WorldWideScience

Sample records for single-loads presently housed

  1. Short-term heat load forecasting for single family houses

    DEFF Research Database (Denmark)

    Bacher, Peder; Madsen, Henrik; Nielsen, Henrik Aalborg

    2013-01-01

    This paper presents a method for forecasting the load for space heating in a single-family house. The forecasting model is built using data from sixteen houses located in Sønderborg, Denmark, combined with local climate measurements and weather forecasts. Every hour the hourly heat load for each...... house the following two days is forecasted. The forecast models are adaptive linear time-series models and the climate inputs used are: ambient temperature, global radiation and wind speed. A computationally efficient recursive least squares scheme is used. The models are optimized to fit the individual...... noise and that practically all correlation to the climate variables are removed. Furthermore, the results show that the forecasting errors mainly are related to: unpredictable high frequency variations in the heat load signal (predominant only for some houses), shifts in resident behavior patterns...

  2. Online short-term heat load forecasting for single family houses

    DEFF Research Database (Denmark)

    Bacher, Peder; Madsen, Henrik; Nielsen, Henrik Aalborg

    2013-01-01

    . Every hour the hourly heat load for each house the following two days is forecasted. The forecast models are adaptive linear time-series models and the climate inputs used are: ambient temperature, global radiation, and wind speed. A computationally efficient recursive least squares scheme is used......This paper presents a method for forecasting the load for heating in a single-family house. Both space and hot tap water heating are forecasted. The forecasting model is built using data from sixteen houses in Sønderborg, Denmark, combined with local climate measurements and weather forecasts...... variations in the heat load signal (predominant only for some houses), peaks presumably from showers, shifts in resident behavior, and uncertainty of the weather forecasts for longer horizons, especially for the solar radiation....

  3. Transient analysis of house load operation for LNPP

    International Nuclear Information System (INIS)

    Shi Junying; Zheng Bin

    2000-01-01

    The author analysis the transient of house load operation for Ling'ao Nuclear Power Plant by using the methods of dynamic simulation and closed loops of primary and secondary system. The transient of house load operation from 100% FP is the most severe that can occur on the unit in normal operation because it causes immediately shedding of 95% of turbine load and requires the unit to operate steadily at reduced power. The results show that the transient can be successful both at beginning of core life and manual house load operation. However, more attentions must be paid to automatic house load operation caused by grid fault at toward end of core life because the success of the transient could be threatened by the actuation of the protection of high flux and high flux rate

  4. Sex differences in muscular load among house painters performing identical work tasks

    DEFF Research Database (Denmark)

    Meyland, Jacob; Heilskov-Hansen, Thomas; Alkjær, Tine

    2014-01-01

    PURPOSE: The present study aimed to estimate possible differences in upper body muscular load between male and female house painters performing identical work tasks. Sex-related differences in muscular load may help explain why women, in general, have more musculoskeletal complaints than men....... METHODS: In a laboratory setting, 16 male and 16 female house painters performed nine standardised work tasks common to house painters. Unilateral electromyography (EMG) recordings were obtained from the supraspinatus muscle by intramuscular electrodes and from the trapezius, extensor and flexor carpi...... radialis muscles by surface electrodes. Relative muscular loads in %EMGmax as well as exerted force in Newton, based on ramp calibrations, were assessed. Sex differences were tested using a mixed model approach. RESULTS: Women worked at about 50% higher relative muscular loads than men in the supraspinatus...

  5. On the thermal inertia and time constant of single-family houses

    Energy Technology Data Exchange (ETDEWEB)

    Hedbrant, J.

    2001-08-01

    Since the 1970s, electricity has become a common heating source in Swedish single-family houses. About one million small houses can use electricity for heating, about 600.000 have electricity as the only heating source, A liberalised European electricity market would most likely raise the Swedish electricity prices during daytime on weekdays and lower it at other times. In the long run, electrical heating of houses would be replaced by fuels, but in the shorter perspective, other strategies may be considered. This report evaluates the use of electricity for heating a dwelling, or part of it, at night when both the demand and the price are low. The stored heat is utilised in the daytime some hours later, when the electricity price is high. Essential for heat storage is the thermal time constant. The report gives a simple theoretical framework for the calculation of the time constant for a single-family house with furniture. Furthermore the comfort time constant, that is, the time for a house to cool down from a maximum to a minimum acceptable temperature, is derived. Two theoretical model houses are calculated, and the results are compared to data from empirical studies in three inhabited test houses. The results show that it was possible to store about 8 kWh/K in a house from the seventies and about 5 kWh/K in a house from the eighties. The time constants were 34 h and 53 h, respectively. During winter conditions with 0 deg C outdoor, the 'comfort' time constants with maximum and minimum indoor temperatures of 23 and 20 deg C were 6 h and 10 h. The results indicate that the maximum load-shifting potential of an average single family house is about 1 kw during 16 daytime hours shifted into 2 kw during 8 night hours. Upscaled to the one million Swedish single-family houses that can use electricity as a heating source, the maximum potential is 1000 MW daytime time-shifted into 2000 MW at night.

  6. Evaluation of load rejection to house load test at 50% power for UCN 3

    International Nuclear Information System (INIS)

    Lee, Chang Gyun; Sohn, Suk Whun; Sohn, Jong Joo; Seo, Jong Tae; Lee, Sang Keun; Kim, Yong Sung; Nam, Kyu Won; Jung, Yang Mook; Chae, Kyeong Sik; Koh, Bum Jae; Oh, Chul Sung; Park, Hee Chool

    1998-01-01

    The Load Rejection to House Load test at 50% power was successfully performed during the UCN 3 PAT period. In this test, all plant control systems automatically controlled the plant from 50% power to house load operation mode. The KISPAC code, which was used in the performance analysis during the design process of UCN 3 and 4, predictions of the test agreed with the measured data demonstrating the validity of the code as well as completeness of the plant design

  7. Evaluation of Load Rejection to house load test at 50% power for UCN 3

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chang Gyun; Sohn, Suk Whun; Sohn, Jong Joo; Seo, Jong Tae; Lee, Sang Keun [Korea Power Engineering Company, Inc., Seoul (Korea, Republic of); Kim, Yong Sung; Nam, Kyu Won; Jung, Yang Mook; Chae, Kyeong Sik; Koh, Bum Jae; Oh, Chul Sung; Park, Hee Chool [Korea Electric Power Corporation, Taejon (Korea, Republic of)

    1999-12-31

    The Load Rejection to House Load test at 50% power was successfully performed during the UCN 3 PAT period. In this test, all plant control systems automatically controlled the plant from 50% power to house load operation mode. The KISPAC code, which was used in the performance analysis during the design process of UCN 3 and 4, predictions of the test agreed with the measured data demonstrating the validity of the code as well as the completeness of the plant design. 3 refs., 8 figs., 1 tab. (Author)

  8. Evaluation of Load Rejection to house load test at 50% power for UCN 3

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chang Gyun; Sohn, Suk Whun; Sohn, Jong Joo; Seo, Jong Tae; Lee, Sang Keun [Korea Power Engineering Company, Inc., Seoul (Korea, Republic of); Kim, Yong Sung; Nam, Kyu Won; Jung, Yang Mook; Chae, Kyeong Sik; Koh, Bum Jae; Oh, Chul Sung; Park, Hee Chool [Korea Electric Power Corporation, Taejon (Korea, Republic of)

    1998-12-31

    The Load Rejection to House Load test at 50% power was successfully performed during the UCN 3 PAT period. In this test, all plant control systems automatically controlled the plant from 50% power to house load operation mode. The KISPAC code, which was used in the performance analysis during the design process of UCN 3 and 4, predictions of the test agreed with the measured data demonstrating the validity of the code as well as the completeness of the plant design. 3 refs., 8 figs., 1 tab. (Author)

  9. SBS symptoms in relation to dampness and ventilation in inspected single-family houses in Sweden.

    Science.gov (United States)

    Smedje, Greta; Wang, Juan; Norbäck, Dan; Nilsson, Håkan; Engvall, Karin

    2017-10-01

    To investigate the relationships between symptoms compatible with the sick building syndrome (SBS) in adults and building dampness and ventilation in single-family houses. Within the Swedish BETSI study, a national sample of single-family houses were inspected by professional building experts, and adults living in the houses answered a questionnaire on SBS. Relationships between building factors and SBS were analysed using logistic regression. Of the respondents, 23% reported having had weekly SBS symptoms during the last three months. A large proportion of houses exhibited building or construction problems. In total, 40% of houses had dampness problems in the foundation, and this was related to a higher prevalence of both mucous and dermal symptoms, and any SBS symptoms. Furthermore, high air humidity was related to more symptoms, with the relationship with absolute humidity being stronger than that with relative humidity or moisture load. Symptoms were also more prevalent in houses with a high U value, reflecting a poor thermal insulation. Compared to natural ventilation, living in a house with mechanical supply and exhaust ventilation was related to a lower prevalence of general symptoms and any SBS symptoms, but there were only weak associations between measured air exchange rate and symptoms. A large proportion of single-family houses have dampness problems in the foundation, and pollutants may enter the living space of the house and affect the health of the occupants. Furthermore, absolute air humidity should be measured more often in indoor air studies.

  10. Tobin's q for Danish single-family houses

    DEFF Research Database (Denmark)

    Haagerup, Christian Deichmann

    from 2003 to 2006. The activity in the construction sector has been increasing too, but with some time lag caused by what seems to be an inelastic supply. In the long run, house prices will be determined by the replacement cost of houses, e.g. the cost of constructing a similar house including the cost...... of land. This can be used as a guide as to how much prices are to fall, in order to bring them back to the fundamental value. It can also be seen as a warning or indication of a price bubble. This paper presents a calculation of the value of Tobin's q for single-family houses in Denmark from 1968 to 2008....... It shows that the value of Tobin's q has risen by around 40 percent from 2003 to 2006, caused by increasing house prices. This was not a sustainable development, and prices and the value of Tobin's q are now falling. In order for the value of Tobin's q to reach its fundamental value of 1, prices have...

  11. Housing Retention in Single-Site Housing First for Chronically Homeless Individuals With Severe Alcohol Problems

    Science.gov (United States)

    Malone, Daniel K.; Clifasefi, Seema L.

    2013-01-01

    Objectives. We studied housing retention and its predictors in the single-site Housing First model. Methods. Participants (n = 111) were chronically homeless people with severe alcohol problems who lived in a single-site Housing First program and participated in a larger nonrandomized controlled trial (2005–2008) conducted in Seattle, Washington. At baseline, participants responded to self-report questionnaires assessing demographic, illness burden, alcohol and other drug use, and psychiatric variables. Housing status was recorded over 2 years. Results. Participants were interested in housing, although a sizable minority did not believe they would be able to maintain abstinence-based housing. Only 23% of participants returned to homelessness during the 2-year follow-up. Commonly cited risk factors—alcohol and other drug use, illness burden, psychiatric symptoms, and homelessness history—did not predict resumed homelessness. Active drinkers were more likely to stay in this housing project than nondrinkers. Conclusions. We found that single-site Housing First programming fills a gap in housing options for chronically homeless people with severe alcohol problems. PMID:24148063

  12. 76 FR 31217 - Single Family Housing Guaranteed Loan Program

    Science.gov (United States)

    2011-05-31

    ... Farm Service Agency 7 CFR Part 1980 RIN 0575-AC83 Single Family Housing Guaranteed Loan Program... the Rural Housing Service (RHS) Section 502 Single Family Housing Guaranteed Loan Program (SFHGLP) by eliminating the lender's published Department of Veterans Affairs (VA) rate for first mortgage loans with no...

  13. Single-Family Houses That Meet The Future Energy Demands

    DEFF Research Database (Denmark)

    Rose, Jørgen; Svendsen, Svend

    2002-01-01

    ). Before any further tightening of the regulations are introduced, however, it is necessary to illustrate the consequences of such actions with regard to finance, building technology, indoor climate and comfort. Therefore a series of investigations and experimental projects are being launched, in order...... to examine these consequences thoroughly. The department is presently contributing to this end by participating in quite a few investigative projects, where single-family houses are designed to meet the proposed future energy demands. This paper describes the results obtained from one such project where...... the department, in co-operation with a major building entrepreneur, has developed a single-family house that shows that there are no evident problems in meeting the future energy demands....

  14. Canadian House Dust Study: Population-based concentrations, loads and loading rates of arsenic, cadmium, chromium, copper, nickel, lead, and zinc inside urban homes

    Energy Technology Data Exchange (ETDEWEB)

    Rasmussen, Pat E. [Exposure and Biomonitoring Division, Healthy Environments and Consumer Safety Branch, Health Canada, 50 Colombine Driveway, Ottawa, ON, Canada K1A 0K9 (Canada); Department of Earth Sciences, University of Ottawa, 140 Louis Pasteur, Ottawa, ON, Canada K1N 6N5 (Canada); Levesque, Christine [Exposure and Biomonitoring Division, Healthy Environments and Consumer Safety Branch, Health Canada, 50 Colombine Driveway, Ottawa, ON, Canada K1A 0K9 (Canada); Chénier, Marc; Gardner, H. David [Exposure and Biomonitoring Division, Healthy Environments and Consumer Safety Branch, Health Canada, 50 Colombine Driveway, Ottawa, ON, Canada K1A 0K9 (Canada); Department of Earth Sciences, University of Ottawa, 140 Louis Pasteur, Ottawa, ON, Canada K1N 6N5 (Canada); Jones-Otazo, Heather [Regions and Programs Branch, Health Canada, 180 Queen Street West, Toronto, ON, Canada M5V 3L7 (Canada); Petrovic, Sanya [Contaminated Sites Division, Healthy Environments and Consumer Safety Branch, Health Canada, 269 Laurier Ave West, Ottawa, ON, Canada K1A 0K9 (Canada)

    2013-01-15

    The Canadian House Dust Study was designed to obtain nationally representative urban house dust metal concentrations (μg g{sup −1}) and metal loadings (μg m{sup −2}) for arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni), lead (Pb), and zinc (Zn). Consistent sampling of active dust of known age and provenance (area sampled) also permitted the calculation of indoor loading rates (mg m{sup −2} day{sup −1} for dust and μg m{sup −2} day{sup −1} for metals) for the winter season (from 2007 to 2010) when houses are most tightly sealed. Geomean/median indoor dust loading rates in homes located more than 2 km away from industry of any kind (9.6/9.1 mg m{sup −2} day{sup −1}; n = 580) were significantly lower (p < .001) than geomean (median) dust loading rates in homes located within 2 km of industry (13.5/13.4 mg m{sup −2} day{sup −1}; n = 421). Proximity to industry was characterized by higher indoor metal loading rates (p < .003), but no difference in dust metal concentrations (.29 ≥ p ≤ .97). Comparisons of non-smokers' and smokers' homes in non-industrial zones showed higher metal loading rates (.005 ≥ p ≤ .038) in smokers' homes, but no difference in dust metal concentrations (.15 ≥ p ≤ .97). Relationships between house age and dust metal concentrations were significant for Pb, Cd and Zn (p < .001) but not for the other four metals (.14 ≥ p ≤ .87). All seven metals, however, displayed a significant increase in metal loading rates with house age (p < .001) due to the influence of higher dust loading rates in older homes (p < .001). Relationships between three measures of metals in house dust – concentration, load, and loading rate – in the context of house age, smoking behavior and urban setting consistently show that concentration data is a useful indicator of the presence of metal sources in the home, whereas dust mass is the overriding influence on metal loadings and loading rates

  15. Thermal design of a modern, air-conditioned, single-floor, solar-powered desert house

    KAUST Repository

    Serag-Eldin, M. A.

    2011-01-01

    The paper presents a thermal analysis of a single-floor, solar-powered desert house. The house is air-conditioned and provides all modern comforts and facilities. Electrical power, which drives the entire energy system, is generated by roof

  16. Friction-loaded cycle ergometers: Past, present and future

    Directory of Open Access Journals (Sweden)

    Henry Vandewalle

    2015-12-01

    Full Text Available The first friction-cycle ergometers of the end of the nineteenth century and the beginning of the 20th century are presented before the description of more recent ergometers such as Fleisch ergometer (1954, ErgomécaTM (1985, sinus-balance ergometer, and weight-basket loaded ergometer. The limits of each ergometer are debated. The interest of friction-loaded ergometers was renewed with the proposal of different protocols enabling the assessment of maximal power during short all-out sprints on a cycle ergometer. These protocols are succinctly presented: corrected peak power protocol, force-speed test during repeated all-out sprints against different loads, torque–velocity relationship during a single all-out sprint. The different calibration procedures (static, dynamic, and physiological calibrations of friction-loaded ergometers are described before the presentation of their results in the literature. Some improvements for the future friction-loaded ergometers are presented at the end of the paper.

  17. Optimal Operation Method of Smart House by Controllable Loads based on Smart Grid Topology

    Science.gov (United States)

    Yoza, Akihiro; Uchida, Kosuke; Yona, Atsushi; Senju, Tomonobu

    2013-08-01

    From the perspective of global warming suppression and depletion of energy resources, renewable energy such as wind generation (WG) and photovoltaic generation (PV) are getting attention in distribution systems. Additionally, all electrification apartment house or residence such as DC smart house have increased in recent years. However, due to fluctuating power from renewable energy sources and loads, supply-demand balancing fluctuations of power system become problematic. Therefore, "smart grid" has become very popular in the worldwide. This article presents a methodology for optimal operation of a smart grid to minimize the interconnection point power flow fluctuations. To achieve the proposed optimal operation, we use distributed controllable loads such as battery and heat pump. By minimizing the interconnection point power flow fluctuations, it is possible to reduce the maximum electric power consumption and the electric cost. This system consists of photovoltaics generator, heat pump, battery, solar collector, and load. In order to verify the effectiveness of the proposed system, MATLAB is used in simulations.

  18. Energy efficient demand controlled ventilation in single family houses

    DEFF Research Database (Denmark)

    Nielsen, Toke Rammer; Drivsholm, Christian

    2010-01-01

    This paper presents a strategy for a simple demand controlled ventilation system for single family houses where all sensors and controls are located in the air handling unit. The strategy is based on sensing CO2-concentration and moisture content in the outdoor air and exhaust air. The CO2...

  19. Economy Controls Energy Retrofits of Danish Single-family Houses

    DEFF Research Database (Denmark)

    Mortensen, Andrea; Heiselberg, Per; Knudstrup, Mary-Ann

    2014-01-01

    A great energy saving potential is found in the 440,000 Danish single-family houses erected between 1960 and 1979, but the potential is not exploited. To utilize this potential homeowners must be motivated to conduct energy saving retrofits. This paper presents results from a survey from 2012 where...... 883 Danish single-family house owners completed a questionnaire about energy retrofit. The objective of this paper is, based on the survey results, to determine how Danish homeowners can be motivated to conduct energy retrofits. The conclusion is that the financial aspect of an energy retrofit...... about the potential improvements within these parameters is found among the homeowners and therefore there is a vital need for more information about this. A combination of this knowledge of the non-economic improvements, a sensible investment size and information and education about the current...

  20. Energy plus standard in buildings constructed by housing associations?

    International Nuclear Information System (INIS)

    Stutterecker, Werner; Blümel, Ernst

    2012-01-01

    In order to achieve national, European and international energy goals, energy efficiency strategies in the building sector have to be implemented. The passive house standard and low energy standards are already successfully established in single dwelling houses. These high performance standards are starting to penetrate into the sector of housing associations. A case study about an apartment building constructed by a housing association is presented here. It describes the monitoring concept and the results of the 1st year of monitoring. Depending on the definition of the zero energy building standard (extent of loads included in the balancing), the building could be classified as an energy plus building or as a building, which uses more energy, than is supplied by on-site generation. If the building's total energy use (including user specific loads) is defined as load, only 34.5% of these loads were provided by the net energy output of the PV system. If only the heating energy demand is defined as load, the PV system even yielded a surplus of 45.6% of the energy load. -- Highlights: ► Energy monitoring of an apartment building constructed by a housing association. ► Planned as a Passive House with a semi-central ventilation system with decentralized heat pump technology. ► Total end energy demand of the building was 43 kWh/(m² a). ► Total net energy generation by the PV system was 15 kWh/(m² a). ► Apartment no. 1: 52% of the energy demand were used for heating and ventilation.

  1. Seasonal variations of radon concentrations in single-family houses with different sub-structures

    DEFF Research Database (Denmark)

    Majborn, B.

    1992-01-01

    Seasonal variations of indoor radon concentrations have been studied in 70 single-family houses selected according to the type of sub-structure and the type of soil underneath the house. Five categories of sub-structure were included - slab-on-grade, crawl space, basement, and combinations...... of basement with slab-on-grade or crawl space. Half of the houses are located on clayey till and the other half on glaciofluvial gravel. In each house radon was measured in a living room and a bedroom, in the basement if present, and in the crawl space if present and accessible. The measurements were made...... with track detectors on a quarterly basis throughout a year. For living rooms and bedrooms the seasonal variations range from being highly significant for the slab-on-grade houses to being insignificant for the crawl space houses. For basements and crawl spaces the geometric mean radon concentrations do...

  2. Detail, Facture, and Colour in the Architecture of Polish Single-Family Houses after 1989

    Science.gov (United States)

    Sztafrowski, Marek

    2017-10-01

    The article presents single-family houses architecture transformations since 1989, with particularly close attention paid to the significance of detail, facture, and colour. The article presents the architecture as an art of designing and building facilities with both use and aesthetic value, an art of shaping space and building forms. Architectural work should correspond to the intended function, technique, economic and aesthetic requirements, thus shaping all elements of human immediate environment, both inside and outside of the building. Architecture of the building is perceived as form, structure, and function, as well as detail, facture, and colour. Facture and colour are created through materials used for external finishes. The solid of the building is noticed first while looking at the building, then the finishes detail such as colour, facture, and detail. Materials for external finishes are commonly selected for their aesthetic value equally with their technical characteristics. The detail was always a characteristic element of style. However, currently the fashion for details can be observed, the fashion for usage of materials for external finishes and inter-connected with that colour and facture. The architecture of Polish single-family houses underwent considerable metamorphosis after system change of 1989 - from destitute in form, devoid in detail and colour socmodernism, to architecture extremely varied in terms of form, utilised structures, materials, and detail. Hence, appearance of the phenomenon called fashion can be observed in the architecture, understood as constant changeability, seeking novelty, and creation based on opinion-forming centres. The architectural fashion consists of form, function, structure, building materials, detail, facture, and colour trends, e.g. after rejecting socmodernism, steep roofs characteristic for single-family houses trend started. After 1989, initially individual single-family house projects were created; however

  3. Analysis of gear reducer housing using the finite element method

    Science.gov (United States)

    Miklos, I. Zs; Miklos, C. C.; Alic, C. I.; Raţiu, S.

    2018-01-01

    The housing is an important component in the construction of gear reducers, having the role of fixing the relative position of the shafts and toothed wheels. At the same time, the housing takes over, via the bearings, the shaft loads resulting when the toothed wheel is engaging another toothed mechanism (i.e. power transmission through belts or chains), and conveys them to the foundation on which it is anchored. In this regard, in order to ensure the most accurate gearing, a high stiffness of the housing is required. In this paper, we present the computer-aided 3D modelling of the housing (in cast version) of a single stage cylindrical gear reducer, using the Autodesk Inventor Professional software, on the principle of constructive sizing. For the housing resistance calculation, we carried out an analysis using the Autodesk Simulation Mechanical software to apply the finite element method, based on the actual loads, as well as a comparative study of the stress and strain distribution, for several tightening values of the retaining bolts that secure the cover and the foundation housing.

  4. Introduction to Single Piles under Lateral Loading

    DEFF Research Database (Denmark)

    Augustesen, Anders; Ibsen, Lars Bo

    .2). The description is based on results of laboratory tests, full-scale field tests as well as numerical investigations presented in literature. Second, general methods that attempt to model lateral pile response are discussed in section 1.4. Third, focus is paid to a widely used method for prediction of the response......The purpose of this chapter is to give a short introduction to single piles subjected to lateral loading. First, the observed behaviour of laterally loaded piles is described, i.e. the effects of loading conditions, installation procedure, pile type etc. on pile behaviour are presented (section 1...... of a lateral loaded pile, namely the Winkler approach in which the pile is modelled as an elastic beam on an elastic foundation (section 1.5). The soil response and thereby the elastic foundation is represented by springs with nonlinear behaviour (p-y curves). In section 1.6 different types and formulations...

  5. Existing sustainable renovation concepts for single-family houses

    DEFF Research Database (Denmark)

    Tommerup, Henrik M.; Vanhoutteghem, Lies; Svendsen, Svend

    2010-01-01

    In the Nordic Innovation Centre Project, SuccessFamilies, the main objective is to change the business environment in order to speed up the implementation of sustainable renovation of single-family houses – proposing new service concepts that will combine both the technical solutions, financing...... with individual solutions, traditional warehouses ”do-it-yourself-shops” and some actors marketing single products. To speed up the implementation of sustainable renovation of single-family houses there is a great need for full-service packages. Existing technical renovation concepts, typically focusing...... services as well as other promoting issues to overcome the behavioural, organizational, legal and social barriers that exist in sustainable renovation. A starting point for such a change has been to get an overview of the existing sustainable renovation concepts, i.e. full-service concepts and technical...

  6. Energy renovation of single-family houses in Denmark utilising long-term financing based on equity

    DEFF Research Database (Denmark)

    Kragh, Jesper; Rose, Jørgen

    2011-01-01

    This paper aims to present an economic overview of the opportunities for energy renovation of single-family houses in Denmark financed over the long term. The paper focuses on the economic difference between energy savings and the repayment of investment. Taking out the average remaining 20% equity...... in long-term property mortgage loans and utilising it for extensive energy renovation improves both the economy and the extent of included measures. Approximately 30% of energy consumption in Denmark is used for space heating. The existing 1 million single-family houses account for approximately half...

  7. 75 FR 9867 - Discontinuation of the Notice of Availability of Funding; Multi-Family Housing, Single Family...

    Science.gov (United States)

    2010-03-04

    ... Discontinuation of the Notice of Availability of Funding; Multi- Family Housing, Single Family Housing AGENCY... its existing and continuing Multi-Family and Single-Family Housing programs for which it receives... Analyst, Multi- Family Housing Programs, telephone 202-720-1753 and Myron Wooden, Loan Specialist, Single...

  8. Low-Load Space Conditioning Needs Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Puttagunta, Srikanth [Consortium for Advanced Residential Buildings, Norwalk, CT (United States)

    2015-05-01

    With limited low-load options in the HVAC market, many new-construction housing units are being fitted with oversized equipment - thus facing penalties in system efficiency, comfort, and cost. To bridge the gap between currently available HVAC equipment and the rising demand for low-load HVAC equipment in the marketplace, HVAC equipment manufacturers need to be fully aware of multifamily buildings and single-family homes market needs. Over the past decade, Steven Winter Associates, Inc. (SWA) has provided certification and consulting services on hundreds of housing projects and has accrued a large pool of data. CARB compiled and analyzed these data to see what the thermal load ranges are in various multifamily apartments and attached single-family home types (duplex and townhouse). In total, design loads from 941 dwellings from SWA's recent multifamily and attached single-family work across the Northeast and Mid-Atlantic were analyzed. Information on the dwelling characteristics, design loads, and the specifications of installed mechanical equipment were analyzed to determine any trends that exist within the dataset.

  9. Efficiency of single-family houses and harmonisation of their life cycle participants’ interests

    Directory of Open Access Journals (Sweden)

    Nerija Kvederyte

    2000-01-01

    Full Text Available An efficient single-family house is the main purpose of the life cycle. It determines the necessity to evaluate various decisions of the life cycle of single-family houses and possibilities to satisfy objectives and requirements of the participants of that process. To design and achieve an effective process of the life cycle of a single-family house, it is necessary to take care of its efficiency starting from the determination of needs and objectives and ending with the usage of a building.

  10. Indoor climate perceived as improved after energy retrofitting of single-family houses

    DEFF Research Database (Denmark)

    Knudsen, Henrik Nellemose; Jensen, Ole Michael

    2014-01-01

    The need for energy retrofitting of the Danish single-family houses is massive, especially for the high proportion of single-family houses built in the 1960s and 1970s. But even though the potential benefits are many, only few families embark on a major energy retrofit. There may be many reasons...... for this. An obvious one may be limited knowledge of non-energy benefits, e.g. in relation to the indoor climate. The objective of this study was to explain this limited effort to save energy by identifying barriers and incentives among house owners in relation to energy retrofitting of one’s own house....... Moreover, it was investigated among house owners, who had carried out energy retrofitting, whether a number of factors, including the perceived indoor climate, became better or worse after retrofitting. A questionnaire survey was carried out among 1,990 house owners in a municipality north of Copenhagen...

  11. Splitting Terraced Houses Into Single Units Using Oblique Aerial Imagery

    Science.gov (United States)

    Dahlke, D.

    2017-05-01

    This paper introduces a method to subdivide complex building structures like terraced houses into single house units comparable to units available in a cadastral map. 3D line segments are detected with sub-pixel accuracy in traditional vertical true orthomosaics as well as in innovative oblique true orthomosaics and their respective surface models. Hereby high gradient strengths on roofs as well as façades are taken into account. By investigating the coplanarity and frequencies within a set of 3D line segments, individual cut lines for a building complex are found. The resulting regions ideally describe single houses and thus the object complexity is reduced for subsequent topological, semantical or geometrical considerations. For the chosen study area with 70 buidling outlines a hit rate of 80% for cut lines is achieved.

  12. Full-service concept for energy efficient renovation of single-family houses

    DEFF Research Database (Denmark)

    Vanhoutteghem, Lies; Tommerup, Henrik M.; Svendsen, Svend

    2011-01-01

    the solutions. Such one-stop-shops in the form of full-service providers of energy efficient renovation of single-family house are missing in the Nordic countries, although this service is vital to open up the market. As part of the Nordic research project `SuccesFamilies´ with the purpose to change...... houses. A one-stop-shop in the form of a full-service concept could be seen as a possibility to make it easy for the homeowner to comply with possible future requirements to realize far-reaching energy savings in connection with extensive renovations, provided that the building sector offers...... includes an ideal full-service concept and technical renovation solutions targeted to different types of single-family houses....

  13. Single women and housing choices in urban Japan

    NARCIS (Netherlands)

    Ronald, R.; Nakano, L.

    2013-01-01

    Japan has experienced a particularly sharp decline in marriage in recent decades and a subsequent increase in ‘never-marrieds’ and single-person households. Social fragmentation has been associated with prolonged economic instability and neoliberalization that has restructured employment, housing

  14. Method for planning extensive energy renovation of detached single-family houses

    DEFF Research Database (Denmark)

    Grøn Bjørneboe, Matilde

    , and 22% occurs in single-family houses, making this the largest single contributor to the total consumption after road transport (DEA, 2015a). There is a large potential for achieving energy savings in this sector, especially among the large number of single-family houses built in the 1960s and 1970s...... that the use of this approach produced a better renovation with a larger energy saving. The initial evaluation helped the house owners identify a maintenance backlog, and the use of an independent advisor helped ensure quality throughout the process. Renovations are too often carried out for just one purpose......: maintenance, to update functions or to reduce energy consumption. But a lot can be gained by combining these efforts, which can reduce expenses for planning and execution and avoid doing things twice. Research for this thesis demonstrated this approach by carrying out a renovation based on maintenance...

  15. Transformation of the Housing Market in Tokyo since the Late 1990s: Housing Purchases by Single-person Households

    Directory of Open Access Journals (Sweden)

    Tomoko Kubo

    2011-12-01

    Full Text Available This study aims to clarify the correlation between the transformation of the Japanese housing market and the increasing number of single-person households in Japan, with a special focus on the supply of compact condominiums. In order to achieve the abovementioned purpose, the changes in the Japanese housing market and diversification of the Japanese household structure are described. Finally, the features of the supply strategies of condominium suppliers, which reflect the diversification of the household structure and increasing need for condominiums by single-person households in central Tokyo, are examined.

  16. 30 CFR 77.905 - Connection of single-phase loads.

    Science.gov (United States)

    2010-07-01

    ... COAL MINES Low- and Medium-Voltage Alternating Current Circuits § 77.905 Connection of single-phase loads. Single-phase loads shall be connected phase-to-phase in resistance grounded systems. ...

  17. 30 CFR 77.806 - Connection of single-phase loads.

    Science.gov (United States)

    2010-07-01

    ... COAL MINES Surface High-Voltage Distribution § 77.806 Connection of single-phase loads. Single-phase loads, such as transformer primaries, shall be connected phase to phase in resistance grounded systems. ...

  18. Thermal design of a modern, air-conditioned, single-floor, solar-powered desert house

    KAUST Repository

    Serag-Eldin, M. A.

    2011-12-01

    The paper presents a thermal analysis of a single-floor, solar-powered desert house. The house is air-conditioned and provides all modern comforts and facilities. Electrical power, which drives the entire energy system, is generated by roof-mounted photovoltaic modules. The modules are fixed on special cradles which fold at night to expose the roof to the night sky, thereby enhancing night-time cooling, which is substantial in the desert environment. A detailed dynamic heat transfer analysis is conducted for the building envelope, coupled with a solar radiation model. Application to a typical Middle-Eastern desert site reveals that indeed such a design is feasible with present-day technology; and should be even more attractive with future advances in technology. © 2011 Copyright Taylor and Francis Group, LLC.

  19. Low-Load Space Conditioning Needs Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Puttagunta, Srikanth [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2015-05-19

    Heating, ventilating, and air-conditioning (HVAC) equipment must be right-sized to ensure energy performance and comfort. With limited low-load options in the HVAC market, many new-construction housing units are being fitted with oversized equipment that creates system efficiency, comfort, and cost penalties. To bridge the gap between currently available HVAC equipment that is oversized or inefficient and the rising demand for low-load HVAC equipment in the marketplace, HVAC equipment manufacturers need to be fully aware of the needs of the multifamily building and attached single-family (duplex and townhouse) home market. Over the past decade, Steven Winter Associates, Inc. (SWA) has provided certification and consulting services for hundreds of housing projects and has accrued a large pool of data that describe multifamily and attached single-family home characteristics. The U.S. Department of Energy’s Building America research team Consortium for Advanced Residential Buildings (CARB) compiled and analyzed these data to outline the characteristics of low-load dwellings such as the heating and cooling design loads.

  20. Autonomous houses. Autonomous house

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, S. (Tokai University, Tokyo (Japan). Faculty of Engineering)

    1991-09-30

    Self-sufficiency type houses are outlined. On condition that people gain a certain amount of income in relation with the society, they self-suffice under the given environment, allowing themselves to accept a minimum of industrial products with small environmental load. Ordinary supply from outside of fossil energy and materials which depend on it is minimized. Types are classified into three: energy, energy materials and perfect self-sufficiency. A study project for environment symbiotic houses is progressing which is planned by the Ministry of Construction and Institute of Building Energy Conservation and is invested by a private company. Its target is making a house for halving an environmental load by CO{sub 2}, for the purpose of creating the environment symbiotic house which is nice to and in harmony with the global environment and human beings. As a part of the studies on energy-saving and resource conservation on houses, introduced is a plan of an autonomous house at Izu-Atagawa. The passive method and high thermal-insulation are used for air conditioning, and hot spring water for hot water supply. Electric power is generated by hydroelectric power generation using mountain streams and by solar cells. Staple food is purchased, while subsidiary food is sufficed. 17 refs., 4 figs., 1 tab.

  1. Effect of Environmental Enrichment on Singly- and Group-Housed Squirrel Monkeys

    Science.gov (United States)

    Spring, Sarah E.; Clifford, James O.; Tomko, David L.; Hargens, Alan R. (Technical Monitor)

    1996-01-01

    Nonhuman primates display an interest in novel places, habituate to new situations, and spend most of their daily activity in the wild in large groups engaging in feeding behaviors. Captivity changes these behaviors, and disrupts normal social hierarchies. In captivity, animals may exhibit stereotypical behaviors which are thought to indicate decreased psychological well-being (PWB). If an animal's behaviors can be made to approach those seen in the wild, and stereotypical behaviors are minimal it is assumed that PWB is adequate. Environmental enrichment (EE) devices have been used to address the Animal Welfare Act's requirement that the PWB of captive nonhuman primates be considered. The purpose of the present study was to examine whether various EE devices improve the PWB of captive squirrel monkeys. The present study used behavioral observation to quantify the effectiveness of several EE devices in reducing stereotypical behaviors in squirrel monkeys housed singly or in groups. Results showed that the EE devices used did not affect the expression of normal or stereotypical behaviors, but that the type of housing did.

  2. Energy Renovation of Danish Single-Family Houses

    DEFF Research Database (Denmark)

    Mortensen, Andrea

    2015-01-01

    . The results show that despite the barriers the owners can in fact be motivated to perform private energy renovations. A sound project economy is all-important for this to happen and it should if possible be supported by improvements in both comfort, indoor environment and architecture to increase......The PhD project is based on requirements from the European Union to reduce the energy consumption and on current renovation needs of and a huge energy saving potential in the Danish single-family houses from the 1960’s and 1970’s. The project focuses on the barriers for energy renovations...... of these houses and on defining motivation factors for the homeowners. The barriers are many and variating in influence and studies show that both professionals and homeowners are affected. The barriers range from lack of interest and knowledge to uncertainties about among others economy and technical solutions...

  3. Assessment of thermal load reduction due to the application of simple passive techniques in a house office building at the south of Libya

    International Nuclear Information System (INIS)

    Domanski, Roman; Azzain, Gassem

    2006-01-01

    The assessment of possible reduction of heating and cooling requirements of 300 m 2 house-office building has been presented in this paper, when simple Thermal Passive Techniques (TPT) have been applied to building's construction in Sebha city at the Libyan south. The known software for dynamic simulation (TRNSYS) has been used as an environment of digital experimentation for this study. A prototype represents the building has been constructed with the help of the available model of single thermal zone of TRNSYS (Type 19). The built-in ASHREA Transfer Function Method within this model has been used to calculate the heat flux through building's materials. Primarily, the thermal load on building's construction without TPTs has been evaluated under weather conditions of a Typical Meteorological Year (TMY) of Sebha city. Then, the building has been equipped with simple TPTs (such as the control of building materials, insulation, shading, infiltration and ventilation with windows resizing). This building was subjected to the same weather conditions and again the thermal load has been evaluated in order to report the percentage of reduction of thermal load. The simulation has been conducted successfully, where good assessment of reduction of annual heating and cooling demands in the building has been obtained. It is proved that, about (46%) of annual heating load and (48%) of annual cooling load can be reduced if suitable simple TPTs were incorporated in buildings.(Author)

  4. Simulation of control performance under house load transients for nuclear power plant

    International Nuclear Information System (INIS)

    Liao Zhongyue; Wang Yuanlong; Tang Yuyuan; Liu Jiong

    1999-01-01

    The CATIA2 code is used to simulate the extreme normal transients--house load transients of Qinshan Phase II 600 MW nuclear power plant. The simulating results show that all of the reactor main parameters are operating in the allowable ranges, the reactor system is stable, and the control characteristics of the nuclear power plant is satisfactory. They are also good in agreement with Framatome's results

  5. Fifth pathway in New Jersey. House officer preparatory course for US foreign medical graduates.

    Science.gov (United States)

    McGrough, W E

    1975-06-09

    The Fifth Channel in New Jersey is a Fifth Pathway program for US foreign medical graduates. In its third year, 83 percent of its 81 graduates are house officers at 18 US medical school-affiliated hospitals. Performance as house officers is characterized as competitive with peers, including US graduates. Positive attitudes toward work load, fellow workers, and patients compared with those of fellow house staff are noted. Quality of performance as house officers correlates most strongly with the change in mean scores of two batteries of clinical National Board examinations taken during the Fifth Pathway and less strongly with mean scores of single batteries of National Boards, Intelligence quotient, Educational Council for Foreign Medical Graduates (ECFMG) examination, ang age. Recommendations concerning the implementing of similar programs in other states are presented.

  6. Barriers for Energy Renovation of Danish Single-Family Houses and Suggested Solutions to Overcome These

    DEFF Research Database (Denmark)

    Mortensen, Andrea; Heiselberg, Per; Knudstrup, Mary-Ann

    2011-01-01

    As much as 40% of the total energy consumption in Denmark is utilized by the building sector and most of this energy is used for heating. Political initiatives have been taken to reduce this amount considerably but for this to happen, the energy consumption of the existing residential housing stock...... must be reduced dramatically. The greatest saving potential is found among the approximately 440.000 standardised single-family houses which were constructed in the 1960’s and 1970’s. It is found that barriers preventing the implementation of this great potential are present in various forms among all...

  7. Moisture supply in Danish single-family houses – the influence of building style

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan de Place; Møller, Eva B.

    2017-01-01

    According to ISO 13788 internal moisture supply in dwellings can be described by humidity classes defined by outdoor temperature, occupancy and ventilation. Hygrothermal measurements in 500 Danish single-family houses were made to investigate if building style and geographical location are import......According to ISO 13788 internal moisture supply in dwellings can be described by humidity classes defined by outdoor temperature, occupancy and ventilation. Hygrothermal measurements in 500 Danish single-family houses were made to investigate if building style and geographical location...

  8. Land cover in single-family housing areas and how it correlates with urban form

    DEFF Research Database (Denmark)

    Nielsen, Mette Boye; Jensen, Marina Bergen

    2015-01-01

    Land cover composition is a valuable indicator of the ecological performance of a city. Single-family housing areas constitute a substantial part of most cities and may as such play an important role for sustainable urban development. From aerial photos we performed detailed GIS-based mapping...... of land cover in three detached single-family housing areas in Denmark of different urban form but comparable housing densities (ranging from 10.0 to 11.3 houses per hectare). The findings were subjected to statistical analysis and landscape metrics. Land cover varied with urban form: A traditional...... spatial configuration with rectangular parcels contained significantly more vegetation and less impervious surfaces per parcel than newer Radburn-inspired configurations with more quadratic parcels. Correlation analysis showed size of paved access ways to be positively correlated with distance from road...

  9. Energy renovation of an old single-family house

    DEFF Research Database (Denmark)

    Overgaard, L.L.; Tommerup, Henrik M.; Svendsen, Svend

    2005-01-01

    After having identified a large potential for profitable energy renovation of the existing building stock, a demonstration project was carried out in practice. This paper deals with the methods and results from the demonstration project concerning a 161 m² poorly insulated single-family house built...... saving improvements carried out in the project are “easy to carry out” and cost-beneficial measures such as cavity wall insulation, loft insulation, insulation of walls under windows and a new second window-frame with energy-saving glass. The work was carried out by professional contractors at a total......). If a conservative way of financing the building work of 157,000 DKK is assumed, the first year’s cost equals DKK 8,500 and the house owner will gain a net saving the first year of DKK 7,500....

  10. Housing Stability among Homeless Individuals with Serious Mental Illness Participating in Housing First Programs

    Science.gov (United States)

    Pearson, Carol; Montgomery, Ann Elizabeth; Locke, Gretchen

    2009-01-01

    This article presents findings from an exploratory study of three programs using the Housing First approach to provide permanent supportive housing for single, homeless adults with serious mental illness and often co-occurring substance-related disorders. This approach provides direct, or nearly direct, access to housing that is intended to be…

  11. Two semidetached single family houses in Prague

    OpenAIRE

    DIEGO JOVELLS, FERNANDO JOSÉ

    2015-01-01

    Trabajo Fin de Grado de modalidad Intercambios Académicos. České Vysoké Učení Technické v Praze | Czech Technical University in Prague [en] This Bachelor’s Thesis is intent on building a single family house in Veleslavín, a district of Prague, part of Prague 6, situated in the west of the city. The chosen foundations, the structure, the installations of electricity, cold and hot water, heating system, and sanitation network are going to be studied in this project. Some plans will be done, ...

  12. Risk Assessment of Heating, Ventilating, and Air-Conditioning Strategies in Low-Load Homes

    Energy Technology Data Exchange (ETDEWEB)

    Poerschke, Andrew [IBACOS, Inc., Pittsburgh, PA (United States)

    2016-02-17

    "Modern, energy efficient homes conforming to the Zero Energy Ready Home standard face the challenge of meeting high customer expectations for comfort. Traditional heating, ventilation, and air conditioning (HVAC) sizing and control strategies may be insufficient to adequately condition each zone due to unique load patterns in each room caused by a number of factors. These factors include solar heat gains, occupant-related gains, and gains associated with appliances and electronics. Because of shrinking shell loads, these intermittent factors are having an increasingly significant impact on the thermal load in each zone. Consequently, occupant comfort can be compromised. To evaluate the impact of climate and house geometry, as well as HVAC system and control strategies on comfort conditions, IBACOS analyzed the results of 99 TRNSYS multiple-zone simulations. The results of this analysis indicate that for simple-geometry and single-story plans, a single zone and thermostat can adequately condition the entire house. Demanding house geometry and houses with multiple stories require the consideration of multiple thermostats and multiple zones.

  13. Load compensation for single phase system using series active filter ...

    African Journals Online (AJOL)

    Load compensation for single phase system using series active filter. ... KK Mishra, R Gupta ... load varies from time to time, the non linear load ranging from voltage source type harmonic load (VSHL) dominant to current source type harmonic ...

  14. Single-source mechanical loading system produces biaxial stresses in cylinders

    Science.gov (United States)

    Flower, J. F.; Stafford, R. L.

    1967-01-01

    Single-source mechanical loading system proportions axial-to-hoop tension loads applied to cylindrical specimens. The system consists of hydraulic, pneumatic, and lever arrangements which produce biaxial loading ratios.

  15. Theoretical overview of heating power and necessary heating supply temperatures in typical Danish single-family houses from the 1900s

    DEFF Research Database (Denmark)

    Østergaard, Dorte Skaarup; Svendsen, Svend

    2016-01-01

    in typical Danish single-family houses constructed in the 1900s. The study provides a simplified theoretical overview of typical building constructions and standards for the calculation of design heat loss and design heating power in Denmark in the 1900s. The heating power and heating demand in six typical...... Danish single-family houses constructed in the 1900s were estimated based on simple steady-state calculations. We found that the radiators in existing single-family houses should not necessarilrbe expected to be over-dimensioned compared to current design heat loss. However, there is considerable...... potential for using low-temperature space heating in existing single-family houses in typical operation conditions. Older houses were not always found to require higher heating system temperatures than newer houses. We found that when these houses have gone through reasonable energy renovations, most...

  16. An Investigation of Energy Storage Possibilities in Single Family Houses for Smart Grid Purposes

    DEFF Research Database (Denmark)

    Andersen, Palle; Pedersen, Tom S.; Nielsen, Kirsten M.

    2014-01-01

    In Denmark it will be a challenge in near future to balance the electrical grid due to a large increase in the renewable energy production mainly from wind turbines. Smart grid solutions which exploit all storage capacities are essential to meet this challenge. In this work single family houses...... with heat pumps and floor heating are investigated for storage capability. The aim is to shift energy consumption a few hours in time to mitigate the effect of fluctuating production from wind and other renewable energy sources on the grid. Based on measurements in six inhabited houses for approximately...... a year prediction models are analysed. The main topic of this work is to investigate how behaviour of inhabitants affect the quality of predictions. Unfortunately the output of the models for single inhabited single family houses seems to give large standard deviations of the predictions, and aggregated...

  17. Cold Storage for a Single-Family House in Italy

    Directory of Open Access Journals (Sweden)

    Luigi Mongibello

    2016-12-01

    Full Text Available This work deals with the operation, modeling, simulation, and cost evaluation of two different cold storage systems for a single-family house in Italy, that differ from one another on the cold storage material. The two materials used to perform the numerical simulations of the cold storage systems are represented by cold water and a phase change material (PCM, and the numerical simulations have been realized by means of numerical codes written in Matlab environment. The main finding of the present work is represented by the fact that, for the considered user characteristics, and under the Italian electricity tariff policy, the use of a proper designed cold storage system characterized by an effective operation strategy could represent a viable solution from an economical point of view.

  18. To stay or to go? Postretirement housing choices of single Baby Boomer women.

    Science.gov (United States)

    Kopanidis, Foula Z; Robinson, Linda J; Reid, Mike

    2017-01-01

    Single women of the Baby Boomer generation are often financially disadvantaged in the retirement planning process due to their lower accumulated savings compared to male retirees. This disadvantage impacts significant consumption decisions such as postretirement housing choices. This study uses the theory of planned behavior to examine how certainty in intentions influences preparing and planning for postretirement housing. A typology of single Baby Boomer women is developed based on their financial, demographic, and psychological circumstances. Each segment likely requires different informational strategies and financial services to foster proactive planning for retirement. Significant implications exist for social policy and the financial services sector.

  19. 75 FR 4100 - Affirmative Fair Housing, Marketing (AFHM) Plan-Multifamily Housing, Affirmative Fair Housing...

    Science.gov (United States)

    2010-01-26

    ... DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT [Docket No. FR-5376-N-01] Affirmative Fair Housing, Marketing (AFHM) Plan-Multifamily Housing, Affirmative Fair Housing Marketing (AFHM) Plan-Single Family Housing and Affirmative Fair Housing Marketing (AFHM) Plan- Cooperatives/Condominiums AGENCY: Office of...

  20. A controlled intervention study concerning the effect of intended temperature rise on house dust mite load

    DEFF Research Database (Denmark)

    Sidenius, Kirsten E; Hallas, Thorkil E; Poulsen, Lars K.

    2002-01-01

    In epidemiological studies, increased indoor temperature--producing a lower relative humidity--is associated with low house dust mite (HDM) load. Twenty-eight dwellings were allocated for either intervention (12/15 completed) or control (11/13 completed). In the intervention group, participants w...

  1. Housing Resources and Programs for Single Student Parents at Community and Technical Colleges. Fact Sheet #C396

    Science.gov (United States)

    Thorman, Abby; Otto, Jessica; Gunn-Wright, Rhiana

    2012-01-01

    Parents with dependent children now make up almost one in four students pursuing higher education in the United States (Miller, Gault, and Thorman 2011). Single parents face particular challenges pursuing higher education, including securing safe and affordable housing. Single mothers often must spend over half of their income on housing expenses,…

  2. Investigations of Intelligent Solar Heating Systems for Single Family House

    DEFF Research Database (Denmark)

    Andersen, Elsa; Chen, Ziqian; Fan, Jianhua

    2014-01-01

    Three differently designed intelligent solar heating systems are investigated experimentally in a test facility. The systems provide all the needed yearly heating demand in single family houses. The systems are based on highly stratified tanks with variable auxiliary heated volumes. The tank is a......, the control strategy of intelligent solar heating systems is investigated and the yearly auxiliary energy use of the systems and the electricity price for supplying the consumers with domestic hot water and space heating are calculated....... systems.The system will be equipped with an intelligent control system where the control of the electrical heating element(s)/heat pump is based on forecasts of the variable electricity price, the heating demand and the solar energy production.By means of numerical models of the systems made in Trnsys......Three differently designed intelligent solar heating systems are investigated experimentally in a test facility. The systems provide all the needed yearly heating demand in single family houses. The systems are based on highly stratified tanks with variable auxiliary heated volumes. The tank...

  3. Modelling of Vortex-Induced Loading on a Single-Blade Installation Setup

    DEFF Research Database (Denmark)

    Skrzypinski, Witold Robert; Gaunaa, Mac; Heinz, Joachim Christian

    2016-01-01

    the same procedure. The reference time series were significantly different, depending on the inflow angle. This made the modelling of all the time series with a single and relatively simple engineering model challenging. In order to find model parameters, optimizations were carried out, based on the root-mean-square......Vortex-induced integral loading fluctuations on a single suspended blade at various inflow angles were modeled in the presents work by means of stochastic modelling methods. The reference time series were obtained by 3D DES CFD computations carried out on the DTU 10MW reference wind turbine blade...... varied depending on the inflow angle. None the less, the modelled and reference time series showed a satisfactory general agreement in terms of their visual and frequency characteristics. This indicated that the proposed method is suitable to model loading fluctuations on suspended blades....

  4. Development of an air heating system for single family housing

    DEFF Research Database (Denmark)

    Afshari, Alireza; Gunner, Amalie; Nikolaisen, Christian Grønborg

    2017-01-01

    The initial objective of the project was to break with common thinking about Space heating and to document that air heating can be used as the sole source of heating in a single Family house. The basic idea is that the ventilation must be installed in any case and it may equally well form the heat...

  5. Inventorying Toronto's single detached housing stocks to examine the availability of clay brick for urban mining.

    Science.gov (United States)

    Ergun, Deniz; Gorgolewski, Mark

    2015-11-01

    This study examines the stocks of clay brick in Toronto's single detached housing, to provide parameters for city scale material reuse and recycling. Based on consensus from the literature and statistics on Toronto's single detached housing stocks, city scale reusable and recyclable stocks were estimated to provide an understanding of what volume could be saved from landfill and reintroduced into the urban fabric. On average 2523-4542 m(3) of brick was determined to be available annually for reuse, which would account for 20-36% of the volume of virgin brick consumed in new house construction in 2012. A higher volume, 6187 m(3) of brick, was determined to be available annually for recycling because more of the prevalence of cement-based mortar, which creates challenges for brick reuse in Toronto. The results demonstrated that older housing containing reusable brick were being mostly landfilled and replaced with housing that contained only recyclable brick. Copyright © 2015 Elsevier Ltd. All rights reserved.

  6. Initial transformer sizing for single-phase residential load

    International Nuclear Information System (INIS)

    Schneider, K.C.; Hoad, R.F.

    1992-01-01

    The purchase of distribution transformers represents a significant capital investment per year for an electric utility. Choosing the correct thermal and economic size transformer can help control this investment. This paper describes a method for determining the correct economic size of distribution transformers using end-use appliance load profiles and the ANSI/IEEE Standard C57.91-1981 thermal model. Although applied only to single family and multifamily residential load in this paper, the method can be extended to other types of load such as commercial or industrial

  7. Energy Efficiency Potential in the U.S. Single-Family Housing Stock

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, Eric J. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Christensen, Craig B. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Horowitz, Scott G. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Robertson, Joseph J. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Maguire, Jeffrey B. [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-12-19

    Typical approaches for assessing energy efficiency potential in buildings use a limited number of prototypes, and therefore suffer from inadequate resolution when pass-fail cost-effectiveness tests are applied, which can significantly underestimate or overestimate the economic potential of energy efficiency technologies. This analysis applies a new approach to large-scale residential energy analysis, combining the use of large public and private data sources, statistical sampling, detailed building simulations, and high-performance computing to achieve unprecedented granularity - and therefore accuracy - in modeling the diversity of the single-family housing stock. The result is a comprehensive set of maps, tables, and figures showing the technical and economic potential of 50 plus residential energy efficiency upgrades and packages for each state. Policymakers, program designers, and manufacturers can use these results to identify upgrades with the highest potential for cost-effective savings in a particular state or region, as well as help identify customer segments for targeted marketing and deployment. The primary finding of this analysis is that there is significant technical and economic potential to save electricity and on-site fuel use in the single-family housing stock. However, the economic potential is very sensitive to the cost-effectiveness criteria used for analysis. Additionally, the savings of particular energy efficiency upgrades is situation-specific within the housing stock (depending on climate, building vintage, heating fuel type, building physical characteristics, etc.).

  8. Dynamic strength of rock with single planar joint under various loading rates at various angles of loads applied

    Directory of Open Access Journals (Sweden)

    Pei-Yun Shu

    2018-06-01

    Full Text Available Intact rock-like specimens and specimens that include a single, smooth planar joint at various angles are prepared for split Hopkinson pressure bar (SHPB testing. A buffer pad between the striker bar and the incident bar of an SHPB apparatus is used to absorb some of the shock energy. This can generate loading rates of 20.2–4627.3 GPa/s, enabling dynamic peak stresses/strengths and associated failure patterns of the specimens to be investigated. The effects of the loading rate and angle of load applied on the dynamic peak stresses/strengths of the specimens are examined. Relevant experimental results demonstrate that the failure pattern of each specimen can be classified as four types: Type A, integrated with or without tiny flake-off; Type B, slide failure; Type C, fracture failure; and Type D, crushing failure. The dynamic peak stresses/strengths of the specimens that have similar failure patterns increase linearly with the loading rate, yielding high correlations that are evident on semi-logarithmic plots. The slope of the failure envelope is the smallest for slide failure, followed by crushing failure, and that of fracture failure is the largest. The magnitude of the plot slope of the dynamic peak stress against the loading rate for the specimens that are still integrated after testing is between that of slide failure and crushing failure. The angle of application has a limited effect on the dynamic peak stresses/strengths of the specimens regardless of the failure pattern, but it affects the bounds of the loading rates that yield each failure pattern, and thus influences the dynamic responses of the single jointed specimen. Slide failure occurs at the lowest loading rate of any failure, but can only occur in single jointed specimen that allows sliding. Crushing failure is typically associated with the largest loading rate, and fracture failure may occur when the loading rate is between the boundaries for slide failure and crushing

  9. Load dependency in force-length relations in isolated single cardiomyocytes.

    Science.gov (United States)

    Iribe, Gentaro; Kaneko, Toshiyuki; Yamaguchi, Yohei; Naruse, Keiji

    2014-08-01

    The previously reported pressure-volume (PV) relationship in frog hearts shows that end-systolic PV relation (ESPVR) is load dependent, whereas ESPVR in canine hearts is load independent. To study intrinsic cardiac mechanics in detail, it is desirable to study mechanics in a single isolated cardiomyocyte that is free from interstitial connective tissue. Previous single cell mechanics studies used a pair of carbon fibers (CF) attached to the upper surface of opposite cell ends to stretch cells. These studies showed that end-systolic force-length (FL) relation (ESFLR) is load independent. However, the range of applicable mechanical load using the conventional technique is limited because of weak cell-CF attachment. Therefore, the behavior of ESFLR in single cells under physiologically possible conditions of greater load is not yet well known. To cover wider loading range, we contrived a new method to hold cell-ends more firmly using two pairs of CF attached to both upper and bottom surfaces of cells. The new method allowed stretching cells to 2.2 μm or more in end-diastolic sarcomere length. ESFLR virtually behaves in a load independent manner only with end-diastolic sarcomere length less than 1.95 μm. It exhibited clear load dependency with higher preload, especially with low afterload conditions. Instantaneous cellular elastance curves showed that decreasing afterload enhanced relaxation and slowed time to peak elastance, as previously reported. A simulation study of a mathematical model with detailed description of thin filament activation suggested that velocity dependent thin filament inactivation is crucial for the observed load dependent behaviors and previously reported afterload dependent change in Ca(2+) transient shape. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Social anthropological and interdisciplinary research on the conversion of electrically heated single family houses to heating by combined pellet-solar systems

    International Nuclear Information System (INIS)

    Henning, Annette

    2004-01-01

    The social anthropological research presented here is part of the interdisciplinary research project PESTO, which focuses on the (partial or complete) conversion of single family houses from electric heating to heating by combined pellet-solar heating systems. Basic to this research is the assumption that it is more likely that energy conversions are carried through, and that they are successful on a long-term basis, if the new products are designed to fit as well as possible into the everyday lives of people. The anthropological interest in the project can be divided into two parts; motives for or against a conversion among men and women in Swedish households, and product design and placement in (previously) electrically heated single-family houses. Literature studies and semi-structured qualitative interviews are the main methods used in the anthropological part of the project. During the next 3-year project period, these investigations will be used to support information and marketing, and to formulate recommendations for conversion practice of electrically heated single-family houses to combined pellet-solar heating. (Author)

  11. In-house L-band niobium single cell cavities at KEK

    International Nuclear Information System (INIS)

    Inoue, Hitoshi; Kobayashi, Yoshiharu; Funahashi, Yoshisato; Koizumi, Susumu; Saito, Kenji; Noguchi, Shuichi; Kako, Eiji; Shishido, Toshio

    1993-01-01

    For the TESLA (TeV Energy Superconducting Linear Accelerator) as an energy frontier accelerator of the next generation improving the performance of the niobium superconducting cavities is the most important issue and much reduction of fabrication cost of cavities is another key. Since manufacturing of niobium material requires hard techniques due to the easily oxidizable metal, fabrication of niobium cavities has been conducted in only companies providing enough equipments in Japan. KEK has accumulated the fabrication technics such as forming method by deep drawing, trimming, centering of beam tubes, electron beam welding and measurement of manufacturing error so on. We made in-house L-band single cell cavities using these technologies. In this paper we present these manufacturing of the niobium cavities and estimate the fabrication cost as exactly as possible. The manufacturing error is also described. (author)

  12. Controlled nanostructure and high loading of single-walled carbon nanotubes reinforced polycarbonate composite

    International Nuclear Information System (INIS)

    Wang Shiren; Liang Zhiyong; Pham, Giang; Park, Young-Bin; Wang, Ben; Zhang, Chuck; Kramer, Leslie; Funchess, Percy

    2007-01-01

    This paper presents an effective technique to fabricate thermoplastic nanocomposites with high loading of well-dispersed single-walled carbon nanotubes (SWNTs). SWNT membranes were made from a multi-step dispersion and filtration method, and then impregnated with polycarbonate solution to make thermoplastic nanocomposites. High loading of nanotubes was achieved by controlling the viscosity of polycarbonate solution. SEM and AFM characterization results revealed the controlled nanostructure in the resultant nanocomposites. Dynamic mechanical property tests indicated that the storage modulus of the resulting nanocomposites at 20 wt% nanotubes loading was improved by a factor of 3.4 compared with neat polycarbonate material. These results suggest the developed approach is an effective way to fabricate thermoplastic nanocomposites with good dispersion and high SWNT loading

  13. Smart Growth and the Challenge of Nimby: Multifamily Dwellings and their Association with Single-Family House Selling Prices in Tallahasse, Florida, USA

    Directory of Open Access Journals (Sweden)

    Huston GIBSON

    2013-06-01

    Full Text Available Citizens protest development when they consider it undesirable. One type of development commonly perceived as undesirable by single-family home owners is proximate multifamily housing, often considered a cause of property devaluation. This study assesses multifamily housing, by typology, and its monetary association with proximate single-family housing prices. The research design is a cross-sectional study using multivariate regression. The unit of analysis is the detached single-family dwelling. The study population is a sample taken from all arms-length owner-occupied, primary residence, detached single-family property transactions recorded in Tallahassee-Leon County, Florida, USA, during 2008. The key findings show no statistically significant negative associations between multifamily housing and single-family property selling prices in the sample; in fact, the two were positively correlated. These findings address single-family homeowner concerns about proximate multifamily housing and should bolster the political feasibility of Smart Growth policy, which recommends denser urban infill.

  14. Cold Storage for a Single-Family House in Italy

    OpenAIRE

    Luigi Mongibello; Giorgio Graditi

    2016-01-01

    This work deals with the operation, modeling, simulation, and cost evaluation of two different cold storage systems for a single-family house in Italy, that differ from one another on the cold storage material. The two materials used to perform the numerical simulations of the cold storage systems are represented by cold water and a phase change material (PCM), and the numerical simulations have been realized by means of numerical codes written in Matlab environment. The main finding of the p...

  15. Building America Case Study: The Impact of Thermostat Placement in Low-Load Homes in Sunny Climates, Denver, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    2016-02-01

    Modern, energy-efficient homes conforming to the Zero Energy Ready Home standard face the challenge of meeting high customer expectations for comfort. Traditional heating, ventilation, and air conditioning (HVAC) sizing and control strategies may be insufficient to adequately condition each zone due to unique load patterns in each room caused by a number of factors. These factors include solar heat gains, occupant-related gains, and gains associated with appliances and electronics. Because of shrinking shell loads, these intermittent factors are having an increasingly significant impact on the thermal load in each zone. Consequently, occupant comfort can be compromised. To evaluate the impact of climate and house geometry, as well as HVAC system and control strategies on comfort conditions, IBACOS analyzed the results of 99 TRNSYS multiple-zone simulations. The results of this analysis indicate that for simple-geometry and single-story plans, a single zone and thermostat can adequately condition the entire house. Demanding house geometry and houses with multiple stories require the consideration of multiple thermostats and multiple zones.

  16. Pesticides Present in Migrant Farmworker Housing in North Carolina

    Science.gov (United States)

    Arcury, Thomas A.; Lu, Chensheng; Chen, Haiying; Quandt, Sara A.

    2014-01-01

    Background Migrant farmworkers are exposed to pesticides at work. Housing provided to migrant farmworkers may also expose them to pesticides, increasing their health risks. This analysis (1) describes the presence of organophosphorous (OP) and pyrethroid pesticides in North Carolina migrant farmworker houses, and (2) delineates associations of farmworker camp characteristics with pesticide detection and concentration. Methods In 2010, 186 migrant farmworkers camps in NC were recruited (participation rate of 82.3%); pesticide wipe samples for 176 houses were analyzed. Tobacco is the predominant hand-harvested crop in this region. Two farmworkers per camp completed interviews; a third assisted with a housing inspection. Gas chromatography–mass spectrometry was used to detect OP and pyrethroid pesticides. Covariates of pesticide detection and concentration were determined with ANOVA and Tobit regression. Results OPs were found in 166 of 176 houses (average of 2.4/house); pyrethroids were found in 171 houses (average of 4.3/house). The number of different OPs detected in each camp and concentrations of these OPs were not associated with camp and housing characteristics. The number of different pyrethroids detected in each camp and concentrations of these pyrethroids were associated with camps having residents with H2-A visas, a posted North Carolina Department of Labor Certificate of Inspection, no barracks, fewer residents, no bedroom weather protection or floor violations, and no roaches. Conclusions Farmworkers are exposed to pesticides where they live. Policy on removing pesticides from farmworker houses is needed. Reducing pesticides in farmworker houses will reduce one health risk confronted by this vulnerable population. PMID:24038176

  17. Analyzing Design Heating Loads in Superinsulated Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Arena, Lois [Consortium for Advanced Residential Buildings, Norwalk, CT (United States)

    2015-06-16

    The U.S. Department of Energy’s Building America research team Consortium for Advanced Residential Buildings (CARB) worked with the EcoVillage cohousing community in Ithaca, New York, on the Third Residential EcoVillage Experience neighborhood. This communityscale project consists of 40 housing units—15 apartments and 25 single-family residences. Units range in size from 450 ft2 to 1,664 ft2 and cost from $80,000 for a studio apartment to $235,000 for a three- or four-bedroom single-family home. For the research component of this project, CARB analyzed current heating system sizing methods for superinsulated homes in cold climates to determine if changes in building load calculation methodology should be recommended. Actual heating energy use was monitored and compared to results from the Air Conditioning Contractors of America’s Manual J8 (MJ8) and the Passive House Planning Package software. Results from that research indicate that MJ8 significantly oversizes heating systems for superinsulated homes and that thermal inertia and internal gains should be considered for more accurate load calculations.

  18. A fully packaged micromachined single crystalline resonant force sensor

    Energy Technology Data Exchange (ETDEWEB)

    Cavalloni, C.; Gnielka, M.; Berg, J. von [Kistler Instrumente AG, Winterthur (Switzerland); Haueis, M.; Dual, J. [ETH Zuerich, Inst. of Mechanical Systems, Zuerich (Switzerland); Buser, R. [Interstate Univ. of Applied Science Buchs, Buchs (Switzerland)

    2001-07-01

    In this work a fully packaged resonant force sensor for static load measurements is presented. The working principle is based on the shift of the resonance frequency in response to the applied load. The heart of the sensor, the resonant structure, is fabricated by micromachining using single crystalline silicon. To avoid creep and hysteresis and to minimize temperature induced stress the resonant structure is encapsulated using an all-in-silicon solution. This means that the load coupling, the excitation of the microresonator and the detection of the oscillation signal are integrated in only one single crystalline silicon chip. The chip is packaged into a specially designed housing made of steel which has been designed with respect to application in harsh environments. The unloaded sensor has an initial frequency of about 22,5 kHz. The sensitivity amounts to 26 Hz/N with a linearity error significantly less than 0,5%FSO. (orig.)

  19. Load compensation for single phase system using series active filter

    African Journals Online (AJOL)

    user

    Keywords: Active power filter (APF), current source type of harmonic load ... Single phase active filters could attract less attention than three phase due to its low ..... Generalised single-phase p-q theory for active power filtering: simulation and.

  20. Effects of noise and task loading on a communication task loading on a communication task

    Science.gov (United States)

    Orrell, Dean H., II

    Previous research had shown the effect of noise on a single communication task. This research has been criticized as not being representative of a real world situation since subjects allocated all of their attention to only one task. In the present study, the effect of adding a loading task to a standard noise-communication paradigm was investigated. Subjects performed both a communication task (Modified Rhyme Test; House et al. 1965) and a short term memory task (Sternberg, 1969) in simulated levels of aircraft noise (95, 105 and 115 dB overall sound pressure level (OASPL)). Task loading was varied with Sternberg's task by requiring subjects to memorize one, four, or six alphanumeric characters. Simulated aircraft noise was varied between levels of 95, 105 and 115 dB OASPL using a pink noise source. Results show that the addition of Sternberg's task and little effect on the intelligibility of the communication task while response time for the communication task increased.

  1. Immediate Loading of Single Implants in the Anterior Maxilla: A 1-Year Prospective Clinical Study on 34 Patients

    Directory of Open Access Journals (Sweden)

    Miguel Stanley

    2017-01-01

    Full Text Available Purpose. To present the outcomes of immediately loaded single implants placed in the anterior maxilla. Methods. Over a 2-year period, all patients referred to a private clinic were considered for enrolment in this study. Inclusion criteria were single-tooth placement in postextraction sockets or healed sites of the anterior maxilla. All implants were immediately loaded and followed for a period of 1 year after the placement of definitive crowns. The outcome measures were implant stability, survival, and success. Results. 34 patients were selected and 43 tapered implants with a knife-edge thread design and a nanostructured, calcium-incorporated surface (Anyridge®, Megagen, Gyeongsang, Korea were installed. Two implants were not sufficiently stable at placement (ISQ < 60 and were considered failed for immediate loading; 41 implants had an ISQ ≥ 60 at placement and were immediately loaded. One year after the placement of definitive crowns, no implant failures were reported, for a survival rate of 100%. No biological complications were found, but 2 implants had their prosthetic abutments loosened: the implant success rate was 95.2%. Conclusions. In the present study on the immediate loading of single implants in the anterior maxilla, positive outcomes were reported, with high survival (100% and success (95.2% rates (the present study has been registered in the ISRCTN registry, a publicly available trial register recognized by WHO and ICMJE, with number ISRCTN12935478.

  2. Properties of single-walled carbon nanotube-based aerogels as a function of nanotube loading

    International Nuclear Information System (INIS)

    Worsley, Marcus A.; Pauzauskie, Peter J.; Kucheyev, Sergei O.; Zaug, Joseph M.; Hamza, Alex V.; Satcher, Joe H.; Baumann, Theodore F.

    2009-01-01

    Here, we present the synthesis and characterization of low-density single-walled carbon nanotube-based aerogels (SWNT-CA). Aerogels with varying nanotube loading (0-55 wt.%) and density (20-350 mg cm -3 ) were fabricated and characterized by four-probe method, electron microscopy, Raman spectroscopy and nitrogen porosimetry. Several properties of the SWNT-CAs were highly dependent upon nanotube loading. At nanotube loadings of 55 wt.%, shrinkage of the aerogel monoliths during carbonization and drying was almost completely eliminated. Electrical conductivities are improved by an order of magnitude for the SWNT-CA (55 wt.% nanotubes) compared to those of foams without nanotubes. Surface areas as high as 184 m 2 g -1 were achieved for SWNT-CAs with greater than 20 wt.% nanotube loading.

  3. 75 FR 11553 - Final Fair Market Rents for the Housing Choice Voucher Program and Moderate Rehabilitation Single...

    Science.gov (United States)

    2010-03-11

    ... provided on the same website noted above. Any questions related to use of FMRs or voucher payment standards... the Housing Choice Voucher Program and Moderate Rehabilitation Single Room Occupancy Program for... County, ND. Both areas were having significant problems administering the Housing Choice Voucher program...

  4. Business models for full service energy renovation of single-family houses in Nordic countries

    International Nuclear Information System (INIS)

    Mahapatra, Krushna; Gustavsson, Leif; Haavik, Trond; Aabrekk, Synnøve; Svendsen, Svend; Vanhoutteghem, Lies; Paiho, Satu; Ala-Juusela, Mia

    2013-01-01

    Highlights: ► In the Nordic countries there is significant primary energy saving potential in single-family houses from 1970s. ► There are several behavioral, economical and market related hindrances to adoption of energy efficiency measures. ► One-stop-shop business models to offer full service energy renovation packages are slowly emerging. ► Marketing strategies and policy measures are required to promote full service energy renovation of single-family house. - Abstract: In Nordic countries significant primary energy saving potential exists in houses built before 1980. These old houses need to be renovated, which provides an opportunity for implementation of energy efficiency measures. However, there are several economic and market hindrances and the renovation markets are dominated by handicraft-based individual solutions. In this paper we have analyzed the opportunities for implementation of one-stop-shop business models where an overall contractor offers full-service renovation packages including consulting, independent energy audit, renovation work, follow-up (independent quality control and commissioning) and financing. A comparative assessment of emerging business models in the Nordic countries shows that different types of actors can provide such a service. Financing is included in some models. There are differences in how customers are contacted, while the similarities are on how the service is provided. Even though there is strong business potential for one-stop-shop energy renovation concept, still it has been somewhat difficult to start or run such a business. Various options to overcome the hindrances to promote energy efficient renovation of detached houses are discussed

  5. Early Loaded Single Implant Reinforced Mandibular Overdenture

    Directory of Open Access Journals (Sweden)

    K. Nischal

    2016-01-01

    Full Text Available Rehabilitating atrophied mandible with two-implant supported denture is a common treatment modality for implant retained removable overdenture in mandible. This paper aims to design a treatment modality where single implant reinforced overdenture is fabricated for a severely atrophied mandibular ridge with early loading protocol. Results of studies have shown that a single implant mandibular overdenture significantly increases the satisfaction and quality of life of patients with edentulism. Midline fracture of the prosthesis is the most common complication related to single implant and two-implant retained mandibular overdentures. To manage such complication, a thin metal mesh is used to reinforce the overdenture and also to make the prostheses lighter and cost effective as compared to conventional cast metal framework.

  6. State of inertia: psychological preparation of single Australian and UK baby boomer women for retirement housing change.

    Science.gov (United States)

    Kopanidis, Foula Z; Robinson, Linda J; Reid, Mike

    2014-01-01

    The transition into retirement is an important life phase that presents significant challenges in respect to well-being, lifestyle, and consumption choices. This article examines the consumption context of housing after retirement, in particular for the low-resourced cohort of single baby boomer women. Utilizing an extended Theory of Planned Behavior model, we examine the relationship between intention and actual behavior, in this case financial advice seeking, as an important component of the psychological preparedness of single female baby boomer women. Our analysis showed both Australian and UK single baby boomer women display different behaviors in terms of seeking advice and their mental preparedness to adjust to a change in their living arrangements. The findings are discussed in terms of their implications for policy and further research.

  7. Functional adaptation to loading of a single bone is neuronally regulated and involves multiple bones.

    Science.gov (United States)

    Sample, Susannah J; Behan, Mary; Smith, Lesley; Oldenhoff, William E; Markel, Mark D; Kalscheur, Vicki L; Hao, Zhengling; Miletic, Vjekoslav; Muir, Peter

    2008-09-01

    Regulation of load-induced bone formation is considered a local phenomenon controlled by osteocytes, although it has also been hypothesized that functional adaptation may be neuronally regulated. The aim of this study was to examine bone formation in multiple bones, in response to loading of a single bone, and to determine whether adaptation may be neuronally regulated. Load-induced responses in the left and right ulnas and humeri were determined after loading of the right ulna in male Sprague-Dawley rats (69 +/- 16 days of age). After a single period of loading at -760-, -2000-, or -3750-microepsilon initial peak strain, rats were given calcein to label new bone formation. Bone formation and bone neuropeptide concentrations were determined at 10 days. In one group, temporary neuronal blocking was achieved by perineural anesthesia of the brachial plexus with bupivicaine during loading. We found right ulna loading induces adaptive responses in other bones in both thoracic limbs compared with Sham controls and that neuronal blocking during loading abrogated bone formation in the loaded ulna and other thoracic limb bones. Skeletal adaptation was more evident in distal long bones compared with proximal long bones. We also found that the single period of loading modulated bone neuropeptide concentrations persistently for 10 days. We conclude that functional adaptation to loading of a single bone in young rapidly growing rats is neuronally regulated and involves multiple bones. Persistent changes in bone neuropeptide concentrations after a single loading period suggest that plasticity exists in the innervation of bone.

  8. Using a One-Stop-Shop Concept to Guide Decisions when Single-Family Houses are renovated

    DEFF Research Database (Denmark)

    Grøn Bjørneboe, Matilde; Svendsen, Svend; Heller, Alfred

    2017-01-01

    of renovation. The scope of the project was to carry out renovations on up to three houses. The project revealed that the concept on its own was not enough to motivate the house owners to engage in extensive renovation. However, interviews with the house owners indicated that the renovations that took place had...... was to determine how a one-stop-shop (OSS) or full-service concept could be used to guide the extensive energy renovation of single-family houses. The purpose was partly to identify the benefits and disadvantages of using the concept and partly to evaluate the potential of the OSS concept for increasing the degree...... probably been expanded and improved with the use of the concept and that the renovations in general benefitted from an independent adviser....

  9. Different heating systems for single family house: Energy and economic analysis

    Directory of Open Access Journals (Sweden)

    Turanjanin Valentina M.

    2016-01-01

    Full Text Available The existing building stock energy consumption accounts for about 38% of final energy consumption in Republic of Serbia. 70% of that energy is consumed by residential sector, mostly for space heating. This research is addressed to the single family house building placed in the Belgrade city. The house has ground and first floor with total heating area of 130 m2 and pellet as space heating source. The aim of this paper is to evaluate energy and economic analysis for different heating systems. Several homeheating were compared: Option 1 (biomass combustion boiler using pellet as a fuel, Option 2 (gas combustion boiler and Option 3 (heat pump. The building performance was evaluated by TRNSYS 17 simulation code. Results show estimated savings using renewable energy sources. [Projekat Ministarstva nauke Republike Srbije, br. III42008

  10. An analysis of representative heating load lines for residential HSPF ratings

    Energy Technology Data Exchange (ETDEWEB)

    Rice, C. Keith [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Shen, Bo [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Shrestha, Som S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-07-01

    This report describes an analysis to investigate representative heating loads for single-family detached homes using current EnergyPlus simulations (DOE 2014a). Hourly delivered load results are used to determine binned load lines using US Department of Energy (DOE) residential prototype building models (DOE 2014b) developed by Pacific Northwest National Laboratory (PNNL). The selected residential single-family prototype buildings are based on the 2006 International Energy Conservation Code (IECC 2006) in the DOE climate regions. The resulting load lines are compared with the American National Standards Institute (ANSI)/Air-Conditioning, Heating, and Refrigeration Institute (AHRI) Standard 210/240 (AHRI 2008) minimum and maximum design heating requirement (DHR) load lines of the heating seasonal performance factor (HSPF) ratings procedure for each region. The results indicate that a heating load line closer to the maximum DHR load line, and with a lower zero load ambient temperature, is more representative of heating loads predicted for EnergyPlus prototype residential buildings than the minimum DHR load line presently used to determine HSPF ratings. An alternative heating load line equation was developed and compared to binned load lines obtained from the EnergyPlus simulation results. The effect on HSPF of the alternative heating load line was evaluated for single-speed and two-capacity heat pumps, and an average HSPF reduction of 16% was found. The alternative heating load line relationship is tied to the rated cooling capacity of the heat pump based on EnergyPlus autosizing, which is more representative of the house load characteristics than the rated heating capacity. The alternative heating load line equation was found to be independent of climate for the six DOE climate regions investigated, provided an adjustable zero load ambient temperature is used. For Region IV, the default DOE climate region used for HSPF ratings, the higher load line results in an ~28

  11. Recruitment of single human low-threshold motor units with increasing loads at different muscle lengths.

    Science.gov (United States)

    McNulty, P A; Cresswell, A G

    2004-06-01

    We investigated the recruitment behaviour of low threshold motor units in flexor digitorum superficialis by altering two biomechanical constraints: the load against which the muscle worked and the initial muscle length. The load was increased using isotonic (low load), loaded dynamic (intermediate load) and isometric (high load) contractions in two studies. The initial muscle position reflected resting muscle length in series A, and a longer length with digit III fully extended in series B. Intramuscular EMG was recorded from 48 single motor units in 10 experiments on five healthy subjects, 21 units in series A and 27 in series B, while subjects performed ramp up, hold and ramp down contractions. Increasing the load on the muscle decreased the force, displacement and firing rate of single motor units at recruitment at shorter muscle lengths (Precruitment pattern was observed between loaded dynamic and isotonic contractions, but not between isometric and loaded dynamic contractions. Thus, the recruitment properties of single motor units in human flexor digitorum superficialis are sensitive to changes in both imposed external loads and the initial length of the muscle.

  12. Reduced phrenic motoneuron recruitment during sustained inspiratory threshold loading compared to single-breath loading: a twitch interpolation study

    Directory of Open Access Journals (Sweden)

    Mathieu Raux

    2016-11-01

    Full Text Available In humans, inspiratory constraints engage cortical networks involving the supplementary motor area. Functional magnetic resonance imaging (fMRI shows that the spread and intensity of the corresponding respiratory-related cortical activation dramatically decrease when a discrete load becomes sustained. This has been interpreted as reflecting motor cortical reorganisation and automatisation, but could proceed from sensory and/or affective habituation. To corroborate the existence of motor reorganisation between single-breath and sustained inspiratory loading (namely changes in motor neurones recruitment, we conducted a diaphragm twitch interpolation study based on the hypothesis that motor reorganisation should result in changes in the twitch interpolation slope. Fourteen healthy subjects (age: 21 – 40 years were studied. Bilateral phrenic stimulation was delivered at rest, upon prepared and targeted voluntary inspiratory efforts (vol, upon unprepared inspiratory efforts against a single-breath inspiratory threshold load (single-breath, and upon sustained inspiratory efforts against the same type of load (continuous. The slope of the relationship between diaphragm twitch transdiaphragmatic pressure and the underlying transdiaphragmatic pressure was –1.1 ± 0.2 during vol, –1.5 ± 0.7 during single-breath, and -0.6 ± 0.4 during continuous (all slopes expressed in percent of baseline.percent of baseline-1 all comparisons significant at the 5% level. The contribution of the diaphragm to inspiration, as assessed by the gastric pressure to transdiaphragmatic pressure ratio, was 31 ± 17 % during vol, 22 ± 16 % during single-breath (p=0.13, and 19 ± 9 % during continuous (p = 0.0015 vs. vol. This study shows that the relationship between the amplitude of the transdiaphragmatic pressure produced by a diaphragm twitch and its counterpart produced by the underlying diaphragm contraction is not unequivocal. If twitch interpolation is interpreted as

  13. Development of piglets raised in a new multi-litter housing system vs. conventional single-litter housing until 9 weeks of age

    NARCIS (Netherlands)

    Nieuwamerongen, van S.E.; Soede, N.M.; Peet-Schwering, van der C.M.C.; Kemp, B.; Bolhuis, J.E.

    2015-01-01

    This study compared the development until 9 wk of age of piglets raised in either a multi-litter (ML) system or a conventional single-litter (SL) system. The ML system consisted of a multi-suckling system with 5 sows and their litters before weaning, followed by housing in a pen with enrichment in a

  14. Prevalence and covariates of food insecurity among residents of single-room occupancy housing in Chicago, IL, USA.

    Science.gov (United States)

    Bowen, Elizabeth A; Bowen, Sarah K; Barman-Adhikari, Anamika

    2016-04-01

    Emerging evidence suggests that food insecurity is a significant public health concern among people who are homeless or marginally housed. The present study assessed prevalence of food insecurity and its covariates among a group of marginally housed individuals living in single-room occupancy (SRO) dwellings, a population for which there is little extant health or nutrition research. Cross-sectional survey incorporating the Household Food Insecurity Access Scale. Ten private SRO residences in the Uptown neighbourhood of Chicago, IL, USA, 2013. SRO residents over 18 years of age who were able to communicate verbally in English (n 153). Food insecurity was widespread among SRO residents, with 75 % of the sample considered food insecure and 52 % meeting criteria for severe food insecurity. Bivariate analyses indicated that female gender, eating most meals at a soup kitchen, having a mental health condition, problem drinking, having at least one chronic health condition, and diabetes were all significantly associated with food insecurity. In the multivariate ordered logistic regression model, eating most meals at a soup kitchen remained as the only significant correlate of food insecurity (OR=10·13). SRO residents and other marginally housed populations face unique food access challenges. Although targeted assistance in the form of food stamps and congregate meal programmes remains critical, efforts to prevent and address food insecurity among homeless and marginally housed individuals should include policy interventions that recognize poverty as the root cause of food insecurity and aim to increase overall income and improve housing conditions.

  15. Telemetric assessment of social and single housing: Evaluation of electrocardiographic intervals in jacketed cynomolgus monkeys.

    Science.gov (United States)

    Kaiser, Robert A; Tichenor, Stephen D; Regalia, Douglas E; York, Kristina; Holzgrefe, Henry H

    2015-01-01

    Proactive efforts to socially house laboratory animals are a contemporary, important focus for enhancing animal welfare. Jacketing cynomolgus monkeys has been traditionally considered an exclusionary criterion for social housing based on unsubstantiated concerns that study conduct or telemetry equipment might be compromised. Our objective was to evaluate the effects of jacketing naïve, adolescent cynomolgus monkeys in different single and social housing types based on parallel comparisons of heart rate. Eight naive cynomolgus monkeys were randomized into pairs and ECG data were collected for 24h from each animal in each housing condition using a crossover design. Caging paradigms consisted of standard individual, standard pair, quaternary pair (4 linked cages), and European-style pair housing in non-sequential order varied by pair to control for possible time bias. Dosing and blood collection procedures were performed to characterize any effects of housing on ECG data during study conduct. There was no increase in the incidence of equipment damage in pair vs. individually housed animals. Further, animals in all 4 housing paradigms showed similar acclimation assessed as heart rate (mean 139-154 beats per minute), and maintained similar diurnal rhythms, with an expected slowing of the heart rate at night (aggregate lights out HR 110±4bpm compared to daytime 146±7bpm). This study demonstrates the effects of different social access and housing types on the study-naïve cynomolgus monkeys during jacketed cardiovascular telemetry data collection in a repeat-dose toxicology study design. There were no discernible effects of social housing on baseline ECG parameters collected via jacketed telemetry, and all animals maintained expected diurnal rhythms in all housing settings tested. These data demonstrate that cynomolgus monkeys can be socially housed during data collection as a standard practice, consistent with global efforts to improve study animal welfare. Copyright

  16. Enhancing load-following and/or spectral shift capability in single-sparger natural circulation boiling water reactors

    International Nuclear Information System (INIS)

    Oosterkamp, W.J.

    1992-01-01

    This patent describes a method for obtaining load-following capability in a coiling water reactor (BWR) wherein housed within a reactor pressure vessel (RPV) is a nuclear core disposed within a shroud having a shroud head and which with the RPV defines an annulus region disposed beneath the nuclear core, an upper steam dome connected to a steam outlet in the RPV, a core upper plenum formed within the shroud head and disposed atop the nuclear core, a chimney mounted atop the shroud head and in fluid communication with the core upper plenum and with a steam separator having a skirt which is in fluid communication with the steam dome, the region outside of the chimney defining a downcomer region, there being a water level established therein under normal operation of the BWR, and the RPV containing a feedwater inlet. It comprises: disposing a single sparger connected to the feedwater inlet above the steam separator skirt bottom about the interior circumference of the RPV at an elevation at approximately the water level established during normal operation of the BWR; and adjusting the feedwater flow through the inlet and into the sparger to vary the water level to be above, at or below the elevational location of the sparger in response to load-following need

  17. Energy-efficient houses built according to the energy performance requirements introduced in Denmark in 2006

    DEFF Research Database (Denmark)

    Tommerup, Henrik M.; Rose, Jørgen; Svendsen, Svend

    2007-01-01

    In order to meet new tighter building energy requirements introduced in Denmark in 2006 and prepare the way for future buildings with even lower energy consumption, single-family houses were built with the purpose to demonstrate that it is possible to build typical single-family houses with an en......% of the required and almost the level of typical passive houses.......In order to meet new tighter building energy requirements introduced in Denmark in 2006 and prepare the way for future buildings with even lower energy consumption, single-family houses were built with the purpose to demonstrate that it is possible to build typical single-family houses...... with an energy consumption that meets the demands without problems concerning building technology or economy. The paper gives a brief presentation of the houses and the applied energy-saving measures. The paper also presents results from measurements of the overall energy use, indoor climate and air tightness...

  18. Space heating with ultra-low-temperature district heating - A case study of four single-family houses from the 1980s

    DEFF Research Database (Denmark)

    Østergaard, Dorte Skaarup; Svendsen, Svend

    . These benefits can be maximized if district heating temperatures are lowered as much as possible. In this paper we report on a project where 18 Danish single-family houses from the 1980s were supplied by ultra-low-temperature district heating with a supply temperature as low as 45 °C for the main part...... the four houses were modelled in the building simulation tool IDA ICE. The simulation models included the actual radiator sizes and the models were used to simulate the expected thermal comfort in the houses and resulting district heating return temperatures. Secondly measurements of the actual district...... heating return temperatures in the houses were analysed for different times of the year. The study found that existing Danish single-family houses from the 1980s can be heated with supply temperatures as low as 45 °C for the main part of the year. Both simulation models and test measurements showed...

  19. BEARING CAPACITY OF A HORIZONTALLY LOADED SINGLE PILE SUPPORT WITH SLEEPERS

    Directory of Open Access Journals (Sweden)

    Buslov Anatoliy Semenovich

    2015-09-01

    Full Text Available The supports of a overhead wiring used in transport take up substantial loads both because of wires and constructions holding them and wind, dynamic and other extraordinary impacts. In case of using single-member piles a question about their stability appears. For this reason different sleepers constructions are used. In order to improve the bearing capacity of horizontally loaded single pile supports of the contact systems used in urban, road and rail transport, power lines, etc.., it is recommended to use sleepers as horizontally laid under the ground in the depth of support beams. The calculation methods for different support sleepers of different lengths and cross sections are not well investigated. The proposed calculation method allows determining the carrying capacity of horizontally loaded bearings with soil pieces of different structural dimensions and their location in the soil, which allows choosing the best option for cost and material consumption. The calculations offered by the authors prove the efficiency of sleepers use in order to increase the bearing capacity of horizontally loaded piles and the possibility to chose their size.

  20. Load Insensitive, Low Voltage Quadrature Oscillator Using Single Active Element

    Directory of Open Access Journals (Sweden)

    Jitendra Mohan

    2017-01-01

    Full Text Available In this paper, a load insensitive quadrature oscillator using single differential voltage dual-X second generation current conveyor operated at low voltage is proposed. The proposed circuit employs single active element, three grounded resistors and two grounded capacitors. The proposed oscillator offers two load insensitive quadrature current outputs and three quadrature voltage outputs simultaneously. Effects of non-idealities along with the effects of parasitic are further studied. The proposed circuit enjoys the feature of low active and passive sensitivities. Additionally, a resistorless realization of the proposed quadrature oscillator is also explored. Simulation results using PSPICE program on cadence tool using 90 nm Complementary Metal Oxide Semiconductor (CMOS process parameters confirm the validity and practical utility of the proposed circuit.

  1. Fatigue crack growth behaviour of carbon steel piping material subjected to single overload/under-load

    International Nuclear Information System (INIS)

    Arora, Punit; Tripathi, R.; Singh, P.K.; Bhasin, V.; Vijayan, P.K.

    2016-01-01

    The objective of the present study is to understand the Fatigue Crack Growth Rate (FCGR) behaviour after single over-load/ under-load event on carbon steel piping material. The tests have been carried out on standard Compact Tension (CT) specimens. The effect of different crack length to width ratio (a/W) of specimen and overload/under-load ratios on FCGR have been studied. The studies have shown significant reduction in FCG rate after overload event. The strain field has been measured using Digital Image Correlation (DIC) technique ahead of the crack tip to quantify the plastic zone size due to overload and constant amplitude load. In addition, plastic zone calculations have also been carried out using 3D finite element analyses for the prediction of post overload FCGR/ life. The predicted FCGR are in agreement with experimentally determined FCGR. (author)

  2. Surface acoustic load sensing using a face-shear PIN-PMN-PT single-crystal resonator.

    Science.gov (United States)

    Kim, Kyungrim; Zhang, Shujun; Jiang, Xiaoning

    2012-11-01

    Pb(In(0.5)Nb(0.5))O(3)-Pb(Mg(1/3)Nb(2/3))O(3)-PbTiO(3) (PIN-PMN-PT) resonators for surface acoustic load sensing are presented in this paper. Different acoustic loads are applied to thickness mode, thickness-shear mode, and face-shear mode resonators, and the electrical impedances at resonance and anti-resonance frequencies are recorded. More than one order of magnitude higher sensitivity (ratio of electrical impedance change to surface acoustic impedance change) at the resonance is achieved for the face-shear-mode resonator compared with other resonators with the same dimensions. The Krimholtz, Leedom, and Matthaei (KLM) model is used to verify the surface acoustic loading effect on the electrical impedance spectrum of face-shear PIN-PMN-PT single-crystal resonators. The demonstrated high sensitivity of face-shear mode resonators to surface loads is promising for a broad range of applications, including artificial skin, biological and chemical sensors, touch screens, and other touch-based sensors.

  3. Physics Simulation Software for Autonomous Propellant Loading and Gas House Autonomous System Monitoring

    Science.gov (United States)

    Regalado Reyes, Bjorn Constant

    2015-01-01

    1. Kennedy Space Center (KSC) is developing a mobile launching system with autonomous propellant loading capabilities for liquid-fueled rockets. An autonomous system will be responsible for monitoring and controlling the storage, loading and transferring of cryogenic propellants. The Physics Simulation Software will reproduce the sensor data seen during the delivery of cryogenic fluids including valve positions, pressures, temperatures and flow rates. The simulator will provide insight into the functionality of the propellant systems and demonstrate the effects of potential faults. This will provide verification of the communications protocols and the autonomous system control. 2. The High Pressure Gas Facility (HPGF) stores and distributes hydrogen, nitrogen, helium and high pressure air. The hydrogen and nitrogen are stored in cryogenic liquid state. The cryogenic fluids pose several hazards to operators and the storage and transfer equipment. Constant monitoring of pressures, temperatures and flow rates are required in order to maintain the safety of personnel and equipment during the handling and storage of these commodities. The Gas House Autonomous System Monitoring software will be responsible for constantly observing and recording sensor data, identifying and predicting faults and relaying hazard and operational information to the operators.

  4. Central Control of Heat Pump for Smart Grid Purposes Tested on Single Family Houses

    DEFF Research Database (Denmark)

    Pedersen, Tom S.; Andersen, Palle; Nielsen, Kirsten M.

    2013-01-01

    A challenge in Denmark in the near future is to balance the electrical grid due to a large increase in the renewable energy production mainly from wind turbines. In this work a central control system using heat pumps in single family houses to help balancing the grid is investigated. The central...

  5. United States housing, 2012

    Science.gov (United States)

    Delton Alderman

    2013-01-01

    Provides current and historical information on housing market in the United States. Information includes trends for housing permits and starts, housing completions for single and multifamily units, and sales and construction. This report will be updated annually.

  6. Sustainable Plus-energy Houses

    DEFF Research Database (Denmark)

    Kazanci, Ongun Berk; Olesen, Bjarne W.

    This study is an outcome of Elforsk, project number 344-060, Bæredygtige Energi-Plus huse (Sustainable plus-energy houses). The focus of this report is to document the approach and the results of different analyses concerning a plus-energy, single family house. The house was designed...... for an international student competition, Solar Decathlon Europe 2012 and after the competition it was used as a full-scale experimental facility for one year. During this period, different heating and cooling strategies were tested and the performance of the house regarding the thermal indoor environment and energy...... was monitored. This report is structured as follows. Chapter 1 presents the project and briefly explains the different phases of the project. The details of the house’s construction and its HVAC system are explained in Chapter 2, along with the energy efficiency measures and innovations. Chapter 3 introduces...

  7. Face and object encoding under perceptual load: ERP evidence.

    Science.gov (United States)

    Neumann, Markus F; Mohamed, Tarik N; Schweinberger, Stefan R

    2011-02-14

    According to the perceptual load theory, processing of a task-irrelevant distractor is abolished when attentional resources are fully consumed by task-relevant material. As an exception, however, famous faces have been shown to elicit repetition modulations in event-related potentials - an N250r - despite high load at initial presentation, suggesting preserved face-encoding. Here, we recorded N250r repetition modulations by unfamiliar faces, hands, and houses, and tested face specificity of preserved encoding under high load. In an immediate (S1-S2) repetition priming paradigm, participants performed a letter identification task on S1 by indicating whether an "X" vs. "N" was among 6 different (high load condition) or 6 identical (low load condition) letters. Letter strings were superimposed on distractor faces, hands, or houses. Subsequent S2 probes were either identical repetitions of S1 distractors, non-repeated exemplars from the same category, or infrequent butterflies, to which participants responded. Independent of attentional load at S1, an occipito-temporal N250r was found for unfamiliar faces. In contrast, no repetition-related neural modulation emerged for houses or hands. This strongly suggests that a putative face-selective attention module supports encoding under high load, and that similar mechanisms are unavailable for other natural or artificial objects. Copyright © 2010 Elsevier Inc. All rights reserved.

  8. Immediate non-occlusal loading of single implants in the aesthetic zone : A randomized clinical trial

    NARCIS (Netherlands)

    den Hartog, Laurens; Raghoebar, Gerry M.; Stellingsma, Kees; Vissink, Arjan; Meijer, Henny J. A.

    P>Aim This study compared the outcome of immediate non-occlusal loading with conventional loading for single implants in the maxillary aesthetic zone. It was hypothesized that immediate non-occlusal loading is not inferior to conventional loading. Materials and Methods Sixty-two patients with a

  9. Analysis of an adhesively bonded single lap joint subjected to eccentric loading

    DEFF Research Database (Denmark)

    Anyfantis, Konstantinos; Tsouvalis, N. G.

    2013-01-01

    is benchmarking of computational tools. The test is based on a Single Lap Joint subjected to Eccentric Loading (SLJ-EL). The basic concept that lies behind this configuration is that the applied in-plane tensile load leads the adhesive layer to develop normal stresses, in-plane and out-of-plane shear stresses...

  10. The development of a code of practice for single house on-site wastewater treatment in Ireland.

    Science.gov (United States)

    Gill, L W

    2011-01-01

    The performance of six separate percolation areas was intensively monitored to ascertain the attenuation effects of unsaturated subsoils with respect to on-site wastewater effluent: three sites receiving septic tank effluent, the other three sites receiving secondary treated effluent. The development of a biomat across the percolation areas receiving secondary treated effluent was restricted on these sites compared to those sites receiving septic tank effluent. This created significant differences in terms of the hydraulic loading on the percolation areas with implications for the transport and attenuation of indicator microorganisms and nitrogen down through the subsoils and into the groundwater. The results of this work have formed a large input into the production of a new Code of Practice Wastewater Treatment and Disposal Systems Serving Single Houses. This has led to changes in the design of on-site hydraulic loading from 180 L per capita per day (L/c.d) down to 150 L/c.d. The range of acceptable subsoils receiving septic tank effluent has narrowed for more highly permeable subsoils following a series of tracer studies using bacteriophages. However, the range has been extended for lower permeability subsoils (range 0.08 down to 0.06 m/d) receiving secondary treated effluent in order to encourage the effluent to spread further along the trenches. The maximum individual length of percolation trenches receiving secondary effluent has also been reduced to 10 m to encourage dispersion on a wider area. This paper thus highlights how research can directly feed into a Code of Practice.

  11. Radon in houses

    International Nuclear Information System (INIS)

    Toohey, R.E.; Essling, M.A.; Markun, F.

    1985-01-01

    The purpose of this study is to determine the concentrations of 222 Rn and its short-lived daughter products in the air of single-family houses in the midwestern US. During the past year, more than 200 houses were added to the study, resulting in a total of more than 400 houses. So far, results are available for 270 of these houses, equally divided between the Chicago area and Bloomsburg, Pennsylvania. 6 refs

  12. Remotely operated top loading filter housing

    International Nuclear Information System (INIS)

    Ross, M.J.; Carter, J.A.

    1989-01-01

    A high-efficiency particulate air (HEPA) filter system was developed for the Fuel Processing Facility at the Idaho Chemical Processing Plant. The system utilizes commercially available HEPA filters and allows in-cell filters to be maintained using operator-controlled remote handling equipment. The remote handling tasks include transport of filters before and after replacement, removal and replacement of the filter from the housing, and filter containment

  13. 49 CFR 179.500-10 - Protective housing.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Protective housing. 179.500-10 Section 179.500-10...-10 Protective housing. (a) Safety devices, and loading and unloading valves on tanks shall be protected from accidental damage by approved metal housing, arranged so it may be readily opened to permit...

  14. Sustainable renovation concepts for single-family houses

    DEFF Research Database (Denmark)

    Vanhoutteghem, Lies; Tommerup, Henrik M.; Svendsen, Svend

    , the financial possibilities of the homeowner etc. Calculation of packages of energy efficient renovation solutions targeted the three segments of houses show that primary energy use and heating bill can be reduced with up to about 75% or a factor 4 corresponding to the level of a new house or better. It seems...... that the passive house level can not quite be reached with standard solutions. They require that more ambitious measures are applied. The total investment needed to reduce the heating bill by a factor 4 including replacement of e.g. roof and windows is up to EUR 100,000. It is generally difficult to obtain...... be seen as a possibility to make it easy for the homeowner to comply with possible future requirements to realize far-reaching energy savings in connection with extensive renovations, provided that the building sector offers the solutions. Homeowners need someone to take care of all relevant steps...

  15. Is there an upward long term trend in Danish real house prices?

    DEFF Research Database (Denmark)

    Skak, Morten

    2012-01-01

    In Denmark, like in other countries, there is no agreement on the fundamental long term path of real house prices and the sustainability of the present price level. The paper presents Danish house price indices and discusses the question of quality correction of the indices. Subsequently, factors...... behind the long term trend in real house prices and its sustainability are discussed. The paper finds an annual real growth trend around 1.5 per cent for Danish single family house prices likely for the coming ten years....

  16. Initiatives for the energy renovation of single-family houses inDenmark evaluated on the basis of barriers and motivators

    DEFF Research Database (Denmark)

    Grøn Bjørneboe, Matilde; Svendsen, Svend; Heller, Alfred

    2018-01-01

    The renovation of single-family houses in Denmark is progressing only slowly. Changes in current pol-icy are needed if the political goal of a fossil-free building sector as part of a fossil-free society is to beachieved. Known barriers and motivators for energy renovation are identified, and arr......The renovation of single-family houses in Denmark is progressing only slowly. Changes in current pol-icy are needed if the political goal of a fossil-free building sector as part of a fossil-free society is to beachieved. Known barriers and motivators for energy renovation are identified......, suggestions are madefor improvement in four areas: (1) focus on non-energy benefits rather than investment, (2) enhance-ment of subsidy system, (3) including relevant renovation plans in the energy performance certificate(EPC), and (4) long-term regulation on the maximum allowed energy consumption of houses....

  17. The effect of building regulations on energy consumption in single family houses in Denmark

    DEFF Research Database (Denmark)

    Kjærbye, Vibeke; Larsen, Anders; Togeby, Mikael

    This paper explores how changes in regulatory requirements for energy efficiency in buildings (in the US also known as building energy codes) affect household energy consumption. The focus in this paper is on natural gas consumption by Danish single-family owner-occupied houses. Unlike most other...... advanced econometric methods we examine differences in heating energy consumption due to different building regulation requirements at the time of house construction. As for the effect of the building regulation, we find that changes in Danish building regulations have led to significant reductions...... in energy used for heating. The latest revision of the Danish building regulation covered by this paper is that of 1998. This revision has resulted in a 7% reduction in natural gas consumption....

  18. Perceptual load manipulation reveals sensitivity of the face-selective N170 to attention.

    Science.gov (United States)

    Mohamed, Tarik N; Neumann, Markus F; Schweinberger, Stefan R

    2009-05-27

    It has been controversial whether the face-sensitive N170 is affected by selective attention. We manipulated attention sensu Lavie's perceptual load theory to short (200 ms) presentations of task-irrelevant unfamiliar faces or houses, while participants identified superimposed target letters 'X' versus 'N'. These targets were strings of either six identical (low load) or six different letters (high load). Under low load, we found a prominent face-selective N170 response. Under high load, however, we not only observed a dramatic reduction of the face N170 but also an unexpected enhancement of the house N170, such that face selectivity was almost completely lost. We conclude that the early stages of face processing indexed by the N170 strongly depend on selective attention.

  19. Immediate loading with single-piece implant following extraction

    Directory of Open Access Journals (Sweden)

    Hemlata Dwivedi

    2017-01-01

    Full Text Available Although dental implantology had evolved over a number of years, many dental surgeons are unaware of the concept of immediate loading with the use of one-piece implant that began in the early 1960s. The goal of successful prosthodontics rehabilitation is to provide function, esthetics, and comfort to the patient. The aim of this literature is to provide an overview of one-piece implant, with its advantages and disadvantages over conventional two-piece implant. Immediate prosthetic of a one-piece system allows for a better tissue healing and better adhesion of gingival mucosa to form a collar which is healthy and adherent to the implant, avoiding a second surgical procedure, and also includes a very important aspect esthetics. This article describes a case report of immediate loading with single-piece implant following extraction.

  20. Loading direction-dependent shear behavior at different temperatures of single-layer chiral graphene sheets

    Science.gov (United States)

    Zhao, Yang; Dong, Shuhong; Yu, Peishi; Zhao, Junhua

    2018-06-01

    The loading direction-dependent shear behavior of single-layer chiral graphene sheets at different temperatures is studied by molecular dynamics (MD) simulations. Our results show that the shear properties (such as shear stress-strain curves, buckling strains, and failure strains) of chiral graphene sheets strongly depend on the loading direction due to the structural asymmetry. The maximum values of both the critical buckling shear strain and the failure strain under positive shear deformation can be around 1.4 times higher than those under negative shear deformation. For a given chiral graphene sheet, both its failure strain and failure stress decrease with increasing temperature. In particular, the amplitude to wavelength ratio of wrinkles for different chiral graphene sheets under shear deformation using present MD simulations agrees well with that from the existing theory. These findings provide physical insights into the origins of the loading direction-dependent shear behavior of chiral graphene sheets and their potential applications in nanodevices.

  1. Prefabricated EPS Elements used as Strip Foundation of a Single-family House with a Double Brick Wall

    OpenAIRE

    Rasmussen, Torben Valdbjørn

    2008-01-01

    A new prefabricated lightweight element was designed for a strip foundation that was demonstrated on site as the base of a single-family house with a double brick wall. The element was placed on a stable surface underneath the top soil layer, just 0.25 m underneath the finished ground surface. The prefabricated element was designed to fulfil the requirements of low energy consumption required by the new Danish Building Regulations. The base of the house was cast in one working operation and c...

  2. Research of thermal dynamic characteristics for variable load single screw refrigeration compressor with different capacity control mechanism

    International Nuclear Information System (INIS)

    Wang, Zengli; Wang, Zhenbo; Wang, Jun; Jiang, Wenchun; Feng, Quanke

    2017-01-01

    Highlights: • Theoretical models of SSRC under part-load condition have been established. • The experiment of SSRC performance under part-load condition was conducted. • Thermal dynamic characteristic of SSRC under part-load condition was gained. • Economy and reliability of SSRC under part-load condition was analyzed. - Abstract: In the single screw refrigeration compressor (SSRC), the capacity control mechanism is normally employed to meet the actual required cooling capacity under different load conditions. In this paper, theoretical calculation models describing the working process of the SSRC with the single slide valve capacity control mechanism (SVCCM) and SSRC with the frequency conversion regulating mechanism (FCRM) are established to research the thermal dynamic characteristics for variable load SSRC under part-load conditions. Experimental investigation on a SSRC under part-load conditions is also carried out to verify the theoretical calculation models. By using these validated models, the thermodynamic performances and dynamic characteristics of the SSRC with different capacity control mechanism under part-load conditions have been analyzed and compared. Through the comparison, the economical efficiency and reliability of the SSRC with different capacity control mechanism were obtained. All of these works can provide the basis for the later optimization design for the variable load single screw refrigeration compressor.

  3. The First "Comfort Houses" in Denmark

    DEFF Research Database (Denmark)

    Brunsgaard, Camilla; Knudstrup, Mary-Ann; Heiselberg, Per

    2009-01-01

    The "Comfort Houses" is the most ambitious building project in passive houses in Denmark until today. Eight single family houses are built and designed by seven different consortiums. Besides fulfilling the German passive house standard the goal was to build the houses according to Danish tradition...

  4. House owners’ experience and satisfaction with Danish low-energy houses

    DEFF Research Database (Denmark)

    Knudsen, Henrik Nellemose; Kragh, Jesper

    2015-01-01

    The purpose of this study was to identify experience and satisfaction with new Danish detached low-energy single-family houses. A questionnaire survey was carried out in the autumn of 2013 among owners of newly built energy class 2015 houses. It included i.a. questions on their overall satisfacti...

  5. Load handling gripper

    International Nuclear Information System (INIS)

    Holloway, C.

    1982-01-01

    An apparatus for releasably engaging and moving workpieces comprises pivotable gripper jaws with a spring-loaded plunger to maintain the jaws in a closed condition. The plunger is slidable in a bore in a housing and the end of the plunger remote from the jaws cooperates with a blind end of the bore to provide a gas cushion. A rod in conjunction with a backplate (not shown) are provided to cause the jaws to open and release a workpiece on axial movement of the housing in a first direction through a predetermined distance and releasable locking means maintain the jaws in an open condition. On axial movement of the housing in the reverse direction the locking means are released to allow the spring-loaded plunger to return to a position to close to jaws. (author)

  6. United States housing, first quarter 2013

    Science.gov (United States)

    Delton Alderman

    2014-01-01

    Provides current and historical information on housing market in the United States. Information includes trends for housing permits and starts, housing under construction, and housing completions for single and multifamily units, and sales and construction. This report will be updated regularly.

  7. Moisture supply in Danish single-family houses – the influence of occupant behaviour and type of room

    DEFF Research Database (Denmark)

    Møller, Eva B.; Hansen, Ernst Jan de Place

    2017-01-01

    According to ISO 13788, the internal moisture supply in dwellings can be described by humidity classes defined by outdoor temperature, occupancy and ventilation. Hygrothermal measurements in indoor air in 500 Danish single-family houses were made to investigate if this corresponds with reality....... The study focuses on the dependency of number and age of occupants, occupants’ time spent in the house, square meters living space, ventilation habits and type of room. Moisture supply depends on the type of room; bathroom, basement and living room have the highest values. None of the other parameters seems...

  8. Active load management in an intelligent building using model predictive control strategy

    DEFF Research Database (Denmark)

    Zong, Yi; Kullmann, Daniel; Thavlov, Anders

    2011-01-01

    This paper introduces PowerFlexHouse, a research facility for exploring the technical potential of active load management in a distributed power system (SYSLAB) with a high penetration of renewable energy and presents in detail on how to implement a thermal model predictive controller for load...... shifting in PowerFlexHouse heaters' power consumption scheme. With this demand side control study, it is expected that this method of demand response can dramatically raise energy efficiencies and improve grid reliability, when there is a high penetration of intermittent energy resources in the power...

  9. Measurement of 65Zn in 5-yen coin present in the houses nearby JCO

    International Nuclear Information System (INIS)

    Kono, Masuchika; Koizumi, Yoshinobu

    2000-01-01

    In 1999, a critical accident occurred in Calder-Hall type power reactor of JCO for the first in Japan. This study aimed to estimate γ exposure dose utilizing a five-yen coin present in the houses nearby JCO at the time of accident. The coin, which is composed of Cu-Zn alloy is present every houses and its quality is well controlled by Ministry of Finance. In addition, Zn isotope ( 65 Zn) produced by neutron exposure has a long half-life (244.1 days) and emits γ ray with high energy of 1115.5 keV, which allows measurement at a low level radiation. So, five-yen coin was used as the subject. The exposure dose of inhabitant was estimated based on the activity on 5-yen coins collected from the houses at 13 points at different distances from JCO, which was determined by a low-level measurement system equipped with a pure-Ge semiconductor. The relationship between dose equivalent (mSv) and the distance from JCO was presented. At the time of JCO accident, the evacuation order was given to the inhabitants living within 300 m from the company. However, the present study indicated that the exposure dose was as high as 220 mSv at the site 100 m apart from JCO. Therefore, it is concluded that the inhabitants living in the area more than 350 m from JCO should also have taken refuge. (M.N.)

  10. Horizontal temperature distribution in a plus-energy house: cooling season measurements

    DEFF Research Database (Denmark)

    Kazanci, Ongun Berk; Olesen, Bjarne W.

    2015-01-01

    The present study is concerned with the air and operative temperatures at different locations in a detached, one-story, single family, plus-energy house. The house was located in Denmark and it has been used as a full-scale experimental facility with heated dummies to simulate occupants living...

  11. Comparison of Buildings\\' Thermal Loads against Building Orientations for Sustainable Housing in Pakistan

    Directory of Open Access Journals (Sweden)

    Arif Khan

    2012-07-01

    Full Text Available As the sustainable settlements have been included as a vital end product of all planning exercises, the architectural layouts should be well integrated with the sun path charts and the orientations of windows. Appropriate orientations can offer thermally indoor conditions besides physical and psychological comfort in any settlement at lesser energy demand. This investigation uses a vast number of computer simulations to visualize and make better decisions about heating and cooling requirements of a building and facades as a function of window orientation in composite climatic condition of Lahore. This study in particular evaluates the solar load in residential buildings responsive to the objective of sustainable new housing leading to thoughtful integration of architecture. The orientation of the buildings could then be essentially integrated to the current architectural and urban design practices in order to optimize the relationship between the given site ant the orientations for sustainable developments.

  12. Single bunch beam loading on the SLAC three-kilometer accelerator

    International Nuclear Information System (INIS)

    Koontz, R.F.; Loew, G.A.; Miller, R.H.; Wilson, P.B.

    1977-03-01

    Since the report on single bunch beam loading experiments at SLAC at the 1975 Particle Accelerator Conference, it has been possible to obtain a much better understanding and agreement of theoretical and experimental results related to this problem. These improvements were made possible by two developments: the generation of a ''wake-field'' function for the SLAC 3-km slow-wave structure and the use of this function to calculate single bunch energy spectra. The wake-field function which gives the time decay of the fields generated by the passage of a delta-function beam was derived by summing all the TM cylindrically symmetrical modes of an equivalent accelerator cavity. By multiplying this wake-field function by a measured bunch density function and integrating along the bunch, it is possible to calculate the energy of each electron in the bunch. This in turn enables one to predict the energy spectrum for any given phase angle of the bunch with respect to the crest of the rf accelerating wave. Agreement between these calculations and experimental measurements is very good. These results are presented, and the possible sources of some of the remaining discrepancies are discussed

  13. Single bunch beam loading on the SLAC three-kilometer accelerator

    International Nuclear Information System (INIS)

    Koontz, R.F.; Loew, G.A.; Miller, R.H.; Wilson, P.B.

    1977-01-01

    Since the report on single bunch beam loading experiments at SLAC at the 1975 Particle Accelerator Conference, it has been possible to obtain a much better understanding and agreement of theoretical and experimental results related to this problem. These improvements have been made possible by two developments: the generation of a ''wake-field'' function for the SLAC 3-km slow-wave structure and the use of this function to calculate single bunch energy spectra. The wake-field function which gives the time decay of the fields generated by the passage of a delta-function beam was derived by summing all the TM cylindrically symmetrical modes of an equivalent accelerator cavity. By multiplying this wake-field function by a measured bunch density function and integrating along the bunch, it is possible to calculate the energy of each electron in the bunch. This in turn enables one to predict the energy spectrum for any given phase angle of the bunch with respect to the crest of the rf accelerating wave. Agreement between these calculations and experimental measurements is very good. These results are presented and the possible sources of some of the remaining discrepancies are discussed

  14. Strain measurements in a rotary engine housing

    Science.gov (United States)

    Lee, C. M.; Bond, T. H.; Addy, H. E.; Chun, K. S.; Lu, C. Y.

    1989-01-01

    The development of structural design tools for Rotary Combustion Engines (RCE) using Finite Element Modeling (FEM) requires knowledge about the response of engine materials to various service conditions. This paper describes experimental work that studied housing deformation as a result of thermal, pressure and mechanical loads. The measurement of thermal loads, clamping pressure, and deformation was accomplished by use of high-temperature strain gauges, thermocouples, and a high speed data acquisition system. FEM models for heat transfer stress analysis of the rotor housing will be verified and refined based on these experimental results.

  15. The building process of single-family houses and the embeddedness (or disembeddedness) of energy

    International Nuclear Information System (INIS)

    Palm, Jenny

    2013-01-01

    People building their own houses have, at least theoretically, substantial autonomy when choosing, for example, a heating system and windows. In this article, focus is on the process of building new single-family houses and how energy efficiency and energy-efficient technology are incorporated into the building process. The conclusions emphasize energy as only one factor in housing purchase decisions. It is a big challenge to make low-energy building important to consumers. Consumer preferences for new products are unlikely to fully develop unless individuals have the opportunity to interact with them. It is difficult for consumers to know what to ask for if they lack experience of energy-efficient technologies. In the studied cases, the building codes and established standards became extremely decisive for how energy issues were included in the process. There is a need to change the design of incentives so as to make the least energy-efficient choice the most expensive. The most energy-efficient solution should be standard, and if the buyer wants to depart from that standard and build using less energy-efficient construction, then that should cost more. -- Highlights: •Actors do not see energy efficiency as a critical problem. •Factors other than costs and price were important in the decision making. •Energy issues just one factor in housing purchase decisions. •The consumers don′t know what to ask for. •Building norms should require the most energy efficient solution

  16. Prefabricated EPS Elements used as Strip Foundation of a Single-family House with a Double Brick Wall

    DEFF Research Database (Denmark)

    Rasmussen, Torben Valdbjørn

    2008-01-01

    A new prefabricated lightweight element was designed for a strip foundation that was demonstrated on site as the base of a single-family house with a double brick wall. The element was placed on a stable surface underneath the top soil layer, just 0.25 m underneath the finished ground surface....... The prefabricated element was designed to fulfil the requirements of low energy consumption required by the new Danish Building Regulations. The base of the house was cast in one working operation and completed within two working days. The element, made of expanded polystyrene, was designed to be handled on site...

  17. The effect of building regulations on energy consumption in single-family houses in Denmark. Final version

    Energy Technology Data Exchange (ETDEWEB)

    Hansen Kjaerbye, V. (Roskilde Univ.. Dept. of Environmental, Social and Spatial Change, Roskilde (Denmark)); AKF (Danish Institute of Governmental Research, Copenhagen (Denmark)); Larsen, Anders E. (Roskilde Univ.. Dept. of Society and Globalisation, Roskilde (Denmark)); Togeby, M (Ea Energy Analyses, Copenhagen (Denmark))

    2010-04-15

    This paper explores how changes in regulatory requirements for energy efficiency in buildings (in the US also known as building energy codes) affect household energy consumption. The focus in this paper is on natural gas consumption by Danish single-family owner-occupied houses. Unlike most other papers investigating household energy consumption this paper uses a unique panel data set constructed by merging several administrative data bases. The data set describes house and household characteristics, outdoor temperature and actual metered natural gas consumption over 6 years (1998-2003). Applying advanced econometric methods we examine differences in heating energy consumption due to different building regulation requirements at the time of house construction. As for the effect of the building regulation, we find that changes in Danish building regulations have led to significant reductions in energy used for heating. The latest revision of the Danish building regulation covered by this paper is that of 1998. This revision has resulted in a 7 percent reduction in natural gas consumption. (Author)

  18. Refractive indices of CaF2 single crystals under elastic shock loading

    Science.gov (United States)

    Li, Y.; Zhou, X. M.; Liu, C. L.; Luo, S. N.

    2017-07-01

    Refractive indices and Hugoniots of CaF2 single crystals are investigated by laser displacement interferometry under shock loading below 5 GPa. Birefringence is observed for the [110] loading. We obtain the Hugoniot equation of states for [100], [110] and [111], and refractive indices for these orientations with consideration of their polarization. The measured refractive indices are in reasonable agreement with predictions based on the piezo-optic theory, and are used to refine the elasto-optic coefficients.

  19. Effect of loading orientations on the microstructure and property of Al−Cu single crystal during stress aging

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Jiqiang [School of Material Science and Engineering, Central South University, Changsha 410083 (China); Chen, Zhiguo, E-mail: zgchen@mail.csu.edu.cn [School of Material Science and Engineering, Central South University, Changsha 410083 (China); Hunan University of Humanities, Science and Technology, Loudi 417000 (China); Deng, Yunlai [School of Material Science and Engineering, Central South University, Changsha 410083 (China); State Key Laboratory of High Performance and Complex Manufacturing, Central South University, Changsha 410083 (China); Guo, Xiaobin; Ren, Jieke [School of Material Science and Engineering, Central South University, Changsha 410083 (China)

    2016-07-15

    The precipitation behavior and property of Al−Cu alloy during stress aging under various loading orientations were investigated using single crystals. The resulting microstructures and the strength property were examined by transmission electron microscope (TEM) and compression test, respectively, and the effect of the distribution of θ′-plates on strength property were discussed. The results show that the precipitation distribution of θ′ was significantly affected by the loading orientation during stress aging of Al−Cu single crystals. Loading along close to 〈011〉{sub Al} directions provided more uniform precipitation distribution of θ′ as compared to loading along close to 〈001〉{sub Al} directions, and therefore provided higher strengthening stress of the θ′-plates for the stress aging sample. The results suggested that regulating the distribution of θ′ and therefore improving strength property are possible via controlling the loading orientation during stress aging. - Highlights: • We studied the effect of loading directions on stress aging of Al−Cu single crystal. • Precipitation distribution of θ′ was noticeably affected by the loading direction. • Loading along close to 〈011〉{sub Al} directions reduced the stress-orienting effect. • The strength property is closely related to the precipitation distribution of θ′. • It is possible to regulate the distribution of θ′ and improve strength property.

  20. Space heating with ultra-low-temperature district heating - a case study of four single-family houses from the 1980s

    DEFF Research Database (Denmark)

    Østergaard, Dorte Skaarup; Svendsen, Svend

    2017-01-01

    . These benefits can be maximized if district heating temperatures are lowered as much as possible. In this paper we report on a project where 18 Danish single-family houses from the 1980s were supplied by ultra-low temperature district heating with a supply temperature as low as 45 degrees C for the main part...... of the year. The houses were heated by the existing hydraulic radiator systems, while domestic hot water was prepared by use of district heating and electric boosting. This paper evaluated the heating system temperatures that were necessary in order to maintain thermal comfort in four of the houses. First...... the four houses were modelled in the building simulation tool IDA ICE. The simulation models included the actual radiator sizes and the models were used to simulate the expected thermal comfort in the houses and resulting district heating return temperatures. Secondly measurements of the actual district...

  1. Allostatic Load: Single Parents, Stress-Related Health Issues, and Social Care

    Science.gov (United States)

    Johner, Randy L.

    2007-01-01

    This article explores the possible relationships between allostatic load (AL) and stress-related health issues in the low-income single-parent population, using both a population health perspective (PHP) and a biological framework. A PHP identifies associations among such factors as gender, income, employment, and social support and their…

  2. Optimal Integration of Cascade Thermoelectric Cooler into Electronic Housing: Experimental Approach

    Science.gov (United States)

    Semeniuk, V.; Protsenko, D.

    2018-06-01

    The problem of the optimal integration of thermoelectrically cooled optoelectronic components into an electronic housing is studied with the emphasis on practical implementation. The lines of 2-stage and 3-stage thermoelectric coolers (TECs) compatible with TO8 housing have been developed, and their parameters are measured in a wide range of heat sink temperatures. The TECs are optimized to receive a temperature difference of 100-110 K under a heat load from 70 mW to 100 mW with minimal power consumption. To fit into a standard housing interior, all the TECs have the same overall dimensions, regardless of the number of stages. Details of the TEC configurations and their performance characteristics are presented and discussed.

  3. Smart house-based optimal operation of thermal unit commitment for a smart grid considering transmission constraints

    Science.gov (United States)

    Howlader, Harun Or Rashid; Matayoshi, Hidehito; Noorzad, Ahmad Samim; Muarapaz, Cirio Celestino; Senjyu, Tomonobu

    2018-05-01

    This paper presents a smart house-based power system for thermal unit commitment programme. The proposed power system consists of smart houses, renewable energy plants and conventional thermal units. The transmission constraints are considered for the proposed system. The generated power of the large capacity renewable energy plant leads to the violated transmission constraints in the thermal unit commitment programme, therefore, the transmission constraint should be considered. This paper focuses on the optimal operation of the thermal units incorporated with controllable loads such as Electrical Vehicle and Heat Pump water heater of the smart houses. The proposed method is compared with the power flow in thermal units operation without controllable loads and the optimal operation without the transmission constraints. Simulation results show the validation of the proposed method.

  4. THE IMPORTANCE OF HOUSING CONSTRUCTION EXPERIENCE IN THE USSR AS MEANS OF FORMING HUMANITARIAN SPACE FOR PRESENT-DAY RUSSIA

    Directory of Open Access Journals (Sweden)

    Golomazova Tamara Nikolaevna

    2015-06-01

    Full Text Available Today the current task of the social policy of Russia is solution of the housing problem. In Russia today there is a lack of housing, especially modern housing of good quality. In the article the experience of mass housing construction in the USSR is considered. The reasons of housing crisis in the USSR and the ways of its overcome, which were offered in the 60—80th of the 20th century are analyzed. The author pays special attention to the positive component of the experience of overcoming the housing crisis, but also its disadvantages are underlined. The author believes, that in future specialists we should form not only a knowledge of housing construction experience in the USSR, but the understanding of the importance of this experience and opportunity to use it in the contemporary Russian conditions. The author points out, what exactly can be used to solve the housing problem of present-day Russia basing on this experience.

  5. Situation-Based Housing

    DEFF Research Database (Denmark)

    Duelund Mortensen, Peder

    2011-01-01

    Presentation of urban housing research on flexible housing types in the Copenhagen Region: Theoretical background, methodology, analyse of spatial organization, interviews and results. Cases: Pærehaven in Ølby, Køge and M-house in Ørestad, Copenhagen......Presentation of urban housing research on flexible housing types in the Copenhagen Region: Theoretical background, methodology, analyse of spatial organization, interviews and results. Cases: Pærehaven in Ølby, Køge and M-house in Ørestad, Copenhagen...

  6. Conformal house

    DEFF Research Database (Denmark)

    Ryttov, Thomas Aaby; Sannino, Francesco

    2010-01-01

    fixed point. As a consistency check we recover the previously investigated bounds of the conformal windows when restricting to a single matter representation. The earlier conformal windows can be imagined to be part now of the new conformal house. We predict the nonperturbative anomalous dimensions...... at the infrared fixed points. We further investigate the effects of adding mass terms to the condensates on the conformal house chiral dynamics and construct the simplest instanton induced effective Lagrangian terms...

  7. Numerical simulation of a cooling tower coupled with heat pump system associated with single house using TRNSYS

    International Nuclear Information System (INIS)

    Chargui, R.; Sammouda, H.; Farhat, A.

    2013-01-01

    Highlights: • We simulate a cooling tower coupled with heat pump system and a single zone using TRNSYS. • We examine the temperature of water inside the cooling tower and inside the single zone. • We study the temporal evolution of the all parameters for 4500 h operation in winter in Tunisia. - Abstract: The industrial cooling towers in Tunisia meet difficulties due to the poor coordination between the utility and process sectors. In this study, we will consider especially the vapor recovery of the wastewater from the industrial activity in south Tunisia. By using the heat pump for high capacity, the problem for vapor from wastewater may be resolved. The coupling for the cooling tower and the heat pump system is investigated by TRNSYS software. The system of cooling tower is also associated with a single zone which is related to heat exchangers. An optimization model for the operation of a cooling water system was developed that accounts for a cooling tower, and a network of pipelines and heat exchangers for heating a single house. This work is based on numerical studies; the cooling tower performance, the single house, the heat pump and the heat exchanger that are simulated using TRNSYS model. The circulation of cooling water system is assured by a counter flow. The evaluations of the cooling tower geometry and performances are based on an adaptive version of Merkel’s method witch integrated in TRNSYS. The results of optimization using TRNSYS are validated by several theoretical and experimental studies

  8. CFD Prediction on the Pressure Distribution and Streamlines around an Isolated Single-Storey House Considering the Effect of Topographic Characteristics

    Science.gov (United States)

    Abdullah, J.; Zaini, S. S.; Aziz, M. S. A.; Majid, T. A.; Deraman, S. N. C.; Yahya, W. N. W.

    2018-04-01

    Single-storey houses are classified as low rise building and vulnerable to damages under windstorm event. This study was carried out with the aim to investigate the pressure distribution and streamlines around an isolated house by considering the effect of terrain characteristics. The topographic features such as flat, depression, ridge, and valley, are considered in this study. This simulation were analysed with Ansys FLUENT 14.0 software package. The result showed the topography characteristics influence the value of pressure coefficient and streamlines especially when the house was located at ridge terrain. The findings strongly suggested that wind analysis should include all topographic features in the analysis in order to establish the true wind force exerted on any structure.

  9. An Analytical Method for Determining the Load Distribution of Single-Column Multibolt Connection

    Directory of Open Access Journals (Sweden)

    Nirut Konkong

    2017-01-01

    Full Text Available The purpose of this research was to investigate the effect of geometric variables on the bolt load distributions of a cold-formed steel bolt connection. The study was conducted using an experimental test, finite element analysis, and an analytical method. The experimental study was performed using single-lap shear testing of a concentrically loaded bolt connection fabricated from G550 cold-formed steel. Finite element analysis with shell elements was used to model the cold-formed steel plate while solid elements were used to model the bolt fastener for the purpose of studying the structural behavior of the bolt connections. Material nonlinearities, contact problems, and a geometric nonlinearity procedure were used to predict the failure behavior of the bolt connections. The analytical method was generated using the spring model. The bolt-plate interaction stiffness was newly proposed which was verified by the experiment and finite element model. It was applied to examine the effect of geometric variables on the single-column multibolt connection. The effects were studied of varying bolt diameter, plate thickness, and the plate thickness ratio (t2/t1 on the bolt load distribution. The results of the parametric study showed that the t2/t1 ratio controlled the efficiency of the bolt load distribution more than the other parameters studied.

  10. Energy efficiency in existing detached housing

    DEFF Research Database (Denmark)

    Gram-Hanssen, Kirsten; Christensen, Toke Haunstrup

    This memo is written as an input to the German project Enef-haus on energy- efficient restoration of single-family houses in Germany. The memo contains a summary of the Danish experiences divided into three main sections: first is a short historic overview of the Danish energy policy indicating...... when different relevant instruments have been introduced to increase the energy efficiency of privately owned single-family houses. Second is a short introduction to the Danish housing sector and its energy supplies. The third and main part of the report is an examination of the most recent...

  11. Radon levels in the 1988 Swedish housing stock

    International Nuclear Information System (INIS)

    Swedjemark, G.A.; Mellander, H.; Mjoenes, L.

    1993-01-01

    Radon levels have been measured in about 1300 randomly selected Swedish dwellings as part of a nation-wide energy and indoor climate study, ELIB. The measurements were performed in the heating season 1991-92 with alpha track detectors using an integration time of three months. In single-family houses the weighted mean was 141 Bq/m 3 (78 Bq/m 3 geometric) for the living area; for multi-family houses the corresponding values were 75 and 40 Bq/m 3 . More than 5% of the single-family houses and 1% of the dwellings in multi-family houses had levels above the action level for existing houses - 400 Bq/m 3 . Since 1981 Swedish building regulations have included limits on radon in new houses. The investigation shows that radon levels in houses built after 1981 are significantly lower than those in houses built before 1981. (orig.). (6 refs., 3 figs., 2 tabs.)

  12. What is a low-energy house and who cares?

    Energy Technology Data Exchange (ETDEWEB)

    Litt, B.R.

    1994-12-01

    Most energy analysts view low-energy houses as good things, yet differ in their expectations of what exactly a low energy house is. There are two intertwining threads to this report. The first is an evaluation of 50 buildings that have been claimed to be low-energy residences, for which monitored energy performance data have been collected. These data represent the preliminary effort in the ongoing update of the Buildings Energy-Use Compilation and Analysis (BECA) data base for new residences. The second thread concerns the definition of a low-energy house. After the elements of a definition are presented, their implications for actors involved in providing housing are identified. Several more tractable definitions are applied to the houses in this compilation. The outcomes illustrate ways in which different interests are served by various definitions. Different definitions can yield very different energy rankings. No single definition of a low-energy house is universally applicable.

  13. Replacing critical radiators to increase the potential to use low-temperature district heating – A case study of 4 Danish single-family houses from the 1930s

    DEFF Research Database (Denmark)

    Østergaard, Dorte Skaarup; Svendsen, Svend

    2016-01-01

    radiator sizes and heating demands in 4 existing Danish single-family houses from the 1930s. A year-long dynamic simulation was performed for each of the houses to evaluate the potential to lower the heating system temperatures. The results indicate that there is a large potential to use low......-temperature district heating in existing single-family houses. In order to obtain the full potential of low-temperature district heating, critical radiators must be replaced. Based on a novel method, a total of nine radiators were identified to be critical to ensure thermal comfort and low return temperatures in two...

  14. Behavior of single lap composite bolted joint under traction loading: Experimental investigation

    Science.gov (United States)

    Awadhani, L. V.; Bewoor, Anand

    2018-04-01

    Composite bolted joints are preferred connection in the composite structures to facilitate the dismantling for the replacements/ maintenance work. The joint behavior under tractive forces has been studied in order to understand the safety of the structure designed. The main objective of this paper is to investigate the behavior of single-lap joints in carbon fiber reinforced epoxy composites under traction loading conditions. The experiments were designed to identify the effect of bolt diameter, stacking sequence and loading rate on the properties of the joint. The experimental results show that the parameters influence the joint performance significantly.

  15. Biomechanical loading on the upper extremity increases from single key tapping to directional tapping.

    Science.gov (United States)

    Qin, Jin; Trudeau, Matthieu; Katz, Jeffrey N; Buchholz, Bryan; Dennerlein, Jack T

    2011-08-01

    Musculoskeletal disorders associated with computer use span the joints of the upper extremity. Computing typically involves tapping in multiple directions. Thus, we sought to describe the loading on the finger, wrist, elbow and shoulder joints in terms of kinematic and kinetic difference across single key switch tapping to directional tapping on multiple keys. An experiment with repeated measures design was conducted. Six subjects tapped with their right index finger on a stand-alone number keypad placed horizontally in three conditions: (1) on single key switch (the number key 5); (2) left and right on number key 4 and 6; (3) top and bottom on number key 8 and 2. A force-torque transducer underneath the keypad measured the fingertip force. An active-marker infrared motion analysis system measured the kinematics of the fingertip, hand, forearm, upper arm and torso. Joint moments for the metacarpophalangeal, wrist, elbow, and shoulder joints were estimated using inverse dynamics. Tapping in the top-bottom orientation introduced the largest biomechanical loading on the upper extremity especially for the proximal joint, followed by tapping in the left-right orientation, and the lowest loading was observed during single key switch tapping. Directional tapping on average increased the fingertip force, joint excursion, and peak-to-peak joint torque by 45%, 190% and 55%, respectively. Identifying the biomechanical loading patterns associated with these fundamental movements of keying improves the understanding of the risks of upper extremity musculoskeletal disorders for computer keyboard users. Copyright © 2010 Elsevier Ltd. All rights reserved.

  16. Moving loads on flexible structures presented in the floating frame of reference formulation

    Energy Technology Data Exchange (ETDEWEB)

    Hartweg, Stefan, E-mail: stefan.hartweg@web.de; Heckmann, Andreas, E-mail: andreas.heckmann@dlr.de [German Aerospace Center (DLR), Institute of System Dynamics and Control (Germany)

    2016-06-15

    The introduction of moving loads in the Floating Frame of Reference Formulation is presented. We derive the kinematics and governing equations of motion of a general flexible multibody system and their extension to moving loads. The equivalence of convective effects with Coriolis and centripetal forces is shown. These effects are measured numerically and their significance in moving loads traveling at high speed is confirmed. A method is presented to handle discontinuities when moving loads separate from the flexible structure. The method is extended from beam models to general flexible structures obtained by means of the Finite Element Method. An interpolation method for the deformation field of the modal representation of these bodies is introduced.The work is concluded by application of the method to modern mechanical problems in numerical simulations.

  17. Active house concept versus passive House

    NARCIS (Netherlands)

    Zeiler, W.; Boxem, G.; Vehler, R.; Verhoeven, M.; Fremouw, M.

    2009-01-01

    The passive house concept is the present trend in energy efficient sustainable dwellings. Within the passive house concept every effort is made to minimize the energy use. Substantial savings can be achieved by passive energy systems, especially natural ventilation, summer shading and winter solar

  18. A biomechanical comparison of tendon-bone interface motion and cyclic loading between single-row, triple-loaded cuff repairs and double-row, suture-tape cuff repairs using biocomposite anchors.

    Science.gov (United States)

    Barber, F Alan; Drew, Otis R

    2012-09-01

    To compare tendon-bone interface motion and cyclic loading in a single-row, triple-loaded anchor repair with a suture-tape, rip-stop, double-row rotator cuff repair. Using 18 human shoulders from 9 matched cadaveric pairs, we created 2 groups of rotator cuff repairs. Group 1 was a double-row, rip-stop, suture-tape construct. Group 2 was a single-row, triple-loaded construct. Before mechanical testing, the supraspinatus footprint was measured with calipers. A superiorly positioned digital camera optically measured the tendon footprint motion during 60° of humeral internal and external rotation. Specimens were secured at a fixed angle not exceeding 45° in reference to the load. After preloading, each sample was cycled between 10 N and 100 N for 200 cycles at 1 Hz, followed by destructive testing at 33 mm/s. A digital camera with tracking software measured the repair displacement at 100 and 200 cycles. Ultimate load and failure mode for each sample were recorded. The exposed anterior footprint border (6.5% ± 6%) and posterior footprint border (0.9% ± 1.7%) in group 1 were statistically less than the exposed anterior footprint border (30.3% ± 17%) and posterior footprint border (29.8% ± 14%) in group 2 (P = .003 and P row rotator cuff repair had greater footprint coverage, less rotational footprint displacement, and a greater mean ultimate failure load than the triple-loaded, single-row repair on mechanical testing. No double-row or single-row constructs showed 5 mm of displacement after the first 100 cycles. The most common failure mode for both constructs was suture tearing through the tendon. Differences in cuff fixation influence rotational tendon movement and may influence postoperative healing. Stronger repair constructs still fail at the suture-tendon interface. Copyright © 2012 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

  19. Strain evolution after fiber failure in a single-fiber metal matrix composite under cyclic loading

    Energy Technology Data Exchange (ETDEWEB)

    Hanan, Jay C. [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States)]. E-mail: jay.hanan@okstate.edu; Mahesh, Sivasambu [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Uestuendag, Ersan [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States)]. E-mail: ersan@caltech.edu; Beyerlein, Irene J. [Theoretical Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Swift, Geoffrey A. [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States); Clausen, Bjorn [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States); Brown, Donald W. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Bourke, Mark A.M. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2005-06-15

    The evolution of in situ elastic strain with cyclic tensile loading in each phase of a single Al{sub 2}O{sub 3}-fiber/aluminum-matrix composite was studied using neutron diffraction (ND). An analytical model appropriate for metal matrix composites (MMCs) was developed to connect the measured axial strain evolution in each phase with the possible micromechanical events that could occur during loading at room temperature: fiber fracture, interfacial slipping, and matrix plastic deformation. Model interpretation showed that the elastic strain evolution in the fiber and matrix was governed by fiber fracture and interface slipping and not by plastic deformation of the matrix, whereas the macroscopic stress-strain response of the composite was influenced by all three. The combined single-fiber composite model and ND experiment introduces a new and quick engineering approach for qualifying the micromechanical response in MMCs due to cyclic loading and fiber fracture.

  20. Strain evolution after fiber failure in a single-fiber metal matrix composite under cyclic loading

    International Nuclear Information System (INIS)

    Hanan, Jay C.; Mahesh, Sivasambu; Uestuendag, Ersan; Beyerlein, Irene J.; Swift, Geoffrey A.; Clausen, Bjorn; Brown, Donald W.; Bourke, Mark A.M.

    2005-01-01

    The evolution of in situ elastic strain with cyclic tensile loading in each phase of a single Al 2 O 3 -fiber/aluminum-matrix composite was studied using neutron diffraction (ND). An analytical model appropriate for metal matrix composites (MMCs) was developed to connect the measured axial strain evolution in each phase with the possible micromechanical events that could occur during loading at room temperature: fiber fracture, interfacial slipping, and matrix plastic deformation. Model interpretation showed that the elastic strain evolution in the fiber and matrix was governed by fiber fracture and interface slipping and not by plastic deformation of the matrix, whereas the macroscopic stress-strain response of the composite was influenced by all three. The combined single-fiber composite model and ND experiment introduces a new and quick engineering approach for qualifying the micromechanical response in MMCs due to cyclic loading and fiber fracture

  1. Evaluation of the Performance of Houses With and Without Supplemental Dehumidification in a Hot-Humid Climate

    Energy Technology Data Exchange (ETDEWEB)

    Kerrigan, P.; Norton, P.

    2014-10-01

    This report, Evaluation of the Performance of Houses with and without Supplemental Dehumidification in a Hot-Humid Climate, describes a research study that that was conducted by the Building Science Corporation (BSC) Building America Research Team. BSC seeks to research and report on the field monitoring of the performance of in-situ supplemental dehumidification systems in low energy, high performance, homes in a Hot-Humid climate. The purpose of this research project was to observe and compare the humidity control performance of new, single family, low energy, and high performance, homes. Specifically, the study sought to compare the interior conditions and mechanical systems operation between two distinct groups of houses, homes with a supplemental dehumidifier installed in addition to HVAC system, and homes without any supplemental dehumidification. The subjects of the study were ten single-family new construction homes in New Orleans, LA.Data logging equipment was installed at each home in 2012. Interior conditions and various end-use loads were monitored for one year. In terms of averages, the homes with dehumidifiers are limiting elevated levels of humidity in the living space. However, there was significant variation in humidity control between individual houses. An analysis of the equipment operation did not show a clear correlation between energy use and humidity levels. In general, no single explanatory variable appears to provide a consistent understanding of the humidity control in each house. Indoor humidity is likely due to all of the factors we have examined, and the specifics of how they are used by each occupant.

  2. Load Reduction, Demand Response and Energy Efficient Technologies and Strategies

    Energy Technology Data Exchange (ETDEWEB)

    Boyd, Paul A.; Parker, Graham B.; Hatley, Darrel D.

    2008-11-19

    The Department of Energy’s (DOE’s) Pacific Northwest National Laboratory (PNNL) was tasked by the DOE Office of Electricity (OE) to recommend load reduction and grid integration strategies, and identify additional demand response (energy efficiency/conservation opportunities) and strategies at the Forest City Housing (FCH) redevelopment at Pearl Harbor and the Marine Corps Base Hawaii (MCBH) at Kaneohe Bay. The goal was to provide FCH staff a path forward to manage their electricity load and thus reduce costs at these FCH family housing developments. The initial focus of the work was at the MCBH given the MCBH has a demand-ratchet tariff, relatively high demand (~18 MW) and a commensurate high blended electricity rate (26 cents/kWh). The peak demand for MCBH occurs in July-August. And, on average, family housing at MCBH contributes ~36% to the MCBH total energy consumption. Thus, a significant load reduction in family housing can have a considerable impact on the overall site load. Based on a site visit to the MCBH and meetings with MCBH installation, FCH, and Hawaiian Electric Company (HECO) staff, recommended actions (including a "smart grid" recommendation) that can be undertaken by FCH to manage and reduce peak-demand in family housing are made. Recommendations are also made to reduce overall energy consumption, and thus reduce demand in FCH family housing.

  3. [Loading and strength of single- and multi-unit fixed dental prostheses 2. Strength

    NARCIS (Netherlands)

    Baat, C. de; Witter, D.J.; Meijers, C.C.A.J.; Vergoossen, E.L.; Creugers, N.H.J.

    2014-01-01

    The ultimate strength of a dental prosthesis is defined as the strongest loading force applied to the prosthesis until afracture failure occurs. Important key terms are strength, hardness, toughness and fatigue. Relatively prevalent complications of single- and multi-unit fixed dental prostheses are

  4. 24 CFR 982.604 - SRO: Voucher housing assistance payment.

    Science.gov (United States)

    2010-04-01

    ... Types Single Room Occupancy (sro) § 982.604 SRO: Voucher housing assistance payment. (a) For a person... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false SRO: Voucher housing assistance payment. 982.604 Section 982.604 Housing and Urban Development Regulations Relating to Housing and Urban...

  5. City of Ljubljana: Its housing, population and housing conditions

    Directory of Open Access Journals (Sweden)

    Maša Filipovič

    2007-01-01

    Full Text Available The article gives an overview of key aspect of housing in Municipality of Ljubljana. The characteristics of households, of housing and their relation influence the housing situation in the city. Characteristic of housing refer mainly to quality of the dwellings, affordability and correspondence to the wishes of the inhabitants. The second important dimensions are households and their characteristics. In Europe and Slovenia increase in number of household can be observed, which in turn are becoming smaller. The housing policy has a role in establishing a balance between households and housing, i.e. ensuring that housing corresponds to the needs of individual households and to their number. For achieving this, knowledge and appropriate data are of vital importance. In the article we present the results of the Housing survey 2005. We observe housing conditions in a comparative perspective (Ljubljana in comparison to Maribor, Slovenia and selected European cities and according to three dimensions: housing fund, households and housing conditions.

  6. Phase Change Material (PCM Application in a Modernized Korean Traditional House (Hanok

    Directory of Open Access Journals (Sweden)

    Jaewook Lee

    2018-03-01

    Full Text Available Social and policy interest in the modernization and revitalization of the Korean traditional house (Hanok has increased recently in Korea but its low thermal performance is one of its weaknesses. A feasibility study was conducted to evaluate the suitability of a Phase Change Material (PCM in a modernized Hanok. The research method involved a test of the heating and cooling load reduction and Predicted Mean Vote (PMV analysis for human comfort using an Esp-r simulation adopting multi variable PCM types as the building wall composite. The influence of PCMs on reducing the building energy load was assessed as a criterion for upgrading materials and infiltration to the passive house regulation. Compared to the base case, the heating and cooling load reduction ratio were as follows: Case 1 (old-Hanok, 10%; Case 2 (Korean Building Act, 21%; and Case 3 (passive house regulation, 53%. The optimal phase change temperatures of the PCMs were Case 1 (24–26 °C, Case 2 (23–25 °C and Case 3 (24–26 °C. PMV analysis showed that the use of a PCM can narrow the comfort range and centralize the optimal point. Therefore, the following contents can be presented as the design and material guidelines. First, the optimal PCM temperature can vary according to the combination of materials and local climate. In addition, the infiltration and insulation should be verified and a certain portion of them should be secured. Finally, the addition of insulation to a passive house level should be considered actively using a PCM as a supplement for net zero energy building (nZEB.

  7. Cdc45-induced loading of human RPA onto single-stranded DNA.

    Science.gov (United States)

    Szambowska, Anna; Tessmer, Ingrid; Prus, Piotr; Schlott, Bernhard; Pospiech, Helmut; Grosse, Frank

    2017-04-07

    Cell division cycle protein 45 (Cdc45) is an essential component of the eukaryotic replicative DNA helicase. We found that human Cdc45 forms a complex with the single-stranded DNA (ssDNA) binding protein RPA. Moreover, it actively loads RPA onto nascent ssDNA. Pull-down assays and surface plasmon resonance studies revealed that Cdc45-bound RPA complexed with ssDNA in the 8-10 nucleotide binding mode, but dissociated when RPA covered a 30-mer. Real-time analysis of RPA-ssDNA binding demonstrated that Cdc45 catalytically loaded RPA onto ssDNA. This placement reaction required physical contacts of Cdc45 with the RPA70A subdomain. Our results imply that Cdc45 controlled stabilization of the 8-nt RPA binding mode, the subsequent RPA transition into 30-mer mode and facilitated an ordered binding to ssDNA. We propose that a Cdc45-mediated loading guarantees a seamless deposition of RPA on newly emerging ssDNA at the nascent replication fork. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

  8. Design and performance of a 2-megawatt high voltage dc test load

    International Nuclear Information System (INIS)

    Horan, D.; Kustom, R.; Ferguson, M.

    1994-01-01

    A high-power water-cooled resistive load which simulates the electrical load characteristics of a high-power klystron, capable of a 2 MW dissipation at 95 kV DC, is designed and installed. The load utilizes wirewound resistor elements suspended inside G-11 insulated tubing contained within a single-wall 316 stainless steel pressure vessel with flanged elliptical heads. The vessel supplies a continuous flow of deionized water. Baffles fabricated from G-10 sheets support the tubing and promote water turbulence to maximize heat removal. A companion oil tank houses resistive filament and mod-anode power supply test loads, plus an electrical interlock system which provides protection from inadequate water flow, excessive oil temperature, and arcing in either the pressure vessel or oil tank. A secondary safety system consists of both hydrostatic and steam pressure relief valves on the pressure vessel. Power supply tests indicate the load simulates the electrical load characteristics of a high-power klystron to a degree sufficient to accurately performance-test the rf high voltage power supplies used at the Advanced Photon Source

  9. A Prospective Study of Early Loaded Single Implant-Retained Mandibular Overdentures: Preliminary One-Year Results

    Directory of Open Access Journals (Sweden)

    Ali M. El-Sheikh

    2012-01-01

    Full Text Available Purpose. To investigate the predictability of simplifying mandibular overdenture treatment using one-stage surgery and early prosthetic loading of a single implant. Materials and Methods. Twenty edentulous patients with problematic existing mandibular dentures were treated. A single implant with a chemically modified surface (SLActive, Straumann AG, Basel, Switzerland was placed into the mandibular midline. The patients were recalled at 3, 6 and 12 months. Clinical assessments and marginal bone loss using standardized radiographs were recorded. All complications, failures and maintenance were noted. Visual analog-scale questionnaires were used to record patient satisfaction in five categories. ANOVA was used to determine differences between means of marginal bone loss and different categories of patient staisfaction (=0.05. Results. The 20 early loaded implants were all surviving at the 12-month recall. All implants showed less than 1 mm of marginal bone loss by the end of the 1-year with a significant increase during the follow-up period. Few prosthetic problems were reported. Patient satisfaction was high with a significant increase in all comfort and functional parameters. Conclusions. These preliminary 1-year results indicate that early loading of a single chemically modified surface implant used to retain a mucosa-borne mandibular overdenture is a safe, reliable, and cost-effective treatment.

  10. Partial Shading Detection in Solar System Using Single Short Pulse of Load

    Directory of Open Access Journals (Sweden)

    Bartczak Mateusz

    2017-03-01

    Full Text Available A single photovoltaic panel under uniform illumination has only one global maximum power point, but the same panel in irregularly illuminated conditions can have more maxima on its power-voltage curve. The irregularly illuminated conditions in most cases are results of partial shading. In the work a single short pulse of load is used to extract information about partial shading. This information can be useful and can help to make some improvements in existing MPPT algorithms. In the paper the intrinsic capacitance of a photovoltaic system is used to retrieve occurrence of partial shading.

  11. Laterally Loaded Single Pile Response Considering the Influence of Suction and Non-Linear Behaviour of Reinforced Concrete Sections

    Directory of Open Access Journals (Sweden)

    Stefano Stacul

    2017-12-01

    Full Text Available A hybrid BEM-p-y curves approach was developed for the single pile analysis with free/fixed head restraint conditions. The method considers the soil non-linear behaviour by means of p-y curves in series to a multi-layered elastic half-space. The non-linearity of reinforced concrete pile sections, also considering the influence of tension-stiffening, has been considered. The model reproduces the influence of suction by increasing the stress state and hence the stiffness of shallow soil-layers. Suction is modeled using the Modified-Kovacs model. The hybrid BEM-py curves method was validated by comparing results from data of 22 load tests on single piles. In addition, a detailed comparison is presented between measured and computed data on a large-diameter reinforced concrete bored single pile.

  12. Deterministic fabrication of dielectric loaded waveguides coupled to single nitrogen vacancy centers in nanodiamonds

    DEFF Research Database (Denmark)

    Siampour, Hamidreza; Kumar, Shailesh; Bozhevolnyi, Sergey I.

    We report on the fabrication of dielectric-loaded-waveguides which are excited by single-nitrogen-vacancy (NV) centers in nanodiamonds. The waveguides are deterministically written onto the pre-characterized nanodiamonds by using electron beam lithography of hydrogen silsesquioxane (HSQ) resist...... on silver-coated silicon substrate. Change in lifetime for NV-centers is observed after fabrication of waveguides and an antibunching in correlation measurement confirms that nanodiamonds contain single NV-centers....

  13. A comparison of plastic collapse and limit loads for single mitred pipe bends under in-plane bending

    International Nuclear Information System (INIS)

    Neilson, R.; Wood, J.; Hamilton, R.; Li, H.

    2010-01-01

    This paper presents a comparison of the plastic collapse loads from experimental in-plane bending tests on three 90 o single un-reinforced mitred pipe bends, with the results from various 3D solid finite element models. The bending load applied reduced the bend angle and in turn, the resulting cross-sectional ovalisation led to a recognised weakening mechanism. In addition, at maximum load there was a reversal in stiffness, characteristic of buckling. This reversal in stiffness was accompanied by significant ovalisation and plasticity at the mitre intersection. Both the weakening mechanism and the post-buckling behaviour are only observable by testing or by including large displacement effects in the plastic finite element solution. A small displacement limit solution with an elastic-perfectly plastic material model overestimated the collapse load by more than 40% and could not reproduce the buckling behaviour. The plastic collapse finite element solution, with large displacements, produced excellent agreement with the experiment. Sufficient experimental detail is presented for these results to be used as a benchmark for analysts in this area. Given the robustness of non-linear solutions in commercial finite element codes and the ready availability of computing resources, it is argued that pressure vessel code developers should now be recommending large displacement analysis as the default position for limit and plastic collapse analyses, rather than expecting engineers to anticipate weakening mechanisms and related non-linear phenomena.

  14. Immigration and Swiss House Prices

    OpenAIRE

    Kathrin Degen; Andreas M. Fischer

    2010-01-01

    This study examines the behavior of Swiss house prices to immigration flows for 85 districts from 2001 to 2006. The results show that the nexus between immigration and house prices holds even in an environment of low house price inflation, nationwide rent control, and modest immigration flows. An immigration inflow equal to 1% of an area's population is coincident with an increase in prices for single-family homes of about 2.7%: a result consistent with previous studies. The overall immigrati...

  15. Simulation and optimization study on a solar space heating system combined with a low temperature ASHP for single family rural residential houses in Beijing

    DEFF Research Database (Denmark)

    Deng, Jie; Tian, Zhiyong; Fan, Jianhua

    2016-01-01

    A pilot project of the solar water heating system combined with a low temperature air source heat pump (ASHP) unit was established in 2014 in a detached residential house in the rural region of Beijing, in order to investigate the system application prospect for single family houses via system...... optimization design and economic analysis. The established system was comprised of the glass heat-pipe based evacuated tube solar collectors with a gross area of 18.8 m2 and an ASHP with a stated heating power of 8 kW for the space heating of a single family rural house of 81.4 m2. The dynamic thermal...... with good building insulation were undertaken to figure out the system economical efficiency in the rural regions of Beijing. The results show that the payback periods of the solar space heating system combined with the ASHP with the collector areas 15.04-22.56 m2 are 17.3-22.4 years for the established...

  16. The design and analysis of single flank transmission error testor for loaded gears

    Science.gov (United States)

    Houser, D. R.; Bassett, D. E.

    1985-01-01

    Due to geometrical imperfections in gears and finite tooth stiffnesses, the motion transmitted from an input gear shaft to an output gear shaft will not have conjugate action. In order to strengthen the understanding of transmission error and to verify mathematical models of gear transmission error, a test stand that will measure the transmission error of a gear pair at operating loads, but at reduced speeds would be desirable. This document describes the design and development of a loaded transmission error tester. For a gear box with a gear ratio of one, few tooth meshing combinations will occur during a single test. In order to observe the effects of different tooth mesh combinations and to increase the ability to load test gear pairs with higher gear ratios, the system was designed around a gear box with a gear ratio of two.

  17. The Eco House

    Energy Technology Data Exchange (ETDEWEB)

    Hobbett, A. (Leicester Ecology Trust (United Kingdom))

    The Eco House is a former park keeper's lodge on the periphery of Leicester's largest public park. Taken over by Leicester Ecology Trust in 1990, the Eco House was a successor to the Trust's earlier low energy house. This has been a local authority decant house, retrofitted to show the potential for increased energy efficiency in older buildings. Many of the ideas from the earlier project were adopted by the new with a widening of its remit to include all matters of environmental concern connected with people's homes. So in addition to energy efficiency, other issues addressed include conservation of resources, wildlife, organic gardening, food production, water, environmental consumerism, recycling and health. Given that the use of energy is regarded by many environmentalists to be the single most important environmental issue today, and one which is easiest for households to address, it remains the project's dominant theme. (author)

  18. Does energy labelling on residential housing cause energy savings? Working paper

    Energy Technology Data Exchange (ETDEWEB)

    Kjaerbye, V.H.

    2008-12-15

    More than 80% of energy used in households is dedicated to space heating. Large potential energy savings have been identified in the existing housing stock. Energy labelling of single-family houses is seen as an important instrument to provide new house owners with information on efficient energy saving investments that can be made on the house. This paper evaluates the effects of the Danish Energy Labelling Scheme on energy consumption in existing single-family houses with propensity score matching using actual consumption of energy and register data describing the houses and households. We do not find significant energy savings due to the Danish Energy Labelling Scheme. (Author)

  19. A Comparison of Cats (Felis silvestris catus Housed in Groups and Single Cages at a Shelter: A Retrospective Matched Cohort Study

    Directory of Open Access Journals (Sweden)

    Malini Suchak

    2018-02-01

    Full Text Available The merits of various housing options for domestic cats in shelters have been debated. However, comparisons are difficult to interpret because cats are typically not able to be randomly assigned to different housing conditions. In the current study, we attempted to address some of these issues by creating a retrospective matched cohort of cats in two housing types. Cats in group housing (GH were matched with cats in single housing (SH that were the same age, sex, breed, coat color, and size. Altogether we were able to find a match for 110 GH cats. We compared these two groups on several measures related to their experience at the shelter such as moves and the development of behavioral problems. We also compared these groups on outcomes including length of stay, live release, and returns after adoption. We found that while the frequency of moves was similar in both groups, SH cats were more likely to be moved to offsite facilities than GH cats. SH cats also spent a smaller proportion of time on the adoption floor. Length of stay and, live release and returns after adoption did not significantly differ across groups, however GH cats were two times as likely to be returned after adoption. Future research should look at the behavioral impacts of shelter decision-making regarding moving and management of cats in different housing systems.

  20. Current wheeze, asthma, respiratory infections, and rhinitis among adults in relation to inspection data and indoor measurements in single-family houses in Sweden-The BETSI study.

    Science.gov (United States)

    Wang, J; Engvall, K; Smedje, G; Nilsson, H; Norbäck, D

    2017-07-01

    In the Swedish Building Energy, Technical Status and Indoor environment study, a total of 1160 adults from 605 single-family houses answered a questionnaire on respiratory health. Building inspectors investigated the homes and measured temperature, air humidity, air exchange rate, and wood moisture content (in attic and crawl space). Moisture load was calculated as the difference between indoor and outdoor absolute humidity. Totally, 7.3% were smokers, 8.7% had doctor' diagnosed asthma, 11.2% current wheeze, and 9.5% current asthma symptoms. Totally, 50.3% had respiratory infections and 26.0% rhinitis. The mean air exchange rate was 0.36/h, and the mean moisture load 1.70 g/m 3 . Damp foundation (OR=1.79, 95% CI 1.16-2.78) was positively associated while floor constructions with crawl space (OR=0.49, 95% CI 0.29-0.84) was negatively associated with wheeze. Concrete slabs with overlying insulation (OR=2.21, 95% CI 1.24-3.92) and brick façade (OR=1.71, 95% CI 1.07-2.73) were associated with rhinitis. Moisture load was associated with respiratory infections (OR=1.21 per 1 g/m 3 , 95% CI 1.04-1.40) and rhinitis (OR=1.36 per 1 g/m 3 , 95% CI 1.02-1.83). Air exchange rate was associated with current asthma symptoms (OR=0.85 per 0.1/h, 95% CI 0.73-0.99). Living in homes with damp foundation, concrete slabs with overlying insulation, brick façade, low ventilation flow, and high moisture load are risk factors for asthma, rhinitis, and respiratory infections. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  1. Social factors affect motor and anxiety behaviors in the animal model of attention-deficit hyperactivity disorders: A housing-style factor.

    Science.gov (United States)

    Tsai, Meng-Li; Kozłowska, Anna; Li, Yu-Sheng; Shen, Wen-Ling; Huang, Andrew Chih Wei

    2017-08-01

    The present study examines whether housing style (e.g., single housing, same-strain-grouped housing, and different-strain-grouped housing) and rat strain (e.g., spontaneous hypertension rats [SHR] and Wistar-Kyoto rats [WKY]) mediate motor function and anxiety behavior in the open field task. From week 4 through week 10 following birth, the rats were measured 30min for locomotor activity and anxiety once per week in the open field task. The SHR rats exhibited hyperactivity in total distance traveled and movement time to form the animal model of ADHD. The SHR rats spent more time inside the square and crossed the inside-outside line more often than the WKY rats, indicating the SHR rats exhibited less anxiety behavior. The different-strain-grouped housing style (but neither the same-strain-grouped housing style nor the single housing style) decreased total distance traveled and facilitated anxiety behavior. The motor function was negatively correlated with anxiety behavior for SHR rats but not for WKY rats. Housing styles had a negative correlation between motor function and anxiety behavior. The present findings provide some insights regarding how social factors (such as housing style) affect motor function and anxiety behavior related to ADHD in a clinical setting. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

  2. Advanced Controls for Residential Whole-House Ventilation Systems

    Energy Technology Data Exchange (ETDEWEB)

    Turner, William [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Walker, Iain [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sherman, Max [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2014-08-01

    Whole-house ventilation systems are becoming commonplace in new construction, remodeling/renovation, and weatherization projects, driven by combinations of specific requirements for indoor air quality (IAQ), health and compliance with standards, such as ASHRAE 62.2. Ventilation systems incur an energy penalty on the home via fan power used to drive the airflow, and the additional space-conditioning load associated with heating or cooling the ventilation air. Finding a balance between IAQ and energy use is important if homes are to be adequately ventilated while not increasing the energy burden. This study used computer simulations to examine RIVEC the Residential Integrated Ventilation Controller - a prototype ventilation controller that aims to deliver whole-house ventilation rates that comply with ventilation standards, for the minimum use of energy. Four different whole-house ventilation systems were simulated, both with and without RIVEC, so that the energy and IAQ results could be compared. Simulations were conducted for 13 US climate zones, three house designs, and three envelope leakage values. The results showed that the RIVEC controller could typically return ventilation energy savings greater than 40percent without compromising long-term chronic or short-term acute exposures to relevant indoor contaminants. Critical and average peak power loads were also reduced as a consequence of using RIVEC.

  3. Indoor climate in renovated and energy retrofitted social housing

    DEFF Research Database (Denmark)

    Knudsen, Henrik Nellemose; Jensen, Ole Michael

    2016-01-01

    The need for energy retrofitting of the Danish single-family houses is massive, especially for the high proportion of single-family houses built in the 1960s and 1970s. But even though the potential benefits are many, only few families embark on a major energy retrofit. There may be many reasons...... for this. An obvious one may be limited knowledge of non-energy benefits, e.g. in relation to the indoor climate. The objective of this study was to explain this limited effort to save energy by identifying barriers and incentives among house owners in relation to energy retrofitting of one’s own house....... Moreover, it was investigated among house owners, who had carried out energy retrofitting, whether a number of factors, including the perceived indoor climate, became better or worse after retrofitting. A questionnaire survey was carried out among 1,990 house owners in a municipality north of Copenhagen...

  4. Triple-Loaded Suture Anchors Versus a Knotless Rip Stop Construct in a Single-Row Rotator Cuff Repair Model.

    Science.gov (United States)

    Noyes, Matthew P; Lederman, Evan; Adams, Christopher R; Denard, Patrick J

    2018-05-01

    To compare the biomechanical properties of single-row repair with triple-loaded (TL) anchor repair versus a knotless rip stop (KRS) repair in a rotator cuff repair model. Rotator cuff tears were created in 8 cadaveric matched-pair specimens and repaired with a TL anchor or KRS construct. In the TL construct, anchors were placed in the greater tuberosity and then all suture limbs were passed through the rotator cuff as simple sutures and tied. In the KRS construct, a 2-mm suture tape was passed through the tendon in an inverted mattress fashion, and a free suture was passed medial to the suture tape to create a rip-stop. Then, the suture tape and free suture were secured with knotless anchors. Displacement was observed with video tracking after cyclic loading, and specimens were loaded to failure. The mean load to failure was 438 ± 59 N in TL anchor repairs compared with 457 ± 110 N in KRS repairs (P = .582). The mean displacement with cyclic loading was 3.8 ± 1.6 mm in TL anchor repairs versus 4.3 ± 1.8 mm in the KRS group (P = .297). Mode of failure was consistent in both groups, with 6 of 8 failures in the TL anchor group and 7 of 8 failures in KRS group occurring from anchor pullout. There is no statistical difference in load to failure and cyclic loading between TL anchor and KRS single-row repair techniques. KRS repair technique may be an alternative method of repairing full-thickness supraspinatus tendon tears with a single-row construct. Copyright © 2018 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

  5. Predicting downturns in the US housing market: a Bayesian approach [Conference presentation

    CSIR Research Space (South Africa)

    Gupta, R

    2008-10-01

    Full Text Available stream_source_info Gupta1_2008.pdf.txt stream_content_type text/plain stream_size 13351 Content-Encoding ISO-8859-1 stream_name Gupta1_2008.pdf.txt Content-Type text/plain; charset=ISO-8859-1 Background and Motivation... (Economics), University of Pretoria 2Senior Researcher (Statistics), CSIR, Pretoria. SASA 2008 Gupta and Das Predicting downturns in US housing market Background and Motivation Models - VARs, BVARs and SBVARs Forecasting House Prices in the Twenty...

  6. From Council Housing to Social Housing. The successes and misfortunes of Social Housing policies in Italy

    Directory of Open Access Journals (Sweden)

    Ferdinando Terranova

    2011-04-01

    Full Text Available The issues dealt with are three: the need for medium – and large – scale territorial planning; the quality of housing; the solutions to guarantee secure flows of financing to launch programmes of public residential housing (ERP. A premise of any ERP programme is the planning and construction of a fast rail network to guarantee mass mobility. Once this premise has been satisfied, it is possible to identify agricultural areas to be expropriated for ERP interventions. This programme is characterised by operating above the municipal level, and it requires a structure that has the administrative powers of an agency. As regards the quality of housing, the following equation has to be dispensed with: public residential housing = ugly building characterised by alienation and anomy. Planners from this century have been called on to rise the challenge. To be certain of obtaining finance for ERP programmes, the old road of contributions at source from workers should be pursued as well as the establishment of a single fund that gathers together all the financing foreseen by laws made over the years and not spent, set aside for ERP.

  7. Characterization of cyclic deformation behaviour of tempered and quenched 42CrMoS4 at single step and variable amplitude loading

    International Nuclear Information System (INIS)

    Schelp, M.; Eifler, D.

    2000-01-01

    Cyclic single steps tests were performed on tempered and quenched specimens of the steel 42CrMoS4. Strain, temperature and electrical resistance measurements yielded an empirical prediction of fatigue life according to Coffin, Manson and Morrow. All measured values are based on physical processes and therefore show a strong interaction. A new testing procedure was developed permitting hysteresis measurements to be used for the characterization and description of fatigue behaviour under variable amplitude loading. The basic idea is to combine fatigue tests with any kind of load spectrum with single step tests. This offers the possibility to apply lifetime prediction methods normally used for single step tests for those with random or service loading. (orig.)

  8. Estimation of historical earthquake intensities and intensity-PGA relationship for wooden house damages

    International Nuclear Information System (INIS)

    Choi, In-Kil; Seo, Jeong-Moon

    2002-01-01

    A series of tests and dynamic analyses on Korean traditional wooden houses was performed for the intensity estimation of the typical large historical earthquake records. Static and cyclic lateral load tests on the wooden frames were performed to assess the lateral load capacity of wooden frames. The shaking table tests on two 1:4 scaled models of a Korean ancient commoner's house made of fresh pine lumber were performed. Typical earthquake time histories recorded on soil and rock sites were used as input for the tests. The prototypical wooden house was analyzed for multiple time histories which match Ohsaki's ground response spectra. Seismic analyses comprise the aging of lumber and different soil condition. The relationship between the earthquake intensity and the peak ground acceleration (PGA) is proposed for the wooden house damages based on the results of this study. The intensity of major Korean historical earthquake records related with house collapses was quantitatively estimated to be MM VIII

  9. In-Migration and Housing Choice in Ho Chi Minh City: Toward Sustainable Housing Development in Vietnam

    Directory of Open Access Journals (Sweden)

    Ducksu Seo

    2017-09-01

    Full Text Available Since the initiation of Vietnam’s Doi Moi policy in 1986, the rate of urbanization has rapidly increased with a great influx of immigrants from rural areas. With such migration becoming a large acceleration factor for urban growth, the shortage of housing has become a critical problem in the cities. The Vietnamese government encouraged self-built housing and public–private partnerships to produce different types of housing stock. There are few available academic studies about housing choice in Vietnam to help understand movement dynamics and to foster sustainable housing development. The purpose of this study is to analyze housing choice and moving determinants in Ho Chi Minh City, and thereby establish recommendations for sustainable housing development in Vietnam. For an empirical study, a citizen questionnaire survey was conducted in HCMC and an in-depth analysis was carried out. The results indicate that the row house type for single-family housing is strongly preferred, but a preference for apartments is also observed for future planning. The factors influencing housing choice and movement are family income, housing ownership, housing typology, and commuting environment. These phenomena suggest that the government should prudently consider affordable housing development in many districts. The results of this study will help to establish policies for sustainable housing development in Ho Chi Minh City, Vietnam.

  10. Rental Housing Finance Survey

    Data.gov (United States)

    Department of Housing and Urban Development — The purpose of the RHFS is to provide current and continuous measure of the financial health and property characteristics of single-family and multifamily rental...

  11. Replacing critical radiators to increase the potential to use low-temperature district heating – A case study of 4 Danish single-family houses from the 1930s

    International Nuclear Information System (INIS)

    Østergaard, Dorte Skaarup; Svendsen, Svend

    2016-01-01

    Low-temperature district heating is a promising technology for providing homes with energy-efficient heating in the future. However, it is of great importance to maintain thermal comfort in existing buildings when district heating temperatures are lowered. This case study evaluated the actual radiator sizes and heating demands in 4 existing Danish single-family houses from the 1930s. A year-long dynamic simulation was performed for each of the houses to evaluate the potential to lower the heating system temperatures. The results indicate that there is a large potential to use low-temperature district heating in existing single-family houses. In order to obtain the full potential of low-temperature district heating, critical radiators must be replaced. Based on a novel method, a total of nine radiators were identified to be critical to ensure thermal comfort and low return temperatures in two of the case-houses. If these radiators were replaced it would be possible to lower the average heating system temperatures to 50 °C/27 °C in all four houses. - Highlights: • Comparison of dynamically calculated heat demands and radiator sizes. • Method for identification and evaluation of critical radiators was tested. • Existing houses can be heated with low-temperature heating for most of the year. • Replacing critical radiators helps ensure comfort and low return temperatures.

  12. Beyond nearly zero-energy buildings: Experimental investigation of the thermal indoor environment and energy performance of a single-family house designed for plus-energy targets

    DEFF Research Database (Denmark)

    Kazanci, Ongun Berk; Olesen, Bjarne W.

    2016-01-01

    A detached, one-story, single-family house in Denmark was operated with different heating and cooling strategies for 1 year. The strategies compared during the heating season were floor heating without ventilation, floor heating supplemented by warm air heating (ventilation system), and floor...... but it was not possible to reach the intended operative temperature when the outside temperatures were very low. During the cooling season, the cooling demand was high and overheating was a problem. Although the house was designed as a plus-energy house, it did not perform as one under the Danish climate conditions...

  13. Efficient Solutions for Existing Homes Case Study: Demonstration House of Cold-Climate Solutions for Affordable Housing

    Energy Technology Data Exchange (ETDEWEB)

    T. Schirber, C. Ojczyk, and R. Jacobson

    2016-05-01

    Single family homes in urban areas that are available for renovation by nonprofit developers are often in rough shape (1MM to 2MM nationally). Budgeting has historically focused on improving homes to meet basic housing standards. A rising interest in the long-term impact of homeownership has introduced the need to balance basic needs with home performance. This demonstration project aims to help nonprofit affordable housing developers become familiar with three Building America performance measures, the installation processes, and impacts and benefits of each. A story and a half home in North Minneapolis, MN was presented by Urban Homeworks our local nonprofit partner. The team helped them install three researched upgrade measures: exterior roof insulation or 'overcoat,' exterior foundation insulation, or 'excavationless', and a combined space and water heating HVAC system or 'combi.'

  14. A boundary element analysis on the influence of Krc and e/d on the performance of cyclically loaded single pile in clay

    Directory of Open Access Journals (Sweden)

    S. Basack

    Full Text Available The environment prevalent in oceans necessitates the piles supporting offshore structures to be designed against lateral cyclic loading initiated by wave action. Such quasi-static load reversal induces deterioration in the strength and stiffness of the soil-pile system, introducing progressive reduction in the bearing capacity associated with increased settlement of the pile foundation. To understand the effect of lateral cyclic load on axial response of single piles in soft clay, a numerical model was previously developed and validated by the author. Using the methodology, further analysis has been carried out to investigate how the variation in relative pilesoil stiffness and eccentricity effects the degradation of axial pile capacity due to the effect of lateral cyclic load. This paper presents a brief description of the methodology, analysis and interpretations of the theoretical results obtained from the further analysis and the relevant conclusions drawn there from.

  15. Non-intrusive appliance load monitoring system based on a modern kWh-meter

    Energy Technology Data Exchange (ETDEWEB)

    Pihala, H. [VTT Energy, Espoo (Finland). Energy Systems

    1998-12-01

    Non-intrusive appliance load monitoring (NIALM) is a fairly new method to estimate load profiles of individual electric appliances in a small building, like a household, by monitoring the whole load at a single point with one recording device without sub-meters. Appliances have special electrical characteristics, the positive and negative active and reactive power changes during the time they are switched on or off. These changes are called events and are detected with a monitoring device called an event recorder. Different NIALM-concepts developed in Europe and in the United States are generally discussed. The NIALM-concept developed in this study is based on a 3-phase, power quality monitoring kWh-meter and unique load identification algorithms. This modern kWh-meter with a serial data bus to a laptop personal computer is used as die event recorder. The NIALM-concept of this presentation shows for the first time how a kWh-meter can be used at the same time for billing, power quality and appliance end-use monitoring. An essential part of the developed NIALM-system prototype is the software of load identification algorithms which runs in an off-line personal computer. These algorithms are able to identify, with a certain accuracy, both two-state and multi-state appliances. This prototype requires manual-setup in which the naming of appliances is performed. The results of the prototype NIALMS were verified in a large, single family detached house and they were compared to the results of other prototypes in France and the United States, although this comparison is difficult because of different supply systems, appliance stock and number of tested sites. Different applications of NIALM are discussed. Gathering of load research data, verification of DSM-programs, home automation, failure analysis of appliances and security surveillance of buildings are interesting areas of NIALM. Both utilities and customers can benefit from these applications. It is possible to

  16. Nanodiamond Emitters of Single Photons

    Directory of Open Access Journals (Sweden)

    Vlasov I.I.

    2015-01-01

    Full Text Available Luminescence properties of single color centers were studied in nanodiamonds of different origin. It was found that single photon emitters could be realized even in molecularsized diamond (less than 2 nm capable of housing stable luminescent center “silicon-vacancy.” First results on incorporation of single-photon emitters based on luminescent nanodiamonds in plasmonic nanoantennas to enhance the photon count rate and directionality, diminish the fluorescence decay time, and provide polarization selectivity are presented.

  17. Housing's impact on wood products sales

    Science.gov (United States)

    Matt Bumgardner; Urs Buehlmann; Karen. Koenig

    2017-01-01

    What are the market conditions for woodworkers involved in construction-based sectors and what investments are planned to improve capabilities in the current business environment? For a fifth straight year, construction-based mar­kets continued their growth trends in 2016, as U.S. spending on single family housing, multi-family housing, and nonresidential construction...

  18. Optimal load scheduling in commercial and residential microgrids

    Science.gov (United States)

    Ganji Tanha, Mohammad Mahdi

    Residential and commercial electricity customers use more than two third of the total energy consumed in the United States, representing a significant resource of demand response. Price-based demand response, which is in response to changes in electricity prices, represents the adjustments in load through optimal load scheduling (OLS). In this study, an efficient model for OLS is developed for residential and commercial microgrids which include aggregated loads in single-units and communal loads. Single unit loads which include fixed, adjustable and shiftable loads are controllable by the unit occupants. Communal loads which include pool pumps, elevators and central heating/cooling systems are shared among the units. In order to optimally schedule residential and commercial loads, a community-based optimal load scheduling (CBOLS) is proposed in this thesis. The CBOLS schedule considers hourly market prices, occupants' comfort level, and microgrid operation constraints. The CBOLS' objective in residential and commercial microgrids is the constrained minimization of the total cost of supplying the aggregator load, defined as the microgrid load minus the microgrid generation. This problem is represented by a large-scale mixed-integer optimization for supplying single-unit and communal loads. The Lagrangian relaxation methodology is used to relax the linking communal load constraint and decompose the independent single-unit functions into subproblems which can be solved in parallel. The optimal solution is acceptable if the aggregator load limit and the duality gap are within the bounds. If any of the proposed criteria is not satisfied, the Lagrangian multiplier will be updated and a new optimal load schedule will be regenerated until both constraints are satisfied. The proposed method is applied to several case studies and the results are presented for the Galvin Center load on the 16th floor of the IIT Tower in Chicago.

  19. Steady-state crack growth in single crystals under Mode I loading

    DEFF Research Database (Denmark)

    Juul, Kristian Jørgensen; Nielsen, Kim Lau; Niordson, Christian Frithiof

    2017-01-01

    The active plastic zone that surrounds the tip of a sharp crack growing under plane strain Mode I loading conditions at a constant velocity in a single crystal is studied. Both the characteristics of the plastic zone and its effect on the macroscopic toughness is investigated in terms of crack tip...... that the largest shielding effect develops in HCP crystals, while the lowest shielding exists for FCC crystals. Rate-sensitivity is found to affect the plastic zone size, but the characteristics overall remain similar for each individual crystal structure. An increasing rate-sensitivity at low crack velocities...... shielding due to plasticity (quantified by employing the Suo, Shih, and Varias set-up). Three single crystals (FCC, BCC, HCP) are modelled in a steady-state elastic visco-plastic framework, with emphasis on the influence of rate-sensitivity and crystal structures. Distinct velocity discontinuities...

  20. Work Models in the Design Process for House Interior and Exterior: Physical or Virtual?

    Science.gov (United States)

    Bradecki, Tomasz; Uherek-Bradecka, Barbara

    2017-10-01

    The article presents the effects of research on different types of models of single family houses and multifamily houses. Exterior layout and interior functional layout are the main drivers for the final result of a design. Models are an important medium for presentation of architectural designs and play a pivotal role in explaining the first idea to people and potential clients. Although 3D models have unlimited possibilities of representation, some people cannot understand or ‘feel’ the designed space. The authors try to test how to combine the interior and the exterior in a single synthetic model. Several models of different houses have been presented in the article. All the case studies were developed with physical models, 3D models, and 2D hand sketches. The main focus of the work with the models was to achieve a coherent vision for future feeling of open space in designed houses. The research shows how synthetic models might be helpful in the design process. The research was carried in the URBAN model research group (urbanmodel.org, Gliwice, Poland) that consists of academic researchers and architects. The models reflect architectural experience gathered by the authors during their work on theoretical models, architectural projects and by supervision on site during construction site visits. Conclusions might be helpful for developers, architects, interior designers and architecture students.

  1. Effect of single-limb inertial loading on bilateral reaching: interlimb interactions.

    Science.gov (United States)

    Hatzitaki, V; McKinley, P

    2001-09-01

    This study employed the paradigm of asymmetric limb loading during bilateral arm reaching to examine the motor system's ability to independently organize the discrete movement of both upper limbs to equidistant targets when one of the limbs is loaded under specific timing constraints. The loading procedure involved attaching two different Velcro strapped weights to the right wrist, thus increasing the right arm's mass by 25% (1 kg) and 50% (2 kg). Movements were captured by a high-speed digital camera (240 Hz), while electromyographic (EMG) activity of selected elbow and shoulder muscles of both limbs was recorded (1,000 Hz) simultaneously. The results revealed that the mechanisms used by the system to compensate for unilateral limb loading were as follows: First, addition of an inertial load resulted in an increased movement time and concomitant decrease in peak velocity of both the upper arm and forearm of only the loaded limb and was scaled to the added weight. Second, for the EMG parameters, adjustments to the inertial load were primarily characterized by an increase in burst duration of all muscles, with load-specific changes in activity and onset time: the elbow antagonist (biceps) demonstrated a decrease in activity with the 50% load, and the elbow agonist (triceps) had an earlier onset with the 25% load. Concomitant adjustments on the unloaded limb consisted primarily of an increase in burst duration of the shoulder and elbow agonists (pectoralis and triceps), an earlier triceps onset solely with the 25% load, and a decrease in activity of the biceps solely with the 50% load. Third, with the exception of biceps activity, the amplitude of EMG activity was invariant across changes in load for both the loaded and unloaded limb. This lack of modulation in activity may have been related to the inability of performers to meet the time constraint of simultaneous bilateral limb arrival to the end targets. This inability can be the result of an active strategy

  2. Role of Inelastic Transverse Compressive Behavior and Multiaxial Loading on the Transverse Impact of Kevlar KM2 Single Fiber

    Directory of Open Access Journals (Sweden)

    Subramani Sockalingam

    2017-02-01

    Full Text Available High-velocity transverse impact of ballistic fabrics and yarns by projectiles subject individual fibers to multi-axial dynamic loading. Single-fiber transverse impact experiments with the current state-of-the-art experimental capabilities are challenging due to the associated micron length-scale. Kevlar® KM2 fibers exhibit a nonlinear inelastic behavior in transverse compression with an elastic limit less than 1.5% strain. The effect of this transverse behavior on a single KM2 fiber subjected to a cylindrical and a fragment-simulating projectile (FSP transverse impact is studied with a 3D finite element model. The inelastic behavior results in a significant reduction of fiber bounce velocity and projectile-fiber contact forces up to 38% compared to an elastic impact response. The multiaxial stress states during impact including transverse compression, axial tension, axial compression and interlaminar shear are presented at the location of failure. In addition, the models show a strain concentration over a small length in the fiber under the projectile-fiber contact. A failure criterion, based on maximum axial tensile strain accounting for the gage length, strain rate and multiaxial loading degradation effects are applied to predict the single-fiber breaking speed. Results are compared to the elastic response to assess the importance of inelastic material behavior on failure during a transverse impact.

  3. Pre-Design of Transitional Rural Housing for Syria with Recycled Rubble from Destroyed Buildings

    Science.gov (United States)

    Morishita, Naomi; Haj Ismail, Salah; Cetin, Rukiye

    2017-10-01

    The scale of destruction caused by seven years of on-going war in Syria has caused mass migration of the Syrian people within and outside of Syria. The situation calls for a means to provide the internally displaced persons (IDPs) within Syria with humane post-war affordable housing that can be quickly and easily built with few resources. Fossil fuel resources are not only scarce because of the war, but are also being used as a valuable commodity to finance the war economy, and thus, housing should minimize consumption of energy for heating and cooling because of the fossil fuel scarcity while providing high thermal comfort to the inhabitants. The housing parameters for the proposed solution are to integrate as much of the local building materials in the Aleppo region as possible using existing regional building traditions. Imported products such as building materials, machinery, equipment, as well as foreign labour and knowhow are to be kept to a minimum while incorporating recycled rubble from destroyed buildings. A comparative study of current disaster relief housing illustrates the appropriateness of each design solution in relation to the above-proposed housing parameters. A detailed analysis of the physical properties of an existing case study building in Dabiq, a town 40 km northeast of Aleppo, outlines the strengths and weaknesses of the building tradition to determine which aspects of the construction may be improved for better thermal comfort and resistance against earthquakes. The simulation results from WUFI Plus show the building behaviour of the case study house. This paper offers a concept for transitional single-family housing for IDPs based upon the adobe tradition in the rural areas of Aleppo. Reducing the heating and cooling loads can also drastically reduce fossil fuel requirements during the construction and operation phases of the single-family homes while maintaining a high level of indoor thermal comfort. Traditional construction techniques

  4. Estimation of Hedonic Single-Family House Price Function Considering Neighborhood Effect Variables

    Directory of Open Access Journals (Sweden)

    Chihiro Shimizu

    2014-05-01

    Full Text Available In the formulation of hedonic models, in addition to locational factors and building structures which affect the house prices, the generation of the omitted variable bias is thought to occur in cases when local environmental variables and the individual characteristics of house buyers are not taken into consideration. However, since it is difficult to obtain local environmental information in a small neighborhood unit and to observe individual characteristics of house buyers, these variables have not been sufficiently considered in previous studies. We demonstrated that non-negligible levels of omitted variable bias are generated if these variables are not considered.

  5. Modelling of phase change materials in the Toronto SUI net zero energy house using TRNSYS

    Energy Technology Data Exchange (ETDEWEB)

    Siddiqui, O.; Fung, A.; Zhang, D. [Ryerson Polytechnic Univ., Toronto, ON (Canada). Dept. of Mechanical and Industrial Engineering

    2008-08-15

    In the context of building applications, phase change materials (PCM), can be defined as any heat storage material that can absorb a large amount of thermal energy while undergoing a change in phase, such as from a solid to a liquid phase. The incorporation of PCM into the building envelope can enhance occupant comfort through the reduction of indoor temperature fluctuations. It has also been shown to cause a decrease in the overall energy consumption associated with the heating and cooling of buildings. This paper extended the analysis of the impact of using PCM, which has traditionally focused on homes of ordinary construction, to incorporate low to zero energy homes using a model of the Toronto net zero energy house developed in TRNSYS. The paper provided a description of the TRNSYS model/methodology, with reference to the wall layer used in the net zero energy house, and model of the layout of the net zero energy house in TRYNSYS. The TRYNSYS/type 204 PCM component was also presented along with the simulation results in terms of the temperature profile of the third floor of the net zero energy house on a typical winter day with varying PCM concentrations; the temperature profile of the third floor of the net zero energy house on a typical summer day with varying PCM concentrations; yearly heating/cooling load requirements of the net zero energy house for a variety of thermal mass used; temperature profile of the third floor of the net zero energy house on a typical summer day when PCM and concrete slab was used; yearly temperature profile of the third floor of the net zero energy house, illustrating the impact of using PCM; and the yearly heating/cooling load of the net zero energy house as the concentration of PCM was varied. It was concluded that the use of building integrated PCM can reduce temperature fluctuations considerably in the summer but only slightly in the winter. 16 refs., 1 tab., 8 figs.

  6. Experiences from the Design Processes of the First "Comfort Houses" in Denmark

    DEFF Research Database (Denmark)

    Brunsgaard, Camilla; Knudstrup, Mary-Ann; Heiselberg, Per

    2009-01-01

    The "Comfort Houses" is the most ambitious building project in passive houses in Denmark until today. Eight single family houses are built and designed by seven different consortiums. Besides fulfilling the German passive house standard the goal was to build the houses according to Danish tradition...

  7. Urban energy generation: The added value of photovoltaics in social housing

    International Nuclear Information System (INIS)

    Bahaj, A.S.; James, P.A.B.

    2007-01-01

    Social housing offers an alternative for low-to-medium income families and keyworkers (teachers, nurses, and police). In the United Kingdom (UK), this fairly priced, rental accommodation is normally owned by housing associations. This paper explores urban energy generation (micro-generation) focussing on photovoltaics (PV) and how its generated electricity can be used to provide added value in terms of demand reduction and contribute to a reduction in fuel poverty. It presents the results associated from in-depth monitoring of nine low-energy social housing units equipped with PV systems commissioned in 2004 in the South of England, UK. We report on energy load profiles and relate these to occupier behaviour and any changes in consumption that occur. The results highlight the impact of micro-generation showing a close correlation between occupant behaviour and energy consumption. Increased energy awareness can lead to changes in the way energy is used, reducing overall consumption but 'education' must be sustained to ensure long-term energy reductions. The financial benefit of operating high demand electrical appliances at the peak of the solar day as opposed to in the evening when overall demand on the central grid is higher is highlighted. The paper also draws conclusions allied to the challenges that PV micro-generation technology presents in the social housing context. (author)

  8. Environmental and economic performance of heating systems for energy-efficient dwellings: Case of passive and low-energy single-family houses

    International Nuclear Information System (INIS)

    Georges, L.; Massart, C.; Van Moeseke, G.; De Herde, A.

    2012-01-01

    In order to reduce the energy consumption of the building stock, a major trend is to drastically reduce the space-heating (SH) needs by improving the thermal performance of the envelope. In general, this measure is combined with efficient heating systems to minimize the delivered energy and greenhouse gas emissions. Nevertheless, these better systems are often more expensive so that the extra-investment could be hardly recovered for small-scale energy consumption. The main objective of the article is to show how equilibria between cost-effectiveness and environmental performance of heating systems are changed when small SH needs are considered (i.e. for passive and low-energy houses). The scope is limited to new single-family dwellings. Furthermore, the passive house standard provides means of simplifying the SH by using the ventilation air: the idea is that savings should counterbalance the extra-investment in super-insulation. In theory, a new global economic optimum is generated at the passive house level. The second objective of the work is to study which conditions could lead to this new optimum. Only a detached-house typology is investigated to address this last issue. Regarding methodology, all the investigations are done considering the Belgian context. Energy and environmental performance is evaluated using a method that complies with the EN-15603 and EN-15316 standards. - Highlights: ► Cost-benefit analysis is performed without incentives and is based on the Belgian market. ► Equilibria between cost-effectiveness and environmental performance of heating systems are changed for very low-energy houses. ► The space-heating simplification at the passive house level can hardly produce a new global economic optimum.

  9. A room of one's own: the SRO and the single elderly.

    Science.gov (United States)

    Crystal, S; Beck, P

    1992-10-01

    A survey of 485 single-room occupancy housing (SRO) residents in New York City found elderly residents strongly preferred to remain in centrally located neighborhoods where apartment housing was beyond their means; did not wish to share a housing unit; and had little confidence that they could find acceptable housing if they lost their present unit. For many elderly residents, SROs meet needs not easily met by available alternatives. Results suggest the need to maintain this housing option for older persons and replace losses that have accompanied gentrification in many central city areas.

  10. Randomized trial of the effects of housing assistance on the health and risk behaviors of homeless and unstably housed people living with HIV.

    Science.gov (United States)

    Wolitski, Richard J; Kidder, Daniel P; Pals, Sherri L; Royal, Scott; Aidala, Angela; Stall, Ron; Holtgrave, David R; Harre, David; Courtenay-Quirk, Cari

    2010-06-01

    Homelessness affects HIV risk and health, but little is known about the longitudinal effects of rental assistance on the housing status and health of homeless and unstably housed people living with HIV/AIDS. Homeless/unstably housed people living with HIV/AIDS (N = 630) were randomly assigned to immediate Housing Opportunities for People with AIDS (HOPWA) rental assistance or customary care. Self-reported data, CD4, and HIV viral load were collected at baseline, 6, 12, and 18 months. Results showed that housing status improved in both groups, with greater improvement occurring in the treatment group. At 18 months, 51% of the comparison group had their own housing, limiting statistical power. Intent-to-treat analyses demonstrated significant reductions in medical care utilization and improvements in self-reported physical and mental health; significant differential change benefiting the treatment group was observed for depression and perceived stress. Significant differences between homeless and stably housed participants were found in as-treated analyses for health care utilization, mental health, and physical health. HOPWA rental assistance improves housing status and, in some cases, health outcomes of homeless and unstably housed people living with HIV/AIDS.

  11. DOE-HUD initiative on energy efficiency in housing: A federal partnership

    Energy Technology Data Exchange (ETDEWEB)

    Brinch, J. [Energetics, Inc., Columbia, MD (United States); Ternes, M. [Oak Ridge National Lab., TN (United States); Myers, M. [USDOE, Washington, DC (United States)

    1996-07-01

    A five-year initiative between the US Department of Energy (DOE) and the US Department of Housing and Urban Development (HUD) demonstrated the feasibility of improving the energy efficiency of publicly-assisted housing. Twenty-seven projects and activities undertaken during 1990--95 involved research and field demonstrations, institutional and administrative changes to HUD policies and procedures, innovative financing and leveraging of federal dollars with non-federal money, and education, training, and technical assistance. With most of the 27 projects and activities completed, the two departments have initiated a five-year deployment effort, the DOE-Energy Partnerships for Affordable Homes, to achieve energy and water savings in public and assisted housing on a large scale throughout the country. A Clearinghouse for Energy Efficiency in Public and Assisted Housing managed by the National Center for Appropriate Technology (NCAT), will offer hands-on energy assistance to housing providers to complement DOE`s assistance. This paper presents the findings of the DOE-HUD Initiative, with primary attention paid to those projects which successfully integrated energy efficiency into private and public single and multifamily housing. The paper includes examples of the publications, case-study reports, exhibits and videotapes developed during the course of the Initiative. Information on the new DOE Energy Partnerships and on the NCAT Clearinghouse is also presented. New Partnership projects with the Atlanta and Chicago Housing Authorities describe the technical assistance envisioned under the Partnership.

  12. Analysis of the thermal behaviour of a low cost, single-family, more sustainable house in Porto Alegre, Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Grigoletti, Giane [Departamento de Arquitetura e Urbanismo, UFSM, Santa Maria, RS (Brazil); Nucleo Orientado para a Inovacao da Edificacao, UFRGS, Porto Alegre (Brazil); Sattler, Miguel A.; Morello, Alessandro [Nucleo Orientado para a Inovacao da Edificacao, UFRGS, Porto Alegre (Brazil)

    2008-07-01

    Efforts have been made in Brazil to improve the thermal performance of low-cost buildings. Since 1997 studies on low-cost housing have been developed by Nucleo Orientado para a Inovacao da Edificacao, the construction sector of the Engineering College of the Rio Grande do Sul University, Brazil. In 2000 a prototype of a low-cost house was built on the university campus. This prototype has undergone several evaluations in an attempt to assess its thermal and environmental performance, like: energy consumption, rainwater harvesting, use of sustainably managed wood for window frames and doors, besides a detailed accounting of overall costs. The thermal performance of the house was monitored, by recording outdoor and indoor air temperatures and relative humidity, over the period of whole year. A brief appraisal of such results, as well as the annual heating and cooling degree-hours are presented. Daily swings in outdoor are a common climatic event in Porto Alegre and the building response to daily temperature swings, greater than 10 K, and hot and cold spells are presented. The results show that the thermal performance of the prototype is fairly satisfactory, considering the limitations of a low-cost house, when artificial heating and cooling is not affordable. (author)

  13. Single Enteral Loading Dose of Phenobarbital for Achieving Its Therapeutic Serum Levels in Neonates

    Science.gov (United States)

    Turhan, Ali H.; Atici, Aytug; Okuyaz, Cetin; Uysal, Sercan

    2010-01-01

    Aim To investigate whether therapeutic serum drug levels may be achieved with a single enteral loading dose of phenobarbital. Methods The study was performed at the Mersin University Hospital in Turkey between April 2004 and August 2006, and included 29 newborn babies with seizure. After the acute treatment of the seizure with midazolam at a dose of 0.1 mg/kg, phenobarbital was administered by orogastric route at a loading dose of 20 mg/kg. Serum phenobarbital concentrations were measured at 0.5, 3, 6, and 12 hours after the loading. Serum phenobarbital levels between 10-30 μg/mL were considered as the therapeutic range. Results The serum phenobarbital levels reached therapeutic values in 9 (31%), 19 (66%), 21 (72%), and 23 (79%) patients at 0.5, 3, 6, and 12 hours after loading, respectively, while they did not reach therapeutic values in 6 patients (21%) after 12 hours. Four of the patients in whom there was no increase in serum phenobarbital levels had hypoxic-ischemic encephalopathy. Conclusion Enteral loading of phenobarbital can achieve therapeutic serum levels in the large majority of newborn babies with seizure and may be safely used in babies with the intact gastrointestinal tract. PMID:20564764

  14. Mass Housing Using GFRG Panels: A Sustainable, Rapid and Affordable Solution

    Science.gov (United States)

    Cherian, Philip; Paul, Shinto; Krishna, S. R. Gouri; Menon, Devdas; Meher Prasad, A.

    2017-06-01

    This work gives an overview of research and development carried out at IIT Madras, using glass fibre reinforced gypsum (GFRG) panels, to provide an innovative solution for rapid and affordable mass housing. The GFRG panels (124 mm thick), made from recycled industrial waste gypsum (from the fertilizer industry), are prefabricated in 3 m × 12 m sizes with cellular cavities inside, which can be filled with reinforced concrete wherever required and can be used as walls as well as floor slabs. The tests carried out (over the past 12 years) establish the performance of GFRG building systems to resist gravity and lateral loads as a load-bearing system (without beams and columns) in multi-storeyed buildings up to 8-10 storeys, with adequate strength, serviceability, durability and ductility. A two-storeyed four-apartment demonstration building has also been successfully constructed in the IIT Madras campus and presently a mass housing scheme (40 apartment units) using this technology is being demonstrated at Nellore. A structural design code has also been approved by the Bureau of Indian Standards, based on the extensive studies carried out on GFRG building systems.

  15. Buckling of Flat Thin Plates under Combined Loading

    Directory of Open Access Journals (Sweden)

    Ion DIMA

    2015-03-01

    Full Text Available This article aims to provide a quick methodology to determine the critical values of the forces applied to the central plane of a flat isotropic plate at which a change to the stable configuration of equilibrium occurs. Considering the variety of shapes, boundary conditions and loading combinations, the article does not intend to make an exhaustive presentation of the plate buckling. As an alternative, there will be presented only the most used configurations such as: rectangular flat thin plates, boundary conditions with simply supported (hinged or clamped (fixed edges, combined loadings with single compression or single shear or combination between them, compression and shear, with or without transverse loading, encountered at wings and control surfaces shell of fin and rudder or stabilizer and elevator. The reserve factor and the critical stresses will be calculated using comparatively two methods, namely the methodology proposed by the present article and ASSIST 6.6.2.0 – AIRBUS France software, a dedicated software to local calculations, for a simply supported plate under combined loading, compression on the both sides and shear.

  16. Cost effective multi-storey passive residential houses. Costs, technology, solutions, experiences of users; Kostenguenstige mehrgeschossige Passivwohnhaeuser. Kosten, Technik, Loesungen, Nutzererfahrungen

    Energy Technology Data Exchange (ETDEWEB)

    Schoeberl, Helmut

    2013-08-01

    Energy-efficient buildings in the range of single-family houses are no longer a rarity. The passive house technology and the costs are the significant barriers in the field of multi-storey housings. For the first time, the author of the book under consideration summarizes the planning tools, building envelope, building services, construction costs and the introduction of users by means of several passive house projects. The demands, components and challenges of the passive house are presented. Even experienced planners and decision-makers with get many detailed solutions and an accurate arrangement of additional costs.

  17. Location, location, location: Extracting location value from house prices

    OpenAIRE

    Kolbe, Jens; Schulz, Rainer; Wersing, Martin; Werwatz, Axel

    2012-01-01

    The price for a single-family house depends both on the characteristics of the building and on its location. We propose a novel semiparametric method to extract location values from house prices. After splitting house prices into building and land components, location values are estimated with adaptive weight smoothing. The adaptive estimator requires neither strong smoothness assumptions nor local symmetry. We apply the method to house transactions from Berlin, Germany. The estimated surface...

  18. Damage evolution analysis of coal samples under cyclic loading based on single-link cluster method

    Science.gov (United States)

    Zhang, Zhibo; Wang, Enyuan; Li, Nan; Li, Xuelong; Wang, Xiaoran; Li, Zhonghui

    2018-05-01

    In this paper, the acoustic emission (AE) response of coal samples under cyclic loading is measured. The results show that there is good positive relation between AE parameters and stress. The AE signal of coal samples under cyclic loading exhibits an obvious Kaiser Effect. The single-link cluster (SLC) method is applied to analyze the spatial evolution characteristics of AE events and the damage evolution process of coal samples. It is found that a subset scale of the SLC structure becomes smaller and smaller when the number of cyclic loading increases, and there is a negative linear relationship between the subset scale and the degree of damage. The spatial correlation length ξ of an SLC structure is calculated. The results show that ξ fluctuates around a certain value from the second cyclic loading process to the fifth cyclic loading process, but spatial correlation length ξ clearly increases in the sixth loading process. Based on the criterion of microcrack density, the coal sample failure process is the transformation from small-scale damage to large-scale damage, which is the reason for changes in the spatial correlation length. Through a systematic analysis, the SLC method is an effective method to research the damage evolution process of coal samples under cyclic loading, and will provide important reference values for studying coal bursts.

  19. Load requirements for maintaining structural integrity of Hanford single-shell tanks during waste feed delivery and retrieval activities

    International Nuclear Information System (INIS)

    JULYK, L.J.

    1999-01-01

    This document provides structural load requirements and their basis for maintaining the structural integrity of the Hanford Single-Shell Tanks during waste feed delivery and retrieval activities. The requirements are based on a review of previous requirements and their basis documents as well as load histories with particular emphasis on the proposed lead transfer feed tanks for the privatized vitrification plant

  20. Observation of martensitic structure evolution in Cu-Al-Ni single crystals with shape memory effect under external load using photoacoustic microscopy

    International Nuclear Information System (INIS)

    Muratikov, K.L.; Glazov, A.L.; Nikolaev, V.I.; Pul'nev, S.A.

    2006-01-01

    Photoacoustic microscopy is applied to observe the surface structure of Cu-Al-Ni shape-memory single crystals in both the loaded and unloaded states. Visualizing the early stages of the loading-induced martensitic transformation in Cu-Al-Ni single crystals is demonstrated to be feasible. The photoacoustic images are distinguished to advantage from the corresponding optical images by a higher contrast between different phases of the Cu-Al-Ni shape-memory alloy [ru

  1. Family dynamics and housing: Conceptual issues and empirical findings

    Directory of Open Access Journals (Sweden)

    Clara Mulder

    2013-09-01

    Full Text Available BACKGROUND In this reflection I discuss my conceptual ideas and the latest empirical findings regarding the connections between leaving the parental home, marriage, parenthood, and separation on the one hand, and housing on the other. I also discuss the limitations of the research and directions for future research. CONCLUSIONS Parental housing of good quality keeps specific categories of potential nest-leavers in the parental home, but is also positively associated with the likelihood of young adults starting their housing careers as homeowners. The connections between housing and marriage and between housing and parenthood can be characterized using the concepts of housing space, quality, and safety or security - all three of which married couples and families need more than singles - and flexibility, which couples and families need less. These four needs are strongly subject to social norms. There is a strong tendency for married couples and prospective families to move into home ownership and higher quality homes. Separation tends to lead ex-partners with lower moving costs and fewer resources to move from the joint home, and tends to lead to a longer lasting decrease in housing quality, particularly for women. Future research could focus on the impact of housing on the transformation of dating partnerships into co-residential partnerships, the impact of housing quality and home ownership on the quality of partner relationships, partnership and housing histories rather than single events and short-term effects, unraveling the causal connections between family and housing, and incorporating the impact of the socio-spatial context in the research.

  2. [Loading and strength of single- and multi-unit fixed dental prostheses. 1. Retention and resistance

    NARCIS (Netherlands)

    Baat, C. de; Witter, D.J.; Meijers, C.C.A.J.; Vergoossen, E.L.; Creugers, N.H.J.

    2014-01-01

    The degree to which single- and multi-unit fixed dental prostheses are able to withstand loading forces is dependent, among other things, on the quality of their retention and resistance. The quality of the retention and resistance of the configuration of an abutment tooth prepared for a metal and

  3. Twinning behavior in the Ti-5at.% Al single crystals during cyclic loading along [0001

    International Nuclear Information System (INIS)

    Xiao Lin

    2005-01-01

    Cyclic deformation behavior of Ti-5at.% Al single crystals subjected to pull-push cyclic load along [0001] crystallographic orientation was studied. A higher cyclic stress response was displayed in the Ti-5Al single crystal oriented for [0001] than that oriented for single prism slip. Optical microscopy and transmission electron microscopy examinations show that twinning is a dominant plastic deformation mode in the single crystals during cycling. Trace analysis of prepolished surfaces was used to identify the twin systems primarily responsible for deformation. The major twin type observed was {101-bar 2}, {112-bar 2}, {101-bar 1} and {112-bar 1}. slip was observed in the neighboring region of twins in the fatigued specimens. The activation of multiple twinning systems contributed to the higher cyclic saturation stress in Ti-5Al single crystals oriented for [0001

  4. Financial investments for zero energy houses

    DEFF Research Database (Denmark)

    Lepkova, Natalija; Zubka, Domantas; Jensen, Rasmus Lund

    2014-01-01

    The climate is constantly changing and is already affecting our future. The construction sector has become energy-intensive and a serious source of pollution. Today, houses use more energy and fossil fuels than ever before. In fact, buildings currently consume more than one-third of all energy......, but single-family houses should also be included in the renovation process and turned into zero energy buildings, which will be the standard in the near future of today’s construction sector. Read about the list of conclusions the investigations of a renovation project of a detached house into a nearzero...

  5. Calculated shielding factors for selected European houses

    International Nuclear Information System (INIS)

    Hedemann Jensen, P.

    1984-12-01

    Shielding factors for gamma radiation from activity deposited on structures and ground surfaces have been calculated with the computer model DEPSHIELD for single-family and multi-storey buildings in France, United Kingdom and Denmark. For all three countries it was found that the shielding factors for single-family houses are approximately a factor of 2 - 10 higher that those for buildings with five or more storeys. Away from doors and windows the shielding factors for French, British, and Danish single-family houses are in the range 0.03 - 0.1, 0.06 - 0.4, and 0.07 - 0.3, respectively. The uncertainties of the calculations are discussed and DEPSHIELD-results are compared with other methods as well as with experimental results. (author)

  6. Understanding of Danish passive houses based on pilot project Comfort Houses

    Energy Technology Data Exchange (ETDEWEB)

    Brunsgaard, C.

    2010-12-15

    The aim of the research is to investigate the notion of passive houses in Denmark. When this PhD thesis was initiated, the Danish building industry has just started to become interested in the passive house concept, but the knowledge was very limited. To be able to speed up the process of constructing Danish passive houses or other low energy concepts Saint-Gobain Isover Scandinavia took the initiative to the pilot project of the Comfort Houses, ten single-family houses constructed as passive houses, and wanted to share the knowledge with the building industry and other interested. This PhD thesis was a part of the strategy. If the concept of passive houses should be successfully promoted and achieve a significant sale in Denmark, it is believed that it is necessary to do a holistic approach. Besides energy savings and new structural solutions more qualitative aspects like architecture, everyday life and the future ways of living needs to be integrated in the future understanding of passive houses. This Ph.D. thesis therefore studies the following research question: What can the experience from the Comfort Houses enlighten about the future production and use of Danish passive houses? This understanding is achieved through studies of different study fields to be able to create a more holistic understanding of the concept both covering qualitative and quantitative analysis. The main focus will be on the study fields Design Process, Architecture and Everyday Life and the Indoor environment, which will answer the following sub-research questions: 1) How has the consortiums behind the Comfort Houses approached the design process according to teamwork, method and tools? And what barriers and possibilities lie within the approaches? 2) How do the occupants of the Comfort Houses experience the passive house architecture and the technical service systems? And has their everyday life changed by moving into a passive house? If so, how? 3) To what extent do the Comfort Houses

  7. Does stimulant use impair housing outcomes in low-demand supportive housing for chronically homeless adults?

    Science.gov (United States)

    Edens, Ellen L; Tsai, Jack; Rosenheck, Robert A

    2014-01-01

    Recent research suggests low-demand housing (i.e., not contingent upon abstinence) is effective in helping people exit homelessness, even among recent active substance users. Whether active users of illicit drugs and stimulants have worse housing outcomes than primary alcohol users, however, is unknown. A total of 149 participants in a multisite supportive housing program who reported high levels of active substance use at program entry were classified as either (1) predominantly "Alcohol Use" (>10 of 30 days alcohol, but not >10 days of drug use) or (2) "Illicit Drug Use" (>10 of 30 days any single illicit drug use with or without alcohol use). Sub-analysis of the "Illicit Drug Use" group compared participants reporting high levels of "Stimulant Use" (>10 days cocaine, crack, or methamphetamine use) to those with high levels of "Non-stimulant Use" (>10 days marijuana or other non-stimulant drug use). Group differences in housing outcomes were examined with mixed model multivariate regression. During 24-month follow-up, days housed increased dramatically for both the "Alcohol Use" and the "Illicit Drug Use" groups without significant differences. Sub-analysis of illicit drug users showed stimulant use was associated with fewer days housed (p = .01) and more days homeless (p = .02) over time. Among illicit drug users, stimulant users have somewhat less successful housing outcomes than other active drug and alcohol users, though both groups maintained substantial housing improvements in low-demand housing. © American Academy of Addiction Psychiatry.

  8. Evaluation of Structural Integrity for the Magazine Housing of Fuelling Machine

    International Nuclear Information System (INIS)

    Jua, Yong Sun; Han, Sung Bong; Chu, Jung Ho; Lee, Jeong Yoon; Kwak, Dae Il; Park, Tae Youn; Park, Wan Kyu; Lee, Kang Yong

    2009-01-01

    Wolsong NPP 1 which is the reactor type of the PHWR uses the natural uranium and has 380 fuel channels. For 100% power operation, the refueling is accomplished in-service. The fuel changing operation is based on the combined use of two remotely controlled fuelling machines (F/M), one operating on each end of a fuel channel. New fuel bundles, from one F/M, are inserted into a fuel channel in the same direction as the coolant flow and the displaced irradiated fuel bundles are received into the second F/M at the other end of the fuel channel. The F/M Magazine acts as a temporary storage area for fuel bundles and the various plugs in the F/M during refueling. It generates thermal and mechanical loads in the F/M Magazine. Together with seismic loads during seismic activity, these loads are considered in the Magazine design. In this paper, the evaluation of the structural integrity of the F/M Magazine housing is performed for Design, Test and Service condition loads given in the analysis requirement for the extended life time from 30 years to 50 years. The Magazine is classified as Safety Class 1. A stress analysis of the Magazine is carried out based on the requirements of the ASME Boiler and Pressure Vessel Code, Section III, Subsection NB, 1998 Edition with 1999 Addenda. The Magazine housing is made up of a thick cylindrical shell and is connected to the End cover at one end through 30' Grayloc clamp. The other end of the Magazine is clamped to the ram housing with a 10' Grayloc clamp. The material of construction of the magazine housing is ASME SA-182, F6a, class 2. The stress analysis is done by using the finite element method

  9. Static Load Distribution in Ball Bearings

    Science.gov (United States)

    Ricci, Mario

    2010-01-01

    A numerical procedure for computing the internal loading distribution in statically loaded, single-row, angular-contact ball bearings when subjected to a known combined radial and thrust load is presented. The combined radial and thrust load must be applied in order to avoid tilting between inner and outer rings. The numerical procedure requires the iterative solution of Z + 2 simultaneous nonlinear equations - where Z is the number of the balls - to yield an exact solution for axial and radial deflections, and contact angles. Numerical results for a 218 angular-contact ball bearing have been compared with those from the literature and show significant differences in the magnitudes of the ball loads, contact angles, and the extent of the loading zone.

  10. Early Loading of Single-Piece Implant for Partially Edentulous Posterior Arch: A Prospective One-Year Case Report

    Directory of Open Access Journals (Sweden)

    Amol Beldar

    2013-01-01

    Full Text Available Implant therapy is now well established, and there is an increasing need for shorter rehabilitation time. Original prerequisites of osseointegration have been reassessed to satisfy continuously increasing patient's expectation of reduced treatment time, improved esthetics, and increased comfort. Shorter healing time may be appropriate in some circumstances, and examples of early loading have been reported in animal and human studies. However, to date there are insufficient data to determine a universally acceptable opinion on early loading of implants for single-tooth replacement. This case report involves early loading, combined with construction of a restoration, inserted directly after 6 weeks of implant surgery and followup of one year.

  11. Synthesis of Single-Walled Carbon Nanotubes: Effects of Active Metals, Catalyst Supports, and Metal Loading Percentage

    Directory of Open Access Journals (Sweden)

    Wei-Wen Liu

    2013-01-01

    Full Text Available The effects of active metals, catalyst supports, and metal loading percentage on the formation of single-walled carbon nanotubes (SWNTs were studied. In particular, iron, cobalt, and nickel were investigated for SWNTs synthesis. Iron was found to grow better-quality SWNTs compared to cobalt and nickel. To study the effect of catalyst supports, magnesium oxide, silicon oxide, and aluminium oxide were chosen for iron. Among the studied supports, MgO was identified to be a suitable support for iron as it produced SWNTs with better graphitisation determined by Raman analysis. Increasing the iron loading decreased the quality of SWNTs due to extensive agglomeration of the iron particles. Thus, lower metal loading percentage is preferred to grow better-quality SWNTs with uniform diameters.

  12. Limit load solution for electron beam welded joints with single edge weld center crack in tension

    Science.gov (United States)

    Lu, Wei; Shi, Yaowu; Li, Xiaoyan; Lei, Yongping

    2012-05-01

    Limit loads are widely studied and several limit load solutions are proposed to some typical geometry of weldments. However, there are no limit load solutions exist for the single edge crack weldments in tension (SEC(T)), which is also a typical geometry in fracture analysis. The mis-matching limit load for thick plate with SEC(T) are investigated and the special limit load solutions are proposed based on the available mis-matching limit load solutions and systematic finite element analyses. The real weld configurations are simplified as a strip, and different weld strength mis-matching ratio M, crack depth/width ratio a/ W and weld width 2H are in consideration. As a result, it is found that there exists excellent agreement between the limit load solutions and the FE results for almost all the mis-matching ration M, a/ W and ligament-to-weld width ratio ( W-a)/ H. Moreover, useful recommendations are given for evaluating the limit loads of the EBW structure with SEC(T). For the EBW joints with SEC(T), the mis-matching limit loads can be obtained assuming that the components are wholly made of base metal, when M changing from 1.6 to 0.6. When M decreasing to 0.4, the mis-matching limit loads can be obtained assuming that the components are wholly made of base metal only for large value of ( W-a)/ H. The recommendations may be useful for evaluating the limit loads of the EBW structures with SEC(T). The engineering simplifications are given for assessing the limit loads of electron beam welded structure with SEC(T).

  13. 3D finite element analysis of immediate loading of single wide versus double implants for replacing mandibular molar

    Directory of Open Access Journals (Sweden)

    Shrikar R Desai

    2013-01-01

    Full Text Available Purpose: The purpose of this finite element study was to compare the stresses, strains, and displacements of double versus single implant in immediate loading for replacing mandibular molar. Materials and Methods: Two 3D FEM (finite element method models were made to simulate implant designs. The first model used 5-mm-wide diameter implant to support a single molar crown. The second model used 3.75-3.75 double implant design. Anisotropic properties were assigned to bone model. Each model was analyzed with single force magnitude (100 N in vertical axis. Results: This FEM study suggested that micromotion can be controlled better for double implants compared to single wide-diameter implants. The Von Mises stress for double implant showed 74.44% stress reduction compared to that of 5-mm implant. The Von Mises elastic strain was reduced by 61% for double implant compared to 5-mm implant. Conclusion: Within the limitations of the study, when the mesiodistal space for artificial tooth is more than 12.5 mm, under immediate loading, the double implant support should be considered.

  14. Housing as a Social Determinant of Health: Exploring the Relationship between Rent Burden and Risk Behaviors for Single Room Occupancy Building Residents.

    Science.gov (United States)

    Bowen, Elizabeth A; Mitchell, Christopher G

    2016-01-01

    A growing body of health determinants research recognizes that housing and health are intimately linked. This study explores the relationship between rent burden (the ratio of rent to income) and health risk behaviors among a sample of single room occupancy (SRO) building residents. Cross-sectional data were gathered from a sample of 162 residents living in privately owned, for-profit SROs in Chicago. Findings indicated that participants who had full rental subsidies and thus were designated in a no-rent-burden category were more likely to engage in risk behaviors including illicit drug use, having multiple sexual partners, and having sex without a condom, in comparison to participants with moderate or high-rent burdens. These findings suggest that interventions to increase housing stability and affordability and bolster reliable income sources (in addition to rental subsidies) may be key in reducing risk behaviors and improving health for vulnerably housed populations such as SRO residents.

  15. Transient hydrogen diffusion analyses coupled with crack-tip plasticity under cyclic loading

    International Nuclear Information System (INIS)

    Kotake, Hirokazu; Matsumoto, Ryosuke; Taketomi, Shinya; Miyazaki, Noriyuki

    2008-01-01

    The effect of hydrogen on the material strengths of metals is known as the hydrogen embrittlement, which affects the structural integrity of a hydrogen energy system. In the present paper, we developed a computer program for a transient hydrogen diffusion-elastoplastic coupling analysis by combining an in-house finite element program with a general purpose finite element computer program to analyze hydrogen diffusion. In this program, we use a hypothesis that the hydrogen absorbed in the metal affects the yield stress of the metal. In the present paper, we discuss the effects of the cyclic loading on the hydrogen concentration near the crack tip. An important finding we obtained here is the fact that the hydrogen concentration near the crack tip greatly depends on the loading frequency. This result indicates that the fatigue lives of the components in a hydrogen system depend not only on the number of loading cycles but also on the loading frequency

  16. Energy statistics for single-family houses, apartment buildings and non-residential premises in 2012; Energistatistik foer smaahus, flerbostadshus och lokaler 2012

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-07-01

    This report presents a summary of energy use and heating method in Swedish buildings (2012). The report covers basically three surveys - energy use in houses, in apartment buildings and premises. These three studies are first published separately. The results are then processed further, with the aim to provide a comprehensive picture of energy use in permanently occupied dwellings (houses and apartments) and commercial buildings (excluding industrial premises). This report presents the results of these operations.

  17. Housing aspiration in an informal urban settlement: A case study

    Directory of Open Access Journals (Sweden)

    Akunnaya P. OPOKO

    2015-11-01

    Full Text Available Housing aspiration is an important aspect of housing market analysis. However, there is a paucity of empirical research on housing aspiration among residents in informal settlements in developing countries. This study therefore investigated housing aspiration among the residents of Ayobo, Lagos, Nigeria. A cross-sectional survey of 1,151 households in Ayobo was conducted using a structured questionnaire as the data-collection instrument. The data were analysed using descriptive statistical and categorical regression analyses. The results show that a majority of the respondents were low-income earners living in rented and rooming-house types of accommodation. Around 73% of them expressed an intention to move to another residence, and 56% of this category of respondents intend to move into self-contained flats. The reasons for the planned relocation include poor condition of their present dwellings, changes in tenure status and household size, and the desire for exclusive use of facilities in their homes. In addition to these reasons, the waste-disposal method, sharing facilities, employment, and age and marital status of the residents emerged as the strongest predictors of housing aspiration among the respondents in the survey. This implies that, in order to meet the housing preferences and aspirations of residents in informal urban settlements in Nigeria, housing developers need to give adequate attention to the marital, age, employment and tenure status of the residents and place emphasis on developing affordable single-family houses and block of flats, as well as strategies for improving access to basic social amenities and services.

  18. Design and Evaluation of a Net Zero Energy Low-Income Residential Housing Development in Lafayette, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Dean, J.; VanGeet, O.; Simkus, S.; Eastment, M.

    2012-03-01

    This report outlines the lessons learned and sub-metered energy performance of an ultra low energy single family ranch home and duplex unit, called the Paradigm Pilot Project and presents the final design recommendations for a 153-unit net zero energy residential development called the Josephine Commons Project. Affordable housing development authorities throughout the United States continually struggle to find the most cost-effective pathway to provide quality, durable, and sustainable housing. The challenge for these authorities is to achieve the mission of delivering affordable housing at the lowest cost per square foot in environments that may be rural, urban, suburban, or within a designated redevelopment district. With the challenges the U.S. faces regarding energy, the environmental impacts of consumer use of fossil fuels and the increased focus on reducing greenhouse gas emissions, housing authorities are pursuing the goal of constructing affordable, energy efficient and sustainable housing at the lowest life-cycle cost of ownership. This report outlines the lessons learned and sub-metered energy performance of an ultra-low-energy single family ranch home and duplex unit, called the Paradigm Pilot Project and presents the final design recommendations for a 153-unit net zero energy residential development called the Josephine Commons Project. In addition to describing the results of the performance monitoring from the pilot project, this paper describes the recommended design process of (1) setting performance goals for energy efficiency and renewable energy on a life-cycle cost basis, (2) using an integrated, whole building design approach, and (3) incorporating systems-built housing, a green jobs training program, and renewable energy technologies into a replicable high performance, low-income housing project development model.

  19. Dual-task and anticipation impact lower limb biomechanics during a single-leg cut with body borne load.

    Science.gov (United States)

    Seymore, Kayla D; Cameron, Sarah E; Kaplan, Jonathan T; Ramsay, John W; Brown, Tyler N

    2017-12-08

    This study quantified how a dual cognitive task impacts lower limb biomechanics during anticipated and unanticipated single-leg cuts with body borne load. Twenty-four males performed anticipated and unanticipated cuts with and without a dual cognitive task with three load conditions: no load (∼6 kg), medium load (15% of BW), and heavy load (30% of BW). Lower limb biomechanics were submitted to a repeated measures linear mixed model to test the main and interaction effects of load, anticipation, and dual task. With body borne load, participants increased peak stance (PS) hip flexion (p = .004) and hip internal rotation (p = .001) angle, and PS hip flexion (p = .001) and internal rotation (p = .018), and knee flexion (p = .016) and abduction (p = .001) moments. With the dual task, participants decreased PS knee flexion angle (p biomechanical adaptations thought to increase risk of musculoskeletal injury, but neither anticipation nor dual task exaggerated those biomechanical adaptations. With a dual task, participants adopted biomechanics known to increase injury risk; whereas, participants used lower limb biomechanics thought to decrease injury risk during unanticipated cuts. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Performance enhancement of the single-phase series active filter by employing the load voltage waveform reconstruction and line current sampling delay reduction methods

    DEFF Research Database (Denmark)

    Senturk, O.S.; Hava, A.M.

    2011-01-01

    This paper proposes the waveform reconstruction method (WRM), which is utilized in the single-phase series active filter's (SAF's) control algorithm, in order to extract the load harmonic voltage component of voltage harmonic type single-phase diode rectifier loads. Employing WRM and the line...... current sampling delay reduction method, a single-phase SAF compensated system provides higher harmonic isolation performance and higher stability margins compared to the system using conventional synchronous-reference-frame-based methods. The analytical, simulation, and experimental studies of a 2.5 k...

  1. Performance of fuel cell for energy supply of passive house

    Energy Technology Data Exchange (ETDEWEB)

    Badea, G.; Felseghi, R. A., E-mail: Raluca.FELSEGHI@insta.utcluj.ro; Mureşan, D.; Naghiu, G. [Technical University of Cluj-Napoca, Building Services Engineering Department, Bd. December 21, no. 128-130, 400600, Cluj-Napoca (Romania); Răboacă, S. M. [National R& D Institute for Cryogenic and Isotopic Technologies, str. Uzinei, no. 4, Rm. Vălcea, 240050 (Romania); Aşchilean, I. [SC ACI Cluj SA, Avenue Dorobanţilor, no. 70, 400609, Cluj-Napoca (Romania)

    2015-12-23

    Hydrogen technology and passive house represent two concepts with a remarkable role for the efficiency and decarbonisation of energy systems in the residential buildings area. Through design and functionality, the passive house can make maximum use of all available energy resources. One of the solutions to supply energy of these types of buildings is the fuel cell, using this technology integrated into a system for generating electricity from renewable primary sources, which take the function of backup power (energy reserve) to cover peak load and meteorological intermittents. In this paper is presented the results of the case study that provide an analysis of the energy, environmental and financial performances regarding energy supply of passive house by power generation systems with fuel cell fed with electrolytic hydrogen produced by harnessing renewable energy sources available. Hybrid systems have been configured and operate in various conditions of use for five differentiated locations according to the main areas of solar irradiation from the Romanian map. Global performance of hybrid systems is directly influenced by the availability of renewable primary energy sources - particular geo-climatic characteristics of the building emplacement.

  2. Blur Detection is Unaffected by Cognitive Load.

    Science.gov (United States)

    Loschky, Lester C; Ringer, Ryan V; Johnson, Aaron P; Larson, Adam M; Neider, Mark; Kramer, Arthur F

    2014-03-01

    Blur detection is affected by retinal eccentricity, but is it also affected by attentional resources? Research showing effects of selective attention on acuity and contrast sensitivity suggests that allocating attention should increase blur detection. However, research showing that blur affects selection of saccade targets suggests that blur detection may be pre-attentive. To investigate this question, we carried out experiments in which viewers detected blur in real-world scenes under varying levels of cognitive load manipulated by the N -back task. We used adaptive threshold estimation to measure blur detection thresholds at 0°, 3°, 6°, and 9° eccentricity. Participants carried out blur detection as a single task, a single task with to-be-ignored letters, or an N-back task with four levels of cognitive load (0, 1, 2, or 3-back). In Experiment 1, blur was presented gaze-contingently for occasional single eye fixations while participants viewed scenes in preparation for an easy picture recognition memory task, and the N -back stimuli were presented auditorily. The results for three participants showed a large effect of retinal eccentricity on blur thresholds, significant effects of N -back level on N -back performance, scene recognition memory, and gaze dispersion, but no effect of N -back level on blur thresholds. In Experiment 2, we replicated Experiment 1 but presented the images tachistoscopically for 200 ms (half with, half without blur), to determine whether gaze-contingent blur presentation in Experiment 1 had produced attentional capture by blur onset during a fixation, thus eliminating any effect of cognitive load on blur detection. The results with three new participants replicated those of Experiment 1, indicating that the use of gaze-contingent blur presentation could not explain the lack of effect of cognitive load on blur detection. Thus, apparently blur detection in real-world scene images is unaffected by attentional resources, as manipulated by

  3. Annual experimental results on heat and cool storage modes for natural energy autonomous house, HARBEMAN house; Shizen energy jiritsu house (HARBEMAN house) no chikunetsu chikurei mode no jissoku kekka

    Energy Technology Data Exchange (ETDEWEB)

    Saito, T; Fujino, T; Suzuki, M [Tohoku University, Sendai (Japan)

    1997-11-25

    Outlined herein is performance of the solar system, followed for a year, installed in a solar house (HARBEMAN HOUSE) built in 1996 in City of Sendai. The house is equipped, on the roof, with a 30.42m{sup 2} wide solar collector on the south and sky radiator on the north. They are connected to a heat-insulated tank (31m{sup 3}) installed underground, storing hot or cool water which carries energy for heating/air-conditioning and hot water. The solar system operates in a long-term hot or cool water storage mode. In the hot water storage mode, the solar collector is connected to the underground main tank, where pumped-up water heated by solar heat is stored to be supplied as hot water. Heat collected is low during the December-February period, and recovered in March. In the cool water storage mode, the radiator is connected to the underground main tank, where pumped-up water is cooled by radiation and stored to be supplied to a fan coil unit in each room for air-conditioning. The recorded lowest temperature of water in the tank is 5.1degC. No air-conditioning load is observed, on account of the unseasonal weather. 3 refs., 10 figs., 2 tabs.

  4. TaC Studios New Construction Test House

    Energy Technology Data Exchange (ETDEWEB)

    Butler, T. [NAHB Research Center Industry Partnership, Upper Marlboro, MD (United States); Curtis, O. [NAHB Research Center Industry Partnership, Upper Marlboro, MD (United States); Kim, E. [NAHB Research Center Industry Partnership, Upper Marlboro, MD (United States); Roberts, S. [NAHB Research Center Industry Partnership, Upper Marlboro, MD (United States); Stephenson, R. [NAHB Research Center Industry Partnership, Upper Marlboro, MD (United States)

    2013-03-01

    As part of the NAHB Research Center Industry Partnership, Southface partnered with TaC Studios, an Atlanta based architecture firm specializing in residential and light commercial design, on the construction of a new test home in Atlanta, GA, in the mixed humid climate zone. This home will serve as a model home for the builder partner and addresses Building America energy savings targets through the planning and implementation of a design package will serve as a basis of design for the builder partner’s future homes. As a BA test house, this home will be evaluated to detail whole house energy use, end use loads, and HVAC and hot water efficiency.

  5. Creating Affordable Housing through self-management:

    DEFF Research Database (Denmark)

    Jensen, Jesper Ole; Stensgaard, Anne Gro

    The paper presents a case on self-management in the Danish social housing sector as a way of providing affordable housing. It is based on an evaluation of a Danish concept for affordable housing, Social Housing Plus (“AlmenBolig+”). The concept was introduced in 2007, and so far app 1.400 housing...

  6. Effect of Computerized Gloss Presentation Format on Reading Comprehension: A Cognitive Load Perspective

    Directory of Open Access Journals (Sweden)

    Farid Naserieh

    2016-09-01

    Full Text Available In recent years, gloss presentation format or the location where a gloss appears with respect to its related target word has received renewed attention. Research suggested that different gloss presentation formats could have differential effects on reading comprehension and/or vocabulary learning. This study hypothesized that the effectiveness of different computerized gloss presentation formats in reading comprehension could be explained by drawing on the split-attention effect within the framework of cognitive load theory. The effect predicts that when two related sources of information are physically separated (e.g., a target word and the respective gloss, cognitive resources are unnecessarily wasted, and learning is hindered. To test this hypothesis, 39 Persian-speaking L2 learners of English were divided into two experimental conditions, each being exposed to a text enhanced with either in-text or marginal glosses. Two measures of reading comprehension and three measures of cognitive load were employed. The participants’ initial differences in terms of grammatical knowledge and vocabulary size were balanced out, and their look-up behavior was also tracked. The results revealed that the participants with access to in-text glosses, compared with those with marginal glosses, experienced lower levels of cognitive load due to the elimination of split-attention and, accordingly, performed better on the reading com-prehension measures. Given the participants’ L2 proficiency level, the findings suggested that a text enhanced with in-text glosses tends to be instructionally more efficient.

  7. 75 FR 9247 - Single Family Mortgage Insurance Premium, Single Family

    Science.gov (United States)

    2010-03-01

    ... DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT [Docket No. FR-5376-N-13] Single Family Mortgage Insurance Premium, Single Family AGENCY: Office of the Chief Information Officer, HUD. ACTION: Notice... is soliciting public comments on the subject proposal. Lenders use the Single Family Premium...

  8. Changing attitudes toward house arrest with electronic monitoring: the impact of a single presentation?

    Science.gov (United States)

    Gainey, Randy R; Payne, Brian K

    2003-04-01

    The notion that community support is critical for program success is a consistent theme in the literature on community-based corrections. Unfortunately, many citizens know very little about alternative sanctions, are misinformed about them, and do not view them favorably. At issue is whether information about alternative sanctions affects individuals' attitudes regarding them. To address this question, students in an upper division criminal justice course were surveyed before and after a presentation on electronic monitoring. Following the presentation, students were more likely to agree that electronic monitoring is punitive and that it meets several goals of the justice system. Implications for policy makers and educators are provided.

  9. Coal-fired boiler houses in Cracow present state and possibilities to improve their efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Cyklis, P. [Institute of Industrial Equipment and Power Engineering, Cracow (Poland); Butcher, T.A. [Brookhaven National Lab., Upton, NY (United States)

    1995-12-31

    A significant amount of heat energy both for heating and process purposes is generated in Cracow, Poland in small-and medium size local boiler houses. The operating procedure of these boiler houses is most often economically and ecologically ineffective because of the bad condition of boilers and lack of funds to install automation, control and measurement equipment. Within the Polish-American Program of Elimination of Low Emission Sources financed by the US Department of Energy, the ENERGOEKSPERT Co., Ltd. investigated chosen boiler houses in Cracow, commissioned by the Cracow Development Office. The results of these investigations were subject of engineering analysis carried out at the Institute of Industrial Equipment and Power Engineering, Technical University, Cracow. The analysis proved that the low-cost improvement of economic efficiency and reduction of air pollutant emission is feasible for combustion of coal fuels.

  10. Post-war public housing in trouble : Papers presented at the Congress 'Post-war Public Housing in trouble', Delft, the Netherlands, October 4-5, 1984

    NARCIS (Netherlands)

    Prak, N.L.; Priemus, H.

    1985-01-01

    In a number of countries the social housing sector was given serious food for thought when some relatively new housing estates had to be demolished: Pruitt Igoe (St. Louis), Quarry Hills (Leeds), la Démocratie (Lyon), Linnaeusstraat (Leeuwarden, NL). The management of many other estates proves to be

  11. Emergency Department Referrals for Adolescent Urgent Psychiatric Consultation: Comparison of Clinical Characteristics of Repeat-presentations and Single-presentation.

    Science.gov (United States)

    Roberts, Nasreen; Nesdole, Robert; Hu, Tina

    2018-01-01

    a) to examine the demographic and clinical characteristics of repeat-presentations to an adolescent urgent psychiatric clinic, and b) to compare them with single-time presentation. This 18-month retrospective study compared repeat-presenters to age and gender matched single-time presenters. Demographic variables included age gender and ethnicity. Clinical variables included reason for referral, family history, diagnosis, recommendations and compliance. Data were analyzed using descriptive statistics, McNemar's Chi-square tests for matched pairs, and conditional logistic regression. Of 624 assessments 24% (N=151) were repeat-presentations. Compared with single-presentation, repeat-presentation group had a higher proportion of Aboriginal youth (X2 (1) = 108.28 p presentation group had higher odds of past hospital admission (OR: 3.50, p presentations for urgent psychiatric consultation constitute a quarter of referrals to the urgent psychiatric clinic. Identifying and addressing factors that contribute to repeat-presentations may, assist in improving treatment compliance by ensuring focused interventions and service delivery for these youth. In turn, this will improve access to the limited urgent services for other youth.

  12. Electrocortical and ocular indices of attention to fearful and neutral faces presented under high and low working memory load.

    Science.gov (United States)

    MacNamara, Annmarie; Schmidt, Joseph; Zelinsky, Gregory J; Hajcak, Greg

    2012-12-01

    Working memory load reduces the late positive potential (LPP), consistent with the notion that functional activation of the DLPFC attenuates neural indices of sustained attention. Visual attention also modulates the LPP. In the present study, we sought to determine whether working memory load might exert its influence on ERPs by reducing fixations to arousing picture regions. We simultaneously recorded eye-tracking and EEG while participants performed a working memory task interspersed with the presentation of task-irrelevant fearful and neutral faces. As expected, fearful compared to neutral faces elicited larger N170 and LPP amplitudes; in addition, working memory load reduced the N170 and the LPP. Participants made more fixations to arousing regions of neutral faces and faces presented under high working memory load. Therefore, working memory load did not induce avoidance of arousing picture regions and visual attention cannot explain load effects on the N170 and LPP. Copyright © 2012 Elsevier B.V. All rights reserved.

  13. Sonoma House. Monitoring of the First U.S. Passive House Retrofit

    Energy Technology Data Exchange (ETDEWEB)

    German, A. [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States); Weitzel, B. [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States); Backman, C. [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States); Hoeschele, M. [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States); Dakin, B. [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States)

    2012-12-01

    The Sonoma Deep Retrofit is a single-story deep retrofit project in the marine climate of Sonoma, California. The design was guided by Passive House principles that promote the use of very high levels of wall, ceiling, and floor insulation along with tight envelope construction to maintain a comfortable indoor environment with little or no need for conventional heating or cooling.

  14. Sonoma House: Monitoring of the First U.S. Passive House Retrofit

    Energy Technology Data Exchange (ETDEWEB)

    German, A.; Weitzel, B.; Backman, C.; Hoeschele, M.; Dakin, B.

    2012-12-01

    The Sonoma Deep Retrofit is a single-story deep retrofit project in the marine climate of Sonoma, California. The design was guided by Passive House principles which promote the use of very high levels of wall, ceiling, and floor insulation along with tight envelope construction to maintain a comfortable indoor environment with little or no need for conventional heating or cooling.

  15. Effects of Presentation Modes on Mobile-Assisted Vocabulary Learning and Cognitive Load

    Science.gov (United States)

    Lin, Chih-Cheng; Yu, Ya-Chuan

    2017-01-01

    Previous studies of multimedia presentations have determined the effects of the combination of text and pictures on vocabulary learning, but not those of the sound of new words. This study was intended to confirm those previous findings from the integration of mobile technologies and the approach of cognitive load. It adopted a within-subjects…

  16. Housing in Slovenia: An opportunity for quality shifts

    OpenAIRE

    Viktor Pust

    2000-01-01

    The limited quantity of new housing in Slovenia in the last decade and the recognised public interest for solving housing problems imply different procedures in providing adequate houses for various social groups. The article presents present development issues concerning housing development in Slovenia that lead to necessary additions to housing types. Simultaneously modernisation of planning documentation, amendments to the national housing programme and changes to the organisation structur...

  17. Vulnerability of housing buildings in Bucharest, Romania

    Science.gov (United States)

    Bostenaru, M.

    2009-04-01

    The author participates to the World Housing Encyclopedia project (www.world-housing.net), an internet based database of housing buildings in earthquake prone areas of the world. This is a voluntary project run by the Earthquake Engineering Research Institute, Oakland, California and the International Association of Earthquake Engineering, financial means being available only for the website where the information is shared. For broader dissemination in 2004 a summary publication of the reports to date was published. The database can be querried for various parameters and browsed after geographic distribution. Participation is open to any housing experts. Between 2003 and 2006 the author was also member of the editorial board. The author contributed numerous reports about building types in Romania, and each one about building types in Germany and Switzerland. This presentation will be about the contributed reports on building types in Romania. To the Encyclopedia eight reports on building types from Bucharest were contributed, while in further research of the author one more was similarly described regarding the vulnerability and the seismic retrofit. The selection of these types was done considering the historic development of the built substance in Bucharest from 1850 on, time from which a representative amount of housing buildings which can be classified in typologies can be found in Bucharest. While the structural types are not necessarily characteristic for the style, since the style has other time limits, often appearing before the type became common and then remaining being practiced also after another style gained ground, a historic succession can be seen also in this case. The nine types considered can be grouped in seven time categories: - the time 1850-1880, for a vernacular housing type with masonry load bearing walls and timber floors, - the time 1880-1920, for the type of two storey or multi-storey house with masonry walls and timber floors (in which

  18. Study on reduction of consumption and peak demand of electric power used in residential houses with solar heating and PV systems; Solar house no fuka heijunka to energy sakugen koka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Udagawa, M.; Endo, T. [Kogakuin University, Tokyo (Japan)

    1994-12-08

    A model house was simulated to reduce the consumption and peak demand for the photovoltaic power generation system, and solar heat air heating and hot water supply system in the solar house. As a type of construction, both wooden construction and reinforced concrete (RC) construction were selected with a total floor area of 125m{sup 2}. All the rooms were equipped with an air conditioner by heat pump from the air thermal source. A solar heat floor heater was simultaneously installed on the first floor. The hot water supply load was 4.8MWh per year. A commercial grid-connected on-site system was applied to the photovoltaic power generation with a 20m{sup 2} wide monocrystalline Si solar cell panel. As for the fluctuation in power load, the peak at the time of rising is more reduced in the RC house than in the wooden house, because the former is smaller in temperature fluctuation than the latter during the intermittence of air conditioning (as per the specified operational schedule). Therefore, the power is more leveled off in the former than in the latter. Between both, difference was hardly made in energy consumption per year. The ratio of dependency was 47% upon the photovoltaic power generation system, while it was 50% and 77%, under the air heating power load and hot water supply power load, respectively, upon the solar heat air heating and hot water supply system, so that both systems were considerably effective in saving the energy. 5 refs., 7 figs., 1 tab.

  19. Energy efficiency in existing detached housing. Danish experiences with different policy instruments

    Energy Technology Data Exchange (ETDEWEB)

    Gram-Hanssen, K.; Haunstrup Christensen, T. (Aalborg Univ., Danish Building Research Institute, Hoersholm (Denmark))

    2011-07-01

    This report contains a memo written as an input to the German project Enef-haus on energy-efficient restoration of single-family houses in Germany. The memo contains a summary of the Danish experiences divided into three main sections: first is a short historic overview of the Danish energy policy indicating when different relevant instruments have been introduced to increase the energy efficiency of privately owned single-family houses. Second is a short introduction to the Danish housing sector and its energy supplies. The third and main part of the report is an examination of the most recent and relevant instruments concluding both on the results concerning the impact of the instruments especially on owners of single-family houses and on more general experiences with their implementation. Finally the memo concludes on the general lessons that can be learned from the Danish experiences. (Author)

  20. Development of an Energy-Savings Calculation Methodology for Residential Miscellaneous Electric Loads: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Hendron, R.; Eastment, M.

    2006-08-01

    In order to meet whole-house energy savings targets beyond 50% in residential buildings, it will be essential that new technologies and systems approaches be developed to address miscellaneous electric loads (MELs). These MELs are comprised of the small and diverse collection of energy-consuming devices found in homes, including what are commonly known as plug loads (televisions, stereos, microwaves), along with all hard-wired loads that do not fit into other major end-use categories (doorbells, security systems, garage door openers). MELs present special challenges because their purchase and operation are largely under the control of the occupants. If no steps are taken to address MELs, they can constitute 40-50% of the remaining source energy use in homes that achieve 60-70% whole-house energy savings, and this percentage is likely to increase in the future as home electronics become even more sophisticated and their use becomes more widespread. Building America (BA), a U.S. Department of Energy research program that targets 50% energy savings by 2015 and 90% savings by 2025, has begun to identify and develop advanced solutions that can reduce MELs.

  1. Single dental implant retained mandibular complete dentures – influence of the loading protocol: study protocol for a randomized controlled trial

    Science.gov (United States)

    2014-01-01

    Background Over the years, there has been a strong consensus in dentistry that at least two implants are required to retain a complete mandibular denture. It has been shown in several clinical trials that one single median implant can retain a mandibular overdenture sufficiently well for up to 5 years without implant failures, when delayed loading was used. However, other trials have reported conflicting results with in part considerable failure rates when immediate loading was applied. Therefore it is the purpose of the current randomized clinical trial to test the hypothesis that immediate loading of a single mandibular midline implant with an overdenture will result in a comparable clinical outcome as using the standard protocol of delayed loading. Methods/design This prospective nine-center randomized controlled clinical trial is still ongoing. The final patient will complete the trial in 2016. In total, 180 edentulous patients between 60 and 89 years with sufficient complete dentures will receive one median implant in the edentulous mandible, which will retain the existing complete denture using a ball attachment. Loading of the median implant is either immediately after implant placement (experimental group) or delayed by 3 months of submerged healing at second-stage surgery (control group). Follow-up of patients will be performed for 24 months after implant loading. The primary outcome measure is non-inferiority of implant success rate of the experimental group compared to the control group. The secondary outcome measures encompass clinical, technical and subjective variables. The study was funded by the Deutsche Forschungsgemeinschaft (German research foundation, KE 477/8-1). Discussion This multi-center clinical trial will give information on the ability of a single median implant to retain a complete mandibular denture when immediately loaded. If viable, this treatment option will strongly improve everyday dental practice. Trial registration The trial

  2. Energy renovation services for single-family houses. Generalization and challenges of the one-stop-shop service model; Pientalojen energiaremonttipalvelut. Kokonaispalvelumallin yleistyminen ja sen haasteet

    Energy Technology Data Exchange (ETDEWEB)

    Paiho, S.; Kuusisto, J.; Stenlund, O.; Ala-Juusela, M.

    2012-08-15

    There are about 1.1 million single-family houses in Finland. 75% of these houses were built before year 1990. Majority of the houses remain at the energy- and eco-efficiency level of their construction time. If all of these houses were renovated to meet the state-of-the- art energy-efficiency requirements, the savings in nationwide consumption of heating energy would be 11.8 TWh. There are lots of typical single-family houses in the Finnish housing stock from the construction period. Renovation concepts with typical solutions can be developed for these typical houses. However, it must always be ensured that the selected concept suits the particular house. Comprehensive, full-service or one-stop-shop service models can be developed based on the renovation concepts. These may also include other services such as a building condition survey or a study, energy certificate, equipment and system installations, financial services, operation and maintenance services, and energy-monitoring and consumption analysis. It is natural to connect the one-stop-shop service model into the renovation process. The process includes stages for marketing, preliminary building inspection and energy audit, a detailed building inspection and energy analysis, a proposal for an integrated solution, the actual repair work, and quality assurance and continuous commissioning. Different stages involve different actors and service providers. There are several options for which type of organization or agent takes the main responsibility for the one-stop-shop service. Depending on the responsible organization, the content provider's business model and priorities differ. The one-stop-shop services business has been a narrow part of actors' whole business, so far. Some actors have already stopped providing the services, either due to the lack of demand or unprofitableness of the services. In an ideal model, the value promise and the main features of the model are the same, but the service

  3. Solar Living House Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Walters, Bradley [Univ. of Florida, Gainesville, FL (United States)

    2017-03-09

    The Solar Living House is a high-performance solar-powered dwelling designed by a team of faculty and students from the University of Florida, in collaboration with Santa Fe College, the National University of Singapore, and Alachua Habitat for Humanity. The project was designed in accordance with the Solar Decathlon 2015, a research, design, education, and outreach program developed by the U.S. Department of Energy (DOE). The Solar Living House is fundamentally a house for living, centered on people and the activities of daily life while quietly introducing advanced design, construction, and engineering technologies. The 993 square-foot two-bedroom one-bath home was designed to embrace and frame an exterior courtyard space. This courtyard acts as an extension of the interior living spaces, maximizing the spatial potentials of a modest building footprint and introducing natural light into the primary living spaces of the house. Research Outcomes: The Solar Living House advances work on high-performance buildings through three principal technological innovations: wet/dry modular construction, a building automation system, and solar dehumidification systems. Wet / Dry Modular Construction: The house is designed as a series of five modules, including one that is designated as the “wet core.” The wet core consolidates the mechanical systems and bathroom into a single module to reduce plumbing runs, efficiency losses, and on-site construction time. The other four modules are designed to eliminate interior load bearing walls to allow for maximum flexibility in the reconfiguring of the space over time. The modules are designed to meet the structural challenges of both Florida’s hurricanes and California’s earthquakes. Building Automation System: The house is equipped with an integrated building automation system, allowing the houses environmental systems, lights, security systems, and smoke detectors to be programmed, monitored, and controlled through any mobile

  4. Low cost earthquake resistant ferrocement small house

    International Nuclear Information System (INIS)

    Saleem, M.A.; Ashraf, M.; Ashraf, M.

    2008-01-01

    The greatest humanitarian challenge faced even today after one year of Kashmir Hazara earthquake is that of providing shelter. Currently on the globe one in seven people live in a slum or refugee camp. The earthquake of October 2005 resulted in a great loss of life and property. This research work is mainly focused on developing a design of small size, low cost and earthquake resistant house. Ferrocement panels are recommended as the main structural elements with lightweight truss roofing system. Earthquake resistance is ensured by analyzing the structure on ETABS for a seismic activity of zone 4. The behavior of structure is found satisfactory under the earthquake loading. An estimate of cost is also presented which shows that it is an economical solution. (author)

  5. Removal torque evaluation of three different abutment screws for single implant restorations after mechanical cyclic loading.

    Science.gov (United States)

    Paepoemsin, T; Reichart, P A; Chaijareenont, P; Strietzel, F P; Khongkhunthian, P

    2016-01-01

    The aim of this study was to evaluate the removal torque of three different abutment screws and pull out strength of implant-abutment connection for single implant restorations after mechanical cyclic loading. The study was performed in accordance with ISO 14801:2007. Three implant groups (n=15) were used: group A, PW Plus® with flat head screw; group B, PW Plus® with tapered screw; and group C, Conelog® with flat head screw. All groups had the same implant-abutment connection feature: cone with mandatory index. All screws were tightened with manufacturer's recommended torque. Ten specimens in each group underwent cyclic loading (1×106 cycles, 10 Hz, and 250 N). Then, all specimens were un-tightened, measured for the removal torque, and underwent a tensile test. The force that dislodged abutment from implant fixture was recorded. The data were analysed using independent sample t-test, ANOVA and Tukey HSD test. Before cyclic loading, removal torque in groups A, B and C were significantly different (B> A> C, Pabutment from implant fixture increased immensely after cyclic loading.

  6. Decentralized Method for Load Sharing and Power Management in a Hybrid Single/Three-Phase-Islanded Microgrid Consisting of Hybrid Source PV/Battery Units

    DEFF Research Database (Denmark)

    Karimi, Yaser; Oraee, Hashem; Guerrero, Josep M.

    2017-01-01

    This paper proposes a new decentralized power management and load sharing method for a photovoltaic based, hybrid single/three-phase islanded microgrid consisting of various PV units, battery units and hybrid PV/battery units. The proposed method is not limited to the systems with separate PV...... in different load, PV generation and battery conditions is validated experimentally in a microgrid lab prototype consisted of one three-phase unit and two single-phase units....

  7. 75 FR 29947 - Federal Home Loan Bank Housing Goals

    Science.gov (United States)

    2010-05-28

    ... performance of the Banks in meeting the housing goals under section 10C. 12 U.S.C. 1430c(e). Sections 1331... would measure the Banks' single-family housing goals performance relative to the actual goals-qualifying... advantages of comparing the Bank's performance to actual market performance outweigh the disadvantages. A...

  8. Using Whole-House Field Tests to Empirically Derive Moisture Buffering Model Inputs

    Energy Technology Data Exchange (ETDEWEB)

    Woods, J.; Winkler, J.; Christensen, D.; Hancock, E.

    2014-08-01

    Building energy simulations can be used to predict a building's interior conditions, along with the energy use associated with keeping these conditions comfortable. These models simulate the loads on the building (e.g., internal gains, envelope heat transfer), determine the operation of the space conditioning equipment, and then calculate the building's temperature and humidity throughout the year. The indoor temperature and humidity are affected not only by the loads and the space conditioning equipment, but also by the capacitance of the building materials, which buffer changes in temperature and humidity. This research developed an empirical method to extract whole-house model inputs for use with a more accurate moisture capacitance model (the effective moisture penetration depth model). The experimental approach was to subject the materials in the house to a square-wave relative humidity profile, measure all of the moisture transfer terms (e.g., infiltration, air conditioner condensate) and calculate the only unmeasured term: the moisture absorption into the materials. After validating the method with laboratory measurements, we performed the tests in a field house. A least-squares fit of an analytical solution to the measured moisture absorption curves was used to determine the three independent model parameters representing the moisture buffering potential of this house and its furnishings. Follow on tests with realistic latent and sensible loads showed good agreement with the derived parameters, especially compared to the commonly-used effective capacitance approach. These results show that the EMPD model, once the inputs are known, is an accurate moisture buffering model.

  9. TaC Studios New Construction Test House

    Energy Technology Data Exchange (ETDEWEB)

    Butler, T.; Curtis, O.; Kim, E.; Roberts, S.; Stephenson, R.

    2013-03-01

    As part of the NAHB Research Center Industry Partnership, Southface partnered with TaC Studios, an Atlanta based architecture firm specializing in residential and light commercial design, on the construction of a new test home in Atlanta, GA in the mixed humid climate zone. This home will serve as a model home for the builder partner and addresses Building America energy savings targets through the planning and implementation of a design package will serve as a basis of design for the builder partner's future homes. As a BA test house, this home will be evaluated to detail whole house energy use, end use loads, and HVAC and hot water efficiency.

  10. An evaluation of the installation of solar photovoltaic in residential houses in Malaysia: Past, present, and future

    International Nuclear Information System (INIS)

    Muhammad-Sukki, Firdaus; Ramirez-Iniguez, Roberto; Abu-Bakar, Siti Hawa; McMeekin, Scott G.; Stewart, Brian G.

    2011-01-01

    This paper examines solar energy development in Malaysia, particularly in relation to the installation of solar Photovoltaic (PV) in residential houses. It analyzes the past activities related to solar energy in Malaysia, in terms of research and developments (R and Ds), the implementations used as well as the national policies for the past 20 years which have pushed the installation of PV in the country. The Feed-In Tariff (FiT) scheme is discussed, showing comparative cost-benefit analysis between the PV installation in houses in the United Kingdom (UK) and Malaysia, and with other investment schemes available in Malaysia. To investigate the awareness of renewable energy policies and incentives, a preliminary survey of the public opinion in Malaysia has been carried out, and an evaluation of public willingness to invest in the FiT scheme by installing the PV on their houses is presented. The cost-benefit analysis shows that the proposed FiT programme is capable of generating good return on investment as compared to the one in the UK, but the return is lower than other investment tools. The survey suggests that most Malaysians are unaware of the government’s incentives and policies towards renewable energies, and are not willing to invest in the FiT scheme. - Highlights: ► Past activities related to solar energy is evaluated and FIT scheme is discussed. ► Financial analysis is presented; public perspective is evaluated. ► The FIT scheme generates higher return for PV installation in Malaysia than in the UK. ► The scheme, however, produces lower return than most investment schemes. ► Malaysians’ awareness levels are low and are not willing to invest in the FIT scheme.

  11. Improving the thermal integrity of new single-family detached residential buildings: Documentation for a regional database of capital costs and space conditioning load savings

    International Nuclear Information System (INIS)

    Koomey, J.G.; McMahon, J.E.; Wodley, C.

    1991-07-01

    This report summarizes the costs and space-conditioning load savings from improving new single-family building shells. It relies on survey data from the National Association of Home-builders (NAHB) to assess current insulation practices for these new buildings, and NAHB cost data (aggregated to the Federal region level) to estimate the costs of improving new single-family buildings beyond current practice. Space-conditioning load savings are estimated using a database of loads for prototype buildings developed at Lawrence Berkeley Laboratory, adjusted to reflect population-weighted average weather in each of the ten federal regions and for the nation as a whole

  12. House dust extracts contain potent immunological adjuvants

    NARCIS (Netherlands)

    Beukelman, C.J.; Dijk, H. van; Aerts, P.C.; Rademaker, P.M.; Berrens, L.; Willers, J.M.N.

    1987-01-01

    A crude aqueous extract of house dust and two house dust subfractions were tested for adjuvant activity in a sensitivity assay performed in mice. Evidence is presented that house dust contains at least two potent immunological adjuvants. One of these, present in both subfractions, was probably

  13. Ammonia emissions in tunnel-ventilated broiler houses

    Directory of Open Access Journals (Sweden)

    KAO Lima

    2011-12-01

    Full Text Available Gas production in broiler houses and their emissions are closely related to the microclimate established inside the house according to air temperature, humidity, and velocity. Therefore, the internal house environment is influenced by building typology and ventilation system. The objective of the present study was to evaluate ammonia emission rates in broiler houses equipped with different ventilation systems (negative or positive pressure and litter conditions (new or built-up. The environment of six commercial broiler houses was evaluated internal and external NH3 concentrations. Ventilation rates were recorded to estimate ammonia emission rates. The efficiency of circulation and exhaust fans was assessed, and higher ventilation rates were determined in negative-pressure houses due to the higher flow of the fans. Houses with new litter increased ammonia emission rates along the rearing period, indicating the relationship between gas emissions, bird age and ventilation rates, and presented a typical curve of NH3 emission increase. Negative-pressure houses with built-up litter presented higher emission rates during the first rearing week due to the high NH3 concentration during the brooding period, when the ventilation rates required to maintain chick thermal comfort are low. Although the results of the present study indicate an advantage of the positive-pressure systems as to gas emissions, further research is needed reduce gas emissions in broiler houses with negative-pressure systems.

  14. Application of Model Predictive Control for Active Load Management in a Distributed Power System with High Wind Penetration

    DEFF Research Database (Denmark)

    Zong, Yi; Kullmann, Daniel; Thavlov, Anders

    2012-01-01

    management. It also presents in detail how to implement a thermal model predictive controller (MPC) for the heaters' power consumption prediction in the PowerFlexHouse. It demonstrates that this MPC strategy can realize load shifting, and using good predictions in MPC-based control, a better matching...

  15. The Impact of Cognitive Load Theory on Learning Astronomy

    Science.gov (United States)

    Foster, Thomas M.

    2010-01-01

    Every student is different, which is the challenge of astronomy education research (AER) and teaching astronomy. This difference also provides the greatest goal for education researchers - our GUT - we need to be able to quantify these differences and provide explanatory and predictive theories to curriculum developers and teachers. One educational theory that holds promise is Cognitive Load Theory. Cognitive Load Theory begins with the well-established fact that everyone's working memory can hold 7 ± 2 unique items. This quirk of the human brain is why phone numbers are 7 digits long. This quirk is also why we forget peoples’ names after just meeting them, leave the iron on when we leave the house, and become overwhelmed as students of new material. Once the intricacies of Cognitive Load are understood, it becomes possible to design learning environments to marshal the resources students have and guide them to success. Lessons learned from Cognitive Load Theory can and should be applied to learning astronomy. Classroom-ready ideas will be presented.

  16. The autonomous house: a bio-hydrogen based energy self-sufficient approach.

    Science.gov (United States)

    Chen, Shang-Yuan; Chu, Chen-Yeon; Cheng, Ming-Jen; Lin, Chiu-Yue

    2009-04-01

    In the wake of the greenhouse effect and global energy crisis, finding sources of clean, alternative energy and developing everyday life applications have become urgent tasks. This study proposes the development of an "autonomous house" emphasizing the use of modern green energy technology to reduce environmental load, achieve energy autonomy and use energy intelligently in order to create a sustainable, comfortable living environment. The houses' two attributes are: (1) a self-sufficient energy cycle and (2) autonomous energy control to maintain environmental comfort. The autonomous house thus combines energy-conserving, carbon emission-reducing passive design with active elements needed to maintain a comfortable environment.

  17. Overheating risk barriers to energy renovations of single family houses

    DEFF Research Database (Denmark)

    Psomas, Theofanis Ch.; Heiselberg, Per Kvols; Duer, Karsten

    2016-01-01

    Highlights •Energy renovations of houses in moderate climates increase overheating risk. •Critical measures are the floor insulation and the improvement of the airtightness. •Decrease of the g value of windows diminishes the intensity and the period of it. •Static method of assessment shows highe...

  18. Reunifying Families, Cutting Costs: Housing-Child Welfare Partnerships for Permanent Supportive Housing

    Science.gov (United States)

    Harburger, Deborah S.; White, Ruth A.

    2004-01-01

    In the absence of an adequate supply of affordable, quality housing, child welfare agencies are placed in the unenviable position of separating families to protect children from the debilitating effects of homelessness. This article presents recommendations for cost-effective housing-child welfare partnerships that will shift the burden of…

  19. Physical scale modeling of single free head piles under lateral loading in cohesive soils

    Directory of Open Access Journals (Sweden)

    Edgar Leonardo Salamanca-Medina

    2017-06-01

    Full Text Available This paper presents the results of the small scale modeling of free head wood piles under horizontal loading in cohesive soils, tested in order to compare the results with analytical models proposed by various authors. Characteristic Load (CLM and P-Y Curves methods were used for the prediction of lateral deflections at the head of the piles and the method proposed by Broms for estimating the ultimate lateral load. These predictions were compared with the results of the physical modeling, obtaining a good approximation between them.

  20. Peptide-loaded dendritic cells prime and activate MHC-class I-restricted T cells more efficiently than protein-loaded cross-presenting DC

    DEFF Research Database (Denmark)

    Met, Ozcan; Buus, Søren; Claesson, Mogens H

    2003-01-01

    -pulsed DC. Moreover, SIINFEKL-loaded DC were up to 50 times more efficient than DC-pulsed with OVA-protein for generation of an H-2K(b)-restricted response. Immunization of mice with SIINFEKL-loaded DC resulted in a much stronger H-2K(b)-restricted response than immunization with OVA-pulsed DC. These data......Undifferentiated and differentiated dendritic cells (uDC and dDC, respectively), derived from the bone marrow, were studied in vitro and in vivo. Ovalbumin (OVA) and two OVA-derived peptides binding to H-2K(b) and I-A(b), respectively, were used. Two IL-2 secreting T cell hybridomas specific...... for the OVA-derived epitopes were used in the in vitro read-out. The ability to cross-present the H-2K(b) binding OVA(257-264)-peptide (SIINFEKL) was restricted to dDC, which express CD11c(+), CD86(+), and MHC-II(+). In vitro, the antigenicity of SIINFEKL-loaded DC declined at a slower rate than that of OVA...

  1. Optimization of Boiler Heat Load in Water-Heating Boiler-House

    Directory of Open Access Journals (Sweden)

    B. A. Bayrashevsky

    2009-01-01

    Full Text Available An analytical method for optimization of water-heating boiler loads has been developed on the basis of approximated semi-empirical dependences pertaining to changes of boiler gross efficiency due to its load. A complex (∂tух/∂ξΔξ is determined on the basis of a systematic analysis (monitoring of experimental data and the Y. P. Pecker’s formula for calculation of balance losses q2. This complex makes it possible to set a corresponding correction to a standard value of the boiler gross efficiency due to contamination of heating surfaces.Software means for optimization of water-heating boilers has been developed and it is recommended to be applied under operational conditions.

  2. A social philosophy of housing

    OpenAIRE

    King, Peter

    2003-01-01

    This book presents an original perspective by opening up housing to a philosophical approach. It fully integrates discussions on contemporary housing policy and social philosophy in a manner not previously attempted in the housing literature. Professor Jim Kemeny (Uppsala University) described it as ‘the first systematic application of social philosophy from an individual choice perspective’.

  3. Assessment of implantable infusion pumps for continuous infusion of human insulin in rats: potential for group housing

    DEFF Research Database (Denmark)

    Jensen, Vivi Flou Hjorth; Molck, Anne-Marie; Martensson, Martin

    2017-01-01

    compound in these studies, and a comparator model of persistent exposure by HI infusion from external pumps has recently been developed to support toxicological evaluation of long-acting insulin analogues. However, this model requires single housing of the animals. Developing an insulin-infusion model...... which allows group housing would therefore greatly improve animal welfare. The aim of the present study was to investigate the suitability of implantable infusion pumps for HI infusion in group-housed rats. Group housing of rats implanted with a battery-driven pump proved to be possible. Intravenous...... infusion of HI lowered blood glucose levels persistently for two weeks, providing a comparator model for use in two-week repeated-dose toxicity studies with new long-acting insulin analogues, which allows group housing, and thereby increasing animal welfare compared with an external infusion model....

  4. Usefulness of in-house PCR methods for hepatitis B virus DNA detection.

    Science.gov (United States)

    Portilho, Moyra Machado; Baptista, Marcia Leite; da Silva, Messias; de Sousa, Paulo Sérgio Fonseca; Lewis-Ximenez, Lia Laura; Lampe, Elisabeth; Villar, Livia Melo

    2015-10-01

    The aim of the present study was to evaluate the performance of three in-house PCR techniques for HBV DNA detection and compare it with commercial quantitative methods to evaluate the usefulness of in-house methods for HBV diagnosis. Three panels of HBsAg reactive sera samples were evaluated: (i) 50 samples were examined using three methods for in-house qualitative PCR and the Cobas Amplicor HBV Monitor Assay; (ii) 87 samples were assayed using in-house semi-nested PCR and the Cobas TaqMan HBV test; (iii) 11 serial samples obtained from 2 HBV-infected individuals were assayed using the Cobas Amplicor HBV test and semi-nested PCR. In panel I, HBV DNA was detected in 44 samples using the Cobas Amplicor HBV test, 42 samples using semi-nested PCR (90% concordance with Cobas Amplicor), 22 samples using PCR for the core gene (63.6% concordance) and 29 samples using single-round PCR for the pre-S/S gene (75% concordance). In panel II, HBV DNA was quantified in 78 of the 87 HBsAg reactive samples using Cobas TaqMan but 52 samples using semi-nested PCR (67.8% concordance). HBV DNA was detected in serial samples until the 17th and 26th week after first donation using in-house semi-nested PCR and the Cobas Amplicor HBV test, respectively. In-house semi-nested PCR presented adequate concordance with commercial methods as an alternative method for HBV molecular diagnosis in low-resource settings. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Some Environmental and Economic Aspects of Energy Saving Measures in Houses. An estimation model for total energy consumption and emissions to air from the Norwegian dwelling stock, and a life cycle assessment method for energy saving measures in houses

    Energy Technology Data Exchange (ETDEWEB)

    Myhre, L

    1995-12-01

    Motivated by the need to reduce the total energy consumption and the environmental load from society, this doctoral thesis discusses energy conservation measures on existing houses. Alternative additional thermal insulation measures are assessed using an interdisciplinary life cycle approach. The first task is to develop an interdisciplinary assessment method for building improvement measures, taking account of energy consumption, resource consumption, emissions to air of environmentally harmful gases, and economic costs during the entire life cycle of the building. The second task is to develop an estimation model for the total energy consumption and emissions to air of environmentally harmful gases from the dwelling stock of Norway. Finally, the third task is to assess the total energy saving potential and the total environmental benefits of energy saving measures in houses on a national level, including only life cycle analyses of additional thermal insulation measures on single houses. Chap 2 describes the dwelling stock in Norway. Chaps 3 and 4 present an estimation model for total energy consumption and emissions to air from the dwelling stock, and calculations using the model. Chaps 5 and 6 propose and use a calculation method for the assessment of additional thermal insulation measures, using a ``cradle-to-grave`` approach. Since hydroelectric power is the main energy source in this sector in Norway, estimated payback periods for emissions to air are long. But hydroelectric power saved in this sector may be used to obtain reduction in fossil fuel use in other sectors as discussed in Chap 7. Some of the topics discussed are further elaborated on in appendices. 107 refs., 39 figs, 88 tabs.

  6. Reactive bonding mediated high mass loading of individualized single-walled carbon nanotubes in an elastomeric polymer

    Science.gov (United States)

    Zhao, Liping; Li, Yongjin; Qiu, Jishan; You, Jichun; Dong, Wenyong; Cao, Xiaojun

    2012-09-01

    A reactive chemical bonding strategy was developed for the incorporation of a high mass loading of individual single-wall carbon nanotubes (SWCNTs) into an elastomeric matrix using a reactive ionic liquid as a linker. This method simultaneously prevented the agglomeration of SWCNTs and caused strong interfacial bonding, while the electronic properties of the SWCNTs remained intact. As a result, the high conductivity of the carbon nanotubes (CNTs) and the flexibility of the elastomeric matrix were retained, producing optimum electrical and mechanical properties. A composite material with a loading of 20 wt% SWCNTs was fabricated with excellent mechanical properties and a high conductivity (9500 S m-1). The method could be used to form transparent thin conductive films that could tolerate over 800 bend cycles at a bending angle of 180° while maintaining a constant sheet resistance.A reactive chemical bonding strategy was developed for the incorporation of a high mass loading of individual single-wall carbon nanotubes (SWCNTs) into an elastomeric matrix using a reactive ionic liquid as a linker. This method simultaneously prevented the agglomeration of SWCNTs and caused strong interfacial bonding, while the electronic properties of the SWCNTs remained intact. As a result, the high conductivity of the carbon nanotubes (CNTs) and the flexibility of the elastomeric matrix were retained, producing optimum electrical and mechanical properties. A composite material with a loading of 20 wt% SWCNTs was fabricated with excellent mechanical properties and a high conductivity (9500 S m-1). The method could be used to form transparent thin conductive films that could tolerate over 800 bend cycles at a bending angle of 180° while maintaining a constant sheet resistance. Electronic supplementary information (ESI) available: Conductivity test of the SEBS-SWCNTs film, transmission spectra and sheet resistance for the spin-coated SEBS-SWCNTs thin films on PET slides. See DOI: 10

  7. Building America Case Study: Demonstration House of Cold-Climate Solutions for Affordable Housing, Minneapolis, Minnesota

    Energy Technology Data Exchange (ETDEWEB)

    2016-05-01

    Single family homes in urban areas that are available for renovation by nonprofit developers are often in rough shape (1MM to 2MM nationally). Budgeting has historically focused on improving homes to meet basic housing standards. A rising interest in the long-term impact of homeownership has introduced the need to balance basic needs with home performance. This demonstration project aims to help nonprofit affordable housing developers become familiar with three Building America performance measures, the installation processes, and impacts and benefits of each. A story and a half home in North Minneapolis, MN was presented by Urban Homeworks our local nonprofit partner. The team helped them install three researched upgrade measures: exterior roof insulation or 'overcoat,' exterior foundation insulation, or 'excavationless', and a combined space and water heating HVAC system or 'combi'. To maximize efficiency of application and to address budget issues, the Team worked with Urban Homeworks to identify ways to use volunteers and construction training programs to install the measures. An open invitation to visit the job site was extended to other nonprofit developers and industry partners to encourage dialog about the systems during live installation.

  8. NorthernSTAR 1-1/2-Story Demonstration House of Cold Climate Solutions for Affordable Housing

    Energy Technology Data Exchange (ETDEWEB)

    Schirber, T. [Univ. of Minnesota, St. Paul, MN (United States). NorthernSTAR Building America Partnership; Ojczyk, C. [Univ. of Minnesota, St. Paul, MN (United States). NorthernSTAR Building America Partnership; Jacobson, R. [Univ. of Minnesota, St. Paul, MN (United States). NorthernSTAR Building America Partnership

    2016-03-01

    Single family homes in urban areas that are available for renovation by nonprofit developers are often in rough shape (1MM to 2MM nationally). Budgeting has historically focused on improving homes to meet basic housing standards. A rising interest in the long-term impact of homeownership has introduced the need to balance basic needs with home performance. This demonstration project aims to help nonprofit affordable housing developers become familiar with three Building America performance measures, the installation processes, and impacts and benefits of each. A story and a half home in North Minneapolis, MN was presented by Urban Homeworks our local nonprofit partner. The team helped them install three researched upgrade measures: exterior roof insulation or 'overcoat,' exterior foundation insulation, or 'excavationless', and a combined space and water heating HVAC system or 'combi'. To maximize efficiency of application and to address budget issues, the Team worked with Urban Homeworks to identify ways to use volunteers and construction training programs to install the measures. An open invitation to visit the job site was extended to other nonprofit developers and industry partners to encourage dialog about the systems during live installation.

  9. Refining Housing, Husbandry and Care for Animals Used in Studies Involving Biotelemetry

    Science.gov (United States)

    Hawkins, Penny

    2014-01-01

    Simple Summary Biotelemetry, the remote detection and measurement of an animal function or activity, is widely used in animal research. Biotelemetry devices transmit physiological or behavioural data and may be surgically implanted into animals, or externally attached. This can help to reduce animal numbers and improve welfare, e.g., if animals can be group housed and move freely instead of being tethered to a recording device. However, biotelemetry can also cause pain and distress to animals due to surgery, attachment, single housing and long term laboratory housing. This article explains how welfare and science can be improved by avoiding or minimising these harms. Abstract Biotelemetry can contribute towards reducing animal numbers and suffering in disciplines including physiology, pharmacology and behavioural research. However, the technique can also cause harm to animals, making biotelemetry a ‘refinement that needs refining’. Current welfare issues relating to the housing and husbandry of animals used in biotelemetry studies are single vs. group housing, provision of environmental enrichment, long term laboratory housing and use of telemetered data to help assess welfare. Animals may be singly housed because more than one device transmits on the same wavelength; due to concerns regarding damage to surgical sites; because they are wearing exteriorised jackets; or if monitoring systems can only record from individually housed animals. Much of this can be overcome by thoughtful experimental design and surgery refinements. Similarly, if biotelemetry studies preclude certain enrichment items, husbandry refinement protocols can be adapted to permit some environmental stimulation. Nevertheless, long-term laboratory housing raises welfare concerns and maximum durations should be defined. Telemetered data can be used to help assess welfare, helping to determine endpoints and refine future studies. The above measures will help to improve data quality as well as

  10. Radon concentration distribution mapping in a small detached house

    International Nuclear Information System (INIS)

    Muellerova, Monika; Moravcsik, Attila; Holy, Karol; Hutka, Miroslav; Hola, Olga

    2013-01-01

    Radon activity concentration was investigated in an older, single storey detached house. The rooms of the house are in contact with the bedrock. The house is fitted with plastic windows and populated mostly during the summer. Integral (Raduet) and continuous (AlphaGUARD) methods were used to measure the radon activity concentration. Average radon and thoron activity concentrations in the house were 150 Bq/m 3 and 40 Bq/m 3 , respectively. The impact of the house occupancy on radon activity concentration was significant only during the summer months when a decrease of radon activity concentration was recorded due to an increased ventilation rate. In the autumn and winter months, the impact of the house occupancy on radon activity concentration was relatively small - up to 20 %. The increases in radon activity concentration after the room had been thoroughly ventilated were analysed in order to estimate the ventilation rate and the rate of radon supply into the house. (orig.)

  11. The contribution of housing renovation to children’s blood lead levels: a cohort study

    Science.gov (United States)

    2013-01-01

    Background Routine renovation of older housing is a risk factor for childhood lead poisoning, but the contribution to children’s blood lead levels is poorly defined for children with lower exposure levels. Methods We examined a prospective cohort of 276 children followed from 6 to 24 months of age. We conducted surveys of renovation activities and residential lead hazards and obtained blood lead level (B-Pb) every six months. We analyzed B-Pb in a repeated measures design using a mixed effects linear model. Results Parent reported interior renovation ranged from 11 to 25% of housing units at the four, 6-month periods. In multivariable analysis, children whose housing underwent interior renovation had a 12% higher mean B-Pb by two years of age compared with children whose housing units were not renovated (p children in non-renovated housing, children whose housing units underwent renovation in the prior month had a 17% higher mean B-Pb at two years of age, whereas children whose housing renovation occurred in the prior 2–6 months had an 8% higher mean B-Pb. We also found an association between higher paint lead loading, measured using an X-ray fluorescence (XRF) based paint lead index, and child B-Pb (p = 0.02); for every 10 mg/cm2 increase in paint lead loading index there was a 7.5% higher mean childhood B-Pb. Conclusions In an analysis of data collected before the recent changes to Environmental Protection Agency’s Lead, Renovation, Repair and Painting Rule, routine interior housing renovation was associated with a modest increase in children’s B-Pb. These results are important for the provision of clinical advice, for housing and public health professionals, and for policymakers. PMID:23981571

  12. Actuator assembly including a single axis of rotation locking member

    Science.gov (United States)

    Quitmeyer, James N.; Benson, Dwayne M.; Geck, Kellan P.

    2009-12-08

    An actuator assembly including an actuator housing assembly and a single axis of rotation locking member fixedly attached to a portion of the actuator housing assembly and an external mounting structure. The single axis of rotation locking member restricting rotational movement of the actuator housing assembly about at least one axis. The single axis of rotation locking member is coupled at a first end to the actuator housing assembly about a Y axis and at a 90.degree. angle to an X and Z axis providing rotation of the actuator housing assembly about the Y axis. The single axis of rotation locking member is coupled at a second end to a mounting structure, and more particularly a mounting pin, about an X axis and at a 90.degree. angle to a Y and Z axis providing rotation of the actuator housing assembly about the X axis. The actuator assembly is thereby restricted from rotation about the Z axis.

  13. Household electricity demand profiles

    DEFF Research Database (Denmark)

    Marszal, Anna Joanna; Heiselberg, Per Kvols; Larsen, Olena Kalyanova

    2016-01-01

    Highlights •A 1-min resolution household electricity load model is presented. •Model adapts a bottom-up approach with single appliance as the main building block. •Load profiles are used to analyse the flexibility potential of household appliances. •Load profiles can be applied in other domains, .......g. building energy simulations. •The demand level of houses with different number of occupants is well captured....

  14. Shear and foundation effects on crack root rotation and mode-mixity in moment- and force-loaded single cantilever beam sandwich specimen

    DEFF Research Database (Denmark)

    Saseendran, Vishnu; Carlsson, Leif A.; Berggreen, Christian

    2017-01-01

    Foundation effects play a crucial role in sandwich fracture specimens with a soft core. Accurate estimation of deformationcharacteristics at the crack front is vital in understanding compliance, energy release rate and mode-mixity infracture test specimens. Beam on elastic foundation analysis...... modulus is proposed that closely agrees with the numerical compliance and energy release rate results forall cases considered. An analytical expression for crack root rotation of the loaded upper face sheet provides consistentresults for both loading configurations. For the force-loaded single cantilever...

  15. Application of a radon model to explain indoor radon levels in a Swedish house

    CERN Document Server

    Font, L; Jönsson, G; Enge, W; Ghose, R

    1999-01-01

    Radon entry from soil into indoor air and its accumulation indoors depends on several parameters, the values of which normally depend on the specific characteristics of the site. The effect of a specific parameter is often difficult to explain from the result of indoor radon measurements only. The adaptation of the RAGENA (RAdon Generation, ENtry and Accumulation indoors) model to a Swedish house to characterise indoor radon levels and the relative importance of the different radon sources and entry mechanisms is presented. The building is a single-zone house with a naturally-ventilated crawl space in one part and a concrete floor in another part, leading to different radon levels in the two parts of the building. The soil under the house is moraine, which is relatively permeable to radon gas. The house is naturally-ventilated. The mean indoor radon concentration values measured with nuclear track detectors in the crawl-space and concrete parts of the house are respectively 75+-30 and 200+-80 Bq m sup - sup 3...

  16. Smart House Interconnected System Architecture

    Directory of Open Access Journals (Sweden)

    ALBU Răzvan-Daniel

    2017-05-01

    Full Text Available In this research work we will present the architecture of an intelligent house system capable to detect accidents cause by floods, gas, and to protect against unauthorized access or burglary. Our system is not just an alarm, it continuously monitors the house and reports over internet its state. Most of the current smart house systems available on the market alarms the user via email or SMS when an unwanted event happens. Thus, the user assumes that the house is not affected if an alarm message is not received. This is not always true, since the monitoring system components can also damage, or the entire system can become unable to send an alarm message even if it detects an unwanted event. This article presents also details about both hardware and software implementation.

  17. Summary of detailed energy audit and building simulation on archetype sustainable house, Woodbridge ON

    Energy Technology Data Exchange (ETDEWEB)

    Fung, A. [Ryerson Polytechnic Univ., Toronto, ON (Canada). Dept. of Mechanical and Industrial Engineering; Dembo, A.; Zhou, J. [Ryerson Polytechnic Univ., Toronto, ON (Canada). Dept. of Architectural Science

    2009-07-01

    This paper described energy and audit and building simulations conducted on an archetype sustainable house located in Woodbridge, Ontario. The house formed part of a project to construct low energy, sustainable house designs for mass production. The 2 houses formed a duplex. House A was designed using current best design practices, while house B was equipped with advanced and innovative technologies not commonly used in residential constructions. Natural Resources Canada's (NRCan) HOT2000 residential building simulation program was used to evaluate the performance of both houses in the duplex. The simulation program demonstrated that house B performed more efficiently than house A. However, neither houses met their designed values. Significantly larger space heating and cooling loads were identified. The program showed that additional weather-stripping around doors, and caulking around windows will help to reduce the amount of draft in the houses. Assessments are also needed to measure heat losses from the common wall in the basement. It was concluded that the energy performance of the house can be optimized by using the appropriate sealing techniques throughout the building envelope. 2 refs., 1 tab.

  18. Working memory load-dependent spatio-temporal activity of single-trial P3 response detected with an adaptive wavelet denoiser.

    Science.gov (United States)

    Zhang, Qiushi; Yang, Xueqian; Yao, Li; Zhao, Xiaojie

    2017-03-27

    Working memory (WM) refers to the holding and manipulation of information during cognitive tasks. Its underlying neural mechanisms have been explored through both functional magnetic resonance imaging (fMRI) and electroencephalography (EEG). Trial-by-trial coupling of simultaneously collected EEG and fMRI signals has become an important and promising approach to study the spatio-temporal dynamics of such cognitive processes. Previous studies have demonstrated a modulation effect of the WM load on both the BOLD response in certain brain areas and the amplitude of P3. However, much remains to be explored regarding the WM load-dependent relationship between the amplitude of ERP components and cortical activities, and the low signal-to-noise ratio (SNR) of the EEG signal still poses a challenge to performing single-trial analyses. In this paper, we investigated the spatio-temporal activities of P3 during an n-back verbal WM task by introducing an adaptive wavelet denoiser into the extraction of single-trial P3 features and using general linear model (GLM) to integrate simultaneously collected EEG and fMRI data. Our results replicated the modulation effect of the WM load on the P3 amplitude. Additionally, the activation of single-trial P3 amplitudes was detected in multiple brain regions, including the insula, the cuneus, the lingual gyrus (LG), and the middle occipital gyrus (MOG). Moreover, we found significant correlations between P3 features and behavioral performance. These findings suggest that the single-trial integration of simultaneous EEG and fMRI signals may provide new insights into classical cognitive functions. Copyright © 2017 IBRO. Published by Elsevier Ltd. All rights reserved.

  19. About vortex-like atomic motion in a loaded single crystal

    Science.gov (United States)

    Dmitriev, A. I.; Nikonov, A. Yu.

    2017-12-01

    The paper presents a molecular dynamics study of internal stress and atomic displacement redistributions in a preliminary loaded solid. The study demonstrates the possibility of self-organized vortices as dynamic defects of typical size 1-5 nm due to atomic motion in the elastic region at the stage of relaxation. The simulation results agree well with experimental data on strain localization in elastic distortion regions which gives rise to nanodipoles of partial disclinations.

  20. New topology of multiple-input single-output PV system for DC load applications

    Directory of Open Access Journals (Sweden)

    Mohsen M. ELhagry

    2016-12-01

    Full Text Available Improving PV system structure and maximizing the output power of a PV system has drawn many researchers attention nowadays. A proposed multi-input single-output PV system is proposed in this paper. The system consists of multiple PV modules; each module feeds a DC–DC converter. The outputs of the converters are tied together to form a DC voltage source. In order to minimize the output ripples of the converters, the control signal of each converter is time shifted from each other by a certain time interval depending on the number of converters used in the topology. In this study a battery is used as the main load, the load current used as the control variable. A fuzzy logic controller designed to modulate the operating point of the system to get the maximum power. The results show that the proposed system has very good response for various operating conditions of the PV system. In addition the output filter is minimized with excellent quality of the DC output voltage.

  1. Application of a radon model to explain indoor radon levels in a Swedish house

    International Nuclear Information System (INIS)

    Font, LL.; Baixeras, C.; Joensson, G.; Enge, W.; Ghose, R.

    1999-01-01

    Radon entry from soil into indoor air and its accumulation indoors depends on several parameters, the values of which normally depend on the specific characteristics of the site. The effect of a specific parameter is often difficult to explain from the result of indoor radon measurements only. The adaptation of the RAGENA (RAdon Generation, ENtry and Accumulation indoors) model to a Swedish house to characterise indoor radon levels and the relative importance of the different radon sources and entry mechanisms is presented. The building is a single-zone house with a naturally-ventilated crawl space in one part and a concrete floor in another part, leading to different radon levels in the two parts of the building. The soil under the house is moraine, which is relatively permeable to radon gas. The house is naturally-ventilated. The mean indoor radon concentration values measured with nuclear track detectors in the crawl-space and concrete parts of the house are respectively 75±30 and 200±80 Bq m -3 . Results of the model adaptation to the house indicate that soil constitutes the most relevant radon source in both parts of the house. The radon concentration values predicted by the model indoors fall into the same range as the experimental results

  2. MORTGAGE FINANCING. Actuarial Soundness of the Federal Housing Administration's Mutual Mortgage Insurance Fund

    National Research Council Canada - National Science Library

    2002-01-01

    ...) of the Department of Housing and Urban Development's (HUD) Federal Housing Administration (FHA). Through the Fund, FHA operates a single-family insurance program that helps millions of Americans buy homes...

  3. Demonstration Platform for near-zero energy buildings - small houses; Demonstrationsplattform foer naeranollenergibyggnader - smaahus

    Energy Technology Data Exchange (ETDEWEB)

    Ruud, Svein; Fahlen, Per; Axell, Monica; Kovacs, Peter; Ylmen, Peter; Staahl, Fredrik

    2011-07-01

    On behalf of the Swedish Energy Agency, SP has investigated and recommended how one could form a platform for demonstration of single family houses as nearly zero energy houses. SP suggests that TMF, the national trade and employers' association of the wood processing and furniture industry in Sweden, should administrate this platform. The reason being that members of TMF produce almost 80% of all single family houses in Sweden. TMF also has the capacity to launch a demonstration platform in a reasonable short time. SP has also compiled a set on technical criteria regarding properties related to energy use that should be met by demonstration projects within the platform. One presumption has been that a house that meets the criteria in the south of Sweden also should meet the criteria in the north of Sweden. The reason being to promote an industrialized and cost effective building process. Another ambition has been not to disfavor smaller single family houses. The main criteria are on very energy efficient building envelopes and very efficient building services systems. The criteria are therefore more detailed than the current Swedish building regulations

  4. U.S. broiler housing ammonia emissions inventory

    Science.gov (United States)

    Gates, R. S.; Casey, K. D.; Wheeler, E. F.; Xin, H.; Pescatore, A. J.

    Using recently published baseline ammonia emissions data for U.S. broiler chicken housing, we present a method of estimating their contribution to an annual ammonia budget that is different from that used by USEPA. Emission rate increases in a linear relationship with flock age from near zero at the start of the flock to a maximum at the end of the flock, 28-65 days later. Market weight of chickens raised for meat varies from "broilers" weighing about 2 kg to "roasters" weighing about 3 kg. Multiple flocks of birds are grown in a single house annually, with variable downtime to prepare the house between flocks. The method takes into account weight and number of chickens marketed. Uncertainty in baseline emissions estimates is used so that inventory estimates are provided with error estimates. The method also incorporates the condition of litter that birds are raised upon and the varying market weight of birds grown. Using 2003 USDA data on broiler production numbers, broiler housing is estimated to contribute 8.8-11.7 kT ammonia for new and built-up litter, respectively, in Kentucky and 240-324 kT ammonia for new and built-up litter, respectively, nationally. Results suggest that a 10% uncertainty in annual emission rate is expected for the market weight categories of broilers, heavy broilers, and roasters. A 27-47% reduction in annual housing emission rate is predicted if new rather than built-up litter were used for every flock. The estimating method can be adapted to other meat bird building emissions and future ammonia emission strategies, with suitable insertion of an age-dependent emission factor or slope into a predictive model equation. The method can be readily applied and is an alternative to that used by USEPA.

  5. Improved mass-measurement accuracy using a PNB Load Cell Scale

    International Nuclear Information System (INIS)

    Suda, S.; Pontius, P.; Schoonover, R.

    1981-08-01

    The PNB Load Cell Scale is a Preloaded, Narrow-Band calibration mass comparator. It consists of (1) a frame and servo-mechanism that maintains a preload tension on the load cell until the load, an unknown mass, is sensed, and (2) a null-balance digital instrument that suppresses the cell response associated with the preload, thereby improving the precision and accuracy of the measurements. Ideally, the objects used to set the preload should be replica mass standards that closely approximate the density and mass of the unknowns. The advantages of the PNB scale are an expanded output signal over the range of interest which increases both the sensitivity and resolution, and minimizes the transient effects associated with loading of load cells. An area of immediate and practical application of this technique to nuclear material safeguards is the weighing of UF 6 cyliners where in-house mass standards are currently available and where the mass values are typically assigned on the basis of comparison weighings. Several prototypical versions of the PNB scale have been assembled at the US National Bureau of Standards. A description of the instrumentation, principles of measurements, and applications are presented in this paper

  6. Optimum residential load management strategy for real time pricing (RTP) demand response programs

    International Nuclear Information System (INIS)

    Lujano-Rojas, Juan M.; Monteiro, Cláudio; Dufo-López, Rodolfo; Bernal-Agustín, José L.

    2012-01-01

    This paper presents an optimal load management strategy for residential consumers that utilizes the communication infrastructure of the future smart grid. The strategy considers predictions of electricity prices, energy demand, renewable power production, and power-purchase of energy of the consumer in determining the optimal relationship between hourly electricity prices and the use of different household appliances and electric vehicles in a typical smart house. The proposed strategy is illustrated using two study cases corresponding to a house located in Zaragoza (Spain) for a typical day in summer. Results show that the proposed model allows users to control their diary energy consumption and adapt their electricity bills to their actual economical situation. - Highlights: ► This work shows an optimal load management strategy for residential consumers. ► It has been considered the communication infrastructure of the future smart grid. ► A study case shows the optimal utilization of some appliances and electric vehicles. ► Results showed that the proposed model allows users to reduce their electricity bill.

  7. Application of Load Carrying Sandwich Elements in Wind Turbine Blades

    DEFF Research Database (Denmark)

    Jensen, Jacob Fisker; Schultz, Jacob Pagh; Berggreen, Carl Christian

    2005-01-01

    The present work investigates the possibilities and drawbacks when applying sandwich as opposed to single skin composites in the flanges of the load carrying spar in a future 180 m wind turbine rotor. FEA is applied to investigate two basic designs with single skin and sandwich flanges respectively...

  8. Affordable housing as a niche product: The case of the Danish “SocialHousing Plus”

    DEFF Research Database (Denmark)

    Jensen, Jesper Ole; Stensgaard, Anne Gro

    Establishing affordable housing is a growing demand in many larger cities there is however a number of challenges related to establishing affordable housing, as well as many different approaches. This paper presents a case-study of an affordable housing concept in the Danish social housing sector......, the “SocialHousing Plus” (“AlmenBolig+”) which is based on lowering production costs as well as operation costs including residential self-management, large-scale production of pre-fab housing units, low-energy solutions and other innovative approaches. The concept was developed in 2007, and has so far...... resulted in the production of more than 1.500 dwellings. The paper will discuss the results of the concept, and the various challenges related to it. Based on the theory of Technological Transition (Geels, 2002) it will discuss the options and limitations of providing affordable housing through developing...

  9. Bottom loaded filter for radioactive liquids

    International Nuclear Information System (INIS)

    Wendland, W.G.

    1983-01-01

    This invention relates to equipment for filtering liquids and more particularly to filter assemblies for use with radioactive by-products of nuclear power plants. The invention provides a compact, bottom-loaded filter assembly that can be quickly and safely loaded and unloaded without the use of complex remote equipment. The assembly is integrally shielded and does not require external shielding. The closure hatch may be automatically aligned to facilitate quick sealing attachment after replacement of the filter cartridge, and the filter cartridge may be automatically positioned within the filter housing during the replacement operation

  10. Simultaneous, single-pulse, synchrotron x-ray imaging and diffraction under gas gun loading

    Energy Technology Data Exchange (ETDEWEB)

    Fan, D.; Luo, S. N., E-mail: sluo@pims.ac.cn [The Peac Institute of Multiscale Sciences, Chengdu, Sichuan 610031 (China); Key Laboratory of Advanced Technologies of Materials, Ministry of Education, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Huang, J. W.; Zeng, X. L.; Li, Y.; E, J. C.; Huang, J. Y. [The Peac Institute of Multiscale Sciences, Chengdu, Sichuan 610031 (China); Sun, T.; Fezzaa, K. [Advanced Photon Source, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Wang, Z. [Physics Division P-25, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

    2016-05-15

    We develop a mini gas gun system for simultaneous, single-pulse, x-ray diffraction and imaging under high strain-rate loading at the beamline 32-ID of the Advanced Photon Source. In order to increase the reciprocal space covered by a small-area detector, a conventional target chamber is split into two chambers: a narrowed measurement chamber and a relief chamber. The gas gun impact is synchronized with synchrotron x-ray pulses and high-speed cameras. Depending on a camera’s capability, multiframe imaging and diffraction can be achieved. The proof-of-principle experiments are performed on single-crystal sapphire. The diffraction spots and images during impact are analyzed to quantify lattice deformation and fracture; fracture is dominated by splitting cracks followed by wing cracks, and diffraction peaks are broadened likely due to mosaic spread. Our results demonstrate the potential of such multiscale measurements for studying high strain-rate phenomena at dynamic extremes.

  11. Single-Family Housing Value Resilience of Walkable Versus Unwalkable Neighborhoods During a Market Downturn: Causal Evidence and Policy Implications.

    Science.gov (United States)

    Xu, Minjie; Yu, Chia-Yuan; Lee, Chanam; Frank, Lawrence D

    2018-01-01

    This study investigated the resilience of single-family housing values in walkable versus unwalkable neighborhoods during the economic downturn from 2008 to 2012 in Dallas, Texas. Using propensity score matching and difference in differences methods, this study established a natural experimental design to compare before-and-after value changes of single-family (SF) homes in walkable neighborhoods with unwalkable neighborhoods during the Great Recession. Two thousand seven hundred ninety-nine SF homes within 18 Tax Increment Financing (TIF) districts were categorized into walkable (Walk Score ≥50) and unwalkable (economic benefit. Increased awareness of the sustained value of walkable communities can be used by lenders who finance and by policy makers who regulate placemaking. Results from this study can be integrated with research that demonstrates health-care cost savings of walkable environments to create an even more comprehensive set of evidence-based interventions to increase their supply.

  12. House dust as possible route of environmental exposure to cadmium and lead in the adult general population

    International Nuclear Information System (INIS)

    Hogervorst, Janneke; Plusquin, Michelle; Vangronsveld, Jaco; Nawrot, Tim; Cuypers, Ann; Van Hecke, Etienne; Roels, Harry A.; Carleer, Robert; Staessen, Jan A.

    2007-01-01

    Contaminated soil particles and food are established routes of exposure. We investigated the relations between biomarkers of exposure to cadmium and lead, and the metal loading rates in house dust in the adult residents of an area with a soil cadmium concentration of >=3mg/kg (n=268) and a reference area (n=205). We determined the metal concentrations in house dust allowed to settle for 3 months in Petri dishes placed in the participants' bedrooms. The continuously distributed vegetable index was the first principal component derived from the metal concentrations in six different vegetables. The biomarkers of exposure (blood cadmium 9.2 vs. 6.2nmol/L; 24-h urinary cadmium 10.5 vs. 7.0nmol; blood lead 0.31 vs. 0.24μmol/L), the loading rates of cadmium and lead in house dust (0.29 vs. 0.12 and 7.52 vs. 3.62ng/cm 2 /92 days), and the vegetable indexes (0.31 vs. -0.44 and 0.13 vs. -0.29 standardized units) were significantly higher in the contaminated area. A two-fold increase in the metal loading rate in house dust was associated with increases (P<0.001) in blood cadmium (+2.3%), 24-h urinary cadmium (+3.0%), and blood lead (+2.0%), independent of the vegetable index and other covariates. The estimated effect sizes on the biomarkers of internal exposure were three times greater for house dust than vegetables. In conclusion, in the adult population, house dust is potentially an important route of exposure to heavy metals in areas with contaminated soils, and should be incorporated in the assessment of health risks

  13. Preparation and functional studies of hydroxyethyl chitosan nanoparticles loaded with anti-human death receptor 5 single-chain antibody

    Directory of Open Access Journals (Sweden)

    Yang J

    2014-05-01

    Full Text Available Jingjing Yang,1,3,* Xiaoping Huang,1,3,* Fanghong Luo,1 Xiaofeng Cheng,3 Lianna Cheng,3 Bin Liu,4 Lihong Chen,2 Ruyi Hu,1,3 Chunyan Shi,1,3 Guohong Zhuang,1,3 Ping Yin2 1Anti-Cancer Research Center, Medical College, Xiamen University, Fujian, People's Republic of China, 2The Department of Pathology, Zhongshan Hospital, Xiamen University, Xiamen, People's Republic of China, 3Organ transplantation institution, Xiamen University, Xiamen, People's Republic of China, 4Jilin Vocational College of Industry and Technology, Jilin, People's Republic of China  *These authors contributed equally to this work Objective: To prepare hydroxyethyl chitosan nanoparticles loaded with anti-human death receptor 5 single-chain antibody, and study their characteristics, functions, and mechanisms of action. Materials and methods: The anti-human death receptor 5 single-chain antibody was constructed and expressed. Protein-loaded hydroxyethyl chitosan nanoparticles were prepared, and their size, morphology, particle-size distribution and surface zeta potential were measured by scanning electron microscopy and laser particle-size analysis. Mouse H22 hepatocellular carcinoma cells were cultured, and growth inhibition was examined using the CellTiter-Blue cell-viability assay. Flow cytometry and Hoechst 33342 were employed to measure cell apoptosis. Kunming mice with H22 tumor models were treated with protein-loaded hydroxyethyl chitosan nanoparticles, and their body weight and tumor size were measured, while hematoxylin and eosin staining was used to detect antitumor effects in vivo and side effects from tumors. Results: The protein-loaded hydroxyethyl chitosan nanoparticles had good stability; the zeta potential was -24.2±0.205, and the dispersion index was 0.203. The inhibition of the protein-loaded hydroxyethyl chitosan nanoparticles on H22 growth was both time- and dose-dependent. Increased expressions of active caspase 8, active caspase 3, and BAX were detected

  14. Simplified analysis of laterally loaded pile groups

    Directory of Open Access Journals (Sweden)

    F.M. Abdrabbo

    2012-06-01

    Full Text Available The response of laterally loaded pile groups is a complicated soil–structure interaction problem. Although fairly reliable methods are developed to predicate the lateral behavior of single piles, the lateral response of pile groups has attracted less attention due to the required high cost and complication implication. This study presents a simplified method to analyze laterally loaded pile groups. The proposed method implements p-multiplier factors in combination with the horizontal modulus of subgrade reaction. Shadowing effects in closely spaced piles in a group were taken into consideration. It is proven that laterally loaded piles embedded in sand can be analyzed within the working load range assuming a linear relationship between lateral load and lateral displacement. The proposed method estimates the distribution of lateral loads among piles in a pile group and predicts the safe design lateral load of a pile group. The benefit of the proposed method is in its simplicity for the preliminary design stage with a little computational effort.

  15. Innova House - Ottawa`s advanced house

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-01-31

    A pilot program was developed to provide the housing industry with a means to field test innovative technologies, products and building systems, and to evaluate their overall performance. Under Canada`s Advanced House Program, ten demonstration houses were designed, built and monitored. Ottawa`s Innova House, was one of the ten houses built for this program. The innovative energy saving features of the house included (1) air distribution with small diameter ducts and an electronically commutated motor, a 2.6 kW grid-connected photovoltaic system, (3) an energy recovery ventilator (ERV) with free-cooling mode, (4) a 94 per cent efficient integrated gas heating and hot water system, (5) airtight drywall construction, (6) CFC-free exterior insulation, (7) a natural-gas-engine heat pump for air conditioning, (8) a prototype sealed combustion gas range and clothes dryer, and (9) a manifold plumbing system to conserve water. It was designed to consume one half of the energy consumed in an R-2000 home and one third of the energy of a conventional house. Several of the mechanical elements did not perform at expected levels, (lower than expected efficiencies from the heating and cooling systems and a malfunctioning ERV), nevertheless, overall performance of the house was still very close to the targets. The construction and operation of the house was described. tabs., figs.

  16. Subharmonic beam-loading in electron linear accelerators

    International Nuclear Information System (INIS)

    Gallagher, W.J.

    1983-01-01

    The intention of operating an electron linear accelerator subharmonically beam loaded for free electron laser application requires justification of the beam-loaded energy gain equation. The mode of operation typically planned is 5 to 10 nanocoulombs single RF cycle pulses at 25 to 50 nanosecond intervals. This inquiry investigates the details of this sort of beam loading and discusses the performance achievable. Several other investigations of single bunch beam loading have been undertaken, notably at SLAC, where it has been found experimentally that the beam-loading varies directly as the bunch charge and independently of its energy; that investigation also included radiation effects of the wake field and losses owing to parasitic effects of higher order modes. In the case of beam loading where there are multiple pulses transiting at the same time, and spaced far enough apart that significant RF power is introduced between pulses, the energy gain may be calculated by dividing the waveguide into a number of segments, each equal in length to the integral of the interpulse time and the local group velocity. Equations which reveal that the net energy gain in the steady state is the sum of the energy gains in these segments, which compute the initial field intensity, and which calculate the energy gain in the subharmonic case on the basis of the equivalent beam current are presented

  17. Decentralized method for load sharing and power management in a hybrid single/three-phase islanded microgrid consisting of hybrid source PV/battery units

    DEFF Research Database (Denmark)

    Karimi, Yaser; Guerrero, Josep M.; Oraee, Hashem

    2016-01-01

    This paper proposes a new decentralized power management and load sharing method for a photovoltaic based, hybrid single/three-phase islanded microgrid consisting of various PV units, battery units and hybrid PV/battery units. The proposed method takes into account the available PV power...... and battery conditions of the units to share the load among them and power flow among different phases is performed automatically through three-phase units. Modified active power-frequency droop functions are used according to operating states of each unit and the frequency level is used as trigger...... for switching between the states. Efficacy of the proposed method in different load, PV generation and battery conditions is validated experimentally in a microgrid lab prototype consisted of one three-phase unit and two single-phase units....

  18. 7 CFR 1955.111 - Sale of real estate for RH purposes (housing).

    Science.gov (United States)

    2010-01-01

    ... HOUSING SERVICE, RURAL BUSINESS-COOPERATIVE SERVICE, RURAL UTILITIES SERVICE, AND FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE (CONTINUED) PROGRAM REGULATIONS (CONTINUED) PROPERTY MANAGEMENT Disposal of... Housing Act of 1949, as amended, (RH property). Single family units (generally which secured loans made...

  19. Polish Housing Policy in Com parison with the Housing Policy in the UE – Selected Issues

    Directory of Open Access Journals (Sweden)

    Anna Szelągowska

    2011-07-01

    Full Text Available The purpose of this article is to present the main principles of Polish housing policy and to compare it with the housing policy in the European Union. Poland, as an UE member, did not hammer out successful solutions which could facilitate the process of building new low-rental dwellings. The authors aim is to find the answer to research question: is it worth concentrating on fulfilling housing needs of low-income households in Poland and if yes, why? In order to do this the following hypothesis is put forward: on account of long-standing neglect connected with the Polish social housing finance there is an urgent need of housing reform oriented to the low-income housing growth.

  20. Testimony presented to the House Science and Technology Committee, 18 June 1981, Washington, DC

    International Nuclear Information System (INIS)

    Richmond, C.R.

    1981-10-01

    This report is the text of invited testimony given by the author before the House Science and Technology Committee. This Congressional hearing on Societal Risks of Energy Systems reflects the growing interest on the part of Congress, the public, the scientific community, and other groups on this extremely important topic of Risk Analysis. This presentation will contain information on the emergence of an interdisciplinary professional field of risk analysis, including the recently formed Society for Risk Analysis. I will also discuss in some detail various risk analysis programs now in progress at the Oak Ridge National Laboratory and other research institutions. Also included will be some general philosophy concerning risks from energy-producing systems and my perspective on the needs for further developments in the field of risk analysis

  1. Projecting housing starts and softwood lumber consumption in the United States

    Science.gov (United States)

    Jeffrey P. Prestemon; David N. Wear; Karen L. Abt; Robert C. Abt

    2018-01-01

    New residential construction is a primary user of wood products in the United States; therefore, wood products projections require understanding the determinants of housing starts. We model quarterly US total, single-family, and multifamily housing starts with several model specifications, using data from 1979 to 2008, and evaluate their...

  2. Housing markets and housing policies in India

    OpenAIRE

    Tiwari, Piyush; Rao, Jyoti

    2016-01-01

    Issues of housing in India are synonymous with ignorance of housing in active government involvement at the policy and program formulation levels. They are also due to the problems that unplanned urbanization, income disparity, poverty, illiteracy, and unemployment brought. These issues extenuated the housing problem, causing a housing shortage of 51 million in 2011. Though India has a long history of establishing policies, programs, and institutions to cater to housing, without allocating ad...

  3. Single-crystal charge transfer interfaces for efficient photonic devices (Conference Presentation)

    Science.gov (United States)

    Alves, Helena; Pinto, Rui M.; Maçôas, Ermelinda M. S.; Baleizão, Carlos; Santos, Isabel C.

    2016-09-01

    Organic semiconductors have unique optical, mechanical and electronic properties that can be combined with customized chemical functionality. In the crystalline form, determinant features for electronic applications such as molecular purity, the charge mobility or the exciton diffusion length, reveal a superior performance when compared with materials in a more disordered form. Combining crystals of two different conjugated materials as even enable a new 2D electronic system. However, the use of organic single crystals in devices is still limited to a few applications, such as field-effect transistors. In 2013, we presented the first system composed of single-crystal charge transfer interfaces presenting photoconductivity behaviour. The system composed of rubrene and TCNQ has a responsivity reaching 1 A/W, corresponding to an external quantum efficiency of nearly 100%. A similar approach, with a hybrid structure of a PCBM film and rubrene single crystal also presents high responsivity and the possibility to extract excitons generated in acceptor materials. This strategy led to an extended action towards the near IR. By adequate material design and structural organisation of perylediimides, we demonstrate that is possible to improve exciton diffusion efficiency. More recently, we have successfully used the concept of charge transfer interfaces in phototransistors. These results open the possibility of using organic single-crystal interfaces in photonic applications.

  4. Description of case houses. Building integrated energy supply; Beskrivelse af casehuse. Bygningsintegreret energiforsyning

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, Rasmus L.; Noergaard, J.; Daniels, O.; Justesen, R.O.

    2011-08-15

    In the future, buildings will not only act as consumers of energy but as producers as well. For these ''prosumers'', energy production by use of solar panels, photovoltaics and heat pumps etc will be essential. The objective of this project was to find the most optimal combinations of building insulation and use of renewable energy sources in existing buildings in terms of economics and climate impacts. Five houses were analyzed based on different personal load, consumption profiles, solar orientation and proposed building envelope improvements and use of combinations of renewable energy systems. The present report describes typical construction details of the building envelope (windows, floor, outside wall and roof/ceiling) for houses built in the years 1961-1972, 1973-1978 and 1979-1998. Furthermore the report describes the necessary improvements for the buildings' U-value to be the minimum value as stated in the Danish building code of 2010, and to be the values for buildings at the level of low-energy class 2015. Cost estimation for optimizing the houses to an optimum insulation level has been made. (ln)

  5. Flair Homes Project report no. 5. Airtightness performance of twenty detached houses over a two-year period

    Energy Technology Data Exchange (ETDEWEB)

    Proskiw, G.; Beckman, J.

    1989-01-01

    Airtightness tests were performed on 20 new houses over a 2-year period in Winnipeg. The houses were constructed with a variety of air/vapor barrier systems and 3 different types of main walls. Polyethylene was used as the air/vapor barrier in 6 of the houses while the remaining 14 used the airtight drywall approach (ADA). The houses had similar floor plans and were constructed by the same builder. Both the polyethylene and ADA systems were found to be capable of meeting the airtightness requirements of the R-2000 standard with the tightest structures being double wall houses. No significant or permanent change in airtightness was observed for any of the houses over the monitoring period. Application of stucco as an exterior finish was found to improve airtightness of the ADA houses, but not of the double wall houses with polyethylene vapor barriers. Consistent sources of air leakage in the ADA houses were found to be the electrical outlets on exterior walls. Window leakage was also noted in many houses and the frequency of this leakage increased over the monitoring period. A significant leakage source was found to be an integrated mechanical system, which ducted in large volumes of outdoor air. It was also concluded there is a need to re-examine the design pressure requirements for residential air barrier systems. Specifically, this should investigate how transient wind-induced pressure loads are resisted by air barrier systems and whether some portion of the load is taken by other envelope components. An air leakage detection system was proposed consisting of a simple non-instrumented blower, which would be suitable for use by builders to aid in the construction of low leakage houses. 17 refs., 10 figs., 8 tabs.

  6. Impact of Urban Heat Island under the Hanoi Master Plan 2030 on Cooling Loads in Residential Buildings

    Directory of Open Access Journals (Sweden)

    Tran Hoang Hai Nam

    2015-01-01

    Full Text Available This study aims to evaluate the influence of urban heat island (UHI under the Hanoi Master Plan 2030 on the energy consumption for space cooling in residential buildings. The weather conditions under the current and future status (master plan condition simulated in the previous study (Trihamdani et al., 2014 were used and cooling loads in all the residential buildings in Hanoi over the hottest month were estimated under the simulated current and future conditions by using the building simulation program, TRNSYS (v17. Three most typical housing types in the city were selected for the simulation. The cooling loads of respective housing types were obtained in each of the districts in Hanoi. The results show that the total cooling loads over June 2010 is approximately 683 Terajoule (TJ under the current status, but it is predicted to increase to 903 TJ under the master plan condition. The increment is largely due to the increase in number of households (203 TJ or 92%, but partially due to the increase in urban temperature, i.e. UHI effect (17 TJ or 8%. The increments in new built-up areas were found to be larger than those in existing built-up areas. The cooling load in apartment is approximately half of that in detached house, which is approximately half of that in row house. Moreover, it was seen that although sensible cooling loads increased with the increase in outdoor temperature, the latent cooling loads decreased due to the decrease in absolute humidity and the increase in air temperature.

  7. Demand and supply of labour in the housing sector

    NARCIS (Netherlands)

    Dol, C.P.; Doling, J.; Elsinga, M.; Horsewood, N.; Meijer, F.M.; Visscher, H.J.

    2015-01-01

    The housing sector is large and significant in all aspects of human life, making the task of the policy-maker especially complex. Homes constitute the largest single land use in the ‘built environment’, they are generally the largest single item of expenditure in household budgets and the largest

  8. Performance of skylight illuminance inside a dome shaped adobe house under composite climate at New Delhi (India: A typical zero energy passive house

    Directory of Open Access Journals (Sweden)

    Arvind Chel

    2014-06-01

    Full Text Available This paper presents annual experimental performance of pyramid shaped skylight for daylighting of a dome shaped adobe house located at solar energy park in New Delhi (India. This approach of single story dome shaped building with skylight is more useful for rural and semi-urban sectors for both office and residential buildings reducing artificial lighting energy consumption. The hourly measured data of inside and outside illuminance for three different working surface levels inside the existing rooms are presented for each month of the year. The embodied energy payback time of the skylight is also determined on the basis of lighting energy saving potential.

  9. 25-Hydroxycholecalciferol response to single oral cholecalciferol loading in the normal weight, overweight, and obese.

    Science.gov (United States)

    Camozzi, V; Frigo, A C; Zaninotto, M; Sanguin, F; Plebani, M; Boscaro, M; Schiavon, L; Luisetto, G

    2016-08-01

    After a single cholecalciferol load, peak serum 25-hydroxycholecalciferol (25OHD) is lower in individuals with a higher body mass index (BMI), probably due to it being distributed in a greater volume. Its subsequent disappearance from the serum is slower the higher the individual's BMI, probably due to the combination of a larger body volume and a slower release into the circulation of vitamin D stored in adipose tissue. The aim of the study is to examine 25-hydroxycholecalciferol (25OHD) response to a single oral load of cholecalciferol in the normal weight, overweight, and obese. We considered 55 healthy women aged from 25 to 67 years (mean ± SD, 50.8 ± 9.5) with a BMI ranging from 18.7 to 42 kg/m(2) (mean ± SD, 27.1 ± 6.0). The sample was divided into three groups by BMI: 20 were normal weight (BMI ≤ 25 kg/m(2)), 21 overweight (25.1 ≤ BMI ≤ 29.9 kg/ m(2)), and 14 obese (BMI ≥ 30 kg/m(2)). Each subject was given 300,000 IU of cholecalciferol orally during lunch. A fasting blood test was obtained before cholecalciferol loading and then 7, 30, and 90 days afterwards to measure serum 25OHD, 1,25 dihydroxyvitamin D [1,25 (OH)2D], parathyroid hormone (PTH), calcium (Ca), and phosphorus (P). Participants' absolute fat mass was measured using dual energy X-ray absorptiometry (DEXA). The fat mass of the normal weight subjects was significantly lower than that of the overweight, which in turn was lower than that of the obese participants. Serum 25OHD levels increased significantly in all groups, peaking 1 week after the cholecalciferol load. Peak serum 25OHD levels were lower the higher the individuals' BMI. After peaking, the 25OHD levels gradually decreased, following a significantly different trend in the three groups. The slope was similar for the overweight and obese, declining significantly more slowly than in the normal weight group. In the sample as a whole, there was a weakly significant negative correlation

  10. 24 CFR 982.608 - Congregate housing: Voucher housing assistance payment.

    Science.gov (United States)

    2010-04-01

    ... Housing Types Congregate Housing § 982.608 Congregate housing: Voucher housing assistance payment. (a... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Congregate housing: Voucher housing assistance payment. 982.608 Section 982.608 Housing and Urban Development Regulations Relating to Housing and...

  11. Striving for meaning—Life in supported housing for people with psychiatric disabilities

    Directory of Open Access Journals (Sweden)

    Rosita Brolin

    2016-05-01

    Full Text Available The aim of this study was to develop a grounded theory about people with psychiatric disabilities, living in supported housing. Interviews as well as observations during the interviews were analyzed together with secondary analyses of quantitative and qualitative material from previous studies. Being deprived of self-determination emerged as the main concern for residents in supported housing and striving for meaning emerged as the pattern of behavior through which this group resolves their main concern. Striving for meaning involves living in the present, striving for self-determination, strengthening self-esteem, emotional processing and resting from the present. The strategies facilitate each other and are used singly, together simultaneously, or alternately. If they are successful, a meaning in the present is perceived. If all the strategies fail repeatedly, escaping from the present is used in order to deal with being deprived of self-determination. The implications of the findings suggest prioritizing a reduction of the institutional nature of the social and physical environment, and to support the residents’ self-determination.

  12. Striving for meaning-Life in supported housing for people with psychiatric disabilities.

    Science.gov (United States)

    Brolin, Rosita; Brunt, David; Rask, Mikael; Syrén, Susanne; Sandgren, Anna

    2016-01-01

    The aim of this study was to develop a grounded theory about people with psychiatric disabilities, living in supported housing. Interviews as well as observations during the interviews were analyzed together with secondary analyses of quantitative and qualitative material from previous studies. Being deprived of self-determination emerged as the main concern for residents in supported housing and striving for meaning emerged as the pattern of behavior through which this group resolves their main concern. Striving for meaning involves living in the present, striving for self-determination, strengthening self-esteem, emotional processing and resting from the present. The strategies facilitate each other and are used singly, together simultaneously, or alternately. If they are successful, a meaning in the present is perceived. If all the strategies fail repeatedly, escaping from the present is used in order to deal with being deprived of self-determination. The implications of the findings suggest prioritizing a reduction of the institutional nature of the social and physical environment, and to support the residents' self-determination.

  13. The health status and well-being of low-resource, housing-unstable, single-parent families living in violent neighbourhoods in Philadelphia, Pennsylvania.

    Science.gov (United States)

    Jacoby, Sara F; Tach, Laura; Guerra, Terry; Wiebe, Douglas J; Richmond, Therese S

    2017-03-01

    The health and well-being of single-parent families living in violent neighbourhoods in US cities who participate in housing programmes is not well described. This two-phase, mixed-methods study explores the health status of families who were participants in a housing-plus programme in Philadelphia, Pennsylvania between 2011 and 2013 and the relationship between the characteristics of the neighbourhoods in which they lived and their perceptions of well-being and safety. In phase 1, data collected with standardised health status instruments were analysed using descriptive statistics and independent sample t-tests to describe the health of single parents and one randomly selected child from each parent's household in comparison to population norms. In a subset of survey respondents, focus groups were conducted to generate an in-depth understanding of the daily lives and stressors of these families. Focus group data were analysed using content analysis to identify key descriptive themes. In phase 2, daily activity path mapping, surveys and interviews of parent-child dyads were collected to assess how these families perceive their health, neighbourhood and the influence of neighbourhood characteristics on the families' day-to-day experience. Narratives and activity maps were combined with crime data from the Philadelphia Police Department to analyse the relationship between crime and perceptions of fear and safety. Phase 1 data demonstrated that parent participants met or exceeded the national average for self-reported physical health but fell below the national average across all mental health domains. Over 40% reported moderate to severe symptoms of depression. Parents described high levels of stress resulting from competing priorities, financial instability, and concern for their children's well-being and safety. Analysis of phase 2 data demonstrated that neighbourhood characteristics exert influence over parents' perceptions of their environment and how they permit

  14. Housing Welfare Policies in Scandinavia

    DEFF Research Database (Denmark)

    Jensen, Lotte

    2013-01-01

    It is commonplace to refer to the Nordic countries of Sweden, Norway, Denmark, Finland and Iceland as a distinctive and homogenous welfare regime. As far as social housing is concerned, however, the institutional heritage of the respective countries significantly frames the ways in which social...... housing is understood, regulated and subsidized, and, in turn, how housing regimes respond to the general challenges to the national welfare states. The paper presents a historical institutionalist approach to understanding the diversity of regime responses in the modern era characterized by increasing...... marketization, welfare criticism and internationalization. The aim is to provide outside readers a theoretically guided empirical insight into Scandinavian social housing policy. The paper first lines up the core of the inbuilt argument of historical institutionalism in housing policy. Secondly, it briefly...

  15. Unitary Housing Regimes in Transition

    DEFF Research Database (Denmark)

    Bengtsson, Bo; Jensen, Lotte

    2013-01-01

    Path dependence is strong in housing institutions and policy. In both Denmark and Sweden, today’s universal and ‘unitary’ (Kemeny) housing regimes can be traced back to institutions that were introduced fifty years back in history or more. Recently, universal and unitary housing systems...... in Scandinavia, and elsewhere, are under challenge from strong political and economic forces. These challenges can be summarized as economic cutbacks, privatization and Europeanization. Although both the Danish and the Swedish housing system are universal and unitary in character, they differ considerably...... in institutional detail. Both systems have corporatist features, however in Denmark public housing is based on local tenant democracy and control, and in Sweden on companies owned and controlled by the municipalities, combined with a centralized system of rent negotiations. In the paper the present challenges...

  16. Models for Experimental High Density Housing

    Science.gov (United States)

    Bradecki, Tomasz; Swoboda, Julia; Nowak, Katarzyna; Dziechciarz, Klaudia

    2017-10-01

    The article presents the effects of research on models of high density housing. The authors present urban projects for experimental high density housing estates. The design was based on research performed on 38 examples of similar housing in Poland that have been built after 2003. Some of the case studies show extreme density and that inspired the researchers to test individual virtual solutions that would answer the question: How far can we push the limits? The experimental housing projects show strengths and weaknesses of design driven only by such indexes as FAR (floor attenuation ratio - housing density) and DPH (dwellings per hectare). Although such projects are implemented, the authors believe that there are reasons for limits since high index values may be in contradiction to the optimum character of housing environment. Virtual models on virtual plots presented by the authors were oriented toward maximising the DPH index and DAI (dwellings area index) which is very often the main driver for developers. The authors also raise the question of sustainability of such solutions. The research was carried out in the URBAN model research group (Gliwice, Poland) that consists of academic researchers and architecture students. The models reflect architectural and urban regulations that are valid in Poland. Conclusions might be helpful for urban planners, urban designers, developers, architects and architecture students.

  17. Combined Loadings and Cross-Dimensional Loadings Timeliness of Presentation of Financial Statements of Local Government

    Science.gov (United States)

    Muda, I.; Dharsuky, A.; Siregar, H. S.; Sadalia, I.

    2017-03-01

    This study examines the pattern of readiness dimensional accuracy of financial statements of local government in North Sumatra with a routine pattern of two (2) months after the fiscal year ends and patterns of at least 3 (three) months after the fiscal year ends. This type of research is explanatory survey with quantitative methods. The population and the sample used is of local government officials serving local government financial reports. Combined Analysis And Cross-Loadings Loadings are used with statistical tools WarpPLS. The results showed that there was a pattern that varies above dimensional accuracy of the financial statements of local government in North Sumatra.

  18. Housing and Health: The relationship between housing conditions ...

    African Journals Online (AJOL)

    okanlawon

    2011-10-22

    Oct 22, 2011 ... Housing and Health: The relationship between housing ... The authors in chapter one, deal extensively with historical context of housing and health chronologically ... Housing and Health: Time Again for Public Health Action.

  19. The Financial Crisis and Diverging House Prices: Evidence from the Copenhagen Metropolitan Area: 2017-084/VIII

    DEFF Research Database (Denmark)

    Mulalic, Ismir; Rasmussen, Holger; Rouwendal, Jan

    This paper investigates the development of house prices in Copenhagen in the period 1994-2013, while paying special attention to the heterogeneous impact of the boom and bust periods along the dimensions of housing type (single vs multifamily housing), geography and quality. To allow for price de...... the high quality segments of the housing market....

  20. Refining Housing, Husbandry and Care for Animals Used in Studies Involving Biotelemetry

    Directory of Open Access Journals (Sweden)

    Penny Hawkins

    2014-06-01

    Full Text Available Biotelemetry can contribute towards reducing animal numbers and suffering in disciplines including physiology, pharmacology and behavioural research. However, the technique can also cause harm to animals, making biotelemetry a ‘refinement that needs refining’. Current welfare issues relating to the housing and husbandry of animals used in biotelemetry studies are single vs. group housing, provision of environmental enrichment, long term laboratory housing and use of telemetered data to help assess welfare. Animals may be singly housed because more than one device transmits on the same wavelength; due to concerns regarding damage to surgical sites; because they are wearing exteriorised jackets; or if monitoring systems can only record from individually housed animals. Much of this can be overcome by thoughtful experimental design and surgery refinements. Similarly, if biotelemetry studies preclude certain enrichment items, husbandry refinement protocols can be adapted to permit some environmental stimulation. Nevertheless, long-term laboratory housing raises welfare concerns and maximum durations should be defined. Telemetered data can be used to help assess welfare, helping to determine endpoints and refine future studies. The above measures will help to improve data quality as well as welfare, because experimental confounds due to physiological and psychological stress will be minimised.

  1. Evaluation of the Energy and Comfort Performance of a Plus-Energy House under Scandinavian Summer Conditions

    DEFF Research Database (Denmark)

    Pean, Thibault Quentin; Gennari, Luca; Kazanci, Ongun Berk

    2016-01-01

    The thermal indoor environment and the energy performance of a plus-energy house are evaluated in the present study. The study case is EMBRACE, a two-storey dwelling of 59 m2 designed to host a single family. The building includes a semi-outdoor space covered by a glazed envelope, where the therm...

  2. Release of volatile and semi-volatile toxicants during house fires.

    Science.gov (United States)

    Hewitt, Fiona; Christou, Antonis; Dickens, Kathryn; Walker, Richard; Stec, Anna A

    2017-04-01

    Qualitative results are presented from analysis of volatile and semi-volatile organic compounds (VOCs/SVOCs) obtained through sampling of gaseous effluent and condensed particulates during a series of experimental house fires conducted in a real house. Particular emphasis is given to the 16 polycyclic aromatic hydrocarbons (PAHs) listed by the Environmental Protection Agency due to their potentially carcinogenic effects. The initial fuel packages were either cooking oil or a single sofa; these were burned both alone, and in furnished surroundings. Experiments were performed at different ventilation conditions. Qualitative Gas Chromatography-Mass Spectrometry (GC-MS) analysis found VOC/SVOC releases in the developing stages of the fires, and benzo(a)pyrene - the most carcinogenic PAH - was found in at least one sampling interval in the majority of fires. A number of phosphorus fire retardants were detected, in both the gaseous effluent and particulates, from fires where the initial fuel source was a sofa. Their release during the fire is significant as they pose toxicological concerns separate from those presented by the PAHs. Copyright © 2016. Published by Elsevier Ltd.

  3. Impacts of the Weatherization Assistance Program in fuel-oil heated houses

    Energy Technology Data Exchange (ETDEWEB)

    Levins, W.P.; Ternes, M.P.

    1994-10-01

    In 1990, the US Department of Energy (DOE) initiated a national evaluation of its lowincome Weatherization Assistance Program. This report, which is one of five parts of that evaluation, evaluates the energy savings and cost-effectiveness of the Program as it had been applied to single-family houses heated primarily by fuel-oil. The study was based upon a representative sample (41 local weatherization agencies, 222 weatherized and 115 control houses) from the nine northeastern states during 1991 and 1992 program years. Dwelling-specific and agency-level data on measures installed, costs, and service delivery procedures were collected from the sampled agencies. Space-heating fuel-oil consumption, indoor temperature, and outdoor temperature were monitored at each house. Dwelling characteristics, air-leakage measurements, space-heating system steady-state efficiency measurements, safety inspections, and occupant questionnaires were also collected or performed at each monitored house. We estimate that the Program weatherized a total of 23,400 single-family fuel-oil heated houses in the nine northeastern states during program years 1991 and 1992. Annual fuel-oil savings were calculated using regression techniques to normalize the savings to standard weather conditions. For the northeast region, annual net fuel-oil savings averaged 160 gallons per house, or 17.7% of pre-weatherization consumption. Although indoor temperatures changed in individual houses following weatherization, there was no average change and no significant difference as compared to the control houses; thus, there was no overall indoor temperature takeback effect influencing fuel-oil savings. The weatherization work was performed cost effectively in these houses from the Program perspective, which included both installation costs and overhead and management costs but did not include non-energy benefits (such as employment and environmental).

  4. Relationships Between Results Of An Internal And External Match Load Determining Method In Male, Singles Badminton Players.

    Science.gov (United States)

    Abdullahi, Yahaya; Coetzee, Ben; Van den Berg, Linda

    2017-07-03

    The study purpose was to determine relationships between results of internal and external match load determining methods. Twenty-one players, who participated in selected badminton championships during the 2014/2015 season served as subjects. The heart rate (HR) values and GPS data of each player were obtained via a fix Polar HR Transmitter Belt and MinimaxX GPS device. Moderate significant Spearman's rank correlations were found between HR and absolute duration (r = 0.43 at a low intensity (LI) and 0.44 at a high intensity (HI)), distance covered (r = 0.42 at a HI) and player load (PL) (r = 0.44 at a HI). Results also revealed an opposite trend for external and internal measures of load as the average relative HR value was found to be the highest for the HI zone (54.1%) compared to the relative measures of external load where average values (1.29-9.89%) were the lowest for the HI zone. In conclusion, our findings show that results of an internal and external badminton match load determining method are more related to each other in the HI zone than other zones and that the strength of relationships depend on the duration of activities that are performed in especially LI and HI zones. Overall, trivial to moderate relationships between results of an internal and external match load determining method in male, singles badminton players reaffirm the conclusions of others that these constructs measure distinctly different demands and should therefore be measured concurrently to fully understand the true requirements of badminton match play.

  5. Passive House at the crossroads: The past and the present of a voluntary standard that managed to bridge the energy efficiency gap

    International Nuclear Information System (INIS)

    Müller, Liana; Berker, Thomas

    2013-01-01

    Improving energy efficiency in dwellings is generally seen as the low-hanging fruit of climate change mitigation. In particular decreased heat loss through better insulation is suggested as one of the most cost-effective means to achieve the ambitious national and international goals of climate gas reduction. However, the literature shows that a profitable technological solution is not sufficient to reach the energy goals. Aspects such as a lack of information, unobserved costs, and heterogeneity among users can compromise the success of technical innovation. Still, there are successful concepts that drive the technological development in the construction sector. The Passive House is an example for such innovations that manage to bridge the energy efficiency gap. This paper addresses the Passive House concept and standard as a success story of technological innovation. With Bruno Latour's Science in Action (1987) as a starting point, we describe the conditions under which the standard was created, the role of the network built around the Passive House Institute, and the consequences of exporting the standard. We identify success factors that have supported the diffusion of the Passive House standard and concept and discuss its possible development in the current situation which is characterized by its wide-spread adoption. - Highlights: • We present the Passive House (PH) as example of technological innovation. • The developers of PH managed to overcome the barriers to energy efficiency. • Successful innovation is more than good technology. • The heterogeneity of adopters of PH is growing. • The future of PH: the tension between rigid control and flexible adaptability

  6. ENERGY EFFICIENT RENOVATION OF SOCIAL HOUSING

    DEFF Research Database (Denmark)

    Blyt, Henrik; Christiansen, Michael; Bech-Nielsen, Grith

    -creating way. The project meets the challenges above by contributing with two findings: First we present methods on how to carry out value generating interdisciplinary collaboration between the housing sector parties, such as residents, housing administration, politicians, advisors, producers and contractors...... contributes to the strengthening of knowledge sharing within the housing sector, and the creation of a framework for long term investments and jobs....

  7. House Prices, Geographical Mobility, and Unemployment

    DEFF Research Database (Denmark)

    Ingholt, Marcus Mølbak

    2017-01-01

    Geographical mobility correlates positively with house prices and negatively with unemployment over the U.S. business cycle. I present a DSGE model in which declining house prices and tight credit conditions impede the mobility of indebted workers. This reduces the workers’ cross-area competition...... for jobs, causing wages and unemployment to rise. A Bayesian estimation shows that this channel more than quadruples the response of unemployment to adverse housing market shocks. The estimation also shows that adverse housing market shocks caused the decline in mobility during the Great Recession. Absent...

  8. High-Frequency Axial Fatigue Test Procedures for Spectrum Loading

    Science.gov (United States)

    2016-07-20

    cycle runout limit. PURPOSE 2. To develop the capability to perform High-Frequency (H-F) Spectrum Fatigue tests, an in- house Basic and...response of the test specimen to the command input signal for load cycling . These cycle -by- cycle errors accumulate over the life of the test specimen...fatigue life model. It is expected that the cycle -by- cycle P-V error may vary substantially depending on the load spectrum content, the compensation

  9. Single Additive Enables 3D Printing of Highly Loaded Iron Oxide Suspensions.

    Science.gov (United States)

    Hodaei, Amin; Akhlaghi, Omid; Khani, Navid; Aytas, Tunahan; Sezer, Dilek; Tatli, Buse; Menceloglu, Yusuf Z; Koc, Bahattin; Akbulut, Ozge

    2018-03-21

    A single additive, a grafted copolymer, is designed to ensure the stability of suspensions of highly loaded iron oxide nanoparticles (IOPs) and to facilitate three-dimensional (3D) printing of these suspensions in the filament form. This poly (ethylene glycol)-grafted copolymer of N-[3(dimethylamino)propyl]methacrylamide and acrylic acid harnesses both electrostatic and steric repulsion to realize an optimum formulation for 3D printing. When used at 1.15 wt % (by the weight of IOPs), the suspension attains ∼81 wt % solid loading-96% of the theoretical limit as calculated by the Krieger-Dougherty equation. Rectangular, thick-walled toroidal, and thin-walled toroidal magnetic cores and a porous lattice structure are fabricated to demonstrate the utilization of this suspension as an ink for 3D printing. The electrical and magnetic properties of the magnetic cores are characterized through impedance spectroscopy (IS) and vibrating sample magnetometry (VSM), respectively. The IS indicates the possibility of utilizing wire-wound 3D printed cores as the inductive coils. The VSM verifies that the magnetic properties of IOPs before and after the ink formulation are kept almost unchanged because of the low dosage of the additive. This particle-targeted approach for the formulation of 3D printing inks allows embodiment of a fully aqueous system with utmost target material content.

  10. Energy house - dream house

    Energy Technology Data Exchange (ETDEWEB)

    1981-07-01

    An energy house a prefabricated house with an extensive minimization of heat losses, is air-conditioned by means of a combined heating system consisting of hot water cycle and recirculating heating. The energy system is trivalent: wind power, solar energy with heat pumps and normal oil heating.

  11. Thermal design of a modern, two floor, zero energy house in a desert compound

    KAUST Repository

    Serag-Eldin, M. A.

    2010-12-01

    The paper presents a thermal analysis and design of a fully equipped, air-conditioned, zero energy house located in a desert compound at 24.5° latitude. Unlike previous designs the home is two floors high, which makes the balancing of energy supply and demand even more challenging. The roof of the house carries an array of retractable Photovoltaic modules and cover. During day light hours the modules convert the incident sun energy into useful electrical power, while shielding the roof from direct sun-radiation. At night time, the roof cover and modules are retracted to expose the roof to the cool night-sky, thus enhancing cooling. The paper employs time-dependent modeling of Solar input and heat transfer to predict the roof, wall and window temperature distributions and cooling loads, as well as energy generated by the modules. With the aid of battery storage, the modules provide the entire energy needs of the house. The paper displays the results of energy balances for three key days of the year which demonstrate that the proposed two floor design is indeed capable of operating without external energy. © 2010 IEEE.

  12. Numerical Investigation of Floor Heating Systems in Low Energy Houses

    DEFF Research Database (Denmark)

    Weitzmann, Peter; Kragh, Jesper; Jensen, Claus Franceos

    2002-01-01

    In this paper an investigation of floor heating systems is performed with respect to heating demand and room temperature. Presently (2001) no commercially available building simulation programs that can be used to evaluate heating demand and thermal comfort in buildings with building integrated....... The model calculates heating demand, room temperatures, and thermal comfort parameters for a person in the room. The model is based on a numerical Finite Control Volume (FCV) method for the heat transfer in walls, ceiling, windows and floor. The model uses both convective and radiative heat transfer...... to the room air and between the room surfaces. The simulation model has been used to calculate heating demand and room temperature in a typical well insulated Danish single-family house with a heating demand of approximately 6000 kWh per year, for a 130 m² house. Two different types of floor heating systems...

  13. Power Load Event Detection and Classification Based on Edge Symbol Analysis and Support Vector Machine

    Directory of Open Access Journals (Sweden)

    Lei Jiang

    2012-01-01

    Full Text Available Energy signature analysis of power appliance is the core of nonintrusive load monitoring (NILM where the detailed data of the appliances used in houses are obtained by analyzing changes in the voltage and current. This paper focuses on developing an automatic power load event detection and appliance classification based on machine learning. In power load event detection, the paper presents a new transient detection algorithm. By turn-on and turn-off transient waveforms analysis, it can accurately detect the edge point when a device is switched on or switched off. The proposed load classification technique can identify different power appliances with improved recognition accuracy and computational speed. The load classification method is composed of two processes including frequency feature analysis and support vector machine. The experimental results indicated that the incorporation of the new edge detection and turn-on and turn-off transient signature analysis into NILM revealed more information than traditional NILM methods. The load classification method has achieved more than ninety percent recognition rate.

  14. Solar heating systems for houses. A design handbook for solar combisystems

    International Nuclear Information System (INIS)

    Weiss, W.

    2003-11-01

    A handbook giving guidance on systems for providing combined solar space heating and solar water heating for houses has been produced by an international team. The guidance focuses on selection of the optimum combi-system for groups of single-family houses and multi-family houses. Standard classification and evaluation procedures are described. The book should be a valuable tool for building engineers, architects, solar manufacturers and installers of solar solar energy systems, and anyone interested in optimizing combined water and space heating solar systems

  15. Single Family Loan Sale Initiative - National Offering

    Data.gov (United States)

    Department of Housing and Urban Development — The FHA Office of Housing is conducting a series of mortgage loan sales under the Single Family Loan Sale (SFLS) Initiative. The current sales structure consists of...

  16. Assessing the performance of reinforced concrete structures under impact loads

    International Nuclear Information System (INIS)

    Sharma, Akanshu; Reddy, G.R.; Vaze, K.K.; Ozbolt, Josko; Hofmann, J.

    2011-01-01

    Reinforced concrete (RC) structures housing nuclear facilities must qualify against much stringent requirements of operating and accidental loads than conventional structures. One such accidental load that must be considered while assessing the performance of safety related RC structures is impact load. It is known that the behavior of concrete/reinforced concrete structures is strongly influenced by the loading rate. The RC structural members subjected to impact loads behave quite differently as compared to the same subjected to quasi-static loading due to the strain-rate influence on strength, stiffness, and ductility as well as to the activation of inertia forces. Moreover, for concrete structures, which exhibit damage and fracture phenomena, the failure mode and cracking pattern depend significantly on loading rate. In general, there is a tendency that with the increase of loading rate the failure mode changes from mode-I to mixed mode. In order to assess the performance of existing structures against impact loads that may be generated mainly due to man-made accidental conditions, it is important to have models that can realistically predict the impact behavior of concrete structures. The present paper focuses on a relatively new approach for 3D finite element analysis of RC structures under impact loads. The approach uses rate sensitive micro-plane model as constitutive law for concrete, while the strain-rate influence is captured by the activation energy. Inertia forces are implicitly accounted for through dynamic finite element analysis. It is shown with the help of different examples that the approach can very well simulate the behavior of RC structural elements under high rate loading. (author)

  17. Oxford House Recovery Homes: Characteristics and Effectiveness

    Science.gov (United States)

    Jason, Leonard A.; Ferrari, Joseph R.

    2010-01-01

    One of the largest examples of a community-based, mutual-help residential community for high risk substance abuse individuals is Oxford House. In the U.S., over 9,800 people live in these self-run dwellings where they obtain jobs, pay utility bills, and learn to be responsible citizens. Beginning with one single rented residence in the mid 1970s, Oxford Houses now number over 1,300. These rented homes are helping to deal with drug addiction and community re-entry by providing stable housing without any limits on length of stay, a network of job opportunities, and support for abstinence. An exploration of the research on these unique settings highlights the strengths of such a community-based approach to addressing addiction. New roles for psychologists in working with these types of support systems are identified. PMID:20577571

  18. Sinus Floor Elevation with Modified Crestal Approach and Single Loaded Short Implants: A Case Report with 4 Years of Follow-Up

    Directory of Open Access Journals (Sweden)

    Michele Perelli

    2017-01-01

    Full Text Available Tooth extraction is usually followed by bone reduction. In the maxillary posterior region, this remodelling combined with sinus pneumatisation and periodontal defects may lead to a reduced basal bone height available for implant placement. Sinus floor elevation can be performed with different surgical techniques. Crestal approach has demonstrated to be effective, less invasive, and associated with a reduced morbidity. This article reports a modified sinus floor elevation by means of rotary, noncutting instruments, addition of xenograft, and 2 short-threaded implant placements. The aim of the study was to evaluate the implant’s success and intrasinus radiographical bone gain after 4 years of functional loading. The premolar implant site presented a starting basal bone height of 6 mm, while the molar site was of 2 mm. In the first surgical step, sinus floor elevation was performed mesially and the implant was inserted, and distally only sinus floor elevation was performed. After 6 months, the mesial implant was uncovered and the second implant was inserted; 4 months later, the second fixture was uncovered, and both fixtures were loaded with single provisional screw-retained crowns and later with single screw-retained porcelain fused to metal crowns. Implants integrated successfully, and crestal bone remodelling did not exceed the smooth collar. Bone gain was 3 mm for the mesial implant and more than 5 mm for the distal one.

  19. Constructing passive houses

    Energy Technology Data Exchange (ETDEWEB)

    Oehler, S. [Oehler Faigle Archkom Solar Architektur, Bretten (Germany)

    2005-07-01

    Everybody can learn to build energy-efficient. It needs theoretical and practical experience. 1997 we built the first freestanding Passive House in Europe, the Passive House Oehler. There had been a lot of questions, starting with the insecurity, whether the calculation program of the Passive House Institute, the PHPP, is working properly in our case. Nobody knew at that time because nobody tried it out before. It took us a lot of time to find out and every detail of the construction hat to be invented to meet the very high demand of thermal quality. All the following houses needed less time and had fewer open questions, adding one piece of experience with every building. 2002 we realised the biggest Passive House, the office building Energon Ulm with 420 working spaces. In the meantime we have learned a lot like how to produce prefabricated timber elements for the facades, providing good insulation, air tightness and avoiding serious thermal bridges. We have proofed, that any kind of building type can be a Passive House. And with increasing experience the freedom of design and construction is growing. Even the economical efficiency increased. The Energon Ulm is providing a much better indoor climate than any other office building and was build 10 % cheaper than an average German office building. At present the Passive House Standard is the most efficient solution for the user to live in the desired comfort zone between 20 C and 25 C. This zone of individual feeling-well can be described with the term ''operative temperature''. This term is defined by factors like air temperature, radiation temperature of warm and cold surfaces, air speed and humidity. The result of all these factors has to be within 18 C to 25 C without accepting one of the factors getting extreme.

  20. Effect of a change in housing conditions on body weight, behavior and brain neurotransmitters in male C57BL/6J mice.

    Science.gov (United States)

    Pasquarelli, Noemi; Voehringer, Patrizia; Henke, Julia; Ferger, Boris

    2017-08-30

    The development of modern housing regimes such as individually ventilated cage (IVC) systems has become very popular and attractive in order to reduce spreading of pathogenic organisms and to lower the risk to develop a laboratory animal allergy for staff members. Additionally, optimal housing of laboratory animals contributes to improve animal health status and ensures high and comparable experimental and animal welfare standards. However, it has not been clearly elucidated whether 1) a change to IVC systems have an impact on various physiological phenotypic parameters of mice when compared to conventional, standard cages and 2) if this is further affected by changing from social to single housing. Therefore, we investigated the influence of a change in housing conditions (standard cages with social housing changed to standard or IVC cages combined with social or single housing) on body weight, behavior and a neurochemical fingerprint of male C57BL/6J mice. Body weight progression was significantly reduced when changing mice to single or social IVC cages as well as in single standard cages when compared to social standard housing. Automated motor activity measurement in the open field showed that mice maintained in social husbandry with standard cages displayed the lowest exploratory behavior but the highest activity difference upon amphetamine treatment. Elevated plus maze test revealed that a change to IVC single and social housing as well as single standard housing produced anxiety-related behavior when compared to maintenance in social standard housing. Additionally, postmortem neurochemical analysis of the striatum using high-performance liquid chromatography coupled to electrochemical detection showed significant differences in striatal dopamine and serotonin turnover levels. In summary, our data indicate a crucial influence of a change in housing conditions on several mouse phenotype parameters. We propose that the maintenance of well-defined housing

  1. Passive houses in Sweden. Experiences from design and construction phase

    Energy Technology Data Exchange (ETDEWEB)

    Jansson, Ulla

    2008-07-01

    The sector of residential buildings and service organizations uses 36% of the total energy in Sweden. In June 2006, it was decided by the Swedish parliament that the energy use in residential buildings and premises should decrease by 20% per heated unit area before 2020. To reach this goal, more energy efficient buildings must be produced as well as energy efficient improvements must be performed on the existing building stock. One way to reduce the energy use in buildings is to build passive houses. A passive house is a mechanically ventilated building that with a highly insulated and air tight building envelope uses a minimum of energy for heating. The method used in this research is to practically participate in four passive house demonstration projects. The results expected are to find guiding principles and tools needed for passive house planning and make the system solutions usable for planning in more general terms. Joining as a part of the planning group; advice and help is given to architects, consultants and to the client. The demonstration projects studied are located in the south-west of Sweden. Three of the projects are new constructions and one is a renovation project. In the centre of Vanirom 40 rental apartments were built in 2005/2006 according to the passive house standard. Solar collectors on the roof contribute to the domestic hot water production. Every apartment has its own mechanical ventilation system with efficient heat recovery. Auxiliary heating is supplied by electricity. The load bearing structure were made of concrete and cast at site. The exterior walls and roof were made of wooden frame construction and mounted at site. The tenants moved in during summer 2006. The passive house project in Failure's consists of three houses with 12 rental apartments. The air is supplied by mechanical ventilation with an air to air heat exchanger, one in each apartment. The domestic hot water is prepared by solar collectors and auxiliary heating

  2. Lead and other elements in house dust of Japanese residences – Source of lead and health risks due to metal exposure

    International Nuclear Information System (INIS)

    Yoshinaga, Jun; Yamasaki, Kumiko; Yonemura, Ayumi; Ishibashi, Yuri; Kaido, Takaya; Mizuno, Kodai; Takagi, Mai; Tanaka, Atsushi

    2014-01-01

    The levels of 25 elements in house dust collected from 100 general Japanese residences were measured. Factor analysis was applied on the multi-element data to explore source of Pb (median concentration 49.1 mg/kg) in house dust. Six factors were extracted and Pb was found to have great loading on the fifth factor with Sb and Sn, suggesting solder (Sn), and plastic and metals (Sb) may be the sources of Pb in the house dust of Japanese residences. No significant loading was found on soil-related factors indicating non-significant contribution of Pb in track-in soil. Seven heavy metals (Cd, Cu, Mo, Pb, Sb, Sn, and Zn) were found in house dust at >10 times more condensed than crustal abundance. Health risk of these elements to children via the ingestion of house dust was estimated based on the comparison with tolerable daily intake and found to be non-significant for most of the elements. - Highlights: • Multi-element analysis was carried out for house dust from households in Japan. • Factor analysis was applied on the multivariate data set. • The abundance of lead had a close relationship with antimony and tin in house dust. • Health risk of heavy metals in house dust for children was not serious. - Major source of Pb in house dust of Japanese residences was not track-in soil but unknown materials that contain Pb and Sb and/or Sn

  3. Procedures for Calculating Residential Dehumidification Loads

    Energy Technology Data Exchange (ETDEWEB)

    Winkler, Jon [National Renewable Energy Lab. (NREL), Golden, CO (United States); Booten, Chuck [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-06-01

    Residential building codes and voluntary labeling programs are continually increasing the energy efficiency requirements of residential buildings. Improving a building's thermal enclosure and installing energy-efficient appliances and lighting can result in significant reductions in sensible cooling loads leading to smaller air conditioners and shorter cooling seasons. However due to fresh air ventilation requirements and internal gains, latent cooling loads are not reduced by the same proportion. Thus, it's becoming more challenging for conventional cooling equipment to control indoor humidity at part-load cooling conditions and using conventional cooling equipment in a non-conventional building poses the potential risk of high indoor humidity. The objective of this project was to investigate the impact the chosen design condition has on the calculated part-load cooling moisture load, and compare calculated moisture loads and the required dehumidification capacity to whole-building simulations. Procedures for sizing whole-house supplemental dehumidification equipment have yet to be formalized; however minor modifications to current Air-Conditioner Contractors of America (ACCA) Manual J load calculation procedures are appropriate for calculating residential part-load cooling moisture loads. Though ASHRAE 1% DP design conditions are commonly used to determine the dehumidification requirements for commercial buildings, an appropriate DP design condition for residential buildings has not been investigated. Two methods for sizing supplemental dehumidification equipment were developed and tested. The first method closely followed Manual J cooling load calculations; whereas the second method made more conservative assumptions impacting both sensible and latent loads.

  4. Stress analysis of fuelling machine magazine housing of PHWR

    International Nuclear Information System (INIS)

    Singh, R.K.; Mehra, V.K.; Charan, J.J.; Kakodkar, A.

    1983-01-01

    PWR has fuelling machines for on-line refuelling of the core. Magazine housing of this fuelling machine is a thick pressure vessel. It has a cylindrical vessel with flat head on one side and reservable flange closure on the other side. The vessel has many small and big openings. This paper describes the two sets of experiments conducted for its stress analysis. First set of experiment was conducted on a 1:5 photoelastic model which was stress frozen under load of internal pressure. The second set of experiment involved strain gauge measurements at some important locations of the magazine housing. The paper summarises results of the experiments. In conclusion comparison is made between the experimental results and the results of finite element analysis. (orig.)

  5. Changing distribution and geometry of S′ in Al–Cu–Mg single crystals during stress aging by controlling the loading orientation

    International Nuclear Information System (INIS)

    Chen, Jiqiang; Chen, Zhiguo; Guo, Xiaobin; Deng, Yunlai

    2016-01-01

    The precipitation behavior of S′ phase in Al–Cu–Mg single crystals during stress-free and stress aging was investigated by transmission electron microscopy (TEM). Different compressive stress magnitudes and loading orientations were applied to determine their effects on the precipitation of S′ in Al–Cu–Mg alloy during stress aging. The results indicate that a noticeable preferential orientation of S′ is generated in the sample under applied compressive stress of 33 MPa loading along close to [001] Al , whilst no obviously preferential orientation of S′ can be observed in the sample loaded along close to [101] Al under the same applied stress or even larger applied stress. The precipitation distribution of S′ phase during stress aging can be changed by the loading orientation of the applied stress. Moreover, compressive stress aging may lead to S′ phase shorter in length, and the length of S′ phase shows a decreasing tendency with increasing applied stress, which are associated with the positive misfit between S′ and Al matrix.

  6. Plastic limit loads for cylindrical shell intersections under combined loading

    International Nuclear Information System (INIS)

    Skopinsky, V.N.; Berkov, N.A.; Vogov, R.A.

    2015-01-01

    In this research, applied methods of nonlinear analysis and results of determining the plastic limit loads for shell intersection configurations under combined internal pressure, in-plane moment and out-plane moment loadings are presented. The numerical analysis of shell intersections is performed using the finite element method, geometrically nonlinear shell theory in quadratic approximation and plasticity theory. For determining the load parameter of proportional combined loading, the developed maximum criterion of rate of change of relative plastic work is employed. The graphical results for model of cylindrical shell intersection under different two-parameter combined loadings (as generalized plastic limit load curves) and three-parameter combined loading (as generalized plastic limit load surface) are presented on the assumption that the internal pressure, in-plane moment and out-plane moment loads were applied in a proportional manner. - Highlights: • This paper presents nonlinear two-dimensional FE analysis for shell intersections. • Determining the plastic limit loads under combined loading is considered. • Developed maximum criterion of rate of change of relative plastic work is employed. • Plastic deformation mechanism in shell intersections is discussed. • Results for generalized plastic limit load curves of branch intersection are presented

  7. Simplified Space Conditioning in Low-Load Homes: Results from Pittsburgh, Pennsylvania, New Construction Unoccupied Test House

    Energy Technology Data Exchange (ETDEWEB)

    Poerschke, A.; Stecher, D.

    2014-06-01

    Field testing was performed in a new construction unoccupied test house in Pittsburgh, Pennsylvania. Four air-based heating, ventilation, and air conditioning distribution systems--a typical airflow ducted system to the bedrooms, a low airflow ducted system to the bedrooms, a system with transfer fans to the bedrooms, and a system with no ductwork to the bedrooms--were evaluated during heating, cooling, and midseason conditions. The relative ability of each system was assessed with respect to relevant Air Conditioning Contractors of America and ASHRAE standards for house temperature uniformity and stability, respectively.

  8. Simplified Space Conditioning in Low-Load Homes: Results from Pittsburgh, Pennsylvania, New Construction Unoccupied Test House

    Energy Technology Data Exchange (ETDEWEB)

    Poerschke, Andrew [IBACOS, Inc., Pittsburgh, PA (United States); Stecher, Dave [IBACOS, Inc., Pittsburgh, PA (United States)

    2014-06-01

    Field testing was performed in a new construction unoccupied test house in Pittsburgh, PA. Four air-based heating, ventilation, and air conditioning distribution systems—a typical airflow ducted system to the bedrooms, a low airflow ducted system to the bedrooms, a system with transfer fans to the bedrooms, and a system with no ductwork to the bedrooms—were evaluated during heating, cooling, and midseason conditions. The relative ability of each system was assessed with respect to relevant Air Conditioning Contractors of America and ASHRAE standards for house temperature uniformity and stability, respectively.

  9. Japanese Social Exclusion and Inclusion from a Housing Perspective

    Directory of Open Access Journals (Sweden)

    Yoshihiro Okamoto

    2016-10-01

    Full Text Available This paper examines conditions of social exclusion and attempts at social inclusion in Japan from a housing perspective. Companies, households and the government have previously supported housing in Japan. However, corporate welfare was withdrawn following the globalization of the economy from the 1990s onwards, support from families and communities declined due to a reduction in household size, and governmental housing support has shifted away from direct support. A reduction in income and unstable work left many people with unstable housing. Certain workers, such as foreigners performing dispatched labour, could not maintain continuous work under the influence of the Lehman Brothers’ bankruptcy in 2008. Household size has shrunk according to changes in the industrial structure, and the number of households that cannot sustain housing is increasing. Such vulnerable households—elderly people, the handicapped, low-income earners and single parents—can become excluded from the rental housing market. On the other hand, governmental measures are promoting local dwellings and maintaining the condition for a dwelling service. Activities, such as local community support of the homeless have been initiated by various Non-profit Organisations (NPOs and NPO activities are increasingly exemplifying measures to achieve social inclusion.

  10. Peak load-impulse characterization of critical pulse loads in structural dynamics

    International Nuclear Information System (INIS)

    Abrahamson, G.R.; Lindberg, H.E.

    1975-01-01

    In presenting the characterization scheme, some general features are described first. A detailed analysis is given for the rigid-plastic system of one degree of freedom to illustrate the calculation of critical load curves in terms of peak load and impulse. This is followed by the presentation of critical load curves for uniformly loaded rigid-plastic beams and plates and for dynamic buckling of cylindrical shells under uniform lateral loads. The peak load-impulse characterization of critical pulse loads is compared with the dynamic load factor characterization, and some aspects of the history of the peak load-pulse scheme are presented. (orig./HP) [de

  11. Data-driven regionalization of housing markets

    NARCIS (Netherlands)

    Helbich, M.; Brunauer, W.; Hagenauer, J.; Leitner, M.

    2013-01-01

    This article presents a data-driven framework for housing market segmentation. Local marginal house price surfaces are investigated by means of mixed geographically weighted regression and are reduced to a set of principal component maps, which in turn serve as input for spatial regionalization. The

  12. 7 CFR 1944.664 - Housing preservation and replacement housing assistance.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 13 2010-01-01 2009-01-01 true Housing preservation and replacement housing...) RURAL HOUSING SERVICE, RURAL BUSINESS-COOPERATIVE SERVICE, RURAL UTILITIES SERVICE, AND FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE (CONTINUED) PROGRAM REGULATIONS (CONTINUED) HOUSING Housing...

  13. Evaluating Moisture Control of Variable-Capacity Heat Pumps in Mechanically Ventilated, Low-Load Homes in Climate Zone 2A

    Energy Technology Data Exchange (ETDEWEB)

    Martin, Eric [Univ. of Central Florida, Orlando, FL (United States). Florida Solar Energy Center; Withers, Chuck [Univ. of Central Florida, Orlando, FL (United States). Florida Solar Energy Center; McIlvaine, Janet [Univ. of Central Florida, Orlando, FL (United States). Florida Solar Energy Center; Chasar, Dave [Univ. of Central Florida, Orlando, FL (United States). Florida Solar Energy Center; Beal, David [Univ. of Central Florida, Orlando, FL (United States). Florida Solar Energy Center

    2018-02-07

    The well-sealed, highly insulated building enclosures constructed by today's home building industry coupled with efficient lighting and appliances are achieving significantly reduced heating and cooling loads. These low-load homes can present a challenge when selecting appropriate space-conditioning equipment. Conventional, fixed-capacity heating and cooling equipment is often oversized for small homes, causing increased first costs and operating costs. Even if fixed-capacity equipment can be properly specified for peak loads, it remains oversized for use during much of the year. During these part-load cooling hours, oversized equipment meets the target dry-bulb temperatures very quickly, often without sufficient opportunity for moisture control. The problem becomes more acute for high-performance houses in humid climates when meeting ASHRAE Standard 62.2 recommendations for wholehouse mechanical ventilation.

  14. Influence of Interface Gap on the Stress Behaviour of Smart Single Lap Joints Under Time Harmonic Load

    Directory of Open Access Journals (Sweden)

    Ivanova Jordanka

    2017-06-01

    Full Text Available Adhesive joints are frequently used in different composite structures due to their improved mechanical performance and better understanding of the failure mechanics. The application of such structures can be seen in aerospace and high technology components. The authors developed and applied modified shear lag analysis to investigate the hygrothermalpiezoelectric response of a smart single lap joint at environmental conditions (with/without an interface gap along the overlap zone and under dynamic time harmonic mechanical and electric loads. The main key is the study of the appearance of possible delamination along the interface. As illustrative examples, the analytical closed form solution of the structure shear and the axial stresses response, as well as the interface debond length, including influence of mechanical, piezoelectric, thermal characteristics and frequencies is performed and discussed. All results are presented in figures. The comparison of the shear stress and electric fields for both cases of overlap zone (continuous or with a gap is also shown in figures and discussed.

  15. A Life-Cycle Analysis of Social Security with Housing

    OpenAIRE

    Chen, Kaiji

    2009-01-01

    This paper incorporates two features of housing in a life-cycle analysis of social security: housing as a durable good and housing market frictions. We find that with housing as a durable good unfunded social security substantially crowds out housing consumption throughout the life cycle. By contrast, aggregate non-durable consumption is higher when social security is present, although it is postponed until late in life. Moreover, in the presence of housing market frictions, social security l...

  16. ANALYSIS OF CLIMATIC AND SOCIAL PERFORMANCES OF LOW COST TERRACE HOUSING (LCTH: INTRODUCING THE AFFORDABLE QUALITY HOUSING (AQH CONCEPT IN MALAYSIA

    Directory of Open Access Journals (Sweden)

    Noor Hanita Abdul Majid

    2009-03-01

    Full Text Available Low cost terrace housing (LCTH is the most common form and popular typology of public housing in Malaysia. The provision of the houses is deemed to be the most suitable to fulfil the needs to house low income families, and also as an alternative to high rise low cost housing. Since the implementation of these housing types, development on the layout and sizes of the house has taken place to provide for better living conditions. Literature review on the current LCTH suggested that there are deficiencies in fulfilling the requirements to provide quality and affordable housing for the low income families. This paper presents the scenario of the LCTH design based on secondary findings by researchers on housing in Malaysia. The secondary data provided the grounds for the proposal of affordable and quality housing (AQH to handle the problems that occurred at the LCTH. Both social and climatic considerations are included in the AQH, addressing issues on privacy, segregation of genders and community interaction; along with thermal comfort and natural ventilation. Decisions on the AQH are carefully extracted from a comparison analysis in the view to improve the current conditions. In order to verify some of the decisions on climatic design strategies, simulation results are presented. The results indicated that the design decisions have managed to improve on the natural ventilation conditions at the low cost houses. With reservations on the social conditions that are yet to be tested at the actual houses, the AQH has proven to be a step forward towards the provision of a better living environment.

  17. Understanding Housing Delays and Relocations Within the Housing First Model.

    Science.gov (United States)

    Zerger, Suzanne; Pridham, Katherine Francombe; Jeyaratnam, Jeyagobi; Hwang, Stephen W; O'Campo, Patricia; Kohli, Jaipreet; Stergiopoulos, Vicky

    2016-01-01

    This study explores factors contributing to delays and relocations during the implementation of the Housing First model in Toronto, Ontario. While interruptions in housing tenure are expected en route to recovery and housing stability, consumer and service provider views on finding and keeping housing remain largely unknown. In-person interviews and focus groups were conducted with 48 study participants, including 23 case managers or housing workers and 25 consumers. The following three factors contributed to housing delays and transfers: (1) the effectiveness of communication and collaboration among consumers and service providers, (2) consumer-driven preferences and ambivalence, and (3) provider prioritization of consumer choice over immediate housing access. Two strategies--targeted communications and consumer engagement in housing searches--supported the housing process. Several factors affect the timing and stability of housing. Communication between and among providers and consumers, and a shared understanding of consumer choice, can further support choice and recovery.

  18. Strain Measurement System Developed for Biaxially Loaded Cruciform Specimens

    Science.gov (United States)

    Krause, David L.

    2000-01-01

    A new extensometer system developed at the NASA Glenn Research Center at Lewis Field measures test area strains along two orthogonal axes in flat cruciform specimens. This system incorporates standard axial contact extensometers to provide a cost-effective high-precision instrument. The device was validated for use by extensive testing of a stainless steel specimen, with specimen temperatures ranging from room temperature to 1100 F. In-plane loading conditions included several static biaxial load ratios, plus cyclic loadings of various waveform shapes, frequencies, magnitudes, and durations. The extensometer system measurements were compared with strain gauge data at room temperature and with calculated strain values for elevated-temperature measurements. All testing was performed in house in Glenn's Benchmark Test Facility in-plane biaxial load frame.

  19. Sustainable Transition of Housing and Construction

    DEFF Research Database (Denmark)

    This book presents recent research into sustainable transition of housing and construction through contributions from researchers and knowledge providers that have worked with change processes within housing and construction. The contributors represent different research and development...... environments, each with their own tradition and with a number of different research projects behind them in the field. Their common ground is that they have researched and analyzed construction, dwellings and housing areas with a view to energy-, environment- and climate-oriented transition of the housing...... and construction sector, with a focus on either political, socio-cultural, technical or design challenges. The contributions thus represent both technological, architectural, sociological and political aspects of the Danish housing and construction field. The aim of the book has not been to add another book...

  20. Innovate the Land Supply Pattern and Stabilize the Housing

    Institute of Scientific and Technical Information of China (English)

    WANG Junjie; Chen haibo

    2015-01-01

    In the process of building a harmonious socialist society, the protection of people' s livelihood is the priority, and to solve the housing problem of over one billion residents is the top priority. The present thesis begins with the land supply mechanism, and do researches on the style, the source and the type of land supply. With the analysis of land finance, the present thesis finally put forward the measures to innovate the land supply pattern, to increase the supply of low-income housing, to reform the way of land supply and to explore the circulating pattern of normative collective construction land that comes to is on the market. Meanwhile, it combines the present house property tax reform, putting forward the idea that imposing land property tax should be a way to inhibit the behavior of speculation. The present thesis aims at keeping the housing price at a reasonable level so that the purpose of stabilizing the housing price can he achieved.

  1. Clinical characteristics in patients showing ischemic electrocardiographic changes during adenosine triphosphate loading single-photon emission computed tomography

    International Nuclear Information System (INIS)

    Ohtaki, Yuka; Chikamori, Taishiro; Hida, Satoshi; Tanaka, Hirokazu; Igarashi, Yuko; Hatano, Tsuguhisa; Usui, Yasuhiro; Miyagi, Manabu; Yamashina, Akira

    2010-01-01

    Although ischemic electrocardiographic (ECG) changes during dipyridamole or adenosine infusion have been reported as a marker for severe coronary artery disease (CAD), few studies have focused on ST-segment changes with adenosine triphosphate (ATP)-loading myocardial single-photon emission computed tomography (SPECT). Between January 2003 and August 2008, 4650 consecutive patients underwent ATP-loading SPECT. After 1412 patients with left bundle branch block, pacemaker rhythm, or previous coronary revascularization were excluded, 16 out of 3238 patients (0.5%) showed ischemic ST-segment depression during ATP-loading myocardial SPECT. They were aged 67±11 years; 10 were men and 6 women. Of these patients, 8 demonstrated perfusion abnormalities, whereas the remaining 8 showed normal myocardial perfusion imaging. In 6 of the 8 patients with abnormal SPECT, coronary angiography was performed, revealing left main trunk disease in 1 patient, 3-vessel disease in 4, 1-vessel disease with proximal left ascending artery occlusion in 1, and an insignificant lesion in 1. By contrast, no major cardiac event was observed in the 8 patients with normal SPECT during follow-up for an average of 2 years. The prevalence of ischemic ST-segment changes during ATP loading is very rare. However, this finding should be taken into account since almost half of the patients, particularly those with perfusion abnormalities, may have severe CAD which requires coronary revascularization. (author)

  2. Development and application of a model to calculate the distribution of radon in houses

    International Nuclear Information System (INIS)

    Haider, B.; Papamokos, E.; Ferron, G.; Peter, J.; Unverfaerth, L.

    1990-01-01

    In order to produce a radon profile of the examined houses, an electronic measuring process was used to determine the concentration of radon decomposition products. The measurements were made inside flats with the doors closed, in vertical air exchange between the cellars and the storeys of houses and in the cellar itself. The measured decomposition product and measured gas concentrations show that, apart from the cellar floor, part of the building material makes a considerable contribution to emanation of radon and thoron. It was found that a model for calculating the loading of the inhabitants of a house with radon is not yet available due to the complicated flat geometry and the activities of the inhabitants. (DG) [de

  3. Housing management and maintenance practise of Dutch housing associations

    NARCIS (Netherlands)

    Straub, A.

    This paper summarises the state-of-the-art in housing management and maintenance practise of Dutch housing associations based on a survey conducted among almost all housing associations. We address the question what the current developments are in housing management and maintenance practice in the

  4. 24 CFR 92.252 - Qualification as affordable housing: Rental housing.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Qualification as affordable housing: Rental housing. 92.252 Section 92.252 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development HOME INVESTMENT PARTNERSHIPS PROGRAM Project Requirements § 92.252...

  5. 24 CFR 8.28 - Housing certificate and housing voucher programs.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Housing certificate and housing voucher programs. 8.28 Section 8.28 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development NONDISCRIMINATION BASED ON HANDICAP IN FEDERALLY ASSISTED PROGRAMS AND...

  6. Double-Row Capsulolabral Repair Increases Load to Failure and Decreases Excessive Motion.

    Science.gov (United States)

    McDonald, Lucas S; Thompson, Matthew; Altchek, David W; McGarry, Michelle H; Lee, Thay Q; Rocchi, Vanna J; Dines, Joshua S

    2016-11-01

    Using a cadaver shoulder instability model and load-testing device, we compared biomechanical characteristics of double-row and single-row capsulolabral repairs. We hypothesized a greater reduction in glenohumeral motion and translation and a higher load to failure in a mattress double-row capsulolabral repair than in a single-row repair. In 6 matched pairs of cadaveric shoulders, a capsulolabral injury was created. One shoulder was repaired with a single-row technique, and the other with a double-row mattress technique. Rotational range of motion, anterior-inferior translation, and humeral head kinematics were measured. Load-to-failure testing measured stiffness, yield load, deformation at yield load, energy absorbed at yield load, load to failure, deformation at ultimate load, and energy absorbed at ultimate load. Double-row repair significantly decreased external rotation and total range of motion compared with single-row repair. Both repairs decreased anterior-inferior translation compared with the capsulolabral-injured condition, however, no differences existed between repair types. Yield load in the single-row group was 171.3 ± 110.1 N, and in the double-row group it was 216.1 ± 83.1 N (P = .02). Ultimate load to failure in the single-row group was 224.5 ± 121.0 N, and in the double-row group it was 373.9 ± 172.0 N (P = .05). Energy absorbed at ultimate load in the single-row group was 1,745.4 ± 1,462.9 N-mm, and in the double-row group it was 4,649.8 ± 1,930.8 N-mm (P = .02). In cases of capsulolabral disruption, double-row repair techniques may result in decreased shoulder rotational range of motion and improved load-to-failure characteristics. In cases of capsulolabral disruption, repair techniques with double-row mattress repair may provide more secure fixation. Double-row capsulolabral repair decreases shoulder motion and increases load to failure, yield load, and energy absorbed at yield load more than single-row repair. Published by

  7. Wave induced extreme hull girder loads on containerships

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher; Pedersen, Preben Terndrup; Shi, Bill

    2009-01-01

    This paper provides simple but rational procedures for prediction of extreme wave – induced sectional hull girder forces with reasonable engineering accuracy. The procedures take into account main ship hull characteristics such as: length, breadth, draught, block coefficient, bow flare coefficient......, forward speed and hull flexibility. The vertical hull girder loads are evaluated for specific operational profiles. Firstly a quadratic strip theory is presented which can give separate predictions for the hogging and sagging bending moments and shear forces and for hull girder loads. Then this procedure...... is based on rational methods it can be applied for novel single hull ship types not presently covered by the rules of the classification societies or to account for specific operational profiles....

  8. ANALYSIS OF THE EFFECTS OF THE ROOFING DESIGN ON HEAT STRESS IN DAIRY COW HOUSING

    OpenAIRE

    Paolo Liberati

    2008-01-01

    A simulation model determining the heat flow exchange between housed animals and the roofing was developed considering various relevant factors: constructive materials, slope, height, orientation, latitude, external air temperature, solar load, animal position. Results show that the most important factor to reduce heat load is the insulation. For non-insulated roofing the slope and the orientation are the most relevant factors. Considering the total exchanged energy, the non insulated roof ha...

  9. Wooden houses in detail. Holzhaeuser im Detail

    Energy Technology Data Exchange (ETDEWEB)

    Ruske, W. (ed.)

    1986-01-01

    Under the serial title 'Planning and construction of wooden houses', WEKA will publish a number of books of which this is the first. Details of design and construction are presented, e.g.: Details of modern one-family houses; Fundamentals of design and hints for planning of wooden houses and compact wooden structures; Constructional ecology, wood protection, thermal insulation, sound insulation; Modular systems for domestic buildings; The 'bookshelf-type' house at the Berlin International Construction Exhibition (IBA); Experience with do-it-yourself systems. With 439 figs.

  10. An electrical load measurements dataset of United Kingdom households from a two-year longitudinal study.

    Science.gov (United States)

    Murray, David; Stankovic, Lina; Stankovic, Vladimir

    2017-01-05

    Smart meter roll-outs provide easy access to granular meter measurements, enabling advanced energy services, ranging from demand response measures, tailored energy feedback and smart home/building automation. To design such services, train and validate models, access to data that resembles what is expected of smart meters, collected in a real-world setting, is necessary. The REFIT electrical load measurements dataset described in this paper includes whole house aggregate loads and nine individual appliance measurements at 8-second intervals per house, collected continuously over a period of two years from 20 houses. During monitoring, the occupants were conducting their usual routines. At the time of publishing, the dataset has the largest number of houses monitored in the United Kingdom at less than 1-minute intervals over a period greater than one year. The dataset comprises 1,194,958,790 readings, that represent over 250,000 monitored appliance uses. The data is accessible in an easy-to-use comma-separated format, is time-stamped and cleaned to remove invalid measurements, correctly label appliance data and fill in small gaps of missing data.

  11. An electrical load measurements dataset of United Kingdom households from a two-year longitudinal study

    Science.gov (United States)

    Murray, David; Stankovic, Lina; Stankovic, Vladimir

    2017-01-01

    Smart meter roll-outs provide easy access to granular meter measurements, enabling advanced energy services, ranging from demand response measures, tailored energy feedback and smart home/building automation. To design such services, train and validate models, access to data that resembles what is expected of smart meters, collected in a real-world setting, is necessary. The REFIT electrical load measurements dataset described in this paper includes whole house aggregate loads and nine individual appliance measurements at 8-second intervals per house, collected continuously over a period of two years from 20 houses. During monitoring, the occupants were conducting their usual routines. At the time of publishing, the dataset has the largest number of houses monitored in the United Kingdom at less than 1-minute intervals over a period greater than one year. The dataset comprises 1,194,958,790 readings, that represent over 250,000 monitored appliance uses. The data is accessible in an easy-to-use comma-separated format, is time-stamped and cleaned to remove invalid measurements, correctly label appliance data and fill in small gaps of missing data.

  12. Field survey of a sustainable sanitation system in a residential house.

    Science.gov (United States)

    Nakagawa, Naoko; Otaki, Masahiro; Miura, Shinji; Hamasuna, Hironobu; Ishizaki, Katsuyoshi

    2006-01-01

    Sustainable sanitation is an approach for more ecological and sustainable water resources management. In this paper, we proposed one of the new integrated waste treatment systems: an "sustainable sanitation system" that includes separation of the black water from water system by a non-flushing toilet (bio-toilet), and a gray water treatment based on a biological and ecological concept. Sustainable sanitation system also converts the domestic waste to soil conditioners and fertilizers, for farmland use. As one of the case studies, Environmentally Symbiotic Housing in which people actually live using the bio-toilet for the black water treatment and the household wastewater treatment facility for the gray water was introduced. The availability of this system was investigated by analyzing the sawdust used in the bio-toilet and the quality of the effluent in the household wastewater treatment facility. As the result, the water content of the sawdust did not exceed 60% in any of the sampling points and the BOD and COD of the effluent of the household wastewater treatment facility were below 10 and 20 mg/L respectively, due to the low loading. Compared to the pollution load on the water environment created by the conventional system, it was found that the effluent of the house has a lower load than the tertiary treatment and the volume of the water consumption is 75% of the conventional system.

  13. Load response and gap formation in a single-row cruciate suture rotator cuff repair.

    Science.gov (United States)

    Huntington, Lachlan; Richardson, Martin; Sobol, Tony; Caldow, Jonathon; Ackland, David C

    2017-06-01

    Double-row rotator cuff tendon repair techniques may provide superior contact area and strength compared with single-row repairs, but are associated with higher material expenses and prolonged operating time. The purpose of this study was to evaluate gap formation, ultimate tensile strength and stiffness of a single-row cruciate suture rotator cuff repair construct, and to compare these results with those of the Mason-Allen and SutureBridge repair constructs. Infraspinatus tendons from 24 spring lamb shoulders were harvested and allocated to cruciate suture, Mason-Allen and SutureBridge repair groups. Specimens were loaded cyclically between 10 and 62 N for 200 cycles, and gap formation simultaneously measured using a high-speed digital camera. Specimens were then loaded in uniaxial tension to failure, and construct stiffness and repair strength were evaluated. Gap formation in the cruciate suture repair was significantly lower than that of the Mason-Allen repair (mean difference = 0.6 mm, P = 0.009) and no different from that of the SutureBridge repair (P > 0.05). Both the cruciate suture repair (mean difference = 15.7 N/mm, P = 0.002) and SutureBridge repair (mean difference = 15.8 N/mm, P = 0.034) were significantly stiffer than that of the Mason-Allen repair; however, no significant differences in ultimate tensile strength between repair groups were discerned (P > 0.05). The cruciate suture repair construct, which may represent a simple and cost-effective alternative to double-row and double-row equivalent rotator cuff repairs, has comparable biomechanical strength and integrity with that of the SutureBridge repair, and may result in improved construct longevity and tendon healing compared with the Mason-Allen repair. © 2017 Royal Australasian College of Surgeons.

  14. Study on Heat Utilization in an Attached Sunspace in a House with a Central Heating, Ventilation, and Air Conditioning System

    Directory of Open Access Journals (Sweden)

    Qingsong Ma

    2018-05-01

    Full Text Available Based on numerical simulations, the heating load reduction effect of an attached sunspace in winter was determined, and the effective heat utilization method and sunspace design were explored. In this paper, we studied the heating load reduction effect using heat from the sunspace and temperature fluctuation of each room at the time of heat use from the sunspace (sending air from the sunspace to the heating, ventilation, and air conditioning (HVAC machine room and taking the air to the adjacent rooms. In the case of the all-day HVAC system, it was confirmed that a larger capacity of sunspace and not sending air from the sunspace to the adjacent room demonstrated a better heating-load reduction effect. Compared with Model Iw (a house with a window on the exterior of the sunspace opened to external air, Model I (a house with an attached sunspace on the second floor could save approximately 41% of the total energy. Model II (a house with the attached sunspace both on the first and second floors could save approximately 84% of the total energy. Sending heat from the sunspace to the adjacent room led to temperature increases in the adjacent rooms. However, if the construction plan is to have the sunspace only on the second floor, the house should be carefully designed, for example, by placing a living room on the second floor.

  15. Effects of filter housing and ductwork configuration on air flow uniformity inside air cleaning filter housings

    International Nuclear Information System (INIS)

    Paul, J.D.

    1993-01-01

    Each new HEPA filter installation presents a different physical configuration based on the system requirements, the available space and designer preference. Each different configuration can result in variations of air flow uniformity inside the filter housing across the filter banks. This paper presents the results of air flow uniformity testing for six different filter housing/ductwork configurations and discusses if any of those variations in air flow uniformity is attributable to the difference in the physical arrangements for the six cases

  16. Assessment of Industrial Load for Demand Response across Western Interconnect

    Energy Technology Data Exchange (ETDEWEB)

    Alkadi, Nasr E [ORNL; Starke, Michael R [ORNL; Ma, Ookie [United States Department of Energy (DOE), Office of Efficiency and Renewable Energy (EERE)

    2013-11-01

    Demand response (DR) has the ability to both increase power grid reliability and potentially reduce operating system costs. Understanding the role of demand response in grid modeling has been difficult due to complex nature of the load characteristics compared to the modeled generation and the variation in load types. This is particularly true of industrial loads, where hundreds of different industries exist with varying availability for demand response. We present a framework considering industrial loads for the development of availability profiles that can provide more regional understanding and can be inserted into analysis software for further study. The developed framework utilizes a number of different informational resources, algorithms, and real-world measurements to perform a bottom-up approach in the development of a new database with representation of the potential demand response resource in the industrial sector across the U.S. This tool houses statistical values of energy and demand response (DR) potential by industrial plant and geospatially locates the information for aggregation for different territories without proprietary information. This report will discuss this framework and the analyzed quantities of demand response for Western Interconnect (WI) in support of evaluation of the cost production modeling with power grid modeling efforts of demand response.

  17. Seismic Load Rating Procedure for Welded Steel Frames Oligo-cyclic Fatigue

    International Nuclear Information System (INIS)

    Ratiu, Mircea D.; Moisidis, Nicolae T.

    2004-01-01

    A dynamic load rating approach for seismic qualification of cold-formed steel welded frames is presented. Allowable seismic loads are developed from cyclic and monotonic tests of standard cold-formed steel components commonly used for piping and electrical raceway supports. The method permits simplified qualification of all connections of frame components through a single load comparison. Test input consists of rotation/cycles-to-failure data and monotonic moment/rotation data. Cyclic data are statistically evaluated to determine an acceptable maximum seismic rotation for the connection. The allowable seismic load is determined from the corresponding static rotation. Application to seismic qualification procedures is discussed. (authors)

  18. A Countrywide House Price Index for 152 Years

    DEFF Research Database (Denmark)

    Lunde, Jens; Helding Madsen, Anders; Lundbæk Laursen, Maria

    for Herengracht (the Netherlands), Norway, USA, France, and recently also Australia. Until now, the here presented house price index for Denmark is the longest countrywide house price index ever been published, based on official data, and qualitatively probably the best long house price index....... in house prices is depicted. The Danish house price index covering all the 152 years is in reality a simple average sale price index for houses. From 1920 on it was possible to construct another and a “pure” house price index, based on the Sales Price Appraisal Ratio (SPAR) method. Several challenges...... for creating the house price index arose, especially in converting the previous registered house prices in the statistics into current market prices. In real terms, the average sale price index increased more than the SPAR index for the years where the two indices were compared, and the difference express...

  19. 24 CFR 982.617 - Shared housing: Rent and voucher housing assistance payment.

    Science.gov (United States)

    2010-04-01

    ... Special Housing Types Shared Housing § 982.617 Shared housing: Rent and voucher housing assistance payment... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Shared housing: Rent and voucher housing assistance payment. 982.617 Section 982.617 Housing and Urban Development Regulations Relating to...

  20. Assisted Housing - Public Housing Authorities - National Geospatial Data Asset (NGDA)

    Data.gov (United States)

    Department of Housing and Urban Development — Public Housing was established to provide decent and safe rental housing for eligible low-income families, the elderly, and persons with disabilities. Public housing...

  1. Investigation of load leveling in Hokuriku Electric Power Co., Inc.; Hokuriku denryoku no fuka heijunka eno torikumi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    Hokuriku Electric Power Co., Inc. aims at an around 2% improvement of the load factor up to 2005, by which the quick and proper service and the proposal of load leveling menu are planned. This paper describes an outline of the investigation of load leveling. Various programs have been proposed so that the customers can further shift the load by their consideration. Proposed systems include the time-of-day electricity rate system, the load regulation contract system for industries, the seasonal time-of-day rate system, the electric power system for snowmelt in which the load is dumped at the peak, and the secondary electric power system for snowmelt. Accompanying with the revision of electric utility law, the enlargement of its available time, the price reduction, and the discount rate system for the ice regenerative air conditioners have been provided. For the business activities, a demonstration model house was exhibited to indicate a proper house with local characteristics in Hokuriku district. Furthermore, the spreading activities of regenerative systems and the consulting activities have been positively promoted. 4 figs., 1 tab.

  2. Media Presentation Mode, English Listening Comprehension and Cognitive Load in Ubiquitous Learning Environments: Modality Effect or Redundancy Effect?

    Science.gov (United States)

    Chang, Chi-Cheng; Lei, Hao; Tseng, Ju-Shih

    2011-01-01

    Although ubiquitous learning enhances students' access to learning materials, it is crucial to find out which media presentation modes produce the best results for English listening comprehension. The present study examined the effect of media presentation mode (sound and text versus sound) on English listening comprehension and cognitive load.…

  3. Housing culture

    DEFF Research Database (Denmark)

    Roesdahl, Else; Scholkmann, Barbara

    2007-01-01

    On houses and their furniture and fittings, and on the study of this - with a comparison of rural, urban, monastic and aristocratic housing, and a special section on heating technologies.......On houses and their furniture and fittings, and on the study of this - with a comparison of rural, urban, monastic and aristocratic housing, and a special section on heating technologies....

  4. Comparative Study of Phase Transformation in Single-Crystal Germanium during Single and Cyclic Nanoindentation

    Directory of Open Access Journals (Sweden)

    Koji Kosai

    2017-11-01

    Full Text Available Single-crystal germanium is a semiconductor material which shows complicated phase transformation under high pressure. In this study, new insight into the phase transformation of diamond-cubic germanium (dc-Ge was attempted by controlled cyclic nanoindentation combined with Raman spectroscopic analysis. Phase transformation from dc-Ge to rhombohedral phase (r8-Ge was experimentally confirmed for both single and cyclic nanoindentation under high loading/unloading rates. However, compared to single indentation, double cyclic indentation with a low holding load between the cycles caused more frequent phase transformation events. Double cyclic indentation caused more stress in Ge than single indentation and increased the possibility of phase transformation. With increase in the holding load, the number of phase transformation events decreased and finally became less than that under single indentation. This phenomenon was possibly caused by defect nucleation and shear accumulation during the holding process, which were promoted by a high holding load. The defect nucleation suppressed the phase transformation from dc-Ge to r8-Ge, and shear accumulation led to another phase transformation pathway, respectively. A high holding load promoted these two phenomena, and thus decreased the possibility of phase transformation from dc-Ge to r8-Ge.

  5. Determinants of manganese levels in house dust samples from the CHAMACOS cohort

    Energy Technology Data Exchange (ETDEWEB)

    Gunier, R.B., E-mail: gunier@berkeley.edu [Center for Environmental Research and Children’s Health (CERCH), School of Public Health, University of California, Berkeley, CA (United States); Jerrett, M. [Center for Environmental Research and Children’s Health (CERCH), School of Public Health, University of California, Berkeley, CA (United States); Smith, D.R.; Jursa, T. [Microbiology and Environmental Toxicology, University of California, Santa Cruz, CA (United States); Yousefi, P.; Camacho, J.; Hubbard, A.; Eskenazi, B.; Bradman, A. [Center for Environmental Research and Children’s Health (CERCH), School of Public Health, University of California, Berkeley, CA (United States)

    2014-11-01

    Introduction: Manganese (Mn) is an essential nutrient, but at high exposure levels Mn is a neurotoxicant. The fungicides maneb and mancozeb are approximately 21% Mn by weight and more than 150,000 kg are applied each year to crops in the Salinas Valley, California. It is not clear, however, whether agricultural use of these fungicides increases Mn levels in homes. Materials and methods: We collected house dust samples from 378 residences enrolled in the Center for the Health Assessment of Mothers and Children of Salinas (CHAMACOS) study with a second sample collected approximately nine months later from 90 of the residences. House dust samples were analyzed for Mn using inductively coupled plasma optical emission spectroscopy. Information from interviews, home inspections, and pesticide use reports was used to identify potential predictors of Mn dust concentrations and loadings. Results: Mn was detectable in all dust samples. The median Mn concentration was 171 μg/g and median Mn loading was 1,910 μg/m{sup 2} at first visit. In multivariable models, Mn dust concentrations and loadings increased with the number of farmworkers in the home and the amount of agricultural Mn fungicides applied within three kilometers of the residence during the month prior to dust sample collection. Dust concentrations of Mn and other metals (lead, cadmium and chromium) were higher in residences located in the southern Salinas Valley compared those located in other areas of the Salinas Valley. Dust loadings of Mn and other metals were also higher in residences located on Antioch Loam soil than other soil types, and in homes with poor or average housekeeping practices. Conclusions: Agricultural use of Mn containing fungicides was associated with Mn dust concentrations and loadings in nearby residences and farmworker homes. Housekeeping practices and soil type at residence were also important factors related to dust metal concentrations and loadings. - Highlights: • Manganese dust

  6. Deformation analysis of rotary combustion engine housings

    Science.gov (United States)

    Vilmann, Carl

    1991-01-01

    This analysis of the deformation of rotary combustion engine housings targeted the following objectives: (1) the development and verification of a finite element model of the trochoid housing, (2) the prediction of the stress and deformation fields present within the trochoid housing during operating conditions, and (3) the development of a specialized preprocessor which would shorten the time necessary for mesh generation of a trochoid housing's FEM model from roughly one month to approximately two man hours. Executable finite element models were developed for both the Mazda and the Outboard Marine Corporation trochoid housings. It was also demonstrated that a preprocessor which would hasten the generation of finite element models of a rotary engine was possible to develop. The above objectives are treated in detail in the attached appendices. The first deals with finite element modeling of a Wankel engine center housing, and the second with the development of a preprocessor that generates finite element models of rotary combustion engine center housings. A computer program, designed to generate finite element models of user defined rotary combustion engine center housing geometries, is also included.

  7. AN EXACT ELASTO-PLASTIC SOLUTION OF METAL-MATRIX COMPOSITE CANTILEVER BEAM LOADED BY A SINGLE FORCE AT ITS FREE END

    Directory of Open Access Journals (Sweden)

    Onur SAYMAN

    2001-03-01

    Full Text Available In the present study, an elastic-plastic stress analysis is carried out in a metal matrix composite cantilever beam loaded by a single force at its free end. A composite consisting of stainless-steel reinforced aluminium was produced for this work. The orientation angle of the fibers is chosen as 0°, 30°, 45°, 60° and 90°. The material is assumed to be perfectly plastic in the elasto-plastic solution. An analytical solution is performed for satisfying both the governing differential equation in the plane stress case and boundary conditions for small plastic deformations. The solution is carried out under the assumption of the Bernoulli-Navier hypotheses. The composite material is assumed as hardening linearly. The Tsai-Hill theory is used as a yield criterion.

  8. Changing distribution and geometry of S′ in Al–Cu–Mg single crystals during stress aging by controlling the loading orientation

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Jiqiang [School of Material Science and Engineering, Central South University, Yuelu Section, Changsha, Hunan 410083 (China); Chen, Zhiguo [School of Material Science and Engineering, Central South University, Yuelu Section, Changsha, Hunan 410083 (China); Hunan University of Humanities, Science and Technology, Loudi 417000 (China); Guo, Xiaobin [School of Material Science and Engineering, Central South University, Yuelu Section, Changsha, Hunan 410083 (China); Deng, Yunlai, E-mail: luckdeng@csu.edu.cn [School of Material Science and Engineering, Central South University, Yuelu Section, Changsha, Hunan 410083 (China); State Key Laboratory of High Performance and Complex Manufacturing, Central South University, Changsha 410083 (China)

    2016-01-05

    The precipitation behavior of S′ phase in Al–Cu–Mg single crystals during stress-free and stress aging was investigated by transmission electron microscopy (TEM). Different compressive stress magnitudes and loading orientations were applied to determine their effects on the precipitation of S′ in Al–Cu–Mg alloy during stress aging. The results indicate that a noticeable preferential orientation of S′ is generated in the sample under applied compressive stress of 33 MPa loading along close to [001]{sub Al}, whilst no obviously preferential orientation of S′ can be observed in the sample loaded along close to [101]{sub Al} under the same applied stress or even larger applied stress. The precipitation distribution of S′ phase during stress aging can be changed by the loading orientation of the applied stress. Moreover, compressive stress aging may lead to S′ phase shorter in length, and the length of S′ phase shows a decreasing tendency with increasing applied stress, which are associated with the positive misfit between S′ and Al matrix.

  9. Short term load forecasting: two stage modelling

    Directory of Open Access Journals (Sweden)

    SOARES, L. J.

    2009-06-01

    Full Text Available This paper studies the hourly electricity load demand in the area covered by a utility situated in the Seattle, USA, called Puget Sound Power and Light Company. Our proposal is put into proof with the famous dataset from this company. We propose a stochastic model which employs ANN (Artificial Neural Networks to model short-run dynamics and the dependence among adjacent hours. The model proposed treats each hour's load separately as individual single series. This approach avoids modeling the intricate intra-day pattern (load profile displayed by the load, which varies throughout days of the week and seasons. The forecasting performance of the model is evaluated in similiar mode a TLSAR (Two-Level Seasonal Autoregressive model proposed by Soares (2003 using the years of 1995 and 1996 as the holdout sample. Moreover, we conclude that non linearity is present in some series of these data. The model results are analyzed. The experiment shows that our tool can be used to produce load forecasting in tropical climate places.

  10. Cortical activities of single-trial P300 amplitudes modulated by memory load using simultaneous EEG-fMRI

    Science.gov (United States)

    Zhang, Qiushi; Zhao, Xiaojie; Zhu, Chaozhe; Yang, Xueqian; Yao, Li

    2015-03-01

    The functional magnetic resonance imaging (fMRI) researches on working memory have found that activation of cortical areas appeared dependent on memory load, and event-related potentials (ERP) studies have demonstrated that amplitudes of P300 decreased significantly when working memory load increased. However, the cortical activities related with P300 amplitudes under different memory loads remains unclear. Joint fMRI and EEG analysis which fusions the time and spatial information in simultaneous EEG-fMRI recording can reveal the regional activation at each ERP time point. In this paper, we first used wavelet transform to obtain the single-trial amplitudes of P300 caused by a digital N-back task in the simultaneous EEG-fMRI recording as the ERP feature sequences. Then the feature sequences in 1-back condition and 3-back condition were introduced into general linear model (GLM) separately as parametric modulations to compare the cortical activation under different memory loads. The results showed that the average amplitudes of P300 in 3-back significantly decreased than that in 1-back, and the activities induced by ERP feature sequences in 3-back also significantly decreased than that in the 1-back, including the insular, anterior cingulate cortex, right inferior frontal gyrus, and medial frontal gyrus, which were relevant to the storage, monitoring, and manipulation of information in working memory task. Moreover, the difference in the activation caused by ERP feature showed a positive correlation with the difference in behavioral performance. These findings demonstrated the locations of P300 amplitudes differences modulated by the memory load and its relationship with the behavioral performance.

  11. APPLICATION OF AUGMENTED REALITY IN FACADE REDESIGN PRESENTATION

    Directory of Open Access Journals (Sweden)

    PEJIĆ Petar

    2015-06-01

    Full Text Available Augmented Reality (AR is a computer technology where the perception of the user is enhanced by the seamless blending between real environment and computer-generated virtual objects coexisting in the same space. When it comes to a redesign of the existing facades, it is necessary to create a visual presentation of the proposed changes. For this reason, contemporary architectural approach assumes creating a digital 3D model of the newly designed facade. Since the façade redesign is a real world change, the AR can be used for newly designed facade project presentation. In this paper a case study of the AR application for façade redesign presentation of a single family house located in Babušnica (Serbia is presented.

  12. Modern Housing Retrofit: Assessment of Upgrade Packages to EnerPHit Standard for 1940–1960 State Houses in Auckland

    OpenAIRE

    Paola Leardini; Manfredo Manfredini

    2015-01-01

    New Zealand state housing includes a significant portion of problematic buildings constructed after the public housing scheme launched in 1936. Most of these houses are still uninsulated, thus, cold, draughty, mouldy, and progressively decaying; however, as they are fundamental elements of the country’s culture, society, and environment, and are built with good quality materials and sound construction, they are suitable candidates for effective energy upgrades. This paper presents findings of...

  13. An energy estimation framework for event-based methods in Non-Intrusive Load Monitoring

    International Nuclear Information System (INIS)

    Giri, Suman; Bergés, Mario

    2015-01-01

    Highlights: • Energy estimation is NILM has not yet accounted for complexity of appliance models. • We present a data-driven framework for appliance modeling in supervised NILM. • We test the framework on 3 houses and report average accuracies of 5.9–22.4%. • Appliance models facilitate the estimation of energy consumed by the appliance. - Abstract: Non-Intrusive Load Monitoring (NILM) is a set of techniques used to estimate the electricity consumed by individual appliances in a building from measurements of the total electrical consumption. Most commonly, NILM works by first attributing any significant change in the total power consumption (also known as an event) to a specific load and subsequently using these attributions (i.e. the labels for the events) to estimate energy for each load. For this last step, most published work in the field makes simplifying assumptions to make the problem more tractable. In this paper, we present a framework for creating appliance models based on classification labels and aggregate power measurements that can help to relax many of these assumptions. Our framework automatically builds models for appliances to perform energy estimation. The model relies on feature extraction, clustering via affinity propagation, perturbation of extracted states to ensure that they mimic appliance behavior, creation of finite state models, correction of any errors in classification that might violate the model, and estimation of energy based on corrected labels. We evaluate our framework on 3 houses from standard datasets in the field and show that the framework can learn data-driven models based on event labels and use that to estimate energy with lower error margins (e.g., 1.1–42.3%) than when using the heuristic models used by others

  14. Influence of Housing System and Number of Transported Animals on Transport-induced Mortality in Slaughter Pigs

    Directory of Open Access Journals (Sweden)

    Eva Voslářová

    2010-01-01

    Full Text Available The study monitored the effect of the housing system and the number of animals transported together on transport-induced mortality of slaughter pigs in the Czech Republic in the period from 2004 to 2008. Concerning the type of housing during the fattening, the lowest mortality rate during the subsequent transport to slaughter houses was detected among pigs fattened on solid floor (0.047% and on deep bedding (0.084%. The highest mortality during transport was detected among pigs fattened on fully or partially slatted floor (0.139%, a significant difference (p p < 0.01 compared to the load sizes of up to 40 animals.

  15. Low energy houses and passive houses - common questions; Laagenergihus och passivhus - vanliga fraagestaellningar

    Energy Technology Data Exchange (ETDEWEB)

    Sikander, Eva; Samuelson, Ingemar; Gustavsson, Thorbjoern; Ruud, Svein; Larsson, Krister; Hiller, Carolina; Werner, Goesta; Gabrielii, Kristina

    2009-07-01

    This feasibility study of passive houses and low-energy houses has raised several questions concerning aspects of which more knowledge is needed. Many can be answered by existing knowledge, but there are still several that can only partly be answered, and some that cannot be answered at all. As there is a substantial demand for, and interest in, the construction of low-energy houses and passive houses, it is important that the remaining questions should be addressed so that the building sector can continue to develop. Examples of areas where further knowledge is needed include: moisture safe and energy-efficient building envelopes; demand-responsive ventilation, without risk of poor indoor environmental conditions; thermal comfort (summer and winter); airtight and durable detailing; design systems and working methods to ensure retention of good characteristics when converting or extending buildings; durability aspects of certain components and functions; the effects of occupants on energy use; how indoor environment conditions and functions will cope with climate change; quality assurance in order to ensure that the appropriate knowledge is applied, and that the work is carried out properly. Some important points to emphasise: The design and construction of low-energy houses and passive houses must be firmly based on the correct design principles and appropriate standards of workmanship, in order to ensure that the houses are energy-efficient, have good indoor environmental conditions and can be expected to have long lives. Proper understanding of the principles, coupled with constant quality awareness, are essential in all stages of the work from the developer, designer and construction personnel but also during operation-phase. Hitherto, low-energy houses and passive houses have been built in relatively small numbers, but the expectation is that interest in them will increase. This raises the question of how, if production is to be very much more than at present

  16. Caisson structures in the Beaufort Sea 1982-1990 : characteristics, instrumentation and ice loads

    Energy Technology Data Exchange (ETDEWEB)

    Timco, G.W.; Johnston, M.E. [National Research Council of Canada, Ottawa, ON (Canada). Canadian Hydraulics Centre

    2002-11-01

    This report presents a comprehensive overview of the instrumentation, characteristics and measured ice loads on the caisson structures used for exploratory drilling in the Canadian Beaufort Sea during the 1970s and 1980s. The focus was placed on the Tarsiut Caissons, the Single Steel Drilling Caisson (SSDC), the Caisson Retained Island (CRI), and the Molikpaq. Details on the ice-load measuring instrumentation were provided for each of the drill sites featuring an ice-load measurement program. The results of global loads on the structures were presented as a Line Load (global load per width of the structure) and the Global Pressure (line load per ice thickness). The authors showed that global loads were a function of the ice macrostructure (level first-year sea ice, multi-year ice, first-year ridges, hummock fields, isolated floes). A general increase in the Line Load with increasing ice thickness was revealed through analysis. There was considerable scatter in the data, and the authors explained it by examining the failure mode of the ice during the interaction process. 36 refs., 4 tabs., 57 figs.

  17. Single house on-site grey water treatment using a submerged membrane bioreactor for toilet flushing.

    Science.gov (United States)

    Fountoulakis, M S; Markakis, N; Petousi, I; Manios, T

    2016-05-01

    Wastewater recycling has been and continues to be practiced all over the world for a variety of reasons including: increasing water availability, combating water shortages and drought, and supporting environmental and public health protection. Nowadays, one of the most interesting issues for wastewater recycling is the on-site treatment and reuse of grey water. During this study the efficiency of a compact Submerged Membrane Bioreactor (SMBR) system to treat real grey water in a single house in Crete, Greece, was examined. In the study, grey water was collected from a bathtub, shower and washing machine containing significant amounts of organic matter and pathogens. Chemical oxygen demand (COD) removal in the system was approximately 87%. Total suspended solids (TSS) were reduced from 95mgL(-1) in the influent to 8mgL(-1) in the effluent. The efficiency of the system to reduce anionic surfactants was about 80%. Fecal and total coliforms decreased significantly using the SMBR system due to rejection, by the membrane, used in the study. Overall, the SMBR treatment produces average effluent values that would satisfy international guidelines for indoor reuse applications such as toilet flushing. Copyright © 2016 Elsevier B.V. All rights reserved.

  18. 24 CFR 982.606 - Congregate housing: Who may reside in congregate housing.

    Science.gov (United States)

    2010-04-01

    ... Special Housing Types Congregate Housing § 982.606 Congregate housing: Who may reside in congregate housing. (a) An elderly person or a person with disabilities may reside in a congregate housing unit. (b... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Congregate housing: Who may reside...

  19. An Object-Based Classification Approach for Mapping Migrant Housing in the Mega-Urban Area of the Pearl River Delta (China

    Directory of Open Access Journals (Sweden)

    Sebastian D’Oleire-Oltmanns

    2011-08-01

    Full Text Available Urban areas develop on formal and informal levels. Informal development is often highly dynamic, leading to a lag of spatial information about urban structure types. In this work, an object-based remote sensing approach will be presented to map the migrant housing urban structure type in the Pearl River Delta, China. SPOT5 data were utilized for the classification (auxiliary data, particularly up-to-date cadastral data, were not available. A hierarchically structured classification process was used to create (spectral independence from single satellite scenes and to arrive at a transferrable classification process. Using the presented classification approach, an overall classification accuracy of migrant housing of 68.0% is attained.

  20. Mass Housing and Changings in Housing Demand, Case of Diyarbakir, Turkey

    OpenAIRE

    M. Oguz Sinemillioglu; Can Tuncay Akın; Havva Özyılmaz

    2005-01-01

    The aim of this study is to analyze changings in housing demand, especially in term of house size in Diyarbakır case, in Turkey. Though Housing in Turkey is in a free market system, there is a Mass Housing Administration (TOKÃ ) has been doing mass houses for, relatively, middle class income people. Diyarbakır, one of the cities that TOKÃ has done two thousand houses, has taken too much migration, so that the demand in housing form and structure has different alterations. This process should ...

  1. Pervasive within-Mitochondrion Single-Nucleotide Variant Heteroplasmy as Revealed by Single-Mitochondrion Sequencing

    Directory of Open Access Journals (Sweden)

    Jacqueline Morris

    2017-12-01

    Full Text Available Summary: A number of mitochondrial diseases arise from single-nucleotide variant (SNV accumulation in multiple mitochondria. Here, we present a method for identification of variants present at the single-mitochondrion level in individual mouse and human neuronal cells, allowing for extremely high-resolution study of mitochondrial mutation dynamics. We identified extensive heteroplasmy between individual mitochondrion, along with three high-confidence variants in mouse and one in human that were present in multiple mitochondria across cells. The pattern of variation revealed by single-mitochondrion data shows surprisingly pervasive levels of heteroplasmy in inbred mice. Distribution of SNV loci suggests inheritance of variants across generations, resulting in Poisson jackpot lines with large SNV load. Comparison of human and mouse variants suggests that the two species might employ distinct modes of somatic segregation. Single-mitochondrion resolution revealed mitochondria mutational dynamics that we hypothesize to affect risk probabilities for mutations reaching disease thresholds. : Morris et al. use independent sequencing of multiple individual mitochondria from mouse and human brain cells to show high pervasiveness of mutations. The mutations are heteroplasmic within single mitochondria and within and between cells. These findings suggest mechanisms by which mutations accumulate over time, resulting in mitochondrial dysfunction and disease. Keywords: single mitochondrion, single cell, human neuron, mouse neuron, single-nucleotide variation

  2. CDBG Housing Activity

    Data.gov (United States)

    Department of Housing and Urban Development — CDBG activity related to housing, including multifamily rehab, housing services, code enforcement, operation and repair of foreclosed property and public housing...

  3. Climatization, energy and design in rural housing

    International Nuclear Information System (INIS)

    Aroztegui, J.

    1994-01-01

    The Work analyzes the possibilities to influence in the energy inputs of the air conditioning in the rural housing through architectonic project decisions. It presents a methodology to guide the first project decisions and to evaluate the future of the housing behavior

  4. Morphological operation based dense houses extraction from DSM

    OpenAIRE

    Li, Y.; Zhu, L.; Tachibana, K.; Shimamura, H.

    2014-01-01

    This paper presents a method of reshaping and extraction of markers and masks of the dense houses from the DSM based on mathematical morphology (MM). Houses in a digital surface model (DSM) are almost joined together in high-density housing areas, and most segmentation methods cannot completely separate them. We propose to label the markers of the buildings firstly and segment them into masks by watershed then. To avoid detecting more than one marker for a house or no marker at all d...

  5. The Effects of Presentation Method and Information Density on Visual Search Ability and Working Memory Load

    Science.gov (United States)

    Chang, Ting-Wen; Kinshuk; Chen, Nian-Shing; Yu, Pao-Ta

    2012-01-01

    This study investigates the effects of successive and simultaneous information presentation methods on learner's visual search ability and working memory load for different information densities. Since the processing of information in the brain depends on the capacity of visual short-term memory (VSTM), the limited information processing capacity…

  6. Reasons for increasing radon concentrations in radon remediated houses

    International Nuclear Information System (INIS)

    Clavensjoe, B.

    1997-01-01

    The study comprises 31 single-dwelling houses where remedial actions were carried out in the 1980s. In all of them the radon concentrations have increased more than 30% according to recent control measurements. Radon sources are building material as well as the soil. The remedial actions dealt with ventilation systems, leakage through the basement floor, air cushions, sub-slab suction or radon wells according to the original problems. Causes for the increase varied: In many houses with soil radon problems, the installation of a normal mechanical ventilation system is not a good remedial action. In some houses on a ground with high permeability and high radon content in the soil air, the radon concentration may increase by the lowering of the indoor air pressure. In other houses the increase was a measurement effect, where sites/rooms were confused. Living related causes were identified in a number of cases, where fan speeds were reduced for energy conservation/noise reduction purposes or different use of windows airing had occurred. Extension of the dwelling space without changing the ventilation system caused the increase in one house. 23 refs

  7. Multi-port network and 3D finite-element models for accurate transformer calculations: Single-phase load-loss test

    Energy Technology Data Exchange (ETDEWEB)

    Escarela-Perez, R. [Departamento de Energia, Universidad Autonoma Metropolitana, Av. San Pablo 180, Col. Reynosa, C.P. 02200, Mexico D.F. (Mexico); Kulkarni, S.V. [Electrical Engineering Department, Indian Institute of Technology, Bombay (India); Melgoza, E. [Instituto Tecnologico de Morelia, Av. Tecnologico 1500, Morelia, Mich., C.P. 58120 (Mexico)

    2008-11-15

    A six-port impedance network for a three-phase transformer is obtained from a 3D time-harmonic finite-element (FE) model. The network model properly captures the eddy current effects of the transformer tank and frame. All theorems and tools of passive linear networks can be used with the multi-port model to simulate several important operating conditions without resorting anymore to computationally expensive 3D FE simulations. The results of the network model are of the same quality as those produced by the FE program. Although the passive network may seem limited by the assumption of linearity, many important transformer operating conditions imply unsaturated states. Single-phase load-loss measurements are employed to demonstrate the effectiveness of the network model and to understand phenomena that could not be explained with conventional equivalent circuits. In addition, formal deduction of novel closed-form formulae is presented for the calculation of the leakage impedance measured at the high and low voltage sides of the transformer. (author)

  8. Assessment of housing design decisions in informal housing ...

    African Journals Online (AJOL)

    The rapid urbanisation of cities in developing countries has witnessed a growth in the volume of housing construction in the urban areas. The demand for housing and the inability of government to meet this demand has encouraged the growth of informal housing. The concept of healthy buildings is of great importance, ...

  9. Present knowledge about Laboratory Testing of Axial Loading on Suction Caissons

    DEFF Research Database (Denmark)

    Manzotti, E.; Vaitkunaite, Evelina; Ibsen, Lars Bo

    Offshore wind turbines are increasing in both efficiency and size. More economical foundations for such light structures are under investigation, and suction caisson was shown to be particularly suitable for this purpose. In multi-pod foundation configuration, the overturning moment given by loads...... on the structure is resisted by push-pull loads on the vertical axis of each suction caisson. Relevant works where this situation is examined by means of laboratory testing are summarized in this article, then different conclusions are followed by discussion and comparison. In the initial theoretical section...

  10. Evaluation of a cost effective in-house method for HIV-1 drug resistance genotyping using plasma samples.

    Directory of Open Access Journals (Sweden)

    Devidas N Chaturbhuj

    Full Text Available OBJECTIVES: Validation of a cost effective in-house method for HIV-1 drug resistance genotyping using plasma samples. DESIGN: The validation includes the establishment of analytical performance characteristics such as accuracy, reproducibility, precision and sensitivity. METHODS: The accuracy was assessed by comparing 26 paired Virological Quality Assessment (VQA proficiency testing panel sequences generated by in-house and ViroSeq Genotyping System 2.0 (Celera Diagnostics, US as a gold standard. The reproducibility and precision were carried out on five samples with five replicates representing multiple HIV-1 subtypes (A, B, C and resistance patterns. The amplification sensitivity was evaluated on HIV-1 positive plasma samples (n = 88 with known viral loads ranges from 1000-1.8 million RNA copies/ml. RESULTS: Comparison of the nucleotide sequences generated by ViroSeq and in-house method showed 99.41±0.46 and 99.68±0.35% mean nucleotide and amino acid identity respectively. Out of 135 Stanford HIVdb listed HIV-1 drug resistance mutations, partial discordance was observed at 15 positions and complete discordance was absent. The reproducibility and precision study showed high nucleotide sequence identities i.e. 99.88±0.10 and 99.82±0.20 respectively. The in-house method showed 100% analytical sensitivity on the samples with HIV-1 viral load >1000 RNA copies/ml. The cost of running the in-house method is only 50% of that for ViroSeq method (112$ vs 300$, thus making it cost effective. CONCLUSIONS: The validated cost effective in-house method may be used to collect surveillance data on the emergence and transmission of HIV-1 drug resistance in resource limited countries. Moreover, the wide applications of a cost effective and validated in-house method for HIV-1 drug resistance testing will facilitate the decision making for the appropriate management of HIV infected patients.

  11. Stress and fatigue analysis of fuelling machine housing of 500 MWe PHWR

    International Nuclear Information System (INIS)

    Dutta, B.K.; Ramana, W.V.; Kushwaha, H.S.; Kakodkar, A.

    1987-01-01

    One of the most appealing features of the Pressurised Heavy Water Reactors is the online refuelling capability. For this a fuelling machine is used. This machine opens a reactor channel by removing a seal plug and a shield plug and then does the necessary fuelling by pushing fuel bundles from a fuel magazine by rams. After necessary fuelling the machine closes the channel automatically. One of the most important parts of the fuelling machine is its pressure housing which becomes a part of the reactor channel during refuelling operation. It houses the fuel magazine, separators and rams. Beside channel pressure and other mechanical loads, the pressure housing experiences thermal transients during refuelling. The housing consists of two cylindrical shells having one end-closer in each. They are connected with each other by a large sized coupling. There are many holes on both the end-closers to accommodate ram movement, separators and magazine rive mechanisms. Some of these holes intersect with each other in the housing end-closers and hence end-closers are reinforced accordingly. This also makes the end-closers nonsymmetric. In the following sections the various analysis done to compute general stress distribution, stress concentration factors near to various holes, temperature transients during refuelling and also allowable fatigue cycles for pressure housing of fuelling machine for the proposed 500 MWe are described. (orig.)

  12. Stress and fatigue analysis of fuelling machine housing of 500 MWe PHWR

    International Nuclear Information System (INIS)

    Dutta, B.K.; Ramana, W.V.; Kushwaha, H.S.; Kakodkar, A.

    1987-01-01

    One of the most appealing features of the Pressurised Heavy Water Reactors is the online refuelling capability. For this a fuelling machine is used. This machine opens a reactor channel by removing a seal plug and a shield plug and then does the necessary fuelling by pushing fuel bundles from a fuel magazine by rams. After necessary fuelling the machine closes the channel automatically. One of the most important parts of the fuelling machine is its pressure housing which becomes a part of the reactor channel during refuelling operation. It houses the fuel magazine, separators and rams. Beside channel pressure and other mechanical loads, the pressure housing experiences thermal transients during refuelling. The housing consists of two cylindrical shells having one end-closer in each. They are connected with each other by a large sized coupling. There are many holes on both the end-closers to accommodate ram movement, separators and magazine drive mechanisms. Some of these holes intersect with each other in the housing end-closures and hence end-closures are reinforced accordingly. This also makes the end-closures nonsymmetric. In the following sections the various analysis done to compute general stress distribution, stress concentration factors near to various holes, temperature transients during refuelling and also allowable fatigue cycles for pressure housing of fuelling machine for the proposed 500 MWe are described

  13. 7 CFR 1955.112 - Method of sale (housing).

    Science.gov (United States)

    2010-01-01

    .... Adequate and timely advertising in accordance with § 1955.146 of this subpart is of utmost importance when... Director will request such authorization when all reasonable marketing efforts fail to produce buyers and... documentation of all marketing efforts, will be forwarded to the Assistant Administrator, Housing, ATTN: Single...

  14. 24 CFR 8.25 - Public housing and multi-family Indian housing.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Public housing and multi-family Indian housing. 8.25 Section 8.25 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development NONDISCRIMINATION BASED ON HANDICAP IN FEDERALLY ASSISTED PROGRAMS AND...

  15. Sustained housing-type social buffering following social housing in male rats.

    Science.gov (United States)

    Kiyokawa, Yasushi; Ishida, Aya; Takeuchi, Yukari; Mori, Yuji

    2016-05-01

    In social animals, recovery from the adverse effects of distressing stimuli is promoted by subsequent cohousing with a conspecific animal(s). This phenomenon has been termed housing-type social buffering. We previously found that social housing induced housing-type social buffering in fear-conditioned male rats. This buffering took the form of attenuated conditioned hyperthermia in response to an auditory conditioned stimulus (CS). Here, we assessed whether this social buffering is sustained even if the subject is housed alone after a period of social housing. When fear-conditioned subjects were housed alone during a 48-h period between conditioning and re-exposure to the auditory CS, they exhibited conditioned hyperthermia in response to the CS. However, conditioned hyperthermia was not observed when the 12-h period of social housing began 24 and 36h after conditioning during the 48-h period. This was not the case when the 12-h period of social housing began 0 and 12h after the conditioning. These results suggest that housing-type social buffering is sustained for 12h after the 12-h period of social housing. We next considered whether increasing the duration of social housing would extend the period of social buffering. We observed social buffering of conditioned hyperthermia 24 and 48, but not 96h after a 24-h period of social housing. These results suggest that social buffering was extended when the duration of social housing was increased. Taken together, our findings indicate that housing-type social buffering is sustained after a period of social housing. Copyright © 2016 Elsevier Inc. All rights reserved.

  16. Social and structural barriers to housing among street-involved youth who use illicit drugs.

    Science.gov (United States)

    Krüsi, Andrea; Fast, Danya; Small, Will; Wood, Evan; Kerr, Thomas

    2010-05-01

    In Canada, approximately 150,000 youth live on the street. Street-involvement and homelessness have been associated with various health risks, including increased substance use, blood-borne infections and sexually transmitted diseases. We undertook a qualitative study to better understand the social and structural barriers street-involved youth who use illicit drugs encounter when seeking housing. We conducted 38 semi-structured interviews with street-involved youth in Vancouver, Canada from May to October 2008. Interviewees were recruited from the At-risk Youth Study (ARYS) cohort, which follows youth aged 14 to 26 who have experience with illicit drug use. All interviews were thematically analyzed, with particular emphasis on participants' perspectives regarding their housing situation and their experiences seeking housing. Many street-involved youth reported feeling unsupported in their efforts to find housing. For the majority of youth, existing abstinence-focused shelters did not constitute a viable option and, as a result, many felt excluded from these facilities. Many youth identified inflexible shelter rules and a lack of privacy as outweighing the benefits of sleeping indoors. Single-room occupancy hotels (SROs) were reported to be the only affordable housing options, as many landlords would not rent to youth on welfare. Many youth reported resisting moving to SROs as they viewed them as unsafe and as giving up hope for a return to mainstream society. The findings of the present study shed light on the social and structural barriers street-involved youth face in attaining housing and challenge the popular view of youth homelessness constituting a lifestyle choice. Our findings point to the need for housing strategies that include safe, low threshold, harm reduction focused housing options for youth who engage in illicit substance use.

  17. Si-coated single-walled carbon nanotubes under axial loads: An atomistic simulation study

    International Nuclear Information System (INIS)

    Song Haiyang; Zha Xinwei

    2007-01-01

    The mechanical properties of the Si-coated imperfect (5, 5) single-walled carbon nanotube (SWCNT), the imperfect (5, 5) SWCNT and several perfect armchair SWCNTs under axial loads were investigated using molecular dynamics simulation. The interactions between atoms were modeled using the empirical Tersoff potential and the Tersoff-Brenner potential coupled with the Lennard-Jones potential. We get Young's modulus of the defective (5, 5) nanotube with and without the Si coating under axial tension 1107.92 and 1076.02 GPa, respectively. The results also show that the structure failure of the Si-coated imperfect (5, 5) SWCNT under axial compression occurs at a slightly higher strain than for the perfect (5, 5) SWCNT. Therefore, we can confirm the protective effect of Si as a coating material for defective SWCNTs. We also obtain the critical buckling strains of perfect SWCNTs

  18. OL1/OL2 License renewal for extended life-time: Class 1 piping load and strength analyses

    International Nuclear Information System (INIS)

    Lemettinen, P.

    2015-01-01

    Teollisuuden Voima Oyj (TVO) operates two NPP units Olkiluoto 1 (OL1) and Olkiluoto 2 (OL2), that are identical 880 MWe BWRs. The units were originally designed for 40 years life-time. TVO is applying license renewal for extended life-time for 60 years plant life. Part of the license renewal project is to evaluate and update all Class 1 piping load and strength analyses. These analyses are done with the help of TVO's in-house Piping and Component Analysis and Monitoring System (PAMS). PAMS is basically a database system, consisting of separate geometry, material, loading, result and document databases. The thermo hydraulic analysis program RELAP5 is used to obtain temperature, pressure and mass flow for the piping loading areas. The piping strength analysis are carried out mainly with the Finnish FPIPE FEA program for all related thermal transient and dynamic load cases. The slides of the presentation have been added to the paper

  19. Satisfaction with housing and housing support for people with psychiatric disabilities.

    Science.gov (United States)

    Brolin, Rosita; Rask, Mikael; Syrén, Susanne; Baigi, Amir; Brunt, David Arthur

    2015-01-01

    The aim of this study was to investigate the degree of satisfaction with housing and housing support for people with psychiatric disabilities in Sweden. A total of 370 residents, in supported housing and in ordinary housing with housing support, completed a new questionnaire and reported a high degree of overall satisfaction, but many of them wanted to move somewhere else. Differences were found between the two different types of housing concerning satisfaction with housing support, social life and available choices. Security and privacy, as well as other's influence on the choice of residential area and dwelling proved to be important predictors for satisfaction.

  20. Load Assembly Design of the FAST Machine

    International Nuclear Information System (INIS)

    Cucchiaro, A.; Albanese, R.; Ambrosino, G.; Brolatti, G.; Calabro, G.; Cocilovo, V.; Coletti, A.; Coletti, R.; Costa, P.; Frosi, P.; Crescenzi, F.; Crisanti, F.; Granucci, G.; Maddaluno, G.; Pericoli Ridolfini, V.; Pizzuto, A.; Rita, C.; Ramogida, G.

    2008-01-01

    The FAST [1][2] (Fusion Advanced Studies Torus) load assembly, which includes the Vacuum Vessel (VV) and its internal components, the magnet system and the poloidal field coils, is presented in this paper. FAST operates at a wide range [3][4] of parameters from high performance H-Mode (B T up to 8.5 T; I P up to 8 MA) as well as Advance Tokamak operation (I P =3 MA), and full non inductive current scenario (I P =2 MA). Helium gas at 30K is used for cooling the resistive copper magnets. That allows for a pulse duration up to 170 s (∼ 40 times τres) at 3MA/ 3.5T. To limit the TF magnet ripple ferromagnetic within acceptable values insert have been introduced inside the outboard area of the VV. The VV, segmented by 20 degree modules, is capable to accommodate 40 MW RF power systems. The machine has been designed to house10 MW Negative Neutral Beam injection (NNBI) systems. Tungsten (W) and Liquid Lithium (L-Li) have been chosen as the divertor plates material, and Argon and Neon as the injected impurities to mitigate the thermal loads

  1. [Emission and control of gases and odorous substances from animal housing and manure depots].

    Science.gov (United States)

    Hartung, J

    1992-02-01

    Agricultural animal production in increasingly regarded as a source of gases which are both aggravating and ecologically harmful. An overview of the origin, number and quantity of trace gases emitted from animal housing and from manure stores is presented and possible means of preventing or reducing them are discussed. Of the 136 trace gases in the air of animal houses, odorous substances, ammonia and methane are most relevant to the environment. The role played by the remaining gases is largely unknown. Quantitative information is available for 23 gases. The gases are emitted principally from freshly deposited and stored faeces, from animal feed and from the animals themselves. Future work should determine sources and quantities of the gases emitted from animal housing more precisely and should aim to investigate the potential of these gases to cause damage in man, animals and environment. Odorous substances have an effect on the area immediately surrounding the animal housing. They can lead to considerable aggravation in humans. For years, VDI1 guidelines (3471/72), which prescribe distances between residential buildings and animal housing, have been valuable in preventing odour problems of this kind. Coverings are suitable for outside stores. The intensity of the odour from animal housing waste air increases from cattle through to hens and pigs; it is also further affected by the type of housing, the age of the animals and the purpose for which they are being kept. Methods of cleaning waste air (scrubbers/biofilters) are available for problematic cases. The need for guidelines to limit emissions from individual outside manure stores (lagoons) is recognised. Total ammonia emissions from animal production in the Federal Republic of Germany (up to 1989) are estimated at approximately 300,000 to 600,000 t/year. There is a shortage of satisfactory and precise research on the extent of emissions, in particular on those from naturally ventilated housing. It is

  2. Poverty, housing, and the rural slum: policies and the production of inequities, past and present.

    Science.gov (United States)

    Ramirez, Sarah M; Villarejo, Don

    2012-09-01

    We studied historical materials to examine the conditions that gave rise to California's rural slums, the consequences of their emergence, and how interpretations of housing, health, and welfare policies by government officials, and public health officials in particular, produced health inequities for residents of these communities. For more than a century, successive groups of immigrants and domestic migrant laborers have worked on California's farms and faced numerous challenges, among them a lack of safe and affordable housing, poor working conditions, and denial of public services. Although these experiences are not new, nor are they unique to agricultural workers, they illustrate a longer history in which inequities and injustices have been rooted in the exploitation and disposability of labor. Ameliorating or even redressing inequities will require understanding the social determinants of health through ecological approaches that can overcome the historical, social, and political causes of inequity.

  3. ANALYSIS OF THE EFFECTS OF THE ROOFING DESIGN ON HEAT STRESS IN DAIRY COW HOUSING

    Directory of Open Access Journals (Sweden)

    Paolo Liberati

    2008-12-01

    Full Text Available A simulation model determining the heat flow exchange between housed animals and the roofing was developed considering various relevant factors: constructive materials, slope, height, orientation, latitude, external air temperature, solar load, animal position. Results show that the most important factor to reduce heat load is the insulation. For non-insulated roofing the slope and the orientation are the most relevant factors. Considering the total exchanged energy, the non insulated roof has a good nocturnal global behaviour.

  4. MODEL FOR ELECTRIC LOAD OF COMMUNITY HOUSING PROJECTS TO INVESTIGATE “GENERATOR – ACCUMULATOR – CONSUMER” SYSTEM WHILE USING MONTE-CARLO METHOD

    Directory of Open Access Journals (Sweden)

    K. V. Dobrego

    2017-01-01

    Full Text Available Nowadays we observe rather rapid growth of energy accumulators market. There are prerequisites to their extensive application in Belarus. In spite of technology development problems pertaining to optimization of electric power and their operation under conditions of specific systems “generator – accumulator – consumer” (GAC have not obtained proper consideration. At the same time tuning and optimization of the GAC system may provide competitive advantages to various accumulating systems because application of accumulator batteries in non-optimal charge – discharge conditions reduces its operating resource. Optimization of the GAC system may include utilization of hybrid accumulator systems together with heterogeneous chemical and mechanical accumulators, tuning of system controller parameters etc. Research papers present a great number of empirical and analytical methods for calculation of electric loads. These methods use the following parameters as initial data: time-averaged values of actual electric power consumption, averaged apartment electric loads, empirical and statistical form coefficients, coefficients of maximum electric load for a group of uniform consumers. However such models do not meet the requirements of detailed simulation of relatively small system operation when the simulation must correspond to non-stationary, non-averaged, stochastic load nature. The paper provides a simple approach to the detailed simulation of electric loads in regard to small projects such as multi-unit apartment building or small agricultural farm. The model is formulated both in physical and algorithmic terms that make it possible to be easily realized in any programming environment. The paper presents convergence of integral electric power consumption, which is set by the model, to statistically averaged parameters. Autocorrelation function has been calculated in the paper that shows two scales for autocorrelation of simulated load diagrams

  5. Application of Breathing Architectural Members to the Natural Ventilation of a Passive Solar House

    Directory of Open Access Journals (Sweden)

    Kyung-Soon Park

    2016-03-01

    Full Text Available The efficient operation of a passive solar house requires an efficient ventilation system to prevent the loss of energy and provide the required ventilation rates. This paper proposes the use of “breathing architectural members” (BAMs as passive natural ventilation devices to achieve much improved ventilation and insulation performance compared to mechanical ventilation. Considering the importance of evaluating the ventilation and insulation performances of the members, we also propose numerical models for predicting the heat and air movements afforded by the members. The numerical model was validated by comparison with experimental results. The effectiveness of the BAMs was also verified by installation in houses located in an area with warm climate. For this purpose, chamber experiments were performed using samples of the BAMs, as well as numerical simulations to assess natural ventilation and heat load. The main findings of the study are as follows: (1 the one-dimensional chamber experiments confirmed the validity of the numerical models for predicting the heat and air movements afforded by the BAMs. Comparison of the experimental and calculated values for the temperature of air that flowed into the room from outside revealed a difference of less than 5%; (2 observations of the case studies in which BAMs were installed in the ceilings and exterior walls of Tokyo model houses revealed good annual ventilation and energy-saving effects. When BAMs with an opening area per unit area of A = 0.002 m2/m2 were applied to three surfaces, the required ventilation rate was 0.5 ACH (air changes per hour, and this was achieved consistently. Compared to a house with general insulation and conventional mechanical ventilation, heating load was reduced by 15.3%–40.2% depending on the BAM installation points and the differing areas of the house models.

  6. Energy efficiency and load curve impacts

    International Nuclear Information System (INIS)

    Feilberg, Nicolai

    2002-01-01

    One of SINTEF Energy Research's European RTD projects is the two-year EFFLOCOM (Energy EFFiciency and LOad curve impacts of COMmercial development in competitive markets). This project will determine the end-user response of different market-related services offered in deregulated power markets. The project will investigate the possibility of influencing load curves by using different price signals and two-way communications via Internet. The partners are from Denmark. Finland, England, France and Norway. SINTEF Energy Research is in charge of the project management. During the project, the changes in load curves will he studied in the in the participating countries before and after deregulation. Specific issues are the use of ICT, time- and situation-dependent tariffs and smart-house technology. The project will consist of 5 work packages that will give recommendations about new methods, guidelines and tools to promote effective use of energy in the partner countries. The total budget is EUR 692 000. (author)

  7. Demonstration of Load-Follow Simulation with VERA-CS and Standalone BISON

    Energy Technology Data Exchange (ETDEWEB)

    Stimpson, Shane G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-01-24

    In this report, load-follow simulations using VERA-CS with one-way coupling to standalone BISON has been demonstrated including both a single rod with a full cycle of load-follow operations and a quarter-core model with a single month of load-follow.

  8. Improved performance evaluation of road pavements by using measured tyre loading

    CSIR Research Space (South Africa)

    Maina, JW

    2008-11-01

    Full Text Available This paper presents evaluation of road pavement response under the loading of typical dual and single truck tyre configurations. Locally developed Stress-In-Motion (SIM) technology was used to quantify three-dimensional (3D) shapes of the tyre road...

  9. Impacts of alternative residential energy standards - Rural Housing Amendments Study, Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Balistocky, S.; Bohn, A.A.; Heidell, J.A.; Hendrickson, P.L.; Lee, A.D.; Pratt, R.G.; Taylor, Z.T.

    1985-11-01

    This report has examined the role of manufactured housing in the housing market, the energy impacts of three manufactured housing standards and three site-built standards in 13 cities, and the economic impacts of those standards in 6 cities. The three standards applied to manufactured housing are the HUD Title VI standard (Manufactured Housing Construction and Safety Standards, or MHCSS), the Hud Title II-E standard, and the existing FmHA Title V standard. Those applied to site-built homes are the HUD Minimum Property Standards (MPS), the ASHRAE 90A-80 standard, and the FmHA Title V standard. Based on energy consumption alone, these analyses show that the FmHA Title V standard is the most stringent standard for both housing types (a single-section menufactured home and a single-story detached ''ranch house''). The HUD Title VI standard is the least stringent for manufactured homes, while the HUD Minimum Property Standards are the least stringent for site-built homes. Cost-effectiveness comparisons required by the Act were made for the two prototypical homes. Results of this preliminary economic analysis indicate that none of the site-built standards reflect minimum life-cycle cost as a basic criterion of their development. For manufactured homes, both the FmHA standard and the HUD Title II-E standard reduce life-cycle cost and effect positive first-year cash flows in all cities analyzed when electric resistance heating is assumed. When natural gas heating is used, both standards pass the life-cycle cost test in all cities, but the FmHA standard fails the cash flow test in all but one city. However, in the worst case, net monthly expenditures in the first year are increased by less than $9.

  10. Modeling and Measurement of Sustained Loading and Temperature-Dependent Deformation of Carbon Fiber-Reinforced Polymer Bonded to Concrete.

    Science.gov (United States)

    Jeong, Yoseok; Lee, Jaeha; Kim, WooSeok

    2015-01-29

    This paper aims at presenting the effects of short-term sustained load and temperature on time-dependent deformation of carbon fiber-reinforced polymer (CFRP) bonded to concrete and pull-off strength at room temperature after the sustained loading period. The approach involves experimental and numerical analysis. Single-lap shear specimens were used to evaluate temperature and short-term sustained loading effects on time-dependent behavior under sustained loading and debonding behavior under pull-off loading after a sustained loading period. The numerical model was parameterized with experiments on the concrete, FRP, and epoxy. Good correlation was seen between the numerical results and single-lap shear experiments. Sensitivity studies shed light on the influence of temperature, epoxy modulus, and epoxy thickness on the redistribution of interfacial shear stress during sustained loading. This investigation confirms the hypothesis that interfacial stress redistribution can occur due to sustained load and elevated temperature and its effect can be significant.

  11. Long-term impacts on sewers following food waste disposer installation in housing areas.

    Science.gov (United States)

    Mattsson, Jonathan; Hedström, Annelie; Viklander, Maria

    2014-01-01

    To increase biogas generation and decrease vehicle transportation of solid waste, the integration of food waste disposers (FWDs) into the wastewater system has been proposed. However, concerns have been raised about the long-term impact of the additional load of the FWDs on sewer systems. To examine the said impact, this study has used closed-circuit television inspection techniques to evaluate the status of 181 concrete pipes serving single family housing areas with a diameter of 225 mm, ranging from a 100% connection rate of households with an FWD to none. A minor study was also performed on a multi-family housing area, where mainly plastic pipes (200 mm) were used. The extent and distribution of deposits related to the ratio of FWDs, inclination and pipe sagging (backfalls) were ascertained by using linear regression and analysis of variance. The results showed that FWDs have had an impact on the level of deposits in the sewer, but this has, in turn, been of minor significance. With a high connection rate of FWDs upstream of a pipe, the extent of the total level of deposits, as well as finer sediments, was statistically determined to be greater. However, the majority of the deposits were observed to be small, which would suggest the impact of FWDs on sewer performance to be minor. As food waste not compatible with the FWD was seen in the sewers, educational campaigns could be beneficial to further lower the risks of sewer blocking.

  12. Development of a Measure of Housing and Housing Services.

    Science.gov (United States)

    Clark, Colleen; Young, M Scott; Teague, Gregory; Rynearson-Moody, Sarah

    2016-01-01

    The Housing Program Measure (HPM) was designed to document critical elements of a range of housing program types and associated services. Qualitative methods, including literature review and open-ended interviews, were used to determine pertinent HPM domains and to develop the pool of items. The measure was pre-tested, and reliability and validity analyses were applied to revise and strengthen the measure. The resulting measure furthers homelessness research by providing a tool that can be used to define housing and housing services interventions across diverse projects and disciplines, to facilitate program management by matching housing resources to the needs of homeless individuals, and to support model development by measuring progress to goals.

  13. Dynamic load testing on the bearing capacity of prestressed tubular concrete piles in soft ground

    Science.gov (United States)

    Yu, Chuang; Liu, Songyu

    2008-11-01

    Dynamic load testing (DLT) is a high strain test method for assessing pile performance. The shaft capacity of a driven PTC (prestressed tubular concrete) pile in marine soft ground will vary with time after installation. The DLT method has been successfully transferred to the testing of prestressed pipe piles in marine soft clay of Lianyungang area in China. DLT is investigated to determine the ultimate bearing capacity of single pile at different period after pile installation. The ultimate bearing capacity of single pile was founded to increase more than 70% during the inventing 3 months, which demonstrate the time effect of rigid pile bearing capacity in marine soft ground. Furthermore, the skin friction and axial force along the pile shaft are presented as well, which present the load transfer mechanism of pipe pile in soft clay. It shows the economy and efficiency of DLT method compared to static load testing method.

  14. Cognitive load theory: Practical implications and an important challenge

    Directory of Open Access Journals (Sweden)

    Jimmie Leppink, Ph.D.

    2017-10-01

    Full Text Available The field of medical education has adopted a wide variety of theories from other fields. A fairly recent example is cognitive load theory, which originated in educational psychology. Several empirical studies inspired by cognitive load theory and reviews of practical implications of cognitive load theory have contributed to guidelines for the design of medical education. Simultaneously, several research groups have developed instruments for the measurement of cognitive load in a medical education context. These developments notwithstanding, obtaining evidence for different types of cognitive load remains an important challenge. Therefore, the aim of this article is twofold: to provide medical educators with three key guidelines for the design of instruction and assessment and to discuss several fundamental issues in the remaining challenges presented by different types of cognitive load. The guidelines revolve around minimizing cognitive activity that does not contribute to learning, working with specific learning goals in mind, and appreciating the multifaceted relation between learning and assessment. Key issues around the types of cognitive load include the context in which learning occurs, the continued use of single-item mental effort ratings, and the timing of cognitive load and learning outcome measurements.

  15. Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Tests and researches have been performed with the objectives to establish an evaluation technology for load leveling effect by using a small photovoltaic power generation system for residential use, to clarify the effectiveness of the system as a discrete power supply source through demonstration operation, and furthermore to achieve optimization of designs of the small photovoltaic power generation system for residential use. This paper summarizes the achievements in fiscal 1996. The current fiscal year has performed collection of data of the demonstration operation, checked the consistency in photovoltaic power generation characteristics, and housing and distribution line load characteristics, and the results were mounted on the database. The demonstration operation data were used to analyze and evaluate the facility utilization rate in the photovoltaic power generation, photovoltaic power generation dependence of the house load, load rate, and peak load reduction rate. As a result, it was found that not much of the peak load reduction effect by the photovoltaic power generation was recognized because the house load is related mainly on lighting load. However, as seen from the distribution line load, the peak load reduction was recognized when the house load and the commercial and industrial load are mixed, whereas it was revealed that the reduction effect is worth evaluation. (NEDO)

  16. Bottom loaded filter for radioactive liquid

    International Nuclear Information System (INIS)

    Wendland, W.G.

    1980-01-01

    A specification is given for a bottom loaded filter assembly for filtering radioactive liquids through a replaceable cartridge filter, which includes a lead-filled jacket enveloping a housing having a chamber therein for the filter cartridge. A track arrangement carries a hatch for sealing the chamber. A spacer plug supports the cartridge within guide means associated with the inlet conduit in the chamber. The plug and cartridge drop out of the chamber when the hatch is unbolted and moved laterally of the chamber along the track. During cartridge replacement a new plug and cartridge are supported in the guide means by a spacer bar inserted across the track means under the chamber. The hatch is then slid under the chamber and bolted to a flange on the housing, engaging an O-ring to seal the chamber. (author)

  17. Sydney Opera House Rise

    DEFF Research Database (Denmark)

    2013-01-01

    Sydney Opera House Exhibition (2013) A CITA research and exhibition project, for Sydney Opera House exhibition "Danish Design at the House".......Sydney Opera House Exhibition (2013) A CITA research and exhibition project, for Sydney Opera House exhibition "Danish Design at the House"....

  18. Economic analysis of passive houses and low-energy houses compared with standard houses

    International Nuclear Information System (INIS)

    Audenaert, A.; Cleyn, S.H. de; Vankerckhove, B.

    2008-01-01

    As the energy demand used for space heating accounts for 78% of EU15 household delivered energy consumption, significant reductions in energy demand can be achieved by promoting low-energy buildings. Our study investigates three building types: the standard house, the low-energy house and the passive house. As more far-reaching measures concerning energy savings usually lead to higher investments, the aim of our study is to perform an economic analysis in order to determine the economic viability of the three building types

  19. Assessment of the transportation route of oversize and excessive loads in relation to the load-bearing capacity of existing bridges

    Science.gov (United States)

    Doležel, Jiří; Novák, Drahomír; Petrů, Jan

    2017-09-01

    Transportation routes of oversize and excessive loads are currently planned in relation to ensure the transit of a vehicle through critical points on the road. Critical points are level-intersection of roads, bridges etc. This article presents a comprehensive procedure to determine a reliability and a load-bearing capacity level of the existing bridges on highways and roads using the advanced methods of reliability analysis based on simulation techniques of Monte Carlo type in combination with nonlinear finite element method analysis. The safety index is considered as a main criterion of the reliability level of the existing construction structures and the index is described in current structural design standards, e.g. ISO and Eurocode. An example of a single-span slab bridge made of precast prestressed concrete girders of the 60 year current time and its load bearing capacity is set for the ultimate limit state and serviceability limit state. The structure’s design load capacity was estimated by the full probability nonlinear MKP analysis using a simulation technique Latin Hypercube Sampling (LHS). Load-bearing capacity values based on a fully probabilistic analysis are compared with the load-bearing capacity levels which were estimated by deterministic methods of a critical section of the most loaded girders.

  20. Housing and respiratory health at older ages.

    Science.gov (United States)

    Webb, E; Blane, D; de Vries, Robert

    2013-03-01

    A large proportion of the population of England live in substandard housing. Previous research has suggested that poor-quality housing, particularly in terms of cold temperatures, mould, and damp, poses a health risk, particularly for older people. The present study aimed to examine the association between housing conditions and objectively measured respiratory health in a large general population sample of older people in England. Data on housing conditions, respiratory health and relevant covariates were obtained from the second wave of the English Longitudinal Study of Ageing. Multivariate regression methods were used to test the association between contemporary housing conditions and respiratory health while accounting for the potential effect of other factors; including social class, previous life-course housing conditions and childhood respiratory health. Older people who were in fuel poverty or who did not live in a home they owned had significantly worse respiratory health as measured by peak expiratory flow rates. After accounting for covariates, these factors had no effect on any other measures of respiratory health. Self-reported housing problems were not consistently associated with respiratory health. The housing conditions of older people in England, particularly those associated with fuel poverty and living in rented accommodation, may be harmful to some aspects of respiratory health. This has implications for upcoming UK government housing and energy policy decisions.

  1. Factor structure underlying components of allostatic load.

    Directory of Open Access Journals (Sweden)

    Jeanne M McCaffery

    Full Text Available Allostatic load is a commonly used metric of health risk based on the hypothesis that recurrent exposure to environmental demands (e.g., stress engenders a progressive dysregulation of multiple physiological systems. Prominent indicators of response to environmental challenges, such as stress-related hormones, sympatho-vagal balance, or inflammatory cytokines, comprise primary allostatic mediators. Secondary mediators reflect ensuing biological alterations that accumulate over time and confer risk for clinical disease but overlap substantially with a second metric of health risk, the metabolic syndrome. Whether allostatic load mediators covary and thus warrant treatment as a unitary construct remains to be established and, in particular, the relation of allostatic load parameters to the metabolic syndrome requires elucidation. Here, we employ confirmatory factor analysis to test: 1 whether a single common factor underlies variation in physiological systems associated with allostatic load; and 2 whether allostatic load parameters continue to load on a single common factor if a second factor representing the metabolic syndrome is also modeled. Participants were 645 adults from Allegheny County, PA (30-54 years old, 82% non-Hispanic white, 52% female who were free of confounding medications. Model fitting supported a single, second-order factor underlying variance in the allostatic load components available in this study (metabolic, inflammatory and vagal measures. Further, this common factor reflecting covariation among allostatic load components persisted when a latent factor representing metabolic syndrome facets was conjointly modeled. Overall, this study provides novel evidence that the modeled allostatic load components do share common variance as hypothesized. Moreover, the common variance suggests the existence of statistical coherence above and beyond that attributable to the metabolic syndrome.

  2. Cognitive Load of Learner Control: Extraneous or Germane Load?

    Directory of Open Access Journals (Sweden)

    Mieke Vandewaetere

    2013-01-01

    Full Text Available Computer-based learning environments become more tailored when learners can exert control over one or more parts of the learning process. Learner control (LC demands additional efforts of learners because, in addition to learning, they also have to monitor that learning. As a consequence, LC may cause additional cognitive load and even cognitive overload. The central question in this study is what type of cognitive load is induced by LC and whether the experienced load is related to learning outcomes. For this study, half of the students had control over task selection, while the other half had not. Within each condition, students were assigned to a single treatment, with the primary task to solely focus on the learning content, and a dual treatment, comprising a primary task and a secondary task. The results indicate that LC did not impose higher cognitive load as measured by secondary task scores and mental effort ratings.

  3. Assisted Housing - Public Housing Developments - National Geospatial Data Asset (NGDA)

    Data.gov (United States)

    Department of Housing and Urban Development — The general location of an entire Public Housing Development. A distinct address is chosen to represent the general location of an entire Public Housing Development,...

  4. Controlling Buffeting Loads by Rudder and Piezo-Actuation

    Science.gov (United States)

    Moses, Robert W.; Pototzky, Anthony S.; Henderson, Douglas A.; Galea, Stephen C.; Manokaran, Donald S.; Zimcik, David G.; Wickramasinghe, Viresh; Pitt, Dale M.; Gamble, Michael A.

    2005-01-01

    High performance aircraft, especially those with twin vertical tails, encounter unsteady buffet loads when flying at high angles of attack. These stochastic loads result in significant stresses, which may cause fatigue damage leading to restricted capabilities and availability of the aircraft. An international collaborative research activity among Australia, Canada and the United States, conducted under the auspices of The Technical Cooperation Program (TTCP) contributed resources toward a program that coalesced a broad range of technical knowledge and expertise into a single investigation to demonstrate the enhanced performance and capability of the advanced active Buffet Load Alleviation ( ) control system in preparation for a flight test demonstration. The research team investigated the use of active structural control to alleviate the damaging structural response to these loads by applying advanced directional piezoelectric actuators, the aircraft rudder, switch mode amplifiers, and advanced control strategies on an F/A-18 aircraft empennage. Some results of the full-scale investigation are presented herein.

  5. Strength of shock-loaded single-crystal tantalum [100] determined using in situ broadband x-ray Laue diffraction.

    Science.gov (United States)

    Comley, A J; Maddox, B R; Rudd, R E; Prisbrey, S T; Hawreliak, J A; Orlikowski, D A; Peterson, S C; Satcher, J H; Elsholz, A J; Park, H-S; Remington, B A; Bazin, N; Foster, J M; Graham, P; Park, N; Rosen, P A; Rothman, S R; Higginbotham, A; Suggit, M; Wark, J S

    2013-03-15

    The strength of shock-loaded single crystal tantalum [100] has been experimentally determined using in situ broadband x-ray Laue diffraction to measure the strain state of the compressed crystal, and elastic constants calculated from first principles. The inferred strength reaches 35 GPa at a shock pressure of 181 GPa and is in excellent agreement with a multiscale strength model [N. R. Barton et al., J. Appl. Phys. 109, 073501 (2011)], which employs a hierarchy of simulation methods over a range of length scales to calculate strength from first principles.

  6. The impact of housing policies and housing markets on ethnic spatial segregation

    DEFF Research Database (Denmark)

    Andersen, Hans Skifter; Andersson, Roger; Wessel, Terje

    2015-01-01

    This paper examines how ethnic segregation is connected to an ethnic division of the housing market and a spatial separation of different housing tenures in four Nordic cities. Explanations for the differences across the cities are found by comparing housing markets and housing policies....... The housing markets are in all four cities ethnically segmented with high concentrations of immigrants in some forms of tenures (especially social/public housing) and low concentrations in others. We further discuss the reasons for the observed pattern. The paper shows that the spatial distribution...... housing, while co-operative housing is crucial in the fourth. It is also shown that a policy of neighbourhood tenure mix in one of the cities has resulted in a relatively low degree of segregation in spite of high concentrations of immigrants in social/public housing....

  7. Energy Efficient Renovation of Social Housing

    DEFF Research Database (Denmark)

    Bech-Nielsen, Grith; Christiansen, Michael

    In years to come the social housing sector (SH) must undergo renovation. The SH is out of step with modern requirements when it comes to plan arrangements, energy frame calcu-lation, flexible building services and social challenges. A way to solve such challenges in an environmentally, economically......, such as residents, housing administration, politicians, advi-sors, producers and contractors. Secondly we present follow up methods for developing an overall future energy renova-tion SH strategy. Our project contributes to the building sector by suggesting new methods for meeting challenges concerning energy......), (2) workshops and (3) seminars for qualifying (4) the definition of a common framework for (5) the development and (6) acceptance of the actual energy renovation strategy, which will then be transformed into action plans in the form of (7) ”common screening” of housing and housing areas as a basis...

  8. Distributions of radon in houses as a basis for radiological protection: Swedish experience

    International Nuclear Information System (INIS)

    Swedjemark, G.A.; Maekitalo, A.

    1991-01-01

    As a basis for protection against high radon exposure in houses, three types of sampling are adequate: (1) random sampling, (2) identification of regions with high risk for radon problems in houses, and (3) searching for houses with high levels. The objectives can be achieved in a single study. In Sweden, several types of sampling have been used. The motive for the Swedish choice of strategy and the results of experience are discussed. Examples of reasons for different strategies are political aims and differences in the organisation of the radiation protection in houses. Random sampling was carried out in 80-82 in homes throughout Sweden. The strategy for the local authorities responsible for points 2 and 3 above differs because of local conditions. In general, they select houses for measurement on the basis of radon risk maps, information on high content of radium in houses, previous measurements, and reports from home owners. Comparison with the random sampling study has shown that they have been five times more successful than chance in their selection for measurements in the one-family houses. (Author)

  9. Measurement of blowdown flow rates using load cells

    International Nuclear Information System (INIS)

    Dolas, P.K.; Venkat Raj, V.; Ghosh, A.K.; Murty, L.G.K.; Muralidhar Rao, S.

    1980-01-01

    To establish a reliable method for measuring two-phase flow, experiments were planned for measurement of transient single phase flow rates from vessels using load cells. Suitability of lead-zirconate-titanate piezoelectric ceramic discs was examined. Discharge time constant of the disc used was low, leading to large measurement errors. Subsequently, experiments were carried out using strain gauge load cells and these were found satisfactory. The unsteady flow equation has been derived for the system under investigation. The equation has been solved numerically using the fourth order Runge-Kutta method and also by integrating it analytically. The experimental results are compared with the theoretical results and presented in this report. (auth.)

  10. Examing the prospective of implementing passive house standards in providing sustainable schools

    Science.gov (United States)

    Suhaili, Wan Farhani; Shahrill, Masitah

    2018-04-01

    This study examines the potential of implementing the passive house standards to reduce energy consumption on school buildings in Brunei. Furthermore, it investigates whether sustainable school buildings make business sense to the government. To do this, conventional and Passive House primary school buildings are compared in terms of their performances using the Passive House Planning Package as well as the Ecotect environmental analysis tool. The findings indicated that by replacing lower U-values building fabrics brought a significantly reduction in the cooling demand of 54%. Whereas, Ecotect models have demonstrated that the heating and cooling loads have tremendously reduced to 75% by reorienting the location of the building to south elevation and by replacing the building fabrics with a lower U-values. These findings were then evaluated with a cost benefit analysis that proved to save cost energy annually from air-conditioning usage from a typical primary school with eight years of pay back period.

  11. Single Family Loan Sale Initiative - Neighborhood Stabilization Outcome Pool Offering

    Data.gov (United States)

    Department of Housing and Urban Development — The FHA Office of Housing is conducting a series of mortgage loan sales under the Single Family Loan Sale (SFLS) Initiative. The current sales structure consists of...

  12. Loading pattern optimization by multi-objective simulated annealing with screening technique

    International Nuclear Information System (INIS)

    Tong, K. P.; Hyun, C. L.; Hyung, K. J.; Chang, H. K.

    2006-01-01

    This paper presents a new multi-objective function which is made up of the main objective term as well as penalty terms related to the constraints. All the terms are represented in the same functional form and the coefficient of each term is normalized so that each term has equal weighting in the subsequent simulated annealing optimization calculations. The screening technique introduced in the previous work is also adopted in order to save computer time in 3-D neutronics evaluation of trial loading patterns. For numerical test of the new multi-objective function in the loading pattern optimization, the optimum loading patterns for the initial and the cycle 7 reload PWR core of Yonggwang Unit 4 are calculated by the simulated annealing algorithm with screening technique. A total of 10 optimum loading patterns are obtained for the initial core through 10 independent simulated annealing optimization runs. For the cycle 7 reload core one optimum loading pattern has been obtained from a single simulated annealing optimization run. More SA optimization runs will be conducted to optimum loading patterns for the cycle 7 reload core and results will be presented in the further work. (authors)

  13. Temperature and Pressure Dependences of the Elastic Properties of Tantalum Single Crystals Under Tensile Loading: A Molecular Dynamics Study

    Science.gov (United States)

    Li, Wei-bing; Li, Kang; Fan, Kan-qi; Zhang, Da-xing; Wang, Wei-dong

    2018-04-01

    Atomistic simulations are capable of providing insights into physical mechanisms responsible for mechanical properties of the transition metal of Tantalum (Ta). By using molecular dynamics (MD) method, temperature and pressure dependences of the elastic properties of Ta single crystals are investigated through tensile loading. First of all, a comparative study between two types of embedded-atom method (EAM) potentials is made in term of the elastic properties of Ta single crystals. The results show that Ravelo-EAM (Physical Review B, 2013, 88: 134101) potential behaves well at different hydrostatic pressures. Then, the MD simulation results based on the Ravelo-EAM potential show that Ta will experience a body-centered-cubic (BCC) to face-centered-cubic (FCC) phase transition before fracture under tensile loading at 1 K temperature, and model size and strain rate have no obvious effects on tensile behaviors of Ta. Next, from the simulation results at the system temperature from 1 to 1500 K, it can be derived that the elastic modulus of E 100 linearly decrease with the increasing temperature, while the yielding stress decrease with conforming a quadratic polynomial formula. Finally, the pressure dependence of the elastic properties is performed from 0 to 140 GPa and the observations show that the elastic modulus increases with the increasing pressure overall.

  14. Inductrack III configuration--a maglev system for high loads

    Science.gov (United States)

    Post, Richard F

    2013-11-12

    Inductrack III configurations are suited for use in transporting heavy freight loads. Inductrack III addresses a problem associated with the cantilevered track of the Inductrack II configuration. The use of a cantilevered track could present mechanical design problems in attempting to achieve a strong enough track system such that it would be capable of supporting very heavy loads. In Inductrack III, the levitating portion of the track can be supported uniformly from below, as the levitating Halbach array used on the moving vehicle is a single-sided one, thus does not require the cantilevered track as employed in Inductrack II.

  15. Typical load shapes for six categories of Swedish commercial buildings

    Energy Technology Data Exchange (ETDEWEB)

    Noren, C.

    1997-01-01

    In co-operation with several Swedish electricity suppliers, typical load shapes have been developed for six categories of commercial buildings located in the south of Sweden. The categories included in the study are: hotels, warehouses/grocery stores, schools with no kitchen, schools with kitchen, office buildings, health, health buildings. Load shapes are developed for different mean daily outdoor temperatures and for different day types, normally standard weekdays and standard weekends. The load shapes are presented as non-dimensional normalized 1-hour load. All measured loads for an object are divided by the object`s mean load during the measuring period and typical load shapes are developed for each category of buildings. Thus errors were kept lower as compared to use of W/m{sup 2}-terms. Typical daytime (9 a.m. - 5 p.m.) standard deviations are 7-10% of the mean values for standard weekdays but during very cold or warm weather conditions, single objects can deviate from the typical load shape. On weekends, errors are higher and depending on very different activity levels in the buildings, it is difficult to develop weekend load shapes with good accuracy. The method presented is very easy to use for similar studies and no building simulation programs are needed. If more load data is available, a good method to lower the errors is to make sure that every category only consists of objects with the same activity level, both on weekdays and weekends. To make it easier to use the load shapes, Excel load shape workbooks have been developed, where it is even possible to compare typical load shapes with measured data. 23 refs, 53 figs, 20 tabs

  16. Make the heat hotter. - marketing district heating to households in detached houses

    Energy Technology Data Exchange (ETDEWEB)

    Sernhed, Kerstin; Pyrko, Jurek

    2008-09-15

    For district heating (DH) companies, to expand in low heat density areas such as detached houses, it is essential to obtain a high rate of connections to the district-heating network in order to enhance the cost effectiveness. Marketing district heating to house owners is, however, a fairly different matter from selling it to customers in industrial, commercial, and multi-family buildings. Suitable market strategies need to be developed and the need for information about potential customers' preferences and attitudes are of great importance since the house-owners often constitute a heterogeneous group where different households have different requirements. This paper investigates a case of one Swedish district heating company's marketing activities and expansion strategies in a single family house area where the customers were offered conversion of their direct resistive electric heating (DEH) into district heating (DH). 88 out of 111 houses were converted in 2002. Four years later, interviews were carried out with 23 of the households in the area, both with those who had accept-ed the district heating offer and those who had not. The study shows that apart from the economic aspects, thermal comfort, aesthetics and practicalities also affected the buying decision. Since the different economic aspects of the offer were complex, it was very difficult for the households to make a strictly rational economical decision. Statistical analysis confirmed that variables such as age, type of household and energy use level could, to some extent, be related to the decision to convert from electric heating to district heating. Timing, low prices and the total solutions presented to the households were crucial factors in the success of the marketing strategy.

  17. Retrofitting Domestic Hot Water Heaters for Solar Water Heating Systems in Single-Family Houses in a Cold Climate: A Theoretical Analysis

    Directory of Open Access Journals (Sweden)

    Björn Karlsson

    2012-10-01

    Full Text Available One of the biggest obstacles to economic profitability of solar water heating systems is the investment cost. Retrofitting existing domestic hot water heaters when a new solar hot water system is installed can reduce both the installation and material costs. In this study, retrofitting existing water heaters for solar water heating systems in Swedish single-family houses was theoretically investigated using the TRNSYS software. Four simulation models using forced circulation flow with different system configurations and control strategies were simulated and analysed in the study. A comparison with a standard solar thermal system was also presented based on the annual solar fraction. The simulation results indicate that the retrofitting configuration achieving the highest annual performance consists of a system where the existing tank is used as storage for the solar heat and a smaller tank with a heater is added in series to make sure that the required outlet temperature can be met. An external heat exchanger is used between the collector circuit and the existing tank. For this retrofitted system an annual solar fraction of 50.5% was achieved. A conventional solar thermal system using a standard solar tank achieves a comparable performance for the same total storage volume, collector area and reference conditions.

  18. Family Open House

    Science.gov (United States)

    Search Family Open House Join us for an afternoon of science fun. The Fermilab Family Open House is a party for children of all ages to learn about the world of physics. The Open House is supported by Open House? Check out our YouTube video to learn more! Explore physics concepts with hands-on

  19. Innovativeness in housing construction and the role of the Housing Fund: From residence to an integral living environment

    Directory of Open Access Journals (Sweden)

    Zdravko Mlinar

    2008-01-01

    Full Text Available This article attempts to contribute to clarification of the conditions and actors impacting innovativeness in housing construction and the management of space. It concentrates on the role of the Slovenian national Housing Fund, which is too restricted and lacks appropriate legal bases and means, and also – according to some evaluations – the aspiration to assert its innovative and developmental role. The Fund is focussed on the financial-economic aspects of providing non-profit housing and housing for the market. Currently attention is primarily directed towards its legal-organizational structure and its transformation into an independent company. This neglects broader consideration of socio-spatial change, developmental directions and values in the context of the information age (Lisbon Strategy, which call for innovative sociological, architectural and urbanistic solutions. Mindsets, legal norms and institutions in Slovenia are lagging behind these changes. Thus, housing is still mainly treated as a discrete segment. In order to perform their task in this new framework, which demands more integral treatment of the everyday living environment and reintegration of living, work and recreation, the mandate of the housing funds must no longer be confined merely to housing. Several examples of innovative design as well as their limitations are presented, together with examples of good international practice.

  20. Radon house doctor

    International Nuclear Information System (INIS)

    Nitschke, I.A.; Brennan, T.; Wadach, J.B.; O'Neil, R.

    1986-01-01

    The term house doctor may be generalized to include persons skilled in the use of instruments and procedures necessary to identify, diagnose, and correct indoor air quality problems as well as energy, infiltration, and structural problems in houses. A radon house doctor would then be a specialist in radon house problems. Valuable experience in the skills necessary to be developed by radon house doctors has recently been gained in an extensive radon monitoring and mitigation program in upstate New York sponsored by Niagara Mohawk Power Corporation and the New York State Energy Research and Development Authority. These skills, to be described in detail in this paper, include: (i) the use of appropriate instruments, (ii) the evaluation of the symptoms of a radon-sick house, (iii) the diagnostic procedures required to characterize radon sources in houses, (iv) the prescription procedures needed to specify treatment of the problem, (v) the supervision of the implementation of the treatment program, (vi) the check-up procedures required to insure the house cured of radon problems. 31 references, 3 tables

  1. Housing First or no housing? Housing and homelessness at the end of alcohol and drug treatment.

    Science.gov (United States)

    Dyb, Evelyn

    2016-10-01

    The rate of alcohol and drug dependency is high among homeless persons in Norway as well as in other Western societies. National homeless surveys also show a certain correlation between discharge from institutions and homelessness. However, the rate of homelessness versus the rate with fixed abode at the end of specialised alcohol and drug treatment has not been examined using quantitative methods. A cross-sectional survey was conducted in alcohol and drug treatment units in the national health services and private clinics. The survey investigates the housing outcome at the end of treatment compared to the situation at the start of treatment using an individual questionnaire for patients ending treatment in a specific time window. Housing outcome is measured by the odds ratio of having a fixed abode at the end of treatment in relation to main intoxicating substance, type of treatment (in- and outpatient), completing versus cutting short the treatment, housing situation at the start of treatment, socioeconomic capital, mental health problems, individual plan, medical assisted treatment, and a set of background variables. The housing versus homeless situation hardly changes during the treatment period. In both a bivariate analysis and a simple multivariate model, principal intoxicating substance is the strongest predictor of having a fixed abode both before and after treatment. However, a more sophisticated analysis indicates that socioeconomic resources and social capital play along with the preferred intoxicating substance as predictors of having permanent housing. After more than a decade of a housing-led national homeless policy, and wide embracement of Housing First approaches in the European Union, homeless persons entering specialised alcohol and drug treatment are likely to return to the streets and hostels at the end of treatment. Access to housing after treatment is very limited for those lacking resources to solve their housing problem without assistance

  2. Loading History Effect on Creep Deformation of Rock

    Directory of Open Access Journals (Sweden)

    Wendong Yang

    2018-06-01

    Full Text Available The creep characteristics of rocks are very important for assessing the long-term stability of rock engineering structures. Two loading methods are commonly used in creep tests: single-step loading and multi-step loading. The multi-step loading method avoids the discrete influence of rock specimens on creep deformation and is relatively time-efficient. It has been widely accepted by researchers in the area of creep testing. However, in the process of multi-step loading, later deformation is affected by earlier loading. This is a key problem in considering the effects of loading history. Therefore, we intend to analyze the deformation laws of rock under multi-step loading and propose a method to correct the disturbance of the preceding load. Based on multi-step loading creep tests, the memory effect of creep deformation caused by loading history is discussed in this paper. A time-affected correction method for the creep strains under multi-step loading is proposed. From this correction method, the creep deformation under single-step loading can be estimated by the super-position of creeps obtained by the dissolution of a multistep creep. We compare the time-affected correction method to the coordinate translation method without considering loading history. The results show that the former results are more consistent with the experimental results. The coordinate translation method produces a large error which should be avoided.

  3. The Comfort Houses : measurements and analysis of the indoor environment and energy consumption in 8 passive houses 2008-2011

    Energy Technology Data Exchange (ETDEWEB)

    Steen Larsen, T.; Lund Jensen, R.; Daniels, O.

    2012-01-15

    The report is prepared in relation to the project ''demonstration of energy consumption and indoor climate in 10 Danish passive houses'' which was carried out from 2008 to 2012 in the Comfort Houses. The report presents the achieved results based on measurements of indoor climate and energy consumption, and it also suggests viable solutions for the future low-energy buildings. The Comfort House project was started in 2007 as a development project at the company Saint Gobain Isover A/S, who wanted to disseminate knowledge about low-energy buildings and the principles behind them. The present report mainly focuses on the results from the Comfort Houses, but it also includes references to other Danish experimental buildings and development projects. Furthermore, the analyses are supplemented with experiences from Swedish low-energy buildings found through literature reviews. The indoor climate analyses deal with the different physical parameters that impact the residents. The evaluation includes both thermal, atmospheric, daylight and acoustic climate. The energy consumption is evaluated together with some of the key parameters from the houses that are related to the energy consumption. Finally, the residents' behaviour impacting both energy consumption and indoor climate are analysed. (LN)

  4. Assessment of circumferential cracks in hypereutectic Al-Si clutch housings

    Directory of Open Access Journals (Sweden)

    M. Haghshenas

    2017-04-01

    Full Text Available As in situ natural composites with silicon phase acting as the reinforcing phase, Al-Si alloys are among most commonly used aluminum alloys in automotive applications (i.e. engine component. Silicon contributes to the strength of Al-Si alloys through load transfer from the Al matrix to the hard (rigid Si phase in the microstructure (load-carrying capacity. Casting parameters (i.e. solidification rate, elemental segregation, secondary dendrite spacing… as well as the size and distribution of the microstructural constituents in Al-Si alloys (i.e. morphology of Si particles, intermetallic compounds, secondary dendrite spacing contribute directly to the mechanical response and failure (or fracture behavior of the alloy within the service. In hyper-eutectic Al-Si alloys (i.e. B390.0, distribution of coarse pre-eutectic Si particle mainly contribute to stress concentration, crack initiation and propagation during the actual service condition. In the present paper, the parameters contribution to the formation of the circumferential cracks in clutch housings made of die cast hyper-eutectics B390.0 Al-Si alloys are assessed through optical microscopy and scanning electron microscopy. Casting variable, cooling rate, their effect on the cracks as well some of the possible causes are also discussed in detail.

  5. Development of archetypes of building characteristics libraries for simplified energy use evaluation of houses

    Energy Technology Data Exchange (ETDEWEB)

    Parekh, A. [Natural Resources Canada, Ottawa, ON (Canada). CANMET Energy Technology Centre

    2005-07-01

    Simple energy analysis software is needed for quick and reliable energy evaluations. One of the key requirements for simplified units is the acquisition of default data for house geometry, equipment and thermal characteristics based on type and region in which the house is situated. This paper provided a summary of various house surveys and the document procedures used for developing archetype building characteristics libraries. Specific applications were described to demonstrate the viability of archetype libraries. Representative numerical approaches were applied to develop the archetype house characteristics using data gathered from the surveys of housing stock in Canada. Characteristics included size and type of house; the composition of envelope components; heating and hot water equipment data; airtightness and ventilation parameters; and base loads and operating conditions. The surveys were applied for developing a master spreadsheet. Information was collated and the criteria for correlating geometric and thermal characteristics were established. Various groupings of the data were assembled to arrive at representative thermal and performance values. Key parameters were verified with known reports from Statistics Canada, including foot print area; type of housing; local code requirements for the era of construction; primary fuels; and energy use indices. Parametric energy simulations were then performed to determine the sensitivity of various archetypes based on floor area and location, as well as vintage classification. The representative archetype of housing form included 3 components: (1) geometric configurations, (2) thermal characteristics, and (3) operating parameters. The viability of the archetypical defaults was validated by their application to the Energy Evaluations for the EnerGuide for House Program as well as in Housing Policy Analysis, and Tracking Energy Efficiency of Housing programs. It was concluded that the archetypical information about

  6. 25 solar houses single-family of promotion publishes in Cantimpalos (Segovia); 25 viviendas unifamilares solares de promocion publica en Cantimpalos (Segovia)

    Energy Technology Data Exchange (ETDEWEB)

    Yanez, G.

    2008-07-01

    We present in this article a set of social houses built in Sevogia for the Autonomous Administration of Castilla y Leon in which have been applied some bio climatic and passive techniques. In this communication are described the main architectural features and are exposed the energy saving calculated and some of the results obtained through monitoring. (Author)

  7. High power s-band vacuum load

    Energy Technology Data Exchange (ETDEWEB)

    Neubauer, Michael [Muons, Inc., Batavia, IL (United States); Dudas, Alan [Muons, Inc., Batavia, IL (United States); Krasnykh, Anatoly [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2016-12-29

    Through a combination of experimentation and calculation the components of a novel room temperature dry load were successfully fabricated. These components included lossy ceramic cylinders of various lengths, thicknesses, and percent of silicon carbide (SiC). The cylinders were then assembled into stainless steel compression rings by differential heating of the parts and a special fixture. Post machining of this assembly provided a means for a final weld. The ring assemblies were then measured for S-parameters, individually and in pairs using a low-cost TE10 rectangular to TE01 circular waveguide adapter specially designed to be part of the final load assembly. Matched pairs of rings were measured for assembly into the final load, and a sliding short designed and fabricated to assist in determining the desired short location in the final assembly. The plan for the project was for Muons, Inc. to produce prototype loads for long-term testing at SLAC. The STTR funds for SLAC were to upgrade and operate their test station to ensure that the loads would satisfy their requirements. Phase III was to be the sale to SLAC of loads that Muons, Inc. would manufacture. However, an alternate solution that involved a rebuild of the old loads, reduced SLAC budget projections, and a relaxed time for the replacement of all loads meant that in-house labor will be used to do the upgrade without the need for the loads developed in this project. Consequently, the project was terminated before the long term testing was initiated. However, SLAC can use the upgraded test stand to compare the long-term performance of the ones produced in this project with their rebuilt loads when they are available.

  8. High power s-band vacuum load

    International Nuclear Information System (INIS)

    Neubauer, Michael; Dudas, Alan; Krasnykh, Anatoly

    2016-01-01

    Through a combination of experimentation and calculation the components of a novel room temperature dry load were successfully fabricated. These components included lossy ceramic cylinders of various lengths, thicknesses, and percent of silicon carbide (SiC). The cylinders were then assembled into stainless steel compression rings by differential heating of the parts and a special fixture. Post machining of this assembly provided a means for a final weld. The ring assemblies were then measured for S-parameters, individually and in pairs using a low-cost TE10 rectangular to TE01 circular waveguide adapter specially designed to be part of the final load assembly. Matched pairs of rings were measured for assembly into the final load, and a sliding short designed and fabricated to assist in determining the desired short location in the final assembly. The plan for the project was for Muons, Inc. to produce prototype loads for long-term testing at SLAC. The STTR funds for SLAC were to upgrade and operate their test station to ensure that the loads would satisfy their requirements. Phase III was to be the sale to SLAC of loads that Muons, Inc. would manufacture. However, an alternate solution that involved a rebuild of the old loads, reduced SLAC budget projections, and a relaxed time for the replacement of all loads meant that in-house labor will be used to do the upgrade without the need for the loads developed in this project. Consequently, the project was terminated before the long term testing was initiated. However, SLAC can use the upgraded test stand to compare the long-term performance of the ones produced in this project with their rebuilt loads when they are available.

  9. Droop Control of Solar PV, Grid and Critical Load using Suppressing DC Current Injection Technique without Battery Storage

    Science.gov (United States)

    Dama Mr., Jayachandra; (Mrs. , Lini Mathew, Dr.; Srikanth Mr., G.

    2017-08-01

    This paper presents design of a sustainable solar Photo voltaic system for an Indian cities based residential/community house, integrated with grid, supporting it as supplementary sources, to meet energy demand of domestic loads. The role of renewable energy sources in Distributed Generation (DG) is increasingly being recognized as a supplement and an alternative to large conventional central power supply. Though centralized economic system that solely depends on cities is hampered due to energy deficiency, the use of solar energy in cities is never been tried widely due to technical inconvenience and high installation cost. To mitigate these problems, this paper proposes an optimized design of grid-tied PV system without storage which is suitable for Indian origin as it requires less installallation cost and supplies residential loads when the grid power is unavailable. The energy requirement is mainly fulfilled from PV energy module for critical load of a city located residential house and supplemented by grid/DG for base and peak load. The system has been developed for maximum daily household demand of 50kWp and can be scaled to any higher value as per requirement of individual/community building ranging from 50kWp to 60kWp as per the requirement. A simplified control system model has been developed to optimize and control flow of power from these sources. The simulation work, using MATLAB Simulink software for proposed energy management, has resulted in an optimal yield leading efficient power flow control of proposed system.

  10. In-house zinc SAD phasing at Cu Kα edge.

    Science.gov (United States)

    Kim, Min-Kyu; Lee, Sangmin; An, Young Jun; Jeong, Chang-Sook; Ji, Chang-Jun; Lee, Jin-Won; Cha, Sun-Shin

    2013-07-01

    De novo zinc single-wavelength anomalous dispersion (Zn-SAD) phasing has been demonstrated with the 1.9 Å resolution data of glucose isomerase and 2.6 Å resolution data of Staphylococcus aureus Fur (SaFur) collected using in-house Cu Kα X-ray source. The successful in-house Zn-SAD phasing of glucose isomerase, based on the anomalous signals of both zinc ions introduced to crystals by soaking and native sulfur atoms, drove us to determine the structure of SaFur, a zinc-containing transcription factor, by Zn-SAD phasing using in-house X-ray source. The abundance of zinc-containing proteins in nature, the easy zinc derivatization of the protein surface, no need of synchrotron access, and the successful experimental phasing with the modest 2.6 Å resolution SAD data indicate that inhouse Zn-SAD phasing can be widely applicable to structure determination.

  11. House Price, House Quality and Economic Growth

    NARCIS (Netherlands)

    De Vries, P.; Boelhouwer, P.J.

    2010-01-01

    The literature on housing markets suggest that periods of economic growth are characterised by a demand for better housing quality and increasing prices. The basic principles of the theory are that the short-run price fluctuations occur due to market imperfection, while over the long term, causality

  12. Predictors of homeless services re-entry within a sample of adults receiving Homelessness Prevention and Rapid Re-Housing Program (HPRP) assistance.

    Science.gov (United States)

    Brown, Molly; Vaclavik, Danielle; Watson, Dennis P; Wilka, Eric

    2017-05-01

    Local and national evaluations of the federal Homelessness Prevention and Rapid Re-Housing Program (HPRP) have demonstrated a high rate of placement of program participants in permanent housing. However, there is a paucity of research on the long-term outcomes of HPRP, and research on rehousing and prevention interventions for single adults experiencing homelessness is particularly limited. Using Homeless Management Information System data from 2009 to 2015, this study examined risk of return to homeless services among 370 permanently housed and 71 nonpermanently housed single adult HPRP participants in Indianapolis, Indiana. Kaplan-Meier survival curves were conducted to analyze time-to-service re-entry for the full sample, and the homelessness prevention and rapid rehousing participants separately. With an average follow-up of 4.5 years after HPRP exit, 9.5% of the permanently housed HPRP participants and 16.9% of those nonpermanently housed returned to homeless services. By assistance type, 5.4% of permanently housed and 15.8% of nonpermanently housed homelessness prevention recipients re-entered services, and 12.8% of permanently housed and 18.2% of nonpermanently housed rapid rehousing recipients re-entered during the follow-up period. Overall, veterans, individuals receiving rapid rehousing services, and those whose income did not increase during HPRP had significantly greater risk of returning to homeless services. Veterans were at significantly greater risk of re-entry when prevention and rehousing were examined separately. Findings suggest a need for future controlled studies of prevention and rehousing interventions for single adults, aiming to identify unique service needs among veterans and those currently experiencing homelessness in need of rehousing to inform program refinement. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  13. Livable Housing Design: The voluntary provision of inclusive housing in Australia

    Directory of Open Access Journals (Sweden)

    Margaret Louise Ward

    2014-06-01

    Full Text Available This paper reports on a study of the voluntary provision of inclusive housing. The impetus for the study is the Livable Housing Design initiative, an agreement among Australian housing industry and community leaders in 2010 to a national guideline and voluntary strategy with a target to provide minimum access features in all new housing by 2020. Situated in and around Brisbane, Australia, the study problematises the assumption that the housing industry will respond voluntarily; an assumption which this study concludes is unfounded. The Livable Housing Design initiative asks individual agents to consider the needs of people beyond the initial contract, to proceed with objective reasoning and to do the right thing voluntarily. Instead, the study found that interviewees focused on their immediate contractual obligations, were reluctant to change established practices and saw little reason to do more than was legally required of them. This paper argues that the highly-competitive and risk-averse nature of the industry works against a voluntary approach for inclusive housing and, if the 2020 target of the Livable Housing Design.

  14. Tech House

    Science.gov (United States)

    1978-01-01

    The members of the Swain family- Dr. Charles "Bill" Swain, wife Elaine, daughter Carol, 17, son "Chuck", 12, and dog Susie have an interesting assignment. They are active participants in an important NASA research program involving the application of space-age technology to home construction. b' Transplanted Floridians, the Swains now reside in NASA's Tech House, loatedat Langley Research Center, Hampton, Virginia. Their job is to use and help evaluate the variety of advanced technology systems in Tech House. A contemporary three-bedroom home, Tech House incorporates NASA technology, the latest commercial building techniques and other innovations, all designed to reduce energy and water consumption and to provide new levels of comfort, convenience, security and fire safety. Tech House equipment performed well in initial tests, but a house is not a home until it has people. That's where the Swains come in. NASA wants to see how the various systems work under actual living conditions, to confirm the effectiveness of the innovations or to determine necessary modifications for improvement. The Swains are occupying the house for a year, during which NASA engineers are computer monitoring the equipment and assembling a record of day-to-day performance. . Tech House is a laboratory rather than a mass production prototype, but its many benefits may influence home design and construction. In a period of sharply rising utility costs, widespread adoption of Tech House features could provide large-scale savings to homeowners and potentially enormous national benefit in resources conservation. Most innovations are aerospace spinoffs: Some of the equipment is now commercially available; other systems are expected to be in production within a few years. Around 1980, a Tech House-type of home could be built for $45-50,000 (1 976 dollars). It is estimated that the homeowner would save well over $20,000 (again 1976 dollars) in utility costs over the average mortgage span of 20 years.

  15. The Special Importance of Housing Policy for the Housing Situation of Ethnic Minorities

    DEFF Research Database (Denmark)

    Andersen, Hans Skifter; Magnusson Turner, Lena; Søholt, Susanne

    The purpose of this article is to uncover, whether housing policy has a special importance for immigrants, compared with the whole population, by comparing housing policies and immigrants’ housing outcomes in four Nordic countries: Denmark, Finland, Norway and Sweden. There are substantial...... population varies much. These differences can only to some extent be explained by income inequalities on the housing markets in the countries, inequalities that affect immigrants. Other important explanations of why immigrants perform worse on the housing market is the shortage of rental housing (Norway......’ housing options are strict needs test for social/public housing (Finland)....

  16. The Special Importance of Housing Policy for the Housing Situation of Ethnic Minorities

    DEFF Research Database (Denmark)

    Andersen, Hans Skifter; Turner, Lena Magnusson; Søholt, Susanne

    2013-01-01

    The purpose of this article is to uncover, whether housing policy has a special importance for immigrants, compared with the whole population, by comparing housing policies and immigrants’ housing outcomes in four Nordic countries: Denmark, Finland, Norway and Sweden. There are substantial...... population varies much. These differences can only to some extent be explained by income inequalities on the housing markets in the countries, inequalities that affect immigrants. Other important explanations of why immigrants perform worse on the housing market is the shortage of rental housing (Norway......’ housing options are strict needs test for social/public housing (Finland)....

  17. Scattered housing energy retrofit program : final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-11-15

    Between 1999 and 2006, home energy audits were conducted in 770 scattered houses belonging to the Toronto Community Housing Corporation (TCHC). Over the course of the project, 126 houses were retrofitted with energy saving measures based on calculations of the most cost-effective measures. This report outlined the work that was conducted by the contractor, GreenSaver over the course of the project. The report discussed the project players and project execution. It included a profile of audited houses; auditing procedure; house reports; retrofit work; contractor arranging service; and post-retrofit inspections. Comments on retrofit work not carried out were also provided. The report also discussed the results of the project, including energy savings and emission reductions and participant feedback. A summary of the energy efficiency retrofit survey was also presented along with lessons learned. These included the availability of a contingency fund; the importance of tenant involvement; and making arrangements for other repair work. It was concluded that the amount of expected energy savings on space heating bills varied from house to house, and fell between 15 and 74 per cent. The report recommended that tenants and staff in the social housing sector could benefit from a greater awareness of energy issues and its more efficient use, allowing even greater and longer lasting benefits from a project like this. 8 tabs.

  18. Indoor air quality in the Swedish housing stock and its dependence on building characteristics

    DEFF Research Database (Denmark)

    Langer, Sarka; Bekö, Gabriel

    2013-01-01

    .47h-1). The majority of houses (80%) did not comply with the building code that requires 0.5 air changes per hour. The median concentrations in single-family houses and apartments were 6.0 and 10μg/m3, respectively, for NO2, 22 and 13μg/m3 for formaldehyde, and 236 and 143μg/m3 for TVOC. All......Data from a recent Swedish survey on the status of the housing stock and indoor air quality were placed in the public domain by the Swedish National Board of Housing, Building and Planning in 2011. The available parameters included the year of construction, dwelling location, type of ventilation...

  19. Impacts of the Weatherization Assistance Program in Fuel-Oil Heated Houses

    Energy Technology Data Exchange (ETDEWEB)

    Levins, W.P.

    1994-01-01

    In 1990, the U.S. Department of Energy (DOE) initiated a national evaluation of its low-income Weatherization Assistance Program. This report, which is one of five parts of that evaluation, evaluates the energy savings and cost-effectiveness of the Program as it had been applied to single-family houses heated primarily by fuel-oil. The study was based upon a representative sample (41 local weatherization agencies, 222 weatherized and 115 control houses) from the nine northeastern states during 1991 and 1992 program years. Dwelling-specific and agency-level data on measures installed, costs, and service delivery procedures were collected from the sampled agencies. Space-heating fuel-oil consumption, indoor temperature, and outdoor temperature were monitored at each house. Dwelling characteristics, air-leakage measurements, space-heating system steady-state efficiency measurements, safety inspections, and occupant questionnaires were also collected or performed at each monitored house. We estimate that the Program weatherized a total of 23,400 single-family fuel-oil heated houses in the nine northeastern states during program years 1991 and 1992. Annual fuel-oil savings were calculated using regression techniques to normalize the savings to standard weather conditions. For the northeast region, annual net fuel-oil savings averaged 160 gallons per house, or 17.7% of pre-weatherization consumption. Although indoor temperatures changed in individual houses following weatherization, there was no average change and no significant difference as compared to the control houses; thus, there was no overall indoor temperature takeback effect influencing fuel-oil savings. The weatherization work was performed cost effectively in these houses from the Program perspective, which included both installation costs and overhead and management costs but did not include non-energy benefits (such as employment and environmental). Total average costs were $1819 per house ($1192 for

  20. Load research manual. Volume 1. Load research procedures

    Energy Technology Data Exchange (ETDEWEB)

    Brandenburg, L.; Clarkson, G.; Grund, Jr., C.; Leo, J.; Asbury, J.; Brandon-Brown, F.; Derderian, H.; Mueller, R.; Swaroop, R.

    1980-11-01

    This three-volume manual presents technical guidelines for electric utility load research. Special attention is given to issues raised by the load data reporting requirements of the Public Utility Regulatory Policies Act of 1978 and to problems faced by smaller utilities that are initiating load research programs. In Volumes 1 and 2, procedures are suggested for determining data requirements for load research, establishing the size and customer composition of a load survey sample, selecting and using equipment to record customer electricity usage, processing data tapes from the recording equipment, and analyzing the data. Statistical techniques used in customer sampling are discussed in detail. The costs of load research also are estimated, and ongoing load research programs at three utilities are described. The manual includes guides to load research literature and glossaries of load research and statistical terms.