WorldWideScience

Sample records for simplified normal limits

  1. Setting limits on supersymmetry using simplified models

    CERN Document Server

    Gutschow, C.

    2012-01-01

    Experimental limits on supersymmetry and similar theories are difficult to set because of the enormous available parameter space and difficult to generalize because of the complexity of single points. Therefore, more phenomenological, simplified models are becoming popular for setting experimental limits, as they have clearer physical implications. The use of these simplified model limits to set a real limit on a concrete theory has not, however, been demonstrated. This paper recasts simplified model limits into limits on a specific and complete supersymmetry model, minimal supergravity. Limits obtained under various physical assumptions are comparable to those produced by directed searches. A prescription is provided for calculating conservative and aggressive limits on additional theories. Using acceptance and efficiency tables along with the expected and observed numbers of events in various signal regions, LHC experimental results can be re-cast in this manner into almost any theoretical framework, includ...

  2. A simplified technique for shakedown limit load determination

    International Nuclear Information System (INIS)

    Abdalla, Hany F.; Megahed, Mohammad M.; Younan, Maher Y.A.

    2007-01-01

    In this paper, a simplified technique is presented to determine the shakedown limit load of a structure using the finite element method. The simplified technique determines the shakedown limit load without performing lengthy time consuming full elastic-plastic cyclic loading simulations or conventional iterative elastic techniques. Instead, the shakedown limit load is determined by performing two analyses namely: an elastic analysis and an elastic-plastic analysis. By extracting the results of the two analyses, the shakedown limit load is determined through the calculation of the residual stresses developed within the structure. The simplified technique is applied and verified using two bench mark shakedown problems namely: the two-bar structure subjected to constant axial force and cyclic thermal loading, and the Bree cylinder subjected to constant internal pressure and cyclic high temperature variation across its wall. The results of the simplified technique showed very good correlation with the, analytically determined, Bree diagrams of both structures. In order to gain confidence in the simplified technique, the shakedown limit loads output by the simplified technique are used to perform full elastic-plastic cyclic loading simulations to check for shakedown behavior of both structures

  3. Limiting Normal Operator in Quasiconvex Analysis

    Czech Academy of Sciences Publication Activity Database

    Aussel, D.; Pištěk, Miroslav

    2015-01-01

    Roč. 23, č. 4 (2015), s. 669-685 ISSN 1877-0533 R&D Projects: GA ČR GA15-00735S Institutional support: RVO:67985556 Keywords : Quasiconvex function * Sublevel set * Normal operator Subject RIV: BA - General Mathematics Impact factor: 0.973, year: 2015 http://library.utia.cas.cz/separaty/2015/MTR/pistek-0453552.pdf

  4. A simplified Excel® algorithm for estimating the least limiting water range of soils

    Directory of Open Access Journals (Sweden)

    Leão Tairone Paiva

    2004-01-01

    Full Text Available The least limiting water range (LLWR of soils has been employed as a methodological approach for evaluation of soil physical quality in different agricultural systems, including forestry, grasslands and major crops. However, the absence of a simplified methodology for the quantification of LLWR has hampered the popularization of its use among researchers and soil managers. Taking this into account this work has the objective of proposing and describing a simplified algorithm developed in Excel® software for quantification of the LLWR, including the calculation of the critical bulk density, at which the LLWR becomes zero. Despite the simplicity of the procedures and numerical techniques of optimization used, the nonlinear regression produced reliable results when compared to those found in the literature.

  5. Simplified analytical modeling of the normal hole erosion test; Modelado analitico simplificado del ensayo normal de ersoion de tubo

    Energy Technology Data Exchange (ETDEWEB)

    Khamlichi, A.; Bezzazi, M.; El Bakkali, L.; Jabbouri, A.; Kissi, B.; Yakhlef, F.; Parron Vera, M. A.; Rubio Cintas, M. D.; Castillo Lopez, O.

    2009-07-01

    The role erosion test was developed in order to study erosion phenomenon which occurs in cracks appearing in hydraulic infrastructures such as dams. This test enables describing experimentally the erosive characteristics of soils by means of an index which is called erosion rate and a critical tension which indicates the threshold of surface erosion initiation. The objective of this work is to five modelling of this experiment by means of a simplified analytical approach. The erosion law is derived by taking into account the flow regime. This law shows that the erosion occurring in the tube is controlled by a first order dynamics where only two parameters are involved: the characteristic's time linked to the erosion rate and the stress shear threshold for which erosion begins to develop. (Author) 5 refs.

  6. Illumination normalization based on simplified local binary patterns for a face verification system

    NARCIS (Netherlands)

    Tao, Q.; Veldhuis, Raymond N.J.

    2007-01-01

    Illumination normalization is a very important step in face recognition. In this paper we propose a simple implementation of Local Binary Patterns, which effectively reduces the variability caused by illumination changes. In combination with a likelihood ratio classifier, this illumination

  7. Simplified calculation method for radiation dose under normal condition of transport

    International Nuclear Information System (INIS)

    Watabe, N.; Ozaki, S.; Sato, K.; Sugahara, A.

    1993-01-01

    In order to estimate radiation dose during transportation of radioactive materials, the following computer codes are available: RADTRAN, INTERTRAN, J-TRAN. Because these codes consist of functions for estimating doses not only under normal conditions but also in the case of accidents, when nuclei may leak and spread into the environment by air diffusion, the user needs to have special knowledge and experience. In this presentation, we describe how, with a view to preparing a method by which a person in charge of transportation can calculate doses in normal conditions, the main parameters upon which the value of doses depends were extracted and the dose for a unit of transportation was estimated. (J.P.N.)

  8. A Simplified Procedure for Reliability Estimation of Underground Concrete Barriers against Normal Missile Impact

    Directory of Open Access Journals (Sweden)

    N. A. Siddiqui

    2011-06-01

    Full Text Available Underground concrete barriers are frequently used to protect strategic structures like Nuclear power plants (NPP, deep under the soil against any possible high velocity missile impact. For a given range and type of missile (or projectile it is of paramount importance to examine the reliability of underground concrete barriers under expected uncertainties involved in the missile, concrete, and soil parameters. In this paper, a simple procedure for the reliability assessment of underground concrete barriers against normal missile impact has been presented using the First Order Reliability Method (FORM. The presented procedure is illustrated by applying it to a concrete barrier that lies at a certain depth in the soil. Some parametric studies are also conducted to obtain the design values which make the barrier as reliable as desired.

  9. Reynolds number limits for jet propulsion: a numerical study of simplified jellyfish.

    Science.gov (United States)

    Herschlag, Gregory; Miller, Laura

    2011-09-21

    The Scallop theorem states that reciprocal methods of locomotion, such as jet propulsion or paddling, will not work in Stokes flow (Reynolds number=0). In nature the effective limit of jet propulsion is still in the range where inertial forces are significant. It appears that almost all animals that use jet propulsion swim at Reynolds numbers (Re) of about 5 or more. Juvenile squid and octopods hatch from the egg already swimming in this inertial regime. Juvenile jellyfish, or ephyrae, break off from polyps swimming at Re greater than 5. Many other organisms, such as scallops, rarely swim at Re less than 100. The limitations of jet propulsion at intermediate Re is explored here using the immersed boundary method to solve the 2D Navier-Stokes equations coupled to the motion of a simplified jellyfish. The contraction and expansion kinematics are prescribed, but the forward and backward swimming motions of the idealized jellyfish are emergent properties determined by the resulting fluid dynamics. Simulations are performed for both an oblate bell shape using a paddling mode of swimming and a prolate bell shape using jet propulsion. Average forward velocities and work put into the system are calculated for Re between 1 and 320. The results show that forward velocities rapidly decay with decreasing Re for all bell shapes when Re<10. Similarly, the work required to generate the pulsing motion increases significantly for Re<10. When compared to actual organisms, the swimming velocities and vortex separation patterns for the model prolate agree with those observed in Nemopsis bachei. The forward swimming velocities of the model oblate jellyfish after two pulse cycles are comparable to those reported for Aurelia aurita, but discrepancies are observed in the vortex dynamics between when the 2D model oblate jellyfish and the organism. This discrepancy is likely due to a combination of the differences between the 3D reality of the jellyfish and the 2D simplification, as well as

  10. Evaluating Complex Interventions and Health Technologies Using Normalization Process Theory: Development of a Simplified Approach and Web-Enabled Toolkit

    LENUS (Irish Health Repository)

    May, Carl R

    2011-09-30

    Abstract Background Normalization Process Theory (NPT) can be used to explain implementation processes in health care relating to new technologies and complex interventions. This paper describes the processes by which we developed a simplified version of NPT for use by clinicians, managers, and policy makers, and which could be embedded in a web-enabled toolkit and on-line users manual. Methods Between 2006 and 2010 we undertook four tasks. (i) We presented NPT to potential and actual users in multiple workshops, seminars, and presentations. (ii) Using what we discovered from these meetings, we decided to create a simplified set of statements and explanations expressing core constructs of the theory (iii) We circulated these statements to a criterion sample of 60 researchers, clinicians and others, using SurveyMonkey to collect qualitative textual data about their criticisms of the statements. (iv) We then reconstructed the statements and explanations to meet users\\' criticisms, embedded them in a web-enabled toolkit, and beta tested this \\'in the wild\\'. Results On-line data collection was effective: over a four week period 50\\/60 participants responded using SurveyMonkey (40\\/60) or direct phone and email contact (10\\/60). An additional nine responses were received from people who had been sent the SurveyMonkey form by other respondents. Beta testing of the web enabled toolkit produced 13 responses, from 327 visits to http:\\/\\/www.normalizationprocess.org. Qualitative analysis of both sets of responses showed a high level of support for the statements but also showed that some statements poorly expressed their underlying constructs or overlapped with others. These were rewritten to take account of users\\' criticisms and then embedded in a web-enabled toolkit. As a result we were able translate the core constructs into a simplified set of statements that could be utilized by non-experts. Conclusion Normalization Process Theory has been developed through

  11. Evaluating complex interventions and health technologies using normalization process theory: development of a simplified approach and web-enabled toolkit

    Directory of Open Access Journals (Sweden)

    Murray Elizabeth

    2011-09-01

    Full Text Available Abstract Background Normalization Process Theory (NPT can be used to explain implementation processes in health care relating to new technologies and complex interventions. This paper describes the processes by which we developed a simplified version of NPT for use by clinicians, managers, and policy makers, and which could be embedded in a web-enabled toolkit and on-line users manual. Methods Between 2006 and 2010 we undertook four tasks. (i We presented NPT to potential and actual users in multiple workshops, seminars, and presentations. (ii Using what we discovered from these meetings, we decided to create a simplified set of statements and explanations expressing core constructs of the theory (iii We circulated these statements to a criterion sample of 60 researchers, clinicians and others, using SurveyMonkey to collect qualitative textual data about their criticisms of the statements. (iv We then reconstructed the statements and explanations to meet users' criticisms, embedded them in a web-enabled toolkit, and beta tested this 'in the wild'. Results On-line data collection was effective: over a four week period 50/60 participants responded using SurveyMonkey (40/60 or direct phone and email contact (10/60. An additional nine responses were received from people who had been sent the SurveyMonkey form by other respondents. Beta testing of the web enabled toolkit produced 13 responses, from 327 visits to http://www.normalizationprocess.org. Qualitative analysis of both sets of responses showed a high level of support for the statements but also showed that some statements poorly expressed their underlying constructs or overlapped with others. These were rewritten to take account of users' criticisms and then embedded in a web-enabled toolkit. As a result we were able translate the core constructs into a simplified set of statements that could be utilized by non-experts. Conclusion Normalization Process Theory has been developed through

  12. Normalized lift: an energy interpretation of the lift coefficient simplifies comparisons of the lifting ability of rotating and flapping surfaces.

    Directory of Open Access Journals (Sweden)

    Phillip Burgers

    Full Text Available For a century, researchers have used the standard lift coefficient C(L to evaluate the lift, L, generated by fixed wings over an area S against dynamic pressure, ½ρv(2, where v is the effective velocity of the wing. Because the lift coefficient was developed initially for fixed wings in steady flow, its application to other lifting systems requires either simplifying assumptions or complex adjustments as is the case for flapping wings and rotating cylinders.This paper interprets the standard lift coefficient of a fixed wing slightly differently, as the work exerted by the wing on the surrounding flow field (L/ρ·S, compared against the total kinetic energy required for generating said lift, ½v(2. This reinterpreted coefficient, the normalized lift, is derived from the work-energy theorem and compares the lifting capabilities of dissimilar lift systems on a similar energy footing. The normalized lift is the same as the standard lift coefficient for fixed wings, but differs for wings with more complex motions; it also accounts for such complex motions explicitly and without complex modifications or adjustments. We compare the normalized lift with the previously-reported values of lift coefficient for a rotating cylinder in Magnus effect, a bat during hovering and forward flight, and a hovering dipteran.The maximum standard lift coefficient for a fixed wing without flaps in steady flow is around 1.5, yet for a rotating cylinder it may exceed 9.0, a value that implies that a rotating cylinder generates nearly 6 times the maximum lift of a wing. The maximum normalized lift for a rotating cylinder is 1.5. We suggest that the normalized lift can be used to evaluate propellers, rotors, flapping wings of animals and micro air vehicles, and underwater thrust-generating fins in the same way the lift coefficient is currently used to evaluate fixed wings.

  13. Normalized Lift: An Energy Interpretation of the Lift Coefficient Simplifies Comparisons of the Lifting Ability of Rotating and Flapping Surfaces

    Science.gov (United States)

    Burgers, Phillip; Alexander, David E.

    2012-01-01

    For a century, researchers have used the standard lift coefficient CL to evaluate the lift, L, generated by fixed wings over an area S against dynamic pressure, ½ρv 2, where v is the effective velocity of the wing. Because the lift coefficient was developed initially for fixed wings in steady flow, its application to other lifting systems requires either simplifying assumptions or complex adjustments as is the case for flapping wings and rotating cylinders. This paper interprets the standard lift coefficient of a fixed wing slightly differently, as the work exerted by the wing on the surrounding flow field (L/ρ·S), compared against the total kinetic energy required for generating said lift, ½v2. This reinterpreted coefficient, the normalized lift, is derived from the work-energy theorem and compares the lifting capabilities of dissimilar lift systems on a similar energy footing. The normalized lift is the same as the standard lift coefficient for fixed wings, but differs for wings with more complex motions; it also accounts for such complex motions explicitly and without complex modifications or adjustments. We compare the normalized lift with the previously-reported values of lift coefficient for a rotating cylinder in Magnus effect, a bat during hovering and forward flight, and a hovering dipteran. The maximum standard lift coefficient for a fixed wing without flaps in steady flow is around 1.5, yet for a rotating cylinder it may exceed 9.0, a value that implies that a rotating cylinder generates nearly 6 times the maximum lift of a wing. The maximum normalized lift for a rotating cylinder is 1.5. We suggest that the normalized lift can be used to evaluate propellers, rotors, flapping wings of animals and micro air vehicles, and underwater thrust-generating fins in the same way the lift coefficient is currently used to evaluate fixed wings. PMID:22629326

  14. Normalized lift: an energy interpretation of the lift coefficient simplifies comparisons of the lifting ability of rotating and flapping surfaces.

    Science.gov (United States)

    Burgers, Phillip; Alexander, David E

    2012-01-01

    For a century, researchers have used the standard lift coefficient C(L) to evaluate the lift, L, generated by fixed wings over an area S against dynamic pressure, ½ρv(2), where v is the effective velocity of the wing. Because the lift coefficient was developed initially for fixed wings in steady flow, its application to other lifting systems requires either simplifying assumptions or complex adjustments as is the case for flapping wings and rotating cylinders.This paper interprets the standard lift coefficient of a fixed wing slightly differently, as the work exerted by the wing on the surrounding flow field (L/ρ·S), compared against the total kinetic energy required for generating said lift, ½v(2). This reinterpreted coefficient, the normalized lift, is derived from the work-energy theorem and compares the lifting capabilities of dissimilar lift systems on a similar energy footing. The normalized lift is the same as the standard lift coefficient for fixed wings, but differs for wings with more complex motions; it also accounts for such complex motions explicitly and without complex modifications or adjustments. We compare the normalized lift with the previously-reported values of lift coefficient for a rotating cylinder in Magnus effect, a bat during hovering and forward flight, and a hovering dipteran.The maximum standard lift coefficient for a fixed wing without flaps in steady flow is around 1.5, yet for a rotating cylinder it may exceed 9.0, a value that implies that a rotating cylinder generates nearly 6 times the maximum lift of a wing. The maximum normalized lift for a rotating cylinder is 1.5. We suggest that the normalized lift can be used to evaluate propellers, rotors, flapping wings of animals and micro air vehicles, and underwater thrust-generating fins in the same way the lift coefficient is currently used to evaluate fixed wings.

  15. Simplified seismic analysis applied to structures systems and components with limited radioactive inventories

    International Nuclear Information System (INIS)

    Stevenson, J.D.

    1989-01-01

    This paper presents a review of the current status of simplified methods of seismic design and analysis applicable to nuclear facility structures, systems and components important to public health and safety. In particular, the International Atomic Energy Agency, IAEA TEC DOC 348 procedure for structures and the Bounding Spectra Concept for equipment as being developed by Seismic Qualification Utility Group and the Electric Power Research Institute will be discussed in some detail

  16. Correlation of Normal Gravity Mixed Convection Blowoff Limits with Microgravity Forced Flow Blowoff Limits

    Science.gov (United States)

    Marcum, Jeremy W.; Olson, Sandra L.; Ferkul, Paul V.

    2016-01-01

    The axisymmetric rod geometry in upward axial stagnation flow provides a simple way to measure normal gravity blowoff limits to compare with microgravity Burning and Suppression of Solids - II (BASS-II) results recently obtained aboard the International Space Station. This testing utilized the same BASS-II concurrent rod geometry, but with the addition of normal gravity buoyant flow. Cast polymethylmethacrylate (PMMA) rods of diameters ranging from 0.635 cm to 3.81 cm were burned at oxygen concentrations ranging from 14 to 18% by volume. The forced flow velocity where blowoff occurred was determined for each rod size and oxygen concentration. These blowoff limits compare favorably with the BASS-II results when the buoyant stretch is included and the flow is corrected by considering the blockage factor of the fuel. From these results, the normal gravity blowoff boundary for this axisymmetric rod geometry is determined to be linear, with oxygen concentration directly proportional to flow speed. We describe a new normal gravity 'upward flame spread test' method which extrapolates the linear blowoff boundary to the zero stretch limit in order to resolve microgravity flammability limits-something current methods cannot do. This new test method can improve spacecraft fire safety for future exploration missions by providing a tractable way to obtain good estimates of material flammability in low gravity.

  17. A simplified Excel tool for implementation of RUSLE2 in vineyards for stakeholders with limited dataset

    Science.gov (United States)

    Gomez, Jose Alfonso; Biddoccu, Marcella; Guzmán, Gema; Cavallo, Eugenio

    2016-04-01

    Analysis with simulation models is in many situations the only way to evaluate the impact of changes in soil management on soil erosion risk, and the Revised Universal Soil Loss Equation RUSLE (Renard et al. 1997, Dabney et al. 2012) remains as the most widely used. Even with their relative simplicity compared to other, more process based, erosion models proper RUSLE calibration for a given situation outside the modelling community can be challenging, especially in situations outside of those widely covered in the USA. An approach pursued by Gómez et al. (2003) to overcome this problems for calibrating RUSLE, specially the cover-management factor, C, was to build a summary model using the equations defined by the RUSLE manual (Renard et al. 1997) but considering that the basic information required to calibrate the subfactors, such as soil surface roughness and ground cover, soil moisture, … were calculated (or taken from available sources) elsewhere and added to the summary model instead of calculated by the RUSLE software. This strategy simplified the calibration process as well as the understanding and interpretation of the RUSLE parameters and model behavior by on-expert users for its application in olive orchards under a broad range of management conditions. Gómez et al. (2003) build this summary model in Excel and demonstrated the ability to calibrate RUSLE for a broad range of management conditions. Later on several studies (Vanwalleghem et al., 2011, Marin, 2013) demonstrated how this summary model successfully predicted soil losses at hillslope scale close to those determined experimentally. Vines are one of the most extended tree crops covering a wide range of environmental and management conditions, and conceptually present in terms of soil conservation several analogies with olives especially in relation to soil management (Gomez et al., 2011). In vine growing areas, besides topographic and rainfall characteristics, the soil management practices

  18. Capabilities, limitations and challenges of a simplified PC-SAFT equation of state

    DEFF Research Database (Denmark)

    von Solms, Nicolas; Kouskoumvekaki, Irene; Michelsen, Michael Locht

    2006-01-01

    and physical performance of a modified PC-SAFT equation of state for highly asymmetric and associating mixtures, Ind. Eng. Chem. Res. 42 (2003) 1098.] has been applied to several complex polymer-sol vent systems, including vapor-liquid equilibria, liquid-liquid equilibria and gas solubilities for both single......-solvent and mixed-solvents (ternary) systems. This manuscript briefly reviews previous successful applications of PC-SAFT, illustrates the capabilities of the model and indicates some problems and limitations in specific areas, especially aqueous systems and blends, as well as challenges that need to be addressed...

  19. A New Distribution-Random Limit Normal Distribution

    OpenAIRE

    Gong, Xiaolin; Yang, Shuzhen

    2013-01-01

    This paper introduces a new distribution to improve tail risk modeling. Based on the classical normal distribution, we define a new distribution by a series of heat equations. Then, we use market data to verify our model.

  20. Coherent normalization of finger strontium XRF measurements: feasibility and limitations

    Energy Technology Data Exchange (ETDEWEB)

    Zamburlini, M; Pejovic-Milic, A; Chettle, D R [Medical Physics and Applied Radiation Sciences, McMaster University, Hamilton, L8S 4K1 (Canada)

    2008-08-07

    A non-invasive in vivo x-ray fluorescence (XRF) method of measuring bone strontium concentrations has previously been reported as a potential diagnostic tool able to detect strontium concentration in the finger and ankle bones. The feasibility of coherent normalization for {sup 125}I-source-based finger bone strontium x-ray fluorescence (XRF) measurements is assessed here by theoretical considerations and Monte Carlo simulations. Normalization would have several advantages, among which are the correction for the signal attenuation by the overlying soft tissue, and intersubject variability in the bone size and shape. The coherent normalization of bone strontium XRF measurements presents several challenges dictated by the behaviour of the coherent cross section and mass attenuation coefficient at the energies involved. It was found that the coherent normalization alone with either 22.1 keV or 35.5 keV photons was not successful in correcting for the overlying soft tissue attenuation. However, it was found that the coherent peak at 35.5 keV was able to correct effectively for variability in the finger bone size between people. Thus, it is suggested that, if the overlying soft tissue thickness can be obtained by means of an independent measurement, the 35.5 keV peak can be used to correct for the bone size, with an overall accuracy of the normalization process of better than 10%. (note)

  1. Sonographic assessment of the normal limits of the spleen in ...

    African Journals Online (AJOL)

    Background/Objective: Ultrasonogrphy is a good modality for the detection of splenomegaly even when it is not clinically palpable. The objective of this study was to establish the normal values of splenic length in healthy school children in South.East, Nigeria and to correlate them with body indices. Materials and Methods: ...

  2. Normalized Lift: An Energy Interpretation of the Lift Coefficient Simplifies Comparisons of the Lifting Ability of Rotating and Flapping Surfaces

    OpenAIRE

    Burgers, Phillip; Alexander, David E.

    2012-01-01

    For a century, researchers have used the standard lift coefficient C(L) to evaluate the lift, L, generated by fixed wings over an area S against dynamic pressure, ½ρv(2), where v is the effective velocity of the wing. Because the lift coefficient was developed initially for fixed wings in steady flow, its application to other lifting systems requires either simplifying assumptions or complex adjustments as is the case for flapping wings and rotating cylinders.This paper interprets the standar...

  3. Static semicoercive normal compliance contact problem with limited interpenetration

    Czech Academy of Sciences Publication Activity Database

    Jarušek, Jiří

    2015-01-01

    Roč. 66, č. 5 (2015), s. 2161-2172 ISSN 0044-2275 R&D Projects: GA ČR(CZ) GAP201/12/0671 Institutional support: RVO:67985840 Keywords : contact * limited interpenetration * friction Subject RIV: BA - General Mathematics Impact factor: 1.560, year: 2015 http://link.springer.com/article/10.1007%2Fs00033-015-0539-5

  4. Dopamine transporter imaging with [I-123]IPT SPECT in normal controls and Parkinson's patients: Feasibility study of a simplified SPECT scan protocol

    International Nuclear Information System (INIS)

    Kim, H. J.; Bong, J. K.; Nam, K. P.; Yang, S. O.; Moon, D. H.; Ryu, J. S.; Lee, H. K.

    1997-01-01

    [I-123]IPT has been used to measure changes in dopamine trasnporters with Parkinson's patients (PP). However, 2 hrs of imaging time without movement of patient's head partially limits its widespread use in routine clinical SPECT protocol. The purpose of this study was to evaluate the feasibility of a simplified IPT SPECT scan protocol using three 10 min scan data obtained at 0-10, 55-65, and 110-120 min postinjection and compared to current protocol using 23 scans obtained from O-120 min to quantify dopamine transporter binding in normal controls (NC) and PP. IPT labeled with 6.74±0.88mCi of I-123 was intravenously injected into 12 NC (age: 41±9) and 22 PP (age : 55±8) and the 5 min dynamic SPECT data were acquired for 2 hrs with Trionix triple-headed SPECT camera. SPECT images were reconstructed and attenuation corrected. [I-123] IPT quickly penetratd the blood-brain barrier and began to Ioacalize higher concentrations at the basal ganglia at 20 min after injection. The transporter parameter was measured using a variation of graphical analysis (VGA) and area ratio method (ARM) that derive the distribution volume ratios (R v =V 3 /V 2 for VGA, R A =V 3 /V 2 for ARM ) from multiple scan data without blood data, R v ' and R A ' measured from three 10 min scan data and compared with R v and R A measured from 23 scans for both NC and PP, (R v ', R v ') or NC and PP were (1.83±0.29, 2.21±0.34) and (0.63±0.34, 0.77±0.31), respectively. (R v ', R A ) for NC and PP were (1.11±0.22, 1.62±0.28) and (0.43±0.21, 0.65±0.24), respectively, Both (R v ', R v ) and (R A ', R A ) for NC were clearly separated from those for PP. R' v and R' A underestimated R v and R A by 18.4% and 33.5%, respectively, but R v ' and R A ' showed excellent correlations with R v (r=0.95) and R A (r=0.97), respectively. The results indicate that the three 10 min scan protocol may be feasible and allows us to differentiate dopamine transporter parameters in PP from those in NC

  5. Normal Limits of Electrocardiogram and Cut-Off Values for Left ...

    African Journals Online (AJOL)

    Gender difference exists in some cut-off values for LVH. This study defined the normal limits for electrocardiographic variables for young adult Nigerians. Racial factor should be taken into consideration in interpretation of ECG. Keywords: Normal limits, Electrocardiogram, Cut-off values, Left ventricular hypertrophy, Young ...

  6. Computer program determines exact two-sided tolerance limits for normal distributions

    Science.gov (United States)

    Friedman, H. A.; Webb, S. R.

    1968-01-01

    Computer program determines by numerical integration the exact statistical two-sided tolerance limits, when the proportion between the limits is at least a specified number. The program is limited to situations in which the underlying probability distribution for the population sampled is the normal distribution with unknown mean and variance.

  7. Analysis of a simplified normalized covariance measure based on binary weighting functions for predicting the intelligibility of noise-suppressed speech.

    Science.gov (United States)

    Chen, Fei; Loizou, Philipos C

    2010-12-01

    The normalized covariance measure (NCM) has been shown previously to predict reliably the intelligibility of noise-suppressed speech containing non-linear distortions. This study analyzes a simplified NCM measure that requires only a small number of bands (not necessarily contiguous) and uses simple binary (1 or 0) weighting functions. The rationale behind the use of a small number of bands is to account for the fact that the spectral information contained in contiguous or nearby bands is correlated and redundant. The modified NCM measure was evaluated with speech intelligibility scores obtained by normal-hearing listeners in 72 noisy conditions involving noise-suppressed speech corrupted by four different types of maskers (car, babble, train, and street interferences). High correlation (r = 0.8) was obtained with the modified NCM measure even when only one band was used. Further analysis revealed a masker-specific pattern of correlations when only one band was used, and bands with low correlation signified the corresponding envelopes that have been severely distorted by the noise-suppression algorithm and/or the masker. Correlation improved to r = 0.84 when only two disjoint bands (centered at 325 and 1874 Hz) were used. Even further improvements in correlation (r = 0.85) were obtained when three or four lower-frequency (<700 Hz) bands were selected.

  8. Limited value of interlaced ECG-gated radiography in the presence of a normal chest radiograph

    International Nuclear Information System (INIS)

    Chen, J.T.T.; Ravin, C.E.; Handel, D.

    1984-01-01

    Twenty-seven patients with normal posteroanterior and lateral chest radiographs, who were undergoing cardiac catheterization because of symptoms strongly suggesting coronary artery disease, also had posteroanterior and lateral interlaced electrocardiogram-gated radiographs made. In 14 patients, the interlaced radiography system underestimated (suggested hypokinesia) the wall motion, which was normal on cardiac catheterization. In two cases the system overestimated the wall motion, in two others it both under- and overestimated the motion, and in only nine cases was the correlation correct. These data suggest that the technique is of limited application, particularly in cases in which the routine chest radiographs are normal

  9. Reconstruction for limited-projection fluorescence molecular tomography based on projected restarted conjugate gradient normal residual.

    Science.gov (United States)

    Cao, Xu; Zhang, Bin; Liu, Fei; Wang, Xin; Bai, Jing

    2011-12-01

    Limited-projection fluorescence molecular tomography (FMT) can greatly reduce the acquisition time, which is suitable for resolving fast biology processes in vivo but suffers from severe ill-posedness because of the reconstruction using only limited projections. To overcome the severe ill-posedness, we report a reconstruction method based on the projected restarted conjugate gradient normal residual. The reconstruction results of two phantom experiments demonstrate that the proposed method is feasible for limited-projection FMT. © 2011 Optical Society of America

  10. Tolerance limits and tolerance intervals for ratios of normal random variables using a bootstrap calibration.

    Science.gov (United States)

    Flouri, Marilena; Zhai, Shuyan; Mathew, Thomas; Bebu, Ionut

    2017-05-01

    This paper addresses the problem of deriving one-sided tolerance limits and two-sided tolerance intervals for a ratio of two random variables that follow a bivariate normal distribution, or a lognormal/normal distribution. The methodology that is developed uses nonparametric tolerance limits based on a parametric bootstrap sample, coupled with a bootstrap calibration in order to improve accuracy. The methodology is also adopted for computing confidence limits for the median of the ratio random variable. Numerical results are reported to demonstrate the accuracy of the proposed approach. The methodology is illustrated using examples where ratio random variables are of interest: an example on the radioactivity count in reverse transcriptase assays and an example from the area of cost-effectiveness analysis in health economics. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. From explicit to implicit normal mode initialization of a limited-area model

    Energy Technology Data Exchange (ETDEWEB)

    Bijlsma, S.J.

    2013-02-15

    In this note the implicit normal mode initialization of a limited-area model is discussed from a different point of view. To that end it is shown that the equations describing the explicit normal mode initialization applied to the shallow water equations in differentiated form on the sphere can readily be derived in normal mode space if the model equations are separable, but only in the case of stationary Rossby modes can be transformed into the implicit equations in physical space. This is a consequence of the simple relations between the components of the different modes in that case. In addition a simple eigenvalue problem is given for the frequencies of the gravity waves. (orig.)

  12. Limitations in cooling electrons using normal-metal-superconductor tunnel junctions.

    Science.gov (United States)

    Pekola, J P; Heikkilä, T T; Savin, A M; Flyktman, J T; Giazotto, F; Hekking, F W J

    2004-02-06

    We demonstrate both theoretically and experimentally two limiting factors in cooling electrons using biased tunnel junctions to extract heat from a normal metal into a superconductor. First, when the injection rate of electrons exceeds the internal relaxation rate in the metal to be cooled, the electrons do not obey the Fermi-Dirac distribution, and the concept of temperature cannot be applied as such. Second, at low bath temperatures, states within the gap induce anomalous heating and yield a theoretical limit of the achievable minimum temperature.

  13. Endodontics Simplified

    OpenAIRE

    Kansal, Rohit; Talwar, Sangeeta; Yadav, Seema; Chaudhary, Sarika; Nawal, Ruchika

    2014-01-01

    The preparation of the root canal system is essential for a successful outcome in root canal treatment. The development of rotary nickel titanium instruments is considered to be an important innovation in the field of endodontics. During few last years, several new instrument systems have been introduced but the quest for simplifying the endodontic instrumentation sequence has been ongoing for almost 20 years, resulting in more than 70 different engine-driven endodontic instrumentation system...

  14. What Limits Cardiac Performance during Exercise in Normal Subjects and in Healthy Fontan Patients?

    Directory of Open Access Journals (Sweden)

    André La Gerche

    2010-01-01

    Full Text Available Exercise is an important determinant of health but is significantly reduced in the patient with a univentricular circulation. Normal exercise physiology mandates an increase in pulmonary artery pressures which places an increased work demand on the right ventricle (RV. In a biventricular circulation with pathological increases in pulmonary vascular resistance and/or reductions in RV function, exercise-induced augmentation of cardiac output is limited. Left ventricular preload reserve is dependent upon flow through the pulmonary circulation and this requires adequate RV performance. In the Fontan patient, the reasons for exercise intolerance are complex. In those patients with myocardial dysfunction or other pathologies of the circulatory components, it is likely that these abnormalities serve as a limitation to cardiac performance during exercise. However, in the healthy Fontan patient, it may be the absence of a sub-pulmonary pump which limits normal increases in pulmonary pressures, trans-pulmonary flow requirements and cardiac output. If so, performance will be exquisitely dependent on pulmonary vascular resistance. This provides a potential explanation as to why pulmonary vasodilators may improve exercise tolerance. As has recently been demonstrated, these agents may offer an important new treatment strategy which directly addresses the physiological limitations in the Fontan patient.

  15. Development of a simplified piping support system

    International Nuclear Information System (INIS)

    Leung, J.; Anderson, P.H.; Tang, Y.K.; Kassawara, R.P.; Tang, H.T.

    1987-01-01

    This paper presents the results of experimental and analytical studies for developing a simplified piping support system (SPSS) for nuclear power piping in place of snubbers. The basic concept of the SPSS is a passive seismic support system consisting of limit stops. Large gaps are provided to allow for free thermal expansion during normal plant operation while preventing excessive displacement during a seismic event. The results are part of a research and development program sponsored by EPRI. (orig./HP)

  16. Development of a simplified piping support system

    International Nuclear Information System (INIS)

    Leung, J.; Anderson, P.H.; Tang, Y.K.; Kassawara, R.P.; Tang, H.T.

    1987-01-01

    This paper presents the results of experimental and analytical studies for developing a simplified piping support system (SPSS) for nuclear power piping in place of snubbers. The basic concept of the SPSS is a passive seismic support system consisting of limit stops. Large gaps are provided to allow for free thermal expansion during normal plant operation while preventing excessive displacement during a seismic event. The results are part of a research and development program sponsored by the Electric Power Research Institute

  17. [Carbon monoxide tests in a steady state. Uptake and transfer capacity, normal values and lower limits].

    Science.gov (United States)

    Ramonatxo, M; Préfaut, C; Guerrero, H; Moutou, H; Bansard, X; Chardon, G

    1982-01-01

    The aim of this study was to establish data which would best demonstrate the variations of different tests using Carbon Monoxide as a tracer gas (total and partial functional uptake coefficient and transfer capacity) to establish mean values and lower limits of normal of these tests. Multivariate statistical analysis was used; in the first stage a connection was sought between the fractional uptake coefficient (partial and total) to other parameters, comparing subjects and data. In the second stage the comparison was refined by eliminating the least useful data, trying, despite a small loss of material, to reveal the most important connections, linear or otherwise. The fractional uptake coefficients varied according to sex, also the variation of the partial alveolar-expired fractional uptake equivalent (DuACO) was largely a function of respiratory rate and tidal volume. The alveolar-arterial partial fractional uptake equivalent (DuaCO) depended more on respiratory frequency and age. Finally the total fractional uptake coefficient (DuCO) and the transfer capacity corrected per liter of ventilation (TLCO/V) were functions of these parameters. The last stage of this work, after taking account of the statistical observations consistent with the facts of these physiological hypotheses led to a search for a better way of approaching the laws linking the collected data to the fractional uptake coefficient. The lower limits of normal were arbitrarily defined, separating those 5% of subjects deviating most strongly from the mean. As a result, the relationship between the lower limit of normal and the theoretical mean value was 90% for the partial and total fractional uptake coefficient and 70% for the transfer capacity corrected per liter of ventilation.

  18. Hanging-wall deformation above a normal fault: sequential limit analyses

    Science.gov (United States)

    Yuan, Xiaoping; Leroy, Yves M.; Maillot, Bertrand

    2015-04-01

    The deformation in the hanging wall above a segmented normal fault is analysed with the sequential limit analysis (SLA). The method combines some predictions on the dip and position of the active fault and axial surface, with geometrical evolution à la Suppe (Groshong, 1989). Two problems are considered. The first followed the prototype proposed by Patton (2005) with a pre-defined convex, segmented fault. The orientation of the upper segment of the normal fault is an unknown in the second problem. The loading in both problems consists of the retreat of the back wall and the sedimentation. This sedimentation starts from the lowest point of the topography and acts at the rate rs relative to the wall retreat rate. For the first problem, the normal fault either has a zero friction or a friction value set to 25o or 30o to fit the experimental results (Patton, 2005). In the zero friction case, a hanging wall anticline develops much like in the experiments. In the 25o friction case, slip on the upper segment is accompanied by rotation of the axial plane producing a broad shear zone rooted at the fault bend. The same observation is made in the 30o case, but without slip on the upper segment. Experimental outcomes show a behaviour in between these two latter cases. For the second problem, mechanics predicts a concave fault bend with an upper segment dip decreasing during extension. The axial surface rooting at the normal fault bend sees its dips increasing during extension resulting in a curved roll-over. Softening on the normal fault leads to a stepwise rotation responsible for strain partitioning into small blocks in the hanging wall. The rotation is due to the subsidence of the topography above the hanging wall. Sedimentation in the lowest region thus reduces the rotations. Note that these rotations predicted by mechanics are not accounted for in most geometrical approaches (Xiao and Suppe, 1992) and are observed in sand box experiments (Egholm et al., 2007, referring

  19. Normal limits of the electrocardiogram derived from a large database of Brazilian primary care patients.

    Science.gov (United States)

    Palhares, Daniel M F; Marcolino, Milena S; Santos, Thales M M; da Silva, José L P; Gomes, Paulo R; Ribeiro, Leonardo B; Macfarlane, Peter W; Ribeiro, Antonio L P

    2017-06-13

    Knowledge of the normal limits of the electrocardiogram (ECG) is mandatory for establishing which patients have abnormal ECGs. No studies have assessed the reference standards for a Latin American population. Our aim was to establish the normal ranges of the ECG for pediatric and adult Brazilian primary care patients. This retrospective observational study assessed all the consecutive 12-lead digital electrocardiograms of primary care patients at least 1 year old in Minas Gerais state, Brazil, recorded between 2010 and 2015. ECGs were excluded if there were technical problems, selected abnormalities were present or patients with selected self-declared comorbidities or on drug therapy. Only the first ECG from patients with multiple ECGs was accepted. The University of Glasgow ECG analysis program was used to automatically interpret the ECGs. For each variable, the 1st, 2nd, 50th, 98th and 99th percentiles were determined and results were compared to selected studies. A total of 1,493,905 ECGs were recorded. 1,007,891 were excluded and 486.014 were analyzed. This large study provided normal values for heart rate, P, QRS and T frontal axis, P and QRS overall duration, PR and QT overall intervals and QTc corrected by Hodges, Bazett, Fridericia and Framingham formulae. Overall, the results were similar to those from other studies performed in different populations but there were differences in extreme ages and specific measurements. This study has provided reference values for Latinos of both sexes older than 1 year. Our results are comparable to studies performed in different populations.

  20. Upper-airway flow limitation and transcutaneous carbon dioxide during sleep in normal pregnancy.

    Science.gov (United States)

    Rimpilä, Ville; Jernman, Riina; Lassila, Katariina; Uotila, Jukka; Huhtala, Heini; Mäenpää, Johanna; Polo, Olli

    2017-08-01

    Sleep during pregnancy involves a physiological challenge to provide sufficient gas exchange to the fetus. Enhanced ventilatory responses to hypercapnia and hypoxia may protect from deficient gas exchange, but sleep-disordered breathing (SDB) may predispose to adverse events. The aim of this study was to analyze sleep and breathing in healthy pregnant women compared to non-pregnant controls, with a focus on CO 2 changes and upper-airway flow limitation. Healthy women in the third trimester and healthy non-pregnant women with normal body mass index (BMI) were recruited for polysomnography. Conventional analysis of sleep and breathing was performed. Transcutaneous carbon dioxide (TcCO 2 ) was determined for each sleep stage. Flow-limitation was analyzed using the flattening index and TcCO 2 values were recorded for every inspiration. Eighteen pregnant women and 12 controls were studied. Pregnancy was associated with shorter sleep duration and more superficial sleep. Apnea-hypopnea index, arterial oxyhemoglobin desaturation, flow-limitation, snoring or periodic leg movements were similar in the two groups. Mean SaO 2 and minimum SaO 2 were lower and average heart rate was higher in the pregnant group. TcCO 2 levels did not differ between groups but variance of TcCO 2 was smaller in pregnant women during non-rapid eye movement (NREM). TcCO 2 profiles showed transient TcCO 2 peaks, which seem specific to pregnancy. Healthy pregnancy does not predispose to SDB. Enhanced ventilatory control manifests as narrowing threshold of TcCO 2 between wakefulness and sleep. Pregnant women have a tendency for rapid CO 2 increases during sleep which might have harmful consequences if not properly compensated. Copyright © 2017 Elsevier B.V. All rights reserved.

  1. Clarifying Normalization

    Science.gov (United States)

    Carpenter, Donald A.

    2008-01-01

    Confusion exists among database textbooks as to the goal of normalization as well as to which normal form a designer should aspire. This article discusses such discrepancies with the intention of simplifying normalization for both teacher and student. This author's industry and classroom experiences indicate such simplification yields quicker…

  2. Use of a simplified spectrophotometric method for quantitative determination of glucose-6-phosphate dehydrogenase activity in normal children from two day-care centers of the city of São Paulo

    Directory of Open Access Journals (Sweden)

    Roberto Muller

    2003-06-01

    Full Text Available Objective: To evaluate the applicability of a simplified method forquantitative determination of glucose-6-phosphate dehydrogenaseactivity in normal children; to determine the mean, standarddeviation and threshold value under which the enzyme activity isconsidered deficient. Methods: Blood samples were collected from201 children from two day-care centers in the city of São Paulo.The subjects were considered normal based on physicalexamination and laboratory tests. The enzyme activity wasdetermined in red blood cells of normal children using the “TestCombination G-6-PDH®” kit. The following statistical analyses werecarried out: the results were submitted to Student’s t test,Kolmogorov-Smirnov test, lower confidence interval (one-tailedtest and Spearman’s correlation coefficient. Results: The meanhemoglobin value for girls was slightly higher than the mean valuefor boys, but this difference was not statistically significant. Therewas no statistical difference in mean enzyme activities for Caucasianand non-Caucasian children. There was no significant correlation amongenzyme activity levels, red blood cells, hemoglobin levels,hematocrit, reticulocytes, white blood cells and age of patients.The mean enzyme activity for boys was 4.448 U/g Hb, standarddeviation = 1.380 U/g Hb. For girls, the mean enzyme activity was4.531 U/g Hb, standard deviation = 1.386 U/g Hb, and the differencewas not statistically significant. Therefore, the two populationgroups were considered as one single population, presenting amean enzyme activity of 4.490 U/g Hb, standard deviation = 1.380 U/g Hb.Since the distribution curve of enzyme activity values was normal,a lower confidence interval was determined (one-tailed test, witha cutoff point of 2.227 U/g Hb. Conclusion: The method used bySolem proved to be simple, fast, very accurate and useful to detectglucose-6-phosphate dehydrogenase activity and to identifychildren with enzyme deficiency.

  3. A note on asymptotic normality in the thermodynamic limit at low densities

    DEFF Research Database (Denmark)

    Jensen, J.L.

    1991-01-01

    We consider a continuous statistical mechanical system with a pair interaction in a region λ tending to infinity. For low densities asymptotic normality of the canonical statistic is proved, both in the grand canonical ensemble and in the canonical ensemble. The results are illustrated through...

  4. Conditions and limits of serum LH radioimmunoassay in normal, hypophysectomised or castred rats

    International Nuclear Information System (INIS)

    Andre, M.; Boucher, D.; Thieblot, L.

    1976-01-01

    Serum LH was measured by radioimmunoassay (NIAMD Kits) free and linked hormones were separated by double antibodies method. Influence of concentration on antibody-hormone complex is studied. Hypophysectomised rats serum does not modify results. The standard (rat LH-RPl) has the same action as serum LH. Rat serum LH contents are measured in normal or castred rats [fr

  5. Interaction between a normal shock wave and a turbulent boundary layer at high transonic speeds. Part 1: Pressure distribution. Part 2: Wall shear stress. Part 3: Simplified formulas for the prediction of surface pressures and skin friction

    Science.gov (United States)

    Adamson, T. C., Jr.; Liou, M. S.; Messiter, A. F.

    1980-01-01

    An asymptotic description is derived for the interaction between a shock wave and a turbulent boundary layer in transonic flow, for a particular limiting case. The dimensionless difference between the external flow velocity and critical sound speed is taken to be much smaller than one, but large in comparison with the dimensionless friction velocity. The basic results are derived for a flat plate, and corrections for longitudinal wall curvature and for flow in a circular pipe are also shown. Solutions are given for the wall pressure distribution and the shape of the shock wave. Solutions for the wall shear stress are obtained, and a criterion for incipient separation is derived. Simplified solutions for both the wall pressure and skin friction distributions in the interaction region are given. These results are presented in a form suitable for use in computer programs.

  6. Fourier phase analysis on equilibrium gated radionuclide ventriculography: range of phase spread and cut-off limits in normal individuals

    International Nuclear Information System (INIS)

    Ramaiah, Vijayaraghavan L.; Harish, B.; Sunil, H.V.; Selvakumar, Job; Ravi Kishore, A.G.; Nair, Gopinathan

    2011-01-01

    To define the range of phase spread on equilibrium gated radionuclide ventriculography (ERNV) in normal individuals and derive the cut-off limit for the parameters to detect cardiac dyssynchrony. ERNV was carried out in 30 individuals (age 53±23 years, 25 males and 5 females) who had no history of cardiovascular disease. They all had normal left ventricular ejection fraction (LVEF 55-70%) as determined by echocardiography, were in sinus rhythm, with normal QRS duration (≤120 msec) and normal coronary angiography. First harmonic phase analysis was performed on scintigraphic data acquired in best septal view. Left and right ventricular standard deviation (LVSD and RVSD, respectively) and interventricular mechanical delay (IVMD), the absolute difference of mean phase angles of right and left ventricle, were computed and expressed in milliseconds. Mean + 3 standard deviation (SD) was used to derive the cut-off limits. Average LVEF and duration of cardiac cycle in the study group were 62.5%±5.44% and 868.9±114.5 msec, respectively. The observations of LVSD, RVSD and right and left ventricular mean phase angles were shown to be normally distributed by Shapiro-Wilk test. Cut-off limits for LVSD, RVSD and IVMD were calculated to be 80 msec, 85 msec and 75 msec, respectively. Fourier phase analysis on ERNV is an effective tool for the evaluation of synchronicity of cardiac contraction. The cut-off limits of parameters of dyssynchrony can be used to separate heart failure patients with cardiac dyssynchrony from those without. ERNV can be used to select patients for cardiac resynchronization therapy. (author)

  7. On computation of limiting coderivatives of the normal-cone mapping to inequality systems and their applications

    Czech Academy of Sciences Publication Activity Database

    Outrata, Jiří; Gfrerer, H.

    2016-01-01

    Roč. 65, č. 4 (2016), s. 671-700 ISSN 0233-1934 R&D Projects: GA ČR GAP402/12/1309 Institutional support: RVO:67985556 Keywords : limiting normal cone * metric regularity and subregularity * parameterized generalized equations Subject RIV: BA - General Mathematics Impact factor: 0.943, year: 2016 http://library.utia.cas.cz/separaty/2015/MTR/outrata-0447466.pdf

  8. Tracheal sound parameters of respiratory cycle phases show differences between flow-limited and normal breathing during sleep

    International Nuclear Information System (INIS)

    Kulkas, A; Huupponen, E; Virkkala, J; Saastamoinen, A; Rauhala, E; Tenhunen, M; Himanen, S-L

    2010-01-01

    The objective of the present work was to develop new computational parameters to examine the characteristics of respiratory cycle phases from the tracheal breathing sound signal during sleep. Tracheal sound data from 14 patients (10 males and 4 females) were examined. From each patient, a 10 min long section of normal and a 10 min section of flow-limited breathing during sleep were analysed. The computationally determined proportional durations of the respiratory phases were first investigated. Moreover, the phase durations and breathing sound amplitude levels were used to calculate the area under the breathing sound envelope signal during inspiration and expiration phases. An inspiratory sound index was then developed to provide the percentage of this type of area during the inspiratory phase with respect to the combined area of inspiratory and expiratory phases. The proportional duration of the inspiratory phase showed statistically significantly higher values during flow-limited breathing than during normal breathing and inspiratory pause displayed an opposite difference. The inspiratory sound index showed statistically significantly higher values during flow-limited breathing than during normal breathing. The presented novel computational parameters could contribute to the examination of sleep-disordered breathing or as a screening tool

  9. Envelhecimento cerebral: o problema dos limites entre o normal e o patológico Brain ageing: problems of differential diagnosis between normal and pathologic

    Directory of Open Access Journals (Sweden)

    BENITO PEREIRA DAMASCENO

    1999-03-01

    Full Text Available O autor relata três casos de pseudodemência e discute o problema dos limites entre o normal e o patológico no sujeito idoso. O envelhecimento cerebral acompanha-se de alterações mentais e neuropatológicas superponíveis às da demência de Alzheimer (DA, levando a problemas de diagnóstico diferencial. Ainda não existe um marcador biológico seguro de DA e os testes psicométricos podem dar resultados falso-positivos ou falso-negativos. No idoso normal, o declínio da memória operacional e memória secundária é maior que o das memórias primária e terciária, de modo similar ao encontrado nas fases iniciais da DA. Os testes de evocação retardada de lista de palavras, memória lógica, pensamento categórico, destreza visuo-motora-espacial e o Teste de Nomeação de Boston têm sido apontados como os mais discriminativos entre demência incipiente e normalidade. Na neuroimagem, os achados de atrofia ou hipoperfusão em regiões entorrinais-hipocampais ou temporo-parietais são sugestivos de DA, mas podem estar ausentes nas fases iniciais desta doença. O autor conclui sugerindo passos decisivos para o diagnóstico diferencial: avaliação neuropsicológica e comportamental abrangente (com levantamento do nível pré-mórbido de funcionamento cognitivo e sócio-ocupacional do paciente, bem como exames laboratoriais e de neuroimagem; e, se preciso, reavaliação após 4 a 6 meses, para verificar a consistência dos achados.The author reports three cases of pseudodementia and discuss the difficulties in establishing limits between normality and illness in the elderly. The mental and neuropathological changes that accompany the normal ageing of the brain are similar to those of early Alzheimer's dementia (AD. These similarities often lead to difficulties in the differential diagnosis, hence the search for consensus criteria. The decline of working and secondary memory is greater than that of primary and tertiary memory, as is found in AD

  10. The effects of limited bandwidth and noise on verbal processing time and word recall in normal-hearing children.

    Science.gov (United States)

    McCreery, Ryan W; Stelmachowicz, Patricia G

    2013-09-01

    Understanding speech in acoustically degraded environments can place significant cognitive demands on school-age children who are developing the cognitive and linguistic skills needed to support this process. Previous studies suggest the speech understanding, word learning, and academic performance can be negatively impacted by background noise, but the effect of limited audibility on cognitive processes in children has not been directly studied. The aim of the present study was to evaluate the impact of limited audibility on speech understanding and working memory tasks in school-age children with normal hearing. Seventeen children with normal hearing between 6 and 12 years of age participated in the present study. Repetition of nonword consonant-vowel-consonant stimuli was measured under conditions with combinations of two different signal to noise ratios (SNRs; 3 and 9 dB) and two low-pass filter settings (3.2 and 5.6 kHz). Verbal processing time was calculated based on the time from the onset of the stimulus to the onset of the child's response. Monosyllabic word repetition and recall were also measured in conditions with a full bandwidth and 5.6 kHz low-pass cutoff. Nonword repetition scores decreased as audibility decreased. Verbal processing time increased as audibility decreased, consistent with predictions based on increased listening effort. Although monosyllabic word repetition did not vary between the full bandwidth and 5.6 kHz low-pass filter condition, recall was significantly poorer in the condition with limited bandwidth (low pass at 5.6 kHz). Age and expressive language scores predicted performance on word recall tasks, but did not predict nonword repetition accuracy or verbal processing time. Decreased audibility was associated with reduced accuracy for nonword repetition and increased verbal processing time in children with normal hearing. Deficits in free recall were observed even under conditions where word repetition was not affected

  11. New limits on the population of normal and millisecond pulsars in the Large and Small Magellanic Clouds

    Science.gov (United States)

    Ridley, J. P.; Lorimer, D. R.

    2010-07-01

    We model the potentially observable populations of normal and millisecond radio pulsars in the Large and Small Magellanic Clouds (LMC and SMC, respectively) where the known population currently stands at 19 normal radio pulsars. Taking into account the detection thresholds of previous surveys, and assuming optimal period and luminosity distributions based on studies of Galactic pulsars, we estimate that there are (1.79 +/- 0.20) × 104 and (1.09 +/- 0.16) × 104 normal pulsars in the LMC and SMC, respectively. When we attempt to correct for beaming effects, and the fraction of high-velocity pulsars which escape the clouds, we estimate birth rates in both the LMC and SMC to be comparable and in the range of 0.5-1 pulsars per century. Although higher than estimates for the rate of core-collapse supernovae in the clouds, these pulsar birth rates are consistent with historical supernova observations in the past 300 yr. A substantial population of active radio pulsars (of the order of a few hundred thousand) has escaped the LMC and SMC and populates the local intergalactic medium. For the millisecond pulsar (MSP) population, the lack of any detections from current surveys leads to respective upper limits (at the 95 per cent confidence level) of 15000 for the LMC and 23000 for the SMC. Several MSPs could be detected by a currently ongoing survey of the SMC with improved time and frequency resolution using the Parkes multibeam system. Giant-pulse emitting neutron stars could also be seen by this survey.

  12. Autoblocking dose-limiting normal structures within a radiation treatment field: 3-D computer optimization of 'unconventional' field arrangements

    International Nuclear Information System (INIS)

    Bates, Brian A.; Cullip, Timothy J.; Rosenman, Julian G.

    1995-01-01

    Purpose/Objective: To demonstrate that one can obtain a homogeneous dose distribution within a specified gross tumor volume (GTV) while severely limiting the dose to a structure surrounded by that tumor volume. We present three clinical examples below. Materials and Methods: Using planning CT scans from previously treated patients, we designed variety of radiation treatment plans in which the dose-critical normal structure was blocked, even if it meant blocking some of the tumor. To deal with the resulting dose inhomogeneities within the tumor, we introduced 3D compensation. Examples presented here include (1) blocking the spinal cord segment while treating an entire vertebral body, (2) blocking both kidneys while treating the entire peritoneal cavity, and (3) blocking one parotid gland while treating the oropharynx in its entirety along with regional nodes. A series of multiple planar and non-coplanar beam templates with automatic anatomic blocking and field shaping were designed for each scenario. Three-dimensional compensators were designed that gave the most homogeneous dose-distribution for the GTV. For each beam, rays were cast from the beam source through a 2D compensator grid and out through the tumor. The average tumor dose along each ray was then used to adjust the compensator thickness over successive iterations to achieve a uniform average dose. DVH calculations for the GTV, normal structures, and the 'auto-blocked' structure were made and used for inter-plan comparisons. Results: These optimized treatment plans successfully decreased dose to the dose-limiting structure while at the same time preserving or even improving the dose distribution to the tumor volume as compared to traditional treatment plans. Conclusion: The use of 3D compensation allows one to obtain dose distributions that are, theoretically, at least, far superior to those in common clinical use. Sensible beam templates, auto-blocking, auto-field shaping, and 3D compensators form a

  13. 3.6 simplified methods for design

    International Nuclear Information System (INIS)

    Nickell, R.E.; Yahr, G.T.

    1981-01-01

    Simplified design analysis methods for elevated temperature construction are classified and reviewed. Because the major impetus for developing elevated temperature design methodology during the past ten years has been the LMFBR program, considerable emphasis is placed upon results from this source. The operating characteristics of the LMFBR are such that cycles of severe transient thermal stresses can be interspersed with normal elevated temperature operational periods of significant duration, leading to a combination of plastic and creep deformation. The various simplified methods are organized into two general categories, depending upon whether it is the material, or constitutive, model that is reduced, or the geometric modeling that is simplified. Because the elastic representation of material behavior is so prevalent, an entire section is devoted to elastic analysis methods. Finally, the validation of the simplified procedures is discussed

  14. Simplified Dark Matter Models

    OpenAIRE

    Morgante, Enrico

    2018-01-01

    I review the construction of Simplified Models for Dark Matter searches. After discussing the philosophy and some simple examples, I turn the attention to the aspect of the theoretical consistency and to the implications of the necessary extensions of these models.

  15. Simplified pipe gun

    International Nuclear Information System (INIS)

    Sorensen, H.; Nordskov, A.; Sass, B.; Visler, T.

    1987-01-01

    A simplified version of a deuterium pellet gun based on the pipe gun principle is described. The pipe gun is made from a continuous tube of stainless steel and gas is fed in from the muzzle end only. It is indicated that the pellet length is determined by the temperature gradient along the barrel right outside the freezing cell. Velocities of around 1000 m/s with a scatter of +- 2% are obtained with a propellant gas pressure of 40 bar

  16. UTILITY OF SIMPLIFIED LABANOTATION

    Directory of Open Access Journals (Sweden)

    Maria del Pilar Naranjo

    2016-02-01

    Full Text Available After using simplified Labanotation as a didactic tool for some years, the author can conclude that it accomplishes at least three main functions: efficiency of rehearsing time, social recognition and broadening of the choreographic consciousness of the dancer. The doubts of the dancing community about the issue of ‘to write or not to write’ are highly determined by the contexts and their own choreographic evolution, but the utility of Labanotation, as a tool for knowledge, is undeniable.

  17. Windows 8 simplified

    CERN Document Server

    McFedries, Paul

    2012-01-01

    The easiest way for visual learners to get started with Windows 8 The popular Simplified series makes visual learning easier than ever, and with more than 360,000 copies sold, previous Windows editions are among the bestselling Visual books. This guide goes straight to the point with easy-to-follow, two-page tutorials for each task. With full-color screen shots and step-by-step directions, it gets beginners up and running on the newest version of Windows right away. Learn to work with the new interface and improved Internet Explorer, manage files, share your computer, and much more. Perfect fo

  18. Office 2013 simplified

    CERN Document Server

    Marmel, Elaine

    2013-01-01

    A basic introduction to learn Office 2013 quickly, easily, and in full color Office 2013 has new features and tools to master, and whether you're upgrading from an earlier version or using the Office applications for the first time, you'll appreciate this simplified approach. Offering a clear, visual style of learning, this book provides you with concise, step-by-step instructions and full-color screen shots that walk you through the applications in the Microsoft Office 2013 suite: Word, Excel, PowerPoint, Outlook, and Publisher.Shows you how to tackle dozens of Office 2013

  19. Windows 10 simplified

    CERN Document Server

    McFedries, Paul

    2015-01-01

    Learn Windows 10 quickly and painlessly with this beginner's guide Windows 10 Simplified is your absolute beginner's guide to the ins and outs of Windows. Fully updated to cover Windows 10, this highly visual guide covers all the new features in addition to the basics, giving you a one-stop resource for complete Windows 10 mastery. Every page features step-by-step screen shots and plain-English instructions that walk you through everything you need to know, no matter how new you are to Windows. You'll master the basics as you learn how to navigate the user interface, work with files, create

  20. Simplifying massive planar subdivisions

    DEFF Research Database (Denmark)

    Arge, Lars; Truelsen, Jakob; Yang, Jungwoo

    2014-01-01

    We present the first I/O- and practically-efficient algorithm for simplifying a planar subdivision, such that no point is moved more than a given distance εxy and such that neighbor relations between faces (homotopy) are preserved. Under some practically realistic assumptions, our algorithm uses ....... For example, for the contour map simplification problem it is significantly faster than the previous algorithm, while obtaining approximately the same simplification factor. Read More: http://epubs.siam.org/doi/abs/10.1137/1.9781611973198.3...

  1. Creating Web Pages Simplified

    CERN Document Server

    Wooldridge, Mike

    2011-01-01

    The easiest way to learn how to create a Web page for your family or organization Do you want to share photos and family lore with relatives far away? Have you been put in charge of communication for your neighborhood group or nonprofit organization? A Web page is the way to get the word out, and Creating Web Pages Simplified offers an easy, visual way to learn how to build one. Full-color illustrations and concise instructions take you through all phases of Web publishing, from laying out and formatting text to enlivening pages with graphics and animation. This easy-to-follow visual guide sho

  2. Simplified elastoplastic fatigue analysis

    International Nuclear Information System (INIS)

    Autrusson, B.; Acker, D.; Hoffmann, A.

    1987-01-01

    Oligocyclic fatigue behaviour is a function of the local strain range. The design codes ASME section III, RCC-M, Code Case N47, RCC-MR, and the Guide issued by PNC propose simplified methods to evaluate the local strain range. After having briefly described these simplified methods, we tested them by comparing the results of experimental strains with those predicted by these rules. The experiments conducted for this study involved perforated plates under tensile stress, notched or reinforced beams under four-point bending stress, grooved specimens under tensile-compressive stress, and embedded grooved beams under bending stress. They display a relative conservatism depending on each case. The evaluation of the strains of rather inaccurate and sometimes lacks conservatism. So far, the proposal is to use the finite element codes with a simple model. The isotropic model with the cyclic consolidation curve offers a good representation of the real equivalent strain. There is obviously no question of representing the cycles and the entire loading history, but merely of calculating the maximum variation in elastoplastic equivalent deformations with a constant-rate loading. The results presented testify to the good prediction of the strains with this model. The maximum equivalent strain will be employed to evaluate fatigue damage

  3. Simplified proceeding as a civil procedure model

    Directory of Open Access Journals (Sweden)

    Олексій Юрійович Зуб

    2016-01-01

    Full Text Available Currently the directions for the development of modern civil procedural law such as optimization, facilitation, forwarding proceedings promoting the increase of the civil procedure efficiency factor are of peculiar importance. Their results are occurrence and functionality of simplified proceedings system designed to facilitate significantly hearing some categories of cases, promotion of their consideration within reasonable time and reduce legal expenses so far as it is possible. The category “simplified proceedings” in the native science of the procedural law is underexamined. A good deal of scientists-processualists were limited to studying summary (in the context of optimization as a way to improve the civil procedural form, summary proceedings and procedures functioning in terms of the mentioned proceedings, consideration of case in absentia as well as their modification. Among the Ukrainian scientist who studied some aspects of the simplified proceedings are: E. A. Belyanevych, V. I. Bobrik, S. V. Vasilyev, M. V. Verbitska, S. I. Zapara, A. A. Zgama, V. V. Komarov, D. D. Luspenuk, U. V. Navrotska, V. V. Protsenko, T. V. Stepanova, E. A. Talukin, S. Y. Fursa, M. Y. Shtefan others. The problems of the simplified proceedings were studied by the foreign scientists as well, such as: N. Andrews, Y. Y. Grubanon, N. A. Gromoshina, E. P. Kochanenko, J. Kohler, D. I. Krumskiy, E. M. Muradjan, I. V. Reshetnikova, U. Seidel, N. V. Sivak, M. Z. Shvarts, V. V. Yarkov and others. The paper objective is to develop theoretically supported, practically reasonable notion of simplified proceedings in the civil process, and also basing on the notion of simplified proceedings, international experience of the legislative regulation of simplified proceedings, native and foreign doctrine, to distinguish essential features of simplified proceedings in the civil process and to describe them. In the paper we generated the notion of simplified proceedings that

  4. Derived release limits (DRL's) for airborne and liquid effluents from the Chalk River Nuclear Laboratories during normal operations

    International Nuclear Information System (INIS)

    Palmer, J.F.

    1981-02-01

    Derived release limits (DRL's), based on regulatory dose limits, have been calculated for routine discharges of radioactivity in airborne and liquid effluents from the Chalk River Nuclear Laboratories. Three types of sources of airborne effluents were considered: the NRX/NRU stack, the 61 m stack connected to the 99 Mo production facility, and a roof vent typical of those installed on several buildings on the site. Sources of liquid effluents to the Ottawa River were treated as a single source from the site as a whole. Various exposure pathways to workers on the site and to members of the public outside the site boundary were considered in the calculations. The DRL's represent upper limits for routine emissions of radioactivity from the Chalk River Nuclear Laboratories to the surrounding environment. Actual releases are regulated by Administrative Levels, set lower than the DRL's, and are confirmed by monitoring. (author)

  5. Combination of exercise training and diet restriction normalizes limited exercise capacity and impaired skeletal muscle function in diet-induced diabetic mice.

    Science.gov (United States)

    Suga, Tadashi; Kinugawa, Shintaro; Takada, Shingo; Kadoguchi, Tomoyasu; Fukushima, Arata; Homma, Tsuneaki; Masaki, Yoshihiro; Furihata, Takaaki; Takahashi, Masashige; Sobirin, Mochamad A; Ono, Taisuke; Hirabayashi, Kagami; Yokota, Takashi; Tanaka, Shinya; Okita, Koichi; Tsutsui, Hiroyuki

    2014-01-01

    Exercise training (EX) and diet restriction (DR) are essential for effective management of obesity and insulin resistance in diabetes mellitus. However, whether these interventions ameliorate the limited exercise capacity and impaired skeletal muscle function in diabetes patients remains unexplored. Therefore, we investigated the effects of EX and/or DR on exercise capacity and skeletal muscle function in diet-induced diabetic mice. Male C57BL/6J mice that were fed a high-fat diet (HFD) for 8 weeks were randomly assigned for an additional 4 weeks to 4 groups: control, EX, DR, and EX+DR. A lean group fed with a normal diet was also studied. Obesity and insulin resistance induced by a HFD were significantly but partially improved by EX or DR and completely reversed by EX+DR. Although exercise capacity decreased significantly with HFD compared with normal diet, it partially improved with EX and DR and completely reversed with EX+DR. In parallel, the impaired mitochondrial function and enhanced oxidative stress in the skeletal muscle caused by the HFD were normalized only by EX+DR. Although obesity and insulin resistance were completely reversed by DR with an insulin-sensitizing drug or a long-term intervention, the exercise capacity and skeletal muscle function could not be normalized. Therefore, improvement in impaired skeletal muscle function, rather than obesity and insulin resistance, may be an important therapeutic target for normalization of the limited exercise capacity in diabetes. In conclusion, a comprehensive lifestyle therapy of exercise and diet normalizes the limited exercise capacity and impaired muscle function in diabetes mellitus.

  6. Simplified tritium permeation model

    International Nuclear Information System (INIS)

    Longhurst, G.R.

    1993-01-01

    In this model I seek to provide a simplified approach to solving permeation problems addressed by TMAP4. I will assume that there are m one-dimensional segments with thickness L i , i = 1, 2, hor-ellipsis, m, joined in series with an implantation flux, J i , implanting at the single depth, δ, in the first segment. From material properties and heat transfer considerations, I calculate temperatures at each face of each segment, and from those temperatures I find local diffusivities and solubilities. I assume recombination coefficients K r1 and K r2 are known at the upstream and downstream faces, respectively, but the model will generate Baskes recombination coefficient values on demand. Here I first develop the steady-state concentration equations and then show how trapping considerations can lead to good estimates of permeation transient times

  7. Simplifying EU environmental legislation

    DEFF Research Database (Denmark)

    Anker, Helle Tegner

    2014-01-01

    The recent review of the EIA Directive was launched as part of the ‘better regulation’ agenda with the purpose to simplify procedures and reduce administrative burdens. This was combined with an attempt to further harmonise procedures in order address shortcomings in the Directive and to overcome...... for different interpretations on core issues. This is likely to result in diverging practices in the Member States as well as in further litigation on EIA matters. It is argued that at least from the outset the review of the EIA Directive missed out on a more thorough discussion of fundamental issues linked...... to the character and scope of EIA such as the important distinction between the procedural functions of information gathering and participation as opposed to the substantive outcomes in terms of reducing or avoiding adverse effects. A careful discussion of the basics of EIA might have provided a better option...

  8. Conceptual design of simplified PWR

    International Nuclear Information System (INIS)

    Tabata, Hiroaki

    1996-01-01

    The limited availability for location of nuclear power plant in Japan makes plants with higher power ratings more desirable. Having no intention of constructing medium-sized plants as a next generation standard plant, Japanese utilities are interested in applying passive technologies to large ones. So, Japanese utilities have studied large passive plants based on AP600 and SBWR as alternative future LWRs. In a joint effort to develop a new generation nuclear power plant which is more friendly to operator and maintenance personnel and is economically competitive with alternative sources of power generation, JAPC and Japanese Utilities started the study to modify AP600 and SBWR, in order to accommodate the Japanese requirements. During a six year program up to 1994, basic concepts for 1000 MWe class Simplified PWR (SPWR) and Simplified BWR (SBWR) were developed, though there still remain several areas to be improved. These studies have now stepped into the phase of reducing construction cost and searching for maximum power rating that can be attained by reasonably practical technology. These results also suggest that it is hopeful to develop a large 3-loop passive plant (∼1200 MWe). Since Korea mainly deals with PWR, this paper summarizes SPWR study. The SPWR is jointly studied by JAPC, Japanese PWR Utilities, EdF, WH and Mitsubishi Heavy Industry. Using the AP-600 reference design as a basis, we enlarged the plant size to 3-loops and added engineering features to conform with Japanese practice and Utilities' preference. The SPWR program definitively confirmed the feasibility of a passive plant with an NSSS rating about 1000 MWe and 3 loops. (J.P.N.)

  9. "I thought this course was going to be streamlined!": the limits of normal and the possibilities of transgression.

    Science.gov (United States)

    Simpson, Jennifer S

    2012-01-01

    This article offers an analysis of the parallels between neo-liberalism, epistemology, and pedagogy, specifically related to how neoliberal ideologies narrow the possibilities for considering transgressive sexualities. Lesbian, gay, bisexual, transgender, and queer (LGBTQ) education encourages educators to consider queer lives and communities, and can do so in ways that leave intact or challenge dominant norms. Neoliberalism, an economic expression of liberalism, rests on ideologies that support privatization and a diminished notion of the public good. These ideologies can become intertwined with epistemological expectations in the classroom. Related to queer theory and pedagogy, neoliberalism can profoundly narrow the possibilities for queer subjecthood. Epistemological neoliberalism, or structures of knowing that endorse an often falsely rendered normality, can be active in the classroom. This article explores two comments students offered in courses on gender and communication to explore the ways in which neoliberal ideologies bear on epistemological and pedagogical practices in ways that profoundly narrow conceptions of the social and constitutions of the subject, particularly related to transgressive sexualities and queer lives.

  10. The simplified models approach to constraining supersymmetry

    Energy Technology Data Exchange (ETDEWEB)

    Perez, Genessis [Institut fuer Theoretische Physik, Karlsruher Institut fuer Technologie (KIT), Wolfgang-Gaede-Str. 1, 76131 Karlsruhe (Germany); Kulkarni, Suchita [Laboratoire de Physique Subatomique et de Cosmologie, Universite Grenoble Alpes, CNRS IN2P3, 53 Avenue des Martyrs, 38026 Grenoble (France)

    2015-07-01

    The interpretation of the experimental results at the LHC are model dependent, which implies that the searches provide limited constraints on scenarios such as supersymmetry (SUSY). The Simplified Models Spectra (SMS) framework used by ATLAS and CMS collaborations is useful to overcome this limitation. SMS framework involves a small number of parameters (all the properties are reduced to the mass spectrum, the production cross section and the branching ratio) and hence is more generic than presenting results in terms of soft parameters. In our work, the SMS framework was used to test Natural SUSY (NSUSY) scenario. To accomplish this task, two automated tools (SModelS and Fastlim) were used to decompose the NSUSY parameter space in terms of simplified models and confront the theoretical predictions against the experimental results. The achievement of both, just as the strengths and limitations, are here expressed for the NSUSY scenario.

  11. Cosmological helium production simplified

    International Nuclear Information System (INIS)

    Bernstein, J.; Brown, L.S.; Feinberg, G.

    1988-01-01

    We present a simplified model of helium synthesis in the early universe. The purpose of the model is to explain clearly the physical ideas relevant to the cosmological helium synthesis, in a manner that does not overlay these ideas with complex computer calculations. The model closely follows the standard calculation, except that it neglects the small effect of Fermi-Dirac statistics for the leptons. We also neglect the temperature difference between photons and neutrinos during the period in which neutrons and protons interconvert. These approximations allow us to express the neutron-proton conversion rates in a closed form, which agrees to 10% accuracy or better with the exact rates. Using these analytic expressions for the rates, we reduce the calculation of the neutron-proton ratio as a function of temperature to a simple numerical integral. We also estimate the effect of neutron decay on the helium abundance. Our result for this quantity agrees well with precise computer calculations. We use our semi-analytic formulas to determine how the predicted helium abundance varies with such parameters as the neutron life-time, the baryon to photon ratio, the number of neutrino species, and a possible electron-neutrino chemical potential. 19 refs., 1 fig., 1 tab

  12. Unravelling the escape dynamics and the nature of the normally hyperbolic invariant manifolds in tidally limited star clusters

    Science.gov (United States)

    Zotos, Euaggelos E.; Jung, Christof

    2017-02-01

    The escape mechanism of orbits in a star cluster rotating around its parent galaxy in a circular orbit is investigated. A three degrees of freedom model is used for describing the dynamical properties of the Hamiltonian system. The gravitational field of the star cluster is represented by a smooth and spherically symmetric Plummer potential. We distinguish between ordered and chaotic orbits as well as between trapped and escaping orbits, considering only unbounded motion for several energy levels. The Smaller ALignment Index (SALI) method is used for determining the regular or chaotic nature of the orbits. The basins of escape are located and they are also correlated with the corresponding escape time of the orbits. Areas of bounded regular or chaotic motion and basins of escape were found to coexist in the (x, z) plane. The properties of the normally hyperbolic invariant manifolds (NHIMs), located in the vicinity of the index-1 Lagrange points L1 and L2, are also explored. These manifolds are of paramount importance as they control the flow of stars over the saddle points, while they also trigger the formation of tidal tails observed in star clusters. Bifurcation diagrams of the Lyapunov periodic orbits as well as restrictions of the Poincaré map to the NHIMs are deployed for elucidating the dynamics in the neighbourhood of the saddle points. The extended tidal tails, or tidal arms, formed by stars with low velocity which escape through the Lagrange points are monitored. The numerical results of this work are also compared with previous related work.

  13. Mammalian Cell Culture Simplified.

    Science.gov (United States)

    Moss, Robert; Solomon, Sondra

    1991-01-01

    A tissue culture experiment that does not require elaborate equipment and that can be used to teach sterile technique, the principles of animal cell line maintenance, and the concept of cell growth curves is described. The differences between cancerous and normal cells can be highlighted. The procedure is included. (KR)

  14. New age- and sex-specific criteria for QT prolongation based on rate correction formulas that minimize bias at the upper normal limits.

    Science.gov (United States)

    Rautaharju, Pentti M; Mason, Jay W; Akiyama, Toshio

    2014-07-01

    Existing formulas for rate-corrected QT (QTc) commonly fail to properly adjust the upper normal limits which are more critical than the mean QTc for evaluation of prolonged QT. Age- and sex-related differences in QTc are also often overlooked. Our goal was to establish criteria for prolonged QTc using formulas that minimize QTc bias at the upper normal limits. Strict criteria were used in selecting a study group of 57,595 persons aged 5 to 89 years (54% women) and to exclude electrocardiograms (ECG) with possible disease-associated changes. Two QT rate adjustment formulas were identified which both minimized rate-dependency in the 98 th percentile limits: QTcmod, based on an electrophysiological model (QTcMod = QTx(120 + HR)/180)), and QTcLogLin, a power function of the RR interval with exponents 0.37 for men and 0.38 for women. QTc shortened in men during adolescence and QTcMod became 13 ms shorter than in women at age 20-29 years. The sex difference was maintained through adulthood although decreasing with age. The criteria established for prolonged QTc were: Age < 40 years, men 430 ms, women 440 ms; Age 40 to 69, men 440 ms, women 450 ms; Age ≥ 70 years, men 455 ms, and women 460 ms. Sex difference in QTc originates from shortened QT in adolescent males. Upper normal limits for QTc vary substantially by age and sex, and it is essential to use age- and sex-specific criteria for evaluation of QT prolongation. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  15. An assessment of racial differences in the upper limits of normal ALT levels in children and the effect of obesity on elevated values.

    Science.gov (United States)

    Kliethermes, S; Ma, M; Purtell, C; Balasubramanian, N; Gonzalez, B; Layden, T J; Cotler, S J

    2017-10-01

    Childhood obesity is a risk factor for non-alcoholic fatty liver disease and poses important public health issues for children. Racial differences in alanine aminotransferase (ALT) levels among children have not been described. This study aimed to identify racial differences in upper limit normal (ULN) ALT levels and evaluate the effect of obesity on elevated levels in children without other metabolic risk factors. National Health and Nutrition Examination Surveys and clinical data from the Loyola University Health System were used to determine ULN ALT by race and gender. Quantile regression was used to evaluate the impact of obesity on elevated ALT and to identify potential risk factors for ALT above the ULN. Upper limit normal (ULN) ALT was approximately 28.0 and 21.0-24.0 U/L for boys and girls, respectively. No significant difference in ULN ALT across race was observed. Obesity was significantly associated with elevated ALT; obese children with elevated ALT had values 10 U/L higher than normal-weight children. Racial differences in ALT levels among adults are not evident in children. Obesity, in the absence of metabolic risk factors and other causes of liver disease, is associated with elevated ALT, providing evidence against the concept of healthy obesity in children. © 2016 World Obesity Federation.

  16. Simplified Multimodal Biometric Identification

    Directory of Open Access Journals (Sweden)

    Abhijit Shete

    2014-03-01

    Full Text Available Multibiometric systems are expected to be more reliable than unimodal biometric systems for personal identification due to the presence of multiple, fairly independent pieces of evidence e.g. Unique Identification Project "Aadhaar" of Government of India. In this paper, we present a novel wavelet based technique to perform fusion at the feature level and score level by considering two biometric modalities, face and fingerprint. The results indicate that the proposed technique can lead to substantial improvement in multimodal matching performance. The proposed technique is simple because of no preprocessing of raw biometric traits as well as no feature and score normalization.

  17. On the simplified path integral on spheres

    Energy Technology Data Exchange (ETDEWEB)

    Bastianelli, Fiorenzo [Universita di Bologna, Dipartimento di Fisica ed Astronomia, Bologna (Italy); INFN, Sezione di Bologna, Bologna (Italy); Albert-Einstein-Institut, Max-Planck-Institut fuer Gravitationsphysik, Golm (Germany); Corradini, Olindo [Universita degli Studi di Modena e Reggio Emilia, Dipartimento di Scienze Fisiche, Informatiche e Matematiche, Modena (Italy); INFN, Sezione di Bologna, Bologna (Italy); Albert-Einstein-Institut, Max-Planck-Institut fuer Gravitationsphysik, Golm (Germany)

    2017-11-15

    We have recently studied a simplified version of the path integral for a particle on a sphere, and more generally on maximally symmetric spaces, and proved that Riemann normal coordinates allow the use of a quadratic kinetic term in the particle action. The emerging linear sigma model contains a scalar effective potential that reproduces the effects of the curvature. We present here further details of the construction, and extend its perturbative evaluation to orders high enough to read off the type-A trace anomalies of a conformal scalar in dimensions d = 14 and d = 16. (orig.)

  18. Analysis of semen parameters in male referrals: impact of reference limits, stratification by fertility categories, predictors of change, and comparison of normal semen parameters in subfertile couples.

    Science.gov (United States)

    Baker, Karen; Li, Jianbo; Sabanegh, Edmund

    2015-01-01

    To [1] determine the impact of semen reference limits on referrals for male fertility evaluations, [2] analyze the stratification of subjects based on published "normal" thresholds, [3] analyze the odds of changing fertility categories during serial tests and thereby the potential impact of inherent variability of semen parameters on referrals, and [4] determine variable(s) predictive of change. Retrospective chart review. Academic referral center for male fertility. New encounters in a male fertility clinic over a 5-year period that straddles the publication of World Health Organization (WHO) 2010 reference values. None. Demographic and clinical variables, semen values, and fertility categories as follows: BE (below WHO 2010 criteria), BTWN (above WHO 2010 but below WHO 1999 criteria), and N (above WHO 1999 criteria). A total of 82.3% of initial semen tests were categorized as BE, and the predominance of this category was unchanged by publication of the WHO 2010 criteria. Men with initial semen analysis categorized as BTWN or N represented 16.2% and 1.5% of the referral population, respectively. Subjects initially categorized as BTWN were more likely to change fertility categories, and overwhelmingly this migration was downward. Analysis of normal individual semen parameters revealed statistically worse mean concentration and motility when at least one other parameter fell below the WHO 2010 criteria. Men with semen results above reference criteria are underrepresented, indicating that reference limits influence referral patterns for male fertility evaluations. Normal mean concentration and motility were lower in men with at least one other individual semen parameter below the 2010 criteria, suggesting global dysfunction in spermatogenesis. Published by Elsevier Inc.

  19. Digital security technology simplified.

    Science.gov (United States)

    Scaglione, Bernard J

    2007-01-01

    Digital security technology is making great strides in replacing analog and other traditional security systems including CCTV card access, personal identification and alarm monitoring applications. Like any new technology, the author says, it is important to understand its benefits and limitations before purchasing and installing, to ensure its proper operation and effectiveness. This article is a primer for security directors on how digital technology works. It provides an understanding of the key components which make up the foundation for digital security systems, focusing on three key aspects of the digital security world: the security network, IP cameras and IP recorders.

  20. A simplified four-unknown shear and normal deformation theory

    Indian Academy of Sciences (India)

    The in-plane longitudinal stress ¯σ1 versus the side-to-thickness ratio a/h of a ..... in which Ei are Young's moduli in the material principal directions, vij are Poisson's ratios, ..... drical shells integrated with piezoelectric fiber reinforced composite ...

  1. A simplified quantum gravitational model of inflation

    International Nuclear Information System (INIS)

    Tsamis, N C; Woodard, R P

    2009-01-01

    Inflationary quantum gravity simplifies drastically in the leading logarithm approximation. We show that the only counterterm which contributes in this limit is the 1-loop renormalization of the cosmological constant. We go further to make a simplifying assumption about the operator dynamics at leading logarithm order. This assumption is explicitly implemented at 1- and 2-loop orders, and we describe how it can be implemented nonperturbatively. We also compute the expectation value of an invariant observable designed to quantify the quantum gravitational back-reaction on inflation. Although our dynamical assumption may not prove to be completely correct, it does have the right time dependence, it can naturally produce primordial perturbations of the right strength, and it illustrates how a rigorous application of the leading logarithm approximation might work in quantum gravity. It also serves as a partial test of the 'null hypothesis' that there are no significant effects from infrared gravitons.

  2. IRIS Simplified LERF Model

    International Nuclear Information System (INIS)

    Maioli, A.; Finnicum, D.J.; Kumagai, Y.

    2004-01-01

    Westinghouse is currently conducting the pre-application licensing of the International Reactor Innovative and Secure (IRIS). One of the key aspects of the IRIS design is its safety-by-designTM philosophy and within this framework the PRA is being used as an integral part of the design process. The most ambitious risk-related goal for IRIS is to reduce the Emergency Planning Zone (EPZ) to within the exclusion area by demonstrating that the off-site doses are consistent with the US Protective Action Guidelines (PAGs) for initiation of emergency response so that the required protective actions would be limited to the exclusion area. As a first step, a model has been developed to provide a first order approximation of the Large Early Release Frequency (LERF) as a surrogate predictor of the off-site doses. A key-aspect of the LERF model development is the characterization of the possible paths of release. Four main categories have been historically pointed out: (1) Core Damage (CD ) sequences with containment bypass, (2) CD sequences with containment isolation failure, (3) CD sequences with containment failure at low pressure and (4) CD sequences with containment failure at high pressure. They have been reevaluated to account for the IRIS design features

  3. Extreme-value limit of the convolution of exponential and multivariate normal distributions: Link to the Hüsler–Reiß distribution

    KAUST Repository

    Krupskii, Pavel; Joe, Harry; Lee, David; Genton, Marc G.

    2017-01-01

    The multivariate Hüsler–Reiß copula is obtained as a direct extreme-value limit from the convolution of a multivariate normal random vector and an exponential random variable multiplied by a vector of constants. It is shown how the set of Hüsler–Reiß parameters can be mapped to the parameters of this convolution model. Assuming there are no singular components in the Hüsler–Reiß copula, the convolution model leads to exact and approximate simulation methods. An application of simulation is to check if the Hüsler–Reiß copula with different parsimonious dependence structures provides adequate fit to some data consisting of multivariate extremes.

  4. Extreme-value limit of the convolution of exponential and multivariate normal distributions: Link to the Hüsler–Reiß distribution

    KAUST Repository

    Krupskii, Pavel

    2017-11-02

    The multivariate Hüsler–Reiß copula is obtained as a direct extreme-value limit from the convolution of a multivariate normal random vector and an exponential random variable multiplied by a vector of constants. It is shown how the set of Hüsler–Reiß parameters can be mapped to the parameters of this convolution model. Assuming there are no singular components in the Hüsler–Reiß copula, the convolution model leads to exact and approximate simulation methods. An application of simulation is to check if the Hüsler–Reiß copula with different parsimonious dependence structures provides adequate fit to some data consisting of multivariate extremes.

  5. Breaking Through the Multi-Mesa-Channel Width Limited of Normally Off GaN HEMTs Through Modulation of the Via-Hole-Length.

    Science.gov (United States)

    Chien, Cheng-Yen; Wu, Wen-Hsin; You, Yao-Hong; Lin, Jun-Huei; Lee, Chia-Yu; Hsu, Wen-Ching; Kuan, Chieh-Hsiung; Lin, Ray-Ming

    2017-12-01

    We present new normally off GaN high-electron-mobility transistors (HEMTs) that overcome the typical limitations in multi-mesa-channel (MMC) width through modulation of the via-hole-length to regulate the charge neutrality screen effect. We have prepared enhancement-mode (E-mode) GaN HEMTs having widths of up to 300 nm, based on an enhanced surface pinning effect. E-mode GaN HEMTs having MMC structures and widths as well as via-hole-lengths of 100 nm/2 μm and 300 nm/6 μm, respectively, exhibited positive threshold voltages (V th ) of 0.79 and 0.46 V, respectively. The on-resistances of the MMC and via-hole-length structures were lower than those of typical tri-gate nanoribbon GaN HEMTs. In addition, the devices not only achieved the E-mode but also improved the power performance of the GaN HEMTs and effectively mitigated the device thermal effect. We controlled the via-hole-length sidewall surface pinning effect to obtain the E-mode GaN HEMTs. Our findings suggest that via-hole-length normally off GaN HEMTs have great potential for use in next-generation power electronics.

  6. Breaking Through the Multi-Mesa-Channel Width Limited of Normally Off GaN HEMTs Through Modulation of the Via-Hole-Length

    Science.gov (United States)

    Chien, Cheng-Yen; Wu, Wen-Hsin; You, Yao-Hong; Lin, Jun-Huei; Lee, Chia-Yu; Hsu, Wen-Ching; Kuan, Chieh-Hsiung; Lin, Ray-Ming

    2017-06-01

    We present new normally off GaN high-electron-mobility transistors (HEMTs) that overcome the typical limitations in multi-mesa-channel (MMC) width through modulation of the via-hole-length to regulate the charge neutrality screen effect. We have prepared enhancement-mode (E-mode) GaN HEMTs having widths of up to 300 nm, based on an enhanced surface pinning effect. E-mode GaN HEMTs having MMC structures and widths as well as via-hole-lengths of 100 nm/2 μm and 300 nm/6 μm, respectively, exhibited positive threshold voltages ( V th) of 0.79 and 0.46 V, respectively. The on-resistances of the MMC and via-hole-length structures were lower than those of typical tri-gate nanoribbon GaN HEMTs. In addition, the devices not only achieved the E-mode but also improved the power performance of the GaN HEMTs and effectively mitigated the device thermal effect. We controlled the via-hole-length sidewall surface pinning effect to obtain the E-mode GaN HEMTs. Our findings suggest that via-hole-length normally off GaN HEMTs have great potential for use in next-generation power electronics.

  7. Simplified design of filter circuits

    CERN Document Server

    Lenk, John

    1999-01-01

    Simplified Design of Filter Circuits, the eighth book in this popular series, is a step-by-step guide to designing filters using off-the-shelf ICs. The book starts with the basic operating principles of filters and common applications, then moves on to describe how to design circuits by using and modifying chips available on the market today. Lenk's emphasis is on practical, simplified approaches to solving design problems.Contains practical designs using off-the-shelf ICsStraightforward, no-nonsense approachHighly illustrated with manufacturer's data sheets

  8. Ramp - Metering Algorithms Evaluated within Simplified Conditions

    Science.gov (United States)

    Janota, Aleš; Holečko, Peter; Gregor, Michal; Hruboš, Marián

    2017-12-01

    Freeway networks reach their limits, since it is usually impossible to increase traffic volumes by indefinitely extending transport infrastructure through adding new traffic lanes. One of the possible solutions is to use advanced intelligent transport systems, particularly ramp metering systems. The paper shows how two particular algorithms of local and traffic-responsive control (Zone, ALINEA) can be adapted to simplified conditions corresponding to Slovak freeways. Both control strategies are modelled and simulated using PTV Vissim software, including the module VisVAP. Presented results demonstrate the properties of both control strategies, which are compared mutually as well as with the initial situation in which no control strategy is applied

  9. Ramp - Metering Algorithms Evaluated within Simplified Conditions

    Directory of Open Access Journals (Sweden)

    Janota Aleš

    2017-12-01

    Full Text Available Freeway networks reach their limits, since it is usually impossible to increase traffic volumes by indefinitely extending transport infrastructure through adding new traffic lanes. One of the possible solutions is to use advanced intelligent transport systems, particularly ramp metering systems. The paper shows how two particular algorithms of local and traffic-responsive control (Zone, ALINEA can be adapted to simplified conditions corresponding to Slovak freeways. Both control strategies are modelled and simulated using PTV Vissim software, including the module VisVAP. Presented results demonstrate the properties of both control strategies, which are compared mutually as well as with the initial situation in which no control strategy is applied

  10. Simplified High-Power Inverter

    Science.gov (United States)

    Edwards, D. B.; Rippel, W. E.

    1984-01-01

    Solid-state inverter simplified by use of single gate-turnoff device (GTO) to commutate multiple silicon controlled rectifiers (SCR's). By eliminating conventional commutation circuitry, GTO reduces cost, size and weight. GTO commutation applicable to inverters of greater than 1-kilowatt capacity. Applications include emergency power, load leveling, drives for traction and stationary polyphase motors, and photovoltaic-power conditioning.

  11. Control of activation levels to simplify waste management of fusion reactor ferritic steel components

    International Nuclear Information System (INIS)

    Wiffen, F.W.; Santoro, R.T.

    1983-01-01

    Activation characteristics of a material for service in the neutron flux of a fusion reactor first wall fall into three areas: waste management, reactor maintenance and repair, and safety. Of these, the waste management area is the most likely to impact the public acceptance of fusion reactors for power generation. The decay of the activity in steels within tens of years could lead to simplified waste disposal or possibly even to materials recycle. Whether or not these can be achieved will be controlled by (1) selection of alloying elements, (2) control of critical impurity elements, and (3) control of cross contamination from other reactor components. Several criteria can be used to judge the acceptability of potential alloying elements in iron, and to define the limits on content of critical impurity elements. One approach is to select and limit alloying additions on the basis of the activity. If material recycle is a goal, N, Al, Ni, Cu, Nb, and Mo must be excluded. If simplified waste storage by shallow land burial is the goal, regulations limit the concentration of only a few isotopes. For first-wall material that will be exposed to 9 MW-y/m 2 service, allowable initial concentration limits include (in at. ppM) Ni < 20,000; Mo < 3650; N < 3650, Cu < 2400; and Nb < 1.0. The other constituent elements of ferritic steels will not be limited. Possible substitutes for the molybdenum normally used to strengthen the steels include W, Ta, Ti, and V

  12. Simple serum markers for significant liver inflammation in chronic hepatitis B patients with an alanine aminotransferase level lower than 2 times upper limit of normal

    Directory of Open Access Journals (Sweden)

    LI Qiang

    2016-06-01

    Full Text Available ObjectiveTo investigate the simple serum markers for significant liver inflammation in chronic hepatitis B (CHB patients with an alanine aminotransferase (ALT level of <2 times upper limit of normal (ULN. MethodsThe clinical data of 278 CHB patients with ALT <2×ULN (ULN=40 U/L were analyzed retrospectively. Significant liver inflammation was defined as a liver inflammatory activity grade (G ≥2. The t-test was used for comparison of normally distributed continuous data between groups, and the Kruskal-Wallis rank sum test was used for non-normally distributed continuous data; the chi-square test was used for comparison of categorical data between groups. Multivariate logistic regression analysis was used to identify independent predictors for significant liver inflammation in CHB patients with ALT <2×ULN. The receiver operating characteristic (ROC curve was used to evaluate the diagnostic value of serum markers in significant liver inflammation. ResultsOf the 278 CHB patients enrolled, 175 (62.9% had no significant liver inflammation (G0-1 group and 103 (37.1% had significant liver inflammation (G2-4 group. There were significant differences in ALT, aspartate aminotransferase, alkaline phosphatase, gamma-glutamyl transpeptidase (GGT, albumin, globulin, prothrombin time (PT, platelet, absolute neutrophil count, hyaluronic acid (HA, glycocholic acid, precollagen Ⅲ, and collagen type Ⅳ(ⅣC between the two groups (all P<0.05. The multivariate regression analysis showed that GGT, PT, ⅣC, and HA were independent predictors for significant liver inflammation in CHB patients with ALT<2×ULN (OR=1.015, 1.600, 1.151, and 1.014, P=0.008, 0.021, 0.003, and 0.018. The areas under the ROC curve for GGT, PT, IVC, and HA to diagnose significant liver inflammation were 0.804, 0.722, 0.707, and 0.632, respectively. The cut-off value of 48.5 U/L for GGT to predict significant liver inflammation had a specificity of 90.3% and a negative

  13. Limits on normal cochlear 'third' windows provided by previous investigations of additional sound paths into and out of the cat inner ear.

    Science.gov (United States)

    Rosowski, John J; Bowers, Peter; Nakajima, Hideko H

    2018-03-01

    While most models of cochlear function assume the presence of only two windows into the mammalian cochlea (the oval and round windows), a position that is generally supported by several lines of data, there is evidence for additional sound paths into and out of the inner ear in normal mammals. In this report we review the existing evidence for and against the 'two-window' hypothesis. We then determine how existing data and inner-ear anatomy restrict transmission of sound through these additional sound pathways in cat by utilizing a well-tested model of the cat inner ear, together with anatomical descriptions of the cat cochlear and vestibular aqueducts (potential additional windows to the cochlea). We conclude: (1) The existing data place limits on the size of the cochlear and vestibular aqueducts in cat and are consistent with small volume-velocities through these ducts during ossicular stimulation of the cochlea, (2) the predicted volume velocities produced by aqueducts with diameters half the size of the bony diameters match the functional data within ±10 dB, and (3) these additional volume velocity paths contribute to the inner ear's response to non-acoustic stimulation and conductive pathology. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Correlation of cardiac Troponin I levels (10 folds upper limit of normal) and extent of coronary artery disease in Non-ST elevation myocardial infarction

    International Nuclear Information System (INIS)

    Qadir, F.; Khan, M.; Hanif, B.; Lakhani, S.L.; Farooq, S.

    2010-01-01

    Objective: To determine the correlation of cardiac troponin I (cTnI) 10 folds upper limit of normal (ULN) and extent of coronary artery disease (CAD) in Non-ST-elevation myocardial infarction (NSTEMI). Methods: A cross-sectional study was conducted on 230 consecutive NSTEMI patients admitted in Tabba Heart Institute, Karachi between April to December 2008. cTnI was measured using MEIA method. All patients underwent coronary angiography in the index hospitalization. Stenosis > 70% in any of the three major epicardial vessels was considered significant CAD. Extent of CAD was defined as significant single, two or three vessel CAD. Chi-square test was applied to test the association between cTnI levels and CAD extent. Results: Out of 230 patients, in 111 patients with cTnI levels 10 folds ULN, 23(19.3%) had single vessel, 37(31.1 %) had two vessel and 55(46.2%) had three vessel significant CAD. The results suggest that there was an insignificant association between the cTnI levels and single vessel, two vessel and the overall CAD extent (p= 0.35, p= 0.21 and p= 0.13 respectively), however there was a statistically significant association between the cTnI levels and three vessel CAD (p < 0.04). Conclusion: Higher cTnI levels are associated with an increased proportion of severe three vessel CAD involvement. Prompt identification and referral of this patient subset to early revascularization strategies would improve clinical outcomes. (author)

  15. Simplified models of mixed dark matter

    International Nuclear Information System (INIS)

    Cheung, Clifford; Sanford, David

    2014-01-01

    We explore simplified models of mixed dark matter (DM), defined here to be a stable relic composed of a singlet and an electroweak charged state. Our setup describes a broad spectrum of thermal DM candidates that can naturally accommodate the observed DM abundance but are subject to substantial constraints from current and upcoming direct detection experiments. We identify ''blind spots'' at which the DM-Higgs coupling is identically zero, thus nullifying direct detection constraints on spin independent scattering. Furthermore, we characterize the fine-tuning in mixing angles, i.e. well-tempering, required for thermal freeze-out to accommodate the observed abundance. Present and projected limits from LUX and XENON1T force many thermal relic models into blind spot tuning, well-tempering, or both. This simplified model framework generalizes bino-Higgsino DM in the MSSM, singlino-Higgsino DM in the NMSSM, and scalar DM candidates that appear in models of extended Higgs sectors

  16. Simplified design of IC amplifiers

    CERN Document Server

    Lenk, John

    1996-01-01

    Simplified Design of IC Amplifiers has something for everyone involved in electronics. No matter what skill level, this book shows how to design and experiment with IC amplifiers. For experimenters, students, and serious hobbyists, this book provides sufficient information to design and build IC amplifier circuits from 'scratch'. For working engineers who design amplifier circuits or select IC amplifiers, the book provides a variety of circuit configurations to make designing easier.Provides basics for all phases of practical design.Covers the most popular forms for amplif

  17. A simplified indirect bonding technique

    Directory of Open Access Journals (Sweden)

    Radha Katiyar

    2014-01-01

    Full Text Available With the advent of lingual orthodontics, indirect bonding technique has become an integral part of practice. It involves placement of brackets initially on the models and then their transfer to teeth with the help of transfer trays. Problems encountered with current indirect bonding techniques used are (1 the possibility of adhesive flash remaining around the base of the brackets which requires removal (2 longer time required for the adhesive to gain enough bond strength for secure tray removal. The new simplified indirect bonding technique presented here overcomes both these problems.

  18. Simplified propagation of standard uncertainties

    International Nuclear Information System (INIS)

    Shull, A.H.

    1997-01-01

    An essential part of any measurement control program is adequate knowledge of the uncertainties of the measurement system standards. Only with an estimate of the standards'' uncertainties can one determine if the standard is adequate for its intended use or can one calculate the total uncertainty of the measurement process. Purchased standards usually have estimates of uncertainty on their certificates. However, when standards are prepared and characterized by a laboratory, variance propagation is required to estimate the uncertainty of the standard. Traditional variance propagation typically involves tedious use of partial derivatives, unfriendly software and the availability of statistical expertise. As a result, the uncertainty of prepared standards is often not determined or determined incorrectly. For situations meeting stated assumptions, easier shortcut methods of estimation are now available which eliminate the need for partial derivatives and require only a spreadsheet or calculator. A system of simplifying the calculations by dividing into subgroups of absolute and relative uncertainties is utilized. These methods also incorporate the International Standards Organization (ISO) concepts for combining systematic and random uncertainties as published in their Guide to the Expression of Measurement Uncertainty. Details of the simplified methods and examples of their use are included in the paper

  19. Weight-band dosing tables: simplifying paediatric art | Nuttall ...

    African Journals Online (AJOL)

    One of the obstacles to scaling up paediatric antiretroviral therapy (ART) coverage in resource-limited settings is the relative complexity of paediatric dosing. There is a need to simplify ART in order to facilitate treatment initiation and ongoing management of infants and children by health care providers, as well as to support ...

  20. Simplifying the circuit of Josephson parametric converters

    Science.gov (United States)

    Abdo, Baleegh; Brink, Markus; Chavez-Garcia, Jose; Keefe, George

    Josephson parametric converters (JPCs) are quantum-limited three-wave mixing devices that can play various important roles in quantum information processing in the microwave domain, including amplification of quantum signals, transduction of quantum information, remote entanglement of qubits, nonreciprocal amplification, and circulation of signals. However, the input-output and biasing circuit of a state-of-the-art JPC consists of bulky components, i.e. two commercial off-chip broadband 180-degree hybrids, four phase-matched short coax cables, and one superconducting magnetic coil. Such bulky hardware significantly hinders the integration of JPCs in scalable quantum computing architectures. In my talk, I will present ideas on how to simplify the JPC circuit and show preliminary experimental results

  1. Simplified theory of an active lift turbine with controlled displacement

    OpenAIRE

    Lecanu , Pierre ,; Breard , Joel; Mouazé , Dominique

    2016-01-01

    It is presented in this article, a simplified theory of the active lift turbine which has been the subject of several patent[4, 5, 11]. A simplified theory is proposed to extend the Betz limit of the yield on vertical axis wind turbine. This work can be extended either on wind driven or marine current turbine. Based on kinetic energy calculation , that theory demonstrates that the radial force acting on the blade can be used to extend the maximum recoverable power, mainly by transforming a li...

  2. Simplified compact containment BWR plant

    International Nuclear Information System (INIS)

    Heki, H.; Nakamaru, M.; Tsutagawa, M.; Hiraiwa, K.; Arai, K.; Hida, T.

    2004-01-01

    The reactor concept considered in this paper has a small power output, a compact containment and a simplified BWR configuration with comprehensive safety features. The Compact Containment Boiling Water Reactor (CCR), which is being developed with matured BWR technologies together with innovative systems/components, is expected to prove attractive in the world energy markets due to its flexibility in regard to both energy demands and site conditions, its high potential for reducing investment risk and its safety features facilitating public acceptance. The flexibility is achieved by CCR's small power output of 300 MWe class and capability of long operating cycle (refueling intervals). CCR is expected to be attractive from view point of investment due to its simplification/innovation in design such as natural circulation core cooling with the bottom located short core, internal upper entry control rod drives (CRDs) with ring-type dryers and simplified ECCS system with high pressure containment concept. The natural circulation core eliminates recirculation pumps and the maintenance of such pumps. The internal upper entry CRDs reduce the height of the reactor vessel (RPV) and consequently reduce the height of the primary containment vessel (PCV). The safety features mainly consist of large water inventory above the core without large penetration below the top of the core, passive cooling system by isolation condenser (IC), passive auto catalytic recombiner and in-vessel retention (IVR) capability. The large inventory increases the system response time in the case of design-base accidents, including loss of coolant accidents. The IC suppresses PCV pressure by steam condensation without any AC power. The recombiner decreases hydrogen concentration in the PCV in the case of a severe accident. Cooling the molten core inside the RPV if the core should be damaged by loss of core coolability could attain the IVR. The feasibility of CCR safety system has been confirmed by LOCA

  3. Simplified model for DNB analysis

    International Nuclear Information System (INIS)

    Silva Filho, E.

    1979-08-01

    In a pressurized water nuclear reactor (PWR), the power of operation is restricted by the possibility of the occurrence of the departure from nucleate boiling called DNB (Departure from Nucleate Boiling) in the hottest channel of the core. The present work proposes a simplified model that analyses the thermal-hydraulic conditions of the coolant in the hottest channel of PWRs with the objective to evaluate BNB in this channel. For this the coupling between the hot channel and typical nominal channels assumed imposing the existence of a cross flow between these channels in a way that a uniforme pressure axial distribution results along the channels. The model is applied for Angra-I reactor and the results are compared with those of Final Safety Analysis Report (FSAR) obtained by Westinghouse through the THINC program, beeing considered satisfactory (Author) [pt

  4. Food consumption of adolescents. A simplified questionnaire for evaluating cardiovascular risk

    Directory of Open Access Journals (Sweden)

    Chiara Vera Lucia

    2001-01-01

    Full Text Available OBJECTIVE: To develop a simplified questionnaire for self-evaluation by adolescents of foods associated with the risk of coronary diseases. METHODS: Frequency questionnaires about 80 foods were answered by representative samples of 256 adolescents aged 12 to 19 from Rio de Janeiro as part of the Nutrition and Health Research project. The dependent variable was the serum cholesterol predicting equation as influenced by diet, and the independent variables were the foods. The variables were normalized and, using Pearson's correlation coefficient, those with r>0.10 were selected for the regression model. The model was analyzed for sex, age, random sample, and total calories. Those food products that explained 85% of the cholesterol variation equation were present in the caloric model, and contained trans fatty acids were selected for the questionnaire. RESULTS: Sixty-five food products had a statistically significant correlation (P<0.001 with the dependent variable. The simplified questionnaire included 9 food products present in all tested models: steak or broiled meat, hamburger, full-fat cheese, French fries or potato chips, whole milk, pies or cakes, cookies, sausages, butter or margarine. The limit of the added food points for self-evaluation was 100, and over 120 points was considered excessive. CONCLUSION: The scores given to the food products and the criteria for the evaluation of the consumption limits enabled the adolescents to get to know and to balance their intake.

  5. Simplified SUSY at the ILC

    Energy Technology Data Exchange (ETDEWEB)

    Berggren, Mikael

    2013-08-15

    At the ILC, one has the possibility to search for SUSY in an model-independent way: The corner-stone of SUSY is that sparticles couple as particles. This is independent of the mechanism responsible for SUSY breaking. Any model will have one Lightest SUSY Particle (LSP), and one Next to Lightest SUSY Particle (NLSP). In models with conserved R-parity, the NLSP must decay solely to the LSP and the SM partner of the NLSP. Therefore, studying NLSP production and decay can be regarded as a ''simplified model without simplification'': Any SUSY model will have such a process. The NLSP could be any sparticle: a slepton, an electroweak-ino, or even a squark. However, since there are only a finite number of sparticles, one can systematically search for signals of all possible NLSP:s. This way, the entire space of models that have a kinematically reachable NLSP can be covered. For any NLSP, the ''worst case'' can be determined, since the SUSY principle allows to calculate the cross-section once the NLSP nature and mass are given. The region in the LSP-NLSP mass-plane where the ''worst case'' could be discovered or excluded experimentally can be found by estimating background and efficiency at each point in the plane. From experience at LEP, it is expected that the lower signal-to background ratio will indeed be found for models with conserved R-parity. In this document, we show that at the ILC, such a program is possible, as it was at LEP. No loop-holes are left, even for difficult or non-standard cases: whatever the NLSP is it will be detectable.

  6. Simplified SUSY at the ILC

    International Nuclear Information System (INIS)

    Berggren, Mikael

    2013-08-01

    At the ILC, one has the possibility to search for SUSY in an model-independent way: The corner-stone of SUSY is that sparticles couple as particles. This is independent of the mechanism responsible for SUSY breaking. Any model will have one Lightest SUSY Particle (LSP), and one Next to Lightest SUSY Particle (NLSP). In models with conserved R-parity, the NLSP must decay solely to the LSP and the SM partner of the NLSP. Therefore, studying NLSP production and decay can be regarded as a ''simplified model without simplification'': Any SUSY model will have such a process. The NLSP could be any sparticle: a slepton, an electroweak-ino, or even a squark. However, since there are only a finite number of sparticles, one can systematically search for signals of all possible NLSP:s. This way, the entire space of models that have a kinematically reachable NLSP can be covered. For any NLSP, the ''worst case'' can be determined, since the SUSY principle allows to calculate the cross-section once the NLSP nature and mass are given. The region in the LSP-NLSP mass-plane where the ''worst case'' could be discovered or excluded experimentally can be found by estimating background and efficiency at each point in the plane. From experience at LEP, it is expected that the lower signal-to background ratio will indeed be found for models with conserved R-parity. In this document, we show that at the ILC, such a program is possible, as it was at LEP. No loop-holes are left, even for difficult or non-standard cases: whatever the NLSP is it will be detectable.

  7. Simplified Models for LHC New Physics Searches

    CERN Document Server

    Alves, Daniele; Arora, Sanjay; Bai, Yang; Baumgart, Matthew; Berger, Joshua; Buckley, Matthew; Butler, Bart; Chang, Spencer; Cheng, Hsin-Chia; Cheung, Clifford; Chivukula, R.Sekhar; Cho, Won Sang; Cotta, Randy; D'Alfonso, Mariarosaria; El Hedri, Sonia; Essig, Rouven; Evans, Jared A.; Fitzpatrick, Liam; Fox, Patrick; Franceschini, Roberto; Freitas, Ayres; Gainer, James S.; Gershtein, Yuri; Gray, Richard; Gregoire, Thomas; Gripaios, Ben; Gunion, Jack; Han, Tao; Haas, Andy; Hansson, Per; Hewett, JoAnne; Hits, Dmitry; Hubisz, Jay; Izaguirre, Eder; Kaplan, Jared; Katz, Emanuel; Kilic, Can; Kim, Hyung-Do; Kitano, Ryuichiro; Koay, Sue Ann; Ko, Pyungwon; Krohn, David; Kuflik, Eric; Lewis, Ian; Lisanti, Mariangela; Liu, Tao; Liu, Zhen; Lu, Ran; Luty, Markus; Meade, Patrick; Morrissey, David; Mrenna, Stephen; Nojiri, Mihoko; Okui, Takemichi; Padhi, Sanjay; Papucci, Michele; Park, Michael; Park, Myeonghun; Perelstein, Maxim; Peskin, Michael; Phalen, Daniel; Rehermann, Keith; Rentala, Vikram; Roy, Tuhin; Ruderman, Joshua T.; Sanz, Veronica; Schmaltz, Martin; Schnetzer, Stephen; Schuster, Philip; Schwaller, Pedro; Schwartz, Matthew D.; Schwartzman, Ariel; Shao, Jing; Shelton, Jessie; Shih, David; Shu, Jing; Silverstein, Daniel; Simmons, Elizabeth; Somalwar, Sunil; Spannowsky, Michael; Spethmann, Christian; Strassler, Matthew; Su, Shufang; Tait, Tim; Thomas, Brooks; Thomas, Scott; Toro, Natalia; Volansky, Tomer; Wacker, Jay; Waltenberger, Wolfgang; Yavin, Itay; Yu, Felix; Zhao, Yue; Zurek, Kathryn

    2012-01-01

    This document proposes a collection of simplified models relevant to the design of new-physics searches at the LHC and the characterization of their results. Both ATLAS and CMS have already presented some results in terms of simplified models, and we encourage them to continue and expand this effort, which supplements both signature-based results and benchmark model interpretations. A simplified model is defined by an effective Lagrangian describing the interactions of a small number of new particles. Simplified models can equally well be described by a small number of masses and cross-sections. These parameters are directly related to collider physics observables, making simplified models a particularly effective framework for evaluating searches and a useful starting point for characterizing positive signals of new physics. This document serves as an official summary of the results from the "Topologies for Early LHC Searches" workshop, held at SLAC in September of 2010, the purpose of which was to develop a...

  8. Interpretation of searches for supersymmetry with simplified models

    Energy Technology Data Exchange (ETDEWEB)

    Chatrchyan, S.; Khachatryan, V.; Sirunyan, A. M.; Tumasyan, A.; Adam, W.; Aguilo, E.; Bergauer, T.; Dragicevic, M.; Erö, J.; Fabjan, C.; Friedl, M.; Frühwirth, R.; Ghete, V. M.; Hörmann, N.; Hrubec, J.; Jeitler, M.; Kiesenhofer, W.; Knünz, V.; Krammer, M.; Krätschmer, I.; Liko, D.; Mikulec, I.; Pernicka, M.; Rabady, D.; Rahbaran, B.; Rohringer, C.; Rohringer, H.; Schöfbeck, R.; Strauss, J.; Taurok, A.; Waltenberger, W.; Wulz, C. -E.; Mossolov, V.; Shumeiko, N.; Suarez Gonzalez, J.; Bansal, M.; Bansal, S.; Cornelis, T.; De Wolf, E. A.; Janssen, X.; Luyckx, S.; Mucibello, L.; Ochesanu, S.; Roland, B.; Rougny, R.; Selvaggi, M.; Van Haevermaet, H.; Van Mechelen, P.; Van Remortel, N.; Van Spilbeeck, A.; Blekman, F.; Blyweert, S.; D’Hondt, J.; Gonzalez Suarez, R.; Kalogeropoulos, A.; Maes, M.; Olbrechts, A.; Van Doninck, W.; Van Mulders, P.; Van Onsem, G. P.; Villella, I.; Clerbaux, B.; De Lentdecker, G.; Dero, V.; Gay, A. P. R.; Hreus, T.; Léonard, A.; Marage, P. E.; Mohammadi, A.; Reis, T.; Thomas, L.; Vander Velde, C.; Vanlaer, P.; Wang, J.; Adler, V.; Beernaert, K.; Cimmino, A.; Costantini, S.; Garcia, G.; Grunewald, M.; Klein, B.; Lellouch, J.; Marinov, A.; Mccartin, J.; Ocampo Rios, A. A.; Ryckbosch, D.; Strobbe, N.; Thyssen, F.; Tytgat, M.; Walsh, S.; Yazgan, E.; Zaganidis, N.; Basegmez, S.; Bruno, G.; Castello, R.; Ceard, L.; Delaere, C.; du Pree, T.; Favart, D.; Forthomme, L.; Giammanco, A.; Hollar, J.; Lemaitre, V.; Liao, J.; Militaru, O.; Nuttens, C.; Pagano, D.; Pin, A.; Piotrzkowski, K.; Vizan Garcia, J. M.; Beliy, N.; Caebergs, T.; Daubie, E.; Hammad, G. H.; Alves, G. A.; Correa Martins Junior, M.; Martins, T.; Pol, M. E.; Souza, M. H. G.; Aldá Júnior, W. L.; Carvalho, W.; Custódio, A.; Da Costa, E. M.; De Jesus Damiao, D.; De Oliveira Martins, C.; Fonseca De Souza, S.; Malbouisson, H.; Malek, M.; Matos Figueiredo, D.; Mundim, L.; Nogima, H.; Prado Da Silva, W. L.; Santoro, A.; Soares Jorge, L.; Sznajder, A.; Vilela Pereira, A.; Anjos, T. S.; Bernardes, C. A.; Dias, F. A.; Fernandez Perez Tomei, T. R.; Gregores, E. M.; Lagana, C.; Marinho, F.; Mercadante, P. G.; Novaes, S. F.; Padula, Sandra S.; Genchev, V.; Iaydjiev, P.; Piperov, S.; Rodozov, M.; Stoykova, S.; Sultanov, G.; Tcholakov, V.; Trayanov, R.; Vutova, M.; Dimitrov, A.; Hadjiiska, R.; Kozhuharov, V.; Litov, L.; Pavlov, B.; Petkov, P.; Bian, J. G.; Chen, G. M.; Chen, H. S.; Jiang, C. H.; Liang, D.; Liang, S.; Meng, X.; Tao, J.; Wang, J.; Wang, X.; Wang, Z.; Xiao, H.; Xu, M.; Zang, J.; Zhang, Z.; Asawatangtrakuldee, C.; Ban, Y.; Guo, Y.; Li, W.; Liu, S.; Mao, Y.; Qian, S. J.; Teng, H.; Wang, D.; Zhang, L.; Zou, W.; Avila, C.; Gomez, J. P.; Gomez Moreno, B.; Osorio Oliveros, A. F.; Sanabria, J. C.; Godinovic, N.; Lelas, D.; Plestina, R.; Polic, D.; Puljak, I.; Antunovic, Z.; Kovac, M.; Brigljevic, V.; Duric, S.; Kadija, K.; Luetic, J.; Mekterovic, D.; Morovic, S.; Attikis, A.; Galanti, M.; Mavromanolakis, G.; Mousa, J.; Nicolaou, C.; Ptochos, F.; Razis, P. A.; Finger, M.; Finger, M.; Assran, Y.; Elgammal, S.; Ellithi Kamel, A.; Mahmoud, M. A.; Mahrous, A.; Radi, A.; Kadastik, M.; Müntel, M.; Raidal, M.; Rebane, L.; Tiko, A.; Eerola, P.; Fedi, G.; Voutilainen, M.; Härkönen, J.; Heikkinen, A.; Karimäki, V.; Kinnunen, R.; Kortelainen, M. J.; Lampén, T.; Lassila-Perini, K.; Lehti, S.; Lindén, T.; Luukka, P.; Mäenpää, T.; Peltola, T.; Tuominen, E.; Tuominiemi, J.; Tuovinen, E.; Ungaro, D.; Wendland, L.; Banzuzi, K.; Karjalainen, A.; Korpela, A.; Tuuva, T.; Besancon, M.; Choudhury, S.; Dejardin, M.; Denegri, D.; Fabbro, B.; Faure, J. L.; Ferri, F.; Ganjour, S.; Givernaud, A.; Gras, P.; Hamel de Monchenault, G.; Jarry, P.; Locci, E.; Malcles, J.; Millischer, L.; Nayak, A.; Rander, J.; Rosowsky, A.; Titov, M.; Baffioni, S.; Beaudette, F.; Benhabib, L.; Bianchini, L.; Bluj, M.; Busson, P.; Charlot, C.; Daci, N.; Dahms, T.; Dalchenko, M.; Dobrzynski, L.; Florent, A.; Granier de Cassagnac, R.; Haguenauer, M.; Miné, P.; Mironov, C.; Naranjo, I. N.; Nguyen, M.; Ochando, C.; Paganini, P.; Sabes, D.; Salerno, R.; Sirois, Y.; Veelken, C.; Zabi, A.; Agram, J. -L.; Andrea, J.; Bloch, D.; Bodin, D.; Brom, J. -M.; Cardaci, M.; Chabert, E. C.; Collard, C.; Conte, E.; Drouhin, F.; Fontaine, J. -C.; Gelé, D.; Goerlach, U.; Juillot, P.; Le Bihan, A. -C.; Van Hove, P.; Fassi, F.; Mercier, D.; Beauceron, S.; Beaupere, N.; Bondu, O.; Boudoul, G.; Brochet, S.; Chasserat, J.; Chierici, R.; Contardo, D.; Depasse, P.; El Mamouni, H.; Fay, J.; Gascon, S.; Gouzevitch, M.; Ille, B.; Kurca, T.; Lethuillier, M.; Mirabito, L.; Perries, S.; Sgandurra, L.; Sordini, V.; Tschudi, Y.; Verdier, P.; Viret, S.; Tsamalaidze, Z.; Autermann, C.; Beranek, S.; Calpas, B.; Edelhoff, M.; Feld, L.; Heracleous, N.; Hindrichs, O.; Jussen, R.; Klein, K.; Merz, J.; Ostapchuk, A.; Perieanu, A.; Raupach, F.; Sammet, J.; Schael, S.; Sprenger, D.; Weber, H.; Wittmer, B.; Zhukov, V.; Ata, M.; Caudron, J.; Dietz-Laursonn, E.; Duchardt, D.; Erdmann, M.; Fischer, R.; Güth, A.; Hebbeker, T.; Heidemann, C.; Hoepfner, K.; Klingebiel, D.; Kreuzer, P.; Merschmeyer, M.; Meyer, A.; Olschewski, M.; Papacz, P.; Pieta, H.; Reithler, H.; Schmitz, S. A.; Sonnenschein, L.; Steggemann, J.; Teyssier, D.; Thüer, S.; Weber, M.; Bontenackels, M.; Cherepanov, V.; Erdogan, Y.; Flügge, G.; Geenen, H.; Geisler, M.; Haj Ahmad, W.; Hoehle, F.; Kargoll, B.; Kress, T.; Kuessel, Y.; Lingemann, J.; Nowack, A.; Perchalla, L.; Pooth, O.; Sauerland, P.; Stahl, A.; Aldaya Martin, M.; Behr, J.; Behrenhoff, W.; Behrens, U.; Bergholz, M.; Bethani, A.; Borras, K.; Burgmeier, A.; Cakir, A.; Calligaris, L.; Campbell, A.; Castro, E.; Costanza, F.; Dammann, D.; Diez Pardos, C.; Eckerlin, G.; Eckstein, D.; Flucke, G.; Geiser, A.; Glushkov, I.; Gunnellini, P.; Habib, S.; Hauk, J.; Hellwig, G.; Jung, H.; Kasemann, M.; Katsas, P.; Kleinwort, C.; Kluge, H.; Knutsson, A.; Krämer, M.; Krücker, D.; Kuznetsova, E.; Lange, W.; Leonard, J.; Lohmann, W.; Lutz, B.; Mankel, R.; Marfin, I.; Marienfeld, M.; Melzer-Pellmann, I. -A.; Meyer, A. B.; Mnich, J.; Mussgiller, A.; Naumann-Emme, S.; Novgorodova, O.; Olzem, J.; Perrey, H.; Petrukhin, A.; Pitzl, D.; Raspereza, A.; Ribeiro Cipriano, P. M.; Riedl, C.; Ron, E.; Rosin, M.; Salfeld-Nebgen, J.; Schmidt, R.; Schoerner-Sadenius, T.; Sen, N.; Spiridonov, A.; Stein, M.; Walsh, R.; Wissing, C.; Blobel, V.; Enderle, H.; Erfle, J.; Gebbert, U.; Görner, M.; Gosselink, M.; Haller, J.; Hermanns, T.; Höing, R. S.; Kaschube, K.; Kaussen, G.; Kirschenmann, H.; Klanner, R.; Lange, J.; Nowak, F.; Peiffer, T.; Pietsch, N.; Rathjens, D.; Sander, C.; Schettler, H.; Schleper, P.; Schlieckau, E.; Schmidt, A.; Schröder, M.; Schum, T.; Seidel, M.; Sibille, J.; Sola, V.; Stadie, H.; Steinbrück, G.; Thomsen, J.; Vanelderen, L.; Barth, C.; Berger, J.; Böser, C.; Chwalek, T.; De Boer, W.; Descroix, A.; Dierlamm, A.; Feindt, M.; Guthoff, M.; Hackstein, C.; Hartmann, F.; Hauth, T.; Heinrich, M.; Held, H.; Hoffmann, K. H.; Husemann, U.; Katkov, I.; Komaragiri, J. R.; Lobelle Pardo, P.; Martschei, D.; Mueller, S.; Müller, Th.; Niegel, M.; Nürnberg, A.; Oberst, O.; Oehler, A.; Ott, J.; Quast, G.; Rabbertz, K.; Ratnikov, F.; Ratnikova, N.; Röcker, S.; Schilling, F. -P.; Schott, G.; Simonis, H. J.; Stober, F. M.; Troendle, D.; Ulrich, R.; Wagner-Kuhr, J.; Wayand, S.; Weiler, T.; Zeise, M.; Anagnostou, G.; Daskalakis, G.; Geralis, T.; Kesisoglou, S.; Kyriakis, A.; Loukas, D.; Manolakos, I.; Markou, A.; Markou, C.; Ntomari, E.; Gouskos, L.; Mertzimekis, T. J.; Panagiotou, A.; Saoulidou, N.; Evangelou, I.; Foudas, C.; Kokkas, P.; Manthos, N.; Papadopoulos, I.; Patras, V.; Bencze, G.; Hajdu, C.; Hidas, P.; Horvath, D.; Sikler, F.; Veszpremi, V.; Vesztergombi, G.; Beni, N.; Czellar, S.; Molnar, J.; Palinkas, J.; Szillasi, Z.; Karancsi, J.; Raics, P.; Trocsanyi, Z. L.; Ujvari, B.; Beri, S. B.; Bhatnagar, V.; Dhingra, N.; Gupta, R.; Kaur, M.; Mehta, M. Z.; Nishu, N.; Saini, L. K.; Sharma, A.; Singh, J. B.; Kumar, Ashok; Kumar, Arun; Ahuja, S.; Bhardwaj, A.; Choudhary, B. C.; Malhotra, S.; Naimuddin, M.; Ranjan, K.; Sharma, V.; Shivpuri, R. K.; Banerjee, S.; Bhattacharya, S.; Dutta, S.; Gomber, B.; Jain, Sa.; Jain, Sh.; Khurana, R.; Sarkar, S.; Sharan, M.; Abdulsalam, A.; Dutta, D.; Kailas, S.; Kumar, V.; Mohanty, A. K.; Pant, L. M.; Shukla, P.; Aziz, T.; Ganguly, S.; Guchait, M.; Gurtu, A.; Maity, M.; Majumder, G.; Mazumdar, K.; Mohanty, G. B.; Parida, B.; Sudhakar, K.; Wickramage, N.; Banerjee, S.; Dugad, S.; Arfaei, H.; Bakhshiansohi, H.; Etesami, S. M.; Fahim, A.; Hashemi, M.; Hesari, H.; Jafari, A.; Khakzad, M.; Mohammadi Najafabadi, M.; Paktinat Mehdiabadi, S.; Safarzadeh, B.; Zeinali, M.; Abbrescia, M.; Barbone, L.; Calabria, C.; Chhibra, S. S.; Colaleo, A.; Creanza, D.; De Filippis, N.; De Palma, M.; Fiore, L.; Iaselli, G.; Maggi, G.; Maggi, M.; Marangelli, B.; My, S.; Nuzzo, S.; Pacifico, N.; Pompili, A.; Pugliese, G.; Selvaggi, G.; Silvestris, L.; Singh, G.; Venditti, R.; Verwilligen, P.; Zito, G.; Abbiendi, G.; Benvenuti, A. C.; Bonacorsi, D.; Braibant-Giacomelli, S.; Brigliadori, L.; Capiluppi, P.; Castro, A.; Cavallo, F. R.; Cuffiani, M.; Dallavalle, G. M.; Fabbri, F.; Fanfani, A.; Fasanella, D.; Giacomelli, P.; Grandi, C.; Guiducci, L.; Marcellini, S.; Masetti, G.; Meneghelli, M.; Montanari, A.; Navarria, F. L.; Odorici, F.; Perrotta, A.; Primavera, F.; Rossi, A. M.; Rovelli, T.; Siroli, G. P.; Tosi, N.; Travaglini, R.; Albergo, S.; Cappello, G.; Chiorboli, M.; Costa, S.; Potenza, R.; Tricomi, A.; Tuve, C.; Barbagli, G.; Ciulli, V.; Civinini, C.; D’Alessandro, R.; Focardi, E.; Frosali, S.; Gallo, E.; Gonzi, S.; Meschini, M.; Paoletti, S.; Sguazzoni, G.; Tropiano, A.; Benussi, L.; Bianco, S.; Colafranceschi, S.; Fabbri, F.; Piccolo, D.; Fabbricatore, P.; Musenich, R.; Tosi, S.; Benaglia, A.; De Guio, F.; Di Matteo, L.; Fiorendi, S.; Gennai, S.; Ghezzi, A.; Malvezzi, S.; Manzoni, R. A.; Martelli, A.; Massironi, A.; Menasce, D.; Moroni, L.; Paganoni, M.; Pedrini, D.; Ragazzi, S.; Redaelli, N.; Sala, S.; Tabarelli de Fatis, T.; Buontempo, S.; Carrillo Montoya, C. A.; Cavallo, N.; De Cosa, A.; Dogangun, O.; Fabozzi, F.; Iorio, A. O. M.; Lista, L.; Meola, S.; Merola, M.; Paolucci, P.; Azzi, P.; Bacchetta, N.; Bisello, D.; Branca, A.; Carlin, R.; Checchia, P.; Dorigo, T.; Gasparini, F.; Gozzelino, A.; Kanishchev, K.; Lacaprara, S.; Lazzizzera, I.; Margoni, M.; Meneguzzo, A. T.; Pazzini, J.; Pozzobon, N.; Ronchese, P.; Simonetto, F.; Torassa, E.; Tosi, M.; Triossi, A.; Vanini, S.; Zotto, P.; Zucchetta, A.; Zumerle, G.; Gabusi, M.; Ratti, S. P.; Riccardi, C.; Torre, P.; Vitulo, P.; Biasini, M.; Bilei, G. M.; Fanò, L.; Lariccia, P.; Mantovani, G.; Menichelli, M.; Nappi, A.; Romeo, F.; Saha, A.; Santocchia, A.; Spiezia, A.; Taroni, S.; Azzurri, P.; Bagliesi, G.; Bernardini, J.; Boccali, T.; Broccolo, G.; Castaldi, R.; D’Agnolo, R. T.; Dell’Orso, R.; Fiori, F.; Foà, L.; Giassi, A.; Kraan, A.; Ligabue, F.; Lomtadze, T.; Martini, L.; Messineo, A.; Palla, F.; Rizzi, A.; Serban, A. T.; Spagnolo, P.; Squillacioti, P.; Tenchini, R.; Tonelli, G.; Venturi, A.; Verdini, P. G.; Barone, L.; Cavallari, F.; Del Re, D.; Diemoz, M.; Fanelli, C.; Grassi, M.; Longo, E.; Meridiani, P.; Micheli, F.; Nourbakhsh, S.; Organtini, G.; Paramatti, R.; Rahatlou, S.; Sigamani, M.; Soffi, L.; Amapane, N.; Arcidiacono, R.; Argiro, S.; Arneodo, M.; Biino, C.; Cartiglia, N.; Casasso, S.; Costa, M.; Demaria, N.; Mariotti, C.; Maselli, S.; Migliore, E.; Monaco, V.; Musich, M.; Obertino, M. M.; Pastrone, N.; Pelliccioni, M.; Potenza, A.; Romero, A.; Ruspa, M.; Sacchi, R.; Solano, A.; Staiano, A.; Belforte, S.; Candelise, V.; Casarsa, M.; Cossutti, F.; Della Ricca, G.; Gobbo, B.; Marone, M.; Montanino, D.; Penzo, A.; Schizzi, A.; Kim, T. Y.; Nam, S. K.; Chang, S.; Kim, D. H.; Kim, G. N.; Kong, D. J.; Park, H.; Son, D. C.; Son, T.; Kim, J. Y.; Kim, Zero J.; Song, S.; Choi, S.; Gyun, D.; Hong, B.; Jo, M.; Kim, H.; Kim, T. J.; Lee, K. S.; Moon, D. H.; Park, S. K.; Roh, Y.; Choi, M.; Kim, J. H.; Park, C.; Park, I. C.; Park, S.; Ryu, G.; Choi, Y.; Choi, Y. K.; Goh, J.; Kim, M. S.; Kwon, E.; Lee, B.; Lee, J.; Lee, S.; Seo, H.; Yu, I.; Bilinskas, M. J.; Grigelionis, I.; Janulis, M.; Juodagalvis, A.; Castilla-Valdez, H.; De La Cruz-Burelo, E.; Heredia-de La Cruz, I.; Lopez-Fernandez, R.; Martínez-Ortega, J.; Sanchez-Hernandez, A.; Villasenor-Cendejas, L. M.; Carrillo Moreno, S.; Vazquez Valencia, F.; Salazar Ibarguen, H. A.; Casimiro Linares, E.; Morelos Pineda, A.; Reyes-Santos, M. A.; Krofcheck, D.; Bell, A. J.; Butler, P. H.; Doesburg, R.; Reucroft, S.; Silverwood, H.; Ahmad, M.; Asghar, M. I.; Butt, J.; Hoorani, H. R.; Khalid, S.; Khan, W. A.; Khurshid, T.; Qazi, S.; Shah, M. A.; Shoaib, M.; Bialkowska, H.; Boimska, B.; Frueboes, T.; Górski, M.; Kazana, M.; Nawrocki, K.; Romanowska-Rybinska, K.; Szleper, M.; Wrochna, G.; Zalewski, P.; Brona, G.; Bunkowski, K.; Cwiok, M.; Dominik, W.; Doroba, K.; Kalinowski, A.; Konecki, M.; Krolikowski, J.; Misiura, M.; Almeida, N.; Bargassa, P.; David, A.; Faccioli, P.; Ferreira Parracho, P. G.; Gallinaro, M.; Seixas, J.; Varela, J.; Vischia, P.; Bunin, P.; Gavrilenko, M.; Golutvin, I.; Gorbunov, I.; Kamenev, A.; Karjavin, V.; Kozlov, G.; Lanev, A.; Malakhov, A.; Moisenz, P.; Palichik, V.; Perelygin, V.; Savina, M.; Shmatov, S.; Smirnov, V.; Volodko, A.; Zarubin, A.; Evstyukhin, S.; Golovtsov, V.; Ivanov, Y.; Kim, V.; Levchenko, P.; Murzin, V.; Oreshkin, V.; Smirnov, I.; Sulimov, V.; Uvarov, L.; Vavilov, S.; Vorobyev, A.; Vorobyev, An.; Andreev, Yu.; Dermenev, A.; Gninenko, S.; Golubev, N.; Kirsanov, M.; Krasnikov, N.; Matveev, V.; Pashenkov, A.; Tlisov, D.; Toropin, A.; Epshteyn, V.; Erofeeva, M.; Gavrilov, V.; Kossov, M.; Lychkovskaya, N.; Popov, V.; Safronov, G.; Semenov, S.; Shreyber, I.; Stolin, V.; Vlasov, E.; Zhokin, A.; Belyaev, A.; Boos, E.; Dubinin, M.; Dudko, L.; Ershov, A.; Gribushin, A.; Klyukhin, V.; Kodolova, O.; Lokhtin, I.; Markina, A.; Obraztsov, S.; Perfilov, M.; Petrushanko, S.; Popov, A.; Sarycheva, L.; Savrin, V.; Snigirev, A.; Andreev, V.; Azarkin, M.; Dremin, I.; Kirakosyan, M.; Leonidov, A.; Mesyats, G.; Rusakov, S. V.; Vinogradov, A.; Azhgirey, I.; Bayshev, I.; Bitioukov, S.; Grishin, V.; Kachanov, V.; Konstantinov, D.; Krychkine, V.; Petrov, V.; Ryutin, R.; Sobol, A.; Tourtchanovitch, L.; Troshin, S.; Tyurin, N.; Uzunian, A.; Volkov, A.; Adzic, P.; Djordjevic, M.; Ekmedzic, M.; Krpic, D.; Milosevic, J.; Aguilar-Benitez, M.; Alcaraz Maestre, J.; Arce, P.; Battilana, C.; Calvo, E.; Cerrada, M.; Chamizo Llatas, M.; Colino, N.; De La Cruz, B.; Delgado Peris, A.; Domínguez Vázquez, D.; Fernandez Bedoya, C.; Fernández Ramos, J. P.; Ferrando, A.; Flix, J.; Fouz, M. C.; Garcia-Abia, P.; Gonzalez Lopez, O.; Goy Lopez, S.; Hernandez, J. M.; Josa, M. I.; Merino, G.; Puerta Pelayo, J.; Quintario Olmeda, A.; Redondo, I.; Romero, L.; Santaolalla, J.; Soares, M. S.; Willmott, C.; Albajar, C.; Codispoti, G.; de Trocóniz, J. F.; Brun, H.; Cuevas, J.; Fernandez Menendez, J.; Folgueras, S.; Gonzalez Caballero, I.; Lloret Iglesias, L.; Piedra Gomez, J.; Brochero Cifuentes, J. A.; Cabrillo, I. J.; Calderon, A.; Chuang, S. H.; Duarte Campderros, J.; Felcini, M.; Fernandez, M.; Gomez, G.; Gonzalez Sanchez, J.; Graziano, A.; Jorda, C.; Lopez Virto, A.; Marco, J.; Marco, R.; Martinez Rivero, C.; Matorras, F.; Munoz Sanchez, F. J.; Rodrigo, T.; Rodríguez-Marrero, A. Y.; Ruiz-Jimeno, A.; Scodellaro, L.; Vila, I.; Vilar Cortabitarte, R.; Abbaneo, D.; Auffray, E.; Auzinger, G.; Bachtis, M.; Baillon, P.; Ball, A. H.; Barney, D.; Benitez, J. F.; Bernet, C.; Bianchi, G.; Bloch, P.; Bocci, A.; Bonato, A.; Botta, C.; Breuker, H.; Camporesi, T.; Cerminara, G.; Christiansen, T.; Coarasa Perez, J. A.; D’Enterria, D.; Dabrowski, A.; De Roeck, A.; Di Guida, S.; Dobson, M.; Dupont-Sagorin, N.; Elliott-Peisert, A.; Frisch, B.; Funk, W.; Georgiou, G.; Giffels, M.; Gigi, D.; Gill, K.; Giordano, D.; Girone, M.; Giunta, M.; Glege, F.; Gomez-Reino Garrido, R.; Govoni, P.; Gowdy, S.; Guida, R.; Gundacker, S.; Hammer, J.; Hansen, M.; Harris, P.; Hartl, C.; Harvey, J.; Hegner, B.; Hinzmann, A.; Innocente, V.; Janot, P.; Kaadze, K.; Karavakis, E.; Kousouris, K.; Lecoq, P.; Lee, Y. -J.; Lenzi, P.; Lourenço, C.; Magini, N.; Mäki, T.; Malberti, M.; Malgeri, L.; Mannelli, M.; Masetti, L.; Meijers, F.; Mersi, S.; Meschi, E.; Moser, R.; Mozer, M. U.; Mulders, M.; Musella, P.; Nesvold, E.; Orsini, L.; Palencia Cortezon, E.; Perez, E.; Perrozzi, L.; Petrilli, A.; Pfeiffer, A.; Pierini, M.; Pimiä, M.; Piparo, D.; Polese, G.; Quertenmont, L.; Racz, A.; Reece, W.; Rodrigues Antunes, J.; Rolandi, G.; Rovelli, C.; Rovere, M.; Sakulin, H.; Santanastasio, F.; Schäfer, C.; Schwick, C.; Segoni, I.; Sekmen, S.; Sharma, A.; Siegrist, P.; Silva, P.; Simon, M.; Sphicas, P.; Spiga, D.; Tsirou, A.; Veres, G. I.; Vlimant, J. R.; Wöhri, H. K.; Worm, S. D.; Zeuner, W. D.; Bertl, W.; Deiters, K.; Erdmann, W.; Gabathuler, K.; Horisberger, R.; Ingram, Q.; Kaestli, H. C.; König, S.; Kotlinski, D.; Langenegger, U.; Meier, F.; Renker, D.; Rohe, T.; Bäni, L.; Bortignon, P.; Buchmann, M. A.; Casal, B.; Chanon, N.; Deisher, A.; Dissertori, G.; Dittmar, M.; Donegà, M.; Dünser, M.; Eller, P.; Eugster, J.; Freudenreich, K.; Grab, C.; Hits, D.; Lecomte, P.; Lustermann, W.; Marini, A. C.; Martinez Ruiz del Arbol, P.; Mohr, N.; Moortgat, F.; Nägeli, C.; Nef, P.; Nessi-Tedaldi, F.; Pandolfi, F.; Pape, L.; Pauss, F.; Peruzzi, M.; Ronga, F. J.; Rossini, M.; Sala, L.; Sanchez, A. K.; Starodumov, A.; Stieger, B.; Takahashi, M.; Tauscher, L.; Thea, A.; Theofilatos, K.; Treille, D.; Urscheler, C.; Wallny, R.; Weber, H. A.; Wehrli, L.; Amsler, C.; Chiochia, V.; De Visscher, S.; Favaro, C.; Ivova Rikova, M.; Kilminster, B.; Millan Mejias, B.; Otiougova, P.; Robmann, P.; Snoek, H.; Tupputi, S.; Verzetti, M.; Chang, Y. H.; Chen, K. H.; Ferro, C.; Kuo, C. M.; Li, S. W.; Lin, W.; Lu, Y. J.; Singh, A. P.; Volpe, R.; Yu, S. S.; Bartalini, P.; Chang, P.; Chang, Y. H.; Chang, Y. W.; Chao, Y.; Chen, K. F.; Dietz, C.; Grundler, U.; Hou, W. -S.; Hsiung, Y.; Kao, K. Y.; Lei, Y. J.; Lu, R. -S.; Majumder, D.; Petrakou, E.; Shi, X.; Shiu, J. G.; Tzeng, Y. M.; Wan, X.; Wang, M.; Asavapibhop, B.; Srimanobhas, N.; Adiguzel, A.; Bakirci, M. N.; Cerci, S.; Dozen, C.; Dumanoglu, I.; Eskut, E.; Girgis, S.; Gokbulut, G.; Gurpinar, E.; Hos, I.; Kangal, E. E.; Karaman, T.; Karapinar, G.; Kayis Topaksu, A.; Onengut, G.; Ozdemir, K.; Ozturk, S.; Polatoz, A.; Sogut, K.; Sunar Cerci, D.; Tali, B.; Topakli, H.; Vergili, L. N.; Vergili, M.; Akin, I. V.; Aliev, T.; Bilin, B.; Bilmis, S.; Deniz, M.; Gamsizkan, H.; Guler, A. M.; Ocalan, K.; Ozpineci, A.; Serin, M.; Sever, R.; Surat, U. E.; Yalvac, M.; Yildirim, E.; Zeyrek, M.; Gülmez, E.; Isildak, B.; Kaya, M.; Kaya, O.; Ozkorucuklu, S.; Sonmez, N.; Cankocak, K.; Levchuk, L.; Brooke, J. J.; Clement, E.; Cussans, D.; Flacher, H.; Frazier, R.; Goldstein, J.; Grimes, M.; Heath, G. P.; Heath, H. F.; Kreczko, L.; Metson, S.; Newbold, D. M.; Nirunpong, K.; Poll, A.; Senkin, S.; Smith, V. J.; Williams, T.; Basso, L.; Bell, K. W.; Belyaev, A.; Brew, C.; Brown, R. M.; Cockerill, D. J. A.; Coughlan, J. A.; Harder, K.; Harper, S.; Jackson, J.; Kennedy, B. W.; Olaiya, E.; Petyt, D.; Radburn-Smith, B. C.; Shepherd-Themistocleous, C. H.; Tomalin, I. R.; Womersley, W. J.; Bainbridge, R.; Ball, G.; Beuselinck, R.; Buchmuller, O.; Colling, D.; Cripps, N.; Cutajar, M.; Dauncey, P.; Davies, G.; Della Negra, M.; Ferguson, W.; Fulcher, J.; Futyan, D.; Gilbert, A.; Guneratne Bryer, A.; Hall, G.; Hatherell, Z.; Hays, J.; Iles, G.; Jarvis, M.; Karapostoli, G.; Lyons, L.; Magnan, A. -M.; Marrouche, J.; Mathias, B.; Nandi, R.; Nash, J.; Nikitenko, A.; Pela, J.; Pesaresi, M.; Petridis, K.; Pioppi, M.; Raymond, D. M.; Rogerson, S.; Rose, A.; Ryan, M. J.; Seez, C.; Sharp, P.; Sparrow, A.; Stoye, M.; Tapper, A.; Vazquez Acosta, M.; Virdee, T.; Wakefield, S.; Wardle, N.; Whyntie, T.; Chadwick, M.; Cole, J. E.; Hobson, P. R.; Khan, A.; Kyberd, P.; Leggat, D.; Leslie, D.; Martin, W.; Reid, I. D.; Symonds, P.; Teodorescu, L.; Turner, M.; Hatakeyama, K.; Liu, H.; Scarborough, T.; Charaf, O.; Henderson, C.; Rumerio, P.; Avetisyan, A.; Bose, T.; Fantasia, C.; Heister, A.; St. John, J.; Lawson, P.; Lazic, D.; Rohlf, J.; Sperka, D.; Sulak, L.; Alimena, J.; Bhattacharya, S.; Christopher, G.; Cutts, D.; Demiragli, Z.; Ferapontov, A.; Garabedian, A.; Heintz, U.; Jabeen, S.; Kukartsev, G.; Laird, E.; Landsberg, G.; Luk, M.; Narain, M.; Nguyen, D.; Segala, M.; Sinthuprasith, T.; Speer, T.; Breedon, R.; Breto, G.; Calderon De La Barca Sanchez, M.; Chauhan, S.; Chertok, M.; Conway, J.; Conway, R.; Cox, P. T.; Dolen, J.; Erbacher, R.; Gardner, M.; Houtz, R.; Ko, W.; Kopecky, A.; Lander, R.; Mall, O.; Miceli, T.; Pellett, D.; Ricci-Tam, F.; Rutherford, B.; Searle, M.; Smith, J.; Squires, M.; Tripathi, M.; Vasquez Sierra, R.; Yohay, R.; Andreev, V.; Cline, D.; Cousins, R.; Duris, J.; Erhan, S.; Everaerts, P.; Farrell, C.; Hauser, J.; Ignatenko, M.; Jarvis, C.; Rakness, G.; Schlein, P.; Traczyk, P.; Valuev, V.; Weber, M.; Babb, J.; Clare, R.; Dinardo, M. E.; Ellison, J.; Gary, J. W.; Giordano, F.; Hanson, G.; Liu, H.; Long, O. R.; Luthra, A.; Nguyen, H.; Paramesvaran, S.; Sturdy, J.; Sumowidagdo, S.; Wilken, R.; Wimpenny, S.; Andrews, W.; Branson, J. G.; Cerati, G. B.; Cittolin, S.; Evans, D.; Holzner, A.; Kelley, R.; Lebourgeois, M.; Letts, J.; Macneill, I.; Mangano, B.; Padhi, S.; Palmer, C.; Petrucciani, G.; Pieri, M.; Sani, M.; Sharma, V.; Simon, S.; Sudano, E.; Tadel, M.; Tu, Y.; Vartak, A.; Wasserbaech, S.; Würthwein, F.; Yagil, A.; Yoo, J.; Barge, D.; Bellan, R.; Campagnari, C.; D’Alfonso, M.; Danielson, T.; Flowers, K.; Geffert, P.; Golf, F.; Incandela, J.; Justus, C.; Kalavase, P.; Kovalskyi, D.; Krutelyov, V.; Lowette, S.; Magaña Villalba, R.; Mccoll, N.; Pavlunin, V.; Ribnik, J.; Richman, J.; Rossin, R.; Stuart, D.; To, W.; West, C.; Apresyan, A.; Bornheim, A.; Chen, Y.; Di Marco, E.; Duarte, J.; Gataullin, M.; Ma, Y.; Mott, A.; Newman, H. B.; Rogan, C.; Spiropulu, M.; Timciuc, V.; Veverka, J.; Wilkinson, R.; Xie, S.; Yang, Y.; Zhu, R. Y.; Azzolini, V.; Calamba, A.; Carroll, R.; Ferguson, T.; Iiyama, Y.; Jang, D. W.; Liu, Y. F.; Paulini, M.; Vogel, H.; Vorobiev, I.; Cumalat, J. P.; Drell, B. R.; Ford, W. T.; Gaz, A.; Luiggi Lopez, E.; Smith, J. G.; Stenson, K.; Ulmer, K. A.; Wagner, S. R.; Alexander, J.; Chatterjee, A.; Eggert, N.; Gibbons, L. K.; Heltsley, B.; Hopkins, W.; Khukhunaishvili, A.; Kreis, B.; Mirman, N.; Nicolas Kaufman, G.; Patterson, J. R.; Ryd, A.; Salvati, E.; Sun, W.; Teo, W. D.; Thom, J.; Thompson, J.; Tucker, J.; Vaughan, J.; Weng, Y.; Winstrom, L.; Wittich, P.; Winn, D.; Abdullin, S.; Albrow, M.; Anderson, J.; Bauerdick, L. A. T.; Beretvas, A.; Berryhill, J.; Bhat, P. C.; Burkett, K.; Butler, J. N.; Chetluru, V.; Cheung, H. W. K.; Chlebana, F.; Elvira, V. D.; Fisk, I.; Freeman, J.; Gao, Y.; Green, D.; Gutsche, O.; Hanlon, J.; Harris, R. M.; Hirschauer, J.; Hooberman, B.; Jindariani, S.; Johnson, M.; Joshi, U.; Klima, B.; Kunori, S.; Kwan, S.; Leonidopoulos, C.; Linacre, J.; Lincoln, D.; Lipton, R.; Lykken, J.; Maeshima, K.; Marraffino, J. M.; Maruyama, S.; Mason, D.; McBride, P.; Mishra, K.; Mrenna, S.; Musienko, Y.; Newman-Holmes, C.; O’Dell, V.; Prokofyev, O.; Sexton-Kennedy, E.; Sharma, S.; Spalding, W. J.; Spiegel, L.; Taylor, L.; Tkaczyk, S.; Tran, N. V.; Uplegger, L.; Vaandering, E. W.; Vidal, R.; Whitmore, J.; Wu, W.; Yang, F.; Yun, J. C.; Acosta, D.; Avery, P.; Bourilkov, D.; Chen, M.; Cheng, T.; Das, S.; De Gruttola, M.; Di Giovanni, G. P.; Dobur, D.; Drozdetskiy, A.; Field, R. D.; Fisher, M.; Fu, Y.; Furic, I. K.; Gartner, J.; Hugon, J.; Kim, B.; Konigsberg, J.; Korytov, A.; Kropivnitskaya, A.; Kypreos, T.; Low, J. F.; Matchev, K.; Milenovic, P.; Mitselmakher, G.; Muniz, L.; Park, M.; Remington, R.; Rinkevicius, A.; Sellers, P.; Skhirtladze, N.; Snowball, M.; Yelton, J.; Zakaria, M.; Gaultney, V.; Hewamanage, S.; Lebolo, L. M.; Linn, S.; Markowitz, P.; Martinez, G.; Rodriguez, J. L.; Adams, T.; Askew, A.; Bochenek, J.; Chen, J.; Diamond, B.; Gleyzer, S. V.; Haas, J.; Hagopian, S.; Hagopian, V.; Jenkins, M.; Johnson, K. F.; Prosper, H.; Veeraraghavan, V.; Weinberg, M.; Baarmand, M. M.; Dorney, B.; Hohlmann, M.; Kalakhety, H.; Vodopiyanov, I.; Yumiceva, F.; Adams, M. R.; Anghel, I. M.; Apanasevich, L.; Bai, Y.; Bazterra, V. E.; Betts, R. R.; Bucinskaite, I.; Callner, J.; Cavanaugh, R.; Evdokimov, O.; Gauthier, L.; Gerber, C. E.; Hofman, D. J.; Khalatyan, S.; Lacroix, F.; O’Brien, C.; Silkworth, C.; Strom, D.; Turner, P.; Varelas, N.; Akgun, U.; Albayrak, E. A.; Bilki, B.; Clarida, W.; Duru, F.; Griffiths, S.; Merlo, J. -P.; Mermerkaya, H.; Mestvirishvili, A.; Moeller, A.; Nachtman, J.; Newsom, C. R.; Norbeck, E.; Onel, Y.; Ozok, F.; Sen, S.; Tan, P.; Tiras, E.; Wetzel, J.; Yetkin, T.; Yi, K.; Barnett, B. A.; Blumenfeld, B.; Bolognesi, S.; Fehling, D.; Giurgiu, G.; Gritsan, A. V.; Guo, Z. J.; Hu, G.; Maksimovic, P.; Swartz, M.; Whitbeck, A.; Baringer, P.; Bean, A.; Benelli, G.; Kenny, R. P.; Murray, M.; Noonan, D.; Sanders, S.; Stringer, R.; Tinti, G.; Wood, J. S.; Barfuss, A. F.; Bolton, T.; Chakaberia, I.; Ivanov, A.; Khalil, S.; Makouski, M.; Maravin, Y.; Shrestha, S.; Svintradze, I.; Gronberg, J.; Lange, D.; Rebassoo, F.; Wright, D.; Baden, A.; Calvert, B.; Eno, S. C.; Gomez, J. A.; Hadley, N. J.; Kellogg, R. G.; Kirn, M.; Kolberg, T.; Lu, Y.; Marionneau, M.; Mignerey, A. C.; Pedro, K.; Skuja, A.; Temple, J.; Tonjes, M. B.; Tonwar, S. C.; Apyan, A.; Bauer, G.; Bendavid, J.; Busza, W.; Butz, E.; Cali, I. A.; Chan, M.; Dutta, V.; Gomez Ceballos, G.; Goncharov, M.; Kim, Y.; Klute, M.; Krajczar, K.; Levin, A.; Luckey, P. D.; Ma, T.; Nahn, S.; Paus, C.; Ralph, D.; Roland, C.; Roland, G.; Rudolph, M.; Stephans, G. S. F.; Stöckli, F.; Sumorok, K.; Sung, K.; Velicanu, D.; Wenger, E. A.; Wolf, R.; Wyslouch, B.; Yang, M.; Yilmaz, Y.; Yoon, A. S.; Zanetti, M.; Zhukova, V.; Cooper, S. I.; Dahmes, B.; De Benedetti, A.; Franzoni, G.; Gude, A.; Kao, S. C.; Klapoetke, K.; Kubota, Y.; Mans, J.; Pastika, N.; Rusack, R.; Sasseville, M.; Singovsky, A.; Tambe, N.; Turkewitz, J.; Cremaldi, L. M.; Kroeger, R.; Perera, L.; Rahmat, R.; Sanders, D. A.; Avdeeva, E.; Bloom, K.; Bose, S.; Claes, D. R.; Dominguez, A.; Eads, M.; Keller, J.; Kravchenko, I.; Lazo-Flores, J.; Malik, S.; Snow, G. R.; Godshalk, A.; Iashvili, I.; Jain, S.; Kharchilava, A.; Kumar, A.; Rappoccio, S.; Alverson, G.; Barberis, E.; Baumgartel, D.; Chasco, M.; Haley, J.; Nash, D.; Orimoto, T.; Trocino, D.; Wood, D.; Zhang, J.; Anastassov, A.; Hahn, K. A.; Kubik, A.; Lusito, L.; Mucia, N.; Odell, N.; Ofierzynski, R. A.; Pollack, B.; Pozdnyakov, A.; Schmitt, M.; Stoynev, S.; Velasco, M.; Won, S.; Antonelli, L.; Berry, D.; Brinkerhoff, A.; Chan, K. M.; Hildreth, M.; Jessop, C.; Karmgard, D. J.; Kolb, J.; Lannon, K.; Luo, W.; Lynch, S.; Marinelli, N.; Morse, D. M.; Pearson, T.; Planer, M.; Ruchti, R.; Slaunwhite, J.; Valls, N.; Wayne, M.; Wolf, M.; Bylsma, B.; Durkin, L. S.; Hill, C.; Hughes, R.; Kotov, K.; Ling, T. Y.; Puigh, D.; Rodenburg, M.; Vuosalo, C.; Williams, G.; Winer, B. L.; Berry, E.; Elmer, P.; Halyo, V.; Hebda, P.; Hegeman, J.; Hunt, A.; Jindal, P.; Koay, S. A.; Lopes Pegna, D.; Lujan, P.; Marlow, D.; Medvedeva, T.; Mooney, M.; Olsen, J.; Piroué, P.; Quan, X.; Raval, A.; Saka, H.; Stickland, D.; Tully, C.; Werner, J. S.; Zuranski, A.; Brownson, E.; Lopez, A.; Mendez, H.; Ramirez Vargas, J. E.; Alagoz, E.; Barnes, V. E.; Benedetti, D.; Bolla, G.; Bortoletto, D.; De Mattia, M.; Everett, A.; Hu, Z.; Jones, M.; Koybasi, O.; Kress, M.; Laasanen, A. T.; Leonardo, N.; Maroussov, V.; Merkel, P.; Miller, D. H.; Neumeister, N.; Shipsey, I.; Silvers, D.; Svyatkovskiy, A.; Vidal Marono, M.; Yoo, H. D.; Zablocki, J.; Zheng, Y.; Guragain, S.; Parashar, N.; Adair, A.; Akgun, B.; Boulahouache, C.; Ecklund, K. M.; Geurts, F. J. M.; Li, W.; Padley, B. P.; Redjimi, R.; Roberts, J.; Zabel, J.; Betchart, B.; Bodek, A.; Chung, Y. S.; Covarelli, R.; de Barbaro, P.; Demina, R.; Eshaq, Y.; Ferbel, T.; Garcia-Bellido, A.; Goldenzweig, P.; Han, J.; Harel, A.; Miner, D. C.; Vishnevskiy, D.; Zielinski, M.; Bhatti, A.; Ciesielski, R.; Demortier, L.; Goulianos, K.; Lungu, G.; Malik, S.; Mesropian, C.; Arora, S.; Barker, A.; Chou, J. P.; Contreras-Campana, C.; Contreras-Campana, E.; Duggan, D.; Ferencek, D.; Gershtein, Y.; Gray, R.; Halkiadakis, E.; Hidas, D.; Lath, A.; Panwalkar, S.; Park, M.; Patel, R.; Rekovic, V.; Robles, J.; Rose, K.; Salur, S.; Schnetzer, S.; Seitz, C.; Somalwar, S.; Stone, R.; Thomas, S.; Walker, M.; Cerizza, G.; Hollingsworth, M.; Spanier, S.; Yang, Z. C.; York, A.; Eusebi, R.; Flanagan, W.; Gilmore, J.; Kamon, T.; Khotilovich, V.; Montalvo, R.; Osipenkov, I.; Pakhotin, Y.; Perloff, A.; Roe, J.; Safonov, A.; Sakuma, T.; Sengupta, S.; Suarez, I.; Tatarinov, A.; Toback, D.; Akchurin, N.; Damgov, J.; Dragoiu, C.; Dudero, P. R.; Jeong, C.; Kovitanggoon, K.; Lee, S. W.; Libeiro, T.; Volobouev, I.; Appelt, E.; Delannoy, A. G.; Florez, C.; Greene, S.; Gurrola, A.; Johns, W.; Kurt, P.; Maguire, C.; Melo, A.; Sharma, M.; Sheldon, P.; Snook, B.; Tuo, S.; Velkovska, J.; Arenton, M. W.; Balazs, M.; Boutle, S.; Cox, B.; Francis, B.; Goodell, J.; Hirosky, R.; Ledovskoy, A.; Lin, C.; Neu, C.; Wood, J.; Gollapinni, S.; Harr, R.; Karchin, P. E.; Kottachchi Kankanamge Don, C.; Lamichhane, P.; Sakharov, A.; Anderson, M.; Belknap, D. A.; Borrello, L.; Carlsmith, D.; Cepeda, M.; Dasu, S.; Friis, E.; Gray, L.; Grogg, K. S.; Grothe, M.; Hall-Wilton, R.; Herndon, M.; Hervé, A.; Klabbers, P.; Klukas, J.; Lanaro, A.; Lazaridis, C.; Loveless, R.; Mohapatra, A.; Ojalvo, I.; Palmonari, F.; Pierro, G. A.; Ross, I.; Savin, A.; Smith, W. H.; Swanson, J.

    2013-09-01

    The results of searches for supersymmetry by the CMS experiment are interpreted in the framework of simplified models. The results are based on data corresponding to an integrated luminosity of 4.73 to 4.98 inverse femtobarns. The data were collected at the LHC in proton-proton collisions at a center-of-mass energy of 7 TeV. This paper describes the method of interpretation and provides upper limits on the product of the production cross section and branching fraction as a function of new particle masses for a number of simplified models. These limits and the corresponding experimental acceptance calculations can be used to constrain other theoretical models and to compare different supersymmetry-inspired analyses.

  9. Model and experiments to optimize co-adaptation in a simplified myoelectric control system.

    Science.gov (United States)

    Couraud, M; Cattaert, D; Paclet, F; Oudeyer, P Y; de Rugy, A

    2018-04-01

    To compensate for a limb lost in an amputation, myoelectric prostheses use surface electromyography (EMG) from the remaining muscles to control the prosthesis. Despite considerable progress, myoelectric controls remain markedly different from the way we normally control movements, and require intense user adaptation. To overcome this, our goal is to explore concurrent machine co-adaptation techniques that are developed in the field of brain-machine interface, and that are beginning to be used in myoelectric controls. We combined a simplified myoelectric control with a perturbation for which human adaptation is well characterized and modeled, in order to explore co-adaptation settings in a principled manner. First, we reproduced results obtained in a classical visuomotor rotation paradigm in our simplified myoelectric context, where we rotate the muscle pulling vectors used to reconstruct wrist force from EMG. Then, a model of human adaptation in response to directional error was used to simulate various co-adaptation settings, where perturbations and machine co-adaptation are both applied on muscle pulling vectors. These simulations established that a relatively low gain of machine co-adaptation that minimizes final errors generates slow and incomplete adaptation, while higher gains increase adaptation rate but also errors by amplifying noise. After experimental verification on real subjects, we tested a variable gain that cumulates the advantages of both, and implemented it with directionally tuned neurons similar to those used to model human adaptation. This enables machine co-adaptation to locally improve myoelectric control, and to absorb more challenging perturbations. The simplified context used here enabled to explore co-adaptation settings in both simulations and experiments, and to raise important considerations such as the need for a variable gain encoded locally. The benefits and limits of extending this approach to more complex and functional

  10. Model and experiments to optimize co-adaptation in a simplified myoelectric control system

    Science.gov (United States)

    Couraud, M.; Cattaert, D.; Paclet, F.; Oudeyer, P. Y.; de Rugy, A.

    2018-04-01

    Objective. To compensate for a limb lost in an amputation, myoelectric prostheses use surface electromyography (EMG) from the remaining muscles to control the prosthesis. Despite considerable progress, myoelectric controls remain markedly different from the way we normally control movements, and require intense user adaptation. To overcome this, our goal is to explore concurrent machine co-adaptation techniques that are developed in the field of brain-machine interface, and that are beginning to be used in myoelectric controls. Approach. We combined a simplified myoelectric control with a perturbation for which human adaptation is well characterized and modeled, in order to explore co-adaptation settings in a principled manner. Results. First, we reproduced results obtained in a classical visuomotor rotation paradigm in our simplified myoelectric context, where we rotate the muscle pulling vectors used to reconstruct wrist force from EMG. Then, a model of human adaptation in response to directional error was used to simulate various co-adaptation settings, where perturbations and machine co-adaptation are both applied on muscle pulling vectors. These simulations established that a relatively low gain of machine co-adaptation that minimizes final errors generates slow and incomplete adaptation, while higher gains increase adaptation rate but also errors by amplifying noise. After experimental verification on real subjects, we tested a variable gain that cumulates the advantages of both, and implemented it with directionally tuned neurons similar to those used to model human adaptation. This enables machine co-adaptation to locally improve myoelectric control, and to absorb more challenging perturbations. Significance. The simplified context used here enabled to explore co-adaptation settings in both simulations and experiments, and to raise important considerations such as the need for a variable gain encoded locally. The benefits and limits of extending this

  11. Statistical methods for assays with limits of detection: Serum bile acid as a differentiator between patients with normal colons, adenomas, and colorectal cancer

    Directory of Open Access Journals (Sweden)

    Bonnie LaFleur

    2011-01-01

    Full Text Available In analytic chemistry a detection limit (DL is the lowest measurable amount of an analyte that can be distinguished from a blank; many biomedical measurement technologies exhibit this property. From a statistical perspective, these data present inferential challenges because instead of precise measures, one only has information that the value is somewhere between 0 and the DL (below detection limit, BDL. Substitution of BDL values, with 0 or the DL can lead to biased parameter estimates and a loss of statistical power. Statistical methods that make adjustments when dealing with these types of data, often called left-censored data, are available in many commercial statistical packages. Despite this availability, the use of these methods is still not widespread in biomedical literature. We have reviewed the statistical approaches of dealing with BDL values, and used simulations to examine the performance of the commonly used substitution methods and the most widely available statistical methods. We have illustrated these methods using a study undertaken at the Vanderbilt-Ingram Cancer Center, to examine the serum bile acid levels in patients with colorectal cancer and adenoma. We have found that the modern methods for BDL values identify disease-related differences that are often missed, with statistically naive approaches.

  12. Simplified Stability Criteria for Delayed Neutral Systems

    Directory of Open Access Journals (Sweden)

    Xinghua Zhang

    2014-01-01

    Full Text Available For a class of linear time-invariant neutral systems with neutral and discrete constant delays, several existing asymptotic stability criteria in the form of linear matrix inequalities (LMIs are simplified by using matrix analysis techniques. Compared with the original stability criteria, the simplified ones include fewer LMI variables, which can obviously reduce computational complexity. Simultaneously, it is theoretically shown that the simplified stability criteria and original ones are equivalent; that is, they have the same conservativeness. Finally, a numerical example is employed to verify the theoretic results investigated in this paper.

  13. Utilization of handheld computing to simplify compliance

    International Nuclear Information System (INIS)

    Galvin, G.; Rasmussen, J.; Haines, A.

    2008-01-01

    Monitoring job site performance and building a continually improving organization is an ongoing challenge for operators of process and power generation facilities. Stakeholders need to accurately capture records of quality and safety compliance, job progress, and operational experiences (OPEX). This paper explores the use of technology-enabled processes as a means for simplifying compliance to quality, safety, administrative, maintenance and operations activities. The discussion will explore a number of emerging technologies and their application to simplifying task execution and process compliance. This paper will further discuss methodologies to further refine processes through trending improvements in compliance and continually optimizing and simplifying through the use of technology. (author)

  14. The normal limits, subclinical significance, related metabolic derangements and distinct biological effects of body site-specific adiposity in relatively healthy population.

    Directory of Open Access Journals (Sweden)

    Chun-Ho Yun

    Full Text Available BACKGROUND: The accumulation of visceral adipose tissue that occurs with normal aging is associated with increased cardiovascular risks. However, the clinical significance, biological effects, and related cardiometabolic derangements of body-site specific adiposity in a relatively healthy population have not been well characterized. MATERIALS AND METHODS: In this cross-sectional study, we consecutively enrolled 608 asymptomatic subjects (mean age: 47.3 years, 27% female from 2050 subjects undergoing an annual health survey in Taiwan. We measured pericardial (PCF and thoracic peri-aortic (TAT adipose tissue volumes by 16-slice multi-detector computed tomography (MDCT (Aquarius 3D Workstation, TeraRecon, San Mateo, CA, USA and related these to clinical characteristics, body fat composition (Tanita 305 Corporation, Tokyo, Japan, coronary calcium score (CCS, serum insulin, high-sensitivity C-reactive protein (Hs-CRP level and circulating leukocytes count. Metabolic risk was scored by Adult Treatment Panel III guidelines. RESULTS: TAT, PCF, and total body fat composition all increased with aging and higher metabolic scores (all p<0.05. Only TAT, however, was associated with higher circulating leukocyte counts (ß-coef.:0.24, p<0.05, serum insulin (ß-coef.:0.17, p<0.05 and high sensitivity C-reactive protein (ß-coef.:0.24, p<0.05. These relationships persisted after adjustment in multivariable models (all p<0.05. A TAT volume of 8.29 ml yielded the largest area under the receiver operating characteristic curve (AUROC: 0.79, 95%CI: 0.74-0.83 to identify metabolic syndrome. TAT but not PCF correlated with higher coronary calcium score after adjustment for clinical variables (all p<0.05. CONCLUSION: In our study, we observe that age-related body-site specific accumulation of adipose tissue may have distinct biological effects. Compared to other adiposity measures, peri-aortic adiposity is more tightly associated with cardiometabolic risk profiles and

  15. Simplified dose calculation method for mantle technique

    International Nuclear Information System (INIS)

    Scaff, L.A.M.

    1984-01-01

    A simplified dose calculation method for mantle technique is described. In the routine treatment of lymphom as using this technique, the daily doses at the midpoints at five anatomical regions are different because the thicknesses are not equal. (Author) [pt

  16. A simplified technique for nasoendotracheal tube immobilization.

    OpenAIRE

    Berardo, N.; Leban, S. G.; Williams, F. A.

    1989-01-01

    A simplified technique for immobilization of a nasoendotracheal tube is described in which a wide strap of open cell, hypoallergenic, foam-backed fabric is secured to the patient's head with a Velcro fastener.

  17. Simplified Models for LHC New Physics Searches

    International Nuclear Information System (INIS)

    Alves, Daniele; Arkani-Hamed, Nima; Arora, Sanjay; Bai, Yang; Baumgart, Matthew; Berger, Joshua; Butler, Bart; Chang, Spencer; Cheng, Hsin-Chia; Cheung, Clifford; Chivukula, R. Sekhar; Cho, Won Sang; Cotta, Randy; D'Alfonso, Mariarosaria; El Hedri, Sonia; Essig, Rouven; Fitzpatrick, Liam; Fox, Patrick; Franceschini, Roberto

    2012-01-01

    This document proposes a collection of simplified models relevant to the design of new-physics searches at the LHC and the characterization of their results. Both ATLAS and CMS have already presented some results in terms of simplified models, and we encourage them to continue and expand this effort, which supplements both signature-based results and benchmark model interpretations. A simplified model is defined by an effective Lagrangian describing the interactions of a small number of new particles. Simplified models can equally well be described by a small number of masses and cross-sections. These parameters are directly related to collider physics observables, making simplified models a particularly effective framework for evaluating searches and a useful starting point for characterizing positive signals of new physics. This document serves as an official summary of the results from the 'Topologies for Early LHC Searches' workshop, held at SLAC in September of 2010, the purpose of which was to develop a set of representative models that can be used to cover all relevant phase space in experimental searches. Particular emphasis is placed on searches relevant for the first ∼ 50-500 pb -1 of data and those motivated by supersymmetric models. This note largely summarizes material posted at http://lhcnewphysics.org/, which includes simplified model definitions, Monte Carlo material, and supporting contacts within the theory community. We also comment on future developments that may be useful as more data is gathered and analyzed by the experiments.

  18. Simplified Models for LHC New Physics Searches

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Daniele; /SLAC; Arkani-Hamed, Nima; /Princeton, Inst. Advanced Study; Arora, Sanjay; /Rutgers U., Piscataway; Bai, Yang; /SLAC; Baumgart, Matthew; /Johns Hopkins U.; Berger, Joshua; /Cornell U., Phys. Dept.; Buckley, Matthew; /Fermilab; Butler, Bart; /SLAC; Chang, Spencer; /Oregon U. /UC, Davis; Cheng, Hsin-Chia; /UC, Davis; Cheung, Clifford; /UC, Berkeley; Chivukula, R.Sekhar; /Michigan State U.; Cho, Won Sang; /Tokyo U.; Cotta, Randy; /SLAC; D' Alfonso, Mariarosaria; /UC, Santa Barbara; El Hedri, Sonia; /SLAC; Essig, Rouven, (ed.); /SLAC; Evans, Jared A.; /UC, Davis; Fitzpatrick, Liam; /Boston U.; Fox, Patrick; /Fermilab; Franceschini, Roberto; /LPHE, Lausanne /Pittsburgh U. /Argonne /Northwestern U. /Rutgers U., Piscataway /Rutgers U., Piscataway /Carleton U. /CERN /UC, Davis /Wisconsin U., Madison /SLAC /SLAC /SLAC /Rutgers U., Piscataway /Syracuse U. /SLAC /SLAC /Boston U. /Rutgers U., Piscataway /Seoul Natl. U. /Tohoku U. /UC, Santa Barbara /Korea Inst. Advanced Study, Seoul /Harvard U., Phys. Dept. /Michigan U. /Wisconsin U., Madison /Princeton U. /UC, Santa Barbara /Wisconsin U., Madison /Michigan U. /UC, Davis /SUNY, Stony Brook /TRIUMF; /more authors..

    2012-06-01

    This document proposes a collection of simplified models relevant to the design of new-physics searches at the LHC and the characterization of their results. Both ATLAS and CMS have already presented some results in terms of simplified models, and we encourage them to continue and expand this effort, which supplements both signature-based results and benchmark model interpretations. A simplified model is defined by an effective Lagrangian describing the interactions of a small number of new particles. Simplified models can equally well be described by a small number of masses and cross-sections. These parameters are directly related to collider physics observables, making simplified models a particularly effective framework for evaluating searches and a useful starting point for characterizing positive signals of new physics. This document serves as an official summary of the results from the 'Topologies for Early LHC Searches' workshop, held at SLAC in September of 2010, the purpose of which was to develop a set of representative models that can be used to cover all relevant phase space in experimental searches. Particular emphasis is placed on searches relevant for the first {approx} 50-500 pb{sup -1} of data and those motivated by supersymmetric models. This note largely summarizes material posted at http://lhcnewphysics.org/, which includes simplified model definitions, Monte Carlo material, and supporting contacts within the theory community. We also comment on future developments that may be useful as more data is gathered and analyzed by the experiments.

  19. Improved emergency elevated air release for simplified PWR

    International Nuclear Information System (INIS)

    Naitoh, T.; Bruce, R.A.; Hirota, K.; Tajiri, Y.

    1992-01-01

    In developing the application of the simplified PWR in Japan, one of the most important areas is to limit post-accident site boundary whole body dose. In addressing this, the concept of Emergency Passive Air Filtration System (EPAFS) and it's feasibility is developed. The efficiency of charcoal filtering and the atmospheric diffusion effect of an elevated air release are important for dose reduction. The performance of these functions was evaluated by confirmatory testing. The test results confirmed a 99 percent efficiency of charcoal filter and an atmospheric diffusion effect higher than that of a conventional plant. The Emergency Passive Air Filtration System (EPAFS) and the atmospheric diffusion effect of elevated air release contribute to making the calculated post-accident site boundary whole body dose of simplified PWR as low as that of the conventional Japanese PWR plant. (author)

  20. Simplified hydraulic model of French vertical-flow constructed wetlands.

    Science.gov (United States)

    Arias, Luis; Bertrand-Krajewski, Jean-Luc; Molle, Pascal

    2014-01-01

    Designing vertical-flow constructed wetlands (VFCWs) to treat both rain events and dry weather flow is a complex task due to the stochastic nature of rain events. Dynamic models can help to improve design, but they usually prove difficult to handle for designers. This study focuses on the development of a simplified hydraulic model of French VFCWs using an empirical infiltration coefficient--infiltration capacity parameter (ICP). The model was fitted using 60-second-step data collected on two experimental French VFCW systems and compared with Hydrus 1D software. The model revealed a season-by-season evolution of the ICP that could be explained by the mechanical role of reeds. This simplified model makes it possible to define time-course shifts in ponding time and outlet flows. As ponding time hinders oxygen renewal, thus impacting nitrification and organic matter degradation, ponding time limits can be used to fix a reliable design when treating both dry and rain events.

  1. Birkhoff normalization

    NARCIS (Netherlands)

    Broer, H.; Hoveijn, I.; Lunter, G.; Vegter, G.

    2003-01-01

    The Birkhoff normal form procedure is a widely used tool for approximating a Hamiltonian systems by a simpler one. This chapter starts out with an introduction to Hamiltonian mechanics, followed by an explanation of the Birkhoff normal form procedure. Finally we discuss several algorithms for

  2. Limiting oxygen concentration for extinction of upward spreading flames over inclined thin polyethylene-insulated NiCr electrical wires with opposed-flow under normal- and micro-gravity

    KAUST Repository

    Hu, Longhua

    2016-10-02

    Materials, such as electrical wire, used in spacecraft must pass stringent fire safety standards. Tests for such standards are typically performed under normal gravity conditions and then extended to applications under microgravity conditions. The experiments reported here used polyethylene (PE)-insulated (thickness of 0.15 mm) Nichrome (NiCr)-core (diameter of 0.5 mm) electrical wires. Limiting oxygen concentrations (LOC) at extinction were measured for upward spreading flame at various forced opposed-flow (downward) speeds (0−25 cm/s) at several inclination angles (0−75°) under normal gravity conditions. The differences from those previously obtained under microgravity conditions were quantified and correlated to provide a reference for the development of fire safety test standards for electrical wires to be used in space exploration. It was found that as the opposed-flow speed increased for a specified inclination angle (except the horizontal case), LOC first increased, then decreased and finally increased again. The first local maximum of this LOC variation corresponded to a critical forced flow speed resulted from the change in flame spread pattern from concurrent to counter-current type. This critical forced flow speed correlated well with the buoyancy-induced flow speed component in the wire\\'s direction when the flame base width along the wire was used as a characteristic length scale. LOC was generally higher under the normal gravity than under the microgravity and the difference between the two decreased as the opposed-flow speed increases, following a reasonably linear trend at relatively higher flow speeds (over 10 cm/s). The decrease in the difference in LOC under normal- and microgravity conditions as the opposed-flow speed increases correlated well with the gravity acceleration component in the wire\\'s direction, providing a measure to extend LOC determined by the tests under normal gravity conditions (at various inclination angles and opposed

  3. [Simplified laparoscopic gastric bypass. Initial experience].

    Science.gov (United States)

    Hernández-Miguelena, Luis; Maldonado-Vázquez, Angélica; Cortes-Romano, Pablo; Ríos-Cruz, Daniel; Marín-Domínguez, Raúl; Castillo-González, Armando

    2014-01-01

    Obesity surgery includes various gastrointestinal procedures. Roux-en-Y gastric bypass is the prototype of mixed procedures being the most practiced worldwide. A similar and novel technique has been adopted by Dr. Almino Cardoso Ramos and Dr. Manoel Galvao called "simplified bypass," which has been accepted due to the greater ease and very similar results to the conventional technique. The aim of this study is to describe the results of the simplified gastric bypass for treatment of morbid obesity in our institution. We performed a descriptive, retrospective study of all patients undergoing simplified gastric bypass from January 2008 to July 2012 in the obesity clinic of a private hospital in Mexico City. A total of 90 patients diagnosed with morbid obesity underwent simplified gastric bypass. Complications occurred in 10% of patients; these were more frequent bleeding and internal hernia. Mortality in the study period was 0%. The average weight loss at 12 months was 72.7%. Simplified gastric bypass surgery is safe with good mid-term results and a loss of adequate weight in 71% of cases.

  4. Proliferation and the Civilian Nuclear Fuel Cycle. Towards a Simplified Recipe to Measure Proliferation Risk

    Energy Technology Data Exchange (ETDEWEB)

    Brogli, R.; Krakowski, R.A

    2001-08-01

    The primary goal of this study is to frame the problem of nuclear proliferation in the context of protection and risks associated with nuclear materials flowing in the civilian nuclear fuel cycle. The perspective adopted for this study is that of a nuclear utility and the flow of fresh and spent nuclear fuel with which that utility must deal in the course of providing economic, safe, and ecologically acceptable electrical power to the public. Within this framework quantitative approaches to a material-dependent, simplified proliferation-risk metric are identified and explored. The driving force behind this search for such a proliferation metric derives from the need to quantify the proliferation risk in the context of evaluating various commercial nuclear fuel cycle options (e.g., plutonium recycle versus once-through). While the formulation of the algebra needed to describe the desired, simplified metric(s) should be straight forward once a modus operandi is defined, considerable interaction with the user of any final product that results is essential. Additionally, a broad contextual review of the proliferation problem and past efforts in the quantification of associated risks was developed as part of this study. This extensive review was essential to setting perspectives and establishing (feasibility) limits to the search for a proliferation metric(s) that meets the goals of this study. Past analyses of proliferation risks associated with the commercial nuclear fuel cycle have generally been based on a range of decision-analysis, operations-research tools. Within the time and budget constraints, as well as the self-enforced (utility) customer focus, the more subjective and data-intensive decision-analysis methodologies where not pursued. Three simplified, less-subjective approaches were investigated instead: a) a simplified 'four-factor' formula expressing as a normalized product political, material-quantity, material-quality, and material

  5. Proliferation and the Civilian Nuclear Fuel Cycle. Towards a Simplified Recipe to Measure Proliferation Risk

    International Nuclear Information System (INIS)

    Brogli, R.; Krakowski, R.A.

    2001-08-01

    The primary goal of this study is to frame the problem of nuclear proliferation in the context of protection and risks associated with nuclear materials flowing in the civilian nuclear fuel cycle. The perspective adopted for this study is that of a nuclear utility and the flow of fresh and spent nuclear fuel with which that utility must deal in the course of providing economic, safe, and ecologically acceptable electrical power to the public. Within this framework quantitative approaches to a material-dependent, simplified proliferation-risk metric are identified and explored. The driving force behind this search for such a proliferation metric derives from the need to quantify the proliferation risk in the context of evaluating various commercial nuclear fuel cycle options (e.g., plutonium recycle versus once-through). While the formulation of the algebra needed to describe the desired, simplified metric(s) should be straight forward once a modus operandi is defined, considerable interaction with the user of any final product that results is essential. Additionally, a broad contextual review of the proliferation problem and past efforts in the quantification of associated risks was developed as part of this study. This extensive review was essential to setting perspectives and establishing (feasibility) limits to the search for a proliferation metric(s) that meets the goals of this study. Past analyses of proliferation risks associated with the commercial nuclear fuel cycle have generally been based on a range of decision-analysis, operations-research tools. Within the time and budget constraints, as well as the self-enforced (utility) customer focus, the more subjective and data-intensive decision-analysis methodologies where not pursued. Three simplified, less-subjective approaches were investigated instead: a) a simplified 'four-factor' formula expressing as a normalized product political, material-quantity, material-quality, and material-protection metrics; b

  6. Development of long operating cycle simplified BWR

    International Nuclear Information System (INIS)

    Heki, H.; Nakamaru, M.; Maruya, T.; Hiraiwa, K.; Arai, K.; Narabayash, T.; Aritomi, M.

    2002-01-01

    This paper describes an innovative plant concept for long operating cycle simplified BWR (LSBWR) In this plant concept, 1) Long operating cycle ( 3 to 15 years), 2) Simplified systems and building, 3) Factory fabrication in module are discussed. Designing long operating core is based on medium enriched U-235 with burnable poison. Simplified systems and building are realized by using natural circulation with bottom located core, internal CRD and PCV with passive system and an integrated reactor and turbine building. This LSBWR concept will have make high degree of safety by IVR (In Vessel Retention) capability, large water inventory above the core region and no PCV vent to the environment due to PCCS (Passive Containment Cooling System) and internal vent tank. Integrated building concept could realize highly modular arrangement in hull structure (ship frame structure), ease of seismic isolation capability and high applicability of standardization and factory fabrication. (authors)

  7. Hypersonic Vehicle Propulsion System Simplified Model Development

    Science.gov (United States)

    Stueber, Thomas J.; Raitano, Paul; Le, Dzu K.; Ouzts, Peter

    2007-01-01

    This document addresses the modeling task plan for the hypersonic GN&C GRC team members. The overall propulsion system modeling task plan is a multi-step process and the task plan identified in this document addresses the first steps (short term modeling goals). The procedures and tools produced from this effort will be useful for creating simplified dynamic models applicable to a hypersonic vehicle propulsion system. The document continues with the GRC short term modeling goal. Next, a general description of the desired simplified model is presented along with simulations that are available to varying degrees. The simulations may be available in electronic form (FORTRAN, CFD, MatLab,...) or in paper form in published documents. Finally, roadmaps outlining possible avenues towards realizing simplified model are presented.

  8. Simplified design of switching power supplies

    CERN Document Server

    Lenk, John

    1995-01-01

    * Describes the operation of each circuit in detail * Examines a wide selection of external components that modify the IC package characteristics * Provides hands-on, essential information for designing a switching power supply Simplified Design of Switching Power Supplies is an all-inclusive, one-stop guide to switching power-supply design. Step-by-step instructions and diagrams render this book essential for the student and the experimenter, as well as the design professional. Simplified Design of Switching Power Supplies concentrates on the use of IC regulators. All popular forms of swit

  9. Eigenvalues of the simplified ideal MHD ballooning equation

    International Nuclear Information System (INIS)

    Paris, R.B.; Auby, N.; Dagazian, R.Y.

    1986-01-01

    The investigation of the spectrum of the simplified differential equation describing the variation of the amplitude of the ideal MHD ballooning instability along magnetic field lines constitutes a multiparameter Schroedinger eigenvalue problem. An exact eigenvalue relation for the discrete part of the spectrum is obtained in terms of the oblate spheroidal functions. The dependence of the eigenvalues lambda on the two free parameters γ 2 and μ 2 of the equation is discussed, together with certain analytical approximations in the limits of small and large γ 2 . A brief review of the principal properties of the spheroidal functions is given in an appendix

  10. A simplified hazard audit procedures guide

    International Nuclear Information System (INIS)

    Harrison, D.G.; Tabatabai, A.S.; Scott, W.B.; Murphy, K.J.

    1991-02-01

    As part of on-going technical support services to the US Department of Energy (DOE), Battelle Pacific Northwest Laboratory (PNL) has developed a simplified hazard audit procedures guide which enables cost-effective and timely assessment and characterization of the DOE nuclear (reactor and nonreactor) and non-nuclear facilities safety profile

  11. Assessment of average of normals (AON) procedure for outlier-free datasets including qualitative values below limit of detection (LoD): an application within tumor markers such as CA 15-3, CA 125, and CA 19-9.

    Science.gov (United States)

    Usta, Murat; Aral, Hale; Mete Çilingirtürk, Ahmet; Kural, Alev; Topaç, Ibrahim; Semerci, Tuna; Hicri Köseoğlu, Mehmet

    2016-11-01

    Average of normals (AON) is a quality control procedure that is sensitive only to systematic errors that can occur in an analytical process in which patient test results are used. The aim of this study was to develop an alternative model in order to apply the AON quality control procedure to datasets that include qualitative values below limit of detection (LoD). The reported patient test results for tumor markers, such as CA 15-3, CA 125, and CA 19-9, analyzed by two instruments, were retrieved from the information system over a period of 5 months, using the calibrator and control materials with the same lot numbers. The median as a measure of central tendency and the median absolute deviation (MAD) as a measure of dispersion were used for the complementary model of AON quality control procedure. The u bias values, which were determined for the bias component of the measurement uncertainty, were partially linked to the percentages of the daily median values of the test results that fall within the control limits. The results for these tumor markers, in which lower limits of reference intervals are not medically important for clinical diagnosis and management, showed that the AON quality control procedure, using the MAD around the median, can be applied for datasets including qualitative values below LoD.

  12. A simplified model of choice behavior under uncertainty

    Directory of Open Access Journals (Sweden)

    Ching-Hung Lin

    2016-08-01

    Full Text Available The Iowa Gambling Task (IGT has been standardized as a clinical assessment tool (Bechara, 2007. Nonetheless, numerous research groups have attempted to modify IGT models to optimize parameters for predicting the choice behavior of normal controls and patients. A decade ago, most researchers considered the expected utility (EU model (Busemeyer and Stout, 2002 to be the optimal model for predicting choice behavior under uncertainty. However, in recent years, studies have demonstrated the prospect utility (PU models (Ahn et al., 2008 to be more effective than the EU models in the IGT. Nevertheless, after some preliminary tests, we propose that Ahn et al. (2008 PU model is not optimal due to some incompatible results between our behavioral and modeling data. This study aims to modify Ahn et al. (2008 PU model to a simplified model and collected 145 subjects’ IGT performance as the benchmark data for comparison. In our simplified PU model, the best goodness-of-fit was found mostly while α approaching zero. More specifically, we retested the key parameters α, λ , and A in the PU model. Notably, the power of influence of the parameters α, λ, and A has a hierarchical order in terms of manipulating the goodness-of-fit in the PU model. Additionally, we found that the parameters λ and A may be ineffective when the parameter α is close to zero in the PU model. The present simplified model demonstrated that decision makers mostly adopted the strategy of gain-stay-loss-shift rather than foreseeing the long-term outcome. However, there still have other behavioral variables that are not well revealed under these dynamic uncertainty situations. Therefore, the optimal behavioral models may not have been found. In short, the best model for predicting choice behavior under dynamic-uncertainty situations should be further evaluated.

  13. Comparison of simplified quantitative analyses of FDG uptake

    International Nuclear Information System (INIS)

    Graham, M.M.; Peterson, L.M.; Hayward, R.M.

    2000-01-01

    Quantitative analysis of [ 18 F]-fluoro-deoxyglucose (FDG) uptake is important in oncologic positron emission tomography (PET) studies to be able to set an objective threshold in determining if a tissue is malignant or benign, in assessing response to therapy, and in attempting to predict the aggressiveness of an individual tumor. The most common method used today for simple, clinical quantitation is standardized uptake value (SUV). SUV is normalized for body weight. Other potential normalization factors are lean body mass (LBM) or body surface area (BSA). More complex quantitation schemes include simplified kinetic analysis (SKA), Patlak graphical analysis (PGA), and parameter optimization of the complete kinetic model to determine FDG metabolic rate (FDGMR). These various methods were compared in a group of 40 patients with colon cancer metastatic to the liver. The methods were assessed by (1) correlation with FDGMR, (2) ability to predict survival using Kaplan-Meier plots, and (3) area under receiver operating characteristic (ROC) curves for distinguishing between tumor and normal liver. The best normalization scheme appears to be BSA with minor differences depending on the specific formula used to calculate BSA. Overall, PGA is the best predictor of outcome and best discriminator between normal tissue and tumor. SKA is almost as good. In conventional PET imaging it is worthwhile to normalize SUV using BSA. If a single blood sample is available, it is possible to use the SKA method, which is distinctly better. If more than one image is available, along with at least one blood sample, PGA is feasible and should produce the most accurate results

  14. Malware Normalization

    OpenAIRE

    Christodorescu, Mihai; Kinder, Johannes; Jha, Somesh; Katzenbeisser, Stefan; Veith, Helmut

    2005-01-01

    Malware is code designed for a malicious purpose, such as obtaining root privilege on a host. A malware detector identifies malware and thus prevents it from adversely affecting a host. In order to evade detection by malware detectors, malware writers use various obfuscation techniques to transform their malware. There is strong evidence that commercial malware detectors are susceptible to these evasion tactics. In this paper, we describe the design and implementation of a malware normalizer ...

  15. Broadening and Simplifying the First SETI Protocol

    Science.gov (United States)

    Michaud, M. A. G.

    The Declaration of Principles Concerning Activities Following the Detection of Extraterrestrial Intelligence, known informally as the First SETI Protocol, is the primary existing international guidance on this subject. During the fifteen years since the document was issued, several people have suggested revisions or additional protocols. This article proposes a broadened and simplified text that would apply to the detection of alien technology in our solar system as well as to electromagnetic signals from more remote sources.

  16. Rules of thumb and simplified methods

    International Nuclear Information System (INIS)

    Lahti, G.P.

    1985-01-01

    The author points out the value of a thorough grounding in fundamental physics combined with experience of applied practice when using simplified methods and rules of thumb in shield engineering. Present-day quality assurance procedures and good engineering practices require careful documentation of all calculations. The aforementioned knowledge of rules of thumb and back-of-the-envelope calculations can assure both the preparer and the reviewer that the results in the quality assurance documentation are the physically correct ones

  17. APPLICATION OF SIMPLIFIED TAXATION SYSTEM IN CONSTRUCTION

    Directory of Open Access Journals (Sweden)

    O. S. Golubova

    2011-01-01

    Full Text Available Specificity concerning cost formation of construction work executed by  entities of small business enterprises that use a simplified taxation system has a direct impact on the effectiveness of organization activity. Dozens of business entities applying various taxation systems are involved in the execution of the construction process. For this reason an inclusion of taxes in work cost may have a decisive influence on the selection of a contractor for an object construction.  

  18. Cloud computing can simplify HIT infrastructure management.

    Science.gov (United States)

    Glaser, John

    2011-08-01

    Software as a Service (SaaS), built on cloud computing technology, is emerging as the forerunner in IT infrastructure because it helps healthcare providers reduce capital investments. Cloud computing leads to predictable, monthly, fixed operating expenses for hospital IT staff. Outsourced cloud computing facilities are state-of-the-art data centers boasting some of the most sophisticated networking equipment on the market. The SaaS model helps hospitals safeguard against technology obsolescence, minimizes maintenance requirements, and simplifies management.

  19. Development of simplified rotating plug seal structure

    International Nuclear Information System (INIS)

    Ueta, M.; Ichimiya, M.; Kanaoka, T.; Sekiya, H.; Ueda, S.; Ishibashi, S.

    1991-01-01

    We studied a compact and simplified rotating plug seal structure and conducted experiments for key elements of the concept such us the mechanical seal structure and sodium deposit prevention system. Good characteristics were confirmed for the mechanical seal structure, which utilizes an elastomer seal and thin lathe bearing. Applicability of the density barrier concept was also confirmed as the sodium deposit prevention system. This concept can be applied to actual plants. (author)

  20. Current limiters

    Energy Technology Data Exchange (ETDEWEB)

    Loescher, D.H. [Sandia National Labs., Albuquerque, NM (United States). Systems Surety Assessment Dept.; Noren, K. [Univ. of Idaho, Moscow, ID (United States). Dept. of Electrical Engineering

    1996-09-01

    The current that flows between the electrical test equipment and the nuclear explosive must be limited to safe levels during electrical tests conducted on nuclear explosives at the DOE Pantex facility. The safest way to limit the current is to use batteries that can provide only acceptably low current into a short circuit; unfortunately this is not always possible. When it is not possible, current limiters, along with other design features, are used to limit the current. Three types of current limiters, the fuse blower, the resistor limiter, and the MOSFET-pass-transistor limiters, are used extensively in Pantex test equipment. Detailed failure mode and effects analyses were conducted on these limiters. Two other types of limiters were also analyzed. It was found that there is no best type of limiter that should be used in all applications. The fuse blower has advantages when many circuits must be monitored, a low insertion voltage drop is important, and size and weight must be kept low. However, this limiter has many failure modes that can lead to the loss of over current protection. The resistor limiter is simple and inexpensive, but is normally usable only on circuits for which the nominal current is less than a few tens of milliamperes. The MOSFET limiter can be used on high current circuits, but it has a number of single point failure modes that can lead to a loss of protective action. Because bad component placement or poor wire routing can defeat any limiter, placement and routing must be designed carefully and documented thoroughly.

  1. Control of activation levels to simplify waste management of fusion reactor ferritic steel components

    International Nuclear Information System (INIS)

    Wiffen, F.W.; Santoro, R.T.

    1984-01-01

    The objective of this work is to examine the restrictions placed on the composition of steels to allow simplified waste management after service in a fusion reactor first wall. Decay of steel activity within tens of years could simplify waste disposal or even permit recycle. For material recycle, N, Al, Ni, Cu, Nb, and Mo must be excluded. For shallow land burial, initial concentration limits include (in at. ppM) Ni, <20,000; Mo, <3650; N, <3650; Cu, <2400; and Nb, <1.0. Other constituents of steels will not be limited

  2. Predicting outcome in term neonates with hypoxic-ischaemic encephalopathy using simplified MR criteria

    International Nuclear Information System (INIS)

    Jyoti, Rajeev; O'Neil, Ross

    2006-01-01

    MRI is an established investigation in the evaluation of neonates with suspected hypoxic-ischaemic encephalopathy (HIE). However, its role as a predictor of neurodevelopmental outcome remains complex. To establish reproducible simplified MR criteria and evaluate their role in predicting neurodevelopmental outcome in term neonates with HIE. Term neonates with suspected HIE had MRI at 7-10 days of age. MR scans were interpreted according to new simplified criteria by two radiologists blinded to the clinical course and outcome. The new simplified criteria allocated grade 1 to cases with no central and less than 10% peripheral change, grade 2 to those with less than 30% central and/or 10-30% peripheral area change, and grade 3 to those with more than 30% central or peripheral change. MRI changes were compared with clinical neurodevelopmental outcome evaluated prospectively at 1 year of age. Neurodevelopmental outcome was based upon the DQ score (revised Griffith's) and cerebral palsy on neurological assessment. Of 20 subjects, all those showing severe (grade 3) MR changes (35%) died or had poor neurodevelopmental outcome. Subjects with a normal MR scan or with scans showing only mild (grade 1) MR changes (55%) had normal outcomes. One subject showing moderate (grade 2) changes on MRI had a moderate outcome (5%), while another had an atypical pattern of MR changes with a normal outcome (5%). Assessment of full-term neonates with suspected HIE using the simplified MR criteria is highly predictive of neurodevelopmental outcome. (orig.)

  3. Predicting outcome in term neonates with hypoxic-ischaemic encephalopathy using simplified MR criteria

    Energy Technology Data Exchange (ETDEWEB)

    Jyoti, Rajeev; O' Neil, Ross [Canberra Hospital, Medical Imaging, Canberra, ACT (Australia)

    2006-01-01

    MRI is an established investigation in the evaluation of neonates with suspected hypoxic-ischaemic encephalopathy (HIE). However, its role as a predictor of neurodevelopmental outcome remains complex. To establish reproducible simplified MR criteria and evaluate their role in predicting neurodevelopmental outcome in term neonates with HIE. Term neonates with suspected HIE had MRI at 7-10 days of age. MR scans were interpreted according to new simplified criteria by two radiologists blinded to the clinical course and outcome. The new simplified criteria allocated grade 1 to cases with no central and less than 10% peripheral change, grade 2 to those with less than 30% central and/or 10-30% peripheral area change, and grade 3 to those with more than 30% central or peripheral change. MRI changes were compared with clinical neurodevelopmental outcome evaluated prospectively at 1 year of age. Neurodevelopmental outcome was based upon the DQ score (revised Griffith's) and cerebral palsy on neurological assessment. Of 20 subjects, all those showing severe (grade 3) MR changes (35%) died or had poor neurodevelopmental outcome. Subjects with a normal MR scan or with scans showing only mild (grade 1) MR changes (55%) had normal outcomes. One subject showing moderate (grade 2) changes on MRI had a moderate outcome (5%), while another had an atypical pattern of MR changes with a normal outcome (5%). Assessment of full-term neonates with suspected HIE using the simplified MR criteria is highly predictive of neurodevelopmental outcome. (orig.)

  4. A simplified physics-based model for nickel hydrogen battery

    Science.gov (United States)

    Liu, Shengyi; Dougal, Roger A.; Weidner, John W.; Gao, Lijun

    This paper presents a simplified model of a nickel hydrogen battery based on a first approximation. The battery is assumed uniform throughout. The reversible potential is considered primarily due to one-electron transfer redox reaction of nickel hydroxide and nickel oxyhydroxide. The non-ideality due to phase reactions is characterized by the two-parameter activity coefficients. The overcharge process is characterized by the oxygen reaction. The overpotentials are lumped to a tunable resistive drop to fit particular battery designs. The model is implemented in the Virtual Test Bed environment, and the characteristics of the battery are simulated and in good agreement with the experimental data within the normal operating regime. The model can be used for battery dynamic simulation and design in a satellite power system, an example of which is given.

  5. Normal accidents

    International Nuclear Information System (INIS)

    Perrow, C.

    1989-01-01

    The author has chosen numerous concrete examples to illustrate the hazardousness inherent in high-risk technologies. Starting with the TMI reactor accident in 1979, he shows that it is not only the nuclear energy sector that bears the risk of 'normal accidents', but also quite a number of other technologies and industrial sectors, or research fields. The author refers to the petrochemical industry, shipping, air traffic, large dams, mining activities, and genetic engineering, showing that due to the complexity of the systems and their manifold, rapidly interacting processes, accidents happen that cannot be thoroughly calculated, and hence are unavoidable. (orig./HP) [de

  6. Simplified methods to assess thermal fatigue due to turbulent mixing

    International Nuclear Information System (INIS)

    Hannink, M.H.C.; Timperi, A.

    2011-01-01

    Thermal fatigue is a safety relevant damage mechanism in pipework of nuclear power plants. A well-known simplified method for the assessment of thermal fatigue due to turbulent mixing is the so-called sinusoidal method. Temperature fluctuations in the fluid are described by a sinusoidally varying signal at the inner wall of the pipe. Because of limited information on the thermal loading conditions, this approach generally leads to overconservative results. In this paper, a new assessment method is presented, which has the potential of reducing the overconservatism of existing procedures. Artificial fluid temperature signals are generated by superposition of harmonic components with different amplitudes and frequencies. The amplitude-frequency spectrum of the components is modelled by a formula obtained from turbulence theory, whereas the phase differences are assumed to be randomly distributed. Lifetime predictions generated with the new simplified method are compared with lifetime predictions based on real fluid temperature signals, measured in an experimental setup of a mixing tee. Also, preliminary steady-state Computational Fluid Dynamics (CFD) calculations of the total power of the fluctuations are presented. The total power is needed as an input parameter for the spectrum formula in a real-life application. Solution of the transport equation for the total power was included in a CFD code and comparisons with experiments were made. The newly developed simplified method for generating the temperature signal is shown to be adequate for the investigated geometry and flow conditions, and demonstrates possibilities of reducing the conservatism of the sinusoidal method. CFD calculations of the total power show promising results, but further work is needed to develop the approach. (author)

  7. Reconstructing Normality

    DEFF Research Database (Denmark)

    Gildberg, Frederik Alkier; Bradley, Stephen K.; Fristed, Peter Billeskov

    2012-01-01

    Forensic psychiatry is an area of priority for the Danish Government. As the field expands, this calls for increased knowledge about mental health nursing practice, as this is part of the forensic psychiatry treatment offered. However, only sparse research exists in this area. The aim of this study...... was to investigate the characteristics of forensic mental health nursing staff interaction with forensic mental health inpatients and to explore how staff give meaning to these interactions. The project included 32 forensic mental health staff members, with over 307 hours of participant observations, 48 informal....... The intention is to establish a trusting relationship to form behaviour and perceptual-corrective care, which is characterized by staff's endeavours to change, halt, or support the patient's behaviour or perception in relation to staff's perception of normality. The intention is to support and teach the patient...

  8. Pursuing Normality

    DEFF Research Database (Denmark)

    Madsen, Louise Sofia; Handberg, Charlotte

    2018-01-01

    implying an influence on whether to participate in cancer survivorship care programs. Because of "pursuing normality," 8 of 9 participants opted out of cancer survivorship care programming due to prospects of "being cured" and perceptions of cancer survivorship care as "a continuation of the disease......BACKGROUND: The present study explored the reflections on cancer survivorship care of lymphoma survivors in active treatment. Lymphoma survivors have survivorship care needs, yet their participation in cancer survivorship care programs is still reported as low. OBJECTIVE: The aim of this study...... was to understand the reflections on cancer survivorship care of lymphoma survivors to aid the future planning of cancer survivorship care and overcome barriers to participation. METHODS: Data were generated in a hematological ward during 4 months of ethnographic fieldwork, including participant observation and 46...

  9. Digital arteriography of kidney arteries by intraveinous route. Simplified technique

    International Nuclear Information System (INIS)

    Guisgand, M.; Dardenne, A.N.

    1989-01-01

    Of the 1,000 patients addressed to us for intravenous digital angiography (IVDA) of the renal arteries for arterial hypertension, for control of the artery of a transplanted kidney or for preoperative check-up prior to transplantation of a kidney, 738 were examined by a simplified technique. Compared to the standard practice this method simply consists of a manual injection of a standard ionic contrast medium via an antecubital vein punctured with a large catheter needle (caliber 14 G), without preparatory injection of an intestinal antispasmodic. This method has produced a satisfactory arterial opacification in 96 % of the cases. The advantages and disadvantages of the technique are discussed. Of the 262 remaining patients, 250 were also examined by the peripheral venous mode, but the technique had to be modified in at least one of its aspects for one reason or another. Only 12 patients were not examined by the peripheral venous mode (7 puncture failures, 4 permanent venous accesses already installed). The IVDA simplified technique appears to be reliable for detecting reno-vascular arterial hyper-tension and, with certain limitations, for the control of kidney grafts. With regard to the preoperative check-up before kidney transplantation, IVDA still does not seem a suitable replacement for the traditional method of angiography [fr

  10. Use of simplified methods for predicting natural resource damages

    International Nuclear Information System (INIS)

    Loreti, C.P.; Boehm, P.D.; Gundlach, E.R.; Healy, E.A.; Rosenstein, A.B.; Tsomides, H.J.; Turton, D.J.; Webber, H.M.

    1995-01-01

    To reduce transaction costs and save time, the US Department of the Interior (DOI) and the National Oceanic and Atmospheric Administration (NOAA) have developed simplified methods for assessing natural resource damages from oil and chemical spills. DOI has proposed the use of two computer models, the Natural Resource Damage Assessment Model for Great Lakes Environments (NRDAM/GLE) and a revised Natural Resource Damage Assessment Model for Coastal and Marine Environments (NRDAM/CME) for predicting monetary damages for spills of oils and chemicals into the Great Lakes and coastal and marine environments. NOAA has used versions of these models to create Compensation Formulas, which it has proposed for calculating natural resource damages for oil spills of up to 50,000 gallons anywhere in the US. Based on a review of the documentation supporting the methods, the results of hundreds of sample runs of DOI's models, and the outputs of the thousands of model runs used to create NOAA's Compensation Formulas, this presentation discusses the ability of these simplified assessment procedures to make realistic damage estimates. The limitations of these procedures are described, and the need for validating the assumptions used in predicting natural resource injuries is discussed

  11. Washington's marine oil spill compensation schedule - simplified resource damage assessment

    International Nuclear Information System (INIS)

    Geselbracht, L.; Logan, R.

    1993-01-01

    The Washington State Preassessment Screening and Oil Spill Compensation Schedule Rule (Chapter 173-183 Washington Administrative Code), which simplifies natural resource damage assessment for many oil spill cases, became effective in May 1992. The approach described in the rule incorporates a number of preconstructed rankings that rate environmental sensitivity and the propensity of spilled oil to cause environmental harm. The rule also provides guidance regarding how damages calculated under the schedule should be reduced to take into account actions taken by the responsible party that reduce environmental injury. To apply the compensation schedule to marine estuarine spills, the resource trustees need only collect a limited amount of information such as type of product spilled, number of gallons spilled, compensation schedule subregions the spill entered, season of greatest spill impact, percent coverage of habitats affected by the spill, and actions taken by the responsible party. The result of adding a simplified tool to the existing assortment of damage assessment approaches is that resource trustees will now be able to assess damages for most oil spill cases and shift more effort than was possible in the past to resource restoration

  12. Quantitative whole body scintigraphy - a simplified approach

    International Nuclear Information System (INIS)

    Marienhagen, J.; Maenner, P.; Bock, E.; Schoenberger, J.; Eilles, C.

    1996-01-01

    In this paper we present investigations on a simplified method of quantitative whole body scintigraphy by using a dual head LFOV-gamma camera and a calibration algorithm without the need of additional attenuation or scatter correction. Validation of this approach to the anthropomorphic phantom as well as in patient studies showed a high accuracy concerning quantification of whole body activity (102.8% and 97.72%, resp.), by contrast organ activities were recovered with an error range up to 12%. The described method can be easily performed using commercially available software packages and is recommendable especially for quantitative whole body scintigraphy in a clinical setting. (orig.) [de

  13. Simplified stock markets described by number operators

    Science.gov (United States)

    Bagarello, F.

    2009-06-01

    In this paper we continue our systematic analysis of the operatorial approach previously proposed in an economical context and we discuss a mixed toy model of a simplified stock market, i.e. a model in which the price of the shares is given as an input. We deduce the time evolution of the portfolio of the various traders of the market, as well as of other observable quantities. As in a previous paper, we solve the equations of motion by means of a fixed point like approximation.

  14. Simplified dynamic buckling assessment of steel containments

    International Nuclear Information System (INIS)

    Farrar, C.R.; Duffey, T.A.; Renick, D.H.

    1993-01-01

    A simplified, three-degree-of-freedom analytical procedure for performing a response spectrum buckling analysis of a thin containment shell is developed. Two numerical examples with R/t values which bound many existing steel containments are used to illustrate the procedure. The role of damping on incipient buckling acceleration level is evaluated for a regulatory seismic spectrum using the two numerical examples. The zero-period acceleration level that causes incipient buckling in either of the two containments increases 31% when damping is increased from 1% to 4% of critical. Comparisons with finite element results on incipient buckling levels are favorable

  15. Chronic Meningitis: Simplifying a Diagnostic Challenge.

    Science.gov (United States)

    Baldwin, Kelly; Whiting, Chris

    2016-03-01

    Chronic meningitis can be a diagnostic dilemma for even the most experienced clinician. Many times, the differential diagnosis is broad and encompasses autoimmune, neoplastic, and infectious etiologies. This review will focus on a general approach to chronic meningitis to simplify the diagnostic challenges many clinicians face. The article will also review the most common etiologies of chronic meningitis in some detail including clinical presentation, diagnostic testing, treatment, and outcomes. By using a case-based approach, we will focus on the key elements of clinical presentation and laboratory analysis that will yield the most rapid and accurate diagnosis in these complicated cases.

  16. Appraisal of allowable loads by simplified rules

    International Nuclear Information System (INIS)

    Moulin, D.; Roche, R.L.

    1984-06-01

    This paper presents a simplified method of analysis of buckling of thin structures like those of L.M.F.B.R.'s. The edification of the method is very similar to methods used for buckling of beams and columns having initial geometric imperfections and buckling in the plastic range. Particular attention is paid to the stress hardening of material involved (austenitic steel) and to possible unstable post buckling of thin structures. The analysis method is based on elastic calculation and diagrams that take into account various initial geometric defects

  17. Simplified analysis for liquid pathway studies

    International Nuclear Information System (INIS)

    Codell, R.B.

    1984-08-01

    The analysis of the potential contamination of surface water via groundwater contamination from severe nuclear accidents is routinely calculated during licensing reviews. This analysis is facilitated by the methods described in this report, which is codified into a BASIC language computer program, SCREENLP. This program performs simplified calculations for groundwater and surface water transport and calculates population doses to potential users for the contaminated water irrespective of possible mitigation methods. The results are then compared to similar analyses performed using data for the generic sites in NUREG-0440, Liquid Pathway Generic Study, to determine if the site being investigated would pose any unusual liquid pathway hazards

  18. Simplified scheme or radioactive plume calculations

    International Nuclear Information System (INIS)

    Gibson, T.A.; Montan, D.N.

    1976-01-01

    A simplified mathematical scheme to estimate external whole-body γ radiation exposure rates from gaseous radioactive plumes was developed for the Rio Blanco Gas Field Nuclear Stimulation Experiment. The method enables one to calculate swiftly, in the field, downwind exposure rates knowing the meteorological conditions and γ radiation exposure rates measured by detectors positioned near the plume source. The method is straightforward and easy to use under field conditions without the help of mini-computers. It is applicable to a wide range of radioactive plume situations. It should be noted that the Rio Blanco experiment was detonated on May 17, 1973, and no seep or release of radioactive material occurred

  19. Simplified methodology for Angra 1 containment analysis

    International Nuclear Information System (INIS)

    Neves Conti, T. das; Souza, A.L. de; Sabundjian, G.

    1991-08-01

    A simplified methodology of analysis was developed to simulate a Large Break Loss of Coolant Accident in the Angra 1 Nuclear Power Station. Using the RELAP5/MOD1, RELAP4/MOD5 and CONTEMPT-LT Codes, the time variation of pressure and temperature in the containment was analysed. The obtained data was compared with the Angra 1 Final Safety Analysis Report, and too those calculated by a Detailed Model. The results obtained by this new methodology such as the small computational time of simulation, were satisfactory when getting the preliminary evaluation of the Angra 1 global parameters. (author)

  20. Atmospheric dispersion and the radiological consequences of normal airborne effluents from a nuclear power plant

    International Nuclear Information System (INIS)

    Fang, D.; Yang, L.; Sun, C.Z.

    1995-01-01

    The relationship between the consequences of the normal exhaust of radioactive materials in air from nuclear power plants and atmospheric dispersion is studied. Because the source terms of the exhaust from a nuclear power plant are relatively low and their radiological consequences are far less than the corresponding authoritative limits, the atmospheric dispersion models, their various modifications, and selections of relevant parameters have few effects on those consequences. In the environmental assessment and siting, the emphasis should not be placed on the consequence evaluation of routine exhaust of nuclear power plants, and the calculation of consequences of the exhaust and atmospheric field measurements should be appropriately, simplified. 12 refs., 5 figs., 7 tabs

  1. SBWR: A simplified boiling water reactor

    International Nuclear Information System (INIS)

    Duncan, J.D.; Sawyer, C.D.; Lagache, M.P.

    1987-01-01

    An advanced light water reactor concept is being developed for possible application in the 1990's. The concept, known as SBWR is a boiling water reactor which uses natural circulation to provide flow to the reactor core. In an emergency, a gravity driven core cooling system is used. The reactor is depressurized and water from an elevated suppression pool flows by gravity to the reactor vessel to keep the reactor core covered. The concept also features a passive containment cooling system in which water flows by gravity to cool the suppression pool wall. No operator action is required for a period of at least three days. Use of these and other passive systems allows the elimination of emergency diesel generators, core cooling pumps and heat removal pumps which is expected to simplify the plant design, reduce costs and simplify licensing. The concept is being developed by General Electric, Bechtel and the Massachusetts Institute of Technology supported by the Electric Power Research Institute and the United States Department of Energy in the United States. In Japan, The Japan Atomic Power Company has a great interest in this concept

  2. Simplified Transit Procedure in Railway Transport

    Directory of Open Access Journals (Sweden)

    Željko Kokorović

    2008-11-01

    Full Text Available The current transit procedure in railway transport that iscarried out on the basis of the Customs Act [ 11 of the Republicof Croatia is applied only up to the border, i. e. the issued documentsand guarantees are valid only up to the border, and byjoining the Convention on Common transit procedure, i. e. integrationof the Republic of Croatia in the European Union, theRepublic of Croatia will also have to implement the regulationsand rules of Simplified transit procedure valid in each of thethirty member states. In international railway traffic, the transportof goods is regulated by the Convention concerning InternationalCarriage by Rail- COT IF [2 1 and usage of the CIMwaybill (Contract for International Carriage of Goods by Rail.If the goods are transported in Simplified transit procedure, theformalities regarding the transport of goods performed by railcarriers using the international waybill CIM will be significantlysimplified and accelerated. In principle there are no delays dueto customs on the borders when crossing the EU borders andborders of the Convention member states, contributing greatlyto the acceleration of the transport of goods, reduction of waitingcosts and paperwork, as well as influence on the schedulereliability.

  3. A simplified multisupport response spectrum method

    Science.gov (United States)

    Ye, Jihong; Zhang, Zhiqiang; Liu, Xianming

    2012-03-01

    A simplified multisupport response spectrum method is presented. The structural response is a sum of two components of a structure with a first natural period less than 2 s. The first component is the pseudostatic response caused by the inconsistent motions of the structural supports, and the second is the structural dynamic response to ground motion accelerations. This method is formally consistent with the classical response spectrum method, and the effects of multisupport excitation are considered for any modal response spectrum or modal superposition. If the seismic inputs at each support are the same, the support displacements caused by the pseudostatic response become rigid body displacements. The response spectrum in the case of multisupport excitations then reduces to that for uniform excitations. In other words, this multisupport response spectrum method is a modification and extension of the existing response spectrum method under uniform excitation. Moreover, most of the coherency coefficients in this formulation are simplified by approximating the ground motion excitation as white noise. The results indicate that this simplification can reduce the calculation time while maintaining accuracy. Furthermore, the internal forces obtained by the multisupport response spectrum method are compared with those produced by the traditional response spectrum method in two case studies of existing long-span structures. Because the effects of inconsistent support displacements are not considered in the traditional response spectrum method, the values of internal forces near the supports are underestimated. These regions are important potential failure points and deserve special attention in the seismic design of reticulated structures.

  4. Simplifying informed consent for biorepositories: stakeholder perspectives.

    Science.gov (United States)

    Beskow, Laura M; Friedman, Joëlle Y; Hardy, N Chantelle; Lin, Li; Weinfurt, Kevin P

    2010-09-01

    Complex and sometimes controversial information must be conveyed during the consent process for participation in biorepositories, and studies suggest that consent documents in general are growing in length and complexity. As a first step toward creating a simplified biorepository consent form, we gathered data from multiple stakeholders about what information was most important for prospective participants to know when making a decision about taking part in a biorepository. We recruited 52 research participants, 12 researchers, and 20 institutional review board representatives from Durham and Kannapolis, NC. These subjects were asked to read a model biorepository consent form and highlight sentences they deemed most important. On average, institutional review board representatives identified 72.3% of the sentences as important; researchers selected 53.0%, and participants 40.4% (P = 0.0004). Participants most often selected sentences about the kinds of individual research results that might be offered, privacy risks, and large-scale data sharing. Researchers highlighted sentences about the biorepository's purpose, privacy protections, costs, and participant access to individual results. Institutional review board representatives highlighted sentences about collection of basic personal information, medical record access, and duration of storage. The differing mandates of these three groups can translate into widely divergent opinions about what information is important and appropriate to include a consent form. These differences could frustrate efforts to move simplified forms--for biobanking as well as for other kinds of research--into actual use, despite continued calls for such forms.

  5. Applicability Evaluation of Simplified Cognitive Behavioral Therapy.

    Science.gov (United States)

    Zhang, Li; Zhu, Zhipei; Fang, Fang; Shen, Yuan; Liu, Na; Li, Chunbo

    2018-04-25

    We have developed a structured cognitive behavioral therapy manual for anxiety disorder in China, and the present study evaluated the applicability of simplified cognitive behavioral therapy based on our previous research. To evaluate the applicability of simplified cognitive behavioral therapy (SCBT) on generalized anxiety disorder (GAD) by conducting a multi-center controlled clinical trial. A multi-center controlled clinical trial of SCBT was conducted on patients with GAD, including institutions specializing in mental health and psychiatry units in general hospitals. The participants were divided into 3 groups: SCBT group, SCBT with medication group and medication group. The drop-out rates of these three groups, the therapy satisfaction of patients who received SCBT and the evaluation of SCBT from therapists were compared. (1) There was no significant difference among the drop-out rates in the three groups. (2) Only the duration and times of therapy were significantly different between the two groups of patients who received the SCBT, and the therapy satisfaction of the SCBT group was higher than that of the SCBT with medication group. (3) Eighteen therapists who conducted the SCBT indicated that the manual was easy to comprehend and operate, and this therapy could achieve the therapy goals. The applicability of SCBT for patients with GAD is relatively high, and it is hopeful that SCBT can become a psychological treatment which can be applied in medical institutions of various levels.

  6. Simplified phenomenology for colored dark sectors

    Energy Technology Data Exchange (ETDEWEB)

    Hedri, Sonia El; Kaminska, Anna; Vries, Maikel de [PRISMA Cluster of Excellence & Mainz Institute for Theoretical Physics,Johannes Gutenberg University,55099 Mainz (Germany); Zurita, Jose [Institute for Nuclear Physics (IKP), Karlsruhe Institute of Technology,Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Institute for Theoretical Particle Physics (TTP), Karlsruhe Institute of Technology,Engesserstraße 7, D-76128 Karlsruhe (Germany)

    2017-04-20

    We perform a general study of the relic density and LHC constraints on simplified models where the dark matter coannihilates with a strongly interacting particle X. In these models, the dark matter depletion is driven by the self-annihilation of X to pairs of quarks and gluons through the strong interaction. The phenomenology of these scenarios therefore only depends on the dark matter mass and the mass splitting between dark matter and X as well as the quantum numbers of X. In this paper, we consider simplified models where X can be either a scalar, a fermion or a vector, as well as a color triplet, sextet or octet. We compute the dark matter relic density constraints taking into account Sommerfeld corrections and bound state formation. Furthermore, we examine the restrictions from thermal equilibrium, the lifetime of X and the current and future LHC bounds on X pair production. All constraints are comprehensively presented in the mass splitting versus dark matter mass plane. While the relic density constraints can lead to upper bounds on the dark matter mass ranging from 2 TeV to more than 10 TeV across our models, the prospective LHC bounds range from 800 to 1500 GeV. A full coverage of the strongly coannihilating dark matter parameter space would therefore require hadron colliders with significantly higher center-of-mass energies.

  7. Simplified pancreatoduodenectomy for complex blunt pancreaticoduodenal injury

    Directory of Open Access Journals (Sweden)

    FENG Xin-fu

    2013-10-01

    Full Text Available 【Abstract】A 34-year-old man admitted to our department with complex blunt pancreaticoduodenal injury after a car accident. The wall of the first, second, and third portions of the duodenum was extensively lacerated, and the pancreas was longitudinally transected along the superior mesenteric vein-portal vein trunk. The pancreatic head and the uncinate process were devitalized and the distal common bile duct and the proximal main pancreatic duct were completely detached from the Vater ampulla. The length of the stump of distal common bile located at the cut surface of remnant pancreas was approximately 0.6 cm. A simplified Kausch-Whipple’s procedure was performed after debridement of the devitalized pancreatic head and resection of the damaged duodenum in which the stump of distal common bile duct and the pancreatic remnant were embedded into the jejunal loop. Postoperative wound abscess appeared that eventually recovered by conservative treatment. During 16 months follow-up the patient has been stable and healthy. A simplified pancreaticoduodenectomy is a safe alternative for the Whipple procedure in managing complex pancreaticoduodenal injury in a hemodynamically stable patient. Key words: Pancreaticoduodenectomy; Abdominal injuries; Pancreas; Duodenum

  8. Less-simplified models of dark matter for direct detection and the LHC

    Energy Technology Data Exchange (ETDEWEB)

    Choudhury, Arghya [Regional Centre for Accelerator-based Particle Physics, Harish-Chandra Research Institute,Allahabad - 211019 (India); Kowalska, Kamila; Roszkowski, Leszek; Sessolo, Enrico Maria; Williams, Andrew J. [National Centre for Nuclear Research,Hoża 69, 00-681 Warsaw (Poland)

    2016-04-29

    We construct models of dark matter with suppressed spin-independent scattering cross section utilizing the existing simplified model framework. Even simple combinations of simplified models can exhibit interference effects that cause the tree level contribution to the scattering cross section to vanish, thus demonstrating that direct detection limits on simplified models are not robust when embedded in a more complicated and realistic framework. In general for fermionic WIMP masses ≳10 GeV direct detection limits on the spin-independent scattering cross section are much stronger than those coming from the LHC. However these model combinations, which we call less-simplified models, represent situations where LHC searches become more competitive than direct detection experiments even for moderate dark matter mass. We show that a complementary use of several searches at the LHC can strongly constrain the direct detection blind spots by setting limits on the coupling constants and mediators’ mass. We derive the strongest limits for combinations of vector + scalar, vector + “squark”, and “squark” + scalar mediator, and present the corresponding projections for the LHC 14 TeV for a number of searches: mono-jet, jets + missing energy, and searches for heavy vector resonances.

  9. The Effect of a Simplified English Language Dictionary on a Reading Test. LEP Projects Report 1.

    Science.gov (United States)

    Albus, Deb; Bielinski, John; Thurlow, Martha; Liu, Kristin

    This study was conducted to examine whether using a monolingual, simplified English dictionary as an accommodation on a reading test with limited-English-proficient (LEP) Hmong students improved test performance. Hmong students were chosen because they are often not literate in their first language. For these students, bilingual dictionaries are…

  10. Less-simplified models of dark matter for direct detection and the LHC

    International Nuclear Information System (INIS)

    Choudhury, Arghya; Kowalska, Kamila; Roszkowski, Leszek; Sessolo, Enrico Maria; Williams, Andrew J.

    2016-01-01

    We construct models of dark matter with suppressed spin-independent scattering cross section utilizing the existing simplified model framework. Even simple combinations of simplified models can exhibit interference effects that cause the tree level contribution to the scattering cross section to vanish, thus demonstrating that direct detection limits on simplified models are not robust when embedded in a more complicated and realistic framework. In general for fermionic WIMP masses ≳10 GeV direct detection limits on the spin-independent scattering cross section are much stronger than those coming from the LHC. However these model combinations, which we call less-simplified models, represent situations where LHC searches become more competitive than direct detection experiments even for moderate dark matter mass. We show that a complementary use of several searches at the LHC can strongly constrain the direct detection blind spots by setting limits on the coupling constants and mediators’ mass. We derive the strongest limits for combinations of vector + scalar, vector + “squark”, and “squark” + scalar mediator, and present the corresponding projections for the LHC 14 TeV for a number of searches: mono-jet, jets + missing energy, and searches for heavy vector resonances.

  11. Less-simplified models of dark matter for direct detection and the LHC

    Science.gov (United States)

    Choudhury, Arghya; Kowalska, Kamila; Roszkowski, Leszek; Sessolo, Enrico Maria; Williams, Andrew J.

    2016-04-01

    We construct models of dark matter with suppressed spin-independent scattering cross section utilizing the existing simplified model framework. Even simple combinations of simplified models can exhibit interference effects that cause the tree level contribution to the scattering cross section to vanish, thus demonstrating that direct detection limits on simplified models are not robust when embedded in a more complicated and realistic framework. In general for fermionic WIMP masses ≳ 10 GeV direct detection limits on the spin-independent scattering cross section are much stronger than those coming from the LHC. However these model combinations, which we call less-simplified models, represent situations where LHC searches become more competitive than direct detection experiments even for moderate dark matter mass. We show that a complementary use of several searches at the LHC can strongly constrain the direct detection blind spots by setting limits on the coupling constants and mediators' mass. We derive the strongest limits for combinations of vector + scalar, vector + "squark", and "squark" + scalar mediator, and present the corresponding projections for the LHC 14 TeV for a number of searches: mono-jet, jets + missing energy, and searches for heavy vector resonances.

  12. Fundamental characteristics and simplified evaluation method of dynamic earth pressure

    International Nuclear Information System (INIS)

    Nukui, Y.; Inagaki, Y.; Ohmiya, Y.

    1989-01-01

    In Japan, a method is commonly used in the evaluation of dynamic earth pressure acting on the underground walls of a deeply embedded nuclear reactor building. However, since this method was developed on the basis of the limit state of soil supported by retaining walls, the behavior of dynamic earth pressure acting on the embedded part of a nuclear reactor building may differ from the estimated by this method. This paper examines the fundamental characteristics of dynamic earth pressure through dynamic soil-structure interaction analysis. A simplified method to evaluate dynamic earth pressure for the design of underground walls of a nuclear reactor building is described. The dynamic earth pressure is fluctuating earth pressure during earthquake

  13. Simplified theory of plastic zones based on Zarka's method

    CERN Document Server

    Hübel, Hartwig

    2017-01-01

    The present book provides a new method to estimate elastic-plastic strains via a series of linear elastic analyses. For a life prediction of structures subjected to variable loads, frequently encountered in mechanical and civil engineering, the cyclically accumulated deformation and the elastic plastic strain ranges are required. The Simplified Theory of Plastic Zones (STPZ) is a direct method which provides the estimates of these and all other mechanical quantities in the state of elastic and plastic shakedown. The STPZ is described in detail, with emphasis on the fact that not only scientists but engineers working in applied fields and advanced students are able to get an idea of the possibilities and limitations of the STPZ. Numerous illustrations and examples are provided to support the reader's understanding.

  14. Using simplified Chaos Theory to manage nursing services.

    Science.gov (United States)

    Haigh, Carol A

    2008-04-01

    The purpose of this study was to evaluate the part simplified chaos theory could play in the management of nursing services. As nursing care becomes more complex, practitioners need to become familiar with business planning and objective time management. There are many time-limited methods that facilitate this type of planning but few that can help practitioners to forecast the end-point outcome of the service they deliver. A growth model was applied to a specialist service to plot service trajectory. Components of chaos theory can play a role in forecasting service outcomes and consequently the impact upon the management of such services. The ability to (1) track the trajectory of a service and (2) manipulate that trajectory by introducing new variables can allow managers to forward plan for service development and to evaluate the effectiveness of a service by plotting its end-point state.

  15. A simplified tether model for molecular motor transporting cargo

    International Nuclear Information System (INIS)

    Fang-Zhen, Li; Li-Chun, Jiang

    2010-01-01

    Molecular motors are proteins or protein complexes which function as transporting engines in biological cells. This paper models the tether between motor and its cargo as a symmetric linear potential. Different from Elston and Peskin's work for which performance of the system was discussed only in some limiting cases, this study produces analytic solutions of the problem for general cases by simplifying the transport system into two physical states, which makes it possible to discuss the dynamics of the motor–cargo system in detail. It turns out that the tether strength between motor and cargo should be greater than a threshold or the motor will fail to transport the cargo, which was not discussed by former researchers yet. Value of the threshold depends on the diffusion coefficients of cargo and motor and also on the strength of the Brownian ratchets dragging the system. The threshold approaches a finite constant when the strength of the ratchet tends to infinity. (general)

  16. Simplified likelihood for the re-interpretation of public CMS results

    CERN Document Server

    The CMS Collaboration

    2017-01-01

    In this note, a procedure for the construction of simplified likelihoods for the re-interpretation of the results of CMS searches for new physics is presented. The procedure relies on the use of a reduced set of information on the background models used in these searches which can readily be provided by the CMS collaboration. A toy example is used to demonstrate the procedure and its accuracy in reproducing the full likelihood for setting limits in models for physics beyond the standard model. Finally, two representative searches from the CMS collaboration are used to demonstrate the validity of the simplified likelihood approach under realistic conditions.

  17. A Simplified Stabilizer ZX-calculus

    Directory of Open Access Journals (Sweden)

    Miriam Backens

    2017-01-01

    Full Text Available The stabilizer ZX-calculus is a rigorous graphical language for reasoning about quantum mechanics.The language is sound and complete: a stabilizer ZX-diagram can be transformed into another one if and only if these two diagrams represent the same quantum evolution or quantum state. We show that the stabilizer ZX-calculus can be simplified, removing unnecessary equations while keeping only the essential axioms which potentially capture fundamental structures of quantum mechanics. We thus give a significantly smaller set of axioms and prove that meta-rules like 'colour symmetry' and 'upside-down symmetry', which were considered as axioms in previous versions of the language, can in fact be derived. In particular, we show that the additional symbol and one of the rules which had been recently introduced to keep track of scalars (diagrams with no inputs or outputs are not necessary.

  18. Simplifying and extending R*-operation

    International Nuclear Information System (INIS)

    Chetyrkin, K.G.

    1987-04-01

    We describe how a recursive procedure to subtract all kinds of divergences (including the infrared ones) which can appear in a Euclidean Feynman integral - the R * -operation - can be both simplified and generalized by reformulating it in terms of the standard Bogoluibov-Parasiuk R-operation alone. The new formulation enjoys at least two advantages over the initial one. irst, it is applicable to evaluating ultraviolet divergences for arbitrary two-dimensional models - the problem which lies somewhat beyond the scope of the original version of the R * -operation. Second, with all qualifications about the pattern of external momenta being removed the reformulated R * -operation should be a convenient tool to treat asymptotic behaviour of an Euclidean Green function when some of its external momenta and/or masses tend to infinity. (orig.)

  19. Simplified discrete ordinates method in spherical geometry

    International Nuclear Information System (INIS)

    Elsawi, M.A.; Abdurrahman, N.M.; Yavuz, M.

    1999-01-01

    The authors extend the method of simplified discrete ordinates (SS N ) to spherical geometry. The motivation for such an extension is that the appearance of the angular derivative (redistribution) term in the spherical geometry transport equation makes it difficult to decide which differencing scheme best approximates this term. In the present method, the angular derivative term is treated implicitly and thus avoids the need for the approximation of such term. This method can be considered to be analytic in nature with the advantage of being free from spatial truncation errors from which most of the existing transport codes suffer. In addition, it treats the angular redistribution term implicitly with the advantage of avoiding approximations to that term. The method also can handle scattering in a very general manner with the advantage of spending almost the same computational effort for all scattering modes. Moreover, the methods can easily be applied to higher-order S N calculations

  20. Simplified model of a PWR primary circuit

    International Nuclear Information System (INIS)

    Souza, A.L.; Faya, A.J.G.

    1988-07-01

    The computer program RENUR was developed to perform a very simplified simulation of a typical PWR primary circuit. The program has mathematical models for the thermal-hydraulics of the reactor core and the pressurizer, the rest of the circuit being treated as a single volume. Heat conduction in the fuel rod is analyzed by a nodal model. Average and hot channels are treated so that bulk response of the core and DNBR can be evaluated. A homogenenous model is employed in the pressurizer. Results are presented for a steady-state situation as well as for a loss of load transient. Agreement with the results of more elaborate computer codes is good with substantial reduction in computer costs. (author) [pt

  1. RadCon Occurrence Reporting Simplified

    International Nuclear Information System (INIS)

    Denham, D. H.

    1999-01-01

    This narrative and accompanying diagrams provide a simplified summary of the RadCon Occurrence Reporting criteria to allow Environmental Restoration Contractor (ERC) staff to efficiently recognize occurrences and to effectively initiate the implementation of the requirements of U.S. Department of Energy (DOE) Order 232.1A, Occurrence Reporting and Processing of Operations Information, and of the ERC criteria defined in BHI-MA-02, ERC Project Procedures, Procedure 2.6, ''Occurrence Investigation and Reporting.'' These directives promote timely identification, categorization, notification, and reporting to DOE and ERC management of reportable occurrences at DOE-owned or -operated facilities that could (1) affect health and safety of the public, (2) seriously impact the intended purpose of DOE facilities, (3) adversely affect the credibility of DOE, or (4) have a noticeable adverse effect on the environment

  2. Simplified Model of Nonlinear Landau Damping

    International Nuclear Information System (INIS)

    Yampolsky, N.A.; Fisch, N.J.

    2009-01-01

    The nonlinear interaction of a plasma wave with resonant electrons results in a plateau in the electron distribution function close to the phase velocity of the plasma wave. As a result, Landau damping of the plasma wave vanishes and the resonant frequency of the plasma wave downshifts. However, this simple picture is invalid when the external driving force changes the plasma wave fast enough so that the plateau cannot be fully developed. A new model to describe amplification of the plasma wave including the saturation of Landau damping and the nonlinear frequency shift is proposed. The proposed model takes into account the change of the plasma wave amplitude and describes saturation of the Landau damping rate in terms of a single fluid equation, which simplifies the description of the inherently kinetic nature of Landau damping. A proposed fluid model, incorporating these simplifications, is verified numerically using a kinetic Vlasov code.

  3. Combustion Safety Simplified Test Protocol Field Study

    Energy Technology Data Exchange (ETDEWEB)

    Brand, L. [Gas Technology Inst., Des Plaines, IL (United States); Cautley, D. [Gas Technology Inst., Des Plaines, IL (United States); Bohac, D. [Gas Technology Inst., Des Plaines, IL (United States); Francisco, P. [Gas Technology Inst., Des Plaines, IL (United States); Shen, L. [Gas Technology Inst., Des Plaines, IL (United States); Gloss, S. [Gas Technology Inst., Des Plaines, IL (United States)

    2015-11-01

    Combustions safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives. A survey of state weatherization agencies on combustion safety issues, details of a field data collection instrumentation package, summary of data collected over seven months, data analysis and results are included. The project team collected field data on 11 houses in 2015.

  4. Development of small simplified modular reactors

    International Nuclear Information System (INIS)

    Hiki, Hideaki; Nakamaru, Mikihide

    2003-01-01

    The small simplified modular reactor, which is being development with matured BWR technologies together with innovative systems/components, will provide attractiveness for the energy market in the world due to its flexibility in energy demands as well as in site conditions, its high potential in reducing investment risk and its safety feature facilitating public acceptance. The flexibility is achieved by small output of 300 MWe and capability of long operating cycle (refueling intervals). The investment potential is expected from simplification/innovation in design such as natural circulation core cooling with the bottom located short core, internal upper entry control rod drives (CRDs) with ring-type dryers and hull structure building concept. The natural circulation core eliminates recirculation pumps as well as needs for maintenance of such pumps. The internal CRDs shorten the height of the reactor vessel (RPV) and consequently shorten the primary containment vessel (PCV). The hull structure facilitates modular arrangement, design standardization and factory fabrication. The safety feature mainly consists of large water inventory above the core without large penetration below the top of the core, passive containment cooling system (PCCS), passive auto-catalytic recombiner and in-vessel retention (IVR) capability. The large inventory increases the system response time in case of design base accidents including loss of coolant accidents. The PCCS suppresses PCV pressure by steam condensation without and AC power. The recombiner decreases hydrogen concentration in the PCV in case of a severe accident. The IVR could cool the molten core inside the RPV if the core should be damaged by loss of core coolability. These innovative systems/components featured in the small simplified modular reactor will stimulate global energy market. (author)

  5. Developing a simplified consent form for biobanking.

    Science.gov (United States)

    Beskow, Laura M; Friedman, Joëlle Y; Hardy, N Chantelle; Lin, Li; Weinfurt, Kevin P

    2010-10-08

    Consent forms have lengthened over time and become harder for participants to understand. We sought to demonstrate the feasibility of creating a simplified consent form for biobanking that comprises the minimum information necessary to meet ethical and regulatory requirements. We then gathered preliminary data concerning its content from hypothetical biobank participants. We followed basic principles of plain-language writing and incorporated into a 2-page form (not including the signature page) those elements of information required by federal regulations and recommended by best practice guidelines for biobanking. We then recruited diabetes patients from community-based practices and randomized half (n = 56) to read the 2-page form, first on paper and then a second time on a tablet computer. Participants were encouraged to use "More information" buttons on the electronic version whenever they had questions or desired further information. These buttons led to a series of "Frequently Asked Questions" (FAQs) that contained additional detailed information. Participants were asked to identify specific sentences in the FAQs they thought would be important if they were considering taking part in a biorepository. On average, participants identified 7 FAQ sentences as important (mean 6.6, SD 14.7, range: 0-71). No one sentence was highlighted by a majority of participants; further, 34 (60.7%) participants did not highlight any FAQ sentences. Our preliminary findings suggest that our 2-page form contains the information that most prospective participants identify as important. Combining simplified forms with supplemental material for those participants who desire more information could help minimize consent form length and complexity, allowing the most substantively material information to be better highlighted and enabling potential participants to read the form and ask questions more effectively.

  6. Stresses in a simplified two dimensional model of a normal foot : a preliminary analysis

    NARCIS (Netherlands)

    Patil, K.M.; Braak, L.H.; Huson, A.

    1993-01-01

    The loss of motor functions of the foot muscles in leprosy or diabetes changes the pattern of internal stresses in the foot skeleton. This may provoke local foci of relatively high stresses. In those cases where osteoporosis and cystic degeneration has weakened the mechanical strength of the bones,

  7. Limit cycle analysis of nuclear coupled density wave oscillations

    International Nuclear Information System (INIS)

    Ward, M.E.

    1985-01-01

    An investigation of limit cycle behavior for the nuclear-coupled density wave oscillation (NCDWO) in a boiling water reactor (BWR) was performed. A simplified nonlinear model of BWR core behavior was developed using a two-region flow channel representation, coupled with a form of the point-kinetics equation. This model has been used to investigate the behavior of large amplitude NCDWO's through conventional time-integration solutions and through application of a direct relaxation-oscillation limit cycle solution in phase space. The numerical solutions demonstrate the potential for severe global power and flow oscillations in a BWR core at off-normal conditions, such as might occur during Anticipated Transients without Scram. Because of the many simplifying assumptions used, it is felt that the results should not be interpreted as an absolute prediction of core behavior, but as an indication of the potential for large oscillations and a demonstration of the corresponding limit cycle mechanisms. The oscillations in channel density drive the core power variations, and are reinforced by heat flux variations due to the changing fuel temperature. A global temperature increase occurs as energy is accumulated in the fuel, and limits the magnitude of the oscillations because as the average channel density decreases, the amplitude and duration of positive void reactivity at a given oscillation amplitude is lessened

  8. Simplified Predictive Models for CO2 Sequestration Performance Assessment

    Science.gov (United States)

    Mishra, Srikanta; RaviGanesh, Priya; Schuetter, Jared; Mooney, Douglas; He, Jincong; Durlofsky, Louis

    2014-05-01

    We present results from an ongoing research project that seeks to develop and validate a portfolio of simplified modeling approaches that will enable rapid feasibility and risk assessment for CO2 sequestration in deep saline formation. The overall research goal is to provide tools for predicting: (a) injection well and formation pressure buildup, and (b) lateral and vertical CO2 plume migration. Simplified modeling approaches that are being developed in this research fall under three categories: (1) Simplified physics-based modeling (SPM), where only the most relevant physical processes are modeled, (2) Statistical-learning based modeling (SLM), where the simulator is replaced with a "response surface", and (3) Reduced-order method based modeling (RMM), where mathematical approximations reduce the computational burden. The system of interest is a single vertical well injecting supercritical CO2 into a 2-D layered reservoir-caprock system with variable layer permeabilities. In the first category (SPM), we use a set of well-designed full-physics compositional simulations to understand key processes and parameters affecting pressure propagation and buoyant plume migration. Based on these simulations, we have developed correlations for dimensionless injectivity as a function of the slope of fractional-flow curve, variance of layer permeability values, and the nature of vertical permeability arrangement. The same variables, along with a modified gravity number, can be used to develop a correlation for the total storage efficiency within the CO2 plume footprint. In the second category (SLM), we develop statistical "proxy models" using the simulation domain described previously with two different approaches: (a) classical Box-Behnken experimental design with a quadratic response surface fit, and (b) maximin Latin Hypercube sampling (LHS) based design with a Kriging metamodel fit using a quadratic trend and Gaussian correlation structure. For roughly the same number of

  9. SIMPLIFIED MATHEMATICAL MODEL OF SMALL SIZED UNMANNED AIRCRAFT VEHICLE LAYOUT

    Directory of Open Access Journals (Sweden)

    2016-01-01

    Full Text Available Strong reduction of new aircraft design period using new technology based on artificial intelligence is the key problem mentioned in forecasts of leading aerospace industry research centers. This article covers the approach to devel- opment of quick aerodynamic design methods based on artificial intelligence neural system. The problem is being solved for the classical scheme of small sized unmanned aircraft vehicle (UAV. The principal parts of the method are the mathe- matical model of layout, layout generator of this type of aircraft is built on aircraft neural networks, automatic selection module for cleaning variety of layouts generated in automatic mode, robust direct computational fluid dynamics method, aerodynamic characteristics approximators on artificial neural networks.Methods based on artificial neural networks have intermediate position between computational fluid dynamics methods or experiments and simplified engineering approaches. The use of ANN for estimating aerodynamic characteris-tics put limitations on input data. For this task the layout must be presented as a vector with dimension not exceeding sev-eral hundred. Vector components must include all main parameters conventionally used for layouts description and com- pletely replicate the most important aerodynamics and structural properties.The first stage of the work is presented in the paper. Simplified mathematical model of small sized UAV was developed. To estimate the range of geometrical parameters of layouts the review of existing vehicle was done. The result of the work is the algorithm and computer software for generating the layouts based on ANN technolo-gy. 10000 samples were generated and the dataset containig geometrical and aerodynamic characteristics of layoutwas created.

  10. A simplified approach for simulation of wake meandering

    Energy Technology Data Exchange (ETDEWEB)

    Thomsen, Kenneth; Aagaard Madsen, H.; Larsen, Gunner; Juul Larsen, T.

    2006-03-15

    This fact-sheet describes a simplified approach for a part of the recently developed dynamic wake model for aeroelastic simulations for wind turbines operating in wake. The part described in this fact-sheet concern the meandering process only, while the other part of the simplified approach the wake deficit profile is outside the scope of the present fact-sheet. Work on simplified models for the wake deficit profile is ongoing. (au)

  11. New weak keys in simplified IDEA

    Science.gov (United States)

    Hafman, Sari Agustini; Muhafidzah, Arini

    2016-02-01

    Simplified IDEA (S-IDEA) is simplified version of International Data Encryption Algorithm (IDEA) and useful teaching tool to help students to understand IDEA. In 2012, Muryanto and Hafman have found a weak key class in the S-IDEA by used differential characteristics in one-round (0, ν, 0, ν) → (0,0, ν, ν) on the first round to produce input difference (0,0, ν, ν) on the fifth round. Because Muryanto and Hafman only use three differential characteristics in one-round, we conducted a research to find new differential characteristics in one-round and used it to produce new weak key classes of S-IDEA. To find new differential characteristics in one-round of S-IDEA, we applied a multiplication mod 216+1 on input difference and combination of active sub key Z1, Z4, Z5, Z6. New classes of weak keys are obtained by combining all of these characteristics and use them to construct two new differential characteristics in full-round of S-IDEA with or without the 4th round sub key. In this research, we found six new differential characteristics in one round and combined them to construct two new differential characteristics in full-round of S-IDEA. When two new differential characteristics in full-round of S-IDEA are used and the 4th round sub key required, we obtain 2 new classes of weak keys, 213 and 28. When two new differential characteristics in full-round of S-IDEA are used, yet the 4th round sub key is not required, the weak key class of 213 will be 221 and 28 will be 210. Membership test can not be applied to recover the key bits in those weak key classes. The recovery of those unknown key bits can only be done by using brute force attack. The simulation result indicates that the bit of the key can be recovered by the longest computation time of 0,031 ms.

  12. The self-normalized Donsker theorem revisited

    OpenAIRE

    Parczewski, Peter

    2016-01-01

    We extend the Poincar\\'{e}--Borel lemma to a weak approximation of a Brownian motion via simple functionals of uniform distributions on n-spheres in the Skorokhod space $D([0,1])$. This approach is used to simplify the proof of the self-normalized Donsker theorem in Cs\\"{o}rg\\H{o} et al. (2003). Some notes on spheres with respect to $\\ell_p$-norms are given.

  13. Simplified probabilistic risk assessment in fuel reprocessing

    International Nuclear Information System (INIS)

    Solbrig, C.W.

    1993-01-01

    An evaluation was made to determine if a backup mass tracking computer would significantly reduce the probability of criticality in the fuel reprocessing of the Integral Fast Reactor. Often tradeoff studies, such as this, must be made that would greatly benefit from a Probably Risk Assessment (PRA). The major benefits of a complete PRA can often be accrued with a Simplified Probabilistic Risk Assessment (SPRA). An SPRA was performed by selecting a representative fuel reprocessing operation (moving a piece of fuel) for analysis. It showed that the benefit of adding parallel computers was small compared to the benefit which could be obtained by adding parallelism to two computer input steps and two of the weighing operations. The probability of an incorrect material moves with the basic process is estimated to be 4 out of 100 moves. The actual values of the probability numbers are considered accurate to within an order of magnitude. The most useful result of developing the fault trees accrue from the ability to determine where significant improvements in the process can be made. By including the above mentioned parallelism, the error move rate can be reduced to 1 out of 1000

  14. Simplified ejector model for control and optimization

    International Nuclear Information System (INIS)

    Zhu Yinhai; Cai Wenjian; Wen Changyun; Li Yanzhong

    2008-01-01

    In this paper, a simple yet effective ejector model for a real time control and optimization of an ejector system is proposed. Firstly, a fundamental model for calculation of ejector entrainment ratio at critical working conditions is derived by one-dimensional analysis and the shock circle model. Then, based on thermodynamic principles and the lumped parameter method, the fundamental ejector model is simplified to result in a hybrid ejector model. The model is very simple, which only requires two or three parameters and measurement of two variables to determine the ejector performance. Furthermore, the procedures for on line identification of the model parameters using linear and non-linear least squares methods are also presented. Compared with existing ejector models, the solution of the proposed model is much easier without coupled equations and iterative computations. Finally, the effectiveness of the proposed model is validated by published experimental data. Results show that the model is accurate and robust and gives a better match to the real performances of ejectors over the entire operating range than the existing models. This model is expected to have wide applications in real time control and optimization of ejector systems

  15. Simplified Dynamic Analysis of Grinders Spindle Node

    Science.gov (United States)

    Demec, Peter

    2014-12-01

    The contribution deals with the simplified dynamic analysis of surface grinding machine spindle node. Dynamic analysis is based on the use of the transfer matrix method, which is essentially a matrix form of method of initial parameters. The advantage of the described method, despite the seemingly complex mathematical apparatus, is primarily, that it does not require for solve the problem of costly commercial software using finite element method. All calculations can be made for example in MS Excel, which is advantageous especially in the initial stages of constructing of spindle node for the rapid assessment of the suitability its design. After detailing the entire structure of spindle node is then also necessary to perform the refined dynamic analysis in the environment of FEM, which it requires the necessary skills and experience and it is therefore economically difficult. This work was developed within grant project KEGA No. 023TUKE-4/2012 Creation of a comprehensive educational - teaching material for the article Production technique using a combination of traditional and modern information technology and e-learning.

  16. Simplified pressure method for respirator fit testing.

    Science.gov (United States)

    Han, D; Xu, M; Foo, S; Pilacinski, W; Willeke, K

    1991-08-01

    A simplified pressure method has been developed for fit testing air-purifying respirators. In this method, the air-purifying cartridges are replaced by a pressure-sensing attachment and a valve. While wearers hold their breath, a small pump extracts air from the respirator cavity until a steady-state pressure is reached in 1 to 2 sec. The flow rate through the face seal leak is a unique function of this pressure, which is determined once for all respirators, regardless of the respirator's cavity volume or deformation because of pliability. The contaminant concentration inside the respirator depends on the degree of dilution by the flow through the cartridges. The cartridge flow varies among different brands and is measured once for each brand. The ratio of cartridge to leakflow is a measure of fit. This flow ratio has been measured on human subjects and has been compared to fit factors determined on the same subjects by means of photometric and particle count tests. The aerosol tests gave higher values of fit.

  17. Simplified analysis of laterally loaded pile groups

    Directory of Open Access Journals (Sweden)

    F.M. Abdrabbo

    2012-06-01

    Full Text Available The response of laterally loaded pile groups is a complicated soil–structure interaction problem. Although fairly reliable methods are developed to predicate the lateral behavior of single piles, the lateral response of pile groups has attracted less attention due to the required high cost and complication implication. This study presents a simplified method to analyze laterally loaded pile groups. The proposed method implements p-multiplier factors in combination with the horizontal modulus of subgrade reaction. Shadowing effects in closely spaced piles in a group were taken into consideration. It is proven that laterally loaded piles embedded in sand can be analyzed within the working load range assuming a linear relationship between lateral load and lateral displacement. The proposed method estimates the distribution of lateral loads among piles in a pile group and predicts the safe design lateral load of a pile group. The benefit of the proposed method is in its simplicity for the preliminary design stage with a little computational effort.

  18. Simplified fuel cell system model identification

    Energy Technology Data Exchange (ETDEWEB)

    Caux, S.; Fadel, M. [Laboratoire d' Electrotechnique et d' Electronique Industrielle, Toulouse (France); Hankache, W. [Laboratoire d' Electrotechnique et d' Electronique Industrielle, Toulouse (France)]|[Laboratoire de recherche en Electronique, Electrotechnique et Systemes, Belfort (France); Hissel, D. [Laboratoire de recherche en Electronique, Electrotechnique et Systemes, Belfort (France)

    2006-07-01

    This paper discussed a simplified physical fuel cell model used to study fuel cell and supercap energy applications for vehicles. Anode, cathode, membrane, and electrode elements of the cell were modelled. A quasi-static Amphlett model was used to predict voltage responses of the fuel cell as a function of the current, temperature, and partial pressures of the reactive gases. The potential of each cell was multiplied by the number of cells in order to model a fuel cell stack. The model was used to describe the main phenomena associated with current voltage behaviour. Data were then compared with data from laboratory tests conducted on a 20 cell stack subjected to a current and time profile developed using speed data from a vehicle operating in an urban environment. The validated model was used to develop iterative optimization algorithms for an energy management strategy that linked 3 voltage sources with fuel cell parameters. It was concluded that classic state and dynamic measurements using a simple least square algorithm can be used to identify the most important parameters for optimal fuel cell operation. 9 refs., 1 tab., 6 figs.

  19. Combustion Safety Simplified Test Protocol Field Study

    Energy Technology Data Exchange (ETDEWEB)

    Brand, L [Gas Technology Inst., Des Plaines, IL (United States); Cautley, D. [Gas Technology Inst., Des Plaines, IL (United States); Bohac, D. [Gas Technology Inst., Des Plaines, IL (United States); Francisco, P. [Gas Technology Inst., Des Plaines, IL (United States); Shen, L. [Gas Technology Inst., Des Plaines, IL (United States); Gloss, S. [Gas Technology Inst., Des Plaines, IL (United States)

    2015-11-05

    "9Combustions safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives. A survey of state weatherization agencies on combustion safety issues, details of a field data collection instrumentation package, summary of data collected over seven months, data analysis and results are included. The project provides several key results. State weatherization agencies do not generally track combustion safety failures, the data from those that do suggest that there is little actual evidence that combustion safety failures due to spillage from non-dryer exhaust are common and that only a very small number of homes are subject to the failures. The project team collected field data on 11 houses in 2015. Of these homes, two houses that demonstrated prolonged and excessive spillage were also the only two with venting systems out of compliance with the National Fuel Gas Code. The remaining homes experienced spillage that only occasionally extended beyond the first minute of operation. Combustion zone depressurization, outdoor temperature, and operation of individual fans all provide statistically significant predictors of spillage.

  20. A simplified immunohistochemical classification of skeletal muscle fibres in mouse

    Directory of Open Access Journals (Sweden)

    M. Kammoun

    2014-06-01

    Full Text Available The classification of muscle fibres is of particular interest for the study of the skeletal muscle properties in a wide range of scientific fields, especially animal phenotyping. It is therefore important to define a reliable method for classifying fibre types. The aim of this study was to establish a simplified method for the immunohistochemical classification of fibres in mouse. To carry it out, we first tested a combination of several anti myosin heavy chain (MyHC antibodies in order to choose a minimum number of antibodies to implement a semi-automatic classification. Then, we compared the classification of fibres to the MyHC electrophoretic pattern on the same samples. Only two anti MyHC antibodies on serial sections with the fluorescent labeling of the Laminin were necessary to classify properly fibre types in Tibialis Anterior and Soleus mouse muscles in normal physiological conditions. This classification was virtually identical to the classification realized by the electrophoretic separation of MyHC. This immunohistochemical classification can be applied to the total area of Tibialis Anterior and Soleus mouse muscles. Thus, we provide here a useful, simple and time-efficient method for immunohistochemical classification of fibres, applicable for research in mouse

  1. A simplified CT-based definition of the lymph node levels in the node negative neck

    International Nuclear Information System (INIS)

    Wijers, O.B.; Levendag, P.C.; Tan, T.; Dieren, E.B. van; Sornsen de Koste, J. van; Est, H. van der; Senan, S.; Nowak, P.J.C.M.

    1999-01-01

    Using three dimensional (3D) conformal radiotherapy (CRT) techniques for elective neck irradiation (ENI) may allow for local disease control to be maintained while diminishing xerostomia by eliminating major salivary glands (or parts thereof) from the treatment portals. The standardization of CT based target volumes for the clinically negative (elective) neck is a prerequisite for 3DCRT. The aim of the present study was to substantially modify an existing ('original') CT-based protocol for the delineation of the neck tar-et volume, into a more practical ('simplified') protocol. This will allow for rapid contouring and the implementation of conformal ENI in routine clinical procedures. An earlier ('original') version of the CT-based definition for elective neck node re-ions 2-5 was re-evaluated, using 15 planning CT scans of previously treated patients. The contouring guidelines were simplified by (1) using a smaller number of easily identifiable soft tissue- and bony anatomical landmarks, which in turn had to be identified in only a limited number of CT slices, and (2) by subsequently interpolating the contoured lymph node regions. The adequacy of target coverage and the sparing using both 'original' and 'simplified' delineation protocols was evaluated by DVH analysis after contouring the primary tumor, the neck and the major salivary glands in a patient with supraglottic laryngeal (SGL) carcinoma who was treated using a 3DCRT technique. The BEV projections of the 'original' and the 'simplified' versions of the 3D elective neck target showed good agreement and were found to be reproducible. The DVH's of the target and parotid glands were not significantly different using both contouring protocols. The 'simplified' protocol for the delineation of the 3D elective neck target produced both comparable target coverage and sparing of the major salivary glands. When used together with an interpolation program, this 'simplified' protocol substantial reduced the contouring

  2. Seismic analysis of long tunnels: A review of simplified and unified methods

    Directory of Open Access Journals (Sweden)

    Haitao Yu

    2017-06-01

    Full Text Available Seismic analysis of long tunnels is important for safety evaluation of the tunnel structure during earthquakes. Simplified models of long tunnels are commonly adopted in seismic design by practitioners, in which the tunnel is usually assumed as a beam supported by the ground. These models can be conveniently used to obtain the overall response of the tunnel structure subjected to seismic loading. However, simplified methods are limited due to the assumptions that need to be made to reach the solution, e.g. shield tunnels are assembled with segments and bolts to form a lining ring and such structural details may not be included in the simplified model. In most cases, the design will require a numerical method that does not have the shortcomings of the analytical solutions, as it can consider the structural details, non-linear behavior, etc. Furthermore, long tunnels have significant length and pass through different strata. All of these would require large-scale seismic analysis of long tunnels with three-dimensional models, which is difficult due to the lack of available computing power. This paper introduces two types of methods for seismic analysis of long tunnels, namely simplified and unified methods. Several models, including the mass-spring-beam model, and the beam-spring model and its analytical solution are presented as examples of the simplified method. The unified method is based on a multiscale framework for long tunnels, with coarse and refined finite element meshes, or with the discrete element method and the finite difference method to compute the overall seismic response of the tunnel while including detailed dynamic response at positions of potential damage or of interest. A bridging scale term is introduced in the framework so that compatibility of dynamic behavior between the macro- and meso-scale subdomains is enforced. Examples are presented to demonstrate the applicability of the simplified and the unified methods.

  3. Simplified Freeman-Tukey test statistics for testing probabilities in ...

    African Journals Online (AJOL)

    This paper presents the simplified version of the Freeman-Tukey test statistic for testing hypothesis about multinomial probabilities in one, two and multidimensional contingency tables that does not require calculating the expected cell frequencies before test of significance. The simplified method established new criteria of ...

  4. 48 CFR 3032.003 - Simplified acquisition procedures financing.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Simplified acquisition procedures financing. 3032.003 Section 3032.003 Federal Acquisition Regulations System DEPARTMENT OF HOMELAND... FINANCING Scope of Part 3032.003 Simplified acquisition procedures financing. Contract financing may be...

  5. Communication: A simplified coupled-cluster Lagrangian for polarizable embedding.

    Science.gov (United States)

    Krause, Katharina; Klopper, Wim

    2016-01-28

    A simplified coupled-cluster Lagrangian, which is linear in the Lagrangian multipliers, is proposed for the coupled-cluster treatment of a quantum mechanical system in a polarizable environment. In the simplified approach, the amplitude equations are decoupled from the Lagrangian multipliers and the energy obtained from the projected coupled-cluster equation corresponds to a stationary point of the Lagrangian.

  6. Communication: A simplified coupled-cluster Lagrangian for polarizable embedding

    International Nuclear Information System (INIS)

    Krause, Katharina; Klopper, Wim

    2016-01-01

    A simplified coupled-cluster Lagrangian, which is linear in the Lagrangian multipliers, is proposed for the coupled-cluster treatment of a quantum mechanical system in a polarizable environment. In the simplified approach, the amplitude equations are decoupled from the Lagrangian multipliers and the energy obtained from the projected coupled-cluster equation corresponds to a stationary point of the Lagrangian

  7. A simplified method for assessing cytotechnologist workload.

    Science.gov (United States)

    Vaickus, Louis J; Tambouret, Rosemary

    2014-01-01

    Examining cytotechnologist workflow and how it relates to job performance and patient safety is important in determining guidelines governing allowable workloads. This report discusses the development of a software tool that significantly simplifies the process of analyzing cytotechnologist workload while simultaneously increasing the quantity and resolution of the data collected. The program runs in Microsoft Excel and minimizes manual data entry and data transcription by automating as many tasks as is feasible. Data show the cytotechnologists tested were remarkably consistent in the amount of time it took them to screen a cervical cytology (Gyn) or a nongynecologic cytology (Non-Gyn) case and that this amount of time was directly proportional to the number of slides per case. Namely, the time spent per slide did not differ significantly in Gyn versus Non-Gyn cases (216 ± 3.4 seconds and 235 ± 24.6 seconds, respectively; P=.16). There was no significant difference in the amount of time needed to complete a Gyn case between the morning and the evening (314 ± 4.7 seconds and 312 ± 7.1 seconds; P=.39), but a significantly increased time spent screening Non-Gyn cases (slide-adjusted) in the afternoon hours (323 ± 20.1 seconds and 454 ± 67.6 seconds; P=.027), which was largely the result of significantly increased time spent on prescreening activities such as checking the electronic medical record (62 ± 6.9 seconds and 145 ± 36 seconds; P=.006). This Excel-based data collection tool generates highly detailed data in an unobtrusive manner and is highly customizable to the individual working environment and clinical climate. © 2013 American Cancer Society.

  8. Conservatism inherent to simplified qualification techniques used for piping steady state vibration

    International Nuclear Information System (INIS)

    Olson, D.E.; Smetters, J.L.

    1983-01-01

    This paper examines some of the qualification techniques currently used by the power industry, including the techniques specified in a recently issued standard related to this subject (ANSI/ASME OM-3, Requirements for Preoperational and Initial Startup Vibration Testing of Nuclear Power Plant Piping Systems). Several methods are used to demonstrate the amount of conservatism inherent in these techniques. Allowable limits calculated by the use of simplified techniques are compared to limits calculated by more detailed computer analysis. A portion of a reactor feedwater piping system along with the results of a piping vibration monitoring program recently completed in a nuclear power plant are used as case studies. The limits determined by the use of simplified criteria are also compared to limits determined empirically through the use of strain gauges. The simple beam analogies that use vibrational displacement as acceptance criteria were found to be conservative for all the examples studied. However, when velocity was used as a criterion, it was not always conservative. Simplified techniques that result in displacement allowables appear to be the most viable method of qualifying piping vibrations. Quantities referred to in the paper are cited in British units throughout. These may be converted to the International System of Units (SI) as follows: 1 foot=0.3048 meter; 1 inch=0.0254 meter=1,000 mils; 1 psi=6,894 pascals; and 1 inch/second=0.0254 meter/second. (orig.)

  9. Robust test limits

    NARCIS (Netherlands)

    Albers, Willem/Wim; Kallenberg, W.C.M.; Otten, G.D.

    1997-01-01

    Because of inaccuracies of the measurement process inspection of manufactured parts requires test limits which are more strict than the given specification limits. Test limits derived under the assumption of normality for product characteristics turn out to violate the prescribed bound on the

  10. Stable crack growth behaviors in welded CT specimens -- finite element analyses and simplified assessments

    International Nuclear Information System (INIS)

    Yagawa, Genki; Yoshimura, Shinobu; Aoki, Shigeru; Kikuchi, Masanori; Arai, Yoshio; Kashima, Koichi; Watanabe, Takayuki; Shimakawa, Takashi

    1993-01-01

    The paper describes stable crack growth behaviors in welded CT specimens made of nuclear pressure vessel A533B class 1 steel, in which initial cracks are placed to be normal to fusion line. At first, using the relations between the load-line displacement (δ) and the crack extension amount (Δa) measured in experiments, the generation phase finite element crack growth analyses are performed, calculating the applied load (P) and various kinds of J-integrals. Next, the simplified crack growth analyses based on the GE/EPRI method and the reference stress method are performed using the same experimental results. Some modification procedures of the two simplified assessment schemes are discussed to make them applicable to inhomogeneous materials. Finally, a neural network approach is proposed to optimize the above modification procedures. 20 refs., 13 figs., 1 tab

  11. Normal Pressure Hydrocephalus (NPH)

    Science.gov (United States)

    ... local chapter Join our online community Normal Pressure Hydrocephalus (NPH) Normal pressure hydrocephalus is a brain disorder ... Symptoms Diagnosis Causes & risks Treatments About Normal Pressure Hydrocephalus Normal pressure hydrocephalus occurs when excess cerebrospinal fluid ...

  12. Simplified quantification of nicotinic receptors with 2[18F]F-A-85380 PET

    International Nuclear Information System (INIS)

    Mitkovski, Sascha; Villemagne, Victor L.; Novakovic, Kathy E.; O'Keefe, Graeme; Tochon-Danguy, Henri; Mulligan, Rachel S.; Dickinson, Kerryn L.; Saunder, Tim; Gregoire, Marie-Claude; Bottlaender, Michel; Dolle, Frederic; Rowe, Christopher C.

    2005-01-01

    Introduction: Neuronal nicotinic acetylcholine receptors (nAChRs), widely distributed in the human brain, are implicated in various neurophysiological processes as well as being particularly affected in neurodegenerative conditions such as Alzheimer's disease. We sought to evaluate a minimally invasive method for quantification of nAChR distribution in the normal human brain, suitable for routine clinical application, using 2[ 18 F]F-A-85380 and positron emission tomography (PET). Methods: Ten normal volunteers (four females and six males, aged 63.40±9.22 years) underwent a dynamic 120-min PET scan after injection of 226 MBq 2[ 18 F]F-A-85380 along with arterial blood sampling. Regional binding was assessed through standardized uptake value (SUV) and distribution volumes (DV) obtained using both compartmental (DV 2CM ) and graphical analysis (DV Logan ). A simplified approach to the estimation of DV (DV simplified ), defined as the region-to-plasma ratio at apparent steady state (90-120 min post injection), was compared with the other quantification approaches. Results: DV Logan values were higher than DV 2CM . A strong correlation was observed between DV simplified , DV Logan (r=.94) and DV 2CM (r=.90) in cortical regions, with lower correlations in thalamus (r=.71 and .82, respectively). Standardized uptake value showed low correlation against DV Logan and DV 2CM . Conclusion: DV simplified determined by the ratio of tissue to metabolite-corrected plasma using a single 90- to 120-min PET acquisition appears acceptable for quantification of cortical nAChR binding with 2[ 18 F]F-A-85380 and suitable for clinical application

  13. Simplified Models for Dark Matter and Missing Energy Searches at the LHC

    Energy Technology Data Exchange (ETDEWEB)

    Abdallah, Jalal [Academia Sinica, Taipei (Taiwan). Inst. of Physics; Ashkenazi, Adi [Tel Aviv Univ. (Israel). Dept. of Physics; Boveia, Antonio [Univ. of Chicago, IL (United States). Enrico Fermi Inst.; Busoni, Giorgio [International School for Advanced Studies (SISSA), Trieste (Italy); National Inst. for Nuclear Physics (INFN), Trieste (Italy); De Simone, Andrea [International School for Advanced Studies (SISSA), Trieste (Italy); National Inst. for Nuclear Physics (INFN), Trieste (Italy); Doglioni, Caterina [Univ. of Geneva (Switzerland). Physics Dept.; Efrati, Aielet [Weizmann Inst. of Science, Rehovot (Israel). Dept. of Particle Physics and Astrophysics; Etzion, Erez [Tel Aviv Univ. (Israel). Dept. of Physics; Gramling, Johanna [Univ. of Geneva (Switzerland). Physics Dept.; Jacques, Thomas [Univ. of Geneva (Switzerland). Physics Dept.; Lin, Tongyan [Univ. of Chicago, IL (United States). Kavli Inst. for Cosmological Physics. Enrico Fermi Inst.; Morgante, Enrico [Univ. of Geneva (Switzerland). Physics Dept.; Papucci, Michele [Univ. of California, Berkeley, CA (United States). Berkeley Center for Theoretical Physics; Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Theoretical Physics Group; Penning, Bjoern [Univ. of Chicago, IL (United States). Enrico Fermi Inst.; Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Riotto, Antonio Walter [Univ. of Geneva (Switzerland). Physics Dept.; Rizzo, Thomas [SLAC National Accelerator Lab., Menlo Park, CA (United States); Salek, David [National Inst. for Subatomic Physics (NIKHEF), Amsterdam (Netherlands); Gravitation and AstroParticle Physics in Amsterdam (GRAPPA), Amsterdam (Netherlands); Schramm, Steven [Univ. of Toronto, ON (Canada). Dept. of Physics; Slone, Oren [Tel Aviv Univ. (Israel). Dept. of Physics; Soreq, Yotam [Weizmann Inst. of Science, Rehovot (Israel). Dept. of Particle Physics and Astrophysics; Vichi, Alessandro [Univ. of California, Berkeley, CA (United States). Berkeley Center for Theoretical Physics; Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Theoretical Physics Group; Volansky, Tomer [Tel Aviv Univ. (Israel). Dept. of Physics; Yavin, Itay [Perimeter Inst. for Theoretical Physics, Waterloo, ON (Canada); McMaster Univ., Hamilton, ON (Canada). Dept. of Physics; Zhou, Ning [Univ. of California, Irvine, CA (United States). Dept. of Physics and Astronomy; Zurek, Kathryn [Univ. of California, Berkeley, CA (United States). Berkeley Center for Theoretical Physics; Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Theoretical Physics Group

    2014-10-01

    The study of collision events with missing energy as searches for the dark matter (DM) component of the Universe are an essential part of the extensive program looking for new physics at the LHC. Given the unknown nature of DM, the interpretation of such searches should be made broad and inclusive. This report reviews the usage of simplified models in the interpretation of missing energy searches. We begin with a brief discussion of the utility and limitation of the effective field theory approach to this problem. The bulk of the report is then devoted to several different simplified models and their signatures, including s-channel and t-channel processes. A common feature of simplified models for DM is the presence of additional particles that mediate the interactions between the Standard Model and the particle that makes up DM. We consider these in detail and emphasize the importance of their inclusion as final states in any coherent interpretation. We also review some of the experimental progress in the field, new signatures, and other aspects of the searches themselves. We conclude with comments and recommendations regarding the use of simplified models in Run-II of the LHC.

  14. Simplified Models for Dark Matter and Missing Energy Searches at the LHC

    International Nuclear Information System (INIS)

    Abdallah, Jalal; De Simone, Andrea; Doglioni, Caterina; Riotto, Antonio Walter; Salek, David; Schramm, Steven; Slone, Oren; Soreq, Yotam; Vichi, Alessandro; Lawrence Berkeley National Lab.; Volansky, Tomer; Yavin, Itay; McMaster Univ., Hamilton, ON; Zhou, Ning; Zurek, Kathryn; Lawrence Berkeley National Lab.

    2014-01-01

    The study of collision events with missing energy as searches for the dark matter (DM) component of the Universe are an essential part of the extensive program looking for new physics at the LHC. Given the unknown nature of DM, the interpretation of such searches should be made broad and inclusive. This report reviews the usage of simplified models in the interpretation of missing energy searches. We begin with a brief discussion of the utility and limitation of the effective field theory approach to this problem. The bulk of the report is then devoted to several different simplified models and their signatures, including s-channel and t-channel processes. A common feature of simplified models for DM is the presence of additional particles that mediate the interactions between the Standard Model and the particle that makes up DM. We consider these in detail and emphasize the importance of their inclusion as final states in any coherent interpretation. We also review some of the experimental progress in the field, new signatures, and other aspects of the searches themselves. We conclude with comments and recommendations regarding the use of simplified models in Run-II of the LHC.

  15. "A Simplified 'Benchmark” Stock-flow Consistent (SFC) Post-Keynesian Growth Model"

    OpenAIRE

    Claudio H. Dos Santos; Gennaro Zezza

    2007-01-01

    Despite being arguably one of the most active areas of research in heterodox macroeconomics, the study of the dynamic properties of stock-flow consistent (SFC) growth models of financially sophisticated economies is still in its early stages. This paper attempts to offer a contribution to this line of research by presenting a simplified Post-Keynesian SFC growth model with well-defined dynamic properties, and using it to shed light on the merits and limitations of the current heterodox SFC li...

  16. RF Breakdown in Normal Conducting Single-Cell Structures

    International Nuclear Information System (INIS)

    Dolgashev, V.A.; Nantista, C.D.; Tantawi, S.G.; Higashi, Y.; Higo, T.

    2006-01-01

    Operating accelerating gradient in normal conducting accelerating structures is often limited by rf breakdown. The limit depends on multiple parameters, including input rf power, rf circuit, cavity shape and material. Experimental and theoretical study of the effects of these parameters on the breakdown limit in full scale structures is difficult and costly. We use 11.4 GHz single-cell traveling wave and standing wave accelerating structures for experiments and modeling of rf breakdown behavior. These test structures are designed so that the electromagnetic fields in one cell mimic the fields in prototype multicell structures for the X-band linear collider. Fields elsewhere in the test structures are significantly lower than that of the single cell. The setup uses matched mode converters that launch the circular TM 01 mode into short test structures. The test structures are connected to the mode launchers with vacuum rf flanges. This setup allows economic testing of different cell geometries, cell materials and preparation techniques with short turn-around time. Simple 2D geometry of the test structures simplifies modeling of the breakdown currents and their thermal effects

  17. Simplified Entropic Model for the Evaluation of Suspended Load Concentration

    Directory of Open Access Journals (Sweden)

    Domenica Mirauda

    2018-03-01

    Full Text Available Suspended sediment concentration is a key aspect in the forecasting of river evolution dynamics, as well as in water quality assessment, evaluation of reservoir impacts, and management of water resources. The estimation of suspended load often relies on empirical models, of which efficiency is limited by their analytic structure or by the need for calibration parameters. The present work deals with a simplified fully-analytical formulation of the so-called entropic model in order to reproduce the vertical distribution of sediment concentration. The simplification consists in the leading order expansion of the generalized spatial coordinate of the entropic velocity profile that, strictly speaking, applies to the near-bed region, but that provides acceptable results also near the free surface. The proposed closed-form solution, which highlights the interplay among channel morphology, stream power, secondary flows, and suspended transport features, allows reducing the needed number of field measurements and, therefore, the time of field activities. Its accuracy and robustness were successfully tested based on the comparison with laboratory data reported in literature.

  18. River predisposition to ice jams: a simplified geospatial model

    Directory of Open Access Journals (Sweden)

    S. De Munck

    2017-07-01

    Full Text Available Floods resulting from river ice jams pose a great risk to many riverside municipalities in Canada. The location of an ice jam is mainly influenced by channel morphology. The goal of this work was therefore to develop a simplified geospatial model to estimate the predisposition of a river channel to ice jams. Rather than predicting the timing of river ice breakup, the main question here was to predict where the broken ice is susceptible to jam based on the river's geomorphological characteristics. Thus, six parameters referred to potential causes for ice jams in the literature were initially selected: presence of an island, narrowing of the channel, high sinuosity, presence of a bridge, confluence of rivers, and slope break. A GIS-based tool was used to generate the aforementioned factors over regular-spaced segments along the entire channel using available geospatial data. An ice jam predisposition index (IJPI was calculated by combining the weighted optimal factors. Three Canadian rivers (province of Québec were chosen as test sites. The resulting maps were assessed from historical observations and local knowledge. Results show that 77 % of the observed ice jam sites on record occurred in river sections that the model considered as having high or medium predisposition. This leaves 23 % of false negative errors (missed occurrence. Between 7 and 11 % of the highly predisposed river sections did not have an ice jam on record (false-positive cases. Results, limitations, and potential improvements are discussed.

  19. A highly simplified 3D BWR benchmark problem

    International Nuclear Information System (INIS)

    Douglass, Steven; Rahnema, Farzad

    2010-01-01

    The resurgent interest in reactor development associated with the nuclear renaissance has paralleled significant advancements in computer technology, and allowed for unprecedented computational power to be applied to the numerical solution of neutron transport problems. The current generation of core-level solvers relies on a variety of approximate methods (e.g. nodal diffusion theory, spatial homogenization) to efficiently solve reactor problems with limited computer power; however, in recent years, the increased availability of high-performance computer systems has created an interest in the development of new methods and codes (deterministic and Monte Carlo) to directly solve whole-core reactor problems with full heterogeneity (lattice and core level). This paper presents the development of a highly simplified heterogeneous 3D benchmark problem with physics characteristic of boiling water reactors. The aim of this work is to provide a problem for developers to use to validate new whole-core methods and codes which take advantage of the advanced computational capabilities that are now available. Additionally, eigenvalues and an overview of the pin fission density distribution are provided for the benefit of the reader. (author)

  20. Generic simplified simulation model for DFIG with active crowbar

    Energy Technology Data Exchange (ETDEWEB)

    Buendia, Francisco Jimenez [Gamesa Innovation and Technology, Sarriguren, Navarra (Spain). Technology Dept.; Barrasa Gordo, Borja [Assystem Iberia, Bilbao, Vizcaya (Spain)

    2012-07-01

    Simplified models for transient stability studies are a general requirement for transmission system operators to wind turbine (WTG) manufacturers. Those models must represent the performance of the WTGs for transient stability studies, mainly voltage dips originated by short circuits in the electrical network. Those models are implemented in simulation software as PSS/E, DigSilent or PSLF. Those software platforms allow simulation of transients in large electrical networks with thousands of busses, generators and loads. The high complexity of the grid requires that the models inserted into the grid should be simplified in order to allow the simulations being executed as fast as possible. The development of a model which is simplified enough to be integrated in those complex grids and represent the performance of WTG is a challenge. The IEC TC88 working group has developed generic models for different types of generators, among others for WTGs using doubly fed induction generators (DFIG). This paper will focus in an extension of the models for DFIG WTGs developed in IEC in order to be able to represent the simplified model of DFIG with an active crowbar, which is required to withstand voltage dips without disconnecting from the grid. This paper improves current generic model of Type 3 for DFIG adding a simplified version of the generator including crowbar functionality and a simplified version of the crowbar firing. In addition, this simplified model is validated by correlation with voltage dip field test from a real wind turbine. (orig.)

  1. Simplified Models for Dark Matter Searches at the LHC

    CERN Document Server

    Abdallah, Jalal; Arbey, Alexandre; Ashkenazi, Adi; Belyaev, Alexander; Berger, Joshua; Boehm, Celine; Boveia, Antonio; Brennan, Amelia; Brooke, Jim; Buchmueller, Oliver; Buckley, Matthew; Busoni, Giorgio; Calibbi, Lorenzo; Chauhan, Sushil; Daci, Nadir; Davies, Gavin; De Bruyn, Isabelle; de Jong, Paul; De Roeck, Albert; de Vries, Kees; del Re, Daniele; De Simone, Andrea; Di Simone, Andrea; Doglioni, Caterina; Dolan, Matthew; Dreiner, Herbi K.; Ellis, John; Eno, Sarah; Etzion, Erez; Fairbairn, Malcolm; Feldstein, Brian; Flaecher, Henning; Feng, Eric; Fox, Patrick; Genest, Marie-Hélène; Gouskos, Loukas; Gramling, Johanna; Haisch, Ulrich; Harnik, Roni; Hibbs, Anthony; Hoh, Siewyan; Hopkins, Walter; Ippolito, Valerio; Jacques, Thomas; Kahlhoefer, Felix; Khoze, Valentin V.; Kirk, Russell; Korn, Andreas; Kotov, Khristian; Kunori, Shuichi; Landsberg, Greg; Liem, Sebastian; Lin, Tongyan; Lowette, Steven; Lucas, Robyn; Malgeri, Luca; Malik, Sarah; McCabe, Christopher; Mete, Alaettin Serhan; Morgante, Enrico; Mrenna, Stephen; Nakahama, Yu; Newbold, Dave; Nordstrom, Karl; Pani, Priscilla; Papucci, Michele; Pataraia, Sophio; Penning, Bjoern; Pinna, Deborah; Polesello, Giacomo; Racco, Davide; Re, Emanuele; Riotto, Antonio Walter; Rizzo, Thomas; Salek, David; Sarkar, Subir; Schramm, Steven; Skubic, Patrick; Slone, Oren; Smirnov, Juri; Soreq, Yotam; Sumner, Timothy; Tait, Tim M.P.; Thomas, Marc; Tomalin, Ian; Tunnell, Christopher; Vichi, Alessandro; Volansky, Tomer; Weiner, Neal; West, Stephen M.; Wielers, Monika; Worm, Steven; Yavin, Itay; Zaldivar, Bryan; Zhou, Ning; Zurek, Kathryn

    2015-01-01

    This document outlines a set of simplified models for dark matter and its interactions with Standard Model particles. It is intended to summarize the main characteristics that these simplified models have when applied to dark matter searches at the LHC, and to provide a number of useful expressions for reference. The list of models includes both s-channel and t-channel scenarios. For s-channel, spin-0 and spin-1 mediation is discussed, and also realizations where the Higgs particle provides a portal between the dark and visible sectors. The guiding principles underpinning the proposed simplified models are spelled out, and some suggestions for implementation are presented.

  2. Simplified models for dark matter face their consistent completions

    Energy Technology Data Exchange (ETDEWEB)

    Gonçalves, Dorival; Machado, Pedro A. N.; No, Jose Miguel

    2017-03-01

    Simplified dark matter models have been recently advocated as a powerful tool to exploit the complementarity between dark matter direct detection, indirect detection and LHC experimental probes. Focusing on pseudoscalar mediators between the dark and visible sectors, we show that the simplified dark matter model phenomenology departs significantly from that of consistent ${SU(2)_{\\mathrm{L}} \\times U(1)_{\\mathrm{Y}}}$ gauge invariant completions. We discuss the key physics simplified models fail to capture, and its impact on LHC searches. Notably, we show that resonant mono-Z searches provide competitive sensitivities to standard mono-jet analyses at $13$ TeV LHC.

  3. Simplified models for dark matter searches at the LHC

    Energy Technology Data Exchange (ETDEWEB)

    Abdallah, Jalal; Araujo, Henrique; Arbey, Alexandre; Ashkenazi, Adi; Belyaev, Alexander; Berger, Joshua; Boehm, Celine; Boveia, Antonio; Brennan, Amelia; Brooke, Jim; Buchmueller, Oliver; Buckley, Matthew; Busoni, Giorgio; Calibbi, Lorenzo; Chauhan, Sushil; Daci, Nadir; Davies, Gavin; De Bruyn, Isabelle; De Jong, Paul; De Roeck, Albert; de Vries, Kees; Del Re, Daniele; De Simone, Andrea; Di Simone, Andrea; Doglioni, Caterina; Dolan, Matthew; Dreiner, Herbi K.; Ellis, John; Eno, Sarah; Etzion, Erez; Fairbairn, Malcolm; Feldstein, Brian; Flaecher, Henning; Feng, Eric; Fox, Patrick; Genest, Marie-Hélène; Gouskos, Loukas; Gramling, Johanna; Haisch, Ulrich; Harnik, Roni; Hibbs, Anthony; Hoh, Siewyan; Hopkins, Walter; Ippolito, Valerio; Jacques, Thomas; Kahlhoefer, Felix; Khoze, Valentin V.; Kirk, Russell; Korn, Andreas; Kotov, Khristian; Kunori, Shuichi; Landsberg, Greg; Liem, Sebastian; Lin, Tongyan; Lowette, Steven; Lucas, Robyn; Malgeri, Luca; Malik, Sarah; McCabe, Christopher; Mete, Alaettin Serhan; Morgante, Enrico; Mrenna, Stephen; Nakahama, Yu; Newbold, Dave; Nordstrom, Karl; Pani, Priscilla; Papucci, Michele; Pataraia, Sophio; Penning, Bjoern; Pinna, Deborah; Polesello, Giacomo; Racco, Davide; Re, Emanuele; Riotto, Antonio Walter; Rizzo, Thomas; Salek, David; Sarkar, Subir; Schramm, Steven; Skubic, Patrick; Slone, Oren; Smirnov, Juri; Soreq, Yotam; Sumner, Timothy; Tait, Tim M. P.; Thomas, Marc; Tomalin, Ian; Tunnell, Christopher; Vichi, Alessandro; Volansky, Tomer; Weiner, Neal; West, Stephen M.; Wielers, Monika; Worm, Steven; Yavin, Itay; Zaldivar, Bryan; Zhou, Ning; Zurek, Kathryn

    2015-09-01

    This document a outlines a set of simplified models for dark matter and its interactions with Standard Model particles. It is intended to summarize the main characteristics that these simplified models have when applied to dark matter searches at the LHC, and to provide a number of useful expressions for reference. The list of models includes both s-channel and t-channel scenarios. For s-channel, spin-0 and spin-1 mediations are discussed, and also realizations where the Higgs particle provides a portal between the dark and visible sectors. The guiding principles underpinning the proposed simplified models are spelled out, and some suggestions for implementation are presented.

  4. Simplified method evaluation for piping elastic follow-up

    International Nuclear Information System (INIS)

    Severud, L.K.

    1983-05-01

    A proposed simplified method for evaluating elastic follow-up effects in high temperature pipelines is presented. The method was evaluated by comparing the simplified analysis results with those obtained from detailed inelastic solutions. Nine different pipelines typical of a nuclear breeder reactor power plant were analyzed; the simplified method is attractive because it appears to give fairly accurate and conservative results. It is easy to apply and inexpensive since it employs iterative elastic solutions for the pipeline coupled with the readily available isochronous stress-strain data provided in the ASME Code

  5. A simplified approach for the coupling of excitation energy transfer

    Energy Technology Data Exchange (ETDEWEB)

    Shi Bo [Hefei National Laboratory for Physical Science at Microscale, University of Science and Technology of China, Hefei 230026 (China); Department of Chemical Physics, University of Science and Technology of China, Hefei 230026 (China); Gao Fang, E-mail: gaofang@iim.ac.cn [Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China); State Key Laboratory of Robotics, Shenyang Institute of Automation, Chinese Academy of Sciences, Shenyang 110016 (China); Liang Wanzhen [Hefei National Laboratory for Physical Science at Microscale, University of Science and Technology of China, Hefei 230026 (China); Department of Chemical Physics, University of Science and Technology of China, Hefei 230026 (China)

    2012-02-06

    Highlights: Black-Right-Pointing-Pointer We propose a simple method to calculate the coupling of singlet-to-singlet and triplet-to-triplet energy transfer. Black-Right-Pointing-Pointer Coulomb term are the major contribution to the coupling of singlet-to-singlet energy transfer. Black-Right-Pointing-Pointer Effect from the intermolecular charge-transfer states dorminates in triplet-to-triplet energy transfer. Black-Right-Pointing-Pointer This method can be expanded by including correlated wavefunctions. - Abstract: A simplified approach for computing the electronic coupling of nonradiative excitation-energy transfer is proposed by following Scholes et al.'s construction on the initial and final states [G.D. Scholes, R.D. Harcourt, K.P. Ghiggino, J. Chem. Phys. 102 (1995) 9574]. The simplification is realized through defining a set of orthogonalized localized MOs, which include the polarization effect of the charge densities. The method allows calculating the coupling of both the singlet-to-singlet and triplet-to-triplet energy transfer. Numerical tests are performed for a few of dimers with different intermolecular orientations, and the results demonstrate that Coulomb term are the major contribution to the coupling of singlet-to-singlet energy transfer whereas in the case of triplet-to-triplet energy transfer, the dominant effect is arisen from the intermolecular charge-transfer states. The present application is on the Hartree-Fock level. However, the correlated wavefunctions which are normally expanded in terms of the determinant wavefunctions can be employed in the similar way.

  6. Normalization: A Preprocessing Stage

    OpenAIRE

    Patro, S. Gopal Krishna; Sahu, Kishore Kumar

    2015-01-01

    As we know that the normalization is a pre-processing stage of any type problem statement. Especially normalization takes important role in the field of soft computing, cloud computing etc. for manipulation of data like scale down or scale up the range of data before it becomes used for further stage. There are so many normalization techniques are there namely Min-Max normalization, Z-score normalization and Decimal scaling normalization. So by referring these normalization techniques we are ...

  7. A simplified method of power calibration

    International Nuclear Information System (INIS)

    Jones, M.; Elliott, A.

    1974-01-01

    The Nuclear Reactor Facility, University of Missouri Rolla, has developed a unique method of power calibration for pool type reactors. Since water is incompressible it can be assumed that a rise in the water level of the pool while operating at power can be attributed to the heat input from the reactor core. Water level changes of a small magnitude are easily detectable. This method has proven to be less costly, less time consuming, and more reproducible than the conventional gold foil calibration, and has proven to be more accurate than a heat balance because several problems with heat flow through the walls and to the atmosphere are automatically compensated for with this method. The accuracy of this means of calibration depends upon the accuracy of the measurement of the water level and can normally be expected to be two to four percent. (author)

  8. A simplified method of power calibration

    Energy Technology Data Exchange (ETDEWEB)

    Jones, M; Elliott, A [University of Missouri-Rolla (United States)

    1974-07-01

    The Nuclear Reactor Facility, University of Missouri Rolla, has developed a unique method of power calibration for pool type reactors. Since water is incompressible it can be assumed that a rise in the water level of the pool while operating at power can be attributed to the heat input from the reactor core. Water level changes of a small magnitude are easily detectable. This method has proven to be less costly, less time consuming, and more reproducible than the conventional gold foil calibration, and has proven to be more accurate than a heat balance because several problems with heat flow through the walls and to the atmosphere are automatically compensated for with this method. The accuracy of this means of calibration depends upon the accuracy of the measurement of the water level and can normally be expected to be two to four percent. (author)

  9. Simplified correction of g-value measurements

    DEFF Research Database (Denmark)

    Duer, Karsten

    1998-01-01

    been carried out using a detailed physical model based on ISO9050 and prEN410 but using polarized data for non-normal incidence. This model is only valid for plane, clear glazings and therefor not suited for corrections of measurements performed on complex glazings. To investigate a more general...... correction procedure the results from the measurements on the Interpane DGU have been corrected using the principle outlined in (Rosenfeld, 1996). This correction procedure is more general as corrections can be carried out without a correct physical model of the investigated glazing. On the other hand...... the way this “general” correction procedure is used is not always in accordance to the physical conditions....

  10. Conceptual design study on simplified and safer cooling systems for sodium cooled FBRs

    International Nuclear Information System (INIS)

    Hayafune, Hiroki; Shimakawa, Yoshio; Ishikawa, Hiroyasu; Kubota, Kenichi; Kobayashi, Jun; Kasai, Shigeo

    2000-06-01

    The objective of this study is to create the FBR plant concepts increasing economy and safety for the Phase-I 'Feasibility Studies on Commercialized Fast Reactor System'. In this study, various concepts of simplified 2ry cooling system for sodium cooled FBRs are considered and evaluated from the view points of technological feasibility, economy, and safety. The concepts in the study are considered on the basis of the following points of view. 1. To simplify 2ry cooling system by moderating and localizing the sodium-water reaction in the steam generator of the FBRs. 2. To simplify 2ry cooling system by eliminating the sodium-water reaction using integrated IHX-SG unit. 3. To simplify 2ry cooling system by eliminating the sodium-water reaction using a power generating system other than the steam generator. As the result of the study, 12 concepts and 3 innovative concepts are proposed. The evaluation study for those concepts shows the following technical prospects. 1. 2 concepts of integrated IHX-SG unit can eliminate the sodium-water reaction. Separated IHX and SG tubes unit using Lead-Bismuth as the heat transfer medium. Integrated IHX-SG unit using copper as the heat transfer medium. 2. Cost reduction effect by simplified 2ry cooling system using integrated IHX-SG unit is estimated 0 to 5%. 3. All of the integrated IHX-SG unit concepts have more weight and larger size than conventional steam generator unit. The weight of the unit during transporting and lifting would limit capacity of heat transfer system. These evaluation results will be compared with the results in JFY 2000 and used for the Phase-II study. (author)

  11. A simplified technique for shakedown load determination

    International Nuclear Information System (INIS)

    Abdalla, H.F.; Younan, M.Y.A.; Megahed, M.M.

    2005-01-01

    In this paper a simple technique is presented to determine the limit shakedown load of a structure or a component using the finite element method. Through the proposed technique, the limit shakedown load is determined without performing time consuming cyclic loading simulations or iterative elastic techniques. Instead, it is determined by performing only two analyses namely, an elastic analysis and an elastic-plastic analysis. By extracting the results of the two analyses, the limit shakedown load of the structure is determined through the calculation of the residual stresses. The technique is applied and verified using two bench mark shakedown problems namely: the two-bar structure subjected to constant axial force and cyclic thermal loading, and the Bree cylinder subjected to constant internal pressure and cyclic high heat fluxes across its wall. The results of the proposed technique showed very good correlation with the, analytically determined, Bree diagrams of both structures. Moreover, the outcomes of the proposed technique showed very good results in comparison to full cyclic loading elasto-plastic finite element simulations of both structures. (authors)

  12. Simplified Laboratory Runoff Procedure (SLRP): Procedure and Application

    National Research Council Canada - National Science Library

    Price, Richard

    2000-01-01

    The Simplified Laboratory Runoff Procedure (SLRP) was developed to provide a faster, less expensive approach to evaluate surface runoff water quality from dredged material placed in an upland environment...

  13. 48 CFR 32.003 - Simplified acquisition procedures financing.

    Science.gov (United States)

    2010-10-01

    ... procedures financing. 32.003 Section 32.003 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION GENERAL CONTRACTING REQUIREMENTS CONTRACT FINANCING 32.003 Simplified acquisition procedures financing. Unless agency regulations otherwise permit, contract financing shall not be provided for...

  14. A simplified method for processing dynamic images of gastric antrum

    DEFF Research Database (Denmark)

    Madsen, J L; Graff, J; Fugisang, S

    2000-01-01

    versus geometric centre curve. In all subjects, our technique gave unequivocal frequencies of antral contractions at each time point. Statistical analysis did not reveal any intraindividual variation in this frequency during gastric emptying. We believe that the simplified scintigraphic method...

  15. Webinar: Simplifying Sustainable Purchasing Through Guidelines and Standards

    Science.gov (United States)

    This webinar will cover EPA’s effort to simplify green purchasing through recommendations of specifications, standards, and ecolabels. EPA’s work in this area is intended to help federal purchasers identify and procure environmentally sustainable products.

  16. A simplified parsimonious higher order multivariate Markov chain model

    Science.gov (United States)

    Wang, Chao; Yang, Chuan-sheng

    2017-09-01

    In this paper, a simplified parsimonious higher-order multivariate Markov chain model (SPHOMMCM) is presented. Moreover, parameter estimation method of TPHOMMCM is give. Numerical experiments shows the effectiveness of TPHOMMCM.

  17. Photographic and drafting techniques simplify method of producing engineering drawings

    Science.gov (United States)

    Provisor, H.

    1968-01-01

    Combination of photographic and drafting techniques has been developed to simplify the preparation of three dimensional and dimetric engineering drawings. Conventional photographs can be converted to line drawings by making copy negatives on high contrast film.

  18. Optimization of an impact limiter for radioactive waste packaging

    International Nuclear Information System (INIS)

    Mourao, Rogerio Pimenta; Mattar Neto, Miguel

    1999-01-01

    A certain class of packages for the transportation of radioactive wastes - type B packages in the transport jargon - is supposed to resist to a series of postulated tests, the most severe for the majority of the packages being the 9 m height drop test. To improve the performance of the packages under this test, impact limiters are added to them, normally as a removable overpack, with the primary goal of reducing the deceleration loads transmitted to the packages and their contents. The first impact limiter concept, developed during the '70s, used a shell-type impact limiter attached to both ends of the package. Later on, wood was tested as impact limiter filling, which improved the package's mechanical performance, but not its thermal resistance. The popularization of the polymeric materials and their growing use in engineer applications have led to the use of these materials in impact limiters, with the extra advantage of the polymers good thermal properties. This paper proposes a methodology for the optimization of an impact limiter for a package for the conditioning of spent sealed sources. Two simplified methods for the design of impact limiters are presented. Finally, a brief discussion is presented on the methodology usually employed in the design of accident-resisting packages. (author)

  19. Limiting oxygen concentration for extinction of upward spreading flames over inclined thin polyethylene-insulated NiCr electrical wires with opposed-flow under normal- and micro-gravity

    KAUST Repository

    Hu, Longhua; Lu, Yong; Yoshioka, Kosuke; Zhang, Yangshu; Fernandez-Pello, Carlos; Chung, Suk-Ho; Fujita, Osamu

    2016-01-01

    . The experiments reported here used polyethylene (PE)-insulated (thickness of 0.15 mm) Nichrome (NiCr)-core (diameter of 0.5 mm) electrical wires. Limiting oxygen concentrations (LOC) at extinction were measured for upward spreading flame at various forced opposed-flow

  20. Simplified analysis of PRISM RVACS [Reactor Vessel Auxiliary Cooling System] performance without liner spill-over

    International Nuclear Information System (INIS)

    Van Tuyle, G.J.

    1990-01-01

    Simplified analysis of the performance of the PRISM RVACS decay heat removal system under off-normal conditions, i.e., without the liner spill-over, is described. Without the spilling of hot-pool sodium over the liner and the resultant down-flow along the inside of the reactor vessel wall, the RVACS system performance becomes dominated by the radial heat condition and radiation. Simple estimates of the resulting heat conduction and radiation processes support GE's contention that the RVACS performance is not severely impacted by the absence of spillover, and can improve significantly if sodium has leaked into the region between the reactor and containment vessels. 7 refs

  1. Alcohol and illicit drugs in drivers involved in road traffic crashes in the Milan area. A comparison with normal traffic reveals the possible inadequacy of current cut-off limits.

    Science.gov (United States)

    Ferrari, Davide; Manca, Monica; Banfi, Giuseppe; Locatelli, Massimo

    2018-01-01

    Driving under the influence of alcohol and/or illicit drugs in Italy is regulated by the articles 186 and 187 of the National Street Code. Epidemiological studies on drivers involved in road traffic crashes (RTC) provide useful information about the use/abuse of these substances in the general population. Comparison with case control studies may reveal important information like the cut-off limits adequacy. Data from 1587 blood tests for alcohol and 1258 blood tests for illicit drugs on drivers involved in RTC around Milan between 2012 and 2016, were analyzed and compared with a published random survey (DRUID) from the European Community. Our data from RTC-involved drivers show that alcohol abuse is not age-related whereas illicit drugs are more common in young people. Cannabinoids are frequent among younger drivers (median age 27) whereas cocaine is more often detected in adults (median age 34). The calculated odds ratio after comparison with the DRUID survey shows that a blood alcohol concentration below the legal limit does not represent a risk factor in having a car accident whereas concentrations of cocaine and cannabinoids within the legal limits are associated with being involved in a car accident. Despite authority efforts, the abuse of alcohol and illicit drugs is still common in young drivers. We suspect that the cut-off limits for cannabinoids and cocaine and/or the pre-analytical procedures for these substances are inadequate. We suggest a better standardization of the procedure by shortening the time interval between the request for investigation and blood collection and propose the adoption of more stringent cut-off limits. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Effect of normal processes on thermal conductivity of germanium ...

    Indian Academy of Sciences (India)

    Abstract. The effect of normal scattering processes is considered to redistribute the phonon momentum in (a) the same phonon branch – KK-S model and (b) between differ- ent phonon branches – KK-H model. Simplified thermal conductivity relations are used to estimate the thermal conductivity of germanium, silicon and ...

  3. SModelS v1.1 user manual: Improving simplified model constraints with efficiency maps

    Science.gov (United States)

    Ambrogi, Federico; Kraml, Sabine; Kulkarni, Suchita; Laa, Ursula; Lessa, Andre; Magerl, Veronika; Sonneveld, Jory; Traub, Michael; Waltenberger, Wolfgang

    2018-06-01

    SModelS is an automatized tool for the interpretation of simplified model results from the LHC. It allows to decompose models of new physics obeying a Z2 symmetry into simplified model components, and to compare these against a large database of experimental results. The first release of SModelS, v1.0, used only cross section upper limit maps provided by the experimental collaborations. In this new release, v1.1, we extend the functionality of SModelS to efficiency maps. This increases the constraining power of the software, as efficiency maps allow to combine contributions to the same signal region from different simplified models. Other new features of version 1.1 include likelihood and χ2 calculations, extended information on the topology coverage, an extended database of experimental results as well as major speed upgrades for both the code and the database. We describe in detail the concepts and procedures used in SModelS v1.1, explaining in particular how upper limits and efficiency map results are dealt with in parallel. Detailed instructions for code usage are also provided.

  4. Quantum annealing versus classical machine learning applied to a simplified computational biology problem

    Science.gov (United States)

    Li, Richard Y.; Di Felice, Rosa; Rohs, Remo; Lidar, Daniel A.

    2018-01-01

    Transcription factors regulate gene expression, but how these proteins recognize and specifically bind to their DNA targets is still debated. Machine learning models are effective means to reveal interaction mechanisms. Here we studied the ability of a quantum machine learning approach to predict binding specificity. Using simplified datasets of a small number of DNA sequences derived from actual binding affinity experiments, we trained a commercially available quantum annealer to classify and rank transcription factor binding. The results were compared to state-of-the-art classical approaches for the same simplified datasets, including simulated annealing, simulated quantum annealing, multiple linear regression, LASSO, and extreme gradient boosting. Despite technological limitations, we find a slight advantage in classification performance and nearly equal ranking performance using the quantum annealer for these fairly small training data sets. Thus, we propose that quantum annealing might be an effective method to implement machine learning for certain computational biology problems. PMID:29652405

  5. SUSY simplified models at 14, 33, and 100 TeV proton colliders

    International Nuclear Information System (INIS)

    Cohen, Timothy; Golling, Tobias; Hance, Mike; Henrichs, Anna; Howe, Kiel; Loyal, Joshua; Padhi, Sanjay; Wacker, Jay G.

    2014-01-01

    Results are presented for a variety of SUSY Simplified Models at the 14 TeV LHC as well as a 33 and 100 TeV proton collider. Our focus is on models whose signals are driven by colored production. We present projections of the upper limit and discovery reach in the gluino-neutralino (for both light and heavy flavor decays), squark-neutralino, and gluino-squark Simplified Model planes. Depending on the model a jets + E T miss , mono-jet, or same-sign di-lepton search is applied. The impact of pileup is explored. This study utilizes the Snowmass backgrounds and combined detector. Assuming 3000/,fb −1 of integrated luminosity, a gluino that decays to light flavor quarks can be discovered below 2.3 TeV at the 14 TeV LHC and below 11 TeV at a 100 TeV machine

  6. Boosting invisible searches via Z H : From the Higgs boson to dark matter simplified models

    Science.gov (United States)

    Gonçalves, Dorival; Krauss, Frank; Kuttimalai, Silvan; Maierhöfer, Philipp

    2016-09-01

    Higgs boson production in association with a Z boson at the LHC is analyzed, both in the Standard Model and in simplified model extensions for dark matter. We focus on H →invisibles searches and show that loop-induced components for both the signal and background present phenomenologically relevant contributions to the B R (H →inv) limits. We also show how multijet merging improves the description of key distributions to this analysis. In addition, the constraining power of this channel to simplified models for dark matter with scalar and pseudoscalar mediators ϕ and A is discussed and compared with noncollider constraints. We find that with 100 fb-1 of LHC data, this channel provides competitive constraints to the noncollider bounds, for most of the parameter space we consider, bounding the universal Standard Model fermion-mediator strength at gvmoderate masses in the range of 100 GeV

  7. Quantum annealing versus classical machine learning applied to a simplified computational biology problem

    Science.gov (United States)

    Li, Richard Y.; Di Felice, Rosa; Rohs, Remo; Lidar, Daniel A.

    2018-03-01

    Transcription factors regulate gene expression, but how these proteins recognize and specifically bind to their DNA targets is still debated. Machine learning models are effective means to reveal interaction mechanisms. Here we studied the ability of a quantum machine learning approach to classify and rank binding affinities. Using simplified data sets of a small number of DNA sequences derived from actual binding affinity experiments, we trained a commercially available quantum annealer to classify and rank transcription factor binding. The results were compared to state-of-the-art classical approaches for the same simplified data sets, including simulated annealing, simulated quantum annealing, multiple linear regression, LASSO, and extreme gradient boosting. Despite technological limitations, we find a slight advantage in classification performance and nearly equal ranking performance using the quantum annealer for these fairly small training data sets. Thus, we propose that quantum annealing might be an effective method to implement machine learning for certain computational biology problems.

  8. Simplified absolute phase retrieval of dual-frequency fringe patterns in fringe projection profilometry

    Science.gov (United States)

    Lu, Jin; Mo, Rong; Sun, Huibin; Chang, Zhiyong; Zhao, Xiaxia

    2016-04-01

    In fringe projection profilometry, a simplified method is proposed to recover absolute phase maps of two-frequency fringe patterns by using a unique mapping rule. The mapping rule is designed from the rounded phase values to the fringe order of each pixel. Absolute phase can be recovered by the fringe order maps. Unlike the existing techniques, where the lowest frequency of dual- or multiple-frequency fringe patterns must be single, the presented method breaks the limitation and simplifies the procedure of phase unwrapping. Additionally, due to many issues including ambient light, shadow, sharp edges, step height boundaries and surface reflectivity variations, a novel framework of automatically identifying and removing invalid phase values is also proposed. Simulations and experiments have been carried out to validate the performances of the proposed method.

  9. Simplifying dynamic river water quality modelling: A case study of inorganic nitrogen dynamics in the Crocodile River (South Africa).

    CSIR Research Space (South Africa)

    Deksissa, T

    2004-06-01

    Full Text Available Quality Model No. 1, which is one of the most comprehensive basic river water quality models available in literature. The applicability of the simplified model in data limited situations was investigated using a case study of inorganic nitrogen (nitrate...

  10. Simplified method of ''push-pull'' test data analysis for determining in situ reaction rate coefficients

    International Nuclear Information System (INIS)

    Haggerty, R.; Schroth, M.H.; Istok, J.D.

    1998-01-01

    The single-well, ''''push-pull'''' test method is useful for obtaining information on a wide variety of aquifer physical, chemical, and microbiological characteristics. A push-pull test consists of the pulse-type injection of a prepared test solution into a single monitoring well followed by the extraction of the test solution/ground water mixture from the same well. The test solution contains a conservative tracer and one or more reactants selected to investigate a particular process. During the extraction phase, the concentrations of tracer, reactants, and possible reaction products are measured to obtain breakthrough curves for all solutes. This paper presents a simplified method of data analysis that can be used to estimate a first-order reaction rate coefficient from these breakthrough curves. Rate coefficients are obtained by fitting a regression line to a plot of normalized concentrations versus elapsed time, requiring no knowledge of aquifer porosity, dispersivity, or hydraulic conductivity. A semi-analytical solution to the advective-dispersion equation is derived and used in a sensitivity analysis to evaluate the ability of the simplified method to estimate reaction rate coefficients in simulated push-pull tests in a homogeneous, confined aquifer with a fully-penetrating injection/extraction well and varying porosity, dispersivity, test duration, and reaction rate. A numerical flow and transport code (SUTRA) is used to evaluate the ability of the simplified method to estimate reaction rate coefficients in simulated push-pull tests in a heterogeneous, unconfined aquifer with a partially penetrating well. In all cases the simplified method provides accurate estimates of reaction rate coefficients; estimation errors ranged from 0.1 to 8.9% with most errors less than 5%

  11. On a simplified inelastic analysis of structures

    International Nuclear Information System (INIS)

    Zarka, J.; Engel, J.J.; Inglebert, G.

    1980-01-01

    In this paper two main problems are considered: the derivation of cyclic constitutive relations during inelastic regime where hardening, softening and creep can occur, and the development of the eventual periodical state in the structure during cyclic thermodynamical loadings. We give a very simple and practical framework to solve these problems in one unique manner. Its essential feature consits in the introduction of a family of internal parameters which characterize local inelastic mechanisms and the family of transformed internal parameters which are linearly linked to the previous ones through a symmetrical non-negative matrix and are indeed the opposite of the associated residual stresses. Thanks to that, the treatment of the local plastic or viscoplastic yield conditions can be easily made from only the classical simple purely elastic (or viscoelastic) analysis. This property allows important results during cyclic loadings: conditions for elastic shakedown, plastic shakedown, ratcheting and bounds for the limiting state. Several examples are given in the text. (orig.)

  12. Artificial cell mimics as simplified models for the study of cell biology.

    Science.gov (United States)

    Salehi-Reyhani, Ali; Ces, Oscar; Elani, Yuval

    2017-07-01

    Living cells are hugely complex chemical systems composed of a milieu of distinct chemical species (including DNA, proteins, lipids, and metabolites) interconnected with one another through a vast web of interactions: this complexity renders the study of cell biology in a quantitative and systematic manner a difficult task. There has been an increasing drive towards the utilization of artificial cells as cell mimics to alleviate this, a development that has been aided by recent advances in artificial cell construction. Cell mimics are simplified cell-like structures, composed from the bottom-up with precisely defined and tunable compositions. They allow specific facets of cell biology to be studied in isolation, in a simplified environment where control of variables can be achieved without interference from a living and responsive cell. This mini-review outlines the core principles of this approach and surveys recent key investigations that use cell mimics to address a wide range of biological questions. It will also place the field in the context of emerging trends, discuss the associated limitations, and outline future directions of the field. Impact statement Recent years have seen an increasing drive to construct cell mimics and use them as simplified experimental models to replicate and understand biological phenomena in a well-defined and controlled system. By summarizing the advances in this burgeoning field, and using case studies as a basis for discussion on the limitations and future directions of this approach, it is hoped that this minireview will spur others in the experimental biology community to use artificial cells as simplified models with which to probe biological systems.

  13. Simplified design rule for ratcheting analysis

    International Nuclear Information System (INIS)

    Cousseran, P.; Clement, G.; Lebey, J.; Roche, R.L.

    1982-07-01

    Ratcheting in the creep range is the magnification of primary stress effects caused by cyclic straining. Computation results do not agree with experimental results due to the complexity of the real material behavior. From the results of experimental tests a design rule based on the concept of effective primary stress Psub(eff) is proposed. The effective primary stress is a fictitious primary stress giving the same effect that the real loading i.e. the same effect that the combination of an applied primary stress P and a cyclic straining quoted by the range Qsub(R) of secondary stress variation. Determination of an upper bound value of Psub(eff) is made with the help of an efficiency diagram. More precisely the efficiency diagram include a curve giving a conservative value of an efficiency index V = P/Psub(eff) as a function of the secondarity quotient SQ = Qsub(R)/P. Finally limitation of Psub(eff) intensity is discussed in regard with the current practice

  14. Screening efficacy of a simplified logMAR chart

    Directory of Open Access Journals (Sweden)

    Naganathan Muthuramalingam

    2016-04-01

    Aim: This study evaluates the efficacy of a simplified logMAR chart, designed for VA testing over the conventional Snellen chart, in a school-based vision-screening programme. Methods: We designed a simplified logMAR chart by employing the principles of the Early Treatment Diabetic Retinopathy Study (ETDRS chart in terms of logarithmic letter size progression, inter-letter spacing, and inter-line spacing. Once the simplified logMAR chart was validated by students in the Elite school vision-screening programme, we set out to test the chart in 88 primary and middle schools in the Tiruporur block of Kancheepuram district in Tamil Nadu. One school teacher in each school was trained to screen a cross-sectional population of 10 354 primary and secondary school children (girls: 5488; boys: 4866 for VA deficits using a new, simplified logMAR algorithm. An experienced paediatric optometrist was recruited to validate the screening methods and technique used by the teachers to collect the data. Results: The optometrist screened a subset of 1300 school children from the total sample. The optometrist provided the professional insights needed to validate the clinical efficacy of the simplified logMAR algorithm and verified the reliability of the data collected by the teachers. The mean age of children sampled for validation was 8.6 years (range: 9–14 years. The sensitivity and the specificity of the simplified logMAR chart when compared to the standard logMAR chart were found to be 95% and 98%, respectively. Kappa value was 0.97. Sensitivity of the teachers’ screening was 66.63% (95% confidence interval [CI]: 52.73–77.02 and the specificity was 98.33% (95% CI: 97.49–98.95. Testing of VA was done under substandard illumination levels in 87% of the population. A total of 10 354 children were screened, 425 of whom were found to have some form of visual and/or ocular defect that was identified by the teacher or optometrist. Conclusion: The simplified logMAR testing algorithm

  15. Simplified prognostic model for critically ill patients in resource limited settings in South Asia

    NARCIS (Netherlands)

    Haniffa, Rashan; Mukaka, Mavuto; Munasinghe, Sithum Bandara; de Silva, Ambepitiyawaduge Pubudu; Jayasinghe, Kosala Saroj Amarasiri; Beane, Abi; de Keizer, Nicolette; Dondorp, Arjen M.

    2017-01-01

    Background: Current critical care prognostic models are predominantly developed in high-income countries (HICs) and may not be feasible in intensive care units (ICUs) in lower-and middle-income countries (LMICs). Existing prognostic models cannot be applied without validation in LMICs as the

  16. S-Channel Dark Matter Simplified Models and Unitarity

    CERN Document Server

    Englert, Christoph; Spannowsky, Michael

    The ultraviolet structure of $s$-channel mediator dark matter simplified models at hadron colliders is considered. In terms of commonly studied $s$-channel mediator simplified models it is argued that at arbitrarily high energies the perturbative description of dark matter production in high energy scattering at hadron colliders will break down in a number of cases. This is analogous to the well documented breakdown of an EFT description of dark matter collider production. With this in mind, to diagnose whether or not the use of simplified models at the LHC is valid, perturbative unitarity of the scattering amplitude in the processes relevant to LHC dark matter searches is studied. The results are as one would expect: at the LHC and future proton colliders the simplified model descriptions of dark matter production are in general valid. As a result of the general discussion, a simple new class of previously unconsidered `Fermiophobic Scalar' simplified models is proposed, in which a scalar mediator couples to...

  17. Indirect detection constraints on s- and t-channel simplified models of dark matter

    Science.gov (United States)

    Carpenter, Linda M.; Colburn, Russell; Goodman, Jessica; Linden, Tim

    2016-09-01

    Recent Fermi-LAT observations of dwarf spheroidal galaxies in the Milky Way have placed strong limits on the gamma-ray flux from dark matter annihilation. In order to produce the strongest limit on the dark matter annihilation cross section, the observations of each dwarf galaxy have typically been "stacked" in a joint-likelihood analysis, utilizing optical observations to constrain the dark matter density profile in each dwarf. These limits have typically been computed only for singular annihilation final states, such as b b ¯ or τ+τ- . In this paper, we generalize this approach by producing an independent joint-likelihood analysis to set constraints on models where the dark matter particle annihilates to multiple final-state fermions. We interpret these results in the context of the most popular simplified models, including those with s- and t-channel dark matter annihilation through scalar and vector mediators. We present our results as constraints on the minimum dark matter mass and the mediator sector parameters. Additionally, we compare our simplified model results to those of effective field theory contact interactions in the high-mass limit.

  18. Non-simplified SUSY. {tau}-coannihilation at LHC and ILC

    Energy Technology Data Exchange (ETDEWEB)

    Berggren, M.; Cakir, A.; Krueger, D.; List, J.; Lobanov, A.; Melzer-Pellmann, I.A.

    2013-07-15

    Simplified models have become a widely used and important tool to cover the more diverse phenomenology beyond constrained SUSY models. However, they come with a substantial number of caveats themselves, and great care needs to be taken when drawing conclusions from limits based on the simplified approach. To illustrate this issue with a concrete example, we examine the applicability of simplified model results to a series of full SUSY model points which all feature a small {tau} -LSP mass difference, and are compatible with electroweak and flavor precision observables as well as current LHC results. Various channels have been studied using the Snowmass Combined LHC detector implementation in the Delphes simulation package, as well as the Letter of Intent or Technical Design Report simulations of the ILD detector concept at the ILC. We investigated both the LHC and ILC capabilities for discovery, separation and identification of all parts of the spectrum. While parts of the spectrum would be discovered at the LHC, there is substantial room for further discoveries and property determination at the ILC.

  19. Towards the next generation of simplified Dark Matter models

    CERN Document Server

    Albert, Andreas

    This White Paper is an input to the ongoing discussion about the extension and refinement of simplified Dark Matter (DM) models. Based on two concrete examples, we show how existing simplified DM models (SDMM) can be extended to provide a more accurate and comprehensive framework to interpret and characterise collider searches. In the first example we extend the canonical SDMM with a scalar mediator to include mixing with the Higgs boson. We show that this approach not only provides a better description of the underlying kinematic properties that a complete model would possess, but also offers the option of using this more realistic class of scalar mixing models to compare and combine consistently searches based on different experimental signatures. The second example outlines how a new physics signal observed in a visible channel can be connected to DM by extending a simplified model including effective couplings. This discovery scenario uses the recently observed excess in the high-mass diphoton searches of...

  20. Optical chirp z-transform processor with a simplified architecture.

    Science.gov (United States)

    Ngo, Nam Quoc

    2014-12-29

    Using a simplified chirp z-transform (CZT) algorithm based on the discrete-time convolution method, this paper presents the synthesis of a simplified architecture of a reconfigurable optical chirp z-transform (OCZT) processor based on the silica-based planar lightwave circuit (PLC) technology. In the simplified architecture of the reconfigurable OCZT, the required number of optical components is small and there are no waveguide crossings which make fabrication easy. The design of a novel type of optical discrete Fourier transform (ODFT) processor as a special case of the synthesized OCZT is then presented to demonstrate its effectiveness. The designed ODFT can be potentially used as an optical demultiplexer at the receiver of an optical fiber orthogonal frequency division multiplexing (OFDM) transmission system.

  1. Microtensile bond strength of three simplified adhesive systems to caries-affected dentin.

    Science.gov (United States)

    Scholtanus, J D; Purwanta, Kenny; Dogan, Nilgun; Kleverlaan, Cees J; Feilzer, Albert J

    2010-08-01

    The purpose of the study was to determine the microtensile bond strength of three different simplified adhesive systems to caries-affected dentin. Fifteen extracted human molars with primary carious lesions were ground flat until dentin was exposed. Soft caries-infected dentin was excavated with the help of caries detector dye. On the remaining hard dentin, a standardized smear layer was created by polishing with 600-grit SiC paper. Teeth were divided into three groups and treated with one of the three tested adhesives: Adper Scotchbond 1 XT (3M ESPE), a 2-step etch-andrinse adhesive, Clearfil S3 Bond (Kuraray), a 1-step self-etching or all-in-one adhesive, and Clearfil SE Bond (Kuraray), a 2-step self-etching adhesive. Five-mm-thick composite buildups (Z-250, 3M ESPE) were built and light cured. After water storage for 24 h at 37ºC, the bonded specimens were sectioned into bars (1.0 x 1.0 mm; n = 20 to 30). Microtensile bond strength of normal dentin specimens and caries-affected dentin specimens was measured in a universal testing machine (crosshead speed = 1 mm/min). Data were analyzed using two-way ANOVA and Tukey's post-hoc test (p adhesives were found. Adper Scotchbond 1 XT and Clearfil S3 Bond showed significantly lower bond strength values to caries-affected dentin. For Clearfil SE Bond, bond strength values to normal and caries-affected dentin were not significantly different. All the tested simplified adhesives showed similar bond strength values to normal dentin. For the tested 2-step etch-and-rinse adhesive and the all-in-one adhesive, the bond strength values to caries-affected dentin were lower than to normal dentin.

  2. Normalized modes at selected points without normalization

    Science.gov (United States)

    Kausel, Eduardo

    2018-04-01

    As every textbook on linear algebra demonstrates, the eigenvectors for the general eigenvalue problem | K - λM | = 0 involving two real, symmetric, positive definite matrices K , M satisfy some well-defined orthogonality conditions. Equally well-known is the fact that those eigenvectors can be normalized so that their modal mass μ =ϕT Mϕ is unity: it suffices to divide each unscaled mode by the square root of the modal mass. Thus, the normalization is the result of an explicit calculation applied to the modes after they were obtained by some means. However, we show herein that the normalized modes are not merely convenient forms of scaling, but that they are actually intrinsic properties of the pair of matrices K , M, that is, the matrices already "know" about normalization even before the modes have been obtained. This means that we can obtain individual components of the normalized modes directly from the eigenvalue problem, and without needing to obtain either all of the modes or for that matter, any one complete mode. These results are achieved by means of the residue theorem of operational calculus, a finding that is rather remarkable inasmuch as the residues themselves do not make use of any orthogonality conditions or normalization in the first place. It appears that this obscure property connecting the general eigenvalue problem of modal analysis with the residue theorem of operational calculus may have been overlooked up until now, but which has in turn interesting theoretical implications.Á

  3. Revisiting the direct detection of dark matter in simplified models

    OpenAIRE

    Li, Tong

    2018-01-01

    In this work we numerically re-examine the loop-induced WIMP-nucleon scattering cross section for the simplified dark matter models and the constraint set by the latest direct detection experiment. We consider a fermion, scalar or vector dark matter component from five simplified models with leptophobic spin-0 mediators coupled only to Standard Model quarks and dark matter particles. The tree-level WIMP-nucleon cross sections in these models are all momentum-suppressed. We calculate the non-s...

  4. Simplified Chua's attractor via bridging a diode pair

    Directory of Open Access Journals (Sweden)

    Quan Xu

    2015-04-01

    Full Text Available In this paper, a simplified Chua's circuit is realised by bridging a diode pair between a passive LC (inductance and capacitance in parallel connection - LC oscillator and an active RC (resistance and capacitance in parallel connection - RC filter. The dynamical behaviours of the circuit are investigated by numerical simulations and verified by experimental measurements. It is found that the simplified Chua's circuit generates Chua's attractors similarly and demonstrates complex non-linear phenomena including coexisting bifurcation modes and coexisting attractors in particular.

  5. Simple design of slanted grating with simplified modal method.

    Science.gov (United States)

    Li, Shubin; Zhou, Changhe; Cao, Hongchao; Wu, Jun

    2014-02-15

    A simplified modal method (SMM) is presented that offers a clear physical image for subwavelength slanted grating. The diffraction characteristic of the slanted grating under Littrow configuration is revealed by the SMM as an equivalent rectangular grating, which is in good agreement with rigorous coupled-wave analysis. Based on the equivalence, we obtained an effective analytic solution for simplifying the design and optimization of a slanted grating. It offers a new approach for design of the slanted grating, e.g., a 1×2 beam splitter can be easily designed. This method should be helpful for designing various new slanted grating devices.

  6. Effects of simplifying outreach materials for energy conservation programs that target low-income consumers

    International Nuclear Information System (INIS)

    Wong-Parodi, Gabrielle; Bruine de Bruin, Wändi; Canfield, Casey

    2013-01-01

    Critics have speculated that the limited success of energy conservation programs among low-income consumers may partly be due to recipients having insufficient literacy to understand the outreach materials. Indeed, we found outreach materials for low-income consumers to require relatively high levels of reading comprehension. We therefore improved the Flesch–Kincaid readability statistics for two outreach brochures, by using shorter words and shorter sentences to describe their content. We examined the effect of that simplification on low-income consumers′ responses. Participants from low-income communities in the greater Pittsburgh area, who varied in literacy, were randomly assigned to either original communications about energy conservation programs or our simplified versions. Our findings suggest that lowering readability statistics successfully simplified only the more straightforward brochure in our set of two, likely because its content lent itself better to simplification. Findings for this brochure showed that simplification improved understanding of its content among both low-literacy and high-literacy recipients, without adversely affecting their evaluation of the materials, or their intention to enroll in the advertised programs. We discuss strategies for improving communication materials that aim to reach out to low-income populations. - Highlights: • Brochures about energy programs for low-income consumers can be too hard to read. • We made brochures easier to read by using shorter words and shorter sentences. • Simplifying a straightforward brochure improved the understanding of all recipients. • However, simplifying a complex brochure had no effect on understanding. • We suggest strategies for improving outreach to low-income consumers

  7. Charts for specifying limits on copper stabilizer damage rate

    International Nuclear Information System (INIS)

    Sawan, M.E.

    1984-01-01

    Charts that simplify the task of specifying the damage rate limit in the copper stabilizer of fusion reactor superconducting magnets are presented. Partial damage recovery with annealing is accounted for. Applications to the MARS magnets are discussed. (orig.)

  8. Artificial neural network analysis applied to simplifying bioeffect radiotherapy treatment planning

    International Nuclear Information System (INIS)

    Purnomo, A.B.

    2001-01-01

    Full text: A bioeffect planning system has been developed by Wigg and Nicholls in the Departments of Clinical Radiobiology and Medical Physics, at the Royal Adelaide Hospital. The system has been developed to be an experimental tool by means of which bioeffect plans may be compared with conventional isodose plans in radiotherapy. Limitations of isodose planning, in many common clinical circumstances, have been apparent for sometime (Wigg and Wilson, Australasian Radiology, 1981, 25: 205-212). There are many reasons why bioeffect planning has been slow in developing. These include concerns about the clinical application of theoretical radiobiology models, the uncertainty of normal tissue and tumour parameter values, and the non-availability of suitable computer systems capable of performing bioeffect planning. These concerns are fully justified and isodose planning must remain, for the foreseeable future, the gold standard for clinical treatment. However, these concerns must be judged against the certainty that isodose planning, in which the only variable usually considered is the total dose, can be substantially misleading. Unfortunately, a typical Tumour Control Probability (TCP) equation for bioeffect planning is complex with 12 parameters. Consequently, the equation is difficult to implement in practice. Can the equation be simplified by ignoring the variability of some of the parameters? To test this possibility, we have attempted a neural network analysis of the problem. The capability of artificial neural network (ANN) analysis to solve classification problems was explored in which a weight space analysis was conducted. It led to the reduction of the number of parameters. The training data for the ANN analysis was generated using the above equation and practical data from many publications. The performance of the optimized ANN and the reduced-parameter ANN were tested using other treatment data. The optimized ANN results closely matched with those of the

  9. Simplified PET measurement for evaluating histamine H1 receptors in human brains using [11C]doxepin

    International Nuclear Information System (INIS)

    Mochizuki, Hideki; Kimura, Yuichi; Ishii, Kenji; Oda, Keiichi; Sasaki, Toru; Tashiro, Manabu; Yanai, Kazuhiko; Ishiwata, Kiichi

    2004-01-01

    The aim of this study was to develop simplified positron emission tomography measurement using [ 11 C]doxepin ([ 11 C]DOX) to evaluate histamine H 1 receptors (H1Rs) in human brains. We evaluated the correlation between the distribution volume (DV) of [ 11 C]DOX, estimated quantitatively with a two-compartment model, and the [ 11 C]DOX uptake obtained at various time intervals and normalized using the metabolite-corrected plasma radioactivity. We found that the static 70- to 90-min images normalized using the plasma radioactivity at 10 min postinjection reflected the DV of [ 11 C]DOX-H1R binding

  10. An empirical multivariate log-normal distribution representing uncertainty of biokinetic parameters for 137Cs

    International Nuclear Information System (INIS)

    Miller, G.; Martz, H.; Bertelli, L.; Melo, D.

    2008-01-01

    A simplified biokinetic model for 137 Cs has six parameters representing transfer of material to and from various compartments. Using a Bayesian analysis, the joint probability distribution of these six parameters is determined empirically for two cases with quite a lot of bioassay data. The distribution is found to be a multivariate log-normal. Correlations between different parameters are obtained. The method utilises a fairly large number of pre-determined forward biokinetic calculations, whose results are stored in interpolation tables. Four different methods to sample the multidimensional parameter space with a limited number of samples are investigated: random, stratified, Latin Hypercube sampling with a uniform distribution of parameters and importance sampling using a lognormal distribution that approximates the posterior distribution. The importance sampling method gives much smaller sampling uncertainty. No sampling method-dependent differences are perceptible for the uniform distribution methods. (authors)

  11. An OOP Approach to Simplify MDI Application Development An OOP Approach to Simplify MDI Application Development

    Directory of Open Access Journals (Sweden)

    Donato Hernández Fusilier

    2012-02-01

    Full Text Available The Multiple Document Interface (MDI is a Microsoft Windows specification that allows managing multiple documents using a single graphic interface application. An MDI application allows opening several documents simultaneously. Only one document is active at a particular time. MDI applications can be deployed using Win32 or Microsoft Foundation Classes (MFC. Programs developed using Win32 are faster than those using MFC. However, Win32applications are difficult to implement and prone to errors. It should be mentioned that, learning how to properly use MFC to deploy MDI applications is not simple, and performance is typically worse than that of Win32 applications. A method to simplify the development of MDI applications using Object-Oriented Programming (OOP is proposed. Subsequently, it is shown that this method generates compact code that is easier to read and maintain than other methods (i.e., MFC. Finally, it is demonstrated that the proposed method allowsthe rapid development of MDI applications without sacrificing application performance.La Interfase para Múltiples Documentos (MDI es una especificación del sistema operativo Microsoft Windows que permite manipular varios documentos usando un sólo programa. Un programa del tipo MDI permite abrir varios documentos simultáneamente. En un instante dado, sólo un documento es activo. Los programas del tipo MDI pueden desarrollarseu sando Win32 o las clases fundamentales de Microsoft (MFC. Los programas desarrollados usando Win32 son más rápidos que los programas que usan MFC. Sin embargo, éstos son difíciles de implementar promoviendo la existencia de errores. Cabe mencionar que el desarrollo de programas del tipo MDI usando MFC no es sencillo, y que su desempeño estípicamente peor que el de un programa del tipo Win32. Se propone un método que drásticamente simplifica el desarrollo de programas del tipo MDI por medio de la Programación Orientada a Objetos (POO. Se demuestra que el m

  12. Transosseous fixation of pediatric displaced mandibular fractures with polyglactin resorbable suture--a simplified technique.

    Science.gov (United States)

    Chandan, Sanjay; Halli, Rajshekhar; Joshi, Samir; Chhabaria, Gaurav; Setiya, Sneha

    2013-11-01

    Management of pediatric mandibular fractures presents a unique challenge to surgeons in terms of its numerous variations compared to adults. Both conservative and open methods have been advocated with their obvious limitations and complications. However, conservative modalities may not be possible in grossly displaced fractures, which necessitate the open method of fixation. We present a novel and simplified technique of transosseous fixation of displaced pediatric mandibular fractures with polyglactin resorbable suture, which provides adequate stability without any interference with tooth buds and which is easy to master.

  13. Normal foot and ankle

    International Nuclear Information System (INIS)

    Weissman, S.D.

    1989-01-01

    The foot may be thought of as a bag of bones tied tightly together and functioning as a unit. The bones re expected to maintain their alignment without causing symptomatology to the patient. The author discusses a normal radiograph. The bones must have normal shape and normal alignment. The density of the soft tissues should be normal and there should be no fractures, tumors, or foreign bodies

  14. Option valuation with the simplified component GARCH model

    DEFF Research Database (Denmark)

    Dziubinski, Matt P.

    We introduce the Simplified Component GARCH (SC-GARCH) option pricing model, show and discuss sufficient conditions for non-negativity of the conditional variance, apply it to low-frequency and high-frequency financial data, and consider the option valuation, comparing the model performance...

  15. Image-Based Edge Bundles : Simplified Visualization of Large Graphs

    NARCIS (Netherlands)

    Telea, A.; Ersoy, O.

    2010-01-01

    We present a new approach aimed at understanding the structure of connections in edge-bundling layouts. We combine the advantages of edge bundles with a bundle-centric simplified visual representation of a graph's structure. For this, we first compute a hierarchical edge clustering of a given graph

  16. Sensitivity Analysis of a Simplified Fire Dynamic Model

    DEFF Research Database (Denmark)

    Sørensen, Lars Schiøtt; Nielsen, Anker

    2015-01-01

    This paper discusses a method for performing a sensitivity analysis of parameters used in a simplified fire model for temperature estimates in the upper smoke layer during a fire. The results from the sensitivity analysis can be used when individual parameters affecting fire safety are assessed...

  17. Simplified polynomial representation of cross sections for reactor calculation

    International Nuclear Information System (INIS)

    Dias, A.M.; Sakai, M.

    1985-01-01

    It is shown a simplified representation of a cross section library generated by transport theory using the cell model of Wigner-Seitz for typical PWR fuel elements. The effect of burnup evolution through tables of reference cross sections and the effect of the variation of the reactor operation parameters considered by adjusted polynomials are presented. (M.C.K.) [pt

  18. 77 FR 54482 - Allocation of Costs Under the Simplified Methods

    Science.gov (United States)

    2012-09-05

    ... cost of goods sold cash or trade discounts that taxpayers do not capitalize for book purposes (and... to adjust additional section 263A costs for cash or trade discounts described in Sec. 1.471-3(b... Allocation of Costs Under the Simplified Methods AGENCY: Internal Revenue Service (IRS), Treasury. ACTION...

  19. "4 x 4 vasovasostomy": A simplified technique for vasectomy reversal

    Directory of Open Access Journals (Sweden)

    Rajeev Kumar

    2010-01-01

    Conclusions : The "4 × 4" modified two-layer vasovasostomy is a simple technique that can be performed in quick time with excellent results. It may allow a common ground between the complex microdot two-layer technique and the over-simplified single-layer procedure.

  20. 48 CFR 432.003 - Simplified acquisition procedures financing.

    Science.gov (United States)

    2010-10-01

    ... procedures financing. 432.003 Section 432.003 Federal Acquisition Regulations System DEPARTMENT OF AGRICULTURE GENERAL CONTRACTING REQUIREMENTS CONTRACT FINANCING 432.003 Simplified acquisition procedures financing. (a) The chief of the contracting office may approve contract financing on a contract to be...

  1. 48 CFR 1332.003 - Simplified acquisition procedures financing.

    Science.gov (United States)

    2010-10-01

    ... procedures financing. 1332.003 Section 1332.003 Federal Acquisition Regulations System DEPARTMENT OF COMMERCE GENERAL CONTRACTING REQUIREMENTS CONTRACT FINANCING 1332.003 Simplified acquisition procedures financing. Contract financing may be provided for purchases made under the authority of FAR Part 13. Contract...

  2. 48 CFR 1532.003 - Simplified acquisition procedures financing.

    Science.gov (United States)

    2010-10-01

    ... procedures financing. 1532.003 Section 1532.003 Federal Acquisition Regulations System ENVIRONMENTAL PROTECTION AGENCY GENERAL CONTRACTING REQUIREMENTS CONTRACT FINANCING 1532.003 Simplified acquisition procedures financing. (a) Scope. This subpart provides for authorization of advance and interim payments on...

  3. Simplifying the audit of risk factor recording and control

    DEFF Research Database (Denmark)

    Zhao, Min; Cooney, Marie Therese; Klipstein-Grobusch, Kerstin

    2016-01-01

    BACKGROUND: To simplify the assessment of the recording and control of coronary heart disease risk factors in different countries and regions. DESIGN: The SUrvey of Risk Factors (SURF) is an international clinical audit. METHODS: Data on consecutive patients with established coronary heart disease...

  4. A Simplified Technique for Evaluating Human "CCR5" Genetic Polymorphism

    Science.gov (United States)

    Falteisek, Lukáš; Cerný, Jan; Janštová, Vanda

    2013-01-01

    To involve students in thinking about the problem of AIDS (which is important in the view of nondecreasing infection rates), we established a practical lab using a simplified adaptation of Thomas's (2004) method to determine the polymorphism of HIV co-receptor CCR5 from students' own epithelial cells. CCR5 is a receptor involved in inflammatory…

  5. On the sustainability area as a simplifying didactic device

    DEFF Research Database (Denmark)

    Harck, Søren H.

    2000-01-01

    Recently, the sustainability area of public finance has been launched as a simplifying screening device for the analysis of fiscal sustainability. In this paper it is argued that the novel notion of the sustainability area (reflecting, in turn, a simple notion of public debt sustainability) does ...

  6. Simplified polynomial digital predistortion for multimode software defined radios

    DEFF Research Database (Denmark)

    Kardaras, Georgios; Soler, José; Dittmann, Lars

    2010-01-01

    a simplified approach using polynomial digital predistortion in the intermediated frequency (IF) domain. It is fully implementable in software and no hardware changes are required on the digital or analog platform. The adaptation algorithm selected was Least Mean Squares because of its relevant simplicity...

  7. Improved cosine similarity measures of simplified neutrosophic setsfor medical diagnoses

    OpenAIRE

    Jun Ye

    2014-01-01

    In pattern recognition and medical diagnosis, similarity measure is an important mathematicaltool. To overcome some disadvantages of existing cosine similarity measures of simplified neutrosophicsets (SNSs) in vector space, this paper proposed improved cosine similarity measures of SNSs based oncosine function, including single valued neutrosophic cosine similarity measures and interval neutro-sophic cosine similarity measures. Then, weighted cosine similarity measures of SNSs were introduced...

  8. Simplified method for beatlength measurement in optical fibre

    International Nuclear Information System (INIS)

    Chu, R.; Town, G.

    2000-01-01

    Full text: A simplified technique for measuring beatlength in birefringent optical fibres using magnetic modulation was analysed, and tested experimentally. By avoiding the use of unnecessary optical components and splicing to the fibre under test, the beatlength was measured accurately with good signal-to-noise ratio

  9. Application of simplified PC-SAFT to glycol ethers

    DEFF Research Database (Denmark)

    Avlund, Ane Søgaard; Kontogeorgis, Georgios; Michelsen, Michael Locht

    2012-01-01

    The simplified PC-SAFT (sPC-SAFT) equation of state is applied for binary glycol ether-containing mixtures, and it is investigated how the results are influenced by inclusion of intramolecular association in the association theory. Three different glycol ethers are examined: 2-methoxyethanol, 2...

  10. Validation of the Simplified Motor Score in patients with traumatic ...

    African Journals Online (AJOL)

    Background. This study used data from a large prospectively entered database to assess the efficacy of the motor score (M score) component of the Glasgow Coma Scale (GCS) and the Simplified Motor Score (SMS) in predicting overall outcome in patients with traumatic brain injury (TBI). Objective. To safely and reliably ...

  11. Simplified percutaneous large bore suprapubic cystostomy for acute ...

    African Journals Online (AJOL)

    C.O. Okorie

    Abstract. Introduction and objectives: Commercial cystostomy kits/trocars are not always readily available in regions with insufficient funding. Open suprapubic cystostomy procedures are yet prevalent. This paper presents a simplified percutaneous suprapubic cystostomy technique that utilizes specially selected surgical ...

  12. Delayed ripple counter simplifies square-root computation

    Science.gov (United States)

    Cliff, R.

    1965-01-01

    Ripple subtract technique simplifies the logic circuitry required in a binary computing device to derive the square root of a number. Successively higher numbers are subtracted from a register containing the number out of which the square root is to be extracted. The last number subtracted will be the closest integer to the square root of the number.

  13. A simplified presentation of the multigroup analytic nodal method in 2-D Cartesian geometry

    International Nuclear Information System (INIS)

    Hebert, Alain

    2008-01-01

    The nodal diffusion algorithms used in many production reactor simulation codes are originating from a common ancestry developed in the 1970s, the analytic nodal method (ANM) of the QUANDRY code. However, this original presentation of the ANM is complex and makes difficult the calculation of the nodal coupling matrices. Moreover, QUANDRY is limited to two-energy groups and its generalization to more groups appears laborious. We are presenting a simplified implementation of the ANM requiring only limited programming work. This formulation is consistent with the initial QUANDRY implementation and is easily generalizable to arbitrary G-group problems. A Matlab script is provided to highlight the simplicity of our presentation. For the sake of clarity, our implementation is limited to G-group, 2-D Cartesian geometry

  14. Marrow transfusions into normal recipients

    International Nuclear Information System (INIS)

    Brecher, G.

    1983-01-01

    During the past several years we have explored the transfusion of bone marrow into normal nonirradiated mice. While transfused marrow proliferates readily in irradiated animals, only minimal proliferation takes place in nonirradiated recipients. It has generally been assumed that this was due to the lack of available proliferative sites in recipients with normal marrow. Last year we were able to report that the transfusion of 200 million bone marrow cells (about 2/3 of the total complement of marrow cells of a normal mouse) resulted in 20% to 25% of the recipient's marrow being replaced by donor marrow. Thus we can now study the behavior of animals that have been transfused (donor) and endogenous (recipient) marrow cells, although none of the tissues of either donor or recipient have been irradiated. With these animals we hope to investigate the nature of the peculiar phenomenon of serial exhaustion of marrow, also referred to as the limited self-replicability of stem cells

  15. Superconducting versus normal conducting cavities

    CERN Document Server

    Podlech, Holger

    2013-01-01

    One of the most important issues of high-power hadron linacs is the choice of technology with respect to superconducting or room-temperature operation. The favour for a specific technology depends on several parameters such as the beam energy, beam current, beam power and duty factor. This contribution gives an overview of the comparison between superconducting and normal conducting cavities. This includes basic radiofrequency (RF) parameters, design criteria, limitations, required RF and plug power as well as case studies.

  16. Development and validation of a simplified titration method for monitoring volatile fatty acids in anaerobic digestion.

    Science.gov (United States)

    Sun, Hao; Guo, Jianbin; Wu, Shubiao; Liu, Fang; Dong, Renjie

    2017-09-01

    The volatile fatty acids (VFAs) concentration has been considered as one of the most sensitive process performance indicators in anaerobic digestion (AD) process. However, the accurate determination of VFAs concentration in AD processes normally requires advanced equipment and complex pretreatment procedures. A simplified method with fewer sample pretreatment procedures and improved accuracy is greatly needed, particularly for on-site application. This report outlines improvements to the Nordmann method, one of the most popular titrations used for VFA monitoring. The influence of ion and solid interfering subsystems in titrated samples on results accuracy was discussed. The total solid content in titrated samples was the main factor affecting accuracy in VFA monitoring. Moreover, a high linear correlation was established between the total solids contents and VFA measurement differences between the traditional Nordmann equation and gas chromatography (GC). Accordingly, a simplified titration method was developed and validated using a semi-continuous experiment of chicken manure anaerobic digestion with various organic loading rates. The good fitting of the results obtained by this method in comparison with GC results strongly supported the potential application of this method to VFA monitoring. Copyright © 2017. Published by Elsevier Ltd.

  17. A Combined Gravity Compensation Method for INS Using the Simplified Gravity Model and Gravity Database.

    Science.gov (United States)

    Zhou, Xiao; Yang, Gongliu; Wang, Jing; Wen, Zeyang

    2018-05-14

    In recent decades, gravity compensation has become an important way to reduce the position error of an inertial navigation system (INS), especially for a high-precision INS, because of the extensive application of high precision inertial sensors (accelerometers and gyros). This paper first deducts the INS's solution error considering gravity disturbance and simulates the results. Meanwhile, this paper proposes a combined gravity compensation method using a simplified gravity model and gravity database. This new combined method consists of two steps all together. Step 1 subtracts the normal gravity using a simplified gravity model. Step 2 first obtains the gravity disturbance on the trajectory of the carrier with the help of ELM training based on the measured gravity data (provided by Institute of Geodesy and Geophysics; Chinese Academy of sciences), and then compensates it into the error equations of the INS, considering the gravity disturbance, to further improve the navigation accuracy. The effectiveness and feasibility of this new gravity compensation method for the INS are verified through vehicle tests in two different regions; one is in flat terrain with mild gravity variation and the other is in complex terrain with fierce gravity variation. During 2 h vehicle tests, the positioning accuracy of two tests can improve by 20% and 38% respectively, after the gravity is compensated by the proposed method.

  18. Simplified two-fluid current–voltage relation for superconductor transition-edge sensors

    International Nuclear Information System (INIS)

    Wang, Tian-Shun; Chen, Jun-Kang; Zhang, Qing-Ya; Li, Tie-Fu; Liu, Jian-She; Chen, Wei; Zhou, Xingxiang

    2013-01-01

    We propose a simplified current–voltage (IV) relation for the analysis and simulation of superconductor transition-edge sensor (TES) circuits. Compared to the conventional approach based on the effective TES resistance, our expression describes the device behavior more thoroughly covering the superconducting, transitional, and normal-state for TES currents in both directions. We show how to use our IV relation to perform small-signal analysis and derive the device's temperature and current sensitivities based on its physical parameters. We further demonstrate that we can use our IV relation to greatly simplify TES device modeling and make SPICE simulation of TES circuits easily accessible. We present some interesting results as examples of valuable simulations enabled by our IV relation. -- Highlights: •We propose an IV relation for superconductor transition-edge sensors (TES). •We derive the dependence of the sensitivity of TES on its physical parameters. •We use our IV relation for SPICE modeling of TES device. •We present simulation results using device model based on our IV relation

  19. Simplified two-fluid current–voltage relation for superconductor transition-edge sensors

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Tian-Shun; Chen, Jun-Kang [Department of Optics and Optical Engineering, University of Science and Technology of China, Hefei City, Anhui Province 230026 (China); Zhang, Qing-Ya; Li, Tie-Fu; Liu, Jian-She [Institute of Microelectronics, Tsinghua University, Beijing 100084 (China); Chen, Wei, E-mail: weichen@tsinghua.edu.cn [Institute of Microelectronics, Tsinghua University, Beijing 100084 (China); Zhou, Xingxiang, E-mail: xizhou@ustc.edu.cn [Department of Optics and Optical Engineering, University of Science and Technology of China, Hefei City, Anhui Province 230026 (China)

    2013-11-21

    We propose a simplified current–voltage (IV) relation for the analysis and simulation of superconductor transition-edge sensor (TES) circuits. Compared to the conventional approach based on the effective TES resistance, our expression describes the device behavior more thoroughly covering the superconducting, transitional, and normal-state for TES currents in both directions. We show how to use our IV relation to perform small-signal analysis and derive the device's temperature and current sensitivities based on its physical parameters. We further demonstrate that we can use our IV relation to greatly simplify TES device modeling and make SPICE simulation of TES circuits easily accessible. We present some interesting results as examples of valuable simulations enabled by our IV relation. -- Highlights: •We propose an IV relation for superconductor transition-edge sensors (TES). •We derive the dependence of the sensitivity of TES on its physical parameters. •We use our IV relation for SPICE modeling of TES device. •We present simulation results using device model based on our IV relation.

  20. Development of a simplified methodology for the isotopic determination of fuel spent in Light Water Reactors

    International Nuclear Information System (INIS)

    Hernandez N, H.; Francois L, J.L.

    2005-01-01

    The present work presents a simplified methodology to quantify the isotopic content of the spent fuel of light water reactors; their application is it specific to the Laguna Verde Nucleo electric Central by means of a balance cycle of 18 months. The methodology is divided in two parts: the first one consists on the development of a model of a simplified cell, for the isotopic quantification of the irradiated fuel. With this model the burnt one is simulated 48,000 MWD/TU of the fuel in the core of the reactor, taking like base one fuel assemble type 10x10 and using a two-dimensional simulator for a fuel cell of a light water reactor (CPM-3). The second part of the methodology is based on the creation from an isotopic decay model through an algorithm in C++ (decay) to evaluate the amount, by decay of the radionuclides, after having been irradiated the fuel until the time in which the reprocessing is made. Finally the method used for the quantification of the kilograms of uranium and obtained plutonium of a normalized quantity (1000 kg) of fuel irradiated in a reactor is presented. These results will allow later on to make analysis of the final disposition of the irradiated fuel. (Author)

  1. Clinical assessment of early language development: a simplified short form of the Mandarin communicative development inventory.

    Science.gov (United States)

    Soli, Sigfrid D; Zheng, Yun; Meng, Zhaoli; Li, Gang

    2012-09-01

    The purpose of this study was to develop a practical mean for clinical evaluation of early pediatric language development by establishing developmental trajectories for receptive and expressive vocabulary growth in children between 6 and 32 months of age using a simple, time-efficient assessment tool. Simplified short form versions of the Words and Gestures and Words and Sentences vocabulary inventories in the Mandarin Communicative Development Inventory [1] were developed and used to assess early language development in developmentally normal children from 6 to 32 months of age during routine health checks. Developmental trajectories characterizing the rate of receptive and expressive vocabulary growth between 6 and 32 months of age are reported. These trajectories allow the equivalent age corresponding to a score to be determined after a brief structured interview with the child's parents that can be conducted in a busy clinical setting. The simplified short forms of the Mandarin Communicative Development Inventories can serve as a clinically useful tool to assess early child language development, providing a practical mean of objectively assessing early language development following early interventions to treat young children with hearing impairment as well as speech and language delays. Objective evidence of language development is essential for achievement of effective (re)habilitation outcomes. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  2. Simplified probabilistic approach to determine safety factors in deterministic flaw acceptance criteria

    International Nuclear Information System (INIS)

    Barthelet, B.; Ardillon, E.

    1997-01-01

    The flaw acceptance rules in nuclear components rely on deterministic criteria supposed to ensure the safe operating of plants. The interest of having a reliable method of evaluating the safety margins and the integrity of components led Electricite de France to launch a study to link safety factors with requested reliability. A simplified analytical probabilistic approach is developed to analyse the failure risk in Fracture Mechanics. Assuming lognormal distributions of the main random variables, it is possible considering a simple Linear Elastic Fracture Mechanics model, to determine the failure probability as a function of mean values and logarithmic standard deviations. The 'design' failure point can be analytically calculated. Partial safety factors on the main variables (stress, crack size, material toughness) are obtained in relation with reliability target values. The approach is generalized to elastic plastic Fracture Mechanics (piping) by fitting J as a power law function of stress, crack size and yield strength. The simplified approach is validated by detailed probabilistic computations with PROBAN computer program. Assuming reasonable coefficients of variations (logarithmic standard deviations), the method helps to calibrate safety factors for different components taking into account reliability target values in normal, emergency and faulted conditions. Statistical data for the mechanical properties of the main basic materials complement the study. The work involves laboratory results and manufacture data. The results of this study are discussed within a working group of the French in service inspection code RSE-M. (authors)

  3. Sonographic assessment of the normal limits of the spleen in ...

    African Journals Online (AJOL)

    2013-12-14

    Dec 14, 2013 ... established with a regression model for predicting the splenic sizes. Key words: Children ... either localized or systemic, involving that organ for screening, diagnostic and prognostic purposes. .... variables. The splenic length ...

  4. Simplified slow anti-coincidence circuit for Compton suppression systems

    International Nuclear Information System (INIS)

    Al-Azmi, Darwish

    2008-01-01

    Slow coincidence circuits for the anti-coincidence measurements have been considered for use in Compton suppression technique. The simplified version of the slow circuit has been found to be fast enough, satisfactory and allows an easy system setup, particularly with the advantage of the automatic threshold setting of the low-level discrimination. A well-type NaI detector as the main detector surrounded by plastic guard detector has been arranged to investigate the performance of the Compton suppression spectrometer using the simplified slow circuit. The system has been tested to observe the improvement in the energy spectra for medium to high-energy gamma-ray photons from terrestrial and environmental samples

  5. Simplified Interface to Complex Memory Hierarchies 1.x

    Energy Technology Data Exchange (ETDEWEB)

    2017-02-21

    Memory systems are expected to get evermore complicated in the coming years, and it isn't clear exactly what form that complexity will take. On the software side, a simple, flexible way of identifying and working with memory pools is needed. Additionally, most developers seek code portability and do not want to learn the intricacies of complex memory. Hence, we believe that a library for interacting with complex memory systems should expose two kinds of abstraction: First, a low-level, mechanism-based interface designed for the runtime or advanced user that wants complete control, with its focus on simplified representation but with all decisions left to the caller. Second, a high-level, policy-based interface designed for ease of use for the application developer, in which we aim for best-practice decisions based on application intent. We have developed such a library, called SICM: Simplified Interface to Complex Memory.

  6. Simplified Model and Response Analysis for Crankshaft of Air Compressor

    Science.gov (United States)

    Chao-bo, Li; Jing-jun, Lou; Zhen-hai, Zhang

    2017-11-01

    The original model of crankshaft is simplified to the appropriateness to balance the calculation precision and calculation speed, and then the finite element method is used to analyse the vibration response of the structure. In order to study the simplification and stress concentration for crankshaft of air compressor, this paper compares calculative mode frequency and experimental mode frequency of the air compressor crankshaft before and after the simplification, the vibration response of reference point constraint conditions is calculated by using the simplified model, and the stress distribution of the original model is calculated. The results show that the error between calculative mode frequency and experimental mode frequency is controlled in less than 7%, the constraint will change the model density of the system, the position between the crank arm and the shaft appeared stress concentration, so the part of the crankshaft should be treated in the process of manufacture.

  7. Simplified shielding calculation system for high-intensity proton accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Masumura, Tomomi; Nakashima, Hiroshi; Nakane, Yoshihiro; Sasamoto, Nobuo [Center for Neutron Science, Tokai Research Establishment, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan)

    2000-06-01

    A simplified shielding calculation system is developed for applying conceptual shielding design of facilities in the joint project for high-intensity proton accelerators. The system is composed of neutron transmission calculation part for bulk shielding using simplified formulas: Moyer model and Tesch's formula, and neutron skyshine calculation part using an empirical formula: Stapleton's formula. The system is made with the Microsoft Excel software for user's convenience. This report provides a manual for the system as well as calculation conditions used in the calculation such as Moyer model's parameters. In this report preliminary results based on data at December 8, 1999, are also shown as an example. (author)

  8. Simplified approach to dynamic process modelling. Annex 4

    International Nuclear Information System (INIS)

    Danilytchev, A.; Elistratov, D.; Stogov, V.

    2010-01-01

    This document presents the OKBM contribution to the analysis of a benchmark of BN-600 reactor hybrid core with simultaneous loading of uranium fuel and MOX within the framework of the international IAEA Co-ordinated Research Project 'Updated Codes and Methods to Reduce the Calculational Uncertainties of the LMFR Reactivity Effects'. In accordance with Action 12 defined during the second RCM, the simplified transient analysis was carried out on the basis of the reactivity coefficients sets, presented by all CRP participants. Purpose of present comparison is the evaluation of spread in the basic transient parameters in connection with spread in the used reactivity coefficients. A ULOF accident initial stage on the simplified model was calculated by using the SAS4A code

  9. Working Mechanism for Flexible Perovskite Solar Cells with Simplified Architecture.

    Science.gov (United States)

    Xu, Xiaobao; Chen, Qi; Hong, Ziruo; Zhou, Huanping; Liu, Zonghao; Chang, Wei-Hsuan; Sun, Pengyu; Chen, Huajun; De Marco, Nicholas; Wang, Mingkui; Yang, Yang

    2015-10-14

    In this communication, we report an efficient and flexible perovskite solar cell based on formamidinium lead trihalide (FAPbI3) with simplified configuration. The device achieved a champion efficiency of 12.70%, utilizing direct contact between metallic indium tin oxide (ITO) electrode and perovskite absorber. The underlying working mechanism is proposed subsequently, via a systematic investigation focusing on the heterojunction within this device. A significant charge storage has been observed in the perovskite, which is believed to generate photovoltage and serves as the driving force for charge transferring from the absorber to ITO electrode as well. More importantly, this simplified device structure on flexible substrates suggests its compatibility for scale-up fabrication, which paves the way for commercialization of perovskite photovoltaic technology.

  10. Simplified local density model for adsorption over large pressure ranges

    International Nuclear Information System (INIS)

    Rangarajan, B.; Lira, C.T.; Subramanian, R.

    1995-01-01

    Physical adsorption of high-pressure fluids onto solids is of interest in the transportation and storage of fuel and radioactive gases; the separation and purification of lower hydrocarbons; solid-phase extractions; adsorbent regenerations using supercritical fluids; supercritical fluid chromatography; and critical point drying. A mean-field model is developed that superimposes the fluid-solid potential on a fluid equation of state to predict adsorption on a flat wall from vapor, liquid, and supercritical phases. A van der Waals-type equation of state is used to represent the fluid phase, and is simplified with a local density approximation for calculating the configurational energy of the inhomogeneous fluid. The simplified local density approximation makes the model tractable for routine calculations over wide pressure ranges. The model is capable of prediction of Type 2 and 3 subcritical isotherms for adsorption on a flat wall, and shows the characteristic cusplike behavior and crossovers seen experimentally near the fluid critical point

  11. Representing solute transport through the multi-barrier disposal system by simplified concepts

    International Nuclear Information System (INIS)

    Poteri, A.; Nordman, H.; Pulkkanen, V-M.; Kekaelaeinen, P.; Hautojaervi, A.

    2012-02-01

    The repository system chosen in Finland for spent nuclear fuel is composed of multiple successive transport barriers. If a waste canister is leaking, this multi-barrier system retards and limits the release rates of radionuclides into the biosphere. Analysis of radionuclide migration in the previous performance assessments has largely been based on numerical modelling of the repository system. The simplified analytical approach introduced here provides a tool to analyse the performance of the whole system using simplified representations of the individual transport barriers. This approach is based on the main characteristics of the individual barriers and on the generic nature of the coupling between successive barriers. In the case of underground repository the mass transfer between successive transport barriers is strongly restricted by the interfaces between barriers leading to well-mixed conditions in these barriers. The approach here simplifies the barrier system so that it can be described with a very simple compartment model, where each barrier is represented by a single, or in the case of buffer, by not more than two compartments. This system of compartments could be solved in analogy with a radioactive decay chain. The model of well mixed compartments lends itself to a very descriptive way to represent and analyse the barrier system because the relative efficiency of the different barriers in hindering transport of solutes can be parameterised by the solutes half-times in the corresponding compartments. In a real repository system there will also be a delay between the start of the inflow and the start of the outflow from the barrier. This delay can be important for the release rates of the short lived and sorbing radionuclides, and it was also included in the simplified representation of the barrier system. In a geological multi-barrier system, spreading of the outflowing release pulse is often governed by the typical behaviour of one transport barrier

  12. Representing solute transport through the multi-barrier disposal system by simplified concepts

    Energy Technology Data Exchange (ETDEWEB)

    Poteri, A.; Nordman, H.; Pulkkanen, V-M. [VTT Technical Research Centre of Finland, Espoo (Finland); Kekaelaeinen, P. [Jyvaeskylae Univ. (Finland). Dept. pf Physics; Hautojaervi, A.

    2012-02-15

    The repository system chosen in Finland for spent nuclear fuel is composed of multiple successive transport barriers. If a waste canister is leaking, this multi-barrier system retards and limits the release rates of radionuclides into the biosphere. Analysis of radionuclide migration in the previous performance assessments has largely been based on numerical modelling of the repository system. The simplified analytical approach introduced here provides a tool to analyse the performance of the whole system using simplified representations of the individual transport barriers. This approach is based on the main characteristics of the individual barriers and on the generic nature of the coupling between successive barriers. In the case of underground repository the mass transfer between successive transport barriers is strongly restricted by the interfaces between barriers leading to well-mixed conditions in these barriers. The approach here simplifies the barrier system so that it can be described with a very simple compartment model, where each barrier is represented by a single, or in the case of buffer, by not more than two compartments. This system of compartments could be solved in analogy with a radioactive decay chain. The model of well mixed compartments lends itself to a very descriptive way to represent and analyse the barrier system because the relative efficiency of the different barriers in hindering transport of solutes can be parameterised by the solutes half-times in the corresponding compartments. In a real repository system there will also be a delay between the start of the inflow and the start of the outflow from the barrier. This delay can be important for the release rates of the short lived and sorbing radionuclides, and it was also included in the simplified representation of the barrier system. In a geological multi-barrier system, spreading of the outflowing release pulse is often governed by the typical behaviour of one transport barrier

  13. First births with a simplified culture system for clinical IVF and embryo transfer.

    Science.gov (United States)

    Van Blerkom, Jonathan; Ombelet, Willem; Klerkx, Elke; Janssen, Mia; Dhont, Nathalie; Nargund, Geeta; Campo, Rudi

    2014-03-01

    This study reports the outcome results from a pilot clinical trial using a simplified laboratory method for human IVF. This system reproducibly generates de novo the atmospheric and culture conditions that support normal fertilization and preimplantation embryogenesis to the hatched blastocyst stage without the need for specialized medical-grade gases or equipment. Development from insemination to the hatched blastocyst stage occurs undisturbed in a completely closed system that enables timed performance assessments for embryo selection in situ that, in this study, involved single-embryo transfers on day 3. With the simplified culture system, 8/23 embryos implanted, one miscarried at 8weeks of gestation and seven healthy babies have been born. The methodology and results are discussed with regard to how this simplified system can be adopted worldwide to meet the growing need for accessible and affordable IVF. A common notion concerning the demographics of infertility is that it is largely a phenomenon associated with developed countries, where infertility treatments are commonplace. In fact, most infertile couples reside in developing/low-resource countries where infertility diagnosis and treatment is nonexistent, inaccessible or unaffordable by the vast majority of young men and women in need. The irony of this situation is that bilateral tubal occlusions, for which IVF was originally indicated and is the most effective treatment, is by far the most common cause of their infertility. We have addressed one aspect of this issue, the IVF laboratory, as part of a wider effort by the Walking Egg Project to design and establish small, dedicated centres in developing countries to provide assisted reproduction technologies that are affordable and accessible to a wider proportion of the population in need. The methods for conventional IVF designed to addresses tubal obstructions are relatively simple and free of complex instrumentation and the highly developed

  14. Simplified nonplanar wafer bonding for heterogeneous device integration

    Science.gov (United States)

    Geske, Jon; Bowers, John E.; Riley, Anton

    2004-07-01

    We demonstrate a simplified nonplanar wafer bonding technique for heterogeneous device integration. The improved technique can be used to laterally integrate dissimilar semiconductor device structures on a lattice-mismatched substrate. Using the technique, two different InP-based vertical-cavity surface-emitting laser active regions have been integrated onto GaAs without compromising the quality of the photoluminescence. Experimental and numerical simulation results are presented.

  15. PSHED: a simplified approach to developing parallel programs

    International Nuclear Information System (INIS)

    Mahajan, S.M.; Ramesh, K.; Rajesh, K.; Somani, A.; Goel, M.

    1992-01-01

    This paper presents a simplified approach in the forms of a tree structured computational model for parallel application programs. An attempt is made to provide a standard user interface to execute programs on BARC Parallel Processing System (BPPS), a scalable distributed memory multiprocessor. The interface package called PSHED provides a basic framework for representing and executing parallel programs on different parallel architectures. The PSHED package incorporates concepts from a broad range of previous research in programming environments and parallel computations. (author). 6 refs

  16. Simplified Clinical Tools and Educational Outreach for Health Workers

    International Development Research Centre (IDRC) Digital Library (Canada)

    Developed in South Africa, simplified tools and training have been shown to improve outcomes for HIV, tuberculosis (TB) and primary care patients, and to enhance staff ... Les conclusions d'un programme financé par le CRDI au premier plan de la conférence annuelle de l'Institut d'étude du développement international de ...

  17. Customs Representation in Simplified Customs Procedures in Republic of Croatia

    Directory of Open Access Journals (Sweden)

    Čedomir Ivaković

    2005-07-01

    Full Text Available When introduced in 2000 the use of authorized consigneeand consignor status was not particularly popular among companies,despite its apparent advantages. The number of the statususers compared to the total number of exporters and importerswas almost negligible. The aim of this paper was to find outto which extent the simplified customs procedures have beenaccepted in Croatia through an objective outline of advantagesand disadvantages that the companies - users of the simplifiedprocedures face on a daily basis.

  18. Towards the next generation of simplified Dark Matter models

    Science.gov (United States)

    Albert, Andreas; Bauer, Martin; Brooke, Jim; Buchmueller, Oliver; Cerdeño, David G.; Citron, Matthew; Davies, Gavin; de Cosa, Annapaola; De Roeck, Albert; De Simone, Andrea; Du Pree, Tristan; Flaecher, Henning; Fairbairn, Malcolm; Ellis, John; Grohsjean, Alexander; Hahn, Kristian; Haisch, Ulrich; Harris, Philip C.; Khoze, Valentin V.; Landsberg, Greg; McCabe, Christopher; Penning, Bjoern; Sanz, Veronica; Schwanenberger, Christian; Scott, Pat; Wardle, Nicholas

    2017-06-01

    This White Paper is an input to the ongoing discussion about the extension and refinement of simplified Dark Matter (DM) models. It is not intended as a comprehensive review of the discussed subjects, but instead summarises ideas and concepts arising from a brainstorming workshop that can be useful when defining the next generation of simplified DM models (SDMM). In this spirit, based on two concrete examples, we show how existing SDMM can be extended to provide a more accurate and comprehensive framework to interpret and characterise collider searches. In the first example we extend the canonical SDMM with a scalar mediator to include mixing with the Higgs boson. We show that this approach not only provides a better description of the underlying kinematic properties that a complete model would possess, but also offers the option of using this more realistic class of scalar mixing models to compare and combine consistently searches based on different experimental signatures. The second example outlines how a new physics signal observed in a visible channel can be connected to DM by extending a simplified model including effective couplings. In the next part of the White Paper we outline other interesting options for SDMM that could be studied in more detail in the future. Finally, we review important aspects of supersymmetric models for DM and use them to propose how to develop more complete SDMMs. This White Paper is a summary of the brainstorming meeting "Next generation of simplified Dark Matter models" that took place at Imperial College, London on May 6, 2016, and corresponding follow-up studies on selected subjects.

  19. Versatile composite resins simplifying the practice of restorative dentistry.

    Science.gov (United States)

    Margeas, Robert

    2014-01-01

    After decades of technical development and refinement, composite resins continue to simplify the practice of restorative dentistry, offering clinicians versatility, predictability, and enhanced physical properties. With a wide range of products available today, composite resins are a reliable, conservative, multi-functional restorative material option. As manufacturers strive to improve such properties as compression strength, flexural strength, elastic modulus, coefficient of thermal expansion, water sorption, and wear resistance, several classification systems of composite resins have been developed.

  20. A simplified model of aerosol removal by containment sprays

    Energy Technology Data Exchange (ETDEWEB)

    Powers, D.A. (Sandia National Labs., Albuquerque, NM (United States)); Burson, S.B. (Nuclear Regulatory Commission, Washington, DC (United States). Div. of Safety Issue Resolution)

    1993-06-01

    Spray systems in nuclear reactor containments are described. The scrubbing of aerosols from containment atmospheres by spray droplets is discussed. Uncertainties are identified in the prediction of spray performance when the sprays are used as a means for decontaminating containment atmospheres. A mechanistic model based on current knowledge of the physical phenomena involved in spray performance is developed. With this model, a quantitative uncertainty analysis of spray performance is conducted using a Monte Carlo method to sample 20 uncertain quantities related to phenomena of spray droplet behavior as well as the initial and boundary conditions expected to be associated with severe reactor accidents. Results of the uncertainty analysis are used to construct simplified expressions for spray decontamination coefficients. Two variables that affect aerosol capture by water droplets are not treated as uncertain; they are (1) [open quote]Q[close quote], spray water flux into the containment, and (2) [open quote]H[close quote], the total fall distance of spray droplets. The choice of values of these variables is left to the user since they are plant and accident specific. Also, they can usually be ascertained with some degree of certainty. The spray decontamination coefficients are found to be sufficiently dependent on the extent of decontamination that the fraction of the initial aerosol remaining in the atmosphere, m[sub f], is explicitly treated in the simplified expressions. The simplified expressions for the spray decontamination coefficient are given. Parametric values for these expressions are found for median, 10 percentile, and 90 percentile values in the uncertainty distribution for the spray decontamination coefficient. Examples are given to illustrate the utility of the simplified expressions to predict spray decontamination of an aerosol-laden atmosphere.

  1. Simplified validation of borderline hits of database searches

    OpenAIRE

    Thomas, Henrik; Shevchenko, Andrej

    2008-01-01

    Along with unequivocal hits produced by matching multiple MS/MS spectra to database sequences, LC-MS/MS analysis often yields a large number of hits of borderline statistical confidence. To simplify their validation, we propose to use rapid de novo interpretation of all acquired MS/MS spectra and, with the help of a simple software tool, display the candidate sequences together with each database search hit. We demonstrate that comparing hit database sequences and independent de novo interpre...

  2. Simplifying the writing process for the novice writer.

    Science.gov (United States)

    Redmond, Mary Connie

    2002-10-01

    Nurses take responsibility for reading information to update their professional knowledge and to meet relicensure requirements. However, nurses are less enthusiastic about writing for professional publication. This article explores the reluctance of nurses to write, the reasons why writing for publication is important to the nursing profession, the importance of mentoring to potential writers, and basic information about simplifying the writing process for novice writers. Copyright 2002 by American Society of PeriAnesthesia Nurses.

  3. Expanding the net: The re-evaluation of the multidimensional nomogram calculating the upper limit of normal PTH (maxPTH) in the setting of secondary hyperparathyroidism and the development of the MultIdimensional Predictive hyperparaTHyroid model (Mi-PTH).

    Science.gov (United States)

    Rajhbeharrysingh, Uma; El Youssef, Joseph; Leon, Enrique; Lasarev, Michael R; Klein, Robert; Vanek, Chaim; Mattar, Samer; Berber, Eren; Siperstein, Allan; Shindo, Maisie; Milas, Mira

    2016-01-01

    The multidimensional nomogram calculating the upper limit of normal PTH (maxPTH) model identifies a personalized upper limit of normal parathyroid hormone (PTH) and successfully predicts classical primary hyperparathyroidism (PHP). We aimed to assess whether maxPTH can distinguish normocalcemic PHP (NCPHP) from secondary hyperparathyroidism (SHP), including subjects who underwent bariatric surgery (BrS). A total of 172 subjects with 359 complete datasets of serum calcium (Ca), 25-OH vitamin D, and intact PTH from Oregon were analyzed: 123 subjects (212 datasets) with PHP and 47 (143) with SHP, including 28 (100) with previous BrS. An improved prediction model, MultIdimensional evaluation for Primary hyperparaTHyroidism (Mi-PTH), was created with the same variables as maxPTH by the use of a combined cohort (995 subjects) including participants from previous studies. In the Oregon cohort, maxPTH's sensitivity was 100% for classical PHP and 89% for NCPHP, but only 50% for normohormonal PHP (NHPHP) and 40% specific for SHP. In comparison, although sensitivity for NCPHP was similar (89%), Mi-PTH vastly improved SHP specificity (85%). In the combined cohort, Mi-PTH had better sensitivity of 98.5% (vs 95%) and specificity 97% (vs 85%). MaxPTH was sensitive in detecting PHP; however, there was low specificity for SHP, especially in patients who underwent BrS. The creation of Mi-PTH provided improved performance measures but requires further prospective evaluation. Copyright © 2016 Elsevier Inc. All rights reserved.

  4. Influencing Factors and Simplified Model of Film Hole Irrigation

    Directory of Open Access Journals (Sweden)

    Yi-Bo Li

    2017-07-01

    Full Text Available Film hole irrigation is an advanced low-cost and high-efficiency irrigation method, which can improve water conservation and water use efficiency. Given its various advantages and potential applications, we conducted a laboratory study to investigate the effects of soil texture, bulk density, initial soil moisture, irrigation depth, opening ratio (ρ, film hole diameter (D, and spacing on cumulative infiltration using SWMS-2D. We then proposed a simplified model based on the Kostiakov model for infiltration estimation. Error analyses indicated SWMS-2D to be suitable for infiltration simulation of film hole irrigation. Additional SWMS-2D-based investigations indicated that, for a certain soil, initial soil moisture and irrigation depth had the weakest effects on cumulative infiltration, whereas ρ and D had the strongest effects on cumulative infiltration. A simplified model with ρ and D was further established, and its use was then expanded to different soils. Verification based on seven soil types indicated that the established simplified double-factor model effectively estimates cumulative infiltration for film hole irrigation, with a small mean average error of 0.141–2.299 mm, a root mean square error of 0.177–2.722 mm, a percent bias of −2.131–1.479%, and a large Nash–Sutcliffe coefficient that is close to 1.0.

  5. A GOMS model applied to a simplified control panel design

    International Nuclear Information System (INIS)

    Chavez, C.; Edwards, R.M.

    1992-01-01

    The design of the user interface for a new system requires many decisions to be considered. To develop sensitivity to user needs requires understanding user behavior. The how-to-do-it knowledge is a mixture of task-related and interface-related components. A conscientious analysis of these components, allows the designer to construct a model in terms of goals, operators, methods, and selection (GOMS model) rules that can be advantageously used in the design process and evaluation of a user interface. The emphasis of the present work is on describing the importance and use of a GOMS model as a formal user interface analysis tool in the development of a simplified panel for the control of a nuclear power plant. At Pennsylvania State University, a highly automated control system with a greatly simplified human interface has been proposed to improve power plant safety. Supervisory control is to be conducted with a simplified control panel with the following functions: startup, shutdown, increase power, decrease power, reset, and scram. Initial programming of the operator interface has been initiated within the framework of a U.S. Department of Energy funded university project for intelligent distributed control. A hypothesis to be tested is that this scheme can be also used to estimate mental work load content and predict human performance

  6. Updated thermal model using simplified short-wave radiosity calculations

    International Nuclear Information System (INIS)

    Smith, J.A.; Goltz, S.M.

    1994-01-01

    An extension to a forest canopy thermal radiance model is described that computes the short-wave energy flux absorbed within the canopy by solving simplified radiosity equations describing flux transfers between canopy ensemble classes partitioned by vegetation layer and leaf slope. Integrated short-wave reflectance and transmittance-factors obtained from measured leaf optical properties were found to be nearly equal for the canopy studied. Short-wave view factor matrices were approximated by combining the average leaf scattering coefficient with the long-wave view factor matrices already incorporated in the model. Both the updated and original models were evaluated for a dense spruce fir forest study site in Central Maine. Canopy short-wave absorption coefficients estimated from detailed Monte Carlo ray tracing calculations were 0.60, 0.04, and 0.03 for the top, middle, and lower canopy layers corresponding to leaf area indices of 4.0, 1.05, and 0.25. The simplified radiosity technique yielded analogous absorption values of 0.55, 0.03, and 0.01. The resulting root mean square error in modeled versus measured canopy temperatures for all layers was less than 1°C with either technique. Maximum error in predicted temperature using the simplified radiosity technique was approximately 2°C during peak solar heating. (author)

  7. Updated thermal model using simplified short-wave radiosity calculations

    Energy Technology Data Exchange (ETDEWEB)

    Smith, J. A.; Goltz, S. M.

    1994-02-15

    An extension to a forest canopy thermal radiance model is described that computes the short-wave energy flux absorbed within the canopy by solving simplified radiosity equations describing flux transfers between canopy ensemble classes partitioned by vegetation layer and leaf slope. Integrated short-wave reflectance and transmittance-factors obtained from measured leaf optical properties were found to be nearly equal for the canopy studied. Short-wave view factor matrices were approximated by combining the average leaf scattering coefficient with the long-wave view factor matrices already incorporated in the model. Both the updated and original models were evaluated for a dense spruce fir forest study site in Central Maine. Canopy short-wave absorption coefficients estimated from detailed Monte Carlo ray tracing calculations were 0.60, 0.04, and 0.03 for the top, middle, and lower canopy layers corresponding to leaf area indices of 4.0, 1.05, and 0.25. The simplified radiosity technique yielded analogous absorption values of 0.55, 0.03, and 0.01. The resulting root mean square error in modeled versus measured canopy temperatures for all layers was less than 1°C with either technique. Maximum error in predicted temperature using the simplified radiosity technique was approximately 2°C during peak solar heating. (author)

  8. Fast Edge Detection and Segmentation of Terrestrial Laser Scans Through Normal Variation Analysis

    Science.gov (United States)

    Che, E.; Olsen, M. J.

    2017-09-01

    Terrestrial Laser Scanning (TLS) utilizes light detection and ranging (lidar) to effectively and efficiently acquire point cloud data for a wide variety of applications. Segmentation is a common procedure of post-processing to group the point cloud into a number of clusters to simplify the data for the sequential modelling and analysis needed for most applications. This paper presents a novel method to rapidly segment TLS data based on edge detection and region growing. First, by computing the projected incidence angles and performing the normal variation analysis, the silhouette edges and intersection edges are separated from the smooth surfaces. Then a modified region growing algorithm groups the points lying on the same smooth surface. The proposed method efficiently exploits the gridded scan pattern utilized during acquisition of TLS data from most sensors and takes advantage of parallel programming to process approximately 1 million points per second. Moreover, the proposed segmentation does not require estimation of the normal at each point, which limits the errors in normal estimation propagating to segmentation. Both an indoor and outdoor scene are used for an experiment to demonstrate and discuss the effectiveness and robustness of the proposed segmentation method.

  9. Simplified analytical solutions for free drops during NCT for radioactive material packagings

    International Nuclear Information System (INIS)

    Gupta, N.K.

    1997-01-01

    To ensure structural integrity during normal conditions of transport (NCT), Federal regulations in 10CFR71.71 require that the nuclear material package designs be evaluated for the effects of free drops. The vessel stress acceptance criteria for these drops are given in Regulatory Guide 7.6 and ASME Section III Code. During initial phases of the package design, the effects of the NCT free drops can be evaluated by simplified analytical solutions which will ensure that the safety margins specified in R. G. 7.6 are met. These safety margins can be verified during the final stages of the package design with dynamic analyses using finite element methods. This paper calculates the maximum impact open-quotes gclose quotes loading on the vessels using single degree of freedom models for different drop orientations. Only end, bottom, and corner drops are analyzed for cylindrical packages or packages with cylindrical ends

  10. Customization of stock eye prosthesis for a pediatric patient by a simplified technique.

    Science.gov (United States)

    Jurel, Sunit Kumar; Talwar, Naina; Chand, Pooran; Singh, Raghuwar D; Gupta, Durga Shanker

    2012-05-01

    The unfortunate loss or absence of an eye may be caused by congenital defect , irreparable trauma, tumor or blind eye. The role of the maxillofacial prosthodontist in fabricating an ocular prosthesis to restore facial symmetry and normal appearance for the anophthalmic patient becomes essential. A custom-made ocular prosthesis is an excellent alternative for the people who lose their eye especially in young age. It has acceptable fit, retention and esthetics but is technically difficult to fabricate. On the other hand the stock eye has compromised fit and poor esthetics. Our case report presents a simple technique of customization of stock eye prosthesis to provide accurate fit and acceptable esthetics. How to cite this article: Jurel SK, Talwar N, Chand P, Singh RD, Gupta DS. Customization of Stock Eye Prosthesis for a Pediatric Patient by a Simplified Technique. Int J Clin Pediatr Dent 2012;5(2):155-158.

  11. Stability and bifurcation in a simplified four-neuron BAM neural network with multiple delays

    Directory of Open Access Journals (Sweden)

    2006-01-01

    Full Text Available We first study the distribution of the zeros of a fourth-degree exponential polynomial. Then we apply the obtained results to a simplified bidirectional associated memory (BAM neural network with four neurons and multiple time delays. By taking the sum of the delays as the bifurcation parameter, it is shown that under certain assumptions the steady state is absolutely stable. Under another set of conditions, there are some critical values of the delay, when the delay crosses these critical values, the Hopf bifurcation occurs. Furthermore, some explicit formulae determining the stability and the direction of periodic solutions bifurcating from Hopf bifurcations are obtained by applying the normal form theory and center manifold reduction. Numerical simulations supporting the theoretical analysis are also included.

  12. A simplified thermal model for a clothed human operator with thermoregulation

    Directory of Open Access Journals (Sweden)

    Zahid Akhtar khan

    2010-09-01

    Full Text Available This paper presents a simplified yet comprehensive mathematical model to predict steady state temperature distribution for various regions of male clothed human operators who are healthy, passive/active and lean/obese under the influence of different environmental conditions using thermoregulatory control concept. The present model is able to predict the core temperature, close to 37oC for a healthy, passive/active and lean/obese operator at normal ambient temperatures. It is observed that due to increase in body fat, BF the skin temperature, of the operator decreases by a small amount. However, effect of age of the operator on is found to be insignificant. The present model has been validated against the experimental data available in the literature.

  13. Exact Solution of the Gyration Radius of an Individual's Trajectory for a Simplified Human Regular Mobility Model

    Science.gov (United States)

    Yan, Xiao-Yong; Han, Xiao-Pu; Zhou, Tao; Wang, Bing-Hong

    2011-12-01

    We propose a simplified human regular mobility model to simulate an individual's daily travel with three sequential activities: commuting to workplace, going to do leisure activities and returning home. With the assumption that the individual has a constant travel speed and inferior limit of time at home and in work, we prove that the daily moving area of an individual is an ellipse, and finally obtain an exact solution of the gyration radius. The analytical solution captures the empirical observation well.

  14. Quench limits

    International Nuclear Information System (INIS)

    Sapinski, M.

    2012-01-01

    With thirteen beam induced quenches and numerous Machine Development tests, the current knowledge of LHC magnets quench limits still contains a lot of unknowns. Various approaches to determine the quench limits are reviewed and results of the tests are presented. Attempt to reconstruct a coherent picture emerging from these results is taken. The available methods of computation of the quench levels are presented together with dedicated particle shower simulations which are necessary to understand the tests. The future experiments, needed to reach better understanding of quench limits as well as limits for the machine operation are investigated. The possible strategies to set BLM (Beam Loss Monitor) thresholds are discussed. (author)

  15. Statistical Mechanics of a Simplified Bipartite Matching Problem: An Analytical Treatment

    Science.gov (United States)

    Dell'Erba, Matías Germán

    2012-03-01

    We perform an analytical study of a simplified bipartite matching problem in which there exists a constant matching energy, and both heterosexual and homosexual pairings are allowed. We obtain the partition function in a closed analytical form and we calculate the corresponding thermodynamic functions of this model. We conclude that the model is favored at high temperatures, for which the probabilities of heterosexual and homosexual pairs tend to become equal. In the limits of low and high temperatures, the system is extensive, however this property is lost in the general case. There exists a relation between the matching energies for which the system becomes more stable under external (thermal) perturbations. As the difference of energies between the two possible matches increases the system becomes more ordered, while the maximum of entropy is achieved when these energies are equal. In this limit, there is a first order phase transition between two phases with constant entropy.

  16. Baby Poop: What's Normal?

    Science.gov (United States)

    ... I'm breast-feeding my newborn and her bowel movements are yellow and mushy. Is this normal for baby poop? Answers from Jay L. Hoecker, M.D. Yellow, mushy bowel movements are perfectly normal for breast-fed babies. Still, ...

  17. Visual Memories Bypass Normalization.

    Science.gov (United States)

    Bloem, Ilona M; Watanabe, Yurika L; Kibbe, Melissa M; Ling, Sam

    2018-05-01

    How distinct are visual memory representations from visual perception? Although evidence suggests that briefly remembered stimuli are represented within early visual cortices, the degree to which these memory traces resemble true visual representations remains something of a mystery. Here, we tested whether both visual memory and perception succumb to a seemingly ubiquitous neural computation: normalization. Observers were asked to remember the contrast of visual stimuli, which were pitted against each other to promote normalization either in perception or in visual memory. Our results revealed robust normalization between visual representations in perception, yet no signature of normalization occurring between working memory stores-neither between representations in memory nor between memory representations and visual inputs. These results provide unique insight into the nature of visual memory representations, illustrating that visual memory representations follow a different set of computational rules, bypassing normalization, a canonical visual computation.

  18. A simplified approach to the PROMETHEE method for priority setting in management of mine action projects

    Directory of Open Access Journals (Sweden)

    Marko Mladineo

    2016-12-01

    Full Text Available In the last 20 years, priority setting in mine actions, i.e. in humanitarian demining, has become an increasingly important topic. Given that mine action projects require management and decision-making based on a multi -criteria approach, multi-criteria decision-making methods like PROMETHEE and AHP have been used worldwide for priority setting. However, from the aspect of mine action, where stakeholders in the decision-making process for priority setting are project managers, local politicians, leaders of different humanitarian organizations, or similar, applying these methods can be difficult. Therefore, a specialized web-based decision support system (Web DSS for priority setting, developed as part of the FP7 project TIRAMISU, has been extended using a module for developing custom priority setting scenarios in line with an exceptionally easy, user-friendly approach. The idea behind this research is to simplify the multi-criteria analysis based on the PROMETHEE method. Therefore, a simplified PROMETHEE method based on statistical analysis for automated suggestions of parameters such as preference function thresholds, interactive selection of criteria weights, and easy input of criteria evaluations is presented in this paper. The result is web-based DSS that can be applied worldwide for priority setting in mine action. Additionally, the management of mine action projects is supported using modules for providing spatial data based on the geographic information system (GIS. In this paper, the benefits and limitations of a simplified PROMETHEE method are presented using a case study involving mine action projects, and subsequently, certain proposals are given for the further research.

  19. Dose limits

    International Nuclear Information System (INIS)

    Fitoussi, L.

    1987-12-01

    The dose limit is defined to be the level of harmfulness which must not be exceeded, so that an activity can be exercised in a regular manner without running a risk unacceptable to man and the society. The paper examines the effects of radiation categorised into stochastic and non-stochastic. Dose limits for workers and the public are discussed

  20. Making nuclear 'normal'

    International Nuclear Information System (INIS)

    Haehlen, Peter; Elmiger, Bruno

    2000-01-01

    The mechanics of the Swiss NPPs' 'come and see' programme 1995-1999 were illustrated in our contributions to all PIME workshops since 1996. Now, after four annual 'waves', all the country has been covered by the NPPs' invitation to dialogue. This makes PIME 2000 the right time to shed some light on one particular objective of this initiative: making nuclear 'normal'. The principal aim of the 'come and see' programme, namely to give the Swiss NPPs 'a voice of their own' by the end of the nuclear moratorium 1990-2000, has clearly been attained and was commented on during earlier PIMEs. It is, however, equally important that Swiss nuclear energy not only made progress in terms of public 'presence', but also in terms of being perceived as a normal part of industry, as a normal branch of the economy. The message that Swiss nuclear energy is nothing but a normal business involving normal people, was stressed by several components of the multi-prong campaign: - The speakers in the TV ads were real - 'normal' - visitors' guides and not actors; - The testimonials in the print ads were all real NPP visitors - 'normal' people - and not models; - The mailings inviting a very large number of associations to 'come and see' activated a typical channel of 'normal' Swiss social life; - Spending money on ads (a new activity for Swiss NPPs) appears to have resulted in being perceived by the media as a normal branch of the economy. Today we feel that the 'normality' message has well been received by the media. In the controversy dealing with antinuclear arguments brought forward by environmental organisations journalists nowadays as a rule give nuclear energy a voice - a normal right to be heard. As in a 'normal' controversy, the media again actively ask themselves questions about specific antinuclear claims, much more than before 1990 when the moratorium started. The result is that in many cases such arguments are discarded by journalists, because they are, e.g., found to be

  1. 20 CFR 336.2 - Duration of normal unemployment benefits.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Duration of normal unemployment benefits. 336... UNEMPLOYMENT INSURANCE ACT DURATION OF NORMAL AND EXTENDED BENEFITS Normal Benefits § 336.2 Duration of normal unemployment benefits. (a) 130 compensable day limitation. A qualified employee who has satisfied the waiting...

  2. Inverse Limits

    CERN Document Server

    Ingram, WT

    2012-01-01

    Inverse limits provide a powerful tool for constructing complicated spaces from simple ones. They also turn the study of a dynamical system consisting of a space and a self-map into a study of a (likely more complicated) space and a self-homeomorphism. In four chapters along with an appendix containing background material the authors develop the theory of inverse limits. The book begins with an introduction through inverse limits on [0,1] before moving to a general treatment of the subject. Special topics in continuum theory complete the book. Although it is not a book on dynamics, the influen

  3. Normal Pressure Hydrocephalus

    Science.gov (United States)

    ... improves the chance of a good recovery. Without treatment, symptoms may worsen and cause death. What research is being done? The NINDS conducts and supports research on neurological disorders, including normal pressure hydrocephalus. Research on disorders such ...

  4. Normality in Analytical Psychology

    Science.gov (United States)

    Myers, Steve

    2013-01-01

    Although C.G. Jung’s interest in normality wavered throughout his career, it was one of the areas he identified in later life as worthy of further research. He began his career using a definition of normality which would have been the target of Foucault’s criticism, had Foucault chosen to review Jung’s work. However, Jung then evolved his thinking to a standpoint that was more aligned to Foucault’s own. Thereafter, the post Jungian concept of normality has remained relatively undeveloped by comparison with psychoanalysis and mainstream psychology. Jung’s disjecta membra on the subject suggest that, in contemporary analytical psychology, too much focus is placed on the process of individuation to the neglect of applications that consider collective processes. Also, there is potential for useful research and development into the nature of conflict between individuals and societies, and how normal people typically develop in relation to the spectrum between individuation and collectivity. PMID:25379262

  5. Normal pressure hydrocephalus

    Science.gov (United States)

    Hydrocephalus - occult; Hydrocephalus - idiopathic; Hydrocephalus - adult; Hydrocephalus - communicating; Dementia - hydrocephalus; NPH ... Ferri FF. Normal pressure hydrocephalus. In: Ferri FF, ed. ... Elsevier; 2016:chap 648. Rosenberg GA. Brain edema and disorders ...

  6. Normal Functioning Family

    Science.gov (United States)

    ... Spread the Word Shop AAP Find a Pediatrician Family Life Medical Home Family Dynamics Adoption & Foster Care ... Español Text Size Email Print Share Normal Functioning Family Page Content Article Body Is there any way ...

  7. Normal growth and development

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/article/002456.htm Normal growth and development To use the sharing features on this page, please enable JavaScript. A child's growth and development can be divided into four periods: ...

  8. A simplified approach for evaluating secondary stresses in elevated temperature design

    International Nuclear Information System (INIS)

    Becht, C.

    1983-01-01

    Control of secondary stresses is important for long-term reliability of components, particularly at elevated temperatures where substantial creep damage can occur and result in cracking. When secondary stresses are considered in the design of elevated temperature components, these are often addressed by the criteria contained in Nuclear Code Case N-47 for use with elastic or inelastic analysis. The elastic rules are very conservative as they bound a large range of complex phenomena; because of this conservatism, only components in relatively mild services can be designed in accordance with these rules. The inelastic rules, although more accurate, require complex and costly nonlinear analysis. Elevated temperature shakedown is a recognized phenomenon that has been considered in developing Code rules and simplified methods. This paper develops and examines the implications of using a criteria which specifically limits stresses to the shakedown regime. Creep, fatigue, and strain accumulation are considered. The effect of elastic follow-up on the conservatism of the criteria is quantified by means of a simplified method. The level of conservatism is found to fall between the elastic and inelastic rules of N-47 and, in fact, the incentives for performing complex inelastic analyses appear to be low except in the low cycle regime. The criteria has immediate applicability to non-code components such as vessel internals in the chemical, petroleum, and synfuels industry. It is suggested that such a criteria be considered in future code rule development

  9. Hybrid simplified spherical harmonics with diffusion equation for light propagation in tissues

    International Nuclear Information System (INIS)

    Chen, Xueli; Sun, Fangfang; Yang, Defu; Ren, Shenghan; Liang, Jimin; Zhang, Qian

    2015-01-01

    Aiming at the limitations of the simplified spherical harmonics approximation (SP N ) and diffusion equation (DE) in describing the light propagation in tissues, a hybrid simplified spherical harmonics with diffusion equation (HSDE) based diffuse light transport model is proposed. In the HSDE model, the living body is first segmented into several major organs, and then the organs are divided into high scattering tissues and other tissues. DE and SP N are employed to describe the light propagation in these two kinds of tissues respectively, which are finally coupled using the established boundary coupling condition. The HSDE model makes full use of the advantages of SP N and DE, and abandons their disadvantages, so that it can provide a perfect balance between accuracy and computation time. Using the finite element method, the HSDE is solved for light flux density map on body surface. The accuracy and efficiency of the HSDE are validated with both regular geometries and digital mouse model based simulations. Corresponding results reveal that a comparable accuracy and much less computation time are achieved compared with the SP N model as well as a much better accuracy compared with the DE one. (paper)

  10. Feasibility of using of a simplified question in assessing diet quality of adolescents.

    Science.gov (United States)

    Rodrigues, Paulo Rogério Melo; Gonçalves-Silva, Regina Maria Veras; Ferreira, Márcia Gonçalves; Pereira, Rosangela Alves

    2017-05-01

    This study aims to analyze the applicability of a simplified question in assessing diet quality of adolescents in a cross-sectional school-based study carried out in a sample of high school students. Diet quality self-perception was obtained when the participant was inquired about own diet considering "excellent", "good", "fair" or "poor" responses. We evaluated meals habits and food intake through food frequency questionnaire. The revised version of the Brazilian Healthy Eating Index (BHEI-R) was estimated and we identified three dietary patterns using factor analysis. "Good" self-perceived diet quality was reported by 56% of adolescents and was associated with regular consumption of fruits and vegetables, meal profile and high healthy eating index scores. However, consumption of foods harmful to health was not perceived as characteristic that affects diet quality. The evaluated question showed sensitivity of 28% to detect good quality diets and specificity of 79% to identify low nutritional value diets. The use of a simplified question to assess dietary habits of adolescents is limited, since the consumption of high-fat, high-sugar and high-sodium food was not recognized as an indicator of low quality diet.

  11. On equivalent parameter learning in simplified feature space based on Bayesian asymptotic analysis.

    Science.gov (United States)

    Yamazaki, Keisuke

    2012-07-01

    Parametric models for sequential data, such as hidden Markov models, stochastic context-free grammars, and linear dynamical systems, are widely used in time-series analysis and structural data analysis. Computation of the likelihood function is one of primary considerations in many learning methods. Iterative calculation of the likelihood such as the model selection is still time-consuming though there are effective algorithms based on dynamic programming. The present paper studies parameter learning in a simplified feature space to reduce the computational cost. Simplifying data is a common technique seen in feature selection and dimension reduction though an oversimplified space causes adverse learning results. Therefore, we mathematically investigate a condition of the feature map to have an asymptotically equivalent convergence point of estimated parameters, referred to as the vicarious map. As a demonstration to find vicarious maps, we consider the feature space, which limits the length of data, and derive a necessary length for parameter learning in hidden Markov models. Copyright © 2012 Elsevier Ltd. All rights reserved.

  12. Simplified dark matter models with two Higgs doublets. I. Pseudoscalar mediators

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, Martin [Heidelberg Univ. (Germany). Inst. fuer Theoretische Physik; Haisch, Ulrich [Oxford Univ. (United Kingdom). Rudolf Peierls Centre for Theoretical Physics; CERN, Geneva (Switzerland). Theoretical Physics Dept.; Kahlhoefer, Felix [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

    2017-01-15

    We study a new class of renormalisable simplified models for dark matter searches at the LHC that are based on two Higgs doublet models with an additional pseudoscalar mediator. In contrast to the spin-0 simplified models employed in analyses of Run I data these models are self-consistent, unitary and bounds from Higgs physics typically pose no constraints. Predictions for various missing transverse energy (E{sub T,miss}) searches are discussed and the reach of the 13 TeV LHC is explored. It is found that the proposed models provide a rich spectrum of complementary observables that lead to non-trivial constraints. We emphasise in this context the sensitivity of the t anti t+E{sub T,miss}, mono-Z and mono-Higgs channels, which yield stronger limits than mono-jet searches in large parts of the parameter space. Constraints from spin-0 resonance searches, electroweak precision measurements and flavour observables are also derived and shown to provide further important handles to constraint and to test the considered dark matter models.

  13. Influence of simplified nutrition labeling and taxation on laboratory energy intake in adults.

    Science.gov (United States)

    Temple, Jennifer L; Johnson, Karena M; Archer, Kelli; Lacarte, Allison; Yi, Christina; Epstein, Leonard H

    2011-08-01

    The purpose of these studies was to test the hypotheses that simplified nutrition labeling and taxation alter food selection and intake. In Experiment 1, participants consumed lunch in the laboratory three times with no labels, standard nutrition labels, or traffic light diet labels at each visit. In Experiment 2, participants were given $6.00 with which to purchase lunch in the laboratory twice with standard pricing on one visit and a 25% tax on "red" foods on another visit. Participants received a brief education session on the labeling systems being used. Total energy intake and energy intake and number of foods purchased from each traffic light category were measured. Nutrition labeling decreased energy intake in lean females, but had no effect in men or in obese females. Traffic light labels increased consumption of "green" foods and decreased consumption of "red" foods. Taxation decreased the purchasing of "red" foods in obese, but not non-obese participants. There were no interactions between taxation and simplified nutrition labeling. Although generalization to real-world purchasing and consumption is limited by the laboratory study design, our findings suggests that taking multiple, simultaneous approaches to reduce energy intake may have the greatest impact on food purchases and/or nutrient consumption. Copyright © 2011 Elsevier Ltd. All rights reserved.

  14. Hybrid simplified spherical harmonics with diffusion equation for light propagation in tissues.

    Science.gov (United States)

    Chen, Xueli; Sun, Fangfang; Yang, Defu; Ren, Shenghan; Zhang, Qian; Liang, Jimin

    2015-08-21

    Aiming at the limitations of the simplified spherical harmonics approximation (SPN) and diffusion equation (DE) in describing the light propagation in tissues, a hybrid simplified spherical harmonics with diffusion equation (HSDE) based diffuse light transport model is proposed. In the HSDE model, the living body is first segmented into several major organs, and then the organs are divided into high scattering tissues and other tissues. DE and SPN are employed to describe the light propagation in these two kinds of tissues respectively, which are finally coupled using the established boundary coupling condition. The HSDE model makes full use of the advantages of SPN and DE, and abandons their disadvantages, so that it can provide a perfect balance between accuracy and computation time. Using the finite element method, the HSDE is solved for light flux density map on body surface. The accuracy and efficiency of the HSDE are validated with both regular geometries and digital mouse model based simulations. Corresponding results reveal that a comparable accuracy and much less computation time are achieved compared with the SPN model as well as a much better accuracy compared with the DE one.

  15. Simplified predictive models for CO2 sequestration performance assessment

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, Srikanta [Battelle Memorial Inst., Columbus, OH (United States); Ganesh, Priya [Battelle Memorial Inst., Columbus, OH (United States); Schuetter, Jared [Battelle Memorial Inst., Columbus, OH (United States); He, Jincong [Battelle Memorial Inst., Columbus, OH (United States); Jin, Zhaoyang [Battelle Memorial Inst., Columbus, OH (United States); Durlofsky, Louis J. [Battelle Memorial Inst., Columbus, OH (United States)

    2015-09-30

    Latin Hypercube sampling (LHS) based design with a multidimensional kriging metamodel fit. For roughly the same number of simulations, the LHS-based metamodel yields a more robust predictive model, as verified by a k-fold cross-validation approach (with data split into training and test sets) as well by validation with an independent dataset. In the third category, a reduced-order modeling procedure is utilized that combines proper orthogonal decomposition (POD) for reducing problem dimensionality with trajectory-piecewise linearization (TPWL) in order to represent system response at new control settings from a limited number of training runs. Significant savings in computational time are observed with reasonable accuracy from the PODTPWL reduced-order model for both vertical and horizontal well problems – which could be important in the context of history matching, uncertainty quantification and optimization problems. The simplified physics and statistical learning based models are also validated using an uncertainty analysis framework. Reference cumulative distribution functions of key model outcomes (i.e., plume radius and reservoir pressure buildup) generated using a 97-run full-physics simulation are successfully validated against the CDF from 10,000 sample probabilistic simulations using the simplified models. The main contribution of this research project is the development and validation of a portfolio of simplified modeling approaches that will enable rapid feasibility and risk assessment for CO2 sequestration in deep saline formations.

  16. The cost of simplifying air travel when modeling disease spread.

    Directory of Open Access Journals (Sweden)

    Justin Lessler

    Full Text Available BACKGROUND: Air travel plays a key role in the spread of many pathogens. Modeling the long distance spread of infectious disease in these cases requires an air travel model. Highly detailed air transportation models can be over determined and computationally problematic. We compared the predictions of a simplified air transport model with those of a model of all routes and assessed the impact of differences on models of infectious disease. METHODOLOGY/PRINCIPAL FINDINGS: Using U.S. ticket data from 2007, we compared a simplified "pipe" model, in which individuals flow in and out of the air transport system based on the number of arrivals and departures from a given airport, to a fully saturated model where all routes are modeled individually. We also compared the pipe model to a "gravity" model where the probability of travel is scaled by physical distance; the gravity model did not differ significantly from the pipe model. The pipe model roughly approximated actual air travel, but tended to overestimate the number of trips between small airports and underestimate travel between major east and west coast airports. For most routes, the maximum number of false (or missed introductions of disease is small (<1 per day but for a few routes this rate is greatly underestimated by the pipe model. CONCLUSIONS/SIGNIFICANCE: If our interest is in large scale regional and national effects of disease, the simplified pipe model may be adequate. If we are interested in specific effects of interventions on particular air routes or the time for the disease to reach a particular location, a more complex point-to-point model will be more accurate. For many problems a hybrid model that independently models some frequently traveled routes may be the best choice. Regardless of the model used, the effect of simplifications and sensitivity to errors in parameter estimation should be analyzed.

  17. 48 CFR 1552.232-74 - Payments-simplified acquisition procedures financing.

    Science.gov (United States)

    2010-10-01

    ... acquisition procedures financing. 1552.232-74 Section 1552.232-74 Federal Acquisition Regulations System... Provisions and Clauses 1552.232-74 Payments—simplified acquisition procedures financing. As prescribed in... acquisition procedures financing. Payments—Simplified Acquisition Procedures Financing (JUN 2006) Simplified...

  18. A Simplified Supercritical Fast Reactor with Thorium Fuel

    OpenAIRE

    Peng Zhang; Kan Wang; Ganglin Yu

    2014-01-01

    Super-Critical water-cooled Fast Reactor (SCFR) is a feasible option for the Gen-IV SCWR designs, in which much less moderator and thus coolant are needed for transferring the fission heat from the core compared with the traditional LWRs. The fast spectrum of SCFR is useful for fuel breeding and thorium utilization, which is then beneficial for enhancing the sustainability of the nuclear fuel cycle. A SCFR core is constructed in this work, with the aim of simplifying the mechanical structure ...

  19. On mono-W signatures in spin-1 simplified models

    Directory of Open Access Journals (Sweden)

    Ulrich Haisch

    2016-09-01

    Full Text Available The potential sensitivity to isospin-breaking effects makes LHC searches for mono-W signatures promising probes of the coupling structure between the Standard Model and dark matter. It has been shown, however, that the strong sensitivity of the mono-W channel to the relative magnitude and sign of the up-type and down-type quark couplings to dark matter is an artifact of unitarity violation. We provide three different solutions to this mono-W problem in the context of spin-1 simplified models and briefly discuss the impact that our findings have on the prospects of mono-W searches at future LHC runs.

  20. Comments on Simplified Calculation Method for Fire Exposed Concrete Columns

    DEFF Research Database (Denmark)

    Hertz, Kristian Dahl

    1998-01-01

    The author has developed new simplified calculation methods for fire exposed columns. Methods, which are found In ENV 1992-1-2 chapter 4.3 and in proposal for Danish code of Practise DS411 chapter 9. In the present supporting document the methods are derived and 50 eccentrically loaded fire expos...... columns are calculated and compared to results of full-scale tests. Furthermore 500 columns are calculated in order to present each test result related to a variation of the calculation in time of fire resistance....

  1. Technology Solutions Case Study: Combustion Safety Simplified Test Protocol

    Energy Technology Data Exchange (ETDEWEB)

    L. Brand, D. Cautley, D. Bohac, P. Francisco, L. Shen, and S. Gloss

    2015-12-01

    Combustions safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives.

  2. Simplified simulation of multicomponent isotope separation by gas centrifuge

    International Nuclear Information System (INIS)

    Guo Zhixiong; Ying Chuntong

    1995-01-01

    The expressions of diffusion equation for multicomponent isotope separation by gas centrifuge are derived by utilizing the simplified diffusion transport vector. A method of radial averaging which was restricted to a binary mixture is extended to multicomponent isotope mixtures by using an iterative scheme. A numerical analysis of tetradic UF 6 or SF 6 gas isotope separation by centrifuge is discussed when a special model of velocity distribution is given. The dependence of mutual separation factor for the components on their molecular weights' difference is obtained. Some aspects of the given model of gas fluid are also discussed

  3. Simplified numerical simulation of hot channel in sodium cooled reactor

    International Nuclear Information System (INIS)

    Fonseca, F. de A.S. da; Silva Filho, E.

    1988-12-01

    The thermal-hydraulic parameter values that restrict the operation of a liquid sodium cooled reactor are not established by the average conditions of the coolant in the reactor core but by the extreme conditions of the hot channel. The present work was developed to analysis of hot channel of a sodium cooled reactor, adapting to this reactor an existent simplified model for hot channel of pressurized water reactor. The model was applied for a standard sodium reactor and the results are considered satisfatory. (author) [pt

  4. Simplified hourly method to calculate summer temperatures in dwellings

    DEFF Research Database (Denmark)

    Mortensen, Lone Hedegaard; Aggerholm, Søren

    2012-01-01

    with an ordinary distribution of windows and a “worst” case where the window area facing south and west was increased by more than 60%. The simplified method used Danish weather data and only needs information on transmission losses, thermal mass, surface contact, internal load, ventilation scheme and solar load...... program for thermal simulations of buildings. The results are based on one year simulations of two cases. The cases were based on a low energy dwelling of 196 m². The transmission loss for the building envelope was 3.3 W/m², not including windows and doors. The dwelling was tested in two cases, a case...

  5. On mono-W signatures in spin-1 simplified models

    International Nuclear Information System (INIS)

    Haisch, Ulrich; Tait, Tim M.P.

    2016-03-01

    The potential sensitivity to isospin-breaking effects makes LHC searches for mono-W signatures promising probes of the coupling structure between the Standard Model and dark matter. It has been shown, however, that the strong sensitivity of the mono-W channel to the relative magnitude and sign of the up-type and down-type quark couplings to dark matter is an artefact of unitarity violation. We provide three different solutions to this mono-W problem in the context of spin-1 simplified models and briefly discuss the impact that our findings have on the prospects of mono-W searches at future LHC runs.

  6. Simplified analysis of trasients in pool type liquid metal reactors

    International Nuclear Information System (INIS)

    Botelho, D.A.

    1987-01-01

    The conceptual design of a liquid metal fast breeder reactor will require a great effort of development in several technical disciplines. One of them is the thermal-hydraulic design of the reactor and of the heat and fluid transport components inside the reactor vessel. A simplified model to calculate the maximum sodium temperatures is presented in this paper. This model can be used to optimize the layout of components inside the reactor vessel and was easily programmed in a small computer. Illustrative calculations of two transients of a typical hot pool type fast reactor are presented and compared with the results of other researchers. (author) [pt

  7. Location audio simplified capturing your audio and your audience

    CERN Document Server

    Miles, Dean

    2014-01-01

    From the basics of using camera, handheld, lavalier, and shotgun microphones to camera calibration and mixer set-ups, Location Audio Simplified unlocks the secrets to clean and clear broadcast quality audio no matter what challenges you face. Author Dean Miles applies his twenty-plus years of experience as a professional location operator to teach the skills, techniques, tips, and secrets needed to produce high-quality production sound on location. Humorous and thoroughly practical, the book covers a wide array of topics, such as:* location selection* field mixing* boo

  8. A simplified biosphere model for global climate studies

    Science.gov (United States)

    Xue, Y.; Sellers, P. J.; Kinter, J. L.; Shukla, J.

    1991-01-01

    A comprehensive analysis of the simple biosphere model (SIB) of Sellers et al. (1986) is performed in an effort to bridge the gap between the typical hydrological treatment of the land surface biosphere and the conventional general circulation model treatment, which is specified through a single parameter. Approximations are developed that stimulate the effects of reduced soil moisture more simply, maintaining the essence of the biophysical concepts utilized in SIB. Comparing the reduced parameter biosphere with those from the original formulation in a GCM and a zero-dimensional model shows the simplified version to reproduce the original results quite closely.

  9. A simplified model of top-flavoured dark matter

    Energy Technology Data Exchange (ETDEWEB)

    Kast, Simon; Blanke, Monika [Karlsruher Institut fuer Technologie, Karlsruhe (Germany)

    2016-07-01

    We present the phenomenology of a new physics simplified model of top-flavoured dark matter. The dark matter particle is the lightest Dirac fermion of a new flavour-triplet coupling to the SM up-triplet via a new scalar mediator. The coupling is left general, following Dark Minimal Flavour Violation introduced in arXiv:1405.6709, and therefore is a new source of flavour violation. We study the impact of constraints from both flavour experiments, relic abundance and direct detection constraints, as well as collider bounds.

  10. Rationale simplified hardening training and recreational complexes future teachers

    Directory of Open Access Journals (Sweden)

    Verbludov I.B.

    2010-02-01

    Full Text Available Distribution in the modern world epidemiological diseases are influenza and acute respiratory viral infections requires a search for simplified, effective preventive means. The main direction of prevention of these diseases is to strengthen and enhance the activities of the immune system. Strengthening the protective systems of the body is directly related to the constant holding of different types of hardening. This study illustrates the possibility of using quenching air and water in the independent exercise training and recreational facilities in all conditions of students.

  11. International piping benchmarks: Use of simplified code PACE 2

    Energy Technology Data Exchange (ETDEWEB)

    Boyle, J; Spence, J [University of Strathclyde (United Kingdom); Blundell, C [Risley Nuclear Power Development Establishment, Central Technical Services, Risley, Warrington (United Kingdom)

    1979-06-01

    This report compares the results obtained using the code PACE 2 with the International Working Group on Fast Reactors (IWGFR) International Piping Benchmark solutions. PACE 2 is designed to analyse systems of pipework using a simplified method which is economical of computer time and hence inexpensive. This low cost is not achieved without some loss of accuracy in the solution, but for most parts of a system this inaccuracy is acceptable and those sections of particular importance may be reanalysed using more precise methods in order to produce a satisfactory analysis of the complete system at reasonable cost. (author)

  12. Simplified scaling model for the THETA-pinch

    Science.gov (United States)

    Ewing, K. J.; Thomson, D. B.

    1982-02-01

    A simple ID scaing model for the fast Theta pinch was developed and written as a code that would be flexible, inexpensive in computer time, and readily available for use with the Los Alamos explosive-driven high magnetic field program. The simplified model uses three successive separate stages: (1) a snowplow-like radial implosion, (2) an idealized resistive annihilation of reverse bias field, and (3) an adiabatic compression stage of a Beta = 1 plasma for which ideal pressure balance is assumed to hold. The code uses one adjustable fitting constant whose value was first determined by comparison with results from the Los Alamos Scylla III, Scyllacita, and Scylla IA Theta pinches.

  13. Simplified approach for estimating large early release frequency

    International Nuclear Information System (INIS)

    Pratt, W.T.; Mubayi, V.; Nourbakhsh, H.; Brown, T.; Gregory, J.

    1998-04-01

    The US Nuclear Regulatory Commission (NRC) Policy Statement related to Probabilistic Risk Analysis (PRA) encourages greater use of PRA techniques to improve safety decision-making and enhance regulatory efficiency. One activity in response to this policy statement is the use of PRA in support of decisions related to modifying a plant's current licensing basis (CLB). Risk metrics such as core damage frequency (CDF) and Large Early Release Frequency (LERF) are recommended for use in making risk-informed regulatory decisions and also for establishing acceptance guidelines. This paper describes a simplified approach for estimating LERF, and changes in LERF resulting from changes to a plant's CLB

  14. Simplified models for radiational losses calculating a tokamak plasma

    International Nuclear Information System (INIS)

    Arutiunov, A.B.; Krasheninnikov, S.I.; Prokhorov, D.Yu.

    1990-01-01

    To determine the magnitudes and profiles of radiational losses in a Tokamak plasma, particularly for high plasma densities, when formation of MARFE or detached-plasma takes place, it is necessary to know impurity distribution over the ionization states. Equations describing time evolution of this distribution are rather cumbersome, besides that, transport coefficients as well as rate constants of the processes involving complex ions are known nowadays with high degree of uncertainty, thus it is believed necessary to develop simplified, half-analytical models describing time evolution of the impurities analysis of physical processes taking place in a Tokamak plasma on the base of the experimental data. (author) 6 refs., 2 figs

  15. Simplified methodology for analysis of Angra-1 containing

    International Nuclear Information System (INIS)

    Neves Conti, T. das; Souza, A.L. de; Sabundjian, G.

    1988-01-01

    A simplified methodology of analysis was developed to simulate a Large Break Loss of Coolant Accident in the Angra 1 Nuclear Power Station. Using the RELAP5/MOD1, RELAP4/MOD5 and CONTEMPT-LT Codes, the time the variation of pressure and temperature in the containment was analysed. The obtained data was compared with the Angra 1 Final Safety Analysis Report, and too those calculated by a Detailed Model. The results obtained by this new methodology such as the small computational time of simulation, were satisfactory when getting the preliminar avaliation of the Angra 1 global parameters. (author) [pt

  16. A simplified approach to detect undervoltage tripping of wind generators

    Energy Technology Data Exchange (ETDEWEB)

    Sigrist, Lukas; Rouco, Luis [Universidad Pontificia Comillas, Madrid (Spain). Inst. de Investigacion Tecnologica

    2012-07-01

    This paper proposes a simplified but fast approach based on a Norton equivalent of wind generators to detect undervoltage tripping of wind generators. This approach is successfully applied to a real wind farm. The relevant grid code requires the wind farm to withstand a voltage dip of 0% retained voltage. The ability of the wind generators to raise the voltage supplying reactive current and to avoid undervoltage tripping is investigated. The obtained results are also compared with the results obtained from detailed dynamic simulations, which make use of wind generator models complying with the relevant grid code. (orig.)

  17. International piping benchmarks: Use of simplified code PACE 2

    International Nuclear Information System (INIS)

    Boyle, J.; Spence, J.; Blundell, C.

    1979-01-01

    This report compares the results obtained using the code PACE 2 with the International Working Group on Fast Reactors (IWGFR) International Piping Benchmark solutions. PACE 2 is designed to analyse systems of pipework using a simplified method which is economical of computer time and hence inexpensive. This low cost is not achieved without some loss of accuracy in the solution, but for most parts of a system this inaccuracy is acceptable and those sections of particular importance may be reanalysed using more precise methods in order to produce a satisfactory analysis of the complete system at reasonable cost. (author)

  18. Information security governance simplified from the boardroom to the keyboard

    CERN Document Server

    Fitzgerald, Todd

    2011-01-01

    Security practitioners must be able to build cost-effective security programs while also complying with government regulations. Information Security Governance Simplified: From the Boardroom to the Keyboard lays out these regulations in simple terms and explains how to use control frameworks to build an air-tight information security (IS) program and governance structure. Defining the leadership skills required by IS officers, the book examines the pros and cons of different reporting structures and highlights the various control frameworks available. It details the functions of the security d

  19. Quantitative thallium-201 myocardial exercise scintigraphy in normal subjects and patients with normal coronary arteries

    International Nuclear Information System (INIS)

    Niemeyer, M.G.; St. Antonius Hospital Nieuwegein; Laarman, G.J.; Lelbach, S.; Cramer, M.J.; Ascoop, C.A.P.L.; Verzijlbergen, J.F.; Wall, E.E. van der; Zwinderman, A.H.; Pauwels, E.K.J.

    1990-01-01

    Quantitative thallium-201 myocardial exercise scintigraphy was tested in two patient populations representing alternative standards for cardiac normality: group I comprised 18 male uncatherized patients with a low likelihood of coronary artery disease (CAD); group II contained 41 patients with normal coronary arteriograms. Group I patients were younger, they achieved a higher rate-pressure product than group II patients; all had normal findings by phisical examination and electrocardiography at rest and exercise. Group II patients comprised 21 females, 11 patients showed abnormal electrocardiography at rest, and five patients showed ischemic ST depression during exercise. Twelve patients had sign of minimal CAD. Twelve patients revealed abnormal visual and quantitative thallium findings, three of these patients had minimal CAD. Profiles of uptake and washout of thallium-201 were derived from both patient groups, and compared with normal limits developed by Maddahi et al. Furthermore, low likelihood and angiographically normal patients may differ substantially, and both sets of normal patients should be considered when establishing criteria of abnormality in exercise thallium imaging. When commercial software containing normal limits for quantitative analysis of exercise thallium-201 imaging is used in clinical practice, it is mandatory to compare these with normal limits of uptake and washout of thallium-201, derived from the less heterogeneous group of low-likelihood subjects, which should be used in selecting a normal population to define normality. (author). 37 refs.; 3 figs; 1 tab

  20. A Simplified Solution for Calculating the Phreatic Line and Slope Stability during a Sudden Drawdown of the Reservoir Water Level

    Directory of Open Access Journals (Sweden)

    Guanhua Sun

    2018-01-01

    Full Text Available On the basis of the Boussinesq unsteady seepage differential equation, a new simplified formula for the phreatic line of slopes under the condition of decreasing reservoir water level is derived by means of the Laplacian matrix and its inverse transform. In this context, the expression of normal stress on the slip surface under seepage forces is deduced, and a procedure for obtaining the safety factors under hydrodynamic forces is proposed. A case study of the Three Gorges Reservoir is used to analyze the influences of the water level, decreasing velocity and the permeability coefficient on slope stability.

  1. New approach for simplified and automated measurement of left ventricular ejection fraction by ECG gated blood pool scintigraphy

    Energy Technology Data Exchange (ETDEWEB)

    Inagaki, Suetsugu; Adachi, Haruhiko; Sugihara, Hiroki; Katsume, Hiroshi; Ijichi, Hamao; Okamoto, Kunio; Hosoba, Minoru

    1984-12-01

    Background (BKG) correction is important but debatable in the measurement of Left ventricular ejection fraction (LVEF) with ECG gated blood pool scintigraphy. We devised a new simplified BKG processing (fixed BKG method) without BKG region-of-interest (ROI) assignment, and the accuracy and reproducibility were assessed in 25 patients with various heart diseases and 5 normal subjects by comparison with LVEF obtained by contrast levolgraphy (LVG-EF). Four additional protocols for LVEF measurement with BKG-ROI assignment were also assessed for reference. LVEF calculated using the fixed BKG ratio of 0.64 (BKG count rates were 64%) of end-diastolic count rates of LV) with ''Fixed'' LV-ROI was best correlated with LVG-EF (r = 0.936, p < 0.001) and most approximated (Fixed BKG ratio method EF: 61.1 +- 20.1, LVG-EF: 61.2 +- 20.4% (mean +- SD)) among other protocols. The wide availability of the fixed value of 0.64 was tested in various diseases, body size and end-diastolic volume by LVG, and the results were to be little influenced by them. Furthermore, fixed BKG method produced lower inter-and intra- observer variability than other protocols requiring BKG-ROI assignment, probably due to its simplified processing. In conclusion, fixed BKG ratio method simplifies the measurement of LVEF, and is feasible for automated processing and single probe system.

  2. Smooth quantile normalization.

    Science.gov (United States)

    Hicks, Stephanie C; Okrah, Kwame; Paulson, Joseph N; Quackenbush, John; Irizarry, Rafael A; Bravo, Héctor Corrada

    2018-04-01

    Between-sample normalization is a critical step in genomic data analysis to remove systematic bias and unwanted technical variation in high-throughput data. Global normalization methods are based on the assumption that observed variability in global properties is due to technical reasons and are unrelated to the biology of interest. For example, some methods correct for differences in sequencing read counts by scaling features to have similar median values across samples, but these fail to reduce other forms of unwanted technical variation. Methods such as quantile normalization transform the statistical distributions across samples to be the same and assume global differences in the distribution are induced by only technical variation. However, it remains unclear how to proceed with normalization if these assumptions are violated, for example, if there are global differences in the statistical distributions between biological conditions or groups, and external information, such as negative or control features, is not available. Here, we introduce a generalization of quantile normalization, referred to as smooth quantile normalization (qsmooth), which is based on the assumption that the statistical distribution of each sample should be the same (or have the same distributional shape) within biological groups or conditions, but allowing that they may differ between groups. We illustrate the advantages of our method on several high-throughput datasets with global differences in distributions corresponding to different biological conditions. We also perform a Monte Carlo simulation study to illustrate the bias-variance tradeoff and root mean squared error of qsmooth compared to other global normalization methods. A software implementation is available from https://github.com/stephaniehicks/qsmooth.

  3. Study on simplified estimation of J-integral under thermal loading

    International Nuclear Information System (INIS)

    Takahashi, Y.

    1993-01-01

    For assessing structural integrity or safety of nuclear power plants, strength of structures under the presence of flaws sometimes needs to be evaluated. Because relative large inelastic deformation is anticipated in the liquid metal reactor components even without flaws due to high operating temperature and large temperature gradients, inelastic effects should be properly taken into account in the flaw assessment procedures. It is widely recognized that J-integral and its variations - e.g. fatigue J-integral range and creep J-integral - play substantial roles in the flaw assessment under the presence of large inelastic deformation. Therefore their utilization has been promoted in the recent flaw assessment procedure both for low and high temperature plants. However, it is not very practical to conduct a detailed numerical computation for cracked structures to estimate the values of these parameters for the purpose of trailing crack growth history. Thus development of simplified estimation methods which do not require full numerical calculation for cracked structures is desirable. A method using normalized J-integral solutions tabulated in the handbook is a direct extension of linear fracture mechanics counterpart and it can be used for standard specimen and simple structural configurations subjected to specified loading type. The reference stress method has also been developed but in this case limit load solutions, which are often difficult to obtain for general stress distribution, are necessary instead of nonlinear J-integral solutions. However, both methods have been developed mainly for mechanical loading and thus applying these techniques to thermal stress problem is rather difficult except the cases where the thermal stress can be properly substituted by equivalent mechanical loading as in the case of simple thermal expansion loading. Therefore alternative approach should be pursued for estimating J-integral and their variations in thermal stress problems

  4. A simplified memory network model based on pattern formations

    Science.gov (United States)

    Xu, Kesheng; Zhang, Xiyun; Wang, Chaoqing; Liu, Zonghua

    2014-12-01

    Many experiments have evidenced the transition with different time scales from short-term memory (STM) to long-term memory (LTM) in mammalian brains, while its theoretical understanding is still under debate. To understand its underlying mechanism, it has recently been shown that it is possible to have a long-period rhythmic synchronous firing in a scale-free network, provided the existence of both the high-degree hubs and the loops formed by low-degree nodes. We here present a simplified memory network model to show that the self-sustained synchronous firing can be observed even without these two necessary conditions. This simplified network consists of two loops of coupled excitable neurons with different synaptic conductance and with one node being the sensory neuron to receive an external stimulus signal. This model can be further used to show how the diversity of firing patterns can be selectively formed by varying the signal frequency, duration of the stimulus and network topology, which corresponds to the patterns of STM and LTM with different time scales. A theoretical analysis is presented to explain the underlying mechanism of firing patterns.

  5. Simplified Physics Based Models Research Topical Report on Task #2

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, Srikanta; Ganesh, Priya

    2014-10-31

    We present a simplified-physics based approach, where only the most important physical processes are modeled, to develop and validate simplified predictive models of CO2 sequestration in deep saline formation. The system of interest is a single vertical well injecting supercritical CO2 into a 2-D layered reservoir-caprock system with variable layer permeabilities. We use a set of well-designed full-physics compositional simulations to understand key processes and parameters affecting pressure propagation and buoyant plume migration. Based on these simulations, we have developed correlations for dimensionless injectivity as a function of the slope of fractional-flow curve, variance of layer permeability values, and the nature of vertical permeability arrangement. The same variables, along with a modified gravity number, can be used to develop a correlation for the total storage efficiency within the CO2 plume footprint. Similar correlations are also developed to predict the average pressure within the injection reservoir, and the pressure buildup within the caprock.

  6. On a nonlinear Kalman filter with simplified divided difference approximation

    KAUST Repository

    Luo, Xiaodong; Hoteit, Ibrahim; Moroz, Irene M.

    2012-01-01

    We present a new ensemble-based approach that handles nonlinearity based on a simplified divided difference approximation through Stirling's interpolation formula, which is hence called the simplified divided difference filter (sDDF). The sDDF uses Stirling's interpolation formula to evaluate the statistics of the background ensemble during the prediction step, while at the filtering step the sDDF employs the formulae in an ensemble square root filter (EnSRF) to update the background to the analysis. In this sense, the sDDF is a hybrid of Stirling's interpolation formula and the EnSRF method, while the computational cost of the sDDF is less than that of the EnSRF. Numerical comparison between the sDDF and the EnSRF, with the ensemble transform Kalman filter (ETKF) as the representative, is conducted. The experiment results suggest that the sDDF outperforms the ETKF with a relatively large ensemble size, and thus is a good candidate for data assimilation in systems with moderate dimensions. © 2011 Elsevier B.V. All rights reserved.

  7. Numerical Simulation of Incremental Sheet Forming by Simplified Approach

    Science.gov (United States)

    Delamézière, A.; Yu, Y.; Robert, C.; Ayed, L. Ben; Nouari, M.; Batoz, J. L.

    2011-01-01

    The Incremental Sheet Forming (ISF) is a process, which can transform a flat metal sheet in a 3D complex part using a hemispherical tool. The final geometry of the product is obtained by the relative movement between this tool and the blank. The main advantage of that process is that the cost of the tool is very low compared to deep drawing with rigid tools. The main disadvantage is the very low velocity of the tool and thus the large amount of time to form the part. Classical contact algorithms give good agreement with experimental results, but are time consuming. A Simplified Approach for the contact management between the tool and the blank in ISF is presented here. The general principle of this approach is to imposed displacement of the nodes in contact with the tool at a given position. On a benchmark part, the CPU time of the present Simplified Approach is significantly reduced compared with a classical simulation performed with Abaqus implicit.

  8. On a nonlinear Kalman filter with simplified divided difference approximation

    KAUST Repository

    Luo, Xiaodong

    2012-03-01

    We present a new ensemble-based approach that handles nonlinearity based on a simplified divided difference approximation through Stirling\\'s interpolation formula, which is hence called the simplified divided difference filter (sDDF). The sDDF uses Stirling\\'s interpolation formula to evaluate the statistics of the background ensemble during the prediction step, while at the filtering step the sDDF employs the formulae in an ensemble square root filter (EnSRF) to update the background to the analysis. In this sense, the sDDF is a hybrid of Stirling\\'s interpolation formula and the EnSRF method, while the computational cost of the sDDF is less than that of the EnSRF. Numerical comparison between the sDDF and the EnSRF, with the ensemble transform Kalman filter (ETKF) as the representative, is conducted. The experiment results suggest that the sDDF outperforms the ETKF with a relatively large ensemble size, and thus is a good candidate for data assimilation in systems with moderate dimensions. © 2011 Elsevier B.V. All rights reserved.

  9. MINOS: A simplified Pn solver for core calculation

    International Nuclear Information System (INIS)

    Baudron, A.M.; Lautard, J.J.

    2007-01-01

    This paper describes a new generation of the neutronic core solver MINOS resulting from developments done in the DESCARTES project. For performance reasons, the numerical method of the existing MINOS solver in the SAPHYR system has been reused in the new system. It is based on the mixed-dual finite element approximation of the simplified transport equation. We have extended the previous method to the treatment of unstructured geometries composed by quadrilaterals, allowing us to treat geometries where fuel pins are exactly represented. For Cartesian geometries, the solver takes into account assembly discontinuity coefficients in the simplified P n context. The solver has been rewritten in C + + programming language using an object-oriented design. Its general architecture was reconsidered in order to improve its capability of evolution and its maintainability. Moreover, the performance of the previous version has been improved mainly regarding the matrix construction time; this result improves significantly the performance of the solver in the context of industrial application requiring thermal-hydraulic feedback and depletion calculations. (authors)

  10. Simplified design of flexible expansion anchored plates for nuclear structures

    International Nuclear Information System (INIS)

    Mehta, N.K.; Hingorani, N.V.; Longlais, T.G.; Sargent and Lundy, Chicago, IL)

    1984-01-01

    In nuclear power plant construction, expansion anchored plates are used to support pipe, cable tray and HVAC duct hangers, and various structural elements. The expansion anchored plates provide flexibility in the installation of field-routed lines where cast-in-place embedments are not available. General design requirements for expansion anchored plate assemblies are given in ACI 349, Appendix B (1). The manufacturers recommend installation procedures for their products. Recent field testing in response to NRC Bulletin 79-02 (2) indicates that anchors, installed in accordance with manufacturer's recommended procedures, perform satisfactorily under static and dynamic loading conditions. Finite element analysis is a useful tool to correctly analyze the expansion anchored plates subject to axial tension and biaxial moments, but it becomes expensive and time-consuming to apply this tool for a large number of plates. It is, therefore, advantageous to use a simplified method, even though it may be more conservative as compared to the exact method of analysis. This paper presents a design method referred to as the modified rigid plate analysis approach to simplify both the initial design and the review of as-built conditions

  11. Basic heart examination: feasibility study of first-trimester systematic simplified fetal echocardiography.

    Science.gov (United States)

    Quarello, E; Lafouge, A; Fries, N; Salomon, L J

    2017-02-01

    First-trimester fetal cardiac screening examinations in low-risk populations should not have to meet the specifications required for high-risk populations. Our aim was to evaluate a simplified fetal echocardiographic ('basic heart') examination for early detection of severe congenital heart defects in a low-risk population. This was a first-trimester national 'flash study', performed over a 2-week period. Each observer was requested to perform simplified echocardiography without modifying the time and methods deemed necessary for the routine first-trimester ultrasound examination, in fetuses with crown-rump length between 45 and 84 mm. This basic heart assessment used targeted cross-sections of the four-chamber view (4CV) and of the three vessels and trachea (3VT) view, using color and/or directional power Doppler. All examinations were then reviewed offline and scored for quality by a qualified expert. Sixty observers performed a total of 597 first-trimester ultrasound examinations, each performing an average of 10 (range, 1-26) procedures. Examinations were conducted transabdominally (79%; 472/597), transvaginally (3%; 17/597) or both (18%; 108/597). In 8% (45/597) of cases, the fetal back was anterior, in 18% (108/597) it was on the left side, in 63% (377/597) it was posterior and in 11% (67/597) it was on the right side. It became clear during scoring by the expert that, unlike the Herman quality score for nuchal translucency measurement, it was difficult to assess the quality of these images without taking into account normality of the heart itself. Analysis of scores showed that the 4CV was obtained successfully and was deemed normal in 86% (512/597) of the patients, in 7% (41/597) it was deemed technically infeasible and in 7% (44/597) it was deemed feasible but atypical, which may have been due to the presence of an abnormality or to poor quality of the image. The 3VT view was obtained successfully and was normal in 79% (472/597) of the patients, in 13

  12. Monitoring the normal body

    DEFF Research Database (Denmark)

    Nissen, Nina Konstantin; Holm, Lotte; Baarts, Charlotte

    2015-01-01

    of practices for monitoring their bodies based on different kinds of calculations of weight and body size, observations of body shape, and measurements of bodily firmness. Biometric measurements are familiar to them as are health authorities' recommendations. Despite not belonging to an extreme BMI category...... provides us with knowledge about how to prevent future overweight or obesity. This paper investigates body size ideals and monitoring practices among normal-weight and moderately overweight people. Methods : The study is based on in-depth interviews combined with observations. 24 participants were...... recruited by strategic sampling based on self-reported BMI 18.5-29.9 kg/m2 and socio-demographic factors. Inductive analysis was conducted. Results : Normal-weight and moderately overweight people have clear ideals for their body size. Despite being normal weight or close to this, they construct a variety...

  13. Simplified elastic-plastic analysis of reinforced concrete structures - design method for self-restraining stress

    International Nuclear Information System (INIS)

    Aihara, S.; Atsumi, K.; Ujiie, K.; Satoh, S.

    1981-01-01

    Self-restraining stresses generate not only moments but also axial forces. Therefore the moment and force equilibriums of cross section are considered simultaneously, in combination with other external forces. Thus, under this theory, two computer programs are prepared for. Using these programs, the design procedures which considered the reduction of self-restraining stress, become easy if the elastic design stresses, which are separated normal stresses and self-restraining stresses, are given. Numerical examples are given to illustrate the application of the simplified elastic-plastic analysis and to study its effectiveness. First this method is applied to analyze an upper shielding wall in MARK-2 type's Reactor building. The results are compared with those obtained by the elastic-plastic analysis of Finite Element Method. From this comparison it was confirmed that the method described, had adequate accuracy for re-bar design. As a second example, Mat slab of Reactor building is analyzed. The quantity of re-bars calculated by this method, comes to about two third of re-bars less than those required when self-restraining stress is considered as normal stress. Also, the self-restraining stress reduction factor is about 0.5. (orig./HP)

  14. Turn-based evolution in a simplified model of artistic creative process

    DEFF Research Database (Denmark)

    Dahlstedt, Palle

    2015-01-01

    Evolutionary computation has often been presented as a possible model for creativity in computers. In this paper, evolution is discussed in the light of a theoretical model of human artistic process, recently presented by the author. Some crucial differences between human artistic creativity......, and the results of initial experiments are presented and discussed. Artistic creativity is here modeled as an iterated turn-based process, alternating between a conceptual representation and a material representation of the work-to-be. Evolutionary computation is proposed as a heuristic solution to the principal...... and natural evolution are observed and discussed, also in the light of other creative processes occurring in nature. As a tractable way to overcome these limitations, a new kind of evolutionary implementation of creativity is proposed, based on a simplified version of the previously presented model...

  15. Generalized Safety and Efficacy of Simplified Intravenous Thrombolysis Treatment (SMART) Criteria in Acute Ischemic Stroke

    DEFF Research Database (Denmark)

    Sørensen, Sigrid B; Barazangi, Nobl; Chen, Charlene

    2016-01-01

    BACKGROUND: Common intravenous recombinant tissue plasminogen activator (IV rt-PA) exclusion criteria may substantially limit the use of thrombolysis. Preliminary data have shown that the SMART (Simplified Management of Acute stroke using Revised Treatment) criteria greatly expand patient...... eligibility by reducing thrombolysis exclusions, but they have not been assessed on a large scale. We evaluated the safety and efficacy of general adoption of SMART thrombolysis criteria to a large regional stroke network. METHODS: Retrospective analysis of consecutive patients who received IV thrombolysis...... within a regional stroke network was performed. Patients were divided into those receiving thrombolysis locally versus at an outside hospital. The primary outcome was modified Rankin Scale score (≤1) at discharge and the main safety outcome was symptomatic intracranial hemorrhage (sICH) rate. RESULTS...

  16. The simplified convergence rate calculation for salt grit backfilled caverns in rock salt

    International Nuclear Information System (INIS)

    Navarro, Martin

    2013-03-01

    Within the research and development project 3609R03210 of the German Federal Ministry for the Environment, Nature Conservation and Nuclear Safety, different methods were investigated, which are used for the simplified calculation of convergence rates for mining cavities in salt rock that have been backfilled with crushed salt. The work concentrates on the approach of Stelte and on further developments based on this approach. The work focuses on the physical background of the approaches. Model specific limitations are discussed and possibilities for further development are pointed out. Further on, an alternative approach is presented, which implements independent material laws for the convergence of the mining cavity and the compaction of the crushed salt backfill.

  17. Development of a 2-D Simplified P3 FEM Solver for Arbitrary Geometry Applications

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, Eun Hyun; Joo, Han Gyu [Seoul National University, Seoul (Korea, Republic of)

    2010-10-15

    In the calculation of power distributions and multiplication factors in a nuclear reactor, the Finite Difference Method (FDM) and the nodal methods are primarily used. These methods are, however, limited to particular geometries and lack general application involving arbitrary geometries. The Finite Element Method (FEM) can be employed for arbitrary geometry application and there are numerous FEM codes to solve the neutron diffusion equation or the Sn transport equation. The diffusion based FEM codes have the drawback of inferior accuracy while the Sn based ones require a considerable computing time. This work here is to seek a compromise between these two by employing the simplified P3 (SP3) method for arbitrary geometry applications. Sufficient accuracy with affordable computing time and resources would be achieved with this choice of approximate transport solution when compared to full FEM based Pn or Sn solutions. For now only 2-D solver is considered

  18. Normal modified stable processes

    DEFF Research Database (Denmark)

    Barndorff-Nielsen, Ole Eiler; Shephard, N.

    2002-01-01

    Gaussian (NGIG) laws. The wider framework thus established provides, in particular, for added flexibility in the modelling of the dynamics of financial time series, of importance especially as regards OU based stochastic volatility models for equities. In the special case of the tempered stable OU process......This paper discusses two classes of distributions, and stochastic processes derived from them: modified stable (MS) laws and normal modified stable (NMS) laws. This extends corresponding results for the generalised inverse Gaussian (GIG) and generalised hyperbolic (GH) or normal generalised inverse...

  19. Normalization of satellite imagery

    Science.gov (United States)

    Kim, Hongsuk H.; Elman, Gregory C.

    1990-01-01

    Sets of Thematic Mapper (TM) imagery taken over the Washington, DC metropolitan area during the months of November, March and May were converted into a form of ground reflectance imagery. This conversion was accomplished by adjusting the incident sunlight and view angles and by applying a pixel-by-pixel correction for atmospheric effects. Seasonal color changes of the area can be better observed when such normalization is applied to space imagery taken in time series. In normalized imagery, the grey scale depicts variations in surface reflectance and tonal signature of multi-band color imagery can be directly interpreted for quantitative information of the target.

  20. The normal holonomy group

    International Nuclear Information System (INIS)

    Olmos, C.

    1990-05-01

    The restricted holonomy group of a Riemannian manifold is a compact Lie group and its representation on the tangent space is a product of irreducible representations and a trivial one. Each one of the non-trivial factors is either an orthogonal representation of a connected compact Lie group which acts transitively on the unit sphere or it is the isotropy representation of a single Riemannian symmetric space of rank ≥ 2. We prove that, all these properties are also true for the representation on the normal space of the restricted normal holonomy group of any submanifold of a space of constant curvature. 4 refs

  1. A simplified model for the estimation of energy production of PV systems

    International Nuclear Information System (INIS)

    Aste, Niccolò; Del Pero, Claudio; Leonforte, Fabrizio; Manfren, Massimiliano

    2013-01-01

    The potential of solar energy is far higher than any other renewable source, although several limits exist. In detail the fundamental factors that must be analyzed by investors and policy makers are the cost-effectiveness and the production of PV power plants, respectively, for the decision of investment schemes and energy policy strategies. Tools suitable to be used even by non-specialists, are therefore becoming increasingly important. Many research and development effort have been devoted to this goal in recent years. In this study, a simplified model for PV annual production estimation that can provide results with a level of accuracy comparable with the more sophisticated simulation tools from which it derives is fundamental data. The main advantage of the presented model is that it can be used by virtually anyone, without requiring a specific field expertise. The inherent limits of the model are related to its empirical base, but the methodology presented can be effectively reproduced in the future with a different spectrum of data in order to assess, for example, the effect of technological evolution on the overall performance of PV power generation or establishing performance benchmarks for a much larger variety kinds of PV plants and technologies. - Highlights: • We have analyzed the main methods for estimating the electricity production of photovoltaic systems. • We simulated the same system with two different software in different European locations and estimated the electric production. • We have studied the main losses of a plant PV. • We provide a simplified model to estimate the electrical production of any PV system well designed. • We validated the data obtained by the proposed model with experimental data from three PV systems

  2. The time-dependent simplified P2 equations: Asymptotic analyses and numerical experiments

    International Nuclear Information System (INIS)

    Shin, U.; Miller, W.F. Jr.

    1998-01-01

    Using an asymptotic expansion, the authors found that the modified time-dependent simplified P 2 (SP 2 ) equations are robust, high-order, asymptotic approximations to the time-dependent transport equation in a physical regime in which the conventional time-dependent diffusion equation is the leading-order approximation. Using diffusion limit analysis, they also asymptotically compared three competitive time-dependent equations (the telegrapher's equation, the time-dependent SP 2 equations, and the time-dependent simplified even-parity equation). As a result, they found that the time-dependent SP 2 equations contain higher-order asymptotic approximations to the time-dependent transport equation than the other competitive equations. The numerical results confirm that, in the vast majority of cases, the time-dependent SP 2 solutions are significantly more accurate than the time-dependent diffusion and the telegrapher's solutions. They have also shown that the time-dependent SP 2 equations have excellent characteristics such as rotational invariance (which means no ray effect), good diffusion limit behavior, guaranteed positivity in diffusive regimes, and significant accuracy, even in deep-penetration problems. Through computer-running-time tests, they have shown that the time-dependent SP 2 equations can be solved with significantly less computational effort than the conventionally used, time-dependent S N equations (for N > 2) and almost as fast as the time-dependent diffusion equation. From all these results, they conclude that the time-dependent SP 2 equations should be considered as an important competitor for an improved approximately transport equations solver. Such computationally efficient time-dependent transport models are important for problems requiring enhanced computational efficiency, such as neutronics/fluid-dynamics coupled problems that arise in the analyses of hypothetical nuclear reactor accidents

  3. Simplified dark matter models with charged mediators: prospects for direct detection

    Energy Technology Data Exchange (ETDEWEB)

    Sandick, Pearl; Sinha, Kuver; Teng, Fei [Department of Physics and Astronomy, University of Utah,Salt Lake City, UT 84112 (United States)

    2016-10-05

    We consider direct detection prospects for a class of simplified models of fermionic dark matter (DM) coupled to left and right-handed Standard Model fermions via two charged scalar mediators with arbitrary mixing angle α. DM interactions with the nucleus are mediated by higher electromagnetic moments, which, for Majorana DM, is the anapole moment. After giving a full analytic calculation of the anapole moment, including its α dependence, and matching with limits in the literature, we compute the DM-nucleon scattering cross-section and show the LUX and future LZ constraints on the parameter space of these models. We then compare these results with constraints coming from Fermi-LAT continuum and line searches. Results in the supersymmetric limit of these simplified models are provided in all cases. We find that future direct detection experiments will be able to probe most of the parameter space of these models for O(100−200) GeV DM and lightest mediator mass ≲O(5%) larger than the DM mass. The direct detection prospects dwindle for larger DM mass and larger mass gap between the DM and the lightest mediator mass, although appreciable regions are still probed for O(200) GeV DM and lightest mediator mass ≲O(20%) larger than the DM mass. The direct detection bounds are also attenuated near certain “blind spots' in the parameter space, where the anapole moment is severely suppressed due to cancellation of different terms. We carefully study these blind spots and the associated Fermi-LAT signals in these regions.

  4. Normality in Analytical Psychology

    Directory of Open Access Journals (Sweden)

    Steve Myers

    2013-11-01

    Full Text Available Although C.G. Jung’s interest in normality wavered throughout his career, it was one of the areas he identified in later life as worthy of further research. He began his career using a definition of normality which would have been the target of Foucault’s criticism, had Foucault chosen to review Jung’s work. However, Jung then evolved his thinking to a standpoint that was more aligned to Foucault’s own. Thereafter, the post Jungian concept of normality has remained relatively undeveloped by comparison with psychoanalysis and mainstream psychology. Jung’s disjecta membra on the subject suggest that, in contemporary analytical psychology, too much focus is placed on the process of individuation to the neglect of applications that consider collective processes. Also, there is potential for useful research and development into the nature of conflict between individuals and societies, and how normal people typically develop in relation to the spectrum between individuation and collectivity.

  5. Medically-enhanced normality

    DEFF Research Database (Denmark)

    Møldrup, Claus; Traulsen, Janine Morgall; Almarsdóttir, Anna Birna

    2003-01-01

    Objective: To consider public perspectives on the use of medicines for non-medical purposes, a usage called medically-enhanced normality (MEN). Method: Examples from the literature were combined with empirical data derived from two Danish research projects: a Delphi internet study and a Telebus...

  6. The Normal Fetal Pancreas.

    Science.gov (United States)

    Kivilevitch, Zvi; Achiron, Reuven; Perlman, Sharon; Gilboa, Yinon

    2017-10-01

    The aim of the study was to assess the sonographic feasibility of measuring the fetal pancreas and its normal development throughout pregnancy. We conducted a cross-sectional prospective study between 19 and 36 weeks' gestation. The study included singleton pregnancies with normal pregnancy follow-up. The pancreas circumference was measured. The first 90 cases were tested to assess feasibility. Two hundred ninety-seven fetuses of nondiabetic mothers were recruited during a 3-year period. The overall satisfactory visualization rate was 61.6%. The intraobserver and interobserver variability had high interclass correlation coefficients of of 0.964 and 0.967, respectively. A cubic polynomial regression described best the correlation of pancreas circumference with gestational age (r = 0.744; P pancreas circumference percentiles for each week of gestation were calculated. During the study period, we detected 2 cases with overgrowth syndrome and 1 case with an annular pancreas. In this study, we assessed the feasibility of sonography for measuring the fetal pancreas and established a normal reference range for the fetal pancreas circumference throughout pregnancy. This database can be helpful when investigating fetomaternal disorders that can involve its normal development. © 2017 by the American Institute of Ultrasound in Medicine.

  7. Quantum arrival times and operator normalization

    International Nuclear Information System (INIS)

    Hegerfeldt, Gerhard C.; Seidel, Dirk; Gonzalo Muga, J.

    2003-01-01

    A recent approach to arrival times used the fluorescence of an atom entering a laser illuminated region, and the resulting arrival-time distribution was close to the axiomatic distribution of Kijowski, but not exactly equal, neither in limiting cases nor after compensation of reflection losses by normalization on the level of expectation values. In this paper we employ a normalization on the level of operators, recently proposed in a slightly different context. We show that in this case the axiomatic arrival-time distribution of Kijowski is recovered as a limiting case. In addition, it is shown that Allcock's complex potential model is also a limit of the physically motivated fluorescence approach and connected to Kijowski's distribution through operator normalization

  8. Simplified Methodology to Estimate the Maximum Liquid Helium (LHe) Cryostat Pressure from a Vacuum Jacket Failure

    Science.gov (United States)

    Ungar, Eugene K.; Richards, W. Lance

    2015-01-01

    The aircraft-based Stratospheric Observatory for Infrared Astronomy (SOFIA) is a platform for multiple infrared astronomical observation experiments. These experiments carry sensors cooled to liquid helium temperatures. The liquid helium supply is contained in large (i.e., 10 liters or more) vacuum-insulated dewars. Should the dewar vacuum insulation fail, the inrushing air will condense and freeze on the dewar wall, resulting in a large heat flux on the dewar's contents. The heat flux results in a rise in pressure and the actuation of the dewar pressure relief system. A previous NASA Engineering and Safety Center (NESC) assessment provided recommendations for the wall heat flux that would be expected from a loss of vacuum and detailed an appropriate method to use in calculating the maximum pressure that would occur in a loss of vacuum event. This method involved building a detailed supercritical helium compressible flow thermal/fluid model of the vent stack and exercising the model over the appropriate range of parameters. The experimenters designing science instruments for SOFIA are not experts in compressible supercritical flows and do not generally have access to the thermal/fluid modeling packages that are required to build detailed models of the vent stacks. Therefore, the SOFIA Program engaged the NESC to develop a simplified methodology to estimate the maximum pressure in a liquid helium dewar after the loss of vacuum insulation. The method would allow the university-based science instrument development teams to conservatively determine the cryostat's vent neck sizing during preliminary design of new SOFIA Science Instruments. This report details the development of the simplified method, the method itself, and the limits of its applicability. The simplified methodology provides an estimate of the dewar pressure after a loss of vacuum insulation that can be used for the initial design of the liquid helium dewar vent stacks. However, since it is not an exact

  9. Simplifying the design of microstructured optical fibre pressure sensors.

    Science.gov (United States)

    Osório, Jonas H; Chesini, Giancarlo; Serrão, Valdir A; Franco, Marcos A R; Cordeiro, Cristiano M B

    2017-06-07

    In this paper, we propose a way to simplify the design of microstructured optical fibres with high sensitivity to applied pressure. The use of a capillary fibre with an embedded core allows the exploration of the pressure-induced material birefringence due to the capillary wall displacements and the photoelastic effect. An analytical description of pressure-induced material birefringence is provided, and fibre modal characteristics are explored through numerical simulations. Moreover, a capillary fibre with an embedded core is fabricated and used to probe pressure variations. Even though the embedded-core fibre has a non-optimized structure, measurements showed a pressure sensitivity of (1.04 ± 0.01) nm/bar, which compares well with more complex, specially designed fibre geometries reported in the literature. These results demonstrate that this geometry enables a novel route towards the simplification of microstructured fibre-based pressure sensors.

  10. Development of a simplified urban water balance model (WABILA).

    Science.gov (United States)

    Henrichs, M; Langner, J; Uhl, M

    2016-01-01

    During the last decade, water sensitive urban design (WSUD) has become more and more accepted. However, there is not any simple tool or option available to evaluate the influence of these measures on the local water balance. To counteract the impact of new settlements, planners focus on mitigating increases in runoff through installation of infiltration systems. This leads to an increasing non-natural groundwater recharge and decreased evapotranspiration. Simple software tools which evaluate or simulate the effect of WSUD on the local water balance are still needed. The authors developed a tool named WABILA (Wasserbilanz) that could support planners for optimal WSUD. WABILA is an easy-to-use planning tool that is based on simplified regression functions for established measures and land covers. Results show that WSUD has to be site-specific, based on climate conditions and the natural water balance.

  11. Modeling moisture ingress through simplified concrete crack geometries

    DEFF Research Database (Denmark)

    Pease, Bradley Justin; Michel, Alexander; Geiker, Mette Rica

    2011-01-01

    , considered to have two parts; 1) a coalesced crack length which behaves as a free-surface for moisture ingress, and 2) an isolated microcracking length which resists ingress similarly to the bulk material. Transport model results are compared to experimental results from steel fibre reinforced concrete wedge......This paper introduces a numerical model for ingress in cracked steel fibre reinforced concrete. Details of a simplified crack are preset in the model’s geometry using the cracked hinge model (CHM). The total crack length estimated using the CHM was, based on earlier work on conventional concrete...... on moisture ingress. Results from the transport model indicate the length of the isolated microcracks was approximately 19 mm for the investigated concrete composition....

  12. A simplified computational memory model from information processing

    Science.gov (United States)

    Zhang, Lanhua; Zhang, Dongsheng; Deng, Yuqin; Ding, Xiaoqian; Wang, Yan; Tang, Yiyuan; Sun, Baoliang

    2016-01-01

    This paper is intended to propose a computational model for memory from the view of information processing. The model, called simplified memory information retrieval network (SMIRN), is a bi-modular hierarchical functional memory network by abstracting memory function and simulating memory information processing. At first meta-memory is defined to express the neuron or brain cortices based on the biology and graph theories, and we develop an intra-modular network with the modeling algorithm by mapping the node and edge, and then the bi-modular network is delineated with intra-modular and inter-modular. At last a polynomial retrieval algorithm is introduced. In this paper we simulate the memory phenomena and functions of memorization and strengthening by information processing algorithms. The theoretical analysis and the simulation results show that the model is in accordance with the memory phenomena from information processing view. PMID:27876847

  13. Core concept for long operating cycle simplified BWR (LSBWR)

    International Nuclear Information System (INIS)

    Kouji, Hiraiwa; Noriyuki, Yoshida; Mikihide, Nakamaru; Hideaki, Heki; Masanori, Aritomi

    2002-01-01

    An innovative core concept for a long operating cycle simplified BWR (LSBWR) is currently being developed under a Toshiba Corporation and Tokyo Institute of Technology joint study. In this core concept, the combination of enriched uranium oxide fuels and loose-pitched lattice is adopted for an easy application of natural circulation. A combination of enriched gadolinium and 0.7-times sized small bundle with peripheral-positioned gadolinium rod is also adopted as a key design concept for 15-year cycle operation. Based on three-dimensional nuclear and thermal hydraulic calculation, a nuclear design for fuel bundle has been determined. Core performance has been evaluated based on this bundle design and shows that thermal performance and reactivity characteristics meet core design criteria. Additionally, a control rod operation plan for an extension of control rod life has been successfully determined. (author)

  14. A simplified computational memory model from information processing.

    Science.gov (United States)

    Zhang, Lanhua; Zhang, Dongsheng; Deng, Yuqin; Ding, Xiaoqian; Wang, Yan; Tang, Yiyuan; Sun, Baoliang

    2016-11-23

    This paper is intended to propose a computational model for memory from the view of information processing. The model, called simplified memory information retrieval network (SMIRN), is a bi-modular hierarchical functional memory network by abstracting memory function and simulating memory information processing. At first meta-memory is defined to express the neuron or brain cortices based on the biology and graph theories, and we develop an intra-modular network with the modeling algorithm by mapping the node and edge, and then the bi-modular network is delineated with intra-modular and inter-modular. At last a polynomial retrieval algorithm is introduced. In this paper we simulate the memory phenomena and functions of memorization and strengthening by information processing algorithms. The theoretical analysis and the simulation results show that the model is in accordance with the memory phenomena from information processing view.

  15. Simplified Method for Rapid Purification of Soluble Histones

    Directory of Open Access Journals (Sweden)

    Nives Ivić

    2016-06-01

    Full Text Available Functional and structural studies of histone-chaperone complexes, nucleosome modifications, their interactions with remodelers and regulatory proteins rely on obtaining recombinant histones from bacteria. In the present study, we show that co-expression of Xenopus laevis histone pairs leads to production of soluble H2AH2B heterodimer and (H3H42 heterotetramer. The soluble histone complexes are purified by simple chromatographic techniques. Obtained H2AH2B dimer and H3H4 tetramer are proficient in histone chaperone binding and histone octamer and nucleosome formation. Our optimized protocol enables rapid purification of multiple soluble histone variants with a remarkable high yield and simplifies histone octamer preparation. We expect that this simple approach will contribute to the histone chaperone and chromatin research. This work is licensed under a Creative Commons Attribution 4.0 International License.

  16. A simplified radioimmunoassay of adenosine-3':5'-monophosphate

    International Nuclear Information System (INIS)

    Katoh, Yoshiki; Takezawa, Junichi; Suzuki, Morio; Kuninaka, Akira; Yoshino, Hiroshi

    1975-01-01

    Dextran-coated charcoal was proved to be able to separate free adenosine-3':5'monophosphate (cAMP) from antibody-bound cAMP. Only free cAMO was adsorbed on dextran-coated charcoal within 1 min after contacting the charcoal. In a reaction mixture of cAMP and anti-cAMP-plasma, most of antibody-bound cAMP had not been adsorbed 4 min after contacting. The data obtained were found to be almost the same as the data of another experiment using cellulose ester filter separation technique. Thus, dextran-coated charcoal could be employed to simplify the radioimmunoassay of cAMP. (author)

  17. Simplified vibrocreep buckling analysis of circular cylindrical shells

    International Nuclear Information System (INIS)

    Simeonova, K.; Hadjikov, L.; Georgiev, K.; Iotov, I.

    1981-01-01

    The circular cylindrical shells are used as a mathematical model in the investigation of the reactions of the supporting elements in nuclear reactor core, airplane designing etc. The buckling in the process of vibrocreep is one of the possible catastrophes during the exploitation of those elements. The paper presents a simplified investigation of the vibro-creep stability of a shell axially pressed. The main simplification consists of the fact that the average process of vibro-creep is considered stationary. The modified constitutive equations of Maxwell-Gurevitch-Rabinovitch, concerning elasto-viscous and elasto-plastic material is used. The critical time is calculated after two criteria. Theoretical relations between the critical time and the dynamic loading velocity amplitude are obtained. Those relations are compared to relations experimentally proved. (orig.)

  18. Development of simplified nuclear dry plate measuring system

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Y; Ohta, I [Utsunomiya Univ. (Japan). Faculty of Education; Tezuka, I; Tezuka, T; Makino, K

    1981-08-01

    A simplified nuclear dry plate measuring system was developed. The system consists of a microscope, an ITV camera, a monitor TV, an XY tracker and a micro-computer. The signals of the images of tracks in a nuclear dry plate are sent to the XY tracker, and shown on the monitor TV. The XY tracker displays a pointer on the monitor TV, and makes the output signal of its XY coordinate. This output signal is analyzed by the microcomputer. The software for the measuring process is composed of a program system written in BASIC and the machine language. The data in take, the expansion of the range of measurement and the output of analyzed data are controlled by the program. The accuracy of the measurement of coordinate was studied, and was about 0.39 micrometer for 10 micrometer distance.

  19. Novel simplified hourly energy flow models for photovoltaic power systems

    International Nuclear Information System (INIS)

    Khatib, Tamer; Elmenreich, Wilfried

    2014-01-01

    Highlights: • We developed an energy flow model for standalone PV system using MATLAB line code. • We developed an energy flow model for hybrid PV/wind system using MATLAB line code. • We developed an energy flow model for hybrid PV/diesel system using MATLAB line code. - Abstract: This paper presents simplified energy flow models for photovoltaic (PV) power systems using MATLAB. Three types of PV power system are taken into consideration namely standalone PV systems, hybrid PV/wind systems and hybrid PV/diesel systems. The logic of the energy flow for each PV power system is discussed first and then the MATLAB line codes for these models are provided and explained. The results prove the accuracy of the proposed models. Such models help modeling and sizing PV systems

  20. Cask crush pad analysis using detailed and simplified analysis methods

    International Nuclear Information System (INIS)

    Uldrich, E.D.; Hawkes, B.D.

    1997-01-01

    A crush pad has been designed and analyzed to absorb the kinetic energy of a hypothetically dropped spent nuclear fuel shipping cask into a 44-ft. deep cask unloading pool at the Fluorinel and Storage Facility (FAST). This facility, located at the Idaho Chemical Processing Plant (ICPP) at the Idaho national Engineering and Environmental Laboratory (INEEL), is a US Department of Energy site. The basis for this study is an analysis by Uldrich and Hawkes. The purpose of this analysis was to evaluate various hypothetical cask drop orientations to ensure that the crush pad design was adequate and the cask deceleration at impact was less than 100 g. It is demonstrated herein that a large spent fuel shipping cask, when dropped onto a foam crush pad, can be analyzed by either hand methods or by sophisticated dynamic finite element analysis using computer codes such as ABAQUS. Results from the two methods are compared to evaluate accuracy of the simplified hand analysis approach

  1. Analysis of Turbulent Combustion in Simplified Stratified Charge Conditions

    Science.gov (United States)

    Moriyoshi, Yasuo; Morikawa, Hideaki; Komatsu, Eiji

    The stratified charge combustion system has been widely studied due to the significant potentials for low fuel consumption rate and low exhaust gas emissions. The fuel-air mixture formation process in a direct-injection stratified charge engine is influenced by various parameters, such as atomization, evaporation, and in-cylinder gas motion at high temperature and high pressure conditions. It is difficult to observe the in-cylinder phenomena in such conditions and also challenging to analyze the following stratified charge combustion. Therefore, the combustion phenomena in simplified stratified charge conditions aiming to analyze the fundamental stratified charge combustion are examined. That is, an experimental apparatus which can control the mixture distribution and the gas motion at ignition timing was developed, and the effects of turbulence intensity, mixture concentration distribution, and mixture composition on stratified charge combustion were examined. As a result, the effects of fuel, charge stratification, and turbulence on combustion characteristics were clarified.

  2. Simplified spinal cord phantom for evaluation of SQUID magnetospinography

    International Nuclear Information System (INIS)

    Adachi, Y; Oyama, D; Uehara, G; Somchai, N; Kawabata, S

    2014-01-01

    Spinal cord functional imaging by magnetospinography (MSG) is a noninvasive diagnostic method for spinal cord diseases. However, the accuracy and spatial resolution of lesion localization by MSG have barely been evaluated in detail so far. We developed a simplified spinal cord phantom for MSG evaluation. The spinal cord phantom is composed of a cylindrical vessel filled with saline water, which acts as a model of a neck. A set of modeled vertebrae is arranged in the cylindrical vessel, which has a neural current model made from catheter electrodes. The neural current model emulates the current distribution around the activated site along the axon of the spinal cord nerve. Our MSG system was used to observe the magnetic field from the phantom; a quadrupole-like pattern of the magnetic field distribution, which is a typical distribution pattern for spinal cord magnetic fields, was successfully reproduced by the phantom. Hence, the developed spinal cord phantom can be used to evaluate MSG source analysis methods.

  3. Experimental and numerical investigation of a simplified exhaust model

    Directory of Open Access Journals (Sweden)

    Balázs Vehovszky

    2016-10-01

    Full Text Available A simplified experimental equipment was built to investigate heat radiation and free convection around hot exhaust pipe. Temperatures were measured on the surface of the pipe as like as on heat insulating and -reflecting aluminum shield. Special care was taken to the temperature measuring method: result proved that inappropriate fixing of measuring thermocouples lead to an error of up to 30 % in the temperature-increase values. A detailed 1D numerical model was set up and parametrized so as to the calculation results can be fitted to measured temperature values. In this way thermal properties of the surfaces – as emissivities, absorption coefficients and convective heat transfer coefficients – were determined for temperature sweeps and stationary state cases. The used methods are to be further improved for real automotive parts and higher temperatures.

  4. Simplified model of a PWR primary coolant circuit

    International Nuclear Information System (INIS)

    Souza, A.L. de; Faya, A.J.G.

    1988-01-01

    The computer program RENUR was developed to perform a very simplified simulation of a typical PWR primary circuit. The program has mathematical models for the thermal-hydraulics of the reactor core and the pressurizer, the rest of the circuit being treated as a single volume. Heat conduction in the fuel rod is analysed by a nodal model. Average and hot channels are treated so that the bulk response of the core and DNBR can be evaluated. A Homogenenous model is employed in the pressurizer. Results are presented for a steady-state situation as well as for a loss of load transient. Agreement with the results of more elaborate computer codes is good with substantial reduction in computer costs. (author) [pt

  5. Economical analysis based on a simplified model of micro distillery

    International Nuclear Information System (INIS)

    Bristoti, A.; Adams, R.

    1987-01-01

    The investment costs of the hydrate alcohol distillery as well as the energy balance of its production made inviable its diffusion on a small scale. The present economical analysis is based on a simplified model of micro distillery where the reduction on investment costs in based on technical data based on the possibility of the utilization of an hydrate alcohol with a higher water constant than the usual, i. e. around 85 0 GL. The engineering project of this plant eliminates all pumps, all the liquids (water, sugar cane, syrup and wine) are fed by gravity. The bagasse is considered a noble by-product and it is utilized in poultry industry as a substitute of wood dust. All the heat needs of the micro distillery are supplied by wood. (author)

  6. Inverse correlation between the standard deviation of R-R intervals in supine position and the simplified menopausal index in women with climacteric symptoms.

    Science.gov (United States)

    Yanagihara, Nobuyuki; Seki, Meikan; Nakano, Masahiro; Hachisuga, Toru; Goto, Yukio

    2014-06-01

    Disturbance of autonomic nervous activity has been thought to play a role in the climacteric symptoms of postmenopausal women. This study was therefore designed to investigate the relationship between autonomic nervous activity and climacteric symptoms in postmenopausal Japanese women. The autonomic nervous activity of 40 Japanese women with climacteric symptoms and 40 Japanese women without climacteric symptoms was measured by power spectral analysis of heart rate variability using a standard hexagonal radar chart. The scores for climacteric symptoms were determined using the simplified menopausal index. Sympathetic excitability and irritability, as well as the standard deviation of mean R-R intervals in supine position, were significantly (P standard deviation of mean R-R intervals in supine position and the simplified menopausal index score. The lack of control for potential confounding variables was a limitation of this study. In climacteric women, the standard deviation of mean R-R intervals in supine position is negatively correlated with the simplified menopausal index score.

  7. A new type of simplified fuzzy rule-based system

    Science.gov (United States)

    Angelov, Plamen; Yager, Ronald

    2012-02-01

    Over the last quarter of a century, two types of fuzzy rule-based (FRB) systems dominated, namely Mamdani and Takagi-Sugeno type. They use the same type of scalar fuzzy sets defined per input variable in their antecedent part which are aggregated at the inference stage by t-norms or co-norms representing logical AND/OR operations. In this paper, we propose a significantly simplified alternative to define the antecedent part of FRB systems by data Clouds and density distribution. This new type of FRB systems goes further in the conceptual and computational simplification while preserving the best features (flexibility, modularity, and human intelligibility) of its predecessors. The proposed concept offers alternative non-parametric form of the rules antecedents, which fully reflects the real data distribution and does not require any explicit aggregation operations and scalar membership functions to be imposed. Instead, it derives the fuzzy membership of a particular data sample to a Cloud by the data density distribution of the data associated with that Cloud. Contrast this to the clustering which is parametric data space decomposition/partitioning where the fuzzy membership to a cluster is measured by the distance to the cluster centre/prototype ignoring all the data that form that cluster or approximating their distribution. The proposed new approach takes into account fully and exactly the spatial distribution and similarity of all the real data by proposing an innovative and much simplified form of the antecedent part. In this paper, we provide several numerical examples aiming to illustrate the concept.

  8. Four-jet impingement: Noise characteristics and simplified acoustic model

    International Nuclear Information System (INIS)

    Brehm, C.; Housman, J.A.; Kiris, C.C.; Barad, M.F.; Hutcheson, F.V.

    2017-01-01

    Highlights: • Large eddy simulation of unique four jet impingement configuration. • Characterization of flow features using POD, FFT, and wavelet decomposition. • Noise source identification utilizing causality method. • Development of simplified acoustic model utilizing equivalent source method. • Comparison with experimental data from BENS experiment. - Abstract: The noise generation mechanisms for four directly impinging supersonic jets are investigated employing implicit large eddy simulations with a higher-order weighted essentially non-oscillatory scheme. Although these types of impinging jet configurations have been used in many experiments, a detailed investigation of the noise generation mechanisms has not been conducted before. The flow field is highly complex and contains a wide range of temporal and spatial scales relevant for noise generation. Proper orthogonal decomposition is utilized to characterize the unsteady nature of the flow field involving unsteady shock oscillations, large coherent turbulent flow structures, and the sporadic appearance of vortical flow structures in the center of the four-jet impingement region. The causality method based on Lighthills acoustic analogy is applied to link fluctuations of flow quantities inside the source region to the acoustic pressure in the far field. It will be demonstrated that the entropy fluctuation term plays a vital role in the noise generation process. Consequently, the understanding of the noise generation mechanisms is employed to develop a simplified acoustic model of the four-jet impingement device by utilizing the equivalent source method. Finally, three linear acoustic four-jet impingement models of the four-jet impingement device are used as broadband noise sources inside an engine nacelle and the acoustic scattering results are validated against far-field acoustic experimental data.

  9. Simplified nuclear plant design for tomorrow's energy needs

    International Nuclear Information System (INIS)

    Slember, R.

    1989-09-01

    Commercial nuclear powered plants play an important role in the strategic energy plans of many countries throughout the world. Many energy planners agree that nuclear plants will have to supply an increasing amount of electrical energy in the 1990s and beyond. Just as other major industries are continually taking steps to update and improve existing products, the United States' nuclear industry has embarked on a program to simplify plant systems, shorten construction time and improve economics for new plant models. One of the models being developed by Westinghouse Electric Corporation and Burns and Roe Company is the Advanced Passive 600 MWe design which incorporates safety features that passively protect the reactor during assumed abnormal operating events. These passive safety systems utilize natural circulation/cooling for mitigating abnormal events and simplify plant design and operation. This type of system eliminates the need for costly active safety grade components, results in a reduction of ancillary equipment and assists in shortening construction time. The use of passive safety systems also permits design simplification of the auxiliary systems effectively reducing operating and maintenance requirements. Collectively, the AP600 design features result in a safe plant that addresses and alleviates the critical industry issues that developed in the 1980s. Further, the design addresses utility and regulatory requirements for safety, reliability, maintainability, operations and economics. Program results to date give confidence that the objectives of the Advanced Passive 600 design are achievable through overall plant simplification. The report will include timely results from the work being performed on the salient technical features of the design, plant construction and operation. Other required institutional changes, such as the prerequisite for a design which is complete and licensed prior to start of construction, will also be presented

  10. Simplified PET measurement for evaluating histamine H{sub 1} receptors in human brains using [{sup 11}C]doxepin

    Energy Technology Data Exchange (ETDEWEB)

    Mochizuki, Hideki [Department of Pharmacology, Tohoku University School of Medicine, Sendai, 980-8575 (Japan); Positron Medical Center, Tokyo Metropolitan Institute of Gerontology, Itabashi, Tokyo, 173-0022 (Japan); Kimura, Yuichi [Positron Medical Center, Tokyo Metropolitan Institute of Gerontology, Itabashi, Tokyo, 173-0022 (Japan)]. E-mail: ukimura@ieee.org; Ishii, Kenji [Positron Medical Center, Tokyo Metropolitan Institute of Gerontology, Itabashi, Tokyo, 173-0022 (Japan); Oda, Keiichi [Positron Medical Center, Tokyo Metropolitan Institute of Gerontology, Itabashi, Tokyo, 173-0022 (Japan); Sasaki, Toru [Positron Medical Center, Tokyo Metropolitan Institute of Gerontology, Itabashi, Tokyo, 173-0022 (Japan); Tashiro, Manabu [Department of Pharmacology, Tohoku University School of Medicine, Sendai, 980-8575 (Japan); Yanai, Kazuhiko [Department of Pharmacology, Tohoku University School of Medicine, Sendai, 980-8575 (Japan); Ishiwata, Kiichi [Positron Medical Center, Tokyo Metropolitan Institute of Gerontology, Itabashi, Tokyo, 173-0022 (Japan)

    2004-11-01

    The aim of this study was to develop simplified positron emission tomography measurement using [{sup 11}C]doxepin ([{sup 11}C]DOX) to evaluate histamine H{sub 1} receptors (H1Rs) in human brains. We evaluated the correlation between the distribution volume (DV) of [{sup 11}C]DOX, estimated quantitatively with a two-compartment model, and the [{sup 11}C]DOX uptake obtained at various time intervals and normalized using the metabolite-corrected plasma radioactivity. We found that the static 70- to 90-min images normalized using the plasma radioactivity at 10 min postinjection reflected the DV of [{sup 11}C]DOX-H1R binding.

  11. Idiopathic Normal Pressure Hydrocephalus

    Directory of Open Access Journals (Sweden)

    Basant R. Nassar BS

    2016-04-01

    Full Text Available Idiopathic normal pressure hydrocephalus (iNPH is a potentially reversible neurodegenerative disease commonly characterized by a triad of dementia, gait, and urinary disturbance. Advancements in diagnosis and treatment have aided in properly identifying and improving symptoms in patients. However, a large proportion of iNPH patients remain either undiagnosed or misdiagnosed. Using PubMed search engine of keywords “normal pressure hydrocephalus,” “diagnosis,” “shunt treatment,” “biomarkers,” “gait disturbances,” “cognitive function,” “neuropsychology,” “imaging,” and “pathogenesis,” articles were obtained for this review. The majority of the articles were retrieved from the past 10 years. The purpose of this review article is to aid general practitioners in further understanding current findings on the pathogenesis, diagnosis, and treatment of iNPH.

  12. Normal Weight Dyslipidemia

    DEFF Research Database (Denmark)

    Ipsen, David Hojland; Tveden-Nyborg, Pernille; Lykkesfeldt, Jens

    2016-01-01

    Objective: The liver coordinates lipid metabolism and may play a vital role in the development of dyslipidemia, even in the absence of obesity. Normal weight dyslipidemia (NWD) and patients with nonalcoholic fatty liver disease (NAFLD) who do not have obesity constitute a unique subset...... of individuals characterized by dyslipidemia and metabolic deterioration. This review examined the available literature on the role of the liver in dyslipidemia and the metabolic characteristics of patients with NAFLD who do not have obesity. Methods: PubMed was searched using the following keywords: nonobese......, dyslipidemia, NAFLD, NWD, liver, and metabolically obese/unhealthy normal weight. Additionally, article bibliographies were screened, and relevant citations were retrieved. Studies were excluded if they had not measured relevant biomarkers of dyslipidemia. Results: NWD and NAFLD without obesity share a similar...

  13. Regional and longitudinal estimation of product lifespan distribution: a case study for automobiles and a simplified estimation method.

    Science.gov (United States)

    Oguchi, Masahiro; Fuse, Masaaki

    2015-02-03

    Product lifespan estimates are important information for understanding progress toward sustainable consumption and estimating the stocks and end-of-life flows of products. Publications reported actual lifespan of products; however, quantitative data are still limited for many countries and years. This study presents regional and longitudinal estimation of lifespan distribution of consumer durables, taking passenger cars as an example, and proposes a simplified method for estimating product lifespan distribution. We estimated lifespan distribution parameters for 17 countries based on the age profile of in-use cars. Sensitivity analysis demonstrated that the shape parameter of the lifespan distribution can be replaced by a constant value for all the countries and years. This enabled a simplified estimation that does not require detailed data on the age profile. Applying the simplified method, we estimated the trend in average lifespans of passenger cars from 2000 to 2009 for 20 countries. Average lifespan differed greatly between countries (9-23 years) and was increasing in many countries. This suggests consumer behavior differs greatly among countries and has changed over time, even in developed countries. The results suggest that inappropriate assumptions of average lifespan may cause significant inaccuracy in estimating the stocks and end-of-life flows of products.

  14. Recommended parameters for effect assessment of radioactive airborne effluents under normal condition of nuclear facilities

    International Nuclear Information System (INIS)

    Li Hong; Fang Dong; Sun Chengzhi; Xiao Naihong

    2003-01-01

    A set of models and default parameters are recommended for effect assessment of radioactive airborne effluents under normal condition of nuclear facilities in order to standardize the environmental effect assessment of nuclear facilities, and to simplify the observation and investigation in early phase. The paper introduces the input data and default parameters used in the model

  15. Ethics and "normal birth".

    Science.gov (United States)

    Lyerly, Anne Drapkin

    2012-12-01

    The concept of "normal birth" has been promoted as ideal by several international organizations, although debate about its meaning is ongoing. In this article, I examine the concept of normalcy to explore its ethical implications and raise a trio of concerns. First, in its emphasis on nonuse of technology as a goal, the concept of normalcy may marginalize women for whom medical intervention is necessary or beneficial. Second, in its emphasis on birth as a socially meaningful event, the mantra of normalcy may unintentionally avert attention to meaning in medically complicated births. Third, the emphasis on birth as a normal and healthy event may be a contributor to the long-standing tolerance for the dearth of evidence guiding the treatment of illness during pregnancy and the failure to responsibly and productively engage pregnant women in health research. Given these concerns, it is worth debating not just what "normal birth" means, but whether the term as an ideal earns its keep. © 2012, Copyright the Authors Journal compilation © 2012, Wiley Periodicals, Inc.

  16. Weak limits for quantum random walks

    International Nuclear Information System (INIS)

    Grimmett, Geoffrey; Janson, Svante; Scudo, Petra F.

    2004-01-01

    We formulate and prove a general weak limit theorem for quantum random walks in one and more dimensions. With X n denoting position at time n, we show that X n /n converges weakly as n→∞ to a certain distribution which is absolutely continuous and of bounded support. The proof is rigorous and makes use of Fourier transform methods. This approach simplifies and extends certain preceding derivations valid in one dimension that make use of combinatorial and path integral methods

  17. Can Pediatric Hypertension Criteria Be Simplified? A Prediction Analysis of Subclinical Cardiovascular Outcomes From the Bogalusa Heart Study.

    Science.gov (United States)

    Xi, Bo; Zhang, Tao; Li, Shengxu; Harville, Emily; Bazzano, Lydia; He, Jiang; Chen, Wei

    2017-04-01

    Prehypertension and hypertension in childhood are defined by sex-, age-, and height-specific 90th (or ≥120/80 mm Hg) and 95th percentiles of blood pressure, respectively, by the 2004 Fourth Report. However, these cutoffs are complex and cumbersome for use. This study assessed the performance of a simplified blood pressure definition to predict adult hypertension and subclinical cardiovascular disease. The cohort consisted of 1225 adults (530 men; aged 26.3-47.7 years) from the Bogalusa Heart Study with 27.1-year follow-up since childhood. We used 110/70 and 120/80 mm Hg for children (age, 6-11 years), and 120/80 and 130/85 mm Hg for adolescents (age, 12-17 years) as the simplified definition of childhood prehypertension and hypertension, respectively, to compare with the 2004 Fourth Report (the complex definition). Adult carotid intima-media thickness, pulse wave velocity, and left ventricular mass were measured using digital ultrasound instruments. Compared with normal blood pressure, childhood hypertensives diagnosed by the simplified definition and the complex definition were both at higher risk of adult hypertension with hazard ratio of 3.1 (95% confidence interval, 1.8-5.3) by the simplified definition and 3.2 (2.0-5.0) by the complex definition, high pulse wave velocity with 3.5 (1.7-7.1) and 2.2 (1.2-4.1), high carotid intima-media thickness with 3.1 (1.7-5.6) and 2.0 (1.2-3.6), and left ventricular hypertrophy with 3.4 (1.7-6.8) and 3.0 (1.6-5.6). The results were confirmed by reclassification or receiver operating curve analyses. The simplified childhood blood pressure definition predicts the risk of adult hypertension and subclinical cardiovascular disease equally as the complex definition does, which could be useful for screening hypertensive children to reduce risk of adult cardiovascular disease. © 2017 American Heart Association, Inc.

  18. A coupled remote sensing and simplified surface energy balance approach to estimate actual evapotranspiration from irrigated fields

    Science.gov (United States)

    Senay, G.B.; Budde, Michael; Verdin, J.P.; Melesse, Assefa M.

    2007-01-01

    Accurate crop performance monitoring and production estimation are critical for timely assessment of the food balance of several countries in the world. Since 2001, the Famine Early Warning Systems Network (FEWS NET) has been monitoring crop performance and relative production using satellite-derived data and simulation models in Africa, Central America, and Afghanistan where ground-based monitoring is limited because of a scarcity of weather stations. The commonly used crop monitoring models are based on a crop water-balance algorithm with inputs from satellite-derived rainfall estimates. These models are useful to monitor rainfed agriculture, but they are ineffective for irrigated areas. This study focused on Afghanistan, where over 80 percent of agricultural production comes from irrigated lands. We developed and implemented a Simplified Surface Energy Balance (SSEB) model to monitor and assess the performance of irrigated agriculture in Afghanistan using a combination of 1-km thermal data and 250m Normalized Difference Vegetation Index (NDVI) data, both from the Moderate Resolution Imaging Spectroradiometer (MODIS) sensor. We estimated seasonal actual evapotranspiration (ETa) over a period of six years (2000-2005) for two major irrigated river basins in Afghanistan, the Kabul and the Helmand, by analyzing up to 19 cloud-free thermal and NDVI images from each year. These seasonal ETa estimates were used as relative indicators of year-to-year production magnitude differences. The temporal water-use pattern of the two irrigated basins was indicative of the cropping patterns specific to each region. Our results were comparable to field reports and to estimates based on watershed-wide crop water-balance model results. For example, both methods found that the 2003 seasonal ETa was the highest of all six years. The method also captured water management scenarios where a unique year-to-year variability was identified in addition to water-use differences between

  19. Log-Normal Turbulence Dissipation in Global Ocean Models

    Science.gov (United States)

    Pearson, Brodie; Fox-Kemper, Baylor

    2018-03-01

    Data from turbulent numerical simulations of the global ocean demonstrate that the dissipation of kinetic energy obeys a nearly log-normal distribution even at large horizontal scales O (10 km ) . As the horizontal scales of resolved turbulence are larger than the ocean is deep, the Kolmogorov-Yaglom theory for intermittency in 3D homogeneous, isotropic turbulence cannot apply; instead, the down-scale potential enstrophy cascade of quasigeostrophic turbulence should. Yet, energy dissipation obeys approximate log-normality—robustly across depths, seasons, regions, and subgrid schemes. The distribution parameters, skewness and kurtosis, show small systematic departures from log-normality with depth and subgrid friction schemes. Log-normality suggests that a few high-dissipation locations dominate the integrated energy and enstrophy budgets, which should be taken into account when making inferences from simplified models and inferring global energy budgets from sparse observations.

  20. Watershed wash-off of atmospherically deposited radionuclides: a review of normalized entrainment coefficients

    International Nuclear Information System (INIS)

    Garcia-Sanchez, L.; Konoplev, A.V.

    2009-01-01

    Radionuclide wash-off is the transport of activity by flowing water over the soil surface (runoff). To complete existing reviews on long-term removal rates, this paper focuses on short-term wash-off fluxes, quantified in the literature by soil-runoff transfer factors called normalized liquid and solid entrainment coefficients (noted K l *, K s *). Compiled data concerned essentially 137 Cs and 90 Sr wash-off measured under simulated rainfalls on small experimental plots after Chernobyl fallout in the exclusion zone. K l * and K s * values span approximately one order of magnitude. Their validity is limited to a season, and their representativeness is limited by restricted studied situations, notably dominant unsoluble forms in fallout, light soils and intense rainfalls. Formulas based on a simplified representation of the soil-runoff system were proposed to generalize the existing values for other conditions. However, their implementation requires a more systematic compilation of the available information, including decisive influence factors such as the fraction of exchangeable form, distribution coefficient, suspended matter enrichment ratio. Entrainment coefficients K l * and K s * were mathematically related to the transfer function approach. The proposed relationships proved their complementarity in terms of time support and captured fluctuations. Both approaches should be used in assessments to estimate average fluxes and their variability.

  1. Simplified models of vector control impact upon malaria transmission by zoophagic mosquitoes.

    Directory of Open Access Journals (Sweden)

    Samson S Kiware

    Full Text Available BACKGROUND: High coverage of personal protection measures that kill mosquitoes dramatically reduce malaria transmission where vector populations depend upon human blood. However, most primary malaria vectors outside of sub-Saharan Africa can be classified as "very zoophagic," meaning they feed occasionally (<10% of blood meals upon humans, so personal protection interventions have negligible impact upon their survival. METHODS AND FINDINGS: We extended a published malaria transmission model to examine the relationship between transmission, control, and the baseline proportion of bloodmeals obtained from humans (human blood index. The lower limit of the human blood index enables derivation of simplified models for zoophagic vectors that (1 Rely on only three field-measurable parameters. (2 Predict immediate and delayed (with and without assuming reduced human infectivity, respectively impacts of personal protection measures upon transmission. (3 Illustrate how appreciable indirect communal-level protection for non-users can be accrued through direct personal protection of users. (4 Suggest the coverage and efficacy thresholds required to attain epidemiological impact. The findings suggest that immediate, indirect, community-wide protection of users and non-users alike may linearly relate to the efficacy of a user's direct personal protection, regardless of whether that is achieved by killing or repelling mosquitoes. High protective coverage and efficacy (≥80% are important to achieve epidemiologically meaningful impact. Non-users are indirectly protected because the two most common species of human malaria are strict anthroponoses. Therefore, the small proportion of mosquitoes that are killed or diverted while attacking humans can represent a large proportion of those actually transmitting malaria. CONCLUSIONS: Simplified models of malaria transmission by very zoophagic vectors may be used by control practitioners to predict intervention impact

  2. Accounting for uncertain fault geometry in earthquake source inversions - I: theory and simplified application

    Science.gov (United States)

    Ragon, Théa; Sladen, Anthony; Simons, Mark

    2018-05-01

    The ill-posed nature of earthquake source estimation derives from several factors including the quality and quantity of available observations and the fidelity of our forward theory. Observational errors are usually accounted for in the inversion process. Epistemic errors, which stem from our simplified description of the forward problem, are rarely dealt with despite their potential to bias the estimate of a source model. In this study, we explore the impact of uncertainties related to the choice of a fault geometry in source inversion problems. The geometry of a fault structure is generally reduced to a set of parameters, such as position, strike and dip, for one or a few planar fault segments. While some of these parameters can be solved for, more often they are fixed to an uncertain value. We propose a practical framework to address this limitation by following a previously implemented method exploring the impact of uncertainties on the elastic properties of our models. We develop a sensitivity analysis to small perturbations of fault dip and position. The uncertainties in fault geometry are included in the inverse problem under the formulation of the misfit covariance matrix that combines both prediction and observation uncertainties. We validate this approach with the simplified case of a fault that extends infinitely along strike, using both Bayesian and optimization formulations of a static inversion. If epistemic errors are ignored, predictions are overconfident in the data and source parameters are not reliably estimated. In contrast, inclusion of uncertainties in fault geometry allows us to infer a robust posterior source model. Epistemic uncertainties can be many orders of magnitude larger than observational errors for great earthquakes (Mw > 8). Not accounting for uncertainties in fault geometry may partly explain observed shallow slip deficits for continental earthquakes. Similarly, ignoring the impact of epistemic errors can also bias estimates of

  3. Center manifolds, normal forms and bifurcations of vector fields with application to coupling between periodic and steady motions

    Science.gov (United States)

    Holmes, Philip J.

    1981-06-01

    We study the instabilities known to aeronautical engineers as flutter and divergence. Mathematically, these states correspond to bifurcations to limit cycles and multiple equilibrium points in a differential equation. Making use of the center manifold and normal form theorems, we concentrate on the situation in which flutter and divergence become coupled, and show that there are essentially two ways in which this is likely to occur. In the first case the system can be reduced to an essential model which takes the form of a single degree of freedom nonlinear oscillator. This system, which may be analyzed by conventional phase-plane techniques, captures all the qualitative features of the full system. We discuss the reduction and show how the nonlinear terms may be simplified and put into normal form. Invariant manifold theory and the normal form theorem play a major role in this work and this paper serves as an introduction to their application in mechanics. Repeating the approach in the second case, we show that the essential model is now three dimensional and that far more complex behavior is possible, including nonperiodic and ‘chaotic’ motions. Throughout, we take a two degree of freedom system as an example, but the general methods are applicable to multi- and even infinite degree of freedom problems.

  4. Penrose limits and RG flows

    International Nuclear Information System (INIS)

    Gimon, Eric G.; Sonnenschein, Jacob; Pando Zayas, Leopoldo A.

    2002-01-01

    The Penrose-Gueven limit simplifies a given supergravity solution into a pp-wave background. Aiming at clarifying its relation to renormalization group flow we study the Penrose-Guven limit of supergravity backgrounds that are dual to non-conformal gauge theories. The resulting backgrounds fall in a class simple enough that the quantum particle is exactly solvable. We propose a map between the effective time-dependent quantum mechanical problem and the RG flow in the gauge theory. As a testing ground we consider explicitly two Penrose limits of the infrared fixed point of the Pilch-Warner solution. We analyze the corresponding gauge theory picture and write down the operators which are the duals of the low lying string states. We also address RG flows of a different nature by considering the Penrose-Gueven limit of a stack of N D p branes. We note that in the far IR (for p<3)the limit generically has negative mass-squared. This phenomenon signals, in the world sheet picture, the necessity to transform to another description. In this regard, we consider explicitly the cases of M2 from D2 and F1 from D1. (author)

  5. Gbm.auto: A software tool to simplify spatial modelling and Marine Protected Area planning

    Science.gov (United States)

    Officer, Rick; Clarke, Maurice; Reid, David G.; Brophy, Deirdre

    2017-01-01

    Boosted Regression Trees. Excellent for data-poor spatial management but hard to use Marine resource managers and scientists often advocate spatial approaches to manage data-poor species. Existing spatial prediction and management techniques are either insufficiently robust, struggle with sparse input data, or make suboptimal use of multiple explanatory variables. Boosted Regression Trees feature excellent performance and are well suited to modelling the distribution of data-limited species, but are extremely complicated and time-consuming to learn and use, hindering access for a wide potential user base and therefore limiting uptake and usage. BRTs automated and simplified for accessible general use with rich feature set We have built a software suite in R which integrates pre-existing functions with new tailor-made functions to automate the processing and predictive mapping of species abundance data: by automating and greatly simplifying Boosted Regression Tree spatial modelling, the gbm.auto R package suite makes this powerful statistical modelling technique more accessible to potential users in the ecological and modelling communities. The package and its documentation allow the user to generate maps of predicted abundance, visualise the representativeness of those abundance maps and to plot the relative influence of explanatory variables and their relationship to the response variables. Databases of the processed model objects and a report explaining all the steps taken within the model are also generated. The package includes a previously unavailable Decision Support Tool which combines estimated escapement biomass (the percentage of an exploited population which must be retained each year to conserve it) with the predicted abundance maps to generate maps showing the location and size of habitat that should be protected to conserve the target stocks (candidate MPAs), based on stakeholder priorities, such as the minimisation of fishing effort displacement. Gbm

  6. Simplified procedures for fast reactor fuel cycle and sensitivity analysis

    International Nuclear Information System (INIS)

    Badruzzaman, A.

    1979-01-01

    The Continuous Slowing Down-Integral Transport Theory has been extended to perform criticality calculations in a Fast Reactor Core-blanket system achieving excellent prediction of the spectrum and the eigenvalue. The integral transport parameters did not need recalculation with source iteration and were found to be relatively constant with exposure. Fuel cycle parameters were accurately predicted when these were not varied, thus reducing a principal potential penalty of the Intergal Transport approach where considerable effort may be required to calculate transport parameters in more complicated geometries. The small variation of the spectrum in the central core region, and its weak dependence on exposure for both this region, the core blanket interface and blanket region led to the extension and development of inexpensive simplified procedures to complement exact methods. These procedures gave accurate predictions of the key fuel cycle parameters such as cost and their sensitivity to variation in spectrum-averaged and multigroup cross sections. They also predicted the implications of design variation on these parameters very well. The accuracy of these procedures and their use in analyzing a wide variety of sensitivities demonstrate the potential utility of survey calculations in Fast Reactor analysis and fuel management

  7. CONTROLLABILITY OF TRADITIONAL NEIGHBORHOOD AND ITS SIMPLIFIED LAYOUT

    Directory of Open Access Journals (Sweden)

    M. Salim Ferwati

    2010-03-01

    Full Text Available Street hierarchy, as a way of presenting intended information, conforms to social rules that underlay architectural and urban designs to create public, semi-public, and semi-private. These social rules have the responsibility to convey necessary information about place to outsiders as well as to insiders. This research looks at urban spaces as physical structures that represent foci of attention of users and that are collectively a part of the social pattern framework. The argument of this study is that connectivity and forms of streets house certain social rules that intended to serve users, so that any changes in the street layout lead to changes in its social rules. As a case study, the complexity of a walled Arab neighborhood was examined through Sur Lawatyia, located in Muscat Governorate, Oman. By replacing the curvilinear and broken streets of this neighborhood with straight ones; a simplified street layout was derived. Then, a comparison of both street layouts was carried out through mapping, tabulation, charts, correlation test, and with reliance on the method of measurement of street control values introduced by Hillier and Hanson in 1984. The result was that the simple form is far short to be the representation of the space syntax of the traditional street layout.

  8. Simplified hearing protector ratings—an international comparison

    Science.gov (United States)

    Waugh, R.

    1984-03-01

    A computer was programmed to model the distributions of dB(A) levels reaching the ears of an imaginary workforce wearing hearing protectors selected on the basis of either octave band attenuation values or various simplified ratings in use in Australia, Germany, Poland, Spain or the U.S.A. Both multi-valued and single-valued versions of dB(A) reduction and sound level conversion ratings were considered. Ratings were compared in terms of precision and protection rate and the comparisons were replicated for different samples of noise spectra ( N = 400) and hearing protectors ( N = 70) to establish the generality of the conclusions. Different countries adopt different approaches to the measurement of octave band attenuation values and the consequences of these differences were investigated. All rating systems have built-in correction factors to account for hearing protector performance variability and the merits of these were determined in the light of their ultimate effects on the distribution of dB(A) levels reaching wearers' ears. It was concluded that the optimum rating is one that enables the dB(A) level reaching wearers to be estimated by subtracting a single rating value from the dB(C) level of the noise environment, the rating value to be determined for a pink noise spectrum from mean minus one standard deviation octave band attenuation values with further protection rate adjustments being achieved by the use of a constant correction factor.

  9. A Simplified Supercritical Fast Reactor with Thorium Fuel

    Directory of Open Access Journals (Sweden)

    Peng Zhang

    2014-01-01

    Full Text Available Super-Critical water-cooled Fast Reactor (SCFR is a feasible option for the Gen-IV SCWR designs, in which much less moderator and thus coolant are needed for transferring the fission heat from the core compared with the traditional LWRs. The fast spectrum of SCFR is useful for fuel breeding and thorium utilization, which is then beneficial for enhancing the sustainability of the nuclear fuel cycle. A SCFR core is constructed in this work, with the aim of simplifying the mechanical structure and keeping negative coolant void reactivity during the whole core life. A core burnup simulation scheme based on Monte Carlo lattice homogenization is adopted in this study, and the reactor physics analysis has been performed with DU-MOX and Th-MOX fuel. The main issues discussed include the fuel conversion ratio and the coolant void reactivity. The analysis shows that thorium-based fuel can provide inherent safety for SCFR without use of blanket, which is favorable for the mechanical design of SCFR.

  10. A simplified study of trans-mitral Doppler patterns

    Directory of Open Access Journals (Sweden)

    Thomas George

    2008-11-01

    Full Text Available Abstract Background Trans-mitral Doppler produces complex patterns with a great deal of variability. There are several confusing numerical measures and indices to study these patterns. However trans-mitral Doppler produces readymade data visualization by pattern generation which could be interpreted by pattern analysis. By following a systematic approach we could create an order and use this tool to study cardiac function. Presentation of the hypothesis In this new approach we eliminate the variables and apply pattern recognition as the main criterion of study. Proper terminologies are also devised to avoid confusion. In this way we can get some meaningful information. Testing the hypothesis Trans-mitral Doppler should be seen as patterns rather than the amplitude. The hypothesis can be proven by logical deduction, extrapolation and elimination of variables. Trans-mitral flow is also analyzed vis-à-vis the Starling's Law applied to the left atrium. Implications of the hypothesis Trans-mitral Doppler patterns are not just useful for evaluating diastolic function. They are also useful to evaluate systolic function. By following this schema we could get useful diagnostic information and therapeutic options using simple pattern recognition with minimal measurements. This simplified but practical approach will be useful in day to day clinical practice and help in understanding cardiac function better. This will also standardize research and improve communication.

  11. Simplified Modeling of Tropospheric Ozone Formation Considering Alternative Fuels Using

    Directory of Open Access Journals (Sweden)

    Leonardo Aragão Ferreira da Silva

    2014-07-01

    Full Text Available Brazilian cities have been constantly exposed to air quality episodes of high ozone concentrations (O3 . Known for not be emitted directly into the environment, O3 is a result of several chemical reactions of other pollutants emitted to atmosphere. The growth of vehicle fleet and government incentives for using alternative fuels like ethanol and Compressed Natural Gas (CNG are changing the Brazilian Metropolitan Areas in terms of acetaldehyde and formaldehyde emissions, Volatile Organic Compounds (VOC's present in the atmosphere and known to act on the kinetics of ozone. Driven by high concentrations of tropospheric ozone in urban/industry centers and its implications for environment and population health, the target of this work is understand the kinetics of ozone formation through the creation of a mathematical model in FORTRAN 90, describing a system of coupled ordinary differential equations able to represent a simplified mechanism of photochemical reactions in the Brazilian Metropolitan Area. Evaluating the concentration results of each pollutant were possible to observe the precursor’s influence on tropospheric ozone formation, which seasons were more conducive to this one and which are the influences of weather conditions on formation of photochemical smog.

  12. Impact of mass generation for spin-1 mediator simplified models

    International Nuclear Information System (INIS)

    Bell, Nicole F.; Cai, Yi; Leane, Rebecca K.

    2017-01-01

    In the simplified dark matter models commonly studied, the mass generation mechanism for the dark fields is not typically specified. We demonstrate that the dark matter interaction types, and hence the annihilation processes relevant for relic density and indirect detection, are strongly dictated by the mass generation mechanism chosen for the dark sector particles, and the requirement of gauge invariance. We focus on the class of models in which fermionic dark matter couples to a spin-1 vector or axial-vector mediator. However, in order to generate dark sector mass terms, it is necessary in most cases to introduce a dark Higgs field and thus a spin-0 scalar mediator will also be present. In the case that all the dark sector fields gain masses via coupling to a single dark sector Higgs field, it is mandatory that the axial-vector coupling of the spin-1 mediator to the dark matter is non-zero; the vector coupling may also be present depending on the charge assignments. For all other mass generation options, only pure vector couplings between the spin-1 mediator and the dark matter are allowed. If these coupling restrictions are not obeyed, unphysical results may be obtained such as a violation of unitarity at high energies. These two-mediator scenarios lead to important phenomenology that does not arise in single mediator models. We survey two-mediator dark matter models which contain both vector and scalar mediators, and explore their relic density and indirect detection phenomenology.

  13. Development of simplified decommissioning cost estimation code for nuclear facilities

    International Nuclear Information System (INIS)

    Tachibana, Mitsuo; Shiraishi, Kunio; Ishigami, Tsutomu

    2010-01-01

    The simplified decommissioning cost estimation code for nuclear facilities (DECOST code) was developed in consideration of features and structures of nuclear facilities and similarity of dismantling methods. The DECOST code could calculate 8 evaluation items of decommissioning cost. Actual dismantling in the Japan Atomic Energy Agency (JAEA) was evaluated; unit conversion factors used to calculate the manpower of dismantling activities were evaluated. Consequently, unit conversion factors of general components could be classified into three kinds. Weights of components and structures of the facility were necessary for calculation of manpower. Methods for evaluating weights of components and structures of the facility were studied. Consequently, the weight of components in the facility was proportional to the weight of structures of the facility. The weight of structures of the facility was proportional to the total area of floors in the facility. Decommissioning costs of 7 nuclear facilities in the JAEA were calculated by using the DECOST code. To verify the calculated results, the calculated manpower was compared with the manpower gained from actual dismantling. Consequently, the calculated manpower and actual manpower were almost equal. The outline of the DECOST code, evaluation results of unit conversion factors, the evaluation method of the weights of components and structures of the facility are described in this report. (author)

  14. Discrimination of musical instrument sounds resynthesized with simplified spectrotemporal parameters.

    Science.gov (United States)

    McAdams, S; Beauchamp, J W; Meneguzzi, S

    1999-02-01

    The perceptual salience of several outstanding features of quasiharmonic, time-variant spectra was investigated in musical instrument sounds. Spectral analyses of sounds from seven musical instruments (clarinet, flute, oboe, trumpet, violin, harpsichord, and marimba) produced time-varying harmonic amplitude and frequency data. Six basic data simplifications and five combinations of them were applied to the reference tones: amplitude-variation smoothing, coherent variation of amplitudes over time, spectral-envelope smoothing, forced harmonic-frequency variation, frequency-variation smoothing, and harmonic-frequency flattening. Listeners were asked to discriminate sounds resynthesized with simplified data from reference sounds resynthesized with the full data. Averaged over the seven instruments, the discrimination was very good for spectral envelope smoothing and amplitude envelope coherence, but was moderate to poor in decreasing order for forced harmonic frequency variation, frequency variation smoothing, frequency flattening, and amplitude variation smoothing. Discrimination of combinations of simplifications was equivalent to that of the most potent constituent simplification. Objective measurements were made on the spectral data for harmonic amplitude, harmonic frequency, and spectral centroid changes resulting from simplifications. These measures were found to correlate well with discrimination results, indicating that listeners have access to a relatively fine-grained sensory representation of musical instrument sounds.

  15. Aerodynamic drag control by pulsed jets on simplified car geometry

    Science.gov (United States)

    Gilliéron, Patrick; Kourta, Azeddine

    2013-02-01

    Aerodynamic drag control by pulsed jets is tested in a wind tunnel around a simplified car geometry named Ahmed body with a rear slant angle of 35°. Pulsed jet actuators are located 5 × 10-3 m from the top of the rear window. These actuators are produced by a pressure difference ranging from 1.5 to 6.5 × 105 Pa. Their excitation frequency can vary between 10 and 550 Hz. The analysis of the control effects is based on wall visualizations, aerodynamic drag coefficient measurements, and the velocity fields obtained by 2D PIV measurements. The maximum drag reduction is 20 % and is obtained for the excitation frequency F j = 500 Hz and for the pressure difference ∆ P = 1.5 × 105 Pa. This result is linked with a substantial reduction in the transverse development of the longitudinal vortex structures coming from the left and right lateral sides of the rear window, with a displacement of the vortex centers downstream and with a decrease in the transverse rotational absolute values of these structures.

  16. SHEAN (Simplified Human Error Analysis code) and automated THERP

    International Nuclear Information System (INIS)

    Wilson, J.R.

    1993-01-01

    One of the most widely used human error analysis tools is THERP (Technique for Human Error Rate Prediction). Unfortunately, this tool has disadvantages. The Nuclear Regulatory Commission, realizing these drawbacks, commissioned Dr. Swain, the author of THERP, to create a simpler, more consistent tool for deriving human error rates. That effort produced the Accident Sequence Evaluation Program Human Reliability Analysis Procedure (ASEP), which is more conservative than THERP, but a valuable screening tool. ASEP involves answering simple questions about the scenario in question, and then looking up the appropriate human error rate in the indicated table (THERP also uses look-up tables, but four times as many). The advantages of ASEP are that human factors expertise is not required, and the training to use the method is minimal. Although not originally envisioned by Dr. Swain, the ASEP approach actually begs to be computerized. That WINCO did, calling the code SHEAN, for Simplified Human Error ANalysis. The code was done in TURBO Basic for IBM or IBM-compatible MS-DOS, for fast execution. WINCO is now in the process of comparing this code against THERP for various scenarios. This report provides a discussion of SHEAN

  17. Simplifying the Development, Use and Sustainability of HPC Software

    Directory of Open Access Journals (Sweden)

    Jeremy Cohen

    2014-07-01

    Full Text Available Developing software to undertake complex, compute-intensive scientific processes requires a challenging combination of both specialist domain knowledge and software development skills to convert this knowledge into efficient code. As computational platforms become increasingly heterogeneous and newer types of platform such as Infrastructure-as-a-Service (IaaS cloud computing become more widely accepted for high-performance computing (HPC, scientists require more support from computer scientists and resource providers to develop efficient code that offers long-term sustainability and makes optimal use of the resources available to them. As part of the libhpc stage 1 and 2 projects we are developing a framework to provide a richer means of job specification and efficient execution of complex scientific software on heterogeneous infrastructure. In this updated version of our submission to the WSSSPE13 workshop at SuperComputing 2013 we set out our approach to simplifying access to HPC applications and resources for end-users through the use of flexible and interchangeable software components and associated high-level functional-style operations. We believe this approach can support sustainability of scientific software and help to widen access to it.

  18. Simplified two and three dimensional HTTR benchmark problems

    International Nuclear Information System (INIS)

    Zhang Zhan; Rahnema, Farzad; Zhang Dingkang; Pounders, Justin M.; Ougouag, Abderrafi M.

    2011-01-01

    To assess the accuracy of diffusion or transport methods for reactor calculations, it is desirable to create heterogeneous benchmark problems that are typical of whole core configurations. In this paper we have created two and three dimensional numerical benchmark problems typical of high temperature gas cooled prismatic cores. Additionally, a single cell and single block benchmark problems are also included. These problems were derived from the HTTR start-up experiment. Since the primary utility of the benchmark problems is in code-to-code verification, minor details regarding geometry and material specification of the original experiment have been simplified while retaining the heterogeneity and the major physics properties of the core from a neutronics viewpoint. A six-group material (macroscopic) cross section library has been generated for the benchmark problems using the lattice depletion code HELIOS. Using this library, Monte Carlo solutions are presented for three configurations (all-rods-in, partially-controlled and all-rods-out) for both the 2D and 3D problems. These solutions include the core eigenvalues, the block (assembly) averaged fission densities, local peaking factors, the absorption densities in the burnable poison and control rods, and pin fission density distribution for selected blocks. Also included are the solutions for the single cell and single block problems.

  19. A simplified model for TIG-dressing numerical simulation

    Science.gov (United States)

    Ferro, P.; Berto, F.; James, M. N.

    2017-04-01

    Irrespective of the mechanical properties of the alloy to be welded, the fatigue strength of welded joints is primarily controlled by the stress concentration associated with the weld toe or weld root. In order to reduce the effects of such notch defects in welds, which are influenced by tensile properties of the alloy, post-weld improvement techniques have been developed. The two most commonly used techniques are weld toe grinding and TIG dressing, which are intended to both remove toe defects such as non-metallic intrusions and to re-profile the weld toe region to give a lower stress concentration. In the case of TIG dressing the weld toe is re-melted to provide a smoother transition between the plate and the weld crown and to beneficially modify the residual stress redistribution. Assessing the changes to weld stress state arising from TIG-dressing is most easily accomplished through a complex numerical simulation that requires coupled thermo-fluid dynamics and solid mechanics. However, this can be expensive in terms of computational cost and time needed to reach a solution. The present paper therefore proposes a simplified numerical model that overcomes such drawbacks and which simulates the remelted toe region by means of the activation and deactivation of elements in the numerical model.

  20. Simplified Thermo-Chemical Modelling For Hypersonic Flow

    Science.gov (United States)

    Sancho, Jorge; Alvarez, Paula; Gonzalez, Ezequiel; Rodriguez, Manuel

    2011-05-01

    Hypersonic flows are connected with high temperatures, generally associated with strong shock waves that appear in such flows. At high temperatures vibrational degrees of freedom of the molecules may become excited, the molecules may dissociate into atoms, the molecules or free atoms may ionize, and molecular or ionic species, unimportant at lower temperatures, may be formed. In order to take into account these effects, a chemical model is needed, but this model should be simplified in order to be handled by a CFD code, but with a sufficient precision to take into account the physics more important. This work is related to a chemical non-equilibrium model validation, implemented into a commercial CFD code, in order to obtain the flow field around bodies in hypersonic flow. The selected non-equilibrium model is composed of seven species and six direct reactions together with their inverse. The commercial CFD code where the non- equilibrium model has been implemented is FLUENT. For the validation, the X38/Sphynx Mach 20 case is rebuilt on a reduced geometry, including the 1/3 Lref forebody. This case has been run in laminar regime, non catalytic wall and with radiative equilibrium wall temperature. The validated non-equilibrium model is applied to the EXPERT (European Experimental Re-entry Test-bed) vehicle at a specified trajectory point (Mach number 14). This case has been run also in laminar regime, non catalytic wall and with radiative equilibrium wall temperature.

  1. Synthesis of cationic star polymers by simplified electrochemically mediated ATRP

    Directory of Open Access Journals (Sweden)

    P. Chmielarz

    2016-10-01

    Full Text Available Cyclodextrin-based cationic star polymers were synthesized using β-cyclodextrin (β-CD core, and 2-(dimethylamino ethyl methacrylate (DMAEMA as hydrophilic arms. Star-shaped polymers were prepared via a simplified electrochemically mediated ATRP (seATRP under potentiostatic and galvanostatic conditions. The polymerization results showed molecular weight (MW evolution close to theoretical values, and maintained narrow molecular weight distribution (MWD of obtained stars. The rate of the polymerizations was controlled by applying more positive potential values thereby suppressing star-star coupling reactions. Successful chain extension of the ω-functional arms with a hydrophobic n-butyl acrylate (BA formed star block copolymers and confirmed the living nature of the β-CD-PDMAEMA star polymers prepared by seATRP. Novelty of this work is that the β-CD-PDMAEMA-b-PBA cationic star block copolymers were synthesized for the first time via seATRP procedure, utilizing only 40 ppm of catalyst complex. The results from 1H NMR spectral studies support the formation of cationic star (copolymers.

  2. A simplified Suomi NPP VIIRS dust detection algorithm

    Science.gov (United States)

    Yang, Yikun; Sun, Lin; Zhu, Jinshan; Wei, Jing; Su, Qinghua; Sun, Wenxiao; Liu, Fangwei; Shu, Meiyan

    2017-11-01

    Due to the complex characteristics of dust and sparse ground-based monitoring stations, dust monitoring is facing severe challenges, especially in dust storm-prone areas. Aim at constructing a high-precision dust storm detection model, a pixel database, consisted of dusts over a variety of typical feature types such as cloud, vegetation, Gobi and ice/snow, was constructed, and their distributions of reflectance and Brightness Temperatures (BT) were analysed, based on which, a new Simplified Dust Detection Algorithm (SDDA) for the Suomi National Polar-Orbiting Partnership Visible infrared Imaging Radiometer (NPP VIIRS) is proposed. NPP VIIRS images covering the northern China and Mongolian regions, where features serious dust storms, were selected to perform the dust detection experiments. The monitoring results were compared with the true colour composite images, and results showed that most of the dust areas can be accurately detected, except for fragmented thin dusts over bright surfaces. The dust ground-based measurements obtained from the Meteorological Information Comprehensive Analysis and Process System (MICAPS) and the Ozone Monitoring Instrument Aerosol Index (OMI AI) products were selected for comparison purposes. Results showed that the dust monitoring results agreed well in the spatial distribution with OMI AI dust products and the MICAPS ground-measured data with an average high accuracy of 83.10%. The SDDA is relatively robust and can realize automatic monitoring for dust storms.

  3. Cyclosporin safety in a simplified rat brain tumor implantation model

    Directory of Open Access Journals (Sweden)

    Francisco H. C. Felix

    2012-01-01

    Full Text Available Brain cancer is the second neurological cause of death. A simplified animal brain tumor model using W256 (carcinoma 256, Walker cell line was developed to permit the testing of novel treatment modalities. Wistar rats had a cell tumor solution inoculated stereotactically in the basal ganglia (right subfrontal caudate. This model yielded tumor growth in 95% of the animals, and showed absence of extracranial metastasis and systemic infection. Survival median was 10 days. Estimated tumor volume was 17.08±6.7 mm³ on the 7th day and 67.25±19.8 mm³ on 9th day post-inoculation. Doubling time was 24.25 h. Tumor growth induced cachexia, but no hematological or biochemical alterations. This model behaved as an undifferentiated tumor and can be promising for studying tumor cell migration in the central nervous system. Dexamethasone 3.0 mg/kg/day diminished significantly survival in this model. Cyclosporine 10 mg/kg/day administration was safely tolerated.

  4. A simplified procedure of linear regression in a preliminary analysis

    Directory of Open Access Journals (Sweden)

    Silvia Facchinetti

    2013-05-01

    Full Text Available The analysis of a statistical large data-set can be led by the study of a particularly interesting variable Y – regressed – and an explicative variable X, chosen among the remained variables, conjointly observed. The study gives a simplified procedure to obtain the functional link of the variables y=y(x by a partition of the data-set into m subsets, in which the observations are synthesized by location indices (mean or median of X and Y. Polynomial models for y(x of order r are considered to verify the characteristics of the given procedure, in particular we assume r= 1 and 2. The distributions of the parameter estimators are obtained by simulation, when the fitting is done for m= r + 1. Comparisons of the results, in terms of distribution and efficiency, are made with the results obtained by the ordinary least square methods. The study also gives some considerations on the consistency of the estimated parameters obtained by the given procedure.

  5. Simplified risk model support for environmental management integration

    International Nuclear Information System (INIS)

    Eide, S.A.; Jones, J.L.; Wierman, T.E.

    1998-01-01

    This paper summarizes the process and results of human health risk assessments of the US Department of Energy (DOE) complex-wide programs for high-level waste, transuranic waste, low-level, mixed low-level waste, and spent nuclear fuel. The DOE baseline programs and alternatives for these five material types were characterized by disposition maps (material flow diagrams) and supporting information in the May 1997 report 'A Contractor Report to the Department of Energy on Environmental Baseline Programs and Integration Opportunities' (Discussion Draft). Risk analyses were performed using the Simplified Risk Model (SRM), developed to support DOE Environmental Management Integration studies. The SRM risk analyses consistently and comprehensively cover the life cycle programs for the five material types, from initial storage through final disposition. Risk results are presented at several levels: DOE complex-wide, material type program, individual DOE sites, and DOE site activities. The detailed risk results are documented in the February 1998 report 'Human Health Risk Comparisons for Environmental Management Baseline Programs and Integration Opportunities' (Discussion Draft)

  6. Adolescent cocaine exposure simplifies orbitofrontal cortical dendritic arbors

    Directory of Open Access Journals (Sweden)

    Lauren M DePoy

    2014-10-01

    Full Text Available Cocaine and amphetamine remodel dendritic spines within discrete cortico-limbic brain structures including the orbitofrontal cortex (oPFC. Whether dendrite structure is similarly affected, and whether pre-existing cellular characteristics influence behavioral vulnerabilities to drugs of abuse, remain unclear. Animal models provide an ideal venue to address these issues because neurobehavioral phenotypes can be defined both before, and following, drug exposure. We exposed mice to cocaine from postnatal days 31-35, corresponding to early adolescence, using a dosing protocol that causes impairments in an instrumental reversal task in adulthood. We then imaged and reconstructed excitatory neurons in deep-layer oPFC. Prior cocaine exposure shortened and simplified arbors, particularly in the basal region. Next, we imaged and reconstructed orbital neurons in a developmental-genetic model of cocaine vulnerability – the p190rhogap+/- mouse. p190RhoGAP is an actin cytoskeleton regulatory protein that stabilizes dendrites and dendritic spines, and p190rhogap+/- mice develop rapid and robust locomotor activation in response to cocaine. Despite this, oPFC dendritic arbors were intact in drug-naïve p190rhogap+/- mice. Together, these findings provide evidence that adolescent cocaine exposure has long-term effects on dendrite structure in the oPFC, and they suggest that cocaine-induced modifications in dendrite structure may contribute to the behavioral effects of cocaine more so than pre-existing structural abnormalities in this cell population.

  7. Simplified human thermoregulatory model for designing wearable thermoelectric devices

    Science.gov (United States)

    Wijethunge, Dimuthu; Kim, Donggyu; Kim, Woochul

    2018-02-01

    Research on wearable and implantable devices have become popular with the strong need in market. A precise understanding of the thermal properties of human skin, which are not constant values but vary depending on ambient condition, is required for the development of such devices. In this paper, we present simplified human thermoregulatory model for accurately estimating the thermal properties of the skin without applying rigorous calculations. The proposed model considers a variable blood flow rate through the skin, evaporation functions, and a variable convection heat transfer from the skin surface. In addition, wearable thermoelectric generation (TEG) and refrigeration devices were simulated. We found that deviations of 10-60% can be resulted in estimating TEG performance without considering human thermoregulatory model owing to the fact that thermal resistance of human skin is adapted to ambient condition. Simplicity of the modeling procedure presented in this work could be beneficial for optimizing and predicting the performance of any applications that are directly coupled with skin thermal properties.

  8. A simplified model of saltcake moisture distribution. Letter report

    International Nuclear Information System (INIS)

    Simmons, C.S.

    1995-09-01

    This letter report describes the formulation of a simplified model for finding the moisture distribution in a saltcake waste profile that has been stabilized by pumping out the drainable interstitial liquid. The model is based on assuming that capillarity mainly governs the distribution of moisture in the porous saltcake waste. A stead upward flow of moisture driven by evaporation from the waste surface is conceptualized to occur for isothermal conditions. To obtain hydraulic parameters for unsaturated conditions, the model is calibrated or matched to the relative saturation distribution as measured by neutron probe scans. The model is demonstrated on Tanks 104-BY and 105-TX as examples. A value of the model is that it identifies the key physical parameters that control the surface moisture content in a waste profile. Moreover, the model can be used to estimate the brine application rate at the waste surface that would raise the moisture content there to a safe level. Thus, the model can be applied to help design a strategy for correcting the moisture conditions in a saltcake waste tank

  9. Simplified TiO2 force fields for studies of its interaction with biomolecules

    Science.gov (United States)

    Luan, Binquan; Huynh, Tien; Zhou, Ruhong

    2015-06-01

    Engineered TiO2 nanoparticles have been routinely applied in nanotechnology, as well as in cosmetics and food industries. Despite active experimental studies intended to clarify TiO2's biological effects, including potential toxicity, the relation between experimentally inferred nanotoxicity and industry standards for safely applying nanoparticles remains somewhat ambiguous with justified concerns. Supplemental to experiments, molecular dynamics simulations have proven to be efficacious in investigating the molecular mechanism of a biological process occurring at nanoscale. In this article, to facilitate the nanotoxicity and nanomedicine research related to this important metal oxide, we provide a simplified force field, based on the original Matsui-Akaogi force field but compatible to the Lennard-Jones potentials normally used in modeling biomolecules, for simulating TiO2 nanoparticles interacting with biomolecules. The force field parameters were tested in simulating the bulk structure of TiO2, TiO2 nanoparticle-water interaction, as well as the adsorption of proteins on the TiO2 nanoparticle. We demonstrate that these simulation results are consistent with experimental data/observations. We expect that simulations will help to better understand the interaction between TiO2 and molecules.

  10. Simplified analysis of frame structures with viscoelastic dampers considering the effect of soil-structure interaction

    Science.gov (United States)

    Zhao, Xuefei; Wang, Shuguang; Du, Dongsheng; Liu, Weiqing

    2017-01-01

    In this study, simplified numerical models are developed to analyze the soil-structure interaction (SSI) effect on frame structures equipped with viscoelastic dampers (VEDs) based on pile group foundation. First, a single degree-of-freedom (SDOF) oscillator is successfully utilized to replace the SDOF energy dissipated structure considering the SSI effect. The equivalent period and damping ratio of the system are obtained through analogical analysis using the frequency transfer function with adoption of the modal strain energy (MSE) technique. A parametric analysis is carried out to study the SSI effect on the performance of VEDs. Then the equilibrium equations of the multi degree-of-freedom (MDOF) structure with VEDs considering SSI effect are established in the frequency domain. Based on the assumption that the superstructure of the coupled system possesses the classical normal mode, the MDOF superstructure is decoupled to a set of individual SDOF systems resting on a rigid foundation with adoption of the MSE technique through formula derivation. Numerical results demonstrate that the proposed methods have the advantage of reducing computational cost, however, retaining the satisfactory accuracy. The numerical method proposed herein can provide a fast evaluation of the efficiency of VEDs considering the SSI effect.

  11. A teaching resource using the GUIDE environment: simplified model of the eye for secondary school students

    Science.gov (United States)

    Gómez-Varela, A. I.; Salvado-Vara, F.; Bao-Varela, C.

    2014-07-01

    Nowadays, new technologies have great influence on our lives and how we access to the information. The new generations have never known a world without them and make use of these new technologies in practically all facets of their day-to-day. Education systems have also evolved rapidly and frequently make use of learning strategies based on interactive tools. In this work we have created a graphical user interface with GUIDE, a development environment of MATLAB, to show, in a simple way, how the eye works. This interactive program is addressed to the first courses of secondary education and designed to introduce them to the basic concepts of the normal refractive condition of the eye and the most common refractive errors, as myopia and hyperopia. The graphic interface makes use of the simplified model of the eye, where the optic system of the visual organ is represented by a converging lens (cornea and crystalline) and a screen (retina). Emmetropic, myopic and hyperopic eye operation is shown graphically to the students, as well as how these focusing errors can be solved with a diverging and converging lens, respectively. This teaching tool was used this academic course in the Colegio Hogar de Santa Margarita (A Coruña) for a better understanding of the students in this matter and to catch their attention to the world of Optics and its importance.

  12. Simplifying numerical ray tracing for two-dimensional non circularly symmetric models of the human eye.

    Science.gov (United States)

    Jesus, Danilo A; Iskander, D Robert

    2015-12-01

    Ray tracing is a powerful technique to understand the light behavior through an intricate optical system such as that of a human eye. The prediction of visual acuity can be achieved through characteristics of an optical system such as the geometrical point spread function. In general, its precision depends on the number of discrete rays and the accurate surface representation of each eye's components. Recently, a method that simplifies calculation of the geometrical point spread function has been proposed for circularly symmetric systems [Appl. Opt.53, 4784 (2014)]. An extension of this method to 2D noncircularly symmetric systems is proposed. In this method, a two-dimensional ray tracing procedure for an arbitrary number of surfaces and arbitrary surface shapes has been developed where surfaces, rays, and refractive indices are all represented in functional forms being approximated by Chebyshev polynomials. The Liou and Brennan anatomically accurate eye model has been adapted and used for evaluating the method. Further, real measurements of the anterior corneal surface of normal, astigmatic, and keratoconic eyes were substituted for the first surface in the model. The results have shown that performing ray tracing, utilizing the two-dimensional Chebyshev function approximation, is possible for noncircularly symmetric models, and that such calculation can be performed with a newly created Chebfun toolbox.

  13. Simulator Evaluation of Simplified Propulsion-Only Emergency Flight Control Systems on Transport Aircraft

    Science.gov (United States)

    Burcham, Frank W., Jr.; Kaneshige, John; Bull, John; Maine, Trindel A.

    1999-01-01

    With the advent of digital engine control systems, considering the use of engine thrust for emergency flight control has become feasible. Many incidents have occurred in which engine thrust supplemented or replaced normal aircraft flight controls. In most of these cases, a crash has resulted, and more than 1100 lives have been lost. The NASA Dryden Flight Research Center has developed a propulsion-controlled aircraft (PCA) system in which computer-controlled engine thrust provides emergency flight control capability. Using this PCA system, an F-15 and an MD-11 airplane have been landed without using any flight controls. In simulations, C-17, B-757, and B-747 PCA systems have also been evaluated successfully. These tests used full-authority digital electronic control systems on the engines. Developing simpler PCA systems that can operate without full-authority engine control, thus allowing PCA technology to be installed on less capable airplanes or at lower cost, is also a desire. Studies have examined simplified ?PCA Ultralite? concepts in which thrust control is provided using an autothrottle system supplemented by manual differential throttle control. Some of these concepts have worked well. The PCA Ultralite study results are presented for simulation tests of MD-11, B-757, C-17, and B-747 aircraft.

  14. Theory of normal metals

    International Nuclear Information System (INIS)

    Mahan, G.D.

    1992-01-01

    The organizers requested that I give eight lectures on the theory of normal metals, ''with an eye on superconductivity.'' My job was to cover the general properties of metals. The topics were selected according to what the students would need to known for the following lectures on superconductivity. My role was to prepare the ground work for the later lectures. The problem is that there is not yet a widely accepted theory for the mechanism which pairs the electrons. Many mechanisms have been proposed, with those of phonons and spin fluctuations having the most followers. So I tried to discuss both topics. I also introduced the tight-binding model for metals, which forms the basis for most of the work on the cuprate superconductors

  15. Bifurcation analysis of the simplified models of boiling water reactor and identification of global stability boundary

    Energy Technology Data Exchange (ETDEWEB)

    Pandey, Vikas; Singh, Suneet, E-mail: suneet.singh@iitb.ac.in

    2017-04-15

    Highlights: • Non-linear stability analysis of nuclear reactor is carried out. • Global and local stability boundaries are drawn in the parameter space. • Globally stable, bi-stable, and unstable regions have been demarcated. • The identification of the regions is verified by numerical simulations. - Abstract: Nonlinear stability study of the neutron coupled thermal hydraulics instability has been carried out by several researchers for boiling water reactors (BWRs). The focus of these studies has been to identify subcritical and supercritical Hopf bifurcations. Supercritical Hopf bifurcation are soft or safe due to the fact that stable limit cycles arise in linearly unstable region; linear and global stability boundaries are same for this bifurcation. It is well known that the subcritical bifurcations can be considered as hard or dangerous due to the fact that unstable limit cycles (nonlinear phenomena) exist in the (linearly) stable region. The linear stability leads to a stable equilibrium in such regions, only for infinitesimally small perturbations. However, finite perturbations lead to instability due to the presence of unstable limit cycles. Therefore, it is evident that the linear stability analysis is not sufficient to understand the exact stability characteristics of BWRs. However, the effect of these bifurcations on the stability boundaries has been rarely discussed. In the present work, the identification of global stability boundary is demonstrated using simplified models. Here, five different models with different thermal hydraulics feedback have been investigated. In comparison to the earlier works, current models also include the impact of adding the rate of change in temperature on void reactivity as well as effect of void reactivity on rate of change of temperature. Using the bifurcation analysis of these models the globally stable region in the parameter space has been identified. The globally stable region has only stable solutions and

  16. Bifurcation analysis of the simplified models of boiling water reactor and identification of global stability boundary

    International Nuclear Information System (INIS)

    Pandey, Vikas; Singh, Suneet

    2017-01-01

    Highlights: • Non-linear stability analysis of nuclear reactor is carried out. • Global and local stability boundaries are drawn in the parameter space. • Globally stable, bi-stable, and unstable regions have been demarcated. • The identification of the regions is verified by numerical simulations. - Abstract: Nonlinear stability study of the neutron coupled thermal hydraulics instability has been carried out by several researchers for boiling water reactors (BWRs). The focus of these studies has been to identify subcritical and supercritical Hopf bifurcations. Supercritical Hopf bifurcation are soft or safe due to the fact that stable limit cycles arise in linearly unstable region; linear and global stability boundaries are same for this bifurcation. It is well known that the subcritical bifurcations can be considered as hard or dangerous due to the fact that unstable limit cycles (nonlinear phenomena) exist in the (linearly) stable region. The linear stability leads to a stable equilibrium in such regions, only for infinitesimally small perturbations. However, finite perturbations lead to instability due to the presence of unstable limit cycles. Therefore, it is evident that the linear stability analysis is not sufficient to understand the exact stability characteristics of BWRs. However, the effect of these bifurcations on the stability boundaries has been rarely discussed. In the present work, the identification of global stability boundary is demonstrated using simplified models. Here, five different models with different thermal hydraulics feedback have been investigated. In comparison to the earlier works, current models also include the impact of adding the rate of change in temperature on void reactivity as well as effect of void reactivity on rate of change of temperature. Using the bifurcation analysis of these models the globally stable region in the parameter space has been identified. The globally stable region has only stable solutions and

  17. Limitations, insights and improvements to gyrokinetics

    International Nuclear Information System (INIS)

    Catto, Peter J.; Parra, Felix I.; Kagan, Grigory; Simakov, Andrei N.

    2009-01-01

    We first consider gyrokinetic quasineutrality limitations when evaluating the axisymmetric radial electric field in a non-turbulent tokamak by an improved examination of intrinsic ambipolarity. We next prove that the background ions in a pedestal of poloidal ion gyroradius scale must be Maxwellian and nearly isothermal in Pfirsch-Schlueter and banana regime tokamak plasmas, and then consider zonal flow behaviour in a pedestal. Finally, we focus on a simplifying procedure for our transport time scale hybrid gyrokinetic-fluid treatment that removes the limitations of gyrokinetic quasineutrality and remains valid in the pedestal.

  18. Improved Simplified Methods for Effective Seismic Analysis and Design of Isolated and Damped Bridges in Western and Eastern North America

    Science.gov (United States)

    Koval, Viacheslav

    The seismic design provisions of the CSA-S6 Canadian Highway Bridge Design Code and the AASHTO LRFD Seismic Bridge Design Specifications have been developed primarily based on historical earthquake events that have occurred along the west coast of North America. For the design of seismic isolation systems, these codes include simplified analysis and design methods. The appropriateness and range of application of these methods are investigated through extensive parametric nonlinear time history analyses in this thesis. It was found that there is a need to adjust existing design guidelines to better capture the expected nonlinear response of isolated bridges. For isolated bridges located in eastern North America, new damping coefficients are proposed. The applicability limits of the code-based simplified methods have been redefined to ensure that the modified method will lead to conservative results and that a wider range of seismically isolated bridges can be covered by this method. The possibility of further improving current simplified code methods was also examined. By transforming the quantity of allocated energy into a displacement contribution, an idealized analytical solution is proposed as a new simplified design method. This method realistically reflects the effects of ground-motion and system design parameters, including the effects of a drifted oscillation center. The proposed method is therefore more appropriate than current existing simplified methods and can be applicable to isolation systems exhibiting a wider range of properties. A multi-level-hazard performance matrix has been adopted by different seismic provisions worldwide and will be incorporated into the new edition of the Canadian CSA-S6-14 Bridge Design code. However, the combined effect and optimal use of isolation and supplemental damping devices in bridges have not been fully exploited yet to achieve enhanced performance under different levels of seismic hazard. A novel Dual-Level Seismic

  19. 20 CFR 404.241 - 1977 simplified old-start method.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false 1977 simplified old-start method. 404.241... DISABILITY INSURANCE (1950- ) Computing Primary Insurance Amounts Old-Start Method of Computing Primary Insurance Amounts § 404.241 1977 simplified old-start method. (a) Who is qualified. To qualify for the old...

  20. Transfer of Perceptual Expertise: The Case of Simplified and Traditional Chinese Character Recognition

    Science.gov (United States)

    Liu, Tianyin; Chuk, Tin Yim; Yeh, Su-Ling; Hsiao, Janet H.

    2016-01-01

    Expertise in Chinese character recognition is marked by reduced holistic processing (HP), which depends mainly on writing rather than reading experience. Here we show that, while simplified and traditional Chinese readers demonstrated a similar level of HP when processing characters shared between the simplified and traditional scripts, simplified…

  1. Significance, progress and prospects for research in simplified cultivation technologies for rice in China.

    Science.gov (United States)

    Huang, M; Ibrahim, Md; Xia, B; Zou, Y

    2011-08-01

    Simplified cultivation technologies for rice have become increasingly attractive in recent years in China because of their social, economical and environmental benefits. To date, several simplified cultivation technologies, such as conventional tillage and seedling throwing (CTST), conventional tillage and direct seeding (CTDS), no-tillage and seedling throwing (NTST), no-tillage and direct seeding (NTDS) and no-tillage and transplanting (NTTP), have been developed in China. Most studies have shown that rice grown under each of these simplified cultivation technologies can produce a grain yield equal to or higher than traditional cultivation (conventional tillage and transplanting). Studies that have described the influences of agronomic practices on yield formation of rice under simplified cultivation have demonstrated that optimizing agronomy practices would increase the efficiencies of simplified cultivation systems. Further research is needed to optimize the management strategies for CTST, CTDS and NTST rice which have developed quickly in recent years, to strengthen basic research for those simplified cultivation technologies that are rarely used at present (such as NTTP and NTDS), to select and breed cultivars suitable for simplified cultivation and to compare the practicability and effectiveness of different simplified cultivation technologies in different rice production regions.

  2. 48 CFR 2953.102 - Quotation for Simplified Acquisitions DL 1-2078.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Quotation for Simplified Acquisitions DL 1-2078. 2953.102 Section 2953.102 Federal Acquisition Regulations System DEPARTMENT OF LABOR CLAUSE AND FORMS FORMS General 2953.102 Quotation for Simplified Acquisitions DL 1-2078. The following...

  3. Sine sweep and steady-state response of simplified solar array models with nonlinear elements

    NARCIS (Netherlands)

    Fey, R.H.B.; van Liempt, F.P.H.

    2002-01-01

    In this paper the nonlinear dynamic behaviour of two simplified solar array systems is investigated experimentally and numerically. A simplified beam model supported by one snubber (a bilinear spring which can only take compressive forces) is used to investigate the dynamics of the extension arm on

  4. Simplified and representative bacterial community of maize roots.

    Science.gov (United States)

    Niu, Ben; Paulson, Joseph Nathaniel; Zheng, Xiaoqi; Kolter, Roberto

    2017-03-21

    Plant-associated microbes are important for the growth and health of their hosts. As a result of numerous prior studies, we know that host genotypes and abiotic factors influence the composition of plant microbiomes. However, the high complexity of these communities challenges detailed studies to define experimentally the mechanisms underlying the dynamics of community assembly and the beneficial effects of such microbiomes on plant hosts. In this work, from the distinctive microbiota assembled by maize roots, through host-mediated selection, we obtained a greatly simplified synthetic bacterial community consisting of seven strains ( Enterobacter cloacae , Stenotrophomonas maltophilia, Ochrobactrum pituitosum, Herbaspirillum frisingense, Pseudomonas putida, Curtobacterium pusillum , and Chryseobacterium indologenes ) representing three of the four most dominant phyla found in maize roots. By using a selective culture-dependent method to track the abundance of each strain, we investigated the role that each plays in community assembly on roots of axenic maize seedlings. Only the removal of E. cloacae led to the complete loss of the community, and C. pusillum took over. This result suggests that E. cloacae plays the role of keystone species in this model ecosystem. In planta and in vitro, this model community inhibited the phytopathogenic fungus Fusarium verticillioides , indicating a clear benefit to the host. Thus, combined with the selective culture-dependent quantification method, our synthetic seven-species community representing the root microbiome has the potential to serve as a useful system to explore how bacterial interspecies interactions affect root microbiome assembly and to dissect the beneficial effects of the root microbiota on hosts under laboratory conditions in the future.

  5. Office of River Protection: Simplifying Project management tools

    International Nuclear Information System (INIS)

    TAYLOR, D.G.

    2000-01-01

    The primary approach to the effort was to form a multi-organizational team comprised of federal and contractor staff to develop and implement the necessary tools and systems to manage the project. In late 1999 the DOE Manager of the Office of River Protection formed the Project Integration Office to achieve the objective of managing the efforts as a single project. The first major task, and the foundation upon which to base the development of all other tools, was the establishment of a single baseline of activities. However, defining a single scope schedule and cost was a difficult matter indeed. Work scopes were available throughout the project, but the level of detail and the integration of the activities existed primarily between working groups and individuals and not on a project-wide basis. This creates a situation where technical needs, logic flaws, resource balancing, and other similar integration needs are not elevated for management attention and resolution. It should be noted that probably 90% of the interface issues were known and being addressed. The key is simplifying the process and providing tangible assurance that the other 10% does not contain issues that can delay the project. Fortunately all of the contractors employed a common scheduling tool, which served as the basis for first communicating and then integrating baseline activities. Utilizing a powerful computer-based scheduling tool, it was soon possible to integrate the various schedules after the following was accomplished: Establishment of a scheduling specification (standardized input, coding, and approach to logic); and Clearly defined project assumptions

  6. Evaluating performances of simplified physically based landslide susceptibility models.

    Science.gov (United States)

    Capparelli, Giovanna; Formetta, Giuseppe; Versace, Pasquale

    2015-04-01

    Rainfall induced shallow landslides cause significant damages involving loss of life and properties. Prediction of shallow landslides susceptible locations is a complex task that involves many disciplines: hydrology, geotechnical science, geomorphology, and statistics. Usually to accomplish this task two main approaches are used: statistical or physically based model. This paper presents a package of GIS based models for landslide susceptibility analysis. It was integrated in the NewAge-JGrass hydrological model using the Object Modeling System (OMS) modeling framework. The package includes three simplified physically based models for landslides susceptibility analysis (M1, M2, and M3) and a component for models verifications. It computes eight goodness of fit indices (GOF) by comparing pixel-by-pixel model results and measurements data. Moreover, the package integration in NewAge-JGrass allows the use of other components such as geographic information system tools to manage inputs-output processes, and automatic calibration algorithms to estimate model parameters. The system offers the possibility to investigate and fairly compare the quality and the robustness of models and models parameters, according a procedure that includes: i) model parameters estimation by optimizing each of the GOF index separately, ii) models evaluation in the ROC plane by using each of the optimal parameter set, and iii) GOF robustness evaluation by assessing their sensitivity to the input parameter variation. This procedure was repeated for all three models. The system was applied for a case study in Calabria (Italy) along the Salerno-Reggio Calabria highway, between Cosenza and Altilia municipality. The analysis provided that among all the optimized indices and all the three models, Average Index (AI) optimization coupled with model M3 is the best modeling solution for our test case. This research was funded by PON Project No. 01_01503 "Integrated Systems for Hydrogeological Risk

  7. Data analytics for simplifying thermal efficiency planning in cities.

    Science.gov (United States)

    Abdolhosseini Qomi, Mohammad Javad; Noshadravan, Arash; Sobstyl, Jake M; Toole, Jameson; Ferreira, Joseph; Pellenq, Roland J-M; Ulm, Franz-Josef; Gonzalez, Marta C

    2016-04-01

    More than 44% of building energy consumption in the USA is used for space heating and cooling, and this accounts for 20% of national CO2emissions. This prompts the need to identify among the 130 million households in the USA those with the greatest energy-saving potential and the associated costs of the path to reach that goal. Whereas current solutions address this problem by analysing each building in detail, we herein reduce the dimensionality of the problem by simplifying the calculations of energy losses in buildings. We present a novel inference method that can be used via a ranking algorithm that allows us to estimate the potential energy saving for heating purposes. To that end, we only need consumption from records of gas bills integrated with a building's footprint. The method entails a statistical screening of the intricate interplay between weather, infrastructural and residents' choice variables to determine building gas consumption and potential savings at a city scale. We derive a general statistical pattern of consumption in an urban settlement, reducing it to a set of the most influential buildings' parameters that operate locally. By way of example, the implications are explored using records of a set of (N= 6200) buildings in Cambridge, MA, USA, which indicate that retrofitting only 16% of buildings entails a 40% reduction in gas consumption of the whole building stock. We find that the inferred heat loss rate of buildings exhibits a power-law data distribution akin to Zipf's law, which provides a means to map an optimum path for gas savings per retrofit at a city scale. These findings have implications for improving the thermal efficiency of cities' building stock, as outlined by current policy efforts seeking to reduce home heating and cooling energy consumption and lower associated greenhouse gas emissions. © 2016 The Author(s).

  8. Simplified modeling photo-ionisation of uranium in Silva project

    International Nuclear Information System (INIS)

    Bodin, B.; Pourre-Brichot, P.; Valadier, L.

    2000-01-01

    SILVA is a process which targets 235 U by photo-ionization. It is therefore important to compute the proportion of ionized atoms depending on the properties of the lasers. The interaction between atoms and lasers occurs via the link between the Maxwell and Schroedinger equations. This kind of approach is only feasible for a few simple cases: e.g. wave plane or simple laser profiling. Introducing the characteristics of SILVA, computation time increases substantially (several hundred days per kilogram of vapor). To circumvent this problem, we wrote a program (Jackpot) that treats photo-ionization by a simplified model: kinetics equations. However, various optical components were introduced with absorption factor by wavelength, to account for the effects of optics systems on the trajectory. Instead of seeking the complex wavefunction solutions of the Maxwell-Schroedinger equations, we solve a system where the unknown values are a set of populations. The size of the set depends only on the number of hold points in the process. Recent work shows that we can converge towards the same results as the Maxwell-Schroedinger system if we can fit the cross-sections of the kinetic system correctly. As to the optical aspect, Jackpot can handle diffraction. In this case, it solves the propagation equation of an electric field by a double Fourier transform method. For interactions with mirrors, the new direction of a ray is calculated with Descartes law, applying a numerical phase mask to the electric field. We account for diaphragmation mechanisms as well as the absorption law for each mirror, by a real factor by wavelength. Jackpot is simple to use and can be used to predict experimental results. Jackpot is now a library calling by a script written in Python. Changes are being made for a closer approach to reality (real laser, new photo-ionization model)

  9. GeoDataspaces: Simplifying Data Management Tasks with Globus

    Science.gov (United States)

    Malik, T.; Chard, K.; Tchoua, R. B.; Foster, I.

    2014-12-01

    Data and its management are central to modern scientific enterprise. Typically, geoscientists rely on observations and model output data from several disparate sources (file systems, RDBMS, spreadsheets, remote data sources). Integrated data management solutions that provide intuitive semantics and uniform interfaces, irrespective of the kind of data source are, however, lacking. Consequently, geoscientists are left to conduct low-level and time-consuming data management tasks, individually, and repeatedly for discovering each data source, often resulting in errors in handling. In this talk we will describe how the EarthCube GeoDataspace project is improving this situation for seismologists, hydrologists, and space scientists by simplifying some of the existing data management tasks that arise when developing computational models. We will demonstrate a GeoDataspace, bootstrapped with "geounits", which are self-contained metadata packages that provide complete description of all data elements associated with a model run, including input/output and parameter files, model executable and any associated libraries. Geounits link raw and derived data as well as associating provenance information describing how data was derived. We will discuss challenges in establishing geounits and describe machine learning and human annotation approaches that can be used for extracting and associating ad hoc and unstructured scientific metadata hidden in binary formats with data resources and models. We will show how geounits can improve search and discoverability of data associated with model runs. To support this model, we will describe efforts related towards creating a scalable metadata catalog that helps to maintain, search and discover geounits within the Globus network of accessible endpoints. This talk will focus on the issue of creating comprehensive personal inventories of data assets for computational geoscientists, and describe a publishing mechanism, which can be used to

  10. Simplified model for radioactive contaminant transport: the TRANSS code

    International Nuclear Information System (INIS)

    Simmons, C.S.; Kincaid, C.T.; Reisenauer, A.E.

    1986-09-01

    A simplified ground-water transport model called TRANSS was devised to estimate the rate of migration of a decaying radionuclide that is subject to sorption governed by a linear isotherm. Transport is modeled as a contaminant mass transmitted along a collection of streamlines constituting a streamtube, which connects a source release zone with an environmental arrival zone. The probability-weighted contaminant arrival distribution along each streamline is represented by an analytical solution of the one-dimensional advection-dispersion equation with constant velocity and dispersion coefficient. The appropriate effective constant velocity for each streamline is based on the exact travel time required to traverse a streamline with a known length. An assumption used in the model to facilitate the mathematical simplification is that transverse dispersion within a streamtube is negligible. Release of contaminant from a source is described in terms of a fraction-remaining curve provided as input information. However, an option included in the code is the calculation of a fraction-remaining curve based on four specialized release models: (1) constant release rate, (2) solubility-controlled release, (3) adsorption-controlled release, and (4) diffusion-controlled release from beneath an infiltration barrier. To apply the code, a user supplies only a certain minimal number of parameters: a probability-weighted list of travel times for streamlines, a local-scale dispersion coefficient, a sorption distribution coefficient, total initial radionuclide inventory, radioactive half-life, a release model choice, and size dimensions of the source. The code is intended to provide scoping estimates of contaminant transport and does not predict the evolution of a concentration distribution in a ground-water flow field. Moreover, the required travel times along streamlines must be obtained from a prior ground-water flow simulation

  11. Knowledge Management Portal: A Simplified Model to Help Decision Makers

    International Nuclear Information System (INIS)

    Ogawa, I.; Hernandes Tabares, R.

    2015-01-01

    The aim of this work is to present a simplified model that could help the nuclear industry to keep the expertise of safeguards professionals in touch with the state of the art, and also to have available information in the Portal of Knowledge Management. It can also provide indicators and general data for decision makers. Authors have developed the concept based on their own experience through systems running in hydroelectric and gas fired plants, and one exclusive system that manage all courses in one University. It is under development a Portal of Knowledge Management for NPP dealing with information obtained of Strategic Plans, Budgets and Economics, Operation Performance, Maintenance and Surveillance Plans, Training and Education Programs, QA Programs, Operational Experience, Safety Culture, and Engineering of Human Factors. This model will provide indicators for decision makers. Training and education module is prepared according to profile of each individual and his attributes, tasks and capabilities, and training and education programmes. The system could apply self-assessment questionnaires; immersive learning using media (video) classes, and test applications using questions randomly selected from data bank, as well as could make applications to certificate people. All these data are analyzed and generate indicators about strongest and weakness points. Managers could have indication of individual's deficiency even though in training programmes on a real time basis. Another tool that could be applied to the model is the remote operation of supervision equipment. The model is developed using web-based tools, like ASP.NET encrypted by 128 bits, and web site https. Finally, it is important to stress that the model can be customized according to industry preference. (author)

  12. Uncertainty analysis of the Operational Simplified Surface Energy Balance (SSEBop) model at multiple flux tower sites

    Science.gov (United States)

    Chen, Mingshi; Senay, Gabriel B.; Singh, Ramesh K.; Verdin, James P.

    2016-01-01

    the normal range. This finding implies that the simplified parameterization of the SSEBop model did not significantly affect the accuracy of the ET estimate while increasing the ease of model setup for operational applications. The sensitivity analysis indicated that the SSEBop model is most sensitive to input variables, land surface temperature (LST) and reference ET (ETo); and parameters, differential temperature (dT), and maximum ET scalar (Kmax), particularly during the non-growing season and in dry areas. In summary, the uncertainty assessment verifies that the SSEBop model is a reliable and robust method for large-area ET estimation. The SSEBop model estimates can be further improved by reducing errors in two input variables (ETo and LST) and two key parameters (Kmax and dT).

  13. Radiodine treatment of hyperthyroidism with a simplified dosimetric approach. Clinical results

    International Nuclear Information System (INIS)

    Giovanella, L.; De Palma, D.; Ceriani, L.; Garancini, S.; Vanoli, P.; Tordiglione, M.; Tarolo, G. L.

    2000-01-01

    12 of 146% (8%) patients hyperthyroid. Two patients were immediately submitted to a new radioiodine administration. One year posttreatment 142 of 146 (97%) patients were euthyroid while only 4 of 146 (3%) patients showed TSH levels above the normal range. Only 2 of them required thyroxine treatment. The simplified dosimetric method illustrated in this paper is very effective in clinical practice because it permits to avoid resorting to sophisticated but also imprecise quantitative methods. Hypothyroidism should not be considered as a major collateral effect of radioiodine treatment, particularly in Graves' disease. In fact, the pathogenesis of the disease requires an ablative treatment with both surgery and radioiodine treatment and the control of hyperthyroidism and the prevention of relapse are the major clinical targets. Vice versa, hypothyroidism was very uncommon in uni- and multinodular toxic goiter when the dosimetric approach was applied [it

  14. A simplified computational scheme for thermal analysis of LWR spent fuel dry storage and transportation casks

    International Nuclear Information System (INIS)

    Kim, Chang Hyun

    1997-02-01

    A simplified computational scheme for thermal analysis of the LWR spent fuel dry storage and transportation casks has been developed using two-step thermal analysis method incorporating effective thermal conductivity model for the homogenized spent fuel assembly. Although a lot of computer codes and analytical models have been developed for application to the fields of thermal analysis of dry storage and/or transportation casks, some difficulties in its analysis arise from the complexity of the geometry including the rod bundles of spent fuel and the heat transfer phenomena in the cavity of cask. Particularly, if the disk-type structures such as fuel baskets and aluminium heat transfer fins are included, the thermal analysis problems in the cavity are very complex. To overcome these difficulties, cylindrical coordinate system is adopted to calculate the temperature profile of a cylindrical cask body using the multiple cylinder model as the step-1 analysis of the present study. In the step-2 analysis, Cartesian coordinate system is adopted to calculate the temperature distributions of the disk-type structures such as fuel basket and aluminium heat transfer fin using three- dimensional conduction analysis model. The effective thermal conductivity for homogenized spent fuel assembly based on Manteufel and Todreas model is incorporated in step-2 analysis to predict the maximum fuel temperature. The presented two-step computational scheme has been performed using an existing HEATING 7.2 code and the effective thermal conductivity for the homogenized spent fuel assembly has been calculated by additional numerical analyses. Sample analyses of five cases are performed for NAC-STC including normal transportation condition to examine the applicability of the presented simplified computational scheme for thermal analysis of the large LWR spent fuel dry storage and transportation casks and heat transfer characteristics in the cavity of the cask with the disk-type structures

  15. Analysis of limit cycling on a boiler feedwater control system

    International Nuclear Information System (INIS)

    Thomas, P.J.; Harrison, T.A.; Hollywell, P.D.

    1986-01-01

    During operation of the UKAEA Prototype Fast Reactor, it was found that oscillations sometimes occurred in the boiler feedwater systems. These were normally of relatively low amplitude, but led to the adoption of low controller gains so that control was rather slack. While control performance proved generally adequate for steady running, the lack of tight control of steam drum levels sometimes led to difficulties during periods when plant conditions were undergoing major change. The paper discusses the methods used to gain a full understanding of the phenomena occurring, and describes how that knowledge is being used to improve the control system so as to eliminate the limit cycling modes and ensure good control of steam drum levels. A noteworthy feature of the study was the use of two independent representations of plant behaviour: (i) a frequency response model, FWRFREQ, and (ii) a time-domain simulation model, PFRTDM. The simplified analysis of FWRFREQ proved to be of enormous value in identifying modes of system behaviour; PFRTDM was used as a detailed check on the accuracy and validity of the results obtained. (author)

  16. Simplified equations for the rotational speed response to inflow velocity variation in fixed-pitch small wind turbines

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H; Hasegawa, Y, E-mail: hsuzuki@nitech.ac.jp [Graduate School of Engineering, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555 (Japan)

    2015-02-01

    We propose simplified equations for the rotational speed response to inflow velocity variation in fixed-pitch small wind turbines. The present formulation is derived by introducing a series expansion for the torque coefficient at the constant tip-speed ratio. By focusing on the first- and second-order differential coefficients of the torque coefficient, we simplify the original differential equation. The governing equation based only on the first-order differential coefficient is found to be linear, whereas the second-order differential coefficient introduces nonlinearity. We compare the numerical solutions of the three governing equations for rotational speed in response to sinusoidal and normal-random variations of inflow velocity. The linear equation gives accurate solutions of amplitude and phase lag. Nonlinearity occurs in the mean value of rotational speed variation. We also simulate the rotational speed in response to a step input of inflow velocity using the conditions of two previous studies, and note that the form of this rotational speed response is a system of first-order time lag. We formulate the gain and time constant for this rotational speed response. The magnitude of the gain is approximately three when the wind turbine is operated at optimal tip-speed ratio. We discuss the physical meaning of the derived time constant. (paper)

  17. A simplified boron diffusion for preparing the silicon single crystal p-n junction as an educational device

    Energy Technology Data Exchange (ETDEWEB)

    Shiota, Koki, E-mail: a14510@sr.kagawa-nct.ac.jp; Kai, Kazuho; Nagaoka, Shiro, E-mail: nagaoka@es.kagawa-nct.ac.jp [National Institute of Technology, Kagawa College, Kagawa, Mitoyo, Takuma, Koda 551 (Japan); Tsuji, Takuto [National Institute of Technology, Suzuka College, Mie, Suzuka, Shiroko (Japan); Wakahara, Akihiro [Toyohashi University of Technology, Aichi, Toyohashi, Tenpaku, Hibarigaoka 1-1 (Japan); Rusop, Mohamad [University Technology Mara, Selangor, Shah Alam, 40450 (Malaysia)

    2016-07-06

    The educational method which is including designing, making, and evaluating actual semiconductor devices with learning the theory is one of the best way to obtain the fundamental understanding of the device physics and to cultivate the ability to make unique ideas using the knowledge in the semiconductor device. In this paper, the simplified Boron thermal diffusion process using Sol-Gel material under normal air environment was proposed based on simple hypothesis and the feasibility of the reproducibility and reliability were investigated to simplify the diffusion process for making the educational devices, such as p-n junction, bipolar and pMOS devices. As the result, this method was successfully achieved making p+ region on the surface of the n-type silicon substrates with good reproducibility. And good rectification property of the p-n junctions was obtained successfully. This result indicates that there is a possibility to apply on the process making pMOS or bipolar transistors. It suggests that there is a variety of the possibility of the applications in the educational field to foster an imagination of new devices.

  18. US ITER limiter module design

    International Nuclear Information System (INIS)

    Mattas, R.F.; Billone, M.; Hassanein, A.

    1996-08-01

    The recent U.S. effort on the ITER (International Thermonuclear Experimental Reactor) shield has been focused on the limiter module design. This is a multi-disciplinary effort that covers design layout, fabrication, thermal hydraulics, materials evaluation, thermo- mechanical response, and predicted response during off-normal events. The results of design analyses are presented. Conclusions and recommendations are also presented concerning, the capability of the limiter modules to meet performance goals and to be fabricated within design specifications using existing technology

  19. Simplifying BRDF input data for optical signature modeling

    Science.gov (United States)

    Hallberg, Tomas; Pohl, Anna; Fagerström, Jan

    2017-05-01

    Scene simulations of optical signature properties using signature codes normally requires input of various parameterized measurement data of surfaces and coatings in order to achieve realistic scene object features. Some of the most important parameters are used in the model of the Bidirectional Reflectance Distribution Function (BRDF) and are normally determined by surface reflectance and scattering measurements. Reflectance measurements of the spectral Directional Hemispherical Reflectance (DHR) at various incident angles can normally be performed in most spectroscopy labs, while measuring the BRDF is more complicated or may not be available at all in many optical labs. We will present a method in order to achieve the necessary BRDF data directly from DHR measurements for modeling software using the Sandford-Robertson BRDF model. The accuracy of the method is tested by modeling a test surface by comparing results from using estimated and measured BRDF data as input to the model. These results show that using this method gives no significant loss in modeling accuracy.

  20. Normal vibrations in gallium arsenide

    International Nuclear Information System (INIS)

    Dolling, G.; Waugh, J.L.T.

    1964-01-01

    The triple axis crystal spectrometer at Chalk River has been used to observe coherent slow neutron scattering from a single crystal of pure gallium arsenide at 296 o K. The frequencies of normal modes of vibration propagating in the [ζ00], (ζζζ], and (0ζζ] crystal directions have been determined with a precision of between 1 and 2·5 per cent. A limited number of normal modes have also been studied at 95 and 184 o K. Considerable difficulty was experienced in obtaining welt resolved neutron peaks corresponding to the two non-degenerate optic modes for very small wave-vector, particularly at 296 o K. However, from a comparison of results obtained under various experimental conditions at several different points in reciprocal space, frequencies (units 10 12 c/s) for these modes (at 296 o K) have been assigned: T 8·02±0·08 and L 8·55±02. Other specific normal modes, with their measured frequencies are (a) (1,0,0): TO 7·56 ± 008, TA 2·36 ± 0·015, LO 7·22 ± 0·15, LA 6·80 ± 0·06; (b) (0·5, 0·5, 0·5): TO 7·84 ± 0·12, TA 1·86 ± 0·02, LO 7·15 ± 0·07, LA 6·26 ± 0·10; (c) (0, 0·65, 0·65): optic 8·08 ±0·13, 7·54 ± 0·12 and 6·57 ± 0·11, acoustic 5·58 ± 0·08, 3·42 · 0·06 and 2·36 ± 004. These results are generally slightly lower than the corresponding frequencies for germanium. An analysis in terms of various modifications of the dipole approximation model has been carried out. A feature of this analysis is that the charge on the gallium atom appears to be very small, about +0·04 e. The frequency distribution function has been derived from one of the force models. (author)