Use of ZnO:Mn particles for degradation of methylene blue by photocatalysis process

International Nuclear Information System (INIS)

Giraldi, T. R.; Swerts, J. P.; Vicente, M. A.; Paris, E.C.; Ribeiro, C.

2016-01-01

The management of water use in the agricultural environment is a key factor to build new environmentally sustainable productive methods. Photocatalysis is a promising method for water decontamination. This research paper aimed to evaluate the photocatalytic potential of pure and Mn-doped ZnO particles. The materials were obtained by the polymeric precursor method, and characterized by X-ray diffraction, N_2 adsorption in low temperature, infrared and ultraviolet spectroscopy, and photoluminescence. In order to evaluate ZnO:Mn particles photo efficiency, experiments were carried out by applying the methylene blue dye solution to photodegradation under UVC exposure. The particles had ZnO single-phase, but low specific surface area. The sample ZnO:0.25% Mn presented higher efficiency in the methylene blue photocatalytic degradation test. This efficiency was related to a higher band gap energy value and a lower rate of electron recombination, which allows greater formation of hydroxyl radicals, which are responsible for dye degradation. (author)

Preoperative Localization of Mediastinal Parathyroid Adenoma with Intra-arterial Methylene Blue

Energy Technology Data Exchange (ETDEWEB)

Salman, Rida; Sebaaly, Mikhael G. [American University of Beirut Medical Center, Department of Diagnostic Radiology (Lebanon); Wehbe, Mohammad Rachad; Sfeir, Pierre; Khalife, Mohamad [American University of Beirut Medical Center, Department of General Surgery (Lebanon); Al-Kutoubi, Aghiad, E-mail: mk00@aub.edu.lb [American University of Beirut Medical Center, Department of Diagnostic Radiology (Lebanon)

2017-06-15

Ectopic parathyroid is found in 16% of patients with hyperparathyroidism. 2% of ectopic parathyroid adenomas are not accessible to standard cervical excision. In such cases, video-assisted thoracoscopic resection is the recommended definitive treatment. We present a case of mediastinal parathyroid adenoma localized preoperatively by injecting methylene blue within a branch of the internal mammary artery that is supplying the adenoma. Intra-arterial methylene blue injection facilitated visualization and resection of the adenoma. The preoperative intra-arterial infusion of methylene blue appears to be an effective and safe method for localization of ectopic mediastinal parathyroid adenomas and allows rapid identification during thoracoscopic resection.

Study of extraction-spectrophotometric micro-determination of boron with methylene blue and its application

International Nuclear Information System (INIS)

Zhu Daohong

1990-08-01

A sensitive extraction-spectrophotometric method for microdetermination of boron with methylene blue was investigated. The method was based on the extraction of a BF 4 - -methylene blue complex into dichloroethane. Boron was determined directly by measuring the absorbance at 658 nm. The calibration graph was linear over the range of 2.5 x 10 -9 to 8 x 10 -8 g/mL. The blank, mechanism of the reactions, interference of other ions and some optimum conditions of the method were studied in detail. The main source of the blank resulted from methylene blue and the complex of F - -methylene blue. In order to reduce the blank, the amounts of methylene blue, H 2 SO 4 and HF were used as less as possible. Only one to one complex BF 4 - -methylene blue was formed in the medium of H 2 SO 4 . About 90% of methylene blue and F - -methylene blue complex was removre with 5 ml of water and only a little amount of BF 4 -methylene blue complex was decomposed. The extraction-spectrophotometric method with methylene blue was first applied to the microdetermination of boron in sodium metal and UF 6 . The sample of sodium metal was taken and weighed in the glovebox filled with argon. Then sodium metal was oxidized, hydrolyzed, netralized and fluorizated with H 2 O, H 2 SO 4 and HF, respectively. The 0.5 ppm of boron in sodium metal was determined with a relative error about ±4%. This method can be applied to the determination of boron in sodium metal, sodium sulfate and sodium hydroxide at diffeent grades. The species of boron in the hydrolysate of UF 6 is BF 4 - anion, so the sample can be directly analyzed. Boron contents in the range of 0.1 to 0.5 ppm was determined with a relative error about ±3%. Six samples could be analysed in 2h

Intraoperative use of fibrin glue dyed with methylene blue in surgery for branchial cleft anomalies.

Science.gov (United States)

Piccioni, Michela; Bottazzoli, Marco; Nassif, Nader; Stefini, Stefania; Nicolai, Piero

2016-09-01

We present a new method of optimizing the results of surgery for branchial cleft anomalies based on the intraoperative injection of fibrin glue combined with methylene blue dye. Retrospective single-center cohort study. The method was applied in 17 patients suffering from branchial anomalies. Six (35.29%) had a preauricular lesion; three (17.65%) had lesions derived from the first arch/pouch/groove (type I), four (23.53%) had lesions derived from the first (type II), one (5.88%) had lesions derived from the second, one (5.88%) had lesions derived from the third, and two (11.76%) had lesions derived from the fourth. The median and mean age at surgery were 10 and 10.6 years, respectively. All patients were followed by periodic clinical and ultrasonographic examination. The combination of fibrin glue with methylene blue facilitated the correct assessment of the extension of the lesions and their intraoperative manipulation. After a mean follow-up of 47.8 months, all patients were free of disease. Intraoperative injection of branchial fistulae and cysts by a mixture of fibrin glue and methylene blue is an effective, easy, and safe tool to track lesions and achieve radical resection. The technique requires a definitive validation on a large cohort with adequate stratification of patients. 4 Laryngoscope, 126:2147-2150, 2016. © 2015 The American Laryngological, Rhinological and Otological Society, Inc.

Methylene Blue to Treat Protamine-induced Anaphylaxis Reactions. An Experimental Study in Pigs

Directory of Open Access Journals (Sweden)

Agnes Afrodite S. Albuquerque

Full Text Available ABSTRACT Objective: To examine if methylene blue (MB can counteract or prevent protamine (P cardiovascular effects. Methods: The protocol included five heparinized pig groups: Group Sham -without any drug; Group MB - MB 3 mg/kg infusion; Group P - protamine; Group P/MB - MB after protamine; Group MB/P - MB before protamine. Nitric oxide levels were obtained by the nitric oxide/ozone chemiluminescence method, performed using the Nitric Oxide Analizer 280i (Sievers, Boulder, CO, USA. Malondialdehyde plasma levels were estimated using the thiobarbiturate technique. Results: 1 Groups Sham and MB presented unchanged parameters; 2 Group P - a Intravenous protamine infusion caused mean arterial pressure decrease and recovery trend after 25-30 minutes, b Cardiac output decreased and remained stable until the end of protamine injection, and c Sustained systemic vascular resistance increased until the end of protamine injection; 3 Methylene blue infusion after protamine (Group P/MB - a Marked mean arterial pressure decreased after protamine, but recovery after methylene blue injection, b Cardiac output decreased after protamine infusion, recovering after methylene blue infusion, and c Sustained systemic vascular resistance increased after protamine infusion and methylene blue injections; 4 Methylene blue infusion before protamine (Group MB/P - a Mean arterial pressure decrease was less severe with rapid recovery, b After methylene blue, there was a progressive cardiac output increase up to protamine injection, when cardiac output decreased, and c Sustained systemic vascular resistance decreased after protamine, followed by immediate Sustained systemic vascular resistance increase; 5 Plasma nitrite/nitrate and malondialdehyde values did not differ among the experimental groups. Conclusion: Reviewing these experimental results and our clinical experience, we suggest methylene blue safely prevents and treats hemodynamic protamine complications, from the

Surfactant-assisted hydrothermal fabrication and visible-light-driven photocatalytic degradation of methylene blue over multiple morphological BiVO4 single-crystallites

International Nuclear Information System (INIS)

Meng Xue; Zhang Lei; Dai Hongxing; Zhao Zhenxuan; Zhang Ruzhen; Liu Yuxi

2011-01-01

Monoclinic BiVO 4 single-crystallites with polyhedral, rod-like, tubular, leaf-like, and spherical morphologies have been fabricated using the triblock copolymer P123-assisted hydrothermal strategy with bismuth nitrate and ammonium metavanadate as metal source and various bases as pH adjustor. The physicochemical properties of the materials were characterized by means of the XRD, TGA/DSC, Raman, HRSEM, HRTEM/SAED, XPS, and UV-vis techniques. The photocatalytic activities of the as-fabricated BiVO 4 samples were measured for the photodegradation of methylene blue (MB) under visible-light irradiation. It is shown that factors, such as the pH value of precursor solution, the introduction of surfactant, the nature of alkaline source, and the hydrothermal temperature, have a crucial influence on the particle architecture of the BiVO 4 product. Among the as-fabricated BiVO 4 samples, the ones derived hydrothermally with P123 at pH = 6 or 10 possessed excellent optical absorption performance both in UV- and visible-light regions and hence showed outstanding photocatalytic activities for the addressed reaction. The unusually high visible-light-driven catalytic performance of monoclinically crystallized rod-like and tubular BiVO 4 single-crystallites is associated with the higher surface areas and concentrations of surface oxygen defects, and unique particle morphologies. The possible formation mechanisms of such multiple morphological BiVO 4 materials have also been discussed.

Process for crosslinking methylene-containing aromatic polymers with ionizing radiation

Science.gov (United States)

Bell, Vernon L. (Inventor); Havens, Stephen J. (Inventor)

1990-01-01

A process for crosslinking aromatic polymers containing radiation-sensitive methylene groups (-CH2-) by exposing the polymers to ionizing radiation thereby causing crosslinking of the polymers through the methylene groups is described. Crosslinked polymers are resistant to most organic solvents such as acetone, alcohols, hydrocarbons, methylene, chloride, chloroform, and other halogenated hydrocarbons, to common fuels and to hydraulic fluids in contrast to readily soluble uncrosslinked polymers. In addition, the degree of crosslinking of the polymers depends upon the percentage of the connecting groups which are methylene which ranges from 5 to 50 pct and preferably from 25 to 50 pct of the connecting groups, and is also controlled by the level of irradiation which ranges from 25 to 1000 Mrads and preferably from 25 to 250 Mrads. The temperature of the reaction conditions ranges from 25 to 200 C and preferably at or slightly above the glass transition temperature of the polymer. The crosslinked polymers are generally more resistant to degradation at elevated temperatures such as greater than 150 C, have a reduced tendency to creep under load, and show no significant embrittlement of parts fabricated from the polymers.

Complications of Methylene Blue Dye in Breast Surgery: Case Reports and Review of the Literature

Directory of Open Access Journals (Sweden)

FJ Reyes, MB Noelck, C Valentino, L Grasso-LeBeau, JE Lang

2011-01-01

Full Text Available Introduction: Methylene blue dye has been used worldwide successfully with few complications in breast surgery. We present two different complications involving methylene blue: 1 skin and parenchymal necrosis when dye was injected in a subdermal fashion and 2 Mycoplasma infection caused by contaminated methylene blue in breast reduction surgery.Methods: We present two cases seen at the University of Arizona during 2008 and referred to a breast surgeon for management. We evaluated and managed complications of methylene blue dye injected by 2 referring surgeons for different indications. A review of the literature was performed.Results: The first case is a 67 year old female diagnosed with infiltrating ductal carcinoma of the left breast for which she was treated by her initial surgeon with left segmental mastectomy and sentinel node biopsy. The operating surgeon injected methylene blue in a subareolar subdermal fashion (distant from the primary tumor; unfortunately the patient suffered skin and breast necrosis requiring multiple surgical debridements and finally achieving delayed primary closure. The second case is a 45 year old female with infiltrating lobular carcinoma with a history of Mycoplasma infection secondary to methylene blue injected for breast reduction surgery. She required multiple debridements and had granulomas masquerading as cancer on MRI that confounded her extent of disease.Conclusions: The use of methylene blue dye in breast surgery is not without risk. In both cases methylene blue was responsible for complications requiring surgical debridement for local wound problems. In each case severe necrosis and infection were present. Methylene blue may cause not only significant morbidity, but may also produce cosmetically unsatisfactory results.

Methylene Blue for Vasoplegia When on Cardiopulmonary Bypass During Double-Lung Transplantation.

Science.gov (United States)

Carley, Michelle; Schaff, Jacob; Lai, Terrance; Poppers, Jeremy

2015-10-15

Vasoplegia syndrome, characterized by hypotension refractory to fluid resuscitation or high-dose vasopressors, low systemic vascular resistance, and normal-to-increased cardiac index, is associated with increased morbidity and mortality after cardiothoracic surgery. Methylene blue inhibits inducible nitric oxide synthase and guanylyl cyclase, and has been used to treat vasoplegia during cardiopulmonary bypass. However, because methylene blue is associated with increased pulmonary vascular resistance, its use in patients undergoing lung transplantion has been limited. Herein, we report the use of methylene blue to treat refractory vasoplegia during cardiopulmonary bypass in a patient undergoing double-lung transplantation.

Breakwater stability with damaged single layer armour units

NARCIS (Netherlands)

De Rover, R.; Verhagen, H.J.; Van den Berge, A.; Reedijk, B.

2008-01-01

The effect of single layer interlocking armour unit breakage on the hydraulic armour layer stability and potential damage progression is addressed in this paper. A 2-dimensional scale model of a rubble mound breakwater with an armour layer consisting of Xbloc armour units was tested. The residual

Enhanced Photocatalytic Performance of NiO-Decorated ZnO Nanowhiskers for Methylene Blue Degradation

Directory of Open Access Journals (Sweden)

I. Abdul Rahman

2014-01-01

Full Text Available ZnO nanowhiskers were used for photodecomposition of methylene blue in aqueous solution under UV irradiation. The rate of methylene blue degradation increased linearly with time of UV irradiation. 54% of degradation rate was observed when the ZnO nanowhiskers were used as photocatalysts for methylene blue degradation for 80 min under UV irradiation. The decoration of p-type NiO nanoparticles on n-type ZnO nanowhiskers significantly enhanced photocatalytic activity and reached 72% degradation rate of methylene blue by using the same method. NiO-decorated ZnO was recycled for second test and shows 66% degradation from maximal peak of methylene blue within the same period. The increment of photocatalytic activity of NiO-decorated ZnO nanowhiskers was explained by the extension of the electron depletion layer due to the formation of nanoscale p-n junctions between p-type NiO and n-type ZnO. Hence, these products provide new alternative proficient photocatalysts for wastewater treatment.

Film dosimeters based on methylene blue and methyl orange in polyvinyl alcohol

DEFF Research Database (Denmark)

Chung, W.H.; Miller, A.

1994-01-01

Polyvinyl alcohol (PVA) films containing methylene blue and methyl orange are useful as gamma and electron radiation dosimeters. Absorbed doses should not exceed 40 kGy for methylene blue and 500 kGy for methyl orange. Because PVA is water-soluble, the films may be made without toxic solvents...

Retrograde Instillation of Methylene Blue in the Difficult Diagnosis of BPF

Directory of Open Access Journals (Sweden)

F. Ravenna

2012-01-01

Full Text Available We report two cases in which we were able to diagnose bronchopleural fistula through retrograde methylene blue instillation during bronchoscopy. In the first case, methylene blue was injected through an abdominal drain, followed by air instillation and detected in the left bronchial tree, demonstrating the presence of a fistula in the lingula’s bronchus. In the second case, methylene blue was injected into a pleural drain, through a breach on a surgical suture and detected in the right bronchial tree, demonstrating the presence of a fistula in the right inferior bronchus. The retrograde instillation of methylene blue, through a drain in the abdomen or the thoracic wall, is a safe, cheap, and practical method that allows the bronchoscopist to identify the presence of a fistula and, more importantly, to identify the exact point on the bronchial tree where a fistula is located. This provides the possibility of sealing the fistula with a variety of devices. It is our opinion that this procedure should be considered a primary method of diagnosis when a bronchopleural fistula is suspected and a drain on the thoracic or abdominal wall is positioned such that effusions are able to drain.

Methylene blue doped polymers: efficient media for optical recording

Science.gov (United States)

Ushamani, M.; Sreekumar, K.; Sudha Kartha, C.; Joseph, R.

2004-05-01

Polymer materials find application in optical storage technology, namely in the development of high information density and fast access type memories. A new polymer blend of methylene blue sensitized polyvinyl alcohol (PVA) and polyacrylic acid (PAA) in methanol is prepared and characterized and its comparison with methylene blue sensitized PVA in methanol and complexed methylene blue sensitized polyvinyl chloride (CMBPVC) is presented. The optical absorption spectra of the thin films of these polymers showed a strong and broad absorption region at 670-650 nm, matching the wavelength of the laser used. A very slow recovery of the dye on irradiation was observed when a 7:3 blend of polyvinyl alcohol/polyacrylic acid at a pH of 3.8 and a sensitizer concentration of 4.67 · 10-5 g/ml were used. A diffraction efficiency of up to 20% was observed for the MBPVA/alcohol system and an energetic sensitivity of 2000 mJ/cm2 was obtained in the photosensitive films with a spatial frequency of 588 lines/mm.

INTERACTION MODE BETWEEN METHYLENE BLUE-Sm(III ...

African Journals Online (AJOL)

Preferred Customer

between methylene blue (MB)-Sm(III) complex and herring sperm DNA by using acridine orange .... the complex was recorded as KBr pellets on Spectrum One FTIR system (PE Company, USA), ..... mechanism of drugs and drug design.

Uniform Cu2Cl(OH)3 hierarchical microspheres: A novel adsorbent for methylene blue adsorptive removal from aqueous solution

International Nuclear Information System (INIS)

Wei, Wei; Gao, Pin; Xie, Jimin; Zong, Sekai; Cui, Henglv; Yue, Xuejie

2013-01-01

Using the solution phase method without any surfactants or templates, the hierarchical of Cu 2 Cl(OH) 3 microspheres were synthesized by freeze drying. The size and surface area of the microspheres are ca. 1–2 µm and 76.61 m 2 g −1 , respectively. A possible formation mechanism is presented based on the experimental results. Methylene blue was chosen to investigate the adsorption capacity of the as-prepared adsorbent. The effects of various experimental parameters, such as pH, initial dye concentration, and contact time were investigated. The results showed that the dye removal increased with the increasing in the initial concentration of the dye and also increased in the amount of microspheres used and initial pH. Adsorption data fitted well with the Freundlich adsorption isotherm. The thermodynamic analysis presented the exothermic, spontaneous and more ordered arrangement process. The microspheres could be employed effective for removal of dyes from aqueous solution. - Graphical abstract: The single-crystalline hierarchical Cu 2 Cl(OH) 3 spheres can be prepared for the first time by using a template-free process through freeze-drying. Meanwhile, the hierarchical spheres exhibited high adsorption capacity to methylene blue. Display Omitted - Highlights: • Cu 2 Cl(OH) 3 microspheres were successfully synthesized through a freeze drying process. • A possible formation mechanism of hierarchical microspheres was presented. • The Cu 2 Cl(OH) 3 microspheres have high methylene blue adsorption capacity. • Methylene blue adsorption is a spontaneous and exothermic process. • The adsorption mechanism of microspheres onto dye was proposed in detail

Continuous adsorption of methylene blue dye on the maize stem ground tissue

Directory of Open Access Journals (Sweden)

Kojić Predrag S.

2017-01-01

Full Text Available Continuous adsorption of methylene blue from aqueous solutions onto maize stem ground tissue in column mode was investigated. The study encompassed the effects of important parameters such as flow rate, initial concentration of methylene blue, and bed depth on methylene blue removal from model solutions. The maximum adsorption capacity of the maize stem was 45.9 mg/g at the initial methylene blue concentration of 20 mg/L, bed height of 6.5 cm and flow rate of 8 mL/min. It was found that the breakthrough time for reaching saturation increased with a decrease in the flow rate, and also occurred earlier for a higher influent concentration. The breakthrough times increased with the bed depth, thus allowing a larger volume to be treated. The Adams-Bohart, Yoon-Nelson, Clark and artificial neural network models were used to predict the breakthrough curves. These models gave excellent approximations of the experimental behavior.[Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 172025

[Aftercare for durability and profitability of single-unit and multi-unit fixed dental prostheses

NARCIS (Netherlands)

Baat, C. de; Loveren, C. van; Maarel-Wierink, C.D. van der; Witter, D.J.; Creugers, N.H.J.

2013-01-01

An important aim ofa treatment with single-unit and multi-unit fixed dental prostheses is a durable and profitable treatment outcome. That requires aftercare, too. First, the frequency of routine oral examinations should be assessed, using an individual risk profile. The objectives of the routine

Prefrontal single-unit firing associated with deficient extinction in mice

Science.gov (United States)

Fitzgerald, Paul J; Whittle, Nigel; Flynn, Shaun M; Graybeal, Carolyn; Pinard, Courtney; Gunduz-Cinar, Ozge; Kravitz, Alexxai; Singewald, Nicolas; Holmes, Andrew

2014-01-01

The neural circuitry mediating fear extinction has been increasingly well studied and delineated. The rodent infralimbic subregion (IL) of the ventromedial prefrontal cortex (vmPFC) has been found to promote extinction, whereas the prelimbic cortex (PL) demonstrates an opposing, pro-fear, function. Studies employing in vivo electrophysiological recordings have observed that while increased IL single-unit firing and bursting predicts robust extinction retrieval, increased PL firing can correlate with sustained fear and poor extinction. These relationships between single-unit firing and extinction do not hold under all experimental conditions, however. In the current study, we further investigated the relationship between vmPFC and PL single-unit firing and extinction using inbred mouse models of intact (C57BL/6J, B6) and deficient (129S1/SvImJ, S1) extinction strains. Simultaneous single-unit recordings were made in the PL and vmPFC (encompassing IL) as B6 and S1 mice performed extinction training and retrieval. Impaired extinction retrieval in S1 mice was associated with elevated PL single-unit firing, as compared to firing in extinguishing B6 mice, consistent with the hypothesized pro-fear contribution of PL. Analysis of local field potentials also revealed significantly higher gamma power in the PL of Sthan B6 mice during extinction training and retrieval. In the vmPFC, impaired extinction in S1 mice was also associated with exaggerated single-unit firing, relative to B6 mice. This is in apparent contradiction to evidence that IL activity promotes extinction, but could reflect a (failed) compensatory effort by the vmPFC to mitigate fear-promoting activity in other regions, such as the PL or amygdala. In support of this hypothesis, augmenting IL activity via direct infusion of the GABAA receptor antagonist picrotoxin rescued impaired extinction retrieval in S1 mice. Chronic fluoxetine treatment produced modest reductions in fear during extinction retrieval and

Assessing Urinary Tract Junction Obstruction Defects by Methylene Blue Dye Injection.

Science.gov (United States)

Yun, Kangsun

2017-10-12

Urinary tract junction obstruction defects are congenital anomalies inducing hydronephrosis and hydroureter. Murine urinary tract junction obstruction defects can be assessed by tracking methylene blue dye flow within the urinary system. Methylene blue dye is injected into the renal pelvis of perinatal embryonic kidneys and dye flow is monitored from the renal pelvis of the kidney through the ureter and into the bladder lumen after applying hydrostatic pressure. Dye accumulation will be evident in the bladder lumen of the normal perinatal urinary tract, but will be constrained between the renal pelvis and the end point of an abnormal ureter, if urinary tract obstructions occur. This method facilitates the confirmation of urinary tract junction obstructions and visualization of hydronephrosis and hydroureter. This manuscript describes a protocol for methylene blue dye injection into the renal pelvis to confirm urinary tract junction obstructions.

DNA Electrochemistry with Tethered Methylene Blue

Science.gov (United States)

Pheeney, Catrina G.

2012-01-01

Methylene blue (MB′), covalently attached to DNA through a flexible C12 alkyl linker, provides a sensitive redox reporter in DNA electrochemistry measurements. Tethered, intercalated MB′ is reduced through DNA-mediated charge transport; the incorporation of a single base mismatch at position 3, 10, or 14 of a 17-mer causes an attenuation of the signal to 62 ± 3% of the well-matched DNA, irrespective of position in the duplex. The redox signal intensity for MB′–DNA is found to be least 3-fold larger than that of Nile blue (NB)–DNA, indicating that MB′ is even more strongly coupled to the π-stack. The signal attenuation due to an intervening mismatch does, however, depend on DNA film density and the backfilling agent used to passivate the surface. These results highlight two mechanisms for reduction of MB′ on the DNA-modified electrode: reduction mediated by the DNA base pair stack and direct surface reduction of MB′ at the electrode. These two mechanisms are distinguished by their rates of electron transfer that differ by 20-fold. The extent of direct reduction at the surface can be controlled by assembly and buffer conditions. PMID:22512327

Efficient Synthesis of Single-Chain Polymer Nanoparticles via Amide Formation

Directory of Open Access Journals (Sweden)

Ana Sanchez-Sanchez

2015-01-01

Full Text Available Single-chain technology (SCT allows the transformation of individual polymer chains to folded/collapsed unimolecular soft nanoparticles. In this work we contribute to the enlargement of the SCT toolbox by demonstrating the efficient synthesis of single-chain polymer nanoparticles (SCNPs via intrachain amide formation. In particular, we exploit cross-linking between active methylene groups and isocyanate moieties as powerful “click” chemistry driving force for SCNP construction. By employing poly(methyl methacrylate- (PMMA- based copolymers bearing β-ketoester units distributed randomly along the copolymer chains and bifunctional isocyanate cross-linkers, SCNPs were successfully synthesized at r.t. under appropriate reaction conditions. Characterization of the resulting SCNPs was carried out by means of a combination of techniques including size exclusion chromatography (SEC, infrared (IR spectroscopy, proton nuclear magnetic resonance (1H NMR spectroscopy, dynamic light scattering (DLS, and elemental analysis (EA.

A Stereoselective [3+1] Ring Expansion for the Synthesis of Highly Substituted Methylene Azetidines.

Science.gov (United States)

Schmid, Steven C; Guzei, Ilia A; Schomaker, Jennifer M

2017-09-25

The reaction of rhodium-bound carbenes with strained bicyclic methylene aziridines results in a formal [3+1] ring expansion to yield highly substituted methylene azetidines with excellent regio- and stereoselectivity. The reaction appears to proceed through an ylide-type mechanism, where the unique strain and structure of the methylene aziridine promotes a ring-opening/ring-closing cascade that efficiently transfers chirality from substrate to product. The resultant products can be elaborated into new azetidine scaffolds containing vicinal tertiary-quaternary and even quaternary-quaternary stereocenters. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Degradation of methylene blue by radio frequency plasmas in water under ultraviolet irradiation

Energy Technology Data Exchange (ETDEWEB)

Maehara, Tsunehiro, E-mail: maehara@phys.sci.ehime-u.ac.jp [Graduate School of Science and Engineering, Ehime University, Matsuyama 790-8577 (Japan); Nishiyama, Kyohei; Onishi, Shingo; Mukasa, Shinobu; Toyota, Hiromichi [Graduate School of Science and Engineering, Ehime University, Matsuyama 790-8577 (Japan); Kuramoto, Makoto [Integrated Center for Science, Ehime University, Matsuyama 790-8577 (Japan); Nomura, Shinfuku [Graduate School of Science and Engineering, Ehime University, Matsuyama 790-8577 (Japan); Kawashima, Ayato [Faculty of Agriculture, Ehime University, Matsuyama 790-8566 (Japan)

2010-02-15

The degradation of methylene blue by radio frequency (RF) plasmas in water under ultraviolet (UV) irradiation was studied experimentally. When the methylene blue solution was exposed to RF plasma, UV irradiation from a mercury vapor lamp enhanced degradation significantly. A lamp without power supply also enhanced degradation since weak UV light was emitted weakly from the lamp due to the excitation of mercury vapor by stray RF power. Such an enhancement is explained by the fact that after hydrogen peroxide is produced via the recombination process of OH radicals around the plasma, OH radicals reproduced from hydrogen peroxide via the photolysis process degrade methylene blue.

Quantitative evaluation of plasma after methylene blue and white light treatment in four Chinese blood centers.

Science.gov (United States)

Chunhui, Yang; Guohui, Bian; Hong, Yang; Xiaopu, Xiao; Zherong, Bai; Mingyuan, Wang; Xinsheng, Zhang; Juanjuan, Wang; Changqing, Li; Wuping, Li

2013-12-01

Pathogen reduction technology is an important process in the blood safety system, including solvent/detergent treatment, filtration and methylene blue-photochemical technology (MB-PCT). To investigate the quality of MB-PCT-treated plasma, plasma samples from four Chinese blood centers were analyzed over 12 months of storage to determine the recovery of activities and levels of various plasma proteins. Ten plasma units each from the Suzhou, Yancheng, Chongqing and Shandong blood centers were divided into two aliquots. One was subjected to treatment with one of two methylene blue-photochemical technology instruments and the other was used as control. The treated and untreated sample pairs were stored at -30°C. The recovery rates of coagulation factors, inhibitor proteins, total protein, immunoglobulins, and complement proteins were measured at different time points after storage. The mean recovery of most proteins exceeded 80% after MB treatment. The exceptions were factor XI and fibrinogen, of which only 71.3-74% and 69.0-92.3% were retained during storage. The two equipment types differed in terms of residual MB concentration in the plasma samples (0.18 μM and 0.29 μM, respectively). They had similar protein recovery rates at 0.5 month but differed at later time points. The four blood centers differed significantly with regard to factor II, V, VIII and fibrinogen activities. Only the samples from the Shandong blood center met the methylene blue treated fresh frozen plasma requirement. The major factor that influenced the quality of the MB-FFP samples was the time taken between blood collection and storage. Methylene blue treated plasma showed reduced coagulation factor (CF) activity and protein levels. The MB treatment-induced damage to the proteins was acceptable at the four Chinese blood centers, but the quality of the MB-treated plasma in general was not satisfactory. The main factor affecting plasma quality may be the duration of the collection and

Electrochemical preparation of poly(methylene blue)/graphene nanocomposite thin films

International Nuclear Information System (INIS)

Erçarıkcı, Elif; Dağcı, Kader; Topçu, Ezgi; Alanyalıoğlu, Murat

2014-01-01

Highlights: • Poly(MB)/graphene thin films are prepared by a simple electrochemical approach. • Graphene layers in the film show a broad band in visible region of absorbance spectra. • Morphology of composite films indicates both disordered and ordered regions. • XRD reveals that nanocomposite films include rGO layers after electropolymerization process. • Chemically prepared graphene is better than electrochemically prepared graphene for electrooxidation of nitrite. - Abstract: Poly(methylene blue)/graphene nanocomposite thin films were prepared by electropolymerization of methylene blue in the presence of graphene which have been synthesized by two different methods of a chemical oxidation process and an electrochemical approach. Synthesized nanocomposite thin films were characterized by using cyclic voltammetry, UV–vis. absorption spectroscopy, powder X-ray diffraction, and scanning tunneling microscopy techniques. Electrocatalytical properties of prepared poly(methylene blue)/graphene nanocomposite films were compared toward electrochemical oxidation of nitrite. Under optimized conditions, electrocatalytical effect of nanocomposite films of chemically prepared graphene through electrochemical oxidation of nitrite was better than that of electrochemically prepared graphene

Removal of congo red and methylene blue from waste water using coagulation

International Nuclear Information System (INIS)

Ghaffar, S.; Nosheen, S.; Ahmad, N.

2011-01-01

The textile industry has been condemned as being one of the world's worst offenders in terms of pollution Because of increasing population and industrial developments, a huge amount of wastewater is discharged to the environment above the level that the nature can eliminate. Many techniques like oxidation, reduction, physical treatment and biological method are available for removal of colored dyes from wastewater. The work presented here involved the decolorisation of wastewater containing congo red and methylene blue using various coagulants such as alum, bentonite and lime. The effect of various experimental factors such as dosage of coagulants, contact time between coagulant and dye and concentration of dyes and working environment like shaking and static was studied. Under static condition alum give almost 43% removal of congo red while with 10 minutes shaking 74 % removal of 80 dye was achieved with same coagulant. The highest removal of congo red was found to be 99.5 % by using alum after 30 minutes of shaking but in case of methylene blue it intensified the color and gave negative results. Lime gave only 33 % color removal of congo red under static conditions while 57% color was removed under shaking conditions. Maximum color removal achieved by lime was 89% at 40 minutes with shaking condition. Lime gave 60% removal of methylene blue in static condition and 90% removal in shaking condition and maximum absorbance at 80 ppm was 90%. Bentonite also used for the removal of methylene blue and gave 89% removal in shaking condition. By increasing shaking time %age removal increased to 100% at 40 min. And amount of coagulant increased the removal efficiency it attained 100% in both lime and bentonite coagulant for methylene blue Overall alum was found to be better coagulant for the removal of congo red from its aqueous solution. Lime and bentonite both proved better and economical for removal of methylene blue from aqueous solution at lab scale. (author)

21 CFR 558.76 - Bacitracin methylene disalicylate.

Science.gov (United States)

2010-04-01

...) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS NEW ANIMAL DRUGS FOR USE IN ANIMAL FEEDS Specific New Animal Drugs for Use in Animal Feeds § 558.76 Bacitracin methylene disalicylate. (a) Approvals. Type A.... (b) Special considerations. The quantities of antibiotics are expressed in terms of the equivalent...

21 CFR 700.19 - Use of methylene chloride as an ingredient of cosmetic products.

Science.gov (United States)

2010-04-01

... cosmetic products. 700.19 Section 700.19 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) COSMETICS GENERAL Requirements for Specific Cosmetic Products § 700.19 Use of methylene chloride as an ingredient of cosmetic products. (a) Methylene chloride has been used...

Microfluidics-based microbubbles in methylene blue solution for photoacoustic and ultrasound imaging

Science.gov (United States)

Das, Dhiman; Sivasubramanian, Kathyayini; Yang, Chun; Pramanik, Manojit

2018-02-01

Contrast agents which can be used for more than one bio-imaging technique has gained a lot of attention from researchers in recent years. In this work, a microfluidic device employing a flow-focusing junction, is used for the continuous generation of monodisperse nitrogen microbubbles in methylene blue, an optically absorbing organic dye, for dual-modal photoacoustic and ultrasound imaging. Using an external phase of polyoxyethylene glycol 40 stearate (PEG 40), a non-ionic surfactant, and 50% glycerol solution at a flow rate of 1 ml/hr and gas pressure at 1.75 bar, monodisperse nitrogen microbubbles of diameter 7 microns were obtained. The external phase also contained methylene blue hydrate at a concentration of 1 gm/litre. The monodisperse microbubbles produced a strong ultrasound signal as expected. It was observed that the signal-to-noise (SNR) ratio of the photoacoustic signal for the methylene blue solution in the presence of the monodisperse microbubbles was 68.6% lower than that of methylene blue solution in the absence of microbubbles. This work is of significance because using microfluidics, we can precisely control the bubbles' production rate and bubble size which increases ultrasound imaging efficiency. A uniform size distribution of the bubbles will have narrower resonance frequency bandwidth which will respond well to specific ultrasound frequencies.

Allene functionalization via bicyclic methylene aziridines.

Science.gov (United States)

Boralsky, Luke A; Marston, Dagmara; Grigg, R David; Hershberger, John C; Schomaker, Jennifer M

2011-04-15

The oxidative functionalization of olefins is a common method for the formation of vicinal carbon-heteroatom bonds. However, oxidative methods to transform allenes into synthetic motifs containing three contiguous carbon-heteroatom bonds are much less developed. This paper describes the use of bicyclic methylene aziridines (MAs), prepared via intramolecular allene aziridination, as scaffolds for functionalization of all three allene carbons. © 2011 American Chemical Society

[Aftercare for durability and profitability of single-unit and multi-unit fixed dental prostheses].

Science.gov (United States)

de Baat, C; van Loveren, C; van der Maarel-Wierink, C D; Witter, D J; Creugers, N H J

2013-01-01

An important aim ofa treatment with single-unit and multi-unit fixed dental prostheses is a durable and profitable treatment outcome. That requires aftercare, too. First, the frequency of routine oral examinations should be assessed, using an individual risk profile. The objectives of the routine oral examinations are the prevention and, when necessary, the treatment of pathological conditions and complications. With regard to prevention, attention should be paid to information and instruction, oral biofilm and calculus, non-functional activities, hard tooth tissues, periodontal and peri-implant tissues, and saliva. Subsequently, it can be determined whether the intended durability and profitability have been achieved or can still be achieved, whether or not through indicated adjustments. Special attention should be paid to endodontically treated teeth. Restorative, repair or replacement treatments may be indicated in case ofcomplications, such as loose single- or multi-unitfixed dental prosthesis, fracture of a fixed dental prosthesis unit, lost tooth pulp vitality, tooth root fracture, and implant or implant abutment problems.

Novel methylene-blue-sensitized photopolymers for holographic recording: a comparison

Science.gov (United States)

Ushamani, Mythili; Sreekumar, K.; Sudha Kartha, C.; Joseph, Rani

2004-06-01

Polymer matrices like PVC and a blend of PVA/PAA is introduced as new holographic media that cause red sensitivity with methylene blue. Unlike methylene blue sensitized polymers like PVA, PMMA, gelatin etc, the change of state occurring for methylene blue on laser irradiation on PVC matrix was found to be permanent. No recovery of dye on the irradiated spot was observed on storage. The outstanding properties of this material are its excellent optical clarity, insensitive to humidity, economical, ease of fabrication, absence of dark room storage etc. The recovery of dye in conventional MBPVA matrix can be delayed by blending PVA with PAA. Optimization of the ratio of PVA/PAA, the sensitizer concentration, pH, energy, diffraction efficiency measurements etc are done. pH is found to have a great influence on the recovery of the dye in this matrix. The effect of monomers in improving the diffraction efficiency on these dye doped polymer system is also evaluated. A comparative study is done on these polymer matrices and holographic gratings were recorded on these films from a He- Ne laser operating at 632.8 nm.

Methylene blue adsorption from aqueous solution by dehydrated peanut hull

Energy Technology Data Exchange (ETDEWEB)

Ozer, Dursun [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey); Dursun, Guelbeyi [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey)]. E-mail: gdursun@firat.edu.tr; Ozer, Ahmet [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey)

2007-06-01

Dyes are colour organic compounds which can colorize the other substances. These substances usually presents in the effluent water of many industries, such as textiles, leather, paper, printing and cosmetics. To observe the potential feasibility of removing colour, peanut hull as an agricultural by-product was dehydrated with sulphuric acid (DPH) and used for adsorption of methylene blue (MB) from aqueous solution. The effects of various parameters such as initial methylene blue concentrations, temperatures and particle sizes were examined and optimal experimental conditions were determined. Adsorption data were well described by the Langmuir model, although they could be modelled by the Freundlich model as well. The adsorption process followed the pseudo-second order kinetic model. The mass transfer model as intraparticle diffusion was applied to the experimental data to examine the mechanisms of rate controlling step. It was found that at the higher initial MB concentration, intraparticle diffusion is becoming significant controlling step. The thermodynamic constants of the adsorption process were also evaluated by using the Langmuir constants related to the equilibrium of adsorption at different temperatures. The results in this study indicated that dehydrated peanut hull was a good adsorbent for removing methylene blue.

ON THE CHEMISTRY AND STAINING PROPERTIES OF CERTAIN DERIVATIVES OF THE METHYLENE BLUE GROUP WHEN COMBINED WITH EOSIN

Science.gov (United States)

Wilson, Thomas M.

1907-01-01

1. Eosinate of thionin gives very satisfactory staining for blood smears. It is easily prepared and dissolves readily in methylated spirits. 2. In the methods heretofore employed for making mixtures of eosin and methylene blue derivatives, the eosinates of methylene violet and methylene azure are present in very small quantities or are altogether absent. 3. Thionol and thionin are probably formed in methylene blue which has been long boiled with dilute alkalies and silver oxide. 4. Good stains of eosin and methylene blue derivatives can be obtained by a variety of manipulations. 5. Methylated spirits is more economical as a solvent for this stain and better adapted for the simple technique above described than is methyl alcohol. There is some evidence that the staining act is of a chemical nature. PMID:19867116

Dystrophic calcification in muscles of legs in calcinosis, Raynaud's phenomenon, esophageal dysmotility, sclerodactyly, and telangiectasia syndrome: Accurate evaluation of the extent with 99mTc-methylene diphosphonate single photon emission computed tomography/computed tomography

International Nuclear Information System (INIS)

Chakraborty, Partha Sarathi; Karunanithi, Sellam; Dhull, Varun Singh; Kumar, Kunal; Tripathi, Madhavi

2015-01-01

We present the case of a 35-year-old man with calcinosis, Raynaud's phenomenon, esophageal dysmotility, sclerodactyly and telangiectasia variant scleroderma who presented with dysphagia, Raynaud's phenomenon and calf pain. 99m Tc-methylene diphosphonate bone scintigraphy was performed to identify the extent of the calcification. It revealed extensive dystrophic calcification in the left thigh and bilateral legs which was involving the muscles and was well-delineated on single photon emission computed tomography/computed tomography. Calcinosis in scleroderma usually involves the skin but can be found in deeper periarticular tissues. Myopathy is associated with a poor prognosis

Corneal edema and permanent blue discoloration of a silicone intraocular lens by methylene blue.

Science.gov (United States)

Stevens, Scott; Werner, Liliana; Mamalis, Nick

2007-01-01

To report a silicone intraocular lens (IOL) stained blue by inadvertent intraoperative use of methylene blue instead of trypan blue and the results of experimental staining of various lens materials with different concentrations of the same dye. A "blue dye" was used to enhance visualization during capsulorhexis in a patient undergoing phacoemulsification with implantation of a three-piece silicone lens. Postoperatively, the patient presented with corneal edema and a discolored IOL. Various IOL materials were experimentally stained using methylene blue. Sixteen lenses (4 silicone, 4 hydrophobic acrylic, 4 hydrophilic acrylic, and 4 polymethylmethacrylate) were immersed in 0.5 mL of methylene blue at concentrations of 1%, 0.1%, 0.01%, and 0.001%. These lenses were grossly and microscopically evaluated for discoloration 6 and 24 hours after immersion. The corneal edema resolved within 1 month after the initial surgical procedure. After explantation, gross and microscopic analyses of the explanted silicone lens revealed that its surface and internal substance had been permanently stained blue. In the experimental study, all of the lenses except the polymethylmethacrylate lenses were permanently stained by methylene blue. The hydrophilic acrylic lenses showed the most intense blue staining in all dye concentrations. This is the first clinicopathological report of IOL discoloration due to intraocular use of methylene blue. This and other tissue dyes may be commonly found among surgical supplies in the operating room and due diligence is necessary to avoid mistaking these dyes for those commonly used during ocular surgery.

Batch Adsorption Study of Methylene Blue in Aqueous Solution ...

African Journals Online (AJOL)

PROF HORSFALL

of methylene blue (azo dye) from the synthetic industrial wastewater was investigated in a batch system. Rice husk and coconut shell were ... the textiles, rubber, paper, plastics, cosmetic, and .... wastewater by. Fenton's oxidation: Kinetic study.

Removal of Methylene Blue from aqueous solution using spent bleaching earth

Science.gov (United States)

Saputra, E.; Saputra, R.; Nugraha, M. W.; Irianty, R. S.; Utama, P. S.

2018-04-01

The waste from industrial textile waste is one of the environmental problems, it is required effective and efficient processing. In this study spent bleaching earth was used as absorbent. It was found that the absorbent was effective to remove methylene blue from aqueous solution with removal efficiency 99.97 % in 120 min. Several parameters such as pH, amount of absorbent loading, stirring speed are found as key factor influencing removal of methylene blue. The mechanism of adsorption was also studied, and it was found that Langmuir isotherm fitted to data of experiment with adsorption capacity 0.5 mg/g.

Protective effect of methanol-methylene chloride extract of ...

African Journals Online (AJOL)

Purpose: Terminalia glaucescens (Combretaceae) is traditionally used in Cameroon in the treatment of diabetes. The anti-hyperglycemic effect of the methanol-methylene chloride extract of the leaves of this plant was investigated in streptozotocin (STZ)-induced diabetic mice. Methods: Diabetes was induced in mice by a ...

Potential adsorption of methylene blue from aqueous solution using green macroalgaePosidonia oceanica.

Science.gov (United States)

Allouche, F.-N.; Yassaa, N.

2018-03-01

The use of inexpensive biological materials, such as marine algae for removing dyes from contaminated industrial effluents appears as a potential alternative method. The aim of this study is to investigate the aptitude of marine macroalgae Posidonia Oceanica local biomass abundant on the coasts of Algeria for selective sorption of methylene blue (MB) from an aqueous solution in batch experiments at 20 °C. A maximum percentage removal of Posidonia oceanica occurs at pH 5. Equilibrium isotherm data were analyzed using the Langmuir and the Freundlich isotherms. The adsorption equilibrium of methylene blue was best describe by Langmuir model than the Freundlich model. The maximum sorption capacity was 357 mgg-1at pH 5. The sorption data were very well described by the pseudo-second-order model. Keywords: Posidonia oceanica, Methylene blue (MB), Biosorption, Isotherm Equilibrium, Kinetics; Modelling.

[Attaching single- and multi-unit fixed dental prostheses

NARCIS (Netherlands)

Kreulen, C.M.; Wolke, J.G.C.; Baat, C. de; Creugers, N.H.J.

2013-01-01

A single- or multi-unit fixed dental prosthesis can be attached to the abutment teeth through mechanical retention and gap sealing or by adhesion. For sealing the gap, water-soluble cements are appropriate, such as zinc phosphate, polycarboxylate, and (resin-modified) glasionomer cement. Attachment

Application of AlMCM-41 for competitive adsorption of methylene blue and rhodamine B: Thermodynamic and kinetic studies

International Nuclear Information System (INIS)

Eftekhari, S.; Habibi-Yangjeh, A.; Sohrabnezhad, Sh.

2010-01-01

AlMCM-41 was applied for adsorption of methylene blue (MB) and rhodamine B (RB) in single and binary component systems. In the single component systems, AlMCM-41 represents higher adsorption capacity for MB than RB with the maximal adsorption capacity of 2.08 x 10 -4 and 8.74 x 10 -5 mol/g at 25 deg. C for MB and RB, respectively. In the binary component system, MB and RB exhibit competitive adsorption onto the adsorbent. The adsorption is approximately reduced to 94 and 79% of single component adsorption systems for MB and RB (initial concentration of 8 x 10 -6 M) at 25 deg. C. In single and binary component systems, kinetic and adsorption isotherm studies demonstrate that the data are following pseudo-second-order kinetic model and Langmuir isotherm. Effect of solution pH on the adsorption in single and binary component systems was studied and the results were described by electrostatic interactions.

A nonradioactive assay for poly(a)-specific ribonuclease activity by methylene blue colorimetry.

Science.gov (United States)

Cheng, Yuan; Liu, Wei-Feng; Yan, Yong-Bin; Zhou, Hai-Meng

2006-01-01

A simple nonradioactive assay, which was based on the specific shift of the absorbance maximum of methylene blue induced by its intercalation into poly(A) molecules, was developed for poly(A)-specific ribonuclease (PARN). A good linear relationship was found between the absorbance at 662 nm and the poly(A) concentration. The assay conditions, including the concentration of methylene blue, the incubation temperature and time, and the poly(A) concentration were evaluated and optimized.

Methylene blue MMX® tablets for chromoendoscopy. Bioavailability, colon staining and safety in healthy volunteers undergoing a full colonoscopy.

Science.gov (United States)

Di Stefano, A F D; Radicioni, M M; Vaccani, A; Fransioli, A; Longo, L; Moro, L; Repici, A

2018-06-01

Methylene blue-MMX® tablets are proposed as an aid for detection and visualisation of adenomas and carcinomas in patients undergoing colonoscopy, by improving their detection rate and highlighting the presence of the intestinal dysplastic lesions. Single total doses of 100 and 200 mg were administered to healthy volunteers undergoing a bowel cleansing preparation and a full colonoscopy to investigate the colonic staining. The pharmacokinetics of methylene blue and the safety after exposure to the tablets were also investigated. With 200 mg, the best staining, assessed as the sum of acceptable and good staining, was achieved in the ascending colon and rectosigmoid (75% subjects each), the transverse and the descending colon (approximately 63% each). Absence of staining or overstaining were reported for no colonic region of interest in any subject. Similar results were observed in the 100 mg dose group. Methylene blue blood concentrations reached a peak (C max ) in a median time (T max ) of 12 h with 100 mg and 16 h with 200 mg. AUC 0-t was 10.7 ± 6.7 μg/mLxh after 100 mg and 25.2 ± 7.4 μg/mLxh after 200 mg. Half-life ranged between 9 and 22 h after the lower dose and between 6 and 26 h after the higher dose. The cumulative excretion was about 28% after 100 mg and about 39% after 200 mg. The overall frequency of adverse events was 39%, but only one was related to the product: abnormal transaminases. The most frequent adverse event was a transient polyuria (17%). One serious adverse event (gastrointestinal haemorrhage) led the subject to study discontinuation and hospitalisation and another subject withdrew the study due to one adverse event (haematemesis). Either event was not related to methylene blue. Copyright © 2017. Published by Elsevier Inc.

Methylene blue (cationic dye) adsorption into Salvadora persica ...

African Journals Online (AJOL)

Methylene blue (MB) is the most commonly used substance for dyeing cotton, wood and silk. On inhalation, it can cause difficulty in breathing, while on direct contact, it may cause permanent injury of the eyes of human and animals, burning sensations, nausea, worming, profuse sweating, mental confusion and ...

Magnetic graphene sponge for the removal of methylene blue

International Nuclear Information System (INIS)

Yu, Baowei; Zhang, Xiaoliang; Xie, Jingru; Wu, Ruihan; Liu, Xiaoyang; Li, Hongliang; Chen, Fang; Yang, Hua; Ming, Zhu; Yang, Sheng-Tao

2015-01-01

Graphical abstract: - Highlights: • Magnetic graphene sponge is prepared for dye removal in aqueous solution. • Magnetic graphene sponge has an adsorption capacity of 526 mg/g for methylene blue. • Adsorption behaviors of methylene blue on magnetic graphene sponge are investigated. • Magnetic graphene sponge could be partially regenerated by washing with acidic ethanol. - Abstract: Magnetic carbon nanomaterials have been widely adopted as adsorbents in water treatment, but the low adsorption capacities largely limit their practical applications. In this study, magnetic graphene sponge (Fe 3 O 4 -GS) was prepared by lyophilization for the adsorption of dye pollutant. The incorporation of Fe 3 O 4 enabled the magnetic separation of Fe 3 O 4 -GS after the adsorption of methylene blue (MB). The adsorption capacity of Fe 3 O 4 -GS for MB was 526 mg/g, much higher than those of the magnetic carbon nanoadsorbents in the literature. The adsorption kinetics of MB on Fe 3 O 4 -GS was moderately fast, which could be analyzed by the pseudo-second-order model and intraparticle diffusion model. The thermodynamics study revealed that the adsorption was driven by the increased randomness on the interface. The pH and ionic strength had meaningful influences on the adsorption capacity of Fe 3 O 4 -GS. The facile regeneration of Fe 3 O 4 -GS would definitely reduce its operating cost. The implications to the environmental applications of magnetic carbon nanoadsorbents are discussed

Carbon and TiO_2 synergistic effect on methylene blue adsorption

International Nuclear Information System (INIS)

Simonetti, Evelyn Alves Nunes; Simone Cividanes, Luciana de; Campos, Tiago Moreira Bastos; Rossi Canuto de Menezes, Beatriz; Brito, Felipe Sales; Thim, Gilmar Patrocínio

2016-01-01

Due to its high efficiency, low cost and a simple operation, the adsorption process is an important and widely used technique for industrial wastewater treatment. Recent studies on the removal of artificial dyes by adsorption include a large number of adsorbents, such as: activated carbon, silicates, carbon nanotube, graphene, fibers, titanates and doped titanates. The carbon insertion in the TiO_2 structure promotes a synergistic effect on the adsorbent composite, improving the adsorption and the charge-transfer efficiency rates. However, there are few studies regarding the adsorption capacity of TiO_2/Carbon composites with the carbon concentration. This study evaluates the effect of carbon (resorcinol/formaldehyde) insertion on TiO_2 structure through the adsorption process. Adsorbents were prepared by varying the carbon weight percentages using the sol-gel method. The physicochemical properties of the catalysts prepared, such as crystallinity, particle size, surface morphology, specific surface area and pore volume were investigated. The kinetic study, adsorption isotherm, pH effect and thermodynamic study were examined in batch experiments using methylene blue as organic molecule. In addition, the effect of carbon phase on the adsorption capacity of TiO_2-carbon composite was deeply investigated. SEM micrographs showed that TiO_2 phase grows along the carbon phase and FT-IR results showed the presence of Ti−O−C chemical bonding. The experiments indicate that the carbon phase acted as a nucleation agent for the growth of TiO_2 during the sol-gel step, with a TiO_2 structure suitable for blue methylene adsorption, resulting in a material with large surface area and slit-like or wedge-shaped pores. Further experiments will show the best carbon concentration for methylene blue adsorption using a TiO_2 based material. - Highlights: • This article deals with the adsorption of methylene blue onto TiO_2-Carbon composite. • The sol-gel synthesis was efficient

Photodynamic action of the methylene blue: mutagenesis and sinergism

International Nuclear Information System (INIS)

Capella, M.A.M.

1988-01-01

Two aspects of photodynamic therapy were studied: the associated mutagenesis and the interactions with physical agents, in order to increase its biological effects. The photodynamic action with methylene blue in the mutagenesis and sinergism is studied. (L.M.J.)

Sunlight-Induced Photochemical Degradation of Methylene Blue by Water-Soluble Carbon Nanorods

Directory of Open Access Journals (Sweden)

Anshu Bhati

2016-01-01

Full Text Available Water-soluble graphitic hollow carbon nanorods (wsCNRs are exploited for their light-driven photochemical activities under outdoor sunlight. wsCNRs were synthesized by a simple pyrolysis method from castor seed oil, without using any metal catalyst or template. wsCNRs exhibited the light-induced photochemical degradation of methylene blue used as a model pollutant by the generation of singlet oxygen species. Herein, we described a possible degradation mechanism of methylene blue under the irradiation of visible photons via the singlet oxygen-superoxide anion pathway.

[Sensitive determination of Bi3+ by spectrofluorimetry based on graphene oxide-methylene blue system].

Science.gov (United States)

Zhai, Qiu-ge; Guo, Peng; Zhou, Lin; Liu, Yan-ming

2014-08-01

Graphene oxide was prepared by the modified Hummers method and characterized by field emission scanning electron microscopy. The interaction of graphene with methylene blue was studied by UV absorption, the intensity of two main absorption peaks of methylene blue decreased significantly after the fluorescence was quenched, and the energy transfer didn't occur because the overlap of the absorption spectrum of GO and the emission spectrum of MB is too small. Therefore, the fluorescence quenching of MB and GO was static. When adding a certain amount of Bi3+ in the graphene-methylene blue system, Bi3+ replaces the methylene blue from the graphene-methylene blue complexes because Bi3+ has the smaller volume and is more positively charged. The methylene blue therefore dissociates from the GO-MB complexes, resulting in the recovery of fluorescence of the system. Furthermore, the fluorescence of the system increases with the increase in the amount of Bi3+ due to the enhanced amount of MB in the system. A novel spectrofluorimetric method was therefore developed for the sensitive determination of Bi3+. Some parameters including the concentration of methylene blue, the amount of graphene oxide, the amount of nitric acid and the sequence of reagent adding were optimized to obtain higher sensitivity. The fluorescence of the system was detected at an emission wavelength of 667 nm with excitation at 690 nm. Under the optimized conditions, the concentration of Bi3+ showed good linear relationships with the fluorescence intensity in the range of 0.5-100 micromol x L(-1), with correlation coefficients of r = 0.9955. The limits of detection for Bi3+ was 1.0 x 10(-8) mol x L(-1) (S/N=3). The selectivity of the proposed method was evaluated and the results showed that 1000-fold K+, Ca+, Na+, Mg2+, Cu2+; 100-fold Fe3+, Be2+, SiO2- Al3+, Ni2+, Sb3+, NO3-, Cl-, F-, and 20-fold Pb2+, Hg2+, Cd2+ had negligible interference with the determination of Bi3+. The method has advantages of

Chemical composition effects of methylene containing polymers on gas emission under γ-irradiation

Energy Technology Data Exchange (ETDEWEB)

Ferry, M., E-mail: muriel.ferry@cea.fr [CEA, DEN, DPC, SECR, LRMO, F-91191 Gif-sur-Yvette (France); Dannoux-Papin, A. [CEA, DEN, DPC, SECR, LRMO, F-91191 Gif-sur-Yvette (France); Dély, N. [CEA, DSM, IRAMIS, LIDYL, PCR, F-91191 Gif-sur-Yvette (France); Legand, S.; Durand, D.; Roujou, J.L.; Lamouroux, C.; Dauvois, V. [CEA, DEN, DPC, SECR, LRMO, F-91191 Gif-sur-Yvette (France); Coignet, P.; Cochin, F. [AREVA NC DOR/RDP, 1 place Jean Millier, 92084 La Défense (France); Esnouf, S. [CEA, DEN, DPC, SECR, LRMO, F-91191 Gif-sur-Yvette (France); CEA, DSM, IRAMIS, LIDYL, PCR, F-91191 Gif-sur-Yvette (France)

2014-09-01

The presence of different chemical groups in methylene containing polymers can lead to very different behaviors under ionizing radiation. To better understand the effect of these groups on gas production under γ-irradiation, especially on hydrogen formation, and to study the efficiency of energy transfer between chemical groups, several methylene containing polymers with different controlled group concentrations were studied in inert atmosphere. We analyzed the influence of the nature and position of the chemical group using methylene containing copolymers with aliphatic side-chains (different lengths), ester groups in the side-chains (different concentrations) and ester groups in the polymer backbone (different concentrations). Radiation chemical yields of H{sub 2}, CO, CO{sub 2} and CH{sub 4} were determined at room temperature by high resolution mass spectrometry. On the basis of these results, we attempt to obtain a better understanding of the mechanisms involved. It can be observed that crystallinity and aliphatic side-chain have no effect on hydrogen formation. On contrary, esters on side-chain and in the backbone have an important influence on hydrogen formation, with the most important effect when esters groups are in the backbone. In these two kind of materials, energy fraction transferred from methylene to ester groups has been quantified and only 10 wt% (or less) of ester groups are sufficient to protect effectively the aliphatic moiety.

Magnetic graphene sponge for the removal of methylene blue

Energy Technology Data Exchange (ETDEWEB)

Yu, Baowei; Zhang, Xiaoliang; Xie, Jingru; Wu, Ruihan; Liu, Xiaoyang; Li, Hongliang; Chen, Fang; Yang, Hua; Ming, Zhu; Yang, Sheng-Tao, E-mail: yangst@pku.edu.cn

2015-10-01

Graphical abstract: - Highlights: • Magnetic graphene sponge is prepared for dye removal in aqueous solution. • Magnetic graphene sponge has an adsorption capacity of 526 mg/g for methylene blue. • Adsorption behaviors of methylene blue on magnetic graphene sponge are investigated. • Magnetic graphene sponge could be partially regenerated by washing with acidic ethanol. - Abstract: Magnetic carbon nanomaterials have been widely adopted as adsorbents in water treatment, but the low adsorption capacities largely limit their practical applications. In this study, magnetic graphene sponge (Fe{sub 3}O{sub 4}-GS) was prepared by lyophilization for the adsorption of dye pollutant. The incorporation of Fe{sub 3}O{sub 4} enabled the magnetic separation of Fe{sub 3}O{sub 4}-GS after the adsorption of methylene blue (MB). The adsorption capacity of Fe{sub 3}O{sub 4}-GS for MB was 526 mg/g, much higher than those of the magnetic carbon nanoadsorbents in the literature. The adsorption kinetics of MB on Fe{sub 3}O{sub 4}-GS was moderately fast, which could be analyzed by the pseudo-second-order model and intraparticle diffusion model. The thermodynamics study revealed that the adsorption was driven by the increased randomness on the interface. The pH and ionic strength had meaningful influences on the adsorption capacity of Fe{sub 3}O{sub 4}-GS. The facile regeneration of Fe{sub 3}O{sub 4}-GS would definitely reduce its operating cost. The implications to the environmental applications of magnetic carbon nanoadsorbents are discussed.

Methylene blue improves mitochondrial respiration and decreases oxidative stress in a substrate-dependent manner in diabetic rat hearts.

Science.gov (United States)

Duicu, Oana M; Privistirescu, Andreea; Wolf, Adrian; Petruş, Alexandra; Dănilă, Maria D; Raţiu, Corina D; Muntean, Danina M; Sturza, Adrian

2017-11-01

Diabetic cardiomyopathy has been systematically associated with compromised mitochondrial energetics and increased generation of reactive oxygen species (ROS) that underlie its progression to heart failure. Methylene blue is a redox drug with reported protective effects mainly on brain mitochondria. The purpose of the present study was to characterize the effects of acute administration of methylene blue on mitochondrial respiration, H 2 O 2 production, and calcium sensitivity in rat heart mitochondria isolated from healthy and 2 months (streptozotocin-induced) diabetic rats. Mitochondrial respiratory function was assessed by high-resolution respirometry. H 2 O 2 production and calcium retention capacity were measured spectrofluorimetrically. The addition of methylene blue (0.1 μmol·L -1 ) elicited an increase in oxygen consumption of mitochondria energized with complex I and II substrates in both normal and diseased mitochondria. Interestingly, methylene blue elicited a significant increase in H 2 O 2 release in the presence of complex I substrates (glutamate and malate), but had an opposite effect in mitochondria energized with complex II substrate (succinate). No changes in the calcium retention capacity of healthy or diabetic mitochondria were found in the presence of methylene blue. In conclusion, in cardiac mitochondria isolated from diabetic and nondiabetic rat hearts, methylene blue improved respiratory function and elicited a dichotomic, substrate-dependent effect on ROS production.

Uptake and localization of sup(99m)technetium-methylene-diphosphonate in bone

International Nuclear Information System (INIS)

Savelkoul, T.J.F.

1984-01-01

The author investigated the uptake and localization of 99m-technetium-methylene-diphosphonate (99m-Tc-MDP) in bone, to develop a sensitive mean for the detection of early osseous disease. In an electrolysis procedure without the presence of contaminating reductants a 99m-Tc-MDP complex is formed with clear bone-seeking properties. The scans performed in experimental animals are comparable in quality with 99m-Tc(Sn)-MDP scans. The uptake of 99m-Tc-MDP is faster and higher than the uptake of reduced hydrolyzed 99m-Tc. Uptake of 99m-Tc(Sn)-MDP in bone can only take place after decomposition of the complex. As 99m-Tc-MDP is taken up as a unit, this may be a better agent to evaluate the osteoblastic activity in the skeleton. (Auth./R.B.)

Occupational methaemoglobinaemia. Mechanisms of production, features, diagnosis and management including the use of methylene blue.

Science.gov (United States)

Bradberry, Sally M

2003-01-01

unreliable in the presence of methaemoglobinaemia. Arterial blood gas analysis is mandatory in severe poisoning and reveals normal partial pressures of oxygen (pO2) and carbon dioxide (pCO2,), a normal 'calculated' haemoglobin oxygen saturation, an increased methaemoglobin concentration and possibly a metabolic acidosis. Following decontamination, high-flow oxygen should be given to maximise oxygen carriage by remaining ferrous haem. No controlled trial of the efficacy of methylene blue has been performed but clinical experience suggests that methylene blue can increase the rate of methaemoglobin conversion to haemoglobin some 6-fold. Patients with features and/or methaemoglobin concentrations of 30-50%, should be administered methylene blue 1-2 mg/kg/bodyweight intravenously (the dose depending on the severity of the features), whereas those with methaemoglobin concentrations exceeding 50% should be given methylene blue 2 mg/kg intravenously. Symptomatic improvement usually occurs within 30 minutes and a second dose of methylene blue will be required in only very severe cases or if there is evidence of ongoing methaemoglobin formation. Methylene blue is less effective or ineffective in the presence of glucose-6-phosphate dehydrogenase deficiency since its antidotal action is dependent on nicotinamide-adenine dinucleotide phosphate (NADP+). In addition, methylene blue is most effective in intact erythrocytes; efficacy is reduced in the presence of haemolysis. Moreover, in the presence of haemolysis, high dose methylene blue (20-30 mg/kg) can itself initiate methaemoglobin formation. Supplemental antioxidants such as ascorbic acid (vitamin C), N-acetylcysteine and tocopherol (vitamin E) have been used as adjuvants or alternatives to methylene blue with no confirmed benefit. Exchange transfusion may have a role in the management of severe haemolysis or in G-6-P-D deficiency associated with life-threatening methaemoglobinaemia where methylene blue is relatively contraindicated.

Mass transfer ranking of polylysine, poly-ornithine and poly-methylene-co-guanidine microcapsule membranes using a single low molecular mass marker

Directory of Open Access Journals (Sweden)

Rosinski Stefan

2003-01-01

Full Text Available On the long way to clinical transplantable hybrid systems, comprising of cells, acting as immuno-protected bioreactors microencapsulated in a polymeric matrix and delivering desired factors (proteins, hormones, enzymes etc to the patient's body, an important step is the optimization of the microcapsule. This topic includes the selection of a proper coating membrane which could fulfil, first of all, the mass transfer as well as biocompatibility, stability and durability requirements. Three different membranes from polymerised aminoacids, formed around exactly identical alginate gel cores, were considered, concerning their mass transport properties, as potential candidates in this task. The results of the evaluation of the mass ingress and mass transfer coefficient h for the selected low molecular mass marker, vitamin B12, in poly-L-lysine (HPLL poly-L-ornithine (HPLO and poly-methylene-co-guanidine hydrochloride (HPMCG membrane alginate microcapsules demonstrate the advantage of using the mass transfer approach to a preliminary screening of various microcapsule formulations. Applying a single marker and evaluating mass transfer coefficients can help to quickly rank the investigated membranes and microcapsules according to their permeability. It has been demonstrated that HPLL, HPLO and HPMCG microcapsules differ from each other by a factor of two concerning the rate of low molecular mass marker transport. Interesting differences in mass transfer through the membrane in both directions in-out was also found, which could possibly be related to the membrane asymmetry.

Single-unit studies of visual motion processing in cat extrastriate areas

NARCIS (Netherlands)

Vajda, Ildiko

2003-01-01

Motion vision has high survival value and is a fundamental property of all visual systems. The old Greeks already studied motion vision, but the physiological basis of it first came under scrutiny in the late nineteenth century. Later, with the introduction of single-cell (single-unit)

Methylene blue adsorption by algal biomass based materials: biosorbents characterization and process behaviour.

Science.gov (United States)

Vilar, Vítor J P; Botelho, Cidália M S; Boaventura, Rui A R

2007-08-17

Dead algal biomass is a natural material that serves as a basis for developing a new family of sorbent materials potentially suitable for many industrial applications. In this work an algal industrial waste from agar extraction process, algae Gelidium and a composite material obtained by immobilization of the algal waste with polyacrylonitrile (PAN) were physical characterized and used as biosorbents for dyes removal using methylene blue as model. The apparent and real densities and the porosity of biosorbents particles were determined by mercury porosimetry and helium picnometry. The methylene blue adsorption in the liquid phase was the method chosen to calculate the specific surface area of biosorbent particles as it seems to reproduce better the surface area accessible to metal ions in the biosorption process than the N2 adsorption-desorption dry method. The porous texture of the biosorbents particles was also studied. Equilibrium isotherms are well described by the Langmuir equation, giving maximum uptake capacities of 171, 104 and 74 mg g(-1), respectively for algae, algal waste and composite material. Kinetic experiments at different initial methylene blue concentrations were performed to evaluate the equilibrium time and the importance of the driving force to overcome mass transfer resistances. The pseudo-first-order and pseudo-second-order kinetic models adequately describe the kinetic data. The biosorbents used in this work proved to be promising materials for removing methylene blue from aqueous solutions.

The Adsorption Efficiency of Chemically Prepared Activated Carbon from Cola Nut Shells by on Methylene Blue

Directory of Open Access Journals (Sweden)

Julius Ndi Nsami

2013-01-01

Full Text Available The adsorption of methylene blue from aqueous solution onto activated carbon prepared from cola nut shell has been investigated under batch mode. The influence of major parameters governing the efficiency of the process such as, solution pH, sorbent dose, initial concentration, and contact time on the removal process was investigated. The time-dependent experimental studies showed that the adsorption quantity of methylene blue increases with initial concentration and decreasing adsorbent dosage. The equilibrium time of 180 min was observed and maximum adsorption was favoured at pH 3.5. The dye removal using 0.1 g of adsorbent was more than 90%. This dosage (0.1 g was considered as the optimum dosage to remove methylene blue from aqueous solutions. The equilibrium adsorption data were analyzed by the Freundlich, Langmuir adsorption isotherm models. The kinetics of methylene blue solution was discussed by pseudo-first-order, pseudo-second-order, and Elovich models. The adsorption process follows the Elovich rate kinetic model, having a correlation coefficient in the range between 0.9811 and 1.

Sorption study of methylene blue on activated carbon prepared from Jatropha curcas and Terminalia catappa seed coats

Directory of Open Access Journals (Sweden)

Ismaila Olalekan Saheed

2016-12-01

Full Text Available This research work targets the effectiveness of the prepared activated carbon from Jatropha curcas and Terminalia catappa seed coats for the sorption of methylene blue (MB from aqueous solution. The prepared Jatropha activated carbon (JAC and Terminalia activated carbon (TAC were characterised using Fourier transform infrared spectroscopy (FTIR, Scanning electron microscopy (SEM and Branauer- Emmett-Teller (BET surface area analysis. Effect of initial concentration, pH, contact time, adsorbent dose and temperature on the sorption experiments were studied and the adsorption capacity of these adsorbents were found to be 37.84 mg/g and 17.44 mg/g for methylene blue uptake by JAC and TAC respectively. The experimental data were analysed using Langmuir, Fruendlich, and Dubinin-Radushkevich isotherms. The data fitted best into Langmuir isotherm for Methylene blue-JAC and Methylene blue-TAC systems. The kinetic studies fitted into pseudo second order kinetics model. The process chemistry was exothermic.

Viability of the Fricke dosemeter doped with methylene blue

International Nuclear Information System (INIS)

Souza, V.L.B.; Santos, C.D.A.; Rodrigues, K.R.G.; Cunha, M.S.; Figueiredo, M.D.C.; Melo, R.T.

2009-01-01

This work aims to find the possible utilization of the Fricke dosemeter doped with methylene blue (FMB) for the dosimetry of photodynamic therapy. The FMB was irradiated wit X rays and light emitted diodes demonstrating positive answers to the stimulus, being probably to be used for dosimetric objectives

Sorption characteristics of methylene blue onto Nypa fruiticans lignin ...

African Journals Online (AJOL)

The sorption characteristics of soda lignin extracted from Nypa fruiticans for the removal of methylene blue dye from aqueous solution was investigated in this study, as an ethically sound way of utilizing this unexploited abundant natural resource. Equilibrium data were fitted to the Langmuir and Freundlich isotherm ...

Kinetics of tissue distribution and elimination of 4,4'-methylene bis(2-chloroaniline) in rats

International Nuclear Information System (INIS)

Tobes, M.C.; Brown, L.E.; Chin, B.; Marsh, D.D.

1983-01-01

The tissue distribution kinetics and elimination of 4,4'-methylene bis(2-chloroaniline) (MBOCA) in rats was studied after a single dose of [ 14 C]MBOCA (0.49 mg/kg body weight, i.v.). The highest concentrations of radioactivity were in the small intestine, liver, adipose, lung, kidney, skin, and adrenals. For most tissues, a rapid decrease in radioactivity was followed by a slower decrease except for the small intestine, adipose and skin which demonstrated transient increases. Subcellular distribution in liver at 1 h showed radioactivity in all cell fractions. Although very lipophilic, [ 14 C]MBOCA was completely eliminated within 48 h with the major route via the feces (73.4%). (Auth.)

IRIS Toxicological Review of Dichloromethane (Methylene ...

Science.gov (United States)

EPA has finalized the Toxicological Review of Dichloromethane (Methylene Chloride): In support of the Integrated Risk Information System (IRIS). Now final, this assessment may be used by EPA’s program and regional offices to inform decisions to protect human health. This document presents background information and justification for the Intergrated Risk Information System (IRIS) Summary of the hazard and dose-response assessment of dichloromethane. IRIS Summaries may include oral reference dose (RfD) and inhalation reference concentration (RfC) values for chronic and other exposure durations, and a carcinogencity assessment. Internet/NCEA web site

Permeation of lysosomal membranes in the course of photo-sensitization with methylene blue and hematoporphyrin: study by cellular microspectrofluorometry

International Nuclear Information System (INIS)

Santus, R.; Kohen, C.; Kohen, E.; Morliere, P.; Dubertret, L.; Tocci, P.M.

1983-01-01

The photodynamically-induced liberation of lysosomal enzymes using β-galactosidase as marker for the lysosomal enzymes has been studied by microspectrofluorometry on mouse L cells. Similar studies have been carried out using N-acetyl-β-glucosaminidase as marker for the lysosomal enzymes of human fibroblasts. The high sensitivity of the fluorescence detection makes it possible to use 4-methylumbelliferyl substrates for the enzymes contained in a single cell. Methylene blue and hematoporphyrin readily incorporate into both cells and upon excitation, sensitize lysosomal membrane damages, leading to enzyme release accompanying strong morphological changes. (author)

Radiolysis of methylene blue studied by ESR

International Nuclear Information System (INIS)

Contineau, M.; Iliescu, C.; Ciureanu, M.

1983-01-01

Electron spin resonance spectra have been used to gain information on the mechanism of radiolysis of aqueous solutions of methylene blue. The identity and behaviour of the semiquinone radicals formed as intermediate reduction products were discussed for strongly acid and for alcaline solutions. In order to obtain information on the radiolytic mechanism in strongly acidic media, irradiation was performed in the presence of various types of scavengers: sodium formate, glucose, succinic acid, hydroquinone and D,L-α alanine. (author)

Splitting Terraced Houses Into Single Units Using Oblique Aerial Imagery

Science.gov (United States)

Dahlke, D.

2017-05-01

This paper introduces a method to subdivide complex building structures like terraced houses into single house units comparable to units available in a cadastral map. 3D line segments are detected with sub-pixel accuracy in traditional vertical true orthomosaics as well as in innovative oblique true orthomosaics and their respective surface models. Hereby high gradient strengths on roofs as well as façades are taken into account. By investigating the coplanarity and frequencies within a set of 3D line segments, individual cut lines for a building complex are found. The resulting regions ideally describe single houses and thus the object complexity is reduced for subsequent topological, semantical or geometrical considerations. For the chosen study area with 70 buidling outlines a hit rate of 80% for cut lines is achieved.

Evaluation of anticancer properties of a new α-methylene-δ-lactone DL-249 on two cancer cell lines

Directory of Open Access Journals (Sweden)

Pomorska Dorota K.

2017-06-01

Full Text Available The anticancer activity of a new synthetic α-methylene-δ-lactone DL-249 was reported in leukemia HL-60 and breast cancer MCF-7 cells and compared with the activity of a natural α-methylene-γ-lactone from Tanacetum parthenium, parthenolide.

The monoamine oxidase inhibition properties of selected structural analogues of methylene blue

International Nuclear Information System (INIS)

Delport, Anzelle; Harvey, Brian H.; Petzer, Anél; Petzer, Jacobus P.

2017-01-01

The thionine dye, methylene blue (MB), is a potent inhibitor of monoamine oxidase (MAO) A, a property that may, at least in part, mediate its antidepressant effects in humans and animals. The central inhibition of MAO-A by MB has also been linked to serotonin toxicity (ST) which may arise when MB is used in combination with serotonergic drugs. Structural analogues and the principal metabolite of MB, azure B, have also been reported to inhibit the MAO enzymes, with all compounds exhibiting specificity for the MAO-A isoform. To expand on the structure-activity relationships (SARs) of MAO inhibition by MB analogues, the present study investigates the human MAO inhibition properties of five MB analogues: neutral red, Nile blue, new methylene blue, cresyl violet and 1,9-dimethyl methylene blue. Similar to MB, these analogues also are specific MAO-A inhibitors with cresyl violet (IC 50 = 0.0037 μM), Nile blue (IC 50 = 0.0077 μM) and 1,9-dimethyl methylene blue (IC 50 = 0.018 μM) exhibiting higher potency inhibition compared to MB (IC 50 = 0.07 μM). Nile blue also represents a potent MAO-B inhibitor with an IC 50 value of 0.012 μM. From the results it may be concluded that non-thionine MB analogues (e.g. cresyl violet and Nile blue) also may exhibit potent MAO inhibition, a property which should be considered when using these compounds in pharmacological studies. Benzophenoxazines such as cresyl violet and Nile blue are, similar to phenothiazines (e.g. MB), representative of high potency MAO-A inhibitors with a potential risk of ST. - Highlights: • MB analogues, cresyl violet and Nile blue, are high potency MAO-A inhibitors. • Nile blue also represents a potent MAO-B inhibitor. • Potent MAO-A inhibition should alert to potential serotonin toxicity.

The monoamine oxidase inhibition properties of selected structural analogues of methylene blue

Energy Technology Data Exchange (ETDEWEB)

Delport, Anzelle [Pharmaceutical Chemistry, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Centre of Excellence for Pharmaceutical Sciences, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Harvey, Brian H. [Centre of Excellence for Pharmaceutical Sciences, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Pharmacology, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Petzer, Anél [Pharmaceutical Chemistry, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Centre of Excellence for Pharmaceutical Sciences, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Petzer, Jacobus P., E-mail: jacques.petzer@nwu.ac.za [Pharmaceutical Chemistry, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Centre of Excellence for Pharmaceutical Sciences, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa)

2017-06-15

The thionine dye, methylene blue (MB), is a potent inhibitor of monoamine oxidase (MAO) A, a property that may, at least in part, mediate its antidepressant effects in humans and animals. The central inhibition of MAO-A by MB has also been linked to serotonin toxicity (ST) which may arise when MB is used in combination with serotonergic drugs. Structural analogues and the principal metabolite of MB, azure B, have also been reported to inhibit the MAO enzymes, with all compounds exhibiting specificity for the MAO-A isoform. To expand on the structure-activity relationships (SARs) of MAO inhibition by MB analogues, the present study investigates the human MAO inhibition properties of five MB analogues: neutral red, Nile blue, new methylene blue, cresyl violet and 1,9-dimethyl methylene blue. Similar to MB, these analogues also are specific MAO-A inhibitors with cresyl violet (IC{sub 50} = 0.0037 μM), Nile blue (IC{sub 50} = 0.0077 μM) and 1,9-dimethyl methylene blue (IC{sub 50} = 0.018 μM) exhibiting higher potency inhibition compared to MB (IC{sub 50} = 0.07 μM). Nile blue also represents a potent MAO-B inhibitor with an IC{sub 50} value of 0.012 μM. From the results it may be concluded that non-thionine MB analogues (e.g. cresyl violet and Nile blue) also may exhibit potent MAO inhibition, a property which should be considered when using these compounds in pharmacological studies. Benzophenoxazines such as cresyl violet and Nile blue are, similar to phenothiazines (e.g. MB), representative of high potency MAO-A inhibitors with a potential risk of ST. - Highlights: • MB analogues, cresyl violet and Nile blue, are high potency MAO-A inhibitors. • Nile blue also represents a potent MAO-B inhibitor. • Potent MAO-A inhibition should alert to potential serotonin toxicity.

Removal efficiency of methylene blue using activated carbon from waste banana stem: Study on pH influence

Science.gov (United States)

Misran, E.; Bani, O.; Situmeang, E. M.; Purba, A. S.

2018-02-01

The effort to remove methylene blue in artificial solution had been conducted using adsorption process. The abundant banana stem waste was utilized as activated carbon precursor. This study aimed to analyse the influence of solution pH to removal efficiency of methylene blue using activated carbon from banana stem as adsorbent. Activated carbon from banana stem was obtained by chemical activation using H3PO4 solution. Proximate analysis result showed that the activated carbon has 47.22% of fixed carbon. This value exhibited that banana stem was a potential adsorbent precursor. Methylene blue solutions were prepared at initial concentration of 50 ppm. The influence of solution pH was investigated with the use of 0.2 g adsorbent for 100 mL dye solution. The adsorption was conducted using shaker with at a constant rate of 100 rpm at room temperature for 90 minutes. The results showed that solution pH influenced the adsorption. The activated carbon from banana stem demonstrated satisfying performance since removal efficiencies of methylene blue were higher than 99%.

Desorption and photodegradation of methylene blue from modified sugarcane bagasse surface by acid TiO2 hydrosol

International Nuclear Information System (INIS)

Yu Junxia; Chi Ruan; Guo Jia; Zhang Yuefei; Xu Zhigao; Xiao Chunqiao

2012-01-01

Waste sugarcane bagasse (SCB) was modified by pyromellitic dianhydride to improve its adsorption capacity for cationic dyes. Results showed that the adsorption capacity of the modified SCB for methylene blue was 564 mg g -1 , which was about 12 times than that obtained on the unmodified SCB. Methylene blue loaded modified SCB was regenerated by a self-clean eluent: TiO 2 hydrosol with pH ranged from 1 to 4, and HNO 3 solution with the same pH range was tested at the same time for comparison. Results showed that desorption kinetics of methylene blue in the hydrosol systems fit two-step kinetic model and controlled mainly by the slow step. As a self-clean eluent, acid hydrosol could firstly desorb and then photodegrade methylene blue under sunlight irradiation. After five desorption-photodegradation cycles, 78.3% of the absorbed dyes could be desorbed by using hydrosol (pH 2) as eluent. The hydrosol could be continuously used in desorption and photodegradation process, which would economize large volume of the eluent and moreover it would not bring secondary pollution.

Interaction mode between methylene blue-Sm(III) complex and ...

African Journals Online (AJOL)

Spectroscopic and viscosity methods were applied to investigate the interaction between methylene blue (MB)-Sm(III) complex and herring sperm DNA by using acridine orange as a spectral probe in Tris-HCl buffer (pH 7.40). By means of molar ratio method, the binding ratios between MB-Sm(III)and DNA were determined ...

Carbon and TiO{sub 2} synergistic effect on methylene blue adsorption

Energy Technology Data Exchange (ETDEWEB)

Simonetti, Evelyn Alves Nunes, E-mail: evelynalvesnunes@yahoo.com.br; Simone Cividanes, Luciana de; Campos, Tiago Moreira Bastos; Rossi Canuto de Menezes, Beatriz; Brito, Felipe Sales; Thim, Gilmar Patrocínio

2016-07-01

Due to its high efficiency, low cost and a simple operation, the adsorption process is an important and widely used technique for industrial wastewater treatment. Recent studies on the removal of artificial dyes by adsorption include a large number of adsorbents, such as: activated carbon, silicates, carbon nanotube, graphene, fibers, titanates and doped titanates. The carbon insertion in the TiO{sub 2} structure promotes a synergistic effect on the adsorbent composite, improving the adsorption and the charge-transfer efficiency rates. However, there are few studies regarding the adsorption capacity of TiO{sub 2}/Carbon composites with the carbon concentration. This study evaluates the effect of carbon (resorcinol/formaldehyde) insertion on TiO{sub 2} structure through the adsorption process. Adsorbents were prepared by varying the carbon weight percentages using the sol-gel method. The physicochemical properties of the catalysts prepared, such as crystallinity, particle size, surface morphology, specific surface area and pore volume were investigated. The kinetic study, adsorption isotherm, pH effect and thermodynamic study were examined in batch experiments using methylene blue as organic molecule. In addition, the effect of carbon phase on the adsorption capacity of TiO{sub 2}-carbon composite was deeply investigated. SEM micrographs showed that TiO{sub 2} phase grows along the carbon phase and FT-IR results showed the presence of Ti−O−C chemical bonding. The experiments indicate that the carbon phase acted as a nucleation agent for the growth of TiO{sub 2} during the sol-gel step, with a TiO{sub 2} structure suitable for blue methylene adsorption, resulting in a material with large surface area and slit-like or wedge-shaped pores. Further experiments will show the best carbon concentration for methylene blue adsorption using a TiO{sub 2} based material. - Highlights: • This article deals with the adsorption of methylene blue onto TiO{sub 2}-Carbon

Shaping the breast in secondary microsurgical breast reconstruction: single- vs. two-esthetic unit reconstruction.

Science.gov (United States)

Gravvanis, Andreas; Smith, Roger W

2010-10-01

The esthetic outcome is dictated essentially not only by the position, size, and shape of the reconstructed breast, but also by the extra scaring involved. In the present study, we conducted a visual analog scale survey to compare the esthetic outcome in delayed autologous breast reconstruction following two different abdominal flaps inset. Twenty-five patients had their reconstruction using the Single-esthetic Unit principle and were compared with 25 patients that their breast was reconstructed using the Two-Esthetic Unit principle. Photographic images were formulated to a PowerPoint presentation and cosmetic outcomes were assessed from 30 physicians, by means of a Questionnaire and a visual analog scale. Our data showed that the single-esthetic unit breast reconstruction presents significant advantages over the traditional two-esthetic units, due to inconspicuous flap reconstruction, better position of the inframammary fold, and more natural transition from native and reconstructed tissues. Moreover, patient self-evaluation of esthetic outcome and quality of life showed that single-esthetic unit reconstruction is associated with higher patient satisfaction, therefore should be considered the method of choice. © 2010 Wiley-Liss, Inc.

Kinetics of tissue distribution and elimination of 4,4'-methylene bis(2-chloroaniline) in rats

Energy Technology Data Exchange (ETDEWEB)

Tobes, M.C.; Brown, L.E.; Chin, B.; Marsh, D.D. (Michigan Univ., Ann Arbor (USA). Medical Center)

1983-06-01

The tissue distribution kinetics and elimination of 4,4'-methylene bis(2-chloroaniline) (MBOCA) in rats was studied after a single dose of (/sup 14/C)MBOCA (0.49 mg/kg body weight, i.v.). The highest concentrations of radioactivity were in the small intestine, liver, adipose, lung, kidney, skin, and adrenals. For most tissues, a rapid decrease in radioactivity was followed by a slower decrease except for the small intestine, adipose and skin which demonstrated transient increases. Subcellular distribution in liver at 1 h showed radioactivity in all cell fractions. Although very lipophilic, (/sup 14/C)MBOCA was completely eliminated within 48 h with the major route via the feces (73.4%).

Methylene blue adsorption from glycerol solution onto the acicular ...

African Journals Online (AJOL)

The mechanism of methylene blue adsorption onto the surface of synthetic acicular habit of α-goethite from glycerol solution has been studied through batch experiment at 25, 30 and 35 0C in a glass cell of minimal dead volume. To describe the adsorption results, an attempt was made to fit the data to the Langmuir, ...

Single-unit pattern generators for quadruped locomotion

DEFF Research Database (Denmark)

Morse, Gregory; Risi, Sebastian; Snyder, Charles R

2013-01-01

Legged robots can potentially venture beyond the limits of wheeled vehicles. While creating controllers for such robots by hand is possible, evolutionary algorithms are an alternative that can reduce the burden of hand-crafting robotic controllers. Although major evolutionary approaches to legged...... on a new type of neuron called a single-unit pattern generator (SUPG). The SUPG, which is indirectly encoded by a compositional pattern producing network (CPPN) evolved by HyperNEAT, produces a flexible temporal activation pattern that can be reset and repeated at any time through an explicit trigger input...

Sulfonamide antibiotic removal and nitrogen recovery from synthetic urine by the combination of rotating advanced oxidation contactor and methylene urea synthesis process.

Science.gov (United States)

Fukahori, S; Fujiwara, T; Ito, R; Funamizu, N

2015-01-01

The combination of nitrogen recovery and pharmaceutical removal processes for livestock urine treatment were investigated to suppress the discharge of pollutants and recover nitrogen as resources. We combined methylene urea synthesis from urea and adsorption and photocatalytic decomposition of sulfonamide antibiotic using rotating advanced oxidation contactor (RAOC) contained for obtaining both safe fertilizer and reclaimed water. The methylene urea synthesis could recover urea in synthetic urine, however, almost all sulfonamide antibiotic was also incorporated, which is unfavorable from a safety aspect if the methylene urea is to be used as fertilizer. Conversely, RAOC could remove sulfonamide antibiotic without consuming urea. It was also confirmed that the methylene urea could be synthesized from synthetic urine treated by RAOC. Thus, we concluded that RAOC should be inserted prior to the nitrogen recovery process for effective treatment of urine and safe use of methylene urea as fertilizer.

Effect of some pre-treatments on the adsorption of methylene blue by Balkaya lignite

International Nuclear Information System (INIS)

Karaca, S.; Guerses, A.; Bayrak, R.

2004-01-01

In this study, the effects of some pre-treatments, such as HCl treatment, demineralization and pyrolysis, under a CO 2 atmosphere at different temperatures on the adsorption of methylene blue by Balkaya lignite were investigated. The adsorption capacities of the samples were determined before and after these pre-treatments. In addition, the removals of pyritic and organic sulfur and ash contents for the same coal samples were also defined. It was found that the adsorption capacities of the samples decreased after these pre-treatments. The decrease in adsorption capacity with pyrolysis can be attributed to the changes in surface morphology and/or pore size distribution of the coal samples. On the other hand, the observed decrease in adsorption capacity with removal of carbonates and silicates shows that these minerals have an important effect on methylene blue adsorption, and the adsorption considerably occurs through electrostatic interactions. In addition, the obtained results showed that the organic sulfur presence in the coal matrix have a positive effect on the methylene blue adsorption

Adsorption of methylene blue from aqueous solution on the surface ...

African Journals Online (AJOL)

Adsorption of dye methylene blue from aqueous solution on the surface of sheep wool and cotton fibers was accomplished under the optimize conditions of temperature, concentration, pH, stay time duration and quantity of adsorbent. Spectrometric technique was used for the measurements of concentration of dye before ...

X-ray quality increasing system controlled by single-chip microcomputer in single phase fluoroscopy unit

International Nuclear Information System (INIS)

Wang Qiaolin; Gu Hongmei

2004-01-01

Objective: To decrease the amount of radiation that doctor and patient receives by increasing X-ray quality. Methods: Using Single-chip Microcomputer technology, test and modulate AC(Alternating Current) from high voltage generator by IGBT. X-ray tube generates X-rays only at high energy area. Thus the amount of radiation decreases. Results: The tube current decreases remarkably and the amount of radiation that doctor and patient receives decreases effectively. Conclusion: the system can effectively decrease the amount of radiation and is widely applicable to the upgrade of all kinds of single phase X-ray units. (authors)

Methylene blue microbubbles as a model dual-modality contrast agent for ultrasound and activatable photoacoustic imaging

Science.gov (United States)

Jeon, Mansik; Song, Wentao; Huynh, Elizabeth; Kim, Jungho; Kim, Jeesu; Helfield, Brandon L.; Leung, Ben Y. C.; Goertz, David E.; Zheng, Gang; Oh, Jungtaek; Lovell, Jonathan F.; Kim, Chulhong

2014-01-01

Ultrasound and photoacoustic imaging are highly complementary modalities since both use ultrasonic detection for operation. Increasingly, photoacoustic and ultrasound have been integrated in terms of hardware instrumentation. To generate a broadly accessible dual-modality contrast agent, we generated microbubbles (a standard ultrasound contrast agent) in a solution of methylene blue (a standard photoacoustic dye). This MB2 solution was formed effectively and was optimized as a dual-modality contrast solution. As microbubble concentration increased (with methylene blue concentration constant), photoacoustic signal was attenuated in the MB2 solution. When methylene blue concentration increased (with microbubble concentration held constant), no ultrasonic interference was observed. Using an MB2 solution that strongly attenuated all photoacoustic signal, high powered ultrasound could be used to burst the microbubbles and dramatically enhance photoacoustic contrast (>800-fold increase), providing a new method for spatiotemporal control of photoacoustic signal generation.

Intrauterine Methylene Blue Injection Influences the Accuracy of Pulse Oximetry Readings

Directory of Open Access Journals (Sweden)

Fuh-Cheng Yeh

2005-12-01

Conclusions: Intraoperative administration of methylene blue may induce false low readings on pulse oximetry. The patient was not hypoxemic. If there is any doubt, arterial blood gas analysis should be done to ensure that the patient is well oxygenated.

Life-threatening intoxication with methylene bis(thiocyanate: clinical picture and pitfalls. A case report

Directory of Open Access Journals (Sweden)

Schnuelle Peter

2006-04-01

Full Text Available Abstract Background Methylene bis(thiocyanate (MBT is a microbiocidal agent mainly used in industrial water cooling systems and paper mills as an inhibitor of algae, fungi, and bacteria. Case presentation We describe the first case of severe intoxication following inhalation of powder in an industrial worker. Profound cyanosis and respiratory failure caused by severe methemoglobinemia developed within several minutes. Despite immediate admission to the intensive care unit, where mechanical ventilation and hemodialysis for toxin elimination were initiated, multi-organ failure involving liver, kidneys, and lungs developed. While liver failure was leading, the patient was successfully treated with the MARS (molecular adsorbent recirculating system procedure. Conclusion Intoxication with MBT is a potentially life-threatening intoxication causing severe methemoglobinemia and multi-organ failure. Extracorporeal liver albumin dialysis (MARS appears to be an effective treatment to allow recovery of hepatic function.

Photodynamic Therapy With Methylene Blue for Skin Ulcers Infected With Pseudomonas aeruginosa and Fusarium spp.

Science.gov (United States)

Aspiroz, C; Sevil, M; Toyas, C; Gilaberte, Y

Photodynamic therapy (PDT) is a therapeutic modality with significant antimicrobial activity. We present 2 cases of chronic lower limb ulcers in which fungal and bacterial superinfection complicated management. PDT with methylene blue as the photosensitizer led to clinical and microbiological cure with no significant adverse effects. PDT with methylene blue is a valid option for the management of superinfected chronic ulcers, reducing the use of antibiotics and the induction of resistance. Copyright © 2017 AEDV. Publicado por Elsevier España, S.L.U. All rights reserved.

Radioiodinated methylene blue for melanoma targeting: Chemical characterisation and tumour selectivity of labelled components

International Nuclear Information System (INIS)

Blower, Philip J.; Clark, Katherine; Link, Eva M.

1997-01-01

Radioiodinated methylene blue contains a mixture of components showing selective uptake in human pigmented melanoma, and it has potential for imaging and therapy. Nuclear magnetic resonance and mass spectroscopic studies show that the majority of the radioactivity (85%) is in the form of monoiodinated methylene blue, 4-iodo-3-methylamino-7-dimethylaminophenaza thionium chloride. The amino group ortho-to iodine has become demethylated to a mono-methylamino group. The remainder (15%) of the mixture is the doubly labelled 4,5-diiodo-3,7-bis(methylamino) phenazathionium chloride. The separated components show similar tumour selectivity in athymic mice bearing human pigmented melanomas

Removal of basic dye methylene blue by using bioabsorbents Ulva ...

African Journals Online (AJOL)

In the present study, the removal of textile dye methylene blue was studied by adsorption technique using adsorbents such as, alumina, Ulva lactuca and Sargassum (Maine algae). The batch technique was adopted under the optimize condition of amount of adsorbent, stay time, concentration, temperature and pH. By using ...

Use of Aspergillus wentii for biosorption of methylene blue from ...

African Journals Online (AJOL)

In this study, Aspergillus wentii was used as a biosorbent for the adsorption of methylene blue from aqueous solution. The effects of contact time, initial dye concentration, solution pH and temperature on biosorption were investigated. The contact time required (that is, the equilibrium time) for maximum dye biosorption was ...

Single unit approaches to human vision and memory.

Science.gov (United States)

Kreiman, Gabriel

2007-08-01

Research on the visual system focuses on using electrophysiology, pharmacology and other invasive tools in animal models. Non-invasive tools such as scalp electroencephalography and imaging allow examining humans but show a much lower spatial and/or temporal resolution. Under special clinical conditions, it is possible to monitor single-unit activity in humans when invasive procedures are required due to particular pathological conditions including epilepsy and Parkinson's disease. We review our knowledge about the visual system and visual memories in the human brain at the single neuron level. The properties of the human brain seem to be broadly compatible with the knowledge derived from animal models. The possibility of examining high-resolution brain activity in conscious human subjects allows investigators to ask novel questions that are challenging to address in animal models.

Derivation of an occupational exposure limit (OEL) for methylene chloride based on acute CNS effects and relative potency analysis.

Science.gov (United States)

Storm, J E; Rozman, K K

1998-06-01

The Occupational Safety and Health Administration (OSHA) methylene chloride Permissible Exposure Level (PEL) or 25 ppm is quantitatively derived from mouse tumor results observed in a high-exposure National Toxicology Program bioassay. Because this approach depends on controversial interspecies and low-dose extrapolations, the PEL itself has stimulated heated debate. Here, an alternative safety assessment for methylene chloride is presented. It is based on an acute human lowest-observed-adverse-effect level (LOAEL) of 200 ppm for subtle central nervous system (CNS) depression. Steep, parallel exposure-response curves for anesthetic and subanesthetic CNS effects associated with compounds mechanistically and structurally related to methylene chloride are shown to support a safety factor of two to account for inter-individual variability in response. LOAEL/no-observed-adverse-effect ratios for subtle CNS effects associated with structurally related solvents are shown to support a safety factor range of two to four to account for uncertainty in identifying a subthreshold exposure level. Anesthetic relative potencies and anesthetic/subanesthetic effect level ratios are shown to be constant for the compounds evaluated, demonstrating that subanesthetic relative potencies are also constant. Relative potencies among similarly derived occupational exposure limits (OELs) for solvents structurally related to methylene chloride are therefore used to validate the derived methylene chloride OEL range of 25-50 ppm. Because this safety assessment is based on human (rather than rodent) data and empirical (rather than theoretical) exposure-response relationships and is supported by relative potency analysis, it is a defensible alternative to to the OSHA risk assessment and should positively contribute to the debate regarding the appropriate basis and value for a methylene chloride PEL.

Alarm management in a single-patient room intensive care units

NARCIS (Netherlands)

van Pul, C.; Joshi, R.; Dijkman, W.; van de Mortel, H.; Mohns, T.; Andriessen, P.; Chen, Wei; Carlos Augusto, Juan; Seoane, Fernando; Lehocki, Fedor; Wolf, Klaus-Henderik; Arends, Johan; Ungureanu, Constantin; Wichert, Reiner

2015-01-01

An international trend in intensive care is the shift from open, bay area intensive care units towards single-patient room care, since this is considered optimal for patient healing and family privacy. However, in the intensive care setting, an increasing number of devices and parameters are being

Application of Spent Li-Ion Batteries Cathode in Methylene Blue Dye Discoloration

Directory of Open Access Journals (Sweden)

Eric M. Garcia

2017-01-01

Full Text Available This paper aims to present the mechanism study of methylene blue (MB discoloration using spent Li-ion battery cathode tape and hydrogen peroxide. The recycled cathode used in this work is composed of 72% of LiCoO2, 18% of carbon, and 10% of Al. The value found for surface area is 8.9 m2/g and the ZCP value occurs in pH = 2.95. Different from what is proposed in the literature, the most likely mechanism of methylene blue discoloration is the oxidation/delitiation of LiCoO2 and the reduction of H2O2 forming OH∙. Thus, in this paper, an important and promising alternative for discoloration of textile industry dyes using spent Li-ion battery cathode is presented.

Electronic Transport in Single Molecule Junctions: Control of the Molecule-Electrode Coupling Through Intramolecular Tunneling Barriers

DEFF Research Database (Denmark)

Danilov, Andrey; Kubatkin, Sergey; Kafanov, Sergey

2008-01-01

We report on single molecule electron transport measurements of two oligophenylenevinylene (OPV3) derivatives placed in a nanogap between gold (Au) or lead (Pb) electrodes in a field effect transistor device. Both derivatives contain thiol end groups that allow chemical binding to the electrodes....... One derivative has additional methylene groups separating the thiols from the delocalized -electron system. The insertion of methylene groups changes the open state conductance by 3-4 orders of magnitude and changes the transport mechanism from a coherent regime with finite zero-bias conductance...

Extraosseous uptake of 99sup(m)technetium methylene diphosphonate

International Nuclear Information System (INIS)

Sty, J.R.; Kun, L.; Casper, J.; Babbitt, D.P.

1980-01-01

A child with a ganglioneuroblastoma and tumor uptake of 99 sup(m)technetium methylene diphosphate ( 99 sup(m)Tc-MDP) is presented. After surgical removal of an encapsulated tumor and radiation therapy, an interval bone scan demonstrated the same presurgical abnormality. Awareness of abnormal uptake of 99 sup(m)Tc-MDP in irradiated renal tissue prevents interpreting radiation nephritis as recurrent tumor. (orig.) [de

Recruitment of single human low-threshold motor units with increasing loads at different muscle lengths.

Science.gov (United States)

McNulty, P A; Cresswell, A G

2004-06-01

We investigated the recruitment behaviour of low threshold motor units in flexor digitorum superficialis by altering two biomechanical constraints: the load against which the muscle worked and the initial muscle length. The load was increased using isotonic (low load), loaded dynamic (intermediate load) and isometric (high load) contractions in two studies. The initial muscle position reflected resting muscle length in series A, and a longer length with digit III fully extended in series B. Intramuscular EMG was recorded from 48 single motor units in 10 experiments on five healthy subjects, 21 units in series A and 27 in series B, while subjects performed ramp up, hold and ramp down contractions. Increasing the load on the muscle decreased the force, displacement and firing rate of single motor units at recruitment at shorter muscle lengths (Precruitment pattern was observed between loaded dynamic and isotonic contractions, but not between isometric and loaded dynamic contractions. Thus, the recruitment properties of single motor units in human flexor digitorum superficialis are sensitive to changes in both imposed external loads and the initial length of the muscle.

Methylene Blue-Loaded Dissolving Microneedles: Potential Use in Photodynamic Antimicrobial Chemotherapy of Infected Wounds

Directory of Open Access Journals (Sweden)

Ester Caffarel-Salvador

2015-09-01

Full Text Available Photodynamic therapy involves delivery of a photosensitising drug that is activated by light of a specific wavelength, resulting in generation of highly reactive radicals. This activated species can cause destruction of targeted cells. Application of this process for treatment of microbial infections has been termed “photodynamic antimicrobial chemotherapy” (PACT. In the treatment of chronic wounds, the delivery of photosensitising agents is often impeded by the presence of a thick hyperkeratotic/necrotic tissue layer, reducing their therapeutic efficacy. Microneedles (MNs are an emerging drug delivery technology that have been demonstrated to successfully penetrate the outer layers of the skin, whilst minimising damage to skin barrier function. Delivering photosensitising drugs using this platform has been demonstrated to have several advantages over conventional photodynamic therapy, such as, painless application, reduced erythema, enhanced cosmetic results and improved intradermal delivery. The aim of this study was to physically characterise dissolving MNs loaded with the photosensitising agent, methylene blue and assess their photodynamic antimicrobial activity. Dissolving MNs were fabricated from aqueous blends of Gantrez® AN-139 co-polymer containing varying loadings of methylene blue. A height reduction of 29.8% was observed for MNs prepared from blends containing 0.5% w/w methylene blue following application of a total force of 70.56 N/array. A previously validated insertion test was used to assess the effect of drug loading on MN insertion into a wound model. Staphylococcus aureus, Escherichia coli and Candida albicans biofilms were incubated with various methylene blue concentrations within the range delivered by MNs in vitro (0.1–2.5 mg/mL and either irradiated at 635 nm using a Paterson Lamp or subjected to a dark period. Microbial susceptibility to PACT was determined by assessing the total viable count. Kill rates of >96

Citrus pectin derived porous carbons as a superior adsorbent toward removal of methylene blue

International Nuclear Information System (INIS)

Zhang, Wenlin; Zhang, Lian Ying; Zhao, Xi Juan; Zhou, Zhiqin

2016-01-01

An adsorbent, citrus pectin derived porous carbons with ultra-high adsorption capacity, rapid adsorption rate and good reusability toward removal of methylene blue, was synthesized by a facile zinc chloride activation approach in this study. The materials hold a great potential for treatment of dye wastewater. - Graphical abstract: Citrus pectin derived porous carbons with ultra-high adsorption capacity, rapid adsorption rate and good reusability toward methylene blue removal. - Highlights: • Citrus pectin derived porous carbons (CPPCs) were synthesized a facile zinc chloride activation approach. • CPPCs had abundant macro/meso/micropores for trapping MB molecules. • CPPCs exhibited ultrahigh adsorption capacity, rapid adsorption rate and good reusability toward removal of MB.

Citrus pectin derived porous carbons as a superior adsorbent toward removal of methylene blue

Energy Technology Data Exchange (ETDEWEB)

Zhang, Wenlin [College of Horticulture and landscape Architecture, Southwest University, Chongqing 400716 (China); Zhang, Lian Ying [Institute for Clean Energy & Advanced Materials, Southwest University, Chongqing 400715 (China); Zhao, Xi Juan [College of Horticulture and landscape Architecture, Southwest University, Chongqing 400716 (China); Key Laboratory of Horticulture Science for Southern Mountainous Regions, Ministry of Education, Chongqing 400715 (China); Zhou, Zhiqin, E-mail: zhouzhiqin@swu.edu.cn [College of Horticulture and landscape Architecture, Southwest University, Chongqing 400716 (China); Key Laboratory of Horticulture Science for Southern Mountainous Regions, Ministry of Education, Chongqing 400715 (China)

2016-11-15

An adsorbent, citrus pectin derived porous carbons with ultra-high adsorption capacity, rapid adsorption rate and good reusability toward removal of methylene blue, was synthesized by a facile zinc chloride activation approach in this study. The materials hold a great potential for treatment of dye wastewater. - Graphical abstract: Citrus pectin derived porous carbons with ultra-high adsorption capacity, rapid adsorption rate and good reusability toward methylene blue removal. - Highlights: • Citrus pectin derived porous carbons (CPPCs) were synthesized a facile zinc chloride activation approach. • CPPCs had abundant macro/meso/micropores for trapping MB molecules. • CPPCs exhibited ultrahigh adsorption capacity, rapid adsorption rate and good reusability toward removal of MB.

Methylene blue protects against TDP-43 and FUS neuronal toxicity in C. elegans and D. rerio.

Directory of Open Access Journals (Sweden)

Alexandra Vaccaro

Full Text Available The DNA/RNA-binding proteins TDP-43 and FUS are found in protein aggregates in a growing number of neurodegenerative diseases, including amyotrophic lateral sclerosis (ALS and related dementia, but little is known about the neurotoxic mechanisms. We have generated Caenorhabditis elegans and zebrafish animal models expressing mutant human TDP-43 (A315T or G348C or FUS (S57Δ or R521H that reflect certain aspects of ALS including motor neuron degeneration, axonal deficits, and progressive paralysis. To explore the potential of our humanized transgenic C. elegans and zebrafish in identifying chemical suppressors of mutant TDP-43 and FUS neuronal toxicity, we tested three compounds with potential neuroprotective properties: lithium chloride, methylene blue and riluzole. We identified methylene blue as a potent suppressor of TDP-43 and FUS toxicity in both our models. Our results indicate that methylene blue can rescue toxic phenotypes associated with mutant TDP-43 and FUS including neuronal dysfunction and oxidative stress.

Methylene blue protects against TDP-43 and FUS neuronal toxicity in C. elegans and D. rerio.

Science.gov (United States)

Vaccaro, Alexandra; Patten, Shunmoogum A; Ciura, Sorana; Maios, Claudia; Therrien, Martine; Drapeau, Pierre; Kabashi, Edor; Parker, J Alex

2012-01-01

The DNA/RNA-binding proteins TDP-43 and FUS are found in protein aggregates in a growing number of neurodegenerative diseases, including amyotrophic lateral sclerosis (ALS) and related dementia, but little is known about the neurotoxic mechanisms. We have generated Caenorhabditis elegans and zebrafish animal models expressing mutant human TDP-43 (A315T or G348C) or FUS (S57Δ or R521H) that reflect certain aspects of ALS including motor neuron degeneration, axonal deficits, and progressive paralysis. To explore the potential of our humanized transgenic C. elegans and zebrafish in identifying chemical suppressors of mutant TDP-43 and FUS neuronal toxicity, we tested three compounds with potential neuroprotective properties: lithium chloride, methylene blue and riluzole. We identified methylene blue as a potent suppressor of TDP-43 and FUS toxicity in both our models. Our results indicate that methylene blue can rescue toxic phenotypes associated with mutant TDP-43 and FUS including neuronal dysfunction and oxidative stress.

Extended Fenske-Hall LCAO MO Calculations for Mixed Methylene Dihalides

Science.gov (United States)

Ziemann, Hartmut; Paulun, Manfred

1988-10-01

The electronic structure of mixed methylene dihalides CH2XY (X, Y = F, Cl, Br. I) has been studied using extended Fenske-Hall LCAO MO method. The comparison with available photoelec­tron spectra confirmes previous assignments of all bands with binding energies <100 eV. The electronic structure changes occurring upon varying the halogen substituents are discussed.

Effective photocatalytic decolorization of methylene blue utilizing ZnO/rectorite nanocomposite under simulated solar irradiation

Energy Technology Data Exchange (ETDEWEB)

Li, Shi-qian, E-mail: shiqianli04@tom.com [College of Resource and Environmental Science, Wuhan University, Hubei Key Laboratory of Biomass-resource Chemical and Environment Bio-technology, Wuhan 430079 (China); Department of Biology and Chemical Engineering, FuQing Branch of Fujian Normal University, Fuqing 350300 (China); Zhou, Pei-jiang; Zhang, Wan-shun [College of Resource and Environmental Science, Wuhan University, Hubei Key Laboratory of Biomass-resource Chemical and Environment Bio-technology, Wuhan 430079 (China); Chen, Sheng [Department of Biology and Chemical Engineering, FuQing Branch of Fujian Normal University, Fuqing 350300 (China); Peng, Hong [State Key Laboratory of Water Resources and Hydropower Engineering Science, Wuhan University, Hubei, Wuhan 430072 (China)

2014-12-15

Highlights: • Preparation of ZnO inserted in rectorite as photocatalyst in methylene blue photodegradation. • The ZnO/rectorite can be used as adsorbents and photocatalysts. • The ZnO/rectorite system was easy to be gathered and recycled. • Inferred ZnO/rectorite the photocatalytic degradation methylene blue of aqueous micro mechanism. - Abstract: Preparation of a nanometer zinc oxide/rectorite (ZnO/REC) composites photocatalyst based on natural rectorite was conducted using a hydrothermal intercalation method. The structure, thermal property, and surface morphology of ZnO/REC were characterized by X-ray diffractor (XRD), thermogravimetric analysis (TGA), high-resolution transmission electron microscope (HRTEM) and scanning electron microscope (SEM) techniques. The photocatalytic activity of ZnO/REC was evaluated by photocatalytic decolorization of methylene blue (MB) in aqueous solution as a model pollutant under simulated sunlight irradiation. The HRTEM results revealed that well-dispersed and uniform ZnO/REC nanocomposites with diameters of 10 nm were embedded in rectorite. The ZnO/REC nanocomposite exhibited high photocatalytic activity under simulated solar irradiation. After 2 h of irradiation by simulated solar light, over 99% of methylene blue solution (15 mg/L) was decolorized with 0.9 g/L of the photocatalyst. The ZnO/REC was reusable, which meant that the adsorption photocatalytic decolorization process could be operated at a relatively low cost. Since this process does not require the addition of hydrogen peroxide but uses sunlight, it can be developed as an economically feasible and environmentally friendly method to decolorize or treat dye wastewater using solar.

Tracking Single Units in Chronic, Large Scale, Neural Recordings for Brain Machine Interface Applications

Directory of Open Access Journals (Sweden)

Ahmed eEleryan

2014-07-01

Full Text Available In the study of population coding in neurobiological systems, tracking unit identity may be critical to assess possible changes in the coding properties of neuronal constituents over prolonged periods of time. Ensuring unit stability is even more critical for reliable neural decoding of motor variables in intra-cortically controlled brain-machine interfaces (BMIs. Variability in intrinsic spike patterns, tuning characteristics, and single-unit identity over chronic use is a major challenge to maintaining this stability, requiring frequent daily calibration of neural decoders in BMI sessions by an experienced human operator. Here, we report on a unit-stability tracking algorithm that efficiently and autonomously identifies putative single-units that are stable across many sessions using a relatively short duration recording interval at the start of each session. The algorithm first builds a database of features extracted from units' average spike waveforms and firing patterns across many days of recording. It then uses these features to decide whether spike occurrences on the same channel on one day belong to the same unit recorded on another day or not. We assessed the overall performance of the algorithm for different choices of features and classifiers trained using human expert judgment, and quantified it as a function of accuracy and execution time. Overall, we found a trade-off between accuracy and execution time with increasing data volumes from chronically implanted rhesus macaques, with an average of 12 seconds processing time per channel at ~90% classification accuracy. Furthermore, 77% of the resulting putative single-units matched those tracked by human experts. These results demonstrate that over the span of a few months of recordings, automated unit tracking can be performed with high accuracy and used to streamline the calibration phase during BMI sessions.

Supramolecular Recognition Allows Remote, Site-Selective C-H Oxidation of Methylenic Sites in Linear Amines.

Science.gov (United States)

Olivo, Giorgio; Farinelli, Giulio; Barbieri, Alessia; Lanzalunga, Osvaldo; Di Stefano, Stefano; Costas, Miquel

2017-12-18

Site-selective C-H functionalization of aliphatic alkyl chains is a longstanding challenge in oxidation catalysis, given the comparable relative reactivity of the different methylenes. A supramolecular, bioinspired approach is described to address this challenge. A Mn complex able to catalyze C(sp 3 )-H hydroxylation with H 2 O 2 is equipped with 18-benzocrown-6 ether receptors that bind ammonium substrates via hydrogen bonding. Reversible pre-association of protonated primary aliphatic amines with the crown ether selectively exposes remote positions (C8 and C9) to the oxidizing unit, resulting in a site-selective oxidation. Remarkably, such control of selectivity retains its efficiency for a whole series of linear amines, overriding the intrinsic reactivity of C-H bonds, no matter the chain length. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Redox reactions of methylene blue: a pulse radiolysis study

International Nuclear Information System (INIS)

Kishore, K.; Guha, S.N.; Mahadevan, J.; Moorthy, P.N.; Mittal, J.P.

1989-01-01

One-electron oxidation of methylene blue (MB - has been studied using specific oxidizing radicals such as Cl 2 - , Br 2 - , N 3 and Tl(II) in acidic and neutral aqueous solutions). The transient spectrum showed absorption maxima at 525 nm and 360 nm in the acidic pH region. At neutral pH also the absorption maxima were at 525 and 360 nm but the extinction coefficients were lower by 30%. A pK a of ∼4.3 was observed for the equilibrium MBH 3+ MB 2+ + H + . In the case of N 3 radical as the oxidant, the equilibrium: N 3 + MB = N 3 - + MB 2+ was observed for which an equilibrium constant of 120 was estimated from the experimental data. From this as well as from cyclic voltammetric experiments, the redox potential for the MB 2+ /MB + couple was calculated as 1.25 V vs NHE. The transient species produced by the reaction of OH radicals with methylene blue gave a very different spectrum with λ m = 400nm and a pK a of ∼ 8.6, and hence it is inferred that OH radicals do not bring about one-electron oxidation of the molecule. (author)

Nanoengineering of methylene blue loaded silica encapsulated magnetite nanospheres and nanocapsules for photodynamic therapy

Energy Technology Data Exchange (ETDEWEB)

Andhariya, Nidhi [Bhavnagar University, Department of Physics (India); Chudasama, Bhupendra, E-mail: bnchudasama@gmail.com [Thapar University, School of Physics and Materials Science (India); Mehta, R. V. [Bhavnagar University, Department of Physics (India); Upadhyay, R. V. [Charotar University of Science and Technology, P.D. Patel Institute of Applied Sciences (India)

2011-09-15

Core-shell nanostructures have emerged as an important class of functional materials with potential applications in diverse fields, especially in health sciences. In this article, nanoengineering of novel magnetic colloidal dispersion containing surface modifiable silica with a core of single domain magnetite nanoparticles loaded with photosensitizer (PS) drug 'Methylene blue' (MB) has been described. Magnetite core is produced by the well-established chemical coprecipitation technique and silica shell is formed over it by the modified hydrolysis and condensation of TEOS (tetraethyl orthosilicate). Conditions for reaction kinetics have been established to tailor the core-shell structures in the form of nanospheres and nanocapsules. MB is loaded into the nanostructures by demethylation reaction. The major conclusion drawn from this study is that the synthesis route yields stable, non-aggregated MB loaded superparamagnetic magnetite-silica nanostructures with tailored morphology, tunable loading, and excellent magnetic properties.

Estimation of surface area and pore volume of activated carbons by methylene blue and iodine numbers

Directory of Open Access Journals (Sweden)

Cleiton A. Nunes

2011-01-01

Full Text Available Data of methylene blue number and iodine number of activated carbons samples were calibrated against the respective surface area, micropore volume and total pore volume using multiple regression. The models obtained from the calibrations were used in predicting these physical properties of a test group of activated carbon samples produced from several raw materials. In all cases, the predicted values were in good agreement with the expected values. The method allows extracting more information from the methylene blue and iodine adsorption studies than normally obtained with this type of material.

Calixarene methylene bisphosphonic acids as promising effectors of biochemical processes

Directory of Open Access Journals (Sweden)

S. V. Komisarenko

2013-12-01

Full Text Available This interdisciplinary study, performed with participation of research workers of Palladin Institute of Biochemistry and Institute of Organic Chemist­ry of NAS of Ukraine, is devoted to analysis of biochemical effects of some calixarene methylene bisphosphonic acids (cyclic phenol oligomers on two well-known biological phenomenons – Mg2+-dependent ATP hydrolysis (myosin subfragment-1 of myometrium smooth muscle was used as an example and fibrin polymerization. Calix[4]arene С-97 (calix[4]arene methylene bisphosphonic acids is a macrocyclic substance, which contains intramolecular highly ordered lipophilic cavity formed by four aromatic rings, one of which is functionalized at the upper rim with methylene bisphosphonic group. At concentration of 100 µM, this substance was shown to effectively inhibit ATPase activity of pig myometrium myosin subfragment-1 (inhibition coefficient І0.5 = 83 ± 7 µM. At the same time, this calix[4]arene causes significant (vs. control increase of myosin subfragment-1 hydrodynamic diameter, which may indicate formation of an intermolecular complex between calixa­rene and myosin head. Computer simulation methods (docking and molecular dynamics with addition of grid technologies enabled to elucidate the grounds of intermolecular interactions between calix[4]arene С-97 and myometrium myosin subfragment-1, that involve hydrophobic, electrostatic and π-π-stacking interactions, some of which are close to the ATPase active centre. In view of the ability of calixarenes to penetrate into the cell and their low toxicity, the results obtained may be used as a basis for further development of a new generation of supramolecular effectors (starting from the above mentioned substances, in particular calix[4]arene С-97 for regulation of smooth muscle contractile activity at the level of ATP dependent actin-myosin interaction. Calix[4]arenes bearing two or four methylenebisphosphonic acid groups at the macrocyclic upper

Breakdown of methylene blue and methyl orange by pulsed corona discharge

NARCIS (Netherlands)

Grabowski, L.R.; Veldhuizen, van E.M.; Pemen, A.J.M.; Rutgers, W.R.

2007-01-01

The recently developed corona above water technique is applied to water containing 10 mg l-1 methylene blue (MB) or methyl orange (MO). The corona discharge pulses are created with a spark gap switched capacitor followed by a transmission line transformer. The pulse amplitude is 40 kV; its duration

Products of the reaction between methylene iodide and tertiary arsines

International Nuclear Information System (INIS)

Gigauri, R.D.; Arabuli, L.G.; Machaidze, Z.I.; Rusiya, M.Sh.

2005-01-01

Iodides of iodomethylenetrialkyl(aryl) arsonium were synthesized with high yields as a result of interaction between methylene iodide and tertiary arsines. Exchange reactions of the iodides prepared with lead(II) nitrate in water-alcohol solutions gave rise to formation of iodomethylenetrialkyl(aryl) arsonium nitrates. All the products prepared were characterized by data of elementary analysis, IR spectroscopy, conductometry and melting points measurements [ru

Source reduction for prevention of methylene chloride hazards: cases from four industrial sectors

Directory of Open Access Journals (Sweden)

Ellenbecker Michael J

2003-07-01

Full Text Available Abstract Background Source reduction, defined as chemical, equipment and process changes that intervene in an industrial process to eliminate or reduce hazards, has not figured as a front-line strategy for the protection of workers' health. Such initiatives are popular for environmental protection, but their feasibility and effectiveness as an industrial hygiene approach have not been well described. Methods We investigated four cases of source reduction as a hazard prevention strategy in Massachusetts companies that had used methylene chloride, an occupational carcinogen, for cleaning and adhesive thinning. Three cases were retrospective and one was prospective, where the researchers assisted with the source reduction process change. Data were collected using qualitative research methods, including in-depth interviews and site visits. Results Motivated by environmental restrictions, a new worker health standard, and opportunity for productivity improvements, three companies eliminated their use of methylene chloride by utilizing available technologies and drop-in substitutes. Aided by technical assistance from the investigators, a fourth case dramatically reduced its use of methylene chloride via process and chemistry changes. While the companies' evaluations of potential work environment impacts of substitutes were not extensive, and in two cases new potential hazards were introduced, the overall impact of the source reduction strategy was deemed beneficial, both from a worker health and a production standpoint. Conclusion The findings from these four cases suggest that source reduction should be considered potentially feasible and effective for reducing or eliminating the potential hazards of methylene chloride exposure. Especially when faced with a hazard that is both an environmental and worker health concern, companies may chose to change their processes rather than rely on local exhaust ventilation equipment or personal protective

Preparation of Carbon-Chitosan-Polyvinyl Chloride (CC-PVC) Material and its Application to Electrochemical Degradation of Methylene Blue in Sodium Chloride Solution

Science.gov (United States)

Riyanto; Prawidha, A. D.

2018-01-01

Electrochemical degradation of methylene blue using Carbon-Chitosan-Polyvinyl Chloride (CC-PVC) electrode in sodium chloride have been done. The aim of this work was to degradation of methylene blue using Carbon-Chitosan-Polyvinyl Chloride (CC-PVC). Carbon chitosan composite electrode was preparing by Carbon and Chitosan powder and PVC in 4 mL tetrahydrofuran (THF) solvent and swirled flatly to homogeneous followed by drying in an oven at 100 °C for 3 h. The mixture was placed in stainless steel mould and pressed at 10 ton/cm2. Sodium chloride was used electrolyte solution. The effects of the current and electrolysis time were investigated using spectrophotometer UV-Visible. The experimental results showed that the carbon-chitosan composite electrode have higher effect in the electrochemical degradation of methylene blue in sodium chloride. Based on UV-visible spectra analysis shows current and electrolysis time has high effect to degradation of methylene blue in sodium chloride. Chitosan and polyvinyl chloride can strengthen the bond between the carbons so that the material has the high stability and conductivity. As conclusions is Carbon-Chitosan-Polyvinyl Chloride (CC-PVC) electrode have a high electrochemical activity for degradation of methylene blue in sodium chloride.

Functional elastic hydrogel as recyclable membrane for the adsorption and degradation of methylene blue.

Directory of Open Access Journals (Sweden)

Song Bao

Full Text Available Developing the application of high-strength hydrogels has gained much attention in the fields of medical, pharmacy, and pollutant removal due to their versatility and stimulus-responsive properties. In this presentation, a high-strength freestanding elastic hydrogel membrane was constructed by clay nanosheets, N, N-dimethylacrylamide and 2-acrylamide-2-methylpropanesulfonic acid for adsorption of methylene blue and heavy metal ions. The maximum values of elongation and Young's modulus for 0.5% AMPSNa hydrogel were 1901% and 949.4 kPa, respectively, much higher than those of traditional hydrogels. The adsorptions were confirmed to follow pseudo-second kinetic equation and Langmuir isotherm model fits the data well. The maximum adsorption capacity of hydrogel towards methylene blue was 434.8 mg g(-1. The hydrogel also exhibited higher separation selectivity to Pb(2+ than Cu(2+. The methylene blue adsorbed onto the hydrogel membrane can be photocatalytically degraded by Fenton agent and the hydrogel membrane could be recycled at least five times without obvious loss in mechanical properties. In conclusion, this presentation demonstrates a convenient strategy to prepare tough and elastic clay nanocomposite hydrogel, which can not only be applied as recyclable membrane for the photocatalytic degradation of organic dye, but also for the recovery of valuables.

Nurses' Perceptions of Pediatric Intensive Care Unit Environment and Work Experience After Transition to Single-Patient Rooms.

Science.gov (United States)

Kudchadkar, Sapna R; Beers, M Claire; Ascenzi, Judith A; Jastaniah, Ebaa; Punjabi, Naresh M

2016-09-01

The architectural design of the pediatric intensive care unit may play a major role in optimizing the environment to promote patients' sleep while improving stress levels and the work experience of critical care nurses. To examine changes in nurses' perceptions of the environment of a pediatric critical care unit for promotion of patients' sleep and the nurses' work experience after a transition from multipatient rooms to single-patient rooms. A cross-sectional survey of nurses was conducted before and after the move to a new hospital building in which all rooms in the pediatric critical care unit were single-patient rooms. Nurses reported that compared with multipatient rooms, single-patient private rooms were more conducive to patients sleeping well at night and promoted a more normal sleep-wake cycle (P noise in single-patient rooms (33%) than in multipatient rooms (79%; P pediatric intensive care unit environment for promoting patients' sleep and the nurses' own work experience. ©2016 American Association of Critical-Care Nurses.

Nuclear overhauser spectroscopy of chiral CHD methylene groups

Energy Technology Data Exchange (ETDEWEB)

Augustyniak, Rafal [Ecole Normale Supérieure – PSL Research University, Département de chimie (France); Stanek, Jan [University of Warsaw, Faculty of Chemistry (Poland); Colaux, Henri; Bodenhausen, Geoffrey [Ecole Normale Supérieure – PSL Research University, Département de chimie (France); Koźmiński, Wiktor [University of Warsaw, Faculty of Chemistry (Poland); Herrmann, Torsten [Université de Lyon/UMR 5280 CNRS/ENS Lyon/UCB Lyon 1, Institut des Sciences Analytiques, Centre de RMN à Très Hauts Champs (France); Ferrage, Fabien, E-mail: Fabien.Ferrage@ens.fr [Ecole Normale Supérieure – PSL Research University, Département de chimie (France)

2016-01-15

Nuclear magnetic resonance spectroscopy (NMR) can provide a great deal of information about structure and dynamics of biomolecules. The quality of an NMR structure strongly depends on the number of experimental observables and on their accurate conversion into geometric restraints. When distance restraints are derived from nuclear Overhauser effect spectroscopy (NOESY), stereo-specific assignments of prochiral atoms can contribute significantly to the accuracy of NMR structures of proteins and nucleic acids. Here we introduce a series of NOESY-based pulse sequences that can assist in the assignment of chiral CHD methylene protons in random fractionally deuterated proteins. Partial deuteration suppresses spin-diffusion between the two protons of CH{sub 2} groups that normally impedes the distinction of cross-relaxation networks for these two protons in NOESY spectra. Three and four-dimensional spectra allow one to distinguish cross-relaxation pathways involving either of the two methylene protons so that one can obtain stereospecific assignments. In addition, the analysis provides a large number of stereospecific distance restraints. Non-uniform sampling was used to ensure optimal signal resolution in 4D spectra and reduce ambiguities of the assignments. Automatic assignment procedures were modified for efficient and accurate stereospecific assignments during automated structure calculations based on 3D spectra. The protocol was applied to calcium-loaded calbindin D{sub 9k}. A large number of stereospecific assignments lead to a significant improvement of the accuracy of the structure.

Synergistic effect of pulsed corona discharges and ozonation on decolourization of methylene blue in water

CERN Document Server

Malik, M A; Ghaffar, A; Ahmed, K

2002-01-01

The effect of O sub 2 and O sub 3 bubbling on decolourization of methylene blue by pulsed corona discharges in water was studied. The pulsed corona discharges were produced by charging an 80 pF capacitor with a 40 kV DC source, through a 100 M OMEGA resistor, and discharging it into a needle-plate type reactor at 60 Hz through a rotating spark gap switch. A 20 ml sample of 13.25 mg l sup - sup 1 methylene blue in distilled water was decolourized in 120 min. Bubbling O sub 2 at 10 ml min sup - sup 1 through the discharge region reduced the decolourization time to 25 min. Bubbling O sub 2 containing 1500 mu mol O sub 3 l sup - sup 1 at 10 ml min sup - sup 1 reduced the decolourization time to 8 min. The O sub 3 was produced by fractionating input energy between a water treatment reactor and a O sub 3 generator, i.e. no additional energy was consumed for O sub 3 production. Under the same experimental conditions methylene blue solution in tap water was decolourized in >210 min by corona discharge in solution, in...

Conformational analysis of the chemical shifts for molecules containing diastereotopic methylene protons

Science.gov (United States)

Borowski, Piotr

2012-01-01

Quantum chemistry SCF/GIAO calculations were carried out on a set of compounds containing diastereotopic protons. Five molecules, including recently synthesized 1,3-di(2,3-epoxypropoxy)benzene, containing the chiral or pro-chiral center and the neighboring methylene group, were chosen. The rotational averages (i.e. normalized averages with respect to the rotation about the torsional angle τ with the exponential energy weight at temperature T) calculated individually for each of the methylene protons in 1,3-di(2,3-epoxypropoxy)benzene differ by ca. 0.6 ppm, which is significantly less than the value calculated for the lowest energy conformer. This value turned out to be low enough to guarantee the proper ordering of theoretical chemical shifts, supporting the interpretation of the 1H NMR spectrum of this important compound. The rotational averages of chemical shifts for methylene protons for a given type of conformer are shown to be essentially equal to the Boltzmann averages (here, the population-weighted averages for the individual conformers representing minima on the E( τ) cross-section). The calculated Boltzmann averages in the representative conformational space may exhibit completely different ordering as compared to the chemical shifts calculated for the lowest-energy conformer. This is especially true in the case of molecules, for which no significant steric effects are present. In this case, only Boltzmann averages account for the experimental pattern of proton signals. In addition, better overall agreement with experiment (lower value of the root-mean-square deviation between calculated and measured chemical shifts) is typically obtained when Boltzmann averages are used.

Comparing toxicologic and epidemiologic studies: methylene chloride--a case study.

Science.gov (United States)

Stayner, L T; Bailer, A J

1993-12-01

Exposure to methylene chloride induces lung and liver cancers in mice. The mouse bioassay data have been used as the basis for several cancer risk assessments. The results from epidemiologic studies of workers exposed to methylene chloride have been mixed with respect to demonstrating an increased cancer risk. The results from a negative epidemiologic study of Kodak workers have been used by two groups of investigators to test the predictions from the EPA risk assessment models. These two groups used very different approaches to this problem, which resulted in opposite conclusions regarding the consistency between the animal model predictions and the Kodak study results. The results from the Kodak study are used to test the predictions from OSHA's multistage models of liver and lung cancer risk. Confidence intervals for the standardized mortality ratios (SMRs) from the Kodak study are compared with the predicted confidence intervals derived from OSHA's risk assessment models. Adjustments for the "healthy worker effect," differences in length of follow-up, and dosimetry between animals and humans were incorporated into these comparisons. Based on these comparisons, we conclude that the negative results from the Kodak study are not inconsistent with the predictions from OSHA's risk assessment model.

Methylene-Cycloalkylacetate (MCA) Scaffold-Based Compounds as Novel Neurotropic Agents.

Science.gov (United States)

Lankri, David; Haham, Dikla; Lahiani, Adi; Lazarovici, Philip; Tsvelikhovsky, Dmitry

2018-04-18

One of the main symptoms in degenerative diseases is death of neuronal cell followed by the loss of neuronal pathways. In neuronal cultures, neurite outgrowths are cell sprouts capable of transforming into either axons or dendrites, to further form functional neuronal synaptic connections. Such connections have an important role in brain cognition, neuronal plasticity, neuronal survival, and regeneration. Therefore, drugs that stimulate neurite outgrowth may be found beneficial in ameliorating neural degeneration. Here, we establish the existence of a unique family of methylene-cycloalkylacetate-based molecules (MCAs) that interface with neuronal cell properties and operate as acceptable pharmacophores for a novel neurotropic (neurite outgrowth inducing) lead compounds. Using an established PC12 cell bioassay, we investigated the neurotropic effect of methylene-cycloalkylacetate compounds by comparison to NGF, a known neurotropic factor. Micrographs of the cells were collected by using a light microscope camera, and digitized photographs were analyzed for compound-induced neurotropic activity using an NIH image protocol. The results indicate that the alkene element, integrated within the cycloalkylacetate core, is indispensable for neurotropic activity. The discovered lead compounds need further mechanistic investigation and may be improved toward development of a neurotropic drug.

Methylene blue adsorption in clay mineral dealt with organic cation

International Nuclear Information System (INIS)

Silva, T.L.; Lemos, V.P.

2011-01-01

The interaction among organic cations, as the methylene blue (AM) and benzyltrimethylammonium (BTMA), and clay minerals of the group of the smectite they result in the formation of applied materials in the adsorption of organic pollutant presents in waters, soils and you cultivate. In this work they were prepared the adsorbents (organic-clays) smectite - AM and smectite-BTMA. The precursory sample of smectite was collected in Rio Branco-Acre. We were also used an smectite sample collected in Sena Madureira (SM)-Acre already characterized in previous work and a sample of standard smectite Swy-2-Na-Montmorillonite (SWy-2) of Wymong - USA. The organic agents selected for this study they were: Blue of Methylene, denominated AM and Benzyltrimethylammonium, denominated BTMA. They were appraised the capacities adsorptive of the treated samples with BTMA being used AM as adsorbate. The results of these evaluations detected that ran total adsorption of AM (concentrations varying from 1 to 10 ppm) for the treated samples with BTMA. The organic cation, BTMA, interacting with the surfaces of the natural clay was more efficient in the adsorption of AM than the clay without the previous treatment with this salt. (author)

SERS-active Ag, Au and Ag–Au alloy nanoparticles obtained by laser ablation in liquids for sensing methylene blue

Energy Technology Data Exchange (ETDEWEB)

Olea-Mejía, Oscar, E-mail: oleaoscar@yahoo.com.mx [Centro Conjunto de Investigación en Química Sustentable UAEM-UNAM, Universidad Autónoma del Estado de México, km 14.5 Carretera Toluca-Atlacomulco, San Cayetano 50200, México (Mexico); Fernández-Mondragón, Mariana; Rodríguez-de la Concha, Gabriela [Centro Conjunto de Investigación en Química Sustentable UAEM-UNAM, Universidad Autónoma del Estado de México, km 14.5 Carretera Toluca-Atlacomulco, San Cayetano 50200, México (Mexico); Camacho-López, Marco [Laboratorio de Investigación y Desarrollo de Materiales Avanzados, Universidad Autónoma del Estado de México, Km 14.5 Carretera Toluca-Atlacomulco, San Cayetano 50925, México (Mexico)

2015-09-01

Highlights: • We synthesized Ag/Au nanoparticles by laser ablation in liquids. • We characterized such particles by UV–vis, TEM and EDS/STEM. • The SERS effect was studied for the obtained nanoparticles. • Pure silver nanoparticles showed the highest SERS signals. • We can sense methylene blue at a concentration of 10{sup −10} mole/L. - Abstract: We have synthesized Ag–Au nanoparticles by laser ablation in liquids using five different targets: 100% Ag, 80%Ag/20%Au, 50%Ag/50%Au, 20%Ag/80%Au and 100% Au (weight percentages). We used ethanol and methylene blue solutions in ethanol as the liquid media. The nanoparticles were mostly spherical with diameters 15, 19, 18, 23 and 11 nm, respectively. When alloyed targets were used, the resulting nanoparticles were completely alloyed forming solid solutions as evidenced by UV–vis Spectroscopy and Scanning Transmission Electron Microscopy. The obtained nanoparticles were employed to study the SERS effect of the methylene blue molecule. All the samples showed good SERS activity, however the ones composed of pure silver showed the greatest Raman signal enhancement. Finally, pure Ag nanoparticles were used for sensing methylene blue at different concentrations. While almost no signal can be discerned from the Raman spectrum when no particles are used at a concentration of methylene blue of 1 × 10{sup −2} M (∼3000 ppm), when Ag nanoparticles are used one can observe the characteristic peak of the molecule at concentrations as low as 1 × 10{sup −10} M (∼3 × 10{sup −5} ppm)

Cytologic and radiosensibilizer action of the methylene blue

International Nuclear Information System (INIS)

Teixeira, P.C.N.

1989-01-01

This work was designed with the aim of studying the use of Methylene Blue as a possible cellular sensitizer to heat and X-rays effects. We were able to show that MB can sensitize bacteria to these two agents. This sensitization is dependent on factors that can interfere with the penetration of the dye through the cellular membrane, like temperature, concentration and permeability. On the other hand, the sensitization is dependent on repair systems. In this work, we show that damages induced by heat and MB are repaired chiefly by the excision repair system, since mutants deficient in UVR ABC endonuclease or in DNA polimerase I are very sensitive to this treatment. This was confirmed by measuring the excision of sup(3)H labeled thymidine from the DNA after treatment of bacteria with heat and MB. Repair of damage produced by X-rays depends on the DNA polimerase I enzyme. It seems that MB can interfere with this enzyme inhibiting the repair of X-rays produced lesions. It is shown too that MB alone, in alkaline conditions, can induce single-strand-breaks in DNA. This means that in the cells, MB probably induces alkali labilizations that become SSB in alkaline conditions. Since X rays are used in cancer therapy, and MB penetrates preferably in malignant cells, our aim was to determine the possibility of using these two agents to improve the discrimination of the lethal effects of X-rays between malignant and normal cells. (author)

Capillary gas chromatography of alkylbenzenes II. Correlations between the structures and methylene group increments and differences in retention indices of isomers

NARCIS (Netherlands)

Sojak, L.; Janak, J.; Rijks, J.A.

1977-01-01

The contribution to gas chromatographic retention behaviour of methylene group increments and differences in the retention indices (dI) of isomers of alkylbenzenes up to C16 on squalane and acetyltri-n-butyl citrate was studied. The methylene group increments appear to vary over a wide range (60–100

Novel management of methylene blue extravasation: A case report and review of literature

Directory of Open Access Journals (Sweden)

Rashid Saeed Khokhar

2015-01-01

Full Text Available Methylene blue is a highly irritant drug and has been used intraoperatively. Its accidental extravasation can lead to tissue necrosis. In this report, a unique management is described, and the patient recovered without any morbidity.

Removal of methylene blue dye from wastewater by using supported liquid memberane technology

Directory of Open Access Journals (Sweden)

Ashraf Muhammad Waqar

2016-06-01

Full Text Available The present work describes the application of Supported Liquid Membrane (SLM technology towards the removal and recovery of a cationic dye (Methylene Blue from aqueous solutions. Natural and non-toxic vegetable oils have been impregnated on microporous polymeric films of polyvinylidene fluoride (PVDF to constitute a liquid membrane. Different parameters affecting the transport, like pH of feed solution, acid concentration in the strip solution, initial dye concentration, oil types and stirring speeds have been investigated. Highest value of flux (1.7 × 10−5 mg/cm2/sec1 for methylene blue dye was achieved with sunflower oil impregnated on the PVDF support, with pH maintained at 12 in the feed solution and 0.3 M hydrochloric acid concentration in the strip solution. It took 6 hours to transport maximum amount of dye under optimum conditions.

Kinetics analysis for development of a rate constant estimation model for ultrasonic degradation reaction of methylene blue.

Science.gov (United States)

Kobayashi, Daisuke; Honma, Chiemi; Matsumoto, Hideyuki; Takahashi, Tomoki; Kuroda, Chiaki; Otake, Katsuto; Shono, Atsushi

2014-07-01

Ultrasound has been used as an advanced oxidation method for wastewater treatment. Sonochemical degradation of organic compounds in aqueous solution occurs by pyrolysis and/or reaction with hydroxyl radicals. Moreover, kinetics of sonochemical degradation has been proposed. However, the effect of ultrasonic frequency on degradation rate has not been investigated. In our previous study, a simple model for estimating the apparent degradation rate of methylene blue was proposed. In this study, sonochemical degradation of methylene blue was performed at various frequencies. Apparent degradation rate constant was evaluated assuming that sonochemical degradation of methylene blue was a first-order reaction. Specifically, we focused on effects of ultrasonic frequency and power on rate constant, and the applicability of our proposed model was demonstrated. Using this approach, maximum sonochemical degradation rate was observed at 490 kHz, which agrees with a previous investigation into the effect of frequency on the sonochemical efficiency value evaluated by KI oxidation dosimetry. Degradation rate increased with ultrasonic power at every frequency. It was also observed that threshold power must be reached for the degradation reaction to progress. The initial methylene blue concentration and the apparent degradation rate constant have a relation of an inverse proportion. Our proposed model for estimating the apparent degradation rate constant using ultrasonic power and sonochemical efficiency value can apply to this study which extended the frequency and initial concentration range. Copyright © 2013 Elsevier B.V. All rights reserved.

ELECTROCHEMICAL BEHAVIOUR OF METHYLENE BLUE IN NON-AQUEOUS SOLVENTS

International Nuclear Information System (INIS)

Caram, J.A.; Suárez, J.F. Martínez; Gennaro, A.M.; Mirífico, M.V.

2015-01-01

Graphical abstract: Display Omitted - Highlights: • The dye is electro-reduced in two separated monoelectronic charge transfers. • Solvent/supporting electrolyte/acid/base modifies the electrochemical parameters. • A dissociation equilibrium of the dye in non-aqueous solvent is proposed. • The electro-generated and stable dye-radical is also chemically produced in EDA or KOH/DMF. • A new species is reversibly formed in KOH/EtOH or ACN. - Abstract: The electrochemical behaviour of methylene blue in solution of non-aqueous solvents with different supporting electrolytes was studied by cyclic voltammetry. Dye electro-reduction presents two well-defined processes of monoelectronic charge transfer yielding a free radical in the first process and an anion in the second electron transfer. Free radical and anion are long living species in some of the studied media. Effects of supporting electrolyte and solvent on the peak potentials, the peak current functions and the reversibility of the charge transfer processes are reported. A dissociation equilibrium of the dye in solution of non-aqueous solvents and the acid or base added determine markedly the electrochemical responses. In the particular cases of KOH/DMF or EDA basic media the chemical formation of the stable methylene blue radical was detected and it was characterized by EPR spectroscopy. A general reaction scheme is proposed

[Technical aspects of treatments with single- and multi-unit fixed dental prostheses

NARCIS (Netherlands)

Wiersema, E.J.; Kreulen, C.M.; Latzke, P.; Witter, D.J.; Creugers, N.H.J.

2014-01-01

For the manufacture of single- and multi-unit fixed dental prostheses, effective communication between dentist and dental technician is required. Mutual insight concerning the (im)possibilities of available treatments and technical options is prerequisitefor this communication. The manufacture of

Enhanced removal of Methylene Blue by electrocoagulation using iron electrodes

OpenAIRE

Mohamed S. Mahmoud; Joseph Y. Farah; Taha E. Farrag

2013-01-01

The removal of pollutants from effluents by electrocoagulation has become an attractive method in recent years. The study deals with the enhancement of removal of Methylene Blue dye by using an electromagnetic field during the electrocoagulation process. Effects of electrolyte concentration, dye concentration, intensity and the direction of the electromagnet on the decolorization efficiency have been investigated. The formed ferric hydroxide flocs trap colloidal particles and make solid–liqui...

Enhanced visible light photocatalytic degradation of methylene blue by F-doped TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Yu, Wei [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China); Liu, Xinjuan, E-mail: lxj669635@126.com [Shanghai Nanotechnlogy Promotion Center, Shanghai 200237 (China); Center for Coordination Bond and Electronic Engineering, College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Pan, Likun, E-mail: lkpan@phy.ecnu.edu.cn [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China); Li, Jinliang; Liu, Junying [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China); Zhang, Jing; Li, Ping; Chen, Chen [Shanghai Nanotechnlogy Promotion Center, Shanghai 200237 (China); Sun, Zhuo [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 (China)

2014-11-15

Graphical abstract: F-doped TiO2 is synthesized using a modified sol–gel method for visible photocatalytic degradation of MB with a high degradation rate of 91%. - Highlights: • F-doped TiO{sub 2} are synthesized using a modified sol–gel method. • The photocatalytic degradation of methylene blue by F-doped TiO{sub 2} is investigated. • A high methylene blue degradation rate of 91% is achieved under visible light irradiation. - Abstract: F-doped TiO{sub 2} (F-TiO{sub 2}) were successfully synthesized using a modified sol–gel method. The morphologies, structures, and photocatalytic performance in the degradation of methylene blue (MB) were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, UV–vis absorption spectroscopy, and electrochemical impedance spectra, respectively. The results show that F-TiO{sub 2} exhibits an enhanced photocatalytic performance in the degradation of MB with a maximum degradation rate of 91% under visible light irradiation as compared with pure TiO{sub 2} (32%). The excellent photocatalytic activity is due to the contribution from the increased visible light absorption, promoted separation of photo-generated electrons and holes as well as enhanced photocatalytic oxidizing species with the doping of F in TiO{sub 2}.

Synergistic effect of pulsed corona discharges and ozonation on decolourization of methylene blue in water

International Nuclear Information System (INIS)

Malik, Muhammad Arif; Ubaid-ur-Rehman; Ghaffar, Abdul; Ahmed, Kurshid

2002-01-01

The effect of O 2 and O 3 bubbling on decolourization of methylene blue by pulsed corona discharges in water was studied. The pulsed corona discharges were produced by charging an 80 pF capacitor with a 40 kV DC source, through a 100 MΩ resistor, and discharging it into a needle-plate type reactor at 60 Hz through a rotating spark gap switch. A 20 ml sample of 13.25 mg l -1 methylene blue in distilled water was decolourized in 120 min. Bubbling O 2 at 10 ml min -1 through the discharge region reduced the decolourization time to 25 min. Bubbling O 2 containing 1500 μmol O 3 l -1 at 10 ml min -1 reduced the decolourization time to 8 min. The O 3 was produced by fractionating input energy between a water treatment reactor and a O 3 generator, i.e. no additional energy was consumed for O 3 production. Under the same experimental conditions methylene blue solution in tap water was decolourized in >210 min by corona discharge in solution, in 30 min by corona discharge with O 2 bubbling, and in 11 min by corona discharge with bubbling of O 2 containing 1500 μmol O 3 l -1

Coconut Husk Adsorbent for the Removal of Methylene Blue Dye from Wastewater

Directory of Open Access Journals (Sweden)

Hasfalina Che bt Man

2015-03-01

Full Text Available A study to assess the efficiency of coconut husks (CHs in removing methylene blue (MB dye from wastewaters in Malaysia was carried out. A fixed bed column adsorber was set up using flow rates of 40 and 80 mL/min, and the adsorbent (CH was prepared using the base treatment method with NaOH as activating agent. Three different column bed depths (10, 20, and 25 cm and unit weights of adsorbent (103, 213, and 260 g were used. Two models, the bed depth service time (BDST and Thomas models, were used to validate the adsorption capacity results and breakthrough curve. Changing the bed depth from 20 to 25 cm did not result in a significant change in adsorption capacity, therefore a 20-cm bed depth is recommended as the most efficient. Similarly, adsorption capacity increased as flow rates increased from 40 to 80 mL/min, indicating that a flow rate of 80 mL/min yielded optimum efficiency. The two models also provided predictions with good fits of the bed depth effect, the adsorption capacity, and the breakthrough curve of CH for MB removal.

Adsorption capacity of methylene blue, an organic pollutant, by montmorillonite clay

KAUST Repository

Feddal, I.; Ramdani, Amina; Taleb, Safia; Gaigneaux, E. M.; Batis, Narjè s Harrouch; Ghaffour, NorEddine

2013-01-01

The isotherms and kinetics of the adsorption of a cationic dye in aqueous solution, methylene blue, on a local Algerian montmorillonite clay mineral (raw, sodium and thermally activated at 300 and 500°C) were determined experimentally. Various parameters influencing the adsorption were optimized, mainly solid-liquid contact time, mass of adsorbent, initial concentration of dye, pH of the solution and temperature. Results showed that the adsorption kinetics were fast: 30 min for the raw clay mineral, and 20 min for sodium clay mineral (SC) and thermally activated at 300°C, whereas with the clay mineral calcined at 500°C, the equilibrium was reached after 150 min only. The maximum adsorption capacity was reached at pH 6.6. Results deducted from the adsorption isotherms also showed that the retention follows the Langmuir model. In addition, it was found that the kinetics were in the order of 2 (K = 2.457 × 106 g/mg.h) for sodium clay and were limited by an intra-particle diffusion. SC was found to be a better adsorbent to remove methylene blue from industrial wastewater. © 2013 Balaban Desalination Publications. All rights reserved.

Adsorption capacity of methylene blue, an organic pollutant, by montmorillonite clay

KAUST Repository

Feddal, I.

2013-11-19

The isotherms and kinetics of the adsorption of a cationic dye in aqueous solution, methylene blue, on a local Algerian montmorillonite clay mineral (raw, sodium and thermally activated at 300 and 500°C) were determined experimentally. Various parameters influencing the adsorption were optimized, mainly solid-liquid contact time, mass of adsorbent, initial concentration of dye, pH of the solution and temperature. Results showed that the adsorption kinetics were fast: 30 min for the raw clay mineral, and 20 min for sodium clay mineral (SC) and thermally activated at 300°C, whereas with the clay mineral calcined at 500°C, the equilibrium was reached after 150 min only. The maximum adsorption capacity was reached at pH 6.6. Results deducted from the adsorption isotherms also showed that the retention follows the Langmuir model. In addition, it was found that the kinetics were in the order of 2 (K = 2.457 × 106 g/mg.h) for sodium clay and were limited by an intra-particle diffusion. SC was found to be a better adsorbent to remove methylene blue from industrial wastewater. © 2013 Balaban Desalination Publications. All rights reserved.

A Novel ZnO-Methylene Blue Nanocomposite Matrix for Biosensing Application

Directory of Open Access Journals (Sweden)

Shibu Saha

2011-01-01

Full Text Available A novel hybrid matrix of zinc oxide-methylene blue (ZnO-MB has been successfully developed for biosensing application. The introduction of methylene blue into the ZnO thin film leads to reduction in the charge transfer resistance and suggests an increase in the electron transfer capacity of the composite. Glucose oxidase (GOx was chosen as the model enzyme and effectively immobilized on the surface of hybrid ZnO-MB nanocomposite matrix. Electrochemical measurements were employed to study biosensing response of the GOx/ZnO-MB/ITO bioelectrode as a function of glucose concentration. The low oxidation potential (−0.23 V of the hybrid bioelectrode, in a mediatorless electrolyte, makes it resistant against interference from other bio-molecules. The low value of Michaelis-Menten constant (2.65 mM indicates that immobilized GOx retains its enzymatic activity significantly on the surface of nanocomposite hybrid matrix that results in an enhanced affinity towards its substrate (glucose. The ZnO-MB nanocomposite hybrid matrix, exhibiting enhanced sensing response (0.2 μAmM−1cm−2 with long shelf-life (>10 weeks, has potential for the realization of an integrated biosensing device.

Photocatalytic degradation of methylene blue by C 3 N 4 /ZnO

Indian Academy of Sciences (India)

The photocatalytic activities of prepared samples were investigated under the illumination of blacklight and fluorescent lamps as the low wattage light source. The C 3 N 4 /ZnO showed a better photocatalytic activity than ZnO to degrade a methylene blue (MB) dye solution using blacklight lamps, but there is no significant ...

Solar-powered single-and double-effect directly air-cooled LiBr–H2O absorption prototype built as a single unit

International Nuclear Information System (INIS)

Izquierdo, M.; González-Gil, A.; Palacios, E.

2014-01-01

Highlights: • This work presents a novel solar cooling air-cooled absorption prototype for buildings. • The solution (LiB r –H 2 O) and the refrigerant (H 2 O) are cooled directly by air. • The cooling is produced from solar energy when operates in single-effect mode. • If the demand is not met the prototype is able to operate in double-effect mode. - Abstract: This work describes an installation in Madrid, Spain, designed to test a new solar-powered air-cooled absorption refrigeration system. This installation essentially consists of a-48 m 2 field of flat-plate solar collectors, a 1500-L hot water storage tank and a single and-double effect air-cooled lithium bromide absorption prototype. Designed and built by our research group, this prototype is able to operate either as a single-effect unit (4.5 kW) or as a double-effect unit (7 kW). In operation as single-effect mode, the prototype is driven by solar energy, whereas in operation as a double effect mode, an external energy source may be used. The prototype’s evaporator is connected to a fan-coil placed inside an 80-m 2 laboratory that represent the average size of a Spanish housing unit. In August 2009, the cooling system was tested in the single-effect operation mode. The results show that the system is able to meet approximately 65% of the laboratory’s seasonal cooling demand, although 100% may be reached for a few days. The prototype can also operate in double-effect mode to meet the cooling demand. In that case, the prototype is fed by thermal oil, which is warmed until it reaches the process temperature in the high-temperature generator. The prototype can operate in either single-effect mode or in double-effect mode or can also operate simultaneously both modes using the components common to both modes, namely, the absorber, evaporator, condenser, solution pumps and control equipment. This paper reports the experimental results from the prototype operating separately in single-effect and

Methylene Blue for Vasoplegic Syndrome Postcardiac Surgery

Science.gov (United States)

Habib, Aly Makram; Elsherbeny, Ahmed Galal; Almehizia, Rayd Abdelaziz

2018-01-01

Objectives: cardiopulmonary bypass (CPB) can be complicated by vasoplegia that is refractory to vasopressors. Methylene blue (MB) represents an alternative in such cases. Patients and Methods: Retrospective observational historical control-matched study. From 2010 to 2015, all patients who received MB for vasoplegia post-CPB were included in this study. Historical controls from the period of 2004 to 2009 were matched. End-points were the time till improvement of vasoplegia (Ti), 30-day mortality, cardiac surgical Intensive Care Unit (CSICU) morbidity, and length of stay (LOS). Results: Twenty-eight patients were matched in both groups. There were no statistically significant differences between the two groups in demographic, laboratory data on admission, or hemodynamic profile before use of MB. Ti and time to complete discontinuation of vasopressors were statistically significant less in MB group (8.2 ± 2.6 vs. 29.7 ± 6.4, P = 0.00 and 22.6 ± 5.2 vs. 55.3 ± 9.4, P = 0.00) respectively. Mortality at day 30 was significantly higher in controls compared to MB (1 patient [3.6%] vs. 6 patients [21.4%], long rank P = 0.04). CSICU, hospital LOS, and incidence of renal failure was significantly higher in control group (12.4 ± 3.7 vs. 7 ± 1.4, P = 0.03), (19.5 ± 2.4 vs. 10.9 ± 3.2, P = 0.05) and (9 patients [32.1%] vs. 2 patients [7.1%], P = 0.04), respectively. Duration of mechanical ventilation was less in MB patients; however, did not reach statistical significance. Conclusions: the use of MB for vasoplegia postcardiac surgery was associated with rapid recovery of hemodynamics, shorter need for vasopressors, less ICU mortality, less incidence of renal failure, and shorter LOS. PMID:29657374

Synthesis and properties of Co-doped titanate nanotubes and their optical sensitization with methylene blue

International Nuclear Information System (INIS)

Ferreira, V.C.; Nunes, M.R.; Silvestre, A.J.; Monteiro, O.C.

2013-01-01

Here we report on a novel chemical route to synthesize homogenous cobalt-doped titanate nanotubes (CoTNT), using an amorphous Co-doped precursor. The influence of the synthesis temperature, autoclave dwell time and metal doping on the structural and microstructural as well as on the optical properties of the synthesized titanate nanotubes is studied and discussed. The optical band gaps of the CoTNT samples are red shifted in comparison with the values determined for the undoped samples, such red shifts bringing the absorption edge of the CoTNT samples into the visible region. CoTNT materials also demonstrate particular high adsorption ability for methylene blue, the amount of the adsorbed dye being higher than the one predictable for a monolayer formation. This suggests the possibility of intercalation of the dye molecule between the TiO 6 layers of the TNT structure. It is also shown that the methylene blue sensitized Co-doped nanostructures are highly stable under UV radiation and present a strong and broad absorption in the visible region. - Highlights: • New hydrothermal chemical route to synthesize cobalt-doped titanate nanotubes. • The Co-doping stabilizes the TNTs morphology in a temperature range of 160–200 °C. • Optical band gaps of CoTNTs are red shifted compared to the TNT samples. • Methylene blue sensitized CoTNTs are highly stable under UV–vis irradiation

Synergistic effect of pulsed corona discharges and ozonation on decolourization of methylene blue in water

Energy Technology Data Exchange (ETDEWEB)

Malik, Muhammad Arif [Applied Chemistry Division, PINSTECH, PO Nilore, Islamabad (Pakistan); Ubaid-ur-Rehman [Applied Chemistry Division, PINSTECH, PO Nilore, Islamabad (Pakistan); Ghaffar, Abdul; Ahmed, Kurshid [Electronics Division, PINSTECH, PO Nilore, Islamabad (Pakistan)

2002-08-01

The effect of O{sub 2} and O{sub 3} bubbling on decolourization of methylene blue by pulsed corona discharges in water was studied. The pulsed corona discharges were produced by charging an 80 pF capacitor with a 40 kV DC source, through a 100 M{omega} resistor, and discharging it into a needle-plate type reactor at 60 Hz through a rotating spark gap switch. A 20 ml sample of 13.25 mg l{sup -1} methylene blue in distilled water was decolourized in 120 min. Bubbling O{sub 2} at 10 ml min{sup -1} through the discharge region reduced the decolourization time to 25 min. Bubbling O{sub 2} containing 1500 {mu}mol O{sub 3} l{sup -1} at 10 ml min{sup -1} reduced the decolourization time to 8 min. The O{sub 3} was produced by fractionating input energy between a water treatment reactor and a O{sub 3} generator, i.e. no additional energy was consumed for O{sub 3} production. Under the same experimental conditions methylene blue solution in tap water was decolourized in >210 min by corona discharge in solution, in 30 min by corona discharge with O{sub 2} bubbling, and in 11 min by corona discharge with bubbling of O{sub 2} containing 1500 {mu}mol O{sub 3} l{sup -1}.

Synthesis and properties of Co-doped titanate nanotubes and their optical sensitization with methylene blue

Energy Technology Data Exchange (ETDEWEB)

Ferreira, V.C. [University of Lisbon, Faculty of Sciences, Department of Chemistry and Biochemistry and CQB, Campo Grande, 1749-016 Lisboa (Portugal); Nunes, M.R. [University of Lisbon, Faculty of Sciences, Department of Chemistry and Biochemistry and CCMM, Campo Grande, 1749-016 Lisboa (Portugal); Silvestre, A.J. [Instituto Superior de Engenharia de Lisboa, Department of Physics and ICEMS, R. Conselheiro Emídio Navarro 1, 1959-007 Lisboa (Portugal); Monteiro, O.C., E-mail: ocmonteiro@fc.ul.pt [University of Lisbon, Faculty of Sciences, Department of Chemistry and Biochemistry and CQB, Campo Grande, 1749-016 Lisboa (Portugal)

2013-10-01

Here we report on a novel chemical route to synthesize homogenous cobalt-doped titanate nanotubes (CoTNT), using an amorphous Co-doped precursor. The influence of the synthesis temperature, autoclave dwell time and metal doping on the structural and microstructural as well as on the optical properties of the synthesized titanate nanotubes is studied and discussed. The optical band gaps of the CoTNT samples are red shifted in comparison with the values determined for the undoped samples, such red shifts bringing the absorption edge of the CoTNT samples into the visible region. CoTNT materials also demonstrate particular high adsorption ability for methylene blue, the amount of the adsorbed dye being higher than the one predictable for a monolayer formation. This suggests the possibility of intercalation of the dye molecule between the TiO{sub 6} layers of the TNT structure. It is also shown that the methylene blue sensitized Co-doped nanostructures are highly stable under UV radiation and present a strong and broad absorption in the visible region. - Highlights: • New hydrothermal chemical route to synthesize cobalt-doped titanate nanotubes. • The Co-doping stabilizes the TNTs morphology in a temperature range of 160–200 °C. • Optical band gaps of CoTNTs are red shifted compared to the TNT samples. • Methylene blue sensitized CoTNTs are highly stable under UV–vis irradiation.

Kinetics and equilibrium studies on removal of methylene blue and methyl orange by adsorption onto activated carbon prepared from date pits-A comparative study

International Nuclear Information System (INIS)

Mahmoudi, Khaled; Hosni, Khaled; Hamdi, Noureddine; Srasra, Ezzeddine

2015-01-01

The adsorption of Methylene blue and Methyl orange by date pits carbon was carried out by varying parameters such as agitation time, pH and dye concentration. Equilibrium adsorption data followed both Langmuir and Freundlich isotherms. Adsorption followed second-order rate kinetics. The adsorption capacity was found to be 434 and 455mg of methyl orange and methylene blue, respectively, per g of the date pits carbon. Acidic pH is favorable for the adsorption of methyl orange against a basic medium which is favorable for the adsorption of MB. An opposite result was found for the methylene blue adsorption

Use of ZnO:Mn particles for degradation of methylene blue by photocatalysis process; Utilizacao de particulas de ZnO:Mn para a degradacao do azul de metileno por processo de fotocatalise

Energy Technology Data Exchange (ETDEWEB)

Giraldi, T. R.; Swerts, J. P.; Vicente, M. A., E-mail: tania.giraldi@unifal-mg.edu.br, E-mail: jefersonps21@hotmail.com, E-mail: maquelyaspr@oi.com.br [Universidade Federal de Alfenas (UNIFAL), Pocos de Caldas, MG (Brazil). Instituto de Ciencia e Tecnologia; Mendonca, V.R. de, E-mail: vrm@ifsp.edu.br [Instituto Federal de Educacao, Ciencia e Tecnologia de Sao Paulo (IFSP), Itapetininga, SP (Brazil); Paris, E.C.; Ribeiro, C., E-mail: elaine.paris@embrapa.br, E-mail: caue.ribeiro@embrapa.br [Embrapa Instrumentacao, Sao Carlos, SP (Brazil)

2016-10-15

The management of water use in the agricultural environment is a key factor to build new environmentally sustainable productive methods. Photocatalysis is a promising method for water decontamination. This research paper aimed to evaluate the photocatalytic potential of pure and Mn-doped ZnO particles. The materials were obtained by the polymeric precursor method, and characterized by X-ray diffraction, N{sub 2} adsorption in low temperature, infrared and ultraviolet spectroscopy, and photoluminescence. In order to evaluate ZnO:Mn particles photo efficiency, experiments were carried out by applying the methylene blue dye solution to photodegradation under UVC exposure. The particles had ZnO single-phase, but low specific surface area. The sample ZnO:0.25% Mn presented higher efficiency in the methylene blue photocatalytic degradation test. This efficiency was related to a higher band gap energy value and a lower rate of electron recombination, which allows greater formation of hydroxyl radicals, which are responsible for dye degradation. (author)

An unusual methylene aziridine refined in P2(1)/c and the nonstandard setting P2(1)/n.

Science.gov (United States)

Feast, George C; Haestier, James; Page, Lee W; Robertson, Jeremy; Thompson, Amber L; Watkin, David J

2009-12-01

The unusual methylene aziridine 6-tert-butyl-3-oxa-2-thia-1-azabicyclo[5.1.0]oct-6-ene 2,2-dioxide, C(9)H(15)NO(3)S, was found to crystallize with two molecules in the asymmetric unit. The structure was solved in both the approximately orthogonal and the oblique settings of space group No. 14, viz. P2(1)/n and P2(1)/c, respectively. A comparison of these results clearly displayed an increase in the correlation between coordinates in the ac plane for the oblique cell. The increase in the corresponding covariances makes a significant contribution to the standard uncertainties of derived parameters, e.g. bond lengths. Since there is yet no CIF definition for the full variance-covariance matrix, there are clear advantages to reporting the structure in the nonstandard space-group setting.

Decolorization of Methylene Blue with TiO2 Sol via UV Irradiation Photocatalytic Degradation

Directory of Open Access Journals (Sweden)

Jun Yao

2010-01-01

Full Text Available TiO2 sol was prepared for the degradation of methylene blue (MB solution under ultraviolet (UV irradiation. The absorption spectra of MB indicated that the maximum wavelength, 663 nm, almost kept the same. The performance of 92.3% for color removal was reached after 160 min. The particle size of TiO2 sol was about 22.5 nm. X-ray diffraction showed that TiO2 consisted of a single anatase phase. The small size and anatase phase probably resulted in high photocatalytic activity of TiO2 sol. The degradation ratio decreased as the initial concentration of MB increased. The photodegradation efficiency decreased in the order of pH 2>pH 9>pH 7. Regarding catalyst load, the degradation increased with the mass of catalyst up to an amount of 1.5 g⋅L−1 then decreased as the mass continued to increase. The addition of H2O2 to TiO2 sol resulted in an increase on the degradation ratio.

Application of a genetic algorithm in the conformational analysis of methylene-acetal-linked thymine dimers in DNA: Comparison with distance geometry calculations

International Nuclear Information System (INIS)

Beckers, Mischa L.M.; Buydens, Lutgarde M.C.; Pikkemaat, Jeroen A.; Altona, Cornelis

1997-01-01

The three-dimensional spatial structure of a methylene-acetal-linked thymine dimer present in a 10 base-pair (bp) sense-antisense DNA duplex was studied with a genetic algorithm designed to interpret NOE distance restraints. Trial solutions were represented by torsion angles. This means that bond angles for the dimer trial structures are kept fixed during the genetic algorithm optimization. Bond angle values were extracted from a 10 bp sense-antisense duplex model that was subjected to energy minimization by means of a modified AMBER force field. A set of 63 proton-proton distance restraints defining the methylene-acetal-linked thymine dimer was available. The genetic algorithm minimizes the difference between distances in the trial structures and distance restraints. A large conformational search space could be covered in the genetic algorithm optimization by allowing a wide range of torsion angles. The genetic algorithm optimization in all cases led to one family of structures. This family of the methylene-acetal-linked thymine dimer in the duplex differs from the family that was suggested from distance geometry calculations. It is demonstrated that the bond angle geometry around the methylene-acetal linkage plays an important role in the optimization

Graphene oxide (rGO)-metal oxide (TiO2/Fe3O4) based nanocomposites for the removal of methylene blue

Science.gov (United States)

Banerjee, Soma; Benjwal, Poonam; Singh, Milan; Kar, Kamal K.

2018-05-01

Herein, ternary nanocomposites based on titanium dioxide, ferric oxide and reduced graphene oxide (GO) have been developed for photocatalytic degradation of methylene blue. The nanocomposites are prepared by simple sol-gel and wet assembly methods with varying weight ratio of each components to obtain efficient photocatalytic degradation. Due to the synergistic effect among the three components, a swift removal of methylene blue becomes possible under visible and UV light. The rGO-Fe3O4-TiO2 nanocomposite having composition 1:1:2 has achieved maximum degradation of methylene blue from the aqueous solution. About 99% of the dye has been removed within 6 min under UV irradiation, while in presence of visible light, 94% has been degraded from the wastewater. The enhancement of photocatalytic activity in this ternary system is attributed to the efficient separation of charge carriers from TiO2 to rGO under the exposure of light and the initiation of photo-Fenton reaction due to the incorporated Fe3O4 nanoparticles in presence of H2O2, which provides highly reactive hydroxyl ions that mineralize the pollutants. All these results indicate that these ternary nanocomposites possess great potential for both UV and visible light driven methylene blue destruction from the wastewater.

Solvent mimicry with methylene carbene to probe protein topography.

Science.gov (United States)

Gómez, Gabriela Elena; Monti, José Luis E; Mundo, Mariana Rocío; Delfino, José María

2015-10-06

The solvent accessible surface area (SASA) of the polypeptide chain plays a key role in protein folding, conformational change, and interaction. This fundamental biophysical parameter is elusive in experimental measurement. Our approach to this problem relies on the reaction of the minimal photochemical reagent diazirine (DZN) with polypeptides. This reagent (i) exerts solvent mimicry because its size is comparable to water and (ii) shows scant chemical selectivity because it generates extremely reactive methylene carbene. Methylation gives rise to the EM (extent of modification) signal, which is useful for scrutinizing the conformational change triggered by Ca(2+) binding to calmodulin (CaM). The increased EM observed for the full protein is dominated by the enhanced exposure of hydrophobic area in Ca(2+)-CaM. Fragmentation allowed us to quantify the methylene incorporation at specific sites. Peptide 91-106 reveals a major reorganization around the calcium 151 binding site, resulting in local ordering and a greater exposure of the hydrophobic surface. Additionally, this technique shows a high sensitivity to probe recognition between CaM and melittin (Mel). The large decrease in EM indicates the occlusion of a significant hydrophobic area upon complexation. Protection from labeling reveals a larger involvement of the N-terminal and central regions of CaM in this interaction. Despite its smaller size, Mel's differential exposure can also be quantified. Moreover, MS/MS fragmentation realizes the goal of extending the resolution of labeled sites at the amino acid level. Overall, DZN labeling emerges as a useful footprinting method capable of shedding light on physiological conformational changes and interactions.

3D Oxidized Graphene Frameworks: An Efficient Adsorbent for Methylene Blue

Science.gov (United States)

Pandey, Abhishek; Deb, Madhurima; Tiwari, Shreya; Pawar, Pranav Bhagwan; Saxena, Sumit; Shukla, Shobha

2018-04-01

Extraordinary properties of graphene and its derivatives have found application in varied areas such as energy, electronics, optical devices and sensors, to name a few. Large surface area along with specialized functional groups make these materials attractive for removal of dye molecules in solution via adsorption. Industrial effluents contain large amounts of toxic chemicals resulting in pollution of water bodies, which pose environmental hazards in general. Here we report application of 3D oxidized graphene frameworks in the efficient removal of cationic dye molecules such as methylene blue via adsorption. Systematic parametric studies investigating the effect of the initial dye concentration, pH and contact time have been performed. Spectroscopic analysis of the filtrate suggests that tortuous paths in 3D oxidized graphene frameworks result in efficient removal of dye molecules due to enhanced interaction. The hydroxyl groups retained in these 3D oxidized graphene frameworks facilitate adsorption of the dye molecules while passing through the adsorbent. pH studies suggest that maximum removal efficiency for methylene blue was achieved at pH value of 9. The results suggest that these 3D oxidized graphene frameworks can be used for purification of large volumes of contaminated water from cationic dyes in waste water treatment plants.

[Loading and strength of single- and multi-unit fixed dental prostheses 2. Strength

NARCIS (Netherlands)

Baat, C. de; Witter, D.J.; Meijers, C.C.A.J.; Vergoossen, E.L.; Creugers, N.H.J.

2014-01-01

The ultimate strength of a dental prosthesis is defined as the strongest loading force applied to the prosthesis until afracture failure occurs. Important key terms are strength, hardness, toughness and fatigue. Relatively prevalent complications of single- and multi-unit fixed dental prostheses are

Sulfonamide antibiotic removal and nitrogen recovery from synthetic urine by the combination of rotating advanced oxidation contactor and methylene urea synthesis process

OpenAIRE

Fukahori, S.; Fujiwara, T.; Ito, R.; Funamizu, N.

2015-01-01

The combination of nitrogen recovery and pharmaceutical removal processes for livestock urine treatment were investigated to suppress the discharge of pollutants and recover nitrogen as resources. We combined methylene urea synthesis from urea and adsorption and photocatalytic decomposition of sulfonamide antibiotic using rotating advanced oxidation contactor (RAOC) contained for obtaining both safe fertilizer and reclaimed water. The methylene urea synthesis could recover urea in synthetic u...

Photocatalytic degradation of methylene blue on magnetically separable MgFe2O4 under visible light irradiation

KAUST Repository

Shahid, Muhammad

2013-05-01

A magnetically separable single-phase MgFe2O4 photocatalyst with a spinel crystal structure was synthesized by using the solid-state reaction method. The formation of spinel structure is confirmed by X-ray diffraction and Fourier transform infrared spectroscopy. The magnetic measurements showed that the photocatalyst material can be separated from water when an external magnetic field is added and redispersed into water solution after the external magnetic field is eliminated. It is one of the promising photocatalysts for waste water treatment. The photocatalytic activity of MgFe2O4 was investigated by using the photo-decomposition of methylene blue dye under visible light. The photoelectrochemical property of the MgFe2O4 was studied by measuring their photocurrent-potential behavior in 1 M NaOH electrolyte under AM 1.5100 mW cm-2 illumination. © 2013 Elsevier B.V. All rights reserved.

Photodynamic effects of methylene blue-loaded polymeric nanoparticles on dental plaque bacteria.

Science.gov (United States)

Klepac-Ceraj, Vanja; Patel, Niraj; Song, Xiaoqing; Holewa, Colleen; Patel, Chitrang; Kent, Ralph; Amiji, Mansoor M; Soukos, Nikolaos S

2011-09-01

Photodynamic therapy (PDT) is increasingly being explored for treatment of oral infections. Here, we investigate the effect of PDT on human dental plaque bacteria in vitro using methylene blue (MB)-loaded poly(lactic-co-glycolic) (PLGA) nanoparticles with a positive or negative charge and red light at 665 nm. Dental plaque samples were obtained from 14 patients with chronic periodontitis. Suspensions of plaque microorganisms from seven patients were sensitized with anionic, cationic PLGA nanoparticles (50 µg/ml equivalent to MB) or free MB (50 µg/ml) for 20 min followed by exposure to red light for 5 min with a power density of 100 mW/cm2 . Polymicrobial oral biofilms, which were developed on blood agar in 96-well plates from dental plaque inocula obtained from seven patients, were also exposed to PDT as above. Following the treatment, survival fractions were calculated by counting the number of colony-forming units. The cationic MB-loaded nanoparticles exhibited greater bacterial phototoxicity in both planktonic and biofilm phase compared to anionic MB-loaded nanoparticles and free MB, but results were not significantly different (P > 0.05). Cationic MB-loaded PLGA nanoparticles have the potential to be used as carriers of MB for PDT systems. Copyright © 2011 Wiley-Liss, Inc.

Microwave atmospheric pressure plasma jets for wastewater treatment: Degradation of methylene blue as a model dye.

Science.gov (United States)

García, María C; Mora, Manuel; Esquivel, Dolores; Foster, John E; Rodero, Antonio; Jiménez-Sanchidrián, César; Romero-Salguero, Francisco J

2017-08-01

The degradation of methylene blue in aqueous solution as a model dye using a non thermal microwave (2.45 GHz) plasma jet at atmospheric pressure has been investigated. Argon has been used as feed gas and aqueous solutions with different concentrations of the dye were treated using the effluent from plasma jet in a remote exposure. The removal efficiency increased as the dye concentration decreased from 250 to 5 ppm. Methylene blue degrades after different treatment times, depending on the experimental plasma conditions. Thus, kinetic constants up to 0.177 min -1 were obtained. The higher the Ar flow, the faster the degradation rate. Optical emission spectroscopy (OES) was used to gather information about the species present in the gas phase, specifically excited argon atoms. Argon excited species and hydrogen peroxide play an important role in the degradation of the dye. In fact, the conversion of methylene blue was directly related to the density of argon excited species in the gas phase and the concentration of hydrogen peroxide in the aqueous liquid phase. Values of energy yield at 50% dye conversion of 0.296 g/kWh were achieved. Also, the use of two plasma applicators in parallel has been proven to improve energy efficiency. Copyright © 2017 Elsevier Ltd. All rights reserved.

Combination photodynamic therapy of human breast cancer using salicylic acid and methylene blue

Science.gov (United States)

Hosseinzadeh, Reza; Khorsandi, Khatereh; Jahanshiri, Maryam

2017-09-01

The objective of this study was to evaluate the effects of combination therapy with methylene blue (MB) assisted photodynamic therapy (PDT) and salicylic acid (SA) as chemo-therapy anticancer agent. The binding of salicylic acid to methylene blue was studied using spectrophotometric method. The results show the 1:2 complex formation between SA and MB. The binding constants and related Gibbs free energies o are obtained (Kb1 = 183.74, Kb2 = 38.13 and ∆ Gb1° = 12.92 kJ·mol- 1, ∆ Gb2° =9.02 kJ·mol- 1). The spectrophotometric results show the improvement in solubilization and reduction prevention for SA and MB in the complex form. These results are in agreements with cellular experiments. The dark toxicity measurements represent the improve efficacy of chemotherapy using combination of SA and MB. The photodynamic therapy results (using red LED as light source (630 nm; power density: 30 mW cm- 2)) show that the cancer cell killing efficiency of MB increases in the combination with SA due to reduction prevention and stabilization of monomeric form of MB.

Removal of methylene blue from aqueous solution by adsorption onto pineapple leaf powder

International Nuclear Information System (INIS)

Weng, Chih-Huang; Lin, Yao-Tung; Tzeng, Tai-Wei

2009-01-01

The ability of an unconventional bio-adsorbent, pineapple leaf powder (PLP) for the adsorption of methylene blue (MB) from aqueous solution was studied. It was observed that intra-particle diffusion was involved in the adsorption process and that the kinetic data fitted well with a pseudo-second-order equation. Fitting parameters revealed that the rate of adsorption increased with decrease in dye concentration and decrease in ionic strength while the mixing speed did not have a significant effect on adsorption. The adsorption was favorable at higher pH and lower temperature, and the equilibrium data were well fitted by the Langmuir isotherm. The maximum adsorption capacity varied from 4.68 x 10 -4 to 9.28 x 10 -4 mol/g when pH increases from 3.5 to 9.5. Thermodynamic parameters suggest that the adsorption is a typical physical process, spontaneous, and exothermic in nature. The results revealed that this agricultural waste has potential to be used as an economical adsorbent for the removal of methylene blue from aqueous solution.

Removal of methylene blue from aqueous solution by adsorption onto pineapple leaf powder

Energy Technology Data Exchange (ETDEWEB)

Weng, Chih-Huang, E-mail: chweng@isu.edu.tw [Department of Civil and Ecological Engineering, I-Shou University, Da-Hsu Township, Kaohsiung 84008, Taiwan (China); Lin, Yao-Tung; Tzeng, Tai-Wei [Department of Soil and Environmental Sciences, National Chung Hsing University, TaiChung 40227, Taiwan (China)

2009-10-15

The ability of an unconventional bio-adsorbent, pineapple leaf powder (PLP) for the adsorption of methylene blue (MB) from aqueous solution was studied. It was observed that intra-particle diffusion was involved in the adsorption process and that the kinetic data fitted well with a pseudo-second-order equation. Fitting parameters revealed that the rate of adsorption increased with decrease in dye concentration and decrease in ionic strength while the mixing speed did not have a significant effect on adsorption. The adsorption was favorable at higher pH and lower temperature, and the equilibrium data were well fitted by the Langmuir isotherm. The maximum adsorption capacity varied from 4.68 x 10{sup -4} to 9.28 x 10{sup -4} mol/g when pH increases from 3.5 to 9.5. Thermodynamic parameters suggest that the adsorption is a typical physical process, spontaneous, and exothermic in nature. The results revealed that this agricultural waste has potential to be used as an economical adsorbent for the removal of methylene blue from aqueous solution.

Ionic imbalance and lack of effect of adjuvant treatment with methylene blue in the hamster model of leptospirosis

Directory of Open Access Journals (Sweden)

Cleiton Silva Santos

2013-06-01

Full Text Available Leptospirosis in humans usually involves hypokalaemia and hypomagnesaemia and the putative mechanism underlying such ionic imbalances may be related to nitric oxide (NO production. We previously demonstrated the correlation between serum levels of NO and the severity of renal disease in patients with severe leptospirosis. Methylene blue inhibits soluble guanylyl cyclase (downstream of the action of any NO synthase isoforms and was recently reported to have beneficial effects on clinical and experimental sepsis. We investigated the occurrence of serum ionic changes in experimental leptospirosis at various time points (4, 8, 16 and 28 days in a hamster model. We also determined the effect of methylene blue treatment when administered as an adjuvant therapy, combined with late initiation of standard antibiotic (ampicillin treatment. Hypokalaemia was not reproduced in this model: all of the groups developed increased levels of serum potassium (K. Furthermore, hypermagnesaemia, rather than magnesium (Mg depletion, was observed in this hamster model of acute infection. These findings may be associated with an accelerated progression to acute renal failure. Adjuvant treatment with methylene blue had no effect on survival or serum Mg and K levels during acute-phase leptospirosis in hamsters.

Multiple single-unit long-term tracking on organotypic hippocampal slices using high-density microelectrode arrays

Directory of Open Access Journals (Sweden)

Wei Gong

2016-11-01

Full Text Available A novel system to cultivate and record from organotypic brain slices directly on high-density microelectrode arrays (HD-MEA was developed. This system allows for continuous recording of electrical activity of specific individual neurons at high spatial resolution while monitoring at the same time, neuronal network activity. For the first time, the electrical activity patterns of single neurons and the corresponding neuronal network in an organotypic hippocampal slice culture were studied during several consecutive weeks at daily intervals. An unsupervised iterative spike-sorting algorithm, based on PCA and k-means clustering, was developed to assign the activities to the single units. Spike-triggered average extracellular waveforms of an action potential recorded across neighboring electrodes, termed ‘footprints’ of single-units were generated and tracked over weeks. The developed system offers the potential to study chronic impacts of drugs or genetic modifications on individual neurons in slice preparations over extended times.

Ia Afferent input alters the recruitment thresholds and firing rates of single human motor units.

Science.gov (United States)

Grande, G; Cafarelli, E

2003-06-01

Vibration of the patellar tendon recruits motor units in the knee extensors via excitation of muscle spindles and subsequent Ia afferent input to the alpha-motoneuron pool. Our first purpose was to determine if the recruitment threshold and firing rate of the same motor unit differed when recruited involuntarily via reflex or voluntarily via descending spinal pathways. Although Ia input is excitatory to the alpha-motoneuron pool, it has also been shown paradoxically to inhibit itself. Our second purpose was to determine if vibration of the patellar tendon during a voluntary knee extension causes a change in the firing rate of already recruited motor units. In the first protocol, 10 subjects voluntarily reproduced the same isometric force profile of the knee extensors that was elicited by vibration of the patellar tendon. Single motor unit recordings from the vastus lateralis (VL) were obtained with tungsten microelectrodes and unitary behaviour was examined during both reflex and voluntary knee extensions. Recordings from 135 single motor units showed that both recruitment thresholds and firing rates were lower during reflex contractions. In the second protocol, 7 subjects maintained a voluntary knee extension at 30 N for approximately 40-45 s. Three bursts of patellar tendon vibration were superimposed at regular intervals throughout the contraction and changes in the firing rate of already recruited motor units were examined. A total of 35 motor units were recorded and each burst of superimposed vibration caused a momentary reduction in the firing rates and recruitment of additional units. Our data provide evidence that Ia input modulates the recruitment thresholds and firing rates of motor units providing more flexibility within the neuromuscular system to grade force at low levels of force production.

Vastus lateralis surface and single motor unit EMG following submaximal shortening and lengthening contractions

NARCIS (Netherlands)

Altenburg, T.M.; de Ruiter, C.J.; Verdijk, P.W.L.; van Mechelen, W.; de Haan, A.

2008-01-01

A single shortening contraction reduces the force capacity of muscle fibers, whereas force capacity is enhanced following lengthening. However, how motor unit recruitment and discharge rate (muscle activation) are adapted to such changes in force capacity during submaximal contractions remains

Extraosseous uptake of sup(99m)technetium methylene diphosphonate: Neuroblastoma or radiation therapy

Energy Technology Data Exchange (ETDEWEB)

Sty, J R; Kun, L; Casper, J; Babbitt, D P [Wisconsin Univ., Milwaukee (USA). Dept. of Radiology

1980-01-01

A child with a ganglioneuroblastoma and tumor uptake of sup(99m)technetium methylene diphosphonate (sup(99m)Tc-MDP) is presented. After surgical removal of an encapsulated tumor and radiation therapy, an interval bone scan demonstrated the same presurgical abnormality. Awareness of abnormal uptake of sup(99m)Tc-MDP in irradiated renal tissue prevents interpreting radiation nephritis as recurrent tumor.

Methylene Blue-Aided In Vivo Staining of Central Airways during Flexible Bronchoscopy

Directory of Open Access Journals (Sweden)

Sabine Zirlik

2012-01-01

Full Text Available Background. The early diagnosis of malignant and premalignant changes of the bronchial mucosa remains a major challenge during bronchoscopy. Intravital staining techniques are not new. Previous small case series suggested that analysis of the bronchial mucosal surface using chromoendoscopy allows a prediction between neoplastic and nonneoplastic lesions. Objectives. The aim of the present study was to evaluate chromobronchoscopy as a method to identify malignant and premalignant lesions in the central airways in a prospective manner. Methods. In 26 patients we performed chromoendoscopy with 0.1% methylene blue during ongoing flexible white light bronchoscopy. Circumscribed lesions in central airways were further analyzed by biopsies and histopathologic examination. Results. In the majority of cases neither flat nor polypoid lesions in the central airways were stained by methylene blue. In particular, exophytic growth of lung cancer did not show any specific pattern in chromobronchoscopy. However, a specific dye staining was detected in one case where exophytic growth of metastatic colorectal cancer was present in the right upper lobe. In two other cases, a circumscribed staining was noted in unsuspicious mucosa. But histology revealed inflammation only. Conclusions. In contrast to previous studies, the present findings clearly indicate that chromobronchoscopy is not useful for early detection of malignant or premalignant lesions of the central airways.

Decentralized Method for Load Sharing and Power Management in a Hybrid Single/Three-Phase-Islanded Microgrid Consisting of Hybrid Source PV/Battery Units

DEFF Research Database (Denmark)

Karimi, Yaser; Oraee, Hashem; Guerrero, Josep M.

2017-01-01

This paper proposes a new decentralized power management and load sharing method for a photovoltaic based, hybrid single/three-phase islanded microgrid consisting of various PV units, battery units and hybrid PV/battery units. The proposed method is not limited to the systems with separate PV...... in different load, PV generation and battery conditions is validated experimentally in a microgrid lab prototype consisted of one three-phase unit and two single-phase units....

Visible Light-Induced Degradation of Methylene Blue in the Presence of Photocatalytic ZnS and CdS Nanoparticles

Directory of Open Access Journals (Sweden)

Parisa Vaziri

2012-09-01

Full Text Available ZnS and CdS nanoparticles were prepared by a simple microwave irradiation method under mild conditions. The obtained nanoparticles were characterized by XRD, TEM and EDX. The results indicated that high purity of nanosized ZnS and CdS was successfully obtained with cubic and hexagonal crystalline structures, respectively. The band gap energies of ZnS and CdS nanoparticles were estimated using UV-visible absorption spectra to be about 4.22 and 2.64 eV, respectively. Photocatalytic degradation of methylene blue was carried out using physical mixtures of ZnS and CdS nanoparticles under a 500-W halogen lamp of visible light irradiation. The residual concentration of methylene blue solution was monitored using UV-visible absorption spectrometry. From the study of the variation in composition of ZnS:CdS, a composition of 1:4 (by weight was found to be very efficient for degradation of methylene blue. In this case the degradation efficiency of the photocatalyst nanoparticles after 6 h irradiation time was about 73% with a reaction rate of 3.61 × 10−3 min−1. Higher degradation efficiency and reaction rate were achieved by increasing the amount of photocatalyst and initial pH of the solution.

Graphene quantum dot synthesis using nanosecond laser pulses and its comparison to Methylene Blue

Science.gov (United States)

Kholikov, Khomidkhodza; Thomas, Zachary; Seyitliyev, Dovletgeldi; Smith, Skylar

A biocompatible photodynamic therapy agent that generates a high amount of singlet oxygen with high water dispersibility and excellent photostability is desirable. In this work, a graphene based biomaterial which is a promising alternative to a standard photosensitizers was produced. Methylene blue was used as a reference photosensitizer. Bacteria deactivation by methylene blue was shown to be inhibited inside human blood due to protein binding. Graphene quantum dots (GQD) were synthesized by irradiating benzene and nickel oxide mixture using nanosecond laser pulses. High resolution transmission electron microscopy (HR-TEM), scanning electron microscopy (SEM), atomic force microscopy (AFM), Fourier transform infrared (FTIR) spectroscopy, and nuclear magnetic resonance (NMR) were used for characterization of GQDs. Initial results show graphene quantum dots whose size less than 5 nm were successfully obtained. UV-VIS spectra shows absorption peak around 310 nm. The results of these studies can potentially be used to develop therapies for the eradication of pathogens in open wounds, burns, or skin cancers. New therapies for these conditions are particularly needed when antibiotic-resistant infections are present. NIH KBRIN.

Reagentless D-sorbitol biosensor based on D-sorbitol dehydrogenase immobilized in a sol-gel carbon nanotubes-poly(methylene green) composite.

Science.gov (United States)

Wang, Zhijie; Etienne, Mathieu; Urbanova, Veronika; Kohring, Gert-Wieland; Walcarius, Alain

2013-04-01

A reagentless D-sorbitol biosensor based on NAD-dependent D-sorbitol dehydrogenase (DSDH) immobilized in a sol-gel carbon nanotubes-poly(methylene green) composite has been developed. It was prepared by durably immobilizing the NAD(+) cofactor with DSDH in a sol-gel thin film on the surface of carbon nanotubes functionalized with poly(methylene green). This device enables selective determination of D-sorbitol at 0.2 V with a sensitivity of 8.7 μA mmol(-1) L cm(-2) and a detection limit of 0.11 mmol L(-1). Moreover, this biosensor has excellent operational stability upon continuous use in hydrodynamic conditions.

Is Cytox 3522 (10% methylene-bis-thiocyanate) a human skin sensitizer?

DEFF Research Database (Denmark)

Andersen, Klaus Ejner; Hamann, K

1983-01-01

Methylene-bis-thiocyanate is an antimicrobial agent in Cytox 3522 (American Cyanamid Corporation) and Nalco 206 (Nalco Chemical Company). Both are wide-spectrum industrial biocides. Cytox 3522 showed a strong sensitization potential in guineau pigs using the Guinea Pig Maximization Test and the O...... and the Open Epicutaneous Test procedures. In spite of this, human sensitization has not been reported. This may be explained by several factors such as limited exposure, low-use concentration and a lack of diagnostic patch tests in selected patients....

Removal of methylene blue from aqueous solution by chaff in batch mode

International Nuclear Information System (INIS)

Han Runping; Wang Yuanfeng; Han Pan; Shi Jie; Yang Jian; Lu Yongsen

2006-01-01

A new adsorbent system for removing methylene blue (MB) from aqueous solutions has been investigated. This new adsorbent is cereal chaff, an agriculture product in middle-west region in China. Variables of the system, including biosorption time, chaff dose, pH, salt concentration and initial MB concentration, were adopted to study their effects on MB removal. The results showed that as the dose of chaff increased, the percentage of MB sorption increased accordingly. There was no significant difference in the dye concentration remaining when the pH was increased from 4.0 to 11.0. The salt concentration has negative effect on MB removal. At the experimental range of MB concentration, the amount of MB adsorbed onto per unit mass of chaff (q e ) is direct ratio to MB initial concentration (c 0 ). The equilibrium data were analyzed using five equilibrium models, the Langmuir, the Freundlich, the Redlich-Peterson, the Koble-Corrigan and the Temkin isotherms. The results of non-linear regressive analysis are that the isotherms of Langmuir, Redlich-Peterson and Koble-Corrigan are better fit than the isotherms of Freundlich and Temkin at different temperatures according to the values of determined coefficients (R 2 ) and Chi-square statistic (χ 2 ). The maximum equilibrium capacities of chaff from Langmuir models are 20.3, 25.3 and 26.3 mg g -1 at 298, 318 and 333 K, respectively. Using the equilibrium concentration constants obtained at different temperatures, various thermodynamic parameters, such as ΔG 0 , ΔH 0 and ΔS 0 , have been calculated. The thermodynamics parameters of MB/chaff system indicate spontaneous and endothermic process. It was concluded that an increase in temperature results in a bigger MB loading per unit weight of the chaff

Extraosseous uptake of sup(99m)technetium methylene diphosphonate: Neuroblastoma or radiation therapy

International Nuclear Information System (INIS)

Sty, J.R.; Kun, L.; Casper, J.; Babbitt, D.P.

1980-01-01

A child with a ganglioneuroblastoma and tumor uptake of sup(99m)technetium methylene diphosphonate (sup(99m)Tc-MDP) is presented. After surgical removal of an encapsulated tumor and radiation therapy, an interval bone scan demonstrated the same presurgical abnormality. Awareness of abnormal uptake of sup(99m)Tc-MDP in irradiated renal tissue prevents interpreting radiation nephritis as recurrent tumor. (orig.) [de

Peritonitis: 10 years' experience in a single surgical unit.

Science.gov (United States)

Agarwal, Nitin; Saha, Sudipta; Srivastava, Anurag; Chumber, Sunil; Dhar, Anita; Garg, Sanket

2007-01-01

Peritonitis secondary to gut perforation is still one of the commonest surgical emergencies in India and is associated with high morbidity and mortality. The present study examines the aetiology and outcome of peritonitis cases operated on in our surgical unit, and compares our findings with those of previous studies performed between 1981 and 1991. A retrospective study of 260 peritonitis patients operated on in a single surgical unit from 1995 to 2006 was done and data involving clinical presentation, operative findings and post-operative course were studied and analysed. Causes of peritonitis were small bowel perforation (96 ileal, 17 jejunal), peptic perforation (45 duodenal, 16 gastric), appendicular perforation (36), primary peritonitis (8), and others (42). The incidence of major complications was 25% (burst-11%, leak-5%, intraabdominal abscess-5%, multi-organ failure-6.5%). The overall mortality was 10%. High mortality was observed in jejunal, gall bladder and liver abscess perforation cases (> 20%). Histopathological evaluation (143 specimens) revealed tuberculosis in 42 (mostly small bowel), malignancy in 8, and inflammation in the rest. Comparisons with a similar study carried out in the same unit and published in 1995 revealed similar demographic features and mortality, but a change in the most common cause (peptic ulcer perforation to small bowel perforation), and an increased performance of enterostomy compared with primary repair in small bowel perforation and a decrease in the leak rate (13% to 4%). Small bowel perforation is the commonest form of perforation and the mortality rate associated with peritonitis remains unchanged.

Trends in single women with malignancy of the uterine cervix in United States.

Science.gov (United States)

Machida, Hiroko; Blake, Erin A; Eckhardt, Sarah E; Takiuchi, Tsuyoshi; Grubbs, Brendan H; Mikami, Mikio; Roman, Lynda D; Matsuo, Koji

2018-03-01

To examine trends and characteristics of single women with malignancy of the uterine cervix. This is a retrospective observational study examining the United States population-based tumor registry (the Surveillance, Epidemiology, and End Results program). Time-specific trends in single marital status were examined in 3,294,208 women among 12 common female malignancies including 87,151 women with uterine cervical malignancy between 1973 and 2013. While the proportion of single women in the majority of malignancies increased during the study time, the proportion of single women with cervical malignancy significantly increased more than in other malignancies (29.3% in 2013 from 6.3% in 1973). There was a surge in the proportion of single women with cervical malignancy starting in the early 1990s, exhibiting the largest annual percentage rate change (APC) among all examined malignancies (1.8%; 95% confidence interval [CI]=1.6, 2.0; pwomen aged single women aged ≥40 years increased significantly during the time (APC, 2.7%; 95% CI=2.3, 3.2; psingle women with malignancy of the uterine cervix has significantly increased in the past 4 decades. This increase was most dramatic in single women aged ≥40 years. Improving screening strategies in single women aged ≥40 years may help reduce the incidence of this malignancy. Copyright © 2018. Asian Society of Gynecologic Oncology, Korean Society of Gynecologic Oncology

Single-unit-cell layer established Bi 2 WO 6 3D hierarchical architectures: Efficient adsorption, photocatalysis and dye-sensitized photoelectrochemical performance

Energy Technology Data Exchange (ETDEWEB)

Huang, Hongwei; Cao, Ranran; Yu, Shixin; Xu, Kang; Hao, Weichang; Wang, Yonggang; Dong, Fan; Zhang, Tierui; Zhang, Yihe

2017-12-01

Single-layer catalysis sparks huge interests and gains widespread attention owing to its high activity. Simultaneously, three-dimensional (3D) hierarchical structure can afford large surface area and abundant reactive sites, contributing to high efficiency. Herein, we report an absorbing single-unit-cell layer established Bi2WO6 3D hierarchical architecture fabricated by a sodium dodecyl benzene sulfonate (SDBS)-assisted assembled strategy. The DBS- long chains can adsorb on the (Bi2O2)2+ layers and hence impede stacking of the layers, resulting in the single-unit-cell layer. We also uncovered that SDS with a shorter chain is less effective than SDBS. Due to the sufficient exposure of surface O atoms, single-unit-cell layer 3D Bi2WO6 shows strong selectivity for adsorption on multiform organic dyes with different charges. Remarkably, the single-unit-cell layer 3D Bi2WO6 casts profoundly enhanced photodegradation activity and especially a superior photocatalytic H2 evolution rate, which is 14-fold increase in contrast to the bulk Bi2WO6. Systematic photoelectrochemical characterizations disclose that the substantially elevated carrier density and charge separation efficiency take responsibility for the strengthened photocatalytic performance. Additionally, the possibility of single-unit-cell layer 3D Bi2WO6 as dye-sensitized solar cells (DSSC) has also been attempted and it was manifested to be a promising dye-sensitized photoanode for oxygen evolution reaction (ORR). Our work not only furnish an insight into designing single-layer assembled 3D hierarchical architecture, but also offer a multi-functional material for environmental and energy applications.

Role of methylene spacer in the excitation energy transfer in europium 1- and 2- naphthylcarboxylates

Energy Technology Data Exchange (ETDEWEB)

Zhuravlev, K. [V.A. Kotelnikov Institute of Radioengineering and Electronics of RAS, 1 Vvedenskii sq., Fryazino Moscow reg. 141190 (Russian Federation); Tsaryuk, V., E-mail: vit225@ire216.msk.s [V.A. Kotelnikov Institute of Radioengineering and Electronics of RAS, 1 Vvedenskii sq., Fryazino Moscow reg. 141190 (Russian Federation); Kudryashova, V.; Pekareva, I. [V.A. Kotelnikov Institute of Radioengineering and Electronics of RAS, 1 Vvedenskii sq., Fryazino Moscow reg. 141190 (Russian Federation); Sokolnicki, J. [Faculty of Chemistry, University of WrocLaw, 14 F. Joliot-Curie str., WrocLaw 50-383 (Poland); Yakovlev, Yu. [V.A. Kotelnikov Institute of Radioengineering and Electronics of RAS, 1 Vvedenskii sq., Fryazino Moscow reg. 141190 (Russian Federation)

2010-08-15

A series of compounds Ln(RCOO){sub 3}.Phen (Ln=Eu, Gd, Tb; RCOO{sup -}-1- and 2-naphthoate, 1- and 2-naphthylacetate, 1- and 2-naphthoxyacetate anions, Phen-1,10-phenanthroline) was investigated by methods of optical spectroscopy. Compounds of composition Ln(RCOO){sub 3}.nH{sub 2}O with the same carboxylate ligands are also considered. Results of studies of the effects of methylene spacer decoupling the {pi}-{pi}- or p-{pi}-conjugation in the naphthylcarboxylate ligand on the structure of Eu{sup 3+} coordination centre, on the lifetime of {sup 5}D{sub 0} (Eu{sup 3+}) state, and on processes of the excitation energy transfer to Eu{sup 3+} or Tb{sup 3+} ions are presented. Introduction of the methylene bridge in the ligand weakens the influence of the steric hindrances in forming of a crystal lattice and results in lowering the distortion of the Eu{sup 3+} luminescence centre, and in elongation of the observed {sup 5}D{sub 0} lifetime {tau}{sub obs}. The latter is caused by decrease in contribution of the radiative processes rate 1/{tau}{sub r}. This is confirmed by the correlation between the lifetimes {tau}{sub obs} and the quantities '{tau}{sub r}.const' inversely proportional to the total integral intensities of Eu(RCOO){sub 3}.Phen luminescence spectra. The methylene spacer performs a role of regulator of sensitization of the Ln{sup 3+} luminescence efficiency by means of an influence on mutual location of lowest triplet states of the ligands, the ligand-metal charge transfer (LMCT) states, and the emitting states of Ln{sup 3+} ions. The lowest triplet state in lanthanide naphthylcarboxylate adducts with Phen is related to carboxylate anion. A presence of the methylene spacer in naphthylcarboxylate ligand increases the triplet state energy. At the same time, the energy of 'carboxylic group-Eu{sup 3+} ion' charge transfer states falls, which can promote the degradation of excitation energy. In naphthylcarboxylates investigated a range of the

The antimalarial activities of methylene blue and the 1,4-naphthoquinone 3-[4-(trifluoromethyl)benzyl]-menadione are not due to inhibition of the mitochondrial electron transport chain.

Science.gov (United States)

Ehrhardt, Katharina; Davioud-Charvet, Elisabeth; Ke, Hangjun; Vaidya, Akhil B; Lanzer, Michael; Deponte, Marcel

2013-05-01

Methylene blue and a series of recently developed 1,4-naphthoquinones, including 3-[4-(substituted)benzyl]-menadiones, are potent antimalarial agents in vitro and in vivo. The activity of these structurally diverse compounds against the human malaria parasite Plasmodium falciparum might involve their peculiar redox properties. According to the current theory, redox-active methylene blue and 3-[4-(trifluoromethyl)benzyl]-menadione are "subversive substrates." These agents are thought to shuttle electrons from reduced flavoproteins to acceptors such as hemoglobin-associated or free Fe(III)-protoporphyrin IX. The reduction of Fe(III)-protoporphyrin IX could subsequently prevent essential hemoglobin digestion and heme detoxification in the parasite. Alternatively, owing to their structures and redox properties, methylene blue and 1,4-naphthoquinones might also affect the mitochondrial electron transport chain. Here, we tested the latter hypothesis using an established system of transgenic P. falciparum cell lines and the antimalarial agents atovaquone and chloroquine as controls. In contrast to atovaquone, methylene blue and 3-[4-(trifluoromethyl)benzyl]-menadione do not inhibit the mitochondrial electron transport chain. A systematic comparison of the morphologies of drug-treated parasites furthermore suggests that the three drugs do not share a mechanism of action. Our findings support the idea that methylene blue and 3-[4-(trifluoromethyl)benzyl]-menadione exert their antimalarial activity as redox-active subversive substrates.

Liver metastases of breast carcinoma detected on /sup 99m/Tc-methylene diphosphonate bone scan

International Nuclear Information System (INIS)

Baumert, J.E.; Lantieri, R.L.; Horning, S.; McDougall, I.R.

1980-01-01

The accumulation of bone-seeking radiopharmaceuticals has been reported in liver metastases from colon carcinoma and oat cell carcinoma of the lung. Two patients with breast carcinoma in whom hepatic metastases were visualized on /sup 99m/Tc-methylene diphosphonate bone images are described. This has not been previously reported

Post-operative outcomes following the excision of dorsal wrist ganglions with/without the use of Methylene Blue

Directory of Open Access Journals (Sweden)

Suleyman Tas

2016-04-01

Conclusions: The recurrence of cysts is rare after complete excision, particularly when rupture is prevented. Methylene blue injection is useful for ensuring complete excision and, therefore, to prevent recurrence. [Hand Microsurg 2016; 5(1.000: 1-6

SOURCE CHARACTERIZATION AND CONTROL TECHNOLOGY ASSESSMENT OF METHYLENE CHLORIDE EMISSIONS FROM EASTMAN KODAK COMPANY, ROCHESTER, NY

Science.gov (United States)

The report gives results of an assessment of potential control technologies for methylene chloride (also known as dichloromethane or DCM) emission sources at Eastman Kodak Company's Kodak Park facility in Rochester, NY. DCM is a solvent used by Kodak in the manufacture of cellulo...

Sol–gel synthesis of SnO2–MgO nanoparticles and their photocatalytic activity towards methylene blue degradation

International Nuclear Information System (INIS)

Bayal, Nisha; Jeevanandam, P.

2013-01-01

Graphical abstract: - Highlights: • A simple sol–gel method for the synthesis of SnO 2 –MgO nanoparticles is reported. • Band gap of SnO 2 can be tuned by varying the magnesium content in SnO 2 –MgO. • SnO 2 –MgO shows good photocatalytic activity towards degradation of methylene blue. - Abstract: SnO 2 –MgO mixed metal oxide nanoparticles were prepared by a simple sol–gel method. The nanoparticles were characterized by power X-ray diffraction, scanning electron microscopy coupled with energy dispersive X-ray analysis, transmission electron microscopy and UV–vis diffuse reflectance spectroscopy. The XRD results indicate the formation of mixed metal oxide nanoparticles and also a decrease of SnO 2 crystallite size in the mixed metal oxide nanoparticles with increasing magnesium oxide content. The reflectance spectroscopy results show a blue shift of the band gap of SnO 2 in the mixed metal oxide nanoparticles. The photocatalytic activity of the SnO 2 –MgO nanoparticles was tested using the photodegradation of aqueous methylene blue in the presence of sunlight. The results indicate that the mixed metal oxide nanoparticles possess higher efficiency for the photodegradation of methylene blue compared to pure SnO 2 nanoparticles

Synthesis of /sup 14/C-labeled felbamate from phenylacetic-(methylene-/sup 14/C) acid

Energy Technology Data Exchange (ETDEWEB)

Choi, Y.M.; Kucharczyk, N.; Sofia, R.D.

1986-05-01

A synthetic procedure for the preparation of 2-phenyl-1,3-propanediol-2-/sup 14/C dicarbamate, starting with phenylacetic-(methylene-/sup 14/C) acid was developed. The procedure from phenylacetic acid to 2-phenyl-1,3-propanediol dicarbamate has four steps via phenylmalonic acid and 2-phenyl-1,3-propanediol. The overall yield of all four steps was 28%.

Wireless multi-channel single unit recording in freely moving and vocalizing primates.

Science.gov (United States)

Roy, Sabyasachi; Wang, Xiaoqin

2012-01-15

The ability to record well-isolated action potentials from individual neurons in naturally behaving animals is crucial for understanding neural mechanisms underlying natural behaviors. Traditional neurophysiology techniques, however, require the animal to be restrained which often restricts natural behavior. An example is the common marmoset (Callithrix jacchus), a highly vocal New World primate species, used in our laboratory to study the neural correlates of vocal production and sensory feedback. When restrained by traditional neurophysiological techniques marmoset vocal behavior is severely inhibited. Tethered recording systems, while proven effective in rodents pose limitations in arboreal animals such as the marmoset that typically roam in a three-dimensional environment. To overcome these obstacles, we have developed a wireless neural recording technique that is capable of collecting single-unit data from chronically implanted multi-electrodes in freely moving marmosets. A lightweight, low power and low noise wireless transmitter (headstage) is attached to a multi-electrode array placed in the premotor cortex of the marmoset. The wireless headstage is capable of transmitting 15 channels of neural data with signal-to-noise ratio (SNR) comparable to a tethered system. To minimize radio-frequency (RF) and electro-magnetic interference (EMI), the experiments were conducted within a custom designed RF/EMI and acoustically shielded chamber. The individual electrodes of the multi-electrode array were periodically advanced to densely sample the cortical layers. We recorded single-unit data over a period of several months from the frontal cortex of two marmosets. These recordings demonstrate the feasibility of using our wireless recording method to study single neuron activity in freely roaming primates. Copyright © 2011 Elsevier B.V. All rights reserved.

Chronic neural probe for simultaneous recording of single-unit, multi-unit, and local field potential activity from multiple brain sites

Science.gov (United States)

Pothof, F.; Bonini, L.; Lanzilotto, M.; Livi, A.; Fogassi, L.; Orban, G. A.; Paul, O.; Ruther, P.

2016-08-01

Objective. Drug resistant focal epilepsy can be treated by resecting the epileptic focus requiring a precise focus localisation using stereoelectroencephalography (SEEG) probes. As commercial SEEG probes offer only a limited spatial resolution, probes of higher channel count and design freedom enabling the incorporation of macro and microelectrodes would help increasing spatial resolution and thus open new perspectives for investigating mechanisms underlying focal epilepsy and its treatment. This work describes a new fabrication process for SEEG probes with materials and dimensions similar to clinical probes enabling recording single neuron activity at high spatial resolution. Approach. Polyimide is used as a biocompatible flexible substrate into which platinum electrodes and leads are integrated with a minimal feature size of 5 μm. The polyimide foils are rolled into the cylindrical probe shape at a diameter of 0.8 mm. The resulting probe features match those of clinically approved devices. Tests in saline solution confirmed the probe stability and functionality. Probes were implanted into the brain of one monkey (Macaca mulatta), trained to perform different motor tasks. Suitable configurations including up to 128 electrode sites allow the recording of task-related neuronal signals. Main results. Probes with 32 and 64 electrode sites were implanted in the posterior parietal cortex. Local field potentials and multi-unit activity were recorded as early as one hour after implantation. Stable single-unit activity was achieved for up to 26 days after implantation of a 64-channel probe. All recorded signals showed modulation during task execution. Significance. With the novel probes it is possible to record stable biologically relevant data over a time span exceeding the usual time needed for epileptic focus localisation in human patients. This is the first time that single units are recorded along cylindrical polyimide probes chronically implanted 22 mm deep into the

Response of cat cerebellar vermis induced by sound. I. Influence of drugs on responses of single units.

Science.gov (United States)

Jastreboff, P J; Tarnecki, R

1975-01-01

Experiments were done on the cats under Chloralose and/or Nembutal anesthesia. A click was used as a standard acoustic stimulus. The type of responses of single units from cerebellar vermis lobuli V-VII were analyzed. At least four different types of single unit reactions were observed and one of these - oscillatory - was produced by the presence of Flaxedil simultaneously with Chloralose. The system that controls the activity of the middle-ear-muscles can be suspected as the source of the oscillatory pattern of the cerebellar response. Latencies were found to be constant, independent of anesthesia, but it was necessary to have a low level of Nembutal anesthesia because of the overriding inhibitory influence of Nembutal.

Green synthesis of silver nanoparticle-reduced graphene oxide using Psidium guajava and its application in SERS for the detection of methylene blue

Science.gov (United States)

Chettri, Prajwal; Vendamani, V. S.; Tripathi, Ajay; Singh, Manish Kumar; Pathak, Anand P.; Tiwari, Archana

2017-06-01

Here we present the synthesis of reduced graphene oxide and silver nanoparticle-reduced graphene oxide composites using aqueous extract of dry leaves of Psidium guajava by one pot reflux method. Psidium guajava extract simultaneously reduces silver nitrate and graphene oxide in the reaction mixture which is confirmed by various spectroscopic techniques. Variable concentrations of silver nitrate solution are used to obtain reduced graphene oxide with different dosage of silver nanoparticles and the resultant composites are examined using surface enhanced Raman scattering measurements. Considering methylene blue as a probe molecule, it is found that the surface enhanced Raman scattering activity increases with the increase in the dose of silver nanoparticles. Our as-synthesised silver nanoparticle-reduced graphene oxide composite shows remarkable performance in detecting methylene blue with concentration as low as 10-8 M for which the enhancement factor is 4.6 × 105. In addition, we report that the reduced graphene oxide quenches the photoluminescence of methylene blue more efficiently than silver nanoparticle-reduced graphene oxide composite. The charge transfer states have been extracted which are mainly responsible for the quenching processes.

Extraosseous uptake of /sup 99/sup(m)technetium methylene diphosphonate. Neuroblastoma or radiation therapy

Energy Technology Data Exchange (ETDEWEB)

Sty, J R; Kun, L; Casper, J; Babbitt, D P

1980-01-01

A child with a ganglioneuroblastoma and tumor uptake of /sup 99/sup(m)technetium methylene diphosphate (/sup 99/sup(m)Tc-MDP) is presented. After surgical removal of an encapsulated tumor and radiation therapy, an interval bone scan demonstrated the same presurgical abnormality. Awareness of abnormal uptake of /sup 99/sup(m)Tc-MDP in irradiated renal tissue prevents interpreting radiation nephritis as recurrent tumor.

Increased uptake of technetium-99m methylene diphosphonate in muscles in the course of polymyositis

International Nuclear Information System (INIS)

Niemir, Z.; Oleksa, R.; Czepczynski, R.; Sowinski, J.

2005-01-01

A case of a woman aged 46 years with signs of rhabdomyolysis and acute renal failure is presented. Coxsackie serum test was positive. Increased uptake of Technetium-99m methylene diphosphonate ( 99mT c-MDP) by muscles of thighs and calves was observed. After 1 year no increased accumulation of radiotracer in the muscles was found

Adsorption of methylene blue on raw and MTZ/imogolite hybrid surfaces: Effect of concentration and calorimetric investigation

Energy Technology Data Exchange (ETDEWEB)

Guerra, Denis L., E-mail: dlguerra@pq.cnpq.br [Universidade Federal de Mato Grosso, DRM, UFMT, Mato Grosso 78060 900 (Brazil); Batista, Adriano C. [Universidade Estadual do Norte Fluminense, UENF, Rio de Janeiro 28013 02 (Brazil); Viana, Rubia R. [Universidade Federal de Mato Grosso, DRM, UFMT, Mato Grosso 78060 900 (Brazil); Airoldi, Claudio [Chemistry Institute, State University of Campinas, PO Box 6154, 13084-971 Campinas, Sao Paulo (Brazil)

2010-11-15

The synthetic imogolite sample was used for organofunctionalization process with 2-mercaptothiazoline (MTZ). The compound 2-mercaptothiazoline was anchored onto imogolite surface by heterogeneous route. Due to the increment of basic centers attached to the pendant chains the dye adsorption capability of the final chelating material, was found to be higher than is precursor. The ability of these materials to remove methylene blue from aqueous solution was followed by a series of adsorption isotherms at room temperature and pH 4.0. The maximum number of moles adsorbed was determined to be 40.32 x 10{sup -2} and 65.13 x 10{sup -2} mmol g{sup -1} for IMO and IMO{sub MTZ}, respectively. The energetic effects caused by dye cations adsorption were determined through calorimetric titrations. Thermodynamics indicated the existence of favorable conditions for such methylene blue-nitrogen and sulfur interactions.

Reliability modelling for wear out failure period of a single unit system

OpenAIRE

Arekar, Kirti; Ailawadi, Satish; Jain, Rinku

2012-01-01

The present paper deals with two time-shifted density models for wear out failure period of a single unit system. The study, considered the time-shifted Gamma and Normal distributions. Wear out failures occur as a result of deterioration processes or mechanical wear and its probability of occurrence increases with time. A failure rate as a function of time deceases in an early failure period and it increases in wear out period. Failure rates for time shifted distributions and expression for m...

Decentralized method for load sharing and power management in a hybrid single/three-phase islanded microgrid consisting of hybrid source PV/battery units

DEFF Research Database (Denmark)

Karimi, Yaser; Guerrero, Josep M.; Oraee, Hashem

2016-01-01

This paper proposes a new decentralized power management and load sharing method for a photovoltaic based, hybrid single/three-phase islanded microgrid consisting of various PV units, battery units and hybrid PV/battery units. The proposed method takes into account the available PV power...... and battery conditions of the units to share the load among them and power flow among different phases is performed automatically through three-phase units. Modified active power-frequency droop functions are used according to operating states of each unit and the frequency level is used as trigger...... for switching between the states. Efficacy of the proposed method in different load, PV generation and battery conditions is validated experimentally in a microgrid lab prototype consisted of one three-phase unit and two single-phase units....

Production and postharvest quality maintenance of single unit and bunching broccoli in Virginia

OpenAIRE

Jett, Lewis W.

1990-01-01

Broccoli (Brassica oleracea L. var. italica) has become an increasingly popular vegetable with American consumers. Much of the attractiveness of fresh broccoli is derived from this vegetable's high nutrition and excellent organoleptic properties. In a consumer response survey, Virginia Master Gardeners indicated a preference for broccoli that has less stalk and more florets by weight. The objectives of this research were to produce single unit broccoli, and to examine vac...

Homogeneous photosensitized degradation of pharmaceuticals by using red light LED as light source and methylene blue as photosensitizer

NARCIS (Netherlands)

Ye, Y.; Bruning, H.; Yntema, D.; Mayer, M.; Rijnaarts, H.

2017-01-01

Research on employing advanced oxidation processes (AOPs) for pharmaceuticals removal is gaining interests. However, detrimental effects of background water constituents in complex water matrices are limiting their implementation. In this study, we report red light induced methylene blue

MO-G-18C-07: Improving T2 Determination and Quantification of Lipid Methylene Protons in Proton Magnetic Resonance Spectroscopy at 3 T

Energy Technology Data Exchange (ETDEWEB)

Breitkreutz, D. [of Oncology, University of Alberta, Edmonton, AB (Canada); Fallone, B. G.; Yahya, A. [of Oncology, University of Alberta, Edmonton, AB (Canada); Department of Medical Physics, Cross Cancer Institute, Edmonton, AB (Canada)

2014-06-15

Purpose: To improve proton magnetic resonance spectroscopy (MRS) transverse relaxation (T{sub 2}) determination and quantification of lipid methylene chain (1.3 ppm) protons by rewinding their J-coupling evolution. Methods: MRS experiments were performed on four lipid phantoms, namely, almond, corn, sunflower and oleic acid, using a 3 T Philips MRI scanner with a transmit/receive birdcage head coil. Two PRESS (Point RESolved Spectroscopy) pulse sequences were used. The first PRESS sequence employed standard bandwidth (BW) (∼550 Hz) RF (radiofrequency) refocussing pulses, while the second used refocussing pulses of narrow BW (∼50 Hz) designed to rewind J-coupling evolution of the methylene protons in the voxel of interest. Signal was acquired with each sequence from a 5×5×5 mm{sup 3} voxel, with a repetition time (TR) of 3000 ms, and with echo times (TE) of 100 to 200 ms in steps of 20 ms. 2048 sample points were measured with a 2000 Hz sampling bandwidth. Additionally, 30 mm outer volume suppression slabs were used to suppress signal outside the voxel of interest. The frequency of the RF pulses was set to that of the methylene resonance. Methylene peak areas were calculated and fitted in MATLAB to a monexponentially decaying function of the form M{sub 0}exp(-TE/T{sub 2}), where M{sub 0} is the extrapolated area when TE = 0 ms and yields a measure of concentration. Results: The determined values of M{sub 0} and T{sub 2} increased for all fatty acids when using the PRESS sequence with narrow BW refocussing pulses. M{sub 0} and T{sub 2} values increased by an average amount (over all the phantoms) of 31% and 14%, respectively. Conclusion: This investigation has demonstrated that J-coupling interactions of lipid methylene protons causes non-negligible signal losses which, if not accounted for, Result in underestimations of their levels and T{sub 2} values when performing MRS measurements. Funded by the Natural Sciences and Engineering Research Council of Canada

Methylene-tetrahydrofolate reductase contributes to allergic airway disease.

Directory of Open Access Journals (Sweden)

Kenneth R Eyring

Full Text Available Environmental exposures strongly influence the development and progression of asthma. We have previously demonstrated that mice exposed to a diet enriched with methyl donors during vulnerable periods of fetal development can enhance the heritable risk of allergic airway disease through epigenetic changes. There is conflicting evidence on the role of folate (one of the primary methyl donors in modifying allergic airway disease.We hypothesized that blocking folate metabolism through the loss of methylene-tetrahydrofolate reductase (Mthfr activity would reduce the allergic airway disease phenotype through epigenetic mechanisms.Allergic airway disease was induced in C57BL/6 and C57BL/6Mthfr-/- mice through house dust mite (HDM exposure. Airway inflammation and airway hyperresponsiveness (AHR were measured between the two groups. Gene expression and methylation profiles were generated for whole lung tissue. Disease and molecular outcomes were evaluated in C57BL/6 and C57BL/6Mthfr-/- mice supplemented with betaine.Loss of Mthfr alters single carbon metabolite levels in the lung and serum including elevated homocysteine and cystathionine and reduced methionine. HDM-treated C57BL/6Mthfr-/- mice demonstrated significantly less airway hyperreactivity (AHR compared to HDM-treated C57BL/6 mice. Furthermore, HDM-treated C57BL/6Mthfr-/- mice compared to HDM-treated C57BL/6 mice have reduced whole lung lavage (WLL cellularity, eosinophilia, and Il-4/Il-5 cytokine concentrations. Betaine supplementation reversed parts of the HDM-induced allergic airway disease that are modified by Mthfr loss. 737 genes are differentially expressed and 146 regions are differentially methylated in lung tissue from HDM-treated C57BL/6Mthfr-/- mice and HDM-treated C57BL/6 mice. Additionally, analysis of methylation/expression relationships identified 503 significant correlations.Collectively, these findings indicate that the loss of folate as a methyl donor is a modifier of

Unit-cell design for two-dimensional phase-field simulation of microstructure evolution in single-crystal Ni-based superalloys during solidification

Directory of Open Access Journals (Sweden)

Dongjia Cao

2017-12-01

Full Text Available Phase-field simulation serves as an effective tool for quantitative characterization of microstructure evolution in single-crystal Ni-based superalloys during solidification nowadays. The classic unit cell is either limited to γ dendrites along crystal orientation or too ideal to cover complex morphologies for γ dendrites. An attempt to design the unit cell for two-dimensional (2-D phase-field simulations of microstructure evolution in single-crystal Ni-based superalloys during solidification was thus performed by using the MICRESS (MICRostructure Evolution Simulation Software in the framework of the multi-phase-field (MPF model, and demonstrated in a commercial TMS-113 superalloy. The coupling to CALPHAD (CALculation of PHAse Diagram thermodynamic database was realized via the TQ interface and the experimental diffusion coefficients were utilized in the simulation. Firstly, the classic unit cell with a single γ dendrite along crystal orientation was employed for the phase-field simulation in order to reproduce the microstructure features. Then, such simple unit cell was extended into the cases with two other different crystal orientations, i.e., and . Thirdly, for crystal orientations, the effect of γ dendritic orientations and unit cell sizes on microstructure and microsegregation was comprehensively studied, from which a new unit cell with multiple γ dendrites was proposed. The phase-field simulation with the newly proposed unit cell was further performed in the TMS-113 superalloy, and the microstructure features including the competitive growth of γ dendrites, microsegregation of different solutes and distribution of γ′ grains, can be nicely reproduced.

[Loading and strength of single- and multi-unit fixed dental prostheses. 1. Retention and resistance

NARCIS (Netherlands)

Baat, C. de; Witter, D.J.; Meijers, C.C.A.J.; Vergoossen, E.L.; Creugers, N.H.J.

2014-01-01

The degree to which single- and multi-unit fixed dental prostheses are able to withstand loading forces is dependent, among other things, on the quality of their retention and resistance. The quality of the retention and resistance of the configuration of an abutment tooth prepared for a metal and

Wiring of heme enzymes by methylene-blue labeled dendrimers

DEFF Research Database (Denmark)

Álvarez-Martos, Isabel; Shahdost-fard, Faezeh; Ferapontova, Elena

2017-01-01

Redox-modified branched 3D dendrimeric nanostructures may be considered as perspective wires for electrical connection between redox enzymes and electrodes. Here, we studied electron transfer (ET) reactions and bioelectrocatalysis of heme-containing horseradish peroxidase (HRP) and heme- and moli......Redox-modified branched 3D dendrimeric nanostructures may be considered as perspective wires for electrical connection between redox enzymes and electrodes. Here, we studied electron transfer (ET) reactions and bioelectrocatalysis of heme-containing horseradish peroxidase (HRP) and heme......- and molibdopterin-containing sulfite oxidase (SOx), wired to gold by the methylene blue (MB)-labeled polyamidoamine (PAMAM) dendrimers. The enzymes’ electrochemical transformation and bioelectrocatalytic function could be followed at both unlabeled and MB-labeled dendrimer-modified electrodes with the formal redox......, optimization of bioelectrocatalysis of complex intermembrane and, possibly, membrane enzymes....

Performance Evaluation of Hap-Free Paint Strippers vs. Methylene-Chloride-Based Strippers for Removing Army Chemical Agent Resistant Coatings (CARC)

National Research Council Canada - National Science Library

Kelley, John; Considine, Thomas

2006-01-01

...). The purpose of this effort is to investigate HAP-free alternative chemical paint strippers as potential replacements for the methylene-chloride- based chemical strippers currently used in both processes...

A selective C-H insertion/olefination protocol for the synthesis of α-methylene-γ-butyrolactone natural products.

Science.gov (United States)

Lloyd, Matthew G; D'Acunto, Mariantonietta; Taylor, Richard J K; Unsworth, William P

2016-02-07

A regio- and stereoselective one-pot C-H insertion/olefination protocol has been developed for the late stage installation of α-methylene-γ-butyrolactones into conformationally restricted cyclohexanol-derivatives. The method has been successfully applied in the total synthesis of eudesmanolide natural product frameworks, including α-cyclocostunolide.

Methylene Blue Dye-Induced Skin Necrosis in Immediate Breast Reconstruction: Evaluation and Management

Directory of Open Access Journals (Sweden)

Ji Hwan Lee

2014-05-01

Full Text Available Background For early breast cancer patients, skin-sparing mastectomy or nipple-sparing mastectomy with sentinel lymph node biopsy has become the mainstream treatment for immediate breast reconstruction in possible cases. However, a few cases of skin necrosis caused by methylene blue dye (MBD used for sentinel lymph node localization have been reported. Methods Immediate breast reconstruction using a silicone implant was performed on 35 breasts of 34 patients after mastectomy. For sentinel lymph node localization, 1% MBD (3 mL was injected into the subareolar area. The operation site was inspected in the postoperative evaluation. Results Six cases of immediate breast reconstruction using implants were complicated by methylene blue dye. One case of local infection was improved by conservative treatment. In two cases, partial necrosis and wound dehiscence of the incision areas were observed; thus, debridement and closure were performed. Of the three cases of wide skin necrosis, two cases underwent removal of the dead tissue and implants, followed by primary closure. In the other case, the breast implant was salvaged using latissimus dorsi musculocutaneous flap reconstruction. Conclusions The complications were caused by MBD toxicity, which aggravated blood disturbance and skin tension after implant insertion. When planning immediate breast reconstruction using silicone implants, complications of MBD should be discussed in detail prior to surgery, and appropriate management in the event of complications is required.

Photoinactivation effect of eosin methylene blue and chlorophyllin sodium-copper against Staphylococcus aureus and Escherichia coli.

Science.gov (United States)

Caires, Cynthia S A; Leal, Cassia R B; Ramos, Carlos A N; Bogo, Danielle; Lima, Alessandra R; Arruda, Eduardo J; Oliveira, Samuel L; Caires, Anderson R L; Nascimento, Valter A

2017-07-01

The use of eosin methylene blue according to Giemsa as photosensitizer is presented for the first time in this paper. The present study evaluated the potential application of chlorophyllin sodium copper salt (CuChlNa) and eosin methylene blue according to Giemsa (EMB) as antimicrobial photosensitizers (aPS) for photodynamic inactivation (PDI) of Staphylococcus aureus (gram-positive) and Escherichia coli (gram-negative) bacteria. The experiments were performed using S. aureus stain ATCC 25923 and E. coli ATCC 25922 in which five aPS concentrations (0.0, 1.0, 2.5, 5.0, 10.0, and 20.0 μM for S. aureus and 0.0, 5.0, 10.0, 20.0, 40.0, and 50.0 μM for E. coli) were prepared and added in 2 mL of a saline solution containing the bacterial inoculum. After aPS incubation, the samples were divided into two groups, one kept in the dark and another submitted to the illumination. Then, the bacterial inactivation was determined 18 h after the incubation at 37 °C by counting the colony-forming units (CFU). The results revealed that both EMB and CuChlNa can be used as aPS for the photoinactivation of S. aureus, while only EMB was able to photoinactivate E. coli. Nevertheless, a more complex experimental setup was needed for photoinactivation of E. coli. The data showed that EMB and CuChlNa presented similar photoinactivation effects on S. aureus, in which bacterial growth was completely inhibited at photosensitizer (PS) concentrations over 5 μM, when samples were previously incubated for 30 min and irradiated by a light dose of 30 J cm -2 as a result of an illumination of 1 h at 8.3 mW cm -2 by using a red light at 625 nm with a 1 cm beam diameter and output power of 6.5 mW. In the case of E. coli, bacterial growth was completely inhibited only when combining a PS incubation period of 120 min with concentrations over 20 μM.

Selective recruitment of single motor units in human flexor digitorum superficialis muscle during flexion of individual fingers.

Science.gov (United States)

Butler, T J; Kilbreath, S L; Gorman, R B; Gandevia, S C

2005-08-15

Flexor digitorum superficialis (FDS) is an extrinsic multi-tendoned muscle which flexes the proximal interphalangeal joints of the four fingers. It comprises four digital components, each with a tendon that inserts onto its corresponding finger. To determine the degree to which these digital components can be selectively recruited by volition, we recorded the activity of a single motor unit in one component via an intramuscular electrode while the subject isometrically flexed each of the remaining fingers, one at a time. The finger on which the unit principally acted was defined as the 'test finger' and that which flexed isometrically was the 'active' finger. Activity in 79 units was recorded. Isometric finger flexion forces of 50% maximum voluntary contraction (MVC) activated less than 50% of single units in components of FDS acting on fingers that were not voluntarily flexed. With two exceptions, the median recruitment threshold for all active-test finger combinations involving the index, middle, ring and little finger test units was between 49 and 60% MVC (60% MVC being the value assigned to those not recruited). The exceptions were flexion of the little finger while recording from ring finger units (median: 40% MVC), and vice versa (median: 2% MVC). For all active-test finger combinations, only 35/181 units were activated when the active finger flexed at less than 20% MVC, and the fingers were adjacent for 28 of these. Functionally, to recruit FDS units during grasping and lifting, relatively heavy objects were required, although systematic variation occurred with the width of the object. In conclusion, FDS components can be selectively activated by volition and this may be especially important for grasping at high forces with one or more fingers.

Methylene blue degradation by NaTaO3 sol-gel doped with Sm and La

International Nuclear Information System (INIS)

Torres-Martinez, Leticia M.; Cruz-Lopez, Arquimedes; Juarez-Ramirez, Isaias; Meza-de la Rosa, Ma. Elena

2009-01-01

In this work, NaTaO 3 compounds doped with 1 M% of La and Sm, were prepared by the sol-gel (SG) method and solid state (SS) reaction; and tested as photocatalysts on the degradation of methylene blue (MB) under UV light. The structural characterization by X-ray powder diffraction revealed that the crystallization of the NaTaO 3 phase prepared by the sol-gel method started at 600 deg. C, reaching maximum crystallization at 800 deg. C. It was determined that the presence of Sm and La retard the crystallization of the NaTaO 3 phase. On the other hand, the compounds synthesized in this work showed particle sizes in the nanometric scale, as it was observed by scanning electron microscopy (SEM). The specific surface area of the compounds synthesized by the sol-gel method, showed values 4 times higher than those obtained by the solid state reaction, favoring their functional and photocatalytic performance in the methylene blue degradation. In addition, the best photocatalytic performance was shown by the NaTaO 3 doped with Sm and heated at 600 deg. C, having a half-life time of 65 min.

Structural characteristics of mixed oxides MOx/SiO2 affecting photocatalytic decomposition of methylene blue

International Nuclear Information System (INIS)

Gun’ko, V.M.; Blitz, J.P.; Bandaranayake, B.; Pakhlov, E.M.; Zarko, V.I.; Sulym, I.Ya.; Kulyk, K.S.; Galaburda, M.V.; Bogatyrev, V.M.; Oranska, O.I.; Borysenko, M.V.; Leboda, R.; Skubiszewska-Zięba, J.; Janush, W.

2012-01-01

A series of photocatalysts based on silica (nanoparticulate) supported titania, ceria, and ceria/zirconia were synthesized and characterized by a variety of techniques including surface area measurements, X-ray diffraction, Fourier transform infrared spectroscopy, zeta potential, surface charge density, and photocatalytic behavior toward methylene blue decomposition. Thermal treatment at 600 °C increases the anatase content of the titania based catalysts detected by XRD. Changes in the infrared spectra before and after thermal treatment indicate that at low temperature there are more ≡Si-O-Ti≡ bonds than at high temperature. As these bonds break upon heating the SiO 2 and TiO 2 separate, allowing the TiO 2 anatase phase to form. This results in an increased catalytic activity for the thermally treated samples. Nearly all titania based samples exhibit a negative surface charge density at pH 7 (initial pH of photocatalytic studies) which aids adsorption of methylene blue. The crystallinity of ceria and ceria/zirconia based catalysts are in some cases limited, and in others non-existent. Even though the energy band gap (E g ) can be lower for these catalysts than for the titania based catalysts, their photocatalytic properties are inferior.

Methylene blue as a lignin surrogate in manganese peroxidase reaction systems.

Science.gov (United States)

Goby, Jeffrey D; Penner, Michael H; Lajoie, Curtis A; Kelly, Christine J

2017-11-15

Manganese peroxidase (MnP) is associated with lignin degradation and is thus relevant to lignocellulosic-utilization technologies. Technological applications require reaction mixture optimization. A surrogate substrate can facilitate this if its susceptibility to degradation is easily monitored and mirrors that of lignin. The dye methylene blue (MB) was evaluated in these respects as a surrogate substrate by testing its reactivity in reaction mixtures containing relevant redox mediators (dicarboxylic acids, fatty acids). Relative rates of MB degradation were compared to available literature reports of lignin degradation under similar conditions, and suggest that MB can be a useful lignin surrogate in MnP systems. Copyright © 2017 Elsevier Inc. All rights reserved.

Investigation of in vivo toxicity of hydroxylamine sulfate and the efficiency of intoxication treatment by α-tocopherol acetate and methylene blue.

Science.gov (United States)

Prodanchuk, Mykola G; Tsatsakis, Aristidis M; Prodanchuk, Georgiy M; Tsakalof, Andreas K

2013-11-01

Investigation of hydroxylamine sulfate toxicity mechanism in vivo and estimation of α-tocopherol acetate and methylene blue efficiency in poisoning treatments. In vivo experiments were conducted on 102 Wistar Han rats. The experiments investigated the hematotoxic and oxidative stress effects of hydroxylamine sulfate in acute and subacute toxicity treatment of animals. Electron Spin Resonance was used for quantitative determination of blood and liver tissue parameters alterations after intoxication. The osmotic fragility of erythrocytes, lipid peroxidation intensity and level of SH-groups in liver of rats were determined by established biochemical assays. Hydroxylamine sulfate cause an acute hematotoxicity and oxidative stress in vivo as demonstrated by the appearance of free oxidized iron in blood, reduced glutathione content and increased lipid peroxidation in liver. The experimental studies showed the formation of Hb-NO, MetHb in erythrocytes and as well of stable complex of reduced iron (Fe(2+)) with hydroxylamine sulfate. Methylene blue treatment does not reduce the Hb-NO or MetHb levels in intoxicated animals while administration of α-tocopherol acetate reduces substantially lipid peroxidation. Oxidative stress is a key mechanism of acute hematotoxicity caused by hydroxylamine sulfate. Methylene blue is not suitable antidote in case of hydroxylamine intoxication. Copyright © 2013 Elsevier Ltd. All rights reserved.

A New Property of Conjugated Polymer PFP: Catalytic Degradation of Methylene Blue Aqueous Solution

Institute of Scientific and Technical Information of China (English)

无

2005-01-01

A new property of conjugated polymer poly(furancarbinol-co-phenol)(PFP) was studied.The target copolymer was used as a catalyst after proper heating treatment. And dye methylene blue (MB) could be fully degraded and largely mineralized on PFP, under natural light or even in dark, in a few minutes. Furthermore, the catalytic activity could be preserved after several runs and the catalyst was readily separated. The effect of calcination temperature was also observed.

Sol–gel synthesis of SnO{sub 2}–MgO nanoparticles and their photocatalytic activity towards methylene blue degradation

Energy Technology Data Exchange (ETDEWEB)

Bayal, Nisha; Jeevanandam, P., E-mail: jeevafcy@iitr.ernet.in

2013-10-15

Graphical abstract: - Highlights: • A simple sol–gel method for the synthesis of SnO{sub 2}–MgO nanoparticles is reported. • Band gap of SnO{sub 2} can be tuned by varying the magnesium content in SnO{sub 2}–MgO. • SnO{sub 2}–MgO shows good photocatalytic activity towards degradation of methylene blue. - Abstract: SnO{sub 2}–MgO mixed metal oxide nanoparticles were prepared by a simple sol–gel method. The nanoparticles were characterized by power X-ray diffraction, scanning electron microscopy coupled with energy dispersive X-ray analysis, transmission electron microscopy and UV–vis diffuse reflectance spectroscopy. The XRD results indicate the formation of mixed metal oxide nanoparticles and also a decrease of SnO{sub 2} crystallite size in the mixed metal oxide nanoparticles with increasing magnesium oxide content. The reflectance spectroscopy results show a blue shift of the band gap of SnO{sub 2} in the mixed metal oxide nanoparticles. The photocatalytic activity of the SnO{sub 2}–MgO nanoparticles was tested using the photodegradation of aqueous methylene blue in the presence of sunlight. The results indicate that the mixed metal oxide nanoparticles possess higher efficiency for the photodegradation of methylene blue compared to pure SnO{sub 2} nanoparticles.

Vastus lateralis single motor unit EMG at the same absolute torque production at different knee angles

NARCIS (Netherlands)

Altenburg, T.M.; de Haan, A.; Verdijk, P.W.; van Mechelen, W.; de Ruiter, C.J.

2009-01-01

Single motor unit electromyographic (EMG) activity of the knee extensors was investigated at different knee angles with subjects (n = 10) exerting the same absolute submaximal isometric torque at each angle. Measurements were made over a 20° range around the optimum angle for torque production

A study on the adsorption of methylene blue onto gum ghatti/TiO2nanoparticles-based hydrogel nanocomposite

CSIR Research Space (South Africa)

Mittal, Hemant

2016-07-01

Full Text Available The objective of this work was to study the isotherm and kinetic models for the adsorption of methylene blue (MB) onto a TiO(sub2) nanoparticle (TiO(sub2)NP)-containing hydrogel nanocomposite (HNC) of polyacrylamide-grafted gum ghatti (PAAm...

Gibbs free energy of transfer of a methylene group on {UCON + (sodium or potassium) phosphate salts} aqueous two-phase systems: Hydrophobicity effects

International Nuclear Information System (INIS)

Silverio, Sara C.; Rodriguez, Oscar; Teixeira, Jose A.; Macedo, Eugenia A.

2010-01-01

The Gibbs free energy of transfer of a suitable hydrophobic probe can be regarded as a measure of the relative hydrophobicity of the different phases. The methylene group (CH 2 ) can be considered hydrophobic, and thus be a suitable probe for hydrophobicity. In this work, the partition coefficients of a series of five dinitrophenylated-amino acids were experimentally determined, at 23 o C, in three different tie-lines of the biphasic systems: (UCON + K 2 HPO 4 ), (UCON + potassium phosphate buffer, pH 7), (UCON + KH 2 PO 4 ), (UCON + Na 2 HPO 4 ), (UCON + sodium phosphate buffer, pH 7), and (UCON + NaH 2 PO 4 ). The Gibbs free energy of transfer of CH 2 units were calculated from the partition coefficients and used to compare the relative hydrophobicity of the equilibrium phases. The largest relative hydrophobicity was found for the ATPS formed by dihydrogen phosphate salts.

Pseudopeptide-Based Hydrogels Trapping Methylene Blue and Eosin Y.

Science.gov (United States)

Milli, Lorenzo; Zanna, Nicola; Merlettini, Andrea; Di Giosia, Matteo; Calvaresi, Matteo; Focarete, Maria Letizia; Tomasini, Claudia

2016-08-16

We present herein the preparation of four different hydrogels based on the pseudopeptide gelator Fmoc-l-Phe-d-Oxd-OH (Fmoc=fluorenylmethyloxycarbonyl), either by changing the gelator concentration or adding graphene oxide (GO) to the water solution. The hydrogels have been analysed by rheological studies that demonstrated that pure hydrogels are slightly stronger compared to GO-loaded hydrogels. Then the hydrogels efficiency to trap the cationic methylene blue (MB) and anionic eosin Y (EY) dyes has been analyzed. MB is efficiently trapped by both the pure hydrogel and the GO-loaded hydrogel through π-π interactions and electrostatic interactions. In contrast, the removal of the anionic EY is achieved in less satisfactory yields, due to the unfavourable electrostatic interactions between the dye, the gelator and GO. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Utilization of zeolites synthesized from coal ash for methylene blue removal from water

Directory of Open Access Journals (Sweden)

Denise Alves Fungaro

2008-12-01

Full Text Available The adsorption of methylene blue from aqueous solution was carried out using zeolites synthesized from coal ash as low-cost adsorbents. The coal ash sample was converted to zeolites by hydrothermal treatment using different synthesis parameters. The materials were characterized by physical-chemical analysis, XRD and SEM studies. The adsorption isotherms can be fitted by Freundlich model. The values of the adsorption capacity of adsorbents were similar for adsorbents. Kinetic studies indicate that the adsorption follows pseudo-second-order kinetic model.

Photo-, sono- and sonophotocatalytic degradation of methylene blue using Fe3O4/ZrO2 composites catalysts

Science.gov (United States)

Kristianto, Y.; Taufik, A.; Saleh, R.

2017-07-01

In the present work, magnetite material Fe3O4/ZrO2 with various molar ratios was prepared by the two-step method (sol-gel followed by the ultrasonic-assisted method). The as-prepared samples were fairly characterized by various characterization methods, such as X-ray Diffraction (XRD), Vibrating Sample Magnetometer (VSM), Fourier Transform Infrared (FT-IR) and Thermal Gravimetric Analysis (TGA). The catalytic performance of the as-prepared samples was evaluated based on the degradation of methylene blue under UV light, ultrasound and combination of UV and ultrasound irradiation. The results revealed that the sample with Fe3O4:ZrO2 molar ratio of 0.5:1 showed the best catalytic performance under UV, ultrasound and UV + ultrasound irradiation. The degradation of methylene blue follows the order: sonophotocatalytic > sonocatalytic > photocatalytic. In addition, the effect of various scavengers has also been studied. Furthermore, all prepared samples could be used as a convenient recyclable catalyst.

Trends Analysis of rhBMP2 Utilization in Single-Level Anterior Lumbar Interbody Fusion in the United States.

Science.gov (United States)

Lao, Lifeng; Cohen, Jeremiah R; Buser, Zorica; Brodke, Darrel S; Yoon, S Tim; Youssef, Jim A; Park, Jong-Beom; Meisel, Hans-Joerg; Wang, Jeffrey C

2018-04-01

Retrospective case study. To evaluate the trends and demographics of recombinant human bone morphogenetic protein 2 (rhBMP2) utilization in single-level anterior lumbar interbody fusion (ALIF) in the United States. Patients who underwent single-level ALIF from 2005 to 2011 were identified by searching ICD-9 diagnosis and procedure codes in the PearlDiver Patient Records Database (PearlDiver Technologies, Fort Wayne, IN), a national database of orthopedic insurance records. The year of procedure, age, gender, and region of the United States were analyzed for each patient. A total of 921 patients were identified who underwent a single-level ALIF in this study. The average rate of single-level ALIF with rhBMP2 utilization increased (35%-48%) from 2005 to 2009, but sharply decreased to 16.7% in 2010 and 15.0% in 2011. The overall incidence of single-level ALIF without rhBMP2 (0.20 cases per 100 000 patients) was more than twice of the incidence of single-level ALIF with rhBMP2 (0.09 cases per 100 000 patients). The average rate of single-level ALIF with rhBMP2 utilization is highest in West (41.4%), followed by Midwest (33.3%), South (26.5%) and Northeast (22.2%). The highest incidence of single-level ALIF with rhBMP2 was observed in the group aged less than 65 years (compared with any other age groups, P level ALIF increased from 2006 to 2009, but decreased in 2010 and 2011. The Northeast region had the lowest incidence of rhBMP2 utilization. The group aged less than 65 years trended to have the higher incidence of single-level ALIF with rhBMP2 utilization.

An improved synthesis of 2,2−-((4-substituted phenyl methylene difurans by Ultrasound irradiation

Directory of Open Access Journals (Sweden)

Naween M. Yonis

2016-09-01

Full Text Available A new series of 2,2−((4-substituted phenyl methylene difuran was synthesized by one-pot cyclocondensation of aldehyde with excess furan at room temperature using trifluoro acetic acid as a catalyst under ultrasound irradiation in the absence of solvent. The products were compared with the classical condensation reactions. This method consistently enjoys the advantages of mild reaction conditions, excellent yields, easy work up and short time.

Biosorption of Acid Dye in Single and Multidye Systems onto Sawdust of Locust Bean (Parkia biglobosa Tree

Directory of Open Access Journals (Sweden)

Abdur-Rahim Adebisi Giwa

2016-01-01

Full Text Available Properties of raw sawdust of Parkia biglobosa, as a biosorbent for the removal of Acid Blue 161 dye in single, binary, and ternary dye systems with Rhodamine B and Methylene Blue dyes in aqueous solution, were investigated. The sawdust was characterized using Scanning Electron Microscopy, Fourier Transform Infrared spectrophotometry, X-ray diffraction, and pH point of zero charge. Batch adsorption experiments were carried out to determine the equilibrium characteristics, thermodynamics, and kinetics of the sorption processes. The data obtained were subjected to various isotherm and kinetics equations. The results showed that the adsorption processes were described by different isotherm models depending on the composition of the system; they were all spontaneous (ΔG ranges from −0.72 to −5.36 kJ/mol and endothermic (range of ΔH is 11.37–26.31 kJ/mol and with increased randomness with ΔS values of 55.55 and 98.78 J·mol/K for single and ternary systems, respectively. Pseudo-second-order kinetics model gave better fit for all the sorption systems studied irrespective of the differences in composition, with the initial and overall rate constants higher for the mixtures than for the single system (6.76 g·mg−1min−1. The presence of Rhodamine B and Methylene Blue had a synergetic effect on the maximum monolayer capacity of the adsorbent for Acid Blue 161 dye.

Dentist Material Selection for Single-Unit Crowns: Findings from The National Dental Practice-Based Research Network

Science.gov (United States)

Makhija, Sonia K.; Lawson, Nathaniel C.; Gilbert, Gregg H.; Litaker, Mark S.; McClelland, Jocelyn A.; Louis, David R.; Gordan, Valeria V.; Pihlstrom, Daniel J.; Meyerowitz, Cyril; Mungia, Rahma; McCracken, Michael S.

2016-01-01

Objectives Dentists enrolled in the National Dental Practice-Based Research Network completed a study questionnaire about techniques and materials used for single-unit crowns and an enrollment questionnaire about dentist/practice characteristics. The objectives were to quantify dentists’ material recommendations and test the hypothesis that dentist’s and practice’s characteristics are significantly associated with these recommendations. Methods Surveyed dentists responded to a contextual scenario asking what material they would use for a single-unit crown on an anterior and posterior tooth. Material choices included: full metal, porcelain-fused-to-metal (PFM), all-zirconia, layered zirconia, lithium disilicate, leucite-reinforced ceramic, or other. Results 1,777 of 2,132 eligible dentists responded (83%). The top 3 choices for anterior crowns were lithium disilicate (54%), layered zirconia (17%), and leucite-reinforced glass ceramic (13%). There were significant differences (p<0.05) by dentist’s gender, race, years since graduation, practice type, region, practice busyness, hours worked/week, and location type. The top 3 choices for posterior crowns were all-zirconia (32%), PFM (31%), and lithium disilicate (21%). There were significant differences (p<0.05) by dentist’s gender, practice type, region, practice busyness, insurance coverage, hours worked/week, and location type. Conclusions Network dentists use a broad range of materials for single-unit crowns for anterior and posterior teeth, adopting newer materials into their practices as they become available. Material choices are significantly associated with dentist’s and practice’s characteristics. Clinical Significance Decisions for crown material may be influenced by factors unrelated to tooth and patient variables. Dentists should be cognizant of this when developing an evidence-based approach to selecting crown material. PMID:27693778

Viability of the Fricke dosemeter doped with methylene blue; Viabilidade do dosimetro Fricke dopado com azul de metileno

Energy Technology Data Exchange (ETDEWEB)

Souza, V.L.B.; Santos, C.D.A.; Rodrigues, K.R.G.; Cunha, M.S.; Figueiredo, M.D.C.; Melo, R.T. [Centro Regional de Ciencias Nucleares do Nordeste (CRCN-NE/CNEN-PE), Recife, PE (Brazil)

2009-07-01

This work aims to find the possible utilization of the Fricke dosemeter doped with methylene blue (FMB) for the dosimetry of photodynamic therapy. The FMB was irradiated wit X rays and light emitted diodes demonstrating positive answers to the stimulus, being probably to be used for dosimetric objectives

Automated assembling of single fuel cell units for use in a fuel cell stack

Science.gov (United States)

Jalba, C. K.; Muminovic, A.; Barz, C.; Nasui, V.

2017-05-01

The manufacturing of PEMFC stacks (POLYMER ELEKTROLYT MEMBRAN Fuel Cell) is nowadays still done by hand. Over hundreds of identical single components have to be placed accurate together for the construction of a fuel cell stack. Beside logistic problems, higher total costs and disadvantages in weight the high number of components produce a higher statistic interference because of faulty erection or material defects and summation of manufacturing tolerances. The saving of costs is about 20 - 25 %. Furthermore, the total weight of the fuel cells will be reduced because of a new sealing technology. Overall a one minute cycle time has to be aimed per cell at the manufacturing of these single components. The change of the existing sealing concept to a bonded sealing is one of the important requisites to get an automated manufacturing of single cell units. One of the important steps for an automated gluing process is the checking of the glue application by using of an image processing system. After bonding the single fuel cell the sealing and electrical function can be checked, so that only functional and high qualitative cells can get into further manufacturing processes.

The use of chemical modified chitosan with succinic anhydride in the methylene blue adsorption

International Nuclear Information System (INIS)

Lima, Ilauro S.; Ribeiro, Emerson S.; Airoldi, Claudio

2006-01-01

The adsorption capacity of a-chitosan and its modified form with succinic anhydride was compared with the traditional adsorbent active carbon by using the dye methylene blue, employed in the textile industry. The isotherms for both biopolymers were classified as SSA systems in the Giles model, more specifically in L class and subgroup 3. The dye concentration in the supernatant in the adsorption assay was determined through electronic spectroscopy. By calorimetric titration thermodynamic data of the interaction between methylene blue and the chemically modified chitosan at the solid/liquid interface were obtained. The enthalpy of the dye/chitosan interaction gave 2.47 ± 0.02 kJ mol-1 with an equilibrium constant of 7350 ± 10 and for the carbon/dye interaction this constant gave 5951 ± 8. The spontaneity of these adsorptions are reflected by the free Gibbs energies of -22.1 ± 0.4 and -21.5 ± 0.2 kJ mol-1, respectively, found for these systems. This new adsorbent derived from a natural polysaccharide is as efficient as activated carbon. However 97% of the bonded dye can be eluted by sodium chloride solution, while this same operation elutes only 42% from carbon. Chitosan is efficient in dye removal with the additional advantage of being cheap, non-toxic, biocompatible and biodegradable. (author)

Photocatalytic dechlorination of PCB 138 using leuco-methylene blue and visible light; reaction conditions and mechanisms

International Nuclear Information System (INIS)

Izadifard, Maryam; Langford, Cooper H.; Achari, Gopal

2010-01-01

A study of dechlorination of PCB 138, under visible light employing methylene blue (MB) and triethylamine (TEA) in acetonitrile/water has been conducted to investigate the details of the mechanism of dechlorination and to determine the efficiency of the process for this representative congener. Two other amines, N-methyldiethanolamine (MEDA) and (triethanolamine) TEOA also replaced TEA and two other solvents, methanol and ethanol replacing acetonitrile were examined for effects on reaction rates. The results show that PCB 138 can be dechlorinated efficiently in this photocatalytic reaction. Clarifying ambiguities in several previous reports, the reduced form of MB, leuco-methylene blue (LMB) was identified as responsible for the photoreaction with its excited state transferring an electron to PCBs; oxidized LMB (i.e. MB) is reduced back to LMB by the excess amine present. The reaction depends on a cycle driven by the amine as a sacrificial electron donor. MEDA proved to be the most efficient electron donor; apparently in consequence of the most favourable steady state concentration of LMB. Methanol and ethanol may be used to replace acetonitrile with little change in the efficiency of the reaction.

Obtaining multifunctional composites using styrofoam recycling: methylene blue adsorption

International Nuclear Information System (INIS)

Silva, T.H. da; Ferreira, B.F.; Faria, E.H. de; Ciuffi, K.J.; Calefi, P.S.

2011-01-01

There is high risk of environmental contamination by the textile industry if the generated waste is disposed into water streams and rivers. Another sector responsible for the generation of large amounts of waste is the styrofoam industry, since styrofoam is employed in various areas for packaging production. Therefore, today there is constant search for sustainable economic growth by means of materials recycling and reduction of residual pollutants. In this context, the present work aims to promote styrofoam recycling with its further utilization in the production of a kaolin-styrofoam composite for application as adsorbent of methylene blue originated from textile industry effluents. This adsorption is investigated in a column system, by exploiting the adsorptive properties of kaolin, such as large surface area and chemical and structural characteristics. The obtained materials were characterized by thermogravimetric analysis, X-ray diffraction, and UV-visible absorption spectroscopy. (author)

Potential Biosorbent Derived from Calligonum polygonoides for Removal of Methylene Blue Dye from Aqueous Solution

Science.gov (United States)

Nasrullah, Asma; Khan, Hizbullah; Khan, Amir Sada; Man, Zakaria; Muhammad, Nawshad; Khan, Muhammad Irfan; Abd El-Salam, Naser M.

2015-01-01

The ash of C. polygonoides (locally called balanza) was collected from Lakki Marwat, Khyber Pakhtunkhwa, Pakistan, and was utilized as biosorbent for methylene blue (MB) removal from aqueous solution. The ash was used as biosorbent without any physical or chemical treatment. The biosorbent was characterized by using various techniques such as Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). The particle size and surface area were measured using particle size analyzer and Brunauer-Emmett-Teller equation (BET), respectively. The SEM and BET results expressed that the adsorbent has porous nature. Effects of various conditions such as initial concentration of methylene blue (MB), initial pH, contact time, dosage of biosorbent, and stirring rate were also investigated for the adsorption process. The rate of the adsorption of MB on biomass sample was fast, and equilibrium has been achieved within 1 hour. The kinetics of MB adsorption on biosorbent was studied by pseudo-first- and pseudo-second-order kinetic models and the pseudo-second-order has better mathematical fit with correlation coefficient value (R 2) of 0.999. The study revealed that C. polygonoides ash proved to be an effective, alternative, inexpensive, and environmentally benign biosorbent for MB removal from aqueous solution. PMID:25705714

Electrochemical behavior of an anticancer drug 5-fluorouracil at methylene blue modified carbon paste electrode

International Nuclear Information System (INIS)

Bukkitgar, Shikandar D.; Shetti, Nagaraj P.

2016-01-01

A novel sensor for the determination of 5-fluorouracil was constructed by electrochemical deposition of methylene blue on surface of carbon paste electrode. The electrode surface morphology was studied using Atomic force microscopy and XRD. The electrochemical activity of modified electrode was characterized using cyclic voltammetry and differential pulse method. The developed sensor shows impressive enlargement in sensitivity of 5-fluorouracil determination. The peak currents obtained from differential pulse voltammetry was linear with concentration of 5-fluorouracil in the range 4 × 10 −5 –1 × 10 −7 M and detection limit and quantification limit were calculated to be 2.04 nM and 6.18 nM respectively. Further, the sensor was successfully applied in pharmaceutical and biological fluid sample analysis. - Highlights: • Electrochemical oxidation of 5-fluorouracil has been investigated for first time at methylene blue modified carbon paste electrode • The electrode process was irreversible and diffusion controlled • Probable electrochemical mechanism was proposed which involved two proton and two electron transfer reaction • The LOD and LOQ values were calculated to be 2.04 nM and 6.18 nM, respectively, with good selectivity and sensitivity. • Proposed method was applied to 5-Fluorouracil determination in pharmaceutical and spiked human urine samples

Determine the Intensity of UV Radiation and H2O2 on the Removal of Methylene Blue from Synthetic Wastewater

Directory of Open Access Journals (Sweden)

Mehdi Hosseini

2015-03-01

Full Text Available Background: There is a tremendous amount of color in textile wastewater that discharge it to the environment can cause a lot of environmental problems. The aim of this study is to evaluate the photocatalytic process UV/H2O2 to remove methylene blue dye from synthetic wastewater. Methods: UVC lamp was used as light source. In this study the effect of UV light intensity, irradiation distance, hydrogen peroxide concentration, and reaction time on the removal of methylene blue from aqueous solutions were studied. Data was analyzed by SPSS 18 and excel software. Results: The result showed that with increasing concentration of hydrogen peroxide, the color removal increases. Color removal changes were negligible at H2O2 concentration more than 5 mM. After 10 minutes reaction time at H2O2 concentration of 1 mm, efficiency of UVC/H2O2 is equal to 36.6%. Whilst at 5 mM concentration, removal efficiency is 89.2%. By increasing intensity of UV radiation, dye removal measure is also was increased, as the highest percentage of dye removal was obtained at 24 W radiation intensity. Conclusion: in present study, type of radiation and measure of hydrogen peroxide were the main factors in removal of methylene blue. Due to high efficiency of UVC/H2O2 process in removal of dye from aqueous solution, this method can use as an efficient process for removal of dye.

New diphosphonate compounds for skeletal imaging: comparison with methylene diphosphonate

International Nuclear Information System (INIS)

Subramanian, G.; McAfee, J.G.; Thomas, F.D.; Feld, T.A.; Zapf-Longo, C.; Palladino, E.

1983-01-01

Three-hour biodistribution of Tc-99m complexes of six diphosphonates was compared in rabbits with tibial lesions to determine which was best for detection of focal bone lesions. Sr-85 was used as a standard. N,N-dimethylaminomethylene diphosphonate (DMAD) was the only agent with a higher lesion/normal bone ratio than methylene diphosphonate (MDP), attributable to lower concentration in normal bone. Hydroxymethane diphosphonate (HDP) and 2,3-dicarboxypropane-1, 1-diphosphonate (DPD) demonstrated higher concentration than MDP in normal bone without improving lesion contrast. They also exhibited much higher uptake in the liver and kidney, as well as muscle and red marrow in the case of DPD. None was superior to MDP as an all-purpose skeletal agent, though others may be better for specific applications

Stereoselectivity in metallocene-catalyzed coordination polymerization of renewable methylene butyrolactones: From stereo-random to stereo-perfect polymers

KAUST Repository

Chen, Xia; Caporaso, Lucia; Cavallo, Luigi; Chen, Eugene You Xian

2012-01-01

Coordination polymerization of renewable α-methylene-γ-(methyl) butyrolactones by chiral C 2-symmetric zirconocene catalysts produces stereo-random, highly stereo-regular, or perfectly stereo-regular polymers, depending on the monomer and catalyst structures. Computational studies yield a fundamental understanding of the stereocontrol mechanism governing these new polymerization reactions mediated by chiral metallocenium catalysts. © 2012 American Chemical Society.

Stereoselectivity in metallocene-catalyzed coordination polymerization of renewable methylene butyrolactones: From stereo-random to stereo-perfect polymers

KAUST Repository

Chen, Xia

2012-05-02

Coordination polymerization of renewable α-methylene-γ-(methyl) butyrolactones by chiral C 2-symmetric zirconocene catalysts produces stereo-random, highly stereo-regular, or perfectly stereo-regular polymers, depending on the monomer and catalyst structures. Computational studies yield a fundamental understanding of the stereocontrol mechanism governing these new polymerization reactions mediated by chiral metallocenium catalysts. © 2012 American Chemical Society.

Experimental and kinetic studies on methylene blue adsorption by coir pith carbon.

Science.gov (United States)

Kavitha, D; Namasivayam, C

2007-01-01

Varying the parameters such as agitation time, dye concentration, adsorbent dose, pH and temperature carried out the potential feasibility of thermally activated coir pith carbon prepared from coconut husk for removal of methylene blue. Greater percentage of dye was removed with decrease in the initial concentration of dye and increase in amount of adsorbent used. Kinetic study showed that the adsorption of dye on coir pith carbon was a gradual process. Lagergren first-order, second-order, intra particle diffusion model and Bangham were used to fit the experimental data. Equilibrium isotherms were analysed by Langmuir, Freundlich, Dubnin-Radushkevich, and Tempkin isotherm. The adsorption capacity was found to be 5.87 mg/g by Langmuir isotherm for the particle size 250-500 microm. The equilibrium time was found to be 30 and 60 min for 10 and 20 mg/L and 100 min for 30, 40 mg/L dye concentrations, respectively. A maximum removal of 97% was obtained at natural pH 6.9 for an adsorbent dose of 100 mg/50 mL and 100% removal was obtained for an adsorbent dose of 600 mg/50 mL of 10 mg/L dye concentration. The pH effect and desorption studies suggest that chemisorption might be the major mode of the adsorption process. The change in entropy (DeltaS0) and heat of adsorption (DeltaH0) of coir pith carbon was estimated as 117.20 J/mol/K and 30.88 kJ/mol, respectively. The high negative value of change in Gibbs free energy indicates the feasible and spontaneous adsorption of methylene blue on coir pith carbon.

Enhanced visible-light-response photocatalytic degradation of methylene blue on Fe-loaded BiVO4 photocatalyst

International Nuclear Information System (INIS)

Chala, Sinaporn; Wetchakun, Khatcharin; Phanichphant, Sukon; Inceesungvorn, Burapat; Wetchakun, Natda

2014-01-01

Highlights: • Fe-loaded BiVO 4 particles were prepared by hydrothermal method. • Physicochemical properties played a significant role in photocatalytic process. • All Fe-loaded BiVO 4 samples showed higher photocatalytic activity than pure BiVO 4 . • The Fe 3+ ions may improve the separation of photogenerated electrons and holes. - Abstract: Pure BiVO 4 and nominal 0.5–5.0 mol% Fe-loaded BiVO 4 samples were synthesized by hydrothermal method. All samples were characterized in order to obtain the correlation between structure and photocatalytic properties by X-ray diffraction, Brunauer, Emmett and Teller, UV–vis diffuse reflectance spectrophotometry, photoluminescence spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and inductively coupled plasma-optical emission spectroscopy. The structure of all samples was single-phase monoclinic scheelite. The absorption spectrum of 5.0 mol% Fe-loaded BiVO 4 shifted to the visible region, suggesting the potential application of this material as a superior visible-light driven photocatalyst in comparison with pure BiVO 4 . Photocatalytic activities of all photocatalyst samples were examined by studying the degradation of methylene blue under visible light irradiation. The results clearly showed that Fe-loaded BiVO 4 sample exhibited remarkably higher activity than pure BiVO 4

Insertion of linear 8.4 μm diameter 16 channel carbon fiber electrode arrays for single unit recordings

Science.gov (United States)

Patel, Paras R.; Na, Kyounghwan; Zhang, Huanan; Kozai, Takashi D. Y.; Kotov, Nicholas A.; Yoon, Euisik; Chestek, Cynthia A.

2016-01-01

Objective Single carbon fiber electrodes (d=8.4 μm) insulated with parylene-c and functionalized with PEDOT:pTS have been shown to record single unit activity but manual implantation of these devices with forceps can be difficult. Without an improvement in the insertion method any increase in the channel count by fabricating carbon fiber arrays would be impractical. In this study, we utilize a water soluble coating and structural backbones that allow us to create, implant, and record from fully functionalized arrays of carbon fibers with ~150 μm pitch. Approach Two approaches were tested for the insertion of carbon fiber arrays. The first method used a PEG coating that temporarily stiffened the fibers while leaving a small portion at the tip exposed. The small exposed portion (500 μm – 1 mm) readily penetrated the brain allowing for an insertion that did not require the handling of each fiber by forceps. The second method involved the fabrication of silicon support structures with individual shanks spaced 150 μm apart. Each shank consisted of a small groove that held an individual carbon fiber. Main results Our results showed that the PEG coating allowed for the chronic implantation of carbon fiber arrays in 5 rats with unit activity detected at 31 days post-implant. The silicon support structures recorded single unit activity in 3 acute rat surgeries. In one of those surgeries a stacked device with 3 layers of silicon support structures and carbon fibers was built and shown to readily insert into the brain with unit activity on select sites. Significance From these studies we have found that carbon fibers spaced at ~150 μm readily insert into the brain. This greatly increases the recording density of chronic neural probes and paves the way for even higher density devices that have a minimal scarring response. PMID:26035638

Hydrothermal Synthesized and Alkaline Activated Carbons Prepared from Glucose and Fructose—Detailed Characterization and Testing in Heavy Metals and Methylene Blue Removal

Directory of Open Access Journals (Sweden)

Sanja Krstić

2018-06-01

Full Text Available In the presented paper, activated carbons were prepared from fructose and glucose, and activating agents (KOH, NaOH, LiOH by hydrothermal treatment (HTC treatment. After preparation, samples were characterized in details. Different techniques were used: x-ray powder diffraction analysis, Raman spectral analysis, elemental analysis, and determination of textural and morphological properties. Obtained results showed dependence of investigated properties and the nature of precursors (glucose or fructose as well as the type of hydroxides used as activating agents. After characterization, samples were tested as materials for heavy metals (Pb2+, Cd2+ and Zn2+ and methylene blue removal. Also, adsorption experiments were performed on wastewaters taken from tailings of the lead and zinc mine and kinetic of the methylene blue removal was studied. The factors which distinguished the KOH activated samples were high yield (~14%, content of organic carbon (63–74%, porosity and specific surface area (SBET ~700–1360 m2/g, a low degree of the crystal phase, indications that potassium ions may be included in heavy metals removal, good removal of the heavy metal ions (~47–59 mg/g for Pb2+, ~21–27 mg/g for Cd2+ and ~6–10 mg/g for Zn2+ and fast (~10–30 min and good methylene blue (~60–200 mg/g removal.

A prospective randomized trial comparing patent blue and methylene blue for the detection of the sentinel lymph node in breast cancer patients

Directory of Open Access Journals (Sweden)

Régis Resende Paulinelli

Full Text Available Summary Introduction: Methylene blue is more widely available and less expensive than patent blue, with an apparently lower risk of anaphylaxis. Objective: The two dyes were compared regarding detection of the sentinel lymph node (SLN. Method: A prospective, randomized trial involved 142 patients with invasive breast carcinoma. Sixty-nine (49.3% assigned to patent blue (group A and 71 (50.70% to methylene blue (group B. Thirty-five patients (25.0% were clinical stage III or IV; 55 (38.7% had axillary lymph nodes affected; and 69 (49.3% underwent neoadjuvant chemotherapy. Two patients were excluded because the dye type was not recorded. Results: Patients and tumor characteristics were similar in both groups. SLNs were identified in 47 women (68.1% in group A and 43 (60.6% in group B (p=0.35. SLNs were affected in 22 cases (51.2% in group A and 21 (48.8% in group B (p=0.62. The SLN was the only node affected in 12 cases (54.5% in group A and six (33.3% in group B (p=0.18. The time and degree of difficulty involved in identifying the SLN were similar in both groups. There were no complications or allergies. Conclusion: Methylene blue performed as well as patent blue in identifying the SLN in breast cancer patients.

High-pressure homogenization associated hydrothermal process of palygorskite for enhanced adsorption of Methylene blue

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhifang [Center of Eco-materials and Green Chemistry, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); University of the Chinese Academy of Sciences, Beijing 100049 (China); Wang, Wenbo [Center of Eco-materials and Green Chemistry, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); R& D Center of Xuyi Attapulgite Applied Technology, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Xuyi 211700 (China); Wang, Aiqin, E-mail: aqwang@licp.cas.cn [Center of Eco-materials and Green Chemistry, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); R& D Center of Xuyi Attapulgite Applied Technology, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Xuyi 211700 (China)

2015-02-28

Graphical abstract: - Highlights: • Palygorskite was modified by a homogenization associated hydrothermal process. • The crystal bundles of PAL were disaggregated efficiently after modification. • The adsorption of palygorskite for Methylene blue was greatly enhanced. • MB-loaded palygorskite exhibits excellent resistance to acid and alkali solution. - Abstract: Palygorskite (PAL) was modified by a high-pressure homogenization assisted hydrothermal process. The effects of modification on the morphology, structure and physicochemical properties of PAL were systematically investigated by Field-emission scanning electron microscopy (FESEM), Transmission electron microscopy (TEM), Fourier transform infrared spectrometry (FTIR), Brunauer–Emmett–Teller (BET) analysis, X-ray diffraction (XRD) and Zeta potential analysis techniques, and the adsorption properties were systematically evaluated using Methylene blue (MB) as the model dye. The results revealed that the crystal bundles were disaggregated and the PAL nanorods became more even after treated via associated high-pressure homogenization and hydrothermal process, and the crystal bundles were dispersed as nanorods. The intrinsic crystal structure of PAL was remained after hydrothermal treatment, and the pore size calculated by the BET method was increased. The adsorption properties of PAL for MB were evidently improved (from 119 mg/g to 171 mg/g) after modification, and the dispersion of PAL before hydrothermal reaction is favorable to the adsorption. The desorption evaluation confirms that the modified PAL has stronger affinity with MB, which is benefit to fabricate a stable organic–inorganic hybrid pigment.

2-Deoxyglucose autoradiography of single motor units: labelling of individual acutely active muscle fibers

International Nuclear Information System (INIS)

Toop, J.; Burke, R.E.; Dum, R.P.; O'Donovan, M.J.; Smith, C.B.

1982-01-01

2-Deoxy-D-[1- 14 C]glucose (2DG) was given intravenously during repetitive stimulation of single motor units in adult cats and autoradiographs were made of frozen sections of the target muscles in order to evaluate methods designed to improve the spatial resolution of [ 14 C]2DG autoradiography. With the modifications used, acutely active muscle fibers, independently identified by depletion of intrafiber glycogen, were associated with highly localized accumulations of silver grains over the depleted fibers. The results indicate that [ 14 C]2DG autoradiography can successfully identify individual active muscle fibers and might in principle be used to obtain quantitative data about rates of glucose metabolism in single muscle fibers of defined histochemical type. The modifications may be applicable also to other tissues to give improved spatial resolution with [ 14 C]-labeled metabolic markers. (Auth.)

Pyrite-enhanced methylene blue degradation in non-thermal plasma water treatment reactor

Energy Technology Data Exchange (ETDEWEB)

Benetoli, Luis Otavio de Brito, E-mail: luskywalcker@yahoo.com.br [Departamento de Quimica, Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil); Cadorin, Bruno Mena; Baldissarelli, Vanessa Zanon [Departamento de Quimica, Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil); Geremias, Reginaldo [Departamento de Ciencias Rurais, Universidade Federal de Santa Catarina (UFSC), Curitibanos, SC (Brazil); Goncalvez de Souza, Ivan [Departamento de Quimica, Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil); Debacher, Nito Angelo, E-mail: debacher@qmc.ufsc.br [Departamento de Quimica, Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil)

2012-10-30

Highlights: Black-Right-Pointing-Pointer We use O{sub 2} as the feed gas and pyrite was added to the non-thermal plasma reactor. Black-Right-Pointing-Pointer The methylene blue removal by NTP increased in the presence of pyrite. Black-Right-Pointing-Pointer The total organic carbon content decreased substantially. Black-Right-Pointing-Pointer The acute toxicity test showed that the treated solution is not toxic. Black-Right-Pointing-Pointer The dye degradation occurs via electron impact as well as successive hydroxylation. - Abstract: In this study, methylene blue (MB) removal from an aqueous phase by electrical discharge non-thermal plasma (NTP) over water was investigated using three different feed gases: N{sub 2}, Ar, and O{sub 2}. The results showed that the dye removal rate was not strongly dependent on the feed gas when the electrical current was kept the same for all gases. The hydrogen peroxide generation in the water varied according to the feed gas (N{sub 2} < Ar < O{sub 2}). Using O{sub 2} as the feed gas, pyrite was added to the reactor in acid medium resulting in an accentuated increase in the dye removal, which suggests that pyrite acts as a Fenton-like catalyst. The total organic carbon (TOC) content of the dye solution decreased slightly as the plasma treatment time increased, but in the presence of the pyrite catalyst the TOC removal increased substantially. The acute toxicity test using Artemia sp. microcrustaceans showed that the treated solution is not toxic when Ar, O{sub 2} or O{sub 2}-pyrite is employed. Electrospray ionization mass spectrometry analysis (ESI-MS) of the treated samples indicated that the dye degradation occurs via high energy electron impact as well as successive hydroxylation in the benzene rings of the dye molecules.

Methylene Blue in Ventilator-Induced Lung Injury after Pneumonectomy: an Experimental Study

Directory of Open Access Journals (Sweden)

Ye. V Suborov

2007-01-01

Full Text Available Objective: to study the expediency and efficiency of using methylene blue (MB on a model of pneumectomy (PE and subsequent ventilator-induced lung injury (VILI in sheep. Materials and methods. The study was conducted at the Research Laboratory of University of Tromse. The experiment included 23 sheep weighing 41.0±4.9 kg. Thoracotomy and right-sided pneumonectomy were performed in the animals under general anesthesia and controlled artificial ventilation. After measurement of the parameters of systemic hemodynamics and extravascular water of the lung (EVWL, the animals were divided into 3 groups: 1 a control group (CG, n=7 with a tidal volume (TV of 6 ml/kg and an end-expiratory positive pressure (PEEP of 2 cm H2O; 2 a VILI group (n=9 with a TV of 12 ml/kg and a PEEP of 0 cm H2O; 3 a group of MB (n=7 that was given in parallel with a damaging ventilation mode. The thermodilution technique (using a Cold Z-021 monitor, (Pulsion, Germany was employed to measure volumetric parameters and EVWL. The parameters of pulmonary hemodynamics, respiratory mechanics, and blood gas composition were recorded. Results: After its reduction at PE, EVWL index increased during damaging ventilation in the VILI and MB groups. In addition, there was an increase in pulmonary artery wedge pressure after PE in the MB and VILI groups. In the latter group, arterial hypoxemia was observed at the end of the experiment. Along with this, after PE pulmonary compliance decreased and airway pressure elevated in the VILI and MB groups. Conclusion: In the presented model of VILI, MB does not prevent the development of postp-neumectomic edema of the lung. Key words: thermochromodilution, acute lung injury, pneumectomy, ventilator-induced lung injury, postpneumectomic edema of the lung, methylene blue.

Impact of single room design on the spread of multi-drug resistant bacteria in an intensive care unit.

NARCIS (Netherlands)

Halaby, Teysir; Al Naiemi, Nashwan; Beishuizen, Bert; Verkooijen, Roel; Ferreira, José A; Klont, Rob; Vandenbroucke-Grauls, Christina

2017-01-01

Cross-transmission of nosocomial pathogens occurs frequently in intensive care units (ICU). The aim of this study was to investigate whether the introduction of a single room policy resulted in a decrease in transmission of multidrug-resistant (MDR) bacteria in an ICU.

One-unit versus two-unit cord-blood transplantation for hematologic cancers.

Science.gov (United States)

Wagner, John E; Eapen, Mary; Carter, Shelly; Wang, Yanli; Schultz, Kirk R; Wall, Donna A; Bunin, Nancy; Delaney, Colleen; Haut, Paul; Margolis, David; Peres, Edward; Verneris, Michael R; Walters, Mark; Horowitz, Mary M; Kurtzberg, Joanne

2014-10-30

Umbilical-cord blood has been used as the source of hematopoietic stem cells in an estimated 30,000 transplants. The limited number of hematopoietic cells in a single cord-blood unit prevents its use in recipients with larger body mass and results in delayed hematopoietic recovery and higher mortality. Therefore, we hypothesized that the greater numbers of hematopoietic cells in two units of cord blood would be associated with improved outcomes after transplantation. Between December 1, 2006, and February 24, 2012, a total of 224 patients 1 to 21 years of age with hematologic cancer were randomly assigned to undergo double-unit (111 patients) or single-unit (113 patients) cord-blood transplantation after a uniform myeloablative conditioning regimen and immunoprophylaxis for graft-versus-host disease (GVHD). The primary end point was 1-year overall survival. Treatment groups were matched for age, sex, self-reported race (white vs. nonwhite), performance status, degree of donor-recipient HLA matching, and disease type and status at transplantation. The 1-year overall survival rate was 65% (95% confidence interval [CI], 56 to 74) and 73% (95% CI, 63 to 80) among recipients of double and single cord-blood units, respectively (P=0.17). Similar outcomes in the two groups were also observed with respect to the rates of disease-free survival, neutrophil recovery, transplantation-related death, relapse, infections, immunologic reconstitution, and grade II-IV acute GVHD. However, improved platelet recovery and lower incidences of grade III and IV acute and extensive chronic GVHD were observed among recipients of a single cord-blood unit. We found that among children and adolescents with hematologic cancer, survival rates were similar after single-unit and double-unit cord-blood transplantation; however, a single-unit cord-blood transplant was associated with better platelet recovery and a lower risk of GVHD. (Funded by the National Heart, Lung, and Blood Institute and the

2-(Hetero(aryl)methylene)hydrazine-1-carbothioamides as potent urease inhibitors.

Science.gov (United States)

Saeed, Aamer; Imran, Aqeel; Channar, Pervaiz A; Shahid, Mohammad; Mahmood, Wajahat; Iqbal, Jamshed

2015-02-01

A small series of 2-(hetero(aryl)methylene) hydrazine-1-carbothioamides including two aryl derivatives was synthesized and tested for their inhibitory activity against urease. Compound (E)-2-(Furan-2-ylmethylene) hydrazine-1-carbothioamide (3f), having a furan ring, was the most potent inhibitor of urease with an IC50 value of 0.58 μM. Molecular modeling was carried out through docking the designed compounds into the urease binding site to predict whether these derivatives have analogous binding mode to the urease inhibitors. The study revealed that all of the tested compounds bind with both metal atoms at the active site of the enzyme. The aromatic ring of the compounds forms ionic interactions with the residues, Ala(440), Asp(494), Ala(636), and Met(637). © 2014 John Wiley & Sons A/S.

Lot-sizing for a single-stage single-product production system with rework of perishable production defectives

NARCIS (Netherlands)

Teunter, R.; Flapper, S.D.P.

2003-01-01

We consider a single-stage single-product production system. Produced units may be non-defective, reworkable defective, or non-reworkable defective. The system switches between production and rework. After producing a fixed number (N) of units, all reworkable defective units are reworked. Reworkable

Photocatalytic degradation of methylene blue dye using Fe{sub 2}O{sub 3}/TiO{sub 2} nanoparticles prepared by sol–gel method

Energy Technology Data Exchange (ETDEWEB)

Ahmed, M.A., E-mail: abdelhay71@hotmail.com [Chemistry Department, Faculty of Science, Ain-Shams University (Egypt); El-Katori, Emad E.; Gharni, Zarha H. [Chemistry Department, Faculty of Science, King Khaled University (Saudi Arabia)

2013-03-15

Graphical abstract: Photocatalytic degradation of methylene blue dye was successfully carried over Fe{sub 2}O{sub 3}/TiO{sub 2} nanorods embedded various proportion of Fe{sub 2}O{sub 3} (0–20) wt.%. Highlights: ► Fe{sub 2}O{sub 3}/TiO{sub 2} nano mixed oxide samples were successfully synthesized by sol–gel method. ► Manipulation of particle size and structure were achieved by micelle template approach. ► Both adsorption and photocatalytic reactivity are the main reasons for exceptional decolorization of methylene blue dye. ► A new mechanism for electronic transition between TiO{sub 2} and Fe{sub 2}O{sub 3} was proposed. -- Abstract: The photocatalytic degradation of methylene blue dye was successfully carried under UV irradiation over Fe{sub 2}O{sub 3}/TiO{sub 2} nanoparticles embedded various composition of Fe{sub 2}O{sub 3} (0–20) wt.% synthesized by sol–gel process. Structural and textural features of the mixed oxide samples were investigated by X-ray diffraction [XRD], Fourier transformer infra-red [FTIR], Energy dispersive X-ray [EDX], Field emission electron microscope [FESEM] and transmission electron microscope [TEM]. However, the optical features were estimated using UV–Vis spectrophotometer. The results reveal that the incorporation of various Fe{sub 2}O{sub 3} up to 7% is associated by remarkable increase in surface area, reduction of particle size, stabilization of anatase phase, shifting the photoexcitation response of the sample to visible region and exceptional degradation of methylene blue dye. On the other hand, increasing Fe{sub 2}O{sub 3} contents up to 20 wt.% is associated by anatase–rutile transformation, increasing in particle size and remarkable decrease in surface area which are prime factors in reducing the degradation process. The experimental results indicate that Fe{sub 2}O{sub 3}/TiO{sub 2} nanoparticles having both the advantages of photodegradation–adsorption process which considered a promising new

Scientific Basis for Paint Stripping: Elucidated Combinatorial Mechanism of Methylene Chloride and Phenol Based Paint Removers

Science.gov (United States)

2014-01-22

TiO2 9.5 Isobutyl ketone 0.1 Iron oxide hydrate 2.5 n-Butyl acid phosphate 0.1 Carbazole dioxazine violet ɘ.1 Bentone 0.5 Table 3: MIL-PRF-85285...partial formulation films, with pigments and no fillers, and full formulation films of current military polyurethane coatings were analyzed in this...time of the solvents. 22-01-2014 Memorandum Report Paint stripper Methylene chloride Phenol Polyurethane 7 June 2012 – 6 June 2013 SERDP WP-2244

Novel silicone-based polymer containing active methylene designed for the removal of indoor formaldehyde

Energy Technology Data Exchange (ETDEWEB)

Niu, Song, E-mail: niusong84@163.com; Yan, Hongxia, E-mail: hongxiayan@nwpu.edu.cn

2015-04-28

Highlights: • A novel silicone-based polymer with active methylene was explored. • Surface tension of liquid paints could be lowered using the polymer. • The polymer was easy to migrate toward the air-coating interface. • Free HCHO could effectively be removed using the polymer. • A lights on HCHO reduction without complicated preparation procedure was shielded. - Abstract: Indoor air pollution is caused inevitably due to complicated home decoration, in which formaldehyde is one of the most typical pollutants. It will be a convenient, economical and effective strategy to remove indoor formaldehyde if imparting a feature of formaldehyde removal to decorative coatings. We have successfully explored a novel silicone-based polymer containing active methylene used as a formaldehyde absorbent in coatings via a straightforward transesterification process using inexpensive and easily available chemicals. The polymer has been characterized by {sup 13}C NMR, FTIR, GC and GPC. Formaldehyde removal capacity of the coating films containing different contents of the polymer has been investigated. The results indicated that coatings incorporating 4 wt% of the polymer could make the coating films exhibit significant improvement on formaldehyde removal including purificatory performance (>85%) and durability of purificatory effect (>60%), compared to those consisting of absorbents without any silicon, and improve yellowing resistance performance, while other properties, such as gloss, adhesion, pencil hardness, flexibility and impact resistance, were kept almost unaffected. The chemical absorption process of the silicone-based polymer filled in interior decorative coatings is demonstrated as a promising technology to purify indoor formaldehyde and thus can reduce the harm to individuals.

Differing effects of attention in single-units and populations are well predicted by heterogeneous tuning and the normalization model of attention.

Science.gov (United States)

Hara, Yuko; Pestilli, Franco; Gardner, Justin L

2014-01-01

Single-unit measurements have reported many different effects of attention on contrast-response (e.g., contrast-gain, response-gain, additive-offset dependent on visibility), while functional imaging measurements have more uniformly reported increases in response across all contrasts (additive-offset). The normalization model of attention elegantly predicts the diversity of effects of attention reported in single-units well-tuned to the stimulus, but what predictions does it make for more realistic populations of neurons with heterogeneous tuning? Are predictions in accordance with population-scale measurements? We used functional imaging data from humans to determine a realistic ratio of attention-field to stimulus-drive size (a key parameter for the model) and predicted effects of attention in a population of model neurons with heterogeneous tuning. We found that within the population, neurons well-tuned to the stimulus showed a response-gain effect, while less-well-tuned neurons showed a contrast-gain effect. Averaged across the population, these disparate effects of attention gave rise to additive-offsets in contrast-response, similar to reports in human functional imaging as well as population averages of single-units. Differences in predictions for single-units and populations were observed across a wide range of model parameters (ratios of attention-field to stimulus-drive size and the amount of baseline response modifiable by attention), offering an explanation for disparity in physiological reports. Thus, by accounting for heterogeneity in tuning of realistic neuronal populations, the normalization model of attention can not only predict responses of well-tuned neurons, but also the activity of large populations of neurons. More generally, computational models can unify physiological findings across different scales of measurement, and make links to behavior, but only if factors such as heterogeneous tuning within a population are properly accounted for.

[Single- and multi-unit fixed dental prostheses in relation to the occlusal system].

Science.gov (United States)

Witter, D J; Gerritsen, A E; van Spijker, A; Creugers, N H J

2013-02-01

Occlusion concepts based on functional aspects offer more solid ground in the diagnostic process and in the treatment of (reduced) dentitions than morphologically and mechanically oriented occlusion concepts. Nevertheless, for occlusal reconstruction morphologically oriented guidelines are necessary. These guidelines are based on the border movements and positions of the mandible in the orofacial system, and on the location and modelling of the occlusal contacts in the occlusal system. The modelling of single- and multi-unit fixed dental prostheses must harmonize with the occlusal system. Moreover, an important feature is the relation of the anterior teeth which enables mutually protected occlusion. Characteristics of a healthy orofacial and occlusal system are: absence of pathology, perceived sufficient oral functions, variability inform and function, and adaptive capacity. When designing single- or multiunit fixed dental prostheses, a pragmatic starting point is to maintain the existing occlusion and the existing speech pattern unless arguments can be provided for alterations. The occlusal design should aim at optimizing oral functions, such as mandibular and occlusal stability.

SrTiO3 Nanocube-Doped Polyaniline Nanocomposites with Enhanced Photocatalytic Degradation of Methylene Blue under Visible Light

Directory of Open Access Journals (Sweden)

Syed Shahabuddin

2016-02-01

Full Text Available The present study highlights the facile synthesis of polyaniline (PANI-based nanocomposites doped with SrTiO3 nanocubes synthesized via the in situ oxidative polymerization technique using ammonium persulfate (APS as an oxidant in acidic medium for the photocatalytic degradation of methylene blue dye. Field emission scanning electron microscopy (FESEM, transmission electron microscopy (TEM, thermogravimetric analysis (TGA, X-ray diffraction (XRD, UV–Vis spectroscopy, Brunauer–Emmett–Teller analysis (BET and Fourier transform infrared spectroscopy (FTIR measurements were used to characterize the prepared nanocomposite photocatalysts. The photocatalytic efficiencies of the photocatalysts were examined by degrading methylene blue (MB under visible light irradiation. The results showed that the degradation efficiency of the composite photocatalysts that were doped with SrTiO3 nanocubes was higher than that of the undoped polyaniline. In this study, the effects of the weight ratio of polyaniline to SrTiO3 on the photocatalytic activities were investigated. The results revealed that the nanocomposite P-Sr500 was found to be an optimum photocatalyst, with a 97% degradation efficiency after 90 min of irradiation under solar light.

Preparation and characterization of poly(AA co PVP)/PGS composite and its application for methylene blue adsorption.

Science.gov (United States)

Yang, Cai-xia; Lei, Lei; Zhou, Peng-xin; Zhang, Zhe; Lei, Zi-qiang

2015-04-01

Poly (AA co PVP)/PGS (PAPP) composite adsorbent was prepared by radical polymerization from Acrylic acid (AA), Polyvinylpyrrolidone (PVP) and Palygorskite (PGS), using N,N-methylenebisacrylamide (MBA) as cross-linker and potassium persulfate (KPS) as initiator. The PAPP was characterized with Fourier transform infrared (FT-IR), thermogravimetric analysis (TG), scanning electron microscope (SEM) and transmission electron microscopy (TEM). PAPP was used as adsorbent for the removal of methylene blue from aqueous solutions. The influences of pH, adsorption temperature and adsorption time on the adsorption properties of the composite to the dye were also investigated. Meanwhile, the adsorption rate data and adsorption equilibrium date were analyzed based on the pseudo-first-order and pseudo-second-order kinetic model, Langmuir and Freundlich isotherm models, respectively. The results indicating that the kinetic behavior better fit with the pseudo-second-order kinetic model. The maximum equilibrium adsorption capacity (q(m)) is 1815 mg/g at 289 K. The isotherm behavior can be explained by the Langmuir isotherm models. The activation energy was also evaluated for the removal of methylene blue onto PAPP. These results demonstrate that this composite material could be used as a good adsorbent for the removal of cationic dyes from wastewater. Copyright © 2014 Elsevier Inc. All rights reserved.

Antibacterial activity of berberine-NorA pump inhibitor hybrids with a methylene ether linking group.

Science.gov (United States)

Samosorn, Siritron; Tanwirat, Bongkot; Muhamad, Nussara; Casadei, Gabriele; Tomkiewicz, Danuta; Lewis, Kim; Suksamrarn, Apichart; Prammananan, Therdsak; Gornall, Karina C; Beck, Jennifer L; Bremner, John B

2009-06-01

Conjugation of the NorA substrate berberine and the NorA inhibitor 5-nitro-2-phenyl-1H-indole via a methylene ether linking group gave the 13-substituted berberine-NorA inhibitor hybrid, 3. A series of simpler arylmethyl ether hybrid structures were also synthesized. The hybrid 3 showed excellent antibacterial activity (MIC Staphylococcus aureus, 1.7 microM), which was over 382-fold more active than the parent antibacterial berberine, against this bacterium. This compound was also shown to block the NorA efflux pump in S. aureus.

Novel methylene bridged ethylenediamine-type ligands: Synthesis and spectral characterization

Directory of Open Access Journals (Sweden)

Mihajlović-Lalić Ljiljana E.

2014-01-01

Full Text Available Herein we report the synthesis of two new organic compounds, diisobutyl- and diisopentyl N,N′-methylene-(S,S-ethylenediamine-N,N′-di-2-(3-cyclohexylpropanoate. A one-pot procedure was carried out by adding the reducing agent and carbonyl compound into the methanol solution of the parent compounds (iso-butyl and iso-pentyl esters of (S,S-ethylenediamine-N,N′-di-2-(3-cyclohexylpropanoic acid in appropriate stoichiometric ratios. The compounds were fully characterized by infrared, ESI-MS, 1D (1H, 13C and 2D (COSY, HSQC, HMBC NMR spectroscopy and elemental analysis. The spectral data confirm the presence of -CH2- group introduced between nitrogen atoms of the ethylenediamine moiety revealing neutral form of potential bidentate ligand. [Projekat Ministarstva nauke Republike Srbije, br. 172035. The authors also acknowledge the support of the FP7 RegPot project FCUB ERA GA No. 256716. The EC does not share responsibility for the content of the article

Technetium 99m methylene diphosphonate bone scanning in osteoarthritic hands

International Nuclear Information System (INIS)

Buckland-Wright, J.C.; Lynch, J.A.; Macfarlane, D.G.; Homoeopathic Hospital, Tunbridge; Fogelman, I.; Emery, P.

1991-01-01

In this prospective study, the radiological features characteristic of osteoarthritis of the hand were compared with the radionuclide bone scan images. A total of 32 patients was assessed at 6-monthly intervals for 18 months. Microfocal radiographs were taken at each visit. The high magnification and resolution of this technique permitted direct measurement of joint space width, subchondral sclerosis, osteophyte number and area and juxta-articular radiolucency area for each joint in the hand. Four-hour technetium 99m methylene diphosphonate bone scans were taken at 0 and 12 months and the activity of tracer uptake at each joint scored. The latter was compared with each X-radiographic feature at every visit and the changes between visits analysed. The scan scores did not correlate with any of the X-radiographic features other than osteophyte size. During the study the size of growing and remodelling osteophytes increased significantly at joints with raised or increased isotope uptake. (orig.)

Technetium 99m methylene diphosphonate bone scanning in osteoarthritic hands

Energy Technology Data Exchange (ETDEWEB)

Buckland-Wright, J.C.; Lynch, J.A. (United Medical and Dental Schools of Guy' s and Saint Thomas' , London (UK). Dept. of Anatomy); Macfarlane, D.G. (United Medical and Dental Schools of Guy' s and Saint Thomas' , London (UK). Dept. of Anatomy Homoeopathic Hospital, Tunbridge (UK). Dept. of Rheumatology); Fogelman, I. (United Medical and Dental Schools of Guy' s and Saint Thomas' , London (UK). Dept. of Nuclear Medicine); Emery, P. (United Medical and Dental Schools of Guy' s and Saint Thomas' , London (UK). Dept. of Rheumatology)

1991-01-01

In this prospective study, the radiological features characteristic of osteoarthritis of the hand were compared with the radionuclide bone scan images. A total of 32 patients was assessed at 6-monthly intervals for 18 months. Microfocal radiographs were taken at each visit. The high magnification and resolution of this technique permitted direct measurement of joint space width, subchondral sclerosis, osteophyte number and area and juxta-articular radiolucency area for each joint in the hand. Four-hour technetium 99m methylene diphosphonate bone scans were taken at 0 and 12 months and the activity of tracer uptake at each joint scored. The latter was compared with each X-radiographic feature at every visit and the changes between visits analysed. The scan scores did not correlate with any of the X-radiographic features other than osteophyte size. During the study the size of growing and remodelling osteophytes increased significantly at joints with raised or increased isotope uptake. (orig.).

Aesthetic rehabilitation of a patient with an anterior maxillectomy defect, using an innovative single-step, single unit, plastic-based hollow obturator

Directory of Open Access Journals (Sweden)

Vishwas Bhatia

2015-06-01

Full Text Available What could be better than improving the comfort and quality of life of a patient with a life-threatening disease? Maxillectomy, the partial or total removal of the maxilla in patients suffering from benign or malignant neoplasms, creates a challenging defect for the maxillofacial prosthodontist when attempting to provide an effective obturator. Although previous methods have been described for rehabilitation of such patients, our goal should be to devise one stage techniques that will allow the patient an improved quality of life as soon as possible. The present report describes the aesthetic rehabilitation of a maxillectomy patient by use of a hollow obturator. The obturator is fabricated through a processing technique which is a variation of other well-known techniques, consisting of the use of a single-step flasking procedure to fabricate a single-unit hollow obturator using the lost salt technique. As our aim is to aesthetically and functionally rehabilitate the patient as soon as possible, the present method of restoring the maxillectomy defect is cost-effective, time-saving and beneficial for the patient.

Synthesis and highly visible-induced photocatalytic activity of CNT-CdSe composite for methylene blue solution

Directory of Open Access Journals (Sweden)

Chen Ming-Liang

2011-01-01

Full Text Available Abstract Carbon nanotube-cadmium selenide (CNT-CdSe composite was synthesized by a facile hydrothermal method derived from multi-walled carbon nanotubes as a stating material. The as-prepared products were characterized by X-ray diffraction, scanning electron microscopy with energy dispersive X-ray analysis, transmission electron microscopy (TEM, and UV-vis diffuse reflectance spectrophotometer. The as-synthesized CNT-CdSe composite efficiently catalyzed the photodegradation of methylene blue in aqueous solutions under visible-light irradiation, exhibiting higher photocatalytic activity.

Criticality safety validation: Simple geometry, single unit 233U systems

International Nuclear Information System (INIS)

Putman, V.L.

1997-06-01

Typically used LMITCO criticality safety computational methods are evaluated for suitability when applied to INEEL 233 U systems which reasonably can be modeled as simple-geometry, single-unit systems. Sixty-seven critical experiments of uranium highly enriched in 233 U, including 57 aqueous solution, thermal-energy systems and 10 metal, fast-energy systems, were modeled. These experiments include 41 cylindrical and 26 spherical cores, and 41 reflected and 26 unreflected systems. No experiments were found for intermediate-neutron-energy ranges, or with interstitial non-hydrogenous materials typical of waste systems, mixed 233 U and plutonium, or reflectors such as steel, lead, or concrete. No simple geometry experiments were found with cubic or annular cores, or approximating infinite sea systems. Calculations were performed with various tools and methodologies. Nine cross-section libraries, based on ENDF/B-IV, -V, or -VI.2, or on Hansen-Roach source data, were used with cross-section processing methods of MCNP or SCALE. The k eff calculations were performed with neutral-particle transport and Monte Carlo methods of criticality codes DANT, MCNP 4A, and KENO Va

Synthesis of co-polymer-grafted gum karaya and silica hybrid organic–inorganic hydrogel nanocomposite for the highly effective removal of methylene blue

CSIR Research Space (South Africa)

Mittal, H

2015-11-01

Full Text Available The aim of this work was to study the adsorption behavior of the nanosilica-containing hydrogel nanocomposite of gum karaya grafted with poly(acrylic acid-acrylamide) (GK-cl-P(AA-co-AAM)) in the adsorption of methylene blue (MB) from aqueous...

Assessment of National Practice for Palliative Radiation Therapy for Bone Metastases Suggests Marked Underutilization of Single-Fraction Regimens in the United States

Energy Technology Data Exchange (ETDEWEB)

Rutter, Charles E., E-mail: charles.rutter@yale.edu [Department of Therapeutic Radiology, Yale School of Medicine, New Haven, Connecticut (United States); Yale Cancer Center, New Haven, Connecticut (United States); Yu, James B.; Wilson, Lynn D.; Park, Henry S. [Department of Therapeutic Radiology, Yale School of Medicine, New Haven, Connecticut (United States); Yale Cancer Center, New Haven, Connecticut (United States)

2015-03-01

Purpose: To characterize temporal trends in the application of various bone metastasis fractionations within the United States during the past decade, using the National Cancer Data Base; the primary aim was to determine whether clinical practice in the United States has changed over time to reflect the published randomized evidence and the growing movement for value-based treatment decisions. Patients and Methods: The National Cancer Data Base was used to identify patients treated to osseous metastases from breast, prostate, and lung cancer. Utilization of single-fraction versus multiple-fraction radiation therapy was compared according to demographic, disease-related, and health care system details. Results: We included 24,992 patients treated during the period 2005-2011 for bone metastases. Among patients treated to non-spinal/vertebral sites (n=9011), 4.7% received 8 Gy in 1 fraction, whereas 95.3% received multiple-fraction treatment. Over time the proportion of patients receiving a single fraction of 8 Gy increased (from 3.4% in 2005 to 7.5% in 2011). Numerous independent predictors of single-fraction treatment were identified, including older age, farther travel distance for treatment, academic treatment facility, and non-private health insurance (P<.05). Conclusions: Single-fraction palliative radiation therapy regimens are significantly underutilized in current practice in the United States. Further efforts are needed to address this issue, such that evidence-based and cost-conscious care becomes more commonplace.

Facile preparation of poly(methylene blue) modified carbon paste electrode for the detection and quantification of catechin

Energy Technology Data Exchange (ETDEWEB)

Manasa, G [Electrochemistry Research Group, Department of Chemistry, St. Joseph' s College, Lalbagh Road, Bangalore, 560027, Karnataka (India); Mascarenhas, Ronald J, E-mail: ronaldmasc2311@yahoo.co.in [Electrochemistry Research Group, Department of Chemistry, St. Joseph' s College, Lalbagh Road, Bangalore, 560027, Karnataka (India); Satpati, Ashis K [Analytical Chemistry Division, Bhabha Atomic Research Centre, Anushakthi Nagar, Trombay, Mumbai 400094, Maharashtra (India); D' Souza, Ozma J [Electrochemistry Research Group, Department of Chemistry, St. Joseph' s College, Lalbagh Road, Bangalore, 560027, Karnataka (India); Dhason, A [Soft Condensed Matter, Raman Research Institute, Sadashivnagar, Bangalore 560080, Karnataka (India)

2017-04-01

Free radicals are formed as byproducts of metabolism, and are highly unstable due to the presence of unpaired electrons. They readily react with other important cellular components such as DNA causing them damage. Antioxidants such as (+)-catechin (CAT), neutralize free radicals in the blood stream. Hence there is a need for detection and quantification of catechin concentration in various food sources and beverages. Electro-oxidative properties of catechin were investigated using cyclic voltammetry (CV) and differential pulse voltammetry (DPV). A carbon paste working electrode modified by electropolymerizing methylene blue (MB) was fabricated. Field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM) techniques were used to study the surface morphology of the electrode. Quasi-reversible electron transfer reaction occurred at + 0.260 V through a diffusion controlled process. In comparison to the bare carbon paste electrode (CPE), there was a significant 5.3 times increment in anodic current sensitivity at the modified electrode at physiological pH. Our findings indicate that for the electro-oxidation of CAT, CPE is a better base material for electropolymerization of MB compared to glassy carbon electrode (GCE). Nyquist plot followed the theoretical shape, indicating low interfacial charge transfer resistance of 0.095 kΩ at the modified electrode. Calibration plots obtained by DPV were linear in two ranges of 1.0 × 10{sup −3} to 1.0 × 10{sup −6} and 1.0 × 10{sup −7} to 0.1 × 10{sup −8} M. The limit of detection (LOD) and limit of quantification (LOQ) was 4.9 nM and 14 nM respectively. Application of the developed electrode was demonstrated by detecting catechin in green tea and spiked fruit juice with satisfactory recoveries. The sensor was stable, sensitive, selective and reproducible. - Highlights: • Remarkable electrocatalytic oxidation of Catechin at poly(methylene blue) modified CPE • Complete elimination of signal

SU-E-I-64: Transverse Relaxation Time in Methylene Protons of Non-Alcoholic Fatty Liver Disease Rats

Energy Technology Data Exchange (ETDEWEB)

Song, K-H; Lee, D-W; Choe, B-Y [Department of Biomedical Engineering, Research Institute of Biomedical Engineering, College of Medicine, The Catholic University of Korea, Seoul, Seoul (Korea, Republic of)

2015-06-15

Purpose: The aim of this study was to evaluate transverse relaxation time of methylene resonance compared to other lipid resonances. Methods: The examinations were performed using a 3.0 T scanner with a point — resolved spectroscopy (PRESS) sequence. Lipid relaxation time in a lipid phantom filled with canola oil was estimated considering repetition time (TR) as 6000 msec and echo time (TE) as 40 — 550 msec. For in vivo proton magnetic resonance spectroscopy ({sup 1}H — MRS), eight male Sprague — Dawley rats were given free access to a normal - chow (NC) and eight other male Sprague-Dawley rats were given free access to a high — fat (HF) diet. Both groups drank water ad libitum. T{sub 2} measurements in the rats’ livers were conducted at a fixed TR of 6000 msec and TE of 40 – 220 msec. Exponential curve fitting quality was calculated through the coefficients of determination (R{sup 2}). Results: A chemical analysis of phantom and liver was not performed but a T{sub 2} decay curve was acquired. The T{sub 2} relaxation time of methylene resonance was estimated as follows: NC rats, 37.07 ± 4.32 msec; HF rats, 31.43 ± 1.81 msec (p < 0.05). The extrapolated M0 values were higher in HF rats than in NC rats (p < 0.005). Conclusion: This study of {sup 1}H-MRS led to sufficient spectral resolution and signal — to — noise ratio differences to characterize all observable resonances for yielding T{sub 2} relaxation times of methylene resonance. {sup 1}H — MRS relaxation times may be useful for quantitative characterization of various liver diseases, including fatty liver disease. This study was supported by grant (2012-007883 and 2014R1A2A1A10050270) from the Mid-career Researcher Program through the NRF funded by Ministry of Science. In addition, this study was supported by the Industrial R&D of MOTIE/KEIT (10048997, Development of the core technology for integrated therapy devices based on real-time MRI-guided tumor tracking)

The use of intravenous hydroxocobalamin as a rescue in methylene blue-resistant vasoplegic syndrome in cardiac surgery

Directory of Open Access Journals (Sweden)

Yi Cai

2017-01-01

Full Text Available Vasoplegic syndrome is a well-recognized complication during cardiopulmonary bypass (CPB and is associated with increased morbidity and mortality, especially when refractory to conventional vasoconstrictor therapy. This is the first reported case of vasoplegia on CPB unresponsive to methylene blue whereas responsive to hydroxocobalamin, which indicates that the effect of hydroxocobalamin outside of the nitric oxide system is significant or that the two drugs have a synergistic effect in one or multiple mechanisms.

Prototype design of singles processing unit for the small animal PET

Science.gov (United States)

Deng, P.; Zhao, L.; Lu, J.; Li, B.; Dong, R.; Liu, S.; An, Q.

2018-05-01

Position Emission Tomography (PET) is an advanced clinical diagnostic imaging technique for nuclear medicine. Small animal PET is increasingly used for studying the animal model of disease, new drugs and new therapies. A prototype of Singles Processing Unit (SPU) for a small animal PET system was designed to obtain the time, energy, and position information. The energy and position is actually calculated through high precison charge measurement, which is based on amplification, shaping, A/D conversion and area calculation in digital signal processing domian. Analysis and simulations were also conducted to optimize the key parameters in system design. Initial tests indicate that the charge and time precision is better than 3‰ FWHM and 350 ps FWHM respectively, while the position resolution is better than 3.5‰ FWHM. Commination tests of the SPU prototype with the PET detector indicate that the system time precision is better than 2.5 ns, while the flood map and energy spectra concored well with the expected.

Two inorganic-organic hybrid materials based on polyoxometalate anions and methylene blue: Preparations, crystal structures and properties

International Nuclear Information System (INIS)

Nie Shanshan; Zhang Yaobin; Liu Bin; Li Zuoxi; Hu Huaiming; Xue Ganglin; Fu Feng; Wang Jiwu

2010-01-01

Two novel inorganic-organic hybrid materials based on an organic dye cation methylene blue (MB) and Lindqvist-type POM polyanions, [C 22 H 18 N 3 S] 2 Mo 6 O 19 2DMF (1) and [C 22 H 18 N 3 S] 2 W 6 O 19 2DMF (2) were synthesized under ambient conditions and characterized by CV, IR spectroscopy, solid diffuse reflectance spectrum, UV-vis spectra in DMF solution, luminescent spectrum and single crystal X-ray diffraction. Crystallographic data reveal that compounds 1 and 2 are isostructural and both crystallize in the triclinic space group P1-bar . Their crystal structures present that the layers of organic molecules and inorganic anions array alternatively, and there exist strong π...π stacking interactions between dimeric MB cations and near distance interactions among organic dye cations, Lindqvist-type POM polyanions and DMF molecules. The solid diffuse reflectance spectra and UV-vis spectra in DMF solution appear new absorption bands ascribed to the charge-transfer transition between the cationic MB donor and the POM acceptors. Studies of the photoluminescent properties show that the formation of 1 and 2 lead to the fluorescence quenching of starting materials. -- Graphical abstract: Their crystal structures present that the layers of organic molecules and inorganic anions array alternatively, and there exist strong π...π stacking interactions between dimeric MB cations. Display Omitted

Enhanced visible-light-response photocatalytic degradation of methylene blue on Fe-loaded BiVO{sub 4} photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Chala, Sinaporn [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Wetchakun, Khatcharin [Program of Physics, Faculty of Science, Ubon Ratchathani Rajabhat University, Ubon Ratchathani 34000 (Thailand); Phanichphant, Sukon [Materials Science Research Centre, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Inceesungvorn, Burapat [Department of Chemistry, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Wetchakun, Natda, E-mail: natda_we@yahoo.com [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

2014-06-01

Highlights: • Fe-loaded BiVO{sub 4} particles were prepared by hydrothermal method. • Physicochemical properties played a significant role in photocatalytic process. • All Fe-loaded BiVO{sub 4} samples showed higher photocatalytic activity than pure BiVO{sub 4}. • The Fe{sup 3+} ions may improve the separation of photogenerated electrons and holes. - Abstract: Pure BiVO{sub 4} and nominal 0.5–5.0 mol% Fe-loaded BiVO{sub 4} samples were synthesized by hydrothermal method. All samples were characterized in order to obtain the correlation between structure and photocatalytic properties by X-ray diffraction, Brunauer, Emmett and Teller, UV–vis diffuse reflectance spectrophotometry, photoluminescence spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and inductively coupled plasma-optical emission spectroscopy. The structure of all samples was single-phase monoclinic scheelite. The absorption spectrum of 5.0 mol% Fe-loaded BiVO{sub 4} shifted to the visible region, suggesting the potential application of this material as a superior visible-light driven photocatalyst in comparison with pure BiVO{sub 4}. Photocatalytic activities of all photocatalyst samples were examined by studying the degradation of methylene blue under visible light irradiation. The results clearly showed that Fe-loaded BiVO{sub 4} sample exhibited remarkably higher activity than pure BiVO{sub 4}.

Modification of bamboo-based activated carbon using microwave radiation and its effects on the adsorption of methylene blue

International Nuclear Information System (INIS)

Liu Qingsong; Zheng Tong; Li Nan; Wang Peng; Abulikemu, Gulizhaer

2010-01-01

Modification of bamboo-based activated carbon was carried out in a microwave oven under N 2 atmosphere. The virgin and modified activated carbons were characterized by means of low temperature N 2 adsorption, acid-base titration, point of zero charge (pH pzc ) measurement, FTIR and XPS spectra. A gradual decrease in the surface acidic groups was observed during the modification, while the surface basicity was enhanced to some extent, which gave rise to an increase in the pH pzc value. The species of the functional groups and relative content of various elements and groups were given further analysis using FTIR and XPS spectra. An increase in the micropores was found at the start, and the micropores were then extended into larger ones, resulting in an increase in the pore volume and average pore size. Adsorption studies showed enhanced adsorption of methylene blue on the modified activated carbons, caused mainly by the enlargement of the micropores. Adsorption isotherm fittings revealed that Langmuir and Freundlich models were applicable for the virgin and modified activated carbons, respectively. Kinetic studies exhibited faster adsorption rate of methylene blue on the modified activated carbons, and the pseudo-second-order model fitted well for all of the activated carbons.

Modification of bamboo-based activated carbon using microwave radiation and its effects on the adsorption of methylene blue

Energy Technology Data Exchange (ETDEWEB)

Liu Qingsong; Zheng Tong; Li Nan [State Key Laboratory of Urban Water Resource and Environment, School of Municipal and Environmental Engineering, Harbin Institute of Technology, Harbin 150090 (China); Wang Peng, E-mail: pwang73@vip.sina.com [State Key Laboratory of Urban Water Resource and Environment, School of Municipal and Environmental Engineering, Harbin Institute of Technology, Harbin 150090 (China); Abulikemu, Gulizhaer [State Key Laboratory of Urban Water Resource and Environment, School of Municipal and Environmental Engineering, Harbin Institute of Technology, Harbin 150090 (China)

2010-03-01

Modification of bamboo-based activated carbon was carried out in a microwave oven under N{sub 2} atmosphere. The virgin and modified activated carbons were characterized by means of low temperature N{sub 2} adsorption, acid-base titration, point of zero charge (pH{sub pzc}) measurement, FTIR and XPS spectra. A gradual decrease in the surface acidic groups was observed during the modification, while the surface basicity was enhanced to some extent, which gave rise to an increase in the pH{sub pzc} value. The species of the functional groups and relative content of various elements and groups were given further analysis using FTIR and XPS spectra. An increase in the micropores was found at the start, and the micropores were then extended into larger ones, resulting in an increase in the pore volume and average pore size. Adsorption studies showed enhanced adsorption of methylene blue on the modified activated carbons, caused mainly by the enlargement of the micropores. Adsorption isotherm fittings revealed that Langmuir and Freundlich models were applicable for the virgin and modified activated carbons, respectively. Kinetic studies exhibited faster adsorption rate of methylene blue on the modified activated carbons, and the pseudo-second-order model fitted well for all of the activated carbons.

Modification of bamboo-based activated carbon using microwave radiation and its effects on the adsorption of methylene blue

Science.gov (United States)

Liu, Qing-Song; Zheng, Tong; Li, Nan; Wang, Peng; Abulikemu, Gulizhaer

2010-03-01

Modification of bamboo-based activated carbon was carried out in a microwave oven under N 2 atmosphere. The virgin and modified activated carbons were characterized by means of low temperature N 2 adsorption, acid-base titration, point of zero charge (pH pzc) measurement, FTIR and XPS spectra. A gradual decrease in the surface acidic groups was observed during the modification, while the surface basicity was enhanced to some extent, which gave rise to an increase in the pH pzc value. The species of the functional groups and relative content of various elements and groups were given further analysis using FTIR and XPS spectra. An increase in the micropores was found at the start, and the micropores were then extended into larger ones, resulting in an increase in the pore volume and average pore size. Adsorption studies showed enhanced adsorption of methylene blue on the modified activated carbons, caused mainly by the enlargement of the micropores. Adsorption isotherm fittings revealed that Langmuir and Freundlich models were applicable for the virgin and modified activated carbons, respectively. Kinetic studies exhibited faster adsorption rate of methylene blue on the modified activated carbons, and the pseudo-second-order model fitted well for all of the activated carbons.

Spinal meningeal uptake of technetium-99m methylene diphosphonate in meningeal seeding by malignant lymphoma

International Nuclear Information System (INIS)

Siegal, T.; Or, R.; Matzner, Y.; Samuels, L.D.

1980-01-01

Definite diagnosis of meningeal seeding by systemic cancer relies on the presence of malignant cells in the cerebrospinal fluid (CSF). In the absence of such cells in the CSF, only two other tests strongly suggest the diagnosis - a CT scan and a myelogram. This paper reports a case in which the diagnosis was strongly suggested by an unusual uptake of Tc-99m methylene diphosphonate by the leptomeninges during a skeletal scan and later established by the presence of malignant cells in the CSF. The radionuclide scan may be an additional diagnostic test in some cases with meningeal seeding by systemic cancer

Fe(III/TiO2-Montmorillonite Photocatalyst in Photo-Fenton-Like Degradation of Methylene Blue

Directory of Open Access Journals (Sweden)

Is Fatimah

2015-01-01

Full Text Available A photodegradation process of methylene blue (MB in aqueous solution using Fe(III/TiO2-montmorillonite photocatalyst is presented. The photocatalyst material was prepared using Indonesian natural montmorillonite in TiO2 pillarization process followed by Fe(III ion exchange. Kinetic study on MB degradation was conducted and evaluated by three kinetic models: the pseudo-first- and second-order equations and the Elovich equation. From the results, it is concluded that the degradation under the photo-Fenton-like process utilizing Fe(III/TiO2-montmorillonite photocatalyst conformed to the Elovich kinetic model.

[Single-family rooms for neonatal intensive care units impacts on preterm newborns, families, and health-care staff. A systematic literature review].

Science.gov (United States)

Servel, A-C; Rideau Batista Novais, A

2016-09-01

The quality of the environment is an essential point in the care of preterm newborns. The design of neonatal intensive care units (NICUs) (open-bay, single-patient room, single-family room) directly affects both the preterm newborns and their caregivers (parents, healthcare staff). The aim of this systematic review was to evaluate the impact of single-family rooms on the preterm newborn, its parents, and the staff. Single-family rooms improve outcome for the preterm newborn, with increasing parental involvement and better control of the environment (fewer inappropriate stimulations such as high levels of noise and illumination). This kind of NICU design also improves parental and staff satisfaction. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Myths and memes about single-payer health insurance in the United States: a rebuttal to conservative claims.

Science.gov (United States)

Geyman, John P

2005-01-01

Recent years have seen the rapid growth of private think tanks within the neoconservative movement that conduct "policy research" biased to their own agenda. This article provides an evidence-based rebuttal to a 2002 report by one such think tank, the Dallas-based National Center for Policy Analysis (NCPA), which was intended to discredit 20 alleged myths about single-payer national health insurance as a policy option for the United States. Eleven "myths" are rebutted under eight categories: access, cost containment, quality, efficiency, single-payer as solution, control of drug prices, ability to compete abroad (the "business case"), and public support for a single-payer system. Six memes (self-replicating ideas that are promulgated without regard to their merits) are identified in the NCPA report. Myths and memes should have no place in the national debate now underway over the future of a failing health care system, and need to be recognized as such and countered by experience and unbiased evidence.

Clinical and immunologic findings of methylene diphenyl diisocyanate-induced occupational asthma in a car upholstery factory.

Science.gov (United States)

Hur, G-Y; Koh, D-H; Choi, G-S; Park, H-J; Choi, S-J; Ye, Y-M; Kim, K-S; Park, H-S

2008-04-01

Although methylene diphenyl diisocyanate (MDI) is widely used in many industries, there have been few immunological studies of MDI-induced occupational asthma. We investigated the effects of MDI exposure on the clinical and immunologic condition of workers in a single car upholstery factory. Fifty-eight MDI-exposed workers were studied. Work-related lower-respiratory symptoms (WRRS) were identified using a questionnaire. Serum-specific IgE and IgG antibodies to MDI-human serum albumin conjugate were detected by ELISA. Atopy was evaluated using a skin prick test. MDI-induced occupational asthma was confirmed in the symptomatic workers with a positive result on an MDI-specific inhalation test. Thirteen (22.4%) of the subjects complained of WRRS. MDI-induced occupational asthma was confirmed in five (8.6%) of the workers, and occupational eosinophilic bronchitis was confirmed in two (3.5%). The prevalence of specific IgG antibodies (20.7%) was higher than that of specific IgE antibodies (8.6%). The prevalence of MDI-induced occupational asthma/eosinophilic bronchitis was strongly associated with the presence of both WRRS and serum-specific IgG antibodies to an MDI-human serum albumin conjugate (Pworkers. The prevalence of MDI-induced occupational asthma was 8.6%, and MDI-induced eosinophilic bronchitis was confirmed in two workers. The presence of work-related lower-respiratory symptoms and serum-specific IgG antibodies to an MDI-human serum albumin conjugate may be used to predict MDI-induced occupational asthma/eosinophilic bronchitis in MDI-exposed workers.

Blood schizontocidal activity of methylene blue in combination with antimalarials against Plasmodium falciparum

Directory of Open Access Journals (Sweden)

Garavito G.

2007-06-01

Full Text Available Methylene blue (MB is the oldest synthetic antimalarial. It is not used anymore as antimalarial but should be reconsidered. For this purpose we have measured its impact on both chloroquine sensitive and resistant Plasmodium strains. We showed that around 5 nM of MB were able to inhibit 50% of the parasite growth in vitro and that late rings and early trophozoites were the most sensitive stages; while early rings, late trophozoites and schizonts were less sensitive. Drug interaction study following fractional inhibitory concentrations (FIC method showed antagonism with amodiaquine, atovaquone, doxycycline, pyrimethamine; additivity with artemether, chloroquine, mefloquine, primaquine and synergy with quinine. These results confirmed the interest of MB that could be integrated in a new low cost antimalarial combination therapy.

A Probability Analysis of the Generating Cost for EU-APR1400 Single Unit

International Nuclear Information System (INIS)

Ha, Gak Hyeon; Kim, Sung Hwan

2014-01-01

The nuclear power plant market is expected to grow rapidly in order to address issues of global warming, reducing CO 2 emissions and securing stable electricity supplies. Under these circumstances, the main primary goal of the EU-APR100 development is to ensure export competitiveness in the European countries. To this end, EU-APR1400 have been developed based one te APR1400 (Advanced Power Reactor, GEN Type) The EU-APR1400 adds many advanced design features to its predecessor, as outlined below in Table 1. In this simulation, the results of the generating cost of the EU-APR1400 single unit were determined using the probability cost analysis technique, the generating cost range was shown to be 56.16 ∼ 70.92 won/kWh.

A Probability Analysis of the Generating Cost for EU-APR1400 Single Unit

Energy Technology Data Exchange (ETDEWEB)

Ha, Gak Hyeon; Kim, Sung Hwan [KHNP CRI, Seoul (Korea, Republic of)

2014-10-15

The nuclear power plant market is expected to grow rapidly in order to address issues of global warming, reducing CO{sub 2} emissions and securing stable electricity supplies. Under these circumstances, the main primary goal of the EU-APR100 development is to ensure export competitiveness in the European countries. To this end, EU-APR1400 have been developed based one te APR1400 (Advanced Power Reactor, GEN Type) The EU-APR1400 adds many advanced design features to its predecessor, as outlined below in Table 1. In this simulation, the results of the generating cost of the EU-APR1400 single unit were determined using the probability cost analysis technique, the generating cost range was shown to be 56.16 ∼ 70.92 won/kWh.

A simple and rapid method for high-resolution visualization of single-ion tracks

Directory of Open Access Journals (Sweden)

Masaaki Omichi

2014-11-01

Full Text Available Prompt determination of spatial points of single-ion tracks plays a key role in high-energy particle induced-cancer therapy and gene/plant mutations. In this study, a simple method for the high-resolution visualization of single-ion tracks without etching was developed through the use of polyacrylic acid (PAA-N, N’-methylene bisacrylamide (MBAAm blend films. One of the steps of the proposed method includes exposure of the irradiated films to water vapor for several minutes. Water vapor was found to promote the cross-linking reaction of PAA and MBAAm to form a bulky cross-linked structure; the ion-track scars were detectable at a nanometer scale by atomic force microscopy. This study demonstrated that each scar is easily distinguishable, and the amount of generated radicals of the ion tracks can be estimated by measuring the height of the scars, even in highly dense ion tracks. This method is suitable for the visualization of the penumbra region in a single-ion track with a high spatial resolution of 50 nm, which is sufficiently small to confirm that a single ion hits a cell nucleus with a size ranging between 5 and 20 μm.

A simple and rapid method for high-resolution visualization of single-ion tracks

Energy Technology Data Exchange (ETDEWEB)

Omichi, Masaaki [Department of Applied Chemistry, Graduate School of Engineering, Osaka University, Osaka 565-0871 (Japan); Center for Collaborative Research, Anan National College of Technology, Anan, Tokushima 774-0017 (Japan); Choi, Wookjin; Sakamaki, Daisuke; Seki, Shu, E-mail: seki@chem.eng.osaka-u.ac.jp [Department of Applied Chemistry, Graduate School of Engineering, Osaka University, Osaka 565-0871 (Japan); Tsukuda, Satoshi [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, Sendai, Miyagi 980-8577 (Japan); Sugimoto, Masaki [Japan Atomic Energy Agency, Takasaki Advanced Radiation Research Institute, Gunma, Gunma 370-1292 (Japan)

2014-11-15

Prompt determination of spatial points of single-ion tracks plays a key role in high-energy particle induced-cancer therapy and gene/plant mutations. In this study, a simple method for the high-resolution visualization of single-ion tracks without etching was developed through the use of polyacrylic acid (PAA)-N, N’-methylene bisacrylamide (MBAAm) blend films. One of the steps of the proposed method includes exposure of the irradiated films to water vapor for several minutes. Water vapor was found to promote the cross-linking reaction of PAA and MBAAm to form a bulky cross-linked structure; the ion-track scars were detectable at a nanometer scale by atomic force microscopy. This study demonstrated that each scar is easily distinguishable, and the amount of generated radicals of the ion tracks can be estimated by measuring the height of the scars, even in highly dense ion tracks. This method is suitable for the visualization of the penumbra region in a single-ion track with a high spatial resolution of 50 nm, which is sufficiently small to confirm that a single ion hits a cell nucleus with a size ranging between 5 and 20 μm.

[Clinical use of virally inactived plasma. The experience of Blood Transfusion Unit in Mantova, Italy].

Science.gov (United States)

Lepri, Debora; Capuzzo, Enrico; Mattioli, Anna Vittoria; Dall'Oglio, Daniela; Sgarioto, Vincenzo; Terenziani, Isabella; Caramaschi, Giacomo; Manzato, Franco; Franchini, Massimo

2013-03-01

Fresh Frozen Plasma (FFP) is a blood component whose clinical use is widespread worldwide. Transfusion safety of this product is ensured by legally obligatory tests. Although these tests are carried out on each plasma donation, safety levels can be further improved by using some technical procedures, such as, among others, methylene blue (MB) and solvent-detergent (SD) viral inactivation methods. The DMTE (Blood Transfusion Unit) in Mantova has used the pharmaceutical-like SD virally inactivated plasma since 2007 (Plasmasafe, Kedrion) as replacement of the PFC by each single donor. Guidelines for the usage of both products are the same. With the main aim of assessing the therapeutic effectiveness and safety of Plasmasafe, we decided to clinically monitor transfusions performed with this product on patients of the Intensive Care Unit at the city hospital in Mantova. In addition, we controlled some coagulation parameters (PT, aPTT, ATIII, Fibrinogen, PC, PS, FV, FVII, FVIII) before and 24 hours after the Plasmasafe infusion. From a clinical point of view, the use of Plasmasafe always led to a significant reduction, or complete stop, of the bleeding. No transfusion-related adverse events were recorded. As regards, the most relevant laboratory results, a marked increase in the above mentioned hemostatic parameters was detected. Furthermore, patients transfused with this product received a mean volume significantly lower than an historical cohort of patients treated with FFP (503 mL with Plasmasafe versus 1549 mL with FFP, Pcost-effective treatment, able to rapidly correct hemostatic abnormalities, for critical patients.

Crash problem definition and safety benefits methodology for stability control for single-unit medium and heavy trucks and large-platform buses

Science.gov (United States)

2009-10-01

This report presents the findings of a comprehensive engineering analysis of electronic stability control (ESC) and roll stability control (RSC) systems for single-unit medium and heavy trucks and large-platform buses. This report details the applica...

Enhanced removal of Methylene Blue by electrocoagulation using iron electrodes

Directory of Open Access Journals (Sweden)

Mohamed S. Mahmoud

2013-06-01

Full Text Available The removal of pollutants from effluents by electrocoagulation has become an attractive method in recent years. The study deals with the enhancement of removal of Methylene Blue dye by using an electromagnetic field during the electrocoagulation process. Effects of electrolyte concentration, dye concentration, intensity and the direction of the electromagnet on the decolorization efficiency have been investigated. The formed ferric hydroxide flocs trap colloidal particles and make solid–liquid separation easier during the next stage. The electrocoagulation stages must be optimized in order to design an economically feasible process. The results showed that the optimum electrolysis was 10–20 min at a current density of 8 mA/cm2, while the optimum concentration of the electrolyte (NaOH was found to be 2 wt.% when the dye concentration was 50 mg/L. The utilization of an electromagnetic field enhanced the dye removal due to the induced motion of paramagnetic ions inside the solution. The power consumption required to remove the dye was reduced by 45% in the case of applying an electromagnetic field.

Decolorization of methylene blue in layered manganese oxide suspension with H2O2

International Nuclear Information System (INIS)

Zhang Lili; Nie Yulun; Hu Chun; Hu Xuexiang

2011-01-01

Highlights: → Layered birnessite-type manganese oxides exhibited a well-crystallized octahedral layer (OL) structure with β-MnOOH, α-MnOOH and γ-Mn 3 O 4 . → The catalyst was highly effective for the decolorization and degradation of methylene blue in the presence of H 2 O 2 at neutral pH. → The 1 O 2 and O 2 · - were the main reactive oxygen species in the reaction. - Abstract: Layered birnessite-type manganese oxides (Na-OL-1) were prepared via a redox reaction involving MnO 4 - and Mn 2+ under markedly alkaline conditions. According to the XRD analysis, the resulting material exhibited a well-crystallized octahedral layer (OL) structure with several different phases, including β-MnOOH, α-MnOOH and γ-Mn 3 O 4 . The catalyst was highly effective for the decolorization and degradation of methylene blue (MB) in the presence of H 2 O 2 at neutral pH. The tested MB was completely decolorized in Na-OL-1 suspension by the fraction dosing of H 2 O 2 (556.5 mM at the beginning and then 183.8 mM at 40 min). Based on the studies of electron spin resonance and the effect of radical scavengers, the 1 O 2 and O 2 · - were the main reactive oxygen species (ROS) in the reaction. It was found that both oxygen and ROS were generated from the decomposition of H 2 O 2 in Na-OL-1 suspension, wherein the decomposition pathways were proposed. The generation of H 2 O 2 in Na-OL-1 suspension at air atmosphere indicated that the existence of multivalent manganese oxides greatly enhanced the interfacial electron transfer, leading to the high activity of Na-OL-1.

Photocatalytic Degradation of Methylene Blue Using TiO2 Impregnated Diatomite

Directory of Open Access Journals (Sweden)

Ranfang Zuo

2014-01-01

Full Text Available Nano-TiO2 showed a good catalytic activity, but it is easy to agglomerate, resulting in the reduction or even complete loss of photocatalytic activity. The dispersion of TiO2 particles on porous materials was a potential solution to this problem. Diatomite has high specific surface and absorbability because of its particular shell structure. Thus, TiO2/diatomite composite, prepared by loading TiO2 on the surface of diatomite, was a good photocatalyst, through absorbing organic compounds with diatomite and degrading them with TiO2. Scanning electron microscopy (SEM, energy dispersive spectrum (EDS, X-ray diffraction (XRD, chemical analysis, and Fourier transform infrared spectrometry (FTIR indicated that TiO2 was impregnated well on the surface of diatomite. Furthermore, TiO2/diatomite was more active than nano-TiO2 for the degradation of methylene blue (MB in solution. MB at concentrations of 15 and 35 ppm can be completely degraded in 20 and 40 min, respectively.

Crystal Violet and Methylene Green as Low-Dose Liquid Dosimetry Systems

International Nuclear Information System (INIS)

Ebraheem, S.; Beshir, W.B.; Hassan, H.M.

2008-01-01

The ultimate aim of the present work is studying of the possibility of using some organic solutions for gamma radiation monitors and to evaluate and characterize the dosimetric properties of these compounds. Crystal violet (CV) and methylene green (MG) aqueous solutions with different concentrations have been prepared and irradiated to different absorbed doses. The solutions were readout using absorption spectrophotometry technique at λ m ax 592 nm and 614 nm for CV and MG respectively. The maximum useful dose range was investigated and found to be concentration dependent. It was found that the useful dose range was from 10-160 Gy for CV and from 10-200 Gy for MG. The radiation chemical yield, G-value, was calculated for the studied solutions. The ph effect and the effect of different additives, chloral hydrate and ethanol have been also investigated. The pre- and post- irradiation stabilities of these solutions under different storage conditions were studied and the results showed different significant dependence on the storage condition

Treatment Recommendations for Single-Unit Crowns: Findings from The National Dental Practice-Based Research Network

Science.gov (United States)

McCracken, Michael S.; Louis, David R.; Litaker, Mark S.; Minyé, Helena M.; Mungia, Rahma; Gordan, Valeria V.; Marshall, Don G.; Gilbert, Gregg H.

2016-01-01

Background Objectives were to: (1) quantify practitioner variation in likelihood to recommend a crown; and (2) test whether certain dentist, practice, and clinical factors are significantly associated with this likelihood. Methods Dentists in the National Dental Practice-Based Research Network completed a questionnaire about indications for single-unit crowns. In four clinical scenarios, practitioners ranked their likelihood of recommending a single-unit crown. These responses were used to calculate a dentist-specific “Crown Factor” (CF; range 0–12). A higher score implies a higher likelihood to recommend a crown. Certain characteristics were tested for statistically significant associations with the CF. Results 1,777 of 2,132 eligible dentists responded (83%). Practitioners were most likely to recommend crowns for teeth that were fractured, cracked, endodontically-treated, or had a broken restoration. Practitioners overwhelmingly recommended crowns for posterior teeth treated endodontically (94%). Practice owners, Southwest practitioners, and practitioners with a balanced work load were more likely to recommend crowns, as were practitioners who use optical scanners for digital impressions. Conclusions There is substantial variation in the likelihood of recommending a crown. While consensus exists in some areas (posterior endodontic treatment), variation dominates in others (size of an existing restoration). Recommendations varied by type of practice, network region, practice busyness, patient insurance status, and use of optical scanners. Practical Implications Recommendations for crowns may be influenced by factors unrelated to tooth and patient variables. A concern for tooth fracture -- whether from endodontic treatment, fractured teeth, or large restorations -- prompted many clinicians to recommend crowns. PMID:27492046

Adult bone strength of children from single-parent families: the Midlife in the United States Study.

Science.gov (United States)

Crandall, C J; Karlamangla, A S; Merkin, S S; Binkley, N; Carr, D; Greendale, G A; Seeman, T E

2015-03-01

Bone health may be negatively impacted by childhood socio-environmental circumstances. We examined the independent associations of single-parent childhood and parental death or divorce in childhood with adult bone strength indices. Longer exposure to a single-parent household in childhood was associated with lower bone strength in adulthood. Because peak bone mass is acquired during childhood, bone health may be negatively impacted by childhood socio-environmental disadvantage. The goal of this study was to determine whether being raised in a single-parent household is associated with lower bone strength in adulthood. Using dual-energy X-ray absorptiometry data from 708 participants (mean age 57 years) in the Midlife in the United States Biomarker Project, we examined the independent associations of composite indices of femoral neck bone strength relative to load (in three failure modes: compression, bending, and impact) in adulthood with the experience of single-parent childhood and parental death or divorce in childhood. After adjustment for gender, race, menopause transition stage, age, and body mass index, each additional year of single-parent childhood was associated with 0.02 to 0.03 SD lower indices of adult femoral neck strength. In those with 9-16 years of single-parent childhood, the compression strength index was 0.41 SD lower, bending strength index was 0.31 SD lower, and impact strength index was 0.25 SD lower (all p values divorce during childhood was not by itself independently associated with adult bone strength indices. The magnitudes of these associations were unaltered by additional adjustment for lifestyle factors and socioeconomic status in childhood and adulthood. Independent of parental death or divorce, growing up in a single-parent household is associated with lower femoral neck bone strength in adulthood, and this association is not entirely explained by childhood or adult socioeconomic conditions or lifestyle choices.

Acid-base catalysis of N-[(morpholine)methylene]daunorubicin.

Science.gov (United States)

Krause, Anna; Jelińska, Anna; Cielecka-Piontek, Judyta; Klawitter, Maria; Zalewski, Przemysław; Oszczapowicz, Irena; Wąsowska, Małgorzata

2012-08-01

The stability of N-[(morpholine)methylene]-daunorubicin hydrochloride (MMD) was investigated in the pH range 0.44-13.54, at 313, 308, 303 and 298 K. The degradation of MMD as a result of hydrolysis is a pseudo-first-order reaction described by the following equation: ln c = ln c(0) - k(obs)• t. In the solutions of hydrochloric acid, sodium hydroxide, borate, acetate and phosphate buffers, k(obs) = k(pH) because general acid-base catalysis was not observed. Specific acid-base catalysis of MMD comprises the following reactions: hydrolysis of the protonated molecules of MMD catalyzed by hydrogen ions (k(1)) and spontaneous hydrolysis of MMD molecules other than the protonated ones (k(2)) under the influence of water. The total rate of the reaction is equal to the sum of partial reactions: k(pH) = k(1) • a(H)+ • f(1) + k(2) • f(2) where: k(1) is the second-order rate constant (mol(-1) l s(-1)) of the specific hydrogen ion-catalyzed degradation of the protonated molecules of MMD; k(2) is the pseudo-first-order rate constant (s(-1)) of the water-catalyzed degradation of MMD molecules other than the protonated ones, f(1) - f(2) are fractions of the compound. MMD is the most stable at approx. pH 2.5.

A Novel of Buton Asphalt and Methylene Blue as Dye-Sensitized Solar Cell using TiO2/Ti Nanotubes Electrode

Science.gov (United States)

Nurhidayani; Muzakkar, M. Z.; Maulidiyah; Wibowo, D.; Nurdin, M.

2017-11-01

A study of TiO2/Ti nanotubes arrays (NTAs) based on Dye-Sensitized Solar Cell (DSSC) used Asphalt Buton (Asbuton) extract and methylene blue (MB) as a photosensitizer dye has been conducted. The aim of this research is that the Asbuton extract and Methylene Blue (MB) performance as a dye on DSSC solar cells is able to obtain the voltage-currents produced by visible light irradiation. Electrode TiO2/Ti NTAs have been successfully synthesized by anodizing methods, then characterized by using XRD showed that the anatase crystals formed. Subsequently, the morphology showed that the nanotubes formed which has coated by Asbuton extract. The DSSC system was formed by a sandwich structure and tested by using Multimeter Digital with Potentiostat instrument. The characteristics of current (I) and potential (V) versus time indicated that the Asbuton was obtained in a high-performance in 30s of 14,000µV 0.844µA, meanwhile MB dyes were 8,000µV0.573µA. Based on this research, the Asbuton extract from Buton Island-Southeast Sulawesi-Indonesia was potential for natural dyes in DSSC system.

Kinetic and Thermodynamics of Methylene Blue Adsorption onto Zero Valent Iron Supported on Mesoporous Silica

Directory of Open Access Journals (Sweden)

Atyaf Khalid Hameed

2016-08-01

Full Text Available Zero valent iron supported on mesoporous silicanano particles (NZVI/MSNs was prepared by the aqueous phase borohydride reduction methods. Prior to the reduction, mesoporous silica nanoparticles (MSNs were prepared through the activation of fumed silica with concentrated HCl by refluxing at 90 °C. FTIR, XRD, FESEM, EDX and BET were used to characterize theadsorbents prepared. BET surface areas of MSNs, NZVI, and NZVI/MSNs were 126, 41, and 72 m2/g for, respectively. The performance of NZVI/MSNs as adsorbent was examined by adsorption of methylene blue (MB, performed in series of batch experiments. In the kinetic studies, pseudo first order and pseudo second order kinetic models were examined. The pseudo second order equation provided the best fit with the experimental data. Thermodynamic studies indicated that the adsorption process is endothermic with ΔH° was 90.53 kJ/mol. Positive ΔS° (300 J/mol and negative ΔG° (-6.42 kJ/mol was recorded, indicating the spontaneous of the adsorption process and naturally favorable. Copyright © 2016 BCREC GROUP. All rights reserved Received: 5th March 2016; Revised: 18th March 2016; Accepted: 18th March 2016 How to Cite: Hameed, A.K., Dewayanto, N., Dongyun, D., Nordin, M.R., Mohd Hasbi Ab. Rahim, M.H.A. (2016. Kinetic and Thermodynamics of Methylene Blue Adsorption onto Zero Valent Iron Supported on Mesoporous Silica. Bulletin of Chemical Reaction Engineering & Catalysis, 11 (2: 250-261 (doi:10.9767/bcrec.11.2.443.250-261 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.11.2.443.250-261

Preparation, characterization and application of N-methylene phosphonic acid chitosan grafted magnesia–zirconia stationary phase

Energy Technology Data Exchange (ETDEWEB)

Wang, Qing; Chen, Jie; Huang, Kun; Zhang, Xin; Xu, Li [Tongji School of Pharmacy, Huazhong University of Science and Technology, Wuhan 430030 (China); Shi, Zhi-guo, E-mail: shizg@whu.edu.cn [Department of Chemistry, Wuhan University, Wuhan 430072 (China)

2015-01-07

Highlights: • N-methylene phosphonic acid chitosan grafted MgO–ZrO{sub 2} was prepared. • It exhibited superior HILIC chromatographic performance to the bare MgO–ZrO{sub 2}. • Monosaccharides, phospholipids and peptides were successfully separated. • It was a promising HILIC stationary phase. - Abstract: A hydrophilic stationary phase (SP) was prepared through grafting N-methylene phosphonic acid chitosan on magnesia–zirconia particles (P-CTS-MgO–ZrO{sub 2}) via Lewis acid–base interaction. The resulting material was characterized by thermogravimetric analysis, Fourier transform infrared spectroscopy, scanning electron microscope and nitrogen adsorption analysis. The chromatographic performance of P-CTS-MgO–ZrO{sub 2} was systemically evaluated by studying effect of acetonitrile content, pH and buffer concentration in the mobile phase. The results demonstrated that the novel SP provided hydrophilic, electrostatic-repulsion and ion-exchange interactions. Compared to the bare MgO–ZrO{sub 2}, P-CTS-MgO–ZrO{sub 2} exhibited superior peak shape, reasonable resolution and reduced analysis time in separation of basic analytes. Besides, remarkable resolving power of acids, i.e. six non-steroidal anti-inflammatory drugs which failed to be eluted from the bare MgO–ZrO{sub 2}, was obtained with the theoretical plate number (N/m) of 4653–31313, asymmetry factor <1.21 and the resolution of 1.6–3.4. Finally, P-CTS-MgO–ZrO{sub 2} SP was applied to separate monosaccharides, phospholipids and peptides. P-CTS-MgO–ZrO{sub 2} was a promising hydrophilic SP for wide applications.

Continuous adsorption of Pb(II) and methylene blue by engineered graphite oxide coated sand in fixed-bed column

Energy Technology Data Exchange (ETDEWEB)

Gong, Ji-Lai, E-mail: jilaigong@gmail.com [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Zhang, Yong-Liang; Jiang, Yan [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Zeng, Guang-Ming, E-mail: zgming@hnu.edu.cn [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Cui, Zhi-Hui; Liu, Ke; Deng, Can-Hui; Niu, Qiu-Ya; Deng, Jiu-Hua [College of Environmental Science and Engineering, Key Laboratory of Environmental Biology and Pollution Control, Ministry of Education, Hunan University, Changsha 410082 (China); Huan, Shuang-Yan [State Key Laboratory for Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082 (China)

2015-03-01

Highlights: • GO-sand was prepared by coating GO on the surface of sand. • Pb(II) and MB were efficiently removed by GO-sand filter in column. • The removal of MB was enhanced with the presence of Pb(II). • GO-sand is low-cost and convenient for its application as packed bed filter. - Abstract: The mixture of several effluents, caused by the improper handling and management of effluents, generated multi-component wastewater containing both metals and dyes, leading to the complicated treatment process. In this study, a continuous adsorption of Pb(II) and methylene blue (MB) has been studied in single and binary solutions by using graphite oxide coated sand (GO-sand) as an adsorbent in a fixed-bed column. GO-sand was analyzed by X-ray photoelectron spectroscopy before and after analyte adsorption. Compared with sand filter, adsorption quantity and capacity for Pb(II) and MB by GO-sand filter were greatly increased. In Pb(II) and MB single solutions, the experimental parameters were investigated in detail including initial concentration, flow rate, bed depth and pH. Exhaustion time decreased with increasing initial concentration and flow rate, and increased with increasing bed depth and pH. In the Pb(II)-MB binary solution, exhaustion time significantly decreased for Pb(II) adsorption, but increased for MB adsorption. The reason was explained that the more favorable adsorption for MB onto the surface of GO-sand than that for Pb(II), which was derived from π–π interaction between MB and GO on sand surface in packed filter. The Yoon–Nelson model was applied at different concentration of Pb(II) and MB to predict the breakthrough curves. The experimental data were well fit with the model indicating that it was suitable for this column design.

Technical evaluation of the electrical, instrumentation, and control design aspects of the proposed license amendment Revision 1 for single-loop operation of Browns Ferry Nuclear Plants (Docket No. 50-259, Unit 1; Docket No. 50-260, Unit 2; Docket No. 50-296, Unit 3)

International Nuclear Information System (INIS)

Donich, T.R.

1983-01-01

This report documents the technical evaluation of the proposed changes to the plant reactor protection system by the licensee of Browns Ferry Nuclear Power Station, Units 1, 2, and 3, to account for single-loop plant operation. This evaluation is restricted to only the electrical, instrumentation and control design aspects of proposed changes to the plant technical specifications for single-loop operation beyond 24 hours. Conclusion is that the license amendment for single-loop operation has met the review criteria provided sufficient administrative controls are in effect, and any anomalous control room indicators are corrected or warning-tagged for the duration of single-loop operation

Two pathogen reduction technologies--methylene blue plus light and shortwave ultraviolet light--effectively inactivate hepatitis C virus in blood products.

Science.gov (United States)

Steinmann, Eike; Gravemann, Ute; Friesland, Martina; Doerrbecker, Juliane; Müller, Thomas H; Pietschmann, Thomas; Seltsam, Axel

2013-05-01

Contamination of blood products with hepatitis C virus (HCV) can cause infections resulting in acute and chronic liver diseases. Pathogen reduction methods such as photodynamic treatment with methylene blue (MB) plus visible light as well as irradiation with shortwave ultraviolet (UVC) light were developed to inactivate viruses and other pathogens in plasma and platelet concentrates (PCs), respectively. So far, their inactivation capacities for HCV have only been tested in inactivation studies using model viruses for HCV. Recently, a HCV infection system for the propagation of infectious HCV in cell culture was developed. Inactivation studies were performed with cell culture-derived HCV and bovine viral diarrhea virus (BVDV), a model for HCV. Plasma units or PCs were spiked with high titers of cell culture-grown viruses. After treatment of the blood units with MB plus light (Theraflex MB-Plasma system, MacoPharma) or UVC (Theraflex UV-Platelets system, MacoPharma), residual viral infectivity was assessed using sensitive cell culture systems. HCV was sensitive to inactivation by both pathogen reduction procedures. HCV in plasma was efficiently inactivated by MB plus light below the detection limit already by 1/12 of the full light dose. HCV in PCs was inactivated by UVC irradiation with a reduction factor of more than 5 log. BVDV was less sensitive to the two pathogen reduction methods. Functional assays with human HCV offer an efficient tool to directly assess the inactivation capacity of pathogen reduction procedures. Pathogen reduction technologies such as MB plus light treatment and UVC irradiation have the potential to significantly reduce transfusion-transmitted HCV infections. © 2012 American Association of Blood Banks.

Theoretical evaluation of the efficiency of gas single-stage reciprocating compressor medium pressure units

Science.gov (United States)

Busarov, S. S.; Vasil'ev, V. K.; Busarov, I. S.; Titov, D. S.; Panin, Ju. N.

2017-08-01

Developed earlier and tested in such working fluid as air, the technology of calculating the operating processes of slow-speed long-stroke reciprocating stages let the authors to obtain successful results concerning compression of gases to medium pressures in one stage. In this connection, the question of the efficiency of the application of slow-speed long-stroke stages in various fields of technology and the national economy, where the working fluid is other gas or gas mixture, is topical. The article presents the results of the efficiency evaluation of single-stage compressor units on the basis of such stages for cases when ammonia, hydrogen, helium or propane-butane mixture is used as the working fluid.

Photocatalytic degradation of methylene blue dye by zinc oxide nanoparticles obtained from precipitation and sol-gel methods.

Science.gov (United States)

Balcha, Abebe; Yadav, Om Prakash; Dey, Tania

2016-12-01

Zinc oxide (ZnO) nanoparticles were synthesized by precipitation and sol-gel methods. The aim of this study was to understand how different synthetic methods can affect the photocatalytic activity of ZnO nanoparticles. As-synthesized ZnO nanoparticles were characterized by X-ray diffraction (XRD) and UV-Visible spectroscopic techniques. XRD patterns of ZnO powders synthesized by precipitation and sol-gel methods revealed their hexagonal wurtzite structure with crystallite sizes of 30 and 28 nm, respectively. Their photocatalytic activities were evaluated by photocatalytic degradation of methylene blue, a common water pollutant, under UV radiation. The effects of operational parameters such as photocatalyst load and initial concentration of the dye on photocatalytic degradation of methylene blue were investigated. While the degradation of dye decreased over the studied dye concentration range of 20 to 100 mg/L, an optimum photocatalyst load of 250 mg/L was needed to achieve dye degradation as high as 81 and 92.5 % for ZnO prepared by precipitation and sol-gel methods, respectively. Assuming pseudo first-order reaction kinetics, this corresponded to rate constants of 8.4 × 10 -3 and 12.4 × 10 -3  min -1 , respectively. Hence, sol-gel method is preferred over precipitation method in order to achieve higher photocatalytic activity of ZnO nanostructures. Photocatalytic activity is further augmented by better choice of capping ligand for colloidal stabilization, starch being more effective than polyethylene glycol (PEG).

A comparative study of the DG-OMEGA (DG Omega), DGII, and GAT method for the structure elucidation of a methylene-acetal linked thymine dinucleotide

NARCIS (Netherlands)

van Kampen, A. H. C.; Beckers, M. L. M.; Buydens, L. M. C.

1997-01-01

This research continues the investigation of the properties of the recently developed structure elucidation method DG-OMEGA (DG Omega). Towards this end it was applied for the structure determination of a methylene-acetal linked thymine dinucleotide. The performance of DG Omega was compared to the

THE DEGRADATION OF METHYLENE BLUE OVER M2TiO4 SPINEL PHOTOCATALYST

Directory of Open Access Journals (Sweden)

N FODIL CHERIF

2014-06-01

Full Text Available Heterogeneous photocatalysis is an advanced oxidation process (AOP which has been widely studied by numerous researchers in the world and is used to degrade or remove a wide range of pollutants in water and air. In this study, the photocatalytic oxidation and mineralization of methylene blue in aqueous catalyst suspensions of coprecipitated cobalt titanium oxide has been carried out in a helical reactor. The photodegradation was investigated using two kinds of irradiation lamps one emitting at 254 nm and the other emitting at 365 nm. Results showed that photodegradation is an effective method for the removal of MB from wastewaters. The efficiency of the process depends strongly on the experimental conditions of synthesis. We observed that 40 % of pollutant was degraded after 3 hours of UV irradiation.

Solubility limit of methyl red and methylene blue in microemulsions and liquid crystals of water, sds and pentanol systems

OpenAIRE

Beri, D.; Pratami, A.; Gobah, P. L.; Dwimala, P.; Amran, A.

2017-01-01

Solubility of dyes in amphiphilic association structures of water, SDS and penthanol system (i.e. in the phases of microemulsions and liquid crystals) was attracted much interest due to its wide industrial and technological applications. This research was focused on understanding the solubility limitation of methyl red and methylene blue in microemulsion and liquid crystal phases. Experimental results showed that the highest solubility of methyl red was in LLC, followed by w/o microemulsion a...

Trends Analysis of rhBMP Utilization in Single-Level Posterior Lumbar Interbody Fusion in the United States.

Science.gov (United States)

Lao, Lifeng; Cohen, Jeremiah R; Buser, Zorica; Brodke, Darrel S; Youssef, Jim A; Park, Jong-Beom; Yoon, S Tim; Wang, Jeffrey C; Meisel, Hans-Joerg

2017-10-01

Retrospective study. Recombinant human bone morphogenetic protein-2 (rhBMP-2) has been widely used in spinal fusion surgery, but there is little information on rhBMP-2 utilization in single-level posterior lumbar interbody fusion (PLIF). The purpose of our study was to evaluate the trends and demographics of rhBMP-2 utilization in single-level PLIF. Patients who underwent single-level PLIF from 2005 to 2011 were identified by searching ICD-9 diagnosis and procedure codes in the PearlDiver Patient Records Database, a national database of orthopedic insurance records. The year of procedure, age, gender, and region of the United States were recorded for each patient. Results were reported for each variable as the incidence of procedures identified per 100 000 patients searched in the database. A total of 2735 patients had single-level PLIF. The average rate of single-level PLIF with rhBMP-2 maintained at a relatively stable level (28% to 31%) from 2005 to 2009, but decreased in 2010 (9.9%) and 2011 (11.8%). The overall incidence of single-level PLIF without rhBMP-2 (0.68 cases per 100 000 patients) was statistically higher ( P level PLIF with rhBMP-2 (0.21 cases per 100 000 patients). The average rate of single-level PLIF with rhBMP-2 utilization was the highest in West (30.1%), followed by Midwest (26.9%), South (20.5%), and Northeast (17.8%). The highest incidence of single-level PLIF with rhBMP-2 was observed in the age group level PLIF. There was a 3-fold increase in the rate of PLIF without rhBMP-2 compared to PLIF with rhBMP-2, with both procedures being mainly done in patients less than 65 years of age.

Kinetics of pyridine degradation along with toluene and methylene chloride with Bacillus sp. in packed bed reactor

Energy Technology Data Exchange (ETDEWEB)

Uma, B.; Sandhya, S. [National Environmental Engineering Research Institute, CSIR-Complex, Madras (India)

1998-04-01

Bacillus coagulans strain isolated from contaminated soil was immobilised on activated carbon for degradation of pyridine, toluene and methylene chloride containing synthetic wastewaters. Pyridine was supplied as the only source of nitrogen in the wastewaters. Continuous runs in a packed bed laboratory reactor showed that immobilized B. coagulans can degrade pyridine along with other organics rapidly and the effluent ammonia is also controlled in presence of ``organic carbon``. About 644 mg/l of influent TOC was efficiently degraded (82.85%) at 64.05 mg/l/hr loading. (orig.) With 2 figs., 4 tabs., 15 refs.

Photocatalysis of methylene blue contaminated water using titania fiber doped with silicon

International Nuclear Information System (INIS)

Ugarteche, C.V.; Alves, A.K.; Berutti, F.A.; Bergmann, C.P.

2009-01-01

In this work, titania fibers doped with silicon were synthesized by electro spinning methodology, using titanium propoxide, silicon tetra propoxide and a solution of polyvinylpyrrolidone as precursors. The non-tissue material obtained was characterized by X-ray diffraction to determine the phase and crystallite size, BET method to determine the surface and SEM to analyze the microstructure of the fibers. The photo catalytic activity of the fibers in comparison with the standard TiO 2 Degussa P25 was evaluated using a 20ppm methylene blue solution. The composition containing 30% of silicon kept the anatase phase stable until the heat treatment temperature of 800 deg C. In the other compositions there was a formation of the rutile phase, which is less photoactive. The compositions containing silicon were photo catalytic efficient and some of them were more active that the standard P25. (author)

Plasma temperature during methylene blue/light treatment influences virus inactivation capacity and product quality.

Science.gov (United States)

Gravemann, U; Handke, W; Sumian, C; Alvarez, I; Reichenberg, S; Müller, T H; Seltsam, A

2018-02-27

Photodynamic treatment using methylene blue (MB) and visible light is in routine use for pathogen inactivation of human plasma in different countries. Ambient and product temperature conditions for human plasma during production may vary between production sites. The influence of different temperature conditions on virus inactivation capacity and plasma quality of the THERAFLEX MB-Plasma procedure was investigated in this study. Plasma units equilibrated to 5 ± 2°C, room temperature (22 ± 2°C) or 30 ± 2°C were treated with MB/light and comparatively assessed for the inactivation capacity for three different viruses, concentrations of MB and its photoproducts, activity of various plasma coagulation factors and clotting time. Reduced solubility of the MB pill was observed at 5 ± 2°C. Photocatalytic degradation of MB increased with increasing temperature, and the greatest formation of photoproducts (mainly azure B) occurred at 30 ± 2°C. Inactivation of suid herpesvirus, bovine viral diarrhoea virus and vesicular stomatitis virus was significantly lower at 5 ± 2°C than at higher temperatures. MB/light treatment affected clotting times and the activity of almost all investigated plasma proteins. Factor VIII (-17·7 ± 8·3%, 22 ± 2°C) and fibrinogen (-14·4 ± 16·4%, 22 ± 2°C) showed the highest decreases in activity. Increasing plasma temperatures resulted in greater changes in clotting time and higher losses of plasma coagulation factor activity. Temperature conditions for THERAFLEX MB-Plasma treatment must be carefully controlled to assure uniform quality of pathogen-reduced plasma in routine production. Inactivation of cooled plasma is not recommended. © 2018 International Society of Blood Transfusion.

Apparent discrepancy between single-unit activity and [14C]deoxyglucose labeling in optic tectum of the rattlesnake

International Nuclear Information System (INIS)

Auker, C.R.; Meszler, R.M.; Carpenter, D.O.

1983-01-01

Autoradiographic analysis of [1- 14 C]2-deoxy-D-glucose-6-phosphate ([ 14 C]2-DG-P) accumulation in the rattlesnake brain stem and optic tectum was used in an effort to map infrared and visual neuronal pathways. Visual stimulation with a standard stimulus (a heat lamp) resulted in dense labeling of the superficial layers of the optic tectum. Infrared stimulation resulted in labeling at the first synaptic relay, the lateral descending nucleus of the trigeminal tract, but not at higher levels. Responses of infrared units in one hemitectum and visual units in the other were analyzed. There were no clear differences in the number, maximal density, spread, or rates of accommodation of visual units and infrared units, although the locus of maximal density was more superficial for visual units. In general, infrared units generated a greater number of action potentials. All infrared units responded to onset but they varied greatly in their ability to maintain discharge for the duration of the stimulus. Infrared stimuli generated single, large, triphasic on-responses, whereas visual stimulation generated complex multiphasic and long-lasting on- and off-responses. The major infrared-on peak reached maximal amplitude at greater depths and was larger than the major visual-on peak. Amplitude of the infrared peak fell off more rapidly with distance than did amplitude of the visual peak. These observations are consistent with the view that infrared stimulation is effective in discharging neurons but is not associated with intense synaptic excitation. Our observations suggest that 2-deoxy-D-glucose uptake is not necessarily correlated with the degree of action potential activation of specific neuronal pathways. The amount of [ 14 C]2-DG-P labeling may reflect the metabolic requirements for support of synaptic depolarization as well as that supporting action potentials

The Effects of Single Parenthood on Educational Aspiration: A Comparative Study of Children in the United Kingdom and Hong Kong

Science.gov (United States)

Wang, Miao; Ngai, Steven Sek-Yum

2011-01-01

Using data collected by the Organization for Economic Co-operation and Development's Program for International Student Assessment in 2003, this study examines the gap in the educational aspirations of children from single-parent families and two-parent families in the United Kingdom (UK) and Hong Kong. Consistent with previous research on the…

Regenerable, innovative porous silicon-based polymer-derived ceramics for removal of methylene blue and rhodamine B from textile and environmental waters.

Science.gov (United States)

Bruzzoniti, Maria Concetta; Appendini, Marta; Onida, Barbara; Castiglioni, Michele; Del Bubba, Massimo; Vanzetti, Lia; Jana, Prasanta; Sorarù, Gian Domenico; Rivoira, Luca

2018-04-01

The presence of residual color in treated textile wastewater above the regulation limits is still a critical issue in many textile districts. Innovative, polymer-derived ceramics of the Si-C-O system were here synthesized in order to obtain porous nanocomposite materials where a free carbon phase is dispersed into a silicon carbide/silicon oxycarbide network. The sorbents were comprehensively characterized for the removal of two model water-soluble dyes (i.e., the cation methylene blue and the zwitterion rhodamine B). Adsorption is very rapid and controlled by intra-particle and/or film diffusion, depending on dye concentration. Among the nanocomposites studied, the SiOC aerogel (total capacity about 45 mg/g, is easily regenerated under mild treatment (250 °C, 2 h). Adsorption of dyes is not affected by the matrix composition: removals of 150 mg/L methylene blue from river water and simulated textile wastewater with high content of metal ions (2-50 mg/L) and chemical oxygen demand (800 mg/L) were higher than 92% and quantitative for a dye concentration of 1 mg/L.

The single unit transfusion in post partum hemorrhage: A new perspective.

Science.gov (United States)

Nama, Vivek; Karoshi, Mahantesh; Kakumani, V

2006-01-01

Every year, about 210 million women become pregnant. Postpartum hemorrhage (PPH) is one of the major complications of pregnancy, accounting for 14 million cases annually. Of these, it is estimated that around 140,000 women die, resulting in a case fatality rate of 1%. PPH is defined by WHO as a blood loss > or = 500 mls. Most instances of PPH occur suddenly and without warning even in women without any of the known risks for this condition. If women do not receive timely medical treatment, as is often the case in many parts of the world, death can occur within two hours. The chance of receiving a safe blood transfusion as part of the therapy for PPH varies enormously from country to country, depending on whether a safe blood transfusion program has been set up as a part of the national health policy. The increasing realization of the potential deleterious effects of blood transfusion, including exposure to HIV and other viral agents, has changed the practices that were previously acceptable for the transfusion of blood, as has the recent recognition of specific patients who will benefit from a single unit of blood. In countries with limited resources, where a majority of women have anemia at the onset of their pregnancies, the slightest deviation from normality during labor and/or delivery leading to excessive hemorrhage can put a women's life at risk. In these instances, the patient needs urgent resuscitation, stabilization and transfer to a nearby center. Available blood, preferably typed cross matched and screened for infections, should be given until the patient receives specific treatment. This is especially true in bled- out obstetrics patients, where one unit may make the difference between a near death state and the possibility of slow recovery and survival.

Methylene chloride exposure and carboxyhemoglobin levels in cabinetmakers

Science.gov (United States)

Banjoko, Sunny O.; Sridhar Mynapelli, K. C.; Ogunkola, Isiah O.; Masheyi, Olatunde O.

2007-01-01

Methylene chloride (MeCl2) is a clear colorless volatile sweet smelling lipophilic solvent used as a constituent of wood vanishes and paints. Human exposure is mainly due to inhalation and its biotransformation by the hepatic mixed function oxidases (MFO) leads to formation of carbon monoxide (CO). Simultaneous exposure to MeCl2 and increased ambient CO results in undesirably increased carboxyhemoglobin (COHb) formation, which predisposes to carboxyhemoglobinaemia with the central nervous system as the primary target organ of toxicity. In this study, ambient CO levels were determined using a CO personal monitor in different pasts of Ibadan Nigeria and work place microenvironment of 50 Cabinet makers (test group) and 50 volunteer (control) in non-furniture making occupations. Mann Whitney U and Kruskaal Wallis were the statistical methods of analysis used. Questionnaires were administered to both groups carboxyhaemoglobin levels were determined in venous blood drawn from individuals in the two groups by differential spectrophotometric method. Ambient CO levels in Ibadan were observed to be between 4 and 52 ppm with a mean of 20 ppm. Work environment CO levels were significantly higher in test subjects than controls at 5.2 ± 1.08 ppm and 2.08 ± 0.91 ppm respectively (P 0.05). It is therefore imperative to substitute MeCl2 for safer chemicals in wood vanish and paints and the use of protective gas masks and adequate ventilation should be mandatory whenever MeCl2 is used. PMID:21938216

Nanomolar determination of 4-nitrophenol based on a poly(methylene blue)-modified glassy carbon electrode.

Science.gov (United States)

Giribabu, Krishnamoorthy; Suresh, Ranganathan; Manigandan, Ramadoss; Munusamy, Settu; Kumar, Sivakumar Praveen; Muthamizh, Selvamani; Narayanan, Vengidusamy

2013-10-07

A poly(methylene blue)-modified glassy carbon electrode (PMB/GCE) was fabricated by electropolymerisation of methylene blue on a GCE and further utilized to investigate the electrochemical determination of 4-nitrophenol (4-NP) by cyclic voltammetry (CV), differential pulse voltammetry and chronocoulometry. The morphology of the PMB on GCE was examined using a scanning electron microscope (SEM). An oxidation peak of 4-NP at the PMB modified electrode was observed at 0.28 V, and in the case of bare GCE, no oxidation peak was observed, which indicates that PMB/GCE exhibits a remarkable effect on the electrochemical determination of 4-NP. Due to this remarkable effect of PMB/GCE, a sensitive and simple electrochemical method was proposed for the determination of 4-NP. The effect of the scan rate and pH was investigated to determine the optimum conditions at which the PMB/GCE exhibits a higher sensitivity with a lower detection limit. Moreover, kinetic parameters such as the electron transfer number, proton transfer number and standard heterogeneous rate constant were calculated. Under optimum conditions, the oxidation current of 4-NP is proportional to its concentration in the range of 15-250 nM with a correlation coefficient of 0.9963. The detection limit was found to be 90 nM (S/N = 3). The proposed method based on PMB/GCE is simple, easy and cost effective. To further confirm its possible application, the proposed method was successfully used for the determination of 4-NP in real water samples with recoveries ranging from 97% to 101.6%. The interference due to sodium, potassium, calcium, magnesium, copper, zinc, iron, sulphate, carbonate, chloride, nitrate and phosphate was found to be almost negligible.

Complexing Methylene Blue with Phosphorus Dendrimers to Increase Photodynamic Activity

Directory of Open Access Journals (Sweden)

Monika Dabrzalska

2017-02-01

Full Text Available The efficiency of photodynamic therapy is limited mainly due to low selectivity, unfavorable biodistribution of photosensitizers, and long-lasting skin sensitivity to light. However, drug delivery systems based on nanoparticles may overcome the limitations mentioned above. Among others, dendrimers are particularly attractive as carriers, because of their globular architecture and high loading capacity. The goal of the study was to check whether an anionic phosphorus dendrimer is suitable as a carrier of a photosensitizer—methylene blue (MB. As a biological model, basal cell carcinoma cell lines were used. We checked the influence of the MB complexation on its singlet oxygen production ability using a commercial fluorescence probe. Next, cellular uptake, phototoxicity, reactive oxygen species (ROS generation, and cell death were investigated. The MB-anionic dendrimer complex (MB-1an was found to generate less singlet oxygen; however, the complex showed higher cellular uptake and phototoxicity against basal cell carcinoma cell lines, which was accompanied with enhanced ROS production. Owing to the obtained results, we conclude that the photodynamic activity of MB complexed with an anionic dendrimer is higher than free MB against basal cell carcinoma cell lines.

Fabrication of magnetic carbon composites from peanut shells and its application as a heterogeneous Fenton catalyst in removal of methylene blue

Energy Technology Data Exchange (ETDEWEB)

Zhou, Lincheng, E-mail: zhoulc@lzu.edu.cn; Ma, Junjun; Zhang, He; Shao, Yanming; Li, Yanfeng

2015-01-01

Graphical abstract: Peanut shell magnetic carbon (PMC) were fabricated by carbonized the mixture of peanut shells and (NH{sub 4}){sub 3}Fe(C{sub 2}O{sub 4}){sub 3}. The obtained PMC exhibit high efficiency in catalysis oxidation methylene blue with the help of K{sub 2}S{sub 2}O{sub 8} and it can be easily separated from aqueous by external magnetic field. Meanwhile, the catalyst can be reused for seven times almost without decreased of activity. - Highlights: • Novel peanut shell magnetic carbon (PMC) catalysts were successfully synthesized. • PMC exhibited superior activity as a heterogeneous Fenton-like catalyst. • A high efficient Fenton-like system was set up for removal MB. • PMC posed excellent catalysis oxidation quality, stability and good reusability. - Abstract: Magnetic carbons were prepared from agricultural waste peanut shells and Ferric ammonium oxalate via a simple impregnation and carbonization process. The obtained composites were characterized by element analysis, MÖssbauer spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, X-ray diffraction, vibrating sample magnetometry and the Brunauer-Emmett-Teller surface area method, respectively. The magnetic carbon material was used as catalyst of heterogeneous Fenton reaction to remove methylene blue with the help of persulfate in waste water. The results indicated that both the removal rate and removal efficiency of this catalytic system are very excellent. The degradation efficiency was best (90% within 30 min) using initial concentrations of 0.5 g L{sup −1} persulfate and 40 mg L{sup −1} methylene blue. The removal mechanism was investigated by LC-MS. The catalyst retained its activity after seven reuses, indicating its good stability and reusability. It is inexpensive because it consists mainly of agricultural waste. Its porosity contributed to its high activity, which was achieved without any additional activation process. These indicating that the catalyst is

Equilibrium models and kinetic for the adsorption of methylene blue on Co-hectorites

International Nuclear Information System (INIS)

Ma Jun; Jia Yongzhong; Jing Yan; Sun Jinhe; Yao Ying; Wang Xiaohua

2010-01-01

The adsorption of methylene blue (MB) onto the surface of cobalt doping hectorite (Co-hectorite) was systematically studied. The physical properties of Co-hectorites were investigated, where characterizations were carried out by X-ray diffraction (XRD) and Electron Diffraction Spectrum (EDS) techniques, and morphology was examined by nitrogen adsorption. The sample with a Co content 5% (m/m) had a higher specific surface area than other Co-hectorites. The pore diameters were distributed between 2.5 and 5.0 nm. The adsorption results revealed that Co-hectorite surfaces possessed effective interactions with MB and bases, and greatest adsorption capacity achieved with Co content 5%, where the best-fit isotherm model was the Langmuir adsorption model. Kinetic studies were fitted to the pseudo-second-order kinetic model. The intraparticle diffusion was not the rate-limiting step for the whole reaction.

Nanostructure CdS/ZnO heterojunction configuration for photocatalytic degradation of Methylene blue

Science.gov (United States)

Velanganni, S.; Pravinraj, S.; Immanuel, P.; Thiruneelakandan, R.

2018-04-01

In the present manuscript, thin films of Zinc Oxide (ZnO) have been deposited on a FTO substrate using a simple successive ionic layer adsorption and reaction (SILAR) and chemical bath deposition (CBD) method. Cadmium Sulphide (CdS) nanoparticles are sensitized over ZnO thin films using SILAR method. The synthesized nanostructured CdS/ZnO heterojunction thin films was characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), High resolution transmission electron microscopy (HR-TEM), X-ray photoelectron spectroscopy (XPS), UV-Vis spectroscopy and Raman spectroscopy techniques. The band gap of CdS nanoparticles over ZnO nanostructure was found to be about 3.20 eV. The photocatalytic activities of the deposited CdS/ZnO thin films were evaluated by the degradation of methylene blue (MB) in an aqueous solution under sun light irradiation.

Azure B, a metabolite of methylene blue, is a high-potency, reversible inhibitor of monoamine oxidase

Energy Technology Data Exchange (ETDEWEB)

Petzer, Anél, E-mail: 12264954@nwu.ac.za [Unit for Drug Research and Development, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom, 2520 (South Africa); Harvey, Brian H. [Division of Pharmacology, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom, 2520 (South Africa); Wegener, Gregers [Centre for Psychiatric Research, Aarhus University Hospital-Risskov, Skovagervej 2, 8240 Risskov (Denmark); Petzer, Jacobus P. [Division of Pharmaceutical Chemistry, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom, 2520 (South Africa)

2012-02-01

Methylene blue (MB) has been shown to act at multiple cellular and molecular targets and as a result possesses diverse medical applications. Among these is a high potency reversible inhibition of monoamine oxidase A (MAO-A) that may, at least in part, underlie its adverse effects but also its psycho- and neuromodulatory actions. MB is metabolized to yield N-demethylated products of which azure B, the monodemethyl species, is the major metabolite. Similar to MB, azure B also displays a variety of biological activities and may therefore contribute to the pharmacological profile of MB. Based on these observations, the present study examines the interactions of azure B with recombinant human MAO-A and -B. The results show that azure B is a potent MAO-A inhibitor (IC{sub 50} = 11 nM), approximately 6-fold more potent than is MB (IC{sub 50} = 70 nM) under identical conditions. Measurements of the time-dependency of inhibition suggest that the interaction of azure B with MAO-A is reversible. Azure B also reversibly inhibits the MAO-B isozyme with an IC{sub 50} value of 968 nM. These results suggest that azure B may be a hitherto under recognized contributor to the pharmacology and toxicology of MB by blocking central and peripheral MAO-A activity and as such needs to be considered during its use in humans and animals. Highlights: ► Methylene blue (MB) is a known potent MAO-A inhibitor. ► Azure B, the major metabolite of MB, is more potent as a MAO-A inhibitor. ► Azure B may be a contributor to the CNS pharmacology and toxicology of MB.

Breakdown of methylene blue and methyl orange by pulsed corona discharge

Science.gov (United States)

Grabowski, L. R.; van Veldhuizen, E. M.; Pemen, A. J. M.; Rutgers, W. R.

2007-05-01

The recently developed corona above water technique is applied to water containing 10 mg l-1 methylene blue (MB) or methyl orange (MO). The corona discharge pulses are created with a spark gap switched capacitor followed by a transmission line transformer. The pulse amplitude is 40 kV; its duration is 50 ns. At a pulse repetition rate of 10 Hz this leads to an average power of 0.6 W into the discharge. MB and MO are completely decolourized in ~20 min. This corresponds to a yield of ~4.5 gr kW-1h-1, which is much higher than obtained with other discharge techniques or sonoluminescence. The high yield is reflected in the observed temperature increase of only ~1 K. Tests with additional chemicals show that the initial speed of the conversion can be influenced but the total time required for total decolourization is constant. Further, it follows that the main oxidation path of the dyes is by direct ozone attack and the conversion products are strong acids.

Breakdown of methylene blue and methyl orange by pulsed corona discharge

Energy Technology Data Exchange (ETDEWEB)

Grabowski, L R [Department of Applied Physics, Technische Universiteit Eindhoven (Netherlands); Veldhuizen, E M van [Department of Applied Physics, Technische Universiteit Eindhoven (Netherlands); Pemen, A J M [Department of Electrical Engineering, Technische Universiteit Eindhoven (Netherlands); Rutgers, W R [Department of Applied Physics, Technische Universiteit Eindhoven (Netherlands)

2007-05-15

The recently developed corona above water technique is applied to water containing 10 mg l{sup -1} methylene blue (MB) or methyl orange (MO). The corona discharge pulses are created with a spark gap switched capacitor followed by a transmission line transformer. The pulse amplitude is 40 kV; its duration is 50 ns. At a pulse repetition rate of 10 Hz this leads to an average power of 0.6 W into the discharge. MB and MO are completely decolourized in {approx}20 min. This corresponds to a yield of {approx}4.5 gr kW{sup -1}h{sup -1}, which is much higher than obtained with other discharge techniques or sonoluminescence. The high yield is reflected in the observed temperature increase of only {approx}1 K. Tests with additional chemicals show that the initial speed of the conversion can be influenced but the total time required for total decolourization is constant. Further, it follows that the main oxidation path of the dyes is by direct ozone attack and the conversion products are strong acids.

Breakdown of methylene blue and methyl orange by pulsed corona discharge

International Nuclear Information System (INIS)

Grabowski, L R; Veldhuizen, E M van; Pemen, A J M; Rutgers, W R

2007-01-01

The recently developed corona above water technique is applied to water containing 10 mg l -1 methylene blue (MB) or methyl orange (MO). The corona discharge pulses are created with a spark gap switched capacitor followed by a transmission line transformer. The pulse amplitude is 40 kV; its duration is 50 ns. At a pulse repetition rate of 10 Hz this leads to an average power of 0.6 W into the discharge. MB and MO are completely decolourized in ∼20 min. This corresponds to a yield of ∼4.5 gr kW -1 h -1 , which is much higher than obtained with other discharge techniques or sonoluminescence. The high yield is reflected in the observed temperature increase of only ∼1 K. Tests with additional chemicals show that the initial speed of the conversion can be influenced but the total time required for total decolourization is constant. Further, it follows that the main oxidation path of the dyes is by direct ozone attack and the conversion products are strong acids

Criticality safety validation: Simple geometry, single unit {sup 233}U systems

Energy Technology Data Exchange (ETDEWEB)

Putman, V.L.

1997-06-01

Typically used LMITCO criticality safety computational methods are evaluated for suitability when applied to INEEL {sup 233}U systems which reasonably can be modeled as simple-geometry, single-unit systems. Sixty-seven critical experiments of uranium highly enriched in {sup 233}U, including 57 aqueous solution, thermal-energy systems and 10 metal, fast-energy systems, were modeled. These experiments include 41 cylindrical and 26 spherical cores, and 41 reflected and 26 unreflected systems. No experiments were found for intermediate-neutron-energy ranges, or with interstitial non-hydrogenous materials typical of waste systems, mixed {sup 233}U and plutonium, or reflectors such as steel, lead, or concrete. No simple geometry experiments were found with cubic or annular cores, or approximating infinite sea systems. Calculations were performed with various tools and methodologies. Nine cross-section libraries, based on ENDF/B-IV, -V, or -VI.2, or on Hansen-Roach source data, were used with cross-section processing methods of MCNP or SCALE. The k{sub eff} calculations were performed with neutral-particle transport and Monte Carlo methods of criticality codes DANT, MCNP 4A, and KENO Va.

Oxygen Vacancy-Mediated ZnO Nanoparticle Photocatalyst for Degradation of Methylene Blue

Directory of Open Access Journals (Sweden)

Qiuping Zhang

2018-02-01

Full Text Available ZnO nanoparticles (NPs are synthesized by deoxidizing ZnO powder in a vacuum drying process. This process reduces the size of the NPs and increases the concentration of oxygen vacancies on their surfaces. ZnO NPs with sufficient oxygen vacancies are highly effective for the photodecomposition of methylene blue (MB dye in water under ultraviolet irradiation. The MB degradation efficiency exceeds 99 percent after 50 min of light irradiation, and the catalytic property of the NPs remains stable over several complete degradation cycles. It is revealed that the concentration of oxygen vacancies on the surface, and the photocatalytic activity, are both higher for smaller NPs. Oxygen vacancies reduce the recombination rate of photo-generated charge carriers by capturing the electrons and hence, improve the efficiency of redox reactions. In addition, a smaller particle size leads to a larger specific surface area and a higher photonic efficiency for the ZnO NPs.

The hybrid methylene blue-zeolite system: a higher efficient photo catalyst for photo inactivation of pathogenic microorganisms

International Nuclear Information System (INIS)

Smolinska, M.; Cik, G.; Sersen, F.; Caplovicova, M.; Takacova, A.; Kopani, M.

2015-01-01

The composite system can be prepared by incorporation of methylene blue into the channels of zeolite and by adsorption on the surface of the crystals. The composite photo sensitizer effectively absorbs the red light (kmax = 648 nm) and upon illumination with light-emitting diode at a fluence rate of 1.02 mW cm-2 generates effectively reactive singlet oxygen in aqueous solution, which was proved by EPR spectroscopy. To test efficiency for inactivation of pathogenic microorganisms, we measured photo killing of bacteria Escherichia coli and Staphylococcus aureus and yeasts Candida albicans. We found out that after the microorganisms have been adsorbed at the surface of such modified zeolite, the photo generated singlet oxygen quickly penetrates their cell walls, bringing about their effective photo inactivation. The growth inhibition reached almost 50 % at 200 and 400 mg modified zeolite in 1 ml of medium in E. coli and C. albicans, respectively. On the other hand, the growth inhibition of S. aureus reached 50 % at far smaller amount of photo catalyst (30 lg per 1 ml of medium). These results demonstrate differences in sensitivities of bacteria and yeast growth. The comparison revealed that concentration required for IC50 was in case of C. albicans several orders of magnitude lower for a zeolite-immobilized dye than it was for a freely dissolved dye. In S. aureus, this concentration was even lower by four orders of magnitude. Thus, our work suggested a new possibility to exploitation of zeolite and methylene blue in the protection of biologically contaminated environment, and in photodynamic therapy.

Automatic regulation of the feedwater turbo-pump capacity for the single-turbine 1000 MW NPP unit

International Nuclear Information System (INIS)

Pavlysh, O.N.; Garbuzov, I.P.; Reukov, Yu.N.

1985-01-01

A schematic of the flow regulators (FR) of feedwater turbo-pumps (FTP) for the single-turbine 1000 MW NPP unit is presented. The FR operate in response to feedwoter signals from FTP or in response to FTP rotor rotational speed and control automatic speed governars. The FR automatic regulation ensures limitation of FTP rotor maximum rotational speed at a feedwater flow rate excess equal to 3600 T/h. The transients in the automatic regulation system are considered. Production tests of FTP FR confirmed the FR operation reliability and the right choice of the regulator concept and structure

Performance of zeolite ceramic membrane synthesized by wet mixing method as methylene blue dye wastewater filter

Science.gov (United States)

Masturi; Widodo, R. D.; Edie, S. S.; Amri, U.; Sidiq, A. L.; Alighiri, D.; Wulandari, N. A.; Susilawati; Amanah, S. N.

2018-03-01

Problem of pollution in water continues in Indonesia, with its manufacturing sector as biggest contributor to economic growth. One out of many technological solutions is post-treating industrial wastewater by membrane filtering technology. We presented a result of our fabrication of ceramic membrane made from zeolite with simple mixing and he. At 5% of (poring agent):(total weight), its permeability stays around 2.8 mD (10‑14m2) with slight variance around it, attributed to the mixture being in far below percolating threshold. All our membranes achieve remarkable above 90% rejection rate of methylene blue as solute waste in water solvent.

Phosphorus dendrimers and photodynamic therapy. Spectroscopic studies on two dendrimer-photosensitizer complexes: Cationic phosphorus dendrimer with rose bengal and anionic phosphorus dendrimer with methylene blue.

Science.gov (United States)

Dabrzalska, Monika; Zablocka, Maria; Mignani, Serge; Majoral, Jean Pierre; Klajnert-Maculewicz, Barbara

2015-08-15

Dendrimers due to their unique architecture may play an important role in drug delivery systems including chemotherapy, gene therapy and recently, photodynamic therapy as well. We investigated two dendrimer-photosensitizer systems in context of potential use of these systems in photodynamic therapy. The mixtures of an anionic phosphorus dendrimer of the second generation and methylene blue were studied by UV-vis spectroscopy while that of a cationic phosphorus dendrimer (third generation) and rose bengal were investigated by spectrofluorimetric methods. Spectroscopic analysis of these two systems revealed the formation of dendrimer-photosensitizer complexes via electrostatic interactions as well as π stacking. The stoichiometry of the rose bengal-cationic dendrimer complex was estimated to be 7:1 and 9:1 for the methylene blue-anionic dendrimer complex. The results suggest that these polyanionic or polycationic phosphorus dendrimers can be promising candidates as carriers in photodynamic therapy. Copyright © 2015 Elsevier B.V. All rights reserved.

The interactions of azure B, a metabolite of methylene blue, with acetylcholinesterase and butyrylcholinesterase

International Nuclear Information System (INIS)

Petzer, Anél; Harvey, Brian H.; Petzer, Jacobus P.

2014-01-01

Methylene blue (MB) is reported to possess diverse pharmacological actions and is attracting increasing attention for the treatment of neurodegenerative disorders such as Alzheimer's disease. Among the pharmacological actions of MB, is the significant inhibition of acetylcholinesterase (AChE) and butyrylcholinesterase (BuChE). These activities may, at least in part, underlie MB's beneficial effects in Alzheimer's disease. MB is metabolized to yield N-demethylated products of which azure B, the monodemethyl metabolite, is the predominant species. Azure B has been shown to be pharmacologically active and also possesses a variety of biological actions. Azure B therefore may contribute to the pharmacological profile of MB. Based on these considerations, the present study investigates the possibility that azure B may, similar to MB, act as an inhibitor of human AChE and BuChE. The results document that azure B inhibits AChE and BuChE with IC 50 values of 0.486 μM and 1.99 μM, respectively. The results further show that azure B inhibits AChE and BuChE reversibly, and that the modes of inhibition are most likely competitive. Although the AChE and BuChE inhibitory activities of azure B are twofold and fivefold, respectively, less potent than those recorded for MB [IC 50 (AChE) = 0.214 μM; IC 50 (BuChE) = 0.389 μM] under identical conditions, azure B may be a contributor to MB's in vivo activation of the cholinergic system and beneficial effects in Alzheimer's disease. - Highlights: • Methylene blue (MB) is a known inhibitor of AChE and BuChE. • Azure B, the major metabolite of MB, also is an inhibitor of AChE and BuChE. • Azure B may be a contributor to MB's in vivo activation of the cholinergic system. • Azure B may contribute to MB's potential in Alzheimer's disease therapy

Dengue and chikungunya viruses in plasma are effectively inactivated after treatment with methylene blue and visible light.

Science.gov (United States)

Fryk, Jesse J; Marks, Denese C; Hobson-Peters, Jody; Prow, Natalie A; Watterson, Daniel; Hall, Roy A; Young, Paul R; Reichenberg, Stefan; Sumian, Chryslain; Faddy, Helen M

2016-09-01

Arboviruses, such as dengue viruses (DENV) and chikungunya virus (CHIKV), pose a risk to the safe transfusion of blood components, including plasma. Pathogen inactivation is an approach to manage this transfusion transmission risk, with a number of techniques being used worldwide for the treatment of plasma. In this study, the efficacy of the THERAFLEX MB-Plasma system to inactivate all DENV serotypes (DENV-1, DENV-2, DENV-3, DENV-4) or CHIKV in plasma, using methylene blue and light illumination at 630 nm, was investigated. Pooled plasma units were spiked with DENV-1, DENV-2, DENV-3 DENV-4, or CHIKV and treated with the THERAFLEX MB-Plasma system at four light illumination doses: 20, 40, 60, and 120 (standard dose) J/cm(2) . Pre- and posttreatment samples were collected and viral infectivity was determined. The reduction in viral infectivity was calculated for each dose. Treatment of plasma with the THERAFLEX MB-Plasma system resulted in at least a 4.46-log reduction in all DENV serotypes and CHIKV infectious virus. The residual infectivity for each was at the detection limit of the assay used at 60 J/cm(2) , with dose dependency also observed. Our study demonstrated the THERAFLEX MB-Plasma system can reduce the infectivity of all DENV serotypes and CHIKV spiked into plasma to the detection limit of the assay used at half of the standard illumination dose. This suggests this system has the capacity to be an effective option for managing the risk of DENV or CHIKV transfusion transmission in plasma. © 2016 AABB.

Removal of methylene blue by adsorption onto activated carbon developed from Ficus carica bast

Directory of Open Access Journals (Sweden)

Deepak Pathania

2017-02-01

Full Text Available In this study, activated carbon was developed from Ficus carica bast (FCBAC. The experiments were carried out to explore methylene blue (MB uptake by FCBAC. The influence of various experimental factors such as contact time, initial dye concentration, adsorbent dosage, temperature and pH of dye solution was investigated. The adsorption equilibrium was represented with Langmuir, Freundlich and Temkin isotherm models. Langmuir and Tempkin equations were found to have the correlation coefficient value in good agreement. Adsorption of MB onto FCBAC followed pseudo second order kinetics. The calculated values of ΔH°, ΔS° and ΔG° were found to be 21.55 kJ/mol, 76.24 J/mol K and −1.55 kJ/mol, respectably. Adsorption process was spontaneous and endothermic in nature.

Visible-light photocatalytic degradation of methylene blue with laser-induced Ag/ZnO nanoparticles

International Nuclear Information System (INIS)

Whang, Thou-Jen; Hsieh, Mu-Tao; Chen, Huang-Han

2012-01-01

The preparation of Ag doped ZnO nanoparticles conducted through the method of laser-induction is presented in this work. The Ag/ZnO nanoparticles attained from various weight percentages of added AgNO 3 relative to ZnO were applied under visible-light irradiation for evaluating the heterogeneous photocatalytic degradations of methylene blue (MB) solutions. It was shown that the catalytic behavior of Ag/ZnO nanoparticles in the visible-light range is notably improved through the Ag deposition onto ZnO nanoparticles by the method of laser-induction with a maximum effectiveness of 92% degradation. The properties of the nanoparticles were characterized by the employments of UV-vis spectroscopy (UV-vis), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), and selected-area electron diffraction (SAED).

Complexes between lanthanide (III) and yttrium (III) picrates and tetra methylene sulfoxide as ligand

International Nuclear Information System (INIS)

Silva, M.A.A. da.

1991-01-01

The preparation and characterization of addition compounds between lanthanide (III) and yttrium (III) picrates and tetra methylene sulfoxide as ligand were described. The adducts were prepared in the molar relation 1 (salt): 3(ligand) in ethanol. They are microcrystalline with more intense color than those of their respective hydrated salts. At room temperature conditions they are non hygroscopic and do not present perceptible alterations. They became slightly opalescent, when heated between 363 and 423 K. At higher temperatures under several heating ratios, the behavior shown is the same: melting between 439 and 472 K. The characterization of the compounds was made by elemental analysis, electrolytic conductance measurements, X-ray powder patterns, infrared spectroscopy, visible electronic absorption and emission spectra of the neodymium (III) and europium (III), respectively. (author). 116 refs., 17 tabs., 11 figs

Methylene blue adsorption in clay mineral dealt with organic cation; Sorcao de azul de metileno em argila esmectitica tratada com cation organico

Energy Technology Data Exchange (ETDEWEB)

Silva, T.L. [Universidade Federal do Para (UFPA), Maraba, PA (Brazil). Faculdade de Engenharia de Materiais; Lemos, V.P., E-mail: tls1981@hotmail.com [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Centro de Geociencias

2011-07-01

The interaction among organic cations, as the methylene blue (AM) and benzyltrimethylammonium (BTMA), and clay minerals of the group of the smectite they result in the formation of applied materials in the adsorption of organic pollutant presents in waters, soils and you cultivate. In this work they were prepared the adsorbents (organic-clays) smectite - AM and smectite-BTMA. The precursory sample of smectite was collected in Rio Branco-Acre. We were also used an smectite sample collected in Sena Madureira (SM)-Acre already characterized in previous work and a sample of standard smectite Swy-2-Na-Montmorillonite (SWy-2) of Wymong - USA. The organic agents selected for this study they were: Blue of Methylene, denominated AM and Benzyltrimethylammonium, denominated BTMA. They were appraised the capacities adsorptive of the treated samples with BTMA being used AM as adsorbate. The results of these evaluations detected that ran total adsorption of AM (concentrations varying from 1 to 10 ppm) for the treated samples with BTMA. The organic cation, BTMA, interacting with the surfaces of the natural clay was more efficient in the adsorption of AM than the clay without the previous treatment with this salt. (author)

Photocatalytic degradation of methylene blue on magnetically separable MgFe2O4 under visible light irradiation

International Nuclear Information System (INIS)

Shahid, Muhammad; Jingling, Liu; Ali, Zahid; Shakir, Imran; Warsi, Muhammad Farooq; Parveen, Riffat; Nadeem, Muhammad

2013-01-01

A magnetically separable single-phase MgFe 2 O 4 photocatalyst with a spinel crystal structure was synthesized by using the solid-state reaction method. The formation of spinel structure is confirmed by X-ray diffraction and Fourier transform infrared spectroscopy. The magnetic measurements showed that the photocatalyst material can be separated from water when an external magnetic field is added and redispersed into water solution after the external magnetic field is eliminated. It is one of the promising photocatalysts for waste water treatment. The photocatalytic activity of MgFe 2 O 4 was investigated by using the photo-decomposition of methylene blue dye under visible light. The photoelectrochemical property of the MgFe 2 O 4 was studied by measuring their photocurrent–potential behavior in 1 M NaOH electrolyte under AM 1.5100 mW cm −2 illumination. - Graphical abstract: Highly efficient magnetically separable MgFe 2 O 4 photocatalyst for organic based impurities decomposition as well as for the production of H 2 gas was synthesized and characterized successfully (a) MgFe 2 O 4 photocatalyst in polluted water, (b) The photocatalyst (MgFe 2 O 4 ) is being attracted toward magnetic field for separation, (c) Hysteresis loop of MgFe 2 O 4 showing magnetic behavior. Highlights: ► New photocatalyst working in the visible range have been synthesized by facile cheap route. ► MgFe 2 O 4 photocatalyst showed well defined magnetically separable behavior. ► Excellent water splitting characteristics to produce H 2 was observed under visible light irradiation

Synthesis of 4-Methylene-2-cyclohexenones and Their Aromatization Reaction toward para-Methoxylmethyl Anisole Derivatives

International Nuclear Information System (INIS)

Lee, Jeong Mi; Lee, Ka Young; Kim, Jae Nyoung

2004-01-01

We and other groups have reported the selective introduction of nucleophiles at the secondary benzylic position of the Baylis-Hillman acetates via the corresponding DABCO salts. Thus, we envisioned that we could prepare 4-methylene- 2-cyclohexenone skeleton and para-methoxymethyl anisoles by combining the DABCO salt concept and the aromatization reaction with iodine in methanol. Suitably substituted anisoles are useful as the starting materials for the fragrances, dyes and pesticides, as antioxidants in oils and fats, or as stabilizers of plastics. Moreover, paramethoxymethyl anisoles have been used for the kinetic acetalization of diol or amino alcohol systems in the presence of DDQ5 during the synthesis of (+)-FR900482, taxotere side chain,5c cyclopropyl lactone oxylipins, and erythromycin A.

Sensitive flotation-spectrophotometric determination of gold, based on the gold(I)-iodide-methylene blue system.

Science.gov (United States)

Marczenko, Z; Jankowski, K

1985-04-01

The gold(I)-iodide-Methylene Blue (MB) system is suitable for flotation separation and spectrophotometric determination of gold. Under the optimum conditions [(MB(+))(AuI(2)(-))].3[(MB(+))(I(3)(-))] is formed, and floated with cyclohexane. The product is dissolved in methanol and its absorbance measured. The molar absorptivity is 3.4 x 10(5)1.mole(-1).cm(-1) at 655 nm. The proposed method is more than three times as sensitive as the Rhodamine B method. Pt, Pd, Ag and Hg interfere seriously, and Ir, Rh, Bi and Cd to a smaller extent. Preliminary separation of gold by precipitation with tellurium as a collector is recommended. The method has been applied to determination of gold traces (about 1 x 10(-4)%) in a copper sample.

United States housing, 2012

Science.gov (United States)

Delton Alderman

2013-01-01

Provides current and historical information on housing market in the United States. Information includes trends for housing permits and starts, housing completions for single and multifamily units, and sales and construction. This report will be updated annually.

METRIC context unit architecture

Energy Technology Data Exchange (ETDEWEB)

Simpson, R.O.

1988-01-01

METRIC is an architecture for a simple but powerful Reduced Instruction Set Computer (RISC). Its speed comes from the simultaneous processing of several instruction streams, with instructions from the various streams being dispatched into METRIC's execution pipeline as they become available for execution. The pipeline is thus kept full, with a mix of instructions for several contexts in execution at the same time. True parallel programming is supported within a single execution unit, the METRIC Context Unit. METRIC's architecture provides for expansion through the addition of multiple Context Units and of specialized Functional Units. The architecture thus spans a range of size and performance from a single-chip microcomputer up through large and powerful multiprocessors. This research concentrates on the specification of the METRIC Context Unit at the architectural level. Performance tradeoffs made during METRIC's design are discussed, and projections of METRIC's performance are made based on simulation studies.

Diffusion of single Au, Ag and Cu atoms inside Si(111)-(7 × 7) half unit cells: A comparative study

Energy Technology Data Exchange (ETDEWEB)

Liu, Qin [Department of Physics, Southern University of Science and Technology, Shenzhen, Guangdong 518055 (China); Department of Physics, The Chinese University of Hong Kong, Shatin, New Territory, Hong Kong (China); Science and Technology on Surface Physics and Chemistry Laboratory, Mianyang, Sichuan 621908 (China); Fu, Qiang [Institut für Physik and IRIS Adlershof, Humboldt-Universität zu Berlin, Zum Großen Windkanal 6, 12489 Berlin (Germany); Shao, Xiji; Ma, Xuhang; Wu, Xuefeng [Department of Physics, Southern University of Science and Technology, Shenzhen, Guangdong 518055 (China); Wang, Kedong, E-mail: wangkd@sustc.edu.cn [Department of Physics, Southern University of Science and Technology, Shenzhen, Guangdong 518055 (China); Xiao, Xudong, E-mail: xdxiao@phy.cuhk.edu.hk [Department of Physics, The Chinese University of Hong Kong, Shatin, New Territory, Hong Kong (China)

2017-04-15

Highlights: • Diffusions of Au, Ag and Cu atoms in the half unit cells of Si(111)-(7×7) have been studied by using a STM-based I-t method. • Despite their similar absorption sites, the diffusion dynamics show obvious differences between Ag and the other two. • Theoretical calculations suggest that different potential energy profiles are responsible for the observed differences. - Abstract: The diffusion behaviors of single Au, Ag and Cu atoms on Si(111)-(7 × 7) half unit cells have been investigated via combining scanning tunneling microscopy and first-principles calculations. Despite the similar adsorption sites between both half unit cells among these elements, the diffusion dynamics show obvious differences between Ag and the other two. Although obvious asymmetry has been found in the diffusion behaviors of Au and Cu atoms in two half unit cells of Si(111)-(7 × 7), the asymmetry behaves in a way different from that of Ag atoms and no dual-time character has been observed for the diffusions of Au and Cu in both half unit cells. Theoretical calculations suggest a different potential energy profile caused by the stronger hybridization between d states of Au (Cu) and Si states make the concept of basin useless for the diffusion of Au and Cu atoms inside the half unit cells of Si(111)-(7 × 7).

A Single Electrochemical Probe Used for Analysis of Multiple Nucleic Acid Sequences

Science.gov (United States)

Mills, Dawn M.; Calvo-Marzal, Percy; Pinzon, Jeffer M.; Armas, Stephanie; Kolpashchikov, Dmitry M.; Chumbimuni-Torres, Karin Y.

2017-01-01

Electrochemical hybridization sensors have been explored extensively for analysis of specific nucleic acids. However, commercialization of the platform is hindered by the need for attachment of separate oligonucleotide probes complementary to a RNA or DNA target to an electrode’s surface. Here we demonstrate that a single probe can be used to analyze several nucleic acid targets with high selectivity and low cost. The universal electrochemical four-way junction (4J)-forming (UE4J) sensor consists of a universal DNA stem-loop (USL) probe attached to the electrode’s surface and two adaptor strands (m and f) which hybridize to the USL probe and the analyte to form a 4J associate. The m adaptor strand was conjugated with a methylene blue redox marker for signal ON sensing and monitored using square wave voltammetry. We demonstrated that a single sensor can be used for detection of several different DNA/RNA sequences and can be regenerated in 30 seconds by a simple water rinse. The UE4J sensor enables a high selectivity by recognition of a single base substitution, even at room temperature. The UE4J sensor opens a venue for a re-useable universal platform that can be adopted at low cost for the analysis of DNA or RNA targets. PMID:29371782

An electrochemical aptasensor for chiral peptide detection using layer-by-layer assembly of polyelectrolyte-methylene blue/polyelectrolyte-graphene multilayer

International Nuclear Information System (INIS)

Qin Haixia; Liu Jiyang; Chen Chaogui; Wang Jiahi; Wang Erkang

2012-01-01

Highlights: ► An electrochemical aptasensor for selective detection of peptide is constructed. ► This aptasensor is based on grapheme multilayer via layer-by-layer assembly. ► Such multilayer facilitates electron transfer and provides more adsorption sites. - Abstract: Here we demonstrate for the first time that by physically adsorbing aptamer onto conductive film assembled via alternate adsorption of graphene/polyelectrolyte and methylene blue/polyelectrolyte, a label-free electrochemical aptasensor with high sensitivity and selectivity for peptide detection is constructed. Graphene multilayer derived from layer-by-layer assembly has played significant roles in this sensing strategy: allowing accumulation of methylene blue, facilitating electron transfer and providing much more adsorption site. As compared to previous electrochemical aptasensors, the current sensor based on graphene multilayer alternated with electroactive molecule layer offers extremely high capability for sensitive detection of target without interference of environmental surrounding. This electroactive probe-confined graphene multilayer confers great flexibility to combine with differential pulse voltammetry (DPV) together. In the presence of target D entiomer of arginine vasopressin (D-VP), the binding of peptide to aptamer block the electron transfer process of MB, leading to decreased current peak of DPV. By this way, this electrochemical aptasensor based on electroactive molecule-intercalated graphene multilayer provide highly sensitive and specific detection of D-VP with the lowest detectable concentration of 1 ng mL −1 and a wide detection range from 1 to 265 ng mL −1 .

Investigation on effect of methylene spacer in holographic grating formation in eosin containing polymethacrylates

Energy Technology Data Exchange (ETDEWEB)

Manickasundaram, S. [Department of Chemistry, Anna University, Sardar Vallabai Patel Road, Chennai 600025 (India); Kannan, P. [Department of Chemistry, Anna University, Sardar Vallabai Patel Road, Chennai 600025 (India)]. E-mail: pakannan@annauniv.edu; Deepa, S. [Centre for Laser Technology, Department of Physics, Anna University, Chennai 600025 (India); Palanisamy, P.K. [Centre for Laser Technology, Department of Physics, Anna University, Chennai 600025 (India)

2007-01-15

A new series of eosin dye based poly(alkyloxymethacrylate)s was synthesized with an even number of side-chain methylene spacers by a free radical addition polymerization method for holographic optical data storage applications. These polymers were characterized by UV, IR and {sup 1}H NMR spectroscopy. The glass transition temperature and thermal stability of the polymers were investigated by DSC and TGA, respectively. As the spacer length increases in the side-chain, Tg, Tm and thermal stability of the polymers decrease, while a reverse trend was observed with film forming ability of the polymers. The optical characterization of the polymers was investigated by forming holographic grating using an Argon ion laser. The grating diffraction efficiency was found to depend not only on the concentration of polymeric film but also on the spacer length of the polymers.

Investigation on effect of methylene spacer in holographic grating formation in eosin containing polymethacrylates

International Nuclear Information System (INIS)

Manickasundaram, S.; Kannan, P.; Deepa, S.; Palanisamy, P.K.

2007-01-01

A new series of eosin dye based poly(alkyloxymethacrylate)s was synthesized with an even number of side-chain methylene spacers by a free radical addition polymerization method for holographic optical data storage applications. These polymers were characterized by UV, IR and 1 H NMR spectroscopy. The glass transition temperature and thermal stability of the polymers were investigated by DSC and TGA, respectively. As the spacer length increases in the side-chain, Tg, Tm and thermal stability of the polymers decrease, while a reverse trend was observed with film forming ability of the polymers. The optical characterization of the polymers was investigated by forming holographic grating using an Argon ion laser. The grating diffraction efficiency was found to depend not only on the concentration of polymeric film but also on the spacer length of the polymers

3,3′-Di-tert-butyl-1,1′-[1,3-phenylenebis(methylene]diurea

Directory of Open Access Journals (Sweden)

Md. Alamgir Hossain

2010-03-01

Full Text Available The title compound, C18H30N4O2, contains two tert-butyl urea groups, each connected to a benzene ring though a methylene group. One of the groups occupies a position almost normal to the aromatic plane with a C—N—C—C torsion angle of −94.4 (4°, while the other is considerably twisted from the ring with a C—N—C—C torsion angle of −136.1 (4°. In the crystal, pairs of molecules are connected to each other, forming centrosymmetric dimers in which two NH groups of one molecule act as hydrogen-bond donors to one carbonyl O atom of the other molecule. The dimers are linked into sheets parallel to (100 by N—H...O hydrogen bonds involving the remaining N—H and C=O groups.

Graphene hydrogels with embedded metal nanoparticles as efficient catalysts in 4-nitrophenol reduction and methylene blue decolorization

Directory of Open Access Journals (Sweden)

Żelechowska Kamila

2016-12-01

Full Text Available Synthesis and characterization of the graphene hydrogels with three different metallic nanoparticles, that is Au, Ag and Cu, respectively is presented. Synthesized in a one-pot approach graphene hydrogels with embedded metallic nanoparticles were tested as heterogeneous catalysts in a model reaction of 4-nitrophenol reduction. The highest activity was obtained for graphene hydrogel with Cu nanoparticles and additional reaction of methylene blued degradation was evaluated using this system. The obtained outstanding catalytic activity arises from the synergistic effect of graphene and metallic nanoparticles. The hydrogel form of the catalyst benefits in the easiness in separation from the reaction mixture (for example using tweezers and reusability.

β-Peptoid "Foldamers" - Why the Additional Methylene Unit?

DEFF Research Database (Denmark)

Olsen, Christian Adam

2011-01-01

adopted and three-dimensional folding of these peptide mimics have been undertaken. The same is true for β-peptides (i.e., oligomers composed of beta-amino acids). Since the first publication describing peptide mimics combining these two structural modifications [the N-alkyl-beta-alanines (β......-peptoids)] in 1998, on the other hand, the application of this backbone construct has appeared much more sparsely in the literature. The present perspective article will provide an overview of the data obtained for beta-peptoid-containing peptide mimics as well as a discussion of the future challenges associated...

The correlation between structural properties, geometrical features, and photoactivity of freestanding TiO2 nanotubes in comparative degradation of 2,4-dichlorophenol and methylene blue

Science.gov (United States)

Vahabzadeh Pasikhani, Javad; Gilani, Neda; Ebrahimian Pirbazari, Azadeh

2018-02-01

Freestanding TiO2 nanotubes (FSNTs) with various physical dimensions were fabricated by two-step anodization process with different voltages and anodization times. The detachment method employed in this study involved voltage reduction at the end of the second step and ultrasonic chemical treatment. The results demonstrated that this detachment method is a beneficial technique to create thin open-mouthed and closed-end FSNTs (with lengths of 6-14 μm). Moreover, the influences of anodization conditions on photocatalytic activity, structural properties and geometrical features of FSNTs in comparative degradation of two non-colored (2,4-dichlorophenol) and colored (methylene blue) pollutants were investigated. Findings revealed that the quantity of the photocatalyst utilized is an effective parameter and using the optimum weight (10 mg/100 ml of 2,4-dichlorophenol) could increase the efficiency of the process up to 21%. Further, the results demonstrated that if equal optimum weights of FSNTs are chosen, decreases in voltage and anodization time significantly influence the structural properties, geometrical features, and photodegradation efficiency. The enhancement achieved in the degradation of both 2,4-dichlorophenol and methylene blue using the nanotubes with the shortest diameter (54 nm) and length (6.5 μm), which possess the lowest porosity (0.5) and also the highest surface area (0.53 m2 g-1), nanotubes’ density (19 cm2 cm-2) and wall thickness to length ratio (2). In addition, the results obtained indicated that the degradation reactions follow first-order kinetics in the degradation of the both pollutants. The apparent degradation rate constant of methylene blue was approximately 1.2 times greater than of the 2,4-dichlorophenol due to the negative charge of the nanotubes’ surface and electrostatic adsorptions.

Removal of methylene blue and rhodamine B from water by zirconium oxide/graphene

Directory of Open Access Journals (Sweden)

Sumita Rani

2016-04-01

Full Text Available Methylene blue (MB and rhodamine B dyes (RB were degraded from water using zirconium oxide (ZrO2 and zirconium oxide/graphene composites (ZrO2/GR as photocatalyst. The photocatalytic efficiency was calculated from absorption spectra obtained using UV–visible spectroscopy. It has been observed that photodegradation time as well as photocatalytic efficiency increase with the concentration of catalyst up to a certain limit after which effect was reversed. The degradation was studied as a function of pH also. It was found that photocatalytic efficiency was more in alkaline medium than acidic medium. Degradation of RB takes place at higher value of pH as compared to MB. The degradation time for MB was 1 h using ZrO2 which get reduced to 32 min using ZrO2/GR composite and for RB it reduced to 40 min (using ZrO2/GR from 80 min (ZrO2.

First Study of Poly(3-Methylene-2-Pyrrolidone) as a Kinetic Hydrate Inhibitor

DEFF Research Database (Denmark)

Abrahamsen, Eirin; Heyns, Ingrid Marié; von Solms, Nicolas

2017-01-01

Formation of gas hydrates is a problem in the petroleum industry where the gas hydrates can cause blockage of the flowlines. Kinetic hydrate inhibitors (KHIs) are water-soluble polymers, sometimes used in combination synergistically or with non-polymeric synergists, that are used to prevent gas h...... are preferable in KHI polymers as long as they are water-soluble at hydrate-forming temperatures.......Formation of gas hydrates is a problem in the petroleum industry where the gas hydrates can cause blockage of the flowlines. Kinetic hydrate inhibitors (KHIs) are water-soluble polymers, sometimes used in combination synergistically or with non-polymeric synergists, that are used to prevent gas...... hydrate blockages. They have been used in the field successfully since 1995. In this paper, we present the first KHI results for the polymer, poly(3-methylene-2-pyrrolidone) (P(3M2P)), which is structurally similar to poly(N-vinylpyrrolidone) (PVP), one of the first KHIs to be discovered. 3M2P polymers...

Reversal by methylene blue of tetanic fade induced in cats by nitric oxide

Directory of Open Access Journals (Sweden)

C.R. Ambiel

1998-03-01

Full Text Available Previous data from our laboratory have indicated that nitric oxide (NO acting at the presynaptic level increases the amplitude of muscular contraction (AMC of the phrenic-diaphragm preparations isolated from indirectly stimulated rats, but, by acting at the postsynaptic level, it reduces the AMC when the preparations are directly stimulated. In the present study we investigated the effects induced by NO when tetanic frequencies of stimulation were applied to in vivo preparations (sciatic nerve-anterior tibial muscle of the cat. Intra-arterial injection of NO (0.75-1.5 mg/kg induced a dose-dependent increase in the Wedensky inhibition produced by high frequencies of stimulation applied to the motor nerve. Intra-arterial administration of 7.2 µg/kg methylene blue did not produce any change in AMC at low frequencies of nerve stimulation (0.2 Hz, but antagonized the NO-induced Wedensky inhibition. The experimental data suggest that NO-induced Wedensky inhibition may be mediated by the guanylate cyclase-cGMP pathway

Single neuron computation

CERN Document Server

McKenna, Thomas M; Zornetzer, Steven F

1992-01-01

This book contains twenty-two original contributions that provide a comprehensive overview of computational approaches to understanding a single neuron structure. The focus on cellular-level processes is twofold. From a computational neuroscience perspective, a thorough understanding of the information processing performed by single neurons leads to an understanding of circuit- and systems-level activity. From the standpoint of artificial neural networks (ANNs), a single real neuron is as complex an operational unit as an entire ANN, and formalizing the complex computations performed by real n

Adsorption and photodegradation of methylene blue on TiO_2-halloysite adsorbents

International Nuclear Information System (INIS)

Du, Yuanyuan; Zheng, Pengwu

2014-01-01

TiO_2-halloysite (TiO_2-HNT) composites were fabricated by depositing anatase TiO_2 on the halloysite (HNT) surfaces with calcination treatment at 100, 200, 300 and 500 .deg. C. The obtained composites were characterized by transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR) and X-Ray diffraction (XRD). HNT was attached with TiO_2 particles or clusters in sizes of 10-30 nm. With the increasing of calcination temperature, the crystalline of anatase became more perfect, but the structure of HNT could be destroyed at 500 .deg. C. The adsorption and photodegradation of methylene blue (MB) by TiO_2-HNTs were investigated. The kinetic adsorption fit the pseudo second-order, and the isotherm data followed the Langmuir model. The maximum adsorption capacities of MB were in the range of 38.57 to 54.29 mg/g. TiO_2-HNTs exhibited an efficient photocatalytic activity in the decomposition of MB. For TiO_2-HNT calcined at 300 .deg. C, 81.6% MB were degraded after 4 h treatment of UV irradiation

Decolorization of Methylene Blue by Persulfate Activated with FeO Magnetic Particles.

Science.gov (United States)

Hung, Chang-Mao; Chen, Chiu-Wen; Liu, Yi-Yuan; Dong, Cheng-Di

2016-08-01

In this study, the degradation of methylene blue (MB) was conducted to evaluate the feasibility of using persulfate oxidation activated with iron oxide (FeO) magnetic particles. The results demonstrated that the decolorization rate of MB increased with increasing FeO concentration, exhibiting maximum efficiency at pH0 3.0. The kinetics of MB was studied in the binary FeO catalyst and persulfate oxidation system. The surface properties of FeO before and after reaction was analyzed using cyclic voltammogram (CV), three-dimensional excitation-emission fluorescence matrix (EEFM) spectroscopy, zeta potential, particle size distribution measurements, X-ray diffraction (XRD) and environmental scanning electron microscopy-energy dispersive X-ray spectrometry (ESEM-EDS). The CV data indicated that a reversible redox reaction holds the key to explaining the significant activity of the catalyst. EEFM was used to evaluate the catalyst yield of FeO by fluorescence intensity plots with excitation/emission at 220/300 nm and 260/300 nm. The XRD and ESEM-EDS results confirmed the presence of FeO in the catalyst.

Determining stocks and flows of structural wood products in single family homes in the United States between 1950 and 2010

DEFF Research Database (Denmark)

Sianchuk, Robert A.; McFarlane, Paul N.; Ackom, Emmanuel

2012-01-01

The stocks and flows of six major structural wood products (SWPs)-lumber, plywood, oriented strand board [OSB], glue laminated timber, I-joists, and laminated veneer lumber (LVL)-in US single family homes were modeled from 1950 to 2010. The consumption of these products in US single family homes...... and their emissions as construction and demolition wastes were estimated. The net consumption of SWPs decreased from 119 kg/m2 constructed in 1986 to 82 kg/m2 in 2010. Softwood lumber was consistently the predominant SWP, but its usage intensity decreased from 95 kg/m2 in 1986 to 52 kg/ m2 in 2010. Since the 1980s......, modern SWPs, such as I-joists, LVL, and OSB, have replaced lumber and plywood products. The needs of the US single family housing industry have been met by a smaller mass of SWPs per unit area constructed. The mass of SWP present in construction wastes was influenced strongly by building cycles...

Hydrothermal synthesis of graphene oxide/multiwalled carbon nanotube/Fe3O4 ternary nanocomposite for removal of Cu (II) and methylene blue

Science.gov (United States)

Long, Zhihang; Zhan, Yingqing; Li, Fei; Wan, Xinyi; He, Yi; Hou, Chunyan; Hu, Hai

2017-09-01

In this work, highly activated graphene oxide/multiwalled carbon nanotube/Fe3O4 ternary nanocomposite adsorbent was prepared from a simple hydrothermal route by using ferrous sulfate as precursor. For this purpose, the graphene oxide/multiwalled carbon nanotube architectures were formed through the π-π attractions between them, followed by attaching Fe3O4 nanoparticles onto their surface. The structure and composition of as-prepared ternary nanocomposite were characterized by XRD, FTIR, XPS, SEM, TEM, Raman, TGA, and BET. It was found that the resultant porous graphene oxide/multiwalled carbon nanotube/Fe3O4 ternary nanocomposite with large surface area could effectively prevent the π-π stacking interactions between graphene oxide nanosheets and greatly improve sorption sites on the surfaces. Thus, owing to the unique ternary nanocomposite architecture and synergistic effect among various components, as-prepared ternary nanocomposite exhibited high separation efficiency when they were used to remove the Cu (II) and methylene blue from aqueous solutions. Furthermore, the adsorption isotherms of ternary nanocomposite structures for Cu (II) and methylene blue removal fitted the Langmuir isotherm model. This work demonstrated that the graphene oxide/multiwalled carbon nanotube/Fe3O4 ternary nanocomposite was promising as an efficient adsorbent for heavy metal ions and organic dye removal from wastewater in low concentration.

Photocatalytic decolorization of methylene blue over Zn1-xCoxO under visible light irradiation

International Nuclear Information System (INIS)

Xiao Qi; Zhang Jiang; Xiao Chong; Tan Xiaoke

2007-01-01

Co-doped ZnO photocatalysts were prepared by hydrothermal method. The obtained Co-doped ZnO powders were characterized by X-ray diffraction, UV-vis diffuse reflectance spectroscopy and photoluminescence (PL) spectra. The prepared Co-doped ZnO photocatalysts showed high photocatalytic activities for methylene blue decolorization at pH 10.5 under visible light irradiation. It was found that there were certain relationships between PL spectra and photocatalytic activity, namely, the stronger the PL intensity, the larger the content of oxygen vacancies and defects, the higher the photocatalytic activity. Therefore, in this study 3.0 mol% was the most suitable content of Co 2+ in ZnO, at which the recombination of photoinduced electrons and holes could be effectively inhibited and thereby the highest photocatalytic activity was formed

MoS{sub 2}–GO nanocomposites synthesized via a hydrothermal hydrogel method for solar light photocatalytic degradation of methylene blue

Energy Technology Data Exchange (ETDEWEB)

Ding, Yong; Zhou, Yifeng, E-mail: yifengzhou@126.com; Nie, Wangyan; Chen, Pengpeng, E-mail: chenpp@ahu.edu.cn

2015-12-01

Graphical abstract: - Highlights: • The molybdenum disulfide–graphene oxide (MoS{sub 2}–GO) nanocomposite was synthesized via a one-step hydrothermal hydrogel method. • MoS{sub 2} and GO were composited fairly well in the obtained nanocomposites. • The electrons–hole pair recombination rate of MoS{sub 2} was greatly reduced via compositing with graphene. • The MoS{sub 2}–GO nanocomposite exhibited excellent photocatalytic performance for the degradation of methylene blue under solar light irradiation. - Abstract: In this work, molybdenum disulfide–graphene oxide (MoS{sub 2}–GO) composite hydrogel was prepared via a one-step hydrothermal method. The morphology and structure of the as-prepared hydrogels with different proportions of MoS{sub 2} and GO were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, electrochemical impedance spectra and UV–vis absorption spectroscopy. The photocatalytic performance of MoS{sub 2}–GO nanocomposites was studied toward the degradation of methylene blue (MB). Results showed that the MoS{sub 2}–GO nanocomposites exhibited improved photocatalytic activities in the degradation of MB with a maximum degradation rate of 99% under solar lights irradiation within 60 min. The synthesized MoS{sub 2}–GO composite hydrogel possesses great potential toward the development of newly synthesizable catalysts in the field of organic degradation in water.

Synthesis and characterization of aromatic self-assembled monolayers containing methylene and ethyleneglycol entities by means of sum-frequency generation spectroscopy

International Nuclear Information System (INIS)

Dreesen, L.; Sartenaer, Y.; Peremans, A.; Thiry, P.A.; Humbert, C.; Grugier, J.; Marchand-Brynaert, J.

2006-01-01

We use infrared-visible sum-frequency generation (SFG) spectroscopy in order to investigate the adsorption properties on Pt(111) of molecules having CH 3 -C 6 H 4 -(O-CH 2 -CH 2 ) n -O-(CH 2 ) m -SH as general chemical formula. We synthesized three molecules defined by the values m = 5 n = 4, m = 11 n = 4, m = 11 n = 8 and characterized them by Nuclear Magnetic Resonance spectroscopy. Thanks to spectroscopic measurements, we show that these molecules build self-assembled monolayers on Pt(111). First, the weak SFG signals arising from the ad-layer indicate low order and surface coverage of the substrate by these molecules. Next, the vibrational fingerprints of the aforementioned molecules are determined between 2825 and 3125 cm - 1 and the observed SFG spectral features are ascribed on the basis of the analysis of shorter and simpler molecules (1-dodecanethiol, 4-methylbenzenethiol and CH 3 -C 6 H 4 -O-(CH 2 ) 11 -SH) also adsorbed on Pt(111). The occurrence of methylene vibration modes indicates a significant amount of chain defects whatever the n and m numbers are. Finally, the identification of a particular vibration mode, characteristic of the aromatic ring, enables us to qualitatively discuss the effect of the number of methylene and ethylene glycol entities on its orientation. More precisely, higher these numbers, more tilted (with respect to the substrate normal) the aromatic ring plane is

Age-related changes in the global skeletal uptake of technetium-99m methylene diphosphonate in healthy women

International Nuclear Information System (INIS)

Carnevale, V.; Frusciante, V.; Scillitani, A.; Modoni, S.; Pileri, M.; Chiodini, I.; Dicembrino, F.; Romagnoli, E.; Minisola, S.

1996-01-01

A short-term evaluation of global skeletal uptake (GSU) of technetium-99m methylene diphosphonate (MDP) was performed in 40 healthy female subjects with a wide age range in order to investigate the clinical performance of the technique and to detect the age-related changes in bone turnover. The results obtained were compared with measurements of the main biochemical markers of skeletal metabolism. We found that GSU increases progressively with age, independently of concomitant changes in renal function; significant correlations with biochemical markers of bone formation were also found. Therefore, the method appears to provide useful information concerning the bone turnover rate, and is also applicable to elderly people owing to its simplicity. (orig.). With 4 figs., 2 tabs

Brain hypoperfusion on Tc-99m-ethylene dicysteine diethyl ester single-photon emission computed tomography in Hashimoto's encephalopathy

OpenAIRE

Grande, Mar?a Luz Dom?nguez; Constantino, Ana; Rayo, Juan Ignacio; Serrano, Justo; Infante, Jose Rafael; Garcia, Lucia; Duran, Carmen

2013-01-01

We present a 17-year-old female, previously diagnosed of autoimmune hyperthyroidism who had an acute neurological episode and presented high antithyroid antibodies titers, cerebral spinal fluid and electroencephalogram changes. Tc-99m ethylene dicysteine diethyl ester brain single-photon emission computed tomography (SPECT) showed global and patchy hypoperfusion. With glucocorticoid therapy, clinical symptoms disappeared; there was a decrease in antithyroid antibody levels and repeat brain SP...

Reactions of 3-Formylchromone with Active Methylene and Methyl Compounds and Some Subsequent Reactions of the Resulting Condensation Products

Directory of Open Access Journals (Sweden)

M. Lácova

2005-08-01

Full Text Available This review presents a survey of the condensations of 3-formylchromone with various active methylene and methyl compounds, e.g. malonic or barbituric acid derivatives, five-membered heterocycles, etc. The utilisation of the condensation products for the synthesis of different heterocyclic systems, which is based on the ability of the γ-pyrone ring to be opened by the nucleophilic attack is also reviewed. Finally, the applications of microwave irradiation as an unconventional method of reaction activation in the synthesis of condensation products is described and the biological activity of some chromone derivatives is noted.

Stimulus-response functions of single avian olfactory bulb neurones.

Science.gov (United States)

McKeegan, Dorothy E F; Demmers, Theodorus G M; Wathes, Christopher M; Jones, R Bryan; Gentle, Michael J

2002-10-25

This study investigated olfactory processing in a functional context by examining the responses of single avian olfactory bulb neurones to two biologically important gases over relevant concentration ranges. Recordings of extracellular spike activity were made from 80 single units in the left olfactory bulb of 11 anaesthetised, freely breathing adult hens (Gallus domesticus). The units were spontaneously active, exhibiting widely variable firing rates (0.07-47.28 spikes/s) and variable temporal firing patterns. Single units were tested for their response to an ascending concentration series of either ammonia (2.5-100 ppm) or hydrogen sulphide (1-50 ppm), delivered directly to the olfactory epithelium. Stimulation with a calibrated gas delivery system resulted in modification of spontaneous activity causing either inhibition (47% of units) or excitation (53%) of firing. For ammonia, 20 of the 35 units tested exhibited a response, while for hydrogen sulphide, 25 of the 45 units tested were responsive. Approximate response thresholds for ammonia (median threshold 3.75 ppm (range 2.5-60 ppm, n=20)) and hydrogen sulphide (median threshold 1 ppm (range 1-10 ppm, n=25)) were determined with most units exhibiting thresholds near the lower end of these ranges. Stimulus response curves were constructed for 23 units; 16 (the most complete) were subjected to a linear regression analysis to determine whether they were best fitted by a linear, log or power function. No single function provided the best fit for all the curves (seven were linear, eight were log, one was power). These findings show that avian units respond to changes in stimulus concentration in a manner generally consistent with reported responses in mammalian olfactory bulb neurones. However, this study illustrates a level of fine-tuning to small step changes in concentration (<5 ppm) not previously demonstrated in vertebrate single olfactory bulb neurones.

A novel bio-degradable polymer stabilized Ag/TiO2 nanocomposites and their catalytic activity on reduction of methylene blue under natural sun light.

Science.gov (United States)

Geetha, D; Kavitha, S; Ramesh, P S

2015-11-01

In the present work we defined a novel method of TiO2 doped silver nanocomposite synthesis and stabilization using bio-degradable polymers viz., chitosan (Cts) and polyethylene glycol (PEG). These polymers are used as reducing agents. The instant formation of AgNPs was analyzed by visual observation and UV-visible spectrophotometer. TiO2 nanoparticles doped at different concentrations viz., 0.03, 0.06 and 0.09mM on PEG/Cts stabilized silver (0.04wt%) were successfully synthesized. This study presents a simple route for the in situ synthesis of both metal and polymer confined within the nanomaterial, producing ternary hybrid inorganic-organic nanomaterials. The results reveal that they have higher photocatalytic efficiencies under natural sun light. The synthesized TiO2 doped Ag nanocomposites (NCs) were characterized by SEM/EDS, TEM, XRD, FTIR and DLS with zeta potential. The stability of Ag/TiO2 nanocomposite is due to the high negative values of zeta potential and capping of constituents present in the biodegradable polymer which is evident from zeta potential and FT-IR studies. The XRD and EDS pattern of synthesized Ag/TiO2 NCs showed their crystalline structure, with face centered cubic geometry oriented in (111) plane. AFM and DLS studies revealed that the diameter of stable Ag/TiO2 NCs was approximately 35nm. Moreover the catalytic activity of synthesize Ag/TiO2 NCs in the reduction of methylene blue was studied by UV-visible spectrophotometer. The synthesized Ag/TiO2 NCs are observed to have a good catalytic activity on the reduction of methylene blue by bio-degradable which is confirmed by the decrease in absorbance maximum value of methylene blue with respect to time using UV-vis spectrophotometer. The significant enhancement in the photocatalytic activity of Ag/TiO2 nanocomposites under sun light irradiation can be ascribed to the effect of noble metal Ag by acting as electron traps in TiO2 band gap. Copyright © 2015. Published by Elsevier Inc.

Allocating multiple units

DEFF Research Database (Denmark)

Tranæs, Torben; Krishna, Kala

2002-01-01

This paper studies the allocation and rent distribution in multi-unit, combinatorial-bid auctions under complete information. We focus on the natural multi-unit analogue of the first-price auction, where buyers bid total payments, pay their bids, and where the seller allocates goods to maximize his...... auction, which is the multi unit analogue of a second-price auction. Furthermore, we characterize these equilibria when valuations take a number of different forms: diminishing marginal valuations, increasing average valuations, and marginal valuations with single turning points...

Adsorption behaviour of methylene blue onto Jordanian diatomite: a kinetic study.

Science.gov (United States)

Al-Ghouti, Mohammad A; Khraisheh, Majeda A M; Ahmad, Mohammad N M; Allen, Stephen

2009-06-15

The effect of initial concentration, particle size, mass of the adsorbent, pH and agitation speed on adsorption behaviour of methylene blue (MB) onto Jordanian diatomite has been investigated. The maximum adsorption capacity, q, increased from 75 to 105 mg/g when pH of the dye solution increased from 4 to 11. It is clear that the ionisable charge sites on the diatomite surface increased when pH increased from 4 to 11. When the solution pH was above the pH(ZPC), the diatomite surface had a negative charge, while at low pH (pHdiatomite did not follow the pseudo-first order model and had low correlation coefficients (R(2)diatomite when the particle size distribution is less than 250-500 microm. While at larger particle size 250-500 microm, the maximum uptake capacity was dependent on the particle size. It would imply that the MB adsorption is limited by the external surface and that intraparticle diffusion is reduced. The effect of the agitation speeds on the removal of MB from aqueous solution using the diatomite is quite low. The MB removal increased from 43 to 100% when mass of the diatomite increased from 0.3 to 1.7 g.

The effectiveness of environmental strategies on noise reduction in a pediatric intensive care unit: creation of single-patient bedrooms and reducing noise sources.

Science.gov (United States)

Kol, Emine; Aydın, Perihan; Dursun, Oguz

2015-07-01

Noise is a substantial problem for both patients and healthcare workers in hospitals. This study aimed to determine the effectiveness of environmental strategies (creating single-patient rooms and reducing noise sources) in noise reduction in a pediatric intensive care unit. Noise measurement in the unit was conducted in two phases. In the first phase, measurements aimed at determining the unit's present level of noise were performed over 4 weeks in December 2013. During the month following the first measurement phase, the intensive care unit (ICU) was moved to a new location and noise-reducing strategies were implemented. The second phase, in May 2014, measured noise levels in the newly constructed environment. The noise levels before and after environmental changes were statistically significant at 72.6 dB-A and 56 dB-A, respectively (p noise-reducing strategies can be effective in controlling environmental noise in the ICU. © 2015, Wiley Periodicals, Inc.

MULTILAYER POROUS COMPOSITE FROM WASTE GLASS FOR WATER FILTRATION

Directory of Open Access Journals (Sweden)

M. P. Aji

2015-07-01

Full Text Available Multilayer porous composite have been produced through the heating process at temperature T=700oC for 2.5 h. Single layered porous composite was made with a varied mass percentage of from PEG polymer  1% to 10%. Double-layered porous composite were made by the arrangement of porosity (4:3%, (4:2% and (3:2%, while the three-layers porous composite have an arrangement (4:3:2%. Performance of multilayer porous composite for water filtration with pollutants of methylene blue 100 ppm was estimated from the absorbance spectrum. Rejection of methylene blue pollutants from single layered porous composite increases when the fraction of PEG polymer tend to be smaller in the matrix. Meanwhile, the double layered porous composite has a degradation of methylene blue pollutants are better than one layer. Triple layered porous composite have good performance for the water filtration where all the pollutants of methylene blue be able to be filtered.   Komposit pori berlapis telah dihasilkan dengan proses pemanasan pada temperatur T=700oC selama 2.5 jam. Komposit pori satu lapis dibuat dengan variasi persen massa polimer PEG 1% hingga 10%. Komposit pori dua lapis dibuat dengan susunan porositas (4:3%, (4:2% dan (3:2%, sedangkan komposit pori tiga lapis memiliki susunan porositas (4:3:2%. Kinerja komposit pori berlapis untuk filter air dengan polutan methylene blue 100 ppm diestimasi dari spektrum absorbansi. Rejeksi polutan methylene blue dari komposit pori satu lapis meningkat saat fraksi polimer PEG cenderung lebih kecil dalam matrik komposit. Sedangkan, komposit pori dua lapis memiliki kemampuan untuk degradasi polutan methylene blue yang lebih baik dari satu lapis. Komposit pori tiga lapis memiliki kinerja yang baik untuk filter air dimana seluruh polutan methylene blue mampu disaring. 

Adsorption mechanism of microcrystalline cellulose as green adsorbent for the removal of cationic methylene blue dye

International Nuclear Information System (INIS)

Tan, K.B.; Salamatinia, B.

2016-01-01

The adsorption mechanism of pure cellulose is yet to be explored. Thus, in this study, the adsorption mechanism of Microcrystalline Cellulose (MCC), a polysaccharide which is renewable, low cost and non-toxic, was studied on the adsorption of model dye Methylene blue (MB). It was found that the main adsorption mechanism of MB on MCC was due to the electrostatic attraction between the positively charged MB dye and negatively charged MCC. Thus, physical adsorption was the dominant effect, since electrostatic attraction is categorized as physical adsorption. This was verified by Dubinin-Radushkevich isotherm, whereby mean free energy adsorption value was found to be less than 8 kJ/mol. The values of Gibbs free energy for thermodynamics studies were found to be within the range of -20 kJ/mol and 0 kJ/mol, which also indicated physical adsorption. It was due to the electrostatic attraction as adsorption mechanism of this adsorption process which resulted rapid adsorption of MB dye. It was found that equilibrium dye concentration was achieved between 1-3 minutes, depending on the adsorption temperature. The rapid adsorption, as compared to a lot of materials, showed the potential of MCC as the future of green adsorbent. The adsorption of Methylene Blue on MCC fitted well in Langmuir Isotherm, with R2 values of higher than 0.99, while fitted moderately in Freundlich Isotherm, with R2 values between 0.9224 and 0.9223. Comparatively, the adsorption of MB on MCC fitted best Langmuir Isotherm as compared to Freundlich Isotherm which monolayer adsorption occurred at the homogenous surface of MCC. This also indicated adsorbed MB molecules do not interact with each other at neighboring adsorption sites. The maximum adsorption capacity calculated from Langmuir Isotherm was found to be 4.95 mg/g. Despite the potential of MCC as green adsorbent, the challenge of low adsorption capacity has to be addressed in the future. (author)

Brain hypoperfusion on Tc-99m-ethylene dicysteine diethyl ester single-photon emission computed tomography in Hashimoto's encephalopathy

International Nuclear Information System (INIS)

Grande, María Luz Domínguez; Rayo, Juan Ignacio; Serrano, Justo; Infante, Jose Rafael; Garcia, Lucia; Duran, Carmen; Constantino, Ana

2013-01-01

We present a 17-year-old female, previously diagnosed of autoimmune hyperthyroidism who had an acute neurological episode and presented high antithyroid antibodies titers, cerebral spinal fluid and electroencephalogram changes. 99m Tc ethylene dicysteine diethyl ester brain single-photon emission computed tomography (SPECT) showed global and patchy hypoperfusion. With glucocorticoid therapy, clinical symptoms disappeared; there was a decrease in antithyroid antibody levels and repeat brain SPECT revealed improvement of perfusion. (author)

Efficient degradation of Methylene Blue dye over highly reactive Cu doped strontium titanate (SrTiO3) nanoparticles photocatalyst under visible light.

Science.gov (United States)

Rahman, Qazi Inamur; Ahmad, Musheer; Misra, Sunil Kumar; Lohani, Minaxi

2012-09-01

Visible light induced photocatalysts of Cu doped SrTiO3 (Cu/SrTiO3) nanoparticles with the size -60-75 nm were prepared via facile sol-gel method. The morphological, optical, crystalline properties and compositions of synthesized Cu/SrTiO3 nanoparticles were thoroughly characterized by field emission scanning electron microscopy (FE-SEM), powder X-ray diffraction (XRD), ultra violet-visible spectroscopy (UV-Vis) and energy dispersive X-ray (EDX). A significant red shift in the UV-diffused reflectance spectrum was observed and the absorption edge shifted to visible region by the Cu doping. Surprisingly, the band gap of SrTiO3 was changed from 3.2 eV drop to 2.96 eV. The photocatalytic activity of the synthesized Cu/SrTiO3 nanoparticles was demonstrated for the degradation of Methylene Blue dye under visible light irradiation. The formation of new acceptor region in Cu/SrTiO3 was responsible for high photocatalytic activity of Cu/SrTiO3 nanoparticles. The results showed that the Methylene Blue dye was degraded by -66% within time span of 2 h over the Cu/SrTiO3 nanoparticles. This dye degradation reaction followed the Langmuir-Hinshelwood kinetics and also exhibited first order reaction rate. The calculated rate constant for the degradation reaction following first order kinetics was k = 0.0016 min(-1).

Scavenging behaviour of meranti sawdust in the removal of methylene blue from aqueous solution

International Nuclear Information System (INIS)

Ahmad, A.; Rafatullah, M.; Sulaiman, O.; Ibrahim, M.H.; Hashim, R.

2009-01-01

Meranti (Philippine mahogany) sawdust, an inexpensive material, showed strong scavenging behaviour through adsorption for the removal of methylene blue (MB) from aqueous solution. Batch studies were performed to evaluate and optimize the effects of various parameters such as contact time, pH, initial dye concentrations and adsorbent dosage. Langmuir, Freundlich and Temkin isotherms were used to analyze the equilibrium data at different temperatures. The experimental data fitted well with the Langmuir adsorption isotherm, indicating thereby the mono layer adsorption of the dye. The monolayer sorption capacity of meranti sawdust for MB was found to be 120.48, 117.64, 149.25 and 158.73 mg/g at 30, 40, 50 and 60 deg. C, respectively. Thermodynamic calculations showed that the MB adsorption process is endothermic and spontaneous in nature. Kinetic studies showed that the adsorption followed a pseudo-second-order kinetic model. The results indicated that the meranti sawdust could be an alternative material in place of more costly adsorbents used for dye removal.

Perceptions of safety culture vary across the intensive care units of a single institution.

Science.gov (United States)

Huang, David T; Clermont, Gilles; Sexton, J Bryan; Karlo, Crystal A; Miller, Rachel G; Weissfeld, Lisa A; Rowan, Kathy M; Angus, Derek C

2007-01-01

To determine whether safety culture factors varied across the intensive care units (ICUs) of a single hospital, between nurses and physicians, and to explore ICU nursing directors' perceptions of their personnel's attitudes. Cross-sectional surveys using the Safety Attitudes Questionnaire-ICU version, a validated, aviation industry-based safety culture survey instrument. It assesses culture across six factors: teamwork climate, perceptions of management, safety climate, stress recognition, job satisfaction, and work environment. Four ICUs in one tertiary care hospital. All ICU personnel. We conducted the survey from January 1 to April 1, 2003, and achieved a 70.2% response rate (318 of 453). We calculated safety culture factor mean and percent-positive scores (percentage of respondents with a mean score of > or =75 on a 0-100 scale for which 100 is best) for each ICU. We compared mean ICU scores by ANOVA and percent-positive scores by chi-square. Mean and percent-positive scores by job category were modeled using a generalized estimating equations approach and compared using Wald statistics. We asked ICU nursing directors to estimate their personnel's mean scores and generated ratios of their estimates to the actual scores.Overall, factor scores were low to moderate across all factors (range across ICUs: 43.4-74.9 mean scores, 8.6-69.4 percent positive). Mean and percent-positive scores differed significantly (p safety culture variation exists across ICUs of a single hospital. ICU nursing directors tend to overestimate their personnel's attitudes, particularly for teamwork. Culture assessments based on institutional level analysis or director opinion may be flawed.

Photodynamic antibacterial enhanced effect of methylene blue-gold nanoparticles conjugate on Staphylococcal aureus isolated from impetigo lesions in vitro study.

Science.gov (United States)

Tawfik, Abeer Attia; Alsharnoubi, Jehan; Morsy, Mona

2015-06-01

Staphylococcal aureus is the most common organism which has been encountered in impetigo infection. Gold nanoparticles can be used as a tool to deliver antimicrobials or to enhance photodynamic destruction of bacteria. To evaluate the photodynamic effect of methylene blue gold nanoparticles (MB-gold nanoparticles conjugate) on S. aureus which were isolated from impetigo lesions. Twenty children were diagnosed clinically as impetigo, and aged from 3 to 5 years of both sexes were recruited in the study. Two bacteriological samples were collected from each patient, identified and cultured. Samples of S. aureus of a concentration of 10(-1)ml were divided into four groups. S. aureus was treated by MB-gold nanoparticles conjugate, gold nanoparticles, MB, and the fourth group served as a control group. Diode laser (660 nm) was used for photoactivation. The bacterial growth inhibition was determined by two methods: the percentage of reduction of viable bacteria count and the optical density (O.D) of bacterial growth. The highest significant inhibitory effect on S. aureus was obtained with MB-gold nanoparticles conjugate when irradiated by diode laser 660 nm (P < 0.0001). The percentage of viable bacteria was 3%. The photoactivated gold nanoparticles showed a significant inhibitory effect on bacterial growth (P < 0.05). A non-significant inhibitory effect was elicited in other groups. The photoactivated MB-gold nanoparticles conjugate showed the maximum inhibitory effect on S. aureus activity. The gold nanoparticles proved efficacy as a drug delivery system. It enhanced the photodynamic antibacterial effect of methylene blue. Copyright © 2015 Elsevier B.V. All rights reserved.

Methyleneation of peptides by N,N,N,N-tetramethylethylenediamine (TEMED) under conditions used for free radical polymerization: a mechanistic study.

Science.gov (United States)

Shirangi, Mehrnoosh; Sastre Toraño, Javier; Sellergren, Börje; Hennink, Wim E; Somsen, Govert W; van Nostrum, Cornelus F

2015-01-21

Free radical polymerization is often used to prepare protein and peptide-loaded hydrogels for the design of controlled release systems and molecular imprinting materials. Peroxodisulfates (ammonium peroxodisulfates (APS) or potassium peroxodisulfates (KPS)) with N,N,N,N-tetramethylethylenediamine (TEMED) are frequently used as initiator and catalyst. However, exposure to these free radical polymerization reagents may lead to modification of the protein and peptide. In this work, we show the modification of lysine residues by ammonium peroxodisulfate (APS)/TEMED of the immunostimulant thymopentin (TP5). Parallel studies on a decapeptide and a library of 15 dipeptides were performed to reveal the mechanism of modification. LC-MS of APS/TEMED-exposed TP5 revealed a major reaction product with an increased mass (+12 Da) with respect to TP5. LC-MS(2) and LC-MS(3) were performed to obtain structural information on the modified peptide and localize the actual modification site. Interpretation of the obtained data demonstrates the formation of a methylene bridge between the lysine and arginine residue in the presence of TEMED, while replacing TEMED with a sodium bisulfite catalyst did not show this modification. Studies with the other peptides showed that the TEMED radical can induce methyleneation on peptides when lysine is next to arginine, proline, cysteine, aspargine, glutamine, histidine, tyrosine, tryptophan, and aspartic acid residues. Stability of peptides and protein needs to be considered when using APS/TEMED in in situ polymerization systems. The use of an alternative catalyst such as sodium bisulfite may preserve the chemical integrity of peptides during in situ polymerization.

Photodynamic action of methylene blue in osteosarcoma cells in vitro.

Science.gov (United States)

Guan, Jiemin; Lai, Xiaoping; Wang, Xinna; Leung, Albert Wingnang; Zhang, Hongwei; Xu, Chuanshan

2014-03-01

Osteosarcoma is a common malignant bone tumor which threatens the life of young people worldwide. To explore alternative strategy for combating osteosarcoma, a light-emitting diode (LED) that activates methylene blue (MB) was used in the present study to investigate cell death of osteosarcoma-derived UMR106 cells. Photocytotoxicity in UMR106 cells was investigated 24h after photodynamic activation of MB using sulforhodamine B (SRB) assay and light microscopy. Apoptosis induction was observed 24h after photodynamic treatment using a confocal laser scanning microscopy (CLSM) with Hoechst 33342 staining. The change in mitochondrial membrane potential (MMP) was analyzed using a flow cytometry with rhodamine 123 staining. MB under red light irradiation caused a drug-concentration (0-100μM) and light-dose (0-32J/cm(2)) dependent cytotoxicity in UMR106 cells. The SRB assay and light microscopy observed a significant decrease in the number of UMR106 cells attached to the bottom of culture well after LED light-activated MB (100μM, 32J/cm(2)). Nuclear shrinkage, chromatin condensation and fragmentation were found in the treated cells by nuclear staining. In addition, flow cytometry showed that the MMP in UMR106 cells was rapidly reduced by photo-activated MB (100μM, 32J/cm(2)). Photodynamic action of MB under LED irradiation could remarkably kill osteosarcoma cells and induce cell apoptosis as well as MMP collapse. Crown Copyright © 2013. Published by Elsevier B.V. All rights reserved.

Structure of single-chain single crystals of isotactic polystyrene and their radiation resistance

International Nuclear Information System (INIS)

Bu Haishan; Cao Jie; Xu Shengyong; Zhang Ze

1997-01-01

The structure of the single-chain single crystals of isotactic polystyrene (i-PS) was investigated by electron diffraction (ED) and high resolution electron microscopy (HREM). The nano-scale single-chain single crystals were found to be very stable to electron irradiation. According to the unit cell of i-PS crystals, the reflection rings in ED pattern and the lattice fringes in HREM images could be indexed, but the lower-index diffractions were not found. It is proposed that the single-chain single crystals are very small, thus secondary electrons may be allowed to escape and radiation damage is highly reduced, and that there are less lower-index lattice planes in the single-chain single crystals to provide sufficient diffraction intensity for recording. HREM images can be achieved at room temperature in the case of single-chain single crystals because of its stability to electron irradiation, therefore, this might be a novel experimental approach to the study of crystal structure of macromolecules

Single-borehole techniques

International Nuclear Information System (INIS)

Klotz, D.; Moser, H.; Trimborn, P.

1978-01-01

Proceeding on the theoretical considerations and on the experience and practice derived from laboratory and field testing, a system consisting of tracer injection units, detector units, measuring probe units and packers is presented, from which the different borehole probes required can be combined. A couple of examples of recent applications shows the position of the Single-Borehole Techniques with respect to the traditional methods used for the measurement of the ground-water flow. A confrontation of the permeabilities of different aquifers consents, both on the basis of the Single-Borehole Techniques as by pumping experiments, the determination of the reliability of the Point-Dilution-Method. The Point-Dilution-Method is giving information about the vertical and horizontal distribution of the permeabilities in an aquifer. By measuring the vertical current in two karst wells, the tributary horizons of a well have been determined, which gave valuable information for the subsequent well construction. Local leakages could be detected by measuring the vertical flow rate through observation wells arranged along a grout curtain erected on both sides of the retaining barrage of the Keban dam. (orig.) [de

Graphene-SnO2 composites for highly efficient photocatalytic degradation of methylene blue under sunlight.

Science.gov (United States)

Seema, Humaira; Christian Kemp, K; Chandra, Vimlesh; Kim, Kwang S

2012-09-07

Graphene sheets decorated with SnO(2) nanoparticles (RGO-SnO(2)) were prepared via a redox reaction between graphene oxide (GO) and SnCl(2). Graphene oxide (GO) was reduced to graphene (RGO) and Sn(2+) was oxidized to SnO(2) during the redox reaction, leading to a homogeneous distribution of SnO(2) nanoparticles on RGO sheets. The scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images show uniform distribution of the nanoparticles on the RGO surface and high-resolution transmission electron microscopy (HRTEM) shows an average particle size of 3-5 nm. The RGO-SnO(2) composite showed an enhanced photocatalytic degradation activity for the organic dye methylene blue under sunlight compared to bare SnO(2) nanoparticles. This result leads us to believe that the RGO-SnO(2) composite could be used in catalytic photodegradation of other organic dyes.

Optimization of methylene blue removal by stable emulsified liquid membrane using Plackett-Burman and Box-Behnken designs of experiments.

Science.gov (United States)

Djenouhat, Meriem; Bendebane, Farida; Bahloul, Lynda; Samar, Mohamed E H; Ismail, Fadhel

2018-02-01

The stability of an emulsified liquid membrane composed of Span80 as a surfactant, D2EHPA as an extractant and sulfuric acid as an internal phase was first studied according to different diluents and many operating parameters using the Plackett-Burman design of experiments. Then the removal of methylene blue from an aqueous solution has been carried out using this emulsified liquid membrane at its stability conditions. The effects of operating parameters were analysed from the Box-Behnken design of experiments. The optimization of the extraction has been realized applying the response surface methodology and the results showed that the dye extraction yielding 98.72% was achieved at optimized conditions.

12 CFR 541.10 - Dwelling unit.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Dwelling unit. 541.10 Section 541.10 Banks and... FEDERAL SAVINGS ASSOCIATIONS § 541.10 Dwelling unit. The term dwelling unit means the unified combination of rooms designed for residential use by one family, other than a single-family dwelling. ...

Methylene blue for clinical anaphylaxis treatment: a case report

Directory of Open Access Journals (Sweden)

Janine Moreira Rodrigues

Full Text Available CONTEXT AND OBJECTIVE: Nitric oxide has a pathophysiological role in modulating systemic changes associated with anaphylaxis. Nitric oxide synthase inhibitors may exacerbate bronchospasm in anaphylaxis and worsen clinical conditions, with limited roles in anaphylactic shock treatment. The aim here was to report an anaphylaxis case (not anaphylactic shock, reversed by methylene blue (MB, a guanylyl cyclase inhibitor. CASE REPORT: A 23-year-old female suddenly presented urticaria and pruritus, initially on her face and arms, then over her whole body. Oral antihistamine was administered initially, but without improvement in symptoms and signs until intravenous methylprednisolone 500 mg. Recurrence occurred after two hours, plus vomiting. Associated upper respiratory distress, pulmonary sibilance, laryngeal stridor and facial angioedema (including erythema and lip edema marked the evolution. At sites with severe pruritus, petechial lesions were observed. The clinical situation worsened, with dyspnea, tachypnea, peroral cyanosis, laryngeal edema with severe expiratory dyspnea and deepening unconsciousness. Conventional treatment was ineffective. Intubation and ventilatory support were then considered, because of severe hypoventilation. But, before doing that, based on our previous experience, 1.5 mg/kg (120 mg bolus of 4% MB was infused, followed by one hour of continuous infusion of another 120 mg diluted in dextrose 5% in water. Following the initial intravenous MB dose, the clinical situation reversed completely in less than 20 minutes, thereby avoiding tracheal intubation. CONCLUSION: Although the nitric oxide hypothesis for MB effectiveness discussed here remains unproven, our intention was to share our accumulated cohort experience, which strongly suggests MB is a lifesaving treatment for anaphylactic shock and/or anaphylaxis and other vasoplegic conditions.

BILATERAL SINGLE SESSION URETEROSCOPY FOR URETERAL ...

African Journals Online (AJOL)

Objectives: To determine the feasibility, safety and success rate of bilateral single session rigid retrograde ureteroscopy (URS) for bilateral ureteral calculi. Patients and Methods: Thirty-five patients underwent bilateral single session ureteroscopic calculus removal. Results: Out of 70 renal units in 35 patients treated, ...

Designing metallic iron based water filters: Light from methylene blue discoloration.

Science.gov (United States)

Btatkeu-K, B D; Tchatchueng, J B; Noubactep, C; Caré, S

2016-01-15

Available water filtration systems containing metallic iron (Fe(0) filters) are pragmatically designed. There is a lack of sound design criteria to exploit the full potential of Fe(0) filters. A science-based design relies on valuable information on processes within a Fe(0) filter, including chemical reactions, hydrodynamics and their relation to the performance of the filter. The aim of this study was to establish a simple method to evaluate the initial performance of Fe(0) filters. The differential adsorptive affinity of methylene blue (MB) onto sand and iron oxide is exploited to characterize the evolution of a Fe(0)/sand system using the pure sand system as operational reference. Five systems were investigated for more than 70 days: pure sand, pure Fe(0), Fe(0)/sand, Fe(0)/pumice and Fe(0)/sand/pumice. Individual systems were characterized by the extent of changes in pH value, iron breakthrough, MB breakthrough and hydraulic conductivity. Results showed that for MB discoloration (i) pure sand was the most efficient system, (ii) hybrid systems were more sustainable than the pure Fe(0) system, and (iii) the pores of used pumice are poorly interconnected. Characterizing the initial reactivity of Fe(0) filters using MB discoloration has introduced a powerful tool for the exploration of various aspects of filter design. Copyright © 2015 Elsevier Ltd. All rights reserved.

Competitive effects of humic acid and wastewater on adsorption of Methylene Blue dye by activated carbon and non-imprinted polymers.

Science.gov (United States)

Murray, Audrey; Örmeci, Banu

2018-04-01

Natural organic matter (NOM), present in natural waters and wastewater, decreases adsorption of micropollutants, increasing treatment costs. This research investigated mechanisms of competition for non-imprinted polymers (NIPs) and activated carbon with humic acid and wastewater. Three different types of activated carbons (Norit PAC 200, Darco KB-M, and Darco S-51) were used for comparison with the NIP. The lower surface area and micropore to mesopore ratio of the NIP led to decreased adsorption capacity in comparison to the activated carbons. In addition, experiments were conducted for single-solute adsorption of Methylene Blue (MB) dye, simultaneous adsorption with humic acid and wastewater, and pre-loading with humic acid and wastewater followed by adsorption of MB dye using NIP and Norit PAC 200. Both the NIP and PAC 200 showed significant decreases of 27% for NIP (p=0.087) and 29% for PAC 200 (p=0.096) during simultaneous exposure to humic acid and MB dye. There was no corresponding decrease for NIP or PAC 200 pre-loaded with humic acid and then exposed to MB. In fact, for PAC 200, the adsorption capacity of the activated carbon increased when it was pre-loaded with humic acid by 39% (p=0.0005). For wastewater, the NIP showed no significant increase or decrease in adsorption capacity during either simultaneous exposure or pre-loading. The adsorption capacity of PAC 200 increased by 40% (p=0.001) for simultaneous exposure to wastewater and MB. Pre-loading with wastewater had no effect on MB adsorption by PAC 200. Copyright © 2017. Published by Elsevier B.V.

Photodynamic inactivation of conidia of the fungus Colletotrichum abscissum on Citrus sinensis plants with methylene blue under solar radiation.

Science.gov (United States)

Gonzales, Júlia C; Brancini, Guilherme T P; Rodrigues, Gabriela B; Silva-Junior, Geraldo José; Bachmann, Luciano; Wainwright, Mark; Braga, Gilberto Ú L

2017-11-01

Antimicrobial photodynamic treatment (APDT) is a promising light based approach to control diseases caused by plant-pathogenic fungi. In the present study, we evaluated the effects of APDT with the phenothiazinium photosensitizer methylene blue (MB) under solar radiation on the germination and viability of conidia of the pathogenic fungus Colletotricum abscissum (former Colletotrichum acutatum sensu lato). Experiments were performed both on petals and leaves of sweet orange (Citrus sinensis) in different seasons and weather conditions. Conidial suspensions were deposited on the leaves and petals surface, treated with the PS (25 or 50μM) and exposed to solar radiation for only 30min. The effects of APDT on conidia were evaluated by counting the colony forming units recovered from leaves and petals and by direct evaluating conidial germination on the surface of these plant organs after the treatment. To better understand the mechanistic of conidial photodynamic inactivation, the effect of APDT on the permeability of the conidial plasma membrane was assessed using the fluorescent probe propidium iodide (PI) together with flow cytometry and fluorescence microscopy. APDT with MB and solar exposure killed C. abscissum conidia and prevented their germination on both leaves and petals of citrus. Reduction of conidial viability was up to three orders of magnitude and a complete photodynamic inactivation was achieved in some of the treatments. APDT damaged the conidial plasma membrane and increased its permeability to PI. No damage to sweet orange flowers or leaves was observed after APDT. The demonstration of the efficacy of APDT on the plant host represents a further step towards the use of the method for control phytopathogens in the field. Copyright © 2017 Elsevier B.V. All rights reserved.

A supramolecular photosensitizer system based on the host-guest complexation between water-soluble pillar[6]arene and methylene blue for durable photodynamic therapy.

Science.gov (United States)

Yang, Kui; Wen, Jia; Chao, Shuang; Liu, Jing; Yang, Ke; Pei, Yuxin; Pei, Zhichao

2018-06-05

A supramolecular photosensitizer system WP6-MB was synthesized based on water-soluble pillar[6]arene and the photosensitizer methylene blue (MB) via host-guest interaction. MB can complex with WP6 directly with a high complex constant without further modification. In particular, WP6-MB can reduce the dark toxicity of MB remarkably. Furthermore, it can efficiently overcome photobleaching and extend the time for singlet oxygen production of MB upon light irradiation, which is significant for durable photodynamic therapy.

Crystal structure of (E)-3-fluoro-N-((5-nitrothiophen-2-yl)methylene)aniline

Energy Technology Data Exchange (ETDEWEB)

Karataş, Şadiye; Tanak, Hasan, E-mail: hasantanak@gmail.com [Amasya University, Department of Physics, Faculty of Arts and Sciences (Turkey); Ağar, Ayşen Alaman [Ondokuz Mayıs University, Department of Chemistry, Faculty of Arts and Sciences (Turkey)

2016-05-15

The structure of the title compound C{sub 11}H{sub 7}FN{sub 2}O{sub 2}S was characterized by single crystal X-ray diffraction. The compound crystallizes in the monoclinic space group P2{sub 1}/n with Z = 12, i.e. with three molecules in asymmetric unit. The molecules are not planar: the dihedral angles between the planes of thiophene and the benzene rings are 42.3(3)°, 42.0(3)°, and 48.9(2)°. In the crystal, intermolecular C–H···F interactions link the molecules through R{sub 2}{sup 2} (14) ring motif. The crystal packing is also stabilized by π···π interactions.

P25-graphene hydrogels: room-temperature synthesis and application for removal of methylene blue from aqueous solution.

Science.gov (United States)

Hou, Chengyi; Zhang, Qinghong; Li, Yaogang; Wang, Hongzhi

2012-02-29

Herein we report a room-temperature synthesis of chemically bonded TiO2 (P25)-graphene composite hydrogels and their use as high performance visible light photocatalysts. The three-dimensional (3D) TiO2-carbon composite exhibits a significant enhancement in the reaction rate in the decontamination of methylene blue, compared to the bare P25. The 3D P25-graphene hydrogel is much easier to prepare and apply as a macroscopic device, compared to the 2D P25-graphene sheets. This work could provide new insights into the room-temperature synthesis of graphene-based materials. As a kind of the novel 3D graphene-based composite, the obtained high performance P25-graphene gel could be widely used in the environmental protection issues. Copyright © 2012. Published by Elsevier B.V.

United States housing, first quarter 2013

Science.gov (United States)

Delton Alderman

2014-01-01

Provides current and historical information on housing market in the United States. Information includes trends for housing permits and starts, housing under construction, and housing completions for single and multifamily units, and sales and construction. This report will be updated regularly.

Methylene blue 1% solution on the prevention of intraperitoneal adhesion formation in a dog model

Directory of Open Access Journals (Sweden)

Marco Augusto Machado Silva

Full Text Available Intraperitoneal adhesions usually are formed after abdominal surgeries and may cause technical difficulties during surgical intervention, chronic abdominal pain and severe obstructions of the gastrointestinal tract. The current study aimed to evaluate the efficacy of methylene blue (MB 1% solution on the prevention of intraperitoneal postsurgical adhesion formation in a canine surgical trauma model. Twenty bitches were submitted to falciform ligament resection, omentectomy, ovariohysterectomy and scarification of a colonic segment. Prior to abdominal closure, 10 bitches received 1mg kg-1 MB intraperitoneally (MB group and 10 bitches received no treatment (control group, CT. On the 15th postoperative day the bitches were submitted to laparoscopy to assess adhesions. The mean adhesion scores were 13.9 (±5.6 for MB group and 20.5 (±6.4 for the CT group (P=0,043. In conclusion, the 1% MB solution was efficient on the prevention of intraperitoneal postoperative adhesion formation in bitches, especially those involving the colonic serosa.

Degradation of methylene blue using pillared TiO2 on de-oiled spent bleaching clay

Science.gov (United States)

Hindryawati, N.; Panggabean, A. S.; Fadillah, N. D.; Erwin; Daniel

2018-04-01

Degradation of methylene blue (MB) using pillared TiO2 onto spent bleaching clay has been conducted. Activation of deoiled spent bleaching clay (DSBC) has been done using acid, followed by pillarization with TiO2 using rarasaponin from Klerak fruit as surfactant. From the X-ray diffraction results show the mineral on DSBC is rectorite with dioctahedral mica layer and dioctahedral smectite with ratio 2:1. This molecule have formula Na.Al4(Si, Al)8.O20.(OH)4. H2O and after calcinations the pattern TiO2 was appearance at 2θ: 27.4460°, 36.0850°, 54.3216° and 56.6403°. In order to test the catalytic performance of Ti-DSBC for photodegradation of MB under UV light was conducted under several reaction conditions. The highest degradation of MB was 90 % within 50 minutes and Ti-DSBC can be reused until 5 cycles with percent degradation MB was 84 %.

Evaluation of workers' exposure to methylene diphenyl diisocyanate (MDI) in an automobile manufacturing company, Iran.

Science.gov (United States)

Kakooei, Hossein; Shahtaheri, Seyed Jamaleddin; Karbasi, Hossein-Ali

2006-01-01

Evaluation of personal inhalation exposure to methylene diphenyl diisocyanate (MDI) among 39 employees, working in the window fixation and window glue processes in an automobile manufacturing company was performed. This study was conducted for both case and control groups. After sampling and sample preparation processes, MDI was determined with a UV-VIS spectrophotometer at 590 nm; the lung function was assessed with a digital spirometer, too. The average concentration of MDI in the window fixation, and window glue workplaces were 34.53 and 27.37 micro g/m3, respectively, which was lower than the threshold limit value (TLV) recommended by the American Conference of Governmental Industrial Hygienists (ACGIH) (51 micro g/m3). Respiratory symptoms in the exposed group were significantly different compared to the unexposed group (p < .05). Lung capacities in the case group were lower than in the control group (p < .05). Therefore, MDI can be easily measured making it possible to evaluate the adverse effects caused by occupational exposure.

Facile decolorization of methylene blue by morphology-dependence δ-MnO2 nanosheets -modified diatomite

Science.gov (United States)

Yu, Ting Ting; Li, Kai Lin; Guo, Xiao Long; Li, Fei; Huang, Jia Mu; Zhang, Yu Xin

2015-12-01

In this work, coscinodiscus-diatomite and melosira-diatomite have been decorated by ultrathin birnessite MnO2 (δ-MnO2) nanosheets through a one-pot hydrothermal method without using any surfactants. The δ-MnO2 nanosheets are observed to grow vertically on the purified melosira-diatomite as well as coscinodiscus-diatomite. Moreover, the two composites exhibit high efficiency for decomposing methylene blue (MB) in the presence of H2O2. The coscinodiscus-diatmite@MnO2 achieves a removal rate of 81.8% (2 h), and yet melosira-diatomite@MnO2 reaches a higher degradation rate of 91.3% in 2 h. Additionally, the effects of catalyst amount, catalysis reaction temperature, preparing time have also been investigated. In principle, the diverse diatomite@MnO2 nanostructures not only present an environmentally friendly and low cost with a good cycling stability, but also offer a simple way for the catalytic degradation of dye waste water in practical applications.

Radiolytic crosslinking and chain scission in aliphatic and alkyl-aromatic polyamides: Pt. 2

International Nuclear Information System (INIS)

Lyons, B.J.; Glover, L.C. Jr.

1991-01-01

Regression analysis of the radiation parameters of nine aliphatic polyamides exposed to ionizing radiation leads to the conclusion that the decline in the ratio of chain scission to crosslinking in higher aliphatic polyamides is best related to the linear increase in the methylene content of, or the number of methylene groups in, the polyamide repeat unit. G(crosslink)[G(X)] and G(chain scission) [G(CS)] values, however, do not correlate well with either of these parameters. Rather it is found that the major determinant of yields [about 80-85% of the variation for G(X), 70% for G(CS)] is the number of hydrogen atoms or methylene groups in the amine residue. Although, logically, the yields of crosslinks and chain scissions in polyamides would be expected to tend to that of polyethylene as the number of methylene groups in the repeat unit increases, use of two models assuming an exponential trend to the G(X) value characteristic of polyethylene in the analysis did not provide better fits to the data than the simple linear model referred to above. Indeed, the assumption of a significant exponential trend factor led to a marked drop in the goodness of fit. (author)

Flexible graphene composites for removal of methylene blue dye-contaminant from water

Science.gov (United States)

Oliva, J.; Martinez, A. I.; Oliva, A. I.; Garcia, C. R.; Martinez-Luevanos, A.; Garcia-Lobato, M.; Ochoa-Valiente, R.; Berlanga, A.

2018-04-01

This work presents the use of flexible graphene composites (FGCs) fabricated by a casting method for the removal of Methylene blue (MB) dye from water. Those FGCs with elastic modulus of 15 MPa had enough mechanical resistance to support the Al2O3:Eu3+ and SrAl2O4:Bi3+ photocatalytic powders. After the incorporation of those powders in the FGCs, their photocatalytic activity was evaluated by monitoring the degradation of MB dye under solar irradiation. Scanning electron microscopy (SEM) images demonstrate that the surface of FGCs with catalysts powders presents pores with sizes in the range of 15-40 μm, which favored the sunlight absorption by scattering effects. Moreover, X-Ray diffraction measurements confirmed the formation of the composites by displacements of their diffraction peaks. The MB dye was completely removed (by photocatalysis and by physical adsorption) from the water after 180 min and 270 min by using the FGCs with Al2O3:Eu3+ and SrAl2O4:Bi3+ catalysts respectively. Hence, the results of photocatalytic activity suggest that our FGCs could be used as an effective support of catalyst powders for the easy removal of dye contaminants in wastewater treatment plants.

Removal of basic dye (methylene blue) from wastewaters utilizing beer brewery waste

International Nuclear Information System (INIS)

Tsai, W.-T.; Hsu, H.-C.; Su, T.-Y.; Lin, K.-Y.; Lin, C.-M.

2008-01-01

In the work, the beer brewery waste has been shown to be a low-cost adsorbent for the removal of basic dye from the aqueous solution as compared to its precursor (i.e., diatomite) based on its physical and chemical characterizations including surface area, pore volume, scanning electron microscopy (SEM), and non-mineral elemental analyses. The pore properties of this waste were significantly larger than those of its raw material, reflecting that the trapped organic matrices contained in the waste probably provided additional adsorption sites and/or adsorption area. The results of preliminary adsorption kinetics showed that the diatomite waste could be directly used as a potential adsorbent for removal of methylene blue on the basis of its adsorption-biosorption mechanisms. The adsorption parameters thus obtained from the pseudo-second-order model were in accordance with their pore properties. From the results of adsorption isotherm at 298 K and the applicability examinations in treating industrial wastewater containing basic dye, it was further found that the adsorption capacities of diatomite waste were superior to those of diatomite, which were also in good agreement with their corresponding physical properties. From the results mentioned above, it is feasible to utilize the food-processing waste for removing dye from the industrial dying wastewater

Removal of basic dye (methylene blue) from wastewaters utilizing beer brewery waste.

Science.gov (United States)

Tsai, Wen-Tien; Hsu, Hsin-Chieh; Su, Ting-Yi; Lin, Keng-Yu; Lin, Chien-Ming

2008-06-15

In the work, the beer brewery waste has been shown to be a low-cost adsorbent for the removal of basic dye from the aqueous solution as compared to its precursor (i.e., diatomite) based on its physical and chemical characterizations including surface area, pore volume, scanning electron microscopy (SEM), and non-mineral elemental analyses. The pore properties of this waste were significantly larger than those of its raw material, reflecting that the trapped organic matrices contained in the waste probably provided additional adsorption sites and/or adsorption area. The results of preliminary adsorption kinetics showed that the diatomite waste could be directly used as a potential adsorbent for removal of methylene blue on the basis of its adsorption-biosorption mechanisms. The adsorption parameters thus obtained from the pseudo-second-order model were in accordance with their pore properties. From the results of adsorption isotherm at 298 K and the applicability examinations in treating industrial wastewater containing basic dye, it was further found that the adsorption capacities of diatomite waste were superior to those of diatomite, which were also in good agreement with their corresponding physical properties. From the results mentioned above, it is feasible to utilize the food-processing waste for removing dye from the industrial dying wastewater.

Removal of basic dye (methylene blue) from wastewaters utilizing beer brewery waste

Energy Technology Data Exchange (ETDEWEB)

Tsai, W.-T. [Graduate Institute of Bioresources, National Pingtung University of Science and Technology, Pingtung 912, Taiwan (China)], E-mail: wttsai@mail.npust.edu.tw; Hsu, H.-C.; Su, T.-Y.; Lin, K.-Y.; Lin, C.-M. [Department of Environmental Engineering and Science, Chia Nan University of Pharmacy and Science, Tainan 717, Taiwan (China)

2008-06-15

In the work, the beer brewery waste has been shown to be a low-cost adsorbent for the removal of basic dye from the aqueous solution as compared to its precursor (i.e., diatomite) based on its physical and chemical characterizations including surface area, pore volume, scanning electron microscopy (SEM), and non-mineral elemental analyses. The pore properties of this waste were significantly larger than those of its raw material, reflecting that the trapped organic matrices contained in the waste probably provided additional adsorption sites and/or adsorption area. The results of preliminary adsorption kinetics showed that the diatomite waste could be directly used as a potential adsorbent for removal of methylene blue on the basis of its adsorption-biosorption mechanisms. The adsorption parameters thus obtained from the pseudo-second-order model were in accordance with their pore properties. From the results of adsorption isotherm at 298 K and the applicability examinations in treating industrial wastewater containing basic dye, it was further found that the adsorption capacities of diatomite waste were superior to those of diatomite, which were also in good agreement with their corresponding physical properties. From the results mentioned above, it is feasible to utilize the food-processing waste for removing dye from the industrial dying wastewater.

Investigation on the uptake and release ability of β-cyclodextrin functionalized Fe_3O_4 magnetic nanoparticles by methylene blue

International Nuclear Information System (INIS)

Zhou, Yehong; Sun, Linlin; Wang, Haixia; Liang, Wenting; Yang, Jun; Wang, Li; Shuang, Shaomin

2016-01-01

β-cyclodextrin functionalized magnetic nanoparticles (β-CD-MNPs) having a core–shell structure were fabricated with a layer-by-layer method by combining 3-aminopropyl triethoxysilane coated magnetic Fe_3O_4 nanoparticles (AP-MNPs) with 6-O-toluenesulfonyl-β-cyclodextrin (6-TsO-β-CD) at 70 °C. The characterization by transmission electron microscopy revealed β-CD-MNPs having an average diameter of 12 ± 2 nm and an average hydrodynamic diameter of 56.8 nm in aqueous solution by dynamic light scattering. The β-CD grafting was confirmed by Fourier-Transformed Infrared spectroscopy, and the amount of β-CD grafted on MNPs was determined as 60 mg/g by thermogravimetric analysis. The uptake and release ability of β-CD-MNPs was investigated using methylene blue (MB) as a biological staining dye by spectrophotometric method. The results showed that the uptake and release were greatly influenced by the pH value of dye solution, with a maximum loading capacity of 78.4 mg/g under pH = 8 at 25 °C, and the release was easily achieved at 73% within the first hour at physiological condition. The adsorption isotherms were examined by Langmuir and Freundlich models, and the satisfactory fitting to the Langmuir model suggested the adsorption on β-CD-MNPs as a mono-layer coverage. - Highlights: • Investigation of uptake and release of methylene blue by β-CD-MNPs. • Superparamagnetic property of β-CD-MNPs nanoparticles. • Targeted delivery with the assistance of external magnetic field. • Nanomaterials with coupled advantages of amphiphilic structure and superparamagnetism.

Preconcentration of Sn (II) using the methylene blue on the activated carbon and its determination by spectrophotometry method.

Science.gov (United States)

Khodadoust, Saeid; Cham Kouri, Narges

2014-04-05

A simple and accurate spectrophotometric method for determination of trace amounts of Sn (II) ion in soil sample was developed by using the methylene blue (MB) in the presence of activated carbon (AC) as the adsorbent Solid Phase Extraction (SPE) of Sn (II) and then determined by UV-Vis. The Beer's law is obeyed over the concentration range of 1-80ngmL(-1) of Sn (II) with the detection limits of 0.34ngmL(-1). The influence of type and volume of eluent, concentration of MB, pH, and amount of AC on sensitivity of spectrophotometric method were optimized. The method has been successfully applied for Sn (II) ion determination in soil sample. Copyright © 2013 Elsevier B.V. All rights reserved.

Diffracted X-ray tracking: new system for single molecular detection with X-rays

CERN Document Server

Sasaki, Y C; Adachi, S; Suzuki, Y; Yagi, N

2001-01-01

We propose a new X-ray methodology for direct observations of the behaviors of single molecular units in real time and real space. This new system, which we call Diffracted X-ray Tracking (DXT), monitors the Brownian motions of a single molecular unit by observations of X-ray diffracted spots from a nanocrystal, tightly bound to the individual single molecular unit in bio-systems. DXT does not determine any translational movements, but only orientational movements.

Diffracted X-ray tracking: new system for single molecular detection with X-rays

International Nuclear Information System (INIS)

Sasaki, Y.C.; Okumura, Y.; Adachi, S.; Suzuki, Y.; Yagi, N.

2001-01-01

We propose a new X-ray methodology for direct observations of the behaviors of single molecular units in real time and real space. This new system, which we call Diffracted X-ray Tracking (DXT), monitors the Brownian motions of a single molecular unit by observations of X-ray diffracted spots from a nanocrystal, tightly bound to the individual single molecular unit in bio-systems. DXT does not determine any translational movements, but only orientational movements

Immediate renal imaging and renography with /sup 99m/Tc methylene diphosphonate to assess renal blood flow, excretory function, and anatomy

International Nuclear Information System (INIS)

Glass, E.C.; DeNardo, G.L.; Hines, H.H.

1980-01-01

/sup 99m/Tc methylene diphosphonate (/sup 99m/Tc MDP) was evaluated as a clinical renal imaging agent in 20 patients referred for bone scintigraphy. Sequential scintigraphy, which was started immediately after injection, yielded blood flow studies of high quality, and subsequent images accurately delineated renal anatomy and excretion in nonazotemic patients. In comparison with delayed images, early images were vastly superior in quality and demonstrated improved target-to-nontarget activity ratios (p < 0.001) and improved lesion detectability (p < 0.01). Renal imaging performed incidental to bone scintigraphy with MDP can be greatly enhanced by initiating sequential scintigraphy immediately after injection

Adsorption of methylene blue dye from aqueous solution by sugar extracted spent rice biomass.

Science.gov (United States)

Ur Rehman, Muhammad Saif; Kim, Ilgook; Han, Jong-In

2012-10-15

This study was aimed at using sugar extracted spent rice biomass (SRB) as a potential adsorbent to remove methylene blue (MB) dye from aqueous solution. The SRB was used without any modification. A three factor full factorial experimental design (2(3)) was employed to investigate the effect of factors (adsorbent dose, dye concentration, temperature) and their interaction on the adsorption capacity and color removal. Two levels for each factor were used; adsorbent dose (0.25-0.5g/100mL), dye concentration (25-50mg/L), and temperature (25-45°C). Initial dye concentration and adsorbent dosage were found as significant factors for the adsorption of MB dye. Langmuir isotherm (R(2)>0.998) best explained the equilibrium of MB adsorption on SRB with monolayer adsorption capacity of 8.13mg/g. The pseudo-second order model (R(2)>0.999) was best fitted to explain the adsorption kinetics. Thermodynamic investigation revealed that the adsorption process was spontaneous, endothermic, and was feasible to treat dyeing wastewater. Copyright © 2012 Elsevier Ltd. All rights reserved.

Decolorization of Methylene Blue by Ag/SrSnO3 Composites under Ultraviolet Radiation

Directory of Open Access Journals (Sweden)

Patcharanan Junploy

2014-01-01

Full Text Available SrSn(OH6 precursors synthesized by a cyclic microwave radiation (CMR process were calcined at 900°C for 3 h to form rod-like SrSnO3. Further, the rod-like SrSnO3 and AgNO3 in ethylene glycol (EG were ultrasonically vibrated to form rod-like Ag/SrSnO3 composites, characterized by X-ray diffraction (XRD, X-ray photoelectron spectroscopy (XPS, electron microscopy (EM, Fourier transform infrared (FTIR spectroscopy, and UV-visible analysis. The photocatalyses of rod-like SrSnO3, 1 wt%, 5 wt%, and 10 wt% Ag/SrSnO3 composites were studied for degradation of methylene blue (MB, C16H18N3SCl dye under ultraviolet (UV radiation. In this research, the 5 wt% Ag/SrSnO3 composites showed the highest activity, enhanced by the electron-hole separation process. The photoactivity became lower by the excessive Ag nanoparticles due to the negative effect caused by reduction in the absorption of UV radiation.

Potential biosorbent, Haloxylon recurvum plant stems, for the removal of methylene blue dye

Directory of Open Access Journals (Sweden)

Warda Hassan

2017-05-01

Full Text Available Conventional technologies for the removal of dyes from the waste water are proving expensive due to non-regenerable materials used and their high costs. The use of dried biomass from Haloxylon recurvum plant stems (HRS was studied for the removal of methylene blue, a textile dye, from its aqueous solution. FTIR studies revealed a variety of functional groups on the plant surface including carboxyl and amino groups. The pH at the point of zero charge (pHpzc was found to be 6.3. The dye uptake by the plant increased with increasing pH, time of contact and dye concentration. Lagergren Pseudo first order and the Ho’s pseudo second order models were used to study the kinetics. The Langmuir and Freundlich equilibrium models were studied and the qmax was 22.93 mg/g. The changes in the values of free energy (ΔGo and enthalpy (ΔHo indicated the spontaneous, feasible and exothermic nature of the sorption process. H. recurvum plant is locally available in large quantities, so the powdered stems can act as a cost-effective and ecofriendly biosorbent for the removal of the dye from its aqueous solutions.

Adsorption and photodegradation of methylene blue on TiO{sub 2}-halloysite adsorbents

Energy Technology Data Exchange (ETDEWEB)

Du, Yuanyuan; Zheng, Pengwu [Jiangxi Science and Technology Normal University, Nanchang (China)

2014-11-15

TiO{sub 2}-halloysite (TiO{sub 2}-HNT) composites were fabricated by depositing anatase TiO{sub 2} on the halloysite (HNT) surfaces with calcination treatment at 100, 200, 300 and 500 .deg. C. The obtained composites were characterized by transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR) and X-Ray diffraction (XRD). HNT was attached with TiO{sub 2} particles or clusters in sizes of 10-30 nm. With the increasing of calcination temperature, the crystalline of anatase became more perfect, but the structure of HNT could be destroyed at 500 .deg. C. The adsorption and photodegradation of methylene blue (MB) by TiO{sub 2}-HNTs were investigated. The kinetic adsorption fit the pseudo second-order, and the isotherm data followed the Langmuir model. The maximum adsorption capacities of MB were in the range of 38.57 to 54.29 mg/g. TiO{sub 2}-HNTs exhibited an efficient photocatalytic activity in the decomposition of MB. For TiO{sub 2}-HNT calcined at 300 .deg. C, 81.6% MB were degraded after 4 h treatment of UV irradiation.

Optimization of methylene blue removal by stable emulsified liquid membrane using Plackett–Burman and Box–Behnken designs of experiments

Science.gov (United States)

Djenouhat, Meriem; Bendebane, Farida; Bahloul, Lynda; Samar, Mohamed E. H.

2018-01-01

The stability of an emulsified liquid membrane composed of Span80 as a surfactant, D2EHPA as an extractant and sulfuric acid as an internal phase was first studied according to different diluents and many operating parameters using the Plackett–Burman design of experiments. Then the removal of methylene blue from an aqueous solution has been carried out using this emulsified liquid membrane at its stability conditions. The effects of operating parameters were analysed from the Box–Behnken design of experiments. The optimization of the extraction has been realized applying the response surface methodology and the results showed that the dye extraction yielding 98.72% was achieved at optimized conditions. PMID:29515841

Effect of preparation convergence on retention of multiple unit restorations - An in vitrostudy

Directory of Open Access Journals (Sweden)

Dileep Nag Vinnakota

2015-01-01

Full Text Available Background and Aim: Convergence angle (CA is one of the major determinant factors in the retention of single as well as multiple units. Hence, the aim of the present study was to determine the effect of preparation convergence on the retention of multiple unit restorations. Materials and Methods: Nickel-chromium alloy single crowns as well as three, six and nine multiple unit fixed partial dentures (FPDs were casted for standardized milled dies that simulate canine, premolar and molar teeth machined with two different degrees of convergence, 12 (n = 55 and 20 (n = 55. The dies were threaded on rectangular metal platforms with the help of retainer shaft in the proper position to model either single or multiple preparations. The casted crowns and FPDs were cemented and retention tested by securing the units in an Instron universal testing machine. The tabulated values were analyzed statistically using Mann-Whitney test. Results: Single and multiple units with 12° CA needed greater force to dislodge compared to 20°, but this difference was not statistically significant for single units of premolar (P > 0.05. Irrespective of the angle, there was a simultaneous statistically significant increase in retention as the number of units increased in FPDs, except for the difference between 3 and 6 units in 20° group (P > 0.05. Conclusion: This study highlights the importance of emphasizing on CA, during canine and molar preparation for single units as well as preparation of canines for 6 units FPDs.

Adsorptive Removal of Methylene Blue onto ZnCl2 Activated Carbon from Wood Apple Outer Shell: Kinetics and Equilibrium Studies

Directory of Open Access Journals (Sweden)

N. Bhadusha

2011-01-01

Full Text Available Methylene blue dye removal from aqueous solution was investigated using ZnCl2 activated carbon prepared from wood apple outer shell (Limonia acidissima, biomass waste. Influence of agitation time, adsorbent dose, dye concentration, pH and temperature were explored. Two theoretical adsorption isotherms namely Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Qo was found to be 35.1 mg/g and the equilibrium parameter (RL values indicate favourable adsorption. The experimental data were well fitted with Langmuir isotherm model and pseudo second order kinetic model. Desorption studies showed that ion exchange mechanism might be involved in the adsorption process.

Expeditious Entry to Novel 2-Methylene-2,3-dihydrofuro[3,2-c] chromen-2-ones from 6-Chloro-4-hydroxychromen-2-one and Propargylic Alcohols

Directory of Open Access Journals (Sweden)

Josefina Díez

2011-08-01

Full Text Available A catalytic system consisting of the ruthenium(II complex [Ru(η3-2-C3H4Me(CO(dppf][SbF6] (dppf = 1,1’-bis(diphenylphosphinoferrocene and trifluoroacetic acid has been used to promote the coupling of secondary propargylic alcohols with 6-chloro-4-hydroxychromen-2-one. The reactions afforded unusual 2-methylene-2,3-dihydrofuro[3,2-c]chromen-2-ones in good yields.

Modeling Heat Transfer and Pressurization of Polymeric Methylene Diisocyanate (PMDI) Polyurethane Foam in a Sealed Container.

Energy Technology Data Exchange (ETDEWEB)

Scott, Sarah Nicole

2018-01-01

Polymer foam encapsulants provide mechanical, electrical, and thermal isolation in engineered systems. It can be advantageous to surround objects of interest, such as electronics, with foams in a hermetically sealed container to protect the electronics from hostile en vironments, such as a crash that produces a fire. However, i n fire environments, gas pressure from thermal decomposition of foams can cause mechanical failure of the sealed system . In this work, a detailed study of thermally decomposing polymeric methylene diisocyanate (PMDI) - polyether - polyol based polyurethane foam in a sealed container is presented . Both experimental and computational work is discussed. Three models of increasing physics fidelity are presented: No Flow, Porous Media, and Porous Media with VLE. Each model us described in detail, compared to experiment , and uncertainty quantification is performed. While the Porous Media with VLE model matches has the best agreement with experiment, it also requires the most computational resources.

Flexible Bench-Scale Recirculating Flow CPC Photoreactor for Solar Photocatalytic Degradation of Methylene Blue Using Removable TiO2 Immobilized on PET Sheets

Directory of Open Access Journals (Sweden)

Doaa M. EL-Mekkawi

2016-01-01

Full Text Available TiO2 immobilized on polyethylene (PET nonwoven sheet was used in the solar photocatalytic degradation of methylene blue (MB. TiO2 Evonik Aeroxide P25 was used in this study. The amount of loaded TiO2 on PET was approximately 24%. Immobilization of TiO2 on PET was conducted by dip coating process followed by exposing to mild heat and pressure. TiO2/PET sheets were wrapped on removable Teflon rods inside home-made bench-scale recirculating flow Compound Parabolic Concentrator (CPC photoreactor prototype (platform 0.7 × 0.2 × 0.4 m3. CPC photoreactor is made up of seven low iron borosilicate glass tubes connected in series. CPC reflectors are made of stainless steel 304. The prototype was mounted on a platform tilted at 30°N local latitude in Cairo. A centrifugal pump was used to circulate water containing methylene blue (MB dye inside the glass tubes. Efficient photocatalytic degradation of MB using TiO2/PET was achieved upon the exposure to direct sunlight. Chemical oxygen demand (COD analyses reveal the complete mineralization of MB. Durability of TiO2/PET composite was also tested under sunlight irradiation. Results indicate only 6% reduction in the amount of TiO2 after seven cycles. No significant change was observed for the physicochemical characteristics of TiO2/PET after the successive irradiation processes.

Wiring of Glucose Oxidizing Flavin Adenine Dinucleotide-Dependent Enzymes by Methylene Blue-Modified Third Generation Poly(amidoamine) Dendrimers Attached to Spectroscopic Graphite Electrodes

International Nuclear Information System (INIS)

Castaing, Victor; Álvarez-Martos, Isabel; Ferapontova, Elena E.

2016-01-01

Highlights: • Methylene blue(MB)-labelled 3 G dendrimers electronically wire flavoenzymes to graphite electrodes. • Dendrimer-templated organization of MB improves electron transfer efficiency. • Covalent attachment of dendrimers to graphite provides stability of binding superior to S-Au. • Sugar-oxidizing hexose oxidase can be wired with no loss of FAD and electrocatalytic activity. - Abstract: Electro-enzymatic biotransformation requires an efficient and robust electronic communication between the biomolecules and electrodes, often performed by the relevant electron transfer (ET) mediating systems. Of those, redox-labeled dendrimeric structures, biocompatible and bearing spatially ordered multiple redox centers, represent an advanced alternative to the existing approaches. Here we show that methylene blue (MB)-labeled G3 PAMAM dendrimers covalently attached to the high-surface area spectroscopic graphite (Gr) electrodes form stable and spatially resolved electronic wires, characterized by the heterogeneous ET rate constant of 7.1 ± 0.1 s"−"1; they can be used for electronic wiring of glucose-oxidizing FAD-containing enzymes, such as hexose oxidase (HOX), and further bioelectrocatalysis of glucose oxidation, starting, at pH 7, from -100 mV vs. Ag/AgCl. Thus, dendrimer-templated electronic wires, comprising MB molecules conjugated to the periphery of the PAMAM and anchored to the surface of cost-effective Gr electrodes represent an efficient and robust tool for protein wiring to electrodes for their perspective bioelectronic applications in biosensors and biofuel cells.

Chlorinated solvents in groundwater of the United States

Science.gov (United States)

Moran, M.J.; Zogorski, J.S.; Squillace, P.J.

2007-01-01

Four chlorinated solvents-methylene chloride, perchloroethene (PCE), 1,1,1-trichloroethane, and trichloroethene (TCE)-were analyzed in samples of groundwater taken throughout the conterminous United States by the U.S. Geological Survey. The samples were collected between 1985 and 2002 from more than 5,000 wells. Of 55 volatile organic compounds (VOCs) analyzed in groundwater samples, solvents were among the most frequently detected. Mixtures of solvents in groundwater were common and may be the result of common usage of solvents or degradation of one solvent to another. Relative to other VOCs with Maximum Contaminant Levels (MCLs), PCE and TCE ranked high in terms of the frequencies of concentrations greater than or near MCLs. The probability of occurrence of solvents in groundwater was associated with dissolved oxygen content of groundwater, sources such as urban land use and population density, and hydraulic properties of the aquifer. The results reinforce the importance of understanding the redox conditions of aquifers and the hydraulic properties of the saturated and vadose zones in determining the intrinsic susceptibility of groundwater to contamination by solvents. The results also reinforce the importance of controlling sources of solvents to groundwater. ?? 2007 American Chemical Society.

Analysis of molecular species of triacylglycerols from vegetable oils containing fatty acids with non-methylene-interrupted double bonds, by HPLC in the silver-ion mode

Energy Technology Data Exchange (ETDEWEB)

Joh, Y.; Kim, S. [Dong A Univ., Pusan (Korea, Republic of)

1998-10-20

The possibilities for application of silver ion HPLC to analysis of the triacylglycerols containing conjugate trienoic acids and {Delta}{sup 5}-polymethylene-interrupted acids and proportions of triacylglycerol fractions obtained by silver-ion HPLC from the seed oil of Momordica charantia double bonds were examined, respectively. The triacylglycerols of seed oils containing conjugate trienoic acids such as {alpha}-eleostearic acid (C{sub 18:3 9c,11t,13t}) and punicic acid (C{sub 18:3} {sub 9c,11t,13c}) were resolved by silver-ion HPLC. Fractions were fractionated on the basis of the number and configuration of double bonds in the species, and the elution profile is quite different from that of the species comprising exclusively saturated and unsaturated fatty acids with methylene-interrupted double bonds ; for instance, the species (DT(c2)) composed of one dienoic acid and two conjugate trienoic acids eluted much earlier than the species (D{sub 2}T{sub c}) composed of two dienoic acids and one conjugate trienoic acid, in spite of having larger number of double bonds. This means that the interaction of conjugate double bonds with silver ions is weaker than that of methylene-interrupted double bonds, presumably because of the delocalization of {pi}-electrons in conjugate double bonds. In this instance, the strength of interaction of a conjugate trienoic double bond system with silver ions seemed to be between that of methylene-interrupted dienoic and monoenoic double bond systems. Triacylglycerols of the seeds of Ginkgo biloba have been resolved by HPLC in the silver-ion mode according to the number and position of double bonds. In this instance, the strength of interaction between the {pi}-electrons of double bonds in the fatty acyl residues and silver ions is in the order; C{sub 18:3{omega}3}>C(20:3){Delta}{sup 5,11,14}C{sub 18:3}{Delta}{sup 5,9,12}>= C{sub 18:2{omega}6}>C{sub 18:2}{Delta}{sup 5,9}>C{sub 18:1{omega}9}>C{sub 18:1ome= ga7}. 49 refs., 2 figs., 2 tabs.

1:250,000-scale Hydrologic Units of the United States

Science.gov (United States)

Steeves, Peter; Nebert, Douglas

1994-01-01

The Geographic Information Retrieval and Analysis System (GIRAS) was developed in the mid 70s to put into digital form a numberof data layers which were of interest to the USGS. One of these data layers was the Hydrologic Units. The map is based on the Hydrologic Unit Maps published by the U.S. Geological Survey Office of Water Data Coordination, together with the list descriptions and name of region, subregion, accounting units, and cataloging unit. The hydrologic units are encoded with an eight-digit number that indicates the hydrologic region (first two digits), hydrologic subregion (second two digits), accounting unit (third two digits), and cataloging unit (fourth two digits). The data produced by GIRAS was originally collected at a scale of 1:250K. Some areas, notably major cities in the west, were recompiled at a scale of 1:100K. In order to join the data together and use the data in a geographic information system (GIS) the data were processed in the ARC/INFO GUS software package. Within the GIS, the data were edgematched and the neatline boundaries between maps were removed to create a single data set for the conterminous

Single-Chain Folding of Synthetic Polymers: A Critical Update.

Science.gov (United States)

Altintas, Ozcan; Barner-Kowollik, Christopher

2015-11-23

The current contribution serves as a critical update to a previous feature article from us (Macromol. Rapid Commun. 2012, 33, 958-971), and highlights the latest advances in the preparation of single chain polymeric nanoparticles and initial-yet promising-attempts towards mimicking the structure of natural biomacromolecules via single-chain folding of well-defined linear polymers via so-called single chain selective point folding and repeat unit folding. The contribution covers selected examples from the literature published up to ca. September 2015. Our aim is not to provide an exhaustive review but rather highlight a selection of new and exciting examples for single-chain folding based on advanced macromolecular precision chemistry. Initially, the discussion focuses on the synthesis and characterization of single-chain folded structures via selective point folding. The second part of the feature article addresses the folding of well-defined single-chain polymers by means of repeat unit folding. The current state of the art in the field of single-chain folding indicates that repeat unit folding-driven nanoparticle preparation is well-advanced, while initial encouraging steps towards building selective point folding systems have been taken. In addition, a summary of the-in our view-open key questions is provided that may guide future biomimetic design efforts. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Preparation of nitrogen-doped cotton stalk microporous activated carbon fiber electrodes with different surface area from hexamethylenetetramine-modified cotton stalk for electrochemical degradation of methylene blue

Directory of Open Access Journals (Sweden)

Kunquan Li

Full Text Available Cotton-stalk activated carbon fibers (CSCFs with controllable micropore area and nitrogen content were prepared as an efficient electrode from hexamethylenetetramine-modified cotton stalk by steam/ammonia activation. The influence of microporous area, nitrogen content, voltage and initial concentration on the electrical degradation efficiency of methylene blue (MB was evaluated by using CSCFs as anode. Results showed that the CSCF electrodes exhibited excellent MB electrochemical degradation ability including decolorization and COD removal. Increasing micropore surface area and nitrogen content of CSCF anode leaded to a corresponding increase in MB removal. The prepared CSCF-800-15-N, which has highest N content but lowest microporous area, attained the best degradation effect with 97% MB decolorization ratio for 5 mg/L MB at 12 V in 4 h, implying the doped nitrogen played a prominent role in improving the electrochemical degradation ability. The electrical degradation reaction was well described by first-order kinetics model. Overall, the aforesaid findings suggested that the nitrogen-doped CSCFs were potential electrode materials, and their electrical degradation abilities could be effectively enhanced by controlling the nitrogen content and micropore surface area. Keywords: Cotton stalk, Nitrogen content, Electrode, Surface area, Methylene blue

Color measurement of methylene blue dye/clay mixtures and its application using economical methods

Science.gov (United States)

Milosevic, Maja; Kaludjerovic, Lazar; Logar, Mihovil

2016-04-01

Identifying the clay mineral components of clay materials by staining tests is rapid and simple, but their applicability is restricted because of the mutual interference of the common components of clay materials and difficulties in color determination. The change of color with concentration of the dye is related to the use of colorants as a field test for identifying clay minerals and has been improved over the years to assure the accuracy of the tests (Faust G. T., 1940). The problem of measurement and standardization of color may be solved by combination of colors observed in staining tests with prepared charts of color chips available in the Munsell Book of Color, published by Munsell Color Co. Under a particular set of illumination conditions, a human eye can achieve an approximate match between the color of the dyed clay sample and that of a standard color chip, even though they do have different spectral reflectance characteristics. Experiments were carried out with diffuse reflectance spectroscopy on selected clay samples (three montmorillonite, three kaolinite and one mix-layer clay samples) saturated with different concentration of methylene blue dye solution. Dominant wavelength and purity of the color was obtained on oriented dry samples and calculated by use of the I. C. I. (x, y) - diagram in the region of 400-700 nm (reflectance spectra) without MB and after saturation with different concentrations of MB solutions. Samples were carefully photographed in the natural light environment and processed with user friendly and easily accessible applications (Adobe color CC and ColorHexa encyclopedia) available for android phones or tablets. Obtained colors were compared with Munsell standard color chips, RGB and Hexa color standards. Changes in the color of clay samples in their interaction with different concentration of the applied dye together with application of economical methods can still be used as a rapid fieldwork test. Different types of clay

Laccase immobilized on methylene blue modified mesoporous silica MCM-41/PVA

International Nuclear Information System (INIS)

Xu Xinhua; Lu Ping; Zhou Yumei; Zhao Zhenzhen; Guo Meiqing

2009-01-01

The mesoporous silica sieve MCM-41 containing methylene blue (MB) provides a suitable immobilization of biomolecule matrix due to its uniform pore structure, high surface areas, good biocompatibility and nice conductivity. Based on this, a facilely fabricated amperometric biosensor by entrapping laccase into the MB modified MCM-41/PVA composite film has been developed. Laccase from Trametes versicolor is assembled on a composite film of MCM-41 containing MB/PVA modified Au electrode and the electrode is characterized with respect to transmission electron microscopy (TEM) and scanning electron microscopic (SEM), Cyclic voltammetry (CV), response time, detection limit, linear range and activity of laccase. The laccase modified electrode remains good redox behavior in pH 4.95 acetate buffer solution, at room temperature in present of 0.1 mM catechol. The response time (t 90% ) of the modified electrode is less than 4 s for catechol. The detection limit is 0.331 μM and the linear detect range is about from 4.0 μM to 87.98 μM for catechol with a correlation coefficient of 0.99913(S/N = 3). The apparent Michaelis-Menten (K M app ) is estimated using the Lineweaver-Burk equation and the K M app value is about 0.256 mM. This work demonstrated that the mesoporous silica MCM-41 containing MB provides a novel support for laccase immobilization and the construction of biosensors with a faster response and better bioactivity.

An Asynchronous IEEE Floating-Point Arithmetic Unit

Directory of Open Access Journals (Sweden)

Joel R. Noche

2007-12-01

Full Text Available An asynchronous floating-point arithmetic unit is designed and tested at the transistor level usingCadence software. It uses CMOS (complementary metal oxide semiconductor and DCVS (differentialcascode voltage switch logic in a 0.35 µm process using a 3.3 V supply voltage, with dual-rail data andsingle-rail control signals using four-phase handshaking.Using 17,085 transistors, the unit handles single-precision (32-bit addition/subtraction, multiplication,division, and remainder using the IEEE 754-1985 Standard for Binary Floating-Point Arithmetic, withrounding and other operations to be handled by separate hardware or software. Division and remainderare done using a restoring subtractive algorithm; multiplication uses an additive algorithm. Exceptionsare noted by flags (and not trap handlers and the output is in single-precision.Previous work on asynchronous floating-point arithmetic units have mostly focused on single operationssuch as division. This is the first work to the authors' knowledge that can perform floating-point addition,multiplication, division, and remainder using a common datapath.

Structure of methylene chloride addition product to zirconium tetrachloride complex with 1-tert.-butyl-2,4,4-trimethyl-2-thio-trimethylsilyl-1,3,2,4-diazaphosphasilatedine

International Nuclear Information System (INIS)

Brusilovets, A.I.; Rusanov, Eh.B.; Chernega, A.N.

1995-01-01

Complex of zirconium tetrachloride with 1-tert.-butyl-2,4,4-trimethyl--2-thio-3-trimethyl-silyl-1,3,2,4-diazaphosphasilatedine interacts with methylene chloride with formation of bis[3-tert.-butyl-2,4,4-trimethyl-1--trimethylsilyl-2-chloremethylthio-1,3,2,4-diazaphosphasilatedinium] decachlorodizirconate. Specific features of crystal and molecular structure of the compound prepared have been studied by X-ray diffraction method. 21 refs.; 2 figs.; 2 tabs

Silver-gold core-shell nanoparticles containing methylene blue as SERS labels for probing and imaging of live cells

International Nuclear Information System (INIS)

Guo, X.; Guo, Z.; Jin, Y.; Liu, Z.; Zhang, W.; Huang, D.

2012-01-01

We report on silver-gold core-shell nanostructures that contain Methylene Blue (MB) at the gold/x96silver interface. They can be used as reporter molecules in surface-enhanced Raman scattering (SERS) labels. The labels are stable and have strong SERS activity. TEM imaging revealed that these nanoparticles display bright and dark stripe structures. In addition, these labels can act as probes that can be detected and imaged through the specific Raman signatures of the reporters. We show that such SERS probes can identify cellular structures due to enhanced Raman spectra of intrinsic cellular molecules measured in the local optical fields of the core-shell nanostructures. They also provide structural information on the cellular environment as demonstrated for these nanoparticles as new SERS-active and biocompatible substrates for imaging of live cells. (author)

16-channel analog store and multiplexer unit

Energy Technology Data Exchange (ETDEWEB)

Brossard, M; Kulka, Z [Clermont-Ferrand-2 Univ., 63 - Aubiere (France). Lab. de Physique Corpusculaire

1979-03-15

A 16-channel analog store and multiplexer unit is described. The unit enables storing and selection of analog information which is then digitally encoded by single ADC. This solution becomes economically attractive particularly in multidetector pulse height analysis systems.

A novel algorithm for demand-control of a single-room ventilation unit with a rotary heat exchanger

DEFF Research Database (Denmark)

Smith, Kevin Michael; Jansen, Anders Lund; Svendsen, Svend

in the indoor environment. Based on these values, a demand-control algorithm varies fan speeds to change airflow rates and varies the rotational speed of the heat exchanger to modulate heat and moisture recovery. The algorithm varies airflow rates to provide free cooling and limit CO2 concentrations and varies...... moisture recovery by varying the rotational speed and then safely unbalances airflows in a worst-case scenario. In the algorithm, frost protection and minimum supply temperature take the highest priority and override other controls. This paper documents the proposed demand control algorithm and analyses...... its impacts on compliance of building regulations in Denmark. The paper presents an algorithm that manufacturers can program into their controls. The commercially available single-room ventilation unit with a rotary heat exchanger uses this algorithm coded in the C language. Future work will document...

Optimization of microwave-assisted durian seed based activated carbon preparation conditions for methylene blue dye removal

Science.gov (United States)

Ahmad, Mohd Azmier; Hamid, Siti Ruqayyah Ab.; Yusop, Mohamad Firdaus Mohamad; Aziz, Hamidi Abdul

2017-10-01

Due to easy access and relatively high fixed carbon content of 26.13% in its raw form, durian seed based activated carbon (DSAC) was produced via microwave heating. For activation stage, physiochemical approach consist of carbon dioxide (CO2) gasification and potassium hydroxide (KOH) as chemical activator were employed. Three most influential preparation variables on adsorption performance and yield of activated carbon (AC), which is radiation power, radiation time and KOH impregnation ratio (IR) were optimized with the help of response surface methodology (RSM). The optimization result revealed that 440W, 4.0 minutes and 0.55 of radiation power, radiation time and IR respectively, were needed to remove 80.23% of methylene blue (MB) dye and to obtain 25.77% of DSAC's yield. High Brunauer-Emmet-Teller (BET) surface area, total pore volume and average pore size of 852.30m2/g, 0.465cm3/g and 3.74nm respectively, were obtained on optimized DSAC.

Removal of Methylene Blue from Aqueous Solution by Activated Carbon Prepared from Pea Shells (Pisum sativum

Directory of Open Access Journals (Sweden)

Ünal Geçgel

2013-01-01

Full Text Available An activated carbon was prepared from pea shells and used for the removal of methylene blue (MB from aqueous solutions. The influence of various factors such as adsorbent concentration, initial dye concentration, temperature, contact time, pH, and surfactant was studied. The experimental data were analyzed by the Langmuir and Freundlich models of adsorption. The adsorption isotherm was found to follow the Langmuir model. The monolayer sorption capacity of activated carbon prepared from pea shell for MB was found to be 246.91 mg g−1 at 25 ∘C. Two simplified kinetic models including pseudo-first-order and pseudo-second-order equation were selected to follow the adsorption processes. Kinetic studies showed that the adsorption followed pseudo-second-order kinetic model. Various thermodynamic parameters such as , , and were evaluated. The results in this study indicated that activated carbon prepared from pea shell could be employed as an adsorbent for the removal of MB from aqueous solutions.

Well-ordered structure of methylene blue monolayers on Au(111) surface: electrochemical scanning tunneling microscopy studies.

Science.gov (United States)

Song, Yonghai; Wang, Li

2009-02-01

Well-ordered structure of methylene blue (MB) monolayers on Au(111) surface has been successfully obtained by controlling the substrate potential. Electrochemical scanning tunneling microscopy (ECSTM) examined the monolayers of MB on Au(111) in 0.1 M HClO(4) and showed long-range ordered, interweaved arrays of MB with quadratic symmetry on the substrate in the potential range of double-layer charging. High-resolution ECSTM image further revealed the details of the MB monolayers structure of c(5 x 5 radical 3)rect and the flat-lying orientation of ad-molecules. The dependence of molecular organization on the substrate potential and the formation mechanism of well-ordered structure on Au(111) surface were investigated in detail. The obtained well-ordered structure at the interface between a metal and an aqueous electrolyte might possibly be used as high-density device for signal memory and templates for the advanced nanopatterning of surfaces. (c) 2008 Wiley-Liss, Inc.

Biosorption of methylene blue from aqueous solution by fallen phoenix tree's leaves

International Nuclear Information System (INIS)

Han Runping; Zou Weihua; Yu Weihong; Cheng Shujian; Wang Yuanfeng; Shi Jie

2007-01-01

A new adsorbent, the fallen phoenix tree's leaf, has been investigated in order to remove methylene blue (MB) from aqueous solutions. Variables of the system, including contact time, leaf dose, solution pH, salt concentration and initial MB concentration, were adopted to study their effects on MB biosorption. The results showed that as the dose of leaf increased, the percentage of MB sorption increased accordingly. There was no significant difference about the quantity of MB adsorbed onto leaf as the pH was within the range 4.5-10.0. The salt concentration has negative effect on MB removal. The equilibrium data were analyzed using the Langmuir and the Freundlich isotherms. The results of non-linear regressive analysis are that the Langmuir isotherm is better fit than the Freundlich isotherm at different temperature according to the values of determined coefficients (R 2 ) and χ 2 -statistic (SS). The Langmuir monolayer saturation capacities of MB adsorbed onto leaf are 80.9, 83.8, 89.7 mg g -1 at 295, 309 and 323 K, respectively. Using the equilibrium concentration contents obtained at different temperatures, various thermodynamic parameters, such as ΔG o , ΔH o and ΔS o , have been calculated. The thermodynamics parameters of MB/leaf system indicate spontaneous and endothermic process. It was concluded that an increase in temperature be advantage to adsorb MB onto leaf

Health care access and utilization among children of single working and nonworking mothers in the United States.

Science.gov (United States)

Clarke, Tainya C; Arheart, Kristopher L; Muennig, Peter; Fleming, Lora E; Caban-Martinez, Alberto J; Dietz, Noella; Lee, David J

2011-01-01

To examine indicators of health care access and utilization among children of working and nonworking single mothers in the United States, the authors used data on unmarried women participating in the 1997-2008 National Health Interview Survey who financially supported children under 18 years of age (n = 21,842). Stratified by maternal employment, the analyses assessed health care access and utilization for all children. Outcome variables included delayed care, unmet care, lack of prescription medication, no usual place of care, no well-child visit, and no doctor's visit. The analyses reveal that maternal employment status was not associated with health care access and utilization. The strongest predictors of low access/utilization included no health insurance and intermittent health insurance in the previous 12 months, relative to those with continuous private health insurance coverage (odds ratio ranges 3.2-13.5 and 1.3-10.3, respectively). Children with continuous public health insurance compared favorably with those having continuous private health insurance on three of six access/utilization indicators (odds ratio range 0.63-0.85). As these results show, health care access and utilization for the children of single mothers are not optimal. Passage of the U.S. Healthcare Reform Bill (HR 3590) will probably increase the number of children with health insurance and improve these indicators.

Multi-Unit Aspects of the Pickering Generating Station

Energy Technology Data Exchange (ETDEWEB)

Morison, W. G. [Atomic Energy of Canada Ltd, Sheridan Park, ON (Canada)

1968-04-15

The Pickering nuclear generating station is located on the north shore of Lake Ontario, about 20 miles east of the city of Toronto, Canada. The station has been planned and laid out on an eight-unit station, four units of which have now been authorized for construction. Each of these four units consists of a single heavy-water moderated and cooled CANDU-type reactor and auxiliaries coupled to a single tandem compound turbine generator with a net output of approximately 500 MW(e). The units are identical and are scheduled to come into operation at intervals of one year from 1970 to 1973. The station has been planned with central facilities for: administration maintenance laboratories, stores, change rooms, decontamination and waste management services. A common control centre, cooling water intake and discharge system, and spent fuel storage bay for four units has been arranged. A feature of the multi-unit station is a common containment system. Cost savings in building a number of identical units on the same site result from a single exclusion area, shared engineering costs, equipment purchase contracts for four identical components, and efficient use of construction plant. Operating cost savings are anticipated in the use of a common operating and maintenance staff and spare parts inventory. The plant has been arranged to minimize problems of operating, commissioning and constructing units at the same time on the same site. The layout and construction sequence have been arranged so that the first unit can be commissioned and operated with little or no interference from the construction forces working on succeeding units. During the construction phase barriers will be erected in the common control centre between operating control equipment and that being installed. Operations and construction personnel will enter the plant by separate routes and work in areas separated by physical barriers. (author)

Attaching NorA efflux pump inhibitors to methylene blue enhances antimicrobial photodynamic inactivation of Escherichia coli and Acinetobacter baumannii in vitro and in vivo.

Science.gov (United States)

Rineh, Ardeshir; Bremner, John B; Hamblin, Michael R; Ball, Anthony R; Tegos, George P; Kelso, Michael J

2018-02-24

Resistance of bacteria to antibiotics is a public health concern worldwide due to the increasing failure of standard antibiotic therapies. Antimicrobial photodynamic inactivation (aPDI) is a promising non-antibiotic alternative for treating localized bacterial infections that uses non-toxic photosensitizers and harmless visible light to produce reactive oxygen species and kill microbes. Phenothiazinium photosensitizers like methylene blue (MB) and toluidine blue O are hydrophobic cations that are naturally expelled from bacterial cells by multidrug efflux pumps, which reduces their effectiveness. We recently reported the discovery of a NorA efflux pump inhibitor-methylene blue (EPI-MB) hybrid compound INF55-(Ac)en-MB that shows enhanced photodynamic inactivation of the Gram-positive bacterium methicillin-resistant Staphylococcus aureus (MRSA) relative to MB, both in vitro and in vivo. Here, we report the surprising observation that INF55-(Ac)en-MB and two related hybrids bearing the NorA efflux pump inhibitors INF55 and INF271 also show enhanced aPDI activity in vitro (relative to MB) against the Gram-negative bacteria Escherichia coli and Acinetobacter baumannii, despite neither species expressing the NorA pump. Two of the hybrids showed superior effects to MB in murine aPDI infection models. The findings motivate wider exploration of aPDI with EPI-MB hybrids against Gram-negative pathogens and more detailed studies into the molecular mechanisms underpinning their activity. Copyright © 2018 Elsevier Ltd. All rights reserved.

Optimization of microwave-assisted rubberwood sawdust based activated carbon preparation conditions for methylene blue removal

Science.gov (United States)

Khasri, Azduwin; Ahmad, Mohd Azmier

2017-10-01

Optimum preparation conditions of rubberwood sawdust based activated carbon (RSAC) for methylene blue (MB) dye removal was studied. RSAC was produced by applying physiochemical activation method by using potassium hydroxide as a chemical agent which accompanied by carbon dioxide gasification under microwave heating. The effects of microwave power, irradiation time and impregnation ratio on two types of responses namely MB removal and RSAC yield using the center composite design (CCD) were also included in this study. The preparation variables correlation for responses was developed by two quadratic models. Optimum preparation conditions of RSAC were obtained at microwave power, irradiation time and IR of 354 W, 4.5 minutes and 0.98, respectively, which resulted MB removal and yield of 83.79% and 28%, respectively. The average pore diameter, surface area and total pore volume of optimized RSAC were 4.12 nm, 796.33 m2/g and 0.4219 cm3/g, respectively. This sample was found to has well-developed pores on its surface and can be a promising adsorbent for MB removal from aqueous solution.

TiO₂ (rutile) embedded inulin--A versatile bio-nanocomposite for photocatalytic degradation of methylene blue.

Science.gov (United States)

Jayanthi Kalaivani, G; Suja, S K

2016-06-05

Inulin, a water soluble carbohydrate polymer, was extracted from Allium sativum L. by hot water diffusion method. A novel bio-nanocomposite was prepared by embedding TiO2 (rutile) onto the inulin matrix. The extracted inulin and the prepared bio-nanocomposite were characterized using UV-vis, FT-IR, XRD, SEM, TEM and TGA techniques. The photocatalytic activity of the bio-nanocomposite for the degradation of methylene blue was studied under UV illumination in batch mode experiment and was found to be twice as high as that of pristine TiO2. The kapp for inulin-TiO2 (0.0449 min(-1)) was higher than that for TiO2 (0.0325 min(-1)) which may be due to the synergistic action of inulin and TiO2. The stabilization of photo excited electron suppressed the electron-hole pair recombination thereby inducing the electrons and the holes to participate in the photo reduction and oxidation processes, respectively and enhancing the photocatalytic activity. Copyright © 2016 Elsevier Ltd. All rights reserved.

Photodegradation of Methylene Blue by TiO2-Fe3O4-Bentonite Magnetic Nanocomposite

Directory of Open Access Journals (Sweden)

Wei Chen

2015-01-01

Full Text Available Fe3O4-bentonite nanoparticles have been prepared by a coprecipitation technique under a nitrogen atmosphere. An aqueous suspension of bentonite was first modified with FeCl2 and FeCl3. TiO2 was then loaded onto the surface of the Fe3O4-bentonite by a sol-gel method. After sufficient drying, the colloidal solution was placed in a muffle furnace at 773 K to obtain the TiO2-Fe3O4-bentonite composite. The material has been characterized by scanning electron microscopy (SEM, X-ray diffraction (XRD analysis, and vibrating sample magnetometry (VSM. Morphological observation showed that Fe3O4 and TiO2 nanoparticles had been adsorbed on the surface of bentonite nanoneedles. The material was then applied for the photodegradation of the azo dye methylene blue (MB. It was found that the removal efficiency of MB exceeded 90% under UV illumination, and that only a 20% mass loss was incurred after six cycles. The composite material thus showed good photocatalytic performance and recycling properties.

A sensitive resveratrol assay with a simple probe methylene blue by resonance light scattering technique

Science.gov (United States)

Xiang, Haiyan; Dai, Kaijin; Luo, Qizhi; Duan, Wenjun; Xie, Yang

2011-01-01

A novel resonance light scattering (RLS) method was developed for the determination of resveratrol based on the interaction between resveratrol and methylene blue (MB). It was found that at pH 8.69, the weak RLS intensity of MB was remarkably enhanced by the addition of trace amount of resveratrol with the maximum peak located at 385.0 nm. Under the optimum conditions, a good linear relationship between the enhanced RLS intensities and the concentrations of resveratrol was obtained over the range of 2.0-14.0 μg ml -1 with the detection limit (3 σ) of 0.63 μg ml -1. The results of the analysis of resveratrol in synthetic samples and human urine are satisfactory, which showed it may provide a more sensitive, convenient, rapid and reproducible method for the detection of resveratrol, especially in biological and pharmaceutical field. In this work, the characteristics of RLS, absorption and fluorescence spectra of the resveratrol-MB system, the influencing factors and the optimum conditions of the reaction were investigated.

Kinetics, Equilibrium, and Thermodynamic Studies on Adsorption of Methylene Blue by Carbonized Plant Leaf Powder

Directory of Open Access Journals (Sweden)

V. Gunasekar

2013-01-01

Full Text Available Carbon synthesized from plant leaf powder was employed for the adsorption of methylene blue from aqueous effluent. Effects of pH (2, 4, 6, 8, and 9, dye concentration (50, 100, 150, and 200 mg/dm3, adsorbent dosage (0.5, 1.0, 1.5, and 2.0 g/dm3, and temperature (303, 313, and 323 K were studied. The process followed pseudo-second-order kinetics. Equilibrium data was examined with Langmuir and Freundlich isotherm models and Langmuir model was found to be the best fitting model with high R2 and low chi2 values. Langmuir monolayer adsorption capacity of the adsorbent was found to be 61.22 mg/g. From the thermodynamic analysis, ΔH, ΔG, and ΔS values for the adsorption of MB onto the plant leaf carbon were found out. From the values of free energy change, the process was found out to be feasible process. From the magnitude of ΔH, the process was found to be endothermic physisorption.

Menace of childhood non-accidental traumatic brain injuries: A single unit report

Directory of Open Access Journals (Sweden)

Musa Ibrahim

2015-01-01

Full Text Available Background: Childhood traumatic brain injury (TBI has high rate of mortality and morbidity worldwide. There are dearths of reports from developing countries with large paediatric population on trauma; neurosurgery trauma of nonaccidental origin is not an exemption. This study analysed menace of non-accidental TBI in the paediatric population from our center. Materials and Methods: This is a single unit, retrospective study of the epidemiology of non-accidental TBI in children starting from September, 2008 to March, 2014. The management outcomes of the epidemiology of the non-accidental TBI were analysed. Results: Total of 109 children age range from 0 (intra-natal to 16 years with a mean of 5.8 ± 4.6 years (median, 5 years were enrolled into the study. 34 (31.2% were domestic violence, 26 (23.9% street assaults, 16 (14.7% were due to animal assaults and mishaps, 17 (15.6% fall from heights. Seven (6.4% cases of collapsed buildings were also seen during the period. Four (3.7% industrial accidents and two (1.8% were self-inflicted injuries. There were also three (2.8% cases of iatrogenic TBI out of which two infants (1.8% sustained TBI from cesarean section procedure while one patient (0.9% under general anaesthesia felt from the operation bed resulting to severe TBI. Conclusion: Child abuse, unprotected child labour, parental/care-givers negligence are the main cause of nonaccidental TBI. Human right activists and government agents should be incorporated in curtailing the menace.

Removal of Congo Red and Methylene Blue from Aqueous Solutions by Vermicompost-Derived Biochars

Science.gov (United States)

Yang, Gang; Wu, Lin; Xian, Qiming; Shen, Fei; Wu, Jun; Zhang, Yanzong

2016-01-01

Biochars, produced by pyrolyzing vermicompost at 300, 500, and 700°C were characterized and their ability to adsorb the dyes Congo red (CR) and Methylene blue (MB) in an aqueous solution was investigated. The physical and chemical properties of biochars varied significantly based on the pyrolysis temperatures. Analysis of the data revealed that the aromaticity, polarity, specific surface area, pH, and ash content of the biochars increased gradually with the increase in pyrolysis temperature, while the cation exchange capacity, and carbon, hydrogen, nitrogen and oxygen contents decreased. The adsorption kinetics of CR and MB were described by pseudo-second-order kinetic models. Both of Langmuir and Temkin model could be employed to describe the adsorption behaviors of CR and MB by these biochars. The biochars generated at higher pyrolysis temperature displayed higher CR adsorption capacities and lower MB adsorption capacities than those compared with the biochars generated at lower pyrolysis temperatures. The biochar generated at the higher pyrolytic temperature displayed the higher ability to adsorb CR owing to its promoted aromaticity, and the cation exchange is the key factor that positively affects adsorption of MB. PMID:27144922

High surface area mesoporous activated carbon-alginate beads for efficient removal of methylene blue.

Science.gov (United States)

Nasrullah, Asma; Bhat, A H; Naeem, Abdul; Isa, Mohamed Hasnain; Danish, Mohammed

2018-02-01

High surface area mesoporous activated carbon-alginate (AC-alginate) beads were successfully synthesized by entrapping activated carbon powder derived from Mangosteen fruit peel into calcium-alginate beads for methylene blue (MB) removal from aqueous solution. The structure and surface characteristics of AC-alginate beads were analyzed using Fourier transform infra-red (FTIR) spectroscopy, scanning electron microscopy (SEM) and surface area analysis (S BET ), while thermal properties were tested using thermogravimetric analysis (TGA). The effect of AC-alginate dose, pH of solution, contact time, initial concentration of MB solution and temperature on MB removal was elucidated. The results showed that the maximum adsorption capacity of 230mg/g was achieved for 100mg/L of MB solution at pH 9.5 and temperature 25°C. Furthermore, the adsorption of MB on AC-alginate beads followed well pseudo-second order equation and equilibrium adsorption data were better fitted by the Freundlich isotherm model. The findings reveal the feasibility of AC-alginate beads composite to be used as a potential and low cost adsorbent for removal of cationic dyes. Copyright © 2017 Elsevier B.V. All rights reserved.

High-pressure homogenization associated hydrothermal process of palygorskite for enhanced adsorption of Methylene blue

Science.gov (United States)

Zhang, Zhifang; Wang, Wenbo; Wang, Aiqin

2015-02-01

Palygorskite (PAL) was modified by a high-pressure homogenization assisted hydrothermal process. The effects of modification on the morphology, structure and physicochemical properties of PAL were systematically investigated by Field-emission scanning electron microscopy (FESEM), Transmission electron microscopy (TEM), Fourier transform infrared spectrometry (FTIR), Brunauer-Emmett-Teller (BET) analysis, X-ray diffraction (XRD) and Zeta potential analysis techniques, and the adsorption properties were systematically evaluated using Methylene blue (MB) as the model dye. The results revealed that the crystal bundles were disaggregated and the PAL nanorods became more even after treated via associated high-pressure homogenization and hydrothermal process, and the crystal bundles were dispersed as nanorods. The intrinsic crystal structure of PAL was remained after hydrothermal treatment, and the pore size calculated by the BET method was increased. The adsorption properties of PAL for MB were evidently improved (from 119 mg/g to 171 mg/g) after modification, and the dispersion of PAL before hydrothermal reaction is favorable to the adsorption. The desorption evaluation confirms that the modified PAL has stronger affinity with MB, which is benefit to fabricate a stable organic-inorganic hybrid pigment.

Deconvolution analysis of sup(99m)Tc-methylene diphosphonate kinetics in metabolic bone disease

International Nuclear Information System (INIS)

Knop, J.; Kroeger, E.; Stritzke, P.; Schneider, C.; Kruse, H.P.; Hamburg Univ.

1981-01-01

The kinetics of sup(99m)Tc-methylene diphosphonate (MDP) and 47 Ca were studied in three patients with osteoporosis, three patients with hyperparathyroidism, and two patients with osteomalacia. The activities of sup(99m)Tc-MDP were recorded in the lumbar spine, paravertebral soft tissues, and in venous blood samples for 1 h after injection. The results were submitted to deconvolution analysis to determine regional bone accumulation rates. 47 Ca kinetics were analysed by a linear two-compartment model quantitating short-term mineral exchange, exchangeable bone calcium, and calcium accretion. The sup(99m)Tc-MDP accumulation rates were small in osteoporosis, greater in hyperparathyroidism, and greatest in osteomalacia. No correlations were obtained between sup(99m)Tc-MDP bone accumulation rates and the results of 47 Ca kinetics. However, there was a significant relationship between the level of serum alkaline phosphatase and bone accumulation rates (R = 0.71, P 47 Ca kinetics might suggest a preferential binding of sup(99m)Tc-MDP to the organic matrix of the bone, as has been suggested by other authors on the basis of experimental and clinical investigations. (orig.)

Facile Synthesis of Uniform Zinc-blende ZnS Nanospheres with Excellent Photocatalytic Activity toward Methylene Blue Degradation

Institute of Scientific and Technical Information of China (English)

PENG Si-Yan; YANG Liu-Sai; LV Ying-Ying; YU Le-Shu; HUANG Hai-Jin; WU Li-Dan

2017-01-01

Uniform and well-dispersed ZnS nanospheres have been successfully synthesized via a facile chemical route.The crystal structure,morphology,surface area and photocatalytic properties of the sample were characterized by powder X-ray diffraction (XRD),scanning electron microscopy (SEM),Brunauer-Emmett-Teller (BET) and ultraviolet-visible (UV-vis) spectrum.The results of characterizations indicate that the products are identified as mesoporous zinc-blende ZnS nanospheres with an average diameter of 200 nm,which are comprised of nanoparticles with the crystallite size of about 3.2 nm calculated by XRD.Very importantly,photocatalytic degradation of methylene blue (MB)shows that the as-prepared ZnS nanospheres exhibit excellent photocatalytic activity with nearly 100％ of MB decomposed after UV-light irradiation for 25 min.The excellent photocatalytic activity of ZnS nanospheres can be ascribed to the large specific surface area and hierarchical mesoporous structure.

Interface-enhanced high-temperature superconductivity in single-unit-cell FeT e1 -xS ex films on SrTi O3

Science.gov (United States)

Li, Fangsen; Ding, Hao; Tang, Chenjia; Peng, Junping; Zhang, Qinghua; Zhang, Wenhao; Zhou, Guanyu; Zhang, Ding; Song, Can-Li; He, Ke; Ji, Shuaihua; Chen, Xi; Gu, Lin; Wang, Lili; Ma, Xu-Cun; Xue, Qi-Kun

2015-06-01

Recently discovered high-temperature superconductivity in single-unit-cell (UC) FeSe films on SrTi O3 (STO) substrate has stimulated tremendous research interest, both experimental and theoretical. Whether this scenario could be extended to other superconductors is vital in both identifying the enhanced superconductivity mechanism and further raising the critical transition temperature (Tc). Here we successfully prepared single-UC FeT e1 -xS ex(0.1 ≤x ≤0.6 ) films on STO substrates by molecular beam epitaxy and observed U -shaped superconducting gaps (Δ ) up to ˜16.5 meV , nearly ten times the gap value (Δ ˜1.7 meV ) of the optimally doped bulk FeT e0 .6S e0 .4 single crystal (Tc˜14.5 K ). No superconducting gap has been observed on the second UC and thicker FeT e1 -xS ex films at 5.7 K, indicating the important role of the interface. This interface-enhanced high-temperature superconductivity is further confirmed by ex situ transport measurements, which revealed an onset superconducting transition temperature above 40 K, nearly two times higher than that of the optimally doped bulk FeT e0 .6S e0 .4 single crystal. This work demonstrates that interface engineering is a feasible way to discover alternative superconductors with higher Tc.

The photocatalytic degradation of methylene blue by green semiconductor films that is induced by irradiation by a light-emitting diode and visible light.

Science.gov (United States)

Yang, Chih-Chi; Doong, Ruey-An; Chen, Ku-Fan; Chen, Giin-Shan; Tsai, Yung-Pin

2018-01-01

This study develops a low-energy rotating photocatalytic contactor (LE-RPC) that has Cu-doped TiO 2 films coated on stainless-steel rotating disks, to experimentally evaluate the efficiency of the degradation and decolorization of methylene blue (MB) under irradiation from different light sources (visible 430 nm, light-emitting diode [LED] 460 nm, and LED 525 nm). The production of hydroxyl radicals is also examined. The experimental results show that the photocatalytic activity of TiO 2 that is doped with Cu 2+ is induced by illumination with visible light and an LED. More than 90% of methylene blue at a 10 mg/L concentration is degraded after illumination by visible light (430 nm) for 4 hr at 20 rpm. This study also demonstrates that the quantity of hydroxyl radicals produced is directly proportional to the light energy intensity. The greater the light energy intensity, the greater is the number of hydroxyl radicals produced. The CuO-doped anatase TiO 2 powder was successfully synthesized in this study by a sol-gel method. The catalytic abilities of the stainless-steel film were enhanced in the visible light regions. This study has successfully modified the nano-photocatalytic materials to drop band gap and has also successfully fixed the nano-photocatalytic materials on a substratum to effectively treat dye wastewater in the range of visible light. The results can be useful to the development of a low-energy rotating photocatalytic contactor for decontamination purposes.

Cultural and morphological properties of the vaccine strain Yersinia pestis EV NIIEG bacteria after photodynamic inactivation

Science.gov (United States)

Ulianova, Onega V.; Lyapina, Anna M.; Khizhnyakova, Mariya A.; Laskavy, Vladislav N.; Feodorova, Valentina A.; Ulyanov, Sergey S.

2015-03-01

New method of photoinactivation of plague microbes (bacteria Yersinia pestis) has been suggested. Rate of growth of colonies of Y. pestis EV NIIEG at specific regimes of photo processing have been analyzed. Dependence of growth on exposure time and concentrations of photosensitizer (methylene blue) has been studied. Number of colony forming units of Y. pestis EV NIIEG bacteria as a function of intensity of light and concentration of methylene blue has been scrutinized.

Nanoscale zero-valent iron incorporated with nanomagnetic diatomite for catalytic degradation of methylene blue in heterogeneous Fenton system.

Science.gov (United States)

Zha, Yiming; Zhou, Ziqing; He, Haibo; Wang, Tianlin; Luo, Liqiang

2016-01-01

Nanoscale zero-valent iron (nZVI) incorporated with nanomagnetic diatomite (DE) composite material was prepared for catalytic degradation of methylene blue (MB) in heterogeneous Fenton system. The material was constructed by two facile steps: Fe3O4 magnetic nanoparticles were supported on DE by chemical co-precipitation method, after which nZVI was incorporated into magnetic DE by liquid-phase chemical reduction strategy. The as-prepared catalyst was characterized by scanning electron microscopy, Fourier-transform infrared spectroscopy, X-ray diffraction, magnetic properties measurement and nitrogen adsorption-desorption isotherm measurement. The novel nZVI@Fe3O4-diatomite nanocomposites showed a distinct catalytic activity and a desirable effect for degradation of MB. MB could be completely decolorized within 8 min and the removal efficiency of total organic carbon could reach to 90% after reaction for 1 h.

Degree of conversion of resin-based materials cured with dual-peak or single-peak LED light-curing units.

Science.gov (United States)

Lucey, Siobhan M; Santini, Ario; Roebuck, Elizabeth M

2015-03-01

There is a lack of data on polymerization of resin-based materials (RBMs) used in paediatric dentistry, using dual-peak light-emitting diode (LED) light-curing units (LCUs). To evaluate the degree of conversion (DC) of RBMs cured with dual-peak or single-peak LED LCUs. Samples of Vit-l-escence (Ultradent) and Herculite XRV Ultra (Kerr) and fissure sealants Delton Clear and Delton Opaque (Dentsply) were prepared (n = 3 per group) and cured with either one of two dual-peak LCUs (bluephase(®) G2; Ivoclar Vivadent or Valo; Ultradent) or a single-peak (bluephase(®) ; Ivoclar Vivadent). High-performance liquid chromatography and nuclear magnetic resonance spectroscopy were used to confirm the presence or absence of initiators other than camphorquinone. The DC was determined using micro-Raman spectroscopy. Data were analysed using general linear model anova; α = 0.05. With Herculite XRV Ultra, the single-peak LCU gave higher DC values than either of the two dual-peak LCUs (P < 0.05). Both fissure sealants showed higher DC compared with the two RBMs (P < 0.05); the DC at the bottom of the clear sealant was greater than the opaque sealant, (P < 0.05). 2,4,6-trimethylbenzoyldiphenylphosphine oxide (Lucirin(®) TPO) was found only in Vit-l-escence. Dual-peak LED LCUs may not be best suited for curing non-Lucirin(®) TPO-containing materials. A clear sealant showed a better cure throughout the material and may be more appropriate than opaque versions in deep fissures. © 2014 BSPD, IAPD and John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Extraction of uranium(6), transuranium elements and europium by bidentate neutral phosphorus- and phosphorus-nitrogen-containing reagents with substituent in methylene bridge

International Nuclear Information System (INIS)

Kochetkova, N.E.; Kojro, O.Eh.; Nesterova, N.P.; Medved', T.Ya.; Chmutova, M.K.; Myasoedov, B.F.; Kabachnik, M.I.

1986-01-01

The influence of substituents in methylene bridge on solubility, extractivity and selectivity of bidentate neutral phosphorus- and phosphorus-nitrogen-containing reagents in the process of U(6), TUE, Eu extraction has been studied. It is ascertained that hydrogen substitution in the bridge of tetraphenylmethylenediphosphine dioxide (1) causes a decrease in the extractivity of reagent as to TPE, uranium (6) and europium. There is no visible regular relation between basicity and extractivity of substituted reagents. Hydrogen substitution in the bridge of diphenyl[diethylcarbamoylmethyl]phosphine oxide (2) causes a decrease in extractivity of the reagent as to TPE, uranium (6) and europium. In contrast to monodentate neutral reagents, when bidentate neutral reagents are used, sometimes no increase in the reagent extractivity with an increase in its basicity is observed. When fragments restricting the conformation mobility of bidentate reagent molecule are introduced in it (here substituents in methylene bridge), it may result in the violation of the regularity, since of all the factors affecting the reagent extractivity the spatial factor may become the prevailing one. On hydrogen substitution in the bridge of 1 separation factors of practically all (with few exceptions) studied pairs of elements increase. Hydrogen substitution in the bridge of 2 causes an increase in separation factor of U (6) /Am pair and it does not affect the separation factor of Am/Eu pair. Hydrogen substitution in the bridge of 1 and 2 does not result in the preparation of more efficient and considerably more selective reagents for extractive isolation and separation of the elements, but some of the substituted reagents (Cl-substituted 1, for instance) may turn out useful for the element separation

Coupling Fe{sup 0} nano particles with living and dead Azolla filicoloides to improve removal of methylene blue from aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Rakhshaee, Roohan, E-mail: roohan_rakhshaee@guilan.ac.ir

2015-11-30

Highlights: • The novel living and dead bio–nano couples were prepared. • Living Azolla was more effective stabilizer for nano particles. • Increasing stabilization increased methylene blue (MB) adsorption. • The portion of Fe{sup 0} NPs had the main rule to determine kinetic model to adsorb MB. • It was studied the various factors rule on the living Azolla growth and MB removal. - Abstract: Fe{sup 0} nano particles (FNPs) were connected to the cell wall of the dead and living Azolla filicoloides as an aquatic fern, individually. FNPs mean size was decreased due to the stabilization, especially using the living one. It was compared the results of X-ray photoelectron spectroscopy (XPS), saturation magnetization (Ms), zeta potential (ZP) and thermal analysis (DSC and TGA) of the dead and living Azolla connected to FNPs, and also the findings of potentiometric titration (PT) of the cell wall's pectin of the dead and living Azolla. It was confirmed (by XRD and XPS) that Fe{sup 0} nano particles when were connected to the living Azolla did not produce Fe{sub 3}O{sub 4} due to oxidation unlike the bare FNPs and the connected form to the dead Azolla, by reason of the more stabilization (more surface protection) of nano iron particles after connecting to the living Azolla. To adsorb methylene blue by these agents at the optimum pre-treatment pH 10 and adsorption pH 8, the parameters of equilibrium sorption, rate constant of second-order sorption and activation energy were obtained as: living Azolla–FNPs > dead Azolla–FNPs > FNPs > dead Azolla, while, their thermodynamic parameters (ΔG°, ΔH° and ΔS°) had the reverse arrangement. It was also studied the various factors rule such as photoperiod and the presence of heavy metals on the living Azolla growth coupled with FNPs and its MB removal ability.

Valorization of two waste streams into activated carbon and studying its adsorption kinetics, equilibrium isotherms and thermodynamics for methylene blue removal

Directory of Open Access Journals (Sweden)

Zeid Abdullah AlOthman

2014-12-01

Full Text Available Wastes must be managed properly to avoid negative impacts that may result. Open burning of waste causes air pollution which is particularly hazardous. Flies, mosquitoes and rats are major problems in poorly managed surroundings. Uncollected wastes often cause unsanitary conditions and hinder the efforts to keep streets and open spaces in a clean and attractive condition. During final disposal methane is generated, it is much more effective than carbon dioxide as a greenhouse gas, leading to climate change. Therefore, this study describes the possible valorization of two waste streams into activated carbon (AC with added value due to copyrolysis. High efficiency activated carbon was prepared by the copyrolysis of palm stem waste and lubricating oil waste. The effects of the lubricating oil waste to palm stem ratio and the carbonization temperature on the yield and adsorption capacity of the activated carbon were investigated. The results indicated that the carbon yield depended strongly on both the carbonization temperature and the lubricating oil to palm stem ratio. The efficiency of the adsorption of methylene blue (MB onto the prepared carbons increased when the lubricating oil to palm stem ratio increased due to synergistic effect. The effects of pH, contact time, and the initial adsorbate concentration on the adsorption of methylene blue were investigated. The maximum adsorption capacity (128.89 mg/g of MB occurred at pH 8.0. The MB adsorption kinetics were analyzed using pseudo-first order, pseudo-second order and intraparticle diffusion kinetic models. The results indicated that the adsorption of MB onto activated carbon is best described using a second order kinetic model. Adsorption data are well fitted with Langmuir and Freundlich isotherms. The thermodynamic parameters; ΔG°, ΔH° and ΔS° indicate that the adsorption is spontaneous and endothermic.

Complexation between carrageenan and methylene blue for sensor design

Science.gov (United States)

Ling, Yew Pei; Heng, Lee Yook

2013-11-01

Theoretical studies on the methylene blue (MB)-carrageenans complexation at solution and solid states have been carried out via ultraviolet spectrophotoscopy and reflectometry methods. The equilibrium constant (Ka) of the MBcarrageenans complexation follows the order of Iota > Lambda > Kappa carrageenans, which indicated Iota-carrageenan forms a stable complex. MB-carrageenan complexation reaction showed decrease in Ka value from 210.71 ppm-1 to 114.57 ppm-1 when the reaction temperature increased from 298 K to 323 K. Le Chatelier's principle and mass action law explained that the MB-carrageenan complexation was an exothermic reaction (ΔH=-18.54 kJmol-1) that release heat. Thus MB-carrageenan complex was less stable at high temperature and tend to dissociate into free MB and carrageenan molecules. It was also supported by the van't Hoff equation. The reaction is a spontaneous process (ΔG=-13.23 kJmol-1) where the randomness of the molecules reduced (ΔS=-17.83 Jmol-1K-1) due to complexation. Besides, linear regression of the concentration and absorption of the MB-carrageenan reaction obeys the Beer Lambert law, which elucidated that the complexation process was not affected by any concentration dependent factors such as aggregation and self-quenching. Moreover, linear Benesi Hilderbrend plot revealed that the interaction between MB and carrageenan was a reversible and stoichiometric reaction with 1:1 ratio. However, the molar extinction coefficient (ɛ) and molar adsorption coefficient (μa) of the MB-carrageenan complex were lower compared to free MB, described that the complex was less adsorptive. The sensor constructed based on these theoretical investigations showed response behavior that was similar with solution test as both have attraction for carrageenans in the sequence of Iota-, Lambda-, Kappa- carrageenans. Likewise, carrageenan sensor was more selective towards Iota-carrageenan than to Lambda- and Kappa-carrageenans, and no response observed when

Reactive oxygen species generation in aqueous solutions containing GdVO4:Eu3+ nanoparticles and their complexes with methylene blue

Science.gov (United States)

Hubenko, Kateryna; Yefimova, Svetlana; Tkacheva, Tatyana; Maksimchuk, Pavel; Borovoy, Igor; Klochkov, Vladimir; Kavok, Nataliya; Opolonin, Oleksander; Malyukin, Yuri

2018-04-01

It this letter, we report the study of free radicals and reactive oxygen species (ROS) generation in water solutions containing gadolinium orthovanadate GdVO4:Eu3+ nanoparticles (VNPs) and their complexes with methylene blue (MB) photosensitizer. The catalytic activity was studied under UV-Vis and X-ray irradiation by three methods (conjugated dienes test, OH· radical, and singlet oxygen detection). It has been shown that the VNPs-MB complexes reveal high efficiency of ROS generation under UV-Vis irradiation associated with both high efficiency of OH· radicals generation by VNPs and singlet oxygen generation by MB due to nonradiative excitation energy transfer from VNPs to MB molecules. Contrary to that under X-ray irradiation, the strong OH . radicals scavenging by VNPs has been observed.

Single Cigarette Sales: State Differences in FDA Advertising and Labeling Violations, 2014, United States.

Science.gov (United States)

Baker, Hannah M; Lee, Joseph G L; Ranney, Leah M; Goldstein, Adam O

2016-02-01

Single cigarettes, which are sold without warning labels and often evade taxes, can serve as a gateway for youth smoking. The Family Smoking Prevention and Tobacco Control Act of 2009 gives the US Food and Drug Administration (FDA) authority to regulate the manufacture, distribution, and marketing of tobacco products, including prohibiting the sale of single cigarettes. To enforce these regulations, the FDA conducted over 335,661 inspections between 2010 and September 30, 2014, and allocated over $115 million toward state inspections contracts. To examine differences in single cigarette violations across states and determine if likely correlates of single cigarette sales predict single cigarette violations at the state level. Cross-sectional study of publicly available FDA warning letters from January 1 to July 31, 2014. All 50 states and the District of Columbia. Tobacco retailer inspections conducted by FDA (n = 33 543). State cigarette tax, youth smoking prevalence, poverty, and tobacco production. State proportion of FDA warning letters issued for single cigarette violations. There are striking differences in the number of single cigarette violations found by state, with 38 states producing no warning letters for selling single cigarettes even as state policymakers developed legislation to address retailer sales of single cigarettes. The state proportion of warning letters issued for single cigarettes is not predicted by state cigarette tax, youth smoking, poverty, or tobacco production, P = .12. Substantial, unexplained variation exists in violations of single cigarette sales among states. These data suggest the possibility of differences in implementation of FDA inspections and the need for stronger quality monitoring processes across states implementing FDA inspections. © The Author 2015. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Modifikasi Limbah Tulang Sapi Bali dan Pemanfaatannya untuk Adsorpsi Methylene Blue (MODIFICATION OF BALI COW BONE WASTE AND ITS APPLICATION TO ADSORPTION OF METHYLENE BLUE

Directory of Open Access Journals (Sweden)

I Nengah Simpen

2017-01-01

Full Text Available The research of modification, characterization, and application of nano-porous adsorbent base onBali cow bone waste to methylene blue (MB adsorption has been carried out. The modification was carriedout through extraction of hydroxyapatite (HA from cow bone, then its activated by 0.4 M NaOH solutionand coating to form active sites of Fe and Fe-Al oxides. The adsorbent was applied to know quantitativelyadsorption capacity coated-HA (CHA to MB as wastewaters simulation. Compound of CHA wascharacterized amount of active sites by base-acid titration, Bronsted-Lewis acid sites by FTIR spectroscopy,specific surface area by MB method and pore size by surface area analyzer gasorption nitrogen. While,amount of coated-Fe and Al by LIBS. Amount of MB adsorbed was analyzed by UV-Vis spectrophotometer.The results showed that coating of Fe and Fe-Al oxides increased amount of active sites, sites distributionof new Lewis acid site, everage nano pore size with pore volume is microporous (less than 2 nm, and Fe andFe-Al oxides was into HA crystal structure. The amount of active sites was the higest of T1-Fe-Al2O3 andall pores diameter less than 58.182 nm.While, the specific surface area increased T3-Fe2O3>T3-Fe-Al2O3>T2-Fe2O3 respectively. In the adsorption isotherm, coating on HA significantly increased ability of adsorbentand through Freundlich model (R2 > 0.77 with the higest adsorption capacity on T3-Fe2O3 (3.2019 mg/gthen T2-Fe-Al2O3 (2.7921 mg/g. Results of this research indicate that Fe and Fe-Al oxides HA-modifiedincreased adsorption ability.

Twenty years of vasoplegic syndrome treatment in heart surgery. Methylene blue revised

Directory of Open Access Journals (Sweden)

Paulo Roberto Barbosa Evora

2015-02-01

Full Text Available Objective: This study was conducted to reassess the concepts established over the past 20 years, in particular in the last 5 years, about the use of methylene blue in the treatment of vasoplegic syndrome in cardiac surgery. Methods: A wide literature review was carried out using the data extracted from: MEDLINE, SCOPUS and ISI WEB OF SCIENCE. Results: The reassessed and reaffirmed concepts were 1 MB is safe in the recommended doses (the lethal dose is 40 mg/kg; 2 MB does not cause endothelial dysfunction; 3 The MB effect appears in cases of NO up-regulation; 4 MB is not a vasoconstrictor, by blocking the cGMP pathway it releases the cAMP pathway, facilitating the norepinephrine vasoconstrictor effect; 5 The most used dosage is 2 mg/kg as IV bolus, followed by the same continuous infusion because plasma concentrations sharply decrease in the first 40 minutes; and 6 There is a possible "window of opportunity" for MB's effectiveness. In the last five years, major challenges were: 1 Observations about side effects; 2 The need for prophylactic and therapeutic guidelines, and; 3 The need for the establishment of the MB therapeutic window in humans. Conclusion: MB action to treat vasoplegic syndrome is time-dependent. Therefore, the great challenge is the need, for the establishment the MB therapeutic window in humans. This would be the first step towards a systematic guideline to be followed by possible multicenter studies.

Methylene blue biosorption by pericarp of corn, alfalfa, and agave bagasse wastes.

Science.gov (United States)

Rosas-Castor, José M; Garza-González, María T; García-Reyes, Refugio B; Soto-Regalado, Eduardo; Cerino-Córdova, Felipe J; García-González, Alcione; Loredo-Medrano, José A

2014-01-01

The presence of dyes in effluent is a matter of concern due to their toxicologic and aesthetical effects. In this research, locally available agro-industrial wastes (Zea mays pericarp, ZMP; Agave tequilana bagasse, ATB; and Medicago sativa waste, MSW) were used as alternative low-cost adsorbents for the removal of methylene blue (MB) from aqueous solutions. The adsorbents were characterized physically and chemically by Fourier transform infrared, scanning electron microscopy, potentiometric titrations, and N2 physisorption. MB adsorption experiments were carried out in batch systems and experimental data were used to calculate the adsorption isotherm model parameters (Langmuir, Freundlich, and Temkin) and the adsorption kinetic model parameters (pseudo-first- and pseudo-second-order models). MB-loaded biosorbents were desorbed with deionized water, ethanol (10% and 50% v/v), hydrochloric acid (0.01 and 0.05 N), and sodium hydroxide (0.1 N) at room temperature, and the best eluent was used in various adsorption-desorption cycles. The selected agricultural wastes can be considered as promising adsorbents for dye uptake from water since they exhibit considerable MB adsorption capacity (MSW 202.6 mg g(-1), ATB 156.2mg g(-1), and ZMP 110.9mg g(-1)), but it is lower than that reported for activated carbon; however, the biosorbents show higher adsorption rate than powdered activated carbon. Furthermore, the adsorbents can be economically regenerated with HCl solutions and reused for seven adsorption-desorption cycles.

Solid-phase microextraction of Methylene Blue using carboxy graphene-modified steel wires, and its detection by electrochemiluminescence

International Nuclear Information System (INIS)

Wang, Sui; Lv, Shasha; Guo, Zhiyong; Jiang, Feng

2014-01-01

We report on a new solid phase for microextraction (SPME) of Methylene Blue (MB). It was obtained by immobilizing carboxy graphene (G-COOH) on a stainless steel wire. Scanning electron micrography showed the surface to be homogeneous, porous and wrinkled. The effects of sample solution pH, extraction time, stirring rate, desorption time and of desorption solvent on the efficiency of extraction of MB were optimized. The new SPME was coupled to electrochemiluminescence detection of MB and gave a linear analytical range from 2.7 nM to 1.3 μM, and the detection limit is 0.89 nM which is better than other methods. When considering the enrichment factor of ∼20, the resulting detection limit is estimated to be 45 pM. The new SPME fiber was successfully applied to the analysis of MB in spiked real water samples. Recoveries range from 95.7 % to 113.0 %, and relative standard deviations are <5.0 %, which showed the good reproducibility of the method. (author)

Multiwalled carbon nanotubes/silver nanocomposite as effective SERS platform for detection of methylene blue dye in water

Directory of Open Access Journals (Sweden)

Ngo Xuan Dinh

2016-03-01

Full Text Available In this work, a functional nanocomposite consisting of silver nanoparticles and multiwalled carbon nanotubes (MWCNTs-Ag was successfully synthesized using a two-step chemical process. The MWCNTs-Ag nanocomposite has been studied as a surface-enhanced Raman scattering (SERS sensing platform for detection of methylene blue (MB dye in an aqueous medium. The obtained results reveal that the MWCNTs-Ag nanocomposite exhibits higher SERS detection activity than that of pure Ag-nanoparticles (Ag-NPs. The calculated enhancement factors are 1.51 × 106 for pure Ag-NPs and 4.68 × 106 for the MWCNTs-Ag nanocomposite. MB detection has been achieved as low as 1 ppm. The SERS enhancement of the MWCNTs-Ag nanocomposite can be attributed to the combination of both an electromagnetic (EM effect and a chemical effect (CE. With exhibited properties, the MWCNTs-Ag nanocomposite can be effectively used for detection of various organic dyes in water solution.

Application of carbon-coated TiO2 for decomposition of methylene blue in a photocatalytic membrane reactor

International Nuclear Information System (INIS)

Mozia, Sylwia; Toyoda, Masahiro; Inagaki, Michio; Tryba, Beata; Morawski, Antoni W.

2007-01-01

An application of carbon-coated TiO 2 for decomposition of methylene blue (MB) in a photocatalytic membrane reactor (PMR), coupling photocatalysis and direct contact membrane distillation (DCMD) was investigated. Moreover, photodegradation of a model pollutant in a batch reactor without membrane distillation (MD) was also examined. Carbon-modified TiO 2 catalysts containing different amount of carbon and commercially available TiO 2 (ST-01) were used in this study. The carbon-coated catalyst prepared from a mixture of ST-01 and polyvinyl alcohol in the mass ratio of 70/30 was the most effective in degradation of MB from all of the photocatalysts applied. Photodecomposition of MB on the recovered photocatalysts was lower than on the fresh ones. The photodegradation of MB in the PMR was slower than in the batch reactor, what probably resulted from shorter time of exposure of the catalyst particles to UV irradiation. The MD process could be successfully applied for separation of photocatalyst and by-products from the feed solution

Increased Water Solubility of the Curcumin Derivatives via Substitution with an Acetoxy Group at the Central Methylene Moiety

Energy Technology Data Exchange (ETDEWEB)

Kim, Mi Kyoung; Mok, Hyejung; Chong, Youhoon [Konkuk Univ., Seoul (Korea, Republic of)

2012-09-15

Curcumin (diferuloyl methane), a natural yellow pigment in the roots of turmeric, has been considered as one of the most promising chemopreventive agents against a variety of human cancers. Curcumin is known to exhibit its antiproliferative effect against various cancer cells through cell cycle arrest and induction of apoptosis. Although not as potent as many other cytotoxic agents, curcumin has been demonstrated to be safe in humans at relatively high doses (10 grams/day), making it an attractive target for chemotherapeutic drug discovery efforts. Two compounds with meta-methoxy substituents (2 and 3) maintained comparable antiproliferative activity with curcumin (1). In contrast, the acetoxy-curcuminoids (8-14) showed moderate to potent activity against all three cancer cell lines tested (Table 1). In particular, the colon cancer cell (HCT116) was most susceptible to the acetoxy-curcuminoids (8-12, Table 1) to show 2-2.5 times increase in EC{sub 50} values compared with that of curcumin (1, Table 1). In this series, like the simple curcuminoids (2-7), the aromatic meta-methoxy substituent turned out to be critical for the antiproliferative effect, and the corresponding acetoxy-curcuminoids 10 and 11 showed the most potent activity against HCT116 with EC{sub 50} values of 18.5 μM and 16.9 μM, respectively. Also noteworthy is the broad spectrum antiproliferative effect of the acetoxy-curcuminoid 11 with a free catechol moiety, which exhibited almost similar antiproliferative activity against all three cancer cell lines tested. Taken together, through evaluation of solubility as well as antiproliferative effect of the acetoxy-curcuminoids, we figured out that the acetoxy group substituted at the central methylene unit which served to enhance the solubility of the corresponding curcuminoids also played a key role in potentiating their antiproliferative effect. Thus, upon combination of the methylenyl acetoxy group and the aromatic meta-methoxy group on the curcumin

Increased Water Solubility of the Curcumin Derivatives via Substitution with an Acetoxy Group at the Central Methylene Moiety

International Nuclear Information System (INIS)

Kim, Mi Kyoung; Mok, Hyejung; Chong, Youhoon

2012-01-01

Curcumin (diferuloyl methane), a natural yellow pigment in the roots of turmeric, has been considered as one of the most promising chemopreventive agents against a variety of human cancers. Curcumin is known to exhibit its antiproliferative effect against various cancer cells through cell cycle arrest and induction of apoptosis. Although not as potent as many other cytotoxic agents, curcumin has been demonstrated to be safe in humans at relatively high doses (10 grams/day), making it an attractive target for chemotherapeutic drug discovery efforts. Two compounds with meta-methoxy substituents (2 and 3) maintained comparable antiproliferative activity with curcumin (1). In contrast, the acetoxy-curcuminoids (8-14) showed moderate to potent activity against all three cancer cell lines tested (Table 1). In particular, the colon cancer cell (HCT116) was most susceptible to the acetoxy-curcuminoids (8-12, Table 1) to show 2-2.5 times increase in EC 50 values compared with that of curcumin (1, Table 1). In this series, like the simple curcuminoids (2-7), the aromatic meta-methoxy substituent turned out to be critical for the antiproliferative effect, and the corresponding acetoxy-curcuminoids 10 and 11 showed the most potent activity against HCT116 with EC 50 values of 18.5 μM and 16.9 μM, respectively. Also noteworthy is the broad spectrum antiproliferative effect of the acetoxy-curcuminoid 11 with a free catechol moiety, which exhibited almost similar antiproliferative activity against all three cancer cell lines tested. Taken together, through evaluation of solubility as well as antiproliferative effect of the acetoxy-curcuminoids, we figured out that the acetoxy group substituted at the central methylene unit which served to enhance the solubility of the corresponding curcuminoids also played a key role in potentiating their antiproliferative effect. Thus, upon combination of the methylenyl acetoxy group and the aromatic meta-methoxy group on the curcumin framework

High-speed organocatalytic polymerization of a renewable methylene butyrolactone by a phosphazene superbase

KAUST Repository

Schmitt, Meghan L.; Falivene, Laura; Caporaso, Lucia; Cavallo, Luigi; Chen, Eugene You Xian

2014-01-01

The organic phosphazene superbase, 1-tert-butyl-4,4,4-tris(dimethylamino)- 2,2-bis[tris(dimethylamino)phosphoranylid-enamino]-2λ5, 4λ5-catenadi(phosphazene) (t-Bu-P4), is found to directly initiate high-speed polymerization of the biomass-derived renewable γ-methyl-α-methylene-γ-butyrolactone (MMBL), in contrast to other polymerization systems using t-Bu-P4 which typically require addition of an organic acid or a nucleophile as a co-initiating component. This MMBL polymerization by t-Bu-P4 alone is extremely rapid; even with a low t-Bu-P4 loading of 0.1 mol% or 0.02 mol%, quantitative monomer conversion is achieved in 20 s or 1 min, respectively, affording medium to high molecular weight PMMBL bioplastics in a catalytic fashion. The combined experimental and theoretical/computational studies have yielded mechanisms of chain initiation through abstraction of a proton from a monomer by t-Bu-P 4, essentially barrier-less chain propagation through rapid conjugate addition of the enolate anion stabilized by the nano-size cation [t-Bu-P 4H]+ to the monomer, and chain termination through chain transfer to the monomer which generates a saturated termination chain end and the [t-Bu-P4H]+-stabilized anionic active species that starts a new chain. This journal is © the Partner Organisations 2014.

Characterizing the discoloration of methylene blue in Fe0/H2O systems.

Science.gov (United States)

Noubactep, C

2009-07-15

Methylene blue (MB) was used as a model molecule to characterize the aqueous reactivity of metallic iron in Fe(0)/H(2)O systems. Likely discoloration mechanisms under used experimental conditions are: (i) adsorption onto Fe(0) and Fe(0) corrosion products (CP), (ii) co-precipitation with in situ generated iron CP, (iii) reduction to colorless leukomethylene blue (LMB). MB mineralization (oxidation to CO(2)) is not expected. The kinetics of MB discoloration by Fe(0), Fe(2)O(3), Fe(3)O(4), MnO(2), and granular activated carbon were investigated in assay tubes under mechanically non-disturbed conditions. The evolution of MB discoloration was monitored spectrophotometrically. The effect of availability of CP, Fe(0) source, shaking rate, initial pH value, and chemical properties of the solution were studied. The results present evidence supporting co-precipitation of MB with in situ generated iron CP as main discoloration mechanism. Under high shaking intensities (>150 min(-1)), increased CP generation yields a brownish solution which disturbed MB determination, showing that a too high shear stress induced the suspension of in situ generated corrosion products. The present study clearly demonstrates that comparing results from various sources is difficult even when the results are achieved under seemingly similar conditions. The appeal for an unified experimental procedure for the investigation of processes in Fe(0)/H(2)O systems is reiterated.

Enhanced photocatalytic degradation of methylene blue by ZnO-reduced graphene oxide composite synthesized via microwave-assisted reaction

Energy Technology Data Exchange (ETDEWEB)

Lv Tian [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai, 200062 (China); Pan Likun, E-mail: lkpan@phy.ecnu.edu.cn [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai, 200062 (China); Liu Xinjuan; Lu Ting; Zhu Guang; Sun Zhuo [Engineering Research Center for Nanophotonics and Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai, 200062 (China)

2011-10-13

Highlights: > ZnO-reduced graphene oxide composite is synthesized via microwave assisted reaction. > The method allows a facile, safe and rapid reaction in aqueous media. > A high dye degradation efficiency is achieved under UV light irradiation. - Abstract: A quick and facile microwave-assisted reaction is used to synthesize ZnO-reduced graphene oxide (RGO) hybrid composites by reducing graphite oxide dispersion with zinc nitrate using a microwave synthesis system. Their photocatalytic performance in degradation of methylene blue is investigated and the results show that the RGO plays an important role in the enhancement of photocatalytic performance and the ZnO-RGO composite with 1.1 wt. % RGO achieves a maximum degradation efficiency of 88% in a neutral solution under UV light irradiation for 260 min as compared with pure ZnO (68%) due to the increased light absorption, the reduced charge recombination with the introduction of RGO.

Single-Frame Cinema. Three Dimensional Computer-Generated Imaging.

Science.gov (United States)

Cheetham, Edward Joseph, II

This master's thesis provides a description of the proposed art form called single-frame cinema, which is a category of computer imagery that takes the temporal polarities of photography and cinema and unites them into a single visual vignette of time. Following introductory comments, individual chapters discuss (1) the essential physical…

Adsorption of Methylene Blue Malachite Green from aqueous solution on the surface of Wool Carbonizing Waste

International Nuclear Information System (INIS)

Khan, A. R.; Tahir, H.; Fahimuddin; Waqar, S. S.

2005-01-01

With ever increasing environmental pollution problems, the present day study was related to the removal of colorants. Synthetic colorants represented a relatively large group of organic chemicals. Such chemicals have undesirable effects not only on the environment but also on human beings. Present study is related with the removal of basic dyes methylene blue and malachite green using wool carbonizing waste materials as adsorbent. Adsorption of dyes is carried out as a function of temperature, amount of adsorbent, pH and duration. Spectrophotomeric technique was adopted for measuring the extent of adsorption. The data are fitted in Langmuir and Freundlich isotherm equations and their corresponding constants are calculated. Thermodynamic study is also carried out by calculating the values of thermodynamic parameters such as, enthalpy change (delta H), free energy change (delta G) and entropy change (delta S). The values of percent removal and KD for each dye system is also calculated at the range of temperatures ranging from 293-323K with the intervals of 10C+-0.2C. (author)

Studies on Biosorption of Methylene Blue from Aqueous Solutions by Powdered Palm Tree Flower (Borassus flabellifer

Directory of Open Access Journals (Sweden)

M. Srinivas Kini

2014-01-01

Full Text Available Biosorption experiments were carried out for the removal of methylene blue (MB using palm tree male flower (PTMF as the biosorbent at various pH, temperature, biosorbent, and adsorbate concentration. The optimum pH was found to be 6.0. The kinetic data were fitted in pseudofirst-order and second-order models. The equilibrium data were well-fitted in Langmuir isotherm and the maximum equilibrium capacities of the biosorbent were found to be 143.6, 153,9, 157.3 mg/g at 303, 313, and 323 K, respectively. Thermodynamic data for the adsorption system indicated spontaneous and endothermic process. The enthalpy and entropy values for adsorption were obtained as 15.06 KJ/mol and 0.129 KJ/mol K, respectively, in the temperature range of 303–323 K. A mathematical model for MB transported by molecular diffusion from the bulk of the solution to the surface of PTMF was derived and the values of liquid phase diffusivity and external mass transfer coefficient were estimated.

Antimicrobial photodynamic inactivation of Staphylococcus aureus biofilms in bone specimens using methylene blue, toluidine blue ortho and malachite green: An in vitro study.

Science.gov (United States)

Rosa, Luciano Pereira; da Silva, Francine Cristina; Nader, Sumaia Alves; Meira, Giselle Andrade; Viana, Magda Souza

2015-05-01

To evaluate the in vitro effectiveness of APDI with a 660 nm laser combined with methylene blue (MB), toluidine blue ortho (TBO) and malachite green (MG) dyes to inactivate Staphylococcus aureus (ATCC 25923) biofilms in compact and cancellous bone specimens. Eighty specimens of compact and 80 of cancellous bone were contaminated with a standard suspension of the microorganism and incubated for 14 days at 37°C to form biofilms. After this period, the specimens were divided into groups (n=10) according to established treatment: PS-L- (control - no treatment); PSmb+L-, PStbo+L-, PSmg+L- (only MB, TBO or MG for 5 min in the dark); PS-L+ (only laser irradiation for 180 s); and APDImb, APDItbo and APDImg (APDI with MB, TBO or MG for 180 s). The findings were statistically analyzed by ANOVA at 5% significance levels. All experimental treatments showed significant reduction of log CFU/mL S. aureus biofilms when compared with the control group for compact and cancellous bones specimens; the APDI group's treatment was more effective. The APDI carried out for the compact specimens showed better results when compared with cancellous specimens at all times of application. For the group of compact bone, APDImg showed greater reductions in CFU/mL (4.46 log 10). In the group of cancellous bone, the greatest reductions were found in the APDImb group (3.06 log 10). APDI with methylene blue, toluidine blue ortho and malachite green dyes and a 660 nm laser proved to be effective in the inactivation of S. aureus biofilms formed in compact and cancellous bone. Copyright © 2015 Elsevier Ltd. All rights reserved.

In vitro modulation of cytochrome P450 reductase supported indoleamine 2,3-dioxygenase activity by allosteric effectors cytochrome b(5) and methylene blue.

Science.gov (United States)

Pearson, Josh T; Siu, Sophia; Meininger, David P; Wienkers, Larry C; Rock, Dan A

2010-03-30

Indoleamine 2,3-dioxygenase (IDO) is a heme-containing dioxygenase involved in the degradation of several indoleamine derivatives and has been indicated as an immunosuppressive. IDO is an attractive target for therapeutic intervention in diseases which are known to capitalize on immune suppression, including cancer, HIV, and inflammatory diseases. Conventionally, IDO activity is measured through chemical reduction by the addition of ascorbate and methylene blue. Identification of potential coenzymes involved in the reduction of IDO in vivo should improve in vitro reconstitution systems used to identify potential IDO inhibitors. In this study we show that NADPH-cytochrome P450 reductase (CPR) is capable of supporting IDO activity in vitro and that oxidation of l-Trp follows substrate inhibition kinetics (k(cat) = 0.89 +/- 0.04 s(-1), K(m) = 0.72 +/- 0.15 microM, and K(i) = 9.4 +/- 2.0 microM). Addition of cytochrome b(5) to CPR-supported l-Trp incubations results in modulation from substrate inhibition to sigmoidal kinetics (k(cat) = 1.7 +/- 0.3 s(-1), K(m) = 1.5 +/- 0.9 microM, and K(i) = 1.9 +/- 0.3). CPR-supported d-Trp oxidations (+/-cytochrome b(5)) exhibit Michaelis-Menten kinetics. Addition of methylene blue (minus ascorbate) to CPR-supported reactions resulted in inhibition of d-Trp turnover and modulation of l-Trp kinetics from allosteric to Michaelis-Menten with a concurrent decrease in substrate affinity for IDO. Our data indicate that CPR is capable of supporting IDO activity in vitro and oxidation of tryptophan by IDO displays substrate stereochemistry dependent atypical kinetics which can be modulated by the addition of cytochrome b(5).

Can methylene blue dye be used as an alternative to patent blue dye to find the sentinel lymph node in breast cancer surgery?

Directory of Open Access Journals (Sweden)

Asieh Sadat Fattahi

2014-01-01

Full Text Available Background: Sentinel lymph node biopsy (SLNB is standard care to evaluate axillary involvement in early breast cancer. It has fewer complications than complete lymph node dissection; however, using blue dye in SLNB is controversial. We have evaluated the detection rate and local complications associated with methylene blue dye (MBD used in SLNB in early breast cancer patients and compared these results to patent blue dye (PBD. Materials and Methods : In a cohort prospective study, 312 patients with early breast cancer without axillary lymph node involvement were divided into two groups according to dye type. All of the patients received radiotracer and one type of blue dye. We filled out a checklist for the patients that contained demographic data, size of tumor, stage, detection of sentinel lymph node, and complications and then analyzed the data. Results: Demographic and histopathologic characteristics were not significantly different in both groups. Mean (standard deviation [SD] tumor size in all patients was 2.4 (0.8 cm. Detection rate in the MBD group was 77.5% with dye alone and 94.2% with dye and radioisotope; and in the PBD group it was 80.1% and 92.9% respectively (P > 0.05. We had blue discoloration of the skin in 23.7% in the PBD and 14.1% in the MBD group (P < 0.05 local inflammation was detected in one patient in the PBD and five in the MBD group (P < 0.05. Skin necrosis and systemic complications were not observed. Conclusion: Methylene blue has an acceptable detection rate, which may be a good alternative in SLNB. Complication such as blue discoloration of the skin was also lower with MBD.

The use of chemical modified chitosan with succinic anhydride in the methylene blue adsorption; O emprego de quitosana quimicamente modificada com anidrido succinico na adsorcao de azul de metileno

Energy Technology Data Exchange (ETDEWEB)

Lima, Ilauro S.; Ribeiro, Emerson S.; Airoldi, Claudio [Universidade Estadual de Campinas, SP (Brazil). Inst. de Quimica]. E-mail: airoldi@iqm.unicamp.br

2006-05-15

The adsorption capacity of a-chitosan and its modified form with succinic anhydride was compared with the traditional adsorbent active carbon by using the dye methylene blue, employed in the textile industry. The isotherms for both biopolymers were classified as SSA systems in the Giles model, more specifically iclass and subgroup 3. The dye concentration in the supernatant in the adsorption assay was determined through electronic spectroscopy. By calorimetric titration thermodynamic data of the interaction between methylene blue and the chemically modified chitosan at the solid/liquid interface were obtained. The enthalpy of the dye/chitosan interaction gave 2.47 {+-} 0.02 kJ mol-1 with an equilibrium constant of 7350 {+-} 10 and for the carbon/dye interaction this constant gave 5951 {+-} 8. The spontaneity of these adsorptions are reflected by the free Gibbs energies of -22.1 {+-} 0.4 and -21.5 {+-} 0.2 kJ mol-1, respectively, found for these systems. This new adsorbent derived from a natural polysaccharide is as efficient as activated carbon. However 97% of the bonded dye can be eluted by sodium chloride solution, while this same operation elutes only 42% from carbon. Chitosan is efficient in dye removal with the additional advantage of being cheap, non-toxic, biocompatible and biodegradable. (author)

Methylene blue adsorption of GMZ bentonite and the effect of hyper-alkaline solution erosion

International Nuclear Information System (INIS)

Chen Bao; Zhang Huixin; Zhu Chunming; Chen Ping

2012-01-01

The method of combining the halo method with the spectrometer method, was used to study on the Methylene blue (MB) adsorption of Gaomiaozi (GMZ) bentonite, which had been eroded by hyper-alkaline solution, to investigate the mechanism of the effect of hyper-alkaline pore water on the buffer/backfill properties of GMZ bentonite. Results present, method employed in this article is brief and feasible, and high accuracy; The total specific surface area calculated by the test of MB adsorption is more accurate than the method of ethylene glycol monomethyl ether (EGIVIE). The MB adsorption of samples, which had been eroded by hyper-alkaline solution, decreases with the increase of the concentration of hyper-alkaline solution, and the change law agrees with the variation of the mass percentage of montmorillonite in bentonite tested by X- Ray diffraction (XRD). Therefore, the erosion of hyper-alkaline pore water might dissolve montmorillonite, which is the effective composition of bentonite, and destroy the tetrahedron- octahedron-tetrahedron (T-O-T) structure of montmorillonite, then lead to the decrease of cation exchange capability and the specific surface area of montmorillonite, and the the macroscopic expressions are the decrease of MB adsorption, the swelling potential and the increase of permeability. (authors)

Green synthesis of halloysite nanotubes supported Ag nanoparticles for photocatalytic decomposition of methylene blue

International Nuclear Information System (INIS)

Zou Meiling; Zhu Han; Xu Congsheng; Du Mingliang; Fu Yaqin

2012-01-01

Using tea polyphenols (TPs) as a reductant, Ag nanoparticles (AgNPs) supported on halloysite nanotubes (HNTs) were simply and greenly synthesized for the photocatalytic decomposition of methylene blue (MB). HNTs were initially functionalized by N-β-aminoethyl-γ-aminopropyl trimethoxysilane (AEAPTMS) to introduce amino groups to form N-HNTs to fasten the AgNPs; then AgNPs were synthesized and ‘anchored’ on the surface of the HNTs. Fourier transform infrared spectroscopy was employed to testify the amino groups on the surface of the HNTs. Transmission electron microscopy, field-emission scanning electron microscopy and x-ray diffraction were utilized to characterize the structure and morphology of the synthesized HNTs supported by the AgNPs (AgNPs-N-HNTs). The results showed that the AgNPs had been synthesized and ‘anchored’ onto the surface of the HNTs with a diameter of about 20-30 nm. X-ray photoelectron spectroscopy analysis revealed the chelating interaction between the AgNPs and N atoms together with the TP molecular. The photocatalytic activity of the as-prepared AgNPs-N-HNTs catalyst was evaluated by decomposition of MB; the results showed that the prepared catalyst exhibited excellent catalytic activity and high adsorption capability to MB. (paper)

Extraosseous uptake of technetium-99m methylene diphosphonate by an acute territorial cerebral infarct in a classical biodistribution pattern

International Nuclear Information System (INIS)

Kannivelu, Anbalagan; Padhy, Ajit Kumar; Srinivasan, Sivasubramanian; Ali, Syed Zama

2013-01-01

Technetium-99m methylene diphosphonate scintigraphy is usually performed to assess bone lesions, especially skeletal metastases in patients with a history of malignancy. However, it is important to recognize some specific conditions with a unique pattern of tracer uptake, especially in extraosseous locations as they are not related to primary neoplasm or metastases. Diagnosing such unusual presentation is essential as it significantly influences the clinical management. This case report describes an unusual presentation detected in a bone scan of an elderly female patient, who was a treated case of breast cancer and was referred for a bone scan to rule out bone metastases. Incidentally, a large acute territorial cerebral infarct was diagnosed, which was later confirmed by magnetic resonance imaging on diffusion-weighted images. Diagnosis of the typical presentation and timely management saved the patient life. (author)

31 CFR 223.14 - Schedules of single risks.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Schedules of single risks. 223.14 Section 223.14 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL... UNITED STATES § 223.14 Schedules of single risks. During the months of January, April, July, and October...

Synthesis, Characterization and Antimicrobial Activity of Metal Chelates of 5-[4-Chloro phenyl(1, 3, 4thiadiazol-2-ylamino methylene]-8-hydroxy quinoline

Directory of Open Access Journals (Sweden)

Divyesh K. Patel

2009-01-01

Full Text Available 5-Chloromethyl-8-quinolinol was condensed stoichiometrically with 5-(4-chlorophenyl-(1,3,4 thiadiazol-2-ylamine in the presence of sodium bicarbonate. The resulting 5-[4-chlorophenyl-(1,3,4thiadiazol-2-ylamino methylene]-8-quinolinol (CTAQ was characterized by elemental analysis and spectral studies. The transition metal chelates viz. Cu2+, Ni2+, Co2+, Mn2+ and Zn2+ of CTAQ were prepared and characterized by metal-ligand (M:L ratio, IR and reflectance spectroscopies and magnetic properties. The antifungal activity of CTAQ and its metal chelates was screened against various fungi. The results show that all these samples are good antifungal agents.

Modified solvothermal synthesis of cobalt ferrite (CoFe2O4) magnetic nanoparticles photocatalysts for degradation of methylene blue with H2O2/visible light

Science.gov (United States)

Kalam, Abul; Al-Sehemi, Abdullah G.; Assiri, Mohammed; Du, Gaohui; Ahmad, Tokeer; Ahmad, Irfan; Pannipara, M.

2018-03-01

Different grads of magnetic nano-scaled cobalt ferrites (CoFe2O4) photocatalysts were synthesized by modified Solvothermal (MST) process with and without polysaccharide. The indigenously synthesized photocatalysts were characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), thermo gravimetric analysis (TGA), Fourier transform infrared (FT-IR), UV-visible (UV-vis) spectroscopy and N2 adsorption-desorption isotherm method. The Fourier transform infrared spectroscopy study showed the Fe-O stretching vibration 590-619 cm-1, confirming the formation of metal oxide. The crystallite size of the synthesized photocatalysts was found in the range between 20.0 and 30.0 nm. The surface area of obtained magnetic nanoparticles is found to be reasonably high in the range of 63.0-76.0 m2/g. The results shown that only MST-2 is the most active catalyst for photo-Fenton like scheme for fast photodegradation action of methylene blue dye, this is possible due to optical band gap estimated of 2.65 eV. Captivatingly the percentage of degradation efficiency increases up to 80% after 140 min by using MST-2 photocatalyst. Photocatalytic degradation of methylene blue (MB) dye under visible light irradiation with cobalt ferrite magnetic nanoparticles followed first order kinetic constant and rate constant of MST-2 is almost 2.0 times greater than MST-1 photocatalyst.

Comparing transfusion reaction rates for various plasma types: a systematic review and meta-analysis/regression.

Science.gov (United States)

Saadah, Nicholas H; van Hout, Fabienne M A; Schipperus, Martin R; le Cessie, Saskia; Middelburg, Rutger A; Wiersum-Osselton, Johanna C; van der Bom, Johanna G

2017-09-01

We estimated rates for common plasma-associated transfusion reactions and compared reported rates for various plasma types. We performed a systematic review and meta-analysis of peer-reviewed articles that reported plasma transfusion reaction rates. Random-effects pooled rates were calculated and compared between plasma types. Meta-regression was used to compare various plasma types with regard to their reported plasma transfusion reaction rates. Forty-eight studies reported transfusion reaction rates for fresh-frozen plasma (FFP; mixed-sex and male-only), amotosalen INTERCEPT FFP, methylene blue-treated FFP, and solvent/detergent-treated pooled plasma. Random-effects pooled average rates for FFP were: allergic reactions, 92/10 5 units transfused (95% confidence interval [CI], 46-184/10 5 units transfused); febrile nonhemolytic transfusion reactions (FNHTRs), 12/10 5 units transfused (95% CI, 7-22/10 5 units transfused); transfusion-associated circulatory overload (TACO), 6/10 5 units transfused (95% CI, 1-30/10 5 units transfused); transfusion-related acute lung injury (TRALI), 1.8/10 5 units transfused (95% CI, 1.2-2.7/10 5 units transfused); and anaphylactic reactions, 0.8/10 5 units transfused (95% CI, 0-45.7/10 5 units transfused). Risk differences between plasma types were not significant for allergic reactions, TACO, or anaphylactic reactions. Methylene blue-treated FFP led to fewer FNHTRs than FFP (risk difference = -15.3 FNHTRs/10 5 units transfused; 95% CI, -24.7 to -7.1 reactions/10 5 units transfused); and male-only FFP led to fewer cases of TRALI than mixed-sex FFP (risk difference = -0.74 TRALI/10 5 units transfused; 95% CI, -2.42 to -0.42 injuries/10 5 units transfused). Meta-regression demonstrates that the rate of FNHTRs is lower for methylene blue-treated compared with FFP, and the rate of TRALI is lower for male-only than for mixed-sex FFP; whereas no significant differences are observed between plasma types for allergic reactions, TACO

Synthesis and photocatalytic degradation study of methylene blue dye under visible light irradiation by Fe1-xBixVO4 solid solutions (0 ≤ x ≤ 1.0)

Science.gov (United States)

Bera, Ganesh; Reddy, V. R.; Mal, Priyanath; Das, Pradip; Turpu, G. R.

2018-05-01

The novel hetero-structures Fe1-xBixVO4 solid solutions (0 ≤ x ≤ 1.0) with the two dissimilar end member of FeVO4 - BiVO4, were successfully synthesized by the standard solid state reaction method. The structural and chemical properties of as prepared photo-catalyst samples were characterized by X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FT-IR) and UV-visible absorption spectroscopy techniques. It is confirmed from the results of XRD, Raman and FT-IR that FeVO4 and BiVO4 are in triclinic (space group P-1 (2)) and monoclinic (space group I2/b (15)) phases respectively. The Bi incorporation into Fe site of FeVO4 emerges as hetero-structures of both the end members of the solid solutions. In addition, the photocatalytic activity in the degradation of methylene blue (MB) dye under visible light irradiation was carried out through UV-visible spectroscopy measurement of photo-catalysts FeVO4, BiVO4 and mixed phases of both photo-catalyst. The results indicate that under visible light irradiation the photocatalytic activity of mixed phases were very effective and higher than the both single phases of the solid solutions. The composition x= 0.25 exhibits an excellent photocatalytic property for the degradation of MB solution under visible light irradiation rather than other.

This immortal coil? New CT rigs duel against singles

Energy Technology Data Exchange (ETDEWEB)

Creighton, J.

1998-12-01

New competition to conventional single rigs that have changed little in the last four decades face new competition from next-generation coiled tubing (CT) units which have multi-function capabilities, ranging from driving onto leases, drilling and setting surface case to cementing. Several of these new units are ready to challenge the conventional single rigs. Their ability to perform at high penetration rates (up to twice what single rigs can do) is expected to significantly cut drill time, with corresponding cost savings for both contractors and operators. Serval Corporation and Fleet Coiled Services are just two of the drilling service companies that have launched new shallow grass roots coiled tubing drilling units recently, gambling that the new technology will win over conventional methods hands down. Some major companies, like Fracmaster Ltd. and NOWSCO Well Service Ltd., have targeted the re-entry and horizontal markets, a much more difficult technical challenge, sinking billions of dollars of research and development money into advancing the most technically difficult applications of coil technology.

Visible light driven photocatalytic degradation of methylene blue using novel camphor sulfonic acid doped polycarbazole/g-C3N4 nanocomposite

Science.gov (United States)

Praveena, P.; Dhanavel, S.; Sangamithirai, D.; Narayanan, V.; Stephen, A.

2018-04-01

A novel polycabazole(PCz)/graphitic carbon nitride(g-C3N4) nanocomposite was synthesized via chemical oxidative polymerization method. In the present work, camphor sulfonic acid (CSA) was used as a dopantand ammonium peroxydisulphate (APS) was used as an oxidizing agent. The PCz/g-C3N4 nanocompositewas characterizedusing X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and UV-Visible spectroscopy (UV-Vis). The obtained results confirm the successful formation of PCz/g-C3N4 nanocomposite. Visible light induced photocatalytic activity of the novel catalyst was demonstrated using methylene blue as a target pollutant. The results suggestthat PCz/g-C3N4 nanocomposite can be used as an effective catalyst for the degradation of organic pollutants from waste water.

Single-Sex versus Secondary Schooling: A Systematic Review

Science.gov (United States)

Mael, Fred; Alonso, Alex; Gibson, Doug; Rogers, Kelly; Smith, Mark

2005-01-01

Single-sex education refers most generally to education at the elementary, secondary, or postsecondary level in which males or females attend school exclusively with members of their own sex. This report deals primarily with single-sex education at the elementary and secondary levels. Research in the United States on the question of whether public…

Single Parenthood and Children's Reading Performance in Asia

Science.gov (United States)

Park, Hyunjoon

2007-01-01

Using the data from Program for International Student Assessment, I examine the gap in reading performance between 15-year-old students in single-parent and intact families in 5 Asian countries in comparison to the United States. The ordinary least square regression analyses show negligible disadvantages of students with a single parent in Hong…