SURFACE INDUSTRIAL HVAC SYSTEM DESCRIPTION DOCUMENT

Energy Technology Data Exchange (ETDEWEB)

M.M. Ansari

2005-04-05

The purpose of this system description document (SDD) is to establish requirements that drive the design of the surface industrial heating, ventilation, and air-conditioning (HVAC) system and its bases to allow the design effort to proceed to license application. This SDD will be revised at strategic points as the design matures. This SDD identifies the requirements and describes the system design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This SDD is an engineering tool for design control; accordingly, the primary audience and users are design engineers. This SDD is part of an iterative design process. It leads the design process with regard to the flowdown of upper tier requirements onto the system. Knowledge of these requirements is essential to performing the design process. The SDD follows the design with regard to the description of the system. The description that provided in this SDD reflects the current results of the design process.

SNF/HLW Transfer System Description Document

International Nuclear Information System (INIS)

W. Holt

2005-01-01

The purpose of this system description document (SDD) is to establish requirements that drive the design of the spent nuclear fuel (SNF)/high-level radioactive waste (HLW) transfer system and associated bases, which will allow the design effort to proceed to license application. This SDD will be revised at strategic points as the design matures. This SDD identifies the requirements and describes the system design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This SDD is an engineering tool for design control. Accordingly, the primary audience and users are design engineers. This SDD is part of an iterative design process. It leads the design process with regard to the flowdown of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD follows the design with regard to the description of the system. The description provided in this SDD reflects the current results of the design process

Waste Management Systems Requirements and Descriptions (SRD)

International Nuclear Information System (INIS)

Conner, C.W.

1986-01-01

The Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM) is responsible for the development of a system for the management of high-level radioactive waste and spent fuel in accordance with the Nuclear Waste Policy Act of 1982. The Waste Management system requirements and description document is the program-level technical baseline document. The requirements include the functions that must be performed in order to achieve the system mission and performance criteria for those functions. This document covers only the functional requirements of the system; it does not cover programmatic or procedural requirements pertaining to the processes of designing, siting and licensing. The requirements are largely based on the Nuclear Waste Policy Act of 1982, Environmental Protection Agency standards, Nuclear Regulatory Commission regulations, and DOE orders and guidance. However, nothing in this document should be construed as to relieve the DOE or its contractors from their responsibilities to comply with applicable statutes, regulations, and standards. This document also provides a brief description of the system being developed to meet the requirements. In addition to the described ''authorized system,'' a system description is provided for an ''improved-performance system'' which would include a monitored retrievable storage (MRS) facility. In the event that an MRS facility is approved by Congress, the improved-performance system will become the reference system. Neither system description includes Federal Interim Storage (FIS) capabilities. Should the need for FIS be identified, it will be included as an additional system element. The descriptions are focused on the interfaces between the system elements, rather than on the detail of the system elements themselves

Waste receiving and processing plant control system; system design description

Energy Technology Data Exchange (ETDEWEB)

LANE, M.P.

1999-02-24

The Plant Control System (PCS) is a heterogeneous computer system composed of numerous sub-systems. The PCS represents every major computer system that is used to support operation of the Waste Receiving and Processing (WRAP) facility. This document, the System Design Description (PCS SDD), includes several chapters and appendices. Each chapter is devoted to a separate PCS sub-system. Typically, each chapter includes an overview description of the system, a list of associated documents related to operation of that system, and a detailed description of relevant system features. Each appendice provides configuration information for selected PCS sub-systems. The appendices are designed as separate sections to assist in maintaining this document due to frequent changes in system configurations. This document is intended to serve as the primary reference for configuration of PCS computer systems. The use of this document is further described in the WRAP System Configuration Management Plan, WMH-350, Section 4.1.

Waste receiving and processing plant control system; system design description

International Nuclear Information System (INIS)

LANE, M.P.

1999-01-01

The Plant Control System (PCS) is a heterogeneous computer system composed of numerous sub-systems. The PCS represents every major computer system that is used to support operation of the Waste Receiving and Processing (WRAP) facility. This document, the System Design Description (PCS SDD), includes several chapters and appendices. Each chapter is devoted to a separate PCS sub-system. Typically, each chapter includes an overview description of the system, a list of associated documents related to operation of that system, and a detailed description of relevant system features. Each appendice provides configuration information for selected PCS sub-systems. The appendices are designed as separate sections to assist in maintaining this document due to frequent changes in system configurations. This document is intended to serve as the primary reference for configuration of PCS computer systems. The use of this document is further described in the WRAP System Configuration Management Plan, WMH-350, Section 4.1

Unique Description for Single Transverse Spin Asymmetries in DIS and Hadronic Collisions

International Nuclear Information System (INIS)

Yuan Feng

2007-01-01

We derive a unique formula for the single-transverse-spin asymmetry in semi-inclusive hadron production in deep inelastic scattering, valid for all transverse momentum region. Based on this, we further study the integrated asymmetry weighted with transverse-momentum. They can be evaluated in terms of the twist-three quark-gluon correlation functions, which are responsible for the single spin asymmetry in single inclusive hadron production in hadronic collisions. By using the fitted twist-three functions from the hadronic collision data, we find a consistent description for SSAs in deep inelastic scattering. This demonstrates that we have a unique picture for SSAs in these two processes, and shall provide important guidelines for future studies

ELECTRICAL SUPPORT SYSTEM DESCRIPTION DOCUMENT

International Nuclear Information System (INIS)

Roy, S.

2004-01-01

The purpose of this revision of the System Design Description (SDD) is to establish requirements that drive the design of the electrical support system and their bases to allow the design effort to proceed to License Application. This SDD is a living document that will be revised at strategic points as the design matures over time. This SDD identifies the requirements and describes the system design as they exist at this time, with emphasis on those attributes of the design provided to meet the requirements. This SDD has been developed to be an engineering tool for design control. Accordingly, the primary audience/users are design engineers. This type of SDD both ''leads'' and ''trails'' the design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD trails the design with regard to the description of the system. The description provided in the SDD is a reflection of the results of the design process to date. Functional and operational requirements applicable to electrical support systems are obtained from the ''Project Functional and Operational Requirements'' (F andOR) (Siddoway 2003). Other requirements to support the design process have been taken from higher-level requirements documents such as the ''Project Design Criteria Document'' (PDC) (Doraswamy 2004), and fire hazards analyses. The above-mentioned low-level documents address ''Project Requirements Document'' (PRD) (Canon and Leitner 2003) requirements. This SDD contains several appendices that include supporting information. Appendix B lists key system charts, diagrams, drawings, and lists, and Appendix C includes a list of system procedures

Breeding description for fast reactors and symbiotic reactor systems

International Nuclear Information System (INIS)

Hanan, N.A.

1979-01-01

A mathematical model was developed to provide a breeding description for fast reactors and symbiotic reactor systems by means of figures of merit type quantities. The model was used to investigate the effect of several parameters and different fuel usage strategies on the figures of merit which provide the breeding description. The integrated fuel cycle model for a single-reactor is reviewed. The excess discharge is automatically used to fuel identical reactors. The resulting model describes the accumulation of fuel in a system of identical reactors. Finite burnup and out-of-pile delays and losses are treated in the model. The model is then extended from fast breeder park to symbiotic reactor systems. The asymptotic behavior of the fuel accumulation is analyzed. The asymptotic growth rate appears as the largest eigenvalue in the solution of the characteristic equations of the time dependent differential balance equations for the system. The eigenvector corresponding to the growth rate is the core equilibrium composition. The analogy of the long-term fuel cycle equations, in the framework of this model, and the neutron balance equations is explored. An eigenvalue problem adjoint to the one generated by the characteristic equations of the system is defined. The eigenvector corresponding to the largest eigenvalue, i.e. to the growth rate, represents the ''isotopic breeding worths.'' Analogously to the neutron adjoint flux it is shown that the isotopic breeding worths represent the importance of an isotope for breeding, i.e. for the growth rate of a system

System Design Description for the TMAD Code

International Nuclear Information System (INIS)

Finfrock, S.H.

1995-01-01

This document serves as the System Design Description (SDD) for the TMAD Code System, which includes the TMAD code and the LIBMAKR code. The SDD provides a detailed description of the theory behind the code, and the implementation of that theory. It is essential for anyone who is attempting to review or modify the code or who otherwise needs to understand the internal workings of the code. In addition, this document includes, in Appendix A, the System Requirements Specification for the TMAD System

Conceptual modular description of the high-level waste management system for system studies model development

International Nuclear Information System (INIS)

McKee, R.W.; Young, J.R.; Konzek, G.J.

1992-08-01

This document presents modular descriptions of possible alternative components of the federal high-level radioactive waste management system and the procedures for combining these modules to obtain descriptions for alternative configurations of that system. The 20 separate system component modules presented here can be combined to obtain a description of any of the 17 alternative system configurations (i.e., scenarios) that were evaluated in the MRS Systems Studies program (DOE 1989a). First-approximation descriptions of other yet-undefined system configurations could also be developed for system study purposes from this database. The descriptions include, in a modular format, both functional descriptions of the processes in the waste management system, plus physical descriptions of the equipment and facilities necessary for performance of those functions

Precision Attitude Determination System (PADS) system design and analysis: Single-axis gimbal star tracker

Science.gov (United States)

1974-01-01

The feasibility is evaluated of an evolutionary development for use of a single-axis gimbal star tracker from prior two-axis gimbal star tracker based system applications. Detailed evaluation of the star tracker gimbal encoder is considered. A brief system description is given including the aspects of tracker evolution and encoder evaluation. System analysis includes evaluation of star availability and mounting constraints for the geosynchronous orbit application, and a covariance simulation analysis to evaluate performance potential. Star availability and covariance analysis digital computer programs are included.

1993 baseline solid waste management system description

International Nuclear Information System (INIS)

Armacost, L.L.; Fowler, R.A.; Konynenbelt, H.S.

1994-02-01

Pacific Northwest Laboratory has prepared this report under the direction of Westinghouse Hanford Company. The report provides an integrated description of the system planned for managing Hanford's solid low-level waste, low-level mixed waste, transuranic waste, and transuranic mixed waste. The primary purpose of this document is to illustrate a collective view of the key functions planned at the Hanford Site to handle existing waste inventories, as well as solid wastes that will be generated in the future. By viewing this system as a whole rather than as individual projects, key facility interactions and requirements are identified and a better understanding of the overall system may be gained. The system is described so as to form a basis for modeling the system at various levels of detail. Model results provide insight into issues such as facility capacity requirements, alternative system operating strategies, and impacts of system changes (ie., startup dates). This description of the planned Hanford solid waste processing system: defines a baseline system configuration; identifies the entering waste streams to be managed within the system; identifies basic system functions and waste flows; and highlights system constraints. This system description will evolve and be revised as issues are resolved, planning decisions are made, additional data are collected, and assumptions are tested and changed. Out of necessity, this document will also be revised and updated so that a documented system description, which reflects current system planning, is always available for use by engineers and managers. It does not provide any results generated from the many alternatives that will be modeled in the course of analyzing solid waste disposal options; such results will be provided in separate documents

ELECTRICAL POWER SYSTEM DESCRIPTION DOCUMENT

Energy Technology Data Exchange (ETDEWEB)

M. Maniyar

2004-06-22

The purpose of this revision of the System Description Document (SDD) is to establish requirements that drive the design of the electrical power system and their bases to allow the design effort to proceed to License Application. This SDD is a living document that will be revised at strategic points as the design matures over time. This SDD identifies the requirements and describes the system design as they exist at this time, with emphasis on those attributes of the design provided to meet the requirements. This SDD has been developed to be an engineering tool for design control. Accordingly, the primary audience are design engineers. This type of SDD leads and follows the design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential to performing the design process. This SDD follows the design with regard to the description of the system. The description provided in the SDD is a reflection of the results of the design process to date. Functional and operational requirements applicable to this system are obtained from ''Project Functional and Operational Requirements'' (F&OR) (Siddoway, 2003). Other requirements to support the design process have been taken from higher level requirements documents such as ''Project Design Criteria Document'' (PDC) (Doraswamy 2004), the fire hazards analyses, and the preclosure safety analysis. The above mentioned low-level documents address ''Project Requirements Document'' (PRD) (Canori and Leitner 2003) requirements. This SDD includes several appendices with supporting information. Appendix B lists key system charts, diagrams, drawings, and lists; and Appendix C is a list of system procedures.

ELECTRICAL SUPPORT SYSTEM DESCRIPTION DOCUMENT

Energy Technology Data Exchange (ETDEWEB)

S. Roy

2004-06-24

The purpose of this revision of the System Design Description (SDD) is to establish requirements that drive the design of the electrical support system and their bases to allow the design effort to proceed to License Application. This SDD is a living document that will be revised at strategic points as the design matures over time. This SDD identifies the requirements and describes the system design as they exist at this time, with emphasis on those attributes of the design provided to meet the requirements. This SDD has been developed to be an engineering tool for design control. Accordingly, the primary audience/users are design engineers. This type of SDD both ''leads'' and ''trails'' the design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD trails the design with regard to the description of the system. The description provided in the SDD is a reflection of the results of the design process to date. Functional and operational requirements applicable to electrical support systems are obtained from the ''Project Functional and Operational Requirements'' (F&OR) (Siddoway 2003). Other requirements to support the design process have been taken from higher-level requirements documents such as the ''Project Design Criteria Document'' (PDC) (Doraswamy 2004), and fire hazards analyses. The above-mentioned low-level documents address ''Project Requirements Document'' (PRD) (Canon and Leitner 2003) requirements. This SDD contains several appendices that include supporting information. Appendix B lists key system charts, diagrams, drawings, and lists, and Appendix C includes a list of system procedures.

Unbinding Transition of Probes in Single-File Systems

Science.gov (United States)

Bénichou, Olivier; Démery, Vincent; Poncet, Alexis

2018-02-01

Single-file transport, arising in quasi-one-dimensional geometries where particles cannot pass each other, is characterized by the anomalous dynamics of a probe, notably its response to an external force. In these systems, the motion of several probes submitted to different external forces, although relevant to mixtures of charged and neutral or active and passive objects, remains unexplored. Here, we determine how several probes respond to external forces. We rely on a hydrodynamic description of the symmetric exclusion process to obtain exact analytical results at long times. We show that the probes can either move as a whole, or separate into two groups moving away from each other. In between the two regimes, they separate with a different dynamical exponent, as t1 /4. This unbinding transition also occurs in several continuous single-file systems and is expected to be observable.

Description of surface systems. Preliminary site description. Forsmark area Version 1.2

Energy Technology Data Exchange (ETDEWEB)

Lindborg, Tobias [ed.

2005-06-01

Swedish Nuclear Fuel and Waste Management Co (SKB) started site investigations for a deep repository for spent nuclear fuel in 2002 at two different sites in Sweden, Forsmark and Oskarshamn. The investigations should provide necessary information for a license application aimed at starting underground exploration. For this reason, ecosystem data need to be interpreted and assessed into site descriptive models, which in turn are used for safety assessment studies and for environmental impact assessment. Descriptions of the surface system are also needed for further planning of the site investigations. This report describes the surface ecosystems of the Forsmark site (e.g. hydrology, Quaternary deposits, chemistry, vegetation, animals and the human land use). The ecosystem description is an integration of the site and its regional setting, covering the current state of the biosphere as well as the ongoing natural processes affecting the longterm development. Improving the descriptions is important during both the initial and the complete site investigation phase. Before starting of the initial phase in Forsmark, version 0 of the site descriptive model was developed. The results of the initial site investigation phase is compiled into a preliminary site description of Forsmark (version 1.2) in June 2005. This report provides the major input and background to the biosphere description, in the 1.2 version of the Forsmark site description. The basis for this interim version is quality-assured field data from the Forsmark sub area and regional area, available in the SKB SICADA, and GIS data bases as of July 31th 2004 as well as version 1.1 of the Site Descriptive Model. To achieve an ecosystem site description there is a need to develop discipline-specific models by interpreting and analysing primary data. The different discipline-specific models are then integrated into a system describing interactions and flows and stocks of matter between and within functional units in

Description of surface systems. Preliminary site description. Forsmark area Version 1.2

International Nuclear Information System (INIS)

Lindborg, Tobias

2005-06-01

Swedish Nuclear Fuel and Waste Management Co (SKB) started site investigations for a deep repository for spent nuclear fuel in 2002 at two different sites in Sweden, Forsmark and Oskarshamn. The investigations should provide necessary information for a license application aimed at starting underground exploration. For this reason, ecosystem data need to be interpreted and assessed into site descriptive models, which in turn are used for safety assessment studies and for environmental impact assessment. Descriptions of the surface system are also needed for further planning of the site investigations. This report describes the surface ecosystems of the Forsmark site (e.g. hydrology, Quaternary deposits, chemistry, vegetation, animals and the human land use). The ecosystem description is an integration of the site and its regional setting, covering the current state of the biosphere as well as the ongoing natural processes affecting the longterm development. Improving the descriptions is important during both the initial and the complete site investigation phase. Before starting of the initial phase in Forsmark, version 0 of the site descriptive model was developed. The results of the initial site investigation phase is compiled into a preliminary site description of Forsmark (version 1.2) in June 2005. This report provides the major input and background to the biosphere description, in the 1.2 version of the Forsmark site description. The basis for this interim version is quality-assured field data from the Forsmark sub area and regional area, available in the SKB SICADA, and GIS data bases as of July 31th 2004 as well as version 1.1 of the Site Descriptive Model. To achieve an ecosystem site description there is a need to develop discipline-specific models by interpreting and analysing primary data. The different discipline-specific models are then integrated into a system describing interactions and flows and stocks of matter between and within functional units in

Impact of Single-Case Pupil Descriptions on Student Teacher Attitudes towards Inclusive Education

Science.gov (United States)

Röhm, Alexander; Schnöring, Annika; Hastall, Matthias R.

2018-01-01

Institutional and individual stigmatization are still major barriers for children with disabilities to access education. Teacher attitudes towards inclusive education play a crucial role in this regard, and are shaped by single-case descriptions from mass media or other sources. Building on exemplification theory and priming, two experiments with…

Automatic TLI recognition system. Part 1: System description

Energy Technology Data Exchange (ETDEWEB)

Partin, J.K.; Lassahn, G.D.; Davidson, J.R.

1994-05-01

This report describes an automatic target recognition system for fast screening of large amounts of multi-sensor image data, based on low-cost parallel processors. This system uses image data fusion and gives uncertainty estimates. It is relatively low cost, compact, and transportable. The software is easily enhanced to expand the system`s capabilities, and the hardware is easily expandable to increase the system`s speed. This volume gives a general description of the ATR system.

SNF AGING SYSTEM DESCRIPTION DOCUMENT

Energy Technology Data Exchange (ETDEWEB)

L.L. Swanson

2005-04-06

The purpose of this system description document (SDD) is to establish requirements that drive the design of the spent nuclear fuel (SNF) aging system and associated bases, which will allow the design effort to proceed. This SDD will be revised at strategic points as the design matures. This SDD identifies the requirements and describes the system design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This SDD is an engineering tool for design control; accordingly, the primary audience and users are design engineers. This SDD is part of an iterative design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD follows the design with regard to the description of the system. The description provided in the SDD reflects the current results of the design process. Throughout this SDD, the term aging cask applies to vertical site-specific casks and to horizontal aging modules. The term overpack is a vertical site-specific cask that contains a dual-purpose canister (DPC) or a disposable canister. Functional and operational requirements applicable to this system were obtained from ''Project Functional and Operational Requirements'' (F&OR) (Curry 2004 [DIRS 170557]). Other requirements that support the design process were taken from documents such as ''Project Design Criteria Document'' (PDC) (BSC 2004 [DES 171599]), ''Site Fire Hazards Analyses'' (BSC 2005 [DIRS 172174]), and ''Nuclear Safety Design Bases for License Application'' (BSC 2005 [DIRS 171512]). The documents address requirements in the ''Project Requirements Document'' (PRD) (Canori and Leitner 2003 [DIRS 166275]). This SDD includes several appendices. Appendix A is a Glossary; Appendix B is a list of key system charts

SNF AGING SYSTEM DESCRIPTION DOCUMENT

International Nuclear Information System (INIS)

L.L. Swanson

2005-01-01

The purpose of this system description document (SDD) is to establish requirements that drive the design of the spent nuclear fuel (SNF) aging system and associated bases, which will allow the design effort to proceed. This SDD will be revised at strategic points as the design matures. This SDD identifies the requirements and describes the system design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This SDD is an engineering tool for design control; accordingly, the primary audience and users are design engineers. This SDD is part of an iterative design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD follows the design with regard to the description of the system. The description provided in the SDD reflects the current results of the design process. Throughout this SDD, the term aging cask applies to vertical site-specific casks and to horizontal aging modules. The term overpack is a vertical site-specific cask that contains a dual-purpose canister (DPC) or a disposable canister. Functional and operational requirements applicable to this system were obtained from ''Project Functional and Operational Requirements'' (F andOR) (Curry 2004 [DIRS 170557]). Other requirements that support the design process were taken from documents such as ''Project Design Criteria Document'' (PDC) (BSC 2004 [DES 171599]), ''Site Fire Hazards Analyses'' (BSC 2005 [DIRS 172174]), and ''Nuclear Safety Design Bases for License Application'' (BSC 2005 [DIRS 171512]). The documents address requirements in the ''Project Requirements Document'' (PRD) (Canori and Leitner 2003 [DIRS 166275]). This SDD includes several appendices. Appendix A is a Glossary; Appendix B is a list of key system charts, diagrams, drawings, lists and additional supporting information; and Appendix C is a list of

On the description of fault-tolerant systems

International Nuclear Information System (INIS)

Syrbe, M.

1980-01-01

Various demands by increasing complexity and the disposability of new technologies, like the One-chip-microcomputer and fiber optics, lead to control systems, which are built as decentralized distributed multi-microcomputersystems. They realize not only new control functions but they also open possibilities to increase availability by fault-tolerance. The design or the selection and lay-out of such systems require a quantitative description of these systems. This is possible on the bases of the set of hardware and software moduls of the system by the use of queuing models, reliability nets and diagnostic graphs. This is shown by an example of a practically applied Really Distributed Computer Control System (RDC-System). Computer aided methods for these system descriptions are emphasized. (orig.) [de

System description of the Repository-Only System for the FY 1990 systems integration program studies

International Nuclear Information System (INIS)

McKee, R.W.; Young, J.R.; Konzek, G.J.

1991-07-01

This document provides both functional and physical descriptions of a conceptual high-level waste management system defined as a Repository-Only System. Its purpose is to provide a basis for required system computer modeling and system studies initiated in FY 1990 under the Systems Integration Program of the US Department of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM). The Repository-Only System is designed to accept 3000 MTU per year of spent fuel and 400 equivalent MTU per year of high-level wastes disposal in the geologic repository. This document contains both functional descriptions of the processes in the waste management system and physical descriptions of the equipment and facilities necessary for performance of those processes. These descriptions contain the level of detail needed for the projected systems analysis studies. The Repository-Only System contains all system components, from the waste storage facilities of the waste generators to the underground facilities for final disposal of the wastes. The major facilities in the system are the waste generator waste storage facilities, a repository facility that packages the wastes and than emplaces them in the geologic repository, and the transportation equipment and facilities for transporting the wastes between these major facilities. 18 refs., 39 figs

Advanced Transport Operating System (ATOPS) color displays software description microprocessor system

Science.gov (United States)

Slominski, Christopher J.; Plyler, Valerie E.; Dickson, Richard W.

1992-01-01

This document describes the software created for the Sperry Microprocessor Color Display System used for the Advanced Transport Operating Systems (ATOPS) project on the Transport Systems Research Vehicle (TSRV). The software delivery known as the 'baseline display system', is the one described in this document. Throughout this publication, module descriptions are presented in a standardized format which contains module purpose, calling sequence, detailed description, and global references. The global reference section includes procedures and common variables referenced by a particular module. The system described supports the Research Flight Deck (RFD) of the TSRV. The RFD contains eight cathode ray tubes (CRTs) which depict a Primary Flight Display, Navigation Display, System Warning Display, Takeoff Performance Monitoring System Display, and Engine Display.

Epsilon. A System Description Language

DEFF Research Database (Denmark)

Jensen, Kurt; Kyng, Morten

This paper discusses the use of Petri nets as a semantic tool in the design of languages and in the construction and analysis of system descriptions. The topics treated are: -- Languages based on nets. -- The problem of time in nets. -- Nets and related models. -- Nets and formal semantics...

Irreducible descriptive sets of attributes for information systems

KAUST Repository

Moshkov, Mikhail

2010-01-01

The maximal consistent extension Ext(S) of a given information system S consists of all objects corresponding to attribute values from S which are consistent with all true and realizable rules extracted from the original information system S. An irreducible descriptive set for the considered information system S is a minimal (relative to the inclusion) set B of attributes which defines exactly the set Ext(S) by means of true and realizable rules constructed over attributes from the considered set B. We show that there exists only one irreducible descriptive set of attributes. We present a polynomial algorithm for this set construction. We also study relationships between the cardinality of irreducible descriptive set of attributes and the number of attributes in S. The obtained results will be useful for the design of concurrent data models from experimental data. © 2010 Springer-Verlag.

Hot Spot Removal System: System description

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

Hazardous wastes contaminated with radionuclides, chemicals, and explosives exist across the Department of Energy complex and need to be remediated due to environmental concerns. Currently, an opportunity is being developed to dramatically reduce remediation costs and to assist in the acceleration of schedules associated with these wastes by deploying a Hot Spot Removal System. Removing the hot spot from the waste site will remove risk driver(s) and enable another, more cost effective process/option/remedial alternative (i.e., capping) to be applied to the remainder of the site. The Hot Spot Removal System consists of a suite of technologies that will be utilized to locate and remove source terms. Components of the system can also be used in a variety of other cleanup activities. This Hot Spot Removal System Description document presents technologies that were considered for possible inclusion in the Hot Spot Removal System, technologies made available to the Hot Spot Removal System, industrial interest in the Hot Spot Removal System`s subsystems, the schedule required for the Hot Spot Removal System, the evaluation of the relevant technologies, and the recommendations for equipment and technologies as stated in the Plan section.

Hot Spot Removal System: System description

International Nuclear Information System (INIS)

1997-09-01

Hazardous wastes contaminated with radionuclides, chemicals, and explosives exist across the Department of Energy complex and need to be remediated due to environmental concerns. Currently, an opportunity is being developed to dramatically reduce remediation costs and to assist in the acceleration of schedules associated with these wastes by deploying a Hot Spot Removal System. Removing the hot spot from the waste site will remove risk driver(s) and enable another, more cost effective process/option/remedial alternative (i.e., capping) to be applied to the remainder of the site. The Hot Spot Removal System consists of a suite of technologies that will be utilized to locate and remove source terms. Components of the system can also be used in a variety of other cleanup activities. This Hot Spot Removal System Description document presents technologies that were considered for possible inclusion in the Hot Spot Removal System, technologies made available to the Hot Spot Removal System, industrial interest in the Hot Spot Removal System''s subsystems, the schedule required for the Hot Spot Removal System, the evaluation of the relevant technologies, and the recommendations for equipment and technologies as stated in the Plan section

CASK/MSC/WP PREPARATION SYSTEM DESCRIPTION DOCUMENT

International Nuclear Information System (INIS)

S. Drummond

2005-01-01

The purpose of this system description document (SDD) is to establish requirements that drive the design of the Cask/MSC/WP preparation system and their bases to allow the design effort to proceed to license application. This SDD is a living document that will be revised at strategic points as the design matures over time. This SDD identifies the requirements and describes the system design, as they exist at this time, with emphasis on those attributes of the design provided to meet the requirements. This SDD has been developed to be an engineering tool for design control. Accordingly, the primary audience and users are design engineers. This type of SDD both leads and trails the design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. This SDD trails the design with regard to the description of the system. The description provided in the SDD is a reflection of the results of the design process to date. This SDD addresses the ''Project Requirements Document'' (PRD) (Canori and Leitner 2003 [DIRS 166275]) requirements. Additional PRD requirements may be cited, as applicable, to drive the design of specific aspects of the system, with justifications provided in the basis. Functional and operational requirements applicable to this system are obtained from the ''Project Functional and Operational Requirements'' (F and OR) (Curry 2004 [DIRS 170557]) document. Other requirements to support the design process have been taken from higher-level requirements documents such as the ''Project Design Criteria Document'' (PDC) (BSC 2004 [DIRS 171599]) and the preclosure safety analyses

Advanced Transport Operating System (ATOPS) color displays software description: MicroVAX system

Science.gov (United States)

Slominski, Christopher J.; Plyler, Valerie E.; Dickson, Richard W.

1992-01-01

This document describes the software created for the Display MicroVAX computer used for the Advanced Transport Operating Systems (ATOPS) project on the Transport Systems Research Vehicle (TSRV). The software delivery of February 27, 1991, known as the 'baseline display system', is the one described in this document. Throughout this publication, module descriptions are presented in a standardized format which contains module purpose, calling sequence, detailed description, and global references. The global references section includes subroutines, functions, and common variables referenced by a particular module. The system described supports the Research Flight Deck (RFD) of the TSRV. The RFD contains eight Cathode Ray Tubes (CRTs) which depict a Primary Flight Display, Navigation Display, System Warning Display, Takeoff Performance Monitoring System Display, and Engine Display.

Integrated environment, safety, and health management system description

International Nuclear Information System (INIS)

Zoghbi, J. G.

2000-01-01

The Integrated Environment, Safety, and Health Management System Description that is presented in this document describes the approach and management systems used to address integrated safety management within the Richland Environmental Restoration Project

Descriptive models for single-jet sluicing of sludge waste

International Nuclear Information System (INIS)

Erian, F.F.; Mahoney, L.A.; Terrones, G.

1997-12-01

Mobilization of sludge waste stored in underground storage tanks can be achieved safely and reliably by sluicing. In the project discussed in this report, the waste in Hanford single-shell Tank 241-C-106 will be mobilized by sluicing, retrieved by a slurry retrieval pump, and transferred via an 1800-ft slurry pipeline to Tank 241-AY-102. A sluicing strategy must be developed that ensures efficient use of the deployed configuration of the sluicing system: the nozzle(s) and the retrieval pump(s). Given a sluicing system configuration in a particular tank, it is desirable to prescribe the sequential locations at which the sludge will be mobilized and retrieved and the rate at which these mobilization and retrieval processes take place. In addition, it is necessary to know whether the retrieved waste slurry meets the requirements for cross-site slurry transport. Some of the physical phenomena that take place during mobilization and retrieval and certain aspects of the sluicing process are described in this report. First, a mathematical model gives (1) an idealized geometrical representation of where, within the confines of a storage tank containing a certain amount of settled waste, sludge can be removed and mobilized; and (2) a quantitative measure of the amount of sludge that can be removed during a sluicing campaign. A model describing an idealized water jet issuing from a circular nozzle located at a given height above a flat surface is also presented in this report. This dynamic water-jet model provides the basis for improving the geometrical sluicing model presented next. In this model the authors assume that the water jet follows a straight trajectory toward a target point on a flat surface. However, the water jet does not follow a straight line in the actual tank, and using the true trajectory will allow a more accurate estimate of the amount of disturbed material. Also, the authors hope that developing accurate force and pressure fields will lead to a better

CASK/MSC/WP PREPARATION SYSTEM DESCRIPTION DOCUMENT

Energy Technology Data Exchange (ETDEWEB)

S. Drummond

2005-04-12

The purpose of this system description document (SDD) is to establish requirements that drive the design of the Cask/MSC/WP preparation system and their bases to allow the design effort to proceed to license application. This SDD is a living document that will be revised at strategic points as the design matures over time. This SDD identifies the requirements and describes the system design, as they exist at this time, with emphasis on those attributes of the design provided to meet the requirements. This SDD has been developed to be an engineering tool for design control. Accordingly, the primary audience and users are design engineers. This type of SDD both leads and trails the design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. This SDD trails the design with regard to the description of the system. The description provided in the SDD is a reflection of the results of the design process to date. This SDD addresses the ''Project Requirements Document'' (PRD) (Canori and Leitner 2003 [DIRS 166275]) requirements. Additional PRD requirements may be cited, as applicable, to drive the design of specific aspects of the system, with justifications provided in the basis. Functional and operational requirements applicable to this system are obtained from the ''Project Functional and Operational Requirements'' (F&OR) (Curry 2004 [DIRS 170557]) document. Other requirements to support the design process have been taken from higher-level requirements documents such as the ''Project Design Criteria Document'' (PDC) (BSC 2004 [DIRS 171599]) and the preclosure safety analyses.

System Design Description PFP Thermal Stabilization

International Nuclear Information System (INIS)

RISENMAY, H.R.

2000-01-01

The purpose of this document is to provide a system design description (SDD) and design basis for the Plutonium Finishing Plant (PFP) Thermal Stabilization project. The chief objective of the SDD is to document the Structures, Systems, and Components (SSCs) that establish and maintain the facility Safety Envelope necessary for normal safe operation of the facility; as identified in the FSAR, the OSRs, and Safety Assessment Documents (SADs). This safety equipment documentation should satisfy guidelines for the SDD given in WHC-SD-CP-TI-18 1, Criteria for Identification and Control of Equipment Necessary for Preservation of the Safety Envelope and Safe Operation of PFP. The basis for operational, alarm response, maintenance, and surveillance procedures are also identified and justified in this document. This document and its appendices address the following elements of the PFP Thermal Stabilization project: Functional and design requirements; Design description; Safety Envelope Analysis; Safety Equipment Class; and Operational, maintenance and surveillance procedures

Technical description of the CANDU nuclear power system

International Nuclear Information System (INIS)

Husseini, S.D.

1977-01-01

The lecture consists of: 1.) KANUPP description: general - Containment- Reactor Cooling System - Moderator Helium System. 2.) Operating experience: Plant Performances (as applicable to Kanupp) - Major failures of primary system - Performance of primary circulating pumps. - Heavy Water Leakage Control. - Radiation Dose Control - Inadvertant Operations. (orig.) [de

Data Description of a System

Directory of Open Access Journals (Sweden)

P. Nevriva

1996-04-01

Full Text Available In this paper, a brief discussion on description of process by memorized data is given. The insight into the problem can offer modified views on optimal control, on data compression at communication systems with respect to information content of message, etc.The idea of process description by memorized data with different information content will be presented here on the classical case study of optimal control: the data based control algorithm (data algorithm, DA gathers data from the controlled process and derives control signal (control from data accumulated in the data base. The implementation of the DA on the ideal computer which is not limited by its speed or capacity of memory is expected for simplicity. Accuracy of the data algorithm is then given by a-priori knowledge of the task and by information exchange between the controlled process and the computer.

Verifying Real-Time Systems using Explicit-time Description Methods

Directory of Open Access Journals (Sweden)

Hao Wang

2009-12-01

Full Text Available Timed model checking has been extensively researched in recent years. Many new formalisms with time extensions and tools based on them have been presented. On the other hand, Explicit-Time Description Methods aim to verify real-time systems with general untimed model checkers. Lamport presented an explicit-time description method using a clock-ticking process (Tick to simulate the passage of time together with a group of global variables for time requirements. This paper proposes a new explicit-time description method with no reliance on global variables. Instead, it uses rendezvous synchronization steps between the Tick process and each system process to simulate time. This new method achieves better modularity and facilitates usage of more complex timing constraints. The two explicit-time description methods are implemented in DIVINE, a well-known distributed-memory model checker. Preliminary experiment results show that our new method, with better modularity, is comparable to Lamport's method with respect to time and memory efficiency.

Non-Markovian spontaneous emission from a single quantum dot

DEFF Research Database (Denmark)

Madsen, Kristian Høeg; Ates, Serkan; Lund-Hansen, Toke

2011-01-01

We observe non-Markovian dynamics of a single quantum dot when tuned into resonance with a cavity mode. Excellent agreement between experiment and theory is observed providing the first quantitative description of such a system.......We observe non-Markovian dynamics of a single quantum dot when tuned into resonance with a cavity mode. Excellent agreement between experiment and theory is observed providing the first quantitative description of such a system....

Integrated Project Management System description

International Nuclear Information System (INIS)

1987-03-01

The Uranium Mill Tailings Remedial Action (UMTRA) Project is a Department of Energy (DOE) designated Major System Acquisition (MSA). To execute and manage the Project mission successfully and to comply with the MSA requirements, the UMTRA Project Office (''Project Office'') has implemented and operates an Integrated Project Management System (IPMS). The Project Office is assisted by the Technical Assistance Contractor's (TAC) Project Integration and Control (PIC) Group in system operation. Each participant, in turn, provides critical input to system operation and reporting requirements. The IPMS provides a uniform structured approach for integrating the work of Project participants. It serves as a tool for planning and control, workload management, performance measurement, and specialized reporting within a standardized format. This system description presents the guidance for its operation. Appendices 1 and 2 contain definitions of commonly used terms and abbreviations and acronyms, respectively. 17 figs., 5 tabs

Application of system-process-goal approach for description of TRIGA RC-1 system

International Nuclear Information System (INIS)

Gadomski, Adam M.

1986-01-01

The new methodology of the goal oriented description of an artificial system is presented. In the SPG approach (System-Process-Goal) it is assumed that the knowledge necessary for achieving the goal is available but it is not ordered or ordered for other purposes. The aim of SPG is to give the description of the analyzed system in form of network by decomposition of goal-system relationships using uniform and mathematical formalism. The SPG approach is useful to build a reactor operator aid system. This paper presents the conception of the application of the SPG approach to the decomposition of TRIGA RC-1 dynamics and for designing of TRIGA diagnostic algorithms. (author)

Computer software design description for the integrated control and data acquisition system LDUA system

International Nuclear Information System (INIS)

Aftanas, B.L.

1998-01-01

This Computer Software Design Description (CSDD) document provides the overview of the software design for all the software that is part of the integrated control and data acquisition system of the Light Duty Utility Arm System (LDUA). It describes the major software components and how they interface. It also references the documents that contain the detailed design description of the components

Electric energy supply systems: description of available technologies

Energy Technology Data Exchange (ETDEWEB)

Eisenhauer, J.L.; Rogers, E.A.; King, J.C.; Stegen, G.E.; Dowis, W.J.

1985-02-01

When comparing coal transportation with electric transmission as a means of delivering electric power, it is desirable to compare entire energy systems rather than just the transportation/transmission components because the requirements of each option may affect the requirements of other energy system components. PNL's assessment consists of two parts. The first part, which is the subject of this document, is a detailed description of the technical, cost, resource and environmental characteristics of each system component and technologies available for these components. The second part is a computer-based model that PNL has developed to simulate construction and operation of alternative system configurations and to compare the performance of these systems under a variety of economic and technical conditions. This document consists of six chapters and two appendices. A more thorough description of coal-based electric energy systems is presented in the Introduction and Chapter 1. Each of the subsequent chapters describes technologies for five system components: Western coal resources (Chapter 2), coal transportation (Chapter 3), coal gasification and gas transmission (Chapter 4), and electric power transmission (Chapter 6).

System description of the Basic MRS System for the FY 1990 Systems Integration Program studies

International Nuclear Information System (INIS)

McKee, R.W.; Young, J.R.; Konzek, G.J.

1991-07-01

This document provides both functional and physical descriptions of a conceptual high-level waste management system defined as a Basic MRS System. Its purpose is to provide a basis for required system computer modeling and system studies initiated in FY 1990 under the Systems Integration Program of the Office of Civilian Radioactive Waste Management Office (OCRWM). Two specific systems studies initiated in FY 1990, the Reference System Performance Evaluation and the Aggregate Receipt Rate Study, utilize the information in this document. The Basic MRS System is the current OCRWM reference high-level radioactive wastes repository system concept. It is designed to accept 3000 MTU per year of spent fuel and 400 equivalent MTU per year of high-level wastes. The Basic MRS System includes a storage-only MRS that provides for a limited amount of commercial spent fuel storage capacity prior to acceptance by the geologic repository for disposal. This document contains both functional descriptions of the processes in the waste management system and physical descriptions of the equipment and facilities necessary for performance of those processes. The basic MRS system contains all system components, from the waste storage facilities of the waste generators to the underground facilities for final disposal of the wastes. The major facilities in the system are the waste generator waste storage facilities, an MRS facility that provides interim storage wastes accepted from the waste generators, a repository facility that packages the wastes and then emplaces them in the geologic repository, and the transportation equipment and facilities for transporting the waste between these major facilities

Collective and boson mapping description of a system of N Josephson junctions in a resonant cavity

International Nuclear Information System (INIS)

Ballesteros, A.; Civitarese, O.; Herranz, F.J.; Reboiro, M.

2003-01-01

A system of N two-level Josephson junctions, interacting between themselves and with a single-mode cavity field, is described in terms of the superposition of fermionic and bosonic excitations. The results of the exact diagonalization are compared with the results of the Tamm-Dancoff approximation and with the results of a boson mapping. It is found that the boson mapping provides a suitable description of the spectrum, sum rules, and response function of the system. The dependence of the results upon the number of junctions, the excitation of the cavity modes, and the coupling strengths is investigated

Cold Vacuum Dryer (CVD) Facility Security System Design Description. System 54

International Nuclear Information System (INIS)

WHITEHURST, R.

2000-01-01

This system design description (SDD) addresses the Cold Vacuum Drying (CVD) Facility security system. The system's primary purpose is to provide reasonable assurance that breaches of security boundaries are detected and assessment information is provided to protective force personnel. In addition, the system is utilized by Operations to support reduced personnel radiation goals and to provide reasonable assurance that only authorized personnel are allowed to enter designated security areas

Construction of the descriptive system for the Assessment of Quality of Life AQoL-6D utility instrument.

Science.gov (United States)

Richardson, Jeffrey R J; Peacock, Stuart J; Hawthorne, Graeme; Iezzi, Angelo; Elsworth, Gerald; Day, Neil A

2012-04-17

Multi attribute utility (MAU) instruments are used to include the health related quality of life (HRQoL) in economic evaluations of health programs. Comparative studies suggest different MAU instruments measure related but different constructs. The objective of this paper is to describe the methods employed to achieve content validity in the descriptive system of the Assessment of Quality of Life (AQoL)-6D, MAU instrument. The AQoL program introduced the use of psychometric methods in the construction of health related MAU instruments. To develop the AQoL-6D we selected 112 items from previous research, focus groups and expert judgment and administered them to 316 members of the public and 302 hospital patients. The search for content validity across a broad spectrum of health states required both formative and reflective modelling. We employed Exploratory Factor Analysis and Structural Equation Modelling (SEM) to meet these dual requirements. The resulting instrument employs 20 items in a multi-tier descriptive system. Latent dimension variables achieve sensitive descriptions of 6 dimensions which, in turn, combine to form a single latent QoL variable. Diagnostic statistics from the SEM analysis are exceptionally good and confirm the hypothesised structure of the model. The AQoL-6D descriptive system has good psychometric properties. They imply that the instrument has achieved construct validity and provides a sensitive description of HRQoL. This means that it may be used with confidence for measuring health related quality of life and that it is a suitable basis for modelling utilities for inclusion in the economic evaluation of health programs.

Using Self-Description to Handle Change in Systems

CERN Document Server

Estrella, Florida; Le Goff, Jean-Marie; McClatchey, Richard; Murray, Steven

2002-01-01

In the web age systems must be flexible, reconfigurable and adaptable in addition to being quick to develop. As a consequence, designing systems to cater for change is becoming not only desirable but required by industry. Allowing systems to be self-describing or description-driven is one way to enable these characteristics. To address the issue of evolvability in designing self-describing systems, this paper proposes a pattern-based, object-oriented, description-driven architecture. The proposed architecture embodies four pillars - first, the adoption of a multi-layered meta-modeling architecture and reflective meta-level architecture, second, the identification of four data modeling relationships that must be made explicit such that they can be examined and modified dynamically, third, the identification of five design patterns which have emerged from practice and have proved essential in providing reusable building blocks for data management, and fourth, the encoding of the structural properties of the fiv...

Cold Vacuum Drying Facility Condensate Collection System Design Description. System 19

International Nuclear Information System (INIS)

PITKOFF, C.C.

2000-01-01

The Cold Vacuum Drying (CVD) Facility of Spent Nuclear Fuel (SNF) provides required process systems, supporting equipment, and facilities to support the SNF Project mission. This system design description (SDD) addresses the Condensate Collection System (CCS). This is a general service system. The CCS begins at the condensate outlet of the general process air-handling unit (AHU) and the condensate outlets for the active process bays AHUs. The system terminates at each condensate collection tank (5 total)

Description, Modelling and Design of Production Systems

DEFF Research Database (Denmark)

Jacobsen, Peter; Rudolph, Carsten

1997-01-01

Design of production systems are rarely an activity in which decision makers in most production companies have much experience. In future, this activity is to be more recurrent due to more and more frequent changes in the production task. Consequently, the decision makers are in need of better...... management tools and methods for description and modelling of production systems supporting the decisions. In this article a structural framework to describe and model production systems will be introduced, and it is shown how the production system of a minor Danish manufacturer of electromechanical...

Green-function description of dense polymeric systems

NARCIS (Netherlands)

Schoot, van der P.P.A.M.

2000-01-01

A self-consistent Green-function description of concentrated polymer solutions and dense polymeric melts is presented. The method, which applies to both uniform and nonuniform systems, is used in this work to calculate the static structure factor of a homogeneous fluid of Gaussian model chains.

Competition between collective and single particle excitations in nuclear structure description

International Nuclear Information System (INIS)

Petrovici, A.N.

1983-01-01

The microscopic description of the quadrupole collective dynamics in even krypton isotopes is presented. A microscopic calculation of Bohr's collective Hamiltonian is used to describe the collective motion in 76 Kr. A single-particle basis calculated in a deformed Woods-Saxon potential leads to the potential energy surface obtained by the Strutinsky renormalization procedure, and to the inertial functions determined in the cranking model approximation. The collective Schroedinger equation is solved numerically to analyse the low-energy, even parity states in 76 Kr. A good agreement between experiment and theory is obtained without specifically adjusting any parameter in the model for this nucleus. Some results regarding statical and dynamical characteristics of sup(74,78,80)Kr isotopes are also presented. The asymmetric rotor model with admixture of two quasiparticles is used to describe the sup(66,68,70)Ge and the sup(64,66)Zn isotopes. The interplay of collective and single particle motions is further investigated by magnetic moment measurements using the method of integral angular correlations perturbed by recoil into gas. The results involve g-factor measurements for 166 Ho, 68 Ge, 64 Zn, 66 Zn and 68 Ga nuclei. Finally, a discussion of further possible improvements and more general developments of the problems under investigation is given. (author)

Standard-D hydrogen monitoring system, system design description

International Nuclear Information System (INIS)

Schneider, T.C.

1996-01-01

During most of the year, it is assumed that the vapor space in the 177 radioactive waste tanks on the Hanford Project site contain a uniform mixture of gases. Several of these waste tanks (currently twenty-five, 6 Double Shell Tanks and 19 Single Shell Tanks) were identified as having the potential for the buildup of gasses to a flammable level. An active ventilation system in the Double Shell Tanks and a passive ventilation system in the Single Shell Tanks provides a method of expelling gasses from the tanks. A gas release from a tank causes a temporary rise in the tank pressure, and a potential for increased concentration of hydrogen gas in the vapor space. The gas is released via the ventilation systems until a uniform gas mixture in the vapor space is once again achieved. The Standard Hydrogen Monitoring System (SHMS) is designed to monitor and quantify the percent hydrogen concentration during these potential gas releases. This document describes the design of the Standard-D Hydrogen Monitoring System, (SHMS-D) and its components as it differs from the original SHMS

Standard-B Hydrogen Monitoring System, system design description

International Nuclear Information System (INIS)

Schneider, T.C.

1995-01-01

During most of the year, it is assumed that the vapor in the 177 radioactive waste tanks on the Hanford Project site contain a uniform mixture of gases. Several of these waste tanks (currently twenty five, 6 Double Shell Tanks and 19 Single Shell Tanks) were identified as having the potential for the buildup of gases to a flammable level. An active ventilation system in the Double Shell Tanks and a passive ventilation system in the Single Shell Tanks provides a method of expelling gases from the tanks. A gas release from a tank causes a temporary rise in the tank pressure, and a potential for increased concentration of hydrogen gas in the vapor space. The gas is released via the ventilation systems until a uniform gas mixture in the vapor space is once again achieved. This document describes the design of the Standard-B Hydrogen Monitoring System, (SHMS) and its components as it differs from the original SHMS. The differences are derived from changes made to improve the system performance but not implemented in all the installed enclosures

System description: Isabelle/jEdit in 2014

Directory of Open Access Journals (Sweden)

Makarius Wenzel

2014-10-01

Full Text Available This is an updated system description for Isabelle/jEdit, according to the official release Isabelle2014 (August 2014. The following new PIDE concepts are explained: asynchronous print functions and document overlays, syntactic and semantic completion, editor navigation, management of auxiliary files within the document-model.

On the thermodynamic description of real systems

International Nuclear Information System (INIS)

Bernardes, N.

1984-01-01

A new method of approach to the theory of the thermodynamic properties of real systems is proposed, to include interactions among the constituent particles of the system. The method consists in obtaining the entropy of a real system from the entropy of the corresponding ideal system by a translation in the internal energy and other relevant extensive variables. The usefulness of the method is displayed by application to the cases of: (i) real gases, and (ii) spin paramagnetism with interactions among spins. It is shown that this description corresponds to a generalization of the molecular field approximation. (Author) [pt

CDMS: CAD data set system design description. Revision 1

International Nuclear Information System (INIS)

Gray, E.L.

1994-01-01

This document is intended to formalize the program design of the CAD Data Set Management System (CDMS) and to be the vehicle to communicate the design to the Engineering, Design Services, and Configuration Management organizations and the WHC IRM Analysts/Programmers. The SDD shows how the software system will be structured to satisfy the requirements identified in the WHC-SD-GN-CSRS-30005 CDMS Software Requirement Specification (SRS). It is a description of the software structure, software components, interfaces, and data that make up the CDMS System. The design descriptions contained within this document will describe in detail the software product that will be developed to assist the aforementioned organizations for the express purpose of managing CAD data sets associated with released drawings, replacing the existing locally developed system and laying the foundation for automating the configuration management

Construction of the descriptive system for the assessment of quality of life AQoL-6D utility instrument

Directory of Open Access Journals (Sweden)

Richardson Jeffrey RJ

2012-04-01

Full Text Available Abstract Background Multi attribute utility (MAU instruments are used to include the health related quality of life (HRQoL in economic evaluations of health programs. Comparative studies suggest different MAU instruments measure related but different constructs. The objective of this paper is to describe the methods employed to achieve content validity in the descriptive system of the Assessment of Quality of Life (AQoL-6D, MAU instrument. Methods The AQoL program introduced the use of psychometric methods in the construction of health related MAU instruments. To develop the AQoL-6D we selected 112 items from previous research, focus groups and expert judgment and administered them to 316 members of the public and 302 hospital patients. The search for content validity across a broad spectrum of health states required both formative and reflective modelling. We employed Exploratory Factor Analysis and Structural Equation Modelling (SEM to meet these dual requirements. Results and Discussion The resulting instrument employs 20 items in a multi-tier descriptive system. Latent dimension variables achieve sensitive descriptions of 6 dimensions which, in turn, combine to form a single latent QoL variable. Diagnostic statistics from the SEM analysis are exceptionally good and confirm the hypothesised structure of the model. Conclusions The AQoL-6D descriptive system has good psychometric properties. They imply that the instrument has achieved construct validity and provides a sensitive description of HRQoL. This means that it may be used with confidence for measuring health related quality of life and that it is a suitable basis for modelling utilities for inclusion in the economic evaluation of health programs.

Technical description of the Swedish natural gas distribution system

Energy Technology Data Exchange (ETDEWEB)

Nilsson, Ronny [KM Miljoeteknik AB (Sweden)

1997-06-01

This description of the Swedish distribution network has been produced to provide information for distribution companies, trade organisations, etc., who have an interest in getting a clear understanding of the technical design and standards, technical directives, etc., which have served as guidance in the development. The technical description covers the piping system from a measuring and regulating station (MR station) up to the consumer`s substation, however, only sections with a maximum operating pressure of 4 bar. By way of introduction, the description contains introductory information on supply channels, consumption patterns and the principal design of the high pressure network in Sweden 10 refs, 10 figs, 1 tab

44 CFR 334.5 - GMR system description.

Science.gov (United States)

2010-10-01

... problems. (b) Stage 2, Crisis Management. During the crisis management stage, GMR plans are reviewed and... developed). For example, a Federal department or agency might divide “Crisis Management” into two, three, or... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false GMR system description. 334.5...

Cold Vacuum Drying (CVD) Electrical System Design Description

International Nuclear Information System (INIS)

SINGH, G.

2000-01-01

This system design description (SDD) provides a technical explanation of the design and operation of the electrical system for the Cold Vacuum Drying Facility (CVDF). This SDD also identifies the requirements, and the basis for the requirements and details on how the requirements have been implemented in the design and construction of the facility. This SDD also provides general guidance for the surveillance, testing, and maintenance of this system

Single particle detecting telescope system

International Nuclear Information System (INIS)

Yamamoto, I.; Tomiyama, T.; Iga, Y.; Komatsubara, T.; Kanada, M.; Yamashita, Y.; Wada, T.; Furukawa, S.

1981-01-01

We constructed the single particle detecting telescope system for detecting a fractionally charged particle. The telescope consists of position detecting counters, wall-less multi-cell chambers, single detecting circuits and microcomputer system as data I/0 processor. Especially, a frequency of double particle is compared the case of the single particle detecting with the case of an ordinary measurement

Rock Visualization System. Technical description (RVS v.3.5)

Energy Technology Data Exchange (ETDEWEB)

Curtis, P.; Elfstroem, M.; Markstroem, I. [FB Engineering, Goeteborg (Sweden)

2004-03-01

The Rock Visualization System (RVS) has been developed by SKB for use in visualizing geological and engineering data in 3D. The purpose of this report is to provide a technical description of RVS aimed at potential program users and interested parties as well as fulfilling the function of a more general RVS reference that can be cited when writing other technical reports. It is a description of RVS version 3.5. Updated versions of this report or addenda will be made available following further development of RVS and the release of subsequent versions of the program. The report covers the following main items: Technical description of the program with illustrations and examples; Limitations of the program and of functionality. For most RVS functions step-by-step tutorials are available describing how a particular function can be used to carryout a specific task. A complete set of updated tutorials is issued with each new version release of the RVS program. However, the tutorials do not cover all the possible uses of all the individual functions but rather give an overall view of their functionality. A detailed description of every RVS function and how it can be used is included in the RVS online Help system.

Rock Visualization System. Technical description (RVS v.3.5)

International Nuclear Information System (INIS)

Curtis, P.; Elfstroem, M.; Markstroem, I.

2004-03-01

The Rock Visualization System (RVS) has been developed by SKB for use in visualizing geological and engineering data in 3D. The purpose of this report is to provide a technical description of RVS aimed at potential program users and interested parties as well as fulfilling the function of a more general RVS reference that can be cited when writing other technical reports. It is a description of RVS version 3.5. Updated versions of this report or addenda will be made available following further development of RVS and the release of subsequent versions of the program. The report covers the following main items: Technical description of the program with illustrations and examples; Limitations of the program and of functionality. For most RVS functions step-by-step tutorials are available describing how a particular function can be used to carryout a specific task. A complete set of updated tutorials is issued with each new version release of the RVS program. However, the tutorials do not cover all the possible uses of all the individual functions but rather give an overall view of their functionality. A detailed description of every RVS function and how it can be used is included in the RVS online Help system

The Norwegian Electric Power System - System Description and Future Developments; Norsk kraftforsyning - dagens system og fremtidig utvikling

Energy Technology Data Exchange (ETDEWEB)

Hagen, Janne Merete; Nystuen, Kjell Olav; Fridheim, Haavard; Rutledal, Frode

2000-09-01

This report presents a description of the present Norwegian electric power system, as well as a discussion of emerging trends and future developments in this system. The report provides the basis for FFI's current vulnerability analysis of the electric power system. Norway's electric power system is getting increasingly complex, due to a large-scale implementation of electronic components and information systems. Workforce reductions and efficiency improvements dominate the development of the electric power sector. Norway is also becoming increasingly dependent on foreign power sources. These trends provide for an entirely different electric power system than just a few years ago. Also, these trends make it virtually impossible to present a ''static'' description of the system. Thus, the report also contains a scenario, describing possible future developments of the system until 2010. (author)

Advanced Transport Operating System (ATOPS) control display unit software description

Science.gov (United States)

Slominski, Christopher J.; Parks, Mark A.; Debure, Kelly R.; Heaphy, William J.

1992-01-01

The software created for the Control Display Units (CDUs), used for the Advanced Transport Operating Systems (ATOPS) project, on the Transport Systems Research Vehicle (TSRV) is described. Module descriptions are presented in a standardized format which contains module purpose, calling sequence, a detailed description, and global references. The global reference section includes subroutines, functions, and common variables referenced by a particular module. The CDUs, one for the pilot and one for the copilot, are used for flight management purposes. Operations performed with the CDU affects the aircraft's guidance, navigation, and display software.

TD-S-HF single determinantal reaction theory and the description of many-body processes, including fission

International Nuclear Information System (INIS)

Griffin, J.J.; Lichtner, P.C.; Dworzecka, M.; Kan, K.K.

1979-01-01

The restrictions implied for the time dependent many-body reaction theory by the (TDHF) single determinantal assumption are explored by constructive analysis. A restructured TD-S-HF reaction theory is modelled, not after the initial-value form of the Schroedinger reaction theory, but after the (fully equivalent) S-matrix form, under the conditions that only self-consistent TDHF solutions occur in the theory, every wave function obeys the fundamental statistical interpretation of quantum mechanics, and the theory reduces to the exact Schroedinger theory for exact solutions which are single determinantal. All of these conditions can be accomodated provided that the theory is interpreted on a time-averaged basis, i.e., physical constants of the Schroedinger theory which are time-dependent in the TDHF theory, are interpreted in TD-S-HF in terms of their time averaged values. The resulting reaction theory, although formulated heuristically, prescribes a well defined and unambiguous calculational program which, although somewhat more demanding technically than the conventional initial-value TDHF method, is nevertheless more consonant with first principles, structurally and mechanistically. For its physical predictions do not depend upon the precise location of the distant measuring apparatus, and are in no way influenced by the spurious cross channel correlations which arise whenever the description of many reaction channels is imposed upon one single-determinantal solution. For nuclear structure physics, the TDHF-eigenfunctions provide the first plausible description of exact eigenstates in the time-dependent framework; moreover, they are unencumbered by any restriction to small amplitudes. 14 references

International safeguards data management system. System description: Version 1.1.; Release PLI 82

International Nuclear Information System (INIS)

Argentesi, T.; Casilli, T.; Costantini, L.; Dondi, M.G.; Franklin, M.

1982-01-01

This document describes a nuclear material accountancy system which has been developed using the ADABAS data base management system and is implemented on the JRC-Ispra computer. Throughout the report, the data base system is referred to as ''ISADAM'', i.e. International Safeguards Data Management System. The system provides tools for a safeguards authority to decide whether an operators MUF (Material Unaccounted For) can be accounted for as an accumulation of operator measurement errors. The principle objective of the applications programs described here is to provide a variance analysis of MUF in which the variance of MUF is computed as a function of the accounting declarations and the error characteristics of the operator measurement system. A overview of ISADAM is presented; then, a detailed description of the processing applied by the system is given. A description of the parameter information required by the four autonomous programs ISADAM is presented. In developing ISADAM, one of the prime factors taken into consideration was the ease with which it could be used

Computer system design description for SY-101 hydrogen mitigation test project data acquisition and control system (DACS-1)

International Nuclear Information System (INIS)

Ermi, A.M.

1997-01-01

Description of the Proposed Activity/REPORTABLE OCCURRENCE or PIAB: This ECN changes the computer systems design description support document describing the computers system used to control, monitor and archive the processes and outputs associated with the Hydrogen Mitigation Test Pump installed in SY-101. There is no new activity or procedure associated with the updating of this reference document. The updating of this computer system design description maintains an agreed upon documentation program initiated within the test program and carried into operations at time of turnover to maintain configuration control as outlined by design authority practicing guidelines. There are no new credible failure modes associated with the updating of information in a support description document. The failure analysis of each change was reviewed at the time of implementation of the Systems Change Request for all the processes changed. This document simply provides a history of implementation and current system status

System Description for Tank 241-AZ-101 Waste Retrieval Data Acquisition System

International Nuclear Information System (INIS)

ROMERO, S.G.

2000-01-01

The proposed activity provides the description of the Data Acquisition System for Tank 241-AZ-101. This description is documented in HNF-5572, Tank 241-AZ-101 Waste Retrieval Data Acquisition System (DAS). This activity supports the planned mixer pump tests for Tank 241-AZ-101. Tank 241-AZ-101 has been selected for the first full-scale demonstration of a mixer pump system. The tank currently holds over 960,000 gallons of neutralized current acid waste, including approximately 12.7 inches of settling solids (sludge) at the bottom of the tank. As described in Addendum 4 of the FSAR (LMHC 2000a), two 300 HP mixer pumps with associated measurement and monitoring equipment have been installed in Tank 241-AZ-101. The purpose of the Tank 241-AZ-101 retrieval system Data Acquisition System (DAS) is to provide monitoring and data acquisition of key parameters in order to confirm the effectiveness of the mixer pumps utilized for suspending solids in the tank. The suspension of solids in Tank 241-AZ-101 is necessary for pretreatment of the neutralized current acid waste and eventual disposal as glass via the Hanford Waste Vitrification Plant. HNF-5572 provides a basic description of the Tank 241-AZ-101 retrieval system DAS, including the field instrumentation and application software. The DAS is provided to fulfill requirements for data collection and monitoring. This document is not an operations procedure or is it intended to describe the mixing operation. This USQ screening provides evaluation of HNF-5572 (Revision 1) including the changes as documented on ECN 654001. The changes include (1) add information on historical trending and data backup, (2) modify DAS I/O list in Appendix E to reflect actual conditions in the field, and (3) delete IP address in Appendix F per Lockheed Martin Services, Inc. request

Cold Vacuum Drying Instrument Air System Design Description. System 12

International Nuclear Information System (INIS)

SHAPLEY, B.J.; TRAN, Y.S.

2000-01-01

This system design description (SDD) addresses the instrument air (IA) system of the spent nuclear fuel (SNF). This IA system provides instrument quality air to the Cold Vacuum Drying (CVD) Facility. The IA system is a general service system that supports the operation of the heating, ventilation, and air conditioning (HVAC) system, the process equipment skids, and process instruments in the CVD Facility. The following discussion is limited to the compressor, dryer, piping, and valving that provide the IA as shown in Drawings H-1-82222, Cold Vacuum Drying Facility Mechanical Utilities Compressed and Instrument Air PandID, and H-1.82161, Cold Vacuum Drying Facility Process Equipment Skid PandID MCO/Cusk Interface. Figure 1-1 shows the physical location of the 1A system in the CVD Facility

A consistent description of kinetics and hydrodynamics of quantum Bose-systems

Directory of Open Access Journals (Sweden)

P.A.Hlushak

2004-01-01

Full Text Available A consistent approach to the description of kinetics and hydrodynamics of many-Boson systems is proposed. The generalized transport equations for strongly and weakly nonequilibrium Bose systems are obtained. Here we use the method of nonequilibrium statistical operator by D.N. Zubarev. New equations for the time distribution function of the quantum Bose system with a separate contribution from both the kinetic and potential energies of particle interactions are obtained. The generalized transport coefficients are determined accounting for the consistent description of kinetic and hydrodynamic processes.

Cold Vacuum Drying Facility Crane and Hoist System Design Description. System 14

International Nuclear Information System (INIS)

TRAN, Y.S.

2000-01-01

This system design description (SDD) is for the Cold Vacuum Drying (CVD) Facility overhead crane and hoist system. The overhead crane and hoist system is a general service system. It is located in the process bays of the CVD Facility, supports the processes required to drain the water and dry the spent nuclear fuel (SNF) contained in the multi-canister overpacks (MCOs) after they have been removed from the K-Basins. The location of the system in the process bay is shown

Irreducible descriptive sets of attributes for information systems

KAUST Repository

Moshkov, Mikhail; Skowron, Andrzej; Suraj, Zbigniew

2010-01-01

. An irreducible descriptive set for the considered information system S is a minimal (relative to the inclusion) set B of attributes which defines exactly the set Ext(S) by means of true and realizable rules constructed over attributes from the considered set B

Integrated Project Management System description

International Nuclear Information System (INIS)

1994-09-01

The Integrated Program Management System (IPMS) Description is a ''working'' document that describes the work processes of the Uranium Mill Tailings Remedial Action Project Office (UMTRA) and IPMS Group. This document has undergone many revisions since the UMTRA Project began; this revision not only updates the work processes but more clearly explains the relationships between the Project Office, contractors, and other participants. The work process flow style has been revised to better describe Project work and the relationships of participants. For each work process, more background and guidance on ''why'' and ''what is expected'' is given. For example, a description of activity data sheets has been added in the work organization and the Project performance and reporting processes, as well as additional detail about the federal budget process and funding management and improved flow charts and explanations of cost and schedule management. A chapter has been added describing the Cost Reduction/Productivity Improvement Program. The Change Control Board (CCB) procedures (Appendix A) have been updated. Project critical issues meeting (PCIM) procedures have been added as Appendix B. Budget risk assessment meeting procedures have been added as Appendix C. These appendices are written to act as stand-alone documentation for each process. As the procedures are improved and updated, the documentation can be updated separately

WRAP Module 1 data management system (DMS) software design description (SDD)

International Nuclear Information System (INIS)

Weidert, J.R.

1996-01-01

Revision 2 of the Waste Receiving and Processing (WRAP) Module 1 Data Management System (DMS) Preliminary Software Design Description (PSDD) provides a high-level design description of the system. The WRAP 1 DMS is required to collect, store, and report data related to certification, tracking, packaging, repackaging, processing, and shipment of waste processed or stored at the WRAP 1 facility. The WRAP 1 DMS SDD is used as the primary medium for communication software design information. This release provides design descriptions for the following process modules produced under Phase 1 of the development effort: Receiving Drum or Box Containers Process Routing and Picklists; Waste Inventory by Location and/or Container Relationships; LLW Process Glovebox Facility Radiologic Material Inventory Check (partial); Shipping (partial production); Drum or Box NDE Operations; and Drum or Box NDA Operations Data Review (partial production). In addition, design descriptions are included for the following process modules scheduled for development under Phases 2 and 3: Activity Comment; LLW RWM Glovebox Sample Management; TRU Process Glovebox; TRU RWM Glovebox; and TRUPACT Processing. Detailed design descriptions for Reports and Facility Metrics have also been provided for in Revision 2 of this document

System design description for sampling fuel in K basins

International Nuclear Information System (INIS)

Baker, R.B.

1996-01-01

This System Design Description provides: (1) statements of the Spent Nuclear Fuel Projects (SNFP) needs requiring sampling of fuel in the K East and K West Basins, (2) the sampling equipment functions and requirements, (3) a general work plan and the design logic being followed to develop the equipment, and (4) a summary description of the design for the sampling equipment. The report summarizes the integrated application of both the subject equipment and the canister sludge sampler in near-term characterization campaigns at K Basins

Engineer/constructor description of work for Tank 241-SY-102 retrieval system, project W-211, initial tank retrieval systems

International Nuclear Information System (INIS)

Rieck, C.A.

1996-02-01

This document provides a description of work for the design and construction of a waste retrieval system for Tank 241-SY-102. The description of work includes a working estimate and schedule, as well as a narrative description and sketches of the waste retrieval system. The working estimate and schedule are within the established baselines for the Tank 241-SY-102 retrieval system. The technical baseline is provided in Functional Design Criteria, WHC-SD-W211-FDC-001, Revision 2

Demonstration Advanced Avionics System (DAAS) function description

Science.gov (United States)

Bailey, A. J.; Bailey, D. G.; Gaabo, R. J.; Lahn, T. G.; Larson, J. C.; Peterson, E. M.; Schuck, J. W.; Rodgers, D. L.; Wroblewski, K. A.

1982-01-01

The Demonstration Advanced Avionics System, DAAS, is an integrated avionics system utilizing microprocessor technologies, data busing, and shared displays for demonstrating the potential of these technologies in improving the safety and utility of general aviation operations in the late 1980's and beyond. Major hardware elements of the DAAS include a functionally distributed microcomputer complex, an integrated data control center, an electronic horizontal situation indicator, and a radio adaptor unit. All processing and display resources are interconnected by an IEEE-488 bus in order to enhance the overall system effectiveness, reliability, modularity and maintainability. A detail description of the DAAS architecture, the DAAS hardware, and the DAAS functions is presented. The system is designed for installation and flight test in a NASA Cessna 402-B aircraft.

System design description PFP thermal stabilization

International Nuclear Information System (INIS)

RISENMAY, H.R.

1998-01-01

The purpose of this document is to provide a system design description and design basis for the Plutonium Finishing P1ant (PFP) Thermal Stabilization project. The sources of material for this project are residues scraped from glovebox floors and materials already stored in vault storage that need further stabilizing to meet the 3013 storage requirements. Stabilizing this material will promote long term storage and reduced worker exposure. This document addresses: function design, equipment, and safety requirements for thermal stabilization of plutonium residues and oxides

An Automated Weather Research and Forecasting (WRF)-Based Nowcasting System: Software Description

Science.gov (United States)

2013-10-01

14. ABSTRACT A Web service /Web interface software package has been engineered to address the need for an automated means to run the Weather Research...An Automated Weather Research and Forecasting (WRF)- Based Nowcasting System: Software Description by Stephen F. Kirby, Brian P. Reen, and...Based Nowcasting System: Software Description Stephen F. Kirby, Brian P. Reen, and Robert E. Dumais Jr. Computational and Information Sciences

Quantum description of microscopic and macroscopic systems: Old problems and recent investigations

International Nuclear Information System (INIS)

Ghirardi, G.C.

1986-04-01

We review some open problems and some proposed solutions which are encountered in the quantum description of the microscopic systems, of the macroscopic ones, and of the interactions between these two types of objects. We describe a recent attempt allowing a unified description of all phenomena, reproducing the quantum mechanical situation for microscopic systems and inducing in a completely consistent way the classical behaviour of macro object and the phenomena of wave packet reduction in the system-apparatus interaction. (author)

Description of disintegration in a three-body system

CERN Document Server

Takibaev, N Z

2000-01-01

In the frame of approach based on the effective potential of interaction between constituents, description of inelastic transition, in particularly, the processes of system disintegration. Relationship is shown between the approach results and those of the theory of final state interaction where coefficients of reaction gaining factor are determined. (author)

Common-Ground-Type Transformerless Inverters for Single-Phase Solar Photovoltaic Systems

DEFF Research Database (Denmark)

Siwakoti, Yam Prasad; Blaabjerg, Frede

2018-01-01

This paper proposes a family of novel flying capacitor transformerless inverters for single-phase photovoltaic (PV) systems. Each of the new topologies proposed is based on a flying capacitor principle and requires only four power switches and/or diodes, one capacitor, and a small filter at the o......This paper proposes a family of novel flying capacitor transformerless inverters for single-phase photovoltaic (PV) systems. Each of the new topologies proposed is based on a flying capacitor principle and requires only four power switches and/or diodes, one capacitor, and a small filter...... at the output stage. A simple unipolar sinusoidal pulse width modulation technique is used to modulate the inverter to minimize the switching loss, output current ripple, and the filter requirements. In general, the main advantages of the new inverter topologies are: 1) the negative polarity of the PV...... description of the operating principle with modulation techniques, design guidelines, and comprehensive comparisons is presented to reveal the properties and limitations of each topology in detail. Finally, experimental results of 1-kVA prototypes are presented to prove the concept and theoretical analysis...

Design description of the Tangaye Village photovoltaic power system

Science.gov (United States)

Martz, J. E.; Ratajczak, A. F.

1982-01-01

The engineering design of a stand alone photovoltaic (PV) powered grain mill and water pump for the village of Tangaye, Upper Volta is described. The socioeconomic effects of reducing the time required by women in rural areas for drawing water and grinding grain were studied. The suitability of photovoltaic technology for use in rural areas by people of limited technical training was demonstrated. The PV system consists of a 1.8-kW (peak) solar cell array, 540 ampere hours of battery storage, instrumentation, automatic controls, and a data collection and storage system. The PV system is situated near an improved village well and supplies d.c. power to a grain mill and a water pump. The array is located in a fenced area and the mill, battery, instruments, controls, and data system are in a mill building. A water storage tank is located near the well. The system employs automatic controls which provide battery charge regulation and system over and under voltage protection. This report includes descriptions of the engineering design of the system and of the load that it serves; a discussion of PV array and battery sizing methodology; descriptions of the mechanical and electrical designs including the array, battery, controls, and instrumentation; and a discussion of the safety features. The system became operational on March 1, 1979.

System Description for the KW Basin Integrated Water Treatment System (IWTS) (70.3)

International Nuclear Information System (INIS)

DERUSSEAU, R.R.

2000-01-01

This is a description of the system that collects and processes the sludge and radioactive ions released by the spent nuclear fuel (SNF) processing operations conducted in the 105 KW Basin. The system screens, settles, filters, and conditions the basin water for reuse. Sludge and most radioactive ions are removed before the water is distributed back to the basin pool. This system is part of the Spent Nuclear Fuel Project (SNFP)

Rock Visualization System. Technical description (RVS version 3.8)

International Nuclear Information System (INIS)

Curtis, P.; Elfstroem, M.; Markstroem, I.

2007-06-01

The Rock Visualization System (RVS) has been developed by SKB for use in visualizing geological and engineering data in 3D. The purpose of this report is to provide a technical description of RVS aimed at potential program users and interested parties as well as fulfilling the function of a more general RVS reference that can be cited when writing other technical reports. The report describes RVS version 4.0. Updated versions of this report or addenda will be made available following further development of RVS and the release of subsequent versions of the program. The report covers the following main items: Technical description of the program with illustrations and examples. Limitations of the program and of functionality. For most RVS functions step-by-step tutorials are available describing how a particular function can be used to carry out a specific task. A complete set of updated tutorials is issued with each new version release of the RVS program. However, the tutorials do not cover all the possible uses of all the individual functions but rather give an overall view of their functionality. A detailed description of every RVS function and how it can be used is included in the RVS online Help system

Rock Visualization System. Technical description (RVS version 3.8)

Energy Technology Data Exchange (ETDEWEB)

Curtis, P.; Elfstroem, M.; Markstroem, I. [FB Engineering, Goeteborg (Sweden)

2005-04-01

The Rock Visualization System (RVS) has been developed by SKB for use in visualizing geological and engineering data in 3D. The purpose of this report is to provide a technical description of RVS aimed at potential program users and interested parties as well as fulfilling the function of a more general RVS reference that can be cited when writing other technical reports. The report describes RVS version 3.8. Updated versions of this report or addenda will be made available following further development of RVS and the release of subsequent versions of the program. The report covers the following main items: Technical description of the program with illustrations and examples. Limitations of the program and of functionality. For most RVS functions step-by-step tutorials are available describing how a particular function can be used to carryout a specific task. A complete set of updated tutorials is issued with each new version release of the RVS program. However, the tutorials do not cover all the possible uses of all the individual functions but rather give an overall view of their functionality. A detailed description of every RVS function and how it can be used is included in the RVS online Help system.

Rock Visualization System. Technical description (RVS version 3.8)

Energy Technology Data Exchange (ETDEWEB)

Curtis, P.; Elfstroem, M.; Markstroem, I. [Golder Associates AB (Sweden)

2007-06-15

The Rock Visualization System (RVS) has been developed by SKB for use in visualizing geological and engineering data in 3D. The purpose of this report is to provide a technical description of RVS aimed at potential program users and interested parties as well as fulfilling the function of a more general RVS reference that can be cited when writing other technical reports. The report describes RVS version 4.0. Updated versions of this report or addenda will be made available following further development of RVS and the release of subsequent versions of the program. The report covers the following main items: Technical description of the program with illustrations and examples. Limitations of the program and of functionality. For most RVS functions step-by-step tutorials are available describing how a particular function can be used to carry out a specific task. A complete set of updated tutorials is issued with each new version release of the RVS program. However, the tutorials do not cover all the possible uses of all the individual functions but rather give an overall view of their functionality. A detailed description of every RVS function and how it can be used is included in the RVS online Help system.

Rock Visualization System. Technical description (RVS version 3.8)

International Nuclear Information System (INIS)

Curtis, P.; Elfstroem, M.; Markstroem, I.

2005-04-01

The Rock Visualization System (RVS) has been developed by SKB for use in visualizing geological and engineering data in 3D. The purpose of this report is to provide a technical description of RVS aimed at potential program users and interested parties as well as fulfilling the function of a more general RVS reference that can be cited when writing other technical reports. The report describes RVS version 3.8. Updated versions of this report or addenda will be made available following further development of RVS and the release of subsequent versions of the program. The report covers the following main items: Technical description of the program with illustrations and examples. Limitations of the program and of functionality. For most RVS functions step-by-step tutorials are available describing how a particular function can be used to carryout a specific task. A complete set of updated tutorials is issued with each new version release of the RVS program. However, the tutorials do not cover all the possible uses of all the individual functions but rather give an overall view of their functionality. A detailed description of every RVS function and how it can be used is included in the RVS online Help system

Semantic Web Compatible Names and Descriptions for Organisms

Science.gov (United States)

Wang, H.; Wilson, N.; McGuinness, D. L.

2012-12-01

Modern scientific names are critical for understanding the biological literature and provide a valuable way to understand evolutionary relationships. To validly publish a name, a description is required to separate the described group of organisms from those described by other names at the same level of the taxonomic hierarchy. The frequent revision of descriptions due to new evolutionary evidence has lead to situations where a single given scientific name may over time have multiple descriptions associated with it and a given published description may apply to multiple scientific names. Because of these many-to-many relationships between scientific names and descriptions, the usage of scientific names as a proxy for descriptions is inevitably ambiguous. Another issue lies in the fact that the precise application of scientific names often requires careful microscopic work, or increasingly, genetic sequencing, as scientific names are focused on the evolutionary relatedness between and within named groups such as species, genera, families, etc. This is problematic to many audiences, especially field biologists, who often do not have access to the instruments and tools required to make identifications on a microscopic or genetic basis. To better connect scientific names to descriptions and find a more convenient way to support computer assisted identification, we proposed the Semantic Vernacular System, a novel naming system that creates named, machine-interpretable descriptions for groups of organisms, and is compatible with the Semantic Web. Unlike the evolutionary relationship based scientific naming system, it emphasizes the observable features of organisms. By independently naming the descriptions composed of sets of observational features, as well as maintaining connections to scientific names, it preserves the observational data used to identify organisms. The system is designed to support a peer-review mechanism for creating new names, and uses a controlled

Preparation of plant and system design description documents

International Nuclear Information System (INIS)

1989-01-01

This standard prescribes the purpose, scope, organization, and content of plant design requirements (PDR) documents and system design descriptions (SDDs), to provide a unified approach to their preparation and use by a project as the principal means to establish the plant design requirements and to establish, describe, and control the individual system designs from conception and throughout the lifetime of the plant. The Electric Power Research Institute's Advanced Light Water Reactor (LWR) Requirements Document should be considered for LWR plants

Blind Decoding of Multiple Description Codes over OFDM Systems via Sequential Monte Carlo

Directory of Open Access Journals (Sweden)

Guo Dong

2005-01-01

Full Text Available We consider the problem of transmitting a continuous source through an OFDM system. Multiple description scalar quantization (MDSQ is applied to the source signal, resulting in two correlated source descriptions. The two descriptions are then OFDM modulated and transmitted through two parallel frequency-selective fading channels. At the receiver, a blind turbo receiver is developed for joint OFDM demodulation and MDSQ decoding. Transformation of the extrinsic information of the two descriptions are exchanged between each other to improve system performance. A blind soft-input soft-output OFDM detector is developed, which is based on the techniques of importance sampling and resampling. Such a detector is capable of exchanging the so-called extrinsic information with the other component in the above turbo receiver, and successively improving the overall receiver performance. Finally, we also treat channel-coded systems, and a novel blind turbo receiver is developed for joint demodulation, channel decoding, and MDSQ source decoding.

Systems Biology Graphical Notation: Process Description language Level 1 Version 1.3.

Science.gov (United States)

Moodie, Stuart; Le Novère, Nicolas; Demir, Emek; Mi, Huaiyu; Villéger, Alice

2015-09-04

The Systems Biological Graphical Notation (SBGN) is an international community effort for standardized graphical representations of biological pathways and networks. The goal of SBGN is to provide unambiguous pathway and network maps for readers with different scientific backgrounds as well as to support efficient and accurate exchange of biological knowledge between different research communities, industry, and other players in systems biology. Three SBGN languages, Process Description (PD), Entity Relationship (ER) and Activity Flow (AF), allow for the representation of different aspects of biological and biochemical systems at different levels of detail. The SBGN Process Description language represents biological entities and processes between these entities within a network. SBGN PD focuses on the mechanistic description and temporal dependencies of biological interactions and transformations. The nodes (elements) are split into entity nodes describing, e.g., metabolites, proteins, genes and complexes, and process nodes describing, e.g., reactions and associations. The edges (connections) provide descriptions of relationships (or influences) between the nodes, such as consumption, production, stimulation and inhibition. Among all three languages of SBGN, PD is the closest to metabolic and regulatory pathways in biological literature and textbooks, but its well-defined semantics offer a superior precision in expressing biological knowledge.

A Fundamental Scale of Descriptions for Analyzing Information Content of Communication Systems

Directory of Open Access Journals (Sweden)

Gerardo Febres

2015-03-01

Full Text Available The complexity of the description of a system is a function of the entropy of its symbolic description. Prior to computing the entropy of the system’s description, an observation scale has to be assumed. In texts written in artificial and natural languages, typical scales are binary, characters, and words. However, considering languages as structures built around certain preconceived set of symbols, like words or characters, limits the level of complexity that can be revealed analytically. This study introduces the notion of the fundamental description scale to analyze the essence of the structure of a language. The concept of Fundamental Scale is tested for English and musical instrument digital interface (MIDI music texts using an algorithm developed to split a text in a collection of sets of symbols that minimizes the observed entropy of the system. This Fundamental Scale reflects more details of the complexity of the language than using bits, characters or words. Results show that this Fundamental Scale allows to compare completely different languages, such as English and MIDI coded music regarding its structural entropy. This comparative power facilitates the study of the complexity of the structure of different communication systems.

Description langugage for the modelling and analysis of temporal change of instrumentation and control system structures

International Nuclear Information System (INIS)

Goering, Markus Heinrich

2013-01-01

The utilisation of computer-based I and C, as a result of the technological advancements in the computer industry, represents an up-to-date challenge for I and C engineers in nuclear power plants throughout the world. In comparison with the time-proven, hard-wired I and C, the engineering must consider the novel characteristics of computer-based technology during the implementation, these are primarily constituted by higher performance and the utilisation of software. On one hand, this allows for implementing more complex I and C functions and integrating several I and C functions on to single components, although on the other hand, the minimisation of the CCF probability is of high priority to the engineering. Furthermore, the engineering must take the implementation of the deterministic safety concept for the I and C design into consideration. This includes engineering the redundancy, diversity, physical separation, and independence design features, and is complemented by the analysis of the I and C design with respect to the superposition of pre-defined event sequences and postulated failure combinations, so as to secure the safe operation of the nuclear power plant. The focus of this thesis is on the basic principles of engineering, i.e. description languages and methods, which the engineering relies on for a highly qualitative and efficient computer-based I and C implementation. The analysis of the deterministic safety concept and computer-based I and C characteristics yields the relevant technical requirements for the engineering, these are combined with the general structuring principles of standard IEC 81346 and the extended description language evaluation criteria, which are based on the guideline VDI/VDE-3681, resulting in target criteria for evaluating description languages. The analysis and comparison of existing description languages reveals that no description language satisfactorily fulfils all target criteria, which is constituted in the

Description langugage for the modelling and analysis of temporal change of instrumentation and control system structures

Energy Technology Data Exchange (ETDEWEB)

Goering, Markus Heinrich

2013-10-25

The utilisation of computer-based I and C, as a result of the technological advancements in the computer industry, represents an up-to-date challenge for I and C engineers in nuclear power plants throughout the world. In comparison with the time-proven, hard-wired I and C, the engineering must consider the novel characteristics of computer-based technology during the implementation, these are primarily constituted by higher performance and the utilisation of software. On one hand, this allows for implementing more complex I and C functions and integrating several I and C functions on to single components, although on the other hand, the minimisation of the CCF probability is of high priority to the engineering. Furthermore, the engineering must take the implementation of the deterministic safety concept for the I and C design into consideration. This includes engineering the redundancy, diversity, physical separation, and independence design features, and is complemented by the analysis of the I and C design with respect to the superposition of pre-defined event sequences and postulated failure combinations, so as to secure the safe operation of the nuclear power plant. The focus of this thesis is on the basic principles of engineering, i.e. description languages and methods, which the engineering relies on for a highly qualitative and efficient computer-based I and C implementation. The analysis of the deterministic safety concept and computer-based I and C characteristics yields the relevant technical requirements for the engineering, these are combined with the general structuring principles of standard IEC 81346 and the extended description language evaluation criteria, which are based on the guideline VDI/VDE-3681, resulting in target criteria for evaluating description languages. The analysis and comparison of existing description languages reveals that no description language satisfactorily fulfils all target criteria, which is constituted in the

Hardware description languages

Science.gov (United States)

Tucker, Jerry H.

1994-01-01

Hardware description languages are special purpose programming languages. They are primarily used to specify the behavior of digital systems and are rapidly replacing traditional digital system design techniques. This is because they allow the designer to concentrate on how the system should operate rather than on implementation details. Hardware description languages allow a digital system to be described with a wide range of abstraction, and they support top down design techniques. A key feature of any hardware description language environment is its ability to simulate the modeled system. The two most important hardware description languages are Verilog and VHDL. Verilog has been the dominant language for the design of application specific integrated circuits (ASIC's). However, VHDL is rapidly gaining in popularity.

System design description for master equipment list, phase I

International Nuclear Information System (INIS)

Sandoval, J.D.

1997-01-01

This System Design Description (SDD) is for the Master Equipment List Phase I (MEL). It has been prepared following the WI-IC-CM-3-10, ''Software Practices,'' (Ref. 6). This SDD describes the internal design for implementation of the MEL Phase I

WRAP Module 1 data management system (DMS) software design description (SDD)

Energy Technology Data Exchange (ETDEWEB)

Talmage, P.A.

1995-03-17

The Waste Receiving and Processing (WRAP) Module 1 Data Management System (DMS) System Design Description (SDD) describes the logical and physical architecture of the system. The WRAP 1 DMS SDD formally partitions the elements of the system described in the WRAP 1 DMS Software requirements specification into design objects and describes the key properties and relationships among the design objects and interfaces with external systems such as the WRAP Plant Control System (PCS). The WRAP 1 DMS SDD can be thought of as a detailed blueprint for implementation activities. The design descriptions contained within this document will describe, in detail, the software products that will be developed to assist the Project W-026, Waste Receiving and Processing Module 1, in their management functions. The WRAP 1 DMS is required to collect, store, and report data related to certification, tracking, packaging, repackaging, processing, and shipment of waste processed or stored at the WRAP 1 facility.

WRAP Module 1 data management system (DMS) software design description (SDD)

International Nuclear Information System (INIS)

Talmage, P.A.

1995-01-01

The Waste Receiving and Processing (WRAP) Module 1 Data Management System (DMS) System Design Description (SDD) describes the logical and physical architecture of the system. The WRAP 1 DMS SDD formally partitions the elements of the system described in the WRAP 1 DMS Software requirements specification into design objects and describes the key properties and relationships among the design objects and interfaces with external systems such as the WRAP Plant Control System (PCS). The WRAP 1 DMS SDD can be thought of as a detailed blueprint for implementation activities. The design descriptions contained within this document will describe, in detail, the software products that will be developed to assist the Project W-026, Waste Receiving and Processing Module 1, in their management functions. The WRAP 1 DMS is required to collect, store, and report data related to certification, tracking, packaging, repackaging, processing, and shipment of waste processed or stored at the WRAP 1 facility

Model and information abstraction for description-driven systems

International Nuclear Information System (INIS)

Estrella, F.; McClatchey, R.; Kovacs, Z.; Goff, J.-M.L.

2001-01-01

A crucial factor in the creation of adaptable systems dealing with changing requirements is the suitability of the underlying technology in allowing the evolution of the system. A reflective system utilizes an open architecture where implicit system aspects are reified to become explicit first-class (meta-data) objects. These implicit system aspects are often fundamental structures which are inaccessible and immutable, and their reification as meta-data objects can serve as the basis for changes and extensions to the system, making it self-describing. To address the evolvability issue, the author proposes a reflective architecture based on two orthogonal abstractions-model abstraction and information abstraction. In this architecture the modeling abstractions allow for the separation of the description meta-data from the system aspects they represent so that they can be managed and versioned independently, asynchronously and explicitly

A Petri Net Definition of a System Description Language

DEFF Research Database (Denmark)

Jensen, Kurt; Kyng, Morten; Madsen, Ole Lehrmann

1979-01-01

This paper introduces a language for the description of systems with concurrency, and presents a formal definition of its semantics. The language is based on Delta and the semantic model is an extension of Petri nets with a data part and with expressions attached to transitions and to places....

Observing Participating Observation—A Re-description Based on Systems Theory

Directory of Open Access Journals (Sweden)

Tina Bering Keiding

2010-09-01

Full Text Available Current methodology concerning participating observation in general leaves the act of observation unobserved. Approaching participating observation from systems theory offers fundamental new insights into the topic. Observation is always participation. There is no way to escape becoming a participant and, as such, co-producer of the observed phenomenon. There is no such thing as a neutral or objective description. As observation deals with differences and process meaning, all descriptions are re-constructions and interpretations of the observed. Hence, the idea of neutral descriptions as well as the idea of the naïve observer becomes a void. Not recognizing and observing oneself as observer and co-producer of empirical data simply leaves the process of observation as the major unobserved absorber of contingency in data production based on participating observation. URN: urn:nbn:de:0114-fqs1003119

Failure of single electron descriptions of molecular orbital collision processes

International Nuclear Information System (INIS)

Elston, S.B.

1978-01-01

Inner-shell excitation occurring in low and moderate (keV range) energy collisions between light atomic and ionic systems is frequently describable in terms of molecular promotion mechanisms, which were extensively explored both theoretically and experimentally. The bulk of such studies have concentrated on processes understandable through the use of single- and independent-electron models. Nonetheless, it is possible to find cases of inner-shell excitation in relatively simple collision systems which involve nearly simultaneous multiple-electron transitions and transitions induced by inherently two-electron interactions. Evidence for these many- and nonindependent-electron phenomena in inner-shell excitation processes and the importance of considering such effects in the interpretation of collisionally induced excitation spectra is discussed. 13 references

Computer systems for annotation of single molecule fragments

Science.gov (United States)

Schwartz, David Charles; Severin, Jessica

2016-07-19

There are provided computer systems for visualizing and annotating single molecule images. Annotation systems in accordance with this disclosure allow a user to mark and annotate single molecules of interest and their restriction enzyme cut sites thereby determining the restriction fragments of single nucleic acid molecules. The markings and annotations may be automatically generated by the system in certain embodiments and they may be overlaid translucently onto the single molecule images. An image caching system may be implemented in the computer annotation systems to reduce image processing time. The annotation systems include one or more connectors connecting to one or more databases capable of storing single molecule data as well as other biomedical data. Such diverse array of data can be retrieved and used to validate the markings and annotations. The annotation systems may be implemented and deployed over a computer network. They may be ergonomically optimized to facilitate user interactions.

US Department of Energy, Richland Operations Office Integrated Safety Management System Program Description

International Nuclear Information System (INIS)

SHOOP, D.S.

2000-01-01

The purpose of this Integrated Safety Management System (ISMS) Program Description (PD) is to describe the U.S. Department of Energy (DOE), Richland Operations Office (RL) ISMS as implemented through the RL Integrated Management System (RIMS). This PD does not impose additional requirements but rather provides an overview describing how various parts of the ISMS fit together. Specific requirements for each of the core functions and guiding principles are established in other implementing processes, procedures, and program descriptions that comprise RIMS. RL is organized to conduct work through operating contracts; therefore, it is extremely difficult to provide an adequate ISMS description that only addresses RL functions. Of necessity, this PD contains some information on contractor processes and procedures which then require RL approval or oversight

On the description of classical Einstein relativistic two-particle systems

International Nuclear Information System (INIS)

Aaberge, T.

1978-01-01

The author starts by considering the system of one free particle, and gives a sufficiently general description of this system to include the center of mass of systems of several particles. He then passes to the system of two particles. The coordinates separating the center of mass and the internal system are defined and the dynamics discussed. Finally the author outlines the construction of a more restrictive two-particle theory, and studies some consequences of the definition of a particle in an external field as a two-particle system in the limit where the mass of one of the particles becomes infinite. (Auth.)

Solar project description for Zien Mechanical Contractors-I single family residence, Milwaukee, Wisconsin

Science.gov (United States)

Beers, D.

1980-02-01

The Zien Mechanical site is a single family residence located in Milwaukee, Wisconsin. The home has two separate solar energy systems: an air system for space heating and cooling; a liquid system to preheat the potable hot water. The space heating and cooling system design and operation modes are described. The space heating system is designed to apply approximately 44 percent of the space heating requirements for the 1388 square foot residence. Engineering drawings are provided and the performance evaluation instrumentation is described.

40 CFR 90.421 - Dilute gaseous exhaust sampling and analytical system description.

Science.gov (United States)

2010-07-01

... gas mixture temperature, measured at a point immediately ahead of the critical flow venturi, must be... analytical system description. (a) General. The exhaust gas sampling system described in this section is... requirements are as follows: (1) This sampling system requires the use of a Positive Displacement Pump—Constant...

Expert system for accelerator single-freedom nonlinear components

International Nuclear Information System (INIS)

Wang Sheng; Xie Xi; Liu Chunliang

1995-01-01

An expert system by Arity Prolog is developed for accelerator single-freedom nonlinear components. It automatically yields any order approximate analytical solutions for various accelerator single-freedom nonlinear components. As an example, the eighth order approximate analytical solution is derived by this expert system for a general accelerator single-freedom nonlinear component, showing that the design of the expert system is successful

FURNACE; a toroidal geometry neutronic program system method description and users manual

International Nuclear Information System (INIS)

Verschuur, K.A.

1984-12-01

The FURNACE program system performs neutronic and photonic calculations in 3D toroidal geometry for application to fusion reactors. The geometry description is quite general, allowing any torus cross section and any neutron source density distribution for the plasma, as well as simple parametric representations of circular, elliptic and D-shaped tori and plasmas. The numerical method is based on an approximate transport model that produces results with sufficient accuracy for reactor-design purposes, at acceptable calculational costs. A short description is given of the numerical method, and a user manual for the programs of the system: FURNACE, ANISN-PT, LIBRA, TAPEMA and DRAWER is presented

Description of an open quantum mechanical system

International Nuclear Information System (INIS)

Rotter, I.; Forschungszentrum Rossendorf e.V.

1994-05-01

A model for the description of an open quantum mechanical many-particle system is formulated. It starts from the shell model and treats the continuous states by a coupled channels method. The mixing of the discrete shell model states via the continuum of decay channels results in the genuine decaying states of the system. These states are eigenstates of a non-Hermitean Hamilton operator the eigenvalues of which give both the energies and the widths of the states. All correlations between two particles which are caused by the two-particle residual interaction, are taken into account including those via the continuum. In the formalism describing the open quantum mechanical system, the coupling between the system and its environment appears nonlinearly. If the resonance states start to overlap, a redistribution of the spectroscopic values ('trapping effect') takes place. As a result, the complexity of the system is reduced at high level density, structures in space and time are formed. This redistribution describes, on the one hand, the transition from the well-known nuclear properties at low level density to those at high level density and fits, on the other hand, into the concept of selforganization. (orig.)

Deep hierarchical attention network for video description

Science.gov (United States)

Li, Shuohao; Tang, Min; Zhang, Jun

2018-03-01

Pairing video to natural language description remains a challenge in computer vision and machine translation. Inspired by image description, which uses an encoder-decoder model for reducing visual scene into a single sentence, we propose a deep hierarchical attention network for video description. The proposed model uses convolutional neural network (CNN) and bidirectional LSTM network as encoders while a hierarchical attention network is used as the decoder. Compared to encoder-decoder models used in video description, the bidirectional LSTM network can capture the temporal structure among video frames. Moreover, the hierarchical attention network has an advantage over single-layer attention network on global context modeling. To make a fair comparison with other methods, we evaluate the proposed architecture with different types of CNN structures and decoders. Experimental results on the standard datasets show that our model has a more superior performance than the state-of-the-art techniques.

Cold Vacuum Drying (CVD) Facility Vacuum Purge System Chilled Water System Design Description. System 47-4

International Nuclear Information System (INIS)

IRWIN, J.J.

2000-01-01

This system design description (SDD) addresses the Vacuum Purge System Chilled Water (VPSCHW) system. The discussion that follows is limited to the VPSCHW system and its interfaces with associated systems. The reader's attention is directed to Drawings H-1-82162, Cold Vacuum Drying Facility Process Equipment Skid PandID Vacuum System, and H-1-82224, Cold Vacuum Drying Facility Mechanical Utilities Process Chilled Water PandID. Figure 1-1 shows the location and equipment arrangement for the VPSCHW system. The VPSCHW system provides chilled water to the Vacuum Purge System (VPS). The chilled water provides the ability to condense water from the multi-canister overpack (MCO) outlet gases during the MCO vacuum and purge cycles. By condensing water from the MCO purge gas, the VPS can assist in drying the contents of the MCO

System design description for the SY-101 hydrogen mitigation test project data acquisition and control system (DACS-1)

International Nuclear Information System (INIS)

Ermi, A.M.

1998-01-01

There is no new activity or procedure associated with the updating of this reference document. The updating of this system design description maintains an agreed upon documentation program initiated within the test program and carried into operations at time of turnover to maintain configuration control as outlined by design authority practicing guidelines. Any changes made to controlled components in the field will be updated after the time of implementation to support the engineers and operators understand, maintain, train to and operate the system. There are no new credible failure modes associated with the updating of information in a support description document. The failure analysis of each change was reviewed at the time of implementation of the Systems Change Request for all the processes changed. This document simply provides a history of implementation and current system status. The incorporation of the two documents, Computer Systems Design Description (HNF-SD-WMCSDD-008) and the Input/Output Channel List (HNF-SD-WM-EL-001), as appendices allow for fewer errors in changes. Because the documents are all together, they will be approved as one document, not three separate entities which could be updated at different times, creating a situation which does not accurately depict field conditions

KALIMER fuel system preliminary design description

International Nuclear Information System (INIS)

Hwang, Woan; Lee, B.O.; Nam, C.; Paek, S.K.

1998-10-01

This document provides general design concepts, design basis, preliminary design specification and design technologies which are needed for designing the fuel/non-fuel rods and assembly ducts of the KALIMER fuel system. The core of LMFBR consists of driver fuel assembly, blanket assembly, reflector assembly, shielding assembly, control assembly and GEM (Gas Expansion Module) as well as USS, dummy assembly, detector assembly. These core components must be designed to withstand the high temperature, high flux for a long irradiation exposure time. Due to the high temperature and high flux, irradiation creep and swelling as well as thermal-mechanical deformation are occurred at the fuel/non-fuel system and cause the deformations of materials and the geometric deflections at fuel/non-fuel rods, assembly ducts and components. In order to overcome these intricate phenomena through the engineering design, the design basis including theoretical analysis methodologies and design considerations, material characteristics of fuel system, and the specifications and drawings of fuel/non-fuel rods and assembly ducts, respectively, are presented. This document is preliminary design description which is produced in the conceptual design stage, and does not present the detailed and finalized design data which can be for the manufacturing. (author). 22 refs

Description of the control and safety systems of the RA reactor

International Nuclear Information System (INIS)

Popovic, B.; Pesic, M.

1962-01-01

This report contains detailed description and scheme of the control and safety system of the RA reactor. It consists of interconnected five systems: for automated regulation; compensation rods; safety rods; power density measurement device; period meter; automated D 2 O level meter in the core. Automated regulation system is divided into two parts: basic system for reactor operation regime at power from 10kW - 10 MW and precise regulation system for operation at set-up power level up to 10 kW which is used occasionally

Architecture Descriptions. A Contribution to Modeling of Production System Architecture

DEFF Research Database (Denmark)

Jepsen, Allan Dam; Hvam, Lars

a proper understanding of the architecture phenomenon and the ability to describe it in a manner that allow the architecture to be communicated to and handled by stakeholders throughout the company. Despite the existence of several design philosophies in production system design such as Lean, that focus...... a diverse set of stakeholder domains and tools in the production system life cycle. To support such activities, a contribution is made to the identification and referencing of production system elements within architecture descriptions as part of the reference architecture framework. The contribution...

Concept for a Satellite-Based Advanced Air Traffic Management System : Volume 4. Operational Description and Qualitative Assessment.

Science.gov (United States)

1974-02-01

The volume presents a description of how the Satellite-Based Advanced Air Traffic Management System (SAATMS) operates and a qualitative assessment of the system. The operational description includes the services, functions, and tasks performed by the...

LANL environmental restoration site ranking system: System description. Final report

International Nuclear Information System (INIS)

Merkhofer, L.; Kann, A.; Voth, M.

1992-01-01

The basic structure of the LANL Environmental Restoration (ER) Site Ranking System and its use are described in this document. A related document, Instructions for Generating Inputs for the LANL ER Site Ranking System, contains detailed descriptions of the methods by which necessary inputs for the system will be generated. LANL has long recognized the need to provide a consistent basis for comparing the risks and other adverse consequences associated with the various waste problems at the Lab. The LANL ER Site Ranking System is being developed to help address this need. The specific purpose of the system is to help improve, defend, and explain prioritization decisions at the Potential Release Site (PRS) and Operable Unit (OU) level. The precise relationship of the Site Ranking System to the planning and overall budget processes is yet to be determined, as the system is still evolving. Generally speaking, the Site Ranking System will be used as a decision aid. That is, the system will be used to aid in the planning and budgetary decision-making process. It will never be used alone to make decisions. Like all models, the system can provide only a partial and approximate accounting of the factors important to budget and planning decisions. Decision makers at LANL will have to consider factors outside of the formal system when making final choices. Some of these other factors are regulatory requirements, DOE policy, and public concern. The main value of the site ranking system, therefore, is not the precise numbers it generates, but rather the general insights it provides

LANL environmental restoration site ranking system: System description. Final report

Energy Technology Data Exchange (ETDEWEB)

Merkhofer, L.; Kann, A.; Voth, M. [Applied Decision Analysis, Inc., Menlo Park, CA (United States)

1992-10-13

The basic structure of the LANL Environmental Restoration (ER) Site Ranking System and its use are described in this document. A related document, Instructions for Generating Inputs for the LANL ER Site Ranking System, contains detailed descriptions of the methods by which necessary inputs for the system will be generated. LANL has long recognized the need to provide a consistent basis for comparing the risks and other adverse consequences associated with the various waste problems at the Lab. The LANL ER Site Ranking System is being developed to help address this need. The specific purpose of the system is to help improve, defend, and explain prioritization decisions at the Potential Release Site (PRS) and Operable Unit (OU) level. The precise relationship of the Site Ranking System to the planning and overall budget processes is yet to be determined, as the system is still evolving. Generally speaking, the Site Ranking System will be used as a decision aid. That is, the system will be used to aid in the planning and budgetary decision-making process. It will never be used alone to make decisions. Like all models, the system can provide only a partial and approximate accounting of the factors important to budget and planning decisions. Decision makers at LANL will have to consider factors outside of the formal system when making final choices. Some of these other factors are regulatory requirements, DOE policy, and public concern. The main value of the site ranking system, therefore, is not the precise numbers it generates, but rather the general insights it provides.

CIRCUIT IMPLEMENTATION OF VHDL-DESCRIPTIONS OF SYSTEMS OF PARTIAL BOOLEAN FUNCTIONS

Directory of Open Access Journals (Sweden)

P. N. Bibilo

2016-01-01

Full Text Available Method for description of incompletely specified (partial Boolean functions in VHDL is proposed. Examples of synthesized VHDL models of partial Boolean functions are presented; and the results of experiments on circuit implementation of VHDL descriptions of systems of partial functions. The realizability of original partial functions in logical circuits was verified by formal verification. The results of the experiments show that the preliminary minimization in DNF class and in the class of BDD representations for pseudo-random systems of completely specified functions does not improve practically (and in the case of BDD sometimes worsens the results of the subsequent synthesis in the basis of FPGA unlike the significant efficiency of these procedures for the synthesis of benchmark circuits taken from the practice of the design.

Using Self-Description to Handle Change in Systems, CMS-CR-2002-010

CERN Document Server

Estrella, F; Le Goff, J M; McClatchey, R; Murray, S

2002-01-01

In the web age systems must be flexible, reconfigurable and adaptable in addition to being quick to develop. As a consequence, designing systems to cater for change is becoming not only desirable but required by industry. Allowing systems to be self-describing or description-driven is one way to enable these characteristics. To address the issue of evolvability in designing self-describing systems, this paper proposes a pattern-based, object-oriented, description-driven architecture. The proposed architecture embodies four pillars - first, the adoption of a multi-layered meta-modeling architecture and reflective meta-level architecture, second, the identification of four data modeling relationships that must be made explicit such that they can be examined and modified dynamically, third, the identification of five design patterns which have emerged from practice and have proved essential in providing reusable building blocks for data management, and fourth, the encoding of the structural properties of the fiv...

Probabilistic endowment appraisal system based upon the formalization of geologic decisions. General description

International Nuclear Information System (INIS)

Harris, D.P.; Carrigan, F.J.

1980-04-01

The objectives of this study include the design of an appraisal system which has the following features: estimates uranium endowment, not resources; formalizes the geologist's geoscience and assists the geologist in the exercise of his geoscience; describes the probability distribution for uranium endowment; diminishes or at least does not contribute to psychometric biases; provides for anonymous exchange among multiple experts of tenets of geoscience, but not the exchange of endowment estimates; provides an endowment estimate based upon geoscience only; is not easily gamed or manipulated; and provides for a quick and easy review of geoscience and resource information. This report is reflective of its title, a general description. The appraisal system resulting from this research is complex in the detail of its design and use. However, the major concepts which are reflected by the system are simple. The purpose of this report is to establish clearly these major concepts and the manner in which the system applies these concepts. Many details, refinements, and caveats are purposefully suppressed in order to provide this general description. While this suppression is a loss to some readers, it is a benefit to a wider spectrum of readers. Those interested in the nuts and bolts of the system will also want to read the user's manual which accompanies this general description

YUCCA MOUNTAIN SITE DESCRIPTION

International Nuclear Information System (INIS)

Simmons, A.M.

2004-01-01

The ''Yucca Mountain Site Description'' summarizes, in a single document, the current state of knowledge and understanding of the natural system at Yucca Mountain. It describes the geology; geochemistry; past, present, and projected future climate; regional hydrologic system; and flow and transport within the unsaturated and saturated zones at the site. In addition, it discusses factors affecting radionuclide transport, the effect of thermal loading on the natural system, and tectonic hazards. The ''Yucca Mountain Site Description'' is broad in nature. It summarizes investigations carried out as part of the Yucca Mountain Project since 1988, but it also includes work done at the site in earlier years, as well as studies performed by others. The document has been prepared under the Office of Civilian Radioactive Waste Management quality assurance program for the Yucca Mountain Project. Yucca Mountain is located in Nye County in southern Nevada. The site lies in the north-central part of the Basin and Range physiographic province, within the northernmost subprovince commonly referred to as the Great Basin. The basin and range physiography reflects the extensional tectonic regime that has affected the region during the middle and late Cenozoic Era. Yucca Mountain was initially selected for characterization, in part, because of its thick unsaturated zone, its arid to semiarid climate, and the existence of a rock type that would support excavation of stable openings. In 1987, the United States Congress directed that Yucca Mountain be the only site characterized to evaluate its suitability for development of a geologic repository for high-level radioactive waste and spent nuclear fuel

Robotics/Automated Systems Task Analysis and Description of Required Job Competencies Report. Task Analysis and Description of Required Job Competencies of Robotics/Automated Systems Technicians.

Science.gov (United States)

Hull, Daniel M.; Lovett, James E.

This task analysis report for the Robotics/Automated Systems Technician (RAST) curriculum project first provides a RAST job description. It then discusses the task analysis, including the identification of tasks, the grouping of tasks according to major areas of specialty, and the comparison of the competencies to existing or new courses to…

Cold Vacuum Drying facility civil - structural system design description (SYS 06)

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying (CVD) Facility civil - structural system. This system consists of the facility structure, including the administrative and process areas. The system's primary purpose is to provide for a facility to house the CVD process and personnel and to provide a tertiary level of containment. The document provides a description of the facility and demonstrates how the design meets the various requirements imposed by the safety analysis report and the design requirements document

34 CFR 200.12 - Single State accountability system.

Science.gov (United States)

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Single State accountability system. 200.12 Section 200... Improving Basic Programs Operated by Local Educational Agencies State Accountability System § 200.12 Single State accountability system. (a)(1) Each State must demonstrate in its State plan that the State has...

Cold Vacuum Drying facility heating, ventilation, and Air Conditioning system design description

International Nuclear Information System (INIS)

SINGH, G.

2000-01-01

This System Design Description (SDD) addresses the HVAC system for the CVDF. The CVDF HVAC system consists of five subsystems: (1) Administration building HVAC system; (2) Process bay recirculation HVAC system; (3) Process bay local exhaust HVAC and process vent system; (4) Process general supply/exhaust HVAC system; and (5) Reference air system. The HVAC and reference air systems interface with the following systems: the fire protection control system, Monitoring and Control System (MCS), electrical power distribution system (including standby power), compressed air system, Chilled Water (CHW) system, drainage system, and other Cold Vacuum Drying (CVD) control systems not addressed in this SDD

Factors associated with anxiety and depression among type 2 diabetes outpatients in Malaysia: a descriptive cross-sectional single-centre study

OpenAIRE

Ganasegeran, Kurubaran; Renganathan, Pukunan; Manaf, Rizal Abdul; Al-Dubai, Sami Abdo Radman

2014-01-01

Objective To determine the prevalence and factors associated with anxiety and depression among type 2 diabetes outpatients in Malaysia. Design Descriptive, cross-sectional single-centre study with universal sampling of all patients with type 2 diabetes. Setting Endocrinology clinic of medical outpatient department in a Malaysian public hospital. Participants All 169 patients with type 2 diabetes (men, n=99; women, n=70) aged between 18 and 90 years who acquired follow-up treatment from the en...

Prism-based single-camera system for stereo display

Science.gov (United States)

Zhao, Yue; Cui, Xiaoyu; Wang, Zhiguo; Chen, Hongsheng; Fan, Heyu; Wu, Teresa

2016-06-01

This paper combines the prism and single camera and puts forward a method of stereo imaging with low cost. First of all, according to the principle of geometrical optics, we can deduce the relationship between the prism single-camera system and dual-camera system, and according to the principle of binocular vision we can deduce the relationship between binoculars and dual camera. Thus we can establish the relationship between the prism single-camera system and binoculars and get the positional relation of prism, camera, and object with the best effect of stereo display. Finally, using the active shutter stereo glasses of NVIDIA Company, we can realize the three-dimensional (3-D) display of the object. The experimental results show that the proposed approach can make use of the prism single-camera system to simulate the various observation manners of eyes. The stereo imaging system, which is designed by the method proposed by this paper, can restore the 3-D shape of the object being photographed factually.

Cold Vacuum Drying Instrument Air System Design Description (SYS 12)

Energy Technology Data Exchange (ETDEWEB)

SHAPLEY, B.J.; TRAN, Y.S.

2000-06-05

This system design description (SDD) addresses the instrument air (IA) system of the spent nuclear fuel (SNF). This IA system provides instrument quality air to the Cold Vacuum Drying (CVD) Facility. The IA system is a general service system that supports the operation of the heating, ventilation, and air conditioning (HVAC) system, the process equipment skids, and process instruments in the CVD Facility. The following discussion is limited to the compressor, dryer, piping, and valving that provide the IA as shown in Drawings H-1-82222, Cold Vacuum Drying Facility Mechanical Utilities Compressed & Instrument Air P&ID, and H-1.82161, Cold Vacuum Drying Facility Process Equipment Skid P&ID MCO/Cusk Interface. Figure 1-1 shows the physical location of the 1A system in the CVD Facility.

Thermally activated, single component epoxy systems

KAUST Repository

Unruh, David A.; Pastine, Stefan J.; Moreton, Jessica C.; Frechet, Jean

2011-01-01

A single component epoxy system in which the resin and hardener components found in many two-component epoxies are combined onto the same molecule is described. The single molecule precursor to the epoxy resin contains both multiple epoxide moieties and a diamine held latent by thermally degradable carbamate linkages. These bis-carbamate "single molecule epoxies" have an essentially infinite shelf life and access a significant range in curing temperatures related to the structure of the carbamate linkages used. © 2011 American Chemical Society.

Thermally activated, single component epoxy systems

KAUST Repository

Unruh, David A.

2011-08-23

A single component epoxy system in which the resin and hardener components found in many two-component epoxies are combined onto the same molecule is described. The single molecule precursor to the epoxy resin contains both multiple epoxide moieties and a diamine held latent by thermally degradable carbamate linkages. These bis-carbamate "single molecule epoxies" have an essentially infinite shelf life and access a significant range in curing temperatures related to the structure of the carbamate linkages used. © 2011 American Chemical Society.

Simulation model for wind energy storage systems. Volume III. Program descriptions. [SIMWEST CODE

Energy Technology Data Exchange (ETDEWEB)

Warren, A.W.; Edsinger, R.W.; Burroughs, J.D.

1977-08-01

The effort developed a comprehensive computer program for the modeling of wind energy/storage systems utilizing any combination of five types of storage (pumped hydro, battery, thermal, flywheel and pneumatic). An acronym for the program is SIMWEST (Simulation Model for Wind Energy Storage). The level of detail of SIMWEST is consistent with a role of evaluating the economic feasibility as well as the general performance of wind energy systems. The software package consists of two basic programs and a library of system, environmental, and load components. Volume III, the SIMWEST program description contains program descriptions, flow charts and program listings for the SIMWEST Model Generation Program, the Simulation program, the File Maintenance program and the Printer Plotter program. Volume III generally would not be required by SIMWEST user.

Technical description of the burn-up software system MOP

International Nuclear Information System (INIS)

Schutte, C.K.

1991-05-01

The burn-up software system MOP is a research tool primary intended to study the behaviour of fission products in any reactor composition. Input data are multi-group cross-sections and data concerning the nuclide chains. An option is available to calculate a fundamental mode neutron spectrum for the specified reactor composition. A separate program can test the consistency of the specified nuclide chains. Options are available to calculate time-dependent cross-sections of lumped fission products and to take account of the leakage of gaseous fission products from the reactor core. The system is written in FORTRAN77 for a CYBER computer, using the operating system NOS/BE. The report gives a detailed technical description of the applied algorithms and the flow and storage of data. Information is provided for adapting the system to other computer configurations. (author). 5 refs.; 11 figs

AHTR Refueling Systems and Process Description

Energy Technology Data Exchange (ETDEWEB)

Varma, V.K.; Holcomb, D.E.; Bradley, E.C.; Zaharia, N.M.; Cooper, E.J.

2012-07-15

The Advanced High-Temperature Reactor (AHTR) is a design concept for a central station-type [1500 MW(e)] Fluoride salt–cooled High-temperature Reactor (FHR) that is currently undergoing development by Oak Ridge National Laboratory for the US. Department of Energy, Office of Nuclear Energy’s Advanced Reactor Concepts program. FHRs, by definition, feature low-pressure liquid fluoride salt cooling, coated-particle fuel, a high-temperature power cycle, and fully passive decay heat rejection. The overall goal of the AHTR development program is to demonstrate the technical feasibility of FHRs as low-cost, large-size power producers while maintaining full passive safety. The AHTR is approaching a preconceptual level of maturity. An initial integrated layout of its major systems, structures, and components (SSCs), and an initial, high-level sequence of operations necessary for constructing and operating the plant is nearing completion. An overview of the current status of the AHTR concept has been recently published [1], and a report providing a more detailed overview of the AHTR structures and mechanical systems is currently in preparation. This report documents the refueling components and processes envisioned at this early development phase. The report is limited to the refueling aspects of the AHTR and does not include overall reactor or power plant design information. The report, however, does include a description of the materials envisioned for the various components and the instrumentation necessary to control the refueling process. The report begins with an overview of the refueling strategy. Next a mechanical description of the AHTR fuel assemblies and core is provided. The reactor vessel upper assemblies are then described. Following this the refueling path structures and the refueling mechanisms and components are described. The sequence of operations necessary to fuel and defuel the reactor is then discussed. The report concludes with a discussion of the

AHTR Refueling Systems and Process Description

Energy Technology Data Exchange (ETDEWEB)

Varma, Venugopal Koikal [ORNL; Holcomb, David Eugene [ORNL; Bradley, Eric Craig [ORNL; Zaharia, Nathaniel M [ORNL; Cooper, Eliott J [ORNL

2012-07-01

The Advanced High-Temperature Reactor (AHTR) is a design concept for a central station-type [1500 MW(e)] Fluoride salt-cooled High-temperature Reactor (FHR) that is currently undergoing development by Oak Ridge National Laboratory for the US. Department of Energy, Office of Nuclear Energy's Advanced Reactor Concepts program. FHRs, by definition, feature low-pressure liquid fluoride salt cooling, coated-particle fuel, a high-temperature power cycle, and fully passive decay heat rejection. The overall goal of the AHTR development program is to demonstrate the technical feasibility of FHRs as low-cost, large-size power producers while maintaining full passive safety. The AHTR is approaching a preconceptual level of maturity. An initial integrated layout of its major systems, structures, and components (SSCs), and an initial, high-level sequence of operations necessary for constructing and operating the plant is nearing completion. An overview of the current status of the AHTR concept has been recently published and a report providing a more detailed overview of the AHTR structures and mechanical systems is currently in preparation. This report documents the refueling components and processes envisioned at this early development phase. The report is limited to the refueling aspects of the AHTR and does not include overall reactor or power plant design information. The report, however, does include a description of the materials envisioned for the various components and the instrumentation necessary to control the refueling process. The report begins with an overview of the refueling strategy. Next a mechanical description of the AHTR fuel assemblies and core is provided. The reactor vessel upper assemblies are then described. Following this the refueling path structures and the refueling mechanisms and components are described. The sequence of operations necessary to fuel and defuel the reactor is then discussed. The report concludes with a discussion of the

Organization model and formalized description of nuclear enterprise information system

International Nuclear Information System (INIS)

Yuan Feng; Song Yafeng; Li Xudong

2012-01-01

Organization model is one of the most important models of Nuclear Enterprise Information System (NEIS). Scientific and reasonable organization model is the prerequisite that NEIS has robustness and extendibility, and is also the foundation of the integration of heterogeneous system. Firstly, the paper describes the conceptual model of the NEIS on ontology chart, which provides a consistent semantic framework of organization. Then it discusses the relations between the concepts in detail. Finally, it gives the formalized description of the organization model of NEIS based on six-tuple array. (authors)

Automated imaging system for single molecules

Science.gov (United States)

Schwartz, David Charles; Runnheim, Rodney; Forrest, Daniel

2012-09-18

There is provided a high throughput automated single molecule image collection and processing system that requires minimal initial user input. The unique features embodied in the present disclosure allow automated collection and initial processing of optical images of single molecules and their assemblies. Correct focus may be automatically maintained while images are collected. Uneven illumination in fluorescence microscopy is accounted for, and an overall robust imaging operation is provided yielding individual images prepared for further processing in external systems. Embodiments described herein are useful in studies of any macromolecules such as DNA, RNA, peptides and proteins. The automated image collection and processing system and method of same may be implemented and deployed over a computer network, and may be ergonomically optimized to facilitate user interaction.

Adjustable Nyquist-rate System for Single-Bit Sigma-Delta ADC with Alternative FIR Architecture

Science.gov (United States)

Frick, Vincent; Dadouche, Foudil; Berviller, Hervé

2016-09-01

This paper presents a new smart and compact system dedicated to control the output sampling frequency of an analogue-to-digital converters (ADC) based on single-bit sigma-delta (ΣΔ) modulator. This system dramatically improves the spectral analysis capabilities of power network analysers (power meters) by adjusting the ADC's sampling frequency to the input signal's fundamental frequency with a few parts per million accuracy. The trade-off between straightforwardness and performance that motivated the choice of the ADC's architecture are preliminary discussed. It particularly comes along with design considerations of an ultra-steep direct-form FIR that is optimised in terms of size and operating speed. Thanks to compact standard VHDL language description, the architecture of the proposed system is particularly suitable for application-specific integrated circuit (ASIC) implementation-oriented low-power and low-cost power meter applications. Field programmable gate array (FPGA) prototyping and experimental results validate the adjustable sampling frequency concept. They also show that the system can perform better in terms of implementation and power capabilities compared to dedicated IP resources.

Plant Systems Biology at the Single-Cell Level.

Science.gov (United States)

Libault, Marc; Pingault, Lise; Zogli, Prince; Schiefelbein, John

2017-11-01

Our understanding of plant biology is increasingly being built upon studies using 'omics and system biology approaches performed at the level of the entire plant, organ, or tissue. Although these approaches open new avenues to better understand plant biology, they suffer from the cellular complexity of the analyzed sample. Recent methodological advances now allow plant scientists to overcome this limitation and enable biological analyses of single-cells or single-cell-types. Coupled with the development of bioinformatics and functional genomics resources, these studies provide opportunities for high-resolution systems analyses of plant phenomena. In this review, we describe the recent advances, current challenges, and future directions in exploring the biology of single-cells and single-cell-types to enhance our understanding of plant biology as a system. Copyright © 2017 Elsevier Ltd. All rights reserved.

Spent nuclear fuel project cold vacuum drying facility vacuum and purge system design description

Energy Technology Data Exchange (ETDEWEB)

IRWIN, J.J.

1998-11-30

This document provides the System Design Description (SDD) for the Cold Vacuum Drying Facility (CVDF) Vacuum and Purge System (VPS) . The SDD was developed in conjunction with HNF-SD-SNF-SAR-O02, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998), The HNF-SD-SNF-DRD-002, 1998, Cold Vacuum Drying Facility Design Requirements, and the CVDF Design Summary Report. The SDD contains general descriptions of the VPS equipment, the system functions, requirements and interfaces. The SDD provides references for design and fabrication details, operation sequences and maintenance. This SDD has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved.

Spent nuclear fuel project cold vacuum drying facility process water conditioning system design description

International Nuclear Information System (INIS)

IRWIN, J.J.

1998-01-01

This document provides the System Design Description (SDD) for the Cold Vacuum Drying Facility (CVDF) Process Water Conditioning (PWC) System. The SDD was developed in conjunction with HNF-SD-SNF-SAR-002, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998), the HNF-SD-SNF-DRD-O02, 1998, Cold Vacuum Drying Facility Design Requirements, and the CVDF Design Summary Report. The SDD contains general descriptions of the PWC equipment, the system functions, requirements and interfaces. The SDD provides references for design and fabrication details, operation sequences and maintenance. This SDD has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved

Spent nuclear fuel project cold vacuum drying facility vacuum and purge system design description

International Nuclear Information System (INIS)

IRWIN, J.J.

1998-01-01

This document provides the System Design Description (SDD) for the Cold Vacuum Drying Facility (CVDF) Vacuum and Purge System (VPS) . The SDD was developed in conjunction with HNF-SD-SNF-SAR-O02, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998), The HNF-SD-SNF-DRD-002, 1998, Cold Vacuum Drying Facility Design Requirements, and the CVDF Design Summary Report. The SDD contains general descriptions of the VPS equipment, the system functions, requirements and interfaces. The SDD provides references for design and fabrication details, operation sequences and maintenance. This SDD has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved

YUCCA MOUNTAIN SITE DESCRIPTION

Energy Technology Data Exchange (ETDEWEB)

A.M. Simmons

2004-04-16

The ''Yucca Mountain Site Description'' summarizes, in a single document, the current state of knowledge and understanding of the natural system at Yucca Mountain. It describes the geology; geochemistry; past, present, and projected future climate; regional hydrologic system; and flow and transport within the unsaturated and saturated zones at the site. In addition, it discusses factors affecting radionuclide transport, the effect of thermal loading on the natural system, and tectonic hazards. The ''Yucca Mountain Site Description'' is broad in nature. It summarizes investigations carried out as part of the Yucca Mountain Project since 1988, but it also includes work done at the site in earlier years, as well as studies performed by others. The document has been prepared under the Office of Civilian Radioactive Waste Management quality assurance program for the Yucca Mountain Project. Yucca Mountain is located in Nye County in southern Nevada. The site lies in the north-central part of the Basin and Range physiographic province, within the northernmost subprovince commonly referred to as the Great Basin. The basin and range physiography reflects the extensional tectonic regime that has affected the region during the middle and late Cenozoic Era. Yucca Mountain was initially selected for characterization, in part, because of its thick unsaturated zone, its arid to semiarid climate, and the existence of a rock type that would support excavation of stable openings. In 1987, the United States Congress directed that Yucca Mountain be the only site characterized to evaluate its suitability for development of a geologic repository for high-level radioactive waste and spent nuclear fuel.

The AutoBayes Program Synthesis System: System Description

Science.gov (United States)

Fischer, Bernd; Pressburger, Thomas; Rosu, Grigore; Schumann, Johann; Norvog, Peter (Technical Monitor)

2001-01-01

AUTOBAYES is a fully automatic program synthesis system for the statistical data analysis domain. Its input is a concise description of a data analysis problem in the form of a statistical model; its output is optimized and fully documented C/C++ code which can be linked dynamically into the Matlab and Octave environments. AUTOBAYES synthesizes code by a schema-guided deductive process. Schemas (i.e., code templates with associated semantic constraints) are applied to the original problem and recursively to emerging subproblems. AUTOBAYES complements this approach by symbolic computation to derive closed-form solutions whenever possible. In this paper, we concentrate on the interaction between the symbolic computations and the deductive synthesis process. A statistical model specifies for each problem variable (i.e., data or parameter) its properties and dependencies in the form of a probability distribution, A typical data analysis task is to estimate the best possible parameter values from the given observations or measurements. The following example models normal-distributed data but takes prior information (e.g., from previous experiments) on the data's mean value and variance into account.

Information resource description creating and managing metadata

CERN Document Server

Hider, Philip

2012-01-01

An overview of the field of information organization that examines resource description as both a product and process of the contemporary digital environment.This timely book employs the unifying mechanism of the semantic web and the resource description framework to integrate the various traditions and practices of information and knowledge organization. Uniquely, it covers both the domain-specific traditions and practices and the practices of the ?metadata movement' through a single lens ? that of resource description in the broadest, semantic web sense.This approach more readily accommodate

41 CFR 101-29.102 - Use of metric system of measurement in Federal product descriptions.

Science.gov (United States)

2010-07-01

... PROCUREMENT 29-FEDERAL PRODUCT DESCRIPTIONS 29.1-General § 101-29.102 Use of metric system of measurement in... measurement in Federal product descriptions. 101-29.102 Section 101-29.102 Public Contracts and Property... Federal agencies to: (a) Maintain close liaison with other Federal agencies, State and local governments...

A brief description of Polanco`s hybrid system

Energy Technology Data Exchange (ETDEWEB)

Nunes, Ventura [Instituto de Ingenieria Electrica, Universidad de la Republica, Montevideo (Uruguay)

1997-12-31

Since 1995, a hybrid system wind - PV is in service in Polanco, Uruguay. A brief description of this system and the criteria employed in its design are outlined. The experience obtained during two years operation are described from the points of view of the equipment reliability and of the electrical service provided. Future prospects of this kind of installations in Uruguay as part of the rural electrification policy are presented. [Espanol] Desde 1995 esta en servicio en Polanco, Uruguay un sistema hibrido viento-fotovoltaico. Aqui se describe brevemente este sistema y el criterio empleado en su diseno. Se describe la experiencia obtenida durante dos anos de operacion desde el punto de vista de confiabilidad de los equipos y del servicio electrico proporcionado. Se presentan prospectos futuros de esta clase de instalaciones en Uruguay, como parte de la politica de electrificacion rural.

A brief description of Polanco`s hybrid system

Energy Technology Data Exchange (ETDEWEB)

Nunes, Ventura [Instituto de Ingenieria Electrica, Universidad de la Republica, Montevideo (Uruguay)

1998-12-31

Since 1995, a hybrid system wind - PV is in service in Polanco, Uruguay. A brief description of this system and the criteria employed in its design are outlined. The experience obtained during two years operation are described from the points of view of the equipment reliability and of the electrical service provided. Future prospects of this kind of installations in Uruguay as part of the rural electrification policy are presented. [Espanol] Desde 1995 esta en servicio en Polanco, Uruguay un sistema hibrido viento-fotovoltaico. Aqui se describe brevemente este sistema y el criterio empleado en su diseno. Se describe la experiencia obtenida durante dos anos de operacion desde el punto de vista de confiabilidad de los equipos y del servicio electrico proporcionado. Se presentan prospectos futuros de esta clase de instalaciones en Uruguay, como parte de la politica de electrificacion rural.

Total robotic radical rectal resection with da Vinci Xi system: single docking, single phase technique.

Science.gov (United States)

Tamhankar, Anup Sunil; Jatal, Sudhir; Saklani, Avanish

2016-12-01

This study aims to assess the advantages of Da Vinci Xi system in rectal cancer surgery. It also assesses the initial oncological outcomes after rectal resection with this system from a tertiary cancer center in India. Robotic rectal surgery has distinct advantages over laparoscopy. Total robotic resection is increasing following the evolution of hybrid technology. The latest Da Vinci Xi system (Intuitive Surgical, Sunnyvale, USA) is enabled with newer features to make total robotic resection possible with single docking and single phase. Thirty-six patients underwent total robotic resection in a single phase and single docking. We used newer port positions in a straight line. Median distance from the anal verge was 4.5 cm. Median robotic docking time and robotic procedure time were 9 and 280 min, respectively. Median blood loss was 100 mL. One patient needed conversion to an open approach due to advanced disease. Circumferential resection margin and longitudinal resection margins were uninvolved in all other patients. Median lymph node yield was 10. Median post-operative stay was 7 days. There were no intra-operative adverse events. The latest Da Vinci Xi system has made total robotic rectal surgery feasible in single docking and single phase. With the new system, four arm total robotic rectal surgery may replace the hybrid technique of laparoscopic and robotic surgery for rectal malignancies. The learning curve for the new system appears to be shorter than anticipated. Early perioperative and oncological outcomes of total robotic rectal surgery with the new system are promising. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Analytic descriptions of stochastic bistable systems under force ramp.

Science.gov (United States)

Friddle, Raymond W

2016-05-01

Solving the two-state master equation with time-dependent rates, the ubiquitous driven bistable system, is a long-standing problem that does not permit a complete solution for all driving rates. Here we show an accurate approximation to this problem by considering the system in the control parameter regime. The results are immediately applicable to a diverse range of bistable systems including single-molecule mechanics.

Employing Picture Description to Assess the Students' Descriptive Paragraph Writing

Directory of Open Access Journals (Sweden)

Ida Ayu Mega Cahyani

2018-03-01

Full Text Available Writing is considered as an important skill in learning process which is needed to be mastered by the students. However, in teaching learning process at schools or universities, the assessment of writing skill is not becoming the focus of learning process and the assessment is administered inappropriately. In this present study, the researcher undertook the study which dealt with assessing descriptive paragraph writing ability of the students through picture description by employing an ex post facto as the research design. The present study was intended to answer the research problem dealing with the extent of the students’ achievement of descriptive paragraph writing ability which is assessed through picture description. The samples under the study were 40 students determined by means of random sampling technique with lottery system. The data were collected through administering picture description as the research instrument. The obtained data were analyzed by using norm-reference measure of five standard values. The results of the data analysis showed that there were 67.50% samples of the study were successful in writing descriptive paragraph, while there were 32.50% samples were unsuccessful in writing descriptive paragraph which was assessed by administering picture description test

W-314, waste transfer alternative piping system description

International Nuclear Information System (INIS)

Papp, I.G.

1998-01-01

It is proposed that the reliability, operability, and flexibility of the Retrieval Transfer System be substantially upgraded by replacing the planned single in-farm pipeline from the AN-AY-AZ-(SY) Tank Farm Complex to the AP Farm with three parallel pipelines outside the tank farms. The proposed system provides simplified and redundant routes for the various transfer missions, and prevents the risk of transfer gridlock when the privatization effort swings into full operation

W-314, waste transfer alternative piping system description

Energy Technology Data Exchange (ETDEWEB)

Papp, I.G.

1998-04-30

It is proposed that the reliability, operability, and flexibility of the Retrieval Transfer System be substantially upgraded by replacing the planned single in-farm pipeline from the AN-AY-AZ-(SY) Tank Farm Complex to the AP Farm with three parallel pipelines outside the tank farms. The proposed system provides simplified and redundant routes for the various transfer missions, and prevents the risk of transfer gridlock when the privatization effort swings into full operation.

Feasibility of a responsive, hybrid propulsion augmented, Vertical-Takeoff-and-Landing, Single-Stage-to-Orbit launch system

Science.gov (United States)

Pelaccio, Dennis G.

1996-03-01

A novel, reusable, Vertical-Takeoff-and-Landing, Single-Stage-to-Orbit (VTOL/SSTO) launch system concept, named HYP-SSTO, is presented in this paper. This launch vehicle system concept uses a highly coupled, main high performance liquid oxygen/liquid hydrogen (LOX/LH2) propulsion system, that is used only for launch, with a hybrid auxiliary propulsion system which is used during final orbit insertion, major orbit maneuvering, and landing propulsive burn phases of flight. By using a hybrid propulsion system for major orbit maneuver burns and landing, this launch system concept has many advantages over conventional VTOL/SSTO concepts that use LOX/LH2 propulsion system(s) burns for all phases of flight. Because hybrid propulsion systems are relatively simple and inert by their nature, this concept has the potential to support short turnaround times between launches, be economical to develop, and be competitive in terms of overall system life-cycle cost. This paper provides a technical description of the novel, reusable HYP-SSTO launch system concept. Launch capability performance, as well as major design and operational system attributes, are identified and discussed.

Shippingport Spent Fuel Canister System Description

International Nuclear Information System (INIS)

JOHNSON, D.M.

2000-01-01

In 1978 and 1979, a total of 72 blanket fuel assemblies (BFAs), irradiated during the operating cycles of the Shippingport Atomic Power Station's Pressurized Water Reactor (PWR) Core 2 from April 1965 to February 1974, were transferred to the Hanford Site and stored in underwater storage racks in Cell 2R at the 221-T Canyon (T-Plant). The initial objective was to recover the produced plutonium in the BFAs, but this never occurred and the fuel assemblies have remained within the water storage pool to the present time. The Shippingport Spent Fuel Canister (SSFC) is a confinement system that provides safe transport functions (in conjunction with the TN-WHC cask) and storage for the BFAs at the Canister Storage Building (CSB). The current plan is for these BFAs to be retrieved from wet storage and loaded into SSFCs for dry storage. The sealed SSFCs containing BFAs will be vacuum dried, internally backfilled with helium, and leak tested to provide suitable confinement for the BFAs during transport and storage. Following completion of the drying and inerting process, the SSFCs are to be delivered to the CSB for closure welding and long-term interim storage. The CSB will provide safe handling and dry storage for the SSFCs containing the BFAs. The purpose of this document is to describe the SSFC system and interface equipment, including the technical basis for the system, design descriptions, and operations requirements. It is intended that this document will be periodically updated as more equipment design and performance specification information becomes available

Program computes single-point failures in critical system designs

Science.gov (United States)

Brown, W. R.

1967-01-01

Computer program analyzes the designs of critical systems that will either prove the design is free of single-point failures or detect each member of the population of single-point failures inherent in a system design. This program should find application in the checkout of redundant circuits and digital systems.

Linear systems optimal and robust control

CERN Document Server

Sinha, Alok

2007-01-01

Introduction Overview Contents of the Book State Space Description of a Linear System Transfer Function of a Single Input/Single Output (SISO) System State Space Realizations of a SISO System SISO Transfer Function from a State Space Realization Solution of State Space Equations Observability and Controllability of a SISO System Some Important Similarity Transformations Simultaneous Controllability and Observability Multiinput/Multioutput (MIMO) Systems State Space Realizations of a Transfer Function Matrix Controllability and Observability of a MIMO System Matrix-Fraction Description (MFD) MFD of a Transfer Function Matrix for the Minimal Order of a State Space Realization Controller Form Realization from a Right MFD Poles and Zeros of a MIMO Transfer Function Matrix Stability Analysis State Feedback Control and Optimization State Variable Feedback for a Single Input System Computation of State Feedback Gain Matrix for a Multiinput System State Feedback Gain Matrix for a Multi...

Formation of a dinuclear copper(II) complex through the cleavage of Cdescription='Single-Bond' name='Single-Bond' value='Single-Bond'/>N bond of 1-benzoyl-3-(pyridin-2-yl)-1H-pyrazole

Energy Technology Data Exchange (ETDEWEB)

Shardin, Rosidah; Pui, Law Kung; Yamin, Bohari M. [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, UKM 43600 Bangi, Selangor (Malaysia); Kassim, Mohammad B. [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, UKM 43600 Bangi, Selangor, Malaysia and Fuel Cell Institute, Universiti Kebangsaan Malaysia, UKM 43600 Bangi, Selangor (Malaysia)

2014-09-03

A simple mononuclear octahedral copper(II) complex was attempted from the reaction of three moles of 1-benzoyl-3-(pyridin-2-yl)-1H-pyrazole and one mole of copper(II) perchlorate hexahydrate in methanol. However, the product of the reaction was confirmed to be a dinuclear copper(II) complex with μ-(3-(pyridin-2-yl)-pyrazolato) and 3-(pyridin-2-yl)-1H-pyrazole ligands attached to each of the Cu(II) centre atom. The copper(II) ion assisted the cleavage of the C{sub benzoyl}description='Single-Bond' name='Single-Bond' value='Single-Bond'/>N bond afforded a 3-(pyridin-2-yl)-1H-pyrazole molecule. Deprotonation of the 3-(pyridin-2-yl)-1H-pyrazole gave a 3-(pyridin-2-yl)-pyrazolato, which subsequently reacted with the Cu(II) ion to give the (3-(pyridin-2-yl)-pyrazolato)(3-(pyridin-2-yl)-1H-pyrazole)Cu(II) product moiety. The structure of the dinuclear complex was confirmed by x-ray crystallography. The complex crystallized in a monoclinic crystal system with P2(1)/n space group and cell dimensions of a = 12.2029(8) Å, b = 11.4010(7) Å, c = 14.4052(9) Å and β = 102.414(2)°. The compound was further characterized by mass spectrometry, CHN elemental analysis, infrared and UV-visible spectroscopy and the results concurred with the x-ray structure. The presence of d-d transition at 671 nm (ε = 116 dm{sup 3} mol{sup −1} cm{sup −1}) supports the presence of Cu(II) centres.

Use of process indices for simplification of the description of vapor deposition systems

International Nuclear Information System (INIS)

Kajikawa, Yuya; Noda, Suguru; Komiyama, Hiroshi

2004-01-01

Vapor deposition is a complex process, including gas-phase, surface, and solid-phase phenomena. Because of the complexity of chemical and physical processes occurring in vapor deposition processes, it is difficult to form a comprehensive, fundamental understanding of vapor deposition and to control such systems for obtaining desirable structures and performance. To overcome this difficulty, we present a method for simplifying the complex description of such systems. One simplification method is to separate complex systems into multiple elements, and determine which of these are important elements. We call this method abridgement. The abridgement method retains only the dominant processes in a description of the system, and discards the others. Abridgement can be achieved by using process indices to evaluate the relative importance of the elementary processes. We describe the formulation and use of these process indices through examples of the growth of continuous films, initial deposition processes, and the formation of the preferred orientation of polycrystalline films. In this paper, we propose a method for representing complex vapor deposition processes as a set of simpler processes

Qualitative Description and Quantitative Optimization of Tactical Reconnaissance Agents System Organization

Directory of Open Access Journals (Sweden)

Xiong Li

2012-08-01

Full Text Available In this paper, the problem of qualitative description and quantitative optimization for tactical reconnaissance agents system organization is considered with objective of higher teamwork efficiency and more reasonable task balancing strategies. By analyzing tactical reconnaissance system and its environment, task-(role-entity agent mapping mechanism and agents in system organization, the system framework is qualitatively described. By transforming the system into an interaction task request-service mechanism queuing system, a Markov chain of system state transition is obtained, since its state transition process in interaction is Markov process and accords with real tactical reconnaissance behaviors. By solving the state transition equations, the inherent relationship of tactical reconnaissance agents is found and the optimized system configuration is obtained. The established simulation demonstration system proves that the proposed approach and model are feasible and effective.

Lot-sizing for a single-stage single-product production system with rework of perishable production defectives

NARCIS (Netherlands)

Teunter, R.; Flapper, S.D.P.

2003-01-01

We consider a single-stage single-product production system. Produced units may be non-defective, reworkable defective, or non-reworkable defective. The system switches between production and rework. After producing a fixed number (N) of units, all reworkable defective units are reworked. Reworkable

PROJECT W-551 INTERIM PRETREATMENT SYSTEM PRECONCEPTUAL CANDIDATE TECHNOLOGY DESCRIPTIONS

Energy Technology Data Exchange (ETDEWEB)

MAY TH

2008-08-12

The Office of River Protection (ORP) has authorized a study to recommend and select options for interim pretreatment of tank waste and support Waste Treatment Plant (WTP) low activity waste (LAW) operations prior to startup of all the WTP facilities. The Interim Pretreatment System (IPS) is to be a moderately sized system which separates entrained solids and 137Cs from tank waste for an interim time period while WTP high level waste vitrification and pretreatment facilities are completed. This study's objective is to prepare pre-conceptual technology descriptions that expand the technical detail for selected solid and cesium separation technologies. This revision includes information on additional feed tanks.

Charge transfer through single molecule contacts: How reliable are rate descriptions?

Directory of Open Access Journals (Sweden)

Denis Kast

2011-08-01

Full Text Available Background: The trend for the fabrication of electrical circuits with nanoscale dimensions has led to impressive progress in the field of molecular electronics in the last decade. However, a theoretical description of molecular contacts as the building blocks of future devices is challenging, as it has to combine the properties of Fermi liquids in the leads with charge and phonon degrees of freedom on the molecule. Outside of ab initio schemes for specific set-ups, generic models reveal the characteristics of transport processes. Particularly appealing are descriptions based on transfer rates successfully used in other contexts such as mesoscopic physics and intramolecular electron transfer. However, a detailed analysis of this scheme in comparison with numerically exact solutions is still elusive.Results: We show that a formulation in terms of transfer rates provides a quantitatively accurate description even in domains of parameter space where strictly it is expected to fail, e.g., at lower temperatures. Typically, intramolecular phonons are distributed according to a voltage driven steady state that can only roughly be captured by a thermal distribution with an effective elevated temperature (heating. An extension of a master equation for the charge–phonon complex, to effectively include the impact of off-diagonal elements of the reduced density matrix, provides very accurate solutions even for stronger electron–phonon coupling.Conclusion: Rate descriptions and master equations offer a versatile model to describe and understand charge transfer processes through molecular junctions. Such methods are computationally orders of magnitude less expensive than elaborate numerical simulations that, however, provide exact solutions as benchmarks. Adjustable parameters obtained, e.g., from ab initio calculations allow for the treatment of various realizations. Even though not as rigorously formulated as, e.g., nonequilibrium Green’s function

Image reconstruction of dynamic infrared single-pixel imaging system

Science.gov (United States)

Tong, Qi; Jiang, Yilin; Wang, Haiyan; Guo, Limin

2018-03-01

Single-pixel imaging technique has recently received much attention. Most of the current single-pixel imaging is aimed at relatively static targets or the imaging system is fixed, which is limited by the number of measurements received through the single detector. In this paper, we proposed a novel dynamic compressive imaging method to solve the imaging problem, where exists imaging system motion behavior, for the infrared (IR) rosette scanning system. The relationship between adjacent target images and scene is analyzed under different system movement scenarios. These relationships are used to build dynamic compressive imaging models. Simulation results demonstrate that the proposed method can improve the reconstruction quality of IR image and enhance the contrast between the target and the background in the presence of system movement.

Physical description of nuclear materials identification system (NMIS) signatures

International Nuclear Information System (INIS)

Mihalczo, J.T.; Mullens, J.A.; Mattingly, J.K.; Valentine, T.E.

2000-01-01

This paper describes all time and frequency analysis parameters measured with a new correlation processor (capability up to 1 GHz sampling rates and up to five input data channels) for three input channels: (1) the 252 Cf source ionization chamber; (2) a detection channel; and (3) a second detection channel. An intuitive and physical description of the various measured quantities is given as well as a brief mathematical description and a brief description of how the data are acquired. If the full five-channel capability is used, the number of measured quantities increases in number but not in type. The parameters provided by this new processor can be divided into two general classes: time analysis signatures and their related frequency analysis signatures. The time analysis signatures include the number of time m pulses occurs in a time interval, that is triggered randomly, upon a detection event, or upon a source fission event triggered. From the number of pulses in a time interval, the moments, factorial moments, and Feynmann variance can be obtained. Recent implementations of third- and fourth-order time and frequency analysis signatures in this processor are also briefly described. Thus, this processor used with a timed source of input neutrons contains all of the information from a pulsed neutron measurement, one and two detector Rossi-α measurements, multiplicity measurements, and third- and fourth-order correlation functions. This processor, although originally designed for active measurements with a 252 Cf interrogating source, has been successfully used passively (without 252 Cf source) for systems with inherent neutron sources such as fissile systems of plutonium. Data from active measurements with an 18.75 kg highly enriched uranium (93.2 wt%, 235 U) metal casting for storage are presented to illustrate some of the various time and frequency analysis parameters. This processor, which is a five-channel time correlation analyzer with time channel widths

Identification of characteristics and frequent scenarios of single-vehicle rollover crashes during pre-ballistic phase; part 1 - A descriptive study.

Science.gov (United States)

Kim, Taewung; Bose, Dipan; Foster, Jon; Bollapragada, Varun; Crandall, Jeff R; Clauser, Mark; Kerrigan, Jason R

2017-10-01

This study aimed to identify common patterns of pre-ballistic vehicle kinematics and roadway characteristics of real-world rollover crashes. Rollover crashes that were enrolled in the National Automotive Sampling System-Crashworthiness Data System (NASS-CDS) between the years 2000 and 2010 were analyzed. A descriptive analysis was performed to understand the characteristics of the pre-ballistic phase. Also, a frequency based pattern analysis was performed using a selection of NASS-CDS variables describing the pre-ballistic vehicle kinematics and roadway characteristics to rank common pathways of rollover crashes. Most case vehicles departed the road due to a loss of control/traction (LOC) (61%). The road departure with LOC was found to be 13.4 times more likely to occur with slippery road conditions compared to dry conditions. The vehicle was typically laterally skidding with yawing prior to a rollover (66%). Most case vehicles tripped over (82%) mostly at roadside/median (69%). The tripping force was applied to the wheels/tires (82%) from the ground (79%). The combination of these six most frequent attributes resulted in the most common scenario, which accounted for 26% of the entire cases. Large proportion of road departure with LOC (61%) implies electronic stability control (ESC) systems being an effective countermeasure for preventing single-vehicle rollover crashes. Furthermore, the correlation between the road departure with LOC and the reduced friction limit suggests the necessity of the performance evaluation of ESC under compromised road surface condition. Copyright © 2017 Elsevier Ltd. All rights reserved.

Wave kinematics and response of slender offshore structures. Vol 3: Description of measuring systems

Energy Technology Data Exchange (ETDEWEB)

Riber, H.J.

1999-08-01

The report presents the measuring systems used during the measurements in the North Sea at the Tyra field. The report consists of two parts: (1) Description of the wave measuring systems (WMS); (2) Description of the load mesuring system (LMS). The developed Wave Kinematics Measuring Systems (WMS) is an acoustic system based on the pulsed incoherent Doppler technique. Basically it consists of 4 sonar stations and a control and monitoring station. The sonar stations are positioned at the seabed north of the TCP-A platform in a star configuration with one station surrounded by the other three stations in a fixed distance of 37 m. From the central sonar stations an umbilical is routed to the TCP-A platform where the control and monitoring stations is positioned in the satellite communication room. The measurement periods have been concentrated to periods with storms. It was a special emphasis to measure the wave kinematics of extremely high waves. The LMS is described in terms of geometrical data, structural properties, instrumentation, and other characteristics. (LN)

Generalized oscillator systems and their parabosonic interpretation

Energy Technology Data Exchange (ETDEWEB)

Macfarlane, A J [Cambridge Univ. (United Kingdom). Dept. of Applied Mathematics and Theoretical Physics

1994-12-31

The Fock space description of various bosonic oscillator systems are carried out. All descriptions are based on a single creation - annihilation pair. Special attention is paid to the q-deformed Calogero-Vasiliev oscillator. 23 refs.

The First Organ-Based Ontology for Arthropods (Ontology of Arthropod Circulatory Systems - OArCS) and its Integration into a Novel Formalization Scheme for Morphological Descriptions.

Science.gov (United States)

Wirkner, Christian S; Göpel, Torben; Runge, Jens; Keiler, Jonas; Klussmann-Fricke, Bastian-Jesper; Huckstorf, Katarina; Scholz, Stephan; Mikó, István; J Yoder, Matthew; Richter, Stefan

2017-09-01

ontology. That is, descriptions in ontologies are only descriptions of individuals if they are necessary/and or sufficient representations of attributes (independently) observed and recorded for an individual. In addition, we here present for the first time an entirely new approach to formalizing phenotypic research, a semantic model for the description of a complex organ system in a highly disparate taxon, the arthropods. We demonstrate this with a formalized morphological description of the hemolymph vascular system in one specimen of the European garden spider Araneus diadematus. Our description targets five categories of descriptive statement: "position", "spatial relationships", "shape", "constituents", and "connections", as the corresponding formalizations constitute exemplary patterns useful not only when talking about the circulatory system, but also in descriptions in general. The downstream applications of computer-parsable morphological descriptions are widespread, with their core utility being the fact that they make it possible to compare collective description sets in computational time, that is, very quickly. Among other things, this facilitates the identification of phenotypic plasticity and variation when single individuals are compared, the identification of those traits which correlate between and within taxa, and the identification of links between morphological traits and genetic (using GO, Gene Ontology) or environmental (using ENVO, Environmental Ontology) factors. [Arthropoda; concept; function; hemolymph vascular system; homology; terminology.]. © The Author(s) 2017. Published by Oxford University Press, on behalf of the Society of Systematic Biologists. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Initial Single-Shell Tank Retrieval System mission analysis report

International Nuclear Information System (INIS)

Hertzel, J.S.

1996-03-01

This document provides the mission analysis for the Initial Single-Shell Tank Retrieval System task, which supports the Single-Shell Tank Waste Retrieval Program in its commitment to remove waste from single-shell tanks for treatment and final closure

Valve system incorporating single failure protection logic

Science.gov (United States)

Ryan, Rodger; Timmerman, Walter J. H.

1980-01-01

A valve system incorporating single failure protective logic. The system consists of a valve combination or composite valve which allows actuation or de-actuation of a device such as a hydraulic cylinder or other mechanism, integral with or separate from the valve assembly, by means of three independent input signals combined in a function commonly known as two-out-of-three logic. Using the input signals as independent and redundant actuation/de-actuation signals, a single signal failure, or failure of the corresponding valve or valve set, will neither prevent the desired action, nor cause the undesired action of the mechanism.

Case study of a grid connected with a battery photovoltaic system: V-trough concentration vs. single-axis tracking

International Nuclear Information System (INIS)

Tina, G.M.; Scandura, P.F.

2012-01-01

Highlights: ► PV systems with sun tracking and concentrators (CPVS) can reduce the cost of energy per kWh produced. ► The V-trough low-concentration system solution is compatible with flat PV module technologies. ► Optical, thermal and electrical models are needed to forecast real power production. ► The description of a PV grid connected system with batteries, a one-axis tracker and CPV photovoltaic system is presented. ► Outdoor measurements of the generating system are provided and discussed. - Abstract: Photovoltaic systems (PVSs) combined with either some form of storage, such as a battery energy storage system (BESS), or direct load control, can play a crucial role in achieving a more economical operation of the electric utility system while enhancing its reliability with additional energy sources. At the same time, it is also important to use cost-effective PV solutions. In this context, a low-concentration PVS (CPVS) is analysed as a feasible alternative. This paper, present a case study of a complex PVS, composed of two PVSs, a storage system (BEES) and an inverter that allows the system to operate in both the island and grid-connected modes. The first PVS, is a 2.76-kWp single-axis tracking system (azimuth) with modules facing south and tilted 30°, while the second PVS is a dual-axis tracking system, rated 860 Wp, consisting of a concentrator at the flat mirrors (DoubleSun® Four). The system is installed on the roof of the main building of the “ITIS Marconi” school (Italy). A detailed description of the system is provided, and preliminary operating data are presented and discussed. The efficiencies of the PV systems are calculated and measured to evaluate the cost effectiveness of a low-concentration system.

Overview of Single-Phase Grid-Connected Photovoltaic Systems

DEFF Research Database (Denmark)

Yang, Yongheng; Blaabjerg, Frede

2017-01-01

A continuous booming installation of solar photovoltaic (PV) systems has been witnessed worldwide. It is mainly driven by the imperative demand of “clean” power generation from renewables. Grid-connected PV systems will thus become an even more active player in the future mixed power systems, which...... systems. This chapter thus gives an overview of the advancement of power electronics converters in single-phase grid-connected PV systems, being commonly used in residential applications. Demands to single-phase grid-connected PV systems and the general control strategies are also addressed...... are linked together by a vast of power electronics converters and the power grid. In order to achieve a reliable and efficient power generation from PV systems, more stringent demands have been imposed on the entire PV system. It, in return, advances the development of the power converter technology in PV...

System Design Description and Requirements for Modeling the Off-Gas Systems for Fuel Recycling Facilities

Energy Technology Data Exchange (ETDEWEB)

Daryl R. Haefner; Jack D. Law; Troy J. Tranter

2010-08-01

This document provides descriptions of the off-gases evolved during spent nuclear fuel processing and the systems used to capture the gases of concern. Two reprocessing techniques are discussed, namely aqueous separations and electrochemical (pyrochemical) processing. The unit operations associated with each process are described in enough detail so that computer models to mimic their behavior can be developed. The document also lists the general requirements for the desired computer models.

Modeling of the interplay between single-file diffusion and conversion reaction in mesoporous systems

Energy Technology Data Exchange (ETDEWEB)

Wang, Jing [Iowa State Univ., Ames, IA (United States)

2013-01-11

We analyze the spatiotemporal behavior of species concentrations in a diffusion-mediated conversion reaction which occurs at catalytic sites within linear pores of nanometer diameter. A strict single-file (no passing) constraint occurs in the diffusion within such narrow pores. Both transient and steady-state behavior is precisely characterized by kinetic Monte Carlo simulations of a spatially discrete lattice–gas model for this reaction–diffusion process considering various distributions of catalytic sites. Exact hierarchical master equations can also be developed for this model. Their analysis, after application of mean-field type truncation approximations, produces discrete reaction–diffusion type equations (mf-RDE). For slowly varying concentrations, we further develop coarse-grained continuum hydrodynamic reaction–diffusion equations (h-RDE) incorporating a precise treatment of single-file diffusion (SFD) in this multispecies system. Noting the shortcomings of mf-RDE and h-RDE, we then develop a generalized hydrodynamic (GH) formulation of appropriate gh-RDE which incorporates an unconventional description of chemical diffusion in mixed-component quasi-single-file systems based on a refined picture of tracer diffusion for finite-length pores. The gh-RDE elucidate the non-exponential decay of the steady-state reactant concentration into the pore and the non-mean-field scaling of the reactant penetration depth. Then an extended model of a catalytic conversion reaction within a functionalized nanoporous material is developed to assess the effect of varying the reaction product – pore interior interaction from attractive to repulsive. The analysis is performed utilizing the generalized hydrodynamic formulation of the reaction-diffusion equations which can reliably capture the complex interplay between reaction and restricted transport for both irreversible and reversible reactions.

Single-molecule imaging and manipulation of biomolecular machines and systems.

Science.gov (United States)

Iino, Ryota; Iida, Tatsuya; Nakamura, Akihiko; Saita, Ei-Ichiro; You, Huijuan; Sako, Yasushi

2018-02-01

Biological molecular machines support various activities and behaviors of cells, such as energy production, signal transduction, growth, differentiation, and migration. We provide an overview of single-molecule imaging methods involving both small and large probes used to monitor the dynamic motions of molecular machines in vitro (purified proteins) and in living cells, and single-molecule manipulation methods used to measure the forces, mechanical properties and responses of biomolecules. We also introduce several examples of single-molecule analysis, focusing primarily on motor proteins and signal transduction systems. Single-molecule analysis is a powerful approach to unveil the operational mechanisms both of individual molecular machines and of systems consisting of many molecular machines. Quantitative, high-resolution single-molecule analyses of biomolecular systems at the various hierarchies of life will help to answer our fundamental question: "What is life?" This article is part of a Special Issue entitled "Biophysical Exploration of Dynamical Ordering of Biomolecular Systems" edited by Dr. Koichi Kato. Copyright © 2017 Elsevier B.V. All rights reserved.

Licensee Event Report system: description of system and guidelines for reporting

International Nuclear Information System (INIS)

Hebdon, F.J.

1983-09-01

On July 26, 1983, the Commission published in the Federal Register a final rule (10 CFR 50.73) that modifies and codifies the Licensee Event Report (LER) system. The rule becomes effective on January 1, 1984. This NUREG provides supporting information and guidance that will be of interest to persons responsible for the preparation and review of LERs. The information contained in this NUREG includes: (1) a brief description of how LERs are analyzed by the NRC; (2) a restatement of the guidance contained in the Statement of Consideration that accompanied the publication of the LER rule; (3) a set of examples of potentially reportable events with staff comments on the actual reportability of each event; (4) guidance on how to prepare an LER, including the LER forms; and (5) guidance on submittal of LERs

The descriptive properties of prescriptive theories: an application of systems thinking in data warehousing

Directory of Open Access Journals (Sweden)

Roelien Goede

2012-12-01

Full Text Available Information systems and in particular data warehouses are very expensive systems to develop. It is therefore not advisable to experiment with ideas too different from current practices. This makes it difficult to apply prescriptive theories in an existing field. From theoretical considerations one might want to develop a data warehouse according to another method such as critical systems thinking methodology. It is however very difficult to persuade data warehouse practitioners to attempt such an experiment. This might be because they would rather adhere to known practices or that they are not sufficiently knowledgeable on critical systems thinking (or any other prescriptive theory to apply it to such an expensive project. This paper describes a method in which prescriptive theories may be used descriptively to analyse their applicability in a specific field of application. The proposed method is used to understand the practices of the data warehouse discipline from the perspectives of the systems thinking discipline. It is also indicated how this method could be used in other studies where the behaviour of participants is viewed from a point of view of which the detail are unknown to the participants. Keywords: Data warehousing, Systems thinking, Prescriptive theory, Descriptive theory, Interpretative research. Disciplines: Information technology, systems theory, data warehousing, hermeneutics

Software Test Description (STD) for the Globally Relocatable Navy Tide/Atmospheric Modeling System (PCTides)

National Research Council Canada - National Science Library

Posey, Pamela

2002-01-01

The purpose of this Software Test Description (STD) is to establish formal test cases to be used by personnel tasked with the installation and verification of the Globally Relocatable Navy Tide/Atmospheric Modeling System (PCTides...

Converting Taxonomic Descriptions to New Digital Formats

Directory of Open Access Journals (Sweden)

Hong Cui

2008-01-01

Full Text Available Abstract.--The majority of taxonomic descriptions is currently in print format. The majority of digital descriptions are in formats such as DOC, HTML, or PDF and for human readers. These formats do not convey rich semantics in taxonomic descriptions for computer-aided process. Newer digital formats such as XML and RDF accommodate semantic annotations that allow computers to process the rich semantics on human's behalf, thus open up opportunities for a wide range of innovative usages of taxonomic descriptions, such as searching in more precise and flexible ways, integrating with gnomic and geographic information, generating taxonomic keys automatically, and text data mining and information visualization etc. This paper discusses the challenges in automated conversion of multiple collections of descriptions to XML format and reports an automated system, MARTT. MARTT is a machine-learning system that makes use of training examples to tag new descriptions into XML format. A number of utilities are implemented as solutions to the challenges. The utilities are used to reduce the effort for training example preparation, to facilitate the creation of a comprehensive schema, and to predict system performance on a new collection of descriptions. The system has been tested with several plant and alga taxonomic publications including Flora of China and Flora of North America.

Failure of single electron descriptions of molecular orbital collision processes. [Electron promotion mechanism

Energy Technology Data Exchange (ETDEWEB)

Elston, S.B.

1978-01-01

Inner-shell excitation occurring in low and moderate (keV range) energy collisions between light atomic and ionic systems is frequently describable in terms of molecular promotion mechanisms, which were extensively explored both theoretically and experimentally. The bulk of such studies have concentrated on processes understandable through the use of single- and independent-electron models. Nonetheless, it is possible to find cases of inner-shell excitation in relatively simple collision systems which involve nearly simultaneous multiple-electron transitions and transitions induced by inherently two-electron interactions. Evidence for these many- and nonindependent-electron phenomena in inner-shell excitation processes and the importance of considering such effects in the interpretation of collisionally induced excitation spectra is discussed. 13 references.

Knowledge-based driver assistance systems traffic situation description and situation feature relevance

CERN Document Server

Huelsen, Michael

2014-01-01

The comprehension of a traffic situation plays a major role in driving a vehicle. Interpretable information forms a basis for future projection, decision making and action performing, such as navigating, maneuvering and driving control. Michael Huelsen provides an ontology-based generic traffic situation description capable of supplying various advanced driver assistance systems with relevant information about the current traffic situation of a vehicle and its environment. These systems are enabled to perform reasonable actions and approach visionary goals such as injury and accident free driv

ASSEMBLY TRANSFER SYSTEM DESCRIPTION DOCUMENT

International Nuclear Information System (INIS)

Gorpani, B.

2000-01-01

The Assembly Transfer System (ATS) receives, cools, and opens rail and truck transportation casks from the Carrier/Cask Handling System (CCHS). The system unloads transportation casks consisting of bare Spent Nuclear Fuel (SNF) assemblies, single element canisters, and Dual Purpose Canisters (DPCs). For casks containing DPCs, the system opens the DPCs and unloads the SNF. The system stages the assemblies, transfer assemblies to and from fuel-blending inventory pools, loads them into Disposal Containers (DCs), temporarily seals and inerts the DC, decontaminates the DC and transfers it to the Disposal Container Handling System. The system also prepares empty casks and DPCs for off-site shipment. Two identical Assembly Transfer System lines are provided in the Waste Handling Building (WHB). Each line operates independently to handle the waste transfer throughput and to support maintenance operations. Each system line primarily consists of wet and dry handling areas. The wet handling area includes a cask transport system, cask and DPC preparation system, and a wet assembly handling system. The basket transport system forms the transition between the wet and dry handling areas. The dry handling area includes the dry assembly handling system, assembly drying system, DC preparation system, and DC transport system. Both the wet and dry handling areas are controlled by the control and tracking system. The system operating sequence begins with moving transportation casks to the cask preparation area. The cask preparation operations consist of cask cavity gas sampling, cask venting, cask cool-down, outer lid removal, and inner shield plug lifting fixture attachment. Casks containing bare SNF (no DPC) are filled with water and placed in the cask unloading pool. The inner shield plugs are removed underwater. For casks containing a DPC, the cask lid(s) is removed, and the DPC is penetrated, sampled, vented, and cooled. A DPC lifting fixture is attached and the cask is placed

System and method for single-phase, single-stage grid-interactive inverter

Science.gov (United States)

Liu, Liming; Li, Hui

2015-09-01

The present invention provides for the integration of distributed renewable energy sources/storages utilizing a cascaded DC-AC inverter, thereby eliminating the need for a DC-DC converter. The ability to segment the energy sources and energy storages improves the maintenance capability and system reliability of the distributed generation system, as well as achieve wide range reactive power compensation. In the absence of a DC-DC converter, single stage energy conversion can be achieved to enhance energy conversion efficiency.

Reliability and reproducibility of subaxial cervical injury description system: a standardized nomenclature schema.

Science.gov (United States)

Bono, Christopher M; Schoenfeld, Andrew; Gupta, Giri; Harrop, James S; Anderson, Paul; Patel, Alpesh A; Dimar, John; Aarabi, Bizhan; Dailey, Andrew; Vaccaro, Alexander R; Gahr, Ralf; Shaffrey, Christopher; Anderson, David G; Rampersaud, Raj

2011-08-01

Radiographic measurement study. To develop a standardized cervical injury nomenclature system to facilitate description, communication, and classification among health care providers. The reliability and reproducibility of this system was then examined. Description of subaxial cervical injuries is critical for treatment decision making and comparing scientific reports of outcomes. Despite a number of available classification systems, surgeons, and researchers continue to use descriptive nomenclature, such as "burst" and "teardrop" fractures, to describe injuries. However, there is considerable inconsistency with use of such terms in the literature. Eleven distinct injury types and associated definitions were established for the subaxial cervical spine and subsequently refined by members of the Spine Trauma Study Group. A series of 18 cases of patients with a broad spectrum of subaxial cervical spine injuries was prepared and distributed to surgeon raters. Each rater was provided with the full nomenclature document and asked to select primary and secondary injury types for each case. After receipt of the raters' first round of classifications, the cases were resorted and returned to the raters for a second round of review. Interrater and intrarater reliabilities were calculated as percent agreement and Cohen kappa (κ) values. Intrarater reliability was assessed by comparing a given rater's diagnosis from the first and second rounds. Nineteen surgeons completed the first and second rounds of the study. Overall, the system demonstrated 56.4% interrater agreement and 72.8% intrarater agreement. Overall, interrater κ values demonstrated moderate agreement while intrarater κ values showed substantial agreement. Analyzed by injury types, only four (burst fractures, lateral mass fractures, flexion teardrop fractures, and anterior distraction injuries) demonstrated greater than 50% interrater agreement. This study demonstrated that, even in ideal circumstances, there is

On the validity of collective variable description of Bose systems

International Nuclear Information System (INIS)

Takahashi, Minoru

1975-01-01

The validity of Sunakawa, Yamasaki and Kebukawa's Hamiltonian and that of Bogoliubov and Zubarev's Hamiltonian are examined. Perturbational expansion of the ground state energy by these Hamiltonians disagrees with the exact solution of Lieb and Liniger for one-dimensional Bose system with repulsive delta-function interaction. This fact suggests that these Hamiltonians are not microscopic descriptions of the many-Boson system. Mathematical inconsistency in Bogoliubov and Zubarev's theory is also pointed out. Moreover analytic expression of high density expansion for the ground state energy density e 0 is found out to be e 0 n -3 =γ-(4/3π)γsup(3/2)+(1/6-1/π 2 )γ 2 +O(γsup(5/2)), γ=c/n, for one-dimensional Bose system with delta function interaction (density n, strength 2c, h=2m=1) by the use of the correlated basis function method. (auth.)

The water reactor safety research project index: a description of the computerized system for its databank

International Nuclear Information System (INIS)

Della Loggia, E.; Primavera, R.

1993-01-01

The water reactor nuclear safety research project index has been published by the CEC for many years as a compilation of information on research projects relating to LWR nuclear safety. Since 1981, it has been published, alternatively with NEA (OECD), every second year. The number of contributions from research organizations in Community member countries has steadily increased and reached the level of 1 700 pages, in which more than 600 project descriptions have been collected. In 1988, for the first time, the document was produced using a computerized system developed with the assistance of the ISEI (Institute for Systems Engineering and Informatics) of JRC Ispra. The data have been stored in a computer based in Ispra. The system allows searching a preselected set of subjects through the information stored in the computer: it makes the updating of the projects description much easier and makes the retrieval of the data possible. This report presents a short description of the computerized system developed for the databank of the index. The computerized system presented in this report is structured in a quite general way and for that reason can be adapted very easily to every field where a databank needs to be constituted in order to collect extended information on several projects. (authors). 6 figs., 5 tabs., 5 refs

Data Description Exchange Services for Heterogeneous Vehicle and Spaceport Control and Monitor Systems, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — CCT proposes an advanced data description exchange approach for space/spaceport systems that will provide a generic platform independent software capability for...

48 CFR 52.214-21 - Descriptive Literature.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Descriptive Literature. 52....214-21 Descriptive Literature. As prescribed in 14.201-6(p)(1), insert the following provision: Descriptive Literature (APR 2002) (a) Descriptive literature, as used in this provision, means information...

Summary description of the Babcock and Wilcox integrated nuclear design system

International Nuclear Information System (INIS)

Wittkopf, W.A.

1976-03-01

The Babcock and Wilcox integrated nuclear design system is divided into three broad areas: basic nuclear data processing, applications data processing, and nuclear design calculations. In basic nuclear data processing, basic nuclear data are collected, evaluated, and processed into a specified fine-energy mesh multigroup data file called a Master Library. In applications data processing, data for selected materials are retrieved from the Master Library and processed into an optimally structured, multigroup Production Library. Using these data and input descriptions of cells or regions, neutron spectra are generated and few-group constants are computed and fitted as a function of fuel burnup, initial enrichment, temperature, etc. In nuclear design calculations, few-group cross-section fits and descriptions of each core region and core geometry are input to a diffusion-depletion program or a nodal program that computes core reactivity, core power distribution, control rod worth, fuel cycle studies, core operating limitations, etc

Non-reversible evolution of quantum chaotic system. Kinetic description

International Nuclear Information System (INIS)

Chotorlishvili, L.; Skrinnikov, V.

2008-01-01

It is well known that the appearance of non-reversibility in classical chaotic systems is connected with a local instability of phase trajectories relatively to a small change of initial conditions and parameters of the system. Classical chaotic systems reveal an exponential sensitivity to these changes. This leads to an exponential growth of initial error with time, and as the result after the statistical averaging over this error, the dynamics of the system becomes non-reversible. In spite of this, the question about the origin of non-reversibility in quantum case remains actual. The point is that the classical notion of instability of phase trajectories loses its sense during quantum consideration. The current work is dedicated to the clarification of the origin of non-reversibility in quantum chaotic systems. For this purpose we study a non-stationary dynamics of the chaotic quantum system. By analogy with classical chaos, we consider an influence of a small unavoidable error of the parameter of the system on the non-reversibility of the dynamics. It is shown in the Letter that due to the peculiarity of chaotic quantum systems, the statistical averaging over the small unavoidable error leads to the non-reversible transition from the pure state into the mixed one. The second part of the Letter is dedicated to the kinematic description of the chaotic quantum-mechanical system. Using the formalism of superoperators, a muster kinematic equation for chaotic quantum system was obtained from Liouville equation under a strict mathematical consideration

An object model for beamline descriptions

International Nuclear Information System (INIS)

Hill, B.W.; Martono, H.; Gillespie, J.S.

1997-01-01

Translation of beamline model descriptions between different accelerator codes presents a unique challenge due to the different representations used for various elements and subsystems. These differences range from simple units conversions to more complex translations involving multiple beamline components. A representation of basic accelerator components is being developed in order to define a meta-structure from which beamline models, in different codes, can be described and to facilitate the translation of models between these codes. Sublines of basic components will be used to represent more complex beamline descriptions and bridge the gap between codes which may represent a beamline element as a single entity, and those which use multiple elements to describe the same physical device. A C++ object model for supporting this beamline description and a grammar for describing beamlines in terms of these components is being developed. The object model will support a common graphic user interface and translation filters for representing native beamline descriptions for a variety of accelerator codes. An overview of our work on the object model for beamline descriptions is presented here. copyright 1997 American Institute of Physics

Energy dependence of critical state of single-component systems

International Nuclear Information System (INIS)

Volchenkova, R.A.

1985-01-01

Equations of critical states of the single-component systems: Psub(cr)(/Psub(o)=(Tsub(cr)/Tsub(o))x0.73, Tsub(cr)=K(Tsub(boil))sup(1.116) and Hsub(cr)(/Hsub(B)=Tsub(sr)/Tsub(B))sup(1.48) where Tsub(B)=1K, Hsub(B)-2 kcal/g-at, K-dimension factor are presented. It is shown that the revealed dependence Hsub(cr)=H(Tsub(cr)) is an energy boundary of a liquid-vapour phase state of the single-component systems beyond limits of which difference between liquid and vapour phases vanishes in increasing the system energy content. The given equations of state are true for all the single-component systems and permit to consider physicomechanical properties of substances in dynamic state depending on external conditions. Critical temperatures and dependences for elements from the most fusible He to infusible W and Re have been calculated

The shape and dynamics of the generation of the splash forms in single-phase systems after drop hitting

Science.gov (United States)

Sochan, Agata; Beczek, Michał; Mazur, Rafał; RyŻak, Magdalena; Bieganowski, Andrzej

2018-02-01

The splash phenomenon is being increasingly explored with the use of modern measurement tools, including the high-speed cameras. Recording images at a rate of several thousand frames per second facilitates parameterization and description of the dynamics of splash phases. This paper describes the impact of a single drop of a liquid falling on the surface of the same liquid. Three single-phase liquid systems, i.e., water, petrol, and diesel fuel, were examined. The falling drops were characterized by different kinetic energy values depending on the height of the fall, which ranged from 0.1 to 7.0 m. Four forms, i.e., waves, crowns, semi-closed domes, and domes, were distinguished depending on the drop energy. The analysis of the recorded images facilitated determination of the static and dynamic parameters of each form, e.g., the maximum height of each splash form, the width of the splash form at its maximum height, and the rate of growth of the splash form. We, Re, Fr, and K numbers were determined for all analyzed liquid systems. On the basis of the obtained values of dimensionless numbers, the areas of occurrence of characteristic splash forms were separated.

Chemical Transfer (Single Small-Scale) Facility

Data.gov (United States)

Federal Laboratory Consortium — Description/History: Chemistry laboratoryThe Chemical Transfer Facility (CTF)  is the only U.S. single small-scale  facility, a single repository for the Army’s...

Formalizing the Problem of Music Description

DEFF Research Database (Denmark)

Sturm, Bob L.; Bardeli, Rolf; Langlois, Thibault

2015-01-01

The lack of a formalism for “the problem of music descrip- tion” results in, among other things: ambiguity in what problem a music description system must address, how it should be evaluated, what criteria define its success, and the paradox that a music description system can reproduce the “ground...

Advanced Transport Operating System (ATOPS) Flight Management/Flight Controls (FM/FC) software description

Science.gov (United States)

Wolverton, David A.; Dickson, Richard W.; Clinedinst, Winston C.; Slominski, Christopher J.

1993-01-01

The flight software developed for the Flight Management/Flight Controls (FM/FC) MicroVAX computer used on the Transport Systems Research Vehicle for Advanced Transport Operating Systems (ATOPS) research is described. The FM/FC software computes navigation position estimates, guidance commands, and those commands issued to the control surfaces to direct the aircraft in flight. Various modes of flight are provided for, ranging from computer assisted manual modes to fully automatic modes including automatic landing. A high-level system overview as well as a description of each software module comprising the system is provided. Digital systems diagrams are included for each major flight control component and selected flight management functions.

Computer systems and software description for Standard-E+ Hydrogen Monitoring System (SHMS-E+)

International Nuclear Information System (INIS)

Tate, D.D.

1997-01-01

The primary function of the Standard-E+ Hydrogen Monitoring System (SHMS-E+) is to determine tank vapor space gas composition and gas release rate, and to detect gas release events. Characterization of the gas composition is needed for safety analyses. The lower flammability limit, as well as the peak burn temperature and pressure, are dependent upon the gas composition. If there is little or no knowledge about the gas composition, safety analyses utilize compositions that yield the worst case in a deflagration or detonation. Knowledge of the true composition could lead to reductions in the assumptions and therefore there may be a potential for a reduction in controls and work restrictions. Also, knowledge of the actual composition will be required information for the analysis that is needed to remove tanks from the Watch List. Similarly, the rate of generation and release of gases is required information for performing safety analyses, developing controls, designing equipment, and closing safety issues. This report outlines the computer system design layout description for the Standard-E+ Hydrogen Monitoring System

Integrated Visualisation and Description of Complex Systems

National Research Council Canada - National Science Library

Goodburn, D

1999-01-01

.... Guided by a conceptual model of a description process that is driven by user information needs within a domain context, the approach incorporates the use of novel visualization techniques based...

Assessing the Nonequilibrium Thermodynamics in a Quenched Quantum Many-Body System via Single Projective Measurements

Directory of Open Access Journals (Sweden)

L. Fusco

2014-08-01

Full Text Available We analyze the nature of the statistics of the work done on or by a quantum many-body system brought out of equilibrium. We show that, for the sudden quench and for an initial state that commutes with the initial Hamiltonian, it is possible to retrieve the whole nonequilibrium thermodynamics via single projective measurements of observables. We highlight, in a physically clear way, the qualitative implications for the statistics of work coming from considering processes described by operators that either commute or do not commute with the unperturbed Hamiltonian of a given system. We consider a quantum many-body system and derive an expression that allows us to give a physical interpretation, for a thermal initial state, to all of the cumulants of the work in the case of quenched operators commuting with the unperturbed Hamiltonian. In the commuting case, the observables that we need to measure have an intuitive physical meaning. Conversely, in the noncommuting case, we show that, although it is possible to operate fully within the single-measurement framework irrespectively of the size of the quench, some difficulties are faced in providing a clear-cut physical interpretation to the cumulants. This circumstance makes the study of the physics of the system nontrivial and highlights the nonintuitive phenomenology of the emergence of thermodynamics from the fully quantum microscopic description. We illustrate our ideas with the example of the Ising model in a transverse field showing the interesting behavior of the high-order statistical moments of the work distribution for a generic thermal state and linking them to the critical nature of the model itself.

Optical measuring system with an interrogator and a polymer-based single-mode fibre optic sensor system

DEFF Research Database (Denmark)

2017-01-01

The present invention relates to an optical measuring system comprising a polymer-based single-mode fibre-optic sensor system (102), an optical interrogator (101), and an optical arrangement (103) interconnecting the optical interrogator (101) and the polymer-based single-mode fibre-optic sensor...... system (102). The invention further relates to an optical interrogator adapted to be connected to a polymer-based single-mode fibre-optic sensor system via an optical arrangement. The interrogator comprises a broadband light source arrangement (104) and a spectrum analysing arrangement which receives...

Analysis of the possibility of SysML and BPMN application in formal data acquisition system description

Science.gov (United States)

Ćwikła, G.; Gwiazda, A.; Banaś, W.; Monica, Z.; Foit, K.

2017-08-01

The article presents the study of possible application of selected methods of complex description, that can be used as a support of the Manufacturing Information Acquisition System (MIAS) methodology, describing how to design a data acquisition system, allowing for collecting and processing real-time data on the functioning of a production system, necessary for management of a company. MIAS can allow conversion into Cyber-Physical Production System. MIAS is gathering and pre-processing data on the state of production system, including e.g. realisation of production orders, state of machines, materials and human resources. Systematised approach and model-based development is proposed for improving the quality of the design of MIAS methodology-based complex systems supporting data acquisition in various types of companies. Graphical specification can be the baseline for any model-based development in specified areas. The possibility of application of SysML and BPMN, both being UML-based languages, representing different approaches to modelling of requirements, architecture and implementation of the data acquisition system, as a tools supporting description of required features of MIAS, were considered.

System requirements and design description for the environmental requirements management interface (ERMI)

International Nuclear Information System (INIS)

Biebesheimer, E.

1997-01-01

This document describes system requirements and the design description for the Environmental Requirements Management Interface (ERMI). The ERMI database assists Tank Farm personnel with scheduling, planning, and documenting procedure compliance, performance verification, and selected corrective action tracking activities for Tank Farm S/RID requirements. The ERMI database was developed by Science Applications International Corporation (SAIC). This document was prepared by SAIC and edited by LMHC

On the microcanonical description D-brane thermodynamics

International Nuclear Information System (INIS)

Meana, Marco Laucelli; Penalba, Jesus Puente

1999-01-01

We study the microcanonical description of string gases in the presence of D-branes. We obtain exact expressions for the single string density of states and draw the regions in phase space where asymptotic approximations are valid. We are able to describe the whole range of energies including the SYM phase of the D-branes and we remark the importance of the infrared cut-off used in the high energy approximations. With the complete expression we can obtain the density of states of the multiple string gas and study its thermal properties, showing that the Hagedorn temperature is maximum for every system and there is never a phase transition whenever there is thermal contact among the strings attached to different D-branes

Fascia: a morphological description and classification system based on a literature review

Science.gov (United States)

Kumka, Myroslava; Bonar, Jason

2012-01-01

Fascia is virtually inseparable from all structures in the body and acts to create continuity amongst tissues to enhance function and support. In the past fascia has been difficult to study leading to ambiguities in nomenclature, which have only recently been addressed. Through review of the available literature, advances in fascia research were compiled, and issues related to terminology, descriptions, and clinical relevance of fascia were addressed. Our multimodal search strategy was conducted in Medline and PubMed databases, with other targeted searches in Google Scholar and by hand, utilizing reference lists and conference proceedings. In an effort to organize nomenclature for fascial structures provided by the Federative International Committee on Anatomical Terminology (FICAT), we developed a functional classification system which includes four categories of fascia: i) linking, ii) fascicular, iii) compression, and iv) separating fasciae. Each category was developed from descriptions in the literature on gross anatomy, histology, and biomechanics; the category names reflect the function of the fascia. An up-to-date definition of fascia is provided, as well as descriptions of its function and clinical features. Our classification demonstrates the use of internationally accepted terminology in an ontology which can improve understanding of major terms in each category of fascia. PMID:22997468

QSpec: online control and data analysis system for single-cell Raman spectroscopy

Directory of Open Access Journals (Sweden)

Lihui Ren

2014-06-01

Full Text Available Single-cell phenotyping is critical to the success of biological reductionism. Raman-activated cell sorting (RACS has shown promise in resolving the dynamics of living cells at the individual level and to uncover population heterogeneities in comparison to established approaches such as fluorescence-activated cell sorting (FACS. Given that the number of single-cells would be massive in any experiment, the power of Raman profiling technique for single-cell analysis would be fully utilized only when coupled with a high-throughput and intelligent process control and data analysis system. In this work, we established QSpec, an automatic system that supports high-throughput Raman-based single-cell phenotyping. Additionally, a single-cell Raman profile database has been established upon which data-mining could be applied to discover the heterogeneity among single-cells under different conditions. To test the effectiveness of this control and data analysis system, a sub-system was also developed to simulate the phenotypes of single-cells as well as the device features.

Fourier-based linear systems description of free-breathing pulmonary magnetic resonance imaging

Science.gov (United States)

Capaldi, D. P. I.; Svenningsen, S.; Cunningham, I. A.; Parraga, G.

2015-03-01

Fourier-decomposition of free-breathing pulmonary magnetic resonance imaging (FDMRI) was recently piloted as a way to provide rapid quantitative pulmonary maps of ventilation and perfusion without the use of exogenous contrast agents. This method exploits fast pulmonary MRI acquisition of free-breathing proton (1H) pulmonary images and non-rigid registration to compensate for changes in position and shape of the thorax associated with breathing. In this way, ventilation imaging using conventional MRI systems can be undertaken but there has been no systematic evaluation of fundamental image quality measurements based on linear systems theory. We investigated the performance of free-breathing pulmonary ventilation imaging using a Fourier-based linear system description of each operation required to generate FDMRI ventilation maps. Twelve subjects with chronic obstructive pulmonary disease (COPD) or bronchiectasis underwent pulmonary function tests and MRI. Non-rigid registration was used to co-register the temporal series of pulmonary images. Pulmonary voxel intensities were aligned along a time axis and discrete Fourier transforms were performed on the periodic signal intensity pattern to generate frequency spectra. We determined the signal-to-noise ratio (SNR) of the FDMRI ventilation maps using a conventional approach (SNRC) and using the Fourier-based description (SNRF). Mean SNR was 4.7 ± 1.3 for subjects with bronchiectasis and 3.4 ± 1.8, for COPD subjects (p>.05). SNRF was significantly different than SNRC (p<.01). SNRF was approximately 50% of SNRC suggesting that the linear system model well-estimates the current approach.

Resolving the biophysics of axon transmembrane polarization in a single closed-form description

Energy Technology Data Exchange (ETDEWEB)

Melendy, Robert F., E-mail: rfmelendy@liberty.edu [School of Engineering and Computational Sciences, Liberty University, Lynchburg, Virginia 24515 (United States)

2015-12-28

When a depolarizing event occurs across a cell membrane there is a remarkable change in its electrical properties. A complete depolarization event produces a considerably rapid increase in voltage that propagates longitudinally along the axon and is accompanied by changes in axial conductance. A dynamically changing magnetic field is associated with the passage of the action potential down the axon. Over 75 years of research has gone into the quantification of this phenomenon. To date, no unified model exist that resolves transmembrane polarization in a closed-form description. Here, a simple but formative description of propagated signaling phenomena in the membrane of an axon is presented in closed-form. The focus is on using both biophysics and mathematical methods for elucidating the fundamental mechanisms governing transmembrane polarization. The results presented demonstrate how to resolve electromagnetic and thermodynamic factors that govern transmembrane potential. Computational results are supported by well-established quantitative descriptions of propagated signaling phenomena in the membrane of an axon. The findings demonstrate how intracellular conductance, the thermodynamics of magnetization, and current modulation function together in generating an action potential in a unified closed-form description. The work presented in this paper provides compelling evidence that three basic factors contribute to the propagated signaling in the membrane of an axon. It is anticipated this work will compel those in biophysics, physical biology, and in the computational neurosciences to probe deeper into the classical and quantum features of membrane magnetization and signaling. It is hoped that subsequent investigations of this sort will be advanced by the computational features of this model without having to resort to numerical methods of analysis.

Systems interaction and single failure criterion

International Nuclear Information System (INIS)

1981-01-01

This report documents the results of a six-month study to evaluate the ongoing research programs of the U.S. Nuclear Regulatory Commission (NRC) and U.S. commercial nuclear station owners which address the safety significance of systems interaction and the regulatory adequacy of the single failure criterion. The evaluation of system interactions provided is the initial phase of a more detailed study leading to the development and application of methodology for quantifying the relative safety of operating nuclear plants. (Auth.)

Single-time reduction of bethe-salpeter formalism for two-fermion system

International Nuclear Information System (INIS)

Arkhipov, A.A.

1988-01-01

The single-time reduction method proposed in other refs. for the system of two scalar particles is generalized for the case of two-fermion system. A self-consistent procedure of single-time reduction has been constructed both in terms of the Bethe-Salpeter wave function and in terms of the Green's function of two-fermion system. Three-dimensional dynamic equations have been obtained for single-time wave functions and two-time Green's functions of a two-fermion system and the Schroedinger structure of the equations obtained is shown to be a consequence of the causality structure of the local QFT. 32 refs

Electrochemistry and bioelectrochemistry towards the single-molecule level: Theoretical notions and systems

International Nuclear Information System (INIS)

Zhang Jingdong; Chi Qijin; Albrecht, Tim; Kuznetsov, Alexander M.; Grubb, Mikala; Hansen, Allan G.; Wackerbarth, Hainer; Welinder, Anne C.; Ulstrup, Jens

2005-01-01

Surface structures controlled at the nanometer and single-molecule levels, with functions crucially determined by interfacial electron transfer (ET) are broadly reported in recent years, with different kinds of electrochemically controlled nanoscale/single molecule systems. One is the broad class of metallic and semiconductor-based nanoparticles, nano-arrays, nanotubes, and nanopits. Others are based on self-assembled molecular monolayers. The latter extend to bioelectrochemical systems with redox metalloproteins and DNA-based molecules as targets. We overview here some recent achievements in areas of interfacial electrochemical ET systems, mapped to the nanoscale and single-molecule levels. Focus is on both experimental and theoretical studies in our group. Systems addressed are organized monolayers of redox active transition metal complexes, and metalloproteins and metalloenzymes on single-crystal Au(1 1 1)-electrode surfaces. These systems have been investigated by voltammetry, spectroscopy, microcantilever technology, and scanning probe microscopy. A class of Os-complexes has shown suitable as targets for electrochemical in situ scanning tunnelling microscopy (STM), with close to single-molecule scanning tunnelling spectroscopic (STS) features. Mapping of redox metalloproteins from the three major classes, i.e. blue copper proteins, heme proteins, and iron-sulfur proteins, at the monolayer and single-molecule levels have also been achieved. In situ STM and spectroscopy of redox molecules and biomolecules have been supported by new theoretical frames, which extend established theory of interfacial electrochemical ET. The electrochemical nanoscale and single-molecule systems discussed are compared with other recent nanoscale and single-molecule systems with conspicuous device-like properties, particularly unimolecular rectifiers and single-molecule transistors. Both of these show analogies to electrochemical in situ STM features of redox molecules and

Application of agent-based system for bioprocess description and process improvement.

Science.gov (United States)

Gao, Ying; Kipling, Katie; Glassey, Jarka; Willis, Mark; Montague, Gary; Zhou, Yuhong; Titchener-Hooker, Nigel J

2010-01-01

Modeling plays an important role in bioprocess development for design and scale-up. Predictive models can also be used in biopharmaceutical manufacturing to assist decision-making either to maintain process consistency or to identify optimal operating conditions. To predict the whole bioprocess performance, the strong interactions present in a processing sequence must be adequately modeled. Traditionally, bioprocess modeling considers process units separately, which makes it difficult to capture the interactions between units. In this work, a systematic framework is developed to analyze the bioprocesses based on a whole process understanding and considering the interactions between process operations. An agent-based approach is adopted to provide a flexible infrastructure for the necessary integration of process models. This enables the prediction of overall process behavior, which can then be applied during process development or once manufacturing has commenced, in both cases leading to the capacity for fast evaluation of process improvement options. The multi-agent system comprises a process knowledge base, process models, and a group of functional agents. In this system, agent components co-operate with each other in performing their tasks. These include the description of the whole process behavior, evaluating process operating conditions, monitoring of the operating processes, predicting critical process performance, and providing guidance to decision-making when coping with process deviations. During process development, the system can be used to evaluate the design space for process operation. During manufacture, the system can be applied to identify abnormal process operation events and then to provide suggestions as to how best to cope with the deviations. In all cases, the function of the system is to ensure an efficient manufacturing process. The implementation of the agent-based approach is illustrated via selected application scenarios, which

48 CFR 214.202-5 - Descriptive literature.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Descriptive literature. 214.202-5 Section 214.202-5 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS... 214.202-5 Descriptive literature. (c) Requirements of invitation for bids. When brand name or equal...

Background and system description of the Mod 1 wind turbine generator

Science.gov (United States)

Ernst, E. H.

1978-01-01

The Mod-1 wind turbine considered is a large utility-class machine, operating in the high wind regime, which has the potential for generation of utility grade power at costs competitive with other alternative energy sources. A Mod-1 wind turbine generator (WTG) description is presented, taking into account the two variable-pitch steel blades of the rotor, the drive train, power generation/control, the Nacelle structure, and the yaw drive. The major surface elements of the WTG are the ground enclosure, the back-up battery system, the step-up transformer, elements of the data system, cabling, area lighting, and tower foundation. The final system weight (rotor, Nacelle, and tower) is expected to be about 650,000 pounds. The WTG will be capable of delivering 1800 kW to the utility grid in a wind-speed above 25 mph.

Some issues linked to the description of systems in strong interaction

International Nuclear Information System (INIS)

Theussl, L.

2001-06-01

In the first part of this work we have dealt with some issues that are relevant in the area of nucleonic resonances within different constituent quark models. In this context we have concentrated on the theoretical description of Pi and Nu decays for N and Delta resonances. The results obtained point to the necessity of a more microscopic description of the dynamics which is at the same time responsible for the binding of quarks inside baryons and the decay of the latter ones. In the second part we have contributed to the study of crossed two-boson exchanges in the Bethe-Salpeter equation as well as to the investigation of different three-dimensional approaches that follow from the Bethe-Salpeter equation in a certain non-relativistic reduction scheme. These one include in particular an equation whose interaction depends on the total energy of the system. It was shown that such an equation is able to account for a certain number of properties of Bethe-Salpeter equation, in particular, that there also arise abnormal solutions in such an approach. (author)

Single-Chip Computers With Microelectromechanical Systems-Based Magnetic Memory

NARCIS (Netherlands)

Carley, L. Richard; Bain, James A.; Fedder, Gary K.; Greve, David W.; Guillou, David F.; Lu, Michael S.C.; Mukherjee, Tamal; Santhanam, Suresh; Abelmann, Leon; Min, Seungook

This article describes an approach for implementing a complete computer system (CPU, RAM, I/O, and nonvolatile mass memory) on a single integrated-circuit substrate (a chip)—hence, the name "single-chip computer." The approach presented combines advances in the field of microelectromechanical

Computer system design description for SY-101 hydrogen mitigation test project data acquisition and control system (DACS-1). Revision 1

International Nuclear Information System (INIS)

Truitt, R.W.

1994-01-01

This document provides descriptions of components and tasks that are involved in the computer system for the data acquisition and control of the mitigation tests conducted on waste tank SY-101 at the Hanford Nuclear Reservation. The system was designed and implemented by Los alamos National Laboratory and supplied to Westinghouse Hanford Company. The computers (both personal computers and specialized data-taking computers) and the software programs of the system will hereafter collectively be referred to as the DACS (Data Acquisition and Control System)

Spent nuclear fuel project cold vacuum drying facility tempered water and tempered water cooling system design description

International Nuclear Information System (INIS)

IRWIN, J.J.

1998-01-01

This document provides the System Design Description (SDD) for the Cold Vacuum Drying Facility (CVDF) Tempered Water (TW) and Tempered Water Cooling (TWC) System . The SDD was developed in conjunction with HNF-SD-SNF-SAR-002, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998), The HNF-SD-SNF-DRD-O02, 1998, Cold Vacuum Drying Facility Design Requirements, and the CVDF Design Summary Report. The SDD contains general descriptions of the TW and TWC equipment, the system functions, requirements and interfaces. The SDD provides references for design and fabrication details, operation sequences and maintenance. This SOD has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved

Stopping single photons in one-dimensional circuit quantum electrodynamics systems

International Nuclear Information System (INIS)

Shen, J.-T.; Povinelli, M. L.; Sandhu, Sunil; Fan Shanhui

2007-01-01

We propose a mechanism to stop and time reverse single photons in one-dimensional circuit quantum electrodynamics systems. As a concrete example, we exploit the large tunability of the superconducting charge quantum bit (charge qubit) to predict one-photon transport properties in multiple-qubit systems with dynamically controlled transition frequencies. In particular, two qubits coupled to a waveguide give rise to a single-photon transmission line shape that is analogous to electromagnetically induced transparency in atomic systems. Furthermore, by cascading double-qubit structures to form an array and dynamically controlling the qubit transition frequencies, a single photon can be stopped, stored, and time reversed. With a properly designed array, two photons can be stopped and stored in the system at the same time. Moreover, the unit cell of the array can be designed to be of deep subwavelength scale, miniaturizing the circuit

48 CFR 14.202-5 - Descriptive literature.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Descriptive literature. 14... CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.202-5 Descriptive literature. (a) Policy. Contracting officers must not require bidders to furnish descriptive literature unless it is...

48 CFR 514.202-5 - Descriptive literature.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Descriptive literature... CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 514.202-5 Descriptive literature... FAR 52.211-6 satisfies the requirement for descriptive literature. [74 FR 47739, Sept. 17, 2009] ...

Description of an XRF system for multielemental analysis

Energy Technology Data Exchange (ETDEWEB)

Wielopolski, L.; Zhang, R.; Cohn, S.H.

1986-01-01

An X-ray fluorescence (XRF) system which uses radioisotopes in an orthogonal configuration between the source, sample, and detector is described. The advantage of such a system is that for large (bulk) samples or for in vivo measurements the background due to Compton scattering in the sample is minimized. High reproducibility for nonuniform samples is obtained by reducing the sample size and thus the effects of non-uniformity in the spatial response of such a system. Germane to any accurate analytical method is the use of proper mathematical algorithms for data evaluation. The problem is acute, in particular, when photopeaks with low counting statistics are to be analyzed. In the case of a single photopeak on flat, background optimal energy window size, which maximizes the signal-to-noise ratio, for trapezoidal intergration is described. The sensitivity and minimum detection limit at different energies together with background considerations are discussed. 13 refs., 8 figs., 2 tabs.

Description of an XRF system for multielemental analysis

International Nuclear Information System (INIS)

Wielopolski, L.; Zhang, R.; Cohn, S.H.

1986-01-01

An X-ray fluorescence (XRF) system which uses radioisotopes in an orthogonal configuration between the source, sample, and detector is described. The advantage of such a system is that for large (bulk) samples or for in vivo measurements the background due to Compton scattering in the sample is minimized. High reproducibility for nonuniform samples is obtained by reducing the sample size and thus the effects of non-uniformity in the spatial response of such a system. Germane to any accurate analytical method is the use of proper mathematical algorithms for data evaluation. The problem is acute, in particular, when photopeaks with low counting statistics are to be analyzed. In the case of a single photopeak on flat, background optimal energy window size, which maximizes the signal-to-noise ratio, for trapezoidal intergration is described. The sensitivity and minimum detection limit at different energies together with background considerations are discussed. 13 refs., 8 figs., 2 tabs

Single-cell technologies to study the immune system.

Science.gov (United States)

Proserpio, Valentina; Mahata, Bidesh

2016-02-01

The immune system is composed of a variety of cells that act in a coordinated fashion to protect the organism against a multitude of different pathogens. The great variability of existing pathogens corresponds to a similar high heterogeneity of the immune cells. The study of individual immune cells, the fundamental unit of immunity, has recently transformed from a qualitative microscopic imaging to a nearly complete quantitative transcriptomic analysis. This shift has been driven by the rapid development of multiple single-cell technologies. These new advances are expected to boost the detection of less frequent cell types and transient or intermediate cell states. They will highlight the individuality of each single cell and greatly expand the resolution of current available classifications and differentiation trajectories. In this review we discuss the recent advancement and application of single-cell technologies, their limitations and future applications to study the immune system. © 2015 The Authors. Immunology Published by John Wiley & Sons Ltd.

Uniform description and access to Knowledge Organization Systems with BARTOC and JSKOS

OpenAIRE

Voß, Jakob; Ledl, Andreas; Balakrishnan, Uma

2016-01-01

The Basel Register of Thesauri, Ontologies & Classifications (BARTOC) provides information about a large number of Knowledge Organization Systems (KOS) such as classifications, thesauri, authority files etc. To further improve availability and usefulness of both the description and content of KOS, they are mapped to the uniform JSKOS data format being developed in project coli-conc. Specification of a corresponding JSKOS-API will allow users to directly browse and search in KOS from any place.

Low Voltage Ride-Through Capability of a Single-Stage Single-Phase Photovoltaic System Connected to the Low-Voltage Grid

DEFF Research Database (Denmark)

Yang, Yongheng; Blaabjerg, Frede

2013-01-01

The progressively growing of single-phase photovoltaic (PV) systems makes the Distribution System Operators (DSO) to update or revise the existing grid codes in order to guarantee the availability, quality and reliability of the electrical system. It is expected that the future PV systems connected...... to the low-voltage grid will be more active with functionalities of low voltage ride-through (LVRT) and the grid support capability, which is not the case today. In this paper, the operation principle is demonstrated for a single-phase grid-connected PV system in low voltage ride through operation in order...... to map future challenges. The system is verified by simulations and experiments. Test results show that the proposed power control method is effective and the single-phase PV inverters connected to low-voltage networks are ready to provide grid support and ride-through voltage fault capability...

Surface system Forsmark. Site descriptive modelling SDM-Site Forsmark

International Nuclear Information System (INIS)

Lindborg, Tobias

2008-12-01

SKB has undertaken site characterization of two different areas, Forsmark and Laxemar-Simpevarp, in order to find a suitable location for a geological repository for spent nuclear fuel. This report focuses on the site descriptive modelling of the surface system at Forsmark. The characterization of the surface system at the site was primarily made by identifying and describing important properties in different parts of the surface system, properties concerning e.g. hydrology and climate, Quaternary deposits and soils, hydrochemistry, vegetation, ecosystem functions, but also current and historical land use. The report presents available input data, methodology for data evaluation and modelling, and resulting models for each of the different disciplines. Results from the modelling of the surface system are also integrated with results from modelling of the deep bedrock system. The Forsmark site is located within the municipality of Oesthammar, about 120 km north of Stockholm. The investigated area is located along the shoreline of Oeregrundsgrepen, a funnel-shaped bay of the Baltic Sea. The area is characterized by small-scale topographic variations and is almost entirely located at altitudes lower than 20 metres above sea level. The Quaternary deposits in the area are dominated by till, characterized by a rich content of calcite which was transported by the glacier ice to the area from the sedimentary bedrock of Gaevlebukten about 100 km north of Forsmark. As a result, the surface waters and shallow groundwater at Forsmark are characterized by high pH values and high concentrations of certain major constituents, especially calcium and bicarbonate. The annual precipitation and runoff are 560 and 150 mm, respectively. The lakes are small and shallow, with mean and maximum depths ranging from approximately 0.1 to 1 m and 0.4 to 2 m. Sea water flows into the most low-lying lakes during events giving rise to very high sea levels. Wetlands are frequent and cover 25 to 35

Heavy ion microbeam system for study of single event effects

International Nuclear Information System (INIS)

Kamiya, Tomihiro; Utsunomiya, Nobuhiro; Minehara, Eiichi; Tanaka, Ryuichi; Ohmura, Miyoshi; Kohno, Kazuhiro; Iwamoto, Eiji.

1992-01-01

A high-energy heavy ion microbeam system has been developed and installed on a beam line of a 3 MV tandem electrostatic accelerator mainly for analysis of basic mechanism of single event upset (SEU) of semiconductor devices in spacecraft. The SEU is now the most serious problem for highly reliable spacecraft electronics system with long space mission. However, the mechanism has not been understood on the basis of microscopic process of SEU. The SEU phenomena depends not only upon hitting particles, but also upon the hit position on the microcircuit. To observe the transient charge pulse from a SEU, a single ion particle must hit exactly the desired position of the microcircuit. Such an experiment requires the microbeam spot size within 1 μm, the beam positioning accuracy within ±1 μm, and single ion hitting. The microbeam system has been designed to meet the above technical requirements. The system is equipped with two lens systems: one to control the target beam current in a wide range down to extremely low current without any change of the beam optics, and the other to focus heavy ion beams within a spot size of 1 μm. The final goal is to hit a microscopic target area with a single 15 MeV nickel ion. The beam spot size has been evaluated by Gaussian fitting of secondary electron profiles with microbeam scanning across the fine Cu mesh. The single ion detection has been also tested to generate a trigger signal for closing beam shutter to prevent further hits. This paper outlines the new microbeam system and describes methods to realize these techniques. (author)

Interrelations between different canonical descriptions of dissipative systems

International Nuclear Information System (INIS)

Schuch, D; Guerrero, J; López-Ruiz, F F; Aldaya, V

2015-01-01

There are many approaches for the description of dissipative systems coupled to some kind of environment. This environment can be described in different ways; only effective models are being considered here. In the Bateman model, the environment is represented by one additional degree of freedom and the corresponding momentum. In two other canonical approaches, no environmental degree of freedom appears explicitly, but the canonical variables are connected with the physical ones via non-canonical transformations. The link between the Bateman approach and those without additional variables is achieved via comparison with a canonical approach using expanding coordinates, as, in this case, both Hamiltonians are constants of motion. This leads to constraints that allow for the elimination of the additional degree of freedom in the Bateman approach. These constraints are not unique. Several choices are studied explicitly, and the consequences for the physical interpretation of the additional variable in the Bateman model are discussed. (paper)

Interrelations between different canonical descriptions of dissipative systems

Science.gov (United States)

Schuch, D.; Guerrero, J.; López-Ruiz, F. F.; Aldaya, V.

2015-04-01

There are many approaches for the description of dissipative systems coupled to some kind of environment. This environment can be described in different ways; only effective models are being considered here. In the Bateman model, the environment is represented by one additional degree of freedom and the corresponding momentum. In two other canonical approaches, no environmental degree of freedom appears explicitly, but the canonical variables are connected with the physical ones via non-canonical transformations. The link between the Bateman approach and those without additional variables is achieved via comparison with a canonical approach using expanding coordinates, as, in this case, both Hamiltonians are constants of motion. This leads to constraints that allow for the elimination of the additional degree of freedom in the Bateman approach. These constraints are not unique. Several choices are studied explicitly, and the consequences for the physical interpretation of the additional variable in the Bateman model are discussed.

New Approach for Description of Sorption and Swelling phenomena in Liquid + Polymer Membrane Systems.

Czech Academy of Sciences Publication Activity Database

Randová, A.; Bartovská, L.; Hovorka, Š.; Bartovský, T.; Izák, Pavel; Kárászová, Magda; Vopička, O.; Lindnerová, V.

2017-01-01

Roč. 179, MAY (2017), s. 475-485 ISSN 1383-5866 R&D Projects: GA MŠk(CZ) LD14094 Institutional support: RVO:67985858 Keywords : description of sorption * polymer membranes systems * new method Subject RIV: CI - Industrial Chemistry, Chemical Engineering OBOR OECD: Chemical process engineering Impact factor: 3.359, year: 2016

Single-chip serial channel enhances multi-processor systems

Energy Technology Data Exchange (ETDEWEB)

Millar, J.

1982-01-01

In this paper multiprocessor systems are described and explained. The impact that VLSI advancements are having on multiprocessor design is pointed out. The TMS 7041 single-chip microcomputer is described briefly, highlighting its multiprocessor communication capability. And finally, a typical multiprocessor system is shown, implementing the TMS 7041.

A self-description data framework for Tokamak control system design

Energy Technology Data Exchange (ETDEWEB)

Zhang, Ming; Zhang, Jing [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Zheng, Wei, E-mail: zhengwei@hust.edu.cn [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Hu, Feiran; Zhuang, Ge [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China)

2015-10-15

Highlights: • The SDD framework can be applied to different Tokamak devices. • We explain how configuration settings of control systems are described in SDD models, namely components and connections. • Evolving SDD models are stored in a dynamic schema database. • The SDD editor supports plug-and-play SDD models. - Abstract: A Tokamak device consists of numerous control systems, which need to be integrated. CODAC (Control, Data Access and Communication) system requires the configuration settings of these control systems to carry out the integration smoothly. SDD (Self-description data) is designed to describe the static configuration of control systems. ITER CODAC group has released an SDD software package for control system designers to manage the static configuration, but it is specific for ITER plant control systems. Following the idea of ITER SDD, we developed a flexible and scalable SDD framework to develop SDD software for J-TEXT and other sophisticated devices. The SDD framework describes the configuration settings of various control systems, including physical and logical elements and their relation information, in SDD models which are classified into Components and Connections. The framework is composed of three layers: the MongoDB database, an open-source, dynamic schema, NoSQL (Not Only SQL) database; the SDD service, which maps SDD models to MongoDB and handles the transaction and business logic; the SDD applications, which can be used to create and maintain SDD information, and generate various kinds of output using the stored SDD information.

A self-description data framework for Tokamak control system design

International Nuclear Information System (INIS)

Zhang, Ming; Zhang, Jing; Zheng, Wei; Hu, Feiran; Zhuang, Ge

2015-01-01

Highlights: • The SDD framework can be applied to different Tokamak devices. • We explain how configuration settings of control systems are described in SDD models, namely components and connections. • Evolving SDD models are stored in a dynamic schema database. • The SDD editor supports plug-and-play SDD models. - Abstract: A Tokamak device consists of numerous control systems, which need to be integrated. CODAC (Control, Data Access and Communication) system requires the configuration settings of these control systems to carry out the integration smoothly. SDD (Self-description data) is designed to describe the static configuration of control systems. ITER CODAC group has released an SDD software package for control system designers to manage the static configuration, but it is specific for ITER plant control systems. Following the idea of ITER SDD, we developed a flexible and scalable SDD framework to develop SDD software for J-TEXT and other sophisticated devices. The SDD framework describes the configuration settings of various control systems, including physical and logical elements and their relation information, in SDD models which are classified into Components and Connections. The framework is composed of three layers: the MongoDB database, an open-source, dynamic schema, NoSQL (Not Only SQL) database; the SDD service, which maps SDD models to MongoDB and handles the transaction and business logic; the SDD applications, which can be used to create and maintain SDD information, and generate various kinds of output using the stored SDD information.

Robotic Laparoendoscopic Single-site Retroperitioneal Renal Surgery: Initial Investigation of a Purpose-built Single-port Surgical System.

Science.gov (United States)

Maurice, Matthew J; Ramirez, Daniel; Kaouk, Jihad H

2017-04-01

Robotic single-site retroperitoneal renal surgery has the potential to minimize the morbidity of standard transperitoneal and multiport approaches. Traditionally, technological limitations of non-purpose-built robotic platforms have hindered the application of this approach. To assess the feasibility of retroperitoneal renal surgery using a new purpose-built robotic single-port surgical system. This was a preclinical study using three male cadavers to assess the feasibility of the da Vinci SP1098 surgical system for robotic laparoendoscopic single-site (R-LESS) retroperitoneal renal surgery. We used the SP1098 to perform retroperitoneal R-LESS radical nephrectomy (n=1) and bilateral partial nephrectomy (n=4) on the anterior and posterior surfaces of the kidney. Improvements unique to this system include enhanced optics and intelligent instrument arm control. Access was obtained 2cm anterior and inferior to the tip of the 12th rib using a novel 2.5-cm robotic single-port system that accommodates three double-jointed articulating robotic instruments, an articulating camera, and an assistant port. The primary outcome was the technical feasibility of the procedures, as measured by the need for conversion to standard techniques, intraoperative complications, and operative times. All cases were completed without the need for conversion. There were no intraoperative complications. The operative time was 100min for radical nephrectomy, and the mean operative time was 91.8±18.5min for partial nephrectomy. Limitations include the preclinical model, the small sample size, and the lack of a control group. Single-site retroperitoneal renal surgery is feasible using the latest-generation SP1098 robotic platform. While the potential of the SP1098 appears promising, further study is needed for clinical evaluation of this investigational technology. In an experimental model, we used a new robotic system to successfully perform major surgery on the kidney through a single small

Detailed description of a state system for accounting for and control of nuclear material at the state level

International Nuclear Information System (INIS)

Jones, R.J.

1985-02-01

The purpose of this document is to provide a detailed description of the technical elements of a system for the accounting for and control of nuclear material at the State Authority level which can be used by a state in the establishment of a national system for nuclear material accounting and control. It is expected that a state system designed along the lines described also will assist the IAEA in carrying out its safeguards responsibilities. The scope of this document is limited to descriptions of the technical elements of a state level system concerned with Laws and Regulations, the Information System, and the Establishment of Requirements for Nuclear Material Accounting and Control. The discussion shows the relationship of these technical elements at the state level to the principal elements of an SSAC at the facility levels

Components of formalized description of selecting tools for ensuring stability of banking system

Directory of Open Access Journals (Sweden)

N.P. Pogorelenko

2015-09-01

Full Text Available A banking system is one of the key elements of a financial market of any country. Effectiveness and functional orientation of a banking system provide continuous and targeted financial resources flowing between different sectors of economy and this allows to perform economic activities of various entities. Thus, a banking system plays an essential role in the formation of market relations. A question of stable functioning of a banking system can be defined as a key one. The basic task is to improve the management of a banking system by achieving its stability. The disclosure of formalized description of the definition of tools to influence the selection procedure for ensuring stability of a banking system should be determined as the primary objective. For reaching the goal a comparative study has been introduced and generalized concerning the concept definition of «banking system» and the ideology of its management according to the circumstances and factors of influence. The combination of individual components is to determine the instruments of influence on the banking system activity in the form of chain ties. On the base of the analysis carried out the article grounds the necessity of the generalized use of formalized description of the procedures for selecting instruments for ensuring stability of a banking system. For the purpose of this procedure the author has also grounded, determined and disclosed some of its components. To implement the relevant qualitative phase of formalization the author has proposed the use of chain patterns, and to quantify the individual parameters of such a procedure the methodology of border stochastic analysis has been offered. As a scientific novelty of the present research it is necessary to note the qualitative and quantitative phases for formal presentation of describing procedures for the selection of tools to ensure banking system stability as well as the introduction of chain schemes for the

A single-chip computer analysis system for liquid fluorescence

International Nuclear Information System (INIS)

Zhang Yongming; Wu Ruisheng; Li Bin

1998-01-01

The single-chip computer analysis system for liquid fluorescence is an intelligent analytic instrument, which is based on the principle that the liquid containing hydrocarbons can give out several characteristic fluorescences when irradiated by strong light. Besides a single-chip computer, the system makes use of the keyboard and the calculation and printing functions of a CASIO printing calculator. It combines optics, mechanism and electronics into one, and is small, light and practical, so it can be used for surface water sample analysis in oil field and impurity analysis of other materials

Non-linear phenomena in electronic systems consisting of coupled single-electron oscillators

International Nuclear Information System (INIS)

Kikombo, Andrew Kilinga; Hirose, Tetsuya; Asai, Tetsuya; Amemiya, Yoshihito

2008-01-01

This paper describes non-linear dynamics of electronic systems consisting of single-electron oscillators. A single-electron oscillator is a circuit made up of a tunneling junction and a resistor, and produces simple relaxation oscillation. Coupled with another, single electron oscillators exhibit complex behavior described by a combination of continuous differential equations and discrete difference equations. Computer simulation shows that a double-oscillator system consisting of two coupled oscillators produces multi-periodic oscillation with a single attractor, and that a quadruple-oscillator system consisting of four oscillators also produces multi-periodic oscillation but has a number of possible attractors and takes one of them determined by initial conditions

Microscopic description of pair transfer between two superfluid Fermi systems: Combining phase-space averaging and combinatorial techniques

Science.gov (United States)

Regnier, David; Lacroix, Denis; Scamps, Guillaume; Hashimoto, Yukio

2018-03-01

In a mean-field description of superfluidity, particle number and gauge angle are treated as quasiclassical conjugated variables. This level of description was recently used to describe nuclear reactions around the Coulomb barrier. Important effects of the relative gauge angle between two identical superfluid nuclei (symmetric collisions) on transfer probabilities and fusion barrier have been uncovered. A theory making contact with experiments should at least average over different initial relative gauge-angles. In the present work, we propose a new approach to obtain the multiple pair transfer probabilities between superfluid systems. This method, called phase-space combinatorial (PSC) technique, relies both on phase-space averaging and combinatorial arguments to infer the full pair transfer probability distribution at the cost of multiple mean-field calculations only. After benchmarking this approach in a schematic model, we apply it to the collision 20O+20O at various energies below the Coulomb barrier. The predictions for one pair transfer are similar to results obtained with an approximated projection method, whereas significant differences are found for two pairs transfer. Finally, we investigated the applicability of the PSC method to the contact between nonidentical superfluid systems. A generalization of the method is proposed and applied to the schematic model showing that the pair transfer probabilities are reasonably reproduced. The applicability of the PSC method to asymmetric nuclear collisions is investigated for the 14O+20O collision and it turns out that unrealistically small single- and multiple pair transfer probabilities are obtained. This is explained by the fact that relative gauge angle play in this case a minor role in the particle transfer process compared to other mechanisms, such as equilibration of the charge/mass ratio. We conclude that the best ground for probing gauge-angle effects in nuclear reaction and/or for applying the proposed

Single Bit Radar Systems for Digital Integration

OpenAIRE

Bjørndal, Øystein

2017-01-01

Small, low cost, radar systems have exciting applications in monitoring and imaging for the industrial, healthcare and Internet of Things (IoT) sectors. We here explore, and show the feasibility of, several single bit square wave radar architectures; that benefits from the continuous improvement in digital technologies for system-on-chip digital integration. By analysis, simulation and measurements we explore novel and harmonic-rich continuous wave (CW), stepped-frequency CW (SFCW) and freque...

The verbal facilitation effect: re-reading person descriptions as a system variable to improve identification performance.

Science.gov (United States)

Sporer, Siegfried L; Kaminski, Kristina S; Davids, Maike C; McQuiston, Dawn

2016-11-01

When witnesses report a crime, police usually ask for a description of the perpetrator. Several studies suggested that verbalising faces leads to a detriment in identification performance (verbal overshadowing effect [VOE]) but the effect has been difficult to replicate. Here, we sought to reverse the VOE by inducing context reinstatement as a system variable through re-reading one's own description before an identification task. Participants (N = 208) watched a video film and were then dismissed (control group), only described the perpetrator, or described and later re-read their own descriptions before identification in either target-present or target-absent lineups after a 2-day or a 5-week delay. Identification accuracy was significantly higher after re-reading (85.0%) than in the no description control group (62.5%) irrespective of target presence. Data were internally replicated using a second target and corroborated by several small meta-analyses. Identification accuracy was related to description quality. Moreover, there was a tendency towards a verbal facilitation effect (VFE) rather than a VOE. Receiver operating characteristic (ROC) curve analyses confirm that our findings are not due to a shift in response bias but truly reflect improvement of recognition performance. Differences in the ecological validity of study paradigms are discussed.

Consistent Probabilistic Description of the Neutral Kaon System: Novel Observable Effects

CERN Document Server

Bernabeu, J.; Villanueva-Perez, P.

2013-01-01

The neutral Kaon system has both CP violation in the mass matrix and a non-vanishing lifetime difference in the width matrix. This leads to an effective Hamiltonian which is not a normal operator, with incompatible (non-commuting) masses and widths. In the Weisskopf-Wigner Approach (WWA), by diagonalizing the entire Hamiltonian, the unphysical non-orthogonal "stationary" states $K_{L,S}$ are obtained. These states have complex eigenvalues whose real (imaginary) part does not coincide with the eigenvalues of the mass (width) matrix. In this work we describe the system as an open Lindblad-type quantum mechanical system due to Kaon decays. This approach, in terms of density matrices for initial and final states, provides a consistent probabilistic description, avoiding the standard problems because the width matrix becomes a composite operator not included in the Hamiltonian. We consider the dominant-decay channel to two pions, so that one of the Kaon states with definite lifetime becomes stable. This new approa...

Cold Vacuum Dryer (CVD) Facility Fire Protection System Design Description (SYS 24)

Energy Technology Data Exchange (ETDEWEB)

SINGH, G.

2000-10-17

This system design description (SDD) addresses the Cold Vacuum Drying (CVD) Facility fire protection system (FPS). The primary features of the FPS for the CVD are a fire alarm and detection system, automatic sprinklers, and fire hydrants. The FPS also includes fire extinguishers located throughout the facility and fire hydrants to assist in manual firefighting efforts. In addition, a fire barrier separates the operations support (administrative) area from the process bays and process bay support areas. Administrative controls to limit combustible materials have been established and are a part of the overall fire protection program. The FPS is augmented by assistance from the Hanford Fire Department (HED) and by interface systems including service water, electrical power, drains, instrumentation and controls. This SDD, when used in conjunction with the other elements of the definitive design package, provides a complete picture of the FPS for the CVD Facility.

MPEG-7-based description infrastructure for an audiovisual content analysis and retrieval system

Science.gov (United States)

Bailer, Werner; Schallauer, Peter; Hausenblas, Michael; Thallinger, Georg

2005-01-01

We present a case study of establishing a description infrastructure for an audiovisual content-analysis and retrieval system. The description infrastructure consists of an internal metadata model and access tool for using it. Based on an analysis of requirements, we have selected, out of a set of candidates, MPEG-7 as the basis of our metadata model. The openness and generality of MPEG-7 allow using it in broad range of applications, but increase complexity and hinder interoperability. Profiling has been proposed as a solution, with the focus on selecting and constraining description tools. Semantic constraints are currently only described in textual form. Conformance in terms of semantics can thus not be evaluated automatically and mappings between different profiles can only be defined manually. As a solution, we propose an approach to formalize the semantic constraints of an MPEG-7 profile using a formal vocabulary expressed in OWL, which allows automated processing of semantic constraints. We have defined the Detailed Audiovisual Profile as the profile to be used in our metadata model and we show how some of the semantic constraints of this profile can be formulated using ontologies. To work practically with the metadata model, we have implemented a MPEG-7 library and a client/server document access infrastructure.

A Unified Description of Structural Levels in Biomolecules.

Science.gov (United States)

Macarulla, Alberto; And Others

1990-01-01

A single, didactic criterion for the description of all biological macromolecules is proposed. This criterion is applicable to globular, fibrous or mixed proteins, as well as to nucleic acids and lipids or polysaccharides. Specific examples are given for all except lipids and polysaccarides. (KR)

Delay-induced wave instabilities in single-species reaction-diffusion systems

Science.gov (United States)

Otto, Andereas; Wang, Jian; Radons, Günter

2017-11-01

The Turing (wave) instability is only possible in reaction-diffusion systems with more than one (two) components. Motivated by the fact that a time delay increases the dimension of a system, we investigate the presence of diffusion-driven instabilities in single-species reaction-diffusion systems with delay. The stability of arbitrary one-component systems with a single discrete delay, with distributed delay, or with a variable delay is systematically analyzed. We show that a wave instability can appear from an equilibrium of single-species reaction-diffusion systems with fluctuating or distributed delay, which is not possible in similar systems with constant discrete delay or without delay. More precisely, we show by basic analytic arguments and by numerical simulations that fast asymmetric delay fluctuations or asymmetrically distributed delays can lead to wave instabilities in these systems. Examples, for the resulting traveling waves are shown for a Fisher-KPP equation with distributed delay in the reaction term. In addition, we have studied diffusion-induced instabilities from homogeneous periodic orbits in the same systems with variable delay, where the homogeneous periodic orbits are attracting resonant periodic solutions of the system without diffusion, i.e., periodic orbits of the Hutchinson equation with time-varying delay. If diffusion is introduced, standing waves can emerge whose temporal period is equal to the period of the variable delay.

Retrievable surface storage facility conceptual system design description

Energy Technology Data Exchange (ETDEWEB)

1977-03-01

The studies evaluated several potentially attractive methods for processing and retrievably storing high-level radioactive waste after delivery to the Federal repository. These studies indicated that several systems could be engineered to safely store the waste, but that the simplest and most attractive concept from a technical standpoint would be to store the waste in a sealed stainless steel canister enclosed in a 2 in. thick carbon steel cask which in turn would be inserted into a reinforced concrete gamma-neutron shield, which would also provide the necessary air-cooling through an air annulus between the cask and the shield. This concept best satisfies the requirements for safety, long-term exposure to natural phenomena, low capital and operating costs, retrievability, amenability to incremental development, and acceptably small environmental impact. This document assumes that the reference site would be on ERDA's Hanford reservation. This document is a Conceptual System Design Description of the facilities which could satisfy all of the functional requirements within the established basic design criteria. The Retrievable Surface Storage Facility (RSSF) is planned with the capacity to process and store the waste received in either a calcine or glass/ceramic form. The RSSF planning is based on a modular development program in which the modular increments are constructed at rates matching projected waste receipts.

Retrievable surface storage facility conceptual system design description

International Nuclear Information System (INIS)

1977-03-01

The studies evaluated several potentially attractive methods for processing and retrievably storing high-level radioactive waste after delivery to the Federal repository. These studies indicated that several systems could be engineered to safely store the waste, but that the simplest and most attractive concept from a technical standpoint would be to store the waste in a sealed stainless steel canister enclosed in a 2 in. thick carbon steel cask which in turn would be inserted into a reinforced concrete gamma-neutron shield, which would also provide the necessary air-cooling through an air annulus between the cask and the shield. This concept best satisfies the requirements for safety, long-term exposure to natural phenomena, low capital and operating costs, retrievability, amenability to incremental development, and acceptably small environmental impact. This document assumes that the reference site would be on ERDA's Hanford reservation. This document is a Conceptual System Design Description of the facilities which could satisfy all of the functional requirements within the established basic design criteria. The Retrievable Surface Storage Facility (RSSF) is planned with the capacity to process and store the waste received in either a calcine or glass/ceramic form. The RSSF planning is based on a modular development program in which the modular increments are constructed at rates matching projected waste receipts

General description of few-body break-up processes at threshold

International Nuclear Information System (INIS)

Barrachina, R.O.

2004-01-01

Full text: In this communication we present a general description of the behavior of fragmentation processes near threshold by analyzing the break-up into two, three and N bodies in steps of increasing complexity. In particular, we describe the effects produced by an N-body threshold behavior in N+1 body break-up processes, as it occurs in situations where one of the fragments acquires almost all the excess energy of the system. Furthermore, we relate the appearance of cusps and discontinuities in single-particle multiply differential cross sections to the threshold behavior of the remaining particles, and apply these ideas to different systems from atomic, molecular and nuclear collision physics. We finally show that, even though the study of ultracold collisions represents the direct way of gathering information on a break-up system near threshold, the analysis of high-energy collisions provides an alternative, and sometimes advantageous, approach

Synchronization in single-phase grid-connected photovoltaic systems under grid faults

DEFF Research Database (Denmark)

Yang, Yongheng; Blaabjerg, Frede

2012-01-01

The highly increasing penetration of single-phase photovoltaic (PV) systems pushes the grid requirements related to the integration of PV power systems to be updated. These upcoming regulations are expected to direct the grid-connected renewable generators to support the grid operation and stabil......The highly increasing penetration of single-phase photovoltaic (PV) systems pushes the grid requirements related to the integration of PV power systems to be updated. These upcoming regulations are expected to direct the grid-connected renewable generators to support the grid operation...

Solar Pilot Plant, Phase I. Preliminary design report. Volume II. System description and system analysis. CDRL item 2

Energy Technology Data Exchange (ETDEWEB)

None

1977-05-01

Honeywell conducted a parametric analysis of the 10-MW(e) solar pilot plant requirements and expected performance and established an optimum system design. The main analytical simulation tools were the optical (ray trace) and the dynamic simulation models. These are described in detail in Books 2 and 3 of this volume under separate cover. In making design decisions, available performance and cost data were used to provide a design reflecting the overall requirements and economics of a commercial-scale plant. This volume contains a description of this analysis/design process and resultant system/subsystem design and performance.

Second law comparison of single effect and double effect vapour absorption refrigeration systems

International Nuclear Information System (INIS)

Gomri, Rabah

2009-01-01

In this paper a comparative study between single effect and double effect absorption refrigeration systems with identical cold output is carried out. Simulation results were used to study the influence of the various operating parameters on the performance coefficient, the thermal loads of the components, exergetic efficiency (rational efficiency) and the total change in exergy of the two systems. It is concluded that the COP of double effect system is approximately twice the COP of single effect system but the exergetic efficiency of double effect system increase slightly compared to the exergetic efficiency of single effect system. It is found that for each condenser and evaporator temperature, there is an optimum generator temperature where the total change in exergy of the single effect and double effect absorption refrigeration systems is minimum. At this point the COP and exergetic efficiency of the systems become maximum. In this study and when the evaporation temperature is varied from 4 deg. C to 10 deg. C, condenser and absorber temperatures are varied from 33 deg. C to 39 deg. C and generator (HPG) temperature is varied from 60 deg. C to 190 deg. C the maximum COP values of the single effect refrigeration systems are in the range of 0.73-0.79 and for double effect refrigeration systems are in the range of 1.22-1.42. The maximum exergetic efficiency values of the single effect refrigeration systems are in the range of 12.5-23.2% and for double effect refrigeration systems are in the range of 14.3-25.1%.

AN ANALYSIS OF STUDENT‘S DESCRIPTIVE TEXT: SYSTEMIC FUNCTIONAL LINGUISTICS PERSPECTIVES

Directory of Open Access Journals (Sweden)

Rizka Maulina Wulandari

2017-12-01

Full Text Available In Indonesia where different languages co-exist, and where English is used as a foreign language, the learners‘ capabilities in writing toward English plays an important role in formulating effective learning method. This descriptive qualitative research aimed to investigate the student‘s errors in writing descriptive text in SFL perspectives. A secondary, yet important, objective of this research is also to design the appropriate pedagogical plans that can be used for junior high school students in Indonesian education based on the result of the research. The results indicated that the student has good control about the schematic structure of descriptive text although many of his idea still uses Indonesian context which make the reader can be confused in understanding his meaning. It can be concluded that there is intervention from L1, that is Indonesian language, while he wrote his descriptive text.. Hence, the study highlighted that cooperative learning could be an option as an appropriate learning method to solve the students problem on writing descriptive text.

A single-system model predicts recognition memory and repetition priming in amnesia.

Science.gov (United States)

Berry, Christopher J; Kessels, Roy P C; Wester, Arie J; Shanks, David R

2014-08-13

We challenge the claim that there are distinct neural systems for explicit and implicit memory by demonstrating that a formal single-system model predicts the pattern of recognition memory (explicit) and repetition priming (implicit) in amnesia. In the current investigation, human participants with amnesia categorized pictures of objects at study and then, at test, identified fragmented versions of studied (old) and nonstudied (new) objects (providing a measure of priming), and made a recognition memory judgment (old vs new) for each object. Numerous results in the amnesic patients were predicted in advance by the single-system model, as follows: (1) deficits in recognition memory and priming were evident relative to a control group; (2) items judged as old were identified at greater levels of fragmentation than items judged new, regardless of whether the items were actually old or new; and (3) the magnitude of the priming effect (the identification advantage for old vs new items) overall was greater than that of items judged new. Model evidence measures also favored the single-system model over two formal multiple-systems models. The findings support the single-system model, which explains the pattern of recognition and priming in amnesia primarily as a reduction in the strength of a single dimension of memory strength, rather than a selective explicit memory system deficit. Copyright © 2014 the authors 0270-6474/14/3410963-12$15.00/0.

Approaches to Quality Risk Management When Using Single-Use Systems in the Manufacture of Biologics.

Science.gov (United States)

Ishii-Watabe, Akiko; Hirose, Akihiko; Katori, Noriko; Hashii, Norikata; Arai, Susumu; Awatsu, Hirotoshi; Eiza, Akira; Hara, Yoshiaki; Hattori, Hideshi; Inoue, Tomomi; Isono, Tetsuya; Iwakura, Masahiro; Kajihara, Daisuke; Kasahara, Nobuo; Matsuda, Hiroyuki; Murakami, Sei; Nakagawa, Taishiro; Okumura, Takehiro; Omasa, Takeshi; Takuma, Shinya; Terashima, Iyo; Tsukahara, Masayoshi; Tsutsui, Maiko; Yano, Takahiro; Kawasaki, Nana

2015-10-01

Biologics manufacturing technology has made great progress in the last decade. One of the most promising new technologies is the single-use system, which has improved the efficiency of biologics manufacturing processes. To ensure safety of biologics when employing such single-use systems in the manufacturing process, various issues need to be considered including possible extractables/leachables and particles arising from the components used in single-use systems. Japanese pharmaceutical manufacturers, together with single-use suppliers, members of the academia and regulatory authorities have discussed the risks of using single-use systems and established control strategies for the quality assurance of biologics. In this study, we describe approaches for quality risk management when employing single-use systems in the manufacturing of biologics. We consider the potential impact of impurities related to single-use components on drug safety and the potential impact of the single-use system on other critical quality attributes as well as the stable supply of biologics. We also suggest a risk-mitigating strategy combining multiple control methods which includes the selection of appropriate single-use components, their inspections upon receipt and before releasing for use and qualification of single-use systems. Communication between suppliers of single-use systems and the users, as well as change controls in the facilities both of suppliers and users, are also important in risk-mitigating strategies. Implementing these control strategies can mitigate the risks attributed to the use of single-use systems. This study will be useful in promoting the development of biologics as well as in ensuring their safety, quality and stable supply.

Benchmarking of Grid Fault Modes in Single-Phase Grid-Connected Photovoltaic Systems

DEFF Research Database (Denmark)

Yang, Yongheng; Blaabjerg, Frede; Zou, Zhixiang

2013-01-01

Pushed by the booming installations of singlephase photovoltaic (PV) systems, the grid demands regarding the integration of PV systems are expected to be modified. Hence, the future PV systems should become more active with functionalities of Low Voltage Ride-Through (LVRT) and grid support...... phase systems under grid faults. The intent of this paper is to present a benchmarking of grid fault modes that might come in future single-phase PV systems. In order to map future challenges, the relevant synchronization and control strategies are discussed. Some faulty modes are studied experimentally...... and provided at the end of this paper. It is concluded that there are extensive control possibilities in single-phase PV systems under grid faults. The Second Order General Integral based PLL technique might be the most promising candidate for future single-phase PV systems because of its fast adaptive...

Project W-211 Initial Tank Retrieval Systems (ITRS) Description of Operations for 241-AZ-102

Energy Technology Data Exchange (ETDEWEB)

BRIGGS, S.R.

2000-02-25

The primary purpose of the Initial Tank Retrieval Systems (ITRS) is to provide systems for retrieval of radioactive wastes stored in underground double-shell tanks (DSTs) for transfer to alternate storage, evaporation, pretreatment or treatment, while concurrently reducing risks associated with safety watch list and other DSTs. This Description of Operation (DOO) defines the control philosophy for the waste retrieval system for Tank 241-AZ-102 (AZ-102). This DOO provides a basis for the detailed design of the Project W-211 Retrieval Control System (RCS) for AZ-102 and also establishes test criteria for the RCS.

Project W-211 Initial Tank Retrieval Systems (ITRS) Description of Operations for 241-AZ-102

International Nuclear Information System (INIS)

BRIGGS, S.R.

2000-01-01

The primary purpose of the Initial Tank Retrieval Systems (ITRS) is to provide systems for retrieval of radioactive wastes stored in underground double-shell tanks (DSTs) for transfer to alternate storage, evaporation, pretreatment or treatment, while concurrently reducing risks associated with safety watch list and other DSTs. This Description of Operation (DOO) defines the control philosophy for the waste retrieval system for Tank 241-AZ-102 (AZ-102). This DOO provides a basis for the detailed design of the Project W-211 Retrieval Control System (RCS) for AZ-102 and also establishes test criteria for the RCS

A performance comparison of single product kanban control systems

Directory of Open Access Journals (Sweden)

Alvin Ang

2015-01-01

Full Text Available This paper presents a simulation experiment comparing the Single Stage, Single Product Base Stock (BS, Traditional Kanban Control System (TKCS and Extended Kanban Control System (EKCS. The results showed that BS incurs the highest cost in all scenarios; while EKCS is found to be effective only in a very niche scenario. TKCS is still a very powerful factory management system to date; and EKCS did not perform exceptionally well. The only time EKCS did outperform TKCS was during low demand arrival rates and low Backorder (Cb and Shortage costs (Cs. That is because during then, it holds no stock. The most important discovery made here is that EKCS becomes TKCS once it has base stock (or dispatched kanbans. The results have also evinced the strength of the pure kanban system, the TKCS over BS. Hence managers using BS should consider upgrading to TKCS to save cost.

Robust fault detection and isolation technique for single-input/single-output closed-loop control systems that exhibit actuator and sensor faults

DEFF Research Database (Denmark)

Izadi-Zamanabadi, Roozbeh; Alavi, S. M. Mahdi; Hayes, M. J.

2008-01-01

An integrated quantitative feedback design and frequency-based fault detection and isolation (FDI) approach is presented for single-input/single-output systems. A novel design methodology, based on shaping the system frequency response, is proposed to generate an appropriate residual signal...

Recommended procedures and methodology of coal description

Science.gov (United States)

Chao, E.C.; Minkin, J.A.; Thompson, C.L.

1983-01-01

This document is the result of a workshop on coal description held for the Branch of Coal Resources of the U.S. Geological Survey in March 1982. It has been prepared to aid and encourage the field-oriented coal scientist to participate directly in petrographic coal-description activities. The objectives and past and current practices of coal description vary widely. These are briefly reviewed and illustrated with examples. Sampling approaches and techniques for collecting columnar samples of fresh coal are also discussed. The recommended procedures and methodology emphasize the fact that obtaining a good megascopic description of a coal bed is much better done in the laboratory with a binocular microscope and under good lighting conditions after the samples have been cut and quickly prepared. For better observation and cross-checking using a petrographic microscope for identification purposes, an in-place polishing procedure (requiring less than 2 min) is routinely used. Methods for using both the petrographic microscope and an automated image analysis system are also included for geologists who have access to such instruments. To describe the material characteristics of a coal bed in terms of microlithotypes or lithotypes, a new nomenclature of (V), (E), (1), (M). (S). (X1). (X2) and so on is used. The microscopic description of the modal composition of a megascopically observed lithologic type is expressed in terms of (VEIM); subscripts are used to denote the volume percentage of each constituent present. To describe a coal-bed profile, semiquantitative data (without microscopic study) and quantitative data (with microscopic study) are presented in ready-to-understand form. The average total composition of any thickness interval or of the entire coal bed can be plotted on a triangular diagram having V, E, and I+ M +S as the apices. The modal composition of any mixed lithologies such as (X1), (X2), and so on can also be plotted on such a triangular ternary diagram

Fluctuating local field method probed for a description of small classical correlated lattices

Science.gov (United States)

Rubtsov, Alexey N.

2018-05-01

Thermal-equilibrated finite classical lattices are considered as a minimal model of the systems showing an interplay between low-energy collective fluctuations and single-site degrees of freedom. Standard local field approach, as well as classical limit of the bosonic DMFT method, do not provide a satisfactory description of Ising and Heisenberg small lattices subjected to an external polarizing field. We show that a dramatic improvement can be achieved within a simple approach, in which the local field appears to be a fluctuating quantity related to the low-energy degree(s) of freedom.

Investigations of Intelligent Solar Heating Systems for Single Family House

DEFF Research Database (Denmark)

Andersen, Elsa; Chen, Ziqian; Fan, Jianhua

2014-01-01

Three differently designed intelligent solar heating systems are investigated experimentally in a test facility. The systems provide all the needed yearly heating demand in single family houses. The systems are based on highly stratified tanks with variable auxiliary heated volumes. The tank is a......, the control strategy of intelligent solar heating systems is investigated and the yearly auxiliary energy use of the systems and the electricity price for supplying the consumers with domestic hot water and space heating are calculated....... systems.The system will be equipped with an intelligent control system where the control of the electrical heating element(s)/heat pump is based on forecasts of the variable electricity price, the heating demand and the solar energy production.By means of numerical models of the systems made in Trnsys......Three differently designed intelligent solar heating systems are investigated experimentally in a test facility. The systems provide all the needed yearly heating demand in single family houses. The systems are based on highly stratified tanks with variable auxiliary heated volumes. The tank...

Space Station Environmental Control/Life Support System engineering

Science.gov (United States)

Miller, C. W.; Heppner, D. B.

1985-01-01

The present paper is concerned with a systems engineering study which has provided an understanding of the overall Space Station ECLSS (Environmental Control and Life Support System). ECLSS/functional partitioning is considered along with function criticality, technology alternatives, a technology description, single thread systems, Space Station architectures, ECLSS distribution, mechanical schematics per space station, and Space Station ECLSS characteristics. Attention is given to trade studies and system synergism. The Space Station functional description had been defined by NASA. The ECLSS will utilize technologies which embody regenerative concepts to minimize the use of expendables.

Single-source mechanical loading system produces biaxial stresses in cylinders

Science.gov (United States)

Flower, J. F.; Stafford, R. L.

1967-01-01

Single-source mechanical loading system proportions axial-to-hoop tension loads applied to cylindrical specimens. The system consists of hydraulic, pneumatic, and lever arrangements which produce biaxial loading ratios.

Torque Measurement at the Single Molecule Level

Science.gov (United States)

Forth, Scott; Sheinin, Maxim Y.; Inman, James; Wang, Michelle D.

2017-01-01

Methods for exerting and measuring forces on single molecules have revolutionized the study of the physics of biology. However, it is often the case that biological processes involve rotation or torque generation, and these parameters have been more difficult to access experimentally. Recent advances in the single molecule field have led to the development of techniques which add the capability of torque measurement. By combining force, displacement, torque, and rotational data, a more comprehensive description of the mechanics of a biomolecule can be achieved. In this review, we highlight a number of biological processes for which torque plays a key mechanical role. We describe the various techniques that have been developed to directly probe the torque experienced by a single molecule, and detail a variety of measurements made to date using these new technologies. We conclude by discussing a number of open questions and propose systems of study which would be well suited for analysis with torsional measurement techniques. PMID:23541162

Voltage controlled nano-injection system for single-cell surgery

Science.gov (United States)

Seger, R. Adam; Actis, Paolo; Penfold, Catherine; Maalouf, Michelle; Vilozny, Boaz; Pourmand, Nader

2015-01-01

Manipulation and analysis of single cells is the next frontier in understanding processes that control the function and fate of cells. Herein we describe a single-cell injection platform based on nanopipettes. The system uses scanning microscopy techniques to detect cell surfaces, and voltage pulses to deliver molecules into individual cells. As a proof of concept, we injected adherent mammalian cells with fluorescent dyes. PMID:22899383

Stable long-time semiclassical description of zero-point energy in high-dimensional molecular systems.

Science.gov (United States)

Garashchuk, Sophya; Rassolov, Vitaly A

2008-07-14

Semiclassical implementation of the quantum trajectory formalism [J. Chem. Phys. 120, 1181 (2004)] is further developed to give a stable long-time description of zero-point energy in anharmonic systems of high dimensionality. The method is based on a numerically cheap linearized quantum force approach; stabilizing terms compensating for the linearization errors are added into the time-evolution equations for the classical and nonclassical components of the momentum operator. The wave function normalization and energy are rigorously conserved. Numerical tests are performed for model systems of up to 40 degrees of freedom.

New apparatus of single particle trap system for aerosol visualization

Science.gov (United States)

Higashi, Hidenori; Fujioka, Tomomi; Endo, Tetsuo; Kitayama, Chiho; Seto, Takafumi; Otani, Yoshio

2014-08-01

Control of transport and deposition of charged aerosol particles is important in various manufacturing processes. Aerosol visualization is an effective method to directly observe light scattering signal from laser-irradiated single aerosol particle trapped in a visualization cell. New single particle trap system triggered by light scattering pulse signal was developed in this study. The performance of the device was evaluated experimentally. Experimental setup consisted of an aerosol generator, a differential mobility analyzer (DMA), an optical particle counter (OPC) and the single particle trap system. Polystylene latex standard (PSL) particles (0.5, 1.0 and 2.0 μm) were generated and classified according to the charge by the DMA. Singly charged 0.5 and 1.0 μm particles and doubly charged 2.0 μm particles were used as test particles. The single particle trap system was composed of a light scattering signal detector and a visualization cell. When the particle passed through the detector, trigger signal with a given delay time sent to the solenoid valves upstream and downstream of the visualization cell for trapping the particle in the visualization cell. The motion of particle in the visualization cell was monitored by CCD camera and the gravitational settling velocity and the electrostatic migration velocity were measured from the video image. The aerodynamic diameter obtained from the settling velocity was in good agreement with Stokes diameter calculated from the electrostatic migration velocity for individual particles. It was also found that the aerodynamic diameter obtained from the settling velocity was a one-to-one function of the scattered light intensity of individual particles. The applicability of this system will be discussed.

A thermodynamic description of the system Pd-Rh-H-D-T

Energy Technology Data Exchange (ETDEWEB)

Joubert, J.-M., E-mail: jean-marc.joubert@icmpe.cnrs.fr [Chimie Metallurgique des Terres Rares, Institut de Chimie et des Materiaux Paris-Est, CNRS, Universite Paris-Est, UMR 7182, 2-8 Rue Henri Dunant, F-94320 Thiais (France); Thiebaut, S. [CEA/DAM/Valduc, F-21120 Is sur Tille (France)

2011-02-15

The quinary system D-H-Pd-Rh-T has been described thermodynamically by the CALPHAD approach. Previous descriptions of the binary subsystems have been used. To model the high pressure data an equation of state for the gases D{sub 2} and T{sub 2} compatible with the CALPHAD approach has been obtained similar to that previously used for H{sub 2}. A complete literature search has been undertaken for the three ternary systems H-Pd-Rh, D-Pd-Rh and Pd-Rh-T and the most significant experimental data have been selected for a thermodynamic assessment of these systems. In order to complement the available data, pressure-composition curves have been measured at different temperatures for the two last systems in the present work. Calculations and optimization of the system under para-equilibrium conditions, i.e. in pseudo-binary systems (Pd,Rh)-H, (Pd,Rh)-D or (Pd,Rh)-T, have been achieved using a pseudo-atom describing the Pd-Rh solid solution. This special method allows the presence of a miscibility gap in the binary metallic system to be dealt with. We show that a simple combination of the binary systems alone is unable to properly describe these ternary systems and that ternary interaction parameters have to be introduced. The binary and ternary systems may then be combined to perform calculations in the quinary D-H-Pd-Rh-T system. It is believed that extrapolation in systems containing different isotopes are fairly accurate provided that the so-called Toop model is used.

Unambiguous discrimination of mixed states: A description based on system-ancilla coupling

International Nuclear Information System (INIS)

Zhou, Xiang-Fa; Zhang, Yong-Sheng; Guo, Guang-Can

2007-01-01

We propose a general description for the unambiguous discrimination of mixed states according to the system-environment coupling, and present a procedure to reduce this to a standard semidefinite programming problem. In the two-state case, we introduce the canonical vectors and partly simplify the problem to the case of discrimination between pairs of canonical vectors. By considering the positivity of the 2x2 matrices, we obtain a series of new upper bounds for the total success probability, which depends on both the prior probabilities and specific state structures

A geometric Hamiltonian description of composite quantum systems and quantum entanglement

Science.gov (United States)

Pastorello, Davide

2015-05-01

Finite-dimensional Quantum Mechanics can be geometrically formulated as a proper classical-like Hamiltonian theory in a projective Hilbert space. The description of composite quantum systems within the geometric Hamiltonian framework is discussed in this paper. As summarized in the first part of this work, in the Hamiltonian formulation the phase space of a quantum system is the Kähler manifold given by the complex projective space P(H) of the Hilbert space H of the considered quantum theory. However the phase space of a bipartite system must be P(H1 ⊗ H2) and not simply P(H1) × P(H2) as suggested by the analogy with Classical Mechanics. A part of this paper is devoted to manage this problem. In the second part of the work, a definition of quantum entanglement and a proposal of entanglement measure are given in terms of a geometrical point of view (a rather studied topic in recent literature). Finally two known separability criteria are implemented in the Hamiltonian formalism.

Data integration, systems approach and multilevel description of complex biosystems

International Nuclear Information System (INIS)

Hernández-Lemus, Enrique

2013-01-01

Recent years have witnessed the development of new quantitative approaches and theoretical tenets in the biological sciences. The advent of high throughput experiments in genomics, proteomics and electrophysiology (to cite just a few examples) have provided the researchers with unprecedented amounts of data to be analyzed. Large datasets, however can not provide the means to achieve a complete understanding of the underlying biological phenomena, unless they are supplied with a solid theoretical framework and with proper analytical tools. It is now widely accepted that by using and extending some of the paradigmatic principles of what has been called complex systems theory, some degree of advance in this direction can be attained. We will be presenting ways in which by using data integration techniques (linear, non-linear, combinatorial, graphical), multidimensional-multilevel descriptions (multifractal modeling, dimensionality reduction, computational learning), as well as an approach based in systems theory (interaction maps, probabilistic graphical models, non-equilibrium physics) have allowed us to better understand some problems in the interface of Statistical Physics and Computational Biology

The Reification of Patterns in the Design of Description-Driven Systems

CERN Document Server

Le Goff, J M; Kovács, Z; McClatchey, R

2001-01-01

To address the issues of reusability and evolvability in designing self- describing systems, this paper proposes a pattern-based, object-oriented, description-driven system architecture. The proposed architecture embodies four pillars - first, the adoption of a multi-layered meta-modeling architecture and reflective meta-level architecture, second, the identification of four data modeling relationships that must be made explicit such that they can be examined and modified dynamically, third, the identification of five design patterns which have emerged from practice and have proved essential in providing reusable building blocks for data management, and fourth, the encoding of the structural properties of the five design patterns by means of one pattern, the Graph pattern. The CRISTAL research project served as the basis onto which the pattern-based meta-object approach has been applied. The proposed architecture allows the realization of reusability and adaptability, and is fundamental in the specification o...

System design package for SIMS prototype system 4, solar heating and domestic hot water

Science.gov (United States)

1978-01-01

The system consisted of a modular designed prepackaged solar unit, containing solar collectors, a rock storage container, blowers, dampers, ducting, air-to-water heat exchanger, DHW preheat tank, piping, and system controls. The system was designed to be installed adjacent to a small single family dwelling. The description, performance specification, subsystem drawings, verification plan/procedure, and hazard analysis of the system were packaged for evaluation.

Single-photon sensitive fast ebCMOS camera system for multiple-target tracking of single fluorophores: application to nano-biophotonics

Science.gov (United States)

Cajgfinger, Thomas; Chabanat, Eric; Dominjon, Agnes; Doan, Quang T.; Guerin, Cyrille; Houles, Julien; Barbier, Remi

2011-03-01

Nano-biophotonics applications will benefit from new fluorescent microscopy methods based essentially on super-resolution techniques (beyond the diffraction limit) on large biological structures (membranes) with fast frame rate (1000 Hz). This trend tends to push the photon detectors to the single-photon counting regime and the camera acquisition system to real time dynamic multiple-target tracing. The LUSIPHER prototype presented in this paper aims to give a different approach than those of Electron Multiplied CCD (EMCCD) technology and try to answer to the stringent demands of the new nano-biophotonics imaging techniques. The electron bombarded CMOS (ebCMOS) device has the potential to respond to this challenge, thanks to the linear gain of the accelerating high voltage of the photo-cathode, to the possible ultra fast frame rate of CMOS sensors and to the single-photon sensitivity. We produced a camera system based on a 640 kPixels ebCMOS with its acquisition system. The proof of concept for single-photon based tracking for multiple single-emitters is the main result of this paper.

Olkiluoto site description 2011

International Nuclear Information System (INIS)

2012-12-01

This fourth version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2008 with the data and knowledge obtained up to December 2010. A descriptive model of the site (the Site Descriptive Model, SDM), i.e. a model describing the geological and hydrogeological structure of the site, properties of the bedrock and the groundwater and its flow, and the associated interacting processes and mechanisms. The SDM is divided into six parts: surface system, geology, rock mechanics, hydrogeology, hydrogeochemistry and transport properties

Olkiluoto site description 2011

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-12-15

This fourth version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2008 with the data and knowledge obtained up to December 2010. A descriptive model of the site (the Site Descriptive Model, SDM), i.e. a model describing the geological and hydrogeological structure of the site, properties of the bedrock and the groundwater and its flow, and the associated interacting processes and mechanisms. The SDM is divided into six parts: surface system, geology, rock mechanics, hydrogeology, hydrogeochemistry and transport properties.

System Description:

DEFF Research Database (Denmark)

Schürmann, Carsten; Poswolsky, Adam

2009-01-01

Delphin is a functional programming language [Adam Poswolsky and Carsten Schürmann. Practical programming with higher-order encodings and dependent types. In European Symposium on Programming (ESOP), 2008] utilizing dependent higher-order datatypes. Delphin's two-level type-system cleanly separates...

Single Point Vulnerability Analysis of Automatic Seismic Trip System

International Nuclear Information System (INIS)

Oh, Seo Bin; Chung, Soon Il; Lee, Yong Suk; Choi, Byung Pil

2016-01-01

Single Point Vulnerability (SPV) analysis is a process used to identify individual equipment whose failure alone will result in a reactor trip, turbine generator failure, or power reduction of more than 50%. Automatic Seismic Trip System (ASTS) is a newly installed system to ensure the safety of plant when earthquake occurs. Since this system directly shuts down the reactor, the failure or malfunction of its system component can cause a reactor trip more frequently than other systems. Therefore, an SPV analysis of ASTS is necessary to maintain its essential performance. To analyze SPV for ASTS, failure mode and effect analysis (FMEA) and fault tree analysis (FTA) was performed. In this study, FMEA and FTA methods were performed to select SPV equipment of ASTS. D/O, D/I, A/I card, seismic sensor, and trip relay had an effect on the reactor trip but their single failure will not cause reactor trip. In conclusion, ASTS is excluded as SPV. These results can be utilized as the basis data for ways to enhance facility reliability such as design modification and improvement of preventive maintenance procedure

Single Point Vulnerability Analysis of Automatic Seismic Trip System

Energy Technology Data Exchange (ETDEWEB)

Oh, Seo Bin; Chung, Soon Il; Lee, Yong Suk [FNC Technology Co., Yongin (Korea, Republic of); Choi, Byung Pil [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

Single Point Vulnerability (SPV) analysis is a process used to identify individual equipment whose failure alone will result in a reactor trip, turbine generator failure, or power reduction of more than 50%. Automatic Seismic Trip System (ASTS) is a newly installed system to ensure the safety of plant when earthquake occurs. Since this system directly shuts down the reactor, the failure or malfunction of its system component can cause a reactor trip more frequently than other systems. Therefore, an SPV analysis of ASTS is necessary to maintain its essential performance. To analyze SPV for ASTS, failure mode and effect analysis (FMEA) and fault tree analysis (FTA) was performed. In this study, FMEA and FTA methods were performed to select SPV equipment of ASTS. D/O, D/I, A/I card, seismic sensor, and trip relay had an effect on the reactor trip but their single failure will not cause reactor trip. In conclusion, ASTS is excluded as SPV. These results can be utilized as the basis data for ways to enhance facility reliability such as design modification and improvement of preventive maintenance procedure.

Single-Phase Single-Stage Grid Tied Solar PV System with Active Power Filtering Using Power Balance Theory

Science.gov (United States)

Singh, Yashi; Hussain, Ikhlaq; Singh, Bhim; Mishra, Sukumar

2018-03-01

In this paper, power quality features such as harmonics mitigation, power factor correction with active power filtering are addressed in a single-stage, single-phase solar photovoltaic (PV) grid tied system. The Power Balance Theory (PBT) with perturb and observe based maximum power point tracking algorithm is proposed for the mitigation of power quality problems in a solar PV grid tied system. The solar PV array is interfaced to a single phase AC grid through a Voltage Source Converter (VSC), which provides active power flow from a solar PV array to the grid as well as to the load and it performs harmonics mitigation using PBT based control. The solar PV array power varies with sunlight and due to this, the solar PV grid tied VSC works only 8-10 h per day. At night, when PV power is zero, the VSC works as an active power filter for power quality improvement, and the load active power is delivered by the grid to the load connected at the point of common coupling. This increases the effective utilization of a VSC. The system is modelled and simulated using MATLAB and simulated responses of the system at nonlinear loads and varying environmental conditions are also validated experimentally on a prototype developed in the laboratory.

Fort Hood Solar Total Energy Project. Volume II. Preliminary design. Part 1. System criteria and design description. Final report

Energy Technology Data Exchange (ETDEWEB)

None,

1979-01-01

This volume documents the preliminary design developed for the Solar Total Energy System to be installed at Fort Hood, Texas. Current system, subsystem, and component designs are described and additional studies which support selection among significant design alternatives are presented. Overall system requirements which form the system design basis are presented. These include program objectives; performance and output load requirements; industrial, statutory, and regulatory standards; and site interface requirements. Material in this section will continue to be issued separately in the Systems Requirements Document and maintained current through revision throughout future phases of the project. Overall system design and detailed subsystem design descriptions are provided. Consideration of operation and maintenance is reflected in discussion of each subsystem design as well as in an integrated overall discussion. Included are the solar collector subsystem; the thermal storage subsystem, the power conversion sybsystem (including electrical generation and distribution); the heating/cooling and domestic hot water subsystems; overall instrumentation and control; and the STES building and physical plant. The design of several subsystems has progressed beyond the preliminary stage; descriptions for such subsystems are therefore provided in more detail than others to provide complete documentation of the work performed. In some cases, preliminary design parameters require specific verificaton in the definitive design phase and are identified in the text. Subsystem descriptions will continue to be issued and revised separately to maintain accuracy during future phases of the project. (WHK)

Longitudinal single-bunch instabilities

International Nuclear Information System (INIS)

Migliorati, M.; Palumbo, L.; Rome Univ. La Sapienza, Rome

2001-02-01

After introducing the concepts of longitudinal wakefield and coupling impedance, it is reviewed the theory of longitudinal single-bunch collective effects in storage rings. From the Fokker-Planck equation it is first derived the stationary solution describing the natural single-bunch regime, and then treat the problem of microwave instability, showing the different approaches used for estimating the threshold current. The lecture is ended with the semi-empirical laws that allow everyone to obtain the single-bunch behaviour above threshold, and with a description of the simulation codes that are now reliable tools for investigating all these effects

Tank waste remediation system technical baseline summary description

International Nuclear Information System (INIS)

Raymond, R.E.

1998-01-01

This document is one of the tools used to develop and control the mission work as depicted in the included figure. This Technical Baseline Summary Description document is the top-level tool for management of the Technical Baseline for waste storage operations

A New Three-Dimensional High-Accuracy Automatic Alignment System For Single-Mode Fibers

Science.gov (United States)

Yun-jiang, Rao; Shang-lian, Huang; Ping, Li; Yu-mei, Wen; Jun, Tang

1990-02-01

In order to achieve the low-loss splices of single-mode fibers, a new three-dimension high-accuracy automatic alignment system for single -mode fibers has been developed, which includes a new-type three-dimension high-resolution microdisplacement servo stage driven by piezoelectric elements, a new high-accuracy measurement system for the misalignment error of the fiber core-axis, and a special single chip microcomputer processing system. The experimental results show that alignment accuracy of ±0.1 pin with a movable stroke of -±20μm has been obtained. This new system has more advantages than that reported.

[Systemic inflammation: theoretical and methodological approaches to description of general pathological process model. Part 3. Backgroung for nonsyndromic approach].

Science.gov (United States)

Gusev, E Yu; Chereshnev, V A

2013-01-01

Theoretical and methodological approaches to description of systemic inflammation as general pathological process are discussed. It is shown, that there is a need of integration of wide range of types of researches to develop a model of systemic inflammation.

System design package for IBM system one: solar heating and domestic hot water

Science.gov (United States)

1977-01-01

This report is a collation of documents and drawings that describe a prototype solar heating and hot water system using air as the collector fluid and a pebble bed for heat storage. The system was designed for installation into a single family dwelling. The description, performance specification, subsystem drawings, verification plan/procedure, and hazard analysis of the system was packaged for evaluation of the system with information sufficient to assemble a similar system.

Zero-Voltage Ride-Through Capability of Single-Phase Grid-Connected Photovoltaic Systems

Directory of Open Access Journals (Sweden)

Zhen Zhang

2017-03-01

Full Text Available Distributed renewable energy systems play an increasing role in today’s energy paradigm. Thus, intensive research activities have been centered on improving the performance of renewable energy systems, including photovoltaic (PV systems, which should be of multiple-functionality. That is, the PV systems should be more intelligent in the consideration of grid stability, reliability, and fault protection. Therefore, in this paper, the performance of single-phase grid-connected PV systems under an extreme grid fault (i.e., when the grid voltage dips to zero is explored. It has been revealed that combining a fast and accurate synchronization mechanism with appropriate control strategies for the zero-voltage ride-through (ZVRT operation is mandatory. Accordingly, the representative synchronization techniques (i.e., the phase-locked loop (PLL methods in the ZVRT operation are compared in terms of detection precision and dynamic response. It shows that the second-order generalized integrator (SOGI-PLL is a promising solution for single-phase systems in the case of fault ride-through. A control strategy by modifying the SOGI-PLL scheme is then introduced to single-phase grid-connected PV systems for ZVRT operation. Simulations are performed to verify the discussions. The results have demonstrated that the proposed method can help single-phase PV systems to temporarily ride through zero-voltage faults with good dynamics.

Study on irradiation effects of nucleus electromagnetic pulse on single chip computer system

International Nuclear Information System (INIS)

Hou Minsheng; Liu Shanghe; Wang Shuping

2001-01-01

Intense electromagnetic pulse, namely nucleus electromagnetic pulse (NEMP), lightning electromagnetic pulse (LEMP) and high power microwave (HPM), can disturb and destroy the single chip computer system. To study this issue, the authors made irradiation experiments by NEMPs generated by gigahertz transversal electromagnetic (GTEM) Cell. The experiments show that shutdown, restarting, communication errors of the single chip microcomputer system would occur when it was irradiated by the NEMPs. Based on the experiments, the cause on the effects on the single chip microcomputer system is discussed

Relativistic description of atomic nuclei

International Nuclear Information System (INIS)

Krutov, V.A.

1985-01-01

Papers on the relativistic description of nuclei are reviewed. The Brown and Rho ''small'' bag'' model is accepted for hardrons. Meson exchange potentials of the nucleon-nucleon interaction have been considered. Then the transition from a system of two interacting nucleons has been performed to the relativistic nucleus description as a multinucleon system on the basis of OBEP (one-boson exchange potential). The proboem of OPEP (one-pion-exchange potential) inclusion to a relativistic scheme is discussed. Simplicity of calculations and attractiveness of the Walecka model for specific computations and calculations was noted. The relativistic model of nucleons interacting through ''effective'' scalar and vector boson fields was used in the Walacka model for describing neutronaand nuclear mater matters

Development of pulsation technique for single ion hit system

Energy Technology Data Exchange (ETDEWEB)

Sakai, Takuro; Hamano, Tsuyoshi; Hirao, Toshio; Kamiya, Tomihiro [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

1996-12-01

When a high energy heavy ion enters into a substance, high density of ionization and excitement occurrs along its flying trace. Especially, when such an ion enters into a semiconductor cell, a bit inversion called single event is occurred or a phenomenon destroyed element itself on case of the worst is formed. The present semiconductor cell is made in a size of some micron square, as different from its accumulated degree. In order to analyze the single event phenomenon formed by entering ion into such fine region in detail, a technique possible enter heavy ion beam with space resolution under 1 micron to each sample is necessary. In order to develop this technique, a static type high speed beam switch for control of entering a beam into a sample and a single ion detector for detecting entrance of ion into the sample were installed to heavy ion microbeam forming apparatus. The single ion hit system in Takasaki Radiation Chemistry Research Establishment, JAERI succeeded in detection and control technique of the single ion and control of noise due to pulsization and finished development of basic technique of the single ion hit, since now. After today, it is planned to hit actually the single ion onto the sample and evaluate its accuracy. (G.K.)

Nickel-Titanium Single-file System in Endodontics.

Science.gov (United States)

Dagna, Alberto

2015-10-01

This work describes clinical cases treated with a innovative single-use and single-file nickel-titanium (NiTi) system used in continuous rotation. Nickel-titanium files are commonly used for root canal treatment but they tend to break because of bending stresses and torsional stresses. Today new instruments used only for one treatment have been introduced. They help the clinician to make the root canal shaping easier and safer because they do not require sterilization and after use have to be discarded. A new sterile instrument is used for each treatment in order to reduce the possibility of fracture inside the canal. The new One Shape NiTi single-file instrument belongs to this group. One Shape is used for complete shaping of root canal after an adequate preflaring. Its protocol is simple and some clinical cases are presented. It is helpful for easy cases and reliable for difficult canals. After 2 years of clinical practice, One Shape seems to be helpful for the treatment of most of the root canals, with low risk of separation. After each treatment, the instrument is discarded and not sterilized in autoclave or re-used. This single-use file simplifies the endodontic therapy, because only one instrument is required for canal shaping of many cases. The respect of clinical protocol guarantees predictable good results.

System Design Package for SIMS Prototype System 3, Solar Heating and Domestic Hot Water

Science.gov (United States)

1978-01-01

A collation of documents and drawings are presented that describe a prototype solar heating and hot water system using liquid flat plate collectors and a gas or electric furnace energy subsystem. The system was designed for installation into a single-family dwelling. The description, performance specification, subsystem drawings, verification plan/procedure, and hazard analysis of the system are packaged for evaluation of the system with information sufficient to assemble a similar system.

Description of the prototype fast reactor at Dounreay

International Nuclear Information System (INIS)

Jensen, S.E.; Oelgaard, P.L.

1995-12-01

The Prototype Fast Reactor (PFR) at Dounreay, UK, started operation in 1975 and was closed down in 1994. The present report contains a description of the PFR nuclear power plant, based on information available in literature and on information supplied during a visit to the plant. The report covers a description of the site and plant arrangement, the buildings and structures, the reactor core and other vessel internals, the control system, the main cooling system, the decay heat removal system, the emergency core cooling system, the containment system, the steam and power conversion system, the fuel handling system, plant safety features, the control and instrumentation systems and the sodium purification systems. (au) 16 refs

Job Analysis, Job Descriptions, and Performance Appraisal Systems.

Science.gov (United States)

Sims, Johnnie M.; Foxley, Cecelia H.

1980-01-01

Job analysis, job descriptions, and performance appraisal can benefit student services administration in many ways. Involving staff members in the development and implementation of these techniques can increase commitment to and understanding of the overall objectives of the office, as well as communication and cooperation among colleagues.…

Osiris reactor descriptive report

International Nuclear Information System (INIS)

1976-03-01

OSIRIS is a swimming pool reactor of 70 MW thermal power. Its main purpose is the irradiation of reactor materials in high neutron flux. A description is given of the air conditioning, ventilation, and radioactive gas removal system. (R.L.)

Master-slave synchronization of Lorenz systems using a single controller

International Nuclear Information System (INIS)

Oancea, Servilia; Grosu, Florin; Lazar, Anca; Grosu, Ioan

2009-01-01

A single controller for synchronization of two Lorenz systems is obtained by using Lyapunov function. Numerical results are given for the all three cases with one controller in each equation. Controller contains two or three variables of the master system.

Sewage Solids Irradiator Transportation System (SSITS) cask: preliminary design description

International Nuclear Information System (INIS)

Eakes, R.G.; Kempka, S.N.; Lamoreaux, G.H.; Sutherland, S.H.

1983-02-01

The preliminary design of the Sewage Solids Irradiator Transportation System (SSITS) Cask is presented in this document. The SSITS cask is to be used for the transport of radioactive cesium chloride and strontium fluoride capsules which are of use in irradiators or as heat sources. The SSITS cask is approximately 1.4 m in diameter, 1.3 m high, weighs roughly 9 t, provides 33 cm of steel shielding, and can dissipate up to 5.2 kW of decay heat. The cask design criteria are identified and a description of the cask design and operation is provided. Detailed analyses of the design were performed to demonstrate licensability of the cask by the Nuclear Regulatory Commission (NRC). Results of the analyses indicate that the preliminary design is in compliance with the pertinent regulatory requirements for licensing of a radioactive material transportation container

Surface energy and radiation balance systems - General description and improvements

Science.gov (United States)

Fritschen, Leo J.; Simpson, James R.

1989-01-01

Surface evaluation of sensible and latent heat flux densities and the components of the radiation balance were desired for various vegetative surfaces during the ASCOT84 experiment to compare with modeled results and to relate these values to drainage winds. Five battery operated data systems equipped with sensors to determine the above values were operated for 105 station days during the ASCOT84 experiment. The Bowen ratio energy balance technique was used to partition the available energy into the sensible and latent heat flux densities. A description of the sensors and battery operated equipment used to collect and process the data is presented. In addition, improvements and modifications made since the 1984 experiment are given. Details of calculations of soil heat flow at the surface and an alternate method to calculate sensible and latent heat flux densities are provided.

Design optimization of single-main-amplifier KrF laser-fusion systems

International Nuclear Information System (INIS)

Harris, D.B.; Pendergrass, J.H.

1985-01-01

KrF lasers appear to be a very promising laser fusion driver for commercial applications. The Large Amplifier Module for the Aurora Laser System at Los Alamos is the largest KrF laser in the world and is currently operating at 5 kJ with 10 to 15 kJ eventually expected. The next generation system is anticipated to be a single-main-amplifier system that generates approximately 100 kJ. This paper examines the cost and efficiency tradeoffs for a complete single-main-amplifier KrF laser fusion experimental facility. It has been found that a 7% efficient $310/joule complete laser-fusion system is possible by using large amplifier modules and high optical fluences

Systems for the monitoring of working conditions relating to health and safety : extensive descriptions : Belgium, Germany, Luxembourg, The Netherlands

NARCIS (Netherlands)

Prins, R.; Verboon, F.

1991-01-01

This report contains the extensive descriptions of (some of) the monitoring systems on health and safety in use in the Benelux countries and Germany. The project of which this report is a part aimed at gathering information on monitoring systems throughout the EC member states.

Evaluation of the adverse events following immunizations surveillance system in Harare City, Zimbabwe, 2016: a descriptive cross sectional study.

Science.gov (United States)

Zvanaka, Sithole; Tsitsi, Juru; Chonzi, Prosper; Shambira, Gerald; Gombe, Notion Tafara; Tshimanga, Mufuta

2017-01-01

Vaccines safety are monitored by looking for Adverse Events Following Immunizations (AEFIs). A review of the 2014 Harare City consolidated monthly return form (T5) revealed that 28 AEFIs were seen in 2014. However, only 21 were reported through the system. We therefore evaluated the Harare City AEFI surveillance system to assess its usefulness. A descriptive cross sectional study was conducted. Twenty one of 41 clinics were randomly selected and 51 health workers were randomly recruited. Interviewer administered questionnaires were used to collect data. Epi info 7 was used to generate frequencies, means and proportions. Out of 51 respondents, 50 (98%) knew the purpose of AEFI system, 48 (94%) knew at least two presenting symptoms of AEFIs and 39 (77%) knew the correct date of form submission to the next level. Receiving no feedback 24 (47.1%), fear of victimisation 16 (31.4%) and work overload 11 (21.6%) were the major reasons for under reporting. Eighty six percent perceived the system to be simple and 43 (84%) were willing to continue participating. Fifty three percent (27) reported taking public health actions (such as awareness campaigns & making follow ups) basing on AEFI data collected. All 46 reviewed forms were completely filled and submitted in time. All 21 clinics had written AEFI guidelines and case definitions. Only 14 of 21 clinics had adequately stocked emergency drugs. The total cost for a single notification was estimated at US$22.30. The system was useful, simple, acceptable, timely, stable, representative but costly. The good performance of the system reported in this evaluation could be attributed to high health worker knowledge. Following this evaluation, replenishment of out of stock drugs and follow up of missing 2014 AEFI feedback from MCAZ were done. In addition, making the system electronic is recommended.

A comparison of hardware description languages. [describing digital systems structure and behavior to a computer

Science.gov (United States)

Shiva, S. G.

1978-01-01

Several high level languages which evolved over the past few years for describing and simulating the structure and behavior of digital systems, on digital computers are assessed. The characteristics of the four prominent languages (CDL, DDL, AHPL, ISP) are summarized. A criterion for selecting a suitable hardware description language for use in an automatic integrated circuit design environment is provided.

Single phase inverter for a three phase power generation and distribution system

Science.gov (United States)

Lindena, S. J.

1976-01-01

A breadboard design of a single-phase inverter with sinusoidal output voltage for a three-phase power generation and distribution system was developed. The three-phase system consists of three single-phase inverters, whose output voltages are connected in a delta configuration. Upon failure of one inverter the two remaining inverters will continue to deliver three-phase power. Parallel redundancy as offered by two three-phase inverters is substituted by one three-phase inverter assembly with high savings in volume, weight, components count and complexity, and a considerable increase in reliability. The following requirements must be met: (1) Each single-phase, current-fed inverter must be capable of being synchronized to a three-phase reference system such that its output voltage remains phaselocked to its respective reference voltage. (2) Each single-phase, current-fed inverter must be capable of accepting leading and lagging power factors over a range from -0.7 through 1 to +0.7.

X-ray quality increasing system controlled by single-chip microcomputer in single phase fluoroscopy unit

International Nuclear Information System (INIS)

Wang Qiaolin; Gu Hongmei

2004-01-01

Objective: To decrease the amount of radiation that doctor and patient receives by increasing X-ray quality. Methods: Using Single-chip Microcomputer technology, test and modulate AC(Alternating Current) from high voltage generator by IGBT. X-ray tube generates X-rays only at high energy area. Thus the amount of radiation decreases. Results: The tube current decreases remarkably and the amount of radiation that doctor and patient receives decreases effectively. Conclusion: the system can effectively decrease the amount of radiation and is widely applicable to the upgrade of all kinds of single phase X-ray units. (authors)

The description of neutron and giant resonances within the quasiparticle-phonon nuclear model

International Nuclear Information System (INIS)

Soloviev, V.G.

1978-01-01

The general assumptions of the quasiparticle-phonon model of complex nuclei are given. The choice of the model Hamiltonian as an average field and residual forces is discussed. The phonon description and quasiparticle-phonon interaction are presented. The system of basic equations and their approximate solutions are obtained. The approximation is chosen so as to obtain the most correct description of few-quasiparticle components rather than of the whole wave function. The method of strength functions is presented, which plays a decisive role in practical realization of the quasiparticle-phonon model for the description of some properties of complex nuclei. The range of applicability of the quasiparticle-phonon nuclear model is determined as few-quasiparticle components of the wave functions at low, intermediate and high excitation energies averaged in a certain energy interval. The fragmentation of single-particle states in deformed nuclei is studied within this model. The dependence of neutron strength functions on the excitation energy is investigated for the transfer reactions of the type (d,p) and (d,t). The s - ,p - , and d-wave neutron strength functions are calculated at the neutron binding energy Bsub(n). A satisfactory agreement with experiment is obtained. A correct description of the radiative strength functions in spherical nuclei is obtained. The influence of the tail of the giant dipole resonance on the E1-strength functions is studied. The energies and EΛ-strength functions for giant multipole resonances in spherical and deformed nuclei are calculated. A correct description of their widths is obtained. (author)

Diffracted X-ray tracking: new system for single molecular detection with X-rays

CERN Document Server

Sasaki, Y C; Adachi, S; Suzuki, Y; Yagi, N

2001-01-01

We propose a new X-ray methodology for direct observations of the behaviors of single molecular units in real time and real space. This new system, which we call Diffracted X-ray Tracking (DXT), monitors the Brownian motions of a single molecular unit by observations of X-ray diffracted spots from a nanocrystal, tightly bound to the individual single molecular unit in bio-systems. DXT does not determine any translational movements, but only orientational movements.

Diffracted X-ray tracking: new system for single molecular detection with X-rays

International Nuclear Information System (INIS)

Sasaki, Y.C.; Okumura, Y.; Adachi, S.; Suzuki, Y.; Yagi, N.

2001-01-01

We propose a new X-ray methodology for direct observations of the behaviors of single molecular units in real time and real space. This new system, which we call Diffracted X-ray Tracking (DXT), monitors the Brownian motions of a single molecular unit by observations of X-ray diffracted spots from a nanocrystal, tightly bound to the individual single molecular unit in bio-systems. DXT does not determine any translational movements, but only orientational movements

Modeling and Control of a Single-Phase Marine Cooling System

DEFF Research Database (Denmark)

Hansen, Michael; Stoustrup, Jakob; Bendtsen, Jan Dimon

2013-01-01

This paper presents two model-based control design approaches for a single-phase marine cooling system. Models are derived from first principles and aim at describing significant system dynamics including nonlinearities and transport delays, while keeping the model complexity low. The two...

Probing correlated quantum many-body systems at the single-particle level

Energy Technology Data Exchange (ETDEWEB)

Endres, Manuel

2013-02-27

The detection of correlation and response functions plays a crucial role in the experimental characterization of quantum many-body systems. In this thesis, we present novel techniques for the measurement of such functions at the single-particle level. Specifically, we show the single-atom- and single-site-resolved detection of an ultracold quantum gas in an optical lattice. The quantum gas is described by the Bose-Hubbard model, which features a zero temperature phase transition from a superfluid to a Mott-insulating state, a paradigm example of a quantum phase transition. We used the aforementioned detection techniques to study correlation and response properties across the superfluid-Mott-insulator transition. The single-atom sensitivity of our method is achieved by fluorescence detection of individual atoms with a high signal-to-noise ratio. A high-resolution objective collects the fluorescence light and yields in situ 'snapshots' of the quantum gas that allow for a single-site-resolved reconstruction of the atomic distribution. This allowed us to measure two-site and non-local correlation-functions across the superfluid-Mott-insulator transition. Non-local correlation functions are based on the information of an extended region of the system and play an important role for the characterization of low-dimensional quantum phases. While non-local correlation functions were so far only theoretical tools, our results show that they are actually experimentally accessible. Furthermore, we used a new thermometry scheme, based on the counting of individual thermal excitations, to measure the response of the system to lattice modulation. Using this method, we studied the excitation spectrum of the system across the two-dimensional superfluid-Mott-insulator transition. In particular, we detected a 'Higgs' amplitude mode in the strongly-interacting superfluid close to the transition point where the system is described by an effectively Lorentz

Probing correlated quantum many-body systems at the single-particle level

International Nuclear Information System (INIS)

Endres, Manuel

2013-01-01

The detection of correlation and response functions plays a crucial role in the experimental characterization of quantum many-body systems. In this thesis, we present novel techniques for the measurement of such functions at the single-particle level. Specifically, we show the single-atom- and single-site-resolved detection of an ultracold quantum gas in an optical lattice. The quantum gas is described by the Bose-Hubbard model, which features a zero temperature phase transition from a superfluid to a Mott-insulating state, a paradigm example of a quantum phase transition. We used the aforementioned detection techniques to study correlation and response properties across the superfluid-Mott-insulator transition. The single-atom sensitivity of our method is achieved by fluorescence detection of individual atoms with a high signal-to-noise ratio. A high-resolution objective collects the fluorescence light and yields in situ 'snapshots' of the quantum gas that allow for a single-site-resolved reconstruction of the atomic distribution. This allowed us to measure two-site and non-local correlation-functions across the superfluid-Mott-insulator transition. Non-local correlation functions are based on the information of an extended region of the system and play an important role for the characterization of low-dimensional quantum phases. While non-local correlation functions were so far only theoretical tools, our results show that they are actually experimentally accessible. Furthermore, we used a new thermometry scheme, based on the counting of individual thermal excitations, to measure the response of the system to lattice modulation. Using this method, we studied the excitation spectrum of the system across the two-dimensional superfluid-Mott-insulator transition. In particular, we detected a 'Higgs' amplitude mode in the strongly-interacting superfluid close to the transition point where the system is described by an effectively Lorentz-invariant low-energy theory

Primary Numbers Database for ATLAS Detector Description Parameters

CERN Document Server

Vaniachine, A; Malon, D; Nevski, P; Wenaus, T

2003-01-01

We present the design and the status of the database for detector description parameters in ATLAS experiment. The ATLAS Primary Numbers are the parameters defining the detector geometry and digitization in simulations, as well as certain reconstruction parameters. Since the detailed ATLAS detector description needs more than 10,000 such parameters, a preferred solution is to have a single verified source for all these data. The database stores the data dictionary for each parameter collection object, providing schema evolution support for object-based retrieval of parameters. The same Primary Numbers are served to many different clients accessing the database: the ATLAS software framework Athena, the Geant3 heritage framework Atlsim, the Geant4 developers framework FADS/Goofy, the generator of XML output for detector description, and several end-user clients for interactive data navigation, including web-based browsers and ROOT. The choice of the MySQL database product for the implementation provides addition...

Physics detector simulation facility system software description

International Nuclear Information System (INIS)

Allen, J.; Chang, C.; Estep, P.; Huang, J.; Liu, J.; Marquez, M.; Mestad, S.; Pan, J.; Traversat, B.

1991-12-01

Large and costly detectors will be constructed during the next few years to study the interactions produced by the SSC. Efficient, cost-effective designs for these detectors will require careful thought and planning. Because it is not possible to test fully a proposed design in a scaled-down version, the adequacy of a proposed design will be determined by a detailed computer model of the detectors. Physics and detector simulations will be performed on the computer model using high-powered computing system at the Physics Detector Simulation Facility (PDSF). The SSCL has particular computing requirements for high-energy physics (HEP) Monte Carlo calculations for the simulation of SSCL physics and detectors. The numerical calculations to be performed in each simulation are lengthy and detailed; they could require many more months per run on a VAX 11/780 computer and may produce several gigabytes of data per run. Consequently, a distributed computing environment of several networked high-speed computing engines is envisioned to meet these needs. These networked computers will form the basis of a centralized facility for SSCL physics and detector simulation work. Our computer planning groups have determined that the most efficient, cost-effective way to provide these high-performance computing resources at this time is with RISC-based UNIX workstations. The modeling and simulation application software that will run on the computing system is usually written by physicists in FORTRAN language and may need thousands of hours of supercomputing time. The system software is the ''glue'' which integrates the distributed workstations and allows them to be managed as a single entity. This report will address the computing strategy for the SSC

Modeling single versus multiple systems in implicit and explicit memory.

Science.gov (United States)

Starns, Jeffrey J; Ratcliff, Roger; McKoon, Gail

2012-04-01

It is currently controversial whether priming on implicit tasks and discrimination on explicit recognition tests are supported by a single memory system or by multiple, independent systems. In a Psychological Review article, Berry and colleagues used mathematical modeling to address this question and provide compelling evidence against the independent-systems approach. Copyright © 2012 Elsevier Ltd. All rights reserved.

Raman spectroscopy and single-photon source in an ion-cavity system

International Nuclear Information System (INIS)

Goncalves de Barros, H.

2010-01-01

The work presented in this thesis explores the interaction between a single trapped 40Ca+ ion and the electromagnetic field inside a high-finesse optical cavity. The coupling takes place via the use of a vacuum stimulated Raman transition, which transfers atomic population from the S1/2 to the D3/2 manifolds of the calcium ion producing a photon in the cavity. This photon is measured and properties of the system are evaluated. Spectroscopy measurements of the Raman transitions are performed and all possible transitions are identified for different polarizations of both drive laser and cavity fields. The system is also used to deterministically produce single photons. Simulation curves quantitatively match the experimental results within calibration error bars. The single-photon creation efficiency obtained in this work overcomes previous ion-cavity setups and is comparable to state-of-the-art systems composed of a neutral atom and a cavity operating in the strong coupling regime. (author)

Single-pass BPM system of the Photon Factory storage ring.

Science.gov (United States)

Honda, T; Katoh, M; Mitsuhashi, T; Ueda, A; Tadano, M; Kobayashi, Y

1998-05-01

At the 2.5 GeV ring of the Photon Factory, a single-pass beam-position monitor (BPM) system is being prepared for the storage ring and the beam transport line. In the storage ring, the injected beam position during the first several turns can be measured with a single injection pulse. The BPM system has an adequate performance, useful for the commissioning of the new low-emittance lattice. Several stripline BPMs are being installed in the beam transport line. The continuous monitoring of the orbit in the beam transport line will be useful for the stabilization of the injection energy as well as the injection beam orbit.

System requirements and design description for the document basis database interface (DocBasis)

International Nuclear Information System (INIS)

Lehman, W.J.

1997-01-01

This document describes system requirements and the design description for the Document Basis Database Interface (DocBasis). The DocBasis application is used to manage procedures used within the tank farms. The application maintains information in a small database to track the document basis for a procedure, as well as the current version/modification level and the basis for the procedure. The basis for each procedure is substantiated by Administrative, Technical, Procedural, and Regulatory requirements. The DocBasis user interface was developed by Science Applications International Corporation (SAIC)

A FIRST COMPARISON OF KEPLER PLANET CANDIDATES IN SINGLE AND MULTIPLE SYSTEMS

International Nuclear Information System (INIS)

Latham, David W.; Quinn, Samuel N.; Carter, Joshua A.; Holman, Matthew J.; Rowe, Jason F.; Borucki, William J.; Bryson, Stephen T.; Howell, Steve B.; Batalha, Natalie M.; Brown, Timothy M.; Buchhave, Lars A.; Caldwell, Douglas A.; Christiansen, Jessie L.; Ciardi, David R.; Cochran, William D.; Dunham, Edward W.; Fabrycky, Daniel C.; Ford, Eric B.; Gautier, Thomas N. III; Gilliland, Ronald L.

2011-01-01

In this Letter, we present an overview of the rich population of systems with multiple candidate transiting planets found in the first four months of Kepler data. The census of multiples includes 115 targets that show two candidate planets, 45 with three, eight with four, and one each with five and six, for a total of 170 systems with 408 candidates. When compared to the 827 systems with only one candidate, the multiples account for 17% of the total number of systems, and one-third of all the planet candidates. We compare the characteristics of candidates found in multiples with those found in singles. False positives due to eclipsing binaries are much less common for the multiples, as expected. Singles and multiples are both dominated by planets smaller than Neptune; 69 +2 -3 % for singles and 86 +2 -5 % for multiples. This result, that systems with multiple transiting planets are less likely to include a transiting giant planet, suggests that close-in giant planets tend to disrupt the orbital inclinations of small planets in flat systems, or maybe even prevent the formation of such systems in the first place.

Constraints for system specifications for the double-shell and single-shell tank systems

International Nuclear Information System (INIS)

SHAW, C.P.

1999-01-01

This is a supporting document for the Level 1 Double-Shell and Single-Shell System Specifications. The rationale for selection of specific regulatory constraining documents cited in the two system specifications is provided. many of the regulations have been implemented by the Project Hanford Management Contract procedures (HNF-PROs) and as such noted and traced back to their origins in State and Federal regulations

Constraints for system specifications for the double-shell and single-shell tank systems

Energy Technology Data Exchange (ETDEWEB)

SHAW, C.P.

1999-05-18

This is a supporting document for the Level 1 Double-Shell and Single-Shell System Specifications. The rationale for selection of specific regulatory constraining documents cited in the two system specifications is provided. many of the regulations have been implemented by the Project Hanford Management Contract procedures (HNF-PROs) and as such noted and traced back to their origins in State and Federal regulations.

A Structural Approach to Unresolved Mourning in Single Parent Family Systems.

Science.gov (United States)

Fulmer, Richard H.

1983-01-01

Considers the mother's depression as a special problem in therapy of single-parent families, resulting from unresolved mourning maintained by the family system. Offers reasons why the single-parent family's structure seems inherently vulnerable to unresolved mourning. Suggests techniques of Structural Family Therapy to facilitate mourning in such…

48 CFR 1852.214-70 - Caution to offerors furnishing descriptive literature.

Science.gov (United States)

2010-10-01

... furnishing descriptive literature. 1852.214-70 Section 1852.214-70 Federal Acquisition Regulations System... CLAUSES Texts of Provisions and Clauses 1852.214-70 Caution to offerors furnishing descriptive literature... Descriptive Literature (DEC 1988) Bidders are cautioned against furnishing as a part of their bids descriptive...

Crosswalking EAD: Collaboration in Archival Description

Directory of Open Access Journals (Sweden)

Amy McCrory

2005-09-01

Full Text Available Different library departments must work together, both formally and informally, in implementing encoded archival description and in repackaging descriptive information about archival collections to other formats, particularly machine-readable cataloging. The authors, one a technical services librarian and the other a special collections archivist, describe their experiences collaborating in these processes at The Ohio State University. Although other institutions may differ in their organizational structure, the authors hope to provide technical guidance, as well as a model of collaboration between archivists and technical services personnel. Careful dialogue and planning are essential to transcend the traditional divide between archival and library descriptive practices and systems.

Licensing systems and inspection of nuclear installations in NEA Member countries. Part 1, Description of licensing systems

International Nuclear Information System (INIS)

1977-01-01

This study provides an assessment of the legislative and regulatory provisions applicable and of the practices followed in the countries concerned and is divided into two separate sections. This document is the first part only. It contains the description of national licensing and inspection systems for nuclear installations in the twenty OECD countries which have specific regulations in this field. Each analysis has been presented following a plan which is as standardised as possible so as to facilitate comparison between the national systems. Part II, which is not included in this document, contains the diagrams illustrating the steps in the licensing procedure and the duties of the bodies involved as well as certain additional documents. It also includes a table showing the sequence of the main steps in the licensing process in the countries covered by this Study

A Descriptive Analysis of Decision Support Systems Research Between 1990 and 2003

Directory of Open Access Journals (Sweden)

David Arnott

2005-05-01

Full Text Available This paper is the first major report of a project that is investigating the theoretic foundations of decision support systems (DSS. The project was principally motivated by a concern for the direction and relevance of DSS research. The main areas of research focus are the decision and judgement theoretic base of the discipline, the research strategies used in published articles, and the professional relevance of DSS research. The project has analysed 926 DSS articles published in 14 major journals from 1990 to 2003. The findings indicate that DSS research is more dominated by positivist research than general information systems (in particular experiments, surveys, and descriptions of specific applications and systems, is heavily influenced by the work of Herbert Simon, is poorly grounded in contemporary judgement and decision-making research, and falls down in the identification of the nature of clients and users. Of great concern is the finding that DSS research has relatively low professional relevance. An overview of the direction of further analysis is presented.

Generating description with multi-feature fusion and saliency maps of image

Science.gov (United States)

Liu, Lisha; Ding, Yuxuan; Tian, Chunna; Yuan, Bo

2018-04-01

Generating description for an image can be regard as visual understanding. It is across artificial intelligence, machine learning, natural language processing and many other areas. In this paper, we present a model that generates description for images based on RNN (recurrent neural network) with object attention and multi-feature of images. The deep recurrent neural networks have excellent performance in machine translation, so we use it to generate natural sentence description for images. The proposed method uses single CNN (convolution neural network) that is trained on ImageNet to extract image features. But we think it can not adequately contain the content in images, it may only focus on the object area of image. So we add scene information to image feature using CNN which is trained on Places205. Experiments show that model with multi-feature extracted by two CNNs perform better than which with a single feature. In addition, we make saliency weights on images to emphasize the salient objects in images. We evaluate our model on MSCOCO based on public metrics, and the results show that our model performs better than several state-of-the-art methods.

Single-port laparoscopic myomectomy using a new single-port transumbilical morcellation system: initial clinical study.

Science.gov (United States)

Kim, Yong-Wook; Park, Byung-Joon; Ro, Duck-Yeong; Kim, Tae-Eung

2010-01-01

To evaluate the feasibility of single-port laparoscopic myomectomy with transumbilical morcellation and suturing. Continuing prospective study (Canadian Task Force classification II-3). University hospital. Fifteen patients who underwent single-port laparoscopic myomectomy between September 2008 and October 2009 to remove single or multiple uterine myomas, at least 1 in each patient measuring greater than 4 cm in diameter. All single-port laparoscopic myomectomy procedures were performed by a single surgeon (Dr. Y.W. Kim). Myomas were extracted transumbilically by cutting the myomas into smaller pieces with a knife or a conventional electromechanical morcellator. After making a single 1.5- to 2.0-cm umbilical incision, the single-port system, created with a wound retractor and a surgical glove, was inserted. All operations were performed using conventional rigid straight laparoscopic instruments. Laparoscopic suturing was performed in intramural myomas and some subserosal myomas. Patient mean (SD; range) age was 38.3 (5.6; 29-49) years. The number of myomas per patient was 1.6 (1.4; 1-6). The diameter of the largest myomas was 6.1 (1.5; 4.2-9.6) cm. In 4 patients, only a knife was required for transumbilical extraction of myomas, and in 11 patients, transumbilical morcellation with an electromechanical morcellator with or without a knife was used. Transumbilical drainage tubes were inserted into the pelvic cavity in 11 of 15 patients. Operative time was 96.7 (33.8; 35-150) minutes. The decrease in postoperative hemoglobin concentration was 1.8 (1.2; 0.4-3.6) g/dL. During the operations, no patients required blood transfusion. No patients developed postoperative fever. Neither bowel injury nor urinary tract injury occurred in any patient. The postoperative hospital stay was 3.1 (0.8; 2-4) days. Single-port transumbilical morcellation using a conventional electromechanical morcellator with or without a knife is feasible. Single-port laparoscopic myomectomy is an

Task-oriented control of Single-Master Multi-Slave Manipulator System

International Nuclear Information System (INIS)

Kosuge, Kazuhiro; Ishikawa, Jun; Furuta, Katsuhisa; Hariki, Kazuo; Sakai, Masaru.

1994-01-01

A master-slave manipulator system, in general, consists of a master arm manipulated by a human and a slave arm used for real tasks. Some tasks, such as manipulation of a heavy object, etc., require two or more slave arms operated simultaneously. A Single-Master Multi-Slave Manipulator System consists of a master arm with six degrees of freedom and two or more slave arms, each of which has six or more degrees of freedom. In this system, a master arm controls the task-oriented variables using Virtual Internal Model (VIM) based on the concept of 'Task-Oriented Control'. VIM is a reference model driven by sensory information and used to describe the desired relation between the motion of a master arm and task-oriented variables. The motion of slave arms are controlled based on the task oriented variables generated by VIM and tailors the system to meet specific tasks. A single-master multi-slave manipulator system, having two slave arms, is experimentally developed and illustrates the concept. (author)

Fill Rates of Single-Stage and Multistage Supply Systems

OpenAIRE

Matthew J. Sobel

2004-01-01

A supply system's fill rate is the fraction of demand that is met from on-hand inventory. This paper presents formulas for the fill rate of periodic review supply systems that use base-stock-level policies. The first part of the paper contains fill-rate formulas for a single-stage system and general distributions of demand. When demand is normally distributed, an exact expression uses only the standard normal distribution and density functions, and a good approximation uses only the standard ...

Macroscopic description of complex adaptive networks coevolving with dynamic node states

Science.gov (United States)

Wiedermann, Marc; Donges, Jonathan F.; Heitzig, Jobst; Lucht, Wolfgang; Kurths, Jürgen

2015-05-01

In many real-world complex systems, the time evolution of the network's structure and the dynamic state of its nodes are closely entangled. Here we study opinion formation and imitation on an adaptive complex network which is dependent on the individual dynamic state of each node and vice versa to model the coevolution of renewable resources with the dynamics of harvesting agents on a social network. The adaptive voter model is coupled to a set of identical logistic growth models and we mainly find that, in such systems, the rate of interactions between nodes as well as the adaptive rewiring probability are crucial parameters for controlling the sustainability of the system's equilibrium state. We derive a macroscopic description of the system in terms of ordinary differential equations which provides a general framework to model and quantify the influence of single node dynamics on the macroscopic state of the network. The thus obtained framework is applicable to many fields of study, such as epidemic spreading, opinion formation, or socioecological modeling.

Three-dimensional (3-D) video systems: bi-channel or single-channel optics?

Science.gov (United States)

van Bergen, P; Kunert, W; Buess, G F

1999-11-01

This paper presents the results of a comparison between two different three-dimensional (3-D) video systems, one with single-channel optics, the other with bi-channel optics. The latter integrates two lens systems, each transferring one half of the stereoscopic image; the former uses only one lens system, similar to a two-dimensional (2-D) endoscope, which transfers the complete stereoscopic picture. In our training centre for minimally invasive surgery, surgeons were involved in basic and advanced laparoscopic courses using both a 2-D system and the two 3-D video systems. They completed analog scale questionnaires in order to record a subjective impression of the relative convenience of operating in 2-D and 3-D vision, and to identify perceived deficiencies in the 3-D system. As an objective test, different experimental tasks were developed, in order to measure performance times and to count pre-defined errors made while using the two 3-D video systems and the 2-D system. Using the bi-channel optical system, the surgeon has a heightened spatial perception, and can work faster and more safely than with a single-channel system. However, single-channel optics allow the use of an angulated endoscope, and the free rotation of the optics relative to the camera, which is necessary for some operative applications.

Development of a Single-Axis Edge Detection System

Energy Technology Data Exchange (ETDEWEB)

Hanshaw, R.A.

2000-02-18

A SIP (Societe Genevoise d'Instruments de Physique) Trioptic coordinate measuring machine was modified for calibration of high quality single-axis glass standards to an uncertainty of {+-}0.000020 inch. The modification was accomplished through the addition of a frame grabber board, vision software, a high-resolution camera, stepper motors, a two-axis motor controller, and an HP-IB interface card. An existing temperature system (hygrometer, barometer, laser interferometer system, and optics) was retained as part of the system. An existing Hewlett Packard computer was replaced with a personal computer to accommodate the frame grabber board. Each component was integrated into the existing system using Visual Basic. The system was automated for unattended measurements by creating a machine programming language, which is recognized within the main program.

Multiple single-element transducer photoacoustic computed tomography system

Science.gov (United States)

Kalva, Sandeep Kumar; Hui, Zhe Zhi; Pramanik, Manojit

2018-02-01

Light absorption by the chromophores (hemoglobin, melanin, water etc.) present in any biological tissue results in local temperature rise. This rise in temperature results in generation of pressure waves due to the thermoelastic expansion of the tissue. In a circular scanning photoacoustic computed tomography (PACT) system, these pressure waves can be detected using a single-element ultrasound transducer (SUST) (while rotating in full 360° around the sample) or using a circular array transducer. SUST takes several minutes to acquire the PA data around the sample whereas the circular array transducer takes only a fraction of seconds. Hence, for real time imaging circular array transducers are preferred. However, these circular array transducers are custom made, expensive and not easily available in the market whereas SUSTs are cheap and readily available in the market. Using SUST for PACT systems is still cost effective. In order to reduce the scanning time to few seconds instead of using single SUST (rotating 360° ), multiple SUSTs can be used at the same time to acquire the PA data. This will reduce the scanning time by two-fold in case of two SUSTs (rotating 180° ) or by four-fold and eight-fold in case of four SUSTs (rotating 90° ) and eight SUSTs (rotating 45° ) respectively. Here we show that with multiple SUSTs, similar PA images (numerical and experimental phantom data) can be obtained as that of PA images obtained using single SUST.

Quantum logical description of microsystems

International Nuclear Information System (INIS)

Stachow, E.-W.

1984-01-01

An abstract object language with respect to single microsystems and its pragmatic foundation are considered in a systematic way. The quantum physical restrictions of local operations of a speaker lead to a propositional language which, under certain conditions, can be referred to an individual microsystem. The time dependence of the propositions according to the measuring process is discussed. Finally the language is extended to a space-time description of microsystems. Hereby relativity imposes certain constraints on the validi ty regions of propositions in space-time. Via realization, the language establishes the essential features of quantum physics in Hilbert space. (author)

Molecular acidity: An accurate description with information-theoretic approach in density functional reactivity theory.

Science.gov (United States)

Cao, Xiaofang; Rong, Chunying; Zhong, Aiguo; Lu, Tian; Liu, Shubin

2018-01-15

Molecular acidity is one of the important physiochemical properties of a molecular system, yet its accurate calculation and prediction are still an unresolved problem in the literature. In this work, we propose to make use of the quantities from the information-theoretic (IT) approach in density functional reactivity theory and provide an accurate description of molecular acidity from a completely new perspective. To illustrate our point, five different categories of acidic series, singly and doubly substituted benzoic acids, singly substituted benzenesulfinic acids, benzeneseleninic acids, phenols, and alkyl carboxylic acids, have been thoroughly examined. We show that using IT quantities such as Shannon entropy, Fisher information, Ghosh-Berkowitz-Parr entropy, information gain, Onicescu information energy, and relative Rényi entropy, one is able to simultaneously predict experimental pKa values of these different categories of compounds. Because of the universality of the quantities employed in this work, which are all density dependent, our approach should be general and be applicable to other systems as well. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Copenhagen's single system premise prevents a unified view of integer and fractional quantum Hall effect

CERN Document Server

Post, E J

1999-01-01

This essay presents conclusive evidence of the impermissibility of Copenhagen's single system interpretation of the Schroedinger process. The latter needs to be viewed as a tool exclusively describing phase and orientation randomized ensembles and is not be used for isolated single systems. Asymptotic closeness of single system and ensemble behavior and the rare nature of true single system manifestations have prevented a definitive identification of this Copenhagen deficiency over the past three quarter century. Quantum uncertainty so becomes a basic trade mark of phase and orientation disordered ensembles. The ensuing void of usable single system tools opens a new inquiry for tools without statistical connotations. Three, in part already known, period integrals here identified as flux, charge and action counters emerge as diffeo-4 invariant tools fully compatible with the demands of the general theory of relativity. The discovery of the quantum Hall effect has been instrumental in forcing a distinction betw...

Analyzing System on A Chip Single Event Upset Responses using Single Event Upset Data, Classical Reliability Models, and Space Environment Data

Science.gov (United States)

Berg, Melanie; LaBel, Kenneth; Campola, Michael; Xapsos, Michael

2017-01-01

We are investigating the application of classical reliability performance metrics combined with standard single event upset (SEU) analysis data. We expect to relate SEU behavior to system performance requirements. Our proposed methodology will provide better prediction of SEU responses in harsh radiation environments with confidence metrics. single event upset (SEU), single event effect (SEE), field programmable gate array devises (FPGAs)

Tore Supra: technical description

International Nuclear Information System (INIS)

1985-08-01

This report is aimed, after a brief recall of physics and technologic perspectives of Tore Supra, at giving a detailed description of the basic machine; details of each component are defined. Volume 1 is specifically concerned with the general aspects of Tore Supra and the toroidal field system [fr

Single-Frame Cinema. Three Dimensional Computer-Generated Imaging.

Science.gov (United States)

Cheetham, Edward Joseph, II

This master's thesis provides a description of the proposed art form called single-frame cinema, which is a category of computer imagery that takes the temporal polarities of photography and cinema and unites them into a single visual vignette of time. Following introductory comments, individual chapters discuss (1) the essential physical…

V and V of Lexical, Syntactic and Semantic Properties for Interactive Systems Through Model Checking of Formal Description of Dialog

Science.gov (United States)

Brat, Guillaume P.; Martinie, Celia; Palanque, Philippe

2013-01-01

During early phases of the development of an interactive system, future system properties are identified (through interaction with end users in the brainstorming and prototyping phase of the application, or by other stakehold-ers) imposing requirements on the final system. They can be specific to the application under development or generic to all applications such as usability principles. Instances of specific properties include visibility of the aircraft altitude, speed… in the cockpit and the continuous possibility of disengaging the autopilot in whatever state the aircraft is. Instances of generic properties include availability of undo (for undoable functions) and availability of a progression bar for functions lasting more than four seconds. While behavioral models of interactive systems using formal description techniques provide complete and unambiguous descriptions of states and state changes, it does not provide explicit representation of the absence or presence of properties. Assessing that the system that has been built is the right system remains a challenge usually met through extensive use and acceptance tests. By the explicit representation of properties and the availability of tools to support checking these properties, it becomes possible to provide developers with means for systematic exploration of the behavioral models and assessment of the presence or absence of these properties. This paper proposes the synergistic use two tools for checking both generic and specific properties of interactive applications: Petshop and Java PathFinder. Petshop is dedicated to the description of interactive system behavior. Java PathFinder is dedicated to the runtime verification of Java applications and as an extension dedicated to User Interfaces. This approach is exemplified on a safety critical application in the area of interactive cockpits for large civil aircrafts.

The LHCb RICH system; detector description and operation

Energy Technology Data Exchange (ETDEWEB)

Papanestis, A., E-mail: antonis.papanestis@stfc.ac.uk

2014-12-01

Two RICH detectors provide positive charged hadron identification in the LHCb experiment at the Large Hadron Collider at CERN. RICH 1 covers the full acceptance of the spectrometer and contains two radiators: aerogel and C{sub 4}F{sub 10}. RICH 2 covers half the acceptance and uses CF{sub 4} as a Cherenkov radiator. Photon detection is performed by the Hybrid Photon Detectors (HPDs), with silicon pixel sensors and bump-bonded readout encapsulated in a vacuum tube for efficient, low-noise single photon detection. The LHCb RICH detectors form a complex system of three radiators, 120 mirrors and 484 photon detectors operating in the very challenging environment of the LHC. The high performance of the system in pion and kaon identification in the momentum range of 2–100 GeV/c is reached only after careful calibration of many parameters. Operational efficiency above 99% was achieved by a high level of automatization in the operation of the detectors, from switching-on to error recovery. The challenges of calibrating and operating such a system will be presented. - Highlights: • This paper describes the operation and calibration of the LHCb RICH detectors. • The scintillation of CF{sub 4} was successfully suppressed with CO{sub 2}. • The refractive index of the gas radiators was calibrated with data to an accuracy better than 0.1%. • The Hybrid Photons Detectors were calibrated for operation in a magnetic field without loss of resolution.

Soft Biometrics; Human Identification Using Comparative Descriptions.

Science.gov (United States)

Reid, Daniel A; Nixon, Mark S; Stevenage, Sarah V

2014-06-01

Soft biometrics are a new form of biometric identification which use physical or behavioral traits that can be naturally described by humans. Unlike other biometric approaches, this allows identification based solely on verbal descriptions, bridging the semantic gap between biometrics and human description. To permit soft biometric identification the description must be accurate, yet conventional human descriptions comprising of absolute labels and estimations are often unreliable. A novel method of obtaining human descriptions will be introduced which utilizes comparative categorical labels to describe differences between subjects. This innovative approach has been shown to address many problems associated with absolute categorical labels-most critically, the descriptions contain more objective information and have increased discriminatory capabilities. Relative measurements of the subjects' traits can be inferred from comparative human descriptions using the Elo rating system. The resulting soft biometric signatures have been demonstrated to be robust and allow accurate recognition of subjects. Relative measurements can also be obtained from other forms of human representation. This is demonstrated using a support vector machine to determine relative measurements from gait biometric signatures-allowing retrieval of subjects from video footage by using human comparisons, bridging the semantic gap.

Electrochemistry and bioelectrochemistry towards the single-molecule level: Theoretical notions and systems

DEFF Research Database (Denmark)

Zhang, Jingdong; Chi, Qijin; Albrecht, Tim

2005-01-01

Surface structures controlled at the nanometer and single-molecule levels, with functions crucially determined by interfacial electron transfer (ET) are broadly reported in recent years, with different kinds of electrochemically controlled nanoscale/single molecule systems. One is the broad class...

Freeform surface descriptions. Part I: Mathematical representations

Science.gov (United States)

Broemel, Anika; Lippmann, Uwe; Gross, Herbert

2017-10-01

Optical systems can benefit strongly from freeform surfaces; however, the choice of the right surface representation is not trivial and many aspects must be considered. In this work, we discuss the general approach classical globally defined representations, as well as the basic mathematics and properties of the most commonly used descriptions and present a new description developed by us for describing freeform surfaces.

Apically extruded dentin debris by reciprocating single-file and multi-file rotary system.

Science.gov (United States)

De-Deus, Gustavo; Neves, Aline; Silva, Emmanuel João; Mendonça, Thais Accorsi; Lourenço, Caroline; Calixto, Camila; Lima, Edson Jorge Moreira

2015-03-01

This study aims to evaluate the apical extrusion of debris by the two reciprocating single-file systems: WaveOne and Reciproc. Conventional multi-file rotary system was used as a reference for comparison. The hypotheses tested were (i) the reciprocating single-file systems extrude more than conventional multi-file rotary system and (ii) the reciprocating single-file systems extrude similar amounts of dentin debris. After solid selection criteria, 80 mesial roots of lower molars were included in the present study. The use of four different instrumentation techniques resulted in four groups (n = 20): G1 (hand-file technique), G2 (ProTaper), G3 (WaveOne), and G4 (Reciproc). The apparatus used to evaluate the collection of apically extruded debris was typical double-chamber collector. Statistical analysis was performed for multiple comparisons. No significant difference was found in the amount of the debris extruded between the two reciprocating systems. In contrast, conventional multi-file rotary system group extruded significantly more debris than both reciprocating groups. Hand instrumentation group extruded significantly more debris than all other groups. The present results yielded favorable input for both reciprocation single-file systems, inasmuch as they showed an improved control of apically extruded debris. Apical extrusion of debris has been studied extensively because of its clinical relevance, particularly since it may cause flare-ups, originated by the introduction of bacteria, pulpal tissue, and irrigating solutions into the periapical tissues.

Control algorithms for single inverter dual induction motor system applied to railway traction; Commande algorithmique d'un systeme mono-onduleur bimachine asynchrone destine a la traction ferroviaire

Energy Technology Data Exchange (ETDEWEB)

Pena Eguiluz, R.

2002-11-15

The goal of this work concerns the modelling and the behaviour characterisation of a single inverter dual induction motor system applied to a railway traction bogie (BB36000) in order to concept its control. First part of this job is dedicated to the detailed description of overall system. The influence analysis of the internal perturbations (motor parameters variation) and, external perturbations (pantograph detachment, adherence loss, stick-slip) of the system have made considering the field oriented control applied to each motor of the bogie (classical traction structure). vi In a second part, a novel propulsion structure is proposed. It is composed by a single pulse-width modulated two level voltage source inverter. It supplies two parallel connected induction motors, which generate the transmitted traction force to the bogie wheels. The locomotive case represents the common load for the two motors. Several co-operative control strategies (CS) are studied. They are: the mean CS, the double mean CS, the master - slave switched CS and, the mean differential CS. In addition, an appropriated electric modes observer structure for these different controls has studied. These controls have validated applying the perturbations to the models using the solver SABER. This special approach is equivalent to quasi-experimentation, because the mechanical and the electrical system components have modelled using MAST language and, the sample control has created by a C code programme in the SABER environment. Third part is dedicated to the mechanical sensor suppression and, its adaptation in the cooperative control strategies. The partial speed reconstruction methods are: the fundamental frequency relation, the mechanical Kalman filter, the variable structure observer and the MRAS. Finally, the hardware system configuration of the experimental realisation is described. (author)

A New Power Calculation Method for Single-Phase Grid-Connected Systems

DEFF Research Database (Denmark)

Yang, Yongheng; Blaabjerg, Frede

2013-01-01

A new method to calculate average active power and reactive power for single-phase systems is proposed in this paper. It can be used in different applications where the output active power and reactive power need to be calculated accurately and fast. For example, a grid-connected photovoltaic...... system in low voltage ride through operation mode requires a power feedback for the power control loop. Commonly, a Discrete Fourier Transform (DFT) based power calculation method can be adopted in such systems. However, the DFT method introduces at least a one-cycle time delay. The new power calculation...... method, which is based on the adaptive filtering technique, can achieve a faster response. The performance of the proposed method is verified by experiments and demonstrated in a 1 kW single-phase grid-connected system operating under different conditions.Experimental results show the effectiveness...

Compact teleoperated laparoendoscopic single-site robotic surgical system: Kinematics, control, and operation.

Science.gov (United States)

Isaac-Lowry, Oran Jacob; Okamoto, Steele; Pedram, Sahba Aghajani; Woo, Russell; Berkelman, Peter

2017-12-01

To date a variety of teleoperated surgical robotic systems have been developed to improve a surgeon's ability to perform demanding single-port procedures. However typical large systems are bulky, expensive, and afford limited angular motion, while smaller designs suffer complications arising from limited motion range, speed, and force generation. This work was to develop and validate a simple, compact, low cost single site teleoperated laparoendoscopic surgical robotic system, with demonstrated capability to carry out basic surgical procedures. This system builds upon previous work done at the University of Hawaii at Manoa and includes instrument and endoscope manipulators as well as compact articulated instruments designed to overcome single incision geometry complications. A robotic endoscope holder was used for the base, with an added support frame for teleoperated manipulators and instruments fabricated mostly from 3D printed parts. Kinematics and control methods were formulated for the novel manipulator configuration. Trajectory following results from an optical motion tracker and sample task performance results are presented. Results indicate that the system has successfully met the goal of basic surgical functionality while minimizing physical size, complexity, and cost. Copyright © 2017 John Wiley & Sons, Ltd.

Descriptive scientific analysis: progress of the educational system of Saudi Arabia

Directory of Open Access Journals (Sweden)

Annemarie PROFANTER

2017-06-01

Full Text Available Saudi Arabia has set itself the goal of developing a knowledge-based society. Demographic changes and economic growth within short time in the Kingdom of Saudi Arabia led to radical changes of the educational system. Higher education institutions are in expansion and international collaborations are being intensified. The policy of gender segregation based on a neopatriarchal society favored by the tribal system is an important cultural element of Saudi society and influences the Saudi educational culture.This article provides a scientific description and analyzes the main elements of the Saudi higher education system using the few data available due to the limited release of official statistics. Prince Mohammad Bin Fahd University is analyzed as a case study based on the author’s experience who taught there as an academic years of 2006 and 2008. Being the first private institution to admit both male and female students it had to face several challenges. Furthermore, the impact of international collaborations is identified by exploring the «King Abdullah Scholarship Programme» which gives thousands of students the opportunity to study abroad.Education while having a global function also fulfills a national function. Therefore, collaborations with Western universities in the Kingdom have created challenges for the recent generations in balancing Western values imposed throughout their higher education with their traditional culture. Due to the policy of gender segregation, the Saudi educational system represents different obstructions and opportunities particularly for female students.

Descriptive Research

DEFF Research Database (Denmark)

Wigram, Anthony Lewis

2003-01-01

Descriptive research is described by Lathom-Radocy and Radocy (1995) to include Survey research, ex post facto research, case studies and developmental studies. Descriptive research also includes a review of the literature in order to provide both quantitative and qualitative evidence of the effect...... starts will allow effect size calculations to be made in order to evaluate effect over time. Given the difficulties in undertaking controlled experimental studies in the creative arts therapies, descriptive research methods offer a way of quantifying effect through descriptive statistical analysis...

Pseudo-Hermitian description of PT-symmetric systems defined on a complex contour

International Nuclear Information System (INIS)

Mostafazadeh, Ali

2005-01-01

We describe a method that allows for a practical application of the theory of pseudo-Hermitian operators to PT-symmetric systems defined on a complex contour. We apply this method to study the Hamiltonians H = p 2 + x 2 (ix) ν with ν ε (-2, ∞) that are defined along the corresponding anti-Stokes lines. In particular, we reveal the intrinsic non-Hermiticity of H for the cases that ν is an even integer, so that H p 2 ± x 2+ν , and give a proof of the discreteness of the spectrum of H for all ν ε (-2, ∞). Furthermore, we study the consequences of defining a square-well Hamiltonian on a wedge-shaped complex contour. This yields a PT-symmetric system with a finite number of real eigenvalues. We present a comprehensive analysis of this system within the framework of pseudo-Hermitian quantum mechanics. We also outline a direct pseudo-Hermitian treatment of PT-symmetric systems defined on a complex contour which clarifies the underlying mathematical structure of the formulation of PT-symmetric quantum mechanics based on the charge-conjugation operator. Our results provide conclusive evidence that pseudo-Hermitian quantum mechanics provides a complete description of general PT-symmetric systems regardless of whether they are defined along the real line or a complex contour

Development of elemental technique for single particle irradiation system to cell

International Nuclear Information System (INIS)

Yukawa, Masae; Yasuda, Nakahiro; Matsumoto, Kenichi

2004-01-01

A single-ion microbeam facility (SPICE: Single Particle Irradiation system to Cell) are constructing at National Institute of Radiological Sciences (NIRS). The system was design to deliver the defined number of helium or hydrogen ions into an area smaller than the nuclei of cells in culture on thin films. The beam will be focused into 2μmθ (in diameter) by triplet-Q magnet. We have established the monitoring system using thin plastic scintillator, IIT and charge-coupled device (CCD) camera to measure the size and position of microbeam. The monitoring system for microbeam has been evaluated in the middle energy course using 4.3 MeV protons. We have designed and made two new type collimators to get the microbeam, and have evaluated its scattering effect. We have confirmed that the collimated beam spot (100 ions/sec) was observed in CCD image as small light spot. This system is now installed into SPICE apparatus. (authors)

Single-mode optical fibres

CERN Document Server

Cancellieri, G

1991-01-01

This book describes signal propagation in single-mode optical fibres for telecommunication applications. Such description is based on the analysis of field propagation, considering waveguide properties and also some of the particular characteristics of the material fibre. The book covers such recent advances as, coherent transmissions; optical amplification; MIR fibres; polarization maintaining; polarization diversity and photon counting.

XML Diagnostics Description Standard

International Nuclear Information System (INIS)

Neto, A.; Fernandes, H.; Varandas, C.; Lister, J.; Yonekawa, I.

2006-01-01

A standard for the self-description of fusion plasma diagnostics will be presented, based on the Extensible Markup Language (XML). The motivation is to maintain and organise the information on all the components of a laboratory experiment, from the hardware to the access security, to save time and money when problems arises. Since there is no existing standard to organise this kind of information, every Association stores and organises each experiment in different ways. This can lead to severe problems when the organisation schema is poorly documented or written in national languages. The exchange of scientists, researchers and engineers between laboratories is a common practice nowadays. Sometimes they have to install new diagnostics or to update existing ones and frequently they lose a great deal of time trying to understand the currently installed system. The most common problems are: no documentation available; the person who understands it has left; documentation written in the national language. Standardisation is the key to solving all the problems mentioned. From the commercial information on the diagnostic (component supplier; component price) to the hardware description (component specifications; drawings) to the operation of the equipment (finite state machines) through change control (who changed what and when) and internationalisation (information at least in the native language and in English), a common XML schema will be proposed. This paper will also discuss an extension of these ideas to the self-description of ITER plant systems, since the problems will be identical. (author)

Single-phase multi-dimensional thermohydraulics direct numerical simulation code DINUS-3. Input data description

Energy Technology Data Exchange (ETDEWEB)

Muramatsu, Toshiharu [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center

1998-08-01

This report explains the numerical methods and the set-up method of input data for a single-phase multi-dimensional thermohydraulics direct numerical simulation code DINUS-3 (Direct Numerical Simulation using a 3rd-order upwind scheme). The code was developed to simulate non-stationary temperature fluctuation phenomena related to thermal striping phenomena, developed at Power Reactor and Nuclear Fuel Development Corporation (PNC). The DINUS-3 code was characterized by the use of a third-order upwind scheme for convection terms in instantaneous Navier-Stokes and energy equations, and an adaptive control system based on the Fuzzy theory to control time step sizes. Author expect this report is very useful to utilize the DINUS-3 code for the evaluation of various non-stationary thermohydraulic phenomena in reactor applications. (author)

Neural systems language: a formal modeling language for the systematic description, unambiguous communication, and automated digital curation of neural connectivity.

Science.gov (United States)

Brown, Ramsay A; Swanson, Larry W

2013-09-01

Systematic description and the unambiguous communication of findings and models remain among the unresolved fundamental challenges in systems neuroscience. No common descriptive frameworks exist to describe systematically the connective architecture of the nervous system, even at the grossest level of observation. Furthermore, the accelerating volume of novel data generated on neural connectivity outpaces the rate at which this data is curated into neuroinformatics databases to synthesize digitally systems-level insights from disjointed reports and observations. To help address these challenges, we propose the Neural Systems Language (NSyL). NSyL is a modeling language to be used by investigators to encode and communicate systematically reports of neural connectivity from neuroanatomy and brain imaging. NSyL engenders systematic description and communication of connectivity irrespective of the animal taxon described, experimental or observational technique implemented, or nomenclature referenced. As a language, NSyL is internally consistent, concise, and comprehensible to both humans and computers. NSyL is a promising development for systematizing the representation of neural architecture, effectively managing the increasing volume of data on neural connectivity and streamlining systems neuroscience research. Here we present similar precedent systems, how NSyL extends existing frameworks, and the reasoning behind NSyL's development. We explore NSyL's potential for balancing robustness and consistency in representation by encoding previously reported assertions of connectivity from the literature as examples. Finally, we propose and discuss the implications of a framework for how NSyL will be digitally implemented in the future to streamline curation of experimental results and bridge the gaps among anatomists, imagers, and neuroinformatics databases. Copyright © 2013 Wiley Periodicals, Inc.

Benefits of a single payment system: case study of Abu Dhabi health system reforms.

Science.gov (United States)

Vetter, Philipp; Boecker, Klaus

2012-12-01

In 2005 leaders in the wealthy Emirate of Abu Dhabi inherited an health system from their predecessors that was well-intentioned in its historic design, but that did not live up to aspirations in any dimension. First, the Emirate defined a vision to deliver "world-class" quality care in response to citizen's needs. It has since introduced tiered mandatory health insurance for all inhabitants linked to a single standard payment system, which generates accurate data as an invaluable by-product. A newly created independent health system regulator monitors these data and licenses, audits, and inspects all health service professionals, facilities, and insurers accordingly. We analyse these health system reforms using the "Getting Health Reform Right" framework. Our analysis suggests that an integrated set of reforms addressing all reform levers is critical to achieving the outcomes observed. The reform programme has improved access, by giving all residents health cards. The approximate doubling of demand has been matched by flexible supply, with the private sector adding 5 new hospitals and 93 clinics to the health system infrastructure since 2006. The focus on reliable raw-data flows through the single standard payment system functions as a motor for improvement services, innovation, and investment, for instance by allowing payers to 'pay for quality', which may well be applicable in other contexts. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

SADE: system of acquisition of experimental data. Definition and analysis of an experiment description language

International Nuclear Information System (INIS)

Gagniere, Jean-Michel

1983-01-01

This research thesis presents a computer system for the acquisition of experimental data. It is aimed at acquiring, at processing and at storing information from particle detectors. The acquisition configuration is described by an experiment description language. The system comprises a lexical analyser, a syntactic analyser, a translator, and a data processing module. It also comprises a control language and a statistics management and plotting module. The translator builds up series of tables which allow, during an experiment, different sequences to be executed: experiment running, calculations to be performed on this data, building up of statistics. Short execution time and ease of use are always looked for [fr

A Transformer-less Single Phase Inverter For photovoltaic Systems

DEFF Research Database (Denmark)

Mostaan, Ali; Alizadeh, Ebrahim; Qu, Ying

2017-01-01

A single phase transformer-less inverter is introduced in this paper. The negative polarities of the input voltage and output terminal have common ground. Therefore, the leakage current problem that is common in PV systems is eliminated naturally. In addition, the proposed inverter has fewer comp...

Nuclear computerized library for assessing reactor reliability (NUCLARR): User's guide: Part 3, NUCLARR system description

International Nuclear Information System (INIS)

Gilmore, W.E.; Gentillon, C.D.; Gertman, D.I.; Beers, G.H.; Galyean, W.J.; Gilbert, B.G.

1988-06-01

The Nuclear Computerized Library for Assessing Reactor Reliability (NUCLARR) is an automated data base management system for processing and storing human error probability and hardware component failure data. The NUCLARR system software resides on an IBM (or compatible) personal micro-computer. NUCLARR can be used by the end user to furnish data inputs for both human and hardware reliability analysis in support of a variety of risk assessment activities. The NUCLARR system is documented in a five-volume series of reports. Volume IV of this series is the User's Guide for operating the NUCLARR software and is presented in three parts. This document, Part 3: NUCLARR System Description, provides an in-depth discussion of the design characteristics and special features of the NUCLARR software. Part 3 also presents the organization of the data base structures and techniques used to manipulate the data

Robot-assisted single port radical nephrectomy and cholecystectomy: description and technical aspects.

Science.gov (United States)

Mota Filho, Francisco Hidelbrando Alves; Sávio, Luis Felipe; Sakata, Rafael Eiji; Ivanovic, Renato Fidelis; da Silva, Marco Antonio Nunes; Maia, Ronaldo; Passerotti, Carlo

2018-01-01

Robot-Assisted Single Site Radical Nephrectomy (RASS-RN) has been reported by surgeons in Europe and United States (1-3). To our best knowledge this video presents the first RASS-RN with concomitant cholecystectomy performed in Latin America. A 66 year-old renal transplant male due to chronic renal failure presented with an incidental 1.3cm nodule in the upper pole of the right kidney. In addition, symptomatic gallbladder stones were detected. Patient was placed in modified flank position. Multichannel single port device was placed using Hassan's technique through a 3cm supra-umbilical incision. Standard radical nephrectomy and cholecystectomy were made using na 8.5mm camera, two 5mm robotic arms and an assistant 5mm access. Surgery time and estimated blood loss were 208 minutes and 100mL, respectively. Patient did well and was discharged within less than 48 hours, without complications. Pathology report showed benign renomedullary tumor of interstitial cells and chronic cholecystitis. Robotic technology improves ergonomics, gives better precision and enhances ability to approach complex surgeries. Robot-assisted Single Port aims to reduce the morbidity of multiple trocar placements while maintaining the advantages of robotic surgery (2). Limitations include the use of semi-rigid instruments providing less degree of motion and limited space leading to crash between instruments. On the other hand, it is possible to perform complex and concomitant surgeries with just one incision. RASS-RN seems to be safe and feasible option for selected cases. Studies should be performed to better understand the results using single port technique in Urology. Copyright® by the International Brazilian Journal of Urology.

Robot-assisted single port radical nephrectomy and cholecystectomy: description and technical aspects

Directory of Open Access Journals (Sweden)

Francisco Hidelbrando Alves Mota Filho

Full Text Available ABSTRACT Introduction Robot-Assisted Single Site Radical Nephrectomy (RASS-RN has been reported by surgeons in Europe and United States (1–3. To our best knowledge this video presents the first RASS-RN with concomitant cholecystectomy performed in Latin America. Case A 66 year-old renal transplant male due to chronic renal failure presented with an incidental 1.3cm nodule in the upper pole of the right kidney. In addition, symptomatic gallbladder stones were detected. Results Patient was placed in modified flank position. Multichannel single port device was placed using Hassan's technique through a 3 cm supra-umbilical incision. Standard radical nephrectomy and cholecystectomy were made using an 8.5mm camera, two 5mm robotic arms and an assistant 5mm access. Surgery time and estimated blood loss were 208 minutes and 100mL, respectively. Patient did well and was discharged within less than 48 hours, without complications. Pathology report showed benign renomedullary tumor of interstitial cells and chronic cholecystitis. Discussion Robotic technology improves ergonomics, gives better precision and enhances ability to approach complex surgeries. Robot-assisted Single Port aims to reduce the morbidity of multiple trocar placements while maintaining the advantages of robotic surgery (2. Limitations include the use of semi-rigid instruments providing less degree of motion and limited space leading to crash between instruments. On the other hand, it is possible to perform complex and concomitant surgeries with just one incision. Conclusion RASS-RN seems to be safe and feasible option for selected cases. Studies should be performed to better understand the results using single port technique in Urology.

A model-independent description of few-body system with strong interaction

International Nuclear Information System (INIS)

Simenog, I.V.

1985-01-01

In this contribution, the authors discuss the formulation of equations that provide model-independent description of systems of three and more nucleons irrespective of the details of the interaction, substantiate the approach, estimate the correction terms with respect to the force range, and give basic qualitative results obtained by means of the model-independent procedure. They consider three nucleons in the doublet state (spin S=I/2) taking into account only S-interaction. The elastic nd-scattering amplitude may be found from the model-independent equations that follow from the Faddeev equations in the short-range-force limit. They note that the solutions of several model-independent equations and basic results obtained with the use of this approach may serve both as a standard solution and starting point in the discussion of various conceptions concerning the details of nuclear interactions

Factors associated with anxiety and depression among type 2 diabetes outpatients in Malaysia: a descriptive cross-sectional single-centre study.

Science.gov (United States)

Ganasegeran, Kurubaran; Renganathan, Pukunan; Manaf, Rizal Abdul; Al-Dubai, Sami Abdo Radman

2014-04-23

To determine the prevalence and factors associated with anxiety and depression among type 2 diabetes outpatients in Malaysia. Descriptive, cross-sectional single-centre study with universal sampling of all patients with type 2 diabetes. Endocrinology clinic of medical outpatient department in a Malaysian public hospital. All 169 patients with type 2 diabetes (men, n=99; women, n=70) aged between 18 and 90 years who acquired follow-up treatment from the endocrinology clinic in the month of September 2013. The validated Hospital Anxiety and Depression Scale (HADS), sociodemographic characteristics and clinical health information from patient records. Of the total 169 patients surveyed, anxiety and depression were found in 53 (31.4%) and 68 (40.3%), respectively. In multivariate analysis, age, ethnicity and ischaemic heart disease were significantly associated with anxiety, while age, ethnicity and monthly household income were significantly associated with depression. Sociodemographics and clinical health factors were important correlates of anxiety and depression among patients with diabetes. Integrated psychological and medical care to boost self-determination and confidence in the management of diabetes would catalyse optimal health outcomes among patients with diabetes.

Single event monitoring system based on Java 3D and XML data binding

International Nuclear Information System (INIS)

Wang Liang; Chinese Academy of Sciences, Beijing; Zhu Kejun; Zhao Jingwei

2007-01-01

Online single event monitoring is important to BESIII DAQ System. Java3D is extension of Java Language in 3D technology, XML data binding is more efficient to handle XML document than SAX and DOM. This paper mainly introduce the implementation of BESIII single event monitoring system with Java3D and XML data binding, and interface for track fitting software with JNI technology. (authors)

Description of the PMAD DC test bed architecture and integration sequence

Science.gov (United States)

Beach, R. F.; Trash, L.; Fong, D.; Bolerjack, B.

1991-01-01

NASA-LEWIS is responsible for the development, fabrication, and assembly of the electric power system (EPS) for the Space Station Freedom (SSF). The SSF power system is radically different from previous spacecraft power systems in both the size and complexity of the system. Unlike past spacecraft power systems, the SSF EPS will grow and be maintained on orbit and must be flexible to meet challenging user power needs. The SSF power system is also unique in comparison with terrestrial power systems because it is dominated by power electronic converters which regulate and control the power. A description is provided of the Power Management and Distribution DC Testbed which was assembled to support the design and early evaluation of the SSF EPS. A description of the integration process used in the assembly sequence is also given along with a description of the support facility.

Graphic Description: The Mystery of Ibn Khafaja\\'s Success in Description

Directory of Open Access Journals (Sweden)

جواد رنجبر

2009-12-01

Full Text Available Graphic Description:   The Mystery of Ibn Khafaja's Success in Description    Ali Bagher Taheriniya *  Javad Ranjbar **      Abstract Ibn Khafaja is one of the poets and men of letters in Spain. He is titled to Sanobari of Spain. He is one of the masters of description. Hence, the analysis of successful techniques he has used in the descriptive art could illuminate the way for others. Al-Taswir al-harfi (graphic description is a term which denotes the highest and most detailed poems. On this basis, the best descriptive poem is one which is closer to a painting. He has used some elements called conforming elements of description which contain: imagination, feeling, faculty, and dialogue as well as three other elements: to be inborn in description, enchanting nature and convenient life. This article is going to give an analysis of the reasons for Ibn Khafaja’s success in description and portrait making.   Key words: Ibn Khafaja, poetry, description, portrait   * Associate Professor, Bu Ali Sina University of Hamadan E-mail: bTaheriniya@yahoo.com  ** M.A. in Arabic Language and Literature

THULE: A detailed description

International Nuclear Information System (INIS)

Terry, M.J.

1964-07-01

This report describes the THULE scheme of lattice physics calculation which has been developed in FORTRAN for the IBM 7090. This scheme predicts the neutron flux over energy and space, for many groups and regions, together with reactivity and reaction rate edits for both a single lattice cell and a reactor core. This report describes in detail the input requirements for the THULE programme which forms the main part of the scheme. Brief descriptions of the 7090 programmes TED 6 and NOAH are included as appendices. TED 6 will produce the THULE edits from a WDSN output tape and NOAH is a version of the METHUSELAH programme which contains many of the THULE edits and will also produce input cards for THULE. (author)

Descriptive review of tuberculosis surveillance systems across the circumpolar regions

Directory of Open Access Journals (Sweden)

Annie-Claude Bourgeois

2016-04-01

baseline knowledge on similarities and differences among circumpolar tuberculosis surveillance systems. The similarity in case definitions will allow for description of the epidemiology of TB based on surveillance data in circumpolar regions, further study of tuberculosis trends across regions, and recommendation of best practices to improve surveillance activities.

Upgrade of the MAGIC telescopes single wavelength micro power LIDAR system

Energy Technology Data Exchange (ETDEWEB)

Mueller, Dominik [Max-Planck-Institut fuer Physik, Muenchen (Germany); Collaboration: MAGIC-Collaboration

2016-07-01

Since 2011 a single wavelength LIDAR system is operated alongside the observations of the MAGIC telescopes. It is used for real-time monitoring of the atmospheric transmission and for detecting cloud layers within the field of view of MAGIC. The system uses a pulsed Nd:YAG laser with 532 nm wavelength and a pulse energy of 5 μJ as transmitter. The receiver is mounted to a 60 cm spherical single mirror telescope with a F/D ratio of 2.5. To compensate for the low light intensities a sensitive detector with the capability of single photon detection as well as charge integration is needed. For this purpose, a hybrid photo diode with a peak quantum efficiency of 55% an a pulse width of 2.5ns is used in a custom designed detector. The analog signal is recorded by a computer mounted 8-bit FADC with 200 MS/s. A signal analysis algorithm converts the LIDAR return signal into a number of single photoelectron counts per range bin. The atmospheric transmission is calculated by fitting a Rayleigh back-scattering model with a sliding window. The resulting transmission profile is used to correct the MAGIC gamma ray data for adverse weather conditions. After five years of data taking the MAGIC LIDAR system is upgraded with a stronger laser and a new detector unit in order to extend the measurement range and to optimize the operation.

Is Bare Band Description of Carrier Transport Appropriate in Pentacene?

Science.gov (United States)

Andersen, John D.; Giuggioli, Luca; Kenkre, V. M.

2002-03-01

Experiments on injected charges in pentacene single crystals reveal mobilities typical of inorganic semiconductors and temperature dependence (for TSchein, C. B. Duke, and A.R. McGhie, Phys. Rev. Lett. 40, 197 (1978); L. B. Schein, W. Warta, and N. Karl, Chem. Phys. Lett. 100, 34 (1983)) Because the low temperature mobility values in pentacene suggest moderately large bandwidths, we address two questions. Does a bare wide (effectively infinite) band description work for pentacene for T<400K? And, is a bare finite band description compatible with those data? These questions are answered by modifications of a theory originally constructed for inorganic materials and a newly developed mobility theory.

Description of recommended non-thermal mixed waste treatment technologies: Version 1.0

International Nuclear Information System (INIS)

1995-08-01

This document contains description of the technologies selected for inclusions in the Integrated Nonthermal Treatment Systems (INTS) Study. The purpose of these descriptions is to provide a more complete description of the INTS technologies. It supplements the summary descriptions of candidate nonthermal technologies that were considered for the INTS

Description of recommended non-thermal mixed waste treatment technologies: Version 1.0

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

This document contains description of the technologies selected for inclusions in the Integrated Nonthermal Treatment Systems (INTS) Study. The purpose of these descriptions is to provide a more complete description of the INTS technologies. It supplements the summary descriptions of candidate nonthermal technologies that were considered for the INTS.

An Efficient Explicit-time Description Method for Timed Model Checking

Directory of Open Access Journals (Sweden)

Hao Wang

2009-12-01

Full Text Available Timed model checking, the method to formally verify real-time systems, is attracting increasing attention from both the model checking community and the real-time community. Explicit-time description methods verify real-time systems using general model constructs found in standard un-timed model checkers. Lamport proposed an explicit-time description method using a clock-ticking process (Tick to simulate the passage of time together with a group of global variables to model time requirements. Two methods, the Sync-based Explicit-time Description Method using rendezvous synchronization steps and the Semaphore-based Explicit-time Description Method using only one global variable were proposed; they both achieve better modularity than Lamport's method in modeling the real-time systems. In contrast to timed automata based model checkers like UPPAAL, explicit-time description methods can access and store the current time instant for future calculations necessary for many real-time systems, especially those with pre-emptive scheduling. However, the Tick process in the above three methods increments the time by one unit in each tick; the state spaces therefore grow relatively fast as the time parameters increase, a problem when the system's time period is relatively long. In this paper, we propose a more efficient method which enables the Tick process to leap multiple time units in one tick. Preliminary experimental results in a high performance computing environment show that this new method significantly reduces the state space and improves both the time and memory efficiency.

Characteristics of electromagnetic forces of a single winding EDS MAGLEV system

Energy Technology Data Exchange (ETDEWEB)

Hong, Soon Heum [Korea High Speed Rail Construction Authority (Korea, Republic of); Cha, Guee Soo [Seoul National University (Korea, Republic of); Hahn, Song Yop [Soonchunhyang University (Korea, Republic of)

1995-07-01

This paper describes the characteristics of electromagnetic forces of Combined superconducting maglev system. Generation of the levitation, the propulsion and the guidance force by a single coil is proved by the phasor analysis. It is also shown that double-layered configuration has better characteristics in efficiency, pulsation of the forces and drag ration than single-layered configuration. (author). 3 refs., 7 figs., 1 tab.

A Formal Semantics for Concept Understanding relying on Description Logics

DEFF Research Database (Denmark)

Badie, Farshad

2017-01-01

In this research, Description Logics (DLs) will be employed for logical description, logical characterisation, logical modelling and ontological description of concept understanding in terminological systems. It’s strongly believed that using a formal descriptive logic could support us in reveali...... logical assumptions whose discovery may lead us to a better understanding of ‘concept understanding’. The Structure of Observed Learning Outcomes (SOLO) model as an appropriate model of increasing complexity of humans’ understanding has supported the formal analysis....

A Formal Semantics for Concept Understanding relying on Description Logics

DEFF Research Database (Denmark)

Badie, Farshad

2017-01-01

logical assumptions whose discovery may lead us to a better understanding of ‘concept understanding’. The Structure of Observed Learning Outcomes (SOLO) model as an appropriate model of increasing complexity of humans’ understanding has supported the formal analysis.......In this research, Description Logics (DLs) will be employed for logical description, logical characterisation, logical modelling and ontological description of concept understanding in terminological systems. It’s strongly believed that using a formal descriptive logic could support us in revealing...

Simple test system for single molecule recognition force microscopy

International Nuclear Information System (INIS)

Riener, Christian K.; Stroh, Cordula M.; Ebner, Andreas; Klampfl, Christian; Gall, Alex A.; Romanin, Christoph; Lyubchenko, Yuri L.; Hinterdorfer, Peter; Gruber, Hermann J.

2003-01-01

We have established an easy-to-use test system for detecting receptor-ligand interactions on the single molecule level using atomic force microscopy (AFM). For this, avidin-biotin, probably the best characterized receptor-ligand pair, was chosen. AFM sensors were prepared containing tethered biotin molecules at sufficiently low surface concentrations appropriate for single molecule studies. A biotin tether, consisting of a 6 nm poly(ethylene glycol) (PEG) chain and a functional succinimide group at the other end, was newly synthesized and covalently coupled to amine-functionalized AFM tips. In particular, PEG 800 diamine was glutarylated, the mono-adduct NH 2 -PEG-COOH was isolated by ion exchange chromatography and reacted with biotin succinimidylester to give biotin-PEG-COOH which was then activated as N-hydroxysuccinimide (NHS) ester to give the biotin-PEG-NHS conjugate which was coupled to the aminofunctionalized AFM tip. The motional freedom provided by PEG allows for free rotation of the biotin molecule on the AFM sensor and for specific binding to avidin which had been adsorbed to mica surfaces via electrostatic interactions. Specific avidin-biotin recognition events were discriminated from nonspecific tip-mica adhesion by their typical unbinding force (∼40 pN at 1.4 nN/s loading rate), unbinding length (<13 nm), the characteristic nonlinear force-distance relation of the PEG linker, and by specific block with excess of free d-biotin. The convenience of the test system allowed to evaluate, and compare, different methods and conditions of tip aminofunctionalization with respect to specific binding and nonspecific adhesion. It is concluded that this system is well suited as calibration or start-up kit for single molecule recognition force microscopy

Diffusion-cooled high-power single-mode waveguide CO2 laser for transmyocardial revascularization

Science.gov (United States)

Berishvili, I. I.; Bockeria, L. A.; Egorov, E. N.; Golubev, Vladimir S.; Galushkin, Michail G.; Kheliminsky, A. A.; Panchenko, Vladislav Y.; Roshin, A. P.; Sigaev, I. Y.; Vachromeeva, M. N.; Vasiltsov, Victor V.; Yoshina, V. I.; Zabelin, Alexandre M.; Zelenov, Evgenii V.

1999-01-01

The paper presents the results on investigations and development of multichannel waveguide CO2 laser with diffusion cooling of active medium excited by discharge of audio-frequency alternating current. The description of high-power single-mode CO2 laser with average beam power up to 1 kW is presented. The result of measurement of the laser basic parameters are offered, as well as the outcomes of performances of the laser head with long active zone, operating in waveguide mode. As an example of application of these laser, various capabilities a description of the developed medical system 'Genom' used in the transmyocardial laser revascularization (TMLR) procedure and clinical results of the possibilities of the TMLR in the surgical treatment are presented.

Spin fluctuation effects on the conductance through a single Pd atom contact

International Nuclear Information System (INIS)

Romero, M A; Goldberg, E C; Gomez-Carrillo, S C; Bolcatto, P G

2009-01-01

A controversy about the conductance through single atoms still exists. There are many experiments where values lower than the quantum unity G 0 = 2e 2 /h have been found associated to Kondo regimes with high Kondo temperatures. Specifically in the Pd single atom contact, conductance values close to G 0 /2 at room temperature have been reported. In this work we propose a theoretical analysis of a break junction of Pd where the charge fluctuation in the single atom contact is limited to the most probable one: d 10 ↔d 9 . The projected density of states and the characteristics of the electron transport are calculated by using a realistic description of the interacting system. A Kondo regime is found where the conductance values and their dependence on temperature are in good agreement with the experimental trends observed in the conduction of single molecule transistors based on transition metal coordination complexes.

Description of the control and safety systems of the RA reactor; Opis sistema za upravljanje i sigurnosnu zastitu RA

Energy Technology Data Exchange (ETDEWEB)

Popovic, B; Pesic, M [Institute of Nuclear Sciences Boris Kidric, Reaktor RA, Vinca, Beograd (Yugoslavia)

1962-07-01

This report contains detailed description and scheme of the control and safety system of the RA reactor. It consists of interconnected five systems: for automated regulation; compensation rods; safety rods; power density measurement device; period meter; automated D{sub 2}O level meter in the core. Automated regulation system is divided into two parts: basic system for reactor operation regime at power from 10kW - 10 MW and precise regulation system for operation at set-up power level up to 10 kW which is used occasionally.

Fusion Engineering Device. Volume II. Design description

International Nuclear Information System (INIS)

1981-10-01

This volume summarizes the design of the FED. It includes a description of the major systems and subsystems, the supporting plasma design analysis, a projected device cost and associated construction schedule, and a description of the facilities to house and support the device. This effort represents the culmination of the FY81 studies conducted at the Fusion Engineering Design Center (FEDC). Unique in these design activities has been the collaborative involvement of the Design Center personnel and numerous resource physicists from the fusion community who have made significant contributions in the physics design analysis as well as the physics support of the engineering design of the major FED systems and components

Increase of Organization in Complex Systems

OpenAIRE

Georgiev, Georgi Yordanov; Daly, Michael; Gombos, Erin; Vinod, Amrit; Hoonjan, Gajinder

2013-01-01

Measures of complexity and entropy have not converged to a single quantitative description of levels of organization of complex systems. The need for such a measure is increasingly necessary in all disciplines studying complex systems. To address this problem, starting from the most fundamental principle in Physics, here a new measure for quantity of organization and rate of self-organization in complex systems based on the principle of least (stationary) action is applied to a model system -...

Tokamak Physics EXperiment (TPX): Toroidal field magnet design, development and manufacture. SDRL 15, System design description. Volume 1

International Nuclear Information System (INIS)

1995-01-01

This System Design Description, prepared in accordance with the TPX Project Management Plan provides a summary or TF Magnet System design features at the conclusion of Phase I, Preliminary Design and Manufacturing Research. The document includes the analytical and experimental bases for the design, and plans for implementation in final design, manufacturing, test, and magnet integration into the tokamak. Requirements for operation and maintenance are outlined, and references to sources of additional information are provided

Tokamak Physics EXperiment (TPX): Toroidal field magnet design, development and manufacture. SDRL 15, System design description. Volume 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-22

This System Design Description, prepared in accordance with the TPX Project Management Plan provides a summary or TF Magnet System design features at the conclusion of Phase I, Preliminary Design and Manufacturing Research. The document includes the analytical and experimental bases for the design, and plans for implementation in final design, manufacturing, test, and magnet integration into the tokamak. Requirements for operation and maintenance are outlined, and references to sources of additional information are provided.

48 CFR 12.202 - Market research and description of agency need.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Market research and description of agency need. 12.202 Section 12.202 Federal Acquisition Regulations System FEDERAL ACQUISITION... Commercial Items 12.202 Market research and description of agency need. (a) Market research (see 10.001) is...

A Novel Single Phase Hybrid Switched Reluctance Motor Drive System

DEFF Research Database (Denmark)

Liang, Jianing; Xu, Guoqing; Jian, Linni

2011-01-01

In this paper, a novel single phase hybrid switched reluctance motor(SRM) drive system is proposed. It integrated a single phase hybrid SRM and a novel single phase boost converter. This motor can reduce the number of phase switch. And the permanent magnet which is used in the motor can improve...... the performance and efficiency of SR motor. However, the inherent characteristic of this motor is that the negative torque is very sensitive with the excitation current near the turn-on angle. The slow excitation current limits the torque generation region and reduces the average torque. Therefore, a novel single...... phase boost converter is applied to improve the performance of this motor. It is easy to generate a double dclink voltage and dc-link voltage and switch both of them. The voltage of boost capacitor is self balance, so the protective circuit is not need to consider. The fast excitation mode helps hybrid...

Microscopic description of nuclear reactions

International Nuclear Information System (INIS)

Gorbatov, A.M.

1992-01-01

The genealogical series method has been extended to the continuous spectrum of the many-body systems. New nonlinear integral equations have been formulated to perform the microscopical description of the nuclear reactions with arbitrary number of particles. The way to solve them numerically is demonstrated

Applying Data Mining Techniques to Improve Information Security in the Cloud: A Single Cache System Approach

Directory of Open Access Journals (Sweden)

Amany AlShawi

2016-01-01

Full Text Available Presently, the popularity of cloud computing is gradually increasing day by day. The purpose of this research was to enhance the security of the cloud using techniques such as data mining with specific reference to the single cache system. From the findings of the research, it was observed that the security in the cloud could be enhanced with the single cache system. For future purposes, an Apriori algorithm can be applied to the single cache system. This can be applied by all cloud providers, vendors, data distributors, and others. Further, data objects entered into the single cache system can be extended into 12 components. Database and SPSS modelers can be used to implement the same.

Process tomography via sequential measurements on a single quantum system

CSIR Research Space (South Africa)

Bassa, H

2015-09-01

Full Text Available The authors utilize a discrete (sequential) measurement protocol to investigate quantum process tomography of a single two-level quantum system, with an unknown initial state, undergoing Rabi oscillations. The ignorance of the dynamical parameters...

On the origin of nonclassicality in single systems

International Nuclear Information System (INIS)

Aravinda, S; Srikanth, R; Pathak, Anirban

2017-01-01

In the framework of certain general probability theories of single systems, we identify various nonclassical features such as incompatibility, multiple pure-state decomposability, measurement disturbance, no-cloning and the impossibility of certain universal operations, with the non-simpliciality of the state space. This is shown to naturally suggest an underlying simplex as an ontological model. Contextuality turns out to be an independent nonclassical feature, arising from the intransitivity of compatibility. (paper)

48 CFR 14.404-4 - Restrictions on disclosure of descriptive literature.

Science.gov (United States)

2010-10-01

... of descriptive literature. 14.404-4 Section 14.404-4 Federal Acquisition Regulations System FEDERAL... Contract 14.404-4 Restrictions on disclosure of descriptive literature. When a bid is accompanied by descriptive literature (as defined in 2.101), and the bidder imposes a restriction that prevents the public...

A Direct Algorithm for Pole Placement by State-derivative Feedback for Single-input Linear Systems

Directory of Open Access Journals (Sweden)

Taha H. S. Abdelaziz

2003-01-01

Full Text Available This paper deals with the direct solution of the pole placement problem for single-input linear systems using state-derivative feedback. This pole placement problem is always solvable for any controllable systems if all eigenvalues of the original system are nonzero. Then any arbitrary closed-loop poles can be placed in order to achieve the desired system performance. The solving procedure results in a formula similar to the Ackermann formula. Its derivation is based on the transformation of a linear single-input system into Frobenius canonical form by a special coordinate transformation, then solving the pole placement problem by state derivative feedback. Finally the solution is extended also for single-input time-varying control systems. The simulation results are included to show the effectiveness of the proposed approach.

A Description and Linguistic Analysis of the Tai Khuen Writing System

Directory of Open Access Journals (Sweden)

R. Wyn Owen

2017-03-01

Full Text Available This article provides a description and linguistic analysis of the Tai Tham script-based orthography of Tai Khuen, a Tai-Kadai language spoken in Eastern Shan State, Myanmar. The language has a long history of writing flowing out of the literary and religious culture nurtured by the Lan Na Kingdom from the 13th Century onwards. Comparison of phoneme and grapheme inventories shows that the orthography is well able to represent the spoken language as well as ancient Pali religious texts. Apart from spelling conventions reflecting the etymology of borrowed Pali and Sanskrit morphemes, sound changes over time have also decreased the phonological transparency of the orthography, notwithstanding the need of some more conservative varieties which still preserve distinctions lost in other varieties. Despite the complexities of the script, the literacy rates in Khuen are remarkably high for a minority language not taught in the government school system.

The camera of the fifth H.E.S.S. telescope. Part I: System description

Energy Technology Data Exchange (ETDEWEB)

Bolmont, J., E-mail: bolmont@in2p3.fr [LPNHE, Université Pierre et Marie Curie Paris 6, Université Denis Diderot Paris 7, CNRS/IN2P3, 4 Place Jussieu, F-75252 Paris Cedex 5 (France); Corona, P.; Gauron, P.; Ghislain, P.; Goffin, C.; Guevara Riveros, L.; Huppert, J.-F.; Martineau-Huynh, O.; Nayman, P.; Parraud, J.-M.; Tavernet, J.-P.; Toussenel, F.; Vincent, D.; Vincent, P. [LPNHE, Université Pierre et Marie Curie Paris 6, Université Denis Diderot Paris 7, CNRS/IN2P3, 4 Place Jussieu, F-75252 Paris Cedex 5 (France); Bertoli, W.; Espigat, P.; Punch, M. [APC, AstroParticule et Cosmologie, Université Paris Diderot, CNRS/IN2P3, CEA/Irfu, Observatoire de Paris, Sorbonne Paris Cité, 10, rue Alice Domon et Léonie Duquet, F-75205 Paris Cedex 13 (France); Besin, D.; Delagnes, E.; Glicenstein, J.-F. [CEA Saclay, DSM/IRFU, F-91191 Gif-Sur-Yvette Cedex (France); and others

2014-10-11

In July 2012, as the four ground-based gamma-ray telescopes of the H.E.S.S. (High Energy Stereoscopic System) array reached their tenth year of operation in Khomas Highlands, Namibia, a fifth telescope took its first data as part of the system. This new Cherenkov detector, comprising a 614.5 m{sup 2} reflector with a highly pixelized camera in its focal plane, improves the sensitivity of the current array by a factor two and extends its energy domain down to a few tens of GeV. The present part I of the paper gives a detailed description of the fifth H.E.S.S. telescope's camera, presenting the details of both the hardware and the software, emphasizing the main improvements as compared to previous H.E.S.S. camera technology.

Benchmarking of grid fault modes in single-phase grid-connected photovoltaic systems

DEFF Research Database (Denmark)

Yang, Yongheng; Blaabjerg, Frede; Zou, Zhixiang

2012-01-01

Pushed by the booming installations of single-phase photovoltaic (PV) systems, the grid demands regarding the integration of PV systems are expected to be modified. Hence, the future PV systems should become more active with functionalities of low voltage ride-through (LVRT) and the grid support...