WorldWideScience

Sample records for single wood type

  1. Wood construction and magnetic characteristics of impregnated type magnetic wood

    International Nuclear Information System (INIS)

    Oka, Hideo; Hojo, Atsushi; Seki, Kyoushiro; Takashiba, Toshio

    2002-01-01

    The results of experiments involving the AC and DC magnetic characteristics of impregnated type magnetic wood were studied by taking into consideration the wood construction and fiber direction. The experimental results show that the sufficient amount of impregnated magnetic fluid varies depending on the fiber direction and length, and the grain face of the wood material. The impregnated type magnetic wood sample that is fully impregnated by magnetic fluid has a 60% saturation magnetization compared to the saturation magnetization of magnetic fluid. Samples for which the wood fiber direction was the same as the direction of the magnetic path had a higher magnetization intensity and permeability

  2. Impact of KCl impregnation on single particle combustion of wood and torrefied wood

    DEFF Research Database (Denmark)

    Lu, Zhimin; Jian, Jie; Jensen, Peter Arendt

    2017-01-01

    In this work, single particle combustion of raw and torrefied 4 mm wood particles with different potassium content obtained by KCl impregnation and washing was studied experimentally under a condition of 1225 °C, 3.1% O2 and 26.1% H2O. The ignition time and devolatilization time depended almost......, and unchanged by torrefaction. Compared to the raw wood particle, the char conversion time was increased by torrefaction, decreased by washing, and almost unchanged by KCl impregnation due to its promoting effect on both char yield and reactivity....

  3. Influence of Torrefaction on Single Particle Combustion of Wood

    DEFF Research Database (Denmark)

    Lu, Zhimin; Jian, Jie; Jensen, Peter Arendt

    2016-01-01

    This study focuses on the influence of torrefaction on the char reactivity, char yield, and combustion time of 3-5 mm spherical wood particles in a single particle combustion reactor (SPC) operating at a nominal temperature of 1231 °C. The devolatilization times were reduced and the char burnout...

  4. Study of types of defects in wood chipboard production

    OpenAIRE

    Vasendina, Elena Aleksandrovna; Plotnikova, Inna Vasilievna; Redko, Lyudmila Anatolevna; Zyablova, Natalia Nikolaevna

    2015-01-01

    Types of defects in wood chipboard production and losses connected with the defects were studied. Faulty products were studied by statistical methods of control; analysis of causes of faulty products at wood chipboards production was carried out. Economical appraisal of losses according to peculiarities of production was given.

  5. Characterization of novolac type liquefied wood/phenol/formaldehyde (LWPF) resin

    Science.gov (United States)

    Hui Pan; Todd F. Shupe; Chung-Yun Hse

    2009-01-01

    Novolac type liquefied wood/phenol/formaldehyde (LWPF) resins were synthesized from liquefied wood and formaldehyde. The average molecular weight of the LWPF resin made from the liquefied wood reacted in an atmospheric three neck flask increased with increasing P/W ratio. However, it decreased with increasing phenol/wood ratio when using a sealed Parr reactor. On...

  6. Emission characteristics of modern and old-type residential boilers fired with wood logs and wood pellets

    Science.gov (United States)

    Johansson, Linda S.; Leckner, Bo; Gustavsson, Lennart; Cooper, David; Tullin, Claes; Potter, Annika

    Emissions from commercial residential boilers fired with wood logs and wood pellets, have been compared. Seven boilers, selected with respect to age, design, connection to heat storage tank, and type of biofuel, were included in the study, which also covers two oil-fired boilers in comparison. The measurements of gaseous emissions comprised carbon monoxide (CO), carbon dioxide (CO 2), oxygen (O 2), total organic carbons (TOC), nitrogen oxides (NO x), polycyclic aromatic hydrocarbons (PAH), and 33 volatile organic compounds (VOC). Particle emissions were characterised by mass concentration, number concentration, and the corresponding particle size distributions. In general, old-type wood boilers caused considerably higher emissions than modern wood and pellet boilers. The mass concentration of particles was 180 times larger in the worst old-type case (a water-cooled wood boiler without heat storage tank) compared to the best modern case (wood pellets). The TOC emission was shown to be correlated to the CO emission, both ranging between very low values and up to 10 000 mg/MJ, depending on design and operation. The highest emissions of unoxidised compounds occurred at the highest excess air ratio, and oxygen was not the limiting parameter for poor combustion. Instead, high excess air can be suspected to cool the combustion chamber, resulting in high CO emissions. VOC was dominated by methane. Especially from an old-type boiler the methane emissions could be high and the effect on climate change then may become larger than that of an oil boiler. However, substitution of an old-type wood boiler with a modern wood boiler attached to a storage tank or with a pellet boiler, would reduce methane emissions by 8 to 9000 times and the efficiency would increase. Most emissions could be considerably lowered by connecting the old-type wood boiler to a heat storage tank, or by charging small (in relation to the combustion chamber) batches of wood.

  7. Wood

    DEFF Research Database (Denmark)

    Unterrainer, Walter

    2014-01-01

    come from? How is it harvested? How is it manufactured and treated ? How are the buildings detailed and protected against weather during construction to keep them dry and make them long-life ? In a period of climate change, forests are the last lungs of the planet to sequestrate CO2. Their global size......Wood – a sustainable building material ? For thousands of years and all over the planet, wood has been used as a building material and exciting architecture has been created in wood. The fantastic structural, physical and aesthetic properties of the material as well as the fact that wood...... is a renewable resource makes it predestinated for what is considered ´sustainable architecture´. But the reality is less linear and there are serious traps: In fact the lecture shows by examples that it is much easier to build very unsustainable buildings in wood than the other way round! Where does the wood...

  8. Comperative Study of Woods Type to the Smoked Catfish (Pangasius Hypopthalmus) Flavour

    OpenAIRE

    Yuliandri, Ade; ', Syahrul; ', Dahlia

    2014-01-01

    This study was intended to evaluate the quality of smoked catfish smoked withdifferent types of woods. The fish weighing 250-300gr each were smoked with hot andliquid smoking method using rambutan wood (Nephelium lappacium) and medang wood(Dcinamouns spp). The smoked catfishes were evaluated for sensory quality, moisture, fenolvalue, acid value and pH. The smoked catfishes which were smoked with rambutan woodwere compared to that smoked with medang wood. The results showed that the smokedcatf...

  9. Modelling of flash pyrolysis of a single wood particle.

    NARCIS (Netherlands)

    Janse, A.M.C.; Janse, A.M.C.; Westerhout, R.W.J.; Westerhout, R.W.J.; Prins, W.

    2000-01-01

    Reactors for flash pyrolysis of biomass are designed to maximize the yield of bio-oil, at the expense of the by-products gas and char. To understand which chemical and physical factors influence the yield to bio-oil, the flash pyrolysis of a cylindrical wood particle with a maximum diameter of 1000

  10. Wood

    Science.gov (United States)

    David W. Green; Robert H. White; Antoni TenWolde; William Simpson; Joseph Murphy; Robert J. Ross; Roland Hernandez; Stan T. Lebow

    2006-01-01

    Wood is a naturally formed organic material consisting essentially of elongated tubular elements called cells arranged in a parallel manner for the most part. These cells vary in dimensions and wall thickness with position in the tree, age, conditions of growth, and kind of tree. The walls of the cells are formed principally of chain molecules of cellulose, polymerized...

  11. Effects of heat treatment of wood on hydroxylapatite type mineral precipitation and biomechanical properties in vitro.

    Science.gov (United States)

    Rekola, J; Lassila, L V J; Hirvonen, J; Lahdenperä, M; Grenman, R; Aho, A J; Vallittu, P K

    2010-08-01

    Wood is a natural fiber reinforced composite. It structurally resembles bone tissue to some extent. Specially heat-treated birch wood has been used as a model material for further development of synthetic fiber reinforced composites (FRC) for medical and dental use. In previous studies it has been shown, that heat treatment has a positive effect on the osteoconductivity of an implanted wood. In this study the effects of two different heat treatment temperatures (140 and 200 degrees C) on wood were studied in vitro. Untreated wood was used as a control material. Heat treatment induced biomechanical changes were studied with flexural and compressive tests on dry birch wood as well as on wood after 63 days of simulated body fluid (SBF) immersion. Dimensional changes, SBF sorption and hydroxylapatite type mineral formation were also assessed. The results showed that SBF immersion decreases the biomechanical performance of wood and that the heat treatment diminishes the effect of SBF immersion on biomechanical properties. With scanning electron microscopy and energy dispersive X-ray analysis it was shown that hydroxylapatite type mineral precipitation formed on the 200 degrees C heat-treated wood. An increased weight gain of the same material during SBF immersion supported this finding. The results of this study give more detailed insight of the biologically relevant changes that heat treatment induces in wood material. Furthermore the findings in this study are in line with previous in vivo studies.

  12. Wood particleboard and flakeboard : types, grades, and uses

    Science.gov (United States)

    C. G. Carll

    1986-01-01

    This report is for those who use or may want to use wood particleboard. The term bparticleboardc is used as defined in the American Society for Testing and Materials (ASTM) Standard D 1554, which includes flakeboards as a subclass of particleboards, and not as used in the lumber trade where the term is usually reserved for panels made of fine wood particles such as...

  13. Mathematical modelling of the combustion of a single wood particle

    Energy Technology Data Exchange (ETDEWEB)

    Porteiro, J.; Miguez, J.L.; Granada, E.; Moran, J.C. [Departamento de Ingenieria Mecanica, Maquinas y Motores Termicos y Fluidos. Universidad de Vigo, Lagoas Marcosende 9 36200 Vigo (Spain)

    2006-01-15

    A mathematical model describing the thermal degradation of densified biomass particles is presented here. The model uses a novel discretisation scheme and combines intra-particle combustion processes with extra-particle transport processes, thereby including thermal and diffusional control mechanisms. The influence of structural changes on the physical-thermal properties of wood in its different stages is studied together with shrinkage of the particle during its degradation. The model is used to compare the predicted data with data on the mass loss dynamics and internal temperature of several particles from previous works and relevant literature, with good agreement. (author)

  14. Influence of soy type on wood bonding performance

    Science.gov (United States)

    Charles R. Frihart

    2011-01-01

    Proteins were the main wood bonding adhesives for centuries, but they were displaced by fossil fuel-based adhesives in the 20th century because synthetic adhesives offered better water resistance, ease of use, and lower cost. Recently, studies using a polyamidoamine– epichlorohydrin (PAE) curing agent have led to soybean-based adhesives that are...

  15. Cellulolytic activities of wild type fungi isolated from decayed wood ...

    African Journals Online (AJOL)

    Abstract. The mycological profile of decayed wood cuttings sourced from a saw mill located at Uwasota Road, Benin City was investigated using serial dilution and pour plate techniques. The mean fungal counts ranged from 0.9 ×106 cfu/g to 2.7 ×106 cfu/g respectively. Four fungal species were identified; Aspergillus niger, ...

  16. Effect of wood type and thickness on acetification kinetics in traditional vinegar production

    Directory of Open Access Journals (Sweden)

    Maria-Jesús Torija

    2009-04-01

    Full Text Available Maria-Jesús Torija1, Estibaliz Mateo1, Carlos-Alfredo Vegas1, Carla Jara1, Angel González1, Montse Poblet1, Cristina Reguant1, Jóse-Manuel Guillamon2, Albert Mas11Biotecnología enológica. Departament de Bioquímica i Biotecnologia, Facultat d’enologia, Universitat Rovira i Virgili, Tarragona, Spain; 2Departamento de Biotecnología de los Alimentos, Instituto de Agroquímica y Tecnología de Alimentos (CSIC, Burjassot, València, SpainAbstract: Traditional vinegar production is a lengthy process which implies high operational risks and jeopardizes the organoleptic characteristics of the final product. In an effort to solve these problems without changing the traditional model, we modified the wood type and thickness of vinegar barrels. We acetified in triplicate in barrels made of acacia, cherry, chestnut, and oak and in three wood thicknesses (15, 20, and 25 mm in two different vinegar plants. The operating volume was set at 60 L. Reducing wood thickness improved neither maximum acetification velocity or the total length of the process, and in some cases even worsened them. The process took longer in oak barrels than in other types of wood barrel in one of the vinegar plants. Therefore, the choice of wood is a parameter to be considered in the wine vinegar production. Keywords: acacia, cherry, chestnut, oak, acetic acid bacteria

  17. Effect of silvicultural practice and wood type on loblolly pine particleboard and medium density fiberboard properties

    Science.gov (United States)

    Todd F. Shupe; Chung Y. Hse; Elvin T. Choong; Leslie H.. Groom

    1999-01-01

    he objective of this study was to determine the effect of five different silvicultural strategies and wood type on mechanical and physical properties of loblolly pine (Pinus taeda L.) particleboard and fiberboard. The furnish was prepared in an unconventional manner from innerwood and outerwood veneer for each stand. Modulus of rupture (MOR)...

  18. Determining stocks and flows of structural wood products in single family homes in the United States between 1950 and 2010

    DEFF Research Database (Denmark)

    Sianchuk, Robert A.; McFarlane, Paul N.; Ackom, Emmanuel

    2012-01-01

    The stocks and flows of six major structural wood products (SWPs)-lumber, plywood, oriented strand board [OSB], glue laminated timber, I-joists, and laminated veneer lumber (LVL)-in US single family homes were modeled from 1950 to 2010. The consumption of these products in US single family homes...

  19. Determination of bending moment resistance of t-type joints constructed with wood biscuit

    Directory of Open Access Journals (Sweden)

    Mohammad Kahvand

    2014-11-01

    Full Text Available The goal of this study was to investigate effects of wood species (Beech and Fir, number of connectors (1 and 2, size of biscuit (10 and 20 and type of adhesives (Polyvinyl acetate (PVAc, polyurethane (PU and urea-formaldehyde (UF on bending moment resistance of joints fabricated with biscuit. Results have shown that member of joint, number of connector, size of biscuit and type of adhesive had significant effect on the bending moment resistance. Bending moment resistance of joints made of Beech wood were stronger than joints made of Fir ones. Bending moment resistance has increased, with the increase of size and number of biscuit. Performance of joints with PU adhesive had better than PVA and UF. Highest bending moment resistance were obtained from joints glued with PU adhesive, size of biscuit 20 and 2 connectors. The results also indicated that joints made with biscuit and glued with PU had higher resistance than wooden dowel joints.

  20. Choosing Wood Burning Appliances

    Science.gov (United States)

    Information to assist consumers in choosing a wood burning appliance, including types of appliances, the differences between certified and non-certified appliances, and alternative wood heating options.

  1. Odor, gaseous and PM10 emissions from small scale combustion of wood types indigenous to Central Europe

    Science.gov (United States)

    Kistler, Magdalena; Schmidl, Christoph; Padouvas, Emmanuel; Giebl, Heinrich; Lohninger, Johann; Ellinger, Reinhard; Bauer, Heidi; Puxbaum, Hans

    2012-05-01

    In this study, we investigated the emissions, including odor, from log wood stoves, burning wood types indigenous to mid-European countries such as Austria, Czech Republic, Hungary, Slovak Republic, Slovenia, Switzerland, as well as Baden-Württemberg and Bavaria (Germany) and South Tyrol (Italy). The investigations were performed with a modern, certified, 8 kW, manually fired log wood stove, and the results were compared to emissions from a modern 9 kW pellet stove. The examined wood types were deciduous species: black locust, black poplar, European hornbeam, European beech, pedunculate oak (also known as “common oak”), sessile oak, turkey oak and conifers: Austrian black pine, European larch, Norway spruce, Scots pine, silver fir, as well as hardwood briquettes. In addition, “garden biomass” such as pine cones, pine needles and dry leaves were burnt in the log wood stove. The pellet stove was fired with softwood pellets. The composite average emission rates for log wood and briquettes were 2030 mg MJ-1 for CO; 89 mg MJ-1 for NOx, 311 mg MJ-1 for CxHy, 67 mg MJ-1 for particulate matter PM10 and average odor concentration was at 2430 OU m-3. CO, CxHy and PM10 emissions from pellets combustion were lower by factors of 10, 13 and 3, while considering NOx - comparable to the log wood emissions. Odor from pellets combustion was not detectable. CxHy and PM10 emissions from garden biomass (needles and leaves) burning were 10 times higher than for log wood, while CO and NOx rise only slightly. Odor levels ranged from not detectable (pellets) to around 19,000 OU m-3 (dry leaves). The odor concentration correlated with CO, CxHy and PM10. For log wood combustion average odor ranged from 536 OU m-3 for hornbeam to 5217 OU m-3 for fir, indicating a considerable influence of the wood type on odor concentration.

  2. Plant single-cell and single-cell-type metabolomics.

    Science.gov (United States)

    Misra, Biswapriya B; Assmann, Sarah M; Chen, Sixue

    2014-10-01

    In conjunction with genomics, transcriptomics, and proteomics, plant metabolomics is providing large data sets that are paving the way towards a comprehensive and holistic understanding of plant growth, development, defense, and productivity. However, dilution effects from organ- and tissue-based sampling of metabolomes have limited our understanding of the intricate regulation of metabolic pathways and networks at the cellular level. Recent advances in metabolomics methodologies, along with the post-genomic expansion of bioinformatics knowledge and functional genomics tools, have allowed the gathering of enriched information on individual cells and single cell types. Here we review progress, current status, opportunities, and challenges presented by single cell-based metabolomics research in plants. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. Comparative study on the physico-mechanical characteristics for five types of wood flooring

    Directory of Open Access Journals (Sweden)

    Gabriela CĂLĂTAN

    2014-12-01

    Full Text Available During the period 1600-1700, the first works with parquet elements at Versailles Palace were performed, but the high cost has made that the wooden floor to be an exclusivist product for a long time. Currently, in the last 30 years, the most innovations in flooring industry were aimed to improve the technological process, the easing of work, to reduce the losses of raw materials and to reduce the production costs. The experimental research conducted worldwide has shown that the wood processing technology, up to the flooring finite element, plays an important role in achieving a superior quality and durability and that the finishing systems have to be applied depending on the conditions of the area of use. This paper is a comparative study regarding the physico-mechanical characteristics for five types of wood flooring manufactured and marketed in Romania. In the experimental research, there were analyzed: the behavior of the floor assemblies under linearly distributed and concentrated loads, the thermal insulation characteristics and the slip resistance. The experimental results have shown that these characteristics are influenced by the wood species, the type of product (massive one or subjected to stratification technological processing, the thickness of lamellar flooring elements, and the chosen finishing method (varnishing, oiling.

  4. Effects of tanalith-e impregnation substance on bending strengths and modulus of elasticity in bending of some wood types

    Directory of Open Access Journals (Sweden)

    Hakan Keskin

    2016-04-01

    Full Text Available The aim of this study was to investigate the effects of impregnation with Tanalith-E on the bending strengths and modulus of elasticity in bending of some wood types. The test samples prepared from beech, oak, walnut, poplar, ash and pine wood materials - that are of common use in the forest products industry of TURKEY - according to TS 345, were treated with according to ASTM D 1413-76 substantially. Un-impregnated samples according to impregnated wood materials, the bending strengths in beech to 6.83%, 5.12% in ash, 5.93% in pine, the elasticity module values to 7.15% in oak and ash, at a rate of 6.58% in the higher were found. The highest values of bending strengths and modulus of elasticity in bending were obtained in beech and ash woods impregnated with Tanalith-E, whereas the lowest values were obtained in the poplar wood.

  5. Fireplace and woodstove fine particle emissions from combustion of western Mediterranean wood types

    Science.gov (United States)

    Alves, Célia; Gonçalves, Cátia; Fernandes, Ana Patrícia; Tarelho, Luís; Pio, Casimiro

    2011-08-01

    Wood from seven species of trees grown in the Portuguese forest ( Pinus pinaster, Eucalyptus globulus, Quercus suber, Acacia longifolia, Quercus faginea, Olea europea and Quercus ilex rotundifolia), and briquettes produced from forest biomass waste were burned in a fireplace and in a woodstove to determine the chemical composition of fine particle (PM 2.5) emissions. Samples were analysed for organic and elemental carbon (OC/EC), water soluble ions (Na +, NH 4+, K +, Mg 2+, Ca 2+, Cl -, NO 3- and SO 42-) and 67 elements. The PM 2.5 emission factors (g kg - 1 fuel burned, dry basis) were in the ranges 9.9-20.2 and 4.2-16.3, respectively, for the fireplace and the woodstove. Organic carbon contributed to about 50% of the fine particle mass in the emissions from every wood species studied in both burning appliances. The carbonaceous component of PM 2.5 was dominated by organic carbon, accounting for more than 85% of the total carbon (TC): OC/TC ranged from 0.85 to 0.96 (avg. 0.92) for the fireplace and from 0.86 to 0.97 (avg. 0.93) for the woodstove. The water-soluble ions accounted for 0.64 to 11.3% of the PM 2.5 mass emitted from the fireplace, whereas mass fractions between 0.53 and 13.6% were obtained for the woodstove. The golden wattle wood smoke showed a much higher ionic content than the emissions from the other wood types. Trace elements represented 0.4 to 2.5% and 0.2 to 2.2% of the PM 2.5 mass emitted, respectively, from the fireplace and the woodstove, which corresponded to average total emissions of 132 ± 77.3 mg kg - 1 and 93.4 ± 60.8 mg kg - 1 of wood burned. Among these, K, Pb, Al, Mn and Sr were present in all samples. From the emission profiles of the individual experiments, composite wood combustion profiles are suggested with the aid of a cluster analysis.

  6. Influence of Small Furnaces Construction Type on TSP Emissions During Wood and Brown Coal Combustion

    Directory of Open Access Journals (Sweden)

    Jiří HORÁK

    2011-06-01

    Full Text Available Solid fuel burning household heat sources are considered to be significant producers of total suspended particulates (TSP. In the year 2005, c. 35% of the total particulate matter emissions PM10 (in The Czech Republic came out from household heating [1]. However, low-power combustion devices cannot be considered as identical pollution sources because they can operate on different combustion principles and feature dramatically different emission factors. The article presents results of an experimental determination of particulate matter emissions including TSP dividing into PM10 and PM2.5 fractions from wood and brown coal combustion in five types of combustion devices.

  7. Using the Resistograph®to distinguish different types of wood rot on living silver fir in Molise (Italy

    Directory of Open Access Journals (Sweden)

    Lasserre B

    2010-10-01

    Full Text Available he study was performed in two silver-fir forests (Abies alba Mill. located in Alto Molise, Province of Isernia: Collemeluccio, near Pescolanciano and Abeti Soprani near Capracotta. The aim of this work was to distinguish different types of wood rot on living silver fir individuals by using the Resistograph® (IML-RESI E400, a device that allows to estimate the variation of wood density by measuring the resistance to micro-perforation. The occurrence of different types of wood rot (white rot and brown rot in living trees was pointed out and discriminated by the device. In the detected deteriorated zones, fungal pathogens and decomposers were isolated and identified, causing either white (Phellinus hartigii, Ganoderma adspersum, Heterobasidion abietinum and Armillaria ostoyae or brown rot (Fomitopsis pinicola.

  8. Determining stocks and flows of structural wood products in single family homes in the United States between 1950 and 2010

    DEFF Research Database (Denmark)

    Sianchuk, Robert A.; McFarlane, Paul N.; Ackom, Emmanuel

    2012-01-01

    The stocks and flows of six major structural wood products (SWPs)-lumber, plywood, oriented strand board [OSB], glue laminated timber, I-joists, and laminated veneer lumber (LVL)-in US single family homes were modeled from 1950 to 2010. The consumption of these products in US single family homes......, modern SWPs, such as I-joists, LVL, and OSB, have replaced lumber and plywood products. The needs of the US single family housing industry have been met by a smaller mass of SWPs per unit area constructed. The mass of SWP present in construction wastes was influenced strongly by building cycles....... Production of construction waste peaked in 2005, when 3.31 million tonnes of SWPs were produced by 1.72 million single family housing starts. It diminished to 0.874 million tonnes of SWPs as the housing starts fell to 445,000 in 2009. In contrast, the mass of demolition wastes produced was affected...

  9. A single cell model for pretreatment of wood by microwave explosion

    Science.gov (United States)

    Xianjun Li; Yongdong Zhou; Yonglin Yan; Zhiyong Cai; Fu Feng

    2010-01-01

    A theoretical model was developed to better understand the process of microwave explosion treatment of wood cells. The cell expansion and critical conditions concerning pressure and temperature of ray parenchyma cells in Eucalyptus urophylla were simulated during microwave pretreatment. The results indicate that longitudinal and circumferential stresses were generated...

  10. Impact of grazing abandonment on floristic diversity in the priority habitat type *9562 Grecian Juniper Woods

    Science.gov (United States)

    Vrahnakis, Michael; Kazoglou, Yannis; Fotiadis, George; Kakouros, Petros; Nasiakou, Stamatia; Soutsas, Konstantinos

    2017-04-01

    The habitat type *9562 Grecian juniper woods (Juniperetum excelsae) includes Greek juniper (Juniperus excelsa M. Bieb.) forests and they are found mainly in the western sector of the Prespa National Park, NW Greece. Greek juniper forests are considered extremely rare for EU-28, recommending a priority habitat type in accordance with Directive 92/43/EEC. In addition, their ecological importance is great given its high plant taxa richness; they harbor most of the 900 plant taxa found in the western sector of the Park, many of them being important for EU or global scale. The accelerated invasion of deciduous hardwoods is the most significant risk for the habitat, since its rich flora is well-adapted to open light conditions produced by the open spaced Greek junipers. Also, the dense vegetated conditions deprive the regeneration of the photophilous Greek juniper. The invasion results from the lack of its natural controller, i.e. the grazing livestock. It is estimated that the total area of juniper forests for the Devas area decreased to 89% of the area of 1945 in favor of invasive hardwoods. The paper presents the analysis of the floristic diversity of the priority habitat type *9562 Grecian Juniper Woods (Juniperetum excelsae) (GJWs). Four (4) types of juniper forest ranges (GJWs) were distinguished in terms of canopy cover: (a) pure GJWs, (b) mixed open GJWs, (c) open GJWs, and (d) mixed dense GJWs. A total of 171 plant taxa were recorded, and distributed within 43 botanical families; the largest one being Leguminosae (26 taxa). The statistically estimated plant taxa richness for pure GJWs was 116.4, for mixed open 152.6, for open 57.9, and for mixed dense 90.2 taxa. The analysis of α-diversity indices did not reveal any specific trend of diversity for the four GJWs. The behavior of the variability of diversity among the four range types of GJWs was depending on the emphasis the used indices place on properties such as taxa richness or abundance. This fact was

  11. Dissolution of granulated wood ash examined by in situ incubation: Effects of tree species and soil type

    DEFF Research Database (Denmark)

    Callesen, Ingeborg; Ingerslev, M.; Raulund-Rasmussen, K.

    2007-01-01

    ) and a nutrient-rich soil (oxyaquic Hapludalf) in Denmark. After 7 years of incubation, the weight loss of the wood ash granulates was 20% in both soil types. Nutrient losses determined by total element analysis were about 35% for calcium, magnesium and potassium and 19% for phosphorus, regardless of tree species...

  12. Growth and wood properties of genetically improved loblolly pine: propagation type comparison and genetic parameters

    Science.gov (United States)

    Finto Antony; Laurence Schimleck; Lewis Jordan; Benjamin Hornsby; Joseph Dahlen; Richard Daniels; Alexander Clark; Luis Apiolaza; Dudley Huber

    2013-01-01

    The use of clonal varieties in forestry offers great potential to improve growth traits (quantity) and wood properties (quality) of loblolly pine (Pinus taeda L.). Loblolly pine trees established via somatic embryogenesis (clones), full-sib zygotic crosses, and half-sib zygotic open-pollinated families were sampled to identify variation in growth and wood properties...

  13. Adhesive properties of water washed cottonseed meal on four types of wood

    Science.gov (United States)

    The interest in natural product-based wood adhesives has been steadily increasing due to the environmental and sustainable concerns of petroleum-based adhesives. In this work, we reported our research on the utilization of water washed cottonseed meal (WCM) as wood adhesives. The adhesive strength a...

  14. Tissue and cell-type co-expression networks of transcription factors and wood component genes in Populus trichocarpa.

    Science.gov (United States)

    Shi, Rui; Wang, Jack P; Lin, Ying-Chung; Li, Quanzi; Sun, Ying-Hsuan; Chen, Hao; Sederoff, Ronald R; Chiang, Vincent L

    2017-05-01

    Co-expression networks based on transcriptomes of Populus trichocarpa major tissues and specific cell types suggest redundant control of cell wall component biosynthetic genes by transcription factors in wood formation. We analyzed the transcriptomes of five tissues (xylem, phloem, shoot, leaf, and root) and two wood forming cell types (fiber and vessel) of Populus trichocarpa to assemble gene co-expression subnetworks associated with wood formation. We identified 165 transcription factors (TFs) that showed xylem-, fiber-, and vessel-specific expression. Of these 165 TFs, 101 co-expressed (correlation coefficient, r > 0.7) with the 45 secondary cell wall cellulose, hemicellulose, and lignin biosynthetic genes. Each cell wall component gene co-expressed on average with 34 TFs, suggesting redundant control of the cell wall component gene expression. Co-expression analysis showed that the 101 TFs and the 45 cell wall component genes each has two distinct groups (groups 1 and 2), based on their co-expression patterns. The group 1 TFs (44 members) are predominantly xylem and fiber specific, and are all highly positively co-expressed with the group 1 cell wall component genes (30 members), suggesting their roles as major wood formation regulators. Group 1 TFs include a lateral organ boundary domain gene (LBD) that has the highest number of positively correlated cell wall component genes (36) and TFs (47). The group 2 TFs have 57 members, including 14 vessel-specific TFs, and are generally less correlated with the cell wall component genes. An exception is a vessel-specific basic helix-loop-helix (bHLH) gene that negatively correlates with 20 cell wall component genes, and may function as a key transcriptional suppressor. The co-expression networks revealed here suggest a well-structured transcriptional homeostasis for cell wall component biosynthesis during wood formation.

  15. Pretreatments for converting wood into paper and chemicals

    Science.gov (United States)

    William R. Kenealy; Carl J. Houtman; Jose Laplaza; Thomas W. Jeffries; Eric G. Horn

    2007-01-01

    Biorefining wood into paper and chemicals is not as easy as making a single traditional paper product. Paper is made from the cellulose- containing fractions of wood and processing may remove lignin and hemicellulose components. The yield and composition of the product depend upon the type of paper being produced. The paper process often alters the noncellulose...

  16. Investigating the Geomorphic and Ecologic Functions of Wood in Relationship to Habitat Type and Salmonid Redds on a Regulated California River

    Science.gov (United States)

    Senter, A. E.; Pasternack, G. B.

    2006-12-01

    Most river rehabilitation projects incorporate little to no wood in current designs, and those that do have little science to guide them. The overall goal of this research is to investigate the role of wood in a regulated, mid- sized (where river width is greater than most tree heights), Mediterranean-climate (where smaller, softer-wood trees dominate the landscape) river in order to provide a scientific foundation for the potential use of wood in rehabilitation projects within such systems. Wood structures in the active salmonid spawning reach of the Lower Mokelumne River in Central California were measured, mapped, and described during summer and fall 2006. Digital photos and GPS coordinates were used to establish wood location within the stream channel. Structural morphology was determined by measuring physical properties such as individual diameter and length, orientation to stream flow, and jam dimensions. In addition, qualitative attributes were recorded such as decay class and leaf, limb, bark, and root characteristics. A GIS wood layer will be created and added to a database of existing Mokelumne River GIS layers containing salmonid redd (salmon egg nests) densities, hydraulic conditions associated with individual redds, and sub-reach habitat types. An analysis of wood properties, redd locations and conditions, and habitat types will be used to develop a conceptual model of wood dynamics in relation to salmonid habitat on the Lower Mokelumne River. The primary products of this study will be (1) a scientific conceptual model of the role of wood in regulated gravel reaches of mid-size rivers in Mediterranean California and (2) a decision-making framework that will enable river managers to include scientifically based wood structures into rehabilitation designs, thereby enhancing spawning habitat, stream complexity, and biological diversity. These tools will be developed in collaboration with East Bay Municipal Utilities District to aid in the continuing

  17. Analysis of existing structure and emissions of wood combustion plants for the production of heat and electricity in Bavaria

    International Nuclear Information System (INIS)

    Joa, Bettina

    2014-01-01

    This work deals with the detailed analysis of the existing structure of all Bavarian wood burning plants for the generation of heat and electricity as well as the determination of the resulting emission emissions in 2013. The number of wood burning plants in the single-chamber fireplaces, wood central heating and wood-fired heating plants which are in operation in the year 2013 were determined, and how many plants are existing in the various areas like pellet stoves, traditional ovens, wood-burning fireplace, pellet central heating systems, wood chips central heating systems, fire-wood central heating systems, wood combined heat and power plant (electricity and heat) and wood power plants (heat). In addition, the regional distribution of the wood burning plants in the Bavarian governmental districts is investigated as well as the type and amount of energy produced by them (heat, electricity). [de

  18. Development Directions for Various Types of the Light Wood-Framed Structures

    Science.gov (United States)

    Malesza, J.; Baszeń, M.; Miedziałowski, Cz

    2017-11-01

    The paper presents current trends in the development of the wood-framed structures. Authors describe the evolution of the technology of implementation, the production process of precast elements of buildings as well as selected realization on the site of these kinds of structures. The attention has been paid to the effect of implementation phases on construction and erecting technology of the wood-framed structures. The paper draws attention to the importance and enhancement of structural analysis of structures in individual phases of building realization.

  19. Pyrolysis kinetic evaluation by single-step for waste wood from reforestation.

    Science.gov (United States)

    da Silva, Jean Constantino Gomes; Alves, José Luiz Francisco; Galdino, Wendell Venicio de Araujo; Andersen, Silvia Layara Floriani; de Sena, Rennio Felix

    2018-02-01

    The objective of this study was to evaluate the kinetic parameters of pyrolysis of waste wood from reforestation: Eucalyptus benthamii (EB), Eucalyptus dunnii (ED) and Pinus elliottii (PN). The kinetic study was performed using the Friedman, Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS), Starink, and Vyazovkin methods from the experimental data at four heating rates (5, 10, 20 and 30 °C min -1 ). The Friedman method presented higher activation energy values (E a ) when compared to the other methods (E a EB  = 142.98 kJ mol -1 , E a ED  = 147.71 kJ mol -1 , E a PN  = 155.46 kJ mol -1 ). The KAS, Starink and Vyazovkin methods resulted in approximate values of activation energy (E a EB  = 132.83-133.31 kJ mol -1 , E a ED  = 137.51-137.98 kJ mol -1 , E a PN  = 145.24-145.70 kJ mol -1 ) due to the approximation equations with lowest relative errors. The simulation of curves using the kinetic parameters obtained with the Vyazovkin method showed that the decomposition process of EB and ED occurs as a multi-step process resulting in an unsatisfactory result for the simulation. On the other hand, for PN a satisfactory fit to the experimental data was obtained, which demonstrates its suitability for application to the modeling of thermochemical systems. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Molecular genetic typing of three forms of wood and field mice belonging to a transpalearctic genus (Apodemus, Muridae, Rodentia)

    Energy Technology Data Exchange (ETDEWEB)

    Chelomina, G.N. [Institute of Biology and Soil Sciences, Vladivostok (Russian Federation); Lyapunova, E.A.; Vorontsov, N.N. [Kol`tsov Institute of Developmental Biology, Moscow (Russian Federation)] [and others

    1995-06-01

    The genomes of three species of wood mouse (Apodemus fulvipectus and A. ponticus from the Caucasus and A. argenteus from Japan) were compared by means of restriction analysis of nuclear DNA. The species are differentiated from each other and from previously studied species. Each species has its species-specific features. Within the genus Apodemus, A. ponticus is most closely related to the European species A. sylvaticus and A. flavicollis. A. fulvipectus has a peculiar type of restriction with EcoR I (specific for dispersed repeats) and Hind III (specific for satDNA). The genome of this species contains three families of EcoR I repeats previously found in various species (European and Asian) of wood mouse and Hind III components characteristic of both wood and field mice. A. argenteus differs from all other forms of Apodemus, the genome of which contains the 375-bp Hind III satellite, by the presence of an EcoR I satDNA fraction consisting of 240-bp repeating units. 22 refs., 2 figs.

  1. Single-nucleotide polymorphisms in PtoCesA7 and their association with growth and wood properties in Populus tomentosa.

    Science.gov (United States)

    Tian, Jiaxing; Chang, Mengqi; Du, Qingzhang; Xu, Baohua; Zhang, Deqiang

    2014-06-01

    Cellulose synthase (CesA) genes encode the enzymes that synthesize cellulose; therefore, CesAs play central roles in plant development and affect the yield and quality of wood, essential properties for industrial applications of plant biomass. To effectively manipulate wood biosynthesis in trees and improve wood quality, we thus require a better understanding of the natural variation in CesAs. Association studies have emerged as a powerful tool for identification of variation associated with quantitative traits. Here, we used a candidate gene-based association mapping approach to identify PtoCesA7 allelic variants that associate with growth and wood quality traits in Populus tomentosa. We isolated a full-length PtoCesA7 cDNA and observed high PtoCesA7 expression in xylem, consistent with the xylem-specific expression of CesA7. Nucleotide diversity and linkage disequilibrium (LD) in PtoCesA7, sampled from the P. tomentosa natural distribution, revealed that PtoCesA7 harbors high nucleotide diversity (π(T) = 0.0091) and low LD (r(2) ≥ 0.1, within 800 bp). By association analysis, we identified seven single-nucleotide polymorphisms (SNPs) (false discovery rate Q wood properties, explaining 3.62-10.59 % of the phenotypic variance. We also validated 9 of the 10 significant marker-trait associations in at least one of three smaller subsets (climatic regions) or in a linkage-mapping population. Thus, our study identified functional PtoCesA7 allelic variants associated with growth and wood quality traits, giving new insights into genes affecting wood quality and quantity. From an applied perspective, the SNPs revealed in this study have potential applications in marker-assisted breeding.

  2. Mechanical Behavior of Dowel-Type Joints Made of Wood Scrimber Composite.

    Science.gov (United States)

    He, Minjuan; Tao, Duo; Li, Zheng; Li, Maolin

    2016-07-15

    As a renewable building material with low embodied energy characteristics, wood has gained more and more attention in the green and sustainable building industry. In terms of material resource and physical properties, scrimber composite not only makes full use of fast-growing wood species, but also has better mechanical performance and less inherent variability than natural wood material. In this study, the mechanical behavior of bolted beam-to-column joints built with a kind of scrimber composite was investigated both experimentally and numerically. Two groups of specimens were tested under monotonic and low frequency cyclic loading protocols. The experimental results showed that the bolted joints built with scrimber composite performed well in initial stiffness, ductility, and energy dissipation. A three-dimensional (3D) non-linear finite element model (FEM) for the bolted beam-to-column joints was then developed and validated by experimental results. The validated model was further used to investigate the failure mechanism of the bolted joints through stress analysis. This study can contribute to the application of the proposed scrimber composite in structural engineering, and the developed FEM can serve as a useful tool to evaluate the mechanical behavior of such bolted beam-to-column joints with different configurations in future research.

  3. Influence of fiber type, fiber mat orientation, and process time on the properties of a wood fiber/polymer composite

    DEFF Research Database (Denmark)

    Plackett, David; Torgilsson, R.; Løgstrup Andersen, T.

    2002-01-01

    A rapid press consolidation technique was used to produce composites from two types of air-laid wood fiber mat, incorporating either mechanically refined or bleached chemi-thermomechanically refined Norway Spruce [Picea abies (L.) Karst] and a bicomponent polymer fiber. The manufacturing technique...... involved pre-compression, contact heating to the process temperature under vacuum and then rapid transfer to the press for consolidation and cooling. Composites were tested to determine response to water or water vapor, porosity, fiber volume fraction and tensile properties. The composites absorbed water...

  4. Wood creosote, the principal active ingredient of seirogan, an herbal antidiarrheal medicine: a single-dose, dose-escalation safety and pharmacokinetic study.

    Science.gov (United States)

    Kuge, Tomoo; Shibata, Takashi; Willett, Michael S

    2003-11-01

    To assess the safety, tolerability and pharmacokinetics of escalating single doses of wood creosote, an herbal antidiarrheal and antispasmodic agent. Randomized, double-blind, placebo-controlled study. Clinical research center. Forty (32 men, 8 women) healthy volunteers aged 19-42 years. By random assignment, 22 men and 8 women received escalating single doses of wood creosote (45, 90, 135, 180, and 225 mg) and 10 men received placebo (for each of the five dose levels, 6 subjects received active substance and 2 subjects received placebo). Vital signs, laboratory tests, and electrocardiograms were assessed; no dose-related or clinically significant changes were noted. Serial blood samples were obtained to determine the pharmacokinetics of four major active components of wood creosote: total (conjugated plus free) guaiacol, creosol, o-cresol, and 4-ethylguaiacol. The most common adverse events were mild headache and dizziness, with no dose-related trends being apparent. Area under the concentration-time curve from time zero to infinity increased in a dose-proportional manner for total guaiacol, creosol, and o-cresol and was not assessed for total 4-ethylguaiacol owing to lack of data at the low dose level. No apparent differences by sex were noted for any of the four active components. All four components were rapidly eliminated. Single oral doses of wood creosote up to 225 mg were safe and well tolerated in healthy men and women. Also, the doses of wood creosote were rapidly absorbed, conjugated, and eliminated. Such a rapid onset and short duration of action would appear desirable in the treatment of acute nonspecific diarrhea.

  5. Single bovine sperm sex typing by amelogenin nested PCR.

    Science.gov (United States)

    Colley, A; Buhr, M; Golovan, S P

    2008-10-01

    Sex-sorted bovine semen has become a valuable tool in animal production for sex preselection. Development of novel sperm sexing technologies, or evaluation of the quality of existing methods, often requires a single-sperm, sex-typing method that is reliable and easy to perform. In the present study, we report the development, validation, and application of a simple, reliable, and cost-effective method for single-sperm sex typing using nested polymerase chain reaction (PCR), based on the amelogenin gene. Several hundred single sperm were isolated using a simple manual technique, or a high-speed flow-sorter, and were successfully sex-typed using the amelogenin nested PCR. Based on the pooled results of individual sperm, there was no significant difference in the semen sex ratio of unsorted (44.6% X-sperm and 55.4% Y-sperm) or X/Y-sorted semen (91.4% X-sperm and 94.0% Y-sperm), as compared to the expected ratio in unsorted semen or the post-sorting reanalysis data, respectively. The amelogenin single-sperm sexing method was an adaptable, accurate, and reliable tool for single-sperm sex typing.

  6. Wood-associated fauna collected during the KuramBio expedition in the North West Pacific

    Science.gov (United States)

    Schwabe, Enrico; Bartsch, Ilse; Błażewicz-Paszkowycz, Magdalena; Brenke, Nils; Chernyshev, Alexei V.; Elsner, Nikolaus O.; Fischer, Viola; Jażdżewska, Anna; Malyutina, Marina V.; Miljutin, Dmitry; Miljutina, Maria; Kamenev, Gennady M.; Karanovic, Ivana; Maiorova, Anastassya; Würzberg, Laura

    2015-01-01

    Individual wood fragments obtained from Agassiz trawl samples in the abyssal plain area off the Kuril-Kamchatka Trench were analysed for faunistic components. Out of seven pieces of wood collected, only five harboured fauna and each showed distinctively different colonization patterns. In total, 257 specimens, mainly belonging to the phyla Arthropoda, Nematoda, Mollusca and Annelida, were collected from the available pieces of wood. While wood-boring bivalves of the genus Xylophaga, generally seen as opportunists among wood-converting organisms, were present at nearly all stations, the overwhelming majority of taxa found were restricted to individual pieces of wood. A fresh piece of wood from a site opposite to the Tsugaru Strait, was the most heavily colonized. The presence of shallow or even putative fresh-water taxa beside truly deep-water components possibly suggests a recent sinking of that particular wood fragment and demonstrates the role of such ephemeral organic objects in deep-sea ecosystems as energy-rich feeding grounds and potential distributional stepping stones. Detailed studies of driftwood communities on single sunken wood fragments from deep oceans are limited. The present data not only demonstrate a tolerance of some taxa to changes in physical parameters, such as hydrostatic pressure, salinity and temperature, but also indicate a higher biodiversity on fresher wood pieces compared to wood which already underwent decomposition processes. It is, however, not clear whether the species diversity was linked to the type of wood, since exhaustive analyses on the wood pieces themselves were not conducted.

  7. Multifactorial antimicrobial wood protectants

    Science.gov (United States)

    Robert D. Coleman; Carol A. Clausen

    2008-01-01

    It is unlikely that a single antimicrobial compound, whether synthetic or natural, will provide the ‘magic bullet’ for eliminating multiple biological agents affecting wood products. Development of synergistic combinations of selected compounds, especially those derived from natural sources, is recognized as a promising approach to improved wood protection. Recent...

  8. Investigation of bio-composites using Novolac type liquefied wood resin: effects of liquefaction and fabrication conditions

    Science.gov (United States)

    Hui Pan; Chung-Yun Hse; Todd F. Shupe

    2009-01-01

    Wood liquefaction using an organic solvent and an acid catalyst has long been studied as a novel technique to utilize biomass as an alternative to petroleum-based products. Oxalic acid is a weaker organic acid than a mineral acid and wood liquefaction with oxalic acid as a catalyst will result in a higher amount of wood residue than that with a mineral acid....

  9. Effects of Modifier Type on Properties of in Situ Organo-Montmorillonite Modified Wood Flour/Poly(lactic acid) Composites.

    Science.gov (United States)

    Liu, Ru; Chen, Yu; Cao, Jinzhen

    2016-01-13

    Wood flour (WF) was modified with sodium-montmorillonite (Na-MMT) and two types of surfactant modifiers, namely, didecyl dimethylammonium chloride (DDAC) and sodium dodecyl sulfonate (SDS) though a two-step process inside WF. The thus-modified WFs were characterized, and the effects of MMT type on physical, mechanical, and thermal properties of their composites with poly(lactic acid) (PLA) were investigated. The results showed: (1) either DDAC or SDS could modified Na-MMT into OMMT, and then uniformly distributed in WF cell walls; (2) OMMT improved the physical properties, most mechanical properties, and thermal properties of the composites except for the impact strength; and (3) compared with SDS, DDAC seemed to perform better in properties of composites. However, DDAC showed some negative effect on the early stage of composite thermal decomposition.

  10. Wood flour

    Science.gov (United States)

    Craig M. Clemons; Daniel F. Caufield

    2005-01-01

    The term “wood flour” is somewhat ambiguous. Reineke states that the term wood flour “is applied somewhat loosely to wood reduced to finely divided particles approximating those of cereal flours in size, appearance, and texture”. Though its definition is imprecise, the term wood flour is in common use. Practically speaking, wood flour usually refers to wood particles...

  11. Single-cell LEP-type cavity on measurement stand

    CERN Multimedia

    CERN PhotoLab

    1982-01-01

    A single-cell cavity, made of copper, with tapered connectors for impedance measurements. It was used as a model of LEP-type superconducting cavities, to investigate impedance and higher-order modes and operated at around 600 MHz (the LEP acceleration frequency was 352.2 MHz). See 8202500.

  12. Origin of new Brassica types from a single intergeneric hybrid ...

    Indian Academy of Sciences (India)

    Origin of new Brassica types from a single intergeneric hybrid between B. rapa and Orychophragmus violaceus by rapid chromosome evolution and introgression ... The lines with high productivity showed not only a wide spectrum of phenotypes but also obvious variations in fatty acid profiles of seed oil and glucosinolate ...

  13. The Wood Strengthening and Decorative Automated Production Line ZY-06L-Type Manipulator Motion Analysis and Simulation

    Directory of Open Access Journals (Sweden)

    Wu Hao

    2014-03-01

    Full Text Available ZY-06L-type manipulator is the important components of Wood Surface layer Strengthening and Decorative Automated Production Line, designed for a variety of sheet metal or semi-finished components handling, distribution and laying work in the workshop. Through the establishment of the manipulator kinematics equations, combined the position coordinates of the manipulator and object in the actual work environment, and solving this equation to get the relationship between the manipulator end-effectors position and posture with the joint variables. The use of engineering software UG NX8.0 for modeling and simulation of the manipulator, and analysis the reasonableness of structural and workflow design. Provide the basis and reference to the manipulator structure optimization and control systems developments.

  14. Quinoline alkaloids and friedelane-type triterpenes isolated from leaves and wood of Esenbeckia alata Kunt (Rutaceae)

    International Nuclear Information System (INIS)

    Cuca-Suarez, Luis Enrique; Barrera, Ericsson David Coy; Alvarez Caballero, Juan Manuel

    2011-01-01

    This work describes the phytochemical exploration of the ethanol extract from leaves and wood of Esenbeckia alata, leading to the isolation and identification of quinoline alkaloids 4-methoxy-3-(3'-methyl-but-2'-enyl)-N-methyl-quinolin-2(1 H)-one, N-methylflindersine, dictamine, kokusaginine, G-fagarine, flindersiamine, as well as the fridelane-type triterpenes, frideline, fridelanol and its acetate derivative. Identification of these compounds was based on full analyses of spectroscopic data ( 1 H, 13 C, 1 D, 2 D, IR, MS) and comparison with data reported in literature. Compound 4-methoxy-3-(3'-methyl-but-2'-enyl)-N-methyl-quinolin-2(1 H)-one is reported for the first time for the genus Esenbeckia. (author)

  15. Quinoline alkaloids and friedelane-type triterpenes isolated from leaves and wood of Esenbeckia alata Kunt (Rutaceae)

    Energy Technology Data Exchange (ETDEWEB)

    Cuca-Suarez, Luis Enrique; Barrera, Ericsson David Coy [Universidad Nacional de Colombia, Bogota (Colombia). Dept. de Quimica; Alvarez Caballero, Juan Manuel [Universidad del Magdalena, Santa Marta DTCH (Colombia). Facultad de Ciencias Basicas

    2011-07-01

    This work describes the phytochemical exploration of the ethanol extract from leaves and wood of Esenbeckia alata, leading to the isolation and identification of quinoline alkaloids 4-methoxy-3-(3'-methyl-but-2'-enyl)-N-methyl-quinolin-2(1 H)-one, N-methylflindersine, dictamine, kokusaginine, G-fagarine, flindersiamine, as well as the fridelane-type triterpenes, frideline, fridelanol and its acetate derivative. Identification of these compounds was based on full analyses of spectroscopic data ({sup 1}H, {sup 13}C, {sup 1}D, {sup 2}D, IR, MS) and comparison with data reported in literature. Compound 4-methoxy-3-(3'-methyl-but-2'-enyl)-N-methyl-quinolin-2(1 H)-one is reported for the first time for the genus Esenbeckia. (author)

  16. Quinoline alkaloids and friedelane-type triterpenes isolated from leaves and wood of Esenbeckia alata kunt (Rutaceae

    Directory of Open Access Journals (Sweden)

    Luis Enrique Cuca-Suarez

    2011-01-01

    Full Text Available This work describes the phytochemical exploration of the ethanol extract from leaves and wood of Esenbeckia alata, leading to the isolation and identification of quinoline alkaloids 4-methoxy-3-(3'-methyl-but-2'-enyl-N-methyl-quinolin-2(1 H-one, N-methylflindersine, dictamine, kokusaginine, Γ-fagarine, flindersiamine, as well as the fridelane-type triterpenes, frideline, fridelanol and its acetate derivative. Identification of these compounds was based on full analyses of spectroscopic data (¹H, 13C, 1D, 2D, IR, MS and comparison with data reported in literature. Compound 4-methoxy-3-(3'-methyl-but-2'-enyl-N-methyl-quinolin-2(1 H-one is reported for the first time for the genus Esenbeckia.

  17. Single cell transcriptional analysis reveals novel innate immune cell types

    Directory of Open Access Journals (Sweden)

    Linda E. Kippner

    2014-06-01

    Full Text Available Single-cell analysis has the potential to provide us with a host of new knowledge about biological systems, but it comes with the challenge of correctly interpreting the biological information. While emerging techniques have made it possible to measure inter-cellular variability at the transcriptome level, no consensus yet exists on the most appropriate method of data analysis of such single cell data. Methods for analysis of transcriptional data at the population level are well established but are not well suited to single cell analysis due to their dependence on population averages. In order to address this question, we have systematically tested combinations of methods for primary data analysis on single cell transcription data generated from two types of primary immune cells, neutrophils and T lymphocytes. Cells were obtained from healthy individuals, and single cell transcript expression data was obtained by a combination of single cell sorting and nanoscale quantitative real time PCR (qRT-PCR for markers of cell type, intracellular signaling, and immune functionality. Gene expression analysis was focused on hierarchical clustering to determine the existence of cellular subgroups within the populations. Nine combinations of criteria for data exclusion and normalization were tested and evaluated. Bimodality in gene expression indicated the presence of cellular subgroups which were also revealed by data clustering. We observed evidence for two clearly defined cellular subtypes in the neutrophil populations and at least two in the T lymphocyte populations. When normalizing the data by different methods, we observed varying outcomes with corresponding interpretations of the biological characteristics of the cell populations. Normalization of the data by linear standardization taking into account technical effects such as plate effects, resulted in interpretations that most closely matched biological expectations. Single cell transcription

  18. Aluminum-rich mesoporous MFI - type zeolite single crystals

    DEFF Research Database (Denmark)

    Kustova, Marina; Kustov, Arkadii; Christensen, Christina Hviid

    2005-01-01

    are characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), ammonia temperature programmed desorption (NH3-TPD), and N-2 adsorption measurements. The obtained zeolites combine the high crystallinity and the characteristic micropores of zeolites with an intracrystalline mesopore system....... With this technique, only zeolites with relatively low Al contents were reported (Si/Al ratio about 100). In this work, the preparation of aluminum-rich mesoporous MFI-type zeolite single crystals (Si/Al similar to 16-50) using aluminum isopropoxide as the aluminum Source is reported for the first time. All samples...

  19. Energy from wood - an overview

    International Nuclear Information System (INIS)

    Nussbaumer, T.

    2000-01-01

    The present publication is the introduction to a series of papers on fundamentals and applications of wood energy. It summarizes figures and data of the actual situation of fuel wood utilization in Switzerland and its potential for the future. Further, the advantages of bio-energy are discussed and the possibilities of funding for bio-energy in Switzerland are described. Wood contributes with 2.5% to the total energy demand in Switzerland nowadays. However, the utilization of wood energy can be more than doubled, which is one of the targets of the Swiss energy policy. The supply chains for the different types of fuel wood are described and specifications and prices of log wood, forestry wood chips and wood residues are presented. The main applications of wood energy are residential heating with manually operated wood boilers and stoves, on the one hand, and heat production with automatic wood furnaces in industry and communities, on the other hand. Automatic furnaces have been promoted in the past ten years and hence they contribute nowadays with more than 50% to the energy supply from wood with a further growing share. As an assistance for further information, a list of institutions and addresses in the field of wood energy in Switzerland is given in the paper. (author)

  20. Single electron transistor with P-type sidewall spacer gates.

    Science.gov (United States)

    Lee, Jung Han; Li, Dong Hua; Lee, Joung-Eob; Kang, Kwon-Chil; Kim, Kyungwan; Park, Byung-Gook

    2011-07-01

    A single-electron transistor (SET) is one of the promising solutions to overcome the scaling limit of the Metal-Oxide-Semiconductor Field Effect Transistor (MOSFET). Up to now, various kinds of SETs are being proposed and SETs with a dual gate (DG) structure using an electrical potential barrier have been demonstrated for room temperature operation. To operate DG-SETs, however, extra bias of side gates is necessary. It causes new problems that the electrode for side gates and the extra bias for electrical barrier increase the complexity in circuit design and operation power consumption, respectively. For the reason, a new mechanism using work function (WF) difference is applied to operate a SET at room temperature by three electrodes. Its structure consists of an undoped active region, a control gate, n-doped source/drain electrodes, and metal/silicide or p-type silicon side gates, and a SET with metal/silicide gates or p-type silicon gates forms tunnel barriers induced by work function between an undoped channel and grounded side gates. Via simulation, the effectiveness of the new mechanism is confirmed through various silicide materials that have different WF values. Furthermore, by considering the realistic conditions of the fabrication process, SET with p-type sidewall spacer gates was designed, and its brief fabrication process was introduced. The characteristics of its electrical barrier and the controllability of its control gate were also confirmed via simulation. Finally, a single-hole transistor with n-type sidewall spacer gates was designed.

  1. Wood Dust

    Science.gov (United States)

    Learn about wood dust, which can raise the risk of cancers of the paranasal sinuses and nasal cavity. High amounts of wood dust are produced in sawmills, and in the furniture-making, cabinet-making, and carpentry industries.

  2. Treatments that enhance physical properties of wood

    Science.gov (United States)

    Roger M. Rowell; Peggy Konkol

    1987-01-01

    This paper was prepared for anyone who wants to know more about enhancing wood’s physical properties, from the amateur wood carver to the president of a forest products company. The authors describe chemical and physical treatments of wood that enhance the strength, stiffness, water repellency, and stability of wood. Five types of treatments are described: 1. water-...

  3. Physical properties and moisture relations of wood

    Science.gov (United States)

    William Simpson; Anton TenWolde

    1999-01-01

    The versatility of wood is demonstrated by a wide variety of products. This variety is a result of a spectrum of desirable physical characteristics or properties among the many species of wood. In many cases, more than one property of wood is important to the end product. For example, to select a wood species for a product, the value of appearance- type properties,...

  4. Wood preservation

    Science.gov (United States)

    Rebecca E. Ibach

    2003-01-01

    When wood is exposed to various environmental conditions, many degradation reactions (biological, ultraviolet, mechanical, moisture, and chemical) can occur. To protect wood from biological degradation, chemical preservatives are applied by nonpressure or pressure treatment. Penetration and retention of a chemical depend upon the wood species and the amount of...

  5. Comparison of usefulness of three types of artificial substrata (glass, wood and plastic) when studying settlement patterns of periphyton in lakes of different trophic status.

    Science.gov (United States)

    Danilov, R A; Ekelund, N G

    2001-07-01

    Usefulness of three types of artificial substrata (glass, wood and plastic) was tested when studying settlement patterns of periphyton in lakes of different trophic status. Strictly eu-, meso- and oligotrophic lakes in central Sweden were chosen as objects of the study. Glass slides, glass tubes, pieces of plastic (PVC) and pieces of wood of similar dimensions were placed for 9 weeks in July-August vertically 3 cm above bottom at a total depth of ca. 30 cm. Substrata were located at well-illuminated places without any other submerged objects (like macrophytes and stones), which could potentially affect colonisation patterns by algae. Periphyton communities, which colonised both the glass tubes and the pieces of wood tested, were specific enough to enable a clear classification of the lakes studied in eu-, meso- and oligotrophic. Glass tubes turned out to be the most favourable substratum when investigating settlement patterns of periphyton in this study. Although also colonised by periphytic species, wood did not support the same diversity and abundance of species as glass did. No algae were detected on the plastics studied. The plastics were covered entirely by a slime layer of bacteria. It is discussed if the nature of plastics could have some inhibitory effects on algal growth or the slime layer itself may have prevented settlement of algal spores.

  6. Wood-inhabiting fungi in southern Italy forest stands: morphogroups, vegetation types and decay classes.

    Science.gov (United States)

    Granito, Vito Mario; Lunghini, Dario; Maggi, Oriana; Persiani, Anna Maria

    2015-01-01

    The authors conducted an ecological study of forests subjected to varying management. The aim of the study was to extend and integrate, within a multivariate context, knowledge of how saproxylic fungal communities behave along altitudinal/vegetational gradients in response to the varying features and quality of coarse woody debris (CWD). The intra-annual seasonal monitoring of saproxylic fungi, based on sporocarp inventories, was used to investigate saproxylic fungi in relation to vegetation types and management categories. We analyzed fungal species occurrence, recorded according to the presence/absence and frequency of sporocarps, on the basis of the harvest season, of coarse woody debris decay classes as well as other environmental and ecological variables. Two-way cluster analysis, DCA and Spearman's rank correlations, for indirect gradient analysis, were performed to identify any patterns of seasonality and decay. Most of the species were found on CWD in an intermediate decay stage. The first DCA axis revealed the vegetational/microclimate gradient as the main driver of fungal community composition, while the second axis corresponded to a strong gradient of CWD decay classes. © 2015 by The Mycological Society of America.

  7. Corrosion of Fasteners in Wood Treated with Newer Wood Preservatives

    Science.gov (United States)

    Samuel L. Zelinka

    2013-01-01

    This document compiles recent research findings related to corrosion of metals in preservative treated wood into a single report on corrosion of metals in wood. The research was conducted as part of the Research, Technology and Education portion of the National Historic Covered Bridge Preservation (NHCBP) Program administered by the Federal Highway Administration. The...

  8. Wood composites

    Science.gov (United States)

    Lars Berglund; Roger M. Rowell

    2005-01-01

    A composite can be defined as two or more elements held together by a matrix. By this definition, what we call “solid wood” is a composite. Solid wood is a three-dimensional composite composed of cellulose, hemicelluloses and lignin (with smaller amounts of inorganics and extractives), held together by a lignin matrix. The advantages of developing wood composites are (...

  9. Manufacturing methods and magnetic characteristics of magnetic wood

    International Nuclear Information System (INIS)

    Oka, H.; Hojo, A.; Osada, H.; Namizaki, Y.; Taniuchi, H.

    2004-01-01

    The relationship between wood construction and DC magnetic characteristics for three types of magnetic wood was experimentally investigated. The results show that the magnetic characteristics of each type of magnetic wood are dependent on the magnetic materials, the density of the magnetic material and the construction of the wood. Furthermore, it was determined that the relationship between the fiber direction and the magnetic path direction of the magnetic wood influenced the wood's magnetic characteristics

  10. The importance of forest type, tree species and wood posture to saproxylic wasp (Hymenoptera) communities in the southeastern United States.

    Science.gov (United States)

    Michael Ulyshen; Thomas Pucci; James Hanula

    2011-01-01

    Although the forests of the southeastern United States are among the most productive and diverse in North America, information needed to develop conservation guidelines for the saproxylic (i.e., dependent on dead wood) fauna endemic to the region is lacking. Particularly little is known about the habitat associations and requirements of saproxylic parasitoids even...

  11. Wood pellet research program

    International Nuclear Information System (INIS)

    Sohkansanj, S.; Bi, T.

    2006-01-01

    Wood pellets are composed of waste wood materials such as sawmill residue, municipal landfill waste and grain crops. Due to the high temperature combustion used to form the waste materials into the pellet, no additives or glues are necessary to bind them. The pellets are typically used for home heating; heat and power production; poultry bedding; and in biorefineries. This presentation provided an outline of the University of British Columbia wood pellet research and development program. Research at the university is being conducted to develop new types of pellets. Researchers at the program also analyze the physical and chemical properties of pellets in order to optimize pellet density and heating values. Wood pellet modelling and simulation studies are carried out, and various training and education programs are also offered. Research is currently being conducted to develop a reactor for off-gassing experiments. This presentation also provided details of a study investigating the economics of wood pellet production and transport. Pellet production costs and feedstock costs were compared. A summary of the costs and energy inputs of pellet production included details of product storage; transportation and transfer; handling; and transportation to energy plants. It was concluded that more than 35 per cent of the energy content of biomass is used up in the processing and transport of Canadian wood pellets to Europe. refs., tabs., figs

  12. Sensitivity of the Single Particle Soot Photometer to different black carbon types

    Science.gov (United States)

    Laborde, M.; Mertes, P.; Zieger, P.; Dommen, J.; Baltensperger, U.; Gysel, M.

    2012-05-01

    Black carbon (BC) is now mainly of anthropogenic origin. It is the dominant light absorbing component of atmospheric aerosols, playing an important role in the earth's radiative balance and therefore relevant to climate change studies. In addition, BC is known to be harmful to human beings making it relevant to policy makers. Nevertheless, the measurement of BC remains biased by the instrument-based definition of BC. The Single Particle Soot Photometer (SP2), allows the measurement of the refractory BC (rBC) mass of individual particles using laser-induced incandescence. However, the SP2 needs an empirical calibration to retrieve the rBC mass from the incandescence signal and the sensitivity of the SP2 differs between different BC types. Ideally, for atmospheric studies, the SP2 should be calibrated using ambient particles containing a known mass of ambient rBC. However, such "ambient BC" calibration particles cannot easily be obtained and thus commercially available BC particles are commonly used for SP2 calibration instead. In this study we tested the sensitivity of the SP2 to different BC types in order to characterize the potential error introduced by using non-ambient BC for calibration. The sensitivity of the SP2 was determined, using an aerosol particle mass analyzer, for rBC from thermodenuded diesel exhaust, wood burning exhaust and ambient particles as well as for commercially available products: Aquadag® and fullerene soot. Thermodenuded, fresh diesel exhaust has been found to be ideal for SP2 calibration for two reasons. First, the small amount of non-BC matter upon emission reduces the risk of bias due to incomplete removal of non-BC matter and second, it is considered to represent atmospheric rBC in urban locations where diesel exhaust is the main source of BC. The SP2 was found to be up to 16% less sensitive to rBC from thermodenuded ambient particles (≤15 fg) than rBC from diesel exhaust, however, at least part of this difference can be explained

  13. Characterization of black carbon and organic contaminants in wood ash from different feedstocks and types of furnaces

    Science.gov (United States)

    Merino, Agustin; Rey-Salgueiro, Ledicia; Omil, Beatriz; Martinez-Carballo, Elena; Simal-Gandara, Jesus

    2015-04-01

    Due to their important concentration of nutrient and charcoal, wood ash from biomass power plants (WA) can be used as a fertilizer and organic amendment in intensively managed soils. Unlike biochar produced in under anoxic conditions, the nature of the organic compounds present in wood ash has been scarcely studied. Due to the incomplete combustion, wood ash may contain a wide range of organic compounds, from charred to highly condensed refractory biomass, which determines the possibilities of WA as an organic amendment. In addition, the possible environmental risk of this practice must be assessed by determining the content of water-soluble and insoluble organic contaminants. due to the incomplete combustion of organic matter, organic pollutants, such as Polycyclic Aromatic Hydrocarbons (PAHs), can be formed and can remain in the combustion residue. Also, the four alkyl benzene volatile organic compounds (benzene, toluene, ethylbenzene, and the ortho, para, and meta xylenes) can be formed, depending on certain conditions during combustion. For this study 15 biomass power stations in Spain were selected. In all of them the feedstock is pine or eucalyptus branches and bark. Nine of them were bottom wood ash generated from wood fires furnaces, obtained from grate-fired or water-tube boilers. Whereas four of them were fly ash, obtained in cyclone separators. The samples were collected following a common procedure to ensure the representiveness of the sampling. Bottom ash samples were fraccionated in three fractions: 5mm. Each fraction was characterized for organic matter and BTEX, styrene and total petroleum hydrocarbons Polycyclic Aromatic Hydrocarbons. For each analyzes, three replicates were analyzed per sample. Mixes wood ash shows higher amounts of charred material than fly ash. The 13 C CPMAS NMR, DSC/TG and FTIR analysis showed the loss of carbohydrates and aliphatic constituents and revealed the formation of aromatic compounds. The atomic H/C ratios, NMR

  14. Factors that lead to failure with wood adhesive bonds

    Science.gov (United States)

    Charles R. Frihart; James F. Beecher

    2016-01-01

    Understanding what makes a good wood adhesive is difficult since the type of adhesive, wood species, bonding process, and resultant products vary considerably. Wood bonds are subjected to a variety of tests that reflect the different product performance criteria in diverse countries. The most common tests involve some type of moisture resistance; both wood and adhesive...

  15. Thermal behavior of Liquidambar orientalis mill wood before and after extraction processes

    Directory of Open Access Journals (Sweden)

    Evren Terzi

    2017-11-01

    Full Text Available The effect of extractives on the thermal behavior of Liquidambar orientalis Mill. (storax wood is studied using thermogravimetric analysis (TGA. To evaluate the effects of polar and apolar extractives on the thermal behavior of wood, sawdust samples from the heartwood of L. orientalis are extracted with either cold water (48 h, hot water (48 h, or ethanol/toluene (1:2 v/v (6 h prior to thermal analysis. Thermogravimetry (TG curves show that polar and apolar extractives promote char formation, increase the amount of residue, and improve the thermal behavior of L. orientalis wood. In addition, derivative thermogravimetry (DTG curves demonstrate that thermal degradation of un-extracted and cold water-extracted wood samples occurs in a single step, while a two-step degradation pattern is seen for hot water- and ethanol/toluene-extracted wood samples. It is also observed that first degradation reactions in hot water and ethanol/toluene-extracted wood samples occur faster than those in unextracted and cold water-extracted wood samples. Although there are approximately half the number of extracted apolar compounds compared to polar compounds, the removal of both types of compounds affect the thermal properties of L. orientalis wood to the same degree. It is thus deduced that apolar extractives significantly affect the thermal behavior of L. orientalis wood.

  16. Synthesis and cure kinetics of liquefied wood/phenol/formaldehyde resins

    Science.gov (United States)

    Hui Pan; Todd F. Shupe; Chung-Yun Hse

    2008-01-01

    Wood liquefaction was conducted at a 2/1 phenol/wood ratio in two different reactors: (1) an atmospheric three-necked flask reactor and (2) a sealed Parr reactor. The liquefied wood mixture (liquefied wood, unreacted phenol, and wood residue) was further condensed with formaldehyde under acidic conditions to synthesize two novolac-type liquefied wood/phenol/...

  17. Complex Dynamic Scene Perception: Effects of Attentional Set on Perceiving Single and Multiple Event Types

    Science.gov (United States)

    Sanocki, Thomas; Sulman, Noah

    2013-01-01

    Three experiments measured the efficiency of monitoring complex scenes composed of changing objects, or events. All events lasted about 4 s, but in a given block of trials, could be of a single type (single task) or of multiple types (multitask, with a total of four event types). Overall accuracy of detecting target events amid distractors was…

  18. Wood preservation

    Science.gov (United States)

    Kevin Archer; Stan Lebow

    2006-01-01

    Wood preservation can be interpreted to mean protection from fire, chemical degradation, mechanical wear, weathering, as well as biological attack. In this chapter, the term preservation is applied more restrictively to protection from biological hazards.

  19. Synthesis of single wall carbon nanotubes from a lamellar type ...

    Indian Academy of Sciences (India)

    Wintec

    These nanotubes are applicable to store more hydrogen. Keywords. AlPO4-L; single wall carbon nanotubes. 1. Introduction. Carbon nanotubes (Iijima 1991) are nano-scale structures formed by self assembly. They possess excellent chemical and physical properties (Rodney and Donald 1995; Chen et al 1998) that make ...

  20. Full HPV typing by a single restriction enzyme.

    Science.gov (United States)

    Santiago, Enrique; Camacho, Lucía; Junquera, Maria Luisa; Vázquez, Fernando

    2006-09-01

    Restriction fragment length polymorphism (RFLP) methods for genotyping genital human papillomavirus (HPV) are considered labor consuming and constrained by the reduced set of restriction enzymes capable of detecting specific mutations. However, we think that these methods have not taken full advantage of the high diversity of the known restriction enzymes. We have set out to find the best restriction enzyme for HPV typing. An extensive search for enzymes was carried out by combining statistical methods and database information. The search maximized the discrimination between high- and low-risk types by examining the sequence of the L1 gene flanked by primers MY09/11. Different electrophoretic resolutions and two variations of the RFLP method were considered. HpyCH4V is the best enzyme for discriminating between risk types. Moreover, HpyCH4V generates different patterns for virtually all the HPV types. The typical pattern consists of two or three fragments, which facilitates typing in mixed infections. The typing of a set of clinical samples confirmed the expectations. This result illustrates the possibilities of statistical methods to exploit the high diversity of restriction enzymes in order to classify samples in a pre-established hierarchy of types for which DNA sequences are known.

  1. Wood handbook : wood as an engineering material

    Science.gov (United States)

    Robert J. Ross; Forest Products Laboratory. USDA Forest Service.

    2010-01-01

    Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

  2. Synthesis of single wall carbon nanotubes from a lamellar type ...

    Indian Academy of Sciences (India)

    Wintec

    circular disc of fine copper mesh covered with collodion. Images were taken using a JEOL JSM-2000 EX electron microscope operated at an acceleration voltage of 200 kV. 3. Results and discussion. Figure 1 shows the as-synthesized AlPO4-L which was found to be of short range ordered lamellar type molecular ...

  3. Development of n- and p-type Doped Perovskite Single Crystals Using Solid-State Single Crystal Growth (SSCG) Technique

    Science.gov (United States)

    2017-10-09

    tried. Among them “n- and p-type doped” BaTiO3 single crystals have been successfully fabricated . And their bi- crystals containing a twin or twist...boundary are also fabricated using diffusion bonding process of two single crystal plates. These results demonstrate that the SSCG (solid-state...or Bridgman method have critical limitations; high production cost and compositional inhomogeneity throughout the crystal. These limitations result

  4. Wood and Other Materials Used to Construct Nonresidential Buildings - Canada

    Science.gov (United States)

    David B. McKeever; Joe Elling

    2014-01-01

    Low-rise nonresidential building construction is an important market in Canada for lumber, engineered wood products, structural wood panels, and nonstructural wood panels. This report examines wood products consumption in 2012 for construction of selected low-rise nonresidential buildings types that have six or fewer stories. Buildings with more than six stories are...

  5. Wood as an adherend

    Science.gov (United States)

    Bryan H. River; Charles B. Vick; Robert H. Gillespie

    1991-01-01

    Wood is a porous, permeable, hygroscopic, orthotropic, biological composite material of extreme chemical diversity and physical intricacy. Table 1.1 provides an overview of the may variables, including wood variables, that bear on the bonding and performance of wood in wood joints and wood-based materials. Of particular note is the fact that wood properties vary...

  6. Dietary traits of the late Early Pleistocene Bison menneri (Bovidae, Mammalia) from its type site Untermassfeld (Central Germany) and the problem of Pleistocene 'wood bison'

    Science.gov (United States)

    van Asperen, Eline N.; Kahlke, Ralf-Dietrich

    2017-12-01

    Over the course of the Early and early Middle Pleistocene, a climatic cooling trend led to the partial opening up of landscapes in the western Palaearctic. This led to a gradual replacement of browsers by grazers, whilst some herbivore species shifted their diet towards including more grass. Wear patterns of herbivore cheek teeth can inform our understanding of the timing and extent of this change and indicate levels of dietary plasticity. One of the indicator species of the faunal turnover is the first large-sized form of bison in the Palaearctic, Bison menneri. The dental mesowear of the palaeopopulation from the species' late Early Pleistocene type site of Untermassfeld in Central Germany and the Late Pleistocene B. priscus from Taubach, both from habitat mosaics of forested habitats and more open landscapes, have a mixed feeder profile similar to that of North American wood bison, which has a distinct preference for open habitats but occasionally consumes a high amount of browse as a fall-back food. In contrast, the grazer mesowear signature of early Middle Pleistocene B. schoetensacki voigtstedtensis from Voigtstedt indicates these animals likely did not regularly feed in the densely forested area around the site. The mesowear of B. schoetensacki from Süssenborn, in a more open environment, is similar to that of extant European bison. Both Pleistocene and extant bison are grazers to mixed feeders with relatively high tolerance of a suboptimal browsing diet. None of these species can be regarded as true 'wood bison'.

  7. The efficiency of different types of wood charcoal on increasing carbon content on surfaces of low carbon steel in the pack carburizing process

    Directory of Open Access Journals (Sweden)

    Narongsak Thammachot

    2014-09-01

    Full Text Available The purpose of this research is to compare the efficiency of five types of wood charcoal, eucalyptus, coconut shell, tamarind, bamboo and cassava root in increasing carbon content on surfaces of low carbon steel by the pack carburizing process. The experiment for pack carburized low carbon steel (grade AISI 1020 was conducted by using the different wood charcoals as carburizers, mixed with 10% limestone (by weight as the energizer. The carburizing temperature of 950°C, and carburizing times of 2, 4 and 6 hours were used in the experiment. After grinding, the specimens in each case were checked for carbon content by optical emission spectroscopy. Micro-Vickers hardness testing and microstructure inspections were carried out. The results of the experiment showed that the efficiency of eucalyptus charcoal as the carburizer (for increasing carbon content on surfaces of low carbon steel was higher than that of tamarind, cassava root, coconut shell and bamboo charcoals. The averages for carbon content were: 1.16, 1.06, 0.97, 0.83 and 0.77% respectively.

  8. Preservation of forest wood chips

    Energy Technology Data Exchange (ETDEWEB)

    Kofman, P.D.; Thomsen, I.M.; Ohlsson, C.; Leer, E.; Ravn Schmidt, E.; Soerensen, M.; Knudsen, P.

    1999-01-01

    As part of the Danish Energy Research Programme on biomass utilisation for energy production (EFP), this project concerns problems connected to the handling and storing of wood chips. In this project, the possibility of preserving wood chips of the Norway Spruce (Picea Abies) is addressed, and the potential improvements by anaerobic storage are tested. Preservation of wood chips aims at reducing dry matter losses from extensive heating during storage and to reduce production of fungal spores. Fungal spores pose a health hazards to workers handling the chips. Further the producers of wood chips are interested in such a method since it would enable them to give a guarantee for the delivery of homogeneous wood chips also during the winter period. Three different types of wood chips were stored airtight and further one of these was stored in accordance with normal practise and use as reference. The results showed that airtight storage had a beneficial impact on the quality of the chips: no redistribution of moisture, low dry matter losses, unfavourable conditions for microbial activity of most fungi, and the promotion of yeasts instead of fungi with airborne spores. Likewise the firing tests showed that no combustion problems, and no increased risk to the environment or to the health of staff is caused by anaerobic storage of wood chips. In all, the tests of the anaerobic storage method of forest wood chips were a success and a large-scale test of the method will be carried out in 1999. (au)

  9. Assessment of the wood waste resource and its position in the wood / wood-energy sector - Synthesis

    International Nuclear Information System (INIS)

    Guinard, Ludovic; Deroubaix, Gerard; Roux, Marie-Lise; Levet, Anne-Laure; Quint, Vincent

    2015-04-01

    The first objective of this study is to obtain a better knowledge of the 'wood wastes' issue, to propose a photography of the wood waste sector (productions, trades, consumptions), and then to elaborate different prospective scenarios on the use of wood waste volumes while taking into account possible evolutions on the medium or short term of the regulation and market of the wood/wood energy sector. The considered wastes come from industrial production, from the use of wood-based products, and from the end of life of products potentially containing wood. The authors present bibliographical sources and the adopted methodology, briefly describe the 'wood waste' system with its actors, and then report their assessment of wood wastes. They propose a global assessment as well as detailed assessments with respect to waste origins: wood trade and distribution, industries, craft, households and communities, building sector, public and private tertiary sector, packaging. They also address the collection and management of wood wastes by public services, and present the different types of valorisation (panel fabrication, energy, and others). They discuss exports, and then present different scenarios: a trend-based scenario, and two prospective scenarios with a priority to energetic valorisation or to material valorisation of wood wastes. These scenarios are compared

  10. The Statistics of wood assays for preservative retention

    Science.gov (United States)

    Patricia K. Lebow; Scott W. Conklin

    2011-01-01

    This paper covers general statistical concepts that apply to interpreting wood assay retention values. In particular, since wood assays are typically obtained from a single composited sample, the statistical aspects, including advantages and disadvantages, of simple compositing are covered.

  11. Single nucleotide polymorphisms in a cellulose synthase gene (PtoCesA3) are associated with growth and wood properties in Populus tomentosa.

    Science.gov (United States)

    Xu, Baohua; Tian, Jiaxing; Du, Qingzhang; Gong, Chenrui; Pan, Wei; Zhang, Deqiang

    2014-12-01

    In plants, the composition and organization of the cell wall determine cell shape, enable cell expansion, and affect the properties of woody tissues. Cellulose synthase (CesA) genes encode the enzymes involved in the synthesis of cellulose which is the major component of plant primary and secondary cell walls. Here, we isolated a full-length PtoCesA3 cDNA from the stem cambium tissue of Populus tomentosa. Tissue-specific expression profiling showed that PtoCesA3 is highly expressed during primary cell wall formation. Estimation of single nucleotide polymorphism (SNP) diversity and linkage disequilibrium (LD) revealed that PtoCesA3 harbors high SNP diversity (π(T) = 0.00995 and θ(w) = 0.0102) and low LD (r(2) ≥ 0.1, within 1,280 bp). Association analysis in a P. tomentosa association population (460 individuals) showed that seven SNPs (false discovery rate Q wood properties, explaining 4.09-7.02% of the phenotypic variance. All significant marker-trait associations were validated in at least one of the three smaller subsets (climatic regions) while five associations were repeated in the linkage population. Variation in RNA transcript abundance among genotypic classes of significant loci was also confirmed in the association or linkage populations. Identification of PtoCesA3 and examining its allelic polymorphisms using association studies open an avenue to understand the mechanism of cellulose synthesis in the primary cell wall and its effects on the properties of woody tissues.

  12. ROUGHNESS ON WOOD SURFACES AND ROUGHNESS MEASUREMENT METHODS

    OpenAIRE

    İsmail Aydın; Gürsel Çolakoğlu

    2003-01-01

    Some visual characteristics of wood such as color, pattern and texture determine the quality of manufactured products. Surface properties of wood material are important both in production and marketing after production. Initial studies related to the roughness of wood surface were begun in early 1950’s. However, no general agreed standardization can not have been developed for wood surfaces. Surface roughness of wood is function of the production process, product type and the natural anatomic...

  13. Significance of wood extractives for wood bonding.

    Science.gov (United States)

    Roffael, Edmone

    2016-02-01

    Wood contains primary extractives, which are present in all woods, and secondary extractives, which are confined in certain wood species. Extractives in wood play a major role in wood-bonding processes, as they can contribute to or determine the bonding relevant properties of wood such as acidity and wettability. Therefore, extractives play an immanent role in bonding of wood chips and wood fibres with common synthetic adhesives such as urea-formaldehyde-resins (UF-resins) and phenol-formaldehyde-resins (PF-resins). Extractives of high acidity accelerate the curing of acid curing UF-resins and decelerate bonding with alkaline hardening PF-resins. Water-soluble extractives like free sugars are detrimental for bonding of wood with cement. Polyphenolic extractives (tannins) can be used as a binder in the wood-based industry. Additionally, extractives in wood can react with formaldehyde and reduce the formaldehyde emission of wood-based panels. Moreover, some wood extractives are volatile organic compounds (VOC) and insofar also relevant to the emission of VOC from wood and wood-based panels.

  14. Tannins in tropical woods

    Energy Technology Data Exchange (ETDEWEB)

    Doat, J.

    1978-01-01

    A preliminary study was made of the chemistry of pyrogallol- and catecholtannins, their general properties and methods of extraction and determination. Three methods of estimation - Lowenthal, powdered hide and spectrophotometry - were compared using two control solutions, four samples of wood and one of bark. Using the empirical powdered hide method, tannins of both types were estimated in wood and bark of various tropical species (some separately and some as a mixture), Moroccan oaks (Quercus suber and Q. ilex), and European oak 9Q. petraea). Further tests were made on the wood and bark of the two mangrove species, Rhizophora mangle and R. racemosa, by subjecting them to successive extraction with a range of solvents. None of the woods tested had as much as the 10% of tannins considered necessary in economic sources. The bark of the two mangroves, of Eucalyptus urophylla and of Prosopis africana had tannin contents over 10% and the latter two species had very favorable tannin/non-tannin ratios. All the tropical species, with the probable exception of E. urophylla, had only catecholtannins. Only the oaks and E. urophylla bark gave positive results when tested for gallotannins.

  15. Variation in Trembling Aspen and White Spruce Wood Quality Grown in Mixed and Single Species Stands in the Boreal Mixedwood Forest

    Directory of Open Access Journals (Sweden)

    Francis De Araujo

    2015-05-01

    Full Text Available The Canadian boreal forest is largely represented by mixed wood forests of white spruce (Picea glauca (Moench Voss and trembling aspen (Populus tremuloides Michx. In this study, a total of 300 trees originating from three sites composed of trembling aspen and white spruce with varying compositions were investigated for wood quality traits: one site was composed mainly of aspen, one mainly of spruce and a third was a mixed site. Four wood quality traits were examined: wood density, microfibril angle (MFA, fibre characteristics, and cell wall chemistry. Social classes were also determined for each site in an attempt to provide a more in-depth comparison. Wood density showed little variation among sites for both species, with only significant differences occurring between social classes. The aspen site showed statistically lower MFAs than the aspen from the mixed site, however, no differences were observed when comparing spruce. Fibre characteristics were higher in the pure species sites for both species. There were no differences in carbohydrate contents across sites, while lignin content varied. Overall, the use of social classes did not refine the characterization of sites.

  16. Natural radionuclides and radiocaesium contained in wood

    International Nuclear Information System (INIS)

    Mahmoud, Kamal Reyad; El-Husseiny, Fathy Ahmed; Badran, Hussein Mahmoud

    2004-01-01

    The activity concentrations of natural ( 226 Ra, 232 Th and 40 K) and anthropogenic ( 137 Cs) radioactive elements in local and imported wood samples have been investigated during the last few years. Seven local and four imported wood types were measured. The activities of the natural isotopes in both local and imported wood samples were comparable. The Chernobyl accident didn't only affect European countries through contamination of the forested but also non-wood producing countries like Egypt. A fraction of the deposited fallout radionuclides has become incorporated into wood. Most of the imported samples (∼ 83%) showed measurable concentration of 137 Cs. The average 137 Cs activity levels in local and imported wood were 0.16 and 2.75 Bq/kg dry weight, respectively. The result of this study has its importance to many other wood-importing countries. (author)

  17. Single Microwave-Photon Detector using an Artificial Lambda-type Three-Level System

    Science.gov (United States)

    2016-01-11

    Single microwave -photon detector using an artificial Λ-type three-level system Kunihiro Inomata,1∗†, Zhirong Lin,1†, Kazuki Koshino,2, William D...are those of the author and are not necessarily endorsed by the United States Government. Single microwave -photon detector using an artificial Λ-type...in both the optical and the microwave domains. However, the energy of mi- crowave quanta are four to five orders of magnitude less than their optical

  18. Estimating Intervention Effects across Different Types of Single-Subject Experimental Designs: Empirical Illustration

    Science.gov (United States)

    Moeyaert, Mariola; Ugille, Maaike; Ferron, John M.; Onghena, Patrick; Heyvaert, Mieke; Beretvas, S. Natasha; Van den Noortgate, Wim

    2015-01-01

    The purpose of this study is to illustrate the multilevel meta-analysis of results from single-subject experimental designs of different types, including AB phase designs, multiple-baseline designs, ABAB reversal designs, and alternating treatment designs. Current methodological work on the meta-analysis of single-subject experimental designs…

  19. Finishes for Wood Decks

    Science.gov (United States)

    Mark Knaebe

    2013-01-01

    Wood decks have become an important part of residential construction. Wood decks can add versatile living space to a home and, with minimal maintenance, provide decades of use. However, wood decks are exposed to high levels of stress from severe weather conditions that shrink and swell the wood. Without proper maintenance, wood decks can develop problems such as checks...

  20. National Wood-fuel Programme 2000-2006. Activity Report 2000-2006

    International Nuclear Information System (INIS)

    2008-01-01

    When ADEME launched its Wood-fuel programme throughout all of France in late 1999, its aim was to guide this resource supply chain to maturity and stable development in all user sectors: domestic, multi-family housing, commercial/institutional and industrial applications. To this end the Wood-fuel Programme 2000-2006 was assigned objectives and endowed with significant financial means for studies and coordination in order to support and carry out general-interest projects, piloted by ADEME. The stated goal was to replace fossil fuels, avoid carbon emissions and establish quality assurance standards for household firewood and wood-fired devices. This report presents: 1 - the Wood Energy stakes for the environment, for employment, and for the economy, the biomass energy net benefits; 2 - the Wood Energy key figures: Production and consumption, Single-family homes and wood heating, Breakdown of types of devices used, Sales of wood-fired devices, Number of housing/institutional boilers in use, Number of industrial boilers in use; 3 - the Wood Energy objectives: Domestic heating, Industrial boiler plants, District heating for housing/institutional/commercial uses; 4 - the Wood Energy program operation: Program coordination by ADEME, Partnerships and State-Region planning agreements, 2000-2006 funding system (modified in 2004) and Other financial instruments; 5 - the 2000-2006 assessment: Main results, Conclusions and recommendations, Evaluation contributions: five key points, Evaluation of employment in the solid biofuels supply chain, Supply for community, institutional and commercial boilers; 6 - Information and communication: Initiatives supported or accompanied by ADEME between 2000 and 2004, Publications supported by ADEME. In appendix: fuels and energy content, regional assessments, national research program on bio-energies - PNRB 2006 (Review and stakes, PNRB results in 2006), wood heating R and D, studies funded by ADEME, 2006 ADEME's correspondents, glossary

  1. Domestic Wood Burning in a Residential Area: PM2.5 Trace Elements and Black Smoke

    International Nuclear Information System (INIS)

    Molnar, P.; Gustafson, P.; Johannesson, S.; Barregaard, L.; Saellsten, G.; Boman, J.

    2005-01-01

    Indoor and outdoor levels of PM2.5 have been studied in a residential area in Hagfors, a small town in Sweden. The sampling took place during typical Swedish winter conditions with sub-zero temperatures and full snow cover between February 10th and Mars 6th, 2003. The area consists of single houses having different heating systems. Some of the houses are heated by burning wood; some use heat pumps while others use direct electrical heating. 13 houses burning wood in boilers or similar for heating and 10 houses heated by other means but situated in the same area were selected for this study. Only houses without tobacco smoke were selected since this is one of the major sources of indoor particles. The objectives of the study were to identify levels and differences in composition of aerosol particles outdoors and inside houses with boilers using wood as fuel and houses heated in other ways. For K, Ca, Mn, Zn and Rb significantly higher (p < 0.05) indoor concentration for wood burners were found. The elements most often referred to as markers for wood burning are K and Zn. In addition, Si, S, Cl, Br and Rb are also mentioned as markers (Hedberg et al., 2002, Moloi et al., 2003). Black smoke was linked to wood burning, although not fully significant (p-value 0.07), as seen in figure 1a. Within the wood-burning group, some houses have concentrations comparable to the concentrations in the houses where no wood is used, while the others have much higher concentrations. These houses also have higher concentrations of K compared to the other wood burners. The possible reasons are different types of wood burning appliances and their placement in the houses as well as possible leakage. Sulphur, although sometimes linked to wood burning, shows no relationship to wood burning in this study. In figure 1b it can be seen that the indoor concentrations of sulphur is clearly lower compared to outdoor concentrations and that the levels indoors do not differ between wood and non-wood

  2. Wood combustion particles induce adverse effects to normal and diseased airway epithelia.

    Science.gov (United States)

    Krapf, Manuel; Künzi, Lisa; Allenbach, Sandrine; Bruns, Emily A; Gavarini, Ilaria; El-Haddad, Imad; Slowik, Jay G; Prévôt, André S H; Drinovec, Luka; Močnik, Griša; Dümbgen, Lutz; Salathe, Matthias; Baumlin, Nathalie; Sioutas, Constantinos; Baltensperger, Urs; Dommen, Josef; Geiser, Marianne

    2017-04-19

    Residential wood burning is a major source of poorly characterized, deleterious particulate matter, whose composition and toxicity may vary with wood type, burning condition and photochemical age. The causative link between ambient wood particle constituents and observed adverse health effects is currently lacking. Here we investigate the relationship between chemical properties of primary and atmospherically aged wood combustion particles and acute toxicity in human airway epithelial cells. Emissions from a log wood burner were diluted and injected into a smog chamber for photochemical aging. After concentration-enrichment and removal of oxidizing gases, directly emitted and atmospherically aged particles were deposited on cell cultures at the air-liquid interface for 2 hours in an aerosol deposition chamber mimicking physiological conditions in lungs. Cell models were fully differentiated normal and diseased (cystic fibrosis and asthma) human bronchial epithelia (HBE) and the bronchial epithelial cell line BEAS-2B. Cell responses were assessed at 24 hours after aerosol exposure. Atmospherically relevant doses of wood combustion particles significantly increased cell death in all but the asthma cell model. Expression of oxidative stress markers increased in HBE from all donors. Increased cell death and inflammatory responses could not be assigned to a single chemical fraction of the particles. Exposure to primary and aged wood combustion particles caused adverse effects to airway epithelia, apparently induced by several interacting components.

  3. Stress-wave velocity of wood-based panels: effect of moisture, product type, and material direction

    Science.gov (United States)

    Guangping Han; Qinglin Wu; Xiping Wang

    2006-01-01

    The effect of moisture on longitudinal stress-wave velocity (SWV), bending stiffness. and bending strength of commercial oriented strandboard, plywood. particleboard. and southern pine lumber was evaluated. It was shown that the stress-wave verocity decreased in general with increases in panel moisture content (MC). At a given MC level. SWV varied with panel type and...

  4. Integration of heat treatment of wood with cogeneration production and district heating; Vaermebehandling av trae integrerad med kraftvaermeproduktion och fjaerrvaerme

    Energy Technology Data Exchange (ETDEWEB)

    Delin, Lennart; Essen, Henrik (AaF, Stockholm (Sweden))

    2011-05-15

    Heat treatment of wood changes the properties of wood so that the moisture uptake is reduced and the wood movements are reduced at variations in the ambient air humidity. The wood gets an increased resistance to rot and can therefore replace impregnated wood in certain applications. Heat treated wood is however not suitable for direct contact with soil. The strength is also reduced by heat treatment, so it is not recommended for supporting constructions. No additives whatsoever are used in the treatment, so the heat treated wood is very advantageous from an environmental point of view. The wood is dried completely at the heat treatment and heated to about 200 deg C. The question has hence been put, if it is advantageous to collocate a heat treatment plant with district heating or a power cogeneration plant. The aim of the study is to assess the value of such a collocation. Existing heat treatment plants are both few and small and the calculations have hence been made for how a large plant could be designed. A market study is included to assess the market for this type of plants. This shows that the present market for heat treated wood is very small. A full scale treatment plant of the type discussed in this study could probably not be built, since even single plants of this size would require a too large part of the market. The potential to replace impregnated wood is on the other hand very large. The cost for large scale heat treatment should be significantly lower than for impregnated wood and the cost for handling hazardous waste (which impregnated wood is classified as) is also removed. There should therefore be a potential for a future much larger volume of heat treated wood. The study shows that the energetic profit of collocation of a heat treatment plant for wood with district heating or power cogeneration plants is of lower importance. Maximally about 0.5 MSEK/year can be saved for a 25 000 m3/year plant. The initial drying of all sawn lumber has much more

  5. Rapid single step subcloning procedure by combined action of type II and type IIs endonucleases with ligase

    Directory of Open Access Journals (Sweden)

    Klingenspor Martin

    2007-11-01

    Full Text Available Abstract Background The subcloning of a DNA fragment from an entry vector into a destination vector is a routinely performed task in molecular biology labs. Results We here present a novel benchtop procedure to achieve rapid recombination into any destination vector of choice with the sole requirement of an endonuclease recognition site. The method relies on a specifically designed entry vector and the combined action of type II and type IIs endonucleases with ligase. The formulation leads to accumulation of a single stable cloning product representing the desired insert carrying destination vector. Conclusion The described method provides a fast single step procedure for routine subcloning from an entry vector into a series of destination vectors with the same restriction enzyme recognition site.

  6. Rapid single step subcloning procedure by combined action of type II and type IIs endonucleases with ligase.

    Science.gov (United States)

    Fromme, Tobias; Klingenspor, Martin

    2007-11-26

    The subcloning of a DNA fragment from an entry vector into a destination vector is a routinely performed task in molecular biology labs. We here present a novel benchtop procedure to achieve rapid recombination into any destination vector of choice with the sole requirement of an endonuclease recognition site. The method relies on a specifically designed entry vector and the combined action of type II and type IIs endonucleases with ligase. The formulation leads to accumulation of a single stable cloning product representing the desired insert carrying destination vector. The described method provides a fast single step procedure for routine subcloning from an entry vector into a series of destination vectors with the same restriction enzyme recognition site.

  7. The use of a single volar locking plate for AO C3-type distal radius fractures.

    Science.gov (United States)

    Earp, Brandon E; Foster, Brian; Blazar, Philip E

    2015-12-01

    A single volar locking plate (VLP) is now frequently used for open reduction and internal fixation (ORIF) of many types of distal radius fractures. Comminuted intra-articular distal radius fractures (AO C3-type) are typically the most challenging to surgically treat. No studies directly address the adequacy of a VLP alone for maintaining reduction of AO C-type fractures. We hypothesized that a single VLP provides an effective method for maintaining reduction for these fractures. We retrospectively evaluated radiographs of a series of AO C-type fractures. Seventy-seven patients with 77 AO C3-type fractures were identified from billing records and were eligible for the study. All patients were treated by fellowship-trained hand surgeons. Radiographs at the time of union were compared to those from immediately postoperatively. Sixty-nine of 77 (89.6 %) fractures treated with VLP fixation alone for AO C3-type distal radius fractures united without loss of reduction. Eight of 77 (10.4 %) patients treated with VLP for AO C3 fractures lost reduction. The most common fracture fragment to lose reduction was the lunate fossa (5 of 8); loss of reduction of the scaphoid fossa die-punch fragment (2 of 8) and the radial styloid (1 of 8) were also seen. The majority (89.6 %) of AO C3-type fractures treated with a single volar locking plate come to union without loss of reduction. Level IV.

  8. EFFECT OF LAMINATE INCLUSION AND THE TYPE OF ADHESIVE IN THE PROPERTIES OF OSB PANELS OF THE WOOD FROM Pinus oocarpa

    Directory of Open Access Journals (Sweden)

    José Benedito Guimarães júnior

    2012-11-01

    Full Text Available The aim of the study was to evaluate the influence of laminate inclusion and the type of adhesive on the physical and mechanical properties of OSB panels produced from the wood of Pinus oocarpa. The experimental design consisted of four treatments. Laminateinclusion and urea-formaldehyde and phenol-formaldehyde adhesives applied in combination with the panel layer were evaluated. For each treatment, three panels with nominal density of 0.65 g.cm-3, 1% to 6% paraffin and adhesive were produced. In the manufacturing of thepanels, temperature of 180 ° C, pressure of 3.95 MPa and pressing time of 8 minutes were adopted. From the results it is concluded that: the species Pinus oocarpa has great potential for use in the production of OSB panels; the laminate inclusion resulted in significant improvement in the properties of water absorption and thickness swelling after immersion for two hours, as well as in the modulus of elasticity and modulus of rupture in parallel direction; and the panels made with urea-formaldehyde adhesives in the core and phenol-formaldehydeon the faces statistically equal to panels only with the phenol-formaldehyde adhesive in statistically, except in the internal bonding property.

  9. ROUGHNESS ON WOOD SURFACES AND ROUGHNESS MEASUREMENT METHODS

    Directory of Open Access Journals (Sweden)

    İsmail Aydın

    2003-04-01

    Full Text Available Some visual characteristics of wood such as color, pattern and texture determine the quality of manufactured products. Surface properties of wood material are important both in production and marketing after production. Initial studies related to the roughness of wood surface were begun in early 1950’s. However, no general agreed standardization can not have been developed for wood surfaces. Surface roughness of wood is function of the production process, product type and the natural anatomical properties of wood. Contact and non-contact tracing methods are used to measure of wood surface roughness. Surface roughness also affects the gluability and wettability of wood surfaces. The success in finishing also depends on the surface roughness of wood.

  10. Discover the benefits of residential wood heating

    International Nuclear Information System (INIS)

    2003-01-01

    This publication described how residential wood-heating systems are being used to reduce energy costs and increase home comfort. Biomass energy refers to all forms are renewable energy that is derived from plant materials. The source of fuel may include sawmills, woodworking shops, forest operations and farms. The combustion of biomass is also considered to be carbon dioxide neutral, and is not considered to be a major producer of greenhouse gases (GHG) linked to global climate change. Wood burning does, however, release air pollutants, particularly if they are incompletely burned. Incomplete combustion of wood results in dense smoke consisting of toxic gases. Natural Resources Canada helped create new safety standards and the development of the Wood Energy Technical Training Program to ensure that all types of wood-burning appliances are installed correctly and safely to reduce the risk of fire and for effective wood heating. In Canada, more than 3 million families heat with wood as a primary or secondary heating source in homes and cottages. Wood heating offers security from energy price fluctuations and electrical power failures. This paper described the benefits of fireplace inserts that can transform old fireplaces into modern heating systems. It also demonstrated how an add-on wood furnace can be installed next to oil furnaces to convert an oil-only heating system to a wood-oil combination system, thereby saving thousands of dollars in heating costs. Wood pellet stoves are another wood burning option. The fuel for the stoves is produced from dried, finely ground wood waste that is compressed into hard pellets that are loaded into a hopper. The stove can run automatically for up to 24 hours. New high-efficiency advanced fireplaces also offer an alternative heating system that can reduce heating costs while preserving Canada's limited supply of fossil fuels such as oil and gas. 13 figs

  11. Reactivity and burnout of wood fuels

    DEFF Research Database (Denmark)

    Dall'Ora, Michelangelo

    This thesis deals with the combustion of wood in pulverised fuel power plants. In this type of boiler, the slowest step in the wood conversion process is char combustion, which is one of the factors that not only determine the degree of fuel burnout, but also affect the heat release profile...

  12. Scarcity on the market for wood wastes

    International Nuclear Information System (INIS)

    De Boer, A.

    2004-01-01

    An overview is given of the market for wood wastes in the Netherlands and how this affects the targets to use biomass. Several types of biomass must be imported, not only wood wastes, but also e.g. olive stones and cacao shells [nl

  13. Wood Species Recognition System

    OpenAIRE

    Bremananth R; Nithya B; Saipriya R

    2009-01-01

    The proposed system identifies the species of the wood using the textural features present in its barks. Each species of a wood has its own unique patterns in its bark, which enabled the proposed system to identify it accurately. Automatic wood recognition system has not yet been well established mainly due to lack of research in this area and the difficulty in obtaining the wood database. In our work, a wood recognition system has been designed based on pre-processing te...

  14. LCA-based optimization of wood utilization under special consideration of a cascading use of wood.

    Science.gov (United States)

    Höglmeier, Karin; Steubing, Bernhard; Weber-Blaschke, Gabriele; Richter, Klaus

    2015-04-01

    Cascading, the use of the same unit of a resource in multiple successional applications, is considered as a viable means to improve the efficiency of resource utilization and to decrease environmental impacts. Wood, as a regrowing but nevertheless limited and increasingly in demand resource, can be used in cascades, thereby increasing the potential efficiency per unit of wood. This study aims to assess the influence of cascading wood utilization on optimizing the overall environmental impact of wood utilization. By combining a material flow model of existing wood applications - both for materials provision and energy production - with an algebraic optimization tool, the effects of the use of wood in cascades can be modelled and quantified based on life cycle impact assessment results for all production processes. To identify the most efficient wood allocation, the effects of a potential substitution of non-wood products were taken into account in a part of the model runs. The considered environmental indicators were global warming potential, particulate matter formation, land occupation and an aggregated single score indicator. We found that optimizing either the overall global warming potential or the value of the single score indicator of the system leads to a simultaneous relative decrease of all other considered environmental impacts. The relative differences between the impacts of the model run with and without the possibility of a cascading use of wood were 7% for global warming potential and the single score indicator, despite cascading only influencing a small part of the overall system, namely wood panel production. Cascading led to savings of up to 14% of the annual primary wood supply of the study area. We conclude that cascading can improve the overall performance of a wood utilization system. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Inactivation of single-chain urokinase-type plasminogen activator by thrombin in human subjects

    NARCIS (Netherlands)

    Braat, E. A.; Levi, M. [=Marcel M.; Bos, R.; Haverkate, F.; Lassen, M. R.; de Maat, M. P.; Rijken, D. C.

    1999-01-01

    Thrombin cleaves single-chain urokinase-type plasminogen activator (scu-PA) into a virtually inactive two-chain form (tcu-PA/T), a process that may protect a blood clot from early fibrinolysis. It is not known under what circumstances tcu-PA/T can be generated in vivo. We have studied the occurrence

  16. Identifying types of physical activity with a single accelerometer: Evaluating laboratory trained algorithms in daily life

    NARCIS (Netherlands)

    Cuba Gyllensten, I.; Bonomi, A.G.

    2011-01-01

    Accurate identification of physical activity types has been achieved in laboratory conditions using single-site accelerometers and classification algorithms. This methodology is then applied to free-living subjects to determine activity behaviour. This study aimed at analysing the reproducibility of

  17. Age-dependent radial increases in wood specific gravity of tropical pioneers in Costa Rica

    Science.gov (United States)

    Bruce G. Williamson; Michael C. Wiemann

    2010-01-01

    Wood specific gravity is the single best descriptor of wood functional properties and tree life-history traits, and it is the most important variable in estimating carbon stocks in forests. Tropical pioneer trees produce wood of increasing specific gravity across the trunk radius as they grow in stature. Here, we tested whether radial increases in wood specific gravity...

  18. Esthetic outcome of single implant crowns following type 1 and type 3 implant placement: a systematic review.

    Science.gov (United States)

    Shi, Jun-Yu; Wang, Ren; Zhuang, Long-Fei; Gu, Ying-Xin; Qiao, Shi-Chong; Lai, Hong-Chang

    2015-07-01

    The aim of the current review was to systematically appraise the esthetic outcome of soft tissue around single implant crowns following type 1 and type 3 implants placement in published dental literature. A PubMed, Embase, and the Cochrane Central Register of Controlled Trials search up to March 2013 was conducted for articles published in the dental literature and limited to human trials with no language restricted. Furthermore, the reference lists of related articles were systematically screened, and additional manual searches were also performed. The primary outcome was pink esthetics score (PES). The electronic search in the database of PubMed, Embase, and the Cohrane Central Register of Controlled Trials resulted in the identification of 463 titles. These titles were initially screened by the two independent reviewers for possible inclusion. Screening the abstracts and titles led to 28 articles for future full-text consideration. From these articles, 18 studies were excluded. Manual search identified one article. After quality assessment, eight studies were included in this review. This review showed that no significant difference of PES index could be found between type 1 and type 3 implant placement. According to the current evidence, short-term esthetic outcomes of peri-implant soft tissue did not show significant difference following type 1 and type 3 implants placement with well-selected patients. However, caution should be taken for clinicians to extrapolate this result to all types of patients, as more randomized clinical trials are needed for long-term soft-tissue esthetic outcome in patients with high esthetic risk following type 1 implant placement. PES frequency, peri-implant condition and other risk factors for peri-implantitis are recommended to be reported for future studies. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  19. Scheduling of hybrid types of machines with two-machine flowshop as the first type and a single machine as the second type

    Science.gov (United States)

    Hsiao, Ming-Chih; Su, Ling-Huey

    2018-02-01

    This research addresses the problem of scheduling hybrid machine types, in which one type is a two-machine flowshop and another type is a single machine. A job is either processed on the two-machine flowshop or on the single machine. The objective is to determine a production schedule for all jobs so as to minimize the makespan. The problem is NP-hard since the two parallel machines problem was proved to be NP-hard. Simulated annealing algorithms are developed to solve the problem optimally. A mixed integer programming (MIP) is developed and used to evaluate the performance for two SAs. Computational experiments demonstrate the efficiency of the simulated annealing algorithms, the quality of the simulated annealing algorithms will also be reported.

  20. Cell type discovery and representation in the era of high-content single cell phenotyping.

    Science.gov (United States)

    Bakken, Trygve; Cowell, Lindsay; Aevermann, Brian D; Novotny, Mark; Hodge, Rebecca; Miller, Jeremy A; Lee, Alexandra; Chang, Ivan; McCorrison, Jamison; Pulendran, Bali; Qian, Yu; Schork, Nicholas J; Lasken, Roger S; Lein, Ed S; Scheuermann, Richard H

    2017-12-21

    A fundamental characteristic of multicellular organisms is the specialization of functional cell types through the process of differentiation. These specialized cell types not only characterize the normal functioning of different organs and tissues, they can also be used as cellular biomarkers of a variety of different disease states and therapeutic/vaccine responses. In order to serve as a reference for cell type representation, the Cell Ontology has been developed to provide a standard nomenclature of defined cell types for comparative analysis and biomarker discovery. Historically, these cell types have been defined based on unique cellular shapes and structures, anatomic locations, and marker protein expression. However, we are now experiencing a revolution in cellular characterization resulting from the application of new high-throughput, high-content cytometry and sequencing technologies. The resulting explosion in the number of distinct cell types being identified is challenging the current paradigm for cell type definition in the Cell Ontology. In this paper, we provide examples of state-of-the-art cellular biomarker characterization using high-content cytometry and single cell RNA sequencing, and present strategies for standardized cell type representations based on the data outputs from these cutting-edge technologies, including "context annotations" in the form of standardized experiment metadata about the specimen source analyzed and marker genes that serve as the most useful features in machine learning-based cell type classification models. We also propose a statistical strategy for comparing new experiment data to these standardized cell type representations. The advent of high-throughput/high-content single cell technologies is leading to an explosion in the number of distinct cell types being identified. It will be critical for the bioinformatics community to develop and adopt data standard conventions that will be compatible with these new

  1. Finite Element Analysis of Doorframe Structure of Single Oblique Pole Type in Container Crane

    Science.gov (United States)

    Cheng, X. F.; Wu, F. Q.; Tang, G.; Hu, X.

    2017-07-01

    Compared with the composite type, the single oblique pole type has more advantages, such as simple structure, thrift steel and high safe overhead clearance. The finite element model of the single oblique pole type is established in nodes by ANSYS, and more details are considered when the model is simplified, such as the section of Girder and Boom, torque in Girder and Boom occurred by Machinery house and Trolley, density according to the way of simplification etc. The stress and deformation of ten observation points are compared and analyzed, when the trolley is in nine dangerous positions. Based on the result of analysis, six dangerous points are selected to provide reference for the detection and evaluation of container crane.

  2. Single Muscle Fiber Proteomics Reveals Fiber-Type-Specific Features of Human Muscle Aging

    Directory of Open Access Journals (Sweden)

    Marta Murgia

    2017-06-01

    Full Text Available Skeletal muscle is a key tissue in human aging, which affects different muscle fiber types unequally. We developed a highly sensitive single muscle fiber proteomics workflow to study human aging and show that the senescence of slow and fast muscle fibers is characterized by diverging metabolic and protein quality control adaptations. Whereas mitochondrial content declines with aging in both fiber types, glycolysis and glycogen metabolism are upregulated in slow but downregulated in fast muscle fibers. Aging mitochondria decrease expression of the redox enzyme monoamine oxidase A. Slow fibers upregulate a subset of actin and myosin chaperones, whereas an opposite change happens in fast fibers. These changes in metabolism and sarcomere quality control may be related to the ability of slow, but not fast, muscle fibers to maintain their mass during aging. We conclude that single muscle fiber analysis by proteomics can elucidate pathophysiology in a sub-type-specific manner.

  3. Wood pole overhead lines

    CERN Document Server

    Wareing, Brian

    2005-01-01

    This new book concentrates on the mechanical aspects of distribution wood pole lines, including live line working, environmental influences, climate change and international standards. Other topics include statutory requirements, safety, profiling, traditional and probabilistic design, weather loads, bare and covered conductors, different types of overhead systems, conductor choice, construction and maintenance. A section has also been devoted to the topic of lightning, which is one of the major sources of faults on overhead lines. The book focuses on the effects of this problem and the strate

  4. Firing with wood chips in heating and cogeneration plants

    International Nuclear Information System (INIS)

    Kofman, P.D.

    1992-01-01

    The document was produced for use as detailed teaching material aimed at spreading information on the use of wood chips as fuel for heating and cogeneration plants. It includes information and articles on wood fuels generally, combustion values, chopping machines, suppliers, occupational health hazards connected with the handling of wood chips, measuring amounts, the selection of types, prices, ash, environmental aspects and information on the establishment of a wood-chip fired district heating plant. (AB)

  5. Wood-based composite materials : panel products, glued-laminated timber, structural composite lumber, and wood-nonwood composite materials

    Science.gov (United States)

    Nicole M. Stark; Zhiyong Cai; Charles Carll

    2010-01-01

    This chapter gives an overview of the general types and composition of wood-based composite products and the materials and processes used to manufacture them. It describes conventional wood-based composite panels and structural composite materials intended for general construction, interior use, or both. This chapter also describes wood–nonwood composites. Mechanical...

  6. Woods from the Miocene Bakate Formation, Ethiopia : anatomical characteristics, estimates of original specific gravity and ecological inferences

    Science.gov (United States)

    E.A. Wheeler; M.C. Wiemann; J.G. Fleagle

    2007-01-01

    An assemblage of permineralized woods from the Miocene Bakate Formation, Fejej Plain, Ethiopia, is described. This assemblage of twelve wood types differs from other Miocene wood assemblages known from Ethiopia. Cell wall percentages of the woods were determined to estimate the original specific gravities of the woods in order to better understand the Miocene...

  7. Studies on polyphenols and lignin of Astronium urundeuva wood

    Directory of Open Access Journals (Sweden)

    Morais Sérgio A.L.

    1999-01-01

    Full Text Available An Astronium urundeuva ball-milled wood sample was successively extracted with benzene, benzene-ethanol (2:1, v/v-1, chloroform, and water in a soxhlet apparatus. The extracted wood was air-dried giving the residue A that was then treated with ketone-water (9:1, in a soxhlet apparatus. From the ketone-water extract was precipitated the milled wood lignin (MWL. With exception of MWL, the extract contents summed up 18.19% (o.d.w.. The Klason lignin content of A and the methoxyl content of the MWL were 23.84% and 19.00%, respectively. Another sample of A gave hardly and easily hydrolysable polysaccharide contents of 34.86% and 18.81%, respectively. A second sample of ball-milled wood was submitted to a single extraction with methanol, at room temperature, affording the methanol extract B (23.85% o.d.w.. Liquid and solid state 13C-NMR spectroscopies indicated that B is mainly constituted by proanthocyanidins of profisetinidin and prorobinetidin types.

  8. Multicolor imaging of cancer cells with fluorophore-tagged aptamers for single cell typing.

    Science.gov (United States)

    Wang, Song; Kong, Hao; Gong, Xiaoyun; Zhang, Sichun; Zhang, Xinrong

    2014-08-19

    The discrimination of the type of cancer cells remains challenging due to the subtle differences in their expression of membrane receptors. In this work, we developed a multicolor cell imaging method for distinguishing the type of cancer cells with fluorophore-tagged aptamers. We found that the interaction between aptamers and cancer cells was affected by both of the sequence of aptamers and the labeled dyes. As the co-ownership of biomarkers for different cancer cell lines, the fluorophore-tagged aptamers interacted with different cancer cell lines in different degree, resulting in a distinct color to discriminate the type of cancer cells at single cell level. Taking advantage of the cross-reactive ability of the fluorophore-tagged aptamers, we could not only distinguish the cancerous cells quickly from large quantities of noncancerous cells, but also identify the type of the cancerous cells. This work has potential application for cancer diagnostic and therapy in the future.

  9. Thermopower of beech wood biocarbon

    Science.gov (United States)

    Smirnov, I. A.; Smirnov, B. I.; Orlova, T. S.; Sulkovski, Cz.; Misiorek, H.; Jezowski, A.; Muha, J.

    2011-11-01

    This paper reports on measurements of the thermopower S of high-porosity samples of beech wood biocarbon with micron-sized sap pores aligned with the tree growth direction. The measurements have been performed in the temperature range 5-300 K. The samples have been fabricated by pyrolysis of beech wood in an argon flow at different carbonization temperatures ( T carb). The thermopower S has been measured both along and across the sap pores, thus offering a possibility of assessing its anisotropy. The curves S( T carb) have revealed a noticeable increase of S for T carb biocarbons, which suggests that for T carb ˜ 1000°C they undergo a phase transition of the insulator-(at T carb 1000°C) type. The existence of this transition is attested also by the character of the temperature dependences S( T) of beech wood biocarbon samples prepared at T carb above and below 1000°C.

  10. Structural modeling of dahlia-type single-walled carbon nanohorn aggregates by molecular dynamics.

    Science.gov (United States)

    Hawelek, L; Brodka, A; Dore, John C; Hannon, Alex C; Iijima, S; Yudasaka, M; Ohba, T; Kaneko, K; Burian, A

    2013-09-19

    The structure of dahlia-type single-walled carbon nanohorn aggregates has been modeled by classical molecular dynamics simulations, and the validity of the model has been verified by neutron diffraction. Computer-generated models consisted of an outer part formed from single-walled carbon nanohorns with diameters of 20-50 Å and a length of 400 Å and an inner turbostratic graphite-like core with a diameter of 130 Å. The diffracted intensity and the pair correlation function computed for such a constructed model are in good agreement with the neutron diffraction experimental data. The proposed turbostratic inner core explains the occurrence of the additional (002) and (004) graphitic peaks in the diffraction pattern of the studied sample and provides information about the interior structure of the dahlia-type aggregates.

  11. RADIAL VELOCITIES OF GALACTIC O-TYPE STARS. II. SINGLE-LINED SPECTROSCOPIC BINARIES

    International Nuclear Information System (INIS)

    Williams, S. J.; Gies, D. R.; Hillwig, T. C.; McSwain, M. V.; Huang, W.

    2013-01-01

    We report on new radial velocity measurements of massive stars that are either suspected binaries or lacking prior observations. This is part of a survey to identify and characterize spectroscopic binaries among O-type stars with the goal of comparing the binary fraction of field and runaway stars with those in clusters and associations. We present orbits for HDE 308813, HD 152147, HD 164536, BD–16°4826, and HDE 229232, Galactic O-type stars exhibiting single-lined spectroscopic variation. By fitting model spectra to our observed spectra, we obtain estimates for effective temperature, surface gravity, and rotational velocity. We compute orbital periods and velocity semiamplitudes for each system and note the lack of photometric variation for any system. These binaries probably appear single-lined because the companions are faint and because their orbital Doppler shifts are small compared to the width of the rotationally broadened lines of the primary.

  12. Properties of Wood Fibre-Polypropylene Composites: Effect of Wood Fibre Source

    Science.gov (United States)

    Butylina, Svetlana; Martikka, Ossi; Kärki, Timo

    2011-04-01

    This study examined the effect of type of wood fibre source on the physical and mechanical properties of wood fibre-polypropylene composites. Wood flour, fibres of heat-treated wood and pellets were used as sources of wood fibres in the manufacturing process. All studied wood fibre-polypropylene composites were made from 75% wood, 22% recycled polypropylene (PP) and 3% maleated polypropylene (MAPP). Wood fibre-polypropylene composites were compounded in a conical twin-screw extruder. Water absorption and thickness swelling were studied. Mechanical properties of the composites were characterised by tensile, flexural, and impact testing. Micromechanical deformation processes were investigated using scanning electron microscopy done on the fractured surfaces of broken samples. The durability of composites exposed to three accelerated cycles of water immersion, freezing and thawing was examined. The results showed that the density of the composites was a key factor governing water absorption and thickness swelling. A significant improvement in tensile strength, flexural strength, and Charpy impact strength was observed for composites reinforced with heat-treated fibre compared to composites reinforced with pellets and especially to wood flour reinforced composites. The flexural strength and dimensional stability performance reduced after exposure to freeze-thaw cycling for all composites, but the degree of these changes was dependent on the wood fibre source.

  13. Comprehensive Identification and Spatial Mapping of Habenular Neuronal Types Using Single-Cell RNA-Seq.

    Science.gov (United States)

    Pandey, Shristi; Shekhar, Karthik; Regev, Aviv; Schier, Alexander F

    2018-04-02

    The identification of cell types and marker genes is critical for dissecting neural development and function, but the size and complexity of the brain has hindered the comprehensive discovery of cell types. We combined single-cell RNA-seq (scRNA-seq) with anatomical brain registration to create a comprehensive map of the zebrafish habenula, a conserved forebrain hub involved in pain processing and learning. Single-cell transcriptomes of ∼13,000 habenular cells with 4× cellular coverage identified 18 neuronal types and dozens of marker genes. Registration of marker genes onto a reference atlas created a resource for anatomical and functional studies and enabled the mapping of active neurons onto neuronal types following aversive stimuli. Strikingly, despite brain growth and functional maturation, cell types were retained between the larval and adult habenula. This study provides a gene expression atlas to dissect habenular development and function and offers a general framework for the comprehensive characterization of other brain regions. Copyright © 2018 Elsevier Ltd. All rights reserved.

  14. Charge collection measurements in single-type column 3D sensors

    International Nuclear Information System (INIS)

    Scaringella, M.; Polyakov, A.; Sadrozinski, H.F.-W.; Bruzzi, M.; Tosi, C.; Boscardin, M.; Piemonte, C.; Pozza, A.; Ronchin, S.; Zorzi, N.; Dalla Betta, G.-F.

    2007-01-01

    We report on charge collection studies on 3D silicon detectors of single-type column n-diffusions in p-substrate, configured either as strip or as pad detectors. The charge is generated by penetrating beta particles from a 90 Sr source which, together with a scintillation counter, serves as an electron telescope. The charge collection as a function of bias voltage is compared with the depletion thickness derived from the measured C-V characteristics

  15. Charge collection measurements with p-type Magnetic Czochralski silicon single pad detectors

    International Nuclear Information System (INIS)

    Tosi, C.; Bruzzi, M.; Macchiolo, A.; Scaringella, M.; Petterson, M.K.; Sadrozinski, H.F.-W.; Betancourt, C.; Manna, N.; Creanza, D.; Boscardin, M.; Piemonte, C.; Zorzi, N.; Borrello, L.; Messineo, A.

    2007-01-01

    The charge collected from beta source particles in single pad detectors produced on p-type Magnetic Czochralski (MCz) silicon wafers has been measured before and after irradiation with 26 MeV protons. After a 1 MeV neutron equivalent fluence of 1x10 15 cm -2 the collected charge is reduced to 77% at bias voltages below 900 V. This result is compared with previous results from charge collection measurements

  16. Identification of soybean proteins from a single cell type: The root hair

    Energy Technology Data Exchange (ETDEWEB)

    Brechenmacher, Laurent; Nguyen, Tran H.; Hixson, Kim K.; Libault, Marc; Aldrich, Joshua T.; Pasa-Tolic, Ljiljana; Stacey, Gary

    2012-11-01

    Root hairs are a terminally differentiated single cell type, mainly involved in water and nutrient uptake from the soil. The soybean root hair cell represents an excellent model for the study of single cell systems biology. In this study, we identified 5702 proteins, with at least two peptides, from soybean root hairs using an accurate mass and time tag approach, establishing the most comprehensive proteome reference map of this single cell type. We also showed that trypsin is the most appropriate enzyme for soybean proteomic studies by performing an in silico digestion of the soybean proteome database using different proteases. Although the majority of proteins identified in this study are involved in basal metabolism, the function of others are more related to root hair formation/function and include proteins involved in nutrient uptake (transporters) or vesicular trafficking (cytoskeleton and RAB proteins). Interestingly, some of these proteins appear to be specifically expressed in root hairs and constitute very good candidates for further studies to elucidate unique features of this single cell model.

  17. Understanding the Residential Wood Heater Rules

    Science.gov (United States)

    Information on the components of the current wood heater new source performance standards (NSPS) and proposed updates to the NSPS including which types of heaters are covered under the rules and the benefits.

  18. Wood's lamp examination

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/003386.htm Wood lamp examination To use the sharing features on this page, please enable JavaScript. A Wood lamp examination is a test that uses ultraviolet ( ...

  19. Wood's lamp illumination (image)

    Science.gov (United States)

    A Wood's lamp emits ultraviolet light and can be a diagnostic aid in determining if someone has a fungal ... is an infection on the area where the Wood's lamp is illuminating, the area will fluoresce. Normally ...

  20. Wood-plastic combination

    International Nuclear Information System (INIS)

    Schaudy, R.

    1978-02-01

    A review on wood-plastic combinations is given including the production (wood and plastic component, radiation hardening, curing), the obtained properties, present applications and prospects for the future of these materials. (author)

  1. Mechanics of Wood Machining

    CERN Document Server

    Csanády, Etele

    2013-01-01

    Wood is one of the most valuable materials for mankind, and since our earliest days wood materials have been widely used. Today we have modern woodworking machine and tools; however, the raw wood materials available are continuously declining. Therefore we are forced to use this precious material more economically, reducing waste wherever possible. This new textbook on the “Mechanics of Wood Machining” combines the quantitative, mathematical analysis of the mechanisms of wood processing with practical recommendations and solutions. Bringing together materials from many sources, the book contains new theoretical and experimental approaches and offers a clear and systematic overview of the theory of wood cutting, thermal loading in wood-cutting tools, dynamic behaviour of tool and work piece, optimum choice of operational parameters and energy consumption, the wear process of the tools, and the general regularities of wood surface roughness. Diagrams are provided for the quick estimation of various process ...

  2. Empagliflozin/linagliptin single-pill combination therapy for patients with type 2 diabetes mellitus.

    Science.gov (United States)

    Jain, Rajeev Kumar

    2017-04-01

    Type 2 diabetes mellitus (T2DM) is typically progressive, with sequential addition of therapies often needed to address increasing hyperglycemia over the disease course. Using treatments in combination may be preferred to sequential addition, as a means of providing a more rapid clinical response and potentially avoiding clinical inertia. In such cases, a single-pill combination can help to reduce pill burden. Although various single-pill combinations of oral glucose-lowering agents are available, empagliflozin/linagliptin was the first approved combination of a sodium glucose co-transporter 2 (SGLT2) inhibitor with a dipeptidyl peptidase 4 (DPP-4) inhibitor in the United States. Areas covered: Two publications of the clinical trial investigating the efficacy and safety of single-pill combinations of empagliflozin/linagliptin in treatment-naive or metformin-treated patients with T2DM (NCT01422876) are reviewed, and their potential impact on clinical practice is discussed. Expert opinion: The study discussed provides evidence for the efficacy and safety of empagliflozin/linagliptin single pills. Addition of an empagliflozin/linagliptin single pill may be considered in patients with inadequate glycemic control on metformin, or as an alternative to first-line treatment with empagliflozin or linagliptin when metformin is not suitable, particularly in patients with very poor glycemic control, or those who need to achieve target more quickly.

  3. submitter Search for singly produced vector-like down-type quarks in single-lepton final states with ATLAS

    CERN Document Server

    Rehnisch, Laura

    A search for vector-like and excited down-type (Q = 1/3) quarks with the ATLAS detector is presented in this thesis. The existence of these quarks is predicted by various models beyond the Standard Model, motivated by some limitations of that theory. Quarks from two specific models are searched for in single production mode, as this is predicted to yield higher cross-sections than pair production in the investigated mass range. The search focuses on decays of the heavy quarks to a W boson and a top quark, the latter of which subsequently decays almost exclusively into another W boson and a bottom quark. Requiring one of the two W bosons to decay leptonically leads to final states containing exactly one lepton (electron or muon in this case), several jets, one of which can be identified as originating from a bottom quark, and some amount of missing energy in the transverse plane stemming from the neutrino of the leptonic W decay. The reconstructed mass of the heavy quark is used to discriminate between signal ...

  4. Non_standard Wood

    DEFF Research Database (Denmark)

    Tamke, Martin

    . Using parametric design tools and computer controlled production facilities Copenhagens Centre for IT and Architecture undertook a practice based research into performance based non-standard element design and mass customization techniques. In close cooperation with wood construction software......, but the integration of traditional wood craft techniques. The extensive use of self adjusting, load bearing wood-wood joints contributed to ease in production and assembly of a performance based architecture....

  5. Association between ABO blood type and live-birth outcomes in single-embryo transfer cycles.

    Science.gov (United States)

    Pereira, Nigel; Patel, Hency H; Stone, Logan D; Christos, Paul J; Elias, Rony T; Spandorfer, Steven D; Rosenwaks, Zev

    2017-11-01

    To investigate the association between ABO blood type and live-birth outcomes in patients undergoing IVF with day 5 single-embryo transfer (SET). Retrospective cohort study. University-affiliated center. Normal responders, blood type and live birth, while controlling for confounders. Odds ratios (OR) with 95% confidence intervals (CI) for live birth were estimated. A total of 2,329 patients were included. The mean age of the study cohort was 34.6 ± 4.78 years. The distribution of blood types was as follows: A = 897 (38.5%); B = 397 (17.0%); AB = 120 (5.2%); and, O = 1,915 (39.3%) patients. There was no difference in the baseline demographics, ovarian stimulation, or embryo quality parameters between the blood types. The unadjusted ORs for live birth when comparing blood type A (referent) with blood types B, AB, and O were 0.96 (95% CI, 0.6-1.7), 0.72 (95% CI, 0.4-1.2), and 0.96 (95% CI. 0.6-1.7), respectively. The adjusted ORs for live birth remained not significant when comparing blood type A to blood types B, AB, and O individually. No difference in birth weight or gestational age at delivery was noted among the four blood types. Our findings suggest that ABO blood type is not associated with live-birth rate, birth weight, or gestational age at delivery in patients undergoing IVF with day 5 SET. Copyright © 2017 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

  6. Iron Stain on Wood

    Science.gov (United States)

    Mark Knaebe

    2013-01-01

    Iron stain, an unsightly blue–black or gray discoloration, can occur on nearly all woods. Oak, redwood, cypress, and cedar are particularly prone to iron stain because these woods contain large amounts of tannin-like extractives. The discoloration is caused by a chemical reaction between extractives in the wood and iron in steel products, such as nails, screws, and...

  7. Wood preservative testing

    Science.gov (United States)

    Rebecca Ibach; Stan T. Lebow

    2012-01-01

    Most wood species used in commercial and residential construction have little natural biological durability and will suffer from biodeterioration when exposed to moisture. Historically, this problem has been overcome by treating wood for outdoor use with toxic wood preservatives. As societal acceptance of chemical use changes, there is continual pressure to develop and...

  8. Wood thermoplastic composites

    Science.gov (United States)

    Daniel F. Caulfield; Craig Clemons; Roger M. Rowell

    2010-01-01

    The wood industry can expand into new sustainable markets with the formation of a new class of composites with the marriage of the wood industry and the plastics industry. The wood component, usually a flour or fiber, is combined with a thermoplastic to form an extrudable, injectable or thermoformable composite that can be used in many non-structural applications....

  9. Wood Formation in Trees

    Science.gov (United States)

    Melanie Mauriat; Gregoire Le Provost; Phillippe Rozenberg; Sylvain Delzon; Nathalie Breda; Bruno Clair; Catherine Coutand; Jean-Christoph Domec; Thierry Fourcaud; Jacqueline Grima-Pettenati; Raul Herrera; Jean-Charles Leple; Nicolas Richet; Jean-Francois Trontin; Christophe Plomion

    2014-01-01

    Among the ecosystem services provided by forests, wood provisioning takes a central position. Wood and derived products have played a critical role in the evolution of human kind and demand for raw material is increasing in a foreseeable future. Wood is used for energy production, construction and a wide variety of products for which different properties are required....

  10. Request for wood samples

    NARCIS (Netherlands)

    NN,

    1977-01-01

    In recent years the wood collection at the Rijksherbarium was greatly expanded following a renewed interest in wood anatomy as an aid for solving classification problems. Staff members of the Rijksherbarium added to the collection by taking interesting wood samples with them from their expeditions

  11. Economics of wood dust

    Energy Technology Data Exchange (ETDEWEB)

    Kaiser, J.A.

    1980-11-01

    This article reviews the economic effects of wood dust. The most important use of wood today is a fuel, and wood chips and shavings are sources of feedstock for boilers. Other uses include wood chips in the manufacture of particleboard, wood dust as bedding in riding stables and race tracks, as mulch for florists, and as an absorbent in the meat packing industry. The installation of dust collection systems is strongly urged as the consequences of inadequate collection include rapid machine wear, poor environmental conditions for workers, general interference with work, and its combustibility makes it a constant fire hazard.

  12. Floodplains and wood

    Science.gov (United States)

    Wohl, Ellen

    2013-08-01

    Interactions between floodplains and wood date to the Carboniferous, when stable, multithread channel deposits appear with the evolution of tree-like plants. Foundational geologic texts, such as Lyell's, 1830Principles of Geology, describe floodplain-wood interactions, yet modern technical literature describes floodplain-wood interactions in detail for only a very limited range of environments. This likely reflects more than a century of deforestation, flow regulation, and channel engineering, including instream wood removal, which has resulted in severe wood depletion in most of the world's river networks. Instream wood affects floodplain form and process by altering flow resistance, conveyance and channel-floodplain connectivity, and influencing lateral and vertical accretion of floodplains. Instream wood reflects floodplain form and process as the floodplain influences wood recruitment via bank erosion and overbank flow, and wood transport and storage via floodplain effects on stage-discharge relations and flow resistance. Examining turnover times for instream wood at the reach scale in the context of a wood budget, floodplain characteristics influence fluvial transport and dynamics (wood recruitment), valley geometry (wood transport and storage), and hydraulics and river biota (wood decay and breakage). Accumulations of wood that vary from in situ jams and beaver dams in small channels to transport jams and log rafts in very large rivers can create stable, multithread channels and floodplain wetlands. Floodplain-wood interactions are best understood for a subset of small to medium-sized rivers in the temperate zone. We know little about these interactions on very large rivers, or on rivers in the tropical or boreal regions. This review suggests that most, if not all, channels and floodplains within forested catchments in the temperate zone historically had much greater wood loads and consequently much more obvious and important influences from wood than do

  13. Chemical composition and speciation of particulate organic matter from modern residential small-scale wood combustion appliances.

    Science.gov (United States)

    Czech, Hendryk; Miersch, Toni; Orasche, Jürgen; Abbaszade, Gülcin; Sippula, Olli; Tissari, Jarkko; Michalke, Bernhard; Schnelle-Kreis, Jürgen; Streibel, Thorsten; Jokiniemi, Jorma; Zimmermann, Ralf

    2018-01-15

    Combustion technologies of small-scale wood combustion appliances are continuously developed decrease emissions of various pollutants and increase energy conversion. One strategy to reduce emissions is the implementation of air staging technology in secondary air supply, which became an established technique for modern wood combustion appliances. On that account, emissions from a modern masonry heater fuelled with three types of common logwood (beech, birch and spruce) and a modern pellet boiler fuelled with commercial softwood pellets were investigated, which refer to representative combustion appliances in northern Europe In particular, emphasis was put on the organic constituents of PM2.5, including polycyclic aromatic hydrocarbons (PAHs), oxygenated PAHs (OPAHs) and phenolic species, by targeted and non-targeted mass spectrometric analysis techniques. Compared to conventional wood stoves and pellet boilers, organic emissions from the modern appliances were reduced by at least one order of magnitude, but to a different extent for single species. Hence, characteristic ratios of emission constituents and emission profiles for wood combustion identification and speciation do not hold for this type of advanced combustion technology. Additionally, an overall substantial reduction of typical wood combustion markers, such as phenolic species and anhydrous sugars, were observed. Finally, it was found that slow ignition of log woods changes the distribution of characteristic resin acids and phytosterols as well as their thermal alteration products, which are used as markers for specific wood types. Our results should be considered for wood combustion identification in positive matrix factorisation or chemical mass balance in northern Europe. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Synthesis and characterization of p-type boron-doped IIb diamond large single crystals

    International Nuclear Information System (INIS)

    Li Shang-Sheng; Li Xiao-Lei; Su Tai-Chao; Jia Xiao-Peng; Ma Hong-An; Huang Guo-Feng; Li Yong

    2011-01-01

    High-quality p-type boron-doped IIb diamond large single crystals are successfully synthesized by the temperature gradient method in a china-type cubic anvil high-pressure apparatus at about 5.5 GPa and 1600 K. The morphologies and surface textures of the synthetic diamond crystals with different boron additive quantities are characterized by using an optical microscope and a scanning electron microscope respectively. The impurities of nitrogen and boron in diamonds are detected by micro Fourier transform infrared technique. The electrical properties including resistivities, Hall coefficients, Hall mobilities and carrier densities of the synthesized samples are measured by a four-point probe and the Hall effect method. The results show that large p-type boron-doped diamond single crystals with few nitrogen impurities have been synthesized. With the increase of quantity of additive boron, some high-index crystal faces such as {113} gradually disappear, and some stripes and triangle pits occur on the crystal surface. This work is helpful for the further research and application of boron-doped semiconductor diamond. (cross-disciplinary physics and related areas of science and technology)

  15. Identification of PCR-base markers linked to wood splitting in Eucalyptus Grandis

    CSIR Research Space (South Africa)

    Barros, E

    2002-07-01

    Full Text Available Wood splitting is a defect in eucalyptus which results in considerable losses when converting logs to solid wood products. Commonly in forestry, molecular markers are identified through studying pedigrees from a single cross. This limits...

  16. Wood frame systems for wood homes

    Directory of Open Access Journals (Sweden)

    Julio Cesar Molina

    2010-12-01

    Full Text Available The use of constructive systems that combine strength, speed, with competitive differential techniques and mainly, compromising with the environment, is becoming more popular in Brazil. The constructive system in wood frame for houses of up to five stories is very interesting, because it is a light system, structured in reforested treated wood which allows the combination of several materials, besides allowing speed in the construction and total control of the expenses already in the project phase for being industrialized. The structural behavior of the wood frame is superior to the structural masonry in strength, thermal and acoustic comfort. However, in Brazil, the wood frame is still little known and used, due to lack of technical knowledge about the system, prejudice associated the bad use of the wood as construction material, or still, in some cases, lack of normalization. The aim of this manuscript consists of presenting the main technical characteristics and advantages of the constructive system in wood frame homes, approaching the main stages of the constructive process through examples, showing the materials used in the construction, in addition the main international normative recommendations of the project. Thus, this manuscript also hopes to contribute to the popularization of the wood frame system in Brazil, since it is a competitive, fast and ecologically correct system. Moreover, nowadays, an enormous effort of the technical, commercial and industrial section has been accomplished for the development of this system in the country.

  17. Single-pill combination therapy for type 2 diabetes mellitus: linagliptin plus empagliflozin.

    Science.gov (United States)

    Aronson, Ronnie

    2015-05-01

    Treatment of type 2 diabetes mellitus invariably requires the use of multiple daily medications which can impact negatively on patient adherence. As a result, there is growing interest in the use of single-pill combinations that can reduce the pill burden. Many such formulations incorporate metformin, although this agent is not suitable for all patients. The single-pill combination of the dipeptidyl peptidase-4 inhibitor linagliptin with the sodium glucose co-transporter 2 inhibitor empagliflozin offers a new and attractive option, given their complementary mechanisms of action. Publications with titles containing the keywords 'linagliptin' or 'empagliflozin' were identified from a non-systematic search of PubMed without date restrictions, together with abstracts presented at the annual meetings of the American Diabetes Association and the European Association for the Study of Diabetes 2012-2014. ClinicalTrials.gov was searched for entries containing these two keywords. Additional references known to the author were included. The efficacy and safety of linagliptin and empagliflozin as monotherapy or in combination with other oral antidiabetic drugs has been established through extensive clinical trial programs. Studies specifically evaluating the efficacy/safety of a dipeptidyl peptidase-4 inhibitor/sodium glucose co-transporter 2 inhibitor in combination are limited, but do include two studies of linagliptin/empagliflozin of up to 52 weeks in duration. These studies show that the single-pill combination of linagliptin and empagliflozin produced clinical improvements in glycemic control that were generally superior to the improvements seen with linagliptin and empagliflozin alone, but with a safety profile comparable to that of the individual constituents. The single-pill combination of linagliptin and empagliflozin, with their complementary mechanisms of action, is a promising treatment option for patients with type 2 diabetes mellitus. It would reduce the daily

  18. The making of a market. Supply- and demand-side perspectives on institutional innovation in Sweden's wood fuel use

    International Nuclear Information System (INIS)

    2001-01-01

    This thesis documents and analyses the rapidly increasing wood fuel use in Sweden in five separate studies of prominent actors in the making of the wood fuel market. These studies report government policy, forest owners' incentives, and district heating companies' experiences. The development of wood fuel use is examined as a story of technological and institutional change initially prompted by government policy. The change has involved dedicated action among all of the actors, with the Swedish government initiating new policies, legislation, and information activities, with district heating companies investing in new technology and trading, and with forest owners making new decisions on forest management practices. Institutional change in the wood fuel sector, in other words, is the result of innovation on the part of the actors involved. The papers included in the study identify and analyse concerns of the actors involved in making the wood fuel market. Within the district heating sector, transaction costs, as measured by problems to trade perceived by managements, have decreased with learning. Transformation costs, due to technical problems, are not perceived to have followed this trend. Technical investments in heat production have a long technical life time and demand large investment costs. This in turn means long planning and decision periods. Investments are made for a number of company-specific reasons, perhaps most importantly simply to increase heat and/or electricity generation capacity. Policy instruments may tip a decision in favor of wood fuels, but they could not be the single parameter determining company investments. Two kinds of forest owners selling wood fuels were identified, a forest manager type who acts more on his/her own initiative, and another kind, who relies more on the advice of the traditional timber buyer. Forest owners selling wood fuels contemplating whether to sell wood fuels or not are strongly influenced by soil fertility

  19. Wood production, wood technology, and biotechnological impacts.

    OpenAIRE

    2007-01-01

    In the year 2001, Prof. Dr. Ursula Kües was appointed at the Faculty of Forest Sciences and Forest Ecology of the Georg-August-University Göttingen to the chair Molecular Wood Biotechnology endowed by the Deutsche Bundesstiftung Umwelt (DBU). Her group studies higher fungi in basic and applied research. Research foci are on mushroom development and on fungal enzymes degrading wood and their applications in wood biotechnology. This book has been edited to thank the DBU for all support given to...

  20. Single-channel L-type Ca2+ currents in chicken embryo semicircular canal type I and type II hair cells.

    Science.gov (United States)

    Zampini, Valeria; Valli, Paolo; Zucca, Giampiero; Masetto, Sergio

    2006-08-01

    Few data are available concerning single Ca channel properties in inner ear hair cells and particularly none in vestibular type I hair cells. By using the cell-attached configuration of the patch-clamp technique in combination with the semicircular canal crista slice preparation, we determined the elementary properties of voltage-dependent Ca channels in chicken embryo type I and type II hair cells. The pipette solutions included Bay K 8644. With 70 mM Ba(2+) in the patch pipette, Ca channel activity appeared as very brief openings at -60 mV. Ca channel properties were found to be similar in type I and type II hair cells; therefore data were pooled. The mean inward current amplitude was -1.3 +/- 0.1 (SD) pA at - 30 mV (n = 16). The average slope conductance was 21 pS (n = 20). With 5 mM Ba(2+) in the patch pipette, very brief openings were already detectable at -80 mV. The mean inward current amplitude was -0.7 +/- 0.2 pA at -40 mV (n = 9). The average slope conductance was 11 pS (n = 9). The mean open time and the open probability increased significantly with depolarization. Ca channel activity was still present and unaffected when omega-agatoxin IVA (2 microM) and omega-conotoxin GVIA (3.2 microM) were added to the pipette solution. Our results show that types I and II hair cells express L-type Ca channels with similar properties. Moreover, they suggest that in vivo Ca(2+) influx might occur at membrane voltages more negative than -60 mV.

  1. A new type of single-phase five-level inverter

    Science.gov (United States)

    Xu, Zhi; Li, Shengnan; Qin, Risheng; Zhao, Yanhang

    2017-11-01

    At present, Neutral Point Clamped (NPC) multilevel inverter is widely applied in new energy field. However, it has some disadvantages including low utilization rate of direct current (DC) voltage source and the unbalance of neutral potential. Therefore, a new single-phase five level inverter is proposed in this paper. It has two stage structure, the former stage is equivalent to three level DC/DC converter, and the back stage uses H bridge to realize inverter. Compared with the original central clamp type inverter, the new five level inverter can improve the utilization of DC voltage, and realize the neutral point potential balance with hysteresis comparator.

  2. Evaluation of bolted connections in wood-plastic composites

    Science.gov (United States)

    Arnandha, Yudhi; Satyarno, Iman; Awaludin, Ali; Irawati, Inggar Septia; Ihsan, Muhamad; Wijanarko, Felyx Biondy; William, Mahdinur, Fardhani, Arfiati

    2017-03-01

    Wood-plastic composite (WPC) is a relatively new material that consists of sawdust and plastic polymer using the extrusion process. Due to its attributes such as low water content, low maintenance, UV durability and being fungi and termite resistant. Nowadays, WPC has already been produced in Indonesia using sawdust from local wood such as Albizia (Paraserianthes falcataria) and Teak (Tectona grandis). Moreover preliminary studies about the physical and mechanical WPC board from Albizia sawdust and HDPE plastic have been carried out. Based on these studies, WPC has a high shear strength around 25-30 MPa higher than its original wood shear strength. This paper was a part of the research in evaluating WPC as potential sheathing in a shear wall system. Since still little is known about connection behavior in WPC using Indonesian local wood, this study evaluated the connection for both of these two types of wood-plastic composite. WPC board from Albizia sawdust will be projected as shear wall sheathing and WPC stud from Teak sawdust projected to be shear wall frame. For this study, the embedding strength for both WPC was determined according to ASTM D 5764 standard, using two types of bolts (stainless bolt and standard bolt) with several diameters as variation (6 mm, 8 mm, 10 and 12 mm). Hence, dowel-bearing test under fastened condition conducted accordance to ASTM D5652, hereby the yield strength then compared with the prediction yield strength from European Yield Model (EYM). According to both single and double shear connection, it can be concluded that yield strength from the EYM method tended to under-predict the 5% diameter offset yield than the actual yield strength from the test. The yield strength itself increase with the increase of bolt diameter. For single shear connection, the highest yield strength was 12 mm standard bolt around 9732 N, slightly higher than stainless bolt around 9393 N. Whereby for double shear connection, the highest yield strength was

  3. High speed single nucleotide polymorphism typing of a hereditary haemochromatosis mutation with capillary array electrophoresis microplates.

    Science.gov (United States)

    Medintz, I; Wong, W W; Sensabaugh, G; Mathies, R A

    2000-07-01

    A single nucleotide polymorphism (SNP) typing assay is developed and evaluated on a microfabricated capillary array electrophoresis system. Using fluorescently labeled allele-specific primers, the S65C (193A-->T) substitution associated with hereditary haemochromatosis in the HFE gene is genotyped. The covalently labeled polymerase chain reaction (PCR) products are separated on a microfabricated radial capillary array electrophoresis microplate using nondenaturing gel media in under two minutes. Detection is accomplished with a laser-excited rotary confocal scanner. The Rox-labeled A-allele specific amplicon (211 bp) is differentiated from the R110-labeled T-allele specific amplicon (201 bp) by both size and color. This study demonstrates the feasibility of using allele-specific PCR with covalently labeled primers for high speed fluorescent SNP typing on microfabricated radial capillary array electrophoresis microplates.

  4. Characterization and potential recycling of home building wood waste

    Science.gov (United States)

    Philip A. Araman; D.P. Hindman; M.F. Winn

    2010-01-01

    Construction waste represents a significant portion of landfill waste, estimated as 17% of the total waste stream. Wood construction waste of a 2000 square foot single family home we found to be 1500-3700 lbs of solid-sawn wood, and 1000-1800 lbs of engineered wood products (EWP). Much of the solid-sawn lumber and EWPs could be recycled into several products. Through a...

  5. Laser microdissection and DNA typing of cells from single hair follicles.

    Science.gov (United States)

    Di Martino, D; Giuffrè, G; Staiti, N; Simone, A; Todaro, P; Saravo, L

    2004-12-02

    Isolation and identification of single cells from tissue samples or smears assume a great relevance in pathological and forensic applications; in this latter field, the possibility to identify a specific genetic profile can be obtained by short tandem repeat (STR) typing, allowing to achieve a scientific proof important in law courts. It is well known that DNA extraction may be performed from several tissue fragments, blood traces, spermatozoa as well as telogen hair. However, in the last case, few follicle cells are coupled to a great amount of keratin reducing the efficiency of DNA amplification. Recently, the introduction of laser microdissection technique has greatly improved the capability to select single cells without any cross-contamination. In the present report, we have performed a laser microdissection using a Leica AS LMD (Leica Microsystems, Germany), utilized on cutting the telogen hair in order to exclusively collect the lower part of the follicle and reduce keratin contamination. In this way we can accurately extract an adequate amount of DNA, successfully typed by STR profile.

  6. Radiation processed composite materials of wood and elastic polyester resins

    International Nuclear Information System (INIS)

    Tapolcai, I.; Czvikovszky, T.

    1983-01-01

    The radiation polymerization of multifunctional unsaturated polyester-monomer mixtures in wood forms interpenetrating network system. The mechanical resistance (compression, abrasion, hardness, etc.) of these composite materials are generally well over the original wood, however the impact strength is almost the same or even reduced, in comparison to the wood itself. An attempt is made using elastic polyester resins to produced wood-polyester composite materials with improved modulus of elasticity and impact properties. For the impregnation of European beech wood two types of elastic unsaturated polyester resins were used. The exothermic effect of radiation copolymerization of these resins in wood has been measured and the dose rate effects as well as hardening dose was determined. Felxural strength and impact properties were examined. Elastic unsaturated polyester resins improved the impact strength of wood composite materials. (author)

  7. Urban Wood Waste Resource Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Wiltsee, G.

    1998-11-20

    This study collected and analyzed data on urban wood waste resources in 30 randomly selected metropolitan areas in the United States. Three major categories wood wastes disposed with, or recovered from, the municipal solid waste stream; industrial wood wastes such as wood scraps and sawdust from pallet recycling, woodworking shops, and lumberyards; and wood in construction/demolition and land clearing debris.

  8. Distinct circular single-stranded DNA viruses exist in different soil types.

    Science.gov (United States)

    Reavy, Brian; Swanson, Maud M; Cock, Peter J A; Dawson, Lorna; Freitag, Thomas E; Singh, Brajesh K; Torrance, Lesley; Mushegian, Arcady R; Taliansky, Michael

    2015-06-15

    The potential dependence of virus populations on soil types was examined by electron microscopy, and the total abundance of virus particles in four soil types was similar to that previously observed in soil samples. The four soil types examined differed in the relative abundances of four morphological groups of viruses. Machair, a unique type of coastal soil in western Scotland and Ireland, differed from the others tested in having a higher proportion of tailed bacteriophages. The other soils examined contained predominantly spherical and thin filamentous virus particles, but the Machair soil had a more even distribution of the virus types. As the first step in looking at differences in populations in detail, virus sequences from Machair and brown earth (agricultural pasture) soils were examined by metagenomic sequencing after enriching for circular Rep-encoding single-stranded DNA (ssDNA) (CRESS-DNA) virus genomes. Sequences from the family Microviridae (icosahedral viruses mainly infecting bacteria) of CRESS-DNA viruses were predominant in both soils. Phylogenetic analysis of Microviridae major coat protein sequences from the Machair viruses showed that they spanned most of the diversity of the subfamily Gokushovirinae, whose members mainly infect obligate intracellular parasites. The brown earth soil had a higher proportion of sequences that matched the morphologically similar family Circoviridae in BLAST searches. However, analysis of putative replicase proteins that were similar to those of viruses in the Circoviridae showed that they are a novel clade of Circoviridae-related CRESS-DNA viruses distinct from known Circoviridae genera. Different soils have substantially different taxonomic biodiversities even within ssDNA viruses, which may be driven by physicochemical factors. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

  9. THE DISTRIBUTION OF DIFFERENT TYPES OF DIABETES IN CHILDHOOD: A SINGLE CENTER EXPERIENCE.

    Science.gov (United States)

    Haliloğlu, Belma; Abali, Saygın; Buğrul, Fuat; Çelik, Enes; Baş, Serpil; Atay, Zeynep; Güran, Tülay; Turan, Serap; Bereket, Abdullah

    2017-11-24

    Type 1 diabetes (T1D) is the most common cause of diabetes in childhood but type 2 diabetes (T2D) and maturity onset diabetes of the young (MODY) are emerging and noteworthy causes of diabetes in youths. The aim of the study is to determine the distribution, trends and clinical features of the different types of diabetes in childhood in a tertiary single-center. Children and adolescents aged 0-18 years who were diagnosed "diabetes/persistent hyperglycemia" between January 1999 and December 2016, were reviewed. Clinical and laboratory characteristics of the patients at the diagnosis and type of diabetes were recorded. The mean age of 835 patients (48.7% females) at diagnosis was 8.8±4.4 years. Eighty-four percent of the patients were diagnosed with T1D, 5.7% with T2D, 5.3% with clinical MODY and 5% with other types of diabetes. The frequency of all DKA and severe DKA in T1D were 48.4% and 11.6%, respectively. Fourteen patients (29.2%) with T2D presented with ketosis and 2 of them (4.2%) had DKA at diagnosis. Antibody positivity was 83.1% in T1D and 14.8% in T2D. A statistically significant increase in the frequency of T2D has clearly been demonstrated in recent years with a frequency of 1.9%, 2.4% and 7.9% in 1999-2004, 2005-2010 and 2011-2016, respectively (pchildhood, a trend towards increase in the frequency of T2D in recent years is notable in our population.

  10. Feasibility study for new ecolabels according to ISO 14024 (type 1) within the product group: wood pellet heating systems; Machbarkeitsstudie fuer neue Umweltzeichen fuer die Produktgruppe: Holzpelletfeuerungen

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmann, E.; Weiss, J.; Hirschl, B. [Institut fuer Oekologische Wirtschaftsforschung (IOEW) gGmbH, Berlin (Germany)

    2003-01-01

    This assessment is a feasibility study according to ISO 14024. It deals with the question whether an ecolabel is suitable for wood pellet heating systems and how concrete criteria for an ecolabel for wood pellet heating plants could be specified. The study begins with a comprehensive market analysis in order to identify possible plants for which an ecolabel would make sense. In the main part of the study, the environmental relevance of the chosen plants is analysed. For this analysis, plant manufacturers were interviewed and a comparison between wood pellet heating systems and heating systems which use gas, oil or wood was carried out. On the basis of this analysis, it was possible to derive a number of criteria which were discussed with company representatives and other experts in this field. As a result of this dialogue and the investigation process as a whole, the introduction of an ecolabel for wood pellet heating plants can be recommended. Wood pellet heating systems are characterized by their high level of automatation and the use of standardized fuels with constant high quality. Thus, they reach high combustion quality with low emission rates, and risks of misuse are minimized. They may contribute to the increased use of renewable energies and thereby to the achievement of climate protection goals. The proposed certification principles comprise requirements regarding (a) the efficient energy use (efficiency factor under partial load and nominal load, plant's supplementary energy consumption), (b) emission values for CO, NO{sub x}, dust and organic substances, (c) the offer of additional services, as well as (d) requirements with regard to the operating instructions. The transcription of the label is proposed as 'Ecolabel.. because low emission and energy-efficient'. (orig.) [German] Beim vorliegenden Gutachten handelt es sich um eine Machbarkeitsstudie nach ISO 14024. Es behandelt die Frage, ob ein Umweltzeichen fuer Holzpelletfeuerungen

  11. Chapter 9: Wood Energy

    Science.gov (United States)

    Francisco X. Aguilar; Karen Abt; Branko Glavonjic; Eugene Lopatin; Warren  Mabee

    2016-01-01

    The availabilty of information on wood energy continues to improve, particularly for commoditized woodfuels.  Wood energy consumption and production vary in the UNECE region because demand is strngly affected by weather and the prices of competing energy sources.  There has been an increase in wood energy in the power-and-heat sector in the EU28 and North American...

  12. Complex geometries in wood

    DEFF Research Database (Denmark)

    Tamke, Martin; Ramsgaard Thomsen, Mette; Riiber Nielsen, Jacob

    2009-01-01

    The versatility of wood constructions and traditional wood joints for the production of non standard elements was in focus of a design based research. Herein we established a seamless process from digital design to fabrication. A first research phase centered on the development of a robust...... parametric model and a generic design language a later explored the possibilities to construct complex shaped geometries with self registering joints on modern wood crafting machines. The research was carried out as collaboration with industrial partners....

  13. Complex geometries in wood

    DEFF Research Database (Denmark)

    Tamke, Martin; Ramsgaard Thomsen, Mette; Riiber Nielsen, Jacob

    2009-01-01

    The versatility of wood constructions and traditional wood joints for the production of non standard elements was in focus of a design based research. Herein we established a seamless process from digital design to fabrication. A first research phase centered on the development of a robust parame...... parametric model and a generic design language a later explored the possibilities to construct complex shaped geometries with self registering joints on modern wood crafting machines. The research was carried out as collaboration with industrial partners....

  14. Wood pellet seminar

    International Nuclear Information System (INIS)

    Aarniala, M.; Puhakka, A.

    2001-01-01

    The objective of the wood pellet seminar, arranged by OPET Finland and North Karelia Polytechnic, was to deliver information on wood pellets, pellet burners and boilers, heating systems and building, as well as on the activities of wood energy advisors. The first day of the seminar consisted of presentations of equipment and products, and of advisory desks for builders. The second day of the seminar consisted of presentations held by wood pellet experts. Pellet markets, the economy and production, the development of the pellet markets and their problems (in Austria), the economy of heating of real estates by different fuel alternatives, the production, delivery and marketing of wood pellets, the utilization of wood pellet in different utilization sites, the use of wood pellets in detached houses, pellet burners and fireplaces, and conversion of communal real estate houses to use wood pellets were discussed in the presentations. The presentations held in the third day discussed the utilization of wood pellets in power plants, the regional promotion of the production and the use of pellets. The seminar consisted also of visits to pellet manufacturing plant and two pellet burning heating plants

  15. Moisture Transport in Wood

    DEFF Research Database (Denmark)

    Astrup, Thomas; Hansen, Kurt Kielsgaard; Hoffmeyer, Preben

    2005-01-01

    Modelling of moisture transport in wood is of great importance as most mechanical and physical properties of wood depend on moisture content. Moisture transport in porous materials is often described by Ficks second law, but several observations indicate that this does not apply very well to wood....... Recently at the Technical University of Denmark, Department of Civil Engineering, a new model for moisture transport in wood has been developed. The model divides the transport into two phases, namely water vapour in the cell lumens and bound water in the cell walls....

  16. Plasminogen Activator Inhibitor Type-1 Tag Single-Nucleotide Polymorphisms in Patients with Diabetes Mellitus Type 2 and Diabetic Retinopathy.

    Science.gov (United States)

    Siokas, Vasileios; Dardiotis, Efthimios; Sokolakis, Thomas; Kotoula, Maria; Tachmitzi, Sophia V; Chatzoulis, Dimitrios Z; Almpanidou, Pavlina; Stefanidis, Ioannis; Hadjigeorgiou, Georgios M; Tsironi, Evangelia E

    2017-07-01

    There is accumulating evidence for genetic susceptibility to the development of diabetic retinopathy (DR). The role of plasminogen activator inhibitor-1 (PAI-1) in DR risk remains controversial. The present study was designed to investigate possible influence of PAI-1 gene region polymorphisms on the risk of DR and on the risk of developing DR early vs late in the course of type 2 diabetes mellitus (T2DM). A total of 138 patients with DR, 107 patients with T2DM without DR, and 315 healthy controls were recruited. To cover the majority of the genetic variability across the extended region of PAI-1 gene, five tag single-nucleotide polymorphisms (SNPs) from the HapMap using a pairwise approach and an r 2 ≥ 0.8 and a minor allele frequency (MAF) of >0.05 were identified. Using logistic regression analyses, tag SNPs and haplotypes were tested for associations with DR risk and risk of DR development early or late in the course of T2DM. The generalized odds ratio (OR G ) was calculated to estimate the mutational load effect on DR development among all participants. Corrections for multiple comparisons were carried out (p-value < 0.01). A significant effect of rs2070682 on the risk of early DR onset was found in the codominant model of inheritance [odds ratio, OR (95% confidence interval, CI): 5.04 (1.47-17.28), p = 0.018]. However, this association marginally did not survive multiple testing corrections. No other significant association between PAI-1 tag-SNPs and haplotypes was revealed. Furthermore, no significant mutational load effect of PAI-1 tag SNPs on the risk of DR development in T2DM course was found. In conclusion, the present study does not provide any strong evidence that PAI-1 gene variants are implicated in the risk of DR or the development of DR during T2DM course.

  17. Emission factors of particulate matter, polycyclic aromatic hydrocarbons, and levoglucosan from wood combustion in south-central Chile.

    Science.gov (United States)

    Jimenez, Jorge; Farias, Oscar; Quiroz, Roberto; Yañez, Jorge

    2017-07-01

    In south-central Chile, wood stoves have been identified as an important source of air pollution in populated areas. Eucalyptus (Eucalyptus globulus), Chilean oak (Nothofagus oblique), and mimosa (Acacia dealbata) were burned in a single-chamber slow-combustion wood stove at a controlled testing facility located at the University of Concepción, Chile. In each experiment, 2.7-3.1 kg of firewood were combusted while continuously monitoring temperature, exhaust gases, burn rate, and collecting particulate matter samples in Teflon filters under isokinetic conditions for polycyclic aromatic hydrocarbon and levoglucosan analyses. Mean particulate matter emission factors were 2.03, 4.06, and 3.84 g/kg dry wood for eucalyptus, oak, and mimosa, respectively. The emission factors were inversely correlated with combustion efficiency. The mean emission factors of the sums of 12 polycyclic aromatic hydrocarbons in particle phases were 1472.5, 2134.0, and 747.5 μg/kg for eucalyptus, oak, and mimosa, respectively. Fluoranthene, pyrene, benzo[a]anthracene, and chrysene were present in the particle phase in higher proportions compared with other polycyclic aromatic hydrocarbons that were analyzed. Mean levoglucosan emission factors were 854.9, 202.3, and 328.0 mg/kg for eucalyptus, oak, and mimosa, respectively. Since the emissions of particulate matter and other pollutants were inversely correlated with combustion efficiency, implementing more efficient technologies would help to reduce air pollutant emissions from wood combustion. Residential wood burning has been identified as a significant source of air pollution in populated areas. Local wood species are combusted for home cooking and heating, which releases several toxic air pollutants, including particulate matter, carbon monoxide, and polycyclic aromatic hydrocarbons. Air pollutant emissions depend on the type of wood and the technology and operational conditions of the wood stove. A better understanding of emissions from

  18. Study of the signal formation in single-type column 3D silicon detectors

    International Nuclear Information System (INIS)

    Piemonte, Claudio; Boscardin, Maurizio; Bosisio, Luciano; Dalla Betta, Gian-Franco; Pozza, Alberto; Ronchin, Sabina; Zorzi, Nicola

    2007-01-01

    Because of their superior radiation resistance, three-dimensional (3D) silicon sensors are receiving more and more interest for application in the innermost layers of tracker systems for experiments running in very high luminosity colliders. Their short electrode distance allows for both a low depletion voltage and a high charge collection efficiency even at extremely high radiation fluences. In order to fully understand the properties of a 3D detector, a thorough characterization of the signal formation mechanism is of paramount importance. In this work the shape of the current induced by localized and uniform charge depositions in a single-type column 3D detector is studied. A first row estimation is given applying the Ramo theorem, then a more complete TCAD simulation is used to provide a more realistic pulse shape

  19. High efficiency 40 K single-stage Stirling-type pulse tube cryocooler

    Science.gov (United States)

    Wu, X. L.; Chen, L. B.; Pan, C. Z.; Cui, C.; Wang, J. J.; Zhou, Y.

    2017-12-01

    A high efficiency single-stage Stirling-type coaxial pulse tube cryocooler (SPTC) operating at around 40 K has been designed, built and tested. The double-inlet and the inertance tubes together with the gas reservoir were adopted as the phase shifters. Under the conditions of 2.5 MPa charging pressure and 30 Hz operating frequency, the prototype has achieved a no-load temperature of 23.8 K with 330 W of electric input power at a rejection temperature of 279 K. When the input power increases to 400 W, it can achieve a cooling capacity of 4.7 W/40 K while rejecting heat at 279 K yielding an efficiency of 7.02% relative to Carnot. It achieves a cooling capacity of 5 W/40 K with an input power of 450 W. It takes 10 minutes for the SPTC to cool to its no-load temperature of 40 K from 295 K.

  20. Stochastic gravitational wave background from the single-degenerate channel of type Ia supernovae

    International Nuclear Information System (INIS)

    Falta, David; Fisher, Robert

    2011-01-01

    We demonstrate that the integrated gravitational wave signal of type Ia supernovae (SNe Ia) in the single-degenerate channel out to cosmological distances gives rise to a continuous background to spaceborne gravitational wave detectors, including the Big Bang Observer and Deci-Hertz Interferometer Gravitational wave Observatory planned missions. This gravitational wave background from SNe Ia acts as a noise background in the frequency range 0.1-10 Hz, which heretofore was thought to be relatively free from astrophysical sources apart from neutron-star and white-dwarf binaries, and therefore a key window in which to study primordial gravitational waves generated by inflation. While inflationary energy scales of > or approx. 10 16 GeV yield inflationary gravitational wave backgrounds in excess of our range of predicted backgrounds, for lower energy scales of ∼10 15 GeV, the inflationary gravitational wave background becomes comparable to the noise background from SNe Ia.

  1. The contribution of single photon emission computed tomography in the clinical assessment of Alzheimer type dementia

    International Nuclear Information System (INIS)

    Boudousq, V.; Collombier, L.; Kotzki, P.O.

    1999-01-01

    Interest of brain single-photon emission computed tomography to support clinical diagnosis of Alzheimer-type dementia is now established. Numerous studies have reported a decreased perfusion in the association cortex of the parietal lobe and the posterior temporal regions. In patients with mild cognitive complaints, the presence of focal hypoperfusion may increase substantially the probability of the disease. In addition, emission tomography emerges as a helpful tool in situation in which there is diagnostic doubt. In this case, the presence of temporo-parietal perfusion deficit associated with hippocampal atrophy on MRI or X-ray computed tomography contributes to diagnostic accuracy. However, some studies suggest that emission tomography may be useful for preclinical prediction of Alzheimer's disease and to predict cognitive decline. (author)

  2. Phonon-limited mobility in n-type single-layer MoS2 from first principles

    DEFF Research Database (Denmark)

    Kaasbjerg, Kristen; Thygesen, Kristian S.; Jacobsen, Karsten W.

    2012-01-01

    We study the phonon-limited mobility in intrinsic n-type single-layer MoS2 for temperatures T > 100 K. The materials properties including the electron-phonon interaction are calculated from first principles and the deformation potentials and Frohlich interaction in single-layer MoS2 are establish...

  3. Oscillations of a single Abrikosov vortex in hard type-II superconductors

    Science.gov (United States)

    Rusakov, V. F.; Chabanenko, V. V.; Nabiałek, A.; Chumak, O. M.

    2017-06-01

    During the last decade, detection and manipulation of single vortex lines in bulk superconductors have been achieved experimentally. Electrodynamic response of pinned vortices in the high-frequency range is instrumental in studying specific aspects of their behavior. The present paper reviews the state of the art in studies of the oscillations of a single Abrikosov vortex in type II superconductors. The equations for free and forced oscillations of a single elastic vortex line are analyzed taking into account different forces affecting its motion: pinning, elasticity, viscosity and the Lorenz force. The equations also account for the inertial properties of a vortex due to various mechanisms of massiveness. The nature and magnitude of the vortex effective mass caused by some of the mechanisms are discussed in the paper. The roles of each force and inertia in the free oscillation spectrum are thoroughly analyzed. For the De Gennes and Matricon mode (at about a megahertz) with parabolic dispersion and the pinning force taken into account, there is an activation threshold. Taking into account the effective vortex mass in the equation of motion leads to the occurrence of a high-frequency mode (at about a terahertz) in the oscillation spectrum which is also of the activation nature. Estimations of the characteristic frequencies for these modes are given for two common superconductors, NbTi and anisotropic YBaCuO. The paper also presents the features of the resonant behavior of an elastic massive vortex line arising under an external uniform harmonic driving force that decays into the bulk of the sample, taking into account all the above forces. The frequency and temperature dependences of the energy absorption by a vortex line are analyzed. Maximum absorption in the low-frequency mode corresponds to the threshold frequency, while that in the high-frequency mode corresponds to the vortex cyclotron frequency. Vortex manipulation experiments and vortex dynamics simulation

  4. The wood, renewable energy

    International Nuclear Information System (INIS)

    Acket, C.

    2006-12-01

    This document evaluates the french forest situation and its future. Indeed, the wood energy constitutes in France the first renewable energy after the hydraulic. It presents the today situation of the french forest providing statistical data, evaluation of the energy estimation, the carbon fixation, the resources, the perspectives wood energy for 2050, the biofuels and an economic analysis. (A.L.B.)

  5. Wood thermoplastic composites

    Science.gov (United States)

    Daniel F. Caulfield; Craig Clemons; Rodney E. Jacobson; Roger M. Rowell

    2005-01-01

    The term “wood-plastic composites” refers to any number of composites that contain wood (of any form) and either thermoset or thermoplastic polymers. Thermosets or thermoset polymers are plastics that, once cured, cannot be remelted by heating. These include cured resins, such as epoxies and phenolics, plastics with which the forest products industry is most familiar (...

  6. Wood supply and demand

    Science.gov (United States)

    Peter J. Ince; David B. McKeever

    2011-01-01

    At times in history, there have been concerns that demand for wood (timber) would be greater than the ability to supply it, but that concern has recently dissipated. The wood supply and demand situation has changed because of market transitions, economic downturns, and continued forest growth. This article provides a concise overview of this change as it relates to the...

  7. Heat sterilization of wood

    Science.gov (United States)

    Xiping Wang

    2010-01-01

    Two important questions should be considered in heat sterilizing solid wood materials: First, what temperature–time regime is required to kill a particular pest? Second, how much time is required to heat the center of any wood configuration to the kill temperature? The entomology research on the first question has facilitated the development of international standards...

  8. Material model for wood

    NARCIS (Netherlands)

    Sandhaas, C.; Van de Kuilen, J.W.G.

    2013-01-01

    Wood is highly anisotropic and shows ductile behaviour in compression and brittle behaviour in tension and shear where both failure modes can occur simultaneously. A 3D material model for wood based on the concepts of continuum damage mechanics was developed. A material subroutine containing the

  9. Economy of wood supply

    International Nuclear Information System (INIS)

    Imponen, V.

    1993-01-01

    Research and development of wood fuels production was vigorous in the beginning of the 1980's. Techniques and working methods used in combined harvesting and transportation of energy and merchantable wood were developed in addition to separate energy wood delivery. After a ten year silent period the research on this field was started again. At present the underutilization of forest supplies and the environmental effects of energy production based on fossil fuels caused the rebeginning of the research. One alternative for reduction of the price of wood fuels at the utilization site is the integration of energy and merchantable wood deliveries together. Hence the harvesting and transportation devices can be operated effectively, and the organizational costs are decreased as well. The wood delivery costs consist of the stumpage price, the harvesting and transportation costs, and of general expenses. The stumpage price form the largest cost category (over 50 %) of the industrial merchantable wood delivery, and the harvesting and transportation costs in the case of thinningwood delivery. Forest transportation is the largest part of the delivery costs of logging residues. The general expenses, consisting of the management costs and the interest costs of the capital bound to the storages, form a remarkable cost category in delivery of low-rank wood for energy or conversion purposes. The costs caused by the harvesting of thinningwood, the logging residues, chipping and crushing, the lorry transportation are reviewed in this presentation

  10. Wood energy and air quality

    International Nuclear Information System (INIS)

    2015-12-01

    This publication first recalls the main benefits of the use of wood, the first source of renewable energy in France: abundant and local resource, low CO 2 emission, competitiveness, job creation. It comments the relationship between the use of this source of energy and the compliance with air quality standards as they are notably defined by European directives, as the use of wood as heating source is one of the recommended lever to improve air quality. The publication comments emissions generated by this type of heating (mainly in the housing sector, with some critical meteorological periods). Levers for actions are discussed: fleet renewal to promote the best performing equipment, practice improvements (fuel quality, apparatus maintenance). Actions undertaken by the ADEME are briefly reviewed: support to individual equipment fleet modernisation, support to R and D, support to the sector, and information and communication

  11. Wood construction under cold climate

    DEFF Research Database (Denmark)

    Wang, Xiaodong; Hagman, Olle; Sundqvist, Bror

    2014-01-01

    was sensitive to temperature change. MUF, PRF and PVAc resins demonstrated different characters with Norway spruce and Scot pine. At room temperature, all types of adhesive showed relative stability, in terms of shear strength variation. While at low temperature, the shear strength varied considerably. More......) and Scots pine (Pinus sylvestris) joints (150mm x 20mm x 10mm) were bonded with seven commercially available resins (PUR, PVAc, EPI, MF, MUF1, PRF and MUF2) and tested at six temperatures (20, -20, -30, -40, -50 and -60 °C), respectively. Generally, for both species, temperature changes significantly...... affected shear strength of wood joints. As temperature decreased, the shear strength decreased. PUR resin resulted in the strongest shear strength at all temperatures tested. MF resin responded to temperature changes in a similar ways as the PUR resin. The shear strength of wood joints with EPI resins...

  12. Single-donor islet transplantation in type 1 diabetes: patient selection and special considerations

    Directory of Open Access Journals (Sweden)

    Tatum JA

    2017-02-01

    Full Text Available Jacob A Tatum,* Max O Meneveau,* Kenneth L Brayman Department of Surgery, Division of Transplantation, The University of Virginia Health System, Charlottesville, VA, USA *These authors contributed equally to this work. Abstract: Type 1 diabetes mellitus is an autoimmune disorder of the endocrine pancreas that currently affects millions of people in the United States. Although the disease can be managed with exogenous insulin administration, the ultimate cure for the condition lies in restoring a patient’s ability to produce their own insulin. Islet cell allotransplantation provides a means of endogenous insulin production. Though far from perfected, islet transplants are now a proven treatment for type 1 diabetics. However, proper patient selection is critical for achieving optimal outcomes. Given the shortage of transplantable organs, selecting appropriate candidates for whom the procedure will be of greatest benefit is essential. Although many of those who receive islets do not retain insulin independence, grafts do play a significant role in preventing hypoglycemic episodes that can be quite detrimental to quality of life and potentially fatal. Additionally, islet transplant requires lifelong immunosuppression. Antibodies, both preformed and following islet infusion, may play important roles in graft outcomes. Finally, no procedure is without inherent risk and islet transfusions can have serious consequences for recipients’ livers in the form of both vascular and metabolic complications. Therefore, patient-specific factors that should be taken into account before islet transplantation include aims of therapy, sensitization, and potential increased risk for hepatic and portal-venous sequelae. Keywords: islet transplantation, diabetes mellitus type 1, brittle diabetes, single donor, patient

  13. Comparative genomics of the white-rot fungi, Phanerochaete carnosa and P. chrysosporium, to elucidate the genetic basis of the distinct wood types they colonize

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Hitoshi; MacDonald, Jacqueline; Syed, Khajamohiddin; Salamov, Asaf; Hori, Chiaki; Aerts, Andrea; Henrissat, Bernard; Wiebenga, Ad; vanKuyk, Patricia A.; Barry, Kerrie; Lindquist, Erika; LaButti, Kurt; Lapidus, Alla; Lucas, Susan; Coutinho, Pedro; Gong, Yunchen; Samejima, Masahiro; Mahadevan, Radhakrishnan; Abou-Zaid, Mamdouh; de Vries, Ronald P.; Igarashi, Kiyohiko; Yadav, Jagit S.; Grigoriev, Igor V.; Master, Emma R.

    2012-02-17

    Background Softwood is the predominant form of land plant biomass in the Northern hemisphere, and is among the most recalcitrant biomass resources to bioprocess technologies. The white rot fungus, Phanerochaete carnosa, has been isolated almost exclusively from softwoods, while most other known white-rot species, including Phanerochaete chrysosporium, were mainly isolated from hardwoods. Accordingly, it is anticipated that P. carnosa encodes a distinct set of enzymes and proteins that promote softwood decomposition. To elucidate the genetic basis of softwood bioconversion by a white-rot fungus, the present study reports the P. carnosa genome sequence and its comparative analysis with the previously reported P. chrysosporium genome. Results P. carnosa encodes a complete set of lignocellulose-active enzymes. Comparative genomic analysis revealed that P. carnosa is enriched with genes encoding manganese peroxidase, and that the most divergent glycoside hydrolase families were predicted to encode hemicellulases and glycoprotein degrading enzymes. Most remarkably, P. carnosa possesses one of the largest P450 contingents (266 P450s) among the sequenced and annotated wood-rotting basidiomycetes, nearly double that of P. chrysosporium. Along with metabolic pathway modeling, comparative growth studies on model compounds and chemical analyses of decomposed wood components showed greater tolerance of P. carnosa to various substrates including coniferous heartwood. Conclusions The P. carnosa genome is enriched with genes that encode P450 monooxygenases that can participate in extractives degradation, and manganese peroxidases involved in lignin degradation. The significant expansion of P450s in P. carnosa, along with differences in carbohydrate- and lignin-degrading enzymes, could be correlated to the utilization of heartwood and sapwood preparations from both coniferous and hardwood species.

  14. Computational Analysis of Single Nucleotide Polymorphisms Associated with Altered Drug Responsiveness in Type 2 Diabetes

    Directory of Open Access Journals (Sweden)

    Valerio Costa

    2016-06-01

    Full Text Available Type 2 diabetes (T2D is one of the most frequent mortality causes in western countries, with rapidly increasing prevalence. Anti-diabetic drugs are the first therapeutic approach, although many patients develop drug resistance. Most drug responsiveness variability can be explained by genetic causes. Inter-individual variability is principally due to single nucleotide polymorphisms, and differential drug responsiveness has been correlated to alteration in genes involved in drug metabolism (CYP2C9 or insulin signaling (IRS1, ABCC8, KCNJ11 and PPARG. However, most genome-wide association studies did not provide clues about the contribution of DNA variations to impaired drug responsiveness. Thus, characterizing T2D drug responsiveness variants is needed to guide clinicians toward tailored therapeutic approaches. Here, we extensively investigated polymorphisms associated with altered drug response in T2D, predicting their effects in silico. Combining different computational approaches, we focused on the expression pattern of genes correlated to drug resistance and inferred evolutionary conservation of polymorphic residues, computationally predicting the biochemical properties of polymorphic proteins. Using RNA-Sequencing followed by targeted validation, we identified and experimentally confirmed that two nucleotide variations in the CAPN10 gene—currently annotated as intronic—fall within two new transcripts in this locus. Additionally, we found that a Single Nucleotide Polymorphism (SNP, currently reported as intergenic, maps to the intron of a new transcript, harboring CAPN10 and GPR35 genes, which undergoes non-sense mediated decay. Finally, we analyzed variants that fall into non-coding regulatory regions of yet underestimated functional significance, predicting that some of them can potentially affect gene expression and/or post-transcriptional regulation of mRNAs affecting the splicing.

  15. Wood adhesives : vital for producing most wood products

    Science.gov (United States)

    Charles R. Frihart

    2011-01-01

    A main route for the efficient utilization of wood resources is to reduce wood to small pieces and then bond them together (Frihart and Hunt 2010). Although humankind has been bonding wood since early Egyptian civilizations, the quality and quantity of bonded wood products has increased dramatically over the past 100 years with the development of new adhesives and...

  16. Application of FTIR spectroscopy to the characterization of archeological wood.

    Science.gov (United States)

    Traoré, Mohamed; Kaal, Joeri; Martínez Cortizas, Antonio

    2016-01-15

    Two archeological wood samples were studied by attenuated total reflectance Fourier transform infrared (FTIR-ATR) spectroscopy. They originate from a shipwreck in Ribadeo Bay in the northwest of Spain and from a beam wood of an old nave of the Cathedral of Segovia in the central Spain. Principal component analysis was applied to the transposed data matrix (samples as columns and spectral bands as rows) of 43 recorded spectra (18 in the shipwreck and 25 in the beam wood). The results showed differences between the two samples, with a larger proportion of carbohydrates and smaller proportion of lignin in the beam than in the shipwreck wood. Within the beam wood, lignin content was significantly lower in the recent than the old tree rings (P=0.005). These variations can be attributed to species differences between the two woods (oak and pine respectively), with a mixture of guaiacyl and syringyl in hardwood lignin, whereas softwood lignin consists almost exclusively of guaiacyl moieties. The influence of environmental conditions on the FTIR fingerprint was probably reflected by enhanced oxidation of lignin in aerated conditions (beam wood) and hydrolysis of carbohydrates in submerged-anoxic conditions (shipwreck wood). Molecular characterization by analytical pyrolysis of selected samples from each wood type confirmed the interpretation of the mechanisms behind the variability in wood composition obtained by the FTIR-ATR. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Public participation GIS for improving wood burning emissions from residential heating and urban environmental management.

    Science.gov (United States)

    López-Aparicio, Susana; Vogt, Matthias; Schneider, Philipp; Kahila-Tani, Maarit; Broberg, Anna

    2017-04-15

    A crowdsourcing study supported by a public participation GIS tool was designed and carried out in two Norwegian regions. The aim was to improve the knowledge about emissions from wood burning for residential heating in urban areas based on the collection of citizens' localized insights. We focus on three main issues: 1) type of dwelling and residential heating source; 2) wood consumption and type of wood appliances; and 3) citizens' perception of the urban environment. Our study shows the importance of wood burning for residential heating, and of the resulted particle emissions, in Norwegian urban areas. Citizens' localized insights on environmental perception highlight the areas in the city that require particular attention as part of clean air strategies. Information about environmental perception is combined with existing environmental data showing certain correlation. The results support the urban environmental management based on co-benefit approaches, achieving several outcomes from a single policy measure. Measures to reduce urban air pollution will have a positive impact on the citizens' environmental perception, and therefore on their quality of life, in addition to reducing the negative consequences of air pollution on human health. The characterization of residential heating by fuelwood is still a challenging activity. Our study shows the potential of a crowdsourcing method as means for bottom-up approaches designed to increase our knowledge on human activities at urban scale that result on emissions. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  18. Mechanical performance of wood plastic composites containing decayed wood

    OpenAIRE

    Ayrılmış, Nadir; Kaymakcı, Alperen; Güleç, Türker

    2014-01-01

    This study investigated the potential use of the decayed wood in the manufacture of wood plastic composite (WPC) panel. Scots pine (Pinus sylvestris) sound wood and decayed wood (brown-rot fungi) were used as wood material. Three levels of 30%, 40%, and 50% of sound wood and decayed wood, based on the composition by weight, were mixed with the polypropylene with 3% (based on weight) maleic anhydride grafted PP (MAPP) as a coupling agent. The compound pellets were prepared from twin screw co-r...

  19. WHITE DWARF/M DWARF BINARIES AS SINGLE DEGENERATE PROGENITORS OF TYPE Ia SUPERNOVAE

    International Nuclear Information System (INIS)

    Wheeler, J. Craig

    2012-01-01

    Limits on the companions of white dwarfs in the single-degenerate scenario for the origin of Type Ia supernovae (SNe Ia) have gotten increasingly tight, yet igniting a nearly Chandrasekhar mass C/O white dwarf from a condition of near hydrostatic equilibrium provides compelling agreement with observed spectral evolution. The only type of non-degenerate stars that survive the tight limits, M V ∼> 8.4 on the SN Ia in SNR 0509-67.5 and M V ∼> 9.5 in the remnant of SN 1572, are M dwarfs. While M dwarfs are observed in cataclysmic variables, they have special properties that have not been considered in most work on the progenitors of SNe Ia: they have small but finite magnetic fields and they flare frequently. These properties are explored in the context of SN Ia progenitors. White dwarf/M dwarf pairs may be sufficiently plentiful to provide, in principle, an adequate rate of explosions even with slow orbital evolution due to magnetic braking or gravitational radiation. Even modest magnetic fields on the white dwarf and M dwarf will yield adequate torques to lock the two stars together, resulting in a slowly rotating white dwarf, with the magnetic poles pointing at one another in the orbital plane. The mass loss will be channeled by a 'magnetic bottle' connecting the two stars, landing on a concentrated polar area on the white dwarf. This enhances the effective rate of accretion compared to spherical accretion. Luminosity from accretion and hydrogen burning on the surface of the white dwarf may induce self-excited mass transfer. The combined effects of self-excited mass loss, polar accretion, and magnetic inhibition of mixing of accretion layers give possible means to beat the 'nova limit' and grow the white dwarf to the Chandrasekhar mass even at rather moderate mass accretion rates.

  20. Designing Kerr interactions using multiple superconducting qubit types in a single circuit

    Science.gov (United States)

    Elliott, Matthew; Joo, Jaewoo; Ginossar, Eran

    2018-02-01

    The engineering of Kerr interactions is of great interest for processing quantum information in multipartite quantum systems and for investigating many-body physics in a complex cavity-qubit network. We study how coupling multiple different types of superconducting qubits to the same cavity modes can be used to modify the self- and cross-Kerr effects acting on the cavities and demonstrate that this type of architecture could be of significant benefit for quantum technologies. Using both analytical perturbation theory results and numerical simulations, we first show that coupling two superconducting qubits with opposite anharmonicities to a single cavity enables the effective self-Kerr interaction to be diminished, while retaining the number splitting effect that enables control and measurement of the cavity field. We demonstrate that this reduction of the self-Kerr effect can maintain the fidelity of coherent states and generalised Schrödinger cat states for much longer than typical coherence times in realistic devices. Next, we find that the cross-Kerr interaction between two cavities can be modified by coupling them both to the same pair of qubit devices. When one of the qubits is tunable in frequency, the strength of entangling interactions between the cavities can be varied on demand, forming the basis for logic operations on the two modes. Finally, we discuss the feasibility of producing an array of cavities and qubits where intermediary and on-site qubits can tune the strength of self- and cross-Kerr interactions across the whole system. This architecture could provide a way to engineer interesting many-body Hamiltonians and be a useful platform for quantum simulation in circuit quantum electrodynamics.

  1. Cord Wood Testing in a Non-Catalytic Wood Stove

    Energy Technology Data Exchange (ETDEWEB)

    Butcher, T. [Brookhaven National Lab. (BNL), Upton, NY (United States); Trojanowski, R. [Brookhaven National Lab. (BNL), Upton, NY (United States); Wei, G. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2014-06-30

    EPA Method 28 and the current wood stove regulations have been in-place since 1988. Recently, EPA proposed an update to the existing NSPS for wood stove regulations which includes a plan to transition from the current crib wood fuel to cord wood fuel for certification testing. Cord wood is seen as generally more representative of field conditions while the crib wood is seen as more repeatable. In any change of certification test fuel, there are questions about the impact on measured results and the correlation between tests with the two different fuels. The purpose of the work reported here is to provide data on the performance of a noncatalytic stove with cord wood. The stove selected has previously been certified with crib wood which provides a basis for comparison with cord wood. Overall, particulate emissions were found to be considerably higher with cord wood.

  2. Utilization of non-merchantable wood in Steppe regions

    Energy Technology Data Exchange (ETDEWEB)

    Dobrovol' skil, E.Ya.

    1979-01-01

    A description, with diagram, is given of the design of a small mobile retort developed in the USSR for pyrolysis of unmerchantable wood in the steppe regions. The type of wood considered is the tree and shrub material in shelterbelts, e.g. Cornus sanguinea, Elaeagnus angustifolia, Ribes aureum, Cotinus coggygria (Rhus continus) and Caragana arborescens. Yields of charcoal, settled tar, alcohols, and volatile acids from each of these species are given in % of oven-dry wood for pyrolysis at 320/sup 0/C for 2 h. Comparative data are given for dry distillation of wood of birch, spruce, and pine (400/sup 0/C, 8 h).

  3. Energy balance of a wood biomass combustion process

    International Nuclear Information System (INIS)

    Baggio, P.; Cemin, A.; Grigiante, M.; Ragazzi, M.

    2001-01-01

    This article reports the results of a project developed at the University of Trent dealing with some wood biomass combustion processes. The project has been particularly dedicated to the study of the energetic analysis of the combustion processes that occur on a gasified wood stove of advanced combustion technologies. A considerable number of experimental tests has been carried out making use of different type of wood widely in use in Trentino region. The wood stove is a part of a pilot plant providing an hydraulic circuit equipped with a specific apparatus to measure all the necessary data to determine the energy balance required and specifically the thermal efficiency of the plant [it

  4. Diagnostic accuracy of single photon emission CT in Alzheimer-type dementia

    International Nuclear Information System (INIS)

    Hanyu, Haruki; Abe, Shinei; Arai, Hisayuki; Asano, Tetsuichi; Iwamoto, Toshihiko; Takasaki, Masaru; Suzuki, Takanari

    1992-01-01

    To determine the diagnostic accuracy of single photon emission computed tomography (SPECT) with 123 I-IMP in Alzheimer-type dementia (ATD), we studied 46 ATD patients and 23 healthy controls. The patients fulfilled the NINCDS-ADRDA criteria for probable or definite ATD and were classified as having mild, moderate, and severe ATD by neuropsychological examinations. To assess regional cerebral blood flow, we performed qualitative SPECT image analysis without any knowledge of the subject's clinical classification. The image was regarded as abnormal if cerebral blood flow was reduced in the unlilateral or bilateral temporoparietal association areas, with or without any reduction of flow in other brain regions. The diagnostic sensitivity (abnormal image/ patient) of 123 I-IMP SPECT in mild, moderate and severe ATD was 67%, 86% and 92%, because an abnormal image was found in only 2/23 healthy controls. Eight ATD patients without reduced temporoparietal perfusion showed normal perfusion or frontal hypoperfusion. These results suggest that 123 I-IMP SPECT may provide an accurate and sensitive diagnostic marker for ATD. The detection of these characteristic abnormalities of cerebral perfusion could well be applied to the clinical diagnosis of ATD. (author)

  5. Chapter 6: Wood energy and competing wood product markers

    Science.gov (United States)

    Kenneth E. Skog; Robert C. Abt; Karen Abt

    2014-01-01

    Understanding the effect of expanding wood energy markets is important to all wood-dependent industries and to policymakers debating the implementation of public programs to support the expansion of wood energy generation. A key factor in determining the feasibility of wood energy projects (e.g. wood boiler or pellet plant) is the long-term (i.e. 20-30year) supply...

  6. Wood wastes: Uses

    International Nuclear Information System (INIS)

    Cipro, A.

    1993-01-01

    The 1,500 industrial firms manufacturing furniture in the Italian Province of Treviso can generate up to 190,000 tonnes of wood wastes annually. In line with the energy conservation-environmental protection measures contained in Italian Law No. 475/88, this paper indicates convenient uses for these wood wastes - as a raw material for fibreboards or as a fuel to be used in the furniture manufacturing plants themselves and in kilns producing lime. Reference is made to the wood wastes gasification/power generation system being developed by ENEA (the Italian Agency for New Technology, Energy and the Environment)

  7. Fatigue Damage in Wood

    DEFF Research Database (Denmark)

    Clorius, Christian Odin; Pedersen, Martin Bo Uhre; Hoffmeyer, Preben

    1996-01-01

    An investigation of fatigue failure in wood subjected to load cycles in compression parallel to grain is presented. Fatigue failure is found to depend both on the total time under load and on the number of cycles.Recent accelerated fatigue research on wood is reviewed, and a discrepancy between...... to 10 Hz are used. The number of cycles to failure is found to be a poor measure of the fatigue performance of wood. Creep, maximum strain, stiffness and work are monitored throughout the fatigue tests. Accumulated creep is suggested identified with damage and a correlation between stiffness reduction...

  8. Preliminary studies of Brazilian wood using different radioisotopic sources

    International Nuclear Information System (INIS)

    Carvalho, Gilberto; Silva, Leonardo Gondim de Andrade e

    2013-01-01

    Due to availability and particular features, wood was one of the first materials used by mankind with a wide variety of applications. It can be used as raw material for paper and cellulose manufacturing; in industries such as chemical, naval, furniture, sports goods, toys, and musical instrument; in building construction and in the distribution of electric energy. Wood has been widely researched; therefore, wood researchers know that several aspects such as temperature, latitude, longitude, altitude, sunlight, soil, and rainfall index interfere with the growth of trees. This behavior explains why average physical-chemical properties are important when wood is studied. The majority of researchers consider density to be the most important wood property because of its straight relationship with the physical and mechanical properties of wood. There are three types of wood density: basic, apparent and green. The apparent density was used here at 12% of moisture content. In this study, four different types of wood were used: 'freijo', 'jequetiba', 'muiracatiara' and 'ipe'. For wood density determination by non-conventional method, Am-241, Ba-133 and Cs-137 radioisotopic sources; a NaI scintillation detector and a counter were used. The results demonstrated this technique to be quick and accurate. By considering the nuclear parameters obtained as half value layers and linear absorption coefficients, Cs-137 radioisotopic source demonstrated to be the best option to be used for inspection of the physical integrity of electric wooden poles and live trees for future works. (author)

  9. Evaluating the efficacy of wood shreds for mitigating erosion.

    Science.gov (United States)

    Foltz, Randy B; Copeland, Natalie S

    2009-02-01

    An erosion control product made by shredding on-site woody materials was evaluated for mitigating erosion through a series of rainfall simulations. Tests were conducted on bare soil and soil with 30, 50, and 70% cover on a coarse and a fine-grained soil. Results indicated that the wood product known as wood shreds reduced runoff and soil loss from both soil types. Erosion mitigation ranged from 60 to nearly 100% depending on the soil type and amount of concentrated flow and wood shred cover. Wood shreds appear to be a viable alternative to agricultural straw. A wood shred cover of 50% appears optimal, but the appropriate coverage rate will depend on the amount of expected concentrated flow and soil type.

  10. Disentangling biodiversity and climatic determinants of wood production.

    Science.gov (United States)

    Vilà, Montserrat; Carrillo-Gavilán, Amparo; Vayreda, Jordi; Bugmann, Harald; Fridman, Jonas; Grodzki, Wojciech; Haase, Josephine; Kunstler, Georges; Schelhaas, Martjan; Trasobares, Antoni

    2013-01-01

    Despite empirical support for an increase in ecosystem productivity with species diversity in synthetic systems, there is ample evidence that this relationship is dependent on environmental characteristics, especially in structurally more complex natural systems. Empirical support for this relationship in forests is urgently needed, as these ecosystems play an important role in carbon sequestration. We tested whether tree wood production is positively related to tree species richness while controlling for climatic factors, by analyzing 55265 forest inventory plots in 11 forest types across five European countries. On average, wood production was 24% higher in mixed than in monospecific forests. Taken alone, wood production was enhanced with increasing tree species richness in almost all forest types. In some forests, wood production was also greater with increasing numbers of tree types. Structural Equation Modeling indicated that the increase in wood production with tree species richness was largely mediated by a positive association between stand basal area and tree species richness. Mean annual temperature and mean annual precipitation affected wood production and species richness directly. However, the direction and magnitude of the influence of climatic variables on wood production and species richness was not consistent, and vary dependent on forest type. Our analysis is the first to find a local scale positive relationship between tree species richness and tree wood production occurring across a continent. Our results strongly support incorporating the role of biodiversity in management and policy plans for forest carbon sequestration.

  11. Wood anatomy of the neotropical Sapotaceae. VI, Chloroluma

    Science.gov (United States)

    B. F. Kukachka

    1978-01-01

    The old genus Chloroluma has been reinstated to generic status after having been in synonomy under Chrysophyllum for many years. The description is based on the type species C. gonocarpa which is characterized by: Its clear yellow wood; pores in radial-echelon arrangement; rhombic, two-sized, and microcrystals frequent in the axial parenchyma and wood rays; colored...

  12. A profile of wood use in nonresidential building construction

    Science.gov (United States)

    H. N. Spelter; R. G. Anderson

    This report presents estimates of the amounts of lumber, glued-laminated lumber, trusses, plywood, particleboard, hardboard, and wood shingles used in new nonresidential building construction in the United States. Use of wood products is shown for several building types, project sizes, and building components. The estimates are based on a survey of 489 projects under...

  13. Factors that influence the speed of bacterial wood degradation

    NARCIS (Netherlands)

    Klaassen, R.K.W.M.; Overeem, van B.S.

    2012-01-01

    Bacterial wood decay is a serious threat to the many wooden foundation piles in the Netherlands. In order to learn more about the factors that influence the process of decay, approx. 2000 wood samples taken from Amsterdam piles heads were analysed on type and degree of decay and for 59 extracted

  14. Automatic wood heating: slashing wood into shreds in forest; Chauffage automatique au bois: dechiqueter le bois en foret

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1998-10-01

    Small plates of wood cut to shreds are produced by a specific machine. The proper use of automatic wood-fueled heating plants that use this type of fuel depends on technical and methodological choices to properly organize the production of wood shreds and the supply of heating plants. More than 250 automatic wood-fueled plants were built in France since the beginning of the 80`s and operate in public buildings, schools, hospitals, bloc of flats and heat networks. This guide makes a synthesis of the experience gained in France and Europe and provides the guidelines for the organisation of wood plates production in good conditions (annual production, location of the wood shreds production unit, organisation of the work, means of transportation, equipment..). (J.S.)

  15. Low Temperature Characterization of PMOS-type Gate-all-around Silicon nanowire FETs as single-hole-transistors

    Science.gov (United States)

    Hong, B. H.; Hwang, S. W.; Lee, Y. Y.; Son, M. H.; Ahn, D.; Cho, K. H.; Yeo, K. H.; Kim, D.-W.; Jin, G. Y.; Park, D.

    2011-12-01

    We report the single hole tunneling characteristics observed from a PMOS-type gate-all-around silicon nanowire field-effect-transistor with the radius 5 nm and the length 44 nm. The total capacitance of the quantum dot obtained from the measured Coulomb oscillations and Coulomb diamonds matches with the ideal capacitance of the silicon cylinder. It suggests that the observed single hole tunneling is originated from the fabricated structure.

  16. Characterization of ryanodine receptor type 1 single channel activity using "on-nucleus" patch clamp.

    Science.gov (United States)

    Wagner, Larry E; Groom, Linda A; Dirksen, Robert T; Yule, David I

    2014-08-01

    In this study, we provide the first description of the biophysical and pharmacological properties of ryanodine receptor type 1 (RyR1) expressed in a native membrane using the on-nucleus configuration of the patch clamp technique. A stable cell line expressing rabbit RyR1 was established (HEK-RyR1) using the FLP-in 293 cell system. In contrast to untransfected cells, RyR1 expression was readily demonstrated by immunoblotting and immunocytochemistry in HEK-RyR1 cells. In addition, the RyR1 agonists 4-CMC and caffeine activated Ca(2+) release that was inhibited by high concentrations of ryanodine. On nucleus patch clamp was performed in nuclei prepared from HEK-RyR1 cells. Raising the [Ca(2+)] in the patch pipette resulted in the appearance of a large conductance cation channel with well resolved kinetics and the absence of prominent subconductance states. Current versus voltage relationships were ohmic and revealed a chord conductance of ∼750pS or 450pS in symmetrical 250mM KCl or CsCl, respectively. The channel activity was markedly enhanced by caffeine and exposure to ryanodine resulted in the appearance of a subconductance state with a conductance ∼40% of the full channel opening with a Po near unity. In total, these properties are entirely consistent with RyR1 channel activity. Exposure of RyR1 channels to cyclic ADP ribose (cADPr), nicotinic acid adenine dinucleotide phosphate (NAADP) or dantrolene did not alter the single channel activity stimulated by Ca(2+), and thus, it is unlikely these molecules directly modulate RyR1 channel activity. In summary, we describe an experimental platform to monitor the single channel properties of RyR channels. We envision that this system will be influential in characterizing disease-associated RyR mutations and the molecular determinants of RyR channel modulation. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Oil type and cross-linking influence growth of Aureobasidium melanogenum on vegetable oils as a single carbon source.

    Science.gov (United States)

    Peeters, Loes H M; Huinink, Hendrik P; Voogt, Benjamin; Adan, Olaf C G

    2018-03-12

    Aureobasidium melanogenum is the main fungus found in a spontaneously formed biofilm on a oil-treated wood. This dark colored biofilm functions as a protective coating. To better understand biofilm formation, in this study A. melanogenum was cultured on olive oil and raw linseed oil. Metabolic activity and oil conversion were measured. The results show that A. melanogenum is able to grow on linseed oil and olive oil as a single carbon source. The fungus produces the enzyme lipase to convert the oil into fatty acids and glycerol. Metabolic activity and oil conversion were equal on linseed oil and olive oil. The fungus was not able to grow on severe cross-linked linseed oil, meaning that the degree of cross-linking of the oil is important for growth of A. melanogenum. Dark coloring of the colony was seen on linseed oil, which might be a stress response on the presence of autoxidation products in linseed oil. The colony on olive oil showed delayed melanin production indicating an inhibitory effect of olive oil on melanin production. © 2018 The Authors. MicrobiologyOpen published by John Wiley & Sons Ltd.

  18. A new single nucleotide polymorphisms typing method and device by bioluminometric assay coupled with a photodiode array

    Science.gov (United States)

    Kamahori, Masao; Harada, Kunio; Kambara, Hideki

    2002-11-01

    Easy and inexpensive single nucleotide polymorphisms (SNPs) typing systems are required for the practice of genetic testing as well as genetic medicine. Most of the SNPs typing systems use laser-induced fluorescence detection coupled with fluorophore tagging on DNA, which are expensive. A new simple and inexpensive SNPs typing system is presented. It uses a bioluminometric assay coupled with modified primer extension reactions and an inexpensive photodiode array for the luminometric detection. The reagents consumed in the assay are also inexpensive. Although the system is very small, simple and inexpensive, it gives enough sensitivity for detecting target DNAs as small as 10 fmol, which is good enough for SNPs typing.

  19. Laser characterisation of a 3D single-type column p-type prototype module read out with ATLAS SCT electronics

    International Nuclear Information System (INIS)

    Ehrich, T.; Kuehn, S.; Boscardin, M.; Dalla Betta, G.-F.; Eckert, S.; Jakobs, K.; Maassen, M.; Parzefall, U.; Piemonte, C.; Pozza, A.; Ronchin, S.; Zorzi, N.

    2007-01-01

    In this paper measurements of a 3D single-type column (3D-stc) microstrip silicon device are shown. The 3D-stc sensor has n-type columns in p-type substrate. It has been connected to an ATLAS SCT ABCD3T chip and is readout with ATLAS SCT electronics at 40 MHz. Spatial measurements were done with a laser setup to investigate the expected low field region in 3D devices. An influence of the p-stops on the collected charge has been observed

  20. Laser characterisation of a 3D single-type column p-type prototype module read out with ATLAS SCT electronics

    Energy Technology Data Exchange (ETDEWEB)

    Ehrich, T. [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder Str. 3, 79104 Freiburg (Germany); Kuehn, S. [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder Str. 3, 79104 Freiburg (Germany)], E-mail: susanne.kuehn@physik.uni-freiburg.de; Boscardin, M.; Dalla Betta, G.-F. [ITC-irst Trento, Microsystems Division, via Sommarive, 18 38050 Povo di Trento (Italy); Eckert, S.; Jakobs, K.; Maassen, M.; Parzefall, U. [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder Str. 3, 79104 Freiburg (Germany); Piemonte, C.; Pozza, A.; Ronchin, S.; Zorzi, N. [ITC-irst Trento, Microsystems Division, via Sommarive, 18 38050 Povo di Trento (Italy)

    2007-12-11

    In this paper measurements of a 3D single-type column (3D-stc) microstrip silicon device are shown. The 3D-stc sensor has n-type columns in p-type substrate. It has been connected to an ATLAS SCT ABCD3T chip and is readout with ATLAS SCT electronics at 40 MHz. Spatial measurements were done with a laser setup to investigate the expected low field region in 3D devices. An influence of the p-stops on the collected charge has been observed.

  1. Non_standard Wood

    DEFF Research Database (Denmark)

    Tamke, Martin

    . Using parametric design tools and computer controlled production facilities Copenhagens Centre for IT and Architecture undertook a practice based research into performance based non-standard element design and mass customization techniques. In close cooperation with wood construction software......Non-Standard elements in architecture bear the promise of a better more specific performance (Oosterhuis 2003). A new understanding of design evolves, which is focusing on open ended approaches, able to negotiate between shifting requirements and to integrate knowledge on process and material......, but the integration of traditional wood craft techniques. The extensive use of self adjusting, load bearing wood-wood joints contributed to ease in production and assembly of a performance based architecture....

  2. Factors associated with serum B-type natriuretic peptide in infants with single ventricles.

    Science.gov (United States)

    Butts, Ryan J; Zak, Victor; Hsu, Daphne; Cnota, James; Colan, Steven D; Hehir, David; Kantor, Paul; Levine, Jami C; Margossian, Renee; Richmond, Marc; Szwast, Anita; Williams, Derek; Williams, Richard; Atz, Andrew M

    2014-06-01

    Data regarding the value of B-type natriuretic peptide (BNP) measurements in infants with a single-ventricle (SV) physiology are lacking. This analysis aimed to describe the BNP level changes in infants with an SV physiology before and after superior cavopulmonary connection (SCPC) surgery. Levels of BNP were measured by a core laboratory before SCPC (at 5.0 ± 1.6 months) and at the age of 14 months during a multicenter trial of angiotensin-converting enzyme inhibition therapy for infants with SV. Multivariable longitudinal analysis was used to model the associations between BNP levels and three sets of grouped variables (echocardiography, catheterization, growth). Multivariable analysis was performed to assess associations with patient characteristics at both visits. Associations between BNP levels and neurodevelopmental variables were investigated at the 14 month visit because neurodevelopmental assessment was performed only at this visit. The BNP level was significantly higher before SCPC (n = 173) than at the age of 14 months (n = 134). The respective median levels were 80.8 pg/ml (interquartile range [IQR], 35-187 pg/ml) and 34.5 pg/ml (IQR, 17-67 pg/ml) (p SCPC and in 21 subjects (16 %) at the age of 14 months. In the 117 patients who had BNP measurements at both visits, the median BNP level decreased 32 pg/ml (IQR, 1-79 pg/ml) (p SCPC surgery (p SCPC surgery (p = 0.04), and a lower Bayley psychomotor developmental index (p = 0.02). The levels of BNP decreases in infants with SV from the pre-SCPC visit to the age of 14 months. A higher BNP level is associated with increased ventricular dilation in systole, increased AV valve regurgitation, impaired growth, and poorer neurodevelopmental outcomes. Therefore, BNP level may be a useful seromarker for identifying infants with SV at risk for worse outcomes.

  3. Interaction of iron status with single nucleotide polymorphisms on incidence of type 2 diabetes.

    Directory of Open Access Journals (Sweden)

    Jihye Kim

    Full Text Available The objective of this study is to find single nucleotide polymorphisms (SNPs associated with a risk of Type 2 diabetes (T2D in Korean adults and to investigate the longitudinal association between these SNPs and T2D and the interaction effects of iron intake and average hemoglobin level. Data from the KoGES_Ansan and Ansung Study were used. Gene-iron interaction analysis was conducted using a two-step approach. To select candidate SNPs associated with T2D, a total of 7,935 adults at baseline were included in genome-wide association analysis (step one. After excluding T2D prevalent cases, prospective analyses were conducted with 7,024 adults aged 40-69 (step two. The association of selected SNPs and iron status with T2D and their interaction were determined using a Cox proportional hazard model. A total of 3 SNPs [rs9465871 (CDKAL1, rs10761745 (JMJD1C, and rs163177 (KCNQ1] were selected as candidate SNPs related to T2D. Among them, rs10761745 (JMJD1C and rs163177 (KCNQ1 were prospectively associated with T2D. High iron intake was also prospectively associated with the risk of T2D after adjusting for covariates. Average hemoglobin level was positively associated with T2D after adjusting for covariates in women. We also found significant interaction effects between rs10761745 (JMJD1C and average hemoglobin levels on the risk of T2D among women with normal inflammation and without anemia at baseline. In conclusion, KCNQ1 and JMJD1C may prospectively contribute to the risk of T2D incidence among adults over the age of 40 and JMJD1C, but CDKAL1 may not, and iron status may interactively contribute to T2D incidence in women.

  4. Surface properties of alumino-silicate single-walled nanotubes of the imogolite type.

    Science.gov (United States)

    Bonelli, Barbara; Armandi, Marco; Garrone, Edoardo

    2013-08-28

    An IR spectroscopy study is reported on the nature and accessibility of external and internal surfaces of single-walled alumino-silicate nanotubes (NTs) of the imogolite type. NTs form bundles with hexagonal symmetry, in which three kinds of surfaces may be figured out: surface A is the inner surface of NTs; surface B is that between three aligned NTs in the hexagonal packing; and surface C arises from slit mesopores between bundles. Two materials were considered: proper imogolite (IMO, (OH)3Al2O3SiOH) and its methylated analogue, (Me-IMO, (OH)3Al2O3SiCH3). The chemical nature of the outer surface of NTs is the same in both materials, i.e. a curved gibbsite sheet with both Al-OH-Al and Al-O-Al groups and an amphoteric character. The inner surface is very hydrophilic in IMO NTs, lined by closely packed silanols, and hydrophobic in Me-IMO, all silanols being replaced by -SiCH3 groups. The change in chemical composition is accompanied by an increment in pore size, about 1.0 nm in IMO, and ca. 2.0 nm in Me-IMO, which implies a change in the accessibility of the B surface, not available to any molecule in IMO, and accessible in Me-IMO to small molecules like water, due to larger pores between NTs. Aluminol species at the B surface display an acidic nature, in contrast with that of the same species at surface C, because of a confinement effect.

  5. Single cell-type comparative metabolomics of epidermal bladder cells from the halophyte Mesembryanthemum crystallinum.

    Directory of Open Access Journals (Sweden)

    Bronwyn Jane Barkla

    2015-06-01

    Full Text Available One of the remarkable adaptive features of the halophyte and facultative CAM plant Mesembryathemum crystallinum are the specialized modified trichomes called epidermal bladder cells (EBC which cover the leaves, stems, and peduncle of the plant. They are present from an early developmental stage but upon salt stress rapidly expand due to the accumulation of water and sodium. This particular plant feature makes it an attractive system for single cell type studies, with recent proteomics and transcriptomics studies of the EBC establishing that these cells are metabolically active and have roles other than sodium sequestration. To continue our investigation into the function of these unusual cells we carried out a comprehensive global analysis of the metabolites present in the EBC extract by gas chromatography Time-of-Flight mass spectrometry (GC-TOF and identified 194 known and 722 total molecular features. Statistical analysis of the metabolic changes between control and salt-treated samples was used to identify 352 significantly differing metabolites (268 after correction for FDR. Principal components analysis provided an unbiased evaluation of the data variance structure. Biochemical pathway enrichment analysis suggested significant perturbations in 13 biochemical pathways as defined in KEGG. More than 50% of the metabolites that show significant changes in the EBC, can be classified as compatible solutes and include sugars, sugar alcohols, protein and non-protein amino acids, and organic acids, highlighting the need to maintain osmotic homeostasis to balance the accumulation of Na and Cl ions. Overall, the comparison of metabolic changes in salt treated relative to control samples suggest large alterations in Mesembryanthemum crystallinum epidermal bladder cells.

  6. CHARACTERISTICS OF LAMINATED WOOD OF LOGGING WASTE OF THREE NATURAL FOREST WOOD SPECIES

    Directory of Open Access Journals (Sweden)

    Jamaludin Malik

    2005-03-01

    Full Text Available This research is aimed to assess the characteristics of 3-ply laminated wood assembly incorporating wood waste belonged to three species i.e. bengkal (Nauclea sp., pisang-pisang (Alponsea teysmanii Boerl, and jambu-jambu (Eugenia spp..  The waste was procured from logged natural forests. The used adhesive was tannin-resorcinol formaldehyde.  The lamination experiment was replicated three times. The assessed characteristics were moisture content, density, formaldehyde emission, bonding strength, wood defect, and static bending strength. The resulting 3-ply laminated wood assembly (beam has a moisture content at 4.00 - 13.90%, density 0.30 - 0.68 gram per cm3, and formaldehyde emission 0.323 - 3.199 mg per liter that tended to increase with the decrease in density of the laminated wood.  The bonding strength of the laminated wood ranges varied from 47.14 to 107.52 kg per cm2  (dry testing and 40.76 - 79.57 kg per cm2  (wet testing.  Likewise, wood defect was about 80 - 100% (dry test and 20 - 80% (wet test.  Static bending strength varied from 455.62 - 843.36 kg per cm2 (for MOE and from 35,985.49 to 104,332.63 kg per cm2 (for MOR. Based on these data, the three wood waste species afforded good bending strength and they were suitable for reconstituting material for exterior-type laminated wood beam.

  7. Common questions and concerns from government users of industrial treated wood products

    Science.gov (United States)

    Stan Lebow; James Wacker

    2011-01-01

    Because pressure-treated wood is perceived as economical and relatively easy to install, federal, state and local government agencies sometimes utilize treated wood for industrial-type applications. When these agencies have questions or concerns about treated wood they may make inquiries to the US Forest Products Laboratory. These inquiries provide an indication of...

  8. Controlling moisture content of wood samples using a modified soil-pan decay method

    Science.gov (United States)

    Jerrold E. Winandy; Simon F. Curling; Patricia K. Lebow

    2005-01-01

    In wood, the threshold level below which decay cannot occur varies with species or type of wood product and other factors such as temperature, humidity, and propensity of exposure or service-use to allow rain-induced wetting and subsequent drying. The ability to control wood moisture content (MC) during laboratory decay testing could allow research on the moisture...

  9. Influence of moisture absorption on mechanical properties of wood flour- polypropylene composites

    Science.gov (United States)

    Nicole Stark

    2001-09-01

    Wood-plastic composites are being examined for a greater number of structural-type applications that may be exposed to different environments, some of them adverse. This paper discusses the influence of moisture absorption on the mechanical proper-ties of wood flour-polypropylene composites. Composites filled with 20% or 40% wood flour (by weight) were placed in...

  10. Typing of 49 autosomal SNPs by single base extension and capillary electrophoresis for forensic genetic testing

    DEFF Research Database (Denmark)

    Børsting, Claus; Tomas Mas, Carmen; Morling, Niels

    2012-01-01

    We describe a method for simultaneous amplification of 49 autosomal single nucleotide polymorphisms (SNPs) by multiplex PCR and detection of the SNP alleles by single base extension (SBE) and capillary electrophoresis. All the SNPs may be amplified from only 100 pg of genomic DNA and the length...

  11. Highly similar prokaryotic communities of sunken wood at shallow and deep-sea sites across the oceans.

    Science.gov (United States)

    Palacios, Carmen; Zbinden, Magali; Pailleret, Marie; Gaill, Françoise; Lebaron, Philippe

    2009-11-01

    With an increased appreciation of the frequency of their occurrence, large organic falls such as sunken wood and whale carcasses have become important to consider in the ecology of the oceans. Organic-rich deep-sea falls may play a major role in the dispersal and evolution of chemoautotrophic communities at the ocean floor, and chemosynthetic symbiotic, free-living, and attached microorganisms may drive the primary production at these communities. However, little is known about the microbiota thriving in and around organic falls. Our aim was to investigate and compare free-living and attached communities of bacteria and archaea from artificially immersed and naturally sunken wood logs with varying characteristics at several sites in the deep sea and in shallow water to address basic questions on the microbial ecology of sunken wood. Multivariate indirect ordination analyses of capillary electrophoresis single-stranded conformation polymorphisms (CE-SSCP) fingerprinting profiles demonstrated high similarity of bacterial and archaeal assemblages present in timbers and logs situated at geographically distant sites and at different depths of immersion. This similarity implies that wood falls harbor a specialized microbiota as observed in other ecosystems when the same environmental conditions reoccur. Scanning and transmission electron microscopy observations combined with multivariate direct gradient analysis of Bacteria CE-SSCP profiles demonstrate that type of wood (hard vs. softwood), and time of immersion are important in structuring sunken wood bacterial communities. Archaeal populations were present only in samples with substantial signs of decay, which were also more similar in their bacterial assemblages, providing indirect evidence of temporal succession in the microbial communities that develop in and around wood falls.

  12. The inactivation of single-chain urokinase-type plasminogen activator by thrombin in a plasma milieu : effect of thrombomodulin

    NARCIS (Netherlands)

    Braat, E.A.M.; Los, P.; Rijken, D.C.

    1998-01-01

    Thrombin cleaves single-chain urokinase-type plasminogen activator (scu- PA) into a virtually inactive two-chain form (tcu-PA/T), a process which may contribute to the maintenance of a fresh blood clot. We have examined the inactivation of scu-PA by thrombin in a plasma milieu to get more insight in

  13. Types and Dynamics of Gendered Space: A Case of Emirati Female Learners in a Single-Gender Context

    Science.gov (United States)

    Alzeer, Gergana

    2018-01-01

    This article is concerned with gendered spaces as they emerge from exploring Emirati female learners' spatiality in a single-gender context. By conducting ethnographic research and utilising Lefebvre's triad of perceived, conceived and lived space for the analysis and categorisation of students' spaces, three types of gendered spaces emerged:…

  14. The influence of the type of embryo culture medium on neonatal birthweight after single embryo transfer in IVF

    NARCIS (Netherlands)

    Vergouw, C.G.; Kostelijk, E.H.; Doejaaren, E.; Hompes, P.G.A.; Lambalk, C.B.; Schats, R.

    2012-01-01

    STUDY QUESTION Does the type of medium used to culture fresh and frozenthawed embryos influence neonatal birthweight after single embryo transfer (SET) in IVF? SUMMARY ANSWER A comparison of two commercially available culture media showed no significant influence on mean birthweight and mean

  15. Comparative ecobalancing accounting of semi-central house heat supply from wood residues

    International Nuclear Information System (INIS)

    Biemann, Kirsten

    2015-01-01

    impact. Heat demanders and network structure vary for the different settlement types. This impacts the heat losses and the amount of energy generated from wood in the network. Combined heat and power plants promise higher fuel utilization. They decrease costs and environmental impacts. The heat losses in the network vary greatly between 23 percent for small single-family houses and 4 percent for big multi-family buildings. Therefore networks with bigger heat demanders have lower environmental burdens. From an economic point of view the conversion from a gas heater to the connection of a multi- family building to a semi- centralized heating network using wood residues as fuel is worthwhile. However for a single-family building this is often not the case. A comparison between the semi- centralized heat supply from wood residues and the commonly used heat supply from gas heaters shows a large potential to decrease greenhouse gas emissions, ozone depletion and fossil resource usage when using the first variant. However, it increases particulate matter formation, photochemical oxidant formation, eutrophication, and acidification. Only the usage of a wood gasification and a combined heat and power plant decreases particulate matter formation slightly. Similar results were obtained for a centralized heating network using wood residues as fuel. Using wood heaters in the buildings further decreases greenhouse gas emissions, ozone depletion and fossil resources, but results in an increased particulate matter formation. This particulate matter formation is over 1.000 percent bigger than for gas heaters.

  16. Lion (Panthera leo) and caracal (Caracal caracal) type IIx single muscle fibre force and power exceed that of trained humans.

    Science.gov (United States)

    Kohn, Tertius A; Noakes, Timothy D

    2013-03-15

    This study investigated for the first time maximum force production, shortening velocity (Vmax) and power output in permeabilised single muscle fibres at 12°C from lion, Panthera leo (Linnaeus 1758), and caracal, Caracal caracal (Schreber 1776), and compared the values with those from human cyclists. Additionally, the use and validation of previously frozen tissue for contractile experiments is reported. Only type IIx muscle fibres were identified in the caracal sample, whereas type IIx and only two type I fibres were found in the lion sample. Only pure type I and IIa, and hybrid type IIax fibres were identified in the human samples - there were no pure type IIx fibres. Nevertheless, compared with all the human fibre types, the lion and caracal fibres were smaller (Plion: 3008±151 μm(2), caracal: 2583±221 μm(2)). On average, the felid type IIx fibres produced significantly greater force (191-211 kN m(-2)) and ~3 times more power (29.0-30.3 kN m(-2) fibre lengths s(-1)) than the human IIax fibres (100-150 kN m(-2), 4-11 kN m(-2) fibre lengths s(-1)). Vmax values of the lion type IIx fibres were also higher than those of human type IIax fibres. The findings suggest that the same fibre type may differ substantially between species and potential explanations are discussed.

  17. Wood for the trees

    Directory of Open Access Journals (Sweden)

    Rob Garbutt

    2013-10-01

    Full Text Available Our paper focuses on the materiality, cultural history and cultural relations of selected artworks in the exhibition Wood for the trees (Lismore Regional Gallery, New South Wales, Australia, 10 June – 17 July 2011. The title of the exhibition, intentionally misreading the aphorism “Can’t see the wood for the trees”, by reading the wood for the resource rather than the collective wood[s], implies conservation, preservation, and the need for sustaining the originating resource. These ideas have particular resonance on the NSW far north coast, a region once rich in rainforest. While the Indigenous population had sustainable practices of forest and land management, the colonists deployed felling and harvesting in order to convert the value of the local, abundant rainforest trees into high-value timber. By the late twentieth century, however, a new wave of settlers launched a protest movements against the proposed logging of remnant rainforest at Terania Creek and elsewhere in the region. Wood for the trees, curated by Gallery Director Brett Adlington, plays on this dynamic relationship between wood, trees and people. We discuss the way selected artworks give expression to the themes or concepts of productive labour, nature and culture, conservation and sustainability, and memory. The artworks include Watjinbuy Marrawilil’s (1980 Carved ancestral figure ceremonial pole, Elizabeth Stops’ (2009/10 Explorations into colonisation, Hossein Valamanesh’s (2008 Memory stick, and AñA Wojak’s (2008 Unread book (in a forgotten language. Our art writing on the works, a practice informed by Bal (2002, Muecke (2008 and Papastergiadis (2004, becomes a conversation between the works and the themes or concepts. As a form of material excess of the most productive kind (Grosz, 2008, p. 7, art seeds a response to that which is in the air waiting to be said of the past, present and future.

  18. Analysis of existing structure and emissions of wood combustion plants for the production of heat and electricity in Bavaria; Analyse der Bestandesstruktur und der Emissionen von Holzfeuerungsanlagen zur Erzeugung von Waerme und Strom in Bayern.

    Energy Technology Data Exchange (ETDEWEB)

    Joa, Bettina

    2014-07-01

    This work deals with the detailed analysis of the existing structure of all Bavarian wood burning plants for the generation of heat and electricity as well as the determination of the resulting emission emissions in 2013. The number of wood burning plants in the single-chamber fireplaces, wood central heating and wood-fired heating plants which are in operation in the year 2013 were determined, and how many plants are existing in the various areas like pellet stoves, traditional ovens, wood-burning fireplace, pellet central heating systems, wood chips central heating systems, fire-wood central heating systems, wood combined heat and power plant (electricity and heat) and wood power plants (heat). In addition, the regional distribution of the wood burning plants in the Bavarian governmental districts is investigated as well as the type and amount of energy produced by them (heat, electricity). [German] Diese Arbeit behandelt die detaillierte Analyse der Bestandesstruktur saemtlicher bayerischer Holzfeuerungsanlagen zur Erzeugung von Waerme und Strom sowie die Ermittlung des dabei entstehenden Emissionsausstosses im Jahr 2013. Dabei wurde ermittelt wie viele Holzfeuerungsanlagen in den Segmenten Einzelraumfeuerstaetten, Holz-Zentralheizungen und Holzheiz(kraft)werke im Jahr 2013 in Bayern in Betrieb sind und wie viele Anlagen es in den einzelnen Bereichen Pelletoefen, traditionelle Oefen, Kaminoefen, Heizkamine, offene Kamine, Kacheloefen, Pellet-Zentralheizungen, Hackschnitzel-Zentralheizungen, Scheitholz-Zentralheizungen, Holzheizkraftwerke (Waerme und Strom), Holzheizwerke (Waerme) sowie Holzkraftwerke (Strom) gibt. Des Weiteren wird die regionale Verteilung der Holzfeuerungsanlagen in den bayerischen Regierungsbezirken erforscht sowie die durch sie produzierte Art und Menge an Energie (Waerme, Strom).

  19. Nocturnal Glucose Metabolism in Type 1 Diabetes: A Study Comparing Single Versus Dual Tracer Approaches.

    Science.gov (United States)

    Mallad, Ashwini; Hinshaw, Ling; Dalla Man, Chiara; Cobelli, Claudio; Basu, Rita; Lingineni, Ravi; Carter, Rickey E; Kudva, Yogish C; Basu, Ananda

    2015-08-01

    Understanding the effect size, variability, and underlying physiology of the dawn phenomenon is important for next-generation closed-loop control algorithms for type 1 diabetes (T1D). We used an iterative protocol design to study 16 subjects with T1D on individualized insulin pump therapy for two successive nights. Endogenous glucose production (EGP) rates at 3 a.m. and 7 a.m. were measured with [6,6-(2)H(2)]glucose as a single tracer, infused from midnight to 7 a.m. in all subjects. To explore possibility of tracer recycling due to prolonged [6,6-(2)H(2)]glucose infusion, which was highly probable after preplanned interim data analyses, we infused a second tracer, [6-(3)H]glucose, from 4 a.m. to 7 a.m. in the last seven subjects to measure EGP at 7 a.m. Cortisol concentrations increased during both nights, but changes in glucagon and insulin concentration were inconsistent. Although the plasma glucose concentrations rose from midnight to 7 a.m. during both nights, EGP measured with [6,6-(2)H(2)]glucose between 3 a.m. and 7 a.m. did not differ during Night 1 but fell in Night 2. However, EGP measured with [6-(3)H]glucose at 7 a.m. was higher than that measured with [6,6-(2)H(2)]glucose during both nights, thereby suggesting tracer recycling probably underestimating EGP calculated at 7 a.m. with [6,6-(2)H(2)]glucose. Likewise, EGP was higher at 7 a.m. with [6-(3)H]glucose than at 3 a.m. with [6,6-(2)H(2)]glucose during both nights. The data demonstrate a consistent overnight rise in glucose concentrations through increased EGP, mediated likely by rising cortisol concentrations. The observations with the dual tracer approach imply significant tracer recycling leading to underestimation of EGP measured by longer-duration tracer infusion.

  20. Evaluation Study of VTAE Wood Technics Programs.

    Science.gov (United States)

    Wisconsin State Board of Vocational, Technical, and Adult Education, Madison.

    A survey of former students of the Wisconsin Vocational, Technical, and Adult Education (VTAE) wood technics programs and employers in woodworking industries was conducted during spring of 1985. General objectives were to determine job classifications, types of businesses, and relative importance of tasks or duties in various woodworking-related…

  1. Wood preservatives : choosing the right one

    Science.gov (United States)

    Matt Humphries; Stan Lebow; David Moses

    2009-01-01

    If you are having trouble choosing the right wood preservative system for your application, you are not alone. Dozens of products are available, some older types have gone out of use, others may be completely inappropriate for your application. As designers, specifiers and builders, you need to understand key information to be able to navigate through all of these...

  2. Preparation of wood for energy use

    Science.gov (United States)

    Donald L. Sirois; Bryce J. Stokes

    1985-01-01

    This paper presents an overview & current sources and forms of raw materials for wood energy use and the types of machines available to convert them to the desired form for boiler fuel. Both the fuel source or raw material, and the combustion furnace will dictate the requirements for the processing system. Because of the wide range of processing equipment...

  3. Air quality and composite wood products

    Science.gov (United States)

    Melissa G. D. Baumann

    1999-01-01

    Research at the USDA Forest Service, Forest Products Laboratory (FPL) is being conducted to identify the compounds emitted from wood products during their manufacture and subsequent use. The FPL researchers are measuring the types and quantities of VOCs that are emitted from particleboard and MDF products to provide quantitative emissions information. This information...

  4. Flagella-generated forces reveal gear-type motor in single cells of the green alga, Chlamydomonas reinhardtii.

    Science.gov (United States)

    D'Souza, Jacinta S; Gudipati, Mohanram; Dharmadhikari, Jayashree A; Dharmadhikari, Aditya K; Kashyap, Abhishek; Sivaramakrishnan, Manaswini; Aiyer, Manaswini; Rao, Usha; Mathur, Deepak; Rao, Basuthkar J

    2009-03-06

    Optically trapped single cells of the biflagellated, green alga, Chlamydomonas reinhardtii, rotate. The rotational dynamics of trapped wild-type and mutant cells show that functional flagella play a decisive role: the entire flagellar apparatus (central microtubules, radial spokes, and dynein arms) is involved. Any aberration in this apparatus leads to non-functionality, indicating a gear-type mechanism. The translational and rotational motions of the wild-type and mutant cells do not differ significantly. Optical forces alone do not play a vital role in the rotational dynamics of this cellular motor, making them useful as probes of the internal dynamics without external influence.

  5. Wood fuel and the environment

    International Nuclear Information System (INIS)

    Foster, C.A.

    1992-01-01

    The purpose of this paper is to try and demonstrate the role that the use of Wood as a Fuel can play in our environment. The term ''Wood Fuel'', for the purposes of these proceedings, refers to the use of wood obtained from the forest or the farm. It does not refer to waste wood from for example buildings. The role of wood fuel in the environment can be assessed at many different levels. In this paper three different scales of ''Environment'' and the role of wood fuel in each, will be considered. These three scales are namely the global environment, the local environment, and the National (community) environment. (Author)

  6. Somatosensory neuron types identified by high-coverage single-cell RNA-sequencing and functional heterogeneity

    Science.gov (United States)

    Li, Chang-Lin; Li, Kai-Cheng; Wu, Dan; Chen, Yan; Luo, Hao; Zhao, Jing-Rong; Wang, Sa-Shuang; Sun, Ming-Ming; Lu, Ying-Jin; Zhong, Yan-Qing; Hu, Xu-Ye; Hou, Rui; Zhou, Bei-Bei; Bao, Lan; Xiao, Hua-Sheng; Zhang, Xu

    2016-01-01

    Sensory neurons are distinguished by distinct signaling networks and receptive characteristics. Thus, sensory neuron types can be defined by linking transcriptome-based neuron typing with the sensory phenotypes. Here we classify somatosensory neurons of the mouse dorsal root ganglion (DRG) by high-coverage single-cell RNA-sequencing (10 950 ± 1 218 genes per neuron) and neuron size-based hierarchical clustering. Moreover, single DRG neurons responding to cutaneous stimuli are recorded using an in vivo whole-cell patch clamp technique and classified by neuron-type genetic markers. Small diameter DRG neurons are classified into one type of low-threshold mechanoreceptor and five types of mechanoheat nociceptors (MHNs). Each of the MHN types is further categorized into two subtypes. Large DRG neurons are categorized into four types, including neurexophilin 1-expressing MHNs and mechanical nociceptors (MNs) expressing BAI1-associated protein 2-like 1 (Baiap2l1). Mechanoreceptors expressing trafficking protein particle complex 3-like and Baiap2l1-marked MNs are subdivided into two subtypes each. These results provide a new system for cataloging somatosensory neurons and their transcriptome databases. PMID:26691752

  7. Climate effects of wood used for bioenergy

    Energy Technology Data Exchange (ETDEWEB)

    Ros, Jan P.M.; Van Minnen, Jelle G. [Netherlands Environmental Assessment Agency PBL, Bilthoven (Netherlands); Arets, Eric J.M.M. [Alterra, Wageningen University WUR, Wageningen (Netherlands)

    2013-08-15

    Wood growth and natural decay both take time, and this is an important aspect of sustainability assessments of wood used for energy. Wood taken from forests is a carbon-neutral energy source in the long term, but there are many examples of potential sources of wood used for bioenergy for which net emission reductions are not achieved in 10 to 40 years - the time frame for most climate policy mitigation targets. This is caused by two factors. The first factor relates to the fact that the carbon cycles of wood have a long time span. After final felling, CO2 fixation rates are initially relatively low, but increase again as forests regrow. This regrowth takes many years, sometimes more than a century. Wood residues can either be used or left in the forest. By using them, the emissions from the otherwise decaying residues (taking 2 to 30 years) would be avoided. The second factor concerns the fact that, if the wood is used for bioenergy, then fossil energy emissions are being avoided. However, the direct emission levels from bioenergy are higher than those related to the fossil energy it replaces. These additional emissions also have to be compensated. The carbon debt caused by both factors has to be paid back first, before actual emission reductions can be realised. For wood residues (from harvesting or thinning) that are used to replace coal or oil products, these payback times are relatively short, of the order of 5 to 25 years, mainly depending on location and type of residue (longer if they replace gas). This is also the case when using wood from salvage logging. In most cases, when using wood from final felling directly for energy production, payback times could be many decades to more than a century, with substantial increases in net CO2 emissions, in the meantime. This is especially the case for many forests in Europe, because they are currently an effective carbon sink. Additional felling reduces average growth rates in these forests and thus the sequestration

  8. wood burns down

    Directory of Open Access Journals (Sweden)

    Vladimir Bukh

    2004-11-01

    Full Text Available To relax the local authorities and to receive the guests of high rank «with no tie» the so-called «Fisherman's House» was built at the source of Angara-river, near Lake Baikal. Vladimir Ivanov, a young architect, was noticed by his skillful performa nee of exclusive orders and became the author of this house. At the time of ferroconcrete boom the proposal to build a wooden guest house turned out to be unexpectedly to the point and was graciously approved. The economic department was entrusted to select the men good for carpenter's work, and the forestry department was entrusted to provide thick round timber. And the work started. But, as it usually happens, the workers did not take the trouble and made the first eight rims of the current timber with an inappropriate diameter.And when Pavlov insisted on demolishing the construction and replacing the logs by the logs with the necessary diameter, the building work obeyed to his will and was finished suecessfully.The architecture of the house is not the derived action of the saw and the fret-saw. It is a technology of the axe. It is natural, convincing and original. It is no use to look for the local sources in it. It grew up in the area of timber and cold winter. And this clear and efficient action kept the construction from the annoying vulgarity and provided Siberian exotics easily penetrating into one's soul, refined as it may be.One of the eminent guests said with admiration: «Even if Pavlov had created nothing more, he would have justified his professional choice with this single house.» Why not to say it as a good toast. However, this is a suitable case to add: style is an absence of style. It is a taste.After the Fisherman's House Irkutsk architects were attracted by wood. They followed the strictness in wood and, as much as they could, created a couple of successful remakes, until the cylinder logs and ... new

  9. Low-NO{sub x}, wood chip combustion

    Energy Technology Data Exchange (ETDEWEB)

    Saastamoinen, J.; Oravainen, H.; Haemaelaeinen, J.; Paakkinen, K. [VTT Energy, Jyvaeskylae (Finland)

    1997-10-01

    The regulations for nitrogen oxide emissions vary in different countries, but the general trend in the future will probably be that the emissions limits will be lowered also for wood combustion plants, which are small or medium size units. Thus, the development of wood chip burning furnaces (grate furnaces, fluidized bed combustors, stoker furnaces) with lower nitrogen oxide emissions, is important. The wood used in the combustor, its particle size, moisture and fuel properties (nitrogen content) affect the nitrogen emissions. The nitrogen oxide release is also much affected by the design and operation of the combustor (air staging, fuel air preheat, flue gas circulation, air to fuel mass ratio). The fate of nitrogen compounds originally in the virgin wood depends much on the design of the combustor system and by proper planning it is possible to reduce the emission of nitrogen oxides. Basic knowledge of the release of nitrogen compounds from single wood particles is attained. The release of gaseous nitrogen compounds from wood particles during pyrolysis and combustion is studied experimentally and by modelling. Nitrogen release is studied experimentally by two ways, by analysing the gas and by quenching the particle and analysing the char residue. Formation of nitrogen oxide emissions in a fuel bed is studied by modelling and by combustion experiments with a pot furnace. This research gives general information of nitrogen oxide formation in wood bunting especially in fixed beds. The development of a horizontal stoker burner for wood chips with low emissions is the practical aim of the research. (orig.)

  10. Targeting the Immunogenetic Diseases with the Appropriate HLA Molecular Typing: Critical Appraisal on 2666 Patients Typed in One Single Centre

    Directory of Open Access Journals (Sweden)

    M. Guarene

    2013-01-01

    Full Text Available We compared the immunogenetic data from 2666 patients affected by HLA-related autoimmune diseases with those from 4389 ethnically matched controls (3157 cord blood donors CBD, 1232 adult bone marrow donors BMD, to verify the appropriateness of HLA typing requests received in the past decade. The frequency of HLA-B*27 phenotype was 10.50% in 724 ankylosing spondylitis, 16.80% in 125 uveitis (3.41% BMD, 4.24% CBD, P<0.0001; HLA-B*51 allele was 15.57% in 212 Behçet’s disease (12.91% BMD, 9.88% CBD, P<0.0001; the HLA-DRB1-rheumatoid arthritis (RA shared epitope was 13.72% in 554 RA (10.85% BMD, 13.48% CBD, P=0.016; the carriers of almost one of HLA-DQB1 susceptibility alleles were 84.91% in 795 celiac disease (CD and 59.37% in 256 insulin-dependent diabetes mellitus (IDDM (46.06% in 875 CBD, 42.75% in 662 BMD P<0.0001. Overall, our results show that the HLA marker frequencies were higher in patients than controls, but lower than expected from the literature data (excluding CD and IDDM and demonstrate that, in complex immunogenetic conditions, a substantial number of genetic analyses are redundant and inappropriate, burdening to the public health costs. For this reason, we suggest the Italian Scientific Society of Immunogenetics to establish guidelines to improve the appropriateness of typing requests.

  11. Turning wood residues into wood revenues

    International Nuclear Information System (INIS)

    Graham, R.G.; Kravetz, Don

    1996-01-01

    Ensyn is a profitable commercial company which derives its revenues from the conversion of wood residues into liquid biofuel and chemicals. The technology, Rapid Thermal Processing (RTP (TM) )is based on extremely fast ''cracking'' of biomass which results in light liquid yields exceeding 70% by weight, from wood. Whether producing chemicals or liquid biofuel, the RTP plant is configured identically and operated essentially in the same mode. Chemicals production simply allows economical production to occur at a lower plant capacity, as low as 2 tonnes/day, than is feasible for a dedicated fuel plant (typically greater than 100 tonnes/day). Ensyn has developed the commercialisation of RTP TM from bench to industrial scale in 10 years. A variety of crative funding initiatives in the early years allowed for capital to be raised for R and D without the loss of intellectual property (IP). The transition years of technology demonstration, prior to full commercialisation, were funded by a blend of revenues from venture capital and public sources, and by quickly tapping into a niche market for RTP TM . The utilisation of the technology at the niche market scale opened the doors to the larger fuel and commodity markets. Once, again, both IP and control of the company were maintained during these years. Flexibility, creativity and expertise are necessary to understand the significance of various financing options (private investments, commercial banking and bond issues) and to integrate these options with various renewable energy, recycling and tax incentives. Understanding these options with various renewable energy, recycling and tax incentives is necessary. Understanding both the core and peripheral needs of the customer are essential in successfully advancing a commercial wood energy venture. Ensyn's experience in these areas is the focus of the paper. (Author)

  12. Energy from wood - an overview; Holzenergie, Uebersicht - Energie du bois, apercu du bois

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T. [Verenum, Zuerich (Switzerland)

    2000-07-01

    The present publication is the introduction to a series of papers on fundamentals and applications of wood energy. It summarizes figures and data of the actual situation of fuel wood utilization in Switzerland and its potential for the future. Further, the advantages of bio-energy are discussed and the possibilities of funding for bio-energy in Switzerland are described. Wood contributes with 2.5% to the total energy demand in Switzerland nowadays. However, the utilization of wood energy can be more than doubled, which is one of the targets of the Swiss energy policy. The supply chains for the different types of fuel wood are described and specifications and prices of log wood, forestry wood chips and wood residues are presented. The main applications of wood energy are residential heating with manually operated wood boilers and stoves, on the one hand, and heat production with automatic wood furnaces in industry and communities, on the other hand. Automatic furnaces have been promoted in the past ten years and hence they contribute nowadays with more than 50% to the energy supply from wood with a further growing share. As an assistance for further information, a list of institutions and addresses in the field of wood energy in Switzerland is given in the paper. (author)

  13. Environmental issues: New techniques for managing and using wood fuel ash

    Energy Technology Data Exchange (ETDEWEB)

    Fehrs, J.E.; Donovan, C.T. [C.T. Donovan Associates, Inc., Burlington, VT (United States)

    1993-12-31

    Continued research and development of environmentally-acceptable and cost-effective end uses for wood ash is having a significant affect on the ability to use wood and wood waste for fuel. This is particularly true for ash resulting from treated wood combustion. Concerns about the contents of ash from wood containing paint, stain, preservatives, or other chemicals is one of the largest regulatory barriers to its use as fuel. The purpose of this paper is to: (1) Identify the physical and chemical characteristics of ashes produced from the combustion of untreated and treated wood; (2) Explain the types of {open_quotes}clean, untreated{close_quotes} and {open_quotes}treated{close_quotes} wood that are likely to produce ash that can beneficially used; (3) Describe existing and potential products and end uses for untreated and treated wood ash.

  14. Effect of thermal modification on the physical properties of juvenile and mature woods of Eucalyptus grandis

    Directory of Open Access Journals (Sweden)

    Fred Willians Calonego

    Full Text Available This study aimed to evaluate the effect of thermal treatment on the physical properties of juvenile and mature woods of Eucalyptus grandis. Boards were taken from 30-year-old E. grandis trees. The boards were thermally modified at 180 °C in the Laboratory of Wood Drying and Preservation at UNESP, Botucatu, Sao Paulo state, Brazil. The results showed that thermal modification caused: (1 decrease of 6.8% in the density at 0% equilibrium moisture content of mature wood; (2 significant decreases of 14.7% and 35.6% in the maximum volumetric swellings of juvenile and mature woods, respectively; (3 significant decreases of 13.7% and 21.3% in the equilibrium moisture content of juvenile and mature woods, respectively. The influence of thermal modification in juvenile wood was lower than in mature wood and caused greater uniformity in the physical variations between these types of wood in E. grandis.

  15. The changing market for wood materials used in farm structures.

    Science.gov (United States)

    David C. Baumgartner

    1971-01-01

    This reports describes the number, type, and size of farm structures built in a 17-state area during the years 1963-1965, together with information relating to the use and marketing of wood materials in such structures.

  16. Precision wood particle feedstocks

    Science.gov (United States)

    Dooley, James H; Lanning, David N

    2013-07-30

    Wood particles having fibers aligned in a grain, wherein: the wood particles are characterized by a length dimension (L) aligned substantially parallel to the grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) normal to W and L; the L.times.H dimensions define two side surfaces characterized by substantially intact longitudinally arrayed fibers; the W.times.H dimensions define two cross-grain end surfaces characterized individually as aligned either normal to the grain or oblique to the grain; the L.times.W dimensions define two substantially parallel top and bottom surfaces; and, a majority of the W.times.H surfaces in the mixture of wood particles have end checking.

  17. Ormosioxylon chinjiensis sp. nov., a new fossil wood of family Fabaceae from the Chinji formation Salt Range Punjab, Pakistan

    International Nuclear Information System (INIS)

    Soomro, N.; Arain, B. A.; Rajput, T. M.; Tahir, S. S.

    2016-01-01

    The present work deals with anatomical study of fossil wood collected from the Chinji formation (72 degree 22 min E, 32 degree 4 min N) of Miocene age exposed at the Chinji National Reserve at salt Range Punjab, Pakistan. The material consisted of a single piece of petrified wood. Taxonomical characters of the fossil wood were compared with modern and fossil wood. The sample wood was found comparable to the family Fabaceae. The closest resemblance of the fossil wood was with the wood of Ormosia. The fossil wood under investigation showed close resemblance of vessels, fibers, parenchyma and xylem rays, with the genus Ormosia but shows differences from already reported species of this genus. Hence it is described as a new species as Ormosioxylon chinjiensis sp. nov. The specific epithet refers to Chinji Formation from which the fossil wood is collected. (author)

  18. Wood-pastures of Europe

    DEFF Research Database (Denmark)

    Plieninger, Tobias; Hartel, Tibor; Martín-López, Berta

    2015-01-01

    Wood-pastures are archetypes of High Nature Value Farmlands in Europe and hold exceptional ecological, social, and cultural values. Yet, wood-pastures have been through a sharp decline all over Europe, mainly due to processes of agricultural intensification and abandonment. Recently, wood......-pastures have found increasing attention from conservation science and policy across Europe. In this paper we (i) perform the first pan-European assessment of wood-pastures, considering individual countries and biogeographic regions, (ii) present the ecological and social-cultural values of a wide diversity...... of wood-pasture systems in Europe, (iii) outline management challenges around wood-pastures, and (iv) provide insights for the policy agenda targeting wood-pastures in Europe. We estimate that wood-pastures cover an area of approximately 203,000km2 in the European Union (EU...

  19. Variation in root wood anatomy

    NARCIS (Netherlands)

    Cutler, D.F.

    1976-01-01

    Variability in the anatomy of root wood of selected specimens particularly Fraxinus excelsior L. and Acer pseudoplatanus L. in the Kew reference microscope slide collection is discussed in relation to generalised statements in the literature on root wood anatomy.

  20. Methane from wood

    International Nuclear Information System (INIS)

    Schulz, T. F.; Barreto, L.; Kypreos, S.; Stucki, S.

    2005-07-01

    The role of wood-based energy technologies in the Swiss energy system in the long-term is examined using the energy-system Swiss MARKAL model. The Swiss MARKAL model is a 'bottom-up' energy-systems optimization model that allows a detailed representation of energy technologies. The model has been developed as a joint effort between the Energy Economics Group (EEG) at Paul Scherrer Institute PSI) and the University of Geneva and is currently used at PSI-EEG. Using the Swiss MARKAL model, this study examines the conditions under which wood-based energy technologies could play a role in the Swiss energy system, the most attractive pathways for their use and the policy measures that could support them. Given the involvement of PSI in the ECOGAS project, especial emphasis is put on the production of bio-SNG from wood via gasification and methanation of syngas and on hydrothermal gasification of woody biomass. Of specific interest as weIl is the fraction of fuel used in passenger cars that could be produced by locally harvested wood. The report is organized as follows: Section 2 presents a brief description of the MARKAL model. Section 3 describes the results of the base case scenario, which represents a plausible, 'middle-of-the-road' development of the Swiss energy system. Section 4 discusses results illustrating the conditions under which the wood-based methanation technology could become competitive in the Swiss energy market, the role of oil and gas prices, subsidies to methanation technologies and the introduction of a competing technology, namely the wood-based Fischer-Tropsch synthesis. FinaIly, section 5 outlines some conclusions from this analysis. (author)

  1. Common-Ground-Type Tansformerless Inverters for Single-Phase Solar Photovoltaic Systems

    DEFF Research Database (Denmark)

    Siwakoti, Yam Prasad; Blaabjerg, Frede

    2018-01-01

    This paper proposes a family of novel flying capacitor transformerless inverters for single-phase photovoltaic (PV) systems. Each of the new topologies proposed is based on a flying capacitor principle and requires only four power switches and/or diodes, one capacitor, and a small filter at the o......This paper proposes a family of novel flying capacitor transformerless inverters for single-phase photovoltaic (PV) systems. Each of the new topologies proposed is based on a flying capacitor principle and requires only four power switches and/or diodes, one capacitor, and a small filter...

  2. Compressive Fatigue in Wood

    DEFF Research Database (Denmark)

    Clorius, Christian Odin; Pedersen, Martin Bo Uhre; Hoffmeyer, Preben

    1999-01-01

    An investigation of fatigue failure in wood subjected to load cycles in compression parallel to grain is presented. Small clear specimens of spruce are taken to failure in square wave formed fatigue loading at a stress excitation level corresponding to 80% of the short term strength. Four...... frequencies ranging from 0.01 Hz to 10 Hz are used. The number of cycles to failure is found to be a poor measure of the fatigue performance of wood. Creep, maximum strain, stiffness and work are monitored throughout the fatigue tests. Accumulated creep is suggested identified with damage and a correlation...

  3. TCP HolyWood

    OpenAIRE

    Oscar Núñez Mori

    2005-01-01

    We introduce a new end-to-end, sender side Transport Control Protocol called TCP HolyWood or in short TCP-HW. In a simulated wired environment, TCP HolyWood outperforms in average throughput, three of the more important TCP protocols ever made, we are talking about TCP Reno, TCP Westwood, and TCP Vegas; and in average jitter to TCP Reno and TCP Vegas too. In addition, according to Jain’s index, our proposal is as fair as TCP Reno, the Standard. Apresentamos um novo Protocolo de Controle de...

  4. A revised multi-Fickian moisture transport model to describe non-Fickian effects in wood

    DEFF Research Database (Denmark)

    Frandsen, Henrik Lund; Damkilde, Lars; Svensson, Staffan

    2007-01-01

    This paper presents a study and a refinement of the sorption rate model in a so-called multi-Fickian or multi-phase model. This type of model describes the complex moisture transport system in wood, which consists of separate water vapor and bound-water diffusion interacting through sorption...... sorption allow a simplification of the system to be modeled by a single Fickian diffusion equation. To determine the response of the system, the sorption rate model is essential. Here the function modeling the moisture-dependent adsorption rate is investigated based on existing experiments on thin wood...... conditions for the model are discussed, since discrepancies from corresponding models of moisture transport in paper products have been found. ©2007 by Walter de Gruyter....

  5. A Revised Multi-Fickian Moisture Transport Model To Describe Non-Fickian Effects In Wood

    DEFF Research Database (Denmark)

    Frandsen, Henrik Lund; Svensson, Staffan; Damkilde, Lars

    2007-01-01

    This paper presents a study and a refinement of the sorption rate model in a so-called multi-Fickian or multiphase model. This type of model describes the complex moisture transport system in wood, which consists of separate water vapor and bound-water diffusion interacting through sorption...... sorption allow a simplification of the system to be modeled by a single Fickian diffusion equation. To determine the response of the system, the sorption rate model is essential. Here the function modeling the moisture-dependent adsorption rate is investigated based on existing experiments on thin wood...... conditions for the model are discussed, since discrepancies from corresponding models of moisture transport in paper products have been found....

  6. Type-II second-harmonic-generation properties of YCOB and GdCOB single crystals.

    Science.gov (United States)

    Liu, Yanqing; Qi, Hongwei; Lu, Qingming; Yu, Fapeng; Wang, Zhengping; Xu, Xinguang; Zhao, Xian

    2015-02-09

    As excellent nonlinear optical (NLO) crystals, YCa(4)O(BO(3))(3) (YCOB) and GdCa(4)O(BO(3))(3) (GdCOB) have been paid much attention since their first appearance in 1990's. From that time to now, almost all of related researches and applications have focused on their type-I phase-matching (PM) configurations which possess large effective NLO coefficient (d(eff)). In this paper, type-II second-harmonic-generation (SHG) properties of these two crystals are reported, including PM curve, d(eff), angular acceptance and walk-off angle. Both of the type-II SHG experiments for 1064 and 1320 nm have indicated that the optimum directions which have maximum d(eff) locate in the second octant, i.e. (90° crystal, the largest type-II SHG conversion efficiency of a 1064 nm Nd:YAG pico-second laser is 55%, which reaches the same level of the optimum type-I sample. To our knowledge this is the first time that type-II SHG performance of YCOB and GdCOB crystals is investigated intensively. Our research has shown that the smaller d(eff) of type-II PM can be compensated by its larger angular acceptance and less beam walk-off. The same level SHG conversion efficiency implies for such type crystals the type-II components have the potential to replace type-I ones and obtain important NLO applications in the future.

  7. The Asian Wood Pellet Markets

    Science.gov (United States)

    Joseph A. Roos; Allen Brackley

    2012-01-01

    This study examines the three major wood pellet markets in Asia: China, Japan, and South Korea. In contrast to the United States, where most wood pellets are used for residential heating with pellet stoves, a majority of the wood pellets in Asia are used for co-firing at coal-fired power plants. Our analysis indicated that Japan is the largest importer of wood pellets...

  8. Wood chip production system making its debut in Austria

    Energy Technology Data Exchange (ETDEWEB)

    1987-05-21

    The main component of the wood chip production system is a high-performance drum-type wood chipper which feeds the wood to a blower pipe transferring it to a tiltable chip container. Another essential element consists in the feeding system which continuously feeds the chipper with felled wood and other remains and provides for an uninterrupted, speedy and time-saving charging of the chipping unit. A hydraulic crane serves to feed the chipper. Both the feeding process and the chopping process are controlled by the driver. Wood chipper standard equipment moreover comprises built-in overload safety elements, an automatic stopping device responding as the system gets blocked up, a return circuit clearing the mouth of the feeder in case it is blocked, hydraulically controlled feeding and pressing rollers and an automatic speed controlling device. All components are mounted on a support which is installed on a carrier vehicle.

  9. RNA extraction from decaying wood for (meta)transcriptomic analyses.

    Science.gov (United States)

    Adamo, Martino; Voyron, Samuele; Girlanda, Mariangela; Marmeisse, Roland

    2017-10-01

    Wood decomposition is a key step of the terrestrial carbon cycle and is of economic importance. It is essentially a microbiological process performed by fungi and to an unknown extent by bacteria. To gain access to the genes expressed by the diverse microbial communities participating in wood decay, we developed an RNA extraction protocol from this recalcitrant material rich in polysaccharides and phenolic compounds. This protocol was implemented on 22 wood samples representing as many tree species from 11 plant families in the Angiosperms and Gymnosperms. RNA was successfully extracted from all samples and converted into cDNAs from which were amplified both fungal and bacterial protein coding genes, including genes encoding hydrolytic enzymes participating in lignocellulose hydrolysis. This protocol applicable to a wide range of decomposing wood types represents a first step towards a metatranscriptomic analysis of wood degradation under natural conditions.

  10. Single microwave-photon detector using an artificial Λ-type three-level system

    Science.gov (United States)

    Inomata, Kunihiro; Lin, Zhirong; Koshino, Kazuki; Oliver, William D.; Tsai, Jaw-Shen; Yamamoto, Tsuyoshi; Nakamura, Yasunobu

    2016-07-01

    Single-photon detection is a requisite technique in quantum-optics experiments in both the optical and the microwave domains. However, the energy of microwave quanta are four to five orders of magnitude less than their optical counterpart, making the efficient detection of single microwave photons extremely challenging. Here we demonstrate the detection of a single microwave photon propagating through a waveguide. The detector is implemented with an impedance-matched artificial Λ system comprising the dressed states of a driven superconducting qubit coupled to a microwave resonator. Each signal photon deterministically induces a Raman transition in the Λ system and excites the qubit. The subsequent dispersive readout of the qubit produces a discrete `click'. We attain a high single-photon-detection efficiency of 0.66+/-0.06 with a low dark-count probability of 0.014+/-0.001 and a reset time of ~400 ns. This detector can be exploited for various applications in quantum sensing, quantum communication and quantum information processing.

  11. Classroom Demonstrations of Wood Properties.

    Science.gov (United States)

    Foulger, A. N.

    Presented in this manual are 20 activities selected to show some of the properties of wood and how these properties relate to the cellular structure of wood. Each activity includes stated objectives, indicates materials needed, and explains procedures. Illustrations related to the activities, glossary of terms, and photographs of wood structure…

  12. Status of wood energy applications

    International Nuclear Information System (INIS)

    Zerbe, J.I.

    1991-01-01

    In this address, the potential of wood and wood residues to supply future energy needs is examined. In addition, the possible environmental impact of the use of wood fuels on global climate change is discussed. Technologies for the development of new fuels are described

  13. Wrong way: Heating with wood

    Energy Technology Data Exchange (ETDEWEB)

    1981-10-01

    Energy experts state that 'Heating with wood is a hobby, at the most'. Of course, one can save oil by heating with wood, but cost calculations shaw that it is a highly uneconomical substitute. On the other hand, wood can be recommended for thermal insulation.

  14. Strength loss in decayed wood

    Science.gov (United States)

    Rebecca E. Ibach; Patricia K. Lebow

    2014-01-01

    Wood is a durable engineering material when used in an appropriate manner, but it is susceptible to biological decay when a log, sawn product, or final product is not stored, handled, or designed properly. Even before the biological decay of wood becomes visually apparent, the decay can cause the wood to become structurally unsound. The progression of decay to that...

  15. Ovalbumin as a Wood Adhesive

    Science.gov (United States)

    Charles R. Frihart; Holly Satori; Zhu Rongxian; Michael J. Birkeland

    2014-01-01

    Use of proteins to bond wood dominated industrial production until the middle of the 20th century (1). The ensuing creation of the plywood and glulam beam industries allowed for more efficient use of wood resources than is possible with solid wood products. Many protein sources have been used as adhesives, including plant (soybean) and animal (blood, fish scales,...

  16. Low root biomass and occurrence of ectomycorrhizal exploration types in inhabited wood ant (Formica polyctena) nests in a temperate spruce forest

    Czech Academy of Sciences Publication Activity Database

    Jílková, Veronika; Vohník, Martin; Dauber, J.; Marten, A.; Šimáčková, H.; Frouz, Jan

    2017-01-01

    Roč. 79, March-April (2017), s. 57-62 ISSN 1164-5563 R&D Projects: GA MŠk LM2015075 Institutional support: RVO:60077344 ; RVO:67985939 Keywords : nutrient hotspots * nutrient cycling * exploration types * phosphorus * moisture * Picea abies Subject RIV: EH - Ecology, Behaviour OBOR OECD: Ecology Impact factor: 2.445, year: 2016

  17. Alternative types of molecule-decorated atomic chains in Au–CO–Au single-molecule junctions

    Directory of Open Access Journals (Sweden)

    Zoltán Balogh

    2015-06-01

    Full Text Available We investigate the formation and evolution of Au–CO single-molecule break junctions. The conductance histogram exhibits two distinct molecular configurations, which are further investigated by a combined statistical analysis. According to conditional histogram and correlation analysis these molecular configurations show strong anticorrelations with each other and with pure Au monoatomic junctions and atomic chains. We identify molecular precursor configurations with somewhat higher conductance, which are formed prior to single-molecule junctions. According to detailed length analysis two distinct types of molecule-affected chain-formation processes are observed, and we compare these results to former theoretical calculations considering bridge- and atop-type molecular configurations where the latter has reduced conductance due to destructive Fano interference.

  18. Moisture supply in Danish single-family houses – the influence of occupant behaviour and type of room

    DEFF Research Database (Denmark)

    Møller, Eva B.; Hansen, Ernst Jan de Place

    2017-01-01

    . The study focuses on the dependency of number and age of occupants, occupants’ time spent in the house, square meters living space, ventilation habits and type of room. Moisture supply depends on the type of room; bathroom, basement and living room have the highest values. None of the other parameters seems......According to ISO 13788, the internal moisture supply in dwellings can be described by humidity classes defined by outdoor temperature, occupancy and ventilation. Hygrothermal measurements in indoor air in 500 Danish single-family houses were made to investigate if this corresponds with reality...

  19. Communities of fungi in decomposed wood of oak and pine

    Directory of Open Access Journals (Sweden)

    Kwaśna Hanna

    2016-09-01

    Full Text Available The abundance and diversity of wood decomposing fungi were investigated by isolating and cultivating filamentous fungi from wood and by detection of fruit bodies of ascomycetous and basidiomycetous fungi. The objective was to study the impact of forest management on fungi in 100-year-old oak and 87-year-old Scots pine forests in Northern Poland. Fungi were found on coarse woody debris of decayed stumps and fallen logs, boughs and branches in each of the three (managed and unmanaged examined stands. In total, 226 species of Oomycota and fungi were recorded. Oak wood was colonized by one species of Oomycota and 141 species of fungi including Zygomycota (19 species, Ascomycota (103 species and Basidiomycota (19 species. Scots pine wood was also colonized by one species of Oomycota and 138 species of fungi including Zygomycota (19 species, Ascomycota (90 species and Basidiomycota (29 species. In the first, second and third stages of decomposition, the oak wood was colonized by 101, 89 and 56 species of fungi respectively and pine wood was colonized by 82, 103 and 47 species respectively. Eighty three of the observed species (37% occurred on both types of wood, while the other species displayed nutritional preferences. A decrease in the number of species with advancing decay indicates the necessity for a continuous supply of dead wood to the forest ecosystem.

  20. Ultrasonic Imaging of Reaction Wood in Standing Trees

    Science.gov (United States)

    Brancheriau, Loic; Saadat-Nia, Mohammad Ali; Gallet, Philippe; Lasaygues, Philippe; Pourtahmasi, Kambiz; Kaftandjian, Valerie

    Wood is an orthotropic material and its properties depend on its age but also depend on environmental growing conditions. An important feature of property alteration is reaction wood formation. Reaction wood forms when part of a tree is subjected to mechanical stress, and helps to bring parts of the plant into an optimal position. This article aims to study the effect of reaction wood on ultrasonic wave propagation using tomographic imaging. The ultrasonic emission was a pulse train of square wave. The peak frequency was 80 kHz. Two logs of poplar and spruce were tested because of the presence of different types of reaction wood (tension wood for poplar and compression wood for spruce). Maps were computed according to the Radon theory and using a filtered back projection algorithm with fan beam geometry. The intrinsic parameters were the slowness (s/m) and attenuation (dB/m at 80 kHz). In addition to ultrasonic tests, X-ray imaging in transmission was used. The ultrasonic maps were analyzed to highlight the differences between normal wood and observed reaction zones. The X-ray images were also compared to ultrasonic maps and the relationships between X-ray attenuation and ultrasonic parameters were discussed.

  1. How deep-sea wood falls sustain chemosynthetic life.

    Directory of Open Access Journals (Sweden)

    Christina Bienhold

    Full Text Available Large organic food falls to the deep sea--such as whale carcasses and wood logs--are known to serve as stepping stones for the dispersal of highly adapted chemosynthetic organisms inhabiting hot vents and cold seeps. Here we investigated the biogeochemical and microbiological processes leading to the development of sulfidic niches by deploying wood colonization experiments at a depth of 1690 m in the Eastern Mediterranean for one year. Wood-boring bivalves of the genus Xylophaga played a key role in the degradation of the wood logs, facilitating the development of anoxic zones and anaerobic microbial processes such as sulfate reduction. Fauna and bacteria associated with the wood included types reported from other deep-sea habitats including chemosynthetic ecosystems, confirming the potential role of large organic food falls as biodiversity hot spots and stepping stones for vent and seep communities. Specific bacterial communities developed on and around the wood falls within one year and were distinct from freshly submerged wood and background sediments. These included sulfate-reducing and cellulolytic bacterial taxa, which are likely to play an important role in the utilization of wood by chemosynthetic life and other deep-sea animals.

  2. How Deep-Sea Wood Falls Sustain Chemosynthetic Life

    Science.gov (United States)

    Bienhold, Christina; Pop Ristova, Petra; Wenzhöfer, Frank; Dittmar, Thorsten; Boetius, Antje

    2013-01-01

    Large organic food falls to the deep sea – such as whale carcasses and wood logs – are known to serve as stepping stones for the dispersal of highly adapted chemosynthetic organisms inhabiting hot vents and cold seeps. Here we investigated the biogeochemical and microbiological processes leading to the development of sulfidic niches by deploying wood colonization experiments at a depth of 1690 m in the Eastern Mediterranean for one year. Wood-boring bivalves of the genus Xylophaga played a key role in the degradation of the wood logs, facilitating the development of anoxic zones and anaerobic microbial processes such as sulfate reduction. Fauna and bacteria associated with the wood included types reported from other deep-sea habitats including chemosynthetic ecosystems, confirming the potential role of large organic food falls as biodiversity hot spots and stepping stones for vent and seep communities. Specific bacterial communities developed on and around the wood falls within one year and were distinct from freshly submerged wood and background sediments. These included sulfate-reducing and cellulolytic bacterial taxa, which are likely to play an important role in the utilization of wood by chemosynthetic life and other deep-sea animals. PMID:23301092

  3. Development and evaluation of one step single tube multiplex RT-PCR for rapid detection and typing of dengue viruses

    OpenAIRE

    Parida Manmohan; Shrivastava Ambuj; Santhosh SR; Dash Paban; Saxena Parag; Rao PV

    2008-01-01

    Abstract Background Dengue is emerging as a major public health concern in many parts of the world. The development of a one-step, single tube, rapid, and multiplex reverse transcription polymerase chain reaction (M-RT-PCR) for simultaneous detection and typing of dengue virus using serotype specific primers during acute phase of illness is reported. Results An optimal assay condition with zero background was established having no cross-reaction with closely related members of flavivirus (Jap...

  4. Study of wood polymer combinations from woods of Kashmir

    International Nuclear Information System (INIS)

    Garg, V.P.; Hari Mohan; Rao, K.N.

    1983-01-01

    This report describes the studies conducted to upgrade inferior woods of Kashmir by the application of radiation polymerization process. The process has brought about improvements in the physical and mechanical properties of wood. Wood polymer composite samples have been studied for their use in flooring, wall panelling, roofing shingles, wood carving and in other decorative items. It has been shown that 10% ethyl silicate, when present along with methyl methacrylate or styrene, considerably improves the impact strength and such wood polymer composite samples do not crack even on nailing. Wood polymer composites have been tested for carving and it has been shown that with 50% polymer content, carving quality is preserved. It has also been shown that surface coated wood is more advantageous for use in roofing shingles. (author)

  5. History of wood machining

    Science.gov (United States)

    Peter Koch

    1967-01-01

    The history of wood machining is closely tied to advanced in metallurgy and power sources. It has been strongly and continuously shaped by prevailing economic forces and the rise and decline of other contemporary industries. This paper sketches a few of the highlights, with emphasis on developments in North America.

  6. Grant Wood: "American Gothic."

    Science.gov (United States)

    Fitzgerald, Diane M.

    1988-01-01

    Presents a lesson plan which exposes students in grades 10-12 to the visual symbols and historical references contained in Grant Wood's "American Gothic." Includes background information on the artist and the painting, instructional strategies, a studio activity, and evaluation criteria. (GEA)

  7. Wood waste in Europe

    Energy Technology Data Exchange (ETDEWEB)

    Matos, O.; Ribeiro, R. [Biomass Centre for Energy - CBE, Miranda do Corvo (Portugal)

    1997-12-31

    The energy policy of the EC, as well as most of member states points to a sizeable increase of energy production based on renewable energy sources, wood, wood residues, agricultural residues, energy crops including SRF, organic sludges, solid residues, etc. Most recent goals indicate a desirable duplication of today`s percentage by 2010. The reasons for this interest, besides diversification of sources, less dependence on imported fuels, use of endogenous resources, expected decrease of fossil fuel reserves, use of available land, additional employment and income for rural communities, etc., are related to important environmental benefits namely in terms of emissions of hot house gases. Wood waste, resulting from forest operations, cleaning, cultural and final cuttings, and from wood based industries, constitute a special important resource by reason of quality and availability. In addition to this they do not require additional land use and the removal is beneficial. In the run-up to the becoming December`s 1997 `Climate Change Summit` in Kioto, there is mounting pressure on companies to plan on carbon cuts. (author) 6 refs., 1 tab.

  8. Chapter 3: Wood Decay

    Science.gov (United States)

    Dan Cullen

    2014-01-01

    A significant portion of global carbon is sequestered in forest systems. Specialized fungi have evolved to efficiently deconstruct woody plant cell walls. These important decay processes generate litter, soil bound humic substances, or carbon dioxide and water. This chapter reviews the enzymology and molecular genetics of wood decay fungi, most of which are members of...

  9. Effect of ligand substitution on the exchange interactions in {Mn12}-type single-molecule magnets

    OpenAIRE

    Boukhvalov, D. W.; Dobrovitski, V. V.; Kögerler, P.; Al-Saqer, M.; Katsnelson, M. I.; Lichtenstein, A. I.; Harmon, B. N.

    2010-01-01

    We investigate how the ligand substitution affects the intra-molecular spin exchange interactions, studying a prototypal family of single-molecule magnets comprising dodecanuclear cluster molecules [Mn12O12(COOR)16]. We identify a simple scheme based on accumulated Pauling electronegativity numbers (a.e.n.) of the carboxylate ligand groups (R). The redistribution of the electron density, controlled by a.e.n. of a ligand, changes the degree of hybridization between 3d electrons of manganese an...

  10. Quantitative Proteomic and Phosphoproteomic Approaches for Deciphering the Signaling Pathway for Tension Wood Formation in Poplar.

    Science.gov (United States)

    Mauriat, Mélanie; Leplé, Jean-Charles; Claverol, Stéphane; Bartholomé, Jérôme; Negroni, Luc; Richet, Nicolas; Lalanne, Céline; Bonneu, Marc; Coutand, Catherine; Plomion, Christophe

    2015-08-07

    Trees adjust their growth following forced changes in orientation to re-establish a vertical position. In angiosperms, this adjustment involves the differential regulation of vascular cambial activity between the lower (opposite wood) and upper (tension wood) sides of the leaning stem. We investigated the molecular mechanisms leading to the formation of differential wood types through a quantitative proteomic and phosphoproteomic analysis on poplar subjected to a gravitropic stimulus. We identified and quantified 675 phosphopeptides, corresponding to 468 phosphoproteins, and 3 763 nonphosphorylated peptides, corresponding to 1 155 proteins, in the differentiating xylem of straight-growing trees (control) and trees subjected to a gravitational stimulus during 8 weeks. About 1% of the peptides were specific to a wood type (straight, opposite, or tension wood). Proteins quantified in more than one type of wood were more numerous: a mixed linear model showed 389 phosphopeptides and 556 proteins to differ in abundance between tension wood and opposite wood. Twenty-one percent of the phosphoproteins identified here were described in their phosphorylated form for the first time. Our analyses revealed remarkable developmental molecular plasticity, with wood type-specific phosphorylation events, and highlighted the involvement of different proteins in the biosynthesis of cell wall components during the formation of the three types of wood.

  11. Melamine–Glyoxal–Glutaraldehyde Wood Panel Adhesives without Formaldehyde

    Directory of Open Access Journals (Sweden)

    Xuedong Xi

    2017-12-01

    Full Text Available (MGG’ resin adhesives for bonding wood panels were prepared by a single step procedure, namely reacting melamine with glyoxal and simultaneously with a much smaller proportion of glutaraldehyde. No formaldehyde was used. The inherent slow hardening of this resin was overcome by the addition of N-methyl-2-pyrrolidone hydrogen sulphate ionic liquid as the adhesive hardener in the glue mix. The plywood strength results obtained were comparable with those obtained with melamine–formaldehyde resins pressed under the same conditions. Matrix assisted laser desorption ionisation time of flight (MALDI ToF and Fourier transform Infrared (FTIR analysis allowed the identification of the main oligomer species obtained and of the different types of linkages formed, as well as to indicate the multifaceted role of the ionic liquid. These resins are proposed as a suitable substitute for equivalent formaldehyde-based resins.

  12. Wood Export and Deposition Dynamics in Mountain Watersheds

    Science.gov (United States)

    Senter, Anne Elizabeth

    conditions and accompanying hydrologic responses. Chapter 2 contains development of new theory in support of the introduction of multiplicative coefficients, categorized by water year type, that were used to predict wood export quantities via utilization of an existing discharge-based theoretical equation. This new theory was the product of continued investigations into watershed-scale factors in search of explanation of observed variation of wood export rates into New Bullards Bar Reservoir. The gap between known variability and the attribution of wood export to one hydrologic relation continues to be a persistent issue, as the hierarchical and stochastic temporal and spatial nature of wood budget components remain difficult to quantify. The development of "watershed processes" coefficients was specifically focused on a generalized, parsimonious approach using water year type categories, with validation exercises supporting the approach. In dry years, predictions more closely represented observed wood export quantities, whereas the previously derived annual peak discharge relation yielded large over-predictions. Additional data are needed to continue development of these watershed-specific coefficients. This new approach to wood export prediction may be beneficial in regulated river systems for planning purposes, and its efficacy could be tested in other watersheds. Chapter 3 presents the results of an investigation into wood deposition mechanisms in a 12.2 km segment of the confined, bedrock-dominated South Yuba River watershed. Inclusion of coarse wood particles in the analyses was essential in recognizing depositional patterns, thus supporting the value of utilizing a wider wood-size range. A near-census data collection effort yielded myriad data, of which topographic wetted width and bed elevation data, developed for an observed 4.5-year flood event, were standardized in 10-m intervals and then univariate and linked values were ordered into landform classifications

  13. Inventory of contaminants in waste wood; Inventering av foeroreningar i returtrae

    Energy Technology Data Exchange (ETDEWEB)

    Jermer, Joeran; Ekvall, Annika; Tullin, Claes [Swedish National Testing and Research Inst., Boraas (Sweden)

    2001-03-01

    problems. Metal objects of zinc, brass and aluminium are considered to be particularly troublesome as they may plug primary air openings. PVC residues may cause considerably higher levels of chlorine in waste wood. Chemical analyses indicate that the distribution in levels of impurities varies a lot between deliveries of waste wood. Difficulties to take representative samples probably contribute to this. The knowledge of the contents of different types of waste wood (surface treated wood, preservative-treated, panels, furniture etc) in the waste wood flow is only fragmentary. Most certainly, surface treated (painted, stained etc) wood constitute the highest proportion. Preservative-treated wood, with the exception of railway sleepers and poles, is estimated to constitute approximately 5% of the waste wood flow in Sweden today and the next 25-30 years. The study has confirmed previous studies that waste wood contains a substantial proportion of fine fraction. 25-40% of the waste wood passed a sieve with a mesh size of 4 mm at screening trials. Chemical analyses indicated that the fine fraction will be the main contributor to contaminants of potassium, chlorine, sodium, zinc and lead. Further studies are suggested to focus on sorting, preparation, classification and quality assurance of waste wood.

  14. A single mutation in Taiwanese H6N1 influenza hemagglutinin switches binding to human-type receptors

    Energy Technology Data Exchange (ETDEWEB)

    de Vries, Robert P.; Tzarum, Netanel; Peng, Wenjie; Thompson, Andrew J.; Ambepitiya Wickramasinghe, Iresha N.; de la Pena, Alba T. Torrents; van Breemen, Marielle J.; Bouwman, Kim M.; Zhu, Xueyong; McBride, Ryan; Yu, Wenli; Sanders, Rogier W.; Verheije, Monique H.; Wilson, Ian A.; Paulson, James C.

    2017-07-10

    In June 2013, the first case of human infection with an avian H6N1 virus was reported in a Taiwanese woman. Although this was a single non-fatal case, the virus continues to circulate in Taiwanese poultry. As with any emerging avian virus that infects humans, there is concern that acquisition of human-type receptor specificity could enable transmission in the human population. Despite mutations in the receptor-binding pocket of the human H6N1 isolate, it has retained avian-type (NeuAcα2-3Gal) receptor specificity. However, we show here that a single nucleotide substitution, resulting in a change from Gly to Asp at position 225 (G225D), completely switches specificity to human-type (NeuAcα2-6Gal) receptors. Significantly, G225D H6 loses binding to chicken trachea epithelium and is now able to bind to human tracheal tissue. Structural analysis reveals that Asp225 directly interacts with the penultimate Gal of the human-type receptor, stabilizing human receptor binding.

  15. Size-controllable DNA nanoribbons assembled from three types of reusable brick single-strand DNA tiles.

    Science.gov (United States)

    Shi, Xiaolong; Chen, Congzhou; Li, Xin; Song, Tao; Chen, Zhihua; Zhang, Zheng; Wang, Yanfeng

    2015-11-21

    Precise control of nanostructure is a significant goal shared by supramolecular chemistry, nanotechnology and materials science. In DNA nanotechnology, methods of constructing desired DNA nanostructures using programmable DNA strands have been studied extensively and have become a promising branch of research, but developing universal and low-cost (in the sense of using fewer types of DNA strands) methods remains a challenge. In this work, we propose a novel approach to assemble size-controllable DNA nanoribbons with three types of reusable brick SSTs (single-stranded DNA tiles), where the control of ribbon size is achieved by regulating the concentration ratio between manipulative strands and packed single-stranded DNA tiles. In our method, three types of brick SSTs are sufficient in assembling DNA nanoribbons of different sizes, which is much less than the number of types of unique tile-programmable assembling strategy, thus achieving a universal and low-cost method. The assembled DNA nanoribbons are observed and analyzed by atomic force microscopy (AFM). Experimental observations strongly suggest the feasibility and reliability of our method.

  16. Study shows colon and rectal tumors constitute a single type of cancer

    Science.gov (United States)

    The pattern of genomic alterations in colon and rectal tissues is the same regardless of anatomic location or origin within the colon or the rectum, leading researchers to conclude that these two cancer types can be grouped as one, according to The Cancer

  17. Demographic and Clinical Characteristics of Type 1 Diabetes Mellitus in Omani Children - Single Center Experience

    Directory of Open Access Journals (Sweden)

    Saif Al-Yaarubi

    2014-03-01

    Full Text Available Objectives: To describe the demographic characteristics and clinical presentation of Omani children with type 1 diabetes mellitus at Sultan Qaboos University Hospital, Muscat, Oman. Methods: A retrospective analysis of all children with type 1 diabetes mellitus attending the Pediatric Endocrine Unit at Sultan Qaboos University Hospital, Oman from June 2006 to May 2013. Results: One hundred and forty-four patients were included in the study. The mean±SD of age at diagnosis was 6.7 ± 3.7 years. The median duration of symptoms was 10 days (IQR; 5-14. The most commonly reported presenting symptoms were polyuria (94%, polydipsia (82%, and weight loss (59%. Diabetic ketoacidosis at initial presentation was diagnosed in 31% of the patients. Different insulin regimens were prescribed: multiple daily injections in 109 (76% patients, twice daily insulin regimen in 23 (16% patients, and insulin pump therapy in 12 (8% patients. Family history of type 1 diabetes mellitus was present in 31 (22% patients. There were no significant differences in presenting complaints (polyuria, p=0.182; polydipsia, p=0.848, duration of symptoms (p=0.331, reported weight loss (p=0.753, or diabetic ketoacidosis at presentation (p=0.608 between patients with and without family history of type 1 diabetes mellitus. Conclusion: Polyuria, polydipsia and weight loss are the most common presenting symptoms. Family history of type 1 diabetes mellitus is highly prevalent among the studied patients. Diabetic ketoacidosis was found to be less common in Oman compared to other diabetes centers in the Middle East.

  18. Improving assessment of daily energy expenditure by identifying types of physical activity with a single accelerometer.

    Science.gov (United States)

    Bonomi, A G; Plasqui, G; Goris, A H C; Westerterp, K R

    2009-09-01

    Accelerometers are often used to quantify the acceleration of the body in arbitrary units (counts) to measure physical activity (PA) and to estimate energy expenditure. The present study investigated whether the identification of types of PA with one accelerometer could improve the estimation of energy expenditure compared with activity counts. Total energy expenditure (TEE) of 15 subjects was measured with the use of double-labeled water. The physical activity level (PAL) was derived by dividing TEE by sleeping metabolic rate. Simultaneously, PA was measured with one accelerometer. Accelerometer output was processed to calculate activity counts per day (AC(D)) and to determine the daily duration of six types of common activities identified with a classification tree model. A daily metabolic value (MET(D)) was calculated as mean of the MET compendium value of each activity type weighed by the daily duration. TEE was predicted by AC(D) and body weight and by AC(D) and fat-free mass, with a standard error of estimate (SEE) of 1.47 MJ/day, and 1.2 MJ/day, respectively. The replacement in these models of AC(D) with MET(D) increased the explained variation in TEE by 9%, decreasing SEE by 0.14 MJ/day and 0.18 MJ/day, respectively. The correlation between PAL and MET(D) (R(2) = 51%) was higher than that between PAL and AC(D) (R(2) = 46%). We conclude that identification of activity types combined with MET intensity values improves the assessment of energy expenditure compared with activity counts. Future studies could develop models to objectively assess activity type and intensity to further increase accuracy of the energy expenditure estimation.

  19. Optimal strategy for a single-qubit gate and the trade-off between opposite types of decoherence

    Science.gov (United States)

    Alicki, Robert; Horodecki, Michał; Horodecki, Paweł; Horodecki, Ryszard; Jacak, Lucjan; Machnikowski, Paweł

    2004-07-01

    We study reliable quantum-information processing (QIP) under two different types of environment. The first type is Markovian exponential decay, and the appropriate elementary strategy of protection of qubit is to apply fast gates. The second one is strongly non-Markovian and occurs solely during operations on the qubit. The best strategy is then to work with slow gates. If the two types are both present, one has to optimize the speed of gate. We show that such a trade-off is present for a single-qubit operation in a semiconductor quantum dot implementation of QIP, where recombination of exciton (qubit) is Markovian, while phonon dressing gives rise to the non-Markovian contribution.

  20. Optimal strategy for a single-qubit gate and the trade-off between opposite types of decoherence

    International Nuclear Information System (INIS)

    We study reliable quantum-information processing (QIP) under two different types of environment. The first type is Markovian exponential decay, and the appropriate elementary strategy of protection of qubit is to apply fast gates. The second one is strongly non-Markovian and occurs solely during operations on the qubit. The best strategy is then to work with slow gates. If the two types are both present, one has to optimize the speed of gate. We show that such a trade-off is present for a single-qubit operation in a semiconductor quantum dot implementation of QIP, where recombination of exciton (qubit) is Markovian, while phonon dressing gives rise to the non-Markovian contribution

  1. Single-Particle Tracking of Human Immunodeficiency Virus Type 1 Productive Entry into Human Primary Macrophages.

    Science.gov (United States)

    Li, Qin; Li, Wei; Yin, Wen; Guo, Jia; Zhang, Zhi-Ping; Zeng, Dejun; Zhang, Xiaowei; Wu, Yuntao; Zhang, Xian-En; Cui, Zongqiang

    2017-04-25

    Macrophages are one of the major targets of human immunodeficiency virus (HIV-1), but the viral entry pathway remains poorly understood in these cells. Noninvasive virus labeling and single-virus tracking are effective tools for studying virus entry. Here, we constructed a quantum dot (QD)-encapsulated infectious HIV-1 particle to track viral entry at a single-particle level in live human primary macrophages. QDs were encapsulated in HIV-1 virions by incorporating viral accessory protein Vpr-conjugated QDs during virus assembly. With the HIV-1 particles encapsulating QDs, we monitored the early phase of viral infection in real time and observed that, during infection, HIV-1 was endocytosed in a clathrin-mediated manner; the particles were translocated into Rab5A-positive endosomes, and the core was released into the cytoplasm by viral envelope-mediated endosomal fusion. Drug inhibition assays verified that endosome fusion contributes to HIV-1 productive infection in primary macrophages. Additionally, we observed that a dynamic actin cytoskeleton is critical for HIV-1 entry and intracellular migration in primary macrophages. HIV-1 dynamics and infection could be blocked by multiple different actin inhibitors. Our study revealed a productive entry pathway in macrophages that requires both endosomal function and actin dynamics, which may assist in the development of inhibitors to block the HIV entry in macrophages.

  2. Insertion sequence element single nucleotide polymorphism typing provides insights into the population structure and evolution of Mycobacterium ulcerans across Africa.

    Science.gov (United States)

    Vandelannoote, Koen; Jordaens, Kurt; Bomans, Pieter; Leirs, Herwig; Durnez, Lies; Affolabi, Dissou; Sopoh, Ghislain; Aguiar, Julia; Phanzu, Delphin Mavinga; Kibadi, Kapay; Eyangoh, Sara; Manou, Louis Bayonne; Phillips, Richard Odame; Adjei, Ohene; Ablordey, Anthony; Rigouts, Leen; Portaels, Françoise; Eddyani, Miriam; de Jong, Bouke C

    2014-02-01

    Buruli ulcer is an indolent, slowly progressing necrotizing disease of the skin caused by infection with Mycobacterium ulcerans. In the present study, we applied a redesigned technique to a vast panel of M. ulcerans disease isolates and clinical samples originating from multiple African disease foci in order to (i) gain fundamental insights into the population structure and evolutionary history of the pathogen and (ii) disentangle the phylogeographic relationships within the genetically conserved cluster of African M. ulcerans. Our analyses identified 23 different African insertion sequence element single nucleotide polymorphism (ISE-SNP) types that dominate in different areas where Buruli ulcer is endemic. These ISE-SNP types appear to be the initial stages of clonal diversification from a common, possibly ancestral ISE-SNP type. ISE-SNP types were found unevenly distributed over the greater West African hydrological drainage basins. Our findings suggest that geographical barriers bordering the basins to some extent prevented bacterial gene flow between basins and that this resulted in independent focal transmission clusters associated with the hydrological drainage areas. Different phylogenetic methods yielded two well-supported sister clades within the African ISE-SNP types. The ISE-SNP types from the "pan-African clade" were found to be widespread throughout Africa, while the ISE-SNP types of the "Gabonese/Cameroonian clade" were much rarer and found in a more restricted area, which suggested that the latter clade evolved more recently. Additionally, the Gabonese/Cameroonian clade was found to form a strongly supported monophyletic group with Papua New Guinean ISE-SNP type 8, which is unrelated to other Southeast Asian ISE-SNP types.

  3. Nondiabetic kidney disease in type 2 diabetic patients: A single center experience

    Science.gov (United States)

    Das, U.; Dakshinamurty, K. V.; Prayaga, A.; Uppin, M. S.

    2012-01-01

    Nondiabetic renal disease (NDRD) is seen as a cause of proteinuria and renal failure in type 2 diabetes mellitus (DM). The clinical differences between NDRD and diabetic glomerulosclerosis (DGS) are not clear. This study was done to find the spectrum of NDRD in type 2 DM patients and differences in clinical profile between NDRD and DGS patients. Data of patients with type 2 DM who underwent renal biopsy in this institute from 1990 to 2008 were analyzed retrospectively. Patients were categorized as isolated NDRD, NDRD with DGS, and isolated DGS. A total of 75 patients were included. Mean age was 45 ± 10.2 years, male to female ratio was 3.1 : 1, median duration of DM was 12 months (range, 1 year-15 years), proteinuria was 4.2 ± 3.4 g/day, and serum creatinine was 4.3 ± 3.9 mg/dl. Hypertension was observed in 63 (84%) cases and microscopic hematuria in 24 (32%) cases. Nephrotic syndrome (38.7%) was the commonest clinical presentation. Forty-eight (64%) cases had NDRD and 27 (36%) had DGS. The commonest NDRD was minimal change disease (12.5%). Three (6.3%) patients had lupus nephritis. Tubulointerstitial nephritis has been observed in 10.4% patients. No significant differences between NDRD and DGS patients were found except hypertension which was significantly high in the DGS group. Acute kidney injury and nephritic syndrome were not observed in the DGS group. In conclusion, the incidence of biopsy-proven NDRD in type 2 DM in this study was high. Kidney biopsy aided in the detection of NDRD in clinically suspected patients. PMID:23326046

  4. Characterization of wood-based molding bonded with citric acid

    OpenAIRE

    Umemura, Kenji; Ueda, Tomohide; Kawai, Shuichi

    2012-01-01

    The wood-based moldings were fabricated by using only citric acid as an adhesive. The mechanical properties, water resistances, thermal properties and chemical structure were investigated. Wood powder obtained from Acacia mangium was mixed with citric acid under certain weight ratios (0-40 wt%), and each powder mixture was molded using two types of metal molds at 200 °C and 4MPa for 10 min. The modulus of rupture (MOR) and the modulus of elasticity (MOE) values of the wood-based molding conta...

  5. Preparation of microfibers from wood/ionic liquid solutions.

    Science.gov (United States)

    Polaskova, Martina; Cermak, Roman; Verney, Vincent; Ponizil, Petr; Commereuc, Sophie; Gomes, Margarida F Costa; Padua, Agilio A H; Mokrejs, Pavel; Machovsky, Michal

    2013-01-30

    Two types of ionic liquids, 1-ethyl-3-methylimidazolim acetate and 1-ethyl-3-methylimidazolium lactate, were employed for the direct processing of pine wood into microfibers. The concentration of 5 wt.% of wood in ionic liquids was rated as the most appropriate for electrospinning. The fibers were electrospun into the collector water bath. The final structure varied from individual microfibers to fiber bundles. It was demonstrated that 1-ethyl-3-methylimidazolium lactate is a powerful solvent and provides the direct transformation of pristine pine wood into the non-wovens. Copyright © 2012 Elsevier Ltd. All rights reserved.

  6. Masked Visual Analysis: Minimizing Type I Error in Visually Guided Single-Case Design for Communication Disorders.

    Science.gov (United States)

    Byun, Tara McAllister; Hitchcock, Elaine R; Ferron, John

    2017-06-10

    Single-case experimental designs are widely used to study interventions for communication disorders. Traditionally, single-case experiments follow a response-guided approach, where design decisions during the study are based on participants' observed patterns of behavior. However, this approach has been criticized for its high rate of Type I error. In masked visual analysis (MVA), response-guided decisions are made by a researcher who is blinded to participants' identities and treatment assignments. MVA also makes it possible to conduct a hypothesis test assessing the significance of treatment effects. This tutorial describes the principles of MVA, including both how experiments can be set up and how results can be used for hypothesis testing. We then report a case study showing how MVA was deployed in a multiple-baseline across-subjects study investigating treatment for residual errors affecting rhotics. Strengths and weaknesses of MVA are discussed. Given their important role in the evidence base that informs clinical decision making, it is critical for single-case experimental studies to be conducted in a way that allows researchers to draw valid inferences. As a method that can increase the rigor of single-case studies while preserving the benefits of a response-guided approach, MVA warrants expanded attention from researchers in communication disorders.

  7. One Step Clean-Up Method Combined with Single Accelerated Solvent Extraction for Analysis of Polycyclic Aromatic Hydrocarbons and Phenols in Creosote-Treated Woods by Gas Chromatography-Mass Spectrometry

    International Nuclear Information System (INIS)

    Go, Byung Rye; Choi, Hong Seok; Kim, Hai Dong; Kim, Joo Hoon

    2010-01-01

    A primary concern regarding the wide use of creosote is the long-term release of a variety of toxic constituents present within creosote-treated wood into the environment. The constituents of creosote include polycyclic aromatic hydrocarbons (PAHs, ∼85%), phenols (∼10%), and N-, S-, O-heterocyclic compounds (∼5%). Among the constituents, PAHs and phenols are considered as important pollutants because of their toxicity and high contents in creosote. For example, the US Environment Protection Agency (EPA) has defined 16 PAHs and 11 phenols, which are found in high quantities in creosote, as priority pollutants. The main constituents of creosote has been also reported as being carcinogenic to humans. Therefore, it is important to analyze PAHs and phenols in creosote-treated wood for minimizing the risk of human health and environmental contamination. Due to the environmental and health risk concerns, analysis of PAHs and phenols in creosote-treated wood has been performed using classical extraction and clean-up methods

  8. Evaluation of polysaccharides content in fruit bodies and their antimicrobial activity of four Ganoderma lucidum (W Curt.: Fr. P. Karst. strains cultivated on different wood type substrates

    Directory of Open Access Journals (Sweden)

    Krystyna Skalicka-Woźniak

    2012-03-01

    Full Text Available Quantitative determination of polysaccharides in Ganoderma lucidum fruit bodies from different sawdust cultivation substrates and their antibacterial activity was done. Thirty six samples were analyzed. Four strains of Ganoderma lucidum (GL01, GL02, GL03 and GL04 were cultivated on the growth substrates of three different sawdust types: birch (Bo, maple (Kl or alder (Ol amended with wheat bran in three different concentrations: 10, 20 and 30% (w/w. Even though the richest in polysaccharides was GL01 strain, the highest yields of the polysaccharides were determined in GL04Kl3 sample and was 112.82 mg/g of dry weight. The antibacterial activity of polysaccharides was determined in vitro using micro-dilution broth method. The panel of eight reference bacterial strains was used. All the polysaccharide samples tested showed the broad spectrum and the moderate antibacterial activity. Micrococcus luteus ATCC 10240 strain was the most sensitive with MIC (minimal inhibitory concentration = 0.63 − 1.25 mg/mL.

  9. Transcriptomes of major renal collecting duct cell types in mouse identified by single-cell RNA-seq.

    Science.gov (United States)

    Chen, Lihe; Lee, Jae Wook; Chou, Chung-Lin; Nair, Anil V; Battistone, Maria A; Păunescu, Teodor G; Merkulova, Maria; Breton, Sylvie; Verlander, Jill W; Wall, Susan M; Brown, Dennis; Burg, Maurice B; Knepper, Mark A

    2017-11-14

    Prior RNA sequencing (RNA-seq) studies have identified complete transcriptomes for most renal epithelial cell types. The exceptions are the cell types that make up the renal collecting duct, namely intercalated cells (ICs) and principal cells (PCs), which account for only a small fraction of the kidney mass, but play critical physiological roles in the regulation of blood pressure, extracellular fluid volume, and extracellular fluid composition. To enrich these cell types, we used FACS that employed well-established lectin cell surface markers for PCs and type B ICs, as well as a newly identified cell surface marker for type A ICs, c-Kit. Single-cell RNA-seq using the IC- and PC-enriched populations as input enabled identification of complete transcriptomes of A-ICs, B-ICs, and PCs. The data were used to create a freely accessible online gene-expression database for collecting duct cells. This database allowed identification of genes that are selectively expressed in each cell type, including cell-surface receptors, transcription factors, transporters, and secreted proteins. The analysis also identified a small fraction of hybrid cells expressing aquaporin-2 and anion exchanger 1 or pendrin transcripts. In many cases, mRNAs for receptors and their ligands were identified in different cells (e.g., Notch2 chiefly in PCs vs. Jag1 chiefly in ICs), suggesting signaling cross-talk among the three cell types. The identified patterns of gene expression among the three types of collecting duct cells provide a foundation for understanding physiological regulation and pathophysiology in the renal collecting duct.

  10. Diabetes complications in 1952 type 2 diabetes mellitus patients managed in a single institution

    International Nuclear Information System (INIS)

    Alwakeel, Jamal S.; Suliman, R.; Tarif, N.; Al-Suwaida, A.; Hammad, D.; Al-Asaad, H.; Al-Harbi, A.; Al-Mohaya, S.; Alam, A.

    2008-01-01

    Because there is no recent update on the state of diabetes and its concomitant applications in Saudi Arabia, we undertook a study of the prevalence of health complications in patients with type 2 diabetes mellitus admitted to our institution. We conducted a retrospective review of medical results of adult Saudi patients with type 2 diabetes who were seen in clinics or admitted to the Security Forces Hospital, Riyadh, Saudi Arabia, between January 1989 and January 2004. Of 1952, 943 (48.3%) were males. For the whole study population the mean age at enrollment was 58.4+-14.2 years, the mean age at the onset of diabetes was 48.1+-12.8 years, the mean duration of diabetes was 10.4+-7.5 years, and the mean duration of follow-up was 7.9+-4.6 years. Nephropathy was the most prevalent complication, occurring in 626 patients (32.1%). Acute coronary syndrome occurred in 451 (23.1%), cataracts in 447 (22.9$), retinopathy in 326 (16.7%), and myocardial infarction in 279 (14.3%), Doubling of serum ceartinine was seen in 250 (12.8%) and 79 (4.0%) went into dialysis. Hypertension was present in 1524 (78.1%) dyslipidemia in 764 (39.1%). Overall mortality was 8.2%. Multiple complications were frequent. Males had higher prevalence of complications than females (P<.05). Mortality was significantly higher in males 92 (9.8%) than females 69 (6.8%) (P=.024). The prevalence of complications significantly increased with duration of diabetes and age (P<.05). Among Saudis, the prevalence of concomitant diabetic complications is high, with cardiovascular and renal complications the most frequent. Many patients had multiple complications. Early and frequent screening in patients with type 2 diabetes is desirable to identify patients at high risk for concomitant complications and to prevent disabilities. (author)

  11. Radioactivity of Wood and Environment

    International Nuclear Information System (INIS)

    Hus, M.; Kosutic, K.; Lulic, S.

    2003-01-01

    Nuclear experiments in the atmosphere and nuclear accidents caused global deposition of artificial radionuclides in the soil of Earth's northern hemisphere, the territory of the Republic of Croatia included. Soil contamination by radionuclides resulted in their deposition in plants growing on the contaminated soil as well as in the trees. Large area of the Republic of Croatia is covered with wood, which is exploited in manufacture of industrial wood and for firewood. From approximately 3 million cubic metres of wood exploited annually, nearly one third serves for firewood. In the process of burning a smaller portion of radionuclides deposited in the wood evaporates and goes to atmosphere while a larger portion is retained in the ash. In this paper are presented the results of natural radionuclides 4 0K , 2 32T h and 2 38U as well as of artificial radionuclide 1 37C s content determination in the wood, wood briquette, charcoal and in ash remained after burning the wood, wood briquette and charcoal. The obtained results are discussed from wood radiocontamination aspect and from the aspect of potential environmental radiocontamination by the products from wood burning process. (author)

  12. Lignin-Retaining Transparent Wood.

    Science.gov (United States)

    Li, Yuanyuan; Fu, Qiliang; Rojas, Ramiro; Yan, Min; Lawoko, Martin; Berglund, Lars

    2017-09-11

    Optically transparent wood, combining optical and mechanical performance, is an emerging new material for light-transmitting structures in buildings with the aim of reducing energy consumption. One of the main obstacles for transparent wood fabrication is delignification, where around 30 wt % of wood tissue is removed to reduce light absorption and refractive index mismatch. This step is time consuming and not environmentally benign. Moreover, lignin removal weakens the wood structure, limiting the fabrication of large structures. A green and industrially feasible method has now been developed to prepare transparent wood. Up to 80 wt % of lignin is preserved, leading to a stronger wood template compared to the delignified alternative. After polymer infiltration, a high-lignin-content transparent wood with transmittance of 83 %, haze of 75 %, thermal conductivity of 0.23 W mK -1 , and work-tofracture of 1.2 MJ m -3 (a magnitude higher than glass) was obtained. This transparent wood preparation method is efficient and applicable to various wood species. The transparent wood obtained shows potential for application in energy-saving buildings. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

  13. Lump wood combustion process

    Science.gov (United States)

    Kubesa, Petr; Horák, Jiří; Branc, Michal; Krpec, Kamil; Hopan, František; Koloničný, Jan; Ochodek, Tadeáš; Drastichová, Vendula; Martiník, Lubomír; Malcho, Milan

    2014-08-01

    The article deals with the combustion process for lump wood in low-power fireplaces (units to dozens of kW). Such a combustion process is cyclical in its nature, and what combustion facility users are most interested in is the frequency, at which fuel needs to be stoked to the fireplace. The paper defines the basic terms such as burnout curve and burning rate curve, which are closely related to the stocking frequency. The fuel burning rate is directly dependent on the immediate thermal power of the fireplace. This is also related to the temperature achieved in the fireplace, magnitude of flue gas losses and the ability to generate conditions favouring the full burnout of the fuel's combustible component, which, at once ensures the minimum production of combustible pollutants. Another part of the paper describes experiments conducted in traditional fireplaces with a grate, at which well-dried lump wood was combusted.

  14. Fabrication and Characterization of a Single Hole Transistor in p-type GaAs/AlGaAs Heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Tracy, Lisa A [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Reno, John L. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Hargett, Terry W. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    Most spin qubit research to date has focused on manipulating single electron spins in quantum dots. However, hole spins are predicted to have some advantages over electron spins, such as reduced coupling to host semiconductor nuclear spins and the ability to control hole spins electrically using the large spin-orbit interaction. Building on recent advances in fabricating high-mobility 2D hole systems in GaAs/AlGaAs heterostructures at Sandia, we fabricate and characterize single hole transistors in GaAs. We demonstrate p-type double quantum dot devices with few-hole occupation, which could be used to study the physics of individual hole spins and control over coupling between hole spins, looking towards eventual applications in quantum computing. Intentionally left blank

  15. Growth of large size lithium niobate single crystals of high quality by tilting-mirror-type floating zone method

    Energy Technology Data Exchange (ETDEWEB)

    Sarker, Abdur Razzaque, E-mail: razzaque_ru2000@yahoo.com [Department of Physics, University of Rajshahi (Bangladesh)

    2016-05-15

    Large size high quality LiNbO{sub 3} single crystals were grown successfully by tilting-mirror-type floating zone (TMFZ) technique. The grown crystals were characterized by X-ray diffraction, etch pits density measurement, Impedance analysis, Vibrating sample magnetometry (VSM) and UV-Visible spectrometry. The effect of mirror tilting during growth on the structural, electrical, optical properties and defect density of the LiNbO{sub 3} crystals were investigated. It was found that the defect density in the crystals reduced for tilting the mirror in the TMFZ method. The chemical analysis revealed that the grown crystals were of high quality with uniform composition. The single crystals grown by TMFZ method contains no low-angle grain boundaries, indicating that they can be used for high efficiency optoelectronic devices. (author)

  16. Single and multi-subject clustering of flow cytometry data for cell-type identification and anomaly detection.

    Science.gov (United States)

    Pouyan, Maziyar Baran; Jindal, Vasu; Birjandtalab, Javad; Nourani, Mehrdad

    2016-08-10

    Measurement of various markers of single cells using flow cytometry has several biological applications. These applications include improving our understanding of behavior of cellular systems, identifying rare cell populations and personalized medication. A common critical issue in the existing methods is identification of the number of cellular populations which heavily affects the accuracy of results. Furthermore, anomaly detection is crucial in flow cytometry experiments. In this work, we propose a two-stage clustering technique for cell type identification in single subject flow cytometry data and extend it for anomaly detection among multiple subjects. Our experimentation on 42 flow cytometry datasets indicates high performance and accurate clustering (F-measure > 91 %) in identifying main cellular populations. Furthermore, our anomaly detection technique evaluated on Acute Myeloid Leukemia dataset results in only <2 % false positives.

  17. Mechanical properties of wood

    Science.gov (United States)

    David W. Green; Jerrold E. Winandy; David E. Kretschmann

    1999-01-01

    The mechanical properties presented in this chapter were obtained from tests of small pieces of wood termed “clear” and “straight grained” because they did not contain characteristics such as knots, cross grain, checks, and splits. These test pieces did have anatomical characteristics such as growth rings that occurred in consistent patterns within each piece. Clear...

  18. Out of the woods.

    Science.gov (United States)

    Jacobson, J L

    1992-01-01

    Throughout Africa, Asia and Latin America women are pushed out of forests and from their maintenance by governments and private interests for cash crop development disregarding the role of women in conserving forests. In developing countries forests are a source of wood for fuel; 60-80% of women gather wood for family needs in America. Fruits, vegetables, and nuts gathered in woods enhance their diet. Indonesian women pick bananas, mangos, guavas, and avocados from trees around their homes; in Senegal shea-nut butter is made from a local tree fruit to be sold for cash. Women provide labor also in logging, wood processing, and tree nurseries. They make charcoal and grow seedlings for sale. In India 40% of forest income and 75% of forest products export earnings are derived from nonwood resources. Poor, rural women make items out of bamboo, rattan, and rope to sell: 48% of women in an Egyptian province make a living through such activities. In India 600,000 women harvest tendu leaves for use as wrappings for cigarettes. The expansion of commercial tree plantations replacing once communal natural forests has forced poor households to spend up to 4-% of their income on fuel that they used to find in forests. Tribal women in India know the medicinal uses of 300 forest species, and women in Sierra Leone could name 31 products they obtained or made from trees and bushes, while men named only 8 items. Only 1 forestry project appraised by the World Bank during 1984-97 named women as beneficiaries, and only 1 out of 33 rural development programs funded by the World Bank did. Women provide food, fuel, and water for their families in subsistence economies, they know sustainable methods of forestry, yet they are not included in development programs whose success or failure could hinge on more attention to women's contribution and on more equity.

  19. Thermal load histories for North American roof assembles using various cladding materials including wood-thermoplastic composite shingles

    Science.gov (United States)

    J. E. Winandy

    2006-01-01

    Since 1991, thermal load histories for various roof cladding types have been monitored in outdoor attic structures that simulate classic North American light-framed construction. In this paper, the 2005 thermal loads for wood-based composite roof sheathing, wood rafters, and attics under wood-plastic composite shingles are compared to common North American roof...

  20. Preliminary studies of Brazilian wood using different radioisotopic sources

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Gilberto; Silva, Leonardo Gondim de Andrade e, E-mail: gcarval@ipen.br, E-mail: ftgasilva@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2013-07-01

    Due to availability and particular features, wood was one of the first materials used by mankind with a wide variety of applications. It can be used as raw material for paper and cellulose manufacturing; in industries such as chemical, naval, furniture, sports goods, toys, and musical instrument; in building construction and in the distribution of electric energy. Wood has been widely researched; therefore, wood researchers know that several aspects such as temperature, latitude, longitude, altitude, sunlight, soil, and rainfall index interfere with the growth of trees. This behavior explains why average physical-chemical properties are important when wood is studied. The majority of researchers consider density to be the most important wood property because of its straight relationship with the physical and mechanical properties of wood. There are three types of wood density: basic, apparent and green. The apparent density was used here at 12% of moisture content. In this study, four different types of wood were used: 'freijo', 'jequetiba', 'muiracatiara' and 'ipe'. For wood density determination by non-conventional method, Am-241, Ba-133 and Cs-137 radioisotopic sources; a NaI scintillation detector and a counter were used. The results demonstrated this technique to be quick and accurate. By considering the nuclear parameters obtained as half value layers and linear absorption coefficients, Cs-137 radioisotopic source demonstrated to be the best option to be used for inspection of the physical integrity of electric wooden poles and live trees for future works. (author)

  1. Wood fuels utilization in Central Europe - the wood fuels consumption and the targets of utilization

    International Nuclear Information System (INIS)

    Alakangas, E.

    1999-01-01

    Following subjects are discussed in this presentation: The share of bioenergy of the total energy consumption in EU region; the wood fuels consumption in EU region in 1995; the division of bioenergy utilization (households, wood- based district heating, wood consumption in industry, power generation from wood and residues, biofuels, biogas and sludges); wood fuels consumption in households in EU countries in 1995; wood consumption in France; the additional wood fuel consumption potential in France; Blan bois - wood energy program; French wood energy markets; German wood energy markets; energy consumption in Germany; wood consumption in Bavaria; the wood fuels potential in Bavaria; wood fuels consumption in households in Bavaria; wood fuels consumption for district heating in Bavaria; fuel prices in Bavaria; Environmental regulations in Germany; small boiler markets in Germany; Energy consumption in Austria; small-scale utilization of wood fuels; utilization of wood energy. (Slides, additional information from the author)

  2. Wood Fingerprints:Recognition of Sawn Wood Products

    OpenAIRE

    Pahlberg, Tobias

    2014-01-01

    This thesis deals with wood fingerprints and presents ways to track sawn wood products through an industrial process using cameras. The possibility to identify individual wood products comes from the biological variation of the trees, where the genetic code, environment and breakdown process creates a unique appearance for every board. This application has much of the same challenges as are found in human biometrics applications.The vision for the future is to be able to utilize existing imag...

  3. Radiographic testing of wood

    International Nuclear Information System (INIS)

    Osterloh, K.; Zscherpel, U.; Raedel, C.; Weidemann, G.; Meinel, D.; Goebbels, J.; Ewert, U.; Hasenstab, A.; Buecherl, T.

    2007-01-01

    Wood is an old and established consumption and construction material. It is still the most common material for constructing furniture, roofs, playgrounds and mine supports. In contrast to steel and concrete, wood warns of extreme loads by creaking. Its mechanical stability is more influenced by decay than by peripheral cracks. While external cracks are visible, internal decay by fungus growth is undetectable from outside. This may be a safety problem in supporting structures. The best analysis of the internal structure is provided by computed tomography, but this is also the most complex method, much more so than simple radiographic testing. However, the latter is made inaccurate by scattered radiation resulting from internal moisture. With the image processing options of digital radiographic techniques, the structural information can be separated effectively from noise. In contrast to X-ray and gamma radiography, neutron radiography provides information on the spatial distribution of moisture. In healthy wood, water is conducted in the sapwood while the hardwood is dry. Moisture in hardwood is caused by infestations, e.g. fungus growth. The contribution presents a comparative analysis of the available radiographic methods. (orig.)

  4. Variation of power generation at different buffer types and conductivities in single chamber microbial fuel cells

    KAUST Repository

    Nam, Joo-Youn

    2010-01-15

    Microbial fuel cells (MFCs) are operated with solutions containing various chemical species required for the growth of electrochemically active microorganisms including nutrients and vitamins, substrates, and chemical buffers. Many different buffers are used in laboratory media, but the effects of these buffers and their inherent electrolyte conductivities have not been examined relative to current generation in MFCs. We investigated the effect of several common buffers (phosphate, MES, HEPES, and PIPES) on power production in single chambered MFCs compared to a non-buffered control. At the same concentrations the buffers produced different solution conductivities which resulted in different ohmic resistances and power densities. Increasing the solution conductivities to the same values using NaCl produced comparable power densities for all buffers. Very large increases in conductivity resulted in a rapid voltage drop at high current densities. Our results suggest that solution conductivity at a specific pH for each buffer is more important in MFC studies than the buffer itself given relatively constant pH conditions. Based on our analysis of internal resistance and a set neutral pH, phosphate and PIPES are the most useful buffers of those examined here because pH was maintained close to the pKa of the buffer, maximizing the ability of the buffer to contribute to increase current generation at high power densities. © 2009 Elsevier B.V. All rights reserved.

  5. Variation of power generation at different buffer types and conductivities in single chamber microbial fuel cells.

    Science.gov (United States)

    Nam, Joo-Youn; Kim, Hyun-Woo; Lim, Kyeong-Ho; Shin, Hang-Sik; Logan, Bruce E

    2010-01-15

    Microbial fuel cells (MFCs) are operated with solutions containing various chemical species required for the growth of electrochemically active microorganisms including nutrients and vitamins, substrates, and chemical buffers. Many different buffers are used in laboratory media, but the effects of these buffers and their inherent electrolyte conductivities have not been examined relative to current generation in MFCs. We investigated the effect of several common buffers (phosphate, MES, HEPES, and PIPES) on power production in single chambered MFCs compared to a non-buffered control. At the same concentrations the buffers produced different solution conductivities which resulted in different ohmic resistances and power densities. Increasing the solution conductivities to the same values using NaCl produced comparable power densities for all buffers. Very large increases in conductivity resulted in a rapid voltage drop at high current densities. Our results suggest that solution conductivity at a specific pH for each buffer is more important in MFC studies than the buffer itself given relatively constant pH conditions. Based on our analysis of internal resistance and a set neutral pH, phosphate and PIPES are the most useful buffers of those examined here because pH was maintained close to the pK(a) of the buffer, maximizing the ability of the buffer to contribute to increase current generation at high power densities. Copyright 2009 Elsevier B.V. All rights reserved.

  6. Large-scale separation of single-walled carbon nanotubes by electronic type using click chemistry

    Science.gov (United States)

    Um, Jo-Eun; Song, Sun Gu; Yoo, Pil J.; Song, Changsik; Kim, Woo-Jae

    2018-01-01

    Single-walled carbon nanotubes (SWCNTs) can be either metallic or semiconducting, making their separation critical for applications in nanoelectronics, biomedical materials, and solar cells. Herein, we investigate a novel solution-phase separation method based on click chemistry (azide-alkyne Huisgen cycloaddition) and determine its efficiency and scalability. In this method, metallic SWCNTs in metallic/semiconducting SWCNT mixtures are selectively functionalized with alkyne groups by being reacted with 4-propargyloxybenezenediazonium tetrafluoroborate. Subsequently, silica nanoparticles are functionalized with azide groups and reacted with alkyne-bearing metallic SWCNTs in the SWCNT mixture in the presence of a Cu catalyst. As a result, metallic SWCNTs are anchored on silica powder, whereas non-functionalized semiconducting SWCNTs remain in solution. Low-speed centrifugation effectively removes the silica powder with attached metallic SWCNTs, furnishing a solution of highly pure semiconducting SWCNTs, as confirmed by Raman and UV-vis/near-infrared absorption measurements. This novel separation scheme exhibits the advantage of simultaneously separating both metallic and semiconducting SWCNTs from their mixtures, being cost-effective and therefore applicable at an industrial scale.

  7. Evaluating the efficacy of wood shreds for mitigating erosion

    Science.gov (United States)

    Randy B. Foltz; Natalie S. Copeland

    2009-01-01

    An erosion control product made by shredding on-site woody materials was evaluated for mitigating erosion through a series of rainfall simulations. Tests were conducted on bare soil and soil with 30, 50, and 70% cover on a coarse and a fine-grained soil. Results indicated that the wood product known as wood shreds reduced runoff and soil loss from both soil types....

  8. Analysis of Horse Myostatin Gene and Identification of Single Nucleotide Polymorphisms in Breeds of Different Morphological Types

    OpenAIRE

    Dall'Olio, Stefania; Fontanesi, Luca; Nanni Costa, Leonardo; Tassinari, Marco; Minieri, Laura; Falaschini, Adalberto

    2010-01-01

    Myostatin (MSTN) is a negative modulator of muscle mass. We characterized the horse (Equus caballus) MSTN gene and identified and analysed single nucleotide polymorphisms (SNPs) in breeds of different morphological types. Sequencing of coding, untranslated, intronic, and regulatory regions of MSTN gene in 12 horses from 10 breeds revealed seven SNPs: two in the promoter, four in intron 1, and one in intron 2. The SNPs of the promoter (GQ183900:g.26T > C and GQ183900:g.156T > C, the latter loc...

  9. Plutonium (TRU) transmutation and {sup 233}U production by single-fluid type accelerator molten-salt breeder (AMSB)

    Energy Technology Data Exchange (ETDEWEB)

    Furukaw, Kazuo [Tokai Univ., Kanagawa (Japan); Kato, Yoshio [Japan Atom. Ene. Res. Inst., Ibaraki (Japan); Chigrinov, Sergey E. [Academy of Science, Minsk (Belarus)

    1995-10-01

    For practical/industrial disposition of Pu(TRU) by accelerator facility, not only physical soundness and safety but also the following technological rationality should be required: (1) few R&D items including radiation damage, heat removal and material compatibility; (2) few operation/maintenance/processing works: (3) few reproduction of radioactivity; (4) effective energy production in parallel. This will be achieved by the new modification of Th-fertilizing Single-Fluid type Accelerator Molten-Salt Breeder (AMSB), by which a global nuclear energy strategy for next century might be prepared.

  10. Performance of a Horizontal Double Cylinder Type of Fresh Coffee Cherries Pulping Machine

    OpenAIRE

    Widyotomo, Sukrisno; Mulato, Sri; Ahmad, H; Soekarno, s

    2009-01-01

    Pulping is one important step in wet coffee processing method. Usually, pulping process uses a machine which constructed using wood or metal materials. A horizontal single cylinder type coffee pulping machine is the most popular machine in coffee processor and market. One of the weakness of a horizontal single cylinder type coffee pulping machine is high of broken beans. Broken beans is one of major aspect in defect system that result in low quality. Indonesian Coffee and Cocoa Research Insti...

  11. Development of a single multi-locus sequence typing scheme for Taylorella equigenitalis and Taylorella asinigenitalis.

    Science.gov (United States)

    Duquesne, Fabien; Hébert, Laurent; Breuil, Marie-France; Matsuda, Motoo; Laugier, Claire; Petry, Sandrine

    2013-12-27

    We describe here the development of a multilocus sequence typing (MLST) scheme for Taylorella equigenitalis, the causative agent of contagious equine metritis (CEM), and Taylorella asinigenitalis, a nonpathogenic bacterium. MLST was performed on a set of 163 strains collected in several countries over 35 years (1977-2012). The MLST data were analyzed using START2, MEGA 5.05 and eBURST, and can be accessed at http://pubmlst.org/taylorella/. Our results revealed a clonal population with 39 sequence types (ST) and no common ST between the two Taylorella species. The eBURST analysis grouped the 27 T. equigenitalis STs into four clonal complexes (CC1-4) and five unlinked STs. The 12 T. asinigenitalis STs were grouped into three clonal complexes (CC5-7) and five unlinked STs, among which CC1 (68.1% of the 113 T. equigenitalis) and CC5 (58.0% of the 50 T. asinigenitalis) were dominants. The CC1, still in circulation in France, contains isolates from the first CEM outbreaks that simultaneously emerged in several countries in the late 1970s. The emergence in different countries (e.g. France, Japan, and United Arab Emirates) of STs without any genetic relationship to CC1 suggests the existence of a natural worldwide reservoir that remains to be identified. T. asinigenitalis appears to behave same way since the American, Swedish and French isolates have unrelated STs. This first Taylorella sp. MLST is a powerful tool for further epidemiological investigations and population biology studies of the Taylorella genus. Copyright © 2013 Elsevier B.V. All rights reserved.

  12. European wood-fuel trade

    International Nuclear Information System (INIS)

    Hillring, B.; Vinterbaeck, J.

    2001-01-01

    This paper discusses research carried out during the l990s on European wood fuel trade at the Department of Forest Management and Products, SLU, in Sweden. Utilisation of wood-fuels and other biofuels increased very rapidly in some regions during that period. Biofuels are replacing fossil fuels which is an effective way to reduce the future influence of green house gases on the climate. The results indicate a rapid increase in wood-fuel trade in Europe from low levels and with a limited number of countries involved. The chief products traded are wood pellets, wood chips and recycled wood. The main trading countries are, for export, Germany and the Baltic states and, for import, Sweden, Denmark and to some extent the Netherlands. In the future, the increased use of biofuel in European countries is expected to intensify activity in this trade. (orig.)

  13. Wegner estimate and localization for alloy-type models with sign-changing exponentially decaying single-site potentials

    Science.gov (United States)

    Leonhardt, Karsten; Peyerimhoff, Norbert; Tautenhahn, Martin; Veselić, Ivan

    2015-05-01

    We study Schrödinger operators on L2(ℝd) and ℓ2(ℤd) with a random potential of alloy-type. The single-site potential is assumed to be exponentially decaying but not necessarily of fixed sign. In the continuum setting, we require a generalized step-function shape. Wegner estimates are bounds on the average number of eigenvalues in an energy interval of finite box restrictions of these types of operators. In the described situation, a Wegner estimate, which is polynomial in the volume of the box and linear in the size of the energy interval, holds. We apply the established Wegner estimate as an ingredient for a localization proof via multiscale analysis.

  14. Proton Pumping and Slippage Dynamics of a Eukaryotic P-Type ATPase Studied at the Single-Molecule Level

    DEFF Research Database (Denmark)

    Veshaguri, Salome

    In all eukaryotes the plasma membrane potential and secondary transport systems are energized by P-type ATPases whose regulation however remains poorly understood. Here we monitored at the single-molecule level the activity of the prototypic proton pumping P-type ATPase Arabidopsis thaliana isoform...... pumping rates remained constant. Titration of ATP down to ~1% of apparent Km for ATPase activity exclusively affected the distributions of the durations the pump spends in active and inactive states. The dramatic consequence of our findings is that ATP reduction decreased ATP/H+ stoichiometry of the pump....... We propose that variable ATP/H+ stoichiometry emerges as a novel mechanism for adaptation when challenged with depletion of ATP that is likely relevant for other ATPases. Such measurements will provide indispensable insights into the mechanisms of function and regulation of many other ion...

  15. Factors affecting sodium hypochlorite extraction of CCA from treated wood.

    Science.gov (United States)

    Gezer, E D; Cooper, P A

    2009-12-01

    Significant amounts of chromated copper arsenate (CCA) treated wood products, such as utility poles and residential construction wood, remain in service. There is increasing public concern about environmental contamination from CCA-treated wood when it is removed from service for reuse or recycling, placed in landfills or burned in commercial incinerators. In this paper, we investigated the effects of time, temperature and sodium hypochlorite concentration on chromium oxidation and extraction of chromated copper arsenate from CCA-treated wood (Type C) removed from service. Of the conditions evaluated, reaction of milled wood with sodium hypochlorite for one hour at room temperature followed by heating at 75 degrees C for two hours gave the highest extraction efficiency. An average of 95% Cr, 99% Cu and 96% As could be removed from CCA-treated, milled wood by this process. Most of the extracted chromium was oxidized to the hexavalent state and could therefore be recycled in a CCA treating solution. Sodium hypochlorite extracting solutions could be reused several times to extract CCA components from additional treated wood samples.

  16. World trade in forest products and wood fuel

    International Nuclear Information System (INIS)

    Hillring, Bengt

    2006-01-01

    Wood fuel is a strategic resource for future energy supply and is usually utilised locally. Traditional use of wood fuel and other bioenergy has a share of 10-15% energy supply, used mainly for the household sector. The utilisation for industrial purposes is much smaller but is a strategic resource in the effort to fulfil the Kyoto agreement to replace fossil fuels and to mitigate greenhouse gas emissions. Many industrialised countries already use a significant share of biofuels in their energy supply e.g. Nordic countries while others like some other European Union countries are planning to increase their use. Production and use of biofuels need to be carried out sustainable. Official statistics do not report trade in such detail that international trade in different biomass types can be fully identified. However, FAO and European Forestry Institute are important sources. In some countries, there is a growing interest in the international trade, because the trade can provide biofuels at lower prices, larger quantities and better quality than domestic alternatives. The first signs of an international market price for wood fuel are indicated in Europe. For the future both the use and the trade of wood fuel is expected to increase. Analyses for trade in charcoal, wood chips, fuel wood and wood residues made in this report identify 'hot' trade spots in Europe, in south East Asia and in North America

  17. Single assay for simultaneous detection and differential identification of human and avian influenza virus types, subtypes, and emergent variants.

    Directory of Open Access Journals (Sweden)

    David Metzgar

    Full Text Available For more than four decades the cause of most type A influenza virus infections of humans has been attributed to only two viral subtypes, A/H1N1 or A/H3N2. In contrast, avian and other vertebrate species are a reservoir of type A influenza virus genome diversity, hosting strains representing at least 120 of 144 combinations of 16 viral hemagglutinin and 9 viral neuraminidase subtypes. Viral genome segment reassortments and mutations emerging within this reservoir may spawn new influenza virus strains as imminent epidemic or pandemic threats to human health and poultry production. Traditional methods to detect and differentiate influenza virus subtypes are either time-consuming and labor-intensive (culture-based or remarkably insensitive (antibody-based. Molecular diagnostic assays based upon reverse transcriptase-polymerase chain reaction (RT-PCR have short assay cycle time, and high analytical sensitivity and specificity. However, none of these diagnostic tests determine viral gene nucleotide sequences to distinguish strains and variants of a detected pathogen from one specimen to the next. Decision-quality, strain- and variant-specific pathogen gene sequence information may be critical for public health, infection control, surveillance, epidemiology, or medical/veterinary treatment planning. The Resequencing Pathogen Microarray (RPM-Flu is a robust, highly multiplexed and target gene sequencing-based alternative to both traditional culture- or biomarker-based diagnostic tests. RPM-Flu is a single, simultaneous differential diagnostic assay for all subtype combinations of type A influenza viruses and for 30 other viral and bacterial pathogens that may cause influenza-like illness. These other pathogen targets of RPM-Flu may co-infect and compound the morbidity and/or mortality of patients with influenza. The informative specificity of a single RPM-Flu test represents specimen-specific viral gene sequences as determinants of virus type, A

  18. Elevated serum triglycerides is the strongest single indicator for the presence of metabolic syndrome in patients with type 2 diabetes

    Directory of Open Access Journals (Sweden)

    Dimou Eleni

    2006-10-01

    Full Text Available Abstract Background Patients with diabetes already fulfill one diagnostic criterion for MS according to the existing classifications. Our aim was to identify one single clinical parameter, which could effectively predict the presence of MS in patients with type 2 diabetes. Methods We studied all patients with type 2 diabetes who attended our Diabetes Outpatient Clinic during a three-month period. Waist circumference, blood pressure and serum lipids were measured. Establishment of MS diagnosis was based a on National Cholesterol Education Program Adult Treatment Panel III (NCEP ATP III criteria and b on International Diabetes Federation (IDF criteria. Receiver operating characteristic (ROC analysis was applied in order to identify the clinical parameter with the highest predictive capability for MS. Among the 500 participating patients (231 males, 269 females, MS was diagnosed in 364 patients (72.8% according to the NCEP ATP III criteria and in 408 patients (81.6% according to the IDF criteria. Results For the NCEP ATP III classification, serum triglycerides (in the overall population, waist and HDL (in female population demonstrated the highest predictive capability for MS (AUCs:0.786, 0.805 and 0.801, respectively. For the IDF classification, no single parameter reached an AUC > 0.800 in the overall population. In females, HDL displayed a satisfactory predictive capability for MS with an AUC which was significantly higher than the one in males (0.785 vs. 0.676, respectively, p Conclusion Elevated serum triglycerides strongly indicate the presence of MS in patients with type 2 diabetes. In female patients with type 2 diabetes, central obesity was the second stronger predictor of MS besides hypertriglyceridemia.

  19. A single dose of sodium nitrate does not improve oral glucose tolerance in patients with type 2 diabetes mellitus.

    Science.gov (United States)

    Cermak, Naomi M; Hansen, Dominique; Kouw, Imre W K; van Dijk, Jan-Willem; Blackwell, Jamie R; Jones, Andrew M; Gibala, Martin J; van Loon, Luc J C

    2015-08-01

    Dietary nitrate (NO3(-)) supplementation has been proposed as an emerging treatment strategy for type 2 diabetes. We hypothesized that ingestion of a single bolus of dietary NO3(-) ingestion improves oral glucose tolerance in patients with type 2 diabetes. Seventeen men with type 2 diabetes (glycated hemoglobin, 7.3% ± 0.2%) participated in a randomized crossover experiment. The subjects ingested a glucose beverage 2.5 hours after consumption of either sodium NO3(-) (0.15 mmol NaNO3(-) · kg(-1)) or a placebo solution. Venous blood samples were collected before ingestion of the glucose beverage and every 30 minutes thereafter during a 2-hour period to assess postprandial plasma glucose and insulin concentrations. The results show that plasma NO3(-) and nitrite levels were increased after NaNO3(-) as opposed to placebo ingestion (treatment-effect, P = .001). Despite the elevated plasma NO3(-) and nitrite levels, ingestion of NaNO3(-) did not attenuate the postprandial rise in plasma glucose and insulin concentrations (time × treatment interaction, P = .41 for glucose, P = .93 for insulin). Despite the lack of effect on oral glucose tolerance, basal plasma glucose concentrations measured 2.5 hours after NaNO3(-) ingestion were lower when compared with the placebo treatment (7.5 ± 0.4 vs 8.3 ± 0.4 mmol/L, respectively; P = .04). We conclude that ingestion of a single dose of dietary NO3(-) does not improve subsequent oral glucose tolerance in patients with type 2 diabetes. Copyright © 2015 Elsevier Inc. All rights reserved.

  20. ESTIMATION OF THE SCALE PARAMETER FROM THE RAYLEIGH DISTRIBUTION FROM TYPE II SINGLY AND DOUBLY CENSORED DATA

    Directory of Open Access Journals (Sweden)

    Ahmad Saeed Akhter

    2009-01-01

    Full Text Available As common as the normal distribution is the Rayleigh distribution which occurs in works on radar, properties of sine wave plus-noise, etc. Rayleigh (1880 derived it from the amplitude of sound resulting from many important sources. The Rayleigh distribution is widely used in communication engineering, reliability analysis and applied statistics. Since the Rayleigh distribution has linearly increasing rate, it is appropriate for components which might not have manufacturing defects but age rapidly with time. Several types of electro-vacum devices have this feature. It is connected with one dimension and two dimensions random walk and is some times referred to as a random walk frequency distribution. It is a special case of Weibull distribution (1951 of wide applicability. It can be easily derived from the bivariate normal distribution with and p = 0. For further application of Rayleigh distribution, we refer to Johnson and Kotz (1994. Adatia (1995 has obtained the best linear unbiased estimator of the Rayleigh scale parameter based on fairly large censored samples. Dyer and Whisend (1973 obtained the BLUE of scale parameter based on type II censored samples for small N = 2(15. With the advance of computer technology it is now possible to obtain BLUE for large samples. Hirai (1978 obtained the estimate of the scale parameter from the Rayleigh distribution singly type II censored from the left side and right side and variances of the scale parameter. In this paper, we estimate the scale parameter of type II singly and doubly censored data from the Rayleigh distribution using Blom’s (1958 unbiased nearly best estimates and compare the efficiency of this estimate with BLUE and MLE.

  1. Induction of specific neuron types by overexpression of single transcription factors.

    Science.gov (United States)

    Teratani-Ota, Yusuke; Yamamizu, Kohei; Piao, Yulan; Sharova, Lioudmila; Amano, Misa; Yu, Hong; Schlessinger, David; Ko, Minoru S H; Sharov, Alexei A

    2016-10-01

    Specific neuronal types derived from embryonic stem cells (ESCs) can facilitate mechanistic studies and potentially aid in regenerative medicine. Existing induction methods, however, mostly rely on the effects of the combined action of multiple added growth factors, which generally tend to result in mixed populations of neurons. Here, we report that overexpression of specific transcription factors (TFs) in ESCs can rather guide the differentiation of ESCs towards specific neuron lineages. Analysis of data on gene expression changes 2 d after induction of each of 185 TFs implicated candidate TFs for further ESC differentiation studies. Induction of 23 TFs (out of 49 TFs tested) for 6 d facilitated neural differentiation of ESCs as inferred from increased proportion of cells with neural progenitor marker PSA-NCAM. We identified early activation of the Notch signaling pathway as a common feature of most potent inducers of neural differentiation. The majority of neuron-like cells generated by induction of Ascl1, Smad7, Nr2f1, Dlx2, Dlx4, Nr2f2, Barhl2, and Lhx1 were GABA-positive and expressed other markers of GABAergic neurons. In the same way, we identified Lmx1a and Nr4a2 as inducers for neurons bearing dopaminergic markers and Isl1, Fezf2, and St18 for cholinergic motor neurons. A time-course experiment with induction of Ascl1 showed early upregulation of most neural-specific messenger RNA (mRNA) and microRNAs (miRNAs). Sets of Ascl1-induced mRNAs and miRNAs were enriched in Ascl1 targets. In further studies, enrichment of cells obtained with the induction of Ascl1, Smad7, and Nr2f1 using microbeads resulted in essentially pure population of neuron-like cells with expression profiles similar to neural tissues and expressed markers of GABAergic neurons. In summary, this study indicates that induction of transcription factors is a promising approach to generate cultures that show the transcription profiles characteristic of specific neural cell types.

  2. Knowledge, attitude and performance of wood painter about harmful effects of solvents and dyes on human health

    Directory of Open Access Journals (Sweden)

    Mohammad Miri

    2014-11-01

    Full Text Available Background: Solvents, which are widely used in industry, are able to dissolve another substance for creating a solution. Solvents have various effects on human health based on their type and chemical composition. Methods: This was a cross-sectional study to investigate the harmful effects of solvents on wood painters in Yazd city. To achieve information, a census questionnaire was prepared and distributed among wood painters. The studied parameters include the mean score of knowledge, attitude, and practice of wood painters about harmful effects of dyes and solvents on body according to age, work experience, education, hours worked per day, and smoking. The data of survey were analyzed by Chi-square test and T-test in SPSS. Results: The average age and work experience of wood painters were 29 and 7.5 years, and the age of 25 years and work experience of 5 years had the highest frequency among them. Analysis of data indicated that 71.8% of people had middle school and lower education level, 68.3% was married, 31.7% was single, and 37.5% was smoking. Average working hours were 8 hours in day. Conclusion: Results show that attitudes had significant correlation with education level and different age groups. None of the studied parameters were not significant correlation with performance. Also, there was significant correlation between knowledge with experience.

  3. The Effect of Carbon Nanotubes on the Mechanical Properties of Wood Plastic Composites by Selective Laser Sintering

    Directory of Open Access Journals (Sweden)

    Yunhe Zhang

    2017-12-01

    Full Text Available Wood-plastic composites (WPCs made by selective laser sintering (SLS approach of 3D printing offer many advantages over single polymer materials, such as low cost, sustainability, and better sintering accuracy. However, WPCs made via SLS are too weak to have widespread applications. In order to increase the mechanical properties of WPCs, a novel type of WPCs containing 0, 0.05, 0.1 and 0.15 wt % carbon nanotubes (CNT, 14 wt % wood fibers, 86 wt % polyether sulfone (PES was manufactured via SLS. The experimental results showed that the addition of small amount of CNTs can significantly increase the mechanical properties of the wood/PES composite material. The tensile strength, bending strength, and elasticity modulus were 76.3%, 227.9%, and 128.7% higher with 0.1 wt % CNTs than those without CNTs. The mechanical properties of specimens first increased and then decreased with the addition of CNTs. The SEM results of the specimens’ fracture morphology indicate that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons why the composites possessed superior mechanical properties: CNTs facilitate the laser sintering process of WPCs due to their thermal conductivities, and CNTs directly reinforce WPCs.

  4. Controlling mold on wood Pallets

    Science.gov (United States)

    Carol A. Clausen

    2012-01-01

    THE WOOD PALLET AND CONTAINER INDUSTRY CONSUMES 4.5 billion board feet (BBF) of hardwoods and 1.8 BBF of softwoods for the annual production of 400-500 million solid wood pallets. While alternative materials such as plastic, corrugated paperboard and metal have entered the market, solid wood remains the material of choice for a majority of pallets on the market (more...

  5. Impacts of traditional architecture on the use of wood as an element of facade covering in Serbian contemporary architecture

    Directory of Open Access Journals (Sweden)

    Ivanović-Šekularac Jelena

    2011-01-01

    Full Text Available The world trend of re-use of wood and wood products as materials for construction and covering of architectural structures is present not only because of the need to meet the aesthetic, artistic and formal requirements or to seek inspiration in the return to the tradition and nature, but also because of its ecological, economic and energetic feasibility. Furthermore, the use of wood fits into contemporary trends of sustainable development and application of modern technical and technological solutions in the production of materials, in order to maintain a connection to nature, environment and tradition. In this study the author focuses on wood and wood products as an element of facade covering on buildings in our country, in order to extend knowledge about possibilities and limitations of their use and create a base for their greater and correct application. The subject of this research is to examine the application of wood and wood products as an element covering the exterior in combination with other materials applied in our traditional and contemporary homes with the emphasis on functional, representational art and the various possibilities of wood. In this study all the factors that affect the application of wood and wood products have been analyzed and the conclusions have been drawn about the manner of their implementation and the types of wood and wood products protection. The development of modern technological solutions in wood processing led to the production of composite materials based on wood that are highly resistant, stable and much longer lasting than wood. Those materials have maintained in an aesthetic sense all the characteristics of wood that make it unique and inimitable. This is why modern facade coating based on wood should be applied as a facade covering in the exterior of modern architectural buildings in Serbia, and the use wood reduced to a minimum.

  6. Modal analysis and dispersion curves of an elliptical W-type single mode fiber

    Science.gov (United States)

    Prajapati, Y.; Maurya, Jitendra Bahadur; Singh, Vivek; Saini, J. P.

    2015-05-01

    In this paper, the propagation of electromagnetic waves in W-type elliptical dielectric optical fiber having various cladding layers is presented. The presented fiber has concentric core and cladding which have elliptical cross section and the refractive index of one of the inner cladding (the cladding between first clad and last clad) maximum. Using elliptic cylindrical coordinates, boundary conditions are derived and longitudinal field components for the even and odd modes are obtained. The characteristic equation for the fiber to be studied is determined by solving the Mathieu ( q > 0) and the modified Mathieu functions ( q < 0). In order to study the fundamental mode, the modal index m is put as m = 1. Finally, the cutoff frequencies for several lower order modes have been calculated and their dispersion characteristics are plotted. The effects of elliptical eccentricity e on the mode cutoff frequencies and mode transmissions are also addressed. The analysis shows that one can control the propagation property of optical fiber by increasing the number of inner claddings. These claddings provide additional degree of freedom to control the modes.

  7. Pregnancy outcomes and nutritional indices after 3 types of bariatric surgery performed at a single institution.

    Science.gov (United States)

    Mead, Nancy C; Sakkatos, Panagiotis; Sakellaropoulos, George C; Adonakis, George L; Alexandrides, Theodore K; Kalfarentzos, Fotis

    2014-01-01

    Nutritional status during pregnancy and the effects of nutritional deficiencies on pregnancy outcomes after bariatric surgery is an important issue that warrants further study. The objective of this study was to investigate pregnancy outcomes and nutritional indices after restrictive and malabsorptive procedures. We investigated pregnancy outcomes of 113 women who gave birth to 150 children after biliopancreatic diversion (BPD), Roux-en-Y gastric bypass (RYGB), and sleeve gastrectomy (SG) between June 1994 and December 2011. Biochemical indices and pregnancy outcomes were compared among the different types of surgery and to overall 20-year hospital data, as well as to 56 presurgery pregnancies in 36 women of the same group. Anemia was observed in 24.2% and 15.6% of pregnancies after BPD and RYGB, respectively. Vitamin B12 levels decreased postoperatively in all groups, with no further decrease during pregnancy; however, low levels were observed not only after BPD (11.7%) and RYGB (15.6%), but also after SG (13.3%). Folic acid levels increased. Serum albumin levels decreased in all groups during pregnancy, but hypoproteinemia was seen only after BPD. Neonates after BPD had significantly lower average birth weight without a higher frequency of low birth weight defined asnutritional supplement guidelines are followed. Closer monitoring is required in pregnancies after malabsorptive procedures especially regarding protein nutrition. Copyright © 2014 American Society for Bariatric Surgery. Published by Elsevier Inc. All rights reserved.

  8. Cellulose synthesis in two secondary cell wall processes in a single cell type.

    Science.gov (United States)

    Mendu, Venugopal; Stork, Jozsef; Harris, Darby; DeBolt, Seth

    2011-11-01

    Plant cells have a rigid cell wall that constrains internal turgor pressure yet extends in a regulated and organized manner to allow the cell to acquire shape. The primary load-bearing macromolecule of a plant cell wall is cellulose, which forms crystalline microfibrils that are organized with respect to a cell's function and shape requirements. A primary cell wall is deposited during expansion whereas secondary cell wall is synthesized post expansion during differentiation. A complex form of asymmetrical cellular differentiation occurs in Arabidopsis seed coat epidermal cells, where we have recently shown that two secondary cell wall processes occur that utilize different cellulose synthase (CESA) proteins. One process is to produce pectinaceous mucilage that expands upon hydration and the other is a radial wall thickening that reinforced the epidermal cell structure. Our data illustrate polarized specialization of CESA5 in facilitating mucilage attachment to the parent seed and CESA2, CESA5 and CESA9 in radial cell wall thickening and formation of the columella. Herein, we present a model for the complexity of cellulose biosynthesis in this highly differentiated cell type with further evidence supporting each cellulosic secondary cell wall process.

  9. Inoculation Expedition of Agar wood

    International Nuclear Information System (INIS)

    Peng, C.S.; Mohd Fajri Osman; Rusli Zakaria

    2015-01-01

    Inoculation expedition of agar wood is a main field works for researcher in Nuclear Malaysia to prove the real inoculation of agar wood in real jungle. These expeditions was conducted fourth times in the jungles of Malaysia including Gunung Tebu in Terengganu, Murum in Belaga, Sarawak, Kampung Timbang in Kota Belud, Sabah and Nuclear Malaysia itself. This expedition starts from preparation of samples and equipment, transportation into the jungle, searching and recognition of agar wood and lastly, inoculation of the agar wood. Safety aspects precedence set out in the preparation and implementation of this expedition. (author)

  10. XPS characterization of naturally aged wood

    Energy Technology Data Exchange (ETDEWEB)

    Popescu, Carmen-Mihaela, E-mail: mihapop@icmpp.ro [Romanian Academy, ' P.Poni' Institute of Macromolecular Chemistry, Physical Chemistry of Polymers Laboratory, 41A Gr. Ghica Voda Alley, Ro 700487, Iasi (Romania); Tibirna, Carmen-Mihaela [Centre de Recherche sur le Bois (CRB), Departement des Sciences du Bois et de la Foret, Laval University, Quebec, G1 V 0A6 (Canada); Vasile, Cornelia [Romanian Academy, ' P.Poni' Institute of Macromolecular Chemistry, Physical Chemistry of Polymers Laboratory, 41A Gr. Ghica Voda Alley, Ro 700487, Iasi (Romania)

    2009-12-15

    Wood deterioration over time (by a simultaneously biological, chemical or physical attack) is an inevitable continuous process in the environment. This process destroys all heritage resulting in a loss of valuable old wooden structures and their properties. What type of deterioration occurs and how these processes impact the wood are important questions that need consideration if old wooden structures are to be studied and properly preserved. X-ray photoelectron spectroscopy (XPS) was employed to analyze the undegraded (sound wood of {approx}6 years) and degraded lime wood ({approx}150 years, {approx}180 years, {approx}250 years) from painting supports, differing in terms of the provenance, conservation status and environmental conditions of storage. Elaborated XPS analysis (comparison of C and O individual spectra, decomposition for each atomic component, calculation of O/C ratio) provided a view of the composition of the sample surfaces analyzed. On the basis of these results, it was confirmed that significant changes occurred in the first period of ageing, the {approx}150 years lime wood sample having the highest percent of the carbon atoms and the lowest percentage of oxygen atoms and, respectively O/C ratio. According to our previous studies (X-ray diffraction, FTIR spectroscopy, analytical pyrolysis combined with gas chromatography/mass spectrometry and ESR-spectroscopy results), these features could be attributed to the fact that hemicelluloses and amorphous cellulose are degraded in time, whereas the crystalline fraction of cellulose decreases more slowly than the amorphous one. Consequently, the observation may be made that lignin is not so easily degraded under the environmental conditions where paintings are frequently exposed.

  11. Clinical and molecular characterization of 112 single-center patients with Neurofibromatosis type 1.

    Science.gov (United States)

    Corsello, Giovanni; Antona, Vincenzo; Serra, Gregorio; Zara, Federico; Giambrone, Clara; Lagalla, Luca; Piccione, Maria; Piro, Ettore

    2018-04-04

    The aim of this retrospective study was to define clinical and molecular characteristics of a large sample of neurofibromatosis type 1 (NF1) patients, as well as to evaluate mutational spectrum and genotype-phenotype correlation. NF1 is a relatively common neurogenetic disorder (1:2500-1:3000 individuals). It is caused by mutations of the NF1 gene on chromosome 17ql1.2, with autosomal dominant pattern of inheritance and wide phenotypical variability. Café-au-lait spots (CALs), cutaneous and/or subcutaneous neurofibromas (CNFs/SCNFs), skinfold freckling, skeletal abnormalities, Lisch nodules of the iris and increased risk of learning and intellectual disabilities, as well as tumors of the nervous system and other organs are its main clinical features. The preliminary group collected 168 subjects with clinical suspicion of NF1. They were evaluated following the National Institutes of Health (NIH) criteria for NF1, revised by Gutmann et al. 1997, integrated for 67 of them by molecular testing. According to these references, 112 of 168 patients were diagnosed as NF1. The sample was characterized by an equal sex ratio (57 males, 55 females) and age distribution ranging from 10 days to 60 years of age (mean age, 13 years). A wide spectrum of clinical features has been observed in our patients. Mutational analysis resulted positive in 51 cases (76%). Twenty-four mutations detected in our cohort have not been reported to date. This study may contribute to a better definition of genotypic and phenotypic features of NF1 patients, with respect to further insights into the clinical characterization of the disease. In addition, an amplification of the spectrum of mutations in the NF1 gene has been documented.

  12. Glycogen storage disease type III in Egyptian children: a single centre clinico-laboratory study.

    Science.gov (United States)

    El-Karaksy, Hanaa; Anwar, Ghada; El-Raziky, Mona; Mogahed, Engy; Fateen, Ekram; Gouda, Amr; El-Mougy, Fatma; El-Hennawy, Ahmed

    2014-06-01

    Glycogen storage disease type III (GSD III) is an autosomal recessive disorder caused by deficiency of glycogen debrancher enzyme and is characterised by clinical variability. We herein describe the clinical and laboratory findings in 31 Egyptian patients with GSD III presenting to the Paediatric Hepatology Unit, Cairo University, Egypt. Eighteen patients (58%) were males. Their ages ranged between 6 months to 12 years. The main presenting complaint was progressive abdominal distention in 55%. Twelve patients (38.7%) had a history of recurrent attacks of convulsions; four had an erroneous diagnosis of hypocalcaemia and epilepsy. Doll-like facies was noted in 90%. Abdominal examination of all cases revealed abdominal distention and soft hepatomegaly which had bright echogenicity by ultrasound. Hypertriglyceridaemia was present in 93.6%, hyperlactacidaemia in 51.6% and hyperuricaemia in 19.4%. Liver biopsy showed markedly distended hepatocytes with well distinct cytoplasmic boundaries and 32% had macrovesicular fatty changes. Serum creatine kinase was elevated in 64.6% of patients and correlated positively and significantly with age (r=0.7 and P=<0.001), while serum triglycerides correlated negatively with age (r=-0.4 and P=0.05). Blood glucose assessment and search for hepatomegaly in an infant with recurrent seizures may prevent delay in the diagnosis. A huge soft liver reaching the left midclavicular line that appears echogenic on ultrasonography is characteristic of GSD III. A distended hepatocyte with rarified cytoplasm is pathognomonic but not diagnostic. Hypertriglyceridaemia correlates negatively with age, in contrary to CK level. Copyright © 2014 Arab Journal of Gastroenterology. Published by Elsevier Ltd. All rights reserved.

  13. Sensing interrogation technique for fiber-optic interferometer type of sensors based on a single-passband RF filter.

    Science.gov (United States)

    Chen, Hao; Zhang, Shiwei; Fu, Hongyan; Zhou, Bin; Chen, Nan

    2016-02-08

    In this paper, a sensing interrogation system for fiber-optic interferometer type of sensors by using a single-passband radio-frequency (RF) filter has been proposed and experimentally demonstrated. The fiber-optic interferometer based sensors can give continuous optical sampling, and along with dispersive medium a single-passband RF frequency response can be achieved. The sensing parameter variation on the fiber-optic interferometer type of sensors will affect their free spectrum range, and thus the peak frequency of the RF filter. By tracking the central frequency of the passband the sensing parameter can be demodulated. As a demonstration, in our experiment a fiber Mach-Zehnder interferometer (FMZI) based temperature sensor has been interrogated. By tracking the peak frequency of the passband the temperature variation can be monitored. In our experiment, the sensing responsivity of 10.5 MHz/°C, 20.0 MHz/°C and 41.2 MHz/°C, when the lengths of sensing fiber are 1 m, 2 m and 4 m have been achieved.

  14. Analytical and semi-analytical inverse kinematics of SSRMS-type manipulators with single joint locked failure

    Science.gov (United States)

    Xu, Wenfu; She, Yu; Xu, Yangsheng

    2014-12-01

    Redundant space manipulators, including Space Station Remote Manipulator System (SSRMS), Special Purpose Dexterous Manipulator (SPDM) and European Robotic Arm (ERA), have been playing important roles in the construction and maintenance of International Space Station (ISS). They all have 7 revolute joints arranged in similar configurations, and are referred to as SSRMS-type manipulators. When a joint is locked in an arbitrary position due to some failures, a 7R manipulator degrades to a 6R manipulator. Without a spherical wrist or three consecutive parallel joints, the inverse kinematics of the 6R manipulator is very complex. In this paper, we propose effective methods to resolve the inverse kinematics for different cases of any joint locked in an arbitrary position. Firstly, configuration characteristics of the SSRMS-type redundant manipulators are analyzed. Then, an existing of closed-form inverse kinematics is discussed for locking different joints. Secondly, D-H frames and corresponding D-H parameters of the new 6-DOF manipulator formed by locking a joint in an arbitrary position are re-constructed. A unified table is then created to describe the kinematics for all possible cases of single joint locking failure. Thirdly, completely analytical and semi-analytical methods are presented to solve the inverse kinematics equations, and the former is used for locking joint 1, 2, 6 or 7 while the latter for locking joint 3, 4 or 5. Finally, typical cases for single joint locking are studied. The results verify the proposed methods.

  15. Rheological Characterisation of the Flow Behaviour of Wood Plastic Composites in Consideration of Different Volume Fractions of Wood

    Science.gov (United States)

    Laufer, N.; Hansmann, H.; Koch, M.

    2017-01-01

    In this study, the rheological properties of wood plastic composites (WPC) with different polymeric matrices (LDPE, low-density polyethylene and PP, polypropylene) and with different types of wood filler (hardwood flour and softwood flour) have been investigated by means of high pressure capillary rheometry. The volume fraction of wood was varied between 0 and 60 %. The shear thinning behaviour of the WPC melts can be well described by the Ostwald - de Waele power law relationship. The flow consistency index K of the power law shows a good correlation with the volume fraction of wood. Interparticular interaction effects of wood particles can be mathematically taken into account by implementation of an interaction exponent (defined as the ratio between flow exponent of WPC and flow exponent of polymeric matrix). The interaction exponent shows a good correlation with the flow consistency index. On the basis of these relationships the concept of shear-stress-equivalent inner shear rate has been modified. Thus, the flow behaviour of the investigated wood filled polymer melts could be well described mathematically by the modified concept of shear-stress-equivalent inner shear rate. On this basis, the shear thinning behaviour of WPC can now be estimated with good accuracy, taking into account the volume fraction of wood.

  16. Simultaneous isolation of emm89-type Streptococcus pyogenes strains with a wild-type or mutated covS gene from a single streptococcal toxic shock syndrome patient.

    Science.gov (United States)

    Masuno, Katsuaki; Okada, Ryo; Zhang, Yan; Isaka, Masanori; Tatsuno, Ichiro; Shibata, Shinichiro; Hasegawa, Tadao

    2014-04-01

    Streptococcal toxic shock syndrome (STSS) is a re-emerging infectious disease in many developed countries. Recent studies have suggested that mutations in CovRS, a two-component regulatory system in Streptococcus pyogenes, play important roles in the pathogenesis of STSS. However, in vivo evidence of the significance of CovRS in human infections has not been fully demonstrated. We investigated five S. pyogenes strains isolated simultaneously from the pharynx, sputum, knee joint, cerebrospinal fluid and blood of a single STSS patient. All were emm89-type strains, and multilocus sequence typing (MLST) analysis revealed that the strains of pharynx and blood were isogenic. The growth rates of the strains from pharynx and sputum were faster than those of the other strains. Protein profiles of the culture supernatants of strains from the pharynx and sputum were also different from those of the other strains. Sequence analyses revealed that strains from the knee joint, cerebrospinal fluid and blood contained a single nucleotide difference in the covS coding region, resulting in one amino acid change, compared with the other strains. Introduction of a plasmid containing the covS gene from the pharynx strain to the blood strain increased the production of SpeB protein. This suggests that the one amino acid alteration in CovS was relevant to pathogenesis. This report supports the idea that mutated CovS plays important roles in vivo in the dissemination of S. pyogenes from the upper respiratory tract of human to aseptic tissues such as blood and cerebrospinal fluid.

  17. Clinicopathological study of nondiabetic renal disease in type 2 diabetic patients: A single center experience from India

    Directory of Open Access Journals (Sweden)

    Kamal V Kanodia

    2017-01-01

    Full Text Available Diabetic nephropathy (DN is a major complication of diabetes mellitus (DM, leading to chronic kidney disease/end-stage renal disease. Wide spectrum of nondiabetic renal diseases (NDRD is reported in type-2 diabetes (type-2 DM. We carried out this single-center study to find clinical, laboratory, and histological features of NDRD in type-2 DM patients and to assess the prevalence of NDRD in India. A single-center retrospective study which included analysis of renal biopsies from patients with type-2 DM, performed between January 2008 and September 2016. Biopsy findings were categorized into three groups, Group-I (isolated NDRD; Group-II (NDRD superimposed on underlying DN; and Group-III (isolated DN. Out of 152 diabetic patients (111 males and 41 females, 35 (23.03% patients were of Group-I (isolated NDRD, 35 (23.03% of Group-II (NDRD superimposed on underlying DN, and 82 (53.95% of Group-III (isolated DN. The mean age (in years was 55.08 ± 10.71, 55.65 ± 8.71, and 54.45 ± 9.01 respectively in Group-I, II, and III. Nephrotic syndrome (NS was the most common clinical presentation in all groups. Duration of DM was significantly shorter in Group-I than in Group-II. Diabetic retinopathy was absent in Group-I. Proteinuria was more in Group-III than Group-I. Low serum C3 and/or C4 levels was observed in five (14.29% cases of Group-I and Group-II each and two (2.43% cases of Group-III. Nearly, 70 (46.05% patients were found to have NDRD either in isolated form or as combined lesions. The most common histological types of NDRD were acute tubulointerstitial nephritis (38.57% followed by benign nephrosclerosis (15.72%, membranous nephropathy (10%, IgA nephropathy (7.14%, and membranoproliferative glomerulonephritis (7.14%. The incidence of NDRD (with/without DN in type-2 DM is very high. Shorter duration of diabetes, hematuria, absence of retinopathy, low serum complement levels, and nephrotic range proteinuria are predictors of NDRD.

  18. Mutations in TP53 tumor suppressor gene in wood dust-related sinonasal cancer

    DEFF Research Database (Denmark)

    Holmila, Reetta; Bornholdt, Jette; Heikkilä, Pirjo

    2010-01-01

    to wood dust, using capillary electrophoresis single-strand conformation polymorphism analysis and direct sequencing. A significant association between wood-dust exposure and adenocarcinoma histology was observed [adjusted odds ratio (OR) 12.6, 95% confidence interval (CI), 5.0-31.6]. TP53 mutations...

  19. Wood Products Other Building Materials Used in New Residential Construction in the United States

    Science.gov (United States)

    David B. McKeever; Joe Elling

    2015-01-01

    On average, new residential construction accounts for about one-third of all wood products consumed in the United States annually. During periods of robust housing activity, 45% or more of all wood products consumed are for new single-family and multifamily housing. This can fall to as low as 20% or less during times of economic recession. Unfortunately, 2012 was not...

  20. Quantifying arthropod contributions to wood decay

    Science.gov (United States)

    Michael Ulyshen; Terry Wagner

    2013-01-01

    Termites carry large amounts of soil into dead wood, and this behaviour complicates efforts to measure their contributions to wood decay. A novel method for isolating termite soil by burning the wood is described, and some preliminary results are presented.

  1. The Type and Impact of Evidence Review Group Exploratory Analyses in the NICE Single Technology Appraisal Process.

    Science.gov (United States)

    Carroll, Christopher; Kaltenthaler, Eva; Hill-McManus, Daniel; Scope, Alison; Holmes, Michael; Rice, Stephen; Rose, Micah; Tappenden, Paul; Woolacott, Nerys

    2017-06-01

    As part of the UK National Institute for Health and Care Excellence (NICE) single technology appraisal process, independent evidence review groups (ERGs) critically appraise a company's submission relating to a specific technology and indication. To explore the type of additional exploratory analyses conducted by ERGs and their impact on the recommendations made by NICE. The 100 most recently completed single technology appraisals with published guidance were selected for inclusion. A content analysis of relevant documents was undertaken to identify and extract relevant data, and narrative synthesis was used to rationalize and present these data. The types of exploratory analysis conducted in relation to companies' models were fixing errors, addressing violations, addressing matters of judgment, and the provision of a new, ERG-preferred base case. Ninety-three of the 100 ERG reports contained at least one of these analyses. The most frequently reported type of analysis in these 93 ERG reports related to the category "Matters of judgment," which was reported in 83 reports (89%). At least one of the exploratory analyses conducted and reported by an ERG is mentioned in 97% of NICE appraisal consultation documents and 94% of NICE final appraisal determinations, and had a clear influence on recommendations in 72% of appraisal consultation documents and 47% of final appraisal determinations. These results suggest that the additional analyses undertaken by ERGs in the appraisal of company submissions are highly influential in the policy-making and decision-making process. Copyright © 2017 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

  2. Structure–property characterization of the crinkle-leaf peach wood phenotype: a future model system for wood properties research?

    Science.gov (United States)

    Alex C. Wiedenhoeft; Rafael Arévalo; Craig Ledbetter; Joseph E. Jakes

    2016-01-01

    Nearly 400 million years of evolution and field-testing by the natural world has given humans thousands of wood types, each with unique structure– property relationships to study, exploit, and ideally, to manipulate, but the slow growth of trees makes them a recalcitrant experimental system. Variations in wood features of two genotypes of peach (Prunus persica L.)...

  3. Does replacing coal with wood lower CO2 emissions? Dynamic lifecycle analysis of wood bioenergy

    Science.gov (United States)

    Sterman, John D.; Siegel, Lori; Rooney-Varga, Juliette N.

    2018-01-01

    Bioenergy is booming as nations seek to cut their greenhouse gas emissions. The European Union declared biofuels to be carbon-neutral, triggering a surge in wood use. But do biofuels actually reduce emissions? A molecule of CO2 emitted today has the same impact on radiative forcing whether it comes from coal or biomass. Biofuels can only reduce atmospheric CO2 over time through post-harvest increases in net primary production (NPP). The climate impact of biofuels therefore depends on CO2 emissions from combustion of biofuels versus fossil fuels, the fate of the harvested land and dynamics of NPP. Here we develop a model for dynamic bioenergy lifecycle analysis. The model tracks carbon stocks and fluxes among the atmosphere, biomass, and soils, is extensible to multiple land types and regions, and runs in ≈1s, enabling rapid, interactive policy design and sensitivity testing. We simulate substitution of wood for coal in power generation, estimating the parameters governing NPP and other fluxes using data for forests in the eastern US and using published estimates for supply chain emissions. Because combustion and processing efficiencies for wood are less than coal, the immediate impact of substituting wood for coal is an increase in atmospheric CO2 relative to coal. The payback time for this carbon debt ranges from 44-104 years after clearcut, depending on forest type—assuming the land remains forest. Surprisingly, replanting hardwood forests with fast-growing pine plantations raises the CO2 impact of wood because the equilibrium carbon density of plantations is lower than natural forests. Further, projected growth in wood harvest for bioenergy would increase atmospheric CO2 for at least a century because new carbon debt continuously exceeds NPP. Assuming biofuels are carbon neutral may worsen irreversible impacts of climate change before benefits accrue. Instead, explicit dynamic models should be used to assess the climate impacts of biofuels.

  4. Exploring single nucleotide polymorphisms previously related to obesity and metabolic traits in pediatric-onset type 2 diabetes.

    Science.gov (United States)

    Miranda-Lora, América Liliana; Cruz, Miguel; Aguirre-Hernández, Jesús; Molina-Díaz, Mario; Gutiérrez, Jorge; Flores-Huerta, Samuel; Klünder-Klünder, Miguel

    2017-07-01

    To evaluate the association of 64 obesity-related polymorphisms with pediatric-onset type 2 diabetes and other glucose- and insulin-related traits in Mexican children. Case-control and case-sibling designs were followed. We studied 99 patients with pediatric-onset type 2 diabetes, their siblings (n = 101) without diabetes, 83 unrelated pediatric controls and 137 adult controls. Genotypes were determined for 64 single nucleotide polymorphisms, and a possible association was examined between those genotypes and type 2 diabetes and other quantitative traits, after adjusting for age, sex and body mass index. In the case-pediatric control and case-adult control analyses, five polymorphisms were associated with increased likelihood of pediatric-onset type 2 diabetes; only one of these polymorphisms (CADM2/rs1307880) also showed a consistent effect in the case-sibling analysis. The associations in the combined analysis were as follows: ADORA1/rs903361 (OR 1.9, 95% CI 1.2; 3.0); CADM2/rs13078807 (OR 2.2, 95% CI 1.2; 4.0); GNPDA2/rs10938397 (OR 2.2, 95% CI 1.4; 3.7); VEGFA/rs6905288 (OR 1.4, 95% CI 1.1; 2.1) and FTO/rs9939609 (OR 1.8, 95% CI 1.0; 3.2). We also identified 16 polymorphisms nominally associated with quantitative traits in participants without diabetes. ADORA/rs903361, CADM2/rs13078807, GNPDA2/rs10938397, VEGFA/rs6905288 and FTO/rs9939609 are associated with an increased risk of pediatric-onset type 2 diabetes in the Mexican population.

  5. Evaluation of XRF and LIBS technologies for on-line sorting of CCA-treated wood waste.

    Science.gov (United States)

    Solo-Gabriele, Helena M; Townsend, Timothy G; Hahn, David W; Moskal, Thomas M; Hosein, Naila; Jambeck, Jenna; Jacobi, Gary

    2004-01-01

    Contamination of wood waste with chromated copper arsenate greatly limits recycling opportunities for the wood waste as a whole. Separation of CCA-treated wood from other wood types is one means by which such contamination can be removed. The purpose of the current study was to evaluate two detector technologies for sorting CCA-treated wood from other wood types. The detector technologies evaluated included X-ray fluorescence spectroscopy (XRF) and laser induced breakdown spectroscopy (LIBS). The XRF detector system utilized in this study was capable of rapidly detecting the presence of CCA in painted wood, wet wood, heartwood, sapwood, and at portions of the wood containing knots. Furthermore, the XRF system was capable of distinguishing between CCA-treated wood and wood treated with alternative wood treatment preservatives, but was limited by the fact that it was not designed for on-line operation so tests were conducted in a batch mode on a conveyor. The analysis time used in this study (3 s) can be decreased significantly for an XRF system designed specifically for on-line operation. The LIBS system developed for this study was found to effectively identify CCA-treated wood for pieces ranging in thickness from 1 to 8 cm. High sorting efficiencies were noted when 10 laser shots were taken on a piece of wood. Furthermore, the LIBS system was found to be effective for identifying wood that has been coated with stains and paints in addition to identifying wood that has been CCA treated. The major drawback with the LIBS system developed in this study was the limited laser pulse energy. With an increase in laser pulse energy it is anticipated that the working focal length of the LIBS system can be increased to enable the monitoring of wood samples of more variable thicknesses. Limitations associated with analysis of very rotted pieces of wood and wet wood can also be overcome by using a higher pulse energy laser. Overall, both technologies show incredible promise for

  6. Single nucleotide polymorphism typing of Mycobacterium ulcerans reveals focal transmission of buruli ulcer in a highly endemic region of Ghana.

    Directory of Open Access Journals (Sweden)

    Katharina Röltgen

    Full Text Available Buruli ulcer (BU is an emerging necrotizing disease of the skin and subcutaneous tissue caused by Mycobacterium ulcerans. While proximity to stagnant or slow flowing water bodies is a risk factor for acquiring BU, the epidemiology and mode of M. ulcerans transmission is poorly understood. Here we have used high-throughput DNA sequencing and comparisons of the genomes of seven M. ulcerans isolates that appeared monomorphic by existing typing methods. We identified a limited number of single nucleotide polymorphisms (SNPs and developed a real-time PCR SNP typing method based on these differences. We then investigated clinical isolates of M. ulcerans on which we had detailed information concerning patient location and time of diagnosis. Within the Densu river basin of Ghana we observed dominance of one clonal complex and local clustering of some of the variants belonging to this complex. These results reveal focal transmission and demonstrate, that micro-epidemiological analyses by SNP typing has great potential to help us understand how M. ulcerans is transmitted.

  7. Analysis of horse myostatin gene and identification of single nucleotide polymorphisms in breeds of different morphological types.

    Science.gov (United States)

    Dall'Olio, Stefania; Fontanesi, Luca; Nanni Costa, Leonardo; Tassinari, Marco; Minieri, Laura; Falaschini, Adalberto

    2010-01-01

    Myostatin (MSTN) is a negative modulator of muscle mass. We characterized the horse (Equus caballus) MSTN gene and identified and analysed single nucleotide polymorphisms (SNPs) in breeds of different morphological types. Sequencing of coding, untranslated, intronic, and regulatory regions of MSTN gene in 12 horses from 10 breeds revealed seven SNPs: two in the promoter, four in intron 1, and one in intron 2. The SNPs of the promoter (GQ183900:g.26T>C and GQ183900:g.156T>C, the latter located within a conserved TATA-box like motif) were screened in 396 horses from 16 breeds. The g.26C and the g.156C alleles presented higher frequency in heavy (brachymorphic type) than in light breeds (dolichomorphic type such as Italian Trotter breed). The significant difference of allele frequencies for the SNPs at the promoter and analysis of molecular variance (AMOVA) on haplotypes indicates that these polymorphisms could be associated with variability of morphology traits in horse breeds.

  8. A novel high-resolution single locus sequence typing scheme for mixed populations of Propionibacterium acnes in vivo.

    Directory of Open Access Journals (Sweden)

    Christian F P Scholz

    Full Text Available The Gram-positive anaerobic bacterium Propionibacterium acnes is a prevalent member of the normal skin microbiota of human adults. In addition to its suspected role in acne vulgaris it is involved in a variety of opportunistic infections. Multi-locus sequence-typing (MLST schemes identified distinct phylotypes associated with health and disease. Being based on 8 to 9 house-keeping genes these MLST schemes have a high discriminatory power, but their application is time- and cost-intensive. Here we describe a single-locus sequence typing (SLST scheme for P. acnes. The target locus was identified with a genome mining approach that took advantage of the availability of representative genome sequences of all known phylotypes of P. acnes. We applied this SLST on a collection of 188 P. acnes strains and demonstrated a resolution comparable to that of existing MLST schemes. Phylogenetic analysis applied to the SLST locus resulted in clustering patterns identical to a reference tree based on core genome sequences. We further demonstrate that SLST can be applied to detect multiple phylotypes in complex microbial communities by a metagenomic pyrosequencing approach. The described SLST strategy may be applied to any bacterial species with a basically clonal population structure to achieve easy typing and mapping of multiple phylotypes in complex microbiotas. The P. acnes SLST database can be found at http://medbac.dk/slst/pacnes.

  9. Analysis of Horse Myostatin Gene and Identification of Single Nucleotide Polymorphisms in Breeds of Different Morphological Types

    Directory of Open Access Journals (Sweden)

    Stefania Dall'Olio

    2010-01-01

    Full Text Available Myostatin (MSTN is a negative modulator of muscle mass. We characterized the horse (Equus caballus MSTN gene and identified and analysed single nucleotide polymorphisms (SNPs in breeds of different morphological types. Sequencing of coding, untranslated, intronic, and regulatory regions of MSTN gene in 12 horses from 10 breeds revealed seven SNPs: two in the promoter, four in intron 1, and one in intron 2. The SNPs of the promoter (GQ183900:g.26T>C and GQ183900:g.156T>C, the latter located within a conserved TATA-box like motif were screened in 396 horses from 16 breeds. The g.26C and the g.156C alleles presented higher frequency in heavy (brachymorphic type than in light breeds (dolichomorphic type such as Italian Trotter breed. The significant difference of allele frequencies for the SNPs at the promoter and analysis of molecular variance (AMOVA on haplotypes indicates that these polymorphisms could be associated with variability of morphology traits in horse breeds.

  10. Properties and local environment of p-type and photoluminescent rare earths implanted into ZnO single crystals

    CERN Document Server

    Rita, EMC; Wahl, U; Soares, JC

    This thesis presents an experimental study of the local environment of p-type and Rare- Earth dopants implanted in ZnO single-crystals (SCs). Various nuclear and bulk property techniques were combined in the following evaluations: Implantation damage annealing was evaluated in ZnO SCs implanted with Fe, Sr and Ca. P-type dopants Cu and Ag implanted ZnO SCs were studied revealing that the solubility of Cu in substituting Zn is considerably higher than that of Ag. These results are discussed within the scope of the ZnO p-type doping problematic with these elements. Experimental proofs of the As “anti-site” behavior in ZnO were for the first time attained, i.e., the majority of As atoms are substitutional at the Zn site (SZn), possibly surrounded by two Zn vacancies (VZn). This reinforces the theoretical prediction that As acts as an acceptor in ZnO via the AsZn-2VZn complex formation. The co-doping of ZnO SC with In (donor) and As (acceptor) was addressed. The most striking result is the possible In-As “p...

  11. Effect of separator and inoculum type on electricity generation and microbial community in single-chamber microbial fuel cells.

    Science.gov (United States)

    Yu, Jaecheul; Park, Younghyun; Lee, Taeho

    2014-04-01

    Single-chamber microbial fuel cell (SMFC)-I consisted of 4 separator-electrode assemblies (SEAs) with two types of cation exchange membrane (CEM: Nafion and CMI 7000) and an anion exchange membrane (AEM: AMI 7001). SMFC-II consisted of 4 SEAs with Nafion and three types of nonwoven fabric. SMFC-I and -II were inoculated with anaerobic digested and activated sludge, respectively, and operated under fed-batch mode. In SMFC I, AEM-SEA showed a maximum power density (PDmax). Nafion-SEA showed a PDmax in SMFC II, which was similar to that of Nafion-SEA of SMFC I. Although different bacteria were developed in SMFC-I (Deltaproteobacteria and Firmicutes) and SMFC-II (Gammaproteobacteria, Betaproteobacteria and Bacteroidetes), the inoculum type little affects electricity generation. Variations of pH and oxygen in biofilm have influenced microbial community structure and electricity generation according to the electrode and separator material. Although the electricity generation of non-woven fabric-SEA was less than that of Nafion-SEA, the use of non-woven fabrics is expected to reduce the construction and operating costs of MFCs.

  12. Development and evaluation of one step single tube multiplex RT-PCR for rapid detection and typing of dengue viruses

    Directory of Open Access Journals (Sweden)

    Parida Manmohan

    2008-01-01

    Full Text Available Abstract Background Dengue is emerging as a major public health concern in many parts of the world. The development of a one-step, single tube, rapid, and multiplex reverse transcription polymerase chain reaction (M-RT-PCR for simultaneous detection and typing of dengue virus using serotype specific primers during acute phase of illness is reported. Results An optimal assay condition with zero background was established having no cross-reaction with closely related members of flavivirus (Japanese encephalitis, West Nile, Yellow fever and alphavirus (Chikungunya. The feasibility of M-RT-PCR assay for clinical diagnosis was validated with 620 acute phase dengue patient sera samples of recent epidemics in India. The comparative evaluation vis a vis conventional virus isolation revealed higher sensitivity. None of the forty healthy serum samples screened in the present study revealed any amplification, thereby establishing specificity of the reported assay for dengue virus only. Conclusion These findings clearly suggested that M-RT-PCR assay reported in the present study is the rapid and cost-effective method for simultaneous detection as well as typing of the dengue virus in acute phase patient serum samples. Thus, the M-RT-PCR assay developed in this study will serve as a very useful tool for rapid diagnosis and typing of dengue infections in endemic areas.

  13. Assessment and management of dead-wood habitat

    Science.gov (United States)

    Hagar, Joan

    2007-01-01

    consequence of these practices, dead wood has been reduced by as much as 90% after two rotations of managed Douglas-fir (Rose et al., 2001). Large legacy deadwood is becoming a scarce, critical habitat that will take decades to centuries to replace. Furthermore, management continues to have important direct and indirect effects on the amount and distribution of dead wood in forests. Current guidelines for managing dead wood may be inadequate to maintain habitat for all associated species because they largely focus on a single use of dead wood (nesting habitat) by a small suite of species (cavity-nesting birds), and may under represent the sizes and amounts of dead wood used by many wildlife species (Rose et al., 2001, Wilhere, 2003). 

  14. A Study on the Effect of Plasma Treatment for Waste Wood Biocomposites

    Directory of Open Access Journals (Sweden)

    MiMi Kim

    2013-01-01

    Full Text Available The surface modification of wood powder by atmospheric pressure plasma treatment was investigated. The composites were manufactured using wood powder and polypropylene (wood powder: polypropylene = 55 wt% : 45 wt%. Atmospheric pressure plasma treatment was applied under the condition of 3 KV, 17±1 KHz, 2 g/min. Helium was used as the carrier gas and hexamethyl-disiloxane (HMDSO as the monomer to modify the surface property of the waste wood biocomposites by plasma polymerization. The tensile strengths of untreated waste wood powder (W3 and single species wood powder (S3 were about 18.5 MPa and 21.5 MPa while those of plasma treated waste wood powder (PW3 and plasma treated single species wood powder (PS3 were about 21.2 MPa and 23.4 MPa, respectively. Tensile strengths of W3 and S3 were improved by 14.6% and 8.8%, respectively. From the analyses of mechanical properties and morphology, we conclude that the interfacial bonding of polypropylene and wood powder can be improved by atmospheric pressure plasma treatment.

  15. EIT Detection of Juvenile and Knot Wood in Southern Pine Logs

    OpenAIRE

    Steel, PH; Cooper, JE; Boden, C; Lionheart, WRB

    2007-01-01

    Abstract: The juvenile wood type is produced by southern pine trees during their first 10 years of growth producing a significant volume of wood at tree center having inferior properties that decrease lumber value. Increased volumes of lumber are influenced by juvenile wood as intensive plantation silviculture increases early tree growth. Research has shown that knowledge of knot location in logs prior to sawing has the potential to significantly increase lumber value yield. Detection of ...

  16. Properties of seven Colombian woods

    Science.gov (United States)

    B. A. Bendtsen; M. Chudnoff

    1981-01-01

    Woods from abroad are an important raw material to the forest products industries in the United States. A major concern in effective utilization of this resource is the lack of technical information on many species. This report presents the results of an evaluation of the mechanical properties of small, clear specimens of seven Colombian woods. These results are...

  17. Moisture transport in coated wood

    NARCIS (Netherlands)

    Meel, P.A. van; Erich, S.J.F.; Huinink, H.P.; Kopinga, K.; Jong, J. DE; Adan, O.C.G.

    2011-01-01

    Moisture accumulation inside wood causes favorable conditions for decay. Application of a coating alters the moisture sorption of wood and prevents accumulation of moisture. This paper presents the results of a nuclear magnetic resonance (NMR) study on the influence of a coating on the moisture

  18. The sustainable wood production initiative.

    Science.gov (United States)

    Robert. Deal

    2004-01-01

    To address concerns about sustainable forestry in the region, the Focused Science Delivery Program is sponsoring a three year Sustainable Wood Production Initiative. The Pacific Northwest is one of the world's major timber producing regions, and the ability of this region to produce wood on a sustained yield basis is widely recognized. Concerns relating to the...

  19. Measuring wood specific gravity, correctly

    Science.gov (United States)

    G. Bruce Williamson; Michael C. Wiemann

    2010-01-01

    The specific gravity (SG) of wood is a measure of the amount of structural material a tree species allocates to support and strength. In recent years, wood specific gravity, traditionally a forester’s variable, has become the domain of ecologists exploring the universality of plant functional traits and conservationists estimating global carbon stocks. While these...

  20. On Erdos–Wood's conjecture

    Indian Academy of Sciences (India)

    In this article, we prove that infinite number of integers satsify Erdős–Woods conjecture. Moreover, it follows that the number of natural numbers ≤ satisfies Erdős–Woods conjecture with = 2 is at least /(log ) for some positive constant > 2.

  1. Composites from wood and plastics

    Science.gov (United States)

    Craig Clemons

    2010-01-01

    Composites made from thermoplastics and fillers or reinforcements derived from wood or other natural fibers are a dynamic research area encompassing a wide variety of composite materials. For example, as the use of biopolymers grows, wood and other natural fiber sources are being investigated as renewable sources of fillers and reinforcements to modify performance....

  2. The wood of Merovingian weaponry

    Czech Academy of Sciences Publication Activity Database

    Tegel, W.; Muigg, B.; Büntgen, Ulf

    2016-01-01

    Roč. 65, JAN (2016), s. 148-153 ISSN 0305-4403 R&D Projects: GA MŠk(CZ) EE2.3.20.0248 Institutional support: RVO:67179843 Keywords : Early Middle Ages * Merovingian weaponry * Mineralised wood * Wood anatomy Subject RIV: EH - Ecology, Behaviour Impact factor: 2.602, year: 2016

  3. Public opinion and wood energy

    Science.gov (United States)

    Sarah Hitchner; John Schelhas; Teppo Hujala; J. Peter Brosius

    2014-01-01

    As wood-based bioenergy continues to develop around the world, it will utilize forestlands in new ways and will have different effects on a number of stakeholders, including forest landowners, local communities, extant industries, policymakers, investors, and others. As more stakeholders become involved in the wood energy web, and as the general public becomes more...

  4. Particulate emissions from residential wood combustion

    DEFF Research Database (Denmark)

    Luis Teles de Carvalho, Ricardo; Jensen, Ole Michael; Tarelho, Luis A. C.

    Residential wood combustion (RWC) in fireplaces and conventional appliances is the main contributor to fine particulate matter (PM2.5) emissions in Denmark and Portugal representing more than 30% of the total emissions [1;2]. Such estimations are uncertain concerning the wood consumption...... and official emission factors, not taking into account actual burning conditions in dwellings [3]. There is limited knowledge on the real-life performance and spatial distribution of existing appliance types. Few studies have been targeting to understand the influence of fuel operation habits on PM2.5...... the available estimations for Denmark and Portugal, suggesting a methodology to increase the accuracy of activity data and emission factors. This work is based on new studies carried out to quantify the PM2.5 emissions in daily life through field experiments in Danish dwellings and by considering typical...

  5. Study of influence of 2.4 GHz electromagnetic waves on electrophysical properties of coniferous trees wood

    Science.gov (United States)

    Abdurahimov, Nursulton; Lagunov, Alexey; Melehov, Vladimir

    2017-09-01

    Climate change has a significant impact on changing weather conditions in the Arctic. Wood is a traditional building material in the North of Russia. Supports of communication lines are made of wood. Dry wood is a solid dielectric with a low conductivity. At the same time it is porous material having high hygroscopicity. The presence of moisture leads to wood rotting. To prevent rotting of a support it needs to be impregnated with antiseptics. A tree dried by means of convection drying cannot provide required porosity of wood for impregnation. Our studies of electrophysical properties of coniferous species showed that microwave drying of wood increases the porosity of the wood. Wood dried in this way is easily impregnated with antiseptics. Thorough wood drying requires creating optimal conditions in a microwave oven. During the drying process in a chamber there is a resonant phenomenon. These phenomena depend on electro-physical properties of the material placed in the chamber. Dielectric constant of wood has the most influence. A resonator method to determine the dielectric constant of the wood was used. The values of permittivity for the spruce and pine samples were determined. The measured value of the dielectric constant of wood was used to provide optimal matching of the generator with the resonator in a wood-drying resonator type microwave chamber, and to maintain it in the process of wood drying. It resulted in obtaining the samples with a higher permeability of wood in radial and longitudinal direction. This creates favorable conditions for wood impregnation with antiseptics and flame retardants. Timber dried by means of electromagnetic waves in the 2.4 GHz band has a deeper protective layer. The support made of such wood will serve longer as supports of communication lines.

  6. Solid wood timber products consumption in major end uses in the United States, 1950-2009 : a technical document supporting the Forest Service 2010 RPA assessment

    Science.gov (United States)

    David B. McKeever; James L. Howard

    2011-01-01

    Solid wood timber products provide important raw materials to the construction, manufacturing, and shipping sectors of the U.S. economy. Nearly all new single-family houses and low-rise multifamily residential structures are wood framed and sheathed. Large amounts of solid wood timber products are also used in the construction of new nonresidential buildings, and in...

  7. Asthma in furniture and wood processing workers: a systematic review.

    Science.gov (United States)

    Wiggans, R E; Evans, G; Fishwick, D; Barber, C M

    2016-04-01

    Wood dust is a common cause of occupational asthma. There is potential for high exposure to wood dust during furniture and wood manufacturing processes. To evaluate the evidence for non-neoplastic respiratory ill health associated with work in the furniture and wood manufacturing sector. A systematic review was performed according to PRISMA guidelines. Articles were graded using SIGN (Scottish Intercollegiate Guideline Network) and MERGE (Methods for Evaluating Research Guidelines and Evidence) criteria, with data grouped by study outcome. Initial searches identified 1328 references, from which 55 articles were included in the review. Fourteen studies were graded A using MERGE or >2++ using SIGN. All but one paper describing airway symptoms reported an increased risk in higher wood dust exposed workers in comparison to lower or non-exposed groups. Five studies reporting asthma examined dose response; three found a positive effect. The relative risk for asthma in exposed workers in the single meta-analysis was 1.5 (95% CI 1.25-1.87). Two studies reported more obstructive lung function (forced expiratory volume in 1 s [FEV1]/forced vital capacity < 0.7) in exposed populations. Excess longitudinal FEV1 decline was reported in female smokers with high wood dust exposures in one study population. Where measured, work-related respiratory symptoms did not clearly relate to specific wood immunoglobulin E positivity. Work in this sector was associated with a significantly increased risk of respiratory symptoms and asthma. The evidence for wood dust exposure causing impaired lung function is less clearly established. Further study is required to better understand the prevalence, and causes, of respiratory problems within this sector. © Crown copyright 2015.

  8. Characterisation of wood combustion ashes

    DEFF Research Database (Denmark)

    Maresca, Alberto

    The combustion of wood chips and wood pellets for the production of renewable energy in Denmark increased from 5.7 PJ to 16 PJ during the period 2000-2015, and further increases are expected to occur within the coming years. In 2012, about 22,300 tonnes of wood ashes were generated in Denmark....... Currently, these ashes are mainly landfilled, despite Danish legislation allowing their application onto forest and agricultural soils for fertilising and/or liming purposes. During this PhD work, 16 wood ash samples generated at ten different Danish combustion plants were collected and characterised...... for their composition and leaching properties. Despite the relatively large variations in the contents of nutrients and trace metals, the overall levels were comparable to typical ranges reported in the literature for other wood combustion ashes, as well as with regards to leaching. In general, the composition...

  9. Origin of Petrified Wood Color

    Directory of Open Access Journals (Sweden)

    George Mustoe

    2016-05-01

    Full Text Available Fossil forests have world-wide distribution, commonly preserving mineralized wood that displays vivid hues and complex color patterns. However, the origin of petrified color has received little scientific attention. Color of silicified wood may be influenced by the presence of relict organic matter, but the most significant contribution comes from trace metals. This study reports quantitative analysis of trace metals in 35 silicified wood samples, determined using LA-ICP-MS spectrometry. The most important of these metals is Fe, which can produce a rainbow of hues depending on its abundance and oxidation state. Cr is the dominant colorant for bright green fossil wood from Arizona, USA and Zimbabwe, Africa. Complex color patterns result from the progressive nature of the fossilization process, which causes wood to have varying degrees of permeability during successive episodes of permineralization. These processes include simple diffusion, chromatographic separation, infiltration of groundwater along fractures and void spaces, and oxidation/reduction.

  10. Network type sp3 boron-based single-ion conducting polymer electrolytes for lithium ion batteries

    Science.gov (United States)

    Deng, Kuirong; Wang, Shuanjin; Ren, Shan; Han, Dongmei; Xiao, Min; Meng, Yuezhong

    2017-08-01

    Electrolytes play a vital role in modulating lithium ion battery performance. An outstanding electrolyte should possess both high ionic conductivity and unity lithium ion transference number. Here, we present a facile method to fabricate a network type sp3 boron-based single-ion conducting polymer electrolyte (SIPE) with high ionic conductivity and lithium ion transference number approaching unity. The SIPE was synthesized by coupling of lithium bis(allylmalonato)borate (LiBAMB) and pentaerythritol tetrakis(2-mercaptoacetate) (PETMP) via one-step photoinitiated in situ thiol-ene click reaction in plasticizers. Influence of kinds and content of plasticizers was investigated and the optimized electrolytes show both outstanding ionic conductivity (1.47 × 10-3 S cm-1 at 25 °C) and high lithium transference number of 0.89. This ionic conductivity is among the highest ionic conductivity exhibited by SIPEs reported to date. Its electrochemical stability window is up to 5.2 V. More importantly, Li/LiFePO4 cells with the prepared single-ion conducting electrolytes as the electrolyte as well as the separator display highly reversible capacity and excellent rate capacity under room temperature. It also demonstrates excellent long-term stability and reliability as it maintains capacity of 124 mA h g-1 at 1 C rate even after 500 cycles without obvious decay.

  11. Single locus typing of MHC class I and class II B loci in a population of red jungle fowl.

    Science.gov (United States)

    Worley, K; Gillingham, M; Jensen, P; Kennedy, L J; Pizzari, T; Kaufman, J; Richardson, D S

    2008-05-01

    In species with duplicated major histocompatibility complex (MHC) genes, estimates of genetic variation often rely on multilocus measures of diversity. It is possible that such measures might not always detect more detailed patterns of selection at individual loci. Here, we describe a method that allows us to investigate classical MHC diversity in red jungle fowl (Gallus gallus), the wild ancestor of the domestic chicken, using a single locus approach. This is possible due to the well-characterised gene organisation of the 'minimal essential' MHC (BF/BL region) of the domestic chicken, which comprises two differentially expressed duplicated class I (BF) and two class II B (BLB) genes. Using a combination of reference strand-mediated conformation analysis, cloning and sequencing, we identify nine BF and ten BLB alleles in a captive population of jungle fowl. We show that six BF and five BLB alleles are from the more highly expressed locus of each gene, BF2 and BLB2, respectively. An excess of non-synonymous substitutions across the jungle fowl BF/BL region suggests that diversifying selection has acted on this population. Importantly, single locus screening reveals that the strength of selection is greatest on the highly expressed BF2 locus. This is the first time that a population of red jungle fowl has been typed at the MHC region, laying the basis for further research into the underlying processes acting to maintain MHC diversity in this and other species.

  12. Experimental determination of the yield stress curve of the scotch pine wood materials

    Science.gov (United States)

    Günay, Ezgi; Aygün, Cevdet; Kaya, Şükrü Tayfun

    2013-12-01

    Yield stress curve is determined for the pine wood specimens by conducting a series of tests. In this work, pinewood is modeled as a composite material with transversely isotropic fibers. Annual rings (wood grain) of the wood specimens are taken as the major fiber directions with which the strain gauge directions are aligned. For this purpose, three types of tests are arranged. These are tensile, compression and torsion loading tests. All of the tests are categorized with respect to fiber orientations and their corresponding loading conditions. Each test within these categories is conducted separately. Tensile and compression tests are conducted in accordance with standards of Turkish Standards Institution (TSE) whereas torsion tests are conducted in accordance with Standards Australia. Specimens are machined from woods of Scotch pine which is widely used in boat building industries and in other structural engineering applications. It is determined that this species behaves more flexibly than the others. Strain gauges are installed on the specimen surfaces in such a way that loading measurements are performed along directions either parallel or perpendicular to the fiber directions. During the test and analysis phase of yield stress curve, orientation of strain gauge directions with respect to fiber directions are taken into account. The diagrams of the normal stress vs. normal strain or the shear stress vs. shear strain are plotted for each test. In each plot, the yield stress is determined by selecting the point on the diagram, the tangent of which is having a slope of 5% less than the slope of the elastic portion of the diagram. The geometric locus of these selected points constitutes a single yield stress curve on σ1-σ2 principal plane. The resulting yield stress curve is plotted as an approximate ellipse which resembles Tsai-Hill failure criterion. The results attained in this work, compare well with the results which are readily available in the literature.

  13. The influence of the type of embryo culture medium on neonatal birthweight after single embryo transfer in IVF.

    Science.gov (United States)

    Vergouw, Carlijn G; Kostelijk, E Hanna; Doejaaren, Els; Hompes, Peter G A; Lambalk, Cornelis B; Schats, Roel

    2012-09-01

    Does the type of medium used to culture fresh and frozen-thawed embryos influence neonatal birthweight after single embryo transfer (SET) in IVF? A comparison of two commercially available culture media showed no significant influence on mean birthweight and mean birthweight adjusted for gestational age, gender and parity (z-scores) of singletons born after a fresh or frozen-thawed SET. Furthermore, we show that embryo freezing and thawing cycles may lead to a significantly higher mean birthweight. Animal studies have shown that culture media constituents are responsible for changes in birthweight of offspring. In human IVF, there is still little knowledge of the effect of medium type on birthweight. Until now, only a small number of commercially available culture media have been investigated (Vitrolife, Cook(®) Medical and IVF online medium). Our study adds new information: it has a larger population of singleton births compared with the previously published studies, it includes outcomes of other media types (HTF and Sage(®)), not previously analysed, and it includes data on frozen-thawed SETs. This study was a retrospective analysis of birthweights of singleton newborns after fresh (Day 3) or frozen-thawed (Day 5) SET cycles, using embryos cultured in either of two different types of commercially available culture media, between 2008 and 2011. Before January 2009, a single-step culture medium was used: human tubal fluid (HTF) with 4 mg/ml human serum albumin. From January 2009 onwards, a commercially available sequential medium was introduced: Sage(®), Quinn's advantage protein plus medium. Singletons born after a fresh SET (99 embryos cultured in HTF and 259 in Sage(®)) and singletons born after a frozen-thawed SET (32 embryos cultured in HTF only, 41 in HTF and Sage(®) and 86 in Sage(®) only) were analysed. Only patients using autologous gametes without the use of a gestational carrier were considered. Also excluded were (vanishing) twins, triplets

  14. Projected wood energy impact on US forest wood resources

    Energy Technology Data Exchange (ETDEWEB)

    Skog, K.E. [USDA Forest Service, Madison, WI (United States)

    1993-12-31

    The USDA Forest Service has developed long-term projections of wood energy use as part of a 1993 assessment of demand for and supply of resources from forest and range lands in the United States. To assess the impact of wood energy demand on timber resources, a market equilibrium model based on linear programming was developed to project residential, industrial, commercial, and utility wood energy use from various wood energy sources: roundwood from various land sources, primary wood products mill residue, other wood residue, and black liquor. Baseline projections are driven by projected price of fossil fuels compared to price of wood fuels and the projected increase in total energy use in various end uses. Wood energy use is projected to increase from 2.67 quad in 1986 to 3.5 quad in 2030 and 3.7 quad in 2040. This is less than the DOE National Energy Strategy projection of 5.5 quad in 2030. Wood energy from forest sources (roundwood) is projected to increase from 3.1 billion (10{sup 9}) ft{sup 3} in 1986 to 4.4. billion ft{sup 3} in 2030 and 4.8 billion ft{sup 3} in 2040 (88, 124 and 136 million m{sup 3}, respectively). This rate of increase of roundwood use for fuel -- 0.8 percent per year -- is virtually the same as the projected increase rate for roundwood for pulpwood. Pulpwood roundwood is projected to increase from 4.2 billion ft{sup 3} in 1986 to 6.0 billion ft{sup 3} in 2030 and 6.4 billion ft{sup 3} in 2040 (119, 170 and 183 million m{sup 3}, respectively).

  15. The [Fe(III)[Fe(III)(L1)2]3] star-type single-molecule magnet.

    Science.gov (United States)

    Saalfrank, Rolf W; Scheurer, Andreas; Bernt, Ingo; Heinemann, Frank W; Postnikov, Andrei V; Schünemann, Volker; Trautwein, Alfred X; Alam, Mohammad S; Rupp, Holger; Müller, Paul

    2006-06-21

    Star-shaped complex [Fe(III)[Fe(III)(L1)2]3] (3) was synthesized starting from N-methyldiethanolamine H2L1 (1) and ferric chloride in the presence of sodium hydride. For 3, two different high-spin iron(III) ion sites were confirmed by Mössbauer spectroscopy at 77 K. Single-crystal X-ray structure determination revealed that 3 crystallizes with four molecules of chloroform, but, with only three molecules of dichloromethane. The unit cell of 3.4CHCl3 contains the enantiomers (delta)-[(S,S)(R,R)(R,R)] and (lambda)-[(R,R)(S,S)(S,S)], whereas in case of 3.3CH2Cl2 four independent molecules, forming pairs of the enantiomers [lambda-(R,R)(R,R)(R,R)]-3 and [lambda-(S,S)(S,S)(S,S)]-3, were observed in the unit cell. According to SQUID measurements, the antiferromagnetic intramolecular coupling of the iron(III) ions in 3 results in a S = 10/2 ground state multiplet. The anisotropy is of the easy-axis type. EPR measurements enabled an accurate determination of the ligand-field splitting parameters. The ferric star 3 is a single-molecule magnet (SMM) and shows hysteretic magnetization characteristics below a blocking temperature of about 1.2 K. However, weak intermolecular couplings, mediated in a chainlike fashion via solvent molecules, have a strong influence on the magnetic properties. Scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS) were used to determine the structural and electronic properties of star-type tetranuclear iron(III) complex 3. The molecules were deposited onto highly ordered pyrolytic graphite (HOPG). Small, regular molecule clusters, two-dimensional monolayers as well as separated single molecules were observed. In our STS measurements we found a rather large contrast at the expected locations of the metal centers of the molecules. This direct addressing of the metal centers was confirmed by DFT calculations.

  16. Aspectos da composição química e aceitação sensorial da aguardente de cana-de-açúcar envelhecida em tonéis de diferentes madeiras Aspects of the chemical composition and sensorial acceptance of sugar cane spirit aged in casks of different types of woods

    Directory of Open Access Journals (Sweden)

    André Ricardo Alcarde

    2010-05-01

    sugar cane spirit aged for 3 years in casks of different types of wood (peanut wood, araruva or striped wood, red cabreuva, oak, cherrywood, Brazilian gold wood, purple tabebuia, cariniana legalis, and pear tree. The simple alcoholic distillate which originated the sugar cane spirit was produced at the Distillery of ESALQ/USP. After aging, the sugar cane spirits were analyzed in terms of ethanol concentrations o, volatile acidity, furfural, aldehydes, esters, higher alcohols, methanol, copper, total phenolic compounds, color, and sensorial acceptance. Regardless the type of wood the casks were made of, the aged sugar cane spirits became darker and presented higher concentrations of volatile acidity, furfural, esters, higher alcohols, congeners, and total phenolic compounds than the simple alcoholic distillate. On the other hand, the aged sugar cane spirits presented lower concentrations of aldehydes, methanol, and copper than the simple alcoholic distillate. The statistical analysis, considering the global physicochemical composition of the sugar cane spirits aged in the casks made of different types of wood, showed similarities among the sugar cane spirits aged in the casks of peanut wood, araruva or striped wood, and cariniana legalis. It also indicates similarities among the sugar cane spirits aged in the casks of red cabreuva and pear tree and among the sugar cane spirits aged in the casks of oak, cherrywood, Brazilian gold wood, and purple tabebuia. The sugar cane spirits aged in the casks of the different types of wood were in accordance with the composition and quality standards established by the Brazilian laws. The sugar cane spirit aged in oak presented the best sensorial acceptance. Among the Brazilian woods, purple tabebuia, peanut wood, red cabreuva, cherrywood and pear tree were those that produced sugar cane spirits with better sensorial qualities.

  17. FIELD-SCALE LEACHING OF ARSENIC, CHROMIUM AND COPPER FROM WEATHERED TREATED WOOD

    Science.gov (United States)

    Hasan, A. Rasem; Hu, Ligang; Solo-Gabriele, Helena M.; Fieber, Lynne; Cai, Yong; Townsend, Timothy G.

    2010-01-01

    Earlier studies documented the loss of wood preservatives from new wood. The objective of this study was to evaluate losses from weathered treated wood under field conditions by collecting rainfall leachate from 5 different wood types, all with a surface area of 0.21 m2. Wood samples included weathered chromate copper arsenate (CCA) treated wood at low (2.7 kg/m3), medium (4.8 kg/m3) and high (35.4 kg/m3) retention levels, new alkaline copper quat (ACQ) treated wood (1.1 kg/m3 as CuO) and new untreated wood. Arsenic was found to leach at a higher rate (100 mg in 1 year for low retention) than chromium and copper (leached at the highest rate from the ACQ sample (670 mg). Overall results suggest that metals’ leaching is a continuous process driven by rainfall, and that the mechanism of release from the wood matrix changes as wood weathers. PMID:20053493

  18. 229 nm UV LEDs on aluminum nitride single crystal substrates using p-type silicon for increased hole injection

    Science.gov (United States)

    Liu, Dong; Cho, Sang June; Park, Jeongpil; Seo, Jung-Hun; Dalmau, Rafael; Zhao, Deyin; Kim, Kwangeun; Gong, Jiarui; Kim, Munho; Lee, In-Kyu; Albrecht, John D.; Zhou, Weidong; Moody, Baxter; Ma, Zhenqiang

    2018-02-01

    AlGaN based 229 nm light emitting diodes (LEDs), employing p-type Si to significantly increase hole injection, were fabricated on single crystal bulk aluminum nitride (AlN) substrates. Nitride heterostructures were epitaxially deposited by organometallic vapor phase epitaxy and inherit the low dislocation density of the native substrate. Following epitaxy, a p-Si layer is bonded to the heterostructure. LEDs were characterized both electrically and optically. Owing to the low defect density films, large concentration of holes from p-Si, and efficient hole injection, no efficiency droop was observed up to a current density of 76 A/cm2 under continuous wave operation and without external thermal management. An optical output power of 160 μW was obtained with the corresponding external quantum efficiency of 0.03%. This study demonstrates that by adopting p-type Si nanomembrane contacts as a hole injector, practical levels of hole injection can be realized in UV light-emitting diodes with very high Al composition AlGaN quantum wells, enabling emission wavelengths and power levels that were previously inaccessible using traditional p-i-n structures with poor hole injection efficiency.

  19. Strain typing of Zygosaccharomyces yeast species using a single molecular method based on polymorphism of the intergenic spacer region (IGS).

    Science.gov (United States)

    Wrent, Petra; Rivas, Eva-María; Peinado, José M; de Silóniz, María-Isabel

    2010-08-15

    Unlike previously reported methods that need a combination of several typing techniques, we have developed a single method for strain typing of the Zygosaccharomyces bailii, Z. mellis and Z. rouxii spoilage species. Strains belonging to other species have also been included for comparison. We have demonstrated that the IGS-PCR RFLP method has a high discriminative power. Considering the three endonucleases used in this work, we have obtained a variability of 100% for Z. mellis and Z. rouxii strains and up to 70% for Z. bailii. We have also detected two misidentified Z. mellis strains (CBS 711 and CBS 7412) which have RFLP patterns with a set of bands characteristic of Z. rouxii strains. Sequencing of 26S rDNA D1/D2 domains and the 5.8-ITS rDNA region confirmed these strains as Z. rouxii. The method also groups three certified hybrid strains of Zygosaccharomyces in a separate cluster. Copyright 2010 Elsevier B.V. All rights reserved.

  20. Effects of bovine cytochrome P450 single-nucleotide polymorphism, forage type and body condition on production traits in cattle.

    Science.gov (United States)

    Sales, M A; Larson, M J; Reiter, S T; Brown, A H; Brown, M A; Looper, M L; Coffey, K P; Rosenkrans, C F

    2012-08-01

    Relating single-nucleotide polymorphisms (SNP) to cows with acceptable productivity could benefit cattle breeders in areas where tall fescue is the predominant forage. This study aimed to (i) identify SNPs in bovine cytochrome P450 3A28 (CYP3A28) and (ii) determine the associations between SNP genotype, forage and cow body condition (BC). Genotype (CC, CG or GG) and forage [Kentucky-31 wild-type endophyte-infected tall fescue (KY+) vs. bermudagrass] effects on milk volume and quality were determined in Herd 1 cows (123 cows); in Herd 2 (99 cows), genotype and BC (low vs. moderate) effects on ovarian follicle size, calving date and calving per cent were determined; and in Herd 3 (114 cows), effects of genotype and fescue cultivar [KY+ vs. non-toxic endophyte-infected tall fescue (HiMag4)] were related to calving per cent, calving date and weaning weights of both cow and her calf. A cytosine (C) to guanine (G) transversion at base 994 (C994G) in CYP3A28 was identified. There was a genotype × forage type interaction (p productivity in cows. © 2011 Blackwell Verlag GmbH.

  1. A Single Bout of High-Intensity Interval Training Reduces Awareness of Subsequent Hypoglycemia in Patients With Type 1 Diabetes.

    Science.gov (United States)

    Rooijackers, Hanne M; Wiegers, Evita C; van der Graaf, Marinette; Thijssen, Dick H; Kessels, Roy P C; Tack, Cees J; de Galan, Bastiaan E

    2017-07-01

    High-intensity interval training (HIIT) has gained increasing popularity in patients with diabetes. HIIT acutely increases plasma lactate levels. This may be important, since the administration of lactate during hypoglycemia suppresses symptoms and counterregulation while preserving cognitive function. We tested the hypothesis that, in the short term, HIIT reduces awareness of hypoglycemia and attenuates hypoglycemia-induced cognitive dysfunction. In a randomized crossover trial, patients with type 1 diabetes and normal awareness of hypoglycemia (NAH), patients with impaired awareness of hypoglycemia (IAH), and healthy participants ( n = 10 per group) underwent a hyperinsulinemic-hypoglycemic (2.6 mmol/L) clamp, either after a HIIT session or after seated rest. Compared with rest, HIIT reduced symptoms of hypoglycemia in patients with NAH but not in healthy participants or patients with IAH. HIIT attenuated hypoglycemia-induced cognitive dysfunction, which was mainly driven by changes in the NAH subgroup. HIIT suppressed cortisol and growth hormone responses, but not catecholamine responses to hypoglycemia. The present findings demonstrate that a single HIIT session rapidly reduces awareness of subsequent hypoglycemia in patients with type 1 diabetes and NAH, but does not in patients with IAH, and attenuates hypoglycemia-induced cognitive dysfunction. The role of exercise-induced lactate in mediating these effects, potentially serving as an alternative fuel for the brain, should be further explored. © 2017 by the American Diabetes Association.

  2. A new type of FCT martensite phase in single-crystalline Fe{sub 3}Pt Invar alloy

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, Masataka; Sekida, Sayaka [Department of Materials Science and Engineering, Graduate School of Engineering, Osaka University, 2-1 Yamada-oka, Suita, Osaka 565-0871 (Japan); Fukuda, Takashi, E-mail: fukuda@mat.eng.osaka-u.ac.jp [Department of Materials Science and Engineering, Graduate School of Engineering, Osaka University, 2-1 Yamada-oka, Suita, Osaka 565-0871 (Japan); Kakeshita, Tomoyuki [Department of Materials Science and Engineering, Graduate School of Engineering, Osaka University, 2-1 Yamada-oka, Suita, Osaka 565-0871 (Japan); Takahashi, Kohki; Koyama, Keiichi; Nojiri, Hiroyuki [High-Field Laboratory for Superconducting Materials, Institute for Materials Research, Tohoku University, 2-1-1 Sendai Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan)

    2011-08-25

    Highlights: {center_dot} TEM observations at room temperature reveal that the specimen is a single phase of L1{sub 2}-type structure. {center_dot} The spontaneous magnetization and magnetic susceptibility curves of Fe{sub 3}Pt with S = 0.88 have bend points at 60 K. {center_dot} XRD measurements reveal that this alloy exhibits a martensitic transformation to FCT and the transformation temperature is 60 K. {center_dot} The tetragonality c/a is larger than unity in the FCT martensite. {center_dot} This tetragonality is in contrast to the tetragonality c/a < 1generally observed in the FCT martensite with S < 0.8. - Abstract: Martensitic transformation in a highly ordered Fe{sub 3}Pt has been investigated by magnetization and X-ray diffraction measurements. We confirmed that a new type of face-centered tetragonal (FCT) martensite phase appears below 60 K in Fe{sub 3}Pt with a degree of order S = 0.88. The tetragonality c/a gradually increases with decreasing temperature, and is approximately 1.005 at 10 K. This is in contrast to the tetragonality c/a < 1 generally observed in the FCT martensite with a degree of order less than 0.8. The spontaneous magnetization increases in association with the transformation.

  3. Biomaterial based novel polyurethane adhesives for wood to wood and metal to metal bonding

    Directory of Open Access Journals (Sweden)

    Mitesh Ramanlal Patel

    2009-01-01

    Full Text Available Polyurethane adhesives made from synthetic chemicals are non-biodegradable, costly and difficult to find raw materials from local market. To avoid solid pollution problem, cost effectiveness and easy availability of raw materials, biomaterials based polyurethane adhesives are used in current industrial interest. Direct use of castor oil in polyurethane adhesive gives limited hardness. Modification on active sites of castor oil to utilize double bond of unsaturated fatty acid and carboxyl group yields new modified or activated polyols, which can be utilized for polyurethane adhesive formulation. In view of this, we have synthesized polyurethane adhesives from polyester polyols, castor oil based polyols and epoxy based polyols with Isocyanate adducts based on castor oil and trimethylolpropane. To study the effects of polyurethane adhesive strength (i.e. lap shear strength on wood-to-wood and metal-to-metal bonding through various types of polyols, cross-linking density, isocyanate adducts and also to compare adhesive strength between wood to wood and metal to metal surface. These polyols and polyurethanes were characterized through GPC, NMR and IR-spectroscopy, gel and surface drying time. Thermal stability of PU adhesives was determined under the effect of cross-linking density (NCO/OH ratio. The NCO/OH ratio (1.5 was optimized for adhesives as the higher NCO/OH ratio (2.0 increasing cross-linking density and decreases adhesion. Lower NCO/OH ratio (1.0 provideslow cross-linking density and low strength of adhesives.

  4. Novel method for pairing wood samples in choice tests.

    Directory of Open Access Journals (Sweden)

    Sebastian Oberst

    Full Text Available Choice tests are a standard method to determine preferences in bio-assays, e.g. for food types and food additives such as bait attractants and toxicants. Choice between food additives can be determined only when the food substrate is sufficiently homogeneous. This is difficult to achieve for wood eating organisms as wood is a highly variable biological material, even within a tree species due to the age of the tree (e.g. sapwood vs. heartwood, and components therein (sugar, starch, cellulose and lignin. The current practice to minimise variation is to use wood from the same tree, yet the variation can still be large and the quantity of wood from one tree may be insufficient. We used wood samples of identical volume from multiple sources, measured three physical properties (dry weight, moisture absorption and reflected light intensity, then ranked and clustered the samples using fuzzy c-means clustering. A reverse analysis of the clustered samples found a high correlation between their physical properties and their source of origin. This suggested approach allows a quantifiable, consistent, repeatable, simple and quick method to maximize control over similarity of wood used in choice tests.

  5. Application of AERONET Single Scattering Albedo and Absorption Angstrom Exponent to Classify Dominant Aerosol Types during DRAGON Campaigns

    Science.gov (United States)

    Giles, D. M.; Holben, B. N.; Eck, T. F.; Schafer, J.; Crawford, J. H.; Kim, J.; Sano, I.; Liew, S.; Salinas Cortijo, S. V.; Chew, B. N.; Lim, H.; Smirnov, A.; Sorokin, M.; Kenny, P.; Slutsker, I.

    2013-12-01

    Aerosols can have major implications on human health by inducing respiratory diseases due to inhalation of fine particles from biomass burning smoke or industrial pollution and on radiative forcing whereby the presence of absorbing aerosol particles (e.g., black carbon) increases atmospheric heating. Aerosol classification techniques have utilized aerosol loading and aerosol properties derived from multi-spectral and multi-angle observations by ground-based (e.g., AERONET) and satellite instrumentation (e.g., MISR). Aerosol Robotic Network (AERONET) data have been utilized to determine aerosol types by implementing various combinations of measured aerosol optical depth or retrieved size and absorption aerosol properties (e.g., Gobbi et al., 2007; Russell et al., 2010). Giles et al. [2012] showed single scattering albedo (SSA) relationship with extinction Angstrom exponent (EAE) can provide an estimate of the general classification of dominant aerosol types (i.e., desert dust, urban/industrial pollution, biomass burning smoke, and mixtures) based on data from ~20 AERONET sites located in known aerosol source regions. In addition, the absorption Angstrom exponent relationship with EAE can provide an indication of the dominant absorbing aerosol type such as dust, black carbon, brown carbon, or mixtures of them. These classification techniques are applied to the AERONET Level 2.0 quality assured data sets collected during Distributed Regional Aerosol Gridded Observational Network (DRAGON) campaigns in Maryland (USA), Japan, South Korea, Singapore, Penang (Malaysia), and California (USA). An analysis of aerosol type classification for DRAGON sites is performed as well as an assessment of the spatial variability of the aerosol types for selected DRAGON campaigns. Giles, D. M., B. N. Holben, T. F. Eck, A. Sinyuk, A. Smirnov, I. Slutsker, R. R. Dickerson, A. M. Thompson, and J. S. Schafer (2012), An analysis of AERONET aerosol absorption properties and classifications

  6. Wood power in North Carolina

    Energy Technology Data Exchange (ETDEWEB)

    Cleland, J.G.; Guessous, L. [Research Triangle Institute, Research Triangle Park, NC (United States)

    1993-12-31

    North Carolina (NC) is one of the most forested states, and supports a major wood products industry. The NC Department of Natural Resources sponsored a study by Research Triangle Institute to examine new, productive uses of the State`s wood resources, especially electric power generation by co-firing with coal. This paper summarizes our research of the main factors influencing wood power generation opportunities, i.e., (1) electricity demand; (2) initiative and experience of developers; (3) available fuel resources; (4) incentives for alternate fuels; and (5) power plant technology and economics. The results cover NC forests, short rotation woody crops, existing wood energy facilities, electrical power requirements, and environmental regulations/incentives. Quantitative assessments are based on the interests of government agencies, utilities, electric cooperatives, developers and independent power producers, forest products industries, and the general public. Several specific, new opportunities for wood-to-electricity in the State are identified and described. Comparisons are made with nationwide resources and wood energy operations. Preferred approaches in NC are co-generation in existing or modified boilers and in dedicated wood power plants in forest industry regions. Co-firing is mainly an option for supplementing unreliable primary fuel supplies to existing boilers.

  7. Cooling of wood briquettes

    Directory of Open Access Journals (Sweden)

    Adžić Miroljub M.

    2013-01-01

    Full Text Available This paper is concerned with the experimental research of surface temperature of wood briquettes during cooling phase along the cooling line. The cooling phase is an important part of the briquette production technology. It should be performed with care, otherwise the quality of briquettes could deteriorate and possible changes of combustion characteristics of briquettes could happen. The briquette surface temperature was measured with an IR camera and a surface temperature probe at 42 sections. It was found that the temperature of briquette surface dropped from 68 to 34°C after 7 minutes spent at the cooling line. The temperature at the center of briquette, during the 6 hour storage, decreased to 38°C.

  8. Isolated single coronary artery (RII-B type presenting as an inferior wall myocardial infarction: A rare clinical entity

    Directory of Open Access Journals (Sweden)

    Ankur C. Thummar

    2014-09-01

    Full Text Available Isolated single coronary artery without other congenital cardiac anomalies is very rare among the different variations of anomalous coronary patterns. The prognosis in patients with single coronary varies according to the anatomic distribution and associated coronary atherosclerosis. If the left main coronary artery travels between the aorta and pulmonary arteries, it may be a cause of sudden cardiac death. We present multimodality images of a single coronary artery, in which the whole coronary system originated by a single trunk from the right sinus of Valsalva with inter-arterial course of left main coronary artery. This rare type of single coronary artery was classified as RII-B type according to Lipton's scheme of classification. A significant flow-limiting lesions were found in the right coronary artery that was successfully treated with percutaneous coronary intervention.

  9. Pharmacokinetics and pharmacodynamics of saruplase, an unglycosylated single-chain urokinase-type plasminogen activator, in patients with acute myocardial infarction

    NARCIS (Netherlands)

    Koster, R. W.; Cohen, A. F.; Hopkins, G. R.; Beier, H.; Günzler, W. A.; van der Wouw, P. A.

    1994-01-01

    We examined in patients with acute myocardial infarction (AMI) the pharmacokinetics of saruplase, an unglycosylated, single chain, urokinase-type plasminogen activator (rscu-PA) by measuring urokinase-type plasminogen activator (u-PA) antigen and total u-PA activity, its conversion to active

  10. Wood would burn

    International Nuclear Information System (INIS)

    Swithenbank, Jim; Chen, Qun; Zhang, Xiaohui; Sharifi, Vida; Pourkashanian, Mohamed

    2011-01-01

    Absract: In view of the world-wide problem of energy sustainability and greenhouse gas production (carbon dioxide), it is timely to review the issues involved in generating heat and power from all fuels and especially new (to the UK) solid fuels, including high moisture fuels such as wood, SRF, oil shale, tar sands and brown coal, which will become major international fuels as oil and gas become depleted. The combustion properties of some of these materials are significantly different from traditional coal, oil and gas fuels, however the technology proposed herein is also applicable to these conventional fuels. This paper presents some innovative combustion system options and the associated technical factors that must be considered for their implementation. For clarity of understanding, the novel concepts will be largely presented in terms of a currently developing solid fuel market; biomass wood chips. One of the most important characteristics of many solid fuels to be used in the future (including oil shale and brown coal) is their high moisture content of up to 60%. This could be removed by utilising low grade waste heat that is widely available in industry to dry the fuel and thus reduce transport costs. Burning such dried wood for power generation also increases the energy available from combustion and thus acts as a thermal transformer by upgrading the low grade heat to heat available at combustion temperatures. The alternative approach presented here is to recover the latent heat by condensing the extrinsic moisture and the water formed during combustion. For atmospheric combustion, the temperature of the condensed combustion products is below the dew point at about 55-65 o C and is only suitable for recovery in an efficient district heating system. However, in order to generate power from the latent heat, the condensation temperature must be increased to the level where the heat can be used in the thermodynamic power cycle. This can be achieved by

  11. Torrefaction of wood pellets: New solutions

    Science.gov (United States)

    Zaichenko, V. M.; Shterenberg, V. Ya.

    2017-10-01

    The current state of the market of conventional and torrefied wood pellets and the trends of its development have been analyzed. The advantages and disadvantages of pellets of both types have been compared with other alternative fuels. The consumer segment in which wood pellets are the most competitive has been determined. The original torrefaction technology using exhaust gas heat from a standard gas engine that was developed at the Joint Institute for High Technologies and the scheme of an experimental unit for the elaboration of the technology have been presented. The scheme of the combined operation of a torrefaction unit and a standard hot water boiler, which makes it possible to utilize the heat of exhaust steam-and-gas products of torrefaction with the simultaneous prevention of emissions of harmful substances into the environment, has been proposed. The required correlation between the capacity of the torrefaction unit and the heating boiler house has been estimated for optimal operation under the conditions of the isolated urban village in a region that is distant from the areas of extraction of traditional fuels and, at the same time, has quite sufficient resources of raw materials for the production of wood pellets.

  12. The Carbon Impacts of Wood Products

    Science.gov (United States)

    Richard Bergman; Maureen Puettmann; Adam Taylor; Kenneth E. Skog

    2014-01-01

    Wood products have many environmental advantages over nonwood alternatives. Documenting and publicizing these merits helps the future competitiveness of wood when climate change impacts are being considered. The manufacture of wood products requires less fossil fuel than nonwood alternative building materials such as concrete, metals, or plastics. By nature, wood is...

  13. Moisture relations and physical properties of wood

    Science.gov (United States)

    Samuel V. Glass; Samuel L. Zelinka

    2010-01-01

    Wood, like many natural materials, is hygroscopic; it takes on moisture from the surrounding environment. Moisture exchange between wood and air depends on the relative humidity and temperature of the air and the current amount of water in the wood. This moisture relationship has an important influence on wood properties and performance. Many of the challenges of using...

  14. Wood Flour Moulding Technology: Implications for Technical ...

    African Journals Online (AJOL)

    User

    2011-04-19

    Apr 19, 2011 ... selected dry wood by grinding. Interest in this modern industrial practice in wood anchors ... flour moulding technology minimizes atmospheric pollution, reduces cost of wood waste disposal and curbs, ... Zhang and Wolcott,. 2007). Wood Flour Moulding Technology: Implications for Technical Education ...

  15. Fire Safety Design of Wood Structures

    DEFF Research Database (Denmark)

    Hertz, Kristian Dahl

    2006-01-01

    Lecture Notes on Fire Safety Design of Wood Structures including charring of wood and load bearing capacity of beams, columns, and connections.......Lecture Notes on Fire Safety Design of Wood Structures including charring of wood and load bearing capacity of beams, columns, and connections....

  16. Wood-based composites and panel products

    Science.gov (United States)

    John A. Youngquist

    1999-01-01

    Because wood properties vary among species, between trees of the same species, and between pieces from the same tree, solid wood cannot match reconstituted wood in the range of properties that can be controlled in processing. When processing variables are properly selected, the end result can sometimes surpass nature’s best effort. With solid wood, changes in...

  17. Wood Technology: Techniques, Processes, and Products

    Science.gov (United States)

    Oatman, Olan

    1975-01-01

    Seven areas of wood technology illustrates applicable techniques, processes, and products for an industrial arts woodworking curriculum. They are: wood lamination; PEG (polyethylene glycol) diffusion processes; wood flour and/or particle molding; production product of industry; WPC (wood-plastic-composition) process; residential construction; and…

  18. FIRE INSURANCE AND WOOD SCHOOL BUILDINGS.

    Science.gov (United States)

    PURCELL, FRANK X.

    A COMPARISON OF FIRE INSURANCE COSTS OF WOOD, MASONRY, STEEL AND CONCRETE STRUCTURES SHOWS FIRE INSURANCE PREMIMUMS ON WOOD STRUCTURES TEND TO BE HIGHER THAN PREMIUMS ON MASONRY, STEEL AND CONCRETE BUILDINGS, HOWEVER, THE INITIAL COST OF THE WOOD BUILDINGS IS LOWER. DATA SHOW THAT THE SAVINGS ACHIEVED IN THE INITIAL COST OF WOOD STRUCTURES OFFSET…

  19. The challenge of bonding treated wood

    Science.gov (United States)

    Charles R. Frihart

    2004-01-01

    Wood products are quite durable if exposure to moisture is minimized; however, most uses of wood involve considerable exposure to moisture. To preserve the wood, chemicals are used to minimize moisture pickup, to prevent insect attack, and/or to resist microbial growth. The chemicals used as preservatives can interfere with adhesive bonds to wood. Given the many...

  20. Combustion properties of wood impregnated with commercial ...

    African Journals Online (AJOL)

    ajl yemi

    2011-12-19

    Dec 19, 2011 ... ... thermal conductivity and the fact that wood char is formed when wood is burned. In order to reduce flammability and provide safety, wood is treated with fire-retardant chemicals. In other words, the combustibility of wood may be reduced with flame- retardant or fire-retardant materials (Nussbaum, 1988;.

  1. Potential wood protection strategies using physiological requirements of wood degrading fungi

    NARCIS (Netherlands)

    Sailer, M.F.; Etten, B.D. van

    2004-01-01

    Due to the increasing restrictions in the use of wood preserving biocides a number of potential biocide free wood preserving alternatives are currently assessed. Wood degrading fungi require certain conditions in the wood in order to be able to use wood as a food source. This paper discusses the

  2. Characteristics and utilization of non-wood pulp and paper; Himokuzai pulp / kami no tokucho to sono riyo

    Energy Technology Data Exchange (ETDEWEB)

    Hara, H. [Mishima Paper Co. Ltd., Shizuoka (Japan)

    1998-09-01

    The reasons, difficulty in the usage, and the methods of use of non-wood papers are discussed. Non-wood papers sold in Japan are arranged basing on published data. The type of non-wood paper classified as special printing paper makes up the majority, and there are a variety of other products such as printing board, coated paper, thin paper, wrapping paper, functional paper, and watercolor paper. Kenaf and cotton are used in large quantities as non-wood plants for paper production, and use of bagasse and bamboo is increasing. Non-wood paper are used in consideration of environmental and resources problems and for utilizing the special features of non-wood fiber, and the characteristics of non-wood pulp and the effect of non-wood paper are discussed in this report. It is expected that papers utilizing the characteristics of non-wood paper will be developed. Non-wood papers are substitutions for various papers produced from wood pulp, and the fundamental point is the method of improving the original quality and paper quality by combining with non-wood pulp. 11 refs., 4 figs., 3 tabs.

  3. COMBUSTION PROPERTIES OF EUCALYPTUS WOOD

    Directory of Open Access Journals (Sweden)

    Yalçın ÖRS

    1999-03-01

    Full Text Available In this study, the combustion properties of some impregnation materials (abiotic and biotic factors used for eucalyptus wood in interior or exterior environments were investigated. The experimental samples were prepared from Eucalyptus wood based on ASTM-D-1413-76 Tanalith-CBC, boric acid, borax, vacsol-WR, immersol-WR, polyethylen glycole-400 and ammonium sulphate were used as an impregnation material. The results indicated that, vacuum treatment on Eucalyptus gave the lowest retention value of salts. Compounds containing boron+salt increased fire resistance however water repellents decreased the wood flammability.

  4. Catalytic combustion in small wood burning appliances

    Energy Technology Data Exchange (ETDEWEB)

    Oravainen, H. [VTT Energy, Jyvaeskylae (Finland)

    1996-12-31

    There is over a million hand fired small heating appliances in Finland where about 5,4 million cubic meters of wood fuel is used. Combustion in such heating appliances is a batch-type process. In early stages of combustion when volatiles are burned, the formation of carbon monoxide (CO) and other combustible gases are difficult to avoid when using fuels that have high volatile matter content. Harmful emissions are formed mostly after each fuel adding but also during char burnout period. When the CO-content in flue gases is, say over 0.5 %, also other harmful emissions will be formed. Methane (CH{sub 4}) and other hydrocarbons are released and the amount of polycyclic aromatic hydrocarbons (PAH)-compounds can be remarkable. Some PAH-compounds are very carcinogenic. It has been estimated that in Finland even more than 90 % of hydrocarbon and PAH emissions are due to small scale wood combustion. Emissions from transportation is excluded from these figures. That is why wood combustion has a net effect on greenhouse gas phenomena. For example carbon monoxide emissions from small scale wood combustion are two fold compared to that of energy production in power plants. Methane emission is of the same order as emission from transportation and seven fold compared with those of energy production. Emissions from small heating appliances can be reduced by developing the combustion techniques, but also by using other means, for example catalytic converters. In certain stages of the batch combustion, temperature is not high enough, gas mixing is not good enough and residence time is too short for complete combustion. When placed to a suitable place inside a heating appliance, a catalytic converter can oxidize unburned gases in the flue gas into compounds that are not harmful to the environment. (3 refs.)

  5. Willow wood production on radionuclide polluted areas

    Directory of Open Access Journals (Sweden)

    Rodkin Oleg I.

    2010-01-01

    Full Text Available ABSTRACT: One of the key environmental problems in Belarus is effective use of agricultural lands contaminated by radionuclide due to the Chernobyl disaster. The alternative method to traditional agricultural crops is fast growing willow cultivation. It is possible to use biomass of willow as renewable energy source. The goal of our investigation was the estimation of environmental aspects of willow wood production on polluted areas. The field study experiments (2007-2010 were conducted at Krichev district of Mogilev region in eastern Belarus. This region characterized by high level of Cs-137 contamination as well as high level of heavy metals pollution. In the first stage of experiments, the concentration of cesium-137 in different parts of willow biomass had been measured and transfer factor calculated. The measuring had been done for leaves, roots, and wood. To control cesium-137 accumulation in willow biomass we apply different types (nitrogen N, phosphorus P and potassium K and dose of fertilizer. The experiments show that potassium mineral fertilizer is the key factor for radionuclide accumulation control. The optimal dose of potassium is 90 kg per hectare. On the base of experimental results the model of cesium-137 accumulation in the wood for a 21 year has been developed. In accordance with calculation to the end of willow cultivation (21 year concentration of cesium-137 in wood will not be higher than permitted even with the level of cesium-137 contamination in the soil 1480 kBq/m2 (maximum 140 kqB/m2 with permitted level for firewood is 740 Bq/kg.. The concentration of cesium-137 in the roots increases gradually and get maximum in 21 year (3000 kqB/m2. Our results confirm that in the sum about 0.8 million hectares of radionuclide polluted arable lands partly excluded from agricultural practice in Belarus could be used for willow biomass production.

  6. Flume experiments on scour downstream of wood stream restoration structures

    Science.gov (United States)

    Pagliara, Stefano; Kurdistani, Sahameddin Mahmoudi

    2017-02-01

    River restoration aims to improve physical natural form and processes of a river. Techniques to control the riverbed, stabilize channel alignment, protect stream banks, and rebuild the natural habitat are an important part of river restoration projects. Rivers can be stabilized and habitat restored through techniques such as rebuilding meanders and pool-riffle sequences and managing large wood. Structures that limit channel width to accelerate the normal flows through the constricted section are referred to as stream deflectors. Single-wing, double-wing and triangular deflectors are the most commonly used types of this measure. Log-frame deflectors consist of a triangular log frame filled with rock. Deflector constructions singly or in series in low gradient meandering streams, divert base flows toward the center of the channel and, under certain conditions, increase the depth and velocity of flow thereby creating scour pools and enhancing fish habitat. Scour characteristics and morphologies downstream of log-frame deflectors have been analyzed at the hydraulic laboratory of the University of Pisa. All experiments have been carried out in clear water conditions. The results showed that the tailwater depth plays an important role on scour characteristics. In addition, it was experimentally proven that using log-frame deflectors instead of log-deflectors result in a better river bank protection. In this case, for all the tested hydraulic conditions, the scour hole never occurred close to the channel bank. Useful empirical relationships have been proposed in order to evaluate the main features of the scour geometry.

  7. Wood decay by Chlorociboria aeruginascens (Nyl.) Kanouse (Helotiales, Leotiaceae) and associated basidiomycete fungi

    Science.gov (United States)

    Dana L. Richter; Jessie A. Glaeser

    2015-01-01

    Two isolates of Chlorociboria aeruginascens (Nyl.) Kanouse incubated axenically on aspen wood blocks resulted in 18% and 32% mass loss after 134 wks (2 yrs 8 mo). Aspen wood decayed by C. aeruginascens contained cavities in the S2 layer of the secondary cell wall, similar to Type I soft rot attack, as well as erosion troughs and...

  8. The properties of the wood-polystyrene interphase determined by inverse gas chromatography

    Science.gov (United States)

    John Simonsen; Zhenqiu Hong; Timothy G. Rials

    1997-01-01

    The properties of the interphase in wood-polymer composites are important determinants of the properties of the final composite. This study used inverse gas chromatography (IGC) to measure interphasal properties of composites of polystyrene and two types of wood fiber fillers and an inoranic substrate (CW) with varying amounts of surface coverage of polystyrene. Glass...

  9. Finite element modeling of small-scale tapered wood-laminated composite poles with biomimicry features

    Science.gov (United States)

    Cheng Piao; Todd F. Shupe; R.C. Tang; Chung Y. Hse

    2008-01-01

    Tapered composite poles with biomimicry features as in bamboo are a new generation of wood laminated composite poles that may some day be considered as an alternative to solid wood poles that are widely used in the transmission and telecommunication fields. Five finite element models were developed with ANSYS to predict and assess the performance of five types of...

  10. Understanding decay resistance, dimensional stability and strength changes in heat treated and acetylated wood

    Science.gov (United States)

    Roger M. Rowell; Rebecca E. Ibach; James McSweeny; Thomas Nilsson

    2009-01-01

    Reductions in hygroscopicity, increased dimensional stability and decay resistance of heat-treated wood depend on decomposition of a large portion of the hemicelluloses in the wood cell wall. In theory, these hemicelluloses are converted to small organic molecules, water and volatile furan-type intermediates that can polymerize in the cell wall. Reductions in...

  11. Effect of simulated rainfall and weathering on release of preservative elements from CCA treated wood

    Science.gov (United States)

    Stan Lebow; R. Sam Williams; Patricia Lebow

    2003-01-01

    The release of arsenic from wood pressure-treated with chromated copper arsenate (CCA) can be decreased by application of wood finishes, but little is known about the types of finishes that are best suited for this purpose. This study evaluated the effects of finish water repellent content and ultraviolet (UV) radiation on the release of arsenic, copper, and chromium...

  12. Guide for minimizing the effect of preservative-treated wood on sensitive environments

    Science.gov (United States)

    Stan T. Lebow; Michael Tippie

    2001-01-01

    Preservative-treated wood is often used for construction of highway and foot bridges, wetland boardwalks, and other structures in or over water or sensitive environments. In these applications it is important that release of preservative from the wood into the environment is minimized. This publication addresses this concern by describing the various types of pressure-...

  13. Online resources for the identification of North American wood decay fungi

    Science.gov (United States)

    Jessie A. Glaeser

    2012-01-01

    The ability to identify wood decay fungi is an important skill for an arborist. Knowing which fungus is colonizing a tree can be used to better assess the type, amount, and position of decay in the tree, and its subsequent effects on wood strength. Distinguishing species of fungi that colonize sapwood, heartwood, or roots can provide information to improve the quality...

  14. Process methods and levels of automation of wood pallet repair in the United States

    Science.gov (United States)

    Jonghun Park; Laszlo Horvath; Robert J. Bush

    2016-01-01

    This study documented the current status of wood pallet repair in the United States by identifying the types of processing and equipment usage in repair operations from an automation prespective. The wood pallet repair firms included in the sudy received an average of approximately 1.28 million cores (i.e., used pallets) for recovery in 2012. A majority of the cores...

  15. Wood Ash Induced pH Changes Strongly Affect Soil Bacterial Numbers and Community Composition.

    Science.gov (United States)

    Bang-Andreasen, Toke; Nielsen, Jeppe T; Voriskova, Jana; Heise, Janine; Rønn, Regin; Kjøller, Rasmus; Hansen, Hans C B; Jacobsen, Carsten S

    2017-01-01

    Recirculation of wood ash from energy production to forest soil improves the sustainability of this energy production form as recycled wood ash contains nutrients that otherwise would be lost at harvest. In addition, wood-ash is beneficial to many soils due to its inherent acid-neutralizing capabilities. However, wood ash has several ecosystem-perturbing effects like increased soil pH and pore water electrical conductivity both known to strongly impact soil bacterial numbers and community composition. Studies investigating soil bacterial community responses to wood ash application remain sparse and the available results are ambiguous and remain at a general taxonomic level. Here we investigate the response of bacterial communities in a spruce forest soil to wood ash addition corresponding to 0, 5, 22, and 167 t wood ash ha -1 . We used culture-based enumerations of general bacteria, Pseudomonas and sporeforming bacteria combined with 16S rRNA gene amplicon sequencing to valuate soil bacterial responses to wood ash application. Results showed that wood ash addition strongly increased soil pH and electrical conductivity. Soil pH increased from acidic through neutral at 22 t ha -1 to alkaline at 167 t ha -1 . Bacterial numbers significantly increased up to a wood ash dose of 22 t ha -1 followed by significant decrease at 167 t ha -1 wood ash. The soil bacterial community composition changed after wood ash application with copiotrophic bacteria responding positively up to a wood ash dose of 22 t ha -1 while the adverse effect was seen for oligotrophic bacteria. Marked changes in bacterial community composition occurred at a wood ash dose of 167 t ha -1 with a single alkaliphilic genus dominating. Additionally, spore-formers became abundant at an ash dose of 167 t ha -1 whereas this was not the case at lower ash doses. Lastly, bacterial richness and diversity strongly decreased with increasing amount of wood ash applied. All of the observed bacterial responses can be

  16. Factors associated with anxiety and depression among type 2 diabetes outpatients in Malaysia: a descriptive cross-sectional single-centre study

    OpenAIRE

    Ganasegeran, Kurubaran; Renganathan, Pukunan; Manaf, Rizal Abdul; Al-Dubai, Sami Abdo Radman

    2014-01-01

    Objective To determine the prevalence and factors associated with anxiety and depression among type 2 diabetes outpatients in Malaysia. Design Descriptive, cross-sectional single-centre study with universal sampling of all patients with type 2 diabetes. Setting Endocrinology clinic of medical outpatient department in a Malaysian public hospital. Participants All 169 patients with type 2 diabetes (men, n=99; women, n=70) aged between 18 and 90 years who acquired follow-up treatment from the en...

  17. Moisture Distribution and Flow During Drying of Wood and Fiber

    Energy Technology Data Exchange (ETDEWEB)

    Zink-Sharp, Audrey; Hanna, Robert B.

    2001-12-28

    New understanding, theories, and techniques for moisture flow and distribution were developed in this research on wood and wood fiber. Improved understanding of the mechanisms of flake drying has been provided. Observations of flake drying and drying rate curves revealed that rate of moisture loss consisted of two falling rate periods and no constant rate drying period was observed. Convective heat transfer controls the first period, and bound water diffusion controls the second period. Influence of lower drying temperatures on bending properties of wood flakes was investigated. Drying temperature was found to have a significant influence on bending stiffness and strength. A worksheet for calculation of the energy required to dry a single strandboard flake was developed but has not been tested in an industrial setting yet. A more complete understanding of anisotropic transverse shrinkage of wood is proposed based on test results and statistical analysis. A simplified mod el of a wood cell's cross-section was drawn for calculating differential transverse shrinkage. The model utilizes cell wall thickness and microfibrillar packing density and orientation. In spite of some phenomena of cell wall structure not yet understood completely, the results might explain anisotropic transverse shrinkage to a major extent. Boundary layer theory was found useful for evaluating external moisture resistance during drying. Simulated moisture gradients were quire comparable to the actual gradients in dried wood. A mathematical procedure for determining diffusion and surface emission coefficients was also developed. Thermal conductivity models of wood derived from its anatomical structure were created and tested against experimental values. Model estimations provide insights into changes in heat transfer parameters during drying. Two new techniques for measuring moisture gradients created in wood during drying were developed. A new technique that utilizes optical properties of

  18. Women's work... in wood products

    Science.gov (United States)

    Janice K. Wiedenbeck

    1998-01-01

    Women have opportunities galore in the 1990s in wood products research, education, extension, consulting,manufacturing, marketing, and associations in North America. In the 1980s the same statement could not have been made.

  19. Wood and Paper Manufacturing Sectors

    Science.gov (United States)

    Find EPA regulatory information for the wood product and paper manufacturing sectors, including paper, pulp and lumber. Information includes NESHAPs and effluent guidelines for pulp and paper rulemaking, and compliance guidelines

  20. Wood-burning stoves worldwide

    DEFF Research Database (Denmark)

    Luis Teles de Carvalho, Ricardo

    were suggested to facilitate the transition to cleaner wood-burning regimes. Considering that 40% of the world population continues relying on traditional forms of wood-burning, the design and dissemination of cleaner technologies of WBSs constitute relevant strategies to mitigate global climate...... of improved stoves. In the Brazilian case study, it was observed that the kitchen concentrations of PM2.5 monitored during wood cooking events increased by more than 10 times in relation to the background levels due to the improper use and maintenance of the studied ICSs (rocket stoves). In Southern Europe...... to facilitate the transition to more intelligent modes of using WBSs by: 1st training solid-fuel users to better operate and maintain existing installations, 2nd harmonizing wood-burning regulations to address the use of seasoned fuels, certified stoves and functioning chimneys; 3rd designing applications...

  1. Oxidative stress in patients with type 1 diabetes mellitus: is it affected by a single bout of prolonged exercise?

    Science.gov (United States)

    Francescato, Maria Pia; Stel, Giuliana; Geat, Mario; Cauci, Sabina

    2014-01-01

    Presently, no clear-cut guidelines are available to suggest the more appropriate physical activity for patients with type 1 diabetes mellitus due to paucity of experimental data obtained under patients' usual life conditions. Accordingly, we explored the oxidative stress levels associated with a prolonged moderate intensity, but fatiguing, exercise performed under usual therapy in patients with type 1 diabetes mellitus and matched healthy controls. Eight patients (4 men, 4 women; 49±11 years; Body Mass Index 25.0±3.2 kg·m(-2); HbA1c 57±10 mmol·mol(-1)) and 14 controls (8 men, 6 women; 47±11 years; Body Mass Index 24.3±3.3 kg·m(-2)) performed a 3-h walk at 30% of their heart rate reserve. Venous blood samples were obtained before and at the end of the exercise for clinical chemistry analysis and antioxidant capacity. Capillary blood samples were taken at the start and thereafter every 30 min to determine lipid peroxidation. Patients showed higher oxidative stress values as compared to controls (95.9±9.7 vs. 74.1±12.2 mg·L(-1) H2O2; pexercise (p = NS), while oxidative defence increased significantly at the end of exercise (pdiabetes exercising under their usual life conditions (i.e. usual therapy and diet). Specifically, we found that the oxidative stress was not exacerbated due to a single bout of prolonged moderate intensity aerobic exercise, a condition simulating several outdoor leisure time physical activities. Oxidative defence increased in both patients and controls, suggesting beneficial effects of prolonged aerobic fatiguing exercise.

  2. Wood is burning in capital city area's fireplaces as well

    International Nuclear Information System (INIS)

    Luoma, H.

    1998-01-01

    The firewood market situation in the capital city area was examined by a mail questionnaire in the spring of 1997. The questionnaire form was distributed to 800 single-family houses in Espoo, Helsinki and Vantaa. The responses to the questionnaire numbered 297 (37 %). Wood was found to be the main source of heat energy in the households of 2 % of the respondents and as an alternative source of heat energy in 58 % of the households. The most common fireplace in the respondents' homes was a wood-fired sauna stove. Heat-accumulating fireplaces were in the second place and open fireplaces in the third place. The installation of heat-accumulating fireplaces has become more popular while wood-fired sauna stoves and open fireplaces have lost some of their popularity during the past few years. Thirteen percent of the owners responding to the questionnaire intend to install new fireplaces. Half of the respondents were of the opinion that there is nothing to restrict the use of their fireplaces. Those who felt that there were restrictions stated that the high cost of firewood was the most significant restricting factor. Other restricting factors were the difficulty of getting firewood and the shortcomings of wood storage facilities. The storage problem can be dealt with by, for example, resorting to joint purchases, in which case the batch of wood for one house can be smaller in size. One quarter of the interviewers showed interest in concerted purchasing and deliveries of wood. An average of 3.6 m 3 of wood was used in the single-family houses in the capital city area in 1996. This wood was obtained either by purchasing it, from one's own forest/block of land or by some other independent means (not by purchasing). These three forms of acquiring wood were almost equally important. Typically, firewood was bought the form of logging residues. The greatest demand is for bulk batches of chopped firewood. When firewood is purchased, the customer typically prefers to have it

  3. Chemical responses to modified lignin composition in tension wood of hybrid poplar (Populus tremula x Populus alba).

    Science.gov (United States)

    Al-Haddad, Jameel M; Kang, Kyu-Young; Mansfield, Shawn D; Telewski, Frank W

    2013-04-01

    The effect of altering the expression level of the F5H gene was investigated in three wood tissues (normal, opposite and tension wood) in 1-year-old hybrid poplar clone 717 (Populus tremula × Populus alba L.), containing the F5H gene under the control of the C4H promoter. Elevated expression of the F5H gene in poplar has been previously reported to increase the percent syringyl content of lignin. The wild-type and three transgenic lines were inclined 45° for 3 months to induce tension wood formation. Tension and opposite wood from inclined trees, along with normal wood from control trees, were analyzed separately for carbohydrates, lignin, cellulose crystallinity and microfibril angle (MFA). In the wild-type poplar, the lignin in tension wood contained a significantly higher percentage of syringyl than normal wood or opposite wood. However, there was no significant difference in the percent syringyl content of the three wood types within each of the transgenic lines. Increasing the F5H gene expression caused an increase in the percent syringyl content and a slight decrease in the total lignin in normal wood. In tension wood, the addition of a gelatinous layer in the fiber walls resulted in a consistently lower percentage of total lignin in the tissue. Acid-soluble lignin was observed to increase by up to 2.3-fold in the transgenic lines. Compared with normal wood and opposite wood, cell wall crystallinity in tension wood was higher and the MFA was smaller, as expected, with no evidence of an effect from modifying the syringyl monomer ratio. Tension wood in all the lines contained consistently higher total sugar and glucose percentages when compared with normal wood within the respective lines. However, both sugar and glucose percentages were lower in the tension wood of transgenic lines when compared with the tension wood of wild-type trees. Evaluating the response of trees with altered syringyl content to gravity will improve our understanding of the changes

  4. Re-introduction of structurally complex wood jams promotes channel and habitat recovery from overwidening: Implications for river conservation

    OpenAIRE

    Harvey, G.; Henshaw, A.; Parker, C.; Sayer, C.

    2017-01-01

    1. Large wood is a powerful geomorphic agent in rivers, providing important habitat functions for a range of aquatic organisms, but has been subject to a long history of removal.\\ud 2. Internationally, approaches to river restoration are increasingly incorporating large wood features, but generally favour simple flow deflectors (e.g. single logs, stripped of branches and anchored in place) over more complex structures that more accurately mimic natural wood jams.\\ud 3. This paper explores cha...

  5. Conduction band mass determinations for n-type InGaAs/InAlAs single quantum wells

    Energy Technology Data Exchange (ETDEWEB)

    Jones, E.D.; Reno, J.L. [Sandia National Labs., Albuquerque, NM (United States); Kotera, Nobuo [Kyushu Inst. of Tech., Iizuka, Fukuoka (Japan); Wang, Y. [Florida State Univ., Tallahassee, FL (United States). National High Magnetic Field Lab.

    1998-05-01

    The authors report the measurement of the conduction band mass in n-type single 27-ML-wide InGaAs/InAlAs quantum well lattice matched to InP using two methods: (1) Magnetoluminescence spectroscopy and (2) far-infrared cyclotron resonance. The magnetoluminescence method utilizes Landau level transitions between 0 and 14 T at 1.4 K. The far infrared cyclotron resonance measurements were made at 4.2 K and to fields as large up to 18 T. The 2D-carrier density N{sub 2D} = 3 {times} 10{sup 11} cm{sup {minus}2} at low temperatures. The magnetoluminescence technique yielded an effective conduction-band mass of m{sub c} = 0.062m{sub 0} while the far infrared cyclotron resonance measurements gave m{sub c} = 0.056m{sub 0}, where m{sub 0} is the free electron mass. Both measurements show no evidence for any significant conduction-band nonparabolicity.

  6. A Modified Model Reference Adaptive Control for a Single Motor of Latch Type Control Element Drive Mechanism

    International Nuclear Information System (INIS)

    Park, Bae Jeong

    2016-01-01

    A modified Model Reference Adaptive Control (MRAC) for a single motor of latch type Control Element Drive Mechanism (CEDM) is described herein. The CEDM has complicated dynamic characteristics including electrical, mechanical, and magnetic effects. The previous control system has utilized a Proportional-Integral (PI) controller, and the control performance is limited according to nonlinear dynamic characteristics and environmental conditions. The modified MRAC using system identification (ID) technique improves the control performance in the operating condition such as model parameter variation and environmental condition change. The modified MRAC using the identified reference model with feed-forward gain and 180Hz noise reduction filter presents better performance under normal and/or abnormal condition. The simplified reference model can make H/W implementation more practical on the viewpoint of less computation and good performance. Actually, the CEDM controller shall be capable of controlling 101 control element assemblies (CEAs) individually in the nuclear power plant. Because the load conditions and the environmental condition around the 101 CEAs are all different minutely, the proposed modified MRAC can be a good practice. The modified MRAC controller will be applied in the real nuclear power plant later and this will overcome some weak point of PI controller

  7. Factors affecting the performance of a single-chamber microbial fuel cell-type biological oxygen demand sensor.

    Science.gov (United States)

    Yang, Gai-Xiu; Sun, Yong-Ming; Kong, Xiao-Ying; Zhen, Feng; Li, Ying; Li, Lian-Hua; Lei, Ting-Zhou; Yuan, Zhen-Hong; Chen, Guan-Yi

    2013-01-01

    Microbial fuel cells (MFCs) are devices that exploit microorganisms as biocatalysts to degrade organic matter or sludge present in wastewater (WW), and thereby generate electricity. We developed a simple, low-cost single-chamber microbial fuel cell (SCMFC)-type biochemical oxygen demand (BOD) sensor using carbon felt (anode) and activated sludge, and demonstrated its feasibility in the construction of a real-time BOD measurement system. Further, the effects of anodic pH and organic concentration on SCMFC performance were examined, and the correlation between BOD concentration and its response time was analyzed. Our results demonstrated that the SCMFC exhibited a stable voltage after 132 min following the addition of synthetic WW (BOD concentration: 200 mg/L). Notably, the response signal increased with an increase in BOD concentration (range: 5-200 mg/L) and was found to be directly proportional to the substrate concentration. However, at higher BOD concentrations (>120 mg/L) the response signal remained unaltered. Furthermore, we optimized the SCMFC using synthetic WW, and tested it with real WW. Upon feeding real WW, the BOD values exhibited a standard deviation from 2.08 to 8.3% when compared to the standard BOD5 method, thus demonstrating the practical applicability of the developed system to real treatment effluents.

  8. Formaldehyde and acetaldehyde emissions from residential wood combustion in Portugal

    Science.gov (United States)

    Cerqueira, Mário; Gomes, Luís; Tarelho, Luís; Pio, Casimiro

    2013-06-01

    A series of experiments were conducted to characterize formaldehyde and acetaldehyde emissions from residential combustion of common wood species growing in Portugal. Five types of wood were investigated: maritime pine (Pinus pinaster), eucalyptus (Eucalyptus globulus), cork oak (Quercus suber), holm oak (Quercus rotundifolia) and pyrenean oak (Quercus pyrenaica). Laboratory experiments were performed with a typical wood stove used for domestic heating in Portugal and operating under realistic home conditions. Aldehydes were sampled from diluted combustion flue gas using silica cartridges coated with 2,4-dinitrophenylhydrazine and analyzed by high performance liquid chromatography with diode array detection. The average formaldehyde to acetaldehyde concentration ratio (molar basis) in the stove flue gas was in the range of 2.1-2.9. Among the tested wood types, pyrenean oak produced the highest emissions for both formaldehyde and acetaldehyde: 1772 ± 649 and 1110 ± 454 mg kg-1 biomass burned (dry basis), respectively. By contrast, maritime pine produced the lowest emissions: 653 ± 151 and 371 ± 162 mg kg-1 biomass (dry basis) burned, respectively. Aldehydes were sampled separately during distinct periods of the holm oak wood combustion cycles. Significant variations in the flue gas concentrations were found, with higher values measured during the devolatilization stage than in the flaming and smoldering stages.

  9. Mechanical properties evaluation of extruded wood polymer composites

    Science.gov (United States)

    Zaini, A. S. Syah M.; Rus, Anika Zafiah M.; Rahman, Norherman Abdul; Jais, Farhana Hazwanee M.; Fauzan, M. Zarif; Sufian, N. Afiqah

    2017-09-01

    The rapidly expanding of interest in the manufacture of composite materials from waste industrial and agricultural materials is due to high demand for environmentally friendly materials. Wood polymer composite (WPC) are being used in many type of applications such as in the automobile, electronic, aerospace industry and construction. Therefore, this research study is to determine the mechanical properties behaviour of WPC after an extended Ultra Violet (UV) irradiation exposure. The fabricated sample has been used and to be compared in this research is consists of rice husk, waste fibre and polypropylene (PP) with 4 different types of WPC which are wood block waste (WBW), wood block virgin (WBV), wood sheet (WS) and wood sheet waste (WSW). The extruded specimens were tested for mechanical properties such as strength under compression, puncture strength and impact resistance, and density. In addition, the specimen has been irradiated with the UV exposure at 5000 hours, 10000 hours and 15000 hours. Generally, the mechanical properties the WPC which made from the recycled material were lower than the WPC from virgin material but the density was comparable between the two products after UV irradiation exposure.

  10. Oxidative stress in patients with type 1 diabetes mellitus: is it affected by a single bout of prolonged exercise?

    Directory of Open Access Journals (Sweden)

    Maria Pia Francescato

    Full Text Available Presently, no clear-cut guidelines are available to suggest the more appropriate physical activity for patients with type 1 diabetes mellitus due to paucity of experimental data obtained under patients' usual life conditions. Accordingly, we explored the oxidative stress levels associated with a prolonged moderate intensity, but fatiguing, exercise performed under usual therapy in patients with type 1 diabetes mellitus and matched healthy controls. Eight patients (4 men, 4 women; 49±11 years; Body Mass Index 25.0±3.2 kg·m(-2; HbA1c 57±10 mmol·mol(-1 and 14 controls (8 men, 6 women; 47±11 years; Body Mass Index 24.3±3.3 kg·m(-2 performed a 3-h walk at 30% of their heart rate reserve. Venous blood samples were obtained before and at the end of the exercise for clinical chemistry analysis and antioxidant capacity. Capillary blood samples were taken at the start and thereafter every 30 min to determine lipid peroxidation. Patients showed higher oxidative stress values as compared to controls (95.9±9.7 vs. 74.1±12.2 mg·L(-1 H2O2; p<0.001. In both groups, oxidative stress remained constant throughout the exercise (p = NS, while oxidative defence increased significantly at the end of exercise (p<0.02 from 1.16±0.13 to 1.19±0.10 mmol·L(-1 Trolox in patients and from 1.09±0.21 to 1.22±0.14 mmol·L(-1 Trolox in controls, without any significant difference between the two groups. Oxidative stress was positively correlated to HbA1c (p<0.005 and negatively related with uric acid (p<0.005. In conclusion, we were the first to evaluate the oxidative stress in patients with type 1 diabetes exercising under their usual life conditions (i.e. usual therapy and diet. Specifically, we found that the oxidative stress was not exacerbated due to a single bout of prolonged moderate intensity aerobic exercise, a condition simulating several outdoor leisure time physical activities. Oxidative defence increased in both patients and controls, suggesting

  11. A single nucleotide polymorphism within the acetyl-coenzyme A carboxylase beta gene is associated with proteinuria in patients with type 2 diabetes

    DEFF Research Database (Denmark)

    Maeda, Shiro; Kobayashi, Masa-aki; Araki, Shin-ichi

    2010-01-01

    It has been suggested that genetic susceptibility plays an important role in the pathogenesis of diabetic nephropathy. A large-scale genotyping analysis of gene-based single nucleotide polymorphisms (SNPs) in Japanese patients with type 2 diabetes identified the gene encoding acetyl-coenzyme A ca......It has been suggested that genetic susceptibility plays an important role in the pathogenesis of diabetic nephropathy. A large-scale genotyping analysis of gene-based single nucleotide polymorphisms (SNPs) in Japanese patients with type 2 diabetes identified the gene encoding acetyl...... among patients with type 2 diabetes and proteinuria. A meta-analysis revealed that rs2268388 was significantly associated with proteinuria in Japanese patients with type 2 diabetes (p = 5.35 x 10(-8), odds ratio = 1.61, 95% Cl: 1.35-1.91). Rs2268388 was also associated with type 2 diabetes...

  12. UV curable aqueous dispersions for wood coatings

    International Nuclear Information System (INIS)

    Peeters, S.; Bleus, J.P.; Wang, Z.J.; Arceneaux, J. A.; Hall, J.

    1999-01-01

    In this paper the characterisation of aqueous dispersions of UV curable resins is described. Two types of dispersions were used: dispersions that are tacky after water evaporation and tack - free before cure dispersions. The physical and rheological properties of these products have been determined and the performance of these dispersions in various formulations, especially for wood applications has been studied. With these dispersions, it is possible to produce coatings having a good cure speed, good surface hardness and good solvent -, chemical - and water resistance

  13. Regional prices in the Swedish wood-fuel market

    International Nuclear Information System (INIS)

    Hillring, Bengt

    1999-01-01

    This paper analyses, through a statistical survey, the regional distribution of prices on the commercial wood-fuel market for district heating plants and the pellets market for single family houses. The existing market watch of the national Swedish wood-fuel market has been developed for both refined and unrefined wood-fuels. The last five years the trend for wood-fuel prices on the district heating market has been stable, with a slight increase in the price of refined wood-fuels. However, on the young and fast-growing household market for pellets, prices have increased 12% during the last three years. The distribution of prices for northern, middle and southern Sweden indicates differences within 5% between the regions. The limited price difference between Swedish regions are a product of a large domestic supply and an increasing trade among regions in Europe, putting pressure on prices. Regional differences, mirrored as transportation distances and local production costs are key factors that could explain this regional price variation. However, the development of a commercial market with less regulation tends to level out prices. Consumers on the household market purchase small quantities and do not have the same possibility as district heating companies to take advantage of the oversupply opportunity and thus face a faster price development. The weaker market position of the consumers also tends to give homogeneous prices between regions of the residential sector. (Author)

  14. Theoretical and experimental studies on emissions from wood combustion

    Energy Technology Data Exchange (ETDEWEB)

    Skreiberg, Oeyvind

    1997-12-31

    This thesis discusses experiments on emissions from wood log combustion and single wood particle combustion, both caused by incomplete combustion and emissions of nitric and nitrous oxide, together with empirical and kinetic NO{sub x} modelling. Experiments were performed in three different wood stoves: a traditional stove, a staged air stove and a stove equipped with a catalytic afterburner. Ideally, biomass fuel does not give a net contribution to the greenhouse effect. However, incomplete combustion was found to result in significant greenhouse gas emissions. Empirical modelling showed the excess air ratio and the combustion chamber temperature to be the most important input variables controlling the total fuel-N to NO{sub x} conversion factor. As the result of an international round robin test of a wood stove equipped with a catalytic afterburner, particle emission measurements were found to be the best method to evaluate the environmental acceptability of the tested stove, since the particle emission level was least dependent of the national standards, test procedures and calculation procedures used. In batch single wood particle combustion experiments on an electrically heated small-scale fixed bed reactor the fuel-N to NO conversion factor varied between 0.11-0.86 depending on wood species and operating conditions. A parameter study and homogeneous kinetic modelling on a plug flow reactor showed that, depending on the combustion compliance in question, there is an optimum combination of primary excess air ratio, temperature and residence time that gives a maximum conversion of fuel-N to N{sub 2}. 70 refs., 100 figs., 26 tabs.

  15. Contact stresses modeling at the Panda-type fiber single-layer winding and evaluation of their impact on the fiber optic properties

    Science.gov (United States)

    Lesnikova, Yu I.; Smetannikov, O. Yu; Trufanov, A. N.; Trufanov, N. A.

    2017-02-01

    The impact of contact transverse forces on the birefringence of the single-mode polarization-maintaining Panda-type fiber is numerically modeled. It has been established that with a single-row power winding on a cylindrical mandrel, the fiber tension at winding is the principal factor that influences birefringence. When coiling the fiber based on the local defect microbending, the birefringence at the microbending point differs from that of the free fiber by 1.3%.

  16. Association of single nucleotide polymorphisms in TCF2 with type 2 diabetes susceptibility in a Han Chinese population.

    Directory of Open Access Journals (Sweden)

    Xuelong Zhang

    Full Text Available Hepatocyte nuclear factor 1β (HNF1β, a transcription factor encoded by the transcription factor 2 gene (TCF2, plays a critical role in pancreatic cell formation and glucose homeostasis. It has been suggested that single nucleotide polymorphisms (SNPs of TCF2 are associated with susceptibility to type 2 diabetes (T2D. However, published results are inconsistent and inclusive. To further investigate the role of these common variants, we examined the association of TCF2 polymorphisms with the risk of T2D in a Han population in northeastern China. We genotyped five SNPs in 624 T2D patients and 630 healthy controls by using a SNaPshot method, and evaluated the T2D risk conferred by individual SNPs and haplotypes. In the single-locus analysis, we found that rs752010, rs4430796 and rs7501939 showed allelic differences between T2D patients and healthy controls, with an OR of 1.26 (95% CI 1.08-1.51, P = 0.003, an OR of 1.23 (95% CI 1.06-1.55, P = 0.001 and an OR of 1.28 (95% CI 1.10-1.61, P = 0.001, respectively. Genotype association analysis of each locus also revealed that the homozygous carriers of the at-risk allele had a significant increased T2D risk compared to homozygous carriers of the other allele (OR 1.78, 95% CI 1.20-2.64 for rs752010; OR 1.82, 95% CI 1.24-2.67 for rs4430796; OR 1.95, 95% CI 1.31-2.90 for rs7501939, even after Bonferroni correction for multiple comparisons. Besides, the haplotype-based analysis demonstrated that AGT in block rs752010-rs4430796-rs7501939 was associated with about 30% increase in T2D risk (OR 1.31, 95% CI 1.09-1.57, P = 0.01. Our findings suggested that TCF2 variants may be involved in T2D risk in a Han population of northeastern China. Larger studies with ethnically diverse populations are warranted to confirm the results reported in this investigation.

  17. Wood pellets, what else? Greenhouse gas parity times of European electricity from wood pellets produced in the south-eastern United States using different softwood feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Hanssen, Steef V. [Radboud Univ., Nijmegen (Netherlands). Dept. of Environmental Science, Faculty of Science; Utrecht Univ., Utrecht (The Netherlands). Copernicus Inst. of Sustainable Development, Faculty of Geosciences; Duden, Anna S. [Utrecht Univ., Utrecht (The Netherlands). Copernicus Inst. of Sustainable Development, Faculty of Geosciences; Junginger, Martin [Utrecht Univ., Utrecht (The Netherlands). Copernicus Inst. of Sustainable Development, Faculty of Geosciences; Dale, Virginia H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Environmental Sciences Division, Center for BioEnergy Sustainability; van der Hilst, Floor [Utrecht Univ., Utrecht (The Netherlands). Copernicus Inst. of Sustainable Development, Faculty of Geosciences

    2016-12-29

    Several EU countries import wood pellets from the south-eastern United States. The imported wood pellets are (co-)fired in power plants with the aim of reducing overall greenhouse gas (GHG) emissions from electricity and meeting EU renewable energy targets. To assess whether GHG emissions are reduced and on what timescale, we construct the GHG balance of wood-pellet electricity. This GHG balance consists of supply chain and combustion GHG emissions, carbon sequestration during biomass growth, and avoided GHG emissions through replacing fossil electricity. We investigate wood pellets from four softwood feedstock types: small roundwood, commercial thinnings, harvest residues, and mill residues. Per feedstock, the GHG balance of wood-pellet electricity is compared against those of alternative scenarios. Alternative scenarios are combinations of alternative fates of the feedstock material, such as in-forest decomposition, or the production of paper or wood panels like oriented strand board (OSB). Alternative scenario composition depends on feedstock type and local demand for this feedstock. Results indicate that the GHG balance of wood-pellet electricity equals that of alternative scenarios within 0 to 21 years (the GHG parity time), after which wood-pellet electricity has sustained climate benefits. Parity times increase by a maximum of twelve years when varying key variables (emissions associated with paper and panels, soil carbon increase via feedstock decomposition, wood-pellet electricity supply chain emissions) within maximum plausible ranges. Using commercial thinnings, harvest residues or mill residues as feedstock leads to the shortest GHG parity times (0-6 years) and fastest GHG benefits from wood-pellet electricity. Here, we find shorter GHG parity times than previous studies, for we use a novel approach that differentiates feedstocks and considers alternative scenarios based on (combinations of) alternative feedstock fates, rather than on alternative land

  18. Gravitropisms and reaction woods of forest trees - evolution, functions and mechanisms.

    Science.gov (United States)

    Groover, Andrew

    2016-08-01

    Contents 790 I. 790 II. 792 III. 795 IV. 797 V. 798 VI. 800 VII. 800 800 References 800 SUMMARY: The woody stems of trees perceive gravity to determine their orientation, and can produce reaction woods to reinforce or change their position. Together, graviperception and reaction woods play fundamental roles in tree architecture, posture control, and reorientation of stems displaced by wind or other environmental forces. Angiosperms and gymnosperms have evolved strikingly different types of reaction wood. Tension wood of angiosperms creates strong tensile force to pull stems upward, while compression wood of gymnosperms creates compressive force to push stems upward. In this review, the general features and evolution of tension wood and compression wood are presented, along with descriptions of how gravitropisms and reaction woods contribute to the survival and morphology of trees. An overview is presented of the molecular and genetic mechanisms underlying graviperception, initial graviresponse and the regulation of tension wood development in the model angiosperm, Populus. Critical research questions and new approaches are discussed. No claim to US Government works New Phytologist © 2016 New Phytologist Trust.

  19. Techno-economic analysis of wood biomass boilers for the greenhouse industry

    International Nuclear Information System (INIS)

    Chau, J.; Sowlati, T.; Sokhansanj, S.; Preto, F.; Melin, S.; Bi, X.

    2009-01-01

    The objective of this study is to perform a techno-economic analysis on a typical wood pellet and wood residue boiler for generation of heat to an average-sized greenhouse in British Columbia. The variables analyzed included greenhouse size and structure, boiler efficiency, fuel types, and source of carbon dioxide (CO 2 ) for crop fertilization. The net present value (NPV) show that installing a wood pellet or a wood residue boiler to provide 40% of the annual heat demand is more economical than using a natural gas boiler to provide all the heat at a discount rate of 10%. For an assumed lifespan of 25 years, a wood pellet boiler system could generate NPV of C$259,311 without electrostatic precipitator (ESP) and C$74,695 with ESP, respectively. While, installing a wood residue boiler with or without an ESP could provide NPV of C$919,922 or C$1,104,538, respectively. Using a wood biomass boiler could also eliminate over 3000 tonne CO 2 equivalents of greenhouse gases annually. Wood biomass combustion generates more particulate matters than natural gas combustion. However, an advanced emission control system could significantly reduce particulate matters emission from wood biomass combustion which would bring the particulate emission to a relatively similar level as for natural gas

  20. On the role of CFRP reinforcement for wood beams stiffness

    Science.gov (United States)

    Ianasi, A. C.

    2015-11-01

    In recent years, carbon fiber composites have been increasingly used in different ways in reinforcing structural elements. Specifically, the use of composite materials as a reinforcement for wood beams under bending loads requires paying attention to several aspects of the problem such as the number of the composite layers applied on the wood beams. Study consolidation of composites revealed that they are made by bonding fibrous material impregnated with resin on the surface of various elements, to restore or increase the load carrying capacity (bending, cutting, compression or torque) without significant damage of their rigidity. Fibers used in building applications can be fiberglass, aramid or carbon. Items that can be strengthened are concrete, brick, wood, steel and stone, and in terms of structural beams, walls, columns and floors. This paper describes an experimental study which was designed to evaluate the effect of composite material on the stiffness of the wood beams. It proposes a summary of the fundamental principles of analysis of composite materials and the design and use. The type of reinforcement used on the beams is the carbon fiber reinforced polymer (CFRP) sheet and plates and also an epoxy resin for bonding all the elements. Structural epoxy resins remain the primary choice of adhesive to form the bond to fiber-reinforced plastics and are the generally accepted adhesives in bonded CFRP-wood connections. The advantages of using epoxy resin in comparison to common wood-laminating adhesives are their gap-filling qualities and the low clamping pressures that are required to form the bond between carbon fiber plates or sheets and the wood beams. Mechanical tests performed on the reinforced wood beams showed that CFRP materials may produce flexural displacement and lifting increases of the beams. Observations of the experimental load-displacement relationships showed that bending strength increased for wood beams reinforced with CFRP composite plates

  1. Robert Williams Wood: pioneer of invisible light.

    Science.gov (United States)

    Sharma, Shruti; Sharma, Amit

    2016-03-01

    The Wood's lamp aids in the diagnosis of multiple infectious, inflammatory and neoplastic dermatologic conditions. Although the Wood's lamp has many applications, which have improved both the diagnosis and management of disease, the man credited for its invention is relatively unknown in medicine. Robert Williams Wood, a prominent physicist of the early 20th century, is credited for the invention of the Wood's lamp. Wood was the father of infrared and ultraviolet photography and made significant contributions to other areas in optics and spectroscopy. Wood's work encompassed the formative years of American Physics; he published over 200 original papers over his lifetime. A few years after the invention of the Wood's lamp for ultraviolet photography, physicians in Europe adopted the Wood's lamp for dermatologic applications. Wood's lamp remains popular in clinics globally, given its ease of use and ability to improve diagnostic precision. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  2. Comparative ecobalancing accounting of semi-central house heat supply from wood residues; Vergleichende Oekobilanzierung der semi-zentralen Hauswaermebereitstellung aus Holzreststoffen

    Energy Technology Data Exchange (ETDEWEB)

    Biemann, Kirsten

    2015-07-01

    impact. Heat demanders and network structure vary for the different settlement types. This impacts the heat losses and the amount of energy generated from wood in the network. Combined heat and power plants promise higher fuel utilization. They decrease costs and environmental impacts. The heat losses in the network vary greatly between 23 percent for small single-family houses and 4 percent for big multi-family buildings. Therefore networks with bigger heat demanders have lower environmental burdens. From an economic point of view the conversion from a gas heater to the connection of a multi- family building to a semi- centralized heating network using wood residues as fuel is worthwhile. However for a single-family building this is often not the case. A comparison between the semi- centralized heat supply from wood residues and the commonly used heat supply from gas heaters shows a large potential to decrease greenhouse gas emissions, ozone depletion and fossil resource usage when using the first variant. However, it increases particulate matter formation, photochemical oxidant formation, eutrophication, and acidification. Only the usage of a wood gasification and a combined heat and power plant decreases particulate matter formation slightly. Similar results were obtained for a centralized heating network using wood residues as fuel. Using wood heaters in the buildings further decreases greenhouse gas emissions, ozone depletion and fossil resources, but results in an increased particulate matter formation. This particulate matter formation is over 1.000 percent bigger than for gas heaters.

  3. LA PLANTA ÚNICA COMO TIPO RESISTENTE A LA ESCALA / the single plan as a type resistant to scale

    Directory of Open Access Journals (Sweden)

    Silvia Colmenares Vilata

    2014-05-01

    Full Text Available RESUMEN El sistema capitalista ha generado dos de los modelos espaciales de indiferencia funcional más extremos: por un lado, el espacio tecnificado y repetido del edificio de oficinas en altura, encarnado por la ‘planta tipo’ y, por otro, el espacio diáfano y extenso del gran contendor, que responde a la lógica de lo que llamaremos ‘planta única’. En los edificios construidos para la industria automovilística y bélica americana se encuentra el germen de un tipo que servirá de modelo para los nuevos espacios de consumo de bienes y servicios de la ciudad post-industrial. En ella, la identificación del rascacielos con el centro y del contenedor con la periferia sigue vigente, porque la densidad necesaria del primero y la ocupación extensiva del segundo hacen que resulte imposible invertir los términos. Sin embargo, ambos representan el desarrollo estrictamente pragmático de los principios de la ‘planta libre’ como sistema operativo genérico, dando lugar a construcciones de gran tamaño que ponen a prueba la resistencia a la escala del propio tipo. Tomando como referencia la neutralidad característica de la ‘planta única’ el texto analiza el comportamiento frente al cambio de tamaño de sus dos configuraciones complementarias: la gran sala hipóstila y la gran sala diáfana. SUMMARY The capitalist system has generated two of the most extreme spatial models of functional indifference: on the one hand, the technified and repeated space of the high-rise office building, incarnated by the “typical plan” and, on the other, the diaphanous and extensive space of the large container, which responds to the logic of what we will call “single plan”. In the buildings constructed for the American automobile and military industries is the germ of a type that would serve as a model for the new spaces for consumption of goods and services of the post-industrial city. In that city, the identification of the skyscraper with the

  4. Reinforcement of Bolted Timber Joints Using GFRP Sheets in Poplar and Pine Woods

    Directory of Open Access Journals (Sweden)

    Mehrab Madhoushi

    2013-01-01

    Full Text Available Failure in timber structures occurs mainly in crucial points such as joints areas. Therefore, the idea of using composite sheets in timber joints has been intro-duced as a method in order to increase the strength and ductility behaviour of timber joints. This research aims to study the behaviour of bolted joints in poplar and pine woods, which are reinforced by two types of GFRP sheets. A single shear bolted joint consisted of 3 timber members whose length and width were 30 cm in length and 5 cm in width. The thickness of each member was 4 cm for internal part and 2 cm for external part. The employed steel bolt was 10 cm in length and 1 cm in diameter. In this respect, one layer of GFRP sheet was used to be bonded to timber members by using epoxy resin and left between the clamps for 24 hours. They were then kept at room temperature for three weeks. Also the effect of adding a wood veneer on the reinforced joints was investigated. The tensile strength of the reinforced and control samples (un-reinforced joints was measured according to ASTM D5652-92 standard. The results show that the reinforced samples have higher tensile strength compared to that of reinforced joints, although it is not statistically signifcant. Also, two types of sheets infuence the joint behaviour as the reinforced joints display more ductility behaviour.

  5. Single-crystalline M-type Sr Hexaferrites studied by {sup 57}Fe Mössbauer spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Nagasawa, Nobumoto, E-mail: rk15v002@stkt.u-hyogo.ac.jp; Ikeda, Shugo [University of Hyogo, Graduate School of Material Science and Center for Novel Material Science under Multi-extreme Conditions (Japan); Shimoda, Aiko; Waki, Takeshi; Tabata, Yoshikazu; Nakamura, Hiroyuki [Kyoto University, Department of Material Science and Engineering (Japan); Kobayashi, Hisao [University of Hyogo, Graduate School of Material Science and Center for Novel Material Science under Multi-extreme Conditions (Japan)

    2016-12-15

    The {sup 57}Fe Mössbauer spectra of the single crystalline and the finely ground Sr{sub 1−x}La{sub x}Fe{sub 12−y}Co{sub y}O{sub 19} (x = 0 : y = 0, x = 0.192 : y = 0.152 and x = 0.456 : y = 0.225) samples have been measured to investigate the La-Co substitution effects. All observed spectra at 150 K were well fitted using the five subspectra which correspond to the five crystallographical nonequivalent Fe sites in the M-type hexaferrite, indicating that the valence changes to Fe{sup 2+} ions in the Fe{sup 3+} ions were not observed in our Sr{sub 1−x}La{sub x}Fe{sub 12−y}Co{sub y}O{sub 19} samples. In SrFe{sub 12}O{sub 19}, the relative absorption intensities in the five subspectra show the large anisotropies in the recoilless fractions at the five Fe sites whereas these anisotropies were not observed in Sr{sub 0.544}La{sub 0.456}Fe{sub 11.775}Co{sub 0.225}O{sub 19}. These results indicate the chemical compositional dependence on the anisotropies of the recoilless fractions at the five Fe sites. The substitution of a Co{sup 2+} ion for the Fe{sup 3+} ion changes the center shifts of the Fe{sup 3+} ions near the Co{sup 2+} ion by the perturbation of the Fe-O-Co hybridizations. Therefore, the Co{sup 2+} ions occupy the 4f{sub 1} and the 4f{sub 2} sites due to the chemical compositional dependences of the refined magnetic hyperfine field and center shifts of the Fe{sup 3+} ions.

  6. Single base substitution causing the fragrant phenotype and development of a type-specific marker in aromatic coconut (Cocos nucifera).

    Science.gov (United States)

    Vongvanrungruang, A; Mongkolsiriwatana, C; Boonkaew, T; Sawatdichaikul, O; Srikulnath, K; Peyachoknagul, S

    2016-09-19

    The fragrance gene, betaine aldehyde dehydrogenase 2 (Badh2), has been well studied in many plant species. The objectives of this study were to clone Badh2 and compare the sequences between aromatic and non-aromatic coconuts. The complete coding region was cloned from cDNA of both aromatic and non-aromatic coconuts. The nucleotide sequences were highly homologous to Badh2 genes of other plants. Badh2 consisted of a 1512-bp open reading frame encoding 503 amino acids. A single nucleotide difference between aromatic and non-aromatic coconuts resulted in the conversion of alanine (non-aromatic) to proline (aromatic) at position 442, which was the substrate binding site of BADH2. The ring side chain of proline could destabilize the structure leading to a non-functional enzyme. Badh2 genomic DNA was cloned from exon 1 to 4, and from exon 5 to 15 from the two coconut types, except for intron 4 that was very long. The intron sequences of the two coconut groups were highly homologous. No differences in Badh2 expression were found among the tissues of aromatic coconut or between aromatic and non-aromatic coconuts. The amino acid sequences of BADH2 from coconut and other plants were compared and the genetic relationship was analyzed using MEGA 7.0. The phylogenetic tree reconstructed by the Bayesian information criterion consisted of two distinct groups of monocots and dicots. Among the monocots, coconut (Cocos nucifera) and oil palm (Elaeis guineensis) were the most closely related species. A marker for coconut differentiation was developed from one-base substitution site and could be successfully used.

  7. Dead wood in European beech (Fagus sylvatica) forest reserves

    NARCIS (Netherlands)

    Christensen, M.; Hahn, K.; Mountford, E.P.; Ódor, P.; Standovár, T.; Rozenbergar, D.; Diaci, J.; Wijdeven, S.M.J.; Meyer, P.; Winter, S.; Vrska, T.

    2005-01-01

    Data were analysed on the volume of dead wood in 86 beech forest reserves, covering most of the range of European beech forests. The mean volume was 130 m3/ha and the variation among reserves was high, ranging from almost nil to 550 m3/ha. The volume depended significantly on forest type, age since

  8. Emission of Dioxins from Danish Wood-Stoves

    DEFF Research Database (Denmark)

    Vikelsøe, J.; Madsen, Henrik; Hansen, K.

    1994-01-01

    The main purpose of the investigation was to estimate the annual dioxin emission from Danish wood-stoves. 4 stoves of different designs and 3 types of fuel were tested in 2 operating conditions. Sampling was carried out in a dilution tunnel, making reproducible sampling possible. The dioxin...

  9. Refraction and absorption of microwaves in wood

    International Nuclear Information System (INIS)

    Ziherl, Saša; Bajc, Jurij; Čepič, Mojca

    2013-01-01

    A demonstration experiment for physics students showing the dependence of the refractive index and absorption coefficient of wood on the direction of microwaves is presented. Wood and microwaves enable study of anisotropic properties, which are typically found in crystals. Wood is used as the persuasive representative of uniaxial anisotropic materials due to its visible structure and its consequent anisotropic properties. Wood can be cut in a general direction and wooden plates a few centimetres thick with well-defined fibre orientation are easily prepared. Microwaves are used because wood is transparent for microwaves and their centimetre-scale wavelength is comparable to the wood structure. (paper)

  10. DNA barcoding of vouchered xylarium wood specimens of nine endangered Dalbergia species.

    Science.gov (United States)

    Yu, Min; Jiao, Lichao; Guo, Juan; Wiedenhoeft, Alex C; He, Tuo; Jiang, Xiaomei; Yin, Yafang

    2017-12-01

    ITS2+ trnH - psbA was the best combination of DNA barcode to resolve the Dalbergia wood species studied. We demonstrate the feasibility of building a DNA barcode reference database using xylarium wood specimens. The increase in illegal logging and timber trade of CITES-listed tropical species necessitates the development of unambiguous identification methods at the species level. For these methods to be fully functional and deployable for law enforcement, they must work using wood or wood products. DNA barcoding of wood has been promoted as a promising tool for species identification; however, the main barrier to extensive application of DNA barcoding to wood is the lack of a comprehensive and reliable DNA reference library of barcodes from wood. In this study, xylarium wood specimens of nine Dalbergia species were selected from the Wood Collection of the Chinese Academy of Forestry and DNA was then extracted from them for further PCR amplification of eight potential DNA barcode sequences (ITS2, matK, trnL, trnH-psbA, trnV-trnM1, trnV-trnM2, trnC-petN, and trnS-trnG). The barcodes were tested singly and in combination for species-level discrimination ability by tree-based [neighbor-joining (NJ)] and distance-based (TaxonDNA) methods. We found that the discrimination ability of DNA barcodes in combination was higher than any single DNA marker among the Dalbergia species studied, with the best two-marker combination of ITS2+trnH-psbA analyzed with NJ trees performing the best (100% accuracy). These barcodes are relatively short regions (<350 bp) and amplification reactions were performed with high success (≥90%) using wood as the source material, a necessary factor to apply DNA barcoding to timber trade. The present results demonstrate the feasibility of using vouchered xylarium specimens to build DNA barcoding reference databases.

  11. Processing of the wood angelim pedra (Hymenolobium petraeum

    Directory of Open Access Journals (Sweden)

    Adjenane Corrêa Taques

    2016-08-01

    Full Text Available This study aimed to verify the behavior of wood Angelim stone (Hymenolobium petraeum Ducke submitted to the machining process. The study was developed in a carpentry shop in the city of Alta Floresta-MT. 36 boards with dimensions of 150 cm x 13.5 cm x 2.5 cm, length, width and thickness were randomly selected respectively for machining tests. The tests were developed according to the machinability of equipment used by the furniture industry, planing, sanding, drill and split by nail. 8 boards of wood in the stack were selected randomly to determine the moisture, according to 7190 (ABNT, 1997. The notes used for evaluation of defects resulting in the wood during the machining processes were assigned according to ASTM D 1666 (1987. It was observed that the type of angelim stone showed excellent performance in grinding tests, no scratch on the surface piece a of the burring parts and the parts free from defects, with the burning of wood. In cracking test for nail had a good performance, because it showed cracks with the insertion of the nail and planing test a regular performance, with pullout grain, surface arrepiamento and pullout chip. Wood Angelim stone responds with quality to the machining processes in planing, sanding, drill and split by nail.

  12. How the climate limits the wood density of angiosperms

    Science.gov (United States)

    Choi, Jin Woo; Kim, Ho-Young

    2017-11-01

    Flowering trees have various types of wood structure to perform multiple functions under their environmental conditions. In addition to transporting water from the roots to the canopy and providing mechanical support, the structure should provide resistance to embolism to maintain soil-plant-atmosphere continuum. By investigating existing data of the resistivity to embolism and wood density of 165 angiosperm species, here we show that the climate can limit the intrinsic properties of trees. Trees living in the dry environments require a high wood density to slow down the pressure decrease as it loses water relatively fast by evaporation. However, building too much tissues will result in the decrease of hydraulic conductivity and moisture concentration around mesophyll cells. To rationalize the biologically observed lower bound of the wood density, we construct a mechanical model to predict the wood density as a function of the vulnerability to embolism and the time for the recovery. Also, we build an artificial system using hydrogel microchannels that can test the probability of embolism as a function of conduit distributions. Our theoretical prediction is shown to be consistent with the results obtained from the artificial system and the biological data.

  13. Bioplastic production using wood mill effluents as feedstock.

    Science.gov (United States)

    Ben, M; Mato, T; Lopez, A; Vila, M; Kennes, C; Veiga, M C

    2011-01-01

    Fibreboard production is one of the most important industrial activities in Galicia (Spain). Great amounts of wastewater are generated, with properties depending on the type of wood, treatment process, final product and water reusing, among others. These effluents are characterized by a high chemical oxygen demand, low pH and nutrients limitation. Although anaerobic digestion is one of the most suitable processes for the treatment, lately bioplastics production (mainly polyhydroxyalkanoates) from wastewaters with mixed cultures is being evaluated. Substrate requirements for these processes consist of high organic matter content and low nutrient concentration. Therefore, wood mill effluents could be a suitable feedstock. In this work, the possibility of producing bioplastics from to wood mill effluents is evaluated. First, wood mill effluent was converted to volatile fatty acids in an acidogenic reactor operated at two different hydraulic retention times of 1 and 1.5 d. The acidification percentage obtained was 37% and 42%, respectively. Then, aerobic batch assays were performed using fermented wood mill effluents obtained at different hydraulic retention times. Assays were developed using different cultures as inoculums. The maximum storage yield of 0.57 Cmmol/Cmmol was obtained when when the culture was enriched on a synthetic media.

  14. Reaction to fire of ETICS applied on wood particle board

    Directory of Open Access Journals (Sweden)

    Bonati Antonio

    2016-01-01

    Full Text Available As well known the ETICS are diffusely used both for energy saving and thermal insulation reasons. They have been applied recently in wood buildings and in regions of southern Europe too due to green building and sustainability reasons. ITC-CNR has tested a lot of building materials and developed good knowledge about reaction to fire since the 1980 and currently, ETICS fixed directly to particle wood panels have been investigated with several SBI tests. In the case study are presented the main factors that can influence the fire reaction results when applied on wood structure are highlighted: the thickness of the insulating material, the presence of accidental damage, the flame attack from the inside. From the results obtained by tests on samples prepared with simulated accidental damages and fire from inside, some considerations are made about the hazard due to this specific construction technology and others on limits of the type of actually used standards product classification.

  15. Masked Visual Analysis: Minimizing Type I Error in Visually Guided Single-Case Design for Communication Disorders

    Science.gov (United States)

    Byun, Tara McAllister; Hitchcock, Elaine R.; Ferron, John

    2017-01-01

    Purpose: Single-case experimental designs are widely used to study interventions for communication disorders. Traditionally, single-case experiments follow a response-guided approach, where design decisions during the study are based on participants' observed patterns of behavior. However, this approach has been criticized for its high rate of…

  16. Effects of Calorie Restriction and Fiber Type on Glucose Uptake and Abundance of Electron Transport Chain and Oxidative Phosphorylation Proteins in Single Fibers from Old Rats.

    Science.gov (United States)

    Wang, Haiyan; Arias, Edward B; Yu, Carmen S; Verkerke, Anthony R P; Cartee, Gregory D

    2017-11-09

    Calorie restriction (CR; reducing calorie intake by ~40% below ad libitum) can increase glucose uptake by insulin-stimulated muscle. Because skeletal muscle is comprised of multiple, heterogeneous fiber types, our primary aim was to determine the effects of CR (initiated at 14 weeks old) and fiber type on insulin-stimulated glucose uptake by single fibers of diverse fiber types in 23-26-month-old rats. Isolated epitrochlearis muscles from AL and CR rats were incubated with [3H]-2-deoxyglucose ± insulin. Glucose uptake and fiber type were determined for single fibers dissected from the muscles. We also determined CR-effects on abundance of several key metabolic proteins in single fibers. CR resulted in: (a) significantly (p glucose uptake by insulin-stimulated type I, IIA, IIB, IIBX, and IIX fibers; (b) significantly (p glucose uptake in each fiber type of rat skeletal muscle in the absence of upregulation of the abundance of hexokinase II or key mitochondrial ETC and OxPhos proteins. © The Author 2017. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  17. Activities of chitinolytic enzymes during primary and secondary colonization of wood by basidiomycetous fungi.

    Science.gov (United States)

    Lindahl, Björn D; Finlay, Roger D

    2006-01-01

    The nitrogen (N) content of wood is usually suboptimal for fungal colonization. During decomposition of wood, an increasing fraction of the N becomes incorporated into fungal mycelium. Between 5 and 50% of the N in wood-degrading mycelium may be incorporated into chitin. Chitinolytic enzymes render this N available for re-utilization. Here, the activities of chitinolytic enzymes produced by wood-rotting fungi during degradation of spruce (Picea abies) wood were quantified in situ using fluorogenic 4-methylumbelliferyl substrates. A new method was developed that enables spatial quantification of enzyme activities on solid surfaces. All of the three tested fungi produced endochitinases, chitobiosidases and N-acetylhexosaminidases during colonization of wood. N-acetylhexosaminidase activity, and in some cases also chitobiosidase and endochitinase activities, were higher during secondary overgrowth of another fungus than during primary colonization of noncolonized wood. The results suggest that wood-degrading fungi degrade their own cell walls as well as the hyphae of earlier colonizers. Recycling of cell wall material within single mycelia and between fungal individuals during succession may lead to retention of N within woody debris.

  18. Hydrogeologic framework of the Wood River Valley aquifer system, south-central Idaho

    Science.gov (United States)

    Bartolino, James R.; Adkins, Candice B.

    2012-01-01

    metamorphosed to some degree, thus rock types and their relationships vary over distance. Quaternary-age sediment and basalt compose the primary source of groundwater in the Wood River Valley aquifer system. These Quaternary deposits can be divided into three units: a coarse-grained sand and gravel unit, a fine-grained silt and clay unit, and a single basalt unit. The fine- and coarse-grained units were primarily deposited as alluvium derived from glaciation in the surrounding mountains and upper reaches of tributary canyons. The basalt unit is found in the southeastern Bellevue fan area and is composed of two flows of different ages. Most of the groundwater produced from the Wood River Valley aquifer system is from the coarse-grained deposits. The altitude of the pre-Quaternary bedrock surface in the Wood River Valley was compiled from about 1,000 well-driller reports for boreholes drilled to bedrock and about 70 Horizontal-to-Vertical Spectral Ratio (HVSR) ambient-noise measurements. The bedrock surface generally mimics the land surface by decreasing down tributary canyons and the main valley from north to south; it ranges from more than 6,700 feet in Baker Creek to less than 4,600 feet in the central Bellevue fan. Most of the south-central portion of the Bellevue fan is underlain by an apparent topographically closed area on the bedrock surface that appears to drain to the southwest towards Stanton Crossing. Quaternary sediment thickness ranges from less than a foot on main and tributary valley margins to about 350 feet in the central Bellevue fan. Hydraulic conductivity for 81 wells in the study area was estimated from well-performance tests reported on well-driller reports. Estimated hydraulic conductivity for 79 wells completed in alluvium ranges from 1,900 feet per day (ft/d) along Warm Springs Creek to less than 1 ft/d in upper Croy Canyon. A well completed in bedrock had an estimated hydraulic conductivity value of 10 ft/d, one well completed in basalt had a value of

  19. Late Tertiary Petrified Wood from Nevada, USA: Evidence of Multiple Silicification Pathways

    Directory of Open Access Journals (Sweden)

    George E. Mustoe

    2015-10-01

    Full Text Available Late Tertiary fossil woods from the state of Nevada provide an opportunity for observing the mineralization sequences that cause buried wood to become permineralized. Oligocene and Miocene caldera basins contain abundant petrified wood that ranges in composition from incipient silicification to complete permineralization. Examination of specimens from 21 localities reveals that the petrifaction sequence can follow multiple pathways. Fossil wood specimens from a single stratum may have different mineralization; silicification may vary even within a single specimen. Despite these variations, several trends are evident. Features in Nevada specimens suggest that two fundamental processes are involved: early mineralization of cell walls, and later silica deposition in lumina, vessels, and rot pockets from groundwater that permeated these open spaces. The process of open-space filling may be analogous to the genesis of geodes and veins, where multiple episodes of hydrothermal precipitation may produce opal, chalcedony, and quartz as deposits within a single cavity. Silica polymorphs may coexist as primary precipitates, or they may originate from solid-state transformation of a single parent material. Relic lepisphere textures observed in some chalcedony wood specimens are evidence of opal→chalcedony transition. In Nevada, specimens that contain crystalline quartz, this mineral appears to have been formed by direct precipitation in open spaces, not from recrystallization of chalcedony. Opal-A has seldom been reported in fossil wood, but this amorphous material is fairly common in Nevada specimens.

  20. Harnessing light energy with a planar transparent hybrid of graphene/single wall carbon nanotube/n-type silicon heterojunction solar cell

    DEFF Research Database (Denmark)

    Chen, Leifeng; Yu, Hua; Zhong, Jiasong

    2015-01-01

    The photovoltaic conversion efficiency of a solar cell fabricated by a simple electrophoretic method with a planar transparent hybrid of graphenes (GPs) and single wall carbon nanotubes (SCNTs)/n-type silicon heterojunction was significantly increased compared to GPs/n-Si and SCNTs/n-Si solar cells...

  1. Erratum : Critical Properties of Spin-1 Antiferromagnetic Heisenberg Chains with Bond Alternation and Uniaxial Single-Ion-Type Anisotropy (vol 69, pg 237, 2000)

    OpenAIRE

    Chen, Wei; 飛田, 和男; Sanctuary, Bryan C.

    2008-01-01

    Original Paper :Critical Properties of Spin-1 Antiferromagnetic Heisenberg Chains with Bond Alternation and Uniaxial Single-Ion-Type AnisotropyWei Chen, Kazuo Hida and Bryan Clifford Sanctuary Journal of the Physical Society of Japan 69 (2000) pp.237-241

  2. MASH test 3-11 of the TxDOT single slope bridge rail (type SSTR) on pan-formed bridge deck

    Science.gov (United States)

    2011-03-01

    The objective of this crash test was to determine whether the TxDOT Single Slope Traffic Rail (Type : SSTR) would perform acceptably on a pan-formed deck when tested according to the guidelines set forth in : Manual for Assessing Safety Hardware (MAS...

  3. Molecular and functional identification of cyclic AMP-sensitive BKCa potassium channels (ZERO variant) and L-type voltage-dependent calcium channels in single rat juxtaglomerular cells

    DEFF Research Database (Denmark)

    Friis, Ulla G; Jørgensen, Finn; Andreasen, Ditte

    2003-01-01

    This study aimed at identifying the type and functional significance of potassium channels and voltage-dependent calcium channels (Ca(v)) in single rat JG cells using whole-cell patch clamp. Single JG cells displayed outward rectification at positive membrane potentials and limited net currents......, respectively. Double immunofluorescence confirmed the presence of BKCa and renin in the same cell. cAMP increased the outward current by 1.6-fold, and this was inhibited by 74% with iberiotoxin. Expression of the cAMP-sensitive splice variant (ZERO) of BKCa was confirmed in single-sampled JG cells by RT...... no effect. We conclude that JG cells express functional cAMP-sensitive BKCa channels (the ZERO splice variant) and voltage-dependent L-type Ca2+ channels....

  4. Wood pyrolysis oil for diesel engines

    Energy Technology Data Exchange (ETDEWEB)

    Paro, D.; Gros, S.; Hellen, G.; Jay, D.; Maekelae, T.; Rantanen, O.; Tanska, T. [Wartsila Diesel International Ltd Oy, Vaasa (Finland)

    1996-12-01

    Wood Pyrolysis oil (WPO) has been identified by the Technical Research Centre of Finland (VTT) as the most competitive biofuel product which can be produced from biomass. The fuel is produced by a fast pyrolysis technique, using wood chipping`s or sawdust. The process can be applied to other recycling products such as straw etc. The use of WPO as a Diesel power plant fuel has been studied, and a fuel specification has been developed. The fuel characteristics have been analysed. There are several fuel properties addressed in the paper which have had to be overcome. New materials have been used in the fuel injection system. The fuel injection system development has progressed from a pump-line-pipe system to a common rail system. The fuel requires a pilot fuel oil injection to initiate combustion. The targets for the fuel injection system have been 1500 bar and 30 deg C injection period with a fuel of 15 MJ/kg lower heating value and 1220 Kg/m{sup 3} density. The combustion characteristics from both a small 80 mm bore engine initially, and then later with a single cylinder test of a 320 mm bore Waertsilae engine, have been evaluated. (author)

  5. Wood: a construction material for tall buildings

    Science.gov (United States)

    Wimmers, Guido

    2017-12-01

    Wood has great potential as a building material, because it is strong and lightweight, environmentally friendly and can be used in prefabricated buildings. However, only changes in building codes will make wood competitive with steel and concrete.

  6. Ergonomics and safety in secondary wood processing

    Science.gov (United States)

    Rado Gazo; James D. McGlothlin; Yuehwern, Wiedenbeck, Jan Yih; Yuehwern Yih

    2002-01-01

    The main goal of the project was to initiate a pilot program in ergonomics for the secondary wood products industry. Case studies were conducted at three Midwest secondary wood product companies in 2000 and 2001.

  7. SYNERGISTIC WOOD PRESERVATIVES FOR REPLACEMENT OF CCA

    Science.gov (United States)

    The objective of this project was to evaluate the potential synergistic combinations of environmentally-safe biocides as wood preservatives. These wood preservatives could be potential replacements for the heavy-metal based CCA.Didecyldimethylammonium chloride [DDAC] was...

  8. Aerosol optical properties at Lampedusa (Central Mediterranean. 2. Determination of single scattering albedo at two wavelengths for different aerosol types

    Directory of Open Access Journals (Sweden)

    D. Meloni

    2006-01-01

    Full Text Available Aerosol optical properties were retrieved from direct and diffuse spectral irradiance measurements made by a multi-filter rotating shadowband radiometer (MFRSR at the island of Lampedusa (35.5° N, 12.6° E, in the Central Mediterranean, in the period July 2001–September 2003. In a companion paper (Pace et al., 2006 the aerosol optical depth (AOD and Ångström exponent were used together with airmass backward trajectories to identify and classify different aerosol types. The MFRSR diffuse-to-direct ratio (DDR at 415.6 nm and 868.7 nm for aerosol classified as 'biomass burning-urban/industrial', originating primarily from the European continent, and desert dust, originating from the Sahara, is used in this study to estimate the aerosol single scattering albedo (SSA. A detailed radiative transfer model is initialised with the measured aerosol optical depth; calculations are performed at the two wavelengths varying the SSA values until the modelled DDR matches the MFRSR observations. Sensitivity studies are performed to estimate how uncertainties on AOD, DDR, asymmetry factor (g, and surface albedo influence the retrieved SSA values. The results show that a 3% variation of AOD or DDR produce a change of about 0.02 in the retrieved SSA value at 415.6 and 868.7 nm; a ±0.06 variation of the asymmetry factor g produces a change of the estimated SSA of <0.04 at 415.6 nm, and <0.06 at 868.7 nm; finally, an increase of the assumed surface albedo of 0.05 causes very small changes (0.01–0.02 in the retrieved SSA. The calculations show that the SSA of desert dust (DD increases with wavelength, from 0.81±0.05 at 415.6 nm to 0.94±0.05 at 868.7 nm; on the contrary, the SSA of urban/industrial (UN aerosols decreases from 0.96±0.02 at 415.6 nm to 0.87±0.07 at 868.7 nm; the SSA of biomass burning (BB particles is 0.82±0.04 at 415.6 nm and 0.80±0.05 at 868.7 nm. Episodes of UN aerosols occur usually in June and July; long lasting BB aerosol episodes

  9. Wood preservatives and pressure-treated wood: considerations for historic-preservation projects

    Science.gov (United States)

    Ronald W. Anthony; Stan T. Lebow

    2015-01-01

    Wood, an abundant resource throughout most of the world, has been used as a building material for thousands of years. Many historic buildings have been built primarily of wood, and masonry and stone buildings generally have wood elements, both structural and architectural. As a biological material, wood is both remarkably complex and yet quite durable if well...

  10. Effects of wood fiber characteristics on mechanical properties of wood/polypropylene composites

    Science.gov (United States)

    Nicole M. Stark; Robert E. Rowlands

    2003-01-01

    Commercial wood flour, the most common wood-derived filler for thermoplastics, is produced in a mixture of particle sizes and generally has a lower aspect ratio than wood and other natural fibers. To understand how wood flour and fiber characteristics influence the mechanical properties of polypropylene composites, we first investigated the effect of different sizes of...

  11. Fuel wood symposium; Symposium Energieholz

    Energy Technology Data Exchange (ETDEWEB)

    Wild, C.; Wauer, A. (comps.)

    2001-07-01

    The Bavarian State Institute of Forestry (LWF) organised a 'Fuel Wood Symposium' in Freising-Weihenstephan on 17.11.2000. The purpose of this specialist conference was to give an overview of the use of biomass, especially wood, as an source of energy. (orig.) [German] Die Bayerische Landesanstalt fuer Wald und Forstwirtschaft richtete am 17.11.2000 in Freising-Weihenstephan das 'Symposium Energieholz' aus. Ziel der Fachtagung war es, einen Ueberblick ueber die energetische Nutzung von Biomasse, insbesondere Holz, zu geben. (orig.)

  12. Composite desiccant material "CaCl2/Vermiculite/Saw wood": a new material for fresh water production from atmospheric air

    Science.gov (United States)

    Kumar, Manoj; Yadav, Avadhesh

    2017-09-01

    In this study a novel composite desiccant material "CaCl2/Vermiculite/Saw wood" have been synthesized and tested for the water generation from atmospheric air. The vermiculite- saw wood used as a host matrix and CaCl2 as a hygroscopic salt. A solar glass desiccant box type system with a collector area of 0.36 m2 has been used. Design parameters for water generation are height of glass from the desiccant material bed as 0.22 m, inclination in angle as 30º, the effective thickness of glass as 3 mm and number of glazing as single. It has been found that the concentration of calcium chloride is the most influencing factor for fresh water generation from atmospheric air. The maximum amount of water produced by using novel composite desiccant material is 195 ml/kg/day.

  13. Wood Properties and Kinds; A Base Syllabus on Wood Technology.

    Science.gov (United States)

    Eastern Kentucky Univ., Richmond.

    Prepared by participants in the 1968 National Defense Education Act Institute on Wood Technology, this syllabus is one of a series of basic outlines designed to aid college level industrial arts instructors in improving and broadening the scope and content of their programs. This booklet is concerned largely with the physical composition and…

  14. Effect of adding biochar with wood vinegar on the growth of cucumber

    Science.gov (United States)

    Pan, Xin; Zhang, Yipeng; Wang, Xiao; Liu, Guocheng

    2017-04-01

    The chemical fertilizers are abused to improve crop yields, which cause lots of soil problems (e.g., soil compaction and native nutrient loss). We thus investigated the potential of the combination of biochar and wood vinegar as a new type of fertilizer to replace the traditional fertilizer. The results in this study showed that the combined addition of biochar with wood vinegar had the greatest promotion effect on the plant growth of cucumber. Compared to the control treatment, the biochar addition with wood vinegar significantly increased the plant height, root length, root volume and root tips by 29.7%, 117%, 121% and 76.1%, respectively. These positive effects could be attributed to the benefits of the addition of biochar with wood vinegar treatment on improving soil fertility, increasing nutrient supply, and further stimulating plant growth. Overall, the combination of biochar and wood vinegar could be a promising fertilizer to promote plants growth and enhance crop yields.

  15. Bioremediation of treated wood with fungi

    Science.gov (United States)

    Barbara L. Illman; Vina W. Yang

    2006-01-01

    The authors have developed technologies for fungal bioremediation of waste wood treated with oilborne or metal-based preservatives. The technologies are based on specially formulated inoculum of wood-decay fungi, obtained through strain selection to obtain preservative-tolerant fungi. This waste management approach provides a product with reduced wood volume and the...

  16. Effects of phosphoramides on wood dimensional stability

    Science.gov (United States)

    Hong-Lin. Lee; George C. Chen; Roger M. Rowell

    2000-01-01

    To evaluate the dimensional stability of phosphoramide-reacted wood, wood was reacted with a mixture which was derived from compounding phosphorus pentoxide and each of 12 amines including alkyl, halophenyl, and phenyl amines in N,N-dimethylformamide. Dimensional stability of such reacted wood was analyzed by antishrink efficiency (ASE) using the water-soak method....

  17. Mapping wood production in European forests

    NARCIS (Netherlands)

    Verkerk, P.J.; Levers, C.; Kuemmerle, T.; Lindner, M.; Vanbuena, R.; Verburg, P.H.; Zudin, S.

    2015-01-01

    Wood production is an important forest use, impacting a range of other ecosystem services. However, information on the spatial patterns in wood production is limited and often available only for larger administrative units. In this study, we developed high-resolution wood production maps for

  18. Wood properties affecting finish service life

    Science.gov (United States)

    R. Sam. Williams; Charles. Jourdain; George I. Daisey; Robert W. Springate

    2000-01-01

    Wood is a biological material that has widely different properties depending on species, geographic area where the tree grew, the growth conditions, size of the tree at harvest, sawing, and other manufacturing processes. Some of the more important wood properties as they relate to wood finishing are discussed, e.g., growth rate, density, knots, extractives, juvenile...

  19. Build Green: Wood Can Last for Centuries

    Science.gov (United States)

    Carol A. Clausen; Samuel V. Glass

    2012-01-01

    This report updates and revises information from the 1976 Forest Service publication by Rodney C. DeGroot, “Your Wood Can Last for Centuries.” It explains why wood decays, alerts the homeowner to conditions that can result in decay in buildings, and describes measures to prevent moisture-related damage to wood.

  20. Characteristics and availability of commercially important woods

    Science.gov (United States)

    Regis B. Miller

    1999-01-01

    Throughout history, the unique characteristics and comparative abundance of wood have made it a natural material for homes and other structures, furniture, tools, vehicles, and decorative objects. Today, for the same reasons, wood is prized for a multitude of uses. All wood is composed of cellulose, lignin, hemicelluloses, and minor amounts (5% to 10%) of extraneous...