Virtual peer-delivered memory intervention: a single-case experimental design in an adolescent with chronic memory impairment.

Science.gov (United States)

Cooper, Janine M; Lockett, Stephen; McIlroy, Alissandra; Gonzalez, Linda

2018-01-01

Children and adolescents with chronic memory impairment may develop coping strategies that enable functioning, yet these often remain undetectable using traditional psychometric measures. Personalized intervention studies that promote the use of such strategies designed specifically for use by this young cohort are scarce. To investigate the effect of a novel virtual reality peer-delivered memory intervention on the everyday functioning and well-being of SE, a 17-year-old female with a history of chronic verbal memory issues, impaired autobiographical event recall and elevated mood symptoms. A single-case ABA experimental design study was used to assess change. Following initial baseline assessment using objective neuropsychological and subjective functional questionnaires and intervention training, case SE used the intervention daily for 3 weeks before repeating key outcome measures. Using non-overlap of all pairs and qualitative feedback analysis, the results revealed a significant increase in event recall and self-reported positive changes to levels of everyday functioning. Supporting autobiographical event recall and prospective memory via a virtual peer-delivered intervention may lead to reduction in cognitive load, and benefit overall well-being and everyday functioning.

Evidence-Based Communication Practices for Children with Visual Impairments and Additional Disabilities: An Examination of Single-Subject Design Studies

Science.gov (United States)

Parker, Amy T.; Grimmett, Eric S.; Summers, Sharon

2008-01-01

This review examines practices for building effective communication strategies for children with visual impairments, including those with additional disabilities, that have been tested by single-subject design methodology. The authors found 30 studies that met the search criteria and grouped intervention strategies to align any evidence of the…

Optimum design of a Lanchester damper for a viscously damped single degree of freedom system subjected to inertial excitation

Science.gov (United States)

Bapat, V. A.; Prabhu, P.

1980-11-01

The problem of designing an optimum Lanchester damper for a viscously damped single degree of freedom system subjected to inertial harmonic excitation is investigated. Two criteria are used for optimizing the performance of the damper: (i) minimum motion transmissibility; (ii) minimum force transmissibility. Explicit expressions are developed for determining the absorber parameters.

Within-subject mediation analysis for experimental data in cognitive psychology and neuroscience.

Science.gov (United States)

Vuorre, Matti; Bolger, Niall

2017-12-15

Statistical mediation allows researchers to investigate potential causal effects of experimental manipulations through intervening variables. It is a powerful tool for assessing the presence and strength of postulated causal mechanisms. Although mediation is used in certain areas of psychology, it is rarely applied in cognitive psychology and neuroscience. One reason for the scarcity of applications is that these areas of psychology commonly employ within-subjects designs, and mediation models for within-subjects data are considerably more complicated than for between-subjects data. Here, we draw attention to the importance and ubiquity of mediational hypotheses in within-subjects designs, and we present a general and flexible software package for conducting Bayesian within-subjects mediation analyses in the R programming environment. We use experimental data from cognitive psychology to illustrate the benefits of within-subject mediation for theory testing and comparison.

The effect of a motor-based, social skills intervention for adolescents with high-functioning autism: two single-subject design cases.

Science.gov (United States)

Gutman, Sharon A; Raphael, Emily I; Ceder, Leila M; Khan, Arshi; Timp, Katherine M; Salvant, Sabrina

2010-12-01

The purpose of this study was to assess the effect of a motor-based, social skills intervention for two adolescents with high-functioning autism (HFA) using single-subject design. A description of the intervention is provided as a first step in the manualization process. The intervention was provided as a 7-week after-school program, once weekly to the paired participants. Intervention consisted of role-play methods in which motor behaviours were linked with their cognitive and emotional meanings. Baseline, intervention and 3-month probe data collection periods were carried out and then compared using visual inspection of graphed data, paired t-tests and a three-standard-deviation-band approach. Both participants displayed a statistically significant increase in targeted social skills behaviours from baseline to intervention and maintained this level at a 3-month post-intervention probe. These single-subject design cases illustrate that motor-based, social skills interventions may be effective for adolescents with HFA and warrant further testing. Copyright © 2010 John Wiley & Sons, Ltd.

Single Subject Research: Applications to Special Education

Science.gov (United States)

Cakiroglu, Orhan

2012-01-01

Single subject research is a scientific research methodology that is increasingly used in the field of special education. Therefore, understanding the unique characteristics of single subject research methodology is critical both for educators and practitioners. Certain characteristics make single subject research one of the most preferred…

Can Constraint Induced Movement Therapy Improve In-Hand Manipulation Skills: A Single Subject Design

Directory of Open Access Journals (Sweden)

Somaye Kavousipor

2012-04-01

Full Text Available Objectives: This study describes a single subject design (ABA that shows the effective use of constraint induced movement therapy in improvement of quality and performance of in-hand manipulation skills for a 10 year old boy and a 9 years old girl with hemiplegic cerebral palsy, as Dickerson (2007 showed it in arm movement and function. Methods: To determine the effectiveness of CIMT by the use of C-statistic analysis and visual analysis. Approach: The first step was to design a child friendly group activity and home based intervention program through occupation. The possible effectiveness of CIMT was evaluated by daily measurements and video recording of 6 sub skills of in-hand manipulation according to Pont category (2009 in defined activity. Results: For making the treatment more cost effective, families can produce a simple clinical setting at home and participate in their child treatment plan actively. Discussion: A client center intervention will facilitate the use and quality of fingers and hand motion. Also a group activity can motivate participants to participate more and better.

Analysis, Design, and Experimental Verification of A Synchronous Reference Frame Voltage Control for Single-Phase Inverters

DEFF Research Database (Denmark)

Monfared, Mohammad; Golestan, Saeed; Guerrero, Josep M.

2014-01-01

Control of three-phase power converters in the synchronous reference frame is now a mature and well developed research topic. However, for single-phase converters, it is not as well-established as three-phase applications. This paper deals with the design of a synchronous reference frame multi-lo...... on a frequency response approach is presented. Finally, the theoretical achievements are supported by experimental results.......-loop control strategy for single phase inverter-based islanded distributed generation (DG) systems. The proposed controller uses a synchronous reference frame PI (SRFPI) controller to regulate the instantaneous output voltage, a capacitor current shaping loop in the stationary reference frame to provide active...

Experimental design of a waste glass study

International Nuclear Information System (INIS)

Piepel, G.F.; Redgate, P.E.; Hrma, P.

1995-04-01

A Composition Variation Study (CVS) is being performed to support a future high-level waste glass plant at Hanford. A total of 147 glasses, covering a broad region of compositions melting at approximately 1150 degrees C, were tested in five statistically designed experimental phases. This paper focuses on the goals, strategies, and techniques used in designing the five phases. The overall strategy was to investigate glass compositions on the boundary and interior of an experimental region defined by single- component, multiple-component, and property constraints. Statistical optimal experimental design techniques were used to cover various subregions of the experimental region in each phase. Empirical mixture models for glass properties (as functions of glass composition) from previous phases wee used in designing subsequent CVS phases

Optimizing Within-Subject Experimental Designs for jICA of Multi-Channel ERP and fMRI

Science.gov (United States)

Mangalathu-Arumana, Jain; Liebenthal, Einat; Beardsley, Scott A.

2018-01-01

Joint independent component analysis (jICA) can be applied within subject for fusion of multi-channel event-related potentials (ERP) and functional magnetic resonance imaging (fMRI), to measure brain function at high spatiotemporal resolution (Mangalathu-Arumana et al., 2012). However, the impact of experimental design choices on jICA performance has not been systematically studied. Here, the sensitivity of jICA for recovering neural sources in individual data was evaluated as a function of imaging SNR, number of independent representations of the ERP/fMRI data, relationship between instantiations of the joint ERP/fMRI activity (linear, non-linear, uncoupled), and type of sources (varying parametrically and non-parametrically across representations of the data), using computer simulations. Neural sources were simulated with spatiotemporal and noise attributes derived from experimental data. The best performance, maximizing both cross-modal data fusion and the separation of brain sources, occurred with a moderate number of representations of the ERP/fMRI data (10–30), as in a mixed block/event related experimental design. Importantly, the type of relationship between instantiations of the ERP/fMRI activity, whether linear, non-linear or uncoupled, did not in itself impact jICA performance, and was accurately recovered in the common profiles (i.e., mixing coefficients). Thus, jICA provides an unbiased way to characterize the relationship between ERP and fMRI activity across brain regions, in individual data, rendering it potentially useful for characterizing pathological conditions in which neurovascular coupling is adversely affected. PMID:29410611

Evaluating statistical and clinical significance of intervention effects in single-case experimental designs: An SPSS method to analyze univariate data

NARCIS (Netherlands)

Maric, M.; de Haan, M.; Hogendoorn, S.M.; Wolters, L.H.; Huizenga, H.M.

2015-01-01

Single-case experimental designs are useful methods in clinical research practice to investigate individual client progress. Their proliferation might have been hampered by methodological challenges such as the difficulty applying existing statistical procedures. In this article, we describe a

Evaluating statistical and clinical significance of intervention effects in single-case experimental designs: an SPSS method to analyze univariate data

NARCIS (Netherlands)

Maric, Marija; de Haan, Else; Hogendoorn, Sanne M.; Wolters, Lidewij H.; Huizenga, Hilde M.

2015-01-01

Single-case experimental designs are useful methods in clinical research practice to investigate individual client progress. Their proliferation might have been hampered by methodological challenges such as the difficulty applying existing statistical procedures. In this article, we describe a

Experimental design techniques in statistical practice a practical software-based approach

CERN Document Server

Gardiner, W P

1998-01-01

Provides an introduction to the diverse subject area of experimental design, with many practical and applicable exercises to help the reader understand, present and analyse the data. The pragmatic approach offers technical training for use of designs and teaches statistical and non-statistical skills in design and analysis of project studies throughout science and industry. Provides an introduction to the diverse subject area of experimental design and includes practical and applicable exercises to help understand, present and analyse the data Offers technical training for use of designs and teaches statistical and non-statistical skills in design and analysis of project studies throughout science and industry Discusses one-factor designs and blocking designs, factorial experimental designs, Taguchi methods and response surface methods, among other topics.

Optimization of single-walled carbon nanotube solubility by noncovalent PEGylation using experimental design methods

Directory of Open Access Journals (Sweden)

Hadidi N

2011-04-01

Full Text Available Naghmeh Hadidi1, Farzad Kobarfard2, Nastaran Nafissi-Varcheh3, Reza Aboofazeli11Department of Pharmaceutics, 2Department of Pharmaceutical Chemistry, 3Department of Pharmaceutical Biotechnology, School of Pharmacy, Shaheed Beheshti University of Medical Sciences, Tehran, IranAbstract: In this study, noncovalent functionalization of single-walled carbon nanotubes (SWCNTs with phospholipid-polyethylene glycols (Pl-PEGs was performed to improve the solubility of SWCNTs in aqueous solution. Two kinds of PEG derivatives, ie, Pl-PEG 2000 and Pl-PEG 5000, were used for the PEGylation process. An experimental design technique (D-optimal design and second-order polynomial equations was applied to investigate the effect of variables on PEGylation and the solubility of SWCNTs. The type of PEG derivative was selected as a qualitative parameter, and the PEG/SWCNT weight ratio and sonication time were applied as quantitative variables for the experimental design. Optimization was performed for two responses, aqueous solubility and loading efficiency. The grafting of PEG to the carbon nanostructure was determined by thermogravimetric analysis, Raman spectroscopy, and scanning electron microscopy. Aqueous solubility and loading efficiency were determined by ultraviolet-visible spectrophotometry and measurement of free amine groups, respectively. Results showed that Pl-PEGs were grafted onto SWCNTs. Aqueous solubility of 0.84 mg/mL and loading efficiency of nearly 98% were achieved for the prepared Pl-PEG 5000-SWCNT conjugates. Evaluation of functionalized SWCNTs showed that our noncovalent functionalization protocol could considerably increase aqueous solubility, which is an essential criterion in the design of a carbon nanotube-based drug delivery system and its biodistribution.Keywords: phospholipid-PEG, D-optimal design, loading efficiency, Raman spectroscopy, scanning electron microscopy, theromogravimetric analysis, carbon nanotubes

Exposure-based cognitive behavioral therapy for irritable bowel syndrome. A single-case experimental design across 13 subjects.

Science.gov (United States)

Boersma, Katja; Ljótsson, Brjánn; Edebol-Carlman, Hanna; Schrooten, Martien; Linton, Steven J; Brummer, Robert J

2016-11-01

Irritable bowel syndrome (IBS) is a highly prevalent disorder with a significant impact on quality of life. The presence of psychological symptoms in IBS patients such as catastrophic worry and behavioral avoidance suggests the possible efficacy of cognitive behavioral interventions. Exposure-based cognitive behavioral therapy (CBT) has proven to be a promising approach but has only been investigated in a few studies and mainly via the Internet. Therefore, the aims of this study were to extend and replicate previous findings and to evaluate whether an individual, face-to-face, exposure-based CBT leads to improvement in gastrointestinal symptoms, pain catastrophizing, avoidance behavior and quality of life in IBS patients. Thirteen patients with IBS according to Rome III criteria participated in a single-case experimental study using a five-week baseline and a subsequent twelve-session intervention phase focusing on psycho-education, mindfulness and in vivo exposure. Standardized measurement of gastrointestinal symptoms, pain catastrophizing, avoidance behavior and quality of life was conducted weekly during baseline as well as intervention phase and at six-month follow-up. Results showed that over 70% of patients improved significantly on gastrointestinal symptoms, pain catastrophizing, and quality of life. Effects on avoidance behavior were modest. These results strengthen and extend earlier findings and provide further support for the efficacy of exposure-based strategies for IBS.

Case study: videogame distraction reduces behavioral distress in a preschool-aged child undergoing repeated burn dressing changes: a single-subject design.

Science.gov (United States)

Sil, Soumitri; Dahlquist, Lynnda M; Burns, Andrew J

2013-04-01

This single-subject design study evaluated the feasibility and efficacy of passive and interactive videogame distraction on behavioral distress for a preschool-aged child receiving repeated burn dressing changes. A 4-year-old girl underwent 3 baseline and 10 videogame distraction sessions (5 passive and 5 interactive) using a restricted alternating treatments design. Observed behavioral distress was coded, and parents and nurses rated the child's distress and cooperative behavior. Relative to baseline, behavioral distress decreased and cooperative behavior increased immediately after the onset of videogame distraction. Single Case Randomization Tests revealed significantly lower behavioral distress and greater cooperation during interactive videogame distraction relative to passive videogame distraction. Interactive videogame distraction appears to be a feasible and effective pain management strategy for a preschool-aged child undergoing repeated painful medical procedures.

Simulation and Experimental Studies on Grain Selection and Structure Design of the Spiral Selector for Casting Single Crystal Ni-Based Superalloy.

Science.gov (United States)

Zhang, Hang; Xu, Qingyan

2017-10-27

Grain selection is an important process in single crystal turbine blades manufacturing. Selector structure is a control factor of grain selection, as well as directional solidification (DS). In this study, the grain selection and structure design of the spiral selector were investigated through experimentation and simulation. A heat transfer model and a 3D microstructure growth model were established based on the Cellular automaton-Finite difference (CA-FD) method for the grain selector. Consequently, the temperature field, the microstructure and the grain orientation distribution were simulated and further verified. The average error of the temperature result was less than 1.5%. The grain selection mechanisms were further analyzed and validated through simulations. The structural design specifications of the selector were suggested based on the two grain selection effects. The structural parameters of the spiral selector, namely, the spiral tunnel diameter ( d w ), the spiral pitch ( h b ) and the spiral diameter ( h s ), were studied and the design criteria of these parameters were proposed. The experimental and simulation results demonstrated that the improved selector could accurately and efficiently produce a single crystal structure.

POBE: A Computer Program for Optimal Design of Multi-Subject Blocked fMRI Experiments

Directory of Open Access Journals (Sweden)

Bärbel Maus

2014-01-01

Full Text Available For functional magnetic resonance imaging (fMRI studies, researchers can use multi-subject blocked designs to identify active brain regions for a certain stimulus type of interest. Before performing such an experiment, careful planning is necessary to obtain efficient stimulus effect estimators within the available financial resources. The optimal number of subjects and the optimal scanning time for a multi-subject blocked design with fixed experimental costs can be determined using optimal design methods. In this paper, the user-friendly computer program POBE 1.2 (program for optimal design of blocked experiments, version 1.2 is presented. POBE provides a graphical user interface for fMRI researchers to easily and efficiently design their experiments. The computer program POBE calculates the optimal number of subjects and the optimal scanning time for user specified experimental factors and model parameters so that the statistical efficiency is maximised for a given study budget. POBE can also be used to determine the minimum budget for a given power. Furthermore, a maximin design can be determined as efficient design for a possible range of values for the unknown model parameters. In this paper, the computer program is described and illustrated with typical experimental factors for a blocked fMRI experiment.

Early Intervention for Children with Conduct Disorders: A Quantitative Synthesis of Single-Subject Research.

Science.gov (United States)

Scruggs, Thomas E.; And Others

1986-01-01

Sixteen studies were analyzed that employed single-subject designs focusing on conduct disorders in preschoolers. Results indicated that reinforcement produced most positive outcomes, followed by punishment, timeout, and differential attention. Subject characteristics such as sex, handicapping condition, and target behavior typically bore little…

SCRAED - Simple and Complex Random Assignment in Experimental Designs

OpenAIRE

Alferes, Valentim R.

2009-01-01

SCRAED is a package of 37 self-contained SPSS syntax files that performs simple and complex random assignment in experimental designs. For between-subjects designs, SCRAED includes simple random assignment (no restrictions, forced equal sizes, forced unequal sizes, and unequal probabilities), block random assignment (simple and generalized blocks), and stratified random assignment (no restrictions, forced equal sizes, forced unequal sizes, and unequal probabilities). For within-subject...

Masked Visual Analysis: Minimizing Type I Error in Visually Guided Single-Case Design for Communication Disorders.

Science.gov (United States)

Byun, Tara McAllister; Hitchcock, Elaine R; Ferron, John

2017-06-10

Single-case experimental designs are widely used to study interventions for communication disorders. Traditionally, single-case experiments follow a response-guided approach, where design decisions during the study are based on participants' observed patterns of behavior. However, this approach has been criticized for its high rate of Type I error. In masked visual analysis (MVA), response-guided decisions are made by a researcher who is blinded to participants' identities and treatment assignments. MVA also makes it possible to conduct a hypothesis test assessing the significance of treatment effects. This tutorial describes the principles of MVA, including both how experiments can be set up and how results can be used for hypothesis testing. We then report a case study showing how MVA was deployed in a multiple-baseline across-subjects study investigating treatment for residual errors affecting rhotics. Strengths and weaknesses of MVA are discussed. Given their important role in the evidence base that informs clinical decision making, it is critical for single-case experimental studies to be conducted in a way that allows researchers to draw valid inferences. As a method that can increase the rigor of single-case studies while preserving the benefits of a response-guided approach, MVA warrants expanded attention from researchers in communication disorders.

Single-Case Designs and Qualitative Methods: Applying a Mixed Methods Research Perspective

Science.gov (United States)

Hitchcock, John H.; Nastasi, Bonnie K.; Summerville, Meredith

2010-01-01

The purpose of this conceptual paper is to describe a design that mixes single-case (sometimes referred to as single-subject) and qualitative methods, hereafter referred to as a single-case mixed methods design (SCD-MM). Minimal attention has been given to the topic of applying qualitative methods to SCD work in the literature. These two…

Robustness of crossover trials against subject drop-out - Examples of perpetually connected designs.

Science.gov (United States)

Godolphin, P J; Godolphin, E J

2017-01-01

When performing a repeated measures experiment, such as a clinical trial, there is a risk of subject drop-out during the experiment. If one or more subjects leave the study prematurely, a situation could arise where the eventual design is disconnected, implying that very few treatment contrasts for both direct effects and carryover effects are estimable. This paper aims to identify experimental conditions where this problem with the eventual design can be avoided. It is shown that in the class of uniformly balanced repeated measurement designs consisting of two or more Latin squares, there are planned designs with the following useful property. Provided that all subjects have completed the first two periods of study, such a design will not be replaced by a disconnected eventual design due to drop-out, irrespective of the type of drop-out behaviour that may occur. Designs with this property are referred to as perpetually connected. These experimental conditions are identified and examined in the paper and an example of at least one perpetually connected uniformly balanced repeated measurement design is given in each case. The results improve upon previous contributions in the literature that have been confined largely to cases in which drop-out occurs only in the final periods of study.

Achieving optimal SERS through enhanced experimental design.

Science.gov (United States)

Fisk, Heidi; Westley, Chloe; Turner, Nicholas J; Goodacre, Royston

2016-01-01

One of the current limitations surrounding surface-enhanced Raman scattering (SERS) is the perceived lack of reproducibility. SERS is indeed challenging, and for analyte detection, it is vital that the analyte interacts with the metal surface. However, as this is analyte dependent, there is not a single set of SERS conditions that are universal. This means that experimental optimisation for optimum SERS response is vital. Most researchers optimise one factor at a time, where a single parameter is altered first before going onto optimise the next. This is a very inefficient way of searching the experimental landscape. In this review, we explore the use of more powerful multivariate approaches to SERS experimental optimisation based on design of experiments and evolutionary computational methods. We particularly focus on colloidal-based SERS rather than thin film preparations as a result of their popularity. © 2015 The Authors. Journal of Raman Spectroscopy published by John Wiley & Sons, Ltd.

Methods for the neutronic design of a Supersara experimental loop

International Nuclear Information System (INIS)

Casali, F.; Cepraga, D.

1982-01-01

This paper describes a method for the neutronic design of experimental loops irradiated in D 2 O experimental reactors, like Essor. The calculation approach concerns the definition of a Weigner-Seitz cell where the loop under examination be subjected to the same neutronic conditions as in the actual reactor

Optimal experimental design with R

CERN Document Server

Rasch, Dieter; Verdooren, L R; Gebhardt, Albrecht

2011-01-01

Experimental design is often overlooked in the literature of applied and mathematical statistics: statistics is taught and understood as merely a collection of methods for analyzing data. Consequently, experimenters seldom think about optimal design, including prerequisites such as the necessary sample size needed for a precise answer for an experimental question. Providing a concise introduction to experimental design theory, Optimal Experimental Design with R: Introduces the philosophy of experimental design Provides an easy process for constructing experimental designs and calculating necessary sample size using R programs Teaches by example using a custom made R program package: OPDOE Consisting of detailed, data-rich examples, this book introduces experimenters to the philosophy of experimentation, experimental design, and data collection. It gives researchers and statisticians guidance in the construction of optimum experimental designs using R programs, including sample size calculations, hypothesis te...

Single-well experimental design for studying residual trapping of superciritcal carbon dioxide

Energy Technology Data Exchange (ETDEWEB)

Zhang, Y.; Freifeld, B.; Finsterle, S.; Leahy, M.; Ennis-King, J.; Paterson, L.; Dance, T.

2010-06-15

The objective of our research is to design a single-well injection-withdrawal test to evaluate residual phase trapping at potential CO{sub 2} geological storage sites. Given the significant depths targeted for CO{sub 2} storage and the resulting high costs associated with drilling to those depths, it is attractive to develop a single-well test that can provide data to assess reservoir properties and reduce uncertainties in the appraisal phase of site investigation. The main challenges in a single-well test design include (1) difficulty in quantifying the amount of CO{sub 2} that has dissolved into brine or migrated away from the borehole; (2) non-uniqueness and uncertainty in the estimate of the residual gas saturation (S{sub gr}) due to correlations among various parameters; and (3) the potential biased S{sub gr} estimate due to unaccounted heterogeneity of the geological medium. To address each of these challenges, we propose (1) to use a physical-based model to simulation test sequence and inverse modeling to analyze data information content and to quantify uncertainty; (2) to jointly use multiple data types generated from different kinds of tests to constrain the Sgr estimate; and (3) to reduce the sensitivity of the designed tests to geological heterogeneity by conducting the same test sequence in both a water-saturated system and a system with residual gas saturation. To perform the design calculation, we build a synthetic model and conduct a formal analysis for sensitivity and uncertain quantification. Both parametric uncertainty and geological uncertainty are considered in the analysis. Results show (1) uncertainty in the estimation of Sgr can be reduced by jointly using multiple data types and repeated tests; and (2) geological uncertainty is essential and needs to be accounted for in the estimation of S{sub gr} and its uncertainty. The proposed methodology is applied to the design of a CO{sub 2} injection test at CO2CRC's Otway Project Site, Victoria

Imagery Rescripting for Body Dysmorphic Disorder: A Multiple-Baseline Single-Case Experimental Design.

Science.gov (United States)

Willson, Rob; Veale, David; Freeston, Mark

2016-03-01

Individuals with body dysmorphic disorder (BDD) often experience negative distorted images of their appearance, and research suggests these may be linked to memories of adverse events such as bullying or teasing. This study evaluates imagery rescripting (ImR) as an intervention for BDD. In this article, we present a multiple-baseline single-case experimental design testing imagery rescripting as a brief, stand-alone intervention, with six individuals with BDD that related to aversive memories. The impact of the intervention was assessed by self-reported daily measures of symptom severity (preoccupation with appearance, appearance-related checking behaviors, appearance-related distress, and strength of belief that their main problem is their appearance) and standardized clinician ratings of BDD severity (Yale-Brown Obsessive Compulsive Scale modified for BDD). Four out of six of the participants responded positively to the intervention, with clinically meaningful improvement in symptomatology. Overall response was rapid; improvements began within the first week post-ImR intervention. From a small sample it is cautiously concluded that imagery rescripting may show promise as a module in cognitive-behavioral therapy for BDD, and is worthy of further investigation. Copyright © 2015. Published by Elsevier Ltd.

Design and experimentation of BSFQ logic devices

International Nuclear Information System (INIS)

Hosoki, T.; Kodaka, H.; Kitagawa, M.; Okabe, Y.

1999-01-01

Rapid single flux quantum (RSFQ) logic needs synchronous pulses for each gate, so the clock-wiring problem is more serious when designing larger scale circuits with this logic. So we have proposed a new SFQ logic which follows Boolean algebra perfectly by using set and reset pulses. With this logic, the level information of current input is transmitted with these pulses generated by level-to-pulse converters, and each gate calculates logic using its phase level made by these pulses. Therefore, our logic needs no clock in each gate. We called this logic 'Boolean SFQ (BSFQ) logic'. In this paper, we report design and experimentation for an AND gate with inverting input based on BSFQ logic. The experimental results for OR and XOR gates are also reported. (author)

Experimental Studies on Behaviour of Reinforced Geopolymer Concrete Beams Subjected to Monotonic Static Loading

Science.gov (United States)

Madheswaran, C. K.; Ambily, P. S.; Dattatreya, J. K.; Ramesh, G.

2015-06-01

This work describes the experimental investigation on behaviour of reinforced GPC beams subjected to monotonic static loading. The overall dimensions of the GPC beams are 250 mm × 300 mm × 2200 mm. The effective span of beam is 1600 mm. The beams have been designed to be critical in shear as per IS:456 provisions. The specimens were produced from a mix incorporating fly ash and ground granulated blast furnace slag, which was designed for a compressive strength of 40 MPa at 28 days. The reinforced concrete specimens are subjected to curing at ambient temperature under wet burlap. The parameters being investigated include shear span to depth ratio (a/d = 1.5 and 2.0). Experiments are conducted on 12 GPC beams and four OPCC control beams. All the beams are tested using 2000 kN servo-controlled hydraulic actuator. This paper presents the results of experimental studies.

Experimental study of single event burnout and single event gate rupture in power MOSFETs and IGBT

International Nuclear Information System (INIS)

Tang Benqi; Wang Yanping; Geng Bin

2001-01-01

An experimental study was carried out to determine the single event burnout and single event gate rupture sensitivities in power MOSFETs and IGBT which were exposed to heavy ions from 252 Cf source. The test method, test results, a description of observed burnout current waveforms and a discussion of a possible failure mechanism were presented. Current measurements have been performed with a specially designed circuit. The test results include the observed dependence upon applied drain or gate to source bias and versus with external capacitors and limited resistors

Alliance-focused therapy for anorexia nervosa: integrative relational and behavioral change treatments in a single-case experimental design.

Science.gov (United States)

Satir, Dana A; Goodman, David M; Shingleton, Rebecca M; Porcerelli, John H; Gorman, Bernard S; Pratt, Elizabeth M; Barlow, David H; Thompson-Brenner, Heather

2011-12-01

Evidence supporting outpatient treatments for anorexia nervosa (AN) is severely lacking, due to low retention and poor outcome. One explanation for drop-out is weak treatment alliances. A single-case experimental analysis accompanied by in-depth qualitative description is presented for Ms. O, who received a novel treatment for AN called Alliance Focused Treatment (AFT) that attends to ruptures in the alliance, interpersonal difficulties and emotional avoidance. At intake Ms. O met diagnostic criteria for AN, Major Depressive Disorder, and Social Phobia. She was characterized as having symptoms of Obsessive Compulsive, Avoidant, and Depressive personality disorders. Treatment began with a Baseline followed by the experimental (AFT) and comparison treatments (Behavioral Change Treatment [BCT]) using a replicated experimental single-case phase change design. Graphs of slopes of kilocalorie and alliance change facilitated observation of treatment effects. Ms. O participated in 16 sessions of AFT and 8 sessions of BCT with specific benefits. Ratings of the treatment alliance were consistently high and she evidenced significant changes in weight, quality of life, and personality pathology. Associations between rupture/repair episodes and kilocalorie increases were observed. The utility of the treatment relationship in facilitating emotional expression was evident. At posttreatment, Ms. O endorsed cognitive AN symptoms, although these were not explicitly treated. This study provides preliminary support for the feasibility and effect of AFT and BCT, and highlights the importance of the alliance in treating adults with AN. Further research on emotion regulation in AN and its effect on the treatment relationship are needed.

Self-Management Interventions on Students with Autism: A Meta-Analysis of Single-Subject Research

Science.gov (United States)

Carr, Monica E.; Moore, Dennis W.; Anderson, Angelika

2014-01-01

Self-management interventions aimed at skill acquisition and/or improving behavior of students diagnosed with autism spectrum disorders were examined. Twenty-three single-subject research design studies met inclusion criteria. Quality assessment of these studies was conducted using the What Works Clearinghouse guidelines, and treatment effect…

No Randomization? No Problem: Experimental Control and Random Assignment in Single Case Research

Science.gov (United States)

Ledford, Jennifer R.

2018-01-01

Randomization of large number of participants to different treatment groups is often not a feasible or preferable way to answer questions of immediate interest to professional practice. Single case designs (SCDs) are a class of research designs that are experimental in nature but require only a few participants, all of whom receive the…

Robust Bayesian Experimental Design for Conceptual Model Discrimination

Science.gov (United States)

Pham, H. V.; Tsai, F. T. C.

2015-12-01

A robust Bayesian optimal experimental design under uncertainty is presented to provide firm information for model discrimination, given the least number of pumping wells and observation wells. Firm information is the maximum information of a system can be guaranteed from an experimental design. The design is based on the Box-Hill expected entropy decrease (EED) before and after the experiment design and the Bayesian model averaging (BMA) framework. A max-min programming is introduced to choose the robust design that maximizes the minimal Box-Hill EED subject to that the highest expected posterior model probability satisfies a desired probability threshold. The EED is calculated by the Gauss-Hermite quadrature. The BMA method is used to predict future observations and to quantify future observation uncertainty arising from conceptual and parametric uncertainties in calculating EED. Monte Carlo approach is adopted to quantify the uncertainty in the posterior model probabilities. The optimal experimental design is tested by a synthetic 5-layer anisotropic confined aquifer. Nine conceptual groundwater models are constructed due to uncertain geological architecture and boundary condition. High-performance computing is used to enumerate all possible design solutions in order to identify the most plausible groundwater model. Results highlight the impacts of scedasticity in future observation data as well as uncertainty sources on potential pumping and observation locations.

Using single-case experimental design methodology to evaluate the effects of the ABC method for nursing staff on verbal aggressive behaviour after acquired brain injury.

Science.gov (United States)

Winkens, Ieke; Ponds, Rudolf; Pouwels, Climmy; Eilander, Henk; van Heugten, Caroline

2014-01-01

The ABC method is a basic and simplified form of behavioural modification therapy for use by nurses. ABC refers to the identification of Antecedent events, target Behaviours, and Consequent events. A single-case experimental AB design was used to evaluate the effects of the ABC method on a woman diagnosed with olivo-ponto-cerebellar ataxia. Target behaviour was verbal aggressive behaviour during ADL care, assessed at 9 time points immediately before implementation of the ABC method and at 36 time points after implementation. A randomisation test showed a significant treatment effect between the baseline and intervention phases (t = .58, p = .03; ES [Nonoverlap All Pairs] = .62). Visual analysis, however, showed that the target behaviour was still present after implementation of the method and that on some days the nurses even judged the behaviour to be more severe than at baseline. Although the target behaviour was still present after treatment, the ABC method seems to be a promising tool for decreasing problem behaviour in patients with acquired brain injury. It is worth investigating the effects of this method in future studies. When interpreting single-subject data, both visual inspection and statistical analysis are needed to determine whether treatment is effective and whether the effects lead to clinically desirable results.

An experimentally validated fatigue model for wood subjected to tension perpendicular to the grain

DEFF Research Database (Denmark)

Clorius, Christian Odin; Pedersen, Martin Uhre; Hoffmeyer, Preben

2009-01-01

This study presents an experimental investigation of fatigue in wood subjected to tension perpendicular to the grain. The study has been designed with special reference to the influence of the frequency of loading. The investigation reveals an interaction between number of load oscillations and a...... a good basis....

Experimental Engineering: Articulating and Valuing Design Experimentation

DEFF Research Database (Denmark)

Vallgårda, Anna; Grönvall, Erik; Fritsch, Jonas

2017-01-01

In this paper we propose Experimental Engineering as a way to articulate open- ended technological experiments as a legitimate design research practice. Experimental Engineering introduces a move away from an outcome or result driven design process towards an interest in existing technologies and...

Computational/experimental studies of isolated, single component droplet combustion

Science.gov (United States)

Dryer, Frederick L.

1993-01-01

Isolated droplet combustion processes have been the subject of extensive experimental and theoretical investigations for nearly 40 years. The gross features of droplet burning are qualitatively embodied by simple theories and are relatively well understood. However, there remain significant aspects of droplet burning, particularly its dynamics, for which additional basic knowledge is needed for thorough interpretations and quantitative explanations of transient phenomena. Spherically-symmetric droplet combustion, which can only be approximated under conditions of both low Reynolds and Grashof numbers, represents the simplest geometrical configuration in which to study the coupled chemical/transport processes inherent within non-premixed flames. The research summarized here, concerns recent results on isolated, single component, droplet combustion under microgravity conditions, a program pursued jointly with F.A. Williams of the University of California, San Diego. The overall program involves developing and applying experimental methods to study the burning of isolated, single component droplets, in various atmospheres, primarily at atmospheric pressure and below, in both drop towers and aboard space-based platforms such as the Space Shuttle or Space Station. Both computational methods and asymptotic methods, the latter pursued mainly at UCSD, are used in developing the experimental test matrix, in analyzing results, and for extending theoretical understanding. Methanol, and the normal alkanes, n-heptane, and n-decane, have been selected as test fuels to study time-dependent droplet burning phenomena. The following sections summarizes the Princeton efforts on this program, describe work in progress, and briefly delineate future research directions.

Esthetic Evaluation of Anterior Single-Tooth Implants with Different Abutment Designs-Patients' Satisfaction Compared to Dentists' Observations.

Science.gov (United States)

Patil, Ratnadeep; Gresnigt, Marco M M; Mahesh, Kavita; Dilbaghi, Anjali; Cune, Marco S

2017-07-01

To correlate patients' satisfaction and dentists' observations regarding two abutment designs used for single crowns in the esthetic zone: a divergent one (control) and a curved one (experimental), with special emphasis on muco-gingival esthetics. Twenty-six patients with nonadjacent missing teeth in the esthetic zone were enrolled in a randomized clinical trial (within-subject comparison). Two implants placed in each were restored using abutments of different geometry. Patients' appreciation was assessed on a visual analog scale (VAS) by recording answers to three questions, and dentists' appreciation was determined by means of the Pink Esthetic Score (PES) at T0 (crown cementation, baseline) and at T12 (1 year post-cementation). ANOVA with post hoc analysis was used to identify differences between groups and at different moments in time. Pearson correlations were calculated between all variables, both at T0 and at T12. No statistically significant differences were found at any time between the control and experimental abutment design, either for the PES or for the VAS score. PES slightly improved after 1 year, as did the VAS rating related to functioning with the implant-crown compared to the natural teeth. All PES and VAS scores demonstrated highly significant correlation. Both patient satisfaction and professional appreciation of muco-gingival conditions after single implant treatment in the esthetic zone were high; however, the curved, experimental abutment design performed no better than the conventional, divergent type. Curved abutment design does not significantly impact crown or gingival esthetics as assessed by PES and VAS scored by dentists and patients, respectively. © 2016 by the American College of Prosthodontists.

Development of the complex general linear model in the Fourier domain: application to fMRI multiple input-output evoked responses for single subjects.

Science.gov (United States)

Rio, Daniel E; Rawlings, Robert R; Woltz, Lawrence A; Gilman, Jodi; Hommer, Daniel W

2013-01-01

A linear time-invariant model based on statistical time series analysis in the Fourier domain for single subjects is further developed and applied to functional MRI (fMRI) blood-oxygen level-dependent (BOLD) multivariate data. This methodology was originally developed to analyze multiple stimulus input evoked response BOLD data. However, to analyze clinical data generated using a repeated measures experimental design, the model has been extended to handle multivariate time series data and demonstrated on control and alcoholic subjects taken from data previously analyzed in the temporal domain. Analysis of BOLD data is typically carried out in the time domain where the data has a high temporal correlation. These analyses generally employ parametric models of the hemodynamic response function (HRF) where prewhitening of the data is attempted using autoregressive (AR) models for the noise. However, this data can be analyzed in the Fourier domain. Here, assumptions made on the noise structure are less restrictive, and hypothesis tests can be constructed based on voxel-specific nonparametric estimates of the hemodynamic transfer function (HRF in the Fourier domain). This is especially important for experimental designs involving multiple states (either stimulus or drug induced) that may alter the form of the response function.

Experimental Device for Learning of Logical Circuit Design using Integrated Circuits

OpenAIRE

石橋, 孝昭

2012-01-01

This paper presents an experimental device for learning of logical circuit design using integrated circuits and breadboards. The experimental device can be made at a low cost and can be used for many subjects such as logical circuits, computer engineering, basic electricity, electrical circuits and electronic circuits. The proposed device is effective to learn the logical circuits than the usual lecture.

Design and Implementation of an Experimental Cataloging Advisor--Mapper.

Science.gov (United States)

Ercegovac, Zorana; Borko, Harold

1992-01-01

Describes the design of an experimental computer-aided cataloging advisor, Mapper, that was developed to help novice users with the descriptive cataloging of single-sheet maps from U.S. publishers. The human-computer interface is considered, the use of HyperCard is discussed, the knowledge base is explained, and assistance screens are described.…

Fundamentals of statistical experimental design and analysis

CERN Document Server

Easterling, Robert G

2015-01-01

Professionals in all areas - business; government; the physical, life, and social sciences; engineering; medicine, etc. - benefit from using statistical experimental design to better understand their worlds and then use that understanding to improve the products, processes, and programs they are responsible for. This book aims to provide the practitioners of tomorrow with a memorable, easy to read, engaging guide to statistics and experimental design. This book uses examples, drawn from a variety of established texts, and embeds them in a business or scientific context, seasoned with a dash of humor, to emphasize the issues and ideas that led to the experiment and the what-do-we-do-next? steps after the experiment. Graphical data displays are emphasized as means of discovery and communication and formulas are minimized, with a focus on interpreting the results that software produce. The role of subject-matter knowledge, and passion, is also illustrated. The examples do not require specialized knowledge, and t...

Positive design : An introduction to design for subjective well-being

NARCIS (Netherlands)

Desmet, P.M.A.; Pohlmeyer, A.E.

2013-01-01

This paper addresses the question of how design can contribute to the happiness of individuals–to their subjective well-being. A framework for positive design is introduced that includes three main components of subjective well-being: pleasure, personal significance and virtue. Each component

The Influence of Function, Topography, and Setting on Noncontingent Reinforcement Effect Sizes for Reduction in Problem Behavior: A Meta-Analysis of Single-Case Experimental Design Data

Science.gov (United States)

Ritter, William A.; Barnard-Brak, Lucy; Richman, David M.; Grubb, Laura M.

2018-01-01

Richman et al. ("J Appl Behav Anal" 48:131-152, 2015) completed a meta-analytic analysis of single-case experimental design data on noncontingent reinforcement (NCR) for the treatment of problem behavior exhibited by individuals with developmental disabilities. Results showed that (1) NCR produced very large effect sizes for reduction in…

Experimental research on the ultimate strength of hard aluminium alloy 2017 subjected to short-time radioactive heating

International Nuclear Information System (INIS)

Dafang, Wu; Yuewu, Wang; Bing, Pan; Meng, Mu; Lin, Zhu

2012-01-01

Highlights: ► Ultimate strength at transient heating is critical to security design of missiles. ► We measure the ultimate strength of alloy 2017 subjected to transient heating. ► Experimental results at transient heating are lacking in strength design handbook. ► Ultimate strength of alloy 2017 experimented is much higher than handbook value. ► The results provide a new method for optimal design of high-speed flight vehicles. -- Abstract: Alloy 2017 (Al–Cu–Mg) is a hard aluminium alloy strengthened by heat treatment. Because of its higher strength, finer weldability and ductility, hard aluminium alloy 2017 has been widely used in the field of aeronautics and astronautics. However, the ultimate strength and other characteristic mechanical parameters of aluminium alloy 2017 in a transient heating environment are still unclear, as these key mechanical parameters are lacking in the existing strength design handbook. The experimental characterisation of these critical parameters of aluminium alloy 2017 is undoubtedly meaningful for reliably estimating life span of and improving safety in designing high-speed flight vehicles. In this paper, the high-temperature ultimate strength, loading time and other mechanical properties of hard aluminium alloy 2017 under different transient heating temperatures and loading conditions are investigated by combining a transient aerodynamic heating simulation system and a material testing machine. The experimental results reveal that the ultimate strength and loading capability of aluminium alloy 2017 subjected to transient thermal heating are much higher than those tested in a long-time stable high-temperature environment. The research of this work not only provides a substantial basis for the loading capability improvement and optimal design of aerospace materials and structures subject to transient heating but also presents a new research direction with a practical application value.

Experimental Design Research

DEFF Research Database (Denmark)

This book presents a new, multidisciplinary perspective on and paradigm for integrative experimental design research. It addresses various perspectives on methods, analysis and overall research approach, and how they can be synthesized to advance understanding of design. It explores the foundations...... of experimental approaches and their utility in this domain, and brings together analytical approaches to promote an integrated understanding. The book also investigates where these approaches lead to and how they link design research more fully with other disciplines (e.g. psychology, cognition, sociology......, computer science, management). Above all, the book emphasizes the integrative nature of design research in terms of the methods, theories, and units of study—from the individual to the organizational level. Although this approach offers many advantages, it has inherently led to a situation in current...

Masked Visual Analysis: Minimizing Type I Error in Visually Guided Single-Case Design for Communication Disorders

Science.gov (United States)

Byun, Tara McAllister; Hitchcock, Elaine R.; Ferron, John

2017-01-01

Purpose: Single-case experimental designs are widely used to study interventions for communication disorders. Traditionally, single-case experiments follow a response-guided approach, where design decisions during the study are based on participants' observed patterns of behavior. However, this approach has been criticized for its high rate of…

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1985-01-01

The Fusion Experimental Reactor (FER) being developed at JAERI as a next generation tokamak to JT-60 has a major mission of realizing a self-ignited long-burning DT plasma and demonstrating engineering feasibility. During FY82 and FY83 a comprehensive and intensive conceptual design study has been conducted for a pulsed operation FER as a reference option which employs a conventional inductive current drive and a double-null divertor. In parallel with the reference design, studies have been carried out to evaluate advanced reactor concepts such as quasi-steady state operation and steady state operation based on RF current drive and pumped limiter, and comparative studies for single-null divertor/pumped limiter. This report presents major results obtained primarily from FY83 design studies, while the results of FY82 design studies are described in previous references (JAERI-M 83-213--216). (author)

Study of Formulation Variables Influencing Polymeric Microparticles by Experimental Design

Directory of Open Access Journals (Sweden)

Jitendra B. Naik

2014-04-01

Full Text Available The objective of this study was to prepare diclofenac sodium loaded microparticles by single emulsion [oil-in-water (o/w] solvent evaporation method. The 22 experimental design methodology was used to evaluate the effect of two formulation variables on microspheres properties using the Design-Expert® software and evaluated for their particle size, morphology, and encapsulation efficiency and in vitro drug release. The graphical and mathematical analysis of the design showed that the independent variables were a significant effect on the encapsulation efficiency and drug release of microparticles. The low magnitudes of error and significant values of R2 prove the high prognostic ability of the design. The microspheres showed high encapsulation efficiency with an increase in the amount of polymer and decrease in the amount of PVA in the formulation. The particles were found to be spherical with smooth surface. Prolonged drug release and enhancement of encapsulation efficiency of polymeric microparticles can be successfully obtained with an application of experimental design technique.

Experimental techniques for single cell and single molecule biomechanics

International Nuclear Information System (INIS)

Lim, C.T.; Zhou, E.H.; Li, A.; Vedula, S.R.K.; Fu, H.X.

2006-01-01

Stresses and strains that act on the human body can arise either from external physical forces or internal physiological environmental conditions. These biophysical interactions can occur not only at the musculoskeletal but also cellular and molecular levels and can determine the health and function of the human body. Here, we seek to investigate the structure-property-function relationship of cells and biomolecules so as to understand their important physiological functions as well as establish possible connections to human diseases. With the recent advancements in cell and molecular biology, biophysics and nanotechnology, several innovative and state-of-the-art experimental techniques and equipment have been developed to probe the structural and mechanical properties of biostructures from the micro- down to picoscale. Some of these experimental techniques include the optical or laser trap method, micropipette aspiration, step-pressure technique, atomic force microscopy and molecular force spectroscopy. In this article, we will review the basic principles and usage of these techniques to conduct single cell and single molecule biomechanics research

Quasi-Experimental Designs for Causal Inference

Science.gov (United States)

Kim, Yongnam; Steiner, Peter

2016-01-01

When randomized experiments are infeasible, quasi-experimental designs can be exploited to evaluate causal treatment effects. The strongest quasi-experimental designs for causal inference are regression discontinuity designs, instrumental variable designs, matching and propensity score designs, and comparative interrupted time series designs. This…

Development and Validation of a Rubric for Diagnosing Students’ Experimental Design Knowledge and Difficulties

Science.gov (United States)

Dasgupta, Annwesa P.; Anderson, Trevor R.

2014-01-01

It is essential to teach students about experimental design, as this facilitates their deeper understanding of how most biological knowledge was generated and gives them tools to perform their own investigations. Despite the importance of this area, surprisingly little is known about what students actually learn from designing biological experiments. In this paper, we describe a rubric for experimental design (RED) that can be used to measure knowledge of and diagnose difficulties with experimental design. The development and validation of the RED was informed by a literature review and empirical analysis of undergraduate biology students’ responses to three published assessments. Five areas of difficulty with experimental design were identified: the variable properties of an experimental subject; the manipulated variables; measurement of outcomes; accounting for variability; and the scope of inference appropriate for experimental findings. Our findings revealed that some difficulties, documented some 50 yr ago, still exist among our undergraduate students, while others remain poorly investigated. The RED shows great promise for diagnosing students’ experimental design knowledge in lecture settings, laboratory courses, research internships, and course-based undergraduate research experiences. It also shows potential for guiding the development and selection of assessment and instructional activities that foster experimental design. PMID:26086658

Fast Bayesian optimal experimental design and its applications

KAUST Repository

Long, Quan

2015-01-07

We summarize our Laplace method and multilevel method of accelerating the computation of the expected information gain in a Bayesian Optimal Experimental Design (OED). Laplace method is a widely-used method to approximate an integration in statistics. We analyze this method in the context of optimal Bayesian experimental design and extend this method from the classical scenario, where a single dominant mode of the parameters can be completely-determined by the experiment, to the scenarios where a non-informative parametric manifold exists. We show that by carrying out this approximation the estimation of the expected Kullback-Leibler divergence can be significantly accelerated. While Laplace method requires a concentration of measure, multi-level Monte Carlo method can be used to tackle the problem when there is a lack of measure concentration. We show some initial results on this approach. The developed methodologies have been applied to various sensor deployment problems, e.g., impedance tomography and seismic source inversion.

Attention Process Training-3 to improve reading comprehension in mild aphasia: A single-case experimental design study.

Science.gov (United States)

Lee, Jaime B; Sohlberg, McKay Moore; Harn, Beth; Horner, Robert; Cherney, Leora R

2018-06-04

People with aphasia frequently present with nonlinguistic deficits, in addition to their compromised language abilities, which may contribute to their problems with reading comprehension. Treatment of attention, working memory and executive control may improve reading comprehension in individuals with aphasia, particularly those with mild reading problems. This single-case experimental design study evaluated the efficacy of Attention Process Training-3, an intervention combining direct attention training and metacognitive facilitation, for improving reading comprehension in individuals with mild aphasia. A multiple baseline design across six participants was used to evaluate treatment effects. The primary outcome measure was a maze reading task. Cognitive measures were administered pre- and post-treatment. Visual inspection of graphed maze reading performance data indicated a basic effect between APT-3 and improved maze reading for three of the six participants. Quantitative analyses, using Tau-U, corroborated findings identified through visual analysis. The overall effect size was significant (Tau = .48, p = .01). Results suggest that APT-3 has the potential to improve reading in individuals with aphasia, but that it may be more efficacious under certain conditions. Treatment and participant variables, including intensity of treatment and metacognitive strategy usage, are discussed as potential influences on participants' responsiveness to APT-3.

Evaluation of electrical aversion therapy for inappropriate sexual behaviour after traumatic brain injury: a single case experimental design study

Science.gov (United States)

ter Mors, Bert Jan; van Heugten, Caroline M; van Harten, Peter N

2012-01-01

Inappropriate sexual behaviour after acquired brain injury is a severe complication. Evidence for effective treatment is not available. Electrical aversion therapy (EAT) is a behavioural therapeutic option used in persons with intellectual disabilities, which might be suitable for brain-injured individuals for whom other therapies are not effective. The effect of EAT in brain injury has not been investigated previously. A single case experimental design was used. In an ABBA (baseline-treatment-treatment-withdrawal) design the frequency of the target behaviour (ie, inappropriate sexual behaviour) in a 40-year-old man was measured daily. A total of 551 measurements were recorded. A significant reduction of the target behaviour was seen after the first treatment phase (baseline 12.18 (2.59) vs 3.15 (3.19) mean target behaviours daily); this reduction remained stable over time. We conclude that EAT was effective in this patient with inappropriate sexual behaviour due to severe brain injury. EAT can therefore be considered in therapy resistant inappropriate sexual behaviour in brain-injured patients. PMID:22922913

Crossover learning of gestures in two ideomotor apraxia patients: A single case experimental design study.

Science.gov (United States)

Shimizu, Daisuke; Tanemura, Rumi

2017-06-01

Crossover learning may aid rehabilitation in patients with neurological disorders. Ideomotor apraxia (IMA) is a common sequela of left-brain damage that comprises a deficit in the ability to perform gestures to verbal commands or by imitation. This study elucidated whether crossover learning occurred in two post-stroke IMA patients without motor paralysis after gesture training approximately 2 months after stroke onset. We quantitatively analysed the therapeutic intervention history and investigated whether revised action occurred during gesture production. Treatment intervention was to examine how to influence improvement and generalisation of the ability to produce the gesture. This study used an alternating treatments single-subject design, and the intervention method was errorless learning. Results indicated crossover learning in both patients. Qualitative analysis indicated that revised action occurred during the gesture-production process in one patient and that there were two types of post-revised action gestures: correct and incorrect gestures. We also discovered that even when a comparably short time had elapsed since stroke onset, generalisation was difficult. Information transfer between the left and right hemispheres of the brain via commissural fibres is important in crossover learning. In conclusion, improvements in gesture-production skill should be made with reference to the left cerebral hemisphere disconnection hypothesis.

Design study of the experimental multi-purpose high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Tsunoda, Ryokichi

1981-01-01

In this paper, the design study carried out since 1973 is outlined. The basic conceptual design was performed in fiscal 1973. In this design, concept was established on the total system of the experimental high temperature gas-cooled reactor including heat-utilizing system. The first conceptual design was carried out in fiscal 1974. The range of design was limited to the experimental reactor and its direct heat-removing system. The part 2 of the first conceptual design was performed in fiscal 1975, and the system design concerning the plant characteristics was made. The part 1 of the adjustment design was carried out in fiscal 1976, and the subject was the adjustment design of plant systems. The part 2 was performed in fiscal 1977, and the characteristics of plant control system were analyzed. In fiscal 1978, the analysis of flow characteristics in the core was made. The integrated system design was carried out in fiscal 1979, and the design of the total plant system except heat-utilizing system was started again. The part 1 of the detailed design was performed in fiscal 1980, and in addition, the possibility of increasing power output was examined. The construction cost of the experimental reactor plant estimated in 1979 was far higher than that in 1973. (Kako, I.)

Experimental study on ratcheting of a cylinder subjected to axially moving temperature distribution

International Nuclear Information System (INIS)

Igari, T.; Yamauchi, M.; Wada, H.

1989-01-01

Development of a design of cylinder subjected to axially moving temperature distribution is very important in the design of the reactor vessel of fast breeder reactor containing high-temperature sodium. So far, however, a mechanism and a prediction method for this ratcheting have not been clarified. This paper proposes the ratcheting mechanism as well as the predictive equations of the ratcheting strain for the representative two temperature distributions. The proposed ratcheting mechanism was based on the hoop-membrane stress-strain behavior of the cylinder, and the movement of the temperature distribution was regarded as a driving force of this ratcheting. This paper describes the results of the experimental study on the proposed ratcheting mechanism and the predictive equations

Knowledge of results and learning to tell the time in an adult male with an intellectual disability: a single-subject research design.

Science.gov (United States)

Applegate, Samantha L; Rice, Martin S; Stein, Franklin; Maitra, Kinsuk K

2008-01-01

The present study investigated whether knowledge of results, in the form of visual and audible feedback, would increase the accuracy of time-telling in an individual with an intellectual disability. A 19-year-old male with mild intellectual disability participated in this A1-B1-A2-B2 single-subject study design. The task involved correctly identifying the time given on a computer. Data, based on the Wilcoxon signed-rank test, showed that the participant demonstrated a greater number of correct responses during the intervention phases. Incorporating knowledge of results into a learning strategy for this individual with intellectual disability resulted in an increased ability to accurately identify the correct time on an analogue clock. There is a need to replicate the study design to increase the external validity and generalization of results. The strategies described in the present study may also be useful for occupational therapists who teach individuals with intellectual disability to gain skills in their everyday activities of daily living (ADLs). (c) 2007 John Wiley & Sons, Ltd.

Behavior of single lap composite bolted joint under traction loading: Experimental investigation

Science.gov (United States)

Awadhani, L. V.; Bewoor, Anand

2018-04-01

Composite bolted joints are preferred connection in the composite structures to facilitate the dismantling for the replacements/ maintenance work. The joint behavior under tractive forces has been studied in order to understand the safety of the structure designed. The main objective of this paper is to investigate the behavior of single-lap joints in carbon fiber reinforced epoxy composites under traction loading conditions. The experiments were designed to identify the effect of bolt diameter, stacking sequence and loading rate on the properties of the joint. The experimental results show that the parameters influence the joint performance significantly.

Comparing Single Case Design Overlap-Based Effect Size Metrics from Studies Examining Speech Generating Device Interventions

Science.gov (United States)

Chen, Mo; Hyppa-Martin, Jolene K.; Reichle, Joe E.; Symons, Frank J.

2016-01-01

Meaningfully synthesizing single case experimental data from intervention studies comprised of individuals with low incidence conditions and generating effect size estimates remains challenging. Seven effect size metrics were compared for single case design (SCD) data focused on teaching speech generating device use to individuals with…

Quasi experimental designs in pharmacist intervention research.

Science.gov (United States)

Krass, Ines

2016-06-01

Background In the field of pharmacist intervention research it is often difficult to conform to the rigorous requirements of the "true experimental" models, especially the requirement of randomization. When randomization is not feasible, a practice based researcher can choose from a range of "quasi-experimental designs" i.e., non-randomised and at time non controlled. Objective The aim of this article was to provide an overview of quasi-experimental designs, discuss their strengths and weaknesses and to investigate their application in pharmacist intervention research over the previous decade. Results In the literature quasi experimental studies may be classified into five broad categories: quasi-experimental design without control groups; quasi-experimental design that use control groups with no pre-test; quasi-experimental design that use control groups and pre-tests; interrupted time series and stepped wedge designs. Quasi-experimental study design has consistently featured in the evolution of pharmacist intervention research. The most commonly applied of all quasi experimental designs in the practice based research literature are the one group pre-post-test design and the non-equivalent control group design i.e., (untreated control group with dependent pre-tests and post-tests) and have been used to test the impact of pharmacist interventions in general medications management as well as in specific disease states. Conclusion Quasi experimental studies have a role to play as proof of concept, in the pilot phases of interventions when testing different intervention components, especially in complex interventions. They serve to develop an understanding of possible intervention effects: while in isolation they yield weak evidence of clinical efficacy, taken collectively, they help build a body of evidence in support of the value of pharmacist interventions across different practice settings and countries. However, when a traditional RCT is not feasible for

An Empirical Study of Parameter Estimation for Stated Preference Experimental Design

Directory of Open Access Journals (Sweden)

Fei Yang

2014-01-01

Full Text Available The stated preference experimental design can affect the reliability of the parameters estimation in discrete choice model. Some scholars have proposed some new experimental designs, such as D-efficient, Bayesian D-efficient. But insufficient empirical research has been conducted on the effectiveness of these new designs and there has been little comparative analysis of the new designs against the traditional designs. In this paper, a new metro connecting Chengdu and its satellite cities is taken as the research subject to demonstrate the validity of the D-efficient and Bayesian D-efficient design. Comparisons between these new designs and orthogonal design were made by the fit of model and standard deviation of parameters estimation; then the best model result is obtained to analyze the travel choice behavior. The results indicate that Bayesian D-efficient design works better than D-efficient design. Some of the variables can affect significantly the choice behavior of people, including the waiting time and arrival time. The D-efficient and Bayesian D-efficient design for MNL can acquire reliability result in ML model, but the ML model cannot develop the theory advantages of these two designs. Finally, the metro can handle over 40% passengers flow if the metro will be operated in the future.

Experimental design a chemometric approach

CERN Document Server

Deming, SN

1987-01-01

Now available in a paperback edition is a book which has been described as ``...an exceptionally lucid, easy-to-read presentation... would be an excellent addition to the collection of every analytical chemist. I recommend it with great enthusiasm.'' (Analytical Chemistry). Unlike most current textbooks, it approaches experimental design from the point of view of the experimenter, rather than that of the statistician. As the reviewer in `Analytical Chemistry' went on to say: ``Deming and Morgan should be given high praise for bringing the principles of experimental design to the level of the p

Evaluating statistical and clinical significance of intervention effects in single-case experimental designs: an SPSS method to analyze univariate data.

Science.gov (United States)

Maric, Marija; de Haan, Else; Hogendoorn, Sanne M; Wolters, Lidewij H; Huizenga, Hilde M

2015-03-01

Single-case experimental designs are useful methods in clinical research practice to investigate individual client progress. Their proliferation might have been hampered by methodological challenges such as the difficulty applying existing statistical procedures. In this article, we describe a data-analytic method to analyze univariate (i.e., one symptom) single-case data using the common package SPSS. This method can help the clinical researcher to investigate whether an intervention works as compared with a baseline period or another intervention type, and to determine whether symptom improvement is clinically significant. First, we describe the statistical method in a conceptual way and show how it can be implemented in SPSS. Simulation studies were performed to determine the number of observation points required per intervention phase. Second, to illustrate this method and its implications, we present a case study of an adolescent with anxiety disorders treated with cognitive-behavioral therapy techniques in an outpatient psychotherapy clinic, whose symptoms were regularly assessed before each session. We provide a description of the data analyses and results of this case study. Finally, we discuss the advantages and shortcomings of the proposed method. Copyright © 2014. Published by Elsevier Ltd.

Chemical-Based Formulation Design: Virtual Experimentation

DEFF Research Database (Denmark)

Conte, Elisa; Gani, Rafiqul

This paper presents a software, the virtual Product-Process Design laboratory (virtual PPD-lab) and the virtual experimental scenarios for design/verification of consumer oriented liquid formulated products where the software can be used. For example, the software can be employed for the design......, the additives and/or their mixtures (formulations). Therefore, the experimental resources can focus on a few candidate product formulations to find the best product. The virtual PPD-lab allows various options for experimentations related to design and/or verification of the product. For example, the selection...... design, model adaptation). All of the above helps to perform virtual experiments by blending chemicals together and observing their predicted behaviour. The paper will highlight the application of the virtual PPD-lab in the design and/or verification of different consumer products (paint formulation...

HAMMLAB 1999 experimental control room: design - design rationale - experiences

International Nuclear Information System (INIS)

Foerdestroemmen, N. T.; Meyer, B. D.; Saarni, R.

1999-01-01

A presentation of HAMMLAB 1999 experimental control room, and the accumulated experiences gathered in the areas of design and design rationale as well as user experiences. It is concluded that HAMMLAB 1999 experimental control room is a realistic, compact and efficient control room well suited as an Advanced NPP Control Room (ml)

Single Subject Prediction of Brain Disorders in Neuroimaging: Promises and Pitfalls

Science.gov (United States)

Arbabshirani, Mohammad R.; Plis, Sergey; Sui, Jing; Calhoun, Vince D.

2016-01-01

Neuroimaging-based single subject prediction of brain disorders has gained increasing attention in recent years. Using a variety of neuroimaging modalities such as structural, functional and diffusion MRI, along with machine learning techniques, hundreds of studies have been carried out for accurate classification of patients with heterogeneous mental and neurodegenerative disorders such as schizophrenia and Alzheimer's disease. More than 500 studies have been published during the past quarter century on single subject prediction focused on a multiple brain disorders. In the first part of this study, we provide a survey of more than 200 reports in this field with a focus on schizophrenia, mild cognitive impairment (MCI), Alzheimer's disease (AD), depressive disorders, autism spectrum disease (ASD) and attention-deficit hyperactivity disorder (ADHD). Detailed information about those studies such as sample size, type and number of extracted features and reported accuracy are summarized and discussed. To our knowledge, this is by far the most comprehensive review of neuroimaging-based single subject prediction of brain disorders. In the second part, we present our opinion on major pitfalls of those studies from a machine learning point of view. Common biases are discussed and suggestions are provided. Moreover, emerging trends such as decentralized data sharing, multimodal brain imaging, differential diagnosis, disease subtype classification and deep learning are also discussed. Based on this survey, there are extensive evidences showing the great potential of neuroimaging data for single subject prediction of various disorders. However, the main bottleneck of this exciting field is still the limited sample size, which could be potentially addressed by modern data sharing models such as the ones discussed in this paper. Emerging big data technologies and advanced data-intensive machine learning methodologies such as deep learning have coincided with an increasing need

Development and Validation of a Rubric for Diagnosing Students' Experimental Design Knowledge and Difficulties.

Science.gov (United States)

Dasgupta, Annwesa P; Anderson, Trevor R; Pelaez, Nancy

2014-01-01

It is essential to teach students about experimental design, as this facilitates their deeper understanding of how most biological knowledge was generated and gives them tools to perform their own investigations. Despite the importance of this area, surprisingly little is known about what students actually learn from designing biological experiments. In this paper, we describe a rubric for experimental design (RED) that can be used to measure knowledge of and diagnose difficulties with experimental design. The development and validation of the RED was informed by a literature review and empirical analysis of undergraduate biology students' responses to three published assessments. Five areas of difficulty with experimental design were identified: the variable properties of an experimental subject; the manipulated variables; measurement of outcomes; accounting for variability; and the scope of inference appropriate for experimental findings. Our findings revealed that some difficulties, documented some 50 yr ago, still exist among our undergraduate students, while others remain poorly investigated. The RED shows great promise for diagnosing students' experimental design knowledge in lecture settings, laboratory courses, research internships, and course-based undergraduate research experiences. It also shows potential for guiding the development and selection of assessment and instructional activities that foster experimental design. © 2014 A. P. Dasgupta et al. CBE—Life Sciences Education © 2014 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

Experimental Design for Hanford Low-Activity Waste Glasses with High Waste Loading

International Nuclear Information System (INIS)

Piepel, Gregory F.; Cooley, Scott K.; Vienna, John D.; Crum, Jarrod V.

2015-01-01

This report discusses the development of an experimental design for the initial phase of the Hanford low-activity waste (LAW) enhanced glass study. This report is based on a manuscript written for an applied statistics journal. Appendices A, B, and E include additional information relevant to the LAW enhanced glass experimental design that is not included in the journal manuscript. The glass composition experimental region is defined by single-component constraints (SCCs), linear multiple-component constraints (MCCs), and a nonlinear MCC involving 15 LAW glass components. Traditional methods and software for designing constrained mixture experiments with SCCs and linear MCCs are not directly applicable because of the nonlinear MCC. A modification of existing methodology to account for the nonlinear MCC was developed and is described in this report. One of the glass components, SO 3 , has a solubility limit in glass that depends on the composition of the balance of the glass. A goal was to design the experiment so that SO 3 would not exceed its predicted solubility limit for any of the experimental glasses. The SO 3 solubility limit had previously been modeled by a partial quadratic mixture model expressed in the relative proportions of the 14 other components. The partial quadratic mixture model was used to construct a nonlinear MCC in terms of all 15 components. In addition, there were SCCs and linear MCCs. This report describes how a layered design was generated to (i) account for the SCCs, linear MCCs, and nonlinear MCC and (ii) meet the goals of the study. A layered design consists of points on an outer layer, and inner layer, and a center point. There were 18 outer-layer glasses chosen using optimal experimental design software to augment 147 existing glass compositions that were within the LAW glass composition experimental region. Then 13 inner-layer glasses were chosen with the software to augment the existing and outer-layer glasses. The experimental

Experimental design optimisation: theory and application to estimation of receptor model parameters using dynamic positron emission tomography

International Nuclear Information System (INIS)

Delforge, J.; Syrota, A.; Mazoyer, B.M.

1989-01-01

General framework and various criteria for experimental design optimisation are presented. The methodology is applied to estimation of receptor-ligand reaction model parameters with dynamic positron emission tomography data. The possibility of improving parameter estimation using a new experimental design combining an injection of the β + -labelled ligand and an injection of the cold ligand is investigated. Numerical simulations predict remarkable improvement in the accuracy of parameter estimates with this new experimental design and particularly the possibility of separate estimations of the association constant (k +1 ) and of receptor density (B' max ) in a single experiment. Simulation predictions are validated using experimental PET data in which parameter uncertainties are reduced by factors ranging from 17 to 1000. (author)

A comparison of the effects of visual deprivation and regular body weight support treadmill training on improving over-ground walking of stroke patients: a multiple baseline single subject design.

Science.gov (United States)

Kim, Jeong-Soo; Kang, Sun-Young; Jeon, Hye-Seon

2015-01-01

The body-weight-support treadmill (BWST) is commonly used for gait rehabilitation, but other forms of BWST are in development, such as visual-deprivation BWST (VDBWST). In this study, we compare the effect of VDBWST training and conventional BWST training on spatiotemporal gait parameters for three individuals who had hemiparetic strokes. We used a single-subject experimental design, alternating multiple baselines across the individuals. We recruited three individuals with hemiparesis from stroke; two on the left side and one on the right. For the main outcome measures we assessed spatiotemporal gait parameters using GAITRite, including: gait velocity; cadence; step time of the affected side (STA); step time of the non-affected side (STN); step length of the affected side (SLA); step length of the non-affected side (SLN); step-time asymmetry (ST-asymmetry); and step-length asymmetry (SL-asymmetry). Gait velocity, cadence, SLA, and SLN increased from baseline after both interventions, but STA, ST-asymmetry, and SL-asymmetry decreased from the baseline after the interventions. The VDBWST was significantly more effective than the BWST for increasing gait velocity and cadence and for decreasing ST-asymmetry. VDBWST is more effective than BWST for improving gait performance during the rehabilitation for ground walking.

Experimental evaluation of the buckling phenomena in the new joint design for upper deck structure of a bridge

Directory of Open Access Journals (Sweden)

Solazzi L.

2010-06-01

Full Text Available This paper is concerned with the experimental mechanical analysis of a new design of a joint for a main components of a upper deck of a road bridge. These components are subject to the compression state stress induced by the weight and the load acting on the road. Each upper deck of a bridge (positioned on each side of the bridge is composed by four tubular structures that must be joint each together. The joint must to take in to account many aspects, for example that the length of each component is not the same (because, obviously, there is a mechanical tolerance. This phenomena induce different compression stress on each component and so is very important non only the critical buckling load but also the post buckling behaviour of the structure. It is very important that if a single tubular structure reaches the critical load of instability, it still has load capacity . This is to avoid that, in the case where a column reaches the instability, the entire load acting on a column increase the load on the remaining three. For this purpose many different geometrical solutions have been designed (elaborated by fem analyses and successively tested experimentally. This work reports the main experimental results on the best joint solution and how this increase the load capacity and the displacement respect to the solution without this flange.

The role of experimental typography in designing logotypes

OpenAIRE

Pogačnik, Tadeja

2014-01-01

Designing logotypes is an important part of graphic design. Great logotypes are designed using custom made typefaces. Therefore, it is very important, especially for the typographic designer, to have practical experience and be up to date with all trends in the field of experimental typefaces design, also called experimental typography. In my thesis statement, I carefully examined the problems of experimental typography - which allows more creative and free typography designing for different ...

Treatment of paranoid personality disorder with cognitive analytic therapy: a mixed methods single case experimental design.

Science.gov (United States)

Kellett, Stephen; Hardy, Gillian

2014-01-01

Paranoid personality disorder (PPD) presents as chronic and widespread interpersonal distrust, whereby the actions of others are interpreted as malevolent and malicious. This research details the assessment, formulation and treatment of a case of PPD within a 24-session contract of cognitive analytic therapy (CAT). The outcome methodology was an A/B with extended follow-up single case experimental design (SCED). The SCED was supplemented with qualitative patient interviewing via the Change Interview regarding their experience of CAT, whether change had taken place and detailing of any identified change mechanisms. Quantitative results show that five out of the six daily rated paranoia target complaint measures were extinguished during the treatment phase. Qualitatively, the patient attributed change to the therapy conducted. The results suggest that CAT was an effective intervention in this case of PPD and are discussed in terms of identified methodological shortcomings, treatment implications and the potential for generating a convincing evidence base for the psychotherapy of PPD. Narrative reformulation using a CAT model offers a key opportunity for the patient to achieve a new understanding of their paranoia. Psychotherapy for PPD requires a cognitive component, within a boundaried and relational therapy, that is able to reflect on paranoid enactments and ruptures within the therapeutic relationship.There is a large role for clinician-researchers in developing a PPD outcome evidence base. Copyright © 2013 John Wiley & Sons, Ltd.

Experimental design in chemistry: A tutorial.

Science.gov (United States)

Leardi, Riccardo

2009-10-12

In this tutorial the main concepts and applications of experimental design in chemistry will be explained. Unfortunately, nowadays experimental design is not as known and applied as it should be, and many papers can be found in which the "optimization" of a procedure is performed one variable at a time. Goal of this paper is to show the real advantages in terms of reduced experimental effort and of increased quality of information that can be obtained if this approach is followed. To do that, three real examples will be shown. Rather than on the mathematical aspects, this paper will focus on the mental attitude required by experimental design. The readers being interested to deepen their knowledge of the mathematical and algorithmical part can find very good books and tutorials in the references [G.E.P. Box, W.G. Hunter, J.S. Hunter, Statistics for Experimenters: An Introduction to Design, Data Analysis, and Model Building, John Wiley & Sons, New York, 1978; R. Brereton, Chemometrics: Data Analysis for the Laboratory and Chemical Plant, John Wiley & Sons, New York, 1978; R. Carlson, J.E. Carlson, Design and Optimization in Organic Synthesis: Second Revised and Enlarged Edition, in: Data Handling in Science and Technology, vol. 24, Elsevier, Amsterdam, 2005; J.A. Cornell, Experiments with Mixtures: Designs, Models and the Analysis of Mixture Data, in: Series in Probability and Statistics, John Wiley & Sons, New York, 1991; R.E. Bruns, I.S. Scarminio, B. de Barros Neto, Statistical Design-Chemometrics, in: Data Handling in Science and Technology, vol. 25, Elsevier, Amsterdam, 2006; D.C. Montgomery, Design and Analysis of Experiments, 7th edition, John Wiley & Sons, Inc., 2009; T. Lundstedt, E. Seifert, L. Abramo, B. Thelin, A. Nyström, J. Pettersen, R. Bergman, Chemolab 42 (1998) 3; Y. Vander Heyden, LC-GC Europe 19 (9) (2006) 469].

Experimental Design for Hanford Low-Activity Waste Glasses with High Waste Loading

Energy Technology Data Exchange (ETDEWEB)

Piepel, Gregory F. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Cooley, Scott K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Vienna, John D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Crum, Jarrod V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-07-24

This report discusses the development of an experimental design for the initial phase of the Hanford low-activity waste (LAW) enhanced glass study. This report is based on a manuscript written for an applied statistics journal. Appendices A, B, and E include additional information relevant to the LAW enhanced glass experimental design that is not included in the journal manuscript. The glass composition experimental region is defined by single-component constraints (SCCs), linear multiple-component constraints (MCCs), and a nonlinear MCC involving 15 LAW glass components. Traditional methods and software for designing constrained mixture experiments with SCCs and linear MCCs are not directly applicable because of the nonlinear MCC. A modification of existing methodology to account for the nonlinear MCC was developed and is described in this report. One of the glass components, SO₃, has a solubility limit in glass that depends on the composition of the balance of the glass. A goal was to design the experiment so that SO₃ would not exceed its predicted solubility limit for any of the experimental glasses. The SO₃ solubility limit had previously been modeled by a partial quadratic mixture model expressed in the relative proportions of the 14 other components. The partial quadratic mixture model was used to construct a nonlinear MCC in terms of all 15 components. In addition, there were SCCs and linear MCCs. This report describes how a layered design was generated to (i) account for the SCCs, linear MCCs, and nonlinear MCC and (ii) meet the goals of the study. A layered design consists of points on an outer layer, and inner layer, and a center point. There were 18 outer-layer glasses chosen using optimal experimental design software to augment 147 existing glass compositions that were within the LAW glass composition experimental region. Then 13 inner-layer glasses were chosen with the software to augment the existing and outer

Experimental and theoretical analysis for improved microscope design of optical projection tomographic microscopy.

Science.gov (United States)

Coe, Ryan L; Seibel, Eric J

2013-09-01

We present theoretical and experimental results of axial displacement of objects relative to a fixed condenser focal plane (FP) in optical projection tomographic microscopy (OPTM). OPTM produces three-dimensional, reconstructed images of single cells from two-dimensional projections. The cell rotates in a microcapillary to acquire projections from different perspectives where the objective FP is scanned through the cell while the condenser FP remains fixed at the center of the microcapillary. This work uses a combination of experimental and theoretical methods to improve the OPTM instrument design.

Chemicals-Based Formulation Design: Virtual Experimentations

DEFF Research Database (Denmark)

Conte, Elisa; Gani, Rafiqul

2011-01-01

This paper presents a systematic procedure for virtual experimentations related to the design of liquid formulated products. All the experiments that need to be performed when designing a liquid formulated product (lotion), such as ingredients selection and testing, solubility tests, property mea...... on the design of an insect repellent lotion will show that the software is an essential instrument in decision making, and that it reduces time and resources since experimental efforts can be focused on one or few product alternatives....

Pharmacokinetics of lansoprazole and its main metabolites after single intravenous doses in healthy Chinese subjects.

Science.gov (United States)

Zhang, Dan; Yang, Man; Liu, Man; Zhang, Yanan; Wang, Xiaolin; Xiao, Xue; Liu, Huichen

2012-11-01

The aim of the study was to evaluate the pharmacokinetics (PK) of lansoprazole (LPZ) and its main metabolites 5'-hydroxy lansoprazole (HLPZ) and lansoprazole sulphone (LPZS) after single intravenous (i.v.) doses of LPZ in healthy Chinese subjects, and the relationship between the cytochrome P450 (CYP) 2C19 phenotypes and the plasma concentrations of LPZS at the time-points in the elimination phase of LPZ. Twelve subjects were given lansoprazole by i.v. infusion. Blood samples were collected at designated time points up to 24 h. Plasma concentrations of LPZ, HLPZ and LPZS were quantified by a selective and sensitive liquid chromatography-tandem mass spectrometric (LC-MS/MS) method. After single i.v. doses of 15, 30 and 60 mg LPZ, C(max) and area under the plasma concentration-time curve (AUC(0-t)) of LPZ were 725 ± 151, 1480 ± 190, 3130 ± 480 µg · L(-1) and 1690 ± 1210, 3630 ± 2530, 8080 ± 4550 µg · h · L(-1), respectively. LPZ was generally well tolerated in healthy Chinese subjects, and displayed linear PK in the range of 15-60 mg. There were significant differences in the elimination of LPZ and the formation of LPZS between the single CYP2C19 poor metabolizer (PM) and the CYP2C19 extensive metabolizers (EM). The concentration of LPZS at the time-points in the elimination phase of LPZ could be monitored for CYP2C19 phenotyping. As a probe drug for CYP2C19 phenotyping, LPZ for injection might be more suitable than LPZ oral formulations.

Considering RNAi experimental design in parasitic helminths.

Science.gov (United States)

Dalzell, Johnathan J; Warnock, Neil D; McVeigh, Paul; Marks, Nikki J; Mousley, Angela; Atkinson, Louise; Maule, Aaron G

2012-04-01

Almost a decade has passed since the first report of RNA interference (RNAi) in a parasitic helminth. Whilst much progress has been made with RNAi informing gene function studies in disparate nematode and flatworm parasites, substantial and seemingly prohibitive difficulties have been encountered in some species, hindering progress. An appraisal of current practices, trends and ideals of RNAi experimental design in parasitic helminths is both timely and necessary for a number of reasons: firstly, the increasing availability of parasitic helminth genome/transcriptome resources means there is a growing need for gene function tools such as RNAi; secondly, fundamental differences and unique challenges exist for parasite species which do not apply to model organisms; thirdly, the inherent variation in experimental design, and reported difficulties with reproducibility undermine confidence. Ideally, RNAi studies of gene function should adopt standardised experimental design to aid reproducibility, interpretation and comparative analyses. Although the huge variations in parasite biology and experimental endpoints make RNAi experimental design standardization difficult or impractical, we must strive to validate RNAi experimentation in helminth parasites. To aid this process we identify multiple approaches to RNAi experimental validation and highlight those which we deem to be critical for gene function studies in helminth parasites.

Influences of crystallographic orientations on deformation mechanism and grain refinement of Al single crystals subjected to one-pass equal-channel angular pressing

International Nuclear Information System (INIS)

Han, W.Z.; Zhang, Z.F.; Wu, S.D.; Li, S.X.

2007-01-01

The influences of crystallographic orientations on the evolution of dislocation structures and the refinement process of sub-grains in Al single crystals processed by one-pass equal-channel angular pressing (ECAP) were systematically investigated by means of scanning electron microscopy, electron backscatter diffraction and transmission electron microscopy. Three single crystals with different orientations, denoted as crystal I, crystal II and crystal III, were specially designed according to the shape of the ECAP die. For crystal I, its insert direction is parallel to [1 1 0] and its extrusion direction is parallel to [1-bar11]. For crystal II, the (1-bar11) plane is located parallel to the intersection plane of the ECAP die, and the [1 1 0] direction is along the general shear direction on the intersection plane. For crystal III, the (1-bar11) plane is laid on the plane perpendicular to the intersection of the ECAP die, and the [1 1 0] direction is vertical to the general shear direction. For crystal I, abundant cell block structures with multi-slip characters were formed, and they should be induced by four symmetric slip systems, while for crystal II, there are two sets of sub-grain structures with higher misorientation, making an angle of ∼70 deg., which can be attributed to the interactions of the two asymmetric primary slip planes, whereas for crystal III, only one set of ribbon structures was parallel to the traces of (1-bar11) with the lowest misorientation angle among the three single crystals, which should result from the homogeneous slip on the primary slip plane. The different microstructural features of the three single crystals provide clear experimental evidence that the microstructures and misorientation evolution are strongly affected by the crystallographic orientation or by the interaction between shear deformation imposed by the ECAP die and the intrinsic slip deformation of the single crystals. Based on the experimental results and the

Experimental study of elementary collection efficiency of aerosols by spray: Design of the experimental device

Energy Technology Data Exchange (ETDEWEB)

Ducret, D.; Vendel, J.; Garrec. S.L.

1995-02-01

The safety of a nuclear power plant containment building, in which pressure and temperature could increase because of a overheating reactor accident, can be achieved by spraying water drops. The spray reduces the pressure and the temperature levels by condensation of steam on cold water drops. The more stringent thermodynamic conditions are a pressure of 5.10{sup 5} Pa (due to steam emission) and a temperature of 413 K. Moreover its energy dissipation function, the spray leads to the washout of fission product particles emitted in the reactor building atmosphere. The present study includes a large program devoted to the evaluation of realistic washout rates. The aim of this work is to develop experiments in order to determine the collection efficiency of aerosols by a single drop. To do this, the experimental device has to be designed with fundamental criteria:-Thermodynamic conditions have to be representative of post-accident atmosphere. Thermodynamic equilibrium has to be attained between the water drops and the gaseous phase. Thermophoretic, diffusiophoretic and mechanical effects have to be studied independently. Operating conditions have to be homogenous and constant during each experiment. This paper presents the design of the experimental device. In practice, the consequences on the design of each of the criteria given previously and the necessity of being representative of the real conditions will be described.

Pharmacokinetics of lansoprazole and its main metabolites after single and multiple intravenous doses in healthy Chinese subjects.

Science.gov (United States)

Zhang, Dan; Zhang, Yanan; Liu, Man; Wang, Xiaolin; Yang, Man; Han, Jing; Liu, Huichen

2013-09-01

The aim of the study was to evaluate and compare the pharmacokinetics of lansoprazole (LPZ) and its main metabolites, 5'-hydroxy lansoprazole (HLPZ) and lansoprazole sulfone (LPZS), after single and multiple intravenous (i.v.) doses of LPZ in healthy Chinese subjects. Twelve subjects (six males and six females) were given a single dose of LPZ by i.v. infusion on day 1, and multiple doses from day 2 to day 6. Blood samples were collected at designated time points for analysis of plasma concentrations of LPZ, HLPZ and LPZS by an LC-MS/MS method. LPZ was generally well tolerated in healthy Chinese subjects. After single and multiple i.v. doses of 30 mg LPZ, the C max values of LPZ, HLPZ and LPZS were 1490 ± 290 and 1450 ± 280, 175 ± 71 and 154 ± 56, and 51.3 ± 82.9 and 74.1 ± 158.7 ng/mL, with the AUC0-t values 3280 ± 2550 and 4260 ± 3880, 381 ± 128 and 389 ± 111, and 389 ± 1204 and 700 ± 2255 ng h/mL, respectively. The t 1/2 and CL values of LPZ after single and multiple i.v. doses were 1.48 ± 1.03 and 2.19 ± 1.03 h, and 11.67 ± 4.49 and 9.56 ± 4.08 L/h, respectively. Compared with the pharmacokinetics of LPZ after a single dose, t 1/2 increased markedly, CL decreased significantly and AUC increased by over 20 % after multiple doses. The results indicated that there was drug accumulation of LPZ after multiple i.v. doses, and there was no gender-related difference in pharmacokinetics of LPZ and its two metabolites.

An experimental vital signs detection radar using low-IF heterodyne architecture and single-sideband transmission

DEFF Research Database (Denmark)

Jensen, Brian Sveistrup; Johansen, Tom Keinicke; Yan, Lei

2013-01-01

In this paper an experimental X-band radar system, called DTU-VISDAM, developed for the detection and monitoring of human vital signs is described. The DTU-VISDAM radar exploits a low intermediate frequency (IF) heterodyne RF front-end architecture and single-sideband (SSB) transmission for easier...... and more reliable extraction of the vital signs. The hardware implementation of the proposed low-IF RF front-end architecture and associated IF circuitry is discussed. Furthermore, the signal processing and calibration steps necessary to extract the vital signs information measured on a human subject...

ENGINEERING DESIGN OPTIMIZATION OF HEEL TESTING EQUIPMENT IN THE EXPERIMENTAL VALIDATION OF SAFE WALKING

Directory of Open Access Journals (Sweden)

Cristiano Fragassa

2017-06-01

Full Text Available Experimental test methods for the evaluation of the resistance of heels of ladies' shoes in the case of impact loads are fully defined by International Organization for Standardization (ISO procedures that indicate all the conditions of experiment. A first Standard (ISO 19553 specifies the test method for determining the strength of the heels in the case of single impact. The result offers a valuation of the liability to fail under the sporadic heavy blows. A second Standard (ISO 19556 details a method for testing the capability of heels of women' shoes to survive to the repetition of small impacts provoked by normal walking. These Standards strictly define the features for two different testing devices (with specific materials, geometries, weights, etc. and all the experimental procedures to be followed during tests. On the contrary, this paper describes the technical solutions adopted to design one single experimental device able to perform impact testing of heels in both conditions. Joining the accuracy of mechanic movements with the speed of an electronic control system, a new and flexible equipment for the complete characterization of heels respect to (single or fatigue impacts was developed. Moreover a new level of performances in experimental validation of heel resistance was introduced by the versatility of the user-defined software control programs, able to encode every complex time-depending cycle of impact loads. Dynamic simulations permitted to investigate the impacts on heel in different conditions of testing, optimizing the machine design. The complexity of real stresses on shoes during an ordinary walk and in other common situations (as going up and downstairs was considered for a proper dimensioning.

Experimental Design: Review and Comment.

Science.gov (United States)

1984-02-01

creativity. Innovative modifications and extensions of classical experimental designs were developed and many useful articles were published in a short...Pjrazolone Industrielle ," Bulletin de la Soci~t6 Chimique de France, 11-12, 1171-1174. LI, K. C. (1983), "Minimaxity for Randomized Designs: Some

Design of Active Magnetic Bearing Controllers for Rotors Subjected to Gas Seal Forces

DEFF Research Database (Denmark)

Lauridsen, Jonas Skjødt; Santos, Ilmar F.

2018-01-01

Proper design of feedback controllers is crucial for ensuring high performance of Active Magnetic Bearing (AMB) supported rotor dynamic systems. Annular seals in those systems can contribute with significant forces, which, in many cases, are hard to model in advance due to complex geometries...... of the seal and multiphase fluids. Hence, it can be challenging to design AMB controllers that will guarantee robust performance for these kinds of systems. This paper demonstrates the design, simulation and experimental results of model based controllers for AMB systems, subjected to dynamic seal forces....... The controllers are found using H-infinity - and µ synthesis and are based on a global rotor dynamic model in-which the seal coefficients are identified in-situ. The controllers are implemented in a rotor-dynamic test facility with two radial AMBs and one annular seal with an adjustable inlet pressure. The seal...

Designation and Implementation of Microcomputer Principle and Interface Technology Virtual Experimental Platform Website

Science.gov (United States)

Gao, JinYue; Tang, Yin

This paper explicitly discusses the designation and implementation thought and method of Microcomputer Principle and Interface Technology virtual experimental platform website construction. The instructional design of this platform mainly follows with the students-oriented constructivism learning theory, and the overall structure is subject to the features of teaching aims, teaching contents and interactive methods. Virtual experiment platform production and development should fully take the characteristics of network operation into consideration and adopt relevant technologies to improve the effect and speed of network software application in internet.

Design study of toroidal magnets for tokamak experimental power reactors

International Nuclear Information System (INIS)

Stekly, Z.J.J.; Lucas, E.J.

1976-12-01

This report contains the results of a six-month study of superconducting toroidal field coils for a Tokamak Experimental Power Reactor to be built in the late 1980s. The designs are for 8 T and 12 T maximum magnetic field at the superconducting winding. At each field level two main concepts were generated; one in which each of the 16 coils comprising the system has an individual vacuum vessel and the other in which all the coils are contained in a single vacuum vessel. The coils have a D shape and have openings of 11.25 m x 7.5 m for the 8 T coils and 10.2 m x 6.8 m for the 12 T coils. All the designs utilize rectangular cabled conductor made from copper stabilized Niobium Titanium composite which operates at 4.2 K for the 8 T design and at 2.5 K for the 12 T design. Manufacturing procedures, processes and schedule estimates are also discussed

Performance of Single Friction Pendulum bearing for isolated buildings subjected to seismic actions in Vietnam

Science.gov (United States)

Nguyen, N. V.; Nguyen, C. H.; Hoang, H. P.; Huong, K. T.

2018-04-01

Using structural control technology in earthquake resistant design of buildings in Vietnam is very limited. In this paper, a performance evaluation of using Single Friction Pendulum (SFP) bearing for seismically isolated buildings with earthquake conditions in Vietnam is presented. A two-dimensional (2-D) model of the 5-storey building subjected to earthquakes is analyzed in time domain. Accordingly, the model is analyzed for 2 cases: with and without SFP bearing. The ground acceleration data is selected and scaled to suit the design acceleration in Hanoi followed by the Standard TCVN 9386:2012. It is shown that the seismically isolated buildings gets the performance objectives while achieving an 91% reduction in the base shear, a significant decrease in the inter-story drift and absolute acceleration of each story.

Optimal Bayesian Experimental Design for Combustion Kinetics

KAUST Repository

Huan, Xun

2011-01-04

Experimental diagnostics play an essential role in the development and refinement of chemical kinetic models, whether for the combustion of common complex hydrocarbons or of emerging alternative fuels. Questions of experimental design—e.g., which variables or species to interrogate, at what resolution and under what conditions—are extremely important in this context, particularly when experimental resources are limited. This paper attempts to answer such questions in a rigorous and systematic way. We propose a Bayesian framework for optimal experimental design with nonlinear simulation-based models. While the framework is broadly applicable, we use it to infer rate parameters in a combustion system with detailed kinetics. The framework introduces a utility function that reflects the expected information gain from a particular experiment. Straightforward evaluation (and maximization) of this utility function requires Monte Carlo sampling, which is infeasible with computationally intensive models. Instead, we construct a polynomial surrogate for the dependence of experimental observables on model parameters and design conditions, with the help of dimension-adaptive sparse quadrature. Results demonstrate the efficiency and accuracy of the surrogate, as well as the considerable effectiveness of the experimental design framework in choosing informative experimental conditions.

N-of-1-pathways MixEnrich: advancing precision medicine via single-subject analysis in discovering dynamic changes of transcriptomes.

Science.gov (United States)

Li, Qike; Schissler, A Grant; Gardeux, Vincent; Achour, Ikbel; Kenost, Colleen; Berghout, Joanne; Li, Haiquan; Zhang, Hao Helen; Lussier, Yves A

2017-05-24

Transcriptome analytic tools are commonly used across patient cohorts to develop drugs and predict clinical outcomes. However, as precision medicine pursues more accurate and individualized treatment decisions, these methods are not designed to address single-patient transcriptome analyses. We previously developed and validated the N-of-1-pathways framework using two methods, Wilcoxon and Mahalanobis Distance (MD), for personal transcriptome analysis derived from a pair of samples of a single patient. Although, both methods uncover concordantly dysregulated pathways, they are not designed to detect dysregulated pathways with up- and down-regulated genes (bidirectional dysregulation) that are ubiquitous in biological systems. We developed N-of-1-pathways MixEnrich, a mixture model followed by a gene set enrichment test, to uncover bidirectional and concordantly dysregulated pathways one patient at a time. We assess its accuracy in a comprehensive simulation study and in a RNA-Seq data analysis of head and neck squamous cell carcinomas (HNSCCs). In presence of bidirectionally dysregulated genes in the pathway or in presence of high background noise, MixEnrich substantially outperforms previous single-subject transcriptome analysis methods, both in the simulation study and the HNSCCs data analysis (ROC Curves; higher true positive rates; lower false positive rates). Bidirectional and concordant dysregulated pathways uncovered by MixEnrich in each patient largely overlapped with the quasi-gold standard compared to other single-subject and cohort-based transcriptome analyses. The greater performance of MixEnrich presents an advantage over previous methods to meet the promise of providing accurate personal transcriptome analysis to support precision medicine at point of care.

Single wire drift chamber design

International Nuclear Information System (INIS)

Krider, J.

1987-01-01

This report summarizes the design and prototype tests of single wire drift chambers to be used in Fermilab test beam lines. The goal is to build simple, reliable detectors which require a minimum of electronics. Spatial resolution should match the 300 μm rms resolution of the 1 mm proportional chambers that they will replace. The detectors will be used in beams with particle rates up to 20 KHz. Single track efficiency should be at least 99%. The first application will be in the MT beamline, which has been designed for calibration of CDF detectors. A set of four x-y modules will be used to track and measure the momentum of beam particles

Exploring multi-metal biosorption by indigenous metal-hyperresistant Enterobacter sp. J1 using experimental design methodologies

International Nuclear Information System (INIS)

Lu, W.-B.; Kao, W.-C.; Shi, J.-J.; Chang, J.-S.

2008-01-01

A novel experimental design, combining mixture design and response surface methodology (RSM), was developed to investigate the competitive adsorption behavior of lead, copper and cadmium by an indigenous isolate Enterobacter sp. J1 able to tolerate high concentrations of a variety of heavy metals. Using the proposed combinative experimental design, two different experiment designs in a ternary metal biosorption system can be integrated to a succinct experiment and the number of experimental trials was markedly reduced from 38 to 26 by reusing the mutual experimental data. Triangular contour diagrams and triangular three-dimensional surface plots were generated to describe the ternary metal biosorption equilibrium data in mixture design systems. The results show that the preference of metal sorption of Enterobacter sp. J1 decreased in the order of Pb 2+ > Cu 2+ > Cd 2+ . The presence of other metals resulted in a competitive effect. The influence of the other two metals in ternary metal biosorption system can be easily determined by comparing the stray distance from the single metal biosorption. The behavior of competitive biosorption was successfully described and predicted using a combined Langmuir-Freundlich model along with new three-dimensional contour-surface plots

Exploring multi-metal biosorption by indigenous metal-hyperresistant Enterobacter sp. J1 using experimental design methodologies

Energy Technology Data Exchange (ETDEWEB)

Lu, W.-B. [Department of Cosmetic Science, Chung Hwa University of Medical Technology, Tainan, Taiwan (China); Kao, W.-C.; Shi, J.-J. [Department of Chemical Engineering, National Cheng Kung University, Tainan, Taiwan (China); Chang, J.-S. [Department of Chemical Engineering, National Cheng Kung University, Tainan, Taiwan (China)], E-mail: changjs@mail.ncku.edu.tw

2008-05-01

A novel experimental design, combining mixture design and response surface methodology (RSM), was developed to investigate the competitive adsorption behavior of lead, copper and cadmium by an indigenous isolate Enterobacter sp. J1 able to tolerate high concentrations of a variety of heavy metals. Using the proposed combinative experimental design, two different experiment designs in a ternary metal biosorption system can be integrated to a succinct experiment and the number of experimental trials was markedly reduced from 38 to 26 by reusing the mutual experimental data. Triangular contour diagrams and triangular three-dimensional surface plots were generated to describe the ternary metal biosorption equilibrium data in mixture design systems. The results show that the preference of metal sorption of Enterobacter sp. J1 decreased in the order of Pb{sup 2+} > Cu{sup 2+} > Cd{sup 2+}. The presence of other metals resulted in a competitive effect. The influence of the other two metals in ternary metal biosorption system can be easily determined by comparing the stray distance from the single metal biosorption. The behavior of competitive biosorption was successfully described and predicted using a combined Langmuir-Freundlich model along with new three-dimensional contour-surface plots.

Experimental study of micro-milling mechanism and surface quality of a nickel-based single crystal superalloy

Energy Technology Data Exchange (ETDEWEB)

Gao, Qi; Gong, Yadong; Zhou, Yun Guang; Wen, Xue Long [School of Mechanical Engineering and Automation, Northeastern University, Shenyang (China)

2017-01-15

Micro-milling is widely used as a method for machining of micro-parts with high precision and efficiency. Taking the nickel-based single-crystal superalloy DD98 as the research object, the crystal characteristics of single-crystal materials were analysed, and the removal mechanism of single-crystal micro-milled parts was described. Based on molecular dynamics, a simulation model for nickel-based single-crystal superalloy DD98 micro-milling was established. Based on the response surface method of central composite design, the influences of spindle speed, feed rate, and milling depth on the surface roughness were examined, and a second-order regression model of the DD98 surface roughness was established. Using analysis of variance and the residuals of the model, a significant influence on surface roughness was found in the following order from large to small: Feed rate, spindle speed, and milling depth. Comparisons were conducted between the micro-milling experimental values and the predicted model values for different process parameters. The results show that the model fit is relatively high, and the adaptability is good. Scanning electron microscopy analysis of the micro-milling surfaces was performed to verify the slip and the removal mechanism of single-crystal materials. These results offer a theoretical reference and experimental basis for micro-milling of single-crystal materials.

Single Phase Current-Source Active Rectifier for Traction: Control System Design and Practical Problems

Directory of Open Access Journals (Sweden)

Jan Michalik

2006-01-01

Full Text Available This research has been motivated by industrial demand for single phase current-source active rectifier dedicated for reconstruction of older types of dc machine locomotives. This paper presents converters control structure design and simulations. The proposed converter control is based on the mathematical model and due to possible interaction with railway signaling and required low switching frequency employs synchronous PWM. The simulation results are verified by experimental tests performed on designed laboratory prototype of power of 7kVA

Conceptual design study of fusion experimental reactor (FY86 FER)

International Nuclear Information System (INIS)

Kobayashi, Takeshi; Yamada, Masao; Mizoguchi, Tadanori

1987-09-01

This report describes the results of the reactor configuration/structure design for the fusion experimental reactor (FER) performed in FY 1986. The design was intended to meet the physical and engineering mission of the next step device which was decided by the subcommittee on the next step device of the nuclear fusion council. The objectives of the design study in FY 1986 are to advance and optimize the design concept of the last year because the recommendation of the subcommittee was basically the same as the design philosophy of the last year. Six candidate reactor configurations which correspond to options C ∼ D presented by the subcommittee were extensively examined. Consequently, ACS reactor (Advanced Option-C with Single Null Divertor) was selected as the reference configuration from viewpoints of technical risks and cost performance. Regarding the reactor structure, the following items were investigated intensively: minimization of reactor size, protection of first wall against plasma disruption, simplification of shield structure, reactor configuration which enables optimum arrangement of poloidal field coils. (author)

Sequential experimental design based generalised ANOVA

Energy Technology Data Exchange (ETDEWEB)

Chakraborty, Souvik, E-mail: csouvik41@gmail.com; Chowdhury, Rajib, E-mail: rajibfce@iitr.ac.in

2016-07-15

Over the last decade, surrogate modelling technique has gained wide popularity in the field of uncertainty quantification, optimization, model exploration and sensitivity analysis. This approach relies on experimental design to generate training points and regression/interpolation for generating the surrogate. In this work, it is argued that conventional experimental design may render a surrogate model inefficient. In order to address this issue, this paper presents a novel distribution adaptive sequential experimental design (DA-SED). The proposed DA-SED has been coupled with a variant of generalised analysis of variance (G-ANOVA), developed by representing the component function using the generalised polynomial chaos expansion. Moreover, generalised analytical expressions for calculating the first two statistical moments of the response, which are utilized in predicting the probability of failure, have also been developed. The proposed approach has been utilized in predicting probability of failure of three structural mechanics problems. It is observed that the proposed approach yields accurate and computationally efficient estimate of the failure probability.

Cost Optimal Design of a Single-Phase Dry Power Transformer

Directory of Open Access Journals (Sweden)

Raju Basak

2015-08-01

Full Text Available The Dry type transformers are preferred to their oil-immersed counterparts for various reasons, particularly because their operation is hazardless. The application of dry transformers was limited to small ratings in the earlier days. But now these are being used for considerably higher ratings.  Therefore, their cost-optimal design has gained importance. This paper deals with the design procedure for achieving cost optimal design of a dry type single-phase power transformer of small rating, subject to usual design constraints on efficiency and voltage regulation. The selling cost for the transformer has been taken as the objective function. Only two key variables have been chosen, the turns/volt and the height: width ratio of window, which affects the cost function to high degrees. Other variables have been chosen on the basis of designers’ experience. Copper has been used as conductor material and CRGOS as core material to achieve higher efficiency, lower running cost and compact design. The electrical and magnetic loadings have been kept at their maximum values without violating the design constraints. The optimal solution has been obtained by the method of exhaustive search using nested loops.

Pen needle design influences ease of insertion, pain, and skin trauma in subjects with type 2 diabetes

DEFF Research Database (Denmark)

Præstmark, Kezia A; Jensen, Morten L; Berg Madsen, Nils

2016-01-01

subject and in random order. Penetration force (PF) through the skin, pain perception on 100 mm visual analog scale, and change in skin blood perfusion (SBP) were quantified after the insertions. RESULTS: Needle diameter was positively related to PF and SBP (ptrend relation...... of insertion, pain and skin trauma. RESEARCH DESIGN AND METHODS: 30 subjects with injection-treated type 2 diabetes and body mass index 25-35 kg/m(2) were included in the single-blinded study. Each subject received abdominal insertions with 18 different types of needles. All needles were tested twice per....... Lack of needle lubrication and small 'needle hooks' increased PF and SBP (pskin and in polyurethane rubber were linearly related, and pain outcome...

A quasi-experimental design based on regional variations: discussion of a method for evaluating outcomes of medical practice

DEFF Research Database (Denmark)

Loft, A; Andersen, T F; Madsen, Mette

1989-01-01

A large proportion of common medical practices are subject to substantial regional variation resulting in numerous natural experiments. Opportunities are thereby provided for outcome evaluation through quasi-experimental design. If patients treated in different regions were comparable a natural...... experiment involving alternative treatments could be regarded as 'pseudo randomised', but empirical investigations are needed to verify this prerequisite. This paper discusses the role of quasi-experimental designs in assessment of medical care with evaluation of outcomes after hysterectomy in Denmark...... groups are elicited from administrative data. We conclude that it is possible to establish a quasi-experimental design based on regional variations and that the comparability of the groups included may be assessed through registry data. The importance of technology diffusion for the prospects...

Single- and multiple-dose pharmacokinetics, pharmacodynamics, and safety of apixaban in healthy Chinese subjects

Directory of Open Access Journals (Sweden)

Cui Y

2013-12-01

Full Text Available Yimin Cui,1 Yan Song,2 Jessie Wang,2 Zhigang Yu,2 Alan Schuster,2 Yu Chen Barrett,2 Charles Frost2 1Peking University First Hospital, Beijing, People's Republic of China; 2Bristol-Myers Squibb, Princeton, NJ, USA Background: The pharmacokinetics (PK, pharmacodynamics (PD, and safety of apixaban were assessed in healthy Chinese subjects in this randomized, placebo-controlled, double-blind, single-sequence, single- and multiple-dose study. Subjects and methods: Eighteen subjects 18–45 years of age were randomly assigned (2:1 ratio to receive apixaban or matched placebo. Subjects received a single 10 mg dose of apixaban or placebo on day 1, followed by 10 mg apixaban or placebo twice daily for 6 days (days 4–9. The PK and PD of apixaban were assessed by collecting plasma samples for 72 hours following the dose on day 1 and the morning dose on day 9, and measuring apixaban concentration and anti-Xa activity. Safety was assessed via physical examinations, vital sign measurements, electrocardiograms, and clinical laboratory evaluations. Results: PK analysis showed similar characteristics of apixaban after single and multiple doses, including a median time to maximum concentration of ~3 hours, mean elimination half-life of ~11 hours, and renal clearance of ~1.2 L/hour. The accumulation index was 1.7, consistent with twice-daily dosing and the observed elimination half-life. Single-dose data predict multiple-dose PK, therefore apixaban PK are time-independent. The relationship between anti-Xa activity and plasma apixaban concentrations appears to be linear. Apixaban was safe and well tolerated, with no bleeding-related adverse events reported. Conclusion: Apixaban was safe and well tolerated in healthy Chinese subjects. Apixaban PK and PD were predictable and consistent with findings from previous studies in Asian and non-Asian subjects. The administration of apixaban does not require any dose modification based on race. Keywords: apixaban, oral

experimental implementation of single-phase, three-level, sinusoidal

African Journals Online (AJOL)

Page 1 ... of many multilevel inverter configurations. This paper presents an experimental report of a simplified topology for single-phase, SPWM, three-level voltage source inverter wit R-L load. To keep the power circuit ... employed in many industrial applications such as variable speed drives, uninterruptible power sup-.

A Theory-Driven Approach to Subject Design in Teacher Education

Science.gov (United States)

Zundans-Fraser, Lucia; Auhl, Greg

2016-01-01

The intent of this study was to examine how a theoretically-designed subject in an undergraduate teacher education course impacted on the learning and confidence of pre-service teachers in catering for the needs of students with diverse needs. The subject design utilised theoretical principles of self-organisation that were incorporated with the…

Pharmacokinetic Effects of Antidrug Antibodies Occurring in Healthy Subjects After a Single Dose of Intravenous Infliximab.

Science.gov (United States)

Ehrenpreis, Eli D

2017-12-01

Infliximab pharmacokinetic studies have been performed in patients receiving chronic infliximab therapy. In these patients, infliximab antidrug antibodies (ADAs) increase infliximab clearance and decrease serum levels and drug efficacy. This study analyzed the pharmacokinetic effect of infliximab ADAs in healthy subjects receiving a single dose of intravenous infliximab. Data were obtained from a single-blind, parallel-group, single-dose study of healthy subjects receiving 5 mg/kg of intravenous SB2 (infliximab biosimilar), EU-sourced Remicade (EU-IFX) or US-sourced Remicade (US-IFX). Serum infliximab was measured at 1, 2, 3, 6, 12, 24, 48, and 72 h and at 5, 7, 14, 21, 28, 42, 56, and 70 days after administration. ADAs were measured pre-dose and at 29 and 71 days. Data from the first ten subjects randomized to each treatment arm were utilized for this study. A two-compartment model of the serum infliximab vs. time curve was developed using nonlinear regression. At 10 weeks, 11 subjects (37%) developed ADAs. ADAs were detected in four subjects after SB2, one subject after EU-IFX, and six subjects after US-IFX infusion. Of these, neutralizing antibodies occurred in one subject after SB2, in no subjects after EU-IFX, and in three subjects after US-IFX infusion. Infliximab clearance was increased in subjects with ADAs vs. those without ADAs (12.89 ± 2.69 vs. 9.90 ± 1.74 ml/h; p ADAs (282.4 ± 56.4 vs. 343.3 ± 61.9 h; p ADAs are common in healthy subjects after a single intravenous dose of infliximab and result in faster infliximab clearance, shorter elimination time, and lower serum infliximab levels. These data confirm that ADAs are common with biologic therapy and significantly impact the efficacy of these drugs.

Esthetic Evaluation of Anterior Single-Tooth Implants with Different Abutment Designs - Patients' Satisfaction Compared to Dentists' Observations

NARCIS (Netherlands)

Patil, Ratnadeep; Gresnigt, Marco M M; Mahesh, Kavita; Dilbaghi, Anjali; Cune, Marco S

Purpose: To correlate patients' satisfaction and dentists' observations regarding two abutment designs used for single crowns in the esthetic zone: a divergent one (control) and a curved one (experimental), with special emphasis on muco-gingival esthetics. Materials and Methods: Twenty-six patients

Experimental study and numerical simulation of the plastic deformation of zirconium single crystals

International Nuclear Information System (INIS)

Lebon, C.

2011-01-01

There is only few experimental data in the literature on the zirconium single crystals and no constitutive laws for this single crystal material are provided. The goal of this work is then to create an experimental database like the Critical Resolved Shear Stress (CRSS) for the prismatic slip, the strain-hardening, the activation of the prismatic glide system and the activation volumes. We determine theses parameters from image correlation method. Then, we develop a new multi-scale approach using dislocations dynamics concept and finite element computations. Finally, a first single crystal constitutive law for the zirconium is proposed and a good agreement with the experimental data is obtained. (author) [fr

Constructing experimental designs for discrete-choice experiments: report of the ISPOR Conjoint Analysis Experimental Design Good Research Practices Task Force.

Science.gov (United States)

Reed Johnson, F; Lancsar, Emily; Marshall, Deborah; Kilambi, Vikram; Mühlbacher, Axel; Regier, Dean A; Bresnahan, Brian W; Kanninen, Barbara; Bridges, John F P

2013-01-01

Stated-preference methods are a class of evaluation techniques for studying the preferences of patients and other stakeholders. While these methods span a variety of techniques, conjoint-analysis methods-and particularly discrete-choice experiments (DCEs)-have become the most frequently applied approach in health care in recent years. Experimental design is an important stage in the development of such methods, but establishing a consensus on standards is hampered by lack of understanding of available techniques and software. This report builds on the previous ISPOR Conjoint Analysis Task Force Report: Conjoint Analysis Applications in Health-A Checklist: A Report of the ISPOR Good Research Practices for Conjoint Analysis Task Force. This report aims to assist researchers specifically in evaluating alternative approaches to experimental design, a difficult and important element of successful DCEs. While this report does not endorse any specific approach, it does provide a guide for choosing an approach that is appropriate for a particular study. In particular, it provides an overview of the role of experimental designs for the successful implementation of the DCE approach in health care studies, and it provides researchers with an introduction to constructing experimental designs on the basis of study objectives and the statistical model researchers have selected for the study. The report outlines the theoretical requirements for designs that identify choice-model preference parameters and summarizes and compares a number of available approaches for constructing experimental designs. The task-force leadership group met via bimonthly teleconferences and in person at ISPOR meetings in the United States and Europe. An international group of experimental-design experts was consulted during this process to discuss existing approaches for experimental design and to review the task force's draft reports. In addition, ISPOR members contributed to developing a consensus

Optimized design and performance of a shared pump single clad 2 μm TDFA

Science.gov (United States)

Tench, Robert E.; Romano, Clément; Delavaux, Jean-Marc

2018-05-01

We report the design, experimental performance, and simulation of a single stage, co- and counter-pumped Tm-doped fiber amplifier (TDFA) in the 2 μm signal wavelength band with an optimized 1567 nm shared pump source. We investigate the dependence of output power, gain, and efficiency on pump coupling ratio and signal wavelength. Small signal gains of >50 dB, an output power of 2 W, and small signal noise figures of performance agree well with the experimental data. We also discuss performance tradeoffs with respect to amplifier topology for this simple and efficient TDFA.

Experimental and analytical parametric study of single-crystal unimorph beams for vibration energy harvesting.

Science.gov (United States)

Karami, M Amin; Bilgen, Onur; Inman, Daniel J; Friswell, Michael I

2011-07-01

This research presents an experimental and theoretical energy harvesting characterization of beam-like, uniform cross-section, unimorph structures employing single-crystal piezoelectrics. Different piezoelectric materials, substrates, and configurations are examined to identify the best design configuration for lightweight energy harvesting devices for low-power applications. Three types of piezoelectrics (singlecrystal PMN-PZT, polycrystalline PZT-5A, and PZT-5H-type monolithic ceramics) are evaluated in a unimorph cantilevered beam configuration. The devices have been excited by harmonic base acceleration. All of the experimental characteristics have been used to validate an exact electromechanical model of the harvester. The study shows the optimum choice of substrate material for single-crystal piezoelectric energy harvesting. Comparison of energy scavengers with stainless steel substrates reveals that single-crystal harvesters produce superior power compared with polycrystalline devices. To further optimize the power harvesting, we study the relation between the thickness of the substrate and the power output for different substrate materials. The relation between power and substrate thickness profoundly varies among different substrate materials. The variation is understood by examining the change of mechanical transmissibility and the variations of the coupling figure of merit of the harvesters with thickness ratio. The investigation identifies the optimal thickness of the substrate for different substrate materials. The study also shows that the densities of the substrates and their mechanical damping coefficients have significant effects on the power output.

Experimental design research approaches, perspectives, applications

CERN Document Server

Stanković, Tino; Štorga, Mario

2016-01-01

This book presents a new, multidisciplinary perspective on and paradigm for integrative experimental design research. It addresses various perspectives on methods, analysis and overall research approach, and how they can be synthesized to advance understanding of design. It explores the foundations of experimental approaches and their utility in this domain, and brings together analytical approaches to promote an integrated understanding. The book also investigates where these approaches lead to and how they link design research more fully with other disciplines (e.g. psychology, cognition, sociology, computer science, management). Above all, the book emphasizes the integrative nature of design research in terms of the methods, theories, and units of study—from the individual to the organizational level. Although this approach offers many advantages, it has inherently led to a situation in current research practice where methods are diverging and integration between individual, team and organizational under...

The reactor safety study of experimental multi-purpose VHTR design

International Nuclear Information System (INIS)

Yasuno, T.; Mitake, S.; Ezaki, M.; Suzuki, K.

1981-01-01

Over the past years, the design works of the Experimental Very High Temperature Reactor (VHTR) plant have been conducted at Japan Atomic Energy Research Institute. The conceptual design has been completed and the more detailed design works and the safety analysis of the experimental VHTR plant are continued. The purposes of design studies are to show the feasibility of the experimental VHTR program, to specify the characteristics and functions of the plant components, to point out the R and D items necessary for the experimental VHTR plant construction, and to analyze the feature of the plant safety. In this paper the summary of system design and safety features of the experimental reactor are indicated. Main issues are the safety philosophy for the design basis accident, the accidents assumed and the engineered safety systems adopted in the design works

Two polynomial representations of experimental design

OpenAIRE

Notari, Roberto; Riccomagno, Eva; Rogantin, Maria-Piera

2007-01-01

In the context of algebraic statistics an experimental design is described by a set of polynomials called the design ideal. This, in turn, is generated by finite sets of polynomials. Two types of generating sets are mostly used in the literature: Groebner bases and indicator functions. We briefly describe them both, how they are used in the analysis and planning of a design and how to switch between them. Examples include fractions of full factorial designs and designs for mixture experiments.

A Combined Experimental and Computational Approach to Subject-Specific Analysis of Knee Joint Laxity

Science.gov (United States)

Harris, Michael D.; Cyr, Adam J.; Ali, Azhar A.; Fitzpatrick, Clare K.; Rullkoetter, Paul J.; Maletsky, Lorin P.; Shelburne, Kevin B.

2016-01-01

Modeling complex knee biomechanics is a continual challenge, which has resulted in many models of varying levels of quality, complexity, and validation. Beyond modeling healthy knees, accurately mimicking pathologic knee mechanics, such as after cruciate rupture or meniscectomy, is difficult. Experimental tests of knee laxity can provide important information about ligament engagement and overall contributions to knee stability for development of subject-specific models to accurately simulate knee motion and loading. Our objective was to provide combined experimental tests and finite-element (FE) models of natural knee laxity that are subject-specific, have one-to-one experiment to model calibration, simulate ligament engagement in agreement with literature, and are adaptable for a variety of biomechanical investigations (e.g., cartilage contact, ligament strain, in vivo kinematics). Calibration involved perturbing ligament stiffness, initial ligament strain, and attachment location until model-predicted kinematics and ligament engagement matched experimental reports. Errors between model-predicted and experimental kinematics averaged ligaments agreed with literature descriptions. These results demonstrate the ability of our constraint models to be customized for multiple individuals and simultaneously call attention to the need to verify that ligament engagement is in good general agreement with literature. To facilitate further investigations of subject-specific or population based knee joint biomechanics, data collected during the experimental and modeling phases of this study are available for download by the research community. PMID:27306137

Program computes single-point failures in critical system designs

Science.gov (United States)

Brown, W. R.

1967-01-01

Computer program analyzes the designs of critical systems that will either prove the design is free of single-point failures or detect each member of the population of single-point failures inherent in a system design. This program should find application in the checkout of redundant circuits and digital systems.

Experimental Setups for Single Event Effect Studies

OpenAIRE

N. H. Medina; V. A. P. Aguiar; N. Added; F. Aguirre; E. L. A. Macchione; S. G. Alberton; M. A. G. Silveira; J. Benfica; F. Vargas; B. Porcher

2016-01-01

Experimental setups are being prepared to test and to qualify electronic devices regarding their tolerance to Single Event Effect (SEE). A multiple test setup and a new beam line developed especially for SEE studies at the São Paulo 8 UD Pelletron accelerator were prepared. This accelerator produces proton beams and heavy ion beams up to 107Ag. A Super conducting Linear accelerator, which is under construction, may fulfill all of the European Space Agency requirements to qualify electronic...

Experimental toxicology: Issues of statistics, experimental design, and replication.

Science.gov (United States)

Briner, Wayne; Kirwan, Jeral

2017-01-01

The difficulty of replicating experiments has drawn considerable attention. Issues with replication occur for a variety of reasons ranging from experimental design to laboratory errors to inappropriate statistical analysis. Here we review a variety of guidelines for statistical analysis, design, and execution of experiments in toxicology. In general, replication can be improved by using hypothesis driven experiments with adequate sample sizes, randomization, and blind data collection techniques. Copyright © 2016 Elsevier B.V. All rights reserved.

Human subjects and experimental irradiation

International Nuclear Information System (INIS)

Rosen, R.

1985-01-01

In recent years the public has expressed concern about the use of human subjects in scientific research. Some professional institutions have adopted codes of practice to guide them in this matter. At the University of New South Wales, where human subjects are used in teaching and research programmes, a committee ensures that high ethical standards are maintained. As the volunteer subjects do not gain any benefit themselves from the procedures, their level of risk is kept low. One type of procedure in which risk is becoming quantifiable, is the irradiation of human subjects. To assist peer review groups, the ICRP, WHO and the National Health and Medical Research Council have enunciated principles which should be followed in the irradiation of human volunteer subjects. In general the role of the Committee is advisory to protect the rights of the investigator, the subject, and the institution. Some of the inherent problems are discussed

Experimental research on single phase convection heat transfer in micro-fin tube

International Nuclear Information System (INIS)

Fan Guangming; Sun Zhongning; Zhu Sheng

2011-01-01

An experimental investigation of heat transfer and flow resistance characteristics of single phase water in three micro-fin tubes with different fin height was conducted. At the same time, the efficiency of micro-fin tubes within the experimental scope was evaluated and the optimal working region was determined. Based on the experimental data in the optimal working region, correlations for predicting the heat transfer and flow resistance were also given by multiple regression method. The result indicates that the micro-fin tubes can greatly enhance the single-phase heat transfer in turbulent flow, and the increase of heat transfer coefficient is higher than the increase of flow resistance. The accuracy of the correlation is very high, of which the deviation from the experimental value is very small. (authors)

A new microcavity design for single molecule detection

International Nuclear Information System (INIS)

Steiner, M.; Schleifenbaum, F.; Stupperich, C.; Failla, A.V.; Hartschuh, A.; Meixner, A.J.

2006-01-01

We present a new microcavity design which allows for efficient detection of single molecules by measuring the molecular fluorescence emission coupled into a resonant cavity mode. The Fabry-Perot-type microresonator consists of two silver mirrors separated by a thin polymer film doped with dye molecules in ultralow concenctration. By slightly tilting one of the mirrors different cavity lengths can be selected within the same sample. Locally, on a μm scale, the microcavity still acts as a planar Fabry-Perot resonator. Using scanning confocal fluorescence microscopy, single emitters on resonance with a single mode of the microresonator can be spatially addressed. Our microcavity is demonstrated to be well-suited for investigating the coupling mechanism between single quantum emitters and single modes of the electromagnetic field. The microcavity layout could be integrated in a lab-on-a-microchip design for ultrasensitive microfluidic analytics and can be considered as an important improvement for single photon sources based on single molecules operating at room temperature

Single liner shipping service design

DEFF Research Database (Denmark)

Plum, Christian Edinger Munk; Pisinger, David; Salazar-González, Juan-José

2014-01-01

The design of container shipping networks is an important logistics problem, involving assets and operational costs measured in billions of dollars. To guide the optimal deployment of the ships, a single vessel round trip is considered by minimizing operational costs and flowing the best paying...

Moving characteristics of single file passengers considering the effect of ship trim and heeling

Science.gov (United States)

Sun, Jinlu; Lu, Shouxiang; Lo, Siuming; Ma, Jian; Xie, Qimiao

2018-01-01

Ship listing and motion affects the movement pattern of passengers on board, thus pedestrian traffic and evacuation dynamics would be significantly different from those on level ground. To quantify the influence of ship listing and motion on passenger evacuation, we designed a ship corridor simulator, with which we performed single-file pedestrian movement experiments considering the effect of trim and heeling. Results indicated that density is not the only factor that affects pedestrian speed under ship trim or heeling conditions, for that both individual walking speed and group walking speed would be greatly attenuated due to the influence of the trim angles. However, heeling angles show less impact on speed when compared with trim angles. In addition, the speed correlation coefficient between the adjacent experimental subjects would be higher with larger angles and lower speed. Moreover, both female and male experimental subjects need similar distance headway for walking in different trim or heeling conditions. Furthermore, experimental subjects with lower individual walking speed need longer time headway to keep enough distance headway. This work will provide fundamental guidance to the development of evacuation models and the design of evacuation facilities on board.

Comparison of forward versus backward walking using body weight supported treadmill training in an individual with a spinal cord injury: a single subject design.

Science.gov (United States)

Moriello, Gabriele; Pathare, Neeti; Cirone, Cono; Pastore, Danielle; Shears, Dacia; Sulehri, Sahira

2014-01-01

Body weight supported treadmill training (BWSTT) is a task-specific intervention that promotes functional locomotion. There is no research evaluating the effect of backward walking (BW) using BWSTT in individuals with spinal cord injury (SCI). The purpose of this single subject design was to examine the differences between forward walking (FW) and BW training using BWSTT in an individual with quadriparesis. The participant was a 57-year-old male with incomplete C3-C6 SCI. An ABABAB design (A = BW; B = FW; each phase = 3 weeks of biweekly sessions) was utilized. Outcome measures included: gait parameters; a timed 4-meter walk; the 5-repetition sit-to-stand test (STST); tandem stance time; and 6-minute walk test (6MWT). Data was analyzed with split level method of trend estimation. Improvements in gait parameters, on the timed 4-meter walk, 6MWT, tandem balance and aerobic endurance were similar with FW and BW training. The only difference between FW and BW training was that BW training resulted in greater improvements in the STST. The results of this study suggest that in this individual backward walking training was advantageous, resulting in improved ability to perform the 5-repetition STST. It is suspected that these changes can be attributed to the differences in muscle activation and task difficulty between FW and BW.

Pen needle design influences ease of insertion, pain, and skin trauma in subjects with type 2 diabetes.

Science.gov (United States)

Præstmark, Kezia A; Jensen, Morten L; Madsen, Nils B; Kildegaard, Jonas; Stallknecht, Bente M

2016-01-01

Pen needles used for subcutaneous injections have gradually become shorter, thinner and more thin walled, and thereby less robust to patient reuse. Thus, different needle sizes, alternative tip designs and needles resembling reuse were tested to explore how needle design influences ease of insertion, pain and skin trauma. 30 subjects with injection-treated type 2 diabetes and body mass index 25-35 kg/m 2 were included in the single-blinded study. Each subject received abdominal insertions with 18 different types of needles. All needles were tested twice per subject and in random order. Penetration force (PF) through the skin, pain perception on 100 mm visual analog scale, and change in skin blood perfusion (SBP) were quantified after the insertions. Needle diameter was positively related to PF and SBP (ptrend relation. Lack of needle lubrication and small 'needle hooks' increased PF and SBP (pskin and in polyurethane rubber were linearly related, and pain outcome was dependent of SBP increase. The shape and design of a needle and the needle tip affect ease of insertion, pain and skin trauma. Relations are seen across different data acquisition methods and across species, enabling needle performance testing outside of clinical trials. NCT02531776; results.

Single- and Multiple-Dose Study To Determine the Safety, Tolerability, Pharmacokinetics, and Food Effect of Oral MRX-I versus Linezolid in Healthy Adult Subjects.

Science.gov (United States)

Eckburg, Paul B; Ge, Yigong; Hafkin, Barry

2017-04-01

A multipart phase 1 study was conducted to determine the safety, tolerability, pharmacokinetics, and food effect of the novel oral oxazolidinone, MRX-I, in healthy adults, as well as the tolerability of longer-term exposure of both oral MRX-I and linezolid. Thirty subjects in part 1 received single ascending doses of MRX-I or placebo under fasting or fed condition in a double-blind crossover design. Twelve subjects in part 2 received MRX-I at 800 mg every 12 h (q12h) for 14 days in a double-blind, placebo-controlled design. In part 3, 24 subjects were randomized to receive 28 days of MRX-I at 800 mg q12h or oral linezolid at 600 mg q12h for 28 days in a double-blind, double-dummy design. Oral MRX-I was associated with a greater bioavailability and exposure when administered with food, and minimal accumulation of MRX-I occurred after multiple-dose administration. Oral MRX-I was well tolerated at single doses of up to 1,200 and 800 mg q12h for up to 28 days; all adverse events were mild to moderate in severity, and there was no drug discontinuation due to adverse events. These data support further clinical development of oral MRX-I in the treatment of resistant Gram-positive bacterial infections. Copyright © 2017 American Society for Microbiology.

Design of Circular, Square, Single, and Multi-layer Induction Coils for Electromagnetic Priming Using Inductance Estimates

Science.gov (United States)

Fritzsch, Robert; Kennedy, Mark W.; Aune, Ragnhild E.

2018-02-01

Special induction coils used for electro magnetic priming of ceramic foam filters in liquid metal filtration have been designed using a combination of analytical and finite element modeling. Relatively simple empirical equations published by Wheeler in 1928 and 1982 have been used during the design process. The equations were found to accurately predict the z-component of the magnetic flux densities of both single- and multi-layer coils as verified both experimentally and by using COMSOL® 5.1 multiphysics simulations.

An Improved Rank Correlation Effect Size Statistic for Single-Case Designs: Baseline Corrected Tau.

Science.gov (United States)

Tarlow, Kevin R

2017-07-01

Measuring treatment effects when an individual's pretreatment performance is improving poses a challenge for single-case experimental designs. It may be difficult to determine whether improvement is due to the treatment or due to the preexisting baseline trend. Tau- U is a popular single-case effect size statistic that purports to control for baseline trend. However, despite its strengths, Tau- U has substantial limitations: Its values are inflated and not bound between -1 and +1, it cannot be visually graphed, and its relatively weak method of trend control leads to unacceptable levels of Type I error wherein ineffective treatments appear effective. An improved effect size statistic based on rank correlation and robust regression, Baseline Corrected Tau, is proposed and field-tested with both published and simulated single-case time series. A web-based calculator for Baseline Corrected Tau is also introduced for use by single-case investigators.

Theoretical and experimental study of single particle tracking in extreme conditions: single photon imaging

International Nuclear Information System (INIS)

Cajgfinger, T.

2012-10-01

This manuscript presents my thesis on the high frame rate (500 frames / second) single-photon detector electron-bombarded CMOS (ebCMOS). The first section compares three ultra-sensitive detectors and their methods for improving photon sensitivity: the CMOS low noise (sCMOS), the electron-multiplying CCD (emCCD) with signal multiplication by pixel and the ebCMOS with amplification by applied electric field. The method developed to detect single photon impacts with intra-pixel resolution on the ebCMOS sensor is presented. The second section compares the localization accuracy of these detectors in extreme conditions of very low photon flux (<10 photons/frame). First the theoretical limit is calculated using the Cramer-Rao lower bound for significant parameter sets. An experimental comparison of the detectors is then described. The setup provides one or more point sources controlled in position, signal and background noise. The results allow a comparison of the experimental effectiveness, purity and localization accuracy. The last section describes two experiments with the ebCMOS camera. The first aims at tracking hundreds of quantum dots simultaneously at the Nanoptec center. The second focuses on the swimming of bacteria at the surface at the Joliot Curie Institute. The point sources tracking algorithm using single photons and the Kalman filter implementation developed for these experiments is also described. (author)

The role of chemometrics in single and sequential extraction assays: a review. Part II. Cluster analysis, multiple linear regression, mixture resolution, experimental design and other techniques.

Science.gov (United States)

Giacomino, Agnese; Abollino, Ornella; Malandrino, Mery; Mentasti, Edoardo

2011-03-04

Single and sequential extraction procedures are used for studying element mobility and availability in solid matrices, like soils, sediments, sludge, and airborne particulate matter. In the first part of this review we reported an overview on these procedures and described the applications of chemometric uni- and bivariate techniques and of multivariate pattern recognition techniques based on variable reduction to the experimental results obtained. The second part of the review deals with the use of chemometrics not only for the visualization and interpretation of data, but also for the investigation of the effects of experimental conditions on the response, the optimization of their values and the calculation of element fractionation. We will describe the principles of the multivariate chemometric techniques considered, the aims for which they were applied and the key findings obtained. The following topics will be critically addressed: pattern recognition by cluster analysis (CA), linear discriminant analysis (LDA) and other less common techniques; modelling by multiple linear regression (MLR); investigation of spatial distribution of variables by geostatistics; calculation of fractionation patterns by a mixture resolution method (Chemometric Identification of Substrates and Element Distributions, CISED); optimization and characterization of extraction procedures by experimental design; other multivariate techniques less commonly applied. Copyright © 2010 Elsevier B.V. All rights reserved.

Effects of Oral Stimulation Intervention in Newborn Babies with Cri du Chat Syndrome: Single-Subject Research Design

Directory of Open Access Journals (Sweden)

Mi Kyung Kim

2018-01-01

Full Text Available The purpose of this study is to treat dysphagia in a newborn baby with cri du chat syndrome using an oral stimulation intervention and to examine its effects. The subject of this study was a baby born 2 weeks prematurely. Since birth, his oxygen saturation (SaO2 decreased while feeding, and he had difficulty with mouth feeding. Thus, an NG feeding tube was inserted, and dysphagia treatment was initiated on the sixth day after birth. A baseline phase and an intervention phase were performed using an AB design. The oral stimulation intervention was not performed in the baseline phase, as only nonnutritive sucking training using a rubber pacifier was used during the baseline phase. During the intervention phase, nonnutritive sucking training and oral stimulation intervention were simultaneously conducted. After the intervention period, daily oral milk intake and intake per feeding of the subject noticeably increased. The oxygen saturation while feeding rose over 90% on average, and the baby did not present with hypoxia. The oral stimulation intervention provided prior to feeding resulted in highly positive effects, including induced normal development of the baby, stimulation of his transition from the NG feeding tube to bottle feeding, increased oxygen saturation, and a shortened hospital stay.

Design and experimental study of a multi-modal piezoelectric energy harvester

Energy Technology Data Exchange (ETDEWEB)

Xiong, Xing Yu [School of Energy, Power and Mechanical Engineering, North China Electric Power University, Beijing (China); Oyadiji, S. Olutunde [School of Mechanical, Aerospace and Civil Engineering, The University of Manchester, Manchester (United States)

2017-01-15

A multi-modal piezoelectric vibration energy harvester is designed in this article. It consists of a cantilevered base beam and some upper and lower layer beams with rigid masses bonded between the beams as spacers. For a four-layer harvester subjected to random base excitations, relocating the mass positions leads to the generation of up to four close resonance frequencies over the frequency range from 10 Hz to 100 Hz with relative large power output. The harvesters are connected with a resistance decade box and the frequency response functions of the voltage and power on resistive loads are determined. The experimental results are validated with the simulation results using the finite element method. On a certain level of power output, the experimental results show that the multi-modal harvesters can generate a frequency band that is more than two times greater than the frequency band produced by a cantilevered beam harvester.

An experimental design method leading to chemical Turing patterns.

Science.gov (United States)

Horváth, Judit; Szalai, István; De Kepper, Patrick

2009-05-08

Chemical reaction-diffusion patterns often serve as prototypes for pattern formation in living systems, but only two isothermal single-phase reaction systems have produced sustained stationary reaction-diffusion patterns so far. We designed an experimental method to search for additional systems on the basis of three steps: (i) generate spatial bistability by operating autoactivated reactions in open spatial reactors; (ii) use an independent negative-feedback species to produce spatiotemporal oscillations; and (iii) induce a space-scale separation of the activatory and inhibitory processes with a low-mobility complexing agent. We successfully applied this method to a hydrogen-ion autoactivated reaction, the thiourea-iodate-sulfite (TuIS) reaction, and noticeably produced stationary hexagonal arrays of spots and parallel stripes of pH patterns attributed to a Turing bifurcation. This method could be extended to biochemical reactions.

Bayesian optimal experimental design for the Shock-tube experiment

International Nuclear Information System (INIS)

Terejanu, G; Bryant, C M; Miki, K

2013-01-01

The sequential optimal experimental design formulated as an information-theoretic sensitivity analysis is applied to the ignition delay problem using real experimental. The optimal design is obtained by maximizing the statistical dependence between the model parameters and observables, which is quantified in this study using mutual information. This is naturally posed in the Bayesian framework. The study shows that by monitoring the information gain after each measurement update, one can design a stopping criteria for the experimental process which gives a minimal set of experiments to efficiently learn the Arrhenius parameters.

On the construction of experimental designs for a given task by jointly optimizing several quality criteria: Pareto-optimal experimental designs.

Science.gov (United States)

Sánchez, M S; Sarabia, L A; Ortiz, M C

2012-11-19

Experimental designs for a given task should be selected on the base of the problem being solved and of some criteria that measure their quality. There are several such criteria because there are several aspects to be taken into account when making a choice. The most used criteria are probably the so-called alphabetical optimality criteria (for example, the A-, E-, and D-criteria related to the joint estimation of the coefficients, or the I- and G-criteria related to the prediction variance). Selecting a proper design to solve a problem implies finding a balance among these several criteria that measure the performance of the design in different aspects. Technically this is a problem of multi-criteria optimization, which can be tackled from different views. The approach presented here addresses the problem in its real vector nature, so that ad hoc experimental designs are generated with an algorithm based on evolutionary algorithms to find the Pareto-optimal front. There is not theoretical limit to the number of criteria that can be studied and, contrary to other approaches, no just one experimental design is computed but a set of experimental designs all of them with the property of being Pareto-optimal in the criteria needed by the user. Besides, the use of an evolutionary algorithm makes it possible to search in both continuous and discrete domains and avoid the need of having a set of candidate points, usual in exchange algorithms. Copyright © 2012 Elsevier B.V. All rights reserved.

Experimental study on the performance of single screw expanders by gap adjustment

International Nuclear Information System (INIS)

Wang, Wei; Wu, Yu-ting; Ma, Chong-fang; Xia, Guo-dong; Wang, Jing-fu

2013-01-01

Improving thermodynamic efficiency of prime movers is the key issue for efficient utilization of low-temperature heat resources. Single screw expander may be a good candidate because of its many good characteristics. Precisions in manufacture and assembly are very important factors to the performance of single screw expanders. In this paper, the shaft efficiency, volumetric efficiency and gas consumption rate of the single screw expander prototypes were tested and discussed. We have manufactured three prototypes with different gaps to investigate their performance. The first prototype (A) has the largest gap, and the second one (B) has the smallest gap, the third prototype (C) has the medium gap configuration. Experimental result of the prototypes was obtained. From the experimental data of prototype A, the power output was about 5 kW, the gas consumption rate was above 105 kg/kWh and the volumetric efficiency was below 20%, the shaft efficiency was only 34%. From experimental data of prototype B, the mass flow rate was significantly decreased. The power output was only 1.4 kW and the volumetric efficiency was slightly lower than prototype A. The gas consumption rate was much more than that of prototype A. From the experimental data of prototype C, the power output was about 4.5 kW, but the mass flow rate was sharply decreased. The gas consumption rate was about 65 kg/kWh, the maximum volumetric efficiency was about 66%, and the shaft efficiency was about 60%. The experimental results indicated that prototype C of single screw expanders had the best overall performance, which may be further improved by optimizing its configuration. - Highlights: • The experiment for three single screw expander prototypes at different gaps was carried out. • Maximum shaft efficiency is about 60%. • Minimum gas consumption rate is about 65 kg/kWh. • Maximum volumetric efficiency is about 66%. • Leaked gas still has part of working capability

Strain measurement of objects subjected to aerodynamic heating using digital image correlation: experimental design and preliminary results.

Science.gov (United States)

Pan, Bing; Jiang, Tianyun; Wu, Dafang

2014-11-01

In thermomechanical testing of hypersonic materials and structures, direct observation and quantitative strain measurement of the front surface of a test specimen directly exposed to severe aerodynamic heating has been considered as a very challenging task. In this work, a novel quartz infrared heating device with an observation window is designed to reproduce the transient thermal environment experienced by hypersonic vehicles. The specially designed experimental system allows the capture of test article's surface images at various temperatures using an optical system outfitted with a bandpass filter. The captured images are post-processed by digital image correlation to extract full-field thermal deformation. To verify the viability and accuracy of the established system, thermal strains of a chromiumnickel austenite stainless steel sample heated from room temperature up to 600 °C were determined. The preliminary results indicate that the air disturbance between the camera and the specimen due to heat haze induces apparent distortions in the recorded images and large errors in the measured strains, but the average values of the measured strains are accurate enough. Limitations and further improvements of the proposed technique are discussed.

Single-subject structural networks with closed-form rotation invariant matching mprove power in developmental studies of the cortex.

Science.gov (United States)

Kandel, Benjamin M; Wang, Danny J J; Gee, James C; Avants, Brian B

2014-01-01

Although much attention has recently been focused on single-subject functional networks, using methods such as resting-state functional MRI, methods for constructing single-subject structural networks are in their infancy. Single-subject cortical networks aim to describe the self-similarity across the cortical structure, possibly signifying convergent developmental pathways. Previous methods for constructing single-subject cortical networks have used patch-based correlations and distance metrics based on curvature and thickness. We present here a method for constructing similarity-based cortical structural networks that utilizes a rotation-invariant representation of structure. The resulting graph metrics are closely linked to age and indicate an increasing degree of closeness throughout development in nearly all brain regions, perhaps corresponding to a more regular structure as the brain matures. The derived graph metrics demonstrate a four-fold increase in power for detecting age as compared to cortical thickness. This proof of concept study indicates that the proposed metric may be useful in identifying biologically relevant cortical patterns.

EXPERIMENTAL RESEARCH REGARDING LEATHER APPLICATIONS IN PRODUCT DESIGN

Directory of Open Access Journals (Sweden)

PRALEA Jeni

2015-05-01

Full Text Available This paper presents the role and importance of experimental research in design activity. The designer, as a researcher and a project manager, proposes to establish a relationship between functional-aesthetic-constructive-technological-economic,based on the aesthetic possibilities of the materials used for the experiments. With the aim to identify areas for the application of leather waste resulted from the production process, the paper presents experiments conducted with this material in combination with wood, by using different techniques that lead to different aesthetic effects. Identifying the areas to use and creating products from leather and/or wood waste, is based on the properties of these materials. Leather, the subject of these experiments, has the advantage that it can be used on both sides. Tactile differences of the two sides of this material has both aesthetical and functional advantages, which makes it suitable for applications on products that meet the requirements of "design for all". With differentiated tactile characteristics, in combination with other materials, for these experiments wood, easily "read touch" products can be generated to help people with certain disabilities. Thus, experiments presented in this paper allows the establishment of aesthetic schemes applicable to products that are friendly both with the environment (based on the reuse of wood and leather waste and with the users (can be used as applications, accessories and concepts of products for people with certain disabilities. The designer’s choices or decisions can be based on the results of this experiment. The experiment enables the designer to develop creative, innovative and environmentally friendly products.

Safety and feasibility of transcranial direct current stimulation in amyotrophic lateral sclerosis - a pilot study with a single subject experimental design.

Science.gov (United States)

Madhavan, Sangeetha; Sivaramakrishnan, Anjali; Bond, Sam; Jiang, Qin Li

2018-02-28

Transcranial direct current stimulation (tDCS) has been explored as a neuromodulatory tool to prime motor function in several neurological disorders. Studies using tDCS in amyotrophic lateral sclerosis (ALS) are limited. We investigated the safety, feasibility and effects of long-term tDCS in an individual with ALS. A 36-year-old male diagnosed with clinically definite ALS received 12 sessions each of anodal, sham, and cathodal tDCS. Outcome measures included disease progression (revised ALS functional rating scale (ALSFRS-R)), clinical measures of endurance and mobility, and corticomotor excitability. No adverse events or change in disease progression were noticed during the study. Small improvement in gait speed (15% increase) was noticed with anodal tDCS only. This case study demonstrates the safety and feasibility of long-term facilitatory and inhibitory tDCS on a single participant with ALS. This study serves as a guideline for implementing tDCS in future ALS trials.

Multi-disciplinary design optimization and performance evaluation of a single stage transonic axial compressor

International Nuclear Information System (INIS)

Lee, Sae Il; Lee, Dong Ho; Kim, Kyu Hong; Park, Tae Choon; Lim, Byeung Jun; Kang, Young Seok

2013-01-01

The multidisciplinary design optimization method, which integrates aerodynamic performance and structural stability, was utilized in the development of a single-stage transonic axial compressor. An approximation model was created using artificial neural network for global optimization within given ranges of variables and several design constraints. The genetic algorithm was used for the exploration of the Pareto front to find the maximum objective function value. The final design was chosen after a second stage gradient-based optimization process to improve the accuracy of the optimization. To validate the design procedure, numerical simulations and compressor tests were carried out to evaluate the aerodynamic performance and safety factor of the optimized compressor. Comparison between numerical optimal results and experimental data are well matched. The optimum shape of the compressor blade is obtained and compared to the baseline design. The proposed optimization framework improves the aerodynamic efficiency and the safety factor.

Research Methods in Healthcare Epidemiology and Antimicrobial Stewardship-Quasi-Experimental Designs.

Science.gov (United States)

Schweizer, Marin L; Braun, Barbara I; Milstone, Aaron M

2016-10-01

Quasi-experimental studies evaluate the association between an intervention and an outcome using experiments in which the intervention is not randomly assigned. Quasi-experimental studies are often used to evaluate rapid responses to outbreaks or other patient safety problems requiring prompt, nonrandomized interventions. Quasi-experimental studies can be categorized into 3 major types: interrupted time-series designs, designs with control groups, and designs without control groups. This methods paper highlights key considerations for quasi-experimental studies in healthcare epidemiology and antimicrobial stewardship, including study design and analytic approaches to avoid selection bias and other common pitfalls of quasi-experimental studies. Infect Control Hosp Epidemiol 2016;1-6.

Design for subjective well-being in interior architecture

NARCIS (Netherlands)

Petermans, A.; Pohlmeyer, A.E.

2014-01-01

Can interior environments engage people in pleasurable and meaningful experiences and thereby have a positive influence on their happiness? This paper discusses why and how interior architects might want to consider implementing ideas in relation to ‘design for subjective well-being’. Despite of

A new design approach for control circuits of pipelined single-flux-quantum microprocessors

International Nuclear Information System (INIS)

Yamanashi, Y; Akimoto, A; Yoshikawa, N; Tanaka, M; Kawamoto, T; Kamiya, Y; Fujimaki, A; Terai, H; Yorozu, S

2006-01-01

A novel method of design for controllers of pipelined microprocessors using single-flux-quantum (SFQ) logic has been proposed. The proposed design approach is based on one hot encoding and is very suitable for designing a finite state machine using SFQ logic circuits, where each internal state of the microprocessor is represented by a flip-flop. In this approach, decoding of the internal state can be performed instantaneously, in contrast to the case in the conventional method using a binary state register. Moreover, pipelining is effectively implemented without increasing the circuit size because no pipeline registers are required in the one hot encoding. By using this method, we have designed a controller for our new SFQ microprocessors, which employs pipelining. The number of Josephson junctions of the newly designed controller is 1067, while the previous version without pipelining contains 1721 Josephson junctions. These results indicate that the proposed design approach is very effective for pipelined SFQ microprocessors. We have implemented a new controller using the NEC 2.5 kA cm -2 Nb standard process and confirmed its correct operation experimentally

Design parameters for voltage-controllable directed assembly of single nanoparticles

International Nuclear Information System (INIS)

Porter, Benjamin F; Bhaskaran, Harish; Abelmann, Leon

2013-01-01

Techniques to reliably pick-and-place single nanoparticles into functional assemblies are required to incorporate exotic nanoparticles into standard electronic circuits. In this paper we explore the use of electric fields to drive and direct the assembly process, which has the advantage of being able to control the nano-assembly process at the single nanoparticle level. To achieve this, we design an electrostatic gating system, thus enabling a voltage-controllable nanoparticle picking technique. Simulating this system with the nonlinear Poisson–Boltzmann equation, we can successfully characterize the parameters required for single particle placement, the key being single particle selectivity, in effect designing a system that can achieve this controllably. We then present the optimum design parameters required for successful single nanoparticle placement at ambient temperature, an important requirement for nanomanufacturing processes. (paper)

Analysis of an adhesively bonded single lap joint subjected to eccentric loading

DEFF Research Database (Denmark)

Anyfantis, Konstantinos; Tsouvalis, N. G.

2013-01-01

is benchmarking of computational tools. The test is based on a Single Lap Joint subjected to Eccentric Loading (SLJ-EL). The basic concept that lies behind this configuration is that the applied in-plane tensile load leads the adhesive layer to develop normal stresses, in-plane and out-of-plane shear stresses...

Revised design for the Tokamak experimental power reactor

International Nuclear Information System (INIS)

Stacey, W.M. Jr.; Abdou, M.A.; Brooks, J.N.

1977-03-01

A new, preliminary design has been identified for the tokamak experimental power reactor (EPR). The revised EPR design is simpler, more compact, less expensive and has somewhat better performance characteristics than the previous design, yet retains many of the previously developed design concepts. This report summarizes the principle features of the new EPR design, including performance and cost

Experimental design matters for statistical analysis

DEFF Research Database (Denmark)

Jensen, Signe Marie; Schaarschmidt, Frank; Onofri, Andrea

2018-01-01

, the experimental design is often more or less neglected when analyzing data. Two data examples were analyzed using different modelling strategies: Firstly, in a randomized complete block design, mean heights of maize treated with a herbicide and one of several adjuvants were compared. Secondly, translocation...... of an insecticide applied to maize as a seed treatment was evaluated using incomplete data from an unbalanced design with several layers of hierarchical sampling. Extensive simulations were carried out to further substantiate the effects of different modelling strategies. RESULTS: It was shown that results from sub...

Development of the Biological Experimental Design Concept Inventory (BEDCI)

Science.gov (United States)

Deane, Thomas; Nomme, Kathy; Jeffery, Erica; Pollock, Carol; Birol, Gulnur

2014-01-01

Interest in student conception of experimentation inspired the development of a fully validated 14-question inventory on experimental design in biology (BEDCI) by following established best practices in concept inventory (CI) design. This CI can be used to diagnose specific examples of non-expert-like thinking in students and to evaluate the…

Experimental design for parameter estimation of two time-scale model of photosynthesis and photoinhibition in microalgae

Czech Academy of Sciences Publication Activity Database

Papáček, Š.; Čelikovský, Sergej; Rehák, Branislav; Štys, D.

2010-01-01

Roč. 80, č. 6 (2010), s. 1302-1309 ISSN 0378-4754 R&D Projects: GA ČR(CZ) GA102/08/0186 Institutional research plan: CEZ:AV0Z10750506 Keywords : Photosynthetic factory * Experimental design * Parameter estimation * Two-scale modeling Subject RIV: BC - Control Systems Theory Impact factor: 0.812, year: 2010 http://library.utia.cas.cz/separaty/2010/TR/celikovsky-0341543.pdf

EFFECTIVENESS OF ROCABADO'S TECHNIQUE FOR SUBJECTS WITH TEMPOROMANDIBULAR JOINT DYSFUNCTION - A SINGLE BLIND STUDY

Directory of Open Access Journals (Sweden)

Niha Siraj Mulla

2015-02-01

Full Text Available Background:A temporo-mandibular joint dysfunction or TMD is a group of conditions characterized by pain in the muscles of mastication, the temporo-mandiblar joint or both. Rocabado has described techniques includes the Rocabado’s manipulation and Rocabado’s exercises which have both been individually advocated for treatment of TMD. The purpose of study is to determine the effectiveness of Rocabado’s techniques on TMJ dysfunction symptoms, pain, TMJ Range of Motion (ROM and jaw functional limitation for subjects with temporo-mandibular joint dysfunction. Method: Pre to post test experimental study design, subjects with temporo-mandibular joint dysfunction randomized into two groups with 15 subjects into each group with total of 30 subjects in Study and control group, respectively. The study group received the Rocabado’s technique which consisted of Rocabado’s non-thrust TMJ manipulation and Rocabado’s exercises along with conventional TMJ exercises and the control group received only conventional TMJ exercises. The exercises were performed for 6 times per each session, six times in a day, one session under supervision and remaining five sessions by the subject at home for 6 days in a week for duration of 2 weeks. The outcome measurements such as VAS for pain, TMJ ROM, Fonseca’s questionnaire rating for TMJ dysfunction symptoms and jaw function limitation score (JFLS was measured before and after two weeks of intervention. Results: Comparative analysis, using Independent ‘t’ test and Mann Whitney U- test found that the means of VAS, TMJ ROM, Fonseca’s questionnaire and JFLS scores showed statistically significant difference (p <0.05 when the pre-intervention means and post-intervention means were compared between two groups. Conclusion: It is concluded that Rocabado’s technique found to have statistically and clinically significant added effect with conventional TMJ exercises shown greater percentage of improvements obtained

Design and analysis of linear oscillatory single-phase permanent magnet generator for free-piston stirling engine systems

Science.gov (United States)

Kim, Jeong-Man; Choi, Jang-Young; Lee, Kyu-Seok; Lee, Sung-Ho

2017-05-01

This study focuses on the design and analysis of a linear oscillatory single-phase permanent magnet generator for free-piston stirling engine (FPSE) systems. In order to implement the design of linear oscillatory generator (LOG) for suitable FPSEs, we conducted electromagnetic analysis of LOGs with varying design parameters. Then, detent force analysis was conducted using assisted PM. Using the assisted PM gave us the advantage of using mechanical strength by detent force. To improve the efficiency, we conducted characteristic analysis of eddy-current loss with respect to the PM segment. Finally, the experimental result was analyzed to confirm the prediction of the FEA.

Slow drilling speeds for single-drill implant bed preparation. Experimental in vitro study.

Science.gov (United States)

Delgado-Ruiz, R A; Velasco Ortega, E; Romanos, G E; Gerhke, S; Newen, I; Calvo-Guirado, J L

2018-01-01

To evaluate the real-time bone temperature changes during the preparation of the implant bed with a single-drill protocol with different drill designs and different slow drilling speeds in artificial type IV bone. For this experimental in vitro study, 600 implant bed preparations were performed in 10 bovine bone disks using three test slow drilling speeds (50/150/300 rpm) and a control drilling speed (1200 rpm). The temperature at crestal and apical areas and time variations produced during drilling with three different drill designs with similar diameter and length but different geometry were recorded with real-life thermographic analysis. Statistical analysis was performed by two-way analysis of variance. Multiple comparisons of temperatures and time with the different drill designs and speeds were performed with the Tukey's test. T Max values for the control drilling speed with all the drill designs (D1 + 1200; D2 + 1200; D3 + 1200) were higher compared to those for the controls for 11 ± 1.32 °C (p drilling at 50 rpm resulted in the lowest temperature increment (22.11 ± 0.8 °C) compared to the other slow drilling speeds of 150 (24.752 ± 1.1 °C) and 300 rpm (25.977 ± 1.2 °C) (p drilling speeds compared to that for the control drilling speed. Slow drilling speeds required significantly more time to finish the preparation of the implant bed shown as follows: 50 rpm > 150 rpm > 300 rpm > control (p drill protocol with slow drilling speeds (50, 150, and 300 rpm) without irrigation in type IV bone increases the temperature at the coronal and apical levels but is below the critical threshold of 47 °C. The drill design in single-drill protocols using slow speeds (50, 150, and 300 rpm) does not have an influence on the thermal variations. The time to accomplish the implant bed preparation with a single-drill protocol in type IV bone is influenced by the drilling speed and not by the drill design. As the speed decreases, then

Performance evaluation of a piezoactuator-based single-stage valve system subjected to high temperature

Science.gov (United States)

Jeon, Juncheol; Han, Chulhee; Chung, Jye Ung; Choi, Seung-Bok

2015-01-01

In this paper, a novel single-stage valve system activated by a piezostack actuator is proposed and experimentally evaluated at both room temperature (20 °C) and high temperature (100 °C) conditions. A hinge-lever displacement amplifier is adopted in the valve system to magnify the displacement generated from the piezostack actuator. After explaining the operating principle of the proposed piezostack-driven single-stage valve system, the geometric dimensions and mechanical properties of the valve components are discussed in details. An experimental apparatus is then manufactured to evaluate the performances of the valve system such as flow rate. The experimental apparatus consists of a heat chamber, which can regulate the temperature of the valve system and oil, pneumatic-hydraulic cylinders, a hydraulic circuit, a pneumatic circuit, electronic devices, an interface card, and a high voltage amplifier. The pneumatic-hydraulic cylinder transforms the pneumatic pressure into hydraulic pressure. The performances of the valve system regarding spool response, pressure drop, and flow rate are evaluated and presented. In addition, the performance of the valve system under high temperature condition is compared with that under room temperature condition. The experimental results are plotted in both frequency and time domains.

Performance evaluation of a piezoactuator-based single-stage valve system subjected to high temperature

International Nuclear Information System (INIS)

Jeon, Juncheol; Han, Chulhee; Ung Chung, Jye; Choi, Seung-Bok

2015-01-01

In this paper, a novel single-stage valve system activated by a piezostack actuator is proposed and experimentally evaluated at both room temperature (20 °C) and high temperature (100 °C) conditions. A hinge-lever displacement amplifier is adopted in the valve system to magnify the displacement generated from the piezostack actuator. After explaining the operating principle of the proposed piezostack-driven single-stage valve system, the geometric dimensions and mechanical properties of the valve components are discussed in details. An experimental apparatus is then manufactured to evaluate the performances of the valve system such as flow rate. The experimental apparatus consists of a heat chamber, which can regulate the temperature of the valve system and oil, pneumatic-hydraulic cylinders, a hydraulic circuit, a pneumatic circuit, electronic devices, an interface card, and a high voltage amplifier. The pneumatic-hydraulic cylinder transforms the pneumatic pressure into hydraulic pressure. The performances of the valve system regarding spool response, pressure drop, and flow rate are evaluated and presented. In addition, the performance of the valve system under high temperature condition is compared with that under room temperature condition. The experimental results are plotted in both frequency and time domains. (paper)

Conceptual design of helium experimental loop

International Nuclear Information System (INIS)

Yu Xingfu; Feng Kaiming

2007-01-01

In a future demonstration fusion power station (DEMO), helium is envisaged as coolant for plasma facing components, such as blanket and dive,or. All these components have a very complex geometry, with many parallel cooling channels, involving a complex helium flow distribution. Test blanket modules (TBM) of this concept will under go various tests in the experimental reactor ITER. For the qualification of TBM, it is indispensable to test mock-ups in a helium loop under realistic pressure and temperature profiles, in order to validate design codes, especially regarding mass flow and heat transition processes in narrow cooling channels. Similar testing must be performed for DEMO blanket, currently under development. A Helium Experimental Loop (HELOOP) is planed to be built for TBM tests. The design parameter of temperature, pressure, flow rate is 550 degree C, 10 MPa, l kg/s respectively. In particular, HELOOP is able to: perform full-scale tests of TBM under realistic conditions; test other components of the He-cooling system in ITER; qualify the purification circuit; obtain information for the design of the ITER cooling system. The main requirements and characteristics of the HELOOP facility and a preliminary conceptual design are described in the paper. (authors)

Neural Network Assisted Experimental Designs for Food Research

Directory of Open Access Journals (Sweden)

H.S. Ramaswamy

2000-06-01

Full Text Available The ability of artificial neural networks (ANN in predicting full factorial data from the fractional data corresponding to some of the commonly used experimental designs is explored in this paper. Factorial and fractional factorial designs such as L8, L9, L18, and Box and Behnken schemes were considered both in their original form and with some variations (L8+6, L15 and L9+1. Full factorial (3 factors x 5 levels and fractional data were generated employing sixteen different mathematical equations (four in each category: linear, with and without interactions, and non-linear, with and without interactions. Different ANN models were trained and the best model was chosen for each equation based on their ability to predict the fractional data. The best experimental design was then chosen based on their ability to simulate the full- factorial data for each equation. In several cases, the mean relative errors with the L18 design (which had more input data than other models were even higher than with other smaller fractional design. In general, the ANN assisted Lm, Box and Behnken, L15 and L18 designs were found to predict the full factorial data reasonably well with errors less than 5 %. The L8+6 model performed well with several experimental datasets reported in the literature.

Experimental designs for autoregressive models applied to industrial maintenance

International Nuclear Information System (INIS)

Amo-Salas, M.; López-Fidalgo, J.; Pedregal, D.J.

2015-01-01

Some time series applications require data which are either expensive or technically difficult to obtain. In such cases scheduling the points in time at which the information should be collected is of paramount importance in order to optimize the resources available. In this paper time series models are studied from a new perspective, consisting in the use of Optimal Experimental Design setup to obtain the best times to take measurements, with the principal aim of saving costs or discarding useless information. The model and the covariance function are expressed in an explicit form to apply the usual techniques of Optimal Experimental Design. Optimal designs for various approaches are computed and their efficiencies are compared. The methods working in an application of industrial maintenance of a critical piece of equipment at a petrochemical plant are shown. This simple model allows explicit calculations in order to show openly the procedure to find the correlation structure, needed for computing the optimal experimental design. In this sense the techniques used in this paper to compute optimal designs may be transferred to other situations following the ideas of the paper, but taking into account the increasing difficulty of the procedure for more complex models. - Highlights: • Optimal experimental design theory is applied to AR models to reduce costs. • The first observation has an important impact on any optimal design. • Either the lack of precision or small starting observations claim for large times. • Reasonable optimal times were obtained relaxing slightly the efficiency. • Optimal designs were computed in a predictive maintenance context

Learning Layouts for Single-Page Graphic Designs.

Science.gov (United States)

O'Donovan, Peter; Agarwala, Aseem; Hertzmann, Aaron

2014-08-01

This paper presents an approach for automatically creating graphic design layouts using a new energy-based model derived from design principles. The model includes several new algorithms for analyzing graphic designs, including the prediction of perceived importance, alignment detection, and hierarchical segmentation. Given the model, we use optimization to synthesize new layouts for a variety of single-page graphic designs. Model parameters are learned with Nonlinear Inverse Optimization (NIO) from a small number of example layouts. To demonstrate our approach, we show results for applications including generating design layouts in various styles, retargeting designs to new sizes, and improving existing designs. We also compare our automatic results with designs created using crowdsourcing and show that our approach performs slightly better than novice designers.

Engineering Single-Atom Cobalt Catalysts toward Improved Electrocatalysis.

Science.gov (United States)

Wan, Gang; Yu, Pengfei; Chen, Hangrong; Wen, Jianguo; Sun, Cheng-Jun; Zhou, Hua; Zhang, Nian; Li, Qianru; Zhao, Wanpeng; Xie, Bing; Li, Tao; Shi, Jianlin

2018-04-01

The development of cost-effective catalysts to replace noble metal is attracting increasing interests in many fields of catalysis and energy, and intensive efforts are focused on the integration of transition-metal sites in carbon as noble-metal-free candidates. Recently, the discovery of single-atom dispersed catalyst (SAC) provides a new frontier in heterogeneous catalysis. However, the electrocatalytic application of SAC is still subject to several theoretical and experimental limitations. Further advances depend on a better design of SAC through optimizing its interaction with adsorbates during catalysis. Here, distinctive from previous studies, favorable 3d electronic occupation and enhanced metal-adsorbates interactions in single-atom centers via the construction of nonplanar coordination is achieved, which is confirmed by advanced X-ray spectroscopic and electrochemical studies. The as-designed atomically dispersed cobalt sites within nonplanar coordination show significantly improved catalytic activity and selectivity toward the oxygen reduction reaction, approaching the benchmark Pt-based catalysts. More importantly, the illustration of the active sites in SAC indicates metal-natured catalytic sites and a media-dependent catalytic pathway. Achieving structural and electronic engineering on SAC that promotes its catalytic performances provides a paradigm to bridge the gap between single-atom catalysts design and electrocatalytic applications. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Design of single piece sabot for a single stage gas gun

Science.gov (United States)

Vemparala, Vignesh; Mathew, Arun Tom; Rao Koka, Tirumala

2017-11-01

Single piece sabot is a vital part in single stage gas guns for impact testing in aerospace industries. Depending on the type of projectile used the design of sabot varies to accommodate the testing equipment. The velocity of the projectile exiting the barrel is dependent on the material and shape of the sabot used. The material selected for the design of sabot is rigid polyurethane foam, due to their low elastic modulus and low density. Two samples of rigid PU foam is taken and tests are performed to get their exact material properties. These properties are incorporated in numerical simulation to determine the best fit for practical use. Since the PU foams has a wide range of porosity which plays a prominent role in deciding the exit velocity and accuracy of the projectile coming out of the barrel. By optimisation, to the best suitable material sample can be determined.

Experimental investigation of submerged single jet impingement using Cu–water nanofluid

International Nuclear Information System (INIS)

Li Qiang; Xuan Yimin; Yu Feng

2012-01-01

Jet impingement cooling is a vital technique for thermal management of electronic devices of high-heat-flux by impinging fluid on a heater surface due to its high local heat transfer rates. In this paper, two types of Cu–water nanofluids (Cu particles with 25 nm diameter or 100 nm) are introduced into submerged single jet impingement cooling system as the working fluid. The heat transfer features of the nanofluids were experimentally investigated. The effects of the nanoparticle concentration, Reynolds number, nozzle-to-plate distance, fluid temperature, and nanoparticle diameter on the heat transfer performances of the jet impingement of nanofluids are discussed. The experimental results show that the suspended nanoparticles remarkably increase the convective heat transfer coefficient of the base fluid. The convective heat transfer coefficient of Cu–water nanofluid with the volume fraction of 3.0% has 52% higher than the pure water. The experiments also revealed that the suspended nanoparticles brought almost no extra addition of pressure drop in both submerged single jet impingement. In addition, by considering the effects of the suspended nanoparticles as well as the condition of impinging jet, a new heat transfer correlation of nanofluids for the submerged single jet impingement has been proposed. - Highlights: ► Cu–water nanofluids are introduced into submerged single jet impingement. ► The affecting parameters on the heat transfer performances of nanofluids are discussed. ► New heat transfer correlation of nanofluid for single jet impingement is proposed.

An Effective Experimental Optimization Method for Wireless Power Transfer System Design Using Frequency Domain Measurement

Directory of Open Access Journals (Sweden)

Sangyeong Jeong

2017-10-01

Full Text Available This paper proposes an experimental optimization method for a wireless power transfer (WPT system. The power transfer characteristics of a WPT system with arbitrary loads and various types of coupling and compensation networks can be extracted by frequency domain measurements. The various performance parameters of the WPT system, such as input real/imaginary/apparent power, power factor, efficiency, output power and voltage gain, can be accurately extracted in a frequency domain by a single passive measurement. Subsequently, the design parameters can be efficiently tuned by separating the overall design steps into two parts. The extracted performance parameters of the WPT system were validated with time-domain experiments.

Evaluation on Behavior of Single Block Subject to Harmonic Excitation

International Nuclear Information System (INIS)

Choi, Woo-Seok; Kim, Dong-Ok; Park, Keun-Bae; Lee, Won-Jae

2007-01-01

NHDD(Nuclear Hydrogen Development and Demonstration) project team in KAERI(Korea Atomic Energy Research Institute) has been developing a methodology on the seismic evaluation of VHTR(Very High Temperature Reactor). Roughly, there are a block type and a pebble type reactor in VHTR. In the block type reactor, several blocks are stacked and the stacked blocks are arrayed in certain pattern. To evaluate a behavior style and an integrity of the stacked structure subject to a seismic load, a modeling technique to represent the contact surface characteristics between a block and a block support structure and between blocks is necessary. The way to evaluate a load path is also needed. However, it is difficult to deal with a realistic seismic load and to figure out the characteristic of block behavior since it has very complicated time history. In this study, the evaluation of single block subject to a harmonic excitation is conducted for a preliminary evaluation

Research Methods in Healthcare Epidemiology and Antimicrobial Stewardship – Quasi-Experimental Designs

Science.gov (United States)

Schweizer, Marin L.; Braun, Barbara I.; Milstone, Aaron M.

2016-01-01

Quasi-experimental studies evaluate the association between an intervention and an outcome using experiments in which the intervention is not randomly assigned. Quasi-experimental studies are often used to evaluate rapid responses to outbreaks or other patient safety problems requiring prompt non-randomized interventions. Quasi-experimental studies can be categorized into three major types: interrupted time series designs, designs with control groups, and designs without control groups. This methods paper highlights key considerations for quasi-experimental studies in healthcare epidemiology and antimicrobial stewardship including study design and analytic approaches to avoid selection bias and other common pitfalls of quasi-experimental studies. PMID:27267457

Design activities of a fusion experimental breeder

International Nuclear Information System (INIS)

Huang, J.; Feng, K.; Sheng, G.

1999-01-01

The fusion reactor design studies in China are under the support of a fusion-fission hybrid reactor research Program. The purpose of this program is to explore the potential near-term application of fusion energy to support the long-term fusion energy on the one hand and the fission energy development on the other. During 1992-1996 a detailed consistent and integral conceptual design of a Fusion Experimental Breeder, FEB was completed. Beginning from 1996, a further design study towards an Engineering Outline Design of the FEB, FEB-E, has started. The design activities are briefly given. (author)

Design activities of a fusion experimental breeder

International Nuclear Information System (INIS)

Huang, J.; Feng, K.; Sheng, G.

2001-01-01

The fusion reactor design studies in China are under the support of a fusion-fission hybrid reactor research Program. The purpose of this program is to explore the potential near-term application of fusion energy to support the long-term fusion energy on the one hand and the fission energy development on the other. During 1992-1996 a detailed consistent and integral conceptual design of a Fusion Experimental Breeder, FEB was completed. Beginning from 1996, a further design study towards an Engineering Outline Design of the FEB, FEB-E, has started. The design activities are briefly given. (author)

An Introduction to Experimental Design Research

DEFF Research Database (Denmark)

Cash, Philip; Stanković, Tino; Štorga, Mario

2016-01-01

Design research brings together influences from the whole gamut of social, psychological, and more technical sciences to create a tradition of empirical study stretching back over 50 years (Horvath 2004; Cross 2007). A growing part of this empirical tradition is experimental, which has gained in ...

Effects of listening to pleasant music on chronic unilateral neglect: a single-subject study.

Science.gov (United States)

Tsai, Pei-Luen; Chen, Mei-Ching; Huang, Yu-Ting; Lin, Keh-Chung

2013-01-01

Recent studies suggest that the positive emotion induced by pleasant music may improve cognitive functions. We used the single-subject design to study whether listening to preferred music may reduce unilateral neglect in two participants with post-stroke neglect. These participants were instructed to listen to their preferred music every day for 5 weeks, followed by 2 weeks of follow-up assessment. Outcome measures involved the Star Cancellation Test, the Line Bisection Test, and the visual exploration task. A combination of visual analysis and the two-standard-deviation band method was used for data analysis. Both participants showed significant intervention-related improvements on all outcome measures except the Line Bisection Test, on which one participant showed no improvement. The therapeutic effects were maintained during the follow-up phase. The findings suggest that positive emotion, evoked by preferred music, may be used to ameliorate unilateral neglect. Further research using controlled trials is warranted to validate the findings.

Single-case research design in pediatric psychology: considerations regarding data analysis.

Science.gov (United States)

Cohen, Lindsey L; Feinstein, Amanda; Masuda, Akihiko; Vowles, Kevin E

2014-03-01

Single-case research allows for an examination of behavior and can demonstrate the functional relation between intervention and outcome in pediatric psychology. This review highlights key assumptions, methodological and design considerations, and options for data analysis. Single-case methodology and guidelines are reviewed with an in-depth focus on visual and statistical analyses. Guidelines allow for the careful evaluation of design quality and visual analysis. A number of statistical techniques have been introduced to supplement visual analysis, but to date, there is no consensus on their recommended use in single-case research design. Single-case methodology is invaluable for advancing pediatric psychology science and practice, and guidelines have been introduced to enhance the consistency, validity, and reliability of these studies. Experts generally agree that visual inspection is the optimal method of analysis in single-case design; however, statistical approaches are becoming increasingly evaluated and used to augment data interpretation.

Direct experimental observation of nonclassicality in ensembles of single-photon emitters

Science.gov (United States)

Moreva, E.; Traina, P.; Forneris, J.; Degiovanni, I. P.; Ditalia Tchernij, S.; Picollo, F.; Brida, G.; Olivero, P.; Genovese, M.

2017-11-01

In this work we experimentally demonstrate a recently proposed criterion addressed to detect nonclassical behavior in the fluorescence emission of ensembles of single-photon emitters. In particular, we apply the method to study clusters of nitrogen-vacancy centers in diamond characterized with single-photon-sensitive confocal microscopy. Theoretical considerations on the behavior of the parameter at any arbitrary order in the presence of Poissonian noise are presented and, finally, the opportunity of detecting manifold coincidences is discussed.

Comparison of numerical results with experimental data for single-phase natural convection in an experimental sodium loop

International Nuclear Information System (INIS)

Ribando, R.J.

1979-01-01

A comparison is made between computed results and experimental data for single-phase natural convection in an experimental sodium loop. The tests were conducted in the Thermal-Hydraulic Out-of-Reactor Safety (THORS) Facility, an engineering-scale high temperature sodium facility at the Oak Ridge National Laboratory used for thermal-hydraulic testing of simulated LMFBR subassemblies at normal and off-normal operating conditions. Heat generation in the 19 pin assembly during these tests was typical of decay heat levels. Tests were conducted both with zero initial forced flow and with a small initial forced flow. The bypass line was closed in most tests, but open in one. The computer code used to analyze these tests [LONAC (LOw flow and NAtural Convection)] is an ORNL-developed, fast running, one-dimensional, single-phase finite difference model for simulating forced and free convection transients in the THORS loop

Design and analysis of linear oscillatory single-phase permanent magnet generator for free-piston stirling engine systems

Directory of Open Access Journals (Sweden)

Jeong-Man Kim

2017-05-01

Full Text Available This study focuses on the design and analysis of a linear oscillatory single-phase permanent magnet generator for free-piston stirling engine (FPSE systems. In order to implement the design of linear oscillatory generator (LOG for suitable FPSEs, we conducted electromagnetic analysis of LOGs with varying design parameters. Then, detent force analysis was conducted using assisted PM. Using the assisted PM gave us the advantage of using mechanical strength by detent force. To improve the efficiency, we conducted characteristic analysis of eddy-current loss with respect to the PM segment. Finally, the experimental result was analyzed to confirm the prediction of the FEA.

Status of experimental data for the VHTR core design

Energy Technology Data Exchange (ETDEWEB)

Park, Won Seok; Chang, Jong Hwa; Park, Chang Kue

2004-05-01

The VHTR (Very High Temperature Reactor) is being emerged as a next generation nuclear reactor to demonstrate emission-free nuclear-assisted electricity and hydrogen production. The VHTR could be either a prismatic or pebble type helium cooled, graphite moderated reactor. The final decision will be made after the completion of the pre-conceptual design for each type. For the pre-conceptual design for both types, computational tools are being developed. Experimental data are required to validate the tools to be developed. Many experiments on the HTGR (High Temperature Gas-cooled Reactor) cores have been performed to confirm the design data and to validate the design tools. The applicability and availability of the existing experimental data have been investigated for the VHTR core design in this report.

Statistical experimental design for saltstone mixtures

International Nuclear Information System (INIS)

Harris, S.P.; Postles, R.L.

1991-01-01

We used a mixture experimental design for determining a window of operability for a process at the Savannah River Site Defense Waste Processing Facility (DWPF). The high-level radioactive waste at the Savannah River Site is stored in large underground carbon steel tanks. The waste consists of a supernate layer and a sludge layer. 137 Cs will be removed from the supernate by precipitation and filtration. After further processing, the supernate layer will be fixed as a grout for disposal in concrete vaults. The remaining precipitate will be processed at the DWPF with treated waste tank sludge and glass-making chemicals into borosilicate glass. The leach rate properties of the supernate grout, formed from various mixes of solidified salt waste, needed to be determined. The effective diffusion coefficients for NO 3 and Cr were used as a measure of leach rate. Various mixes of cement, Ca(OH) 2 , salt, slag and flyash were used. These constituents comprise the whole mix. Thus, a mixture experimental design was used

Fast Bayesian experimental design: Laplace-based importance sampling for the expected information gain

KAUST Repository

Beck, Joakim

2018-02-19

In calculating expected information gain in optimal Bayesian experimental design, the computation of the inner loop in the classical double-loop Monte Carlo requires a large number of samples and suffers from underflow if the number of samples is small. These drawbacks can be avoided by using an importance sampling approach. We present a computationally efficient method for optimal Bayesian experimental design that introduces importance sampling based on the Laplace method to the inner loop. We derive the optimal values for the method parameters in which the average computational cost is minimized for a specified error tolerance. We use three numerical examples to demonstrate the computational efficiency of our method compared with the classical double-loop Monte Carlo, and a single-loop Monte Carlo method that uses the Laplace approximation of the return value of the inner loop. The first demonstration example is a scalar problem that is linear in the uncertain parameter. The second example is a nonlinear scalar problem. The third example deals with the optimal sensor placement for an electrical impedance tomography experiment to recover the fiber orientation in laminate composites.

Fast Bayesian experimental design: Laplace-based importance sampling for the expected information gain

Science.gov (United States)

Beck, Joakim; Dia, Ben Mansour; Espath, Luis F. R.; Long, Quan; Tempone, Raúl

2018-06-01

In calculating expected information gain in optimal Bayesian experimental design, the computation of the inner loop in the classical double-loop Monte Carlo requires a large number of samples and suffers from underflow if the number of samples is small. These drawbacks can be avoided by using an importance sampling approach. We present a computationally efficient method for optimal Bayesian experimental design that introduces importance sampling based on the Laplace method to the inner loop. We derive the optimal values for the method parameters in which the average computational cost is minimized according to the desired error tolerance. We use three numerical examples to demonstrate the computational efficiency of our method compared with the classical double-loop Monte Carlo, and a more recent single-loop Monte Carlo method that uses the Laplace method as an approximation of the return value of the inner loop. The first example is a scalar problem that is linear in the uncertain parameter. The second example is a nonlinear scalar problem. The third example deals with the optimal sensor placement for an electrical impedance tomography experiment to recover the fiber orientation in laminate composites.

Subjective knowledge and fear appeal effectiveness: implications for message design.

Science.gov (United States)

Nabi, Robin L; Roskos-Ewoldsen, David; Carpentier, Francesca Dillman

2008-01-01

This research investigates the role of perceived health knowledge on the effectiveness of fear-based persuasive appeals. Undergraduates (N = 263) read a strong fear, weak fear, or efficacy-only message encouraging breast or testicular self-examination. As expected, results indicated that men high in subjective knowledge were less reactant and more persuaded by the efficacy-only message whereas those low in subjective knowledge did not evidence this pattern. Contrary to expectation, women high in subjective knowledge had comparable reactions to each of the 3 messages. Implications for fear appeal theory and message design are discussed.

Experimental site and design

Energy Technology Data Exchange (ETDEWEB)

Guenette, C. C. [SINTEF Applied Cemistry, Trondheim (Norway)

1999-08-01

Design and site selection criteria for the Svalbard oil spill experiments are described. All three experimental sites have coarse and mixed sediment beaches of sand and pebble; within each site wave exposure is very similar; along-shore and across-shore sediment characteristics are also relatively homogeneous. Tidal range is in the order of 0.6 m at neaps, and 1.8 m at springs. All three sites are open to wave action and are ice-free during the experimental period of mid-July to mid-October. Study plots at each site were selected for different treatments from within the continuous stretch of oiled shoreline, with oiled buffer zones between plots and at either end of the oiled zone. Treatments included mixing (tilling), sediment relocation (surf washing) and bioremediation (nutrient enrichment). Measurements and observations were carried out during the summers of 1997 and 1998. The characteristics measured were: wave and wind conditions; beach topography and elevation; sediment grain size distribution; mineral fines size distribution and mineral composition; background hydrocarbons; concentration of oil within experimental plots and the rate of oil loss over time; depth of oil penetration and thickness of the oiled sediment layer; oil concentration and toxicity of near-shore benthic sediments; mineral composition of suspended particulate material captured in sub-tidal sediment traps; and oil-fines interaction in near-shore water samples. 1 fig.

Experimental site and design

Energy Technology Data Exchange (ETDEWEB)

Guenette, C. C. [SINTEF Applied Cemistry, Trondheim (Norway)

1999-07-01

Design and site selection criteria for the Svalbard oil spill experiments are described. All three experimental sites have coarse and mixed sediment beaches of sand and pebble; within each site waveexposure is very similar; along-shore and across-shore sediment characteristics are also relatively homogeneous. Tidal range is in the order of 0.6 m at neaps, and 1.8 m at springs. All three sites are open to wave action and are ice-free during the experimental period of mid-July to mid-October. Study plots at each site were selected for different treatments from within the continuous stretch of oiled shoreline, with oiled buffer zones between plots and at either end of the oiled zone. Treatments included mixing (tilling), sediment relocation (surf washing) and bioremediation (nutrient enrichment). Measurements and observations were carried out during the summers of 1997 and 1998. The characteristics measured were: wave and wind conditions; beach topography and elevation; sediment grain size distribution; mineral fines size distribution and mineral composition; background hydrocarbons; concentration of oil within experimental plots and the rate of oil loss over time; depth of oil penetration and thickness of the oiled sediment layer; oil concentration and toxicity of near-shore benthic sediments; mineral composition of suspended particulate material captured in sub-tidal sediment traps; and oil-fines interaction in near-shore water samples. 1 fig.

Numerical and Experimental Analysis of Aircraft Wing Subjected to Fatigue Loading

Directory of Open Access Journals (Sweden)

Hatem Rahim Wasmi

2016-10-01

Full Text Available This study deals with the aircraft wing analysis (numerical and experimental which subjected to fatigue loading in order to analyze the aircraft wing numerically by using ANSYS 15.0 software and experimentally by using loading programs which effect on fatigue test specimens at laboratory to estimate life of used metal (aluminum alloy 7075-T651 the wing metal and compare between numerical and experimental work, as well as to formulate an experimental mathematical model which may find safe estimate for metals and most common alloys that are used to build aircraft wing at certain conditions. In experimental work, a (34 specimen of (aluminum alloy 7075-T651 were tested using alternating bending fatigue machine rig. The test results are ; (18 Specimen to establish the (S-N curve and endurance limit and the other specimens used for variable amplitude tests were represented by loading programs which represents actual flight conditions. Also it has been obtained the safe fatigue curves which are described by mathematical formulas. ANSYS results show convergence with experimental results about cumulative fatigue damage (D, a mathematical model is proposed to estimate the life; this model gives good results in case of actual loading programs. Also, Miner and Marsh rules are applied to the specimens and compared with the proposal mathematical model in order to estimate the life of the wing material under actual flight loading conditions, comparing results show that it is possible to depend on present mathematical model than Miner and Marsh theories because the proposal mathematical model shows safe and good results compared with experimental work results.

design, construction and measured performance of a single-stage

African Journals Online (AJOL)

2012-11-03

Nov 3, 2012 ... Abstract. The design philosophy, construction and measured performances of a single stage, single entry centrifugal pump .... the tachometer spindle to be held against a recess in the motor shaft. The constructed centrifugal ...

A Simulation Study of Threats to Validity in Quasi-Experimental Designs: Interrelationship between Design, Measurement, and Analysis.

Science.gov (United States)

Holgado-Tello, Fco P; Chacón-Moscoso, Salvador; Sanduvete-Chaves, Susana; Pérez-Gil, José A

2016-01-01

The Campbellian tradition provides a conceptual framework to assess threats to validity. On the other hand, different models of causal analysis have been developed to control estimation biases in different research designs. However, the link between design features, measurement issues, and concrete impact estimation analyses is weak. In order to provide an empirical solution to this problem, we use Structural Equation Modeling (SEM) as a first approximation to operationalize the analytical implications of threats to validity in quasi-experimental designs. Based on the analogies established between the Classical Test Theory (CTT) and causal analysis, we describe an empirical study based on SEM in which range restriction and statistical power have been simulated in two different models: (1) A multistate model in the control condition (pre-test); and (2) A single-trait-multistate model in the control condition (post-test), adding a new mediator latent exogenous (independent) variable that represents a threat to validity. Results show, empirically, how the differences between both the models could be partially or totally attributed to these threats. Therefore, SEM provides a useful tool to analyze the influence of potential threats to validity.

System design overview of JAXA small supersonic experimental airplane (NEXST-1)

OpenAIRE

Takami, Hikaru; 高見　光

2007-01-01

The system of JAXA small supersonic experimental airplane (NEXST-1: National EXperimental Supersonic Transport-1) has been briefly explained. Some design problems that the designers have encountered have also been briefly explained.

Quasi-experimental study designs series-paper 7: assessing the assumptions.

Science.gov (United States)

Bärnighausen, Till; Oldenburg, Catherine; Tugwell, Peter; Bommer, Christian; Ebert, Cara; Barreto, Mauricio; Djimeu, Eric; Haber, Noah; Waddington, Hugh; Rockers, Peter; Sianesi, Barbara; Bor, Jacob; Fink, Günther; Valentine, Jeffrey; Tanner, Jeffrey; Stanley, Tom; Sierra, Eduardo; Tchetgen, Eric Tchetgen; Atun, Rifat; Vollmer, Sebastian

2017-09-01

Quasi-experimental designs are gaining popularity in epidemiology and health systems research-in particular for the evaluation of health care practice, programs, and policy-because they allow strong causal inferences without randomized controlled experiments. We describe the concepts underlying five important quasi-experimental designs: Instrumental Variables, Regression Discontinuity, Interrupted Time Series, Fixed Effects, and Difference-in-Differences designs. We illustrate each of the designs with an example from health research. We then describe the assumptions required for each of the designs to ensure valid causal inference and discuss the tests available to examine the assumptions. Copyright © 2017 Elsevier Inc. All rights reserved.

Design and experimental characterization of a NiTi-based, high-frequency, centripetal peristaltic actuator

International Nuclear Information System (INIS)

Borlandelli, E; Scarselli, D; Bettini, P; Morandini, M; Sala, G; Quadrio, M; Nespoli, A; Rigamonti, D; Villa, E

2015-01-01

Development and experimental testing of a peristaltic device actuated by a single shape-memory NiTi wire are described. The actuator is designed to radially shrink a compliant silicone pipe, and must work on a sustained basis at an actuation frequency that is higher than those typical of NiTi actuators. Four rigid, aluminum-made circular sectors are sitting along the pipe circumference and provide the required NiTi wire housing. The aluminum assembly acts as geometrical amplifier of the wire contraction and as heat sink required to dissipate the thermal energy of the wire during the cooling phase. We present and discuss the full experimental investigation of the actuator performance, measured in terms of its ability to reduce the pipe diameter, at a sustained frequency of 1.5 Hz. Moreover, we investigate how the diameter contraction is affected by various design parameters as well as actuation frequencies up to 4 Hz. We manage to make the NiTi wire work at 3% in strain, cyclically providing the designed pipe wall displacement. The actuator performance is found to decay approximately linearly with actuation frequencies up to 4 Hz. Also, the interface between the wire and the aluminum parts is found to be essential in defining the functional performance of the actuator. (paper)

SSD for R: A Comprehensive Statistical Package to Analyze Single-System Data

Science.gov (United States)

Auerbach, Charles; Schudrich, Wendy Zeitlin

2013-01-01

The need for statistical analysis in single-subject designs presents a challenge, as analytical methods that are applied to group comparison studies are often not appropriate in single-subject research. "SSD for R" is a robust set of statistical functions with wide applicability to single-subject research. It is a comprehensive package…

Design of a hybrid double-sideband/single-sideband (schlieren) objective aperture suitable for electron microscopy

Energy Technology Data Exchange (ETDEWEB)

Buijsse, Bart; Laarhoven, Frank M.H.M. van [FEI Company, PO Box 80066, 5600 KA Eindhoven (Netherlands); Schmid, Andreas K.; Cambie, Rossana; Cabrini, Stefano; Jin, Jian [Lawrence Berkeley National Laboratory, University of California, Berkeley, CA 94720 (United States); Glaeser, Robert M., E-mail: rmglaeser@lbl.gov [Lawrence Berkeley National Laboratory, University of California, Berkeley, CA 94720 (United States)

2011-12-15

A novel design is described for an aperture that blocks a half-plane of the electron diffraction pattern out to a desired scattering angle, and then - except for a narrow support beam - transmits all of the scattered electrons beyond that angle. Our proposed tulip-shaped design is thus a hybrid between the single-sideband (ssb) aperture, which blocks a full half-plane of the diffraction pattern, and the conventional (i.e. fully open) double-sideband (dsb) aperture. The benefits of this hybrid design include the fact that such an aperture allows one to obtain high-contrast images of weak-phase objects with the objective lens set to Scherzer defocus. We further demonstrate that such apertures can be fabricated from thin-foil materials by milling with a focused ion beam (FIB), and that such apertures are fully compatible with the requirements of imaging out to a resolution of at least 0.34 nm. As is known from earlier work with single-sideband apertures, however, the edge of such an aperture can introduce unwanted, electrostatic phase shifts due to charging. The principal requirement for using such an aperture in a routine data-collection mode is thus to discover appropriate materials, protocols for fabrication and processing and conditions of use such that the hybrid aperture remains free of charging over long periods of time. -- Highlights: Black-Right-Pointing-Pointer New objective-aperture design is proposed for imaging weak-phase objects. Black-Right-Pointing-Pointer Design produces single-sideband contrast at low spatial frequencies. Black-Right-Pointing-Pointer Design also retains Scherzer-defocus phase contrast at higher resolution. Black-Right-Pointing-Pointer Proof-of-concept results are presented for microfabricated apertures. Black-Right-Pointing-Pointer Charging of such apertures during use remains an experimental challenge.

Optimal Experimental Design for Model Discrimination

Science.gov (United States)

Myung, Jay I.; Pitt, Mark A.

2009-01-01

Models of a psychological process can be difficult to discriminate experimentally because it is not easy to determine the values of the critical design variables (e.g., presentation schedule, stimulus structure) that will be most informative in differentiating them. Recent developments in sampling-based search methods in statistics make it…

Predicting variation in subject thermal response during transcranial magnetic resonance guided focused ultrasound surgery: Comparison in seventeen subject datasets

Energy Technology Data Exchange (ETDEWEB)

Vyas, Urvi, E-mail: urvi.vyas@gmail.com; Ghanouni, Pejman; Halpern, Casey H.; Pauly, Kim Butts [Department of Radiology, Stanford University, Stanford, California 94305 (United States); Elias, Jeff [Department of Neurological Surgery, University of Virginia, Charlottesville, Virginia 22908 (United States)

2016-09-15

Purpose: In transcranial magnetic resonance-guided focused ultrasound (tcMRgFUS) treatments, the acoustic and spatial heterogeneity of the skull cause reflection, absorption, and scattering of the acoustic beams. These effects depend on skull-specific parameters and can lead to patient-specific thermal responses to the same transducer power. In this work, the authors develop a simulation tool to help predict these different experimental responses using 3D heterogeneous tissue models based on the subject CT images. The authors then validate and compare the predicted skull efficiencies to an experimental metric based on the subject thermal responses during tcMRgFUS treatments in a dataset of seventeen human subjects. Methods: Seventeen human head CT scans were used to create tissue acoustic models, simulating the effects of reflection, absorption, and scattering of the acoustic beam as it propagates through a heterogeneous skull. The hybrid angular spectrum technique was used to model the acoustic beam propagation of the InSightec ExAblate 4000 head transducer for each subject, yielding maps of the specific absorption rate (SAR). The simulation assumed the transducer was geometrically focused to the thalamus of each subject, and the focal SAR at the target was used as a measure of the simulated skull efficiency. Experimental skull efficiency for each subject was calculated using the thermal temperature maps from the tcMRgFUS treatments. Axial temperature images (with no artifacts) were reconstructed with a single baseline, corrected using a referenceless algorithm. The experimental skull efficiency was calculated by dividing the reconstructed temperature rise 8.8 s after sonication by the applied acoustic power. Results: The simulated skull efficiency using individual-specific heterogeneous models predicts well (R{sup 2} = 0.84) the experimental energy efficiency. Conclusions: This paper presents a simulation model to predict the variation in thermal responses

Using IMPRINT to Guide Experimental Design with Simulated Task Environments

Science.gov (United States)

2015-06-18

USING IMPRINT TO GUIDE EXPERIMENTAL DESIGN OF SIMULATED TASK ENVIRONMENTS THESIS Gregory...ENG-MS-15-J-052 USING IMPRINT TO GUIDE EXPERIMENTAL DESIGN WITH SIMULATED TASK ENVIRONMENTS THESIS Presented to the Faculty Department...Civilian, USAF June 2015 DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. AFIT-ENG-MS-15-J-052 USING IMPRINT

The semantic variant of primary progressive aphasia: clinical and neuroimaging evidence in single subjects.

Directory of Open Access Journals (Sweden)

Leonardo Iaccarino

Full Text Available We present a clinical-neuroimaging study in a series of patients with a clinical diagnosis of semantic variant of primary progressive aphasia (svPPA, with the aim to provide clinical-functional correlations of the cognitive and behavioral manifestations at the single-subject level.We performed neuropsychological investigations, 18F-FDG-PET single-subject and group analysis, with an optimized SPM voxel-based approach, and correlation analyses. A measurement of white matter integrity by means of diffusion tensor imaging (DTI was also available for a subgroup of patients.Cognitive assessment confirmed the presence of typical semantic memory deficits in all patients, with a relative sparing of executive, attentional, visuo-constructional, and episodic memory domains. 18F-FDG-PET showed a consistent pattern of cerebral hypometabolism across all patients, which correlated with performance in semantic memory tasks. In addition, a majority of patients also presented with behavioral disturbances associated with metabolic dysfunction in limbic structures. In a subgroup of cases the DTI analysis showed FA abnormalities in the inferior longitudinal and uncinate fasciculi.Each svPPA individual had functional derangement involving an extended, connected system within the left temporal lobe, a crucial part of the verbal semantic network, as well as an involvement of limbic structures. The latter was associated with behavioral manifestations and extended beyond the area of atrophy shown by CT scan.Single-subject 18F-FDG-PET analysis can account for both cognitive and behavioral alterations in svPPA. This provides useful support to the clinical diagnosis.

Optimizing an experimental design for an electromagnetic experiment

Science.gov (United States)

Roux, Estelle; Garcia, Xavier

2013-04-01

Most of geophysical studies focus on data acquisition and analysis, but another aspect which is gaining importance is the discussion on acquisition of suitable datasets. This can be done through the design of an optimal experiment. Optimizing an experimental design implies a compromise between maximizing the information we get about the target and reducing the cost of the experiment, considering a wide range of constraints (logistical, financial, experimental …). We are currently developing a method to design an optimal controlled-source electromagnetic (CSEM) experiment to detect a potential CO2 reservoir and monitor this reservoir during and after CO2 injection. Our statistical algorithm combines the use of linearized inverse theory (to evaluate the quality of one given design via the objective function) and stochastic optimization methods like genetic algorithm (to examine a wide range of possible surveys). The particularity of our method is that it uses a multi-objective genetic algorithm that searches for designs that fit several objective functions simultaneously. One main advantage of this kind of technique to design an experiment is that it does not require the acquisition of any data and can thus be easily conducted before any geophysical survey. Our new experimental design algorithm has been tested with a realistic one-dimensional resistivity model of the Earth in the region of study (northern Spain CO2 sequestration test site). We show that a small number of well distributed observations have the potential to resolve the target. This simple test also points out the importance of a well chosen objective function. Finally, in the context of CO2 sequestration that motivates this study, we might be interested in maximizing the information we get about the reservoir layer. In that case, we show how the combination of two different objective functions considerably improve its resolution.

Design and Experimental Study on Spinning Solid Rocket Motor

Science.gov (United States)

Xue, Heng; Jiang, Chunlan; Wang, Zaicheng

The study on spinning solid rocket motor (SRM) which used as power plant of twice throwing structure of aerial submunition was introduced. This kind of SRM which with the structure of tangential multi-nozzle consists of a combustion chamber, propellant charge, 4 tangential nozzles, ignition device, etc. Grain design, structure design and prediction of interior ballistic performance were described, and problem which need mainly considered in design were analyzed comprehensively. Finally, in order to research working performance of the SRM, measure pressure-time curve and its speed, static test and dynamic test were conducted respectively. And then calculated values and experimental data were compared and analyzed. The results indicate that the designed motor operates normally, and the stable performance of interior ballistic meet demands. And experimental results have the guidance meaning for the pre-research design of SRM.

Pharmacokinetics and Safety of Intravenous Murepavadin Infusion in Healthy Adult Subjects Administered Single and Multiple Ascending Doses.

Science.gov (United States)

Wach, Achim; Dembowsky, Klaus; Dale, Glenn E

2018-04-01

Murepavadin is the first in class of the outer membrane protein-targeting antibiotics (OMPTA) and a pathogen-specific peptidomimetic antibacterial with a novel, nonlytic mechanism of action targeting Pseudomonas aeruginosa Murepavadin is being developed for the treatment of hospital-acquired bacterial pneumonia (HABP) and ventilator-associated bacterial pneumonia (VABP). The pharmacokinetics (PK) and safety of single and multiple doses of murepavadin were investigated in healthy male subjects. Part A of the study was a double-blind, randomized, placebo-controlled, single-ascending-dose investigation in 10 sequential cohorts where each cohort comprised 6 healthy male subjects; 4 subjects were randomized to murepavadin, and 2 subjects were randomized to placebo. Part B was a double-blind, randomized, placebo-controlled, multiple-ascending-dose investigation in 3 sequential cohorts. After a single dose of murepavadin, the geometric mean half-life (2.52 to 5.30 h), the total clearance (80.1 to 114 ml/h/kg), and the volume of distribution (415 to 724 ml/kg) were consistent across dose levels. The pharmacokinetics of the dosing regimens evaluated were dose proportional and linear. Murepavadin was well tolerated, adverse events were transient and generally mild, and no dose-limiting toxicity was identified. Copyright © 2018 American Society for Microbiology.

Design of flapping wings for application to single active degree of freedom micro air vehicles

Science.gov (United States)

Chang, Kelvin Thomas

This dissertation covers an experimental program to understand how wing compliance influences the performance of flapping micro air vehicle wings. The focus is the design of a membraned flapping wing for a single active degree of freedom mechanism, looking to maximize thrust performance in hover conditions. The optimization approach is unique in that experiments were the chosen engine as opposed to a computation model; this is because of the complexity involved in hover-mode flapping aerodynamics. The flapping mechanism and manufacturing process for fabricating the wings were carefully developed. The uncertainty in the thrust measurement was identified and reduced by implementing precision machining and repeatable techniques for fabrication. This resulted in a reduction of the manufacturing coefficient of variation from 16.8% to 2.6%. Optimization was then conducted for a single objective (Maximize thrust), using a three parameter design space, finding the highest thrust performance in wings with high aspect ratio; then, a multi-objective optimization was conducted with two objectives (Thrust and Power) and a four parameter space. The research then shifted focus to identifying the stiffness and deformation characteristics of high performance wing designs. Static stiffness measurements with a simple line load suggested that high chordwise stiffness or lower spanwise stiffness would be favorable for aerodynamic performance. To explore more components of the deformation, a full-field imaging technique was used and a uniform load was substituted to engage with the membrane. It was found that there is a range of torsional compliance where the wing is most efficient especially at higher flapping frequencies. The final component of the study was the dynamic deformation measurement. The two system, four camera digital image correlation setup uses stroboscopic measurement to capture the wing deformation. The phase shift between the twist and stroke, and the tip deflection

Early results from an experimental program to determine the behavior of containment piping penetration bellows subjected to severe accident conditions

International Nuclear Information System (INIS)

Lambert, L.D.; Parks, M.B.

1994-01-01

Containment piping penetration bellows are an integral part of the pressure boundary in steel containments in the United States (US). Their purpose is to minimize loading on the containment shell caused by differential movement between the piping and the containment. This differential movement is typically caused by thermal gradients generated during startup and shutdown of the reactor, but can be caused by earthquake, a loss-of-coolant accident (LOCA), or ''severe'' accidents. In the event of a severe accident, the bellows would be subjected to pressure, temperature, and deflection well beyond the design basis. Most bellows are installed such that they would be subjected to elevated internal pressure, elevated temperature, axial compression, and lateral deflection during a severe accident. A few bellows would be subjected to external pressure and axial elongation, as well as elevated temperature and lateral deflection. The purpose of this experimental program is to examine the potential for leakage of containment bellows during a severe accident. The test series subjects bellows to various levels and combinations of internal pressure, elevated temperature, axial compression or elongation, and lateral deformation. The experiments are being conducted in two parts. For Part 1, all bellows specimens are tested in ''like-new'' condition, without regard for the possible degrading effect of corrosion that has been observed in some containment piping bellows in the US Part I testing, which included 13 bellows tests, has been completed. The second part of the experimental program, in which bellows are subjected to simulated corrosive environments prior to testing, has just just begun. The Part I experiments have shown that bellows in ''like-new'' condition can withstand elevated temperatures and pressures along with large deformations before leaking. In most cases, the like-new bellows were fully compressed without developing any leakage

Experimental and simulation studies on a single pass, double duct solar air heater

Energy Technology Data Exchange (ETDEWEB)

Forson, F.K. [Kwame Nkrumah Univ. of Science and Technology, Dept. of Mechanical Engineering, Kumasi (Ghana); Rajakaruna, H. [De Montfort Univ., School of Engineering and Technology, Leicester (United Kingdom)

2003-05-01

A mathematical model of a single pass, double duct solar air heater (SPDDSAH) is described. The model provides a design tool capable of predicting: incident solar radiation, heat transfer coefficients, mean air flow rates, mean air temperature and relative humidity at the exit. Results from the simulation are presented and compared with experimental ones obtained on a full scale air heater and a small scale laboratory one. Reasonable agreement between the predicted and measured values is demonstrated. Predicted results from a parametric study are also presented. It is shown that significant improvement in the SPDDSAH performance can be obtained with an appropriate choice of the collector parameters and the top to bottom channel depth ratio of the two ducts. The air mass flow rate is shown to be the dominant factor in determining the overall efficiency of the heater. (Author)

Conceptual design studies of experimental and demonstration fusion reactors

International Nuclear Information System (INIS)

1978-01-01

Since 1973 the FINTOR Group has been involved in conceptual design studies of TOKAMAK-type fusion reactors to precede the construction of a prototype power reactor plant. FINTOR-1 was the first conceptual design aimed at investigating the main physics and engineering constraints on a minimum-size (both dimensions and thermal power) tokamak experimental reactor. The required plasma energy confinement time as evaluated by various power balance models was compared with the values resulting from different transport models. For the reference design, an energy confinement time ten times smaller than neoclassical was assumed. This also implied a rather high (thermally stable) working temperature (above 20 keV) for the reactor. Other relevant points of the design were: circular plasma cross section, single-null axisymmetric divertor; lithium breeder, stainless steel structures, helium coolant; modular blanket and shield structure; copper-stabilized, superconducting Nb-Ti toroidal field and divertor coils; vertical field and transformer coils inside the toroidal coils; vacuum-tight containment vessel. Solutions involving air and iron transformer cores were compared. These assumptions led to a minimum size reactor with a thermal power of about 100MW and rather large dimensions (major radius of about 9m) similar to those of full-scale power reactors considered in other conceptual studies. The FINTOR-1 analysis was completed by the end of 1976. In 1977 a conceptual design of a Demonstration Power Reactor Plant (FINTOR-D) was started. In this study the main working assumptions differing from those of FINTOR-1 are: non-circular plasma cross section; plasma confinement compatible with trapped ion instabilities; cold (gas) blanket sufficient for wall protection (no divertor); wall loading between 1-3MW/m 2 and thermal power of a few GW. (author)

Temperature measurement and control system for transtibial prostheses: Single subject clinical evaluation.

Science.gov (United States)

Ghoseiri, Kamiar; Zheng, Yong Ping; Leung, Aaron K L; Rahgozar, Mehdi; Aminian, Gholamreza; Masoumi, Mehdi; Safari, Mohammad Reza

2018-01-01

The snug fit of a prosthetic socket over the residual limb can disturb thermal balance and put skin integrity in jeopardy by providing an unpleasant and infectious environment. The prototype of a temperature measurement and control (TM&C) system was previously introduced to resolve thermal problems related to prostheses. This study evaluates its clinical application in a setting with reversal, single subject design. The TM&C system was installed on a fabricated prosthetic socket of a man with unilateral transtibial amputation. Skin temperature of the residual limb without prosthesis at baseline and with prosthesis during rest and walking was evaluated. The thermal sense and thermal comfort of the participant were also evaluated. The results showed different skin temperature around the residual limb with a temperature decrease tendency from proximal to distal. The TM&C system decreased skin temperature rise after prosthesis wearing. The same situation occurred during walking, but the thermal power of the TM&C system was insufficient to overcome heat build-up in some regions of the residual limb. The participant reported no significant change of thermal sense and thermal comfort. Further investigations are warranted to examine thermography pattern of the residual limb, thermal sense, and thermal comfort in people with amputation.

Using virtual reality to distinguish subjects with multiple- but not single-domain amnestic mild cognitive impairment from normal elderly subjects.

Science.gov (United States)

Mohammadi, Alireza; Kargar, Mahmoud; Hesami, Ehsan

2018-03-01

Spatial disorientation is a hallmark of amnestic mild cognitive impairment (aMCI) and Alzheimer's disease. Our aim was to use virtual reality to determine the allocentric and egocentric memory deficits of subjects with single-domain aMCI (aMCIsd) and multiple-domain aMCI (aMCImd). For this purpose, we introduced an advanced virtual reality navigation task (VRNT) to distinguish these deficits in mild Alzheimer's disease (miAD), aMCIsd, and aMCImd. The VRNT performance of 110 subjects, including 20 with miAD, 30 with pure aMCIsd, 30 with pure aMCImd, and 30 cognitively normal controls was compared. Our newly developed VRNT consists of a virtual neighbourhood (allocentric memory) and virtual maze (egocentric memory). Verbal and visuospatial memory impairments were also examined with Rey Auditory-Verbal Learning Test and Rey-Osterrieth Complex Figure Test, respectively. We found that miAD and aMCImd subjects were impaired in both allocentric and egocentric memory, but aMCIsd subjects performed similarly to the normal controls on both tasks. The miAD, aMCImd, and aMCIsd subjects performed worse on finding the target or required more time in the virtual environment than the aMCImd, aMCIsd, and normal controls, respectively. Our findings indicated the aMCImd and miAD subjects, as well as the aMCIsd subjects, were more impaired in egocentric orientation than allocentric orientation. We concluded that VRNT can distinguish aMCImd subjects, but not aMCIsd subjects, from normal elderly subjects. The VRNT, along with the Rey Auditory-Verbal Learning Test and Rey-Osterrieth Complex Figure Test, can be used as a valid diagnostic tool for properly distinguishing different forms of aMCI. © 2018 Japanese Psychogeriatric Society.

Fundamental criteria for the design of high-performance Josephson nondestructive readout random access memory cells and experimental confirmation

International Nuclear Information System (INIS)

Henkels, W.H.

1979-01-01

Fundamental design criteria for Josephson nondestructive readout random access memory (NDRO RAM) cells are presented, within the context of an LSI array environment. Emphasis is placed upon principles which are relevant to high performance. The criteria are elucidated via a specific design which is simulated and then experimentally evaluated in a technology with a smallest critical dimension of 5 μm. The specific cell differs from previously tested Josephson NDRO cells in several respects; namely, the cell stores only approx.8Phi 0 , employs interferometer gates and an external damping resistor, allows switching into device resonances, and eliminates the need for a special initialization cycle. The cell-selection scheme, employing triple coincidence, results in larger operating margins and smaller operating currents than have previously been achieved. The large operating margins and all basic cell design criteria were experimentally verified. The experimental interferometer gate characteristics were analyzed in detail and found to be describable by simple models. In addition, it was discovered that single flux quantum transitions in the interferometer gates could be exploited beneficially in order to enhance the insensitivity of operating margins to fabrication tolerances

Experimental single-chip color HDTV image acquisition system with 8M-pixel CMOS image sensor

Science.gov (United States)

Shimamoto, Hiroshi; Yamashita, Takayuki; Funatsu, Ryohei; Mitani, Kohji; Nojiri, Yuji

2006-02-01

We have developed an experimental single-chip color HDTV image acquisition system using 8M-pixel CMOS image sensor. The sensor has 3840 × 2160 effective pixels and is progressively scanned at 60 frames per second. We describe the color filter array and interpolation method to improve image quality with a high-pixel-count single-chip sensor. We also describe an experimental image acquisition system we used to measured spatial frequency characteristics in the horizontal direction. The results indicate good prospects for achieving a high quality single chip HDTV camera that reduces pseudo signals and maintains high spatial frequency characteristics within the frequency band for HDTV.

Who is the research subject in cluster randomized trials in health research?

Directory of Open Access Journals (Sweden)

Brehaut Jamie C

2011-07-01

Full Text Available Abstract This article is part of a series of papers examining ethical issues in cluster randomized trials (CRTs in health research. In the introductory paper in this series, we set out six areas of inquiry that must be addressed if the CRT is to be set on a firm ethical foundation. This paper addresses the first of the questions posed, namely, who is the research subject in a CRT in health research? The identification of human research subjects is logically prior to the application of protections as set out in research ethics and regulation. Aspects of CRT design, including the fact that in a single study the units of randomization, experimentation, and observation may differ, complicate the identification of human research subjects. But the proper identification of human research subjects is important if they are to be protected from harm and exploitation, and if research ethics committees are to review CRTs efficiently. We examine the research ethics literature and international regulations to identify the core features of human research subjects, and then unify these features under a single, comprehensive definition of human research subject. We define a human research subject as any person whose interests may be compromised as a result of interventions in a research study. Individuals are only human research subjects in CRTs if: (1 they are directly intervened upon by investigators; (2 they interact with investigators; (3 they are deliberately intervened upon via a manipulation of their environment that may compromise their interests; or (4 their identifiable private information is used to generate data. Individuals who are indirectly affected by CRT study interventions, including patients of healthcare providers participating in knowledge translation CRTs, are not human research subjects unless at least one of these conditions is met.

Experimental study of single-vertex $(e^{-}-e^{+})$ pair creation in a crystal

CERN Multimedia

2002-01-01

This experiment will study the newly predicted process of $e^{-}-e^{+}$ pair production by high energy photons incident along major axial direction of a single crystal. This process is based upon the well-known channeling properties of negatively charged particles along atomic rows of a crystal. The $e^{-}-e^{+}$ pair creation may proceed in a one-step process, without violating energy and momentum conversation laws, due to the lowering of the total energy of the channeled electron (Fig. 1). \\\\ \\\\ The pair creation rate should increase with increasing photon energies (above a threshold of a few GeV) and largely exceed the Bethe-Heitler process rate for photon energies of a few tens of GeV. It is also expected that the created particles share the photon energy nearly equally, in contrast with the rather flat energy distribution associated with the Bethe-Heitler process. \\\\ \\\\ The experimental set-up (Fig. 2) is designed for the study of those two features: photon energy dependence of the pair creation rate, an...

Challenges in thermal design of industrial single-phase power inverter

Directory of Open Access Journals (Sweden)

Ninković Predrag

2016-01-01

Full Text Available This paper presents the influence of thermal aspects in design process of an industrial single-phase inverter, choice of its topology and components. Stringent design inputs like very high overload level, demand for natural cooling and very wide input voltage range have made conventional circuit topology inappropriate therefore asking for alternative solution. Different power losses calculations in semiconductors are performed and compared, outlining the guidelines how to choose the final topology. Some recommendations in power magnetic components design are given. Based on the final project, a 20kVA single-phase inverter for thermal power plant supervisory and control system is designed and commissioned.

Design of an omnidirectional single-point photodetector for large-scale spatial coordinate measurement

Science.gov (United States)

Xie, Hongbo; Mao, Chensheng; Ren, Yongjie; Zhu, Jigui; Wang, Chao; Yang, Lei

2017-10-01

In high precision and large-scale coordinate measurement, one commonly used approach to determine the coordinate of a target point is utilizing the spatial trigonometric relationships between multiple laser transmitter stations and the target point. A light receiving device at the target point is the key element in large-scale coordinate measurement systems. To ensure high-resolution and highly sensitive spatial coordinate measurement, a high-performance and miniaturized omnidirectional single-point photodetector (OSPD) is greatly desired. We report one design of OSPD using an aspheric lens, which achieves an enhanced reception angle of -5 deg to 45 deg in vertical and 360 deg in horizontal. As the heart of our OSPD, the aspheric lens is designed in a geometric model and optimized by LightTools Software, which enables the reflection of a wide-angle incident light beam into the single-point photodiode. The performance of home-made OSPD is characterized with working distances from 1 to 13 m and further analyzed utilizing developed a geometric model. The experimental and analytic results verify that our device is highly suitable for large-scale coordinate metrology. The developed device also holds great potential in various applications such as omnidirectional vision sensor, indoor global positioning system, and optical wireless communication systems.

Investigation of single lateral mode for 852nm diode lasers with ridge waveguide design

Science.gov (United States)

Liu, Chu; Guan, Baolu; Mi, Guoxin; Liao, Yiru; Liu, Zhenyang; Li, Jianjun; Xu, Chen

2016-11-01

852nm Narrow linewidth lasers can be widely used in the field of ultra-fine spectrum measurement, Cs atomic clock control, satellite and optical fiber communication and so on. Furthermore, the stability of the single lateral mode is a very important condition to guarantee the narrow linewidth lasers. Here we investigate experimentally the influence of the narrow ridge structure and asymmetrical waveguide design on the stability single lateral mode of an 852nm diode laser. According to the waveguide theoretical analysis, ridge mesa etch depth (Δη , related to the refractive index difference of parallel to the junction) and ridge mesa width (the narrower the more control force to low order mode) are the main elements for lateral modes. In this paper, we designed different structures to investigate and verify major factors for lateral mode by experiment, and to confirm our thought. Finally, the 5μm mesa ridge laser, 800nm etch depth, with groove structure obtains excellent steady single lateral mode output by 150mA operating current and 30°C temperature. The optical spectrum FWHM is 0.5nm and side mode suppression ratio is 27dBm with uncoated. The laser with 1mm cavity length showed the threshold current of 50mA, a lasing wavelength of λ = 852.6nm, slope efficiency of above 0.7mW/mA. We accomplished single lateral mode of ridge waveguide edge-emitting lasers which can also be used as a laser source in the ultra-narrow linewidth external cavity laser system.

Gestalt Theory in Visual Screen Design — A New Look at an old subject

OpenAIRE

Chang, D.; Dooley, L.; Tuovinen, J. E

2002-01-01

Although often presented as a single basis for educational visual screen design, Gestalt theory is not a single small set of visual principles uniformly applied by all designers. In fact, it appears that instructional visual design literature often deals with only a small set of Gestalt laws. In this project Gestalt literature was consulted to distil the most relevant Gestalt laws for educational visual screen design. Eleven laws were identified. They deal with balance/symmetry, continuation,...

Mechanical design optimization of a single-axis MOEMS accelerometer based on a grating interferometry cavity for ultrahigh sensitivity

Science.gov (United States)

Lu, Qianbo; Bai, Jian; Wang, Kaiwei; Lou, Shuqi; Jiao, Xufen; Han, Dandan; Yang, Guoguang

2016-08-01

The ultrahigh static displacement-acceleration sensitivity of a mechanical sensing chip is essential primarily for an ultrasensitive accelerometer. In this paper, an optimal design to implement to a single-axis MOEMS accelerometer consisting of a grating interferometry cavity and a micromachined sensing chip is presented. The micromachined sensing chip is composed of a proof mass along with its mechanical cantilever suspension and substrate. The dimensional parameters of the sensing chip, including the length, width, thickness and position of the cantilevers are evaluated and optimized both analytically and by finite-element-method (FEM) simulation to yield an unprecedented acceleration-displacement sensitivity. Compared with one of the most sensitive single-axis MOEMS accelerometers reported in the literature, the optimal mechanical design can yield a profound sensitivity improvement with an equal footprint area, specifically, 200% improvement in displacement-acceleration sensitivity with moderate resonant frequency and dynamic range. The modified design was microfabricated, packaged with the grating interferometry cavity and tested. The experimental results demonstrate that the MOEMS accelerometer with modified design can achieve the acceleration-displacement sensitivity of about 150μm/g and acceleration sensitivity of greater than 1500V/g, which validates the effectiveness of the optimal design.

Efficient experimental design of high-fidelity three-qubit quantum gates via genetic programming

Science.gov (United States)

Devra, Amit; Prabhu, Prithviraj; Singh, Harpreet; Arvind; Dorai, Kavita

2018-03-01

We have designed efficient quantum circuits for the three-qubit Toffoli (controlled-controlled-NOT) and the Fredkin (controlled-SWAP) gate, optimized via genetic programming methods. The gates thus obtained were experimentally implemented on a three-qubit NMR quantum information processor, with a high fidelity. Toffoli and Fredkin gates in conjunction with the single-qubit Hadamard gates form a universal gate set for quantum computing and are an essential component of several quantum algorithms. Genetic algorithms are stochastic search algorithms based on the logic of natural selection and biological genetics and have been widely used for quantum information processing applications. We devised a new selection mechanism within the genetic algorithm framework to select individuals from a population. We call this mechanism the "Luck-Choose" mechanism and were able to achieve faster convergence to a solution using this mechanism, as compared to existing selection mechanisms. The optimization was performed under the constraint that the experimentally implemented pulses are of short duration and can be implemented with high fidelity. We demonstrate the advantage of our pulse sequences by comparing our results with existing experimental schemes and other numerical optimization methods.

Structural Design of Two-Cylinder Single Overhead Camshaft

Science.gov (United States)

Zhao, Yuxia; Zhang, Kangsheng; Di, Jiejian

2018-01-01

Due to the higher performance demand, the camshaft is the key driving part in the engine. Because it is eccentric circular section part, it is very difficult to design and manufacture this kind of axial parts. Take two-cylinder single overhead camshaft for an example, the entire process of camshaft design is analyzed. The practice has proved that the method has simple, flexible and efficient advantages, and it can greatly shorten the design of artificial computing time.

Alzheimer Disease and Behavioral Variant Frontotemporal Dementia: Automatic Classification Based on Cortical Atrophy for Single-Subject Diagnosis.

Science.gov (United States)

Möller, Christiane; Pijnenburg, Yolande A L; van der Flier, Wiesje M; Versteeg, Adriaan; Tijms, Betty; de Munck, Jan C; Hafkemeijer, Anne; Rombouts, Serge A R B; van der Grond, Jeroen; van Swieten, John; Dopper, Elise; Scheltens, Philip; Barkhof, Frederik; Vrenken, Hugo; Wink, Alle Meije

2016-06-01

Purpose To investigate the diagnostic accuracy of an image-based classifier to distinguish between Alzheimer disease (AD) and behavioral variant frontotemporal dementia (bvFTD) in individual patients by using gray matter (GM) density maps computed from standard T1-weighted structural images obtained with multiple imagers and with independent training and prediction data. Materials and Methods The local institutional review board approved the study. Eighty-four patients with AD, 51 patients with bvFTD, and 94 control subjects were divided into independent training (n = 115) and prediction (n = 114) sets with identical diagnosis and imager type distributions. Training of a support vector machine (SVM) classifier used diagnostic status and GM density maps and produced voxelwise discrimination maps. Discriminant function analysis was used to estimate suitability of the extracted weights for single-subject classification in the prediction set. Receiver operating characteristic (ROC) curves and area under the ROC curve (AUC) were calculated for image-based classifiers and neuropsychological z scores. Results Training accuracy of the SVM was 85% for patients with AD versus control subjects, 72% for patients with bvFTD versus control subjects, and 79% for patients with AD versus patients with bvFTD (P ≤ .029). Single-subject diagnosis in the prediction set when using the discrimination maps yielded accuracies of 88% for patients with AD versus control subjects, 85% for patients with bvFTD versus control subjects, and 82% for patients with AD versus patients with bvFTD, with a good to excellent AUC (range, 0.81-0.95; P ≤ .001). Machine learning-based categorization of AD versus bvFTD based on GM density maps outperforms classification based on neuropsychological test results. Conclusion The SVM can be used in single-subject discrimination and can help the clinician arrive at a diagnosis. The SVM can be used to distinguish disease-specific GM patterns in patients with AD

Mild hallux valgus angle affects single-limb postural stability in asymptomatic subjects.

Science.gov (United States)

Çınar-Medeni, Özge; Atalay Guzel, Nevin; Basar, Selda

2016-01-01

Single-limb postural stability is a key component of lower extremity functional status. Factors affecting postural stability should be well defined to prevent injuries. The aim of this study was to investigate the effect of the hallux valgus angle on postural stability in asymptomatic subjects. A total of 19 subjects were included in the study. The hallux valgus angle and postural stability were assessed. Participants were assigned to two groups according to whether the hallux valgus angle was pathological or not. A hallux valgus angle greater than 15 degrees was accepted as pathological. The relationship between the hallux valgus angle and postural stability, and the differences in postural stability scores between the two groups were analyzed. Postural stability was assessed with a stabilometer. The test was performed with the eyes open. We found a significant correlation between the hallux valgus angle and mediolateral and overall stability index (r= 0.484, p= 0.036; r = 0.463, p= 0.046 respectively). Subjects with a pathological mild hallux valgus angle had greater stability index scores than normal subjects (phallux valgus angle has negative effects on postural stability as a forefoot deformity. This deformity should be taken into account for injury prevention strategies in pain-free younger adults.

Optimizing Nuclear Reaction Analysis (NRA) using Bayesian Experimental Design

International Nuclear Information System (INIS)

Toussaint, Udo von; Schwarz-Selinger, Thomas; Gori, Silvio

2008-01-01

Nuclear Reaction Analysis with 3 He holds the promise to measure Deuterium depth profiles up to large depths. However, the extraction of the depth profile from the measured data is an ill-posed inversion problem. Here we demonstrate how Bayesian Experimental Design can be used to optimize the number of measurements as well as the measurement energies to maximize the information gain. Comparison of the inversion properties of the optimized design with standard settings reveals huge possible gains. Application of the posterior sampling method allows to optimize the experimental settings interactively during the measurement process.

Design and Experimental Study of an Over-Under TBCC Exhaust System.

Science.gov (United States)

Mo, Jianwei; Xu, Jinglei; Zhang, Liuhuan

2014-01-01

Turbine-based combined-cycle (TBCC) propulsion systems have been a topic of research as a means for more efficient flight at supersonic and hypersonic speeds. The present study focuses on the fundamental physics of the complex flow in the TBCC exhaust system during the transition mode as the turbine exhaust is shut off and the ramjet exhaust is increased. A TBCC exhaust system was designed using methods of characteristics (MOC) and subjected to experimental and computational study. The main objectives of the study were: (1) to identify the interactions between the two exhaust jet streams during the transition mode phase and their effects on the whole flow-field structure; (2) to determine and verify the aerodynamic performance of the over-under TBCC exhaust nozzle; and (3) to validate the simulation ability of the computational fluid dynamics (CFD) software according to the experimental conditions. Static pressure taps and Schlieren apparatus were employed to obtain the wall pressure distributions and flow-field structures. Steady-state tests were performed with the ramjet nozzle cowl at six different positions at which the turbine flow path were half closed and fully opened, respectively. Methods of CFD were used to simulate the exhaust flow and they complemented the experimental study by providing greater insight into the details of the flow field and a means of verifying the experimental results. Results indicated that the flow structure was complicated because the two exhaust jet streams interacted with each other during the exhaust system mode transition. The exhaust system thrust coefficient varied from 0.9288 to 0.9657 during the process. The CFD simulation results agree well with the experimental data, which demonstrated that the CFD methods were effective in evaluating the aerodynamic performance of the TBCC exhaust system during the mode transition.

The Impact of Nocturnal Hypoglycemia on Sleep in Subjects With Type 2 Diabetes

DEFF Research Database (Denmark)

Jennum, Poul; Stender-Petersen, Kirstine; Rabøl, Rasmus

2015-01-01

night visits (one normoglycemic and one hypoglycemic) in randomized order. Plasma glucose (PG) levels were controlled by hyperinsulinemic glucose clamping. On the hypoglycemic night, hypoglycemia was induced after reaching sleep stage N2 by turning off glucose infusion until the PG target of 2......OBJECTIVE: The aim of this trial was to investigate the impact of nocturnal hypoglycemia on sleep patterns (assessed by polysomnography) and counterregulatory hormones. RESEARCH DESIGN AND METHODS: In this single-blinded, crossover trial, 26 subjects with type 2 diabetes attended two experimental.......7-2.8 mmol/L was reached and maintained for 15 min. Thereafter, subjects were brought back to normoglycemia for the rest of the night. On the normoglycemic night, PG was maintained at 5.0-7.0 mmol/L throughout the night. RESULTS: During the first 4 h of sleep (0-4 h; after reaching sleep stage N2...

Molten Core - Concrete interactions in nuclear accidents. Theory and design of an experimental facility

International Nuclear Information System (INIS)

Sevon, T.

2005-11-01

In a hypothetical severe accident in a nuclear power plant, the molten core of the reactor may flow onto the concrete floor of containment building. This would cause a molten core . concrete interaction (MCCI), in which the heat transfer from the hot melt to the concrete would cause melting of the concrete. In assessing the safety of nuclear reactors, it is important to know the consequences of such an interaction. As background to the subject, this publication includes a description of the core melt stabilization concept of the European Pressurized water Reactor (EPR), which is being built in Olkiluoto in Finland. The publication includes a description of the basic theory of the interaction and the process of spalling or cracking of concrete when it is heated rapidly. A literature survey and some calculations of the physical properties of concrete and corium. concrete mixtures at high temperatures have been conducted. In addition, an equation is derived for conservative calculation of the maximum possible concrete ablation depth. The publication also includes a literature survey of experimental research on the subject of the MCCI and discussion of the results and deficiencies of the experiments. The main result of this work is the general design of an experimental facility to examine the interaction of molten metals and concrete. The main objective of the experiments is to assess the probability of spalling, or cracking, of concrete under pouring of molten material. A program of five experiments has been designed, and pre-test calculations of the experiments have been conducted with MELCOR 1.8.5 accident analysis program and conservative analytic calculations. (orig.)

Visualizing Experimental Designs for Balanced ANOVA Models using Lisp-Stat

Directory of Open Access Journals (Sweden)

Philip W. Iversen

2004-12-01

Full Text Available The structure, or Hasse, diagram described by Taylor and Hilton (1981, American Statistician provides a visual display of the relationships between factors for balanced complete experimental designs. Using the Hasse diagram, rules exist for determining the appropriate linear model, ANOVA table, expected means squares, and F-tests in the case of balanced designs. This procedure has been implemented in Lisp-Stat using a software representation of the experimental design. The user can interact with the Hasse diagram to add, change, or delete factors and see the effect on the proposed analysis. The system has potential uses in teaching and consulting.

Bioinspiration: applying mechanical design to experimental biology.

Science.gov (United States)

Flammang, Brooke E; Porter, Marianne E

2011-07-01

The production of bioinspired and biomimetic constructs has fostered much collaboration between biologists and engineers, although the extent of biological accuracy employed in the designs produced has not always been a priority. Even the exact definitions of "bioinspired" and "biomimetic" differ among biologists, engineers, and industrial designers, leading to confusion regarding the level of integration and replication of biological principles and physiology. By any name, biologically-inspired mechanical constructs have become an increasingly important research tool in experimental biology, offering the opportunity to focus research by creating model organisms that can be easily manipulated to fill a desired parameter space of structural and functional repertoires. Innovative researchers with both biological and engineering backgrounds have found ways to use bioinspired models to explore the biomechanics of organisms from all kingdoms to answer a variety of different questions. Bringing together these biologists and engineers will hopefully result in an open discourse of techniques and fruitful collaborations for experimental and industrial endeavors.

Design considerations and experimental observations for the TAMU air-cooled reactor cavity cooling system for the VHTR

Energy Technology Data Exchange (ETDEWEB)

Sulaiman, S. A., E-mail: shamsulamri@tamu.edu; Dominguez-Ontiveros, E. E., E-mail: elvisdom@tamu.edu; Alhashimi, T., E-mail: jbudd123@tamu.edu; Budd, J. L., E-mail: dubaiboy@tamu.edu; Matos, M. D., E-mail: mailgoeshere@gmail.com; Hassan, Y. A., E-mail: yhasssan@tamu.edu [Department of Nuclear Engineering, Texas A and M University, College Station, TX, 77843-3133 (United States)

2015-04-29

The Reactor Cavity Cooling System (RCCS) is a promising passive decay heat removal system for the Very High Temperature Reactor (VHTR) to ensure reliability of the transfer of the core residual and decay heat to the environment under all off-normal circumstances. A small scale experimental test facility was constructed at Texas A and M University (TAMU) to study pertinent multifaceted thermal hydraulic phenomena in the air-cooled reactor cavity cooling system (RCCS) design based on the General Atomics (GA) concept for the Modular High Temperature Gas-Cooled Reactor (MHTGR). The TAMU Air-Cooled Experimental Test Facility is ⅛ scale from the proposed GA-MHTGR design. Groundwork for experimental investigations focusing into the complex turbulence mixing flow behavior inside the upper plenum is currently underway. The following paper illustrates some of the chief design considerations used in construction of the experimental test facility, complete with an outline of the planned instrumentation and data acquisition methods. Computational Fluid Dynamics (CFD) simulations were carried out to furnish some insights on the overall behavior of the air flow in the system. CFD simulations assisted the placement of the flow measurement sensors location. Preliminary experimental observations of experiments at 120oC inlet temperature suggested the presence of flow reversal for cases involving single active riser at both 5 m/s and 2.25 m/s, respectively and four active risers at 2.25 m/s. Flow reversal may lead to thermal stratification inside the upper plenum by means of steady state temperature measurements. A Particle Image Velocimetry (PIV) experiment was carried out to furnish some insight on flow patterns and directions.

Summary of the experimental multi-purpose very high temperature gas cooled reactor design

International Nuclear Information System (INIS)

1984-12-01

The report presents the design of Multi-purpose Very High Temperature Gas Cooled Reactor (the Experimental VHTR) based on the second stage of detailed design which was completed on March 1984, in the from of ''An application of reactor construction permit Appendix 8''. The Experimental VHTR is designed to satisfy with the design specification for the reactor thermal output 50 MW and reactor outlet temperature 950 0 C. The adequacy of the design is also checked by the safety analysis. The planning of plant system and safety is summarized such as safety design requirements and conformance with them, seismic design and plant arrangement. Concerning with the system of the Experimental VHTR the design basis, design data and components are described in the order. (author)

Design Issues and Inference in Experimental L2 Research

Science.gov (United States)

Hudson, Thom; Llosa, Lorena

2015-01-01

Explicit attention to research design issues is essential in experimental second language (L2) research. Too often, however, such careful attention is not paid. This article examines some of the issues surrounding experimental L2 research and its relationships to causal inferences. It discusses the place of research questions and hypotheses,…

Use of Experimental Design for Peuhl Cheese Process Optimization ...

African Journals Online (AJOL)

Use of Experimental Design for Peuhl Cheese Process Optimization. ... Journal of Applied Sciences and Environmental Management ... This work consisting in use of a central composite design enables the determination of optimal process conditions concerning: leaf extract volume added (7 mL), heating temperature ...

Experimentally supported control design for a direct drive robot

NARCIS (Netherlands)

Kostic, D.; Jager, de A.G.; Steinbuch, M.

2002-01-01

We promote the idea of an experimentally supported control design as a successful way to achieve accurate tracking of reference robot motions, under disturbance conditions and given the uncertainties arising from modeling errors. The Hinf robust control theory is used for design of motion

Safety and pharmacokinetics of single and multiple intravenous bolus doses of diclofenac sodium compared with oral diclofenac potassium 50 mg: A randomized, parallel-group, single-center study in healthy subjects.

Science.gov (United States)

Munjal, Sagar; Gautam, Anirudh; Okumu, Franklin; McDowell, James; Allenby, Kent

2016-01-01

In a randomized, parallel-group, single-center study in 42 healthy adults, the safety and pharmacokinetic parameters of an intravenous formulation of 18.75 and 37.5 mg diclofenac sodium (DFP-08) following single- and multiple-dose bolus administration were compared with diclofenac potassium 50 mg oral tablets. Mean AUC0-inf values for a 50-mg oral tablet and an 18.75-mg intravenous formulation were similar (1308.9 [393.0]) vs 1232.4 [147.6]). As measured by the AUC, DFP-08 18.75 mg and 37.5 mg demonstrated dose proportionality for extent of exposure. One subject in each of the placebo and DFP-08 18.75-mg groups and 2 subjects in the DFP-08 37.5-mg group reported adverse events that were considered by the investigator to be related to the study drug. All were mild in intensity and did not require treatment. Two subjects in the placebo group and 1 subject in the DFP-08 18.75-mg group reported grade 1 thrombophlebitis; no subjects reported higher than grade 1 thrombophlebitis after receiving a single intravenous dose. The 18.75- and 37.5-mg doses of intravenous diclofenac (single and multiple) were well tolerated for 7 days. Additional efficacy and safety studies are required to fully characterize the product. © 2015, The American College of Clinical Pharmacology.

Comparison of numerical results with experimental data for single-phase natural convection in an experimental sodium loop

International Nuclear Information System (INIS)

Ribando, R.J.

1979-01-01

A comparison is made between computed results and experimental data for a single-phase natural convection test in an experimental sodium loop. The test was conducted in the Thermal-Hydraulic Out-of-Reactor Safety (THORS) facility, an engineering-scale high temperature sodium loop at the Oak Ridge National Laboratory (ORNL) used for thermal-hydraulic testing of simulated Liquid Metal Fast Breeder Reactor (LMFBR) subassemblies at normal and off-normal operating conditions. Heat generation in the 19 pin assembly during the test was typical of decay heat levels. The test chosen for analysis in this paper was one of seven natural convection runs conducted in the facility using a variety of initial conditions and testing parameters. Specifically, in this test the bypass line was open to simulate a parallel heated assembly and the test was begun with a pump coastdown from a small initial forced flow. The computer program used to analyze the test, LONAC (LOw flow and NAtural Convection) is an ORNL-developed, fast-running, one-dimensional, single-phase, finite-difference model used for simulating forced and free convection transients in the THORS loop

Experimental quantum tossing of a single coin

International Nuclear Information System (INIS)

Nguyen, A T; Frison, J; Massar, S; Huy, K Phan

2008-01-01

The cryptographic protocol of coin tossing consists of two parties, Alice and Bob, who do not trust each other, but want to generate a random bit. If the parties use a classical communication channel and have unlimited computational resources, one of them can always cheat perfectly. If the parties use a quantum communication channel, there exist protocols such that neither party can cheat perfectly, although they may be able to significantly bias the coin. Here, we analyze in detail how the performance of a quantum coin tossing experiment should be compared to classical protocols, taking into account the inevitable experimental imperfections. We then report an all-optical fiber experiment in which a single coin is tossed whose randomness is higher than achievable by any classical protocol and present some easily realizable cheating strategies by Alice and Bob

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1984-03-01

A conceptual design study (option C) has been carried out for the fusion experimental reactor (FER). In addition to design of the tokamak reactor and associated systems based on the reference design specifications, feasibility of a water-shield reactor concept was examined as a topical study. The design study for the reference tokamak reactor has produced a reactor concept for the FER, along with major R D items for the concept, based on close examinations on thermal design, electromagnetics, neutronics and remote maintenance. Particular efforts have been directed to the area of electromagnetics. Detailed analyses with close simulation models have been performed on PF coil arrangements and configurations, shell effects of the blanket for plasma position unstability, feedback control, and eddy currents during disruptions. The major design specifications are as follows; Peak fusion power 437 MW Major radius 5.5 m Minor radius 1.1 m Plasma elongation 1.5 Plasma current 5.3 MA Toroidal beta 4 % Field on axis 5.7 T (author)

Conceptual design of Fusion Experimental Reactor (FER)

International Nuclear Information System (INIS)

Tone, T.; Fujisawa, N.

1983-01-01

Conceptual design studies of the Fusion Experimental Reactor (FER) have been performed. The FER has an objective of achieving selfignition and demonstrating engineering feasibility as a next generation tokamak to JT-60. Various concepts of the FER have been considered. The reference design is based on a double-null divertor. Optional design studies with some attractive features based on advanced concepts such as pumped limiter and RF current drive have been carried out. Key design parameters are; fusion power of 440 MW, average neutron wall loading of 1MW/m 2 , major radius of 5.5m, plasma minor radius of 1.1m, plasma elongation of 1.5, plasma current of 5.3MA, toroidal beta of 4%, toroidal field on plasma axis of 5.7T and tritium breeding ratio of above unity

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .1. DESIGN CONSTRUCTION AND THEORETICAL EVALUATION

NARCIS (Netherlands)

DUINEVELD, CAA; SMILDE, AK; DOORNBOS, DA

The combination of process variables and mixture variables in experimental design is a problem which has not yet been solved. It is examined here whether a set of designs can be found which can be used for a series of models of reasonable complexity. The proposed designs are compared with known

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .1. DESIGN CONSTRUCTION AND THEORETICAL EVALUATION

NARCIS (Netherlands)

DUINEVELD, C. A. A.; Smilde, A. K.; Doornbos, D. A.

1993-01-01

The combination of process variables and mixture variables in experimental design is a problem which has not yet been solved. It is examined here whether a set of designs can be found which can be used for a series of models of reasonable complexity. The proposed designs are compared with known

Design optimization of shell-and-tube heat exchangers using single objective and multiobjective particle swarm optimization

International Nuclear Information System (INIS)

Elsays, Mostafa A.; Naguib Aly, M; Badawi, Alya A.

2010-01-01

The Particle Swarm Optimization (PSO) algorithm is used to optimize the design of shell-and-tube heat exchangers and determine the optimal feasible solutions so as to eliminate trial-and-error during the design process. The design formulation takes into account the area and the total annual cost of heat exchangers as two objective functions together with operating as well as geometrical constraints. The Nonlinear Constrained Single Objective Particle Swarm Optimization (NCSOPSO) algorithm is used to minimize and find the optimal feasible solution for each of the nonlinear constrained objective functions alone, respectively. Then, a novel Nonlinear Constrained Mult-objective Particle Swarm Optimization (NCMOPSO) algorithm is used to minimize and find the Pareto optimal solutions for both of the nonlinear constrained objective functions together. The experimental results show that the two algorithms are very efficient, fast and can find the accurate optimal feasible solutions of the shell and tube heat exchangers design optimization problem. (orig.)

An Experimental Verification of morphology of ibuprofen crystals from CAMD designed solvent

DEFF Research Database (Denmark)

Karunanithi, Arunprakash T.; Acquah, Charles; Achenie, Luke E.K.

2007-01-01

of crystals formed from solvents, necessitates additional experimental verification steps. In this work we report the experimental verification of crystal morphology for the case study, solvent design for ibuprofen crystallization, presented in Karunanithi et al. [2006. A computer-aided molecular design...

Design and experimental characterization of an EM pump

International Nuclear Information System (INIS)

Kim, Hee Reyoung; Hong, Sang Hee

1999-01-01

Generally, an EM (electromagnetic) pump is been employed to circulate electrically conducting liquids by using the Lorentz force. Especially, at the liquid metal reactor (LMR), which uses liquid sodium with high electrical conductivity as a coolant, an EM pump is needed due to its advantages over a mechanical pump, such as no rotating parts, no noise, and simplicity. In this research, an EM pump of a pilot annular linear induction type with a flow rate of 200 l/min was designed by using the electrical equivalent-circuit method. The pump was designed and manufactured by considering material and environmental (high temperature and liquid sodium) requirements. The pump performance was experimentally characterized based on input currents, voltage, power, and frequency. Also, the theoretical prediction was compared with the experimental result

Decoding subjective mental states from fMRI activity patterns

International Nuclear Information System (INIS)

Tamaki, Masako; Kamitani, Yukiyasu

2011-01-01

In recent years, functional magnetic resonance imaging (fMRI) decoding has emerged as a powerful tool to read out detailed stimulus features from multi-voxel brain activity patterns. Moreover, the method has been extended to perform a primitive form of 'mind-reading,' by applying a decoder 'objectively' trained using stimulus features to more 'subjective' conditions. In this paper, we first introduce basic procedures for fMRI decoding based on machine learning techniques. Second, we discuss the source of information used for decoding, in particular, the possibility of extracting information from subvoxel neural structures. We next introduce two experimental designs for decoding subjective mental states: the 'objective-to-subjective design' and the 'subjective-to-subjective design.' Then, we illustrate recent studies on the decoding of a variety of mental states, such as, attention, awareness, decision making, memory, and mental imagery. Finally, we discuss the challenges and new directions of fMRI decoding. (author)

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1984-02-01

This report describes the engineering conceptual design of Fusion Experimental Reactor (FER) which is to be built as a next generation tokamak machine. This design covers overall reactor systems including MHD equilibrium analysis, mechanical configuration of reactor, divertor, pumped limiter, first wall/breeding blanket/shield, toroidal field magnet, poloidal field magnet, cryostat, electromagnetic analysis, vacuum system, power handling and conversion, NBI, RF heating device, tritium system, neutronics, maintenance, cooling system and layout of facilities. The engineering comparison of a divertor with pumped limiters and safety analysis of reactor systems are also conducted. (author)

Fast Bayesian optimal experimental design and its applications

KAUST Repository

Long, Quan

2015-01-01

We summarize our Laplace method and multilevel method of accelerating the computation of the expected information gain in a Bayesian Optimal Experimental Design (OED). Laplace method is a widely-used method to approximate an integration

Experimental Investigation on Adaptive Robust Controller Designs Applied to Constrained Manipulators

Directory of Open Access Journals (Sweden)

Marco H. Terra

2013-04-01

Full Text Available In this paper, two interlaced studies are presented. The first is directed to the design and construction of a dynamic 3D force/moment sensor. The device is applied to provide a feedback signal of forces and moments exerted by the robotic end-effector. This development has become an alternative solution to the existing multi-axis load cell based on static force and moment sensors. The second one shows an experimental investigation on the performance of four different adaptive nonlinear H∞ control methods applied to a constrained manipulator subject to uncertainties in the model and external disturbances. Coordinated position and force control is evaluated. Adaptive procedures are based on neural networks and fuzzy systems applied in two different modeling strategies. The first modeling strategy requires a well-known nominal model for the robot, so that the intelligent systems are applied only to estimate the effects of uncertainties, unmodeled dynamics and external disturbances. The second strategy considers that the robot model is completely unknown and, therefore, intelligent systems are used to estimate these dynamics. A comparative study is conducted based on experimental implementations performed with an actual planar manipulator and with the dynamic force sensor developed for this purpose.

Experimental research of the yielding behavior of a graphite cylinder subjected to line loading

International Nuclear Information System (INIS)

Liu Hetong; Ma Qinwei; Ma Shaopeng; Wang Hongtao

2014-01-01

The graphite material cylinders are widely used in High-temperature gas-cooled reactor as connecting components. For engineering design, the deformation behavior, especially the yielding process of the graphite cylinder should be investigated in order to evaluate the carrying capacity of the cylinder. The yielding formation and propagation of a graphite cylinder subjected to line loading, which corresponds to the global behavior of the structure, was experimentally studied and evaluated by measuring the strain fields on the end of the cylinder using Digital Image Correlation. The global behavior of the structure is expressed by a relationship between the average stress (load divided by contact area) and the equivalent strain (ratio of half width of contact area to radius of the cylinder), the contact area was measured by identifying the color area of the pressure film in a new experiment which graphite component is loaded and unloaded continuously. A correspondence between the yielding state and the nonlinearity of the global behavior was constructed, as loading was increased, the cylinder was found to first yield at a specific point after which a yielding core formed and propagated. Before the yielding core propagated to the surface of the cylinder, the global behavior of the structure remained linear. After the yielding core propagated to the surface of the cylinder, the global behavior became nonlinear. The correspondence constructed in the paper will be helpful to understand the failure process and to evaluate the carrying capacity of a graphite cylinder subjected to line loading in reactors. (author)

Security evaluation and design of structures subjected to blast loading

OpenAIRE

Pereira, João Miguel

2014-01-01

Tese de doutoramento em Engenharia Civil The work presented in this thesis was developed at the Department of Civil Engineering of University of Minho. This work involves experimental and numerical campaigns and intends to give a contribution for a better understanding of the effect of explosions. Blast loading is a subject of much actuality and considerable lack of expertise. Europe has never been so rich and safe, where the violent years of the first half of the 20th centu...

Optimal Experimental Design of Furan Shock Tube Kinetic Experiments

KAUST Repository

Kim, Daesang

2015-01-07

A Bayesian optimal experimental design methodology has been developed and applied to refine the rate coefficients of elementary reactions in Furan combustion. Furans are considered as potential renewable fuels. We focus on the Arrhenius rates of Furan + OH ↔ Furyl-2 + H2O and Furan ↔ OH Furyl-3 + H2O, and rely on the OH consumption rate as experimental observable. A polynomial chaos surrogate is first constructed using an adaptive pseudo-spectral projection algorithm. The PC surrogate is then exploited in conjunction with a fast estimation of the expected information gain in order to determine the optimal design in the space of initial temperatures and OH concentrations.

Experimental design and quantitative analysis of microbial community multiomics.

Science.gov (United States)

Mallick, Himel; Ma, Siyuan; Franzosa, Eric A; Vatanen, Tommi; Morgan, Xochitl C; Huttenhower, Curtis

2017-11-30

Studies of the microbiome have become increasingly sophisticated, and multiple sequence-based, molecular methods as well as culture-based methods exist for population-scale microbiome profiles. To link the resulting host and microbial data types to human health, several experimental design considerations, data analysis challenges, and statistical epidemiological approaches must be addressed. Here, we survey current best practices for experimental design in microbiome molecular epidemiology, including technologies for generating, analyzing, and integrating microbiome multiomics data. We highlight studies that have identified molecular bioactives that influence human health, and we suggest steps for scaling translational microbiome research to high-throughput target discovery across large populations.

Design of broadband single polarized antenna

Science.gov (United States)

Shin, Phoo Kho; Aziz, Mohamad Zoinol Abidin Abd.; Ahmad, Badrul Hisham; Ramli, Mohamad Hafize Bin; Fauzi, Noor Azamiah Md; Malek, Mohd Fareq Abd

2015-05-01

In practical wireless communication application, bandwidth enhancement becomes one of the major design considerations. At the same time, circular polarized (CP) antenna received much attention for the applications of modern wireless communication system when compared to linear polarized (LP) antenna. This is because CP antenna can reduce the multipath effect. Hence, broadband antenna with operating frequency at 2.4GHz for WLAN application is proposed. The proposed antenna is done by using L-probe amendment with rectangular patch. The rectangular patch and copper ground plane is separated with 10mm air gap. This approach is used to enhance the bandwidth and the gain of the proposed antenna. The bandwidth of the designed antenna is more than 200MHz which meet broadband application. The return loss for the antenna is below -10dB to achieved 90% matching efficiency. The position of L-probe feed is altered in order to obtained different polarizations. The broadband antenna had been designed and simulated by using Computer Simulation Technology (CST) software. In this paper, the comparison for single polarized antenna with the design of non-inverted patch and inverted patch is discussed. The characteristics of the S-parameter, axial ratio, gain, surface current for each designed antenna are analyzed.

EFFECTIVENESS OF MUSCLE STRETCHING IN OCCUPATION RELATED CHRONIC MECHANICAL LOW BACK PAIN IN COMMUNITY NURSES –A SINGLE BLIND STUDY

OpenAIRE

Khwairakpam Zhimina Devi; Sai Kumar. N; Vinod Babu. K; V.R. Ayyappan

2014-01-01

Background and Objective: Stretching of Lower Back Muscle, Hamstring and Tensor Fasciae Latae have an immediate effect on Chronic Lower Back Pain. Hence the purpose is to find the short term effect of stretching of Lower Back Muscle, Hamstring and Tensor Fasciae Latae on intensity of low back pain, flexibility and functional disability in occupation related Chronic Mechanical Low Back Pain in Community Nurses. Method: Single blind experimental study design, 40 subjects with Chronic mechani...

AHSG tag single nucleotide polymorphisms associate with type 2 diabetes and dyslipidemia: studies of metabolic traits in 7,683 white Danish subjects

DEFF Research Database (Denmark)

Andersen, Gitte; Burgdorf, Kristoffer Sølvsten; Sparsø, Thomas

2008-01-01

been largely successful. We related seven frequent AHSG tag single nucleotide polymorphisms to a range of metabolic traits, including type 2 diabetes, obesity, and dyslipidemia. RESEARCH DESIGN AND METHODS: The polymorphisms were genotyped in 7,683 white Danish subjects using Taqman allelic...... with dyslipidemia (P = 0.003 and P(corr) = 0.009). Thr248Met (rs4917) tended to associate with lower fasting and post-oral glucose tolerance test serum insulin release (P = 0.02, P(corr) = 0.1 for fasting and P = 0.04, P(corr) = 0.2 for area under the insulin curve) and improved insulin sensitivity estimated...

Mechanism Design for Single Leader Stackelberg Problems and Application to Procurement Auction Design

OpenAIRE

Garg, Dinesh; Narahari, Y

2008-01-01

In this paper, we focus on mechanism design for single leader Stackelberg problems, which are a special case of hierarchical decision making problems in which a distinguished agent, known as the leader, makes the first move and this action is followed by the actions of the remaining agents, which are known as the followers. These problems are also known as single leader rest follower (SLRF) problems. There are many examples of such problems in the areas of electronic commerce, supply chain ma...

Experimental investigations on solar heating/heat pump systems for single family houses

DEFF Research Database (Denmark)

Andersen, Elsa; Perers, Bengt

In the period 2013-2017 the project “Experimental investigations on solar heat pump systems for single family houses” is carried out at Department of Civil Engineering, Technical University of Denmark. The aim of this project is to increase the knowledge of the heat and mass transfer in the combi...

Spatial Memory in the Progeny of Rats Subjected to Different Types of Experimental Preeclampsia.

Science.gov (United States)

Perfilova, V N; Zhakupova, G A; Lashchenova, L I; Lebedeva, S A; Tyurenkov, I N

2016-09-01

Spatial memory was studied in 2-month-old offspring of rats subjected to different types of experimental preeclampsia (replacement of drinking water with 1.8% NaCl from day 1 to 21 of gestation or intraperitoneal administration of non-selective NO-synthase inhibitor L-NAME to pregnant rats in a daily dose of 25 mg/kg for 7 days on gestation days 14-20). Spatial memory was evaluated in an elevated 8-arm radial maze. Both types of experimental preeclampsia impaired spatial (long-term and short-term) memory and can be used in the development of drugs correcting negative effects of this pregnancy complication on memory.

Intuitive web-based experimental design for high-throughput biomedical data.

Science.gov (United States)

Friedrich, Andreas; Kenar, Erhan; Kohlbacher, Oliver; Nahnsen, Sven

2015-01-01

Big data bioinformatics aims at drawing biological conclusions from huge and complex biological datasets. Added value from the analysis of big data, however, is only possible if the data is accompanied by accurate metadata annotation. Particularly in high-throughput experiments intelligent approaches are needed to keep track of the experimental design, including the conditions that are studied as well as information that might be interesting for failure analysis or further experiments in the future. In addition to the management of this information, means for an integrated design and interfaces for structured data annotation are urgently needed by researchers. Here, we propose a factor-based experimental design approach that enables scientists to easily create large-scale experiments with the help of a web-based system. We present a novel implementation of a web-based interface allowing the collection of arbitrary metadata. To exchange and edit information we provide a spreadsheet-based, humanly readable format. Subsequently, sample sheets with identifiers and metainformation for data generation facilities can be created. Data files created after measurement of the samples can be uploaded to a datastore, where they are automatically linked to the previously created experimental design model.

The effects of single instance, multiple instance, and general case training on generalized vending machine use by moderately and severely handicapped students.

OpenAIRE

Sprague, J R; Horner, R H

1984-01-01

This report provides an experimental analysis of generalized vending machine use by six moderately or severely retarded high school students. Dependent variables were training trials to criterion and performance on 10 nontrained "generalization" vending machines. A multiple-baseline design across subjects was used to compare three strategies for teaching generalized vending machine use. Training occurred with (a) a single vending machine, (b) three similar machines, or (c) three machines that...

An Evaluation of a Computer-Based Training on the Visual Analysis of Single-Subject Data

Science.gov (United States)

Snyder, Katie

2013-01-01

Visual analysis is the primary method of analyzing data in single-subject methodology, which is the predominant research method used in the fields of applied behavior analysis and special education. Previous research on the reliability of visual analysis suggests that judges often disagree about what constitutes an intervention effect. Considering…

Experimental burn plot trial in the Kruger National Park: history, experimental design and suggestions for data analysis

Directory of Open Access Journals (Sweden)

R. Biggs

2003-12-01

Full Text Available The experimental burn plot (EBP trial initiated in 1954 is one of few ongoing long-termfire ecology research projects in Africa. The trial aims to assess the impacts of differentfire regimes in the Kruger National Park. Recent studies on the EBPs have raised questions as to the experimental design of the trial, and the appropriate model specificationwhen analysing data. Archival documentation reveals that the original design was modified on several occasions, related to changes in the park's fire policy. These modifications include the addition of extra plots, subdivision of plots and changes in treatmentsover time, and have resulted in a design which is only partially randomised. The representativity of the trial plots has been questioned on account of their relatively small size,the concentration of herbivores on especially the frequently burnt plots, and soil variation between plots. It is suggested that these factors be included as covariates inexplanatory models or that certain plots be excluded from data analysis based on resultsof independent studies of these factors. Suggestions are provided for the specificationof the experimental design when analysing data using Analysis of Variance. It is concluded that there is no practical alternative to treating the trial as a fully randomisedcomplete block design.

Experimental research of inclined-micro-fin flat tube on single phase convection heat transfer

International Nuclear Information System (INIS)

Fan Guangming; Sun Zhongning; Wang Meng

2011-01-01

The experimental research of heat transfer and flow resistance characteristics of single phase water in four inclined-micro-fin flat tubes with different physical dimensions was conducted. At the same time,suitable criteria were selected to evaluate the efficiency of inclined-micro-fin flat tubes within the experimental scope and the optimal working region was determined. The results indicate that inclined-micro-fin flat tubes can greatly enhance the single-phase heat transfer in turbulent flow and the maximum heat transfer coefficient attains to 5.9 times of that in smooth tube. The quantities of heat transfer for inclined-micro-fin flat tubes are three times higher than that of smooth tube with the same of heat exchange area and pump power. (authors)

Optimal Experimental Design for Large-Scale Bayesian Inverse Problems

KAUST Repository

Ghattas, Omar

2014-01-06

We develop a Bayesian framework for the optimal experimental design of the shock tube experiments which are being carried out at the KAUST Clean Combustion Research Center. The unknown parameters are the pre-exponential parameters and the activation energies in the reaction rate expressions. The control parameters are the initial mixture composition and the temperature. The approach is based on first building a polynomial based surrogate model for the observables relevant to the shock tube experiments. Based on these surrogates, a novel MAP based approach is used to estimate the expected information gain in the proposed experiments, and to select the best experimental set-ups yielding the optimal expected information gains. The validity of the approach is tested using synthetic data generated by sampling the PC surrogate. We finally outline a methodology for validation using actual laboratory experiments, and extending experimental design methodology to the cases where the control parameters are noisy.

Experimental test of the strongly nonclassical character of a noisy squeezed single-photon state

DEFF Research Database (Denmark)

Jezek, M.; Tipsmark, A.; Dong, R.

2012-01-01

We experimentally verify the quantum non-Gaussian character of a conditionally generated noisy squeezed single-photon state with a positive Wigner function. Employing an optimized witness based on probabilities of squeezed vacuum and squeezed single-photon states, we prove that the state cannot...... be expressed as a mixture of Gaussian states. In our experiment, the non-Gaussian state is generated by conditional subtraction of a single photon from a squeezed vacuum state. The state is probed with a homodyne detector and the witness is determined by averaging a suitable pattern function over the measured...

Experimental Evidence for Quantum Interference and Vibrationally Induced Decoherence in Single-Molecule Junctions

Science.gov (United States)

Ballmann, Stefan; Härtle, Rainer; Coto, Pedro B.; Elbing, Mark; Mayor, Marcel; Bryce, Martin R.; Thoss, Michael; Weber, Heiko B.

2012-08-01

We analyze quantum interference and decoherence effects in single-molecule junctions both experimentally and theoretically by means of the mechanically controlled break junction technique and density-functional theory. We consider the case where interference is provided by overlapping quasidegenerate states. Decoherence mechanisms arising from electronic-vibrational coupling strongly affect the electrical current flowing through a single-molecule contact and can be controlled by temperature variation. Our findings underline the universal relevance of vibrations for understanding charge transport through molecular junctions.

Inelastic response of piping systems subjected to in-structure seismic excitation

International Nuclear Information System (INIS)

Campbell, R.D.; Kennedy, R.P.; Trasher, R.D.

1983-01-01

A study was undertaken to examine the inelastic response of single-degree-of-freedom systems and a simple piping system to varying levels of earthquake loading with superimposed static loading. The objective was to examine the conservatism inherent in ASME code rules for the design of piping systems by quantifying the ratio of the dynamic margin to the static margin for various degrees of inelastic strain, system frequencies and instructure time histories. Previous studies of elastic, perfectly-plastic and bilinear strain-hardening, single-degree-of-freedom models subjected to earthquake ground motion records have demonstrated the conservatism in current design methodology and design codes for earthquake resistant design of structures. This study compares response of single degree of freedom and simple piping system subjected to typical in-structure earthquake time histories and focuses on the excess margin inherent in current design criteria for piping systems. It is shown that the factor of safety against failure is variable and is dependent upon the frequency content of the loading, the dynamic characteristics of the piping system and the allowable system ductility. A recommendation is made for revision to current criteria on the basis of maintaining a constant factor of safety for dynamic and static loading

A Field-Tested Task Analysis for Creating Single-Subject Graphs Using Microsoft[R] Office Excel

Science.gov (United States)

Lo, Ya-yu; Konrad, Moira

2007-01-01

Creating single-subject (SS) graphs is challenging for many researchers and practitioners because it is a complex task with many steps. Although several authors have introduced guidelines for creating SS graphs, many users continue to experience frustration. The purpose of this article is to minimize these frustrations by providing a field-tested…

Single-Mode VCSELs

Science.gov (United States)

Larsson, Anders; Gustavsson, Johan S.

The only active transverse mode in a truly single-mode VCSEL is the fundamental mode with a near Gaussian field distribution. A single-mode VCSEL produces a light beam of higher spectral purity, higher degree of coherence and lower divergence than a multimode VCSEL and the beam can be more precisely shaped and focused to a smaller spot. Such beam properties are required in many applications. In this chapter, after discussing applications of single-mode VCSELs, we introduce the basics of fields and modes in VCSELs and review designs implemented for single-mode emission from VCSELs in different materials and at different wavelengths. This includes VCSELs that are inherently single-mode as well as inherently multimode VCSELs where higher-order modes are suppressed by mode selective gain or loss. In each case we present the current state-of-the-art and discuss pros and cons. At the end, a specific example with experimental results is provided and, as a summary, the most promising designs based on current technologies are identified.

Statistical experimental design for saltstone mixtures

International Nuclear Information System (INIS)

Harris, S.P.; Postles, R.L.

1992-01-01

The authors used a mixture experimental design for determining a window of operability for a process at the U.S. Department of Energy, Savannah River Site, Defense Waste Processing Facility (DWPF). The high-level radioactive waste at the Savannah River Site is stored in large underground carbon steel tanks. The waste consists of a supernate layer and a sludge layer. Cesium-137 will be removed from the supernate by precipitation and filtration. After further processing, the supernate layer will be fixed as a grout for disposal in concrete vaults. The remaining precipitate will be processed at the DWPF with treated waste tank sludge and glass-making chemicals into borosilicate glass. The leach-rate properties of the supernate grout formed from various mixes of solidified coefficients for NO 3 and chromium were used as a measure of leach rate. Various mixes of cement, Ca(OH) 2 , salt, slag, and fly ash were used. These constituents comprise the whole mix. Thus, a mixture experimental design was used. The regression procedure (PROC REG) in SAS was used to produce analysis of variance (ANOVA) statistics. In addition, detailed model diagnostics are readily available for identifying suspicious observations. For convenience, trillinear contour (TLC) plots, a standard graphics tool for examining mixture response surfaces, of the fitted model were produced using ECHIP

MUP, CEC-DES, STRADE. Codes for uncertainty propagation, experimental design and stratified random sampling techniques

International Nuclear Information System (INIS)

Amendola, A.; Astolfi, M.; Lisanti, B.

1983-01-01

The report describes the how-to-use of the codes: MUP (Monte Carlo Uncertainty Propagation) for uncertainty analysis by Monte Carlo simulation, including correlation analysis, extreme value identification and study of selected ranges of the variable space; CEC-DES (Central Composite Design) for building experimental matrices according to the requirements of Central Composite and Factorial Experimental Designs; and, STRADE (Stratified Random Design) for experimental designs based on the Latin Hypercube Sampling Techniques. Application fields, of the codes are probabilistic risk assessment, experimental design, sensitivity analysis and system identification problems

Microarray expression profiling of human dental pulp from single subject.

Science.gov (United States)

Tete, Stefano; Mastrangelo, Filiberto; Scioletti, Anna Paola; Tranasi, Michelangelo; Raicu, Florina; Paolantonio, Michele; Stuppia, Liborio; Vinci, Raffaele; Gherlone, Enrico; Ciampoli, Cristian; Sberna, Maria Teresa; Conti, Pio

2008-01-01

Microarray is a recently developed simultaneous analysis of expression patterns of thousand of genes. The aim of this research was to evaluate the expression profile of human healthy dental pulp in order to find the presence of genes activated and encoding for proteins involved in the physiological process of human dental pulp. We report data obtained by analyzing expression profiles of human tooth pulp from single subjects, using an approach based on the amplification of the total RNA. Experiments were performed on a high-density array able to analyse about 21,000 oligonucleotide sequences of about 70 bases in duplicate, using an approach based on the amplification of the total RNA from the pulp of a single tooth. Obtained data were analyzed using the S.A.M. system (Significance Analysis of Microarray) and genes were merged according to their molecular functions and biological process by the Onto-Express software. The microarray analysis revealed 362 genes with specific pulp expression. Genes showing significant high expression were classified in genes involved in tooth development, protoncogenes, genes of collagen, DNAse, Metallopeptidases and Growth factors. We report a microarray analysis, carried out by extraction of total RNA from specimens of healthy human dental pulp tissue. This approach represents a powerful tool in the study of human normal and pathological pulp, allowing minimization of the genetic variability due to the pooling of samples from different individuals.

Comparison of numerical results with experimental data for single-phase natural convection in an experimental sodium loop. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Ribando, R.J.

1979-01-01

A comparison is made between computed results and experimental data for a single-phase natural convection test in an experimental sodium loop. The test was conducted in the Thermal-Hydraulic Out-of-Reactor Safety (THORS) facility, an engineering-scale high temperature sodium loop at the Oak Ridge National Laboratory (ORNL) used for thermal-hydraulic testing of simulated Liquid Metal Fast Breeder Reactor (LMFBR) subassemblies at normal and off-normal operating conditions. Heat generation in the 19 pin assembly during the test was typical of decay heat levels. The test chosen for analysis in this paper was one of seven natural convection runs conducted in the facility using a variety of initial conditions and testing parameters. Specifically, in this test the bypass line was open to simulate a parallel heated assembly and the test was begun with a pump coastdown from a small initial forced flow. The computer program used to analyze the test, LONAC (LOw flow and NAtural Convection) is an ORNL-developed, fast-running, one-dimensional, single-phase, finite-difference model used for simulating forced and free convection transients in the THORS loop.

Trajectory Design for a Single-String Impactor Concept

Science.gov (United States)

Dono Perez, Andres; Burton, Roland; Stupl, Jan; Mauro, David

2017-01-01

This paper introduces a trajectory design for a secondary spacecraft concept to augment science return in interplanetary missions. The concept consist of a single-string probe with a kinetic impactor on board that generates an artificial plume to perform in-situ sampling. The trajectory design was applied to a particular case study that samples ejecta particles from the Jovian moon Europa. Results were validated using statistical analysis. Details regarding the navigation, targeting and disposal challenges related to this concept are presented herein.

Differentiated Bayesian Conjoint Choice Designs

NARCIS (Netherlands)

Z. Sándor (Zsolt); M. Wedel (Michel)

2003-01-01

textabstractPrevious conjoint choice design construction procedures have produced a single design that is administered to all subjects. This paper proposes to construct a limited set of different designs. The designs are constructed in a Bayesian fashion, taking into account prior uncertainty about

Experimental Design: Utilizing Microsoft Mathematics in Teaching and Learning Calculus

Science.gov (United States)

Oktaviyanthi, Rina; Supriani, Yani

2015-01-01

The experimental design was conducted to investigate the use of Microsoft Mathematics, free software made by Microsoft Corporation, in teaching and learning Calculus. This paper reports results from experimental study details on implementation of Microsoft Mathematics in Calculus, students' achievement and the effects of the use of Microsoft…

Set membership experimental design for biological systems

Directory of Open Access Journals (Sweden)

Marvel Skylar W

2012-03-01

Full Text Available Abstract Background Experimental design approaches for biological systems are needed to help conserve the limited resources that are allocated for performing experiments. The assumptions used when assigning probability density functions to characterize uncertainty in biological systems are unwarranted when only a small number of measurements can be obtained. In these situations, the uncertainty in biological systems is more appropriately characterized in a bounded-error context. Additionally, effort must be made to improve the connection between modelers and experimentalists by relating design metrics to biologically relevant information. Bounded-error experimental design approaches that can assess the impact of additional measurements on model uncertainty are needed to identify the most appropriate balance between the collection of data and the availability of resources. Results In this work we develop a bounded-error experimental design framework for nonlinear continuous-time systems when few data measurements are available. This approach leverages many of the recent advances in bounded-error parameter and state estimation methods that use interval analysis to generate parameter sets and state bounds consistent with uncertain data measurements. We devise a novel approach using set-based uncertainty propagation to estimate measurement ranges at candidate time points. We then use these estimated measurements at the candidate time points to evaluate which candidate measurements furthest reduce model uncertainty. A method for quickly combining multiple candidate time points is presented and allows for determining the effect of adding multiple measurements. Biologically relevant metrics are developed and used to predict when new data measurements should be acquired, which system components should be measured and how many additional measurements should be obtained. Conclusions The practicability of our approach is illustrated with a case study. This

Experimental demonstration of quantum contextuality on an NMR qutrit

Energy Technology Data Exchange (ETDEWEB)

Dogra, Shruti; Dorai, Kavita, E-mail: kavita@iisermohali.ac.in; Arvind

2016-05-20

We experimentally test quantum contextuality of a single qutrit using NMR. The contextuality inequalities based on nine observables developed by Kurzynski et al. are first reformulated in terms of traceless observables which can be measured in an NMR experiment. These inequalities reveal the contextuality of almost all single-qutrit states. We demonstrate the violation of the inequality on four different initial states of a spin-1 deuterium nucleus oriented in a liquid crystal matrix, and follow the violation as the states evolve in time. We also describe and experimentally perform a single-shot test of contextuality for a subclass of qutrit states whose density matrix is diagonal in the energy basis. - Highlights: • A contextuality inequality for a single qutrit was designed using traceless observables. • The violation of the inequality was experimentally demonstrated using NMR. • A single-shot test was experimentally performed for a subclass of diagonal qutrit states.

Experimental demonstration of quantum contextuality on an NMR qutrit

International Nuclear Information System (INIS)

Dogra, Shruti; Dorai, Kavita; Arvind

2016-01-01

We experimentally test quantum contextuality of a single qutrit using NMR. The contextuality inequalities based on nine observables developed by Kurzynski et al. are first reformulated in terms of traceless observables which can be measured in an NMR experiment. These inequalities reveal the contextuality of almost all single-qutrit states. We demonstrate the violation of the inequality on four different initial states of a spin-1 deuterium nucleus oriented in a liquid crystal matrix, and follow the violation as the states evolve in time. We also describe and experimentally perform a single-shot test of contextuality for a subclass of qutrit states whose density matrix is diagonal in the energy basis. - Highlights: • A contextuality inequality for a single qutrit was designed using traceless observables. • The violation of the inequality was experimentally demonstrated using NMR. • A single-shot test was experimentally performed for a subclass of diagonal qutrit states.

Simulation and Experimental Characterization of Microscopically Accessible Hydrodynamic Microvortices

Directory of Open Access Journals (Sweden)

Deirdre R. Meldrum

2012-06-01

Full Text Available Single-cell studies of phenotypic heterogeneity reveal more information about pathogenic processes than conventional bulk-cell analysis methods. By enabling high-resolution structural and functional imaging, a single-cell three-dimensional (3D imaging system can be used to study basic biological processes and to diagnose diseases such as cancer at an early stage. One mechanism that such systems apply to accomplish 3D imaging is rotation of a single cell about a fixed axis. However, many cell rotation mechanisms require intricate and tedious microfabrication, or fail to provide a suitable environment for living cells. To address these and related challenges, we applied numerical simulation methods to design new microfluidic chambers capable of generating fluidic microvortices to rotate suspended cells. We then compared several microfluidic chip designs experimentally in terms of: (1 their ability to rotate biological cells in a stable and precise manner; and (2 their suitability, from a geometric standpoint, for microscopic cell imaging. We selected a design that incorporates a trapezoidal side chamber connected to a main flow channel because it provided well-controlled circulation and met imaging requirements. Micro particle-image velocimetry (micro-PIV was used to provide a detailed characterization of flows in the new design. Simulated and experimental results demonstrate that a trapezoidal side chamber represents a viable option for accomplishing controlled single cell rotation. Further, agreement between experimental and simulated results confirms that numerical simulation is an effective method for chamber design.

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1984-01-01

Conceptual Design of Fusion Experimental Reactor (FER) of which the objective will be to realize self-ignition with D-T reaction is reported. Mechanical Configurations of FER are characterized with a noncircular plasma and a double-null divertor. The primary aim of design studies is to demonstrate fissibility of reactor structures as compact and simple as possible with removable torus sectors. The structures of each component such as a first-wall, blanket, shielding, divertor, magnet and so on have been designed. It is also discussed about essential reactor plant system requirements. In addition to the above, a brief concept of a steady-state reactor based on RF current drive is also discussed. The main aim, in this time, is to examine physical studies of a possible RF steady-state reactor. (author)

Experimental validation of a new heterogeneous mechanical test design

Science.gov (United States)

Aquino, J.; Campos, A. Andrade; Souto, N.; Thuillier, S.

2018-05-01

Standard material parameters identification strategies generally use an extensive number of classical tests for collecting the required experimental data. However, a great effort has been made recently by the scientific and industrial communities to support this experimental database on heterogeneous tests. These tests can provide richer information on the material behavior allowing the identification of a more complete set of material parameters. This is a result of the recent development of full-field measurements techniques, like digital image correlation (DIC), that can capture the heterogeneous deformation fields on the specimen surface during the test. Recently, new specimen geometries were designed to enhance the richness of the strain field and capture supplementary strain states. The butterfly specimen is an example of these new geometries, designed through a numerical optimization procedure where an indicator capable of evaluating the heterogeneity and the richness of strain information. However, no experimental validation was yet performed. The aim of this work is to experimentally validate the heterogeneous butterfly mechanical test in the parameter identification framework. For this aim, DIC technique and a Finite Element Model Up-date inverse strategy are used together for the parameter identification of a DC04 steel, as well as the calculation of the indicator. The experimental tests are carried out in a universal testing machine with the ARAMIS measuring system to provide the strain states on the specimen surface. The identification strategy is accomplished with the data obtained from the experimental tests and the results are compared to a reference numerical solution.

Bayesian Optimal Experimental Design Using Multilevel Monte Carlo

KAUST Repository

Ben Issaid, Chaouki; Long, Quan; Scavino, Marco; Tempone, Raul

2015-01-01

Experimental design is very important since experiments are often resource-exhaustive and time-consuming. We carry out experimental design in the Bayesian framework. To measure the amount of information, which can be extracted from the data in an experiment, we use the expected information gain as the utility function, which specifically is the expected logarithmic ratio between the posterior and prior distributions. Optimizing this utility function enables us to design experiments that yield the most informative data for our purpose. One of the major difficulties in evaluating the expected information gain is that the integral is nested and can be high dimensional. We propose using Multilevel Monte Carlo techniques to accelerate the computation of the nested high dimensional integral. The advantages are twofold. First, the Multilevel Monte Carlo can significantly reduce the cost of the nested integral for a given tolerance, by using an optimal sample distribution among different sample averages of the inner integrals. Second, the Multilevel Monte Carlo method imposes less assumptions, such as the concentration of measures, required by Laplace method. We test our Multilevel Monte Carlo technique using a numerical example on the design of sensor deployment for a Darcy flow problem governed by one dimensional Laplace equation. We also compare the performance of the Multilevel Monte Carlo, Laplace approximation and direct double loop Monte Carlo.

Bayesian Optimal Experimental Design Using Multilevel Monte Carlo

KAUST Repository

Ben Issaid, Chaouki

2015-01-07

Experimental design is very important since experiments are often resource-exhaustive and time-consuming. We carry out experimental design in the Bayesian framework. To measure the amount of information, which can be extracted from the data in an experiment, we use the expected information gain as the utility function, which specifically is the expected logarithmic ratio between the posterior and prior distributions. Optimizing this utility function enables us to design experiments that yield the most informative data for our purpose. One of the major difficulties in evaluating the expected information gain is that the integral is nested and can be high dimensional. We propose using Multilevel Monte Carlo techniques to accelerate the computation of the nested high dimensional integral. The advantages are twofold. First, the Multilevel Monte Carlo can significantly reduce the cost of the nested integral for a given tolerance, by using an optimal sample distribution among different sample averages of the inner integrals. Second, the Multilevel Monte Carlo method imposes less assumptions, such as the concentration of measures, required by Laplace method. We test our Multilevel Monte Carlo technique using a numerical example on the design of sensor deployment for a Darcy flow problem governed by one dimensional Laplace equation. We also compare the performance of the Multilevel Monte Carlo, Laplace approximation and direct double loop Monte Carlo.

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .2. DESIGN EVALUATION ON MEASURED DATA

NARCIS (Netherlands)

DUINEVELD, C. A. A.; Smilde, A. K.; Doornbos, D. A.

1993-01-01

The construction of a small experimental design for a combination of process and mixture variables is a problem which has not been solved completely by now. In a previous paper we evaluated some designs with theoretical measures. This second paper evaluates the capabilities of the best of these

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .2. DESIGN EVALUATION ON MEASURED DATA

NARCIS (Netherlands)

DUINEVELD, CAA; SMILDE, AK; DOORNBOS, DA

The construction of a small experimental design for a combination of process and mixture variables is a problem which has not been solved completely by now. In a previous paper we evaluated some designs with theoretical measures. This second paper evaluates the capabilities of the best of these

The Single-Phase ProtoDUNE Technical Design Report

Energy Technology Data Exchange (ETDEWEB)

Abi, B. [Univ. of Padova (Italy); et al.

2017-06-21

ProtoDUNE-SP is the single-phase DUNE Far Detector prototype that is under construction and will be operated at the CERN Neutrino Platform (NP) starting in 2018. ProtoDUNE-SP, a crucial part of the DUNE effort towards the construction of the first DUNE 10-kt fiducial mass far detector module (17 kt total LAr mass), is a significant experiment in its own right. With a total liquid argon (LAr) mass of 0.77 kt, it represents the largest monolithic single-phase LArTPC detector to be built to date. It's technical design is given in this report.

Precast concrete sandwich panels subjected to impact loading

Science.gov (United States)

Runge, Matthew W.

Precast concrete sandwich panels are a relatively new product in the construction industry. The design of these panels incorporates properties that allow for great resilience against temperature fluctuation as well as the very rapid and precise construction of facilities. The concrete sandwich panels investigated in this study represent the second generation of an ongoing research and development project. This second generation of panels have been engineered to construct midsized commercial buildings up to three stories in height as well as residential dwellings. The panels consist of a double-tee structural wythe, a foam core and a fascia wythe, joined by shear connectors. Structures constructed from these panels may be subjected to extreme loading including the effects of seismic and blast loading in addition to wind. The aim of this work was to investigate the behaviour of this particular sandwich panel when subjected to structural impact events. The experimental program consisted of fourteen concrete sandwich panels, five of which were considered full-sized specimens (2700 mm X 1200mm X 270 mm) and nine half-sized specimens (2700mm X 600mm X 270 mm) The panels were subjected to impact loads from a pendulum impact hammer where the total energy applied to the panels was varied by changing the mass of the hammer. The applied loads, displacements, accelerations, and strains at the mid-span of the panel as well as the reaction point forces were monitored during the impact. The behaviour of the panels was determined primarily from the experimental results. The applied loads at low energy levels that caused little to no residual deflection as well as the applied loads at high energy levels that represent catastrophic events and thus caused immediate failure were determined from an impact on the structural and the fascia wythes. Applied loads at intermediate energy levels representing extreme events were also used to determine whether or not the panels could withstand

MYRRHA/XT-ADS primary system design and experimental devices

International Nuclear Information System (INIS)

Maes, D.

2009-01-01

The EUROTRANS project is an integrated project in the Sixth European Framework Program in the context of Partitioning and Transmutation. The objective of this project is to work towards an ETD (European Transmutation Demonstration) in a step-wise manner. The first step is to carry out an advanced design of a small-scale XT-ADS (eXperimental Transmutation in an Accelerator Driven System) for realisation in a short-term (about 10 years) as well as to accomplish a generic conceptual design of EFIT (European Facility for Industrial Transmutation) for realisation in the long-term. The MYRRHA-2005 design served as a starting basis for the XT-ADS. Many options have been revisited and the framework is now set up. While the MYRRHA-2005 design was still a conceptual design, the intention is to get at the end of the EUROTRANS project (March 2009) an advanced design of the XT-ADS, albeit a first advanced design. While the design work performed during the first years of the project (2005-2006) was mainly devoted to optimise and enhance the primary and secondary system configuration according to the suggestions and contributions of our industrial partners (Ansaldo Nucleare, Areva, Suez-Tractebel) within the DM1 (Domain 1 D ESIGN ) , the last year work objectives mainly consisted of (1) the release of the Remote Handling Design Catalogue for XT-ADS and (2) the formulation of the specification of the experimental devices according to the XT-ADS objectives and adapted to the actual XT-ADS core and core support structure design; (3) the detailed calculations of the main XT-ADS primary and secondary system components

The effect of electroacupuncture and tramadol on experimental tourniquet pain.

Science.gov (United States)

Musial, Frauke; Choi, Kyung-Eun; Gabriel, Tim; Lüdtke, Rainer; Rampp, Thomas; Michalsen, Andreas; Dobos, Gustav

2012-03-01

The hypoalgesic effect of electroacupuncture (EA) was directly compared with the analgesic effect of pharmacological interventions using the submaximum effort tourniquet technique (SETT). 125 healthy subjects (mean age 24.44±4.46 years; 62.4% female, 37.6% male) performed SETT at baseline and under one of five experimental conditions (n=25 per group): EA (2 Hz with burst pulses in alternating one-phase-square wave pulses; burst length 180 μs, burst frequency 80 Hz, stimulation time/pulse width 3 s), tramadol (50 mg), ibuprofen (400 mg), placebo pill or non-treatment control. EA was performed at LI4 and LI10 contralaterally with stimulation beginning 20 min before SETT and lasting throughout SETT. The pharmacological interventions were given in a double-blind design 1 h before the SETT assessment. Subjects showed a hypoalgesic effect of the opiate and of the EA for subjective pain rating (EA p=0.0051; tramadol p=0.0299), and pain tolerance index (time/rating) (EA p=0.043; tramadol p=0.047) analysed using analysis of covariance. More subjects reached the strict time limit of 30 min (analysed by logistic regression and adjusted OR as a post-hoc analysis) under EA compared with most other experimental conditions. Only EA and tramadol were not significantly different (95% Wald confidence limits: non-treatment control vs EA 0.011 to 0.542; placebo pill vs EA 0.009 to 0.438; ibuprofen vs EA 0.021 to 0.766; tramadol vs EA 0.065 to 1.436). In a laboratory setting, an EA procedure was as effective as a single dose of an orally administered opiate in reducing experimentally induced ischaemic pain.

Hierarchical adaptive experimental design for Gaussian process emulators

International Nuclear Information System (INIS)

Busby, Daniel

2009-01-01

Large computer simulators have usually complex and nonlinear input output functions. This complicated input output relation can be analyzed by global sensitivity analysis; however, this usually requires massive Monte Carlo simulations. To effectively reduce the number of simulations, statistical techniques such as Gaussian process emulators can be adopted. The accuracy and reliability of these emulators strongly depend on the experimental design where suitable evaluation points are selected. In this paper a new sequential design strategy called hierarchical adaptive design is proposed to obtain an accurate emulator using the least possible number of simulations. The hierarchical design proposed in this paper is tested on various standard analytic functions and on a challenging reservoir forecasting application. Comparisons with standard one-stage designs such as maximin latin hypercube designs show that the hierarchical adaptive design produces a more accurate emulator with the same number of computer experiments. Moreover a stopping criterion is proposed that enables to perform the number of simulations necessary to obtain required approximation accuracy.

Design, construction and testing of a radon experimental chamber

International Nuclear Information System (INIS)

Chavez B, A.; Balcazar G, M.

1991-10-01

To carry out studies on the radon behavior under controlled and stable conditions it was designed and constructed a system that consists of two parts: a container of mineral rich in Uranium and an experimentation chamber with radon united one to the other one by a step valve. The container of uranium mineral approximately contains 800 gr of uranium with a law of 0.28%; the radon gas emanated by the mineral is contained tightly by the container. When the valve opens up the radon gas it spreads to the radon experimental chamber; this contains 3 accesses that allow to install different types of detectors. The versatility of the system is exemplified with two experiments: 1. With the radon experimental chamber and an associated spectroscopic system, the radon and two of its decay products are identified. 2. The design of the system allows to couple the mineral container to other experimental geometries to demonstrate this fact it was coupled and proved a new automatic exchanger system of passive detectors of radon. The results of the new automatic exchanger system when it leave to flow the radon freely among the container and the automatic exchanger through a plastic membrane of 15 m. are shown. (Author)

Statistical experimental design for refractory coatings

International Nuclear Information System (INIS)

McKinnon, J.A.; Standard, O.C.

2000-01-01

The production of refractory coatings on metal casting moulds is critically dependent on the development of suitable rheological characteristics, such as viscosity and thixotropy, in the initial coating slurry. In this paper, the basic concepts of mixture design and analysis are applied to the formulation of a refractory coating, with illustration by a worked example. Experimental data of coating viscosity versus composition are fitted to a statistical model to obtain a reliable method of predicting the optimal formulation of the coating. Copyright (2000) The Australian Ceramic Society

Experimental study on heavy-ion single event effect on nanometer DDR SRAM

International Nuclear Information System (INIS)

Luo Yinhong; Zhang Fengqi; Guo Hongxia; Zhou Hui; Wang Yanping; Zhang Keying

2013-01-01

Single event effect experimental study on 90 nm and 65 nm DDR SRAM were carried out, single event upset (SEU) cross section was discussed as a function of several parameters such as feature size, test pattern, incidence angle, supply voltage. Key influence factors and effect rule were analyzed. Feasibility of the current test method was discussed. Results indicate that, SEU cross section reduces as technologies scale down; the influence of test pattern and power supply on SEU cross section is small; tilt angle increases SEU cross section due to multiple upset increasement. The applicability of cosine tilt test method is correlative to ion species and linear energy transfer (LET) values. (authors)

Subjective evaluation of HEVC in mobile devices

Science.gov (United States)

Garcia, Ray; Kalva, Hari

2013-03-01

Mobile compute environments provide a unique set of user needs and expectations that designers must consider. With increased multimedia use in mobile environments, video encoding methods within the smart phone market segment are key factors that contribute to positive user experience. Currently available display resolutions and expected cellular bandwidth are major factors the designer must consider when determining which encoding methods should be supported. The desired goal is to maximize the consumer experience, reduce cost, and reduce time to market. This paper presents a comparative evaluation of the quality of user experience when HEVC and AVC/H.264 video coding standards were used. The goal of the study was to evaluate any improvements in user experience when using HEVC. Subjective comparisons were made between H.264/AVC and HEVC encoding standards in accordance with Doublestimulus impairment scale (DSIS) as defined by ITU-R BT.500-13. Test environments are based on smart phone LCD resolutions and expected cellular bit rates, such as 200kbps and 400kbps. Subjective feedback shows both encoding methods are adequate at 400kbps constant bit rate. However, a noticeable consumer experience gap was observed for 200 kbps. Significantly less H.264 subjective quality is noticed with video sequences that have multiple objects moving and no single point of visual attraction. Video sequences with single points of visual attraction or few moving objects tended to have higher H.264 subjective quality.

Cost, performance, and esthetic impacts of an experimental forest road in Montana

Science.gov (United States)

Rulon B. Gardner

1978-01-01

An experimental logging road designed to minimize environmental and esthetic impact was constructed in northwest Montana. The road was single-lane (14-foot finished surface, 3-foot ditch), constructed along the contour. Esthetically, the single-lane experimental road was judged far superior to existing roads on the forest.

Experimental study on behavior of RC panels covered with steel plates subjected to missile impact

International Nuclear Information System (INIS)

Jun Hashimoto; Katsuki Takiguchi; Koshiro Nishimura; Kazuyuki Matsuzawa; Mayuko Tsutsui; Yasuhiro Ohashi; Isao Kojima; Haruhiko Torita

2005-01-01

This paper describes an experimental study on the behavior of concrete panels with steel plate subjected to missile impact. Two tests were carried out, divided in accordance with the types of projectile, non-deformable and deformable. In all, 40 specimens of 750 mm square were prepared. The panel specimen was suspended vertically by two steel wire ropes to allow free movement after projectile impact, and was subjected to a projectile. As a result, it is confirmed that a RC panel with steel plate on its back side has higher impact resistance performance than a RC panel and that thickness of concrete panel, thickness of steel plate and the impact velocity of the projectile have a great effect on the failure modes of steel concrete panels. Moreover, based on the experimental results, the quantitative evaluation method for impact resistance performance of RC panels covered with steel plates is examined. The formula for perforation velocity of a half steel concrete panel, proposed in accordance with the bulging height, is effective to evaluate the impact resistance performance of RC panels with steel plates. (authors)

Subjective and Objective Quality Assessment of Single-Channel Speech Separation Algorithms

DEFF Research Database (Denmark)

Mowlaee, Pejman; Saeidi, Rahim; Christensen, Mads Græsbøll

2012-01-01

Previous studies on performance evaluation of single-channel speech separation (SCSS) algorithms mostly focused on automatic speech recognition (ASR) accuracy as their performance measure. Assessing the separated signals by different metrics other than this has the benefit that the results...... are expected to carry on to other applications beyond ASR. In this paper, in addition to conventional speech quality metrics (PESQ and SNRloss), we also evaluate the separation systems output using different source separation metrics: blind source separation evaluation (BSS EVAL) and perceptual evaluation...... that PESQ and PEASS quality metrics predict well the subjective quality of separated signals obtained by the separation systems. From the results it is observed that the short-time objective intelligibility (STOI) measure predict the speech intelligibility results....

CRISPR library designer (CLD): software for multispecies design of single guide RNA libraries.

Science.gov (United States)

Heigwer, Florian; Zhan, Tianzuo; Breinig, Marco; Winter, Jan; Brügemann, Dirk; Leible, Svenja; Boutros, Michael

2016-03-24

Genetic screens using CRISPR/Cas9 are a powerful method for the functional analysis of genomes. Here we describe CRISPR library designer (CLD), an integrated bioinformatics application for the design of custom single guide RNA (sgRNA) libraries for all organisms with annotated genomes. CLD is suitable for the design of libraries using modified CRISPR enzymes and targeting non-coding regions. To demonstrate its utility, we perform a pooled screen for modulators of the TNF-related apoptosis inducing ligand (TRAIL) pathway using a custom library of 12,471 sgRNAs. CLD predicts a high fraction of functional sgRNAs and is publicly available at https://github.com/boutroslab/cld.

Single-dose FTY720 pharmacokinetics, food effect, and pharmacological responses in healthy subjects

Science.gov (United States)

Kovarik, John M; Schmouder, Robert; Barilla, Denise; Wang, Yibin; Kraus, Gerolf

2004-01-01

Aims FTY720 is a sphingosine-1-phosphate receptor agonist that redirects lymphocytes from the circulation to lymph nodes without impairing lymphocyte function. It is being developed as an immunomodulator for the prevention of acute rejection after organ transplantation. This study was performed to provide guidance on administration with respect to meals and to measure pharmacologic responses in healthy subjects. Methods In this randomized, two-period, crossover study, 14 healthy subjects received placebo on day −1 of each period with baseline circadian measurements of lymphocyte count and heart rate. Subjects subsequently received a single 1 mg oral dose of FTY720 on day 1 under fasting conditions and after a high fat meal. Blood FTY720 concentrations, lymphocyte count, and supine heart rate were assessed over an 8 day period after each FTY720 dose. The effect of food on FTY720 pharmacokinetics was assessed by standard bioequivalence testing. Results Both the peak concentration (0.65 ± 0.17 vs 0.64 ± 0.18 ng ml−1) and total exposure (AUC 149 ± 65 vs 139 ± 43 ng ml−1 h) did not differ significantly between fasting and fed states, respectively. The corresponding fed/fasting ratios and 90% confidence intervals were 1.00 (0.86, 1.17) for Cmax and 0.98 (0.86, 1.11) for AUC. Under both treatment conditions peripheral blood lymphocyte count decreased from baseline by 38 ± 9% over the first 2 days postdose and then increased towards predose values over the subsequent week. Whereas a circadian rhythm in supine heart rate was preserved in the presence of FTY720, the heart rate vs time curve was shifted downwards by 10% over the first day postdose and then recovered to prestudy values by days 3–5 postdose. These changes were asymptomatic. Conclusions Single 1 mg doses of FTY720 were well tolerated in healthy subjects and elicited a moderate decrease in peripheral blood lymphocyte count and a transient decrease in heart rate consistent with its pharmacological

Optimizing laboratory animal stress paradigms: The H-H* experimental design.

Science.gov (United States)

McCarty, Richard

2017-01-01

Major advances in behavioral neuroscience have been facilitated by the development of consistent and highly reproducible experimental paradigms that have been widely adopted. In contrast, many different experimental approaches have been employed to expose laboratory mice and rats to acute versus chronic intermittent stress. An argument is advanced in this review that more consistent approaches to the design of chronic intermittent stress experiments would provide greater reproducibility of results across laboratories and greater reliability relating to various neural, endocrine, immune, genetic, and behavioral adaptations. As an example, the H-H* experimental design incorporates control, homotypic (H), and heterotypic (H*) groups and allows for comparisons across groups, where each animal is exposed to the same stressor, but that stressor has vastly different biological and behavioral effects depending upon each animal's prior stress history. Implementation of the H-H* experimental paradigm makes possible a delineation of transcriptional changes and neural, endocrine, and immune pathways that are activated in precisely defined stressor contexts. Copyright © 2016 Elsevier Ltd. All rights reserved.

Picture Exchange Communication System with Individuals with Developmental Disabilities: A Meta-Analysis of Single Subject Studies

Science.gov (United States)

Hart, Stephanie L.; Banda, Devender R.

2010-01-01

Picture Exchange Communication System (PECS) is a picture-based communication strategy used to teach communication skills to persons with developmental disabilities including autism. This article systematically reviews 13 published single-subject studies to examine the effectiveness of PECS, the effects of PECS on speech and problem behaviors,…

Experimental study of the single electron response of the DELPHI Barrel RICH MWPC's

International Nuclear Information System (INIS)

Dracos, M.

1989-01-01

We present herewith the results of an experimental study of the multiwire proportionnal chambers (MWPC's) used in the Barrel RICH particle identifier of the LEP-DELPHI experiment. Emphasis is given to the problem of detection efficiency and to the measurements of the charge induced by a single photoelectron

Randomization and Data-Analysis Items in Quality Standards for Single-Case Experimental Studies

Science.gov (United States)

Heyvaert, Mieke; Wendt, Oliver; Van den Noortgate, Wim; Onghena, Patrick

2015-01-01

Reporting standards and critical appraisal tools serve as beacons for researchers, reviewers, and research consumers. Parallel to existing guidelines for researchers to report and evaluate group-comparison studies, single-case experimental (SCE) researchers are in need of guidelines for reporting and evaluating SCE studies. A systematic search was…

Key issues in european reactor seismic design

International Nuclear Information System (INIS)

Cicognani, G.; Martelli, A.

1984-01-01

The paper focuses on the main problems which have arisen in FBR design in Europe due to seismic conditions. Its first part, derived from the final report of a CEC-Belgonucleaire study contract, clarifies how ''real'' is the seismic problem for each site. Then, the second and main part deals with the studies carried out in the european countries on the relevant subjects, typical of FBRs or related to specific needs of single FBRs: these studies, for which contributions were provided by ENEA, CEA, NNC and INTERATOM, concern mainly the numerical and experimental analysis of the core, the reactor vessel, the shut-down system and the reactor building of FBRs under construction or in advanced design phase. Attention is also paid to the studies started for future purposes, the feed-backs on the design due to seismic conditions, and the instructions for future reactors

Experimental study of single-electron loss by Ar+ ions in rare-gas atoms

Science.gov (United States)

Reyes, P. G.; Castillo, F.; Martínez, H.

2001-04-01

Absolute differential and total cross sections for single-electron loss were measured for Ar+ ions on rare-gas atoms in the laboratory energy range of 1.5 to 5.0 keV. The electron loss cross sections for all the targets studied are found to be in the order of magnitude between 10-19 and 10-22 cm2, and show a monotonically increasing behaviour as a function of the incident energy. The behaviour of the total single-electron loss cross sections with the atomic target number, Zt, shows different dependences as the collision energy increases. In all cases the present results display experimental evidence of saturation in the single-electron loss cross section as the atomic number of the target increases.

Randomizing Roaches: Exploring the "Bugs" of Randomization in Experimental Design

Science.gov (United States)

Wagler, Amy; Wagler, Ron

2014-01-01

Understanding the roles of random selection and random assignment in experimental design is a central learning objective in most introductory statistics courses. This article describes an activity, appropriate for a high school or introductory statistics course, designed to teach the concepts, values and pitfalls of random selection and assignment…

Optimal Multitrial Prediction Combination and Subject-Specific Adaptation for Minimal Training Brain Switch Designs

NARCIS (Netherlands)

Spyrou, L.; Blokland, Y.M.; Farquhar, J.D.R.; Bruhn, J.

2016-01-01

Brain-Computer Interface (BCI) systems are traditionally designed by taking into account user-specific data to enable practical use. More recently, subject independent (SI) classification algorithms have been developed which bypass the subject specific adaptation and enable rapid use of the system.

Optimal multitrial prediction combination and subject-specific adaptation for minimal training brain switch designs

NARCIS (Netherlands)

Spyrou, L.; Blokland, Y.M.; Farquhar, J.D.R.; Bruhn, J.

2016-01-01

Brain-Computer Interface systems are traditionally designed by taking into account user-specific data to enable practical use. More recently, subject independent (SI) classification algorithms have been developed which bypass the subject specific adaptation and enable rapid use of the system. A

Experimental Study and Comparison of Various Designs of Gas Flow Fields to PEM Fuel Cells and Cell Stack Performance

International Nuclear Information System (INIS)

Liu, Hong; Li, Peiwen; Juarez-Robles, Daniel; Wang, Kai; Hernandez-Guerrero, Abel

2014-01-01

In this study, a significant number of experimental tests to proton exchange membrane (PEM) fuel cells were conducted to investigate the effect of gas flow fields on fuel cell performance. Graphite plates with various flow field or flow channel designs, from literature survey and also novel designs by the authors, were used for the PEM fuel cell assembly. The fabricated fuel cells have an effective membrane area of 23.5 cm 2 . The results showed that the serpentine flow channel design is still favorable, giving the best single fuel cell performance amongst all the studied flow channel designs. A novel symmetric serpentine flow field was proposed for a relatively large sized fuel cell application. Four fuel cell stacks each including four cells were assembled using different designs of serpentine flow channels. The output power performances of fuel cell stacks were compared and the novel symmetric serpentine flow field design is recommended for its very good performance.

Experimental Investigation and Discrete Element Modelling of Composite Hollow Spheres Subjected to Dynamic Fracture

Directory of Open Access Journals (Sweden)

Arthur Coré

2017-01-01

Full Text Available This paper deals with the characterization and the numerical modelling of the collapse of composite hollow spherical structures developed to absorb energy during high velocity impacts. The structure is composed of hollow spheres (ϕ=2–30 mm made of epoxy resin and mineral powder. First of all, quasi-static and dynamic (v=5 mm·min−1 to v=2 m·s−1 compression tests are conducted at room temperature on a single sphere to study energy dissipation mechanisms. Fracture of the material appears to be predominant. A numerical model based on the discrete element method is investigated to simulate the single sphere crushing. The stress-strain-time relationship of the material based on the Ree-Eyring law is numerically implemented. The DEM modelling takes naturally into account the dynamic fracture and the crack path computed is close to the one observed experimentally in uniaxial compression. Eventually, high velocity impacts (v>100 m·s−1 of a hollow sphere on a rigid surface are conducted with an air cannon. The numerical results are in good agreement with the experimental data and demonstrate the ability of the present model to correctly describe the mechanical behavior of brittle materials at high strain rate.

Autogenic-Feedback Training (AFT) as a preventive method for space motion sickness: Background and experimental design

Science.gov (United States)

Cowings, Patricia S.; Toscano, William B.

1993-01-01

Finding an effective treatment for the motion sickness-like symptoms that occur in space has become a high priority for NASA. The background research is reviewed and the experimental design of a formal life sciences shuttle flight experiment designed to prevent space motion sickness in shuttle crew members is presented. This experiment utilizes a behavioral medicine approach to solving this problem. This method, Autogenic-Feedback Training (AFT), involves training subjects to voluntarily control several of their own physiological responses to environmental stressors. AFT has been used reliably to increase tolerance to motion sickness during ground-based tests in over 200 men and women under a variety of conditions that induce motion sickness, and preliminary evidence from space suggests that AFT may be an effective treatment for space motion sickness as well. Proposed changes to this experiment for future manifests are included.

Radiation hardening at 77 K in Zn and Cu single crystals at low doses

International Nuclear Information System (INIS)

Gonzalez, H.C.; Bisogni, E.A.

1980-01-01

There is controversy about radiation hardening phenomenon and its additivity with other hardening mechanisms. The purpose of this work is to contribute to the understanding of this subject, through measurements made in Zn and Cu single crystals. Post-irradiation measurements of yield stress of Zn, made on different single crystals, show a direct proportionality to the 0.5 power of the dose. It is determined that for a dose greater than 3.7 x 10 16 neutrons cm -2 s -1 there is always cleavage. The maximum critical resolved shear stress measured is about 8.82 MPa. In order to study additivity it is necessary to lower experimental errors. A micro tensile machine is designed to operate in the CNEA facility RA1 in a bath of liquid N 2 . Experimental measurements of yield stress with dose are carried out in-situ on the same single crystals. Experimental results on Cu and Zn show that radiation induced yield stress increases with a 0.5 power law. It must be taken into account that the definition of radiation induced yield stress stands for radiation created obstacles operating alone. The radiation induced yield stress adds algebraically to the athermal component of the initial yield stress but is not exactly additive to the other thermally activated mechanisms. A gradual transition from one to the other type of obstacles is observed. (author)

The Single-Case Reporting Guideline in BEhavioural Interventions (SCRIBE) 2016 Statement

Science.gov (United States)

Tate, Robyn L.; Perdices, Michael; Rosenkoetter, Ulrike; Shadish, William; Vohra, Sunita; Barlow, David H.; Horner, Robert; Kazdin, Alan; Kratochwill, Thomas; McDonald, Skye; Sampson, Margaret; Shamseer, Larissa; Togher, Leanne; Albin, Richard; Backman, Catherine; Douglas, Jacinta; Evans, Jonathan J.; Gast, David; Manolov, Rumen; Mitchell, Geoffrey; Nickels, Lyndsey; Nikles, Jane; Ownsworth, Tamara; Rose, Miranda; Schmid, Christopher H.; Wilson, Barbara

2016-01-01

We developed a reporting guideline to provide authors with guidance about what should be reported when writing a paper for publication in a scientific journal using a particular type of research design: the single-case experimental design. This report describes the methods used to develop the Single-Case Reporting guideline In BEhavioural…

Providing guidance in virtual lab experimentation : the case of an experiment design tool

NARCIS (Netherlands)

Efstathiou, Charalampos; Hovardas, Tasos; Xenofontos, Nikoletta A.; Zacharia, Zacharias C.; de Jong, Ton A.J.M.; Anjewierden, Anjo; van Riesen, Siswa A.N.

2018-01-01

The present study employed a quasi-experimental design to assess a computer-based tool, which was intended to scaffold the task of designing experiments when using a virtual lab for the process of experimentation. In particular, we assessed the impact of this tool on primary school students’

Experimental Implementation of a Low-Cost Single Phase Five-Level Inverter for Autonomous PV System Applications Without Batteries

Directory of Open Access Journals (Sweden)

A. Nouaiti

2018-02-01

Full Text Available This paper presents the design and the implementation of a low-cost single phase five-level inverter for photovoltaic applications. The proposed multilevel inverter is composed of a simple boost converter, a switched-capacitor converter, and an H-bridge converter. An efficient control method which associates a closed-loop regulation method with a simple maximum power point tracking (MPPT method is applied in order to allow the proposed multilevel inverter to transfer power energy from solar panels to autonomous load with no storage batteries. An experimental prototype of this inverter is fabricated at the laboratory and tested with a digital control system. Obtained results confirm the simplicity and the performance of the proposed photovoltaic system.

First experimental observation of double-photon Compton scattering using single gamma detector

International Nuclear Information System (INIS)

Sandhu, B.S.; Saddi, M.B.; Singh, B.; Ghumman, B.S.

2003-01-01

Full text: The phenomenon of double-photon Compton scattering has been successfully observed using single gamma detector, a technique avoiding the use of complicated slow-fast coincidence set-up used till now for observing this higher order process. Here doubly differentiated collision cross-section integrated over direction of one of the two final photons, the direction of other one being kept fixed, has been measured experimentally for 0.662 MeV incident gamma photons. The energy spectra of the detected photons are observed as a long tail to the single-photon Compton line on the lower side of the full energy peak in the recorded scattered energy spectrum. The present results are in agreement with theory of this process

Scaffolded Instruction Improves Student Understanding of the Scientific Method & Experimental Design

Science.gov (United States)

D'Costa, Allison R.; Schlueter, Mark A.

2013-01-01

Implementation of a guided-inquiry lab in introductory biology classes, along with scaffolded instruction, improved students' understanding of the scientific method, their ability to design an experiment, and their identification of experimental variables. Pre- and postassessments from experimental versus control sections over three semesters…

Experimental and numerical investigation of slabs on ground subjected to concentrated loads

Science.gov (United States)

Øverli, Jan

2014-09-01

An experimental program is presented where a slab on ground is subjected to concentrated loading at the centre, the edges and at the corners. Analytical solutions for the ultimate load capacity fit well with the results obtained in the tests. The non-linear behaviour of the slab is captured by performing nonlinear finite element analyses. The soil is modelled as a no-tension bedding and a smeared crack approach is employed for the concrete. Through a parametric study, the finite element model has been used to assess the influence of subgrade stiffness and shrinkage. The results indicate that drying shrinkage can cause severe cracking in slabs on grade.

Single case design studies in music therapy: resurrecting experimental evidence in small group and individual music therapy clinical settings.

Science.gov (United States)

Geist, Kamile; Hitchcock, John H

2014-01-01

The profession would benefit from greater and routine generation of causal evidence pertaining to the impact of music therapy interventions on client outcomes. One way to meet this goal is to revisit the use of Single Case Designs (SCDs) in clinical practice and research endeavors in music therapy. Given the appropriate setting and goals, this design can be accomplished with small sample sizes and it is often appropriate for studying music therapy interventions. In this article, we promote and discuss implementation of SCD studies in music therapy settings, review the meaning of internal study validity and by extension the notion of causality, and describe two of the most commonly used SCDs to demonstrate how they can help generate causal evidence to inform the field. In closing, we describe the need for replication and future meta-analysis of SCD studies completed in music therapy settings. SCD studies are both feasible and appropriate for use in music therapy clinical practice settings, particularly for testing effectiveness of interventions for individuals or small groups. © the American Music Therapy Association 2014. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

A study on fatigue crack growth behavior subjected to a single tensile overload

International Nuclear Information System (INIS)

Lee, S.Y.; Liaw, P.K.; Choo, H.; Rogge, R.B.

2011-01-01

Neutron diffraction and electric potential experiments were carried out to investigate the growth behavior of a fatigue crack subjected to a single tensile overload. The specific objectives were to (i) probe the crack tip deformation and fracture behaviors under applied loads; (ii) examine the overload-induced transient crack growth micromechanism; (iii) validate the effective stress intensity factor range based on the crack closure approach as the fatigue crack tip driving force; and (iv) establish a quantitative relationship between the crack tip driving force and crack growth behavior. Immediately after a single tensile overload was introduced and then unloaded, the crack tip became blunt and enlarged compressive residual stresses in both magnitude and zone size were observed around the crack tip. The results show that the combined contributions of the overload-induced enlarged compressive residual stresses and crack tip blunting with secondary cracks are responsible for the observed changes in the crack opening load and the resultant post-overload transient crack growth behavior.

Experimental demonstration of a simple displacement sensor based on a bent single-mode–multimode–single-mode fiber structure

International Nuclear Information System (INIS)

Wu, Qiang; Semenova, Yuliya; Wang, Pengfei; Hatta, Agus Muhamad; Farrell, Gerald

2011-01-01

A simple displacement sensor based on a bent single-mode–multimode–single-mode (SMS) fiber structure is proposed and experimentally investigated. The sensor offers a wider displacement range, not limited by the risk of fiber breakage, as well as a three-fold increase in displacement sensitivity by comparison with a straight SMS structure sensor. This sensor can be interrogated by either an optical spectral analyzer (OSA) or a ratiometric interrogation system: (1) if interrogated by an OSA assuming a resolution of 1 pm, it has a sensitivity of 28.2 nm for a displacement measurement range from 0 to 280 µm; (2) if interrogated by a ratiometric interrogation system, it has worst and best case resolutions of 556 and 38 nm, respectively, for a displacement measurement range from 0 to 520 µm

Experimental design rules for implementing biconically tapered single mode optical fibre displacement sensors

Science.gov (United States)

Arregui, Francisco J.; Matias, Ignacio R.; Bariain, Candido; Lopez-Amo, Manuel

1998-06-01

Tapered optical fibers are used to design couplers, wavelength division multiplexers, near field scanning optical microscopy, just to mention a few. Moreover, and due to its strong transmission dependence to external medium the tapered fiber may also be used to sense distinct parameters such as temperature, humidity, PH, etc. In this work bending effects in tapers are exploited to achieved displacement sensors and to present design rules for implementing these sensors according to the desired both range and sensitivity.

Optimal Experimental Design for Large-Scale Bayesian Inverse Problems

KAUST Repository

Ghattas, Omar

2014-01-01

We develop a Bayesian framework for the optimal experimental design of the shock tube experiments which are being carried out at the KAUST Clean Combustion Research Center. The unknown parameters are the pre-exponential parameters and the activation

Pet Bottle Design, Correlation Analysis Of Pet Bottle Characteristics Subjective Judgment

Directory of Open Access Journals (Sweden)

Darko Avramović

2012-06-01

Full Text Available Ability to predict consumer’s reaction to particular design solution of the product is very important. Gathering andanalysis of subjective judgments of particular characteristics, based on which the aesthetic of the product is judged,is one of predicting the consumer’s reaction in the future. Knowledge gathered this manner can serve as a referencefor further studies of determining factors for aesthetic results and design quality. There are two opposed opinionsregarding prediction of aesthetic impression. One opinion is that taste of individual cannot be discussed because itis extremely variable and the possibility of meaningful analysis of aesthetic impression is rejected. Other opinionstates that there is a consistent preference of certain aesthetic characteristics despite individual and group differences.Main goal of this paper is to examine the correlation between subjective judgments of certain PET bottlecharacteristics. Analysis showed meaningful correlation between some of the PET bottle characteristics while othercharacteristics showed less correlation. It can be concluded that not all of the characteristics have the same influenceon the aesthetics and design quality of the PET bottle form. Emphasizing the characteristics relative to aesthetics ofthe product can produce better market results, taking in to account that consumer’s buy the product they consider tobe more attractive if other parameters of the product are similar.

Design of all solid state tunable single-mode Ti: sapphire laser for nuclear industry

International Nuclear Information System (INIS)

Lee, J.H.; Nam, S.M.; Lee, Y.J.; Lee, J.M.; Horn, Roland E.; Wendt, Klaus

1999-01-01

We designed a Ti:Sapphire laser pumped by a diode laser pumped solid state laser (DPSSL). The DPSSL was intra-cavity frequency doubled and it had 20 W output power. The Ti:Sapphire laser was designed for single longitudinal mode lasing. For single mode lasing, the laser used several solid etalons. We simulated temporal evolution of the laser pulse and single pass amplification rate of the photons in each modes from rate equations. From the result, we found that single mode lasing is viable in this cavity

Experimental Study about Two-phase Damping Ratio on a Tube Bundle Subjected to Homogeneous Two-phase Flow

Energy Technology Data Exchange (ETDEWEB)

Sim, Woo Gun; Dagdan, Banzragch [Hannam Univ., Daejeon (Korea, Republic of)

2017-03-15

Two-phase cross flow exists in many shell-and-tube heat exchangers such as condensers, evaporators, and nuclear steam generators. The drag force acting on a tube bundle subjected to air/water flow is evaluated experimentally. The cylinders subjected to two-phase flow are arranged in a normal square array. The ratio of pitch to diameter is 1.35, and the diameter of the cylinder is 18 mm. The drag force along the flow direction on the tube bundles is measured to calculate the drag coefficient and the two-phase damping ratio. The two-phase damping ratios, given by the analytical model for a homogeneous two-phase flow, are compared with experimental results. The correlation factor between the frictional pressure drop and the hydraulic drag coefficient is determined from the experimental results. The factor is used to calculate the drag force analytically. It is found that with an increase in the mass flux, the drag force, and the drag coefficients are close to the results given by the homogeneous model. The result shows that the damping ratio can be calculated using the homogeneous model for bubbly flow of sufficiently large mass flux.

A single dose of dark chocolate increases parasympathetic modulation and heart rate variability in healthy subjects

Directory of Open Access Journals (Sweden)

Ana Amélia Machado DUARTE

Full Text Available ABSTRACT Objective: The aim of this study was to investigate the acute effect of a single dose of dark chocolate (70% cocoa on blood pressure and heart rate variability. Methods: Thirty-one healthy subjects (aged 18-25 years; both sexes were divided into two groups: 10 subjects in the white chocolate (7.4 g group and 21 in the dark chocolate (10 g group; measurements were performed at the university's physiology lab. An electrocardiogram measured the sympathovagal balance by spectral and symbolic analysis. Results: A single dose of dark chocolate significantly reduced systolic blood pressure and heart rate. After consuming 10 g of dark chocolate, significant increases were observed for heart rate variability, standard deviation of RR intervals standard deviation of all NN intervals, square root of the mean squared differences between adjacent normal RR intervals root mean square of successive differences, and an increase in the high frequency component in absolute values, representing the parasympathetic modulation. Conclusion: In conclusion the importance of our results lies in the magnitude of the response provoked by a single dose of cocoa. Just 10 g of cocoa triggered a significant increase in parasympathetic modulation and heart rate variability. These combined effects can potentially increase life expectancy because a reduction in heart rate variability is associated with several cardiovascular diseases and higher mortality.

INFLUENCE OF SUBJECT AND OBJECTIVES FACTORS OF INFORMATIZATION ON THE PEDAGOGICAL DESIGN EFFICIENCY

Directory of Open Access Journals (Sweden)

Tamara O. Pushkareva

2018-02-01

Full Text Available In this article, a preliminary terminological analysis of the conceptual apparatus in the direction of computer-oriented informatization of pedagogical designing of educational activity in the structure of general secondary education has been made. The influence of the subject and object factors of the informatization of the educational process on the efficiency of pedagogical design is investigated. The existence of a dual problem in the educational sphere, related both to the formatting of an effective informational and educational product, and to the technologically acceptable component of well-organized computer-oriented support for students, is established. It is carried out the analysis of priority in the perception of varieties of information by the subjects of the educational system, as well as revealed that in the perception of computer information by subjects of different status or age there are differences that are related to their individual needs, desires, inclinations. The means of informative support of educational process are considered and recommendations on their use are given.

Design of an Annular Disc Subject to Thermomechanical Loading

Directory of Open Access Journals (Sweden)

Sergei Alexandrov

2012-01-01

Full Text Available Two solutions to design a thin annular disc of variable thickness subject to thermomechanical loading are proposed. It is assumed that the thickness of the disc is everywhere sufficiently small for the stresses to be averaged through the thickness. The state of stress is plane. The initiation of plastic yielding is controlled by Mises yield criterion. The design criterion for one of the solutions proposed requires that the distribution of stresses is uniform over the entire disc. In this case there is a relation between optimal values of the loading parameters at the final stage. The specific shape of the disc corresponds to each pair of such parameters. The other solution is obtained under the additional requirement that the distribution of strains is uniform. This solution exists for the disc of constant thickness at specific values of the loading parameters.

XFEM Modelling of Multi-holes Plate with Single-row and Staggered Holes Configurations

Directory of Open Access Journals (Sweden)

Supar Khairi

2017-01-01

Full Text Available Joint efficiency is the key to composite structures assembly design, good structures response is dependent upon multi-holes behavior as subjected to remote loading. Current benchmarking work were following experimental testing series taken from literature on multi-holes problem. Eleven multi-hole configurations were investigated with various pitch and gage distance of staggered holes and non-staggered holes (single-row holes. Various failure modes were exhibited, most staggered holes demonstrates staggered crack path but non-staggered holes series displayed crack path along net-section plane. Stress distribution were carried out and good agreement were exhibited in experimental observation as reported in the respective literature. Consequently, strength prediction work were carried out under quasi-static loading, most showed discrepancy between 8% -31%, better prediction were exhibited in thicker and non-staggered holes plate combinations.

Design and experimental validation of the inlet guide vane system of a mini hydraulic bulb-turbine

Energy Technology Data Exchange (ETDEWEB)

Ferro, L.M.C. [Department of Mechanical Engineering, Escola Superior de Tecnologia de Setubal, Polytechnic Institute of Setubal, Campus do IPS, Estefanilha, 2910-761 Setubal (Portugal); IDMEC, Instituto Superior Tecnico, Technical University of Lisbon, Av. Rovisco Pais,1049-001 Lisboa (Portugal); Gato, L.M.C.; Falcao, A.F.O. [IDMEC, Instituto Superior Tecnico, Technical University of Lisbon, Av. Rovisco Pais,1049-001 Lisboa (Portugal)

2010-09-15

The paper presents a fast design method for the inlet guide vanes of low-cost mini hydraulic bulb turbines. The guide vanes are positioned between two conical surfaces with a common vertex and have constant thickness distribution, except close to the leading and the trailing edges. The conical-walled inlet guide vane row is designed using a quasi-three-dimensional calculation method, by prescribing the angular-momentum distribution along the span at the outlet section of the guide vanes. The meridional through-flow is computed by a streamline curvature method and the blade-to-blade flow by a singularity surface method. The stagger angle and the vane camber are computed to fulfil the required design circulation and zero-incidence flow at the leading edge. The final vane shape is a single-curvature surface with straight leading and trailing edges. To validate the design method, a conical-walled inlet guide vane row nozzle-model with six fixed vanes was designed, manufactured and tested in an airflow rig. Traversing measurements along the circumferential and radial directions were made with a five-hole probe. The experimental results are compared with the prescribed design conditions and with numerical results from the three-dimensional inviscid and viscous flow computed with the FLUENT code. (author)

Computational design and experimental validation of new thermal barrier systems

Energy Technology Data Exchange (ETDEWEB)

Guo, Shengmin [Louisiana State Univ., Baton Rouge, LA (United States)

2015-03-31

The focus of this project is on the development of a reliable and efficient ab initio based computational high temperature material design method which can be used to assist the Thermal Barrier Coating (TBC) bond-coat and top-coat design. Experimental evaluations on the new TBCs are conducted to confirm the new TBCs’ properties. Southern University is the subcontractor on this project with a focus on the computational simulation method development. We have performed ab initio density functional theory (DFT) method and molecular dynamics simulation on screening the top coats and bond coats for gas turbine thermal barrier coating design and validation applications. For experimental validations, our focus is on the hot corrosion performance of different TBC systems. For example, for one of the top coatings studied, we examined the thermal stability of TaZr_2.75O₈ and confirmed it’s hot corrosion performance.

Quasi-experimental designs in practice-based research settings: design and implementation considerations.

Science.gov (United States)

Handley, Margaret A; Schillinger, Dean; Shiboski, Stephen

2011-01-01

Although randomized controlled trials are often a gold standard for determining intervention effects, in the area of practice-based research (PBR), there are many situations in which individual randomization is not possible. Alternative approaches to evaluating interventions have received increased attention, particularly those that can retain elements of randomization such that they can be considered "controlled" trials. Methodological design elements and practical implementation considerations for two quasi-experimental design approaches that have considerable promise in PBR settings--the stepped-wedge design, and a variant of this design, a wait-list cross-over design, are presented along with a case study from a recent PBR intervention for patients with diabetes. PBR-relevant design features include: creation of a cohort over time that collects control data but allows all participants (clusters or patients) to receive the intervention; staggered introduction of clusters; multiple data collection points; and one-way cross-over into the intervention arm. Practical considerations include: randomization versus stratification, training run in phases; and extended time period for overall study completion. Several design features of practice based research studies can be adapted to local circumstances yet retain elements to improve methodological rigor. Studies that utilize these methods, such as the stepped-wedge design and the wait-list cross-over design, can increase the evidence base for controlled studies conducted within the complex environment of PBR.

Factorial experimental design intended for the optimization of the alumina purification conditions

Science.gov (United States)

Brahmi, Mounaouer; Ba, Mohamedou; Hidri, Yassine; Hassen, Abdennaceur

2018-04-01

The objective of this study was to determine the optimal conditions by using the experimental design methodology for the removal of some impurities associated with the alumina. So, three alumina qualities of different origins were investigated under the same conditions. The application of full-factorial designs on the samples of different qualities of alumina has followed the removal rates of the sodium oxide. However, a factorial experimental design was developed to describe the elimination of sodium oxide associated with the alumina. The experimental results showed that chemical analyze followed by XRF prior treatment of the samples, provided a primary idea concerning these prevailing impurities. Therefore, it appeared that the sodium oxide constituted the largest amount among all impurities. After the application of experimental design, analysis of the effectors different factors and their interactions showed that to have a better result, we should reduce the alumina quantity investigated and by against increase the stirring time for the first two samples, whereas, it was necessary to increase the alumina quantity in the case of the third sample. To expand and improve this research, we should take into account all existing impurities, since we found during this investigation that the levels of partial impurities increased after the treatment.

Experimental Study on Various Solar Still Designs

OpenAIRE

T. Arunkumar; K. Vinothkumar; Amimul Ahsan; R. Jayaprakash; Sanjay Kumar

2012-01-01

Humankind has depended for ages on underground water reservoirs for its fresh water needs. But these sources do not always prove to be useful due to the presence of excessive salinity in the water. In this paper, the fabrication of seven solar still designs such as spherical solar still, pyramid solar still, hemispherical solar still, double basin glass solar still, concentrator coupled single slope solar still, tubular solar still and tubular solar still coupled with pyramid solar still and ...

Modelling and experimental validation for off-design performance of the helical heat exchanger with LMTD correction taken into account

Energy Technology Data Exchange (ETDEWEB)

Phu, Nguyen Minh; Trinh, Nguyen Thi Minh [Vietnam National University, Ho Chi Minh City (Viet Nam)

2016-07-15

Today the helical coil heat exchanger is being employed widely due to its dominant advantages. In this study, a mathematical model was established to predict off-design works of the helical heat exchanger. The model was based on the LMTD and e-NTU methods, where a LMTD correction factor was taken into account to increase accuracy. An experimental apparatus was set-up to validate the model. Results showed that errors of thermal duty, outlet hot fluid temperature, outlet cold fluid temperature, shell-side pressure drop, and tube-side pressure drop were respectively +-5%, +-1%, +-1%, +-5% and +-2%. Diagrams of dimensionless operating parameters and a regression function were also presented as design-maps, a fast calculator for usage in design and operation of the exchanger. The study is expected to be a good tool to estimate off-design conditions of the single-phase helical heat exchangers.

Effects of Singapore's Model Method on Elementary Student Problem Solving Performance: Single Subject Research

Science.gov (United States)

Mahoney, Kevin

2012-01-01

This research investigation examined the effects of Singapore's Model Method, also known as "model drawing" or "bar modeling" on the word problem-solving performance of American third and fourth grade students. Employing a single-case design, a researcher-designed teaching intervention was delivered to a child in third…

Overview of design development of FCC-hh Experimental Interaction Regions

CERN Document Server

AUTHOR|(CDS)2082479; Abelleira, Jose; Cruz Alaniz, Emilia; Van Riesen-Haupt, Leon; Benedikt, Michael; Besana, Maria Ilaria; Buffat, Xavier; Burkhardt, Helmut; Cerutti, Francesco; Langner, Andy Sven; Martin, Roman; Riegler, Werner; Schulte, Daniel; Tomas Garcia, Rogelio; Appleby, Robert Barrie; Rafique, Haroon; Barranco Garcia, Javier; Pieloni, Tatiana; Boscolo, Manuela; Collamati, Francesco; Nevay, Laurence James; Hofer, Michael

2017-01-01

The experimental interaction region (EIR) is one of the key areas that define the performance of the Future Circular Collider. In this overview we will describe the status and the evolution of the design of EIR of FCC-hh, focusing on design of the optics, energy deposition in EIR elements, beam-beam effects and machine detector interface issues.

Second preliminary design of JAERI experimental fusion reactor (JXFR)

International Nuclear Information System (INIS)

Sako, Kiyoshi; Tone, Tatsuzo; Seki, Yasushi; Iida, Hiromasa; Yamato, Harumi

1979-06-01

Second preliminary design of a tokamak experimental fusion reactor to be built in the near future has been performed. This design covers overall reactor system including plasma characteristics, reactor structure, blanket neutronics radiation shielding, superconducting magnets, neutral beam injector, electric power supply system, fuel recirculating system, reactor cooling and tritium recovery systems and maintenance scheme. Safety analyses of the reactor system have been also performed. This paper gives a brief description of the design as of January, 1979. The feasibility study of raising the power density has been also studied and is shown as appendix. (author)

Design of Water Temperature Control System Based on Single Chip Microcomputer

Science.gov (United States)

Tan, Hanhong; Yan, Qiyan

2017-12-01

In this paper, we mainly introduce a multi-function water temperature controller designed with 51 single-chip microcomputer. This controller has automatic and manual water, set the water temperature, real-time display of water and temperature and alarm function, and has a simple structure, high reliability, low cost. The current water temperature controller on the market basically use bimetal temperature control, temperature control accuracy is low, poor reliability, a single function. With the development of microelectronics technology, monolithic microprocessor function is increasing, the price is low, in all aspects of widely used. In the water temperature controller in the application of single-chip, with a simple design, high reliability, easy to expand the advantages of the function. Is based on the appeal background, so this paper focuses on the temperature controller in the intelligent control of the discussion.

GSK1265744 pharmacokinetics in plasma and tissue after single-dose long-acting injectable administration in healthy subjects.

Science.gov (United States)

Spreen, William; Ford, Susan L; Chen, Shuguang; Wilfret, David; Margolis, David; Gould, Elizabeth; Piscitelli, Stephen

2014-12-15

GSK1265744 (744) is an HIV-1 integrase inhibitor in clinical development as a long-acting (LA) injectable formulation. This study evaluated plasma and tissue pharmacokinetics after single-dose administration of 744 LA administered by intramuscular (IM) or subcutaneous injections. This was a phase I, open-label, 9-cohort, parallel study of 744 in healthy subjects. 744 was administered as a 200 mg/mL nanosuspension at doses of 100-800 mg IM and 100-400 mg subcutaneous. Eight (6 active and 2 placebo) male and female subjects participated in each of the first 7 cohorts. All 8 subjects, 4 males and 4 females, received active 744 LA in cohorts 8 and 9 and underwent rectal and cervicovaginal tissue sampling, respectively. Plasma pharmacokinetic sampling was performed for a minimum of 12 weeks or until 744 concentrations were ≤0.1 μg/mL. Rectal and cervicovaginal tissue biopsies were performed at weeks 2 and 8 (cohort 8) and weeks 4 and 12 (cohort 9). 744 LA was generally safe and well tolerated after single injections. A majority of subjects reported injection site reactions, all graded as mild in intensity. Plasma concentration-time profiles were prolonged with measureable concentrations up to 52 weeks after dosing. 744 LA 800 mg IM achieved mean concentrations above protein adjusted-IC90 for approximately 16 weeks. Rectal and cervicovaginal tissue concentrations ranged from injection has potential application as a monthly or less frequent HIV treatment or prevention agent.

Experimental Strength of Single-Lap Hybrid Joints on Woven Fabric Kenaf Fiber Composites Under Quasi Static Condition

Directory of Open Access Journals (Sweden)

Yee Lee Sim

2016-01-01

Full Text Available For the past decades, usage of natural fiber reinforced composites in low bearing load applications are increasing tremendously due to drawbacks concerning the use of synthetic fibers. Kenaf fibers have a good potential to be used as composite reinforcements as they possesses excellent fiber strength compared to own self-weight. Current work concentrates on mechanical properties of woven fabric kenaf composites with single-lap hybrid joints configurations. Four width to diameter ratio, (W/d of cross-ply lay-up joints as designed in testing series were tested by using quasi static mechanical testing. Experimental results showed that the failure load increased with the increasing of W/d ratios. Thinner lay-up had better bearing strength compared to thicker lay-up as found in current study.

Development of high quantum efficiency, flat panel, thick detectors for megavoltage x-ray imaging: An experimental study of a single-pixel prototype

International Nuclear Information System (INIS)

Mei, X.; Pang, G.

2005-01-01

Our overall goal is to develop a new generation of electronic portal imaging devices (EPIDs) with a quantum efficiency (QE) more than an order of magnitude higher and a spatial resolution equivalent to that of EPIDs currently used for portal imaging. A novel design of such a high QE flat-panel based EPID was introduced recently and its feasibility was investigated theoretically [see Pang and Rowlands, Med. Phys. 31, 3004 (2004)]. In this work, we constructed a prototype single-pixel detector based on the novel design. Some fundamental imaging properties including the QE, spatial resolution, and sensitivity of the prototype detector were measured with a 6 MV beam. It has been shown that the experimental results agree well with theoretical predictions and further development based on the novel design including the construction of a prototype area detector is warranted

Conceptual design study of Fusion Experimental Reactor (FY87FER)

International Nuclear Information System (INIS)

1988-05-01

The design study of Fusion Experimental Reactor(FER) which has been proposed to be the next step fusion device has been conducted by JAERI Reactor System Laboratory since 1982 and by FER design team since 1984. This is the final report of the FER design team program and describes the results obtained in FY1987 (partially in FY1986) activities. The contents of this report consist of the reference design which is based on the guideline in FY1986 by the Subcomitees set up in Nuclear Fusion Council of Atomic Energy Commission of Japan, the Low-Physics-Risk reactor design for achieving physics mission more reliably and the system study of FER design candidates including above two designs. (author)

Long-term functional, subjective and psychological results after single digit replantation.

Science.gov (United States)

Chen, Jing; Zhang, Ai Xian; Chen, Qing Zhong; Mu, Shuai; Tan, Jun

2018-03-01

The aim of this study was to analyse the long-term functional, subjective, and psychological results after single-digit replantation. Thirty cases of digital replantation (14 thumbs, 12 index fingers, 2 middle fingers, 1 ring finger, and 1 little finger) in 30 patients (7 females and 23 males) with a mean age of 44.2 years (20-65 years) were evaluated at the end of a mean follow-up time of 36 months (19-50 months). The active range of motion of joints, grip and pinch strength, cutaneous sensibility, upper-extremity functioning, and subjective satisfaction were determined using the Disability of Arm, Shoulder, and Hand (DASH) questionnaire and the Michigan Hand Outcomes questionnaire (MHQ). Psychological sequelae, including depression, anxiety, and posttraumatic stress disorder (PTSD), were assessed. A correlation analysis among variables was also performed. The mean score for the DASH questionnaire was 6.6 (range: 0-39.2). The symptom of cold intolerance occurred in 53% of the patients. Two patients were diagnosed with depression, and only one patient exhibited PTSD. The DASH score had a good statistical correlation with total grip strength, pinch grip strength, and static two-point discrimination (S-2PD) (P digit replantation are very low at long-term follow-up. Level IV, therapeutic study. Copyright © 2017 Turkish Association of Orthopaedics and Traumatology. Production and hosting by Elsevier B.V. All rights reserved.

First preliminary design of an experimental fusion reactor

International Nuclear Information System (INIS)

1977-09-01

A preliminary design of a tokamak experimental fusion reactor to be built in the near future is under way. The goals of the reactor are to achieve reactor-level plasma conditions for a sufficiently long operation period and to obtain design, construction and operational experience for the main components of full-scale power reactors. This design covers overall reactor system including plasma characteristics, reactor structure, blanket neutronics, shielding, superconducting magnets, neutral beam injector, electric power supply system, fuel circulating system, reactor cooling system, tritium recovery system and maintenance scheme. The main design parameters are as follows: the reactor fusion power 100 MW, torus radius 6.75 m, plasma radius 1.5 m, first wall radius 1.75 m, toroidal magnet field on axis 6 T, blanket fertile material Li 2 O, coolant He, structural material 316SS and tritium breeding ratio 0.9. (auth.)

Long-term functional, subjective and psychological results after single digit replantation

Directory of Open Access Journals (Sweden)

Jing Chen

2018-03-01

Full Text Available Objective: The aim of this study was to analyse the long-term functional, subjective, and psychological results after single-digit replantation. Methods: Thirty cases of digital replantation (14 thumbs, 12 index fingers, 2 middle fingers, 1 ring finger, and 1 little finger in 30 patients (7 females and 23 males with a mean age of 44.2 years (20–65 years were evaluated at the end of a mean follow-up time of 36 months (19–50 months. The active range of motion of joints, grip and pinch strength, cutaneous sensibility, upper-extremity functioning, and subjective satisfaction were determined using the Disability of Arm, Shoulder, and Hand (DASH questionnaire and the Michigan Hand Outcomes questionnaire (MHQ. Psychological sequelae, including depression, anxiety, and posttraumatic stress disorder (PTSD, were assessed. A correlation analysis among variables was also performed. Results: The mean score for the DASH questionnaire was 6.6 (range: 0–39.2. The symptom of cold intolerance occurred in 53% of the patients. Two patients were diagnosed with depression, and only one patient exhibited PTSD. The DASH score had a good statistical correlation with total grip strength, pinch grip strength, and static two-point discrimination (S-2PD (P < 0.05. Several aspects of the MHQ were also statistically relevant to some or all of the three objective results. Furthermore, the grip strength showed significant correlation with DASH and most aspects of the MHQ in multivariate logistic regression analysis (P < 0.05. Conclusion: Total grip strength is the most important factor positively related to subjective outcomes. The incidence rates of psychological symptoms after digit replantation are very low at long-term follow-up. Level of evidence: Level IV, therapeutic study. Keywords: Digit Replantation, DASH score, Posttraumatic stress disorder

Experimental control versus realism: methodological solutions for simulator studies in complex operating environments

Energy Technology Data Exchange (ETDEWEB)

Skraaning, Gyrd Jr.

2004-03-15

This report is a reprint of a dr.philos. thesis written by Gyrd Skraaning Jr. The text was submitted and accepted by the Norwegian University of Science and Technology in 2003 (ISBN 82-471-5237-1). The thesis suggests a nonlinear model of the theoretical relationship between experimental control and realism, claiming that high degrees of realism and experimental control can be obtained simultaneously if the experimental methods are utilized strategically and developed further. This is in opposition to the conventional opinion that realism and experimental control are mutually excluding objectives. The thesis debates the impact of the operating task on human performance during simulator studies in HAMMLAB, and suggests how task variation can be experimentally controlled. In a within subject design, every subject is tested under all experimental conditions, and the presentation order of the conditions is counterbalanced to compensate for order effects. In realistic settings, it is essential that the experimental design imposes few artificial constrains on the research environment. At the same time, the design should be able to uncover experimental effects in situations where the number of participants is low. Within-subject design represents a reasonable compromise between these aspirations. In this respect, an alternative counterbalancing method is proposed (dis-ORDER). A theoretical analysis of the human performance concept and a discussion about performance measurement in complex operating environments, are followed by a debate on the shortcomings of traditional performance indicators. Two specialized operator performance assessment techniques are then presented and evaluated (OPAS and ORT). (Author)

Experimental control versus realism: methodological solutions for simulator studies in complex operating environments

International Nuclear Information System (INIS)

Skraaning, Gyrd Jr.

2004-03-01

This report is a reprint of a dr.philos. thesis written by Gyrd Skraaning Jr. The text was submitted and accepted by the Norwegian University of Science and Technology in 2003 (ISBN 82-471-5237-1). The thesis suggests a nonlinear model of the theoretical relationship between experimental control and realism, claiming that high degrees of realism and experimental control can be obtained simultaneously if the experimental methods are utilized strategically and developed further. This is in opposition to the conventional opinion that realism and experimental control are mutually excluding objectives. The thesis debates the impact of the operating task on human performance during simulator studies in HAMMLAB, and suggests how task variation can be experimentally controlled. In a within subject design, every subject is tested under all experimental conditions, and the presentation order of the conditions is counterbalanced to compensate for order effects. In realistic settings, it is essential that the experimental design imposes few artificial constrains on the research environment. At the same time, the design should be able to uncover experimental effects in situations where the number of participants is low. Within-subject design represents a reasonable compromise between these aspirations. In this respect, an alternative counterbalancing method is proposed (dis-ORDER). A theoretical analysis of the human performance concept and a discussion about performance measurement in complex operating environments, are followed by a debate on the shortcomings of traditional performance indicators. Two specialized operator performance assessment techniques are then presented and evaluated (OPAS and ORT). (Author)

Design of a Facility for Studying Shock-Cell Noise on Single and Coaxial Jets

Directory of Open Access Journals (Sweden)

Daniel Guariglia

2018-03-01

Full Text Available Shock-cell noise occurs in aero-engines when the nozzle exhaust is supersonic and shock-cells are present in the jet. In commercial turbofan engines, at cruise, the secondary flow is often supersonic underexpanded, with the formation of annular shock-cells in the jet and consequent onset of shock-cell noise. This paper aims at describing the design process of the new facility FAST (Free jet AeroacouSTic laboratory at the von Karman Institute, aimed at the investigation of the shock-cell noise phenomenon on a dual stream jet. The rig consists of a coaxial open jet, with supersonic capability for both the primary and secondary flow. A coaxial silencer was designed to suppress the spurious noise coming from the feeding lines. Computational fluid dynamics (CFD simulations of the coaxial jet and acoustic simulations of the silencer have been carried out to support the design choices. Finally, the rig has been validated by performing experimental measurements on a supersonic single stream jet and comparing the results with the literature. Fine-scale PIV (Particle Image Velocimetry coupled with a microphone array in the far field have been used in this scope. Preliminary results of the dual stream jet are also shown.

Experimentally measuring a quantum state by the Heisenberg exchange interaction in a single apparatus

International Nuclear Information System (INIS)

Peng Xinhua; Du Jiangfeng; Suter, D.

2005-01-01

Full text: Quantum information processing requires the effective measurement of quantum states. An important method, called quantum state tomography, needs measuring a complete set of observables on the measured system to determine its unknown quantum state ρ. The measurement involves certain noncommuting observables as a result of Bohr's complementarity. Very recently, Allahverdyan et al. proposed a new method in which the unknown quantum state r is determined by measuring a set of commuting observables in the price of a controlled interaction with an auxiliary system. If both systems S and A are spins, their z components (σ z ) can be chosen to measure after some specific Heisenberg exchange interaction. We study in detail a general Heisenberg XYZ model for a two-qubit system and present two classes of special Heisenberg interactions which can serve as the controlled interaction in Allahverdyan's scheme when the state of the auxiliary system A is initially completely disordered. Using the nuclear magnetic resonance techniques, the measurement scheme in a single apparatus has been experimentally demonstrated by designing the quantum circuit to simulate the Heisenberg exchange interaction. (author)

Tau-U: A Quantitative Approach for Analysis of Single-Case Experimental Data in Aphasia.

Science.gov (United States)

Lee, Jaime B; Cherney, Leora R

2018-03-01

Tau-U is a quantitative approach for analyzing single-case experimental design (SCED) data. It combines nonoverlap between phases with intervention phase trend and can correct for a baseline trend (Parker, Vannest, & Davis, 2011). We demonstrate the utility of Tau-U by comparing it with the standardized mean difference approach (Busk & Serlin, 1992) that is widely reported within the aphasia SCED literature. Repeated writing measures from 3 participants with chronic aphasia who received computer-based writing treatment are analyzed visually and quantitatively using both Tau-U and the standardized mean difference approach. Visual analysis alone was insufficient for determining an effect between the intervention and writing improvement. The standardized mean difference yielded effect sizes ranging from 4.18 to 26.72 for trained items and 1.25 to 3.20 for untrained items. Tau-U yielded significant (p data from 2 of 3 participants. Tau-U has the unique advantage of allowing for the correction of an undesirable baseline trend. Although further study is needed, Tau-U shows promise as a quantitative approach to augment visual analysis of SCED data in aphasia.

Massively Parallel Single-Molecule Manipulation Using Centrifugal Force

Science.gov (United States)

Wong, Wesley; Halvorsen, Ken

2011-03-01

Precise manipulation of single molecules has led to remarkable insights in physics, chemistry, biology, and medicine. However, two issues that have impeded the widespread adoption of these techniques are equipment cost and the laborious nature of making measurements one molecule at a time. To meet these challenges, we have developed an approach that enables massively parallel single- molecule force measurements using centrifugal force. This approach is realized in the centrifuge force microscope, an instrument in which objects in an orbiting sample are subjected to a calibration-free, macroscopically uniform force- field while their micro-to-nanoscopic motions are observed. We demonstrate high- throughput single-molecule force spectroscopy with this technique by performing thousands of rupture experiments in parallel, characterizing force-dependent unbinding kinetics of an antibody-antigen pair in minutes rather than days. Currently, we are taking steps to integrate high-resolution detection, fluorescence, temperature control and a greater dynamic range in force. With significant benefits in efficiency, cost, simplicity, and versatility, single-molecule centrifugation has the potential to expand single-molecule experimentation to a wider range of researchers and experimental systems.

Design of JT-60SA magnets and associated experimental validations

International Nuclear Information System (INIS)

Zani, L.; Barabaschi, P.; Peyrot, M.; Meunier, L.; Tomarchio, V.; Duglue, D.; Decool, P.; Torre, A.; Marechal, J.L.; Della Corte, A.; Di Zenobio, A.; Muzzi, L.; Cucchiaro, A.; Turtu, S.; Ishida, S.; Yoshida, K.; Tsuchiya, K.; Kizu, K.; Murakami, H.

2011-01-01

In the framework of the JT-60SA project, aiming at upgrading the present JT-60U tokamak toward a fully superconducting configuration, the detailed design phase led to adopt for the three main magnet systems a brand new design. Europe (EU) is expected to provide to Japan (JA) the totality of the toroidal field (TF) magnet system, while JA will provide both Equilibrium field (EF) and Central Solenoid (CS) systems. All magnet designs were optimized trough the past years and entered in parallel into extensive experimentally-based phases of concept validation, which came to maturation in the years 2009 and 2010. For this, all magnet systems were investigated by mean of dedicated samples, e.g. conductor and joint samples designed, manufactured and tested at full scale in ad hoc facilities either in EU or in JA. The present paper, after an overall description of magnet systems layouts, presents in a general approach the different experimental campaigns dedicated to qualification design and manufacture processes of either coils, conductors and electrical joints. The main results with the associated analyses are shown and the main conclusions presented, especially regarding their contribution to consolidate the triggering of magnet mass production. The status of respective manufacturing stages in EU and in JA are also evoked. (authors)

Multi-objective experimental design for (13)C-based metabolic flux analysis.

Science.gov (United States)

Bouvin, Jeroen; Cajot, Simon; D'Huys, Pieter-Jan; Ampofo-Asiama, Jerry; Anné, Jozef; Van Impe, Jan; Geeraerd, Annemie; Bernaerts, Kristel

2015-10-01

(13)C-based metabolic flux analysis is an excellent technique to resolve fluxes in the central carbon metabolism but costs can be significant when using specialized tracers. This work presents a framework for cost-effective design of (13)C-tracer experiments, illustrated on two different networks. Linear and non-linear optimal input mixtures are computed for networks for Streptomyces lividans and a carcinoma cell line. If only glucose tracers are considered as labeled substrate for a carcinoma cell line or S. lividans, the best parameter estimation accuracy is obtained by mixtures containing high amounts of 1,2-(13)C2 glucose combined with uniformly labeled glucose. Experimental designs are evaluated based on a linear (D-criterion) and non-linear approach (S-criterion). Both approaches generate almost the same input mixture, however, the linear approach is favored due to its low computational effort. The high amount of 1,2-(13)C2 glucose in the optimal designs coincides with a high experimental cost, which is further enhanced when labeling is introduced in glutamine and aspartate tracers. Multi-objective optimization gives the possibility to assess experimental quality and cost at the same time and can reveal excellent compromise experiments. For example, the combination of 100% 1,2-(13)C2 glucose with 100% position one labeled glutamine and the combination of 100% 1,2-(13)C2 glucose with 100% uniformly labeled glutamine perform equally well for the carcinoma cell line, but the first mixture offers a decrease in cost of $ 120 per ml-scale cell culture experiment. We demonstrated the validity of a multi-objective linear approach to perform optimal experimental designs for the non-linear problem of (13)C-metabolic flux analysis. Tools and a workflow are provided to perform multi-objective design. The effortless calculation of the D-criterion can be exploited to perform high-throughput screening of possible (13)C-tracers, while the illustrated benefit of multi

Design and Experimental Investigation of Pneumatic Movement Mechanism Supported by Mechanic Cam and Crank Shaft

Directory of Open Access Journals (Sweden)

Salih KORUCU

2015-02-01

Full Text Available The pressurized air is applied to many sectors required purity and velocity. One of these sectors is to use of air as impulsive force in the moving mechanisms. In this study, the movement mechanism prototype worked with compressed air was designed and produced forlight vehicle engine as motorbike and ATV (All-Terrain Vehicle. In developed mechanisms, pneumatic artificial muscles were used for a given movement of crankshaft. A cam system was also designed for synchronization pneumatic muscles. In this way, these muscles transmit the synchronous movement to crankshaft. At the end of the study, the developed mechanism was mounted on an ATV vehicle(110 cc/ Cubic Centimeter, engine displacement capacityand its performance was tested using the four different weights (50, 75, 100 and 150 kg, three different pressures (4, 5 and 6 bar and two different hoses (Ø 6 and Ø 8 mm. By considering experimental results and design criteria, power of the movement mechanism was obtained as 886 Watt. With this study, minimization of energy consumption for movement of passenger cars, and using clean and cheap energy as ATV which can be alternative for single or two passenger vehicles.

Entropy-Based Experimental Design for Optimal Model Discrimination in the Geosciences

Directory of Open Access Journals (Sweden)

Wolfgang Nowak

2016-11-01

Full Text Available Choosing between competing models lies at the heart of scientific work, and is a frequent motivation for experimentation. Optimal experimental design (OD methods maximize the benefit of experiments towards a specified goal. We advance and demonstrate an OD approach to maximize the information gained towards model selection. We make use of so-called model choice indicators, which are random variables with an expected value equal to Bayesian model weights. Their uncertainty can be measured with Shannon entropy. Since the experimental data are still random variables in the planning phase of an experiment, we use mutual information (the expected reduction in Shannon entropy to quantify the information gained from a proposed experimental design. For implementation, we use the Preposterior Data Impact Assessor framework (PreDIA, because it is free of the lower-order approximations of mutual information often found in the geosciences. In comparison to other studies in statistics, our framework is not restricted to sequential design or to discrete-valued data, and it can handle measurement errors. As an application example, we optimize an experiment about the transport of contaminants in clay, featuring the problem of choosing between competing isotherms to describe sorption. We compare the results of optimizing towards maximum model discrimination with an alternative OD approach that minimizes the overall predictive uncertainty under model choice uncertainty.

Experimental and theoretical investigations of losses in a multifilament composite subjected

International Nuclear Information System (INIS)

Lefevre, F.; Turck, B.

1980-10-01

In a twisted multifilament composite subjected to transient axial fields three kinds of currents are induced: azimuthal currents in the matrix, azimuthal currents and coupling longitudinal currents in the filaments. Considering only the currents in the filament themselves, the hysteretic losses due to the azimuthal component Jsub(c) of the critical current density are usually the largest. However, when the coupling longitudinal currents flow in the outer layers of filaments in the same direction than the transport current their contribution become preponderant. Again, the theory shows three regimes depending only on the ratio of the amplitude of the changing field over a given threshold field, proportional to the twist pitch length of the composite. Experimental results clearly confirm the theory, in particular the increase of losses with transport current in a multifilament when only little effect was observed in a monofilament

Experimental determination of entanglement with a single measurement.

Science.gov (United States)

Walborn, S P; Souto Ribeiro, P H; Davidovich, L; Mintert, F; Buchleitner, A

2006-04-20

Nearly all protocols requiring shared quantum information--such as quantum teleportation or key distribution--rely on entanglement between distant parties. However, entanglement is difficult to characterize experimentally. All existing techniques for doing so, including entanglement witnesses or Bell inequalities, disclose the entanglement of some quantum states but fail for other states; therefore, they cannot provide satisfactory results in general. Such methods are fundamentally different from entanglement measures that, by definition, quantify the amount of entanglement in any state. However, these measures suffer from the severe disadvantage that they typically are not directly accessible in laboratory experiments. Here we report a linear optics experiment in which we directly observe a pure-state entanglement measure, namely concurrence. Our measurement set-up includes two copies of a quantum state: these 'twin' states are prepared in the polarization and momentum degrees of freedom of two photons, and concurrence is measured with a single, local measurement on just one of the photons.

ITER [International Thermonuclear Experimental Reactor] reactor building design study

International Nuclear Information System (INIS)

Thomson, S.L.; Blevins, J.D.; Delisle, M.W.

1989-01-01

The International Thermonuclear Experimental Reactor (ITER) is at the midpoint of a two-year conceptual design. The ITER reactor building is a reinforced concrete structure that houses the tokamak and associated equipment and systems and forms a barrier between the tokamak and the external environment. It provides radiation shielding and controls the release of radioactive materials to the environment during both routine operations and accidents. The building protects the tokamak from external events, such as earthquakes or aircraft strikes. The reactor building requirements have been developed from the component designs and the preliminary safety analysis. The equipment requirements, tritium confinement, and biological shielding have been studied. The building design in progress requires continuous iteraction with the component and system designs and with the safety analysis. 8 figs

Conceptual design study of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1986-11-01

Since 1980 the design study has been conducted at JAERI for the Fusion Experimental Reactor (FER) which has been proposed to be the next machine to JT-60 in the Japanese long term program of fusion reactor development. During two years from 1984 to 1985 FER concept was reviewed and redesigned. This report is the summary of the results obtained in the review and redesign activities in 1984 and 85. In the first year FER concept was discussed again and its frame work was reestablished. According to the new frame work the major reactor components of FER were designed. In the second year the whole plant system design including plant layout plan was conducted as well as the more detailed design analysis of the reactor conponents. The newly established frame for FER design is as follows: 1) Plasma : Self-ignition. 2) Operation scenario : Quasi-steady state operation with long burn pulse. 3) Neutron fluence on the first wall : 0.3 MWY/M 2 . 4) Blanket : Non-tritium breeding blanket with test modules for breeding blanket development. 5) Magnets : Superconducting Magnets. (author)

Displacement based seismic design of symmetric single-storey wood-frame buildings with the aid of N2 method

Directory of Open Access Journals (Sweden)

Panagiotis eMergos

2015-07-01

Full Text Available This paper presents a new methodology for the displacement-based seismic design of symmetric single-storey wood-frame buildings. Previous displacement-based design efforts were based on the direct displacement-based design (DDBD approach, which uses a substitute linear system with an appropriate stiffness and viscous damping combination. Despite the fact that this method has shown to produce promising results for wood structures, it does not fit into the framework of the Eurocode 8 (EC8 provisions. The methodology presented herein is based on the N2 method, which is incorporated in EC8 and combines the non-linear pushover analysis with the response spectrum method. The N2 method has been mostly applied to reinforced concrete and steel structures. In order to properly implement the N2 method for the case of wood-frame buildings new behavior factor – displacement ductility relationships are proposed. These relationships were derived from inelastic time history analyses of 35 SDOF systems subjected to 80 different ground motion records. Furthermore, the validity of the N2 method is examined for the case of a timber shear wall tested on a shake table and satisfactory predictions are obtained. Last, the proposed design methodology is applied to the displacement-based seismic design of a realistic symmetric single-storey wood-frame building in order to meet the performance objectives of EC8. It is concluded that the simplicity and computational efficiency of the adopted methodology make it a valuable tool for the seismic design of this category of wood-frame buildings, while the need for extending the method to more complex wood-frame buildings is also highlighted.

Measuring and Advancing Experimental Design Ability in an Introductory Course without Altering Existing Lab Curriculum

Directory of Open Access Journals (Sweden)

Ryan A. Shanks

2017-05-01

Full Text Available Introductory biology courses provide an important opportunity to prepare students for future courses, yet existing cookbook labs, although important in their own way, fail to provide many of the advantages of semester-long research experiences. Engaging, authentic research experiences aid biology students in meeting many learning goals. Therefore, overlaying a research experience onto the existing lab structure allows faculty to overcome barriers involving curricular change. Here we propose a working model for this overlay design in an introductory biology course and detail a means to conduct this lab with minimal increases in student and faculty workloads. Furthermore, we conducted exploratory factor analysis of the Experimental Design Ability Test (EDAT and uncovered two latent factors which provide valid means to assess this overlay model’s ability to increase advanced experimental design abilities. In a pre-test/post-test design, we demonstrate significant increases in both basic and advanced experimental design abilities in an experimental and comparison group. We measured significantly higher gains in advanced experimental design understanding in students in the experimental group. We believe this overlay model and EDAT factor analysis contribute a novel means to conduct and assess the effectiveness of authentic research experiences in an introductory course without major changes to the course curriculum and with minimal increases in faculty and student workloads.

The Subjective Sensation of Synchrony: An Experimental Study

KAUST Repository

Llobera, Joan; Charbonnier, Caecilia; Chagué , Sylvain; Preissmann, Delphine; Antonietti, Jean-Philippe; Ansermet, Franç ois; Magistretti, Pierre J.

2016-01-01

People performing actions together have a natural tendency to synchronize their behavior. Consistently, people doing a task together build internal representations not only of their actions and goals, but also of the other people performing the task. However, little is known about which are the behavioral mechanisms and the psychological factors affecting the subjective sensation of synchrony, or “connecting” with someone else. In this work, we sought to find which factors induce the subjective sensation of synchrony, combining motion capture data and psychological measures. Our results show that the subjective sensation of synchrony is affected by performance quality together with task category, and time. Psychological factors such as empathy and negative subjective affects also correlate with the subjective sensation of synchrony. However, when people estimate synchrony as seen from a third person perspective, their psychological factors do not affect the accuracy of the estimation. We suggest that to feel this sensation it is necessary to, first, have a good joint performance and, second, to assume the existence of an attention monitoring mechanism that reports that the attention of both participants (self and other) is focused on the task.

The Subjective Sensation of Synchrony: An Experimental Study

KAUST Repository

Llobera, Joan

2016-02-12

People performing actions together have a natural tendency to synchronize their behavior. Consistently, people doing a task together build internal representations not only of their actions and goals, but also of the other people performing the task. However, little is known about which are the behavioral mechanisms and the psychological factors affecting the subjective sensation of synchrony, or “connecting” with someone else. In this work, we sought to find which factors induce the subjective sensation of synchrony, combining motion capture data and psychological measures. Our results show that the subjective sensation of synchrony is affected by performance quality together with task category, and time. Psychological factors such as empathy and negative subjective affects also correlate with the subjective sensation of synchrony. However, when people estimate synchrony as seen from a third person perspective, their psychological factors do not affect the accuracy of the estimation. We suggest that to feel this sensation it is necessary to, first, have a good joint performance and, second, to assume the existence of an attention monitoring mechanism that reports that the attention of both participants (self and other) is focused on the task.

Designing Infographics to support teaching complex science subject: A comparison between static and animated Infographics

Science.gov (United States)

Hassan, Hesham Galal

This thesis explores the proper principles and rules for creating excellent infographics that communicate information successfully and effectively. Not only does this thesis examine the creation of Infographics, it also tries to answer which format, Static or Animated Infographics, is the most effective when used as a teaching-aid framework for complex science subjects, and if compelling Infographics in the preferred format facilitate the learning experience. The methodology includes the creation of infographic using two formats (Static and Animated) of a fairly complex science subject (Phases Of The Moon), which were then tested for their efficacy as a whole, and the two formats were compared in terms of information comprehension and retention. My hypothesis predicts that the creation of an infographic using the animated format would be more effective in communicating a complex science subject (Phases Of The Moon), specifically when using 3D computer animation to visualize the topic. This would also help different types of learners to easily comprehend science subjects. Most of the animated infographics produced nowadays are created for marketing and business purposes and do not implement the analytical design principles required for creating excellent information design. I believe that science learners are still in need of more variety in their methods of learning information, and that infographics can be of great assistance. The results of this thesis study suggests that using properly designed infographics would be of great help in teaching complex science subjects that involve spatial and temporal data. This could facilitate learning science subjects and consequently impact the interest of young learners in STEM.

Pharmacokinetics of colistin methanesulfonate (CMS) in healthy Chinese subjects after single and multiple intravenous doses.

Science.gov (United States)

Zhao, Miao; Wu, Xiao-Jie; Fan, Ya-Xin; Zhang, Ying-Yuan; Guo, Bei-Ning; Yu, Ji-Cheng; Cao, Guo-Ying; Chen, Yuan-Cheng; Wu, Ju-Fang; Shi, Yao-Guo; Li, Jian; Zhang, Jing

2018-05-01

The high prevalence of extensively drug-resistant Gram-negative pathogens has forced clinicians to use colistin as a last-line therapy. Knowledge on the pharmacokinetics of colistin methanesulfonate (CMS), an inactive prodrug, and colistin has increased substantially; however, the pharmacokinetics in the Chinese population is still unknown due to lack of a CMS product in China. This study aimed to evaluate the pharmacokinetics of a new CMS product developed in China in order to optimise dosing regimens. A total of 24 healthy subjects (12 female, 12 male) were enrolled in single- and multiple-dose pharmacokinetic (PK) studies. Concentrations of CMS and formed colistin in plasma and urine were measured, and PK analysis was conducted using a non-compartmental approach. Following a single CMS dose [2.36 mg colistin base activity (CBA) per kg, 1 h infusion], peak concentrations (C max ) of CMS and formed colistin were 18.0 mg/L and 0.661 mg/L, respectively. The estimated half-life (t 1/2 ) of CMS and colistin were 1.38 h and 4.49 h, respectively. Approximately 62.5% of the CMS dose was excreted via urine within 24 h after dosing, whilst only 1.28% was present in the form of colistin. Following multiple CMS doses, colistin reached steady-state within 24 h; there was no accumulation of CMS, but colistin accumulated slightly (R AUC  = 1.33). This study provides the first PK data in the Chinese population and is essential for designing CMS dosing regimens for use in Chinese hospitals. The urinary PK data strongly support the use of intravenous CMS for serious urinary tract infections. Copyright © 2018 Elsevier B.V. and International Society of Chemotherapy. All rights reserved.

Experimental Investigation of Subject-Specific On-Body Radio Propagation Channels for Body-Centric Wireless Communications

Directory of Open Access Journals (Sweden)

Mohammad Monirujjaman Khan

2014-01-01

Full Text Available In this paper, subject-specific narrowband (2.45 GHz and ultra-wideband (3–10.6 GHz on-body radio propagation studies in wireless body area networks (WBANs were performed by characterizing the path loss for eight different human subjects of different shapes and sizes. The body shapes and sizes of the test subjects used in this study are characterised as thin, medium build, fatty, shorter, average height and taller. Experimental investigation was made in an indoor environment using a pair of printed monopoles (for the narrowband case and a pair of tapered slot antennas (for the ultra-wideband (UWB case. Results demonstrated that, due to the different sizes, heights and shapes of the test subjects, the path loss exponent value varies up to maximum of 0.85 for the narrowband on-body case, whereas a maximum variation of the path loss exponent value of 1.15 is noticed for the UWB case. In addition, the subject-specific behaviour of the on-body radio propagation channels was compared between narrowband and UWB systems, and it was deduced that the on-body radio channels are subject-specific for both narrowband and UWB system cases, when the same antennas (same characteristics are used. The effect of the human body shape and size variations on the eight different on-body radio channels is also studied for both the narrowband and UWB cases.

Experimental Behavior of Fatigued Single Stiffener PRSEUS Specimens

Science.gov (United States)

Jegley, Dawn C.

2009-01-01

NASA, the Air Force Research Laboratory and The Boeing Company have worked to develop new low-cost, light-weight composite structures for aircraft. A Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept has been developed which offers advantages over traditional metallic structure. In this concept a stitched carbon-epoxy material system has been developed with the potential for reducing the weight and cost of transport aircraft structure by eliminating fasteners, thereby reducing part count and labor. By adding unidirectional carbon rods to the top of stiffeners, the panel becomes more structurally efficient. This combination produces a more damage tolerant design. This document describes the results of experimentation on PRSEUS specimens loaded in unidirectional compression in fatigue and to failure.

Design and experimental study of a solar system for heating water ...

African Journals Online (AJOL)

This work presents a design and an experimental study of a linear Fresnel reflector solar with trapezoidal cavity. This prototype is used for heating the tap water. The reflector was designed, constructed and tested in mechanical engineering department, University of Blida 1, Algeria. Various combinations of reflecting mirrors ...

Mechanical design and first experimental results of an upgraded technical PERMCAT reactor for tritium recovery in the fuel cycle of a fusion machine

Energy Technology Data Exchange (ETDEWEB)

Welte, S., E-mail: stefan.welte@kit.edu [Karlsruhe Institute of Technology (KIT), Forschungszentrum Karlsruhe, Institute for Technical Physics, Tritium Laboratory Karlsruhe, Hermann v. Helmholtz Platz 1, 76344 Eggenstein Leopoldshafen (Germany); Demange, D.; Wagner, R. [Karlsruhe Institute of Technology (KIT), Forschungszentrum Karlsruhe, Institute for Technical Physics, Tritium Laboratory Karlsruhe, Hermann v. Helmholtz Platz 1, 76344 Eggenstein Leopoldshafen (Germany)

2010-12-15

The PERMCAT process developed for the final clean-up stage of the Tokamak Exhaust Processing systems of the ITER tritium plant combines a catalytic reactor and a Pd/Ag permeator in a single component. A first generation technical PERMCAT has been successfully operated as part of the CAPER experiment at the Tritium Laboratory Karlsruhe for several years. Various alternative PERMCAT mechanical designs were proposed and studied on small-scale prototypes. An upgraded technical PERMCAT reactor was designed, manufactured and commissioned with deuterium. A parallel arrangement of finger-type membranes inserted in a single catalyst bed design was chosen to simplify the geometry and the manufacturing while improving the robustness of the reactor. The component has been designed and manufactured to be fully tritium compatible and also fully compatible with both process and electrical connections of the previous PERMCAT to be replaced. The new PERMCAT mechanical design is more compact and easy to manufacture. This PERMCAT reactor was submitted to functional tests and experiments based on isotopic exchanges between H{sub 2}O and D{sub 2} to measure the processing performances. The first experimental results show decontamination factors versus flow rates better than all previously measured.

Mechanical design and first experimental results of an upgraded technical PERMCAT reactor for tritium recovery in the fuel cycle of a fusion machine

International Nuclear Information System (INIS)

Welte, S.; Demange, D.; Wagner, R.

2010-01-01

The PERMCAT process developed for the final clean-up stage of the Tokamak Exhaust Processing systems of the ITER tritium plant combines a catalytic reactor and a Pd/Ag permeator in a single component. A first generation technical PERMCAT has been successfully operated as part of the CAPER experiment at the Tritium Laboratory Karlsruhe for several years. Various alternative PERMCAT mechanical designs were proposed and studied on small-scale prototypes. An upgraded technical PERMCAT reactor was designed, manufactured and commissioned with deuterium. A parallel arrangement of finger-type membranes inserted in a single catalyst bed design was chosen to simplify the geometry and the manufacturing while improving the robustness of the reactor. The component has been designed and manufactured to be fully tritium compatible and also fully compatible with both process and electrical connections of the previous PERMCAT to be replaced. The new PERMCAT mechanical design is more compact and easy to manufacture. This PERMCAT reactor was submitted to functional tests and experiments based on isotopic exchanges between H 2 O and D 2 to measure the processing performances. The first experimental results show decontamination factors versus flow rates better than all previously measured.

Symposium on single cell analysis and genomic approaches, Experimental Biology 2017 Chicago, Illinois, April 23, 2017.

Science.gov (United States)

Coller, Hilary A

2017-09-01

Emerging technologies for the analysis of genome-wide information in single cells have the potential to transform many fields of biology, including our understanding of cell states, the response of cells to external stimuli, mosaicism, and intratumor heterogeneity. At Experimental Biology 2017 in Chicago, Physiological Genomics hosted a symposium in which five leaders in the field of single cell genomics presented their recent research. The speakers discussed emerging methodologies in single cell analysis and critical issues for the analysis of single cell data. Also discussed were applications of single cell genomics to understanding the different types of cells within an organism or tissue and the basis for cell-to-cell variability in response to stimuli. Copyright © 2017 the American Physiological Society.

A Framework for Control System Design Subject to Average Data-Rate Constraints

DEFF Research Database (Denmark)

Silva, Eduardo; Derpich, Milan; Østergaard, Jan

2011-01-01

This paper studies discrete-time control systems subject to average data-rate limits. We focus on a situation where a noisy linear system has been designed assuming transparent feedback and, due to implementation constraints, a source-coding scheme (with unity signal transfer function) has to be ...

Fast estimation of expected information gains for Bayesian experimental designs based on Laplace approximations

KAUST Repository

Long, Quan; Scavino, Marco; Tempone, Raul; Wang, Suojin

2013-01-01

Shannon-type expected information gain can be used to evaluate the relevance of a proposed experiment subjected to uncertainty. The estimation of such gain, however, relies on a double-loop integration. Moreover, its numerical integration in multi-dimensional cases, e.g., when using Monte Carlo sampling methods, is therefore computationally too expensive for realistic physical models, especially for those involving the solution of partial differential equations. In this work, we present a new methodology, based on the Laplace approximation for the integration of the posterior probability density function (pdf), to accelerate the estimation of the expected information gains in the model parameters and predictive quantities of interest. We obtain a closed-form approximation of the inner integral and the corresponding dominant error term in the cases where parameters are determined by the experiment, such that only a single-loop integration is needed to carry out the estimation of the expected information gain. To deal with the issue of dimensionality in a complex problem, we use a sparse quadrature for the integration over the prior pdf. We demonstrate the accuracy, efficiency and robustness of the proposed method via several nonlinear numerical examples, including the designs of the scalar parameter in a one-dimensional cubic polynomial function, the design of the same scalar in a modified function with two indistinguishable parameters, the resolution width and measurement time for a blurred single peak spectrum, and the boundary source locations for impedance tomography in a square domain. © 2013 Elsevier B.V.

Fast estimation of expected information gains for Bayesian experimental designs based on Laplace approximations

KAUST Repository

Long, Quan

2013-06-01

Shannon-type expected information gain can be used to evaluate the relevance of a proposed experiment subjected to uncertainty. The estimation of such gain, however, relies on a double-loop integration. Moreover, its numerical integration in multi-dimensional cases, e.g., when using Monte Carlo sampling methods, is therefore computationally too expensive for realistic physical models, especially for those involving the solution of partial differential equations. In this work, we present a new methodology, based on the Laplace approximation for the integration of the posterior probability density function (pdf), to accelerate the estimation of the expected information gains in the model parameters and predictive quantities of interest. We obtain a closed-form approximation of the inner integral and the corresponding dominant error term in the cases where parameters are determined by the experiment, such that only a single-loop integration is needed to carry out the estimation of the expected information gain. To deal with the issue of dimensionality in a complex problem, we use a sparse quadrature for the integration over the prior pdf. We demonstrate the accuracy, efficiency and robustness of the proposed method via several nonlinear numerical examples, including the designs of the scalar parameter in a one-dimensional cubic polynomial function, the design of the same scalar in a modified function with two indistinguishable parameters, the resolution width and measurement time for a blurred single peak spectrum, and the boundary source locations for impedance tomography in a square domain. © 2013 Elsevier B.V.

TIBER: Tokamak Ignition/Burn Experimental Research. Final design report

International Nuclear Information System (INIS)

Henning, C.D.; Logan, B.G.; Barr, W.L.

1985-01-01

The Tokamak Ignition/Burn Experimental Research (TIBER) device is the smallest superconductivity tokamak designed to date. In the design plasma shaping is used to achieve a high plasma beta. Neutron shielding is minimized to achieve the desired small device size, but the superconducting magnets must be shielded sufficiently to reduce the neutron heat load and the gamma-ray dose to various components of the device. Specifications of the plasma-shaping coil, the shielding, coaling, requirements, and heating modes are given. 61 refs., 92 figs., 30 tabs

Motion Correction of Single-Voxel Spectroscopy by Independent Component Analysis Applied to Spectra From Nonanesthetized Pediatric Subjects

DEFF Research Database (Denmark)

de Nijs, Robin; Miranda, Maria J.; Hansen, Lars Kai

2009-01-01

For single-voxel spectroscopy, the acquisition of the spectrum is typically repeated n times and then combined with a factor in order to improve the signal-to-noise ratio. In practice, the acquisitions are not only affected by random noise but also by physiologic motion and subject movements. Since...... the influence of physiologic motion such as cardiac and respiratory motion on the data is limited, it can be compensated for without data loss. Individual acquisitions hampered by subject movements, on the other hand, need to be rejected if no correction or compensation is possible. If the individual...

Computer experimental analysis of the CHP performance of a 100 kW e SOFC Field Unit by a factorial design

Science.gov (United States)

Calì, M.; Santarelli, M. G. L.; Leone, P.

Gas Turbine Technologies (GTT) and Politecnico di Torino, both located in Torino (Italy), have been involved in the design and installation of a SOFC laboratory in order to analyse the operation, in cogenerative configuration, of the CHP 100 kW e SOFC Field Unit, built by Siemens-Westinghouse Power Corporation (SWPC), which is at present (May 2005) starting its operation and which will supply electric and thermal power to the GTT factory. In order to take the better advantage from the analysis of the on-site operation, and especially to correctly design the scheduled experimental tests on the system, we developed a mathematical model and run a simulated experimental campaign, applying a rigorous statistical approach to the analysis of the results. The aim of this work is the computer experimental analysis, through a statistical methodology (2 k factorial experiments), of the CHP 100 performance. First, the mathematical model has been calibrated with the results acquired during the first CHP100 demonstration at EDB/ELSAM in Westerwoort. After, the simulated tests have been performed in the form of computer experimental session, and the measurement uncertainties have been simulated with perturbation imposed to the model independent variables. The statistical methodology used for the computer experimental analysis is the factorial design (Yates' Technique): using the ANOVA technique the effect of the main independent variables (air utilization factor U ox, fuel utilization factor U F, internal fuel and air preheating and anodic recycling flow rate) has been investigated in a rigorous manner. Analysis accounts for the effects of parameters on stack electric power, thermal recovered power, single cell voltage, cell operative temperature, consumed fuel flow and steam to carbon ratio. Each main effect and interaction effect of parameters is shown with particular attention on generated electric power and stack heat recovered.

Pharmacokinetics, Safety and Tolerability of Sacubitril/Valsartan (LCZ696) After Single-Dose Administration in Healthy Chinese Subjects.

Science.gov (United States)

Han, Yi; Ayalasomayajula, Surya; Pan, Wei; Yang, Fan; Yuan, Yaozong; Langenickel, Thomas; Hinder, Markus; Kalluri, Sampath; Pal, Parasar; Sunkara, Gangadhar

2017-02-01

Sacubitril/valsartan (LCZ696) is a first-in-class angiotensin receptor neprilysin inhibitor (ARNI) and has been recently approved in several countries for the treatment of patients with heart failure and reduced ejection fraction. This was the first study conducted to characterise the pharmacokinetics of LCZ696 analytes (pro-drug sacubitril, active neprilysin inhibitor LBQ657 and valsartan) after single-dose administration of LCZ696 in healthy Chinese subjects. In this open-label, randomised, parallel-group study, following screening and baseline evaluation, eligible healthy subjects received single oral doses of LCZ696 50, 100, 200 or 400 mg. The pharmacokinetics, safety and tolerability of LCZ696 were assessed up to 72 h after dosing. A total of 40 healthy male subjects were enrolled, and all completed the study. Following oral administration, LCZ696 delivered systemic exposure to sacubitril, LBQ657 and valsartan with a median time to reach maximum plasma concentration (T max ) ranging from 0.50 to 1.25, 2.00 to 3.00 and 1.50 to 2.50 h, respectively, over the investigated dose range. The mean terminal elimination half-life (T 1/2 ) ranged from 0.89 to 1.35, 8.57 to 9.24 and 5.33 to 7.91 h for sacubitril, LBQ657 and valsartan, respectively. The area under the plasma concentration-time curve from time zero to the time of the last quantifiable concentration (AUC 0-last ), and maximum plasma concentration (C max ) for LBQ657 increased dose proportionally over the entire dose range. Dose linear increase in the exposure was observed across the dose range for sacubitril and valsartan. LCZ696 was safe and well tolerated at all doses in this study. Adverse events of only mild intensity, which required no treatment, were reported in 6 (15 %) subjects. The pharmacokinetic profiles of LCZ696 analytes in Chinese subjects are similar to those reported previously in Caucasian subjects.

Design and experimental results of the 1-T Bitter Electromagnet Testing Apparatus (BETA)

Science.gov (United States)

Bates, E. M.; Birmingham, W. J.; Romero-Talamás, C. A.

2018-05-01

The Bitter Electromagnet Testing Apparatus (BETA) is a 1-Tesla (T) technical prototype of the 10 T Adjustable Long Pulsed High-Field Apparatus. BETA's final design specifications are highlighted in this paper which include electromagnetic, thermal, and stress analyses. We discuss here the design and fabrication of BETA's core, vessel, cooling, and electrical subsystems. The electrical system of BETA is composed of a scalable solid-state DC breaker circuit. Experimental results display the stable operation of BETA at 1 T. These results are compared to both analytical design and finite element calculations. Experimental results validate analytical magnet designing methods developed at the Dusty Plasma Laboratory. The theoretical steady state maxima and the limits of BETA's design are explored in this paper.

Single pressure vessel (SPV) nickel-hydrogen battery design

Energy Technology Data Exchange (ETDEWEB)

Coates, D.; Grindstaff, B.; Fox, C. [Eagle-Picher Industries, Inc., Joplin, MO (United States)

1995-07-01

Single pressure vessel (SPV) technology combines an entire multi-cell nickel-hydrogen (NiH{sub 2}) space battery within a single pressure vessel. SPV technology has been developed to improve the performance (volume/mass) of the NiH{sub 2} system at the battery level and ultimately to reduce overall battery cost and increase system reliability. Three distinct SPV technologies are currently under development and in production. Eagle-Picher has license to the COMSAT Laboratories technology, as well as internally developed independent SPV technology. A third technology resulted from the acquisition of Johnson Controls NiH{sub 2} battery assets in June, 1994. SPV batteries are currently being produced in 25 ampere-hour (Ah), 35 Ah and 50 Ah configurations. The battery designs have an overall outside diameter of 10 inches (25.4 centimeters).

Design and Implementation of an Enhanced 802.11 MAC Architecture for Single-Hop Wireless Networks

Directory of Open Access Journals (Sweden)

Ralph Bernasconi

2007-01-01

Full Text Available Due to its extreme simplicity and flexibility, the IEEE 802.11 standard is the dominant technology to implement both infrastructure-based WLANs and single-hop ad hoc networks. In spite of its popularity, there is a vast literature demonstrating the shortcomings of using the 802.11 technology in such environments, such as dramatic degradation of network capacity as contention increases and vulnerability to external interferences. Therefore, the design of enhancements and optimizations for the original 802.11 MAC protocol has been a very active research area in the last years. However, all these modifications to the 802.11 MAC protocol were validated only through simulations and/or analytical investigations. In this paper, we present a very unique work as we have designed a flexible hardware/software platform, fully compatible with current implementations of the IEEE 802.11 technology, which we have used to concretely implement and test an enhanced 802.11 backoff algorithm. Our experimental results clearly show that the enhanced mechanism outperforms the standard 802.11 MAC protocol in real scenarios.

Validation of a buffet meal design in an experimental restaurant.

Science.gov (United States)

Allirot, Xavier; Saulais, Laure; Disse, Emmanuel; Roth, Hubert; Cazal, Camille; Laville, Martine

2012-06-01

We assessed the reproducibility of intakes and meal mechanics parameters (cumulative energy intake (CEI), number of bites, bite rate, mean energy content per bite) during a buffet meal designed in a natural setting, and their sensitivity to food deprivation. Fourteen men were invited to three lunch sessions in an experimental restaurant. Subjects ate their regular breakfast before sessions A and B. They skipped breakfast before session FAST. The same ad libitum buffet was offered each time. Energy intakes and meal mechanics were assessed by foods weighing and video recording. Intrasubject reproducibility was evaluated by determining intraclass correlation coefficients (ICC). Mixed-models were used to assess the effects of the sessions on CEI. We found a good reproducibility between A and B for total energy (ICC=0.82), carbohydrate (ICC=0.83), lipid (ICC=0.81) and protein intake (ICC=0.79) and for meal mechanics parameters. Total energy, lipid and carbohydrate intake were higher in FAST than in A and B. CEI were found sensitive to differences in hunger level while the other meal mechanics parameters were stable between sessions. In conclusion, a buffet meal in a normal eating environment is a valid tool for assessing the effects of interventions on intakes. Copyright © 2012 Elsevier Ltd. All rights reserved.

Design study of blanket structure for tokamak experimental fusion reactor

International Nuclear Information System (INIS)

1979-11-01

Design study of the blanket structure for JAERI Experimental Fusion Reactor (JXFR) has been carried out. Studied here were fabrication and testing of the blanket structure (blanket cells, blanket rings, piping and blanket modules), assembly and disassembly of the blanket module, and monitering and testing technique. Problems in design and fabrication of the blanket structure could be revealed. Research and development problems for the future were also disclosed. (author)

Experimental study of single-electron loss by Ar{sup +} ions in rare-gas atoms

Energy Technology Data Exchange (ETDEWEB)

Reyes, P.G. [Facultad de Ciencias, UNAM, Coyoacan (Mexico); Castillo, F. [Instituto de Ciencias Nucleares, UNAM, Coyoacan (Mexico); Martinez, H. [Centro de Ciencias Fisicas, UNAM, Cuernavaca, Morelos (Mexico)]. E-mail: hm@fis.unam.mx

2001-04-28

Absolute differential and total cross sections for single-electron loss were measured for Ar{sup +} ions on rare-gas atoms in the laboratory energy range of 1.5 to 5.0 keV. The electron loss cross sections for all the targets studied are found to be in the order of magnitude between 10{sup -19} and 10{sup -22} cm{sup 2}, and show a monotonically increasing behaviour as a function of the incident energy. The behaviour of the total single-electron loss cross sections with the atomic target number, Z{sub t}, shows different dependences as the collision energy increases. In all cases the present results display experimental evidence of saturation in the single-electron loss cross section as the atomic number of the target increases. (author)

Computing tools for implementing standards for single-case designs.

Science.gov (United States)

Chen, Li-Ting; Peng, Chao-Ying Joanne; Chen, Ming-E

2015-11-01

In the single-case design (SCD) literature, five sets of standards have been formulated and distinguished: design standards, assessment standards, analysis standards, reporting standards, and research synthesis standards. This article reviews computing tools that can assist researchers and practitioners in meeting the analysis standards recommended by the What Works Clearinghouse: Procedures and Standards Handbook-the WWC standards. These tools consist of specialized web-based calculators or downloadable software for SCD data, and algorithms or programs written in Excel, SAS procedures, SPSS commands/Macros, or the R programming language. We aligned these tools with the WWC standards and evaluated them for accuracy and treatment of missing data, using two published data sets. All tools were tested to be accurate. When missing data were present, most tools either gave an error message or conducted analysis based on the available data. Only one program used a single imputation method. This article concludes with suggestions for an inclusive computing tool or environment, additional research on the treatment of missing data, and reasonable and flexible interpretations of the WWC standards. © The Author(s) 2015.

Efficient Bayesian experimental design for contaminant source identification

Science.gov (United States)

Zhang, Jiangjiang; Zeng, Lingzao; Chen, Cheng; Chen, Dingjiang; Wu, Laosheng

2015-01-01

In this study, an efficient full Bayesian approach is developed for the optimal sampling well location design and source parameters identification of groundwater contaminants. An information measure, i.e., the relative entropy, is employed to quantify the information gain from concentration measurements in identifying unknown parameters. In this approach, the sampling locations that give the maximum expected relative entropy are selected as the optimal design. After the sampling locations are determined, a Bayesian approach based on Markov Chain Monte Carlo (MCMC) is used to estimate unknown parameters. In both the design and estimation, the contaminant transport equation is required to be solved many times to evaluate the likelihood. To reduce the computational burden, an interpolation method based on the adaptive sparse grid is utilized to construct a surrogate for the contaminant transport equation. The approximated likelihood can be evaluated directly from the surrogate, which greatly accelerates the design and estimation process. The accuracy and efficiency of our approach are demonstrated through numerical case studies. It is shown that the methods can be used to assist in both single sampling location and monitoring network design for contaminant source identifications in groundwater.

Hysterectomy and Bilateral Salpingoovariectomy in a Transsexual Subject without Visible Scaring

OpenAIRE

Perrone, Anna Myriam; Scifo, Maria Cristina; Martelli, Valentina; Casadio, Paolo; Morselli, Paolo Giovanni; Pelusi, Giuseppe; Meriggiola, Maria Cristina

2010-01-01

Objective. To report on the use of laparoendoscopic single-site surgery (LESS) for the management of total hysterectomy (TH) with bilateral salpingoovariectomy (BSO) in a subject affected by gender identity disorder. Design. Case report. Setting. University Hospital. Patient(s). A 27-year-old affected by Gender Identity Disorder underwent a hysterectomy and BSO as part of surgical sex reassignment. Intervention(s). Laparoendoscopic single-site surgery access for TH and BSO. Main Outcome ...

Experimental Results for Direction of Arrival Estimation with a Single Acoustic Vector Sensor in Shallow Water

Directory of Open Access Journals (Sweden)

Alper Bereketli

2015-01-01

Full Text Available We study the performances of several computationally efficient and simple techniques for estimating direction of arrival (DOA of an underwater acoustic source using a single acoustic vector sensor (AVS in shallow water. Underwater AVS is a compact device, which consists of one hydrophone and three accelerometers in a packaged form, measuring scalar pressure and three-dimensional acceleration simultaneously at a single position. A very controlled experimental setup is prepared to test how well-known techniques, namely, arctan-based, intensity-based, time domain beamforming, and frequency domain beamforming methods, perform in estimating DOA of a source in different circumstances. Experimental results reveal that for almost all cases beamforming techniques perform best. Moreover, arctan-based method, which is the simplest of all, provides satisfactory results for practical purposes.

Enhancing the hermeneutic single-case efficacy design: Bridging the research-practice gap.

Science.gov (United States)

Wall, Jessie M; Kwee, Janelle L; Hu, Monica; McDonald, Marvin J

2017-09-01

Systematic case study designs are emerging as alternative paradigm strategies for psychotherapy and social science research. Through enhanced sensitivity to context, these designs examine idiographic profiles of causal processes. We specifically advocate the use of the hermeneutic single-case efficacy design (HSCED). HSCED has recently been used to investigate the efficacy of an existing therapy with a new population (Observed and Experiential Integration for athlete performance barriers) and an emerging therapy (Lifespan Integration Therapy). We describe innovations in HSCED that were implemented for these studies. These developments include (a) integrating psychotherapists as case developers, (b) incorporating multiple cases in one investigation, and (c) tailoring the repertoire of assessment tools. These extensions strategically incorporated principles of contextual paradigms in HSCED, thus complementing single-case designs that neglect idiographic contexts. We discuss recommendations for using HSCED in practice-based research, highlighting its potential as a bridge to address the research-practice gap.

No auditory experience, no tinnitus: Lessons from subjects with congenital- and acquired single-sided deafness.

Science.gov (United States)

Lee, Sang-Yeon; Nam, Dong Woo; Koo, Ja-Won; De Ridder, Dirk; Vanneste, Sven; Song, Jae-Jin

2017-10-01

Recent studies have adopted the Bayesian brain model to explain the generation of tinnitus in subjects with auditory deafferentation. That is, as the human brain works in a Bayesian manner to reduce environmental uncertainty, missing auditory information due to hearing loss may cause auditory phantom percepts, i.e., tinnitus. This type of deafferentation-induced auditory phantom percept should be preceded by auditory experience because the fill-in phenomenon, namely tinnitus, is based upon auditory prediction and the resultant prediction error. For example, a recent animal study observed the absence of tinnitus in cats with congenital single-sided deafness (SSD; Eggermont and Kral, Hear Res 2016). However, no human studies have investigated the presence and characteristics of tinnitus in subjects with congenital SSD. Thus, the present study sought to reveal differences in the generation of tinnitus between subjects with congenital SSD and those with acquired SSD to evaluate the replicability of previous animal studies. This study enrolled 20 subjects with congenital SSD and 44 subjects with acquired SSD and examined the presence and characteristics of tinnitus in the groups. None of the 20 subjects with congenital SSD perceived tinnitus on the affected side, whereas 30 of 44 subjects with acquired SSD experienced tinnitus on the affected side. Additionally, there were significant positive correlations between tinnitus characteristics and the audiometric characteristics of the SSD. In accordance with the findings of the recent animal study, tinnitus was absent in subjects with congenital SSD, but relatively frequent in subjects with acquired SSD, which suggests that the development of tinnitus should be preceded by auditory experience. In other words, subjects with profound congenital peripheral deafferentation do not develop auditory phantom percepts because no auditory predictions are available from the Bayesian brain. Copyright © 2017 Elsevier B.V. All rights

Design of Passive Acoustic Wave Shaping Devices and Their Experimental Validation

DEFF Research Database (Denmark)

Christiansen, Rasmus Ellebæk; Sigmund, Ole; Fernandez Grande, Efren

We discuss a topology optimization based approach for designing passive acoustic wave shaping devices and demonstrate its application to; directional sound emission [1], sound focusing and wave splitting. Optimized devices, numerical and experimental results are presented and benchmarked against...... other designs proposed in the literature. We focus on design problems where the size of the device is on the order of the wavelength, a problematic region for traditional design methods, such as ray tracing.The acoustic optimization problem is formulated in the frequency domain and modeled...

Experimental concept and design of DarkLight, a search for a heavy photon

International Nuclear Information System (INIS)

Cowan, Ray F.

2013-01-01

This talk gives an overview of the DarkLight experimental concept: a search for a heavy photon A′ in the 10-90 MeV/c 2 mass range. After briefly describing the theoretical motivation, the talk focuses on the experimental concept and design. Topics include operation using a half-megawatt, 100 MeV electron beam at the Jefferson Lab FEL, detector design and performance, and expected backgrounds estimated from beam tests and Monte Carlo simulations

Training reactor deployment. Advanced experimental course on designing new reactor cores

International Nuclear Information System (INIS)

Skoda, Radek

2009-01-01

Czech Technical University in Prague (CTU) operating its training nuclear reactor VR1, in cooperation with the North West University of South Africa (NWU), is applying for accreditation of the experimental training course ''Advanced experimental course on designing the new reactor core'' that will guide the students, young nuclear engineering professionals, through designing, calculating, approval, and assembling a new nuclear reactor core. Students, young professionals from the South African nuclear industry, face the situation when a new nuclear reactor core is to be build from scratch. Several reactor core design options are pre-calculated. The selected design is re-calculated by the students, the result is then scrutinized by the regulator and, once all the analysis is approved, physical dismantling of the current core and assembling of the new core is done by the students, under a close supervision of the CTU staff. Finally the reactor is made critical with the new core. The presentation focuses on practical issues of such a course, desired reactor features and namely pedagogical and safety aspects. (orig.)

Technical aspects and recommendations for single-cell qPCR.

Science.gov (United States)

Ståhlberg, Anders; Kubista, Mikael

2018-02-01

Single cells are basic physiological and biological units that can function individually as well as in groups in tissues and organs. It is central to identify, characterize and profile single cells at molecular level to be able to distinguish different kinds, to understand their functions and determine how they interact with each other. During the last decade several technologies for single-cell profiling have been developed and used in various applications, revealing many novel findings. Quantitative PCR (qPCR) is one of the most developed methods for single-cell profiling that can be used to interrogate several analytes, including DNA, RNA and protein. Single-cell qPCR has the potential to become routine methodology but the technique is still challenging, as it involves several experimental steps and few molecules are handled. Here, we discuss technical aspects and provide recommendation for single-cell qPCR analysis. The workflow includes experimental design, sample preparation, single-cell collection, direct lysis, reverse transcription, preamplification, qPCR and data analysis. Detailed reporting and sharing of experimental details and data will promote further development and make validation studies possible. Efforts aiming to standardize single-cell qPCR open up means to move single-cell analysis from specialized research settings to standard research laboratories. Copyright © 2017 Elsevier Ltd. All rights reserved.

A comparison in young and elderly subjects of the pharmacokinetics and pharmacodynamics of single and multiple doses of benazepril.

Science.gov (United States)

Macdonald, N J; Elliott, H L; Hughes, D M; Reid, J L

1993-01-01

1. The pharmacokinetics and pharmacodynamics of single and multiple oral doses of the ACE inhibitor benazepril were investigated in young and elderly normotensive subjects. 2. Following multiple doses the trough concentrations were significantly higher in the elderly and the areas under the plasma concentration-time curves (AUC0-24) were significantly greater, by approximately 23%. 3. The fall in blood pressure tended to be greater in the elderly subjects but this is likely to be attributable to their higher initial blood pressures, although it may reflect the small differences in pharmacokinetics. 4. The age related differences in kinetics and dynamics following multiple dosing are quantitatively similar to those obtained with single doses. However, there appears to be a quantitative difference between benazepril and other ACE inhibitors in that the age related increases were of a relatively smaller magnitude. PMID:9114904

Internet-Based Cognitive Behavioral Therapy for Residual Symptoms in Bipolar Disorder Type II: A Single-Subject Design Pilot Study.

Science.gov (United States)

Holländare, Fredrik; Eriksson, Annsofi; Lövgren, Lisa; Humble, Mats B; Boersma, Katja

2015-04-23

Bipolar disorder is a chronic condition with recurring episodes that often lead to suffering, decreased functioning, and sick leave. Pharmacotherapy in the form of mood stabilizers is widely available, but does not eliminate the risk of a new depressive or (hypo)manic episode. One way to reduce the risk of future episodes is to combine pharmacological treatment with individual or group psychological interventions. However, access to such interventions is often limited due to a shortage of trained therapists. In unipolar depression there is now robust evidence of the effectiveness of Internet-based psychological interventions, usually comprising psychoeducation and cognitive behavioral therapy (CBT). Internet-based interventions for persons suffering from bipolar disorder could increase access to psychological treatment. The aim of this study was to investigate the feasibility of an Internet-based intervention, as well as its effect on residual depressive symptoms in persons diagnosed with bipolar disorder type II (BP-II). The most important outcomes were depressive symptoms, treatment adherence, and whether the patient perceived the intervention as helpful. A total of 7 patients diagnosed with bipolar disorder type II at a Swedish psychiatric outpatient clinic were offered the opportunity to participate. Of the 7 patients, 3 (43%) dropped out before treatment began, and 4 (57%) were treated by means of an online, Internet-based intervention based on CBT (iCBT). The intervention was primarily aimed at psychoeducation, treatment of residual depressive symptoms, emotion regulation, and improved sleep. All patients had ongoing pharmacological treatment at recruitment and established contact with a psychiatrist. The duration of BP-II among the treated patients was between 6 and 31 years. A single-subject design was used and the results of the 4 participating patients were presented individually. Initiating treatment was perceived as too demanding under current life

Multi-objective optimization design and experimental investigation of centrifugal fan performance

Science.gov (United States)

Zhang, Lei; Wang, Songling; Hu, Chenxing; Zhang, Qian

2013-11-01

Current studies of fan performance optimization mainly focus on two aspects: one is to improve the blade profile, and another is only to consider the influence of single impeller structural parameter on fan performance. However, there are few studies on the comprehensive effect of the key parameters such as blade number, exit stagger angle of blade and the impeller outlet width on the fan performance. The G4-73 backward centrifugal fan widely used in power plants is selected as the research object. Based on orthogonal design and BP neural network, a model for predicting the centrifugal fan performance parameters is established, and the maximum relative errors of the total pressure and efficiency are 0.974% and 0.333%, respectively. Multi-objective optimization of total pressure and efficiency of the fan is conducted with genetic algorithm, and the optimum combination of impeller structural parameters is proposed. The optimized parameters of blade number, exit stagger angle of blade and the impeller outlet width are seperately 14, 43.9°, and 21 cm. The experiments on centrifugal fan performance and noise are conducted before and after the installation of the new impeller. The experimental results show that with the new impeller, the total pressure of fan increases significantly in total range of the flow rate, and the fan efficiency is improved when the relative flow is above 75%, also the high efficiency area is broadened. Additionally, in 65% -100% relative flow, the fan noise is reduced. Under the design operating condition, total pressure and efficiency of the fan are improved by 6.91% and 0.5%, respectively. This research sheds light on the considering of comprehensive effect of impeller structrual parameters on fan performance, and a new impeller can be designed to satisfy the engineering demand such as energy-saving, noise reduction or solving air pressure insufficiency for power plants.

Design/build: A Relevant Pedagogy for Architecture Education

Directory of Open Access Journals (Sweden)

Olivier Chamel

2016-12-01

This paper will present a series of recent furniture design/build exercises where students designed and furniture and small building prototypes with limited reliance on drawings. We will discuss how subjects such as structures, material sourcing and construction detailing can be transposed from various courses and applied to design/build projects. We believe that a pedagogy based on physical experimentations could infuse energy throughout curricula no matter the course subject.

Design optimization of single-main-amplifier KrF laser-fusion systems

International Nuclear Information System (INIS)

Harris, D.B.; Pendergrass, J.H.

1985-01-01

KrF lasers appear to be a very promising laser fusion driver for commercial applications. The Large Amplifier Module for the Aurora Laser System at Los Alamos is the largest KrF laser in the world and is currently operating at 5 kJ with 10 to 15 kJ eventually expected. The next generation system is anticipated to be a single-main-amplifier system that generates approximately 100 kJ. This paper examines the cost and efficiency tradeoffs for a complete single-main-amplifier KrF laser fusion experimental facility. It has been found that a 7% efficient $310/joule complete laser-fusion system is possible by using large amplifier modules and high optical fluences

Enhancement of in vitro interleukin-2 production in normal subjects following a single spinal manipulative treatment

Directory of Open Access Journals (Sweden)

Harris Glen M

2008-05-01

Full Text Available Abstract Background Increasing evidence supports somato-visceral effects of manual therapies. We have previously demonstrated that a single spinal manipulative treatment (SMT accompanied by audible release has an inhibitory effect on the production of proinflammatory cytokines in asymptomatic subjects. The purpose of this study is to report on SMT-related changes in the production of the immunoregulatory cytokine interleukin 2 (IL-2 and to investigate whether such changes might differ with respect to the treatment approach related to the presence or absence of an audible release (joint cavitation. Methods Of 76 asymptomatic subjects, 29 received SMT with cavitation (SMT-C, 23 were treated with SMT without cavitation (SMT-NC and 24 comprised the venipuncture control (VC group. The SMT-C and SMT-NC subjects received a single, similar force high velocity low amplitude manipulation, in the upper thoracic spine. However, in SMT-NC subjects, positioning and line of drive were not conducive to cavitation. Blood and serum samples were obtained before and then at 20 and 120 min post-intervention. The production of IL-2 in peripheral blood mononuclear cell cultures was induced by activation for 48 hr with Staphylococcal protein A (SPA and, in parallel preparations, with the combination of phorbol ester (TPA and calcium ionophore. The levels of IL-2 in culture supernatants and serum were assessed by specific immunoassays. Results Compared with VC and their respective baselines, SPA-induced secretion of IL-2 increased significantly in cultures established from both SMT-C and SMT-NC subjects at 20 min post-intervention. At 2 hr post-treatment, significant elevation of IL-2 synthesis was still apparent in preparations from SMT-treated groups though it became somewhat attenuated in SMT-NC subjects. Conversely, IL-2 synthesis induced by TPA and calcium ionophore was unaltered by either type of SMT and was comparable to that in VC group at all time points. No

Spent Fuel Transportation Package Performance Study - Experimental Design Challenges

International Nuclear Information System (INIS)

Snyder, A. M.; Murphy, A. J.; Sprung, J. L.; Ammerman, D. J.; Lopez, C.

2003-01-01

Numerous studies of spent nuclear fuel transportation accident risks have been performed since the late seventies that considered shipping container design and performance. Based in part on these studies, NRC has concluded that the level of protection provided by spent nuclear fuel transportation package designs under accident conditions is adequate. [1] Furthermore, actual spent nuclear fuel transport experience showcase a safety record that is exceptional and unparalleled when compared to other hazardous materials transportation shipments. There has never been a known or suspected release of the radioactive contents from an NRC-certified spent nuclear fuel cask as a result of a transportation accident. In 1999 the United States Nuclear Regulatory Commission (NRC) initiated a study, the Package Performance Study, to demonstrate the performance of spent fuel and spent fuel packages during severe transportation accidents. NRC is not studying or testing its current regulations, a s the rigorous regulatory accident conditions specified in 10 CFR Part 71 are adequate to ensure safe packaging and use. As part of this study, NRC currently plans on using detailed modeling followed by experimental testing to increase public confidence in the safety of spent nuclear fuel shipments. One of the aspects of this confirmatory research study is the commitment to solicit and consider public comment during the scoping phase and experimental design planning phase of this research

The role of model-based methods in the development of single scan techniques

International Nuclear Information System (INIS)

Laruelle, Marc

2000-01-01

Single scan techniques are highly desirable for clinical trials involving radiotracers because they increase logistical feasibility, improve patient compliance, and decrease the cost associated with the study. However, the information derived from single scans usually are biased by factors unrelated to the process of interest. Therefore, identification of these factors and evaluation of their impact on the proposed outcome measure is important. In this paper, the impact of confounding factors on single scan measurements is illustrated by discussing the effect of between-subject or between-condition differences in radiotracer plasma clearance on normalized activity ratios (specific to nonspecific ratios) in the tissue of interest. Computer simulation based on kinetic analyses are presented to demonstrate this effect. It is proposed that the presence of this and other confounding factors should not necessarily preclude clinical trials based on single scan techniques. First, knowledge of the distribution of plasma clearance values in a sample of the investigated population allows researchers to assign limits to this potential bias. This information can be integrated in the power analysis. Second, the impact of this problem will vary according to the characteristic of the radiotracer, and this information can be used in the development and selection of the radiotracer. Third, simple modification of the experimental design (such as administration of the radiotracer as a bolus, followed by constant infusion, rather than as a single bolus) might remove this potential confounding factor and allow appropriate quantification within the limits of a single scanning session. In conclusion, model-based kinetic characterization of radiotracer distribution and uptake is critical to the design and interpretation of clinical trials based on single scan techniques

Experimental use of iteratively designed rotation invariant correlation filters

International Nuclear Information System (INIS)

Sweeney, D.W.; Ochoa, E.; Schils, G.F.

1987-01-01

Iteratively designed filters are incorporated into an optical correlator for position, rotation, and intensity invariant recognition of target images. The filters exhibit excellent discrimination because they are designed to contain full information about the target image. Numerical simulations and experiments demonstrate detection of targets that are corrupted with random noise (SNR≅0.5) and also partially obscured by other objects. The complex valued filters are encoded in a computer generated hologram and fabricated directly using an electron-beam system. Experimental results using a liquid crystal spatial light modulator for real-time input show excellent agreement with analytical and numerical computations

Experimental verification of secondary effects of prestressed beam at ULS

Directory of Open Access Journals (Sweden)

Peter Pažma

2016-03-01

Full Text Available The paper deals with secondary effects of prestressing at ultimate limit state when statically indeterminate structure has changed its structural form due to development of plastic hinges in critical cross-sections. The article presents results of an experimental program which was carried out at Slovak University of Technology in Bratislava on two span continuous beams post-tensioned by two single-strand tendons subjected to experimental load which has changed structural system into kinematic mechanism.

Reference design (MK-I and MK-II) for experimental multi-purpose VHTR

International Nuclear Information System (INIS)

Miyamoto, Yoshiaki; Suzuki, Kunihiko; Sato, Sadao

1975-10-01

This report summarizes the results of a study on thermal and mechanical performances of the core, which are obtained in course of reference design (Mk-I and Mk-II) for the experimental multi-purpose VHTR: (1) Design criteria, design methods and design data. These bases are also discussed in order to refer in the case of proceeding a next design work. (2) The results of performance analysis such as the initial core and its prediction for the irradiated core. (auth.)

Experimental study of liquid-metal target designs of accelerating-controlled systems

International Nuclear Information System (INIS)

Iarmonov, Mikhail; Makhov, Kirill; Novozhilova, Olga; Meluzov, A.G.; Beznosov, A.V.

2011-01-01

Models of a liquid-metal target of an accelerator-controlled system have been experimentally studied at the Nizhny Novgorod State Technical University to develop an optimal design of the flow part of the target. The main explored variants of liquid-metal targets are: Design with a diaphragm (firm-and-impervious plug) mounted on the pipe tap of particle transport from the accelerator cavity to the working cavity of the liquid-metal target. Design without a diaphragm on the pipe tab of particle transport from the accelerator. The study was carried out in a high-temperature liquid-metal test bench under the conditions close to full-scale ones: the temperature of the eutectic lead-bismuth alloy was 260degC - 400degC, the coolant mass flow was 5-80 t/h, and the rarefaction in the gas cavity was 10 5 Pa, the coefficient of geometric similarity equal to 1. The experimental studies of hydrodynamic characteristics of flow parts in the designs of targets under full-scale conditions indicated high efficiency of a target in triggering, operating, and deactivating modes. Research and technology instructions for designs of the flow part of the liquid-metal target, the target design as a whole, and the target circuit of accelerator-controlled systems were formulated as a result of the studies. (author)

Application of Iterative Robust Model-based Optimal Experimental Design for the Calibration of Biocatalytic Models

DEFF Research Database (Denmark)

Van Daele, Timothy; Gernaey, Krist V.; Ringborg, Rolf Hoffmeyer

2017-01-01

The aim of model calibration is to estimate unique parameter values from available experimental data, here applied to a biocatalytic process. The traditional approach of first gathering data followed by performing a model calibration is inefficient, since the information gathered during...... experimentation is not actively used to optimise the experimental design. By applying an iterative robust model-based optimal experimental design, the limited amount of data collected is used to design additional informative experiments. The algorithm is used here to calibrate the initial reaction rate of an ω......-transaminase catalysed reaction in a more accurate way. The parameter confidence region estimated from the Fisher Information Matrix is compared with the likelihood confidence region, which is a more accurate, but also a computationally more expensive method. As a result, an important deviation between both approaches...

An experimental study on pile spacing effects under lateral loading in sand.