Pulsed laser deposition of SrRuO3 thin-films: The role of the pulse repetition rate

Directory of Open Access Journals (Sweden)

H. Schraknepper

2016-12-01

Full Text Available SrRuO3 thin-films were deposited with different pulse repetition rates, fdep, epitaxially on vicinal SrTiO3 substrates by means of pulsed laser deposition. The measurement of several physical properties (e.g., composition by means of X-ray photoelectron spectroscopy, the out-of-plane lattice parameter, the electric conductivity, and the Curie temperature consistently reveals that an increase in laser repetition rate results in an increase in ruthenium deficiency in the films. By the same token, it is shown that when using low repetition rates, approaching a nearly stoichiometric cation ratio in SrRuO3 becomes feasible. Based on these results, we propose a mechanism to explain the widely observed Ru deficiency of SrRuO3 thin-films. Our findings demand these theoretical considerations to be based on kinetic rather than widely employed thermodynamic arguments.

Highly efficient dual-wavelength mid-infrared CW Laser in diode end-pumped Er:SrF2 single crystals

Science.gov (United States)

Ma, Weiwei; Qian, Xiaobo; Wang, Jingya; Liu, Jingjing; Fan, Xiuwei; Liu, Jie; Su, Liangbi; Xu, Jun

2016-11-01

The spectral properties and laser performance of Er:SrF2 single crystals were investigated and compared with Er:CaF2. Er:SrF2 crystals have larger absorption cross-sections at the pumping wavelength, larger mid-infrared stimulated emission cross-sections and much longer fluorescence lifetimes of the upper laser level (Er3+:4I11/2 level) than those of Er:CaF2 crystals. Dual-wavelength continuous-wave (CW) lasers around 2.8 μm were demonstrated in both 4at.% and 10at.% Er:SrF2 single crystals under 972 nm laser diode (LD) end pumping. The laser wavelengths are 2789.3 nm and 2791.8 nm in the former, and 2786.4 nm and 2790.7 nm in the latter, respectively. The best laser performance has been demonstrated in lightly doped 4at.% Er:SrF2 with a low threshold of 0.100 W, a high slope efficiency of 22.0%, an maximum output power of 0.483 W.

Raman scattering spectra of superconducting Bi2Sr2CaCu2O8 single crystals

International Nuclear Information System (INIS)

Kirillov, D.; Bozovic, I.; Geballe, T.H.; Kapitulnik, A.; Mitzi, D.B.

1988-01-01

Raman spectra of Bi 2 Sr 2 CaCu 2 O 8 single crystals with superconducting phase-transition temperature of 90 K have been studied. The spectra contained phonon lines and electronic continuum. Phonon energies and polarization selection rules were measured. A gap in the electronic continuum spectrum was observed in a superconducting state. Noticeable similarity between Raman spectra of Bi 2 Sr 2 CaCu 2 O 8 and YBa 2 Cu 3 O 7 was found

Raman scattering spectra of superconducting Bi2Sr2CaCu2O8 single crystals

Science.gov (United States)

Kirillov, D.; Bozovic, I.; Geballe, T. H.; Kapitulnik, A.; Mitzi, D. B.

1988-12-01

Raman spectra of Bi2Sr2CaCu2O8 single crystals with superconducting phase-transition temperature of 90 K have been studied. The spectra contained phonon lines and electronic continuum. Phonon energies and polarization selection rules were measured. A gap in the electronic continuum spectrum was observed in a superconducting state. Noticeable similarity between Raman spectra of Bi2Sr2CaCu2O8 and YBa2Cu3O7 was found.

Synthesis of BiFeO3 thin films on single-terminated Nb : SrTiO3 (111 substrates by intermittent microwave assisted hydrothermal method

Directory of Open Access Journals (Sweden)

Ivan Velasco-Davalos

2016-06-01

Full Text Available We report on a simple and fast procedure to create arrays of atomically flat terraces on single crystal SrTiO3 (111 substrates and the deposition of ferroelectric BiFeO3 thin films on such single-terminated surfaces. A microwave-assisted hydrothermal method in deionized water and ammonia solution selectively removes either (SrO34− or Ti4+ layers to ensure the same chemical termination on all terraces. Measured step heights of 0.225 nm (d111 and uniform contrast in the phase image of the terraces confirm the single termination in pure and Nb doped SrTiO3 single crystal substrates. Multiferroic BiFeO3 thin films were then deposited by the same microwave assisted hydrothermal process on Nb : SrTiO3 (111 substrates. Bi(NO33 and Fe(NO33 along with KOH served as the precursors solution. Ferroelectric behavior of the BiFeO3 films on Nb : SrTiO3 (100 substrates was verified by piezoresponse force microscopy.

High colour purity single-phased full colour emitting white LED phosphor Sr2V2O7:Eu3+

International Nuclear Information System (INIS)

Zhou Zhi; Zhou Nan; He Zhangxing; Liu Suqin; Liu Younian; Tian Ziwei; Wang Nanfang; Mao Zhiyong; Hintzen, H T

2013-01-01

Single-phased white-light-emitting phosphor Sr 2 V 2 O 7 :Eu 3+ was successfully synthesized by the solid-state method. The result of x-ray diffraction analysis indicated that the obtained phosphor has the same crystal structure as that of Sr 2 V 2 O 7 . The synthesized Sr 2 V 2 O 7 :Eu 3+ was combined with near-UV light (365 nm) chips and then assembled into ligtht-emitting diodes (LED) devices, which generated white light with colour coordinates of (0.324, 0.317). The white light was generated from yellow-green and red emissions, which should be attributed to the host Sr 2 V 2 O 7 and dopant Eu ions, respectively. The effects of the concentration of Eu ions and charge compensation on the emission intensity were carefully investigated. The results show that the energy migrates from the host to the dopant and also that Li 2 CO 3 should be the best charge compensator for this single-phased phosphor. In addition, the colour rendering index and luminescence efficiency of the fabricated LED devices with Sr 1.90 V 2 O 7 :0.10Eu 3+ phosphor were 91 and 32 lm W -1 , respectively, suggesting that Sr 1.90 V 2 O 7 :0.10Eu 3+ phosphor is a potential candidate for the phosphor-converted white-light-emitting diodes with near-UV chips.

Geochronological synthesis of Bahia state and the crustal evolution, based in evolution diagram of Sr and initial rate of Sr87/Sr86

International Nuclear Information System (INIS)

Sato, K.

1986-01-01

The crustal evolution of the ancient terrains of the State of Bahia, Brazil, is attempted with the aid of Sr isotopic results as natural tracers. Some Nd and Pb isotopic data are also available, and support the main conclusions based on Sr evolution diagrams. The analysis of the Sr evolution diagrams shows that the Archean Terrains are mainly formed by accretion from mantle-derived material, but crustal reworking is indicated by the high initial 87 Sr/ 86 Sr value of the Jequie Complex. The Transamazonian mobile belt include both types of materials, but the 87 Sr/ 86 Sr value, generally lower than those of the Jequie Complex, markes improbable a direct derivation. During Middle and Late Proterozoic, the continental crust was already well consolidated, and reworking of crustal material predominated within the Espinhaco and Brasiliano folded systems [pt

Single Crystal Growth of Pure Co3+ Oxidation State Material LaSrCoO4

Directory of Open Access Journals (Sweden)

Hanjie Guo

2016-08-01

Full Text Available We report on the single crystal growth of the single-layer perovskite cobaltate LaSrCoO4 that was grown by the optical floating zone method using high oxygen pressures. Phase purity and single crystallinity were confirmed by X-ray diffraction techniques. The pure Co3+ oxidation state was confirmed by X-ray absorbtion spectroscopy measurements. A transition to a spin glass state is observed at ∼7 K in magnetic susceptibility and specific heat measurements.

Superconductivity in SrNi2P2 single crystals

Energy Technology Data Exchange (ETDEWEB)

Ronning, Filip [Los Alamos National Laboratory; Bauer, Eric D [Los Alamos National Laboratory; Park, Tuscon [Los Alamos National Laboratory; Thompson, Joe D [Los Alamos National Laboratory

2009-01-01

Heat capacity, magnetic susceptibility, and resistivity of SrNi{sub 2}P{sub 2} single crystals are presented, illustrating the structural transition at 325 K, and bulk superconductivity at 1.4 K. The magnitude of {Tc}, fits to the heat capacity data, the small upper critical field H{sub c2} = 390 Oe, and {kappa} = 2.1 suggests a conventional fully gapped superconductor. With applied pressure we find that superconductivity persists into the so-called 'collapsed tetragonal' phase, although the transition temperature is monotonically suppressed with increasing pressure. This argues that reduced dimensionality can be a mechanism for increasing the transition temperatures of layered NiP, as well as layered FeAs and NiAs, superconductors.

Neodymium-doped Sr5(PO4)3F and Sr5(VO4)3F

International Nuclear Information System (INIS)

Corker, D.L.; Nicholls, J.; Loutts, G.B.

1995-01-01

Neodymium-doped Sr 5 (PO 4 ) 3 F [neodymium strontium fluoride phosphate, (Nd,Sr) 5 (PO 4 ) 3 F] and neodymium-doped Sr 5 (VO 4 ) 3 F [neodymium strontium fluoride vanadate, (Nd,Sr) 5 (VO 4 ) 3 F] crystallize in space group P6 3 /m and are isostructural with calcium fluorophosphate, Ca 5 (PO 4 ) 3 F. There are two different Sr sites in Sr 5 (XO 4 ) 3 F, denoted Sr(1) and Sr(2). Using single-crystal X-ray diffraction the two structures were refined to R factors of 2.3 and 2.2%, respectively, showing that Nd is present at both Sr sites in (Sr,Nd) 5 (VO 4 ) 3 F but only at the Sr(2) site in (Sr,Nd) 5 (PO 4 ) 3 F. (orig.)

Superconductivity and electronic structure in single-layer FeSe on SrTiO{sub 3} probed by scanning tunneling microscopy

Energy Technology Data Exchange (ETDEWEB)

Jandke, Jasmin; Dressner, Jonas; Wulfhekel, Wulf [Physikalisches Institut, Karlsruhe Institute of Technology (Germany); Yang, Fang; Gao, Chunlei [Fudan Universitaet, Shanghai (China)

2016-07-01

We use high-resolution scanning tunneling spectroscopy (STS) to study single-layer FeSe on Nb-doped SrTiO{sub 3} (001). Features of bosonic excitations were observed in the measured quasiparticle density of states. Furthermore, using STS, quasiparticle interference (QPI) imaging was performed in order to map the multiband electronic structure of FeSe. Compared to previous measurements, an additional feature is visible in our measured QPI maps on a single-layer FeSe/SrTiO{sub 3}. The origin of this feature will be discussed.

Experiences with the determination of Sr-89 and Sr-90 using fast methods; Erfahrungen bei der Bestimmung von {sup 89}Sr und {sup 90}Sr mittels Schnellmethoden

Energy Technology Data Exchange (ETDEWEB)

Kowalik, C.; Fueger, J. [Thueringer Landesanstalt fuer Umwelt und Geologie, Jena (Germany). Landesmessstelle fuer Umweltradioaktivaet

2014-01-20

Quick methods of the measurement of {sup 89}Sr and {sup 90}Sr have a great importance in the supervision of the environmental radioactivity. It is necessary to receive in short time dependable analytical data to be able to carry out suitable assessments or to give recommendations. The aim of the investigations was to be guaranteed the demands for these methods (test preparation, measurement and evaluation). The use of the solid phase extraction by means of commercial Sr Resin trademark columns (4.4' (5')-Di-tert-butylcyclohexanol-18-kronen-6-aether) (Triskem) to the radiochemical separation of the Sr isotopes was suitable. The measurements occurred to the FHT 770 T12 - Multi Low Level Alpha/Beta Sample Counter (Thermo Scientific). The results contain the summary activities of all available Sr isotopes, as for example {sup 89}Sr and {sup 90}Sr. The calculations of the single activities occur about the mathematical algorithm of the linear development on the basis of the works of G. Kanisch. The first results show, this method is suitable for the analysis of {sup 89}Sr and {sup 90}Sr and is used therefore in future in Thuringia.

Synthesis of BiFeO{sub 3} thin films on single-terminated Nb : SrTiO{sub 3} (111) substrates by intermittent microwave assisted hydrothermal method

Energy Technology Data Exchange (ETDEWEB)

Velasco-Davalos, Ivan; Ambriz-Vargas, Fabian; Kolhatkar, Gitanjali; Thomas, Reji, E-mail: ruediger@emt.inrs.ca, E-mail: reji.thomas@emt.inrs.ca; Ruediger, Andreas, E-mail: ruediger@emt.inrs.ca, E-mail: reji.thomas@emt.inrs.ca [Centre Énergie, Matériaux et Télécommunications, INRS, 1650 Lionel-Boulet, Varennes, Québec, J3X1S2 (Canada)

2016-06-15

We report on a simple and fast procedure to create arrays of atomically flat terraces on single crystal SrTiO{sub 3} (111) substrates and the deposition of ferroelectric BiFeO{sub 3} thin films on such single-terminated surfaces. A microwave-assisted hydrothermal method in deionized water and ammonia solution selectively removes either (SrO{sub 3}){sup 4−} or Ti{sup 4+} layers to ensure the same chemical termination on all terraces. Measured step heights of 0.225 nm (d{sub 111}) and uniform contrast in the phase image of the terraces confirm the single termination in pure and Nb doped SrTiO{sub 3} single crystal substrates. Multiferroic BiFeO{sub 3} thin films were then deposited by the same microwave assisted hydrothermal process on Nb : SrTiO{sub 3} (111) substrates. Bi(NO{sub 3}){sub 3} and Fe(NO{sub 3}){sub 3} along with KOH served as the precursors solution. Ferroelectric behavior of the BiFeO{sub 3} films on Nb : SrTiO{sub 3} (100) substrates was verified by piezoresponse force microscopy.

NMR studies of spin excitations in superconducting Bi2Sr2CaCu2O8+δ single crystals

Science.gov (United States)

Takigawa, M.; Mitzi, D. B.

1994-08-01

The oxygen NMR shift and the Cu nuclear spin-lattice relaxation rate (1/T1) were measured in Bi2.1Sr1.9Ca0.9Cu2.1O8+δ single crystals. While both the shift and 1/(T1T) decrease sharply near Tc, 1/(T1T) becomes nearly constant at low temperatures, indicating a gapless superconducting state with finite density of states at the Fermi level. From the oxygen shift data, the residual spin susceptibility at T=0 is estimated to be 10% of the value at room temperature. Our results are most consistent with a d-wave pairing model with strong (resonant) impurity scattering.

Factor structure, reliability, and validity of the Japanese version of the Hoarding Rating Scale-Self-Report (HRS-SR-J

Directory of Open Access Journals (Sweden)

Tsuchiyagaito A

2017-05-01

Full Text Available Aki Tsuchiyagaito,1–3 Satoshi Horiuchi,4 Toko Igarashi,5 Yoshiya Kawanori,4 Yoshiyuki Hirano,1,3 Hirooki Yabe,2 Akiko Nakagawa1,3 1Research Center for Child Mental Development, Chiba University, Chiba, 2Department of Neuropsychiatry, Fukushima Medical University, Fukushima, 3United Graduate School of Child Development, Osaka University, Kanazawa University, Hamamatsu University School of Medicine, Chiba University and University of Fukui, Osaka, 4Faculty of Social Welfare, Iwate Prefectural University, Iwate, 5Graduate School of Education, Joetsu University of Education, Niigata, Japan Background: The Hoarding Rating Scale-Self-Report (HRS-SR is a five-item scale that assesses the symptoms of hoarding. These symptoms include excessive acquisition, difficulty in discarding, and excessive clutter that causes distress. We conducted three studies to examine the factor structure, reliability, and validity of the Japanese version of the HRS-SR (HRS-SR-J. Methods: Study 1 examined its reliability; 193 college students and 320 adolescents and adults completed the HRS-SR-J and, of the college students, 32 took it again 2 weeks later. Study 2 aimed to confirm that its scores in a sample of 210 adolescents and adults are independent of social desirability. Study 3 aimed to validate the HRS-SR-J in the aspects of convergent and discriminant validity in a sample of 550 adults. Results: The HRS-SR-J showed good internal consistency and 2-week test–retest reliability. Based on the nonsignificant correlations between the HRS-SR-J and social desirability, the HRS-SR-J was not strongly affected by social desirability. In addition, it also had a good convergent validity with the Japanese version of the Saving Inventory-Revised (SI-R-J and the hoarding subscale of the Obsessive-Compulsive Inventory, while having a significantly weaker correlation with the five subscales of the Obsessive-Compulsive Inventory, except for the hoarding subscale. In addition, the

Laser excited fluorescence spectrum of Ho3+:SrF2 single crystal

International Nuclear Information System (INIS)

Lal, Bansi; Ramachandra Rao, D.

1980-01-01

The fluorescence spectrum of Ho 3+ : SrF 2 single crystal excited by the various lines of an Ar + laser, is reported. The three fluorescence groups recorded in the region 5300-7700 A, correspond to the transitions from ( 5 F 4 , 5 S 2 ) to 5 I 8 , 5 F 5 to 5 I 8 , 5 F 3 to 5 I 7 and ( 5 F 4 , 5 S 2 ) to 5 I 7 . Marked changes in the total integrated intensity of the various fluorescence groups with the change in the exciting wavelength are observed. (author)

Large piezoelectricity in electric-field modified single crystals of SrTiO3

Science.gov (United States)

Khanbabaee, B.; Mehner, E.; Richter, C.; Hanzig, J.; Zschornak, M.; Pietsch, U.; Stöcker, H.; Leisegang, T.; Meyer, D. C.; Gorfman, S.

2016-11-01

Defect engineering is an effective and powerful tool to control the existing material properties and produce completely new ones, which are symmetry-forbidden in a defect-free crystal. For example, the application of a static electric field to a single crystal of SrTiO3 forms a strained near-surface layer through the migration of oxygen vacancies out of the area beneath the positively charged electrode. While it was previously shown that this near-surface phase holds pyroelectric properties, which are symmetry-forbidden in centrosymmetric bulk SrTiO3, this paper reports that the same phase is strongly piezoelectric. We demonstrate the piezoelectricity of this phase through stroboscopic time-resolved X-ray diffraction under alternating electric field and show that the effective piezoelectric coefficient d33 ranges between 60 and 100 pC/N. The possible atomistic origins of the piezoelectric activity are discussed as a coupling between the electrostrictive effect and spontaneous polarization of this near-surface phase.

Electronic structure and lattice dynamics at the interface of single layer FeSe and SrTiO3

Science.gov (United States)

Ahmed, Towfiq; Balatsky, Alexander; Zhu, Jian-Xin

Recent discovery of high-temperature superconductivity with the superconducting energy gap opening at temperatures close to or above the liquid nitrogen boiling point in the single-layer FeSe grown on SrTiO3 has attracted significant interest. It suggests that the interface effects can be utilized to enhance the superconductivity. It has been shown recently that the coupling between the electrons in FeSe and vibrational modes at the interface play an important role. Here we report on a detailed study of electronic structure and lattice dynamics in the single-layer FeSe/SrTiO3 interface by using the state-of-art electronic structure method within the density functional theory. The nature of the vibrational modes at the interface and their coupling to the electronic degrees of freedom are analyzed. In addition, the effect of hole and electron doping in SrTiO3 on the electron-mode coupling strength is also considered. This work was carried out under the auspices of the National Nuclear Security Administration of the U.S. DOE at LANL under Contract No. DE-AC52-06NA25396, and was supported by the DOE Office of Basic Energy Sciences.

Cortical bone resorption rate in elderly persons: Estimates from long-term in vivo measurements of 90Sr in the skeleton

Energy Technology Data Exchange (ETDEWEB)

Shagina, N. B.; Tolstykh, E. I.; Degteva, M. O.; Anspaugh, L. R.; Napier, Bruce A.

2012-06-01

The rate of cortical bone resorption was assessed from long-term in vivo measurements of 90Sr content in the skeleton for men aged 50-80 years and for women 0-30 years after menopause. Measurements of 90Sr were conducted with a whole body counter for residents of the Techa Riverside communities (Southern Urals, Russia), who ingested large amounts of 90Sr as a result of releases of liquid radioactive wastes into the river from the Mayak plutonium facility in early 1950s. The results of this study showed an increase in the rate of cortical bone resorption in both men and women, as based on the use of accidentally ingested 90Sr as a tracer for bone metabolism. In men there was a continuous gradual increase in the rate of cortical bone resorption after 55 years from 2.8 to 4.5%/year by the age of 75 years. In women, there was a doubled increase in the rate of cortical bone resorption after menopause of up to 6%/year; then the rate remained unchanged for 10-12 years with a subsequent gradual decline down to 5-5.5%/year. Comparison of the rate of cortical bone resorption in men and women older than 55 years showed that women expressed significantly higher levels of cortical bone resorption.

Cortical bone resorption rate in elderly persons: Estimates from long-term in vivo measurements of 90Sr in the skeleton

International Nuclear Information System (INIS)

Shagina, N.B.; Tolstykh, E.I.; Degteva, M.O.; Anspaugh, L.R.; Napier, Bruce A.

2012-01-01

The rate of cortical bone resorption was assessed from long-term in vivo measurements of 90Sr content in the skeleton for men aged 50-80 years and for women 0-30 years after menopause. Measurements of 90Sr were conducted with a whole body counter for residents of the Techa Riverside communities (Southern Urals, Russia), who ingested large amounts of 90Sr as a result of releases of liquid radioactive wastes into the river from the Mayak plutonium facility in early 1950s. The results of this study showed an increase in the rate of cortical bone resorption in both men and women, as based on the use of accidentally ingested 90Sr as a tracer for bone metabolism. In men there was a continuous gradual increase in the rate of cortical bone resorption after 55 years from 2.8 to 4.5%/year by the age of 75 years. In women, there was a doubled increase in the rate of cortical bone resorption after menopause of up to 6%/year; then the rate remained unchanged for 10-12 years with a subsequent gradual decline down to 5-5.5%/year. Comparison of the rate of cortical bone resorption in men and women older than 55 years showed that women expressed significantly higher levels of cortical bone resorption.

Test of 134Cs, 85,89Sr leaching rate in a resemble vitrifiable cement waste form

International Nuclear Information System (INIS)

Lin Meiqiong; Wei Feng; Yin Qi; Fan Xianhua; Xu Shengli; Li Yongde

2003-01-01

A novel material--resemble vitrifiable cement for conditioning low and mediate level radioactive waste has been developed. Waste form has been characterized for their physical and chemical performance, phase composition. The cement formulation has been patented. In this experiment the cement is mixed with simulated wastes spiked with 134 Cs and 85,89 Sr by 5 min at least. The Ratio of the waste to the cement is 0.45-0.55. The mixture is packed into cylindrical molds which has the same dimension of diameter and height . The grouts are cured for a period of 28 d in a room temperature curing chamber at an atmospheric pressure. The cured waste form is then completely immersed into deionized water. According to standard GB7023-86, leaching rate of 134 Cs and 85,89 Sr are measured. The result shows that the leaching rate of the species 134 Cs and 85,89 Sr is to be on the order 10 -4 and 10 -5 on the 42 d immersion, respectively and is better than that of commercial cement

Ab initio study of the positronation of the CaO and SrO molecules including calculation of annihilation rates.

Science.gov (United States)

Buenker, Robert J; Liebermann, Heinz-Peter

2012-07-15

Ab initio multireference single- and double-excitation configuration interaction calculations have been performed to compute potential curves for ground and excited states of the CaO and SrO molecules and their positronic complexes, e(+)CaO, and e(+)SrO. The adiabatic dissociation limit for the (2)Σ(+) lowest states of the latter systems consists of the positive metal ion ground state (M(+)) and the OPs complex (e(+)O(-)), although the lowest energy limit is thought to be e(+)M + O. Good agreement is found between the calculated and experimental spectroscopic constants for the neutral diatomics wherever available. The positron affinity of the closed-shell X (1)Σ(+) ground states of both systems is found to lie in the 0.16-0.19 eV range, less than half the corresponding values for the lighter members of the alkaline earth monoxide series, BeO and MgO. Annihilation rates (ARs) have been calculated for all four positronated systems for the first time. The variation with bond distance is generally similar to what has been found earlier for the alkali monoxide series of positronic complexes, falling off gradually from the OPs AR value at their respective dissociation limits. The e(+)SrO system shows some exceptional behavior, however, with its AR value reaching a minimum at a relatively large bond distance and then rising to more than twice the OPs value close to its equilibrium distance. Copyright © 2012 Wiley Periodicals, Inc.

Weak interaction rates for Kr and Sr waiting-point nuclei under rp-process conditions

International Nuclear Information System (INIS)

Sarriguren, P.

2009-01-01

Weak interaction rates are studied in neutron deficient Kr and Sr waiting-point isotopes in ranges of densities and temperatures relevant for the rp process. The nuclear structure is described within a microscopic model (deformed QRPA) that reproduces not only the half-lives but also the Gamow-Teller strength distributions recently measured. The various sensitivities of the decay rates to both density and temperature are discussed. Continuum electron capture is shown to contribute significantly to the weak rates at rp-process conditions.

Thickness-dependent photovoltaic effects in miscut Nb-doped SrTiO3 single crystals

International Nuclear Information System (INIS)

Yue Zengji; Zhao Kun; Zhao Songqing; Lu Zhiqing; Li Xiaoming; Ni Hao; Wang Aijun

2010-01-01

The photovoltaic effects of Nb-doped SrTiO 3 single crystals with different thicknesses were investigated under the illumination of ultraviolet pulsed lasers. The peak photovoltage increased and then decreased quickly with the decrease in crystal thickness, and a maximum photovoltage occurred for the 180 μm-thick crystal. The photovoltaic response time decreased monotonically with decreasing crystal thickness. The present results suggested the promising potential of reducing crystal thickness in high sensitivity detectors with fast response.

Single crystal neutron diffraction study of SrFeOsub(3-x)(x=0. 1)

Energy Technology Data Exchange (ETDEWEB)

Oda, H; Yamaguchi, Y; Takei, H; Watanabe, H [Tohoku Univ., Sendai (Japan). Research Inst. for Iron, Steel and Other Metals

1977-01-01

Neutron diffraction study was carried out on single crystals of the perovskite oxide SrFeOsub(3-x)(x=0.1). SrFeOsub(3-x)(x=0.1) has a proper screw spin structure with the propagation vector parallel to (111) direction and its Neel temperature is 118 K. The electron configuration of Fe/sup 4 +/(3d/sup 4/) ion is close to the low-spin state (tsub(2g)sup(4)) and the oxygen ion has the unpaired electron with the magnetic moment of 0.3..mu..sub(B) antiparallel to the vector sum of the magnetic moments of two iron ions lying on the neighbouring planes perpendicular to the screw axis. The absolute value of the propagation vector is almost constant. 0.130x..sqrt..3.2..pi../a A/sup -1/, at temperatures below 50 K, while it decreases gradually at higher temperatures reaching 0.118x..sqrt..3.2..pi../a A/sup -1/ at Tsub(N).

Synthesis, single crystal growth and thermodynamic properties of SrNdAlO4-CaNdAlO4 solid solutions

International Nuclear Information System (INIS)

Novoselov, A.; Ryumin, M.; Pushkina, G.; Spiridonov, F.; Komissarova, L.; Zimina, G.; Pajaczkowska, A.

2005-01-01

Continuous solid solutions in the SrNdAlO 4 -CaNdAlO 4 system are formed. Powder samples of Sr x Ca 1-x NdAlO 4 (0.0≤x≤1.0) were obtained using the carbonate coprecipitation method while single crystals of Sr x Ca 1-x NdAlO 4 (x=0.0,0.162,0.392,0.687,1.0) were grown by the Czochralski method. Structural parameters and thermodynamic properties of the samples were studied by X-ray diffraction and heat flux Calvet calorimetry. Composition dependence of lattice constants was observed to follow Vegard's low. Heat of solution of the Sr x Ca 1-x NdAlO 4 samples in molten 2PbO.B 2 O 3 were measured, and enthalpies of formation and mixing were calculated. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

The rate of 99m Tc-MDP uptake in metastatic bone lesions before and after 89m Sr therapy

International Nuclear Information System (INIS)

Souza, Joseane Fonseca; Braga, Francisco J.H.N.

1996-01-01

The rate of 99m Tc-MDP uptake is studied in metastatic bone lesions, before and after 89m Sr therapy. Eight hopeless patients (age between 56 and 74) presenting disseminated carcinoma of the prostate are evaluated. No hormonal therapy and a limited radiotherapy were considered. It is concluded that therapeutical doses of 89m Sr reduces MDP uptake

Addition and spin exchange rate constants by longitudinal field μSR: the Mu + NO reaction

International Nuclear Information System (INIS)

Senba, Masayoshi; Gonzalez, A.C.; Kempton, J.R.; Arseneau, D.J.; Pan, J.J.; Tempelmann, A.; Fleming, D.G.

1991-01-01

The addition reaction Mu + NO + M → MuNO + M and the spin exchange reaction Mu(↑) + NO(↓)→Mu(↓)+NO(↑) have been measured by longitudinal field μSR at room temperature in the presence of up to 58 atm of N 2 as inert collider. The pressure dependence of the longitudinal relaxation rate due to the addition reaction (λ c ) demonstrates that the system is still in the low pressure regime in this pressure range. The corresponding termolecular rate constant has been determined as k 0.Mu =(1.10±0.25)x10 -32 cm 6 molecules -2 s -1 , almost 4 times smaller than the corresponding H atom reaction k 0,H =3.90x10 -32 cm 6 molecules -2 s -1 . The average value of the spin exchange rate constants in the 2.5-58 atm pressure range, k SE = (3.16±0.06)x10 -10 cm 3 molecule -1 s -1 , is in good agreement with previous values obtained by transverse field μSR. (orig.)

Single-phased white-light-emitting Sr3NaLa(PO4)3F: Eu2+,Mn2+ phosphor via energy transfer

International Nuclear Information System (INIS)

Shanshan, Hu; Wanjun, Tang

2014-01-01

Single-phased white-light-emitting Sr 3 NaLa(PO 4 ) 3 F:Eu 2+ ,Mn 2+ phosphor is synthesized via the combustion-assisted synthesis technique. Upon excitation of 344 nm ultraviolet (UV) light, two intense broad bands have clearly been obtained due to the allowed 5d–4f transition of Eu 2+ and the forbidden 4 T 1 − 6 A 1 transition of Mn 2+ , respectively. As a result of fine-tuning of the emission composition of the Eu 2+ and Mn 2+ ions, white-light emission can be realized by combining the emission of Eu 2+ and Mn 2+ in a single host lattice under UV light excitation. The obtained phosphor exhibits a strong excitation band between 250 and 420 nm, matching well with the dominant emission band of a UV light-emitting-diode (LED) chip, which could be a promising candidate for UV-converting white-light-emitting diodes (LEDs). -- Highlights: • Single-phased Sr 3 NaLa(PO 4 ) 3 F:Eu 2+ ,Mn 2+ phosphors are synthesized. • Sr 3 NaLa(PO 4 ) 3 F:Eu 2+ ,Mn 2+ shows a blue emission band and a yellow emission band. • White-emitting can be obtained by tuning the compositions of the Eu 2+ and Mn 2+

Morphology of growth of Bi2Sr2CaCu2O8 single crystals

Science.gov (United States)

Indenbom, M. V.; van der Beek, C. J.; Berseth, V.; Wolf, Th.; Berger, H.; Benoit, W.

1996-12-01

A good correlation of twins on the basal surface of flux-grown Bi2Sr2CaCu2Ox (BSCCO) single crystals with surface. growth steps is observed, the b-axis being perpendicular to the steps and, thus, parallel to the growth direction. It is found that mono-twin BSCCO single crystals produced by the travelling solvent floating zone method also grow preferentially along b, i.e. nearly perpendicularly to the boule axis, contrary to the common belief. This new understanding of the morphology of growth explains the nature of major defects in these crystals, which considerably change their measured superconducting properties, in a different way.

Bi sub 2 Sr sub 2 Ca sub n sub - sub 1 Cu sub n O sub y films sputtered on substrates of Bi sub 2 Sr sub 2 CuO sub y single crystals

CERN Document Server

Katsurahara, K; Matsumoto, K; Fujiwara, N; Tanaka, H; Kishida, S

2003-01-01

We prepared Bi sub 2 Sr sub 2 CaCu sub 2 O sub y (Bi-2212) films on substrates of Bi sub 2 Sr sub 2 CuO sub y (Bi-2201) single crystals by a rf magnetron sputtering method, where He and O sub 2 mixture sputtering gas and an off-axis geometry were used. The EPMA measurement indicated that the films deposited on the Bi-2201 single crystal had approximately the same composition as those on MgO substrate, which showed a Bi-221 single-phase. The film deposited on the Bi-2201 single crystal post-annealed at 500degC for 0.5h showed a metallic temperature dependent resistance in the normal state and the superconducting transition (T sub c sup o sup n sup s sup e sup t) of about 80 K. Therefore, the Bi-2212 films are considerate to grow on the substrate of the Bi-2201 singe crystal. (author)

Electronic structure of single crystalline Bi2(Sr,Ca,La)3Cu2O8

International Nuclear Information System (INIS)

Lindberg, P.A.P.; Shen, Z.X.; Dessau, D.S.; Wells, B.O.; Borg, A.; Mitzi, D.B.; Lindau, I.; Spicer, W.E.; Kapitulnik, A.

1989-01-01

Angle-resolved photoemission experiments on single crystals of Bi 2 (Sr,Ca,La) 3 Cu 2 O 8 are reported. The data show a dispersionless behavior of the valence band states as a function of the perpendicular component of the wave vector (along the c-axis), while as a function of the parallel component (in the a-b plane) clear dispersion occurs. Furthermore, polarization-dependent excitations reveal information on the symmetry of the unoccupied states

Modification of SrTiO3 single-crystalline surface after plasma flow treatment

Energy Technology Data Exchange (ETDEWEB)

Levin, Alexandr A.; Weissbach, Torsten; Leisegang, Tilmann; Meyer, Dirk C. [Institut fuer Strukturphysik, Technische Universitaet Dresden, 01062 Dresden (Germany); Kulagin, Nikolay A. [Kharkiv National University for Radioelectronics, av. Shakespeare 6-48, 61045 Kharkiv (Ukraine); Langer, Enrico [Institut fuer Festkoerperphysik, Technische Universitaet Dresden, 01062 Dresden (Germany)

2009-07-01

Surface of pure and transition metal-doped SrTiO3(STO) single crystals before and after hydrogen plasma-flow treatment (energy of 5..20 J/cm2) is investigated by wide-angle X-ray diffraction (WAXRD), fluorescence X-ray absorption near edge structure (XANES) and scanning electron microscopy (SEM) techniques. Plasma treatment results in the formation of a textured polycrystalline layer at the surface of the single-crystalline samples with different orientation. The formation of the quasi-ordered structures consisting of nanoscale-sized pyramids is observed by SEM. XANES evidences the change of the valency of the part of Ti4+ to Ti3+ due to the plasma treatment. The data obtained together with results of X-ray spectroscopy measurements gives evidences of the change of stoichiometry of the STO samples resulting in a change of their physical properties after plasma treatment.

Possible two-stage 87Sr evolution in the Stockdale Rhyolite

International Nuclear Information System (INIS)

Compston, W.; McDougall, I.; Wyborn, D.

1982-01-01

The Rb-Sr total-rock data for the Stockdale Rhyolite, of significance for the Palaeozoic time scale, are more scattered about a single-stage isochron than expected from experimental error. Two-stage 87 Sr evolution for several of the samples is explored to explain this, as an alternative to variation in the initial 87 Sr/ 86 Sr which is customarily used in single-stage dating models. The deletion of certain samples having very high Rb/Sr removes most of the excess scatter and leads to an estimate of 430 +- 7 m.y. for the age of extrusion. There is a younger alignment of Rb-Sr data within each sampling site at 412 +- 7 m.y. We suggest that the Stockdale Rhyolite is at least 430 m.y. old, that its original range in Rb/Sr was smaller than now observed, and that it experienced a net loss in Sr during later hydrothermal alteration at ca. 412 m.y. (orig.)

Preparation and crystal structure of SrCu/sub 2/Sb/sub 2/ and SrZnBi/sub 2/

Energy Technology Data Exchange (ETDEWEB)

Cordier, G; Eisenmann, B; Schaefer, H [Technische Hochschule Darmstadt (Germany, F.R.). Fachbereich Anorganische Chemie und Kernchemie

1976-10-01

SrCu/sub 2/Sb/sub 2/ and SrZnBi/sub 2/ have been prepared and analytically and structurally characterized. SrCu/sub 2/Sb/sub 2/ crystallizes tetragonal in the CaBe/sub 2/Ge/sub 2/ structure type. SrZnBi/sub 2/ has its own structure type. In both structures the transition metal atoms form with the semimetal atoms tetragonal pyramids, which are connected by common edges of the basis to twodimensional sheets. These sheets are separated in the case of SrCu/sub 2/Sb/sub 2/ by single sheets of strontium atoms, in the case of SrZnBi/sub 2/ by double sheets of strontium atoms in which fourfold nets of Bi atoms are located.

Optical properties of SrTiO3 films

International Nuclear Information System (INIS)

Agasiyev, A.A.; Magerramov, E.M.; Mammadov, M.Z.; Sarmasov, S.M.

2010-01-01

The spectrums of optical absorption of amorphous and single crystalline films SrTiO 3 at temperatures : 105 K, 300 K, 400 K are investigated. The temperature dependences of slope absorption edge, forbidden gap and characteristic constant of Urbah rule are obtained. The forbidden gap of single crystalline film SrTiO 3 and average shift shift of absorption edge degree are defined. It is established that edge of optical absorption of SrTiO 3 film is obeyed to Urbah rule and the absorption in the investigated region is caused by the transition of electron interacting with phonon

TL characterization of Ag co-doped SrSO{sub 4}:Eu phosphor for gamma dosimetry applications

Energy Technology Data Exchange (ETDEWEB)

Jayasudha, S., E-mail: jsnair.india@gmail.com [Mahatma Gandhi College, Pattom Palace P.O., Thiruvananthapuram 695004 (India); Madhukumar, K.; Nair, C.M.K.; Nair, Resmi G.; Anandakumar, V.M. [Mahatma Gandhi College, Pattom Palace P.O., Thiruvananthapuram 695004 (India); Elias, T.S. [State Institute of Cancer Research, Medical College P.O., Thiruvananthapuram 695011 (India); Rajesh, S. [Campus Universitario de Santiago, Aveiro (Portugal)

2017-04-15

High temperature thermoluminescence (TL) emissions and improvement in fading due to the co-doping ofr Ag in the SrSO{sub 4}:Eu phosphor synthesized through chemical precipitation technique when subjected to γ-excitation is discussed. The dopant concentrations were tuned for optimum TL sensitivity. Preliminary crystallographic and structural studies of the phosphors were done using PXRD, SEM, and TEM. The phosphor has a single phase orthorhombic lattice structure and the crystallites are found to be nanostructured. The presence of dopants in the host matrix is established through EDS and ICP-AES studies. The TL glow curve shows a single intense emission at 314 ├ó┬ü┬░C under γ- exposure of dose 1 Gy, which is given from a {sup 60}Co build-up. The dosimetric properties such as sensitivity, dose dependence, fading and reusability of SrSO{sub 4}:Eu,Ag phosphor were also studied. It is observed that co-doping with Ag improves the fading rate of the SrSO{sub 4}:Eu phosphor by about 5%. Even though the luminescence intensity is found to be less than that of SrSO{sub 4}:Eu phosphor, the Ag co-doped phosphor becomes significant owing to its improved fading rate and high temperature afterglow. The gamma sensitivity of the SrSO{sub 4}:Eu,Ag(0.5,0.5 mol%) phosphor is compared to that of the standard CaSO{sub 4}:Dy TLD phosphor. The TL kinetic parameters were calculated using IR, Chen's peak shape method and verified by the theoretical fit using GCD functions. - Highlights: • A High temperature TL emission is observed for the SrSO{sub 4}:Eu,Ag phosphor. • TL intensity is 10 times higher than that of standard CaSO{sub 4}:Dy. • Fading rate of SrSO{sub 4}:Eu phosphor is improved by 5% with Ag co-doping. • Linear dose response in the range 10mGy-10Gy. • t .

Electronic and magnetic properties of triple-layered ruthenate Sr4Ru3O10 single crystals grown by a floating-zone method

International Nuclear Information System (INIS)

Zhou, M.; Hooper, J.; Fobes, D.; Mao, Z.Q.; Golub, V.; O'Connor, C.J.

2005-01-01

We have grown high-quality single crystals of the triple-layered perovskite ruthenate Sr 4 Ru 3 O 10 using a floating-zone (FZ) method and measured their electronic transport and magnetic properties. Our experiments results are consistent with those previously reported for Sr 4 Ru 3 O 10 flux crystals; the magnetic ground state of Sr 4 Ru 3 O 10 is poised between an itinerant metamagnetic and itinerant ferromagnetic state, and its electronic ground state is a Fermi liquid. In addition, we have investigated the effect of disorder on the metallic state of Sr 4 Ru 3 O 10 . From resistivity measurements of various Sr 4 Ru 3 O 10 crystals with different levels of disorder, we found that disorder enhances both temperature-independent elastic scattering and also temperature-dependent inelastic scattering. The in-plane metamagnetic transition is also found to be sensitive to disorder. Disorder results in an increase in the metamagnetic transition field and different magnetic behavior above the transition. We discuss the implications of this interesting observation

Reversible tuning of a series of intergrowth phases of the Ruddlesden-Popper type SrO(SrTiO3)n in an (001) SrTiO3 single-crystalline plate by an external electric field and its potential use for adaptive X-ray optics

International Nuclear Information System (INIS)

Meyer, D.C.; Levin, A.A.; Leisegang, T.; Gutmann, E.; Paufler, P.; Reibold, M.; Pompe, W.

2006-01-01

Reversible structural changes of near-electrode regions of an (001) SrTiO 3 (STO) single-crystal plate with perovskite-type of structure in an external electric field are described as the tunable and reversible formation of a significant volume of domains containing Ruddlesden-Popper (RP) phases of composition SrO(SrTiO 3 ) n with variable n. Compositional changes are discussed to be caused by electromigration of ion complexes in the static electric field, i.e., by solid state electrolysis of the perovskite STO. Electromigration is initiated by the electric field which then stabilizes the RP domains formed. The RP domains can be described as coherently intergrown with the surrounding perovskite matrix. The X-ray scattering behaviour of these intergrowths, compared with the perovskite STO, suggests the technical use of the phenomenon for adaptive X-ray optics. (orig.)

Magnetoelectric Response in Multiferroic SrFe12O19 Ceramics.

Directory of Open Access Journals (Sweden)

Guolong Tan

Full Text Available We report here realization of ferroelectricity, ferromagnetism and magnetocapacitance effect in singleSrFe12O19ceramic at room temperature. The ceramics demonstrate a saturated polarization hysteresis loop, two nonlinear I-V peaks and large anomaly of dielectric constant near Curie temperature, which confirm the intrinsic ferroelectricity of SrFe12O19 ceramicswith subsequent heat-treatment in O2atmosphere. The remnant polarization of the SrFe12O19 ceramic is estimated to be 103μC/cm2. The ceramic also exhibits strong ferromagnetic characterization, the coercive field and remnant magnetic moment are 6192Oe and 35.8emu/g, respectively. Subsequent annealing SrFe12O19 ceramics in O2 plays a key role on revealing its intrinsic ferroelectricity and improving the ferromagnetism through transforming Fe2+ into Fe3+. By applying a magnetic field, the capacitance demonstrates remarkable change along with B field, the maximum rate of change in ε (Δε(B/ε(0 is 1174%, which reflects a giant magnetocapacitance effect in SrFe12O19. XPS and molecular magnetic moment measurements confirmed the transformation of Fe2+ into Fe3+ and removal of oxygen vacancies upon O2 heat treatment. These combined functional responses in SrFe12O19 ceramics opens substantial possibilities for applications in novel electric devices.

Carrier density independent scattering rate in SrTiO3-based electron liquids.

Science.gov (United States)

Mikheev, Evgeny; Raghavan, Santosh; Zhang, Jack Y; Marshall, Patrick B; Kajdos, Adam P; Balents, Leon; Stemmer, Susanne

2016-02-10

We examine the carrier density dependence of the scattering rate in two- and three-dimensional electron liquids in SrTiO3 in the regime where it scales with T(n) (T is the temperature and n ≤ 2) in the cases when it is varied by electrostatic control and chemical doping, respectively. It is shown that the scattering rate is independent of the carrier density. This is contrary to the expectations from Landau Fermi liquid theory, where the scattering rate scales inversely with the Fermi energy (EF). We discuss that the behavior is very similar to systems traditionally identified as non-Fermi liquids (n density-independent scattering rates have been observed. The results indicate that the applicability of Fermi liquid theory should be questioned for a much broader range of correlated materials and point to the need for a unified theory.

Effect of cooling rate on the transition temperature in Bi-Pb-Sr-Ca-Cu-O system

International Nuclear Information System (INIS)

Wang Yugui; Wang Jinsong; Wang Nanlin; Jiao Xinping; Han Guchang; Chen Zhaojia; Wang Keqin; Wu Xiaoguang

1989-12-01

The resistance and a.c. susceptibility measurement show that cooling rate of the cast-annealing samples in heat treatment process has some effect on the 110K superconducting phase in Bi-Pb-Sr-Ca-Cu-O system. Rapid quenching of the sample in air from 845 deg C causes oxygen deficiency in lattice and brings about a trifling change of unit cell size along c-axis direction. The d.c. magnetization and specific heat anomaly Δc measurements demostrate that fast cooling rate can reduce the transition temperature of high-T c phase and the lower critical field, and weaken the pinning forces for vertex lines. The peak value of specific heat anomaly of the sample with nominal composition of Bi 1.7 Pb 0.3 Sr 2 Ca 2 Cu 4.5 O v is still small in comparison with YBa 2 Cu 3 O 7 . From the magnetization curve the authors estimate that the superconducting volume fraction is about 20%

Possible two-stage /sup 87/Sr evolution in the Stockdale Rhyolite

Energy Technology Data Exchange (ETDEWEB)

Compston, W.; McDougall, I. (Australian National Univ., Canberra. Research School of Earth Sciences); Wyborn, D. (Department of Minerals and Energy, Canberra (Australia). Bureau of Mineral Resources)

1982-12-01

The Rb-Sr total-rock data for the Stockdale Rhyolite, of significance for the Palaeozoic time scale, are more scattered about a single-stage isochron than expected from experimental error. Two-stage /sup 87/Sr evolution for several of the samples is explored to explain this, as an alternative to variation in the initial /sup 87/Sr//sup 86/Sr which is customarily used in single-stage dating models. The deletion of certain samples having very high Rb/Sr removes most of the excess scatter and leads to an estimate of 430 +- 7 m.y. for the age of extrusion. There is a younger alignment of Rb-Sr data within each sampling site at 412 +- 7 m.y. We suggest that the Stockdale Rhyolite is at least 430 m.y. old, that its original range in Rb/Sr was smaller than now observed, and that it experienced a net loss in Sr during later hydrothermal alteration at ca. 412 m.y.

Controlled reduction and oxidation of La0.85Sr0.15MnO3 single crystals

International Nuclear Information System (INIS)

De Leon-Guevara, A.M.; Berthet, P.; Berthon, J.; Millot, F.; Revcolevschi, A.

1997-01-01

La 0.85 Sr 0.15 MnO 3 single crystals were grown by the floating zone method. They can be reversibly reduced under controlled oxygen partial pressure. Their defect chemistry is investigated together with the evolution of their cell parameters and that of their electric conductivity which is very sensitive to their oxygen content. On the other hand, stoichiometric crystals can be oxidized with a slow kinetics making possible the preparation of diphasic materials. (orig.)

Estimating accidental coincidences for pixelated PET detectors and singles list-mode acquisition

International Nuclear Information System (INIS)

Rafecas, M.; Torres, I.; Spanoudaki, V.; McElroy, D.P.; Ziegler, S.I.

2007-01-01

We have studied the validity of random estimation techniques for various low energy thresholds (LETs) and single list-mode data sets in small animal PET. While a LET below 255 keV helps to increase the sensitivity, it also results in an increase of random coincidences and inter-crystal scatter (ICS). The study is carried out for MADPET-II, a dual-layer positron emission tomography (PET) scanner prototype consisting of LSO crystals read out individually by APDs. The data are acquired in singles list-mode format, and coincidences are computed post-acquisition. To estimate randoms, we have used the delayed coincidence window method (DW), and the singles rate model (SR). Various phantoms were simulated using GATE. For LETs under 255 keV, the number of random events R, estimated using the SR and the DW methods, is larger than the number of randoms which was directly computed from GATE simulations, and R(SR)>R(DW)>R(GATE). The higher the LET, the smaller the overestimation. For LETs >255 keV, R(DW)/R(GATE) ∼1. If scattered singles were excluded from the file, this discrepancy between R(DW or SR) and R(GATE) significantly diminished. This fact points out to ICS as the effect responsible for the mismatch, since for LETs lower than 255 keV, all singles related to an ICS event can be detected independently, thus altering the singles rate. Therefore, if low LETs are used, random estimation techniques should account for ICS

Structural and compositional characterization of synthetic (Ca,Sr)-tremolite and (Ca,Sr)-diopside solid solutions

Science.gov (United States)

Gottschalk, M.; Najorka, J.; Andrut, M.

Tremolite (CaxSr1-x)2Mg5[Si8O22/(OH)2] and diopside (CaxSr1-x)Mg[Si2O6] solid solutions have been synthesized hydrothermally in equilibrium with a 1 molar (Ca,Sr)Cl2 aqueous solution at 750°C and 200 MPa. The solid run products have been investigated by optical, electron scanning and high resolution transmission electron microscopy, electron microprobe, X-ray-powder diffraction and Fourier-transform infrared spectroscopy. The synthesized (Ca,Sr)-tremolites are up to 2000 µm long and 30 µm wide, the (Ca,Sr)-diopsides are up to 150 µm long and 20 µm wide. In most runs the tremolites and diopsides are well ordered and chain multiplicity faults are rare. Nearly pure Sr-tremolite (tr0.02Sr-tr0.98) and Sr-diopside (di0.01Sr-di0.99) have been synthesized. A continuous solid solution series, i.e. complete substitution of Sr2+ for Ca2+ on M4-sites exists for (Ca,Sr)-tremolite. Total substitution of Sr2+ for Ca2+ on M2-sites can be assumed for (Ca,Sr)-diopsides. For (Ca,Sr)-tremolites the lattice parameters a, b and β are linear functions of composition and increase with Sr-content whereas c is constant. For the diopside series all 4 lattice parameters are a linear function of composition; a, b, c increase and β decreases with rising Sr-content. The unit cell volume for tremolite increases 3.47% from 906.68 Å3 for tremolite to 938.21 Å3 for Sr-tremolite. For diopside the unit cell volume increases 4.87 % from 439.91 Å3 for diopside to 461.30 Å3 for Sr-diopside. The observed splitting of the OH stretching band in tremolite is caused by different configurations of the next nearest neighbors (multi mode behavior). Resolved single bands can be attributed to the following configurations on the M4-sites: SrSr, SrCa, CaCa and CaMg. The peak positions of these 4 absorption bands are a linear function of composition. They are shifted to lower wavenumbers with increasing Sr-content. No absorption band due to the SrMg configuration on the M4-site is observed. This indicates

Cu-NMR study on disordered Sr14Cu24O41

International Nuclear Information System (INIS)

Ohsugi, S.; Matsumoto, S.; Kitaoka, Y.; Matsuda, M.; Uehara, M.; Akimitsu, J.; Nagata, T.

2002-01-01

The ladder-Cu NMR spectrum of a structural disordered single crystal Sr 14 Cu 24 O 41 (Sr14-B) under a magnetic field H∝11 T gradually splits into two spectra with Curie-like broadening as T decreases from T SP ∝150 K. Short-range (SR) staggered polarization (SP) on the ladder planes, originating from single-hole localization, occurs. The separation of the Sr14-B spectrum ΔH deviates from the Curie-like T dependence below 20 K. This assures that spontaneous moments appear below T N ∝20 K in H∝11 T. (orig.)

Spectroscopic and electric dipole properties of Sr+Ar and SrAr systems including high excited states

Science.gov (United States)

Hamdi, Rafika; Abdessalem, Kawther; Dardouri, Riadh; Al-Ghamdi, Attieh A.; Oujia, Brahim; Gadéa, Florent Xavier

2018-01-01

The spectroscopic properties of the fundamental and several excited states of Sr+Ar and SrAr, Van der Waals systems are investigated by employing an ab initio method in a pseudo-potential approach. The potential energy curves and the spectroscopic parameters are displayed for the 1-10 2Σ+, 1-6 2Π and 1-3 2Δ electronic states of the Sr+Ar molecule and for the 1-6 1Σ+, 1-4 3Σ+, 1-3 1,3Π and 1-3 1,3Δ states of the neutral molecule SrAr. In addition, from these curves, the vibrational levels and their energy spacing are deduced for Σ+, Π and Δ symmetries. The spectra of the permanent and transition dipole moments are studied for the 1,3Σ+ states of SrAr, which are considered to be two-electron systems and 2Σ+ states of the single electron Sr+Ar ion. The spectroscopic parameters obtained for each molecular system are compared with previous theoretical and experimental works. A significant correlation revealed the accuracy of our results.

Ultrahigh vacuum STM/STS studies of the Bi-O surface in Bi2Sr2CuOy single crystals

International Nuclear Information System (INIS)

Ikeda, Kazuto; Tomeno, Izumi; Takamuku, Kenshi; Yamaguchi, Koji; Itti, Rittaporn; Koshizuka, Naoki

1992-01-01

Scanning tunneling microscopic and spectroscopic studies were made on cleaved surfaces of Bi 2 Sr 2 CuO y single crystals using an ultrahigh-vacuum scanning tunneling microscope (UHV-STM). The modulation structures of the Bi-O surface were observed at room temperature with atomic resolution. The tunneling spectra showed electronic gap structures similar to those observed for the Bi-O surface of superconducting Bi-2212 single crystals. This suggests that superconductivity is not directly related to the electronic structure observed in the Bi-O plane. (orig.)

Single-phase highly densified SrBi{sub 2}Ta{sub 2}O{sub 9} compacts produced by high-pressure sintering

Energy Technology Data Exchange (ETDEWEB)

Pereira, Altair Soria; Souza, Ricson Rocha de; Sousa, Vania Caldas de, E-mail: altair@if.ufrgs.br [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre (Brazil)

2016-07-01

Full text: The development of high-performance lead-free piezoelectric ceramics is an important scientific and technological challenge, as environmental and health issues have imposed restrictions to the use of lead zirconate titanates, the most employed material in ferroelectric devices [1]. Strontium bismuth tantalate (SBT),SrBi{sub 2}Ta{sub 2}O{sub 9}, is an interesting alternative ferroelectric material as its polarization can be modified at low voltages and it shows limited polarization switching fatigue. However, the production of highly densified single-phase bulk SBT by conventional sintering procedures is strongly compromised by stoichiometric changes due to bismuth loss. In this work, high-pressure sintering has been exploited as an alternative procedure to obtain SBT highly-densified single-phase compacts. Using toroidal-type high-pressure chambers, samples were produced by reaction sintering of BiTaO{sub 4} and SrCO{sub 3} powders, mixed in the stoichiometric ratio corresponding to SrBi{sub 2}Ta{sub 2}O{sub 9}, at pressures of 2.5 GPa and 7.7 GPa, and temperatures up to 1250°C, during 10 min. X-ray diffraction and scanning electron microscopy associated to energy-dispersive X-ray spectroscopy were used to follow the phase composition and the microstructure evolution as a function of the processing conditions. A single-phase SBT compact, with a relative density of 93% and a homogeneous microstructure, was produced by sintering at 2.5 GPa/900°C [2]. References: [1] K. Panda, J. Mater. Sci. 44, 5049-5062 (2009). [2] Ricson R.Souza, Rejane K. Kirchner, Jose R. Jurado, Altair S. Pereira, Vania C. Sousa. Journal of Solid State Chemistry 233, 259-268 (2016). (author)

Growth and properties of oxygen doped Bi2Sr2CaCu2O8+δ single crystals

International Nuclear Information System (INIS)

Kapitulnik, A.; Mitzi, D.B.

1990-01-01

This paper reports results on oxygen doped single crystals in the Bi 2 Sr 2 CaCu 2 O 8+δ system grown by a directional solidification method. Annealing of as made crystals in increasing partial pressure of oxygen reversibly depresses the superconducting transition temperature from 90K (as made) to 77K (oxygen pressure annealed). Magnetic and photoemission properties of these crystals will be discussed

Spatially resolved resistivity near the vortex lattice phase transition in Bi 2Sr 2CaCu 2O 8+δ single crystals

Science.gov (United States)

Berseth, V.; Indenbom, M. V.; van der Beek, C. J.; D'Anna, G.; Benoit, W.

1997-08-01

Using a multiterminal contact configuration, we investigate the local variations of the resistivity drop near the vortex lattice first order phase transition in a very homogeneous Bi2Sr2CaCu2O8+δ (BSCCO) single crystal.

Hall coefficients and optical properties of La/sub 2-//sub x/Sr/sub x/CuO4 single-crystal thin films

International Nuclear Information System (INIS)

Suzuki, M.

1989-01-01

The low-field Hall coefficient R/sub H/, optical reflectance and transmittance of the La/sub 2-//sub x/Sr/sub x/CuO 4 system with various Sr concentrations from x = 0 to 0.36 are systematically studied using single-crystal thin films epitaxially grown on (100) face SrTiO 3 substrates with the c axis normal to the film surface. For the x range measured, R/sub H/ is positive and decreases more rapidly than that expected from the Sr concentration but more slowly than reported earlier for polycrystalline specimens, indicating anisotropy of R/sub H/. Furthermore, the x dependence indicates deviation from that expected from a simple band model. Within the superconducting composition range, R/sub H/ exhibits characteristic temperature dependence. The optical reflectance spectrum changes from that of a semiconductor at x = 0 to a typical metallic one characterized by the Drude model for x>0.1, indicating the development of itinerant holes in the Cu-O planes. In the optical transmission spectra, an anomalous absorption band is seen in addition to the fundamental absorption corresponding to an energy gap of about 2 eV. This band, which develops with Sr doping, implies an enhancement of the density of states near the Fermi level. Taking these observations into account, the normal-state transport properties are explained with a qualitative consistence

Preparation and characterization of Bi2Sr2CaCu2O8+δ thin films on MgO single crystal substrates by chemical solution deposition

DEFF Research Database (Denmark)

Grivel, Jean-Claude; Kepa, Katarzyna; Hlásek, T.

2013-01-01

Bi2Sr2CaCu2O8 thin films have been deposited on MgO single crystal substrates by spin-coating a solution based on 2-ethylhexanoate precursors. Pyrolysis takes place between 200°C and 450°C and is accompanied by the release of 2-ethylhexanoic acid, CO2 and H2O vapour. Highly c-axis oriented Bi2Sr2Ca...

Assessing Covariation of Holocene Monsoon Intensity and Local Moisture Conditions in Eastern and Southwestern Amazon Basin Using Speleothem δ18O and 87Sr/86Sr Values

Science.gov (United States)

Ward, B. M.; Wong, C. I.; Novello, V. F.; Silva, L.; McGee, D.; Cheng, H.; Wang, X.; Edwards, R. L.; Cruz, F. W., Sr.; Santos, R. V.

2017-12-01

δ18O records from South America offer insight into past variability of the South American Monsoon System (SAMS). Potential, however, for understanding local moisture conditions is limited as precipitation δ18O is strongly influenced by regional climate dynamics. Here we create Holocene speleothem 87Sr/86Sr records at 200-yr resolution using TIMS methods in the Center for Isotope Geochemistry at Boston College to complement existing Holocene δ18O speleothem records and investigate local moisture conditions above caves located in the eastern Amazon Basin (PAR - 4°S, 55°W) and southwestern Brazil (JAR - 21°S, 56°W). Speleothem 87Sr/86Sr variability is interpreted to reflect differences in the extent of water-rock interaction due to differences in infiltration rates under wet and dry conditions. Drier conditions promote longer residence time, enhanced water-rock interaction, and greater evolution of dripwater 87Sr/86Sr values from an initial isotopic signature acquired from the soil to the signature of the cave host rock. PAR speleothem 87Sr/86Sr values range from 0.71024 to 0.71067 and are bracketed by soil (0.71710 to 0.70956) and bedrock (0.70852 to 0.70899) values. JAR speleothem 87Sr/86Sr values range from 0.71216 to 0.71539 and are greater than bedrock values (0.70825 to 0.71219), although some speleothem values exceed the single analysis conducted of the soil isotopic composition (0.71473). JAR speleothem 87Sr/86Sr values increase from the early to mid Holocene, consistent with increase in local moisture availability associated with intensification of the SAMS suggested by decreasing δ18O values in many records from the region. Speleothem 87Sr/86Sr values at JAR decrease from the mid to late Holocene, consistent with an increase in δ18O values at PAR that suggest a decline in monsoon intensity. 87Sr/86Sr variability at JAR, however, is positively correlated with the δ18O record. Preliminary 87Sr/86Sr results from PAR are only broadly consistent with

Enhancement of white-light-emission from single-phase Sr5(PO4)3F:Eu(2+),Mn(2+) phosphors for near-UV white LEDs.

Science.gov (United States)

Feng, Yaomiao; Huang, Jinping; Liu, Lili; Liu, Jie; Yu, Xibin

2015-09-07

A series of single-phase broadband white-light-emitting Sr5(PO4)3F:Eu(2+),Mn(2+) phosphors were prepared by a solid state reaction. The luminescence property, and the crystal and electronic structures of the fluorophosphates were studied by photoluminescence analysis, XRD Rietveld refinement and density functional theory calculation (DFT), respectively. Under near ultraviolet excitation in the 250 to 430 nm wavelength range, the phosphors exhibit two emission bands centered at 440 and 556 nm, caused by the Eu(2+) and Mn(2+) ions. By altering the relative ratios of Eu(2+) and Mn(2+) in the compounds, the emission color could be modulated from blue to white. The efficient energy transfer from the Eu(2+) to Mn(2+) ions could be ascribed to the well crystallized host lattice and the facile substitution of Eu(2+) and Mn(2+) for Sr(2+) sites due to similar ionic radii. A series of fluxes were investigated to improve the photoluminescence intensity. When KCl was used as flux in the synthesis, the photoluminescence intensity of Sr5(PO4)3F:Eu(2+),Mn(2+) was enhanced by 85% compared with no fluxes added. These results demonstrate that the single-phase Sr5(PO4)3F:Eu(2+),Mn(2+) with enhanced luminescence efficiency could be promising as a near UV-convertible direct white-light-emitting phosphor for WLED applications.

The influence of Sr on the microstructure, degradation and stress corrosion cracking of the Mg alloys - ZK40xSr.

Science.gov (United States)

Chen, Lianxi; Bin, Yuanhong; Zou, Wenqi; Wang, Xiaojian; Li, Wei

2017-02-01

In the present work, new magnesium (Mg) alloys (Mg-4Zn-0.6Zr-xSr, x=0, 0.4, 0.8, 1.2, 1.6wt%; ZK40xSr) were prepared and studied as potential biodegradable materials. The influence of strontium (Sr) addition on the properties of the new Mg alloys was investigated, which included microstructure, corrosion degradation, and the stress corrosion cracking (SCC) susceptibility. The average grain size of the ZK40Sr was approximately 100µm, which was significantly smaller than that of ZK40 alloy without Sr (402.3±40.2µm). The size of grain boundaries precipitates in the ZK40xSr alloys gradually increased with the increase of Sr content. The grain boundaries finally showed a continuously distribution and net-like shape. The degradation test showed that the average degradation rate of the ZK40xSr alloys increased with the increase of Sr addition. In the case of Mg-4Zn-0.6Zr, the degradation rate was 2.2mgcm -2 day -1 , which was lower than that of Mg-4Zn-0.6Zr-1.6Sr (4.93mgcm -2 day -1 ). When the ZK40xSr alloys were immersed in m-SBF, the rod-like Sr-contained hydroxyapatite (HA) substance was detected, which was known to enhance cell growth around bone implants. The fracture surfaces of the as-cast Mg-4Zn-0.6Zr-1.6Sr were shown intergranular stress corrosion cracking (IGSCC) patterns. The increase of SCC susceptibility of the higher Sr ZK40xSr alloys was attributed to the increase of micro-galvanic corrosion between the α-Mg and the grain boundaries precipitates. The SCC susceptibility values were ≈0.13 and ≈0.41 for the Mg-4Zn-0.6Zr-0.4Sr and the Mg-4Zn-0.6Zr-1.6Sr, respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

Changes in local surface structure and Sr depletion in Fe-implanted SrTiO{sub 3} (001)

Energy Technology Data Exchange (ETDEWEB)

Lobacheva, O., E-mail: olobache@gmail.com [Department of Physics and Astronomy, Western University, London, ON N6A 5B7 (Canada); Yiu, Y.M. [Department of Chemistry, Western University, London, ON N6A 5B7 (Canada); Chen, N. [Canadian Light Source, Saskatoon, SK S7N 0X4 (Canada); Sham, T.K.; Goncharova, L.V. [Department of Physics and Astronomy, Western University, London, ON N6A 5B7 (Canada); Department of Chemistry, Western University, London, ON N6A 5B7 (Canada)

2017-01-30

Highlights: • Fe ion implantation of SrTiO{sub 3} and post-implantation results in formation of Sr{sub 1-y}Ti{sub 1-x}Fe{sub x+y}O{sub 3-δ} phase. • In Sr{sub 1-y}Ti{sub 1-x}Fe{sub x+y}O{sub 3-δ} phase, Fe assumes Fe{sup 3+} oxidation state in the bulk and Fe{sup 2+} oxidation state in the near surface area. • FEFF9 calculations indicate that Fe ions can substitute both Ti and Sr sites. • Formation of Sr{sub 1-y}Ti{sub 1-x}Fe{sub x+y}O{sub 3-δ} phase is accompanied by Sr depletion in the near surface region. - Abstract: Local surface structure of single crystal strontium titanate SrTiO{sub 3} (001) samples implanted with Fe in the range of concentrations between 2 × 10{sup 14} to 2 × 10{sup 16} Fe/cm{sup 2} at 30 keV has been investigated. In order to facilitate Fe substitution (doping), implanted samples were annealed in oxygen at 350 °C. Sr depletion was observed from the near-surface layers impacted by the ion-implantation process, as revealed by Rutherford Backscattering Spectrometry (RBS), X-ray photoelectron spectroscopy (XPS), X-ray Absorption Near Edge Spectroscopy (XANES), and Atomic Force Microscopy (AFM). Hydrocarbon contaminations on the surface may contribute to the mechanisms of Sr depletion, which have important implications for Sr(Ti{sub 1-x}Fe{sub x})O{sub 3-δ} materials in gas sensing applications.

Preparation of Sr7Mn4O13F2 by the topotactic reduction and subsequent fluorination of Sr7Mn4O15.

Science.gov (United States)

Saratovsky, Ian; Lockett, Michelle A; Rees, Nicholas H; Hayward, Michael A

2008-06-16

The topotactic reduction and subsequent fluorination of Sr7Mn4O15 yields a phase of composition Sr7Mn4O13F2. Characterization of this phase utilizing powder neutron diffraction and 19F NMR shows that the fluoride ions are located on a single anion site, the same crystallographic site that is vacant in the reduced intermediate Sr7Mn4O13.

XPS Analysis of Ni and Oxygen in Single-Sintered SrTiO3 Multifunction Ceramic

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

XPS analyses have been performed to investigate the chemical conditions of Ni and oxygen on grain surfaces in single-sintered SrTiO3 capacitor-varistor ceramic doped with Nb2O5 and NiO. It is ascertained that Ni is in form of Ni2+ ions, which substitute for Ti4+ ions on grain surfaces during the oxidizing annealing. Moreover, it is confirmed that three kinds of chemically adsorbed oxygen such as O2-, O- and O~ are formed on grain surfaces. It is proposed that these behaviors contribute greatly to the generation of multiple types of grain boundary acceptor states in the ceramic.

Spin dynamics in the low-temperature tetragonal phase of congruent with ( 1/ 8 ) doped single crystal La1.67Eu0.2Sr0.13CuO4

International Nuclear Information System (INIS)

Suh, B. J.; Hammel, P. C.; Huecker, M.; Buechner, B.; Ammerahl, U.; Revcolevschi, A.

2000-01-01

We present 139 La and 63 Cu NMR relaxation measurements in single crystal La 1.67 Eu 0.2 Sr 0.13 CuO 4 . A strong peak in the 139 La spin-lattice relaxation rate observed in the spin ordered state is well described by the BPP mechanism [Bloembergen, Purcell, and Pound, Phys. Rev. 73, 679 (1948)] and arises from continuous slowing of electronic spin fluctuations with decreasing temperature; these spin fluctuations exhibit XY-like anisotropy in the ordered state. The spin pseudogap is significantly enhanced by the static charge-stripe order in the LTT phase. (c) 2000 The American Physical Society

High-pressure synthesis and crystal structures of the strontium oxogallates Sr2Ga2O5 and Sr5Ga6O14

International Nuclear Information System (INIS)

Kahlenberg, Volker; Goettgens, Valerie; Mair, Philipp; Schmidmair, Daniela

2015-01-01

High-pressure synthesis experiments in a piston–cylinder apparatus at 1.5 GPa/3.0 GPa and 1000 °C resulted in the formation of single-crystals of Sr 2 Ga 2 O 5 and Sr 5 Ga 6 O 14 , respectively. The structures of both compounds have been solved from single-crystal diffraction data sets using direct methods. The first compound is orthorhombic with space group type Pbca (a=10.0021(4) Å, b=9.601(4) Å, c=10.6700(4) Å, V=1024.6(4) Å 3 , M r =394.68 u, Z=8, D x =5.12 g/cm 3 ) and belongs to the group of single layer gallates. Individual sheets are parallel to (0 0 1) and can be built from the condensation of unbranched vierer single chains running along [0 1 0]. The layers are characterized by the presence of four- and strongly elliptical eight-membered rings of corner connected tetrahedra in UUDD and UUUUDDDD conformation. Strontium atoms are sandwiched between the tetrahedral layers for charge compensation and are coordinated by six and seven oxygen ligands, respectively. Sr 2 Ga 2 O 5 is isotypic with several other double sulfides and selenides. To the best of our knowledge, it is the first example of an oxide with this structure type. From a structural point of view, Sr 5 Ga 6 O 14 is a phyllogallate as well. The crystal structure adopts the monoclinic space group P2 1 /c (a=8.1426(3) Å, b=8.1803(3) Å, c=10.8755(4) Å, β=91.970(4)° V=723.98(5) Å 3 , M r =1080.42 u, Z=2, D x =4.96 g/cm 3 ). Individual sheets extend along (0 0 1). Basic building units are unbranched dreier single chains parallel to [1 0 0]. The layers contain tertiary (Q 3 ) und quaternary (Q 4 ) connected [GaO 4 ]-tetrahedra in the ratio 2:1 resulting in a Ga:O ratio of 3:7 and the formation of exclusively five-membered rings. Linkage between adjacent tetrahedral sheets is provided by three symmetrically independent strontium ions which are surrounded by six to eight oxygen atoms. The layers in Sr 5 Ga 6 O 14 are similar to those observed in the melilite structure-type. Crystallochemical

Probing single magnon excitations in Sr2IrO4 using O K-edge resonant inelastic x-ray scattering

International Nuclear Information System (INIS)

Liu, X; Ding, H; Dean, M P M; Yin, W G; Hill, J P; Liu, J; Ramesh, R; Chiuzbăian, S G; Jaouen, N; Nicolaou, A; Serrao, C Rayan

2015-01-01

Resonant inelastic x-ray scattering (RIXS) at the L-edge of transition metal elements is now commonly used to probe single magnon excitations. Here we show that single magnon excitations can also be measured with RIXS at the K-edge of the surrounding ligand atoms when the center heavy metal elements have strong spin–orbit coupling. This is demonstrated with oxygen K-edge RIXS experiments on the perovskite Sr 2 IrO 4 , where low energy peaks from single magnon excitations were observed. This new application of RIXS has excellent potential to be applied to a wide range of magnetic systems based on heavy elements, for which the L-edge RIXS energy resolution in the hard x-ray region is usually poor. (fast track communication)

Two-step transition towards the reversibility region in Bi2Sr2CaCu2O8-δ single crystals

Science.gov (United States)

Pastoriza, H.; de La Cruz, F.; Mitzi, D. B.; Kapitulnik, A.

1992-10-01

We have performed magnetization measurements on Bi2Sr2CaCu2O8-δ single crystals in the c^ crystallographic direction for fields from 2 Oe up to 700 Oe. The results strongly suggest that the reversible thermodynamic region is achieved after the vortex flux structure shows an abrupt transition at a temperature lower than that determined by the irreversibility line.

Growth and properties of oxygen- and ion-doped Bi2Sr2CaCu2O8+δ single crystals

International Nuclear Information System (INIS)

Mitzi, D.B.; Lombardo, L.W.; Kapitulnik, A.; Laderman, S.S.; Jacowitz, R.D.

1990-01-01

A directional solidification method for growing large single crystals in the Bi 2 Sr 2 CaCu 2 O 8+δ system is reported. Ion doping, with replacement of La for Sr and Y for Ca, as well as oxygen doping in these crystals has been explored. Doped and undoped crystals have been characterized using microprobe analysis, x-ray diffraction, thermogravimetric analysis, and magnetic and Hall measurements. Ion doping results in little change of the superconducting transition for substitution levels below 20--25%, while beyond this level the Meissner signal broadens and the low-temperature Meissner signal decreases. Microprobe analysis and x-ray diffraction performed on these more highly substituted single crystals provide evidence for inhomogeneity and phase segregation into regions of distinct composition. Annealing unsubstituted crystals in increasing partial pressures of oxygen reversibly depresses the superconducting transition temperature from 90 (as made) to 77 K (oxygen pressure annealed), while the carrier concentrations, as determined from Hall effect measurements, increase from n=3.1(3)x10 21 cm -3 (0.34 holes per Cu site) to 4.6(3)x10 21 cm -3 (0.50 holes per Cu site)

Magnetic penetration depth and flux dynamics in single-crystal Bi2Sr2CaCu2O8+δ

International Nuclear Information System (INIS)

Harshman, D.R.; Kleiman, R.N.; Inui, M.; Espinosa, G.P.; Mitzi, D.B.; Kapitulnik, A.; Pfiz, T.; Williams, D.L.

1991-01-01

The muon-spin-relaxation technique has been used to study vortex dynamics in single-phase superconducting single crystals of Bi 2 Sr 2 CaCu 2 O 8+δ (T c ∼90 K). The data indicate motional narrowing of the internal field distribution due to vortex motion (on a time scale comparable to the muon lifetime). A field-dependent lattice transition is also observed at T x ∼30 K, as evidenced by the onset of an asymmetric line shape below T x . Narrowing arising from disordering of the vortices along [001] is also discussed with reference to its effect on the measured penetration depth

Surface modeling and chemical solution deposition of SrO(SrTiO3)n Ruddlesden-Popper phases

International Nuclear Information System (INIS)

Zschornak, M.; Gemming, S.; Gutmann, E.; Weissbach, T.; Stoecker, H.; Leisegang, T.; Riedl, T.; Traenkner, M.; Gemming, T.; Meyer, D.C.

2010-01-01

Strontium titanate (STO) is a preferred substrate material for functional oxide growth, whose surface properties can be adjusted through the presence of Ruddlesden-Popper (RP) phases. Here, density functional theory (DFT) is used to model the (1 0 0) and (0 0 1) surfaces of SrO(SrTiO 3 ) n RP phases. Relaxed surface structures, electronic properties and stability relations have been determined. In contrast to pure STO, the near-surface SrO-OSr stacking fault can be employed to control surface roughness by adjusting SrO and TiO 2 surface rumpling, to stabilize SrO termination in an SrO-rich surrounding or to increase the band gap in the case of TiO 2 termination. RP thin films have been epitaxially grown on (0 0 1) STO substrates by chemical solution deposition. In agreement with DFT results, the fraction of particular RP phases n = 1-3 changes with varying heating rate and molar ratio Sr:Ti. This is discussed in terms of bulk formation energy.

Climatic Constraints on Growth Rate and Geochemistry (Sr/Ca and U/Ca) of the Coral Siderastrea stellata in the Southwest Equatorial Atlantic (Rocas Atoll, Brazil)

Science.gov (United States)

Evangelista, H.; Sifeddine, A.; Corrège, T.; Servain, J.; Dassié, E. P.; Logato, R.; Cordeiro, R. C.; Shen, C.-C.; Le Cornec, F.; Nogueira, J.; Segal, B.; Castagna, A.; Turcq, B.

2018-03-01

Although relatively rare compared to similar latitudes in the Pacific or Indian Oceans, massive coral colonies are present in the Tropical/Equatorial Southwestern Atlantic Ocean. However, detailed geochemical compositions of these corals are still largely unknown. In this work, we present growth rates, Sr/Ca, and U/Ca ratios of the coral colony (Siderastrea stellata) sampled at Rocas Atoll, off the Brazilian coast. These variables are primarily affected by sea surface temperature (SST) at seasonal scale, and by wind stress at interannual scale, these results represent a broad new finding. A lower significance at the interannual time scale between Sr/Ca and U/Ca with respect to SST is attributed to the low SST amplitude closed to Equator. An investigation on the dependence of coral growth rates with respect to the "cloud shading effect" promoted by the Intertropical Convergence Zone (ITCZ) does not show significant influence. Additionally, rain seems to act on local geochemistry of Sr/Ca ratios and growth rate at the decadal scale.

(Ba+Sr)/Ti ratio dependence of the dielectric properties for (Ba0.5Sr0.5)TiO3 thin films prepared by ion beam sputtering

Science.gov (United States)

Yamamichi, Shintaro; Yabuta, Hisato; Sakuma, Toshiyuki; Miyasaka, Yoichi

1994-03-01

(Ba0.5Sr0.5)TiO3 thin films were prepared by ion beam sputtering from powder targets with (Ba+Sr)/Ti ratios ranging from 0.80 to 1.50. All of the perovskite (Ba,Sr)TiO3 films were single phase except for the film with a (Ba+Sr)/Ti ratio of 1.41. The dielectric constant values notably depended on the (Ba+Sr)/Ti ratio for films thicker than 70 nm. The highest dielectric constant of 580 was achieved for the 5% (Ba+Sr) rich film. This (Ba+Sr)/Ti ratio dependence was diminished by the thickness dependence for thinner films. The grain sizes for the 9% (Ba+Sr) rich film and for the 6% (Ba+Sr) poor film ranged from 70 to 100 nm and from 30 to 60 nm, respectively. This grain size difference could explain why slightly A-site rich (Ba,Sr)TiO3 films have a larger dielectric constant than A-site poor films.

Crystal structure and electronic states of Co and Gd ions in a Gd0.4Sr0.6CoO2.85 single crystal

Science.gov (United States)

Platunov, M. S.; Dudnikov, V. A.; Orlov, Yu. S.; Kazak, N. V.; Solovyov, L. A.; Zubavichus, Ya. V.; Veligzhanin, A. A.; Dorovatovskii, P. V.; Vereshchagin, S. N.; Shaykhutdinov, K. A.; Ovchinnikov, S. G.

2016-02-01

X-ray diffraction and X-ray absorption near edge structure (XANES) spectra have been measured at the Co K-edge and Gd L 3-edge in GdCoO3 and Gd0.4Sr0.6CoO2.85 cobaltites. The effect of Sr substitution on the crystal structure and electronic and magnetic states of Co3+ ions in a Gd0.4Sr0.6CoO2.85 single crystal has been analyzed. The XANES measurements at the Co K-edge have not showed a noticeable shift of the absorption edge with an increase in the concentration of Sr. This indicates that the effective valence of cobalt does not change. An increase in the intensity of absorption at the Gd L 3-edge is due to an increase in the degree of hybridization of the Gd(5 d) and O(2 p) states. The effect of hole doping on the magnetic properties results in the appearance of the ferromagnetic component and in a significant increase in the magnetic moment.

Hybrid HF-DFT comparative study of SrZrO{sub 3} and SrTiO{sub 3}(001) surface properties

Energy Technology Data Exchange (ETDEWEB)

Evarestov, R.A.; Bandura, A.V.; Alexandrov, V.E. [Department of Quantum Chemistry, St. Petersburg State University, 26 Universitetskii Prospekt, Stary Petergof, 198504 St. Petersburg (Russian Federation)

2006-10-15

Hybrid HF-DFT LCAO simulations of SrZrO{sub 3} and SrTiO{sub 3}(001) surface properties are performed in a single-slab model framework. The SrZrO{sub 3}(001) surface was studied by an ab initio method for the first time. Three slab models with different surface terminations including up to 8 atomic planes were used for calculation of the various surface characteristics (surface energies, atomic charges, density of electronic states). The dependence of the results on the chosen model and on the kind of d-element is analyzed. The dissimilarity in the surface oxygen atom contributions to the total density of states of two crystals is attributed to the more ionic nature of Zr-O bonds compared to Ti-O bonds. It is found that in the case of SrZrO{sub 3} the electronic density is biased towards the SrO-terminated surface and this surface should be more basic in nature than the SrO surface of SrTiO{sub 3} crystal. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Autoradiography of 90Sr in developing rats

International Nuclear Information System (INIS)

Olsen, I.; Jonsen, J.

1979-01-01

The distribution patterns of 90 Sr in five littermate, 8-day-old Wistar rats were studied by whole body autoradiography. Rats were killed 15 min, 1, 4, 24, and 72 h after a single intraperitoneal injection of the isotope. Immediately after administration, 90 Sr was distributed throughout most of the soft tissues of the body. The soft tissue deposits had practically disappeared after 4 h. In the hard tissues of the body 90 Sr accumulated up to 24-72 h. Fifteen minutes after injection the uptake of 90 Sr in the enamel of the teeth was highest in the occlusal and incisal regions. 90 Sr gradually accumulated throughout the enamel and after 72 h its distribution in this layer was fairly uniform. Immediately after injection a narrow zone of radioactivity appeared in the dentin near the pulp. This zone broadened with time towards the dentinoenamel junction and included the intire dentin layer 72 h after injection. Initially, the uptake of 90 Sr was higher in the dentin than in the enamel, particularly in the cervical areas of the crown. This difference became less apparent with time. There was good correlation between the uptake in the teeth and bones, supporting the use of teeth as indicators of the 90 Sr body burden. (author)

Demonstration of Entrained Solids and Sr/TRU Removal Processes with Archived AN-107 Waste

International Nuclear Information System (INIS)

Hallen, R.T.; Brooks, K.P.; Jagoda, L.K.

2000-01-01

Archived AN-107 waste was used to evaluate entrained solids removal, Sr/TRU decontamination of supernatant, and Sr/TRU solids removal. Even though most of the entrained solids had been previously removed from the archived sample, the residual entrained solids rapidly fouled the filter element resulting in very poor filter performance. An attempt to run at higher pressure resulted in more fouling, and reduced filter performance. Filtration efforts to remove entrained solids were abandoned and the waste was treated for Sr/TRU removal with the entrained solids present. The new processing scheme for Sr/TRU removal involving precipitation by added strontium and permanganate worked well. The decontamination factors for Sr and TRU components were significantly greater than the ILAW DF requirements for higher reagent concentrations of 1M hydroxide, 0.075M Sr, and 0.05M permanganate and lower reagent concentrations of 0.8M hydroxide, 0.05M Sr, and 0.03M permanganate. These results support the use of lower concentration of reagent additions in future tests. Optimization studies should be conducted to examine the reduction in added hydroxide from 1M to 0.5 M, reduction of Sr from 0.075M to 0.05M, and reduction in permanganate from 0.05M to 0.03M and the impact this reduction has on filtration performance with new samples from Tank AN-107. The combined entrained solids and Sr/TRU precipitate were successfully filtered in the single element, crossflow filtration unit. The filtrate flux was high, >0.1 gpm/ft 2 , at the initial test conditions of 53 psi and 11.2ft/s for the treated archived AN-107 sample. The filter flux rate dropped significantly with time as testing progressed and appears to be a result of shearing the agglomerated solids and fouling of the filter element by the resulting fine particles. The relatively low clean water flux rates obtained at the end of the test also indicate filter fouling. Chemical cleaning was required to restore clean water flux rates to pre

Photoconductive response of a single Au nanorod coupled to LaAlO3/SrTiO3 nanowires

International Nuclear Information System (INIS)

Jnawali, Giriraj; Chen, Lu; Huang, Mengchen; Lee, Hyungwoo; Ryu, Sangwoo; Podkaminer, Jacob P.; Eom, Chang-Beom; Irvin, Patrick; Levy, Jeremy

2015-01-01

Terahertz (THz) spectroscopy is an important tool that provides resonant access to free carrier motion, molecular rotation, lattice vibrations, excitonic, spin, and other degrees of freedom. Current methods using THz radiation suffer from limits due to diffraction or low-sensitivity, preventing application at the scale of single nanoscale objects. Here, we present coupling between plasmonic degrees of freedom in a single gold nanorod and broadband THz emission generated from a proximal LaAlO 3 /SrTiO 3 nanostructure. A strong enhancement of THz emission is measured for incident radiation that is linearly polarized along the long axis of the nanorod. This demonstration paves the way for the investigation of near-field plasmonic coupling in a variety of molecular-scale systems

Preparation of Sr adsorptive fiber by impregnating with crown ether derivative for 90Sr measurement

International Nuclear Information System (INIS)

Horita, Takuma; Asai, Shiho; Hanzawa, Yukiko; Kitatsuji, Yoshihiro; Konda, Miki; Saito, Kyoichi; Fujiwara, Kunio; Sugo, Takanobu

2017-01-01

A Sr adsorption fiber was prepared for rapid analysis of 90 Sr content in the fiber using radiation-induced emulsion graft polymerization and subsequent chemical modification. A polyethylene fiber with a diameter of 13 μm was first immersed in a methanol solution of an epoxy-group-containing vinyl monomer, glycidyl methacrylate (GMA), and polyoxyethylene sorbitol ester (Tween20) as a surfactant for the graft-polymerization of GMA. Octadecylamine was then bound to a polymer chain extending from the fiber surface, providing hydrophobicity to the polymer chain. Dicyclohexano-18-crown-6 (DCH18C6) was finally impregnated onto the polymer chain via a hydrophobic interaction between the octadecyl moiety of the polymer chain and the cyclohexyl moiety of DCH18C6. The fiber surface structure, characterized by DCH18C6 molecules loosely entangled with polymer chains, allowed for the rapid adsorption of Sr ions at an adsorption rate of approximately 100-times higher than that of a commercially available Sr-selective resin (Sr Resin ® ). (author)

Reaction of Rb and oxygen overlayers with single-crystalline Bi2Sr2CaCu2O/sub 8+//sub δ/ superconductors

International Nuclear Information System (INIS)

Lindberg, P.A.P.; Shen, Z.; Wells, B.O.; Dessau, D.S.; Mitzi, D.B.; Lindau, I.; Spicer, W.E.; Kapitulnik, A.

1989-01-01

Single crystals of Bi 2 Sr 2 CaCu 2 O/sub 8+//sub δ/ superconductors, in situ cleaved and modified by Rb and oxygen overlayers, have been studied using ultraviolet and x-ray photoemission spectroscopy. The core-level results show that Rb strongly reacts with the Bi and O states, while the Cu and Sr states are left unchanged. This observation strongly indicates that the Bi-O plane forms the surface layer. Subsequent exposure to oxygen results in new oxygen states at the surface as monitored by the O 1s core-level data. For both Rb and oxygen overlayers the valence-band spectra are severely altered. In particular, new valence-band states, presumably of oxygen character, are formed

Moessbauer studies of single crystal Pr sub 1 sub / sub 3 Sr sub 2 sub / sub 3 FeO sub 3

CERN Document Server

Uhm, Y R; Kim, C S; Tomioka, Y; Tokura, Y

2000-01-01

Single crystal Pr sub 1 sub / sub 3 Sr sub 2 sub / sub 3 FeO sub 3 was synthesized by using the floating zone method and the relation of magnetic properties and charge ordering transition with lattice dynamics was systematically investigated. Moessbauer spectra of Pr sub 1 sub / sub 3 sub S r sub 2 sub / sub 3 FeO sub 3 were taken at various temperatures ranging from 20 K to room temperature. The charge disproportionation, in which iron with valence states Fe sup 3 sup + and Fe sup 5 sup + was found in a ratio of 2:1, was detected in Pr sub 1 sub / sub 3 Sr sub 2 sub / sub 3 FeO sub 3 below 190+-3 K. Iron with valence state Fe sup 4 sup + coexisted in Pr sub 1 sub / sub 3 sub S r sub 2 sub / sub 3 FeO sub 3 at and above 150 K, and its ratio increased from 13 to 66 % with increasing temperature. This result means that charge-ordered and -disordered phases co-exist in Pr sub 1 sub / sub 3 Sr sub 2 sub / sub 3 FeO sub 3.

The coprecipitation of Sr2+ with calcite at 250C and 1 atm

International Nuclear Information System (INIS)

Pingitore, N.E. Jr.; Eastman, M.P.

1986-01-01

The incorporation of Sr 2+ into calcite at earth surface aqueous conditions is affected by the absolute concentration of Sr 2+ , the presence of Ba 2+ and NaCl in the solution and the rate of precipitation. At solution ratios (molar) of Sr 2+ to Ca 2+ in the low 10 -3 range, which yield calcites with several hundred ppm Sr 2+ , kappasub(calcite) sup(Sr) typically assumes a value between 0.10 and 0.20. Above these concentrations the value of kappasub(calcite) sup(Sr) drops to approximately 0.06. Furthermore, if minor amounts of Ba 2+ or large amounts of Na + (0.48 M) are added to a dilute Sr 2+ solution, a value around 0.06 for kappasub(calcite)sup(Sr) is found. This 'strontium concentration effect' and the associated 'competitive cation effect' suggest that small amounts of Sr 2+ may be incorporated into a limited number of nonlattice sites in calcite. Incorporation of Sr 2+ into these sites, presumably defects, noticeably affects kappasub(calcite)sup(Sr) only at low Sr 2+ concentrations and in the absence of competition from other large cations. An increase in kappasub(calcite)sup(Sr) with rate of precipitation, qualitatively similar to that found in other studies, was observed only when precipitation times were decreased from days to hours. For many geologic settings a partition coefficient for Sr 2+ into calcite of 0.06 appears appropriate, but there are situations - very low Sr 2+ concentrations, the presence of Mg 2+ , and fast precipitation rates - in which a larger value might better approximate natural partitioning. (author)

Quasi-two-dimensional Fermi-liquid state in Sr2RhO4-δ

International Nuclear Information System (INIS)

Nagai, Ichiro; Shirakawa, Naoki; Umeyama, Norio; Ikeda, Shin-ichi

2010-01-01

Single crystals of layered perovskite Sr 2 RhO 4-δ (δ=0.0 and 0.1) are successfully grown by the floating-zone method. Stoichiometric single crystals (Sr 2 RhO 4.0 ) are obtained by O 2 -annealing the as-grown crystals (Sr 2 RhO 3.9 ). Sr 2 RhO 4.0 and Sr 2 RhO 3.9 show quasi-two-dimensional Fermi-liquid behavior at low temperatures, whereas there are large differences in the anisotropy of electrical resistivity ρ c (3 K)/ρ ab (3 K) and Wilson ratio R w between Sr 2 RhO 4.0 and Sr 2 RhO 3.9 : ρ c (3 K)/ρ ab (3 K)=2400 (19000) and R w =3.8 (6.4) for Sr 2 RhO 4.0 (Sr 2 RhO 3.9 ). The differences observed between the temperature dependence of the in-plane electrical resistivity (T 2 RhO 4.0 and Sr 2 RhO 3.9 are mainly derived from those between the density of states and band structure near the corresponding Fermi level. This indicates that the changes in these physical properties, which are accompanied by oxygen defects in the Sr 2 RhO 4-δ system, can be explained by the rigid band model. Moreover, these results suggest that t 2g band-filling can be controlled by adjusting the oxygen defect content δ in the Sr 2 RhO 4-δ system. Although many similarities are observed in this study between the physical properties of Sr 2 RhO 4.0 and Sr 2 RuO 4 . Sr 2 RhO 4.0 does not exhibit superconductivity down to 36 mK. (author)

Regularity on absorption and accumulation of 90Sr in yellow-feather broiler (Hypeco)

International Nuclear Information System (INIS)

Xu Shiming; Hou Lanxin; Zhao Wenhu; Li Xia; Yang Zhongyuan

1996-02-01

The feeding experiment was carried for yellow-feather broiler (Hypeco) with 90 Sr[NO 3 ] 2 having of 1.85 x 10 2 ∼1.85 x 10 5 Bq/chicken to observe the regular pattern of absorption and accumulation of 90 Sr in its organs and tissues. The absorption rate of 90 Sr by oral feeding is very low. The most of 90 Sr is drained away by daily excreta from the body. The half-time of its feeding is within 24 hours. The more 90 Sr is fed, the more 90 Sr is absorbed, however, the uptake rate of 90 Sr is decreasing. The affinity of 90 Sr for bone is very strong and the partition ratio is about 90%∼99%. The absorption coefficient of 90 Sr in organs and tissues of broiler is presented. (2 refs., 9 tabs.)

High-pressure modifications of CaZn2, SrZn2, SrAl2, and BaAl2: Implications for Laves phase structural trends

International Nuclear Information System (INIS)

Kal, Subhadeep; Stoyanov, Emil; Belieres, Jean-Philippe; Groy, Thomas L.; Norrestam, Rolf; Haeussermann, Ulrich

2008-01-01

High-pressure forms of intermetallic compounds with the composition CaZn 2 , SrZn 2 , SrAl 2 , and BaAl 2 were synthesized from CeCu 2 -type precursors (CaZn 2 , SrZn 2 , SrAl 2 ) and Ba 21 Al 40 by multi-anvil techniques and investigated by X-ray powder diffraction (SrAl 2 and BaAl 2 ), X-ray single-crystal diffraction (CaZn 2 ), and electron microscopy (SrZn 2 ). Their structures correspond to that of Laves phases. Whereas the dialuminides crystallize in the cubic MgCu 2 (C15) structure, the dizincides adopt the hexagonal MgZn 2 (C14) structure. This trend is in agreement with the structural relationship displayed by sp bonded Laves phase systems at ambient conditions. - Graphical abstract: CeCu 2 -type polar intermetallics can be transformed to Laves phases upon simultaneous application of pressure and temperature. The observed structures are controlled by the valence electron concentration

Galvanomagnetic properties of atomic-disordered Sr2RuO4 single crystals

International Nuclear Information System (INIS)

Kar'kin, A.E.; Naumov, S.V.; Goshchitskij, V.N.; Balbashov, A.M.

2005-01-01

The effect of neutron-bombardment-induced atomic disorder on the galvanomagnetic properties of Sr 2 RuO 4 single crystals has been experimentally studied in a broad range of temperatures (1.7-380 K) and magnetic fields (up to 13.6 T). The disorder leads to the appearance of negative temperature coefficients for both the in-plane electric resistivity (ρ a ) and that along the c axis (ρ c ), as well as the negative magnetoresistance Δρ, which is strongly anisotropic to the magnetic field orientation (H || a and H || c), with the easy magnetization direction along the c axis and a weak dependence on the probing current direction in the low-temperature region. The experimental ρ a (T) and ρ c (T) curves obtained for the initial and radiation-disordered samples can be described in the framework of a theoretical model with two conductivity channels. The first channel corresponds to the charge carriers with increased effective masses and predominantly electron-electron scattering, the second channel corresponds to the charge carriers with lower effective masses exhibiting magnetic scattering at low temperatures [ru

A model-independent comparison of the rates of uptake and short term retention of 47Ca and 85Sr by the skeleton.

Science.gov (United States)

Reeve, J; Hesp, R

1976-12-22

1. A method has been devised for comparing the impulse response functions of the skeleton for two or more boneseeking tracers, and for estimating the contribution made by measurement errors to the differences between any pair of impulse response functions. 2. Comparisons were made between the calculated impulse response functions for 47Ca and 85Sr obtained in simultaneous double tracer studies in sixteen subjects. Collectively the differences between the 47Ca and 85Sr functions could be accounted for entirely by measurement errors. 3. Because the calculation of an impulse response function requires fewer a priori assumptions than other forms of mathematical analysis, and automatically corrects for differences induced by recycling of tracer and non-identical rates of excretory plasma clearance of tracer, it is concluded that differences shown in previous in vivo studies between the fluxes of Ca and Sr into bone can be fully accounted for by undetermined oversimplifications in the various mathematical models used to analyse the results of those studies. 85Sr is therefore an adequate tracer for bone calcium in most in vivo studies.

Construction of the seawater 87Sr/86Sr curve for the Cenozoic and Cretaceous: supporting data

International Nuclear Information System (INIS)

Koepnick, R.B.; Burke, W.H.; Denison, R.E.; Hetherington, E.A.; Nelson, H.F.; Otto, J.B.; Waite, L.E.

1985-01-01

We present the data used to construct the Cenozoic and Cretaceous portion of the Phanerozoic curve of seawater 87 Sr/ 86 Sr that had been given in summary form by W.H. Burke and coworkers. All Cenozoic samples (128) and 22 Cretaceous samples are foram-nannofossil oozes and limestones from DSDP cores distributed among 13 sites in the Atlantic, Pacific and Indian Oceans, and the Caribbean Sea. Non-DSDP Cretaceous samples (126) include limestone, anhydrite and phosphate samples from North America, Europe and Asia. Determination of the 87 Sr/ 86 Sr value of seawater at particular times in the past is based on comparison of ratios derived from coeval marine samples from widely separated geographic areas. The general configuration of the Cenozoic and Cretaceous curve appears to be strongly influenced by the history of plate interactions and sea-floor spreading. Specific rises and falls in the 87 Sr/ 86 Sr of seawater, however, may be caused by a variety of factors such as variation in lithologic composition of the crust exposed to weathering, configuration and topographic relief of continents, volcanic activity, rate of sea-floor spreading, extent of continental inundation by epeiric seas, and variations in both climate and paleo-oceanographic conditions. Many or all of these factors are probably related to global tectonic processes, yet their combined effect on the temporal variation of seawater 87 Sr/ 86 Sr can complicate a direct plate-tectonic interpretation for portions of the seawater curve. (Auth.)

Electronic structure of single crystalline Bi sub 2 (Sr,Ca,La) sub 3 Cu sub 2 O sub 8

Energy Technology Data Exchange (ETDEWEB)

Lindberg, P A.P.; Shen, Z X; Dessau, D S; Wells, B O; Borg, A; Mitzi, D B; Lindau, I; Spicer, W E; Kapitulnik, A [Stanford Electronics Labs. and Dept. of Applied Physics, Stanford Univ., CA (USA)

1989-12-01

Angle-resolved photoemission experiments on single crystals of Bi{sub 2}(Sr,Ca,La){sub 3}Cu{sub 2}O{sub 8} are reported. The data show a dispersionless behaviour of the valence band states as a function of the perpendicular component of the wave vector (along the c-axis), while as a function of the parallel component (in the a-b plane) clear dispersion occurs. Furthermore, polarization-dependent excitations reveal information on the symmetry of the unoccupied states. (orig.).

Valence-band and core-level photoemission study of single-crystal Bi2CaSr2Cu2O8 superconductors

International Nuclear Information System (INIS)

Shen, Z.; Lindberg, P.A.P.; Wells, B.O.; Mitzi, D.B.; Lindau, I.; Spicer, W.E.; Kapitulnik, A.

1988-01-01

High-quality single crystals of Bi 2 CaSr 2 Cu 2 O 8 superconductors have been prepared and cleaved in ultrahigh vacuum. Low-energy electron diffraction measurements show that the surface structure is consistent with the bulk crystal structure. Ultraviolet photoemission and x-ray photoemission experiments were performed on these well-characterized sample surfaces. The valence-band and the core-level spectra obtained from the single-crystal surfaces are in agreement with spectra recorded from polycrystalline samples, justifying earlier results from polycrystalline samples. Cu satellites are observed both in the valence band and Cu 2p core level, signaling the strong correlation among the Cu 3d electrons. The O 1s core-level data exhibit a sharp, single peak at 529-eV binding energy without any clear satellite structures

Optimization of 90Sr/89Sr measurements

Directory of Open Access Journals (Sweden)

Legarda F.

2012-04-01

Full Text Available One of the key points in the double measurement method for the measurement of both, 89Sr and 90Sr, by using a proportional counter is the choice of the times at which the measurements should be done. In this paper, the formulae to calculate the 89Sr and 90Sr detection limits in conditions of radioactive equilibrium between 90Y and 90Sr are derived, and an analysis of them as a function of the time between the two measurements is done. The choice for the time of the second measurement is going to depend on the desired quality of the results to be obtained.

Switchable diode effect in oxygen vacancy-modulated SrTiO{sub 3} single crystal

Energy Technology Data Exchange (ETDEWEB)

Pan, Xinqiang; Shuai, Yao; Wu, Chuangui; Luo, Wenbo; Sun, Xiangyu; Zeng, Huizhong; Bai, Xiaoyuan; Gong, Chaoguan; Jian, Ke; Zhang, Wanli [University of Electronic Science and Technology of China, State Key Laboratory of Electronic Thin Films and Integrated Devices, Chengdu (China); Zhang, Lu; Guo, Hongliang [University of Electronic Science and Technology of China, The Center for Robotics, Chengdu (China); Tian, Benlang [26th Institute of China Electronics Technology Group Corporation, Chongqing (China)

2017-09-15

SrTiO{sub 3} (STO) single crystal wafer was annealed in vacuum, and co-planar metal-insulator-metal structure of Pt/Ti/STO/Ti/Pt were formed by sputtering Pt/Ti electrodes onto the surface of STO after annealing. The forming-free resistive switching behavior with self-compliance property was observed in the sample. The sample showed switchable diode effect, which is explained by a simple model that redistribution of oxygen vacancies (OVs) under the external electric field results in the formation of n-n{sup +} junction or n{sup +}-n junction (n donated n-type semiconductor; n{sup +} donated heavily doped n-type semiconductor). The self-compliance property is also interpreted by the formation of n-n{sup +}/n{sup +}-n junction caused by the migration of the OVs under the electric field. (orig.)

Contributions of conduction band offset to the enhanced separation efficiency of photoinduced charges for SrTiO3/Bi2O3 heterojunction semiconductor

International Nuclear Information System (INIS)

Zhang, Zhenlong; Zhu, Jichun; Li, Shengjun; Mao, Yanli

2014-01-01

SrTiO 3 /Bi 2 O 3 heterojunction semiconductor was prepared and characterized by X-ray diffraction, UV–vis absorption spectrum, and scanning electron microscope, surface photovoltage spectroscopy, and photoluminescence spectroscopy. The surface photovoltage spectra indicate that the separation efficiency of photoinduced charges for SrTiO 3 /Bi 2 O 3 was enhanced compared with that of SrTiO 3 or Bi 2 O 3 . The energy band diagram of SrTiO 3 /Bi 2 O 3 heterojunction was directly determined with X-ray photoelectron spectroscopy, and the conduction band offset between SrTiO 3 and Bi 2 O 3 was quantified to be 0.28±0.03 eV. The photoluminescence spectra display that the recombination rate of photoinduced carriers for SrTiO 3 /Bi 2 O 3 decreases compared with that of SrTiO 3 or Bi 2 O 3 , which is mainly due to the energy levels matching between them. Therefore the enhanced separation efficiency of photoinduced charges is resulting from the energy difference between the conduction band edges of SrTiO 3 and Bi 2 O 3 . -- Graphical abstract: Enhanced separation efficiency for SrTiO 3 /Bi 2 O 3 is resulting from the energy difference between the conduction band edges. Highlights: ●Heterojunction semiconductor of SrTiO 3 /Bi 2 O 3 was prepared. ●SrTiO 3 /Bi 2 O 3 presents enhanced separation efficiency. ●Conduction band offset between SrTiO 3 and Bi 2 O 3 is quantified. ●Recombination rate of SrTiO 3 /Bi 2 O 3 decreases compared with single phases

The dehydration of SrTeO3(H2O)--a topotactic reaction for preparation of the new metastable strontium oxotellurate(IV) phase ε-SrTeO3.

Science.gov (United States)

Stöger, Berthold; Weil, Matthias; Baran, Enrique J; González-Baró, Ana C; Malo, Sylvie; Rueff, Jean Michel; Petit, Sebastien; Lepetit, Marie Bernadette; Raveau, Bernard; Barrier, Nicolas

2011-05-28

Microcrystalline single-phase strontium oxotellurate(IV) monohydrate, SrTeO(3)(H(2)O), was obtained by microwave-assisted hydrothermal synthesis under alkaline conditions at 180 °C for 30 min. A temperature of 220 °C and longer reaction times led to single crystal growth of this material. The crystal structure of SrTeO(3)(H(2)O) was determined from single crystal X-ray diffraction data: P2(1)/c, Z = 4, a = 7.7669(5), b = 7.1739(4), c = 8.3311(5) Å, β = 107.210(1)°, V = 443.42(5) Å(3), 1403 structure factors, 63 parameters, R[F(2)>2σ(F(2))] = 0.0208, wR(F(2) all) = 0.0516, S = 1.031. SrTeO(3)(H(2)O) is isotypic with the homologous BaTeO(3)(H(2)O) and is characterised by a layered assembly parallel to (100) of edge-sharing [SrO(6)(H(2)O)] polyhedra capped on each side of the layer by trigonal-prismatic [TeO(3)] units. The cohesion of the structure is accomplished by moderate O-H···O hydrogen bonding interactions between donor water molecules and acceptor O atoms of adjacent layers. In a topochemical reaction, SrTeO(3)(H(2)O) condensates above 150 °C to the metastable phase ε-SrTeO(3) and transforms upon further heating to δ-SrTeO(3). The crystal structure of ε-SrTeO(3), the fifth known polymorph of this composition, was determined from combined electron microscopy and laboratory X-ray powder diffraction studies: P2(1)/c, Z = 4, a = 6.7759(1), b = 7.2188(1), c = 8.6773(2) Å, β = 126.4980(7)°, V = 341.20(18) Å(3), R(Fobs) = 0.0166, R(Bobs) = 0.0318, Rwp = 0.0733, Goof = 1.38. The structure of ε-SrTeO(3) shows the same basic set-up as SrTeO(3)(H(2)O), but the layered arrangement of the hydrous phase transforms into a framework structure after elimination of water. The structural studies of SrTeO(3)(H(2)O) and ε-SrTeO(3) are complemented by thermal analysis and vibrational spectroscopic measurements.

Single-phase ceramics with La{sub 1-x}Sr{sub x}Ga{sub 1-y}Mg{sub y}O{sub 3-{delta}} composition from precursors obtained by mechanosynthesis

Energy Technology Data Exchange (ETDEWEB)

Moure, A.; Tartaj, J.; Moure, C. [Instituto de Ceramica y Vidrio, CSIC, C/Kelsen 5, 28049 Madrid (Spain); Castro, A. [Instituto de Ciencia de Materiales de Madrid, CSIC, c/Sor Juana Ines de la Cruz, 3 Cantoblanco, 28049 Madrid (Spain)

2009-03-15

Dense ceramics with La{sub 0.80}Sr{sub 0.20}Ga{sub 0.85}Mg{sub 0.15}O{sub 2.825} and La{sub 0.80}Sr{sub 0.15}Ga{sub 0.85}Mg{sub 0.20}O{sub 2.825} compositions have been prepared by sintering of mechanosynthesized precursors. The perovskite is synthesized after 85 h of milling in a planetary mill. Single phases have been obtained at conditions that are not possible if traditional solid-state reaction (SSR) method is used. The influence of milling time and composition in the reactivity of the precursors is studied. Highest purity is obtained in Sr = 0.15 and Mg = 0.20 composition, with relative density higher than 97%. The total elimination of typical secondary phases for these compositions, as SrLaGaO{sub 4} and SrLaGa{sub 3}O{sub 7}, allows the total conductivity of the ceramics to be improved. The influence of the grain size and the nature of the grain boundaries on the electrical characteristic of the ceramics are also discussed. (author)

Electronic properties and surface reactivity of SrO-terminated SrTiO3 and SrO-terminated iron-doped SrTiO3.

Science.gov (United States)

Staykov, Aleksandar; Tellez, Helena; Druce, John; Wu, Ji; Ishihara, Tatsumi; Kilner, John

2018-01-01

Surface reactivity and near-surface electronic properties of SrO-terminated SrTiO 3 and iron doped SrTiO 3 were studied with first principle methods. We have investigated the density of states (DOS) of bulk SrTiO 3 and compared it to DOS of iron-doped SrTiO 3 with different oxidation states of iron corresponding to varying oxygen vacancy content within the bulk material. The obtained bulk DOS was compared to near-surface DOS, i.e. surface states, for both SrO-terminated surface of SrTiO 3 and iron-doped SrTiO 3 . Electron density plots and electron density distribution through the entire slab models were investigated in order to understand the origin of surface electrons that can participate in oxygen reduction reaction. Furthermore, we have compared oxygen reduction reactions at elevated temperatures for SrO surfaces with and without oxygen vacancies. Our calculations demonstrate that the conduction band, which is formed mainly by the d-states of Ti, and Fe-induced states within the band gap of SrTiO 3 , are accessible only on TiO 2 terminated SrTiO 3 surface while the SrO-terminated surface introduces a tunneling barrier for the electrons populating the conductance band. First principle molecular dynamics demonstrated that at elevated temperatures the surface oxygen vacancies are essential for the oxygen reduction reaction.

Study on absorption, accumulation and distribution of 90Sr in yellow-feather broiler

International Nuclear Information System (INIS)

Shang Zhaorong; Xu Shiming; Zhao Wenhu; Hou Lanxin

1993-04-01

The feeding experiment was carried out for yellow-feather broiler with 90 Sr(NO 3 ) 2 having activities of 1.85 x 10 0 ∼ 1.85 x 10 4 Bq/chicken to observe the regular pattern of absorption and distribution of 90 Sr in its organs and tissues. The results are as follows: The absorption rate of 90 Sr by oral feeding is very low. The most of 90 Sr is drained away by daily excreta from the body. The half-time of its feeding is within 24 hours. The accumulated dose varies with the time and different feeding methods. The more 90 Sr is fed, the more 90 Sr is absorbed, however, the uptake rate of 90 Sr is decreasing. The distribution of 90 Sr for bone is very strong and the partition ratio is about 90%. The absorption coefficient of 90 Sr in organs and tissues of broiler is presented

Muscle Glycogen Content Modifies SR Ca2 + Release Rate in Elite Endurance Athletes

DEFF Research Database (Denmark)

Gejl, Kasper Degn; Hvid, Lars G; Frandsen, Ulrik

2014-01-01

The aim of the present study was to investigate the influence of muscle glycogen content on sarcoplasmic reticulum (SR) function and peak power output (Wpeak) in elite endurance athletes.......The aim of the present study was to investigate the influence of muscle glycogen content on sarcoplasmic reticulum (SR) function and peak power output (Wpeak) in elite endurance athletes....

The selective separation of Cs and Sr ion on the inorganic ion-exchanger zeolites

Energy Technology Data Exchange (ETDEWEB)

Park, Hun Hwee; Min, Byeog Heon [Hoseo University, Taegu (Korea)

1998-04-01

This study shows the selective separation of Cs and Sr ion on the inorganic ion-exchanger zeolites such as clinoptilolite, Y-type CBV760, CBV780 and A-type 3A. The selective separation of Cs and Sr on these zeolites was examined using batch and continuous column experiments. For the selective separation of Cs and Sr from a synthetic wastewater, adsorption rate of Cs increased in the order, clinoptilolite> 3A>> CBV760> CBV780, adsorption rate of Sr increased in the other, 3A>> clinoptilolite> CBV760> CBV780. For the clinoptilolite, the adsorption rate of Cs reached about 96 {approx} 98% within 3h. The adsorption rate of Sr on 3A reached about 99% within 3h. (author). 40 refs., 27 figs., 4 tabs.

Decay of 83Sr

International Nuclear Information System (INIS)

Yu Xiaohan; Shi Shuanghui; Gu Jiahui

1997-01-01

The decay of 83 Sr was reinvestigated using γ singles and γ-γ-t coincidence measurement. A new level scheme of Rb, which contains 41 excited levels and about 180 transitions, is constructed. 19 new levels were added to the old level scheme and 8 formerly adopted levels were denied. A new data set of branching ratio, log(ft) value and spin parity was obtained

Photoluminescent properties of Sr2CeO4: Eu3+ and Sr2CeO4: Eu2+ phosphors suitable for near ultraviolet excitation

International Nuclear Information System (INIS)

Suresh, K.; Poornachandra Rao, N.V.; Murthy, K.V.R.

2014-01-01

Powder phosphors of 1 mol% Eu 3+ - and Eu 2+ -doped strontium cerium oxide (Sr 2 CeO 4 ) were synthesized by standard solid-state reaction method. Eu 3+ - and Eu 2+ -doped Sr 2 CeO 4 phosphors fired at 1100 ℃ for 2 h were analysed by X-ray diffraction (XRD) and photoluminescence (PL) techniques. The XRD patterns confirm that the obtained phosphors are a single phase of Sr 2 CeO 4 composed of orthorhombic structure. Room temperature PL excitation spectrum of air-heated Sr 2 CeO 4 : Eu phosphor has exhibited bands at 260, 280 and 350 nm. Whereas the excitation spectrum of Sr 2 CeO 4 : Eu phosphor heated under reducing (carbon) atmosphere exhibited single broadband range from 260 to 390 nm. The (PL) emission peaks of both the phosphors at 467 (blue), 537 (green) and 616 nm (red) generate white light under 260, 280 and 350 nm excitation wavelengths. The Commission International de l'Eclairage (CIE) colour coordinates conforms that these phosphors emitting white light. The results reveal that these phosphors are multifunctional phosphors which emit white light under these excitations that they could be used as white components for display and lamp devices and as well as possible good light-conversion phosphor LEDs under near-ultraviolet (nUV) chip. (author)

Magnetic and electronic properties of SrMnO3 thin films

Science.gov (United States)

Mandal, Arup Kumar; Panchal, Gyanendra; Choudhary, R. J.; Phase, D. M.

2018-05-01

Single phase hexagonal bulk SrMnO3 (SMO) was prepared by solid state route and it was used for depositing thin films by pulsed laser deposition (PLD) technique on single crystalline (100) oriented SrTiO3 (STO) substrate. X-ray diffraction shows that the thin film is deposited in cubic SrMnO3 phase. From X-ray absorption at the Mn L edge we observed the mixed valency of Mn (Mn3+& Mn4+) due to strain induced by the lattice mismatching between SMO and STO. Due to this mixed valency of Mn ion in SMO film, the ferromagnetic nature is observed at lower temperature because of double exchange. After post annealing with very low oxygen partial pressure, magnetic and electronic property of SMO films are effectively modified.

Temporal dynamics of high repetition rate pulsed single longitudinal ...

Indian Academy of Sciences (India)

ing (GIG) cavity, single-mode dye laser pumped by high repetition rate ... in a high loss cavity, a detailed theoretical study and optimization of cavity ..... rate for high conversion efficiency and longer pulse width of the single-mode dye laser.

Structural study of intermediate phase in layered perovskite SrBi sub 2 Ta sub 2 O sub 9 single crystal

CERN Document Server

Onodera, A; Yamashita, H

2003-01-01

The crystal structure of an intermediate phase of Bi-layered ferroelectric SrBi sub 2 Ta sub 2 O sub 9 single crystals was studied by means of X-ray diffraction. An analysis of the extinction rules and X-ray intensities demonstrated that the crystal structure is orthorhombic with space group A2 sub 1 am in the ferroelectric phase and Amam in the intermediate phase; this conclusion is in good agreement with the findings of previous powder neutron diffraction studies.

Evidence for core-coupled states in 87Y from a 89Y(p, t)87Y and 88Sr(p, t)86Sr comparison

International Nuclear Information System (INIS)

Oelrich, I.C.; Krien, K.; DelVecchio, R.M.; Naumann, R.A.

1976-01-01

The 89 Y(p, t) 87 Y and 88 Sr(p, t) 86 Sr reactions were studied at 42 MeV proton energy, using a quadrupole-dipole-dipole-dipole spectograph. Comparison of excitation energies, (p, t) cross section strengths and angular distribution shapes indicates that basis features of the core-coupling model apply to these nuclei. However, mixing of single particle states with the core-coupled states is evident. The (p, t) cross-section strength summed over the 87 Y multiplet is found with few exceptions to be nearly a constant multiple of the (p, t) strength of the associated 86 Sr state

Deposition of 90Sr in bone and the relevant dose

International Nuclear Information System (INIS)

Kawamura, Hisao

1976-01-01

The deposition of fallout 90 Sr in bone and radiation dose from the nuclide in Japan is reviewed with special reference to (i) the intraskeletal distribution of 90 Sr and reference bone, (ii) bone models for predicting 90 Sr level and (iii) possible problems in applying dose rate factors to Japanese, especially to infants and adolescents. An evidence is presented for the assumption that the ratio of the 90 Sr concentration in a particular bone to that in vertebra will reach the ratio observed for stable strontium under the virtually constant intake of 90 Sr. The importance of surveying 90 Sr levels in different bones is stressed. Observed Ratios (bone/diet) found for Japanese are noticeably lower than those reported for Europeans and Americans. The recently presented model for the retention of alkaline earth elements in man by ICRP will be useful if only adults are concerned. Dose rate factors for 90 Sr in bone should be given as a function of age for the purpose of better estimation of dose commitments. The cumulative absorbed doses to bone tissues calculated with the Palmley-Mays model and with the Spiers model show remarkably higher levels in school children and young adults than the mean level. (auth.)

Evaluating 90Sr and 137Cs accumulation by structural elements of exclusion zone's vegetative communities of meadow and lea land

International Nuclear Information System (INIS)

Paskevich, S.A.; Petrov, M.F.

2003-01-01

Biogenic carry-over of 90 Sr and 137 Cs by structural elements of exclusion zone's meadows and lea land phytocenosis is considered. Quantitative parameters of radionuclide accumulation are evaluated in substrate and live biomass of communities growing under various ecological conditions. It was stated that accumulation levels for ground biomass of communities depends, at a significant rate, on landscape growing conditions. These values fluctuate within the range of around 100 times. For 90 Sr, significantly lower difference in carry-over values was observed totaling up to 5 times, although for single community, this radionuclide carry-over exceeds essentially 137 Cs carry-over

Applicability of 87Sr/86Sr in examining return flow of irrigation water in highly agricultural watersheds in Japan

Science.gov (United States)

Yoshida, T.; Nakano, T.; Shin, K. C.; Tsuchihara, T.; Miyazu, S.; Kubota, T.

2017-12-01

Water flows in watersheds containing extensive areas of irrigated paddies are complex because of the substantial volumes involved and the repeated cycles of water diversion from, and return to, streams. For better management of low-flow conditions, numerous studies have attempted to quantify the return flow using the stable isotopes of water; however, the temporal variation in these isotopic compositions due to fractionation during evaporation from water surfaces hinders their application to watersheds with extensive irrigated paddies. In this study, we tested the applicability of the strontium isotopes (87Sr/86Sr, hereafter Sr ratio) for studying hydrological processes in a typical agricultural watershed located on the alluvial fan of the Kinu River, namely the Gogyo River, in central Japan. The Sr ratio of water changes only because of interactions with the porous media it flows through, or because of mixing with water that has different Sr ratios. We sampled water both at a single rice paddy, and on the watershed scale in the irrigated and non-irrigated periods. The soil water under the paddy decreased as sampling depth increased, and the soil water at a depth of 1.5 m showed a similar Sr ratio to the spring. The water sampled in the drainage channel with a concrete lined bottom showed a similar Sr ratio to the irrigation water, whereas that with a soil bottom was plotted between the plots of the irrigation water and shallow aquifer. These results suggest the Sr ratio decreases as it mixes with the soil water through percolation; whereas the Sr ratio will be less likely to change when water drains from paddies via surface pathways. The streamflow samples were plotted linearly on the Sr ratio and 1/Sr plot, indicating that the streamflow was composed of two end-members; the irrigation water and the shallow aquifer. The continuous decline in the Sr ratio along the stream suggests an exfiltration of water from the shallow aquifers. The stream water during the non

[Ag25(SR)18]¯: The ‘Golden’ Silver Nanoparticle

KAUST Repository

Joshi, Chakra Prasad

2015-08-31

Silver nanoparticles with an atomically precise molecular formula [Ag25(SR)18]¯ (‒SR: thiolate) are synthesized and their single-crystal structure is determined. This synthesized nanocluster is the only silver nanoparticle that has a virtually identical analogue in gold, i.e., [Au25(SR)18]¯, in terms of number of metal atoms, ligand count, super-atom electronic configuration, and atomic arrangement. Furthermore, both [Ag25(SR)18]¯ and its gold analogue share a number of features in their optical absorption spectra. This unprecedented molecular synthesis in silver to mimic gold offers the first model nanoparticle platform to investigate the centuries-old problem of understanding the fundamental differences between silver and gold in terms of nobility, catalytic activity, and optical property.

[Ag25(SR)18]¯: The ‘Golden’ Silver Nanoparticle

KAUST Repository

Joshi, Chakra Prasad; Bootharaju, Megalamane Siddaramappa; Alhilaly, Mohammad J.; Bakr, Osman

2015-01-01

Silver nanoparticles with an atomically precise molecular formula [Ag25(SR)18]¯ (‒SR: thiolate) are synthesized and their single-crystal structure is determined. This synthesized nanocluster is the only silver nanoparticle that has a virtually identical analogue in gold, i.e., [Au25(SR)18]¯, in terms of number of metal atoms, ligand count, super-atom electronic configuration, and atomic arrangement. Furthermore, both [Ag25(SR)18]¯ and its gold analogue share a number of features in their optical absorption spectra. This unprecedented molecular synthesis in silver to mimic gold offers the first model nanoparticle platform to investigate the centuries-old problem of understanding the fundamental differences between silver and gold in terms of nobility, catalytic activity, and optical property.

Colour relations for Mira and Semiregular (SR) type stars

International Nuclear Information System (INIS)

Guney, Yavuz; Yesilyaprak, Cahit

2016-01-01

In this study, the period-colour relations, the colour-colour relations and the effective temperature were examined for Semiregular (SR) and Mira type variable stars. SR variables show an obvious period-colour relations, especially in infrared (IR). There are differences between SR and Mira type variable stars with respect to their colour relations. It has been thought that these differencies are caused by their mass loss rates and their effective temperatures. (paper)

Quantum Logic with Composite Pulse Sequences on Sr^+

Science.gov (United States)

Shewmon, Ruth; Labaziewicz, Jaroslaw; Ge, Yufei; Wang, Shannon; Chuang, Isaac L.

2008-03-01

The optical 5S1/2->4D1/2 transition in Sr^+ is an attractive qubit because it can be addressed by diode lasers, which are relatively inexpensive and easy to operate. We characterize single-qubit rotations as well as a CNOT gate on a Sr^+ ion in a surface electrode Paul trap. To improve these operations, the frequency of the clock laser is stabilized to a high-finesse optical cavity. The resulting linewidth of the laser is approximately 300Hz. Composite pulse sequences, a technique adapted from NMR, have been shown to reduce the effects of systematic errors in a variety of quantum systems. We demonstrate several composite sequences that improve the fidelity of quantum logic operations on Sr^+.

Kinetics of distribution of 90Sr in Beijing-white layers

International Nuclear Information System (INIS)

Shang Zhaorong; Xu Shiming; Zhao Wenhu; Hou Lanxin

1993-08-01

The experiment feeding 90 Sr(NO 3 ) 2 in the range of 1.85 x 10 2 to 1.85 x 10 5 Bq/chicken was carried out with 45 Beijing-white layers to observe the regular pattern of absorption and distribution of 90 Sr in organs and tissues. The results are summarized as follows: the uptake rate of 90 Sr by layer through oral feeding is very low. Most part of 90 Sr drains away from body with daily excreta and egg. The accumulation of 90 Sr in the body is low and about 70% is in the bone. About 99% of 90 Sr in egg is concentrated in the eggshell. The order of absorptivity of 90 Sr in tissues is bone>feather>muscle>blood>viscera. The absorption coefficient of 90 Sr in organs and tissues in different stages with different feeding volumes has been calculated

Emergence of superconductivity in topological insulator Bi{sub 2}Se{sub 3} by Sr intercalation

Energy Technology Data Exchange (ETDEWEB)

Shruti,; Maurya, V. K.; Srivastava, P.; Patnaik, S., E-mail: spatnaik@mail.jnu.ac.in [School of Physical Sciences, Jawaharlal Nehru University, New Delhi-110067 (India)

2016-05-23

Recently superconductivity wasreported by Sr intercalation in topological insulator Bi{sub 2}Se{sub 3}. In this report we extensively study anisotropic superconducting properties of Sr{sub 0.1}Bi{sub 2}Se{sub 3} with transition at ~2.9 through resistivity and DC magnetization measurement. We also discuss synthesis methodology for growth of single crystal Sr-Bi{sub 2}Se{sub 3}. The anisotropic properties of Sr{sub 0.1}Bi{sub 2}Se{sub 3} single crystals were studied using transport measurements. Using Ginzburg Landau formulas the upper critical field H{sub c2}(0) comes out to be 2.1 T and 1.4 T for magnetic field applied along the ab-plane and c-axis of the single crystalsand corresponding Ginzburg - Landau coherence lengths are ξ{sub ab} = 15.3 nm and ξ{sub c} = 10.2 nm. The sample shows weak electronic anisotropy Γ = 1.5. Hall resistivity is linear with field at 10 K.

How to orient the functional GroEL-SR1 mutant for atomic force microscopy investigations

International Nuclear Information System (INIS)

Schiener, Jens; Witt, Susanne; Hayer-Hartl, Manajit; Guckenberger, Reinhard

2005-01-01

We present high-resolution atomic force microscopy (AFM) imaging of the single-ring mutant of the chaperonin GroEL (SR-EL) from Escherichia coli in buffer solution. The native GroEL is generally unsuitable for AFM scanning as it is easily being bisected by forces exerted by the AFM tip. The single-ring mutant of GroEL with its simplified composition, but unaltered capability of binding substrates and the co-chaperone GroES, is a more suited system for AFM studies. We worked out a scheme to systematically investigate both the apical and the equatorial faces of SR-EL, as it binds in a preferred orientation to hydrophilic mica and hydrophobic highly ordered pyrolytic graphite. High-resolution topographical imaging and the interaction of the co-chaperone GroES were used to assign the orientations of SR-EL in comparison with the physically bisected GroEL. The usage of SR-EL facilitates single molecule studies on the folding cycle of the GroE system using AFM

Decoupling of magnetism and electric transport in single-crystal (Sr1‑x A x )2IrO4 (A  =  Ca or Ba)

Science.gov (United States)

Zhao, H. D.; Terzic, J.; Zheng, H.; Ni, Y. F.; Zhang, Y.; Ye, Feng; Schlottmann, P.; Cao, G.

2018-06-01

We report a systematical structural, transport and magnetic study of Ca or Ba doped Sr2IrO4 single crystals. Isoelectronically substituting Ca2+ (up to 15%) or Ba2+ (up to 4%) ion for the Sr2+ ion provides no additional charge carriers but effectively changes the lattice parameters in Sr2IrO4. In particular, 15% Ca doping considerably reduces the c-axis and the unit cell by nearly 0.45% and 1.00%, respectively. These significant, anisotropic compressions in the lattice parameters conspicuously cause no change in the Néel temperature which remains at 240 K, but drastically reduces the electrical resistivity by up to five orders of magnitude or even precipitates a sharp insulator-to-metal transition at lower temperatures, i.e. the vanishing insulating state accompanies an unchanged Néel temperature in (Sr1‑x A x )2IrO4. This observation brings to light an intriguing difference between chemical pressure and applied pressure, the latter of which does suppress the long-range magnetic order in Sr2IrO4. This difference reveals the importance of the Ir1–O2–Ir1 bond angle and homogenous volume compression in determining the magnetic ground state. All results, along with a comparison drawn with results of Tb and La doped Sr2IrO4, underscore that the magnetic transition plays a nonessential role in the formation of the charge gap in the spin–orbit-tuned iridate.

Vertical migration of 85Sr, 137Cs and 131I in various arable and undisturbed soils

International Nuclear Information System (INIS)

Palagyi, S.; Palagyiova, J.

2003-01-01

The vertical migration of 85 Sr, 137 Cs and 131 I in some arable and undisturbed single-contaminated soils was studied by gamma-spectrometry measurements under lysimetric laboratory conditions during irrigation of the soil profiles with wet atmospheric precipitation for about one year, except 131 I. A new simple exponential compartment (box) model was derived, which makes it possible to calculate the migration rate constants and migration rates in the individual soil layers (vertical sections) as well as the total vertical migration rate constants and total vertical migration rates of radionuclides in the bulk soil horizon. The relaxation times of radionuclides in respective soil horizons can also be evaluated. (author)

The adsorption of Sr(II) and Cs(I) ions by irradiated Saccharomyces cerevisiae

International Nuclear Information System (INIS)

Yiming Tan; Jundong Feng; Liang Qiu; Zhentian Zhao; Xiaohong Zhang; Haiqian Zhang

2017-01-01

Adsorption behavior and mechanism of Sr(II) and Cs(I) in single and binary solutions using irradiated Saccharomyces cerevisiae was investigated. The effects of several environmental factors on Sr(II) and Cs(I) adsorption to irradiated Saccharomyces cerevisiae was determined. The equilibrium experimental data were simulated by different kinetic models and isotherm models. The combined effect of Sr(II) and Cs(I) on Saccharomyces cerevisiae is generally antagonistic. SEM and EDS analyses indicate that crystals formed on the cell surface are precipitate of Sr(II) and Cs(I), respectively. (author)

Growth and properties of oxygen- and ion-doped Bi2Sr2CaCu2O8+δ single crystals

Science.gov (United States)

Mitzi, D. B.; Lombardo, L. W.; Kapitulnik, A.; Laderman, S. S.; Jacowitz, R. D.

1990-04-01

A directional solidification method for growing large single crystals in the Bi2Sr2CaCu2O8+δ system is reported. Ion doping, with replacement of La for Sr and Y for Ca, as well as oxygen doping in these crystals has been explored. Doped and undoped crystals have been characterized using microprobe analysis, x-ray diffraction, thermogravimetric analysis, and magnetic and Hall measurements. Ion doping results in little change of the superconducting transition for substitution levels below 20-25%, while beyond this level the Meissner signal broadens and the low-temperature Meissner signal decreases. Microprobe analysis and x-ray diffraction performed on these more highly substituted single crystals provide evidence for inhomogeneity and phase segregation into regions of distinct composition. Annealing unsubstituted crystals in increasing partial pressures of oxygen reversibly depresses the superconducting transition temperature from 90 (as made) to 77 K (oxygen pressure annealed), while the carrier concentrations, as determined from Hall effect measurements, increase from n=3.1(3)×1021 cm-3 (0.34 holes per Cu site) to 4.6(3)×1021 cm-3 (0.50 holes per Cu site). No degradation of the Meissner transition or other indications of inhomogeneity or phase segregation with doping are noted, suggesting that oxygen-doped Bi2Sr2CaCu2O8+δ is a suitable system for pursuing doping studies. The decrease in Tc with concentration for 0.34<=n<=0.50 indicates that a high-carrier-concentration regime exists in which Tc decreases with n and suggests that this decrease does not arise from material inhomogeneity or other materials problems. An examination of the variation of Tc with the density of states and lattice constants for all of the doped and undoped superconducting samples considered here indicates that changes in Tc with doping are primarily affected by changes in the density of states (or carrier concentration) rather than by structural variation induced by the doping.

Reactive Coevaporation Synthesis and Characterization of SrTiO3 Thin Films

Science.gov (United States)

Yamaguchi, Hiromu; Matsubara, Shogo; Miyasaka, Yoichi

1991-09-01

SrTiO3 thin films were prepared by the reactive coevaporation method, where the Ti and Sr metals were evaporated in oxygen ambient with an E-gun and K-cell, respectively. A uniform depth profile in composition was achieved by altering the Ti evaporation rate according to the Sr evaporation rate change. A typical dielectric constant of 170 was measured on films of 75 nm in thickness. The in-situ annealing in oxygen plasma reduced the leakage current.

The ternary post-transition metal carbodiimide SrZn(NCN)2

International Nuclear Information System (INIS)

Corkett, Alex J.; Konze, Philipp M.; Dronskowski, Richard

2017-01-01

SrZn(NCN) 2 , the first example of a ternary post-transition metal carbodiimide, was prepared by a solid-state metathesis reaction. The crystal structure was solved from PXRD data and found to adopt the orthorhombic (Cmcm) BaZnSO structure, a high symmetry modification of that expressed by the oxide analogue SrZnO 2 . Locally, SrZn(NCN) 2 features ZnN 4 tetrahedra and SrN 6 trigonal prisms similar to those in quarternary LiSr 2 M(NCN) 4 (M = Al 3+ and Ga 3+ ) phases, however, the overall topologies are distinct with single chains in the former and double chains in the latter. Electronic structure calculations indicate an indirect bandgap of about 2.95 eV in SrZn(NCN) 2 , slightly lower than the experimentally observed bandgap of 3.4 eV in SrZnO 2 and consistent with a greater degree of covalency. The structural similarities between SrZn(NCN) 2 and oxychalcogenide analogues highlight the pseudochalcogenide character of NCN 2- and suggest that the title compound may serve as a template for accessing novel ternary carbodiimides featuring tetrahedrally coordinated transition metals. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The effects of secondary mineral precipitates on {sup 90}Sr mobility at the Hanford Site, USA

Energy Technology Data Exchange (ETDEWEB)

Um, Wooyong [Pacific Northwest National Laboratory, 902 Battelle Blvd., MSIN P7-54, Richland, WA 99354 (United States); Division of Advanced Nuclear Engineering, Pohang University of Science and Technology - POSTECH (Korea, Republic of); Wang, Guohui; Serne, R. Jeffrey [Pacific Northwest National Laboratory, 902 Battelle Blvd., MSIN P7-54, Richland, WA 99354 (United States)

2013-07-01

The effects of secondary precipitates on {sup 90}Sr transport at the Hanford Site were investigated using quartz column experiments with simulated caustic tank waste leachates (STWL). Significantly enhanced retardation of Sr transport was observed in the column contacted with STWL due to Sr sorption and co-precipitation with neo-formed nitrate cancrinite. However, the column results also suggest that neo-formed secondary precipitates could behave like native mobile colloids that can enhance Sr transport. Initially immobilized Sr within secondary precipitates could re-mobilize given a change in the pore water background conditions. The mobility of the neo-formed Sr-bearing precipitates increased with increased solution flow rate. In the field, pore water contents and flow rates can be changed by snow-melt (or storm water) events or artificial infiltration. The increased pore water flow rate caused by these events could affect the mobility of {sup 90}Sr-containing secondary precipitates, which can be a potential source for facilitated Sr transport in Hanford Site subsurface environments. (authors)

High-pressure synthesis and crystal structures of the strontium oxogallates Sr2Ga2O5 and Sr5Ga6O14

Science.gov (United States)

Kahlenberg, Volker; Goettgens, Valerie; Mair, Philipp; Schmidmair, Daniela

2015-08-01

High-pressure synthesis experiments in a piston-cylinder apparatus at 1.5 GPa/3.0 GPa and 1000 °C resulted in the formation of single-crystals of Sr2Ga2O5 and Sr5Ga6O14, respectively. The structures of both compounds have been solved from single-crystal diffraction data sets using direct methods. The first compound is orthorhombic with space group type Pbca (a=10.0021(4) Å, b=9.601(4) Å, c=10.6700(4) Å, V=1024.6(4) Å3, Mr=394.68 u, Z=8, Dx=5.12 g/cm3) and belongs to the group of single layer gallates. Individual sheets are parallel to (0 0 1) and can be built from the condensation of unbranched vierer single chains running along [0 1 0]. The layers are characterized by the presence of four- and strongly elliptical eight-membered rings of corner connected tetrahedra in UUDD and UUUUDDDD conformation. Strontium atoms are sandwiched between the tetrahedral layers for charge compensation and are coordinated by six and seven oxygen ligands, respectively. Sr2Ga2O5 is isotypic with several other double sulfides and selenides. To the best of our knowledge, it is the first example of an oxide with this structure type. From a structural point of view, Sr5Ga6O14 is a phyllogallate as well. The crystal structure adopts the monoclinic space group P21/c (a=8.1426(3) Å, b=8.1803(3) Å, c=10.8755(4) Å, β=91.970(4)° V=723.98(5) Å3, Mr=1080.42 u, Z=2, Dx=4.96 g/cm3). Individual sheets extend along (0 0 1). Basic building units are unbranched dreier single chains parallel to [1 0 0]. The layers contain tertiary (Q3) und quaternary (Q4) connected [GaO4]-tetrahedra in the ratio 2:1 resulting in a Ga:O ratio of 3:7 and the formation of exclusively five-membered rings. Linkage between adjacent tetrahedral sheets is provided by three symmetrically independent strontium ions which are surrounded by six to eight oxygen atoms. The layers in Sr5Ga6O14 are similar to those observed in the melilite structure-type. Crystallochemical relationships between the present phases and other

Crystal structures of KM(AsF6)3 (M2+ = Mg, Co, Mn, Zn), KCu(SbF6)3 and [Co(HF)2]Sr[Sr(HF)]2-[Sr(HF)2]2[AsF6]12

International Nuclear Information System (INIS)

Mazej, Zoran; Goreshnik, Evgeny

2015-01-01

The KM(AsF 6 ) 3 (M 2+ = Mg, Co, Mn, Zn) and KCu(SbF 6 ) 3 compounds crystallize isotypically to previously known KNi(AsF 6 ) 3 . The main features of the structure of these compounds are rings of MF 6 octahedra sharing apexes with AsF 6 octahedra connected into infinite tri-dimensional frameworks. In this arrangement cavities are formed where K + cations are placed. Single crystals of CoSr 5 (AsF 6 ) 12 .8HF were obtained as one of the products after the crystallization of 3KF/CoF 2 /SrF 2 mixture in the presence of AsF 5 in anhydrous HF. The CoSr 5 (AsF 6 ) 12 .8HF is monoclinic, C/2c (No.15), with a = 26.773(5) Aa, b = 10.087(2) Aa, c = 21.141(5) Aa, β = 93.296(13) circle , V = 5699.9(19) Aa 3 at 200 K, and Z = 4. There are three crystallographically non-equivalent Sr 2+ cations in the crystal structure of CoSr 5 (AsF 6 ) 12 .8HF. The Sr1 is coordinated by ten fluorine atoms from eight different [AsF 6 ]- anions, meanwhile Sr2 and Sr3 are bound to nine fluorine atoms provided by one HF and eight AsF 6 units or by two HF and six AsF 6 units, respectively. The Co 2+ is coordinated distorted-octahedrally by six fluorine atoms from two HF molecules and four different AsF 6 units. All those moieties in the crystal structure of [Co(HF) 2 ]Sr[Sr(HF)] 2 [Sr(HF) 2 ] 2 [AsF 6 ] 12 are connected into tridimensional framework. The CoSr 5 (AsF 6 ) 12 .8HF is a unique example of compound where HF molecules are directly bound via fluorine atoms to two different metal centres.

Incipient 2D Mott insulators in extreme high electron density, ultra-thin GdTiO3/SrTiO3/GdTiO3 quantum wells

Science.gov (United States)

Allen, S. James; Ouellette, Daniel G.; Moetakef, Pouya; Cain, Tyler; Chen, Ru; Balents, Leon; Stemmer, Susanne

2013-03-01

By reducing the number of SrO planes in a GdTiO3 /SrTiO3/ GdTiO3 quantum well heterostructure, an electron gas with ~ fixed 2D electron density can be driven close to the Mott metal insulator transition - a quantum critical point at ~1 electron per unit cell. A single interface between the Mott insulator GdTiO3 and band insulator SrTiO3 has been shown to introduce ~ 1/2 electron per interface unit cell. Two interfaces produce a quantum well with ~ 7 1014 cm-2 electrons: at the limit of a single SrO layer it may produce a 2D magnetic Mott insulator. We use temperature and frequency dependent (DC - 3eV) conductivity and temperature dependent magneto-transport to understand the relative importance of electron-electron interactions, electron-phonon interactions, and surface roughness scattering as the electron gas is compressed toward the quantum critical point. Terahertz time-domain and FTIR spectroscopies, measure the frequency dependent carrier mass and scattering rate, and the mid-IR polaron absorption as a function of quantum well thickness. At the extreme limit of a single SrO plane, we observe insulating behavior with an optical gap substantially less than that of the surrounding GdTiO3, suggesting a novel 2D Mott insulator. MURI program of the Army Research Office - Grant No. W911-NF-09-1-0398

High-pressure synthesis and crystal structures of the strontium oxogallates Sr{sub 2}Ga{sub 2}O{sub 5} and Sr{sub 5}Ga{sub 6}O{sub 14}

Energy Technology Data Exchange (ETDEWEB)

Kahlenberg, Volker, E-mail: volker.kahlenberg@uibk.ac.at [Institute of Mineralogy and Petrography, University of Innsbruck, Innrain 52, Innsbruck A-6020 (Austria); Goettgens, Valerie; Mair, Philipp; Schmidmair, Daniela [Institute of Mineralogy and Petrography, University of Innsbruck, Innrain 52, Innsbruck A-6020 (Austria)

2015-08-15

High-pressure synthesis experiments in a piston–cylinder apparatus at 1.5 GPa/3.0 GPa and 1000 °C resulted in the formation of single-crystals of Sr{sub 2}Ga{sub 2}O{sub 5} and Sr{sub 5}Ga{sub 6}O{sub 14}, respectively. The structures of both compounds have been solved from single-crystal diffraction data sets using direct methods. The first compound is orthorhombic with space group type Pbca (a=10.0021(4) Å, b=9.601(4) Å, c=10.6700(4) Å, V=1024.6(4) Å{sup 3}, M{sub r}=394.68 u, Z=8, D{sub x}=5.12 g/cm{sup 3}) and belongs to the group of single layer gallates. Individual sheets are parallel to (0 0 1) and can be built from the condensation of unbranched vierer single chains running along [0 1 0]. The layers are characterized by the presence of four- and strongly elliptical eight-membered rings of corner connected tetrahedra in UUDD and UUUUDDDD conformation. Strontium atoms are sandwiched between the tetrahedral layers for charge compensation and are coordinated by six and seven oxygen ligands, respectively. Sr{sub 2}Ga{sub 2}O{sub 5} is isotypic with several other double sulfides and selenides. To the best of our knowledge, it is the first example of an oxide with this structure type. From a structural point of view, Sr{sub 5}Ga{sub 6}O{sub 14} is a phyllogallate as well. The crystal structure adopts the monoclinic space group P2{sub 1}/c (a=8.1426(3) Å, b=8.1803(3) Å, c=10.8755(4) Å, β=91.970(4)° V=723.98(5) Å{sup 3}, M{sub r}=1080.42 u, Z=2, D{sub x}=4.96 g/cm{sup 3}). Individual sheets extend along (0 0 1). Basic building units are unbranched dreier single chains parallel to [1 0 0]. The layers contain tertiary (Q{sup 3}) und quaternary (Q{sup 4}) connected [GaO{sub 4}]-tetrahedra in the ratio 2:1 resulting in a Ga:O ratio of 3:7 and the formation of exclusively five-membered rings. Linkage between adjacent tetrahedral sheets is provided by three symmetrically independent strontium ions which are surrounded by six to eight oxygen atoms. The layers

Doping induced grain size reduction and photocatalytic performance enhancement of SrMoO{sub 4}:Bi{sup 3+}

Energy Technology Data Exchange (ETDEWEB)

Wang, Yunjian, E-mail: wangyunjianmail@163.com; Xu, Hui; Shao, Congying; Cao, Jing, E-mail: caojing@mail.ipc.ac.cn

2017-01-15

Graphical abstract: Photocatalytic performance of SrMoO{sub 4} was greatly improved by Bi{sup 3+} doping effects, including crystalline size reduction, band gap narrowing, and lattice contraction. - Highlights: • An efficient SrMoO{sub 4} photocatalyst was fabricated by Bi{sup 3+} doping under hydrothermal condition. • Bi{sup 3+} doping effects, including crystalline size reduction, band gap narrowing, and lattice contraction were discovered in SrMoO{sub 4} nanomaterials. • The photocatalytic activity was great improved on account of Bi{sup 3+} doping effects. • Photoluminescence studies found that hydroxyl radical (·OH) is the main active species in the photocatalytic degradation process. - Abstract: Ion doping is one of the most effective ways to develop photocatalysts by creating impurity levels in the energy band structure. In this paper, novel Bi{sup 3+} doped SrMoO{sub 4} (SrMoO{sub 4}:Bi{sup 3+}) nanocrystals were prepared by a simple hydrothermal method. By systematic characterizations using x-ray diffraction, infrared spectra, UV–vis spectra, X-ray photoelectron spectroscopy and transmission electron microscopy, it is demonstrated that all the samples crystallized in a single phase of scheelite structure, and particle sizes of SrMoO{sub 4}:Bi{sup 3+} gradually decreased. The Bi{sup 3+} doped nanoparticles showed lattice contraction, and band-gap narrowing. The photocatalytic activity of the samples was measured by monitoring the degradation of methylene blue dye in an aqueous solution under UV-radiation exposure. It is found that SrMoO{sub 4}:Bi{sup 3+} showed excellent activity toward photodegradation of methylene blue solution under UV light irradiation compared to the pure SrMoO{sub 4}. These observations are interpreted in terms of the Bi{sup 3+} doping effects and the increased the surface active sites, which results in the improved the ratio of surface charge carrier transfer rate and reduced the electron–hole recombination rate. These

μ+SR Investigation of the Shastry-Sutherland Compound SrCu2(BO3)2

Science.gov (United States)

Sassa, Y.; Wang, S.; Sugiyama, J.; Amato, A.; Rønnow, H. M.; Rüegg, C.; Månsson, M.

In this study we have investigated the low-dimensional correlated spin system SrCu2(BO3)2 using ambient-pressure muon spin rotation/relaxation (μ+SR). The zero-field data are similar to previously published data, but in addition, they give an even clearer sign of the two low-temperature transitions (T1 ≈ 3 and T2 ≈ 7 K), which is fully consistent with inelastic neutron scattering (INS) measurements. Longitudinal field (LF) data clearly show that the copper spins are highly dynamic and a saturation of the low-temperature relaxation rate indicate that these are indeed two-dimensional (2D) quantum spin fluctuations.

Losses of Sr/sup 90/, Sr/sup 89/, and I/sup 131/ from fallout-contaminated plants

Energy Technology Data Exchange (ETDEWEB)

Martin, W E

1964-11-01

During the early period following local fallout, and during periods of maximal worldwide fallout, the entry of radionuclides into terrestrial food-chains is due primarily to the external contamination of plants and secondarily to the uptake of radionuclides from contaminated soil. Studies were undertaken to estimate the rates of radionuclide loss from fallout-contaminated vegetation and hence from the diets of herbivores living in a fallout field. On the fifth, fifteenth, thirtieth, and sixtieth days after an underground nuclear explosion (Operation Sedan) at the Nevada Test Site, plant samples were collected from twenty representative locations in the fallout field and analyzed to determined the concentrations (pc/g dry wt) of /sup 90/Sr, /sup 89/Sr, and /sup 131/I at the times of collections. While the radioactive half lives of /sup 90/Sr, /sup 89/Sr, and /sup 131/I are approximately 27.7 years, 53 days, and 8.04 days respectively, their average effective half-lives on fallout-contaminated plants, during the period from 5 to 30 days after the detonation, were 27.8 days, 17.8 days, and 5.0 days respectively. Losses of /sup 90/Sr were attributed to radioactive decay and to the removal of fallout particles and foliage by wind and/or other mechanical disturbances. Losses of /sup 90/Sr and /sup 89/Sr were attributed to radioactive decay and to the removal of fallout particles and foliage by wind and/or other mechanical disturbances. Losses of /sup 131/I were attributed to radioactive decay, to mechanical disturbance, and to the vaporization of /sup 131/I from the fallout particles retained on foliage.

Zintl-phases with layer anions: preparation and crystal structures of the isotypic compounds SrSn sub 2 As sub 2 and Sr sub 0. 87 Ba sub 0. 13 Sn sub 2 As sub 2 and a single crystal structure determination of KSnSb. Zintl-Phasen mit Schichtanionen: Darstellung und Kristallstrukturen der isotypen Verbindungen SrSn sub 2 As sub 2 und Sr sub 0,87 Ba sub 0,13 Sn sub 2 As sub 2 sowie eine Einkristallstrukturbestimmung von KSnSb

Energy Technology Data Exchange (ETDEWEB)

Eisenmann, B; Klein, J [Abt. 2 fuer Anorganische Chemie, Technische Hochschule Darmstadt (Germany)

1991-06-01

The metallic reflecting compounds SrSn{sub 2}As{sub 2} and Sr{sub 0.87}Ba{sub 0.13}Sn{sub 2}As{sub 2} were prepared from the melt, they crystallize in the trigonal rhombohedral system (space group R3m, Z = 3) with lattice constants see ''Inhaltsuebersicht''. In the crystal structure of the isotypic compounds threebonded Sn atoms and threebonded As atoms together form puckered layers which are isostructural to grey As. The mean values of the bond lengths Sn -- As are 277.6 pm (SrSn{sub 2}As{sub 2}) and 279.1 pm (Sr{sub 0.87}Ba{sub 0.13}Sn{sub 2}As{sub 2}) resp. Along (001) the alkaline earth atoms occupy the octahedral interstices of As atoms between each second SnAs layer. The single crystal structure determination of KSnSb confirms the results of the X-ray powder analysis, but leads to slightly different values for the bond lengths.

Single-Molecule Stochastic Resonance

Directory of Open Access Journals (Sweden)

K. Hayashi

2012-08-01

Full Text Available Stochastic resonance (SR is a well-known phenomenon in dynamical systems. It consists of the amplification and optimization of the response of a system assisted by stochastic (random or probabilistic noise. Here we carry out the first experimental study of SR in single DNA hairpins which exhibit cooperatively transitions from folded to unfolded configurations under the action of an oscillating mechanical force applied with optical tweezers. By varying the frequency of the force oscillation, we investigate the folding and unfolding kinetics of DNA hairpins in a periodically driven bistable free-energy potential. We measure several SR quantifiers under varied conditions of the experimental setup such as trap stiffness and length of the molecular handles used for single-molecule manipulation. We find that a good quantifier of the SR is the signal-to-noise ratio (SNR of the spectral density of measured fluctuations in molecular extension of the DNA hairpins. The frequency dependence of the SNR exhibits a peak at a frequency value given by the resonance-matching condition. Finally, we carry out experiments on short hairpins that show how SR might be useful for enhancing the detection of conformational molecular transitions of low SNR.

Ternary systems Sr-{Ni,Cu}-Si: Phase equilibria and crystal structure of ternary phases

International Nuclear Information System (INIS)

Nasir, Navida; Melnychenko-Koblyuk, Nataliya; Grytsiv, Andriy; Rogl, Peter; Giester, Gerald; Wosik, Jaroslaw; Nauer, Gerhard E.

2010-01-01

Phase relations were established in the Sr-poor part of the ternary systems Sr-Ni-Si (900 deg. C) and Sr-Cu-Si (800 deg. C) by light optical microscopy, electron probe microanalysis and X-ray diffraction on as cast and annealed alloys. Two new ternary compounds SrNiSi 3 (BaNiSn 3 -type) and SrNi 9-x Si 4+x (own-type) were found in the Sr-Ni-Si system along with previously reported Sr(Ni x Si 1-x ) 2 (AlB 2 -type). The crystal structure of SrNi 9-x Si 4+x (own-type, x=2.7, a=0.78998(3), c=1.1337(2) nm; space group P4/nbm) was determined from X-ray single crystal counter to be a low symmetry derivative of the cubic, parent NaZn 13 -type. At higher Si-content X-ray Rietveld refinements reveal the formation of a vacant site (□) corresponding to a formula SrNi 5.5 Si 6.5 □ 1.0 . Phase equilibria in the Sr-Cu-Si system are characterized by the compounds SrCu 2-x Si 2+x (ThCr 2 Si 2 -type), Sr(Cu x Si 1-x ) 2 (AlB 2 -type), SrCu 9-x Si 4+x (0≤x≤1.0; CeNi 8.5 Si 4.5 -type) and SrCu 13-x Si x (4≤x≤1.8; NaZn 13 -type). The latter two structure types appear within a continuous solid solution. Neither a type-I nor a type-IX clathrate compound was encountered in the Sr-{Cu,Ni}-Si systems. Structural details are furthermore given for about 14 new ternary compounds from related alloy systems with Ba. - Graphical abstract: The crystal structure of SrNi 9-x Si 4+x (own-type, x=2.7, a=0.78998(3), c=1.1337(2) nm; space group P4/nbm) was determined from X-ray single crystal counter to be a low symmetry derivative of the cubic, parent NaZn 13 -type and is related to CeNi 8.5 Si 4.5 -type.

Crystal structure and energy band and optical properties of phosphate Sr3P4O13

International Nuclear Information System (INIS)

Zhang, Y.-C.; Cheng, W.-D.; Wu, D.-S.; Zhang, H.; Chen, D.-G.; Gong, Y.-J.; Kan, Z.-G.

2004-01-01

A single crystal of the compound Sr 3 P 4 O 13 has been found and the crystal structure has been characterized by means of single crystal X-ray diffraction analysis. The compound crystallizes in triclinic system and belongs to space group P1-bar. It builds up from SrO 7 polyhedra and P 4 O 13 -6 anions and has a layered structure, and the Sr atoms are located in the interlayer space. The absorption and luminescence spectrum of Sr 3 P 4 O 13 microcrystals have been measured. The calculated results of crystal energy band structure by the DFT show that the solid state of Sr 3 P 4 O 13 is an isolator with direct band gap. The calculated total and partial density of states indicate that the top valence bands are contributions from P 3p and O 2p states and low conduction bands mostly originate from Sr atomic states. The calculated optical response functions expect that the Sr 3 P 4 O 13 is a low refractive index, and it is possible that the Sr 3 P 4 O 13 is used to make transparent material between the UV and FR light zone

Beta-delayed proton decay of 73Sr

International Nuclear Information System (INIS)

Batchelder, J.C.; Moltz, D.M.; Ognibene, T.J.; Rowe, M.W.; Tighe, R.J.; Cerny, J.

1993-01-01

The T z =-3/2, A=4n+1 nuclide 73 Sr produced in the 40 Ca( 36 Ar,3n) reaction has been observed via beta-delayed proton emission. A single proton group at a laboratory energy of 3.75±0.04 MeV has been observed, corresponding to decay of the T=3/2 isobaric analog state in 73 Rb to the ground state of 72 Kr. Combining this measurement with a Coulomb displacement energy calculation yields a mass excess for 73 Sr of -31.82±0.24 MeV based on a predicted mass for 72 Kr of -53.94±0.24 MeV

A far ultraviolet spectroscopic study of the reflectance, luminescence and electronic properties of SrMgF4 single crystals

International Nuclear Information System (INIS)

Ogorodnikov, I.N.; Pustovarov, V.A.; Omelkov, S.I.; Isaenko, L.I.; Yelisseyev, A.P.; Goloshumova, A.A.; Lobanov, S.I.

2014-01-01

The electronic properties of single crystals of SrMgF 4 have been determined using low-temperature (10–293 K) time-resolved vacuum ultraviolet synchrotron radiation spectroscopy, far ultraviolet (3.7–36 eV) reflectance spectra and calculations for the spectra of optical functions. The bandgap of investigated compound was found at E g =12.55eV, the energy threshold for creation of the unrelaxed excitons at E n=1 =11.37eV, and the low-energy fundamental absorption edge at 10.3 eV. Two groups of photoluminescence (PL) bands have been identified: the exciton-type emissions at 2.6–3.3 and 3.3–4.2 eV and defect-related emissions at 1.8–2.6 and 4.2–5.5 eV. It was shown that PL excitation (PLE) for the exciton-type emission bands occurs mainly at the low-energy tail of the fundamental absorption of the crystal with a maximum at 10.7 eV. At excitation energies above E g the energy transfer from the host lattice to the PL emission centers is inefficient. The paper discusses the origin of the excitonic-type PLE spectra taking into account the results of modeling the PLE spectra shape in the framework of a simple diffusion theory and surface energy losses. -- Highlights: • Far-ultraviolet reflection spectra of SrMgF 4 were studied. • Photoluminescence (PL) emission and PL excitation spectra were studied. • Optical function spectra were calculated on the basis of experimental data. • Electronic structure properties of undoped SrMgF 4 crystals were determined

87Sr/86Sr sourcing of ponderosa pine used in Anasazi great house construction at Chaco Canyon, New Mexico

Science.gov (United States)

Reynolds, Amanda C.; Betancourt, Julio L.; Quade, Jay; Patchett, P. Jonathan; Dean, Jeffery S.; Stein, John

2005-01-01

Previous analysis of 87Sr/86Sr ratios shows that 10th through 12th century Chaco Canyon was provisioned with plant materials that came from more than 75 km away. This includes (1) corn (Zea mays) grown on the eastern flanks of the Chuska Mountains and floodplain of the San Juan River to the west and north, and (2) spruce (Picea sp.) and fir (Abies sp.) beams from the crest of the Chuska and San Mateo Mountains to the west and south. Here, we extend 87Sr/86Sr analysis to ponderosa pine (Pinus ponderosa) prevalent in the architectural timber at three of the Chacoan great houses (Pueblo Bonito, Chetro Ketl, Pueblo del Arroyo). Like the architectural spruce and fir, much of the ponderosa matches the 87Sr/86Sr ratios of living trees in the Chuska Mountains. Many of the architectural ponderosa, however, have similar ratios to living trees in the La Plata and San Juan Mountains to the north and Lobo Mesa/Hosta Butte to the south. There are no systematic patterns in spruce/fir or ponderosa provenance by great house or time, suggesting the use of stockpiles from a few preferred sources. The multiple and distant sources for food and timber, now based on hundreds of isotopic values from modern and archeological samples, confirm conventional wisdom about the geographic scope of the larger Chacoan system. The complexity of this procurement warns against simple generalizations based on just one species, a single class of botanical artifact, or a few isotopic values.

A Single-Crystal Neutron Diffraction Study on Magnetic Structure of the Quasi-One-Dimensional Antiferromagnet SrCo_2V_2O_8

International Nuclear Information System (INIS)

Liu Juan-Juan; Wang Jin-Chen; Luo Wei; Sheng Jie-Ming; Bao Wei; He Zhang-Zhen; Danilkin, S. A.

2016-01-01

The magnetic structure of the spin-chain antiferromagnet SrCo_2V2O_8 is determined by single-crystal neutron diffraction experiment. The system undergoes a long-range magnetic order below the critical temperature T_N = 4.96 K. The moment of 2.16μ_B per Co at 1.6 K in the screw chain running along the c axis alternates in the c axis. The moments of neighboring screw chains are arranged antiferromagnetically along one in-plane axis and ferromagnetically along the other in-plane axis. This magnetic configuration breaks the four-fold symmetry of the tetragonal crystal structure and leads to two equally populated magnetic twins with the antiferromagnetic vector in the a or b axis. The very similar magnetic state to the isostructural BaCo_2V_2O_8 warrants SrCo_2V_2O_8 as another interesting half-integer spin-chain antiferromagnet for investigation on quantum antiferromagnetism. (paper)

The ternary post-transition metal carbodiimide SrZn(NCN){sub 2}

Energy Technology Data Exchange (ETDEWEB)

Corkett, Alex J.; Konze, Philipp M. [Institute of Inorganic Chemistry, RWTH Aachen University, Aachen (Germany); Dronskowski, Richard [Institute of Inorganic Chemistry, RWTH Aachen University, Aachen (Germany); Juelich-Aachen Research Alliance (JARA-HPC), RWTH-Aachen University, Aachen (Germany)

2017-11-17

SrZn(NCN){sub 2}, the first example of a ternary post-transition metal carbodiimide, was prepared by a solid-state metathesis reaction. The crystal structure was solved from PXRD data and found to adopt the orthorhombic (Cmcm) BaZnSO structure, a high symmetry modification of that expressed by the oxide analogue SrZnO{sub 2}. Locally, SrZn(NCN){sub 2} features ZnN{sub 4} tetrahedra and SrN{sub 6} trigonal prisms similar to those in quarternary LiSr{sub 2}M(NCN){sub 4} (M = Al{sup 3+} and Ga{sup 3+}) phases, however, the overall topologies are distinct with single chains in the former and double chains in the latter. Electronic structure calculations indicate an indirect bandgap of about 2.95 eV in SrZn(NCN){sub 2}, slightly lower than the experimentally observed bandgap of 3.4 eV in SrZnO{sub 2} and consistent with a greater degree of covalency. The structural similarities between SrZn(NCN){sub 2} and oxychalcogenide analogues highlight the pseudochalcogenide character of NCN{sup 2-} and suggest that the title compound may serve as a template for accessing novel ternary carbodiimides featuring tetrahedrally coordinated transition metals. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Single inhalation exposure to 90SrCl2 in the Beagle dog: early hematological effects

International Nuclear Information System (INIS)

Gillett, N.; Muggenburg, B.A.; Hahn, F.F.; Boecker, B.B.; Rebar, A.H.; McClellan, R.O.

1985-01-01

Young adult Beagle dogs were exposed once to aerosols containing 90 SrCl 2 to obtain initial body burdens ranging from 2.5 to 250 uCi 90 Sr/kg body weight and subsequently observed throughout their life span. All of the dogs are now dead. The primary cause of death over the entire length of the study was radiation-induced osteosarcomas. However, six dogs died at less than 30 days after exposure as a result of a radiation-induced bone marrow aplasia. Review of hematological parameters of all dogs showed a similar, consistent, and often dramatic pancytopenia in those animals having a long-term retained burden of greater than 10 uCi 90 Sr/kg. The hematologic changes were similar to those seen in people exposed to high doses of whole body external radiation. 4 references, 1 figure, 1 table

A solution for the preparation of hexagonal M-type SrFe{sub 12}O{sub 19} ferrite using egg-white: Structural and magnetic properties

Energy Technology Data Exchange (ETDEWEB)

Li, Tingting; Li, Yang; Wu, Ruonan; Zhou, Han; Fang, Xiaochen [Anhui Key Laboratory of Metal Materials and Processing, School of Materials Science and Engineering, Anhui University of Technology, Maanshan 243002 (China); Su, Shubing [School of Electronic and Information Engineering, Ningbo University of Technology, Ningbo 315016 (China); Xia, Ailin, E-mail: alxia@126.com [Anhui Key Laboratory of Metal Materials and Processing, School of Materials Science and Engineering, Anhui University of Technology, Maanshan 243002 (China); Jin, Chuangui; Liu, Xianguo [Anhui Key Laboratory of Metal Materials and Processing, School of Materials Science and Engineering, Anhui University of Technology, Maanshan 243002 (China)

2015-11-01

A new sol–gel route using egg-white as the binder of metal ions, is developed to prepare hexagonal M-type SrFe{sub 12}O{sub 19} ferrite in this study, and the effects of different atomic ratio of Sr and Fe (Sr/Fe), sintering temperature (T{sub s}) and usage of egg-white (M{sub ew}) on the phase formation, morphology and magnetic properties of specimens are studied. It is found that the single-phase SrFe{sub 12}O{sub 19} ferrite only can be obtained under a Sr/Fe of 1:8 and a T{sub s} between 1000 °C and 1300 °C. The magnetic properties of specimens are also obviously affected by the different Sr/Fe and T{sub s}, primarily due to the emergency of impurities. The M{sub ew} has an obvious impact on the crystallinity of specimens, which consequently affects their magnetic properties. In our study, the optimum conditions to prepare the single-phase SrFe{sub 12}O{sub 19} ferrite are Sr/Fe=1:8, M{sub ew}= 3 g and T{sub s} =1200 °C. - Highlights: • Single-phase SrM ferrite was obtained via a novel sol–gel method using egg-white. • Single-phase SrM ferrite was obtained under Sr/Fe=1:8 and T{sub s} between 1000 and 1300 °C. • The usage of egg-white affects the crystallinity and magnetic properties markedly.

Equivalent flow rate concept used in near field transport model COMP23 - Proposed values for SR 97

International Nuclear Information System (INIS)

Moreno, L.

1998-11-01

SKB is using NUCTRAN to calculate transport of radionuclides from a possible defective canister into the far field. NUCTRAN is included in the Performance Assessment model chain that calculates the release from the canister into the biosphere. In the chain, NUCTRAN is denoted COMP23. In order to calculate the transport of radionuclides by diffusion into the flowing water in the rock, NUCTRAN uses the concept of equivalent flow rate, Q eq . To calculate the value of Q eq in the different paths, COMP23 needs information about the Darcy velocity, the geometry of the system, material properties and the flow porosity in the rock. At present, this information is supplied to COMP23 by means of three parameters. The aim of this note is to propose a method to calculate the flow equivalent within the SR 97 project. Estimated intervals of the factors to adopt HYDRASTAR results to COMP23 are presented. Since it is difficult to give general validity to the factors, solely proposed factor intervals are presented to obtain equivalent flow rate values for COMP23. To obtain accurate equivalent flow rate values, information about the hydraulic conditions at canister locations in the groundwater model should be available for the near field model or the Q eq values could be calculated directly in the groundwater flow model. One of the main tasks in the SR 97 project is to show the barrier performance of the rock using different alternative models for flow and transport. In addition, the Alternative Model Project (AMP) aims to show how robust the assessment model description is, in terms of relevant far field performance measures. In the AMP, three main approaches were used, namely, the Stochastic Continuum approach, the Channel Network model and the Discrete Feature Network model

Investigating the hydrological significance of stalagmite geochemistry (Mg, Sr) using Sr isotope and particulate element records across the Late Glacial-to-Holocene transition

Science.gov (United States)

Belli, R.; Borsato, A.; Frisia, S.; Drysdale, R.; Maas, R.; Greig, A.

2017-02-01

The trace element and Sr isotope records in two coeval stalagmites characterized by different growth rates and flow regimes at Savi cave (Grotta Savi, NE Italy) reveal different sources and incorporation mechanisms for Mg and Sr. Mg is sourced primarily from dissolved cave host rock while particulate Mg derived from soil plays a subordinate role. The presence of particulate-borne Mg is inferred from the co-variation of Mg and particle-associated elements (Th, Al and Mn) which are preferentially concentrated in open columnar calcite layers. Variation in Mg concentrations corrected for particle-influenced components, the Mgc parameter, is controlled by water-rock interaction, with higher and lower Mgc during dry and wet phases, respectively. This is thought to reflect incongruent dissolution of Mg-rich phases. Correction of Sr concentrations for contributions from airborne exogenic Sr, based on 87Sr/86Sr ratios, yields the bedrock-only contribution (Src). Src variation in stalagmite calcite is influenced by speleothem growth rate and by variation of the calcite-water Sr partitioning in wet and dry phases, and only to a minor extent by incongruent dissolution of Mg-rich phases. Concentration profiles for Mgc and Srcg (corrected for growth rate effects) show inverse correlations and are inferred to show hydrological significance which is captured in a hydrological index, HI. We suggest HI provides robust information on water-rock interaction related to hydrological changes and can be utilized in both wet and semi-arid environments, provided the corrections for soil Mg and exogenic Sr can be applied with confidence. Application of the HI index allows correction of Grotta Savi oxygen isotope data, to yield a δ18Oc time series that shows when changes in moisture sources and atmospheric reorganization, or changes in moisture amount, were significant. This is especially evident during the Younger Dryas (YD). The Savi record supports the concept of a two-phase YD, marked by

Hole hopping rates in single strand oligonucleotides

Energy Technology Data Exchange (ETDEWEB)

Borrelli, Raffaele [Dipartimento di Scienze Agrarie, Forestali e Alimentari, Università di Torino, Largo Paolo Braccini 2, I-10095 Grugliasco, TO (Italy); Capobianco, Amedeo [Dipartimento di Chimica e Biologia, Università di Salerno, Via Giovanni Paolo II, I-84084 Fisciano, SA (Italy); Peluso, Andrea, E-mail: apeluso@unisa.it [Dipartimento di Chimica e Biologia, Università di Salerno, Via Giovanni Paolo II, I-84084 Fisciano, SA (Italy)

2014-08-31

Highlights: • DNA hole transfer rates have been computed. • Delocalized adenine domains significantly affect hole transfer rates in DNA. • Franck–Condon weighted density of state from DFT normal modes. • DNA application in molecular electronics. - Abstract: The rates of hole transfer between guanine and adenine in single strand DNA have been evaluated by using Fermi’s golden rule and Kubo’s generating function approach for the Franck–Condon weighted density of states. The whole sets of the normal modes and vibrational frequencies of the two nucleobases, obtained at DFT/B3LYP level of calculation, have been considered in computations. The results show that in single strand the pyramidalization/planarization mode of the amino groups of both nucleobases plays the major role. At room temperature, the Franck–Condon density of states extends over a wide range of hole site energy difference, 0–1 eV, giving some hints about the design of oligonucleotides of potential technological interest.

Metastable honeycomb SrTiO_3/SrIrO_3 heterostructures

International Nuclear Information System (INIS)

Anderson, T. J.; Ryu, S.; Podkaminer, J. P.; Ma, Y.; Eom, C. B.; Zhou, H.; Xie, L.; Irwin, J.; Rzchowski, M. S.; Pan, X. Q.

2016-01-01

Recent theory predictions of exotic band topologies in (111) honeycomb perovskite SrIrO_3 layers sandwiched between SrTiO_3 have garnered much attention in the condensed matter physics and materials communities. However, perovskite SrIrO_3 film growth in the (111) direction remains unreported, as efforts to synthesize pure SrIrO_3 on (111) perovskite substrates have yielded films with monoclinic symmetry rather than the perovskite structure required by theory predictions. In this study, we report the synthesis of ultra-thin metastable perovskite SrIrO_3 films capped with SrTiO_3 grown on (111) SrTiO_3 substrates by pulsed laser deposition. The atomic structure of the ultra-thin films was examined with scanning transmission electron microscopy (STEM), which suggests a perovskite layering distinct from the bulk SrIrO_3 monoclinic phase. In-plane 3-fold symmetry for the entire heterostructure was confirmed using synchrotron surface X-ray diffraction to measure symmetry equivalent crystal truncation rods. Our findings demonstrate the ability to stabilize (111) honeycomb perovskite SrIrO_3, which provides an experimental avenue to probe the phenomena predicted for this material system.

Stable and Radiogenic Sr Isotopes in Barite - Clues on the Links Between Weathering, Climate and the C Cycle

Science.gov (United States)

Paytan, A.; Eisenhauer, A.; Wallmann, K. J. G.; Griffith, E. M.; Ridgwell, A.

2017-12-01

The radiogenic Sr-isotopic signature (87Sr/86Sr) of seawater fluctuates primarily in response to changes in the inputs of Sr from weathering and hydrothermal activity, which have distinct 87Sr/86Sr values. Changes in the isotopic ratio of the weathered terrain also contribute to observed changes in 87Sr/86Sr. The stable Sr-isotope ratios in seawater (mass dependent isotopic fractionation; δ88/86Sr) fluctuate primarily in response to the rate of calcium carbonate (CaCO3) accumulation at the seafloor. Together the radiogenic and stable Sr can constrain the coupling between weathering and sedimentation and shed light on the relation between weathering, CaCO3 deposition, the global carbon (C) cycle and climate. Reconstruction of the coupled stable and radiogenic Sr seawater curves over the past 35 Ma of Earth history indicates that the location and rate of CaCO3 burial in the ocean fluctuated considerably over the past 35 Ma. Between 35 to 18 Ma a reduction in neritic CaCO3 burial and increased burial in pelagic settings is observed. The trend was reversed between 20 and 3 Ma and finally over the last 3 million years a rapid change from neritic to pelagic burial is seen. The lack of continues increase of pelagic CaCO3 burial rates suggests that silicate weathering rates have not increased monotonically over the past 35 Ma implying strong feedbacks operating in the climate system - lower atmospheric pCO2 and cooling trends (which control chemical weathering as seen from carbonate deposition in the ocean) countered the effects of uplift (which controls physical weathering) - modulating weathering rates and preventing a runaway ice-house. In addition the data suggests considerable fluctuations in seawater Sr concentrations over time. These data demonstrate how using multiple isotope proxies can help constrain interpretations of the geological record.

Optimisation of thallium ''1223'' high-temperature superconducting wire by a single-stage cold deformation process. [TlPbSrCaCuO

Energy Technology Data Exchange (ETDEWEB)

Glowacki, B A [IRC in Superconductivity, Cambridge (United Kingdom) Materials Science and Metallurgy, Cambridge (United Kingdom); Ashworth, S P [BICC Cables Ltd., Erith (United Kingdom)

1992-09-15

Superconducting tapes containing (Tl[sub 0.5]Pb[sub 0.5])Sr[sub 2]Ca[sub 2]Cu[sub 3]O[sub 9] were manufactured by a powder-in-tube technique and a single annealing stage. The (Tl[sub 0.5]Pb[sub 0.5])Sr[sub 2]Ca[sub 2]Cu[sub 3]O[sub 9] forms a ''1223'' structure with a Tc of over 120 K. A cold pressing stage was found to be necessary to achieve the higher J[sub c] values at 77 K. The transport J[sub c] was found to depend on: the annealing temperature, annealing time and pressing pressure. SEM examination of the Tl-1223 grain structure showed a marked difference between rolled and pressed tapes. This is ascribed to the production of a lead-rich phase during pressing, this is supported by XRD evidence. No significant degree of grain alignment was found in the Tl-1223 tapes, either by XRD analysis or by the measurement of transport critical current in applied magnetic fields. (orig.).

Fabrication of SrGe2 thin films on Ge (100), (110), and (111) substrates

Science.gov (United States)

Imajo, T.; Toko, K.; Takabe, R.; Saitoh, N.; Yoshizawa, N.; Suemasu, T.

2018-01-01

Semiconductor strontium digermanide (SrGe2) has a large absorption coefficient in the near-infrared light region and is expected to be useful for multijunction solar cells. This study firstly demonstrates the formation of SrGe2 thin films via a reactive deposition epitaxy on Ge substrates. The growth morphology of SrGe2 dramatically changed depending on the growth temperature (300-700 °C) and the crystal orientation of the Ge substrate. We succeeded in obtaining single-oriented SrGe2 using a Ge (110) substrate at 500 °C. Development on Si or glass substrates will lead to the application of SrGe2 to high-efficiency thin-film solar cells.

Anisotropic Resistivities of Precisely Oxygen Controlled Single-Crystal Bi2Sr2CaCu2O8+δ: Systematic Study on ''Spin Gap'' Effect

International Nuclear Information System (INIS)

Watanabe, T.; Matsuda, A.; Fujii, T.; Matsuda, A.

1997-01-01

The in-plane resistivity ρ a (T) and the out-of-plane resistivity ρ c (T) have been systematically measured for Bi 2 Sr 2 CaCu 2 O 8+δ single crystals with their oxygen contents precisely controlled. In the underdoped region, deviation from T -linear in-plane resistivity, which evidences the opening of the spin gap, is clearly observed, while the out-of-plane resistivity is well reproduced by the activation-type phenomenological formula ρ c (T)=(a/T)exp (Δ/T)+c . In contrast to the YBa 2 Cu 3 O 7-δ system, we find that the onset of the semiconducting ρ c (T) does not coincide with the opening of the spin gap seen in the ρ a (T) in this Bi 2 Sr 2 CaCu 2 O 8+δ system. copyright 1997 The American Physical Society

Inelastic collisions and density-dependent excitation suppression in a 87Sr optical lattice clock

International Nuclear Information System (INIS)

Bishof, M.; Martin, M. J.; Swallows, M. D.; Benko, C.; Lin, Y.; Quemener, G.; Rey, A. M.; Ye, J.

2011-01-01

We observe two-body loss of 3 P 0 87 Sr atoms trapped in a one-dimensional optical lattice. We measure loss rate coefficients for atomic samples between 1 and 6 μK that are prepared either in a single nuclear-spin sublevel or with equal populations in two sublevels. The measured temperature and nuclear-spin preparation dependence of rate coefficients agree well with calculations and reveal that rate coefficients for distinguishable atoms are only slightly enhanced over those of indistinguishable atoms. We further observe a suppression of excitation and losses during interrogation of the 1 S 0 - 3 P 0 transition as density increases and Rabi frequency decreases, which suggests the presence of strong interactions in our dynamically driven many-body system.

Observation of a commensurate array of flux chains in tilted flux lattices in Bi-Sr-Ca-Cu-O single crystals

International Nuclear Information System (INIS)

Bolle, C.A.; Gammel, P.L.; Grier, D.G.; Murray, C.A.; Bishop, D.J.; Mitzi, D.B.; Kapitulnik, A.

1991-01-01

We report the observation of a novel flux-lattice structure, a commensurate array of flux-line chains. Our experiments consist of the magnetic decoration of the flux lattices in single crystals of Ba-Sr-Ca-Cu-O where the magnetic field is applied at an angle with respect to the conducting planes. For a narrow range of angles, the equilibrium structure is one with uniformly spaced chains with a higher line density of vortices than the background lattice. Our observations are in qualitative agreement with theories which suggest that, in strongly anisotropic materials the vortices develop an attractive interaction in tilted magnetic fields

Bi2(Sr, Ln)2CuOz (Ln = Nd, Sm) phases: stability, crystal growth and superconducting properties

International Nuclear Information System (INIS)

Faqir, H.; Kikuchi, M.; Syono, Y.; Mansori, M.; Satre, P.; Sebaoun, A.; Vacquier, G.

2000-01-01

Bi 2 (Sr,Ln) 2 CuO z (Ln = Nd, Sm) single crystals were successfully grown by a self-flux method from stoichiometric and (Bi, Cu)-rich melts. Thermal analysis and thermogravimetry were used to determine stability and the melting sequence of Bi 2 (Sr,Ln) 2 CuO z phases in air. As-grown crystals of the ideal Bi 2 (Sr,Ln) 2 CuO z phase, of dimensions 1x0.5x0.03 mm 3 , exhibit superconducting behaviour with critical temperature T c = 21 K for the Bi 1.9 Sr 1.6 Nd 0.6 CuO z crystal and Tc = 14 K for the Bi 1.8 Sr 1.6 Sm 0.6 CuO z crystal. The compositions of these crystals were homogeneous and close to the stoichiometric composition. We report on the growth of Bi 2 Sr 2-x Sm x CuO z single crystals of large dimensions 9x3x0.03 mm 3 using Bi 2 Sr 1.5 Sm 0.5 CuO z as precursor and Bi 2 CuO 4 as flux. (author)

Rapid method for determining Sr-89 and Sr-90 using Cherenkov and proportional counting; Schnellmethode zur Bestimmung von SR-89 und SR-90 durch Cerenkov- und Proportionalzaehlermessungen

Energy Technology Data Exchange (ETDEWEB)

Lange, S.; Wende, C.; Schwokowski, R.; Alisch-Mark, M.; Abraham, A.; Heinrich, T. [Staatliche Betriebsgesellschaft fuer Umwelt und Landwirtschaft, Radebeul (Germany)

2016-07-01

A rapid method for determining Sr-89 and Sr-90 in water, milk and biological samples has been developed and tested. After sample preparation strontium is separated by extraction chromatography using Sr resin. Eluate is divided and transfered to LSC vial and filter paper by SrCO{sub 3} precipitation. A Hidex 300 SL TDCR liquid scintillation counter and Thermo Fisher low level proportional counter have been used. Chemical yield of Sr-85 tracer is determined by Gamma spectroscopy. Uncertainty budget, decision threshold and detection limit are calculated in accordance with GUM and ISO 11929.

Modulation-free bismuth-lead cuprate superconductors: BiPbSr1+xL1-xCuO6 and BiPbSr2Y1-xCaxCu2O8

International Nuclear Information System (INIS)

Manivannan, V.; Gopalakrishnan, J.; Rao, C.N.R.

1991-01-01

Modulation-free BiPbSrLCuO 6 (L=La, Pr, Nd) and BiPbSr 2 YCu 2 O 8 , which are isotypic with the n=1 and 2 members of the Bi 2 Sr 2 Ca n-1 Cu n O 2n+4 family, have been prepared and characterized. These parent compounds are nonsuperconducting, but when doped with holes by substitution chemistry give modulation-free superconducting cuprates of the general formulas BiPbSr 1+xL1-x CuO 6 and BiPbSr 2 Y 1-x Ca x Cu 2 O 8 , exhibiting maximum T c 's of 24 and 85 K, respectively. Significantly, the hole concentration at the maximum T c is 0.12 in the cuprate family with a single Cu-O layer and 0.22 in that with two Cu-O layers

Crystal growth and electronic structure of low-temperature phase SrMgF{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Atuchin, Victor V. [Laboratory of Optical Materials and Structures, Institute of Semiconductor Physics, SB RAS, Novosibirsk 630090 (Russian Federation); Functional Electronics Laboratory, Tomsk State University, Tomsk 634050 (Russian Federation); Laboratory of Semiconductor and Dielectric Materials, Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Goloshumova, Alina A. [Laboratory of Crystal Growth, Institute of Geology and Mineralogy, SB RAS, Novosibirsk 630090 (Russian Federation); Isaenko, Ludmila I. [Laboratory of Semiconductor and Dielectric Materials, Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Laboratory of Crystal Growth, Institute of Geology and Mineralogy, SB RAS, Novosibirsk 630090 (Russian Federation); Jiang, Xingxing [BCCRD, Key Laboratory of Functional Crystals and Laser Technology, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Lobanov, Sergey I. [Laboratory of Crystal Growth, Institute of Geology and Mineralogy, SB RAS, Novosibirsk 630090 (Russian Federation); Zhang, Zhaoming [Australian Nuclear Science & Technology Organisation, Lucas Heights, NSW 2234 (Australia); Lin, Zheshuai, E-mail: zslin@mail.ipc.ac.cn [BCCRD, Key Laboratory of Functional Crystals and Laser Technology, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China)

2016-04-15

Using the vertical Bridgman method, the single crystal of low temperature phase SrMgF{sub 4} is obtained. The crystal is in a very good optical quality with the size of 10×7×5 mm{sup 3}. Detailed photoemission spectra of the element core levels are determined by a monochromatic AlKa (1486.6 eV) X-ray source. Moreover, the first-principles calculations are performed to investigate the electronic structure of SrMgF{sub 4}. A good agreement between experimental and calculated results is achieved. It is demonstrated that almost all the electronic orbitals are strongly localized and the hybridization with the others is very small, but the Mg–F bonds covalency is relatively stronger than that of Sr–F bonds. - Graphical abstract: Large size of low-temperature phase SrMgF{sub 4} crystal was obtained (right) and its electronic structure was investigated by X-ray photoelectron spectroscopy and first-principles calculation (left). - Highlights: • Large size single crystal of low-temperature phase SrMgF{sub 4} is obtained. • Electronic structure of SrMgF{sub 4} is measured by X-ray photoelectron spectroscopy. • Partial densities of states are determined by first-principles calculation. • Good agreement between experimental and calculated results is achieved. • Strong ionic characteristics of chemical bonds are exhibited in SrMgF{sub 4}.

Environmental 90Sr measurements

Science.gov (United States)

Paul, M.; Berkovits, D.; Cecil, L.D.; Feldstein, H.; Hershkowitz, A.; Kashiv, Y.; Vogt, S.

1997-01-01

90Sr (T1/2 = 28.5 years) is a long-lived radionuclide produced in nuclear fission. Fast radiochemical detection of 90Sr in environmental samples is not feasible using current analytical methods. Accelerator Mass Spectrometry (AMS) measurements of 90Sr were made with the Rehovot 14UD Pelletron accelerator at a terminal voltage of 11 or 12 MV using our standard detection system. Injection of hydride ions (SrH3-) was chosen owing to high beam intensity and low Coulomb explosion effects. 90Sr ions were identified and discriminated from isobaric 90Zr by measuring time of flight, total energy and three independent energy-loss signals in an ionization chamber. A reference sample and a ground-water sample were successfully measured. The detection limit determined for a laboratory blank by the residual counts in the 90Sr region is 90Sr/Sr = 3 ?? 10-13, corresponding in practice to (2-4) ?? 10790Sr atoms or about 0.5-1 pCi/L in environmental water samples.

Maxdose-SR and popdose-SR routine release atmospheric dose models used at SRS

Energy Technology Data Exchange (ETDEWEB)

Jannik, G. T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Trimor, P. P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-07-28

MAXDOSE-SR and POPDOSE-SR are used to calculate dose to the offsite Reference Person and to the surrounding Savannah River Site (SRS) population respectively following routine releases of atmospheric radioactivity. These models are currently accessed through the Dose Model Version 2014 graphical user interface (GUI). MAXDOSE-SR and POPDOSE-SR are personal computer (PC) versions of MAXIGASP and POPGASP, which both resided on the SRS IBM Mainframe. These two codes follow U.S. Nuclear Regulatory Commission (USNRC) Regulatory Guides 1.109 and 1.111 (1977a, 1977b). The basis for MAXDOSE-SR and POPDOSE-SR are USNRC developed codes XOQDOQ (Sagendorf et. al 1982) and GASPAR (Eckerman et. al 1980). Both of these codes have previously been verified for use at SRS (Simpkins 1999 and 2000). The revisions incorporated into MAXDOSE-SR and POPDOSE-SR Version 2014 (hereafter referred to as MAXDOSE-SR and POPDOSE-SR unless otherwise noted) were made per Computer Program Modification Tracker (CPMT) number Q-CMT-A-00016 (Appendix D). Version 2014 was verified for use at SRS in Dixon (2014).

Domain structure and magnetic properties of epitaxial SrRuO sub 3 films grown on SrTiO sub 3 (100) substrates by ion beam sputtering

CERN Document Server

Oh, S H

2000-01-01

The domain structure of epitaxial SrRuO sub 3 thin films grown on SrTiO sub 3 (100) substrates by using ion beam sputtering has been investigated with transmission electron microscopy (TEM) and X-ray diffraction (XRD). The SrRuO sub 3 films grown in the present study revealed a unique cube-on-cube epitaxial relationship, i.e., (100) sub S sub R sub O ll (100) sub S sub T sub O , [010] sub S sub R sub O ll [101] sub S sub T sub O , prevailing with a cubic single-domain structure. The cubic SrRuO sub 3 thin films that were inherently with free from RuO sub 6 octahedron tilting exhibited higher resistivity with suppressed magnetic properties. The Curie temperature of the thin films was suppressed by 60 K from 160 K for the bulk specimen, and the saturation magnetic moment was reduced by a significant amount. The tetragonal distortion of the SrRuO sub 3 thin films due to coherent growth with the substrate seemed to result in a strong magnetic anisotropy.

Doping evolution of the electronic structure in the single-layer cuprates Bi2Sr2−xLaxCuO6 delta: Comparison with other single-layer cuprates

Energy Technology Data Exchange (ETDEWEB)

Hashimoto, M.

2010-04-30

We have performed angle-resolved photoemission and core-level x-ray photoemission studies of the single-layer cuprate Bi{sub 2}Sr{sub 2-x}La{sub x}CuO{sub 6+{delta}} (Bi2201) and revealed the doping evolution of the electronic structure from the lightly-doped to optimally-doped regions. We have observed the formation of the dispersive quasi-particle band, evolution of the Fermi 'arc' into the Fermi surface and the shift of the chemical potential with hole doping as in other cuprates. The doping evolution in Bi2201 is similar to that in Ca{sub 2-x}Na{sub x}CuO{sub 2}Cl{sub 2} (Na-CCOC), where a rapid chemical potential shift toward the lower Hubbard band of the parent insulator has been observed, but is quite different from that in La{sub 2-x}Sr{sub x}CuO{sub 4} (LSCO), where the chemical potential does not shift, yet the dispersive band and the Fermi arc/surface are formed around the Fermi level already in the lightly-doped region. The (underlying) Fermi surface shape and band dispersions are quantitatively analyzed using tightbinding fit, and the deduced next-nearest-neighbor hopping integral t also confirm the similarity to Na-CCOC and the difference from LSCO.

Is the Modern Marine 87Sr/86Sr Cycle Balanced?

Science.gov (United States)

Peucker-Ehrenbrink, B.

2017-12-01

The marine 87Sr/86Sr record is one of the best-reconstructed isotope records with thousands of high quality measurements spanning the past 800 million years. It records a global signal of tectonic, biotic and climatic processes on Earth. Yet despite decades of research we still do not know whether the current marine Sr budget is in steady state. Studies of the marine 88Sr/86Sr record indicate that sources and sinks do not balance. The magnitude and isotope composition of the terrestrial inputs are being debated, and the magnitude and temporal variability of unradiogenic contributions are not well constrained. Here I provide a revised assessment of all continental sources of Sr to the ocean, including river runoff, submarine groundwater discharge (Beck et al., 2013), dissolution of riverine suspended matter in seawater and dissolution of volcanic ash deposited on the ocean (Jones et al., 2012). I contrast continental sources of Sr with estimates of marine sources of Sr to seawater, specifically high- and low-temperature submarine hydrothermal fluids, as well as diffusive diagenetic fluxes. Best current data imply that unradiogenic submarine hydrothermal inputs to seawater are insufficient to balance the flux of radiogenic continental Sr. The revised assessment of riverine contributions is based on Sr data for almost 230 rivers, an increasing amount of time-series data for such rivers, as well as river discharge and sediment flux data for more than 2000 rivers. Regional sampling biases have been corrected with the aid of digital bedrock maps, specifically along the western margin of North America, East Africa and the large drainage region of Arabia, India and SE Asia. Significant uncertainty in the chemical and isotopic compositions of runoff from Greenland and East Africa remains. The main uncertainty in the budget, however, is related to the possibility that modern rivers do not represent the pre-anthropogenic (natural) state of continental runoff (e.g. Ganges

Atomic scale studies of La/Sr ordering in La2-2xSr1+2xMn2O7 single crystals

KAUST Repository

Roldan, Manuel

2016-12-21

Many fascinating properties of materials depend strongly on the local chemical environment. This is the case for many complex oxides, such as materials with colossal magnetoresistance, where small variations of composition at the atomic scale can affect drastically the macroscopic properties. The main objective of the present work is to analyze the local chemical composition with atomic resolution and to find out if any underlying chemical order is in any way connected to the magnetic properties of double perovskite La2-2xSr1+2xMn2O7 (LSMO) manganite oxides. For these compounds, charge and orbital ordering are observed for some doping values near x = 0.50 [1, 2]. For this purpose, we have use aberration corrected scanning transmission electron microscopy (STEM) combined with electron energy-loss spectroscopy (EELS) measurements and also theoretical simulations. We have compared different compositions within three distinct magnetic regions of the phase diagram: a ferromagnetic metallic sample with x=0.36, an insulating, antiferromagnetic (AF) x=0.56 and an additional AF x=0.50 sample which also exhibits charge ordering. High angle annular dark-field (HAADF) images, also known as Z-contrast, confirm that our single crystals exhibit high crystal quality. No secondary phases or defects are observed. Figure 1 displays an atomic resolution image obtained with the c-axis perpendicular to the electron beam of a x=0.50 sample. The perovskite (P)-like planes and the rock salt (R)-like planes are clearly observed, highlighted in green and red, respectively, on the image. The P-like planes exhibit a slightly high contrast, suggesting a possible La enrichment. EELS atomic resolution maps (inset) support a high degree of La segregation on those planes, while R-like planes are Sr rich. However, due to dechanneling of the beam, detailed image simulations are essential to accurately quantify the local chemical composition in an atomic column-by-atomic column fashion. For all our

Growth rate of YBCO-Ag superconducting single grains

Science.gov (United States)

Congreve, J. V. J.; Shi, Y. H.; Dennis, A. R.; Durrell, J. H.; Cardwell, D. A.

2017-12-01

The large scale use of (RE)Ba2Cu3O7 bulk superconductors, where RE=Y, Gd, Sm, is, in part, limited by the relatively poor mechanical properties of these inherently brittle ceramic materials. It is reported that alloying of (RE)Ba2Cu3O7 with silver enables a significant improvement in the mechanical strength of bulk, single grain samples without any detrimental effect on their superconducting properties. However, due to the complexity and number of inter-related variables involved in the top seeded melt growth (TSMG) process, the growth of large single grains is difficult and the addition of silver makes it even more difficult to achieve successful growth reliably. The key processing variables in the TSMG process include the times and temperatures of the stages within the heating profile, which can be derived from the growth rate during the growth process. To date, the growth rate of the YBa2Cu3O7-Ag system has not been reported in detail and it is this lacuna that we have sought to address. In this work we measure the growth rate of the YBCO-Ag system using a method based on continuous cooling and isothermal holding (CCIH). We have determined the growth rate by measuring the side length of the crystallised region for a number of samples for specified isothermal hold temperatures and periods. This has enabled the growth rate to be modelled and from this an optimized heating profile for the successful growth of YBCO-Ag single grains to be derived.

Growth and structural characterization of single crystals of the magnetic superconductor Ru1-xSr2-yGd1+yCu2+xO8-δ (RuGd-1212) obtained by the partial melting technique

Science.gov (United States)

Yamaki, K.; Bamba, Y.; Mochiku, T.; Funahashi, S.; Matsushita, Y.; Irie, A.

2018-05-01

In this study, cubic single crystals of the magnetic superconductor Ru1-xSr2-yGd1+yCu2+xO8-δ (RuGd-1212) with typical dimensions of 100-150 μm in length were grown by the partial melting technique. Multiple 00l reflections were first observed by XRD measurements of the bulk RuGd-1212 single crystals. The resistivity of the obtained crystals was roughly estimated to be ∼24-80 mΩ cm and no superconducting transition was observed down to 4.2 K. From the XRD measurements and refinement of the crystal structure, it was apparent that the Ru and Sr sites of the single-crystal RuGd-1212 were partially substituted by Cu and Gd, respectively. Oxygen defects were found to be minor (δ ≈ 0.1). The lattice parameters a and c of the single crystals were found to be larger and smaller, respectively, than those of a polycrystalline sample.

Dielectric relaxation in Yb-doped SrZrO3

International Nuclear Information System (INIS)

Kamishima, O; Abe, Y; Ishii, T; Kawamura, J; Hattori, T

2004-01-01

The dielectric constant of the proton conductor SrZr 1-x Yb x O 3 (x 0-0.1) was measured as a function of temperature and frequency. Two well-defined relaxation peaks were observed in SrZrO 3 doped with more than 1 mol% of Yb. The assignment of the two dielectric relaxations is discussed in terms of IR spectra and by free energy calculation for a miscibility of dopant Yb ions. The Yb concentration dependence of the relaxation strength of the two dielectric relaxations is in agreement with the results calculated from the free energy. The two relaxations can be assigned to a reorientation of a single Yb-OH dipole and of Yb-OH dipoles associated with Yb-clusters. The attractive energy for Yb-clustering in SrZrO 3 is evaluated at about -85 meV

Large room-temperature tunneling anisotropic magnetoresistance and electroresistance in single ferromagnet/Nb:SrTiO3 Schottky devices.

Science.gov (United States)

Kamerbeek, Alexander M; Ruiter, Roald; Banerjee, Tamalika

2018-01-22

There is a large effort in research and development to realize electronic devices capable of storing information in new ways - for instance devices which simultaneously exhibit electro and magnetoresistance. However it remains a challenge to create devices in which both effects coexist. In this work we show that the well-known electroresistance in noble metal-Nb:SrTiO 3 Schottky junctions can be augmented by a magnetoresistance effect in the same junction. This is realized by replacing the noble metal electrode with ferromagnetic Co. This magnetoresistance manifests as a room temperature tunneling anisotropic magnetoresistance (TAMR). The maximum room temperature TAMR (1.6%) is significantly larger and robuster with bias than observed earlier, not using Nb:SrTiO 3 . In a different set of devices, a thin amorphous AlO x interlayer inserted between Co and Nb:SrTiO 3 , reduces the TAMR by more than 2 orders of magnitude. This points to the importance of intimate contact between the Co and Nb:SrTiO 3 for the TAMR effect. This is explained by electric field enhanced spin-orbit coupling of the interfacial Co layer in contact with Nb:SrTiO 3 . We propose that the large TAMR likely has its origin in the 3d orbital derived conduction band and large relative permittivity of Nb:SrTiO 3 and discuss ways to further enhance the TAMR.

Experimental autoabsorption curve 90Sr in SrCO3. Efficiency calculation to detection of 90Sr, 90Y and 90Sr + 90Y in a beta gas proportional counter

International Nuclear Information System (INIS)

Gasco, C.; Alvarez, A.

1987-01-01

Strontium-90 has been determined by radiochemical separation techniques in environmental samples. These techniques, of course, cannot separate the two strontium radionuclides from each other of from stable strontium. Consequently the end product of the chemical separation contains all strontium isotopes in SrCO 3 . The beta particules emitted by 90 Sr are absorbed by the SrCO 3 precipitate. This is the main source of error in the activity measurement. It has been prepared sources of 90 Sr in SrCO 3 in order to determinate the counting efficiency and autoabsorption curve. Also detection efficiencies have been calibrated using known activities of 90 Y and equilibrium mixture of 90 Sr+ 90 Y in the same geometry than our samples. The activity of 90 Sr by ingrowth of 90 Y has been calculated by our computer program. (author). 2 figs., 3 refs

Cellular uptake and radiosensitization of SR-2508 loaded PLGA nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Jin Cheng [Fourth Military Medical University, Department of Radiation Medicine (China); Bai Ling [Xi' an Gaoxin Hospital, Department of Clinical Laboratories (China); Wu Hong [Fourth Military Medical University, Department of Pharmacy (China); Teng Zenghui [Fourth Military Medical University, Department of Pharmacology (China); Guo Guozhen, E-mail: guozhengg@tom.co [Fourth Military Medical University, Department of Radiation Medicine (China); Chen Jingyuan, E-mail: jy_chen@fmmu.edu.c [Fourth Military Medical University, Department of Occupational and Environmental Health (China)

2008-08-15

SR-2508 (etanidazole), a hypoxic radiosensitizer, has potential applications in radiotherapy. The poly(d,l-lactide-co-glycolide)(PLGA) nanoparticles containing SR-2508 were prepared by w/o/w emulsification-solvent evaporation method. The physicochemical characteristics of the nanoparticles (i.e. encapsulation efficiency, particle size distribution, morphology, in vitro release) were studied. The cellular uptake of the nanoparticles for the two human tumor cell lines: human breast carcinoma cells (MCF-7) and human carcinoma cervices cells (HeLa), was evaluated by fluorescence microscopy and transmission electronic microscopy. Cell viability was measured by the ability of single cell to form colonies in vitro. The prepared nanoparticles were spherical in shape with size between 90 nm and 190 nm. The encapsulation efficiency was 20.06%. The drug release pattern exhibited an initial burst followed by a plateau for over 24 h. The cellular uptake of nanoparticles was observed. Co-culture of MCF-7 and HeLa cells with SR-2508 loaded nanoparticles showed that released SR-2508 retained its bioactivity and effectively sensitized two hypoxic tumor cell lines to radiation. The radiosensitization of SR-2508 loaded nanoparticles was more significant than that of free drug.

Cellular uptake and radiosensitization of SR-2508 loaded PLGA nanoparticles

International Nuclear Information System (INIS)

Jin Cheng; Bai Ling; Wu Hong; Teng Zenghui; Guo Guozhen; Chen Jingyuan

2008-01-01

SR-2508 (etanidazole), a hypoxic radiosensitizer, has potential applications in radiotherapy. The poly(d,l-lactide-co-glycolide)(PLGA) nanoparticles containing SR-2508 were prepared by w/o/w emulsification-solvent evaporation method. The physicochemical characteristics of the nanoparticles (i.e. encapsulation efficiency, particle size distribution, morphology, in vitro release) were studied. The cellular uptake of the nanoparticles for the two human tumor cell lines: human breast carcinoma cells (MCF-7) and human carcinoma cervices cells (HeLa), was evaluated by fluorescence microscopy and transmission electronic microscopy. Cell viability was measured by the ability of single cell to form colonies in vitro. The prepared nanoparticles were spherical in shape with size between 90 nm and 190 nm. The encapsulation efficiency was 20.06%. The drug release pattern exhibited an initial burst followed by a plateau for over 24 h. The cellular uptake of nanoparticles was observed. Co-culture of MCF-7 and HeLa cells with SR-2508 loaded nanoparticles showed that released SR-2508 retained its bioactivity and effectively sensitized two hypoxic tumor cell lines to radiation. The radiosensitization of SR-2508 loaded nanoparticles was more significant than that of free drug.

Large effect of columnar defects on the thermodynamic properties of Bi2Sr2CaCu2O8 single crystals

Science.gov (United States)

van der Beek, C. J.; Konczykowski, M.; Li, T. W.; Kes, P. H.; Benoit, W.

1996-07-01

The introduction of columnar defects by irradiation with 5.8-GeV Pb ions is shown to affect significantly the reversible magnetic properties of Bi2Sr2CaCu2O8+δ single crystals. Notably, the suppression of superconducting fluctuations on length scales greater than the separation between columns leads to the disappearance of the ``crossing point'' in the critical fluctuation regime. At lower temperatures, the strong modification of the vortex energy due to pinning leads to an important change of the reversible magnetization. The analysis of the latter permits the direct determination of the pinning energy.

Thermally activated flux flow effects in single crystalline Bi2Sr2CaCu2O8 observed via magnetic measurements

International Nuclear Information System (INIS)

Vandenberg, J.; Vanderbeek, C.J.; Koorevaar, P.; Kes, P.H.; Mydosh, J.A.; Menken, M.J.V.; Menovsky, A.A.

1989-01-01

In this paper the authors present time-dependent magnetization and high-temperature, low-field critical-current measurements on single crystalline Bi 2 Sr 2 CaCu 2 O 8 . A short introduction to thermally activated flux-flow theory (TAFF) is given based on solving a continuity equation for fluxlines with several boundary conditions. A comparison between this theory and experiments indicates the self consistency of the TAFF model, by relating the temperature dependences of J c and of the typical relaxation time τ 0 of M(t). Furthermore, values for the pinning potential U are obtained at several temperatures

Mid - infrared transmission of polycrystalline (LaSr) (MnNi)O3

International Nuclear Information System (INIS)

Laksanawati, W. D.; Kurniawan, B.; Saptari, S. A.

2016-01-01

Polycrystalline (LaSr)(MnNi)O 3 was shintesized using sol gel methods with nitrat precursors La(NO 3 ) 3 , Sr(NO 3 ) 2 , Mn(NO 3 ) 2 .4H 2 O, and Ni(NO3)2.6H2O and the different heating process. Sample (LaSr)(MnNi)O 3 with chemical formulation La 0,67 Sr 0,33 Mn 1-x Ni x O 3 with × = 0,05 and 0,10. We report the crystallite structure of La 0,67 Sr 0,33 Mn 1-x Ni x O 3 with x= 0,00 and 0,10 are single phase with characterization by X-ray diffraction. Refinement has result that crystallite size of La 0,67 Sr 0,33 Mn 0,95 Ni 0,05 O 3 is 24,67 and La 0,67 Sr 0,33 Mn 0,9 Ni 0,1 O 3 is 21,84 with crystallite system rombohedral, it show us that increasing at Ni composition influence of decreased crystallite size. Sampel (LaSr)(MnNi)O3 has been characterization with Fourier Transform Infrared with range of wave number from 450 to 4000 cm -1 were chategories at mid infrared wave. The FTIR pattern show to us that the Mn-O-Mn bounded has absorp infrared at wave number 605 cm -1 and the dominant peak at wave number 3750 cm -1 caused the hidroxy compound in sampel La 0,67 Sr 0,33 Mn 0,95 Ni 0,05 O 3 . (paper)

Wenckebach upper rate response in single chamber pacemaker.

Science.gov (United States)

Barold, S S

2000-07-01

The Medtronic Minix pacemaker during normal function in the VVT mode was found to exhibit a Wenckenbach upper rate response similar to that of dual chamber devices. This behavior occurred only when the upper rate interval was longer than the pacemaker refractory period. In a single chamber device this response may simulate pacemaker malfunction.

Study on sorption capacity and characterization of Sr2+ on synthetic zeolite

International Nuclear Information System (INIS)

Wang Jinming; Yi Facheng

2010-01-01

Sr 2+ adsorption capacity of synthetic zeolite(ZF) are studied with the intermittence method, and ZF adsorbed the Sr 2+ is characterized and analyzed by XRD, as a reference for the evaluation of the disposal effectiveness of low and medium radwastes. The results show that Sr 2+ adsorption capacity of ZF is good, and the equilibrium time for ZF to adsorb Sr 2+ is in range of 5-14 days. Sr 2+ concentration has the greatest effect on ZF adsorption capacity,and the medium,temperature and pH value of the solution also have effect on ZF adsorption capacity. With the augment of Sr 2+ concentration,the Sr 2+ equilibrium adsorption quantity of ZF increases,but the equilibrium adsorption rate and equilibrium adsorption ratio decreases. Sr 2+ adsorption capacity of ZF improves with the augment of pH value. Sr 2+ adsorption capacity of ZF is complicate and varies with the different ion, concentration and other components in the medium solution. Sr 2+ adsorption capacity of ZF increases with the augment of temperature. As a whole, when Sr 2+ concentration in the solution is 0.005mol/L, the pH value of the solution, and the temperature of medium and solution have less effect on the Sr 2+ adsorption capacity of ZF, and the unit cell parameter of ZF adsorbed Sr 2+ decreases. (authors)

Isotope ratio 87Sr/86Sr in limestones from Bambui group, Brazil (MG)

International Nuclear Information System (INIS)

Kawashita, K.; Mizusaki, A.M.P.; Kiang, C.H.

1987-01-01

The Sr composition of ancient seawater can be estimated from the analysis of carbonate rocks and, in some cases, used to estimate the age of the analyzed carbonate. The normalized 87Sr/86Sr ratios in calcium carbonate fractions from 14 core samples in the Bambui Group near Montalvania, MG, were found to range between .7077 and .7280. The higher values are attributable to Sr isotopic exchange between silicate and carbonate phases during diagenesis. The ratio of .7077 obtained in two pure calcium carbonate samples is here suggested as the best aproximation for the 87Sr/86Sr value for the Bambui sea. This ratio is compatible with an age of about 700 Ma., estimated from the published 87Sr/86Sr curve of Veizer and others, an age in accordance with Quadros recent (1987, in preparation) identification of marine acritarchs from the latest Precambrian (Vendian). (author) [pt

Optical anisotropy of Bi2Sr2CaCu2O8

Science.gov (United States)

Kim, J. H.; Bozovic, I.; Mitzi, D. B.; Kapitulnik, A.; Harris, J. S., Jr.

1990-04-01

The optical anisotropy of Bi2Sr2CaCu2O8 in the 0.08-0.5-eV region is investigated by polarized reflectance measurements on single crystals. A very large anisotropy is found in this spectral region. The in-plane reflectance exhibits metallic behavior, while the c-axis reflectance exhibits insulatorlike behavior. This result is consistent with the large anisotropy found in the resistivity of Bi2Sr2CaCu2O8. Our spectroscopic data suggest that Bi2Sr2CaCu2O8 is a quasi-two-dimensional metal similar to La2-xSrxCuO4.

90Sr content in the Black Sea bottom sediments after the Chernobyl NPP accident and its use as a radiotracer for an assessment of bottom settlement rate

International Nuclear Information System (INIS)

Mirzoyeva, N. Y.; Egorov, V. N.; Polikarpov, G. G.

2006-01-01

radioactive fall outs, connected with nuclear weapon tests in the environments, as well as a radioactive pollution of water ecosystems after the Chernobyl NPP accident. These obtained results allow us to supply the dating on 9 0Sr the 1 37Cs method on estimation of the Black Sea bottom sediments settlement rate, which is developed earlier in RChBD (Radiation and Chemical Biology Department)

Single i.v. ketamine augmentation of newly initiated escitalopram for major depression: results from a randomized, placebo-controlled 4-week study.

Science.gov (United States)

Hu, Y-D; Xiang, Y-T; Fang, J-X; Zu, S; Sha, S; Shi, H; Ungvari, G S; Correll, C U; Chiu, H F K; Xue, Y; Tian, T-F; Wu, A-S; Ma, X; Wang, G

2016-02-01

While oral antidepressants reach efficacy after weeks, single-dose intravenous (i.v.) ketamine has rapid, yet time-limited antidepressant effects. We aimed to determine the efficacy and safety of single-dose i.v. ketamine augmentation of escitalopram in major depressive disorder (MDD). Thirty outpatients with severe MDD (17-item Hamilton Rating Scale for Depression total score ⩾ 24) were randomized to 4 weeks double-blind treatment with escitalopram 10 mg/day+single-dose i.v. ketamine (0.5 mg/kg over 40 min) or escitalopram 10 mg/day + placebo (0.9% i.v. saline). Depressive symptoms were measured using the Montgomery-Asberg Depression Rating Scale (MADRS) and the Quick Inventory of Depressive Symptomatology - Self-Report (QIDS-SR). Suicidal ideation was evaluated with the QIDS-SR item 12. Adverse psychopathological effects were measured with the Brief Psychiatric Rating Scale (BPRS)-positive symptoms, Young Mania Rating Scale (YMRS) and Clinician Administered Dissociative States Scale (CADSS). Patients were assessed at baseline, 1, 2, 4, 24 and 72 h and 7, 14, 21 and 28 days. Time to response (⩾ 50% MADRS score reduction) was the primary outcome. By 4 weeks, more escitalopram + ketamine-treated than escitalopram + placebo-treated patients responded (92.3% v. 57.1%, p = 0.04) and remitted (76.9% v. 14.3%, p = 0.001), with significantly shorter time to response [hazard ratio (HR) 0.04, 95% confidence interval (CI) 0.01-0.22, p escitalopram + placebo, escitalopram + ketamine was associated with significantly lower MADRS scores from 2 h to 2 weeks [(peak = 3 days-2 weeks; effect size (ES) = 1.08-1.18)], QIDS-SR scores from 2 h to 2 weeks (maximum ES = 1.27), and QIDS-SR suicidality from 2 to 72 h (maximum ES = 2.24). Only YMRS scores increased significantly with ketamine augmentation (1 and 2 h), without significant BPRS or CADSS elevation. Single-dose i.v. ketamine augmentation of escitalopram was safe and effective in severe MDD, holding promise for speeding up

Competitive radiation-induced carcinogenesis: an analysis of data from beagle dogs exposed to 226Ra and 90Sr

International Nuclear Information System (INIS)

Momeni, M.H.

1979-01-01

The incidence of radiation-induced primary bone sarcoma and myeloproliferative diseases was studied as a function of dose rate and time in beagles that were fed diets containing 90 SrCl 2 in equilibrium with 90 Y from midgestation to 1.5 yr of age or that were administered eight intravenous injections of 226 RaCl 2 (one injection every 2 weeks for 4 months) starting at 14 months of age. Analysis of incidence of each disease in 776 beagles showed a normal probability density function with respect to time. Median incidence time and standard deviation from the mean of distribution were calculated for primary osteosarcoma at each level of administered radioactivity. The median incidence age (T) for mortality from primary osteosarcoma increased from 4.1 yr of age, 2.6 yr after final injection of radium, for beagles injected (A 0 ) with 83.6 μCi 226 Ra, to 11.5 yr of age for beagles given A 0 = 3.14 μCi 226 Ra. A similar increase in T was observed for beagles that ingested a daily diet containing 90 Sr + 90 Y, from T = 2.8 yr of age at 36 μCi 90 Sr/day to 12.6 yr at 4 μCi 90 Sr/day. Tumor yield was calculated assuming that the causes of death from competing diseases were mutually exclusive with respect to individual diseases. Incidence and cumulative incidence for each of the diseases were calculated as a function of time and maximum dose rate. These analyses were extended to beagles administered 226 Ra by a single injection or 90 Sr by injection and inhalation. Extrapolation of the observed dose effects to lower levels of administered radioactivity (comparable to maximum permissible body burden) is discussed within the framework of a competitive mortality. (author)

Emission of 89/90Sr in the waste air of nuclear power plants with LWR in West Germany

International Nuclear Information System (INIS)

Gesewsky, P.; Riedel, H.

1977-12-01

In particular the data of Sr-90 concentrations in the gaseous effluent are given for the years 1975 up to 1977 whereas the data for Sr-89 concentrations are given for the year 1977 only. The Sr is radiochemically separated after dissolution of the aerosol filters and Sr-89 and Sr-90 are measured by two countings on a low-level β-counter. (Single separation method). From this measurements the following average emissionrates, based on a power generation of 1 GWa were calculated: BWR's: 3,0 .(period on line) 10 -4 Ci Sr-89, 2,0 .(period on line) 10 -5 Ci Sr-90; PWR's: -6 Ci Sr-90, -5 Ci-Sr-89. In comparison to the emission of long-lived radioactive aerosols with the airborne effluent of light water cooled power reactors the Sr-90 contribution is clearly below 1% usually assumed in safety calculations. (orig./HP) [de

Development of an on-line flow injection Sr/matrix separation method for accurate, high-throughput determination of Sr isotope ratios by multiple collector-inductively coupled plasma-mass spectrometry.

Science.gov (United States)

Galler, Patrick; Limbeck, Andreas; Boulyga, Sergei F; Stingeder, Gerhard; Hirata, Takafumi; Prohaska, Thomas

2007-07-01

This work introduces a newly developed on-line flow injection (FI) Sr/Rb separation method as an alternative to the common, manual Sr/matrix batch separation procedure, since total analysis time is often limited by sample preparation despite the fast rate of data acquisition possible by inductively coupled plasma-mass spectrometers (ICPMS). Separation columns containing approximately 100 muL of Sr-specific resin were used for on-line FI Sr/matrix separation with subsequent determination of (87)Sr/(86)Sr isotope ratios by multiple collector ICPMS. The occurrence of memory effects exhibited by the Sr-specific resin, a major restriction to the repetitive use of this costly material, could successfully be overcome. The method was fully validated by means of certified reference materials. A set of two biological and six geological Sr- and Rb-bearing samples was successfully characterized for its (87)Sr/(86)Sr isotope ratios with precisions of 0.01-0.04% 2 RSD (n = 5-10). Based on our measurements we suggest (87)Sr/(86)Sr isotope ratios of 0.713 15 +/- 0.000 16 (2 SD) and 0.709 31 +/- 0.000 06 (2 SD) for the NIST SRM 1400 bone ash and the NIST SRM 1486 bone meal, respectively. Measured (87)Sr/(86)Sr isotope ratios for five basalt samples are in excellent agreement with published data with deviations from the published value ranging from 0 to 0.03%. A mica sample with a Rb/Sr ratio of approximately 1 was successfully characterized for its (87)Sr/(86)Sr isotope signature to be 0.718 24 +/- 0.000 29 (2 SD) by the proposed method. Synthetic samples with Rb/Sr ratios of up to 10/1 could successfully be measured without significant interferences on mass 87, which would otherwise bias the accuracy and uncertainty of the obtained data.

Strain dependence of interfacial antiferromagnetic coupling in La0.7Sr0.3MnO3/SrRuO3 superlattices

Science.gov (United States)

Das, Sujit; Herklotz, Andreas; Pippel, Eckhard; Guo, Er-Jia; Rata, Diana; Dörr, Kathrin

2015-03-01

We have investigated the magnetic response of La0.7Sr0.3MnO3/SrRuO3 superlattices to biaxial in-plane strain applied in-situ. Superlattices grown on piezoelectric substrates of 0.72PbMg1/3Nb2/3O3-0.28PbTiO3(001) (PMN-PT) show strong antiferromagnetic coupling of the two ferromagnetic components. The coupling field of μ0HAF = 1.8 T is found to change by μ0 ΔHAF / Δɛ ~ -520 mT %-1 under reversible biaxial strain (Δɛ) at 80 K in a [La0.7Sr0.3MnO3(22 Å)/SrRuO3(55 Å)]15 superlattice. This reveals a significant strain effect on interfacial coupling. The applied in-plane compression enhances the ferromagnetic order in the manganite layers which are under as-grown tensile strain. It is thus difficult to disentangle the contributions from strain-dependent antiferromagnetic Mn-O-Ru interface coupling and Mn-O-Mn ferromagnetic double exchange near the interface, since the enhanced magnetic order of Mn spins leads to a larger net coupling of SrRuO3 layers at the interface. We discuss our experimental findings taken into account both the strain-dependent orbital occupation in a single-ion picture and the enhanced Mn order at the interface. This work was supported by the DFG within the Collaborative Research Center SFB 762 ``Functionality of Oxide Interfaces.''

Observation of field-induced long-range order in disordered Sr14Cu24O41

International Nuclear Information System (INIS)

Ohsugi, S.; Matsumoto, S.; Kitaoka, Y.; Matsuda, M.; Uehara, M.; Nagata, T.; Akimitsu, J.

2004-01-01

Field-induced magnetic order in a structural disordered single-crystal Sr 14 Cu 24 O 41 (Sr 14 -B) has been observed in the Cu-nuclear magnetic resonance (NMR) measurements for the ladder sites below 20 K under the magnetic field H∼11 T. For the Zhang Rice (ZR) sites in the chains, the spectrum splits below 20 K due to an appearance of the internal field, whereas that of less disordered Sr 14 -A does not. This gives an evidence of three-dimensional (3D) long-range (LR) ordering in Sr 14 -B below T N ∼20 K under H∼11 T

Radioecological studies of {sup 90}Sr in limnological ecosystems. Accumulation and excretion of {sup 85}Sr in goldfish, Carassius auratus auratus, rearing in the radioactive freshwater

Energy Technology Data Exchange (ETDEWEB)

Miyake, Sadaaki [Saitama Inst. of Public Health (Japan); Izumo, Yoshiro [Association of Public Health Promotion, Wako, Saitama (Japan)

2003-01-01

Accumulation and excretion of {sup 85}Sr in goldfish, Carassius auratus auratus, rearing in the radioactive freshwater were investigated in order to elucidate the accumulation mechanism of {sup 90}Sr in naturally living fishes. The accumulation of {sup 85}Sr, expressed in concentration ratio (CR) between fish and water, in whole body of the fish showed a increasing tendency with the rearing time, and the CR value reached 5.4{+-}0.4 (mean{+-}standard error) at 7th day. On the other hand, the excretion of {sup 85}Sr, expressed in retention rate, in whole body rearing in non-radioactive freshwater following the accumulation above the 7 days demonstrated a rapid decreasing at first few days, and then a gradual decreasing tendency indicating the biological half lives about 4 days and 205 days, respectively. The retention rate resulted in nearly 75% of initial radioactivity, i.e. 25% of excretion, at 25th day. As for the tissues and organs, the CR values of {sup 85}Sr reared in the radioactive freshwater for 7 days were 62.3 (vertebra: bone), 31.1 (scale), 12.5 (gill), 0.6 (viscera) and 0.4 (muscle). On the other hand, higher excretion was found in the viscera and the muscle than that in the bone, the scale and the gill. It is so suggested that the metabolic turnover rate of this radionuclide is different among these tissues and organs particularly characterizing higher accumulation and lower excretion in the vertebra (bone) and scale. (author)

β-Adrenergic induced SR Ca2+ leak is mediated by an Epac-NOS pathway.

Science.gov (United States)

Pereira, Laëtitia; Bare, Dan J; Galice, Samuel; Shannon, Thomas R; Bers, Donald M

2017-07-01

Cardiac β-adrenergic receptors (β-AR) and Ca 2+ -Calmodulin dependent protein kinase (CaMKII) regulate both physiological and pathophysiological Ca 2+ signaling. Elevated diastolic Ca 2+ leak from the sarcoplasmic reticulum (SR) contributes to contractile dysfunction in heart failure and to arrhythmogenesis. β-AR activation is known to increase SR Ca 2+ leak via CaMKII-dependent phosphorylation of the ryanodine receptor. Two independent and reportedly parallel pathways have been implicated in this β-AR-CaMKII cascade, one involving exchange protein directly activated by cAMP (Epac2) and another involving nitric oxide synthase 1 (NOS1). Here we tested whether Epac and NOS function in a single series pathway to increase β-AR induced and CaMKII-dependent SR Ca 2+ leak. Leak was measured as both Ca 2+ spark frequency and tetracaine-induced shifts in SR Ca 2+ , in mouse and rabbit ventricular myocytes. Direct Epac activation by 8-CPT (8-(4-chlorophenylthio)-2'-O-methyl-cAMP) mimicked β-AR-induced SR Ca 2+ leak, and both were blocked by NOS inhibition. The same was true for myocyte CaMKII activation (assessed via a FRET-based reporter) and ryanodine receptor phosphorylation. Inhibitor and phosphorylation studies also implicated phosphoinositide 3-kinase (PI3K) and protein kinase B (Akt) downstream of Epac and above NOS activation in this pathway. We conclude that these two independently characterized parallel pathways function mainly via a single series arrangement (β-AR-cAMP-Epac-PI3K-Akt-NOS1-CaMKII) to mediate increased SR Ca 2+ leak. Thus, for β-AR activation the cAMP-PKA branch effects inotropy and lusitropy (by effects on Ca 2+ current and SR Ca 2+ -ATPase), this cAMP-Epac-NOS pathway increases pathological diastolic SR Ca 2+ leak. This pathway distinction may allow novel SR Ca 2+ leak therapeutic targeting in treatment of arrhythmias in heart failure that spare the inotropic and lusitropic effects of the PKA branch. Copyright © 2017 Elsevier Ltd. All

Superconducting Bi-Sr-Ca-Cu-O thin films from metallo-organic complexes

International Nuclear Information System (INIS)

Gruber, H.; Krautz, E.; Fritzer, H.P.; Popitsch, A.

1991-01-01

Thin films in the Bi-Sr-Ca-Cu-O system are produced by decomposition of organic precursor compounds containing different metallo-organic complexes. The superconducting phase identified is Bi 2 Sr 2 CaCu 2 O 8+x on (100)-MgO single crystal substrates, polycrystalline Au- and Ag-ribbons and Bi 2 Sr 2 Ca 2 Cu 3 O 10+x on Ag-ribbons. For the 2212-phase a zero resistance temperature of 79 K is found. The 2223-samples on Ag-ribbons show a broad transition at 110 K with a zero resistance at 85 K. SEM and EDX are used for the detection of the microstructure and composition of the prepared films. (orig.)

Atomic layer deposited ZrO2 nanofilm on Mg-Sr alloy for enhanced corrosion resistance and biocompatibility.

Science.gov (United States)

Yang, Qiuyue; Yuan, Wei; Liu, Xiangmei; Zheng, Yufeng; Cui, Zhenduo; Yang, Xianjin; Pan, Haobo; Wu, Shuilin

2017-08-01

The biodegradability and good mechanical property of magnesium alloys make them potential biomedical materials. However, their rapid corrosion rate in the human body's environment impairs these advantages and limits their clinical use. In this work, a compact zirconia (ZrO 2 ) nanofilm was fabricated on the surface of a magnesium-strontium (Mg-Sr) alloy by the atomic layer deposition (ALD) method, which can regulate the thickness of the film precisely and thus also control the corrosion rate. Corrosion tests reveal that the ZrO 2 film can effectively reduce the corrosion rate of Mg-Sr alloys that is closely related to the thickness of the film. The cell culture test shows that this kind of ZrO 2 film can also enhance the activity and adhesion of osteoblasts on the surfaces of Mg-Sr alloys. The significance of the current work is to develop a zirconia nanofilm on biomedical MgSr alloy with controllable thickness precisely through atomic layer deposition technique. By adjusting the thickness of nanofilm, the corrosion rate of Mg-Sr alloy can be modulated, thereafter, the degradation rate of Mg-based alloys can be controlled precisely according to actual clinical requirement. In addition, this zirconia nanofilm modified Mg-Sr alloys show excellent biocompatibility than the bare samples. Hence, this work provides a new surface strategy to control the degradation rate while improving the biocompatibility of substrates. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Pinning in the flux-line-cutting regime of Bi 2Sr 2Ca 1Cu 2O 8 single crystals at high field

Science.gov (United States)

D'Anna, G.; André, M.-O.; Indenbom, M. V.; Benoit, W.

1994-09-01

Using a low-frequency torsion pendulum we show that in a Bi 2Sr 2Ca 1Cu 2O 8 single crystal the irreversibility line Birr( T) is frequency dependent down to 10 -5 Hz in the high-field regime. The activation energy has a logarithmic field dependence, U0( B)= U∗ 1n( B∗/ B). A microscopic model for flux-line-cutting and pancake collision yields quantitative expressions for U0 and for Birr( T)= B∗ exp(- T/T∗), which reproduce the experimental data very well.

Effect of Wood Aging on Wine Mineral Composition and 87Sr/86Sr Isotopic Ratio.

Science.gov (United States)

Kaya, Ayse D; Bruno de Sousa, Raúl; Curvelo-Garcia, António S; Ricardo-da-Silva, Jorge M; Catarino, Sofia

2017-06-14

The evolution of mineral composition and wine strontium isotopic ratio 87 Sr/ 86 Sr (Sr IR) during wood aging were investigated. A red wine was aged in stainless steel tanks with French oak staves (Quercus sessiliflora Salisb.), with three industrial scale replicates. Sampling was carried out after 30, 60, and 90 days of aging, and the wines were evaluated in terms of general analysis, phenolic composition, total polysaccharides, multielement composition, and Sr IR. Li, Be, Mg, Al, Sc, Ti, V, Mn, Co, Ni, Cu, Zn, Ga, Ge, As, Rb, Sr, Y, Zr, Mo, Sb, Cs, Ba, Pr, Nd, Sm, Eu, Dy, Ho, Er, Yb, Lu, Tl, and Pb elements and 87 Sr/ 86 Sr were determined by quadrupole inductively coupled plasma mass spectrometry (Q-ICP-MS) and Na, K, Ca, and Fe by flame atomic absorption spectrometry (FAAS). Two-way ANOVA was applied to assess wood aging and time effect on Sr IR and mineral composition. Wood aging resulted in significantly higher concentrations of Mg, V, Co, Ni, and Sr. At the end of the aging period, wine exhibited statistically identical Sr IR compared to control. Study suggests that wood aging does not affect 87 Sr/ 86 Sr, not precluding the use of this parameter for wine traceability purposes.

A single 2 g oral dose of extended-release azithromycin for treatment of gonococcal urethritis.

Science.gov (United States)

Yasuda, Mitsuru; Ito, Shin; Kido, Akira; Hamano, Kiminari; Uchijima, Yutaka; Uwatoko, Noriyasu; Kusuyama, Hiroyuki; Watanabe, Akiko; Miyamura, Ryuzou; Miyata, Kazutoyo; Deguchi, Takashi

2014-11-01

We treated gonococcal urethritis in men with a single 2 g dose of azithromycin extended-release formulation (azithromycin-SR) to determine its microbiological outcomes and tolerability. We enrolled 189 Japanese men with gonococcal urethritis between April 2009 and December 2013. The patients were given a single 2 g dose of azithromycin-SR. Microbiological efficacy was evaluated by the results of the post-treatment molecular testing of Neisseria gonorrhoeae. MIC testing was performed only for pretreatment isolates of N. gonorrhoeae collected from the patients. We evaluated 130 patients for microbiological outcomes. Of these patients, 122 (93.8%) were judged to be microbiologically cured on the basis of negative test results. All isolates for which the azithromycin MICs were ≤0.25 mg/L were eradicated, whereas 5 of 12 isolates for which the MICs were 1 mg/L persisted after the treatment. Forty-six adverse events occurred in 41 patients. However, all adverse events were classified as mild. The eradication rate of N. gonorrhoeae was 93.8% in men with gonococcal urethritis treated with a single 2 g dose of azithromycin-SR. The breakpoint MIC of a 2 g dose of azithromycin-SR for gonococcal urethritis associated with clinical treatment failures appeared to be 1 mg/L. With regard to side effects of higher doses of azithromycin, the 2 g dose of azithromycin-SR appeared to improve tolerability. However, the widespread use of a high-dose regimen of azithromycin might lead to the development of further resistance to azithromycin. © The Author 2014. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Easily controlled dye doped phosphorescent OLEDs with evaporation rate in single furnace

Energy Technology Data Exchange (ETDEWEB)

Mahmoudi, Malek; Janghouri, Mohammad; Mohajerani, Ezeddin, E-mail: e-mohajerani@sbu.ac.ir

2015-04-15

Electrical and optical characteristic, surface morphology and energy transfer of Ir(ppy){sub 3}:PtTPP were studied as a function of thermal evaporation rate. We have investigated the effect of various evaporation rates for mixture of dyes using single furnace method. When the deposition rate increased from 0.5 to 5 Ǻ/s, the luminescence efficiency, current density and energy transfer of OLED increased. AFM measurements showed that the surface roughness of the Ir(ppy){sub 3}:PtTPP films decreased with increasing deposition rates. These blends show excellent red emitting guest–host system with easier deposition rate control. - Highlights: • Thermal evaporation rate is used to control the doping by using single furnace. • The advantages of using single furnace are discussed. • It is shown that the evaporation rate also affects the surface roughness.

Effect of pressure on the magnetoresistance of single crystal Nd0.5Sr0.36Pb0.14MnO3-δ

International Nuclear Information System (INIS)

Khazeni, K.; Jia, Y.X.; Lu, L.; Crespi, V.H.; Cohen, M.L.; Zettl, A.

1996-01-01

To investigate the observed huge variations in magnetoresistance between different samples of manganite perovskites we have performed the first high-pressure measurement of magnetoresistance in single crystal Nd 0.5 Sr 0.36 Pb 0.14 MnO 3-δ . Both resistivity and magnetoresistance are strongly suppressed upon application of pressure. The decrease in magnetoresistance with increasing pressure rules out substrate-induced compressive strain as a source of enhanced magnetoresistance. Instead, the magnetoresistance differences between samples are ascribed primarily to the more abrupt nature of the semiconductorlike to metallic phase transition at lower temperatures. copyright 1996 The American Physical Society

Mechanical properties, corrosion, and biocompatibility of Mg-Zr-Sr-Dy alloys for biodegradable implant applications.

Science.gov (United States)

Ding, Yunfei; Lin, Jixing; Wen, Cuie; Zhang, Dongmei; Li, Yuncang

2017-11-28

This study investigates the microstructure, mechanical properties, corrosion behavior, and biocompatibility of magnesium (Mg)-based Mg1Zr2SrxDy (x = 0, 1, 1.63, 2.08 wt %) alloys for biodegradable implant applications. The corrosion behavior of the Mg-based alloys has been evaluated in simulated body fluid using an electrochemical technique and hydrogen evolution. The biocompatibility of the Mg-based alloys has been assessed using SaSO2 cells. Results indicate that the addition of Dy to Mg-Zr-Sr alloy showed a positive impact on the corrosion behavior and significantly decreased the degradation rates of the alloys. The degradation rate of Mg1Zr2Sr1.0Dy decreased from 17.61 to 12.50 mm year -1 of Mg1Zr2Sr2.08Dy based on the hydrogen evolution. The ultimate compressive strength decreased from 270.90 MPa for Mg1Zr2Sr1Dy to 236.71 MPa for Mg1Zr2Sr2.08Dy. An increase in the addition of Dy to the Mg-based alloys resulted in an increase in the volume fraction of the Mg 2 Dy phase, which mitigated the galvanic effect between the Mg 17 Sr 2 phase and the Mg matrix, and led to an increase in the corrosion resistance of the base alloy. The biocompatibility of the Mg-based alloys was enhanced with decreasing corrosion rates. Mg1Zr2Sr2.08Dy exhibited the lowest corrosion rate and the highest biocompatibility compared with the other Mg-based alloys. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2017. © 2017 Wiley Periodicals, Inc.

Chemical weathering on the North Island of New Zealand: CO2 consumption and fluxes of Sr and Os

Science.gov (United States)

Blazina, Tim; Sharma, Mukul

2013-09-01

We present Os and Sr isotope ratios and Os, Sr and major/trace element concentrations for river waters, spring waters and rains on the North Island of New Zealand. The Os and Sr data are used to examine whether the NINZ is a significant contributor of unradiogenic Os and Sr to the oceans. Major element chemistry is used to quantify weathering and CO2 consumption rates on the island to investigate relationships between these processes and Os and Sr behavior. Chemical erosion rates and CO2 consumption rates across the island range from 44 to 555 km-2 yr-1 and 95 to 1900 × 103 mol CO2 km-2 yr-1, respectively. Strontium flux for the island range from 177 to 16,100 mol km-2 yr-1 and the rivers have an average flux normalized 87Sr/86Sr ratio of 0.7075. In agreement with the previous studies these findings provide further evidence that weathering of arc terrains contributes a disproportionally large amount of Sr to the oceans and consumes very large amounts of CO2 annually compared to their areal extent. However, the 87Sr/86Sr from the NINZ is not particularly unradiogenic and it is likely not contributing significant amounts of unradiogenic Sr to the oceans. Repeated Os analyses and bottle leaching experiments revealed extensive and variable sample contamination by Os leaching from rigorously precleaned LDPE bottles. An upper bound on the flux of Os from NINZ can nevertheless be assessed and indicates that island arcs cannot provide significant amounts of unradiogenic Os to the oceans.

Cs+ and Sr2+ adsorption selectivity of zeolites in relation to radioactive decontamination

Directory of Open Access Journals (Sweden)

M.W. Munthali

2015-09-01

Full Text Available Zeolites are used as adsorbents of cationic elements in the radioactive decontamination process of water, soil and others. We determined Cs+ and Sr2+ adsorption selectivity of some zeolites to know effective zeolite species for the decontamination of radioactive Cs and Sr. A 30 mL mixed solution containing up to 15 mg L−1 of non-radioactive Cs+ or Sr+ and up to 0.50 M of Na+ or K+ was mixed with 0.5 g of Linde-type A, Na-P1, faujasite X, faujasite Y and mordenite. Among the zeolites, mordenite had the highest Cs+ adsorption selectivity, and the selectivity had no correlation to the cation exchange capacity (CEC of the zeolites. In contrast, Sr2+ adsorption selectivity of the zeolites positively correlated with the CEC of the zeolites; Linde-type A with the highest CEC showed the highest adsorption selectivity, and its adsorption rate was more than 99.9% even in the presence of 0.5 M K+. A simulated soil decontamination experiment of Cs from a Cs-retaining vermiculite by using mordenite and that of Sr from a Sr-retaining vermiculite by using Linde-type A showed decontamination rates of more than 90%.

O 1s core levels in Bi2Sr2CaCu2O8+δ single crystals

International Nuclear Information System (INIS)

Parmigiani, F.; Shen, Z.X.; Mitzi, D.B.; Lindau, I.; Spicer, W.E.; Kapitulnik, A.

1991-01-01

High-quality Bi 2 Sr 2 CaCu 2 O 8+δ superconducting single crystals, annealed at different oxygen partial pressures, have been studied using angular-resolved x-ray photoelectron spectroscopy with a resolution higher than that used in any previous study. Two states of the oxygen, separated by ∼0.7 eV, are unambiguously observed. Examining these components at different angles makes it possible to distinguish bulk from surface components. Using this capability we discover that annealing under lower oxygen partial pressure (1 atm) results in oxygen intercalation beneath the Bi-O surface layer of the crystal, whereas for higher-pressure anneals (12 atm) additional oxygen is found on the Bi-O surfaces. This steplike intercalation mechanism is also confirmed by the changes observed in the Cu and Bi core lines as a function of the annealing oxygen partial pressure

Single-crystal X-ray diffraction study of SrGeO3 high-pressure perovskite phase at 100 K

Science.gov (United States)

Nakatsuka, Akihiko; Arima, Hiroshi; Ohtaka, Osamu; Fujiwara, Keiko; Yoshiasa, Akira

2017-10-01

Single-crystal X-ray diffraction study of SrGeO3 perovskite (cubic; space group Pmɜ¯m) synthesized at 6 GPa and 1223 K was conducted at a low temperature of 100 K. The residual electron density revealed the presence of the bonding electron at the center of the Ge-O bond, in accordance with our previous conclusion that the Ge-O bond is strongly covalent. From comparison with our previous structure-refinement result at 296 K, the mean square displacement (MSD) of the O atom in the direction of the Ge-O bond is suggested to exhibit no significant temperature dependence, in contrast to that in the direction perpendicular to the bond. Thus, the strong covalency of the Ge-O bond can have a large influence on the temperature dependence of thermal vibration of the O atom.

Epitaxial properties of ZnO thin films on SrTiO3 substrates grown by laser molecular beam epitaxy

International Nuclear Information System (INIS)

Wei, X. H.; Li, Y. R.; Zhu, J.; Huang, W.; Zhang, Y.; Luo, W. B.; Ji, H.

2007-01-01

Epitaxial ZnO thin films with different orientations have been grown by laser molecular beam epitaxy on (001)- (011)-, and (111)-orientated SrTiO 3 single-crystal substrates. The growth behavior was in situ monitored by reflection high-energy electron diffraction, and the epitaxial orientation relations were reconfirmed by ex situ x-ray diffraction measurements. In the case of ZnO on SrTiO 3 (001), four orthogonal domains coexisted in the ZnO epilayer, i.e., ZnO(110) parallel SrTiO 3 (001) and ZnO[-111] parallel SrTiO 3 . For (011)- and (111)-orientated substrates, single-domain epitaxy with c axial orientation was observed, in which the in-plane relationship was ZnO[110] parallel SrTiO 3 [110] irrespective of the substrate orientations. Additionally, the crystalline quality of ZnO on SrTiO 3 (111) was better than that of ZnO on SrTiO 3 (011) because of the same symmetry between the (111) substrates and (001) films. The obtained results can be attributed to the difference of the in-plane crystallographic symmetry. Furthermore, those alignments can be explained by the interface stress between the substrates and the films

Interim FEP report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Skagius, Kristina (ed.) [Kemakta Konsult AB, Stockholm (Sweden)

2004-08-01

This report describes the work with identification and structuring of features, events and processes (FEPs) that has been carried out within the scope of the SR-Can safety assessment up to the time of the interim reporting of the project. The overall objective of the work is to develop a database of features, events and processes in a format that would facilitate both a systematic analysis of FEPs and documentation of the FEP analysis as well as facilitate revisions and updates to be made in connection with new safety assessments. This overall objective also includes the development of procedures for a systematic FEP analysis as well as to apply these procedures in order to arrive at an SR-Can version of the FEP database. The work started by implementing the content of the SR 97 Process report into a database format suitable for import and processing of FEP information from other sources. The SR 97 version of the database was systematically audited against the NEA database with Project FEPs, version 1.2. In addition, an earlier audit of the SR 97 process report against the interaction matrices developed for a deep repository of the KBS-3 type was revisited and updated. Relevant FEPs from the audit were sorted into three main categories in the SR-Can database i) FEPs related to the initial states of the repository system, ii) FEPs related to internal processes of the repository system, and iii) FEPs related to external impacts on the repository system. These groups of FEPs were further processed for making decisions on how to handle these FEPs in the assessment. Biosphere processes were not included in the SR 97 Process report and there is thus not the same basis for updating these descriptions as for the engineered barriers and the geosphere. All biosphere FEPs from the audit have therefore been compiled in a single category in the database, but remain to be further handled. FEPs were also categorised as irrelevant or as being related to methodology on a general

Interim FEP report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Skagius, Kristina

2004-08-01

This report describes the work with identification and structuring of features, events and processes (FEPs) that has been carried out within the scope of the SR-Can safety assessment up to the time of the interim reporting of the project. The overall objective of the work is to develop a database of features, events and processes in a format that would facilitate both a systematic analysis of FEPs and documentation of the FEP analysis as well as facilitate revisions and updates to be made in connection with new safety assessments. This overall objective also includes the development of procedures for a systematic FEP analysis as well as to apply these procedures in order to arrive at an SR-Can version of the FEP database. The work started by implementing the content of the SR 97 Process report into a database format suitable for import and processing of FEP information from other sources. The SR 97 version of the database was systematically audited against the NEA database with Project FEPs, version 1.2. In addition, an earlier audit of the SR 97 process report against the interaction matrices developed for a deep repository of the KBS-3 type was revisited and updated. Relevant FEPs from the audit were sorted into three main categories in the SR-Can database i) FEPs related to the initial states of the repository system, ii) FEPs related to internal processes of the repository system, and iii) FEPs related to external impacts on the repository system. These groups of FEPs were further processed for making decisions on how to handle these FEPs in the assessment. Biosphere processes were not included in the SR 97 Process report and there is thus not the same basis for updating these descriptions as for the engineered barriers and the geosphere. All biosphere FEPs from the audit have therefore been compiled in a single category in the database, but remain to be further handled. FEPs were also categorised as irrelevant or as being related to methodology on a general

Probability distribution of dose rates in the body tissue as a function of the rhytm of Sr90 administration and the age of animals

International Nuclear Information System (INIS)

Rasin, I.M.; Sarapul'tsev, I.A.

1975-01-01

The probability distribution of tissue radiation doses in the skeleton were studied in experiments on swines and dogs. When introducing Sr-90 into the organism from the day of birth till 90 days dose rate probability distribution is characterized by one, or, for adult animals, by two independent aggregates. Each of these aggregates correspond to the normal distribution law

Coexistence of spin frozen state and persistent spin dynamics in NaSrCo{sub 2}F{sub 7} as probed by μSR and NMR

Energy Technology Data Exchange (ETDEWEB)

Dengre, Shanu; Sarkar, Rajib; Braeuninger, Sascha Albert; Brueckner, Felix; Materne, Philipp; Klauss, Hans-Henning [Institute for Solid State Physics, TU Dresden (Germany); Krizan, Jason W.; Cava, Robert J. [Department of Chemistry, Princeton University, Princeton, NJ (United States); Luetkens, Hubertus; Baines, Chris [Laboratory for Muon-Spin Spectroscopy, Paul Scherrer Institute, Villigen (Switzerland)

2016-07-01

{sup 23}Na -and {sup 19}F NMR, and μSR experiments are performed to explore the microscopic properties of NaSrCo{sub 2}F{sub 7}, which is a newly discovered magnetically frustrated pyrochlore with weak bond disorder and with a frustration index of f = 42. While {sup 23}Na and {sup 19}F NMR experiments clearly suggest the presence of quasi static field distribution below ∝3 K as reflected in the huge NMR line broadening and wipe out effect of NMR signal intensity, μSR experiments on the other hand remains passive to this spin frozen state. Both NMR and μSR results indicate the slowing down of the magnetic (spin) fluctuations upon cooling towards the NMR spin frozen state. μSR relaxation rate increases slightly below ∝ 3 K, and remains not only constant down to 20 mK, but also stands independent in longitudinal magnetic field upto 4000 G implying that the spin fluctuations are dynamic. These observations suggest the coexistence of partial spin frozen state and persistent spin dynamics in NaSrCo{sub 2}F{sub 7}.

Energy dispersions of single-crystalline Bi2.0Sr1.8Ca0.8La0.3Cu2.1O8+δ superconductors determined using angle-resolved photoelectron spectroscopy

International Nuclear Information System (INIS)

Lindberg, P.A.P.; Shen, Z.; Dessau, D.S.; Wells, B.O.; Mitzi, D.B.; Lindau, I.; Spicer, W.E.; Kapitulnik, A.

1989-01-01

Angle-resolved photoemission studies of single-crystalline La-doped Bi-Sr-Ca-Cu- 90-K superconductors (Bi 2.0 Sr 1.8 Ca 0.8 La 0.3 Cu 2.1 O 8+δ ) were performed utilizing synchrotron radiation covering the photon energy range 10--40 eV. The data conclusively reveal a dispersionless character of the valence-band states as a function of the wave-vector component parallel to the c axis, in agreement with the predictions of band calculations. Band effects are evident from both intensity modulations of the spectral features in the valence band and from energy dispersions as a function of the wave vector component lying in the basal a-b plane

Radiation defects in SrB4O7:Eu2+ crystals

International Nuclear Information System (INIS)

Yavetskiy, R.P.; Dolzhenkova, E.F.; Tolmachev, A.V.; Parkhomenko, S.V.; Baumer, V.N.; Prosvirnin, A.L.

2007-01-01

Radiation-induced defects in SrB 4 O 7 :Eu 2+ (0.033 at.%) single crystal irradiated with γ and X-ray quanta has been studied. The induced optical absorption in the 400-700 nm region has been ascribed to F + centers. The Eu 2+ ions have been shown to act simultaneously as traps and as radiative recombination centers of charge carriers. Basing on the thermally stimulated luminescence (TSL), optical absorption and photoluminescence studies of SrB 4 O 7 :Eu 2+ crystals, a TSL mechanism has been proposed associated with the decay of F + centers being in non-equivalent crystallographic positions followed by radiative recombination of charge carriers on europium ions. Various positions of localization of the radiation-induced defects in the SrB 4 O 7 crystal structure have been discussed

Verification dosimetry of intravascular 90Sr/90Y source trains

International Nuclear Information System (INIS)

Sharma, S.D.; Shanta, A.; Tripathi, U.B.; Bhatt, B.C.

2001-01-01

90 Sr/ 90 Y source trains (Novoste Beta-Cath System) are currently under clinical trials in India and abroad for intracoronary brachytherapy for prevention of restenosis. Each source train of the Beta-Cath system is supplied with a source certificate giving dose rate at the reference distance of 2 mm from the centerline of the source train. It is essential that the user should check dose rates of brachytherapy sources before its application on the patients. Dose rates and depth dose measurements for 90 Sr/ 90 Y source trains of active length 40 mm using radiochromic films in a tissue equivalent phantom have been carried out. The objectives of these measurements were (1) to verify the dose rates stated in the source certificate, and (2) to obtain relative depth dose data for treatment planning. This paper presents the results of these measurements

Learning rate and attractor size of the single-layer perceptron

International Nuclear Information System (INIS)

Singleton, Martin S.; Huebler, Alfred W.

2007-01-01

We study the simplest possible order one single-layer perceptron with two inputs, using the delta rule with online learning, in order to derive closed form expressions for the mean convergence rates. We investigate the rate of convergence in weight space of the weight vectors corresponding to each of the 14 out of 16 linearly separable rules. These vectors follow zigzagging lines through the piecewise constant vector field to their respective attractors. Based on our studies, we conclude that a single-layer perceptron with N inputs will converge in an average number of steps given by an Nth order polynomial in (t/l), where t is the threshold, and l is the size of the initial weight distribution. Exact values for these averages are provided for the five linearly separable classes with N=2. We also demonstrate that the learning rate is determined by the attractor size, and that the attractors of a single-layer perceptron with N inputs partition R N +R N

Existence of the uranyl ion at regular Sr site in U doped SrBPO5

International Nuclear Information System (INIS)

Mithlesh Kumar; Mohapatra, M.; Natarajan, V.

2014-01-01

Actinide doped alkaline earth borophosphates of the general formula MBPO 5 (M = Ca 2+ , Sr 2+ , Ba 2+ ) are of special interest due to array of defect centers that can be generated in these compounds by internal (α and γ) irradiation effects. Further, the crystalline alkaline earth borophosphates are also reported to be isostructural with stillwellite-LnBSiO 5 , which are built up by BO 4 and SiO 4 tetrahedra. This structure suggests that the host MBPO 5 should be a good matrix for luminescence investigations for suitable activator ions. The important advantages of MBPO 5 type systems are their high luminescence, moderate preparation temperature and low thermal degradation. XRD pattern of the prepared phosphor confirmed the formation of SrBPO 5 in a single phase. The presence of uranium in SrBPO 5 sample was ascertained from Energy Dispersive X-ray Fluorescence (EDXRF) measurements performed on a Jordan Valley instrument. The U content in the sample was found to be about 0.85%. An Inductively Coupled Plasma Atomic Emission Spectrometric (ICP-AES), Jobin Yvon, France was used for analysis of the sample, which showed all other metallic impurities except U to be present at concentrations below 5 :U, PL, TSL and ESR studies were conducted on the solid state route samples. PL and TSL techniques were used with a view to understand the species responsible for the luminescence and its site symmetry

GROWTH RATE DISTRIBUTION OF BORAX SINGLE CRYSTALS ON THE (001 FACE UNDER VARIOUS FLOW RATES

Directory of Open Access Journals (Sweden)

Suharso Suharso

2010-06-01

Full Text Available The growth rates of borax single crystals from aqueous solutions at various flow rates in the (001 direction were measured using in situ cell method. From the growth rate data obtained, the growth rate distribution of borax crystals was investigated using Minitab Software and SPSS Software at relative supersaturation of 0807 and temperature of 25 °C. The result shows that normal, gamma, and log-normal distribution give a reasonably good fit to GRD. However, there is no correlation between growth rate distribution and flow rate of solution.   Keywords: growth rate dispersion (GRD, borax, flow rate

Syntheses, crystal structures, NMR spectroscopy, and vibrational spectroscopy of Sr(PO{sub 3}F).H{sub 2}O and Sr(PO{sub 3}F)

Energy Technology Data Exchange (ETDEWEB)

Jantz, Stephan G.; Hoeppe, Henning A. [Lehrstuhl fuer Festkoerperchemie, Institut fuer Physik, Universitaet Augsburg (Germany); Wuellen, Leo van; Fischer, Andreas [Lehrstuhl fuer Chemische Physik und Materialwissenschaften, Institut fuer Physik, Universitaet Augsburg (Germany); Libowitzky, Eugen [Institute for Mineralogy and Crystallography, Faculty of Geosciences, Geography and Astronomy, University of Vienna (Austria); Baran, Enrique J. [Centro de Quimica Inorganica (CEQUINOR/CONICET, UNLP), Facultad de Ciencias Exactas, Universidad Nacional de La Plata (Argentina); Weil, Matthias [Institute for Chemical Technologies and Analytics, Division Structural Chemistry, Vienna University of Technology (Austria)

2016-03-15

Single crystals of Sr(PO{sub 3}F).H{sub 2}O {P2_1/c, Z = 4, a = 7.4844(2) Aa, b = 7.0793(2) Aa, c = 8.4265(2) Aa, β = 108.696(1) , V = 422.91(2) Aa"3, 2391 F_o"2, 70 parameters, R_1[F"2 > 2σ(F"2)] = 0.036; wR_2(F"2 all) = 0.049, S = 1.054} were grown from an aqueous solution by a metathesis reaction. The structure comprises [SrO{sub 8}] polyhedra and PO{sub 3}F tetrahedra that form a layered arrangement parallel to (100). The topotactic dehydration of this phase proceeds between 80 and 140 C to afford Sr(PO{sub 3}F). The monazite-type crystal structure of Sr(PO{sub 3}F) was elucidated from the X-ray powder data by simulated annealing [P2{sub 1}/c, Z = 4, a = 6.71689(9) Aa, b = 7.11774(11) Aa, c = 8.66997(13) Aa, β = 128.0063(7) , V = 326.605(8) Aa{sup 3}, R{sub p} = 0.010, R{sub wp} = 0.015, R{sub F} = 0.030]. During dehydration, the structure of Sr(PO{sub 3}F) .H{sub 2}O collapses along [100] from a layered arrangement into a framework structure, accompanied by a change of the coordination number of the Sr{sup 2+} ions from eight to nine. The magic-angle spinning (MAS) NMR and vibrational spectroscopy data of both phases are discussed. (Copyright copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Results of field studies on 90SR and stable SR soil-to-plant transfer

International Nuclear Information System (INIS)

Gerzabek, M.H.; Artner, C.; Horak, O.; Mueck, K.

1992-01-01

In 1987 and 1988 at 35 sites plants ready to harvest and the corresponding soils (0 - 20 cm) were collected for 90 Sr and stable strontium analyses. Sample preparation and measurement led to a detection limit of 0.008 Bq 90 Sr kg -1 . The 90 Sr-contamination of Austrian soils ranged from 396 to 1998 Bq m -2 . Known from literature the contribution of the Chernobyl fallout amounted to app. 25 % of the total contamination. Stable strontium contents of the soils were between 6 and 62.5 mg kg -1 . Bariumtriethanolamine extracted 17.7 to 62.3 % of the total stable Sr in soil. 90 Sr-concentrations in cereal grains ranged from 0.03 to 0.67 Bq kg -1 (fresh wight) for maize and barley, respectively. The values for other foodstuff were between 0.15 (white cabbage) and 0.91 Bq kg -1 (spinach). Stable strontium contents were between 0.079 mg kg -1 (maize) and 72.5 mg kg -1 (celery shoot). The following mean 90 Sr soil-to-plant transfer factors for cereal grains were obtained: 0.010 (maize), 0.097 (rye), 0.049 (wheat), 0.095 (barley). Transfer factors for straw were up to 50 times higher (maize). The transfer of 90 Sr into vegetables and potatoes reached the same order of magnitude compared to the cereals. In all cases soil-to-plant transfer of stable Sr was clearly lower up to 60 % of the respective values for 90 Sr. Thus natural stable strontium is less plant available than 90 Sr. The influence of soil parameters on the 90 Sr transfer into plants was examinated by correlation analyses. Increasing exchangeable calcium contents of the soils resulted in a significant reduction of Sr soil-to-barley straw transfer. (authors)

The influence of crystal anisotropy on the critical state stability and flux jump dynamics of a single crystal of La1.85Sr0.15CuO4

International Nuclear Information System (INIS)

Nabiałek, A; Wiśniewski, A; Chabanenko, V V; Vasiliev, S V; Tsvetkov, T V; Pérez-Rodríguez, F

2012-01-01

We studied the critical state stability of a large cubic sample of single-crystalline La 1.85 Sr 0.15 CuO 4 for different sample orientations with respect to the external magnetic field as well as the dynamics of the flux jumps. It is shown that thermomagnetic avalanches develop under dynamic conditions, which are characterized by the magnetic diffusivity being significantly lower than the thermal case. In this case, the critical state stability depends strongly on the cooling conditions. We compared predictions from the isothermal model and from the model for a weakly cooled sample with experimental results. In both models, the field of the first flux jump decreases with increase of the sweep rate of the external magnetic field. We also investigated the influence of the external magnetic field on the dynamics of the following stages of the thermomagnetic avalanche. It is shown that the dynamics of the flux jumps is correlated with the magnetic diffusivity, which is proportional to the flux flow resistivity. (paper)

Can one observe by μ SR the transition from uncorrelated to correlated spin fluctuations? Example: Nd1.4Ce0.2Sr0.4CuO4-δ

International Nuclear Information System (INIS)

Pinkpank, M.; Amato, A.; Gygax, F.N.; Schenck, A.; Henggeler, W.; Fischer, P.

1997-01-01

μSR-measurements in ZF and LF on Nd 1.4 Ce 0.2 Sr 0.4 CuO 4-δ show a sharp increase of the depolarisation rate (λ) below ∼ 2K. This increase can be explained by the transition from uncorrelated to correlated spin fluctuations, which is in agreement with results obtained by neutron scattering

The microstructure and composition analysis of (Ba,Sr)O.6Fe_2_1_-_X)(Mn,Ti)_xO_3 (X = 0, 0,25; and 0,5)

International Nuclear Information System (INIS)

Wisnu Ari Adi; Azwar Manaf

2010-01-01

The raw materials were BaCO_3_' srCO_3_' Fe_2O_3_' MnCO_3 and TiO_2. The compound was synthesized by a solid state reaction method. The finely mixed powder was compacted at 5000 psi into pellets. These pellets were sintered in the electric chamber furnace THERMOLYNE at 1050 °C for 15 h with a heating cycle of 5°C/min ramp rate and cooled in the furnace to room temperature. The result showed that the X-ray diffraction pattern obtained can be identified as the SrO.6Fe_2O3 single phase (ICDD PDF 33-1340) for all samples according to the Hanawalt table. The microstructure analyses showed that the particle shapes are polygonal with the varied particle sizes of 2-5 μm distributed homogeneously on the surface of the samples. The element analysis showed that the compound compositions have already suitable to expectation. It is concluded that a single phase Mn-Ti substituted (Ba,Sr)O.6Fe_2O_3 have been made successfully suitable of compound composition was expected. (author)

Cerenkov Counter for In-Situ Groundwater Monitoring of 90Sr

Directory of Open Access Journals (Sweden)

Lindsay C. Todd

2005-02-01

Full Text Available Groundwater contamination from 90Sr is an environmental challenge posed topresent and former nuclear weapons related sites. Traditional methods of extractinggroundwater samples and performing laboratory analyses are expensive, time-consumingand induce significant disposal challenges. The authors present here a prototype countercapable of measuring 90Sr groundwater concentrations in-situ at or below the drinking waterlimit of 8 pCi/liter. The 90Y daughter of 90Sr produces high-energy electrons, which cancreate Cerenkov light. Photomultiplier tubes convert the Cerenkov light into an electronicpulse, which then undergoes signal processing with standard electronics. Strontium-90concentrations near the drinking water limit can be measured in a matter of hours if it is insecular equilibrium with the 90Y daughter. The prototype counter is compact, can bedeployed in an American Standard 6-inch, well while operated by a single person, andtransmits the results to a central monitoring location.

Strain-Mediated Inverse Photoresistivity in SrRuO3/La0.7Sr0.3MnO3Superlattices

KAUST Repository

Liu, Heng-Jui

2015-12-09

© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim. In the pursuit of novel functionalities by utilizing the lattice degree of freedom in complex oxide heterostructure, the control mechanism through direct strain manipulation across the interfaces is still under development, especially with various stimuli, such as electric field, magnetic field, light, etc. In this study, the superlattices consisting of colossal-magnetoresistive manganites La0.7Sr0.3MnO3 (LSMO) and photostrictive SrRuO3 (SRO) have been designed to investigate the light-dependent controllability of lattice order in the corresponding functionalities and rich interface physics. Two substrates, SrTiO3 (STO) and LaAlO3 (LAO), have been employed to provide the different strain environments to the superlattice system, in which the LSMO sublayers exhibit different orbital occupations. Subsequently, by introducing light, we can modulate the strain state and orbital preference of LSMO sublayers through light-induced expansion of SRO sublayers, leading to surprisingly opposite changes in photoresistivity. The observed photoresistivity decreases in the superlattice grown on STO substrate while increases in the superlattice grown on LAO substrate under light illumination. This work has presented a model system that demonstrates the manipulation of orbital-lattice coupling and the resultant functionalities in artificial oxide superlattices via light stimulus. A fascinating model system of optic-driven functionalities has been achieved by artificial superlattices consisting of manganite La0.7Sr0.3MnO3 (LSMO) and photostrictive SrRuO3 (SRO). With design of different initial strain and orbital states in superlattices, we can even control the photoresistivity of the superlattices in an opposite trend that cannot be achieved in pure single film.

Internal bremsstrahlung from 89Sr and 90Sr

International Nuclear Information System (INIS)

Sayibaba, T.; Narasimha Murity, K.; Rao, C.R.; Satyaprakash; Gubbi, G.K.

1987-01-01

The internal bremsstrahlung (IB) spectra emitted in the beta-decays of 89 Sr and 90 Sr were measured with a HPGe detector and a multichannel analyser along with a standard geometrical set-up. Sufficient care has been taken to avoid spurious effects. After making all the necessary corrections, the experimental results were compared with the corresponding theoretical distributions due to Knipp and Uhlenbeck and Bloch (KUB), Lewis and Ford, Nilsson, and also due to Ford and Martin (detour theory). The total IB yields of intensity and energy from each of the isotopes in the investigated energy regions are also determined and compared with the corresponding theoretical values. The present results of IB from 89 Sr are satisfactorily accounted for by the KUB theory. In the case of 90 Sr the experimental results of IB coincide with the Coulomb-corrected theoretical distibution due to Nilsson in the energy range from 60 keV to 110 keV and Beyond 110 keV, they are found to be in excess over Nilsson's theory as well as the detour theory due to Ford and Martin up to the maximum photon energy studied, namely 350 keV

Development of theophylline sustained release dosage form based on Kollidon SR.

Science.gov (United States)

Reza, Md Selim; Quadir, Mohiuddin Abdul; Haider, Syed Shabbir

2002-01-01

Sustained release theophylline matrix tablets constituting Kollidon SR (Polyvinyl acetate and povidone based matrix retarding polymer) were developed in this study in an attempt to design a dosage form that manifests desirable release profile and thorough adherence to official monographs. Four matrix tablet formulations were prepared by dry blending and direct compression of Kollidon SR and HPMC-15cps (hydroxypropylmethylcellulose) in varying proportion with fixed percentage of theophylline. Tablets containing only Kollidon SR with the active ingredient demonstrated a rapid rate of drug release with an initial burst effect. Incorporation of HPMC-15cps in the matrix tablet prolonged the release of drug with subsequent minimization of burst effect as confirmed by mean dissolution time, T50 and Higuchi release rate data. Among the batches containing HPMC-15 cps, a direct relationship was obtained between release rate and the percentage of HPMC used. A suitable controlled release profile was obtained with the matrix tablets containing 20% Kollidon SR and 30% HPMC-15cps. The formulation showed close resemblance to commercial products and compliance with USP specification. The results were explored and explained by the difference of physico-chemical property and hydration characteristics of the polymers. In addition to this result, the exponential model was applied to characterize the drug release behaviour from polymeric systems. It was found that, Fickian release is predominant in tablets containing Kollidon SR alone and non-Fickian mechanism plays an important role in the release of drug from HPMC containing tablets with a trend towards zero-order or case II release. In vitro release profile of two commercial brands were also undertaken for comparison and modulation of the experimental batches.

Thermal exposure effects on the in vitro degradation and mechanical properties of Mg-Sr and Mg-Ca-Sr biodegradable implant alloys and the role of the microstructure.

Science.gov (United States)

Bornapour, M; Celikin, M; Pekguleryuz, M

2015-01-01

Magnesium is an attractive biodegradable material for medical applications due to its non-toxicity, low density and good mechanical properties. The fast degradation rate of magnesium can be tailored using alloy design. The combined addition of Sr and Ca results in a good combination of mechanical and corrosion properties; the alloy compositions with the best performance are Mg-0.5Sr and Mg-0.3Sr-0.3Ca. In this study, we investigated an important effect, namely thermal treatment (at 400 °C), on alloy properties. The bio-corrosion of the alloys was analyzed via in vitro corrosion tests in simulated body fluid (SBF); the mechanical properties were studied through tensile, compression and three-point bending tests in two alloy conditions, as-cast and heat-treated. We showed that 8h of heat treatment increases the corrosion rate of Mg-0.5Sr very rapidly and decreases its mechanical strength. The same treatment does not significantly change the properties of Mg-0.3Sr-0.3Ca. An in-depth microstructural investigation via transmission electron microscopy, scanning electron microscopy, electron probe micro-analysis and X-ray diffraction elucidated the effects of the thermal exposure. Microstructural characterization revealed that Mg-0.3Sr-0.3Ca has a new intermetallic phase that is stable after 8h of thermal treatment. Longer thermal exposure (24h) leads to the dissolution of this phase and to its gradual transformation to the equilibrium phase Mg17Sr2, as well as to a loss of mechanical and corrosion properties. The ternary alloy shows better thermal stability than the binary alloy, but the manufacturing processes should aim to not exceed exposure to high temperatures (400 °C) for prolonged periods (over 24 h). Copyright © 2014 Elsevier B.V. All rights reserved.

Effect of Sr/Ti Ratio on the Photocatalytic Properties of SrTiO3

International Nuclear Information System (INIS)

Sulaeman, U; Yin, S; Sato, T

2011-01-01

Since strontium titanate is a wide gap semiconductor, it requires UV light to generate the photocatalytic activities. Modification of strontium titanate to show photocatalytic activity under visible light irradiation is the essential work to efficiently utilize the sun light energy for environmental application. It is expected that the synthesis of SrTiO 3 with variation of Sr/Ti atomic ratio could induce the defect crystals having unique photocatalytic properties. The SrTiO 3 with various Sr/Ti atomic ratios were synthesized by microwave-assisted solvothermal reaction of SrCl 2 .6H 2 O and Ti(OC 3 H 7 ) 4 in KOH aqueous solutions with different atomic ratios of Sr/Ti. The products were characterized by TG-DTA, XRD and DRS. The photocatalytic activity was determined by DeNO x ability using LED lamps with the wavelengths of 627 nm (red), 530 nm (green), 445 nm (blue) and 390 nm (UV). The nanoparticles of perovskite type SrTiO 3 with the particle size of 30-40 nm were successfully synthesized. The visible light responsive photocatalytic activity was generated by adding excess amount of Sr. The photocatalytic activity in visible light could be enhanced by an increase in the Sr/Ti atomic ratio up to 1.25, indicating that the visible light responsive photocatalytic activity is due to the generation of new band gap between the conduction band and valence band of SrTiO 3 by the formation of oxygen vacancy.

Toxicity of inhaled 90SrCl2 in Beagle dogs. XIII

International Nuclear Information System (INIS)

Muggenburg, B.A.; Hahn, F.F.; Boecker, B.B.; Jones, R.K.; McClellan, R.O.; Pickrell, J.A.

1979-01-01

The metabolism, dosimetry and biological effects of inhaled 90 SrCl 2 in the Beagle dog are being studied to provide a basis for assessing the consequences of inhaling 90 Sr such as might be released in certain nuclear accidents. Seventy-two dogs were exposed to aerosols containing 90 Sr resulting in initial body burdens ranging from 2.5 to 250 μCi 90 Sr/kg body weight. To date, 60 90 Sr-exposed dogs have died or have been euthanized, six during the first 31 days after inhalation of 90 Sr with bone marrow aplasia and 54 between 585 and 5109 days after inhalation of 90 Sr. The latter group includes 32 dogs with bone-related neoplasms, two with upper respiratory tract carcinomas and five dogs with various diseases of the lower respiratory tract and heart. The other 15 dogs and diseases in organs that received little or no radiation dose, such as the gastrointestinal tract, urinary tract and the central nervous system. The skeletons of the dogs dying with bone-related neoplasms received initial radiation dose rates of 3.2 to 55 rads/day and cumulative doses to death of 2800 to 22 000 rads. Fourteen control dogs have died or been euthanized, two during the last year with mammary carcinoma and intestinal lymphosarcoma. Serial observations are continuing on the six surviving 90 Sr dogs and six controls

The inverse perovskite nitrides (Sr{sub 3}N{sub 2/3-x})Sn, (Sr{sub 3}N{sub 2/3-x})Pb, and (Sr{sub 3}N)Sb. Flux crystal growth, crystal structures, and physical properties

Energy Technology Data Exchange (ETDEWEB)

Pathak, Manisha; Bobnar, Matej; Ormeci, Alim; Prots, Yurii; Hoehn, Peter [Chemische Metallkunde, Max-Planck-Institut fuer Chemische Physik fester Stoffe, Dresden (Germany); Stoiber, Dominik; Niewa, Rainer [Institut fuer Anorganische Chemie, Universitaet Stuttgart (Germany)

2018-02-15

Black single crystals with metallic luster of (Sr{sub 3}N{sub 2/3-x})E (E = Sn, Pb) and (Sr{sub 3}N)Sb were grown in lithium flux from strontium nitride, Sr{sub 2}N, and tin, lead, or antimony, respectively. Nitrogen deficiency in the tin and the lead compound is a result of the higher ionic charge of the tetrelide ions E{sup 4-} as compared to the antimonide ion Sb{sup 3-}. In contrast to microcrystalline samples from solid state sinter reactions obtained earlier, the flux synthesis induces nitrogen order in the nitrogen deficient tetrelides. The antimony compound crystallizes as inverse cubic perovskite [a = 517.22(5) pm, Z = 1, space group Pm3m, no. 221] with fully occupied nitrogen site, whereas the nitrogen deficient tin and lead compounds exhibit partially ordered arrangements and a certain phase width in respect to nitrogen contents. For the tetrelides, the nitrogen order leads to a cubic 2 x 2 x 2 superstructure [E = Sn: a = 1045.64(8) pm for x = 0, a = 1047.08(7) pm for x = 0.08; and E = Pb: a = 1050.7(1) pm for x = 0, space group Fm3m, no. 225] as derived from single-crystal X-ray diffraction data. The metallic tetrelides show diamagnetic behavior, which is consistent with electronic structure calculations. (copyright 2018 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Regional and interspecific variation in Sr, Ca, and Sr/Ca ratios in avian eggshells from the USA.

Science.gov (United States)

Mora, Miguel A; Brattin, Bryan; Baxter, Catherine; Rivers, James W

2011-08-01

To examine regional variation in strontium (Sr), which at high concentrations may reduce eggshell quality, increase egg breakage and reproductive failure, we analyzed Sr, and calcium (Ca) concentrations and Sr/Ca ratios in eggshells from 20 avian species from California, Texas, Idaho, Kansas, and Michigan. In addition, we included data previously reported from Arizona to expand the regional comparisons and to better establish patterns of Sr, and Sr/Ca ratios in bird species across the United States. We found Sr concentrations varied significantly among regions, among species, and among foraging guilds; this variability is strongly influenced by the Sr/Ca ratios in surface water from locations close to the region where the eggshells were collected. Sr concentrations and Sr/Ca ratios were significantly higher in bird eggshells from the Volta wildlife region in the San Joaquin Valley, California and in various locales from Arizona. Sr concentrations and Sr/Ca ratios in bird eggshells from other locations in the USA were lower than those detected in these two regions. Among foraging guilds, invertivores had the highest Sr concentrations and Sr/Ca ratios and carnivores had the lowest. In general, the Sr/Ca ratio increased strongly with increasing Sr concentrations (R(2) = 0.99, P eggshells suggesting that these values could be determined from Sr/Ca ratios in water. Eggshell thickness was poorly correlated with Sr (R(2) = 0.03) but had a significant and positive correlation with Ca and was more properly correlated by a quadratic equation (R(2) = 0.50, Thickness = 2.13 - 0.02Ca - 3.07 * 10(-5)Ca(2)). Our study provides further evidence that Sr accumulates significantly in the avian eggshell, in some regions at concentrations which could be of concern for potential negative effects on reproduction. We suggest that when assessing the effects of metals on avian reproduction in regions with high Sr deposits in rock and soil, Sr concentrations in the eggshell also should be

Thermal exposure effects on the in vitro degradation and mechanical properties of Mg–Sr and Mg–Ca–Sr biodegradable implant alloys and the role of the microstructure

Energy Technology Data Exchange (ETDEWEB)

Bornapour, M., E-mail: mandana.bornapour@mail.mcgill.ca [McGill University, Materials Engineering, Montreal, QC (Canada); Celikin, M. [INRS, Energy Materials Telecommunications Research Centre, Varennes, QC (Canada); Pekguleryuz, M. [McGill University, Materials Engineering, Montreal, QC (Canada)

2015-01-01

Magnesium is an attractive biodegradable material for medical applications due to its non-toxicity, low density and good mechanical properties. The fast degradation rate of magnesium can be tailored using alloy design. The combined addition of Sr and Ca results in a good combination of mechanical and corrosion properties; the alloy compositions with the best performance are Mg–0.5Sr and Mg–0.3Sr–0.3Ca. In this study, we investigated an important effect, namely thermal treatment (at 400 °C), on alloy properties. The bio-corrosion of the alloys was analyzed via in vitro corrosion tests in simulated body fluid (SBF); the mechanical properties were studied through tensile, compression and three-point bending tests in two alloy conditions, as-cast and heat-treated. We showed that 8 h of heat treatment increases the corrosion rate of Mg–0.5Sr very rapidly and decreases its mechanical strength. The same treatment does not significantly change the properties of Mg–0.3Sr–0.3Ca. An in-depth microstructural investigation via transmission electron microscopy, scanning electron microscopy, electron probe micro-analysis and X-ray diffraction elucidated the effects of the thermal exposure. Microstructural characterization revealed that Mg–0.3Sr–0.3Ca has a new intermetallic phase that is stable after 8 h of thermal treatment. Longer thermal exposure (24 h) leads to the dissolution of this phase and to its gradual transformation to the equilibrium phase Mg{sub 17}Sr{sub 2}, as well as to a loss of mechanical and corrosion properties. The ternary alloy shows better thermal stability than the binary alloy, but the manufacturing processes should aim to not exceed exposure to high temperatures (400 °C) for prolonged periods (over 24 h). - Highlights: • Thermal exposure decreases the mechanical properties and increases the biocorrosion rate of Mg–0.5Sr. • Thermally stable globular Ca/Sr-rich phases form in the Mg–0.3Sr–0.3Ca alloy. • Mg–0.3Sr–0.3Ca

Thermal exposure effects on the in vitro degradation and mechanical properties of Mg–Sr and Mg–Ca–Sr biodegradable implant alloys and the role of the microstructure

International Nuclear Information System (INIS)

Bornapour, M.; Celikin, M.; Pekguleryuz, M.

2015-01-01

Magnesium is an attractive biodegradable material for medical applications due to its non-toxicity, low density and good mechanical properties. The fast degradation rate of magnesium can be tailored using alloy design. The combined addition of Sr and Ca results in a good combination of mechanical and corrosion properties; the alloy compositions with the best performance are Mg–0.5Sr and Mg–0.3Sr–0.3Ca. In this study, we investigated an important effect, namely thermal treatment (at 400 °C), on alloy properties. The bio-corrosion of the alloys was analyzed via in vitro corrosion tests in simulated body fluid (SBF); the mechanical properties were studied through tensile, compression and three-point bending tests in two alloy conditions, as-cast and heat-treated. We showed that 8 h of heat treatment increases the corrosion rate of Mg–0.5Sr very rapidly and decreases its mechanical strength. The same treatment does not significantly change the properties of Mg–0.3Sr–0.3Ca. An in-depth microstructural investigation via transmission electron microscopy, scanning electron microscopy, electron probe micro-analysis and X-ray diffraction elucidated the effects of the thermal exposure. Microstructural characterization revealed that Mg–0.3Sr–0.3Ca has a new intermetallic phase that is stable after 8 h of thermal treatment. Longer thermal exposure (24 h) leads to the dissolution of this phase and to its gradual transformation to the equilibrium phase Mg 17 Sr 2 , as well as to a loss of mechanical and corrosion properties. The ternary alloy shows better thermal stability than the binary alloy, but the manufacturing processes should aim to not exceed exposure to high temperatures (400 °C) for prolonged periods (over 24 h). - Highlights: • Thermal exposure decreases the mechanical properties and increases the biocorrosion rate of Mg–0.5Sr. • Thermally stable globular Ca/Sr-rich phases form in the Mg–0.3Sr–0.3Ca alloy. • Mg–0.3Sr–0.3Ca maintains

Experimental probe into adsorption of Sr, Cs in the Soil

International Nuclear Information System (INIS)

Yuan Guangyu; Bai Qingzhong

1987-12-01

There are some obstacles in researching on the adsorption patterns of Sr and Cs in soil. One of them is that it is difficult to compare and to consult between various results and data for different types and sizes of soil. For this reason, it is neccesary to do further research into adsorption patterns of Sr and Cs in single particles of soil. By using scanning electromicroscope, the microcosmic phenomena of nuclides adsorption is observed, and a possible mechanism is proposed. A certain amount of diluvial soil from Shanxi Province and a certain amount of alluvial soil from western Beijing suburban were chosen as detected samples. After determining the distributions of adsorbed Sr and Cs in varied mineral particles, it is pointed out that the defference of chemical components of various size soils effects Kd value of Sr and Cs obviously. The method for calculating Kd value of mixing samples according to the particle distribution coefficients are derived under the condition of surface adsorption as main. The authors expound that it is favourable for accuracy to select and control the particle sizes in static adsorptional experiment

Bioactive SrO-SiO2 glass with well-ordered mesopores: characterization, physiochemistry and biological properties.

Science.gov (United States)

Wu, Chengtie; Fan, Wei; Gelinsky, Michael; Xiao, Yin; Simon, Paul; Schulze, Renate; Doert, Thomas; Luo, Yongxiang; Cuniberti, Gianaurelio

2011-04-01

For a biomaterial to be considered suitable for bone repair it should ideally be both bioactive and have a capacity for controllable drug delivery; as such, mesoporous SiO(2) glass has been proposed as a new class of bone regeneration material by virtue of its high drug-loading ability and generally good biocompatibility. It does, however, have less than optimum bioactivity and controllable drug delivery properties. In this study, we incorporated strontium (Sr) into mesoporous SiO(2) in an effort to develop a bioactive mesoporous SrO-SiO(2) (Sr-Si) glass with the capacity to deliver Sr(2+) ions, as well as a drug, at a controlled rate, thereby producing a material better suited for bone repair. The effects of Sr(2+) on the structure, physiochemistry, drug delivery and biological properties of mesoporous Sr-Si glass were investigated. The prepared mesoporous Sr-Si glass was found to have an excellent release profile of bioactive Sr(2+) ions and dexamethasone, and the incorporation of Sr(2+) improved structural properties, such as mesopore size, pore volume and specific surface area, as well as rate of dissolution and protein adsorption. The mesoporous Sr-Si glass had no cytotoxic effects and its release of Sr(2+) and SiO(4)(4-) ions enhanced alkaline phosphatase activity - a marker of osteogenic cell differentiation - in human bone mesenchymal stem cells. Mesoporous Sr-Si glasses can be prepared to porous scaffolds which show a more sustained drug release. This study suggests that incorporating Sr(2+) into mesoporous SiO(2) glass produces a material with a more optimal drug delivery profile coupled with improved bioactivity, making it an excellent material for bone repair applications. Copyright © 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Reconnaissance Rb-Sr dates for the Himalayan Central Gneiss, Northwest India

International Nuclear Information System (INIS)

Powell, C. McA.; Crawford, A.R.; Armstrong, R.L.; Wynne-Edwards, H.R.; Prakash, R.

1979-01-01

Rb-Sr analysis of whole-rock samples and biotite and biotite - or muscovite - whole rock pairs suggests that the Himalayan Central Gneiss in the crystalline nappes of the Lesser Himalaya and the root zone in the High Himalaya was formed during Oligocene to mid-Miocene times by deformation and metamorphism of older rocks, including Precambrian. Four whole-rock samples from the Almora-Askot thrust sheets define an isochron of 1620 +- 90 Ma with a high initial 87 Sr/ 86 Sr ratio of 0.749 +- 0.007; other single whole-rock samples give dates in the range 268 to 1065 Ma, assuming an initial 87 Sr/ 86 Sr ratio of 0.704. These dates are considered to represent either depositional or early instructive/deformational events. Three biotite-whole rock pairs from the root zone of the Himalayan Central Gneiss in Lahaul give aqes of 16 to 19 Ma and two muscovite-whole rock pairs give similar mid-Cenozoic ages (12 and 26 Ma); two muscovite-whole rock pairs give Paleozoic ages, which suggests incomplete resetting of the muscovite by the Cenozoic metamorphism. The pattern of ages is similar to recent results from adjacent areas, and consistent with models of Himalayan tectonics involving formation of the Central Gneiss from older Indian crust during the mid-Cenozoic. (auth.)

Modulation of X ray DNA damage by SR-2508 +/- buthionine sulfoximine

International Nuclear Information System (INIS)

Kinsella, T.J.; Dobson, P.P.; Russo, A.; Mitchell, J.B.; Fornace, A.J. Jr.

1986-01-01

It has been demonstrated that glutathione (GSH) depletion with buthionine sulfoximine (BSO) potentiates SR-2508 radiosensitization in hypoxic cells. We have measured the effect of SR-2508 alone, BSO alone, and combined treatment on radiation-induced DNA strand breaks in hypoxic V79 cells using alkaline and neutral elution. DNA base damage recognized by a damage specific endonuclease from M. luteus was also studied. Hypoxic irradiation markedly reduces the efficiency of single-strand (SSB) and double-strand breaks (DSB) to 10-20% compared to oxic irradiation. Hypoxia had less effect on the efficiency of base damage (ESS). BSO treatment alone, resulting in GSH depletion to less than 5% of controls, had little effect of hypoxic-SSB, DSB, and ESS. SR-2508 (5 mM) treatment alone in hypoxic cells increased the number of SSB, DSB and ESS to approximately half of that resulting from oxic irradiation. However, the combination of BSO and SR-2508 in hypoxic cells resulted in SSB and DSB comparable to oxic irradiation. This combined treatment resulted in less effect on ESS. We conclude that the observed hypoxic radiosensitization, using clonogenic survival assays with combined BSO-SR-2508, correlates with our results assessing DNA strand breaks and base damage

Defect dependence of the irreversibility line in Bi2Sr2CaCu2O8 single crystals

Science.gov (United States)

Lombardo, L. W.; Mitzi, D. B.; Kapitulnik, A.; Leone, A.

1992-09-01

The c-axis irreversibility line (IL) of pristine single-crystal Bi2Sr2CaCu2O8 is shown to exhibit three regimes: For fields less than 0.1 T, it obeys a power law, Hirr=H0(1-Tirr/Tc)μ, where μ and H0 vary with Tc. For fields greater than 2 T, the IL becomes linear with a slope of 0.7 T/K. For intermediate fields, there is a crossover region, which corresponds to the onset of collective vortex behavior. Defects produced by proton irradiation shift the IL in all three regimes: The high-field regime moves to higher temperatures, the low-field regime moves to lower temperatures, and the crossover to collective behavior becomes obscured. A maximal increase in the irreversibility temperature in the high-field regime is found to occur at a defect density of nearly one defect per vortex core disk.

Can a single pain rating replace a multiple pain rating in third molar surgery studies? Analysis of 220 patients

NARCIS (Netherlands)

Martin, W.J.J.M.; Heymans, M.W.; Skorpil, N.E.; Forouzanfar, T.

2012-01-01

This study describes the comparison of multiple and single pain ratings in patients after surgical removal of the third molar. Correlation and agreement analysis were performed between the average pain intensity measured three times a day over a period of 7 days and one single pain rating

Magnetism and metal-insulator transition in oxygen deficient SrTiO3

Science.gov (United States)

Lopez-Bezanilla, Alejandro; Ganesh, P.; Littlewood, Peter

2015-03-01

We report new findings in the electronic structure and magnetism of oxygen vacancies in SrTiO3. By means of first-principles calculations we show that the appearance of magnetism in oxygen-deficient SrTiO3 is not determined solely by the presence of a single oxygen vacancy but by the density of free carriers and the relative proximity of the vacant sites. While an isolated vacancy behaves as a non-magnetic double donor, manipulation of the doping conditions allows the stability of a single donor state with emergent local moments. Strong local lattice distortions enhance the binding of this state. Consequently we find that the free-carrier density and strain are fundamental components to obtaining trapped spin-polarized electrons in oxygen-deficient SrTiO3, which may have important implications in the design of switchable magneto-optic devices. AL-B and PBL were supported by DOE-BES under Contract No. DE-AC02-06CH11357. PG was sponsored by the Laboratory Directed Research and Development Program of Oak Ridge National Laboratory, managed by UT- Battelle, LLC, for the US Department of Energy.

Facile Synthesis of SrCO3-Sr(OH2/PPy Nanocomposite with Enhanced Photocatalytic Activity under Visible Light

Directory of Open Access Journals (Sweden)

Alfredo Márquez-Herrera

2016-01-01

Full Text Available Pyrrole monomer was chemically polymerized onto SrCO3-Sr(OH2 powders to obtain SrCO3-Sr(OH2/polypyrrole nanocomposite to be used as a candidate for photocatalytic degradation of methylene blue dye (MB. The material was characterized by Fourier transform infrared (FTIR spectroscopy, UV/Vis spectroscopy, and X-ray diffraction (XRD. It was observed from transmission electronic microscopy (TEM analysis that the reported synthesis route allows the production of SrCO3-Sr(OH2 nanoparticles with particle size below 100 nm which were embedded within a semiconducting polypyrrole matrix (PPy. The SrCO3-Sr(OH2 and SrCO3-Sr(OH2/PPy nanocomposites were tested in the photodegradation of MB dye under visible light irradiation. Also, the effects of MB dye initial concentration and the catalyst load on photodegradation efficiency were studied and discussed. Under the same conditions, the efficiency of photodegradation of MB employing the SrCO3-Sr(OH2/PPy nanocomposite increases as compared with that obtained employing the SrCO3-Sr(OH2 nanocomposite.

Bi--Sr--Ca--Cu--O superconducting films fabricated using metal alkoxides

International Nuclear Information System (INIS)

Katayama, S.; Sekine, M.

1991-01-01

Superconducting films in the Bi--Sr--Ca--Cu--O systems were made using metal alkoxides. To prepare a dip-coating solution using a mixed alkoxide solution, insoluble Cu and Bi alkoxides were dissolved by modification with 2-dimethylaminoethanol and formation of a double alkoxide, respectively. Formation of the double alkoxides of Bi with Ca or Sr was confirmed using FT-IR and 1 H-NMR. Bi--Sr--Ca--Cu--O films on yttria-stabilized ZrO 2 and single crystal MgO(100) substrates were made using this solution. The films were closely oriented along the c-axis perpendicular to the substrate. The film on MgO(100) fired at 850 degree C for 48 h showed two resistance drops around 115 and 85 K, corresponding to the high-T c and low-T c phases, respectively, and zero resistance at 72 K

Potent radiolabeled human renin inhibitor, [3H]SR42128: enzymatic, kinetic, and binding studies to renin and other aspartic proteases

International Nuclear Information System (INIS)

Cumin, F.; Nisato, D.; Gagnol, J.P.; Corvol, P.

1987-01-01

The in vitro binding of [ 3 H]SR42128 (Iva-Phe-Nle-Sta-Ala-Sta-Arg), a potent inhibitor of human renin activity, to purified human renin and a number of other aspartic proteases was examined. SR42128 was found to be a competitive inhibitor of human renin, with a K/sub i/ of 0.35 nM at pH 5.7 and 2.0 nM at pH 7.4; it was thus more effective at pH 5.7 than at pH 7.4. Scatchard analysis of the interaction binding of [ 3 H]SR42128 to human renin indicated that binding was reversible and saturable at both pH 5.7 and pH 7.4. There was a single class of binding sites, and the K/sub D/ was 0.9 nM at pH 5.7 and 1 nM at pH 7.4. The association rate was 10 times more rapid at pH 5.7 than at pH 7.4, but there was no difference between the rates of dissociation of the enzyme-inhibitor complex at the two pHs. The effect of pH on the binding of [ 3 H]SR42128 to human renin, cathepsin D, pepsin, and gastricsin was also examined over the pH range 3-8. All the aspartic proteases had a high affinity for the inhibitor at low pH. However, at pH 7.4, [ 3 H]SR42128 was bound only to human renin and to none of the other aspartic proteases. Competitive binding studies with [ 3 H]SR42128 and a number of other inhibitors on human renin or cathepsin D were used to examine the relationships between structure and activity in these systems. The study as a whole indicates that pH plays a major role in the binding of [ 3 H]SR42128 to aspartic proteases and that the nature of the inhibitor residue reacting with the renin S 2 subsites is of critical importance for the specificity of the renin-inhibitor interaction

Magnesium and cadmium in covalently-bonded Lonsdaleite networks: Synthesis, structure, and conding of AETMg{sub 2} and SrTCd{sub 2} (AE = Ca, Sr; T = Pd, Ag, Pt, Au)

Energy Technology Data Exchange (ETDEWEB)

Kersting, Marcel; Johnscher, Michael; Poettgen, Rainer [Institut fuer Anorganische und Analytische Chemie, Universitaet Muenster, Corrensstrasse 30, 48149 Muenster (Germany); Matar, Samir F. [Universite Bordeaux, ICMCB, UPR 9048, 33600 Pessac (France)

2013-04-15

The alkaline earth metal compounds AETMg{sub 2} and AETCd{sub 2} (AE = Ca, Sr; T = Pd, Ag, Pt, Au) were synthesized by induction-melting (or in muffle furnaces) of the elements in sealed niobium ampoules. The new phases were characterized by powder X-ray diffraction. The structures of SrPdMg{sub 2} and SrPdCd{sub 2} were investigated by X-ray diffraction on single crystals: MgCuAl{sub 2} type, Cmcm, a = 436.42(4), b = 1130.1(1), c = 820.54(7) pm, wR{sub 2} = 0.0115, 511 F{sup 2} values for SrPdMg{sub 2} and a = 443.5(2), b = 1063.0(2), c = 810.2(2) pm, wR{sub 2} = 0.0296, 386 F{sup 2} values for SrPdCd{sub 2} with 16 variables for each refinement. The magnesium and cadmium atoms build up [TMg{sub 2}] and [TCd{sub 2}] polyanionic networks, which leave cavities for the calcium and strontium atoms. The bonding variations within the polyanions, which are mainly influenced by the length of the b axis are discussed. Ab initio calculations of electronic structure, charge densities, and chemical bonding, characterize SrPdMg{sub 2} with a larger cohesive energy than SrPdCd{sub 2}. This is illustrated by larger bonding Pd-Mg interactions, opposite to compensating Pd-Cd between bonding and antibonding states. (Copyright copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Coral Sr-U Thermometry

Science.gov (United States)

DeCarlo, T. M.; Gaetani, G. A.; Cohen, A. L.; Foster, G. L.; Alpert, A.; Stewart, J.

2016-12-01

Coral skeletons archive the past two millennia of climate variability in the oceans with unrivaled temporal resolution. However, extracting accurate temperature information from coral skeletons is confounded by "vital effects", which often override the temperature dependence of geochemical proxies. Here, we present a new approach to coral paleothermometry based on results of abiogenic precipitation experiments interpreted within a framework provided by a quantitative model of the coral biomineralization process. We conducted laboratory experiments to test the temperature and carbonate chemistry controls on abiogenic partitioning of Sr/Ca and U/Ca between aragonite and seawater, and we modeled the sensitivity of skeletal composition to processes occurring at the site of calcification. The model predicts that temperature can be accurately reconstructed from coral skeleton by combining Sr/Ca and U/Ca ratios into a new proxy, Sr-U. We tested the model predictions with measured Sr/Ca and U/Ca ratios of fourteen Porites sp. corals collected from the tropical Pacific Ocean and the Red Sea, with a subset also analyzed using the boron isotope (δ11B) pH proxy. Observed relationships among Sr/Ca, U/Ca, and δ11B agree with model predictions, indicating that the model accounts for the key features of the coral biomineralization process. We calibrated Sr-U to instrumental temperature records and found that it captures 93% of mean annual variability (26-30 °C) and predicts temperature within 0.5 °C (1 σ). Conversely, Sr/Ca alone has an error of prediction of 1 °C and often diverges from observed temperature by 3 °C or more. Many of the problems afflicting Sr/Ca - including offsets among neighboring corals and decouplings from temperature during coral stress events - are reconciled by Sr-U. By accounting for the influence of the coral biomineralization process, the Sr-U thermometer may offer significantly improved reliability for reconstructing ocean temperatures from coral

Solar Thermochemical Energy Storage Through Carbonation Cycles of SrCO3/SrO Supported on SrZrO3.

Science.gov (United States)

Rhodes, Nathan R; Barde, Amey; Randhir, Kelvin; Li, Like; Hahn, David W; Mei, Renwei; Klausner, James F; AuYeung, Nick

2015-11-01

Solar thermochemical energy storage has enormous potential for enabling cost-effective concentrated solar power (CSP). A thermochemical storage system based on a SrO/SrCO3 carbonation cycle offers the ability to store and release high temperature (≈1200 °C) heat. The energy density of SrCO3/SrO systems supported by zirconia-based sintering inhibitors was investigated for 15 cycles of exothermic carbonation at 1150 °C followed by decomposition at 1235 °C. A sample with 40 wt % of SrO supported by yttria-stabilized zirconia (YSZ) shows good energy storage stability at 1450 MJ m(-3) over fifteen cycles at the same cycling temperatures. After further testing over 45 cycles, a decrease in energy storage capacity to 1260 MJ m(-3) is observed during the final cycle. The decrease is due to slowing carbonation kinetics, and the original value of energy density may be obtained by lengthening the carbonation steps. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Structural and intrinsic Josephson properties of Bi{sub 2}Sr{sub 2}Ca{sub 1−y}Y{sub y}Cu{sub 2}O{sub 8+δ} single crystal

Energy Technology Data Exchange (ETDEWEB)

Yamaki, K., E-mail: kyamaki@cc.utsunomiya-u.ac.jp; Murata, K.; Irie, A.

2016-10-15

Highlights: • Single crystals of yttrium-doped BSCCO (BSCYCO) were grown by a self-flux method. • T{sub c} and c-axis lattice constant of BSCYCO were controlled by the substitution of Y. • A multibranch structure was observed up to y = 0.10 (Bi{sub 2}Sr{sub 2}Ca{sub 1−y}Y{sub y}Cu{sub 2}O{sub 8+δ}). • The BSCYCO mesa has higher maximum voltage compared with nondoped BSCCO. - Abstract: In this study, Bi{sub 2}Sr{sub 2}Ca{sub 1−y}Y{sub y}Cu{sub 2}O{sub 8+δ} (BSCYCO) single crystals with yttrium doping content of y = 0–0.30 were synthesized by a self-flux method. The critical temperature and c-axis lattice constant of BSCYCO were controlled by the substitution of yttrium at the calcium site. A 290 × 90 × 0.4 µm{sup 3} mesa structure was fabricated using photolithography and argon-ion milling. A multibranch structure in current–voltage characteristics was successfully observed for mesas of BSCYCO (y = 0–0.10). The critical current of intrinsic Josephson junctions (IJJs) in BSCYCO mesas was systematically investigated.

Fabrication and Sintering Behavior of Er:SrF2 Transparent Ceramics using Chemically Derived Powder

Science.gov (United States)

Liu, Jun; Liu, Peng; Wang, Jun; Xu, Xiaodong; Li, Dongzhen; Zhang, Jian; Nie, Xinming

2018-01-01

In this paper, we report the fabrication of high-quality 5 at. % Er3+ ions doped SrF2 transparent ceramics, the potential candidate materials for a mid-infrared laser-gain medium by hot-pressing at 700 °C for 40 h using a chemically-derived powder. The phase structure, densification, and microstructure evolution of the Er:SrF2 ceramics were systematically investigated. In addition, the grain growth kinetic mechanism of Er:SrF2 was clarified. The results showed lattice diffusion to be the grain growth mechanism in the Er:SrF2 transparent ceramic of which highest in-line transmittance reached 92% at 2000 nm, i.e., very close to the theoretical transmittance value of SrF2 single crystal. Furthermore, the emission spectra showed that the strongest emission band was located at 2735 nm. This means that it is possible to achieve a laser output of approximately 2.7 μm in the 5 at. % Er3+ ions doped SrF2 transparent ceramics. PMID:29565322

Fabrication and Sintering Behavior of Er:SrF2 Transparent Ceramics using Chemically Derived Powder

Directory of Open Access Journals (Sweden)

Jun Liu

2018-03-01

Full Text Available In this paper, we report the fabrication of high-quality 5 at. % Er3+ ions doped SrF2 transparent ceramics, the potential candidate materials for a mid-infrared laser-gain medium by hot-pressing at 700 °C for 40 h using a chemically-derived powder. The phase structure, densification, and microstructure evolution of the Er:SrF2 ceramics were systematically investigated. In addition, the grain growth kinetic mechanism of Er:SrF2 was clarified. The results showed lattice diffusion to be the grain growth mechanism in the Er:SrF2 transparent ceramic of which highest in-line transmittance reached 92% at 2000 nm, i.e., very close to the theoretical transmittance value of SrF2 single crystal. Furthermore, the emission spectra showed that the strongest emission band was located at 2735 nm. This means that it is possible to achieve a laser output of approximately 2.7 μm in the 5 at. % Er3+ ions doped SrF2 transparent ceramics.

The gold-rich indide Sr{sub 5}Au{sub 13.5}In{sub 8.5}

Energy Technology Data Exchange (ETDEWEB)

Muts, Ihor [Ivan Franko National Univ. of Lviv (Ukraine). Inorganic Chemistry Dept.; Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Rodewald, Ute C.; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Zaremba, Vasyl' I. [Ivan Franko National Univ. of Lviv (Ukraine). Inorganic Chemistry Dept.

2011-11-15

The orthorhombic indide Sr{sub 5}Au{sub 13.5}In{sub 8.5} was obtained during phase-analytical studies of the Sr-Au-In system. This new indide is formed upon melting of the elements in a sealed tantalum tube. Sr{sub 5}Au{sub 13.5}In{sub 8.5} was characterized on the basis of powder and single-crystal X-ray diffraction: Pmmn, a = 476.37(9), b = 2927.5(9), c = 894.9(2) pm, wR2 = 0.056, 2355 F{sup 2} values, 87 variables. The structure is of a new type. The gold and indium atoms build up a complex three-dimensional [Au{sub 13.5}In{sub 8.5}] polyanionic network in which the strontium atoms fill channels which extend in the a direction. One site within the polyanion shows Au/In mixing. The Sr{sub 5}Au{sub 13.5}In{sub 8.5} structure is composed of SrAu{sub 3}In{sub 3-} and SrAu-related slabs. (orig.)

Synthesis and formation process of SrSO{sub 4}:Sm{sup 3+} phosphors with hierarchical structures and its electron trapping luminescence properties

Energy Technology Data Exchange (ETDEWEB)

Sun, Jiayue, E-mail: jiayue_sun@126.com; Sun, Guangchao; Xue, Bing; Cui, Dianpeng

2013-10-15

Highlights: •SrSO{sub 4} flower-like structures were synthesized by a aqueous solution route. •The as-prepared SrSO{sub 4} crystals have high crystalline. •The flower-like structures are composed of well aligned microtablets. •SrSO{sub 4} nuclei spontaneous attach by an “oriented attachment” process. •The SrSO{sub 4} crystals have excellent electron trapping luminescence properties. -- Abstract: Novel three-dimensional (3D) flower-like Strontium sulfate (SrSO{sub 4}) microstructures with hierarchical architecture were successfully fabricated by using Sr(NO{sub 3}){sub 2} react with Na{sub 2}SO{sub 4} aqueous solution under ambient conditions at room temperature. The SrSO{sub 4} flower-like microcrystals have a uniform diameter of about 10 μm, which are composed of numerous well-aligned single tablet-like SrSO{sub 4} crystals oriented radially to their center. The growth mechanism of the flower-like hierarchical celestine particles is discussed to obtain a better understanding on their formation process. XRD patterns confirm the single crystal phase of SrSO{sub 4}. In the photoluminescence property investigations of SrSO{sub 4}:Sm{sup 3+}, narrow bands observed are well identified with the electronic transition configurations of Sm{sup 3+}. The temperature-dependent photoluminescence spectra show that the temperature of maximum emission intensity is 25 °C. The thermal stability and electron trapping luminescence properties were also characterized.

CHARACTERIZATION OF THE PARTIALLY PURIFIED PLANTARCIN SR18 PRODUCED BY LACTOBACILLUS PLANTARUM SR18

Directory of Open Access Journals (Sweden)

Wagih El-Shouny

2013-04-01

Full Text Available The bacteriocin bound to the cells and that secreted into the culture filtrate of Lactobacillus plantarum SR18 were precipitated by 75% ammomium sulphate, dialysed and further purified by Gel filtration on Sephadex G-100. Bacteriocins were purified from proteins bound to the cell of L. plantarum SR18 (plantarcin SR18 a and culture filtrate proteins (plantarcin SR18 b, respectively. The SDS-PAGE of partially purified Plantarcin SR18a showed a molecular weight of 3.5 KDa. While, plantarcin SR18 b had a molecular weight of 10.3 KDa. The antibacterial activity of the tested plantarcin SR18 preparations suffered no measurable loss after 45 min at 80ºC. Whereas, At 100ºC, significant decrease in the activity of bacteriocin preparations (60- 80 % took place by the end of 45 min. At pH ranged from 5-8, the activity of the plantarcin SR18 preparations suffered no measurable loss. Dissociating agents significantly affected the bacteriocin activity. Thus, tween 80 and mercaptoethanol increased the activity of bacteriocin preparations to 1.2-1.4 fold. Sodium dodecyl sulphate (SDS increased the activity of the tested bacteriocin preparations by about 20%.The lowest residual activity (60% was recorded after treatment with Triton X100 for 45 min. Protease completely inhibited the activities of all forms of plantarcin SR18 after 45 min at 37ºC.

Investigations of 90Sr in dogs. Pt. 1

International Nuclear Information System (INIS)

Nilsson, A.; Morgan, J.P.; Book, S.A.; California Univ., Davis

1985-01-01

Purebreed beagle dogs given 90 Sr and unirradiated controls were studied for over two decades. Pregnant females were fed different doses of 90 Sr from day 21 post-conception until the offsprings reached an age of 540 days. In an additional experiment two dose levels were given in a single intravenous dose to dogs 540 days old. Radiographically the earliest skeleton lesions were characterised by small linear, solitary, cortical lucencies. These as well as tumors were more frequently noted in the higher exposure levels. They affected the appendicular skeleton almost as frequently as the axial skeleton. The lesions were predominantly found in the diaphysis, at the angle and near the acetabulum in the tubular bones, mandible and pelvis, respectively. The lesions within the diaphysis originated in the cortical bone. Histologically these lesions were characterised by different types of porosities. These could be empty or filled by a defect and/or immature, dysplastic fibrous repair tissue, within the frame of which malignant transformations seemed to take place as evidenced by malignant clones and microosteosarcomas. A comparison is made of the histologic events in dogs and mice and a tentative pathogenesis of 90 Sr induced bone tumors is discussed. (orig.)

Systematic magnetization measurements on single crystalline Bi2Sr2CaCu2O8+δ with columnar defects

International Nuclear Information System (INIS)

Kimura, Kazuhiro; Koshida, Ryo; Kwok, W.K.; Crabtree, G.W.; Okayasu, Satoru; Sataka, Masao; Kazumata, Yukio; Kadowaki, Kazuo

1999-01-01

The authors have performed systematic magnetization measurements on single crystalline Bi 2 Sr 2 CaCu 2 O 8+δ with columnar defects of B Φ = 0.005 to 1 T by using a SQUID magnetometer. Magnetization hysteresis curves of the pristine sample show a weak irreversible behavior in the vortex liquid state, suggesting the existence of the new vortex state in the vortex liquid state. This weak irreversible region persists systematically in the samples with columnar defects even up to B Φ = 1 T. It is shown that the weak hysteresis of magnetization is sensitive to the disorder level of the sample and shifts systematically to higher temperature and field region with increasing the number of columnar defects. This behavior clearly indicates that effective pinning mechanism exists even in the vortex liquid state and generates a finite critical current

Lattice instability and soft phonons in single-crystal La/sub 2-//sub x/Sr/sub x/CuO4

International Nuclear Information System (INIS)

Boeni, P.; Axe, J.D.; Shirane, G.

1988-01-01

The dispersion of the low-lying phonon branches of several doped and undoped single crystals of La/sub 2-//sub x/Sr/sub x/CuO 4 have been investigated by using inelastic-neutron-scattering techniques. The zone-center modes are in good agreement with Raman measurements. The reported peaks in the phonon density of states show up at energies that correspond to extrema in the dispersion curves of the transverse and longitudinal acoustic branches near the zone boundary. The tetragonal-to-orthorhombic phase transition is caused by a softening of transverse-optic-phonon mode at the X point. The rotational nature of the soft mode leads to moderate weak electron-phonon coupling and the mode is unlikely to enhance significantly conventional phonon mediated superconductivity. We did not observe any evidence for the predicted breathing-mode instability near the zone boundary

Magnetism in the p-type Monolayer II-VI semiconductors SrS and SrSe

Science.gov (United States)

Lin, Heng-Fu; Lau, Woon-Ming; Zhao, Jijun

2017-01-01

Using density functional theory calculations, we study the electronic and magnetic properties of the p-type monolayer II-VI semiconductors SrX (X = S,Se). The pristine SrS and SrSe monolayers are large band gap semiconductor with a very flat band in the top valence band. Upon injecting hole uniformly, ferromagnetism emerges in those system in a large range of hole density. By varying hole density, the systems also show complicated phases transition among nonmagnetic semiconductor, half metal, magnetic semiconductor, and nonmagnetic metal. Furthermore, after introducing p-type dopants in SrS and SrSe via substitutionary inserting P (or As) dopants at the S (or Se) sites, local magnetic moments are formed around the substitutional sites. The local magnetic moments are stable with the ferromagnetic order with appreciable Curie temperature. The ferromagnetism originates from the instability of the electronic states in SrS and SrSe with the large density of states at the valence band edge, which demonstrates a useful strategy for realizing the ferromagnetism in the two dimensional semiconductors. PMID:28378761

Electronic parameters of Sr2M2O7 (M = V, Nb, Ta) and Sr-O chemical bonding

DEFF Research Database (Denmark)

Atuchin, Victor V.; Grivel, Jean-Claude; Zhang, Zhaoming

2010-01-01

XPS measurements were carried out on Sr2Nb2O7 and Sr2Ta2O7 powder samples, which were synthesized using standard solid state method. The binding energy differences between the O 1s and cation core level, Δ(O-Sr) = BE(O 1s) - BE(Sr 3d5/2), was used to characterize the valence electron transfer...... on the formation of the Sr-O bonds. The chemical bonding effects were considered on the basis of our XPS results for Sr2Nb2O7 and Sr2Ta2O7 and the previously published structural and XPS data for other Sr-oxide compounds. A new empirical relationship between Δ(O-Sr) and L(Sr-O) was obtained. Possible applications...

Lifetime radiation risks from low-dose rate radionuclides in beagles

International Nuclear Information System (INIS)

Goldman, M.; Rosenblatt, L.S.

1985-01-01

One of the largest, long-term (25-yr) animal studies on the effects of low-dose internal irradiation is almost completed. Some 335 beagles were given continuous exposure to graded 90 Sr [low linear energy transfer (LET)] in their diets (D-dogs) through adulthood. A second group (R-dogs) was given fractionated doses of 225 Ra (high LET) as young adults. A third group of 44 was given a single injection of 90 Sr as adults (S-dogs) to compare single to continuous dosages. All dogs were followed through their lifetimes. Only one of the 848 dogs is still alive. The animals were whole-body counted over their entire life span and were examined frequently for assessment of medical status. There were no acute radiation lethalities. Analyses of the large data base from these dogs have begun and preliminary indications are that 90 Sr, which was tested over a 1500-fold skeletal dose rate range, does not cause significant life shortening at average accumulation skeletal doses of ∼2500 rads (25 Gy) and that a curvilinear dose response curve for life shortening was seen at higher accumulation doses. The data will be discussed in terms of modern epidemiological concepts and quantifications will be related to certain parameters of human risk from acute or chronic radiation exposures

Systematic variations of 87Sr/56Sr ratios, Sr compositions, selected major-oxide concentrations, and mineral abundances in piston cores from the Red Sea

International Nuclear Information System (INIS)

Boger, P.D.; Boger, J.L.; Faure, G.

1980-01-01

A mixing model is presented which relates the concentrations of Sr to the 87 Sr/ 86 Sr ratios and concentrations of other elements contained in a mixture of two components. The model is applied to the measured 87 Sr/ 86 Sr ratios, Sr, CaO, Fe 2 O 3 and SiO 2 concentrations of the detrital fractions of sediment from three piston cores representing different depositional environments in the Red Sea. The sediment is shown to be a mixture of two components derived from old sialic rocks and young volcanic rocks of the surrounding land masses. One of the cores contained a third component which is identified as authigenic Fe 2 O 3 . Removal of this contaminant is shown to return the system to its original detrital constituents. (Auth.)

Fill Rates of Single-Stage and Multistage Supply Systems

OpenAIRE

Matthew J. Sobel

2004-01-01

A supply system's fill rate is the fraction of demand that is met from on-hand inventory. This paper presents formulas for the fill rate of periodic review supply systems that use base-stock-level policies. The first part of the paper contains fill-rate formulas for a single-stage system and general distributions of demand. When demand is normally distributed, an exact expression uses only the standard normal distribution and density functions, and a good approximation uses only the standard ...

Addition to the analysis of the Sr VI and Sr VII spectra

International Nuclear Information System (INIS)

Wyart, J.F.

1989-01-01

Fifty-six lines of multicharged strontium are measured with an improved wavelength accuracy, or interpreted for the first time. They are 4p-4s, 4p-5s and 4p-4d transitions in Sr VII and 4p-5s transitions in Sr VI. The revision of the singlet-triplet connection in Sr VII is supported by theoretical survey of the ground configuration in Ge-like ions. (orig.)

Adsorption removal of Sr by Barium impregnated 4A Zeolite(BaA) from high radioactive seawater waste

Energy Technology Data Exchange (ETDEWEB)

Lee, Eil Hee; Lee, Keun Young; Kim, Kwang Wook; Kim, Ik Soo; Chung, Dong Yong; Moon, Jei Kwon; Choi, Jong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-06-15

This study investigated the removal of Sr, which was one of the high radioactive nuclides, by adsorption with Barium (Ba) impregnated 4A zeolite (BaA) from high-radioactive seawater waste (HSW). Adsorption of Sr by BaA (BaA-Sr), in the impregnated Ba concentration of above 20.2wt%, was decreased by increasing the impregnated Ba concentration, and the impregnated Ba concentration was suitable at 20.2wt%. The BaA-Sr adsorption was added to the co-precipitation of Sr with BaSO4 precipitation in the adsorption of Sr by 4A (4A-Sr) within BaA. Thus, it was possible to remove Sr more than 99% at m/V (adsorbent weight/solution volume)=5 g/L for BaA and m/V >20 g/L for 4A, respectively, in the Sr concentration of less than 0.2 mg/L (actual concentration level of Sr in HSW). It shows that BaA-Sr adsorption is better than 4A-Sr adsorption in for the removal capacity of Sr per unit gram of adsorbent, and the reduction of the secondary solid waste generation (spent adsorbent etc.). Also, BaA-Sr adsorption was more excellent removal capacity of Sr in the seawater waste than distilled water. Therefore, it seems to be effective for the direct removal of Sr from HSW. On the other hand, the adsorption of Cs by BaA (BaA-Cs) was mainly performed by 4A within BaA. Accordingly, it seems to be little effect of impregnated Ba into BaA. Meanwhile, BaA-Sr adsorption kinetics could be expressed the pseudosecond order rate equation. By increasing the initial Sr concentrations and the ratios of V/m, the adsorption rate constants (k2) were decreased, but the equilibrium adsorption capacities (qe) were increasing. However, with increasing the temperature of solution, k2 was conversely increased, and qe was decreased. The activation energy of BaA-Sr adsorption was 38 kJ/mol. Thus, the chemical adsorption seems to be dominant rather than physical adsorption, although it is not a chemisorption with strong bonding form.

Characteristic features of the magnetoresistance in the ferrimagnetic (Sr2FeMoO6-δ) - dielectric (SrMoO4) nanocomposite

Science.gov (United States)

Demyanov, S.; Kalanda, N.; Yarmolich, M.; Petrov, A.; Lee, S.-H.; Yu, S.-C.; Oh, S. K.; Kim, D.-H.

2018-05-01

Magnetic metal-oxide compounds with high values of magnetoresistance (MR) have attracted huge interest for spintronic applications, among which Sr2FeMoO6-δ (SFMO) has been relatively less known compared to the cobaltites and manganites, despite 100% electrons spin-polarization degree and a high Curie temperature. Here, stable fabrication and systematic analysis of nanocomposites based on SFMO with SrMoO4 dielectric sheaths are presented. SFMO-SrMoO4 nanocomposites were fabricated as follows: synthesis of the SFMO single-phase nanopowders by the modified citrate-gel technique; compaction under high pressure; thermal treatment for sheaths formation around grains. The nanocomposite is observed to exhibit a transitional behavior of conductivity from metallic, which is characteristic for the SFMO to semiconductor one in the temperature range 4 - 300K under magnetic fields up to 10T. A negative MR is observed due to the spin-polarized charge carriers tunneling through dielectric sheaths. MR value reaches 43% under 8T at 10κ. The dielectric sheaths thickness was determined to be about 10 nm by electric breakdown voltage value at current-voltage characteristics curves. The breakdown is found to be a reversible process determined by collisional ionization of dielectric atoms in strong electric field depending on knocked-out electrons from the SrMoO4. It was found that MR changes sign in electric breakdown region, revealing the giant magnetoresistive properties.

Function modification of SR-PSOX by point mutations of basic amino acids

Directory of Open Access Journals (Sweden)

Chen Chunxia

2011-04-01

Full Text Available Abstract Background Atherosclerosis (AS is a common cardiovascular disease. Transformation of macrophages to form foam cells by internalizing modified low density-lipoprotein (LDL via scavenger receptor (SR is a key pathogenic process in the onset of AS. It has been demonstrated that SR-PSOX functions as either a scavenger receptor for uptake of atherogenic lipoproteins and bacteria or a membrane-anchored chemokine for adhesion of macrophages and T-cells to the endothelium. Therefore, SR-PSOX plays an important role in the development of AS. In this study the key basic amino acids in the chemokine domain of SR-PSOX have been identified for its functions. Results A cell model to study the functions of SR-PSOX was successfully established. Based on the cell model, a series of mutants of human SR-PSOX were constructed by replacing the single basic amino acid residue in the non-conservative region of the chemokine domain (arginine 62, arginine 78, histidine 80, arginine 82, histidine 85, lysine 105, lysine 119, histidine 123 with alanine (designated as R62A, R78A, H80A, R82A, H85A, K105A, K119A and H123A, respectively. Functional studies showed that the mutants with H80A, H85A, and K105A significantly increased the activities of oxLDL uptake and bacterial phagocytosis compared with the wild-type SR-PSOX. In addition, we have also found that mutagenesis of either of those amino acids strongly reduced the adhesive activity of SR-PSOX by using a highly non-overlapping set of basic amino acid residues. Conclusion Our study demonstrates that basic amino acid residues in the non-conservative region of the chemokine domain of SR-PSOX are critical for its functions. Mutation of H80, H85, and K105 is responsible for increasing SR-PSOX binding with oxLDL and bacteria. All the basic amino acids in this region are important in the cells adhesion via SR-PSOX. These findings suggest that mutagenesis of the basic amino acids in the chemokine domain of SR-PSOX may

Luminescence of the SrCl2:Pr crystals under high-energy excitation

International Nuclear Information System (INIS)

Antonyak, O.T.; Voloshinovskii, A.S.; Vistovskyy, V.V.; Stryganyuk, G.B.; Kregel, O.P.

2014-01-01

The present research was carried out in order to elucidate the mechanisms of energy transfer from the crystal lattice to Pr 3+ ions in SrCl 2 . The luminescence excitation and emission spectra as well as luminescence kinetics of the SrCl 2 :Pr single crystals containing 0.2 mol% Pr were investigated at 300 and 10 K using the vacuum ultraviolet (VUV) synchrotron radiation. The X-ray excited luminescence spectra of the SrCl 2 :Pr (C Pr =0.2 and 0.5 mol%) and SrCl 2 :Pr, K (C Pr =1.5 mol%; C K =1.5 mol%) crystals were studied at 294 and 80 K. Under optical excitation of the samples in the Pr 3+ absorption bands, there were observed five fast ultraviolet emissions assigned to the 4f 1 5d→4f 2 transitions, and two long-wave bands corresponding to the f–f transitions. Furthermore, the intrinsic emission bands of SrCl 2 were observed at 10 K. The X-ray excited luminescence spectrum of the SrCl 2 :Pr crystal containing 0.2 mol% Pr, besides intrinsic emission band near 400 nm, has got a long-wave band at about 490 nm of the Pr 3+ centers. There were not observed any emission bands of the Pr 3+ centers corresponding to the 4f 1 5d–4f 2 transitions in the X-ray excited luminescence spectrum of the SrCl 2 :Pr crystal. The possible mechanisms of energy transfer from the SrCl 2 matrix to the Pr 3+ centers are discussed. -- Highlights: • Spectral-luminescent properties of SrCl 2 :Pr have been investigated. • The identification of emission 4f–4f and 5d–4f bands of Pr 3+ ions was performed. • Adding of potassium prevents clustering of the Pr 3+ centers in the SrCl 2 :Pr, K crystals. • Under X-ray excitation at 80–300 K only Pr 3+ 4f–4f and intrinsic emission is observed

Crystal structures of KM(AsF{sub 6}){sub 3} (M{sup 2+} = Mg, Co, Mn, Zn), KCu(SbF{sub 6}){sub 3} and [Co(HF){sub 2}]Sr[Sr(HF)]{sub 2}-[Sr(HF){sub 2}]{sub 2}[AsF{sub 6}]{sub 12}

Energy Technology Data Exchange (ETDEWEB)

Mazej, Zoran; Goreshnik, Evgeny [Jozef Stefan Institute, Ljubljana (Slovakia). Dept. of Inorganic Chemisrty and Technology

2015-05-01

The KM(AsF{sub 6}){sub 3} (M{sup 2+} = Mg, Co, Mn, Zn) and KCu(SbF{sub 6}){sub 3} compounds crystallize isotypically to previously known KNi(AsF{sub 6}){sub 3}. The main features of the structure of these compounds are rings of MF{sub 6} octahedra sharing apexes with AsF{sub 6} octahedra connected into infinite tri-dimensional frameworks. In this arrangement cavities are formed where K{sup +} cations are placed. Single crystals of CoSr{sub 5}(AsF{sub 6}){sub 12}.8HF were obtained as one of the products after the crystallization of 3KF/CoF{sub 2}/SrF{sub 2} mixture in the presence of AsF{sub 5} in anhydrous HF. The CoSr{sub 5}(AsF{sub 6}){sub 12}.8HF is monoclinic, C/2c (No.15), with a = 26.773(5) Aa, b = 10.087(2) Aa, c = 21.141(5) Aa, β = 93.296(13) {sup circle}, V = 5699.9(19) Aa{sup 3} at 200 K, and Z = 4. There are three crystallographically non-equivalent Sr{sup 2+} cations in the crystal structure of CoSr{sub 5}(AsF{sub 6}){sub 12}.8HF. The Sr1 is coordinated by ten fluorine atoms from eight different [AsF{sub 6}]- anions, meanwhile Sr2 and Sr3 are bound to nine fluorine atoms provided by one HF and eight AsF{sub 6} units or by two HF and six AsF{sub 6} units, respectively. The Co{sup 2+} is coordinated distorted-octahedrally by six fluorine atoms from two HF molecules and four different AsF{sub 6} units. All those moieties in the crystal structure of [Co(HF){sub 2}]Sr[Sr(HF)]{sub 2}[Sr(HF){sub 2}]{sub 2}[AsF{sub 6}]{sub 12} are connected into tridimensional framework. The CoSr{sub 5}(AsF{sub 6}){sub 12}.8HF is a unique example of compound where HF molecules are directly bound via fluorine atoms to two different metal centres.

Strontium (Sr) separation from seawater using titanate adsorbents: Effects of seawater matrix ions on Sr sorption behavior

Science.gov (United States)

Ryu, Jungho; Hong, Hye-jin; Ryu, Taegong; Park, In-Su

2017-04-01

Strontium (Sr) which has many industrial applications such as ferrite magnet, ceramic, and fire works exists in seawater with the concentration of approximately 7 mg/L. In previous report estimating economic potential on recovery of various elements from seawater in terms of their commercial values and concentrations in seawater, Sr locates upper than approximate break-even line, which implies Sr recovery from seawater can be potentially profitable. Recently, Sr separation from seawater has received great attention in the environmental aspect after Fukushima Nuclear Power Plant (NPP) accident which released much amount of radioactive Sr and Cs. Accordingly, the efficient separation of radioactive elements released to seawater has become critical as an important technological need as well as their removal from radioactive wastes. So far, it has been introduced to separate Sr from aqueous media by various methods including solvent extraction, adsorption by solid materials, and ion exchange. Among them, the adsorption technique using solid adsorbents is of great interest for selectively separating Sr from seawater with respect to low concentration level of Sr. In this study, we synthesized titanate nanotube (TiNT) by simple hydrothermal reaction, characterized its physicochemical properties, and systematically evaluated Sr sorption behavior under various reaction conditions corresponding to seawater environment. The synthesized TiNT exhibited the fibril-type nanotube structure with high specific surface area of 260 m2/g. The adsorption of Sr on TiNT rapidly occurred following pseudo-second-order kinetic model, and was in good agreement with Langmuir isotherm model, indicating maximum adsorption capacity of 97 mg/g. Based on Sr uptake and Na release with stoichiometric balance, sorption mechanism of Sr on TiNT was found to be ion-exchange between Na in TiNT lattice and Sr in solution phase, which was also confirmed by XRD and Raman analysis. Among competitive ions, Ca

Input of 87Sr/86Sr ratios and Sr geochemical signatures to update knowledge on thermal and mineral waters flow paths in fractured rocks (N-Portugal)

International Nuclear Information System (INIS)

Marques, J.M.; Carreira, P.M.; Goff, F.; Eggenkamp, H.G.M.; Antunes da Silva, M.

2012-01-01

Strontium isotopes and other geochemical signatures are used to determine the relationships between CO 2 -rich thermal (Chaves: 76 °C) and mineral (Vilarelho da Raia, Vidago and Pedras Salgadas: 17 °C) waters discharging along one of the major NNE–SSW trending faults in the northern part of mainland Portugal. The regional geology consists of Hercynian granites (syn-tectonic-310 Ma and post-tectonic-290 Ma) intruding Silurian metasediments (quartzites, phyllites and carbonaceous slates). Thermal and mineral waters have 87 Sr/ 86 Sr isotopic ratios between 0.716713 and 0.728035. 87 Sr/ 86 Sr vs. 1/Sr define three end-members (Vilarelho da Raia/Chaves, Vidago and Pedras Salgadas thermal and mineral waters) trending from rainfall composition towards that of the CO 2 -rich thermal and mineral waters, indicating different underground flow paths. Local granitic rocks have 87 Sr/ 86 Sr ratios of 0.735697–0.789683. There is no indication that equilibrium was reached between the CO 2 -rich thermal and mineral waters and the granitic rocks. The mean 87 Sr/ 86 Sr ratio of the thermal and mineral waters (0.722419) is similar to the Sr isotopic ratios of the plagioclases of the granitic rocks (0.71261–0.72087). The spatial distribution of Sr isotope and geochemical signatures of waters and the host rocks suggests that the thermal and mineral waters circulate in similar but not the same hydrogeological system. Results from this study could be used to evaluate the applicability of this isotope approach in other hydrogeologic investigations.

A high 87Sr 86Sr mantle source for low alkali tholeiite, northern Great Basin

Science.gov (United States)

Mark, R.K.; Lee, Hu C.; Bowman, H.R.; Asaro, F.; McKee, E.H.; Coats, R.R.

1975-01-01

Olivine tholeiites, the youngest Tertiary units (about 8-11 m.y. old) at five widely spaced localities in northeastern Nevada, are geologically related to the basalts of the Snake River Plain, Idaho, to the north and are similar in major element and alkali chemistry to mid-ocean ridge basalts (MORB) and island arc tholeiites. The measured K (1250-3350 ppm), Rb (1??9-6??2 ppm) and Sr (140-240 ppm) concentrations overlap the range reported for MORB. Three of the five samples have low, unfractionated rare earth element (REE) patterns, the other two show moderate light-REE enrichment. Barium concentration is high and variable (100-780 ppm) and does not correlate with the other LIL elements. The rocks have 87Sr/86Sr = 0??7052-0??7076, considerably higher than MORB (~0??702-0??703). These samples are chemically distinct (i.e. less alkalic) from the olivine tholeiites from the adjacent Snake River Plain, but their Sr isotopic compositions are similar. They contain Sr that is distinctly more radiogenic than the basalts from the adjacent Great Basin. About 10 b.y. would be required for the mean measured Rb/Sr (~ 0??02) of these samples to generate, in a closed system, the radiogenic Sr they contain. The low alkali content of these basalts makes crustal contamination an unlikely mechanism. If the magma is uncontaminated, the time-averaged Rb/Sr of the source material must have been ~0??04. A significant decrease in Rb/Sr of the source material (a factor 2??) thus most probably occurred in the relatively recent (1??09 yr) past. Such a decrease of Rb/Sr in the mantle could accompany alkali depletion produced by an episode of partial melting and magma extraction. In contrast, low 87Sr 86Sr ratios indicate that the source material of the mid-ocean ridge basalts may have been depleted early in the Earth's history. ?? 1975.

Studies on the leukemogenic and immunologic effects of radiostrontium (90Sr) and x rays in mice

International Nuclear Information System (INIS)

Ito, K.; Nagao, K.; Kawamura, Y.; Yokoro, K.

1976-01-01

The leukemogenic effect of internal irradiation with radiostrontium ( 90 Sr) was compared with that of external irradiation with x rays in ICR/JCL mice. Immunological, hematological, and cytogenetical changes were also studied during the preleukemic period in mice treated with 90 Sr or with x rays. A single intraperitoneal injection of 1.0 μCi of 90 Sr per gram of body weight resulted in leukemia in 62 percent of the mice. Only one of the 90 Sr-induced leukemias was of thymic origin. The occurrence of the leukemia was not affected by thymectomy. A fractionated whole-body x-irradiation of 680 R induced leukemia in 77 percent of the mice; the majority of the leukemias were of thymic origin. Although x-irradiation over the thymic region was ineffective in eliciting leukemia, a combined treatment of 90 Sr and local x-irradiation of the thymus was effective in inducing thymic lymphomas. The single intraperitoneal administration of 90 Sr caused an enhancement of both direct and indirect splenic plaque-forming cell (PFC) responses to sheep red blood cells, lasting for 35 days after treatment. No changes were observed in delayed-type hypersensitivity to picryl chloride. Thymectomy caused no appreciable effect in these immune responses. The fractionated whole-body x-irradiation rapidly depressed both PFC and delayed-type hypersensitivity responses, which persisted for a long period, especially in thymectomized mice. An abrupt increase of chromosomally aberrant cells in the thymus 60 days after the last x-irradiation was preceded by an increase of aberrant population in the bone marrow. On the other hand, a long-lasting appearance of aberrant population in the bone marrow and lymph nodes was observed in 90 Sr-injected mice

Evidence for the quasi-two dimensional behavior of the vortex structure in Bi2Sr2CaCu2O8 single crystals

International Nuclear Information System (INIS)

Pastoriza, H.; Arribere, A.; Goffman, M.F.; Cruz, F. de la; Mitzi, D.B.; Kapitulnik, A.

1994-01-01

AC susceptibility and dc magnetization measurements on Bi 2 Sr 2 CaCu 2 O 8 (BSCCO) single crystals in a wide range of temperatures clearly show that below the dc irreversibility line the vortex system loss the long range order in the c direction. The susceptibility data taken at 7 Hz show the different nature of two dissipation peaks: One related to the interplane currents at temperatures well below the dc irreversibility line and the other associated with the intraplane ones at temperatures above that line. In this sense the irreversibility line corresponds to the temperature where quasi-two dimensional vortices are depinned. (orig.)

Single-crystal SrTiO3 fiber grown by laser heated pedestal growth method: influence of ceramic feed rod preparation in fiber quality

Directory of Open Access Journals (Sweden)

D. Reyes Ardila

1998-10-01

Full Text Available The rapidly spreading use of optical fiber as a transmission medium has created an interest in fiber-compatible optical devices and methods for growing them, such as the Laser Heated Pedestal Growth (LHPG. This paper reports on the influence of the ceramic feed rod treatment on fiber quality and optimization of ceramic pedestal processing that allows improvements to be made on the final quality in a simple manner. Using the LHPG technique, transparent crack-free colorless single crystal fibers of SrTiO3 (0.50 mm in diameter and 30-40 mm in length were grown directly from green-body feed rods, without using external oxygen atmosphere.

Identification of Marchfeld asparagus using Sr isotope ratio measurements by MC-ICP-MS.

Science.gov (United States)

Swoboda, S; Brunner, M; Boulyga, S F; Galler, P; Horacek, M; Prohaska, T

2008-01-01

This work focuses on testing and application of Sr isotope signatures for the fast and reliable authentication and traceability of Asparagus officinalis originating from Marchfeld, Austria, using multicollector inductively coupled plasma mass spectrometry after optimised Rb/Sr separation. The major sample pool comprises freeze-dried and microwave-digested asparagus samples from Hungary and Slovakia which are compared with Austrian asparagus originating from the Marchfeld region, which is a protected geographical indication. Additional samples from Peru, The Netherlands and Germany were limited in number and allowed therefore only restricted statistical evaluation. Asparagus samples from Marchfeld were harvested within two subsequent years in order to investigate the annual variation. The results show that the Sr isotope ratio is consistent within these 2 years of investigation. Moreover, the Sr isotope ratio of total Sr in soil was found to be significantly higher than in an NH4NO3 extract, reflecting the mobile (bioavailable) phase. The isotope composition in the latter extract corresponds well to the range found in the asparagus samples in Marchfeld, even though the concentration of Sr in asparagus shows no direct correlation to the concentration of Sr in the mobile phase of the soil. The major question was whether the 'Marchfelder Spargel' can be distinguished from samples from the neighbouring countries of Hungary and Slovakia. According to our findings, they can be clearly (100%) singled out from the Hungarian samples and can be distinguished from the Slovakian asparagus samples with a probability of more than 80%.

Oxide meets silicide. Synthesis and single-crystal structure of Ca{sub 21}SrSi{sub 24}O{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Reckeweg, Olaf; DiSalvo, Francis J. [Cornell Univ., Ithaca, NY (United States). Dept. of Chemistry and Chemical Biology

2017-06-01

A few black, rectangular thin plates of Ca{sub 21}SrSi{sub 24}O{sub 2} were obtained by serendipity in a solid-state reaction of calcium metal, strontium chloride and silicon powder at 1200 K for 2 days designed to produce 'Ca{sub 2}SrCl{sub 2}[Si{sub 3}]'. The title compound forms next to some CaSi and some remaining educts. Ca{sub 21}SrSi{sub 24}O{sub 2} crystallizes in the monoclinic space group C2/m (no. 12) with unit cell parameters of a=1895.2(2), b=450.63(5) and c=1397.33(18) pm and β=112.008(7) (Z=1). The title compound shows planar, eight-membered, kinked Si{sub 8} chains with Si-Si distances between 241.4 and 245.0 pm indicating bonding interactions and kinked 'rope ladders' connecting the chains with interatomic Si-Si distances in the range 268.1-274.7 pm. Embedded in between these silicon substructures are columns of oxygen centered, apex sharing [(Ca{sub 1-x} Sr{sub x}){sub 6/2}O] octahedra and calcium ions.

Sr and Nd isotopes in basalts form the East Pacific Rise: Significance for mantle heterogeneity

International Nuclear Information System (INIS)

Macdougall, J.D.; Lugmair, G.W.

1986-01-01

Isotopic data for Sr and Nd from fresh glassy East Pacific Rise basalts suggest that this part of the suboceanic mantle is characterized by subtle but distinct large-scale regional isotopic variability which may reflect differences between cells of the convecting mantle. In spite of a systematic N-S change in spreading rate of a factor of three along the sampled portion of the EPR, no correlation is observed between spreading rate and range of isotopic composition, indicating that the regional variations override homogenization effects which may be correlated with rate of magma generation and hence spreading rate. There is no clear signature in our data of effects from the postulated global ''Dupal Anomaly''. However, for a restricted ridge segment at the latitude of Easter Island, anomalously high 87 Sr/ 86 Sr and low 143 Nd/ 144 Nd occur, coupled with high incompatible element concentrations. These features are most easily understood as being the result of inclusion of a ''plume'' component in these ridge basalts. (orig.)

Synthesis of pure and Sr-doped LaGaO3, LaFeO3 and LaCoO3 and Sr,Mg-doped LaGaO3 for ITSOFC application using different wet chemical routes

International Nuclear Information System (INIS)

Kumar, M.; Srikanth, S.; Ravikumar, B.; Alex, T.C.; Das, S.K.

2009-01-01

Pure and Sr-doped LaGaO 3 , LaFeO 3 and LaCoO 3 and Sr,Mg-doped LaGaO 3 were synthesized by various wet chemical routes, namely combustion, co-precipitation and citrate-gel methods. The effect of the various process parameters on the phase purity, particle size and surface area and morphology of the synthesized powders were determined by XRD, simultaneous TG-DTA, laser light scattering, BET and scanning electron microscopy. The stability of the synthesized pure phases in oxidizing and reducing atmosphere was also studied by thermogravimetry. It was observed that pure and Sr-doped single perovskite phases of lanthanum ferrite, cobaltite and gallate and Sr,Mg-doped lanthanum gallate could be synthesized by combustion and citrate-gel methods under suitable process conditions. Synthesis using the co-precipitation method yielded incomplete reaction irrespective of the calcination temperature adopted. The citrate-gel method yielded better powder properties in terms of particle size and morphology and surface area compared to combustion synthesis. It was found that pure and Sr-doped lanthanum ferrite, lanthanum cobaltite, lanthanum gallate and Sr,Mg-doped lanthanum gallate were stable in the oxidizing atmosphere. In the reducing atmosphere, pure and Sr-doped lanthanum ferrite and Sr,Mg-doped lanthanum gallate was found to be stable at least during the timeframe of the thermogravimetric experiment whereas pure and Sr-doped lanthanum cobaltite was partially reduced in hydrogen atmosphere

Rating the methodological quality of single-subject designs and n-of-1 trials: introducing the Single-Case Experimental Design (SCED) Scale.

Science.gov (United States)

Tate, Robyn L; McDonald, Skye; Perdices, Michael; Togher, Leanne; Schultz, Regina; Savage, Sharon

2008-08-01

Rating scales that assess methodological quality of clinical trials provide a means to critically appraise the literature. Scales are currently available to rate randomised and non-randomised controlled trials, but there are none that assess single-subject designs. The Single-Case Experimental Design (SCED) Scale was developed for this purpose and evaluated for reliability. Six clinical researchers who were trained and experienced in rating methodological quality of clinical trials developed the scale and participated in reliability studies. The SCED Scale is an 11-item rating scale for single-subject designs, of which 10 items are used to assess methodological quality and use of statistical analysis. The scale was developed and refined over a 3-year period. Content validity was addressed by identifying items to reduce the main sources of bias in single-case methodology as stipulated by authorities in the field, which were empirically tested against 85 published reports. Inter-rater reliability was assessed using a random sample of 20/312 single-subject reports archived in the Psychological Database of Brain Impairment Treatment Efficacy (PsycBITE). Inter-rater reliability for the total score was excellent, both for individual raters (overall ICC = 0.84; 95% confidence interval 0.73-0.92) and for consensus ratings between pairs of raters (overall ICC = 0.88; 95% confidence interval 0.78-0.95). Item reliability was fair to excellent for consensus ratings between pairs of raters (range k = 0.48 to 1.00). The results were replicated with two independent novice raters who were trained in the use of the scale (ICC = 0.88, 95% confidence interval 0.73-0.95). The SCED Scale thus provides a brief and valid evaluation of methodological quality of single-subject designs, with the total score demonstrating excellent inter-rater reliability using both individual and consensus ratings. Items from the scale can also be used as a checklist in the design, reporting and critical

87Sr/86Sr isotope fingerprinting of Scottish and Icelandic migratory shorebirds

International Nuclear Information System (INIS)

Evans, Jane; Bullman, Rhys

2009-01-01

Biosphere Sr isotope composition data from Iceland and Scotland suggest that terrestrially feeding birds from these two countries will have significantly different 87 Sr/ 86 Sr isotope composition in their tissues. The aim of this study is to test if these differences can be measured within the bone and feather of migratory wading birds, who feed terrestrially as juveniles, thus providing a provenance tool for these birds. The study shows that birds can be distinguished on the basis of the Sr isotope composition of their bone. The field for Icelandic birds is defined by data from juvenile common redshank (Tringa totanus) and whimbrel (Numenius phaeopus) which give 0.7056 ± 0.0012, (2σ, n = 7). The majority of Scottish birds in this study are from coastal regions and have a signature close to that of seawater of 0.7095 ± 0.0006 (2σ, n = 9). The Sr ratios in the body tissue of these two populations of all Icelandic and Scottish adult and juvenile birds analysed are significantly different (p 87 Sr/ 86 Sr values as high as 0.7194 which reflect their non-marine diet. Icelandic redshank (Tringa totanus robusta) that have flown to Scotland and returned to Iceland show the effect of the Scottish contribution to their diet with elevated values of 0.7086 ± 0.0004, (2σ, n = 6). Redshank found in Scotland that cannot be classified on the basis biometric analysis are shown to be of Icelandic origin and analysis of the primary feathers from two birds demonstrates that isotope variation between feathers could be used to track changes in diet related to the timing of individual feather growth.

Synthesis and characterization of Sr2CeO4: Eu3+ phosphor by different forms

International Nuclear Information System (INIS)

Murthy, K.V.R.; Rao, Ch. Atchyutha; Suresh, K.; Ratna Kumar, B.W.; Nageswara Rao, B.; Poornachandra Rao, N.V.; Subba Rao, B.

2011-01-01

High temperature solid state reaction method was explored to synthesize undoped Sr 2 CeO 4 and Eu 3+ RE doped Sr 2 CeO 4 phosphor using inorganic materials taking in three different forms like, form (i) Strontium Carbonate (SrCO 3 ), Cerium Oxide (CeO 2 ), (ii) Strontium Nitrate (Sr(NO 3 ) 2 ), Cerium Oxide (CeO 2 ) and (iii) Strontium Nitrate (Sr(NO 3 ) 2 ), Cerium Nitrate (Ce(NO 3 ) 3 .6(NH 2 .CO.NH 2 ) in stoichiometric proportions of Sr:Ce as 2:1 and ground into a fine powder using agate mortar and pestle about an hour. The grounded samples were placed in an alumina crucible and fired at 1200 deg C for 3 hours in a muffle furnace with a heating rate of 5 deg C/min. To investigate the crystal structure, phase, morphology and luminescent properties of the synthesized phosphors XRD, SEM, Photoluminescence (PL) spectra, TL and CIE techniques were used. The Photoluminescence (PL) emission and excitation spectra were measured by Spectrofluorophotometer (SHIMADZU, RF-5301 PC) using Xenon lamp as excitation source. To identify the crystal phase, XRD analysis was carried out with a powder diffractometer (Rigaku-D/max 2500) using CuKα radiation. The microstructures of the samples were studied using a scanning electron microscopy (SEM) (XL 30 CP Philips). All the analysis was recorded at room temperature. We have compared the results of the prepared samples by different forms. From the XRD analysis it was found that the prepared phosphors are mostly in single phase of Sr 2 CeO 4 with an orthorhombic structure. From the XRD data, using Scherrer's formula the calculated average crystallite size is (i) ∼ 28 nm (ii) ∼ 9 nm (iii) ∼ 7 nm using FWHM. This indicates that, the prepared phosphors via high temperature solid state reaction method is in nano size. Sr 2 CeO 4 exhibits photoluminescence due to the charge transfer (CT) mechanism. The sample displays a broad excitation spectrum range from ∼ 220 to 400 nm. Under 350 nm excitation, the undoped Sr 2 CeO 4 shows

Interface-enhanced high-temperature superconductivity in single-unit-cell FeT e1 -xS ex films on SrTi O3

Science.gov (United States)

Li, Fangsen; Ding, Hao; Tang, Chenjia; Peng, Junping; Zhang, Qinghua; Zhang, Wenhao; Zhou, Guanyu; Zhang, Ding; Song, Can-Li; He, Ke; Ji, Shuaihua; Chen, Xi; Gu, Lin; Wang, Lili; Ma, Xu-Cun; Xue, Qi-Kun

2015-06-01

Recently discovered high-temperature superconductivity in single-unit-cell (UC) FeSe films on SrTi O3 (STO) substrate has stimulated tremendous research interest, both experimental and theoretical. Whether this scenario could be extended to other superconductors is vital in both identifying the enhanced superconductivity mechanism and further raising the critical transition temperature (Tc). Here we successfully prepared single-UC FeT e1 -xS ex(0.1 ≤x ≤0.6 ) films on STO substrates by molecular beam epitaxy and observed U -shaped superconducting gaps (Δ ) up to ˜16.5 meV , nearly ten times the gap value (Δ ˜1.7 meV ) of the optimally doped bulk FeT e0 .6S e0 .4 single crystal (Tc˜14.5 K ). No superconducting gap has been observed on the second UC and thicker FeT e1 -xS ex films at 5.7 K, indicating the important role of the interface. This interface-enhanced high-temperature superconductivity is further confirmed by ex situ transport measurements, which revealed an onset superconducting transition temperature above 40 K, nearly two times higher than that of the optimally doped bulk FeT e0 .6S e0 .4 single crystal. This work demonstrates that interface engineering is a feasible way to discover alternative superconductors with higher Tc.

Transport of Sr 2+ and SrEDTA 2- in partially-saturated and heterogeneous sediments

Science.gov (United States)

Pace, M. N.; Mayes, M. A.; Jardine, P. M.; McKay, L. D.; Yin, X. L.; Mehlhorn, T. L.; Liu, Q.; Gürleyük, H.

2007-05-01

Strontium-90 has migrated deep into the unsaturated subsurface beneath leaking storage tanks in the Waste Management Areas (WMA) at the U.S. Department of Energy's (DOE) Hanford Reservation. Faster than expected transport of contaminants in the vadose zone is typically attributed to either physical hydrologic processes such as development of preferential flow pathways, or to geochemical processes such as the formation of stable, anionic complexes with organic chelates, e.g., ethylenediaminetetraacetic acid (EDTA). The goal of this paper is to determine whether hydrological processes in the Hanford sediments can influence the geochemistry of the system and hence control transport of Sr 2+ and SrEDTA 2-. The study used batch isotherms, saturated packed column experiments, and an unsaturated transport experiment in an undisturbed core. Isotherms and repacked column experiments suggested that the SrEDTA 2- complex was unstable in the presence of Hanford sediments, resulting in dissociation and transport of Sr 2+ as a divalent cation. A decrease in sorption with increasing solid:solution ratio for Sr 2+ and SrEDTA 2- suggested mineral dissolution resulted in competition for sorption sites and the formation of stable aqueous complexes. This was confirmed by detection of MgEDTA 2-, MnEDTA 2-, PbEDTA 2-, and unidentified Sr and Ca complexes. Displacement of Sr 2+ through a partially-saturated undisturbed core resulted in less retardation and more irreversible sorption than was observed in the saturated repacked columns, and model results suggested a significant reservoir (49%) of immobile water was present during transport through the heterogeneous layered sediments. The undisturbed core was subsequently disassembled along distinct bedding planes and subjected to sequential extractions. Strontium was unequally distributed between carbonates (49%), ion exchange sites (37%), and the oxide (14%) fraction. An inverse relationship between mass wetness and Sr suggested that

Vertical migration of 85Sr, 137Cs and 131I in various arable and undisturbed soils

International Nuclear Information System (INIS)

Palagyi, S.; Palagyiova, J.

2002-01-01

Vertical migration of 85 Sr, 137 Cs and 131 I in some arable and undisturbed single-contaminated soils was studied by gamma-spectrometry measurements in lysimetric laboratory conditions applying irrigation of the soil profiles with wet atmospheric precipitation for about one year (except radioiodine). A new simple exponential compartment (box) model was derived, allowing us to calculate the migration rate constants and migration rates in the individual soil layers (vertical sections) as well as the total vertical migration rate constants and total vertical migration rates of radionuclides in the bulk soil horizon. The data from the time dependence of the depth activity distribution (radionuclide concentration along the vertical soil profile) were used to test the model. The migration rate constants and migration rates were found to be affected by the contaminating radionuclides as well as by the site, type and depth of the soil. The relaxation times of the radionuclides in the soil horizons were calculated. The effects on the rate parameters of the permanent grass cover and the zeolite applied onto the arable soil surfaces were also investigated

Inducing phase decomposition and superconductivity of Bi2Sr2CaCu2Oy single crystals treated in sulphur atmosphere at low temperature

International Nuclear Information System (INIS)

Chen, Q.W.; China Univ. of Science and Technology, Hefei, AH; Wu, W.B.; Qian, Y.T.; China Univ. of Science and Technology, Hefei, AH; Wang, L.B.; Li, F.Q.; Zhou, G.E.; Chen, Z.Y.; Zhang, Y.H.

1995-01-01

As it has been pointed out, phase decomposition which may be hard to be detected in a polycrystalline system and is likely to correlate with changes in both oxygen content and microstructure, has been observed frequently in annealed single crystals especially at higher temperatures (> 500 C). This is still an open question to some degree because the mechanism of phase decomposition is very complex and is dominated by the composition of the Bi-2212 phase, the condition of heat treatment, and the atmosphere. Hence, inducing oxygen loss at low temperature to avoid the evaporation of Bi atoms and other undetected structure changes which would occur at higher temperature annealing undoubtedly provides important information about the relationship between oxygen loss and phase decomposition, as well as the relationship between oxygen content and superconductivity. In this note, we report on the results of treatments of Bi 2 Sr 2 CaCu 2 O y single crystals in sulphur atmosphere at 160 C. (orig.)

Combined effects of Sr substitution and pressure on the ground states in CaFe2As2

Science.gov (United States)

Knöner, S.; Gati, E.; Köhler, S.; Wolf, B.; Tutsch, U.; Ran, S.; Torikachvili, M. S.; Bud'ko, S. L.; Canfield, P. C.; Lang, M.

2016-10-01

We present a detailed study of the combined effects of Sr substitution and hydrostatic pressure on the ground-state properties of CaFe2As2 . Measurements of the electrical resistance and magnetic susceptibility, both at ambient and finite pressure P ≤2 GPa, were performed on Ca1 -xSrxFe2As2 single crystals grown out of Sn flux. We find that by Sr substitution the transition temperature to the magnetic/structural phase is enhanced and therefore a higher pressure is needed to suppress the transition to lowest temperature. In addition, the transition to the collapsed tetragonal phase is found at a pressure, which is distinctly higher than in the pure compound. This implies that the stability ranges of both phases shift on the pressure-axis upon doping, but the latter one with a higher rate. These observations suggest the possibility of separating the two phase lines, which intersect already at elevated temperatures for x =0 and low Sr concentration levels. For x =0.177 , we find strong evidence that both phases remain separated down to the lowest temperature and that a zero-resistance state emerges in this intermediate pressure window. This observation indicates that Sr substitution combined with hydrostatic pressure provides another route for stabilizing superconductivity in CaFe2As2 . Our results are consistent with the notion that (i) preserving the fluctuations associated with the structural-magnetic transition to low temperatures is vital for superconductivity to form in this material and that (ii) the nonmagnetic collapsed tetragonal phase is detrimental for superconductivity.

Sr isotopes in natural waters: Applications to source characterisation and water-rock interaction in contrasting landscapes

International Nuclear Information System (INIS)

Shand, P.; Darbyshire, D.P.F.; Love, A.J.; Edmunds, W.M.

2009-01-01

Strontium isotopes ( 87 Sr/ 86 Sr) are routinely measured in hydrochemical studies to determine sources and mixing relationships. They have proved particularly useful in determining weathering processes and quantifying end-member mixing processes. A number of routine case studies are presented which highlight that Sr isotopes represent a powerful tool in the geochemists toolbox helping to constrain weathering reactions, weathering rates, flow pathways and mixing scenarios. Differences in methodologies for determining the weathering component in natural environments, inherent differences in weathering rates of different minerals, and mineral heterogeneity often cause difficulties in defining the weathering component of different catchments or aquifer systems. Nevertheless, Sr isotopes are useful when combined with other hydrochemical data, to constrain models of water-rock interaction and mixing as well as geochemical processes such as ion-exchange. This paper presents a summary of recent work by the authors in constraining the sources of waters and weathering processes in surface catchments and aquifers, and indicates cases where Sr isotopes alone are insufficient to solve hydrological problems.

Sr isotopes in natural waters: Applications to source characterisation and water-rock interaction in contrasting landscapes

Energy Technology Data Exchange (ETDEWEB)

Shand, P., E-mail: paul.shand@csiro.au [CSIRO Land and Water/CRC LEME, Private Bag 2, Glen Osmond, SA 5064 (Australia); Darbyshire, D.P.F. [NERC Isotope Geosciences Laboratory, Kingsley Dunham Centre, Keyworth, Nottingham NG12 5GG (United Kingdom); Love, A.J. [Department of Water, Land and Biodiversity Conservation, P.O. Box 2843, Adelaide 5001 (Australia); Edmunds, W.M. [School of Geography, Oxford University Centre for the Environment, South Parks Road, Oxford (United Kingdom)

2009-04-15

Strontium isotopes ({sup 87}Sr/{sup 86}Sr) are routinely measured in hydrochemical studies to determine sources and mixing relationships. They have proved particularly useful in determining weathering processes and quantifying end-member mixing processes. A number of routine case studies are presented which highlight that Sr isotopes represent a powerful tool in the geochemists toolbox helping to constrain weathering reactions, weathering rates, flow pathways and mixing scenarios. Differences in methodologies for determining the weathering component in natural environments, inherent differences in weathering rates of different minerals, and mineral heterogeneity often cause difficulties in defining the weathering component of different catchments or aquifer systems. Nevertheless, Sr isotopes are useful when combined with other hydrochemical data, to constrain models of water-rock interaction and mixing as well as geochemical processes such as ion-exchange. This paper presents a summary of recent work by the authors in constraining the sources of waters and weathering processes in surface catchments and aquifers, and indicates cases where Sr isotopes alone are insufficient to solve hydrological problems.

Optimizing magnetic anisotropy of La{sub 1−x}Sr{sub x}MnO{sub 3} nanoparticles for hyperthermia applications

Energy Technology Data Exchange (ETDEWEB)

Rashid, Amin ur [Magnetism Laboratory, Department of Physics, COMSATS Institute of Information Technology, Islamabad (Pakistan); Department of Applied Physical and Material Sciences, University of Swat, Khyber Pakhtunkhwa (Pakistan); Manzoor, Sadia, E-mail: sadia_manzoor@comsats.edu.pk [Magnetism Laboratory, Department of Physics, COMSATS Institute of Information Technology, Islamabad (Pakistan)

2016-12-15

Maximizing the magnetothermal response of magnetic nanoparticles (MNP's) for hyperthermia applications is a complex problem, because it depends sensitively upon interrelated magnetic and structural parameters. The task is somewhat simpler for systems with fixed composition, e.g. Fe{sub 3}O{sub 4} or CoFe{sub 2}O{sub 4}, in which the particle size is the only means of modifying the magnetic anisotropy, and hence the magnetothermal response. In the La{sub 1−x}Sr{sub x}MnO{sub 3} system however, the magnetic interactions as well as the particle size both change with the Sr concentration x, which makes it a much more complex system for which to optimize the hyperthermia response. We have investigated the effect of magnetic anisotropy on the magnetothermal response of La{sub 1−x}Sr{sub x}MnO{sub 3} nanoparticles as a function of the particle size as well as the Sr concentration x where 0.20≤x≤0.45. The optimum particle size range is 25–30 nm for all concentrations, where the specific absorption rate (SAR) has a maximum. The linear response theory (LRT) has been applied to this system and good agreement has been found between the experimental and theoretically determined values of the SAR for samples lying in the single domain regime and having large enough anisotropy energies. The agreement is much better for the intermediate concentrations of 0.27 and 0.33, because of their large anisotropy as compared to other concentrations. It is concluded that the LRT can be successfully used to predict the SAR of these nanoparticles, provided they possess large enough effective anisotropies. Values of the ILP have been obtained for these samples and found to be comparable to those of magnetite and some commercial ferrofluids. - Highlights: • For La{sub 1-x}Sr{sub x}MnO{sub 3} system, the magnetic anisotropy is determined not only by the particle size, but also by the strontium content x, we made a systematic study of both these parameters on its magnetothermal

Sol-Gel Synthesis of La(0.6)Sr(0.4)CoO(3-x) and Sm(0.5)Sr(0.5)CoO(3-x) Cathode Nanopowders for Solid Oxide Fuel Cells

Science.gov (United States)

Bansal, Narottam P.; Wise, Brent

2011-01-01

Nanopowders of La(0.6)Sr(0.4)CoO(3-x) (LSC) and Sm(0.5)Sr(0.5)CoO(3-x) (SSC) compositions, which are being investigated as cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFC) with La(Sr)Ga(Mg)O(3-x) (LSGM) as the electrolyte, were synthesized by low-temperature sol-gel method using metal nitrates and citric acid. Thermal decomposition of the citrate gels was followed by simultaneous DSC/TGA methods. Development of phases in the gels, on heat treatments at various temperatures, was monitored by x-ray diffraction. Solgel powders calcined at 550 to 1000 C consisted of a number of phases. Single perovskite phase La(0.6)Sr(0.4)CoO(3-x) or Sm(0.5)Sr(0.5)CoO(3-x) powders were obtained at 1200 and 1300 C, respectively. Morphological analysis of the powders calcined at various temperatures was done by scanning electron microscopy. The average particle size of the powders was approx.15 nm after 700 C calcinations and slowly increased to 70 to 100 nm after heat treatments at 1300 to 1400 C.

A compact SR light source for x-ray lithography 'AURORA'

International Nuclear Information System (INIS)

Toba, Y.

1990-01-01

A compact synchrotron radiation (SR) light source called AURORA has been developed for industrial use. It is specially designed for X-ray lithography. AURORA consists of a storage ring, injector microtron and SR light beam lines. The storage ring is a superconducting single magnet machine, designed to accelerate a 150 MeV electron beam to 650 MeV and to store as high as 300 mA current. The injector is a racetrack microtron (RTM) producing a pulsed 150 MeV beam. As many as 16 SR light beam channels are available for AURORA. Prototypes of the storage ring and RTM are constructed, and beam commissioning is performed. A hundred and fifty MeV electron beam of a pulsed current 10 μA from the RTM is successfully injected to the ring and accelerated to 600 MeV and 10 mA current stored with a lifetime of more than 20 hours. The half-integer method investigated is shown to work well with the injection efficiency being found to be very high. Improvement of the design is now under way. (N.K.)

Synthesis, single-crystal structure determination and Raman spectrum of Ca{sub 2.57(4)}Sr{sub 0.43(4)}Cl{sub 2}[CBN

Energy Technology Data Exchange (ETDEWEB)

Reckeweg, Olaf; DiSalvo, Francis J. [Cornell Univ., Ithaca, NY (United States). Dept. of Chemistry and Chemical Biology; Schulz, Armin [Max-Planck-Institut fuer Festkoerperforschung, Stuttgart (Germany)

2017-05-01

Solid-state reaction of Ca, CaCl{sub 2}, Sr, SrCl{sub 2}, C and BN at 900 C for 3 days yielded transparent red needles of Ca{sub 2.57(4)}Sr{sub 0.43(4)}Cl{sub 2}[CBN] as minority product (<10%) mixed with crystals of isotypic yellow Ca{sub 3}Cl{sub 2}[CBN] and orange Sr{sub 3}Cl{sub 2}[CBN]. Ca{sub 2.57(4)}Sr{sub 0.43(4)}Cl{sub 2}[CBN] crystallizes in the space group Pnma (no.62) with the unit cell parameters of a=1389.2(6), b=386.05(15) and c=1131.2(4)pm (Z=4). The Raman spectrum confirms the presence of the [CBN]{sup 4-} unit. The incremental volume of the [CBN]{sup 4-} is calculated to be 50.7(10) Aa{sup 3}.

EPR of photochromic Mo3+ in SrTiO3

NARCIS (Netherlands)

Kool, Th.W.

2010-01-01

In single crystals of SrTiO_3, a paramagnetic center, characterized by S = 3/2 and hyperfine interaction with an I = 5/2 nuclear spin has been observed in the temperature range 4.2K-77K by means of EPR. The impurity center is attributed to Mo3+. No additional line splitting in the EPR spectrum due

Native SrTiO3 (001) surface layer from resonant Ti L2,3 reflectance spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Valvidares, Manuel; Huijben, Mark; Yu, Pu; Ramesh, Ramamoorthy; Kortright, Jeffrey

2010-11-03

We quantitatively model resonant Ti L2,3 reflectivity Rs,p(q, hn) from several SrTiO3 (001) single crystals having different initial surface preparations and stored in ambient conditions before and between measurements. All samples exhibit unexpected 300 K Rs(hn) - Rp(hn) anisotropy corresponding to weak linear dichroism and tetragonal distortion of the TiO6 octahedra indicating a surface layer with properties different from cubic SrTiO3. Oscillations in Rs(q) confirm a ubiquitous surface layer 2-3 nm thick that evolves over a range of time scales. Resonant optical constant spectra derived from Rs,p(hn) assuming a uniform sample are refined using a single surface layer to fit measured Rs(q). Differences in surface layer and bulk optical properties indicate that the surface is significantly depleted in Sr and enriched in Ti and O. While consistent with the tendency of SrTiO3 surfaces toward non-stoichiometry, this layer does not conform simply to existing models for the near surface region and apparently forms via room temperature surface reactions with the ambient. This new quantitative spectral modeling approach is generally applicable and has potential to study near-surface properties of a variety of systems with unique chemical and electronic sensitivities.

Evidence for monoclinic distortion in the ground state phase of underdoped La_1_._9_5Sr_0_._0_5CuO_4: A single crystal neutron diffraction study

International Nuclear Information System (INIS)

Singh, Anar; Schefer, Jürg; Frontzek, Matthias; Sura, Ravi; Conder, Kazimierz; Sibille, Romain F.; Ceretti, Monica; Paulus, Werner

2016-01-01

The existing controversy about the symmetry of the crystal structure of the ground state of the critical doped La_1_._9_5Sr_0_._0_5CuO_4 has been resolved by analyzing the single crystal neutron diffraction data collected between 5 and 730 K. We observed small but significant intensities for “forbidden” reflections given by extinction rules of the orthorhombic Bmab space group at low temperatures. A careful investigation of neutron diffraction data reveals that the crystal structure of La_1_._9_5Sr_0_._0_5CuO_4 at 5 K is monoclinic with B2/m (2/m 1 1) space group. The monoclinic structure emerges from the orthorhombic structure in a continuous way; however, the structure is stable below ∼120 K which agrees with other observed phenomena. Our results on symmetry changes are crucial for the interpretation of physical properties also in other high temperature superconductors with similar structures.

Stress-relaxation tests in the work-hardening regime of tungsten single crystals below 300 K

International Nuclear Information System (INIS)

Brunner, D.

2008-01-01

The influence of work hardening on the results of stress-relaxation tests was studied for highly pure tungsten single crystals isothermally deformed at four temperatures of 274, 241, 131, and 78 K. A method accounting for strong work hardening on the determination of the strain-rate sensitivity from stress-relaxation tests is introduced by establishing special diagrams of SR tests denoted as YX diagrams

Low-temperature specific heat of single-crystal Bi2CaSr2Cu2O8 and Tl2Ca2Ba2Cu3O10

Science.gov (United States)

Urbach, J. S.; Mitzi, D. B.; Kapitulnik, A.; Wei, J. Y. T.; Morris, D. E.

1989-06-01

We report specific-heat measurements from 2 to 15 K on single crystals of Bi2CaSr2Cu2O8 and Tl2Ca2Ba2Cu3O10 We find low-temperature deviations from the Debye law that can be attributed to spin-glass behavior of a small concentration of isolated impurity copper moments. At higher temperatures, we observe contributions to the specific heat that can be attributed to a soft-phonon mode, possibly associated with the superstructure in the Bi-O and Tl-O layers. From our single-crystal data, we conclude that the thallium- and bismuth-based copper oxide superconductors show no measurable linear term in the specific heat [γ(0)<=1 mJ/mole K2].

Temperature dependence of the dispersion of single crystals SrCl/sub 2/. [Temperature coefficient

Energy Technology Data Exchange (ETDEWEB)

Kuzin, M P [L' vovskij Gosudarstvennyj Univ. (Ukrainian SSR)

1976-01-01

The dispersion of the refractive index of SrCl/sub 2/ monocrystals in the spectral range 300-700 nm at temperatures of 223, 295 adn 373 K has been studied. The temperature coefficient of the refractive index as a function of the wave length has been determined for the room temperature. The function resembles the corresponding dependence for alkali-halide crystals.

Identification of Marchfeld asparagus using Sr isotope ratio measurements by MC-ICP-MS

Energy Technology Data Exchange (ETDEWEB)

Swoboda, S; Brunner, M; Boulyga, S F; Galler, P; Prohaska, T [University of Natural Resources and Applied Life Sciences, Department of Chemistry-VIRIS Project, Vienna (Austria); Horacek, M [Austrian Research Centers GmbH, Seibersdorf (Austria)

2008-01-15

This work focuses on testing and application of Sr isotope signatures for the fast and reliable authentication and traceability of Asparagus officinalis originating from Marchfeld, Austria, using multicollector inductively coupled plasma mass spectrometry after optimised Rb/Sr separation. The major sample pool comprises freeze-dried and microwave-digested asparagus samples from Hungary and Slovakia which are compared with Austrian asparagus originating from the Marchfeld region, which is a protected geographical indication. Additional samples from Peru, the Netherlands and Germany were limited in number and allowed therefore only restricted statistical evaluation. Asparagus samples from Marchfeld were harvested within two subsequent years in order to investigate the annual variation. The results show that the Sr isotope ratio is consistent within these 2 years of investigation. Moreover, the Sr isotope ratio of total Sr in soil was found to be significantly higher than in an NH{sub 4}NO{sub 3} extract, reflecting the mobile (bioavailable) phase. The isotope composition in the latter extract corresponds well to the range found in the asparagus samples in Marchfeld, even though the concentration of Sr in asparagus shows no direct correlation to the concentration of Sr in the mobile phase of the soil. The major question was whether the 'Marchfelder Spargel' can be distinguished from samples from the neighbouring countries of Hungary and Slovakia. According to our findings, they can be clearly (100%) singled out from the Hungarian samples and can be distinguished from the Slovakian asparagus samples with a probability of more than 80%. (orig.)

Identification of Marchfeld asparagus using Sr isotope ratio measurements by MC-ICP-MS

Energy Technology Data Exchange (ETDEWEB)

Swoboda, S.; Brunner, M.; Boulyga, S.F.; Galler, P.; Prohaska, T. [University of Natural Resources and Applied Life Sciences, Department of Chemistry-VIRIS Project, Vienna (Austria); Horacek, M. [Austrian Research Centers GmbH, Seibersdorf (Austria)

2008-01-15

This work focuses on testing and application of Sr isotope signatures for the fast and reliable authentication and traceability of Asparagus officinalis originating from Marchfeld, Austria, using multicollector inductively coupled plasma mass spectrometry after optimised Rb/Sr separation. The major sample pool comprises freeze-dried and microwave-digested asparagus samples from Hungary and Slovakia which are compared with Austrian asparagus originating from the Marchfeld region, which is a protected geographical indication. Additional samples from Peru, the Netherlands and Germany were limited in number and allowed therefore only restricted statistical evaluation. Asparagus samples from Marchfeld were harvested within two subsequent years in order to investigate the annual variation. The results show that the Sr isotope ratio is consistent within these 2 years of investigation. Moreover, the Sr isotope ratio of total Sr in soil was found to be significantly higher than in an NH{sub 4}NO{sub 3} extract, reflecting the mobile (bioavailable) phase. The isotope composition in the latter extract corresponds well to the range found in the asparagus samples in Marchfeld, even though the concentration of Sr in asparagus shows no direct correlation to the concentration of Sr in the mobile phase of the soil. The major question was whether the 'Marchfelder Spargel' can be distinguished from samples from the neighbouring countries of Hungary and Slovakia. According to our findings, they can be clearly (100%) singled out from the Hungarian samples and can be distinguished from the Slovakian asparagus samples with a probability of more than 80%. (orig.)

Phase 0 Clinical Chemoprevention Trial of the AKT Inhibitor SR13668

Science.gov (United States)

Reid, Joel M.; Walden, Chad; Qin, Rui; Allen Ziegler, Katie L.; Haslam, John L.; Rajewski, Roger A.; Warndahl, Roger; Fitting, Cindy L.; Boring, Daniel; Szabo, Eva; Crowell, James; Perloff, Marjorie; Jong, Ling; Mandrekar, Sumithra J.; Ames, Matthew M.; Limburg, Paul J.

2011-01-01

Purpose SR13668, an orally active AKT pathway inhibitor, has demonstrated cancer chemopreventive potential in preclinical studies. To accelerate the clinical development of this promising agent, we designed and conducted the first-ever phase 0 chemoprevention trial to evaluate and compare the effects of food and formulation on SR13668 bioavailability. Patients and Methods Healthy adult volunteers were randomly assigned to receive a single, 38 mg oral dose of SR13668 in one of five different formulations, with or without food. Based on existing animal data, SR13668 in a PEG400/Labrasol® oral solution was defined as the reference formulation. Blood samples were obtained pre- and post-agent administration for pharmacokinetic analyses. Area under the plasma concentration-time curve (AUC0-∞) was defined as the primary endpoint. Data were analyzed and compared using established statistical methods for phase 0 trials with a limited sample size. Results Participants (N=20) were rapidly accrued over a 5-month period. Complete pharmacokinetic data were available for 18 randomized participants. AUC0-∞ values were highest in the fed state (range = 122–439 ng/mL × hours) and were statistically significantly different across formulations (p = 0.007), with Solutol® HS15 providing the highest bioavailability. SR13668 time to peak plasma concentration (3 hours; range, 2 – 6 hours) and half-life were (11.2 ± 3.1 hours) were not formulation dependent. Conclusions Using a novel, highly efficient study design, we rapidly identified a lead formulation of SR13668 for further clinical testing. Our findings support application of the phase 0 trial paradigm to accelerate chemoprevention agent development. PMID:21372034

Lattice site location and annealing behaviour of Ca and Sr implanted GaN

CERN Document Server

De Vries, Bart; Wahl, Ulrich; Correia, J G; Araújo, João Pedro; Lojkowski, W; Kolesnikov, D

2006-01-01

We report on the lattice location of ion-implanted Ca and Sr in thin films of single-crystalline wurtzite GaN. Using the emission channeling technique the angular distributions of $\\beta\\!^{-}$−particles emitted by the radioactive isotopes $^{45}$Ca(t$_{ 1/2}$=163.8 d) and $^{89}$Sr(t$_{ 1/2}$=50.53 d) were monitored with a position-sensitive detector following 60 keV room-temperature implantation. Our experiments give direct evidence that $\\sim$90% of Ca and > 60% of Sr atoms were occupying substitutional Ga sites with root mean square displacements of the order of 0.15–0.30 Å, i.e., larger than the expected thermal vibration amplitude of 0.074 Å. Annealing the Ca implanted samples at 1100–1350 °C in high-pressure N$_{2}$ atmosphere resulted in a better incorporation into the substitutional Ga site. The Sr implanted sample showed a small decrease in rms displacements for vacuum annealing up to 900 °C, while the substitutional fraction remained nearly constant. The annealing behavior of the rms disp...

Single-crystalline Bi2Sr2CaCu2O8+x detectors for direct detection of microwave radiation

International Nuclear Information System (INIS)

Li, M.; Winkler, D.; Yurgens, A.

2015-01-01

We test radiation detectors made from single-crystalline Bi 2 Sr 2 CaCu 2 O 8+x flakes put on oxidized Si substrates. The 100-nm-thick flakes are lithographically patterned into 4×12 μm 2 large rectangles embedded in thin-film log-spiral antennas. The SiO 2 layer weakens the thermal link between the flakes and the bath. Two modes of radiation detection have been observed. For a bolometric type of sensors a responsivity of ∼300 V/W and a noise equivalent power of 30 nW/√(Hz) has been deduced at 70 K. Much more sensitive is the non-bolometric device showing characteristics similar to a Golay-type detector while being at least a thousand times faster. Making smaller (sub-μm) structures is expected to significantly improve the performance of these devices and makes them very competitive among other microwave and terahertz detectors

Thermodynamic assessment of the Pb-Sr system

Directory of Open Access Journals (Sweden)

Zhang H.

2017-01-01

Full Text Available The Pb-Sr system has been critically reviewed and modeled by means of the CALPHAD (CALculation of PHAse Diagrams approach. It contains seven stoichiometric compounds, i.e. SrPb3, Sr3Pb5, Sr2Pb3, SrPb, Sr5Pb4, Sr5Pb3 and Sr2Pb, in which the SrPb3 and Sr2Pb phases melt congruently, and the other five phases form via peritectic reactions. The enthalpies of formation for the intermetallic compounds at 0 K are provided by first-principles calculations. The liquid, fcc and bcc phases are modeled as substitutional solution phases. Both Redlich-Kister and exponential polynomials are used to describe the excess Gibbs energy of the liquid. Two sets of self-consistent thermodynamic parameters are obtained by considering reliable experimental data and the computed enthalpies of formation. Comprehensive comparisons between the calculated and measured phase diagram and thermodynamic data show that the experimental information is satisfactorily accounted for by the present thermodynamic description.

System of Sr(NO2)2-Sr(OH)2-H2O at 25 deg C

International Nuclear Information System (INIS)

Popova, T.B.; Berdyukova, V.A.; Khutsistova, F.M.

1990-01-01

Sr(NO 2 ) 2 -Sr(OH) 2 -H 2 O system was investigated by the methods of solubility, density, viscosity, electric conductivity and refractometry. It was established that its compoments form the compound 4Sr(NO 2 ) 2 xSr(OH) 2 x8H 2 O. The compound was separated from solution; its density, decomposition temperature were determined; IR spectra and X-ray patterns of prepared and initial compounds were obtained

C, Sr and Sr isotopic composition on probable vendian- tommotian carbonate sequences in Nw Argentina

International Nuclear Information System (INIS)

Sial, A. N.; Ferreira, V.P; Toselli, A.J.; Acenolaza, F.G; Pimentel, M.M; Parada, M.A; Alonso, R.N

2001-01-01

C-isotope stratigraphy is one of the most powerfool tools in Precambrian chronostratigraphy, especially when sediments lack recognizable animal fossils. The δ 13 C secular variation curves for marine carbonates in the Neoproterozoic-Cambrian interval show strong positive-negative excursions, several of them interpreted as the stratigraphic position of ancient ice ages (Hoffman et al. 1998). The Sr isotope composition of the seawater for this age interval is characterized by a continuous increase of 87 Sr/ 86 Sr that is interrupted, several times, by sharp rises, which represent important changes in the Earth history (Montanez et al. 2000). Only limited data on the behavior of C and Sr isotopes in carbonates are available in South America. We examine here carbonate sequences from the Argentine Precordillera, San Juan province, and from other carbonate sequences in NW Argentina that could be, potentially, proxies for the Precambrian-Cambrian transition. We have studied their δ 13 C and 87 Sr/ 86 Sr chemostratigraphy and compare it to global C and Sr isotope secular variation curves for this time span. This study aims to improve the relatively coarse stratigraphic resolution provided only by the study of the fossil record in some of the carbonate successions under consideration (au)

Influence of the sintering temperature on the Sr content in a Ca_(_1_−_x_−_y_)Ce_xSr_yAl_zTi_(_1_−_z_)O_3 perovskite (x = 0.04–0.16) co-doped with Ce

International Nuclear Information System (INIS)

Kamel, Nour-el-hayet; Mouheb, Yasmina; Kamel, Ziane; Moudir, Dalila; Aouchiche, Fairouz; Arabi, Azeddine

2016-01-01

A Sr-Ce co-doped perovskite, with the chemical formula: Ca_(_1_−_x_−_y_)Ce_xSr_yAl_zTi_(_1_−_z_)O_3 (y = 0.04, 0.08, 0.12 and 0.16, x = 0.05) is synthesized by sol–gel process. The influence of the sintering temperature, Ts, on the rate of inserted Sr was investigated at 1223, 1373 and 1473 K. The Sr amount sequestered in the perovskite reaches 85% (y = 0.16, 9.50 wt%) for Ts = 1373 K, giving sintering densities between 3.520 and 4.400. XRD analysis reveals an orthorhombic CaTiO_3 structure. The lattice parameters obey to Vegard’s law for Ts = 1373 and 1473 K. SEM analysis shows orthorhombic grains of 0.514 μm × 1 μm mean dimensions. MCC1 and MCC2 tests, performed on minerals sintered at 1373 K, indicate that the most durable one is that containing 9.50 wt% Sr. MCC1 test gave 6.998·10"−"6 g/cm"2 d of Sr, and MCC2 2.143·10"−"4 g/cm"2 d of Ce. The temperature favors the Sr dissolution to the detriment of Ce. The Ca dissolution rate reaches 1.002·10"−"6 to 2.005·10"−"6 g/cm"2 d. - Highlights: • Ca_(_1_−_x_−_y_)Ce_xSr_yAl_zTi_(_1_−_z_)O_3 perovskite is synthesized by sol–gel. • The influence of the sintering temperature, Ts, on the rate of inserted Sr was investigated at 1223, 1373 and 1473 K. • 85% of total Sr was sequestered in the perovskite for Ts = 1373 K. • MCC1 and MCC2 leach tests indicate that the most durable mineral is that containing 9.50 wt.% Sr. • MCC1 test gave 8.10 10"−"1"0 kg/m"2.d Sr. The lower is the leaching temperature the higher is the mineral durability.

Extraction and Analysis of Strontium in Water Sample Using a Sr2+ Selective Polymer as the Absorbent Phase

Directory of Open Access Journals (Sweden)

Rongjian Ying

2015-01-01

Full Text Available A kind of Sr2+ selective resin was applied as an absorption phase to extract Sr2+ ion from an aqueous solution, and the amount of Sr2+ was determined using inductively coupled plasma optical emission spectrometer. Factors, including absorption time, temperature, stirring rate, salt-out effect, desorption, and the pH of the aqueous solution, were investigated to optimize the absorption efficiency of Sr2+. Foreign ions were examined to observe their effects on the absorption behavior of Sr2+. The optimum condition was absorption time at 20 min, pH of aqueous solution 7, temperature of 35°C, and 600 rpm stirring rate. A 10 mL solution of 0.1 mol/L HCl is used as the desorption agent. The linear range of Sr2+ concentrations from 50 to 1200 μg/L was investigated with the slope of 183 μg/L. The limit of detection was 21 μg/L with 4.23% relative standard deviation. The correlation coefficient was found to be 0.9947. Under the optimized conditions, the concentrations of Sr2+ in four water samples were detected by the developed method. We propose that this method effectively extracts strontium ion from environmental water samples.

Measurement of resonance integral of the 90Sr(n,γ)91Sr reaction

International Nuclear Information System (INIS)

Nakamura, Shoji; Furutaka, Kazuyoshi; Wada, Hiroaki; Katoh, Toshio; Harada, Hideo; Fujii, Toshiyuki; Yamana, Hajimu

2001-01-01

To obtain fundamental data for research on nuclear transmutation method of radioactive wastes, the resonance integral (I 0 ) of the 90 Sr(n,γ) 91 Sr reaction was measured with an activation method. (author)

Inhomogeneous electronic structures in heavily Pb-doped Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub y} single crystals probed by low temperature STM/STS

Energy Technology Data Exchange (ETDEWEB)

Kinoda, Go; Nakao, Shoichiro; Motohashi, Teruki; Nakayama, Yuri; Shimizu, Keisuke; Shimoyama, Junichi; Kishio, Koji; Hanaguri, Tetsuo; Kitazawa, Koichi; Hasegawa, Tetsuya

2003-05-15

We have performed cryogenic scanning tunneling microscopy/spectroscopy (STM/STS) of heavily Pb-doped Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub y} single crystals to investigate local electronic structures in the overdoped regime. The obtained STM/STS results at 4.3 K clearly showed local inhomogeneity of gap structure {delta} ({delta}=20-60 meV) in a scale of several nm, suggesting the coexistence of superconducting and pseudogap-like regions, even in the overdoped regime.

The effect of diameter ratio between transducers and reactor in sonication-assisted synthesis of Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Manaf, A., E-mail: azwar@ui.ac.id; Fahmi, Agam Aidil [Department of Physics, FMIPA, Universitas Indonesia, Kampus UI Depok (Indonesia); Yustanti, Erlina [Department of Physics, FMIPA, Universitas Indonesia, Kampus UI Depok (Indonesia); Department of Metallurgy, Faculty of Engineering, University of Sultan AgengTirtayasa Jl. Jenderal Sudirman KM 03 Cilegon-Banten 65134 (Indonesia)

2016-04-19

This paper describes the particle size characterization of mechanically alloyed Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3} prepared with the aid of a high-power ultrasonic destruction. Analytical-grade BaCO{sub 3}, TiO{sub 2} and SrCO{sub 3} with a purity greater than 99 wt.% were used as precursors for Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3}. The mechanically powders were respectively sintered at 1200 °C for 3 hours to form crystalline powders. This work is aimed at studying the effect of diameter ratio between reactor and transducer of a high power sonicator on the Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3} nanoparticles formation. The presence of a single phase of the two materials was confirmed by X-Ray Diffraction (XRD). The concentration of the particles in demineralized water was 3.0 g / 100 mL which become the object of 3 hours ultrasonic destruction subjected to the application of transducer in which the ratio between the diameter of the reactor and the transducer (D/d) was fixed at 1.4, 1.6 and 1.8 respectively. It was found that the mean particle size before the ultrasonic destruction was 538 nm for Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and 480 nm for Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3}. With D/d of 1.8, the mean particle size of the two materials was found to decrease drastically to 38 nm and 24 nm, respectively. These mean particle sizes were respectively comparable with that of the crystallite size of the particles derived using the Whole Powder Pattern Modelling (WPPM) from which the mean crystallite size of 22 nm for Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and 14 nm for Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3} were obtained. It is then confirmed single nanocrystallite Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} and Ba{sub 0.3}Sr{sub 0.7}TiO{sub 3} particles were already achieved. We can conclude that the ultrasonic destruction to mechanically milled crystalline particles would be one

Improved oral bioavailability in rats of SR13668, a novel anti-cancer agent.

Science.gov (United States)

Green, Carol E; Swezey, Robert; Bakke, James; Shinn, Walter; Furimsky, Anna; Bejugam, Naveen; Shankar, Gita N; Jong, Ling; Kapetanovic, Izet M

2011-05-01

SR13668, a bis-indole with potent activity in vitro and in vivo against various cancers and promising cancer chemopreventive activity, was found to have very low oral bioavailability, <1%, in rats during pilot pharmacokinetic studies. The objective of these studies was to better understand the source of low oral exposure and to develop a formulation that could be used in preclinical development studies. An automated screening system for determining solubility in lipid-based vehicles, singly and in combination, was used to identify formulations that might enhance absorption by improving solubility of SR13668, and these results were confirmed in vivo using Sprague-Dawley rats. Pharmacokinetics of SR13668 was then determined in male and female Sprague-Dawley rats administered 1 mg/kg iv, 1, 10, and 30 mg/kg po formulated in PEG400:Labrasol (1:1 v/v). Blood was collected at time points through 24 h and the concentration of SR13668 determined using HPLC with UV and fluorescence detection. SR13668 was found to be resistant to plasma esterases in vitro and relatively stable to rat and human liver microsomal metabolism. SR13668 concentrates in tissues as indicated by significantly higher levels in lung compared to blood, blood concentrations ~2.5-fold higher than plasma levels, and apparent volume of distribution (V) of ~5 l/kg. A marked sex difference was observed in exposure to SR13668 with area under the curve (AUC) significantly higher and clearance (CL) lower for female compared to male rats, after both iv and oral administration. The oral bioavailability (F) of SR13668 was 25.4 ± 3.8 and 27.7 ± 3.9% (30 mg/kg), for males and females, respectively. A putative metabolite (M1), molecular weight of 445 in the negative ion mode (i.e., SR13668 + 16), was identified in blood samples from both the iv and po routes, as well as in vitro microsomal samples. In summary, while SR13668 does undergo metabolism, probably by the liver, the oral bioavailability of SR13668 in rats

FEP report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

2010-12-15

This report documents the analysis and processing of features, events and processes, FEPs, that has been carried out within the safety assessment SR-Site, and forms an important part of the reporting of the project. The main part of the work was conducted within the earlier safety assessment SR-Can, which was a preparatory stage for the SR-Site assessment. The overall objective of the FEP analysis and processing in both SR-Can and SR-Site included development of a database of features, events and processes, an SKB FEP database, in a format that facilitates both a systematic analysis of FEPs and documentation of that FEP analysis, as well as facilitating revisions and updates to be made in connection with new safety assessments. The primary objective in SR-Site was to establish an SR-Site FEP catalogue within the framework of the SKB FEP database. This FEP catalogue was required to contain all FEPs that needed to be handled in SR-Site and is an update of the corresponding SR-Can FEP catalogue that was established for the SR-Can assessment. The starting point for the handling of FEPs in SR-Site was the SR-Can version of the SKB FEP database and associated SR-Can reports. The SR-Can version of the SKB FEP database includes the SR-Can FEP catalogue, as well as the sources for the identification of FEPs in SR-Can, namely the SR 97 processes and variables, Project FEPs in the NEA International FEP database version 1.2 and matrix interactions in the Interaction matrices developed for a deep repository of the KBS-3 type. Since the completion of the FEP work within SR-Can, an updated electronic version, version 2.1, of the NEA FEP database has become available. Compared with version 1.2 of the NEA FEP database, version 2.1 contains FEPs from two more projects. As part of SR-Site, all new Project FEPs in version 2.1 of the NEA FEP database have been mapped according to the methodology adopted in SR-Can resulting in an SR-Site version of the SKB FEP database. The SKB FEP

FEP report for the safety assessment SR-Site

International Nuclear Information System (INIS)

2010-12-01

This report documents the analysis and processing of features, events and processes, FEPs, that has been carried out within the safety assessment SR-Site, and forms an important part of the reporting of the project. The main part of the work was conducted within the earlier safety assessment SR-Can, which was a preparatory stage for the SR-Site assessment. The overall objective of the FEP analysis and processing in both SR-Can and SR-Site included development of a database of features, events and processes, an SKB FEP database, in a format that facilitates both a systematic analysis of FEPs and documentation of that FEP analysis, as well as facilitating revisions and updates to be made in connection with new safety assessments. The primary objective in SR-Site was to establish an SR-Site FEP catalogue within the framework of the SKB FEP database. This FEP catalogue was required to contain all FEPs that needed to be handled in SR-Site and is an update of the corresponding SR-Can FEP catalogue that was established for the SR-Can assessment. The starting point for the handling of FEPs in SR-Site was the SR-Can version of the SKB FEP database and associated SR-Can reports. The SR-Can version of the SKB FEP database includes the SR-Can FEP catalogue, as well as the sources for the identification of FEPs in SR-Can, namely the SR 97 processes and variables, Project FEPs in the NEA International FEP database version 1.2 and matrix interactions in the Interaction matrices developed for a deep repository of the KBS-3 type. Since the completion of the FEP work within SR-Can, an updated electronic version, version 2.1, of the NEA FEP database has become available. Compared with version 1.2 of the NEA FEP database, version 2.1 contains FEPs from two more projects. As part of SR-Site, all new Project FEPs in version 2.1 of the NEA FEP database have been mapped according to the methodology adopted in SR-Can resulting in an SR-Site version of the SKB FEP database. The SKB FEP

Thermal infrared and microwave absorbing properties of SrTiO3/SrFe12O19/polyaniline nanocomposites

International Nuclear Information System (INIS)

Hosseini, Seyed Hossein; Zamani, Parisa; Mousavi, S.Y.

2015-01-01

Graphical abstract: We have developed a new perspective of applications and properties of conducting polymers. The combination of absorption ability prepared nanocomposites in the present of PANI display a great potential in organization of shielding structures into thermal IR and microwave. Further investigations using other conducting polymers to demonstrate their capability for advance thermal IR and microwave shielding devices is under way. The application of these samples may improve the IR thermographic detection, catalysis, sensors, magnetic data storage, electromagnetic resonance wave absorption, photonic crystals, and microelectronic devices and military aspects. - Highlights: • The SrTiO 3 /SrFe 12 O 19 /PANI exhibited electric and electromagnetic properties. • The SrTiO 3 /SrFe 12 O 19 /PANI has shielding structures into thermal IR and microwave. • Increasing weight ratios and thicknesses will increase thermal IR ability. • Increasing weight ratios and thicknesses will increase microwave absorption ability. - Abstract: Polyaniline (PANI) as a unique polymer that also has electromagnetic absorption used as the substrate. In this research, SrTiO 3 was synthesized as IR absorbent and core and then SrFe 12 O 19 as microwave absorbent was prepared on SrTiO 3 via co-precipitation method as the first shell. As the next step, PANI was coated on SrTiO 3 /SrFe 12 O 19 nanoparticles via in situ polymerization by multi core–shell structures (SrTiO 3 /SrFe 12 O 19 /PANI). Nanometer size and structures of samples were measured by TEM, XRD and FTIR. Morphology of nanocomposite was showed by SEM images. The magnetic and electric properties were also performed by VSM and four probe techniques. Thermal infrared (IR) absorption and microwave reflection loss of nanocomposites were investigated at 10–40 μm and 8–12 GHz, IR and microwave frequencies, respectively. The results showed that the SrTiO 3 /SrFe 12 O 19 /PANI nanocomposites have good compatible

Evaluation of thermodynamic and kinetic stability of P-type transparent conducting oxide, SrCu2O2 under various oxygen partial pressures

International Nuclear Information System (INIS)

Sugimoto, Takayuki; Yanagawa, Atsumi; Hashimoto, Takuya

2012-01-01

Highlights: ▶ Thermodynamic and kinetic stabilities of SrCu 2 O 2 under various P(O 2 ) was estimated. ▶ The reaction rate for decomposition decreased with decreasing temperature and P(O 2 ). ▶ The activation energy for decomposition of SrCu 2 O 2 was estimated to be 66 kJ/mol. ▶ SrCu 2 O 2 showed less stability than those of other transparent p-type semiconductors. - Abstract: Kinetic stability of transparent p-type conducting oxide, SrCu 2 O 2 , has been evaluated by using X-ray diffraction measurement and thermogravimetry. It was revealed that SrCu 2 O 2 decomposed to mixture of CuO and Sr 14 Cu 24 O 41 in air at temperatures above 300 °C. The decomposition reaction rate can be successfully explained by kinetic model assuming first-order chemical reaction. The rate constant can be suppressed with decreasing temperature and oxygen partial pressure. The activation energy for decomposition reaction of SrCu 2 O 2 calculated from Arrhenius plot was 66 kJ/mol, which was lower than those of other transparent p-type semiconductors such as CuAlO 2 and CuGaO 2 . The low decomposition temperature and activation energy for decomposition indicate that chemical stability of SrCu 2 O 2 is far lower than those of other p-type conducting oxides.

Identifying transition rates of ionic channels via observations at a single state

CERN Document Server

Deng Ying Chun; Qian Min Ping; Feng Jian Feng

2003-01-01

We consider how to determine all transition rates of an ion channel when it can be described by a birth-death chain or a Markov chain on a star-graph with continuous time. It is found that all transition rates are uniquely determined by the distribution of its lifetime and death-time histograms at a single state. An algorithm to calculate the transition rates exactly, based on the statistics of the lifetime and death-time of the Markov chain at the state, is provided. Examples to illustrate how an ion channel activity is fully determined by the observation of a single state of the ion channel are included.

Identifying transition rates of ionic channels via observations at a single state

International Nuclear Information System (INIS)

Deng Yingchun; Peng Shenglun; Qian Minping; Feng Jianfeng

2003-01-01

We consider how to determine all transition rates of an ion channel when it can be described by a birth-death chain or a Markov chain on a star-graph with continuous time. It is found that all transition rates are uniquely determined by the distribution of its lifetime and death-time histograms at a single state. An algorithm to calculate the transition rates exactly, based on the statistics of the lifetime and death-time of the Markov chain at the state, is provided. Examples to illustrate how an ion channel activity is fully determined by the observation of a single state of the ion channel are included

Identifying transition rates of ionic channels via observations at a single state

Energy Technology Data Exchange (ETDEWEB)

Deng Yingchun [School of Mathematics, Peking University, Beijing (China); Peng Shenglun [School of Mathematics, Peking University, Beijing (China); Qian Minping [School of Mathematics, Peking University, Beijing (China); Feng Jianfeng [COGS, Sussex University, Brighton (United Kingdom)

2003-02-07

We consider how to determine all transition rates of an ion channel when it can be described by a birth-death chain or a Markov chain on a star-graph with continuous time. It is found that all transition rates are uniquely determined by the distribution of its lifetime and death-time histograms at a single state. An algorithm to calculate the transition rates exactly, based on the statistics of the lifetime and death-time of the Markov chain at the state, is provided. Examples to illustrate how an ion channel activity is fully determined by the observation of a single state of the ion channel are included.

Effectiveness of Sr-binders tested using an in vitro model

International Nuclear Information System (INIS)

Hansen, Hanne S.; Eikelman, Margrethe; Hove, Knut

2008-01-01

Full text: The radioisotope 90 Sr is a fission product that in biological systems will behave like calcium and accumulate in bone. Because of the dose effect and the long biological half life of radiostrontium in humans the best countermeasure is to avoid absorption. Low levels of radiostrontium in food products are therefore necessary. To obtain food products, particularly milk, with low radiostrontium levels, the use of Sr-binders in animals may be required. We have tested a number of potential Sr-binders that may be used in animal production. Preliminary studies testing the Sr-binding effect of several compounds in goats demonstrated that only zeolite A(Na) and zeolite P would be of practical interest. Given at a rate of up to 30 g/d the Sr transfer to milk was reduced by 40%. However, because of the chemical properties of the zeolites, they may also bind other cations like Ca, Mg, Cu and Zn, all important minerals for animals. We have therefore tested the binding kinetics of Sr, Ca and Mg by the zeolites in rumen liquid from cows. We used 85 Sr to measure Sr binding and the stable elements of Ca and Mg naturally present in the rumen liquid to measure the binding of these minerals. In the rumen liquid mixture the pH was varied to simulate the pH variation in the digestive system of ruminants and the binding of the minerals to the zeolites were measured at each step. The time dependant 85 Sr binding showed that zeolite A(Na), at 0.5% in rumen liquid, pH 7.3, bound 98% of the 85 Sr already after 10 min. This proportion of Sr binding was persistent for the tested period of 24 h. The zeolite P at 0.5% in rumen liquid, pH 7.3, bound ca 85% and had a similar time dependant behavior. When pH was reduced to 2.5, similar to the pH in the abomasum, no Sr was bound to the zeolites. This was also the case at pH 3 and 4. At pH 5 ca 10% of the Sr was bound. Theses levels of pH simulated the conditions in the small intestine. To simulate the conditions in the large intestine

Synthesis, crystal structure, and ionic conductivity of a new layered metal phosphate, Li2Sr2Al(PO4)3

International Nuclear Information System (INIS)

Kim, Sung-Chul; Kwak, Hyun-Jung; Yoo, Chung-Yul; Yun, Hoseop; Kim, Seung-Joo

2016-01-01

A new layered metal phosphate, Li 2 Sr 2 Al(PO 4 ) 3 , was synthesized in the form of either a single-crystal or polycrystalline powder using the molten hydroxide flux method or a solid-state reaction, respectively. Li 2 Sr 2 Al(PO 4 ) 3 crystallizes to the P2 1 /n (Z=4) monoclinic space group with lattice parameters a≈4.95 Å, b≈22.06 Å, c≈8.63 Å, and β≈91.5°. The structure is composed of stacked [LiSrAl(PO 4 ) 2 ] layers alternating regularly with [LiSrPO 4 ] layers. In the [LiSrAl(PO 4 ) 2 ] sublattice, the AlO 6 octahedra and PO 4 tetrahedra are tilted cooperatively to form an anionic, corrugated, two-dimensional [Al(PO 4 ) 2 ] 3− framework that can be regarded as a “distorted-glaserite” structure. The [LiSrPO 4 ] sublattice is that of a layered block containing a six-membered ring formed from alternating linkages of LiO 4 and PO 4 tetrahedra. The six-membered rings show a boat-type arrangement with the up(U) or down(D) pointing sequence, UUDUUD. The interspace between the two sublattices generates a two-dimensional pathway for Li + ion conduction. The impedance measurement indicated that Li 2 Sr 2 Al(PO 4 ) 3 had a moderate ion conductivity (σ≈1.30×10 −4 S cm −1 at 667 K), with an activation energy E a ≈1.02 eV. - Graphical abstract: Polyhedral view of Li 2 Sr 2 Al(PO 4 ) 3 . Li + ions are represented by green spheres, Sr atoms by white spheres, AlO 6 groups by octahedra, and PO 4 groups by tetrahedra. - Highlights: • New compound Li 2 Sr 2 Al(PO 4 ) 3 is reported. • The crystal structure is investigated by single-crystal XRD analysis. • The structure is formed by the alternate stacking of two different sublattices. • Correlation between the crystal structure and ionic conductivity is discussed.

87Sr/86Sr dating and preliminary interpretation of magnetic susceptibility logs of giant piston cores from the Rio Grande Rise in the South Atlantic

Science.gov (United States)

Lacasse, Christian Michel; Santos, Roberto Ventura; Dantas, Elton Luiz; Vigneron, Quentin; de Sousa, Isabela Moreno Cordeiro; Harlamov, Vadim; Lisniowski, Maria Aline; Pessanha, Ivo Bruno Machado; Frazão, Eugênio Pires; Cavalcanti, José Adilson Dias

2017-12-01

Giant piston cores recovered from shallow depths (optimized matching with an internationally recognized timescale of 87Sr/86Sr seawater variation through geological times. Depth-to-age conversion of the magnetic susceptibility logs was implemented based on the identification of correlative peaks between cores and the developed 87Sr/86Sr age model. The influence of Northern Hemisphere glaciation is reflected in these new stratigraphic logs by a gradual increase from ∼2.7 Ma in the lower signal of magnetic susceptibility (below background level), to values approaching the arithmetic means, likely reflecting an overall increase in terrigenous input. The Rio Grande Rise cores have very low Plio-Pleistocene sedimentation rates (∼0.4-0.8 cm/ka), similar to gravity cores from the oligotrophic subtropical South Atlantic (below ∼2000 mbsl), and for which an inverse correlation between carbonate content and magnetic susceptibility was established. The coring depths on the Rio Grande Rise encompass strong gradients in oxygen concentration and other seawater parameters that define today's AAIW/UCDW transition. Depth-dependent variation in sedimentation rates since the onset of Northern Hemisphere glaciation coincides with the incursion of intermediate waters (UCDW, AAIW) in response to the overall reduction of NADW export to the Southern Ocean. Background levels of magnetic susceptibility in the cores suggest that this variation is mainly attributed to terrigenous input. The source region of this material has yet to be traced by considering in particular the mineral composition and paramagnetic properties of the detrital clays.

New aragonite 87Sr/86Sr records of Mesozoic ammonoids and approach to the problem of N, O, C and Sr isotope cycles in the evolution of the Earth

Science.gov (United States)

Zakharov, Yuri D.; Dril, Sergei I.; Shigeta, Yasunari; Popov, Alexander M.; Baraboshkin, Eugenij Y.; Michailova, Irina A.; Safronov, Peter P.

2018-02-01

New Sr isotope data from well-preserved aragonite ammonoid shell material from the Mesozoic are compared with that from a living Nautilus shell. The prominent negative Sr isotope excursions known from the Middle Permian, Jurassic and Cretaceous probably have their origins in intensive plate tectonic activity, followed by enhanced hydrothermal activity at the mid-ocean ridges (mantle volcanism) which supplied low radiogenic Sr to seawater. The maximum positive (radiogenic) shift in the lower Mesozoic Sr isotope curve (Lower Triassic peak) was likely caused by a significant expansion of dry land surfaces (Dabie-Sulu Triassic orogeny) and their intensive silicate weathering in conditions of extreme warming and aridity in the very end of the Smithian, followed by warm and humid conditions in the late Spathian, which apparently resulted in a significant oceanic input of radiogenic Sr through riverine flux. The comparatively high 87Sr/86Sr ratio obtained from the living Nautilus shell is probably a function of both the Alpine orogeny, which was accompanied by significant continental weathering and input of radiogenic Sr to the oceans, and the weakening of mantle volcanism.

Over-expression of SR-cyclophilin, an interaction partner of nuclear pinin, releases SR family splicing factors from nuclear speckles

International Nuclear Information System (INIS)

Lin, C.-L.; Leu, Steve; Lu, M.-C.; Ouyang Pin

2004-01-01

Pre-mRNA splicing takes place within a dynamic ribonucleoprotein particle called the spliceosome and occurs in an ordered pathway. Although it is known that spliceosome consists of five small nuclear RNAs and at least 50 proteins, little is known about how the interaction among the proteins changes during splicing. Here we identify that SR-cyp, a Moca family of nuclear cyclophilin, interacts and colocalizes with nuclear pinin (pnn), a SR-related protein involving in pre-mRNA splicing. Nuclear pnn interacts with SR-cyp via its C-terminal RS domain. Upon SR-cyp over-expression, however, the subnuclear distribution of nuclear pnn is altered, resulting in its redistribution from nuclear speckles to a diffuse nucleoplasmic form. The diffuse subnuclear distribution of nuclear pnn is not due to epitope masking, accelerated protein turnover or post-translational modification. Furthermore, we find that SR-cyp regulates the subnuclear distribution of other SR family proteins, including SC35 and SRm300, in a similar manner as it does on nuclear pnn. This result is significant because it suggests that SR-cyp plays a general role in modulating the distribution pattern of SR-like and SR proteins, similar to that of Clk (cdc2-like kinase)/STY on SR family splicing factors. SR-cyp might direct its effect via either alteration of protein folding/conformation or of protein-protein interaction and thus may add another control level of regulation of SR family proteins and modification of their functions

Estimation of Joule heating and its role in nonlinear electrical response of Tb0.5Sr0.5MnO3 single crystal

Science.gov (United States)

Nhalil, Hariharan; Elizabeth, Suja

2016-12-01

Highly non-linear I-V characteristics and apparent colossal electro-resistance were observed in non-charge ordered manganite Tb0.5Sr0.5MnO3 single crystal in low temperature transport measurements. Significant changes were noticed in top surface temperature of the sample as compared to its base while passing current at low temperature. By analyzing these variations, we realize that the change in surface temperature (ΔTsur) is too small to have caused by the strong negative differential resistance. A more accurate estimation of change in the sample temperature was made by back-calculating the sample temperature from the temperature variation of resistance (R-T) data (ΔTcal), which was found to be higher than ΔTsur. This result indicates that there are large thermal gradients across the sample. The experimentally derived ΔTcal is validated with the help of a simple theoretical model and estimation of Joule heating. Pulse measurements realize substantial reduction in Joule heating. With decrease in sample thickness, Joule heating effect is found to be reduced. Our studies reveal that Joule heating plays a major role in the nonlinear electrical response of Tb0.5Sr0.5MnO3. By careful management of the duty cycle and pulse current I-V measurements, Joule heating can be mitigated to a large extent.

Computer control system of the superconducting SR-light source ''Aurora''

International Nuclear Information System (INIS)

Yamada, H.

1989-01-01

The Aurora is a compact SR-light system optimized for x-ray lithography. The system includes a superconducting electron storage ring, a 150-MeV race track microtron as an injector, and light beamlines. The SR-ring features a single magnet body, in which the 650-MeV electron beam orbits a true circular trajectory of 1 m diameter. The computer control system developed for Aurora has a three-level hierarchical architecture. The top level is the Central Intelligence System, and the second an Autonomic Control System (ACS). The bottom is an assembly of distributed local controllers linked to the ACS level through optical fibers. This system provides fully automatic and remote operation, and a powerful machine study capability through the associated man--machine console and the interpretive operation language

Computer control system of the superconducting SR-light source ``Aurora''

Science.gov (United States)

Yamada, Hironari

1989-07-01

The Aurora is a compact SR-light system optimized for x-ray lithography. The system includes a superconducting electron storage ring, a 150-MeV race track microtron as an injector, and light beamlines. The SR-ring features a single magnet body, in which the 650-MeV electron beam orbits a true circular trajectory of 1 m diameter. The computer control system developed for Aurora has a three-level hierarchical architecture. The top level is the Central Intelligence System, and the second an Autonomic Control System (ACS). The bottom is an assembly of distributed local controllers linked to the ACS level through optical fibers. This system provides fully automatic and remote operation, and a powerful machine study capability through the associated man-machine console and the interpretive operation language.

Low-temperature specific heat of single-crystal Bi2CaSr2Cu2O8 and Tl2Ca2Ba2Cu3O10

International Nuclear Information System (INIS)

Urbach, J.S.; Mitzi, D.B.; Kapitulnik, A.; Wei, J.Y.T.; Morris, D.E.; Physics Division, Lawrence Berkeley Laboratory, University of California, Berkeley, California 94720)

1989-01-01

We report specific-heat measurements from 2 to 15 K on single crystals of Bi 2 CaSr 2 Cu 2 O 8 and Tl 2 Ca 2 Ba 2 Cu 3 O 10 We find low-temperature deviations from the Debye law that can be attributed to spin-glass behavior of a small concentration of isolated impurity copper moments. At higher temperatures, we observe contributions to the specific heat that can be attributed to a soft-phonon mode, possibly associated with the superstructure in the Bi-O and Tl-O layers. From our single-crystal data, we conclude that the thallium- and bismuth-based copper oxide superconductors show no measurable linear term in the specific heat [γ(0) less than or equal to 1 mJ/mole K 2

Sequential determination of {sup 239,240}Pu, {sup 238} Pu, {sup 241} Am and {sup 90}Sr in radioactive wastes using SPE sorbents Analig Pu02, AnaLig Sr01 and TRU Resin; Sekvencne stanovenie {sup 239,240}Pu, {sup 238} Pu, {sup 241} Am a {sup 90}Sr v radioaktivnych odpadoch pouzitim SPE sorbentov Analig Pu02, AnaLig Sr01 a TRU Resin

Energy Technology Data Exchange (ETDEWEB)

Durkot, E; Dulanska, S [Univerzita Komenskeho v Bratislave, Prirodovedecka fakulta, Katedra jadrovej chemie, 84215 Bratislava (Slovakia)

2012-04-25

A simple and rapid method of the sequential determination of radionuclides {sup 239,240}Pu, {sup 238} Pu, {sup 241} Am and {sup 90}Sr in radioactive sludge from the NPP Bohunice A1 with high radiochemical yields and efficient removal of interfering components from a matrix was developed. Separation method combines SPE sorbents Analig Pu02, AnaLig Sr01 made by IBC Advanced Technologies and TRU Resin (Eichrom Technologies) placed in tandem. Advantage of a single-stage column located on the vacuum box with a rapid flow is an effective pre-concentration and separation of radionuclides and minimization of sample separation time. (authors)

89Sr and 90Sr in atmospheric precipitations in May 1986 in Bucharest-Magurele area

International Nuclear Information System (INIS)

Paunescu, N.; Vata, I.

1987-08-01

Sr-89 and Sr-90 were determined in the fallout of May 1986. The maximum values of 335 Bq/(m 2 * 6 hours) and 110 Bq/(m 2 * 6 hours) were observed at May 2 and 5. Throughout May 1986 a quantity of 860 Bq/m 2 of Sr-90 deposited from the fallout in the Bucharest -Magurele area was determined. (authors)

Single-layer TiO x reconstructions on SrTiO₃ (111): (√7 × √7)R19.1°, (√13 × √13)R13.9°, and related structures

Energy Technology Data Exchange (ETDEWEB)

Andersen, Tassie K.; Wang, Shuqiu; Castell, Martin R.; Fong, Dillon D.; Marks, Laurence D.

2018-09-01

The atomic structures of two reconstructions, (√7 × √7)R19.1° and (√13 × √13)R13.9°, on the SrTiO₃ (111) surface were determined using a combination of density functional theory and scanning tunneling microscopy data and simulations. The combination of these methods allows for potential surface structures to be generated and verified in the absence of diffraction data, providing another tool for solving surface reconstructions. These reconstructions belong to the same stoichiometric, nSrTiO₃ • mTiO₂, structural family made up of an interconnected, single layer of edge-sharing TiO₆ and TiO₅[] octahedra. This family is found to include the previously-solved (2 × 2)a reconstruction as its smallest unit-cell sized member and serves as a tool for better understanding and predicting the structure of other reconstructions of arbitrary surface unit-cell size on SrTiO₃ (111). This reconstruction family and the calculations of surface energies for different hypothesis structures also shed light on the structure of Schottky defects observed on these reconstructed SrTO₃ (111) surfaces.

Testing the fidelity of the Sr/Ca proxy in recording ocean temperature in a western Atlantic coral

Science.gov (United States)

Kuffner, I. B.; Roberts, K.; Flannery, J. A.; Richey, J. N.; Morrison, J. M.

2017-12-01

Massive corals provide a useful archive of environmental variability, but careful testing of geochemical proxies in corals is necessary to validate the relationship between each proxy and environmental parameter throughout the full range of conditions experienced by the recording organisms. Here we use samples from a field-based coral-growth study to test the hypothesis that Sr/Ca in the coral Siderastrea siderea accurately records sea-surface temperature (SST) in the subtropics (Florida, USA) along 350 km of reef tract. We test calcification rate, measured via buoyant weight, and linear extension (LE) rate, estimated with Alizarin Red-S staining, as predictors of variance in the Sr/Ca records of 39 individual S. siderea corals grown at four outer-reef locations next to in-situ temperature loggers during two, year-long periods. We found that corals with calcification rates less than 1.7 mg cm-2 d-1 or LE rates less than 1.7 mm yr-1 returned spuriously high Sr/Ca values, leading to a cold bias in Sr/Ca-based SST estimates. The threshold-type response curves suggest that LE rate can be used as a quality-control indicator during sample and microdrill-path selection when using long cores for SST paleoreconstruction. For our corals that passed this quality control step, the Sr/Ca-SST proxy performed well in estimating mean annual SST across three sites spanning 350 km of the Florida reef tract. However, there was some evidence that extreme temperature stress in 2010 (cold snap) and 2011 (SST above coral-bleaching threshold) may have caused the corals not to record the temperature extremes. Known stress events could be avoided during modern calibrations of paleoproxies.

Computing Relative Free Energies of Solvation using Single Reference Thermodynamic Integration Augmented with Hamiltonian Replica Exchange.

Science.gov (United States)

Khavrutskii, Ilja V; Wallqvist, Anders

2010-11-09

This paper introduces an efficient single-topology variant of Thermodynamic Integration (TI) for computing relative transformation free energies in a series of molecules with respect to a single reference state. The presented TI variant that we refer to as Single-Reference TI (SR-TI) combines well-established molecular simulation methodologies into a practical computational tool. Augmented with Hamiltonian Replica Exchange (HREX), the SR-TI variant can deliver enhanced sampling in select degrees of freedom. The utility of the SR-TI variant is demonstrated in calculations of relative solvation free energies for a series of benzene derivatives with increasing complexity. Noteworthy, the SR-TI variant with the HREX option provides converged results in a challenging case of an amide molecule with a high (13-15 kcal/mol) barrier for internal cis/trans interconversion using simulation times of only 1 to 4 ns.

87Sr/86Sr ratios in hydrothermal waters and deposits from the east pacific rise at 210N

International Nuclear Information System (INIS)

Albarede, F.; Michard, A.; Minster, J.F.; Michard, G.

1981-01-01

87 Sr/ 86 Sr ratios of three hydrothermal waters collected on the East Pacific Rise at 21 0 N define a mixing line between seawater and a hydrothermal end-member at 0.7030 which is derived by seawater-basalt interaction at ca. 350 0 C and water/rock ratio of about 1.5. Sr concentrations are not affected in the process while Mg uptake from seawater is almost complete. Up to 2/3 of this hydrothermal component is involved in anhydrite precipitation while the Sr isotopic ratio in sulfides (chalcopyrite + sphalerite) cannot be distinguished from that of sulfate. It is estimated that ca. 1 x 10 10 moles of strontium are yearly cycled in the hydrothermal systems of mid-oceanic ridges, thereby affecting the 87 Sr/ 86 Sr budget of seawater. Mass balance between river runoff, limestone precipitation and ridge basalt alteration suggests that the 87 Sr/ 86 Sr ratios of the river runoff are in the range 0.7097-0.7113, and are largely dominated by limestone alteration. (orig.)

Synthetic clay excels in 90Sr removal

International Nuclear Information System (INIS)

Komarneni, Sridhar; Kodama, Tatsuya; Paulus, William J.; Carlson, C.

2000-01-01

Tests with actual ground water from Hanford site, and fundamental studies of 2Na + →Sr 2+ exchange equilibria revealed that a synthetic clay is extremely selective for 90 Sr with a high capacity for uptake. Comparative studies with existing Sr selective ion exchangers clearly revealed that the present synthetic clay exhibited the best performance for 90 Sr removal from actual ground water collected from three different locations at Hanford. This novel Sr ion sieve is expected to be useful for the decontamination of the environment after accidental release and contamination with 90 Sr. (c) 2000 Materials Research Society

Synthesis of pure and Sr-doped LaGaO{sub 3}, LaFeO{sub 3} and LaCoO{sub 3} and Sr,Mg-doped LaGaO{sub 3} for ITSOFC application using different wet chemical routes

Energy Technology Data Exchange (ETDEWEB)

Kumar, M. [National Metallurgical Laboratory-Madras Center, CSIR Madras Complex, Chennai 600113 (India); Srikanth, S. [National Metallurgical Laboratory-Madras Center, CSIR Madras Complex, Chennai 600113 (India)], E-mail: s_srikanth_99@yahoo.com; Ravikumar, B.; Alex, T.C.; Das, S.K. [National Metallurgical Laboratory, Jamshedpur 831007 (India)

2009-02-15

Pure and Sr-doped LaGaO{sub 3}, LaFeO{sub 3} and LaCoO{sub 3} and Sr,Mg-doped LaGaO{sub 3} were synthesized by various wet chemical routes, namely combustion, co-precipitation and citrate-gel methods. The effect of the various process parameters on the phase purity, particle size and surface area and morphology of the synthesized powders were determined by XRD, simultaneous TG-DTA, laser light scattering, BET and scanning electron microscopy. The stability of the synthesized pure phases in oxidizing and reducing atmosphere was also studied by thermogravimetry. It was observed that pure and Sr-doped single perovskite phases of lanthanum ferrite, cobaltite and gallate and Sr,Mg-doped lanthanum gallate could be synthesized by combustion and citrate-gel methods under suitable process conditions. Synthesis using the co-precipitation method yielded incomplete reaction irrespective of the calcination temperature adopted. The citrate-gel method yielded better powder properties in terms of particle size and morphology and surface area compared to combustion synthesis. It was found that pure and Sr-doped lanthanum ferrite, lanthanum cobaltite, lanthanum gallate and Sr,Mg-doped lanthanum gallate were stable in the oxidizing atmosphere. In the reducing atmosphere, pure and Sr-doped lanthanum ferrite and Sr,Mg-doped lanthanum gallate was found to be stable at least during the timeframe of the thermogravimetric experiment whereas pure and Sr-doped lanthanum cobaltite was partially reduced in hydrogen atmosphere.

Single-row vs. double-row arthroscopic rotator cuff repair: clinical and 3 Tesla MR arthrography results

Science.gov (United States)

2013-01-01

Background Arthroscopic rotator cuff repair has become popular in the last few years because it avoids large skin incisions and deltoid detachment and dysfunction. Earlier arthroscopic single-row (SR) repair methods achieved only partial restoration of the original footprint of the tendons of the rotator cuff, while double-row (DR) repair methods presented many biomechanical advantages and higher rates of tendon-to-bone healing. However, DR repair failed to demonstrate better clinical results than SR repair in clinical trials. MR imaging at 3 Tesla, especially with intra-articular contrast medium (MRA), showed a better diagnostic performance than 1.5 Tesla in the musculoskeletal setting. The objective of this study was to retrospectively evaluate the clinical and 3 Tesla MRA results in two groups of patients operated on for a medium-sized full-thickness rotator cuff tear with two different techniques. Methods The first group consisted of 20 patients operated on with the SR technique; the second group consisted of 20 patients operated on with the DR technique. All patients were evaluated at a minimum of 3 years after surgery. The primary end point was the re-tear rate at 3 Tesla MRA. The secondary end points were the Constant-Murley Scale (CMS), the Simple Shoulder Test (SST) scores, surgical time and implant expense. Results The mean follow-up was 40 months in the SR group and 38.9 months in the DR group. The mean postoperative CMS was 70 in the SR group and 68 in the DR group. The mean SST score was 9.4 in the SR group and 10.1 in the DR group. The re-tear rate was 60% in the SR group and 25% in the DR group. Leakage of the contrast medium was observed in all patients. Conclusions To the best of our knowledge, this is the first report on 3 Tesla MRA in the evaluation of two different techniques of rotator cuff repair. DR repair resulted in a statistically significant lower re-tear rate, with longer surgical time and higher implant expense, despite no

Single-row vs. double-row arthroscopic rotator cuff repair: clinical and 3 Tesla MR arthrography results

Directory of Open Access Journals (Sweden)

Tudisco Cosimo

2013-01-01

Full Text Available Abstract Background Arthroscopic rotator cuff repair has become popular in the last few years because it avoids large skin incisions and deltoid detachment and dysfunction. Earlier arthroscopic single-row (SR repair methods achieved only partial restoration of the original footprint of the tendons of the rotator cuff, while double-row (DR repair methods presented many biomechanical advantages and higher rates of tendon-to-bone healing. However, DR repair failed to demonstrate better clinical results than SR repair in clinical trials. MR imaging at 3 Tesla, especially with intra-articular contrast medium (MRA, showed a better diagnostic performance than 1.5 Tesla in the musculoskeletal setting. The objective of this study was to retrospectively evaluate the clinical and 3 Tesla MRA results in two groups of patients operated on for a medium-sized full-thickness rotator cuff tear with two different techniques. Methods The first group consisted of 20 patients operated on with the SR technique; the second group consisted of 20 patients operated on with the DR technique. All patients were evaluated at a minimum of 3 years after surgery. The primary end point was the re-tear rate at 3 Tesla MRA. The secondary end points were the Constant-Murley Scale (CMS, the Simple Shoulder Test (SST scores, surgical time and implant expense. Results The mean follow-up was 40 months in the SR group and 38.9 months in the DR group. The mean postoperative CMS was 70 in the SR group and 68 in the DR group. The mean SST score was 9.4 in the SR group and 10.1 in the DR group. The re-tear rate was 60% in the SR group and 25% in the DR group. Leakage of the contrast medium was observed in all patients. Conclusions To the best of our knowledge, this is the first report on 3 Tesla MRA in the evaluation of two different techniques of rotator cuff repair. DR repair resulted in a statistically significant lower re-tear rate, with longer surgical time and higher implant

Single-row vs. double-row arthroscopic rotator cuff repair: clinical and 3 Tesla MR arthrography results.

Science.gov (United States)

Tudisco, Cosimo; Bisicchia, Salvatore; Savarese, Eugenio; Fiori, Roberto; Bartolucci, Dario A; Masala, Salvatore; Simonetti, Giovanni

2013-01-27

Arthroscopic rotator cuff repair has become popular in the last few years because it avoids large skin incisions and deltoid detachment and dysfunction. Earlier arthroscopic single-row (SR) repair methods achieved only partial restoration of the original footprint of the tendons of the rotator cuff, while double-row (DR) repair methods presented many biomechanical advantages and higher rates of tendon-to-bone healing. However, DR repair failed to demonstrate better clinical results than SR repair in clinical trials. MR imaging at 3 Tesla, especially with intra-articular contrast medium (MRA), showed a better diagnostic performance than 1.5 Tesla in the musculoskeletal setting. The objective of this study was to retrospectively evaluate the clinical and 3 Tesla MRA results in two groups of patients operated on for a medium-sized full-thickness rotator cuff tear with two different techniques. The first group consisted of 20 patients operated on with the SR technique; the second group consisted of 20 patients operated on with the DR technique. All patients were evaluated at a minimum of 3 years after surgery. The primary end point was the re-tear rate at 3 Tesla MRA. The secondary end points were the Constant-Murley Scale (CMS), the Simple Shoulder Test (SST) scores, surgical time and implant expense. The mean follow-up was 40 months in the SR group and 38.9 months in the DR group. The mean postoperative CMS was 70 in the SR group and 68 in the DR group. The mean SST score was 9.4 in the SR group and 10.1 in the DR group. The re-tear rate was 60% in the SR group and 25% in the DR group. Leakage of the contrast medium was observed in all patients. To the best of our knowledge, this is the first report on 3 Tesla MRA in the evaluation of two different techniques of rotator cuff repair. DR repair resulted in a statistically significant lower re-tear rate, with longer surgical time and higher implant expense, despite no difference in clinical outcomes. We think that

Type II superconductivity in SrPd2Ge2

International Nuclear Information System (INIS)

Samuely, T; Szabó, P; Pribulová, Z; Samuely, P; Sung, N H; Cho, B K; Klein, T; Cambel, V; Rodrigo, J G

2013-01-01

Previous investigations have shown that SrPd 2 Ge 2 , a compound isostructural with ‘122’ iron pnictides but iron and pnictogen free, is a conventional superconductor with a single s-wave energy gap and a strongly three-dimensional electronic structure. In this work we reveal the Abrikosov vortex lattice formed in SrPd 2 Ge 2 when exposed to magnetic field by means of scanning tunneling microscopy and spectroscopy. Moreover, by examining the differential conductance spectra across a vortex and estimating the upper and lower critical magnetic fields by tunneling spectroscopy and local magnetization measurements, we show that SrPd 2 Ge 2 is a strong type II superconductor with κ ≫ 2 −1/2 . Also, we compare the differential conductance spectra in various magnetic fields to the pair-breaking model of Maki and de Gennes for a dirty limit type II superconductor in the gapless region. This way we demonstrate that the type II superconductivity is induced by the sample being in the dirty limit, while in the clean limit it would be a type I superconductor with κ ≪ 2 −1/2 , in concordance with our previous study (Kim et al (2012) Phys. Rev. B 85 014520). (paper)

Sintering and characterization of SrBi_2Ta_2O_9 obtained by high-pressure processing at low temperatures

International Nuclear Information System (INIS)

Souza, Ricson R.; Kirchner, Rejane K.; Jurado, Jose R.; Pereira, Altair S.; Sousa, Vânia C.

2016-01-01

High-pressure processing is a very attractive approach for the production of materials with new and/or improved properties. In this work, pressures in the order of 7.7 GPa and 2.5 GPa were induced in SrBi_2Ta_2O_9 samples at different temperatures placed in a specific reaction cell and generated different effects on phase formation. The microstructural evolution during high-pressure processing was investigated by scanning electron microscopy in association with energy dispersion spectroscopy and with the support of an X-ray diffraction analyzer. Frequency response analysis was used to obtain the dielectric curves by electrochemical impedance spectroscopy. A SrBi_2Ta_2O_9 single-phase sample, treated at 2.5 GPa and 900 °C, was used to evaluate the electrical properties, obtaining a dielectric response similar to SrBi_2Ta_2O_9 samples sintered by conventional processes at temperatures above 1000 °C. In addition, by this method, it was possible to obtain ceramics with uniform microstructure and a relative density of 93%. - Highlights: • The first production of SrBi_2Ta_2O_9 using the technique of high-pressure processing. • The ability to produce single-phase SrBi_2Ta_2O_9 treated at 2.5 GPa and 900 °C. • The electrical properties are compatible with SBT sintered at high temperatures.

Oriented growth of Sr n+1Ti n O3n+1 Ruddlesden-Popper phases in chemical solution deposited thin films

International Nuclear Information System (INIS)

Gutmann, Emanuel; Levin, Alexandr A.; Reibold, Marianne; Mueller, Jan; Paufler, Peter; Meyer, Dirk C.

2006-01-01

Oriented thin films of perovskite-related Sr n +1 Ti n O 3 n +1 Ruddlesden-Popper phases (n=1, 2, 3) were grown on (001) single-crystalline SrTiO 3 substrates. Preparation of the films was carried out by wet chemical deposition from metalorganic Sr-Ti solutions (rich in Sr) and subsequent conversion into the crystalline state by thermal treatment in air atmosphere at a maximum temperature of 700 deg. C. Solutions were prepared by a modified Pechini method. The films were investigated by wide-angle X-ray scattering and high-resolution transmission electron microscopy. The phase content of powders prepared from the dried solutions and annealed under similar conditions differed from that present in the films, i.e. only polycrystalline SrTiO 3 was detected together with oxides of Ti and Sr. - Graphical abstract: Cross-sectional image of an oriented chemical solution deposited thin film obtained by high-resolution transmission electron microscopy. Periodical spacings corresponding to SrTiO 3 substrate (right) and Sr 2 TiO 4 Ruddlesden-Popper phase (n=1) film region (left) are marked

Influence of variations in dose and dose rates on biological effects of inhaled beta-emitting radionuclides

International Nuclear Information System (INIS)

McClellan, R.O.; Benjamin, S.A.; Boecker, B.B.; Hahn, F.F.; Hobbs, C.H.; Jones, R.K.; Lundgren, D.L.

1976-01-01

The biological effects of inhaled β-emitting radionuclides, 90 Y, 91 Y, 144 Ce and 90 Sr, are being investigated in beagle dogs that received single acute exposures at 12 to 14 months of age. The aerosols studied have included 91 YC1 3 , 144 CeC1 3 , 90 SrC1 2 , and 90 Y, 91 Y, 144 Ce or 90 Sr in aluminosilicate particles. Thus, 91 YCl 3 , 144 CeCl 3 and the aluminosilicate containing radionuclide particles all resulted in significant exposures to lung; 91 YC1 3 , 144 CeC1 3 an 90 SrC1 2 resulted in significant exposures to bone; 91 YC1 3 and 144 CeC1 3 resulted in significant exposures to liver. The higher initial doserate exposures have been more effective than low dose-rate exposures on a per-rad basis in producing early effects. To date ( 144 CeO 2 , it was observed that, on a μCi initial lung burden per kilogram body weight basis, mice did not develop pulmonary tumours whereas beagle dogs did. To fid out the reason for this observation mice have been repeatedly exposed by inhalation to 144 CeO 2 to maintain lung burdens of 144 Ce that resulted in radiation dose rates similar to that observed in beagle dogs. Several of the repeatedly exposed mice developed malignant pulmonary tumours. Thus, with similar dose rates and cumulative doses to the lung, mice and dogs responded in a similar manner to chronic β radiation

Enthalpies of formation of Cd0.917Sr0.083, Cd0.857Sr0.143 and Cd0.667Sr0.333 intermetallic compounds

International Nuclear Information System (INIS)

Agarwal, Renu; Singh, Ziley

2008-01-01

Cadmium is expected to be the solvent for pyrochemical processing of the metallic nuclear fuel. Therefore, thermodynamic properties of cadmium with various fuel and clad elements are of interest. Enthalpies of formation of the intermetallic compounds of Cd-Sr system, Cd 0.917 Sr 0.083 , Cd 0.857 Sr 0.143 and Cd 0.667 Sr 0.333 were determined by precipitation using Calvet calorimeter. Enthalpies of formation of the compounds were found to be -3.05 ± 0.5 kJ mol -1 at 723 K, -14.2 ± 0.7 kJ mol -1 at 843 K and -28.4 ± 0.8 kJ mol -1 at 863 K, respectively. Enthalpies of formation of Cd 0.917 Sr 0.083 and Cd 0.857 Sr 0.143 were also determined by partial enthalpy of formation measurements and the values were found to be -3.9 ± 1.1 kJ mol -1 at 723 K and -13.42 ± 1.2 kJ mol -1 at 843 K, respectively. Miedema model was used to estimate the enthalpies of formation of these compounds and the estimated values were compared with the experimentally determined values

Magnetic heat transport in Sr{sub 2}IrO{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Steckel, Frank [Leibniz Institute for Solid State and Materials Research, IFW Dresden (Germany); Takagi, Hidenori [Max-Planck-Institute for Solid State Research, Stuttgart (Germany); Buechner, Bernd; Hess, Christian [Leibniz Institute for Solid State and Materials Research, IFW Dresden (Germany); Center for Transport and Devices, TU Dresden (Germany)

2015-07-01

The layered perovskite Sr{sub 2}IrO{sub 4} is a 5d transition metal oxide with an enhanced spin-orbit coupling leading to a Mott insulating ground state with J{sub eff}=(1)/(2). It exhibits canted antiferromagnetism below T{sub N}=240 K with an antiferromagnetic coupling constant of about J=0.1 eV. Thermal conductivity measurements along the ab plane of a Sr{sub 2}IrO{sub 4} single crystal provide evidence for a contribution of magnons (below T{sub N}) to the thermal conductivity, similar to that of the isostructural 2D S=(1)/(2) Heisenberg antiferromagnet La{sub 2}CuO{sub 4}, where a significant magnonic contribution to the heat transport is known.

Synthesis of Bi2Sr2CaCu2O8+δ whiskers and cross-whisker intrinsic Josephson junction

International Nuclear Information System (INIS)

Hatano, T.; Takano, Y.; Arisawa, S.; Ishii, A.; Togano, K.; Fukuyo, A.

2001-01-01

A synthesis technique of Bi 2 Sr 2 CaCu 2 O 8+δ single-crystal whiskers was studied. The whiskers were synthesized by heating glassy melt-quenched Bi-Sr-Ca-Cu-O (3:2:2:4 in cationic ratio) plates. The atmospheric condition of the whisker growth, especially oxygen partial pressure and gas flow, was investigated. It was found out that the whisker growth rate shows a maximum at P O2 =2/3 bar. For the crystalline quality of the whiskers, the airtight condition was found to be useful as compared to the conventional oxygen stream condition. The crystalline quality, especially the straightness and morphology of the surface, could be improved by keeping the growing whiskers under the equilibrium P Bi condition. Over 20-mm-long whisker crystals have been successfully synthesized by choosing optimum oxygen partial pressure around the P O2 =2/3 bar in the airtight condition. The growth condition and mechanism of the Bi 2 Sr 2 CaCu 2 O 8+δ whiskers were investigated by an in-situ high-temperature x-ray diffraction analysis and an in-situ high-temperature microscope observation. It was found that the whiskers grow in a partially melted state at a temperature of 10-40 degrees below the melting point. The result obtained demonstrates that Bi 2 Sr 2 CaCu 2 O 8+δ whiskers grow at their bottom by the conventional liquid-phase growth mechanism, as was proposed by Matsubara et al. (author)

Thermodynamic Modeling of Sr/TRU Removal

International Nuclear Information System (INIS)

Felmy, A.R.

2000-01-01

This report summarizes the development and application of a thermodynamic modeling capability designed to treat the Envelope C wastes containing organic complexants. A complete description of the model development is presented. In addition, the model was utilized to help gain insight into the chemical processes responsible for the observed levels of Sr, TRU, Fe, and Cr removal from the diluted feed from tank 241-AN-107 which had been treated with Sr and permanganate. Modeling results are presented for Sr, Nd(III)/Eu(III), Fe, Cr, Mn, and the major electrolyte components of the waste (i.e. NO 3 , NO 2 , F,...). On an overall basis the added Sr is predicted to precipitate as SrCO 3 (c) and the MnO 4 - reduced by the NO 2 - and precipitated as a Mn oxide. These effects result in only minor changes to the bulk electrolyte chemistry, specifically, decreases in NO 2 - and CO 3 2- , and increases in NO 3 - and OH - . All of these predictions are in agreement with the experimental observations. The modeling also indicates that the majority of the Sr, TRU's (or Nd(III)/Eu(III)) analogs, and Fe are tied up with the organic complexants. The Sr and permanganate additions are not predicted to effect these chelate complexes significantly owing to the precipitation of insoluble Mn oxides or SrCO 3 . These insoluble phases maintain low dissolved concentrations of Mn and Sr which do not affect any of the other components tied up with the complexants. It appears that the removal of the Fe and TRU'S during the treatment process is most likely as a result of adsorption or occlusion on/into the Mn oxides or SrCO 3 , not as direct displacement from the complexants into precipitates. Recommendations are made for further studies that are needed to help resolve these issues

Reactivity, structure and physical properties of SrCo{sub 2.5+{delta}} and La{sub 2}CoO{sub 4.0+{delta}}. In situ X-ray diffraction and neutrons study; Reactivite, structure et proprietes physiques de SrCoO{sub 2.5+{delta}} et La{sub 2}CoO{sub 4.0+{delta}}. Etude par diffraction des rayons X et des neutrons in situ

Energy Technology Data Exchange (ETDEWEB)

Le Toquin, R.

2003-11-15

This work was devoted to the study of the reactivity and more specifically the influence of the intercalated oxygen amount {delta} on the structure and physical properties of SrCoO{sub 2.5+{delta}} et La{sub 2}CoO{sub 4.0+{delta}} We controlled the oxidation level by means of reversible electrochemical red ox reaction at room temperature. Structural modifications, especially disorder, and electronic properties were studied for the first time on large orientated single crystal. In the SrCoO{sub 2.5+{delta}} system, after structural and electronic characterisation of the end phases, we studied the real structure of the brownmillerite SrCoO{sub 2.5} phase using single crystal. Moreover, we investigated structural and magnetic evolution upon red ox cycle using X-ray diffraction on 6 times twinned single crystal and in situ neutron powder diffraction. Two intermediate SrCoO{sub 2.75} and SrCoO{sub 2.82} phases have been observed. The reaction on single crystal has evidenced the evolution of domain structure. For the La{sub 2}CoO{sub 4+{delta}} system, we synthesised a large variety of single crystal with stoichiometry {delta} 0.0, 0.09, 0.12, 0.16, 0.20 and 0.25. Using single crystal X-ray and neutron diffraction, we showed a disorder-order transition of the apical and interstitial oxygen for the higher {delta} values. (author)

Pb solubility of the high-temperature superconducting phase Bi2Sr2Ca2Cu3O10+d

International Nuclear Information System (INIS)

Kaesche, S.; Majewski, P.; Aldinger, F.

1994-01-01

For the nominal composition of Bi 2.27x Pb x Sr 2 Ca 2 Cu 3 O 10+d the lead content was varied from x=0.05 to 0.45. The compositions were examined between 830 degrees C and 890 degrees C which is supposed to be the temperature range over which the so-called 2223 phase (Bi 2 Sr 2 Ca 2 Cu 3 O 10+d ) is stable. Only compositions between x=0.18 to 0.36 could be synthesized in a single phase state. For x>0.36 a lead containing phase with a stoichiometry of Pb 4 (Sr,Ca) 5 CuO d is formed, for x 2 Sr 2 CaCu 2 O 8+d and cuprates are the equilibrium phases. The temperature range for the 2223 phase was found to be 830 degrees C to 890 degrees C but the 2223 phase has extremely varying cation ratios over this temperature range. Former single phase 2223 samples turn to multi phase samples when annealed at slightly higher or lower temperatures. A decrease in the Pb solubility with increasing temperature was found for the 2223 phase

CO2-laser ablation of Bi-Sr-Ca-Cu oxide by millisecond pulse lengths

Science.gov (United States)

Meskoob, M.; Honda, T.; Safari, A.; Wachtman, J. B.; Danforth, S.; Wilkens, B. J.

1990-03-01

We have achieved ablation of Bi-Sr-Ca-Cu oxide from single targets of superconducting pellets by CO2-laser pulses of l ms length to grow superconducting thin films. Upon annealing, the 6000-Å thin films have a Tc (onset) of 90 K and zero resistance at 78 K. X-ray diffraction patterns indicate the growth of single-phase thin films. This technique allows growth of uniform single-phase superconducting thin films of lateral area greater than 1 cm2.

Time and dose-related changes in the thickness of pig skin after irradiation with single doses of 90Sr/90Y β-rays

International Nuclear Information System (INIS)

Rezvani, M.; Hamlet, R.; Hopewell, J.W.; Sieber, V.K.

1994-01-01

Time-related changes in pig skin thickness have been evaluated using a non-invasive ultrasound technique after exposure to a range of single doses of 90 Sr/ 90 Yr β-rays. The reduction in relative skin thickness developed in two distinct phases: the first was between 12 and 20 weeks postirradiation. No further changes were then seen until 52 weeks postirradiation when a second phase of skin thinning was observed. This was complete after 76 weeks and no further changes in relative skin thickness were seen in the maximum follow up period of 129 weeks. The timings of these phases of damage were independent of the radiation dose, however, the severity of both phases of radiation-induced skin thinning were dose related. (Author)

Constraints on Ca/Sr as a Proxy for Calcium in Forest Ecosystems

Science.gov (United States)

Hoff, C. J.; Hobbie, E. A.; Hallett, R.; Colpaert, J.; Bryce, J. G.

2004-05-01

Calcium is a key plant nutrient and important base cation in ecosystems. Our current efforts to quantify Ca cycling in ecosystems rely on indirect proxies, e.g., Ca/Sr or Sr isotopic systems (1). An important assumption in these applications is that the elemental ratio of calcium to strontium faithfully represents calcium cycling and that little fractionation occurs through biogeochemical and physiological processes. However, several researchers have reported variations in Ca/Sr, e.g. among different tree tissues (2) and during weathering processes (3), raising doubts about the suitability of the proxy. To address the question of reliability, we measured Ca/Sr values in a culture study in which Scots pines were grown at low or high nutrient supply rates (3% per day or 5% per day). Because mycorrhizal fungi are intimately involved in plant nutrient supply, plants were also grown either uncolonized or colonized with one of two different species of mycorrhizal fungi (Suillus luteus and Thelephora terrestris). Our preliminary results indicate that Ca/Sr values differ between high and low nutrient treatments, root and foliage, and mycorrhizal treatments. In individual seedlings, roots have lower Ca/Sr than foliage by absolute factors of 2-5. The magnitude of the effect is apparently determined by a combination of environmental factors including both the nutrient and mycorrhizal treatments. These results indicate that Ca and Sr are partitioned differently between nutrient and mycorrhizal treatments and between plant fractions despite the common nutrient broth and substrate. Thus, Ca/Sr values alone are not reliable tracers of Ca within an ecosystem because of partitioning of Ca and Sr during nutrient transport within the plant-mycorrhizal system. We are presently refining analytical techniques and conducting leachate experiments to improve the quantification of this Ca/Sr fractionation. We are also exploring the use of isotopic tracers to study calcium biogeochemical

Using 87Sr/86Sr ratios to investigate changes in stream chemistry during snowmelt in the Provo River, Utah, USA

Science.gov (United States)

Hale, C. A.; Carling, G. T.; Fernandez, D. P.; Nelson, S.; Aanderud, Z.; Tingey, D. G.; Dastrup, D.

2017-12-01

Water chemistry in mountain streams is variable during spring snowmelt as shallow groundwater flow paths are activated in the watershed, introducing solutes derived from soil water. Sr isotopes and other tracers can be used to differentiate waters that have interacted with soils and dust (shallow groundwater) and bedrock (deep groundwater). To investigate processes controlling water chemistry during snowmelt, we analyzed 87Sr/86Sr ratios, Sr and other trace element concentrations in bulk snowpack, dust, soil, soil water, ephemeral channels, and river water during snowmelt runoff in the upper Provo River watershed in northern Utah, USA, over four years (2014-2017). Strontium concentrations in the river averaged 20 ppb during base flow and decreased to 10 ppb during snowmelt runoff. 87Sr/86Sr ratios were around 0.717 during base flow and decreased to 0.715 in 2014 and 0.713 in 2015 and 2016 during snowmelt, trending towards less radiogenic values of mineral dust inputs in the Uinta Mountain soils. Ephemeral channels, representing shallow flow paths with soil water inputs, had Sr concentrations between 7-20 ppb and 87Sr/86Sr ratios between 0.713-0.716. Snowpack Sr concentrations were generally soils that contain accumulated dust deposits with a less radiogenic 87Sr/86Sr ratio. These results suggest that flow paths and atmospheric dust are important to consider when investigating variable solute loads in mountain streams.

Quasi-static crack tip fields in rate-sensitive FCC single crystals

Indian Academy of Sciences (India)

In this work, the effects of loading rate, material rate sensitivity and constraint level on quasi-static crack tip fields in a FCC single crystal are studied. ... Global General Motors R&D, India Science Lab, GM Technical Centre (India), Bangalore 560 066, India; Department of Mechanical Engineering, Indian Institute of Science, ...

Separation of 90Y from 90Sr by solvent extraction with ionizable crown ethers

International Nuclear Information System (INIS)

Wood, D.J.; Elshani, S.; Du, H.S.; Natale, N.R.; Wai, C.M.

1993-01-01

Sym-Dibenzo-16-crown-5-oxyacetic acid and its analogues are selective for the extraction of Y 3+ over Sr 2+ from aqueous solutions into chloroform. The selectivity and the pH range of extraction are influenced by the structure of the ligand. The size of the macrocyclic cavity, the tether length of the lariat, the attachment of alkyl functional groups to the lariat, and the identity of the ionizable group can affect selectivity and extraction efficiency. When the carboxylic acid at the terminal end of the lariat is replaced by a hydroxamic acid, the selectivity for Y 3+ over Sr 2+ is significantly increased. Using these ionizable crown ethers as extractants, 90 Y fractions of greater than 99.9% purity can be obtained in a single solvent extraction step from solutions of 90 Sr. 11 refs., 5 figs., 2 tabs

Evidence of three-body correlation functions in Rb+ and Sr2+ acetonitrile solutions

Science.gov (United States)

D'Angelo, P.; Pavel, N. V.

1999-09-01

The local structure of Sr2+ and Rb+ ions in acetonitrile has been investigated by x-ray absorption spectroscopy (XAS) and molecular dynamics simulations. The extended x-ray absorption fine structure above the Sr and Rb K edges has been interpreted in the framework of multiple scattering (MS) formalism and, for the first time, clear evidence of MS contributions has been found in noncomplexing ion solutions. Molecular dynamics has been used to generate the partial pair and triangular distribution functions from which model χ(k) signals have been constructed. The Sr2+ and Rb+ acetonitrile pair distribution functions show very sharp and well-defined first peaks indicating the presence of a well organized first solvation shell. Most of the linear acetonitrile molecules have been found to be distributed like hedgehog spines around the Sr2+ and Rb+ ions. The presence of three-body correlations has been singled out by the existence of well-defined peaks in the triangular configurations. Excellent agreement has been found between the theoretical and experimental data enforcing the reliability of the interatomic potentials used in the simulations. These results demonstrate the ability of the XAS technique in probing the higher-order correlation functions in solution.

Sr - an element shows the way - Applications of Sr isotopes for provenance, tracing and migration (Invited)

Science.gov (United States)

Prohaska, T.; Irrgeher, J.; Zitek, A.; Teschler Nicola, M.

2010-12-01

Strontium - named after the small Scottish town Strontian - as such is an element with little popularity. Firstly described by Martin Heinrich Klaproth in 1798, the metal is used in metallurgy to some extent whereas its compounds are interesting in glass industries, electronics and pyrotechnics. The element has chemical similarity to Ca and makes up 1/60 of the earth’s amount of the latter. Nonetheless, it is its isotopic composition which makes Sr so interesting for a large number of scientists. The natural composition of the four naturally occurring isotopes (84Sr, 86Sr 87Sr and 88Sr) varies in nature due to the radioactive decay of 87Rb to 87Sr. Thus, it was early recognized as geochronometer especially in Ca rich matrices. With increasing precision of applied methodology, the natural variation of the 87Sr/86Sr isotope ratio (analyzed at first mainly by thermal ionization mass spectrometry (TIMS)) became more and more popular in provenance studies. The natural variation of the ratio is mainly determined by the geological age and the original composition of the rock and can be used therefore as fingerprint of the local geology. The ratio is transferred with no significant fractionation via the water into plants and finally via the food chain into animal and human tissues (especially bones and teeth). As the element is chemically similar to Ca, it appears in most matrices. The use for provenance studies is supported by the fact that the long half life (4.8 x 1010 years) does not lead to an alteration during the time scales which are investigated (from recent samples to human or animal skeletal remains which date back up to 30.000 BC). The uniqueness of the system besides the natural variation is defined by the ubiquity in nature and the relatively high (and thus measurable) elemental concentration in most tissues. It was finally the advent of multiple collector inductively coupled plasma mass spectrometry (MC-ICP-MS) which augmented the number of applications

Epitaxial growth and thermodynamic stability of SrIrO3/SrTiO3 heterostructures

Science.gov (United States)

Groenendijk, D. J.; Manca, N.; Mattoni, G.; Kootstra, L.; Gariglio, S.; Huang, Y.; van Heumen, E.; Caviglia, A. D.

2016-07-01

Obtaining high-quality thin films of 5d transition metal oxides is essential to explore the exotic semimetallic and topological phases predicted to arise from the combination of strong electron correlations and spin-orbit coupling. Here, we show that the transport properties of SrIrO3 thin films, grown by pulsed laser deposition, can be optimized by considering the effect of laser-induced modification of the SrIrO3 target surface. We further demonstrate that bare SrIrO3 thin films are subject to degradation in air and are highly sensitive to lithographic processing. A crystalline SrTiO3 cap layer deposited in-situ is effective in preserving the film quality, allowing us to measure metallic transport behavior in films with thicknesses down to 4 unit cells. In addition, the SrTiO3 encapsulation enables the fabrication of devices such as Hall bars without altering the film properties, allowing precise (magneto)transport measurements on micro- and nanoscale devices.

Fabrication of Schottky Junction Between Au and SrTiO3

Science.gov (United States)

Inoue, Akira; Izumisawa, Kei; Uwe, Hiromoto

2001-05-01

A Schottky junction with a high rectification ratio between Au and La-doped SrTiO3 has been fabricated using a simple surface treatment. Highly La-doped (5%) SrTiO3 single crystals are annealed in O2 atmosphere at about 1000°C for 1 h and etched in HNO3 for more than five min. The HNO3 etching is performed in a globe box containing N2 to prevent pollution from the air. After the treatment, Au is deposited on the SrTiO3 surface in a vacuum (˜ 10-7 Torr) with an e-gun evaporator. The current voltage characteristics of the junction have shown excellent rectification properties, although junctions using neither annealed nor etched SrTiO3 exhibit high leak current in reverse voltage. The rectification ratio of the junction at 1 V is more than six orders of magnitude and there is no hysteresis in the current voltage spectra. The logarithm of the current is linear with the forward bias voltage. The ideal factor of the junction is estimated to be about 1.68. These results suggest that, if prevented from being pollution by the air, a good Schottky junction can be obtained by easy processes such as annealing in oxygen atmosphere and surface etching with acid.

137Cs and 90Sr in dairy and farm milk in Finnish Lapland 1960-2000

International Nuclear Information System (INIS)

Kostiainen, E.; Rissanen, K.

2003-01-01

The decrease rates of 90 Sr and 137 Cs in milk were studied in the years following the atmospheric nuclear weapon testings and after the Chernobyl accident in 1986. The highest 90 Sr and 137 Cs concentrations in the 1960's in Finnish milk were recorded in Lapland even though the deposition of 90 Sr and 137 Cs did not significantly differ between other localities in Finland, and they were not greater in northern Finland. This was mainly due to the high proportion of peat soils and nutrient deficiency of the pastures in Lapland. 137 Cs deposition after the Chernobyl accident in 1986 in Lapland was less than 1 kBq m-2, and 90 Sr deposition was so low that there was no detectable increase in the 90 Sr concentration in milk. The ecological half-lives were estimated for the decrease in the concentrations of 137 Cs and 90 Sr after the end of nuclear weapon testings period and the Chernobyl fallout during short and longer time intervals. (orig.)

Strain-mediated magnetic response in La0.67Sr0.33MnO3/SrTiO3/La0.67Sr0.33MnO3/BaTiO3 structure

Science.gov (United States)

Swain, Anupama; Komatsu, Katsuyoshi; Itoh, Mitsuru; Taniyama, Tomoyasu; Gorige, Venkataiah

2018-05-01

Electric field controlled magnetism is an exciting area of condensed matter physics to explore the device applications at ultra-low power consumption compared to the conventional current controlled or magnetic field controlled devices. In this study, an attempt was made to demonstrate electric field controlled magnetoresistance (MR) in a tri-layer structure consisting of La0.67Sr0.33MnO3 (LSMO) (40 nm)/SrTiO3 (10 nm)/LSMO (10 nm) grown on a 500-μm-thick BaTiO3 (001) (BTO) single crystal substrate by pulsed laser deposition technique. Epitaxial growth of the trilayer structure was confirmed by x-ray diffraction measurements. Jumps observed in the temperature-dependent magnetization curve at around the structural phase transitions of BTO ensure the strain-mediated magnetoelectric coupling between LSMO and BTO layers. A significant change in MR of this structure in applied electric fields does not show any polarity dependence. The findings are related to the lattice strain-mediated magnetoelectric coupling in ferromagnetic LSMO/ferroelectric BTO heterostructures.

87Sr/86Sr ratios in permo-carboniferous sea water from the analyses of well-preserved brachiopod shells

International Nuclear Information System (INIS)

Popp, B.N.; Anderson, T.F.

1986-01-01

Sr isotopic analyses of well-preserved portions of Permo-Carboniferous brachiopods distributed globally confirm the general shape of the Sr isotope age curve established by previous workers for this time interval. There is little variation between the SR isotopic composition of unaltered portions of brachiopods and that of portions of the same shell interpreted to be diagenetically altered (based on cathodoluminescence, elemental, and stable isotopic data). However, the Sr isotopic composition in diagenetically altered micritic matrix adjacent to the shell is more radiogenic. The Sr isotopic composition in the unaltered portions of calcitic megafossils has potential as a stratigraphic tool. (author)

Tracking seasonal subglacial drainage evolution of alpine glaciers using radiogenic Nd and Sr isotope systematics: Lemon Creek Glacier, Alaska

Science.gov (United States)

Clinger, A. E.; Aciego, S.; Stevenson, E. I.; Arendt, C. A.

2014-12-01

The transport pathways of water beneath a glacier are subject to change as melt seasons progress due to variability in the balance between basal water pressure and water flux. Subglacial hydrology has been well studied, but the understanding of spatial distribution is less well constrained. Whereas radiogenic isotopic tracers have been traditionally used as proxies to track spatial variability and weathering rates in fluvial and riverine systems, these techniques have yet to be applied extensively to the subglacial environment and may help resolve ambiguity in subglacial hydrology. Research has shown the 143Nd/144Nd values can reflect variation in source provenance processes due to variations in the age of the continental crust. Correlating the 143Nd/144Nd with other radiogenic isotope systematics such as strontium (87Sr/86Sr) provides important constraints on the role of congruent and incongruent weathering processes. Our study presents the application of Nd and Sr systematics using isotopic ratios to the suspended load of subglacial meltwater collected over a single melt season at Lemon Creek Glacier, USA (LCG). The time-series data show an average ɛNd ~ -6.83, indicating a young bedrock (~60 MYA). Isotopic variation helps track the seasonal expansion of the subglacial meltwater channels and subsequent return to early season conditions due to the parabolic trend towards less radiogenic Nd in June and towards more radiogenic Nd beginning in mid-August. However, the high variability in July and early August may reflect a mixture of source as the channels diverge and derive sediment from differently aged lithologies. We find a poor correlation between 143Nd/144Nd and 87Sr/86Sr (R2= 0.38) along with a slight trend towards more radiogenic 87Sr/86Sr values with time ((R2= 0.49). This may indicate that, even as the residence time decreases over the melt season, the LCG subglacial system is relatively stable and that the bedrock is congruently weathered. Our study

Automated Speech Rate Measurement in Dysarthria

Science.gov (United States)

Martens, Heidi; Dekens, Tomas; Van Nuffelen, Gwen; Latacz, Lukas; Verhelst, Werner; De Bodt, Marc

2015-01-01

Purpose: In this study, a new algorithm for automated determination of speech rate (SR) in dysarthric speech is evaluated. We investigated how reliably the algorithm calculates the SR of dysarthric speech samples when compared with calculation performed by speech-language pathologists. Method: The new algorithm was trained and tested using Dutch…

Comparative study of pinning and creep in Tl2Ba2CaCu2O8 and Bi2Sr2CaCu2O8 single crystals

International Nuclear Information System (INIS)

Oussena, M.; Porter, S.; Volkozub, A.V.; de Groot, P.A.J.; Lanchester, P.C.; Ogborne, D.; Weller, M.T.; Balakrishnan, G.; Paul, D.M.

1993-01-01

We have compared the pinning and creep in two identically shaped single crystals, Tl 2 Ba 2 CaCu 2 O 8 (Tl 2:2:1:2) and Bi 2 Sr 2 CaCu 2 O 8 (Bi 2:2:1:2) using magnetometry. The critical current density, J c , deduced from the M-H hysteresis loops is found to be the highest in Bi 2:2:1:2 at low temperatures (T c , in this temperature range, is similar for both crystals. At higher temperatures, J c is found to decrease more rapidly with magnetic field in Bi 2:2:1:2 than in Tl 2:2:1:2. The critical current also decreases more quickly with temperature in Bi 2:2:1:2 leading to a vanishing J c at temperatures lower than in the case of Tl 2:2:1:2. I-V characteristic curves have been obtained from measurements of magnetic-sweep-rate dependencies of the hysteresis loops. We have found that the characteristic temperature at which flux motion becomes important is significantly higher in Tl 2:2:1:2 than in Bi 2:2:1:2

Spin dynamics in the single-ion magnet [Er(W5O18) 2 ] 9 -

Science.gov (United States)

Mariani, M.; Borsa, F.; Graf, M. J.; Sanna, S.; Filibian, M.; Orlando, T.; Sabareesh, K. P. V.; Cardona-Serra, S.; Coronado, E.; Lascialfari, A.

2018-04-01

In this work we present a detailed NMR and μ+SR investigation of the spin dynamics in the new hydrated sodium salt containing the single-ion magnet [Er(W5O18) 2 ] 9 -. The 1HNMR absorption spectra at various applied magnetic fields present a line broadening on decreasing temperature which indicates a progressive spin freezing of the single-molecule magnetic moments. The onset of quasistatic local magnetic fields, due to spin freezing, is observed also in the muon relaxation curves at low temperature. Both techniques yield a local field distribution of the order of 0.1-0.2 T, which appears to be of dipolar origin. On decreasing the temperature, a gradual loss of the 1HNMR signal intensity is observed, a phenomenon known as wipe-out effect. The effect is analyzed quantitatively on the basis of a simple model which relies on the enhancement of the NMR spin-spin, T2-1, relaxation rate due to the slowing down of the magnetic fluctuations. Measurements of spin-lattice relaxation rate T1-1 for 1HNMR and of the muon longitudinal relaxation rate λ show an increase as the temperature is lowered. However, while for the NMR case the signal is lost before reaching the very slow fluctuation region, the muon spin-lattice relaxation λ can be followed until very low temperatures and the characteristic maximum, reached when the electronic spin fluctuation frequency becomes of the order of the muon Larmor frequency, can be observed. At high temperatures, the data can be well reproduced with a simple model based on a single correlation time τ =τ0exp (Δ /T ) for the magnetic fluctuations. However, to fit the relaxation data for both NMR and μ+SR over the whole temperature and magnetic field range, one has to use a more detailed model that takes into account spin-phonon transitions among the E r3 + magnetic sublevels. A good agreement for both proton NMR and μ+SR relaxation is obtained, which confirms the validity of the energy level scheme previously calculated from an

Community-Level Characteristics Associated With Variation in Rates of Homelessness Among Families and Single Adults

Science.gov (United States)

Fargo, Jamison D.; Munley, Ellen A.; Byrne, Thomas H.; Montgomery, Ann Elizabeth; Culhane, Dennis P.

2013-01-01

Objectives. We modeled rates of family and single-adult homelessness in the United States in metropolitan and nonmetropolitan regions and as a function of community-level demographic, behavioral, health, economic, and safety net characteristics. Methods. We entered community-level characteristics and US Department of Housing and Urban Development point-in-time counts for a single night in January 2009 into separate mixed-effects statistical analyses that modeled homelessness rates for 4 subpopulations: families and single adults in metropolitan and nonmetropolitan regions. Results. Community-level factors accounted for 25% to 50% of the variance in homelessness rates across models. In metropolitan regions, alcohol consumption, social support, and several economic indicators were uniquely associated with family homelessness, and drug use and homicide were uniquely associated with single-adult homelessness. In nonmetropolitan regions, life expectancy, religious adherence, unemployment, and rent burden were uniquely associated with family homelessness, and health care access, crime, several economic indicators, and receipt of Supplemental Security Income were uniquely associated with single-adult homelessness. Conclusions. Considering homeless families and single adults separately enabled more precise modeling of associations between homelessness rates and community-level characteristics, indicating targets for interventions to reduce homelessness among these subpopulations. PMID:24148057

Community-level characteristics associated with variation in rates of homelessness among families and single adults.

Science.gov (United States)

Fargo, Jamison D; Munley, Ellen A; Byrne, Thomas H; Montgomery, Ann Elizabeth; Culhane, Dennis P

2013-12-01

We modeled rates of family and single-adult homelessness in the United States in metropolitan and nonmetropolitan regions and as a function of community-level demographic, behavioral, health, economic, and safety net characteristics. We entered community-level characteristics and US Department of Housing and Urban Development point-in-time counts for a single night in January 2009 into separate mixed-effects statistical analyses that modeled homelessness rates for 4 subpopulations: families and single adults in metropolitan and nonmetropolitan regions. Community-level factors accounted for 25% to 50% of the variance in homelessness rates across models. In metropolitan regions, alcohol consumption, social support, and several economic indicators were uniquely associated with family homelessness, and drug use and homicide were uniquely associated with single-adult homelessness. In nonmetropolitan regions, life expectancy, religious adherence, unemployment, and rent burden were uniquely associated with family homelessness, and health care access, crime, several economic indicators, and receipt of Supplemental Security Income were uniquely associated with single-adult homelessness. Considering homeless families and single adults separately enabled more precise modeling of associations between homelessness rates and community-level characteristics, indicating targets for interventions to reduce homelessness among these subpopulations.

Templated Atom-Precise Galvanic Synthesis and Structure Elucidation of a [Ag 24 Au(SR) 18 ] − Nanocluster

KAUST Repository

Bootharaju, Megalamane Siddaramappa

2015-11-27

Synthesis of atom-precise alloy nanoclusters with uniform composition is challenging when the alloying atoms are similar in size (for example, Ag and Au). A galvanic exchange strategy has been devised to produce a compositionally uniform [Ag24Au(SR)18]- cluster (SR: thiolate) using a pure [Ag25(SR)18]- cluster as a template. Conversely, the direct synthesis of Ag24Au cluster leads to a mixture of [Ag25-xAux(SR)18]-, x=1-8. Mass spectrometry and crystallography of [Ag24Au(SR)18]- reveal the presence of the Au heteroatom at the Ag25 center, forming Ag24Au. The successful exchange of the central Ag of Ag25 with Au causes perturbations in the Ag25 crystal structure, which are reflected in the absorption, luminescence, and ambient stability of the particle. These properties are compared with those of Ag25 and Ag24Pd clusters with same ligand and structural framework, providing new insights into the modulation of cluster properties with dopants at the single-atom level.

Review of SR 97 performance assessment

International Nuclear Information System (INIS)

Glynn, P.D.

2000-01-01

This review has identified many technical problems in the SR 97 performance assessment. The general impression of this reviewer is that SKB has been disingenuous in its performance assessment effort. It has not cited important differences of opinion with its own views. Furthermore, there are many inconsistencies in the SR 97 report that all together leave the impression that there are many more uncertainties in the SR 97 performance assessment than SKB would perhaps care to admit. Additionally, despite SKB's statements to the contrary, many of the analyses conducted for the SR 97 performance assessment can be clearly shown not to have been based on 'conservative' assumptions. Finally, SKB has made little effort to consider possible coupling effects between their different scenarios in SR 97. This is a serious flaw in the SR 97 performance assessment. The comments in this review should not be taken to imply that the KBS-3 nuclear waste disposal method will not be able to meet the safety and radiation protection requirements which SKI and SSI have specified in recent years. Instead, my conclusion is simply that the SR 97 performance assessment of the KBS-3 method would have been more believable had it been based on a forthright and comprehensive discussion of facts, uncertainties and opinions, and on a more conservative choice of assumptions. As it stands, the SR 97 performance assessment is not very credible

Apollo 17 'melt sheet': chemistry, age and Rb/Sr systematics

Energy Technology Data Exchange (ETDEWEB)

Winzer, S R [Martin Marietta Labs., Baltimore, Md. (USA); Nava, D F; Schuhmann, S; Philpotts, J A [National Aeronautics and Space Administration, Greenbelt, Md. (USA). Goddard Space Flight Center; Schuhmann, P J; Lum, R K.L.; Lindstrom, M M; Lindstrom, D J [Maryland Univ., College Park (USA)

1977-01-01

Major, minor and trace element compositions, age data and Rb/Sr systematics of Apollo 17 boulders have been compiled, and additional analyses performed on a norite breccia clast (77215) included in the Apollo 17, Station 7 boulder. The Apollo 17 boulders are found to be identical or nearly so in major, minor and trace element composition, suggesting that they all originated as an impact melt analogous to melt sheets found in larger terrestrial craters. The matrix dates (/sup 40/Ar//sup 39/Ar) and Rb/Sr systematics available suggest that this impact melt formed by a single impact about 4 b.y. ago. This impact excavated, shocked, brecciated and melted norites, norite cumulates and possibly anorthositic gabbros and dunites about 4.4 b.y. old. The impact was likely a major one, possibly the Serenitatis basin-forming event.

87Sr/86Sr isotopes in grapes of different cultivars: A geochemical tool for geographic traceability of agriculture products.

Science.gov (United States)

Tescione, Ines; Marchionni, Sara; Casalini, Martina; Vignozzi, Nadia; Mattei, Massimo; Conticelli, Sandro

2018-08-30

87 Sr/ 86 Sr was determined on fresh red and white grapes, soils and rocks from three selected vineyards to verify the isotopic relationships between the fruit of the vine and geologic substrata of vineyards. 87 Sr/ 86 Sr were determined on sampled grapes of four different harvest years and different grape varieties, on bioavailable fraction of soils, on whole soils, and on bedrocks from the geo-pedological substratum of the vineyards. The vineyards chosen for the experimental works belong to an organic farming winery and thus cultivation procedures were strictly controlled. Grapes were sampled during the harvests of four different but consecutive years with 87 Sr/ 86 Sr that does not change reflecting the values of the soil bioavailable fraction. No variations among grapes from different vine cultivars were observed. A strict isotope relationship with soil bio-available fraction was observed. These findings demonstrate the reliability of 87 Sr/ 86 Sr, even at a very small scale, for food products geographic origin assessment. Copyright © 2018 Elsevier Ltd. All rights reserved.

Therapeutic result of radioactive nuclide 90Sr/90Y treatment in patients with benign prostatic hypertrophy (BPH)

International Nuclear Information System (INIS)

Chen Hanchao; Li Yuying

2008-01-01

Objective: To study the effect of radioactive nuclide 90 Sr/ 90 Y treatment in patients with benign prostatic hypertrophy (BPH). Methods: Sixty patients with BPH were treated with a course of transurethral radioactive nuclide 90 Sr/ 90 Y therapy. Results: The severity of BPH was assessed with four parameters: maximal flow rate (MFR), volume of residual urine (VRU), international prostatic symptom score (IPSS) and volume (size) of prostate. In this series, the total effective rate was 93.33% with no treatment- related mortality. Favorable changes of the parameters after a course of radioactive nuclide therapy were significant. Conclusion: Radioactive nuclide 90 Sr/ 90 Y therapy for patients with BPH was safe, easily performed and quite effective. This procedure is worth popularizing in appropriate patients. (authors)

Sr-89 therapy: Strontium kinetics in disseminated carcinoma of the prostate

International Nuclear Information System (INIS)

Blake, G.M.; Zivanovic, M.A.; McEwan, A.J.; Ackery, D.M.

1986-01-01

Strontium kinetics were investigated in a group of 14 patients receiving 89 Sr palliation for metastatic bone disease secondary to prostatic carcinoma. Using 85 Sr as a tracer, total body strontium retention R(t) was monitored for a 3 month period following 89 Sr administration, and at 90 days was found to vary from 11% to 88% and to correlate closely with the fraction of the skeleton showing scintigraphic evidence of osteoblastic metastatic involvement. Strontium renal plasma clearance varied from 1.6l/ day to 11.6l/day, and in nine patients was significantly reduced compared with values found in healthy adult men, probably due to increased renal tubular reabsorption associated with the disturbance of calcium homoeostasis. Renal clearance rate was the principal factor determining R(t) for t 30 (t/30) -b , with R 30 and b showing the close correlation expected from the effect of R(t) on strontium recycling. The correction of the data for this effect to determine the true skeletal release rate is described. Measurement of localized strontium turnover in individual metastatic deposits from whole body profiles and scintigraphic images gave retention curves that typically rose to a plateau by 10 days after therapy, and then decreased very slowly. In contrast, retention curves for adjacent normal trabecular bone showed more rapid turnover, peaking at 1 day and subsequently decreasing following a t -0.2 power law function. The changes in strontium kinetics found in metastatic bone disease are favourable to the objectives of 89 Sr therapy. (orig.)

Hydrologic controls on radiogenic Sr in meltwater from an alpine glacier system: Athabasca Glacier, Canada

International Nuclear Information System (INIS)

Arendt, C.A.; Stevenson, E.I.; Aciego, S.M.

2016-01-01

Filtered subglacial meltwater samples were collected daily during the onset of melt (May) and peak melt (July) over the 2011 melt season at the Athabasca Glacier (Alberta, Canada) and analyzed for strontium-87/strontium-86 ("8"7Sr/"8"6Sr) isotopic composition to infer the evolution of subglacial weathering processes. Both the underlying bedrock composition and subglacial water–rock interaction time are the primary influences on meltwater "8"7Sr/"8"6Sr. The Athabasca Glacier is situated atop Middle Cambrian carbonate bedrock that also contains silicate minerals. The length of time that subglacial meltwater interacts with the underlying bedrock and substrate is a predominant determining factor in solute concentration. Over the course of the melt season, increasing trends in Ca/K and Ca/Mg correspond to overall decreasing trends in "8"7Sr/"8"6Sr, which indicate a shift in weathering processes from the presence of silicate weathering to primarily carbonate weathering. Early in the melt season, rates of carbonate dissolution slow as meltwater approaches saturation with respect to calcite and dolomite, corresponding to an increase in silicate weathering that includes Sr-rich silicate minerals, and an increase in meltwater "8"7Sr/"8"6Sr. However, carbonate minerals are preferentially weathered in unsaturated waters. During the warmest part of a melt season the discharged meltwater is under saturated, causing an increase in carbonate weathering and a decrease in the radiogenic Sr signal. Likewise, larger fraction contributions of meltwater from glacial ice corresponds to lower "8"7Sr/"8"6Sr values, as the meltwater has lower water–rock interaction times in the subglacial system. These results indicate that although weathering of Sr-containing silicate minerals occurs in carbonate dominated glaciated terrains, the continual contribution of new meltwater permits the carbonate weathering signal to dominate. - Highlights: • Glacial meltwater "8"7Sr/"8"6Sr used to

Development of 87Sr/86Sr maps as targeted strategy to support wine quality.

Science.gov (United States)

Durante, Caterina; Bertacchini, Lucia; Cocchi, Marina; Manzini, Daniela; Marchetti, Andrea; Rossi, Maria Cecilia; Sighinolfi, Simona; Tassi, Lorenzo

2018-07-30

This study summarizes the results obtained from a systematic and long-term project aimed at the development of tools to assess the provenance of food in the oenological sector. In particular, 87 Sr/ 86 Sr isotope ratios were measured on statistically representative set of soils, vine branches and wines sampled in the production district of Modena, worldwide known for the Lambrusco wines production. The obtained data were used to build strontium isotopic maps able to objectively support the Lambrusco PDO wines origin as well as other products of the Modena district. Finally, a strong relationship was found between the 87 Sr/ 86 Sr isotope ratios of soils and vine branches on a large scale, highlighting and confirming once more the idea that plants can also represent an optimal sampling device to support geographical traceability. Copyright © 2018 Elsevier Ltd. All rights reserved.

Single crystal growth of high-temperature superconductor Bi2.1Sr1.9Ca1.0Cu2.0AlyOx

International Nuclear Information System (INIS)

Gu, G.D.; Lin, Z.W.

2000-01-01

The effect of Al doping on the crystal growth of Bi-2212 was studied by a floating zone method. The results show that the planar solid-liquid interface breaks down into a cellular growth front while increasing Al doping in the rods of Bi 2.1 Sr 1.9 Ca 1.0 Cu 2.0 Al y O x . The size of the single crystals decreases with the increase in Al doping. The solubility limit for Al or the maximum Cu-site substitution by Al in the Bi-2212 crystals is less than y = 0.01. The majority of nominal Al doping in the rods forms an Al-rich phase in the grain boundaries of the single crystals. The superconductivity of as-grown Al-doped crystals decreases progressively with increasing Al doping in the rods, however, the T c for annealed Al-doped crystals does not change with increasing Al doping in the rods. The unchanged T c for annealed Al-doped Bi-2212 crystals either suggests that a small amount of Al substitution in the Cu site does not cause T c to drop significantly, or indicates that Al only enters the Bi-2212 crystals as an impurity, but does not substitute at the Cu site in the Bi-2212 crystals. (author)

Comparing Pt/SrTiO3 to Rh/SrTiO3 for hydrogen photocatalytic production from ethanol

KAUST Repository

Wahab, A. K.; Odedairo, T.; Labis, J.; Hedhili, Mohamed N.; Delavar, A.; Idriss, H.

2013-01-01

Photocatalytic hydrogen production from ethanol as an example of biofuel is studied over 0.5 wt% Rh/SrTiO3 and 0.5 wt% Pt/SrTiO3 perovskite materials. The rate of hydrogen production, rH2, over Pt/SrTiO3 is found to be far higher than that observed over Rh/SrTiO3 (4 × 10−6 mol of H2 g catal. −1 min−1 (1.1 × 10−6 mol of H2 m catal. −2 min−1) compared to 0.7 × 10−6 mol of H2 g catal. −1 min−1 (5.5 × 10−8 mol of H2 m catal. −2 min−1), respectively, under UV excitation with a flux equivalent to that from the sun light (ca. 1 mW cm−2). Analyses of the XPS Rh3d and XPS Pt4f indicate that Rh is mainly present in its ionic form (Rh3+) while Pt is mainly present in its metallic form (Pt0). A fraction of the non-metallic state of Rh in the catalyst persisted even after argon ion sputtering. The tendency of Rh to be oxidized compared to Pt might be the reason behind the lower activity of the former compared to the later. On the contrary, a larger amount of methane are formed on the Rh containing catalyst compared to that observed on the Pt containing catalyst due to the capacity of Rh to break the carbon–carbon bond of the organic compound.

Comparing Pt/SrTiO3 to Rh/SrTiO3 for hydrogen photocatalytic production from ethanol

KAUST Repository

Wahab, A. K.

2013-08-13

Photocatalytic hydrogen production from ethanol as an example of biofuel is studied over 0.5 wt% Rh/SrTiO3 and 0.5 wt% Pt/SrTiO3 perovskite materials. The rate of hydrogen production, rH2, over Pt/SrTiO3 is found to be far higher than that observed over Rh/SrTiO3 (4 × 10−6 mol of H2 g catal. −1 min−1 (1.1 × 10−6 mol of H2 m catal. −2 min−1) compared to 0.7 × 10−6 mol of H2 g catal. −1 min−1 (5.5 × 10−8 mol of H2 m catal. −2 min−1), respectively, under UV excitation with a flux equivalent to that from the sun light (ca. 1 mW cm−2). Analyses of the XPS Rh3d and XPS Pt4f indicate that Rh is mainly present in its ionic form (Rh3+) while Pt is mainly present in its metallic form (Pt0). A fraction of the non-metallic state of Rh in the catalyst persisted even after argon ion sputtering. The tendency of Rh to be oxidized compared to Pt might be the reason behind the lower activity of the former compared to the later. On the contrary, a larger amount of methane are formed on the Rh containing catalyst compared to that observed on the Pt containing catalyst due to the capacity of Rh to break the carbon–carbon bond of the organic compound.

Red electroluminescent process excited by hot holes in SrGa2S4:Ce, Mn thin film

International Nuclear Information System (INIS)

Tanaka, Katsu; Okamoto, Shinji

2009-01-01

This paper reports the first observation of red electroluminescence (EL) in SrGa 2 S 4 :Ce, Mn thin film. The EL spectrum consists of single broad emission band having a peak wavelength of 665 nm. The dominant EL decay time was 31 μs. The relationship between the applied voltage and the EL waveform was measured in single insulating thin film electroluminescent (TFEL) devices. An asymmetric EL waveform was observed in SrGa 2 S 4 :Ce, Mn TFEL devices under a rectangular applied voltage. The polarity of the EL waveform in these devices was different from the waveform in manganese-activated zinc sulfide ZnS:Mn devices. This indicates that hot holes excite the Mn 2+ ions to cause the red EL.

Promoting Photocatalytic Overall Water Splitting by Controlled Magnesium Incorporation in SrTiO3 Photocatalysts.

Science.gov (United States)

Han, Kai; Lin, Yen-Chun; Yang, Chia-Min; Jong, Ronald; Mul, Guido; Mei, Bastian

2017-11-23

SrTiO 3 is a well-known photocatalyst inducing overall water splitting when exposed to UV irradiation of wavelengths water-splitting efficiency of the Mg:SrTiO x composites is up to 20 times higher compared to SrTiO 3 containing similar catalytic nanoparticles, and an apparent quantum yield (AQY) of 10 % can be obtained in the wavelength range of 300-400 nm. Detailed characterization of the Mg:SrTiO x composites revealed that Mg is likely substituting the tetravalent Ti ion, leading to a favorable surface-space-charge layer. This originates from tuning of the donor density in the cubic SrTiO 3 structure by Mg incorporation and enables high oxygen-evolution rates. Nevertheless, interfacing with an appropriate hydrogen evolution catalyst is mandatory and non-trivial to obtain high-performance in water splitting. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Annual intake of 137Cs and 90Sr from ingestion of main foodstuffs in Taiwan

International Nuclear Information System (INIS)

Wang, Chih-Jung; Lai, Shu-Ying; Huang, Ching-Chung; Lin, Yu-ming

1996-01-01

The radioactivities of eight main foodstuffs were investigated during 1985-1994 to evaluate the annual intake from the ingestion of 137 Cs and 90 Sr for the residents of Taiwan. The evaluation of annual intake was based on the results of radiochemical analysis of 90 Sr and gamma-ray spectrometry of 137 Cs as well as annual consumption rates of those foodstuffs in Taiwan. The annual intake 90 Sr and 137 Cs per capita is 13 and 60 Bq, respectively. Among the eight foodstuffs, fruit contributed the most to the annual intake of 90 Sr, vegetable second, rice the third and egg the least. For 137 Cs, rice contributed the most, then fruit, meat the third and flour the least. Based on the new conversion factors from ICRP 60, the annual committed effective doses of Taiwanese due to the ingestion of radionuclides 90 Sr and 137 Cs were estimated to be 3.7 x 10 -7 and 7.8 x 10 -7 Sv, respectively. (author)

A High-Rate, Single-Crystal Model including Phase Transformations, Plastic Slip, and Twinning

Energy Technology Data Exchange (ETDEWEB)

Addessio, Francis L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Bronkhorst, Curt Allan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Bolme, Cynthia Anne [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Explosive Science and Shock Physics Division; Brown, Donald William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Materials Science and Technology Division; Cerreta, Ellen Kathleen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Materials Science and Technology Division; Lebensohn, Ricardo A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Materials Science and Technology Division; Lookman, Turab [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Luscher, Darby Jon [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Mayeur, Jason Rhea [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Theoretical Division; Morrow, Benjamin M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Materials Science and Technology Division; Rigg, Paulo A. [Washington State Univ., Pullman, WA (United States). Dept. of Physics. Inst. for Shock Physics

2016-08-09

An anisotropic, rate-­dependent, single-­crystal approach for modeling materials under the conditions of high strain rates and pressures is provided. The model includes the effects of large deformations, nonlinear elasticity, phase transformations, and plastic slip and twinning. It is envisioned that the model may be used to examine these coupled effects on the local deformation of materials that are subjected to ballistic impact or explosive loading. The model is formulated using a multiplicative decomposition of the deformation gradient. A plate impact experiment on a multi-­crystal sample of titanium was conducted. The particle velocities at the back surface of three crystal orientations relative to the direction of impact were measured. Molecular dynamics simulations were conducted to investigate the details of the high-­rate deformation and pursue issues related to the phase transformation for titanium. Simulations using the single crystal model were conducted and compared to the high-­rate experimental data for the impact loaded single crystals. The model was found to capture the features of the experiments.

Mineralogic Residence and Desorption Rates of Sorbed 90Sr in Contaminated Subsurface Sediments: Implications to Future Behavior and In-Ground Stability

International Nuclear Information System (INIS)

PIs: John M. Zachara; Jim P. McKinley; S. M. Heald; Chongxuan Liu; Peter C. Lichtner

2006-01-01

The project is investigating the adsorption/desorption process of 90Sr in coarse-textured pristine and contaminated Hanford sediment with the goal to define a generalized reaction-based model for use in reactive transport calculations. While it is known that sorbed 90Sr exists in an ion exchangeable state, the mass action relationships that control the solid-liquid distribution and the mineral phases responsible for adsorption have not been defined. Many coarse-textured Hanford sediment display significant sorptivity for 90Sr, but contain few if any fines that may harbor phyllosilicates with permanent negative charge and associated cation exchange capacity. Moreover, it is not known whether the adsorption-desorption process exhibits time dependence within context of transport, and if so, the causes for kinetic behavior

In-plane dissipation maxima and vortex-line distortions in the resistive transitions of oxygen-doped Bi2Sr2CaCu2O(8+delta) single crystals

Science.gov (United States)

Hsu, J. W. P.; Mitzi, D. B.; Kapitulnik, A.; Lee, Mark

1991-10-01

Measurements of the in-plane resistive transition of Bi2Sr2CaCu2O(8+delta) single crystals in perpendicular magnetic fields reveal that in oxygen-reduced samples a giant resistance maximum evolves with field. This is not seen in oxygenated samples with similar metallic normal resistivities. As the peak resistivity may exceed the normal resistivity, it cannot arise from ordinary vortex-motion dissipation. A model is proposed where the excess resistance results from nonrigid vortex motion coupling the out-of-plane dissipation to the in-plane resistance at temperatures where pinning effects are negligible.

Review of SR 97

International Nuclear Information System (INIS)

Voss, C.I.

2000-01-01

The safety analysis conducted by SKB for SR 97 is impressive in terms of both scale and content. In addition to an eventual solution to Sweden's nuclear waste isolation question, much general scientific knowledge of real value in other applications will be created as a by-product of SKB's efforts. This review focuses on those geoscience aspects of SR 97 that have the most important effects on radionuclide release from each barrier. Indeed, SR 97 elucidates the most important geoscience parameters that control releases from the near field and the far field; these comprise mainly the transport resistance parameter, and the sorption coefficients for each nuclide, the matrix diffusion coefficient, and the Darcy flux. The Main Report is the most important document in SR 97 inasmuch as it is the only one that brings together all of the supporting work to answer the question of safety. Unfortunately pervading the good supporting work done is the impression that the Main Report is not balanced, that it emphasizes optimistic aspects and downplays the negative. SKB specifies 3 main requirements to guarantee proper repository function: a non-oxidizing subsurface environment, temperatures less than 100 C, and a mechanically stable low-permeability buffer surrounding the canisters. The first and third requirements are not thoroughly proven by SKB. One source of near-field doubt stems from the consequences of combinations of scenarios in which several negative events are linked, while the effect of each scenario is mainly evaluated only independently in SR 97. More pertinently, disastrous breakdown of complex systems may occur due to a chain of linked failures. For example, in the glacial scenario: high ground-water flow (possible ablation of buffer and high fluid transport), change in ground-water chemistry (even the possibility of oxidizing conditions), new flow paths, significant changes in mechanical stress and possible motion along faults (which may also generate new flow

Effect of SrO on the electrical barrier formation and microstructure of TiO{sub 2} varistors

Energy Technology Data Exchange (ETDEWEB)

Delbrücke, Tiago, E-mail: tiagodt@gmail.com [Laboratory of Biomaterials & Advanced Ceramics, Engineering Materials Department, Federal University of Rio Grande do Sul, 91501-970, Porto Alegre, RS (Brazil); Pianaro, Sidnei A. [Interdisciplinary Laboratory of Ceramic Materials/LIMAC, Department of Materials Engineering, State University of Ponta Grossa, 84031-510, Ponta Grossa, PR (Brazil); Schmidt, Igor [Laboratory of Biomaterials & Advanced Ceramics, Engineering Materials Department, Federal University of Rio Grande do Sul, 91501-970, Porto Alegre, RS (Brazil); Cava, Sergio [Advanced Crystal Growth and Photonics, Technology Development Center, Federal University of Pelotas, 96010-900, Pelotas, RS (Brazil); Jurado, Jose R.; Sousa, Vânia C. [Laboratory of Biomaterials & Advanced Ceramics, Engineering Materials Department, Federal University of Rio Grande do Sul, 91501-970, Porto Alegre, RS (Brazil)

2016-12-01

TiO{sub 2}-based varistor materials with SrO dopants were prepared by the mechanical mixed oxides synthesis technique using conventional sintering at 1400 °C. I−V and microstructural characterization were performed. The composition range of 0.50–2.00 mol % SrO was studied and compared to pure TiO{sub 2}. Experimental evidence shows that small amounts of SrO improve the nonlinear properties of the samples significantly. Optimal varistor characteristics α = 5.50 and E{sub b} = 345 V/cm, were obtained with 1.00 mol % SrO-doped TiO{sub 2}. SrO in larger amounts causes the formation of precipitates of the SrTiO{sub 3} layer on the microstructure, being deleterious to the electrical properties. Therefore, dopants such as SrO or TiO{sub 2} play a special role in the morphology of the grain boundary and nonlinear response of these materials. An atomic defect model based on the double barrier Schottky type can be adopted to explain the formation of electrical barriers in TiO{sub 2} grain boundaries. - Highlights: • Training an effective potential barrier in the grain boundary, measured by electrical measurements on AC and DC. • Microstructure versus electrical properties. • Good properties getting varistor using a single dopant, forming a varistor binary system based on TiO{sub 2}.

A normalised seawater strontium isotope curve. Possible implications for Neoproterozoic-Cambrian weathering rates and the further oxygenation of the Earth

International Nuclear Information System (INIS)

Shields, G.A.

2007-01-01

The strontium isotope composition of seawater is strongly influenced on geological time scales by changes in the rates of continental weathering relative to ocean crust alteration. However, the potential of the seawater 87 Sr/ 86 Sr curve to trace globally integrated chemical weathering rates has not been fully realised because ocean 87 Sr/ 86 Sr is also influenced by the isotopic evolution of Sr sources to the ocean. A preliminary attempt is made here to normalise the seawater 87 Sr/ 86 Sr curve to plausible trends in the 87 Sr/ 86 Sr ratios of the three major Sr sources: carbonate dissolution, silicate weathering and submarine hydrothermal exchange. The normalised curve highlights the Neoproterozoic-Phanerozoic transition as a period of exceptionally high continental influence, indicating that this interval was characterised by a transient increase in global weathering rates and/or by the weathering of unusually radiogenic crustal rocks. Close correlation between the normalised 87 Sr/ 86 Sr curve, a published seawater δ 34 S curve and atmospheric pCO 2 models is used here to argue that elevated chemical weathering rates were a major contributing factor to the steep rise in seawater 87 Sr/ 86 Sr from 650 Ma to 500 Ma. Elevated weathering rates during the Neoproterozoic-Cambrian interval led to increased nutrient availability, organic burial and to the further oxygenation of Earth's surface environment. Use of normalised seawater 87 Sr/ 86 Sr curves will, it is hoped, help to improve future geochemical models of Earth System dynamics. (orig.)

Preparation of 90Sr-90Y generator

International Nuclear Information System (INIS)

Jin Xiaohai; Yu Haibin; Zhang Jinming; Zhang Peixin; Lin Qiongfang

1990-01-01

In recent years, 90 Y has been considered as one of the best radionuclides for tumor radioimmunotherapy when chelated to tumor-associated antibodies. This evaluation is based on the superior properties of this radionuclide (suitable half-life, pure β-ray emitter of intermediate energy, stable daughters, and suitable chemical properties) and because it is available as a radionuclide generator product by decay of its 28a parent 90 Sr. The experimental conditions of 90 Sr- 90 Y generator are described. The elution efficiency of 90 Sr- 90 Y generator reaches 98%. One of the most important problems is the 90 Sr contamination breakthrough from the generator. The level of 90 Sr contamination must be controlled to the clinical standard. The cation exchange resin 732 (100-150 mesh) was successfully used for the separation of 90 Y from 90 Sr. The method used by the authors provides a 90 Y-HAc solution which is very simple and safe for administration to the patients. 90 Y was separated from 90 Sr almost completely, the level of the 90 Sr contamination per 740 MBq 90 Y product was only 0.74 kBq. However the toxicity of 90 Sr is extremely high, the human life-time permissible dose is 74 kBq, then 740 MBq of 90 Y is allowed to be administrated to a patient for 50-100 times

Immune competence in 90Sr-exposed, adult thymectomized and antilymphocyteglobulin-treated CBA mice. Pt. 1

International Nuclear Information System (INIS)

Bierke, P.

1989-01-01

CBA mice subjected to either adult thymectomy, internal exposure to 90 Sr or antilymphocyteglobulin treatment separately, or to combinations of the three were tested for cellular immune competence using their reaction to allogenic skin grafts. Peripheral blood white cell counts did not reveal any obvious correlation between the degree of mononuclear cell depletion and the ability to accept grafts, suggesting that the particular treatments depleted specific fractions of mononuclear cells, differing in their extent of involvement in the rejection process. No single treatment alone induced a significant prolongation in the time elapsed before graft rejection. Adult thymectomy followed by appropriate antilymphocyteglobulin treatment induced severe lymphocytopenia and a profound suppression of the cell-mediate immune system, as evidenced by the acceptance of allogenic skin grafts. When applied to 90 Sr-preexposed mice the same treatment induced lifelong acceptance of grafts, indicating a similar, though weaker immunosuppressive impact of 90 Sr. Hence it was possible to significantly enhance immunosuppression in 90 Sr-exposed mice. This in vivo model should be useful when investigating the role of immunological responsiveness in radiation carcinogenesis. (orig.)

A first order approximation of the tumor absorbed dose prior to treatment with Sr-89

International Nuclear Information System (INIS)

Manetou, A.; Toubanakis, N.; Lyra, M.; Lymouris, G.

1994-01-01

A new technique developed for the estimation of the absorbed dose prior to treatment with Sr-89 is presented. This technique implies that patient undergoes bone scanning with Tc-99m-MDP, two days before the administration of Sr-89. A number of sequential quantitative images are to be obtained over the first 8 hours after the Tc-99m-MDP injection and data are used to derive St-89 time retention curve. For the development of this technique a simplified model for the kinetics of both Sr-89 and Tc-99m-MDP was assumed. Data on the time retention of the two radiopharmaceuticals for a compartment including bone surface and bone space of trabecular and cortical bone for normal adults were combined together. A linear relationship was derived between the time required for the same percentage uptake of the two radiopharmaceuticals after single injection. The absorbed dose in the principal metastases and normal bone, of the same type and volume with the metastases, for two patients who were treated with Sr-89 for metastasized prostatic carcinoma are reported. (authors)

Dose-response relationships for bone tumors in beagles exposed to 226Ra and 90Sr

International Nuclear Information System (INIS)

Raabe, O.G.; Parks, N.J.; Book, S.A.

1981-01-01

385 dogs were exposed to 90 Sr in food from mid-gestation to 540 days of age. 243 young adult dogs were given eight fortnightly injections of 226 Ra. Comparison was made with available mouse and human 226 Ra bone tumor data. The major findings were: a) the occurrence of bone tumor related deaths was much less for 90 Sr than for 226 Ra exposed dogs. b) RBE for bone tumors from 90 Sr-Y varied as a function of average dose rate to bone. c) people require 10 times as long as mice and 3.6 times as long as dogs to develop 226 Ra-induced bone tumors at a given skeletal dose rate. d) based on the results, a practical threshold for bone cancer from 226 Ra was estimated to exist at cumulative doses of about 50-110 rad for dogs, mice and people. (author)

Effect of seeding rate on grain quality of winter wheat

Directory of Open Access Journals (Sweden)

Veselinka Zecevic

2014-03-01

Full Text Available Planting density is important factor which influence yield and quality of wheat (Triticum aestivum L. For this reason, in scientific investigations is constantly investigated optimization of plant number per unit area. The objective of this study was to determine the influence of seeding rate in grain quality of winter wheat cultivars. The experiment was conducted with four winter wheat genotypes ('Ana Morava', 'Vizija', 'L-3027', and 'Perla' at the Small Grains Research Centre of Kragujevac, Serbia, in 3 yr at two seeding rates (SR1 = 500 and SR2 = 650 germinating seeds m-2. The 1000-kernel weight, Zeleny sedimentation, and wet gluten content in divergent wheat genotypes were investigated depending on the seeding rate and ecological factors. Significant differences in quality components were established between investigated seeding rates. The highest values of all investigated quality traits were established in SR2 variant when applied 650 seeds m-2. Genotypes reacted differently to seeding rate. 'Perla' in average had the highest mean sedimentation value (42.2 mL and wet gluten content (33.76% in SR2 variant and this cultivar responded the best to seeding rate. Significant differences for sedimentation value and wet gluten content were found among cultivars, years, seeding rate, and for all their interactions. Also, ANOVA for 1000-kernel weight showed highly significant differences among investigated varieties, seeding rate and growing seasons, but all their interactions were not significant. In all investigated genotypes, better quality was established in SR2 variant when applied 650 seeds m-2.

Microstructure and degradation performance of biodegradable Mg-Si-Sr implant alloys.

Science.gov (United States)

Gil-Santos, Andrea; Marco, Iñigo; Moelans, Nele; Hort, Norbert; Van der Biest, Omer

2017-02-01

In this work the microstructure and degradation behavior of several as-cast alloy compositions belonging to the Mg rich corner of the Mg-Si-Sr system are presented and related. The intermetallic phases are identified and analyzed describing the microstructure evolution during solidification. It is intended in this work to obtain insight in the behavior of the ternary alloys in in vitro tests and to analyze the degradation behavior of the alloys under physiologically relevant conditions. The as-cast specimens have been exposed to immersion tests, both mass loss (ML) and potentiodynamic polarization (PDP). The degradation rate (DR) have been assessed and correlated to microstructure features, impurity levels and alloy composition. The initial reactions resulted to be more severe while the degradation stabilizes with time. A higher DR is related with a high content of the Mg 17 Sr 2 phase and with the presence of coarse particles of the intermetallics Mg 2 Si, MgSiSr and MgSi 2 Sr. Specimens with a higher DR typically have higher levels of impurities and alloy contents. Copyright © 2016 Elsevier B.V. All rights reserved.

90Sr- 90Y and 89Sr beta radioactivity measurement in milk samples using a proportional counter

International Nuclear Information System (INIS)

Mananes, A.; Perez Santos, C.; Martinez Churiaque, F.

1987-01-01

A thin window glas flow proportional counter is used to measure the 90 Sr- 90 Y and 89 Sr beta radioactivity in milk samples. A chemical procedure is used to separate strontium-yttrium from the other radionuclides present in milk. A calculation of the total efficiency of the system is performed which includes an empirical estimation of the backscattering factor. The calibration of the whole process allows the determination of the 90 Sr activity within 10% relative error in spite of uncertainties in the recovery yields of strontium and yttrium. No 89 Sr activity has been detected, and the mean value obtained for the 90 Sr activity in nine milk samples of Cantabria is 0.115 Bq/1 with a minimum detectable activity of 0.0105 Bq. (author) 18 refs

Formation of Ruddlesden-Popper Faults and Their Effect on the Magnetic Properties in Pr0.5Sr0.5CoO3 Thin Films.

Science.gov (United States)

Jing, Hong-Mei; Cheng, Sheng; Mi, Shao-Bo; Lu, Lu; Liu, Ming; Cheng, Shao-Dong; Jia, Chun-Lin

2018-01-10

Epitaxial Pr 0.5 Sr 0.5 CoO 3 thin films have been grown on single-crystalline (La 0.289 Sr 0.712 )(Al 0.633 Ta 0.356 )O 3 (001) substrates by the pulsed laser deposition technique. The magnetic properties and microstructure of these films are investigated. It is found that Ruddlesden-Popper faults (RP faults) can be introduced in the films by changing the laser repetition rate. The segregation of Pr at the RP faults is characterized by atomic-resolution chemical mapping. The formation of the RP faults not only contributes to the epitaxial strain relaxation but also significantly decreases the ferromagnetic long-range order of the films, resulting in lower magnetizations than those of the fault-free films. Our results provide a strategy for tuning the magnetic properties of cobalt-based perovskite films by modifying the microstructure through the film growth process.

Atomic layer epitaxy of Ruddlesden-Popper SrO(SrTiO3)n films by means of metalorganic aerosol deposition

International Nuclear Information System (INIS)

Jungbauer, M.; Hühn, S.; Moshnyaga, V.; Egoavil, R.; Tan, H.; Verbeeck, J.; Van Tendeloo, G.

2014-01-01

We report an atomic layer epitaxial growth of Ruddlesden-Popper (RP) thin films of SrO(SrTiO 3 ) n (n = ∞, 2, 3, 4) by means of metalorganic aerosol deposition (MAD). The films are grown on SrTiO 3 (001) substrates by means of a sequential deposition of Sr-O/Ti-O 2 atomic monolayers, monitored in-situ by optical ellipsometry. X-ray diffraction and transmission electron microscopy (TEM) reveal the RP structure with n = 2–4 in accordance with the growth recipe. RP defects, observed by TEM in a good correlation with the in-situ ellipsometry, mainly result from the excess of SrO. Being maximal at the film/substrate interface, the SrO excess rapidly decreases and saturates after 5–6 repetitions of the SrO(SrTiO 3 ) 4 block at the level of 2.4%. This identifies the SrTiO 3 substrate surface as a source of RP defects under oxidizing conditions within MAD. Advantages and limitations of MAD as a solution-based and vacuum-free chemical deposition route were discussed in comparison with molecular beam epitaxy

Effect of additives on the orientation of magnetic Sr-ferrite powders in powder injection molded compacts

Energy Technology Data Exchange (ETDEWEB)

Cho, T.S. [Sangju National Unviersity, Sangju (Korea); Jeung, W.Y. [Korea Institute of Science and Technology, Seoul (Korea)

2001-03-01

The effect of additives on the orientation of magnetic Sr-ferrite powders has been studied during powder injection molding under applied magnetic field for fabricating multi=pole anisotropic sintered Sr-ferrite magnets. The orientation of the Sr-ferrite powders depends sensitively on the fluidity of powder-binder mixture, related to the binder additives and the injection molding temperature, and the magnetic field intensity. The orientation of Sr-ferrite powders is good for the compacts with stearic acid added in the binder system of paraffin wax/ carnauba wax/HDPE, but it is poor of the compacts with silane coupling agent added. The orientation of sr-ferrites higher than 80% is achieved at the following useful conditions; apparent viscosity lower than 2500 poise in 1000 sec {sup -1} shear rate and applied magnetic field higher than 4 kOe. (author). 15 refs., 1 tab., 6 figs.

Multiple dose study of the combined radiosensitizers Ro 03-8799 (pimonidazole) and SR 2508 (etanidazole)

International Nuclear Information System (INIS)

Bleehen, N.M.; Newman, H.F.; Maughan, T.S.; Workman, P.

1989-01-01

The hypoxic cell radiosensitizers Ro 03-8799 and SR 2508 have different clinical toxicities. The former produces an acute but transient central nervous system syndrome, whereas the latter produces cumulative peripheral neuropathy. Following single dose studies, an escalating multiple dose schedule using both drugs in combination showed no unexpected adverse reactions at lower doses. This study identifies the clinical tolerance and pharmacokinetics when doses in the region of the maximal tolerated dose are given to 26 patients receiving infusions of 0.75 g/m2 Ro 03-8799 and 2 g/m2 SR 2508 three times per week. At 15 doses, 3/4 patients experienced WHO grade 2 peripheral neuropathy, whereas at 12 doses 1/9 developed grade 2 and 6/9 developed grade 1 neuropathies. This represents a lower dose of SR 2508 than can be given alone suggesting that some interaction between the two drugs does exist in terms of chronic peripheral neurotoxicity. Pharmacokinetic studies show no adverse interactions between the two drugs and minimal inter-patient variation. From bivariate analysis, cumulative AUC for Ro 03-8799 has the most significant correlation with the development of peripheral neuropathy. Tumor drug concentrations normalized to the administered dose show mean values of 34 micrograms/g Ro 03-8799 and 76 micrograms/g SR 2508 30 minutes after infusion. These could be expected to produce a single dose sensitizer enhancement ratio of 1.5. The combination of the two sensitizers at the maximum tolerable dose may be expected to give an increased therapeutic efficacy over either drug alone

Single blastocyst transfer: The key to reduce multiple pregnancy rates without compromising the live birth rate

Directory of Open Access Journals (Sweden)

Uma M Sundhararaj

2017-01-01

Full Text Available Background: Historically, to achieve higher pregnancy rates, multiple embryos were transferred after an in-vitro fertilisation (IVF. However, this practice is being reassessed, because it leads to multiple pregnancies that is known to cause adverse maternal and fetal outcomes. Aim: To compare the pregnancy outcomes in fresh IVF or intracytoplasmic sperm injection (ICSI cycles among women undergoing elective single blastocyst transfer (eSBT vs. those undergoing double blastocyst transfer (DBT. Settings and Design: It is a retrospective data analysis of 582 patients undergoing fresh IVF/ICSI cycles performed from January 2012 to June 2015. Materials and Methods: Patients, who underwent IVF/ICSI and developed more than one blastocyst, were included in the study. Donor cycles were excluded from the study. All the embryos were cultured to blastocyst stage in sequential media followed by transfer of two blastocysts (DBT or eSBT and cryopreservation of the remaining. Statistical Analysis: Statistical analysis was performed using chi square test. Results: Out of 582 patients, in 149 patients one blastocyst was transferred and in 433 patients two blastocysts were transferred. There was no statistical difference in the biochemical pregnancy rate, clinical pregnancy rate and live birth rate in both the groups. Statistics demonstrated a significant drop in miscarriage rate in eSBT group. There was no incidence of twins in eSBT group, whereas twin birth rate per clinical pregnancy was 29.02% in DBT group. Conclusion: Single blastocyst transfer is an effective method to reduce the risk of multiple births without compromising the pregnancy outcomes. Given the promising potential of vitrification; the remaining blastocyst can be cryopreserved.

Sulfide and Oxide Heterostructures For the SrTiO3 Thin Film Growth on Si and Their Structural and Interfacial Stabilities

Science.gov (United States)

Yoo, Young‑Zo; Song, Jeong‑Hwan; Konishi, Yoshinori; Kawasaki, Masashi; Koinuma, Hideomi; Chikyow, Toyohiro

2006-03-01

Epitaxial SrTiO3 (STO) thin films with high electrical properties were grown on Si using ZnS single- and SrS/MnS hetero-buffer layers. STO films on both ZnS-buffered and SrS/MnS-buffered Si showed two growth orientations, (100) and (110). The temperature dependence of the growth orientation for STO films was different for the ZnS single-buffer layer in comparison with the SrS/MnS heterobuffer layers. (100) growth of STO films on SrS/MnS-buffered Si became dominant at high temperatures about 700 °C, while (100) growth of STO films on ZnS-buffered Si became dominant at a relatively low growth temperature of 550 °C. STO(100) films on ZnS-buffered and SrS/MnS-buffered Si showed lattice and domain matches for epitaxial relationships with [001]ZnS\\parallel[011]STO and SrS[001]\\parallel[011]STO, respectively via 45° in-plane rotation of STO films relative to both ZnS and SrS layers. The ZnS buffer layer contained many stacking faults because of the mismatch between ZnS and Si, however, those defects were terminated at the ZnS/STO interface. In contrast, the MnS buffer was very stable against stacking defect formation. Transmission electron microscopy measurements revealed the presence of a disordered region at the ZnS/Si and MnS/Si interfaces. Auger electron spectroscopy and transmission electron microscopy results showed that a good MnS/Si interface at the initial growth stage degraded to a SiS2-x-rich phase during MnS deposition and again into a SiO2-x-rich phase during STO deposition at the high growth temperature of 700 °C. It was also observed that STO on SrS/MnS-buffered Si showed a markedly high dielectric constant compared with that of STO on ZnS-buffered Si.

Peculiarities of Sr-90 migration in the environment

International Nuclear Information System (INIS)

Romanov, G.N.; Stukin, D.A.; Aleksakhin, R.M.

1991-01-01

The Eastern Urals radioactive track which formed as a result of the Kyshtym accident constituted a natural experimental base for studying the dynamics of Sr-90 behaviour and migration in the environment. Sr-90 behaviour in soil depends on the processes involved in its physical migration horizontally (water runoff, wind transport) and vertically (effective diffusion), on the intensity with which the physico-chemical forms of strontium change, and primarily on Sr-90 incorporation into the soil-absorptive complex. Over 30 years the effective diffusion processes led to downward displacement of Sr-90 in undisturbed soil to a depth of 30 to 50 cm. In 1988 84-94% of the Sr-90 was located in the 10 cm layer as against 90% in the 2 cm layer in the initial 1 or 2 years. The amount of Sr-90 in mobile forms in leached chernozem and grey forest soil hardly changed over time, amounting to between 76 and 90%. In the first 5-10 years Sr-90 surface water runoff was about 0.2% (and Sr-90 wind resuspension 0.1-1.0%) per year of the Sr-90 inventory per unit area. Due to Sr-90 loss from the top soil layer the water runoff and wind resuspension processes decreased exponentially, halving every 4 to 5 years. In most cases, Sr-90 transfer from soil to plants via the roots does not involve discrimination of Sr-90 with regard to calcium, and therefore the Sr-90 accumulation level in various species of natural and agricultural plants depends on their calcium requirements and the amount of exchangeable calcium in the soil. This made it possible to work out quantitative indices for forecasting Sr-90 accumulation in various species of plants for given types of soil. As Sr-90 moves through the trophic chains (including the agricultural one) we find - depending on whether two adjoining links discriminate against it or not as regards calcium - that some organisms reject it while others concentrate it. When restoring farming on the contaminated territory the fact that cattle discriminated against Sr

SrZnO nanostructures grown on templated Al2O3 substrates by pulsed laser deposition

Science.gov (United States)

Labis, Joselito P.; Alanazi, Anwar Q.; Albrithen, Hamad A.; El-Toni, Ahmed Mohamed; Hezam, Mahmoud; Elafifi, Hussein Elsayed; Abaza, Osama M.