WorldWideScience

Sample records for silicon grain boundary

  1. Interfacial state and potential barrier height associated with grain boundaries in polycrystalline silicon

    International Nuclear Information System (INIS)

    Tsurekawa, Sadahiro; Kido, Kota; Watanabe, Tadao

    2007-01-01

    Importance of polycrystalline silicon has been recognized in the electronic device technology. The interfacial states in the band-gap and potential barrier associated with grain boundaries in polycrystalline silicon can exert their detrimental influence on electrical conductivity and then on device performance. However, all grain boundaries are not similarly potential sites for electrical activity because individual grain boundaries have their own character depending on the orientation relation between two adjoining grains. We apply the electron-beam-induced current technique and the Kelvin probe force microscopy to observe the carrier recombination intensity and the potential barrier height, respectively, at well-characterized grain boundaries in semiconductor-grade polycrystalline silicon. The results are compared with the previously observed ones in solar-grade silicon to examine the factors affecting electrical activity of grain boundaries

  2. Grain boundary resistance to amorphization of nanocrystalline silicon carbide

    Science.gov (United States)

    Chen, Dong; Gao, Fei; Liu, Bo

    2015-01-01

    Under the C displacement condition, we have used molecular dynamics simulation to examine the effects of grain boundaries (GBs) on the amorphization of nanocrystalline silicon carbide (nc-SiC) by point defect accumulation. The results show that the interstitials are preferentially absorbed and accumulated at GBs that provide the sinks for defect annihilation at low doses, but also driving force to initiate amorphization in the nc-SiC at higher doses. The majority of surviving defects are C interstitials, as either C-Si or C-C dumbbells. The concentration of defect clusters increases with increasing dose, and their distributions are mainly observed along the GBs. Especially these small clusters can subsequently coalesce and form amorphous domains at the GBs during the accumulation of carbon defects. A comparison between displacement amorphized nc-SiC and melt-quenched single crystal SiC shows the similar topological features. At a dose of 0.55 displacements per atom (dpa), the pair correlation function lacks long range order, demonstrating that the nc-SiC is fully amorphilized. PMID:26558694

  3. Grain-boundary type and distribution in silicon carbide coatings and wafers

    Science.gov (United States)

    Cancino-Trejo, Felix; López-Honorato, Eddie; Walker, Ross C.; Ferrer, Romelia Salomon

    2018-03-01

    Silicon carbide is the main diffusion barrier against metallic fission products in TRISO (tristructural isotropic) coated fuel particles. The explanation of the accelerated diffusion of silver through SiC has remained a challenge for more than four decades. Although, it is now well accepted that silver diffuse through SiC by grain boundary diffusion, little is known about the characteristics of the grain boundaries in SiC and how these change depending on the type of sample. In this work five different types (coatings and wafers) of SiC produced by chemical vapor deposition were characterized by electron backscatter diffraction (EBSD). The SiC in TRISO particles had a higher concentration of high angle grain boundaries (aprox. 70%) compared to SiC wafers, which ranged between 30 and 60%. Similarly, SiC wafers had a higher concentration of low angle grain boundaries ranging between 15 and 30%, whereas TRISO particles only reached values of around 7%. The same trend remained when comparing the content of coincidence site lattice (CSL) boundaries, since SiC wafers showed a concentration of more than 30%, whilst TRISO particles had contents of around 20%. In all samples the largest fractions of CSL boundaries (3 ≤ Σ ≤ 17) were the Σ3 boundaries. We show that there are important differences between the SiC in TRISO particles and SiC wafers which could explain some of the differences observed in diffusion experiments in the literature.

  4. Diffusion of hydrogen from plasma source by grain boundaries in EFG silicon

    International Nuclear Information System (INIS)

    Fedotov, A.; Saad, Anis M.H.; Drozdov, N.; Mazanik, A.; Ulyashin, A.; Fahrner, W.R.; Stognii, A.

    2001-01-01

    Diffusion of atomized hydrogen along grain boundaries (GBs) studied by transformation of their electrical activity in p-type silicon bi crystalline samples cut from EFG silicon crystals was investigated. The changes in electrical activity of GBs was estimated relative to both minority (MiC) and majority (MaC) carriers and demonstrated the correlation between the type, structure and thermal pre-history of GBs. It was shown on the base of this study that diffusion along GBs depends essentially on three factors: type of GBs, state of ribbons (as-grown or annealed) and concurrence of grain boundary dangling bonds and boron passivation effects. The model of the longitudinal hydrogen diffusion that explains these results is proposed

  5. Correlating Atom Probe Tomography with Atomic-Resolved Scanning Transmission Electron Microscopy: Example of Segregation at Silicon Grain Boundaries.

    Science.gov (United States)

    Stoffers, Andreas; Barthel, Juri; Liebscher, Christian H; Gault, Baptiste; Cojocaru-Mirédin, Oana; Scheu, Christina; Raabe, Dierk

    2017-04-01

    In the course of a thorough investigation of the performance-structure-chemistry interdependency at silicon grain boundaries, we successfully developed a method to systematically correlate aberration-corrected scanning transmission electron microscopy and atom probe tomography. The correlative approach is conducted on individual APT and TEM specimens, with the option to perform both investigations on the same specimen in the future. In the present case of a Σ9 grain boundary, joint mapping of the atomistic details of the grain boundary topology, in conjunction with chemical decoration, enables a deeper understanding of the segregation of impurities observed at such grain boundaries.

  6. Silicon Σ13(5 0 1) grain boundary interface structure determined by bicrystal Bragg rod X-ray scattering

    International Nuclear Information System (INIS)

    Howes, P.B.; Rhead, S.; Roy, M.; Nicklin, C.L.; Rawle, J.L.; Norris, C.A.

    2013-01-01

    The atomic structure of the silicon Σ13(5 0 1) symmetric tilt grain boundary interface has been determined using Bragg rod X-ray scattering. In contrast to conventional structural studies of grain boundary structure using transmission electron microscopy, this approach allows the non-destructive measurement of macroscopic samples. The interface was found to have a single structure that is fully fourfold coordinated. X-ray diffraction data were measured at Beamline I07 at the Diamond Light Source

  7. Efficiency improvement of multicrystalline silicon solar cells after surface and grain boundaries passivation using vanadium oxide

    International Nuclear Information System (INIS)

    Derbali, L.; Ezzaouia, H.

    2012-01-01

    Highlights: ► Evaporation of vanadium pentoxide onto the front surface leads to reduce the surface reflectivity considerably. ► An efficient surface passivation can be obtained after thermal treatment of obtained films. ► Efficiency of the obtained solar cells has been improved noticeably after thermal treatment of deposited thin films. - Abstract: The aim of this work is to investigate the effect of vanadium oxide deposition onto the front surface of multicrystalline silicon (mc-Si) substrat, without any additional cost in the fabrication process and leading to an efficient surface and grain boundaries (GBs) passivation that have not been reported before. The lowest reflectance of mc-Si coated with vanadium oxide film of 9% was achieved by annealing the deposited film at 600 °C. Vanadium pentoxide (V 2 O 5 ) were thermally evaporated onto the surface of mc-Si substrates, followed by a short annealing duration at a temperature ranging between 600 °C and 800 °C, under O 2 atmosphere. The chemical composition of the films was analyzed by means of Fourier transform infrared spectroscopy (FTIR). Surface and cross-section morphology were determined by atomic force microscope (AFM) and a scanning electron microscope (SEM), respectively. The deposited vanadium oxide thin films make the possibility of combining in one processing step an antireflection coating deposition along with efficient surface state passivation, as compared to a reference wafer. Silicon solar cells based on untreated and treated mc-Si wafers were achieved. We showed that mc-silicon solar cells, subjected to the above treatment, have better short circuit currents and open-circuit voltages than those made from untreated wafers. Thus, the efficiency of obtained solar cells has been improved.

  8. Numerical study of the atomic and electronic structure of some silicon grain boundaries; Etude numerique de la structure atomique et electronique de quelques joints de grains du silicium

    Energy Technology Data Exchange (ETDEWEB)

    Torrent, M

    1996-07-01

    This work contributes to the theoretical study of extended defects in covalent materials. The study is especially devoted to the tilt grain boundaries in silicon as a model material. The theoretical model is based on the self-consistent tight-binding approximation and is applied within two numerical techniques: the fast 'order N' density-matrix method and the diagonalization technique which allows the sampling of the reciprocal space. Total energy parameters of the model have been fitted in order to reproduce the silicon band structure (with a correct gap value) and the transferability of crystalline and mechanical properties of this material. A new type of boundary conditions is proposed and tested. These conditions, named 'ante-periodic' or 'Moebius', allow only one grain boundary per box instead of two and decrease the CPU time by a factor of two. The model is then applied to the study of the {sigma}=25 [001] (710) grain boundary. The results show the possible presence in this boundary of low energy non-reconstructed atomic structures which are electrically active. This confirms what had been suggested by some experimental observations. The same study is also performed for the {sigma}=13 [001] (510) grain boundary. In order to compare the intrinsic electrical activity in the previous grain boundaries with the one induced by impurities, a total energy parametrization for the silicon-nickel bond is achieved and used in preliminary calculations. Finally the two variants of the {sigma}=11 [011] (2-33) interface are studied, especially their respective interfacial energies. The result disagrees with previous calculations using phenomenological potentials. (author)

  9. Energy dispersive spectroscopy analysis of aluminium segregation in silicon carbide grain boundaries.

    Science.gov (United States)

    Zhang, X F; Yang, Q; De Jonghe, L C; Zhang, Z

    2002-07-01

    The aluminium distribution in polycrystalline SiC hot-pressed with aluminium, boron and carbon additives was studied using X-ray energy-dispersive spectroscopy (EDS) and transmission electron microscopy (TEM). The Al excess in homophase SiC grain boundary films was determined, taking into account dissolved Al in the SiC lattice. In the spot-EDS analysis, an electron beam probe with a calibrated diameter was formed, and the total beam-specimen interaction volume was defined, taking the beam spreading through crystalline TEM foil into consideration. EDS spectra were collected from regions containing intergranular films and adjacent matrix grains, respectively. A theoretical treatment was presented and experimental errors were estimated, with a further discussion about the effects of foil thickness. Experimental examples are given, followed by statistical EDS analyses for grain boundary films in SiC samples hot-pressed with increased amounts of Al additions. The results demonstrated a substantial Al segregation in the nanometer-wide intergranular films in all samples. Al additions higher than 3 wt% saturated the Al concentrations in SiC grains and in grain boundary films. The effect of foil thickness, and the parameters for determining the optimum incident beam diameter in the EDS analysis are discussed.

  10. Effect of grain-boundary crystallization on the high-temperature strength of silicon nitride

    Science.gov (United States)

    Pierce, L. A.; Mieskowski, D. M.; Sanders, W. A.

    1986-01-01

    Si3N4 specimens having the composition 88.7 wt pct Si3N4-4.9 wt pct SiO2-6.4 wt pct Y2O3 were sintered at 2140 C under 25 atm N2 for 1 h and then subjected to a 5 h anneal at 1500 C. Crystallization of an amorphous grain-boundary phase resulted in the formation of Y2Si2O7. The short-time 1370 C strength of this material was compared with that of material of the same composition having no annealing treatment. No change in strength was noted. This is attributed to the refractory nature of the yttrium-rich grain-boundary phase (apparently identical in both glassy and crystalline phases) and the subsequent domination of the failure process by common processing flaws.

  11. Analysis of defect structure in silicon. Effect of grain boundary density on carrier mobility in UCP material

    Science.gov (United States)

    Dunn, J.; Stringfellow, G. B.; Natesh, R.

    1982-01-01

    The relationships between hole mobility and grain boundary density were studied. Mobility was measured using the van der Pauw technique, and grain boundary density was measured using a quantitative microscopy technique. Mobility was found to decrease with increasing grain boundary density.

  12. SILICON CARBIDE GRAIN BOUNDARY DISTRIBUTIONS, IRRADIATION CONDITIONS, AND SILVER RETENTION IN IRRADIATED AGR-1 TRISO FUEL PARTICLES

    Energy Technology Data Exchange (ETDEWEB)

    Lillo, T. M.; Rooyen, I. J.; Aguiar, J. A.

    2016-11-01

    Precession electron diffraction in the transmission electron microscope was used to map grain orientation and ultimately determine grain boundary misorientation angle distributions, relative fractions of grain boundary types (random high angle, low angle or coincident site lattice (CSL)-related boundaries) and the distributions of CSL-related grain boundaries in the SiC layer of irradiated TRISO-coated fuel particles. Two particles from the AGR-1 experiment exhibiting high Ag-110m retention (>80%) were compared to a particle exhibiting low Ag-110m retention (<19%). Irradiated particles with high Ag-110m retention exhibited a lower fraction of random, high angle grain boundaries compared to the low Ag-110m retention particle. An inverse relationship between the random, high angle grain boundary fraction and Ag-110m retention is found and is consistent with grain boundary percolation theory. Also, comparison of the grain boundary distributions with previously reported unirradiated grain boundary distributions, based on SEM-based EBSD for similarly fabricated particles, showed only small differences, i.e. a greater low angle grain boundary fraction in unirradiated SiC. It was, thus, concluded that SiC layers with grain boundary distributions susceptible to Ag-110m release were present prior to irradiation. Finally, irradiation parameters were found to have little effect on the association of fission product precipitates with specific grain boundary types.

  13. Effect of Grain Boundaries on the Performance of Thin-Film-Based Polycrystalline Silicon Solar Cells: A Numerical Modeling

    Science.gov (United States)

    Chhetri, Nikita; Chatterjee, Somenath

    2018-01-01

    Solar cells/photovoltaic, a renewable energy source, is appraised to be the most effective alternative to the conventional electrical energy generator. A cost-effective alternative of crystalline wafer-based solar cell is thin-film polycrystalline-based solar cell. This paper reports the numerical analysis of dependency of the solar cell parameters (i.e., efficiency, fill factor, open-circuit voltage and short-circuit current density) on grain size for thin-film-based polycrystalline silicon (Si) solar cells. A minority carrier lifetime model is proposed to do a correlation between the grains, grain boundaries and lifetime for thin-film-based polycrystalline Si solar cells in MATLAB environment. As observed, the increment in the grain size diameter results in increase in minority carrier lifetime in polycrystalline Si thin film. A non-equivalent series resistance double-diode model is used to find the dark as well as light (AM1.5) current-voltage (I-V) characteristics for thin-film-based polycrystalline Si solar cells. To optimize the effectiveness of the proposed model, a successive approximation method is used and the corresponding fitting parameters are obtained. The model is validated with the experimentally obtained results reported elsewhere. The experimentally reported solar cell parameters can be found using the proposed model described here.

  14. Three dimensional modelling of grain boundary interaction and evolution during directional solidification of multi-crystalline silicon

    Science.gov (United States)

    Jain, T.; Lin, H. K.; Lan, C. W.

    2018-03-01

    The development of grain structures during directional solidification of multi-crystalline silicon (mc-Si) plays a crucial role in the materials quality for silicon solar cells. Three dimensional (3D) modelling of the grain boundary (GB) interaction and evolution based on phase fields by considering anisotropic GB energy and mobility for mc-Si is carried out for the first time to elucidate the process. The energy and mobility of GBs are allowed to depend on misorientation and the GB plane. To examine the correctness of our method, the known the coincident site lattice (CSL) combinations such as (∑ a + ∑ b → ∑ a × b) or (∑ a + ∑ b → ∑ a / b) are verified. We frther discuss how to use the GB normal to characterize a ∑ 3 twin GB into a tilt or a twist one, and show the interaction between tilt and twist ∑ 3 twin GBs. Two experimental scenarios are considered for comparison and the results are in good agreement with the experiments as well as the theoretical predictions.

  15. Grain Boundary Complexions

    Science.gov (United States)

    2014-05-01

    complexion transitions occur often in doped titanates, such as BaTiO3 and SrTiO3, and have been utilized to tailor microstructural develop- ment [275,276...Cantwell et al. / Acta Materialia 62 (2014) 1–48 Despite decades of research, efforts to identify grain boundary complexion transitions in pure metals via...evidence suggesting grain boundary complexion transitions in pure metals has existed for decades. For example, researchers have reported anomalies and

  16. Final Technical Report: Grain Boundary Complexions and Transitions in Doped Silicon

    Energy Technology Data Exchange (ETDEWEB)

    Jian Luo

    2012-10-15

    This four-year research project has advanced the fundamental knowledge of grain boundary (GB) complexions (i.e., "two-dimensional interfacial phases") and associated GB "phase" transitions in several grounds. First, a bilayer interfacial phase, which had been directly observed by microscopy only in complex ceramic systems in prior studies, has been identified in simpler systems such as Au-doped Si and Bi-doped Ni in this study, where the interpretations of the their formation mechanisms and microscopic images are less equivocal. Second, convincing evidence for the existence of a first-order GB transition from a nominally "clean" GB to a bilayer adsorption interfacial phase has been revealed for Au-doped Si; the confirmation of the first-order nature of interfacial transitions at GBs, which was rare in prior studies, is scientifically significant and technologically important. Third, the bilayer interfacial phase discovered in Bi-doped Ni has been found to be the cause of the mysterious liquid metal embrittlement phenomenon in this system; the exact atomic level mechanism of this phenomenon has puzzled the materials and physics communities for over a century. Finally, significant advancements have been made to establish phenomenological thermodynamic models for GB complexions and transitions. Since GB complexions can control the transport, mechanical and physical properties of a broad range of metallic and ceramic materials, the fundamental knowledge generated by this project can have broad impacts on materials design in general. In this regard, understanding and controlling GB phase behaviors (complexions and transitions) can be an important component for the "Materials Genome" project.

  17. Characterization of grain growth, nature and role of grain boundaries in microcrystalline silicon – review of typical features

    Czech Academy of Sciences Publication Activity Database

    Kočka, Jan; Mates, Tomáš; Stuchlíková, The-Ha; Stuchlík, Jiří; Fejfar, Antonín

    2006-01-01

    Roč. 501, - (2006), s. 107-112 ISSN 0040-6090 R&D Projects: GA MŠk(CZ) ME 537; GA MŽP(CZ) SM/300/1/03; GA AV ČR(CZ) IAA1010316; GA AV ČR(CZ) IAA1010413 Institutional research plan: CEZ:AV0Z1010914 Keywords : microcrystalline silicon * growth * transport * hydrogen Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.666, year: 2006

  18. Grain Boundary Segregation in Metals

    CERN Document Server

    Lejcek, Pavel

    2010-01-01

    Grain boundaries are important structural components of polycrystalline materials used in the vast majority of technical applications. Because grain boundaries form a continuous network throughout such materials, their properties may limit their practical use. One of the serious phenomena which evoke these limitations is the grain boundary segregation of impurities. It results in the loss of grain boundary cohesion and consequently, in brittle fracture of the materials. The current book deals with fundamentals of grain boundary segregation in metallic materials and its relationship to the grain boundary structure, classification and other materials properties.

  19. Formation and characterization of high-performance silicon thin-film transistors with and without location-controlled grain boundary

    Science.gov (United States)

    Liao, Chan-Yu; Lin, Hsiao-Chun; Wang, Chao-Lung; Lee, I.-Che; Chou, Chia-Hsin; Li, Yu-Ren; Cheng, Huang-Chung

    2017-10-01

    This paper reports the demonstration of structural effects on excimer laser crystallization (ELC) for the Si strip with a recessed-channel structure on the silicon nitride under-layer (RCS-ULN). We revealed that a single location-controlled grain boundary (GB) oriented normal to the Si strip in the middle site without any other GB in the recessed region can be attained via ELC for the RCS-ULN structures with a short recessed region between neighboring long thick regions in a narrow Si strip. This can be attributed to the effective production of a significant 2D lateral thermal gradient in the recessed region and neighboring thick regions. Consequently, the RCS-ULN TFTs fabricated at the position one-half of such an optimal recessed region can achieve a superior field-effect mobility of 670 c{{m}2} {{V}-1}\\cdot {{s}-1} with minor performance variations since the single-crystal-like Si channel has been adopted.

  20. Grain boundary melting in ice

    OpenAIRE

    Thomson, E. S.; Hansen-Goos, Hendrik; Wilen, L. A.; Wettlaufer, J. S.

    2012-01-01

    We describe an optical scattering study of grain boundary premelting in water ice. Ubiquitous long ranged attractive polarization forces act to suppress grain boundary melting whereas repulsive forces originating in screened Coulomb interactions and classical colligative effects enhance it. The liquid enhancing effects can be manipulated by adding dopant ions to the system. For all measured grain boundaries this leads to increasing premelted film thickness with increasing electrolyte concentr...

  1. Grain boundary melting in ice

    Science.gov (United States)

    Thomson, E. S.; Hansen-Goos, Hendrik; Wettlaufer, J. S.; Wilen, L. A.

    2013-03-01

    We describe an optical scattering study of grain boundary premelting in water ice. Ubiquitous long ranged attractive polarization forces act to suppress grain boundary melting whereas repulsive forces originating in screened Coulomb interactions and classical colligative effects enhance it. The liquid enhancing effects can be manipulated by adding dopant ions to the system. For all measured grain boundaries this leads to increasing premelted film thickness with increasing electrolyte concentration. Although we understand that the interfacial surface charge densities qs and solute concentrations can potentially dominate the film thickness, we cannot directly measure them within a given grain boundary. Therefore, as a framework for interpreting the data we consider two appropriate qs dependent limits; one is dominated by the colligative effect and other is dominated by electrostatic interactions.

  2. On the elastic stiffness of grain boundaries

    International Nuclear Information System (INIS)

    Zhang Tongyi; Hack, J.E.

    1992-01-01

    The elastic softening of grain boundaries is evaluated from the starting point of grain boundary energy. Several examples are given to illustrate the relationship between boundary energy and the extent of softening. In general, a high grain boundary energy is associated with a large excess atomic volume in the boundary region. The consequent reduction in grain boundary stiffness can represent a significant fraction of that observed in bulk crystals. (orig.)

  3. Threshold voltage variation depending on single grain boundary and stored charges in an adjacent cell for vertical silicon–oxide–nitride–oxide–silicon NAND flash memory

    Science.gov (United States)

    Oh, Hyeongwan; Kim, Jiwon; Baek, Rock-Hyun; Lee, Jeong-Soo

    2018-04-01

    The effects of single grain boundary (SGB) position and stored electron charges in an adjacent cell in silicon–oxide–nitride–oxide–silicon (SONOS) structures on the variations of threshold voltage (V th) were investigated using technology computer-aided design (TCAD) simulation. As the bit line voltage increases, the SGB position causing the maximum V th variation was shifted from the center to the source side in the channel, owing to the drain-induced grain barrier lowering effect. When the SGB is located in the spacer region, the potential interaction from both the SGB and the stored electron charges in the adjacent cell becomes significant and thus resulting in larger V th variation. In contrast, when the SGB is located at the center of the channel, the peak position of potential barrier is shifted to the center, so that the influence of the adjacent cell is diminished. As the gate length is scaled down to 20 nm, the influence of stored charges in adjacent cells becomes significant, resulting in larger V th variations.

  4. Photoluminescence Imaging of Large-Grain CdTe for Grain Boundary Characterization

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, Steve; Allende Motz, Alyssa; Reese, Matthew O.; Burst, James M.; Metzger, Wyatt K.

    2015-06-14

    In this work, we use photoluminescence (PL) imaging to characterize CdTe grain boundary recombination. We use a silicon megapixel camera and green (532 nm) laser diodes for excitation. A microscope objective lens system is used for high spatial resolution and a field of view down to 190 um x 190 um. PL images of large-grain (5 to 50 um) CdTe samples show grain boundary and grain interior features that vary with processing conditions. PL images of samples in the as-deposited state show distinct dark grain boundaries that suggest high excess carrier recombination. A CdCl2 treatment leads to PL images with very little distinction at the grain boundaries, which illustrates the grain boundary passivation properties. Other process conditions are also shown, along with comparisons of PL images to high spatial resolution time-resolved PL carrier lifetime maps.

  5. Pressure effect on grain boundary diffusion

    International Nuclear Information System (INIS)

    Smirnova, E.S.; Chuvil'deev, V.N.

    1997-01-01

    The influence of hydrostatic pressure on grain boundary diffusion and grain boundary migration in metallic materials is theoretically investigated. The model is suggested that permits describing changes in activation energy of grain boundary self-diffusion and diffusion permeability of grain boundaries under hydrostatic pressure. The model is based on the ideas about island-type structure of grain boundaries as well as linear relationship of variations in grain boundary free volume to hydrostatic pressure value. Comparison of theoretical data with experimental ones for a number of metals and alloys (α-Zr, Sn-Ge, Cu-In with Co, In, Al as diffusing elements) shows a qualitative agreement

  6. Microscopic study of the H.sub.2./sub.O vapor treatment of the silicon grain boundaries

    Czech Academy of Sciences Publication Activity Database

    Honda, Shinya; Mates, Tomáš; Rezek, Bohuslav; Fejfar, Antonín; Kočka, Jan

    2008-01-01

    Roč. 354, č. 19-25 (2008), s. 2310-2313 ISSN 0022-3093 R&D Projects: GA MŽP(CZ) SN/3/172/05 Keywords : polycrystalline silicon films * H 2 O vapor treatment * potential * crystalline disorder * stress * defects * passivation Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.449, year: 2008

  7. Applied Thermodynamics: Grain Boundary Segregation

    Directory of Open Access Journals (Sweden)

    Pavel Lejček

    2014-03-01

    Full Text Available Chemical composition of interfaces—free surfaces and grain boundaries—is generally described by the Langmuir–McLean segregation isotherm controlled by Gibbs energy of segregation. Various components of the Gibbs energy of segregation, the standard and the excess ones as well as other thermodynamic state functions—enthalpy, entropy and volume—of interfacial segregation are derived and their physical meaning is elucidated. The importance of the thermodynamic state functions of grain boundary segregation, their dependence on volume solid solubility, mutual solute–solute interaction and pressure effect in ferrous alloys is demonstrated.

  8. Applied thermodynamics: Grain boundary segregation

    Czech Academy of Sciences Publication Activity Database

    Lejček, Pavel; Zheng, L.; Hofmann, S.; Šob, Mojmír

    2014-01-01

    Roč. 16, č. 3 (2014), s. 1462-1484 ISSN 1099-4300 R&D Projects: GA ČR(CZ) GAP108/12/0311; GA ČR GAP108/12/0144; GA MŠk(CZ) ED1.1.00/02.0068 Institutional support: RVO:68378271 ; RVO:68081723 Keywords : interfacial segregation * Gibbs energy of segregation * enthalpy * entropy * volume * grain boundaries * iron Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.502, year: 2014

  9. Transient Solute Drag in Migrating Grain Boundaries

    Czech Academy of Sciences Publication Activity Database

    Svoboda, Jiří; Fischer, F. D.; Liendl, M.

    2011-01-01

    Roč. 59, č. 17 (2011), s. 6556-6562 ISSN 1359-6454 R&D Projects: GA MŠk(CZ) OC10029 Institutional research plan: CEZ:AV0Z20410507 Keywords : Grain boundary diffusion * Grain boundary migration * Grain boundary segregation Subject RIV: BJ - Thermodynamic s Impact factor: 3.755, year: 2011

  10. Determination of grain boundary geometry using TEM

    NARCIS (Netherlands)

    Jang, H.; Farkas, D.; Hosson, J.T.M. De

    An experimental method to obtain the grain boundary geometry using the transmission electron microscope is presented. The method allows Σ determination including grain boundary plane orientation. In order to determine the specialness of the grain boundary, three different criteria for maximum

  11. Microscopic study of the H.sub.2./sub.O vapor treatment of the silicon grain boundaries

    Czech Academy of Sciences Publication Activity Database

    Honda, Shinya; Mates, Tomáš; Rezek, Bohuslav; Fejfar, Antonín; Kočka, Jan

    2008-01-01

    Roč. 354, č. 19-25 (2008), s. 2310-2313 ISSN 0022-3093 R&D Projects: GA MŠk(CZ) LC06040; GA AV ČR KAN400100701; GA ČR(CZ) GD202/05/H003; GA AV ČR IAA1010316; GA MŠk LC510; GA AV ČR IAA1010413; GA AV ČR KJB100100512; GA MŽP(CZ) SN/3/172/05 Institutional research plan: CEZ:AV0Z10100521 Keywords : polycrystalline silicon films * H 2 O vapor treatment * potential * crystalline disorder * stress * defects * passivation Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.449, year: 2008

  12. Grain Boundary Engineering of Electrodeposited Thin Films

    DEFF Research Database (Denmark)

    Alimadadi, Hossein

    Grain boundary engineering aims for a deliberate manipulation of the grain boundary characteristics to improve the properties of polycrystalline materials. Despite the emergence of some successful industrial applications, the mechanism(s) by which the boundary specific properties can be improved...... to engineer new materials. In this study, one of the most widely used electrolytes for electrodeposition is chosen for the synthesis of nickel films and based on thorough characterization of the boundaries the potentials in grain boundary engineering are outlined. The internal structure of the nickel films...... of the favorable boundaries that break the network of general grain boundaries. Successful dedicated synthesis of a textured nickel film fulfilling the requirements of grain boundary engineered materials, suggests improved boundary specific properties. However, the textured nickel film shows fairly low...

  13. Grain boundary segregation and intergranular failure

    International Nuclear Information System (INIS)

    White, C.L.

    1980-01-01

    Trace elements and impurities often segregate strongly to grain boundaries in metals and alloys. Concentrations of these elements at grain boundaries are often 10 3 to 10 5 times as great as their overall concentration in the alloy. Because of such segregation, certain trace elements can exert a disproportionate influence on material properties. One frequently observed consequence of trace element segregation to grain boundaries is the occurrence of grain boundary failure and low ductility. Less well known are incidences of improved ductility and inhibition of grain boundary fracture resulting from trace element segregation to grain boundaries in certain systems. An overview of trace element segregation and intergranular failure in a variety of alloy systems as well as preliminary results from studies on Al 3% Li will be presented

  14. Characterisation of multicrystalline silicon solar cells. Development of characterisation method for the combined effect of dislocations and grain boundaries on the minority carrier lifetime

    Energy Technology Data Exchange (ETDEWEB)

    Stokkan, Gaute

    2004-07-01

    The thesis has sections on theoretical background, mathematical models, experimental work such as lifetime measurements, dislocation density and grain boundary mapping, simulation of electrical activity mapping and conclusions and future work. Various mathematical models and nafion surface passivation are studied as well.

  15. Grain boundary corrosion of copper canister material

    International Nuclear Information System (INIS)

    Fennell, P.A.H.; Graham, A.J.; Smart, N.R.; Sofield, C.J.

    2001-03-01

    The proposed design for a final repository for spent fuel and other long-lived residues in Sweden is based on the multi-barrier principle. The waste will be encapsulated in sealed cylindrical canisters, which will then be placed in granite bedrock and surrounded by compacted bentonite clay. The canister design is based on a thick cast inner container fitted inside a corrosion-resistant copper canister. During fabrication of the outer copper canisters there will be some unavoidable grain growth in the welded areas. As grains grow they will tend to concentrate impurities within the copper at the new grain boundaries. The work described in this report was undertaken to determine whether there is any possibility of enhanced corrosion at grain boundaries within the copper canister. The potential for grain boundary corrosion was investigated by exposing copper specimens, which had undergone different heat treatments and hence had different grain sizes, to aerated artificial bentonite-equilibrated groundwater with two concentrations of chloride, for increasing periods of time. The degree of grain boundary corrosion was determined by atomic force microscopy (AFM) and optical microscopy. AFM showed no increase in grain boundary 'ditching' for low chloride groundwater. In high chloride groundwater the surface was covered uniformly with a fine-grained oxide. No increases in oxide thickness were observed. No significant grain boundary attack was observed using optical microscopy either. The work suggests that in aerated artificial groundwaters containing chloride ions, grain boundary corrosion of copper is unlikely to adversely affect SKB's copper canisters

  16. The Role of Grain Boundary Energy on Grain Boundary Complexion Transitions

    Energy Technology Data Exchange (ETDEWEB)

    Bojarski, Stephanie A. [Carnegie Mellon Univ., Pittsburgh, PA (United States). Dept. of Materials Science and Engineering; Rohrer, Gregory S. [Carnegie Mellon Univ., Pittsburgh, PA (United States). Dept. of Materials Science and Engineering

    2014-09-01

    Grain boundary complexions are distinct equilibrium structures and compositions of a grain boundary and complexion transformations are transition from a metastable to an equilibrium complexion at a specific thermodynamic and geometric conditions. Previous work indicates that, in the case of doped alumina, a complexion transition that increased the mobility of transformed boundaries and resulted in abnormal grain growth also caused a decrease in the mean relative grain boundary energy as well as an increase in the anisotropy of the grain boundary character distribution (GBCD). The current work will investigate the hypothesis that the rates of complexion transitions that result in abnormal grain growth (AGG) depend on grain boundary character and energy. Furthermore, the current work expands upon this understanding and tests the hypothesis that it is possible to control when and where a complexion transition occurs by controlling the local grain boundary energy distribution.

  17. Diffusion mechanisms in grain boundaries in solids

    International Nuclear Information System (INIS)

    Peterson, N.L.

    1982-01-01

    A critical review is given of our current knowledge of grain-boundary diffusion in solids. A pipe mechanism of diffusion based on the well-established dislocation model seems most appropriate for small-angle boundaries. Open channels, which have atomic configurations somewhat like dislocation cores, probably play a major role in large-angle grain-boundary diffusion. Dissociated dislocations and stacking faults are not efficient paths for grain-boundary diffusion. The diffusion and computer modeling experiments are consistent with a vacancy mechanism of diffusion by a rather well-localized vacancy. The effective width of a boundary for grain-boundary diffusion is about two atomic planes. These general features of grain-boundary diffusion, deduced primarily from experiments on metals, are thought to be equally applicable for pure ceramic solids. The ionic character of many ceramic oxides may cause some differences in grain-boundary structure from that observed in metals, resulting in changes in grain-boundary diffusion behavior. 72 references, 5 figures

  18. Ferroelectric domain continuity over grain boundaries

    DEFF Research Database (Denmark)

    Mantri, Sukriti; Oddershede, Jette; Damjanovic, Dragan

    2017-01-01

    Formation and mobility of domain walls in ferroelectric materials is responsible for many of their electrical and mechanical properties. Domain wall continuity across grain boundaries has been observed since the 1950's and is speculated to affect the grain boundary-domain interactions, thereby...... techniques in manipulating the micro-structure and domain structure to result in desired interactions between neighbouring grains could prove to be beneficial for future polycrystalline ferroelectric materials....

  19. Effects of grain size and grain boundaries on defect production in nanocrystalline 3C-SiC

    International Nuclear Information System (INIS)

    Swaminathan, N.; Kamenski, Paul J.; Morgan, Dane; Szlufarska, Izabela

    2010-01-01

    Cascade simulations in single crystal and nanocrystalline SiC have been conducted in order to determine the role of grain boundaries and grain size on defect production during primary radiation damage. Cascades are performed with 4 and 10 keV silicon as the primary knock-on atom (PKA). Total defect production is found to increase with decreasing grain size, and this effect is shown to be due to increased production in grain boundaries and changing grain boundary volume fraction. In order to consider in-grain defect production, a new mapping methodology is developed to properly normalize in-grain defect production rates for nanocrystalline materials. It is shown that the presence of grain boundaries does not affect the total normalized in-grain defect production significantly (the changes are lower than ∼20%) for the PKA energies considered. Defect production in the single grain containing the PKA is also studied and found to increase for smaller grain sizes. In particular, for smaller grain sizes the defect production decreases with increasing distance from the grain boundary while for larger grain sizes the presence of the grain boundaries has negligible effect on defect production. The results suggest that experimentally observed changes in radiation resistance of nanocrystalline materials may be due to long-term damage evolution rather than changes in defect production rates from primary damage.

  20. Equation of Motion for a Grain Boundary

    Science.gov (United States)

    Zhang, Luchan; Han, Jian; Xiang, Yang; Srolovitz, David J.

    2017-12-01

    Grain boundary (GB) migration controls many forms of microstructural evolution in polycrystalline materials. Recent theory, simulations, and experiments demonstrate that GB migration is controlled by the motion of discrete line defects or disconnections. We present a continuum equation of motion for grain boundary derived from the underlying discrete disconnection mechanism. We also present an equation of motion for the junctions where multiple grain boundaries meet—as is always the case in a polycrystal. The resulting equation of motion naturally exhibits junction drag—a widely observed phenomena in junction dynamics in solids and liquids.

  1. Grain boundary engineering of La{sub 0.7} Sr{sub 0.3} MnO{sub 3} films on silicon substrate: Scanning Tunneling Microscopy-Spectroscopy study

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, Anupama [Department of Applied Physics, Defence Institute of Advanced Technology (DU), Girinagar, Pune 411025 (India); Nori, Rajashree [Centre of Excellence in Nanoelectronics, Department of Electrical Engineering, Indian Institute of Technology (IIT Bombay), Mumbai 400076 (India); Dhobale, Sandip [Department of Applied Physics, Defence Institute of Advanced Technology (DU), Girinagar, Pune 411025 (India); Ramgopal Rao, V. [Centre of Excellence in Nanoelectronics, Department of Electrical Engineering, Indian Institute of Technology (IIT Bombay), Mumbai 400076 (India); Kale, S.N., E-mail: sangeetakale2004@gmail.com [Department of Applied Physics, Defence Institute of Advanced Technology (DU), Girinagar, Pune 411025 (India); Datar, Suwarna, E-mail: suwarna.datar@gmail.com [Department of Applied Physics, Defence Institute of Advanced Technology (DU), Girinagar, Pune 411025 (India)

    2014-09-01

    We employed a Scanning Tunnelling Microscope (STM) to study the surface topography and spatially resolved local electronic properties like local density of states (LDOS) of nanostructured films of La{sub 0.7} Sr{sub 0.3} MnO{sub 3} (LSMO). The nanostructured thin films of LSMO on silicon substrate were prepared using Pulsed Laser Deposition (PLD) technique. The deposition conditions were tuned to yield two different morphologies; one with uniform columnar closely packed islands and other with larger grain distribution in random fashion. The Scanning Tunnelling Spectroscopy (STS) revealed the extent of variation of density of states (DOS) near the Fermi level. From the spectroscopic features obtained we found the occurrence of phase separation between conducting and semiconducting domains and its possible correlation with the properties of the system. Semiconducting nature was observed at the grain boundaries, which could be extremely promising in futuristic nano-devices.

  2. Grain boundary structure and solute segregation in titanium-doped sapphire bicrystals

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Seth Thomas [Univ. of California, Berkeley, CA (United States)

    2002-01-01

    Solute segregation to ceramic grain boundaries governs material processing and microstructure evolution, and can strongly influence material properties critical to engineering performance. Understanding the evolution and implications of grain boundary chemistry is a vital component in the greater effort to engineer ceramics with controlled microstructures. This study examines solute segregation to engineered grain boundaries in titanium-doped sapphire (Al2O3) bicrystals, and explores relationships between grain boundary structure and chemistry at the nanometer scale using spectroscopic and imaging techniques in the transmission electron microscope (TEM). Results demonstrate dramatic changes in solute segregation stemming from small fluctuations in grain boundary plane and structure. Titanium and silicon solute species exhibit strong tendencies to segregate to non-basal and basal grain boundary planes, respectively. Evidence suggests that grain boundary faceting occurs in low-angle twis t boundaries to accommodate nonequilibrium solute segregation related to slow specimen cooling rates, while faceting of tilt grain boundaries often occurs to expose special planes of the coincidence site lattice (CSL). Moreover, quantitative analysis of grain boundary chemistry indicates preferential segregation of charged defects to grain boundary dislocations. These results offer direct proof that static dislocations in ionic materials can assume a net charge, and emphasize the importance of interactions between charged point, line, and planar defects in ionic materials. Efforts to understand grain boundary chemistry in terms of space charge theory, elastic misfit and nonequilibrium segregation are discussed for the Al2O3 system.

  3. Grain boundary structure and solute segregation in titanium-doped sapphire bicrystals

    International Nuclear Information System (INIS)

    Taylor, Seth T.

    2002-01-01

    Solute segregation to ceramic grain boundaries governs material processing and microstructure evolution, and can strongly influence material properties critical to engineering performance. Understanding the evolution and implications of grain boundary chemistry is a vital component in the greater effort to engineer ceramics with controlled microstructures. This study examines solute segregation to engineered grain boundaries in titanium-doped sapphire (Al2O3) bicrystals, and explores relationships between grain boundary structure and chemistry at the nanometer scale using spectroscopic and imaging techniques in the transmission electron microscope (TEM). Results demonstrate dramatic changes in solute segregation stemming from small fluctuations in grain boundary plane and structure. Titanium and silicon solute species exhibit strong tendencies to segregate to non-basal and basal grain boundary planes, respectively. Evidence suggests that grain boundary faceting occurs in low-angle twis t boundaries to accommodate nonequilibrium solute segregation related to slow specimen cooling rates, while faceting of tilt grain boundaries often occurs to expose special planes of the coincidence site lattice (CSL). Moreover, quantitative analysis of grain boundary chemistry indicates preferential segregation of charged defects to grain boundary dislocations. These results offer direct proof that static dislocations in ionic materials can assume a net charge, and emphasize the importance of interactions between charged point, line, and planar defects in ionic materials. Efforts to understand grain boundary chemistry in terms of space charge theory, elastic misfit and nonequilibrium segregation are discussed for the Al2O3 system

  4. Grain boundaries in Ni3Al. 2

    International Nuclear Information System (INIS)

    Kung, H.; Sass, S.L.

    1992-01-01

    This paper discusses the dislocation structure of small angle tilt and twist boundaries in ordered Ni 3 Al, with and without boron, investigated using transmission electron microscopy. Dislocation with Burgers vectors that correspond to anti-phase boundary (APB)-coupled superpartials were found in small angle twist boundaries in both boron-free and boron-doped Ni 3 Al, and a small angle tilt boundary in boron-doped Ni 3 Al. The boundary structures are in agreement with theoretical models proposed by Marcinkowski and co-workers. The APB energy determined from the dissociation of the grain boundary dislocations was lower than values reported for isolated APBs in Ni 3 Al. For small angle twist boundaries the presence of boron reduced the APB energy at the interface until it approached zero. This is consistent with the structure of these boundaries containing small regions of increased compositional disorder in the first atomic plane next to the interface

  5. Migration mechanisms of a faceted grain boundary

    Science.gov (United States)

    Hadian, R.; Grabowski, B.; Finnis, M. W.; Neugebauer, J.

    2018-04-01

    We report molecular dynamics simulations and their analysis for a mixed tilt and twist grain boundary vicinal to the Σ 7 symmetric tilt boundary of the type {1 2 3 } in aluminum. When minimized in energy at 0 K , a grain boundary of this type exhibits nanofacets that contain kinks. We observe that at higher temperatures of migration simulations, given extended annealing times, it is energetically favorable for these nanofacets to coalesce into a large terrace-facet structure. Therefore, we initiate the simulations from such a structure and study as a function of applied driving force and temperature how the boundary migrates. We find the migration of a faceted boundary can be described in terms of the flow of steps. The migration is dominated at lower driving force by the collective motion of the steps incorporated in the facet, and at higher driving forces by the step detachment from the terrace-facet junction and propagation of steps across the terraces. The velocity of steps on terraces is faster than their velocity when incorporated in the facet, and very much faster than the velocity of the facet profile itself, which is almost stationary. A simple kinetic Monte Carlo model matches the broad kinematic features revealed by the molecular dynamics. Since the mechanisms seem likely to be very general on kinked grain-boundary planes, the step-flow description is a promising approach to more quantitative modeling of general grain boundaries.

  6. Advantageous grain boundaries in iron pnictide superconductors.

    Science.gov (United States)

    Katase, Takayoshi; Ishimaru, Yoshihiro; Tsukamoto, Akira; Hiramatsu, Hidenori; Kamiya, Toshio; Tanabe, Keiichi; Hosono, Hideo

    2011-08-02

    High critical temperature superconductors have zero power consumption and could be used to produce ideal electric power lines. The principal obstacle in fabricating superconducting wires and tapes is grain boundaries-the misalignment of crystalline orientations at grain boundaries, which is unavoidable for polycrystals, largely deteriorates critical current density. Here we report that high critical temperature iron pnictide superconductors have advantages over cuprates with respect to these grain boundary issues. The transport properties through well-defined bicrystal grain boundary junctions with various misorientation angles (θ(GB)) were systematically investigated for cobalt-doped BaFe(2)As(2) (BaFe(2)As(2):Co) epitaxial films fabricated on bicrystal substrates. The critical current density through bicrystal grain boundary (J(c)(BGB)) remained high (>1 MA cm(-2)) and nearly constant up to a critical angle θ(c) of ∼9°, which is substantially larger than the θ(c) of ∼5° for YBa(2)Cu(3)O(7-δ). Even at θ(GB)>θ(c), the decay of J(c)(BGB) was much slower than that of YBa(2)Cu(3)O(7-δ).

  7. An Optical Study of Ice Grain Boundaries

    Science.gov (United States)

    Thomson, Erik S.

    The equilibrium phase geometry and evolution of polycrystals underlies the nature of materials. In particular, grain boundaries dominate the total interfacial area within polycrystalline materials. Our experimental studies are motivated by the importance of the structure, evolution, and thermodynamic behavior of grain boundaries near bulk melting temperatures. Ice is singled out as a material of interest due to its geophysical importance and its advantageous optical properties. An experimental apparatus and light reflection technique is designed to measure grain boundary melting in ice bicrystals, in thermodynamic equilibrium The technique allows continuous monitoring of reflected light intensity from the grain boundary as the temperature and solutal composition are systematically varied. For each sample the individual crystal orientations are also measured. The type and concentration of impurity in the liquid is controlled and the temperature is continuously recorded and controlled over a range near the melting point. An optical model of the interface is developed in order to convert experimental reflection data into a physical measurement of the liquidity of the grain boundary. Solutions are found for reflection and transmission amplitude coefficients for waves propagating from an arbitrarily oriented uniaxial anisotropic material into an isotropic material. This general model is used to determine solutions for three layer, ice/water/ice, systems with crystals of arbitrary orientation, and is broadly applicable to layered materials. Experimental results show thicker grain boundary liquid layers than expected from classical colligative effects. A physically realistic model of intermolecular interactions succeeds in bounding the measurements. These measurements may have important implications for understanding a wide range of effects in polycrystalline materials. Likewise, the experimental techniques and optical theory may be applied to other systems of broad

  8. Grain boundary disordering just before partial melting

    Science.gov (United States)

    Takei, Y.

    2017-12-01

    Recent experimental studies by using a rock analogue (organic polycrystals) have shown that significant enhancement of anelastic relaxation and steady-state creep in the partially molten aggregates starts from considerably below the solidus temperature in the absence of melt (Takei et al, 2014; Yamauchi & Takei, 2016, JGR). These results suggest that melt is not necessary to explain the seismic low velocity, high attenuation, and weak viscosity regions in the upper mantle. Indeed, Priestley & McKenzie (2006, 2013, EPSL) captured a steep reduction of seismic Vs just below the dry peridotite solidus, which was explained well by the empirical model of Yamauchi & Takei (2016). In spite of many geophysical implications (Takei, 2017, Ann. Rev. EPS, in press), however, underlying physics for the mechanical weakening just before partial melting remains unclear. The purpose of this study is to develop a physical model. Anelasticity and viscosity measured by Yamauchi & Takei (2016) are both rate-controlled by grain-boundary diffusion. Therefore, their observations suggest that the dynamic properties of grain boundary change just before partial melting. Significant disordering of grain boundary just before partial melting has been predicted theoretically in the area of material sciences (sometimes called `pre-melting'). I will summarize the thermodynamic models of grain boundary developed in these studies, and compare the predictions of these models to the experimental observations by Yamauchi & Takei (2016). Using these models, I will also clarify a relationship between grain-boundary disordering and grain-boundary wetting, and a different behavior between pure and binary systems in pre-melting. Acknowledgement: I thank R. Cooper for letting me know about the theoretical studies of pre-melting in binary eutectic system.

  9. Grain Boundaries From Theory to Engineering

    CERN Document Server

    Priester, Louisette

    2013-01-01

    Grain boundaries are a main feature of crystalline materials. They play a key role in determining the properties of materials, especially when grain size decreases and even more so with the current improvements of  processing tools and methods that allow us to control various elements in a polycrystal. This book presents the theoretical basis of the study of  grain boundaries and aims to open up new lines of research in this area. The treatment is light on mathematical approaches while emphasizing practical examples; the issues they raise are discussed with reference to theories. The general approach of the book has two main goals: to lead the reader from the concept of ‘ideal’ to ‘real’ grain boundaries; to depart from established knowledge and address the opportunities emerging through "grain boundary engineering",  the control of morphological and crystallographic features that affect material properties. The book is divided in three parts:  I ‘From interganular order to disorder’ deals wit...

  10. Grain boundary atomic structure and properties

    Czech Academy of Sciences Publication Activity Database

    Paidar, Václav

    2002-01-01

    Roč. 8, - (2002), s. 24-30 ISSN 1335-1532 R&D Projects: GA ČR GA202/02/0916 Institutional research plan: CEZ:AV0Z1010914 Keywords : atomic structures * grain boundary properties * phase transformations Subject RIV: BM - Solid Matter Physics ; Magnetism

  11. Structures and transitions in tungsten grain boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Frolov, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zhu, Q. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Marian, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Rudd, R. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-02-07

    The objective of this study is to develop a computational methodology to predict structure, energies of tungsten grain boundaries as a function of misorientation and inclination. The energies and the mobilities are the necessary input for thermomechanical model of recrystallization of tungsten for magnetic fusion applications being developed by the Marian Group at UCLA.

  12. Grain boundary effects in nanocrystalline diamond

    Czech Academy of Sciences Publication Activity Database

    Mareš, Jiří J.; Hubík, Pavel; Krištofik, Jozef; Nesládek, Miloš

    2008-01-01

    Roč. 205, č. 9 (2008), 2163-2168 ISSN 1862-6300 R&D Projects: GA ČR(CZ) GA202/06/0040 Institutional research plan: CEZ:AV0Z10100521 Keywords : diamond film * grain boundary * superconductivity * noise * ballistic transport Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.205, year: 2008

  13. Interactions between Dislocations and Grain Boundaries

    NARCIS (Netherlands)

    Soer, Wouter Anthon

    2006-01-01

    Dislocations (line defects) and grain boundaries (planar defects) are two types of lattice defects that are crucial to the deformation behavior of metals. Permanent deformation of a crystalline material is microscopically associated with the nucleation and propagation of dislocations, and extensive

  14. Niobium segregation in the austenitic grain boundary

    International Nuclear Information System (INIS)

    Mei, P.R.; Farah, E.A.

    1984-01-01

    The segregation of niobium and carbon in the boundary of the old austenitic grain (martensitic sample) of a steel 0,4%C/0,03%Nb, homogenized in 1350 0 C for one hour, with the help of the ionic microprobe, using oxygen as primary beam, is studied. The niobium segregation in Fe /0,58Nb homogenized samples at 1300 0 C by 8 hours and cooled in water, using the electronic microprobe is also studied. (E.G.) [pt

  15. Positron annihilation at grain boundaries in metals

    Czech Academy of Sciences Publication Activity Database

    Kuriplach, J.; Melikhova, O.; Hou, M.; Van Petegem, S.; Zhurkin, E.; Šob, Mojmír

    2007-01-01

    Roč. 4, č. 10 (2007), s. 3461-3464 ISSN 1862-6351. [International Conference on Positron Annihilation /14./. Hamilton, Ontario, 23.07.2006-28.07.2006] R&D Projects: GA AV ČR IAA1041302; GA MŠk OC 147 Institutional research plan: CEZ:AV0Z20410507 Keywords : positron annihilation * grain boundaries * electronic structure Subject RIV: BM - Solid Matter Physics ; Magnetism

  16. Recombination activity of grain boundaries in high-performance multicrystalline Si during solar cell processing

    Science.gov (United States)

    Adamczyk, Krzysztof; Søndenâ, Rune; Stokkan, Gaute; Looney, Erin; Jensen, Mallory; Lai, Barry; Rinio, Markus; Di Sabatino, Marisa

    2018-02-01

    In this work, we applied internal quantum efficiency mapping to study the recombination activity of grain boundaries in High Performance Multicrystalline Silicon under different processing conditions. Wafers were divided into groups and underwent different thermal processing, consisting of phosphorus diffusion gettering and surface passivation with hydrogen rich layers. After these thermal treatments, wafers were processed into heterojunction with intrinsic thin layer solar cells. Light Beam Induced Current and Electron Backscatter Diffraction were applied to analyse the influence of thermal treatment during standard solar cell processing on different types of grain boundaries. The results show that after cell processing, most random-angle grain boundaries in the material are well passivated, but small-angle grain boundaries are not well passivated. Special cases of coincidence site lattice grain boundaries with high recombination activity are also found. Based on micro-X-ray fluorescence measurements, a change in the contamination level is suggested as the reason behind their increased activity.

  17. Studies about diffusion through grain boundary

    International Nuclear Information System (INIS)

    Allevato, C.E.

    1983-01-01

    Samples with layers of gold-silver and silver-chromium were deposited in high vacuum (10 -5 -10 -6 Torr) on glass and sodium chloride substrates. After deposition, these films were annealed at different temperatures and analysed by Rutherford Backscattering, Auger Spesctroscopy and Transmission Electron Microscopy. A simulated convolution was done using a computer in order to evalute the precision of the particle detector employed in the backscattering. The concentration profiles used to determine the diffusion coefficient were obtained by Auger electron spectroscopy. This technique demanded a study of sputtering rate to convert time of sputtering in thickness. This rate was determined by two methods. Analyses of the samples of silver-chromium, heated up to 250 0 C, by transmission electron microscopy and Auger electron spectroscopy, indicated the presence of oxide in small isolated regions, as crystallites. Values of the diffusion coefficient and activation energy related to the diffusion through the volume and by the grain boundary were determined by Suzuoka's method. The system Ag/Cr, due to its high grain boundary density, led to an increase of the diffusion coefficient so that this coefficient and the activation energy were obtained only from the grain boundary. (Author) [pt

  18. Single Grain Boundary Modeling and Design of Microcrystalline Si Solar Cells

    OpenAIRE

    Lin, Chu-Hsuan; Hsu, Wen-Tzu; Tai, Cheng-Hung

    2013-01-01

    For photovoltaic applications, microcrystalline silicon has a lot of advantages, such as the ability to absorb the near-infrared part of the solar spectrum. However, there are many dangling bonds at the grain boundary in microcrystalline Si. These dangling bonds would lead to the recombination of photo-generated carriers and decrease the conversion efficiency. Therefore, we included the grain boundary in the numerical study in order to simulate a microcrystalline Si solar cell accurately, des...

  19. Plasticity-induced restructuring of a nanocrystalline grain boundary network

    International Nuclear Information System (INIS)

    Panzarino, Jason F.; Pan, Zhiliang; Rupert, Timothy J.

    2016-01-01

    The grain boundary-mediated mechanisms that control plastic deformation of nanocrystalline metals should cause evolution of the grain boundary network, since they directly alter misorientation relationships between crystals. Unfortunately, current experimental techniques are unable to track such evolution, due to limits on both spatial and temporal resolution. In this work, molecular dynamics simulations are used to study grain boundary restructuring in nanocrystalline Al during both monotonic tension and cyclic loading. This task is enabled by the creation of new analysis tools for atomistic datasets that allow for a complete characterization and tracking of microstructural descriptors of the grain boundary network. Quantitative measurements of grain boundary character distribution, triple junction type, grain boundary plane normal, and other interfacial network characteristics are extracted and analyzed. The results presented here show that nanocrystalline plasticity leads to an increase in special boundary fraction and disruption of two-dimensional boundary connectivity, with the most dramatic evolution occurring in the smallest grain sizes.

  20. HREM of general and twist grain boundaries.

    Energy Technology Data Exchange (ETDEWEB)

    Merkle, K. L.; Thompson, L. J.

    1999-03-10

    The observation of atomic-scale structures of grain boundaries (GBs) via axial illumination HREM has been largely restricted to tilt GBs, due to the requirement that the electron beam be parallel to a low-index zone axis on both sides of the interface. This condition can be fulfilled for all tilt GBs with disorientation about a low-index direction. The information obtained through HREM studies in many materials has brought important insights concerning the atomic-scale structure of such boundaries. However, it is well known that tilt GBs occupy only an infinitesimally small fraction of the 5-dimensional phase space which describes the macroscopic geometry of all GBs. Therefore, although tilt GBs are very important due to their low energy, it would be useful to also study twist GBs and general GBs that contain twist and tilt components.

  1. The relationship between grain boundary structure, defect mobility, and grain boundary sink efficiency

    Science.gov (United States)

    Uberuaga, Blas Pedro; Vernon, Louis J.; Martinez, Enrique; Voter, Arthur F.

    2015-01-01

    Nanocrystalline materials have received great attention due to their potential for improved functionality and have been proposed for extreme environments where the interfaces are expected to promote radiation tolerance. However, the precise role of the interfaces in modifying defect behavior is unclear. Using long-time simulations methods, we determine the mobility of defects and defect clusters at grain boundaries in Cu. We find that mobilities vary significantly with boundary structure and cluster size, with larger clusters exhibiting reduced mobility, and that interface sink efficiency depends on the kinetics of defects within the interface via the in-boundary annihilation rate of defects. Thus, sink efficiency is a strong function of defect mobility, which depends on boundary structure, a property that evolves with time. Further, defect mobility at boundaries can be slower than in the bulk, which has general implications for the properties of polycrystalline materials. Finally, we correlate defect energetics with the volumes of atomic sites at the boundary. PMID:25766999

  2. Grain-boundary engineering applied to grain growth in a high temperature material

    International Nuclear Information System (INIS)

    Huda, Z.

    1993-01-01

    Crystallography of grain boundaries are determined for a high temperature material, before and after grain growth processes, so as to study the induction of special properties useful for application in components of a gas-turbine engine. The philosophy of grain-boundary engineering is applied to grain growth in APK-6, a powder formed nickel-base superalloy so as to establish the possible structure/property relationships. The alloy in the as received condition is shown to possess a strong texture and contained coincident site lattices (CSL) boundaries with most boundaries having sigma values in the range of 3 > sigma > 25. A normal grain-growth heat treatment result in a good population of low angle grain boundaries, and drastically reduces the proportion of CSL boundaries. A strong [011] annealing texture is observed after an intermediate grain growth; most grain boundaries, here, tend to be high angle indicating a possibility of possessing special properties. (author)

  3. Mathematical simulation of point defect interaction with grain boundaries

    International Nuclear Information System (INIS)

    Bojko, V.S.

    1987-01-01

    Published works, where the interaction of point defects and grain boundaries was studied by mathematical simulation methods, have been analysed. Energetics of the vacancy formation both in nuclei of large-angle special grain boundaries and in lattice regions adjoining them has been considered. The data obtained permit to explain specific features of grain-boundary diffusion processes. Results of mathematical simulation of the interaction of impurity atoms and boundaries have been considered. Specific features of the helium atom interaction with large-angle grain boundaries are analysed as well

  4. Additive recovery at lateral boundaries of grains under electronic exposure

    International Nuclear Information System (INIS)

    Plotnikov, S.V.; Postnikov, D.V.

    2000-01-01

    The experimental investigation of additive re-distribution under electronic beam revealed a recovery of the additive at grain boundaries. Additive accumulation mainly takes place at the boundaries that are perpendicular to material surface, whereas there is no an observed recovery of additive at the boundaries that are parallel to the surface. To construe the processes of additive recovery at grain boundaries, we may use the kinetic diffusion equation describing the mass transfer processes in the presence of temperature gradients and non-equilibrium vacancies. The additive recovery is caused by spot fault gradients near the grain boundary. The grain boundary is an intensive run-off region of vacancies. Therefore, the average vacancy distribution profile near the grain boundary changes its pattern. The above case indicates that there are two additive fluxes. One of them is vectored perpendicular to the surface, and the other one is parallel to it, i.e. it is vectored to the grain boundary. A study of the perpendicular and parallel boundaries shows that there is no additive settling at the boundaries that are parallel to the surface, since the general flux is vectored to the parallel boundaries. There is no such kind of phenomenon at the grain boundaries that are perpendicular to the surface. Besides, the perpendicular boundaries are more effective run-off regions for vacancies, since there is a slower build-up of the region with vacancies due to displacement of the vacancies to the surface

  5. Grain boundary and triple junction diffusion in nanocrystalline copper

    Energy Technology Data Exchange (ETDEWEB)

    Wegner, M., E-mail: m.wegner@uni-muenster.de; Leuthold, J.; Peterlechner, M.; Divinski, S. V., E-mail: divin@uni-muenster.de [Institut für Materialphysik, Universität Münster, Wilhelm-Klemm-Straße 10, D-48149, Münster (Germany); Song, X., E-mail: xysong@bjut.edu.cn [College of Materials Science and Engineering, Beijing University of Technology, 100124 Beijing (China); Wilde, G. [Institut für Materialphysik, Universität Münster, Wilhelm-Klemm-Straße 10, D-48149, Münster (Germany); Institute of Nanochemistry and Nanobiology, School of Environmental and Chemical Engineering, Shanghai University, 200444 Shanghai (China)

    2014-09-07

    Grain boundary and triple junction diffusion in nanocrystalline Cu samples with grain sizes, 〈d〉, of ∼35 and ∼44 nm produced by spark plasma sintering were investigated by the radiotracer method using the {sup 63}Ni isotope. The measured diffusivities, D{sub eff}, are comparable with those determined previously for Ni grain boundary diffusion in well-annealed, high purity, coarse grained, polycrystalline copper, substantiating the absence of a grain size effect on the kinetic properties of grain boundaries in a nanocrystalline material at grain sizes d ≥ 35 nm. Simultaneously, the analysis predicts that if triple junction diffusion of Ni in Cu is enhanced with respect to the corresponding grain boundary diffusion rate, it is still less than 500⋅D{sub gb} within the temperature interval from 420 K to 470 K.

  6. Data Pipeline Development for Grain Boundary Structures Classification

    OpenAIRE

    Li, Bingxi

    2017-01-01

    Grain Boundaries govern many properties of polycrystalline materials, including the vast majority of engineering materials. Evolutionary algorithm can be applied to predict the grain boundary structures in different systems. However, the recognition and classification of thousands of predicted structures is a very challenging work for eye detection in terms of efficiency and accuracy. A data pipeline is developed to accelerate the classification and recognition of grain boundary structures pr...

  7. Competing Grain Boundary and Interior Deformation Mechanisms with Varying Sizes

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Wei [University of Tennessee (UT); Gao, Yanfei [ORNL; Nieh, T. G. [University of Tennessee, Knoxville (UTK)

    2018-01-01

    In typical coarse-grained alloys, the dominant plastic deformations are dislocation gliding or climbing, and material strengths can be tuned by dislocation interactions with grain boundaries, precipitates, solid solutions, and other defects. With the reduction of grain size, the increase of material strengths follows the classic Hall-Petch relationship up to nano-grained materials. Even at room temperatures, nano-grained materials exhibit strength softening, or called the inverse Hall-Petch effect, as grain boundary processes take over as the dominant deformation mechanisms. On the other hand, at elevated temperatures, grain boundary processes compete with grain interior deformation mechanisms over a wide range of the applied stress and grain sizes. This book chapter reviews and compares the rate equation model and the microstructure-based finite element simulations. The latter explicitly accounts for the grain boundary sliding, grain boundary diffusion and migration, as well as the grain interior dislocation creep. Therefore the explicit finite element method has clear advantages in problems where microstructural heterogeneities play a critical role, such as in the gradient microstructure in shot peening or weldment. Furthermore, combined with the Hall-Petch effect and its breakdown, the above competing processes help construct deformation mechanism maps by extending from the classic Frost-Ashby type to the ones with the dependence of grain size.

  8. Evolution of grain boundary character distributions in alloy 825 tubes during high temperature annealing: Is grain boundary engineering achieved through recrystallization or grain growth?

    International Nuclear Information System (INIS)

    Bai, Qin; Zhao, Qing; Xia, Shuang; Wang, Baoshun; Zhou, Bangxin; Su, Cheng

    2017-01-01

    Grain boundary engineering (GBE) of nickel-based alloy 825 tubes was carried out with different cold drawing deformations by using a draw-bench on a factory production line and subsequent annealing at various temperatures. The microstructure evolution of alloy 825 during thermal-mechanical processing (TMP) was characterized by means of the electron backscatter diffraction (EBSD) technique to study the TMP effects on the grain boundary network and the evolution of grain boundary character distributions during high temperature annealing. The results showed that the proportion of ∑ 3 n coincidence site lattice (CSL) boundaries of alloy 825 tubes could be increased to > 75% by the TMP of 5% cold drawing and subsequent annealing at 1050 °C for 10 min. The microstructures of the partially recrystallized samples and the fully recrystallized samples suggested that the proportion of low ∑ CSL grain boundaries depended on the annealing time. The frequency of low ∑ CSL grain boundaries increases rapidly with increasing annealing time associating with the formation of large-size highly-twinned grains-cluster microstructure during recrystallization. However, upon further increasing annealing time, the frequency of low ∑ CSL grain boundaries decreased markedly during grain growth. So it is concluded that grain boundary engineering is achieved through recrystallization rather than grain growth. - Highlights: •The grain boundary engineering (GBE) is applicable to 825 tubes. •GBE is achieved through recrystallization rather than grain growth. •The low ∑ CSL grain boundaries in 825 tubes can be increased to > 75%.

  9. Absence of grain boundary melting in solid helium

    Energy Technology Data Exchange (ETDEWEB)

    Caupin, Frederic; Sasaki, Satoshi; Balibar, Sebastien [Laboratoire de Physique Statistique de l' Ecole Normale Superieure, associe au CNRS et aux Universites Paris 6 et 7, 24 rue Lhomond, 75005 Paris (France)], E-mail: caupin@lps.ens.fr

    2008-12-10

    Crystals are often expected to start melting at their free surface or at the interface between grains. Grain boundary melting corresponds to the situation where the interface between grains is invaded by a thick liquid film at the bulk melting temperature T{sub m}. In some cases, premelting is predicted, with liquid-like layers appearing between grains at temperatures below T{sub m}. We review this topic, and describe our experiments on solid helium 4. We find that grain boundaries are not wetted by the liquid at T{sub m}: they emerge at the liquid-solid interface with a non-zero contact angle. This is consistent with a general argument which predicts that, although systems with short-range forces might show grain boundary melting and premelting, in systems with long-range forces (like helium), grain boundaries can only be wetted incompletely by the liquid at T{sub m}.

  10. The effect of grain boundary chemistry on the slip transmission process through grain boundaries in Ni3Al

    International Nuclear Information System (INIS)

    Robertson, I.M.; Lee, T.C.; Subramanian, R.; Birnbaum, H.K.

    1992-01-01

    This paper reports on the conditions established in disordered FCC systems for predicting the slip system that will be activated by a grain boundary to relieve a local stress concentration that have been applied to the ordered FCC alloy Ni 3 Al. The slip transfer behavior in hypo-stoichiometric Ni 3 Al with (0.2 at. %B) and without boron was directly observed by performing the deformation experiments in situ in the transmission electron microscope. In the boron-free and boron-doped alloys, lattice dislocations were incorporated in the grain boundary, but did not show evidence of dissociation to grain boundary dislocations or of movement in the grain boundary plane. The stress concentration associated with the dislocation pileup at the grain boundary are relieved by the emission of dislocations from the grain boundary in the boron-doped alloy. The slip system initiated in the adjoining grain obeyed the conditions established for disordered FCC systems. In the boron-free alloy, the primary stress relief mechanism was grain-boundary cracking, although dislocation emission from the grain boundary also occurred and accompanied intergranular crack advance

  11. Grain boundary strength as point defect sink strength

    International Nuclear Information System (INIS)

    Volobuev, A.V.; Gann, V.V.

    1987-01-01

    Sink strength of spherical grain boundary as an absolutely absorbing surface and as finite thickness wall consisting of the edge dislocations are considered. The values of the grain boundary sink strength are shown to be critically dependent on the point defect recombination degree

  12. Additive recovery of lateral boundaries of grains under electronic exposure

    International Nuclear Information System (INIS)

    Postnikov, D.V.; Plotnikov, S.V.

    2002-01-01

    The experimental investigation of additive re-distribution under electronic beam revealed a recovery of the additive at grain boundaries. Additive accumulation mainly takes place at the boundaries that are perpendicular to material surface, whereas there is no an observed recovery of additive at the boundaries that are parallel to the surface. The additive recovery is caused by spot fault gradients near the grain boundary. The grain boundary is an intensive run-off region of vacancies. Therefore, the average vacancy distribution profile near the grain boundary changes its pattern. The above case indicates that there are two additive fluxes. One of them is vectored perpendicular to the surface, and the other one is parallel to it, i. e. it is vectored to the grain boundary. A study of the perpendicular and parallel boundaries shows that there is no additive settling at the boundaries that are parallel to the surface, since the general flux is vectored to the parallel boundaries. There is no such kind of phenomenon at the grain boundaries that are perpendicular to the surface. Besides, the perpendicular boundaries are more effective run-off regions for vacancies, since there is a slower build-up of the region with vacancies due to displacement of the vacancies to the surface. To compute concentration of vacancies we will consider a grain of the surface as a model. The computations indicate the presence of vacancy gradients vectored to the surface and grain boundaries, which are perpendicular to the surface. Comparison of the experimental and theoretical outcomes shows a good agreement between the theoretical model and actual processes occurring under the exposure. This theory disclose wide potentials for application of diffusion processes in alloys

  13. A grain boundary phase transition in Si–Au

    International Nuclear Information System (INIS)

    Ma, Shuailei; Meshinchi Asl, Kaveh; Tansarawiput, Chookiat; Cantwell, Patrick R.; Qi, Minghao; Harmer, Martin P.; Luo, Jian

    2012-01-01

    A grain boundary transition from a bilayer to an intrinsic (nominally clean) boundary is observed in Si–Au. An atomically abrupt transition between the two complexions (grain boundary stabilized phases) implies the occurrence of a first-order interfacial phase transition associated with a discontinuity in the interfacial excess. This observation supports a grain-boundary complexion theory with broad applications. This transition is atypical in that the monolayer complexion is absent. A model is proposed to explain the bilayer stabilization and the origin of this complexion transition.

  14. The origin of grain boundary capacitance in highly doped ceria.

    Science.gov (United States)

    Souza, Eduardo Caetano C; Goodenough, John B

    2016-02-17

    The origin of a grain-boundary capacitance in mixed oxide-ion/electronic conductors has been investigated for the case of Ce0.8Sm0.2O1.9-δ using a.c. impedance spectroscopy under low pO2 from 250 to 400 °C. The observed capacitance is interpreted in terms of Ce(III):4f(1) electrons first introduced into the grains and not into the grain boundaries.

  15. Process for preparing fine grain silicon carbide powder

    Science.gov (United States)

    Wei, G.C.

    Method of producing fine-grain silicon carbide powder comprises combining methyltrimethoxysilane with a solution of phenolic resin, acetone and water or sugar and water, gelling the resulting mixture, and then drying and heating the obtained gel.

  16. Temperature dependence of grain boundary free energy and elastic constants

    International Nuclear Information System (INIS)

    Foiles, Stephen M.

    2010-01-01

    This work explores the suggestion that the temperature dependence of the grain boundary free energy can be estimated from the temperature dependence of the elastic constants. The temperature-dependent elastic constants and free energy of a symmetric Σ79 tilt boundary are computed for an embedded atom method model of Ni. The grain boundary free energy scales with the product of the shear modulus times the lattice constant for temperatures up to about 0.75 the melting temperature.

  17. Modelling of grain refinement driven by negative grain boundary energy

    Czech Academy of Sciences Publication Activity Database

    Fischer, F. D.; Zickler, G. A.; Svoboda, Jiří

    2017-01-01

    Roč. 97, č. 23 (2017), s. 1963-1977 ISSN 1478-6435 R&D Projects: GA ČR(CZ) GA15-06390S Institutional support: RVO:68081723 Keywords : grain refinement * grain nucleation * distribution concept * jump on distribution function Subject RIV: BJ - Thermodynamics OBOR OECD: Thermodynamics Impact factor: 1.505, year: 2016

  18. Grain boundary character distributions of coincidence site lattice boundaries in WC-Co composites with different WC grain sizes

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Xiaokun, E-mail: yuanxiaokun@bjut.edu.cn

    2013-12-05

    Highlights: •GBCDs of two kinds of CSL boundaries in cemented carbides are examined. •Carbide mean grain size is determinant in controlling the populations of CSL boundaries. •Rapid decrease of sigma2 boundaries occurs at higher speed than the coarsening of carbide grains. -- Abstract: The grain boundary character distributions of sigma2 and sigma13 boundaries were investigated in cemented carbide samples with different carbide grain sizes. Samples were prepared with average carbide grain sizes of about 0.5 μm, 1 μm and 2 μm, respectively. The electron backscattered diffraction measurements show that with the increase of the carbide grain size, populations of both sigma2 and sigma13 boundaries decrease; in the meantime, the sigma2 twist and sigma13 twist boundaries keep as the most common boundary types. The results suggest that the carbide grain size could be determinant in controlling the populations of coincidence site lattice boundaries in WC-Co composites.

  19. A constitutive model of nanocrystalline metals based on competing grain boundary and grain interior deformation mechanisms

    KAUST Repository

    Gurses, Ercan

    2011-12-01

    In this work, a viscoplastic constitutive model for nanocrystalline metals is presented. The model is based on competing grain boundary and grain interior deformation mechanisms. In particular, inelastic deformations caused by grain boundary diffusion, grain boundary sliding and dislocation activities are considered. Effects of pressure on the grain boundary diffusion and sliding mechanisms are taken into account. Furthermore, the influence of grain size distribution on macroscopic response is studied. The model is shown to capture the fundamental mechanical characteristics of nanocrystalline metals. These include grain size dependence of the strength, i.e., both the traditional and the inverse Hall-Petch effects, the tension-compression asymmetry and the enhanced rate sensitivity. © 2011 Elsevier B.V. All rights reserved.

  20. Grain-boundary migration in metals fatigued at high temperatures

    International Nuclear Information System (INIS)

    Snowden, K.U.; Stathers, P.A.; Hughes, D.S.

    1976-01-01

    It is stated that grain boundary migration in polycrystalline metals fatigued at high temperatures has been reported for FCC, BCC, and CPH metals. The migration results in a 'diamond' or orthogonal configuration of boundaries with segments aligned in the maximum sheer stress directions. It has been suggested that this migration contributes to grain boundary failure by the absorption of point defects at migrating boundaries and/or by the development of the 'diamond' configuration, which puts the boundaries in a favourable arrangement for sliding. There seems, however, to be little qualitative information on grain boundary migration under these conditions. The results are here reported of studies on grain boundary migration in Al, Cu, Zr and Zircaloy-2 specimens fatigued at temperatures where grain boundary cavitation occurs. These results indicate that during the initial 10% of the fatigue life the rate of boundary migration decreases with time and the amount of migration varies with tsup(2/3). The possible influence of boundary migration on cavitation is suggested to be limited to the initial part of the fatigue life. Mechanisms are discussed. (U.K.)

  1. Science at the interface : grain boundaries in nanocrystalline metals.

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, Mark Andrew; Follstaedt, David Martin; Knapp, James Arthur; Brewer, Luke N.; Holm, Elizabeth Ann; Foiles, Stephen Martin; Hattar, Khalid M.; Clark, Blythe B.; Olmsted, David L.; Medlin, Douglas L.

    2009-09-01

    Interfaces are a critical determinant of the full range of materials properties, especially at the nanoscale. Computational and experimental methods developed a comprehensive understanding of nanograin evolution based on a fundamental understanding of internal interfaces in nanocrystalline nickel. It has recently been shown that nanocrystals with a bi-modal grain-size distribution possess a unique combination of high-strength, ductility and wear-resistance. We performed a combined experimental and theoretical investigation of the structure and motion of internal interfaces in nanograined metal and the resulting grain evolution. The properties of grain boundaries are computed for an unprecedented range of boundaries. The presence of roughening transitions in grain boundaries is explored and related to dramatic changes in boundary mobility. Experimental observations show that abnormal grain growth in nanograined materials is unlike conventional scale material in both the level of defects and the formation of unfavored phases. Molecular dynamics simulations address the origins of some of these phenomena.

  2. Segregation to grain boundaries in nimonic PE16 superalloy

    International Nuclear Information System (INIS)

    Nettleship, D.J.; Wild, R.K.

    1990-01-01

    Nimonic PE16 alloy is a nickel-based superalloy containing 34 wt.% iron and 16wt.% chromium with additions of molybdenum, titanium and aluminium. It is used in the fuel assembly of the UK advanced gas-cooled reactors (AGR). This component supports significant loads in service and its mechanical integrity is therefore of paramount importance. Mechanical properties may be influenced by the grain size and grain boundary composition, both of which can themselves alter during service. Scanning Auger microscopy is a well-established method for investigating grain boundaries, and has now been applied to the study of PE16. In order to expose PE16 grain boundary surfaces it is necessary to hydrogen charge samples and fracture by pulling in tension at a slow strain rate within the ultra-high vacuum chamber of the Auger microprobe. A series of casts of nimonic PE16 alloy that have received a range of thermal ageing treatments have been fractured in an intergranular manner and the grain boundary composition determined. Segregation of trace and minority elements, particularly Mo and P, has been detected at grain boundaries. Significant variations between different as-manufactured casts were observed, whilst ageing brought about the growth of chromium-rich particles on the grain boundaries. Ductile fracture in PE16 followed a path through Ti(C, N) particles. Many of these particles incorporated large amounts of sulphur. (author)

  3. Grain-boundary migration in Zr-Sn alloys

    International Nuclear Information System (INIS)

    Snowden, K.U.; Stathers, P.A.; Hughes, D.S.

    1979-01-01

    Measurements are reported of grain-boundary migration in a series of Zr-Sn alloys containing from 0.75 to 5.1 wt% Sn (0.58 to 4.0 at% Sn) fatigued under vacuum at temperatures between 600 and 775 0 C. At these temperatures, the condition of the alloys correspond to either the single phase (α) or the double phase (α + Zr 4 Sn) regions of the phase diagram. The amount and rate of grain-boundary migration increased with temperature and decreased with tin addition. The dependence of grain-boundary migration on tin content was a minimum at tin compositions which corresponded to the reported region of the α/(α + Zr 4 Sn) boundary. In the α-region, the reciprocal of the rate of grain-boundary migration was approximately linear with tin content. The temperature dependence for grain-boundary migration exhibited a kinetic transition temperature which divided the dependence into two ranges characterised by different apparent activation energies. The effect of tin additions on both activation energies was to first reduce and then to increase their value. This latter increase is possibly associated with the precipitation of Zr 4 Sn at grain boundaries. (orig.)

  4. Grain boundary and grain interior conduction in γ'-Bi2MoO6

    International Nuclear Information System (INIS)

    Vera, C.M.C.; Aragon, R.

    2005-01-01

    Impedance spectroscopy of fine grained ( 2 MoO 6 samples, in the frequency range of 0.1 Hz-250 kHz, relevant to sensor applications, up to 800 deg. C, has been used to characterize grain boundary and grain interior contributions to conduction. Above 500 deg. C, the grain boundary contribution is no longer rate limiting and conduction is dominated by the grain interior component. The corresponding activation energies are 0.98 eV for grain boundary and 0.73 eV for grain interior components. The weak dependence of conductivity on oxygen partial pressure below 500 deg. C can be attributed to electrode-electrolyte interface phenomena, whereas the robust response to ethanol is commensurate with changes in intrinsic ionic conductivity

  5. Control and Characterization of Individual Grains and Grain Boundaries in Graphene Grown by Chemical Vapour Deposition

    Science.gov (United States)

    2011-06-01

    field (B). Figure 5c presents low temperature (4.3 K) magnetoresistance (Rxx(B)) measurements across the grain boundary compared to Rxx(B) measured within...voltage leads labelled in the legend. c, Four-terminal magnetoresistance (Rxx) measured at 4.3 K within each graphene grain and across the grain boundary...graphene nanoribbons. Nature 444, 347–349 (2006). 37. Huang, M. Y. et al. Phonon softening and crystallographic orientation of strained graphene studied by

  6. Basic aspects of high-Tc grain boundary devices

    International Nuclear Information System (INIS)

    Mannhart, J.; Moler, K.A.; Sigrist, M.

    1996-01-01

    Grain boundaries are extensively used as high-quality Josephson junctions in high-T c superconductors. Their superconducting characteristics can generally be well described by conventional models of strongly coupled Josephson junctions. Here, we report on highly anomalous critical current vs. magnetic field dependencies of grain boundaries in YBa 2 Cu 3 O 7-x . Direct imaging with scanning SQUID microscopy provides evidence of magnetic flux generated by single grain boundaries. Conventional Josephson junction models cannot explain these effects if a superconducting order parameter with a pure s-wave symmetry is assumed. The results have significant implications for our understanding of the properties of grain boundaries in high-T c superconductors and for their applications. (orig.)

  7. Transformation of slip dislocation in ä3 grain boundary

    Czech Academy of Sciences Publication Activity Database

    Gemperlová, Juliana; Jacques, A.; Gemperle, Antonín; Zárubová, Niva

    2002-01-01

    Roč. 10, - (2002), s. 51-57 ISSN 0927-7056 R&D Projects: GA ČR GA202/98/1281; GA ČR GA202/01/0670 Institutional research plan: CEZ:AV0Z1010914 Keywords : in situ TEM * slip dislocations * grain boundary * grain boundary dislocations * plasticity Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.767, year: 2002

  8. Discovering the Role of Grain Boundary Complexions in Materials

    Energy Technology Data Exchange (ETDEWEB)

    Harmer, Martin P. [Lehigh Univ., Bethlehem, PA (United States)

    2015-03-19

    Grain boundaries are inherently an area of disorder in polycrystalline materials which define the transport and various other material properties. The relationship between the interfacial chemistry, structure and the material properties is not well understood. Among the various taxonomies for grain boundaries, Grain Boundary Complexion is a relatively new conceptual scheme that relates the structure and kinetic properties of grain boundaries. In this classification scheme, grain boundaries are considered to be distinct three dimensional (the thickness being considerably smaller as compared to the other two dimensions but nonetheless discernible) equilibrium thermodynamic phases abutted between two crystalline phases. The stability and structure of these interfacial phases are dictated by various thermodynamic variables such as temperature, stress (pressure), interfacial chemistry (chemical potential) and most importantly by the energies of the adjoining crystal surfaces. These phases are only stable within the constraint of the adjoining grains. Although these interfacial phases are not stable in bulk form, they can transform from one complexion to another as a function of various thermodynamic variables analogous to the behavior of bulk phases. Examples of different complexions have been reported in various publications. However, a systematic investigation exploring the existence of grain boundary complexions in material systems other than alumina remains to be done. Although the role of interfacial chemistry on grain boundary complexions in alumina has been addressed, a clear understanding of the underlying thermodynamics governing complexion formation is lacking. Finally, the effects of grain boundary complexions in bulk material properties are widely unknown. Factors above urge a thorough exploration of grain boundary complexions in a range of different materials systems The purpose of the current program is to verify the existence of grain boundary complexion

  9. Computed Structure of Grain Boundaries Compared with TEM Observations

    NARCIS (Netherlands)

    Hosson, J.Th.M. De; Heringa, J.R.; Schapink, F.W.; Evans, J.H.; Veen, A. van

    1984-01-01

    Employing computer simulation techniques several studies of the relaxation of atoms in coincidence type grain boundaries have been performed in recent years. Often it is difficult to obtain a clear representation of the relaxed boundary structure, especially in the case of small atomic

  10. Grain boundary engineering for structure materials of nuclear reactors

    Science.gov (United States)

    Tan, L.; Allen, T. R.; Busby, J. T.

    2013-10-01

    Grain boundary engineering (GBE), primarily implemented by thermomechanical processing, is an effective and economical method of enhancing the properties of polycrystalline materials. Among the factors affecting grain boundary character distribution, literature data showed definitive effect of grain size and texture. GBE is more effective for austenitic stainless steels and Ni-base alloys compared to other structural materials of nuclear reactors, such as refractory metals, ferritic and ferritic-martensitic steels, and Zr alloys. GBE has shown beneficial effects on improving the strength, creep strength, and resistance to stress corrosion cracking and oxidation of austenitic stainless steels and Ni-base alloys.

  11. Grain boundary engineering for structure materials of nuclear reactors

    International Nuclear Information System (INIS)

    Tan, L.; Allen, T.R.; Busby, J.T.

    2013-01-01

    Grain boundary engineering (GBE), primarily implemented by thermomechanical processing, is an effective and economical method of enhancing the properties of polycrystalline materials. Among the factors affecting grain boundary character distribution, literature data showed definitive effect of grain size and texture. GBE is more effective for austenitic stainless steels and Ni-base alloys compared to other structural materials of nuclear reactors, such as refractory metals, ferritic and ferritic–martensitic steels, and Zr alloys. GBE has shown beneficial effects on improving the strength, creep strength, and resistance to stress corrosion cracking and oxidation of austenitic stainless steels and Ni-base alloys

  12. Phase field modeling of grain structure evolution during directional solidification of multi-crystalline silicon sheet

    Science.gov (United States)

    Lin, H. K.; Lan, C. W.

    2017-10-01

    Evolution of grain structures and grain boundaries (GBs), especially the coincident site lattice GBs, during directional solidification of multi-crystalline silicon sheet are simulated by using a phase field model for the first time. Since the coincident site lattice GBs having lower mobility, tend to follow their own crystallographic directions despite thermal gradients, the anisotropic energy and mobility of GBs are considered in the model. Three basic interactions of GBs during solidification are examined and they are consistent with experiments. The twinning process for new grain formation is further added in the simulation by considering twin nucleation. The effect of initial distribution of GB types and grain orientations is also investigated for the twinning frequency and the evolution of grain size and GB types.

  13. Effect of grain boundary misorientation on discontinuous ...

    Indian Academy of Sciences (India)

    Administrator

    Although the texture of the as-cast structure is weak, the hot-rolled sample exhibits a well-developed basal texture consisting of the 〈0001〉 crystal axis parallel to the normal direction of the sample. Figure 2c shows that recrystallization and subsequent grain growth anneal- ing at 725 K for 72 h did not significantly alter the.

  14. Grain boundary engineering to enhance thermal stability of electrodeposited nickel

    DEFF Research Database (Denmark)

    Alimadadi, Hossein

    by miniaturization of the grains down to nano-meter scale. However, this augments the total grain boundary energy stored in the material, hence, making the material less thermally stable. Coherent twin boundaries are of very low energy and mobility compared to all other boundaries in a FCC material. Accordingly...... interest. The evolution of microstructure in as-deposited and annealed condition was investigated with a combination of complementary microscopic techniques, electron backscatter diffraction (EBSD), electron channelling contrast imaging (ECCI), ion channelling contrast imaging (ICCI), and, for the as...

  15. Twinning interactions induced amorphisation in ultrafine silicon grains

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Y. [School of Mechanical and Manufacturing Engineering, University of New South Wales, Sydney, NSW 2052 (Australia); Zhang, L.C., E-mail: liangchi.zhang@unsw.edu.au [School of Mechanical and Manufacturing Engineering, University of New South Wales, Sydney, NSW 2052 (Australia); Zhang, Y. [School of Mechatronics Engineering, Harbin Institute of Technology (China)

    2016-03-21

    Detailed transmission electron microscopy analysis on a severely deformed Al-Si composite material has revealed that partial dislocation slips and deformation twinning are the major plastic deformation carriers in ultrafine silicon grains. This resembles the deformation twinning activities and mechanisms observed in nano-crystalline face-centred-cubic metallic materials. While deformation twinning and amorphisation in Si were thought unlikely to co-exist, it is observed for the first time that excessive twinning and partial dislocation interactions can lead to localised solid state amorphisation inside ultrafine silicon grains.

  16. Nonlinear Dynamics of Vortices in Different Types of Grain Boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Sheikhzada, Ahmad [Old Dominion Univ., Norfolk, VA (United States)

    2017-05-01

    As a major component of linear particle accelerators, superconducting radio-frequency (SRF) resonator cavities are required to operate with lowest energy dissipation and highest accelerating gradient. SRF cavities are made of polycrystalline materials in which grain boundaries can limit maximum RF currents and produce additional power dissipation sources due to local penetration of Josephson vortices. The essential physics of vortex penetration and mechanisms of dissipation of vortices driven by strong RF currents along networks of grain boundaries and their contribution to the residual surface resistance have not been well understood. To evaluate how GBs can limit the performance of SRF materials, particularly Nb and Nb3Sn, we performed extensive numerical simulations of nonlinear dynamics of Josephson vortices in grain boundaries under strong dc and RF fields. The RF power due to penetration of vortices both in weakly-coupled and strongly-coupled grain boundaries was calculated as functions of the RF field and frequency. The result of this calculation manifested a quadratic dependence of power to field amplitude at strong RF currents, an illustration of resistive behavior of grain boundaries. Our calculations also showed that the surface resistance is a complicated function of field controlled by penetration and annihilation of vortices and antivortices in strong RF fields which ultimately saturates to normal resistivity of grain boundary. We found that Cherenkov radiation of rapidly moving vortices in grain boundaries can produce a new instability causing generation of expanding vortex-antivortex pair which ultimately drives the entire GB in a resistive state. This effect is more pronounced in polycrystalline thin film and multilayer coating structures in which it can cause significant increase in power dissipation and results in hysteresis effects in I-V characteristics, particularly at low temperatures.

  17. Grain boundary character dependence of oxygen grain boundary diffusion in α-Al2O3 bicrystals

    International Nuclear Information System (INIS)

    Nakagawa, Tsubasa; Nishimura, Hitoshi; Sakaguchi, Isao; Shibata, Naoya; Matsunaga, Katsuyuki; Yamamoto, Takahisa; Ikuhara, Yuichi

    2011-01-01

    We measured oxygen diffusion coefficients (D gb ) along five grain boundaries (GBs) in alumina bicrystals by tracing 18 O by secondary ion mass spectrometry. Although all boundaries are classified as coincident site lattice boundaries with relatively ordered structures, D gb varied up to 10 3 times among them. On the other hand, the boundaries with identical boundary planes had relatively similar diffusivities as well as similar structures, regardless of Σ values. These results suggest that D gb are related to GB atomic structures and hence the GB character, especially GB planes.

  18. Radiation-induced grain boundary segregation in austenitic stainless steels

    International Nuclear Information System (INIS)

    Bruemmer, S.M.; Charlot, L.A.; Vetrano, J.S.; Simonen, E.P.

    1994-11-01

    Radiation-induced segregation (RIS) to grain boundaries in Fe-Ni-Cr-Si stainless alloys has been measured as a function of irradiation temperature and dose. Heavy-ion irradiation was used to produce damage levels from 1 to 20 displacements per atom (dpa) at temperatures from 175 to 550 degrees C. Measured Fe, Ni, and Cr segregation increased sharply with irradiation dose (from G to 5 dpa) and temperature (from 175 to about 350 degrees C). However, grain boundary concentrations did not change significantly as dose or temperatures were further increased. Although interfacial compositions were similar, the width of radiation-induced enrichment or depletion profiles increased consistently with increasing dose or temperature. Impurity segregation (Si and P) was also measured, but only Si enrichment appeared to be radiation-induced. Grain boundary Si peaked at levels approaching 10 at% after irradiation doses to 10 dpa at an intermediate temperature of 325 degrees C. No evidence of grain boundary silicide precipitation was detected after irradiation at any temperature. Equilibrium segregation of P was measured in the high-P alloys, but interfacial concentration did not increase with irradiation exposure. Comparisons to reported RIS in neutron-irradiated stainless steels revealed similar grain boundary compositional changes for both major alloying and impurity elements

  19. Statistical model for grain boundary and grain volume oxidation kinetics in UO2 spent fuel

    International Nuclear Information System (INIS)

    Stout, R.B.; Shaw, H.F.; Einziger, R.E.

    1989-09-01

    This paper addresses statistical characteristics for the simplest case of grain boundary/grain volume oxidation kinetics of UO 2 to U 3 O 7 for a fragment of a spent fuel pellet. It also presents a limited discussion of future extensions to this simple case to represent the more complex cases of oxidation kinetics in spent fuels. 17 refs., 1 fig

  20. Inter-grain coupling effects on Coulomb oscillations in dual-gated nanocrystalline silicon point-contact transistors

    International Nuclear Information System (INIS)

    Khalafalla, M.A.H.; Durrani, Z.A.K.; Mizuta, H.; Ahmed, H.; Oda, S.

    2005-01-01

    Inter-grain electron-coupling effects are investigated at 4.2 K in dual-gated, point-contact, single-electron transistors fabricated in nanocrystalline silicon. The nanocrystalline silicon film is ∼40 nm thick, with grains ∼10-30 nm in size. The point-contact transistor channel is ∼30 nmx30 nmx40 nm in size, with two side-gates. Only a few grains exist within the channel and different grains contribute in varying degrees to the device conduction. By modifying the inter-grain coupling using selective oxidation of the grain boundaries, both electrostatic and wavefunction-coupling effects can be observed in the Coulomb oscillations vs. the two gate voltages

  1. Present state of the controversy about the grain boundary relaxation

    International Nuclear Information System (INIS)

    Povolo, F.; Molinas, B.J.

    1990-04-01

    An analysis of the internal friction produced by grain boundary relaxation in metals, alloys and ceramics is presented. The different interpretations given in the literature to relaxation phenomena occurring at temperatures above about half the melting point which include the influence of grain boundaries and their interaction with solutes and precipitates are discussed in detail. A complete set of the experimental data disposable in this field since 1972 until today is reviewed. Finally, some recent experiments are discussed and new ones are suggested. They might solve the actual controversy about the real origin of the relaxation phenomena observed. If this is the case, a considerable amount of information already published can be taken into account with a good degree of confidence. This information contributes to the description of the structure and behaviour of grain boundaries, both being important topics for materials science. (author). 119 refs, 21 figs, 1 tab

  2. Grain Boundary Assemblies in Dynamically-Recrystallized Austenitic Stainless Steel

    Directory of Open Access Journals (Sweden)

    Marina Tikhonova

    2016-11-01

    Full Text Available The grain boundary misorientation distributions associated with the development of dynamic recrystallization were studied in a high-nitrogen austenitic stainless steel subjected to hot working. Under conditions of discontinuous dynamic recrystallization, the relationships between the grain or subgrain sizes and flow stresses can be expressed by power law functions with different grain/subgrain size exponents of about −0.76 (for grain size or −1.0 (for subgrain size. Therefore, the mean grain size being much larger than the subgrain size under conditions of low flow stress gradually approaches the size of the subgrains with an increase in the flow stress. These dependencies lead to the fraction of high-angle boundaries being a function of the flow stress. Namely, the fraction of ordinary high-angle boundaries in dynamically-recrystallized structures decreases with a decrease in the flow stress. On the other hand, the fraction of special boundaries, which are associated with annealing twins, progressively increases with a decrease of the flow stress.

  3. Grain-boundary melting: A Monte Carlo study

    DEFF Research Database (Denmark)

    Besold, Gerhard; Mouritsen, Ole G.

    1994-01-01

    Grain-boundary melting in a lattice-gas model of a bicrystal is studied by Monte Carlo simulation using the grand canonical ensemble. Well below the bulk melting temperature T(m), a disordered liquidlike layer gradually emerges at the grain boundary. Complete interfacial wetting can be observed...... when the temperature approaches T(m) from below. Monte Carlo data over an extended temperature range indicate a logarithmic divergence w(T) approximately - ln(T(m)-T) of the width of the disordered layer w, in agreement with mean-field theory....

  4. Dislocation Nucleation on Grain Boundaries: Low Angle Twist and Asymmetric Tilt Boundaries

    Directory of Open Access Journals (Sweden)

    Erman Guleryuz

    2016-07-01

    Full Text Available We investigate the mechanisms of incipient plasticity at low angle twist and asymmetric tilt boundaries in fcc metals. To observe plasticity of grain boundaries independently of the bulk plasticity, we simulate nanoindentation of bicrystals. On the low angle twist boundaries, the intrinsic grain boundary (GB dislocation network deforms under load until a dislocation segment compatible with glide on a lattice slip plane is created. The half loops are then emitted into the bulk of the crystal. Asymmetric twist boundaries considered here did not produce bulk dislocations under load. Instead, the boundary with a low excess volume nucleated a mobile GB dislocation and additional GB defects. The GB sliding proceeded by motion of the mobile GB dislocation. The boundary with a high excess volume sheared elastically, while bulk-nucleated dislocations produced plastic relaxation.

  5. The effect of grain refinement and silicon content on grain formation in hypoeutectic Al-Si alloys

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Y.C.; Dahle, A.K.; StJohn, D.H.; Hutt, J.E.C. [Queensland Univ., Brisbane (Australia). Dept. of Mining, Minerals and Mater. Eng.

    1999-01-15

    The effect of increasing the amount of added grain refiner on grain size and morphology has been investigated for a range of hypoeutectic Al-Si alloys. The results show a transition in grain size at a silicon concentration of about 3 wt% in unrefined alloys; the grain size decreasing with silicon content before the transition, and increasing beyond the transition point. A change in morphology also occurs with increased silicon content. The addition of grain refiner leads to greater refinement for silicon contents below the transition point than for those contents above the transition point, while the transition point seems to remain unchanged. The slope of the grain size versus silicon content curve after the transition seems to be unaffected by the degree of grain refinement. The results are related to the competitive processes of nucleation and constitutional effects during growth and their impact on nucleation kinetics. (orig.) 13 refs.

  6. Grain boundary effects on the mechanical properties of bismuth nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Burek, Michael J.; Jin, Sumin; Leung, Michael C.; Jahed, Zeinab; Wu, Janet [Waterloo Institute for Nanotechnology, University of Waterloo, 200 University Avenue West, Waterloo, ON, N2L 3G1 (Canada); Budiman, Arief Suriadi [Center for Integrated Nanotechnologies, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Tamura, Nobumichi; Kunz, Martin [Advanced Light Source, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Tsui, Ting Y., E-mail: tttsui@uwaterloo.ca [Waterloo Institute for Nanotechnology, University of Waterloo, 200 University Avenue West, Waterloo, ON, N2L 3G1 (Canada)

    2011-06-15

    Cylindrical bismuth nanopillars with diameters between 130 and 1100 nm were fabricated by electron beam lithography and electroplating. The microstructure of the electrodeposited bismuth was established to be polycrystalline with a wide distribution of grains from {approx}0.1 to 1 {mu}m in size. A clear transition in the mechanism governing the plastic deformation of bismuth nanopillars is observed as the nanopillar size becomes comparable with the average grain size of 280 nm. In larger nanopillar specimens, where the average grain size is much smaller than the nanopillar diameter, deformation is dominated by grain boundary-mediated mechanisms. When the bismuth nanopillar diameter approaches the average grain size the deformation behavior transitions to a mechanism dominated by dislocation dynamics. This transition is identified by post-compression scanning electron microscopy, strain rate sensitivity, and average flow stresses.

  7. Grain boundary dynamics in ceramics superplasticity

    Directory of Open Access Journals (Sweden)

    Wakai, E.

    2001-04-01

    Full Text Available Superplasticity refers to an ability of polycrystalline solids to exhibit exceptionally large elongation in tension. The application of superplasticity makes it possible to fabricate ceramic components by superplastic forming (SPF, concurrent with diffusion bonding, and superplastic sinter-forging just like superplastic metals. Furthermore the superplastic deformation plays an important role in stress-assisted densification processes such as hot isostatic pressing (HIP and hot pressing (HP. The ceramics superplasticity has been one of intensive research fields in the last decade. Although most of reports are still limited to those of zirconia[1], new developments have been achieved in superplasticity of Si3N4 and SiC in recent years. It is clearly demonstrated that the superplasticity is one of the common natures of fine-grained ceramics and nanocrystalline ceramics at elevated temperatures.

    La superplaticidad se refiere a la capacidad que posee un sólido policristalino de presentar alargamientos excepcionalmente elevados en tracción. La aplicación de la superplasticidad hace posible la fabricación de componentes cerámicos por conformado superplástico, soldadura por difusión y forja-sinterizado superplástica, igual que en metales superplásticos. Además, la deformación superplástica tiene un rol importante en los procesos de densificación asistidos por tensiones, tales como la compactación isostática en caliente y el prensado en caliente. Las cerámicas superplásticas han sido uno de los campos donde se ha realizado una investigación más intensa en la última década. Aunque, la mayoría de los informes se limitan a la circonia[1] se han alcanzado nuevos desarrollos en superplasticidad de Si3N4 y SiC. Está claramente demostrado que la superplasticidad es una propiedad intrínseca de las cerámicas de pequeño tamaño de grano y de las cer

  8. Single Grain Boundary Modeling and Design of Microcrystalline Si Solar Cells

    Directory of Open Access Journals (Sweden)

    Chu-Hsuan Lin

    2013-01-01

    Full Text Available For photovoltaic applications, microcrystalline silicon has a lot of advantages, such as the ability to absorb the near-infrared part of the solar spectrum. However, there are many dangling bonds at the grain boundary in microcrystalline Si. These dangling bonds would lead to the recombination of photo-generated carriers and decrease the conversion efficiency. Therefore, we included the grain boundary in the numerical study in order to simulate a microcrystalline Si solar cell accurately, designing new three-terminal microcrystalline Si solar cells. The 3-μm-thick three-terminal cell achieved a conversion efficiency of 10.8%, while the efficiency of a typical two-terminal cell is 9.7%. The three-terminal structure increased the JSC but decreased the VOC, and such phenomena are discussed. High-efficiency and low-cost Si-based thin film solar cells can now be designed based on the information provided in this paper.

  9. Single Grain Boundary Modeling and Design of Microcrystalline Si Solar Cells.

    Science.gov (United States)

    Lin, Chu-Hsuan; Hsu, Wen-Tzu; Tai, Cheng-Hung

    2013-01-21

    For photovoltaic applications, microcrystalline silicon has a lot of advantages, such as the ability to absorb the near-infrared part of the solar spectrum. However, there are many dangling bonds at the grain boundary in microcrystalline Si. These dangling bonds would lead to the recombination of photo-generated carriers and decrease the conversion efficiency. Therefore, we included the grain boundary in the numerical study in order to simulate a microcrystalline Si solar cell accurately, designing new three-terminal microcrystalline Si solar cells. The 3-μm-thick three-terminal cell achieved a conversion efficiency of 10.8%, while the efficiency of a typical two-terminal cell is 9.7%. The three-terminal structure increased the J SC but decreased the V OC , and such phenomena are discussed. High-efficiency and low-cost Si-based thin film solar cells can now be designed based on the information provided in this paper.

  10. Direct characterization of boron segregation at random and twin grain boundaries*

    International Nuclear Information System (INIS)

    Li Xiang-Long; Wu Ping; Yang Rui-Jie; Zhang Shi-Ping; Chen Sen; Wang Xue-Min; Huai Xiu-Lan

    2017-01-01

    Boron distribution at grain boundaries in hot-deformed nickel is directly characterized by the time-of-flight secondary ion mass spectrometry. The segregations of boron are observed at both the random and twin grain boundaries. Two types of segregations at random grain boundaries are observed. The first type of segregation has a high intensity and small width. Its formation is attributed to the incorporating of dislocations into the moving grain boundaries. The second type of segregation arises from the cooling induced segregation at the dislocations associated with the grain boundaries. The segregation at twin boundary is similar to the second type of segregation at random grain boundaries. (paper)

  11. Grain boundary diffusion in terms of the tempered fractional calculus

    International Nuclear Information System (INIS)

    Sibatov, R.T.; Svetukhin, V.V.

    2017-01-01

    Mathematical treatment of grain-boundary diffusion based on the model first proposed by Fisher is usually formulated in terms of normal diffusion equations in a two-component nonhomogeneous medium. On the other hand, fractional equations of anomalous diffusion proved themselves to be useful in description of grain-boundary diffusion phenomena. Moreover, the most important propagation regime predicted by Fisher's model demonstrates subdiffusive behavior. However, the direct link between fractional approach and the Fisher model and its modifications has not found yet. Here, we fill this gap and show that solution of fractional subdiffusion equation offers general properties of classical solutions obtained by Whipple and Suzuoka. The tempered fractional approach is a convenient tool for studying precipitation in granular materials as the tempered subdiffusion limited process. - Highlights: • The link connected fractional diffusion approach and Fisher's model of grain-boundary diffusion is derived. • The subdiffusion exponent of grain-boundary diffusion can differ from 1/2. • Nucleation in granular materials is modeled by the process limited by tempered subdiffusion.

  12. A grain boundary sliding model for cavitation, crack growth and ...

    African Journals Online (AJOL)

    A model is presented for cavity growth, crack propagation and fracture resulting from grain boundary sliding (GBS) during high temperature creep deformation. The theory of cavity growth by GBS was based on energy balance criteria on the assumption that the matrix is sufficiently plastic to accommodate misfit strains ...

  13. Grain-boundary cavitation and migration during high temperature fatigue

    International Nuclear Information System (INIS)

    Snowden, K.U.; Stathers, P.A.; Hughes, D.S.

    1980-01-01

    Studies have been made of the grain-boundary phenomena (cavitation, grain-boundary migration, fractional density change) that occurred during high temperature fatigue tests on commercial purity copper and crystal bar zirconium. The tests were performed on sheet specimens in reverse plane bending at 16 Hz at constant strain amplitudes and under vacuum. The temperature ranges were 360 to 550 0 C for copper and 600 to 775 0 C for zirconium. The numbers of cavities per unit area were estimated at various stages of the fatigue life for copper and zirconium tested at a strain amplitude of +- 0.21%. Most cavities were nucleated during the first 10 to 20% of the fatigue life, when an orthogonal or 'square' grain structure was formed by grain-boundary migration. The rate of migration was highest during this period and the average migration distance was proportional to Nsup(α), where N is the number of strain cycles and α = 2/3. The fractional density change was proportional to N throughout the fatigue life. For zirconium, the temperature dependence of the rates of boundary migration and fractional density change exhibited two distinct regions, which were characterised by differences in apparent activation energy. However, in the case of copper, there was no evidence for a transition temperature. The variations of the fractional density change with N and with temperature were compared with those predicted by theories of high temperature fatigue. (author)

  14. Enthalpy - entropy compensation effect in grain boundary phenomena

    Czech Academy of Sciences Publication Activity Database

    Lejček, Pavel

    2005-01-01

    Roč. 96, č. 10 (2005), s. 1129-1133 ISSN 0044-3093 R&D Projects: GA MPO(CZ) FF-P2/053 Institutional research plan: CEZ:AV0Z10100520 Keywords : compensation effect * enthalpy * entropy * thermodynamics * grain boundary Subject RIV: BJ - Thermodynamics Impact factor: 0.842, year: 2005

  15. Kinetics of interstitial segregation in Cottrell atmospheres and grain boundaries

    Czech Academy of Sciences Publication Activity Database

    Svoboda, Jiří; Zickler, G. A.; Kozeschnik, E.; Fischer, F. D.

    2015-01-01

    Roč. 95, č. 9 (2015), s. 458-465 ISSN 0950-0839 R&D Projects: GA ČR(CZ) GA15-06390S Institutional support: RVO:68081723 Keywords : segregation * grain boundaries * dislocations * simulation * thermodynamic extremal principle Subject RIV: BJ - Thermodynamics Impact factor: 0.918, year: 2015

  16. Studies of Grain Boundaries in Materials Subjected to Diffusional Creep

    DEFF Research Database (Denmark)

    Nørbygaard, Thomas

    Grain boundaries in crystalline Cu(2%Ni) creep specimens have been studied by use of scanning and transmission electron microscopy in order to establish the mechanism of deformation. Creep rate measurements and dependencies were found to fit reasonably well with the model for diffusional creep...

  17. Modelling of recrystallization and grain boundary migration by cellular automata

    Czech Academy of Sciences Publication Activity Database

    Kroc, J.; Paidar, Václav

    426-432, - (2003), s. 3873-3878 ISSN 0255-5476 R&D Projects: GA ČR GA202/02/0916 Institutional research plan: CEZ:AV0Z1010914 Keywords : cellular automata * dynamic recrystallization * grain boundary migration * modeling * simulation Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.602, year: 2003

  18. Slip transfer across grain boundaries in Fe-Si bicrystals

    Czech Academy of Sciences Publication Activity Database

    Gemperlová, Juliana; Polcarová, Milena; Gemperle, Antonín; Zárubová, Niva

    2004-01-01

    Roč. 378, - (2004), s. 97-101 ISSN 0925-8388 R&D Projects: GA ČR GA202/01/0670 Institutional research plan: CEZ:AV0Z1010914 Keywords : metals * dislocations and disclinations * bicrystals * grain boundaries * transmission electron microscopy * X-ray diffraction Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.562, year: 2004

  19. Grain boundary diffusion in terms of the tempered fractional calculus

    Energy Technology Data Exchange (ETDEWEB)

    Sibatov, R.T., E-mail: ren_sib@bk.ru [Ulyanovsk State University, 432017, 42 Leo Tolstoy str., Ulyanovsk (Russian Federation); Svetukhin, V.V. [Ulyanovsk State University, 432017, 42 Leo Tolstoy str., Ulyanovsk (Russian Federation); Institute of Nanotechnology and Microelectronics of the Russian Academy of Sciences, 115487, 18 Nagatinskaya str., Moscow (Russian Federation)

    2017-06-28

    Mathematical treatment of grain-boundary diffusion based on the model first proposed by Fisher is usually formulated in terms of normal diffusion equations in a two-component nonhomogeneous medium. On the other hand, fractional equations of anomalous diffusion proved themselves to be useful in description of grain-boundary diffusion phenomena. Moreover, the most important propagation regime predicted by Fisher's model demonstrates subdiffusive behavior. However, the direct link between fractional approach and the Fisher model and its modifications has not found yet. Here, we fill this gap and show that solution of fractional subdiffusion equation offers general properties of classical solutions obtained by Whipple and Suzuoka. The tempered fractional approach is a convenient tool for studying precipitation in granular materials as the tempered subdiffusion limited process. - Highlights: • The link connected fractional diffusion approach and Fisher's model of grain-boundary diffusion is derived. • The subdiffusion exponent of grain-boundary diffusion can differ from 1/2. • Nucleation in granular materials is modeled by the process limited by tempered subdiffusion.

  20. Measurement of spatial stress gradients near grain boundaries

    NARCIS (Netherlands)

    Basu, Indranil; Ocelík, Vaclav; De Hosson, Jeff Th M.

    2017-01-01

    A correlative method based on electron back scattered diffraction and focused ion-beam-digital image correlation slit milling technique was used to quantitatively determine spatially resolved stress profiles in the vicinity of grain boundaries in pure titanium. Measured local stress gradients were

  1. Positron annihilation in vacancies at grain boundaries in metals

    Czech Academy of Sciences Publication Activity Database

    Kuriplach, J.; Melikhova, O.; Hou, M.; Van Petegem, S.; Zhurkin, E.; Šob, Mojmír

    2008-01-01

    Roč. 255, č. 1 (2008), s. 128-132 ISSN 0169-4332 R&D Projects: GA MŠk OC 147; GA AV ČR IAA1041302 Institutional research plan: CEZ:AV0Z20410507 Keywords : Positron annihilation * Grain boundaries * Vacancies Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.576, year: 2008

  2. Subgroup report on grain boundary and interphase boundary structure and properties

    International Nuclear Information System (INIS)

    Balluffi, R.W.; Cannon, R.M.; Clarke, D.R.; Heuer, A.H.; Ho, P.S.; Kear, B.H.; Vitek, V.; Weertman, J.R.; White, C.L.

    1979-01-01

    In many high temperature structural applications, the performance characteristics of a materials system are largely controlled by the properties of its grain and interphase boundaries. Failure in creep and fatigue frequently occurs by cavitation, or cracking along grain boundaries. In a few special cases, this failure problem has been overcome by directional alignment of grain and interphase boundaries by various types of metallurgical processing such as directional solidification and directional recrystallization. A good example is to be found in the application of directionally aligned structures in high performance gas-turbine airfoils. However, where fine, equiaxed grain structures are desirable, other methods of controlling grain boundary properties have been developed. Important among these has been the introduction of improvements in primary melting practices, designed to control important impurities. This is of decisive importance because even traces of certain impurity elements present in grain boundaries in high temperature materials can seriously affect properties. Impurities are deleterious and need to be removed. However, in certain cases, (e.g., creep fracture) controlled impurity additions can be beneficial and result in improved properties

  3. Grain-boundary unzipping by oxidation in polycrystalline graphene

    Science.gov (United States)

    Alexandre, Simone; Lucio, Aline; Nunes, Ricardo

    2011-03-01

    The need for large-scale production of graphene will inevitably lead to synthesis of the polycrystalline material [1,2]. Understanding the chemical, mechanical, and electronic properties of grain boundaries in graphene polycrystals will be crucial for the development of graphene-based electronics. Oxidation of this material has been suggested to lead to graphene ribbons, by the oxygen-driven unzipping mechanism. A cooperative-strain mechanism, based on the formation of epoxy groups along lines of parallel bonds in the hexagons of graphene's honeycomb lattice, was proposed to explain the unzipping effect in bulk graphene In this work we employ ab initio calculations to study the oxidation of polycrystalline graphene by chemisorption of oxygen at the grain boundaries. Our results indicate that oxygen tends to segregate at the boundaries, and that the unzipping mechanism is also operative along the grain boundaries, despite the lack of the parallel bonds due to the presence of fivefold and sevenfold carbon rings along the boundary core. We acknowledge support from the Brazilian agencies: CNPq, Fapemig, and INCT-Materiais de Carbono.

  4. Grain boundary engineering to enhance thermal stability of electrodeposited nickel

    DEFF Research Database (Denmark)

    Alimadadi, Hossein

    Manufacturing technologies such as injection molding and micro electromechanical systems demand materials with improved mechanical properties (e.g. hardness, ductility) and high durability at elevated temperatures. Significant improvement in some of the mechanical properties is obtained by miniat......Manufacturing technologies such as injection molding and micro electromechanical systems demand materials with improved mechanical properties (e.g. hardness, ductility) and high durability at elevated temperatures. Significant improvement in some of the mechanical properties is obtained...... by miniaturization of the grains down to nano-meter scale. However, this augments the total grain boundary energy stored in the material, hence, making the material less thermally stable. Coherent twin boundaries are of very low energy and mobility compared to all other boundaries in a FCC material. Accordingly......, grain boundary engineering of electrodeposited nickel to achieve high population of coherent twin boundaries and, hence, higher thermal stability is a promising method to achieve simultaneous improvement in mechanical properties and thermal stability. This is of particular scientific and practical...

  5. Grain-size distributions and grain boundaries of chalcopyrite-type thin films

    International Nuclear Information System (INIS)

    Abou-Ras, D.; Schorr, S.; Schock, H.W.

    2007-01-01

    CuInSe 2 , CuGaSe 2 , Cu(In,Ga)Se 2 and CuInS 2 thin-film solar absorbers in completed solar cells were studied in cross section by means of electronbackscatter diffraction. From the data acquired, grain-size distributions were extracted, and also the most frequent grain boundaries were determined. The grain-size distributions of all chalcopyrite-type thin films studied can be described well by lognormal distribution functions. The most frequent grainboundary types in these thin films are 60 - left angle 221 right angle tet and 71 - left angle 110 right angle tet (near) Σ3 twin boundaries. These results can be related directly to the importance of {112} tet planes during the topotactical growth of chalcopyrite-type thin films. Based on energetic considerations, it is assumed that the most frequent twin boundaries exhibit a 180 - left angle 221 right angle tet constellation. (orig.)

  6. Co boundary diffusion in zircon-α grains

    International Nuclear Information System (INIS)

    Corvalan, C; Iribarren, M; Dyment, F

    2006-01-01

    Diffusion in solid state plays a decisive part in most metallurgical processes and, therefore, determining the values of the diffusion coefficients becomes very important. Diffusion in materials in general and in metals in particular occurs because of defects. These can be classified as specific, lineal, bi- and tri-dimensional, and coefficients may be determined for diffusion volume, grain and interphase boundary diffusion, diffusion dislocation, and surface diffusion. A grain boundary (GB) is defined as the region of transition between two adjacent crystals in a single-phase material, which are in contact and only differ in crystallographic orientation. When the transition zone between two grains occurs between two phases of an alloy, it is called interphase boundary (IB). The GB as well as the IB show migration speeds several orders of magnitude greater than those for the volumes of the adjacent regions. At temperatures where the diffusion volume can be considered practically nil, an appreciable although localized amount of material can be displaced along the 'fast-paths'. This implies that not only the diffusion itself, but also the associated phenomena on the grain and interphase boundaries are accelerating. Among these phenomena are: plastic deformation and corrosion at high temperature, stability of precipitates in a synthesized matrix, surface treatments, solid state transformations in general, etc. The experimental determination of the coefficients of diffusion in grain boundaries (GB) and interphase boundaries (IB) yields information about the speeds of migration in the intergranular regions, where important and localized phenomena occur. The B and C kinetics from the Harrison classification are used in this study, which provide reliable results although with some restrictions. This study presents the results of Co diffusion in the GB of pure Zr-α, in the temperature range [430-633] K, with those for C kinetics being the first in this type of material

  7. Large modulation of carrier transport by grain-boundary molecular packing and microstructure in organic thin films

    KAUST Repository

    Rivnay, Jonathan

    2009-11-08

    Solution-processable organic semiconductors are central to developing viable printed electronics, and performance comparable to that of amorphous silicon has been reported for films grown from soluble semiconductors. However, the seemingly desirable formation of large crystalline domains introduces grain boundaries, resulting in substantial device-to-device performance variations. Indeed, for films where the grain-boundary structure is random, a few unfavourable grain boundaries may dominate device performance. Here we isolate the effects of molecular-level structure at grain boundaries by engineering the microstructure of the high-performance n-type perylenediimide semiconductor PDI8-CN 2 and analyse their consequences for charge transport. A combination of advanced X-ray scattering, first-principles computation and transistor characterization applied to PDI8-CN 2 films reveals that grain-boundary orientation modulates carrier mobility by approximately two orders of magnitude. For PDI8-CN 2 we show that the molecular packing motif (that is, herringbone versus slip-stacked) plays a decisive part in grain-boundary-induced transport anisotropy. The results of this study provide important guidelines for designing device-optimized molecular semiconductors. © 2009 Macmillan Publishers Limited. All rights reserved.

  8. Microscale Liquid Transport in Polycrystalline Inverse Opals across Grain Boundaries.

    Science.gov (United States)

    Pham, Q N; Barako, M T; Tice, J; Won, Y

    2017-09-05

    Delivering liquid through the void spaces in porous metals is a daunting challenge for a variety of emerging interface technologies ranging from battery electrodes to evaporation surfaces. Hydraulic transport characteristics of well-ordered porous media are governed by the pore distribution, porosity, and morphology. Much like energy transport in polycrystalline solids, hydraulic transport in semi-ordered porous media is predominantly limited by defects and grain boundaries. Here, we report the wicking performances for porous copper inverse opals having pore diameters from 300 to 1000 nm by measuring the capillary-driven liquid rise. The capillary performance parameter within single crystal domain (K ij /R eff  = 10 -3 to 10 -2  µm) is an order of magnitude greater than the collective polycrystal (K eff /R eff  = ~10 -5 to 10 -3  µm) due to the hydraulic resistances (i.e. grain boundaries between individual grains). Inspired by the heterogeneity found in biological systems, we report that the capillary performance parameter of gradient porous copper (K eff /R eff  = ~10 -3  µm), comparable to that of single crystals, overcomes hydraulic resistances through providing additional hydraulic routes in three dimensions. The understanding of microscopic liquid transport physics through porous crystals and across grain boundaries will help to pave the way for the spatial design of next-generation heterogeneous porous media.

  9. Long time scale simulation of a grain boundary in copper

    DEFF Research Database (Denmark)

    Pedersen, A.; Henkelman, G.; Schiøtz, Jakob

    2009-01-01

    A general, twisted and tilted, grain boundary in copper has been simulated using the adaptive kinetic Monte Carlo method to study the atomistic structure of the non-crystalline region and the mechanism of annealing events that occur at low temperature. The simulated time interval spanned 67 mu s...... was also observed. In the final low-energy configurations, the thickness of the region separating the crystalline grains corresponds to just one atomic layer, in good agreement with reported experimental observations. The simulated system consists of 1307 atoms and atomic interactions were described using...

  10. Grain boundary embrittlement and cohesion enhancement in copper

    Energy Technology Data Exchange (ETDEWEB)

    Paxton, Anthony; Lozovoi, Alexander [Atomistic Simulation Centre, Queen' s University Belfast, BT7 1NN (United Kingdom); Schweinfest, Rainer [Science+Computing ag, Hagellocher Weg 71-5, 720270 T ubingen (Germany); Finnis, Michael [Imperial College London, Exhibition Road, London SW7 2AZ (United Kingdom)

    2008-07-01

    There has been a long standing debate surrounding the mechanism of grain boundary embrittlement and cohesion enhancement in metals. Embrittlement can lead to catastrophic failure such as happened in the Hinkley Point disaster, or indeed in the case of the Titanic. This kind of embrittlement is caused by segregation of low solubility impurities to grain boundaries. While the accepted wisdom is that this is a phenomenon driven by electronic or chemical factors, using language such as charge transfer and electronegativity difference; we believe that in copper, at least, both cohesion enhancement and reduction are caused by a simple size effect. We have developed a theory that allows us to separate unambiguously, if not uniquely, chemical and structural factors. We have studied a large number of solutes in copper using first principles atomistic simulation to support this argument, and the results of these calculations are presented here.

  11. Multilevel model of polycrystalline materials: grain boundary sliding description

    Science.gov (United States)

    Sharifullina, E.; Shveykin, A.; Trusov, P.

    2017-12-01

    Material behavior description in a wide range of thermomechanical effects is one of the topical areas in mathematical modeling. Inclusion of grain boundary sliding as an important mechanism of polycrystalline material deformation at elevated temperatures and predominant deformation mechanism of metals and alloys in structural superplasticity allows to simulate various deformation regimes and their transitions (including superplasticity regime with switch-on and switch-off regimes). The paper is devoted to description of grain boundary sliding in structure of two-level model, based on crystal plasticity, and relations for determination the contribution of this mechanism to inelastic deformation. Some results are presented concerning computational experiments of polycrystalline representative volume deformation using developed model.

  12. Influence of Grain Boundary Character and Annealing Time on Segregation in Commercially Pure Nickel

    Directory of Open Access Journals (Sweden)

    Shery L. Welsh

    2016-01-01

    Full Text Available Commercially pure nickel (Ni was thermomechanically processed to promote an increase in Σ3 special grain boundaries. Engineering the character and chemistry of Σ3 grain boundaries in polycrystalline materials can help in improving physical, chemical, and mechanical properties leading to improved performance. Type-specific grain boundaries (special and random were characterized using electron backscatter diffraction and the segregation behavior of elements such as Si, Al, C, O, P, Cr, Mg, Mn, B, and Fe, at the atomic level, was studied as a function of grain boundary character using atom probe tomography. These results showed that the random grain boundaries were enriched with impurities to include metal oxides, while Σ3 special grain boundaries showed little to no impurities at the grain boundaries. In addition, the influence of annealing time on the concentration of segregants on random grain boundaries was analyzed and showed clear evidence of increased concentration of segregants as annealing time was increased.

  13. Grain boundary diffusion and segregation of Cr in α-Zr

    International Nuclear Information System (INIS)

    Corvalan Moya, C.; Iribarren, M.J.; Di Lalla, N.; Dyment, F.

    2008-01-01

    51 Cr diffusion along grain boundaries in polycrystalline α-Zr was measured by means of the radiotracer technique in the temperature range 449-680 K. The use of Harrison's C and B kinetics provided direct data about grain boundary diffusivity (D gb ) and the apparent grain boundary diffusivity (P gb ) in the temperature range of power reactors service. The grain boundaries segregation factor s of Cr in α-Zr was determined at the limit of very dilute solute concentration

  14. Cadmium Telluride and Grain Boundaries: A Preliminary Study

    Science.gov (United States)

    Liao, Michael Evan

    The efficacy of the CdCl2 treatment on polycrystalline CdTe-based solar cells was discovered over a quarter of a century ago; and yet, the exact mechanism of this treatment is still not fully understood to this day. In fact, the lack of understanding stems from a debate on the exact role of grain boundaries in CdCl2-treated CdTe solar cells. Some hypothesize that the CdCl2-treatment causes grain boundaries to become beneficial to solar cell performance while others disagree and claim that the treatment simply mitigates the harmful effects of grain boundaries via passivation. A future goal of this project is to determine which, if either, hypothesis is correct by direct wafer bonding single crystalline CdTe. Direct wafer bonding of single crystalline materials would create only one grain boundary at the bonded interface. This approach allows the orientation and surface chemistry of interfaces to be controlled in order to study the chemistry of grain boundaries methodically. However, before any direct wafer bonding can be done, a preliminary study of single crystalline CdTe is necessary. High-quality direct wafer bonding can only be achieved if the surfaces of each wafer satisfy certain requirements. Additionally, analyzing single crystalline CdTe materials prior to bonding is crucial in order to make any insightful connections between results found from direct bonding of single crystalline CdTe and what is observed in polycrystalline CdTe. First, the surface of an (001) CdTe layer epitaxially grown on an (001) InSb substrate is studied using atomic force microscopy. Stacking faults on the CdTe surface are observed and the thickness of the grown CdTe epilayer is calculated by considering the interplanar angles between the (001) and (111) crystallographic planes as well as the dimensions of the stacking faults. While the stacking faults will inhibit successful wafer bonding, the roughness of the regions outside the stacking faults is 0.9 nm, which is an acceptable

  15. Density functional theory metadynamics of silver, caesium and palladium diffusion at β-SiC grain boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Rabone, Jeremy, E-mail: jeremy.rabone@ec.europa.eu [European Commission, Joint Research Centre, Institute for Transuranium Elements, D-76125 Karlsruhe (Germany); López-Honorato, Eddie [Centro de Investigación y de Estudios Avanzados del IPN (CINVESTAV), Unidad Saltillo, Industria Metalúrgica 1062, Parque Industrial, Ramos Arizpe 25900, Coahuila (Mexico)

    2015-03-15

    Highlights: • DFT metadynamics of diffusion of Pd, Ag and Cs on grain boundaries in β-SiC. • The calculated diffusion rates for Pd and Ag tally with experimental release rates. • A mechanism of release other than grain boundary diffusion seems likely for Cs. - Abstract: The use of silicon carbide in coated nuclear fuel particles relies on this materials impermeability towards fission products under normal operating conditions. Determining the underlying factors that control the rate at which radionuclides such as Silver-110m and Caesium-137 can cross the silicon carbide barrier layers, and at which fission products such as palladium could compromise or otherwise alter the nature of this layer, are of paramount importance for the safety of this fuel. To this end, DFT-based metadynamics simulations are applied to the atomic diffusion of silver, caesium and palladium along a Σ5 grain boundary and to palladium along a carbon-rich Σ3 grain boundary in cubic silicon carbide at 1500 K. For silver, the calculated diffusion coefficients lie in a similar range (7.04 × 10{sup −19}–3.69 × 10{sup −17} m{sup 2} s{sup −1}) as determined experimentally. For caesium, the calculated diffusion rates are very much slower (3.91 × 10{sup −23}–2.15 × 10{sup −21} m{sup 2} s{sup −1}) than found experimentally, suggesting a different mechanism to the simulation. Conversely, the calculated atomic diffusion of palladium is very much faster (7.96 × 10{sup −11}–7.26 × 10{sup −9} m{sup 2} s{sup −1}) than the observed penetration rate of palladium nodules. This points to the slow dissolution and rapid regrowth of palladium nodules as a possible ingress mechanism in addition to the previously suggested migration of entire nodules along grain boundaries. The diffusion rate of palladium along the Σ3 grain boundary was calculated to be slightly slower (2.38 × 10{sup −11}–8.24 × 10{sup −10} m{sup 2} s{sup −1}) than along the Σ5 grain boundary. Rather

  16. On Techniques to Characterize and Correlate Grain Size, Grain Boundary Orientation and the Strength of the SiC Layer of TRISO Coated Particles: A Preliminary Study

    Energy Technology Data Exchange (ETDEWEB)

    I.J.van Rooyen; J.L. Dunzik Gougar; T. Trowbridge; Philip M van Rooyen

    2012-10-01

    The mechanical properties of the silicon carbide (SiC) layer of the TRi-ISOtropic (TRISO) coated particle (CP) for high temperature gas reactors (HTGR) are performance parameters that have not yet been standardized by the international HTR community. Presented in this paper are the results of characterizing coated particles to reveal the effect of annealing temperature (1000 to 2100°C) on the strength and grain size of unirradiated coated particles. This work was further expanded to include possible relationships between the grain size and strength values. The comparative results of two strength measurement techniques and grain size measured by the Lineal intercept method are included. Preliminary grain boundary characterization results determined by electron backscatter diffraction (EBSD) are included. These results are also important for future fission product transport studies, as grain boundary diffusion is identified as a possible mechanism by which 110mAg, one of the fission activation products, might be released through intact SiC layers. Temperature is a parameter known to influence the grain size of SiC and therefore it is important to investigate the effect of high temperature annealing on the SiC grain size. Recommendations and future work will also be briefly discussed.

  17. Bandgap tunability at single-layer molybdenum disulphide grain boundaries

    KAUST Repository

    Huang, Yu Li

    2015-02-17

    Two-dimensional transition metal dichalcogenides have emerged as a new class of semiconductor materials with novel electronic and optical properties of interest to future nanoelectronics technology. Single-layer molybdenum disulphide, which represents a prototype two-dimensional transition metal dichalcogenide, has an electronic bandgap that increases with decreasing layer thickness. Using high-resolution scanning tunnelling microscopy and spectroscopy, we measure the apparent quasiparticle energy gap to be 2.40±0.05 eV for single-layer, 2.10±0.05 eV for bilayer and 1.75±0.05 eV for trilayer molybdenum disulphide, which were directly grown on a graphite substrate by chemical vapour deposition method. More interestingly, we report an unexpected bandgap tunability (as large as 0.85±0.05 eV) with distance from the grain boundary in single-layer molybdenum disulphide, which also depends on the grain misorientation angle. This work opens up new possibilities for flexible electronic and optoelectronic devices with tunable bandgaps that utilize both the control of two-dimensional layer thickness and the grain boundary engineering.

  18. Study of rapid grain boundary migration in a nanocrystalline Ni thin film

    International Nuclear Information System (INIS)

    Kacher, Josh; Robertson, I.M.; Nowell, Matt; Knapp, J.; Hattar, Khalid

    2011-01-01

    Research highlights: → Abnormal growth is distributed randomly in the foil and initiates at different times. → Growth occurs from seemingly uncorrelated regions of the grain boundary. → Growth twins are created during all stages of abnormal grain growth. → Grain growth patterns are qualitatively similar to a vacancy diffusion model. → Grain boundaries and orientations evolve during growth to minimize system energy. - Abstract: Grain boundary migration associated with abnormal grain growth in pulsed-laser deposited Ni was studied in real time by annealing electron transparent films in situ in the transmission electron microscope. The resulting texture evolution and grain boundary types produced were evaluated by ex situ electron backscatter diffraction of interrupted anneals. The combination of these two techniques allowed for the investigation of grain growth rates, grain morphologies, and the evolution of the orientation and grain boundary distributions. Grain boundaries were found to progress in a sporadic, start/stop fashion with no evidence of a characteristic grain growth rate. The orientations of the abnormally growing grains were found to be predominately //ND throughout the annealing process. A high fraction of twin boundaries developed during the annealing process. The intermittent growth from different locations of the grain boundary is discussed in terms of a vacancy diffusion model for grain growth.

  19. Effect of Trace Levels of Si on Microstructure and Grain Boundary Segregation in DOP-26 Iridium Alloy

    Science.gov (United States)

    Pierce, Dean; Muralidharan, Govindarajan; Heatherly, Lee; Fox, Ethan

    2018-03-01

    The thermodynamics and kinetics of Silicon (Si) segregation to grain boundaries in Iridium alloy DOP-26 with added trace levels of Si of 6, 11, 29, and 36 wppm was studied by Auger Electron Spectroscopy. The four alloys were annealed at 1500 or 1535 °C for 19 or 76 hours followed by cooling at three different rates. Si enrichment at the grain boundaries (GB) increased with increasing bulk Si content, with the grain boundary Si enrichment factors ranging from 62 to 344, depending on the bulk Si content and the cooling rate. Grain boundary Si contents increased with decreasing cooling rate in all alloys, indicating that Si GB segregation is influenced by both thermodynamic and kinetic factors in the alloys and temperature ranges of the study. A Langmuir-McLean isotherm-based model was successfully used to predict the temperature dependence of GB Si segregation in DOP-26 alloys with Si additions and estimate the temperature independent free energy of Si segregation to grain boundaries in DOP-26.

  20. 3D reconstruction of grains in polycrystalline materials using a tessellation model with curved grain boundaries

    Czech Academy of Sciences Publication Activity Database

    Šedivý, Ondřej; Brereton, T.; Westhoff, D.; Polívka, Leoš; Beneš, V.; Schmidt, V.; Jäger, Aleš

    2016-01-01

    Roč. 96, č. 18 (2016), s. 1926-1949 ISSN 1478-6435 R&D Projects: GA ČR GBP108/12/G043; GA MŠk LM2015087 Institutional support: RVO:68378271 Keywords : microstructural characterization * grain boundaries * polycrystalline metals * tessellation modelling * generalised balanced power diagram Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.505, year: 2016

  1. Properties of grain boundaries in BCC iron and iron-based alloys

    Energy Technology Data Exchange (ETDEWEB)

    Terentyev, D.; He, Xinfu

    2010-08-15

    The report contains a summary of work done within the collaboration established between SCK-CEN and CIEA, performed during the internship of Xinfu He (CIAE) in the period of September 2009 to June 2010. In this work, we have carried out an atomistic study addressing the properties of grain boundaries in BCC Fe and Fe-Cr alloys. Throughout this work we report on the structural and cohesive properties of grain boundaries; thermal stability; interaction of grain boundaries with He and diffusivity of He in the core of the grain boundaries; equilibrium segregation of Cr near the grain boundary zone; cleavage fracture of grain boundaries; influence of the Cr precipitates, voids and He bubbles on the structure and strength of grain boundaries.

  2. Grain Boundary Phase Transformations in Nanostructured Conducting Oxides

    Science.gov (United States)

    Straumal, B. B.; Myatiev, A. A.; Straumal, P. B.; Mazilkin, A. A.

    Nanostructured conducting oxides are very promising for various applications like varistors (doped zinc oxide), electrolytes for the solid oxide fuel cells (SOFC) (ceria, zirconia, yttria), semipermeable membranes, and sensors (perovskite-type oxides). Grain boundary (GB) phases crucially determine the properties of nanograined oxides. GB phase transformations (wetting, prewetting, pseudopartial wetting) proceed in the conducting oxides. Novel GB lines appear in the conventional bulk phase diagrams. They can be used for the tailoring of properties of nanograined conducting oxides, particularly by using the novel synthesis method of liquid ceramics.

  3. Stacking fault tetrahedra formation in the neighbourhood of grain boundaries

    CERN Document Server

    Samaras, M; Van Swygenhoven, H; Victoria, M

    2003-01-01

    Large scale molecular dynamics computer simulations are performed to study the role of the grain boundary (GB) during the cascade evolution in irradiated nanocrystalline Ni. At all primary knock-on atom (PKA) energies in cascades near GBs, the damage produced after cooling down is vacancy dominated. Truncated stacking fault tetrahedra (TSFTs) are easily formed at 10 keV and higher PKA energies. At the higher energies a complex partial dislocation network forms, consisting of TSFTs. The GB acts as an interstitial sink without undergoing major structural changes.

  4. Grain boundaries and mechanical properties of nanocrystalline diamond films.

    Energy Technology Data Exchange (ETDEWEB)

    Busmann, H.-G.; Pageler, A.; Gruen, D. M.

    1999-08-06

    Phase-pure nanocrystalline diamond thin films grown from plasmas of a hydrogen-poor carbon argon gas mixture have been analyzed regarding their hardness and elastic moduli by means of a microindentor and a scanning acoustic microscope.The films are superhard and the moduli rival single crystal diamond. In addition, Raman spectroscopy with an excitation wavelength of 1064 nm shows a peak at 1438 l/cm and no peak above 1500 l/cm, and X-ray photoelectron spectroscopy a shake-up loss at 4.2 eV. This gives strong evidence for the existence of solitary double bonds in the films. The hardness and elasticity of the films then are explained by the assumption, that the solitary double bonds interconnect the nanocrystals in the films, leading to an intergrain boundary adhesion of similar strength as the intragrain diamond cohesion. The results are in good agreement with recent simulations of high-energy grain boundaries.

  5. Pressure-induced transition in the grain boundary of diamond

    Science.gov (United States)

    Chen, J.; Tang, L.; Ma, C.; Fan, D.; Yang, B.; Chu, Q.; Yang, W.

    2017-12-01

    Equation of state of diamond powder with different average grain sizes was investigated using in situ synchrotron x-ray diffraction and a diamond anvil cell (DAC). Comparison of compression curves was made for two samples with average grain size of 50nm and 100nm. The two specimens were pre-pressed into pellets and loaded in the sample pressure chamber of the DAC separately to minimized differences of possible systematic errors for the two samples. Neon gas was used as pressure medium and ruby spheres as pressure calibrant. Experiments were conducted at room temperature and high pressures up to 50 GPa. Fitting the compression data in the full pressure range into the third order Birch-Murnaghan equation of state yields bulk modulus (K) and its pressure derivative (K') of 392 GPa and 5.3 for 50nm sample and 398GPa and 4.5 for 100nm sample respectively. Using a simplified core-shell grain model, this result indicates that the grain boundary has an effective bulk modulus of 54 GPa. This value is similar to that observed for carbon nanotube[1] validating the recent theoretical diamond surface modeling[2]. Differential analysis of the compression cures demonstrates clear relative compressibility change at the pressure about 20 GPa. When fit the compression data below and above this pressure separately, the effect of grain size on bulk modulus reverses in the pressure range above 20 GPa. This observation indicates a possible transition of grain boundary structure, likely from sp2 hybridization at the surface[2] towards sp3like orbital structure which behaves alike the inner crystal. [1] Jie Tang, Lu-Chang Qin, Taizo Sasaki, Masako Yudasaka, Akiyuki Matsushita, and Sumio Iijima, Compressibility and Polygonization of Single-Walled Carbon Nanotubes under Hydrostatic Pressure, Physical Review Letters, 85(9), 1187-1198, 2000. [2] Shaohua Lu, Yanchao Wang, Hanyu Liu, Mao-sheng Miao, and Yanming Ma, Self-assembled ultrathin nanotubes on diamond (100) surface, Nature

  6. The influence of the grain boundary structure on diffusional creep

    International Nuclear Information System (INIS)

    Thorsen, P.A.

    1998-05-01

    An experiment was carried out to quantify the deformation in the diffusional creep domain. It was found that material had indisputably been deposited at grain boundaries in tension. A characterisation of 131 boundaries in terms of their misorientation was carried out and this was correlated to the observed deformation. Twin boundaries below a certain limit of deviation from an exact twin misorientation were totally inactive in the deformation. A large qualitative difference was found in the way general boundaries take part in the deformation. The experiments have taken place at Materials Research Department, Risoe National Laboratory at Roskilde. The present thesis has been submitted in partial fulfillment of the requirements for the Ph.D. degree in physics at the Niels Bohr Institute, University of Copenhagen. Besides the results of the creep experiment the thesis contains a description of the theoretical background to diffusional creep models. Also, the results from an investigation of helium bubble formation in an irradiated copper sample is included. (au)

  7. Investigation of slip transfer across HCP grain boundaries with application to cold dwell facet fatigue

    International Nuclear Information System (INIS)

    Zheng, Zebang; Balint, Daniel S.; Dunne, Fionn P.E.

    2017-01-01

    This paper addresses the role of grain boundary slip transfer and thermally-activated discrete dislocation plasticity in the redistribution of grain boundary stresses during cold dwell fatigue in titanium alloys. Atomistic simulations have been utilised to calculate the grain boundary energies for titanium with respect to the misorientation angles. The grain boundary energies are utilised within a thermally-activated discrete dislocation plasticity model incorporating slip transfer controlled by energetic and grain boundary geometrical criteria. The model predicts the grain size effect on the flow strength in Ti alloys. Cold dwell fatigue behaviour in Ti-6242 alloy is investigated and it is shown that significant stress redistribution from soft to hard grains occurs during the stress dwell, which is observed both for grain boundaries for which slip transfer is permitted and inhibited. However, the grain boundary slip penetration is shown to lead to significantly higher hard-grain basal stresses near the grain boundary after dwell, thus exacerbating the load shedding stress compared to an impenetrable grain boundary. The key property controlling the dwell fatigue response is argued to remain the time constant associated with the thermal activation process for dislocation escape, but the slip penetrability is also important and exacerbates the load shedding. The inclusion of a macrozone does not significantly change the conclusions but does potentially lead to the possibility of a larger initial facet.

  8. Grain boundary and grain interior conduction in {gamma}'-Bi{sub 2}MoO{sub 6}

    Energy Technology Data Exchange (ETDEWEB)

    Vera, C.M.C. [Laboratorio de Peliculas Delgadas, Facultad de Ingenieria, Universidad de Buenos Aires, Paseo Colon 850, 1063 Buenos Aires (Argentina)]. E-mail: cvera@fi.uba.ar; Aragon, R. [Laboratorio de Peliculas Delgadas, Facultad de Ingenieria, Universidad de Buenos Aires, Paseo Colon 850, 1063 Buenos Aires (Argentina); CINSO, CONICET, CITEFA, Lasalle 4397, Villa Martelli, Buenos Aires (Argentina)

    2005-07-25

    Impedance spectroscopy of fine grained (<10 {mu}m) {gamma}'-Bi{sub 2}MoO{sub 6} samples, in the frequency range of 0.1 Hz-250 kHz, relevant to sensor applications, up to 800 deg. C, has been used to characterize grain boundary and grain interior contributions to conduction. Above 500 deg. C, the grain boundary contribution is no longer rate limiting and conduction is dominated by the grain interior component. The corresponding activation energies are 0.98 eV for grain boundary and 0.73 eV for grain interior components. The weak dependence of conductivity on oxygen partial pressure below 500 deg. C can be attributed to electrode-electrolyte interface phenomena, whereas the robust response to ethanol is commensurate with changes in intrinsic ionic conductivity.

  9. DEM Simulation of Direct Shear: 2. Grain Boundary and Mineral Grain Strength Component Influence on Shear Rupture

    Science.gov (United States)

    Bewick, R. P.; Kaiser, P. K.; Bawden, W. F.

    2014-09-01

    The influence of mineral grain and grain boundary strength is investigated using a calibrated intact (non-jointed) brittle rock specimen subjected to direct shear with a particle-based distinct element method and its embedded grain-based method. The adopted numerical approach allows one to independently control the grain boundary and mineral grain strength. The investigation reveals that, in direct shear, the normal stress ( σ n) applied to a rock specimen relative to its uniaxial compressive strength (UCS) determines the resulting rupture mechanism, the ultimate rupture zone geometry, and thus its shear stress versus horizontal displacement response. This allows one to develop a rupture matrix based on this controlling parameter (i.e., σ n/UCS). Mineral grain strength reductions result in the lowering of the apparent cohesion intercept of the peak linear Coulomb strength envelope, while grain boundary strength reductions change the peak linear Coulomb strength envelope to a bi-linear or curved shape. The impact of grain boundary strength is only relevant at σ n/UCS ratios 0.17), the influence of weakened grain boundaries is minimized and strength is controlled by that of the mineral grains.

  10. Highly conductive grain boundaries in copper oxide thin films

    Energy Technology Data Exchange (ETDEWEB)

    Deuermeier, Jonas, E-mail: j.deuermeier@campus.fct.unl.pt [Department of Materials Science, Faculty of Science and Technology, i3N/CENIMAT, Universidade NOVA de Lisboa and CEMOP/UNINOVA, Campus de Caparica, 2829-516 Caparica (Portugal); Department of Materials and Earth Sciences, Technische Universität Darmstadt, Jovanka-Bontschits-Straße 2, D-64287 Darmstadt (Germany); Wardenga, Hans F.; Morasch, Jan; Siol, Sebastian; Klein, Andreas, E-mail: aklein@surface.tu-darmstadt.de [Department of Materials and Earth Sciences, Technische Universität Darmstadt, Jovanka-Bontschits-Straße 2, D-64287 Darmstadt (Germany); Nandy, Suman; Calmeiro, Tomás; Martins, Rodrigo; Fortunato, Elvira [Department of Materials Science, Faculty of Science and Technology, i3N/CENIMAT, Universidade NOVA de Lisboa and CEMOP/UNINOVA, Campus de Caparica, 2829-516 Caparica (Portugal)

    2016-06-21

    High conductivity in the off-state and low field-effect mobility compared to bulk properties is widely observed in the p-type thin-film transistors of Cu{sub 2}O, especially when processed at moderate temperature. This work presents results from in situ conductance measurements at thicknesses from sub-nm to around 250 nm with parallel X-ray photoelectron spectroscopy. An enhanced conductivity at low thickness is explained by the occurrence of Cu(II), which is segregated in the grain boundary and locally causes a conductivity similar to CuO, although the surface of the thick film has Cu{sub 2}O stoichiometry. Since grains grow with an increasing film thickness, the effect of an apparent oxygen excess is most pronounced in vicinity to the substrate interface. Electrical properties of Cu{sub 2}O grains are at least partially short-circuited by this effect. The study focuses on properties inherent to copper oxide, although interface effects cannot be ruled out. This non-destructive, bottom-up analysis reveals phenomena which are commonly not observable after device fabrication, but clearly dominate electrical properties of polycrystalline thin films.

  11. Modeling of stresses at grain boundaries with respect to occurrence of stress corrosion cracking

    Energy Technology Data Exchange (ETDEWEB)

    Kozaczek, K.J. [Oak Ridge National Lab., TN (United States); Sinharoy, A.; Ruud, C.O. [Pennsylvania State Univ., University Park, PA (United States); McIlree, A.R. [Electric Power Research Institute, Palo Alto, CA (United States)

    1995-12-31

    The distributions of elastic stresses/strains in the grain boundary regions were studied by the analytical and the finite element models. The grain boundaries represent the sites where stress concentration occurs as a result of discontinuity of elastic properties across the grain boundary and the presence of second phase particles elastically different from the surrounding matrix grains. A quantitative analysis of those stresses for steels and nickel based alloys showed that the stress concentrations in the grain boundary regions are high enough to cause a local microplastic deformation even when the material is in the macroscopic elastic regime. The stress redistribution as a result of such a plastic deformation was discussed.

  12. Low temperature phonon boundary scattering in slightly rough Silicon nanowires

    Science.gov (United States)

    Ghossoub, Marc; Valavala, Krishna; Seong, Myunghoon; Azeredo, Bruno; Sadhu, Jyothi S.; Sinha, Sanjiv

    2013-03-01

    Nanostructured materials have lower thermal conductivities than the bulk and are promising candidates for thermoelectric applications. In particular, measurements on single silicon nanowires show a reduction in thermal conductivity below the Casimir limit. This reduction increases with surface roughness but the trend and its connection to phonon boundary scattering are still elusive. Here, we measure the thermal conductivity of single silicon nanowires fabricated using metal-assisted chemical etching. High resolution TEM imaging shows crystalline wires with slightly rough surfaces. Their statistical correlation lengths (5-15 nm) and RMS heights (0.8-1.5 nm) are in a range where perturbation-based wave scattering theory is still applicable. We use the thermal conductivity data to extract the frequency dependence of phonon boundary scattering at low temperatures (10-40 K) and show agreement with multiple scattering theory. This work provides insight into enhancing the thermoelectric performance of nanostructures.

  13. Achieving Radiation Tolerance through Non-Equilibrium Grain Boundary Structures.

    Science.gov (United States)

    Vetterick, Gregory A; Gruber, Jacob; Suri, Pranav K; Baldwin, Jon K; Kirk, Marquis A; Baldo, Pete; Wang, Yong Q; Misra, Amit; Tucker, Garritt J; Taheri, Mitra L

    2017-09-25

    Many methods used to produce nanocrystalline (NC) materials leave behind non-equilibrium grain boundaries (GBs) containing excess free volume and higher energy than their equilibrium counterparts with identical 5 degrees of freedom. Since non-equilibrium GBs have increased amounts of both strain and free volume, these boundaries may act as more efficient sinks for the excess interstitials and vacancies produced in a material under irradiation as compared to equilibrium GBs. The relative sink strengths of equilibrium and non-equilibrium GBs were explored by comparing the behavior of annealed (equilibrium) and as-deposited (non-equilibrium) NC iron films on irradiation. These results were coupled with atomistic simulations to better reveal the underlying processes occurring on timescales too short to capture using in situ TEM. After irradiation, NC iron with non-equilibrium GBs contains both a smaller number density of defect clusters and a smaller average defect cluster size. Simulations showed that excess free volume contribute to a decreased survival rate of point defects in cascades occurring adjacent to the GB and that these boundaries undergo less dramatic changes in structure upon irradiation. These results suggest that non-equilibrium GBs act as more efficient sinks for defects and could be utilized to create more radiation tolerant materials in future.

  14. Grain boundary character distribution derived from three-dimensional microstructure reconstruction

    International Nuclear Information System (INIS)

    Pirgazi, H; Kestens, L A I

    2015-01-01

    Manual serial sectioning which includes consecutive steps of sample preparation and Electron Back Scattering Diffraction (EBSD) measurement was employed to extract the twodimensional (2D) sections of a pure nickel sample and to reconstruct the three-dimensional (3D) microstructure. A general alignment algorithm based on the minimization of misorientation between two adjacent sections has been developed to accurately align the sections. By employing this alignment algorithm, any in-plane (translational) and rotational misalignment as well as the planparallelity can be corrected. Surface triangulation technique was used to reconstruct the grain boundary surfaces. The Grain Boundary Character Distribution (GBCD) was derived from reconstructed grain boundaries. The results show that a smoother grain boundary plane can be obtained after precise translational and rotational alignment and correction of planparallelity.The relative grain boundary energy was computed as a function of the five grain boundary parameters based on equilibrium at triple lines. The results show that the grain boundary planes carrying a Σ 3 type misorientation are dominantly parallel to the {111} crystal plane, which indicates the presence of coherent twin boundaries. It was observed that coherent Σ 3 type boundaries exhibit the minimum relative grain boundary energy, which is approximately 57% smaller than the average of all Σ 3 boundaries, including also incoherent twin boundaries. (paper)

  15. Grain boundary character distribution derived from three-dimensional microstructure reconstruction

    Science.gov (United States)

    Pirgazi, H.; Kestens, L. A. I.

    2015-04-01

    Manual serial sectioning which includes consecutive steps of sample preparation and Electron Back Scattering Diffraction (EBSD) measurement was employed to extract the twodimensional (2D) sections of a pure nickel sample and to reconstruct the three-dimensional (3D) microstructure. A general alignment algorithm based on the minimization of misorientation between two adjacent sections has been developed to accurately align the sections. By employing this alignment algorithm, any in-plane (translational) and rotational misalignment as well as the planparallelity can be corrected. Surface triangulation technique was used to reconstruct the grain boundary surfaces. The Grain Boundary Character Distribution (GBCD) was derived from reconstructed grain boundaries. The results show that a smoother grain boundary plane can be obtained after precise translational and rotational alignment and correction of planparallelity. The relative grain boundary energy was computed as a function of the five grain boundary parameters based on equilibrium at triple lines. The results show that the grain boundary planes carrying a Σ3 type misorientation are dominantly parallel to the {111} crystal plane, which indicates the presence of coherent twin boundaries. It was observed that coherent Σ3 type boundaries exhibit the minimum relative grain boundary energy, which is approximately 57% smaller than the average of all Σ3 boundaries, including also incoherent twin boundaries.

  16. Grain Boundary Segregation and Intergranular Fracture in Molybdenum

    Science.gov (United States)

    Kumar, A.; Eyre, B. L.

    1980-04-01

    The refractory group VIA metals generally exhibit intergranular brittleness when they are in the recrystallized condition. This causes severe problems in their fabrication and places major limitations on their practical application. The phenomenon, generally referred to as recrystallization embrittlement, results in large increases in the ductile-to-brittle transition temperature and a change in fracture mode in the lower shelf regime from cleavage to intergranular with a significant decrease in ductility. The embrittlement is widely considered to be associated with interstitial impurities but there have been few systematic studies to elucidate their effects. The present paper reports results from a systematic study of segregation and intergranular embrittlement in binary molybdenum-oxygen and ternary molybdenum-oxygen-carbon alloys. The experiments were carried out on 'bamboo' specimens containing a series of identical single grain boundaries traversing their cross-sections. Measurements have been made of the activation energy for oxygen segregation to grain boundaries in the binary molybdenum-oxygen alloys. The influence of carbon additions on the level of oxygen segregation has also been determined. In addition, the influence of oxygen segregation on the energy to fracture has been studied and this has involved quantitative measurements of the work of fracture and the contribution made by plastic deformation. Results from metallographic studies are also presented, showing the effects of segregation on fracture surface topography and dislocation structures immediately adjacent to the fracture surfaces. In discussing the results we consider the thermodynamics of oxygen segregation to grain boundaries and the role played by carbon in inhibiting segregation. It is proposed that carbon either increases the effective solubility of oxygen in molybdenum or acts as a trap for oxygen atoms. In either case the effect is to reduce the driving force for segregation. We also

  17. Segregation of solute elements at grain boundaries in an ultrafine grained Al-Zn-Mg-Cu alloy

    Energy Technology Data Exchange (ETDEWEB)

    Sha, Gang, E-mail: g.sha@usyd.edu.au [Australian Centre for Microscopy and Microanalysis, The University of Sydney, NSW 2006 (Australia); ARC Centre of Excellence for Design in Light Metals, The University of Sydney, NSW 2006 (Australia); Yao, Lan [Australian Centre for Microscopy and Microanalysis, The University of Sydney, NSW 2006 (Australia); Liao, Xiaozhou [School of Aerospace, Mechanical and Mechatronic Engineering, The University of Sydney, NSW 2006 (Australia); Ringer, Simon P. [Australian Centre for Microscopy and Microanalysis, The University of Sydney, NSW 2006 (Australia); ARC Centre of Excellence for Design in Light Metals, The University of Sydney, NSW 2006 (Australia); Chao Duan, Zhi [Departments of Aerospace and Mechanical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089-1453 (United States); Langdon, Terence G. [Departments of Aerospace and Mechanical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089-1453 (United States); Materials Research Group, School of Engineering Sciences, University of Southampton, Southampton SO17 1BJ (United Kingdom)

    2011-05-15

    The solute segregation at grain boundaries (GBs) of an ultrafine grained (UFG) Al-Zn-Mg-Cu alloy processed by equal-channel angular pressing (ECAP) at 200 {sup o}C was characterised using three-dimensional atom probe. Mg and Cu segregate strongly to the grain boundaries. In contrast, Zn does not always show clear segregation and may even show depletion near the grain boundaries. Trace element Si selectively segregates at some GBs. An increase in the number of ECAP passes leads to a decrease in the grain size but an increase in solute segregation at the boundaries. The significant segregation of alloying elements at the boundaries of ultrafine-grained alloys implies that less solutes will be available in the matrix for precipitation with a decrease in the average grain size. -- Research Highlights: {yields} Atom probe tomography has been employed successfully to reveal unique segregation of solutes at ultrafine grained material. {yields} Mg and Cu elements segregated strongly at the grain boundary of an ultrafine grained Al-Zn-Mg-Cu alloy processed by 4-pass and 8-pass ECAP at 200 {sup o}C. Zn frequently depleted at GBs with a Zn depletion region of 7-15 nm in width on one or both sides of the GBs. Only a small fraction (3/13) of GBs were observed with a low level of Zn segregation where the combined Mg and Cu excess is over 3.1 atom/nm{sup 2}. Si appeared selectively segregated at some of the GBs. {yields} The increase in number of ECAP passes from 4 to 8 correlated with the increase in mean level segregation of Mg and Cu for both solute excess and peak concentration. {yields} The change of plane normal of a grain boundary within 30{sup o} only leads to a slight change in the solute segregation level.

  18. Segregation of solute elements at grain boundaries in an ultrafine grained Al-Zn-Mg-Cu alloy

    International Nuclear Information System (INIS)

    Sha, Gang; Yao, Lan; Liao, Xiaozhou; Ringer, Simon P.; Chao Duan, Zhi; Langdon, Terence G.

    2011-01-01

    The solute segregation at grain boundaries (GBs) of an ultrafine grained (UFG) Al-Zn-Mg-Cu alloy processed by equal-channel angular pressing (ECAP) at 200 o C was characterised using three-dimensional atom probe. Mg and Cu segregate strongly to the grain boundaries. In contrast, Zn does not always show clear segregation and may even show depletion near the grain boundaries. Trace element Si selectively segregates at some GBs. An increase in the number of ECAP passes leads to a decrease in the grain size but an increase in solute segregation at the boundaries. The significant segregation of alloying elements at the boundaries of ultrafine-grained alloys implies that less solutes will be available in the matrix for precipitation with a decrease in the average grain size. -- Research Highlights: → Atom probe tomography has been employed successfully to reveal unique segregation of solutes at ultrafine grained material. → Mg and Cu elements segregated strongly at the grain boundary of an ultrafine grained Al-Zn-Mg-Cu alloy processed by 4-pass and 8-pass ECAP at 200 o C. Zn frequently depleted at GBs with a Zn depletion region of 7-15 nm in width on one or both sides of the GBs. Only a small fraction (3/13) of GBs were observed with a low level of Zn segregation where the combined Mg and Cu excess is over 3.1 atom/nm 2 . Si appeared selectively segregated at some of the GBs. → The increase in number of ECAP passes from 4 to 8 correlated with the increase in mean level segregation of Mg and Cu for both solute excess and peak concentration. → The change of plane normal of a grain boundary within 30 o only leads to a slight change in the solute segregation level.

  19. Phonon thermal transport through tilt grain boundaries in strontium titanate

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Zexi; Chen, Xiang; Yang, Shengfeng; Xiong, Liming; Chen, Youping [Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, Florida 32611 (United States); Deng, Bowen; Chernatynskiy, Aleksandr [Department of Materials Science and Engineering, University of Florida, Gainesville, Florida 32611 (United States)

    2014-08-21

    In this work, we perform nonequilibrium molecular dynamics simulations to study phonon scattering at two tilt grain boundaries (GBs) in SrTiO{sub 3}. Mode-wise energy transmission coefficients are obtained based on phonon wave-packet dynamics simulations. The Kapitza conductance is then quantified using a lattice dynamics approach. The obtained results of the Kapitza conductance of both GBs compare well with those obtained by the direct method, except for the temperature dependence. Contrary to common belief, the results of this work show that the optical modes in SrTiO{sub 3} contribute significantly to phonon thermal transport, accounting for over 50% of the Kapitza conductance. To understand the effect of the GB structural disorder on phonon transport, we compare the local phonon density of states of the atoms in the GB region with that in the single crystalline grain region. Our results show that the excess vibrational modes introduced by the structural disorder do not have a significant effect on phonon scattering at the GBs, but the absence of certain modes in the GB region appears to be responsible for phonon reflections at GBs. This work has also demonstrated phonon mode conversion and simultaneous generation of new modes. Some of the new modes have the same frequency as the initial wave packet, while some have the same wave vector but lower frequencies.

  20. Phonon thermal transport through tilt grain boundaries in strontium titanate

    International Nuclear Information System (INIS)

    Zheng, Zexi; Chen, Xiang; Yang, Shengfeng; Xiong, Liming; Chen, Youping; Deng, Bowen; Chernatynskiy, Aleksandr

    2014-01-01

    In this work, we perform nonequilibrium molecular dynamics simulations to study phonon scattering at two tilt grain boundaries (GBs) in SrTiO 3 . Mode-wise energy transmission coefficients are obtained based on phonon wave-packet dynamics simulations. The Kapitza conductance is then quantified using a lattice dynamics approach. The obtained results of the Kapitza conductance of both GBs compare well with those obtained by the direct method, except for the temperature dependence. Contrary to common belief, the results of this work show that the optical modes in SrTiO 3 contribute significantly to phonon thermal transport, accounting for over 50% of the Kapitza conductance. To understand the effect of the GB structural disorder on phonon transport, we compare the local phonon density of states of the atoms in the GB region with that in the single crystalline grain region. Our results show that the excess vibrational modes introduced by the structural disorder do not have a significant effect on phonon scattering at the GBs, but the absence of certain modes in the GB region appears to be responsible for phonon reflections at GBs. This work has also demonstrated phonon mode conversion and simultaneous generation of new modes. Some of the new modes have the same frequency as the initial wave packet, while some have the same wave vector but lower frequencies

  1. Thermodynamics of grain boundary premelting in alloys. II. Atomistic simulation

    International Nuclear Information System (INIS)

    Williams, P.L.; Mishin, Y.

    2009-01-01

    We apply the semi-grand-canonical Monte Carlo method with an embedded-atom potential to study grain boundary (GB) premelting in Cu-rich Cu-Ag alloys. The Σ5 GB chosen for this study becomes increasingly disordered near the solidus line while its local chemical composition approaches the liquidus composition at the same temperature. This behavior indicates the formation of a thin layer of the liquid phase in the GB when the grain composition approaches the solidus. The thickness of the liquid layer remains finite and the GB can be overheated/oversaturated to metastable states slightly above the solidus. The premelting behavior found by the simulations is qualitatively consistent with the phase-field model of the same binary system presented in Part I of this work [Mishin Y, Boettinger WJ, Warren JA, McFadden GB. Acta Mater, in press]. Although this agreement is encouraging, we discuss several problems arising when atomistic simulations are compared with phase-field modeling.

  2. Electrical properties of grain boundaries in polycrystalline materials under intrinsic or low doping

    International Nuclear Information System (INIS)

    Chowdhury, M H; Kabir, M Z

    2011-01-01

    An analytical model is developed to study the electrical properties (electric field and potential distributions, potential energy barrier height and polarization phenomenon) of polycrystalline materials at intrinsic or low doping for detector and solar cell applications by considering an arbitrary amount of grain boundary charge and a finite width of grain boundary region. The general grain boundary model is also applicable to highly doped polycrystalline materials. The electric field and potential distributions are obtained by solving Poisson's equation in both depleted grains and grain boundary regions. The electric field and potential distributions across the detector are analysed under various doping, trapping and applied biases. The electric field collapses, i.e. a nearly zero-average electric field region exists in some part of the biased detector at high trapped charge densities at the grain boundaries. The model explains the conditions of existence of a zero-average field region, i.e. the polarization mechanisms in polycrystalline materials. The potential energy barrier at the grain boundary exists if the electric field changes its sign at the opposite side of the grain boundary. The energy barrier does not exist in all grain boundaries in the low-doped polycrystalline detector and it never exists in intrinsic polycrystalline detectors under applied bias condition provided that there is no charge trapping in the grain.

  3. Chevron defect at the intersection of grain boundaries with free surfaces in Au

    International Nuclear Information System (INIS)

    Radetic, T.; Lancon, F.; Dahmen, U.

    2002-01-01

    We have identified a new defect at the intersection between grain boundaries and surfaces in Au using atomic resolution transmission electron microscopy. At the junction line of 90 deg. tilt grain boundaries of (110)-(001) orientation with the free surface, a small segment of the grain boundary, about 1 nm in length, dissociates into a triangular region with a chevronlike stacking disorder and a distorted hcp structure. The structure and stability of these defects are confirmed by atomistic simulations, and we point out the relationship with the one-dimensional incommensurate structure of the grain boundary

  4. Grain Boundary Engineering for Assessing Durability and Aging Issues with Nickel-Based Superalloys, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — The Grain Boundary Engineering (GBE) approach, successfully demonstrated in Phase I, that microstructural optimization provides a very significant improvement in...

  5. Grain Boundary Engineering for Assessing Durability and Aging Issues with Nickel-Based Superalloys Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Grain Boundary Engineering (GBE) approach, successfully demonstrated in Phase I, that microstructural optimization provides a very significant improvement in...

  6. Local and bulk melting of Cu at grain boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Shengnian [Los Alamos National Laboratory; Han, Li - Bo [USTC; An, Qi [USTC/CALTECH; Fu, Rong - Shan [USTC; Zheng, Lianqing [FSU

    2008-01-01

    We investigate gain boundary (GB) melting using molecular dynamics simulations on face-centered-cubic Cu bicrystals with symmetric {l_angle}110{r_angle} tilt grain boundaries. Two representative types of GBs are explored: {Sigma} = 11/(113)/50.48{sup o} (low GB energy) and {Sigma} = 27/(552)/148.41{sup o} (high GB energy). The temperature and temporal evolutions of the Cu bicrystals under stepped heating are characterized in terms of order parameters and diffusion coefficients, as ell as the nucleation and growth of melt. Within the GB region, continuous local melting precedes discontinuous bulk melting, while continuous solid state disordering may precede local melting. Premelting may occur for local melting but not for bulk melting. For {Sigma} = 11/(113)/50.48{sup o}, premelting of the GB region is negligible, and local melting occurs near the thermodynamic melting temperature. The GB region as a whole is superheated by about 13% before its bulk melting. In the case of {Sigma} = 27/(552)/148.41, considerable premelting is observed for local melting, while the bulk melting occurs with negligible superheating. The exact melting behavior of a general GB depends on the GB energy, but is likely bracketed within these two cases.

  7. Multi-phase-field study of the effects of anisotropic grain-boundary properties on polycrystalline grain growth

    Science.gov (United States)

    Miyoshi, Eisuke; Takaki, Tomohiro

    2017-09-01

    Numerical studies of the effects of anisotropic (misorientation-dependent) grain-boundary energy and mobility on polycrystalline grain growth have been carried out for decades. However, conclusive knowledge has yet to be obtained even for the simplest two-dimensional case, which is mainly due to limitations in the computational accuracy of the grain-growth models and computer resources that have been employed to date. Our study attempts to address these problems by utilizing a higher-order multi-phase-field (MPF) model, which was developed to accurately simulate grain growth with anisotropic grain-boundary properties. In addition, we also employ general-purpose computing on graphics processing units to accelerate MPF grain-growth simulations. Through a series of simulations of anisotropic grain growth, we succeeded in confirming that both the anisotropies in grain-boundary energy and mobility affect the morphology formed during grain growth. On the other hand, we found the grain growth kinetics in anisotropic systems to follow parabolic law similar to isotropic growth, but only after an initial transient period.

  8. Grain boundary engineering for control of tellurium diffusion in GH3535 alloy

    Science.gov (United States)

    Fu, Cai-Tao; Yinling, Wang; Chu, Xiang-Wei; Jiang, Li; Zhang, Wen-Zhu; Bai, Qin; Xia, Shuang; Leng, Bin; Li, Zhi-Jun; Ye, Xiang-Xi; Liu, Fang

    2017-12-01

    The effect of grain boundary engineering (GBE) on the Te diffusion along the surface grain boundaries was investigated in GH3535 alloy. It can be found that GBE treatment increases obviously the fraction of low-Σ coincidence site lattice (CSL) boundaries, especially the Σ3 ones, and introduces the large-size grain clusters. When the as-received (AR) and GBE-treated (GBET) specimens were exposed to Te vapor, only Σ3 boundaries were found to be resistant to Te diffusion. From the cross section and the surface, the fewer Te-attacked grain boundaries and the thinner corrosion layer can be observed in the GBET sample. The improvement of resistance to Te diffusion in the GBET sample can be attributed to the large size grain-clusters associated with high proportion of the Σ3n boundaries.

  9. Misorientation related microstructure at the grain boundary in a nickel-based single crystal superalloy

    International Nuclear Information System (INIS)

    Huang, Ming; Zhuo, Longchao; Liu, Zhanli; Lu, Xiaogang; Shi, Zhenxue; Li, Jiarong; Zhu, Jing

    2015-01-01

    The mechanical properties of nickel-based single crystal superalloys deteriorate with increasing misorientation, thus the finished product rate of the casting of single crystal turbine airfoils may be reduced due to the formation of grain boundaries especially when the misorientation angle exceeds to some extent. To this day, evolution of the microstructures at the grain boundaries with misorientation and the relationship between the microstructures and the mechanical properties are still unclear. In this work a detailed characterization of the misorientation related microstructure at the grain boundary in DD6 single crystal superalloy has been carried out using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques; the elemental distribution at the grain boundaries has been analyzed by energy dispersive (EDS) X-ray mapping; and the effect of precipitation of μ phases at the grain boundary on the mechanical property has been evaluated by finite element calculation. It is shown that the proportion of γ phase at the grain boundaries decreases, while the proportion of γ′ phase at the grain boundaries increases with increasing misorientation; the μ phase is precipitated at the grain boundaries when the misorientation angle exceeds about 10° and thus it could lead to a dramatic deterioration of the mechanical properties, as well as that the enrichment of Re and W gradually disappears as the misorientation angle increases. All these factors may result in the degradation of the mechanical properties at the grain boundaries as the misorientation increases. Furthermore, the finite element calculation confirms that precipitation of μ phases at the grain boundary is responsible for the significant deterioration of the mechanical properties when the misorientation exceeds about 10°. This work provides a physical imaging of the microstructure for understanding the relationship between the mechanical properties and the misorientation

  10. The structure and composition of olivine grain boundaries: 40 years of studies, status and current developments

    Science.gov (United States)

    Marquardt, K.; Faul, U. H.

    2018-02-01

    Interfaces in rocks, especially grain boundaries in olivine dominated rocks, have been subject to about 40 years of studies. The grain boundary structure to property relation is fundamental to understand the diverging properties of polycrystalline samples compared to those of single crystals. The number of direct structural observations is small, i.e. in range of 100 micrographs, and the number of measurements of properties directly linked to structural observations is even smaller. Bulk aggregate properties, such as seismic attenuation, rheology and electrical conductivity, are sensitive to grain size, and seem to show influences by grain boundary character distributions. In this context we review previous studies on grain boundary structure and composition and plausible relations to bulk properties. The grain boundary geometry is described using five independent parameters; generally, their structural width ranges between 0.4-1.2 nm and the commonly used 1 nm seems a good approximation. This region of enhanced disorder is often enriched in elements that are incompatible in the perfect crystal lattice. The chemical composition of grain boundaries depends on the bulk rock composition. We determined the 5 parameter grain boundary character distribution (GBCD) for polycrystaline Fo_{90} and studied structure and chemistry at the nm-scale to extend previous measurements. We find that grain boundary planes close to perpendicular to the crystallographic c-direction dominate the grain boundary network. We conclude that linking grain boundary structure in its full geometric parameter space to variations of bulk rock properties is now possible by GBCD determination using EBSD mapping and statistical analyses.

  11. Improvement of creep-rupture properties by serrated grain boundaries in high-tungsten cobalt-base superalloys

    International Nuclear Information System (INIS)

    Tanaka, Manabu

    1993-01-01

    The improvement of creep-rupture properties by serrated grain boundaries was investigated using cobalt-base superalloys containing about 14 to 20 wt.% tungsten at 1089 and 1311 K. Serrated grain boundaries improved both the rupture life and the ductility, especially under lower stresses at 1089 K. The increase in rupture life was larger in the alloys containing a larger amount of W. Ductile grain boundary fracture surfaces, which involved dimple patterns and grain boundary ledges, were observed in the specimens with serrated grain boundaries whereas brittle grain boundary facets were observed in the specimens with normal straight grain boundaries ruptured at 1089 K. The strengthening by serrated grain boundaries was also effective at 1311 K, but there was little difference in rupture life between the specimens with serrated grain boundaries and those with straight grain boundaries under lower stresses, since serrated grain boundaries developed also in the specimens with straight grain boundaries according to grain boundary precipitates forming during creep at 1311 K. The increase in W content of the alloys led to the increase in rupture life of the specimens with serrated grain boundaries at 1089 and 1311 K. (orig.) [de

  12. A Generalized Finite Element Method for polycrystals with discontinuous grain boundaries

    NARCIS (Netherlands)

    Simone, A.; Duarte, C. A.; Van der Giessen, E.

    2006-01-01

    We present a Generalized Finite Element Method for the analysis of polycrystals with explicit treatment of grain boundaries. Grain boundaries and junctions, understood as loci of possible displacement discontinuity, are inserted into finite elements by exploiting the partition of unity property of

  13. Theory and computerized simulation of interaction of point defects with grain boundaries

    International Nuclear Information System (INIS)

    Bojko, V.S.

    1987-01-01

    The issued results on mathematical simulation at the atomic level of formation and migration of point defects arising under radiation (of intrinsic point defects, helium atoms) in the region of grain boundary are analyzed. Simulation data on impurity atom interaction with grain boundaries are also considered

  14. Expansion and Automation of the Energy Conserving Orientational Force for Calculation of Grain Boundary Mobility

    Science.gov (United States)

    2018-02-21

    ARL-TR-8302 ● FEB 2018 US Army Research Laboratory Expansion and Automation of the Energy Conserving Orientational Force for...US Army Research Laboratory Expansion and Automation of the Energy Conserving Orientational Force for Calculation of Grain Boundary...TITLE AND SUBTITLE Expansion and Automation of the Energy Conserving Orientational Force for Calculation of Grain Boundary Mobility 5a. CONTRACT

  15. Microstructural effects on grain boundary motion in Al-Mn alloys

    NARCIS (Netherlands)

    Anselmino, E.

    2007-01-01

    Despite the importance of grain boundary migration during recrystallisation in metals, the details of the mechanism are not well known and there are few direct and accurate experimental observations. The main scope of this thesis is therefore to study the local grain boundary motion in an Al-Mn

  16. Grain boundaries of nanocrystalline materials - their widths, compositions, and internal structures

    International Nuclear Information System (INIS)

    Fultz, B.; Frase, H.N.

    2000-01-01

    Nanocrystalline materials contain many atoms at and near grain boundaries. Sufficient numbers of Moessbauer probe atoms can be situated in grain boundary environments to make a clear contribution to the measured Moessbauer spectrum. Three types of measurements on nanocrystalline materials are reported here, all using Moessbauer spectrometry in conjunction with X-ray diffractometry, transmission electron microscopy, or small angle neutron scattering. By measuring the fraction of atoms contributing to the grain boundary component in a Moessbauer spectrum, and by knowing the grain size of the material, it is possible to deduce the average width of grain boundaries in metallic alloys. It is found that these widths are approximately 0.5 nm for fcc alloys and slightly larger than 1.0 nm for bcc alloys.Chemical segregation to grain boundaries can be measured by Moessbauer spectrometry, especially in conjunction with small angle neutron scattering. Such measurements on Fe-Cu and Fe 3 Si-Nb were used to study how nanocrystalline materials could be stabilized against grain growth by the segregation of Cu and Nb to grain boundaries. The segregation of Cu to grain boundaries did not stabilize the Fe-Cu alloys against grain growth, since the grain boundaries were found to widen and accept more Cu atoms during annealing. The Nb additions to Fe 3 Si did suppress grain growth, perhaps because of the low mobility of Nb atoms, but also perhaps because Nb atoms altered the chemical ordering in the alloy.The internal structure of grain boundaries in nanocrystalline materials prepared by high-energy ball milling is found to be unstable against internal relaxations at low temperatures. The Moessbauer spectra of the nanocrystalline samples showed changes in the hyperfine fields attributable to movements of grain boundary atoms. In conjunction with SANS measurements, the changes in grain boundary structure induced by cryogenic exposure and annealing at low temperature were found to be

  17. Grain boundary diffusion and segregation of Ni in Cu

    International Nuclear Information System (INIS)

    Divinski, Sergiy; Ribbe, Jens; Schmitz, Guido; Herzig, Christian

    2007-01-01

    Grain boundary (GB) diffusion of 63 Ni in polycrystalline Cu was investigated by the radiotracer technique in an extended temperature interval from 476 to 1156K. The independent measurements in Harrison's C and B kinetic regimes resulted in direct data of the GB diffusivity D gb and of the so-called triple product P=s.δ.D gb (s and δ are the segregation factor and the diffusional GB width, respectively). Arrhenius-type temperature dependencies for both the D gb and P values were measured, resulting in the pre-exponential factors D gb 0 =6.93x10 -7 m 2 s -1 and P 0 =1.89x10 -16 m 3 s -1 and the activation enthalpies of 90.4 and 73.8kJmol -1 , respectively. Although Ni is completely soluble in Cu, it reveals a distinct but still moderate ability to segregate copper GBs with a segregation enthalpy of about -17kJmol -1

  18. Hydrogen diffusion along grain boundaries in erbium oxide coatings

    International Nuclear Information System (INIS)

    Mao, Wei; Chikada, Takumi; Suzuki, Akihiro; Terai, Takayuki

    2014-01-01

    Diffusion of interstitial atomic hydrogen in erbium oxide (Er 2 O 3 ) was investigated using density functional theory (DFT) and molecular dynamics (MD) methods. Hydrogen diffusivity in bulk, on (0 0 1) surface, and along Σ13 (4–3–1)/[1 1 1] symmetric tilt grain boundaries (GBs) were evaluated in a temperature range of 673–1073 K, as well as hydrogen diffusion barriers. It was found that H diffusion shows the faster on (0 0 1) surface than along GBs and in bulk. Also, energy barrier of H diffusion in bulk estimated by DFT and MD methods is somewhat higher than that along GBs evaluated in the experiments. This suggests that H diffusion in Er 2 O 3 coatings depends on GBs rather than bulk. In addition, with a correction of GB density, the simulated diffusivity along GBs in MD simulations is in good agreement with the experimental data within one order of magnitude. The discrepancy of H diffusivity between the experiments and the simulations should be reduced by considering H concentration, H diffusion direction, deviations of the initial configuration, vacancy defects, etc

  19. Modeling of grain boundary stresses in Alloy 600

    Energy Technology Data Exchange (ETDEWEB)

    Kozaczek, K.J. [Oak Ridge National Lab., TN (United States); Sinharoy, A.; Ruud, C.O. [Pennsylvania State Univ., University Park, PA (United States); Mcllree, A.R. [Electric Power Research Inst., Palo Alto, CA (United States)

    1995-04-01

    Corrosive environments combined with high stress levels and susceptible microstructures can cause intergranular stress corrosion cracking (IGSCC) of Alloy 600 components on both primary and secondary sides of pressurized water reactors. One factor affecting the IGSCC is intergranular carbide precipitation controlled by heat treatment of Alloy 600. This study is concerned with analysis of elastic stress fields in vicinity of M{sub 7}C{sub 3} and M{sub 23}C{sub 6} carbides precipitated in the matrix and at a grain boundary triple point. The local stress concentration which can lead to IGSCC initiation was studied using a two-dimensional finite element model. The intergranular precipitates are more effective stress raisers than the intragranular precipitates. The combination of the elastic property mismatch and the precipitate shape can result in a local stress field substantially different than the macroscopic stress. The maximum local stresses in the vicinity of the intergranular precipitate were almost twice as high as the applied stress.

  20. Grain-Boundary Resistance in Copper Interconnects: From an Atomistic Model to a Neural Network

    Science.gov (United States)

    Valencia, Daniel; Wilson, Evan; Jiang, Zhengping; Valencia-Zapata, Gustavo A.; Wang, Kuang-Chung; Klimeck, Gerhard; Povolotskyi, Michael

    2018-04-01

    Orientation effects on the specific resistance of copper grain boundaries are studied systematically with two different atomistic tight-binding methods. A methodology is developed to model the specific resistance of grain boundaries in the ballistic limit using the embedded atom model, tight- binding methods, and nonequilibrium Green's functions. The methodology is validated against first-principles calculations for thin films with a single coincident grain boundary, with 6.4% deviation in the specific resistance. A statistical ensemble of 600 large, random structures with grains is studied. For structures with three grains, it is found that the distribution of specific resistances is close to normal. Finally, a compact model for grain-boundary-specific resistance is constructed based on a neural network.

  1. Effective search for stable segregation configurations at grain boundaries with data-mining techniques

    Science.gov (United States)

    Kiyohara, Shin; Mizoguchi, Teruyasu

    2018-03-01

    Grain boundary segregation of dopants plays a crucial role in materials properties. To investigate the dopant segregation behavior at the grain boundary, an enormous number of combinations have to be considered in the segregation of multiple dopants at the complex grain boundary structures. Here, two data mining techniques, the random-forests regression and the genetic algorithm, were applied to determine stable segregation sites at grain boundaries efficiently. Using the random-forests method, a predictive model was constructed from 2% of the segregation configurations and it has been shown that this model could determine the stable segregation configurations. Furthermore, the genetic algorithm also successfully determined the most stable segregation configuration with great efficiency. We demonstrate that these approaches are quite effective to investigate the dopant segregation behaviors at grain boundaries.

  2. Effects of Grain Boundary Morphologies on Stress Corrosion Cracking of Alloy 600

    Directory of Open Access Journals (Sweden)

    Kim H.P.

    2017-06-01

    Full Text Available Effects of grain boundary morphologies on stress corrosion cracking (SCC of Alloy 600 have been studied in 40% NaOH at 315°C using C-ring specimens. The configuration of the grain boundary and the intergranular carbide density were controlled by heat treatment. SCC tests were performed at +150 mV above the corrosion potential. The specimen with a serrated grain boundary showed higher SCC resistance than that with a straight grain boundary. This appears to be caused by the fact that the specimen with the serrated grain boundary has longer SCC path. SCC resistance also increased with intergranular carbide density probably due to enhanced relaxation of stress at intergranular carbide.

  3. Effect of irradiation on mechanical properties of symmetrical grain boundaries investigated by atomic simulations

    Energy Technology Data Exchange (ETDEWEB)

    Wang, X. Y.; Gao, N.; Setyawan, W.; Xu, B.; Liu, W.; Wang, Z. G.

    2017-08-01

    Tensile response of irradiated symmetric grain boundaries to externally applied strain has been studied using atomic simulation methods. The absorption of irradiation induced defects by grain boundaries has been confirmed to degrade the mechanical properties of grain boundaries through the change of its under- taken deformation mechanism. Atomic rearrangement, the formations of a stress accumulation region and vacancy-rich zone and the nucleation and movement of dislocations under stress effect have been observed after the displacement cascades in grain boundaries, which are considered as main reasons to induce above degradation. These results suggest the necessity of considering both trap- ping efficiency to defects and the mechanical property change of irradiated grain boundaries for further development of radiation resistant materials.

  4. Structure and transport at grain boundaries in polycrystalline olivine: An atomic-scale perspective

    Science.gov (United States)

    Mantisi, Boris; Sator, Nicolas; Guillot, Bertrand

    2017-12-01

    Structure and transport properties at grain boundaries in polycrystalline olivine have been investigated at the atomic scale by molecular dynamics simulation (MD) using an empirical ionocovalent interaction potential. On the time scale of the simulation (a few tens of nanoseconds for a system size of ∼650,000 atoms) grain boundaries and grain interior were identified by mapping the atomic displacements along the simulation run. In the investigated temperature range (1300-1700 K) the mean thickness of the grain boundary phase is evaluated between 0.5 and 2 nm, a value which depends on temperature and grain size. The structure of the grain boundary phase is found to be disordered (amorphous-like) and is different from the one exhibited by the supercooled liquid. The self-diffusion coefficients of major elements in the intergranular region range from ∼10-13 to 10-10 m2/s between 1300 and 1700 K (with DSigb viscosity has been evaluated from the Green-Kubo relation expressing the viscosity as function of the stress tensor time correlation function. In spite of a slow convergence of the calculation by MD, the grain boundary viscosity was estimated about ∼105 Pa s at 1500 K, a value in agreement with high-temperature viscoelastic relaxation data. An interesting information gained from MD is that sliding at grain boundaries is essentially controlled by the internal friction between the intergranular phase and the grain edges.

  5. Investigation of 63Ni diffusion along stationary and moving grain boundaries in Nb

    International Nuclear Information System (INIS)

    Razumovskii, I.M.; Mishin, Yu.; Herzig, C.

    1996-01-01

    Grain boundary diffusion of 63 Ni in high purity polycrystalline niobium has been studied in the temperature range 973-1258 K by the radiotracer serial sectioning technique. Since the grain size in the material could not be completely stabilized by pre-diffusion heat treatment, some part of the grain boundaries could migrate during the diffusion anneals. The tracer penetration profiles were treated using the model of diffusion in polycrystals containing both stationary and moving grain boundaries developed in our previous work. Along with the grain boundary diffusivity, also the average velocity of moving grain boundaries and the activation energy of boundary migration in Nb were determined from the effect of boundary motion on the profile shape. Grain boundary diffusion of Ni in Nb is anomalously fast and exhibits an activation energy of 155.2 kJ mol -1 . This behaviour is well consistent with that of Co diffusion in Nb studied previously and implies that diffusion of both elements in Nb is governed by a combined atomic mechanism involving both vacancies and interstitials. (orig.)

  6. Atom probe study of grain boundary segregation in technically pure molybdenum

    International Nuclear Information System (INIS)

    Babinsky, K.; Weidow, J.; Knabl, W.; Lorich, A.; Leitner, H.; Primig, S.

    2014-01-01

    Molybdenum, a metal with excellent physical, chemical and high-temperature properties, is an interesting material for applications in lighting-technology, high performance electronics, high temperature furnace construction and coating technology. However, its applicability as a structural material is limited because of the poor oxidation resistance at high temperatures and a brittle-to-ductile transition around room temperature, which is influenced by the grain size and the content of interstitial impurities at the grain boundaries. Due to the progress of the powder metallurgical production during the last decades, the amount of impurities in the current quality of molybdenum has become so small that surface sensitive techniques are not applicable anymore. Therefore, the atom probe, which allows the detection of small amounts of impurities as well as their location, seems to be a more suitable technique. However, a site-specific specimen preparation procedure for grain boundaries in refractory metals with a dual focused ion beam/scanning electron microscope is still required. The present investigation describes the development and successful application of such a site-specific preparation technique for grain boundaries in molybdenum, which is significantly improved by a combination with transmission electron microscopy. This complimentary technique helps to improve the visibility of grain boundaries during the last preparation steps and to evidence the presence of grain and subgrain boundaries without segregants in atom probe specimens. Furthermore, in industrially processed and recrystallized molybdenum sheets grain boundary segregation of oxygen, nitrogen and potassium is successfully detected close to segregated regions which are believed to be former sinter pores. - Highlights: • First study of grain boundary segregation in molybdenum by atom probe • Site-specific preparation technique by FIB and TEM successfully developed • Grain boundary segregation of

  7. Grain boundary sliding quantification by atomic force microscopy: contribution to high temperature embrittlement analyses

    International Nuclear Information System (INIS)

    Lenci, Matthieu

    2009-01-01

    We developed an original experimental method for measuring grain boundary sliding by atomic force microscopy. The analysed alloys were previously tested at high temperatures and low strain rates, for short time tests. We measured grain boundary sliding along his perpendicular component to the sample surface. The detection limit is of 10 nm. Thin and flat austenitic stainless steels and superalloys samples were tested at high temperature (360 C to 750 C), under ultra high vacuum atmosphere, with slow rate tensile tests and constant load tests. After short times tests, AFM characterization showed that grain boundary sliding could be activated at the loading, within amplitudes of several tens of nm. Furthermore, after short time tests, grain boundary sliding amplitudes are independent of the geometrical orientation of the boundary trace compared with loading direction. On the other hand crystallographic misorientation has a strong influence on boundaries propensity to slide. Intergranular segregation was also analyzed by AES for two alloys (304H austenitic stainless steel and X- 750 nickel-base alloy), previously submitted to high temperature slow strain rate tensile tests. AES analysis showed preferential segregation of S and P near 304H triple junctions. Whereas, AES analysis on X-750 alloy showed P segregation at the bottom of microvoids distributed on a micro-ductile grain facet and a strong segregation of S at the location of grain boundary precipitate. Our experimental methods allows the study of the correlation between two main phenomena contributing to high temperature embrittlement: grain boundary sliding and intergranular segregation embrittlement. Determining grain boundary sliding kinetics should confirm our method of step measure by AFM as a way to indicate high temperature embrittlement sensitivity of alloys in service conditions and also give information about the contribution of grain boundary sliding to stress corrosion cracking initiation and

  8. Ferromagnetic behaviour of ZnO: the role of grain boundaries

    Directory of Open Access Journals (Sweden)

    Boris B. Straumal

    2016-12-01

    Full Text Available The possibility to attain ferromagnetic properties in transparent semiconductor oxides such as ZnO is very promising for future spintronic applications. We demonstrate in this review that ferromagnetism is not an intrinsic property of the ZnO crystalline lattice but is that of ZnO/ZnO grain boundaries. If a ZnO polycrystal contains enough grain boundaries, it can transform into the ferromagnetic state even without doping with “magnetic atoms” such as Mn, Co, Fe or Ni. However, such doping facilitates the appearance of ferromagnetism in ZnO. It increases the saturation magnetisation and decreases the critical amount of grain boundaries needed for FM. A drastic increase of the total solubility of dopants in ZnO with decreasing grain size has been also observed. It is explained by the multilayer grain boundary segregation.

  9. Simultaneous three-dimensional imaging and manipulation of grain boundaries in colloidal crystals

    Science.gov (United States)

    Edmond, Kazem V.; Liu, Yanyan; Curran, Arran; Aarts, Dirk G. A. L.; Sacanna, Stefano; Dullens, Roel P. A.

    Characterizing the properties of grains and grain boundaries is critical for understanding and controlling material properties. We investigate the dynamics of grain boundaries in crystalline materials using concentrated colloidal suspensions of microspheres. The micron-sized particles are suspended in a mixture of solvents whose refractive index and density nearly match those of the particles, enabling three-dimensional visualization and negating gravitational effects. Throughout the sample we disperse specially designed core-shell particles whose cores have a higher refractive index that can be optically trapped. Via optical tweezing, these core-shell particles enable us to directly interact with and probe grain boundaries in 3D within the colloidal crystal. We use a uniquely developed optical microscopy system that combines confocal imaging with holographic trapping, enabling quantitative imaging and precise manipulation simultaneously in three dimensions. Our experiments provide direct insight into the properties of grain boundaries in crystals.

  10. Mapping grain boundary heterogeneity at the nanoscale in a positive temperature coefficient of resistivity ceramic

    Directory of Open Access Journals (Sweden)

    Kristina M. Holsgrove

    2017-06-01

    Full Text Available Despite being of wide commercial use in devices, the orders of magnitude increase in resistance that can be seen in some semiconducting BaTiO3-based ceramics, on heating through the Curie temperature (TC, is far from well understood. Current understanding of the behavior hinges on the role of grain boundary resistance that can be modified by polarization discontinuities which develop in the ferroelectric state. However, direct nanoscale resistance mapping to verify this model has rarely been attempted, and the potential approach to engineer polarization states at the grain boundaries, that could lead to optimized positive temperature coefficient (PTC behavior, is strongly underdeveloped. Here we present direct visualization and nanoscale mapping in a commercially optimized BaTiO3–PbTiO3–CaTiO3 PTC ceramic using Kelvin probe force microscopy, which shows that, even in the low resistance ferroelectric state, the potential drop at grain boundaries is significantly greater than in grain interiors. Aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy reveal new evidence of Pb-rich grain boundaries symptomatic of a higher net polarization normal to the grain boundaries compared to the purer grain interiors. These results validate the critical link between optimized PTC performance and higher local polarization at grain boundaries in this specific ceramic system and suggest a novel route towards engineering devices where an interface layer of higher spontaneous polarization could lead to enhanced PTC functionality.

  11. Grain-boundary microchemistry and intergranular cracking of irradiated austenitic stainless steels

    International Nuclear Information System (INIS)

    Chung, H.M.; Ruther, W.E.; Sanecki, J.E.; Kassner, T.F.

    1993-01-01

    Constant-extension-rate tensile tests and grain-boundary analysis by Auger electron spectroscopy were conducted on high and commercial-purity (HP and CP) Type 304 stainless steel (SS) specimens from irradiated boiling-water reactor (BWR) components to identify the mechanisms of irradiation-assisted stress corrosion cracking (IASCC). Contrary to previous beliefs, susceptibility to intergranular fracture could not be correlated with radiation-induced segregation of impurities such as Si, P, C, or S, but a correlation was obtained with grain-boundary Cr concentration, indicating a role for Cr depletion. Detailed analysis of grain-boundary chemistry was conducted on BWR neutron absorber tubes that were fabricated from two similar heats of HP Type 304 SS of virtually identical bulk chemical composition but exhibiting a significant difference in susceptibility to IASCC after irradiation to ∼2 x 10 21 n/cm 2 (E > 1 MeV). Grain-boundary concentrations of Cr Ni, Si, P, S, and C of the cracking-resistant and -susceptible HP heats were virtually identical. However, grain boundaries of the cracking-resistant material contained less N and more B and Li than those of the cracking-susceptible material. This observation indicates that, besides the deleterious effect of grain-boundary Cr depletion, a synergism between grain-boundary segregation of N and B and transmutation to H and Li plays an important role in IASCC

  12. Influence of grain boundaries on elasticity and thermal conductivity of nanocrystalline diamond films

    International Nuclear Information System (INIS)

    Mohr, Markus; Daccache, Layal; Horvat, Sebastian; Brühne, Kai; Jacob, Timo; Fecht, Hans-Jörg

    2017-01-01

    Diamond combines several outstanding material properties such as the highest thermal conductivity and highest elastic moduli of all materials. This makes diamond an interesting candidate for a multitude of applications. Nonetheless, nanocrystalline diamond films, layers and coatings, usually show properties different to those of single crystalline diamond. This is usually attributed to the larger volume fraction of the grain boundaries with atomic structure different from the single crystal. In this work we measured Young's modulus and thermal conductivity of nanocrystalline diamond films with average grain sizes ranging from 6 to 15 nm. The measured thermal conductivities are modeled considering the thermal boundary conductance between grains as well as a grain size effect on the phonon mean free path. We make a comparison between elastic modulus and thermal boundary conductance of the grain boundaries G k for different nanocrystalline diamond films. We conclude that the grain boundaries thermal boundary conductance G k is a measure of the cohesive energy of the grain boundaries and therefore also of the elastic modulus of the nanocrystalline diamond films.

  13. Surface transition on ice induced by the formation of a grain boundary.

    Directory of Open Access Journals (Sweden)

    Christian Pedersen

    Full Text Available Interfaces between individual ice crystals, usually referred to as grain boundaries, play an important part in many processes in nature. Grain boundary properties are, for example, governing the sintering processes in snow and ice which transform a snowpack into a glacier. In the case of snow sintering, it has been assumed that there are no variations in surface roughness and surface melting, when considering the ice-air interface of an individual crystal. In contrast to that assumption, the present work suggests that there is an increased probability of molecular surface disorder in the vicinity of a grain boundary. The conclusion is based on the first detailed visualization of the formation of an ice grain boundary. The visualization is enabled by studying ice crystals growing into contact, at temperatures between -20°C and -15°C and pressures of 1-2 Torr, using Environmental Scanning Electron Microscopy. It is observed that the formation of a grain boundary induces a surface transition on the facets in contact. The transition does not propagate across facet edges. The surface transition is interpreted as the spreading of crystal dislocations away from the grain boundary. The observation constitutes a qualitatively new finding, and can potentially increase the understanding of specific processes in nature where ice grain boundaries are involved.

  14. Superconductivity of individual grains and inter-grain boundaries for polycrystalline FeSr2YCu2O6+y

    International Nuclear Information System (INIS)

    Yamaguchi, K.; Hata, Y.; Mochiku, T.; Yasuoka, H.

    2013-01-01

    Polycrystalline FeSr 2 YCu 2 O 6+y was synthesized and its transport and magnetic properties were studied. Diamagnetism was observed below 60 K. Zero resistivity was observed below 38 K under zero magnetic field and below 10 K under 160 kOe. A two-step transition was observed in resistivity measurement due to the superconductivity in individual grains and across inter-grain boundaries. The critical current density in individual grains, J c intra , at 2 K under 1 kOe was deduced 3.4 × 10 5 A/cm 2 from the Bean model. In contrast, the critical current density in inter-grain boundaries, J c inter , at 2 K was 1.7 A/cm 2 in voltage–current measurement. The two-step transition seems to result from the large difference between J c intra and J c inter

  15. Development of Niobium Boron grain retainer for aluminium silicon alloys

    OpenAIRE

    Nowak, Magdalena

    2011-01-01

    This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University Aluminium castings with a large grain structure have poor mechanical properties which are primarily due to casting defects as opposed to fine grain structure. The grain refinement practice using chemical addition is well established for wrought alloys, however in the case of casting alloys, the practice of adding grain refiners and the impact on castability is not well established. The additio...

  16. Imaging the Structure of Grains, Grain Boundaries, and Stacking Sequences in Single and Multi-Layer Graphene

    Science.gov (United States)

    Muller, David

    2012-02-01

    Graphene can be produced by chemical vapor deposition (CVD) on copper substrates on up to meter scales [1, 2], making their polycrystallinity [3,4] almost unavoidable. By combining aberration-corrected scanning transmission electron microscopy and dark-field transmission electron microscopy, we image graphene grains and grain boundaries across six orders of magnitude. Atomic-resolution images of graphene grain boundaries reveal that different grains can stitch together via pentagon-heptagon pairs. We use diffraction-filtered electron imaging to map the shape and orientation of several hundred grains and boundaries over fields of view of a hundred microns. Single, double and multilayer graphene can be differentiated, and the stacking sequence and relative abundance of sequences can be directly imaged. These images reveal an intricate patchwork of grains with structural details depending strongly on growth conditions. The imaging techniques enabled studies of the structure, properties, and control of graphene grains and grain boundaries [5]. [4pt] [1] X. Li et al., Science 324, 1312 (2009).[0pt] [2] S. Bae et al., Nature Nanotechnol. 5, 574 (2010).[0pt] [3] J. M. Wofford, et al., Nano Lett., (2010).[0pt] [4] P. Y. Huang, et al., Nature 469, 389--392 (2011); arXiv:1009.4714, (2010)[0pt] [5] In collaboration with Pinshane Y. Huang, C. S. Ruiz-Vargas, A. M. van der Zande, A. W. Tsen, L. Brown, R. Hovden, F. Ghahari, W. S. Whitney, M.P. Levendorf, J. W. Kevek, S. Garg, J. S. Alden, C. J. Hustedt, Y. Zhu, N. Petrone, J. Hone, J. Park, P. L. McEuen

  17. Thermally activated phase slippage in high-Tc grain-boundary Josephson junctions

    International Nuclear Information System (INIS)

    Gross, R.; Chaudhari, P.; Dimos, D.; Gupta, A.; Koren, G.

    1990-01-01

    The effect of thermally activated phase slippage (TAPS) in YBa 2 Cu 3 O 7 grain-boundary Josephson junctions has been studied. TAPS has been found to be responsible for the dc noise voltage superimposed on the dc Josephson current near the transition temperature. Because of the reduced Josephson coupling energy of the grain-boundary junctions, which is caused by a reduced superconducting order parameter at the grain-boundary interface, TAPS is present over a considerable temperature range. The implications of TAPS on the applicability of high-T c Josephson junctions are outlined

  18. Thermally activated phase slippage in high- T sub c grain-boundary Josephson junctions

    Energy Technology Data Exchange (ETDEWEB)

    Gross, R.; Chaudhari, P.; Dimos, D.; Gupta, A.; Koren, G. (IBM Thomas J. Watson Research Center, P.O. Box 218, Yorktown Heights, New York 10598 (USA))

    1990-01-08

    The effect of thermally activated phase slippage (TAPS) in YBa{sub 2}Cu{sub 3}O{sub 7} grain-boundary Josephson junctions has been studied. TAPS has been found to be responsible for the dc noise voltage superimposed on the dc Josephson current near the transition temperature. Because of the reduced Josephson coupling energy of the grain-boundary junctions, which is caused by a reduced superconducting order parameter at the grain-boundary interface, TAPS is present over a considerable temperature range. The implications of TAPS on the applicability of high-{ital T}{sub {ital c}} Josephson junctions are outlined.

  19. Molecular dynamics study of grain boundary diffusion of hydrogen in tungsten

    International Nuclear Information System (INIS)

    Von Toussaint, U; Gori, S; Manhard, A; Höschen, T; Höschen, C

    2011-01-01

    Understanding the influence of the microstructure of tungsten on hydrogen transport is crucial for the use of tungsten as first-wall material in fusion reactors. Here, we report the results of molecular dynamics and transition state studies on the influence of grain boundaries in tungsten on the transport of hydrogen. An exhaustive mapping of possible minimum activation energy migration trajectories for hydrogen as the trace impurity reveals a strongly modified activation energy distribution in the neighborhood of grain boundaries together with an altered connectivity matrix. The results indicate that grain boundaries in polycrystalline tungsten may provide an important transport channel, especially for neutron-damaged tungsten.

  20. Interaction of slip with grain boundary in the Li2 ordered structure - A Σ = 9 tilt boundary

    International Nuclear Information System (INIS)

    Yoo, M.H.; King, A.H.

    1988-01-01

    The role of slip/grain boundary interaction in intergranular fracture has been analyzed for a Σ = 9 tilt boundary in Li 2 ordered alloys by use of the anisotropic elasticity theory of dislocations and fracture. Screw superpartials cross slip easily at the boundary onto the (1 bar 11) and the (001) planes for low and high temperatures, respectively. Transmission of primary slip dislocations onto the conjugate slip system occurs with some difficulty, which is eased by localized disordering. Unless a symmetric double pile-up occurs simultaneously, cleavage fracture is predicted to occur on the (bar 1 11) plane, not intergranular fracture. Absorption (or emission ) of superpartials occurs only when the boundary region is disordered. The inherent weakness of grain boundaries in Ni 3 Al and its improvement by boron segregation are discussed

  1. Influence of cold rolling direction on texture, inhibitor and magnetic properties in strip-cast grain-oriented 3% silicon steel

    Energy Technology Data Exchange (ETDEWEB)

    Fang, F., E-mail: fangfengdbdx@163.com [State Key Laboratory of Rolling Technology and Automation, Northeastern University, Shenyang 110819 (China); Lu, X.; Zhang, Y.X.; Wang, Y.; Jiao, H.T.; Cao, G.M.; Yuan, G.; Xu, Y.B. [State Key Laboratory of Rolling Technology and Automation, Northeastern University, Shenyang 110819 (China); Misra, R.D.K. [Laboratory for Excellence in Advanced Steel Research, Department of Metallurgical, Materials and Biomedical Engineering, University of Texas at El Paso, EL Paso, TX 79968 (United States); Wang, G.D. [State Key Laboratory of Rolling Technology and Automation, Northeastern University, Shenyang 110819 (China)

    2017-02-15

    An unconventional cold rolling scheme (inclined rolling at 0°, 30°, 45°, 90° during second-stage cold rolling process) was adopted to process grain-oriented silicon steel based on strip casting process. The influences of inclination angles on microstructure, texture, inhibitor and magnetic properties were studied by a combination of EBSD, XRD and TEM. It was found that the α-fiber texture was weakened and γ-fiber was strengthened in cold rolled sheet with increase in inclination angle. The primary recrystallization sheet exhibited more homogeneous microstructure with relatively strong γ-fiber, medium α-fiber texture, weak λ-fiber texture and Goss component at high inclination angles. Fine and homogeneous inhibitors were obtained after primary annealing with increase in inclination angle from 0° to 90° because of more uniform deformation after inclined rolling. The grain-oriented silicon steel experienced completely secondary recrystallization at various inclination angles after final annealing process, with superior magnetic properties at 0° and 90°. Furthermore, Goss nuclei capable of final secondary recrystallization in strip casting process newly formed both in-grain shear bands and grain boundaries region during second-stage cold rolling and subsequent annealing process, which is different from the well-accepted results that Goss texture originated from the subsurface layer of the hot rolled sheet or during intermediate annealing process. In addition, the Goss texture that nucleated in-grain shear bands was weaker but more accurate as compared to that in grain boundaries region. - Highlights: • Inclined cold rolling was adopted to process strip-cast grain-oriented silicon steel. • Influence of inclination angles on texture, inhibitor and magnetic properties was studied. • The initial texture was changed with respect to the inclination angle. • Homogeneous inhibitors were obtained after primary annealing at various inclination angles.

  2. Summary of structural refinement in hi-silicon aluminium piston alloy with phosphorous as grain refiner

    International Nuclear Information System (INIS)

    Malik, F.A.; Sheikh, S.T.; Choudhry, A.A.

    2003-01-01

    Aluminium Silicon Alloys are extensively used in a wide variety of applications. There are numerous variables in composition, production control, final structure which can influence the mechanical properties of Hi - Silicon Piston alloys. Hypereutectic AlSi alloys develop coarse grain primary silicon crystals, which have a strong negative effect on the tensile strength, the ductility, and the hardness. These crystals slow machining and reduce the tool life considerably. Phosphorous addition produce a fine, evenly spread crystal structure, lamellar structure of the silicon changes into a granular structure. (author)

  3. Grain Boundary Conformed Volumetric Mesh Generation from a Three-Dimensional Voxellated Polycrystalline Microstructure

    Science.gov (United States)

    Lee, Myeong-Jin; Jeon, Young-Ju; Son, Ga-Eun; Sung, Sihwa; Kim, Ju-Young; Han, Heung Nam; Cho, Soo Gyeong; Jung, Sang-Hyun; Lee, Sukbin

    2018-03-01

    We present a new comprehensive scheme for generating grain boundary conformed, volumetric mesh elements from a three-dimensional voxellated polycrystalline microstructure. From the voxellated image of a polycrystalline microstructure obtained from the Monte Carlo Potts model in the context of isotropic normal grain growth simulation, its grain boundary network is approximated as a curvature-maintained conformal triangular surface mesh using a set of in-house codes. In order to improve the surface mesh quality and to adjust mesh resolution, various re-meshing techniques in a commercial software are applied to the approximated grain boundary mesh. It is found that the aspect ratio, the minimum angle and the Jacobian value of the re-meshed surface triangular mesh are successfully improved. Using such an enhanced surface mesh, conformal volumetric tetrahedral elements of the polycrystalline microstructure are created using a commercial software, again. The resultant mesh seamlessly retains the short- and long-range curvature of grain boundaries and junctions as well as the realistic morphology of the grains inside the polycrystal. It is noted that the proposed scheme is the first to successfully generate three-dimensional mesh elements for polycrystals with high enough quality to be used for the microstructure-based finite element analysis, while the realistic characteristics of grain boundaries and grains are maintained from the corresponding voxellated microstructure image.

  4. The Effect of High Temperature Annealing on the Grain Characteristics of a Thin Chemical Vapor Deposition Silicon Carbide Layer.

    Energy Technology Data Exchange (ETDEWEB)

    Isabella J van Rooyen; Philippus M van Rooyen; Mary Lou Dunzik-Gougar

    2013-08-01

    The unique combination of thermo-mechanical and physiochemical properties of silicon carbide (SiC) provides interest and opportunity for its use in nuclear applications. One of the applications of SiC is as a very thin layer in the TRi-ISOtropic (TRISO) coated fuel particles for high temperature gas reactors (HTGRs). This SiC layer, produced by chemical vapor deposition (CVD), is designed to withstand the pressures of fission and transmutation product gases in a high temperature, radiation environment. Various researchers have demonstrated that macroscopic properties can be affected by changes in the distribution of grain boundary plane orientations and misorientations [1 - 3]. Additionally, various researchers have attributed the release behavior of Ag through the SiC layer as a grain boundary diffusion phenomenon [4 - 6]; further highlighting the importance of understanding the actual grain characteristics of the SiC layer. Both historic HTGR fission product release studies and recent experiments at Idaho National Laboratory (INL) [7] have shown that the release of Ag-110m is strongly temperature dependent. Although the maximum normal operating fuel temperature of a HTGR design is in the range of 1000-1250°C, the temperature may reach 1600°C under postulated accident conditions. The aim of this specific study is therefore to determine the magnitude of temperature dependence on SiC grain characteristics, expanding upon initial studies by Van Rooyen et al, [8; 9].

  5. Study of grain boundary tunneling in barium-titanate ceramic films

    CERN Document Server

    Wong, H; Poon, M C

    1999-01-01

    The temperature and the electric-field dependences of the current-voltage characteristics and the low-frequency noise of barium-titanate ceramic films are studied. An abnormal field dependence is observed in the resistivity of BaTiO sub 3 materials with a small average grain size. In addition, experiments show that the low-frequency noise behaviors are governed by grain-boundary tunneling at room temperature and by trapping-detrapping of grain-boundary states at temperatures above the Curie point. Physical models for the new observations are developed. Results suggest that grain-boundary tunneling of carriers is as important as the double Schottky barrier in the current conduction in BaTiO sub 3 materials with small grain sizes.

  6. Temperature distribution in graphene doped with nitrogen and graphene with grain boundary.

    Science.gov (United States)

    Lotfi, Erfan; Neek-Amal, M

    2017-06-01

    Graphene doped with nitrogen exhibits unique properties different than perfect graphene. The temperature distribution in nitrogen-doped graphene (N-graphene) and in the graphene with grain boundary is investigated using molecular dynamics simulations. The temperature distribution in nitrogen-doped graphene nanoribbon, containing two types of grain boundaries, was found to be sensitive to the number of dopants and grain boundary. We also found that there is a remarkable temperature gap in the temperature profile of N-graphene nanoribbon-containing a grain boundary. For any doping ratio N/C we found that the nitrogen atoms enhance roughness of N-graphene and decrease thermal conductivity. Copyright © 2017 Elsevier Inc. All rights reserved.

  7. Grain Boundary Engineering the Mechanical Properties of Allvac 718Plus(Trademark) Superalloy

    Science.gov (United States)

    Gabb, Timothy P.; Telesman, Jack; Garg, Anita; Lin, Peter; Provenzano, virgil; Heard, Robert; Miller, Herbert M.

    2010-01-01

    Grain Boundary Engineering can enhance the population of structurally-ordered "low S" Coincidence Site Lattice (CSL) grain boundaries in the microstructure. In some alloys, these "special" grain boundaries have been reported to improve overall resistance to corrosion, oxidation, and creep resistance. Such improvements could be quite beneficial for superalloys, especially in conditions which encourage damage and cracking at grain boundaries. Therefore, the effects of GBE processing on high-temperature mechanical properties of the cast and wrought superalloy Allvac 718Plus (Allvac ATI) were screened. Bar sections were subjected to varied GBE processing, and then consistently heat treated, machined, and tested at 650 C. Creep, tensile stress relaxation, and dwell fatigue crack growth tests were performed. The influences of GBE processing on microstructure, mechanical properties, and associated failure modes are discussed.

  8. Microstructure of Josephson junctions: Effect on supercurrent transport in YBCO grain boundary and barrier layer junctions

    International Nuclear Information System (INIS)

    Merkle, K.L.; Huang, Y.

    1998-01-01

    The electric transport of high-temperature superconductors, such as YBa 2 Cu 3 O 7-x (YBCO), can be strongly restricted by the presence of high-angle grain boundaries (GB). This weak-link behavior is governed by the macroscopic GB geometry and the microscopic grain boundary structure and composition at the atomic level. Whereas grain boundaries present a considerable impediment to high current applications of high T c materials, there is considerable commercial interest in exploiting the weak-link-nature of grain boundaries for the design of microelectronic devices, such as superconducting quantum interference devices (SQUIDs). The Josephson junctions which form the basis of this technology can also be formed by introducing artificial barriers into the superconductor. The authors have examined both types of Josephson junctions by EM techniques in an effort to understand the connection between microstructure/chemistry and electrical transport properties. This knowledge is a valuable resource for the design and production of improved devices

  9. The effect of surface contact conditions on grain boundary interdiffusion in a semi-infinite bicrystal

    Czech Academy of Sciences Publication Activity Database

    Svoboda, Jiří; Fischer, F. D.; Klinger, L.; Rabkin, E.

    2014-01-01

    Roč. 94, č. 30 (2014), s. 3398-3412 ISSN 1478-6435 Institutional support: RVO:68081723 Keywords : grain boundary diffusion * liquid metals * stress analysis * interfacial thermodynamics Subject RIV: BJ - Thermodynamics Impact factor: 1.825, year: 2014

  10. Critical current of a high Tc Josephson grain boundary junction in high magnetic field

    Science.gov (United States)

    Däumling, M.; Sarnelli, E.; Chaudhari, P.; Gupta, A.; Lacey, J.

    1992-09-01

    The critical current (Ic) of YBa2Cu3O7-δ grain boundary Josephson junctions was measured up to magnetic fields of 5 T. Magnetic field history dependent Ic values were observed even after correction for self-field effects stemming from hysteretic shielding currents in the grain adjacent to the boundary. A novel feature observed is an anomalous increase in Ic in high magnetic fields of several Telsa.

  11. Fractional Josephson vortices at YBa$_2$Cu$_3$O$_{7-x}$ grain boundaries

    OpenAIRE

    Mints, R. G.; Papiashvili, Ilya

    2001-01-01

    We report numerical simulations of magnetic flux patterns in asymmetric 45$^{\\circ}$ [001]-tilt grain boundaries in YBa$_2$Cu$_3$O$_{7-x}$ superconducting films. The grain boundaries are treated as Josephson junctions with the critical current density $j_c(x)$ alternating along the junctions. We demonstrate the existence of Josephson vortices with fractional flux quanta for both periodic and random $j_c(x)$. A method is proposed to extract fractional vortices from experimental flux patterns.

  12. The vibrational spectrum of the atoms in the grain boundaries of nanocrystalline Pd

    Energy Technology Data Exchange (ETDEWEB)

    Stuhr, U. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Wipf, H.; Hahn, H. [Technische Hochschule Darmstadt (Germany); Natter, H.; Hemperlmann, R. [Universitaet des Saarlandes, Saarbruecken (Germany); Andersen, K. [Institut Max von Laue - Paul Langevin (ILL), 38 - Grenoble (France)

    1997-09-01

    The vibrational excitations of the atoms in nanocrystalline Pd was investigated by neutron-time-of-flight spectroscopy. Hydrogen was used as a probe for the vibrations in the grain boundaries. The separation between the H and Pd vibrations was done by spin analysis. The results show that in the grain boundary the density of states of low energy excitations ({<=}5 meV) is drastically increased. (author) 3 figs., 3 refs.

  13. Backscattered electron technique used for studying the grain boundary structure in polycrystals

    International Nuclear Information System (INIS)

    Lopes, Luiz Carlos Rolim; Thomson, Chris Boyd; Randle, Valerie

    1996-01-01

    In this work the electron backscatter diffraction technique has been used to study the grain boundary character distribution in a austenitic steel and a ordered intermetallic Fe Al. For the first material it has been found that the hot rolling and solubilization process produce grain boundary character distribution with 1/4 of Σ = 3 interface. For the intermetallic Fe Al it was found that Σ = 1 and Σ = 5 interfaces to do not show tendency to show intergranular cracking. (author)

  14. Influence of microstructure on grain boundary sliding of alloys 600 and 690

    International Nuclear Information System (INIS)

    Kergaravat, J.F.; Guetaz, L.; Baillin, X.; Robert, G.

    1995-01-01

    The influence of deformation and damage mechanisms, and more especially of the grain boundary sliding effect, on the stress corrosion of nickel base alloys used in nuclear industry (exchanger tubes), has been experimentally examined. The grain boundary sliding effect has been measured at 500 C and 320 C on several samples of alloy 690 and 600 (in the mill annealed and mill annealed heat treated conditions). (author). 4 figs., 1 tab

  15. Retardation of grain boundary self-diffusion in nickel doped with antimony and tin

    International Nuclear Information System (INIS)

    Padgett, R.A.; White, C.L.

    1984-01-01

    Many important metallurgical phenomena are strongly influenced or controlled by grain boundary mass transport. There is also much evidence that the composition of grain boundaries is often significantly different from the overall composition of metals and alloys, owing to strong segregation of residual (and often undetected) impurities. This segregation, which does not always advertise its presence through grain boundary brittleness, may vary markedly from heat to heat, and occasionally from specimen to specimen within a given heat. Unfortunately, there are relatively few experimental observations of how such segregation affects grain boundary mass transport, and even less fundamental understanding of how these effects occur. In this paper we present autoradiographic results on self-diffusion of 63 Ni in nickel and nickel doped with antimony and tin. While these results do not permit a quantitative evaluation of the grain boundary diffusivity, D, they qualitatively illustrate the dramatic effect that these solute elements have on the ability of nickel grain boundaries to act as preferential paths for mass transport

  16. On the small angle twist sub-grain boundaries in Ti3AlC2

    Science.gov (United States)

    Zhang, Hui; Zhang, Chao; Hu, Tao; Zhan, Xun; Wang, Xiaohui; Zhou, Yanchun

    2016-04-01

    Tilt-dominated grain boundaries have been investigated in depth in the deformation of MAX phases. In stark contrast, another important type of grain boundaries, twist grain boundaries, have long been overlooked. Here, we report on the observation of small angle twist sub-grain boundaries in a typical MAX phase Ti3AlC2 compressed at 1200 °C, which comprise hexagonal screw dislocation networks formed by basal dislocation reactions. By first-principles investigations on atomic-scale deformation and general stacking fault energy landscapes, it is unequivocally demonstrated that the twist sub-grain boundaries are most likely located between Al and Ti4f (Ti located at the 4f Wyckoff sites of P63/mmc) layers, with breaking of the weakly bonded Al-Ti4f. The twist angle increases with the increase of deformation and is estimated to be around 0.5° for a deformation of 26%. This work may shed light on sub-grain boundaries of MAX phases, and provide fundamental information for future atomic-scale simulations.

  17. Imaging of magnetic flux states in YBa2Cu3O7-δ grain boundary junctions

    International Nuclear Information System (INIS)

    Mayer, B.; Shen, Y.; Vase, P.

    1993-01-01

    The weak link behavior of grain boundaries in the high temperature superconductors has been studied intensively during the last years. On the one hand the weak link nature of the grain boundaries is responsible for the disappointingly low critical current densities in polycrystalline materials. However, on the other hand it offers the possibility to fabricate Josephson elements required for microelectronic applications of the cuprate superconductors. Although various types of artificially generated, so-called engineered grain boundary Josephson junctions (GBJs) have been fabricated and characterized with respect to their structural and electrical properties there are still open questions concerning the weak link nature of high-T c GBJs. As a consequence of the weak link nature the supercurrent density of the GBJs should be spatially modulated, if magnetic flux is coupled into the grain boundary by a magnetic field applied parallel to the grain boundary plane. We report on direct measurements of the spatially modulated supercurrent density in YBa 2 Cu 3 O 7-δ bicrystal GBJs using Low Temperature Scanning Electron Microscopy (LTSEM). The LTSEM images directly show the spatial oscillation of the supercurrent density J s along the grain boundary with a resolution of about 1 μm. Varying the applied magnetic field different magnetic flux states containing up to 10 Josephson vortices could be observed. (orig.)

  18. Grain size and boundary-related effects on the properties of nanocrystalline barium titanate ceramics

    Czech Academy of Sciences Publication Activity Database

    Buscaglia, V.; Buscaglia, M. T.; Viviani, M.; Mitoseriu, L.; Nanni, P.; Trefiletti, V.; Piaggio, P.; Gregora, Ivan; Ostapchuk, Tetyana; Pokorný, Jan; Petzelt, Jan

    2006-01-01

    Roč. 26, - (2006), s. 2889-2898 ISSN 0955-2219 R&D Projects: GA MŠk OC 525.20 Institutional research plan: CEZ:AV0Z10100520 Keywords : grain size * grain boundaries * spectroscopy * dielectric properties * BaTiO 3 Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.576, year: 2006

  19. Superplasticity and grain boundary character distribution in overaged Al-Li-Cu-Mg-Zr alloy

    International Nuclear Information System (INIS)

    Avramovic-Cingara, G.; Aust, K.T.; Perovic, D.D.; McQueen, H.J.

    1995-01-01

    Samples of 8091 alloy were subjected to a thermomechanical processing (TMP) treatment that included the following stages: overaging before deformation, multistage deformation at 300 deg C and strain rate change tests for superplasticity. Torsional deformation was utilized both to develop the refined microstructure and to test for superplasticity. The strain rate sensitivity, m, of the material ranged between 0.30 and 0.45 at 450 deg C for strain rates between 8 x 10 -2 and 10 -3 s -1 . The grain boundary character distribution (GBCD) of thermomechanically processed Al-Li-Cu-Mg-Zr (8091) alloy, which develops good superplastic response, has been determined by an electron backscattering diffraction technique (EBSD). All grain boundaries have been classified into one of three categories in terms of Σ values : low angle, coincidence site lattice and random high angle boundaries. Quantitative studies of grain boundary character were done after various processing stages to obtain evidence about structure evolution and indicate an increase in Σ boundary frequency following TMP. Selected area electron diffraction examination (SAD) gave evidence about the refined structure, in which the grain boundary misorientation increased EBSD how the grain boundary character was changed to high Σ values. TEM analyses indicate that the T 2 phase is responsible for substructure stabilization. There is no evidence of cavity formation during superplastic deformation by torsion, which suggests that cavity nucleation is strongly influenced by the nature of stress. (author). 32 refs., 3 tabs., 9 figs

  20. Relationship between lattice mismatch and ionic conduction of grain boundary in YSZ

    Directory of Open Access Journals (Sweden)

    Fei Ye

    2014-02-01

    Full Text Available The grain boundary plays an important role in the electrical behaviors of solid oxide electrolytes for solid state fuel cells. To reveal the relationship between the structure and the ionic conductivity of grain boundary, the conductive properties of {1 1 1} and {1 1 0} twist grain boundaries in 8 mol% yttria-stabilized zirconia have been examined. These boundaries have a series of Σ values defined by the coincident site lattice model. It has been found that the activation energy of {1 1 1} twist grain boundary increases and then decreases with the Σ value, while that of the {1 1 0} boundary shows an opposite trend. It is suggested that the properties can reflect the balance of the effects of lattice mismatch on the diffusion ability of oxygen vacancies and the segregation of oxygen vacancies and Y3+ ions. Therefore, the properties in polycrystalline electrolyte can be adjusted by controlling the grain boundary structures.

  1. Superplastic Constitutive Equation Including Percentage of High-Angle Grain Boundaries as a Microstructural Parameter

    Science.gov (United States)

    Wang, K.; Liu, F. C.; Xue, P.; Wang, D.; Xiao, B. L.; Ma, Z. Y.

    2016-01-01

    Fifteen Al-Mg-Sc samples with subgrain/grain sizes in the range of 1.8 to 4.9 μm were prepared through the processing methods of friction stir processing (FSP), equal-channel-angular pressing (ECAP), rolling, annealing, and combinations of the above. The percentages of high-angle grain boundaries (HAGBs) of these fine-grained alloys were distributed from 39 to 97 pct. The samples processed through FSP had a higher percentage of HAGBs compared to other samples. Superplasticity was achieved in all fifteen samples, but the FSP samples exhibited better superplasticity than other samples because their fine equiaxed grains, which were mostly surrounded by HAGBs, were conducive to the occurrence of grain boundary sliding (GBS) during superplastic deformation. The dominant deformation mechanism was the same for all fifteen samples, i.e., GBS controlled by grain boundary diffusion. However, the subgrains were the GBS units for the rolled or ECAP samples, which contained high percentages of unrecrystallized grains, whereas the fine grains were the GBS units for the FSP samples. Superplastic data analysis revealed that the dimensionless A in the classical constitutive equation for superplasticity of fine-grained Al alloys was not a constant, but increased with an increase in the percentage of HAGBs, demonstrating that the enhanced superplastic deformation kinetics can be ascribed to the high percentage of HAGBs. A modified superplastic constitutive equation with the percentage of HAGBs as a new microstructural parameter was established.

  2. Crystalline orientation dependent photoresponse and heterogeneous behaviors of grain boundaries in perovskite solar cells

    Science.gov (United States)

    Jiang, Chuanpeng; Zhang, Pengpeng

    2018-02-01

    Using photoconductive atomic force microscopy and Kelvin probe force microscopy, we characterize the local electrical properties of grains and grain boundaries of organic-inorganic hybrid perovskite (CH3NH3PbI3) thin films on top of a poly(3,4-ethylenedioxythiophene)-polystyrene sulfonate (PEDOT:PSS)/ITO substrate. Three discrete photoconductivity levels are identified among perovskite grains, likely corresponding to the crystal orientation of each grain. Local J-V curves recorded on these grains further suggest an anti-correlation behavior between the short circuit current (JSC) and open circuit voltage (VOC). This phenomenon can be attributed to diffusion-limited surface recombination at the non-selective perovskite-tip contact, where a higher carrier mobility established in the perovskite grain results in an enhanced surface recombination and thus a lower VOC. In addition, the photoresponse of perovskite films displays a pronounced heterogeneity across the grain boundaries, with the boundaries formed between grains of the same photoconductivity level displaying even enhanced photocurrent and open circuit voltage compared to those of the adjacent grain interiors. These observations highlight the significance of controlling the microstructure of perovskite thin films, which will be a necessary route for further improving the efficiency of perovskite solar cells.

  3. Improvement in tribological properties by modification of grain boundary and microstructure of ultrananocrystalline diamond films.

    Science.gov (United States)

    Sankaran, Kamatchi Jothiramalingam; Kumar, Niranjan; Kurian, Joji; Ramadoss, Radhika; Chen, Huang-Chin; Dash, Sitaram; Tyagi, Ashok Kumar; Lee, Chi-Young; Tai, Nyan-Hwa; Lin, I-Nan

    2013-05-01

    Grain boundaries and microstructures of ultrananocrystalline diamond (UNCD) films are engineered at nanoscale by controlling the substrate temperature (TS) and/or by introducing H2 in the commonly used Ar/CH4 deposition plasma in a microwave plasma enhanced chemical vapor deposition system. A model for the grain growth is proposed. The films deposited at low TS consist of random/spherical shaped UNCD grains with well-defined grain boundaries. On increasing TS, the adhering efficiency of CH radical onto diamond lattice drops and trans-polyacetylene (t-PA) encapsulating the nanosize diamond clusters break due to hydrogen abstraction activated, rendering the diamond phase less passivated. This leads to the C2 radical further attaching to the diamond lattice, resulting in the modification of grain boundaries and promoting larger sized clustered grains with a complicated defect structure. Introduction of H2 in the plasma at low TS gives rise to elongated clustered grains that is attributed to the presence of atomic hydrogen in the plasma, preferentially etching out the t-PA attached to nanosized diamond clusters. On the basis of this model a technologically important functional property, namely tribology of UNCD films, is studied. A low friction of 0.015 is measured for the film when ultranano grains are formed, which consist of large fractions of grain boundary components of sp(2)/a-C and t-PA phases. The grain boundary component consists of large amounts of hydroxylic and carboxylic functional groups which passivates the covalent carbon dangling bonds, hence low friction coefficient. The improved tribological properties of films can make it a promising candidate for various applications, mainly in micro/nanoelectro mechanical system (M/NEMS), where low friction is required for high efficiency operation of devices.

  4. Detection of grain-boundary resistance to slip transfer using nanoindentation

    NARCIS (Netherlands)

    Soer, WA; De Hosson, JTM

    2005-01-01

    Nanoindentation measurements near a high-angle grain boundary in a Fe-14%Si bicrystal showed dislocation pile-up and transmission across the boundary. The latter is observed as a characteristic displacement jump, from which the Hall-Petch slope can be calculated as a measure for the slip

  5. Precession electron diffraction for SiC grain boundary characterization in unirradiated TRISO fuel

    International Nuclear Information System (INIS)

    Lillo, T.M.; Rooyen, I.J. van; Wu, Y.Q.

    2016-01-01

    Highlights: • SiC grain orientation determined by TEM-based precession electron diffraction. • Orientation data improved with increasing TEM sample thickness. • Fraction of low angle grain boundaries lower from PED data than EBSD data. • Fractions of high angle and CSL-related boundaries similar to EBSD data. - Abstract: Precession electron diffraction (PED), a transmission electron microscopy-based technique, has been evaluated for the suitability for evaluating grain boundary character in the SiC layer of tristructural isotropic (TRISO) fuel. This work reports the effect of transmission electron microscope (TEM) lamella thickness on the quality of data and establishes a baseline comparison to SiC grain boundary characteristics, in an unirradiated TRISO particle, determined previously using a conventional electron backscatter diffraction (EBSD) scanning electron microscope (SEM)-based technique. In general, it was determined that the lamella thickness produced using the standard focused ion beam (FIB) fabrication process (∼80 nm), is sufficient to provide reliable PED measurements, although thicker lamellae (∼120 nm) were found to produce higher quality orientation data. Also, analysis of SiC grain boundary character from the TEM-based PED data showed a much lower fraction of low-angle grain boundaries compared to SEM-based EBSD data from the SiC layer of a TRISO-coated particle made using the same fabrication parameters and a SiC layer deposited at a slightly lower temperature from a surrogate TRISO particle. However, the fractions of high-angle and coincident site lattice (CSL)-related grain boundaries determined by PED are similar to those found using SEM-based EBSD. Since the grain size of the SiC layer of TRSIO fuel can be as small as 250 nm (Kirchhofer et al., 2013), depending on the fabrication parameters, and since grain boundary fission product precipitates in irradiated TRISO fuel can be nano-sized, the TEM-based PED orientation data

  6. Large-grain polycrystalline silicon film by sequential lateral solidification on a plastic substrate

    International Nuclear Information System (INIS)

    Kim, Yong-Hae; Chung, Choong-Heui; Yun, Sun Jin; Moon, Jaehyun; Park, Dong-Jin; Kim, Dae-Won; Lim, Jung Wook; Song, Yoon-Ho; Lee, Jin Ho

    2005-01-01

    A large-grain polycrystalline silicon film was obtained on a plastic substrate by sequential lateral solidification. With various combinations of sputtering powers and Ar working gas pressures, the conditions for producing dense amorphous silicon (a-Si) and SiO 2 films were optimized. The successful crystallization of the a-Si film is attributed to the production of a dense a-Si film that has low argon content and can endure high-intensity laser irradiation

  7. The Pinning by Particles of Low and High Angle Grain Boundaries during Grain Growth

    DEFF Research Database (Denmark)

    Tweed, C.J.; Ralph, B.; Hansen, Niels

    1984-01-01

    and coworkers. These estimates of local driving pressures have shown that they are similar for both the low and the high angle boundaries encountered in the samples. The pinning effects by particles at high angle boundaries are in general accord with the model due to Zener whilst those at low angle boundaries...

  8. Seeded Grain Growth for Textured Silicon Carbide and Mullite

    National Research Council Canada - National Science Library

    Sacks, Michael

    1998-01-01

    .... The volume fraction, size, and morphology of the in-situ grown plate-like grains could be controlled through variables such as heat-treatment temperature, matrix particle size, seed concentration, additive type, etc...

  9. Modeling of MnS precipitation during the crystallization of grain oriented silicon steel

    OpenAIRE

    Kalisz, D.; Żak, P. L.; Lelito, J.; Szucki, M.; Suchy, J. S.; Gracz, B.

    2015-01-01

    The process of manganese sulfide formation in the course of grain-oriented silicon steel solidification process is described in the paper. Fine dispersive MnS inclusions are grain growth inhibitors and apart from AlN inclusions they contribute to the formation of a privileged texture, i.e. Goss texture. A computer simulation of a high-silicon steel ingot solidification with the use of author’s software has been performed. Ueshima model was adapted for simulating the 3 % Si steel ingot solidif...

  10. Conductive Nature of Grain Boundaries in Nanocrystalline Stabilized Bi2O3Thin-Film Electrolyte.

    Science.gov (United States)

    Jeong, Seung Jin; Kwak, No Woo; Byeon, Pilgyu; Chung, Sung-Yoon; Jung, WooChul

    2018-02-21

    Stabilized Bi 2 O 3 has gained a considerable amount of attention as a solid electrolyte material for low-temperature solid oxide fuel cells due to its superior oxygen-ion conductivity at the temperature of relevance (≤500 °C). Despite many research efforts to measure the transport properties of stabilized Bi 2 O 3 , the effects of grain boundaries on the electrical conductivity have rarely been reported and their results are even controversial. Here, we attempt quantitatively to assess the grain boundary contribution out of the total ionic conductivity at elevated temperatures (350-500 °C) by fabricating epitaxial and nano-polycrystalline thin films of yttrium-stabilized Bi 2 O 3 . Surprisingly, both epitaxial and polycrystalline films show nearly identical levels of ionic conductivity, as measured by alternating current impedance spectroscopy and this is the case despite the fact that the polyfilm possesses nanosized columnar grains and thus an extremely high density of the grain boundaries. The highly conductive nature of grain boundaries in stabilized Bi 2 O 3 is discussed in terms of the clean and chemically uniform grain boundary without segregates, and the implications for device application are suggested.

  11. Process for preparing fine grain silicon carbide powder

    Science.gov (United States)

    Wei, G.C.

    Finely divided silicon carbide powder is obtained by mixing colloidal silica and unreacted phenolic resin in either acetone or methanol, evaporating solvent from the obtained solution to form a gel, drying and calcining the gel to polymerize the phenolic resin therein, pyrolyzing the dried and calcined gel at a temperature in the range of 500 to 1000/sup 0/C, and reacting silicon and carbon in the pyrolyzed gel at a temperature in the range of 1550 to 1700/sup 0/C to form the powder.

  12. Segregation of sp-impurities at grain boundaries and surfaces: comparison of fcc cobalt and nickel

    Czech Academy of Sciences Publication Activity Database

    Všianská, Monika; Vémolová, H.; Šob, Mojmír

    2017-01-01

    Roč. 25, č. 8 (2017), č. článku 085004. ISSN 0965-0393 R&D Projects: GA ČR(CZ) GA16-24711S Institutional support: RVO:68081723 Keywords : local magnetic-moments * total-energy calculations * augmented-wave method * solute segregation * tilt boundaries * embrittling potency * alloying elements * hcp metals * basis-set * 1st-principles * grain boundary segregation * strengthening/embrittling energy * grain boundary magnetism * ab initio calculations * surface segregation Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 1.891, year: 2016

  13. Silicon nano grains with aluminum contacts studied by the Density Functional method

    International Nuclear Information System (INIS)

    Mazzone, A.M.; Summonte, C.

    2005-01-01

    The purpose of this study is the evaluation of the effects of metallic contacts on nanocrystalline silicon grains and is based on the use of the Density Functional theory. The structures considered are plated crystalline grains and the contacts are constructed by depositing an aluminum layer on the two opposite sides of the nano grain. The calculations indicate that, as for monolayer films deposited on bulk samples, the aluminum coating has a layered structure without clustering and with minimum intermixing with the silicon atoms. The built-in potential across the entire device has a functional dependence on the geometry of the nano grain and of the contacts. Potentially, this property is important for the fabrication of novel Schottky-barrier devices. However the strength of bonding is generally lower in the structures with contacts and this casts doubts on their stability

  14. Observing grain boundaries in CVD-grown monolayer transition metal dichalcogenides

    KAUST Repository

    Ly, Thuchue

    2014-11-25

    Two-dimensional monolayer transition metal dichalcogenides (TMdCs), driven by graphene science, revisit optical and electronic properties, which are markedly different from bulk characteristics. These properties are easily modified due to accessibility of all the atoms viable to ambient gases, and therefore, there is no guarantee that impurities and defects such as vacancies, grain boundaries, and wrinkles behave as those of ideal bulk. On the other hand, this could be advantageous in engineering such defects. Here, we report a method of observing grain boundary distribution of monolayer TMdCs by a selective oxidation. This was implemented by exposing directly the TMdC layer grown on sapphire without transfer to ultraviolet light irradiation under moisture-rich conditions. The generated oxygen and hydroxyl radicals selectively functionalized defective grain boundaries in TMdCs to provoke morphological changes at the boundary, where the grain boundary distribution was observed by atomic force microscopy and scanning electron microscopy. This paves the way toward the investigation of transport properties engineered by defects and grain boundaries. (Figure Presented).

  15. Grain Wall Boundaries in Centimeter-scale Continuous Monolayer WS2 Film Grown By Chemical Vapor Deposition.

    Science.gov (United States)

    Jia, Zhiyan; Hu, Wentao; Xiang, Jianyong; Wen, Fusheng; Nie, Anmin; Mu, Congpu; Zhao, Zhisheng; Xu, Bo; Tian, Yongjun; Liu, Zhongyuan

    2018-04-05

    Centimeter-scale continuous monolayer WS2 film with large tensile strain has been successfully grown on oxidized silicon substrate by chemical vapor deposition (CVD), in which monolayer grains can be more than 200 um in size. Monolayer WS2 grains are observed to merge together via not only traditional grain boundaries (GBs) but also non-traditional ones, which are named as grain walls (GWs) due to their nanometer-scale widths. The GWs are revealed to consist of two or three layers. Though not a monolayer, the GWs exhibit significantly enhanced fluorescence (FL) and photoluminescence (PL). This enhancement may be attributed to abundant structural defects such as stacking faults and partial dislocations in the GWs, which are clearly observable in atomically resolved HRTEM and STEM images. Moreover, GW-based phototransistor is found to deliver higher photocurrent than that based on monolayer film. These features of GWs provide a clue to microstructure engineering of monolayer WS2 for specific applications in (opto)electronics. © 2018 IOP Publishing Ltd.

  16. First-principles study of the effects of segregated Ga on an Al grain boundary

    International Nuclear Information System (INIS)

    Zhang Ying; Lu Guanghong; Wang Tianmin; Deng Shenghua; Shu Xiaolin; Kohyama, Masanori; Yamamoto, Ryoichi

    2006-01-01

    The effects of different amounts of segregated Ga (substitutional) on an Al grain boundary have been investigated by using a first-principles pseudopotential method. The segregated Ga is found to draw charge from the surrounding Al due to the electronegativity difference between Ga and Al, leading to a charge density reduction between Ga and Al as well as along the Al grain boundary. Such an effect can be enhanced by increasing the Ga segregation amount. With further Ga segregated, in addition to the charge-drawing effect that occurs in the Al-Ga interface, a heterogeneous α-Ga-like phase can form in the grain boundary, which greatly alters the boundary structure. These effects are suggested to be responsible for Ga-induced Al intergranular embrittlement

  17. Carrier Transport, Recombination, and the Effects of Grain Boundaries in Polycrystalline Cadmium Telluride Thin Films for Photovoltaics

    Science.gov (United States)

    Tuteja, Mohit

    Cadmium Telluride (CdTe), a chalcogenide semiconductor, is currently used as the absorber layer in one of the highest efficiency thin film solar cell technologies. Current efficiency records are over 22%. In 2011, CdTe solar cells accounted for 8% of all solar cells installed. This is because, in part, CdTe has a low degradation rate, high optical absorption coefficient, and high tolerance to intrinsic defects. Solar cells based on polycrystalline CdTe exhibit a higher short-circuit current, fill factor, and power conversion efficiency than their single crystal counterparts. This is despite the fact that polycrystalline CdTe devices exhibit lower open-circuit voltages. This is contrary to the observation for silicon and III-V semiconductors, where material defects cause a dramatic drop in device performance. For example, grain boundaries in covalently-bonded semiconductors (a) act as carrier recombination centers, and (b) lead to localized energy states, causing carrier trapping. Despite significant research to date, the mechanism responsible for the superior current collection properties of polycrystalline CdTe solar cells has not been conclusively answered. This dissertation focuses on the macro-scale electronic band structure, and micro scale electronic properties of grains and grain boundaries in device-grade CdTe thin films to answer this open question. My research utilized a variety of experimental techniques. Samples were obtained from leading groups fabricating the material and devices. A CdCl 2 anneal is commonly performed as part of this fabrication and its effects were also investigated. Photoluminescence (PL) spectroscopy was employed to study the band structure and defect states in CdTe polycrystals. Cadmium vacancy- and chlorine-related states lead to carrier recombination, as in CdTe films grown by other methods. Comparing polycrystalline and single crystal CdTe, showed that the key to explaining the improved performance of polycrystalline CdTe does

  18. Neuro - Fuzzy Analysis for Silicon Carbide Abrasive Grains ...

    African Journals Online (AJOL)

    The manufacture of abrasives in Nigeria has been severely impeded by the difficulty of identifying suitable local raw materials and the associated local formulation for abrasives with global quality standards. This paper presents a study on application of neuro fuzzy to the formulation of silicon carbide abrasives using locally ...

  19. Effects of Cold Rolling Reduction and Initial Goss Grains Orientation on Texture Evolution and Magnetic Performance of Ultra-thin Grain-oriented Silicon Steel

    OpenAIRE

    LIANG Rui-yang; YANG Ping; MAO Wei-min

    2017-01-01

    The ultra-thin grain-oriented silicon steel strips with a thickness of 0.06-0.12mm were produced by one-step-rolling methods with different Goss-orientation of grain-oriented silicon steel sheets. The effect of cold rolling reduction and initial Goss-orientation of samples on texture evolution and magnetic performance of ultra-thin grain-oriented silicon steel strips was studied by EBSD. The result shows that with the increase of cold rolling reduction and decrease of strips thickness, the re...

  20. UO2 Grain Growth: Developing Phase Field Models for Pore Dragging, Solute Dragging and Anisotropic Grain Boundary Energies

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, K. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Tonks, M. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Zhang, Y. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Biner, B. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-09-28

    A detailed phase field model for the effect of pore drag on grain growth kinetics was implemented in MARMOT. The model takes into consideration both the curvature-driven grain boundary motion and pore migration by surface diffusion. As such, the model accounts for the interaction between pore and grain boundary kinetics, which tends to retard the grain growth process. Our 2D and 3D simulations demonstrate that the model capture all possible pore-grain boundary interactions proposed in theoretical models. For high enough surface mobility, the pores move along with the migrating boundary as a quasi-rigid-body, albeit hindering its migration rate compared to the pore-free case. For less mobile pores, the migrating boundary can separate from the pores. For the pore-controlled grain growth kinetics, the model predicts a strong dependence of the growth rate on the number of pores, pore size, and surface diffusivity in agreement with theroretical models. An evolution equation for the grain size that includes these parameters was derived and showed to agree well with numerical solution. It shows a smooth transition from boundary-controlled kinetics to pore-controlled kinetics as the surface diffusivity decreases or the number of pores or their size increases. This equation can be utilized in BISON to give accurate estimate for the grain size evolution. This will be accomplished in the near future. The effect of solute drag and anisotropy of grain boundary on grain growth will be investigated in future studies.

  1. Roughness of grain boundaries in partly recrystallized aluminum

    DEFF Research Database (Denmark)

    Sun, Jun; Zhang, Yubin; Juul Jensen, Dorte

    2017-01-01

    cold rolled aluminum samples. The results show that particle pinning is not the main reason accounting for recrystallization boundary roughness in the present samples. The roughness is however shown to relate to the deformation microstructure and possible effects of migration rate are discussed...

  2. Annealing Twinning and the Nucleation of Recrystallization at Grain Boundaries

    DEFF Research Database (Denmark)

    Jones, A R.

    1981-01-01

    boundaries during recovery might stimulate nucleation of recrystallization in low stacking fault energy materials. The experimental observations also lead to the implication that the density of recrystallization nuclei formed in such materials may be directly related to the strength of the deformation...

  3. Three-dimensional digital approximations of grain boundary networks in polycrystals

    International Nuclear Information System (INIS)

    Lee, S-B; Rohrer, G S; Rollett, A D

    2014-01-01

    In this work, we offer a set of algorithms that convert a voxellated image to a conformal surface mesh that is targeted for polycrystalline materials containing grains with a wide range of sizes and complex shapes. More specifically, we propose a simple but effective algorithm for approximating the grain boundary networks that are implicit in three-dimensional digital images of polycrystals. The algorithm segments a three-dimensional digital image of a polycrystalline microstructure and then smoothes an interpolated conformal surface mesh of the grain boundary network while maintaining certain characteristic features of the microstructure. It is found that the proposed algorithm successfully approximates the grain boundary network based only on the digital, voxellated images of the polycrystal. Simulated microstructures are used to verify that the resulting mesh qualitatively and quantitatively approximates the true structure, in terms of the displacement of the nodes, the grain volume change and the dihedral angle distribution along triple junctions after smoothing. The effect of the use of the cubic grid for mapping digital microstructures on the grain boundary approximation is also discussed. (paper)

  4. Grain boundary engineering to control the discontinuous precipitation in multicomponent U10Mo alloy

    Energy Technology Data Exchange (ETDEWEB)

    Devaraj, Arun; Kovarik, Libor; Kautz, Elizabeth; Arey, Bruce; Jana, Saumyadeep; Lavender, Curt; Joshi, Vineet

    2018-06-01

    Grain boundaries in metallic alloys often play a crucial role, not only in determining the mechanical properties or thermal stability of alloys, but also in dictating the phase transformation kinetics during thermomechanical processing. We demonstrate that locally stabilized structure and compositional segregation at grain boundaries—“grain boundary complexions”—in a complex multicomponent alloy can be modified to influence the kinetics of cellular transformation during subsequent thermomechanical processing. Using aberration-corrected scanning transmission electron microscopy and atom probe tomography analysis of a metallic nuclear fuel highly relevant to worldwide nuclear non-proliferation efforts —uranium-10 wt% molybdenum (U-10Mo) alloy, new evidence for the existence of grain boundary complexion is provided. We then modified the concentration of impurities dissolved in Υ-UMo grain interiors and/or segregated to Υ-UMo grain boundaries by changing the homogenization treatment, and these effects were used used to retard the kinetics of cellular transformation during subsequent sub-eutectoid annealing in this U-10-Mo alloy during sub-eutectoid annealing. Thus, this work provided insights on tailoring the final microstructure of the U-10Mo alloy, which can potentially improve the irradiation performance of this important class of alloy fuels.

  5. Dislocation reactions, grain boundaries, and irreversibility in two-dimensional lattices using topological tweezers.

    Science.gov (United States)

    Irvine, William T M; Hollingsworth, Andrew D; Grier, David G; Chaikin, Paul M

    2013-09-24

    Dislocations, disclinations, and grain boundaries are topological excitations of crystals that play a key role in determining out-of-equilibrium material properties. In this article we study the kinetics, creation, and annihilation processes of these defects in a controllable way by applying "topological tweezers," an array of weak optical tweezers which strain the lattice by weakly pulling on a collection of particles without grabbing them individually. We use topological tweezers to deterministically control individual dislocations and grain boundaries, and reversibly create and destroy dislocation pairs in a 2D crystal of charged colloids. Starting from a perfect lattice, we exert a torque on a finite region and follow the complete step-by-step creation of a disoriented grain, from the creation of dislocation pairs through their reactions to form a grain boundary and their reduction of elastic energy. However, when the grain is rotated back to its original orientation the dislocation reactions do not retrace. Rather, the process is irreversible; the grain boundary expands instead of collapsing.

  6. Partitioning of water between point defects, dislocations, and grain boundaries in olivine

    Science.gov (United States)

    Tielke, J. A.; Mecklenburgh, J.; Mariani, E.; Wheeler, J.

    2017-12-01

    Estimates of the storage capacity of water in the interior of the Earth and other terrestrial planets vary significantly. One interpretation is that water in planetary interiors exists primarily as hydrogen ions, dissociated from liquid water, that are associated with point defects in the crystal structure of nominally anhydrous minerals. However, dislocations and grain boundaries may contribute significantly to the storage capacity of water in planetary interiors, but hydrogen concentrations in dislocations and grain boundaries are difficult to quantify. To measure the water storage capacity of dislocations and grain boundaries, we are analyzing results from high-temperature and high-pressure experiments where deuterium, a stable isotope of hydrogen, was incorporated into olivine, the dominate phase in the upper mantle. Compared to hydrogen, deuterium concentrations can be determined at much higher spatial resolution using secondary-ion mass spectroscopy. The concentration of deuterium in the samples will also be quantified using Fourier transform infrared spectroscopy for comparison to results for hydrogen-bearing olivine. The spatial distribution of regions with different densities of geometrically-necessary dislocations and the locations of grain boundaries will be determined using electron-backscatter diffraction (EBSD) analyses. Correlation of the concentration of deuterium with dislocation densities and grain boundaries will be used to examine the partitioning of water-derived species between the different types of defects. Ultimately, these data will be used to place more realistic bounds on the storage capacity of water in the interior of Earth and of other terrestrial planets.

  7. Molecular dynamics study on microstructure of near grain boundary

    CERN Document Server

    Wang, J Y; Rifkin, J; Li, D X

    2001-01-01

    The molecular dynamics method is used to simulate a uniaxial tensile deformation of 3.8nm nano-NiAl alloy with curved amorphous-like interfaces at 0K. Plastic deformation behaviour is studied by examining the strain-stress relationship and the microstructural evolution characteristic. Atomic level analysis showed that the micro-strain is essentially heterogeneous in simulated nano-phase samples. The plastic deformation is not only attributed to the plasticity of interfaces, but also accompanied with the plastic shear strain mechanism inside lattice distortion regions and grains.

  8. Xe precipitates at grain boundaries in Al under 1 MeV electron irradiation.

    Energy Technology Data Exchange (ETDEWEB)

    Allen, C. W.

    1998-10-23

    Crystalline nanoprecipitates of Xe have been produced by ion implantation into mazed bicrystalline Al at 300 K, in which the matrix grain boundaries are mainly 90 deg tilt boundaries. Within Al grains, Xe nanocrystals are fee, isotactic with the Al and cuboctohedral in shape with {l_brace}111{r_brace} and {l_brace}100{r_brace} facets. With an off-axial imaging technique, the nanocrystals were structure imaged against a relatively featureless matrix background. In contrast to metal precipitates in Al, such as Pb, Xe precipitates straddling a matrix grain boundary are bicrystals as small as approximately 2 nm in diameter. Larger Xe precipitates tend to avoid boundaries which are inclined away from asymmetrical orientation and which thus have a significant twist component. Under the 1 MeV electron irradiation employed for HREM observation, small Xe nanocrystals near a grain boundary may migrate to the boundary and coalesce with other Xe precipitates. The structural observations are rationalized on a simple geometrical interpretation.

  9. Kinetic origin of grain boundary migration, grain coalescence, and defect reduction in the crystallization of quenched two-dimensional Yukawa liquids

    Science.gov (United States)

    Chen, Meng-Chun; Yang, Chi; I, Lin

    2014-11-01

    The kinetic origin of grain boundary migration, grain coalescence, and defect reduction in the crystallization of quenched two-dimensional Yukawa liquids are numerically investigated. It is found that, in grain coalescence, stick-slip cracking the region in front of the grain boundary into smaller subgrains corotating with small angle, followed by healing, is the key for aligning lattice misorientation and inducing grain boundary stick-slip advance. Cracking is initiated from the weakly interlocked dislocation along its Burgers vector, which in turn causes dislocation motion along the crack. The cascaded scattering and recombination of two dislocations with 60∘ and 120∘ Burgers vector angle difference into two and one dislocations are the major processes for dislocation motion and reduction, respectively, in grain boundary migration. A rough grain boundary with large curvature easily supports the above process and induces high grain boundary mobility. Along a straight smooth grain boundary, the parallel Burgers vectors of the string of dislocations hinder defect reduction and induce coalescence stagnation.

  10. Grain Boundary Sliding in Olivine + Clinopyroxene Aggregates: Weakening Mechanism and Microstructure

    Science.gov (United States)

    Zhao, N.; Hirth, G.; Cooper, R. F.; Kruckenberg, S. C.

    2017-12-01

    Constraining the viscosity of olivine-rich aggregates is critical for modeling geodynamic processes in the upper mantle. The presence of pyroxenes can complicate the rheology of mantle rocks owing to heterogeneous phase boundary properties and the potential impacts of incompatible elements on interface viscosity. Thus, in the grain boundary sliding (GBS) regime, it may be inappropriate to extrapolate flow laws of end-member aggregates to predict the behavior of multiphase aggregates. We deformed mixtures of fine-grained olivine (Ol) and clinopyroxene (Cpx) with various phase ratios in a general shear geometry at a confining pressure of 1.5 GPa, 1100-1200ºC and strain rate of 10­-3-10-5 s-1 to shear strains up to 8.5. We observed a peak stress followed by weakening in each experiment (except for those at 1200ºC), yet at steady state Ol-Cpx samples are substantially weaker than either pure Ol or pure Cpx end members scaled to the same grain size. Flow law parameters are quantified and indicate that the dominant deformation mechanism is reaction-limited diffusional creep. In addition, the results are consistent with a microphysical model that does not require the diffusion of Si (Sundberg & Cooper, 2008), providing an explanation for the observed weakening of olivine and pyroxene aggregates. Olivine exhibits an axial-[010] fabric or a B-type fabric. Analysis of low-angle (2º-10º) boundary axes indicate the activation of (010)[100] slip system, but no evidence for activation of the (010)[001] slip system that is hypothesized to generate a B-type fabric by dislocation creep. In the samples with strong fabric, we sorted the grains by their grain orientation spread (GOS, a measurement of how substructured the grain is or how active the dislocations were in the grain). The low-GOS grains have smaller grain sizes, smaller aspect ratios and weaker shape preferred orientation compared to high-GOS grains. Yet, low-GOS grains also have the strongest B-type fabric, while

  11. RETRACTED ARTICLE: The Effect of Solute Atoms on Grain Boundary Migration: A Solute Pinning Approach

    Science.gov (United States)

    Hersent, Emmanuel; Marthinsen, Knut; Nes, Erik

    2012-12-01

    The effect of solute atoms on grain boundary migration has been modeled on the basis of the idea that solute atoms will locally perturb the collective rearrangements of solvent atoms associated with boundary migration. The consequence of such perturbations is the cusping of the boundary and corresponding stress concentrations on the solute atoms which will promote thermal activation of these atoms out of the boundary. This thermal activation is considered to be the rate-controlling mechanism in boundary migration. It is demonstrated that the present statistical approach is capable of explaining, in phenomenological terms, the known effects of solute atoms on boundary migration. The experimental results on the effect of copper on boundary migration in aluminum, due to Gordon and Vandermeer, have been well accounted for.

  12. Accurate electron channeling contrast analysis of a low angle sub-grain boundary

    International Nuclear Information System (INIS)

    Mansour, H.; Crimp, M.A.; Gey, N.; Maloufi, N.

    2015-01-01

    High resolution selected area channeling pattern (HR-SACP) assisted accurate electron channeling contrast imaging (A-ECCI) was used to unambiguously characterize the structure of a low angle grain boundary in an interstitial-free-steel. The boundary dislocations were characterized using TEM-style contrast analysis. The boundary was determined to be tilt in nature with a misorientation angle of 0.13° consistent with the HR-SACP measurements. The results were verified using high accuracy electron backscatter diffraction (EBSD), confirming the approach as a discriminating tool for assessing low angle boundaries

  13. The Potential Link Between High Angle Grain Boundary Morphology and Grain Boundary Deformation in a Nickel-Based Superalloy (Postprint)

    Science.gov (United States)

    2015-06-01

    was utilized to align the stack of images within a subpixel . Next, a levels adjustment was applied to stretch the intensity histogram to maximize...boundary axis and angle of misorientation and the axis and angle of misorientation for Σ11 are 2.43° and 1°, respectively. Fig. 6 is a rendering of

  14. Reconstruction of 3d grain boundaries from rock thin sections, using polarised light

    Science.gov (United States)

    Markus Hammes, Daniel; Peternell, Mark

    2016-04-01

    Grain boundaries affect the physical and chemical properties of polycrystalline materials significantly by initiating reactions and collecting impurities (Birchenall, 1959), and play an essential role in recrystallization (Doherty et al. 1997). In particular, the shape and crystallographic orientation of grain boundaries reveal the deformation and annealing history of rocks (Kruhl and Peternell 2002, Kuntcheva et al. 2006). However, there is a lack of non-destructive and easy-to-use computer supported methods to determine grain boundary geometries in 3D. The only available instrument using optical light to measure grain boundary angles is still the polarising microscope with attached universal stage; operated manually and time-consuming in use. Here we present a new approach to determine 3d grain boundary orientations from 2D rock thin sections. The data is recorded by using an automatic fabric analyser microscope (Peternell et al., 2010). Due to its unique arrangement of 9 light directions the highest birefringence colour due to each light direction and crystal orientation (retardation) can be determined at each pixel in the field of view. Retardation profiles across grain boundaries enable the calculation of grain boundary angle and direction. The data for all positions separating the grains are combined and further processed. In combination with the lateral position of the grain boundary, acquired using the FAME software (Hammes and Peternell, in review), the data is used to reconstruct a 3d grain boundary model. The processing of data is almost fully automatic by using MATLAB®. Only minor manual input is required. The applicability was demonstrated on quartzite samples, but the method is not solely restricted on quartz grains and other birefringent polycrystalline materials could be used instead. References: Birchenall, C.E., 1959: Physical Metallurgy. McGraw-Hill, New York. Doherty, R.D., Hughes, D.A., Humphreys, F.J., Jonas, J.J., Juul Jensen, D., Kassner, M

  15. Grain Boundary Structures and Collective Dynamics of Inversion Domains in Binary Two-Dimensional Materials

    Science.gov (United States)

    Taha, Doaa; Mkhonta, S. K.; Elder, K. R.; Huang, Zhi-Feng

    2017-06-01

    Understanding and controlling the properties and dynamics of topological defects is a lasting challenge in the study of two-dimensional materials, and is crucial to achieve high-quality films required for technological applications. Here grain boundary structures, energies, and dynamics of binary two-dimensional materials are investigated through the development of a phase field crystal model that is parametrized to match the ordering, symmetry, energy, and length scales of hexagonal boron nitride. Our studies reveal some new dislocation core structures for various symmetrically and asymmetrically tilted grain boundaries, in addition to those obtained in previous experiments and first-principles calculations. We also identify a defect-mediated growth dynamics for inversion domains governed by the collective atomic migration and defect core transformation at grain boundaries and junctions, a process that is related to inversion symmetry breaking in binary lattice.

  16. Improvement of corrosion resistance in austenitic stainless steel by grain boundary character distribution control

    International Nuclear Information System (INIS)

    Wang, Yun; Kaneda, Junya; Kasahara, Shigeki; Shigenaka, Naoto

    2012-01-01

    Strauss test, Coriou test and Huey test were conducted on a Type 316L austenitic stainless steel. Improvement in grain boundary corrosion resistance was verified after raising low Σ coincidence site lattice (CSL) grain boundary (GB) frequency by controlling grain boundary character distribution (GBCD). During crevice corrosion test under gamma-ray irradiation, initiation frequency of GB corrosion after GBCD controlled specimens decreased to 1/10 of GBCD uncontrolled counterpart along with lower depth of corrosion. Stress corrosion cracking (SCC) propagation rate of GBCD controlled specimen decreased to less than 1/2 of GBCD uncontrolled specimen in high temperature and high pressure water. Based on these results, we expect that GBCD control will improve corrosion resistance of austenitic material in a wide range of application and environment. (author)

  17. MARMOT simulations of Xe segregation to grain boundaries in UO2

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Anders D. [Los Alamos National Laboratory; Tonks, Michael [Idaho National Laboratory; Casillas, Luis [Los Alamos National Laboratory; Millett, Paul [Idaho National Laboratory; Vyas, Shyam [Los Alamos National Laboratory; Uberuaga, Blas P. [Los Alamos National Laboratory; Nerikar, Pankaj [IBM

    2012-06-20

    Diffusion of Xe and U in UO{sub 2} is controlled by vacancy mechanisms and under irradiation the formation of mobile vacancy clusters is important. We derive continuum thermodynamic and diffusion models for Xe and U in UO{sub 2} based on the vacancy and cluster diffusion mechanisms established from recent density functional theory (DFT) calculations. Segregation of defects to grain boundaries in UO{sub 2} is described by combining the diffusion model with models of the interaction between Xe atoms and vacancies with grain boundaries derived from separate atomistic calculations. The diffusion and segregation models are implemented in the MOOSE/MARMOT (MBM) finite element (FEM) framework and we simulate Xe redistribution for a few simple microstructures. In this report we focus on segregation to grain boundaries. The U or vacancy diffusion model as well as the coupled diffusion of vacancies and Xe have also been implemented, but results are not included in this report.

  18. Plastic deformation-induced phosphorus segregation to ferrite grain boundaries in an interstitial free steel

    International Nuclear Information System (INIS)

    Chen, X.-M.; Song, S.-H.

    2010-01-01

    Research highlights: → Plastic deformation causes non-equilibrium grain boundary phosphorus segregation. → Deformation induced segregation increases with increasing deformation rate. → Non-equilibrium segregation is induced by supersaturated vacancy-phosphorus complex. → Model predictions show a reasonable agreement with the observations. - Abstract: Grain boundary concentration of phosphorus in an interstitial free steel is observed by virtue of Auger electron spectroscopy after the alloy is plastically deformed to different strains under different strain rates at a high temperature in the ferrite region. The results reveal that phosphorus segregates at grain boundaries during plastic deformation. The segregation increases with increasing deformation until reaching a steady value, and at the same deformation amount it increases with increasing strain rate. Model predictions are made, which shows a reasonable agreement between the predictions and the observations.

  19. Atom Probe Tomography Studies on the Cu(In,Ga)Se2 Grain Boundaries

    Science.gov (United States)

    Cojocaru-Mirédin, Oana; Schwarz, Torsten; Choi, Pyuck-Pa; Herbig, Michael; Wuerz, Roland; Raabe, Dierk

    2013-01-01

    Compared with the existent techniques, atom probe tomography is a unique technique able to chemically characterize the internal interfaces at the nanoscale and in three dimensions. Indeed, APT possesses high sensitivity (in the order of ppm) and high spatial resolution (sub nm). Considerable efforts were done here to prepare an APT tip which contains the desired grain boundary with a known structure. Indeed, site-specific sample preparation using combined focused-ion-beam, electron backscatter diffraction, and transmission electron microscopy is presented in this work. This method allows selected grain boundaries with a known structure and location in Cu(In,Ga)Se2 thin-films to be studied by atom probe tomography. Finally, we discuss the advantages and drawbacks of using the atom probe tomography technique to study the grain boundaries in Cu(In,Ga)Se2 thin-film solar cells. PMID:23629452

  20. Direct observation of liquid-like behavior of a single Au grain boundary.

    Science.gov (United States)

    Casillas, Gilberto; Ponce, Arturo; Velázquez-Salazar, J Jesús; José-Yacamán, Miguel

    2013-07-21

    Behavior of matter at the nanoscale differs from that of the bulk due to confinement and surface effects. Here, we report a direct observation of liquid-like behavior of a single grain boundary formed by cold-welding Au nanoparticles, 40 nm in size, by mechanical manipulation in situ TEM. The grain boundary rotates almost freely due to the free surfaces and can rotate about 90 degrees. The grain boundary sustains more stress than the bulk, confirming a strong bonding between the nanoparticles. Moreover, this technique allows the measurement of the surface diffusion coefficient from experimental observations, which we compute for the Au nanoparticles. This methodology can be used for any metal, oxide, semiconductor or combination of them.

  1. Segregation and structural transformations at Σ = 3 grain boundaries in NiAl: A Monte-Carlo study

    International Nuclear Information System (INIS)

    Brown, J.A.; Mishin, Y.

    2005-01-01

    Grain boundary structure and grain boundary segregation in stoichiometric and Ni-rich compositions of NiAl are studied by molecular statics and grand-canonical Monte-Carlo simulations in conjunction with an embedded-atom potential. Significant Ni segregation is found at the Σ = 3(1 1 1) and Σ = 3(2 1 1) grain boundaries, with segregation isotherms showing a saturation effect. The amount of Ni segregation increases and the excess free energy of the grain boundaries decreases with increased Ni bulk concentration. In strongly Ni-rich bulk compositions, both boundaries undergo transformations to new structures capable of accommodating more excess Ni atoms than the initial structures. The structural transformation is clearly manifested by a non-monotonic behavior of the segregation isotherm. In the Σ = 3(2 1 1) grain boundary, the transformation is accompanied by a relative tangential translation of the grains

  2. Effect of -bar 2 grain boundaries on plastic deformation of WC-Co cemented carbides

    Energy Technology Data Exchange (ETDEWEB)

    Ostberg, G. [Department of Applied Physics, Chalmers University of Technology, SE-412 96 Goeteborg (Sweden)]. E-mail: gusto@fy.chalmers.se; Farooq, M.U. [Department of Materials and Manufacturing Technology, Chalmers University of Technology, SE-412 96 Goeteborg (Sweden); Christensen, M. [Department of Applied Physics, Chalmers University of Technology, SE-412 96 Goeteborg (Sweden); Andren, H.-O. [Department of Applied Physics, Chalmers University of Technology, SE-412 96 Goeteborg (Sweden); Klement, U. [Department of Materials and Manufacturing Technology, Chalmers University of Technology, SE-412 96 Goeteborg (Sweden); Wahnstroem, G. [Department of Applied Physics, Chalmers University of Technology, SE-412 96 Goeteborg (Sweden)

    2006-01-25

    Cutting inserts of WC-6wt.% Co were investigated before and after plastic deformation. The deformation tests were performed with a turning operation under realistic, yet controlled, conditions. SEM studies showed that after deformation the WC skeleton structure had broken up and thin lamellae of binder phase had formed in less than 10% of the grain boundaries. Ab initio calculations showed that -bar 2 twist WC/WC boundaries have a high work of separation and the interface energy is not lowered by forming two Co/WC boundaries. Electron backscattered diffraction (EBSD) measurements showed an apparent increase in the relative occurrence of -bar 2 boundaries due to poor indexing of the deformed material. The accumulation of dislocations in general boundaries is held responsible for the difficulty in identifying them compared with -bar 2 boundaries. At the -bar 2 tilt boundary the grains have the glide planes {l_brace}101-bar 0{r_brace} in common and at the -bar 2 twist boundary there are three glide planes intersecting, which facilitate dislocation movements across the -bar 2 boundaries.

  3. SEM-analysis of grain boundary porosity in three S-176 specimens

    International Nuclear Information System (INIS)

    Malen, K.; Birath, S.; Mattsson, O.

    1980-10-01

    Porosity in UO 2 -fuel has been studied in scanning electron microscope (SEM). The aim was to obtain a basis for evaluation of porosity in high burnup power reactor fuel. Three specimens have been analyzed. In the high temperature zones porosity can be seen both on grain boundaries and at grain edges. In the low temperature regions very little changes seem to have occurred during irradiation. (author)

  4. Columns formed by multiple twinning in nickel layers—An approach of grain boundary engineering by electrodeposition

    DEFF Research Database (Denmark)

    Alimadadi, Hossein; da Silva Fanta, Alice Bastos; Somers, Marcel A. J.

    2013-01-01

    grain boundaries. A peculiar arrangement of Σ3 boundaries forming five-fold junctions is observed. The resulting microstructure meets the requirements for grain boundary engineering. Twinning induced effects on the crystallographic orientation of grains result in one major texture component being a ⟨210......⟩ fiber axis and additional minor orientations originating from first and second generation twins of ⟨210⟩, i.e., ⟨542⟩ and ⟨20 2 1⟩....

  5. Relations and interactions between twinning and grain boundaries in hexagonal close-packed structures

    Science.gov (United States)

    Barrett, Christopher Duncan

    Improving the formability and crashworthiness of wrought magnesium alloys are the two biggest challenges in current magnesium technology. Magnesium is the best material candidate for enabling required improvements in fuel economy of combustion engines and increases in ranges of electric vehicles. In hexagonal closed-packed (HCP) structures, effects of grain size/morphology and crystallographic texture are particularly important. Prior research has established a general understanding of the dependences of strength and strain anisotropy on grain morphology and texture. Unfortunately, deformation, recrystallization, and grain growth strategies that control the microstructures and textures of cubic metals and alloys have not generally worked for HCPs. For example, in Magnesium, the deformation texture induced by primary forming operations (rolling, extrusion, etc.) is not randomized by recrystallization and may strengthen during grain growth. A strong texture reduces formability during secondary forming (stamping, bending, hemming etc.) Thus, the inability to randomize texture has impeded the implementation of magnesium alloys in engineering applications. When rare earth solutes are added to magnesium alloys, distinct new textures are derived. However, `rare earth texture' derivation remains insufficiently explained. Currently, it is hypothesized that unknown mechanisms of alloy processing are at work, arising from the effects of grain boundary intrinsic defect structures on microstructural evolution. This dissertation is a comprehensive attempt to identify formal methodologies of analyzing the behavior of grain boundaries in magnesium. We focus particularly on twin boundaries and asymmetric tilt grain boundaries using molecular dynamics. We begin by exploring twin nucleation in magnesium single crystals, elucidating effects of heterogeneities on twin nucleation and their relationships with concurrent slip. These efforts highlighted the necessity of imperfections to

  6. Dissolution kinetics of nanoscale liquid Pb/Bi inclusions at a grain boundary in aluminum

    DEFF Research Database (Denmark)

    Prokofjev, S.I.; Johnson, Erik; Zhilin, V.M.

    2008-01-01

    . Dissolution of the inclusions was observed until their complete disappearance. Digitized video recordings of the process of dissolution were used to obtain the dependence of the inclusion size with time. The kinetics of the dissolution of the grain boundary inclusions can be described with a model where......In situ transmission electron microscopy is used to study dissolution of liquid single-phase Pb/Bi inclusions attached to a grain boundary in an alloy of Al99.29Pb0.65Bi0.06 at temperatures of 343, 370, and 389 degrees C, respectively. The initial size of the inclusions was smaller than 60 nm...

  7. Investigation of the role of grain boundary on the mechanical properties of metals

    International Nuclear Information System (INIS)

    Kheradmand, Nousha; Barnoush, Afrooz; Vehoff, Horst

    2010-01-01

    Compression testing of micropillars was used to investigate the gain boundary effect on the strength of metals which is especially interesting in ultra fine grained and nanocrystalline metals. Single and bicrystal micropillars of different sizes and crystallographic orientations were fabricated using a focused ion beam system and the compression test was performed with a nanoindenter. A reduction of the pillar size as well as the introduction of a grain boundary results in an increase in the yield strength. The results show that the size and the orientation of different adjoining crystals in bicrystalline pillars have an obvious effect on dislocation nucleation and multiplication.

  8. Estimation of grain boundary diffusivity in near-α titanium polycrystals

    International Nuclear Information System (INIS)

    Brockman, Robert A.; Pilchak, Adam L.; John Porter, W.; John, Reji

    2011-01-01

    The role of enhanced grain boundary diffusivity in high-temperature diffusion of interstitial elements through metals is widely recognized but poorly characterized in most materials. This paper summarizes an effort to estimate grain boundary diffusivity of oxygen in a near-α titanium alloy, Ti-6Al-2Sn-4Zr-2Mo-0.1Si, by explicitly incorporating microstructure obtained from electron backscatter diffraction into an analytical model. Attention is focused on near-surface diffusion behavior contributing to the rapid ingress of oxygen and possible crack initiation in high-temperature environments.

  9. Molecular dynamics studies of irradiation effects on hydrogen isotope diffusion through nickel crystals and grain boundaries.

    Science.gov (United States)

    Zhou, X W; Dingreville, R; Karnesky, R A

    2017-12-20

    Experiments indicated that tritium permeation in 316 austenitic stainless steel is enhanced by a factor of ∼2-5 after irradiation as compared to the ex-reactor results. To understand this enhancement, we have performed extensive molecular dynamics simulations to study the effects of both the grain boundary structure (Σ3{111}, Σ5{100} and Σ11{311}) and the nature of point defects (vacancy, interstitial, and Frenkel pair) on hydrogen diffusivities in an exemplar fcc metal (nickel). By deriving diffusivities from mean square displacement, all possible atomic jump paths encountered during real diffusion are realistically sampled. By performing extremely long simulations, the statistical errors typically associated with this method are also significantly reduced. We found that within grains, interstitial defects increase diffusivity whereas vacancies have almost no effects. This mechanism might explain hydrogen permeation enhancements in irradiated materials with coarse grains. The largest increase in hydrogen diffusivity was found at a certain combination of grain boundary and point defect. This suggests that permeability of materials with finer grains can also be enhanced by irradiation depending on whether the grain boundary character is skewed. Our results shed new light on the enhancement of tritium permeation in 316 stainless steels during reactor operations.

  10. Tribological characteristics of few-layer graphene over Ni grain and interface boundaries.

    Science.gov (United States)

    Tripathi, Manoj; Awaja, Firas; Paolicelli, Guido; Bartali, Ruben; Iacob, Erica; Valeri, Sergio; Ryu, Seunghwa; Signetti, Stefano; Speranza, Giorgio; Pugno, Nicola Maria

    2016-03-28

    The tribological properties of metal-supported few-layered graphene depend strongly on the grain topology of the metal substrate. Inhomogeneous distribution of graphene layers at such regions led to variable landscapes with distinguishable roughness. This discrepancy in morphology significantly affects the frictional and wetting characteristics of the FLG system. We discretely measured friction characteristics of FLG covering grains and interfacial grain boundaries of polycrystalline Ni metal substrate via an atomic force microscopy (AFM) probe. The friction coefficient of FLG covered at interfacial grain boundaries is found to be lower than that on grains in vacuum (at 10(-5) Torr pressure) and similar results were obtained in air condition. Sliding history with AFM cantilever, static and dynamic pull-in and pull-off adhesion forces were addressed in the course of friction measurements to explain the role of the out-of-plane deformation of graphene layer(s). Finite element simulations showed good agreement with experiments and led to a rationalization of the observations. Thus, with interfacial grain boundaries the FLG tribology can be effectively tuned.

  11. Grain Boundary Evolution of Cold-Rolled FePd Alloy during Recrystallization at Disordering Temperature

    Science.gov (United States)

    Lin, Hung-Pin; Chen, Delphic; Kuo, Jui-Chao

    2015-01-01

    In this study, the grain boundary character and texture of 50% and 90% cold-rolled FePd alloy was investigated during recrystallization at 700 °C. Electron backscatter diffraction (EBSD) measurements were performed on the rolling direction to normal direction section. Kernel average misorientation (KAM) calculated from EBSD measurements was employed to determine the recrystallization fraction. The Avrami exponent n of recrystallization is 1.9 and 4.9 for 50% and 90% cold rolling, respectively. The new formation of texture reveals random texture during the recrystallization process. As annealing time increased, the number of high angle boundary (HAGB) and coincidence site lattice (CSL) increased with consumption of low angle boundary (LAGB). In addition, possible transformations between different grain boundaries are observed here.

  12. Study of nanophase TiO2 grain boundaries by Raman spectroscopy

    International Nuclear Information System (INIS)

    Melendres, C.A.; Narayanasamy, A.; Maroni, V.A.; Siegel, R.W.

    1989-01-01

    Raman spectra have been recorded for as-consolidated nanophase TiO 2 samples with differing grain sizes and on samples annealed in air at a variety of temperatures up to 1273 K. The nanophase samples with the smallest grain size, about 12 nm average diameter, could have 15-30% of their atoms in grain boundaries; nevertheless, the strong Raman-active lines representative of the rutile structure were found to dominate all of the observed spectra, independent of grain size and annealing treatment. These lines were quite broad in the as-consolidated nanophase samples, equally in 12 nm and 100 nm grain-size compacts, but sharpened considerably upon annealing at elevated temperatures. The Raman data give no indication of grain-boundary structures in nanophase TiO 2 that are significantly different from those in conventional polycrystals. However, defect structures within the grains, which anneal out at elevated temperatures, are evidenced by changes in the Raman spectra. 15 refs., 2 figs

  13. Effect of grain alignment on interface trap density of thermally oxidized aligned-crystalline silicon films

    Science.gov (United States)

    Choi, Woong; Lee, Jung-Kun; Findikoglu, Alp T.

    2006-12-01

    The authors report studies of the effect of grain alignment on interface trap density of thermally oxidized aligned-crystalline silicon (ACSi) films by means of capacitance-voltage (C-V) measurements. C-V curves were measured on metal-oxide-semiconductor (MOS) capacitors fabricated on ⟨001⟩-oriented ACSi films on polycrystalline substrates. From high-frequency C-V curves, the authors calculated a decrease of interface trap density from 2×1012to1×1011cm-2eV-1 as the grain mosaic spread in ACSi films improved from 13.7° to 6.5°. These results demonstrate the effectiveness of grain alignment as a process technique to achieve significantly enhanced performance in small-grained (⩽1μm ) polycrystalline Si MOS-type devices.

  14. Analysis of grain growth process in melt spun Fe-B alloys under the initial saturated grain boundary segregation condition

    International Nuclear Information System (INIS)

    Chen, Z.; Liu, F.; Yang, X.Q.; Fan, Y.; Shen, C.J.

    2012-01-01

    Highlights: → We compared pure kinetic, pure thermodynamic and extended thermo-kinetic models. → An initial saturated GB segregation condition of nanoscale Fe-B alloys was determined. → The controlled-mechanism was proposed using two characteristic times (t 1 and t 2 ). - Abstract: A grain growth process in the melt spun low-solid-solubility Fe-B alloys was analyzed under the initial saturated grain boundary (GB) segregation condition. Applying melt spinning technique, single-phase supersaturated nanograins were prepared. Grain growth behavior of the single-phase supersaturated nanograins was investigated by performing isothermal annealing at 700 deg. C. Combined with the effect of GB segregation on the initial GB excess amount, the thermo-kinetic model [Chen et al., Acta Mater. 57 (2009) 1466] was extended to describe the initial GB segregation condition of nanoscale Fe-B alloys. In comparison of pure kinetic model, pure thermodynamic model and the extended thermo-kinetic model, an initial saturated GB segregation condition was determined. The controlled-mechanism of grain growth under initial saturated GB segregation condition was proposed using two characteristic annealing times (t 1 and t 2 ), which included a mainly kinetic-controlled process (t ≤ t 1 ), a transition from kinetic-mechanism to thermodynamic-mechanism (t 1 2 ) and pure thermodynamic-controlled process (t ≥ t 2 ).

  15. Nanocompositional Electron Microscopic Analysis and Role of Grain Boundary Phase of Isotropically Oriented Nd-Fe-B Magnets

    Directory of Open Access Journals (Sweden)

    Gregor A. Zickler

    2017-01-01

    Full Text Available Nanoanalytical TEM characterization in combination with finite element micromagnetic modelling clarifies the impact of the grain misalignment and grain boundary nanocomposition on the coercive field and gives guidelines how to improve coercivity in Nd-Fe-B based magnets. The nanoprobe electron energy loss spectroscopy measurements obtained an asymmetric composition profile of the Fe-content across the grain boundary phase in isotropically oriented melt-spun magnets and showed an enrichment of iron up to 60 at% in the Nd-containing grain boundaries close to Nd2Fe14B grain surfaces parallel to the c-axis and a reduced iron content up to 35% close to grain surfaces perpendicular to the c-axis. The numerical micromagnetic simulations on isotropically oriented magnets using realistic model structures from the TEM results reveal a complex magnetization reversal starting at the grain boundary phase and show that the coercive field increases compared to directly coupled grains with no grain boundary phase independently of the grain boundary thickness. This behaviour is contrary to the one in aligned anisotropic magnets, where the coercive field decreases compared to directly coupled grains with an increasing grain boundary thickness, if Js value is > 0.2 T, and the magnetization reversal and expansion of reversed magnetic domains primarily start as Bloch domain wall at grain boundaries at the prismatic planes parallel to the c-axis and secondly as Néel domain wall at the basal planes perpendicular to the c-axis. In summary our study shows an increase of coercive field in isotropically oriented Nd-Fe-B magnets for GB layer thickness > 5 nm and an average Js value of the GB layer < 0.8 T compared to the magnet with perfectly aligned grains.

  16. Dissolution of kinetics of nanoscale liquid Pb/Bi inclusions at a grain boundary in aluminium

    DEFF Research Database (Denmark)

    Prokofjev, Sergei I.; Johnson, Erik; Zhilin, Victor M.

    2008-01-01

    of the inclusions was observed until their complete disappearance. Digitized video recordings of the process of dissolution were used to obtain the dependence of the inclusion size with time. The kinetics of the dissolution of the grain boundary inclusions can be described with a model where it is assumed...

  17. Mean-field model for the growth and coarsening of stoichiometric precipitates at grain boundaries

    Czech Academy of Sciences Publication Activity Database

    Kozeschnik, E.; Svoboda, Jiří; Radis, R.; Fischer, F. D.

    2010-01-01

    Roč. 18, č. 1 (2010), Art. No. 015011 ISSN 0965-0393 R&D Projects: GA MŠk(CZ) OC10029 Institutional research plan: CEZ:AV0Z20410507 Keywords : precipitation * growth * grain boundary Subject RIV: BJ - Thermodynamic s Impact factor: 1.374, year: 2010

  18. Influence of phosphorus grain boundary segregation on fracture behaviour of iron-base alloys

    Czech Academy of Sciences Publication Activity Database

    Janovec, J.; Pokluda, J.; Lejček, Pavel

    567-568, - (2007), s. 33-38 ISSN 0255-5476 Institutional research plan: CEZ:AV0Z10100520 Keywords : austenitic stainless steel * Fe-Si-P alloy * grain boundary segregation precipitation * instrumented impact test * Auger elektron spectroscopy * transmission elektron microscopy Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.399, year: 2005

  19. Silicalite-1 polycrystalline layers and crystal twins: Morphology and grain boundaries

    Czech Academy of Sciences Publication Activity Database

    Brabec, Libor; Kočiřík, Milan

    2007-01-01

    Roč. 102, č. 1 (2007), s. 67-74 ISSN 0254-0584 R&D Projects: GA ČR GA203/05/0846 Institutional research plan: CEZ:AV0Z40400503 Keywords : silicalite-1 * HF acid * etching * grain boundaries Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.871, year: 2007

  20. Effect of solute interaction on interfacial and grain boundary embrittlement in binary alloys

    Czech Academy of Sciences Publication Activity Database

    Lejček, Pavel

    2013-01-01

    Roč. 48, č. 6 (2013), 2574-2580 ISSN 0022-2461 R&D Projects: GA ČR GAP108/12/0144 Institutional research plan: CEZ:AV0Z10100520 Keywords : interfacial segregation * grain boundary embrittlement * binary interaction * modeling * thermodynamics Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.305, year: 2013

  1. Grain Boundary Related Effects in Aluminium during 600 MeV Proton Irradiation of Different Temperatures

    DEFF Research Database (Denmark)

    Singh, Bachu Narain; Leffers, Torben; Green, W.V.

    1984-01-01

    Samples of high-purity aluminium were irradiated with 600 MeV protons at temperatures in the range 130 to 433°C; in these experiments 615 and 125 appm of hydrogen and helium, respectively, are produced per dpa. Bubble formation and growth at grain boundaries and in the zone adjacent to the bubble...

  2. Surface roughness and grain boundary scattering effects on the electrical conductivity of thin films

    NARCIS (Netherlands)

    Palasantzas, George

    1998-01-01

    In this work, we investigate surface/interface roughness and grain boundary scattering effects on the electrical conductivity of polycrystalline thin films in the Born approximation. We assume for simplicity a random Gaussian roughness convoluted with a domain size distribution ~e^-πr^2/ζ^2 to

  3. Continuum Description of Atomistics for Nanomechanics of Grain Boundary Embrittlement in FCC Metals

    Science.gov (United States)

    Kim, K.-S.; Wang, C.-K.; Cha, M.-H.; Chew, H. B.

    2012-02-01

    A nonlinear field projection method has been developed to study nanometer scale mechanical properties of grain boundaries in nanocrystalline FCC metals [1]. The nonlinear field projection is based on the principle of virtual work, for virtual variations of atomic positions in equilibrium through nonlocal interatomic interactions such as EAM potential interaction, to get field-projected subatomic-resolution traction distributions on various grain boundaries. The analyses show that the field projected traction produces periodic concentrated compression sites on the grain boundary, which act as crack trapping or dislocation nucleation sites. The field projection was also used to assess the nanometer scale failure processes of Cu σ5 and σ9 grain boundaries doped with Pb. It was revealed that the most significant atomic rearrangement is dislocation emission which requires local GB slip, and some Pb locks the local GB slip and in turn, embrittles the GB. Reference: [1] C.-K. Wang, et al., 2011, MRS Proceedings, Vol. 1297, DOI: 10.1557/opl.2011.678.

  4. In-situ transmission electron microscopy : on moving dislocations and mobile grain boundaries

    NARCIS (Netherlands)

    De Hosson, J. T. M.; Soer, W.

    This paper delineates the possibilities of utilizing in situ transmission electron microscopy to unravel dislocation-g rain boundary interactions. In situ nanoindentation experiments have been conducted in TEM on ultrafine-grained Al and Al-Mg films with varying Mg contents. The observed propagation

  5. Structure And Mobilities Of Tungsten Grain Boundaries Calculated From Atomistic Simulations

    Energy Technology Data Exchange (ETDEWEB)

    Frolov, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Rudd, R. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-08-09

    The objective of this study is to develop a computational methodology to predict structure, energies and mobilities of tungsten grain boundaries as a function of misorientation and inclination. The energies and the mobilities are the necessary input for thermomechanical model of recrystallization being developed by the Marian Group at UCLA.

  6. Graphene quantum dot incorporated perovskite films: passivating grain boundaries and facilitating electron extraction.

    Science.gov (United States)

    Fang, Xiang; Ding, Jianning; Yuan, Ningyi; Sun, Peng; Lv, Minghang; Ding, Guqiao; Zhu, Chong

    2017-02-22

    Organic-inorganic halide perovskites have emerged as attractive materials for use in photovoltaic cells. Owing to the existence of dangling bonds at the grain boundaries between perovskite crystals, minimizing the charge recombination at the surface or grain boundaries by passivating these trap states has been identified to be one of the most important strategies for further optimization of device performance. Previous reports have mainly focused on surface passivation by inserting special materials such as graphene or fullerene between the electron transfer layer and the perovskite film. Here, we report an enhanced efficiency of mesoscopic perovskite solar cells by using graphene quantum dots (GQDs) to passivate the grain boundaries of CH 3 NH 3 PbI 3 . The highest efficiency (17.62%) is achieved via decoration with 7% GQDs, which is an 8.2% enhancement with respect to a pure perovskite based device. Various analyses including electrochemical impedance spectroscopy, time-resolved photoluminescence decay and open-circuit voltage decay measurements are employed in investigating the mechanism behind the improvement in device performance. The findings reveal two important roles played by GQDs in promoting the performance of perovskite solar cells - that GQDs are conducive to facilitating electron extraction and can effectively passivate the electron traps at the perovskite grain boundaries.

  7. A study of deformation-induced phosphorus grain boundary segregation in an interstitial free steel

    International Nuclear Information System (INIS)

    Chen, X.-M.; Song, S.-H.; Weng, L.-Q.; Wang, K.

    2012-01-01

    Highlights: ► Plastic deformation causes non-equilibrium grain boundary segregation of P in an IF steel. ► The segregation increases with increasing deformation strain until reaching a steady level. ► At the same strain the segregation increases with increasing strain rate. ► Model predictions exhibit a reasonable agreement with the observations. - Abstract: Phosphorus grain boundary segregation in an interstitial free (IF) steel deformed at different temperatures and strain rates is measured by virtue of Auger electron spectroscopy (AES). The results reveal that the deformation-induced phosphorus grain boundary segregation has a non-equilibrium characteristic and increases with increasing deformation strain until reaching a steady value. In addition, the segregation of phosphorus increases more apparently for the specimen deformed at a lower temperature or a higher strain rate. Predictions with a kinetic model developed recently show a reasonable fit between the predictions and the observations, which indicates that the model is effective in the prediction of deformation-induced grain boundary segregation.

  8. First Principles Modeling of Segregation of Nd to YAG Grain Boundarie

    Science.gov (United States)

    2007-11-15

    in ceramic YAG material. Continued …. For the stoichiometric surface Al50Y30O120, the segregation energy is much higher (3.63 eV). This result should...implemented in GULP program and understand more on the doping in grain boundary. Lastly, we have treated Nd as trivalent and ignored f electrons. This

  9. Thermodynamic effect of elastic stress on grain boundary segregation of phosphorus in a low alloy steel

    Czech Academy of Sciences Publication Activity Database

    Zheng, L.; Lejček, Pavel; Song, S.; Schmitz, G.; Meng, Y.

    2015-01-01

    Roč. 647, Oct (2015), s. 172-178 ISSN 0925-8388 R&D Projects: GA ČR GAP108/12/0144 Institutional support: RVO:68378271 Keywords : grain boundaries * segregation * elastic stress * thermodynamics * chemical potential * molar volume Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.014, year: 2015

  10. Microstructural aspects of phosphorus grain boundary segregation in low alloy steels

    Czech Academy of Sciences Publication Activity Database

    Perháčová, J.; Grman, D.; Svoboda, Milan; Patscheider, J.; Výrostková, A.; Janovec, J.

    2001-01-01

    Roč. 47, č. 1 (2001), s. 44-49 ISSN 0167-577X Grant - others:VEGA(SK) 2/5161/98 Institutional research plan: CEZ:AV0Z2041904 Keywords : microstructure * grain boundary segregation * low alloy steel Subject RIV: JG - Metallurgy Impact factor: 0.670, year: 2001

  11. Interstitial and substitutional solute segregation at individual grain boundaries of α-iron: data revisited

    Czech Academy of Sciences Publication Activity Database

    Lejček, Pavel; Hofmann, S.

    2016-01-01

    Roč. 28, č. 6 (2016), 1-9, č. článku 064001. ISSN 0953-8984 R&D Projects: GA ČR GAP108/12/0144 Institutional support: RVO:68378271 Keywords : anisotropy * enthalpy- entropy compensation effect * grain boundary * iron solute segregation Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.649, year: 2016

  12. On the segregation behavior of tin and antimony at grain boundaries of polycrystalline bcc iron

    Czech Academy of Sciences Publication Activity Database

    Lejček, Pavel; Šandera, P.; Horníková, J.; Pokluda, J.; Godec, M.

    2016-01-01

    Roč. 363, Feb (2016), 140-144 ISSN 0169-4332 R&D Projects: GA ČR GAP108/12/0144 Institutional support: RVO:68378271 Keywords : grain boundary segregation * tin * antimony * Fe based alloy * AES quantification Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.387, year: 2016

  13. Role of Hf4+ Doping on Oxygen Grain Boundary Diffusion in Alumina

    Science.gov (United States)

    2014-09-01

    purity (99.998%) nickel oxide powder (NiO) was obtained from Alfar Aesar (Ward Hill, MA). The nickel oxide powder was first wet-milled in semiconductor ...Pennycook, L. Luo, M. P. Harmer, " Grain Boundary Complexion Transitions in WO3- and CuO -doped TiOi Bicrystals," Acta Mater., [61] 5 (2013) 1691-1704 58

  14. In situ TEM nanoindentation and dislocation-grain boundary interactions : a tribute to David Brandon

    NARCIS (Netherlands)

    de Hosson, J.T.M.; Soer, W.A.; Minor, A.M.; Shan, Z.W.; Stach, E.A.; Asif, S.A.S.; Warren, O.L.

    2006-01-01

    As a tribute to the scientific work of Professor David Brandon, this paper delineates the possibilities of utilizing in situ transmission electron microscopy to unravel dislocation-grain boundary interactions. In particular, we have focused on the deformation characteristics of Al-Mg films. To this

  15. Grain-boundary effects on the magnetoresistance properties of perovskite manganite films

    International Nuclear Information System (INIS)

    Gupta, A.; Gong, G.Q.; Xiao, G.; Duncombe, P.R.; Lecoeur, P.; Trouilloud, P.; Wang, Y.Y.; Dravid, V.P.; Sun, J.Z.

    1996-01-01

    The role of grain boundaries in the magnetoresistance (MR) properties of the manganites has been investigated by comparing the properties of epitaxial and polycrystalline films of La 0.67 D 0.33 MnO 3-δ (D=Ca,Sr, or vacancies). While the MR in the epitaxial films is strongly peaked near the ferromagnetic transition temperature and is very small at low temperatures, the polycrystalline films show large MR over a wide temperature range down to 5 K. The results are explained in terms of switching of magnetic domains in the grains and disorder-induced canting of Mn spins in the grain-boundary region. copyright 1996 The American Physical Society

  16. Substitutional Boron in Nanodiamond, Bucky-Diamond, and Nanocrystalline Diamond Grain Boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Barnard, Amanda S.; Sternberg, Michael G.

    2006-10-05

    Although boron has been known for many years to be a successful dopant in bulk diamond, efficient doping of nanocrystalline diamond with boron is still being developed. In general, the location, configuration, and bonding structure of boron in nanodiamond is still unknown, including the fundamental question of whether it is located within grains or grain boundaries of thin films and whether it is within the core or at the surface of nanoparticles. Presented here are density functional tight-binding simulations examining the configuration, potential energy surface, and electronic charge of substitutional boron in various types of nanocrystalline diamond. The results predict that boron is likely to be positioned at the surface of isolated particles and at the grain boundary of thin-film samples.

  17. Characterizing Grain-Oriented Silicon Steel Sheet Using Automated High-Resolution Laue X-ray Diffraction

    Science.gov (United States)

    Lynch, Peter; Barnett, Matthew; Stevenson, Andrew; Hutchinson, Bevis

    2017-11-01

    Controlling texture in grain-oriented (GO) silicon steel sheet is critical for optimization of its magnetization performance. A new automated laboratory system, based on X-ray Laue diffraction, is introduced as a rapid method for large scale grain orientation mapping and texture measurement in these materials. Wide area grain orientation maps are demonstrated for both macroetched and coated GO steel sheets. The large secondary grains contain uniform lattice rotations, the origins of which are discussed.

  18. Swelling and gas release of grain-boundary pores in uranium dioxide

    International Nuclear Information System (INIS)

    Schrire, D.I.

    1983-12-01

    The swelling and gas release of overpressured grain boundary pores is sintered unirradiated uranium dioxide were investigated under isothermal conditions. The pores became overpressured when the ambient pressure was reduced, and the excess pressure driving force caused growth and interconnection of the pores, leading to eventual gas release. Swelling was measured continuously by a linear variable differential transformer, and open and closed porosity fractions were determined after the tests by immersion density and quantitative microscopy measurements. The sinter porosity consisted of pores situated on grain faces, grain edges, and grain corners. Isolated pores maintained their equilibrium shape while growing, without any measurable change in dihedral angle. Interconnection occurred predominantly along grain edges, without any evidence of pore sharpening or crack propagation at low driving forces. Extensive open porosity occurred at a threshold density of about 85% TD. There was an almost linear dependence of the initial swelling rate on the driving force, with an activation energy of 200+- 8 kJ/mole, in good agreement with published values of the activation energy for grain boundary diffusion

  19. Possible temperature dependence of the activation energy for grain boundary diffusion in metals

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, J. C.M.; Balluffi, R. W.

    1978-05-01

    The apparent activation energy for existing grain boundary diffusion data shows a tendency to decrease with decreasing temperature. Such a decrease may conceivably be due to at least two causes: (1) The grain boundary diffusion must involve several different types of atomic jumps in the core region, each of which is characterized by a different activation energy. The resulting diffusion is then a weighted average over these jumps. As the temperature is lowered, the jump paths with higher activation energies become progressively ''frozen out.'' If the paths are connected in a parallel arrangement (in analogy to an electrical circuit) the averaged effective activation energy decreases as the temperature is reduced. (2) Experimental results were obtained using polycrystalline samples containing a spectrum of different types of grain boundaries. The overall observed diffusion is, therefore, a weighted average over these boundaries. As the temperature is lowered, the boundaries with the higher activation energies become progressively frozen out and the averaged effective activation energy decreases. (GHT)

  20. Atomic structure of large angle grain boundaries determined by quantitative X-ray diffraction techniques

    International Nuclear Information System (INIS)

    Fitzsimmons, M.R.; Sass, S.L.

    1988-01-01

    Quantitative X-ray diffraction techniques have been used to determine the atomic structure of the Σ = 5 and 13 [001] twist boundaries in Au with a resolution of 0.09 Angstrom or better. The reciprocal lattices of these boundaries were mapped out using synchrotron radiation. The atomic structures were obtained by testing model structures against the intensity observations with a chi square analysis. The boundary structure were modeled using polyhedra, including octahedra, special configurations of tetrahedra and Archimedian anti-prisms, interwoven together by the boundary symmetry. The results of this work point to the possibility of obtaining general rules for grain boundary structure based on X-ray diffraction observations that give the atomic positions with high resolution

  1. Modeling of MnS precipitation during the crystallization of grain oriented silicon steel

    Directory of Open Access Journals (Sweden)

    D. Kalisz

    2015-01-01

    Full Text Available The process of manganese sulfide formation in the course of grain-oriented silicon steel solidification process is described in the paper. Fine dispersive MnS inclusions are grain growth inhibitors and apart from AlN inclusions they contribute to the formation of a privileged texture, i.e. Goss texture. A computer simulation of a high-silicon steel ingot solidification with the use of author’s software has been performed. Ueshima model was adapted for simulating the 3 % Si steel ingot solidification. The calculations accounted for the back diffusion effect according to Wołczyński equation. The computer simulation results are presented in the form of plots representing the process of steel components segregation in a solidifying ingot and curves illustrating the inclusion separation process.

  2. The effect of electron scattering from disordered grain boundaries on the resistivity of metallic nanostructures

    International Nuclear Information System (INIS)

    Arenas, Claudio; Henriquez, Ricardo; Moraga, Luis; Muñoz, Enrique; Munoz, Raul C.

    2015-01-01

    Highlights: • Quantum theory of the resistivity arising from electron-grain boundary scattering in nanometric metallic structures. • The resistivity is controlled by the collective properties of the grain assembly, by the allowed Kronig-Penney (KP) bands and by the electron transmission probability across successive grains. • When the grain diameter d is larger than the electron mean free path l, the increase in resistivity arises mainly from a decrease of the number of states at the Fermi surface that are allowed KP bands. • When the grain diameter d is smaller than the electron mean free path l, the increase in resistivity arises primarily from Anderson localization caused by electron transmission across successive grains. - Abstract: We calculate the electrical resistivity of a metallic specimen, under the combined effects of electron scattering by impurities, grain boundaries, and rough surfaces limiting the film, using a quantum theory based upon the Kubo formalism. Grain boundaries are represented by a one-dimensional periodic array of Dirac delta functions separated by a distance “d” giving rise to a Kronig–Penney (KP) potential. We use the Green's function built from the wave functions that are solutions of this KP potential; disorder is included by incorporating into the theory the probability that an electron is transmitted through several successive grain boundaries. We apply this new theory to analyze the resistivity of samples S1, S2, S7 and S8 measured between 4 and 300 K reported in Appl. Surf. Science273, 315 (2013). Although both the classical and the quantum theories predict a resistivity that agrees with experimental data to within a few percent or better, the phenomena giving rise to the increase of resistivity over the bulk are remarkably different. Classically, each grain boundary contributes to the electrical resistance by reflecting a certain fraction of the incoming electrons. In the quantum description, there are states

  3. Non-destructive analysis of micro texture and grain boundary character from X-ray diffraction contrast tomography

    DEFF Research Database (Denmark)

    King, A.; Herbig, M.; Ludwig, W.

    2010-01-01

    parameter description of the character of individual grain boundaries could previously be produced only by destructive characterization techniques. Statistical analysis of this kind of data can be expected to provide new insight into various physico-chemical processes, driven by the grain boundary energy...

  4. Correlation Between Grain Size Distribution and Silicon and Oxygen Contents at Wadi Arar Sediments, Kingdom of Saudi Arabia

    Directory of Open Access Journals (Sweden)

    M. A. M. Alghamdi

    2017-08-01

    Full Text Available Quartz is the major mineral of Wadi Arar sediments. The top two elements contents are oxygen with 63.96 wt%, followed by silicon with 16.35 wt%. There is a positive, weak to medium correlation between grain size and silicon and oxygen contents. The correlation between oxygen and grain size is four times higher than that of silicon. At grain size ranges between 0.8 and 1.0 mm, both oxygen and silicon show the maximum correlation, which decrease gradually with finer and coarser grain sizes. For each element, the correlation between the element content and grain size is a fourth degree polynomial in the grain size. Theoretically, the best two math models that represent the relation between the grain size distribution and each of individual oxygen and silicon content are y=8.84∙ln(x+39.5 and y=2.26∙ln(x+10.1 respectively, where y represents the element content percentage and x represents the corresponding grain size in mm.

  5. Method of making quasi-grain boundary-free polycrystalline solar cell structure and solar cell structure obtained thereby

    Science.gov (United States)

    Gonzalez, Franklin N.; Neugroschel, Arnost

    1984-02-14

    A new solar cell structure is provided which will increase the efficiency of polycrystalline solar cells by suppressing or completely eliminating the recombination losses due to the presence of grain boundaries. This is achieved by avoiding the formation of the p-n junction (or other types of junctions) in the grain boundaries and by eliminating the grain boundaries from the active area of the cell. This basic concept can be applied to any polycrystalline material; however, it will be most beneficial for cost-effective materials having small grains, including thin film materials.

  6. Analysis of grain boundaries, twin boundaries, and Te precipitates in CdZnTe grown by high-pressure Bridgeman method

    International Nuclear Information System (INIS)

    Heffelfinger, J.R.; Medlin, D.L.; James, R.B.

    1998-03-01

    Grain boundaries and twin boundaries in commercial Cd 1-x Zn x Te, which is prepared by a high pressure Bridgeman technique, have been investigated with transmission electron microscopy, scanning electron microscopy, infrared light microscopy and visible light microscopy. Boundaries inside these materials were found to be decorated with Te precipitates. The shape and local density of the precipitates were found to depend on the particular boundary. For precipitates that decorate grain boundaries, their microstructure was found to consist of a single, saucer shaped grain of hexagonal Te (space group P3 1 21). Analysis of a Te precipitate precipitates by selected area diffraction revealed the Te to be aligned with the surrounding Cd 1-x Zn x Te grains. This alignment was found to match the (111) Cd 1-x Z x Te planes with the (1 bar 101) planes of hexagonal Te. Crystallographic alignments between the Cd 1-x Zn x Te grains were also observed for a high angle grain boundary. The structure of the grain boundaries and the Te/Cd 1-x Zn x Te interface are discussed

  7. Properties of grain boundaries in bulk, melt processed Y-Ba-Cu-O fabricated using bridge-shaped seeds

    Science.gov (United States)

    Shi, Y.-H.; Durrell, J. H.; Dennis, A. R.; Babu, N. Hari; Mancini, C. E.; Cardwell, D. A.

    2012-04-01

    Single grain RE-Ba-Cu-O ((RE)BCO, where RE is a rare earth element or yttrium) bulk superconducting materials have significant potential for a variety of engineering applications due to their ability to trap high magnetic fields. However, it is well known that the presence of grain boundaries coupled with a high angle of misorientation (typically 5°) significantly reduces the critical current density, Jc, in all forms of high temperature superconducting materials. It is of considerable fundamental and technological interest, therefore, to investigate the grain boundary properties of bulk, film and tape (RE)BCO. We report a successful multi-seeding technique for the fabrication of fully aligned, artificial (0° misalignment) grain boundaries within large grain YBCO bulk superconductors using bridge-shaped seeds. The microstructure and critical current densities of the grain boundaries produced by this technique have been studied in detail.

  8. Properties of grain boundaries in bulk, melt processed Y–Ba–Cu–O fabricated using bridge-shaped seeds

    International Nuclear Information System (INIS)

    Shi, Y-H; Durrell, J H; Dennis, A R; Mancini, C E; Cardwell, D A; Hari Babu, N

    2012-01-01

    Single grain RE–Ba–Cu–O ((RE)BCO, where RE is a rare earth element or yttrium) bulk superconducting materials have significant potential for a variety of engineering applications due to their ability to trap high magnetic fields. However, it is well known that the presence of grain boundaries coupled with a high angle of misorientation (typically 5°) significantly reduces the critical current density, J c , in all forms of high temperature superconducting materials. It is of considerable fundamental and technological interest, therefore, to investigate the grain boundary properties of bulk, film and tape (RE)BCO. We report a successful multi-seeding technique for the fabrication of fully aligned, artificial (0° misalignment) grain boundaries within large grain YBCO bulk superconductors using bridge-shaped seeds. The microstructure and critical current densities of the grain boundaries produced by this technique have been studied in detail. (paper)

  9. Multiscale Modeling of Grain Boundary Segregation and Embrittlement in Tungsten for Mechanistic Design of Alloys for Coal Fired Plants

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Jian; Tomar, Vikas; Zhou, Naixie; Lee, Hongsuk

    2013-06-30

    Based on a recent discovery of premelting-like grain boundary segregation in refractory metals occurring at high temperatures and/or high alloying levels, this project investigated grain boundary segregation and embrittlement in tungsten (W) based alloys. Specifically, new interfacial thermodynamic models have been developed and quantified to predict high-temperature grain boundary segregation in the W-Ni binary alloy and W-Ni-Fe, W-Ni-Ti, W-Ni-Co, W-Ni-Cr, W-Ni-Zr and W-Ni-Nb ternary alloys. The thermodynamic modeling results have been experimentally validated for selected systems. Furthermore, multiscale modeling has been conducted at continuum, atomistic and quantum-mechanical levels to link grain boundary segregation with embrittlement. In summary, this 3-year project has successfully developed a theoretical framework in combination with a multiscale modeling strategy for predicting grain boundary segregation and embrittlement in W based alloys.

  10. Evidence for preferential flux flow at the grain boundaries of superconducting RF-quality niobium

    Science.gov (United States)

    Sung, Z.-H.; Lee, P. J.; Gurevich, A.; Larbalestier, D. C.

    2018-04-01

    The question of whether grain boundaries (GBs) in niobium can be responsible for lowered operating field (B RF) or quality factor (Q 0) in superconducting radio frequency (SRF) cavities is still controversial. Here, we show by direct DC transport across planar GBs isolated from a slice of very large-grain SRF-quality Nb that vortices can preferentially flow along the grain boundary when the external magnetic field lies in the GB plane. However, increasing the misalignment between the GB plane and the external magnetic field vector markedly reduces preferential flux flow along the GB. Importantly, we find that preferential GB flux flow is more prominent for a buffered chemical polished than for an electropolished bi-crystal. The voltage-current characteristics of GBs are similar to those seen in low angle grain boundaries of high temperature superconductors where there is clear evidence of suppression of the superconducting order parameter at the GB. While local weakening of superconductivity at GBs in cuprates and pnictides is intrinsic, deterioration of current transparency of GBs in Nb appears to be extrinsic, since the polishing method clearly affect the local GB degradation. The dependence of preferential GB flux flow on important cavity preparation and experimental variables, particularly the final chemical treatment and the angle between the magnetic field and the GB plane, suggests two more reasons why real cavity performance can be so variable.

  11. Low-temperature fracture of high purity iron and its relationship to the grain boundary character

    Energy Technology Data Exchange (ETDEWEB)

    Ofuji, T. (Tohoku Univ., Sendai (Japan). Graduate School of Engineering Daido Special Steel Co. Ltd., Nagoya (Japan)); Suzuki, S. (Tohoku Univ., Sendai (Japan). Inst. of Materials Research Nippon Steel Corp., Tokyo (Japan)); Takai, S. (Tohoku Univ., Sendai (Japan). Inst. of Materials Research); Kimura, H. (Tohoku Univ., Sendai (Japan). Inst. of Materials Research)

    1992-02-01

    Mode of fracture and ductile-brittle transition temperature (DBTT) of high purity iron( 99.999% or higher ) was investigated by using two sets of specimens of different grain boundary character. The specimens having bamboo-type grain structure with high angle boundaries have fractured in the intergranular mode and their DBTT is between 110 and 125 K. Specimens with coarse grain structure have shown fractures in transgranular mode at and below 50 K. DBTT for intergranular fracture(IGF), if any, has been below 4.2 K and this has been in contrast with the the occurance of IGF even at 77K for less pure iron specimens(99.99 % or below). It has been concluded that DBTT for IGF, which has been the common fracture mode in pure iron depends strongly on the purity and grain boundary character of iron spocimens. DBTT has ranged from 125 to 4.2 K or below. Also, specimens of 99.99 % purity have been more susceptible to IGF than the specimens with 99.999 % purity. 8 refs., 6 figs.

  12. Modeling grain boundaries in polycrystals using cohesive elements: Qualitative and quantitative analysis

    International Nuclear Information System (INIS)

    El Shawish, Samir; Cizelj, Leon; Simonovski, Igor

    2013-01-01

    Highlights: ► We estimate the performance of cohesive elements for modeling grain boundaries. ► We compare the computed stresses in ABAQUS finite element solver. ► Tests are performed in analytical and realistic models of polycrystals. ► Most severe issue is found within the plastic grain response. ► Other identified issues are related to topological constraints in modeling space. -- Abstract: We propose and demonstrate several tests to estimate the performance of the cohesive elements in ABAQUS for modeling grain boundaries in complex spatial structures such as polycrystalline aggregates. The performance of the cohesive elements is checked by comparing the computed stresses with the theoretically predicted values for a homogeneous material under uniaxial tensile loading. Statistical analyses are performed under different loading conditions for two elasto-plastic models of the grains: isotropic elasticity with isotropic hardening plasticity and anisotropic elasticity with crystal plasticity. Tests are conducted on an analytical finite element model generated from Voronoi tessellation as well as on a realistic finite element model of a stainless steel wire. The results of the analyses highlight several issues related to the computation of normal and shear stresses. The most severe issue is found within the plastic grain response where the computed normal stresses on a particularly oriented cohesive elements are significantly underestimated. Other issues are found to be related to topological constraints in the modeling space and result in the increased scatter of the computed stresses

  13. Intergranular corrosion in AA5XXX aluminum alloys with discontinuous precipitation at the grain boundaries

    Science.gov (United States)

    Bumiller, Elissa

    The US Navy currently uses AA5xxx aluminum alloys for structures exposed to a marine environment. These alloys demonstrate excellent corrosion resistance over other aluminum alloys (e.g., AA2xxx or AA7xxx) in this environment, filling a niche in the marine structures market when requiring a light-weight alternative to steel. However, these alloys are susceptible to localized corrosion; more specifically, intergranular corrosion (IGC) is of concern. IGC of AA5xxx alloys due to the precipitation of beta phase on the grain boundaries is a well-established phenomenon referred to as sensitization. At high degrees of sensitization, the IGC path is a continuous anodic path of beta phase particles. At lower degrees of sensitization, the beta phase coverage at the grain boundaries is not continuous. The traditional ranges of susceptibility to IGC as defined by ASTM B928 are in question due to recent studies. These studies showed that even at mid range degrees of sensitization where the beta phase is no longer continuous, IGC may still occur. Previous thoughts on IGC of these alloy systems were founded on the idea that once the grain boundary precipitate became discontinuous the susceptibility to IGC was greatly reduced. Additionally, IGC susceptibility has been defined metallurgically by compositional gradients at the grain boundaries. However, AA5xxx alloys show no compositional gradients at the grain boundaries, yet are still susceptible to IGC. The goal of this work is to establish criteria necessary for IGC to occur given no continuous beta phase path and no compositional gradient at the grain boundaries. IGC performance of the bulk alloy system AA5083 has been studied along with the primary phases present in the IGC system: alpha and beta phases using electrochemistry and modeling as the primary tools. Numerical modeling supports that at steady-state the fissure tip is likely saturated with Mg in excess of the 4% dissolved in the matrix. By combining these results

  14. Thermo-kinetic mechanisms for grain boundary structure multiplicity, thermal instability and defect interactions

    Energy Technology Data Exchange (ETDEWEB)

    Burbery, N.J. [Department of Mechanical Engineering, University of Auckland, Auckland 1010 (New Zealand); Das, R., E-mail: r.das@auckland.ac.nz [Department of Mechanical Engineering, University of Auckland, Auckland 1010 (New Zealand); Ferguson, W.G. [Department of Chemical and Materials Engineering, University of Auckland, Auckland 1010 (New Zealand)

    2016-08-15

    Grain boundaries (GBs) provide a source and/or a sink for crystal defects and store elastic energy due to the non-uniform atomic bonding structure of the GB core. GB structures are thermodynamically driven to transition to the lowest energy configuration possible; however to date there has been little evidence to explain why specific GB structures have a low energy state. Furthermore, there is little quantitative demonstration of the significance of physical and GB structure characteristics on the GB energy, thermal stability, and the effect of temporary local GB structure transformations on defect interactions. This paper evaluates the defect interactions and structure stability of multiple Σ5(310) GB structures in bi-crystals of pure aluminium, and systematically investigates the features at 0 K to characterise multiple metastable structures. Structure stability is evaluated by utilising unstable vacancy defects to initiate GB transformations, and using nudged elastic band simulations to quantify this with the activation energy. The emission of stable vacancy defects from the ‘stable’ and metastable grain boundaries is also evaluated in the same manner. A detailed analysis of dislocation nucleation at the atomistic scale demonstrates that local transformations of GB structure between stable and metastable intermediates can provide a mechanism to accommodate the generation of crystal defects. Kinetic (time-dependent) effects that compete with energetic driving forces for structural transformations of GBs are shown to cause a significant effect on the activation properties that may exceed the influence of GB potential energy. The results demonstrate that GB structural multiplicity can be associated with the generation and absorption of dislocations and vacancies. This paper demonstrates the suitability of atomistic simulations coupled with nudged elastic band simulations to evaluate fundamental thermodynamic properties of pure FCC metals. Overall, this paper

  15. Secondary recrystallization in non-sag W filament wires -- On the possible role of relative grain boundary character distribution

    International Nuclear Information System (INIS)

    Samajdar, I.; Watte, P.; Mertens, F.

    1999-01-01

    Non-Sag tungsten (W) wire is indispensable for the lighting industry. For the necessary creep resistance, large elongated grains are considered as the desired microstructure. These large grains are obtained by primary and secondary recrystallization. In the present study an effort has been made to characterize and to understand the origin of such large elongated grains. In secondary recrystallization, often called abnormal grain growth, a few of the grains grow massive. The mechanisms of normal and abnormal grain growth are essentially the same, involving high angle boundary migration and driven by the reduction of surface energy. The abnormal grain growth can be visualized as a growth advantage for a few of the grains or growth disadvantage for the majority. Such an advantage/disadvantage may be caused by (1) differences in grain size and/or (2) differences in grain boundary character distribution (GBCD). In other words, a grain may grow massive if it has large size and/or possibilities of more favorable (i.e., of higher mobility) grain boundaries with the matrix grains

  16. Computer generated structures of grain boundaries in Li2-type ordered alloys

    International Nuclear Information System (INIS)

    DeHosson, J.Th.M.; Pestman, B.J.; Schapink, F.W.; Tichelaar, F.D.

    1988-01-01

    In recent years, the influence of the establishment of long-range order in cubic alloys on the structure of grain boundaries in Li 2 alloys has been considered. Thus, for example, for the Σ = 5 (310) tilt boundary the various possible structures have been investigated that are generated upon ordering, starting from plausible structures in the disordered state. However, apart from some rough energy estimates based upon nearest neighbor interactions, no reliable energy calculations have been performed of these different possible structures. In this paper, computer calculations based upon interatomic pair potentials constructed in such a way that the Li 2 structure is stable with respect to disordering, are reported for the Σ = 5 (310) boundary. The relative stability of various possible structures, with associated different boundary compositions, has been investigated

  17. A Study of diffusion and grain boundaries in ionic compounds by the molecular dynamic method

    International Nuclear Information System (INIS)

    Karakasidis, Theodoros

    1995-01-01

    In the first part, we present a model of variable cationic charges based on a rigid ion potential. In order to implement the model we performed static and dynamic simulations in calcium fluoride. The structural properties do not depend on the way the model is adjusted but the anion diffusion and the high frequency dielectric constant do. These results allowed to specify the criteria to adjust the variable charge model. As indicated by the behaviour of optical phonons this model introduced a supplementary polarisation mechanism to the rigid ion model. In the second part of this work, we studied the structural and diffusional behaviour of a high angle tilt grain boundary in NiO by molecular dynamics, using a usual rigid ion model. We examined structures with and without point defects between 0 K and 2500 K. The structure without defects presents always the lowest potential energy. In the others structures the defects can cluster and sometimes cause local changes in the boundary. Computer simulated images of high resolution electron microscopy, produced using these structures, present a similarity with the experimental ones. We calculated in the same boundary the diffusion coefficient of a doubly charged nickel vacancy between 2250 K and 2650 K. The atomic trajectories reveal the existence of preferential migration paths for the vacancy. The grain boundary diffusion is slightly anisotropic which is in agreement with an extrapolation of experimental results. A similar study in the volume reveals a migration energy higher than in the grain boundary. The calculated quantities allow for an estimation of the nickel diffusion acceleration due to the boundary. This acceleration is significant, but lower than the one measured by certain authors in polycrystalline, NiO; other authors studying bicrystals have not observed any acceleration. (author) [fr

  18. Grain boundary migration induced segregation in V-Cr-Ti alloys

    Energy Technology Data Exchange (ETDEWEB)

    Gelles, D.S. [Pacific Northwest National Lab., Richland, WA (United States); Ohnuki, S.; Takahashi, H. [Univ. of Hokkaido (Japan)

    1996-10-01

    Analytical electron microscopy results are reported for a series of vanadium alloys irradiated in the HFIR JP23 experiment at 500{degrees}C. Alloys were V-5Cr-5Ti and pure vanadium which are expected to have transmuted to V-15Cr-5Ti and V-10Cr following irradiation. Analytical microscopy confirmed the expected transmutation occurred and showed redistribution of Cr and Ti resulting from grain boundary migration in V-5Cr-5Ti, but in pure V, segregation was reduced and no clear trends as a function of position near a boundary were identified.

  19. Ultra-thin grain-oriented silicon steel sheet fabricated by a novel way: Twin-roll strip casting and two-stage cold rolling

    Science.gov (United States)

    Wang, Yin-Ping; Liu, Hai-Tao; Song, Hong-Yu; Liu, Jia-Xin; Shen, Hui-Ying; Jin, Yang; Wang, Guo-Dong

    2018-04-01

    0.05-0.15 mm-thick ultra-thin grain-oriented silicon steel sheets were successfully produced by a novel processing route including strip casting, hot rolling, normalizing, two-stage cold rolling with intermediate annealing, primary recrystallization annealing and secondary recrystallization annealing. The evolutions of microstructure, texture and inhibitor along the processing were briefly investigated. The results showed that the initial Goss orientation originated due to the heterogenous nucleation of δ-ferrite grains during solidification. Because of the lack of shear deformation, only a few Goss grains were observed in the hot rolled sheet. After the first cold rolling and intermediate annealing, Goss texture was enhanced and distributed in the whole thickness. A small number of Goss grains having a high fraction of high energy boundaries exhibited in the primary recrystallization annealed sheet. A large number of fine and dispersed MnS and AlN and a few co-precipitates MnS and AlN with the size range of 10-70 nm were also observed. Interestingly, a well-developed secondary recrystallization microstructure characterized by 10-60 mm grains and a sharp Goss texture were finally produced in the 0.05-0.15 mm-thick ultra-thin sheets. A magnetic induction B8 of 1.72-1.84 T was obtained. Another new finding was that a few {2 3 0}〈0 0 1〉 and {2 1 0}〈1 2 7〉 grains also can grow up abnormally because of the high fraction of high energy boundaries and the size and number advantage, respectively. These non-Goss grains finally deteriorated the magnetic properties of the ultra-thin sheets. In addition, low surface energies of {hk0} planes may also contribute to the abnormal growth of Goss, {2 3 0}〈0 0 1〉 and {2 1 0}〈1 2 7〉 grains.

  20. Dissolution of kinetics of nanoscale liquid Pb/Bi inclusions at a grain boundary in aluminium

    DEFF Research Database (Denmark)

    Prokofjev, Sergei I.; Johnson, Erik; Zhilin, Victor M.

    2008-01-01

    of the inclusions was observed until their complete disappearance. Digitized video recordings of the process of dissolution were used to obtain the dependence of the inclusion size with time. The kinetics of the dissolution of the grain boundary inclusions can be described with a model where it is assumed......In situ transmission selctron microscopy is used to study dissolution of liquid single-phase Pb/Bi inclusions attached to grain boundary in an alloy of Al99.29Pb0.65Bi0.06 at temperatures of 343, 370, and 389 °C, respectively.  The initial size of the inclusions was smaller than 60 nm.  Dissolution...

  1. Formation of Cavities at and Away from Grain Boundaries during 600 MeV Proton Irradiation

    DEFF Research Database (Denmark)

    Singh, Bachu Narain; Leffers, Torben; Green, W. V.

    1982-01-01

    ) regions beyond the CCZ containing a very low density of cavities. At the dose level of 2 dpa, a dense population of very small cavities is resolved on the grain boundaries and also in their immediate vicinity (in the CDZ). Furthermore, at the dose levels of 0.6 and 2 dpa, a well defined dual size...... were carried out at 120 degree C (0,42*Tm where Tm is the melting temperature in K). Transmission electron microscopy on specimens irradiated to 0.2 and 0.6 dpa has shown the presence of (a) cavity-denuded zones (CDZ) along grain boundaries, (b) cavity-containing zones (CCZ) adjacent to the CDZ and (c...... distribution of cavities is observed in the CCZ. The results are discussed in terms of agglomeration of helium atoms which are considered, during irradiation, to diffuse mainly via vacancies....

  2. The potential role of diffusion-induced grain-boundary migration in extended life prediction

    International Nuclear Information System (INIS)

    Handwerker, C.A.; Blendell, J.E.; Interrante, C.G.; Ahn, T.M.

    1993-01-01

    The selection of materials that are suitable for various high-level waste-packaging designs must reflect the need to meet requirements for long-term performance in repository environments that change with time. With this in mind, we examine how grain boundaries in materials are induced to migrate as a result of solute diffusion even at low temperatures, how the composition of the matrix material is changed significantly by this diffusion-induced grain boundary migration (DIGM), and how the changing microstructures and compositions during DIGM lead to major changes in materials performance, such as corrosion or embrittlement. Methods are discussed for prediction of the long-term behavior of materials affected by DIGM

  3. Surface studies of iridium-alloy grain boundaries associated with weld cracking

    International Nuclear Information System (INIS)

    Mosley, W.C.

    1982-01-01

    Plutonium-238 oxide fuel pellets for the General Purpose Heat Source (GPHS) Radioisotopic Thermoelectric Generators to be used on the NASA Galileo Mission to Jupiter and the International Solar Polar Mission are produced and encapsulated in iridium alloy at the Savannah River Plant (SRP). Underbead cracks occasionally occur in the girth weld on the iridium-alloy-clad vent sets in the region where the gas tungsten arc is quenched. Grain-boundary structures and compositions were characterized by scanning electron microscopy/x-ray energy spectroscopy, electron microprobe analysis and scanning Auger microprobe analysis to determine the cause of weld quench area cracking. Results suggest that weld quench area cracking may be caused by gas porosity or liquation in the grain boundaries

  4. Simulation of He embrittlement at grain boundaries in bcc transition metals

    International Nuclear Information System (INIS)

    Suzudo, Tomoaki; Yamaguchi, Masatake

    2015-01-01

    To investigate what atomic properties largely determine vulnerability to He embrittlement at grain boundaries (GB) of bcc metals, we introduce a computational model composed of first principles density functional theory and a He segregation rate theory model. Predictive calculations of He embrittlement at the first wall of the future DEMO fusion concept reactor indicate that variation in the He embrittlement originated not only from He production rate related to neutron irradiation, but also from the He segregation energy at the GB that has a systematic trend in the periodic table. - Highlights: • We modeled He grain boundary (GB) segregation of bcc transition metals using first-principles-based rate theory. • We established the quantitative relation between He embrittlement and He segregation using GB cohesive energy. • He embrittlement was strongly dependent on He segregation energy at the GB that has a systematic trend in the periodic table.

  5. Brittle-to-ductile transition in polycrystalline aluminum containing gallium in the grain boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Itoh, A; Izumi, J; Ina, K; Koizumi, H, E-mail: koizumi@isc.meiji.ac.j [Deaprtment of Physics, Meiji University, Higashi-mita, Tama-ku, Kawasaki, 214-8571 (Japan)

    2010-07-01

    It is well known that aluminum/gallium couple causes liquid metal embrittlement. Gallium atoms penetrate the grain boundaries of polycrystalline aluminum and degrade it. Polycrystalline aluminum specimens were contacted with a small droplet of gallium for 24 h. After gallium was removed from the surface of the specimens, tensile tests were performed between 77 K and 313 K. The specimens are ductile below 230 K and brittle above 303 K, the melting temperature of gallium. Between 280 K and 300 K, the maximum stress is larger in the specimens heated from 77 K than in those cooled from 313 K. This thermal history dependence of the maximum stress is considered to be attributed to the solidification of supercooled gallium in the grain boundaries.

  6. ROLE OF GRAIN BOUNDARY CARBIDES IN CRACKING BEHAVIOR OF Ni BASE ALLOYS

    Directory of Open Access Journals (Sweden)

    SEONG SIK HWANG

    2013-02-01

    Full Text Available The primary water stress corrosion cracking (PWSCC of Alloy 600 in a PWR has been reported in the control rod drive mechanism (CRDM, pressurizer instrumentation, and the pressurizer heater sleeves. Recently, two cases of boric acid precipitation that indicated leaking of the primary cooling water were reported on the bottom head surface of steam generators (SG in Korea. The PWSCC resistance of Ni base alloys which have intergranular carbides is higher than those which have intragranular carbides. Conversely, in oxidized acidic solutions like sodium sulfate or sodium tetrathionate solutions, the Ni base alloys with a lot of carbides at the grain boundaries and shows less stress corrosion cracking (SCC resistance. The role of grain boundary carbides in SCC behavior of Ni base alloys was evaluated and effect of intergranular carbides on the SCC susceptibility were reviewed from the literature.

  7. Grain boundary chromium concentration effects on the IGSCC and IASCC of austenitic stainless steels

    International Nuclear Information System (INIS)

    Bruemmer, S.M.; Arey, B.W.; Charlot, L.A.

    1993-08-01

    Comparisons are made between grain boundary composition and intergranular stress corrosion cracking (IGSCC) of 304 and 309 austenitic stainless steels in high-temperature water environments. Chromium depletion had the dominant effect on cracking resistance with the extent of IG cracking controlled by the interfacial chromium concentration. The minimum chromium concentration required to promote cracking was a function of the applied strain rate during slow-strain-rate tensile tests in 288 C air-saturated water. Depletion from bulk levels of 18 wt% to ∼13.5 wt% Cr at grain boundaries prompted 100% IG cracking at a strain rate of 1 x 10 -6 s -1 , while embrittlement was observed with only a slight depletion to ∼17 wt% at 2 x 10 -7 s -1 . Insights into critical interfacial compositions promoting IGSCC are discussed in reference to cracking of irradiated stainless steel nuclear reactor core components

  8. Fundamental Studies of the Role of Grain Boundaries on Uniform Corrosion of Advanced Nuclear Reactor Materials

    International Nuclear Information System (INIS)

    Taheri, Mitra; Motta, Arthur; Marquis, Emmanuelle

    2016-01-01

    The main objective of this proposal is to develop fundamental understanding of the role of grain boundaries in stable oxide growth. To understand the process of oxide layer destabilization, it is necessary to observe the early stages of corrosion. During conventional studies in which a sample is exposed and examined after removal from the autoclave, the destabilization process will normally have already taken place, and is only examined post facto. To capture the instants of oxide destabilization, it is necessary to observe it in situ; however, significant questions always arise as to the influence of the corrosion geometry and conditions on the corrosion process. Thus, a combination of post facto examinations and in situ studies is proposed, which also combines state-of-the-art characterization techniques to derive a complete understanding of the destabilization process and the role of grain boundaries.

  9. Fundamental Studies of the Role of Grain Boundaries on Uniform Corrosion of Advanced Nuclear Reactor Materials

    Energy Technology Data Exchange (ETDEWEB)

    Taheri, Mitra [Drexel Univ., Philadelphia, PA (United States); Motta, Arthur [Pennsylvania State Univ., University Park, PA (United States); Marquis, Emmanuelle [Univ. of Michigan, Ann Arbor, MI (United States)

    2016-05-20

    The main objective of this proposal is to develop fundamental understanding of the role of grain boundaries in stable oxide growth. To understand the process of oxide layer destabilization, it is necessary to observe the early stages of corrosion. During conventional studies in which a sample is exposed and examined after removal from the autoclave, the destabilization process will normally have already taken place, and is only examined post facto. To capture the instants of oxide destabilization, it is necessary to observe it in situ; however, significant questions always arise as to the influence of the corrosion geometry and conditions on the corrosion process. Thus, a combination of post facto examinations and in situ studies is proposed, which also combines state-of-the-art characterization techniques to derive a complete understanding of the destabilization process and the role of grain boundaries.

  10. First combined electron backscatter diffraction and transmission electron microscopy study of grain boundary structure of deformed quartzite.

    Science.gov (United States)

    Shigematsu, N; Prior, D J; Wheeler, J

    2006-12-01

    The structures of boundaries in a deformed and dynamically recovered and recrystallized quartz polycrystal (mylonite) were characterized by transmission electron microscopy, after the misorientation angles across the same grain boundaries had been analysed using electron backscatter diffraction in a scanning electron microscope. In this new approach, a specific sample area is mapped with electron backscatter diffraction, and the mapped area is then attached to a foil, and by the ion beam thinned for transmission electron microscopy analysis. Dislocations in grain boundaries were recognized as periodic and parallel fringes. The fringes associated with dislocations are observed in boundaries with misorientations less than 9 degrees , whereas such fringes cannot be seen in the boundaries with misorientations larger than 17 degrees . Some boundaries with misorientations between 9 degrees and 17 degrees generally have no structures associated with dislocation. One segment of a boundary with a misorientation of 13.5 degrees has structures associated with dislocations. It is likely that the transition from low-angle to high-angle boundaries occurs at misorientations ranging from approximately 9 degrees to 14 degrees . Change in the grain boundary structure presumably influences the mobility of the boundaries. In the studied deformed quartz vein, a relative dearth of boundaries between misorientation angles of theta = 2 degrees and theta = 15 degrees has previously been reported, and high-angle boundaries form cusps where they intersect low-angle boundaries, suggesting substantial mobility of high-angle boundaries.

  11. Influence of nano-inclusions' grain boundaries on crack propagation modes in materials

    International Nuclear Information System (INIS)

    Karakasidis, T.E.; Charitidis, C.A.

    2011-01-01

    The effect of nano-inclusions on materials' strength and toughness has attracted great interest in recent years. It has been shown that tuning the morphological and microstructural features of materials can tailor their fracture modes. The existence of a characteristic size of inclusions that favours the fracture mode (i.e. transgranular or intergranular) has been experimentally observed but also predicted by a 2D model based on energetic arguments which relates the crack propagation mode to the ratio of the interface area between the crystalline inclusion and the matrix with the area of the crystallite inclusion in a previous work. In the present work, a 3D model is proposed in order to extend the 2D model and take into account the influence of the size of grain boundary zone on the toughening/hardening behavior of the material as it was observed experimentally in the literature. The model relates crack propagation mode to the ratio of the volume of the grain boundary zone between the crystalline inclusion and the matrix with the volume of the nano-inclusion. For a ratio below a critical value, transgranular propagation is favoured while for larger values, intergranular propagation is favoured. We also demonstrate that the extent of the grain boundary region also can significantly affect this critical value. The results of the model are in agreement with the literature experimental observations related to the toughening/hardening behavior as a function of the size of crystalline inclusions as well as the width of the grain boundary regions.

  12. Self-generated magnetic flux in YBa$_2$Cu$_3$O$_{7-x}$ grain boundaries

    OpenAIRE

    Mints, R. G.; Papiashvili, Ilya

    2000-01-01

    Grain boundaries in YBa$_2$Cu$_3$O$_{7-x}$ superconducting films are considered as Josephson junctions with a critical current density $j_c(x)$ alternating along the junction. A self-generated magnetic flux is treated both analytically and numerically for an almost periodic distribution of $j_c(x)$. We obtained a magnetic flux-pattern similar to the one which was recently observed experimentally.

  13. Dynamic recrystallization and grain boundary migration in B2 FeAl

    Science.gov (United States)

    Baker, I.; Gaydosh, D. J.

    1987-01-01

    Transmission electron microscopy and optical microscopy were used to examine polycrystalline specimens of the B2-structured alloy FeAl strained under tension to fracture at elevated temperature. Strain-induced grain boundary migration was observed above 900 K and dynamic recrystallization was found at 1000 K and 1100 K. Little evidence of dynamic recovery was evident but some networks were formed at 1100 K.

  14. Influence of nano-inclusions' grain boundaries on crack propagation modes in materials

    Energy Technology Data Exchange (ETDEWEB)

    Karakasidis, T.E., E-mail: thkarak@uth.gr [Department of Civil Engineering, University of Thessaly, Pedion Areos, 38834 Volos (Greece); Charitidis, C.A. [National Technical University of Athens, School of Chemical Engineering, 9 Heroon Polytechniou st., Zografos, 157 80 Athens (Greece)

    2011-04-15

    The effect of nano-inclusions on materials' strength and toughness has attracted great interest in recent years. It has been shown that tuning the morphological and microstructural features of materials can tailor their fracture modes. The existence of a characteristic size of inclusions that favours the fracture mode (i.e. transgranular or intergranular) has been experimentally observed but also predicted by a 2D model based on energetic arguments which relates the crack propagation mode to the ratio of the interface area between the crystalline inclusion and the matrix with the area of the crystallite inclusion in a previous work. In the present work, a 3D model is proposed in order to extend the 2D model and take into account the influence of the size of grain boundary zone on the toughening/hardening behavior of the material as it was observed experimentally in the literature. The model relates crack propagation mode to the ratio of the volume of the grain boundary zone between the crystalline inclusion and the matrix with the volume of the nano-inclusion. For a ratio below a critical value, transgranular propagation is favoured while for larger values, intergranular propagation is favoured. We also demonstrate that the extent of the grain boundary region also can significantly affect this critical value. The results of the model are in agreement with the literature experimental observations related to the toughening/hardening behavior as a function of the size of crystalline inclusions as well as the width of the grain boundary regions.

  15. Observation of Pseudopartial Grain Boundary Wetting in the NdFeB-Based Alloy

    Science.gov (United States)

    Straumal, B. B.; Mazilkin, A. A.; Protasova, S. G.; Schütz, G.; Straumal, A. B.; Baretzky, B.

    2016-08-01

    The NdFeB-based alloys were invented in 1980s and remain the best-known hard magnetic alloys. In order to reach the optimum magnetic properties, the grains of hard magnetic Nd2Fe14B phase have to be isolated from one another by the (possibly thin) layers of a non-ferromagnetic Nd-rich phase. In this work, we observe that the few-nanometer-thin layers of the Nd-rich phase appear between Nd2Fe14B grains due to the pseudopartial grain boundary (GB) wetting. Namely, some Nd2Fe14B/Nd2Fe14B GBs are not completely wetted by the Nd-rich melt and have the high contact angle with the liquid phase and, nevertheless, contain the 2-4-nm-thin uniform Nd-rich layer.

  16. Simulation of the effects of grain boundary fission gas during thermal transients

    International Nuclear Information System (INIS)

    Fenske, G.R.; Emerson, J.E.; Beiersdorf, B.A.

    1984-11-01

    This report presents the results of an initial set of out-of-cell transient heating experiments performed on unirradiated UO 2 pellets fabricated to simulate the effect of grain boundary fission gas on fuel swelling and cladding failure. The fabrication involved trapping high-pressure argon on internal pores by sintering annular UO 2 pellets in a hot isostatic press (HIP). The pellet stack was subjected to two separate transients (DGF83-03A and -03B). Figures show photomicrographs of HIPped and non-HIPped UO 2 , respectively, and the adjacent cladding after DGF83-03B. Fuel melting occurred at the center of both the HIPped and non-HIPped pellets; however, a dark ring is present near the center in the HIPped fuel but not in the non-HIPped fuel. This dark band is a high-porosity region due to increased grain boundary/edge swelling in that pellet. In contrast, grain boundary/edge swelling did not occur in the non-HIPped pellets. Thus, the presence of the high-pressure argon trapped on internal pores during sintering in the HIP altered the microstructural behavior. Results of these preliminary tests indicate that the microstructural behavior of HIPped fuel during thermal transients is different from the behavior of conventionally fabricated fuel

  17. Silicon improves rice grain yield and photosynthesis specifically when supplied during the reproductive growth stage.

    Science.gov (United States)

    Lavinsky, Alyne O; Detmann, Kelly C; Reis, Josimar V; Ávila, Rodrigo T; Sanglard, Matheus L; Pereira, Lucas F; Sanglard, Lílian M V P; Rodrigues, Fabrício A; Araújo, Wagner L; DaMatta, Fábio M

    2016-11-01

    Silicon (Si) has been recognized as a beneficial element to improve rice (Oryza sativa L.) grain yield. Despite some evidence suggesting that this positive effect is observed when Si is supplied along the reproductive growth stage (from panicle initiation to heading), it remains unclear whether its supplementation during distinct growth phases can differentially impact physiological aspects of rice and its yield and the underlying mechanisms. Here, we investigated the effects of additions/removals of Si at different growth stages and their impacts on rice yield components, photosynthetic performance, and expression of genes (Lsi1, Lsi2 and Lsi6) involved in Si distribution within rice shoots. Positive effects of Si on rice production and photosynthesis were manifested when it was specifically supplied during the reproductive growth stage, as demonstrated by: (1) a high crop yield associated with higher grain number and higher 1000-grain weight, whereas the leaf area and whole-plant biomass remained unchanged; (2) an increased sink strength which, in turn, exerted a feed-forward effect on photosynthesis that was coupled with increases in both stomatal conductance and biochemical capacity to fix CO 2 ; (3) higher Si amounts in the developing panicles (and grain husks) in good agreement with a remarkable up-regulation of Lsi6 (and to a lesser extent Lsi1). We suggest that proper levels of Si in these reproductive structures seem to play an as yet unidentified role culminating with higher grain number and size. Copyright © 2016 Elsevier GmbH. All rights reserved.

  18. The discovery of silicon oxide nanoparticles in space-weathered of Apollo 15 lunar soil grains

    Science.gov (United States)

    Gu, Lixin; Zhang, Bin; Hu, Sen; Noguchi, Takaaki; Hidaka, Hiroshi; Lin, Yangting

    2018-03-01

    Space weathering is an important process on the Moon and other airless celestial bodies. The most common space weathering effects are amorphization of the top surface of soil grains and formation of nanophase iron particles (npFe) within the partially amorphous rims. Hence, space weathering significantly affects optical properties of the surface of the Moon and other airless celestial bodies. Transmission electron microscope (TEM) analysis of Apollo 15 soil grains displays npFe (≤5 nm in size) embedded in the space-weathered rim (∼60 nm in thickness) of a pyroxene grain, consistent with previous studies. In contrast, submicron-sized fragments that adhere to the pyroxene grain show distinct space weathering features. Silicon oxide nanoparticles (npSiOx) were observed with npFe in a submicron-sized Mg-Fe silicate fragment. This is the first discovery of npSiOx as a product of space weathering. The npSiOx and the coexisting npFe are ∼10-25 nm in size, significantly larger than the typical npFe in the space weathered rim of the pyroxene grain. The coexisting npSiOx and npFe were probably formed directly in micrometeorite shock-induced melt, instead of in a solar-wind generated vapor deposit or irradiated rim. This new observation will shed light on space weathering processes on the Moon and airless celestial bodies.

  19. Non-equilibrium grain boundaries in titanium nanostructured by severe plastic deformation: Computational study of sources of material strengthening

    DEFF Research Database (Denmark)

    Liu, Hongsheng; Mishnaevsky, Leon; Pantleon, Wolfgang

    2014-01-01

    and properties of the grain boundary (GB) phase have been carried out. The effect of different degrees of deviation from the equilibrium state of the grain boundaries (GBs) on the mechanical behaviour of nanostructured Ti have been investigated using the combined composite/dislocation dynamics based model....... In particular, the effects of different diffusion coefficients in the GB phase, of a high initial dislocation density in the grain boundaries, as well as of atomic scale precipitates are investigated for affecting the deformation behaviour of UFG or nanostructured Ti. © 2013 Elsevier B.V. All rights reserved....

  20. Intrinsic Compressive Stress in Polycrystalline Films is Localized at Edges of the Grain Boundaries

    Science.gov (United States)

    Vasco, Enrique; Polop, Celia

    2017-12-01

    The intrinsic compression that arises in polycrystalline thin films under high atomic mobility conditions has been attributed to the insertion or trapping of adatoms inside grain boundaries. This compression is a consequence of the stress field resulting from imperfections in the solid and causes the thermomechanical fatigue that is estimated to be responsible for 90% of mechanical failures in current devices. We directly measure the local distribution of residual intrinsic stress in polycrystalline thin films on nanometer scales, using a pioneering method based on atomic force microscopy. Our results demonstrate that, at odds with expectations, compression is not generated inside grain boundaries but at the edges of gaps where the boundaries intercept the surface. We describe a model wherein this compressive stress is caused by Mullins-type surface diffusion towards the boundaries, generating a kinetic surface profile different from the mechanical equilibrium profile by the Laplace-Young equation. Where the curvatures of both profiles differ, an intrinsic stress is generated in the form of Laplace pressure. The Srolovitz-type surface diffusion that results from the stress counters the Mullins-type diffusion and stabilizes the kinetic surface profile, giving rise to a steady compression regime. The proposed mechanism of competition between surface diffusions would explain the flux and time dependency of compressive stress in polycrystalline thin films.

  1. Multiscale Modeling of Grain Boundaries in ZrB2: Structure, Energetics, and Thermal Resistance

    Science.gov (United States)

    Lawson, John W.; Daw, Murray S.; Squire, Thomas H.; Bauschlicher, Charles W., Jr.

    2012-01-01

    A combination of ab initio, atomistic and finite element methods (FEM) were used to investigate the structures, energetics and lattice thermal conductance of grain boundaries for the ultra high temperature ceramic ZrB2. Atomic models of idealized boundaries were relaxed using density functional theory. Information about bonding across the interfaces was determined from the electron localization function. The Kapitza conductance of larger scale versions of the boundary models were computed using non-equilibrium molecular dynamics. The interfacial thermal parameters together with single crystal thermal conductivities were used as parameters in microstructural computations. FEM meshes were constructed on top of microstructural images. From these computations, the effective thermal conductivity of the polycrystalline structure was determined.

  2. Electron scattering at surfaces and grain boundaries in Cu thin films and wires

    Science.gov (United States)

    Chawla, J. S.; Gstrein, F.; O'Brien, K. P.; Clarke, J. S.; Gall, D.

    2011-12-01

    The electron scattering at surfaces, interfaces, and grain boundaries is investigated using polycrystalline and single-crystal Cu thin films and nanowires. The experimental data is described by a Fuchs-Sondheimer (FS) and Mayadas-Shatzkes (MS) model that is extended to account for the large variation in the specific resistivity of different grain boundaries as well as distinct top and bottom surfaces with different scattering specularity p. Textured polycrystalline Cu(111) thin films with thickness d = 25-50 nm are deposited on a stack of 7.5-nm Ta on SiO2/Si(001). Subsequent annealing results in small-grain (SG) thin films with an average grain size D¯ that increases from 90 to 120 nm with increasing d. Corresponding large-grain (LG) thin films with D¯ = 160-220 nm are obtained by depositing 100-200-nm-thick films, followed by an in-situ anneal and a subsequent etch to match the thickness of the SG samples. Nanowires are fabricated from the SG and LG thin films using a subtractive patterning process, yielding wire widths of 75-350 nm. Single-crystal and LG layers exhibit a 18-22% and 10-15% lower resistivity than SG layers, respectively. The resistivity decrease from SG to LG Cu nanowires is 7-9%. The thickness and grain size dependence of the resistivity of polycrystalline and single-crystal Cu layers is well described by an exact version of the existing FS + MS model but is distinct from the commonly used approximation, which introduces an error that increases with decreasing layer thickness from 6.5% for d = 50 nm to 17% for d = 20 nm. The case of nanowires requires the FS + MS model to be extended to account for variation in the grain boundary reflection coefficient R, which effectively increases the overall resistivity by, for example, 16% for 50 × 45 nm2 wires. The overall data from single and polycrystalline Cu layers and wires yields R = 0.25 ± 0.05, and p = 0 at Cu-air and Cu-Ta interfaces.

  3. Characterization and Modeling of Grain Boundary Chemistry Evolution in Ferritic Steels under Irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Marquis, Emmanuelle [Univ. of Michigan, Ann Arbor, MI (United States); Wirth, Brian [Univ. of Tennessee, Knoxville, TN (United States); Was, Gary [Univ. of Michigan, Ann Arbor, MI (United States)

    2016-03-28

    Ferritic/martensitic (FM) steels such as HT-9, T-91 and NF12 with chromium concentrations in the range of 9-12 at.% Cr and high Cr ferritic steels (oxide dispersion strengthened steels with 12-18% Cr) are receiving increasing attention for advanced nuclear applications, e.g. cladding and duct materials for sodium fast reactors, pressure vessels in Generation IV reactors and first wall structures in fusion reactors, thanks to their advantages over austenitic alloys. Predicting the behavior of these alloys under radiation is an essential step towards the use of these alloys. Several radiation-induced phenomena need to be taken into account, including phase separation, solute clustering, and radiation-induced segregation or depletion (RIS) to point defect sinks. RIS at grain boundaries has raised significant interest because of its role in irradiation assisted stress corrosion cracking (IASCC) and corrosion of structural materials. Numerous observations of RIS have been reported on austenitic stainless steels where it is generally found that Cr depletes at grain boundaries, consistently with Cr atoms being oversized in the fcc Fe matrix. While FM and ferritic steels are also subject to RIS at grain boundaries, unlike austenitic steels, the behavior of Cr is less clear with significant scatter and no clear dependency on irradiation condition or alloy type. In addition to the lack of conclusive experimental evidence regarding RIS in F-M alloys, there have been relatively few efforts at modeling RIS behavior in these alloys. The need for predictability of materials behavior and mitigation routes for IASCC requires elucidating the origin of the variable Cr behavior. A systematic detailed high-resolution structural and chemical characterization approach was applied to ion-implanted and neutron-irradiated model Fe-Cr alloys containing from 3 to 18 at.% Cr. Atom probe tomography analyses of the microstructures revealed slight Cr clustering and segregation to dislocations and

  4. Grain boundary structures in La2/3Ca1/3MnO3 thin films

    International Nuclear Information System (INIS)

    Miller, D. J.; Lin, Y.-K.; Vlasko-Vlasov, V.; Welp, U.

    1999-01-01

    As with many other oxide-based compounds that exhibit electronic behavior, structural defects have a strong influence on the electronic properties of the CMR manganites. In this work, the authors have studied the effect of grain boundaries on the transport properties and on the local orientation of magnetization. Thin films of the perovskite-related La 2/3 Ca 1/3 MnO 3 compound were deposited onto bicrystal substrates using pulsed laser deposition. Transport measurements showed some enhancement of magnetoresistance across the grain boundary. The structure of the boundary was evaluated by electron microscopy. In contrast with the highly meandering boundaries typically observed in bicrystals of high temperature superconductors, the boundaries in these films are relatively straight and well defined. However, magneto-optical imaging showed that the local magnetization was oriented out of the plane at the grain boundary while it was oriented within the plane in the grains on either side. This coordinated reorientation of local magnetization near the grain boundary leads to enhanced magnetoresistance across the boundary in low fields

  5. Molecular Dynamics Simulation of Coarse-Grain Model of Silicon Functionalized Graphene

    Directory of Open Access Journals (Sweden)

    Hui Zhixin

    2015-01-01

    Full Text Available The electronic transport, the storage capacity and the service life of the anode material for lithium ion batteries will be reduced seriously in the event of the material layering or cracking, so the anode material must have strong mechanical reliability. Firstly, in view of the traditional molecular dynamics (MD limited by the geometric scales of the model of Silicon functionalized graphenen (SFG as lithium ion batteries anode material, some full atomic models of SFG were established using Tersoff potential and Lennard-Jones potential, and used to calculate the modulus and the adhesion properties. What’s more, the assertion of mechanical equilibrium condition and energy conservation between full atomic and coarse-grain models through elastic strain energy were enforced to arrive at model parameters. The model of SFG coarse-grain bead-spring elements and its system energy function were obtained via full atomic simulations. Finally, the validity of the SFG coarse-grain model was verified by comparing the tensile property of coarse-grain model with full atoms model.

  6. Micromagnetic simulation of the orientation dependence of grain boundary properties on the coercivity of Nd-Fe-B sintered magnets

    Directory of Open Access Journals (Sweden)

    Jun Fujisaki

    2016-05-01

    Full Text Available This paper is focused on the micromagnetic simulation study about the orientation dependence of grain boundary properties on the coercivity of polycrystalline Nd-Fe-B sintered magnets. A multigrain object with a large number of meshes is introduced to analyze such anisotropic grain boundaries and the simulation is performed by combining the finite element method and the parallel computing. When the grain boundary phase parallel to the c-plane is less ferromagnetic the process of the magnetization reversal changes and the coercivity of the multigrain object increases. The simulations with various magnetic properties of the grain boundary phases are executed to search for the way to enhance the coercivity of polycrystalline Nd-Fe-B sintered magnets.

  7. Comparison of the intergranular segregation for eight dilute binary metallic systems in the Σ11 {332} tilg grain boundary

    Czech Academy of Sciences Publication Activity Database

    Duparc, O. H.; Larere, A.; Lezzar, B.; Khalfallah, O.; Paidar, Václav

    2005-01-01

    Roč. 40, - (2005), s. 3169-3176 ISSN 0022-2461 Institutional research plan: CEZ:AV0Z10100520 Keywords : grain boundary * nickel Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.901, year: 2005

  8. Evolution of grain boundary conduction with increasing temperature in pure and Ti doped Co ferrite materials

    Science.gov (United States)

    Vaithyanathan, V.; Patro, L. N.; Kodam, Ugendar; Tan, H.; Inbanathan, S. S. R.; Kamala Bharathi, K.

    2015-09-01

    We report on the structural, temperature, and frequency dependent impedance studies of Ti doped cobalt ferrite material (CoFe1.95Ti0.05O4) in comparison with the pure CoFe2O4. XRD and Raman spectroscopy studies confirm the inverse spinel crystallization of the materials with space group of Fd-3 m. Scanning electron microscope images shows the microcrystalline nature of the particles. Homogeneity, stoichiometry, and ionic states of the ions in the composition were confirmed by energy dispersive X-ray analysis and X-ray photoelectron spectroscopic studies. Temperature and frequency dependent real (Z') and imaginary (Z″) part of the impedance shows the existence of relaxation processes and their distribution in CoFe2O4 and CoFe1.95Ti0.05O4 materials. Complex impedance spectroscopy studies at low temperatures shows that the conductivity in these materials is predominantly due to the intrinsic bulk grains. With increasing the temperature, evolution of grain boundary conduction is clearly seen through the appearance of a second semi-circle in the complex impedance plots. Room temperature total dc conductivity of both CoFe2O4 and CoFe1.95Ti0.05O4 materials is found to be 5.78 × 10-8 and 1.61 × 10-7 S/cm, respectively. Temperature variation of dc electrical conductivity follows the Arrhenius relationship and the activation energies for CoFe2O4 corresponding to grain (0.55 eV for CoFe2O4), grain boundary (0.52 eV), and total conduction (0.54 eV) are discussed. Observation of well distinguishable grain and grain boundary conductions and the low conductivity values in CoFe2O4 and CoFe1.95Ti0.05O4 materials indicates that these materials are promising candidates for the high frequency applications.

  9. Evolution of grain boundary conduction with increasing temperature in pure and Ti doped Co ferrite materials

    Energy Technology Data Exchange (ETDEWEB)

    Vaithyanathan, V. [Research and Development Centre, Bharathiar University, Coimbatore-641 046 (India); Patro, L. N., E-mail: laxminar@chemie.uni-marburg.de, E-mail: kkamalabharathi@gmail.com [Department of Chemistry, Philips University of Marburg, 35032, Marburg (Germany); Kodam, Ugendar [Advanced Magnetic Materials Laboratory (AMMLa), Department of Physics, Indian Institute of Technology Madras, Chennai-600 036 (India); Tan, H. [Theiss Research, La Jolla, California 92037 (United States); Materials Measurement Laboratory, National Institute of Standards and Technology, Gaithersburg, Maryland 20899 (United States); Inbanathan, S. S. R. [Post Graduate and Research Department of Physics, The American College, Madurai-625002 (India); Kamala Bharathi, K., E-mail: laxminar@chemie.uni-marburg.de, E-mail: kkamalabharathi@gmail.com [Materials Measurement Laboratory, National Institute of Standards and Technology, Gaithersburg, Maryland 20899 (United States); Department of Materials Science and Engineering, University of Maryland, College Park, Maryland 20742 (United States)

    2015-09-21

    We report on the structural, temperature, and frequency dependent impedance studies of Ti doped cobalt ferrite material (CoFe{sub 1.95}Ti{sub 0.05}O{sub 4}) in comparison with the pure CoFe{sub 2}O{sub 4}. XRD and Raman spectroscopy studies confirm the inverse spinel crystallization of the materials with space group of Fd-3 m. Scanning electron microscope images shows the microcrystalline nature of the particles. Homogeneity, stoichiometry, and ionic states of the ions in the composition were confirmed by energy dispersive X-ray analysis and X-ray photoelectron spectroscopic studies. Temperature and frequency dependent real (Z′) and imaginary (Z″) part of the impedance shows the existence of relaxation processes and their distribution in CoFe{sub 2}O{sub 4} and CoFe{sub 1.95}Ti{sub 0.05}O{sub 4} materials. Complex impedance spectroscopy studies at low temperatures shows that the conductivity in these materials is predominantly due to the intrinsic bulk grains. With increasing the temperature, evolution of grain boundary conduction is clearly seen through the appearance of a second semi-circle in the complex impedance plots. Room temperature total dc conductivity of both CoFe{sub 2}O{sub 4} and CoFe{sub 1.95}Ti{sub 0.05}O{sub 4} materials is found to be 5.78 × 10{sup −8} and 1.61 × 10{sup −7} S/cm, respectively. Temperature variation of dc electrical conductivity follows the Arrhenius relationship and the activation energies for CoFe{sub 2}O{sub 4} corresponding to grain (0.55 eV for CoFe{sub 2}O{sub 4}), grain boundary (0.52 eV), and total conduction (0.54 eV) are discussed. Observation of well distinguishable grain and grain boundary conductions and the low conductivity values in CoFe{sub 2}O{sub 4} and CoFe{sub 1.95}Ti{sub 0.05}O{sub 4} materials indicates that these materials are promising candidates for the high frequency applications.

  10. Sensitivity analysis of Immersed Boundary Method simulations of fluid flow in dense polydisperse random grain packings

    Science.gov (United States)

    Knight, Chris; Abdol Azis, Mohd Hazmil; O'Sullivan, Catherine; van Wachem, Berend; Dini, Daniele

    2017-06-01

    Polydisperse granular materials are ubiquitous in nature and industry. Despite this, knowledge of the momentum coupling between the fluid and solid phases in dense saturated grain packings comes almost exclusively from empirical correlations [2-4, 8] with monosized media. The Immersed Boundary Method (IBM) is a Computational Fluid Dynamics (CFD) modelling technique capable of resolving pore scale fluid flow and fluid-particle interaction forces in polydisperse media at the grain scale. Validation of the IBM in the low Reynolds number, high concentration limit was performed by comparing simulations of flow through ordered arrays of spheres with the boundary integral results of Zick and Homsy [10]. Random grain packings were studied with linearly graded particle size distributions with a range of coefficient of uniformity values (Cu = 1.01, 1.50, and 2.00) at a range of concentrations (ϕ ∈ [0.396; 0.681]) in order to investigate the influence of polydispersity on drag and permeability. The sensitivity of the IBM results to the choice of radius retraction parameter [1] was investigated and a comparison was made between the predicted forces and the widely used Ergun correlation [3].

  11. Interdiffusion and grain-boundary migration in Au-Cu bilayers during ion-irradiation

    International Nuclear Information System (INIS)

    Alexander, D.E.; Rehn, L.E.; Baldo, P.M.

    1991-11-01

    Ion irradiation and annealing experiments have been conducted on Au/Cu bilayer films to evaluate the effect of irradiation on diffusion-induced grain boundary migration (DIGM). The Au films were prepared with a large-grained microstructure with grain boundaries perpendicular to the film surface and extending through the film thickness. Irradiations were conducted with 1.5 MeV Kr at 228 degree C. Rutherford backscattering spectrometry of the samples revealed that interdiffusion was substantially enhanced in the irradiated area relative to the unirradiated area. Both irradiated and annealed-only areas were characterized by a nearly uniform composition of 14 at.% and 7 at.% Cu respectively through the entire thickness of the underlying Au film. Small probe X-ray energy dispersive spectroscopy showed significant lateral compositional homogeneities in both irradiated and annealed areas. These two results are consistent with previous observations of DIGM in the Au/Cu system, suggesting that this previously unexamined mechanism contributes to ion beam mixing

  12. Sensitivity analysis of Immersed Boundary Method simulations of fluid flow in dense polydisperse random grain packings

    Directory of Open Access Journals (Sweden)

    Knight Chris

    2017-01-01

    Full Text Available Polydisperse granular materials are ubiquitous in nature and industry. Despite this, knowledge of the momentum coupling between the fluid and solid phases in dense saturated grain packings comes almost exclusively from empirical correlations [2–4, 8] with monosized media. The Immersed Boundary Method (IBM is a Computational Fluid Dynamics (CFD modelling technique capable of resolving pore scale fluid flow and fluid-particle interaction forces in polydisperse media at the grain scale. Validation of the IBM in the low Reynolds number, high concentration limit was performed by comparing simulations of flow through ordered arrays of spheres with the boundary integral results of Zick and Homsy [10]. Random grain packings were studied with linearly graded particle size distributions with a range of coefficient of uniformity values (Cu = 1.01, 1.50, and 2.00 at a range of concentrations (ϕ ∈ [0.396; 0.681] in order to investigate the influence of polydispersity on drag and permeability. The sensitivity of the IBM results to the choice of radius retraction parameter [1] was investigated and a comparison was made between the predicted forces and the widely used Ergun correlation [3].

  13. The grain boundary segregation of phosphorus in thermally aged and irradiated C-Mn submerged-are weld metal

    International Nuclear Information System (INIS)

    Mendes, C.M.

    1999-01-01

    The segregation of free phosphorus atoms to grain boundaries in C-Mn steels has been identified as an embrittlement mechanism. A change in the brittle fracture mechanism from transgranular to intergranular has been observed for materials with higher phosphorus grain boundary coverage. The grain boundary segregation of phosphorus in various steels used in the nuclear power industry has been thermodynamically and kinetically modelled mostly with the Langmuir-McLean model. Recent publications have also suggested that neutron irradiation can affect segregation and various attempts at modelling this are currently under way. The present paper describes a data base assembled on phosphorus grain boundary coverage measured by Auger electron spectroscopy on thermally aged and irradiated C-Mn submerged-arc weld specimens. Software tools were developed to evaluate the changes in phosphorus grain boundary coverage associated with instantaneous temperature changes and temperature gradients. The phosphorus free energy change associated with grain boundary segregation was modelled from the thermally aged data and used with the software to determine the phosphorus segregation in submerged-arc weld metals following the post weld stress relief heat treatments received prior to plant operation. The phosphorus grain boundary coverage changes arising from the thermal history of submerged-arc weld materials during irradiation were also modelled and found to compare well with data obtained on irradiated materials. It was concluded that under the irradiation conditions sampled, phosphorus grain boundary segregation in submerged-arc weld materials can be modelled successfully using only the thermal term without appealing to an irradiation induced segregation process. (author)

  14. {1 1 1} facet growth laws and grain competition during silicon crystallization

    Science.gov (United States)

    Stamelou, V.; Tsoutsouva, M. G.; Riberi-Béridot, T.; Reinhart, G.; Regula, G.; Baruchel, J.; Mangelinck-Noël, N.

    2017-12-01

    Directional solidification from mono-crystalline Si seeds having different orientations along the growth direction is studied. Due to the frequent twinning phenomenon, new grains soon nucleate during growth. The grain competition is then characterized in situ by imaging the dynamic evolution of the grain boundaries and of the corresponding grain boundary grooves that are formed at the solid-liquid interface. To perform this study, an experimental investigation based on Bridgman solidification technique coupled with in situ X-ray imaging is conducted in an original device: GaTSBI (Growth at high Temperature observed by X-ray Synchrotron Beam Imaging). Imaging characterisation techniques using X-ray synchrotron radiation at ESRF (European Synchrotron Radiation Facility, Grenoble, France) are applied during the solidification to study the growth dynamics. Facetted/facetted grain boundary grooves only are studied due to their importance in the grain competition because of their implication in the twinning mechanism. The maximum undercooling inside the groove is calculated from the groove depth knowing the local temperature gradient. Additionally, thanks to dynamic X-ray images, the global solid-liquid interface growth rate and the normal growth rate of the {1 1 1} facets existing at the grooves and at the edges are measured. From these measurements, experimental growth laws that correlate the normal velocity of the {1 1 1} facets with the maximum undercooling of the groove are extracted and compared to existing theoretical models. Finally, the experimental laws found for the contribution to the undercooling of the {1 1 1} facets are in good agreement with the theoretical model implying nucleation and growth eased by the presence of dislocations. Moreover, it is shown that, for the same growth parameters, the undercooling at the level of the facets (always lower than 1 K) is higher at the edges so that there is a higher probability of twin nucleation at the edges which

  15. Atomic simulations of dislocation emission from Cu/Cu and Co/Cu grain boundaries

    International Nuclear Information System (INIS)

    Yuasa, Motohiro; Nakazawa, Takumi; Mabuchi, Mamoru

    2010-01-01

    Research highlights: → Co/Cu bicrystals have both E structures and stacking faults only in the Cu phase. → Dislocations tend to be emitted from the stacking faults in Co/Cu bicrystals. → Large disorder around the stacking faults accelerates the atomic shuffling. → Atomic shuffling behavior strongly affects dislocation emission in Co/Cu bicrystals. - Abstract: Molecular dynamics simulations of creep tests have been performed on Cu/Cu single-phase bicrystals and Co/Cu two-phase bicrystals to investigate the dislocation emission from grain boundaries. In the Co/Cu bicrystals, both E structures and stacking faults were generated only in the Cu grain near the boundary. Dislocations were emitted only from the stacking faults, not from the E structures, in the Co/Cu bicrystals. The stacking faults in the Co/Cu bicrystals did not necessarily enhance the dislocation emission as readily as those in the Cu/Cu bicrystals. The incoherence between Co and Cu gave rise to the complicated defect structures at and near the Co/Cu boundary, and thus distinctive atomic shuffling mechanisms occurred. This affected the dislocation emission behavior of the Co/Cu bicrystals.

  16. Grain Boundary Analysis of the Garnet-like Oxides Li7+X-YLa3-XAXZr2-YNbYO12 (A = Sr or Ca

    Directory of Open Access Journals (Sweden)

    Shingo Ohta

    2016-07-01

    Full Text Available Garnet-like oxides having the formula Li7+X-YLa3-XAXZr2-YNbYO12 (A = Sr or Ca were synthesized using a solid-state reaction and their bulk and grain boundary resistivities were assessed by AC impedance measurements. A difference in grain boundary resistivity was identified between the Sr and Ca materials and so the grain boundaries were examined using electron probe microanalysis (EPMA. The difference in the grain boundary resistivities was attributed to the core-shell structure of the Sr-substituted samples. In contrast, the Ca-substituted materials exhibited accumulations of impurities at the grain boundaries.

  17. Evaluation of local stress and local hydrogen concentration at grain boundary using three-dimensional polycrystalline model

    International Nuclear Information System (INIS)

    Ebihara, Ken-ichi; Itakura, Mitsuhiro; Yamaguchi, Masatake; Kaburaki, Hideo; Suzudo, Tomoaki

    2010-01-01

    The decohesion model in which hydrogen segregating at grain boundaries reduces cohesive energy is considered to explain hydrogen embrittlement. Although there are several experimental and theoretical supports of this model, its total process is still unclear. In order to understand hydrogen embrittlement in terms of the decohesion model, therefore, it is necessary to evaluate stress and hydrogen concentration at grain boundaries under experimental conditions and to verify the grain boundary decohesion process. Under this consideration, we evaluated the stress and the hydrogen concentration at grain boundaries in the three-dimensional polycrystalline model which was generated by the random Voronoi tessellation. The crystallographic anisotropy was given to each grain. As the boundary conditions of the calculations, data extracted from the results calculated in the notched round-bar specimen model under the tensile test condition in which fracture of the steel specimen is observed was given to the polycrystalline model. As a result, it was found that the evaluated stress does not reach the fracture stress which was estimated under the condition of the evaluated hydrogen concentration by first principles calculations. Therefore, it was considered that the initiation of grain boundary fracture needs other factors except the stress concentration due to the crystallographic anisotropy. (author)

  18. Gas accumulation at grain boundaries during 800 MeV proton irradiation of aluminium and aluminium-alloys

    DEFF Research Database (Denmark)

    Singh, Bachu Narain; Horsewell, Andy; Sommer, W. F.

    1986-01-01

    ) showed a complete absence of voids or bubbles in the grain interiors of the aluminium and the aluminium-alloys. Bubbles were clearly visible by TEM at grain boundaries in pure Al and the AlMg3 alloy; but bubbles were not visible in the Al6061 alloy. The bubble density in the AlMg3 alloy was considerably...

  19. Distribution of trace elements in a modified and grain refined aluminium-silicon hypoeutectic alloy.

    Science.gov (United States)

    Faraji, M; Katgerman, L

    2010-08-01

    The influence of modifier and grain refiner on the nucleation process of a commercial hypoeutectic Al-Si foundry alloy (A356) was investigated using optical microscopy, scanning electron microscopy (SEM) and electron probe microanalysis technique (EPMA). Filtering was used to improve the casting quality; however, it compromised the modification of silicon. Effect of filtering on strontium loss was also studied using the afore-mentioned techniques. EPMA was used to trace the modifying and grain refining agents inside matrix and eutectic Si. This was to help understanding mechanisms of nucleation and modification in this alloy. Using EPMA, the negative interaction of Sr and Al3TiB was closely examined. In modified structure, it was found that the maximum point of Sr concentration was in line with peak of silicon; however, in case of just 0.1wt% added Ti, the peak of Ti concentration was not in line with aluminium, (but it was close to Si peak). Furthermore, EPMA results showed that using filter during casting process lowered the strontium content, although produced a cleaner melt. (c) 2010 Elsevier Ltd. All rights reserved.

  20. Viscoelastic sliding and diffusive relaxation along grain boundaries in polycrystalline boron nitride

    International Nuclear Information System (INIS)

    Pezzotti, G.; Nishida, Toshihiko; Kleebe, H.J.; Ota, Kenichi

    1997-01-01

    Dense hexagonal boron nitride (BN) materials were prepared via two different processing routes: (1) hot-pressing with the addition of a Ca/B-containing glass and (2) chemical vapor deposition (CVD). The resulting microstructure of both materials was studied by scanning and transmission electron microscopy. While the hot-pressed BN material shows, apart from large BN matrix grains, an inhomogeneous distribution of residual glass at room temperature, the CVD deposition yields a homogeneous fine grained microstructure with no amorphous residue detectable. Internal-friction experiments were performed to study the micromechanical response of the materials when exposed to high temperatures. The CVD material revealed no relaxation peak during testing up to 2,300 C, while the glass-doped sample showed a pronounced relaxation peak at a peak-top temperature of about 600 C. This temperature corresponds to the softening temperature known for bulk Ca/B-glasses and it is, therefore, concluded that the glass homogeneously wets the BN grains at elevated temperatures. The results presented are seen as the first clear evidence that the internal friction peak monitored for various glass-containing ceramics is indeed related to a viscous sliding process along grain boundaries

  1. Diffraction-amalgamated grain boundary tracking for mapping 3D crystallographic orientation and strain fields during plastic deformation

    International Nuclear Information System (INIS)

    Toda, Hiroyuki; Kamiko, Takanobu; Tanabe, Yasuto; Kobayashi, Masakazu; Leclere, D.J.; Uesugi, Kentaro; Takeuchi, Akihisa; Hirayama, Kyosuke

    2016-01-01

    By amalgamating the X-ray diffraction technique with the grain boundary tracking technique, a novel method, diffraction-amalgamated grain boundary tracking (DAGT), has been developed. DAGT is a non-destructive in-situ analysis technique for characterising bulk materials, which can be applied up to near the point of fracture. It provides information about local crystal orientations and detailed grain morphologies in three dimensions, together with high-density strain mapping inside grains. As it obtains the grain morphologies by utilising X-ray imaging instead of X-ray diffraction, which latter is typically vulnerable to plastic deformation, DAGT is a fairly robust technique for analysing plastically deforming materials. Texture evolution and localised deformation behaviours have here been successfully characterised in Al–Cu alloys, during tensile deformation of 27% in applied strain. The characteristic rotation behaviours of grains were identified, and attributed to the effects of interaction with adjacent grains on the basis of the 3D local orientation and plastic strain distributions. It has also been revealed that 3D strain distribution in grains is highly heterogeneous, which is not explained by known mechanisms such as simple incompatibility with adjacent grains or strain percolation through soft grains. It has been clarified that groups consisting of a few adjacent grains may deform coordinately, especially in shear and lateral deformation, and the characteristic deformation pattern is thereby formed on a mesoscopic scale.

  2. Thermodynamics of coherent interfaces under mechanical stresses. II. Application to atomistic simulation of grain boundaries

    Science.gov (United States)

    Frolov, T.; Mishin, Y.

    2012-06-01

    The thermodynamic theory of coherent interfaces developed in Part I of this work is applied to grain boundaries (GBs) subject to nonhydrostatic elastic deformations. We derive expressions for the GB free energy as the reversible work of GB formation under stress. We also present a generalized adsorption equation whose differential coefficients define the GB segregation, GB stress tensor, GB excess volume, and GB excess shear. The generalized adsorption equation generates a set of Maxwell relations describing cross effects between different GB properties. The theory is applied to atomistic simulations of a symmetrical tilt GB in Cu and Cu-Ag alloys. Using a combination of molecular dynamics and Monte Carlo methods, we compute a number of GB excess quantities and their dependencies on the applied stresses, temperature and chemical composition in the grains. We also test several Maxwell relations and obtain excellent agreement between the theory and simulations.

  3. Atom Probe Tomography of Phase and Grain Boundaries in Experimentally-Deformed and Hot-Pressed Wehrlite

    Science.gov (United States)

    Cukjati, J.; Parman, S. W.; Cooper, R. F.; Zhao, N.

    2017-12-01

    Atom probe tomography (APT) was used to characterize the chemistry of three grain boundaries: an olivine-olivine (ol-ol) and olivine-clinopyroxene (ol-cpx) boundary in fine-grained experimentally-deformed wehrlite and an ol-cpx boundary in a fine-grained, hot-pressed wehrlite. Grain boundaries were extracted and formed into APT tips using a focused ion beam (FIB). The tips were analyzed in a reflectron-equipped LEAP4000HR (Harvard University) at 1% or 0.5% detection rate, 5pJ laser energy and 100kHz pulse rate. Total ion counts are between 40 and 100 million per tip. Examination of grain and phase boundaries in wehrlite are of interest since slow-diffusing and olivine-incompatible cations present in cpx (e.g. Ca and Al) may control diffusion-accommodated grain boundary sliding and affect mantle rheology (Sundberg & Cooper, 2008). At steady state, ol-cpx aggregates are weaker than either ol or cpx end member, the results of which are not currently well-explained. We investigate grain boundary widths to understand the transport of olivine-incompatible elements. Widths of grain/phase boundary chemical segregation are between 3nm and 6nm for deformed ol-ol and ol-cpx samples; minimally-deformed (hot-pressed) samples having slightly wider chemical segregation widths. Chemical segregation widths were determined from profiles of Na, Al, P, Cl, K, Ca, or Ni, although not all listed elements can be used for all samples (e.g. Na, K segregation profiles can only be observed for ol-ol sample). These estimates are consistent with prior estimates of grain boundary segregation by atom probe tomography on ol-ol and opx-opx samples (Bachhav et al., 2015) and are less than ol-ol interface widths analyzed by STEM/EDX (Hiraga, Anderson, & Kohlstedt, 2007). STEM/EDX will be performed on deformed wehrlite to investigate chemical profile as a function of applied stress orientation and at length scales between those observable by APT and EPMA. Determination of phase boundary chemistry and

  4. Intergranular fracture stress and phosphorus grain boundary segregation of a Mn-Ni-Mo steel

    International Nuclear Information System (INIS)

    Naudin, C.; Frund, J.M.; Pineau, A.

    1999-01-01

    Nuclear Reactor Pressure Vessel (RPV) steel A508 class 3 which is a low alloyed steel is not usually sensitive to reversible temper embrittlement when properly heat treated. However heterogeneous zones may be present in particular near the inner side of the vessel. These zones result from the segregation of the alloying elements (C, Mn, Ni, Mo) and impurities (S, P) taking place during solidification of the material. They are called segregated zones (or ghost lines). They can reach 2 mm thick along the radius and 30 mm long through the circumferential direction. Their susceptibility to reversible temper embrittlement is mainly due to grain boundary phosphorus segregation triggering brittle intergranular fracture when the material is tested at low temperature. In this material like in other steels the influence of some other alloying elements (Mo, Mn...) is clearly significant and should also be taken into account. But phosphorus effect has proved to be predominant. The aim of the present study is therefore to find out a quantitative relationship between grain boundary phosphorus segregation and critical intergranular fracture stress. A synthetic steel with a chemical composition representative of an average segregated zone was prepared for the present study. A number of heat treatments were applied to reach different embrittlement conditions. Then brittle fracture properties were obtained by performing cryogenic fracture tests on notched tensile specimens while the corresponding grain boundary phosphorus levels were measured by Auger electron spectroscopy. Systematic fractographic observations were carried out. Moreover an attempt to determine the influence of temperature on the critical intergranular fracture stress was made

  5. Intergranular fracture stress and phosphorus grain boundary segregation of a Mn-Ni-Mo steel

    Energy Technology Data Exchange (ETDEWEB)

    Naudin, C.; Frund, J.M. [EDF, Moret sur Loing (France). Direction des Etudes et Recherches; Pineau, A. [Ecole des Mines de Paris, Evry (France). Centre des Materiaux

    1999-04-09

    Nuclear Reactor Pressure Vessel (RPV) steel A508 class 3 which is a low alloyed steel is not usually sensitive to reversible temper embrittlement when properly heat treated. However heterogeneous zones may be present in particular near the inner side of the vessel. These zones result from the segregation of the alloying elements (C, Mn, Ni, Mo) and impurities (S, P) taking place during solidification of the material. They are called segregated zones (or ghost lines). They can reach 2 mm thick along the radius and 30 mm long through the circumferential direction. Their susceptibility to reversible temper embrittlement is mainly due to grain boundary phosphorus segregation triggering brittle intergranular fracture when the material is tested at low temperature. In this material like in other steels the influence of some other alloying elements (Mo, Mn...) is clearly significant and should also be taken into account. But phosphorus effect has proved to be predominant. The aim of the present study is therefore to find out a quantitative relationship between grain boundary phosphorus segregation and critical intergranular fracture stress. A synthetic steel with a chemical composition representative of an average segregated zone was prepared for the present study. A number of heat treatments were applied to reach different embrittlement conditions. Then brittle fracture properties were obtained by performing cryogenic fracture tests on notched tensile specimens while the corresponding grain boundary phosphorus levels were measured by Auger electron spectroscopy. Systematic fractographic observations were carried out. Moreover an attempt to determine the influence of temperature on the critical intergranular fracture stress was made.

  6. Chirality and grain boundary effects on indentation mechanical properties of graphene coated on nickel foil.

    Science.gov (United States)

    Yan, Yuping; Lv, Jiajiang; Liu, Sheng

    2018-04-20

    We investigate chirality and grain boundary (GB) effects on indentation mechanical properties of graphene coated on nickel foil using molecular dynamics simulations. The models of graphene with different chirality angles, different numbers of layers and tilt GBs were established. It was found that the chirality angle of few-layer graphene had a significant effect on the load bearing capacity of graphene/nickel systems, and this turns out to be more significant when the number of layers is greater than one. The enhancement to the contact stiffness, elastic capacity and the load bearing capacity of graphene with tilt GBs was lower than that of pristine graphene.

  7. Simulation of the structure of vacancies in high angle grain boundaries

    International Nuclear Information System (INIS)

    Bristowe, P.D.; Brokman, A.; Spaepen, F.; Balluffi, R.W.

    1980-06-01

    Since the modeling approach used in an earlier work is used at an atomic level, this is the most appropriate and reliable technique available. To complement this study, however, we have also employed a hard sphere dynamic model and a bubble raft model because in the past they have provided useful qualitative insight into the structure of a variety of defects in two-dimensional crystalline and amorphous systems. The computed results form part of a wider investigation of vacancies and interstitials in various grain boundaries in which the binding energies are analyzed and related to the defect structure and form of the interatomic potential

  8. Influence of grain boundary phosphorus segregation on hydrogen embrittlement in steel

    International Nuclear Information System (INIS)

    Platonov, P.A.; Amaev, A.D.; Nikolaev, V.A.; Tursunov, I.E.; Krasikov, E.A.; Levit, V.I.; Nikitin, S.V.; Biryukov, A.Yu.; Gorskij, K.V.; Popov, V.V.

    1986-01-01

    Experimental investigation into the effect of grain-boundary impurity segregations on hydrogen embrittlement of pearlite steel was carried on. It is shown that thermal ageing during 10 3 and 10 4 h and subsequent hydridation result in complete loss of ductility. At that phosphorus and carbon impurity aggregations form casing synergism between thermal and hydrogen embrittlements. The similar interaction causing the formation of intergranular cracks with out applying external stress can result in fracture of idle steel. The determining effect on the fracture mechanism of hydrogen interaction with intergranular microstructural heterogeneities (in particular, impurity segregations) is noted

  9. Origin of intergranular embrittlement of Al alloys induced by Na and Ca segregation: Grain boundary weakening

    International Nuclear Information System (INIS)

    Lu Guanghong; Zhang Ying; Deng Shenghua; Wang Tianmin; Kohyama, Masanori; Yamamoto, Ryoichi; Liu Feng; Horikawa, Keitaro; Kanno, Motohiro

    2006-01-01

    Using a first-principles computational tensile test, we show that the ideal tensile strength of an Al grain boundary (GB) is reduced with both Na and Ca GB segregation. We demonstrate that the fracture occurs in the GB interface, dominated by the break of the interfacial bonds. Experimentally, we further show that the presence of Na or Ca impurity, which causes intergranular fracture, reduces the ultimate tensile strength when embrittlement occurs. These results suggest that the Na/Ca-induced intergranular embrittlement of an Al alloy originates mainly from the GB weakening due to the Na/Ca segregation

  10. Grain Boundary Engineering of Lithium-Ion-Conducting Lithium Lanthanum Titanate for Lithium-Air Batteries

    Science.gov (United States)

    2016-01-01

    determined from alternating-current electrochemical impedance spectroscopy using a Bio-logic SP200 over a frequency range of 0.1 Hz–7 MHz with a potential... Characterization of grain-boundary phases in Li7La3Zr2O12 solid electrolytes . Materials Characterization . 2014;91:101–106. Approved for public release...battery performance is limited by the electrolytic membrane, which needs high Li-ionic conductivity. Lithium lanthanum titanate (Li3xLa(2/3)-xTiO3, or

  11. Linewidth of Josephson oscillations in YBa2Cu3O7-x grain-boundary junctions

    DEFF Research Database (Denmark)

    Divin, Yu. Ya.; Mygind, Jesper; Pedersen, Niels Falsig

    1993-01-01

    The AC Josephson effect in YBa2Cu3O7-x grain-boundary junctions (GBJs) was studied in the temperature range from 4 K to 90 K. The temperature dependence of the linewidth of millimeter-wave Josephson oscillations was measured, and it is shown that the derived effective noise temperature of GBJ might...... be as low as the physical temperature in the temperature range investigated. This makes it possible to use the resistively shunted junction (RSJ) model with thermal fluctuations to get a limiting performance of high-T c devices utilizing the AC Josephson effect. The lowest value of the linewidth of 72 GHz...

  12. Modelling of planar interface elastic behaviour: Application to grain boundaries in polycrystals

    International Nuclear Information System (INIS)

    Gelebart, L.

    2010-01-01

    In polycrystalline elastic simulations, grain boundaries can be considered as volume inter-phases or as elastic interfaces assuming a displacement jump across the interface. Such an interface description does not account for the in-plane deformation of the interface and Poisson effects cannot be reproduced. The purpose of this Note is to provide an enriched description of the elastic interface which takes into account such effects. When considering a multilayer material, the interphase description and the enriched interface description yield identical homogenized behaviour while quite important discrepancies can be observed with the classical interface description. (author)

  13. Chirality and grain boundary effects on indentation mechanical properties of graphene coated on nickel foil

    Science.gov (United States)

    Yan, Yuping; Lv, Jiajiang; Liu, Sheng

    2018-04-01

    We investigate chirality and grain boundary (GB) effects on indentation mechanical properties of graphene coated on nickel foil using molecular dynamics simulations. The models of graphene with different chirality angles, different numbers of layers and tilt GBs were established. It was found that the chirality angle of few-layer graphene had a significant effect on the load bearing capacity of graphene/nickel systems, and this turns out to be more significant when the number of layers is greater than one. The enhancement to the contact stiffness, elastic capacity and the load bearing capacity of graphene with tilt GBs was lower than that of pristine graphene.

  14. Atomistic simulations on intergranular fracture toughness of copper bicrystals with symmetric tilt grain boundaries

    Science.gov (United States)

    Cui, Cheng Bin; Beom, Hyeon Gyu

    2018-01-01

    The intergranular fracture toughness of Cu bicrystals with symmetric tilt grain boundaries was investigated using atomistic simulations. Mode I fracture of Cu bicrystals with an intergranular crack was considered. The boundary conditions were specified by the near-tip displacement fields obtained based on linear elastic fracture mechanics (LEFM). Based on the energy interpretation of the energy release rate, a two-specimen method was adopted to determine the fracture toughness. The simulation results of the fracture toughness matched well with those determined using LEFM. In contrast to the toughness obtained using the Griffith energy criterion, the atomistic simulation results for the same bicrystal were not constants, but dependent on the crack-tip circumstances. This behavior was mainly associated with the different local stress conditions and fracture patterns observed for the different models.

  15. Direct evaluation of grain boundary hydrogen embrittlement: A micro-mechanical approach

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, Yoshimasa, E-mail: yoshim-t@kansai-u.ac.jp [Department of Mechanical Engineering, Kansai University, 3-3-35 Yamate-cho, Suita-shi, Osaka 564-8680 (Japan); Kondo, Hikaru; Asano, Ryo [Department of Mechanical Engineering, Kansai University, 3-3-35 Yamate-cho, Suita-shi, Osaka 564-8680 (Japan); Arai, Shigeo; Higuchi, Kimitaka; Yamamoto, Yuta; Muto, Shunsuke; Tanaka, Nobuo [Institute of Materials and Systems for Sustainability (IMaSS), Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan)

    2016-04-20

    In order to directly investigate the grain boundary (GB) hydrogen embrittlement in polycrystalline materials, a novel micro-mechanical testing method was developed. By combining a site-specific sampling technique and a high-voltage environmental transmission electron microscope (HV ETEM), the fracture property of micro-cantilever specimens fabricated from the same GB in a nickel-aluminide (Ni{sub 3}Al) polycrystal was critically compared in environments with/without hydrogen (H{sub 2}) gas. For randomly oriented GBs, brittle fracture nucleation accompanied by plastic deformation was observed in a H{sub 2}-containing environment except for ones with small orientation difference. No GB fracture was observed for coherent Σ3 boundaries. It also appeared that the similitude of the hydrogen-enhanced decohesion (HEDE) mechanism was still valid even for the submicron-scale specimens.

  16. Special grain boundaries in the nugget zone of friction stir welded AA6061-T6 under various welding parameters

    Energy Technology Data Exchange (ETDEWEB)

    Tao, Wang [Key Lab of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Yong, Zou, E-mail: yzou@sdu.edu.cn [Key Lab of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Xuemei, Liu [Key Lab of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Matsuda, Kenji [Department of Materials Science and Technology, Faculty of Engineering, University of Toyama, Toyama 930-8555 (Japan)

    2016-08-01

    The age hardenable AA6061-T6 plate was butt welded by friction stir welding. The total heat input, generated by friction between the tool and work piece and plastic deformation, results in a consumption of meta-stable phases in the nugget zone. Precipitation phenomena were closely related to the diffusion of the solute atoms. The existence of special grain boundaries like Σ1a and Σ3 will increase the difficulty in diffusion, which will improve the hardness in the nugget zone. Furthermore, the formation of Σ3 grain boundaries can result from an impingement of re-crystallized grains coming from texture components in twin relationship already. An appropriate strain level may benefit the development of the twin components with a similar intensity. The welding parameters have an effect on heat source mode and the strain level. Then, the type of dynamic re-crystallization and distribution of the special grain boundaries was altered by changing the parameters.

  17. Effect of one-step recrystallization on the grain boundary evolution of CoCrFeMnNi high entropy alloy and its subsystems.

    Science.gov (United States)

    Chen, Bo-Ru; Yeh, An-Chou; Yeh, Jien-Wei

    2016-02-29

    In this study, the grain boundary evolution of equiatomic CoCrFeMnNi, CoCrFeNi, and FeCoNi alloys after one-step recrystallization were investigated. The special boundary fraction and twin density of these alloys were evaluated by electron backscatter diffraction analysis. Among the three alloys tested, FeCoNi exhibited the highest special boundary fraction and twin density after one-step recrystallization. The special boundary increment after one-step recrystallization was mainly affected by grain boundary velocity, while twin density was mainly affected by average grain boundary energy and twin boundary energy.

  18. Simulation of xenon, uranium vacancy and interstitial diffusion and grain boundary segregation in UO2

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Anders D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Tonks, Michael R. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Casillas, Luis [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Nerikar, Pankaj [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Vyas, Shyam [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Uberuaga, Blas P. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stanek, Christopher R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-10-31

    In light water reactor fuel, gaseous fission products segregate to grain boundaries, resulting in the nucleation and growth of large intergranular fission gas bubbles. Based on the mechanisms established from density functional theory (DFT) and empirical potential calculations 1, continuum models for diffusion of xenon (Xe), uranium (U) vacancies and U interstitials in UO2 have been derived for both intrinsic conditions and under irradiation. Segregation of Xe to grain boundaries is described by combining the bulk diffusion model with a model for the interaction between Xe atoms and three different grain boundaries in UO2 ( Σ5 tilt, Σ5 twist and a high angle random boundary),as derived from atomistic calculations. All models are implemented in the MARMOT phase field code, which is used to calculate effective Xe and U diffusivities as well as redistribution for a few simple microstructures.

  19. Atomic-scale investigations of grain boundary segregation in astrology with a three dimensional atom-probe

    Energy Technology Data Exchange (ETDEWEB)

    Blavette, D. [Rouen Univ., 76 - Mont-Saint-Aignan (France). Lab. de Microscopie Electronique]|[Institut Universitaire de France (France); Letellier, L. [Rouen Univ., 76 - Mont-Saint-Aignan (France). Lab. de Microscopie Electronique; Duval, P. [Rouen Univ., 76 - Mont-Saint-Aignan (France). Lab. de Microscopie Electronique; Guttmann, M. [Rouen Univ., 76 - Mont-Saint-Aignan (France). Lab. de Microscopie Electronique]|[Institut de Recherches de la Siderurgie Francaise (IRSID), 57 - Maizieres-les-Metz (France)

    1996-08-01

    Both conventional and 3D atom-probes were applied to the investigation of grain-boundary (GB) segregation phenomena in two-phase nickel base superalloys Astroloy. 3D images as provided by the tomographic atom-probe reveal the presence of a strong segregation of both boron and molybdenum at grain-boundaries. Slight carbon enrichment is also detected. Considerable chromium segregation is exhibited at {gamma}`-{gamma}` grain-boundaries. All these segregants are distributed in a continuous manner along the boundary over a width close to 0.5 nm. Experiments show that segregation occurs during cooling and more probably between 1000 C and 800 C. Boron and molybdenum GB enrichments are interpreted as due to an equilibrium type-segregation while chromium segregation is thought to be induced by {gamma}` precipitation at GB`s and stabilised by the presence of boron. No segregation of zirconium is detected. (orig.)

  20. Analytical modeling of elastic-plastic wave behavior near grain boundaries in crystalline materials

    Energy Technology Data Exchange (ETDEWEB)

    Loomis, Eric [Los Alamos National Laboratory; Greenfield, Scott [Los Alamos National Laboratory; Luo, Shengnian [Los Alamos National Laboratory; Swift, Damian [LLNL; Peralta, Pedro [ASU

    2009-01-01

    It is well known that changes in material properties across an interface will produce differences in the behavior of reflected and transmitted waves. This is seen frequently in planar impact experiments, and to a lesser extent, oblique impacts. In anisotropic elastic materials, wave behavior as a function of direction is usually accomplished with the aid of velocity surfaces, a graphical method for predicting wave scattering configurations. They have expanded this method to account for inelastic deformation due to crystal plasticity. The set of derived equations could not be put into a characteristic form, but instead led to an implicit problem. to overcome this difficulty an algorithm was developed to search the parameters space defined by a wave normal vector, particle velocity vector, and a wave speed. A solution was said to exist when a set from this parameter space satisfied the governing vector equation. Using this technique they can predict the anisotropic elastic-plastic velocity surfaces and grain boundary scattering configuration for crystalline materials undergoing deformation by slip. Specifically, they have calculated the configuration of scattered elastic-plastic waves in anisotropic NiAl for an incident compressional wave propagating along a <111> direction and contacting a 45 degree inclined grain boundary and found that large amplitude transmitted waves exist owing to the fact that the wave surface geometry forces it to propagate near the zero Schmid factor direction <100>.

  1. Disorder-induced transition from grain boundary to bulk dominated ionic diffusion in pyrochlores

    International Nuclear Information System (INIS)

    Perriot, Romain; Dholabhai, Pratik P.; Uberuaga, Blas P.

    2017-01-01

    In this paper, we use molecular dynamics simulations to investigate the role of grain boundaries (GBs) on ionic diffusion in pyrochlores, as a function of the GB type, chemistry of the compound, and level of cation disorder. We observe that the presence of GBs promotes oxygen transport in ordered and low-disordered systems, as the GBs are found to have a higher concentration of mobile carriers with higher mobilities than in the bulk. Thus, in ordered samples, the ionic diffusion is 2D, localized along the grain boundary. When cation disorder is introduced, bulk carriers begin to contribute to the overall diffusion, while the GB contribution is only slightly enhanced. In highly disordered samples, the diffusive behavior at the GBs is bulk-like, and the two contributions (bulk vs. GB) can no longer be distinguished. There is thus a transition from 2D/GB dominated oxygen diffusivity to 3D/bulk dominated diffusivity versus disorder in pyrochlores. Finally, these results provide new insights into the possibility of using internal interfaces to enhance ionic conductivity in nanostructured complex oxides.

  2. The effect of molybdenum on the grain boundary segregation of phosphorus in steel

    International Nuclear Information System (INIS)

    Moller, R.; Brenner, S.S.; Grabke, A.J.

    1986-01-01

    The beneficial effect of molybdenum on the temper embrittlement of steels is well known but has not yet been satisfactorily explained. Yu and McMahon suggested a strong interaction between molybdenum and phosphorus to form Mo-P clusters which decrease the concentration of phosphorus in the matrix and consequently the amount segregated to grain boundaries. Such clusters have as yet not been observed but this may have been owing to the insufficient resolution of conventional analytical methods. However, since no scavenging of phosphorus was observed in carbon-free Fe-Mo-P alloys, i.e. Mo alone did not affect the grain boundary concentration of phosphorus, it is improbable that the Mo-P cluster formation mechanisms can be operative. Instead, it is more likely that a requisite for the scavenging of phosphorus is the formation of Mo carbides in the steel. This work was undertaken to determine the distribution of phosphorus in two similar Fe-Mo-P alloys, one of which contained carbon while the other was carbon-free. The emphasis of the study was to determine the interaction of phosphorus with molybdenum and molybdenum carbides in the steel. Field-ion microscopy combined with atom probe microanalysis was used for this purpose. The atom-by-atom sampling method and the near-atomic spatial resolution of the FIM/atom probe make this instrument ideally suited for this type of investigations

  3. Diffusion of He interstitial and di-He cluster at grain boundaries in α-Fe

    International Nuclear Information System (INIS)

    Gao, F.; Heinisch, H.L.; Kurtz, R.J.

    2007-01-01

    A systematic molecular dynamics study of the diffusion mechanisms of He interstitial and di-He cluster at two representative interfaces has been carried out in α-Fe. The diffusion coefficient of a He interstitial and the effective migration energies were determined. The He atom diffuses along the Σ11 grain boundary one-dimensionally along specific directions, while it migrates two-dimensionally at low temperatures, and three-dimensionally at higher temperatures, in the Σ3 grain boundary. The di-He interstitial cluster can migrate rapidly along the Σ3 interface at low temperatures, but not at the Σ11 interface. It has been observed that a di-He interstitial cluster can kick out a self interstitial atom (SIA) at high temperatures, forming a He 2 V complex. The SIA migrates rapidly near interfaces, whereas the He 2 V complex is immobile at the temperatures considered. This small cluster may serve as the smallest nucleation for the formation of helium bubbles at interfaces

  4. Creep crack growth by grain boundary cavitation under monotonic and cyclic loading

    Science.gov (United States)

    Wen, Jian-Feng; Srivastava, Ankit; Benzerga, Amine; Tu, Shan-Tung; Needleman, Alan

    2017-11-01

    Plane strain finite deformation finite element calculations of mode I crack growth under small scale creep conditions are carried out. Attention is confined to isothermal conditions and two time histories of the applied stress intensity factor: (i) a monononic increase to a plateau value subsequently held fixed; and (ii) a cyclic time variation. The crack growth calculations are based on a micromechanics constitutive relation that couples creep deformation and damage due to grain boundary cavitation. Grain boundary cavitation, with cavity growth due to both creep and diffusion, is taken as the sole failure mechanism contributing to crack growth. The influence on the crack growth rate of loading history parameters, such as the magnitude of the applied stress intensity factor, the ratio of the applied minimum to maximum stress intensity factors, the loading rate, the hold time and the cyclic loading frequency, are explored. The crack growth rate under cyclic loading conditions is found to be greater than under monotonic creep loading with the plateau applied stress intensity factor equal to its maximum value under cyclic loading conditions. Several features of the crack growth behavior observed in creep-fatigue tests naturally emerge, for example, a Paris law type relation is obtained for cyclic loading.

  5. Ab Initio Study of Electronic Transport in Cubic-HfO2 Grain Boundaries

    Directory of Open Access Journals (Sweden)

    Elena Degoli

    2017-01-01

    Full Text Available In polycrystalline materials the grain boundaries (GBs are particularly important as they can act as a sink for atom defects and impurities, which may drive structural transformation of the materials and consequently modify their properties. Characterising the structure and properties of GBs is critical for understanding and controlling material property. Here, we investigated how GBs can modify the structural, electronic, and transport properties of the polycrystalline material HfO2. In general, grain boundaries are considered to be detrimental to the physical stability and electronic transport in HfO2. Anyway, studying by first principles the two most stable and common types of GBs, the tilt and the twist, we found substantial differences on the impact they have on the material properties. In fact, while tilt defects create channels of different sizes and shapes in hafnia along which the electronic transport is stronger in relation to leakage current through GBs, twist defects create a sort of amorphous structure that tends to resemble the bulk and which is independent of the number of rotated planes/atoms.

  6. A study on test variables effected on grain boundary etching test

    International Nuclear Information System (INIS)

    Baek, Seung Se; Na, Sung Hoon; Yu, Hyo Sun; Lee, Hae Moo

    2001-01-01

    Recently the non-destructive test technique which uses the grain boundary etching characteristics owing to the variation of material structures has been proposed. However, during in-serviced GEM test there are a lot of variables such as the changes of temperature and concentration of etching solution, the roughness condition of surface polished etc.. The purpose of this paper is to investigate the influences of these test variables on GEM test results in order to establish a reliable and sensitive of GEM evaluation technique. The experiments are conducted in various solution temperatures, 10 deg. C, 15 .deg. C, 20 .deg. C, and 25 .deg. C and in 70% and 100% concentrations of that, and in various surface roughnesses polished by no.800, no.2000, and 0.3μm alumina powder. Through the test with variables, it is verified that the decrease of temperature and concentration of etching solution and the coarsened surface roughness by not using polishing cloth and powder induce some badly and/or greatly influences on GEM test results like grain boundary etching width(W GB ) and intersecting point ratio(N i /N o ). Therefore, to get reliable and good GEM test results, it must be prepared the surface of specimen polished by polishing cloth and 0.3μm alumina powder and the saturated picric acid solution having 25 .deg. C and be maintained the constant temperature(25 .deg. C) during GEM test

  7. Nanocrystalline CsPbBr3 thin films: a grain boundary opto-electronic study

    Science.gov (United States)

    Conte, G.; Somma, F.; Nikl, M.

    2005-01-01

    CsPbBr3 thin films with nanocrystalline morphology were studied by using optoelectronic techniques to infer the grain boundary region in respect of the crystallite's interior performance. Co-evaporation of puri-fied powders or crushed Bridgman single crystals were used to deposit materials and compare recombina-tion mechanism and dielectric relaxation processes within them. Nanosecond photoconduction decay was observed on both materials as well as activated hopping transport. An asymmetric Debye-like peak was evaluated from impedance spectroscopy with a FWHM value, which remains constant for 1.25 +/- 0.02 deca-des, addressing the presence of a tight conductivity relaxation times distribution. The evaluated activation energy, equal to 0.72 +/- 0.05 eV, similar to that estimated by DC measurements, is well smaller then that expected for an intrinsic material with exciton absorption at 2.36 eV. A simple model based on Voigt's elements was used to model the electronic characteristics of these nanostructured materials, to discuss observed results and define the role played by grain boundaries.

  8. How grain boundaries affect the efficiency of poly-CdTe solar-cells: A fundamental atomic-scale study of grain boundary dislocation cores using CdTe bi-crystal thin films.

    Energy Technology Data Exchange (ETDEWEB)

    Klie, Robert [Univ. of Illinois, Chicago, IL (United States)

    2016-10-25

    It is now widely accepted that grain boundaries in poly-crystalline CdTe thin film devices have a detrimental effect on the minority carrier lifetimes, the open circuit voltage and therefore the overall solar-cell performance. The goal of this project was to develop a fundamental understanding of the role of grain boundaries in CdTe on the carrier life-time, open-circuit voltage, Voc, and the diffusion of impurities. To achieve this goal, i) CdTe bi-crystals were fabricated with various misorientation angels, ii) the atomic- and electronic structures of the grain boundaries were characterized using scanning transmission electron microscopy (STEM), and iii) first-principles density functional theory modeling was performed on the structures determined by STEM to predict the grain boundary potential. The transport properties and minority carrier lifetimes of the bi-crystal grain boundaries were measured using a variety of approaches, including TRPL, and provided feedback to the characterization and modeling effort about the effectiveness of the proposed models.

  9. Atom probe crystallography: Characterization of grain boundary orientation relationships in nanocrystalline aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Moody, Michael P., E-mail: michael.moody@sydney.edu.au [Australian Centre for Microscopy and Microanalysis, The University of Sydney, NSW 2006 (Australia); Tang, Fengzai [Australian Centre for Microscopy and Microanalysis, The University of Sydney, NSW 2006 (Australia); Gault, Baptiste [Australian Centre for Microscopy and Microanalysis, The University of Sydney, NSW 2006 (Australia); Department of Materials, University of Oxford, Oxford OX13PH (United Kingdom); Ringer, Simon P.; Cairney, Julie M. [Australian Centre for Microscopy and Microanalysis, The University of Sydney, NSW 2006 (Australia)

    2011-05-15

    Spatial Distribution Maps (SDM) in their various forms have previously been used to identify and characterize crystallographic structure within APT reconstructions. Importantly, it has been shown that such SDM analyses can also provide the crystallographic orientation of the specimen with respect to the direction of the detector in the original experiment. In this study, we investigate the application of SDMs to the analysis of APT reconstruction of a nanocrystalline Al film. We demonstrate that significant intra-granular crystallographic information is retained in the reconstruction, even in the x-y plane perpendicular to the direction of the detector. Further, the crystallographic orientation of the grains can be characterized highly accurately not only with respect to the bulk specimen but also their misorientation with respect to neighbouring grains. -- Research Highlights: {yields} Atom probe crystallography applied to the characterization of nanocrystalline Al. {yields} SDM analyses reveal intra-granular crystallographic information in-depth and laterally. {yields} SDM characterization enabled estimation of grain boundary orientation relationships.

  10. Effects of DC bias on magnetic performance of high grades grain-oriented silicon steels

    Science.gov (United States)

    Ma, Guang; Cheng, Ling; Lu, Licheng; Yang, Fuyao; Chen, Xin; Zhu, Chengzhi

    2017-03-01

    When high voltage direct current (HVDC) transmission adopting mono-polar ground return operation mode or unbalanced bipolar operation mode, the invasion of DC current into neutral point of alternating current (AC) transformer will cause core saturation, temperature increasing, and vibration acceleration. Based on the MPG-200D soft magnetic measurement system, the influence of DC bias on magnetic performance of 0.23 mm and 0.27 mm series (P1.7=0.70-1.05 W/kg, B8>1.89 T) grain-oriented (GO) silicon steels under condition of AC / DC hybrid excitation were systematically realized in this paper. For the high magnetic induction GO steels (core losses are the same), greater thickness can lead to stronger ability of resisting DC bias, and the reasons for it were analyzed. Finally, the magnetostriction and A-weighted magnetostriction velocity level of GO steel under DC biased magnetization were researched.

  11. Shear response of grain boundaries with metastable structures by molecular dynamics simulations

    Science.gov (United States)

    Zhang, Liang; Lu, Cheng; Shibuta, Yasushi

    2018-04-01

    Grain boundaries (GBs) can play a role as the favored locations to annihilate point defects, such as interstitial atoms and vacancies. It is thus highly probable that different boundary structures can be simultaneously present in equilibrium with each other in the same GB, and thus the GB achieves a metastable state. However, the structural transition and deformation mechanism of such GBs are currently not well understood. In this work, molecular dynamics simulations were carried out to study the multiple structures of a Σ5(310)/[001] GB in bicrystal Al and to investigate the effect of structural multiplicity on the mechanical and kinetic properties of such a GB. Different GB structures were obtained by changing the starting atomic configuration of the bicrystal model, and the GB structures had significantly different atomic density. For the Σ5(310) GB with metastable structures, GB sliding was the dominant mechanism at a low temperature (T = 10 K) under shear stress. The sliding mechanism resulted from the uncoordinated transformation of the inhomogeneous structural units. The nucleation of voids was observed during GB sliding at the low temperature, and the voids subsequently evolved to a nanocrack at the boundary plane. Increasing the temperature can induce the structural transition of local GB structures and can change their overall kinetic properties. GB migration with occasional GB sliding dominated the deformation mechanism at elevated temperatures (T = 300 and 600 K), and the migration process of the metastable GB structures is closely related to the thermally assisted diffusion mechanism.

  12. Structural and chemical analysis of grain boundaries and tellurium precipitates in commercial Cd1-xZnxTe

    International Nuclear Information System (INIS)

    Heffelfinger, J.R.; Medlin, D.L.; James, R.B.

    1998-01-01

    The structure and chemistry of grain boundaries in commercial Cd 1-x Zn x Te, prepared by the high-pressure Bridgman technique, have been analyzed using transmission electron microscopy, scanning electron microscopy, infrared-light microscopy and visible-light microscopy. These analyses show that the grain boundaries inside the Cd 1-x Zn x Te materials are decorated with tellurium precipitates. Analysis of a tellurium precipitate at a grain boundary by transmission electron microscopy and selected-area electron diffraction found the precipitate to consist of a single, saucer-shaped grain. Electron diffraction from the precipitate was consistent with the trigonal phase of tellurium (space group P3 1 21), which is the equilibrium phase at room temperature and atmospheric pressure. This precipitate was found to be aligned with one of the adjacent CZT grains such that the tellurium (0 bar 111) planes were nearly parallel to the CZT (111) planes. High-resolution transmission electron microscopy of the Te/Cd 1-x Zn x Te interface showed no tertiary phase at the interface. The structures of the grain boundaries and the Te/Cd 1-x Zn x Te interface are discussed and related to their possible implications on Cd 1-x Zn x Te gamma-ray detector performance

  13. Effects of DC bias on magnetic performance of high grades grain-oriented silicon steels

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Guang; Cheng, Ling [Global Energy Interconnection Research Institute, State Key Laboratory of Advanced Transmission Technology,Beijing 102211 (China); Lu, Licheng [State Grid Corporation of China, Beijing 100031 (China); Yang, Fuyao; Chen, Xin [Global Energy Interconnection Research Institute, State Key Laboratory of Advanced Transmission Technology,Beijing 102211 (China); Zhu, Chengzhi [State Grid Zhejiang Electric Power Company, Hangzhou 310007 (China)

    2017-03-15

    When high voltage direct current (HVDC) transmission adopting mono-polar ground return operation mode or unbalanced bipolar operation mode, the invasion of DC current into neutral point of alternating current (AC) transformer will cause core saturation, temperature increasing, and vibration acceleration. Based on the MPG-200D soft magnetic measurement system, the influence of DC bias on magnetic performance of 0.23 mm and 0.27 mm series (P{sub 1.7}=0.70–1.05 W/kg, B{sub 8}>1.89 T) grain-oriented (GO) silicon steels under condition of AC / DC hybrid excitation were systematically realized in this paper. For the high magnetic induction GO steels (core losses are the same), greater thickness can lead to stronger ability of resisting DC bias, and the reasons for it were analyzed. Finally, the magnetostriction and A-weighted magnetostriction velocity level of GO steel under DC biased magnetization were researched. - Highlights: • Magnetic properties of 0.23 mm and 0.27 mm series (P{sub 1.7}=0.70–1.05 W/kg, B{sub 8}>1.89 T) grain-oriented (GO) silicon steels under condition of AC / DC hybrid excitation were systematically analyzed. • Influence of DC biased magnetization on core loss, magnetostriction, and A-weighted magnetostriction velocity level of GO steel were researched. • Greater thickness and relatively lower magnetic induction (B{sub 8}>1.89 T yet) of GO steel can lead to stronger ability of resisting DC bias, and the reasons for it were analyzed.

  14. Irradiation-assisted stress corrosion cracking of materials from commercial BWRs: Role of grain-boundary microchemistry

    International Nuclear Information System (INIS)

    Chung, H.M.; Ruther, W.E.; Sanecki, J.E.; Hins, A.G.; Kassner, T.F.

    1994-01-01

    Constant-extension-rate tensile tests and grain-boundary analysis by Auger electron spectroscopy were conducted on high- and commercial-purity (HP and CP) Type 304 stainless steel (SS) specimens from irradiated boiling-water reactor (BWR) components to determine susceptibility to irradiation-assisted stress corrosion cracking (IASCC) and to identify the mechanisms of intergranular failure. The susceptibility of HP neutron absorber tubes to intergranular stress corrosion cracking (IGSCC) was higher than that of CP absorber tubes or CP control blade sheath. Contrary to previous beliefs, susceptibility to intergranular fracture could not be correlated with radiation-induced segregation of impurities such as Si, P, C, N, or S, but a correlation was obtained with grain-boundary Cr concentration, indicating a role for Cr depletion that promotes IASCC. Detailed analysis of grain-boundary chemistry was conducted on neutron absorber tubes that were fabricated from two similar heats of HP Type 304 SS of virtually identical bulk chemical composition but exhibiting a significant difference in susceptibility to IGSCC for similar fluence. Grain-boundary concentrations of Cr, Ni, Si, P, S, and C in the crack-resistant and -susceptible HP heats were virtually identical. However, grain boundaries of the cracking-resistant material contained less N and more B and Li (transmutation product from B) than those of the crack-susceptible material, indicating beneficial effects of low N and high B contents

  15. Effect of Primary Recrystallized Microstructure and Nitriding on Secondary Recrystallization in Grain Oriented Silicon Steel by Low Temperature Slab Reheating

    Directory of Open Access Journals (Sweden)

    LIU Gong-tao

    2018-01-01

    Full Text Available Different primary recrystallized grain sizes were obtained by controlling decarburization process in grain oriented silicon steel produced by low temperature slab reheating technique. The effect of primary grain size on secondary recrystallization and magnetic properties was studied. The appropriate nitrogen content after nitriding was explored in case of very large primary grain size, and the effect of {411}〈148〉 primary recrystallized texture on the abnormal growth behavior was discussed. The results show that an increase in average primary grain size from 10μm to 15μm leads to an increase of secondary recrystallization temperature and a sharper Goss texture with higher magnetic permeability, in the condition of a very large average primary grain size of 28μm, the suitable amount of nitrogen increases to about 6×10-4. The {411}〈148〉 oriented grains in primary recrystallized microstructure can easily grow into larger sizes due to their size advantage, and thus hinder the abnormal growth of secondary grains, moreover, the hindering effect is more pronounced in the abnormal growth of Brass-oriented grains due to their misorientation with low migration rate other than Goss grains.

  16. Intermediate temperature grain boundary embrittlement in nickel-base weld metals

    Science.gov (United States)

    Nissley, Nathan Eugene

    The ductility-dip cracking (DDC) susceptibility of NiCrFe filler metals was evaluated using the strain-to-fracture (STF) GleebleRTM-based testing technique1. These high chromium Ni-base filler metals are frequently used in nuclear power plant applications for welding Ni-base Alloy 690 and included INCONELRTM Filler Metal 52 and 52M (FM-52 and FM-52M)2, and a number of FM-52M-type experimental alloys including two with additions of molybdenum and niobium. A wide range in DDC susceptibilities was observed in the tested alloys including significant variations in susceptibility with only small compositional changes. The interpretation of the STF results now includes both the threshold strain for cracking and the transition to "massive" cracking. While the threshold strain is still insightful and an indication of cracking susceptibility, materials which transition rapidly from the threshold strain to "massive" cracking are typically more susceptible to DDC. The spot pre-welds made on the STF samples, used to produce a repeatable microstructure were found to significantly affect the DDC resistance when the current downslope time was altered. Decreasing the downslope time resulted in a faster cooling rate, finer solidification substructure, fewer metastable intragranular precipitates, and a reduced DDC susceptibility. The downslope time has been found to be the most important STF testing variable evaluated to date. A significant decrease in DDC susceptibility was observed in the alloys with Mo and Nb additions. The threshold strain for cracking in the 2.5% Nb and 4% Mo NiCrFe alloy was approximately 10%, and demonstrated a DDC resistance of more than twice that observed in typical FM-82 alloys. This remarkable increase in DDC resistance was attributed to the skeletal precipitate morphology whose large surface area and dense distribution were highly effective at pinning grain boundaries and preventing crack initiation. The resulting wavy or tortuous grain boundaries act to

  17. Influence of fraction of high angle boundaries on the mechanical behavior of an ultrafine grained Al-Mg alloy

    Energy Technology Data Exchange (ETDEWEB)

    Kapoor, R.; Kumar, N. [Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409 (United States); Mishra, R.S., E-mail: rsmishra@mst.edu [Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409 (United States); Huskamp, C.S.; Sankaran, K.K. [Boeing Research and Technology, Boeing Company, St. Louis, MO 63166 (United States)

    2010-07-25

    The mechanical behavior of ultrafine grained AA5052 processed through different techniques-rolled, annealed, friction stir processed (FSP) and equal channel angular pressed (ECAP)-were compared and correlated with microstructure. The microstructure was characterized using electron back scattered diffraction to obtain the boundary spacing, the fraction of high angle boundaries and to estimate the dislocation density from local misorientations. Both FSP and ECAP conditions had ultrafine boundary spacing, but the fraction of high angle boundaries was larger for the FSP condition. Tensile deformation carried out at 297 K and 10{sup -3} s{sup -1} showed a lower work-hardening rate and recovery rate for FSP as compared to the ECAP condition. It was inferred that low angle boundaries are more effective sinks for dislocations. When comparing differently processed materials, the strength, ductility and work-hardening behavior correlate better with the fraction of high angle boundaries than the boundary spacing.

  18. Low temperature processing of a large grain polycrystalline silicon thin film on soda-lime glass

    International Nuclear Information System (INIS)

    Wang, Kai; Wong, Kin Hung

    2011-01-01

    We have demonstrated that a polycrystalline silicon thin film can be fabricated in situ on soda-lime glass at 450 °C by an Al-induced crystallization method using electron beam evaporation. The catalytic Al is found to diffuse to the top of the crystallized Si layer and can be easily etched away by a mixture of acids. This low temperature Si crystallization process is well explained by thermodynamic consideration. Subsequent annealing at the same temperature (450 °C) for 6 h improves the crystallinity of the film and enlarges the average grain size to over 5 µm. There are no observable impurity phases. The poly-Si thin films are (1 1 1) oriented and all the grains are well aligned. A defect-free and excellent crystalline structure has been revealed by transmission electron microscopy. The measured resistivity, carrier concentration and charge mobility of these as-prepared poly-Si thin films indicate that our present low temperature processing technique has great advantage and prospect for the photonics industry

  19. Low temperature processing of a large grain polycrystalline silicon thin film on soda-lime glass

    Science.gov (United States)

    Wang, Kai; Wong, Kin Hung

    2011-09-01

    We have demonstrated that a polycrystalline silicon thin film can be fabricated in situ on soda-lime glass at 450 °C by an Al-induced crystallization method using electron beam evaporation. The catalytic Al is found to diffuse to the top of the crystallized Si layer and can be easily etched away by a mixture of acids. This low temperature Si crystallization process is well explained by thermodynamic consideration. Subsequent annealing at the same temperature (450 °C) for 6 h improves the crystallinity of the film and enlarges the average grain size to over 5 µm. There are no observable impurity phases. The poly-Si thin films are (1 1 1) oriented and all the grains are well aligned. A defect-free and excellent crystalline structure has been revealed by transmission electron microscopy. The measured resistivity, carrier concentration and charge mobility of these as-prepared poly-Si thin films indicate that our present low temperature processing technique has great advantage and prospect for the photonics industry.

  20. Modification of the grain boundary microstructure of the austenitic PCA stainless steel to improve helium embrittlement resistance

    International Nuclear Information System (INIS)

    Maziasz, P.J.; Braski, D.N.

    1986-01-01

    Grain boundary MC precipitation was produced by a modified thermal-mechanical pretreatment in 25% cold worked (CW) austenitic prime candidate alloy (PCA) stainless steel prior to HFIR irradiation. Postirradiation tensile results and fracture analysis showed that the modified material (B3) resisted helium embrittlement better than either solution annealed (SA) or 25% CW PCA irradiated at 500 to 600 0 C to approx.21 dpa and 1370 at. ppM He. PCA SA and 25% CW were not embrittled at 300 to 400 0 C. Grain boundary MC survives in PCA-B3 during HFIR irradiation at 500 0 C but dissolves at 600 0 C; it does not form in either SA or 25% CW PCA during similar irradiation. The grain boundary MC appears to play an important role in the helium embrittlement resistance of PCA-B3

  1. Effect of residual stress and hardening on grain boundary sliding in welds of low-carbon stainless steels with surface machining

    International Nuclear Information System (INIS)

    Mori, Hiroaki; Mochizuki, Masahito; Nishimoto, Kazutoshi; Katsuyama, Jinya

    2008-01-01

    To clarify the effects of residual stress and hardening on intergranular stress corrosion cracking (IGSCC) behavior in welds of low-carbon austenitic stainless steels with surface machining, residual stress and hardness were evaluated by 3-dimentional thermo elastic-plastic analysis and grain boundary sliding behavior was examined using a constant strain rate tensile test. It was revealed that grain boundary sliding occurred in the material at 561K by the tensile test with the numerically simulated tensile residual stress due to multi-pass welding and surface machining. In addition, it was clarified that the grain boundary energy is raised by the grain boundary sliding. On the basis of these results, it was concluded that the cause of IGSCC in the welds of low-carbon austenitic stainless steel with surface hardening is the increase in grain boundary energy due to grain boundary sliding induced by residual stress of multi pass welding and surface hardening. (author)

  2. First-principles investigation into the effect of Cr on the segregation of multi-H at the Fe Σ3 (1 1 1) grain boundary

    International Nuclear Information System (INIS)

    He, Bingling; Xiao, Wei; Hao, Wei; Tian, Zhixue

    2013-01-01

    First-principles calculations were carried out to investigate the effect of Cr on segregation of multiple H atoms in the Σ3 (1 1 1) grain boundary in bcc Fe. In the absence of Cr, four H atoms can be trapped at the interstitial site of the Fe grain boundary (areal density: 28 nm −2 ), and no H 2 molecules are formed. The presence of Cr, however, suppresses the segregation tendency of H and only two H atoms can be trapped at this grain boundary. Although the volume expansion associated with the segregation of Cr to the grain boundary promotes H segregation, such a booting effect is unable to remedy the repulsion of H resulted from charge density increase in the grain boundary core. As a consequence, Cr mitigates H aggregation at the Σ3 (1 1 1) grain boundary in bcc Fe

  3. Micromagnetic simulation of the influence of grain boundary on cerium substituted Nd-Fe-B magnets

    Directory of Open Access Journals (Sweden)

    D. Liu

    2017-05-01

    Full Text Available A three-dimensional finite element model was performed to study the magnetization reversal of (CexNd1-x2Fe14B nanocomposite permanent magnets. The influences of volume fraction, width and performance parameters of the grain boundary (GB composition on the coercivity were analyzed by the method of micromagnetic simulation. The calculation results indicate that the structure and chemistry of GB phase play important roles in Nd2Fe14B-based magnets. An abnormal increase in the value of coercivity is found to be connected with the GB phase, approximately when the percentage of doped cerium is between 20% and 30%. While the coercivity decreases directly with the increase in cerium content instead of being abnormal when there is no GB phase in magnets at all or the value of magnetocrystalline anisotropy or exchange integral is too large.

  4. Grain boundary phosphorus segregation under thermal aging in low alloy steels

    International Nuclear Information System (INIS)

    Nakata, Hayato; Fujii, Katsuhiko; Fukuya, Koji; Shibata, Masaaki; Kasada, Ryuta; Kimura, Akihiko

    2002-01-01

    Intergranular embrittlement due to grain boundary segregation of phosphorus is recognized as one of the potential degradation factors in irradiated reactor pressure vessel steels at high neutron fluences. In this study, investigations on low alloy steels thermally aged at 400-500degC were conducted to evaluate the correlation between phosphorus segregation and intergranular embrittlement. Phosphorus segregation determined using Auger electron spectroscopy increased after aging above 450degC and was in good agreement with the calculated value based on McLean model. No influence of thermal aging was observed in tensile properties. The ductile brittle transition temperature determined using 1/3 size charpy impact tests increased of 12degC after aging at 450degC for 3000 hours. These results indicated that there is a threshold level of phosphorus segregation for non-hardening embrittlement and that the level is around 0.14 for P/Fe peak ratio. (author)

  5. A visualization method for probing grain boundaries of single layer graphene via molecular beam epitaxy

    Science.gov (United States)

    Zhan, Linjie; Wan, Wen; Zhu, Zhenwei; Zhao, Zhijuan; Zhang, Zhenhan; Shih, Tien-Mo; Cai, Weiwei

    2017-07-01

    Graphene, a member of layered two-dimensional (2D) materials, possesses high carrier mobility, mechanical flexibility, and optical transparency, as well as enjoying a wide range of promising applications in electronics. Adopting the chemical vaporization deposition method, the majority of investigators have ubiquitously grown single layer graphene (SLG), which inevitably involves polycrystalline properties. Here we demonstrate a simple method for the direct visualization of arbitrarily large-size SLG domains by synthesizing one-hundred-nm-scale MoS2 single crystals via a high-vacuum molecular beam epitaxy process. The present study based on epitaxial growth provides a guide for probing the grain boundaries of various 2D materials and implements higher potentials for the next-generation electronic devices.

  6. Localized electronic states at grain boundaries on the surface of graphene and graphite

    DEFF Research Database (Denmark)

    Luican-Mayer, Adina; Barrios-Vargas, Jose E.; Falkenberg, Jesper Toft

    2016-01-01

    morphology affects the electronic properties is crucial for the development of applications such as flexible electronics, energy harvesting devices or sensors. We here report on atomic scale characterization of several GBs and on the structural-dependence of the localized electronic states in their vicinity....... Using low temperature scanning tunneling microscopy and spectroscopy, together with tight binding and ab initio numerical simulations we explore GBs on the surface of graphite and elucidate the interconnection between the local density of states and their atomic structure. We show that the electronic......ecent advances in large-scale synthesis of graphene and other 2D materials have underscored the importance of local defects such as dislocations and grain boundaries (GBs), and especially their tendency to alter the electronic properties of the material. Understanding how the polycrystalline...

  7. Energetics of Hydrogen Segregation to α-Fe Grain Boundaries for Modeling Stress Corrosion Cracking

    Science.gov (United States)

    Rajagopalan, M.; Adlakha, I.; Tschopp, M. A.; Solanki, K. N.

    2017-08-01

    The physics of embrittlement is dictated by the various interactions between the impurities/defects and the local structure in polycrystalline material systems. In this study, a physically motivated model that describes the degree of interaction of hydrogen (H) defects on the segregation behavior to α-Fe grain boundaries (GBs) is developed. Molecular statics simulations were performed to quantify the segregation behavior of 1-2 H atoms at various interstitial sites around the , , , and symmetric tilt GBs. The results provide insights into the concentration profile of hydrogen defects along different GBs. Furthermore, the model accurately links the intrinsic GB character by quantifying the segregation length scale for the individual GBs based on the segregation behavior of defects. Finally, the metrics provided in this work are essential to comprehensively understanding the effect of hydrogen on the macroscopic behavior of α-Fe.

  8. Atomistic simulations of grain boundary transformation under high pressures in MgO

    Science.gov (United States)

    Yokoi, T.; Yoshiya, M.

    2018-03-01

    This study focuses on transformation of grain boundary (GB) structures under high pressures up to 60 GPa by using a simulated annealing technique with molecular dynamics and lattice statics calculations for various symmetric tilt GBs (STGBs) of MgO. It is found that except for the Σ 3 (111) / [ 1 1 bar 0 ] that is a rather stable GB, all the STGBs studied transform into a metastable structure more than once at threshold pressures. In addition, the GBs with an open-core structure and small tilt angle are found to be more "flexible" to transform into different structures than the GBs with a dense structure. For polycrystalline MgO, therefore, GBs may also exhibit GB transformation under high pressures and flexible GBs may govern overall transformation and deformation. These findings also suggest that polycrystals sintered at high pressures consist of more pressure-resistant GBs than those at normal pressures.

  9. Simultaneous visualization of graphene grain boundaries and wrinkles with structural information by gold deposition.

    Science.gov (United States)

    Yu, Seong Uk; Park, Beomjin; Cho, Yeonchoo; Hyun, Seung; Kim, Jin Kon; Kim, Kwang S

    2014-08-26

    Although line defects such as grain boundaries (GBs) and wrinkles are unavoidable in graphene, difficulties in identification preclude studying their impact on electronic and mechanical properties. As previous methods focus on a single type of line defect, simultaneous measurements of both GBs and wrinkles with detailed structural information have not been reported. Here, we introduce effective visualization of both line defects by controlled gold deposition. Upon depositing gold on graphene, single lines and double lines of gold nanoparticles (NPs) are formed along GBs and wrinkles, respectively. Moreover, it is possible to analyze whether a GB is stitched or overlapped, whether a wrinkle is standing or folded, and the width of the standing collapsed wrinkle. Theoretical calculations show that the characteristic morphology of gold NPs is due to distinct binding energies of line defects, which are correlated to disrupting diffusion of NPs. Our approach could be further exploited to investigate the defect structures of other two-dimensional materials.

  10. Grain-boundary physics in polycrystalline CuInSe2 revisited: experiment and theory.

    Science.gov (United States)

    Yan, Yanfa; Noufi, R; Al-Jassim, M M

    2006-05-26

    Current studies have attributed the remarkable performance of polycrystalline CuInSe2 (CIS) to anomalous grain-boundary (GB) physics in CIS. The recent theory predicts that GBs in CIS are hole barriers, which prevent GB electrons from recombining. We examine the atomic structure and chemical composition of (112) GBs in Cu(In,Ga)Se2 (CIGS) using high-resolution Z-contrast imaging and nanoprobe x-ray energy-dispersive spectroscopy. We show that the theoretically predicted Cu-vacancy rows are not observed in (112) GBs in CIGS. Our first-principles modeling further reveals that the (112) GBs in CIS do not act as hole barriers. Our results suggest that the superior performance of polycrystalline CIS should not be explained solely by the GB behaviors.

  11. AC Josephson effect in YBa2Cu3O7-δ bicrystal grain boundary junctions

    International Nuclear Information System (INIS)

    Fischer, G.M.; Andreev, A.V.; Divin, Y.Ya.; Freltoft, T.; Mygind, J.; Pedersen, N.F.; Shen Yueqiang; Vase, P.

    1994-01-01

    The ac Josephson effect in YBa 2 Cu 3 O 7-δ bicrystal grain boundary junctions was studied in the temperature range from 4K to 90K. Junctions with widths from 0.2 to 50 μm were made on SrTiO 3 bicrystal substrates by laser ablation and e-beam lithography. The linewidth of the Josephson oscillations is derived from the shape of the dc voltage response to low-intensity, f = 70 GHz radiation at voltages V ≅ (h/2e) f, assuming the RSJ model. The effect of the size on the Josephson behavior of this type of high-T c junctions was studied. Close to T c the linewidth of the Josephson oscillations was shown to be determined by thermal fluctuations. (orig.)

  12. Texture, local misorientation, grain boundary and recrystallization fraction in pipeline steels related to hydrogen induced cracking

    Energy Technology Data Exchange (ETDEWEB)

    Mohtadi-Bonab, M.A., E-mail: m.mohtadi@usask.ca; Eskandari, M.; Szpunar, J.A.

    2015-01-03

    In the present study, API X60 and X60SS pipeline steels were cathodically charged by hydrogen for 8 h using 0.2 M sulfuric acid and 3 g/l ammonium thiocyanate. After charging, SEM observations showed that the hydrogen induced cracking (HIC) appeared at the center of cross section in the X60 specimen. However, HIC did not appear in the X60SS steel. Therefore, electron backscatter diffraction (EBSD) technique was used to analyze the center of cross section of as-received X60SS, X60 and HIC tested X60 specimens. The results showed that the HIC crack not only can propagate through 〈100〉||ND oriented grains but also its growth may happen in various orientations. In HIC tested X60 specimen, an accumulation of low angle grain boundaries around the crack path documented that full recrystallization was not achieved during hot rolling. Kernel Average Misorientaion (KAM) histogram illustrated that the deformation is more concentrated in as-received and HIC tested X60 specimens rather than in as-received X60SS specimen. Moreover, the concentration of coincidence site lattice (CSL) boundary in HIC tested X60 specimen was very low compared with other samples. The recrystallization area fraction in X60SS steel was very high. This high amount of recrystallization fraction with no stored energy is one of the main reasons for high HIC resistance of this steel to HIC. The orientation distribution function (ODF) of the recrystallized, substructured and deformed fractions in as-received X60SS and X60 steel showed relative close orientations in both as-received specimens.

  13. Recombination in Perovskite Solar Cells: Significance of Grain Boundaries, Interface Traps, and Defect Ions.

    Science.gov (United States)

    Sherkar, Tejas S; Momblona, Cristina; Gil-Escrig, Lidón; Ávila, Jorge; Sessolo, Michele; Bolink, Henk J; Koster, L Jan Anton

    2017-05-12

    Trap-assisted recombination, despite being lower as compared with traditional inorganic solar cells, is still the dominant recombination mechanism in perovskite solar cells (PSCs) and limits their efficiency. We investigate the attributes of the primary trap-assisted recombination channels (grain boundaries and interfaces) and their correlation to defect ions in PSCs. We achieve this by using a validated device model to fit the simulations to the experimental data of efficient vacuum-deposited p-i-n and n-i-p CH 3 NH 3 PbI 3 solar cells, including the light intensity dependence of the open-circuit voltage and fill factor. We find that, despite the presence of traps at interfaces and grain boundaries (GBs), their neutral (when filled with photogenerated charges) disposition along with the long-lived nature of holes leads to the high performance of PSCs. The sign of the traps (when filled) is of little importance in efficient solar cells with compact morphologies (fused GBs, low trap density). On the other hand, solar cells with noncompact morphologies (open GBs, high trap density) are sensitive to the sign of the traps and hence to the cell preparation methods. Even in the presence of traps at GBs, trap-assisted recombination at interfaces (between the transport layers and the perovskite) is the dominant loss mechanism. We find a direct correlation between the density of traps, the density of mobile ionic defects, and the degree of hysteresis observed in the current-voltage ( J - V ) characteristics. The presence of defect states or mobile ions not only limits the device performance but also plays a role in the J - V hysteresis.

  14. Grain boundary defects initiation at the outer surface of dissimilar welds: corrosion mechanism studies

    International Nuclear Information System (INIS)

    De Bouvier, O.; Yrieix, B.

    1995-11-01

    Dissimilar welds located on the primary coolant system of the French PWR I plants exhibit grain boundary defects in the true austenitic zones of the first buttering layer. If grain boundaries reach the interface, they can extend to the martensitic band. Those defects are filled with compact oxides. In addition, the ferritic base metal presents some pits along the interface. Nowadays, three mechanisms are proposed to explain the initiation of those defects: stress corrosion cracking, intergranular corrosion and high temperature intergranular oxidation. This paper is dealing with the study of the mechanisms involved in the corrosion phenomenon. Intergranular corrosion tests performed on different materials show that only the first buttering layer, even with some δ ferrite, is sensitized. The results of stress corrosion cracking tests in water solutions show that intergranular cracking is possible on a bulk material representative of the first buttering layer. It is unlikely on actual dissimilar welds where the ferritic base metal protects the first austenitic layer by galvanic coupling. Therefore, the stress corrosion cracking assumption cannot explain the initiation of the defects in aqueous environment. The results of the investigations and of the corrosion studies led to the conclusion that the atmosphere could be the only possible aggressive environment. This conclusion is based on natural atmospheric exposure and accelerated corrosion tests carried out with SO 2 additions in controlled atmosphere. They both induce a severe intergranular corrosion on true sensitized austenitic materials. This corrosion studies cannot conclude definitively on the causes of the defect initiation on field, but they show that the atmospheric corrosion could produce intergranular attacks in the pure austenitic zones of the first buttering layer of the dissimilar welds and that this corrosion is stress assisted. (author). 1 ref., 6 figs., 4 tabs

  15. Thermodynamic effect of elastic stress on grain boundary segregation of phosphorus in a low alloy steel

    International Nuclear Information System (INIS)

    Zheng, Lei; Lejček, Pavel; Song, Shenhua; Schmitz, Guido; Meng, Ye

    2015-01-01

    Grain boundary (GB) segregation of P in 2.25Cr1Mo steel induced by elastic stress shows that the P equilibrium concentration, after reaching the non-equilibrium concentration maximum at critical time, returns to its initial thermal equilibrium level. This finding confirms the interesting phenomenon that the effect of elastic stress on GB segregation of P is significant in kinetics while slight in thermodynamics. Through extending the “pressure” in classical theory of chemical potential to the “elastic stress”, the thermodynamic effect of elastic stress on GB segregation is studied, and the relationship between elastic stress and segregation Gibbs energy is formulated. The formulas reveal that the difference in the segregation Gibbs energy between the elastically-stressed and non-stressed states depends on the excess molar volume of GB segregation and the magnitude of elastic stress. Model calculations in segregation Gibbs energy confirm that the effect of elastic stress on the thermodynamics of equilibrium GB segregation is slight, and the theoretical analyses considerably agree with the experimental results. The confirmation indicates that the nature of the thermodynamic effect is well captured. - Highlights: • GB segregation of P after stress aging returns to its initial thermal equilibrium level. • Relationship between elastic stress and segregation energy is formulated. • Thermodynamic effect relies on excess molar volume and magnitude of elastic stress. • Effect of elastic stress on Gibbs energy of GB segregation is estimated to be slight. • Complete theory of the effect of elastic stress on grain boundary segregation is setup

  16. Influence of grain boundary connectivity on the trapped magnetic flux of multi-seeded bulk superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Deng, Z., E-mail: zgdeng@gmail.com [Laboratory of Applied Physics, Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, Tokyo 135-8533 (Japan); Miki, M.; Felder, B.; Tsuzuki, K.; Shinohara, N.; Hara, S.; Uetake, T.; Izumi, M. [Laboratory of Applied Physics, Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, Tokyo 135-8533 (Japan)

    2011-09-15

    Four different performance multi-seeded YBCO bulks as representatives. A coupling ratio to reflect the coupling quality of GBs inside multi-seeded bulks. An averaged trapped magnetic flux density parameter was introduced. The top-seeded melt-growth process with multi-seeding technique provides a promising way to fabricate large-sized bulk superconductors in an economical way. To understand the essential characteristics of the multi-seeded bulks, the paper reports the influence of the grain boundary (GB) coupling or connectivity on the total trapped magnetic flux. The coupling ratio, the lowest trapped flux density in the GB area to the averaged top value of the two neighboring peak trapped fields, is introduced to reflect the coupling quality of GBs inside a multi-seeded bulk. By the trapped flux density measurement of four different performance multi-seeded YBCO bulk samples as representatives, it was found that the GB coupling plays an important role for the improvement of the total trapped magnetic flux; moreover, somewhat more significant than the widely used parameter of the peak trapped fields to evaluate the physical performance of bulk samples. This characteristic is different with the case of the well-grown single-grain bulks.

  17. Influence of grain boundary connectivity on the trapped magnetic flux of multi-seeded bulk superconductors

    Science.gov (United States)

    Deng, Z.; Miki, M.; Felder, B.; Tsuzuki, K.; Shinohara, N.; Hara, S.; Uetake, T.; Izumi, M.

    2011-09-01

    The top-seeded melt-growth process with multi-seeding technique provides a promising way to fabricate large-sized bulk superconductors in an economical way. To understand the essential characteristics of the multi-seeded bulks, the paper reports the influence of the grain boundary (GB) coupling or connectivity on the total trapped magnetic flux. The coupling ratio, the lowest trapped flux density in the GB area to the averaged top value of the two neighboring peak trapped fields, is introduced to reflect the coupling quality of GBs inside a multi-seeded bulk. By the trapped flux density measurement of four different performance multi-seeded YBCO bulk samples as representatives, it was found that the GB coupling plays an important role for the improvement of the total trapped magnetic flux; moreover, somewhat more significant than the widely used parameter of the peak trapped fields to evaluate the physical performance of bulk samples. This characteristic is different with the case of the well-grown single-grain bulks.

  18. Deformation effects on the development of grain boundary chronium depletion (sensitization) in type 316 austenitic stainless steels

    International Nuclear Information System (INIS)

    Atteridge, D.G.; Wood, W.E.; Advani, A.H.; Bruemmer, S.M.

    1990-01-01

    Deformation induces an acceleration in the kinetics and reduction in the thermodynamic barrier to carbide precipitation and grain boundary chromium depletion (GBCD) development of a high carbon Type 316 stainless steel (SS). This was observed in a study on strain effects on GBCD (or sensitization) development in the range of 575 degree C to 775 degree C. Grain boundary chromium depletion behavior of SS was examined using the indirect electrochemical potentiokinetic reactivation (EPR) test and supported by studies on carbide precipitation using transmission electron microscopy (TEM). 99 refs., 84 figs., 9 tabs

  19. Orientation dependence of grain-boundary energy in metals in the view of a pseudoheterophase dislocation core model

    International Nuclear Information System (INIS)

    Missol, W.

    1976-01-01

    A new dislocation model for symmetric tilt grain boundaries was developed as a basis for deriving the quantitative dependence of grain-boundary energy upon misorientation angle in the form of an expression similar to that given by Read and Shockley [Phys. Rev. 78: 275(1950)]. The range of applicability of this equation was extended to over 20 degrees. A comparison of theory and experiment was made for Bi, Ag, Cu, and Fe--Si 3 percent in the teen-degree range of misorientation angles and for Au, α-Fe, Mo, and W in the high-angle range

  20. Influence of orientation mismatch on charge transport across grain boundaries in tri-isopropylsilylethynyl (TIPS) pentacene thin films.

    Science.gov (United States)

    Steiner, Florian; Poelking, Carl; Niedzialek, Dorota; Andrienko, Denis; Nelson, Jenny

    2017-05-03

    We present a multi-scale model for charge transport across grain boundaries in molecular electronic materials that incorporates packing disorder, electrostatic and polarisation effects. We choose quasi two-dimensional films of tri-isopropylsilylethynyl pentacene (TIPS-P) as a model system representative of technologically relevant crystalline organic semiconductors. We use atomistic molecular dynamics, with a force-field specific for TIPS-P, to generate and equilibrate polycrystalline two-dimensional thin films. The energy landscape is obtained by calculating contributions from electrostatic interactions and polarization. The variation in these contributions leads to energetic barriers between grains. Subsequently, charge transport is simulated using a kinetic Monte-Carlo algorithm. Two-grain systems with varied mutual orientation are studied. We find relatively little effect of long grain boundaries due to the presence of low impedance pathways. However, effects could be more pronounced for systems with limited inter-grain contact areas. Furthermore, we present a lattice model to generalize the model for small molecular systems. In the general case, depending on molecular architecture and packing, grain boundaries can result in interfacial energy barriers, traps or a combination of both with qualitatively different effects on charge transport.

  1. Solute grain boundary segregation during high temperature plastic deformation in a Cr-Mo low alloy steel

    International Nuclear Information System (INIS)

    Chen, X.-M.; Song, S.-H.; Weng, L.-Q.; Liu, S.-J.

    2011-01-01

    Highlights: → The segregation of P and Mo is evidently enhanced by plastic deformation. → The boundary concentrations of P and Mo increase with increasing strain. → A model with consideration of site competition in grain boundary segregation in a ternary system is developed. → Model predictions show a reasonable agreement with the observations. - Abstract: Grain boundary segregation of Cr, Mo and P to austenite grain boundaries in a P-doped 1Cr0.5Mo steel is examined using field emission gun scanning transmission electron microscopy for the specimens undeformed and deformed by 10% with a strain rate of 2 x 10 -3 s -1 at 900 deg. C, and subsequently water quenched to room temperature. Before deformation, there is some segregation for Mo and P, but the segregation is considerably increased after deformation. The segregation of Cr is very small and there is no apparent difference between the undeformed and deformed specimens. Since the thermal equilibrium segregation has been attained prior to deformation, the segregation produced during deformation has a non-equilibrium characteristic. A theoretical model with consideration of site competition in grain boundary segregation between two solutes in a ternary alloy is developed to explain the experimental results. Model predictions are made, which show a reasonable agreement with the observations.

  2. The Role of Pore-Formers on Grain Interior and Grain Boundary Conductivity in Tape-Cast Porous Sheets for Electrochemical Flue Gas Purification

    DEFF Research Database (Denmark)

    Schmidt, Cristine Grings; Andersen, Kjeld Bøhm; Stamate, Eugen

    2018-01-01

    Ce0.9Gd0.1O1.95 (CGO) electrolytes for electrochemical flue gas purification were fabricated by means of tape casting with different types, shapes and sizes of pore-formers. The sintered bodies were characterized with electrochemical impedance spectroscopy, to investigate the role of the different...... pore-formers on the electrochemical properties of the cast tapes. A strong effect of the different pore-formers on the conductivity (both grain interior and grain boundary conductivities) was observed. In addition, the conductivity data were also correlated with previously obtained gas permeability...

  3. Shear-Induced Brittle Failure along Grain Boundaries in Boron Carbide.

    Science.gov (United States)

    Yang, Xiaokun; Coleman, Shawn P; Lasalvia, Jerry C; Goddard, William A; An, Qi

    2018-02-07

    The role that grain boundaries (GBs) can play on mechanical properties has been studied extensively for metals and alloys. However, for covalent solids such as boron carbide (B 4 C), the role of GB on the inelastic response to applied stresses is not well established. We consider here the unusual ceramic, boron carbide (B 4 C), which is very hard and lightweight but exhibits brittle impact behavior. We used quantum mechanics (QM) simulations to examine the mechanical response in atomistic structures that model GBs in B 4 C under pure shear and also with biaxial shear deformation that mimics indentation stress conditions. We carried out these studies for two simple GB models including also the effect of adding Fe atoms (possible sintering aid and/or impurity) to the GB. We found that the critical shear stresses of these GB models are much lower than that for crystalline and twinned B 4 C. The two GB models lead to different interfacial energies. The higher interfacial energy at the GB only slightly decreases the critical shear stress but dramatically increases the critical failure strain. Doping the GB with Fe decreases the critical shear stress of at the boundary by 14% under pure shear deformation. In all GBs studied here, failure arises from deconstructing the icosahedra within the GB region under shear deformation. We find that Fe dopant interacts with icosahedra at the GB to facilitate this deconstruction of icosahedra. These results provide significant insight into designing polycrystalline B 4 C with improved strength and ductility.

  4. Grain boundaries in bcc-Fe: a density-functional theory and tight-binding study

    Science.gov (United States)

    Wang, Jingliang; Madsen, Georg K. H.; Drautz, Ralf

    2018-02-01

    Grain boundaries (GBs) have a significant influence on material properties. In the present paper, we calculate the energies of eleven low-Σ ({{Σ }}≤slant 13) symmetrical tilt GBs and two twist GBs in ferromagnetic bcc iron using first-principles density functional theory (DFT) calculations. The results demonstrate the importance of a sufficient sampling of initial rigid body translations in all three directions. We show that the relative GB energies can be explained by the miscoordination of atoms at the GB region. While the main features of the studied GB structures were captured by previous empirical interatomic potential calculations, it is shown that the absolute values of GB energies calculated were substantially underestimated. Based on DFT-calculated GB structures and energies, we construct a new d-band orthogonal tight-binding (TB) model for bcc iron. The TB model is validated by its predictive power on all the studied GBs. We apply the TB model to block boundaries in lath martensite and demonstrate that the experimentally observed GB character distribution can be explained from the viewpoint of interface energy.

  5. Precipitation of grain boundary α in a laser deposited compositionally graded Ti-8Al-xV alloy - an orientation microscopy study

    International Nuclear Information System (INIS)

    Banerjee, R.; Bhattacharyya, D.; Collins, P.C.; Viswanathan, G.B.; Fraser, H.L.

    2004-01-01

    A graded ternary Ti-8Al-xV alloy (all compositions in wt%) has been deposited using the laser engineered net-shaping (LENS TM ) process. A compositional gradient in the alloy, from binary Ti-8Al to Ti-8Al-20V, has been achieved within a length of ∼25 mm. The feedstock used for depositing the graded alloy consisted of elemental Ti, Al, and V powders. Due to the columnar growth morphology of the β grains in these LENS TM deposited Ti alloys, the same prior β grain boundary often extends across lengths ∼10 mm. Using orientation microscopy techniques in a scanning electron microscope, the crystallography of precipitation of grain boundary α across the same boundary with changing composition has been investigated in detail. It was observed that while most grain boundary α precipitates maintain a Burgers or near-Burgers orientation relationship with only one of the β grains, a few of these precipitates develop a Burgers orientation relationship with the other β grain. In some rare instances, the grain boundary α did not develop a Burgers or near-Burgers orientation relationship with either β grains. Interestingly, in many cases while the grain boundary α maintained Burgers relationship with one of the β grains, precipitates of two different variants decorated the boundary, in a near-alternate fashion

  6. Meso-microstructural computational simulation of the hydrogen permeation test to calculate intergranular, grain boundary and effective diffusivities

    International Nuclear Information System (INIS)

    Jothi, S.; Winzer, N.; Croft, T.N.; Brown, S.G.R.

    2015-01-01

    Highlights: • Characterized polycrystalline nickel microstructure using EBSD analysis. • Development meso-microstructural model based on real microstructure. • Calculated effective diffusivity using experimental electrochemical permeation test. • Calculated intergranular diffusivity of hydrogen using computational FE simulation. • Validated the calculated computation simulation results with experimental results. - Abstract: Hydrogen induced intergranular embrittlement has been identified as a cause of failure of aerospace components such as combustion chambers made from electrodeposited polycrystalline nickel. Accurate computational analysis of this process requires knowledge of the differential in hydrogen transport in the intergranular and intragranular regions. The effective diffusion coefficient of hydrogen may be measured experimentally, though experimental measurement of the intergranular grain boundary diffusion coefficient of hydrogen requires significant effort. Therefore an approach to calculate the intergranular GB hydrogen diffusivity using finite element analysis was developed. The effective diffusivity of hydrogen in polycrystalline nickel was measured using electrochemical permeation tests. Data from electron backscatter diffraction measurements were used to construct microstructural representative volume elements including details of grain size and shape and volume fraction of grains and grain boundaries. A Python optimization code has been developed for the ABAQUS environment to calculate the unknown grain boundary diffusivity

  7. Meso-microstructural computational simulation of the hydrogen permeation test to calculate intergranular, grain boundary and effective diffusivities

    Energy Technology Data Exchange (ETDEWEB)

    Jothi, S., E-mail: s.jothi@swansea.ac.uk [College of Engineering, Swansea University, Singleton Park, Swansea SA2 8PP (United Kingdom); Winzer, N. [Fraunhofer Institute for Mechanics of Materials IWM, Wöhlerstraße 11, 79108 Freiburg (Germany); Croft, T.N.; Brown, S.G.R. [College of Engineering, Swansea University, Singleton Park, Swansea SA2 8PP (United Kingdom)

    2015-10-05

    Highlights: • Characterized polycrystalline nickel microstructure using EBSD analysis. • Development meso-microstructural model based on real microstructure. • Calculated effective diffusivity using experimental electrochemical permeation test. • Calculated intergranular diffusivity of hydrogen using computational FE simulation. • Validated the calculated computation simulation results with experimental results. - Abstract: Hydrogen induced intergranular embrittlement has been identified as a cause of failure of aerospace components such as combustion chambers made from electrodeposited polycrystalline nickel. Accurate computational analysis of this process requires knowledge of the differential in hydrogen transport in the intergranular and intragranular regions. The effective diffusion coefficient of hydrogen may be measured experimentally, though experimental measurement of the intergranular grain boundary diffusion coefficient of hydrogen requires significant effort. Therefore an approach to calculate the intergranular GB hydrogen diffusivity using finite element analysis was developed. The effective diffusivity of hydrogen in polycrystalline nickel was measured using electrochemical permeation tests. Data from electron backscatter diffraction measurements were used to construct microstructural representative volume elements including details of grain size and shape and volume fraction of grains and grain boundaries. A Python optimization code has been developed for the ABAQUS environment to calculate the unknown grain boundary diffusivity.

  8. Observation of distinct, temperature dependent flux noise near bicrystal grain boundaries in YBa2Cu3O7-x films

    DEFF Research Database (Denmark)

    Bukh, K. R.; Jacobsen, Claus Schelde; Hansen, Jørn Bindslev

    2000-01-01

    The characteristics of the magnetic flux noise in high temperature superconducting thin-films of yttrium-barium-copper-oxide (YBa2Cu3O7) in the vicinity of artificial grain boundaries have been studied by means of a low critical temperature superconducting quantum interference device (SQUID...

  9. Formation of multiple stoichiometric phases in binary systems by combined bulk and grain boundary diffusion: Experiments and model

    Czech Academy of Sciences Publication Activity Database

    Svoboda, Jiří; Fischer, F. D.; Schillinger, W.

    2013-01-01

    Roč. 61, č. 1 (2013), s. 32-39 ISSN 1359-6454 R&D Projects: GA ČR GAP204/10/1784 Institutional support: RVO:68081723 Keywords : Bulk diffusion * Thermodynamic modeling * Intermetallic phases * Grain-boundary diffusion Subject RIV: BJ - Thermodynamics Impact factor: 3.940, year: 2013

  10. Prediction of enthalpy and entropy of solute segregation at individua grain boundaries of α-iron and ferrite steels

    Czech Academy of Sciences Publication Activity Database

    Lejček, Pavel; Hofmann, S.; Janovec, J.

    2007-01-01

    Roč. 462, - (2007), s. 76-85 ISSN 0921-5093 R&D Projects: GA ČR(CZ) GA106/05/0134 Institutional research plan: CEZ:AV0Z10100520 Keywords : segregation * grain boundaries * enthalpy/entropy relationship * α-iron * prediction Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.457, year: 2007

  11. Effect of Grain Boundary Character Distribution on the Impact Toughness of 410NiMo Weld Metal

    DEFF Research Database (Denmark)

    Divya, M.; Das, Chitta Ranjan; Chowdhury, Sandip Ghosh

    2016-01-01

    Grain boundary character distributions in 410NiMo weld metal were studied in the as-welded, first-stage, and second-stage postweld heat treatment (PWHT) conditions, and these were correlated with the Charpy-V impact toughness values of the material. The high impact toughness values in the weld...

  12. Dynamics of ordering in highly degenerate models with anisotropic grain-boundary potential: Effects of temperature and vortex formation

    DEFF Research Database (Denmark)

    Jeppesen, Claus; Flyvbjerg, Henrik; Mouritsen, Ole G.

    1989-01-01

    -boundary potential on triangular lattices—essentially clock models, except that the potential is not a cosine, but a sine function of the angle between neighboring grain orientations. For not too small Q, these models display two thermally driven phase transitions, one which takes the system from a low...

  13. Effects of Grain Boundaries and Dislocation Cell Walls on Void Nucleation and Growth in Aluminium during Fast Neutron Irradiation

    DEFF Research Database (Denmark)

    Horsewell, Andy; Rahman, F. A.; Singh, Bachu Narain

    1983-01-01

    High purity aluminium irradiated to fluences between 2 multiplied by 10**2**1 and 1 multiplied by 10**2**4 n. m** minus **2 (E greater than 1 Mev) at 120 degree C has been investigated by TEM. A void denuded zone is seen both at grain boundaries and dislocation cell walls. Enhanced void formation...

  14. Investigations on grain boundary segregation energy of phosphorus in 12Cr1MoV steel under elastic stress

    Czech Academy of Sciences Publication Activity Database

    Zheng, L.; Fu, Y.; Lejček, Pavel; Song, S.; Schmitz, G.; Meng, Y.

    2016-01-01

    Roč. 18, č. 4 (2016), 506-510 ISSN 1438-1656 R&D Projects: GA ČR GAP108/12/0144 Institutional support: RVO:68378271 Keywords : grain boundary segregation, * stress effect, * phosphorus, * steel Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.319, year: 2016

  15. Effect of Grain Orientation and Boundary Distributions on Hydrogen-Induced Cracking in Low-Carbon-Content Steels

    Science.gov (United States)

    Masoumi, Mohammad; Coelho, Hana Livia Frota; Tavares, Sérgio Souto Maior; Silva, Cleiton Carvalho; de Abreu, Hamilton Ferreira Gomes

    2017-08-01

    Hydrogen-induced cracking (HIC) causes considerable economic losses in a wide range of steels exposed to corrosive environments. The effect of crystallographic texture and grain boundary distributions tailored by rolling at 850 °C in three different steels with a body-centered cube structure was investigated on HIC resistance. The x-ray and electron backscattered diffraction techniques were used to characterize texture evolutions during the rolling process. The findings revealed a significant improvement against HIC based on texture engineering. In addition, increasing the number of {111} and {110} grains, associated with minimizing the number of {001} grains in warm-rolled samples, reduced HIC susceptibility. Moreover, the results showed that boundaries associated with low {hkl} indexing and denser packing planes had more resistance against crack propagation.

  16. Effect of Silicon application on Morpho-physiological Characteristics, Grain Yield and Nutrient Content of Bread Wheat under Water Stress Conditions

    Directory of Open Access Journals (Sweden)

    A. Karmollachaab

    2015-03-01

    Full Text Available In order to investigate the effect of silicon application on some physiological characteristics, yield and yield components, and grain mineral contents of bread wheat (Triticum aestivum under water stress condition, an experiment was conducted in Ramin Agriculture and Natural Resources University, Khuzestan, in 2012. The experiment was arranged in split-plots design in RCBD (Completely Randomized Blocks Design with three replications. Treatments consisted of drought stress (irrigation after 25, 50 and 75% depletion of Available Water Content in main plots and silicon (0, 10, 20 and 30 Kg Si ha-1 arranged in sub-plots. Results showed that the effect of drought stress was significant on most traits and led to the increase of electrolyte leakage (EL, cuticular wax, leaf and grain silicon content and grain nitrogen content. But drought led to negative impacts on grain yield and its components, and leaf potassium content, i.e. moderate and severe stresses reduced yield by 17% and 38% compared to control, respectively. Effect of silicon application was significant on all traits except for spike per square meter. Silicon had the greatest impact on EL and led to 35% decrease in this trait. Also, silicon led to increase in leaf and grain silicon contents and grain K content and grain yield and yield components, when applied at 30 kg ha-1. Generally, application of 30 kg ha-1 of silicon led to 6 and 14% increases of grain yield at the presence of moderate and severe drought stresses, respectively. Thus, given the abundance of silicon it can be used as an ameliorating element for planting bread wheat in drought-prone conditions.

  17. Impact of Mismatch Angle on Electronic Transport Across Grain Boundaries and Interfaces in 2D Materials.

    Science.gov (United States)

    Majee, Arnab K; Foss, Cameron J; Aksamija, Zlatan

    2017-11-29

    We study the impact of grain boundaries (GB) and misorientation angles between grains on electronic transport in 2-dimensional materials. Here we have developed a numerical model based on the first-principles electronic bandstructure calculations in conjunction with a method which computes electron transmission coefficients from simultaneous conservation of energy and momentum at the interface to essentially evaluate GB/interface resistance in a Landauer formalism. We find that the resistance across graphene GBs vary over a wide range depending on misorientation angles and type of GBs, starting from 53 Ω μm for low-mismatch angles in twin (symmetric) GBs to about 10 20  Ω μm for 21° mismatch in tilt (asymmetric) GBs. On the other hand, misorientation angles have weak influence on the resistance across MoS 2 GBs, ranging from about 130 Ω μm for low mismatch angles to about 6000 Ω μm for 21°. The interface resistance across graphene-MoS 2 heterojunctions also exhibits a strong dependence on misorientation angles with resistance values ranging from about 100 Ω μm for low-mismatch angles in Class-I (symmetric) interfaces to 10 15  Ω μm for 14° mismatch in Class-II (asymmetric) interfaces. Overall, symmetric homo/heterojunctions exhibit a weak dependence on misorientation angles, while in MoS 2 both symmetric and asymmetric GBs show a gradual dependence on mismatch angles.

  18. Computational Capabilities for Predictions of Interactions at the Grain Boundary of Refractory Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Sengupta, Debasis [CFD Research, Huntsville, AL (United States); Kwak, Shaun [CFD Research, Huntsville, AL (United States); Vasenkov, Alex [CFD Research, Huntsville, AL (United States); Shin, Yun Kyung [Pennsylvania State Univ., University Park, PA (United States); Duin, Adri van [Pennsylvania State Univ., University Park, PA (United States)

    2014-12-01

    New high performance refractory alloys are critically required for improving efficiency and decreasing CO2 emissions of fossil energy systems. The development of these materials remains slow because it is driven by a trial-and-error experimental approach and lacks a rational design approach. Atomistic Molecular Dynamic (MD) design has the potential to accelerate this development through the prediction of mechanical properties and corrosion resistance of new materials. The success of MD simulations depends critically on the fidelity of interatomic potentials. This project, in collaboration with Penn State, has focused on developing and validating high quality quantum mechanics based reactive potentials, ReaxFF, for Ni-Fe-Al-Cr-O-S system. A larger number of accurate density functional theory (DFT) calculations were performed to generate data for parameterizing the ReaxFF potentials. These potentials were then used in molecular dynamics (MD) and molecular dynamics-Monte Carlo (MD-MC) for much larger system to study for which DFT calculation would be prohibitively expensive, and to understand a number of chemical phenomena Ni-Fe-Al-Cr-O-S based alloy systems . These include catalytic oxidation of butane on clean Cr2O3 and pyrite/Cr2O3, interfacial reaction between Cr2O3 (refractory material) and Al2O3 (slag), cohesive strength of at the grain boundary of S-enriched Cr compared to bulk Cr and Ssegregation study in Al, Al2O3, Cr and Cr2O3 with a grain structure. The developed quantum based ReaxFF potential are available from the authors upon request. During this project, a number of papers were published in peer-reviewed journals. In addition, several conference presentations were made.

  19. Stress-induced non-equilibrium grain boundary segregation of phosphorus in a Cr-Mo low alloy steel

    International Nuclear Information System (INIS)

    Song, S.-H.; Wu, J.; Wang, D.-Y.; Weng, L.-Q.; Zheng, L.

    2006-01-01

    Grain boundary segregation of phosphorus under a 40 MPa tensile stress at 520 deg. C in a 0.025 wt.% P-doped 2.25Cr1Mo steel, which has already been thermally equilibrated, is examined using Auger electron spectroscopy. The segregation of phosphorus during stress-ageing has a non-equilibrium characteristic, i.e. it is non-equilibrium segregation. The segregation level first increases with increasing stress-ageing time until about 0.5 h and then diminishes with further increasing stress-ageing time, leading the boundary concentration of phosphorus to return to its thermal equilibrium value after ageing for about 15 h. Therefore, the critical time for this non-equilibrium grain boundary segregation of phosphorus is about 0.5 h at which the segregation is peaked. At this critical time, the boundary concentration of phosphorus is about 20.5 at.%, which is about 4.5 at.% higher than its thermal equilibrium level. Xu's kinetic model for stress-induced grain boundary segregation [T.D. Xu, Philos. Mag. 83 (2003) 889-899; T.D. Xu, B.-Y. Cheng, Prog. Mater. Sci. 49 (2) (2004) 109-208] is used to analyse the experimental results, demonstrating that the measured data may be well simulated by the model

  20. Molecular dynamics study of the role of symmetric tilt grain boundaries on the helium distribution in nickel

    Science.gov (United States)

    Torres, E.; Pencer, J.

    2018-04-01

    Helium impurities, from either direct implantation or transmutation reactions, have been associated with embrittlement in nickel-based alloys. Helium has very low solubility in nickel, and has been found to aggregate at lattice defects such as vacancies, dislocations, and grain boundaries. The retention and precipitation of helium in nickel-based alloys have deleterious effects on the material mechanical properties. However, the underlying mechanisms that lead to helium effects in the host metal are not fully understood. In the present work, we investigate the role of symmetric tilt grain boundary (STGB) structures on the distribution of helium in nickel using molecular dynamics simulations. We investigate the family of STGBs specific to the 〈 110 〉 tilt axis. The present results indicate that accumulation of helium at the grain boundary may be modulated by details of grain boundary geometry. A plausible correlation between the grain boundary energy and misorientation with the accumulation and mobility of helium is proposed. Small clusters with up to 6 helium atoms show significant interstitial mobility in the nickel bulk, but also become sites for nucleation and grow of more stable helium clusters. High-energy GBs are found mainly populated with small helium clusters. The high mobility of small clusters along the GBs indicates the role of these GBs as fast two-dimensional channels for diffusion. In contrast, the accumulation of helium in large helium clusters at low-energy STGB creates a favorable environment for the formation of large helium bubbles, indicating a potential role for low-energy STGB in promoting helium-induced GB embrittlement.

  1. Surface morphology and grain analysis of successively industrially grown amorphous hydrogenated carbon films (a-C:H) on silicon

    Science.gov (United States)

    Catena, Alberto; McJunkin, Thomas; Agnello, Simonpietro; Gelardi, Franco M.; Wehner, Stefan; Fischer, Christian B.

    2015-08-01

    Silicon (1 0 0) has been gradually covered by amorphous hydrogenated carbon (a-C:H) films via an industrial process. Two types of these diamond-like carbon (DLC) coatings, one more flexible (f-DLC) and one more robust (r-DLC), have been investigated. Both types have been grown by a radio frequency plasma-enhanced chemical vapor deposition (RF-PECVD) technique with acetylene plasma. Surface morphologies have been studied in detail by atomic force microscopy (AFM) and Raman spectroscopy has been used to investigate the DLC structure. Both types appeared to have very similar morphology and sp2 carbon arrangement. The average height and area for single grains have been analyzed for all depositions. A random distribution of grain heights was found for both types. The individual grain structures between the f- and r-type revealed differences: the shape for the f-DLC grains is steeper than for the r-DLC grains. By correlating the average grain heights to the average grain areas for all depositions a limited region is identified, suggesting a certain regularity during the DLC deposition mechanisms that confines both values. A growth of the sp2 carbon entities for high r-DLC depositions is revealed and connected to a structural rearrangement of carbon atom hybridizations and hydrogen content in the DLC structure.

  2. Grain boundary corrosion and alteration phase formation during the oxidative dissolution of UO{sub 2} pellets

    Energy Technology Data Exchange (ETDEWEB)

    Wronkiewicz, D.J.; Buck, E.C.; Bates, J.K.

    1996-12-31

    Alteration behavior of UO{sub 2} pellets following reaction under unsaturated drip-test conditions at 90 C for up to 10 years was examined by solid phase and leachate analyses. Sample reactions were characterized by preferential dissolution of grain boundaries between the original press-sintered UO{sub 2} granules comprising the samples, development of a polygonal network of open channels along the intergrain boundaries, and spallation of surface granules that had undergone severe grain boundary corrosion. The development of a dense mat of alteration phases after 2 years of reaction trapped loose granules, resulting in reduced rates of particulate U release. The paragenetic sequence of alteration phases that formed on the present samples was similar to that observed in surficial weathering zones of natural uraninite (UO{sub 2}) deposits, with alkali and alkaline earth uranyl silicates representing the long-term solubility-limiting phases for U in both systems.

  3. Spectral response of a polycrystalline silicon solar cell

    International Nuclear Information System (INIS)

    Ba, B.; Kane, M.

    1994-10-01

    A theoretical study of the spectral response of a polycrystalline silicon n-p junction solar cell is presented. The case of a fibrously oriented grain structure, involving grain boundary recombination velocity and grain size effects is discussed. The contribution of the base region on the internal quantum efficiency Q int is computed for different grain sizes and grain boundary recombination velocities in order to examine their influence. Suggestions are also made for the determination of base diffusion length in polycrystalline silicon solar cells using the spectral response method. (author). 15 refs, 4 figs

  4. Gap States at Low-Angle Grain Boundaries in Monolayer Tungsten Diselenide

    KAUST Repository

    Huang, Yu Li

    2016-05-03

    Two-dimensional (2D) transition metal dichalcogenides (TMDs) have revealed many novel properties of interest to future device applications. In particular, the presence of grain boundaries (GBs) can significantly influence the material properties of 2D TMDs. However, direct characterization of the electronic properties of the GB defects at the atomic scale remains extremely challenging. In this study, we employ scanning tunneling microscopy and spectroscopy to investigate the atomic and electronic structure of low-angle GBs of monolayer tungsten diselenide (WSe2) with misorientation angles of 3-6°. Butterfly features are observed along the GBs, with the periodicity depending on the misorientation angle. Density functional theory calculations show that these butterfly features correspond to gap states that arise in tetragonal dislocation cores and extend to distorted six-membered rings around the dislocation core. Understanding the nature of GB defects and their influence on transport and other device properties highlights the importance of defect engineering in future 2D device fabrication. © 2016 American Chemical Society.

  5. Defect induced d0 ferromagnetism in a ZnO grain boundary

    KAUST Repository

    Devi, Assa Aravindh Sasikala

    2015-12-08

    Several experimental studies have referred to the grain boundary(GB) defect as the origin of ferromagnetism in zinc oxide (ZnO). However, the mechanism of this hypothesis has never been confirmed. Present study investigates the atomic structure and the effect of point defects in a ZnOGB using the generalized gradient approximation+U approximation. The relaxed GB possesses large periodicity and channels with 8 and 10 numbered atoms having 4 and 3 fold coordination. The Znvacancy (VZn) shows a tendency to be attracted to the GB, relative to the bulk-like region. Although no magnetization is obtained from point defect-free GB, VZn induces spin polarization as large as 0.68 μB/atom to the O sites at the GB.Ferromagnetic exchange energy >150 eV is obtained by increasing the concentration of VZn and by the injection of holes into the system. Electronic structure analysis indicates that the spin polarization without external dopants originates from the O 2p orbitals, a common feature of d0semiconductors.

  6. Grain boundary phosphorus segregation under thermal aging in low alloy steels

    International Nuclear Information System (INIS)

    Nakata, Hayato; Fujii, Katsuhiko; Fukuya, Koji; Kasada, Ryuta; Kimura, Akihiko

    2007-01-01

    Intergranular embrittlement due to grain boundary segregation of phosphorus is recognized as one of the potential degradation factors in irradiated reactor low alloy steels at high neutron fluence. In this study, low alloy steels thermally aged at 400-500degC were investigated to evaluate the correlation between phosphorus segregation and intergranular embrittlement. Phosphorus segregation determined using Auger electron spectroscopy increased after thermal aging above 450degC and was in good agreement with the calculated value based on McLean's model. No influence of thermal aging on tensile properties or hardness was observed. The ductile brittle transition temperature determined using a one-third size Charpy impact test increased at a P/Fe peak ratio of 0.14. These results indicated that there is a threshold level of phosphorus segregation for non-hardening embrittlement. DBTT increased with the proportion of intergranular fracture, so this result shows that there is a relationship between DBTT and the properties of intergranular fracture. The fracture stress decreases due to non-hardening embrittlement on the thermally aged material with high proportion of intergranular fracture. (author)

  7. Grain Boundary Induced Bias Instability in Soluble Acene-Based Thin-Film Transistors

    Science.gov (United States)

    Nguyen, Ky V.; Payne, Marcia M.; Anthony, John E.; Lee, Jung Hun; Song, Eunjoo; Kang, Boseok; Cho, Kilwon; Lee, Wi Hyoung

    2016-09-01

    Since the grain boundaries (GBs) within the semiconductor layer of organic field-effect transistors (OFETs) have a strong influence on device performance, a substantial number of studies have been devoted to controlling the crystallization characteristics of organic semiconductors. We studied the intrinsic effects of GBs within 5,11-bis(triethylsilylethynyl) anthradithiophene (TES-ADT) thin films on the electrical properties of OFETs. The GB density was easily changed by controlling nulceation event in TES-ADT thin films. When the mixing time was increased, the number of aggregates in as-spun TES-ADT thin films were increased and subsequent exposure of the films to 1,2-dichloroethane vapor led to a significant increase in the number of nuleation sites, thereby increasing the GB density of TES-ADT spherulites. The density of GBs strongly influences the angular spread and crystallographic orientation of TES-ADT spherulites. Accordingly, the FETs with higher GB densities showed much poorer electrical characteristics than devices with lower GB density. Especially, GBs provide charge trapping sites which are responsible for bias-stress driven electrical instability. Dielectric surface treatment with a polystyrene brush layer clarified the GB-induced charge trapping by reducing charge trapping at the semiconductor-dielectric interface. Our study provides an understanding on GB induced bias instability for the development of high performance OFETs.

  8. Stable High-Performance Perovskite Solar Cells via Grain Boundary Passivation

    KAUST Repository

    Niu, Tianqi

    2018-03-12

    The trap states at grain boundaries (GBs) within polycrystalline perovskite films deteriorate their optoelectronic properties, making GB engineering particularly important for stable high-performance optoelectronic devices. It is demonstrated that trap states within bulk films can be effectively passivated by semiconducting molecules with Lewis acid or base functional groups. The perovskite crystallization kinetics are studied using in situ synchrotron-based grazing-incidence X-ray scattering to explore the film formation mechanism. A model of the passivation mechanism is proposed to understand how the molecules simultaneously passivate the Pb-I antisite defects and vacancies created by under-coordinated Pb atoms. In addition, it also explains how the energy offset between the semiconducting molecules and the perovskite influences trap states and intergrain carrier transport. The superior optoelectronic properties are attained by optimizing the molecular passivation treatments. These benefits are translated into significant enhancements of the power conversion efficiencies to 19.3%, as well as improved environmental and thermal stability of solar cells. The passivated devices without encapsulation degrade only by ≈13% after 40 d of exposure in 50% relative humidity at room temperature, and only ≈10% after 24 h at 80 °C in controlled environment.

  9. Use of small angle neutron scattering to study grain boundary cavitation

    International Nuclear Information System (INIS)

    Yang, M.; Weertman, J.R.; Roth, M.

    1984-01-01

    The technique of small angle neutron scattering can be used to obtain information on cavitation (e.g. void volume fractions, void size distributions, nucleation rates) which can scarcely be duplicated by other void measurement methods. Void size distribution curves for creep cavities in copper show that no voids are detectable below a cutoff radius which corresponds to the smallest stable void radius rsub(c) predicted by the equation rsub(c) = 2ν/σ. (Here ν is the surface energy and σ is the normal stress acting across the grain boundary). In contrast, most of the voids in copper fatigued under similar conditions (same temperature, stress amplitude equal to the creep stress) are far below this critical size. The average size of fatigue voids does not change appreciably with continued deformation whereas the average size of creep voids moves toward larger radii. There is no evidence for the existence of an incubation time associated with void nucleation. It is found that the void density is proportional to the creep time and therefore to the creep strain. (author)

  10. Influence of point defects on grain boundary mobility in bcc tungsten.

    Science.gov (United States)

    Borovikov, Valery; Tang, Xian-Zhu; Perez, Danny; Bai, Xian-Ming; Uberuaga, Blas P; Voter, Arthur F

    2013-01-23

    Atomistic computer simulations were performed to study the influence of radiation-induced damage on grain boundary (GB) sliding processes in bcc tungsten (W), the divertor material in the ITER tokamak and the leading candidate for the first wall material in future fusion reactors. In particular, we calculated the average sliding-friction force as a function of the number of point defects introduced into the GB for a number of symmetric tilt GBs. In all cases the average sliding-friction force at fixed shear strain rate depends on the number of point defects introduced into the GB, and in many cases introduction of these defects reduces the average sliding-friction force by roughly an order of magnitude. We have also observed that as the number of interstitials in the GB is varied, the direction of the coupled GB motion sometimes reverses, causing the GB to migrate in the opposite direction under the same applied shear stress. This could be important in the microstructural evolution of polycrystalline W under the harsh radiation environment in a fusion reactor, in which high internal stresses are present and frequent collision cascades generate interstitials and vacancies.

  11. Atomic-scale analysis of liquid-gallium embrittlement of aluminum grain boundaries

    International Nuclear Information System (INIS)

    Rajagopalan, M.; Bhatia, M.A.; Tschopp, M.A.; Srolovitz, D.J.; Solanki, K.N.

    2014-01-01

    Material strengthening and embrittlement are controlled by intrinsic interactions between defects, such as grain boundaries (GBs), and impurity atoms that alter the observed deformation and failure mechanisms in metals. In this work, we explore the role of atomistic-scale energetics on liquid-metal embrittlement of aluminum (Al) due to gallium (Ga). Ab initio and molecular mechanics were employed to probe the formation/binding energies of vacancies and segregation energies of Ga for 〈1 0 0〉, 〈1 1 0〉 and 〈1 1 1〉 symmetric tilt grain boundaries (STGBs) in Al. We found that the GB local arrangements and resulting structural units have a significant influence on the magnitude of the vacancy binding energies. For example, the mean vacancy binding energies for 〈1 0 0〉, 〈1 1 0〉 and 〈1 1 1〉 STGBs in the 1st layer was found to be −0.63, −0.26 and −0.60 eV, respectively. However, some GBs exhibited vacancy binding energies closer to bulk values, indicating interfaces with zero sink strength, i.e. these GBs may not provide effective pathways for vacancy diffusion. The results from the present work showed that the GB structure and the associated free volume also play significant roles in Ga segregation and the subsequent embrittlement of Al. The Ga mean segregation energies for 〈1 0 0〉, 〈1 1 0〉 and 〈1 1 1〉 STGBs in the 1st layer were found to be −0.21, −0.09 and −0.21 eV, respectively, suggesting a stronger correlation between the GB structural unit, its free volume and the segregation behavior. Furthermore, as the GB free volume increased, the difference in segregation energies between the 1st layer and the 0th layer increased. Thus, the GB character and free volume provide an important key to understanding the degree of anisotropy in various systems. The overall characteristic Ga absorption length scale was found to be about ∼10, 8 and 12 layers for 〈1 0 0〉, 〈1 1 0〉 and 〈1 1 1〉 STGBs, respectively. In addition, a

  12. Grain boundary segregation of cation dopants in {alpha}-Al{sub 2}O{sub 3} scales

    Energy Technology Data Exchange (ETDEWEB)

    Pint, B.A.; Alexander, K.B.

    1996-12-31

    A Fe-20at.%Cr-10%Al matrix was dispersed with a wide range of different oxides in order to study the effect of oxygen-active dopants on the high-temperature growth and adhesion of {alpha}-Al{sub 2}O{sub 3} scales. Effect of these various cation dopants on the alumina scale microstructure was correlated with dopant ion segregation to the {alpha}-Al{sub 2}O{sub 3} grain boundaries using analytical electron microscopy. Elements such as Mn and V showed little effect on the oxide scale and were not observed to segregate. Elements such as Y and Gd resulted in finer, more columnar {alpha}-Al{sub 2}O{sub 3} grains and were segregated to scale grain boundaries. However, Ti, Ta, Ca, and Nb also were found to segregate but had a lesser effect on scale morphology. This indicates that cation segregation to scale grain boundaries is not a sufficient condition to achieve beneficial oxidation effects. The driving force for segregation in growing alumina scales is discussed.

  13. Achieving ultrafine grained and homogeneous AA1050/ZnO nanocomposite with well-developed high angle grain boundaries through accumulative press bonding

    Energy Technology Data Exchange (ETDEWEB)

    Amirkhanlou, Sajjad, E-mail: s.amirkhanlou@aut.ac.ir [Young Researchers and Elite Club, Najafabad Branch, Islamic Azad University, Najafabad (Iran, Islamic Republic of); Ketabchi, Mostafa; Parvin, Nader; Askarian, Masoomeh [Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Carreño, Fernando [Department of Physical Metallurgy, CENIM-CSIC, Av. Gregorio del Amo 8, 28040 Madrid (Spain)

    2015-03-11

    Aluminum matrix nanocomposites with 2 vol% ZnO nanoparticles were produced using accumulative press bonding (APB) as a very effective and novel severe plastic deformation process. Microstructural evaluation and mechanical properties of specimens were characterized by field-emission scanning electron microscopy (FE-SEM), scanning transmission electron microscopy (STEM), electron backscatter diffraction (EBSD) and tensile test. Microstructure of AA1050/ZnO nanocomposite showed a uniform distribution of ZnO nanoparticles throughout the aluminum matrix. STEM and EBSD observations revealed that ultrafine-grained Al/ZnO nanocomposite with the average grain size of <500 nm and well-developed high angle grain boundaries (80% high angle boundaries and 37° average misorientation angle) was successfully obtained by performing 14 cycles of the APB process. When the number of APB cycles increased the tensile strength of Al/ZnO nanocomposite improved and reached 228 MPa after 14 cycles, which was 2.6 and 1.3 times greater than the obtained values for annealed (raw material, 88 MPa) and monolithic aluminum (180 MPa), respectively.

  14. Mesoscopic current transport in two-dimensional materials with grain boundaries: Four-point probe resistance and Hall effect

    DEFF Research Database (Denmark)

    Lotz, Mikkel Rønne; Boll, Mads; Østerberg, Frederik Westergaard

    2016-01-01

    We have studied the behavior of micro four-point probe (M4PP) measurements on two-dimensional (2D) sheets composed of grains of varying size and grain boundary resistivity by Monte Carlo based finite element (FE) modelling. The 2D sheet of the FE model was constructed using Voronoi tessellation...... to emulate a polycrystalline sheet, and a square sample was cut from the tessellated surface. Four-point resistances and Hall effect signals were calculated for a probe placed in the center of the square sample as a function of grain density n and grain boundary resistivity ρGB. We find that the dual...... configuration sheet resistance as well as the resistance measured between opposing edges of the square sample have a simple unique dependency on the dimension-less parameter √nρGBG0, where G0 is the sheet conductance of a grain. The value of the ratio RA/RB between resistances measured in A- and B...

  15. Characterization of boundary roughness of two cube grains in partly recrystallized copper

    DEFF Research Database (Denmark)

    Sun, Jun; Zhang, Yubin; Dahl, Anders Bjorholm

    2015-01-01

    Protrusions and retrusions typically form on recrystallizing boundaries and thus the boundaries often appear rough. Characterization of the boundary roughness is necessary in order to evaluate the effects of protrusions and retrusions on boundary migration. In the current work, a variable termed ...

  16. Grain boundary engineering in sintered Nd-Fe-B permanent magnets for efficient utilization of heavy rare earth elements

    Energy Technology Data Exchange (ETDEWEB)

    Loewe, Konrad

    2016-10-18

    The first part of the thesis investigates the diffusion of rare-earth (RE) elements in commercial sintered Nd-Fe-B based permanent magnets. A strong temperature dependence of the diffusion distance and resulting change in magnetic properties were found. A maximum increase in coercivity of ∼+350 kA/m using a Dy diffusion source occurred at the optimum annealing temperature of 900 C. After annealing for 6 h at this temperature, a Dy diffusion distance of about 4 mm has been observed with a scanning Hall probe. Consequently, the maximum thickness of grain boundary diffusion processed magnets with homogeneous properties is also only a few mm. The microstructural changes in the magnets after diffusion were investigated by electron microscopy coupled with electron probe microanalysis. It was found that the diffusion of Dy into sintered Nd-Fe-B permanent magnets occurs along the grain boundary phases, which is in accordance with previous studies. A partial melting of the Nd-Fe-B grains during the annealing process lead to the formation of so - called (Nd,Dy)-Fe-B shells at the outer part of the grains. These shells are μm thick at the immediate surface of the magnet and become thinner with increasing diffusion distance towards the center of the bulk. With scanning transmission electron microscopy coupled with electron probe analysis a Dy content of about 1 at.% was found in a shell located about 1.5 mm away from the surface of the magnet. The evaluation of diffusion speeds of Dy and other RE (Tb, Ce, Gd) in Nd-Fe-B magnets showed that Tb diffuses significantly faster than Dy, and Ce slightly slower than Dy, which is attributed to differences in the respective phase diagrams. The addition of Gd to the grain boundaries has an adverse effect on coercivity. Exemplary of the heavy rare earth element Tb, the nano - scale elemental distribution around the grain boundaries after the diffusion process was visualized with high resolution scanning transmission electron microscopy

  17. Grain boundaries at the surface of consolidated MgO nanocrystals and acid-base functionality.

    Science.gov (United States)

    Vingurt, Dima; Fuks, David; Landau, Miron V; Vidruk, Roxana; Herskowitz, Moti

    2013-09-21

    The increase of the surface basicity-acidity of MgO material by factors of 1.8-3.0 due to consolidation of its nanocrystals was demonstrated by the indicator titration. It was shown that the parallel increase of surface acidity and basicity is attributed to the formation of grain boundaries (GB) after MgO aerogel densification. A simple model predicting the increase of surface acidity-basicity of MgO that correlates with the results of direct measurements was proposed. The model is based on the study of the fine atomic structure at GB surface areas in consolidated MgO nanocrystals in the framework of Density Functional Theory. It is found that the displacements of coordinatively unsaturated surface ions near the GB are significant at the distances ~3-4 atomic layers from the geometrical contact plane between nanocrystals. The detailed analysis of atomic positions inside GB demonstrated the coordination deficiency of surface atoms at the GB areas leading to the formation of stretched bonds and to creation of low coordinated surface ions due to splitting of coordination numbers of surface atoms belonging to GB areas. Density of states for electrons shows the existence of additional states in the band gap close to the bottom of the conduction band. The adsorption energy of CO2 molecules atop oxygen atoms exposed at surface GB areas is of the same order of magnitude as that reported for oxygen atoms at crystallographic edges and corners of MgO crystals. It provides additional options for bonding of molecules at the surface of nanocrystalline MgO increasing the adsorption capacity and catalytic activity.

  18. Segregation of sp-impurities at grain boundaries and surfaces: comparison of fcc cobalt and nickel

    Science.gov (United States)

    Všianská, M.; Vémolová, H.; Šob, M.

    2017-12-01

    We perform systematic ab initio investigations of the segregation of 12 non-magnetic sp-impurities (Al, Si, P, S, Ga, Ge, As, Se, In, Sn, Sb and Te) at the Σ5(210) grain boundary (GB) and (210) free surface (FS) in fcc ferromagnetic cobalt and analyse their effect on structural, magnetic and mechanical properties; the results are compared with those obtained previously for nickel. It turns out that there is a slight enhancement of magnetization at the clean GB and FS with respect to bulk cobalt (4.7% and 17%, respectively). However, segregated sp-impurities sharply reduce this magnetization. As shown previously, in nickel most of the above impurities nearly destroy or substantially reduce the magnetic moments at the FS and, when segregated interstitially (i.e. Si, P, S, Ge, As, and Se), also at the GB, so that they provide atomically thin, magnetically dead layers, which may be very desirable in spintronics. The reduction of magnetic moments at the Σ5(210) GB in fcc ferromagnetic cobalt is, in absolute values, very similar to that in nickel. However, as the magnetic moment in bulk cobalt is higher, we do not observe magnetically dead layers here. Further, we find the preferred segregation sites at the Σ5(210) GB for the sp-impurities studied, and their segregation enthalpies and strengthening/embrittling energies with their decomposition into their chemical and mechanical components. It turns out that interstitially segregated Si is a GB cohesion enhancer, and interstitially segregated P, S, Ge, As, and Se and substitutionally segregated Al, Ga, In, Sn, Sb and Te are GB embrittlers in fcc cobalt. As there is essentially no experimental information on GB segregation in cobalt, most of the present results are theoretical predictions which may motivate future experimental work.

  19. The Hide-and-Seek of Grain Boundaries from Moiré Pattern Fringe of Two-Dimensional Graphene

    Science.gov (United States)

    Kim, Jung Hwa; Kim, Kwanpyo; Lee, Zonghoon

    2015-01-01

    Grain boundaries (GBs) commonly exist in crystalline materials and affect various properties of materials. The facile identification of GBs is one of the significant requirements for systematical study of polycrystalline materials including recently emerging two-dimensional materials. Previous observations of GBs have been performed by various tools including high resolution transmission electron microscopy. However, a method to easily identify GBs, especially in the case of low-angle GBs, has not yet been well established. In this paper, we choose graphene bilayers with a GB as a model system and investigate the effects of interlayer rotations to the identification of GBs. We provide a critical condition between adjacent moiré fringe spacings, which determines the possibility of GB recognition. In addition, for monolayer graphene with a grain boundary, we demonstrate that low-angle GBs can be distinguished easily by inducing moiré patterns deliberately with an artificial reference overlay. PMID:26216628

  20. Coercivity Enhancement of Nd-Fe-B HDDR Powder by Grain Boundary Diffusion Process with Rare-Earth Hydride

    Science.gov (United States)

    Cha, Hee-Ryoung; Yoo, Jae-Gyeong; Baek, Youn-Kyoung; Kim, Dong-Hwan; Kwon, Hae-Woong; Kim, Yang-Do; Lee, Dongyun; Lee, Jung-Goo

    2018-02-01

    The grain boundary diffusion (GBD) process with rare-earth hydride was performed to increase the coercivity of hydrogenation-disproportionation-desorption-recombination (HDDR) powder. Before the GBD process, we investigated the effect of post-annealing of the initial HDDR powder on its magnetic properties. Low-temperature annealing reduced the coercivity of the HDDR powder. However, the coercivity decline decreased with increasing annealing temperature, becoming similar to that of the initial powder at 900°C. After the GBD process at 850°C for 1 h, the coercivity increased by about 4 kOe with 4 wt.% NdH x -Cu, forming a thick and continuous grain boundary phase. In addition, the coercivity and remanence of the HDDR powder produced by the GBD process with NdH x -Cu were higher when using NdH x in spite of the same amount of diffusion as at 2 wt.%.

  1. Identical mechanism of isochronal and isothermal embrittlement in Ni(Bi) alloy: Thermo-induced non-equilibrium grain-boundary segregation of Bi

    International Nuclear Information System (INIS)

    Zheng, Lei; Chellali, Reda; Schlesiger, Ralf; Meng, Ye; Baither, Dietmar; Schmitz, Guido

    2015-01-01

    Highlights: • Both isochronal and isothermal plasticity of Ni(Bi) alloy show minima. • Existing interpretations for isochronal and isothermal embrittlement are inadequate. • Both embrittlement is caused by thermo-induced non-equilibrium grain-boundary segregation of Bi. - Abstract: Isochronal and isothermal plasticity after thermal pre-treatments are obtained by tensile tests to characterize the embrittling behaviors of Ni(Bi) alloy. Both isochronal and isothermal plasticity show evident minima. Fractography observed by scanning electron microscopy displays intergranular fracture for samples of low plasticity. The microstructure is found to be free of precipitates within grains and at grain boundaries by focused ion beam and transmission electron microscopy. Atom probe analysis indicates a strong tendency of Bi segregation to grain boundaries. By these results, the existing interpretations are discussed to be inadequate and both embrittlement are confirmed to be identical in mechanism, i.e. thermo-induced non-equilibrium grain-boundary segregation of Bi

  2. Effects of processing optimisation on microstructure, texture, grain boundary and mechanical properties of Fe–17Cr ferritic stainless steel thick plates

    Energy Technology Data Exchange (ETDEWEB)

    Han, Jian, E-mail: jh595@uowmail.edu.au [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522 (Australia); Li, Huijun; Zhu, Zhixiong [School of Mechanical, Materials and Mechatronic Engineering, University of Wollongong, Wollongong, NSW 2522 (Australia); Jiang, Laizhu; Xu, Haigang; Ma, Li [Baoshan Iron and Steel Co., Ltd., Shanghai 200431 (China)

    2014-10-20

    The relationships between microstructure, texture, grain boundary and tensile strength, Charpy impact toughness of (Nb+Ti+V) stabilised Fe–17Cr ferritic stainless steel thick plates were investigated by means of optical microscopy, X-ray diffraction, scanning electron microscopy, electron backscatter diffraction, tensile and Charpy impact testing. The results show that for Fe–17Cr ferritic stainless steel thick plate, the addition of warm rolling procedure leads to refinement of grain size, modification of texture, and then optimisation of grain boundary, including grain boundary character distribution and grain boundary connectivity. Meanwhile, the mechanical testing results indicate that optimal transformation that warm rolling procedure brings to Fe–17Cr ferritic steel thick plate is beneficial to its mechanical properties.

  3. Direct imaging of enhanced current collection on grain boundaries of Cu(In,Ga)Se{sub 2} solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Kim, JunHo, E-mail: jhk@incheon.ac.kr [Department of Physics, Incheon National University, Incheon 406-772 (Korea, Republic of); National Center for Photovoltaics, National Renewable Energy Laboratory (NREL), Golden, Colorado 80401 (United States); Kim, SeongYeon [Department of Physics, Incheon National University, Incheon 406-772 (Korea, Republic of); Jiang, Chun-Sheng; Ramanathan, Kannan; Al-Jassim, Mowafak M. [National Center for Photovoltaics, National Renewable Energy Laboratory (NREL), Golden, Colorado 80401 (United States)

    2014-02-10

    We report on direct imaging of current collection by performing conductive atomic force microscopy (C-AFM) measurement on a complete Cu(In,Ga)Se{sub 2} solar cell. The localized current was imaged by milling away the top conductive layer of the device by repeated C-AFM scans. The result exhibits enhanced photocurrent collection on grain boundaries (GBs) of CIGS films, consistent with the argument for electric-field-assisted carrier collection on the GBs.

  4. Effect of grain boundary segregation on mechanical properties of p-doped Fe-Si base alloys

    Czech Academy of Sciences Publication Activity Database

    Janovec, J.; Jenko, M.; Pokluda, J.; Vlach, B.; Lejček, Pavel; Svoboda, Milan; Šandera, P.

    2005-01-01

    Roč. 482, - (2005), s. 191-194 ISSN 0255-5476 R&D Projects: GA ČR(CZ) GA106/02/0253 Institutional research plan: CEZ:AV0Z1010914 Keywords : Fe-Si alloys * phosphorus grain boundary segregation * mechanical properties * Auger electron spectroscopy * transmission electron microscopy * mechanical testing Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.399, year: 2005

  5. Effect of grain boundary segragation on mechanical properties of P-doped Fe-Si base alloys

    Czech Academy of Sciences Publication Activity Database

    Janovec, J.; Jenko, M.; Pokluda, J.; Vlach, B.; Lejček, Pavel; Svoboda, Milan; Šandera, P.

    2005-01-01

    Roč. 482, - (2005), s. 191-194 ISSN 0255-5476 R&D Projects: GA ČR(CZ) GA106/02/0253 Institutional research plan: CEZ:AV0Z20410507; CEZ:AV0Z40320502; CEZ:AV0Z10100520 Keywords : Fe-Si alloys * phosphorus grain boundary segregation * mechanical properties Subject RIV: JG - Metallurgy Impact factor: 0.399, year: 2005

  6. Grain boundary segregation of elements of groups 14 and 15 and its consequences for intergranular cohesion of ferritic iron

    Czech Academy of Sciences Publication Activity Database

    Lejček, Pavel; Šandera, P.; Horníková, J.; Řehák, Petr; Pokluda, J.

    2017-01-01

    Roč. 52, č. 10 (2017), s. 5822-5834 ISSN 0022-2461 R&D Projects: GA ČR GAP108/12/0144; GA MŠk(CZ) LQ1601 Institutional support: RVO:68378271 ; RVO:68081723 Keywords : grain boundary segregation * segregation enthalpy * intergranular fracture * strengthening/embrittling energy Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 2.599, year: 2016

  7. First-Order Interfacial Transformations with a Critical Point: Breaking the Symmetry at a Symmetric Tilt Grain Boundary

    Science.gov (United States)

    Yang, Shengfeng; Zhou, Naixie; Zheng, Hui; Ong, Shyue Ping; Luo, Jian

    2018-02-01

    First-order interfacial phaselike transformations that break the mirror symmetry of the symmetric ∑5 (210 ) tilt grain boundary (GB) are discovered by combining a modified genetic algorithm with hybrid Monte Carlo and molecular dynamics simulations. Density functional theory calculations confirm this prediction. This first-order coupled structural and adsorption transformation, which produces two variants of asymmetric bilayers, vanishes at an interfacial critical point. A GB complexion (phase) diagram is constructed via semigrand canonical ensemble atomistic simulations for the first time.

  8. Ab initio tensile tests of grain boundaries in the fcc crystals of Ni and Co with segregated sp-impurities

    Czech Academy of Sciences Publication Activity Database

    Černý, Miroslav; Šešták, Petr; Řehák, Petr; Všianská, Monika; Šob, Mojmír

    2016-01-01

    Roč. 669, JUL (2016), s. 218-225 ISSN 0921-5093 R&D Projects: GA ČR(CZ) GA16-24711S; GA ČR(CZ) GAP108/12/0311; GA MŠk(CZ) LQ1601 Institutional support: RVO:68081723 Keywords : Theoretical strength * Computational tensile test * Grain boundary embrittlement * Ab initio calculations Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.094, year: 2016

  9. Molecular dynamics study on the diffusion behavior of Li in the grain boundaries of α-Fe

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Xingang, E-mail: xgyu@ucas.ac.cn [School of Engineering Science, University of Chinese Academy of Sciences, Beijing 100049 (China); Liu, Chengrui [Beijing Institute of Control Engineering, Beijing 100190 (China); Han, Tiansi [Academy of Mathematics and Systems Science, Chinese Academy of Sciences, Beijing 100190 (China); Gan, Xianglai [College of Materials Science and Engineering, Hunan University, Changsha 410082 (China)

    2016-11-01

    Highlights: • Confirmed the strong binding effect between the grain boundaries and lithium interstitials. • Determined the critical temperatures for a lithium atom to diffuse in the grain boundaries. • Revealed that the diffusion mechanism of a lithium atom depends on the grain boundary structure. - Abstract: Liquid lithium has been considered as a candidate material for several components of future fusion devices. Since the containment materials are usually ferrous alloys, molecular dynamics simulations were performed to study the diffusion behavior of lithium atoms along <110> tilt grain boundaries (GB) including Σ9{114}, Σ11{113}, Σ3{112} and Σ11{332} in α-Fe. The binding energies of a Li interstitial to the GBs were calculated. The results suggest that all the GBs have strong binding effect on the Li atom. The critical temperatures for the Li atom to diffuse were determined. The diffusion process of a Li interstitial in the GBs was systematically analyzed. It turns out that the diffusion mechanism depends on the GB structures. For Σ11{113} and GB Σ9{114}, the Li atom was trapped by the Frenkel defect around the GBs at 300 K and 400 K respectively and therefore the diffusion was slowed down rapidly. For Σ3{112}, no defects were formed around GB and the Li atom diffused into Fe bulk at 700 K and above. For Σ3{112}, the diffusion process is driven by the movement of the GB. Finally, the diffusion coefficient, as well as the activation energy, was evaluated.

  10. Fabrication of 45 degrees template grain boundary junctions using a CaO lift-off technique

    NARCIS (Netherlands)

    IJsselsteijn, R.P.J.; Terpstra, D.; Flokstra, Jakob; Rogalla, Horst

    1994-01-01

    45 degrees grain boundary junctions have been made using (100) MgO substrates, a CeO2 template layer and an YBa2Cu3O7 top layer. To minimize the damage to the MgO surface, which will occur if the CeO2 is structured using ion milling, the CeO2 layer has been structured using the CaO lift-off

  11. A Combined TEM/STEM and Micromagnetic Study of the Anisotropic Nature of Grain Boundaries and Coercivity in Nd-Fe-B Magnets

    Directory of Open Access Journals (Sweden)

    Gregor A. Zickler

    2017-01-01

    Full Text Available The nanoanalytical high resolution TEM/STEM investigation of the intergranular grain boundary phase of anisotropic sintered and rapidly quenched heavy rare earth-free Nd-Fe-B magnet materials revealed a difference in composition for grain boundaries parallel (large Fe-content and perpendicular (low Fe content to the alignment direction. This behaviour vanishes in magnets with a high degree of misorientation. The numerical finite element micromagnetic simulations are based on the anisotropic compositional behaviour of GBs and show a decrease of the coercive field with an increasing thickness of the grain boundary layer. The magnetization reversal and expansion of reversed magnetic domains primarily start as Bloch domain wall at grain boundaries parallel to the c-axis and secondly as Néel domain wall perpendicular to the c-axis into the adjacent hard magnetic grains. The increasing misalignment of grains leads to the loss of the anisotropic compositional behaviour and therefore to an averaged value of the grain boundary composition. In this case the simulations show an increase of the coercive field compared to the anisotropic magnet. The calculated coercive field values of the investigated magnet samples are in the order of μ0HcJ=1.8 T–2.1 T for a mean grain boundary thickness of 4 nm, which agrees perfectly with the experimental data.

  12. 3D Microstructural Characterization of Uranium Oxide as a Surrogate Nuclear Fuel: Effect of Oxygen Stoichiometry on Grain Boundary Distributions

    Energy Technology Data Exchange (ETDEWEB)

    Rudman, K. [Arizona State Univ., Tempe, AZ (United States); Dickerson, P. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Byler, Darrin David [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Peralta, P. [Arizona State Univ., Tempe, AZ (United States); Lim, H. [Arizona State Univ., Tempe, AZ (United States); McDonald, R. [Arizona State Univ., Tempe, AZ (United States); Dickerson, R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Mcclellan, Kenneth James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-09-06

    The initial microstructure of an oxide fuel can play a key role in its performance. At low burn-ups, the diffusion of fission products can depend strongly on grain size and grain boundary (GB) characteristics, which in turn depend on processing conditions and oxygen stoichiometry. Serial sectioning techniques using Focused Ion Beam were developed to obtain Electron Backscatter Diffraction (EBSD) data for depleted UO2 pellets that were processed to obtain 3 different oxygen stoichiometries. The EBSD data were used to create 3D microstructure reconstructions and to gather statistical information on the grain and GB crystallography, with emphasis on identifying the character (twist, tilt, mixed) for GBs that meet the Coincident Site Lattice (CSL) criterion as well as GBs with the most common misorientation angles. Data on dihedral angles at triple points were also collected. The results were compared across different samples to understand effects of oxygen content on microstructure evolution.

  13. Slip, twinning, and fracture at a grain boundary in the L1/sub 2/ ordered structure: A. sigma. = 9 tilt boundary

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, M.H.; King, A.H.

    1988-09-01

    The role of interaction between slip dislocations and a ..sigma.. = 9 tilt boundary in localized microplastic deformation, cleavage, or intergranular fracture in the L1/sub 2/ ordered structure has been analyzed by using the anisotropic elasticity theory of dislocations and fracture. Screw superpartials cross slip easily at the boundary onto the (11-bar1) and the (001) planes at low and high temperatures, respectively. Transmission of primary slip dislocations onto the conjugate slip system occurs with a certain degree of difficulty, which is eased by localized disordering. When the transmission is impeded, cleavage fracture on the (1-bar11) plane is predicted to occur, not intergranular fracture, unless a symmetric double pileup occurs simultaneously. Absorption (or emission) of superpartials occurs only when the boundary region is disordered. Slip initiation from pre-existing sources near the boundary can occur under the local stress concentration. Implications of the present result on the inherent brittleness of grain boundaries in Ni/sub 3/ Al and its improvement by boron segregation are discussed.

  14. Effect of non-metallic precipitates and grain size on core loss of non-oriented electrical silicon steels

    Science.gov (United States)

    Wang, Jiayi; Ren, Qiang; Luo, Yan; Zhang, Lifeng

    2018-04-01

    In the current study, the number density and size of non-metallic precipitates and the size of grains on the core loss of the 50W800 non-oriented electrical silicon steel sheets were investigated. The number density and size of precipitates and grains were statistically analyzed using an automatic scanning electron microscope (ASPEX) and an optical microscope. Hypothesis models were established to reveal the physical feature for the function of grain size and precipitates on the core loss of the steel. Most precipitates in the steel were AlN particles smaller than 1 μm so that were detrimental to the core loss of the steel. These finer AlN particles distributed on the surface of the steel sheet. The relationship between the number density of precipitates (x in number/mm2 steel area) and the core loss (P1.5/50 in W/kg) was regressed as P1.5/50 = 4.150 + 0.002 x. The average grain size was approximately 25-35 μm. The relationship between the core loss and grain size (d in μm) was P1.5/50 = 3.851 + 20.001 d-1 + 60.000 d-2.

  15. Grain boundary imaging, gallium diffusion and the fracture behavior of Al-Zn Alloy - An in situ study

    CERN Document Server

    Tsai, W L; Chen, C H; Chang, L W; Je, J H; Lin, H M; Margaritondo, G

    2003-01-01

    Phase contrast radiology using unmonochromatic synchrotron X-ray successfully imaged the grain boundaries of Al and AlZn alloy without contrast agent. Combining the high penetration of X-ray and the possibility of 3D reconstruction by tomorgraphy or stereography method, this approach can be very used for nondestructive characterization of polycrystalline materials. By examine the images with 3D perspective, we were able locate the observed void-like defects which lies exclusively on the grain boundary and identify their origin from last stage of the rolling process. We studied the Ga Liquid metal diffusion in the AlZn alloy, under different temperature and stress conditions. High resolution images, approx 2 mu m, of Ga liquid metal diffusion in AlZn were obtained in real time and diffusion paths alone grain boundaries and surfaces were clearly identified. Embrittled AlZn responses to the tensile stress and fractures in a drastic different manner than the pure AlZn. These results, although very much expected f...

  16. Boundary Fractal Analysis of Two Cube-oriented Grains in Partly Recrystallized Copper

    DEFF Research Database (Denmark)

    Sun, Jun; Zhang, Yubin; Dahl, Anders Bjorholm

    2015-01-01

    The protrusions and retrusions observed on the recrystallizing boundaries affect the migration kinetics during recrystallization. Characterization of the boundary roughness is necessary in order to evaluate their effects. This roughness has a structure that can be characterized by fractal analysis...

  17. A phase-field simulation study of irregular grain boundary migration during recrystallization

    DEFF Research Database (Denmark)

    Moelans, N.; Zhang, Yubin; Godfrey, A.

    2015-01-01

    We present simulation results based on a phase-field model that describes the migration of recrystallization boundaries into spatially varying deformation energy fields. Energy fields with 2-dimensional variations representing 2 sets of dislocation boundaries lying at equal, but opposite, angles...... in recrystallization experiments. They give new insights in the way deformation microstructures can affect the migration behavior of recrystallization boundaries and can lead to a stop-and-go type of migration of the recrystallization boundary even in pure materials....

  18. Direct observation of nanometer-scale amorphous layers and oxide crystallites at grain boundaries in polycrystalline Sr1−xKxFe2As2 superconductors

    KAUST Repository

    Wang, Lei

    2011-06-01

    We report here an atomic resolution study of the structure and composition of the grain boundaries in polycrystallineSr0.6K0.4Fe2As2superconductor. A large fraction of grain boundaries contain amorphous layers larger than the coherence length, while some others contain nanometer-scale crystallites sandwiched in between amorphous layers. We also find that there is significant oxygen enrichment at the grain boundaries. Such results explain the relatively low transport critical current density (Jc) of polycrystalline samples with respect to that of bicrystal films.

  19. Effect of texture and grain size on the magnetic flux density and core loss of cold-rolled high silicon steel sheets

    Science.gov (United States)

    Qin, Jing; Yang, Ping; Mao, Weimin; Ye, Feng

    2015-11-01

    The effects of texture and grain size on the magnetic flux density and core loss (50-20 kHz) of 0.23 mm-thick cold-rolled high silicon steel sheets are investigated by means of electron back-scattered diffraction (EBSD), loss separation, and anisotropy parameter (ε) calculation. A model of the hysteresis loss coefficient kh considering average grain size and ε is established. The magnetic flux density at 800 A/m (B8) is closely related to the volume fraction of η-fiber-oriented grains, while the magnetic flux density at 5000 A/m (B50) is closely related to the volume fractions of γ- and λ-fiber-oriented grains in high silicon steel. The hysteresis loss of high silicon steel can be greatly reduced by increasing the grain size and optimizing the texture of the sheets. Although increases in frequencies decrease the effect of texture on core loss, the effect cannot be ignored. As annealing temperature and time increase, the relative difference in core loss between the rolling direction (RD) and the transverse direction (TD) is maintained at higher frequencies because of increases in grain size, decreases in γ texture, and maintenance of a strong η texture. Texture and grain size jointly affect the high-frequency core loss of high silicon steel.

  20. Effect of texture and grain size on the magnetic flux density and core loss of cold-rolled high silicon steel sheets

    International Nuclear Information System (INIS)

    Qin, Jing; Yang, Ping; Mao, Weimin; Ye, Feng

    2015-01-01

    The effects of texture and grain size on the magnetic flux density and core loss (50–20 kHz) of 0.23 mm-thick cold-rolled high silicon steel sheets are investigated by means of electron back-scattered diffraction (EBSD), loss separation, and anisotropy parameter (ε) calculation. A model of the hysteresis loss coefficient k h considering average grain size and ε is established. The magnetic flux density at 800 A/m (B 8 ) is closely related to the volume fraction of η-fiber-oriented grains, while the magnetic flux density at 5000 A/m (B 50 ) is closely related to the volume fractions of γ- and λ-fiber-oriented grains in high silicon steel. The hysteresis loss of high silicon steel can be greatly reduced by increasing the grain size and optimizing the texture of the sheets. Although increases in frequencies decrease the effect of texture on core loss, the effect cannot be ignored. As annealing temperature and time increase, the relative difference in core loss between the rolling direction (RD) and the transverse direction (TD) is maintained at higher frequencies because of increases in grain size, decreases in γ texture, and maintenance of a strong η texture. Texture and grain size jointly affect the high-frequency core loss of high silicon steel. - Highlights: • A model of hysteresis loss coefficient considering anisotropy parameter is obtained. • Effect of texture on high-frequency core loss of high-silicon steel cannot be ignored. • Texture and grain size jointly affect high-frequency core loss of high-silicon steel

  1. Effect of texture and grain size on the magnetic flux density and core loss of cold-rolled high silicon steel sheets

    Energy Technology Data Exchange (ETDEWEB)

    Qin, Jing [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Yang, Ping, E-mail: yangp@mater.ustb.edu.cn [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Mao, Weimin [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China); Ye, Feng [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China)

    2015-11-01

    The effects of texture and grain size on the magnetic flux density and core loss (50–20 kHz) of 0.23 mm-thick cold-rolled high silicon steel sheets are investigated by means of electron back-scattered diffraction (EBSD), loss separation, and anisotropy parameter (ε) calculation. A model of the hysteresis loss coefficient k{sub h} considering average grain size and ε is established. The magnetic flux density at 800 A/m (B{sub 8}) is closely related to the volume fraction of η-fiber-oriented grains, while the magnetic flux density at 5000 A/m (B{sub 50}) is closely related to the volume fractions of γ- and λ-fiber-oriented grains in high silicon steel. The hysteresis loss of high silicon steel can be greatly reduced by increasing the grain size and optimizing the texture of the sheets. Although increases in frequencies decrease the effect of texture on core loss, the effect cannot be ignored. As annealing temperature and time increase, the relative difference in core loss between the rolling direction (RD) and the transverse direction (TD) is maintained at higher frequencies because of increases in grain size, decreases in γ texture, and maintenance of a strong η texture. Texture and grain size jointly affect the high-frequency core loss of high silicon steel. - Highlights: • A model of hysteresis loss coefficient considering anisotropy parameter is obtained. • Effect of texture on high-frequency core loss of high-silicon steel cannot be ignored. • Texture and grain size jointly affect high-frequency core loss of high-silicon steel.

  2. Mechanical properties of ceria nanorods and nanochains; the effect of dislocations, grain-boundaries and oriented attachment.

    Science.gov (United States)

    Sayle, Thi X T; Inkson, Beverley J; Karakoti, Ajay; Kumar, Amit; Molinari, Marco; Möbus, Günter; Parker, Stephen C; Seal, Sudipta; Sayle, Dean C

    2011-04-01

    We predict that the presence of extended defects can reduce the mechanical strength of a ceria nanorod by 70%. Conversely, the pristine material can deform near its theoretical strength limit. Specifically, atomistic models of ceria nanorods have been generated with full microstructure, including: growth direction, morphology, surface roughening (steps, edges, corners), point defects, dislocations and grain-boundaries. The models were then used to calculate the mechanical strength as a function of microstructure. Our simulations reveal that the compressive yield strengths of ceria nanorods, ca. 10 nm in diameter and without extended defects, are 46 and 36 GPa for rods oriented along [211] and [110] respectively, which represents almost 10% of the bulk elastic modulus and are associated with yield strains of about 0.09. Tensile yield strengths were calculated to be about 50% lower with associated yield strains of about 0.06. For both nanorods, plastic deformation was found to proceed via slip in the {001} plane with direction --a primary slip system for crystals with the fluorite structure. Dislocation evolution for the nanorod oriented along [110] was nucleated via a cerium vacancy present at the surface. A nanorod oriented along [321] and comprising twin-grain boundaries with {111} interfacial planes was calculated to have a yield strength of about 10 GPa (compression and tension) with the grain boundary providing the vehicle for plastic deformation, which slipped in the plane of the grain boundary, with an associated slip direction. We also predict, using a combination of atomistic simulation and DFT, that rutile-structured ceria is feasible when the crystal is placed under tension. The mechanical properties of nanochains, comprising individual ceria nanoparticles with oriented attachment and generated using simulated self-assembly, were found to be similar to those of the nanorod with grain-boundary. Images of the atom positions during tension and compression

  3. Study of a photovoltaic cell to silicon tri grain under illumination in static mode: determination of the parameters of recombination

    International Nuclear Information System (INIS)

    ZERBO Issa

    2000-01-01

    A study of the photovoltaic cell to silicon tri grain under illumination functioning at a static normal rate is presented. The determination of the parameters of recombination relies on the analysis of the photo-answer of the photovoltaic cell. The length of diffusion L, the speeds of recombination of minority carriers and respectively on the surface of the junction and with the back face of the base of the photovoltaic cell are extracted thanks to the measurement from the from short-circuit electricity and the tension from open circuit [fr

  4. Three-dimensional study of grain boundary engineering effects on intergranular stress corrosion cracking of 316 stainless steel in high temperature water

    Science.gov (United States)

    Liu, Tingguang; Xia, Shuang; Bai, Qin; Zhou, Bangxin; Zhang, Lefu; Lu, Yonghao; Shoji, Tetsuo

    2018-01-01

    The intergranular cracks and grain boundary (GB) network of a GB-engineered 316 stainless steel after stress corrosion cracking (SCC) test in high temperature high pressure water of reactor environment were investigated by two-dimensional and three-dimensional (3D) characterization in order to expose the mechanism that GB-engineering mitigates intergranular SCC. The 3D microstructure shown that the essential characteristic of the GB-engineered microstructure is formation of many large twin-boundaries as a result of multiple-twinning, which results in the formation of large grain-clusters. The large grain-clusters played a key role to the improvement of intergranular SCC resistance by GB-engineering. The main intergranular cracks propagated in a zigzag along the outer boundaries of these large grain-clusters because all inner boundaries of the grain-clusters were twin-boundaries (∑3) or twin-related boundaries (∑3n) which had much lower susceptibility to SCC than random boundaries. These large grain-clusters had tree-ring-shaped topology structure and very complex morphology. They got tangled so that difficult to be separated during SCC, resulting in some large crack-bridges retained in the crack surface.

  5. Silicon processing for photovoltaics II

    CERN Document Server

    Khattak, CP

    2012-01-01

    The processing of semiconductor silicon for manufacturing low cost photovoltaic products has been a field of increasing activity over the past decade and a number of papers have been published in the technical literature. This volume presents comprehensive, in-depth reviews on some of the key technologies developed for processing silicon for photovoltaic applications. It is complementary to Volume 5 in this series and together they provide the only collection of reviews in silicon photovoltaics available.The volume contains papers on: the effect of introducing grain boundaries in silicon; the

  6. The effects of surface finish and grain size on the strength of sintered silicon carbide

    Science.gov (United States)

    You, Y. H.; Kim, Y. W.; Lee, J. G.; Kim, C. H.

    1985-01-01

    The effects of surface treatment and microstructure, especially abnormal grain growth, on the strength of sintered SiC were studied. The surfaces of sintered SiC were treated with 400, 800 and 1200 grit diamond wheels. Grain growth was induced by increasing the sintering times at 2050 C. The beta to alpha transformation occurred during the sintering of beta-phase starting materials and was often accompanied by abnormal grain growth. The overall strength distributions were established using Weibull statistics. The strength of the sintered SiC is limited by extrinsic surface flaws in normal-sintered specimens. The finer the surface finish and grain size, the higher the strength. But the strength of abnormal sintering specimens is limited by the abnormally grown large tabular grains. The Weibull modulus increases with decreasing grain size and decreasing grit size for grinding.

  7. A study of methanol and silicon monoxide production through episodic explosions of grain mantles in the Central Molecular Zone

    Science.gov (United States)

    Coutens, A.; Rawlings, J. M. C.; Viti, S.; Williams, D. A.

    2017-05-01

    Methanol (CH3OH) is found to be abundant and widespread towards the Central Molecular Zone, the inner few hundred parsecs of our Galaxy. Its origin is, however, not fully understood. It was proposed that the high cosmic ray ionization rate in this region could lead to a more efficient non-thermal desorption of this species formed on grain surfaces, but it would also mean that this species is destroyed in a relatively short time-scale. In a first step, we run chemical models with a high cosmic ray ionization rate and find that this scenario can only reproduce the lowest abundances of methanol derived in this region (˜10-9-10-8). In a second step, we investigate another scenario based on episodic explosions of grain mantles. We find a good agreement between the predicted abundances of methanol and the observations. We find that the dominant route for the formation of methanol is through hydrogenation of CO on the grains, followed by the desorption due to the grain mantle explosion. The cyclic aspect of this model can explain the widespread presence of methanol without requiring any additional mechanism. We also model silicon monoxide (SiO), another species detected in several molecular clouds of the Galactic Centre. An agreement is found with observations for a high depletion of Si (Si/H ˜ 10-8) with respect to the solar abundance.

  8. Magnetism in grain-boundary phase of a NdFeB sintered magnet studied by spin-polarized scanning electron microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Kohashi, Teruo, E-mail: teruo.kohashi.fc@hitachi.com; Motai, Kumi [Central Research Laboratory, Hitachi, Ltd., Hatoyama, Saitama 350-0395 (Japan); Nishiuchi, Takeshi; Hirosawa, Satoshi [Magnetic Materials Research Laboratory, Hitachi Metals Ltd., Osaka 618-0013 (Japan)

    2014-06-09

    The magnetism in the grain-boundary phase of a NdFeB sintered magnet was measured by spin-polarized scanning electron microscopy (spin SEM). A sample magnet was fractured in the ultra-high-vacuum chamber to avoid oxidation, and its magnetizations in the exposed grain-boundary phase on the fracture surface were evaluated through the spin polarization of secondary electrons. Spin-SEM images were taken as the fracture surface was milled gradually by argon ions, and the magnetization in the grain-boundary phase was quantitatively obtained separately from that of the Nd{sub 2}Fe{sub 14}B phase. The obtained magnetization shows that the grain-boundary phase of this magnet has substantial magnetization, which was confirmed to be ferromagnetic.

  9. Asymptotic expressions for the nearest and furthest dislocations in a pile-up against a grain boundary

    KAUST Repository

    Hall, Cameron L.

    2010-10-14

    In 1965, Armstrong and Head explored the problem of a pile-up of screw dislocations against a grain boundary. They used numerical methods to determine the positions of the dislocations in the pile-up and they were able to fit approximate formulae for the locations of the first and last dislocations. These formulae were used to gain insights into the Hall-Petch relationship. More recently, Voskoboinikov et al. used asymptotic techniques to study the equivalent problem of a pile-up of a large number of screw dislocations against a bimetallic interface. In this paper, we extend the work of Voskoboinikov et al. to construct systematic asymptotic expressions for the formulae proposed by Armstrong and Head. The further extension of these techniques to more general pile-ups is also outlined. As a result of this work, we show that a pile-up against a grain boundary can become equivalent to a pile-up against a locked dislocation in the case where the mismatch across the boundary is small. © 2010 Taylor & Francis.

  10. Quantification of mineral behavior in four dimensions: Grain boundary and substructure dynamics in salt

    DEFF Research Database (Denmark)

    Borthwick, V. E.; Schmidt, Søren; Piazolo, S.

    2012-01-01

    been questioned. Our study shows that, although the nature of recovery processes are the same, the area swept by subgrain boundaries is up to 5 times larger in the volume than observed on the surface. We suggest this discrepancy is due to enhanced drag force on subgrain boundaries by thermal surface...

  11. Crystallographic Fabrics, Grain Boundary Microstructure and Shape Preferred Orientation of Deformed Banded Iron Formations and their Significance for Deformation Interpretation

    Science.gov (United States)

    Ávila, Carlos Fernando; Graça, Leonardo; Lagoeiro, Leonardo; Ferreira, Filippe

    2016-04-01

    The characterization of grain boundaries and shapes along with crystallographic preferred orientations (CPOs) are a key aspect of investigations of rock microstructures for their correlation with deformation mechanisms. Rapid developments have occurred in the studying rock microstructures due to recent improvements in analytical techniques such as Electron Backscatter Diffraction (EBSD). EBSD technique allows quick automated microtextural characteritzation. The deformed banded iron formations (BIFs) occurring in the Quadrilátero Ferrífero (QF) province in Brazil have been studied extensively with EBSD. All studies have focused mainly in CPOs. The general agreement is that dislocation creep was the dominant process of deformation, for the strong c-axis fabric of hematite crystals. This idea is substantiated by viscoplastic self-consistent models for deformation of hematite. However there are limitations to analyzing natural CPOs alone, or those generated by deformation models. The strong c-axis fabric could be taken as equally powerful an evidence for other known deformation mechanisms. Some grain boundary types in BIFs of the QF are irregular and comprise equant grains in granoblastic texture (Figure 1a). CPOs for this kind are strong and consistent with a predominance of dislocation creep. Others are very regular and long parallel to basal planes of hematites forming large elongated crystals (lepidoblastic texture, Figure 1b). Such crystals are called specularite, and their formation has been previously attributed to dislocation creep. This is erroneous because of the high strains which would be required. Their shape must be due to anisotropic grain growth. Other types lie between the above end-textures. Both types of grain shape microstructures have the same core deformation mechanism. Describing their genetic differences is crucial, since specularite owe its shape to anisotropic grain growth. It is not possible yet to confirm that dislocation creep was the

  12. An Atomistic Modeling Study of Alloying Element Impurity Element, and Transmutation Products on the cohesion of A Nickel E5 {001} Twist Grain Boundary

    International Nuclear Information System (INIS)

    Young, G.A. Jr.; Najafabadi, R.; Strohmayer, W.; Baldrey, D.G.; Hamm, B.; Harris, J.; Sticht, J.; Wimmer, E.

    2003-01-01

    Atomistic modeling methods were employed to investigate the effects of impurity elements on the metallurgy, irradiation embrittlement, and environmentally assisted cracking of nickel-base alloys exposed to nuclear environments. Calculations were performed via ab initio atomistic modeling methods to ensure the accuracy and reliability of the results. A Griffith-type fracture criterion was used to quantitatively assess the effect of elements or element pairs on the grain boundary cohesive strength. In order of most embrittling to most strengthening, the elements are ranked as: He, Li, S, H, C, Zr, P, Fe, Mn, Nb, Cr, and B. Helium is strongly embrittling (-2.04 eV/atom lowering of the Griffith energy), phosphorus has little effect on the grain boundary (0.1 eV/atom), and boron offers appreciable strengthening (1.03 eV/atom increase in the Griffith energy). Calculations for pairs of elements (H-Li, H-B, H-C, H-P, and H-S) show little interaction on the grain boundary cohesive energy, so that for the conditions studied, linear superposition of elemental effects is a good approximation. These calculations help explain metallurgical effects (e.g. why boron can strengthen grain boundaries), irradiation embrittlement (e.g. how boron transmutation results in grain boundary embrittlement), as well as how grain boundary impurity elements can affect environmentally assisted cracking (i.e. low temperature crack propagation and stress corrosion cracking) of nickel-base alloys

  13. Josephson oscillations and noise temperatures in YBa2Cu3O7-x grain-boundary junctions

    DEFF Research Database (Denmark)

    Yu, Ya. Divin; Mygind, Jesper; Pedersen, Niels Falsig

    1992-01-01

    The ac Josephson effect was studied in YBa2Cu3O7−x grain-boundary junctions (GBJ) in the temperature range from 4 to 90 K. The temperature dependence of the linewidth of millimeter-wave Josephson oscillations was measured and it is shown that the derived effective noise temperatures may be as low...... as the physical temperature in the temperature range investigated. In the millimeter-wave range, linewidths as low as 380 MHz were found at liquid-nitrogen temperatures. Applied Physics Letters is copyrighted by The American Institute of Physics....

  14. Interfacial segregation and grain boundary embrittlement: an overview and critical assessment of experimental data and calculated results

    Czech Academy of Sciences Publication Activity Database

    Lejček, Pavel; Šob, Mojmír; Paidar, Václav

    2017-01-01

    Roč. 87, Jun (2017), s. 83-139 ISSN 0079-6425 R&D Projects: GA ČR GBP108/12/G043; GA ČR(CZ) GA16-24711S; GA MŠk(CZ) LQ1601 Institutional support: RVO:68378271 ; RVO:68081723 Keywords : solute segregation * interfacial embrittlement * grain boundary * free surface * computer modeling * measurements of local composition Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 31.140, year: 2016

  15. Role of grain boundary diffusion on ion-induced composition change in alloys at elevated temperatures. [A/sup +/ ions

    Energy Technology Data Exchange (ETDEWEB)

    Morita, K.; Hayashibara, M.; Ohno, H.; Itoh, N. (Nagoya Univ. (Japan). Dept. of Crystalline Materials Science)

    1984-05-01

    We prepared nickel specimens which contain gold impurity only near the grain boundaries and measured thermal segregation of gold onto the surface and the change in the composition induced by bombardment with Ar/sup +/ ions. It is found that irradiation causes composition change over a depth much larger than the thickness of the altered layer for Ni-Au alloys. It is also found that when a two-layered Ni-Au film is bombarded with gold atoms from the nickel side at elevated temperatures, the nickel is protected by a thin gold film segregated on the nickel surface.

  16. Clean Grain Boundary Found in C14/Body-Center-Cubic Multi-Phase Metal Hydride Alloys

    Directory of Open Access Journals (Sweden)

    Hao-Ting Shen

    2016-06-01

    Full Text Available The grain boundaries of three Laves phase-related body-center-cubic (bcc solid-solution, metal hydride (MH alloys with different phase abundances were closely examined by scanning electron microscopy (SEM, transmission electron microscopy (TEM, and more importantly, electron backscatter diffraction (EBSD techniques. By using EBSD, we were able to identify the alignment of the crystallographic orientations of the three major phases in the alloys (C14, bcc, and B2 structures. This finding confirms the presence of crystallographically sharp interfaces between neighboring phases, which is a basic assumption for synergetic effects in a multi-phase MH system.

  17. Interactions between Lattice Dislocations and Grain Boundaries in Ni3Al Investigated by Means of In Situ TEM and Computer Modelling Experiments

    NARCIS (Netherlands)

    Pestman, B.J.; Hosson, J.Th.M. De

    1992-01-01

    The interaction between lattice dislocations and grain boundaries in Ni3Al has been investigated by means of in situ TEM deformation experiments. The interaction between screw dislocations and a coherent twin boundary could be analyzed in detail. The interaction mechanism found experimentally was

  18. Atomistic calculations of hydrogen interactions with Ni3Al grain boundaries and Ni/Ni3Al interfaces

    International Nuclear Information System (INIS)

    Baskes, M.I.; Angelo, J.E.; Moody, N.R.

    1995-01-01

    Embedded Atom Method (EAM) potentials have been developed for the Ni/Al/H system. The potentials have been fit to numerous properties of this system. For example, these potentials represent the structural and elastic properties of bulk Ni, Al, Ni 3 Al, and NiAl quite well. In addition the potentials describe the solution and migration behavior of hydrogen in both nickel and aluminum. A number of calculations using these potentials have been performed. It is found that hydrogen strongly prefers sites in Ni 3 Al that are surrounded by 6 Ni atoms. Calculations of the trapping of hydrogen to a number of grain boundaries in Ni 3 Al have been performed as a function of hydrogen chemical potential at room temperature. The failure of these bicrystals under tensile stress has been examined and will be compared to the failure of pure Ni 3 Al boundaries. Boundaries containing a preponderance of nickel are severely weakened by hydrogen. In order to investigate the potential embrittlement of γ/γ' alloys, trapping of hydrogen to a spherical Ni 3 Al precipate in nickel as a function of chemical potential at room temperature has been calculated. It appears that the boundary is not a strong trap for hydrogen, hence embrittlement in these alloys is not primarily due to interactions of hydrogen with the γ/γ interface

  19. Recombination in Perovskite Solar Cells : Significance of Grain Boundaries, Interface Traps, and Defect Ions

    NARCIS (Netherlands)

    Sherkar, Tejas; Momblona, Cristina; Gil-Escrig, Lidon; Avila, Jorge; Sessolo, Michele; Bolink, Henk J.; Koster, Lambert

    2017-01-01

    Trap-assisted recombination, despite being lower as compared with traditional inorganic solar cells, is still the dominant recombination mechanism in perovskite solar cells (PSCs) and limits their efficiency. We investigate the attributes of the primary trap-assisted recombination channels (grain

  20. Delaunay-Network Modelling of Creep Failure in Regular Polycrystalline Aggregates by Grain Boundary Cavitation

    NARCIS (Netherlands)

    Burg, M.W.D. van der; Giessen, E. van der

    1994-01-01

    In polycrystalline materials at elevated temperatures subjected to stationary loading, creep fracture occurs as a result of failure mechanisms on the size scale of grains, namely the nucleation and diffusive growth of cavities until coalescence leads to microcracks. In this paper, a polycrystalline