measure the assimilatory surface size of crops with special leaf shapes. Any cheap and effective method, that could replace the application of expensive portable area meters co...

Monosaccharide analysis of succulent leaf tissue in Aloe

DEFF Research Database (Denmark)

Grace, Olwen Megan; Dzajic, Amra; Jäger, Anna

2013-01-01

in the genus Aloe using a predictive phylogenetic approach. Methodology – Monosaccharide composition was assessed in 31species, representing the morphological and taxonomic diversity of Aloe sensu stricto. Leaf mesophyll polysaccharides were partially hydrolysed in a trifluoroacetic acid (TFA)-SilA assay......Introduction – The succulent leaf mesophyll in Aloe species supports a burgeoning natural products industry, particularly in Africa. Comparative data necessary to prioritise species with economic potential have been lacking. Objective – To survey leaf mesophyll monosaccharide composition....... Oximes and trimethylsilyl ether products were detected by GC-MS. Constituent monosaccharides accounting for the greatest variation among species were identified by principal component analysis. Two plant DNA barcoding regions were sequenced in 28 of the sampled species and the resulting maximum...

Red Guava Leaf Harvesting Impact on Flavonoid Optimation in Different Growth Phases

Directory of Open Access Journals (Sweden)

MUNIF GHULAMAHDI

2011-06-01

Full Text Available Harvesting process is a critical time to identify the quality of raw material for traditional medicine. The time and harvesting techniques, drying process after harvesting, and processing to make the simplicia, are the crucial role to make the good quality of the natural product. On the other hand, there is a lack of general understanding and appreciation about the processes involved in governing shoot and tree growth and development, i.e. red guava. The research objective was to evaluate the influence of leaf harvesting and growth phases on red guava for flavonoid production as antioxidant. Randomized factorial block design in time were laid out with two factors and followed by Duncan’s multiple range test. The treatments were the amount of leaf harvested on tertiary branches (0, 25, 50, and 100% and growth phases of the plant (vegetative and generative. Leaf harvesting 25% on tertiary branches significantly increased the leaf number (766.3 tree-1 and the number of new quarternary branches, decreasing leaf area index (LAI and leaf dry weight at the end of the experiment (22 weeks of observation/WO. The highest leaf dry weight (156.94 g tree-1 and LAI (0.47 was found in harvesting 25% tertiary branches. Harvesting 100% leaf on tertiary branches in vegetative phase significantly produced the lowest flavonoid production (7.82 g tree-1. The result suggested that flavonoid production from red guava leaves should be done by harvesting 50% leaf on tertiary branches in generative phase can be used to produce the highest flavonoid (89.90 g tree-1.

Variable depth recursion algorithm for leaf sequencing

International Nuclear Information System (INIS)

Siochi, R. Alfredo C.

2007-01-01

The processes of extraction and sweep are basic segmentation steps that are used in leaf sequencing algorithms. A modified version of a commercial leaf sequencer changed the way that the extracts are selected and expanded the search space, but the modification maintained the basic search paradigm of evaluating multiple solutions, each one consisting of up to 12 extracts and a sweep sequence. While it generated the best solutions compared to other published algorithms, it used more computation time. A new, faster algorithm selects one extract at a time but calls itself as an evaluation function a user-specified number of times, after which it uses the bidirectional sweeping window algorithm as the final evaluation function. To achieve a performance comparable to that of the modified commercial leaf sequencer, 2-3 calls were needed, and in all test cases, there were only slight improvements beyond two calls. For the 13 clinical test maps, computation speeds improved by a factor between 12 and 43, depending on the constraints, namely the ability to interdigitate and the avoidance of the tongue-and-groove under dose. The new algorithm was compared to the original and modified versions of the commercial leaf sequencer. It was also compared to other published algorithms for 1400, random, 15x15, test maps with 3-16 intensity levels. In every single case the new algorithm provided the best solution

Somatic embryogenesis and plant regeneration from leaf explants of ...

African Journals Online (AJOL)

An attempt was made to study the somatic embryogenesis and plant regeneration from the in vitro leaf explants of Rumex vesicarius L. a renowned medicinal plant, which belongs to polygonaceae family. Effective in vitro regeneration of R. vesicarius was achieved via young leaf derived somatic embryo cultures.

Phytochemical constituents and ethnobotany of the leaf extract of ...

African Journals Online (AJOL)

The phytochemical screening and ethno botanical importance of the leaf of Vernonia amygdalina Del. were investigated. The secondary metabolites in the leaf were identified to establish a relationship between them and their therapeutic properties. The leaves were sun dried, pulverized and sieved. The resulting powdered ...

Effect of drought stress on leaf soluble sugar content, leaf rolling index and relative water content of proso millet (Panicum miliaceum L. genotypes

Directory of Open Access Journals (Sweden)

mohamad javad seghatol eslami

2009-06-01

Full Text Available With respect to water shortage in arid and semi- arid regions, the study about drought stress effects on crop plants and selection of resistance cultivars, are among the most important goals in the agricultural researches. In order to examine drought stress effects on millet, an experiment was conducted in Birjand and Sarbisheh, simultaneously. In this experiment, five irrigation treatments (well-watered, drought stress in vegetative stage, in ear emergence stage, in seed filling stage and in vegetative and seed filling stage and five proso millet genotypes (Native, K-C-M.2, K-C-M.4, K-C-M.6 and K-C-M.9 were compared in a split plot design along with three replications. Drought stress increased grain protein content, leaf rolling index and soluble sugars concentration and decreased seed germination and leaf RWC. Although seed protein content and germination percentage of genotypes were not significantly different, there were some differences among leaf rolling index, RWC and soluble sugar content of these genotypes. The results of this study indicated that leaf sugar content, RWC and leaf rolling index can not be considered as the only parameters for selection of high yield genotypes. Therefore, it is recommended that some other factors should also be used apart from the above mentioned ones.

Monitoring leaf photosynthesis with canopy spectral reflectance in rice

International Nuclear Information System (INIS)

Tian, Y.; Zhu, Y.; Cao, W.

2005-01-01

We determined the quantitative relationships between leaf photosynthetic characteristics (LPC) and canopy spectral reflectance under different water supply and nitrogen application rates in rice plants. The responses of reflectance at red radiation (680 nm) to different water contents and N rates were parallel to those of leaf net photosynthetic rate (PN). The relationships of reflectance at 680 nm and ratio index of R(810,680) (near infrared/red) to PN of different leaf positions and layers indicated that the top two full leaves were the best positions for quantitative monitoring of PN with remote sensing technique, and the index R(810,680) was the best ratio index for evaluating LPC. Testing of the models with independent data sets indicated that R(810,680) could well estimate PN of the top two leaves and canopy leaf photosynthetic potential. Hence R(810,680) can be used to monitor LPC in rice under diverse growing conditions

Primate numts and reticulate evolution of capped and golden leaf ...

Indian Academy of Sciences (India)

PRAKASH KUMAR

A recent phylogenetic study of langurs and leaf monkeys of South Asia suggested a reticulate evolution of capped and golden leaf ..... Accordingly, transversions were weighted .... lineages. Most taxonomic schemes published till date place.

Beyond leaf color: Comparing camera-based phenological metrics with leaf biochemical, biophysical, and spectral properties throughout the growing season of a temperate deciduous forest

Science.gov (United States)

Yang, Xi; Tang, Jianwu; Mustard, John F.

2014-03-01

Plant phenology, a sensitive indicator of climate change, influences vegetation-atmosphere interactions by changing the carbon and water cycles from local to global scales. Camera-based phenological observations of the color changes of the vegetation canopy throughout the growing season have become popular in recent years. However, the linkages between camera phenological metrics and leaf biochemical, biophysical, and spectral properties are elusive. We measured key leaf properties including chlorophyll concentration and leaf reflectance on a weekly basis from June to November 2011 in a white oak forest on the island of Martha's Vineyard, Massachusetts, USA. Concurrently, we used a digital camera to automatically acquire daily pictures of the tree canopies. We found that there was a mismatch between the camera-based phenological metric for the canopy greenness (green chromatic coordinate, gcc) and the total chlorophyll and carotenoids concentration and leaf mass per area during late spring/early summer. The seasonal peak of gcc is approximately 20 days earlier than the peak of the total chlorophyll concentration. During the fall, both canopy and leaf redness were significantly correlated with the vegetation index for anthocyanin concentration, opening a new window to quantify vegetation senescence remotely. Satellite- and camera-based vegetation indices agreed well, suggesting that camera-based observations can be used as the ground validation for satellites. Using the high-temporal resolution dataset of leaf biochemical, biophysical, and spectral properties, our results show the strengths and potential uncertainties to use canopy color as the proxy of ecosystem functioning.

Leaf rust of cultivated barley: pathology and control.

Science.gov (United States)

Park, Robert F; Golegaonkar, Prashant G; Derevnina, Lida; Sandhu, Karanjeet S; Karaoglu, Haydar; Elmansour, Huda M; Dracatos, Peter M; Singh, Davinder

2015-01-01

Leaf rust of barley is caused by the macrocyclic, heteroecious rust pathogen Puccinia hordei, with aecia reported from selected species of the genera Ornithogalum, Leopoldia, and Dipcadi, and uredinia and telia occurring on Hordeum vulgare, H. vulgare ssp. spontaneum, Hordeum bulbosum, and Hordeum murinum, on which distinct parasitic specialization occurs. Although Puccinia hordei is sporadic in its occurrence, it is probably the most common and widely distributed rust disease of barley. Leaf rust has increased in importance in recent decades in temperate barley-growing regions, presumably because of more intensive agricultural practices. Although total crop loss does not occur, under epidemic conditions yield reductions of up to 62% have been reported in susceptible varieties. Leaf rust is primarily controlled by the use of resistant cultivars, and, to date, 21 seedling resistance genes and two adult plant resistance (APR) genes have been identified. Virulence has been detected for most seedling resistance genes but is unknown for the APR genes Rph20 and Rph23. Other potentially new sources of APR have been reported, and additivity has been described for some of these resistances. Approaches to achieving durable resistance to leaf rust in barley are discussed.

Leaf, stem bark and fruit anatomy of zanthoxylum armatum dc. (rutaceae)

International Nuclear Information System (INIS)

Barkatullah, A.; Ibrar, M.; Jelani, G.; Ahmad, I.

2014-01-01

Zanthoxylum armatum DC. (Rutaceae) is an important medicinal plant. The present study deals with anatomical exploration of the leaf, stem bark and fruit of this plant. Leaf of Z. armatum is bifacial, compound and punctate with glabrous surfaces having a single layer of epidermis and palisade mesophyll. The leaf has a Palisade ratio ranged from 6.00 to 9.00 (8.2 +- 0.32). Vein islets and vein termination number were 14-21 (16.8 +- 0.64) and 17-21 (19.1 +- 0.43) per mm2 respectively. The vein-islets were quite distinct with squaresh, elongated, polygonal or irregular in shape bounding many forked and unforked vascular branches. Adaxial surface of Z. armatum leaf midrib was planoconvex while the abaxial surface was semicircular in appearance. The diagnostic feature of the leaf was the complete absence of any kind of trichomes or any other appendages. The leaf showed prominent oil cavities. Nine types of stomata with different frequencies and other dimensions were observed. Brachparatetracytic stomata was the most frequent stoma (80%) followed by actinostephanocytic (40%) and then straucytic and brachyparacytic (30%) each. Hemiparacytic and stomatal cluster were the rarely occurring stomata (10% each) present on the lower epidermis of the leaf. Stomatal cluster, which is considered to be a special leaf epidermal feature and reported only in few genera of vascular plants, was also recorded in this plant. Bark and fruit anatomy of Z. armatum showed different tissue arrangement. The seed was non endospermic and contains an elongated embryo. The present study will be helpful in the phylogeny and taxonomic description of this important medicinal plant. (author)

Influence of heat processing on the bioaccessibility of zinc and iron from cereals and pulses consumed in India.

Science.gov (United States)

Hemalatha, Sreeramaiah; Platel, Kalpana; Srinivasan, Krishnapura

2007-01-01

Influence of heat processing on the bioaccessibility of zinc and iron from food grains consumed in India was evaluated. Cereals - rice (Oryza sativa), finger millet (Eleusine coracana), sorghum (Sorghum vulgare), wheat (Triticum aestivum), and maize (Zea mays), and pulses - chickpea (Cicer arietinum) - whole and decorticated, green gram (Phaseolus aureus) - whole and decorticated, decorticated black gram (Phaseolus mungo), decorticated red gram (Cajanus cajan), cowpea (Vigna catjang), and French bean (Phaseolus vulgaris) were examined for zinc and iron bioaccessibility by employing an in vitro dialysability procedure. Both pressure-cooking and microwave heating were tested for their influence on mineral bioaccessibility. Zinc bioaccessibility from food grains was considerably reduced upon pressure-cooking, especially in pulses. Among cereals, pressure-cooking decreased zinc bioaccessibility by 63% and 57% in finger millet and rice, respectively. All the pressure-cooked cereals showed similar percent zinc bioaccessibility with the exception of finger millet. Bioaccessibility of zinc from pulses was generally lower as a result of pressure-cooking or microwave heating. The decrease in bioaccessibility of zinc caused by microwave heating ranged from 11.4% in chickpea (whole) to 63% in cowpea. Decrease in zinc bioaccessibility was 48% in pressure-cooked whole chickpea, 45% and 55% in pressure-cooked or microwave-heated whole green gram, 32% and 22% in pressure-cooked or microwave-heated decorticated green gram, and 45% in microwave-heated black gram. Iron bioaccessibility, on the other hand, was significantly enhanced generally from all the food grains studied upon heat treatment. Thus, heat treatment of grains produced contrasting effect on zinc and iron bioaccessibility.

Brief communication: effect of coca-leaf chewing on salivary progesterone assays.

Science.gov (United States)

Vitzthum, V J; von Dornum, M; Ellison, P T

1993-12-01

Although there is evidence for reduced fertility in Andean and Himalayan populations at higher altitudes, factors other than hypoxia may be primarily responsible. A valuable approach in the investigation of these fertility determinants is the use of salivary steroid assays. However, coca-leaf chewing--a ubiquitous practice among high altitude Andean populations--has negative consequences for the accurate measurement of ovarian steroids. This report evaluates the effects of coca-leaf chewing on assays of salivary progesterone. Study participants include naive and habitual users of coca leaf from La Paz and El Alto, Bolivia. Approximately 300 saliva samples were collected immediately before, during, and after coca-leaf chewing. The series includes samples with and without the alkaloid enhancer typically used by coca-leaf chewers. Coca chewing produces false salivary progesterone values that mimic luteal phase values. On the basis of this study, an appropriate protocol is developed for the collection of salivary samples in coca-leaf chewing populations. These results verify the feasibility of salivary assays, even for very difficult field conditions, and highlight the necessity of establishing suitable collection procedures before full field implementation of saliva sampling.

Variation of leaf margin serration in Populus nigra of industrial dumps

Directory of Open Access Journals (Sweden)

Yu. A. Shtirs

2017-07-01

Full Text Available The variability of leaf margin serration of Populus nigra L. in conditions of industrial dumps (coal mines dumps and overburden dumps and city park is estimated. The value of this indicator is in the range from 1.25 to 1.76 and significantly increases along the gradient: coal mines dumps – overburden dumps – city park. From the number of selected gradations of P. nigra leaf blades, the gradation with values of 1.45-1.55 is most pronounced according to the analyzed index for industrial dumps, for the park – with the values of 1.55-1.65. The degree of serration of edge leaf blade is characterized by low values of variation – coefficient of variation is less than 10.0%. We registered the significant positive correlation between the average values of leaf margin serration and the length of P. nigra leaf blade.

Editorial

Directory of Open Access Journals (Sweden)

Jo Mynard

2012-09-01

Full Text Available Issues of SiSAL Journal have a good international representation and this current issue is no exception. Contributions come from Mexico, Hong Kong, Japan and Iran. Although this is a general issue of SiSAL Journal, I have identified some salient themes coming through in the articles. These are: training for autonomous learning; scaffolding self-access use; and beliefs about learning and using the L2.

Nanofibrillated cellulose (NFC) as a potential reinforcement for high performance cement mortar composites

OpenAIRE

Ardanuy Raso, Mònica; Claramunt Blanes, Josep; Arévalo Peces, Raquel; Parés Sabatés, Ferran; Aracri, Elisabetta; Vidal Lluciá, Teresa

2012-01-01

In this work, nanofibrillated cellulose (NFC) has been evaluated as a potential reinforcement for cement mortar composites. Two types of vegetable fibres with different composition and properties (cellulose content and microfibrillar angle), sisal, and cotton linters pulps, were initially characterized in order to assess their reinforcement capability. Sisal pulp was found to be most suitable as reinforcement for their brittle cementitious matrix. Nanofibrillated cellulose was produced by th...

Cassava brown streak disease effects on leaf metabolites and ...

African Journals Online (AJOL)

Cassava brown streak disease effects on leaf metabolites and pigment accumulation. ... Total reducing sugar and starch content also dropped significantly (-30 and -60%, respectively), much as NASE 14 maintained a relatively higher amount of carbohydrates. Leaf protein levels were significantly reduced at a rate of 0.07 ...

Effect Of Walnut Leaf, Coriander And Pomegranate On Blood ...

African Journals Online (AJOL)

Mechanism of most of herbal used for diabetes mellitus treatment has not been well defined. This study was performed to investigate hypoglycemic effect of walnut leaf (Juglans regia L.), coriander leaf (Coriandrum sativum L.) or pomegranate seed (Punica granatum L.), and their possible role on pancreatic tissue. Diabetes ...

Leaf water stable isotopes and water transport outside the xylem.

Science.gov (United States)

Barbour, M M; Farquhar, G D; Buckley, T N

2017-06-01

How water moves through leaves, and where the phase change from liquid to vapour occurs within leaves, remain largely mysterious. Some time ago, we suggested that the stable isotope composition of leaf water may contain information on transport pathways beyond the xylem, through differences in the development of gradients in enrichment within the various pathways. Subsequent testing of this suggestion provided ambiguous results and even questioned the existence of gradients in enrichment within the mesophyll. In this review, we bring together recent theoretical developments in understanding leaf water transport pathways and stable isotope theory to map a path for future work into understanding pathways of water transport and leaf water stable isotope composition. We emphasize the need for a spatially, anatomically and isotopically explicit model of leaf water transport. © 2016 John Wiley & Sons Ltd.

Habitat Modification by the Leaf-Cutter Ant, Atta cephalotes, and Patterns of Leaf-Litter Arthropod Communities.

Science.gov (United States)

Wells, Rachel L; Murphy, Serena K; Moran, Matthew D

2017-12-08

Ecosystem engineers are profoundly important in many biological communities. A Neotropical taxonomic group considered to have engineering effects is the Formicidae (ants). Leaf-cutter ants (LCAs), in particular, which form extensive colonies of millions of individuals, can be important ecosystem engineers in these environments. While the effects of LCAs on plant community structure and soil chemistry are well-studied, their effects on consumers are poorly understood. Therefore, we examined the indirect effects of the LCA Atta cephalotes L. on the leaf-litter arthropod community. We compared abundance and diversity patterns at ant nests to areas distant from nests, utilizing both a factorial design and gradient analysis for both nocturnal and diurnal arthropods. We found that arthropod abundance and diversity was significantly lower for multiple taxonomic groups and trophic levels near leaf-cutter nests, and this pattern was strongest at night. Exceptions to this pattern included two morphospecies of Collembola that were more abundant on nests, suggesting some specialization for these species. For the gradient analysis, abundance increased exponentially for most groups of arthropods. However, for the dominant arthropod species, the amphipod Cerrorchestia hyloraina Lindeman, a quadratic function was the best fit curvilinear model for abundance. It appeared that C. hyloraina had maximal abundance at the transition between nest site and less disturbed forest. These results indicate that LCA activity has a strong effect on the leaf-litter arthropod community, adding to spatial heterogeneity within neotropical forests. These effects may translate into changes in important ecological processes such as nutrient cycling and food web function. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Estimativa da área foliar de Crambe abyssinica por discos foliares e por fotos digitais Estimate leaf area of Crambe abyssinica for leaf discs and digital photos

Directory of Open Access Journals (Sweden)

Marcos Toebe

2010-02-01

Full Text Available A área foliar é importante na determinação do crescimento e desenvolvimento das culturas agrícolas. Assim, os objetivos do trabalho foram comparar os métodos de discos foliares e de fotos digitais na estimativa da área foliar de Crambe abyssinica e modelar a área foliar em função do comprimento (C, da largura (L e ou do produto comprimento vezes largura (CxL de diferentes tamanhos de folhas. Para isso, em 308 folhas, foram determinados a área foliar, o comprimento, a largura e o produto comprimento vezes largura por meio dos métodos de discos foliares e de fotos digitais. Em seguida, foram comparados os métodos por meio do coeficiente de correlação linear entre a área foliar. A seguir, em cada método, modelou-se a área foliar (Y em função do C, da L e do CxL, por meio dos modelos: linear, linear simples, quadrático, geométrico e exponencial. Os coeficientes de correlação linear de Pearson e de Spearman entre a área foliar dos métodos de discos foliares e de fotos digitais foram de 0,9917 e 0,9889, respectivamente, o que revela métodos concordantes. Em ambos os métodos, os modelos quadráticos e geométricos apresentaram os melhores coeficientes de determinação da área foliar em função do comprimento e da largura das folhas. A largura da folha é a variável que melhor estima a área foliar. O método de fotos digitais pode ser utilizado para estimar a área foliar de crambe.Leaf area is important in determining the growth and development of agricultural crops. The aim of this study was to compare the methods of leaf discs and digital photos in estimating leaf area of Crambe abyssinica, and model leaf area according to length (C, width (L and/ or the product of length width (CxL for different sizes of leaves. For this, in 308 leaves it was determined the leaf area, length, width and the product of length width using the methods of leaf discs and digital photos. Then the methods were compared using the linear

Performance of broiler chickens fed on Moringa oleifera leaf meal ...

African Journals Online (AJOL)

Performance of broiler chickens fed on Moringa oleifera leaf meal ... This exploratory study was conducted to investigate the effect of Moringa oleifera leaf meal ... ratio were evaluated for the individual replicate of each dietary treatment.

Genetic and Developmental Basis for Increased Leaf Thickness in the Arabidopsis Cvi Ecotype

Directory of Open Access Journals (Sweden)

Viktoriya Coneva

2018-03-01

Full Text Available Leaf thickness is a quantitative trait that is associated with the ability of plants to occupy dry, high irradiance environments. Despite its importance, leaf thickness has been difficult to measure reproducibly, which has impeded progress in understanding its genetic basis, and the associated anatomical mechanisms that pattern it. Here, we used a custom-built dual confocal profilometer device to measure leaf thickness in the Arabidopsis Ler × Cvi recombinant inbred line population and found statistical support for four quantitative trait loci (QTL associated with this trait. We used publically available data for a suite of traits relating to flowering time and growth responses to light quality and show that three of the four leaf thickness QTL coincide with QTL for at least one of these traits. Using time course photography, we quantified the relative growth rate and the pace of rosette leaf initiation in the Ler and Cvi ecotypes. We found that Cvi rosettes grow slower than Ler, both in terms of the rate of leaf initiation and the overall rate of biomass accumulation. Collectively, these data suggest that leaf thickness is tightly linked with physiological status and may present a tradeoff between the ability to withstand stress and rapid vegetative growth. To understand the anatomical basis of leaf thickness, we compared cross-sections of Cvi and Ler leaves and show that Cvi palisade mesophyll cells elongate anisotropically contributing to leaf thickness. Flow cytometry of whole leaves show that endopolyploidy accompanies thicker leaves in Cvi. Overall, our data suggest that mechanistically, an altered schedule of cellular events affecting endopolyploidy and increasing palisade mesophyll cell length contribute to increase of leaf thickness in Cvi. Ultimately, knowledge of the genetic basis and developmental trajectory leaf thickness will inform the mechanisms by which natural selection acts to produce variation in this adaptive trait.

Outside-xylem pathways, not xylem embolism, drive leaf hydraulic decline with dehydration

Science.gov (United States)

Leaf hydraulic supply is crucial to enable the maintenance of open stomata for CO2 capture and plant growth. During drought-induced leaf dehydration, the capacity for water flow through the leaf (Kleaf) declines, a phenomenon surprisingly attributed for the past fifty years solely to the formation o...

Formation of adventitious roots on green leaf cuttings of Phaseolus vulgaris L.

NARCIS (Netherlands)

Oppenoorth, Johanna Margriet

1980-01-01

n this thesis the development of adventitious roots on green leaf cuttings of Phaseolus vulgaris L. is studies. The use of green leaf cuttings has the advantage that the leaf blade provides the developing roots inthe petiole with all the nutrients required, a disadvantage is that the composition of

Local effect of zoledronic acid on new bone formation in posterolateral spinal fusion with demineralized bone matrix in a murine model.

Science.gov (United States)

Zwolak, Pawel; Farei-Campagna, Jan; Jentzsch, Thorsten; von Rechenberg, Brigitte; Werner, Clément M

2018-01-01

Posterolateral spinal fusion is a common orthopaedic surgery performed to treat degenerative and traumatic deformities of the spinal column. In posteriolateral spinal fusion, different osteoinductive demineralized bone matrix products have been previously investigated. We evaluated the effect of locally applied zoledronic acid in combination with commercially available demineralized bone matrix putty on new bone formation in posterolateral spinal fusion in a murine in vivo model. A posterolateral sacral spine fusion in murine model was used to evaluate the new bone formation. We used the sacral spine fusion model to model the clinical situation in which a bone graft or demineralized bone matrix is applied after dorsal instrumentation of the spine. In our study, group 1 received decortications only (n = 10), group 2 received decortication, and absorbable collagen sponge carrier, group 3 received decortication and absorbable collagen sponge carrier with zoledronic acid in dose 10 µg, group 4 received demineralized bone matrix putty (DBM putty) plus decortication (n = 10), and group 5 received DBM putty, decortication and locally applied zoledronic acid in dose 10 µg. Imaging was performed using MicroCT for new bone formation assessment. Also, murine spines were harvested for histopathological analysis 10 weeks after surgery. The surgery performed through midline posterior approach was reproducible. In group with decortication alone there was no new bone formation. Application of demineralized bone matrix putty alone produced new bone formation which bridged the S1-S4 laminae. Local application of zoledronic acid to demineralized bone matrix putty resulted in significant increase of new bone formation as compared to demineralized bone matrix putty group alone. A single local application of zoledronic acid with DBM putty during posterolateral fusion in sacral murine spine model increased significantly new bone formation in situ in our model. Therefore, our

Analysis of Peanut Leaf Proteome

DEFF Research Database (Denmark)

Ramesh, R.; Suravajhala, Prashanth; Pechan, T.

2010-01-01

Peanut (Arachis hypogaea) is one of the most important sources of plant protein. Current selection of genotypes requires molecular characterization of available populations. Peanut genome database has several EST cDNAs which can be used to analyze gene expression. Analysis of proteins is a direct...... approach to define function of their associated genes. Proteome analysis linked to genome sequence information is critical for functional genomics. However, the available protein expression data is extremely inadequate. Proteome analysis of peanut leaf was conducted using two-dimensional gel...... electrophoresis in combination with sequence identification using MALDI/TOF to determine their identity and function related to growth, development and responses to stresses. Peanut leaf proteins were resolved into 300 polypeptides with pI values between 3.5 and 8.0 and relative molecular masses from 12 to 100 k...

Mueller matrix of a dicot leaf

Science.gov (United States)

Vanderbilt, Vern C.; Daughtry, Craig S. T.

2012-06-01

A better understanding of the information contained in the spectral, polarized bidirectional reflectance and transmittance of leaves may lead to improved techniques for identifying plant species in remotely sensed imagery as well as better estimates of plant moisture and nutritional status. Here we report an investigation of the optical polarizing properties of several leaves of one species, Cannabis sativa, represented by a 3x3 Mueller matrix measured over the wavelength region 400-2,400 nm. Our results support the hypothesis that the leaf surface alters the polarization of incident light - polarizing off nadir, unpolarized incident light, for example - while the leaf volume tends to depolarized incident polarized light.

Comparison of dosimetric properties of three commercial multi leaf collimator systems

International Nuclear Information System (INIS)

Hoever, K.H.; Hesse, B.M.; Haering, P.; Rhein, B.; Bannach, B.; Doll, T.; Doerner, K.J.

1996-01-01

Purpose: The dosimetric properties of different designs of multi leaf collimators used for the generation of irregular fields will be measured and compared with each other. Using multi leaf collimators is a practical method of achieving conformal therapy. The use for complex conformal treatment fields to be given in either in static or dynamic mode depends much on the leaf end penumbra and the leaf side penumbra as well as the transmission through the leafs. Penumbra and leakage caused by the leaves therefore are of special interest in this intercomparison. Material and Methods: To investigate the dosimetric properties of three multi leaf collimators of different technical design, measurements have been taken at two different facilities. Until now, comparative measurements have been performed for the following devices. The new Siemens double focusing MLC with 29 opposite leaf pairs, installed at the Mevatron Experimental in the German Cancer Research Center, Heidelberg. The energy used was 15 MV and 6 MV. The Philips quasi-double focusing MLC with 40 opposite leaf pairs, installed at the SL25 in the University Duesseldorf. The leaves move in a plane rather than on a circular arc and have rounded ends to reduce penumbra. The energy used was 25 MV and 6 MV. The Leibinger non-focusing micro-MLC with 40 opposite leaf pairs. This MLC was specially designed for stereotactic irradiation of the brain. The comparative study is to be continued and extended to involve additional devices in the future. Both, the film densitometry and a newly designed ten-bit Beam Imaging System BIS-710 developed by Wellhoefer company were used. The BIS-710 was developed especially for quantitative dose measuring, whereas most of the existing Portal Imaging Systems are used for image display only. The BIS-710 contains a camera for 10-bit digital data output. The size of each of the 512 x 512 detector elements is 0.6 mm x 0.6 mm Results: Measurements taken with the BIS-710 and with film

Effect of temperature on accumulation of chlorophylls and leaf ...

African Journals Online (AJOL)

White young shoots from albino tea cultivars have high level of amino acids and are rare and valuable materials for processing green tea. The effects of temperature on leaf colour, accumulation of chlorophylls and leaf ultrastructures of an albino tea cultivar 'Xiaxueya' were investigated. The study showed that the shoot ...

Antimicrobial activity of the aqueous, methanol and chloroform leaf ...

African Journals Online (AJOL)

The minimum inhibitory concentration (MIC) of methanol leaf extract show least activity against Yersinia enterocolitica and Pseudomonas aeruginosa (MIC = 100 mg/ml) and higher activity of MIC at 50 mg/ml against the other bacterial test organisms. The chloroform leaf extract MIC of 100 mg/ml had least activity against ...

Impairment of leaf photosynthesis after insect herbivory or mechanical injury on common milkweed, Asclepias syriaca.

Science.gov (United States)

Delaney, K J; Haile, F J; Peterson, R K D; Higley, L G

2008-10-01

Insect herbivory has variable consequences on plant physiology, growth, and reproduction. In some plants, herbivory reduces photosynthetic rate (Pn) activity on remaining tissue of injured leaves. We sought to better understand the influence of leaf injury on Pn of common milkweed, Asclepias syriaca (Asclepiadaceae), leaves. Initially, we tested whether Pn reductions occurred after insect herbivory or mechanical injury. We also (1) examined the duration of photosynthetic recovery, (2) compared mechanical injury with insect herbivory, (3) studied the relationship between leaf Pn with leaf injury intensity, and (4) considered uninjured leaf compensatory Pn responses neighboring an injured leaf. Leaf Pn was significantly reduced on mechanically injured or insect-fed leaves in all reported experiments except one, so some factor(s) (cardiac glycoside induction, reproductive investment, and water stress) likely interacts with leaf injury to influence whether Pn impairment occurs. Milkweed tussock moth larval herbivory, Euchaetes egle L. (Arctiidae), impaired leaf Pn more severely than mechanical injury in one experiment. Duration of Pn impairment lasted > 5 d to indicate high leaf Pn sensitivity to injury, but Pn recovery occurred within 13 d in one experiment. The degree of Pn reduction was more severe from E. egle herbivory than similar levels of mechanical tissue removal. Negative linear relationships characterized leaf Pn with percentage tissue loss from single E. egle-fed leaves and mechanically injured leaves and suggested that the signal to trigger leaf Pn impairment on remaining tissue of an injured leaf was amplified by additional tissue loss. Finally, neighboring uninjured leaves to an E. egle-fed leaf had a small (approximately 10%) degree of compensatory Pn to partly offset tissue loss and injured leaf Pn impairment.

Increasing leaf longevity and disease resistance by altering salicylic acid catabolism

Energy Technology Data Exchange (ETDEWEB)

Gan, Susheng; Zhang, Kewei

2018-01-23

The present invention relates to a transgenic plant having an altered level of salicylic acid 3-hydroxylase ("S3H") protein, compared to that of a non-transgenic plant, where the transgenic plant displays an altered leaf senescence phenotype, relative to a non-transgenic plant. The present invention relates to a mutant plant comprising an inactivated gene encoding S3H protein, where the mutant plant displays a premature or precocious leaf senescence phenotype, relative to a non-mutant plant. The present invention also relates to methods for promoting premature or precocious leaf senescence in a plant, delaying leaf senescence in a plant, and making a mutant plant having a decreased level of S3H protein compared to that of a non-mutant plant, where the mutant plant displays a premature or precocious leaf senescence phenotype relative to a non-mutant plant. The present invention also relates to inducing or promoting pathogen resistance in plants.

Evaluation of Jacaranda mimosifolia T. (Stans) leaf meal as ...

African Journals Online (AJOL)

The economic benefit analysis indicated that as the leaf meal increased in the diets the cost of production of the broilers decreased. Jacaranda leaf meal could be best utilized at 5.0% level of inclusion though the 7.5% levels broilers attained market size in a recorded time. Animal Production Research Advances Vol.

Quantitative study of Xanthosoma violaceum leaf surfaces using RIMAPS and variogram techniques.

Science.gov (United States)

Favret, Eduardo A; Fuentes, Néstor O; Molina, Ana M

2006-08-01

Two new imaging techniques (rotated image with maximum averaged power spectrum (RIMAPS) and variogram) are presented for the study and description of leaf surfaces. Xanthosoma violaceum was analyzed to illustrate the characteristics of both techniques. Both techniques produce a quantitative description of leaf surface topography. RIMAPS combines digitized images rotation with Fourier transform, and it is used to detect patterns orientation and characteristics of surface topography. Variogram relates the mathematical variance of a surface with the area of the sample window observed. It gives the typical scale lengths of the surface patterns. RIMAPS detects the morphological variations of the surface topography pattern between fresh and dried (herbarium) samples of the leaf. The variogram method finds the characteristic dimensions of the leaf microstructure, i.e., cell length, papillae diameter, etc., showing that there are not significant differences between dry and fresh samples. The results obtained show the robustness of RIMAPS and variogram analyses to detect, distinguish, and characterize leaf surfaces, as well as give scale lengths. Both techniques are tools for the biologist to study variations of the leaf surface when different patterns are present. The use of RIMAPS and variogram opens a wide spectrum of possibilities by providing a systematic, quantitative description of the leaf surface topography.

Seasonal Canopy Temperatures for Normal and Okra Leaf Cotton under Variable Irrigation in the Field

Directory of Open Access Journals (Sweden)

James R. Mahan

2016-11-01

Full Text Available Temperature affects a number of physiological factors in plants and is related to water use, yield and quality in many crop species. Seasonal canopy temperature, measured with infrared thermometers, is often used in conjunction with environmental factors (e.g., air temperature, humidity, solar radiation to assess crop stress and management actions in cotton. Normal and okra leaf shapes in cotton have been associated with differences in water use and canopy temperature. The okra leaf shape in cotton is generally expected to result in lower water use and lower canopy temperatures, relative to normal leaf, under water deficits. In this study canopy temperatures were monitored in okra and normal leaf varieties for a growing season at four irrigation levels. Differences in canopy temperature (<2 °C were measured between the two leaf shapes. As irrigation levels increased, canopy temperature differences between the leaf shapes declined. At the lowest irrigation level, when differences in sensible energy exchanges due to the okra leaf shape would be enhanced, the canopy temperature of the okra leaf was warmer than the normal leaf. This suggests that varietal differences that are not related to leaf shape may have more than compensated for leaf shape differences in the canopy temperature.

Herbivory mitigation through increased water-use efficiency in a leaf-mining moth-apple tree relationship.

Science.gov (United States)

Pincebourde, Sylvain; Frak, Ela; Sinoquet, Hervé; Regnard, Jean Luc; Casas, Jérôme

2006-12-01

Herbivory alters plant gas exchange but the effects depend on the type of leaf damage. In contrast to ectophagous insects, leaf miners, by living inside the leaf tissues, do not affect the integrity of the leaf surface. Thus, the effect of leaf miners on CO2 uptake and water-use efficiency by leaves remains unclear. We explored the impacts of the leaf-mining moth Phyllonorycter blancardella (Lepidoptera: Gracillariidae) on light responses of the apple leaf gas exchanges to determine the balance between the negative effects of reduced photosynthesis and potential positive impacts of increased water-use efficiency (WUE). Gas exchange in intact and mined leaf tissues was measured using an infrared gas analyser. The maximal assimilation rate was slightly reduced but the light response of net photosynthesis was not affected in mined leaf tissues. The transpiration rate was far more affected than the assimilation rate in the mine integument as a result of stomatal closure from moderate to high irradiance level. The WUE was about 200% higher in the mined leaf tissues than in intact leaf portions. Our results illustrate a novel mechanism by which plants might minimize losses from herbivore attacks; via trade-offs between the negative impacts on photosynthesis and the positive effects of increased WUE.

The relationship between leaf water status, gas exchange, and spectral reflectance in cotton leaves

Science.gov (United States)

Bowman, William D.

1989-01-01

Measurements of leaf spectral reflectance, the components of water potential, and leaf gas exchanges as a function of leaf water content were made to evaluate the use of NIR reflectance as an indicator of plant water status. Significant correlations were determined between spectral reflectance at 810 nm, 1665 nm, and 2210 nm and leaf relative water content, total water potential, and turgor pressure. However, the slopes of these relationships were relatively shallow and, when evaluated over the range of leaf water contents in which physiological activity occurs (e.g., photosynthesis), had lower r-squared values, and some relationships were not statistically significant. NIR reflectance varied primarily as a function of leaf water content, and not independently as a function of turgor pressure, which is a sensitive indicator of leaf water status. The limitations of this approach to measuring plant water stress are discussed.

Identification among morphologically similar Argyreia (Convolvulaceae) based on leaf anatomy and phenetic analyses.

Science.gov (United States)

Traiperm, Paweena; Chow, Janene; Nopun, Possathorn; Staples, G; Swangpol, Sasivimon C

2017-12-01

The genus Argyreia Lour. is one of the species-rich Asian genera in the family Convolvulaceae. Several species complexes were recognized in which taxon delimitation was imprecise, especially when examining herbarium materials without fully developed open flowers. The main goal of this study is to investigate and describe leaf anatomy for some morphologically similar Argyreia using epidermal peeling, leaf and petiole transverse sections, and scanning electron microscopy. Phenetic analyses including cluster analysis and principal component analysis were used to investigate the similarity of these morpho-types. Anatomical differences observed between the morpho-types include epidermal cell walls and the trichome types on the leaf epidermis. Additional differences in the leaf and petiole transverse sections include the epidermal cell shape of the adaxial leaf blade, the leaf margins, and the petiole transverse sectional outline. The phenogram from cluster analysis using the UPGMA method represented four groups with an R value of 0.87. Moreover, the important quantitative and qualitative leaf anatomical traits of the four groups were confirmed by the principal component analysis of the first two components. The results from phenetic analyses confirmed the anatomical differentiation between the morpho-types. Leaf anatomical features regarded as particularly informative for morpho-type differentiation can be used to supplement macro morphological identification.

Lateral Penumbra Modelling Based Leaf End Shape Optimization for Multileaf Collimator in Radiotherapy

Directory of Open Access Journals (Sweden)

Dong Zhou

2016-01-01

Full Text Available Lateral penumbra of multileaf collimator plays an important role in radiotherapy treatment planning. Growing evidence has revealed that, for a single-focused multileaf collimator, lateral penumbra width is leaf position dependent and largely attributed to the leaf end shape. In our study, an analytical method for leaf end induced lateral penumbra modelling is formulated using Tangent Secant Theory. Compared with Monte Carlo simulation and ray tracing algorithm, our model serves well the purpose of cost-efficient penumbra evaluation. Leaf ends represented in parametric forms of circular arc, elliptical arc, Bézier curve, and B-spline are implemented. With biobjective function of penumbra mean and variance introduced, genetic algorithm is carried out for approximating the Pareto frontier. Results show that for circular arc leaf end objective function is convex and convergence to optimal solution is guaranteed using gradient based iterative method. It is found that optimal leaf end in the shape of Bézier curve achieves minimal standard deviation, while using B-spline minimum of penumbra mean is obtained. For treatment modalities in clinical application, optimized leaf ends are in close agreement with actual shapes. Taken together, the method that we propose can provide insight into leaf end shape design of multileaf collimator.

Antimicrobial compounds from leaf extracts of Jatropha curcas, Psidium guajava, and Andrographis paniculata.

Science.gov (United States)

Rahman, M M; Ahmad, S H; Mohamed, M T M; Ab Rahman, M Z

2014-01-01

The present research was conducted to discover antimicrobial compounds in methanolic leaf extracts of Jatropha curcas and Andrographis paniculata and ethanolic leaf extract of Psidium guajava and the effectiveness against microbes on flower preservative solution of cut Mokara Red orchid flowers was evaluated. The leaves were analyzed using gas chromatography-mass spectrometry. A total of nine, 66, and 29 compounds were identified in J. curcas, P. guajava, and A. paniculata leaf extracts, with five (88.18%), four (34.66%), and three (50.47%) having unique antimicrobial compounds, respectively. The experimental design on vase life was conducted using a completely randomized design with 10 replications. The flower vase life was about 6 days in the solution containing the P. guajava and A. paniculata leaf extracts at 15 mg/L. Moreover, solution with leaf extracts of A. paniculata had the lowest bacterial count compared to P. guajava and J. curcas. Thus, these leaf extracts revealed the presence of relevant antimicrobial compounds. The leaf extracts have the potential as a cut flower solution to minimize microbial populations and extend flower vase life. However, the activities of specific antimicrobial compounds and double or triple combination leaf extracts to enhance the effectiveness to extend the vase life need to be tested.

Lateral Penumbra Modelling Based Leaf End Shape Optimization for Multileaf Collimator in Radiotherapy

Science.gov (United States)

Zhou, Dong; Zhang, Hui; Ye, Peiqing

2016-01-01